Effect of reference loads on fracture mechanics analysis of surface cracked pipe based on reference stress method

International Nuclear Information System (INIS)

Shim, Do Jun; Son, Beom Goo; Kim, Young Jin; Kim, Yun Jae

2004-01-01

To investigate relevance of the definition of the reference stress to estimate J and C * for surface crack problems, this paper compares FE J and C * results for surface cracked pipes with those estimated according to the reference stress approach using various definitions of the reference stress. Pipes with part circumferential inner surface crack and finite internal axial crack are considered, subject to internal pressure and global bending. The crack depth and aspect ratio are systematically varied. The reference stress is defined in four different ways using (I) the local limit load, (II) the global limit load, (III) the global limit load determined from the FE limit analysis, and (IV) the optimised reference load. It is found that the reference stress based on the local limit load gives overall excessively conservative estimates of J and C * . Use of the global limit load clearly reduces the conservatism, compared to that of the local limit load, although it can provide sometimes non-conservative estimates of J and C * . The use of the FE global limit load gives overall non-conservative estimates of J and C * . The reference stress based on the optimised reference load gives overall accurate estimates of J and C * , compared to other definitions of the reference stress. Based on the present finding, general guidance on the choice of the reference stress for surface crack problems is given

Analysis of shot-peening and residual stress relaxation in the nickel-based superalloy RR1000

International Nuclear Information System (INIS)

Foss, B.J.; Gray, S.; Hardy, M.C.; Stekovic, S.; McPhail, D.S.; Shollock, B.A.

2013-01-01

This work assesses the residual stress relaxation of the nickel-based alloy RR1000 due to thermal exposure and dwell-fatigue loading. A number of different characterization methods, including X-ray residual stress analysis, electron back-scattered diffraction, microhardness testing and focused ion beam secondary electron imaging, contributed to a detailed study of the shot-peened region. Thermal exposure at 700 °C resulted in a large reduction in the residual stresses and work-hardening effects in the alloy, but the subsurface remained in a beneficial compressive state. Oxidizing environments caused recrystallization in the near surface, but did not affect the residual stress-relaxation behaviour. Dwell-fatigue loading caused the residual stresses to return to approximately zero at nearly all depths. This work forms part of an ongoing investigation to determine the effects of shot-peening in this alloy with the motivation to improve the fatigue and oxidation resistance at 700 °C

Residual stress analysis in thick uranium films

International Nuclear Information System (INIS)

Hodge, A.M.; Foreman, R.J.; Gallegos, G.F.

2005-01-01

Residual stress analysis was performed on thick, 1-25 μm, depleted uranium (DU) films deposited on an Al substrate by magnetron sputtering. Two distinct characterization techniques were used to measure substrate curvature before and after deposition. Stress evaluation was performed using the Benabdi/Roche equation, which is based on beam theory of a bi-layer material. The residual stress evolution was studied as a function of coating thickness and applied negative bias voltage (0, -200, -300 V). The stresses developed were always compressive; however, increasing the coating thickness and applying a bias voltage presented a trend towards more tensile stresses and thus an overall reduction of residual stresses

Stress analysis and deformation prediction of sheet metal workpieces based on finite element simulation

Directory of Open Access Journals (Sweden)

Ren Penghao

2017-01-01

Full Text Available After aluminum alloy sheet metal parts machining, the residual stress release will cause a large deformation. To solve this problem, this paper takes a aluminum alloy sheet aerospace workpiece as an example, establishes the theoretical model of elastic deformation and the finite element model, and places quantitative initial stress in each element of machining area, analyses stress release simulation and deformation. Through different initial stress release simulative analysis of deformation of the workpiece, a linear relationship between initial stress and deformation is found; Through simulative analysis of coupling direction-stress release, the superposing relationship between the deformation caused by coupling direction-stress and the deformation caused by single direction stress is found. The research results provide important theoretical support for the stress threshold setting and deformation controlling of the workpieces in the production practice.

Assessment of possibility of primary water stress corrosion cracking occurrence based on residual stress analysis in pressurizer safety nozzle of nuclear power plant

International Nuclear Information System (INIS)

Lee, Kyoung Soo; Kim, W.; Lee, Jeong Geun

2012-01-01

Primary water stress corrosion cracking (PWSCC) is a major safety concern in the nuclear power industry worldwide. PWSCC is known to initiate only in the condition in which sufficiently high tensile stress is applied to alloy 600 tube material or alloy 82/182 weld material in pressurized water reactor operating environments. However, it is still uncertain how much tensile stress is required to generate PWSCC or what causes such high tensile stress. This study was performed to predict the magnitude of weld residual stress and operating stress and compare it with previous experimental results for PWSCC initiation. For the study, a pressurizer safety nozzle was selected because it is reported to be vulnerable to PWSCC in overseas plants. The assessment was conducted by numerical analysis. Before performing stress analysis for plant conditions, a preliminary mock-up analysis was done. The result of the preliminary analysis was validated by residual stress measurement in the mockup. After verification of the analysis methodology, an analysis under plant conditions was conducted. The analysis results show that the stress level is not high enough to initiate PWSCC. If a plant is properly welded and operated, PWSCC is not likely to occur in the pressurizer safety nozzle.

Study of Sesame (Sesame indicum L. Cultivars based on Morphological Characteristics Under Water Deficit Stress Condition Using Factor Analysis

Directory of Open Access Journals (Sweden)

A Asghari

2014-03-01

Full Text Available In order to evaluation sesame cultivars based on morphological characteristics under water deficit stress condition using factor analysis, an experiment was conducted as a split plot based on randomized complete block design with three replications during 2009 in Research Center of Agriculture and Natural Resources in Parsabad. In this experiment, irrigation as the main factor at three levels (50, 75 and 100 percent of crop water requirement and ten sesame cultivars as the sub-factor were studied. The water requirement of sesame was calculated using CROPWAT software (Penman-Monteith method according to FAO-56. Results showed significant differences between the cultivars and the irrigation levels for all studied traits. Interaction between cultivars and irrigation levels was significant for some of traits. Comparisons of means showed that in water deficit condition, yield and all of traits reduced. In all traits the greatest amounts observed in complete irrigation treatment. In 50 percent of water requirement treatment, amount of leaf chlorophyll, root length, root branches and root length/plant height ratio were greater than other treatments. The Karaj1, Ultan, Naze and IS cultivars were better than other cultivars in stress and non stress condition. In factor analysis 5 and 4 first factors in non stress and stress condition explained 91.36 and 89.52 percent of trait variance, respectively. Grouping of sesame cultivars based on first and second factors in non stress conditions showed that Karaj1, Ultan and Naze cultivars were better than other cultivars. Also, in stress conditions Karaj1 and Ultan cultivars grouped as water deficit stress and better cultivars.

Stress analysis program system for nuclear vessel: STANSAS

International Nuclear Information System (INIS)

Okamoto, Asao; Michikami, Shinsuke

1979-01-01

IHI has developed a computer system of stress analysis and evaluation for nuclear vessels: STANSAS (STress ANalysis System for Axi-symmetric Structure). The system consists of more than twenty independent programs divided into the following six parts. 1. Programs for opening design by code rule. 2. Calculation model generating programs. 3. Load defining programs. 4. Structural analysis programs. 5. Load data/calculation results plotting programs. 6. Stress evaluation programs. Each program is connected with its pre- or post-processor through three data-bases which enable automatic data transfer. The user can make his choice of structural analysis programs in accordance with the problem to be solved. The interface to STANSAS can be easily installed in generalized structural analysis programs such as NASTRAN and MARC. For almost all tables and figures in the stress report, STANSAS has the function to print or plot out. The complicated procedures of ''Design by Analysis'' for pressure vessels have been well standardized by STANSAS. The system will give a high degree of efficiency and confidence to the design work. (author)

Utility of magnetic resonance imaging-based finite element analysis for the biomechanical stress analysis of hemorrhagic and non-hemorrhagic carotid plaques

International Nuclear Information System (INIS)

Sadat, U.; Teng, Z.; Young, V.E.; Li, Z.Y.; Gillard, J.H.

2011-01-01

Biomechanical stress analysis has been used for plaque vulnerability assessment. The presence of plaque hemorrhage (PH) is a feature of plaque vulnerability and is associated with thromboembolic ischemic events. The purpose of the present study was to use finite element analysis (FEA) to compare the stress profiles of hemorrhagic and non-hemorrhagic profiles. Forty-five consecutive patients who had suffered a cerebrovascular ischemic event with an underlying carotid artery disease underwent high-resolution magnetic resonance imaging (MRI) of their symptomatic carotid artery in a 1.5-T MRI system. Axial images were manually segmented for various plaque components and used for FEA. Maximum critical stress (M-Cstress SL ) for each slice was determined. Within a plaque, the maximum M-Cstress SL for each slice of a plaque was selected to represent the maximum critical stress of that plaque (M-Cstress PL ) and used to compare hemorrhagic and non-hemorrhagic plaques. A total of 62% of plaques had hemorrhage. It was observed that plaques with hemorrhage had significantly higher stress (M-Cstress PL ) than plaques without PH (median [interquartile range]: 315kPa [247-434] vs. 200kPa [171-282], P=0.003). Hemorrhagic plaques have higher biomechanical stresses than non-hemorrhagic plaques. MRI-based FEA seems to have the potential to assess plaque vulnerability. (author)

Feasibility of wall stress analysis of abdominal aortic aneurysms using three-dimensional ultrasound.

Science.gov (United States)

Kok, Annette M; Nguyen, V Lai; Speelman, Lambert; Brands, Peter J; Schurink, Geert-Willem H; van de Vosse, Frans N; Lopata, Richard G P

2015-05-01

Abdominal aortic aneurysms (AAAs) are local dilations that can lead to a fatal hemorrhage when ruptured. Wall stress analysis of AAAs is a novel tool that has proven high potential to improve risk stratification. Currently, wall stress analysis of AAAs is based on computed tomography (CT) and magnetic resonance imaging; however, three-dimensional (3D) ultrasound (US) has great advantages over CT and magnetic resonance imaging in terms of costs, speed, and lack of radiation. In this study, the feasibility of 3D US as input for wall stress analysis is investigated. Second, 3D US-based wall stress analysis was compared with CT-based results. The 3D US and CT data were acquired in 12 patients (diameter, 35-90 mm). US data were segmented manually and compared with automatically acquired CT geometries by calculating the similarity index and Hausdorff distance. Wall stresses were simulated at P = 140 mm Hg and compared between both modalities. The similarity index of US vs CT was 0.75 to 0.91 (n = 12), with a median Hausdorff distance ranging from 4.8 to 13.9 mm, with the higher values found at the proximal and distal sides of the AAA. Wall stresses were in accordance with literature, and a good agreement was found between US- and CT-based median stresses and interquartile stresses, which was confirmed by Bland-Altman and regression analysis (n = 8). Wall stresses based on US were typically higher (+23%), caused by geometric irregularities due to the registration of several 3D volumes and manual segmentation. In future work, an automated US registration and segmentation approach is the essential point of improvement before pursuing large-scale patient studies. This study is a first step toward US-based wall stress analysis, which would be the modality of choice to monitor wall stress development over time because no ionizing radiation and contrast material are involved. Copyright © 2015 Society for Vascular Surgery. Published by Elsevier Inc. All rights reserved.

Thermographic Analysis of Stress Distribution in Welded Joints

Directory of Open Access Journals (Sweden)

Domazet Ž.

2010-06-01

Full Text Available The fatigue life prediction of welded joints based on S-N curves in conjunction with nominal stresses generally is not reliable. Stress distribution in welded area affected by geometrical inhomogeneity, irregular welded surface and weld toe radius is quite complex, so the local (structural stress concept is accepted in recent papers. The aim of this paper is to determine the stress distribution in plate type aluminum welded joints, to analyze the reliability of TSA (Thermal Stress Analysis in this kind of investigations, and to obtain numerical values for stress concentration factors for practical use. Stress distribution in aluminum butt and fillet welded joints is determined by using the three different methods: strain gauges measurement, thermal stress analysis and FEM. Obtained results show good agreement - the TSA mutually confirmed the FEM model and stresses measured by strain gauges. According to obtained results, it may be stated that TSA, as a relatively new measurement technique may in the future become a standard tool for the experimental investigation of stress concentration and fatigue in welded joints that can help to develop more accurate numerical tools for fatigue life prediction.

Thermographic Analysis of Stress Distribution in Welded Joints

Science.gov (United States)

Piršić, T.; Krstulović Opara, L.; Domazet, Ž.

2010-06-01

The fatigue life prediction of welded joints based on S-N curves in conjunction with nominal stresses generally is not reliable. Stress distribution in welded area affected by geometrical inhomogeneity, irregular welded surface and weld toe radius is quite complex, so the local (structural) stress concept is accepted in recent papers. The aim of this paper is to determine the stress distribution in plate type aluminum welded joints, to analyze the reliability of TSA (Thermal Stress Analysis) in this kind of investigations, and to obtain numerical values for stress concentration factors for practical use. Stress distribution in aluminum butt and fillet welded joints is determined by using the three different methods: strain gauges measurement, thermal stress analysis and FEM. Obtained results show good agreement - the TSA mutually confirmed the FEM model and stresses measured by strain gauges. According to obtained results, it may be stated that TSA, as a relatively new measurement technique may in the future become a standard tool for the experimental investigation of stress concentration and fatigue in welded joints that can help to develop more accurate numerical tools for fatigue life prediction.

Thermal Stress Analysis and Structure Parameter Selection for a Bi2Te3-Based Thermoelectric Module

Science.gov (United States)

Gao, Jun-Ling; Du, Qun-Gui; Zhang, Xiao-Dan; Jiang, Xin-Qiang

2011-05-01

The output power and conversion efficiency of thermoelectric modules (TEMs) are mainly determined by their material properties, i.e., Seebeck coefficient, electrical resistivity, and thermal conductivity. In practical applications, due to the influence of the harsh environment, the mechanical properties of TEMs should also be considered. Using the finite-element analysis (FEA) model in ANSYS software, we present the thermal stress distribution of a TEM based on the anisotropic mechanical properties and thermoelectric properties of hot-pressed materials. By analyzing the possibilities of damage along the cleavage plane of Bi2Te3-based thermoelectric materials and by optimizing the structure parameters, a TEM with better mechanical performance is obtained. Thus, a direction for improving the thermal stress resistance of TEMs is presented.

Analysis of residual stresses in a long hollow cylinder

International Nuclear Information System (INIS)

Tokovyy, Yuriy V.; Ma, Chien-Ching

2011-01-01

This paper presents an analytical method for solving the axisymmetric stress problem for a long hollow cylinder subjected to locally-distributed residual (incompatible) strains. This method is based on direct integration of the equilibrium and compatibility equations, which thereby have been reduced to the set of two governing equations for two key functions with corresponding boundary and integral conditions. The governing equations were solved by making use of the Fourier integral transformation. Application of the method is illustrated with an analysis of the welding residual stresses in a butt-welded thick-walled pipe. - Highlights: → A solution to the axisymmetric stress problem for a hollow cylinder is constructed. → The cylinder is subjected to a field of locally-distributed residual strains. → The method is based on direct integration of the equilibrium equations. → An application of our solution to analysis of welding residual stresses is considered.

Wall stress analysis of abdominal aortic aneurysms using 3D ultrasound

NARCIS (Netherlands)

Kok, A. M.; Nguyen, V.L.; Speelman, L.; Schurink, G.W.H.; van de Vosse, F.N.; Lopata, R.G.P.

2014-01-01

Wall stress analysis of abdominal aortic aneurysms is a novel tool that has proven high potential to improve risk stratification of abdominal aortic aneurysms (AAAs). Wall stress analysis is based on computed tomography (CT) and magnetic resonance imaging, however, 3D ultrasound (US) has not been

Mindfulness-Based Stress Reduction

Science.gov (United States)

... R S T U V W X Y Z Mindfulness-Based Stress Reduction (MBSR) Information 6 Things You ... Disease and Dementia (12/20/13) Research Spotlights Mindfulness-Based Stress Reduction, Cognitive-Behavioral Therapy Shown To ...

Stress analysis and deformation prediction of sheet metal workpieces based on finite element simulation

OpenAIRE

Ren Penghao; Wang Aimin; Wang Xiaolong; Zhang Yanlin

2017-01-01

After aluminum alloy sheet metal parts machining, the residual stress release will cause a large deformation. To solve this problem, this paper takes a aluminum alloy sheet aerospace workpiece as an example, establishes the theoretical model of elastic deformation and the finite element model, and places quantitative initial stress in each element of machining area, analyses stress release simulation and deformation. Through different initial stress release simulative analysis of deformation ...

The stress analysis evaluation and pipe support layout for pressurizer discharge system

International Nuclear Information System (INIS)

Mao Qing; Wang Wei; Zhang Yixiong

2000-01-01

The author presents the stress analysis and evaluation of pipe layout and support adjustment process for Qinshan phase II pressurizer discharge system. Using PDL-SYSPIPE INTERFACE software, the characteristic parameters of the system are gained from 3-D CAD engineering design software PDL and outputted as the input date file format of special pipe stress analysis program SYSPIPE. Based on that, SYSPIPE program fast stress analysis function is applied in adjusting pipe layout , support layout and support types. According to RCC-M standard, the pipe stress analysis and evaluation under deadweight, internal pressure, thermal expansion, seismic, pipe rupture and discharge loads are fulfilled

14 CFR 33.62 - Stress analysis.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Stress analysis. 33.62 Section 33.62... STANDARDS: AIRCRAFT ENGINES Design and Construction; Turbine Aircraft Engines § 33.62 Stress analysis. A stress analysis must be performed on each turbine engine showing the design safety margin of each turbine...

Stress: a concept analysis.

Science.gov (United States)

Goodnite, Patricia M

2014-01-01

To analyze the concept of stress and provide an operational definition of stress. Literature review revealed that stress is a commonly used, but often ambiguous, term. Findings supported a definition of stress entailing an individual's perception of a stimulus as overwhelming, which in turn elicits a measurable response resulting in a transformed state. This analysis adopts a dynamic definition of stress that may serve to encourage communication, promote reflection, and enhance concept understanding. This definition may provide direction for future work, as well as enhance efforts to serve patients affected by stress. © 2013 Wiley Periodicals, Inc.

Transcriptome Analysis of Sunflower Genotypes with Contrasting Oxidative Stress Tolerance Reveals Individual- and Combined- Biotic and Abiotic Stress Tolerance Mechanisms.

Directory of Open Access Journals (Sweden)

Vemanna S Ramu

Full Text Available In nature plants are often simultaneously challenged by different biotic and abiotic stresses. Although the mechanisms underlying plant responses against single stress have been studied considerably, plant tolerance mechanisms under combined stress is not understood. Also, the mechanism used to combat independently and sequentially occurring many number of biotic and abiotic stresses has also not systematically studied. From this context, in this study, we attempted to explore the shared response of sunflower plants to many independent stresses by using meta-analysis of publically available transcriptome data and transcript profiling by quantitative PCR. Further, we have also analyzed the possible role of the genes so identified in contributing to combined stress tolerance. Meta-analysis of transcriptomic data from many abiotic and biotic stresses indicated the common representation of oxidative stress responsive genes. Further, menadione-mediated oxidative stress in sunflower seedlings showed similar pattern of changes in the oxidative stress related genes. Based on this a large scale screening of 55 sunflower genotypes was performed under menadione stress and those contrasting in oxidative stress tolerance were identified. Further to confirm the role of genes identified in individual and combined stress tolerance the contrasting genotypes were individually and simultaneously challenged with few abiotic and biotic stresses. The tolerant hybrid showed reduced levels of stress damage both under combined stress and few independent stresses. Transcript profiling of the genes identified from meta-analysis in the tolerant hybrid also indicated that the selected genes were up-regulated under individual and combined stresses. Our results indicate that menadione-based screening can identify genotypes not only tolerant to multiple number of individual biotic and abiotic stresses, but also the combined stresses.

Rotors stress analysis and design

CERN Document Server

Vullo, Vincenzo

2013-01-01

Stress and strain analysis of rotors subjected to surface and body loads, as well as to thermal loads deriving from temperature variation along the radius, constitutes a classic subject of machine design. Nevertheless attention is limited to rotor profiles for which governing equations are solvable in closed form. Furthermore very few actual engineering issues may relate to structures for which stress and strain analysis in the linear elastic field and, even more, under non-linear conditions (i.e. plastic or viscoelastic conditions) produces equations to be solved in closed form. Moreover, when a product is still in its design stage, an analytical formulation with closed-form solution is of course simpler and more versatile than numerical methods, and it allows to quickly define a general configuration, which may then be fine-tuned using such numerical methods. In this view, all subjects are based on analytical-methodological approach, and some new solutions in closed form are presented. The analytical formul...

Stress-based Variable-inductor for Electronic Ballasts

DEFF Research Database (Denmark)

Zhang, Lihui; Xia, Yongming; Lu, Kaiyuan

2015-01-01

Current-controlled variable inductors adjust the inductance of an alternating current (ac) coil by applying a controlled dc current to saturate the iron cores of the ac coil. The controlled dc current has to be maintained during operation, which results in increased power losses. This paper prese......-based variable inductor concept is validated using a 3-D finite-element analysis. A prototype was manufactured, and the experimental results are presented. A linear relationship between inductance and applied stress can be achieved.......Current-controlled variable inductors adjust the inductance of an alternating current (ac) coil by applying a controlled dc current to saturate the iron cores of the ac coil. The controlled dc current has to be maintained during operation, which results in increased power losses. This paper...... presents a new stress-based variable inductor to control inductance using the inverse magnetostrictive effect of a magnetostrictive material. The stress can be applied by a piezoelectrical material, and thus a voltage-controlled variable inductor can be realized with zero-power consumption. The new stress...

Genome wide analysis of stress responsive WRKY transcription factors in Arabidopsis thaliana

Directory of Open Access Journals (Sweden)

Shaiq Sultan

2016-04-01

Full Text Available WRKY transcription factors are a class of DNA-binding proteins that bind with a specific sequence C/TTGACT/C known as W-Box found in promoters of genes which are regulated by these WRKYs. From previous studies, 43 different stress responsive WRKY transcription factors in Arabidopsis thaliana, identified and then categorized in three groups viz., abiotic, biotic and both of these stresses. A comprehensive genome wide analysis including chromosomal localization, gene structure analysis, multiple sequence alignment, phylogenetic analysis and promoter analysis of these WRKY genes was carried out in this study to determine the functional homology in Arabidopsis. This analysis led to the classification of these WRKY family members into 3 major groups and subgroups and showed evolutionary relationship among these groups on the base of their functional WRKY domain, chromosomal localization and intron/exon structure. The proposed groups of these stress responsive WRKY genes and annotation based on their position on chromosomes can also be explored to determine their functional homology in other plant species in relation to different stresses. The result of the present study provides indispensable genomic information for the stress responsive WRKY transcription factors in Arabidopsis and will pave the way to explain the precise role of various AtWRKYs in plant growth and development under stressed conditions.

Study on Real-Time Simulation Analysis and Inverse Analysis System for Temperature and Stress of Concrete Dam

Directory of Open Access Journals (Sweden)

Lei Zhang

2015-01-01

Full Text Available In the concrete dam construction, it is very necessary to strengthen the real-time monitoring and scientific management of concrete temperature control. This paper constructs the analysis and inverse analysis system of temperature stress simulation, which is based on various useful data collected in real time in the process of concrete construction. The system can produce automatically data file of temperature and stress calculation and then achieve the remote real-time simulation calculation of temperature stress by using high performance computing techniques, so the inverse analysis can be carried out based on a basis of monitoring data in the database; it fulfills the automatic feedback calculation according to the error requirement and generates the corresponding curve and chart after the automatic processing and analysis of corresponding results. The system realizes the automation and intellectualization of complex data analysis and preparation work in simulation process and complex data adjustment in the inverse analysis process, which can facilitate the real-time tracking simulation and feedback analysis of concrete temperature stress in construction process and enable you to discover problems timely, take measures timely, and adjust construction scheme and can well instruct you how to ensure project quality.

Nonlinear analysis of 0-3 polarized PLZT microplate based on the new modified couple stress theory

Science.gov (United States)

Wang, Liming; Zheng, Shijie

2018-02-01

In this study, based on the new modified couple stress theory, the size- dependent model for nonlinear bending analysis of a pure 0-3 polarized PLZT plate is developed for the first time. The equilibrium equations are derived from a variational formulation based on the potential energy principle and the new modified couple stress theory. The Galerkin method is adopted to derive the nonlinear algebraic equations from governing differential equations. And then the nonlinear algebraic equations are solved by using Newton-Raphson method. After simplification, the new model includes only a material length scale parameter. In addition, numerical examples are carried out to study the effect of material length scale parameter on the nonlinear bending of a simply supported pure 0-3 polarized PLZT plate subjected to light illumination and uniform distributed load. The results indicate the new model is able to capture the size effect and geometric nonlinearity.

Stress analysis of primary pipe rigid support of the in pile loop

International Nuclear Information System (INIS)

Hasibuan, Dj.

1998-01-01

Base on requirement of the safety analysis report and operation planning preparation on the in pile loop by using the fuel bundle in the test section, the stress analysis of primary pipe support has been done. The analysis was performed for the 3 (three) points of pipe support, which are chosen by random selection, i.e.: GU 2001, GU 2002, and GU 2331. The analysis result showed that the maximum allowable stress was greater then the actual stress. It is concluded that the existing supports fulfil the safety requirement

A Comparison of Students' Perceptions of Stress in Parallel Problem-Based and Lecture-Based Curricula.

Science.gov (United States)

Wardley, C Sonia; Applegate, E Brooks; Almaleki, A Deyab; Van Rhee, James A

2016-03-01

A 6-year longitudinal study was conducted to compare the perceived stress experienced during a 2-year master's physician assistant program by 5 cohorts of students enrolled in either problem-based learning (PBL) or lecture-based learning (LBL) curricular tracks. The association of perceived stress with academic achievement was also assessed. Students rated their stress levels on visual analog scales in relation to family obligations, financial concerns, schoolwork, and relocation and overall on 6 occasions throughout the program. A mixed model analysis of variance examined the students' perceived level of stress by curriculum and over time. Regression analysis further examined school work-related stress after controlling for other stressors and possible lag effect of stress from the previous time point. Students reported that overall stress increased throughout the didactic year followed by a decline in the clinical year with statistically significant curricular (PBL versus LBL) and time differences. PBL students also reported significantly more stress resulting from school work than LBL students at some time points. Moreover, when the other measured stressors and possible lag effects were controlled, significant differences between PBL and LBL students' perceived stress related to school work persisted at the 8- and 12-month measurement points. Increased stress in both curricula was associated with higher achievement in overall and individual organ system examination scores. Physician assistant programs that embrace a PBL pedagogy to prepare students to think clinically may need to provide students with additional support through the didactic curriculum.

Advanced Techniques of Stress Analysis

Directory of Open Access Journals (Sweden)

Simion TATARU

2013-12-01

Full Text Available This article aims to check the stress analysis technique based on 3D models also making a comparison with the traditional technique which utilizes a model built directly into the stress analysis program. This comparison of the two methods will be made with reference to the rear fuselage of IAR-99 aircraft, structure with a high degree of complexity which allows a meaningful evaluation of both approaches. Three updated databases are envisaged: the database having the idealized model obtained using ANSYS and working directly on documentation, without automatic generation of nodes and elements (with few exceptions, the rear fuselage database (performed at this stage obtained with Pro/ ENGINEER and the one obtained by using ANSYS with the second database. Then, each of the three databases will be used according to arising necessities.The main objective is to develop the parameterized model of the rear fuselage using the computer aided design software Pro/ ENGINEER. A review of research regarding the use of virtual reality with the interactive analysis performed by the finite element method is made to show the state- of- the-art achieved in this field.

Advanced stress analysis of PWR containments in the region of nozzles

International Nuclear Information System (INIS)

Schauer, G.

1977-01-01

As an example of the stress analysis of a nozzle in a PWR steel containment, an advanced stress analysis of a personnel lock is presented. Contrary to the calculations by means of numerical shell programs usual till now, this advanced stress analysis was executed with the finite-element-method. Because of their theory, the shell programs compute mathematically exact results, but at the intersection of two shells the notch stresses cannot be analyzed well. A further disadvantage must be seen in the fact that there is a great distance between the real critical region near the intersection line and the calculation point, which lies on the neutral axis of the shell. The study shows that the results obtained to date which are based on the shell theory and calculate stresses at a fictitious intersection line can be improved and that there is a possibility to get stress values adjacent to the real intersection line. (Auth.)

Rethinking Stress in Parents of Preterm Infants: A Meta-Analysis

Science.gov (United States)

Schappin, Renske; Wijnroks, Lex; Uniken Venema, Monica M. A. T.; Jongmans, Marian J.

2013-01-01

Background With improved medical outcome in preterm infants, the psychosocial situation of their families is receiving increasing attention. For parents, the birth of a preterm infant is generally regarded as a stressful experience, and therefore many interventions are based on reducing parental stress. Nevertheless, it remains unclear whether parents of children born preterm experience more stress than parents of term-born children, which would justify these interventions. This meta-analysis provides a comprehensive account of parental stress in parents of preterm infants, from birth of the infant through to their adolescence. Mean levels of stress in specific domains of family functioning were investigated, and stress levels in parents of preterm and term infants, and fathers and mothers of preterm infants, were compared. Furthermore, we investigated moderators of parental stress. Methods and Findings A random-effects meta-analysis was conducted including 38 studies describing 3025 parents of preterm (stress was measured with two parent-reported questionnaires, the Parenting Stress Index and the Parental Stressor Scale: Neonatal Intensive Care Unit. The results indicate that parents of preterm-born children experience only slightly more stress than parents of term-born children, with small effect sizes. Furthermore, mothers have slightly more stress than fathers, but these effect sizes are also small. Parents report more stress for infants with lower gestational ages and lower birth weights. There is a strong effect for infant birth year, with decreasing parental stress from the 1980s onward, probably due to increased quality of care for preterm infants. Conclusions Based on our findings we argue that prematurity can best be regarded as one of the possible complications of birth, and not as a source of stress in itself. PMID:23405105

Brain structure in post-traumatic stress disorder: A voxel-based morphometry analysis.

Science.gov (United States)

Tan, Liwen; Zhang, Li; Qi, Rongfeng; Lu, Guangming; Li, Lingjiang; Liu, Jun; Li, Weihui

2013-09-15

This study compared the difference in brain structure in 12 mine disaster survivors with chronic post-traumatic stress disorder, 7 cases of improved post-traumatic stress disorder symptoms, and 14 controls who experienced the same mine disaster but did not suffer post-traumatic stress disorder, using the voxel-based morphometry method. The correlation between differences in brain structure and post-traumatic stress disorder symptoms was also investigated. Results showed that the gray matter volume was the highest in the trauma control group, followed by the symptoms-improved group, and the lowest in the chronic post-traumatic stress disorder group. Compared with the symptoms-improved group, the gray matter volume in the lingual gyrus of the right occipital lobe was reduced in the chronic post-traumatic stress disorder group. Compared with the trauma control group, the gray matter volume in the right middle occipital gyrus and left middle frontal gyrus was reduced in the symptoms-improved group. Compared with the trauma control group, the gray matter volume in the left superior parietal lobule and right superior frontal gyrus was reduced in the chronic post-traumatic stress disorder group. The gray matter volume in the left superior parietal lobule was significantly positively correlated with the State-Trait Anxiety Inventory subscale score in the symptoms-improved group and chronic post-traumatic stress disorder group (r = 0.477, P = 0.039). Our findings indicate that (1) chronic post-traumatic stress disorder patients have gray matter structural damage in the prefrontal lobe, occipital lobe, and parietal lobe, (2) after post-traumatic stress, the disorder symptoms are improved and gray matter structural damage is reduced, but cannot recover to the trauma-control level, and (3) the superior parietal lobule is possibly associated with chronic post-traumatic stress disorder. Post-traumatic stress disorder patients exhibit gray matter abnormalities.

Brain structure in post-traumatic stress disorder: A voxel-based morphometry analysis

Science.gov (United States)

Tan, Liwen; Zhang, Li; Qi, Rongfeng; Lu, Guangming; Li, Lingjiang; Liu, Jun; Li, Weihui

2013-01-01

This study compared the difference in brain structure in 12 mine disaster survivors with chronic post-traumatic stress disorder, 7 cases of improved post-traumatic stress disorder symptoms, and 14 controls who experienced the same mine disaster but did not suffer post-traumatic stress disorder, using the voxel-based morphometry method. The correlation between differences in brain structure and post-traumatic stress disorder symptoms was also investigated. Results showed that the gray matter volume was the highest in the trauma control group, followed by the symptoms-improved group, and the lowest in the chronic post-traumatic stress disorder group. Compared with the symptoms-improved group, the gray matter volume in the lingual gyrus of the right occipital lobe was reduced in the chronic post-traumatic stress disorder group. Compared with the trauma control group, the gray matter volume in the right middle occipital gyrus and left middle frontal gyrus was reduced in the symptoms-improved group. Compared with the trauma control group, the gray matter volume in the left superior parietal lobule and right superior frontal gyrus was reduced in the chronic post-traumatic stress disorder group. The gray matter volume in the left superior parietal lobule was significantly positively correlated with the State-Trait Anxiety Inventory subscale score in the symptoms-improved group and chronic post-traumatic stress disorder group (r = 0.477, P = 0.039). Our findings indicate that (1) chronic post-traumatic stress disorder patients have gray matter structural damage in the prefrontal lobe, occipital lobe, and parietal lobe, (2) after post-traumatic stress, the disorder symptoms are improved and gray matter structural damage is reduced, but cannot recover to the trauma-control level, and (3) the superior parietal lobule is possibly associated with chronic post-traumatic stress disorder. Post-traumatic stress disorder patients exhibit gray matter abnormalities. PMID:25206550

Work-related critical incidents in hospital-based health care providers and the risk of post-traumatic stress symptoms, anxiety, and depression: a meta-analysis

NARCIS (Netherlands)

de Boer, Jacoba; Lok, Anja; van 't Verlaat, Ellen; Duivenvoorden, Hugo J.; Bakker, Arnold B.; Smit, Bert J.

2011-01-01

This meta-analysis reviewed existing data on the impact of work-related critical incidents in hospital-based health care professionals. Work-related critical incidents may induce post-traumatic stress symptoms or even post-traumatic stress disorder (PTSD), anxiety, and depression and may negatively

Concept Analysis: Alzheimer's Caregiver Stress.

Science.gov (United States)

Llanque, Sarah; Savage, Lynette; Rosenburg, Neal; Caserta, Michael

2016-01-01

The aim of this article was to analyze the concept of caregiver stress in the context of caring for a person with Alzheimer's disease and related dementias. Currently, there are more than 15 million unpaid caregivers for persons suffering from Alzheimer's disease and related dementias. This unpaid care can be stressful for caregivers due to the chronic nature of the disease process, as well as other factors. The paper incorporates the modified method of Wilson's concept analysis procedure to analyze the concept of caregiver stress. A review of the literature was undertaken using the Cumulative Index to Nursing and Allied Health Literature, Google Scholar, and PubMed. A theoretical definition of caregiver stress is provided, and the defining attributes, related concepts, antecedents, and consequences of caregiver stress are proposed, and case studies are presented. The analysis demonstrates that caregiver stress is the unequal exchange of assistance among people who stand in close relationship to one another, which results in emotional and physical stress on the caregiver. Implications for future nursing research and practice conclude the paper. © 2014 Wiley Periodicals, Inc.

Surface stress-based biosensors.

Science.gov (United States)

Sang, Shengbo; Zhao, Yuan; Zhang, Wendong; Li, Pengwei; Hu, Jie; Li, Gang

2014-01-15

Surface stress-based biosensors, as one kind of label-free biosensors, have attracted lots of attention in the process of information gathering and measurement for the biological, chemical and medical application with the development of technology and society. This kind of biosensors offers many advantages such as short response time (less than milliseconds) and a typical sensitivity at nanogram, picoliter, femtojoule and attomolar level. Furthermore, it simplifies sample preparation and testing procedures. In this work, progress made towards the use of surface stress-based biosensors for achieving better performance is critically reviewed, including our recent achievement, the optimally circular membrane-based biosensors and biosensor array. The further scientific and technological challenges in this field are also summarized. Critical remark and future steps towards the ultimate surface stress-based biosensors are addressed. Copyright © 2013 Elsevier B.V. All rights reserved.

Blade dynamic stress analysis of rotating bladed disks

Directory of Open Access Journals (Sweden)

Kellner J.

2007-10-01

Full Text Available The paper deals with mathematical modelling of steady forced bladed disk vibrations and with dynamic stress calculation of the blades. The blades are considered as 1D kontinuum elastic coupled with three-dimensional elastic disk centrally clamped into rotor rotating with constant angular speed. The steady forced vibrations are generated by the aerodynamic forces acting along the blade length. By using modal synthesis method the mathematical model of the rotating bladed disk is condensed to calculate steady vibrations. Dynamic stress analysis of the blades is based on calculation of the time dependent reduced stress in blade cross-sections by using Hubert-Misses-Hencky stress hypothesis. The presented method is applied to real turbomachinery rotor with blades connected on the top with shroud.

Finite element based stress analysis of BWR internals exposed to accident loads

Energy Technology Data Exchange (ETDEWEB)

Altstadt, E; Weiss, F P; Werner, M; Willschuetz, H G

1998-10-01

During a hypothetical accident the reactor pressure vessel internals of boiling water reactors can be exposed to considerable loads resulting from temperature gradients and pressure waves. Three dimensional FE models were developed for the core shroud, the upper and the lower core supporting structure, the steam separator pipes and the feed water distributor. The models of core shroud, upper core structure and lower core structure were coupled by means of the substructure technique. All FE models can be used for thermal and for structural mechanical analyses. As an example the FE analysis for the case of a station black-out scenario (loss of power supply for the main circulating pumps) with subsequent emergency core cooling is demonstrated. The transient temperature distributions within the core shroud and within the steam dryer pipes as well were calculated based on the fluid temperatures and the heat transfer coefficients provided by thermo-hydraulic codes. At the maximum temperature gradients in the core shroud, the mechanical stress distribution was computed in a static analysis with the actual temperature field being the load. (orig.)

Stress analysis and life prediction of gas turbine blade

Science.gov (United States)

Hsiung, H. C.; Dunn, A. J.; Woodling, D. R.; Loh, D. L.

1988-01-01

A stress analysis procedure is presented for a redesign of the Space Shuttle Main Engine high pressure fuel turbopump turbine blades. The analysis consists of the one-dimensional scoping analysis to support the design layout and the follow-on three-dimensional finite element analysis to confirm the blade design at operating loading conditions. Blade life is evaluated based on high-cycle fatigue and low-cycle fatigue.

Investigating role stress in frontline bank employees: A cluster based approach

Directory of Open Access Journals (Sweden)

Arti Devi

2013-09-01

Full Text Available An effective role stress management programme would benefit from a segmentation of employees based on their experience of role stressors. This study explores role stressor based segments of frontline bank employees towards providing a framework for designing such a programme. Cluster analysis on a random sample of 501 frontline employees of commercial banks in Jammu and Kashmir (India revealed three distinct segments – “overloaded employees”, “unclear employees”, and “underutilised employees”, based on their experience of role stressors. The findings suggest a customised approach to role stress management, with the role stress management programme designed to address cluster specific needs.

Evaluation of stress gradient by x-ray stress measurement based on change in angle phi

International Nuclear Information System (INIS)

Sasaki, Toshihiko; Kuramoto, Makoto; Yoshioka, Yasuo.

1985-01-01

A new principle of X-ray stress evaluation for a sample with steep stress gradient has been prosed. The feature of this method is that the stress is determined by using so-called phi-method based on the change of phi-angle and thus has no effect on the penetration depth of X-rays. The procedure is as follows; firstly, an average stress within the penetration depth of X-rays is determined by changing only phi-angle under a fixed psi-angle, and then a distribution of the average stress vs. the penetration depth of X-rays is detected by repeating the similar procedure at different psi-angles. The following conclusions were found out as the result of residual stress measurements on a carbon steel of type S 55 C polished by emery paper. This method is practical enough to use for a plane stress problem. And the assumption of a linear stress gradient adopted in the authors' previous investigations is valid. In case of a triaxial stress analysis, this method is effective for the solution of three shearing stresses. However, three normal stresses can not be solved perfectly except particular psi-angles. (author)

Study on elastic-plastic deformation analysis using a cyclic stress-strain curve

International Nuclear Information System (INIS)

Igari, Toshihide; Setoguchi, Katsuya; Yamauchi, Masafumi

1983-01-01

This paper presents the results of the elastic-plastic deformation analysis using a cyclic stress-strain curve with an intention to apply this method for predicting the low-cycle fatigue life. Uniaxial plastic cycling tests were performed on 2 1/4Cr-1Mo steel to investigate the correspondence between the cyclic stress-strain curve and the hysteresis loop, and also to determine what mathematical model should be used for analysis of deformation at stress reversal. Furthermore, a cyclic in-plane bending test was performed on a flat plate to clarify the validity of the cyclic stress-strain curve-based theoretical analysis. The results obtained are as follows: (1) The cyclic stress-strain curve corresponds nearly to the ascending curve of hysteresis loop scaled by a factor of 1/2 for both stress and strain. Therefore, the cyclic stress-strain curve can be determined from the shape of hysteresis loop, for simplicity. (2) To perform the elastic-plastic deformation analysis using the cyclic stress-strain curve is both practical and effective for predicting the cyclic elastic-plastic deformation of structures at the stage of advanced cycles. And Masing model can serve as a suitable mathematical model for such a deformation analysis. (author)

Analysis of initial changes in the proteins of soybean root tip under flooding stress using gel-free and gel-based proteomic techniques.

Science.gov (United States)

Yin, Xiaojian; Sakata, Katsumi; Nanjo, Yohei; Komatsu, Setsuko

2014-06-25

Flooding has a severe negative effect on soybean cultivation in the early stages of growth. To obtain a better understanding of the response mechanisms of soybean to flooding stress, initial changes in root tip proteins under flooding were analyzed using two proteomic techniques. Two-day-old soybeans were treated with flooding for 3, 6, 12, and 24h. The weight of soybeans increased during the first 3h of flooding, but root elongation was not observed. Using gel-based and gel-free proteomic techniques, 115 proteins were identified in root tips, of which 9 proteins were commonly detected by both methods. The 71 proteins identified by the gel-free proteomics were analyzed by a hierarchical clustering method based on induction levels during the flooding, and the proteins were divided into 5 clusters. Additional interaction analysis of the proteins revealed that ten proteins belonging to cluster I formed the center of a protein interaction network. mRNA expression analysis of these ten proteins showed that citrate lyase and heat shock protein 70 were down-regulated, whereas calreticulin was up-regulated in initial phase of flooding. These results suggest that flooding stress to soybean induces calcium-related signal transduction, which might play important roles in the early responses to flooding. Flooding has a severe negative effect on soybean cultivation, particularly in the early stages of growth. To better understand the response mechanisms of soybean to the early stages of flooding stress, two proteomic techniques were used. Two-day-old soybeans were treated without or with flooding for 3, 6, 12, and 24h. The fresh weight of soybeans increased during the first 3h of flooding stress, but the growth then slowed and no root elongation was observed. Using gel-based and gel-free proteomic techniques, 115 proteins were identified in root tips, of which 9 proteins were commonly detected by both methods. The 71 proteins identified by the gel-free proteomics were analyzed

Stress assessment based on EEG univariate features and functional connectivity measures.

Science.gov (United States)

Alonso, J F; Romero, S; Ballester, M R; Antonijoan, R M; Mañanas, M A

2015-07-01

The biological response to stress originates in the brain but involves different biochemical and physiological effects. Many common clinical methods to assess stress are based on the presence of specific hormones and on features extracted from different signals, including electrocardiogram, blood pressure, skin temperature, or galvanic skin response. The aim of this paper was to assess stress using EEG-based variables obtained from univariate analysis and functional connectivity evaluation. Two different stressors, the Stroop test and sleep deprivation, were applied to 30 volunteers to find common EEG patterns related to stress effects. Results showed a decrease of the high alpha power (11 to 12 Hz), an increase in the high beta band (23 to 36 Hz, considered a busy brain indicator), and a decrease in the approximate entropy. Moreover, connectivity showed that the high beta coherence and the interhemispheric nonlinear couplings, measured by the cross mutual information function, increased significantly for both stressors, suggesting that useful stress indexes may be obtained from EEG-based features.

Finite Element Residual Stress Analysis of Planetary Gear Tooth

Directory of Open Access Journals (Sweden)

Jungang Wang

2013-01-01

Full Text Available A method to simulate residual stress field of planetary gear is proposed. In this method, the finite element model of planetary gear is established and divided to tooth zone and profile zone, whose different temperature field is set. The gear's residual stress simulation is realized by the thermal compression stress generated by the temperature difference. Based on the simulation, the finite element model of planetary gear train is established, the dynamic meshing process is simulated, and influence of residual stress on equivalent stress of addendum, pitch circle, and dedendum of internal and external meshing planetary gear tooth profile is analyzed, according to non-linear contact theory, thermodynamic theory, and finite element theory. The results show that the equivalent stresses of planetary gear at both meshing and nonmeshing surface are significantly and differently reduced by residual stress. The study benefits fatigue cracking analysis and dynamic optimization design of planetary gear train.

Stress analysis of closure bolts for shipping casks

International Nuclear Information System (INIS)

Mok, G.C.; Fischer, L.E.; Hsu, S.T.

1993-01-01

This report specifies the requirements and criteria for stress analysis of closure bolts for shipping casks containing nuclear spent fuels or high level radioactive materials. The specification is based on existing information conceming the structural behavior, analysis, and design of bolted joints. The approach taken was to extend the ASME Boiler and Pressure Vessel Code requirements and criteria for bolting analysis of nuclear piping and pressure vessels to include the appropriate design and load characteristics of the shipping cask. The characteristics considered are large, flat, closure lids with metal-to-metal contact within the bolted joint; significant temperature and impact loads; and possible prying and bending effects. Specific formulas and procedures developed apply to the bolt stress analysis of a circular, flat, bolted closure. The report also includes critical load cases and desirable design practices for the bolted closure, an in-depth review of the structural behavior of bolted joints, and a comprehensive bibliography of current information on bolted joints

The Stress and Stiffness Analysis of Diaphragm

Directory of Open Access Journals (Sweden)

Qu Dongyue

2017-01-01

Full Text Available Diaphragm coupling with its simple structure, small size, high reliability, which can compensate for its input and output displacement deviation by its elastic deformation, is widely used in aerospace, marine, and chemical etc. This paper uses the ANSYS software and its APDL language to analysis the stress distribution when the diaphragm under the load of torque, axial deviation, centrifugal force, angular deviation and multiple loads. We find that the value of maximum stress usually appears in the outer or inner transition region and the axial deviation has a greater influence to the distribution of the stress. Based on above, we got three kinds of stiffness for axial, angular and torque, which the stiffness of diaphragm is nearly invariable. The results can be regard as an important reference for design and optimization of diaphragm coupling.

Stress analysis of aspherical coated particle with inner pressure

Energy Technology Data Exchange (ETDEWEB)

Liu Bing, E-mail: bingliu@tsinghua.edu.cn [Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing, 100084 (China); Yang Lin; Liang Tongxiang; Tang Chunhe [Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing, 100084 (China)

2012-10-15

Coated particles used in HTR fuel element sustain the inner pressure during irradiation as a pressure vessel. In actually the coated particle is not real spherical but with some asphericity, the stress distribution in the vessel is not uniform, coated layer in aspherical particle sustain more additional stress due to the asphericity. In this paper, the geometric shape distribution is summarized based on actual coated particle statistic. A mechanical analysis model is proposed for SiC layer by geometric combinations, and stress distribution of coated particle with a flat is calculated. The results show that the local maximum stress of aspherical particle increased two times than that of ideal spherical coated particle, which increase the failure probability under irradiation and high temperature.

Mechanical stress analysis for the poloidal field coils of TORE SUPRA

International Nuclear Information System (INIS)

Ane, J.M.; Perin, J.P.

1985-01-01

Hoop stresses, up to 100 MPa, in the poloidal field coils of TORE SUPRA have to be reacted back to the main body of the coil where a conductor ends or is twisted for an interturn or an interlayer transition. The load is taken by shear stress through the insulation. Carefully designed configurations, based on 1D, 2D and 3D analysis results, limit the shear stress levels to 15 MPa. A fatigue test of a conductor termination has shown that the experimental results are in good agreement with the calculated stresses

Near-wall extension of a non-equilibrium, omega-based Reynolds stress model

International Nuclear Information System (INIS)

Nguyen, Tue; Behr, Marek; Reinartz, Birgit

2011-01-01

In this paper, the development of a new ω-based Reynolds stress model that is consistent with asymptotic analysis in the near wall region and with rapid distortion theory in homogeneous turbulence is reported. The model is based on the SSG/LRR-ω model developed by Eisfeld (2006) with three main modifications. Firstly, the near wall behaviors of the redistribution, dissipation and diffusion terms are modified according to the asymptotic analysis and a new blending function based on low Reynolds number is proposed. Secondly, an anisotropic dissipation tensor based on the Reynolds stress inhomogeneity (Jakirlic et al., 2007) is used instead of the original isotropic model. Lastly, the SSG redistribution term, which is activated far from the wall, is replaced by Speziale's non-equilibrium model (Speziale, 1998).

How Do You #relax When You're #stressed? A Content Analysis and Infodemiology Study of Stress-Related Tweets.

Science.gov (United States)

Doan, Son; Ritchart, Amanda; Perry, Nicholas; Chaparro, Juan D; Conway, Mike

2017-06-13

was rest & vacation, followed by nature and water. When we applied the classifiers to the cities dataset, the proportion of stress tweets in New York and San Diego was substantially higher than that in Los Angeles and San Francisco. In addition, we found that characteristic expressions of stress and relaxation varied for each city based on its geolocation. This content analysis and infodemiology study revealed that Twitter, when used in conjunction with natural language processing techniques, is a useful data source for understanding stress and stress management strategies, and can potentially supplement infrequently collected survey-based stress data. ©Son Doan, Amanda Ritchart, Nicholas Perry, Juan D Chaparro, Mike Conway. Originally published in JMIR Public Health and Surveillance (http://publichealth.jmir.org), 13.06.2017.

Reliability-oriented environmental thermal stress analysis of fuses in power electronics

DEFF Research Database (Denmark)

Bahman, A. S.; Iannuzzo, F.; Holmgaard, T.

2017-01-01

This paper investigates the thermo-mechanical stress experienced by axial lead fuses used in power electronics. Based on some experience, the approach used in this paper is pure thermal cycling, and the found failure mechanisms have been investigated through X-ray imaging. A two-step analysis, i...... element has been confirmed thanks to the analysis performed. Finally, the fatigue analysis is presented obtained by FEM-based fatigue tool....

Nuclear class 1 piping stress analysis

International Nuclear Information System (INIS)

Lucas, J.C.R.; Maneschy, J.E.; Mariano, L.A.; Tamura, M.

1981-01-01

A nuclear class 1 piping stress analysis, according to the ASME code, is presented. The TRHEAT computer code has been used to determine the piping wall thermal gradient. The Nupipe computer code was employed for the piping stress analysis. Computer results were compared with the allowable criteria from the ASME code. (Author) [pt

Predator-based psychosocial stress animal model of PTSD: Preclinical assessment of traumatic stress at cognitive, hormonal, pharmacological, cardiovascular and epigenetic levels of analysis.

Science.gov (United States)

Zoladz, Phillip R; Diamond, David M

2016-10-01

Research on post-traumatic stress disorder (PTSD) is faced with the challenge of understanding how a traumatic experience produces long-lasting detrimental effects on behavior and brain functioning, and more globally, how stress exacerbates somatic disorders, including cardiovascular disease. Moreover, the design of translational research needs to link animal models of PTSD to clinically relevant risk factors which address why only a subset of traumatized individuals develop persistent psychopathology. In this review, we have summarized our psychosocial stress rodent model of PTSD which is based on well-described PTSD-inducing risk factors, including a life-threatening experience, a sense of horror and uncontrollability, and insufficient social support. Specifically, our animal model of PTSD integrates acute episodes of inescapable exposure of immobilized rats to a predator with chronic daily social instability. This stress regimen produces PTSD-like effects in rats at behavioral, cognitive, physiological, pharmacological and epigenetic levels of analysis. We have discussed a recent extension of our animal model of PTSD in which stress exacerbated coronary pathology following an ischemic event, assessed in vitro. In addition, we have reviewed our research investigating pharmacological and non-pharmacological therapeutic strategies which may have value in clinical approaches toward the treatment of traumatized people. Overall, our translational approach bridges the gap between human and animal PTSD research to create a framework with which to enhance our understanding of the biological basis of trauma-induced pathology and to assess therapeutic approaches in the treatment of psychopathology. Copyright © 2016 Elsevier Inc. All rights reserved.

Association between psychosocial stress and hypertension: a systematic review and meta-analysis.

Science.gov (United States)

Liu, Mei-Yan; Li, Na; Li, William A; Khan, Hajra

2017-06-01

The etiology of hypertension is various and complex, involving both genetic and behavioral factors. The relationship between psychosocial stress and hypertension has been hypothesized. More and more people experience increased anxiety, depression, and chronic psychosocial stress brought on by globalization, cultural changes, socioeconomic changes, and stress at the work place. Although a plethora of studies have investigated the interaction between psychosocial stress and hypertension, this relationship is still contentious. The objective of this study is twofold. First, a review of recent advancements in our understanding of the relationship between psychosocial stress and hypertension. Second, a meta-analysis aiming to assess the relationship between chronic psychosocial stress and blood pressure. We systematically searched and identified relevant studies from five databases, including PubMed, Cochrane Library, China National Knowledge Infrastructure (CNKI), CQVIP, and the Wanfang Database until April 2016. Eleven studies encompassing 5696 participants were included in the final analysis. Data showed that psychosocial stress was associated with an increased risk of hypertension (OR = 2.40, 95% CI = 1.65-3.49), and hypertensive patients had a higher incidence of psychosocial stress compared to normotension patients (OR = 2.69, 95% CI = 2.32-3.11). Based on our meta-analysis, chronic psychosocial stress may be a risk factor for hypertension. The few cohort and case-control studies on the association between psychosocial stress and hypertension employed variable definition of stressors and the responses, making the meta-analysis difficult. Although we found an association between chronic psychosocial stress and hypertension, more studies are needed to confirm this relationship.

Mapping residual stresses in PbWO4 crystals using photo-elastic analysis

International Nuclear Information System (INIS)

Lebeau, M.; Gobbi, L.; Majni, G.; Paone, N.; Pietroni, P.; Rinaldi, D.

2005-01-01

Large scintillating crystals are affected by internal stresses induced by the crystal growth temperature gradient remanence. Cutting boules (ingots) into finished crystal shapes allows for a partial tension relaxation but residual stresses remain the main cause of breaking. Quality control of residual stresses is essential in the application of Scintillating Crystals to high-energy physics calorimeters (e.g. CMS ECAL at CERN LHC). In this context the industrial process optimisation towards stress reduction is mandatory. We propose a fast technique for testing samples during the production process in order to evaluate the residual stress distribution after the first phases of mechanical processing. We mapped the stress distribution in PbWO 4 slabs cut from the same production boule. The analysis technique is based on the stress intensity determination using the photo-elastic properties of the samples. The stress distribution is mapped in each sample. The analysis shows that there are regions of high residual tension close to the seed position and at the boule periphery. These results should allow for adapting the industrial process to producing crystals with lower residual stresses

The shape of change in perceived stress, negative affect, and stress sensitivity during mindfulness based stress reduction

NARCIS (Netherlands)

Snippe, E.; Dziak, J.J.; Lanza, S.T.; Nyklicek, I.; Wichers, M.

2017-01-01

Both daily stress and the tendency to react to stress with heightened levels of negative affect (i.e., stress sensitivity) are important vulnerability factors for adverse mental health outcomes. Mindfulness-based stress reduction (MBSR) may help to reduce perceived daily stress and stress

The Shape of Change in Perceived Stress, Negative Affect, and Stress Sensitivity During Mindfulness-Based Stress Reduction

NARCIS (Netherlands)

Snippe, Evelien; Dziak, John J.; Lanza, Stephanie T.; Nykliek, Ivan; Wichers, Marieke

Both daily stress and the tendency to react to stress with heightened levels of negative affect (i.e., stress sensitivity) are important vulnerability factors for adverse mental health outcomes. Mindfulness-based stress reduction (MBSR) may help to reduce perceived daily stress and stress

Analysis of Residual Stress and Deformation of Rolling Strengthen Crankshaft Fillet

Directory of Open Access Journals (Sweden)

Han Shaojun

2016-01-01

Full Text Available Based on the analysis of crankshaft fillet rolling process, used ANSYS finite element analysis software to conduct the elastic-plastic mechanical simulation of crankshaft rolling process, and gained the variation law of the residual stress and plastic deformation in the radial path of the fillet under different rolling laps and rolling pressure. Established the relationship between the rolling pressure and the plastic deformation and residual stress of the fillet, and provided theoretical support for the evaluation and detection of the crankshaft rolling quality.

Work-related critical incidents in hospital-based health care providers and the risk of post-traumatic stress symptoms, anxiety, and depression: a meta-analysis.

Science.gov (United States)

de Boer, Jacoba; Lok, Anja; Van't Verlaat, Ellen; Duivenvoorden, Hugo J; Bakker, Arnold B; Smit, Bert J

2011-07-01

This meta-analysis reviewed existing data on the impact of work-related critical incidents in hospital-based health care professionals. Work-related critical incidents may induce post-traumatic stress symptoms or even post-traumatic stress disorder (PTSD), anxiety, and depression and may negatively affect health care practitioners' behaviors toward patients. Nurses and doctors often cope by working part time or switching jobs. Hospital administrators and health care practitioners themselves may underestimate the effects of work-related critical incidents. Relevant online databases were searched for original research published from inception to 2009 and manual searches of the Journal of Traumatic Stress, reference lists, and the European Traumatic Stress Research Database were conducted. Two researchers independently decided on inclusion and study quality. Effect sizes were estimated using standardized mean differences with 95% confidence intervals. Consistency was evaluated, using the I(2)-statistic. Meta-analysis was performed using the random effects model. Eleven studies, which included 3866 participants, evaluated the relationship between work-related critical incidents and post-traumatic stress symptoms. Six of these studies, which included 1695 participants, also reported on the relationship between work-related critical incidents and symptoms of anxiety and depression. Heterogeneity among studies was high and could not be accounted for by study quality, character of the incident, or timing of data collection. Pooled effect sizes for the impact of work-related critical incidents on post-traumatic stress symptoms, anxiety, and depression were small to medium. Remarkably, the effect was more pronounced in the longer than in the shorter term. In conclusion, this meta-analysis supports the hypothesis that work-related critical incidents are positively related to post-traumatic stress symptoms, anxiety, and depression in hospital-based health care professionals

Method for analysis and assessment of the relation between stress and reliability of knowledge-based actions in the probabilistic safety analysis

International Nuclear Information System (INIS)

Fassmann, Werner

2014-06-01

According to the current theoretical and empirical state-of-the-art, stress has to be understood as the emotional and cognitive reaction by which humans adapt to situations which imply real or imagined danger, threat, or frustration of important personal goals or needs. The emotional reaction to such situations can be so extreme that rational coping with the situation will be precluded. In less extreme cases, changes of cognitive processes underlying human action will occur, which may systematically affect the reliability of tasks personnel has to perform in a stressful situation. Reliable task performance by personnel of nuclear power plants and other risk technologies is also affected by such effects. The method developed in the frame of the research and development project RS1198 sponsored by the German Federal Ministry for Economic Affairs and Energy (BMWi) addresses both aspects of emotional and cognitive coping with stressful situations. Analytical and evaluation steps of the approach provide guidance to the end users on how to capture and quantify the contribution of stress-related emotional and cognitive factors to the reliable performance of knowledge-based actions. For this purpose, a suitable guideline has been developed. Further research for clarifying open questions has been identified. A case study application illustrates how to use the method. Part of the work performed in this project was dedicated to a review addressing the question to which extent Swain's approach to the analysis and evaluation of stress is in line with current scientific knowledge. Suitable suggestions for updates have been developed.

Statistical Analysis of Stress Signals from Bridge Monitoring by FBG System

Directory of Open Access Journals (Sweden)

Xiao-Wei Ye

2018-02-01

Full Text Available In this paper, a fiber Bragg grating (FBG-based stress monitoring system instrumented on an orthotropic steel deck arch bridge is demonstrated. The FBG sensors are installed at two types of critical fatigue-prone welded joints to measure the strain and temperature signals. A total of 64 FBG sensors are deployed around the rib-to-deck and rib-to-diagram areas at the mid-span and quarter-span of the investigated orthotropic steel bridge. The local stress behaviors caused by the highway loading and temperature effect during the construction and operation periods are presented with the aid of a wavelet multi-resolution analysis approach. In addition, the multi-modal characteristic of the rainflow counted stress spectrum is modeled by the method of finite mixture distribution together with a genetic algorithm (GA-based parameter estimation approach. The optimal probability distribution of the stress spectrum is determined by use of Bayesian information criterion (BIC. Furthermore, the hot spot stress of the welded joint is calculated by an extrapolation method recommended in the specification of International Institute of Welding (IIW. The stochastic characteristic of stress concentration factor (SCF of the concerned welded joint is addressed. The proposed FBG-based stress monitoring system and probabilistic stress evaluation methods can provide an effective tool for structural monitoring and condition assessment of orthotropic steel bridges.

Development of residual stress analysis procedure for fitness-for-service assessment of welded structure

International Nuclear Information System (INIS)

Kim, Jong Sung; Jin, Tae Eun; Dong, P.; Prager, M.

2003-01-01

In this study, a state of art review of existing residual stress analysis techniques and representative solutions is presented in order to develop the residual stress analysis procedure for Fitness-For-Service(FFS) assessment of welded structure. Critical issues associated with existing residual stress solutions and their treatments in performing FFS are discussed. It should be recognized that detailed residual stress evolution is an extremely complicated phenomenon that typically involves material-specific thermomechanical/metallurgical response, welding process physics, and structural interactions within a component being welded. As a result, computational procedures can vary significantly from highly complicated numerical techniques intended only to elucidate a small part of the process physics to cost-effective procedures that are deemed adequate for capturing some of the important features in a final residual stress distribution. Residual stress analysis procedure for FFS purposes belongs to the latter category. With this in mind, both residual stress analysis techniques and their adequacy for FFS are assessed based on both literature data and analyses performed in this investigation

Concept Analysis: Alzheimer’s Caregiver Stress

Science.gov (United States)

Llanque, Sarah; Savage, Lynette; Rosenburg, Neal; Honor’s, BA; Caserta, Michael

2015-01-01

AIM The aim of this article was to analyze the concept of caregiver stress in the context of caring for a person with Alzheimer’s disease and related dementias. BACKGROUND Currently, there are more than 15 million unpaid care-givers for persons suffering from Alzheimer’s disease and related dementias. This unpaid care can be stressful for caregivers due to the chronic nature of the disease process, as well as other factors. METHOD The paper incorporates the modified method of Wilson’s concept analysis procedure to analyze the concept of caregiver stress. DATA SOURCES A review of the literature was undertaken using the Cumulative Index to Nursing and Allied Health Literature, Google Scholar, and PubMed. RESULTS A theoretical definition of caregiver stress is provided, and the defining attributes, related concepts, antecedents, and consequences of caregiver stress are proposed, and case studies are presented. CONCLUSIONS The analysis demonstrates that caregiver stress is the unequal exchange of assistance among people who stand in close relationship to one another, which results in emotional and physical stress on the caregiver. Implications for future nursing research and practice conclude the paper. PMID:24787468

Stress analysis of PCV nozzle junction

International Nuclear Information System (INIS)

Uchiyama, Shoichi; Oikawa, Tsuneo; Hoshino, Seizo

1976-01-01

Most of various pressure vessels comprise each one cylindrical shell and one or more nozzles. In this study, in order to analyze the stress in the structures of this type as minutely and exactly as possible, the program for stress analysis by the finite element method was made, which is required for the strength analysis for three-dimensional structures. Especially, the problem of the stress distribution around nozzle junctions was solved theoretically with the program. The program for the analysis developed in this study is provided with various functions, such as the input generator for cylindrical, conical and spherical shells, and plotter, and is very covenient. The accuracy of analysis is very good. The method of analysis and the calculation of the rigidity matrices for the deformation in plane and bending are explained. The result of the stress analysis around the nozzle junctions of a containment vessel with this program was in good agreement with experimental data and the result with SAP-4 code, therefore the propriety of the calculated result with this program was proved. Also calculations were carried out on three cases, namely a flat plate fixed at one end with distributed load, a cylinder fixed at one end with internal pressure, and an I-beam fixed at one end with concentrated load. The calculated results agreed well with theoretical solutions in all cases. (Kako, I.)

Mindfulness-based stress reduction for treating chronic headache: A systematic review and meta-analysis.

Science.gov (United States)

Anheyer, Dennis; Leach, Matthew J; Klose, Petra; Dobos, Gustav; Cramer, Holger

2018-01-01

Background Mindfulness-based stress reduction/cognitive therapy are frequently used for pain-related conditions, but their effects on headache remain uncertain. This review aimed to assess the efficacy and safety of mindfulness-based stress reduction/cognitive therapy in reducing the symptoms of chronic headache. Data sources and study selection MEDLINE/PubMed, Scopus, CENTRAL, and PsychINFO were searched to 16 June 2017. Randomized controlled trials comparing mindfulness-based stress reduction/cognitive therapy with usual care or active comparators for migraine and/or tension-type headache, which assessed headache frequency, duration or intensity as a primary outcome, were eligible for inclusion. Risk of bias was assessed using the Cochrane Tool. Results Five randomized controlled trials (two on tension-type headache; one on migraine; two with mixed samples) with a total of 185 participants were included. Compared to usual care, mindfulness-based stress reduction/cognitive therapy did not improve headache frequency (three randomized controlled trials; standardized mean difference = 0.00; 95% confidence interval = -0.33,0.32) or headache duration (three randomized controlled trials; standardized mean difference = -0.08; 95% confidence interval = -1.03,0.87). Similarly, no significant difference between groups was found for pain intensity (five randomized controlled trials; standardized mean difference = -0.78; 95% confidence interval = -1.72,0.16). Conclusions Due to the low number, small scale and often high or unclear risk of bias of included randomized controlled trials, the results are imprecise; this may be consistent with either an important or negligible effect. Therefore, more rigorous trials with larger sample sizes are needed.

Automatic stress-relieving music recommendation system based on photoplethysmography-derived heart rate variability analysis.

Science.gov (United States)

Shin, Il-Hyung; Cha, Jaepyeong; Cheon, Gyeong Woo; Lee, Choonghee; Lee, Seung Yup; Yoon, Hyung-Jin; Kim, Hee Chan

2014-01-01

This paper presents an automatic stress-relieving music recommendation system (ASMRS) for individual music listeners. The ASMRS uses a portable, wireless photoplethysmography module with a finger-type sensor, and a program that translates heartbeat signals from the sensor to the stress index. The sympathovagal balance index (SVI) was calculated from heart rate variability to assess the user's stress levels while listening to music. Twenty-two healthy volunteers participated in the experiment. The results have shown that the participants' SVI values are highly correlated with their prespecified music preferences. The sensitivity and specificity of the favorable music classification also improved as the number of music repetitions increased to 20 times. Based on the SVI values, the system automatically recommends favorable music lists to relieve stress for individuals.

A Comparative Study Between Strain And Stress Based Forming Limit Analysis By Applying Several Phenomenological Yield Criteria

International Nuclear Information System (INIS)

Butuc, Marilena C.; Vincze, Gabriela T.; Gracio, Jose J.; Barata da Rocha, A.

2005-01-01

The present work aims at analyzing a comparative study between the strain-based forming limit criterion (FLD) and the stress-based forming limit criterion (FLSD), under linear and complex strain paths. The selected material is an AA5182-0 aluminium alloy. Some relevant remarks about stress-based forming limit criterion concept are presented

Assessment of stress reactions of recruits based on quantitative analysis of the characteristics of fingertip photoplethysmographic

Directory of Open Access Journals (Sweden)

Li-jun XIAO

2011-09-01

Full Text Available Objective To investigate the feasibility of stress assessment based on specific quantification techniques and analysis of stress status with photoplethysmographic(PPG signals.Methods The PPG signals were stratified and randomly sampled from 58 recruits before and after stress induced by International Affective Pictures Systems(IAPS images of negative emotion.The signals were collected and processed in a tool called HC2180-D,an enhanced solution of a blood flow monitoring system,through which the characteristic parameters of pulsatile waveform were derived as components of bioinformation for quantitative and comparative study.A concise mental rating scale,the "brief profile of mood state"(BPOMS,was used as criterion.Results As the characteristic parameter and biomarker were derived,significant increases in values were observed in both the vasoconstriction/vasodilation fraction(CDF and the ordinate of the area under the pulse contour of the vasoconstriction phase(Y2 when the recruits were shown IAPS images of negative emotion(P 0.05 were shown.The values of both the CDF and the Y2 were positively correlated in mid-range to tension,depression,and anger(P < 0.05,and in low-range to fatigue and confusion(P < 0.05.The values were negatively correlated in mid-range with vigor(P < 0.05.Conclusion The characteristic parameter and biomarker derived from the pulsatile waveform obtained at the fingertip are highly sensitive and can be utilized as measures in the quantitative assessment of stress response among recruits.

Stress and psychological factors before a migraine attack: A time-based analysis

Directory of Open Access Journals (Sweden)

Makino Mariko

2008-09-01

Full Text Available Abstract Background The objective of this study is to examine the stress and mood changes of Japanese subjects over the 1–3 days before a migraine headache. Methods The study participants were 16 patients with migraines who consented to participate in this study. Each subject kept a headache diary four times a day for two weeks. They evaluated the number of stressful events, daily hassles, domestic and non-domestic stress, anxiety, depressive tendency and irritability by visual analog scales. The days were classified into migraine days, pre-migraine days, buffer days and control days based on the intensity of the headaches and accompanying symptoms, and a comparative study was conducted for each factor on the migraine days, pre-migraine days and control days. Results The stressful event value of pre-migraine days showed no significant difference compared to other days. The daily hassle value of pre-migraine days was the highest and was significantly higher than that of buffer days. In non-domestic stress, values on migraine days were significantly higher than on other days, and there was no significant difference between pre-migraine days and buffer days or between pre-migraine days and control days. There was no significant difference in the values of domestic stress between the categories. In non-domestic stress, values on migraine days were significantly higher than other days, and there was no significant difference between pre-migraine days and buffer days or between pre-migraine days and control days. There was little difference in sleep quality on migraine and pre-migraine days, but other psychological factors were higher on migraine days than on pre-migraine days. Conclusion Psychosocial stress preceding the onset of migraines by several days was suggested to play an important role in the occurrence of migraines. However, stress 2–3 days before a migraine attack was not so high as it has been reported to be in the United States and

Stress analysis of pressure vessels

International Nuclear Information System (INIS)

Kim, B.K.; Song, D.H.; Son, K.H.; Kim, K.S.; Park, K.B.; Song, H.K.; So, J.Y.

1979-01-01

This interim report contains the results of the effort to establish the stress report preparation capability under the research project ''Stress analysis of pressure vessels.'' 1978 was the first year in this effort to lay the foundation through the acquisition of SAP V structural analysis code and a graphic terminal system for improved efficiency of using such code. Software programming work was developed in pre- and post processing, such as graphic presentation of input FEM mesh geometry and output deformation or mode shope patterns, which was proven to be useful when using the FEM computer code. Also, a scheme to apply fracture mechanics concept was developed in fatigue analysis of pressure vessels. (author)

Residual stresses analysis of friction stir welding using one-way FSI simulation

International Nuclear Information System (INIS)

Kang, Sung Wook; Jang, Beom Seon; Song, Ha Cheol

2015-01-01

When certain mechanisms, such as plastic deformations and temperature gradients, occur and are released in a structure, stresses remain because of the shape of the structure and external constraints. These stresses are referred to as residual stresses. The base material locally expands during heating in the welding process. When the welding is completed and cooled to room temperature, the residual stresses are left at nearly the yield strength level. In the case of friction stir welding, the maximum temperature is 80% to 90% of the melting point of the materials. Thus, the residual stresses in the welding process are smaller than those in other fusion welding processes; these stresses have not been considered previously. However, friction stir welding residual stresses are sometimes measured at approximately 70% or above. These residual stresses significantly affect fatigue behavior and lifetime. The present study investigates the residual stress distributions in various welding conditions and shapes of friction stir welding. In addition, the asymmetric feature is considered in temperature and residual stress distribution. Heat transfer analysis is conducted using the commercial computational fluid dynamics program Fluent, and results are used in the finite element structural analysis with the ANSYS Multiphysics software. The calculated residual stresses are compared with experimental values using the X-ray diffraction method.

Residual stress analysis on materials with steep stress gradient by using X-ray incidence at higher angles

International Nuclear Information System (INIS)

Ohya, Shin-ichi; Yoshioka, Yasuo; Maeno, Shigeki

1996-01-01

X-ray stress measurements for isotropic polycrystalline are materials are usually carried out by the sin 2 ψ method under the assumption of no stress gradient in X-ray penetration depth. When a steep stress gradient exists in the vicinity of surface layer, however, non-linear sin 2 ψ relation is observed and the sin 2 ψ method cannot be applied on such cases. Although several X-ray stress analyzers have been developed for materials with steep stress gradient in the surface layer, it is desirable to use diffraction data at higher incident angles of ψ 0 as possible as close on 90 degrees in order to determine the both values of surface stress and stress gradient with high accuracy. In the present study, an X-ray stress analyzer based on Ω geometry was fabricated to enable X-ray incidence at higher angle of ψ 0 . The X-ray detector was positioned on -η side against X-ray incident beam. Both of the residual surface stress and stress gradient were determined by use of the COSψ method on shot-peened steel and silicon nitride specimens. This prototype stress analyzer was found effective to perform a biaxial or triaxial stress analysis. (author)

X-ray stress measurement of ferritic steel using fourier analysis of Debye-Scherrer ring

International Nuclear Information System (INIS)

Fujimoto, Yohei; Sasaki, Toshihiko; Miyazaki, Toshiyuki

2015-01-01

In this study, X-ray stress measurements of ferritic steel based on Fourier analysis are conducted. Taira et al. developed the cosα method for X-ray stress measurements using a two-dimensional X-ray detector. Miyazaki et al. reported that the cosα method can be described more concisely by developing the Fourier series (the Fourier analysis method). The Fourier analysis method is expected to yield the stress measurement with an imperfect Debye-Scherrer ring and there is a possibility that the materials evaluation is different compared with the conventional method, that is, the sin 2 ψ method. In the Fourier analysis method, the strain measured by X-rays is developed as a Fourier series, and all the plane-stress components can be calculated from the Fourier series. In this study, the normal stress calculation was confirmed. In addition, the Fourier-analysis and cosα methods were used for X-ray stress measurements during a four-point bending test on a S45C test piece, and the effectiveness of the Fourier analysis method was confirmed. It was found that the experimental results from the Fourier analysis and cosα methods were nearly identical. In addition, the measurement accuracies of both the methods were equivalent. (author)

Thermal Stresses Analysis and Optimized TTP Processes to Achieved CNT-Based Diaphragm for Thin Panel Speakers

Directory of Open Access Journals (Sweden)

Feng-Min Lai

2016-01-01

Full Text Available Industrial companies popularly used the powder coating, classing, and thermal transfer printing (TTP technique to avoid oxidation on the metallic surface and stiffened speaker diaphragm. This study developed a TTP technique to fabricate a carbon nanotubes (CNTs stiffened speaker diaphragm for thin panel speaker. The self-developed TTP stiffening technique did not require a high curing temperature that decreased the mechanical property of CNTs. In addition to increasing the stiffness of diaphragm substrate, this technique alleviated the middle and high frequency attenuation associated with the smoothing sound pressure curve of thin panel speaker. The advantage of TTP technique is less harmful to the ecology, but it causes thermal residual stresses and some unstable connections between printed plates. Thus, this study used the numerical analysis software (ANSYS to analyze the stress and thermal of work piece which have not delaminated problems in transfer interface. The Taguchi quality engineering method was applied to identify the optimal manufacturing parameters. Finally, the optimal manufacturing parameters were employed to fabricate a CNT-based diaphragm, which was then assembled onto a speaker. The result indicated that the CNT-based diaphragm improved the sound pressure curve smoothness of the speaker, which produced a minimum high frequency dip difference (ΔdB value.

Transcriptomic identification of candidate genes involved in sunflower responses to chilling and salt stresses based on cDNA microarray analysis

Directory of Open Access Journals (Sweden)

Paniego Norma

2008-01-01

Full Text Available Abstract Background Considering that sunflower production is expanding to arid regions, tolerance to abiotic stresses as drought, low temperatures and salinity arises as one of the main constrains nowadays. Differential organ-specific sunflower ESTs (expressed sequence tags were previously generated by a subtractive hybridization method that included a considerable number of putative abiotic stress associated sequences. The objective of this work is to analyze concerted gene expression profiles of organ-specific ESTs by fluorescence microarray assay, in response to high sodium chloride concentration and chilling treatments with the aim to identify and follow up candidate genes for early responses to abiotic stress in sunflower. Results Abiotic-related expressed genes were the target of this characterization through a gene expression analysis using an organ-specific cDNA fluorescence microarray approach in response to high salinity and low temperatures. The experiment included three independent replicates from leaf samples. We analyzed 317 unigenes previously isolated from differential organ-specific cDNA libraries from leaf, stem and flower at R1 and R4 developmental stage. A statistical analysis based on mean comparison by ANOVA and ordination by Principal Component Analysis allowed the detection of 80 candidate genes for either salinity and/or chilling stresses. Out of them, 50 genes were up or down regulated under both stresses, supporting common regulatory mechanisms and general responses to chilling and salinity. Interestingly 15 and 12 sequences were up regulated or down regulated specifically in one stress but not in the other, respectively. These genes are potentially involved in different regulatory mechanisms including transcription/translation/protein degradation/protein folding/ROS production or ROS-scavenging. Differential gene expression patterns were confirmed by qRT-PCR for 12.5% of the microarray candidate sequences. Conclusion

A finite element elastic-plastic analysis of residual stresses due to clad welding in reactor vessels

International Nuclear Information System (INIS)

Buchalet, C.; Riccardella, P.C.

1972-01-01

Residual stresses due to weld deposited cladding on the inside of a typical Westinghouse pressurized water reactor vessel are investigated using an axisymmetric finite element elastic-plastic analysis. At the beginning of the analysis, one head of the weld cladding is assumed to lie on the reactor vessel wall at melting temperature (2600degF), but in the solid phase, while the vessel remains at 300degF (preheat temperature). All material properties used in the calculations are taken as temperature-dependent. Temperature profiles are obtained in the cladding and base metal at several discrete time intervals. These temperatures profiles are used to obtain the stress distribution for the same time intervals. Residual hoop tensile stresses of approximately 25 ksi were found to exist in the cladding. Peak tensile stresses in the hoop direction occur in the base metal near the cladding interface and reach a value of 60 ksi at the end of the transient. The tensile stress decreases very rapidly through the thickness of the base metal and becomes insignificant at about two inches from the inside surface. In order to lower residual stresses, a post-weld heat treatment is performed by uniformly heating the vessel to 1100degF, holding at that temperature for a specified period of time and then cooling slowly. The analysis shows that after this treatment, the peak stresses in the base metal decrease from 60 ksi to 32 ksi, while the stress in the cladding does not change significantly. (author)

Flux Balance Analysis of Escherichia coli under Temperature and pH Stress Conditions

KAUST Repository

Xu, Xiaopeng

2015-05-12

An interesting discovery in biology is that most genes in an organism are dispensable. That means these genes have minor effects on survival of the organism in standard laboratory conditions. One explanation of this discovery is that some genes play important roles in specific conditions and are essential genes under those conditions. E. coli is a model organism, which is widely used. It can adapt to many stress conditions, including temperature, pH, osmotic, antibiotic, etc. Underlying mechanisms and associated genes of each stress condition responses are usually different. In our analysis, we combined protein abundance data and mutant conditional fitness data into E. coli constraint-based metabolic models to study conditionally essential metabolic genes under temperature and pH stress conditions. Flux Balance Analysis was employed as the modeling method to analysis these data. We discovered lists of metabolic genes, which are E. coli dispensable genes, but conditionally essential under some stress conditions. Among these conditionally essential genes, atpA in low pH stress and nhaA in high pH stress found experimental evidences from previous studies. Our study provides new conditionally essential gene candidates for biologists to explore stress condition mechanisms.

Stress analysis of shear/compression test

International Nuclear Information System (INIS)

Nishijima, S.; Okada, T.; Ueno, S.

1997-01-01

Stress analysis has been made on the glass fiber reinforced plastics (GFRP) subjected to the combined shear and compression stresses by means of finite element method. The two types of experimental set up were analyzed, that is parallel and series method where the specimen were compressed by tilted jigs which enable to apply the combined stresses, to the specimen. Modified Tsai-Hill criterion was employed to judge the failure under the combined stresses that is the shear strength under the compressive stress. The different failure envelopes were obtained between the two set ups. In the parallel system the shear strength once increased with compressive stress then decreased. On the contrary in the series system the shear strength decreased monotonicly with compressive stress. The difference is caused by the different stress distribution due to the different constraint conditions. The basic parameters which control the failure under the combined stresses will be discussed

Mindfulness-based stress reduction as a stress management intervention for healthy individuals: a systematic review.

Science.gov (United States)

Sharma, Manoj; Rush, Sarah E

2014-10-01

Stress is a global public health problem with several negative health consequences, including anxiety, depression, cardiovascular disease, and suicide. Mindfulness-based stress reduction offers an effective way of reducing stress by combining mindfulness meditation and yoga in an 8-week training program. The purpose of this study was to look at studies from January 2009 to January 2014 and examine whether mindfulness-based stress reduction is a potentially viable method for managing stress. A systematic search from Medline, CINAHL, and Alt HealthWatch databases was conducted for all types of quantitative articles involving mindfulness-based stress reduction. A total of 17 articles met the inclusion criteria. Of the 17 studies, 16 demonstrated positive changes in psychological or physiological outcomes related to anxiety and/or stress. Despite the limitations of not all studies using randomized controlled design, having smaller sample sizes, and having different outcomes, mindfulness-based stress reduction appears to be a promising modality for stress management. © The Author(s) 2014.

Smartphone-Based Self-Assessment of Stress in Healthy Adult Individuals: A Systematic Review.

Science.gov (United States)

Þórarinsdóttir, Helga; Kessing, Lars Vedel; Faurholt-Jepsen, Maria

2017-02-13

Stress is a common experience in today's society. Smartphone ownership is widespread, and smartphones can be used to monitor health and well-being. Smartphone-based self-assessment of stress can be done in naturalistic settings and may potentially reflect real-time stress level. The objectives of this systematic review were to evaluate (1) the use of smartphones to measure self-assessed stress in healthy adult individuals, (2) the validity of smartphone-based self-assessed stress compared with validated stress scales, and (3) the association between smartphone-based self-assessed stress and smartphone generated objective data. A systematic review of the scientific literature was reported and conducted according to the Preferred Reporting Items for Systematic Reviews and Meta-Analysis (PRISMA) statement. The scientific databases PubMed, PsycINFO, Embase, IEEE, and ACM were searched and supplemented by a hand search of reference lists. The databases were searched for original studies involving healthy individuals older than 18 years, measuring self-assessed stress using smartphones. A total of 35 published articles comprising 1464 individuals were included for review. According to the objectives, (1) study designs were heterogeneous, and smartphone-based self-assessed stress was measured using various methods (e.g., dichotomized questions on stress, yes or no; Likert scales on stress; and questionnaires); (2) the validity of smartphone-based self-assessed stress compared with validated stress scales was investigated in 3 studies, and of these, only 1 study found a moderate statistically significant positive correlation (r=.4; P<.05); and (3) in exploratory analyses, smartphone-based self-assessed stress was found to correlate with some of the reported smartphone generated objective data, including voice features and data on activity and phone usage. Smartphones are being used to measure self-assessed stress in different contexts. The evidence of the validity of

Stress analysis of a rupture disk

International Nuclear Information System (INIS)

Werne, R.W.

1975-04-01

The results of an elastic stress analysis of the rupture disk for an internal pressure of 45.5 MPa (6600 psi) indicate that the maximum von Mises stresses occur in the membrane and are on the order of 483 to 690 MPa (70,000 psi). This far exceeds the yield of the membrane material of 207 MPa (30,000 psi). These high stresses are expected since the membrane is designed to burst at that design pressure. The von Mises stresses in the rest of the body are less than 138 MPa (20,000 psi). An elastic-plastic analysis of the membrane alone subjected to the 45.5 MPa (6600 psi) pressure indicates that it becomes plastically unstable, i.e., it continues to deform under constant load. A second load case with a constant 6.9 MPa (1000 psi) pressure throughout the entire body (i.e., after release of pressure by burst of the membrane) was analyzed. The results indicate that the elastic von Mises stresses are less than 26.7 MPa (3880 psi) throughout the body. (U.S.)

Boundary element analysis of stress singularity in dissimilar metals by friction welding

International Nuclear Information System (INIS)

Chung, N. Y.; Park, C. H.

2012-01-01

Friction welded dissimilar metals are widely applied in automobiles, rolling stocks, machine tools, and various engineering fields. Dissimilar metals have several advantages over homogeneous metals, including high strength, material property, fatigue endurance, impact absorption, high reliability, and vibration reduction. Due to the increased use of these metals, understanding their behavior under stress conditions is necessary, especially the analysis of stress singularity on the interface of friction-welded dissimilar metals. To establish a strength evaluation method and a fracture criterion, it is necessary to analyze stress singularity on the interface of dissimilar metals with welded flashes by friction welding under various loads and temperature conditions. In this paper, a method analyzing stress singularity for the specimens with and without flashes set in friction welded dissimilar metals is introduced using the boundary element method. The stress singularity index (λ) and the stress singularity factor (Γ) at the interface edge are computed from the stress analysis results. The shape and flash thickness, interface length, residual stress, and load are considered in the computation. Based on these results, the variations of interface length (c) and the ratio of flash thickness (t2 t1) greatly influence the stress singularity factors at the interface edge of friction welded dissimilar metals. The stress singularity factors will be a useful fracture parameter that considers stress singularity on the interface of dissimilar metals

Stress analysis and probabilistic assessment of multi-layer SiC-based accident tolerant nuclear fuel cladding

Energy Technology Data Exchange (ETDEWEB)

Stone, J.G., E-mail: Joshua.Stone@ga.com; Schleicher, R.; Deck, C.P.; Jacobsen, G.M.; Khalifa, H.E.; Back, C.A.

2015-11-15

Silicon carbide (SiC) fiber, SiC matrix composites (SiC/SiC) are being considered as a cladding material for light water reactors in order to improve safety performance. Engineered, multi-layer cladding designs consisting of both monolithic SiC (mSiC) and SiC/SiC have been examined as promising concepts to meet both strength and impermeability requirements. A new model has been developed to calculate stresses and failure probabilities for multi-layer cladding consisting of SiC-based materials in reactor operating conditions. The results show that stresses in SiC-based cladding are dominated by temperature-dependent irradiation-induced swelling, with the largest stresses occurring during the cold shutdown conditions. Failure probabilities are driven by the resulting tensile stresses at the cladding inner wall, while the outer wall is subject to compressive stresses. This indicates that the inner SiC/SiC, outer mSiC concept has the lowest failure probability, as the pseudo-plastic deformation of the composite reduces tensile loading and the compressed monolith provides a reliable, impermeable barrier to fission product release.

Finite Element Optimised Back Analysis of In Situ Stress Field and Stability Analysis of Shaft Wall in the Underground Gas Storage

Directory of Open Access Journals (Sweden)

Yifei Yan

2016-01-01

Full Text Available A novel optimised back analysis method is proposed in this paper. The in situ stress field of an underground gas storage (UGS reservoir in a Turkey salt cavern is analysed by the basic theory of elastic mechanics. A finite element method is implemented to optimise and approximate the objective function by systematically adjusting boundary loads. Optimising calculation is performed based on a novel method to reduce the error between measurement and calculation as much as possible. Compared with common back analysis methods such as regression method, the method proposed can further improve the calculation precision. By constructing a large circular geometric model, the effect of stress concentration is eliminated and a minimum difference between computed and measured stress can be guaranteed in the rectangular objective region. The efficiency of the proposed method is investigated and confirmed by its capability on restoring in situ stress field, which agrees well with experimental results. The characteristics of stress distribution of chosen UGS wells are obtained based on the back analysis results and by applying the corresponding fracture criterion, the shaft walls are proven safe.

Modeling and Analysis of a Combined Stress-Vibration Fiber Bragg Grating Sensor.

Science.gov (United States)

Yao, Kun; Lin, Qijing; Jiang, Zhuangde; Zhao, Na; Tian, Bian; Shi, Peng; Peng, Gang-Ding

2018-03-01

A combined stress-vibration sensor was developed to measure stress and vibration simultaneously based on fiber Bragg grating (FBG) technology. The sensor is composed of two FBGs and a stainless steel plate with a special design. The two FBGs sense vibration and stress and the sensor can realize temperature compensation by itself. The stainless steel plate can significantly increase sensitivity of vibration measurement. Theoretical analysis and Finite Element Method (FEM) were used to analyze the sensor's working mechanism. As demonstrated with analysis, the obtained sensor has working range of 0-6000 Hz for vibration sensing and 0-100 MPa for stress sensing, respectively. The corresponding sensitivity for vibration is 0.46 pm/g and the resulted stress sensitivity is 5.94 pm/MPa, while the nonlinearity error for vibration and stress measurement is 0.77% and 1.02%, respectively. Compared to general FBGs, the vibration sensitivity of this sensor is 26.2 times higher. Therefore, the developed sensor can be used to concurrently detect vibration and stress. As this sensor has height of 1 mm and weight of 1.15 g, it is beneficial for minimization and integration.

Analysis of crack opening stresses for center- and edge-crack tension specimens

Directory of Open Access Journals (Sweden)

Tong Di-Hua

2014-04-01

Full Text Available Accurate determination of crack opening stress is of central importance to fatigue crack growth analysis and life prediction based on the crack-closure model. This paper studies the crack opening behavior for center- and edge-crack tension specimens. It is found that the crack opening stress is affected by the crack tip element. By taking the crack tip element into account, a modified crack opening stress equation is given for the center-crack tension specimen. Crack surface displacement equations for an edge crack in a semi-infinite plate under remote uniform tension and partially distributed pressure are derived by using the weight function method. Based on these displacements, a crack opening stress equation for an edge crack in a semi-infinite plate under uniform tension has been developed. The study shows that the crack opening stress is geometry-dependent, and the weight function method provides an effective and reliable tool to deal with such geometry dependence.

New fatigue damage analysis of complex engineering components based on FEM

International Nuclear Information System (INIS)

Ott, W.

1987-05-01

A new type of fatigue damage analysis for multiaxial elastoplastic conditions based on a three-dimensional finite element analysis has been developed. The analysis includes the material model after Mroz. The fatigue life evaluation in the critical areas is based on plastic work at these locations. The proposed damage concept can be applied to arbitrary multiaxial stress-strain paths. For the evaluation of the damage cycles in terms of closed stress-strain hysteresis loops are not required. The damage is determined on the basis of uniaxial material data (stress-strain curve, life to crack iniation curve). (orig./HP) [de

Evaluation of Tire/Surfacing/Base Contact Stresses and Texture Depth

Directory of Open Access Journals (Sweden)

W.J.vdM. Steyn

2015-03-01

Full Text Available Tire rolling resistance has a major impact on vehicle fuel consumption. Rolling resistance is the loss of energy due to the interaction between the tire and the pavement surface. This interaction is a complicated combination of stresses and strains which depend on both tire and pavement related factors. These include vehicle speed, vehicle weight, tire material and type, road camber, tire inflation pressure, pavement surfacing texture etc. In this paper the relationship between pavement surface texture depth and tire/surfacing contact stress and area is investigated. Texture depth and tire/surfacing contact stress were measured for a range of tire inflation pressures on five different pavement surfaces. In the analysis the relationship between texture and the generated contact stresses as well as the contact stress between the surfacing and base layer are presented and discussed, and the anticipated effect of these relationships on the rolling resistance of vehicles on the surfacings, and subsequent vehicle fuel economy discussed.

Influence of solder joint length to the mechanical aspect during the thermal stress analysis

Science.gov (United States)

Tan, J. S.; Khor, C. Y.; Rahim, Wan Mohd Faizal Wan Abd; Ishak, Muhammad Ikman; Rosli, M. U.; Jamalludin, Mohd Riduan; Zakaria, M. S.; Nawi, M. A. M.; Aziz, M. S. Abdul; Ani, F. Che

2017-09-01

Solder joint is an important interconnector in surface mount technology (SMT) assembly process. The real time stress, strain and displacement of the solder joint is difficult to observe and assess the experiment. To tackle these problems, simulation analysis was employed to study the von Mises stress, strain and displacement in the thermal stress analysis by using Finite element based software. In this study, a model of leadless electronic package was considered. The thermal stress analysis was performed to investigate the effect of the solder length to those mechanical aspects. The simulation results revealed that solder length gives significant effect to the maximum von Mises stress to the solder joint. Besides, changes in solder length also influence the displacement of the solder joint in the thermal environment. The increment of the solder length significantly reduces the von Mises stress and strain on the solder joint. Thus, the understanding of the physical parameter for solder joint is important for engineer prior to designing the solder joint of the electronic component.

Thermal stress analysis for fatigue damage evaluation at a mixing tee

International Nuclear Information System (INIS)

Kamaya, Masayuki; Nakamura, Akira

2011-01-01

Highlights: → Thermal stress and fatigue damage have been analyzed for a mixing tee. → Fatigue damage was accumulated near boundaries of the cold spot. → It was found that fatigue damage was brought about by fluctuation of cold spot. → Simple one-dimensional analysis could derive stress for fatigue evaluation. - Abstract: Fatigue cracks have been found at mixing tees where fluids of different temperature flow in. In this study, the thermal stress at a mixing tee was calculated by the finite element method using temperature transients obtained by a fluid dynamics simulation. The simulation target was an experiment for a mixing tee, in which cold water flowed into the main pipe from a branch pipe. The cold water flowed along the main pipe wall and caused a cold spot, at which the membrane stress was relatively large. Based on the evaluated thermal stress, the magnitude of the fatigue damage was assessed according to the linear damage accumulation rule and the rain-flow procedure. Precise distributions of the thermal stress and fatigue damage could be identified. Relatively large axial stress occurred downstream from the branch pipe due to the cold spot. The variation ranges of thermal stress and fatigue damage became large near the position 20 o from the symmetry line in the circumferential direction. The position of the cold spot changed slowly in the circumferential direction, and this was the main cause of the fatigue damage. The fatigue damage was investigated for various differences in the temperature between the main and branch pipes. Since the magnitude of accumulated damage increased abruptly when the temperature difference exceeded the value corresponding to the fatigue limit, it was suggested that the stress amplitude should be suppressed less than the fatigue limit. In the thermal stress analysis for fatigue damage assessment, it was found that the detailed three-dimensional structural analysis was not required. Namely, for the current case, a one

Stress Analysis for the Critical Metal Structure of Bridge Crane

Science.gov (United States)

Ling, Zhangwei; Wang, Min; Xia, Junfang; Wang, Songhua; Guo, Xiaolian

2018-01-01

Based on the type of connection between the main girder and end beam of electrical single beam crane, the finite element analysis model of a full portal crane was established. The stress distribution of the critical structure under different loading conditions was analyzed. The results shown that the maximum Mises stress and deflection of the main girder were within the allowable range. And the connecting location between end beam web and main girder had higher stress than other region, especially at the lower edge and upper edge of the end beam web and the area near the bolt hole of upper wing panel. Therefore it is important to inspect the connection status, the stress condition and the crack situation nearing connection location during the regular inspection process to ensure the safety of the connection between the main girder and end beam.

Interaction between early-life stress and FKBP5 gene variants in major depressive disorder and post-traumatic stress disorder: A systematic review and meta-analysis.

Science.gov (United States)

Wang, Qingzhong; Shelton, Richard C; Dwivedi, Yogesh

2018-01-01

Gene-environment interaction contributes to the risks of psychiatric disorders. Interactions between FKBP5 gene variants and early-life stress may enhance the risk not only for mood disorder, but also for a number of other behavioral phenotypes. The aim of the present study was to review and conduct a meta-analysis on the results from published studies examining interaction between FKBP5 gene variants and early-life stress and their associations with stress-related disorders such as major depression and PTSD. A literature search was conducted using PsychINFO and PubMed databases until May 2017. A total of 14 studies with a pooled total of 15109 participants met the inclusion criteria, the results of which were combined and a meta-analysis was performed using the differences in correlations as the effect measure. Based on literature, rs1360780, rs3800373, and rs9470080 SNPs were selected within the FKBP5 gene and systematic review was conducted. Based on the Comprehensive Meta-Analysis software, no publication bias was detected. Sensitivity analysis and credibility of meta-analysis results also indicated that the analyses were stable. The meta-analysis showed that individuals who carry T allele of rs1360780, C-allele of rs3800373 or T-allele of rs9470080 exposed to early-life trauma had higher risks for depression or PTSD. The effects of ethnicity, age, sex, and different stress measures were not examined due to limited sample size. These results provide strong evidence of interactions between FKBP5 genotypes and early-life stress, which could pose a significant risk factor for stress-associated disorders such as major depression and PTSD. Copyright © 2017 Elsevier B.V. All rights reserved.

PDX vacuum vessel stress analysis

International Nuclear Information System (INIS)

Nikodem, Z.D.

1975-01-01

A stress analysis of PDX vacuum vessel is described and the summary of results is presented. The vacuum vessel is treated as a toroidal shell of revolution subjected to an internal vacuum. The critical buckling pressure is calculated. The effects of the geometrical discontinuity at the juncture of toroidal shell head and cylindrical outside wall, and the concavity of the cylindrical wall are examined. An effect of the poloidal field coil supports and the vessel outside supports on the stress distribution in the vacuum vessel is determined. A method evaluating the influence of circular ports in the vessel wall on the stress level in the vessel is outlined

Analysis of stress and strain in a rotating disk mounted on a rigid shaft

Directory of Open Access Journals (Sweden)

Alexandrova Nelli N.

2006-01-01

Full Text Available The plane state of stress in an elastic-perfectly plastic isotropic rotating annular disk mounted on a rigid shaft is studied. The analysis of stresses, strains and displacements within the disk of constant thickness and density is based on the Mises yield criterion and its associated flow rule. It is observed that the plastic deformation is localized in the vicinity of the inner radius of the disk, and the disk of a sufficiently large outer radius never becomes fully plastic. The semi-analytical method of stress-strain analysis developed is illustrated by some numerical examples. .

Web-Based and Mobile Stress Management Intervention for Employees

DEFF Research Database (Denmark)

Heber, E.; Lehr, D.; Ebert, D. D.

2016-01-01

Background: Work-related stress is highly prevalent among employees and is associated with adverse mental health consequences. Web-based interventions offer the opportunity to deliver effective solutions on a large scale; however, the evidence is limited and the results conflicting. Objective......: This randomized controlled trial evaluated the efficacy of guided Web-and mobile-based stress management training for employees. Methods: A total of 264 employees with elevated symptoms of stress (Perceived Stress Scale-10, PSS-10 >= 22) were recruited from the general working population and randomly assigned...... to an Internet-based stress management intervention (iSMI) or waitlist control group. The intervention (GET. ON Stress) was based on Lazarus's transactional model of stress, consisted of seven sessions, and applied both well-established problem solving and more recently developed emotion regulation strategies...

X-ray stress analysis of residual stress gradients in surface layers of steel

International Nuclear Information System (INIS)

Ganev, N.; Kraus, I.; Gosmanova, G.; Pfeiffer, L.; Tietz, H.-D.

2001-01-01

The aim of the contribution is to present the theoretical possibilities of X-ray non-destructive identification of stress gradients within the penetration depth of used radiation and its utilization for experimental stress analysis. Practical usefullness of outlined speculations is illustrated with results of stress measurements on cut and shot-penned steel samples. (author)

Stress Analysis for Mobile Hot Cell Design

International Nuclear Information System (INIS)

Muhammad Hannan Bahrin; Anwar Abdul Rahman; Mohd Arif Hamzah

2015-01-01

Prototype and Plant Development Centre (PDC) is developing a Mobile Hot Cell (MHC) to handle and manage Spent High Activity Radioactive Sources (SHARS), such as teletherapy heads and dry irradiators. At present, there are two units of MHC in the world, one in South Africa and the other one in China. Malaysian Mobile MHC is developed by Malaysian Nuclear Agency with the assistance of IAEA expert, based on the design of South Africa and China, but with improved features. Stress analysis has been performed on the design to fulfill the safety requirement in MHC operation. This paper discusses the loading effect analysis from the radiation shielding materials to the MHC wall structure, roof supporting column and window structure. (author)

FLEXURAL STRESS ANALYSIS OF RIGID PAVEMENTS USING AXI-SYMMETRIC AND PLANE STRAIN FEM

Directory of Open Access Journals (Sweden)

V.A. Sawant

2017-11-01

Full Text Available The design of pavement involves a study of soils and paving materials, their response under load for different climatic conditions. In the present study, an attempt has been made to compare stresses predicted using two finite element analyses. First analysis is based on the twodimensional plane strain assumption where as in second approach axi-symmetric condition is assumed to consider three-dimensional behavior of rigid pavement. The results are compared with flexural stresses obtained from conventional Portland Cement Association method. The computed flexural stresses obtained from axi-symmetric condition are found to be in close agreement with PCA method. Results of plane strain analysis show a fair agreement after application of an appropriate multiplication factor

Finite element formulation for thermal stress analysis of thin reactor structures

International Nuclear Information System (INIS)

Kulak, R.F.; Kennedy, J.M.; Belytschko, T.B.

1978-01-01

This paper describes the formulation of a finite-element procedure for the thermal stress analysis of thin wall reactor components. A general temperature-dependent constituent relationship is derived from a Gibbs potential function and a temperature-dependent yield surface. This form of constitutive relationship is applicable to problems of small strain. A similar form of a hypoelastic-plastic type is also developed for large strains. The variation of the yield surface with temperature is based upon a temperature-dependent, work-hardening model. The model uses a temperature-equivalent stress-plastic strain diagram which is generated from isothermal unaxial stress-strain data. The above constitutive relationships are incorporated into two computer codes and a previously developed numerical algorithm is used with minor modifications. A set of problems is presented validating the thermal analysis capability of the computer codes to a variety of problem types. (Auth.)

Micromechanical combined stress analysis: MICSTRAN, a user manual

Science.gov (United States)

Naik, R. A.

1992-01-01

Composite materials are currently being used in aerospace and other applications. The ability to tailor the composite properties by the appropriate selection of its constituents, the fiber and matrix, is a major advantage of composite materials. The Micromechanical Combined Stress Analysis (MICSTRAN) code provides the materials engineer with a user-friendly personal computer (PC) based tool to calculate overall composite properties given the constituent fiber and matrix properties. To assess the ability of the composite to carry structural loads, the materials engineer also needs to calculate the internal stresses in the composite material. MICSTRAN is a simple tool to calculate such internal stresses with a composite ply under combined thermomechanical loading. It assumes that the fibers have a circular cross-section and are arranged either in a repeating square or diamond array pattern within a ply. It uses a classical elasticity solution technique that has been demonstrated to calculate accurate stress results. Input to the program consists of transversely isotropic fiber properties and isotropic matrix properties such as moduli, Poisson's ratios, coefficients of thermal expansion, and volume fraction. Output consists of overall thermoelastic constants and stresses. Stresses can be computed under the combined action of thermal, transverse, longitudinal, transverse shear, and longitudinal shear loadings. Stress output can be requested along the fiber-matrix interface, the model boundaries, circular arcs, or at user-specified points located anywhere in the model. The MICSTRAN program is Windows compatible and takes advantage of the Microsoft Windows graphical user interface which facilitates multitasking and extends memory access far beyond the limits imposed by the DOS operating system.

Stress Analysis of Composites.

Science.gov (United States)

1981-01-01

8217, Finite Elements in Nonlinear Mechanics, 1., 109-130, Tapir Publishers, Norway (1978). 9. A.J. Barnard and P.W. Sharman, ’Elastic-Plastic Analysis Using...Hybrid Stress Finite Elements,’ Finite Elements in Nonlinear Mechanics, 1, 131-148, Tapir Publishers Norway, (1978). ’.........Pian, ’Variational

ASME stress linearization and classification - a discussion based on a case study

International Nuclear Information System (INIS)

Miranda, Carlos A. de J.; Faloppa, Altair A.; Mattar Neto, Miguel; Fainer, Gerson

2011-01-01

The ASME code, specially in its Nuclear Division (Subsection NB - Class I Components), gives some recommendations to the structural analyst on how to perform the verifications required to prove the design as good as the by-analysis prevented failures modes. Each of these failure modes has specific stress limits which are established based on simple but conservative hypothesis like the material perfectly plastic behavior and the shell theory with its typical membrane and bending stresses with linear distribution along the thickness. Other detail to keep in mind is the code distinction between primary and secondary stresses (respectively, stress that came due to equilibrium and due to displacement compatibility). In general, the numerical models used in the analyses are developed with plane or 3D solid elements and due this fact no direct comparison with the code limits can be done and, besides that, the programs do not distinguish between primary and secondary stresses. Mostly, the later are produced due to the temperature variation but they also appear near discontinuities. Sometimes, this classification is not so clear or direct. To perform the required ASME Code verifications the analyst should obtain the membrane and bending stresses from the plane or 3-D model which is called stress linearization and, also, should classify them as primary and secondary. (The excess between the maximum stress at a point and the sum of these linearized values is called peak stress and is included in the fatigue verification.) This task, most of the time is not a simple one due to the nature of the involved load and/or the complex geometry under analysis. In fact, there are several studies discussing on how to perform these stress classification and linearization. The present paper shows a discussion on how to perform these verifications based on a generic geometry found in many plants, from petrochemical to nuclear, which emphasizes some of theses issues. (author)

ASME stress linearization and classification - a discussion based on a case study

Energy Technology Data Exchange (ETDEWEB)

Miranda, Carlos A. de J.; Faloppa, Altair A.; Mattar Neto, Miguel; Fainer, Gerson, E-mail: cmiranda@ipen.b, E-mail: afaloppa@ipen.b, E-mail: mmattar@ipen.b, E-mail: gfainer@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2011-07-01

The ASME code, specially in its Nuclear Division (Subsection NB - Class I Components), gives some recommendations to the structural analyst on how to perform the verifications required to prove the design as good as the by-analysis prevented failures modes. Each of these failure modes has specific stress limits which are established based on simple but conservative hypothesis like the material perfectly plastic behavior and the shell theory with its typical membrane and bending stresses with linear distribution along the thickness. Other detail to keep in mind is the code distinction between primary and secondary stresses (respectively, stress that came due to equilibrium and due to displacement compatibility). In general, the numerical models used in the analyses are developed with plane or 3D solid elements and due this fact no direct comparison with the code limits can be done and, besides that, the programs do not distinguish between primary and secondary stresses. Mostly, the later are produced due to the temperature variation but they also appear near discontinuities. Sometimes, this classification is not so clear or direct. To perform the required ASME Code verifications the analyst should obtain the membrane and bending stresses from the plane or 3-D model which is called stress linearization and, also, should classify them as primary and secondary. (The excess between the maximum stress at a point and the sum of these linearized values is called peak stress and is included in the fatigue verification.) This task, most of the time is not a simple one due to the nature of the involved load and/or the complex geometry under analysis. In fact, there are several studies discussing on how to perform these stress classification and linearization. The present paper shows a discussion on how to perform these verifications based on a generic geometry found in many plants, from petrochemical to nuclear, which emphasizes some of theses issues. (author)

Residual stress concerns in containment analysis

International Nuclear Information System (INIS)

Costantini, F.; Kulak, R. F.; Pfeiffer, P. A.

1997-01-01

The manufacturing of steel containment vessels starts with the forming of flat plates into curved plates. A steel containment structure is made by welding individual plates together to form the sections that make up the complex shaped vessels. The metal forming and welding process leaves residual stresses in the vessel walls. Generally, the effect of metal forming residual stresses can be reduced or virtually eliminated by thermally stress relieving the vesseL In large containment vessels this may not be practical and thus the residual stresses due to manufacturing may become important. The residual stresses could possibly tiect the response of the vessel to internal pressurization. When the level of residual stresses is significant it will affect the vessel's response, for instance the yielding pressure and possibly the failure pressure. The paper will address the effect of metal forming residual stresses on the response of a generic pressure vessel to internal pressurization. A scoping analysis investigated the effect of residual forming stresses on the response of an internally pressurized vessel. A simple model was developed to gain understanding of the mechanics of the problem. Residual stresses due to the welding process were not considered in this investigation

Influence of Stress Shape Function on Analysis of Contact Problem Using Hybrid Photoelasticity

International Nuclear Information System (INIS)

Shin, Dongchul; Hawong, Jaisug

2013-01-01

In this research, a study on stress shape functions was conducted to analyze the contact stress problem by using a hybrid photoelasticity. Because the contact stress problem is generally solved as a half-plane problem, the relationship between two analytical stress functions, which are compositions of the Airy stress function, was similar to one of the crack problem. However, this relationship in itself could not be used to solve the contact stress problem (especially one with singular points). Therefore, to analyze the contact stress problem more correctly, stress shape functions based on the condition of two contact end points had to be considered in the form of these two analytical stress functions. The four types of stress shape functions were related to the stress singularities at the two contact end points. Among them, the primary two types used for the analysis of an O-ring were selected, and their validities were verified in this work

Analysis of stresses on buried pipeline subjected to landslide based on numerical simulation and regression analysis

Energy Technology Data Exchange (ETDEWEB)

Han, Bing; Jing, Hongyuan; Liu, Jianping; Wu, Zhangzhong [PetroChina Pipeline RandD Center, Langfang, Hebei (China); Hao, Jianbin [School of Petroleum Engineering, Southwest Petroleum University, Chengdu, Sichuan (China)

2010-07-01

Landslides have a serious impact on the integrity of oil and gas pipelines in the tough terrain of Western China. This paper introduces a solving method of axial stress, which uses numerical simulation and regression analysis for the pipelines subjected to landslides. Numerical simulation is performed to analyze the change regularity of pipe stresses for the five vulnerability assessment indexes, which are: the distance between pipeline and landslide tail; the thickness of landslide; the inclination angle of landslide; the pipeline length passing through landslide; and the buried depth of pipeline. A pipeline passing through a certain landslide in southwest China was selected as an example to verify the feasibility and effectiveness of this method. This method has practical applicability, but it would need large numbers of examples to better verify its reliability and should be modified accordingly. Also, it only considers the case where the direction of the pipeline is perpendicular to the primary slip direction of the landslide.

Design of PH-based accelerated life testing plans under multiple-stress-type

International Nuclear Information System (INIS)

Elsayed, E.A.; Zhang Hao

2007-01-01

Accelerated life testing (ALT) is used to obtain failure time data quickly under high stress levels in order to predict product life performance under design stress conditions. Most of the previous work on designing ALT plans is focused on the application of a single stress. However, as components or products become more reliable due to technological advances, it becomes more difficult to obtain significant amount of failure data within reasonable amount of time using single stress only. Multiple-stress-type ALTs have been employed as a means of overcoming such difficulties. In this paper, we design optimum multiple-stress-type ALT plans based on the proportional hazards model. The optimum combinations of stresses and their levels are determined such that the variance of the reliability estimate of the product over a specified period of time is minimized. The use of the model is illustrated using numerical example, and sensitivity analysis shows that the resultant optimum ALT plan is robust to the deviation in model parameters

Numerical stress analysis of toroidal coil by three-dimensional finite element method

International Nuclear Information System (INIS)

Nishimura, Hidetomo; Shimamoto, Susumu

1977-10-01

A structure analysis program based on finite element method for toroidal coils, developed in JAERI, and its example application to a medium-size tokamak are described. In this application, the effects of material anisotropy, poloidal field and spring constant value were studied, and also the influence of toroidal coil failure on the peak stress. The following were revealed. The effect of anisotropy on the peak stress in reinforcement must be considered. The effect of poloidal field on the peak stress is small compared with that of toroidal field. The spring constant value between coil and support does not much influence the peak stress value, The peak stress in reinforcement rises with increasing number of failed coils. In the case of 2000 nodes on the structure, CPU time with the program is about 40 min. (auth.)

Probabilistic analysis of structures involving random stress-strain behavior

Science.gov (United States)

Millwater, H. R.; Thacker, B. H.; Harren, S. V.

1991-01-01

The present methodology for analysis of structures with random stress strain behavior characterizes the uniaxial stress-strain curve in terms of (1) elastic modulus, (2) engineering stress at initial yield, (3) initial plastic-hardening slope, (4) engineering stress at point of ultimate load, and (5) engineering strain at point of ultimate load. The methodology is incorporated into the Numerical Evaluation of Stochastic Structures Under Stress code for probabilistic structural analysis. The illustrative problem of a thick cylinder under internal pressure, where both the internal pressure and the stress-strain curve are random, is addressed by means of the code. The response value is the cumulative distribution function of the equivalent plastic strain at the inner radius.

Patient-specific AAA wall stress analysis: 99-percentile versus peak stress

NARCIS (Netherlands)

Speelman, L.; Bosboom, E.M.H.; Schurink, G.W.H.; Hellenthal, F.A.M.V.I.; Buth, J.; Breeuwer, M.; Jacobs, M.J.; Vosse, van de F.N.

2008-01-01

Objective Biomechanically, rupture of an Abdominal Aortic Aneurysm (AAA) occurs when the stress acting on the wall due to the blood pressure, exceeds the strength of the wall. Peak wall stress estimations, based on CT reconstruction, may be prone to observer variation. This study focuses on the

Self-guided internet-based and mobile-based stress management for employees

DEFF Research Database (Denmark)

Ebert, D. D.; Heber, E.; Berking, M.

2016-01-01

Objective This randomised controlled trial (RCT) aimed to evaluate the efficacy of a self-guided internet-based stress management intervention (iSMI) for employees compared to a 6-month wait-list control group (WLC) with full access for both groups to treatment as usual. M e t h o d A sample of 264...... of stressed employees. Internet-based self-guided interventions could be an acceptable, effective and potentially costeffective approach to reduce the negative consequences associated with work-related stress....

Development of an inelastic stress analysis code 'KINE-T' and its evaluations

International Nuclear Information System (INIS)

Kobatake, K.; Takahashi, S.; Suzuki, M.

1977-01-01

Referring to the ASME B and PVC Code Case 1592-7, the inelastic stress analysis is required for the designs of the class 1 components in elevated temperature if the results of the elastic stress analysis and/or simplified inelastic analysis do not satisfy the requirements. Authors programmed a two-dimensional axisymmetric inelastic analysis code 'KINE-T', and carried out its evaluations and an application. This FEM code is based on the incremental method and the following: elastic-plastic constitutive equation (yield condition of von Mises; flow rule of Prandtl-Reuss; Prager's hardening rule); creep constitutive equation (equation of state approach; flow rule of von Mises; strain hardening rule); the temperature dependency of the yield function is considered; solution procedure of the assembled stiffness matrix is the 'initial stress method'. After the completion of the programming, authors compared the output with not only theoretical results but also with those of the MARC code and the ANSYS code. In order to apply the code to the practical designing, authors settled a quasi-component two-dimensional axisymmetric model and a loading cycle (500 cycles). Then, an inelastic analysis and its integrity evaluation are carried out

Creep Rupture Life Prediction Based on Analysis of Large Creep Deformation

Directory of Open Access Journals (Sweden)

YE Wenming

2016-08-01

Full Text Available A creep rupture life prediction method for high temperature component was proposed. The method was based on a true stress-strain elastoplastic creep constitutive model and the large deformation finite element analysis method. This method firstly used the high-temperature tensile stress-strain curve expressed by true stress and strain and the creep curve to build materials' elastoplastic and creep constitutive model respectively, then used the large deformation finite element method to calculate the deformation response of high temperature component under a given load curve, finally the creep rupture life was determined according to the change trend of the responsive curve.The method was verified by durable test of TC11 titanium alloy notched specimens under 500 ℃, and was compared with the three creep rupture life prediction methods based on the small deformation analysis. Results show that the proposed method can accurately predict the high temperature creep response and long-term life of TC11 notched specimens, and the accuracy is better than that of the methods based on the average effective stress of notch ligament, the bone point stress and the fracture strain of the key point, which are all based on small deformation finite element analysis.

Free vibration analysis of embedded magneto-electro-thermo-elastic cylindrical nanoshell based on the modified couple stress theory

Science.gov (United States)

Ghadiri, Majid; Safarpour, Hamed

2016-09-01

In this paper, size-dependent effect of an embedded magneto-electro-elastic (MEE) nanoshell subjected to thermo-electro-magnetic loadings on free vibration behavior is investigated. Also, the surrounding elastic medium has been considered as the model of Winkler characterized by the spring. The size-dependent MEE nanoshell is investigated on the basis of the modified couple stress theory. Taking attention to the first-order shear deformation theory (FSDT), the modeled nanoshell and its equations of motion are derived using principle of minimum potential energy. The accuracy of the presented model is validated with some cases in the literature. Finally, using the Navier-type method, an analytical solution of governing equations for vibration behavior of simply supported MEE cylindrical nanoshell under combined loadings is presented and the effects of material length scale parameter, temperature changes, external electric potential, external magnetic potential, circumferential wave numbers, constant of spring, shear correction factor and length-to-radius ratio of the nanoshell on natural frequency are identified. Since there has been no research about size-dependent analysis MEE cylindrical nanoshell under combined loadings based on FSDT, numerical results are presented to be served as benchmarks for future analysis of MEE nanoshells using the modified couple stress theory.

Deciphering Stress State of Seismogenic Faults in Oklahoma and Kansas Based on High-resolution Stress Maps

Science.gov (United States)

Qin, Y.; Chen, X.; Haffener, J.; Trugman, D. T.; Carpenter, B.; Reches, Z.

2017-12-01

Induced seismicity in Oklahoma and Kansas delineates clear fault trends. It is assumed that fluid injection reactivates faults which are optimally oriented relative to the regional tectonic stress field. We utilized recently improved earthquake locations and more complete focal mechanism catalogs to quantitatively analyze the stress state of seismogenic faults with high-resolution stress maps. The steps of analysis are: (1) Mapping the faults by clustering seismicity using a nearest-neighbor approach, manually picking the fault in each cluster and calculating the fault geometry using principal component analysis. (2) Running a stress inversion with 0.2° grid spacing to produce an in-situ stress map. (3) The fault stress state is determined from fault geometry and a 3D Mohr circle. The parameter `understress' is calculated to quantify the criticalness of these faults. If it approaches 0, the fault is critically stressed; while understress=1 means there is no shear stress on the fault. Our results indicate that most of the active faults have a planar shape (planarity>0.8), and dip steeply (dip>70°). The fault trends are distributed mainly in conjugate set ranges of [50°,70°] and [100°,120°]. More importantly, these conjugate trends are consistent with mapped basement fractures in southern Oklahoma, suggesting similar basement features from regional tectonics. The fault length data shows a loglinear relationship with the maximum earthquake magnitude with an expected maximum magnitude range from 3.2 to 4.4 for most seismogenic faults. Based on 3D local Mohr circle, we find that 61% of the faults have low understress (0.5) are located within highest-rate injection zones and therefore are likely to be influenced by high pore pressure. The faults that hosted the largest earthquakes, M5.7 Prague and M5.8 Pawnee are critically stressed (understress 0.2). These differences may help in understanding earthquake sequences, for example, the predominantly aftershock

Stress Regression Analysis of Asphalt Concrete Deck Pavement Based on Orthogonal Experimental Design and Interlayer Contact

Science.gov (United States)

Wang, Xuntao; Feng, Jianhu; Wang, Hu; Hong, Shidi; Zheng, Supei

2018-03-01

A three-dimensional finite element box girder bridge and its asphalt concrete deck pavement were established by ANSYS software, and the interlayer bonding condition of asphalt concrete deck pavement was assumed to be contact bonding condition. Orthogonal experimental design is used to arrange the testing plans of material parameters, and an evaluation of the effect of different material parameters in the mechanical response of asphalt concrete surface layer was conducted by multiple linear regression model and using the results from the finite element analysis. Results indicated that stress regression equations can well predict the stress of the asphalt concrete surface layer, and elastic modulus of waterproof layer has a significant influence on stress values of asphalt concrete surface layer.

Stress analysis on a PWR pressure vessel support structure

International Nuclear Information System (INIS)

Cruz, J.R.B.; Mattar Neto, M.; Jesus Miranda, C.A. de.

1992-01-01

The paper presents the stress analysis of a research PWR vessel support structure. Different geometries and thermal boundary conditions are evaluated. The finite element analysis is performed using ANSYS program. The ASME Section III criteria are applied for the stress verification and the following points are discussed: stress classification and linearization; jurisdictional boundary between ASME Subsection NB (Class 1 Components) and Subsection NF (Component Supports). (author)

A review of creep analysis and design under multi-axial stress states

International Nuclear Information System (INIS)

Yao, H.-T.; Xuan Fuzhen; Wang Zhengdong; Tu Shantung

2007-01-01

The existence of multi-axial states of stress cannot be avoided in elevated temperature components. It is essential to understand the associated failure mechanisms and to predict the lifetime in practice. Although metal creep has been studied for about 100 years, many problems are still unsolved, in particular for those involving multi-axial stresses. In this work, a state-of-the-art review of creep analysis and engineering design is carried out, with particular emphasis on the effect of multi-axial stresses. The existing theories and creep design approaches are grouped into three categories, i.e., the classical plastic theory (CPT) based approach, the cavity growth mechanism (CGM) based approach and the continuum damage mechanics (CDM) based approach. Following above arrangements, the constitutive equations and design criteria are addressed. In the end, challenges on the precise description of the multi-axial creep behavior and then improving the strength criteria in engineering design are presented

Finite element analysis of interface stress between neutron absorption coating and chop disk

International Nuclear Information System (INIS)

Tang Changliang; Zhang Xiaozhang; Jiang Lei; Dai Xingjian

2012-01-01

The performance of disk chopper is directly affected by bond strength between neutron absorption coating and chop disk. Based on the finite element analysis software ANSYS, the interface stress distribution under high speed centrifugal load was calculated, which was to investigate the effects of coating's elastic modulus, poisson ratio and coating thickness on the interfacial stress distribution. The results show that soft and tough coating can reduce the peak stress effectively, and coating thickness reducing is helpful to avoid the plastic failure of opening in the disk under high speed centrifugal load. (authors)

Simultaneous analysis of residual stress and stress intensity factor in a resist after UV-nanoimprint lithography based on electron moiré fringes

International Nuclear Information System (INIS)

Wang, Qinghua; Kishimoto, Satoshi

2012-01-01

In this study, the residual stress in a resist (PAK01) film and the stress intensity factor (SIF) of an induced crack are simultaneously estimated during ultraviolet nanoimprint lithography (UV-NIL) based on electron moiré fringes. A micro grid in a triangular arrangement on the resist film fabricated by UV-NIL is directly used as the model grid. Electron moiré fringes formed by the interference between the fabricated grid and the electron scan beam are used to measure the displacement distribution around the tip of a crack induced by the residual stress in the resist. The SIF of the crack is estimated using a displacement extrapolation method. The residual strain fields and the corresponding residual stress in the resist film far from the crack are determined and analyzed. This method is effective for evaluating the grid quality fabricated by the UV-NIL technique. (paper)

Analysis of rock stress and rock stress measurements with application to Aespoe HRL

International Nuclear Information System (INIS)

Lundholm, Beatrice

2000-11-01

The process of choosing a site for a nuclear waste repository means that many aspects have to be taken into consideration. One of these is that the repository has to be mechanically stable for a long time. The mechanical stability of the rock is very difficult to determine. One of several factors, which determine the mechanical stability, is the virgin state of stress. The thesis project consists of two parts. In the first part the state of stress at Aespoe Hard Rock Laboratory had to be defined. This was done based on earlier rock stress measurements conducted during the years 1988 to 1997. Two different measurement techniques have been used, hydraulic fracturing and overcoring. During the overcoring two types of cells have been used, CSIRO HI-cell and a cell developed by the Swedish State Power Board (SSPB). In the second part of the project, investigation of the correlation between the stress and geological structures are made using numerical modelling tools such as FLAC, UDEC and 3DEC. The rock stress measurements using the hydraulic fracturing gave orientations of the horizontal stress that coincide with earlier hydraulic fracturing measurements conducted in Scandinavia. The magnitudes of rock stresses are slightly lower than the earlier reported stress magnitudes for the Scandinavian part of the earth crust. The rock stresses obtained from the overcoring resulted in higher stresses than what was predicted by the hydraulic fracturing measurements. However, the orientation of the maximum horizontal stresses coincides well between the two techniques. The orientation is also more or less constant with respect to increasing depth. The state of stress at Aespoe is defined by using the results from the hydraulic fracturing and the measurements conducted by SSPB-cell. The measurements from the SSPB-cell are used since these have a Poisson's ratio that corresponds well with the uniaxial tests of rock samples and since the measurements have been done at a distance from

Role stress amongst nurses at the workplace: concept analysis.

Science.gov (United States)

Riahi, Sanaz

2011-09-01

The present study explicates the concept of role stress amongst nurses through an analysis adopted from Walker and Avant; Strategies for Theory Construction in Nursing, 4th edn, Prentice Hall, New Jersey, NY. Role stress has become a significant problem amongst nurses and has created much distress leading to burnout among many in the nursing profession. It is significant to analyse the concept of role stress and its relative attributes and consequences, in order to recognize the necessary antecedents needed to create better conditions for nurses at the workplace. A modified method developed by Walker and Avant was used for this concept analysis. A model representing the concept of role stress was developed through careful consideration of the attributes, consequences, antecedents and empirical referents of role stress. The concept analysis of role stress among nurses at the workplace recognized the vulnerability of the nursing discipline towards burnout and distress in general. It is critical to be aware of the current state of health care and note the increased workload created for nurses. Nurses are at a greater vulnerability for role stress, making it imperative for health care organizations to critically evaluate and establish preventative measures for the concept of role stress. 2011 Blackwell Publishing Ltd.

Problems of stress analysis of fuelling machine head components

International Nuclear Information System (INIS)

Mathur, D.D.

1975-01-01

The problem of stress analysis of fuelling machine head components are discussed. To fulfil the functional requirements, the components are required to have certain shapes where stress problems cannot be matched to a catalogue of pre-determined solutions. The areas where complex systems of loading due to hydrostatic pressure, weight, moments and temperature gradients coupled with the intricate shapes of the components make it difficult to arrive at satisfactory solutions. Particularly, the analysis requirements of the magazine housing, end cover, gravloc clamps and centre support are highlighted. An experimental stress analysis programme together with a theoretical finite element analysis is perhaps the answer. (author)

X-ray stress analysis in textured polycrystalline materials

International Nuclear Information System (INIS)

Yokoyama, Ryouichi; Harada, Jimpei

2010-01-01

The relationship between stress and strain in polycrystalline materials with fibre texture is examined on the basis of the strain analysis in the constituent crystallites within the Reuss approximation. By introducing the symmetry of reciprocal lattices for the constituent crystallites, the physical meaning of taking an average of the strains observed by X-ray diffraction (XRD) is made clear. By using formulae obtained by the present treatment for the stress-strain relation in cubic specimens with fibre texture in the Laue classes m3-bar m hkl Bragg reflections with h≠k≠l split into doublets owing to the existence of crystallites with two different orientations under the stress field. This technique was confirmed by the profile analysis in XRD data observed for reflections of 222 and 420 in a cubic TiN thin film sputtered on a polyimide film. The technique of the stress analysis and its confirmation are introduced. (author)

Seismic response analysis of a piping system subjected to multiple support excitations in a base isolated NPP building

International Nuclear Information System (INIS)

Surh, Han-Bum; Ryu, Tae-Young; Park, Jin-Sung; Ahn, Eun-Woo; Choi, Chul-Sun; Koo, Ja Choon; Choi, Jae-Boong; Kim, Moon Ki

2015-01-01

Highlights: • Piping system in the APR 1400 NPP with a base isolation design is studied. • Seismic response of piping system in base isolated building are investigated. • Stress classification method is examined for piping subjected to seismic loading. • Primary stress of piping is reduced due to base isolation design. • Substantial secondary stress is observed in the main steam piping. - Abstract: In this study, the stress response of the piping system in the advanced power reactor 1400 (APR 1400) with a base isolation design subjected to seismic loading is addressed. The piping system located between the auxiliary building with base isolation and the turbine building with a fixed base is considered since it can be subjected to substantial relative support movement during seismic events. First, the support responses with respect to the base characteristic are investigated to perform seismic analysis for multiple support excitations. Finite element analyses are performed to predict the piping stress response through various analysis methods such as the response spectrum, seismic support movement and time history method. To separately evaluate the inertial effect and support movement effect on the piping stress, the stress is decomposed into a primary and secondary stress using the proposed method. Finally, influences of the base isolation design on the piping system in the APR 1400 are addressed. The primary stress based on the inertial loading is effectively reduced in a base isolation design, whereas a considerable amount of secondary stress is generated in the piping system connecting a base isolated building with a fixed base building. It is also confirmed that both the response spectrum analysis and seismic support movement analysis provide more conservative estimations of the piping stress compared to the time history analysis

Photoelastic stress analysis in mitred bend under internal pressure

International Nuclear Information System (INIS)

Sawa, Yoshiaki

1987-01-01

The stress analysis and stress relaxation in mitred bend subjected to internal pressure have been studied by means of the photoelastic stress freezing method. The experimental results show that stress concentration occurs in the wedge tip of the intersectional plane and it is considerably influenced by the bent angle. Then, the stress relaxation was obtained by planing the wedge tip. (author)

Performance-Based Rewards and Work Stress

Science.gov (United States)

Ganster, Daniel C.; Kiersch, Christa E.; Marsh, Rachel E.; Bowen, Angela

2011-01-01

Even though reward systems play a central role in the management of organizations, their impact on stress and the well-being of workers is not well understood. We review the literature linking performance-based reward systems to various indicators of employee stress and well-being. Well-controlled experiments in field settings suggest that certain…

contact stress analysis of involute spur gear by finite element method

African Journals Online (AJOL)

USER

section using C- programming. Bending stress analysis has been performed using finite element analysis with ANSYS software. Comparison of bending stress analysis has been performed for symmetric and asymmetric spur gear tooth at critical section. Mushin J. Jweeg, et.al. [7] used 2D contact stress FEA model to ...

Back-propagation neural network-based approximate analysis of true stress-strain behaviors of high-strength metallic material

International Nuclear Information System (INIS)

Doh, Jaeh Yeok; Lee, Jong Soo; Lee, Seung Uk

2016-01-01

In this study, a Back-propagation neural network (BPN) is employed to conduct an approximation of a true stress-strain curve using the load-displacement experimental data of DP590, a high-strength material used in automobile bodies and chassis. The optimized interconnection weights are obtained with hidden layers and output layers of the BPN through intelligent learning and training of the experimental data; by using these weights, a mathematical model of the material's behavior is suggested through this feed-forward neural network. Generally, the material properties from the tensile test cannot be acquired until the fracture regions, since it is difficult to measure the cross-section area of a specimen after diffusion necking. For this reason, the plastic properties of the true stress-strain are extrapolated using the weighted-average method after diffusion necking. The accuracies of BPN-based meta-models for predicting material properties are validated in terms of the Root mean square error (RMSE). By applying the approximate material properties, the reliable finite element solution can be obtained to realize the different shapes of the finite element models. Furthermore, the sensitivity analysis of the approximate meta-model is performed using the first-order approximate derivatives of the BPN and is compared with the results of the finite difference method. In addition, we predict the tension velocity's effect on the material property through a first-order sensitivity analysis.

Finite element analysis of maxillary bone stress caused by Aramany Class IV obturator prostheses.

Science.gov (United States)

Miyashita, Elcio Ricardo; Mattos, Beatriz Silva Câmara; Noritomi, Pedro Yoshito; Navarro, Hamilton

2012-05-01

The retention of an Aramany Class IV removable partial dental prosthesis can be compromised by a lack of support. The biomechanics of this obturator prosthesis result in an unusual stress distribution on the residual maxillary bone. This study evaluated the biomechanics of an Aramany Class IV obturator prosthesis with finite element analysis and a digital 3-dimensional (3-D) model developed from a computed tomography scan; bone stress was evaluated according to the load placed on the prosthesis. A 3-D model of an Aramany Class IV maxillary resection and prosthesis was constructed. This model was used to develop a finite element mesh. A 120 N load was applied to the occlusal and incisal platforms corresponding to the prosthetic teeth. Qualitative analysis was based on the scale of maximum principal stress; values obtained through quantitative analysis were expressed in MPa. Under posterior load, tensile and compressive stresses were observed; the tensile stress was greater than the compressive stress, regardless of the bone region, and the greatest compressive stress was observed on the anterior palate near the midline. Under an anterior load, tensile stress was observed in all of the evaluated bone regions; the tensile stress was greater than the compressive stress, regardless of the bone region. The Aramany Class IV obturator prosthesis tended to rotate toward the surgical resection when subjected to posterior or anterior loads. The amount of tensile and compressive stress caused by the Aramany Class IV obturator prosthesis did not exceed the physiological limits of the maxillary bone tissue. (J Prosthet Dent 2012;107:336-342). Copyright © 2012 The Editorial Council of the Journal of Prosthetic Dentistry. Published by Mosby, Inc. All rights reserved.

Thermal Stress FE Analysis of Large-scale Gas Holder Under Sunshine Temperature Field

Science.gov (United States)

Li, Jingyu; Yang, Ranxia; Wang, Hehui

2018-03-01

The temperature field and thermal stress of Man type gas holder is simulated by using the theory of sunshine temperature field based on ASHRAE clear-sky model and the finite element method. The distribution of surface temperature and thermal stress of gas holder under the given sunshine condition is obtained. The results show that the thermal stress caused by sunshine can be identified as one of the important factors for the failure of local cracked oil leakage which happens on the sunny side before on the shady side. Therefore, it is of great importance to consider the sunshine thermal load in the stress analysis, design and operation of large-scale steel structures such as the gas holder.

Normalized wall index specific and MRI-based stress analysis of atherosclerotic carotid plaques. A study comparing acutely symptomatic and asymptomatic patients

International Nuclear Information System (INIS)

Zhu, C.; Teng, Z.; Sadat, U.; Young, V.E.; Graves, M.J.; Gillard, J.H.; Li Zhiyong

2010-01-01

Biomechanical stresses play an important role in determining plaque stability. Quantification of these simulated stresses can be potentially used to assess plaque vulnerability and differentiate different patient groups. 54 asymptomatic and 45 acutely symptomatic patients underwent in vivo multicontrast magnetic resonance imaging (MRI) of the carotid arteries. Plaque geometry used for finite element analysis was derived from in vivo MRI at the sites of maximum and minimum plaque burden. In total, 198 slices were used for the computational simulations. A pre-shrink technique was used to refine the simulation. Maximum principle stress at the vulnerable plaque sites (id est (ie), critical stress) was extracted for the selected slices and a comparison was performed between the 2 groups. Critical stress in the slice with maximum plaque burden is significantly higher in acutely symptomatic patients as compared to asymptomatic patients (median, inter quartile range: 198.0 kPa (119.8-359.0 kPa) vs 138.4 kPa (83.8-242.6 kPa), P=0.04). No significant difference was found in the slice with minimum plaque burden between the 2 groups (196.7 kPa (133.3-282.7 kPa) vs 182.4 kPa (117.2-310.6 kPa), P=0.82). Acutely symptomatic carotid plaques have significantly high biomechanical stresses than asymptomatic plaques. This might be potentially useful for establishing a biomechanical risk stratification criteria based on plaque burden in future studies. (author)

Adherence to internet-based mobile-supported stress management

DEFF Research Database (Denmark)

Zarski, A C; Lehr, D.; Berking, M.

2016-01-01

of this study was to investigate the influence of different guidance formats (content-focused guidance, adherence-focused guidance, and administrative guidance) on adherence and to identify predictors of nonadherence in an Internet-based mobile-supported stress management intervention (ie, GET.ON Stress......) for employees. Methods: The data from the groups who received the intervention were pooled from three randomized controlled trials (RCTs) that evaluated the efficacy of the same Internet-based mobile-supported stress management intervention (N=395). The RCTs only differed in terms of the guidance format...... of the predictors significantly predicted nonadherence. Conclusions: Guidance has been shown to be an influential factor in promoting adherence to an Internet-based mobile-supported stress management intervention. Adherence-focused guidance, which included email reminders and feedback on demand, was equivalent...

The stress and strain analysis research of class 1 eqnipments

International Nuclear Information System (INIS)

Ye Yuanwu; Tang Long; Wang Yueying; Qi Min; Yu Huajin

2008-01-01

The class 1 equipment is very important in the nuclear device, in the design and testing process required to carry out their stress and strain analysis, so as to ensure their safety. There are two ways to get stress and strain analysis of the class 1 equipment, the theoretical and experimental methods. Through theoretical method can get the stress and strain of the class 1 equipment, so as to provide a basis for the design of the equipment; through the experimental method to verify the accuracy of the theoretical methods and provide a basis for the safety assessment of the equipment. The main ressel of CEFR (China Experimental Fast Reactor) is the class 1 equipment. In this paper, according to the stress and strain analysis research of CEFR main vessel, the theories and expperimental methods of nuclear class 1 equipments stress and strain analysis has been described. (authors)

PDX toroidal field coils stress analysis

International Nuclear Information System (INIS)

Nikodem, Z.D.; Smith, R.A.

1975-01-01

A method used in the stress analysis of the PDX toroidal field coil is developed. A multilayer coil design of arbitrary dimensions in the shape of either a circle or an oval is considered. The analytical model of the coil and the supporting coil case with connections to the main support structure is analyzed using the finite element technique. The three dimensional magnetic fields and the non-uniform body forces which are a loading condition on a coil due to toroidal and poloidal fields are calculated. The method of analysis permits rapid and economic evaluations of design changes in coil geometry as well as in coil support structures. Some results pertinent to the design evolution and their comparison are discussed. The results of the detailed stress analysis of the final coil design due to toroidal field, poloidal field and temperature loads are presented

Ductile failure analysis of defective API X65 pipes based on stress-modified fracture strain criterion

International Nuclear Information System (INIS)

Oh, Chang Kyun; Kim, Yun Jae; Baek, Jong Hyun; Kim, Young Pyo; Kim, Woo Sik

2006-01-01

A local failure criterion for the API X65 steel is applied to predict ductile failure of full-scale API X65 pipes with simulated corrosion and gouge defects under internal pressure. The local failure criterion is the stress-modified fracture strain for the API X65 steel as a function of the stress triaxiality (defined by the ratio of the hydrostatic stress to the effective stress). Based on detailed FE analyses with the proposed local failure criteria, burst pressures of defective pipes are estimated and compared with experimental data. The predicted burst pressures are in good agreement with experimental data. Noting that an assessment equation against the gouge defect is not yet available, parametric study is performed, from which a simple equation is proposed to predict burst pressure for API X65 pipes with gouge defects

Limit load and fully plastic stress analysis for circular notched plates and bars using fully plastic analysis

International Nuclear Information System (INIS)

Oh, Chang Kyun; Myung, Man Sik; Kim, Yun Jae; Park, Jin Moo

2005-01-01

For the last four decades, tension test of notched bars has been performed to investigate the effect of stress triaxiality on ductile fracture. To quantify the effect of the notch radius on stress triaxiality, the Bridgman equation is typically used. However, recent works based on detailed finite element analysis have shown that the Bridgman equation is not correct, possibly due to his assumption that strain is constant in the necked ligament. Up to present, no systematic work has been performed on fully plastic stress fields for notched bars in tension. This paper presents fully plastic results for tension of notched bars and plates in plane strain, via finite element limit analysis. The notch radius is systematically varied, covering both un-cracked and cracked cases. Comparison of plastic limit loads with existing solutions shows that existing solutions are accurate for notched plates, but not for notched bars. Accordingly new limit load solutions are given for notched bars. Variations of stress triaxiality with the notch radius and depth are also given, which again indicates that the Bridgman solution for notched bars is not correct and inaccuracy depends on the notch radius and depth

Transcriptome analysis of hexaploid hulless oat in response to salinity stress.

Directory of Open Access Journals (Sweden)

Bin Wu

Full Text Available Oat is a cereal crop of global importance used for food, feed, and forage. Understanding salinity stress tolerance mechanisms in plants is an important step towards generating crop varieties that can cope with environmental stresses. To date, little is known about the salt tolerance of oat at the molecular level. To better understand the molecular mechanisms underlying salt tolerance in oat, we investigated the transcriptomes of control and salt-treated oat using RNA-Seq.Using Illumina HiSeq 4000 platform, we generated 72,291,032 and 356,891,432 reads from non-stressed control and salt-stressed oat, respectively. Assembly of 64 Gb raw sequence data yielded 128,414 putative unique transcripts with an average length of 1,189 bp. Analysis of the assembled unigenes from the salt stressed and control libraries indicated that about 65,000 unigenes were differentially expressed at different stages. Functional annotation showed that ABC transporters, plant hormone signal transduction, plant-pathogen interactions, starch and sucrose metabolism, arginine and proline metabolism, and other secondary metabolite pathways were enriched under salt stress. Based on the RPKM values of assembled unigenes, 24 differentially expressed genes under salt stress were selected for quantitative RT-PCR validation, which successfully confirmed the results of RNA-Seq. Furthermore, we identified 18,039 simple sequence repeats, which may help further elucidate salt tolerance mechanisms in oat.Our global survey of transcriptome profiles of oat plants in response to salt stress provides useful insights into the molecular mechanisms underlying salt tolerance in this crop. These findings also represent a rich resource for further analysis of salt tolerance and for breeding oat with improved salt tolerance through the use of salt-related genes.

Estimation of the stress related to conservative scoliosis therapy: an analysis based on BSSQ questionnaires

Directory of Open Access Journals (Sweden)

Szulc Andrzej

2007-01-01

Full Text Available Abstract Background Adolescent girls treated with a brace for scoliosis are submitted to prolonged stress related to both the disease and the therapy. Currently proposed quality of life questionnaires are focused on the outcome of therapy. Bad Sobernheim Stress Questionnaire (BSSQ enables monitoring of patients being under treatment with a brace or exercises. The aim of the study was to assess the stress level in conservatively managed scoliotic girls using BSSQ. Materials and methods 111 girls, aged 14,2 ± 2,2 years, mean Cobb angle of the primary curve 42,8° ± 17,0° and mean Bunnell angle of 11,4° ± 4,5° were examined with two versions of BSSQ (Deformity and Brace. The analysis considered the type of treatment, curve location, correlation of the total score with age, Cobb angle and Bunnell rotation angle. Results The BSSQ Deformity revealed the median of 17 points in patients managed with exercises (from 4 to 24 points, 18 in patients managed with a brace (from 8 to 24 points and 12 in patients before surgery (from 3 to 21 points. Braced patients who completed both questionnaires (n = 50 revealed significantly higher score with BSSQ Deformity (median = 18 comparing to BSSQ Brace (median = 9. There was a correlation between the total score of BSSQ Deformity and the Cobb angle (r = -0,34, Bunnell primary curve rotation (r = -0,34 and Bunnell sum of rotation (r = -0,33 but not with the age of patients. Conclusion Scoliotic adolescents managed with exercises and brace suffered little stress from the deformity. The brace increased the level of stress over the stress induced by the deformity. The stress level correlated with clinical deformity (Bunnell angle, radiological deformity (Cobb angle and the type of treatment (exercises, bracing, surgery. Bad Sobernheim Stress Questionnaires are simple and helpful in the management of girls treated conservatively for idiopathic scoliosis.

Re-analysis of fatigue data for welded joints using the notch stress approach

DEFF Research Database (Denmark)

Pedersen, Mikkel Melters; Mouritsen, Ole Ø.; Hansen, Michael Rygaard

2010-01-01

Experimental fatigue data for welded joints have been collected and subjected to re-analysis using the notch stress approach according to IIW recommendations. This leads to an overview regarding the reliability of the approach, based on a large number of results (767 specimens). Evidently......-welded joints agree quite well with the FAT 225 curve; however a reduction to FAT 200 is suggested in order to achieve approximately the same safety as observed in the nominal stress approach....

Stress and burnout in residents: impact of mindfulness-based resilience training

Directory of Open Access Journals (Sweden)

Goldhagen BE

2015-08-01

Full Text Available Brian E Goldhagen,1 Karen Kingsolver,2 Sandra S Stinnett,1 Jullia A Rosdahl1 1Department of Ophthalmology, 2Department of Family and Community Medicine, Duke University Medical Center, Durham, NC, USABackground and objective: Stress and burnout impact resident physicians. This prospective study tests the hypothesis that a mindfulness-based resilience intervention would decrease stress and burnout in residents.Methods: Resident physicians from the Departments of Family Medicine, Psychiatry, and Anesthesia at Duke University, Durham, NC, USA, participated in two or three 1-hour sessions of mindfulness-based resilience activities, which introduced mindful-awareness and included practical exercises for nurturing resilience. Anonymous surveys were distributed before (completed by 47 residents and after the intervention (both completed by 30 residents; a follow-up survey was distributed 1 month later (seven residents completed all three surveys. The survey included the Depression Anxiety Stress Scale, 21-question version (DASS-21, the Oldenburg Burnout Inventory, the Mindful Attention Awareness Scale, and ten questions from the Cognitive Failures Questionnaire.Results: At baseline, most residents’ scores were in the normal range with respect to stress; however, female residents had higher DASS-21 scores than male residents (31.7, females vs 18.4, males; P=0.002. Most residents’ burnout scores were in the abnormal range, both with respect to exhaustion (38/47 residents, subscore ≥2.25 and disengagement (37/47 residents, subscore ≥2.1. Higher perceived levels of stress correlated with the instruments. Analysis of the surveys before and after the intervention showed no significant short-term change in stress, burnout, mindful-awareness, or cognitive failure. There was a trend for females and post-medical school graduate year 1 and 2 (PGY1 and PGY2 residents to have a reduction in DASS-21 scores after intervention. There was also a trend of

Analysis of Stress-Responsive Gene Expression in Cultivated and Weedy Rice Differing in Cold Stress Tolerance.

Directory of Open Access Journals (Sweden)

Caroline Borges Bevilacqua

Full Text Available Rice (Oryza sativa L. cultivars show impairment of growth in response to environmental stresses such as cold at the early seedling stage. Locally adapted weedy rice is able to survive under adverse environmental conditions, and can emerge in fields from greater soil depth. Cold-tolerant weedy rice can be a good genetic source for developing cold-tolerant, weed-competitive rice cultivars. An in-depth analysis is presented here of diverse indica and japonica rice genotypes, mostly weedy rice, for cold stress response to provide an understanding of different stress adaptive mechanisms towards improvement of the rice crop performance in the field. We have tested a collection of weedy rice genotypes to: 1 classify the subspecies (ssp. grouping (japonica or indica of 21 accessions; 2 evaluate their sensitivity to cold stress; and 3 analyze the expression of stress-responsive genes under cold stress and a combination of cold and depth stress. Seeds were germinated at 25°C at 1.5- and 10-cm sowing depth for 10d. Seedlings were then exposed to cold stress at 10°C for 6, 24 and 96h, and the expression of cold-, anoxia-, and submergence-inducible genes was analyzed. Control plants were seeded at 1.5cm depth and kept at 25°C. The analysis revealed that cold stress signaling in indica genotypes is more complex than that of japonica as it operates via both the CBF-dependent and CBF-independent pathways, implicated through induction of transcription factors including OsNAC2, OsMYB46 and OsF-BOX28. When plants were exposed to cold + sowing depth stress, a complex signaling network was induced that involved cross talk between stresses mediated by CBF-dependent and CBF-independent pathways to circumvent the detrimental effects of stresses. The experiments revealed the importance of the CBF regulon for tolerance to both stresses in japonica and indica ssp. The mechanisms for cold tolerance differed among weedy indica genotypes and also between weedy indica and

Calculation of elastic-plastic strain ranges for fatigue analysis based on linear elastic stresses

International Nuclear Information System (INIS)

Sauer, G.

1998-01-01

Fatigue analysis requires that the maximum strain ranges be known. These strain ranges are generally computed from linear elastic analysis. The elastic strain ranges are enhanced by a factor K e to obtain the total elastic-plastic strain range. The reliability of the fatigue analysis depends on the quality of this factor. Formulae for calculating the K e factor are proposed. A beam is introduced as a computational model for determining the elastic-plastic strains. The beam is loaded by the elastic stresses of the real structure. The elastic-plastic strains of the beam are compared with the beam's elastic strains. This comparison furnishes explicit expressions for the K e factor. The K e factor is tested by means of seven examples. (orig.)

Development of a stress sensor based on the piezoelectric lead zirconate titanate for impact stress measurement

Science.gov (United States)

Liu, Yiming; Xu, Bin; Li, Lifei; Li, Bing

2012-04-01

The measurement of stress of concrete structures under impact loading and other strong dynamic loadings is crucial for the monitoring of health and damage detection. Due to its main advantages including availability, extremely high rigidity, high natural frequency, wide measuring range, high stability, high reproducibility, high linearity and wide operating temperature range, piezoelectric (Lead Zirconate Titanate, PZT) ceramic materials has been a widely used smart material for both sensing and actuation for monitoring and control in engineering structures. In this paper, a kind of stress sensor based on piezoelectric ceramics for impact stress measuring of concrete structures is developed. Because the PZT is fragile, in order to employ it for the health monitoring of concrete structures, special handling and treatment should be taken to protect the PZT and to make it survive and work properly in concrete. The commercially available PZT patch with lead wires is first applied with an insulation coating to prevent water and moisture damage, and then is packaged by jacketing it by two small precasted cylinder concrete blocks with enough strength to form a smart aggregate (SA). The employed PZT patch has a dimension of 10mm x 10mm x 0.3mm. In order to calibrate the PZT based stress sensor for impact stress measuring, a dropping hammer was designed and calibration test on the sensitivity of the proposed transducer was carried out with an industry charge amplifier. The voltage output of the stress sensor and the impact force under different free falling heights and impact mass were recorded with a high sampling rate data acquisition system. Based on the test measurements, the sensibility of the PZT based stress sensor was determined. Results show that the output of the PZT based stress sensor is proportional to the stress level and the repeatability of the measurement is very good. The self-made piezoelectric stress sensor can be easily embedded in concrete and provide

Photostress analysis of stress-induced martensite phase transformation in superelastic NiTi

International Nuclear Information System (INIS)

Katanchi, B.; Choupani, N.; Khalil-Allafi, J.; Baghani, M.

2017-01-01

Phase transformation in shape memory alloys is the most important factor in their unique behavior. In this paper, the formation of stress induced martensite phase transformation in a superelastic NiTi (50.8% Ni) shape memory alloy was investigated by using the photo-stress method. First, the material's fabrication procedure has been described and then the material was studied using the metallurgical tests such as differential scanning calorimetry and X-ray diffraction to characterize the material features and the mechanical tensile test to investigate the superelastic behavior. As a new method in observation of the phase transformation, photo-stress pictures showed the formation of stress induced martensite in a superelastic dog-bone specimen during loading and subsequently it's disappearing during unloading. Finally, finite element analysis was implemented using the constitutive equations derived based on the Boyd-Lagoudas phenomenological model.

Photostress analysis of stress-induced martensite phase transformation in superelastic NiTi

Energy Technology Data Exchange (ETDEWEB)

Katanchi, B. [Mechanical Engineering Faculty, Sahand University of Technology, Tabriz (Iran, Islamic Republic of); Choupani, N., E-mail: choupani@sut.ac.ir [Mechanical Engineering Faculty, Sahand University of Technology, Tabriz (Iran, Islamic Republic of); Khalil-Allafi, J. [Research Center for Advance Materials, Faculty of Materials Engineering, Sahand University of Technology, Tabriz (Iran, Islamic Republic of); Baghani, M. [School of Mechanical Engineering, College of Engineering, University of Tehran (Iran, Islamic Republic of)

2017-03-14

Phase transformation in shape memory alloys is the most important factor in their unique behavior. In this paper, the formation of stress induced martensite phase transformation in a superelastic NiTi (50.8% Ni) shape memory alloy was investigated by using the photo-stress method. First, the material's fabrication procedure has been described and then the material was studied using the metallurgical tests such as differential scanning calorimetry and X-ray diffraction to characterize the material features and the mechanical tensile test to investigate the superelastic behavior. As a new method in observation of the phase transformation, photo-stress pictures showed the formation of stress induced martensite in a superelastic dog-bone specimen during loading and subsequently it's disappearing during unloading. Finally, finite element analysis was implemented using the constitutive equations derived based on the Boyd-Lagoudas phenomenological model.

ITER vacuum vessel dynamic stress analysis of a disruption

International Nuclear Information System (INIS)

Riemer, B.W.; Conner, D.L.; Strickler, D.J.; Williamson, D.E.

1994-01-01

Dynamic stress analysis of the International Thermonuclear Experimental Reactor vacuum vessel loaded by disruption forces was performed. The deformation and stress results showed strong inertial effects when compared to static analyses. Maximum stress predicted dynamically was 300 MPa, but stress shown by static analysis from loads at the same point in time reached only 80 MPa. The analysis also provided a reaction load history in the vessel's supports which is essential in evaluating support design. The disruption forces were estimated by assuming a 25-MA plasma current decaying at 1 MA/ms while moving vertically. In addition to forces developed within the vessel, vertical loadings from the first wall/strong back assemblies and the divertor were applied to the vessel at their attachment points. The first 50 natural modes were also determined. The first mode's frequency was 6.0 Hz, and its shape is characterized by vertical displacement of the vessel inner leg. The predicted deformation of the vessel appeared similar to its first mode shape combined with radial contraction. Kinetic energy history from the analysis also correlated with the first mode frequency

Stress Analysis of Non-Ferrous Metals Welds by Numerical Simulation

Directory of Open Access Journals (Sweden)

Kravarikova Helena

2017-01-01

Full Text Available Thermal energy welded material unevenly heated and thus supports the creation of tension. During the fusing process welding transient tensions generated in the welded material. Generation of the transient tensions depends on the thermal expansion and fixed permanently welded parts. Tensions are the result of the interaction of material particles. For welded parts and constructions it is necessary to know the size and direction of application of tensions. The emerging tensions can cause local change or a total deformation of welded materials. Deformations and residual stresses impair the performance of a welded construction, reduces the stability of the parts. To reduce or eliminate of action or a screening direction stresses and strains it is necessary to know the mechanism of their emergence. It is now possible to examine the emergence of tensions numerical experiments on any model using numerical simulation using FEM. Results of numerical experiment is the analysis of stress and deformation course. In the plane the tension it divided into normal σ and τ tangential folders. Decomposition stress on components simplifies the stress analysis. The results obtained from numerical analysis are correct to predict the stress distribution and size. The paper presents the results of numerical experiments stress analysis solutions fillet welds using FEM numerical simulation of welding of non-ferrous metals.

Folsom Dam Outlet Works Modification Project; Simplified Three-Dimensional Stress Analysis of Monolith 12

National Research Council Canada - National Science Library

Matheu, Enrique E; Garner, Sharon B

2005-01-01

This report presents a finite-element stress analysis of monolith 12 conducted to assess any potential adverse effects caused by the proposed dimensions of the air vent near the base of the spillway pier wall...

Study on the Leak Rate Estimation of SG Tubes and Residual Stress Estimation based on Plastic Deformation

Energy Technology Data Exchange (ETDEWEB)

Kim, Young Jin; Chang, Yoon Suk; Lee, Dock Jin; Lee, Tae Rin; Choi, Shin Beom; Jeong, Jae Uk; Yeum, Seung Won [Sungkyunkwan University, Seoul (Korea, Republic of)

2009-02-15

In this research project, a leak rate estimation model was developed for steam generator tubes with through wall cracks. The modelling was based on the leak data from 23 tube specimens. Also, the procedure of finite element analysis was developed for residual stress calculation of dissimilar metal weld in a bottom mounted instrumentation. The effect of geometric variables related with the residual stress in penetration weld part was investigated by using the developed analysis procedure. The key subjects dealt in this research are: 1. Development of leak rate estimation model for steam generator tubes with through wall cracks 2. Development of the program which can perform the structure and leakage integrity evaluation for steam generator tubes 3. Development of analysis procedure for bottom mounted instrumentation weld residual stress 4. Analysis on the effects of geometric variables on weld residual stress It is anticipated that the technologies developed in this study are applicable for integrity estimation of steam generator tubes and weld part in NPP.

Finite element stress analysis of brick-mortar masonry under ...

African Journals Online (AJOL)

Stress analysis of a brick-mortar couplet as a substitute for brick wall structure has been performed by finite element method, and algorithm for determining the element stiffness matrix for a plane stress problem using the displacement approach was developed. The nodal displacements were derived for the stress in each ...

Proteomic analysis of cold stress responses in tobacco seedlings ...

African Journals Online (AJOL)

Cold stress is one of the major abiotic stresses limiting the productivity and the geographical distribution of many important crops. To gain a better understanding of cold stress responses in tobacco (Nicotiana tabacum), we carried out a comparative proteomic analysis. Five-week-old tobacco seedlings were treated at 4°C ...

Quantitative Proteomics for the Comprehensive Analysis of Stress Responses of Lactobacillus paracasei subsp. paracasei F19.

Science.gov (United States)

Schott, Ann-Sophie; Behr, Jürgen; Geißler, Andreas J; Kuster, Bernhard; Hahne, Hannes; Vogel, Rudi F

2017-10-06

Lactic acid bacteria are broadly employed as starter cultures in the manufacture of foods. Upon technological preparation, they are confronted with drying stress that amalgamates numerous stress conditions resulting in losses of fitness and survival. To better understand and differentiate physiological stress responses, discover general and specific markers for the investigated stress conditions, and predict optimal preconditioning for starter cultures, we performed a comprehensive genomic and quantitative proteomic analysis of a commonly used model system, Lactobacillus paracasei subsp. paracasei TMW 1.1434 (isogenic with F19) under 11 typical stress conditions, including among others oxidative, osmotic, pH, and pressure stress. We identified and quantified >1900 proteins in triplicate analyses, representing 65% of all genes encoded in the genome. The identified genes were thoroughly annotated in terms of subcellular localization prediction and biological functions, suggesting unbiased and comprehensive proteome coverage. In total, 427 proteins were significantly differentially expressed in at least one condition. Most notably, our analysis suggests that optimal preconditioning toward drying was predicted to be alkaline and high-pressure stress preconditioning. Taken together, we believe the presented strategy may serve as a prototypic example for the analysis and utility of employing quantitative-mass-spectrometry-based proteomics to study bacterial physiology.

Mindfulness Based Stress Reduction for Academic Evaluation Anxiety: A Naturalistic Longitudinal Study

Science.gov (United States)

Dundas, Ingrid; Thorsheim, Torbjørn; Hjeltnes, Aslak; Binder, Per Einar

2016-01-01

Mindfulness based stress reduction (MBSR) for academic evaluation anxiety and self-confidence in 70 help-seeking bachelor's and master's students was examined. A repeated measures analysis of covariance on the 46 students who completed pretreatment and posttreatment measures (median age = 24 years, 83% women) showed that evaluation anxiety and…

Simplified calculation of thermal stresses - on the reduction of effort in the stress analysis of reactor components

International Nuclear Information System (INIS)

Karow, K.

1984-01-01

The fatigue behaviour of reactor components is predominantly determined from the in-service thermal stresses. The calculation of such stresses for a number of temperature transients in the adjacent fluid may be expensive, particularly with complicated structures. Under certain conditions this expense can be reduced considerably with the aid of a rule, which permits interpolation of thermal stresses from known reference values instead of calculation. This paper presents the derivation and method of application of this interpolation rule. The derivation procedure is based on well-known proportionalities between thermal stress range Δsigma in the structure and temperature change ΔT and rate of change T of the fluid in the extreme cases of an ideal thermal shock and quasi-steady-state conditions, respectively. For the real transients in between the relationship Δsigma proportional (ΔT)sup(x) Tsup(1-x)αsup(y) is proposed, where x is the shock-degree and lies between 0 and 1, and, additionally, y designates the influence of the heat transfer coefficient α. This formula yields the interpolation rule. The rule permits interpolation of stress ranges for additional thermal transients from at least 3 reference stresses via x and y. The procedure is applicable to any metallic structure, reduces fatigue analysis effort considerably and yields excellent results. The paper is split up into 2 parts. In the following the derivation of the rule is presented. The second part describes its application and will be published shortly. (orig.)

Analysis of Lithospheric Stresses Using Satellite Gravimetry: Hypotheses and Applications to North Atlantic

Science.gov (United States)

Minakov, A.; Medvedev, S.

2017-12-01

Analysis of lithospheric stresses is necessary to gain understanding of the forces that drive plate tectonics and intraplate deformations and the structure and strength of the lithosphere. A major source of lithospheric stresses is believed to be in variations of surface topography and lithospheric density. The traditional approach to stress estimation is based on direct calculations of the Gravitational Potential Energy (GPE), the depth integrated density moment of the lithosphere column. GPE is highly sensitive to density structure which, however, is often poorly constrained. Density structure of the lithosphere may be refined using methods of gravity modeling. However, the resulted density models suffer from non-uniqueness of the inverse problem. An alternative approach is to directly estimate lithospheric stresses (depth integrated) from satellite gravimetry data. Satellite gravity gradient measurements by the ESA GOCE mission ensures a wealth of data for mapping lithospheric stresses if a link between data and stresses or GPE can be established theoretically. The non-uniqueness of interpretation of sources of the gravity signal holds in this case as well. Therefore, the data analysis was tested for the North Atlantic region where reliable additional constraints are supplied by both controlled-source and earthquake seismology. The study involves comparison of three methods of stress modeling: (1) the traditional modeling approach using a thin sheet approximation; (2) the filtered geoid approach; and (3) the direct utilization of the gravity gradient tensor. Whereas the first two approaches (1)-(2) calculate GPE and utilize a computationally expensive finite element mechanical modeling to calculate stresses, the approach (3) uses a much simpler numerical treatment but requires simplifying assumptions that yet to be tested. The modeled orientation of principal stresses and stress magnitudes by each of the three methods are compared with the World Stress Map.

Profiled Roller Stress/Fatigue Life Analysis Methodology and Establishment of an Appropriate Stress/Life Exponent

Science.gov (United States)

1997-01-01

The objective of this work was to determine the three dimensional volumetric stress field, surface pressure distribution and actual contact area between a 0.50" square roller with different crown profiles and a flat raceway surface using Finite Element Analysis. The 3-dimensional stress field data was used in conjunction with several bearing fatigue life theories to extract appropriate values for stress-life exponents. Also, results of the FEA runs were used to evaluate the laminated roller model presently used for stress and life prediction.

Stress relaxation analysis and irradiation creep and swelling in pressure tubes

International Nuclear Information System (INIS)

Beeston, J.M.; Burr, T.K.

1979-01-01

An analysis is presented of slit width test information on two pressure tubes that had been irradiated in test reactors. The analysis showed that differential swelling stresses and thermal stresses undergo relaxation. The mechanism responsible for the stress relaxation at temperatures less than 700 K was irradiation creep. Irradiation creep in thermal test reactor pressure tubes is evidently greater than it would be at equivalent conditions in fast reactors. The residual stresses observed in the slit width tests varied between 30 and 257 MPa and would act to reduce the operating stresses, thus allowing for increased service life of the tubes as compared with no stress relaxation

Raman Microscopic Analysis of Internal Stress in Boron-Doped Diamond

Directory of Open Access Journals (Sweden)

Kevin E. Bennet

2015-05-01

Full Text Available Analysis of the induced stress on undoped and boron-doped diamond (BDD thin films by confocal Raman microscopy is performed in this study to investigate its correlation with sample chemical composition and the substrate used during fabrication. Knowledge of this nature is very important to the issue of long-term stability of BDD coated neurosurgical electrodes that will be used in fast-scan cyclic voltammetry, as potential occurrence of film delaminations and dislocations during their surgical implantation can have unwanted consequences for the reliability of BDD-based biosensing electrodes. To achieve a more uniform deposition of the films on cylindrically-shaped tungsten rods, substrate rotation was employed in a custom-built chemical vapor deposition reactor. In addition to visibly preferential boron incorporation into the diamond lattice and columnar growth, the results also reveal a direct correlation between regions of pure diamond and enhanced stress. Definite stress release throughout entire film thicknesses was found in the current Raman mapping images for higher amounts of boron addition. There is also a possible contribution to the high values of compressive stress from sp2 type carbon impurities, besides that of the expected lattice mismatch between film and substrate.

Genome-wide analysis identifies chickpea (Cicer arietinum) heat stress transcription factors (Hsfs) responsive to heat stress at the pod development stage.

Science.gov (United States)

Chidambaranathan, Parameswaran; Jagannadham, Prasanth Tej Kumar; Satheesh, Viswanathan; Kohli, Deshika; Basavarajappa, Santosh Halasabala; Chellapilla, Bharadwaj; Kumar, Jitendra; Jain, Pradeep Kumar; Srinivasan, R

2018-05-01

The heat stress transcription factors (Hsfs) play a prominent role in thermotolerance and eliciting the heat stress response in plants. Identification and expression analysis of Hsfs gene family members in chickpea would provide valuable information on heat stress responsive Hsfs. A genome-wide analysis of Hsfs gene family resulted in the identification of 22 Hsf genes in chickpea in both desi and kabuli genome. Phylogenetic analysis distinctly separated 12 A, 9 B, and 1 C class Hsfs, respectively. An analysis of cis-regulatory elements in the upstream region of the genes identified many stress responsive elements such as heat stress elements (HSE), abscisic acid responsive element (ABRE) etc. In silico expression analysis showed nine and three Hsfs were also expressed in drought and salinity stresses, respectively. Q-PCR expression analysis of Hsfs under heat stress at pod development and at 15 days old seedling stage showed that CarHsfA2, A6, and B2 were significantly upregulated in both the stages of crop growth and other four Hsfs (CarHsfA2, A6a, A6c, B2a) showed early transcriptional upregulation for heat stress at seedling stage of chickpea. These subclasses of Hsfs identified in this study can be further evaluated as candidate genes in the characterization of heat stress response in chickpea.

Photoplethysmography Based Mental Stress Analysis Algorithm and System for Human Wellbeing Life

Directory of Open Access Journals (Sweden)

Jong-Ha Lee

2017-01-01

Full Text Available HRV, physiological indicators, using the PPG data was found to be changed by mental stress. Our results indicate that PPG measurement may be one of the easiest ways to assess the mental stress quantitatively. In a subsequent experiment, it is necessary to find out the relationship between the physiological indicators and various types of psychological stress.

Electromagnetic field and mechanical stress analysis code

International Nuclear Information System (INIS)

1978-01-01

Analysis TEXMAGST is a two stage linear finite element code for the analysis of static magnetic fields in three dimensional structures and associated mechanical stresses produced by the anti J x anti B forces within these structures. The electromagnetic problem is solved in terms of magnetic vector potential A for a given current density anti J as curl 1/μ curl anti A = anti J considering the magnetic permeability as constant. The Coulombian gauge (div anti A = o) was chosen and was implemented through the use of Lagrange multipliers. The second stage of the problem - the calculation of mechanical stresses in the same three dimensional structure is solved by using the same code with few modifications - through a restart card. Body forces anti J x anti B within each element are calculated from the solution of the first stage run and represent the input to the second stage run which will give the solution for the stress problem

A fractal model of effective stress of porous media and the analysis of influence factors

Science.gov (United States)

Li, Wei; Zhao, Huan; Li, Siqi; Sun, Wenfeng; Wang, Lei; Li, Bing

2018-03-01

The basic concept of effective stress describes the characteristics of fluid and solid interaction in porous media. In this paper, based on the theory of fractal geometry, a fractal model was built to analyze the relationship between the microstructure and the effective stress of porous media. From the microscopic point of view, the influence of effective stress on pore structure of porous media was demonstrated. Theoretical analysis and experimental results show that: (i) the fractal model of effective stress can be used to describe the relationship between effective stress and the microstructure of porous media; (ii) a linear increase in the effective stress leads to exponential increases in fractal dimension, porosity and pore number of the porous media, and causes a decreasing trend in the average pore radius.

PIPE STRESS and VERPIP codes for stress analysis and verifications of PEC reactor piping

International Nuclear Information System (INIS)

Cesari, F.; Ferranti, P.; Gasparrini, M.; Labanti, L.

1975-01-01

To design LMFBR piping systems following ASME Sct. III requirements unusual flexibility computer codes are to be adopted to consider piping and its guard-tube. For this purpose PIPE STRESS code previously prepared by Southern-Service, has been modified. Some subroutine for detailed stress analysis and principal stress calculations on all the sections of piping have been written and fitted in the code. Plotter can also be used. VERPIP code for automatic verifications of piping as class 1 Sct. III prescriptions has been also prepared. The results of PIPE STRESS and VERPIP codes application to PEC piping are in section III of this report

Baking system for ports of experimental advanced super-conducting tokamak vacuum vessel and thermal stress analysis

International Nuclear Information System (INIS)

Cheng Yali; Bao Liman; Song Yuntao; Yao Damao

2006-01-01

The baking system of Experimental Advanced Super-Conducting Toakamk (EAST) vacuum vessel is necessary to obtain the baking temperature of 150 degree C. In order to define suitable alloy heaters and achieve their reasonable layouts, thermal analysis was carried out with ANSYS code. The analysis results indicate that the temperature distribution and thermal stress of most parts of EAST vacuum vessel ports are uniform, satisfied for the requirement, and are safe based on ASME criterion. Feasible idea on reducing the stress focus is also considered. (authors)

Advanced stress analysis of PWR containments in the region of nozzles

International Nuclear Information System (INIS)

Schauer, G.

1977-01-01

As an example of the stress analysis of a nozzle in a PWR steel containment, an advanced stress analysis of a personnel lock is presented. Contrary to the calculations by means of numerical shell programs usual till now, this advanced stress analysis was executed with the finite-element-method. Because of their theory, the shell programs compute mathematically exact results, but at the intersection of two shells the notch stresses cannot be analyzed well. A further disadvantage must be seen in the fact that there is a great distance between the real critical region near the intersection line and the calculation point, which lies on the neutral axis of the shell

Application of the whole powder pattern decomposition procedure in the residual stress analysis of layers and coatings

International Nuclear Information System (INIS)

Schoderböck, Peter; Brechbühl, Jens

2015-01-01

The X-ray investigation of stress states in materials, based on the determination of elastic lattice strains which are converted to stresses by means of theory of elasticity, is a necessity in quality control of thin layers and coatings for optimizing manufacturing steps and process parameters. This work introduces the evaluation of residual stress from complex and overlapping diffraction patterns using a whole-powder pattern decomposition procedure defining a 2θ-offset caused by residual stresses. Furthermore corrections for sample displacement and refraction are directly implemented in the calculation procedure. The correlation matrices of the least square fitting routines have been analyzed for parameter interactions and obvious interdependencies have been decoupled by the introduction of an internal standard within the diffraction experiment. This decomposition based evaluation has been developed on tungsten as a model material system and its efficiency was demonstrated by X-ray diffraction analysis of a solid oxide fuel cell multilayer system. The results are compared with those obtained by the classical sin 2 Ψ-method. - Highlights: • Analysis of complex multiphase diffraction patterns with respect to residual stress • Stress-gradient determination with in situ correction of displacement and refraction • Consideration of the elastic anisotropy within the refinement

Development of total systems of piping stress analysis and evaluation: ISAPPS

International Nuclear Information System (INIS)

Oki, Teizaburo; Koyanagi, Ryoichi; Fukuda, Masanao

1978-01-01

IHI has developed the systems of piping stress analysis and evaluation: ISAPPS (IHI Stress Analysis Program for Piping Systems), which are further described in this paper. In addition, the results of structural analysis and heat transfer analysis were confirmed. An example of stress evaluation in accordance with the modified ASME Code Sec. III is shown. ISAPPS consists of the following seven parts, and is designed for easy adoption of other programs by making modifications. 1. Piping design oriented language programs 2. Structural analysis programs 3. Isometric plotting programs 4. Multi-file dumping program 5. Load combination program 6. Heat transfer program 7. Stress evaluation programs As one of the examples of structural analysis programs, IHI make use of the modified SAP IV developed by the University of California. Evaluations of stresses are performed in accordance with: 1. ASME Boiler and Pressure Vessel Code, Sec. III Class 1, 2 and 3 2. ANSI Code, B31.1 and B31.3 3. MITI (Ministry of International Trade and Industry ) Code ISAPPS is very useful for design of nuclear and chemical pipings and so on. (author)

Complete stress tensor determination by microearthquake analysis

Science.gov (United States)

Slunga, R.

2010-12-01

the depth based on the assumptions of a fractured crust, widely vary ing stress field, and a general closeness to instability as found by stress measurements (Jamison and Cook 1976). Wheather this approach is working or not is best answered by applying it to real data. This was provided by the IMO network in Iceland. Along Southern Iceland Seismic Zone (SISZ) more than 200,000 microearthquakes and a few M 5 EQs and 2 M=6.6 EQs have been recorded. The results will be presented it is obvious that the use of the stresses determined from the microearthquake recordings may significa ntly improve earthquake warnings and will make it possible to use the absolute C FS method for more deterministic predictions. Note that the microearthquake meth od only shows the part of the stress field that has caused slip. Volumes with st able stress will not show up. However stress measurements (Brown and Hoek 1978, Slunga 1988) have shown that the crustal stresses in general are close to instabi lity and microearthquake source analysis has shown that a large number of differ ent fractures become unstable within longer time windows. This may explain the e xcellent results given by the Icelandic tests of the absolute stress tensor fiel d as given by the microearthquakes. However I prefer to call this stress apparen t.

Reliability prediction of large fuel cell stack based on structure stress analysis

Science.gov (United States)

Liu, L. F.; Liu, B.; Wu, C. W.

2017-09-01

The aim of this paper is to improve the reliability of Proton Electrolyte Membrane Fuel Cell (PEMFC) stack by designing the clamping force and the thickness difference between the membrane electrode assembly (MEA) and the gasket. The stack reliability is directly determined by the component reliability, which is affected by the material property and contact stress. The component contact stress is a random variable because it is usually affected by many uncertain factors in the production and clamping process. We have investigated the influences of parameter variation coefficient on the probability distribution of contact stress using the equivalent stiffness model and the first-order second moment method. The optimal contact stress to make the component stay in the highest level reliability is obtained by the stress-strength interference model. To obtain the optimal contact stress between the contact components, the optimal thickness of the component and the stack clamping force are optimally designed. Finally, a detailed description is given how to design the MEA and gasket dimensions to obtain the highest stack reliability. This work can provide a valuable guidance in the design of stack structure for a high reliability of fuel cell stack.

Population Structure, Genetic Diversity and Molecular Marker-Trait Association Analysis for High Temperature Stress Tolerance in Rice.

Directory of Open Access Journals (Sweden)

Sharat Kumar Pradhan

Full Text Available Rice exhibits enormous genetic diversity, population structure and molecular marker-traits associated with abiotic stress tolerance to high temperature stress. A set of breeding lines and landraces representing 240 germplasm lines were studied. Based on spikelet fertility percent under high temperature, tolerant genotypes were broadly classified into four classes. Genetic diversity indicated a moderate level of genetic base of the population for the trait studied. Wright's F statistic estimates showed a deviation of Hardy-Weinberg expectation in the population. The analysis of molecular variance revealed 25 percent variation between population, 61 percent among individuals and 14 percent within individuals in the set. The STRUCTURE analysis categorized the entire population into three sub-populations and suggested that most of the landraces in each sub-population had a common primary ancestor with few admix individuals. The composition of materials in the panel showed the presence of many QTLs representing the entire genome for the expression of tolerance. The strongly associated marker RM547 tagged with spikelet fertility under stress and the markers like RM228, RM205, RM247, RM242, INDEL3 and RM314 indirectly controlling the high temperature stress tolerance were detected through both mixed linear model and general linear model TASSEL analysis. These markers can be deployed as a resource for marker-assisted breeding program of high temperature stress tolerance.

Population Structure, Genetic Diversity and Molecular Marker-Trait Association Analysis for High Temperature Stress Tolerance in Rice.

Science.gov (United States)

Pradhan, Sharat Kumar; Barik, Saumya Ranjan; Sahoo, Ambika; Mohapatra, Sudipti; Nayak, Deepak Kumar; Mahender, Anumalla; Meher, Jitandriya; Anandan, Annamalai; Pandit, Elssa

2016-01-01

Rice exhibits enormous genetic diversity, population structure and molecular marker-traits associated with abiotic stress tolerance to high temperature stress. A set of breeding lines and landraces representing 240 germplasm lines were studied. Based on spikelet fertility percent under high temperature, tolerant genotypes were broadly classified into four classes. Genetic diversity indicated a moderate level of genetic base of the population for the trait studied. Wright's F statistic estimates showed a deviation of Hardy-Weinberg expectation in the population. The analysis of molecular variance revealed 25 percent variation between population, 61 percent among individuals and 14 percent within individuals in the set. The STRUCTURE analysis categorized the entire population into three sub-populations and suggested that most of the landraces in each sub-population had a common primary ancestor with few admix individuals. The composition of materials in the panel showed the presence of many QTLs representing the entire genome for the expression of tolerance. The strongly associated marker RM547 tagged with spikelet fertility under stress and the markers like RM228, RM205, RM247, RM242, INDEL3 and RM314 indirectly controlling the high temperature stress tolerance were detected through both mixed linear model and general linear model TASSEL analysis. These markers can be deployed as a resource for marker-assisted breeding program of high temperature stress tolerance.

Cereal Crop Proteomics: Systemic Analysis of Crop Drought Stress Responses Towards Marker-Assisted Selection Breeding

Directory of Open Access Journals (Sweden)

Arindam Ghatak

2017-06-01

Full Text Available Sustainable crop production is the major challenge in the current global climate change scenario. Drought stress is one of the most critical abiotic factors which negatively impact crop productivity. In recent years, knowledge about molecular regulation has been generated to understand drought stress responses. For example, information obtained by transcriptome analysis has enhanced our knowledge and facilitated the identification of candidate genes which can be utilized for plant breeding. On the other hand, it becomes more and more evident that the translational and post-translational machinery plays a major role in stress adaptation, especially for immediate molecular processes during stress adaptation. Therefore, it is essential to measure protein levels and post-translational protein modifications to reveal information about stress inducible signal perception and transduction, translational activity and induced protein levels. This information cannot be revealed by genomic or transcriptomic analysis. Eventually, these processes will provide more direct insight into stress perception then genetic markers and might build a complementary basis for future marker-assisted selection of drought resistance. In this review, we survey the role of proteomic studies to illustrate their applications in crop stress adaptation analysis with respect to productivity. Cereal crops such as wheat, rice, maize, barley, sorghum and pearl millet are discussed in detail. We provide a comprehensive and comparative overview of all detected protein changes involved in drought stress in these crops and have summarized existing knowledge into a proposed scheme of drought response. Based on a recent proteome study of pearl millet under drought stress we compare our findings with wheat proteomes and another recent study which defined genetic marker in pearl millet.

Computer-aided stress analysis system for nuclear plant primary components

International Nuclear Information System (INIS)

Murai, Tsutomu; Tokumaru, Yoshio; Yamazaki, Junko.

1980-06-01

Generally it needs a vast quantity of calculation to make the stress analysis reports of nuclear plant primary components. In Japan, especially, stress analysis reports are under obligation to make for each plant. In Mitsubishi Heavy Industries, Ltd., We have been making great efforts to rationalize the process of analysis for about these ten years. As the result of rationalization up to now, a computer-aided stress analysis system using graphic display, graphic tablet, data file, etc. was accomplished and it needs us only the least hand work. In addition we developed a fracture safety analysis system. And we are going to develop the input generator system for 3-dimensional FEM analysis by graphics terminals in the near future. We expect that when the above-mentioned input generator system is accomplished, it will be possible for us to solve instantly any case of problem. (author)

Image decomposition as a tool for validating stress analysis models

Directory of Open Access Journals (Sweden)

Mottershead J.

2010-06-01

Full Text Available It is good practice to validate analytical and numerical models used in stress analysis for engineering design by comparison with measurements obtained from real components either in-service or in the laboratory. In reality, this critical step is often neglected or reduced to placing a single strain gage at the predicted hot-spot of stress. Modern techniques of optical analysis allow full-field maps of displacement, strain and, or stress to be obtained from real components with relative ease and at modest cost. However, validations continued to be performed only at predicted and, or observed hot-spots and most of the wealth of data is ignored. It is proposed that image decomposition methods, commonly employed in techniques such as fingerprinting and iris recognition, can be employed to validate stress analysis models by comparing all of the key features in the data from the experiment and the model. Image decomposition techniques such as Zernike moments and Fourier transforms have been used to decompose full-field distributions for strain generated from optical techniques such as digital image correlation and thermoelastic stress analysis as well as from analytical and numerical models by treating the strain distributions as images. The result of the decomposition is 101 to 102 image descriptors instead of the 105 or 106 pixels in the original data. As a consequence, it is relatively easy to make a statistical comparison of the image descriptors from the experiment and from the analytical/numerical model and to provide a quantitative assessment of the stress analysis.

Effects of Mindfulness-Based Stress Reduction on employees’ mental health: A systematic review

Science.gov (United States)

Heerkens, Yvonne; Kuijer, Wietske; van der Heijden, Beatrice; Engels, Josephine

2018-01-01

Objectives The purpose of this exploratory study was to obtain greater insight into the effects of Mindfulness-Based Stress Reduction (MBSR) and Mindfulness-Based Cognitive Therapy (MBCT) on the mental health of employees. Methods Using PsycINFO, PubMed, and CINAHL, we performed a systematic review in October 2015 of studies investigating the effects of MBSR and MBCT on various aspects of employees’ mental health. Studies with a pre-post design (i.e. without a control group) were excluded. Results 24 articles were identified, describing 23 studies: 22 on the effects of MBSR and 1 on the effects of MBSR in combination with some aspects of MBCT. Since no study focused exclusively on MBCT, its effects are not described in this systematic review. Of the 23 studies, 2 were of high methodological quality, 15 were of medium quality and 6 were of low quality. A meta-analysis was not performed due to the emergent and relatively uncharted nature of the topic of investigation, the exploratory character of this study, and the diversity of outcomes in the studies reviewed. Based on our analysis, the strongest outcomes were reduced levels of emotional exhaustion (a dimension of burnout), stress, psychological distress, depression, anxiety, and occupational stress. Improvements were found in terms of mindfulness, personal accomplishment (a dimension of burnout), (occupational) self-compassion, quality of sleep, and relaxation. Conclusion The results of this systematic review suggest that MBSR may help to improve psychological functioning in employees. PMID:29364935

Paint coating characterization for thermoelastic stress analysis of metallic materials

International Nuclear Information System (INIS)

Robinson, A F; Dulieu-Barton, J M; Quinn, S; Burguete, R L

2010-01-01

In thermoelastic stress analysis (TSA) it is normal practice to coat metallic specimens with black paint to enhance and standardize the surface emissivity. It is assumed that the paint coating has no effect on the thermal emission from the specimen, but it is well known that the response is sensitive to paint coating thickness, particularly at higher frequencies. In this paper the effects of loading frequency and paint coating thickness on the thermoelastic response are investigated. The thermoelastic response is compared to theory, and optimum test conditions and coating characteristics are suggested. The motivation for the work is to develop a TSA-based means of residual stress assessment, where the measurement of much smaller temperature changes than those that are resolved in standard TSA is required; therefore the analysis is much more sensitive to the effects of the paint coating. However, the work presented in this paper is relevant to a wide range of TSA investigations and presents data that will be of interest to all practitioners of TSA

Implications of stress range for inelastic analysis

International Nuclear Information System (INIS)

Karabin, M.E.; Dhalla, A.K.

1981-01-01

The elastic stress range over a complete load cycle is routinely used to formulate simplified rules regarding the inelastic behavior of structures operating at elevated temperature. For example, a 300 series stainless steel structure operating at elevated temperature, in all probability, would satisfy the ASME Boiler and Pressure Vessel Code criteria if the linearized elastic stress range is less than three times the material yield strength. However, at higher elastic stress ranges it is difficult to judge, a priori, that a structural component would comply with inelastic Code criteria after a detailed inelastic analysis. The purpose of this paper is to illustrate that it is not the elastic stress range but the stress intensities at specific times during a thermal transient which provide a better insight into the inelastic response of the structure. The specific example of the CRBRP flued head design demonstrates that the temperature differential between various parts of the structure can be changed by modifying the insulation pattern and heat flow path in the structure, without significantly altering the elastic stress range over a complete load cycle. However, the modified design did reduce the stress intensity during steady state elevated temperature operation. This modified design satisfied the inelastic Code criteria whereas the initial design failed to comply with the strain accumulation criterion

Enriching Genomic Resources and Transcriptional Profile Analysis of Miscanthus sinensis under Drought Stress Based on RNA Sequencing

Directory of Open Access Journals (Sweden)

Gang Nie

2017-01-01

Full Text Available Miscanthus × giganteus is wildly cultivated as a potential biofuel feedstock around the world; however, the narrow genetic basis and sterile characteristics have become a limitation for its utilization. As a progenitor of M. × giganteus, M. sinensis is widely distributed around East Asia providing well abiotic stress tolerance. To enrich the M. sinensis genomic databases and resources, we sequenced and annotated the transcriptome of M. sinensis by using an Illumina HiSeq 2000 platform. Approximately 316 million high-quality trimmed reads were generated from 349 million raw reads, and a total of 114,747 unigenes were obtained after de novo assembly. Furthermore, 95,897 (83.57% unigenes were annotated to at least one database including NR, Swiss-Prot, KEGG, COG, GO, and NT, supporting that the sequences obtained were annotated properly. Differentially expressed gene analysis indicates that drought stress 15 days could be a critical period for M. sinensis response to drought stress. The high-throughput transcriptome sequencing of M. sinensis under drought stress has greatly enriched the current genomic available resources. The comparison of DEGs under different periods of drought stress identified a wealth of candidate genes involved in drought tolerance regulatory networks, which will facilitate further genetic improvement and molecular studies of the M. sinensis.

Stress and Displacement Analysis of Microreactors during Thermal and Vacuum Loading

Science.gov (United States)

2017-09-07

ARL-TR-8121 ● SEP 2017 US Army Research Laboratory Stress and Displacement Analysis of Microreactors during Thermal and Vacuum...is no longer needed. Do not return it to the originator. ARL-TR-8121 ● SEP 2017 US Army Research Laboratory Stress and...TITLE AND SUBTITLE Stress and Displacement Analysis of Microreactors during Thermal and Vacuum Loading 5a. CONTRACT NUMBER 5b. GRANT NUMBER

Monitoring expression profiles of rice (Oryza sativa L.) genes under abiotic stresses using cDNA Microarray Analysis (abstract)

International Nuclear Information System (INIS)

Rabbani, M.A.

2005-01-01

Transcript regulation in response to cold, drought, high salinity and ABA application was investigated in rice (Oryza sativa L., Nipponbare) with microarray analysis including approx. 1700 independent DNA elements derived from three cDNA libraries constructed from 15-day old rice seedlings stressed with drought, cold and high salinity. A total of 141 non-redundant genes were identified, whose expression ratios were more than three-fold compared with the control genes for at least one of stress treatments in microarray analysis. However, after RNA gel blot analysis, a total of 73 genes were identified, among them the transcripts of 36, 62, 57 and 43 genes were found increased after cold, drought, high salinity and ABA application, respectively. Sixteen of these identified genes have been reported previously to be stress inducible in rice, while 57 of which are novel that have not been reported earlier as stress responsive in rice. We observed a strong association in the expression patterns of stress responsive genes and found 15 stress inducible genes that responded to all four treatments. Based on Venn diagram analysis, 56 genes were induced by both drought and high salinity, whereas 22 genes were upregulated by both cold and high salinity stress. Similarly 43 genes were induced by both drought stress and ABA application, while only 17 genes were identified as cold and ABA inducible genes. These results indicated the existence of greater cross talk between drought, ABA and high salinity stress signaling processes than those between cold and ABA, and cold and high salinity stress signaling pathways. The cold, drought, high salinity and ABA inducible genes were classified into four gene groups from their expression profiles. Analysis of data enabled us to identify a number of promoters and possible cis-acting DNA elements of several genes induced by a variety of abiotic stresses by combining expression data with genomic sequence data of rice. Comparative analysis of

Failure assessments of corroded pipelines with axial defects using stress-based criteria: Numerical studies and verification analyses

International Nuclear Information System (INIS)

Chiodo, Mario S.G.; Ruggieri, Claudio

2009-01-01

Conventional procedures used to assess the integrity of corroded piping systems with axial defects generally employ simplified failure criteria based upon a plastic collapse failure mechanism incorporating the tensile properties of the pipe material. These methods establish acceptance criteria for defects based on limited experimental data for low strength structural steels which do not necessarily address specific requirements for the high grade steels currently used. For these cases, failure assessments may be overly conservative or provide significant scatter in their predictions, which lead to unnecessary repair or replacement of in-service pipelines. Motivated by these observations, this study examines the applicability of a stress-based criterion based upon plastic instability analysis to predict the failure pressure of corroded pipelines with axial defects. A central focus is to gain additional insight into effects of defect geometry and material properties on the attainment of a local limit load to support the development of stress-based burst strength criteria. The work provides an extensive body of results which lend further support to adopt failure criteria for corroded pipelines based upon ligament instability analyses. A verification study conducted on burst testing of large-diameter pipe specimens with different defect length shows the effectiveness of a stress-based criterion using local ligament instability in burst pressure predictions, even though the adopted burst criterion exhibits a potential dependence on defect geometry and possibly on material's strain hardening capacity. Overall, the results presented here suggests that use of stress-based criteria based upon plastic instability analysis of the defect ligament is a valid engineering tool for integrity assessments of pipelines with axial corroded defects

Failure assessments of corroded pipelines with axial defects using stress-based criteria: Numerical studies and verification analyses

Energy Technology Data Exchange (ETDEWEB)

Chiodo, Mario S.G. [Department of Naval Architecture and Ocean Engineering, University of Sao Paulo, Av. Prof. Mello Moraes, 2231 (PNV-EPUSP), Sao Paulo, SP 05508-030 (Brazil); Ruggieri, Claudio [Department of Naval Architecture and Ocean Engineering, University of Sao Paulo, Av. Prof. Mello Moraes, 2231 (PNV-EPUSP), Sao Paulo, SP 05508-030 (Brazil)], E-mail: claudio.ruggieri@poli.usp.br

2009-02-15

Conventional procedures used to assess the integrity of corroded piping systems with axial defects generally employ simplified failure criteria based upon a plastic collapse failure mechanism incorporating the tensile properties of the pipe material. These methods establish acceptance criteria for defects based on limited experimental data for low strength structural steels which do not necessarily address specific requirements for the high grade steels currently used. For these cases, failure assessments may be overly conservative or provide significant scatter in their predictions, which lead to unnecessary repair or replacement of in-service pipelines. Motivated by these observations, this study examines the applicability of a stress-based criterion based upon plastic instability analysis to predict the failure pressure of corroded pipelines with axial defects. A central focus is to gain additional insight into effects of defect geometry and material properties on the attainment of a local limit load to support the development of stress-based burst strength criteria. The work provides an extensive body of results which lend further support to adopt failure criteria for corroded pipelines based upon ligament instability analyses. A verification study conducted on burst testing of large-diameter pipe specimens with different defect length shows the effectiveness of a stress-based criterion using local ligament instability in burst pressure predictions, even though the adopted burst criterion exhibits a potential dependence on defect geometry and possibly on material's strain hardening capacity. Overall, the results presented here suggests that use of stress-based criteria based upon plastic instability analysis of the defect ligament is a valid engineering tool for integrity assessments of pipelines with axial corroded defects.

Buckling analysis of orthotropic protein microtubules under axial and radial compression based on couple stress theory.

Science.gov (United States)

Beni, Yaghoub Tadi; Zeverdejani, M Karimi; Mehralian, Fahimeh

2017-10-01

Protein microtubules (MTs) are one of the important intercellular components and have a vital role in the stability and strength of the cells. Due to applied external loads, protein microtubules may be involved buckling phenomenon. Due to impact of protein microtubules in cell reactions, it is important to determine their critical buckling load. Considering nature of protein microtubules, various parameters are effective on microtubules buckling. The small size of microtubules and also lack of uniformity of MTs properties in different directions caused the necessity of accuracy in the analysis of these bio-structure. In fact, microtubules must be considered as a size dependent cylinder, which behave as an orthotropic material. Hence, in the present work using first-order shear deformation model (FSDT), the buckling equations of anisotropic MTs are derived based on new modified couple stress theory (NMCST). After solving the stability equations, the influences of various parameters are measured on the MTs critical buckling load. Copyright © 2017 Elsevier Inc. All rights reserved.

Analysis of stress-strain relationships in silicon ribbon

Science.gov (United States)

Dillon, O. W., Jr.

1984-01-01

An analysis of stress-strain relationships in silicon ribbon is presented. A model to present entire process, dynamical Transit Analysis is developed. It is found that knowledge of past-strain history is significant in modeling activities.

Genome-Wide Identification, Evolutionary Analysis, and Stress Responses of the GRAS Gene Family in Castor Beans

Directory of Open Access Journals (Sweden)

Wei Xu

2016-06-01

Full Text Available Plant-specific GRAS transcription factors play important roles in regulating growth, development, and stress responses. Castor beans (Ricinus communis are important non-edible oilseed plants, cultivated worldwide for its seed oils and its adaptability to growth conditions. In this study, we identified and characterized a total of 48 GRAS genes based on the castor bean genome. Combined with phylogenetic analysis, the castor bean GRAS members were divided into 13 distinct groups. Functional divergence analysis revealed the presence of mostly Type-I functional divergence. The gene structures and conserved motifs, both within and outside the GRAS domain, were characterized. Gene expression analysis, performed in various tissues and under a range of abiotic stress conditions, uncovered the potential functions of GRAS members in regulating plant growth development and stress responses. The results obtained from this study provide valuable information toward understanding the potential molecular mechanisms of GRAS proteins in castor beans. These findings also serve as a resource for identifying the genes that allow castor beans to grow in stressful conditions and to enable further breeding and genetic improvements in agriculture.

In Silico Analysis of Mobilome Response to Salt Stress in Phaseolus vulgaris L.

Directory of Open Access Journals (Sweden)

Behcet İNAL

2018-02-01

Full Text Available Common bean is an important legume that grown and consumed as animal feed and for human nutrition. It is also an important source of protein in developing countries. Transposable elements (TEs constitute a large part of the genome in various eukaryotic species. TE was described as garbage DNA by researchers for a long time. Recently, it has been found that TEs can move near stress response genes and they have known effects on plant resistance to diverse stresses. With the acquisition of common bean genome sequence, one of the next step is to annotate the genome and define the functional DNA elements. TEs are the most abundant genetic elements of plant genomes and have an important impact on genome stress evolution and genetic variation. So, it is important to determine TEs in the common bean genome. In the current study, genome-wide transposon annotation and definition were achieved in root and leaf tissues of common bean under salt stress. Homology and sequence structure-based methods were used. Tont2-I-Copia and Copia-39 Copia retrotransposons were found to be more in salt-treated roots and leaves respectively. As a result of the analysis, we found TEs number ranging from 46 to 50 belonging to about twenty different plants. Gene ontology analysis of transposon sequences brought the light on diverse important pathways related to abiotic stress conditions.

Non-linear analysis and the design of Pumpkin Balloons: stress, stability and viscoelasticity

Science.gov (United States)

Rand, J. L.; Wakefield, D. S.

Tensys have a long-established background in the shape generation and load analysis of architectural stressed membrane structures Founded upon their inTENS finite element analysis suite these activities have broadened to encompass lighter than air structures such as aerostats hybrid air-vehicles and stratospheric balloons Winzen Engineering couple many years of practical balloon design and fabrication experience with both academic and practical knowledge of the characterisation of the non-linear viscoelastic response of the polymeric films typically used for high-altitude scientific balloons Both companies have provided consulting services to the NASA Ultra Long Duration Balloon ULDB Program Early implementations of pumpkin balloons have shown problems of geometric instability characterised by improper deployment and these difficulties have been reproduced numerically using inTENS The solution lies in both the shapes of the membrane lobes and also the need to generate a biaxial stress field in order to mobilise in-plane shear stiffness Balloons undergo significant temperature and pressure variations in flight The different thermal characteristics between tendons and film can lead to significant meridional stress Fabrication tolerances can lead to significant local hoop stress concentrations particularly adjacent to the base and apex end fittings The non-linear viscoelastic response of the envelope film acts positively to help dissipate stress concentrations However creep over time may produce lobe geometry variations that may

Analysis of a plane stress wave by the moving least squares method

Directory of Open Access Journals (Sweden)

Wojciech Dornowski

2014-08-01

Full Text Available A meshless method based on the moving least squares approximation is applied to stress wave propagation analysis. Two kinds of node meshes, the randomly generated mesh and the regular mesh are used. The nearest neighbours’ problem is developed from a triangulation that satisfies minimum edges length conditions. It is found that this method of neighbours’ choice significantly improves the solution accuracy. The reflection of stress waves from the free edge is modelled using fictitious nodes (outside the plate. The comparison with the finite difference results also demonstrated the accuracy of the proposed approach.[b]Keywords[/b]: civil engineering, meshless method, moving least squares method, elastic waves

Stress analysis of implant-bone fixation at different fracture angle

Science.gov (United States)

Izzawati, B.; Daud, R.; Afendi, M.; Majid, MS Abdul; Zain, N. A. M.; Bajuri, Y.

2017-10-01

Internal fixation is a mechanism purposed to maintain and protect the reduction of a fracture. Understanding of the fixation stability is necessary to determine parameters influence the mechanical stability and the risk of implant failure. A static structural analysis on a bone fracture fixation was developed to simulate and analyse the biomechanics of a diaphysis shaft fracture with a compression plate and conventional screws. This study aims to determine a critical area of the implant to be fractured based on different implant material and angle of fracture (i.e. 0°, 30° and 45°). Several factors were shown to influence stability to implant after surgical. The stainless steel, (S. S) and Titanium, (Ti) screws experienced the highest stress at 30° fracture angle. The fracture angle had a most significant effect on the conventional screw as compared to the compression plate. The stress was significantly higher in S.S material as compared to Ti material, with concentrated on the 4th screw for all range of fracture angle. It was also noted that the screws closest to the intense concentration stress areas on the compression plate experienced increasing amounts of stress. The highest was observed at the screw thread-head junction.

Interventions to reduce stress in university students: a review and meta-analysis.

Science.gov (United States)

Regehr, Cheryl; Glancy, Dylan; Pitts, Annabel

2013-05-15

Recent research has revealed concerning rates of anxiety and depression among university students. Nevertheless, only a small percentage of these students receive treatment from university health services. Universities are thus challenged with instituting preventative programs that address student stress and reduce resultant anxiety and depression. A systematic review of the literature and meta-analysis was conducted to examine the effectiveness of interventions aimed at reducing stress in university students. Studies were eligible for inclusion if the assignment of study participants to experimental or control groups was by random allocation or parallel cohort design. Retrieved studies represented a variety of intervention approaches with students in a broad range of programs and disciplines. Twenty-four studies, involving 1431 students were included in the meta-analysis. Cognitive, behavioral and mindfulness interventions were associated with decreased symptoms of anxiety. Secondary outcomes included lower levels of depression and cortisol. Included studies were limited to those published in peer reviewed journals. These studies over-represent interventions with female students in Western countries. Studies on some types of interventions such as psycho-educational and arts based interventions did not have sufficient data for inclusion in the meta-analysis. This review provides evidence that cognitive, behavioral, and mindfulness interventions are effective in reducing stress in university students. Universities are encouraged to make such programs widely available to students. In addition however, future work should focus on developing stress reduction programs that attract male students and address their needs. Copyright © 2012 Elsevier B.V. All rights reserved.

Oil prices and financial stress: A volatility spillover analysis

International Nuclear Information System (INIS)

Nazlioglu, Saban; Soytas, Ugur; Gupta, Rangan

2015-01-01

This paper examines whether there is a volatility transmission between oil prices and financial stress by means of the volatility spillover test. We employ WTI crude oil prices and Cleveland financial stress index for the period 1991–2014 and divide the sample into pre-crisis, in-crisis, and post-crisis periods due to the downward trend in oil price in 2008. The volatility model estimations indicate that oil prices and financial stress index are dominated by long-run volatility. The volatility spillover causality test supports evidence on risk transfer from oil prices to financial stress before the crisis and from financial stress to oil prices after the crisis. The impulse response analysis shows that the volatility transmission pattern has similar dynamics before and after the crisis and is characterized by higher and long-lived effects during the crisis. Our results have implications for both policy makers and investors, and for future work. -- Highlights: •Volatility spillover between oil prices and financial stress index is examined. •Analysis is conducted for sub-periods: pre-crisis, in-crisis, and post-crisis •Oil prices spill on financial stress before the crisis, but spillover reversed after the crisis. •Volatility transmission pattern has similar dynamics before and after the crisis. •Implications for investors and policy makers are discussed

Stress analysis of the HFIR HB-2 and HB-3 beam tube nozzles

International Nuclear Information System (INIS)

Williams, P.T.

1998-08-01

The results of three-dimensional linear elastic stress analyses of the HFIR HB-2 and HB-3 nozzles are presented in this report. Finite element models were developed using the PATRAN pre-processing code and translated into ABAQUS input file format. A scoping analysis using simple geometries with internal pressure loading was carried out to assess the capabilities of the ABAQUS/Standard code to calculate maximum principal stress distributions within cylinders with and without holes. These scoping calculations were also used to provide estimates for the variation in tangential stress around the rim of a nozzle using the superposition of published closed-form solutions for the stress around a hole in an infinite flat plate under uniaxial tension. From the results of the detailed finite element models, peak stress concentration factors (based on the maximum principal stresses in tension) were calculated to be 3.0 for the HB-2 nozzle and 2.8 for the HB-3 nozzle. Submodels for each nozzle were built to calculate the maximum principal stress distribution in the weldment region around the nozzle, where displacement boundary conditions for the submodels were automatically calculated by ABAQUS using the results of the global nozzle models. Maximum principal stresses are plotted and tabulated for eight positions around each nozzle and nozzle weldment

X-ray multiaxial stress analysis by means of polynomial approximation and an application to plane stress problem

International Nuclear Information System (INIS)

Yoshioka, Yasuo; Sasaki, Toshihiko; Kuramoto, Makoto.

1984-01-01

A new polynomial approximation method was proposed for the X-ray multiaxial stress analysis, in which the effect of stress gradient along the penetration depth of X-rays was taken into account. Three basic assumptions were made; (1) the stress gradient is linear in respect to the depth from the specimen surface, (2) the ponetration depth of X-rays is a function of Sin 2 phi and (3) the strain measured by X-rays corresponds to the weighted average strain on the intensity of the diffracted X-rays. Consequently, the stress state within the thin layer near the surface was expressed by making use of three surface stresses and six stress gradients in the present method. The average strains by X-rays were approximated by the third order polynomial equations of sin 2 phi using a least square method at several phi angles on the coordinate system of specimen. Since the coefficients of these polynomials include these nine stress components mentioned above, it is possible to solve them as simultaneous equations. The calculating process of this method is simpler than that of the integral method. An X-ray plane stress problem was analyzed as an application of the present method, and the residual stress distribution on a shot-peened steel plate was actually measured by use of Cr-Kα X-rays to verify the analysis. The result showed that the compressive residual stress near the surface determined by the present method was smaller than the weighted average stress by the Sin 2 phi method because of the steep stress gradient. The present method is useful to obtain a reasonable value of stress for such a specimen with steep stress gradients near the surface. (author)

HammerCloud: A Stress Testing System for Distributed Analysis

CERN Document Server

van der Ster, Daniel C; Ubeda Garcia, Mario; Paladin, Massimo

2011-01-01

Distributed analysis of LHC data is an I/O-intensive activity which places large demands on the internal network, storage, and local disks at remote computing facilities. Commissioning and maintaining a site to provide an efficient distributed analysis service is therefore a challenge which can be aided by tools to help evaluate a variety of infrastructure designs and configurations. HammerCloud (HC) is one such tool; it is a stress testing service which is used by central operations teams, regional coordinators, and local site admins to (a) submit arbitrary number of analysis jobs to a number of sites, (b) maintain at a steady-state a predefined number of jobs running at the sites under test, (c) produce web-based reports summarizing the efficiency and performance of the sites under test, and (d) present a web-interface for historical test results to both evaluate progress and compare sites. HC was built around the distributed analysis framework Ganga, exploiting its API for grid job management. HC has been ...

Analysis of residual stress relief mechanisms in post-weld heat treatment

International Nuclear Information System (INIS)

Dong, Pingsha; Song, Shaopin; Zhang, Jinmiao

2014-01-01

This paper presents a recent study on weld residual stress relief mechanisms associated with furnace-based uniform post-weld heat treatment (PWHT). Both finite element and analytical methods are used to quantitatively examine how plastic deformation and creep relaxation contribute to residual stress relief process at different stages of PWHT process. The key contribution of this work to an improved understanding of furnace based uniform PWHT can be summarized as follows: (1)Plastic deformation induced stress relief during PWHT can be analytically expressed by the change in material elastic deformation capacity (or elastic deformation limit) measured in terms of material yield strength to Young's modulus ratio, which has a rather limited role in overall residual stress relief during furnace based uniform PWHT. (2)The most dominant stress relief mechanism is creep strain induced stress relaxation, as expected. However, a rapid creep strain development accompanied by a rapid residual stress reduction during heating stage before reaching PWHT temperature is shown to contribute to most of the stress relief seen in overall PWHT process, suggesting PWHT hold time can be significantly reduced as far as residual stress relief is concerned. (3)A simple engineering scheme for estimating residual stress reduction is proposed based on this study by relating material type, PWHT temperature, and component wall thickness. - Highlights: • The paper clarified effects of plastic deformation and creep relaxation on weld residual stress relief during uniform PWHT. • Creep strain development is far more important than plastic strain, mostly completed even before hold time starts. • Plastic strain development is insignificant and be analytically described by a material elastic deformation capacity parameter. • An engineering estimation scheme is proposed for determining residual stress reduction resulted from furnace based PWHT

A relative quantitative Methylation-Sensitive Amplified Polymorphism (MSAP) method for the analysis of abiotic stress.

Science.gov (United States)

Bednarek, Piotr T; Orłowska, Renata; Niedziela, Agnieszka

2017-04-21

We present a new methylation-sensitive amplified polymorphism (MSAP) approach for the evaluation of relative quantitative characteristics such as demethylation, de novo methylation, and preservation of methylation status of CCGG sequences, which are recognized by the isoschizomers HpaII and MspI. We applied the technique to analyze aluminum (Al)-tolerant and non-tolerant control and Al-stressed inbred triticale lines. The approach is based on detailed analysis of events affecting HpaII and MspI restriction sites in control and stressed samples, and takes advantage of molecular marker profiles generated by EcoRI/HpaII and EcoRI/MspI MSAP platforms. Five Al-tolerant and five non-tolerant triticale lines were exposed to aluminum stress using the physiologicaltest. Total genomic DNA was isolated from root tips of all tolerant and non-tolerant lines before and after Al stress following metAFLP and MSAP approaches. Based on codes reflecting events affecting cytosines within a given restriction site recognized by HpaII and MspI in control and stressed samples demethylation (DM), de novo methylation (DNM), preservation of methylated sites (MSP), and preservation of nonmethylatedsites (NMSP) were evaluated. MSAP profiles were used for Agglomerative hierarchicalclustering (AHC) based on Squared Euclidean distance and Ward's Agglomeration method whereas MSAP characteristics for ANOVA. Relative quantitative MSAP analysis revealed that both Al-tolerant and non-tolerant triticale lines subjected to Al stress underwent demethylation, with demethylation of CG predominating over CHG. The rate of de novo methylation in the CG context was ~3-fold lower than demethylation, whereas de novo methylation of CHG was observed only in Al-tolerant lines. Our relative quantitative MSAP approach, based on methylation events affecting cytosines within HpaII-MspI recognition sequences, was capable of quantifying de novo methylation, demethylation, methylation, and non-methylated status in control

State of charge estimation for lithium-ion pouch batteries based on stress measurement

International Nuclear Information System (INIS)

Dai, Haifeng; Yu, Chenchen; Wei, Xuezhe; Sun, Zechang

2017-01-01

State of charge (SOC) estimation is one of the important tasks of battery management system (BMS). Being different from other researches, a novel method of SOC estimation for pouch lithium-ion battery cells based on stress measurement is proposed. With a comprehensive experimental study, we find that, the stress of the battery during charge/discharge is composed of the static stress and the dynamic stress. The static stress, which is the measured stress in equilibrium state, corresponds to SOC, this phenomenon facilitates the design of our stress-based SOC estimation. The dynamic stress, on the other hand, is influenced by multiple factors including charge accumulation or depletion, current and historical operation, thus a multiple regression model of the dynamic stress is established. Based on the relationship between static stress and SOC, as well as the dynamic stress modeling, the SOC estimation method is founded. Experimental results show that the stress-based method performs well with a good accuracy, and this method offers a novel perspective for SOC estimation. - Highlights: • A State of Charge estimator based on stress measurement is proposed. • The stress during charge and discharge is investigated with comprehensive experiments. • Effects of SOC, current, and operation history on battery stress are well studied. • A multiple regression model of the dynamic stress is established.

Determinants of job stress in chemical process industry: A factor analysis approach.

Science.gov (United States)

Menon, Balagopal G; Praveensal, C J; Madhu, G

2015-01-01

Job stress is one of the active research domains in industrial safety research. The job stress can result in accidents and health related issues in workers in chemical process industries. Hence it is important to measure the level of job stress in workers so as to mitigate the same to avoid the worker's safety related problems in the industries. The objective of this study is to determine the job stress factors in the chemical process industry in Kerala state, India. This study also aims to propose a comprehensive model and an instrument framework for measuring job stress levels in the chemical process industries in Kerala, India. The data is collected through a questionnaire survey conducted in chemical process industries in Kerala. The collected data out of 1197 surveys is subjected to principal component and confirmatory factor analysis to develop the job stress factor structure. The factor analysis revealed 8 factors that influence the job stress in process industries. It is also found that the job stress in employees is most influenced by role ambiguity and the least by work environment. The study has developed an instrument framework towards measuring job stress utilizing exploratory factor analysis and structural equation modeling.

Finite-element formulations for the thermal stress analysis of two- and three-dimensional thin ractor structures

International Nuclear Information System (INIS)

Kulak, R.F.; Kennedy, J.M.; Belytschko, T.B.; Schoeberle, D.F.

1977-01-01

This paper describes finite-element formulations for the thermal stress analysis of LMFBR structures. The first formulation is applicable to large displacement rotation problems in which the strains are small. For this formulation, a general temperature-dependent constituent relationship is derived from a Gibbs potential function and a temperature dependent yield surface. The temperature dependency of the yield surface is based upon a temperature-dependent, material-hardening model. The model uses a temperature-equivalent stress-plastic strain diagram which is generated from isothermal uniaxial stress-strain data. A second formulation is presented for problems characterized by both large displacement-rotations and large strains. Here a set of large strain hypoelastic-plastic relationships are developed to linearly relate the rate of stress to the rate of deformation. The temperature field is described through time-dependent values at mesh node points; the temperature fields in each element are then obtained by interpolation formulas. Hence, problems with both spatial and temporal dependent temperature fields can easily be treated. The above developments were incorporated into two ANL developed finite-element computer codes: the implicit version of STRAW and the 3D Implicit Structural Analysis Code. STRAW is a two-dimensional code with a plane stress/plane strain beam element. The 3D Implicit code has a triangular flat plate element which is capable of sustaining both membrane and bending loads. To insure numerical stability both codes are based on an iterative-incremental solution procedure with equilibrium checks based on an error in energy

Research on stress distribution regularity of cement sheaths of radial well based on ABAQUS

Science.gov (United States)

Shi, Jihui; Cheng, Yuanfang; Li, Xiaolong; Xiao, Wen; Li, Menglai

2017-12-01

To ensure desirable outcome of hydraulic fracturing based on ultra-short radius radial systems, it is required to investigate the stress distribution regularity and stability of the cement sheath. On the basis of the theoretical model of the cement sheath stress distribution, a reservoir mechanical model was built using the finite element software, ABAQUS, according to the physical property of a certain oil reservoir of the Shengli oilfield. The stress distribution of the casing-cement-sheath-formation system under the practical condition was simulated, based on which analyses were conducted from multiple points of view. Results show that the stress on the internal interface of the cement sheath exceeds that on the external interface, and fluctuates with higher amplitudes, which means that the internal interface is the most failure-prone. The unevenness of the cement sheath stress distribution grows with the increasing horizontal principal stress ratio, and so does the variation magnitude. This indicates that higher horizontal principal stress ratios are unfavourable for the structural stability of the cement sheath. Both the wellbore quantity of the URRS and the physical property of the material can affect the cement sheath distribution. It is suggested to optimize the quantity of the radial wellbore and use cement with a lower elastic modulus and higher Poisson’s ratio. At last, the impact level of the above factor was analysed, with the help of the grey correlation analysis.

Thermal stress analysis of space shuttle orbiter wing skin panel and thermal protection system

Science.gov (United States)

Ko, William L.; Jenkins, Jerald M.

1987-01-01

Preflight thermal stress analysis of the space shuttle orbiter wing skin panel and the thermal protection system (TPS) was performed. The heated skin panel analyzed was rectangular in shape and contained a small square cool region at its center. The wing skin immediately outside the cool region was found to be close to the state of elastic instability in the chordwise direction based on the conservative temperature distribution. The wing skin was found to be quite stable in the spanwise direction. The potential wing skin thermal instability was not severe enough to tear apart the strain isolation pad (SIP) layer. Also, the preflight thermal stress analysis was performed on the TPS tile under the most severe temperature gradient during the simulated reentry heating. The tensile thermal stress induced in the TPS tile was found to be much lower than the tensile strength of the TPS material. The thermal bending of the TPS tile was not severe enough to cause tearing of the SIP layer.

A comparative study on stress and compliance based structural topology optimization

Science.gov (United States)

Hailu Shimels, G.; Dereje Engida, W.; Fakhruldin Mohd, H.

2017-10-01

Most of structural topology optimization problems have been formulated and solved to either minimize compliance or weight of a structure under volume or stress constraints, respectively. Even if, a lot of researches are conducted on these two formulation techniques separately, there is no clear comparative study between the two approaches. This paper intends to compare these formulation techniques, so that an end user or designer can choose the best one based on the problems they have. Benchmark problems under the same boundary and loading conditions are defined, solved and results are compared based on these formulations. Simulation results shows that the two formulation techniques are dependent on the type of loading and boundary conditions defined. Maximum stress induced in the design domain is higher when the design domains are formulated using compliance based formulations. Optimal layouts from compliance minimization formulation has complex layout than stress based ones which may lead the manufacturing of the optimal layouts to be challenging. Optimal layouts from compliance based formulations are dependent on the material to be distributed. On the other hand, optimal layouts from stress based formulation are dependent on the type of material used to define the design domain. High computational time for stress based topology optimization is still a challenge because of the definition of stress constraints at element level. Results also shows that adjustment of convergence criterions can be an alternative solution to minimize the maximum stress developed in optimal layouts. Therefore, a designer or end user should choose a method of formulation based on the design domain defined and boundary conditions considered.

Analysis of Deformation and Equivalent Stress during Biomass Material Compression Molding

Science.gov (United States)

Xu, Guiying; Wei, Hetao; Zhang, Zhien; Yu, Shaohui; Wang, Congzhe; Huang, Guowen

2018-02-01

Ansys is adopted to analyze mold deformation and stress field distribution rule during the process of compressing biomass under pressure of 20Mpa. By means of unit selection, material property setting, mesh partition, contact pair establishment, load and constraint applying, and solver setting, the stress and strain of overall mold are analyzed. Deformation and equivalent Stress of compression structure, base, mold, and compression bar were analyzed. We can have conclusions: The distribution of stress forced on compressor is not completely uniform, where the stress at base is slightly decreased; the stress and strain of compression bar is the largest, and stress concentration my occur at top of compression bar, which goes against compression bar service life; the overall deformation of main mold is smaller; although there is slight difference between upper and lower part, the overall variation is not obvious, but the stress difference between upper and lower part of main mold is extremely large so that reaches to 10 times; the stress and strain in base decrease in circular shape, but there is still stress concentration in ledge, which goes against service life; contact stress does not distribute uniformly, there is increasing or decreasing trend in adjacent parts, which is very large in some parts. in constructing both.

Stress analysis for robot arm version 2

International Nuclear Information System (INIS)

Anwar Abdul Rahman; Fikri, A.; Salleh, M. S.; Mohd Arif Hamzah; Azraf Azman; Rosli Darmawan; Mohd Rizal Mamat

2010-01-01

The design of a robot needs to be analyzed to ensure the specification and requirement by the user is full filled. Therefore, stress analysis has been performed on the robot arm version 2 after its complete fabrication. This paper discusses the result of the analysis and proposed measures to improve the future design of robot arm. (author)

The Mathematical and Computer Aided Analysis of the Contact Stress of the Surface With 4th Order

Science.gov (United States)

Huran, Liu

Inspired from some gears with heavy power transmission in practical usage after serious plastic deformation in metallurgical industry, we believe that there must existed some kind of gear profile which is most suitable in both the contact and bending fatigue strength. From careful analysis and deep going investigation, we think that it is the profile of equal conjugate curvature with high order of contact, and analyzed the forming principle of this kind of profile. Based on the second curve and comparative analysis of fourth order curves, combined with Chebyshev polynomial terms of higher order contact with tooth contact stress formula derived. Note high exposure in the case of two extreme points of stress and extreme positions and the derived extreme contact stress formula. Finally, a pair of conjugate gear tooth profile curvature provides specific contact stress calculation.

Polymer-based stress sensor with integrated readout

DEFF Research Database (Denmark)

Thaysen, Jacob; Yalcinkaya, Arda Deniz; Vettiger, P.

2002-01-01

softer than silicon and that a gold resistor is easily incorporated in SU-8, we have proven that a SU-8-based cantilever sensor is almost as sensitive to stress changes as the silicon piezoresistive cantilever. First, the surface stress sensing principle is discussed, from which it can be shown......, noise and device failure. The characterization shows that there is a good agreement between the expected and the obtained performance....

Stress analysis and evaluation of a rectangular pressure vessel

International Nuclear Information System (INIS)

Rezvani, M.A.; Ziada, H.H.; Shurrab, M.S.

1992-10-01

This study addresses structural analysis and evaluation of an abnormal rectangular pressure vessel, designed to house equipment for drilling and collecting samples from Hanford radioactive waste storage tanks. It had to be qualified according to ASME boiler and pressure vessel code, Section VIII; however, it had the cover plate bolted along the long face, a configuration not addressed by the code. Finite element method was used to calculate stresses resulting from internal pressure; these stresses were then used to evaluate and qualify the vessel. Fatigue is not a concern; thus, it can be built according to Section VIII, Division I instead of Division 2. Stress analysis was checked against the code. A stayed plate was added to stiffen the long side of the vessel

Supervised machine learning algorithms to diagnose stress for vehicle drivers based on physiological sensor signals.

Science.gov (United States)

Barua, Shaibal; Begum, Shahina; Ahmed, Mobyen Uddin

2015-01-01

Machine learning algorithms play an important role in computer science research. Recent advancement in sensor data collection in clinical sciences lead to a complex, heterogeneous data processing, and analysis for patient diagnosis and prognosis. Diagnosis and treatment of patients based on manual analysis of these sensor data are difficult and time consuming. Therefore, development of Knowledge-based systems to support clinicians in decision-making is important. However, it is necessary to perform experimental work to compare performances of different machine learning methods to help to select appropriate method for a specific characteristic of data sets. This paper compares classification performance of three popular machine learning methods i.e., case-based reasoning, neutral networks and support vector machine to diagnose stress of vehicle drivers using finger temperature and heart rate variability. The experimental results show that case-based reasoning outperforms other two methods in terms of classification accuracy. Case-based reasoning has achieved 80% and 86% accuracy to classify stress using finger temperature and heart rate variability. On contrary, both neural network and support vector machine have achieved less than 80% accuracy by using both physiological signals.

Traumatic stress and accelerated DNA methylation age: A meta-analysis.

Science.gov (United States)

Wolf, Erika J; Maniates, Hannah; Nugent, Nicole; Maihofer, Adam X; Armstrong, Don; Ratanatharathorn, Andrew; Ashley-Koch, Allison E; Garrett, Melanie; Kimbrel, Nathan A; Lori, Adriana; Va Mid-Atlantic Mirecc Workgroup; Aiello, Allison E; Baker, Dewleen G; Beckham, Jean C; Boks, Marco P; Galea, Sandro; Geuze, Elbert; Hauser, Michael A; Kessler, Ronald C; Koenen, Karestan C; Miller, Mark W; Ressler, Kerry J; Risbrough, Victoria; Rutten, Bart P F; Stein, Murray B; Ursano, Robert J; Vermetten, Eric; Vinkers, Christiaan H; Uddin, Monica; Smith, Alicia K; Nievergelt, Caroline M; Logue, Mark W

2018-06-01

Recent studies examining the association between posttraumatic stress disorder (PTSD) and accelerated aging, as defined by DNA methylation-based estimates of cellular age that exceed chronological age, have yielded mixed results. We conducted a meta-analysis of trauma exposure and PTSD diagnosis and symptom severity in association with accelerated DNA methylation age using data from 9 cohorts contributing to the Psychiatric Genomics Consortium PTSD Epigenetics Workgroup (combined N = 2186). Associations between demographic and cellular variables and accelerated DNA methylation age were also examined, as was the moderating influence of demographic variables. Meta-analysis of regression coefficients from contributing cohorts revealed that childhood trauma exposure (when measured with the Childhood Trauma Questionnaire) and lifetime PTSD severity evidenced significant, albeit small, meta-analytic associations with accelerated DNA methylation age (ps = 0.028 and 0.016, respectively). Sex, CD4T cell proportions, and natural killer cell proportions were also significantly associated with accelerated DNA methylation age (all ps age. There was no evidence of moderation of the trauma or PTSD variables by demographic factors. Results suggest that traumatic stress is associated with advanced epigenetic age and raise the possibility that cells integral to immune system maintenance and responsivity play a role in this. This study highlights the need for additional research into the biological mechanisms linking traumatic stress to accelerated DNA methylation age and the importance of furthering our understanding of the neurobiological and health consequences of PTSD. Published by Elsevier Ltd.

Stress determination and geomechanical stability analysis of an oil ...

Indian Academy of Sciences (India)

Practical data including geomechanical parameters along with drilling data from one of Iranian oilfields, Mansouri-54 well have been utilized in this analysis. in situ stress was determined using stress polygon method and conducting hydraulic fracturing data in the field. Analytical solution using the Mogi–Coulomb and the ...

Construction of finite element model and stress analysis of anterior cruciate ligament tibial insertion.

Science.gov (United States)

Dai, Can; Yang, Liu; Guo, Lin; Wang, Fuyou; Gou, Jingyue; Deng, Zhilong

2015-01-01

The aim of the present study was to develop a more realistic finite element (FE) model of the human anterior cruciate ligament (ACL) tibial insertion and to analyze the stress distribution in the ACL internal fibers under load. The ACL tibial insertions were processed histologically. With Photoshop software, digital images taken from the histological slides were collaged, contour lines were drawn, and different gray values were filled based on the structure. The data were exported to Amira software and saved as ".hmascii" file. This document was imported into HyperMesh software. The solid mesh model generated using HyperMesh software was imported into Abaqus software. The material properties were introduced, boundary conditions were set, and load was added to carry out the FE analysis. The stress distribution of the ACL internal fibers was uneven. The lowest stress could be observed in the ACL lateral fibers under tensile and shear load. The establishment of ACL tibial insertion FE model and mechanical analysis could reveal the stress distribution in the ACL internal fibers under load. There was greater load carrying capacity in the ACL lateral fibers which could sustain greater tensile and shear forces.

Thermal stress analysis of a planar SOFC stack

Science.gov (United States)

Lin, Chih-Kuang; Chen, Tsung-Ting; Chyou, Yau-Pin; Chiang, Lieh-Kwang

The aim of this study is, by using finite element analysis (FEA), to characterize the thermal stress distribution in a planar solid oxide fuel cell (SOFC) stack during various stages. The temperature profiles generated by an integrated thermo-electrochemical model were applied to calculate the thermal stress distributions in a multiple-cell SOFC stack by using a three-dimensional (3D) FEA model. The constructed 3D FEA model consists of the complete components used in a practical SOFC stack, including positive electrode-electrolyte-negative electrode (PEN) assembly, interconnect, nickel mesh, and gas-tight glass-ceramic seals. Incorporation of the glass-ceramic sealant, which was never considered in previous studies, into the 3D FEA model would produce more realistic results in thermal stress analysis and enhance the reliability of predicting potential failure locations in an SOFC stack. The effects of stack support condition, viscous behavior of the glass-ceramic sealant, temperature gradient, and thermal expansion mismatch between components were characterized. Modeling results indicated that a change in the support condition at the bottom frame of the SOFC stack would not cause significant changes in thermal stress distribution. Thermal stress distribution did not differ significantly in each unit cell of the multiple-cell stack due to a comparable in-plane temperature profile. By considering the viscous characteristics of the glass-ceramic sealant at temperatures above the glass-transition temperature, relaxation of thermal stresses in the PEN was predicted. The thermal expansion behavior of the metallic interconnect/frame had a greater influence on the thermal stress distribution in the PEN than did that of the glass-ceramic sealant due to the domination of interconnect/frame in the volume of a planar SOFC assembly.

Analytical Solution of Tunnel Surrounding Rock for Stress and Displacement Based on Lade–Duncan Criterion

Directory of Open Access Journals (Sweden)

MingZheng Zhu

2018-01-01

Full Text Available The deformation and failure of tunnel surrounding rock is the result of tunnel excavation disturbance and rock stress release. When the local stress of surrounding rock exceeds the elastic limit of rock mass, the plastic analysis of surrounding rock must be carried out to judge the stability of tunnel. In this study, the Lade–Duncan yield criterion is used to calculate the analytic solutions for the surrounding rock in a tunnel, and the radius and displacement of the plastic zone are deduced using an equilibrium equation. The plastic zone radius and displacement based on Lade–Duncan criterion and Mohr–Coulomb criterion were compared by using single-factor analysis method under the different internal friction angles, in situ stresses, and support resistances. The results show that the solutions of the radius and displacement of plastic zone calculated by the Lade–Duncan criterion are close to those of Mohr–Coulomb criterion under the high internal friction angle and support resistance or low in situ rock stress; however, the radius and displacement of the plastic zone calculated by the Lade–Duncan criterion are larger under normal circumstances, and the Lade–Duncan criterion is more applicable to the stability analysis of the surrounding rock in a tunnel.

A Procedure for 3-D Contact Stress Analysis of Spiral Bevel Gears

Science.gov (United States)

Kumar, A.; Bibel, G.

1994-01-01

Contact stress distribution of spiral bevel gears using nonlinear finite element static analysis is presented. Procedures have been developed to solve the nonlinear equations that identify the gear and pinion surface coordinates based on the kinematics of the cutting process and orientate the pinion and the gear in space to mesh with each other. Contact is simulated by connecting GAP elements along the intersection of a line from each pinion point (parallel to the normal at the contact point) with the gear surface. A three dimensional model with four gear teeth and three pinion teeth is used to determine the contact stresses at two different contact positions in a spiral bevel gearset. A summary of the elliptical contact stress distribution is given. This information will be helpful to helicopter and aircraft transmission designers who need to minimize weight of the transmission and maximize reliability.

Motion and Stress Analysis of Cam System for Marine Diesel Engine 93 KW

Directory of Open Access Journals (Sweden)

Christian Dhani Setiawan

2017-01-01

Full Text Available The developments of maritime sector in Indonesia shows increasing demand for ships. Especially ships with size of 30 GT has problem with low availability of the ship engine, which most of the ships still use non marine diesel engine as its main propulsion. The problem gives interest to make a step to improve by design marine diesel engine using reverse engineering method. Cam system of marine diesel engine design was needed to be calculate to select the material and the motion. The design of cam system needs study about the stress analysis in cam system to make sure the distribution of force and moment. The result of stress analysis was used to select material of components in cam system. The motion analysis result was used to be input data of stress analysis. The condition to obtain the stress of components was on maximum condition, its contain pressure, torque, rotation, and force. All component that calculated are camshaft, lifter (flat-tappet, push rod, rocker arm, spring, and valve. Each component was given two different materials and material selection was based on safety factor of each component. Material for camshaft and lifter were malleable cast iron, for push rod and rocker arm were mild steel, for spring was ASTM A231, for intake valve was steel JIS SUH3, and for exhaust valve was steel JIS SUH35. The result of motion analysis were angular velocity of camshaft with value was 2400 deg/sec, friction force between camshaft and lifter with maximum value was 125.393 N, and contact force between camshaft and lifter with maximum value was 845.307 N, and linear velocity of intake valve with maximum value was 696.573 mm/s, and linear velocity of exhaust valve was 463.734 mm/s.

The mediating effect of sleep satisfaction on the relationship between stress and perceived health of adolescents suffering atopic disease: Secondary analysis of data from the 2013 9th Korea Youth Risk Behavior Web-based Survey.

Science.gov (United States)

Oh, Won Oak; Im, YeoJin; Suk, Min Hyun

2016-11-01

Difficulty in sleep is one disturbing symptom in adolescents with atopic diseases including asthma, allergic rhinitis, and atopic dermatitis. Assuming psychological stress can affect adolescents' health status, impaired sleep quality can be one mediator that negatively impacts the health status of adolescents with atopic disease. This study aimed to identify the mediating effect of sleep satisfaction on the relationship between stress and perceived health status in Korean adolescents with atopic disease and to examine the differences among three types of atopic disease. A cross-sectional descriptive study was completed based on secondary analysis of raw data from the 2013 9th Korea Youth Risk Behavior Web-based Survey. The 21,154 adolescents (29.2%) ever diagnosed and treated for at least one atopic disease regardless of the symptom presence in a recent year were extracted out of 72,435 survey participants. Then, the 13,216 individuals with exclusively single atopic diseases were included in analyzing the mediation model. Variables including demographics, stress, perceived health status, and sleep satisfaction were included. Pearson correlation, one-way ANOVA, path analysis to define direct/indirect effects with bootstrapping analysis, and multi-group variance analysis were conducted. High levels of stress in adolescents with atopic diseases had a significant and direct effect on their negative health status perception for all atopic disease groups. A significant negative mediating effect of sleep satisfaction was identified on the relationship between stress and perceived health status, irrespective of the type of atopic disease. Total effect and remaining direct effect on the path from stress and perceived health status via sleep satisfaction was high in adolescents with atopic dermatitis and allergic rhinitis compared to those with asthma. To improve sleep satisfaction for adolescents with atopic diseases, interventions are needed to enhance the adolescents

On the influence of T-Stress on photoelastic analysis under pure mode II loading

Directory of Open Access Journals (Sweden)

Chiara Colombo

2008-01-01

Full Text Available According to the classical definition for in-plane modes of crack deformation, the constant stress term T exists only in the presence of mode I. However, recent studies show that this term can exist inmode II conditions as well, and significantly affect the elastic stress field around the crack tip. These effects can be visualized using the experimental method of photoelasticity. Based on the analytical studies, presence of the T-stress in mode II cracks transforms the isochromatic fringe patterns from symmetric closed loops to asymmetric and discontinuous shapes. In this paper, presence of the T-stress in mode II cracks and its effects on the fringe patterns is experimentally investigated. The test specimens are Brazilian disks containing very sharp central cracks: experimental results indicate that these specimens contain negative values of T-stress. Experimental values are then compared to numerical results. To better understand the differences between experimental and numerical values, a thee dimensional analysis is performed with the finite element method: results show the influence of the real geometry of the crack front on the stress intensity factors.

Diffraction stress analysis of thin films; investigating elastic grain interaction

International Nuclear Information System (INIS)

Kumar, A.

2005-12-01

This work is dedicated to the investigation of specimens exhibiting anisotropic microstructures (and thus macroscopic elastic anisotropy) and/or inhomogeneous microstructures, as met near surfaces and in textured materials. The following aspects are covered: (i) Analysis of specimens with direction-dependent (anisotropic) elastic grain-interaction. Elastic grain-interaction determines the distribution of stresses and strains over the (crystallographically) differently oriented grains of a mechanically stressed polycrystal and the mechanical and diffraction (X-ray) elastic constants (relating (diffraction) lattice strains to mechanical stresses). Grain interaction models that allow for anisotropic, direction-dependent grain interaction have been developed very recently. The notion 'direction-dependent' grain-interaction signifies that different grain-interaction constraints prevail along different directions in a specimen. Practical examples of direction-dependent grain interaction are the occurrence of surface anisotropy in thin films and the surface regions of bulk polycrystals and the occurrence of grain-shape (morphological) texture. In this work, for the first time, stress analyses of thin films have been performed on the basis of these newly developed grain-interaction models. It has also been demonstrated that the identification of the (dominant) source of direction-dependent grain interaction is possible. The results for the grain interaction have been discussed in the light of microstructural investigations of the specimens by microscopic techniques. (ii) Analysis of specimens with depth gradients: Diffraction stress analysis can be hindered if gradients of the stress state, the composition or the microstructure occur in the specimen under investigation, as the so-called information depth varies in the course of a traditional stress measurement: Ambiguous results are thus generally obtained. In this work, a strategy for stress measurements at fixed

Method for analysis and assessment of the relation between stress and reliability of knowledge-based actions in the probabilistic safety analysis; Methode fuer die Analyse und Bewertung der Wechselwirkung zwischen Stress und der Zuverlaessigkeit wissensbasierten Handelns in der probabilistischen Sicherheitsanalyse

Energy Technology Data Exchange (ETDEWEB)

Fassmann, Werner

2014-06-15

According to the current theoretical and empirical state-of-the-art, stress has to be understood as the emotional and cognitive reaction by which humans adapt to situations which imply real or imagined danger, threat, or frustration of important personal goals or needs. The emotional reaction to such situations can be so extreme that rational coping with the situation will be precluded. In less extreme cases, changes of cognitive processes underlying human action will occur, which may systematically affect the reliability of tasks personnel has to perform in a stressful situation. Reliable task performance by personnel of nuclear power plants and other risk technologies is also affected by such effects. The method developed in the frame of the research and development project RS1198 sponsored by the German Federal Ministry for Economic Affairs and Energy (BMWi) addresses both aspects of emotional and cognitive coping with stressful situations. Analytical and evaluation steps of the approach provide guidance to the end users on how to capture and quantify the contribution of stress-related emotional and cognitive factors to the reliable performance of knowledge-based actions. For this purpose, a suitable guideline has been developed. Further research for clarifying open questions has been identified. A case study application illustrates how to use the method. Part of the work performed in this project was dedicated to a review addressing the question to which extent Swain's approach to the analysis and evaluation of stress is in line with current scientific knowledge. Suitable suggestions for updates have been developed.

Evaluation of a Web-Based Holistic Stress Reduction Pilot Program Among Nurse-Midwives.

Science.gov (United States)

Wright, Erin M

2018-06-01

Work-related stress among midwives results in secondary traumatic stress, posttraumatic stress disorder, and job attrition. The purpose of this pilot project was to evaluate the effectiveness of a holistic, web-based program using holistic modalities for stress reduction and improved coping among certified nurse-midwives. A convenience sample of 10 midwives participated in a web-based holistic stress reduction intervention using yoga, mindfulness-based stress reduction, and meditation for four days each week over 4 weeks. Participants completed pre- and postintervention questionnaires (Perceived Stress Scale [PSS] and the Coping Self-Efficacy Scale [CSES]) for evaluation of effectiveness. The PSS means showed improvement in midwives' stress (16.4-12.3). The CSES means showed improvement in coping (174.8-214.5). Improvement was shown in each subscale of the CSES ("uses problem-focused coping": 19.2%; "stops unpleasant thoughts and emotions": 20.3%; and "gets support from family and friends": 16.6%). Findings suggest the potential for stress reduction and improved coping skills after using holistic techniques in a web-based format within a cohort of nurse-midwives. Further research of web-based, holistic intervention for stress reduction among midwives is warranted.

Contact Stress Analysis for Gears of Different Helix Angle Using Finite Element Method

Directory of Open Access Journals (Sweden)

Patil Santosh

2014-07-01

Full Text Available The gear contact stress problem has been a great point of interest for many years, but still an extensive research is required to understand the various parameters affecting this stress. Among such parameters, helix angle is one which has played a crucial role in variation of contact stress. Numerous studies have been carried out on spur gear for contact stress variation. Hence, the present work is an attempt to study the contact stresses among the helical gear pairs, under static conditions, by using a 3D finite element method. The helical gear pairs on which the analysis is carried are 0, 5, 15, 25 degree helical gear sets. The Lagrange multiplier algorithm has been used between the contacting pairs to determine the stresses. The helical gear contact stress is evaluated using FE model and results have also been found at different coefficient of friction, varying from 0.0 to 0.3. The FE results have been further compared with the analytical calculations. The analytical calculations are based upon Hertz and AGMA equations, which are modified to include helix angle. The commercial finite element software was used in the study and it was shown that this approach can be applied to gear design efficiently. The contact stress results have shown a decreasing trend, with increase in helix angle.

Smartphone-Based Self-Assessment of Stress in Healthy Adult Individuals

DEFF Research Database (Denmark)

Þórarinsdóttir, Helga; Kessing, Lars Vedel; Faurholt-Jepsen, Maria

2017-01-01

BACKGROUND: Stress is a common experience in today's society. Smartphone ownership is widespread, and smartphones can be used to monitor health and well-being. Smartphone-based self-assessment of stress can be done in naturalistic settings and may potentially reflect real-time stress level...

Finite element modelling for fatigue stress analysis of large suspension bridges

Science.gov (United States)

Chan, Tommy H. T.; Guo, L.; Li, Z. X.

2003-03-01

Fatigue is an important failure mode for large suspension bridges under traffic loadings. However, large suspension bridges have so many attributes that it is difficult to analyze their fatigue damage using experimental measurement methods. Numerical simulation is a feasible method of studying such fatigue damage. In British standards, the finite element method is recommended as a rigorous method for steel bridge fatigue analysis. This paper aims at developing a finite element (FE) model of a large suspension steel bridge for fatigue stress analysis. As a case study, a FE model of the Tsing Ma Bridge is presented. The verification of the model is carried out with the help of the measured bridge modal characteristics and the online data measured by the structural health monitoring system installed on the bridge. The results show that the constructed FE model is efficient for bridge dynamic analysis. Global structural analyses using the developed FE model are presented to determine the components of the nominal stress generated by railway loadings and some typical highway loadings. The critical locations in the bridge main span are also identified with the numerical results of the global FE stress analysis. Local stress analysis of a typical weld connection is carried out to obtain the hot-spot stresses in the region. These results provide a basis for evaluating fatigue damage and predicting the remaining life of the bridge.

Use of an X-ray imaging plate for stress analysis

International Nuclear Information System (INIS)

Schubert, A.; Kaempfe, B.; Ermrich, M.; Auerswald, E.; Traenkner, K.

1994-01-01

The X-ray diffraction method for stress measurements has been successfully carried out for many years [1]. The basis for the determination of residual and load stresses is the Debye-Scherrer-method and Bragg's law. The Bragg angles of one or several reflections are measured with high precision in the back reflection region. The results permit the determination of changes in interplanar spacings of polycrystalline materials. Conventional stress analysis is based on two commonly used techniques, the so-called ''sin 2 ψ''- and ''φ''-methods, which require measurements at different tilting and rotating positions of the sample by the help of a Ψ- or Ω-goniometer [1, 2, 3]. In these cases the interplanar spacings and consequently the shift of the peak can be determined with conventional counters or position sensitive detectors. From the whole diffraction cone only a small part of lattice planes {hkl} with a special orientation (ψ, φ) is analysed. The use of a two-dimensional detector like an imaging plate [4] offers the possibility to get diffraction patterns in one measurement from lattice planes {hkl} having one ψ and all φ orientations (non-tilted case) or different ψ and different φ orientations (tilted case). Thus the number of measurements for the calculation of the stress components can be significantly reduced. Further it is possible to investigate both textured materials and coarse-grained samples. (orig.)

Residual stresses analysis in ball end milling of nickel-based superalloy Inconel 718

Energy Technology Data Exchange (ETDEWEB)

Wang, Junteng; Zhang, Dinghua; Wu, Baohai; Luo, Ming [Key Laboratory of Contemporary Design and Integrated Manufacturing Technology, Northwestern Polytechnical University (China)

2017-11-15

Inconel 718 is widely used in the aviation, space, automotive and biomedical industries because of its outstanding properties. Near-surface residual stresses that are induced by ball end milling in Inconel 718 can be crucial for the performance and service time of the machined parts. In this paper, the influences of cutting conditions, including the use of cutting parameters, cutting fluid and spindle angles, on the residual stresses in the ball end milling process of Inconel 718 alloy were investigated experimentally. X-ray diffraction measurements reveal that residual stress distributions are highly influenced by cutting parameters, especially the depth of cut and cutting speed. The milling operation with cooling induces more compressive stresses trend and the magnitude of the residual stresses increases in the tensile direction with the increase of spindle angles. These cutting induced effects were further discussed with respect to thermal- mechanical coupling theory and some observations made by optical microscopy. From this investigation, it is suggested that the machining process parameters are not the smaller the better for the control of residual stresses in the ball end milling process of Inconel 718. (author)

An automated data management/analysis system for space shuttle orbiter tiles. [stress analysis

Science.gov (United States)

Giles, G. L.; Ballas, M.

1982-01-01

An engineering data management system was combined with a nonlinear stress analysis program to provide a capability for analyzing a large number of tiles on the space shuttle orbiter. Tile geometry data and all data necessary of define the tile loads environment accessed automatically as needed for the analysis of a particular tile or a set of tiles. User documentation provided includes: (1) description of computer programs and data files contained in the system; (2) definitions of all engineering data stored in the data base; (3) characteristics of the tile anaytical model; (4) instructions for preparation of user input; and (5) a sample problem to illustrate use of the system. Description of data, computer programs, and analytical models of the tile are sufficiently detailed to guide extension of the system to include additional zones of tiles and/or additional types of analyses

Stress Analysis in Polymeric Coating Layer Deposited on Rigid Substrate

Energy Technology Data Exchange (ETDEWEB)

Lee, Sang Soon Lee [Korea University of Technology and Education, School of Mechatronics Engineering, Chonan (Korea, Republic of)

2015-08-15

This paper presents an analysis of thermal stress induced along the interface between a polymeric coating layer and a steel substrate as a result of uniform temperature change. The epoxy layer is assumed to be a linear viscoelastic material and to be theromorheologically simple. The viscoelastic boundary element method is employed to investigate the behavior of interface stresses. The numerical results exhibit relaxation of interface stresses and large stress gradients, which are observed in the vicinity of the free surface. Since the exceedingly large stresses cannot be borne by the polymeric coating layer, local cracking or delamination can occur at the interface corner.

Evaluation of Stress Parameters Based on Heart Rate Variability Measurements

OpenAIRE

Uysal, Fatma; Tokmakçı, Mahmut

2018-01-01

In this study, heart rate variabilitymeasurements and analysis was carried with help of the ECG recordings to showhow autonom nervous system activity changes. So as to evaluate the parametersrelated to stress of the study, the situation of relaxation, Stroop color/wordtest, mental test and auditory stimulus that would stress someone out wereapplied to six volunteer participants in a laboratory environment. Being takentotally seven minutes ECG recording and made analysis in time and frequencyd...

Genotypic Correlation and Path Analysis of Some Traits related to Oil Yield and Grain Yield in Canola (Brassica napus L. under Non-stress and Water Deficit Stress Conditions

Directory of Open Access Journals (Sweden)

A Ismaili

2017-03-01

Full Text Available Introduction Obtaining varieties with acceptable yield and tolerant to different arid and semi-arid climate condition of Iran is an important goal in canola breeding programs. Selection of genotypes base on one or more traits without regarding to correlation between them, could biases the expected results. Therefore, identifying of genetic correlation among traits especially in environmental stress condition is very important. The use of genotypic correlation helps evaluating the magnitude and direction of associations between characters facilitating the application of indirect selection, because genetic changes in a given trait may change other traits, leading to faster and larger genetic gains in plant breeding programs. Therefore, the selection for another trait may result in indirect response in the low heritable trait, provided the following conditions are satisfied: the genetic correlation between them is substantial, and the heritability of the secondary trait is greater than that of the primary trait. The purpose of this study was estimating the total genotypic variability, genotypic correlations, and path analysis among some important traits for selection criteria for improving seed and oil yield in canola under water deficit stress condition. Materials and Methods For evaluation of genetic correlation among traits and identifying important affecting traits on grain yield and oil yield in canola genotypes, an experiment was conducted based on a randomized complete blocks design with three replications in two different conditions of water deficit (stress and non-stress. Different traits were measured including seed yield, 1000-seed weight, number of seeds per pod, number of pods per plant, silique length, oil content, days to maturity, protein content, plant height and water use efficiency. Genotypic and phenotypic correlation coefficients were calculated for ten characters during growing seasons. The genotypic correlation coefficients

Genome-Wide Identification and Expression Analysis of WRKY Transcription Factors under Multiple Stresses in Brassica napus.

Science.gov (United States)

He, Yajun; Mao, Shaoshuai; Gao, Yulong; Zhu, Liying; Wu, Daoming; Cui, Yixin; Li, Jiana; Qian, Wei

2016-01-01

WRKY transcription factors play important roles in responses to environmental stress stimuli. Using a genome-wide domain analysis, we identified 287 WRKY genes with 343 WRKY domains in the sequenced genome of Brassica napus, 139 in the A sub-genome and 148 in the C sub-genome. These genes were classified into eight groups based on phylogenetic analysis. In the 343 WRKY domains, a total of 26 members showed divergence in the WRKY domain, and 21 belonged to group I. This finding suggested that WRKY genes in group I are more active and variable compared with genes in other groups. Using genome-wide identification and analysis of the WRKY gene family in Brassica napus, we observed genome duplication, chromosomal/segmental duplications and tandem duplication. All of these duplications contributed to the expansion of the WRKY gene family. The duplicate segments that were detected indicated that genome duplication events occurred in the two diploid progenitors B. rapa and B. olearecea before they combined to form B. napus. Analysis of the public microarray database and EST database for B. napus indicated that 74 WRKY genes were induced or preferentially expressed under stress conditions. According to the public QTL data, we identified 77 WRKY genes in 31 QTL regions related to various stress tolerance. We further evaluated the expression of 26 BnaWRKY genes under multiple stresses by qRT-PCR. Most of the genes were induced by low temperature, salinity and drought stress, indicating that the WRKYs play important roles in B. napus stress responses. Further, three BnaWRKY genes were strongly responsive to the three multiple stresses simultaneously, which suggests that these 3 WRKY may have multi-functional roles in stress tolerance and can potentially be used in breeding new rapeseed cultivars. We also found six tandem repeat pairs exhibiting similar expression profiles under the various stress conditions, and three pairs were mapped in the stress related QTL regions

Genome-Wide Identification and Expression Analysis of WRKY Transcription Factors under Multiple Stresses in Brassica napus.

Directory of Open Access Journals (Sweden)

Yajun He

Full Text Available WRKY transcription factors play important roles in responses to environmental stress stimuli. Using a genome-wide domain analysis, we identified 287 WRKY genes with 343 WRKY domains in the sequenced genome of Brassica napus, 139 in the A sub-genome and 148 in the C sub-genome. These genes were classified into eight groups based on phylogenetic analysis. In the 343 WRKY domains, a total of 26 members showed divergence in the WRKY domain, and 21 belonged to group I. This finding suggested that WRKY genes in group I are more active and variable compared with genes in other groups. Using genome-wide identification and analysis of the WRKY gene family in Brassica napus, we observed genome duplication, chromosomal/segmental duplications and tandem duplication. All of these duplications contributed to the expansion of the WRKY gene family. The duplicate segments that were detected indicated that genome duplication events occurred in the two diploid progenitors B. rapa and B. olearecea before they combined to form B. napus. Analysis of the public microarray database and EST database for B. napus indicated that 74 WRKY genes were induced or preferentially expressed under stress conditions. According to the public QTL data, we identified 77 WRKY genes in 31 QTL regions related to various stress tolerance. We further evaluated the expression of 26 BnaWRKY genes under multiple stresses by qRT-PCR. Most of the genes were induced by low temperature, salinity and drought stress, indicating that the WRKYs play important roles in B. napus stress responses. Further, three BnaWRKY genes were strongly responsive to the three multiple stresses simultaneously, which suggests that these 3 WRKY may have multi-functional roles in stress tolerance and can potentially be used in breeding new rapeseed cultivars. We also found six tandem repeat pairs exhibiting similar expression profiles under the various stress conditions, and three pairs were mapped in the stress related

Presenteeism, stress resilience, and physical activity in older manual workers: a person-centred analysis.

Science.gov (United States)

Thogersen-Ntoumani, Cecilie; Black, Julie; Lindwall, Magnus; Whittaker, Anna; Balanos, George M

2017-12-01

This study used a person-centred approach to explore typologies of older manual workers based on presenteeism, stress resilience, and physical activity. Older manual workers ( n  = 217; 69.1% male; age range 50-77; M age = 57.11 years; SD = 5.62) from a range of UK-based organisations, representing different manual job roles, took part in the study. A cross-sectional survey design was used. Based on the three input variables: presenteeism, stress resilience and physical activity, four distinct profiles were identified on using Latent Profile Analysis. One group ('High sport/exercise and well-functioning'; 5.50%) engaged in high levels of sport/exercise and exhibited low levels of stress resilience and all types of presenteeism. Another profile ('Physically burdened'; 9.70%) reported high levels of work and leisure-time physical activity, low stress resilience, as well as high levels of presenteeism due to physical and time demands. A 'Moderately active and functioning' group (46.50%) exhibited moderate levels on all variables. Finally, the fourth profile ('Moderately active with high presenteeism'; 38.20%) reported engaging in moderate levels of physical activity and had relatively high levels of stress resilience, yet also high levels of presenteeism. The profiles differed on work affect and health perceptions largely in the expected directions. There were no differences between the profiles in socio-demographics. These results highlight complex within-person interactions between presenteeism, stress resilience, and physical activity in older manual workers. The identification of profiles of older manual workers who are at risk of poor health and functioning may inform targeted interventions to help retain them in the workforce for longer.

Effect of abiotic and biotic stress factors analysis using machine learning methods in zebrafish.

Science.gov (United States)

Gutha, Rajasekar; Yarrappagaari, Suresh; Thopireddy, Lavanya; Reddy, Kesireddy Sathyavelu; Saddala, Rajeswara Reddy

2018-03-01

In order to understand the mechanisms underlying stress responses, meta-analysis of transcriptome is made to identify differentially expressed genes (DEGs) and their biological, molecular and cellular mechanisms in response to stressors. The present study is aimed at identifying the effect of abiotic and biotic stress factors, and it is found that several stress responsive genes are common for both abiotic and biotic stress factors in zebrafish. The meta-analysis of micro-array studies revealed that almost 4.7% i.e., 108 common DEGs are differentially regulated between abiotic and biotic stresses. This shows that there is a global coordination and fine-tuning of gene regulation in response to these two types of challenges. We also performed dimension reduction methods, principal component analysis, and partial least squares discriminant analysis which are able to segregate abiotic and biotic stresses into separate entities. The supervised machine learning model, recursive-support vector machine, could classify abiotic and biotic stresses with 100% accuracy using a subset of DEGs. Beside these methods, the random forests decision tree model classified five out of 8 stress conditions with high accuracy. Finally, Functional enrichment analysis revealed the different gene ontology terms, transcription factors and miRNAs factors in the regulation of stress responses. Copyright © 2017 Elsevier Inc. All rights reserved.

Stress analysis of advanced attack helicopter composite main rotor blade root end lug

Science.gov (United States)

Baker, D. J.

1982-01-01

Stress analysis of the Advanced Attack Helicopter (AAH) composite main rotor blade root end lug is described. The stress concentration factor determined from a finite element analysis is compared to an empirical value used in the lug design. The analysis and test data indicate that the stress concentration is primarily a function of configuration and independent of the range of material properties typical of Kevlar-49/epoxy and glass epoxy.

Inserting Stress Analysis of Combined Hexagonal Aluminum Honeycombs

Directory of Open Access Journals (Sweden)

Xiangcheng Li

2016-01-01

Full Text Available Two kinds of hexagonal aluminum honeycombs are tested to study their out-of-plane crushing behavior. In the tests, honeycomb samples, including single hexagonal aluminum honeycomb (SHAH samples and two stack-up combined hexagonal aluminum honeycombs (CHAH samples, are compressed at a fixed quasistatic loading rate. The results show that the inserting process of CHAH can erase the initial peak stress that occurred in SHAH. Meanwhile, energy-absorbing property of combined honeycomb samples is more beneficial than the one of single honeycomb sample with the same thickness if the two types of honeycomb samples are completely crushed. Then, the applicability of the existing theoretical model for single hexagonal honeycomb is discussed, and an area equivalent method is proposed to calculate the crushing stress for nearly regular hexagonal honeycombs. Furthermore, a semiempirical formula is proposed to calculate the inserting plateau stress of two stack-up CHAH, in which structural parameters and mechanics properties of base material are concerned. The results show that the predicted stresses of three kinds of two stack-up combined honeycombs are in good agreement with the experimental data. Based on this study, stress-displacement curve of aluminum honeycombs can be designed in detail, which is very beneficial to optimize the energy-absorbing structures in engineering fields.

Stresses, fatigue and fracture analysis in the tube sheets

International Nuclear Information System (INIS)

Billon, F.

1986-05-01

The purpose of the present work is to study the behaviour of the nuclear PWR steam generator tube sheet. But the methods developed in this field can easily be generalized in order to study tube sheets from any other type of heat exchangers. The aim of the stress analysis of these sheets is to verify their correct design, to quantify the risk of fatigue damage in the areas submitted to a high stress concentration and through the fracture mechanic, to make sure there is no risk of fast fracture resulting from initiated or pre-existing defects. This analysis necessarily relates to the calculation of stresses in all parts of the multidrilled area, mainly around the holes where they are concentrated. However the tube sheets are so complexe structures that their direct modelization cannot be envisaged within the context of the finite element method. We then must refer to the concept of equivalent medium in order to calculate the nominal stresses. Then using the stresses multiple fonctions appropriate to the net geometry, we can calculate the actual stresses concentrated around the holes. The method depends on the behaviour of the elementary volume which represents the behaviour of the multidrilled medium. This approach must allow to correctly take account of the ''thermal skin effect'', which is a phenomenon particular to the tube sheets with thermal loads. It must as well be generalized in order to analyse the irregular ligaments which affect the periodical stresses distribution and locally overconcentrate them [fr

Comparative transcriptome analysis of the Asteraceae halophyte Karelinia caspica under salt stress.

Science.gov (United States)

Zhang, Xia; Liao, Maoseng; Chang, Dan; Zhang, Fuchun

2014-12-17

Much attention has been given to the potential of halophytes as sources of tolerance traits for introduction into cereals. However, a great deal remains unknown about the diverse mechanisms employed by halophytes to cope with salinity. To characterize salt tolerance mechanisms underlying Karelinia caspica, an Asteraceae halophyte, we performed Large-scale transcriptomic analysis using a high-throughput Illumina sequencing platform. Comparative gene expression analysis was performed to correlate the effects of salt stress and ABA regulation at the molecular level. Total sequence reads generated by pyrosequencing were assembled into 287,185 non-redundant transcripts with an average length of 652 bp. Using the BLAST function in the Swiss-Prot, NCBI nr, GO, KEGG, and KOG databases, a total of 216,416 coding sequences associated with known proteins were annotated. Among these, 35,533 unigenes were classified into 69 gene ontology categories, and 18,378 unigenes were classified into 202 known pathways. Based on the fold changes observed when comparing the salt stress and control samples, 60,127 unigenes were differentially expressed, with 38,122 and 22,005 up- and down-regulated, respectively. Several of the differentially expressed genes are known to be involved in the signaling pathway of the plant hormone ABA, including ABA metabolism, transport, and sensing as well as the ABA signaling cascade. Transcriptome profiling of K. caspica contribute to a comprehensive understanding of K. caspica at the molecular level. Moreover, the global survey of differentially expressed genes in this species under salt stress and analyses of the effects of salt stress and ABA regulation will contribute to the identification and characterization of genes and molecular mechanisms underlying salt stress responses in Asteraceae plants.

Analysis of DNA methylation of maize in response to osmotic and salt stress based on methylation-sensitive amplified polymorphism.

Science.gov (United States)

Tan, Ming-pu

2010-01-01

Water stress is known to alter cytosine methylation, which generally represses transcription. However, little is known about the role of methylation alteration in maize under osmotic stress. Here, methylation-sensitive amplified polymorphism (MSAP) was used to screen PEG- or NaCl-induced methylation alteration in maize seedlings. The sequences of 25 differentially amplified fragments relevant to stress were successfully obtained. Two stress-specific fragments from leaves, LP166 and LPS911, shown to be homologous to retrotransposon Gag-Pol protein genes, suggested that osmotic stress-induced methylation of retrotransposons. Three MSAP fragments, representing drought-induced or salt-induced methylation in leaves, were homologous to a maize aluminum-induced transporter. Besides these, heat shock protein HSP82, Poly [ADP-ribose] polymerase 2, Lipoxygenase, casein kinase (CK2), and dehydration-responsive element-binding (DREB) factor were also homologs of MSAP sequences from salt-treated roots. One MSAP fragment amplified from salt-treated roots, designated RS39, was homologous to the first intron of maize protein phosphatase 2C (zmPP2C), whereas - LS103, absent from salt-treated leaves, was homologous to maize glutathione S-transferases (zmGST). Expression analysis showed that salt-induced intron methylation of root zmPP2C significantly downregulated its expression, while salt-induced demethylation of leaf zmGST weakly upregulated its expression. The results suggested that salinity-induced methylation downregulated zmPP2C expression, a negative regulator of the stress response, while salinity-induced demethylation upregulated zmGST expression, a positive effecter of the stress response. Altered methylation, in response to stress, might also be involved in stress acclimation. Copyright 2009 Elsevier Masson SAS. All rights reserved.

Stress intensity evaluation for surface crack with use of boundary element method and influence function method and the surface crack extension analysis

International Nuclear Information System (INIS)

Yuuki, R.; Ejima, K.

1991-01-01

In this study, three-dimensional boundary element elastostatic analysis is carried out on various surface crack problems. The present BEM uses a Mindlin's solution as well as a Kelvin's solution as a fundamental solution. So we can obtain accurate solutions for a surface crack just before or after a penetration. The obtained solutions for various shapes of surface cracks are stored as the data base, based on the influence function method. We develop the surface crack extension analysis system using the stress intensity factor data base and also the fatigue crack growth law. Our system seems to be useful especially for the analysis of the surface crack just before or after the penetration and also under the residual stresses

Preliminary thermal and stress analysis of the SINQ window

International Nuclear Information System (INIS)

Heidenreich, G.

1991-01-01

Preliminary results of a finite element analysis for the SINQ proton beam window are presented. Temperatures and stresses are calculated in an axisymmetric model. As a result of these calculations, the H 2 O-cooled window (safety window) could be redesigned in such a way that plastic deformation resulting from excessive stress in some areas is avoided. (author)

Prediction of residual stress distributions due to surface machining and welding and crack growth simulation under residual stress distribution

International Nuclear Information System (INIS)

Ihara, Ryohei; Katsuyama, JInya; Onizawa, Kunio; Hashimoto, Tadafumi; Mikami, Yoshiki; Mochizuki, Masahito

2011-01-01

Research highlights: → Residual stress distributions due to welding and machining are evaluated by XRD and FEM. → Residual stress due to machining shows higher tensile stress than welding near the surface. → Crack growth analysis is performed using calculated residual stress. → Crack growth result is affected machining rather than welding. → Machining is an important factor for crack growth. - Abstract: In nuclear power plants, stress corrosion cracking (SCC) has been observed near the weld zone of the core shroud and primary loop recirculation (PLR) pipes made of low-carbon austenitic stainless steel Type 316L. The joining process of pipes usually includes surface machining and welding. Both processes induce residual stresses, and residual stresses are thus important factors in the occurrence and propagation of SCC. In this study, the finite element method (FEM) was used to estimate residual stress distributions generated by butt welding and surface machining. The thermoelastic-plastic analysis was performed for the welding simulation, and the thermo-mechanical coupled analysis based on the Johnson-Cook material model was performed for the surface machining simulation. In addition, a crack growth analysis based on the stress intensity factor (SIF) calculation was performed using the calculated residual stress distributions that are generated by welding and surface machining. The surface machining analysis showed that tensile residual stress due to surface machining only exists approximately 0.2 mm from the machined surface, and the surface residual stress increases with cutting speed. The crack growth analysis showed that the crack depth is affected by both surface machining and welding, and the crack length is more affected by surface machining than by welding.

Numerical analysis of residual stresses reconstruction for axisymmetric glass components

Science.gov (United States)

Tao, Bo; Xu, Shuang; Yao, Honghui

2018-01-01

A non-destructive measurement method for 3D stress state in a glass cylinder using photoelasticity has been analyzed by simulation in this research. Based on simulated stresses in a glass cylinder, intensity of the cylinder in a circular polariscope can be calculated by Jones calculus. Therefore, the isoclinic angle and optical retardation can be obtained by six steps phase shifting technique. Through the isoclinic angle and optical retardation, the magnitude and distribution of residual stresses inside the glass cylinder in cylindrical coordinate system can be reconstructed. Comparing the reconstructed stresses with numerical simulated stresses, the results verify this non-destructive method can be used to reconstruct the 3D stresses. However, there are some mismatches in axial stress, radial stress and circumferential stress.

Stress Analysis

DEFF Research Database (Denmark)

Burcharth, Hans F.

The following types of forces contribute to the stresses in a Dolos in a pack exposed to waves: 1)Gravity forces Compaction forces (mainly due to settlements, gravity and flow forces) 2) Flow forces 3) Impact forces (impacts between moving concrete blocks)......The following types of forces contribute to the stresses in a Dolos in a pack exposed to waves: 1)Gravity forces Compaction forces (mainly due to settlements, gravity and flow forces) 2) Flow forces 3) Impact forces (impacts between moving concrete blocks)...

Finite element type of stress analysis for parts based on S235 JR steel welding

Directory of Open Access Journals (Sweden)

C. Babis

2014-04-01

Full Text Available The determination of static and/or variable stress, in case of complex shaped welded structures is hard to achieve. One solution, though, is the use of finite element method, implemented by means of various specialized software. Nowadays, this method has become very popular due to its high precision of data obtained through both research and finite element analysis. Hence, the present paper deals with the modelling of the pull-out behaviour of concave and convex welded joints through finite element method.

Transcriptome analysis uncovers Arabidopsis F-BOX STRESS INDUCED 1 as a regulator of jasmonic acid and abscisic acid stress gene expression.

Science.gov (United States)

Gonzalez, Lauren E; Keller, Kristen; Chan, Karen X; Gessel, Megan M; Thines, Bryan C

2017-07-17

The ubiquitin 26S proteasome system (UPS) selectively degrades cellular proteins, which results in physiological changes to eukaryotic cells. F-box proteins are substrate adaptors within the UPS and are responsible for the diversity of potential protein targets. Plant genomes are enriched in F-box genes, but the vast majority of these have unknown roles. This work investigated the Arabidopsis F-box gene F-BOX STRESS INDUCED 1 (FBS1) for its effects on gene expression in order elucidate its previously unknown biological function. Using publically available Affymetrix ATH1 microarray data, we show that FBS1 is significantly co-expressed in abiotic stresses with other well-characterized stress response genes, including important stress-related transcriptional regulators. This gene suite is most highly expressed in roots under cold and salt stresses. Transcriptome analysis of fbs1-1 knock-out plants grown at a chilling temperature shows that hundreds of genes require FBS1 for appropriate expression, and that these genes are enriched in those having roles in both abiotic and biotic stress responses. Based on both this genome-wide expression data set and quantitative real-time PCR (qPCR) analysis, it is apparent that FBS1 is required for elevated expression of many jasmonic acid (JA) genes that have established roles in combatting environmental stresses, and that it also controls a subset of JA biosynthesis genes. FBS1 also significantly impacts abscisic acid (ABA) regulated genes, but this interaction is more complex, as FBS1 has both positive and negative effects on ABA-inducible and ABA-repressible gene modules. One noteworthy effect of FBS1 on ABA-related stress processes, however, is the restraint it imposes on the expression of multiple class I LIPID TRANSFER PROTEIN (LTP) gene family members that have demonstrated protective effects in water deficit-related stresses. FBS1 impacts plant stress responses by regulating hundreds of genes that respond to the plant

Cardiovascular response to acute stress in freely moving rats: time-frequency analysis.

Science.gov (United States)

Loncar-Turukalo, Tatjana; Bajic, Dragana; Japundzic-Zigon, Nina

2008-01-01

Spectral analysis of cardiovascular series is an important tool for assessing the features of the autonomic control of the cardiovascular system. In this experiment Wistar rats ecquiped with intraarterial catheter for blood pressure (BP) recording were exposed to stress induced by blowing air. The problem of non stationary data was overcomed applying the Smoothed Pseudo Wigner Villle (SPWV) time-frequency distribution. Spectral analysis was done before stress, during stress, immediately after stress and later in recovery. The spectral indices were calculated for both systolic blood pressure (SBP) and pulse interval (PI) series. The time evolution of spectral indices showed perturbed sympathovagal balance.

Patients' experiences in a guided Internet- and App-based stress intervention for college students: A qualitative study

Directory of Open Access Journals (Sweden)

R.J. Fleischmann

2018-06-01

Full Text Available Introduction: Academic education is often associated with increased stress and adverse effects on mental health. Internet-based interventions have shown to be effective in reducing stress-related symptoms. However, college students as target group so far have not been reached appropriately with psychological interventions and little is known about college students' perception of Internet-based stress management interventions. The objective of this study was to explore the experiences of students participating in an Internet- and App-based stress management intervention originally developed for stressed employees and subsequently adapted and tailored to college students. Method: Semi-structured interviews were conducted with ten participants selected from a randomized controlled trial that evaluated the effectiveness of an Internet- and App-based stress training. The selection of participants aimed to include students with different levels of treatment success. In order to enable an in-depth examination of intervention elements causing dissatisfaction, the interviews were systematically adapted regarding participants' statements in a precedent questionnaire. The interview material was analyzed based on the grounded theory method and thematic analysis. Results: Results suggest students perceive a necessity to adapt Internet-based interventions to their particular needs. Students' statements indicate that a scientific perspective on the intervention and instable life circumstances could be student-specific factors affecting treatment experience. General themes emerging from the data were attitudes towards individualization and authenticity as well as demands towards different functions of feedback. Discussion: Participants' experiences hint at certain intellectual and lifestyle-related characteristics of this population. Future studies should explore whether adaptions to these characteristics lead to a higher acceptance, adherence and effectiveness

Stress analysis of pressure vessels in nuclear power plants: pt.2

International Nuclear Information System (INIS)

Kim, C.W.; Chu, Y.W.

1976-01-01

Stress analysis of tapered cylinder of reactor vessels in investigated by means of the intersection method. The tapered cylinder is approximated into three models average cylinder, conical frustum, and ring. The results are compared with those of the finite element method program and an experiment. In this paper, the following results are obtained: (1) the best approximation has been obtained by the ring model analysis: (2) the intersection analysis of the tapered cylinder by the ring model shows a sufficient accuracy for the stress analysis of reactor vessels. (author)

Reliability analysis and optimisation of subsea compression system facing operational covariate stresses

International Nuclear Information System (INIS)

Okaro, Ikenna Anthony; Tao, Longbin

2016-01-01

This paper proposes an enhanced Weibull-Corrosion Covariate model for reliability assessment of a system facing operational stresses. The newly developed model is applied to a Subsea Gas Compression System planned for offshore West Africa to predict its reliability index. System technical failure was modelled by developing a Weibull failure model incorporating a physically tested corrosion profile as stress in order to quantify the survival rate of the system under additional operational covariates including marine pH, temperature and pressure. Using Reliability Block Diagrams and enhanced Fusell-Vesely formulations, the whole system was systematically decomposed to sub-systems to analyse the criticality of each component and optimise them. Human reliability was addressed using an enhanced barrier weighting method. A rapid degradation curve is obtained on a subsea system relative to the base case subjected to a time-dependent corrosion stress factor. It reveals that subsea system components failed faster than their Mean time to failure specifications from Offshore Reliability Database as a result of cumulative marine stresses exertion. The case study demonstrated that the reliability of a subsea system can be systematically optimised by modelling the system under higher technical and organisational stresses, prioritising the critical sub-systems and making befitting provisions for redundancy and tolerances. - Highlights: • Novel Weibull Corrosion-Covariate model for reliability analysis of subsea assets. • Predict the accelerated degradation profile of a subsea gas compression. • An enhanced optimisation method based on Fusell-Vesely decomposition process. • New optimisation approach for smoothening of over- and under-designed components. • Demonstrated a significant improvement in producing more realistic failure rate.

Stress-strain state analysis and optimization of rod system under periodic pulse load

Directory of Open Access Journals (Sweden)

Grebenyuk Grigory

2018-01-01

Full Text Available The paper considers the problem of analysis and optimization of rod systems subjected to combined static and periodic pulse load. As a result of the study the analysis method was developed based on traditional approach to solving homogeneous matrix equations of state and a special algorithm for developing a particular solution. The influence of pulse parameters variations on stress-strain state of a rod system was analyzed. Algorithms for rod systems optimization were developed basing on strength recalculation and statement and solution of optimization problem as a problem of nonlinear mathematical programming. Recommendations are developed for efficient organization of process for optimization of rod systems under static and periodic pulse load.

CANDIDATE GENE ANALYSIS IN ISRAELI SOLDIERS WITH STRESS FRACTURES

Directory of Open Access Journals (Sweden)

Ran Yanovich

2012-03-01

Full Text Available To investigate the association of polymorphisms within candidate genes which we hypothesized may contribute to stress fracture predisposition, a case-control, cross- sectional study design was employed. Genotyping 268 Single Nucleotide Polymorphisms- SNPs within 17 genes in 385 Israeli young male and female recruits (182 with and 203 without stress fractures. Twenty-five polymorphisms within 9 genes (NR3C1, ANKH, VDR, ROR2, CALCR, IL6, COL1A2, CBG, and LRP4 showed statistically significant differences (p < 0.05 in the distribution between stress fracture cases and non stress fracture controls. Seventeen genetic variants were associated with an increased stress fracture risk, and eight variants with a decreased stress fracture risk. None of the SNP associations remained significant after correcting for multiple comparisons (false discovery rate- FDR. Our findings suggest that genes may be involved in stress fracture pathogenesis. Specifically, the CALCR and the VDR genes are intriguing candidates. The putative involvement of these genes in stress fracture predisposition requires analysis of more cases and controls and sequencing the relevant genomic regions, in order to define the specific gene mutations

Interlaminar stress analysis for carbon/epoxy composite space rotors

Directory of Open Access Journals (Sweden)

C Lian

2016-09-01

Full Text Available This paper extends the previous works that appears in the International Journal of Multiphysics, Varatharajoo, Salit and Goh (2010. An approach incorporating cohesive zone modelling technique is incorporated into an optimized flywheel to properly simulate the stresses at the layer interfaces. Investigation on several fiber stacking sequences are also conducted to demonstrate the effect of fiber orientations on the overall rotor stress as well as the interface stress behaviour. The results demonstrated that the rotor interlaminar stresses are within the rotor materials' ultimate strength and that the fiber direction with a combination of 45°/-45°/0° offers the best triple layer rotor among the few combinations selected for this analysis. It was shown that the present approach can facilitate also further investigation on the interface stress behaviour of rotating rotors.

Stress corrosion crack tip microstructure in nickel-based alloys

International Nuclear Information System (INIS)

Shei, S.A.; Yang, W.J.

1994-04-01

Stress corrosion cracking behavior of several nickel-base alloys in high temperature caustic environments has been evaluated. The crack tip and fracture surfaces were examined using Auger/ESCA and Analytical Electron Microscopy (AEM) to determine the near crack tip microstructure and microchemistry. Results showed formation of chromium-rich oxides at or near the crack tip and nickel-rich de-alloying layers away from the crack tip. The stress corrosion resistance of different nickel-base alloys in caustic may be explained by the preferential oxidation and dissolution of different alloying elements at the crack tip. Alloy 600 (UNS N06600) shows good general corrosion and intergranular attack resistance in caustic because of its high nickel content. Thermally treated Alloy 690 (UNS N06690) and Alloy 600 provide good stress corrosion cracking resistance because of high chromium contents along grain boundaries. Alloy 625 (UNS N06625) does not show as good stress corrosion cracking resistance as Alloy 690 or Alloy 600 because of its high molybdenum content

Analysis of Biaxially Stressed Bridge Deck Plates

DEFF Research Database (Denmark)

Jönsson, Jeppe; Bondum, Tommi Højer

2012-01-01

The ultimate state analysis of bridge deck plates at the intersection zone between main girders and transverse beams is complicated by biaxial membrane stresses, which may be in compression or tension in either direction depending on the bridge configuration and the specific location. This paper...

Tensorial analysis of Eshelby stresses in 3D supercooled liquids

Science.gov (United States)

Lemaître, Anaël

2015-10-01

It was recently proposed that the local rearrangements governing relaxation in supercooled liquids impress on the liquid medium long-ranged (Eshelby) stress fluctuations that accumulate over time. From this viewpoint, events must be characterized by elastic dipoles, which are second order tensors, and Eshelby fields are expected to show up in stress and stress increment correlations, which are fourth order tensor fields. We construct here an analytical framework that permits analyzing such tensorial correlations in isotropic media in view of accessing Eshelby fields. Two spherical bases are introduced, which correspond to Cartesian and spherical coordinates for tensors. We show how they can be used to decompose stress correlations and thus test such properties as isotropy and power-law scalings. Eshelby fields and the predicted stress correlations in an infinite medium are shown to belong to an algebra that can conveniently be described using the spherical tensor bases. Using this formalism, we demonstrate that the inherent stress field of 3D supercooled liquids is power law correlated and carries the signature of Eshelby fields, thus supporting the idea that relaxation events give rise to Eshelby stresses that accumulate over time.

Finite element analysis of residual stress in plasma-sprayed ceramic

International Nuclear Information System (INIS)

Mullen, R.L.; Hendricks, R.C.; McDonald, G.

1985-01-01

Residual stress in a ZrO 2 -Y 2 O 3 ceramic coating resulting from the plasma spraying operation is calculated. The calculations were done using the finite element method. Both thermal and mechanical analysis were performed. The resulting residual stress field was compared to the measurements obtained by Hendricks and McDonald. Reasonable agreement between the predicted and measured moment occurred. However, the resulting stress field is not in pure bending

Stress Analysis of Single Spacer Grid Support considering Fuel Rod

Energy Technology Data Exchange (ETDEWEB)

Yoo, Y. G.; Jung, D. H.; Kim, J. H. [Chungnam National University, Daejeon (Korea, Republic of); Park, J. K.; Jeon, K. L. [Korea Nuclear Fuel, Daejeon (Korea, Republic of)

2010-10-15

Pressurized water reactor (PWR) nuclear fuel assembly is mainly composed of a top-end piece, a bottom-end piece, lots of fuel rods, and several spacer grids. Among them, the main function of spacer grid is protecting fuel rods from Fluid Induced Vibration (FIV). The cross section of spacer grid assembled by laser welding in upper and lower point. When the fuel rod inserted in spacer gird, spring and dimple and around of welded area got a stresses. The main hypothesis of this analysis is the boundary area of HAZ and base metal can get a lot of damage than other area by FIV. So, design factors of spacer grid mainly considered to preventing the fatigue failure in HAZ and spring and dimple of spacer grid. From previous researching, the environment in reactor verified. Pressure and temperature of light water observed 15MPa and 320 .deg. C, and vibration of the fuel rod observed within 0 {approx} 50Hz. In this study, mechanical properties of zirconium alloy that extracted from the test and the spacer grid model which used in the PWR were applied in stress analyzing. General-purpose finite element analysis program was used ANSYS Workbench 12.0.1 version. 3-D CAD program CATIA was used to create spacer grid model

Transcriptome-Based Analysis of Dof Family Transcription Factors and Their Responses to Abiotic Stress in Tea Plant (Camellia sinensis

Directory of Open Access Journals (Sweden)

Hui Li

2016-01-01

Full Text Available Tea plant (Camellia sinensis (L. O. Kuntze is affected by abiotic stress during its growth and development. DNA-binding with one finger (Dof transcription factors (TFs play important roles in abiotic stress tolerance of plants. In this study, a total of 29 putative Dof TFs were identified based on transcriptome of tea plant, and the conserved domains and common motifs of these CsDof TFs were predicted and analyzed. The 29 CsDof proteins were divided into 7 groups (A, B1, B2, C1, C2.1, C2.2, and D2, and the interaction networks of Dof proteins in C. sinensis were established according to the data in Arabidopsis. Gene expression was analyzed in “Yingshuang” and “Huangjinya” under four experimental stresses by qRT-PCR. CsDof genes were expressed differentially and related to different abiotic stress conditions. In total, our results might suggest that there is a potential relationship between CsDof factors and tea plant stress resistance.

Depression and oxidative stress: results from a meta-analysis of observational studies.

Science.gov (United States)

Palta, Priya; Samuel, Laura J; Miller, Edgar R; Szanton, Sarah L

2014-01-01

To perform a systematic review and meta-analysis that quantitatively tests and summarizes the hypothesis that depression results in elevated oxidative stress and lower antioxidant levels. We performed a meta-analysis of studies that reported an association between depression and oxidative stress and/or antioxidant status markers. PubMed and EMBASE databases were searched for articles published from January 1980 through December 2012. A random-effects model, weighted by inverse variance, was performed to pool standard deviation (Cohen's d) effect size estimates across studies for oxidative stress and antioxidant status measures, separately. Twenty-three studies with 4980 participants were included in the meta-analysis. Depression was most commonly measured using the Diagnostic and Statistical Manual of Mental Disorders, Fourth Edition criteria. A Cohen's d effect size of 0.55 (95% confidence interval = 0.47-0.63) was found for the association between depression and oxidative stress, indicating a roughly 0.55 of 1-standard-deviation increase in oxidative stress among individuals with depression compared with those without depression. The results of the studies displayed significant heterogeneity (I(2) = 80.0%, p < .001). A statistically significant effect was also observed for the association between depression and antioxidant status markers (Cohen's d = -0.24, 95% confidence interval = -0.33 to -0.15). This meta-analysis observed an association between depression and oxidative stress and antioxidant status across many different studies. Differences in measures of depression and markers of oxidative stress and antioxidant status markers could account for the observed heterogeneity. These findings suggest that well-established associations between depression and poor heath outcomes may be mediated by high oxidative stress.

Two-dimensional imaging of Debye-Scherrer ring for tri-axial stress analysis of industrial materials

International Nuclear Information System (INIS)

Sasaki, T; Maruyama, Y; Ohba, H; Ejiri, S

2014-01-01

In this study, an application of the two-dimensional imaging technology to the X ray tri-axial stress analysis was studied. An image plate (IP) was used to obtain a Debye-Scherre ring and the image data was analized for determining stress. A new principle for stress analysis which is suitable to two-dimensional imaging data was used. For the verification of this two-dimensional imaging type X-ray stress measurement method, an experiment was conducted using a ferritic steel sample which was processed with a surface grinder. Tri-axial stress analysis was conducted to evaluate the sample. The conventional method for X-ray tri-axial stress analysis proposed by Dölle and Hauk was used to evaluate residual stress in order to compare with the present method. As a result, it was confirmed that a sufficiently highly precise and high-speed stress measurement was enabled with the two-dimensional imaging technology compared with the conventional method

Parametric analysis of stress in the ICF HYLIFE converter structure

International Nuclear Information System (INIS)

Hovingh, J.; Blink, J.A.

1980-10-01

The concept of a liquid-metal first wall in an ICF energy converter has a particularly attractive feature: the liquid metal absorbs the short-ranged fusion energy and moderates and attenuates the neutron energy so that the converter structure may have a lifetime similar to that of a conventional power plant. However, the sudden deposition of fusion energy in the liquid-metal first wall will result in disassembly of the liquid, which then impacts on the structure. The impact pressure on the structure is a strong function of the location and thickness of the liquid-metal first wall. The impact stress is determined by the impact pressure and duration and by the thickness and location of the structure. The maximum allowable stress is determined by the design stress criteria chosen by the structural designer. Scaling laws for the impact pressure as a function of the liquid-metal first wall location and mass are presented for a 2700 MW(f) (fusion power) plant with either one or four fusion reactor vessels. A methodology for determining the optimum combination of liquid-metal first wall geometry and first-structural-wall thickness is shown. Based on the methodology developed, a parametric analysis is presented of the liquid-metal flow rate and first-structural-wall requirements

Non-linear elastic thermal stress analysis with phase changes

International Nuclear Information System (INIS)

Amada, S.; Yang, W.H.

1978-01-01

The non-linear elastic, thermal stress analysis with temperature induced phase changes in the materials is presented. An infinite plate (or body) with a circular hole (or tunnel) is subjected to a thermal loading on its inner surface. The peak temperature around the hole reaches beyond the melting point of the material. The non-linear diffusion equation is solved numerically using the finite difference method. The material properties change rapidly at temperatures where the change of crystal structures and solid-liquid transition occur. The elastic stresses induced by the transient non-homogeneous temperature distribution are calculated. The stresses change remarkably when the phase changes occur and there are residual stresses remaining in the plate after one cycle of thermal loading. (Auth.)

FIB-based measurement of local residual stresses on microsystems

Science.gov (United States)

Vogel, Dietmar; Sabate, Neus; Gollhardt, Astrid; Keller, Juergen; Auersperg, Juergen; Michel, Bernd

2006-03-01

The paper comprises research results obtained for stress determination on micro and nanotechnology components. It meets the concern of controlling stresses introduced to sensors, MEMS and electronics devices during different micromachining processes. The method bases on deformation measurement options made available inside focused ion beam equipment. Removing locally material by ion beam milling existing stresses / residual stresses lead to deformation fields around the milled feature. Digital image correlation techniques are used to extract deformation values from micrographs captured before and after milling. In the paper, two main milling features have been analyzed - through hole and through slit milling. Analytical solutions for stress release fields of in-plane stresses have been derived and compared to respective experimental findings. Their good agreement allows to settle a method for determination of residual stress values, which is demonstrated for thin membranes manufactured by silicon micro technology. Some emphasis is made on the elimination of main error sources for stress determination, like rigid body object displacements and rotations due to drifts of experimental conditions under FIB imaging. In order to illustrate potential application areas of the method residual stress suppression by ion implantation is evaluated by the method and reported here.

Structural and stress analysis of nuclear piping systems

International Nuclear Information System (INIS)

Hata, Hiromichi

1982-01-01

The design of the strength of piping system is important in plant design, and its outline on the example of PWRs is reported. The standards and guides concerning the design of the strength of piping system are shown. The design condition for the strength of piping system is determined by considering the requirements in the normal operation of plants and for the safety design of plants, and the loads in normal operation, testing, credible accident and natural environment are explained. The methods of analysis for piping system are related to the transient phenomena of fluid, piping structure and local heat conduction, and linear static analysis, linear time response analysis, nonlinear time response analysis, thermal stress analysis and fluid transient phenomenon analysis are carried out. In the aseismatic design of piping system, it is desirable to avoid the vibration together with a building supporting it, and as a rule, to make it into rigid structure. The piping system is classified into high temperature and low temperature pipings. The formulas for calculating stress and the allowable condition, the points to which attention must be paid in the design of piping strength and the matters to be investigated hereafter are described. (Kako, I.)

Numerical analysis of interacting cracks in biaxial stress field

International Nuclear Information System (INIS)

Kovac, M.; Cizelj, L.

1999-01-01

The stress corrosion cracks as seen for example in PWR steam generator tubing made of Inconel 600 usually produce highly irregular kinked and branched crack patterns. Crack initialization and propagation depends on stress state underlying the crack pattern. Numerical analysis (such as finite element method) of interacting kinked and branched cracks can provide accurate solutions. This paper discusses the use of general-purpose finite element code ABAQUS for evaluating stress fields at crack tips of interacting complex cracks. The results obtained showed reasonable agreement with the reference solutions and confirmed use of finite elements in such class of problems.(author)

Effectiveness of Mindfulness-Based Stress Reduction (MBSR In Stress and Fatigue in Patients with Multiple Sclerosis (MS

Directory of Open Access Journals (Sweden)

Ebrahimi Alisaleh

2016-07-01

Full Text Available Multiple sclerosis (MS disease can lead to creation of mental and behavioral disorders such as stress and fatigue. Controlling the problems in patients is essential. Hence, this study has considered effectiveness of mindfulnessbased stress reduction in stress and fatigue symptoms in patients with multiple sclerosis (MS.this study is in kind of semi-experimental research in form of pretest posttest pattern with control group. Statistical population of the study consists of all patients with multiple sclerosis referred to Iran MS Association by 2016. Sampling method in this study is available sampling and based on having inclusion criteria. among patients who gained point higher than 21.8 in stress inventory and point higher than 5.1 in fatigue inventory, 30 people are selected as sample randomly and are placed in 2 groups with 15 people in each group. The experimental group was placed under mindfulnessbased stress reduction (MBSR training course including 8 sessions with 2hrs per session. k\\however, no intervention was done in control group. All patients in experimental and control groups fulfilled stress and fatigue inventories before and after intervention. obtained data was analyzed using MANCOVA and in SPSS22 software. obtained results show that there is significant difference between the two groups in terms of stress and fatigue after intervention (p<0.001.according to obtained results, it could be found that treatment method of mindfulness-based stress reduction can help reduction of symptoms of stress and fatigue in patients with MS.

Analysis of the stress raising action of flaws in laser clad deposits

International Nuclear Information System (INIS)

Alam, M.M.; Kaplan, A.F.H.; Tuominen, J.; Vuoristo, P.; Miettinen, J.; Poutala, J.; Näkki, J.; Junkala, J.; Peltola, T.; Barsoum, Z.

2013-01-01

Highlights: ► Laser clad defects are 0D-pores/inclusions, 1D-clad waviness or 2D-planar defects. ► Surface pore of laser clad bar initiates fatigue cracks. ► Side edge surface pores are more critical than in-clad surface pores. ► Smaller notch radius and angle of as-laser clad surface raises stress significantly. ► Planar inner defects grow faster towards surface. - Abstract: Fatigue cracking of laser clad cylindrical and square section bars depends upon a variety of factors. This paper presents Finite Element Analysis (FEA) of the different macro stress fields generated as well as stress raisers created by laser cladding defects for four different fatigue load conditions. As important as the defect types are their locations and orientations, categorized into zero-, one- and two-dimensional defects. Pores and inclusions become critical close to surfaces. The performance of as-clad surfaces can be governed by the sharpness of surface notches and planar defects like hot cracks or lack-of-fusion (LOF) are most critical if oriented vertically, transverse to the bar axis. The combination of the macro stress field with the defect type and its position and orientation determines whether it is the most critical stress raiser. Based on calculated cases, quantitative and qualitative charts were developed as guidelines to visualize the trends of different combinations

Meditation for posttraumatic stress: Systematic review and meta-analysis.

Science.gov (United States)

Hilton, Lara; Maher, Alicia Ruelaz; Colaiaco, Benjamin; Apaydin, Eric; Sorbero, Melony E; Booth, Marika; Shanman, Roberta M; Hempel, Susanne

2017-07-01

We conducted a systematic review and meta-analysis that synthesized evidence from randomized controlled trials of meditation interventions to provide estimates of their efficacy and safety in treating adults diagnosed with posttraumatic stress disorder (PTSD). This review was based on an established protocol (PROSPERO: CRD42015025782) and is reported according to PRISMA guidelines. Outcomes of interest included PTSD symptoms, depression, anxiety, health-related quality of life, functional status, and adverse events. Meta-analyses were conducted using the Hartung-Knapp-Sidik-Jonkman method for random-effects models. Quality of evidence was assessed using the Grade of Recommendations Assessment, Development, and Evaluation (GRADE) approach. In total, 10 trials on meditation interventions for PTSD with 643 participants met inclusion criteria. Across interventions, adjunctive meditation interventions of mindfulness-based stress reduction, yoga, and the mantram repetition program improve PTSD and depression symptoms compared with control groups, but the findings are based on low and moderate quality of evidence. Effects were positive but not statistically significant for quality of life and anxiety, and no studies addressed functional status. The variety of meditation intervention types, the short follow-up times, and the quality of studies limited analyses. No adverse events were reported in the included studies; only half of the studies reported on safety. Meditation appears to be effective for PTSD and depression symptoms, but in order to increase confidence in findings, more high-quality studies are needed on meditation as adjunctive treatment with PTSD-diagnosed participant samples large enough to detect statistical differences in outcomes. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Residual stress analysis in linear friction welded in-service Inconel 718 superalloy via neutron diffraction and contour method approaches

Energy Technology Data Exchange (ETDEWEB)

Smith, M. [University of British Columbia – Okanagan, School of Engineering, 3333 University Way, Kelowna, Canada V1V 1V7 (Canada); Levesque, J.-B. [Institut de recherche d' Hydro-Québec (IREQ), 1800 Lionel-Boulet Blvd., Varennes, Canada J3X 1S1 (Canada); Bichler, L., E-mail: lukas.bichler@ubc.ca [University of British Columbia – Okanagan, School of Engineering, 3333 University Way, Kelowna, Canada V1V 1V7 (Canada); Sediako, D. [Canadian Nuclear Laboratories, Building 459, Station 18, Chalk River, Canada K0J 1J0 (Canada); Gholipour, J.; Wanjara, P. [National Research Council of Canada, Aerospace 5145 Decelles Ave., Montreal, Canada H3T 2B2 (Canada)

2017-04-13

In this study, an analysis of elastic residual stress in Inconel{sup ®} 718 (IN 718) linear friction welds (LFWs) was carried out. In particular, the suitability of LFW for manufacturing and repair of aero engine components was emulated by joining virgin and in-service (extracted from a turbine disk) materials. The evolution in the residual strains and stresses in the heat-affected zone (HAZ), thermomechanically affected zone (TMAZ) and dynamically recrystallized zone (DRX) of the weld was characterized using the neutron diffraction and contour methods. The results provided insight into diverse challenges in quantitative analysis of residual stresses in welded IN 718 using diffraction techniques. Specifically, judicious selection of the beam width, height and stress-free lattice spacing were seen to be crucial to minimize measurement error and increase accuracy. Further, the contour method – a destructive technique relying on capturing the stress relaxation after electrical discharge machining – was used to characterize the residual stress distribution on two-dimensional plane sections of the welds. Both techniques suggested an increasing magnitude of residual stress originating from the base metal that reached a peak at the weld interface. Both methods indicated that the peak magnitude of residual stresses were below the yield stress of IN 718.

MALDI-TOF Mass Spectrometry Enables a Comprehensive and Fast Analysis of Dynamics and Qualities of Stress Responses of Lactobacillus paracasei subsp. paracasei F19

Science.gov (United States)

Schott, Ann-Sophie; Behr, Jürgen; Quinn, Jennifer; Vogel, Rudi F.

2016-01-01

Lactic acid bacteria (LAB) are widely used as starter cultures in the manufacture of foods. Upon preparation, these cultures undergo various stresses resulting in losses of survival and fitness. In order to find conditions for the subsequent identification of proteomic biomarkers and their exploitation for preconditioning of strains, we subjected Lactobacillus (Lb.) paracasei subsp. paracasei TMW 1.1434 (F19) to different stress qualities (osmotic stress, oxidative stress, temperature stress, pH stress and starvation stress). We analysed the dynamics of its stress responses based on the expression of stress proteins using MALDI-TOF mass spectrometry (MS), which has so far been used for species identification. Exploiting the methodology of accumulating protein expression profiles by MALDI-TOF MS followed by the statistical evaluation with cluster analysis and discriminant analysis of principle components (DAPC), it was possible to monitor the expression of low molecular weight stress proteins, identify a specific time point when the expression of stress proteins reached its maximum, and statistically differentiate types of adaptive responses into groups. Above the specific result for F19 and its stress response, these results demonstrate the discriminatory power of MALDI-TOF MS to characterize even dynamics of stress responses of bacteria and enable a knowledge-based focus on the laborious identification of biomarkers and stress proteins. To our knowledge, the implementation of MALDI-TOF MS protein profiling for the fast and comprehensive analysis of various stress responses is new to the field of bacterial stress responses. Consequently, we generally propose MALDI-TOF MS as an easy and quick method to characterize responses of microbes to different environmental conditions, to focus efforts of more elaborate approaches on time points and dynamics of stress responses. PMID:27783652

MALDI-TOF Mass Spectrometry Enables a Comprehensive and Fast Analysis of Dynamics and Qualities of Stress Responses of Lactobacillus paracasei subsp. paracasei F19.

Directory of Open Access Journals (Sweden)

Ann-Sophie Schott

Full Text Available Lactic acid bacteria (LAB are widely used as starter cultures in the manufacture of foods. Upon preparation, these cultures undergo various stresses resulting in losses of survival and fitness. In order to find conditions for the subsequent identification of proteomic biomarkers and their exploitation for preconditioning of strains, we subjected Lactobacillus (Lb. paracasei subsp. paracasei TMW 1.1434 (F19 to different stress qualities (osmotic stress, oxidative stress, temperature stress, pH stress and starvation stress. We analysed the dynamics of its stress responses based on the expression of stress proteins using MALDI-TOF mass spectrometry (MS, which has so far been used for species identification. Exploiting the methodology of accumulating protein expression profiles by MALDI-TOF MS followed by the statistical evaluation with cluster analysis and discriminant analysis of principle components (DAPC, it was possible to monitor the expression of low molecular weight stress proteins, identify a specific time point when the expression of stress proteins reached its maximum, and statistically differentiate types of adaptive responses into groups. Above the specific result for F19 and its stress response, these results demonstrate the discriminatory power of MALDI-TOF MS to characterize even dynamics of stress responses of bacteria and enable a knowledge-based focus on the laborious identification of biomarkers and stress proteins. To our knowledge, the implementation of MALDI-TOF MS protein profiling for the fast and comprehensive analysis of various stress responses is new to the field of bacterial stress responses. Consequently, we generally propose MALDI-TOF MS as an easy and quick method to characterize responses of microbes to different environmental conditions, to focus efforts of more elaborate approaches on time points and dynamics of stress responses.

Design and analysis of a toroidal tester for the measurement of core losses under axial compressive stress

Energy Technology Data Exchange (ETDEWEB)

Alatawneh, Natheer, E-mail: natheer80@yahoo.com [Department of Mining and Materials Engineering, McGill University, QC H3A 0G4 (Canada); Rahman, Tanvir; Lowther, David A. [Department of Electrical and Computer Engineering, McGill University, QC H3A 0E9 (Canada); Chromik, Richard [Department of Mining and Materials Engineering, McGill University, QC H3A 0G4 (Canada)

2017-06-15

Highlights: • Develop a toroidal tester for magnetic measurements under compressive axial stress. • The shape of the toroidal ring has been verified using 3D stress analysis. • The developed design has been prototyped, and measurements were carried out. • Physical explanations for the core loss trend due to stress are provided. - Abstract: Electric machine cores are subjected to mechanical stresses due to manufacturing processes. These stresses include radial, circumferential and axial components that may have significant influences on the magnetic properties of the electrical steel and hence, on the output and efficiencies of electrical machines. Previously, most studies of iron losses due to mechanical stress have considered only radial and circumferential components. In this work, an improved toroidal tester has been designed and developed to measure the core losses and the magnetic properties of electrical steel under a compressive axial stress. The shape of the toroidal ring has been verified using 3D stress analysis. Also, 3D electromagnetic simulations show a uniform flux density distribution in the specimen with a variation of 0.03 T and a maximum average induction level of 1.5 T. The developed design has been prototyped, and measurements were carried out using a steel sample of grade 35WW300. Measurements show that applying small mechanical stresses normal to the sample thickness rises the delivered core losses, then the losses decrease continuously as the stress increases. However, the drop in core losses at high stresses does not go lower than the free-stress condition. Physical explanations for the observed trend of core losses as a function of stress are provided based on core loss separation to the hysteresis and eddy current loss components. The experimental results show that the effect of axial compressive stress on magnetic properties of electrical steel at high level of inductions becomes less pronounced.

Relative Quantitative Proteomic Analysis of Brucella abortus Reveals Metabolic Adaptation to Multiple Environmental Stresses.

Science.gov (United States)

Zai, Xiaodong; Yang, Qiaoling; Yin, Ying; Li, Ruihua; Qian, Mengying; Zhao, Taoran; Li, Yaohui; Zhang, Jun; Fu, Ling; Xu, Junjie; Chen, Wei

2017-01-01

Brucella spp. are facultative intracellular pathogens that cause chronic brucellosis in humans and animals. The virulence of Brucella primarily depends on its successful survival and replication in host cells. During invasion of the host tissue, Brucella is simultaneously subjected to a variety of harsh conditions, including nutrient limitation, low pH, antimicrobial defenses, and extreme levels of reactive oxygen species (ROS) via the host immune response. This suggests that Brucella may be able to regulate its metabolic adaptation in response to the distinct stresses encountered during its intracellular infection of the host. An investigation into the differential proteome expression patterns of Brucella grown under the relevant stress conditions may contribute toward a better understanding of its pathogenesis and adaptive response. Here, we utilized a mass spectrometry-based label-free relative quantitative proteomics approach to investigate and compare global proteomic changes in B. abortus in response to eight different stress treatments. The 3 h short-term in vitro single-stress and multi-stress conditions mimicked the in vivo conditions of B. abortus under intracellular infection, with survival rates ranging from 3.17 to 73.17%. The proteomic analysis identified and quantified a total of 2,272 proteins and 74% of the theoretical proteome, thereby providing wide coverage of the B. abortus proteome. By including eight distinct growth conditions and comparing these with a control condition, we identified a total of 1,221 differentially expressed proteins (DEPs) that were significantly changed under the stress treatments. Pathway analysis revealed that most of the proteins were involved in oxidative phosphorylation, ABC transporters, two-component systems, biosynthesis of secondary metabolites, the citrate cycle, thiamine metabolism, and nitrogen metabolism; constituting major response mechanisms toward the reconstruction of cellular homeostasis and metabolic

Experiments and analysis of thermal stresses around the nozzle of the reactor vessel

International Nuclear Information System (INIS)

Song, D.H.; Oh, J.H.; Song, H.K.; Park, D.S.; Shon, K.H.

1981-01-01

This report describes the results of analysis and experiments on the thermal stress around the reactor vessel nozzle performed to establish a capability of thermal stress analysis of pressure vessel subjected to thermal loadings. Firstly, heat conduction analysis during reactor design transients and analysis on the experimental model were performed using computer code FETEM-1 for the purpose of verification of FETEM-1 which was developed in 1979 and will be used to obtain the temperature distribution in a solid body under the steady-state and the transient conditions. The results of the analysis was compared to the results in the Stress Report of Kori-1 reactor vessel and those from experiments on the model, respectively

Evaluation on double-wall-tube residual stress distribution of sodium-heated steam generator by neutron diffraction and numerical analysis

International Nuclear Information System (INIS)

Kisohara, N.; Suzuki, H.; Akita, K.; Kasahara, N.

2012-01-01

A double-wall-tube is nominated for the steam generator heat transfer tube of future sodium fast reactors (SFRs) in Japan, to decrease the possibility of sodium/water reaction. The double-wall-tube consists of an inner tube and an outer tube, and they are mechanically contacted to keep the heat transfer of the interface between the inner and outer tubes by their residual stress. During long term SG operation, the contact stress at the interface gradually falls down due to stress relaxation. This phenomenon might increase the thermal resistance of the interface and degrade the tube heat transfer performance. The contact stress relaxation can be predicted by numerical analysis, and the analysis requires the data of the initial residual stress distributions in the tubes. However, unclear initial residual stress distributions prevent precious relaxation evaluation. In order to resolve this issue, a neutron diffraction method was employed to reveal the tri-axial (radius, hoop and longitudinal) initial residual stress distributions in the double-wall-tube. Strain gauges also were used to evaluate the contact stress. The measurement results were analyzed using a JAEA's structural computer code to determine the initial residual stress distributions. Based on the stress distributions, the structural computer code has predicted the transition of the relaxation and the decrease of the contact stress. The radial and longitudinal temperature distributions in the tubes were input to the structural analysis model. Since the radial thermal expansion difference between the inner (colder) and outer (hotter) tube reduces the contact stress and the tube inside steam pressure contributes to increasing it, the analytical model also took these effects into consideration. It has been conduced that the inner and outer tubes are contacted with sufficient stresses during the plant life time, and that effective heat transfer degradation dose not occur in the double-wall-tube SG. (authors)

Heat transfer and thermal stress analysis in fluid-structure coupled field

International Nuclear Information System (INIS)

Li, Ming-Jian; Pan, Jun-Hua; Ni, Ming-Jiu; Zhang, Nian-Mei

2015-01-01

In this work, three-dimensional simulation on conjugate heat transfer in a fluid-structure coupled field was carried out. The structure considered is from the dual-coolant lithium-lead (DCLL) blanket, which is the key technology of International Thermo-nuclear Experimental Reactor (ITER). The model was developed based on finite element-finite volume method and was employed to investigate mechanical behaviours of Flow Channel Insert (FCI) and heat transfer in the blanket under nuclear reaction. Temperature distribution, thermal deformation and thermal stresses were calculated in this work, and the effects of thermal conductivity, convection heat transfer coefficient and flow velocity were analyzed. Results show that temperature gradients and thermal stresses of FCI decrease when FCI has better heat conductivity. Higher convection heat transfer coefficient will result in lower temperature, thermal deformations and stresses in FCI. Analysis in this work could be a theoretical basis of blanket optimization. - Highlights: • We use FVM and FEM to investigate FCI structural safety considering heat transfer and FSI effects. • Higher convective heat transfer coefficient is beneficial for the FCI structural safety without much affect to bulk flow temperature. • Smaller FCI thermal conductivity can better prevent heat leakage into helium, yet will increase FCI temperature gradient and thermal stress. • Three-dimensional simulation on conjugate heat transfer in a fluid-structure coupled field was carried out

NMR-Based Metabonomic Investigation of Heat Stress in Myotubes Reveals a Time-Dependent Change in the Metabolites

DEFF Research Database (Denmark)

Straadt, Ida K; Young, Jette F; Bross, Peter

2010-01-01

NMR-based metabonomics was applied to elucidate the time-dependent stress responses in mouse myotubes after heat exposure of either 42 or 45 degrees C for 1 h. Principal component analysis (PCA) revealed that the gradual time-dependent changes in metabolites contributing to the clustering...... and separation of the control samples from the different time points after heat stress primarily are in the metabolites glucose, leucine, lysine, phenylalanine, creatine, glutamine, and acetate. In addition, PC scores revealed a maximum change in metabolite composition 4 h after the stress exposure; thereafter......, samples returned toward control samples, however, without reaching the control samples even 10 h after stress. The results also indicate that the myotubes efficiently regulate the pH level by release of lactate to the culture medium at a heat stress level of 42 degrees C, which is a temperature level...

Work stress and the risk of recurrent coronary heart disease events: A systematic review and meta-analysis.

Science.gov (United States)

Li, Jian; Zhang, Min; Loerbroks, Adrian; Angerer, Peter; Siegrist, Johannes

2015-01-01

Though much evidence indicates that work stress increases the risk of incident of coronary heart disease (CHD), little is known about the role of work stress in the development of recurrent CHD events. The objective of this study was to review and synthesize the existing epidemiological evidence on whether work stress increases the risk of recurrent CHD events in patients with the first CHD. A systematic literature search in the PubMed database (January 1990 - December 2013) for prospective studies was performed. Inclusion criteria included: peer-reviewed English papers with original data, studies with substantial follow-up (> 3 years), end points defined as cardiac death or nonfatal myocardial infarction, as well as work stress assessed with reliable and valid instruments. Meta-analysis using random-effects modeling was conducted in order to synthesize the observed effects across the studies. Five papers derived from 4 prospective studies conducted in Sweden and Canada were included in this systematic review. The measurement of work stress was based on the Demand- Control model (4 papers) or the Effort-Reward Imbalance model (1 paper). According to the estimation by meta-analysis based on 4 papers, a significant effect of work stress on the risk of recurrent CHD events (hazard ratio: 1.65, 95% confidence interval: 1.23-2.22) was observed. Our findings suggest that, in patients with the first CHD, work stress is associated with an increased relative risk of recurrent CHD events by 65%. Due to the limited literature, more well-designed prospective research is needed to examine this association, in particular, from other than western regions of the world. This work is available in Open Access model and licensed under a CC BY-NC 3.0 PL license.

Mitigation method of thermal transient stress by thermalhydraulic-structure total analysis

International Nuclear Information System (INIS)

Kasahara, Naoto; Jinbo, Masakazu; Hosogai, Hiromi

2003-01-01

This study proposes a rational evaluation and mitigation method of thermal transient loads in fast reactor components by utilizing relationships among plant system parameters and stresses induced by thermal transients of plants. A thermalhydraulic-structure total analysis procedure helps us to grasp relationship among system parameters and thermal stresses. Furthermore, it enables mitigation of thermal transient loads by adjusting system parameters. In order to overcome huge computations, a thermalhydraulic-structure total analysis code and the Design of Experiments methodology are utilized. The efficiency of the proposed mitigation method is validated through thermal stress evaluation of an intermediate heat exchanger in Japanese demonstration fast reactor. (author)

Assessment of foam fracture in sandwich beams using thermoelastic stress analysis

DEFF Research Database (Denmark)

Dulieu-Barton, J.M.; Berggreen, Christian; Mettemberg, C.

2009-01-01

Thermoelastic Stress Analysis (TSA) has been well established for determining crack-tip parameters in metallic materials. This paper examines its ability to determine accurately the crack-tip parameters for PVC foam used in sandwich structures.......Thermoelastic Stress Analysis (TSA) has been well established for determining crack-tip parameters in metallic materials. This paper examines its ability to determine accurately the crack-tip parameters for PVC foam used in sandwich structures....

Residual stress analysis of drive shafts after induction hardening

Energy Technology Data Exchange (ETDEWEB)

Lemos, Guilherme Vieira Braga; Rocha, Alexandre da Silva; Nunes, Rafael Menezes, E-mail: lemos_gl@yahoo.com.br [Universidade Federal do Rio Grande do Sul (UFRS), Porto Algre, RS (Brazil); Hirsch, Thomas Karl [Stiftung Institut für Werkstofftechnik (IWT), Bremen (Germany)

2014-08-15

Typically, for automotive shafts, shape distortion manifests itself in most cases after the induction hardening by an effect known as bending. The distortion results in a boost of costs, especially due to machining parts in the hardened state to fabricate its final tolerances. In the present study, residual stress measurements were carried out on automotive drive shafts made of DIN 38B3 steel. The samples were selected in consequence of their different distortion properties by an industrial manufacturing line. One tested shaft was straightened, because of the considerable dimensional variation and the other one not. Firstly, the residual stress measurements were carried out by using a portable diffractometer, in order to avoid cutting the shafts and evaluate the original state of the stresses, and afterwards a more detailed analysis was realized by a conventional stationary diffractometer. The obtained results presented an overview of the surface residual stress profiles after induction hardening and displayed the influence of the straightening process on the redistribution of residual stresses. They also indicated that the effects of the straightening in the residual stresses cannot be neglected. (author)

Interference fits and stress-corrosion failure. [aircraft parts fatigue life analysis

Science.gov (United States)

Hanagud, S.; Carter, A. E.

1976-01-01

It is pointed out that any proper design of interference fit fastener, interference fit bushings, or stress coining processes should consider both the stress-corrosion susceptibility and fatigue-life improvement together. Investigations leading to such a methodology are discussed. A service failure analysis of actual aircraft parts is considered along with the stress-corrosion susceptibility of cold-working interference fit bushings. The optimum design of the amount of interference is considered, giving attention to stress formulas and aspects of design methodology.

Stress analysis of piping systems and piping supports. Documentation

International Nuclear Information System (INIS)

Rusitschka, Erwin

1999-01-01

The presentation is focused on the Computer Aided Tools and Methods used by Siemens/KWU in the engineering activities for Nuclear Power Plant Design and Service. In the multi-disciplinary environment, KWU has developed specific tools to support As-Built Documentation as well as Service Activities. A special application based on Close Range Photogrammetry (PHOCAS) has been developed to support revamp planning even in a high level radiation environment. It comprises three completely inter-compatible expansion modules - Photo Catalog, Photo Database and 3D-Model - to generate objects which offer progressively more utilization and analysis options. To support the outage planning of NPP/CAD-based tools have been developed. The presentation gives also an overview of the broad range of skills and references in: Plant Layout and Design using 3D-CAD-Tools; evaluation of Earthquake Safety (Seismic Screening); Revamps in Existing Plants; Inter-disciplinary coordination of project engineering and execution fields; Consulting and Assistance; Conceptual Studies; Stress Analysis of Piping Systems and Piping Supports; Documentation; Training and Supports in CAD-Design, etc. All activities are performed to the greatest extent possible using proven data-processing tools. (author)

Texture, residual stress and structural analysis of thin films using a combined X-ray analysis

International Nuclear Information System (INIS)

Lutterotti, L.; Chateigner, D.; Ferrari, S.; Ricote, J.

2004-01-01

Advanced thin films for today's industrial and research needs require highly specialized methodologies for a successful quantitative characterization. In particular, in the case of multilayer and/or unknown phases a global approach is necessary to obtain some or all the required information. A full approach has been developed integrating novel texture and residual stress methodologies with the Rietveld method (Acta Cryst. 22 (1967) 151) (for crystal structure analysis) and it has been coupled with the reflectivity analysis. The complete analysis can be done at once and offers several benefits: the thicknesses obtained from reflectivity can be used to correct the diffraction spectra, the phase analysis help to identify the layers and to determine the electron density profile for reflectivity; quantitative texture is needed for quantitative phase and residual stress analyses; crystal structure determination benefits of the previous. To achieve this result, it was necessary to develop some new methods, especially for texture and residual stresses. So it was possible to integrate them in the Rietveld, full profile fitting of the patterns. The measurement of these spectra required a special reflectometer/diffractometer that combines a thin parallel beam (for reflectivity) and a texture/stress goniometer with a curved large position sensitive detector. This new diffraction/reflectivity X-ray machine has been used to test the combined approach. Several spectra and the reflectivity patterns have been collected at different tilting angles and processed at once by the special software incorporating the aforementioned methodologies. Some analysis examples will be given to show the possibilities offered by the method

Stress analysis and torsional buckling analysis of U-shaped bellows

International Nuclear Information System (INIS)

Watanabe, Osamu; Ohtsubo, Hideomi.

1986-01-01

This paper presents analysis of elastic stress and torsional buckling of U-shaped bellows using ring elements. The expansion joint is considered to be composed of the two toroidal sections and inner-connecting annular plates. The general thin shell theory is employed to derive strain-displacement relations of shells and plates, valid for any loadings. Numerical examples under internal pressure or axial loading are described and compared with the results of existing appropriate analysis. The fundamental aspects of torsional buckling, which have not been studied previously, will also be investigated. (author)

Fracture mechanics and residual fatigue life analysis for complex stress fields. Technical report

International Nuclear Information System (INIS)

Besuner, P.M.

1975-07-01

This report reviews the development and application of an influence function method for calculating stress intensity factors and residual fatigue life for two- and three-dimensional structures with complex stress fields and geometries. Through elastic superposition, the method properly accounts for redistribution of stress as the crack grows through the structure. The analytical methods used and the computer programs necessary for computation and application of load independent influence functions are presented. A new exact solution is obtained for the buried elliptical crack, under an arbitrary Mode I stress field, for stress intensity factors at four positions around the crack front. The IF method is then applied to two fracture mechanics problems with complex stress fields and geometries. These problems are of current interest to the electric power generating industry and include (1) the fatigue analysis of a crack in a pipe weld under nominal and residual stresses and (2) fatigue analysis of a reactor pressure vessel nozzle corner crack under a complex bivariate stress field

Coke drums inspection and evaluation using stress and strain analysis techniques

Energy Technology Data Exchange (ETDEWEB)

Haraguchi, Marcio Issamu [Tricom Tecnologia e Servicos de Manutencao Industrial Ltda., Piquete, SP (Brazil); Samman, Mahmod [Houston Engineering Solutions, Houston, TX (United States); Tinoco, Ediberto Bastos; Marangone, Fabio de Castro; Silva, Hezio Rosa da; Barcelos, Gustavo de Carvalho [Petroleo Brasileiro S.A. (PETROBRAS), Rio de Janeiro, RJ (Brazil)

2012-07-01

Coke drums deform due to a complex combination of mechanical and thermal cyclic stresses. Bulges have progressive behavior and represent the main maintenance problem related to these drums. Bulge failure typically result in through-wall cracks, leaks, and sometimes fires. Such failures generally do not represent a great risk to personnel. Repairs needed to maintain reliability of these vessels might require extensive interruption to operation which in turn considerably impacts the profitability of the unit. Therefore the condition, progression and severity of these bulges should be closely monitored. Coke drums can be inspected during turnaround with 3D Laser Scanning and Remote Visual Inspection (RVI) tools, resulting in a detailed dimensional and visual evaluation of the internal surface. A typical project has some goals: inspect the equipment to generate maintenance or inspection recommendations, comparison with previous results and baseline data. Until recently, coke drum structural analysis has been traditionally performed analyzing Stress Concentration Factors (SCF) thought Finite Element Analysis methods; however this technique has some serious technical and practical limitations. To avoid these shortcomings, the new strain analysis technique PSI (Plastic Strain Index) was developed. This method which is based on API 579/ ASME FFS standard failure limit represents the state of the art of coke drum bulging severity assessment has an excellent correlation with failure history. (author)

Cardiorespiratory dynamic response to mental stress: a multivariate time-frequency analysis.

Science.gov (United States)

Widjaja, Devy; Orini, Michele; Vlemincx, Elke; Van Huffel, Sabine

2013-01-01

Mental stress is a growing problem in our society. In order to deal with this, it is important to understand the underlying stress mechanisms. In this study, we aim to determine how the cardiorespiratory interactions are affected by mental arithmetic stress and attention. We conduct cross time-frequency (TF) analyses to assess the cardiorespiratory coupling. In addition, we introduce partial TF spectra to separate variations in the RR interval series that are linearly related to respiration from RR interval variations (RRV) that are not related to respiration. The performance of partial spectra is evaluated in two simulation studies. Time-varying parameters, such as instantaneous powers and frequencies, are derived from the computed spectra. Statistical analysis is carried out continuously in time to evaluate the dynamic response to mental stress and attention. The results show an increased heart and respiratory rate during stress and attention, compared to a resting condition. Also a fast reduction in vagal activity is noted. The partial TF analysis reveals a faster reduction of RRV power related to (3 s) than unrelated to (30 s) respiration, demonstrating that the autonomic response to mental stress is driven by mechanisms characterized by different temporal scales.

Differential proteomic analysis reveals sequential heat stress-responsive regulatory network in radish (Raphanus sativus L.) taproot.

Science.gov (United States)

Wang, Ronghua; Mei, Yi; Xu, Liang; Zhu, Xianwen; Wang, Yan; Guo, Jun; Liu, Liwang

2018-05-01

Differential abundance protein species (DAPS) involved in reducing damage and enhancing thermotolerance in radish were firstly identified. Proteomic analysis and omics association analysis revealed a HS-responsive regulatory network in radish. Heat stress (HS) is a major destructive factor influencing radish production and supply in summer, for radish is a cool season vegetable crop being susceptible to high temperature. In this study, the proteome changes of radish taproots under 40 °C treatment at 0 h (Control), 12 h (Heat12) and 24 h (Heat24) were analyzed using iTRAQ (Isobaric Tag for Relative and Absolute Quantification) approach. In total, 2258 DAPS representing 1542 differentially accumulated uniprotein species which respond to HS were identified. A total of 604, 910 and 744 DAPS was detected in comparison of Control vs. Heat12, Control vs. Heat24, and Heat12 vs. Heat24, respectively. Gene ontology and pathway analysis showed that annexin, ubiquitin-conjugating enzyme, ATP synthase, heat shock protein (HSP) and other stress-related proteins were predominately enriched in signal transduction, stress and defense pathways, photosynthesis and energy metabolic pathways, working cooperatively to reduce stress-induced damage in radish. Based on iTRAQ combined with the transcriptomics analysis, a schematic model of a sequential HS-responsive regulatory network was proposed. The initial sensing of HS occurred at the plasma membrane, and then key components of stress signal transduction triggered heat-responsive genes in the plant protective metabolism to re-establish homeostasis and enhance thermotolerance. These results provide new insights into characteristics of HS-responsive DAPS and facilitate dissecting the molecular mechanisms underlying heat tolerance in radish and other root crops.

IEA-R1 primary and secondary coolant piping systems coupled stress analysis

International Nuclear Information System (INIS)

Fainer, Gerson; Faloppa, Altair A.; Oliveira, Carlos A.; Mattar Neto, Miguel

2013-01-01

The aim of this work is to perform the stress analysis of a coupled primary and secondary piping system of the IEA-R1 based on tridimensional model, taking into account the as built conditions. The nuclear research reactor IEA-R1 is a pool type reactor projected by Babcox-Willcox, which is operated by IPEN since 1957. The operation to 5 MW power limit was only possible after the conduction of life management and modernization programs in the last two decades. In these programs the components of the coolant systems, which are responsible for the water circulation into the reactor core to remove the heat generated inside it, were almost totally refurbished. The changes in the primary and secondary systems, mainly the replacement of pump and heat-exchanger, implied in piping layout modifications, and, therefore, the stress condition of the piping systems had to be reanalyzed. In this paper the structural stress assessment of the coupled primary and secondary piping systems is presented and the final results are discussed. (author)

Constraints on the stress state of the San Andreas fault with analysis based on core and cuttings from SAFOD drilling phases I and II

Science.gov (United States)

Lockner, David A.; Tembe, Cheryl; Wong, Teng-fong

2009-01-01

Analysis of field data has led different investigators to conclude that the San Andreas Fault (SAF) has either anomalously low frictional sliding strength (m 0.6). Arguments for the apparent weakness of the SAF generally hinge on conceptual models involving intrinsically weak gouge or elevated pore pressure within the fault zone. Some models assert that weak gouge and/or high pore pressure exist under static conditions while others consider strength loss or fluid pressure increase due to rapid coseismic fault slip. The present paper is composed of three parts. First, we develop generalized equations, based on and consistent with the Rice (1992) fault zone model to relate stress orientation and magnitude to depth-dependent coefficient of friction and pore pressure. Second, we present temperature- and pressure-dependent friction measurements from wet illite-rich fault gouge extracted from San Andreas Fault Observatory at Depth (SAFOD) phase 1 core samples and from weak minerals associated with the San Andreas Fault. Third, we reevaluate the state of stress on the San Andreas Fault in light of new constraints imposed by SAFOD borehole data. Pure talc (m0.1) had the lowest strength considered and was sufficiently weak to satisfy weak fault heat flow and stress orientation constraints with hydrostatic pore pressure. Other fault gouges showed a systematic increase in strength with increasing temperature and pressure. In this case, heat flow and stress orientation constraints would require elevated pore pressure and, in some cases, fault zone pore pressure in excess of vertical stress.

The stress components effect on the Fe-based microwires magnetostatic and magnetostrictive properties

Energy Technology Data Exchange (ETDEWEB)

Rodionova, V. [Institute of Physics & Technology and STP “Fabrika” Immanuel Kant Baltic Federal University, A. Nevskogo 14, Kaliningrad 236041 (Russian Federation); National University of Science and Technology “MISIS”, Leninsky prospect 4, Moscow 119049 (Russian Federation); Baraban, I.; Chichay, K.; Litvinova, A. [Institute of Physics & Technology and STP “Fabrika” Immanuel Kant Baltic Federal University, A. Nevskogo 14, Kaliningrad 236041 (Russian Federation); Perov, N. [Institute of Physics & Technology and STP “Fabrika” Immanuel Kant Baltic Federal University, A. Nevskogo 14, Kaliningrad 236041 (Russian Federation); Faculty of Physics, Lomonosov Moscow State University, Leninskie Gory 1-2, Moscow 119991 (Russian Federation)

2017-01-15

For glass-coated amorphous ferromagnetic Fe-based microwires both joint and separate effect of metallic nucleus diameter, d, and the ratio of metallic nucleus diameter to the total diameter of microwire in glass shell, d/D, on magnetic properties is investigated. Thereby the contribution of both shell-induced stresses, associated with the ratio of diameters, and internal nucleus stresses (residual, quenching), associated with the diameter of the nucleus are estimated. A strong and non-monotonic effect of the metallic nucleus diameter and metallic nucleus diameter/total microwire diameter ratio on magnetostatic and magnetostrictive properties was established. For analysis, we considered magnetically bi-stable microwires of “classic” Fe{sub 77.5}Si{sub 7.5}B{sub 15} alloy with positive magnetostriction coefficient.

The stress components effect on the Fe-based microwires magnetostatic and magnetostrictive properties

International Nuclear Information System (INIS)

Rodionova, V.; Baraban, I.; Chichay, K.; Litvinova, A.; Perov, N.

2017-01-01

For glass-coated amorphous ferromagnetic Fe-based microwires both joint and separate effect of metallic nucleus diameter, d, and the ratio of metallic nucleus diameter to the total diameter of microwire in glass shell, d/D, on magnetic properties is investigated. Thereby the contribution of both shell-induced stresses, associated with the ratio of diameters, and internal nucleus stresses (residual, quenching), associated with the diameter of the nucleus are estimated. A strong and non-monotonic effect of the metallic nucleus diameter and metallic nucleus diameter/total microwire diameter ratio on magnetostatic and magnetostrictive properties was established. For analysis, we considered magnetically bi-stable microwires of “classic” Fe_7_7_._5Si_7_._5B_1_5 alloy with positive magnetostriction coefficient.

3-D description of fracture surfaces and stress-sensitivity analysis for naturally fractured reservoirs

Energy Technology Data Exchange (ETDEWEB)

Zhang, S.Q.; Jioa, D.; Meng, Y.F.; Fan, Y.

1997-08-01

Three kinds of reservoir cores (limestone, sandstone, and shale with natural fractures) were used to study the effect of morphology of fracture surfaces on stress sensitivity. The cores, obtained from the reservoirs with depths of 2170 to 2300 m, have fractures which are mated on a large scale, but unmated on a fine scale. A specially designed photoelectric scanner with a computer was used to describe the topography of the fracture surfaces. Then, theoretical analysis of the fracture closure was carried out based on the fracture topography generated. The scanning results show that the asperity has almost normal distributions for all three types of samples. For the tested samples, the fracture closure predicted by the elastic-contact theory is different from the laboratory measurements because plastic deformation of the aspirates plays an important role under the testing range of normal stresses. In this work, the traditionally used elastic-contact theory has been modified to better predict the stress sensitivity of reservoir fractures. Analysis shows that the standard deviation of the probability density function of asperity distribution has a great effect on the fracture closure rate.

Stress and deflection analyses of floating roofs based on a load-modifying method

International Nuclear Information System (INIS)

Sun Xiushan; Liu Yinghua; Wang Jianbin; Cen Zhangzhi

2008-01-01

This paper proposes a load-modifying method for the stress and deflection analyses of floating roofs used in cylindrical oil storage tanks. The formulations of loads and deformations are derived according to the equilibrium analysis of floating roofs. Based on these formulations, the load-modifying method is developed to conduct a geometrically nonlinear analysis of floating roofs with the finite element (FE) simulation. In the procedure with the load-modifying method, the analysis is carried out through a series of iterative computations until a convergence is achieved within the error tolerance. Numerical examples are given to demonstrate the validity and reliability of the proposed method, which provides an effective and practical numerical solution to the design and analysis of floating roofs

Recommendations for analysis of stress corrosion in pipe systems exposed to thermohydraulic transients

International Nuclear Information System (INIS)

Bjoerndahl, Olof; Letzter, Adam; Marcinkiewicz, Jerzy; Segle, Peter

2007-03-01

Transient thermohydraulic events often control the design of piping systems in nuclear power plants. Water hammers due to valve closure, pressure transients caused by steam collapse and pipe break all result in structural loads that are characterised by a high frequency content. What also characterises these pressures/forces is the specific spatial and time dependence that is acting on the piping system and found in the wave propagation in the contained fluid. The aim with this project has been to develop recommendations for analysis of the stress response in piping systems subjected to thermohydraulic transients. Basis for this work is that the so called two-step-method is applied and that the structural response is calculated with modal superposition. Derived analysis criteria are based on the assumption that the associated volume strain energy in the wave propagation for the contained fluid may be well defined by a parameter, here called ε PN . The stress response in the piping system is assumed to be completely determined with certain accuracy for that part of the volume strain energy in the wave propagation associated with this parameter. A comprehensive work has been done to determine the accuracy in loadings calculated with RELAP5. Properties such as period elongation and associated spurious oscillations in the pressure wave transient have been investigated. Furthermore, has the characteristics of the artificial numerical damping in RELAP5 been identified. Based on desired accuracy of the thermohydraulic analysis together with knowledge about the duration of the thermohydraulic perturbation, the lowest upper frequency limit f Pipe , in the modal base that is required for the structure model is calculated. With perturbation is meant such as a valve closure. According to suggested criteria and with the upper frequency limit set, the essential parameters i) largest size of the elements in the structure model and ii) the largest applicable time step in the

Background Stress Inventory: Developing a Measure of Understudied Stress.

Science.gov (United States)

Terrill, Alexandra L; Gjerde, Jill M; Garofalo, John P

2015-10-01

Background stress is an understudied source of stress that involves both ambient stress and daily hassles upon which new stressors are superimposed. To date, an accurate measure of the background stress construct has not been available. We developed the Background Stress Inventory, a 25-item self-report measure that asks respondents to indicate how distressed they have felt over the past month and the majority of the past year across five domains: financial, occupation, environment, health and social. Seven hundred seventy-two participants completed the paper-and-pencil measure; the sample was randomly split into two separate subsamples for analyses. Exploratory factor analysis suggested five factors corresponding to these domains, and confirmatory factor analysis showed acceptable global fit (X(2)(255) = 456.47, comparative fit index = 0.94, root mean square error of approximation = 0.045). Cronbach's alpha (0.89) indicated good internal reliability. Construct validity analyses showed significant positive relationships with measures of perceived stressfulness (r = 0.62) and daily hassles (0.41), p's < 0.01. Depressive symptoms (0.62) and basal blood pressure (0.21) were both significantly associated with background stress, p's < 0.01. The importance of the proposed measure is reflected in the limited research base on the impact of background stress. Systematic investigation of this measure will provide insight into this understudied form of chronic stress and its potential influence on both psychological and physical endpoints. Copyright © 2013 John Wiley & Sons, Ltd.

StressPhone: smartphone based platform for measurement of cortisol for stress detection (Conference Presentation)

Science.gov (United States)

Jain, Aadhar; Rey, Elizabeth; Lee, Seoho; O'Dell, Dakota; Erickson, David

2016-03-01

Anxiety disorders are estimated to be the most common mental illness in US affecting around 40 million people and related job stress is estimated to cost US industry up to $300 billion due to lower productivity and absenteeism. A personal diagnostic device which could help identify stressed individuals would therefore be a huge boost for workforce productivity. We are therefore developing a point of care diagnostic device that can be integrated with smartphones or tablets for the measurement of cortisol - a stress related salivary biomarker, which is known to be strongly involved in body's fight-or-flight response to a stressor (physical or mental). The device is based around a competitive lateral flow assay whose results can then be read and quantified through an accessory compatible with the smartphone. In this presentation, we report the development and results of such an assay and the integrated device. We then present the results of a study relating the diurnal patterns of cortisol levels and the alertness of an individual based on the circadian rhythm and sleep patterns of the individual. We hope to use the insight provided by combining the information provided by levels of stress related to chemical biomarkers of the individual with the physical biomarkers to lead to a better informed and optimized activity schedule for maximized work output.

Reducing composite restoration polymerization shrinkage stress through resin modified glass-ionomer based adhesives.

Science.gov (United States)

Naoum, S J; Mutzelburg, P R; Shumack, T G; Thode, Djg; Martin, F E; Ellakwa, A E

2015-12-01

The aim of this study was to determine whether employing resin modified glass-ionomer based adhesives can reduce polymerization contraction stress generated at the interface of restorative composite adhesive systems. Five resin based adhesives (G Bond, Optibond-All-in-One, Optibond-Solo, Optibond-XTR and Scotchbond-Universal) and two resin modified glass-ionomer based adhesives (Riva Bond-LC, Fuji Bond-LC) were analysed. Each adhesive was applied to bond restorative composite Filtek-Z250 to opposing acrylic rods secured within a universal testing machine. Stress developed at the interface of each adhesive-restorative composite system (n = 5) was calculated at 5-minute intervals over 6 hours. The resin based adhesive-restorative composite systems (RBA-RCS) demonstrated similar interface stress profiles over 6 hours; initial rapid contraction stress development (0-300 seconds) followed by continued contraction stress development ≤0.02MPa/s (300 seconds - 6 hours). The interface stress profile of the resin modified glass-ionomer based adhesive-restorative composite systems (RMGIBA-RCS) differed substantially to the RBA-RCS in several ways. Firstly, during 0-300 seconds the rate of contraction stress development at the interface of the RMGIBA-RCS was significantly (p adhesives can significantly reduce the magnitude and rate of polymerization contraction stress developed at the interface of adhesive-restorative composite systems. © 2015 Australian Dental Association.

The interaction of fatigue cracks with a residual stress field using thermoelastic stress analysis and synchrotron X-ray diffraction experiments

Science.gov (United States)

Amjad, Khurram; Asquith, David; Sebastian, Christopher M.; Wang, Wei-Chung

2017-01-01

This article presents an experimental study on the fatigue behaviour of cracks emanating from cold-expanded holes utilizing thermoelastic stress analysis (TSA) and synchrotron X-ray diffraction (SXRD) techniques with the aim of resolving the long-standing ambiguity in the literature regarding potential relaxation, or modification, of beneficial compressive residual stresses as a result of fatigue crack propagation. The crack growth rates are found to be substantially lower as the crack tip moved through the residual stress zone induced by cold expansion. The TSA results demonstrated that the crack tip plastic zones were reduced in size by the presence of the residual compressive stresses induced by cold expansion. The crack tip plastic zones were found to be insignificant in size in comparison to the residual stress zone resulting from cold expansion, which implied that they were unlikely to have had a notable impact on the surrounding residual stresses induced by cold expansion. The residual stress distributions measured along the direction of crack growth, using SXRD, showed no signs of any significant stress relaxation or redistribution, which validates the conclusions drawn from the TSA data. Fractographic analysis qualitatively confirmed the influence on crack initiation of the residual stresses induced by the cold expansion. It was found that the application of single compressive overload caused a relaxation, or reduction in the residual stresses, which has wider implications for improving the fatigue life. PMID:29291095

A flexible method for residual stress measurement of spray coated layers by laser made hole drilling and SLM based beam steering

Science.gov (United States)

Osten, W.; Pedrini, G.; Weidmann, P.; Gadow, R.

2015-08-01

A minimum invasive but high resolution method for residual stress analysis of ceramic coatings made by thermal spraycoating using a pulsed laser for flexible hole drilling is described. The residual stresses are retrieved by applying the measured surface data for a model-based reconstruction procedure. While the 3D deformations and the profile of the machined area are measured with digital holography, the residual stresses are calculated by FE analysis. To improve the sensitivity of the method, a SLM is applied to control the distribution and the shape of the holes. The paper presents the complete measurement and reconstruction procedure and discusses the advantages and challenges of the new technology.

Integrated transcriptomic and proteomic analysis of the bile stress response in probiotic Lactobacillus salivarius LI01.

Science.gov (United States)

Lv, Long-Xian; Yan, Ren; Shi, Hai-Yan; Shi, Ding; Fang, Dai-Qiong; Jiang, Hui-Yong; Wu, Wen-Rui; Guo, Fei-Fei; Jiang, Xia-Wei; Gu, Si-Lan; Chen, Yun-Bo; Yao, Jian; Li, Lan-Juan

2017-01-06

Lactobacillus salivarius LI01, isolated from healthy humans, has demonstrated probiotic properties in the prevention and treatment of liver failure. Tolerance to bile stress is crucial to allow lactobacilli to survive in the gastrointestinal tract and exert their benefits. In this work, we used a Digital Gene Expression transcriptomic and iTRAQ LC-MS/MS proteomic approach to examine the characteristics of LI01 in response to bile stress. Using culture medium with or without 0.15% ox bile, 591 differentially transcribed genes and 347 differentially expressed proteins were detected in LI01. Overall, we found the bile resistance of LI01 to be based on a highly remodeled cell envelope and a reinforced bile efflux system rather than on the activity of bile salt hydrolases. Additionally, some differentially expressed genes related to regulatory systems, the general stress response and central metabolism processes, also play roles in stress sensing, bile-induced damage prevention and energy efficiency. Moreover, bile salts appear to enhance proteolysis and amino acid uptake (especially aromatic amino acids) by LI01, which may support the liver protection properties of this strain. Altogether, this study establishes a model of global response mechanism to bile stress in L. salivarius LI01. L. salivarius strain LI01 exhibits not only antibacterial and antifungal properties but also exerts a good health-promoting effect in acute liver failure. As a potential probiotic strain, the bile-tolerance trait of strain LI01 is important, though this has not yet been explored. In this study, an analysis based on DGE and iTRAQ was performed to investigate the gene expression in strain LI01 under bile stress at the mRNA and protein levels, respectively. To our knowledge, this work also represents the first combined transcriptomic and proteomic analysis of the bile stress response mechanism in L. salivarius. Copyright © 2016. Published by Elsevier B.V.

Loading and Contact Stress Analysis on the Thread Teeth in Tubing and Casing Premium Threaded Connection

Directory of Open Access Journals (Sweden)

Honglin Xu

2014-01-01

Full Text Available Loading and contact stress distribution on the thread teeth in tubing and casing premium threaded connections are of great importance for design optimization, pretightening force control, and thread failure prevention. This paper proposes an analytical method based on the elastic mechanics. This is quite different from other papers, which mainly rely on finite element analysis. The differential equation of load distribution on the thread teeth was established according to equal pitch of the engaged thread after deformation and solved by finite difference method. Furthermore, the relation between load acting on each engaged thread and mean contact stress on its load flank is set up based on the geometric description of thread surface. By comparison, this new analytical method with the finite element analysis for a modified API 177.8 mm premium threaded connection is approved. Comparison of the contact stress on the last engaged thread between analytical model and FEM shows that the accuracy of analytical model will decline with the increase of pretightening force after the material enters into plastic deformation. However, the analytical method can meet the needs of engineering to some extent because its relative error is about 6.2%~18.1% for the in-service level of pretightening force.

12 CFR 652.100 - Audit of the risk-based capital stress test.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 6 2010-01-01 2010-01-01 false Audit of the risk-based capital stress test... AGRICULTURAL MORTGAGE CORPORATION FUNDING AND FISCAL AFFAIRS Risk-Based Capital Requirements § 652.100 Audit of the risk-based capital stress test. You must have a qualified, independent external auditor review...

Stress analysis of the tokamak engineering test breeder blanket

International Nuclear Information System (INIS)

Huang Zhongqi

1992-01-01

The design features of the hybrid reactor blanket and main parameters are presented. The stress analysis is performed by using computer codes SAP5p and SAP6 with the three kinds of blanket module loadings, i.e, the pressure of coolant, the blanket weight and the thermal loading. Numerical calculation results indicate that the stresses of the blanket are smaller than the allowable ones of the material, the blanket design is therefore reasonable

Stress analysis and collapse time prediction of nuclear fuel cladding tube with wear scar

International Nuclear Information System (INIS)

Lee, J. S.; Kim, O. H.; Kim, H. K.; Hu, Y. H.; Kim, J. I.; Kim, K. T.

2004-01-01

In this analysis, the stress and collapse time analysis models for nuclear fuel rod with the fretting wear scar were developed in order to evaluate the effects of the wear depth on the integrity of nuclear fuel rod. The stress analysis result shows that the nuclear fuel rod with approximately 60% deep wear scar of the clad wall thickness, meets the allowable stress criteria and the collapse time analysis indicates that the fuel rod with less than roughly 56% deep wear scar of the clad wall thickness has longer collapse time than the expected fuel life-time. The both stress and collapse time results are evaluated to be very reasonable on considering the comparison with the outputs of existing design code for the simple model. However, the developed analysis models and the results will be confirmed by the tests

Dynamical System Analysis of Reynolds Stress Closure Equations

Science.gov (United States)

Girimaji, Sharath S.

1997-01-01

In this paper, we establish the causality between the model coefficients in the standard pressure-strain correlation model and the predicted equilibrium states for homogeneous turbulence. We accomplish this by performing a comprehensive fixed point analysis of the modeled Reynolds stress and dissipation rate equations. The results from this analysis will be very useful for developing improved pressure-strain correlation models to yield observed equilibrium behavior.

Cold-Rolled Strip Steel Stress Detection Technology Based on a Magnetoresistance Sensor and the Magnetoelastic Effect.

Science.gov (United States)

Guan, Ben; Zang, Yong; Han, Xiaohui; Zheng, Kailun

2018-05-21

Driven by the demands for contactless stress detection, technologies are being used for shape control when producing cold-rolled strips. This paper presents a novel contactless stress detection technology based on a magnetoresistance sensor and the magnetoelastic effect, enabling the detection of internal stress in manufactured cold-rolled strips. An experimental device was designed and produced. Characteristics of this detection technology were investigated through experiments assisted by theoretical analysis. Theoretically, a linear correlation exists between the internal stress of strip steel and the voltage output of a magneto-resistive sensor. Therefore, for this stress detection system, the sensitivity of the stress detection was adjusted by adjusting the supply voltage of the magnetoresistance sensor, detection distance, and other relevant parameters. The stress detection experimental results showed that this detection system has good repeatability and linearity. The detection error was controlled within 1.5%. Moreover, the intrinsic factors of the detected strip steel, including thickness, carbon percentage, and crystal orientation, also affected the sensitivity of the detection system. The detection technology proposed in this research enables online contactless detection and meets the requirements for cold-rolled steel strips.

Evaluation of an app-based stress protocol

Directory of Open Access Journals (Sweden)

Noeh Claudius

2016-09-01

Full Text Available Stress is a major influence on the quality of life in our fast-moving society. This paper describes a standardized and contemporary protocol that is capable of inducing moderate psychological stress in a laboratory setting. Furthermore, it evaluates its effects on physiological biomarkers. The protocol called “THM-Stresstest” mainly consists of a rest period (30 min, an app-based stress test under the surveillance of an audience (4 min and a regeneration period (32 min. We investigated 12 subjects to evaluate the developed protocol. We could show significant changes in heart rate variability, electromyography, electro dermal activity and salivary cortisol and α-amylase. From this data we conclude that the THM-Stresstest can serve as a psychobiological tool for provoking responses in the cardiovascular-, the endocrine and exocrine system as well as the sympathetic part of the central nervous system.

Relations of occupational stress to occupational class in Japanese civil servants : analysis by two occupational stress models

OpenAIRE

Kawaharada, Mariko; Saijo, Yasuaki; Yoshioka, Eiji; Sato, Tetsuro; Sato, Hirokazu; Kishi, Reiko

2007-01-01

The aim of the present study was to identify relations between occupational stress and occupational class in Japanese civil servants, using two occupational stress models – the Effort-Reward Imbalance (ERI) Model and the Job Demand-Control (JDC) Model. The subjects were employees of three local public organizations. We distributed self-administered questionnaires and assessed occupational stress by ERI and JDC. We used seven occupational categories based on the Standard Occupational Classific...

Piping stress analysis with personal computers

International Nuclear Information System (INIS)

Revesz, Z.

1987-01-01

The growing market of the personal computers is providing an increasing number of professionals with unprecedented and surprisingly inexpensive computing capacity, which if using with powerful software, can enhance immensely the engineers capabilities. This paper focuses on the possibilities which opened in piping stress analysis by the widespread distribution of personal computers, on the necessary changes in the software and on the limitations of using personal computers for engineering design and analysis. Reliability and quality assurance aspects of using personal computers for nuclear applications are also mentioned. The paper resumes with personal views of the author and experiences gained during interactive graphic piping software development for personal computers. (orig./GL)

Intraplaque hemorrhage is associated with higher structural stresses in human atherosclerotic plaques: an in vivo MRI-based 3D fluid-structure interaction study.

Science.gov (United States)

Huang, Xueying; Teng, Zhongzhao; Canton, Gador; Ferguson, Marina; Yuan, Chun; Tang, Dalin

2010-12-31

Studies using medical images have shown that intraplaque hemorrhage may accelerate plaque progression and may produce a stimulus for atherosclerosis development by increasing lipid core and plaque volume and creating new destabilizing factors. Image-based 3D computational models with fluid-structure interactions (FSI) will be used to perform plaque mechanical analysis and investigate possible associations between intraplaque hemorrhage and both plaque wall stress (PWS) and flow shear stress (FSS). In vivo MRI data of carotid plaques from 5 patients with intraplaque hemorrhage confirmed by histology were acquired. 3D multi-component FSI models were constructed for each plaque to obtain mechanical stresses. Plaque Wall Stress (PWS) and Flow Shear Stress (FSS) were extracted from all nodal points on the lumen surface of each plaque for analysis. The mean PWS value from all hemorrhage nodes of the 5 plaques combined was higher than that from non-hemorrhage nodes (75.6 versus 68.1 kPa, P = 0.0003). The mean PWS values from hemorrhage nodes for each of the 5 plaques were all significantly higher (5 out of 5) than those from non-hemorrhage nodes (P shear stress values from individual cases showed mixed results: only one out of five plaques showed mean FSS value from hemorrhage nodes was higher than that from non-hemorrhage nodes; three out of five plaques showed that their mean FSS values from hemorrhage nodes were lower than those from non-hemorrhage nodes; and one plaque showed that the difference had no statistical significance. The results of this study suggested that intraplaque hemorrhage nodes were associated with higher plaque wall stresses. Compared to flow shear stress, plaque wall stress has a better correlation with plaque component feature (hemorrhage) linked to plaque progression and vulnerability. With further validation, plaque stress analysis may provide additional stress indicators for image-based vulnerability assessment.

Stress analysis in high-temperature superconductors under pulsed field magnetization

Science.gov (United States)

Wu, Haowei; Yong, Huadong; Zhou, Youhe

2018-04-01

Bulk high-temperature superconductors (HTSs) have a high critical current density and can trap a large magnetic field. When bulk superconductors are magnetized by the pulsed field magnetization (PFM) technique, they are also subjected to a large electromagnetic stress, and the resulting thermal stress may cause cracking of the superconductor due to the brittle nature of the sample. In this paper, based on the H-formulation and the law of heat transfer, we can obtain the distributions of electromagnetic field and temperature, which are in qualitative agreement with experiment. After that, based on the dynamic equilibrium equations, the mechanical response of the bulk superconductor is determined. During the PFM process, the change in temperature has a dramatic effect on the radial and hoop stresses, and the maximum radial and hoop stress are 24.2 {{MPa}} and 22.6 {{MPa}}, respectively. The mechanical responses of a superconductor for different cases are also studied, such as the peak value of the applied field and the size of bulk superconductors. Finally, the stresses are also presented for different magnetization methods.

A Study on the Job Stress Assessment in Korean Nuclear Power Plants based on KOSS

Energy Technology Data Exchange (ETDEWEB)

Hwang, Seong Hwan; Lee, Yong Hee; Lee, Jung Woon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Sung, Sook Hee; Jung, Kwang Hee; Jung, Yeon Sub [Korea Hydro and Nuclear Power Co., Daejeon (Korea, Republic of)

2010-05-15

Job stress is a harmful physical and emotional response that occurs when there is a poor match between job demands and the capabilities, resources, or needs of the worker. Stress-related disorders encompass a broad array of conditions, including psychological disorders (e.g., depression, anxiety, posttraumatic stress disorder) and other types of emotional strain (e.g., dissatisfaction, fatigue, tension, etc.), maladaptive behaviors (e.g., aggression, substance abuse), and cognitive impairment (e.g., concentration and memory problems). In turn, these conditions may lead to poor work performance or even injury. Job stress is also associated with various biological reactions that may lead ultimately to compromised health, such as cardiovascular disease or in extreme cases, death. In Korea, organizational job stress factors were investigated for the jobs in nuclear power plants that are operated based on procedures. Especially, the occupational stress scale for Korean employees (KOSS) was developed. The KOSS has 8 subscales by using a factor analysis and validation process in order to measure stress at work and to find methods for the prevention of stressors. In this point of view, the RHRI (Radiation Health Research Institute of KHNP (Korea Hydro and Nuclear Power) assessed how wellsuited employees were for their job during their health examination in 2009. In this study the present condition of employee's stress level is investigated to find a way to manage their stressors

A Study on the Job Stress Assessment in Korean Nuclear Power Plants based on KOSS

International Nuclear Information System (INIS)

Hwang, Seong Hwan; Lee, Yong Hee; Lee, Jung Woon; Sung, Sook Hee; Jung, Kwang Hee; Jung, Yeon Sub

2010-01-01

Job stress is a harmful physical and emotional response that occurs when there is a poor match between job demands and the capabilities, resources, or needs of the worker. Stress-related disorders encompass a broad array of conditions, including psychological disorders (e.g., depression, anxiety, posttraumatic stress disorder) and other types of emotional strain (e.g., dissatisfaction, fatigue, tension, etc.), maladaptive behaviors (e.g., aggression, substance abuse), and cognitive impairment (e.g., concentration and memory problems). In turn, these conditions may lead to poor work performance or even injury. Job stress is also associated with various biological reactions that may lead ultimately to compromised health, such as cardiovascular disease or in extreme cases, death. In Korea, organizational job stress factors were investigated for the jobs in nuclear power plants that are operated based on procedures. Especially, the occupational stress scale for Korean employees (KOSS) was developed. The KOSS has 8 subscales by using a factor analysis and validation process in order to measure stress at work and to find methods for the prevention of stressors. In this point of view, the RHRI (Radiation Health Research Institute of KHNP (Korea Hydro and Nuclear Power) assessed how wellsuited employees were for their job during their health examination in 2009. In this study the present condition of employee's stress level is investigated to find a way to manage their stressors

Analysis of heat transfer and stress in the pipe with hot fluid flowing through

International Nuclear Information System (INIS)

Charoensri, Apisara; Pichestapong, Pipat; Rodthongkom, Chouvana

2003-10-01

At incomplete mixing area of high temperature and low temperature liquid near the surface of structures, temperature fluctuation of liquid gives thermal fatigue damage to wall structure. This phenomenon is called thermal striping. For designing of piping system, it is important to know thermal stresses of structure due to heat convection. In this study, authors proposed a simplified evaluation method to predict thermal stress from temperature fluctuation, for rational design against thermal striping. It is required to estimate structural responses to temperature fluctuation of fluid. The attenuation process is a thermal coupling problem between fluids and structures and has a sensitive characteristics to frequencies of temperature fluctuations were analyzed by FINAS, which is a computer program based on the finite element method by comparisons of theoretical method. When the inner surface of the pipe is due to heat convection of contained fluid with sinusoidal temperature fluctuation and the outer surface is kept insulated, temperature distribution of structure is analyzed by solving the equation of transient heat conduction. From these temperature distributions, induced thermal stresses in the structure are calculated by thermal elastic analysis. Frequency response characteristics of structures and its mechanism were investigated by both numerical and theoretical methods. Based on above investigation, a structural response diagram was derived, which can predict stress amplitude of structures from temperature amplitude and frequency of fluids

Calculation method for residual stress analysis of filament-wound spherical pressure vessels

International Nuclear Information System (INIS)

Knight, C.E. Jr.

1976-01-01

Filament wound spherical pressure vessels may be produced with very high performance factors. These performance factors are a calculation of contained pressure times enclosed volume divided by structure weight. A number of parameters are important in determining the level of performance achieved. One of these is the residual stress state in the fabricated unit. A significant level of an unfavorable residual stress state could seriously impair the performance of the vessel. Residual stresses are of more concern for vessels with relatively thick walls and/or vessels constructed with the highly anisotropic graphite or aramid fibers. A method is established for measuring these stresses. A theoretical model of the composite structure is required. Data collection procedures and techniques are developed. The data are reduced by means of the model and result in the residual stress analysis. The analysis method can be used in process parameter studies to establish the best fabrication procedures

Web-based psychotherapy for posttraumatic stress disorder in war-traumatized Arab patients: randomized controlled trial.

Science.gov (United States)

Knaevelsrud, Christine; Brand, Janine; Lange, Alfred; Ruwaard, Jeroen; Wagner, Birgit

2015-03-20

In recent years, armed conflicts in the Middle East have resulted in high rates of exposure to traumatic events. Despite the increasing demand of mental health care provision, ongoing violence limits conventional approaches of mental health care provision. Internet-based interventions for posttraumatic stress disorder (PTSD) have proved feasible and effective in Western countries, but their applicability and efficacy in war and conflict regions remains unknown. This study investigated the efficacy of a cognitive behavioral Internet-based intervention for war-traumatized Arab patients, with focus on Iraq. A total of 159 individuals with PTSD participated in a parallel group randomized trial. Participants were randomly allocated by a computer-generated sequence to a treatment group (n=79) or a waiting list control group (n=80). The treatment group received 2 weekly 45-minute cognitive behavioral interventions via Internet over a 5-week period (10 sessions in total). The primary outcome was recovery from posttraumatic stress symptoms. Posttraumatic stress symptoms were significantly reduced from baseline to posttreatment (intention-to-treat analysis) in the treatment group relative to the control group (F1,157=44.29, Pposttraumatic stress symptoms at posttreatment (reliable change and Posttraumatic Stress Diagnostic Scale score posttraumatic stress symptoms benefit from a cognitive behavioral treatment provided entirely through the Internet. This method of delivery could improve patients' access to humanitarian aid in the form of e-mental health services. Australian New Zealand Clinical Trial Registry, ACTRN12611001019998; https://www.anzctr.org.au/Trial/Registration/TrialReview.aspx?id=347505 (Archived by WebCite at http://www.webcitation.org/6Wto4HCdH).

Stress Response of Veterinary Students to Gynaecological Examination of Horse Mares - Effects of Simulator-Based and Animal-Based Training.

Science.gov (United States)

Nagel, C; Ille, N; Erber, R; Aurich, C; Aurich, J

2015-10-01

Invasive procedures in animals are challenging for veterinary students who may perceive a gynaecological examination of mares as stressful. Simulator-based training may reduce stress. In this study, students received equine gynaecology training 4 times either on horses (group H; n = 14) or a teaching simulator (group SIM; n = 13). One day and 14 days thereafter, their diagnostic skills were tested on horses (skills tests 1 and 2). During the skills tests, the students' stress response was analysed by heart rate, heart rate variability (HRV) parameters SDRR (standard deviation of beat-to-beat [RR] interval) and RMSSD (root-mean-square of successive RR differences), and salivary cortisol. In addition, students answered a questionnaire on their perceived stress. Sympathetic activation with increased heart rate (p stress response. Subjective stress perception of students was higher in skills test 1 vs 2 (p stressed than SIM students (p stress parameters. In conclusion, gynaecological examination of mares evoked a moderate stress response in veterinary students, which was more evident after simulator-based than animal-based training. © 2015 Blackwell Verlag GmbH.

Global analysis of WRKY transcription factor superfamily in Setaria identifies potential candidates involved in abiotic stress signaling.

Science.gov (United States)

Muthamilarasan, Mehanathan; Bonthala, Venkata S; Khandelwal, Rohit; Jaishankar, Jananee; Shweta, Shweta; Nawaz, Kashif; Prasad, Manoj

2015-01-01

Transcription factors (TFs) are major players in stress signaling and constitute an integral part of signaling networks. Among the major TFs, WRKY proteins play pivotal roles in regulation of transcriptional reprogramming associated with stress responses. In view of this, genome- and transcriptome-wide identification of WRKY TF family was performed in the C4model plants, Setaria italica (SiWRKY) and S. viridis (SvWRKY), respectively. The study identified 105 SiWRKY and 44 SvWRKY proteins that were computationally analyzed for their physicochemical properties. Sequence alignment and phylogenetic analysis classified these proteins into three major groups, namely I, II, and III with majority of WRKY proteins belonging to group II (53 SiWRKY and 23 SvWRKY), followed by group III (39 SiWRKY and 11 SvWRKY) and group I (10 SiWRKY and 6 SvWRKY). Group II proteins were further classified into 5 subgroups (IIa to IIe) based on their phylogeny. Domain analysis showed the presence of WRKY motif and zinc finger-like structures in these proteins along with additional domains in a few proteins. All SiWRKY genes were physically mapped on the S. italica genome and their duplication analysis revealed that 10 and 8 gene pairs underwent tandem and segmental duplications, respectively. Comparative mapping of SiWRKY and SvWRKY genes in related C4 panicoid genomes demonstrated the orthologous relationships between these genomes. In silico expression analysis of SiWRKY and SvWRKY genes showed their differential expression patterns in different tissues and stress conditions. Expression profiling of candidate SiWRKY genes in response to stress (dehydration and salinity) and hormone treatments (abscisic acid, salicylic acid, and methyl jasmonate) suggested the putative involvement of SiWRKY066 and SiWRKY082 in stress and hormone signaling. These genes could be potential candidates for further characterization to delineate their functional roles in abiotic stress signaling.

Thermal stratification and fatigue stress analysis for pressurizer surge line

International Nuclear Information System (INIS)

Yu Xiaofei; Zhang Yixiong

2011-01-01

Thermal stratification of pressurizer surge line induced by the inside fluid results in the global bending moments, local thermal stresses, unexpected displacements and support loadings of the pipe system. In order to avoid a costly three-dimensional computation, a combined 1D/2D technique has been developed and implemented to analyze the thermal stratification and fatigue stress of pressurize surge line of QINSHAN Phase II Extension Nuclear Power Project in this paper, using the computer codes SYSTUS and ROCOCO. According to the mechanical analysis results of stratification, the maximum stress and cumulative usage factor are obtained. The results indicate that the stress and fatigue intensity considering thermal stratification satisfies RCC-M criterion. (authors)

Analysis of Simple Creep Stress Calculation Methods for Creep Life Assessment

Energy Technology Data Exchange (ETDEWEB)

Seo, Jun Min; Lee, Han Sang; Kim, Yun Jae [Korea Univ., Daejeon (Korea, Republic of)

2017-08-15

Creep analysis takes much more time than elastic or elastic-plastic analysis. In this study, we conducted elastic and elastic-plastic analysis and compared the results with creep analysis results. In the elastic analysis, we used primary stress, which can be classified by the Mα-tangent method and stress intensities recommended in the ASME code. In the elastic-plastic analysis, we calculated the parameters recommended in the R5 code. For the FE models, a bending load, uniaxial load, and biaxial load were applied to the cross shaped welded plate, and a bending load and internal pressure were applied to the elbow pipe. To investigate the element size sensitivity, we conducted FE analysis for various element sizes for the cases where bending load was applied to the cross shaped welded plate. There was no significant difference between the creep.

Deep Transcriptomic Analysis of Black Rockfish (Sebastes schlegelii) Provides New Insights on Responses to Acute Temperature Stress.

Science.gov (United States)

Lyu, Likang; Wen, Haishen; Li, Yun; Li, Jifang; Zhao, Ji; Zhang, Simin; Song, Min; Wang, Xiaojie

2018-06-14

In the present study, we conducted an RNA-Seq analysis to characterize the genes and pathways involved in acute thermal and cold stress responses in the liver of black rockfish, a viviparous teleost that has the ability to cope with a wide range of temperature changes. A total of 584 annotated differentially expressed genes (DEGs) were identified in all three comparisons (HT vs NT, HT vs LT and LT vs NT). Based on an enrichment analysis, DEGs with a potential role in stress accommodation were classified into several categories, including protein folding, metabolism, immune response, signal transduction, molecule transport, membrane, and cell proliferation/apoptosis. Considering that thermal stress has a greater effect than cold stress in black rockfish, 24 shared DEGs in the intersection of the HT vs LT and HT vs NT groups were enriched in 2 oxidation-related gene ontology (GO) terms. Nine important heat-stress-reducing pathways were significantly identified and classified into 3 classes: immune and infectious diseases, organismal immune system and endocrine system. Eight DEGs (early growth response protein 1, bile salt export pump, abcb11, hsp70a, rtp3, 1,25-dihydroxyvitamin d(3) 24-hydroxylase, apoa4, transcription factor jun-b-like and an uncharacterized gene) were observed among all three comparisons, strongly implying their potentially important roles in temperature stress responses.

Cluster analysis of stress corrosion mechanisms for steel wires used in bridge cables through acoustic emission particle swarm optimization.

Science.gov (United States)

Li, Dongsheng; Yang, Wei; Zhang, Wenyao

2017-05-01

Stress corrosion is the major failure type of bridge cable damage. The acoustic emission (AE) technique was applied to monitor the stress corrosion process of steel wires used in bridge cable structures. The damage evolution of stress corrosion in bridge cables was obtained according to the AE characteristic parameter figure. A particle swarm optimization cluster method was developed to determine the relationship between the AE signal and stress corrosion mechanisms. Results indicate that the main AE sources of stress corrosion in bridge cables included four types: passive film breakdown and detachment of the corrosion product, crack initiation, crack extension, and cable fracture. By analyzing different types of clustering data, the mean value of each damage pattern's AE characteristic parameters was determined. Different corrosion damage source AE waveforms and the peak frequency were extracted. AE particle swarm optimization cluster analysis based on principal component analysis was also proposed. This method can completely distinguish the four types of damage sources and simplifies the determination of the evolution process of corrosion damage and broken wire signals. Copyright © 2017. Published by Elsevier B.V.

Residual stress analysis in carbon fiber-reinforced SiC ceramics

International Nuclear Information System (INIS)

Broda, M.

1998-01-01

Systematic residual stress analyses are reported, carried out in long-fiber reinforced SiC ceramics. The laminated C fiber /SiC matrix specimens used were prepared by polymer pyrolysis, and the structural component specimens used are industrial products. Various diffraction methods have been applied for non-destructive evaluation of residual stress fields, so as to completely detect the residual stresses and their distribution in the specimens. The residual stress fields at the surface (μm) have been measured using characteristic X-radiation and applying the sin 2 ψ method as well as the scatter vector method. For residual stress field analysis in the mass volume (cm), neutron diffraction has been applied. The stress fields in the fiber layers (approx. 250μm) have been measured as a function of their location within the laminated composite by using an energy-dispersive method and synchrotron radiation. By means of the systematic, process-accompanying residual stress and phase analyses, conclusions can be drawn as to possible approaches for optimization of fabrication parameters. (orig./CB) [de

Three dimensional, thermal stress analysis of a welded plate

International Nuclear Information System (INIS)

Koening, H.A.; Lai, C.K.-F.; Morral, J.E.

1985-01-01

A general finite element thermal stress analysis has been developed. The analysis can be uncoupled to solve either the heat transfer problem or the stress problem independently and it can accommodate non-linear material behavior, initial states of stress and strain, and moving boundary conditions. A unique feature of the model it that it properly accounts for the latent heat effect during phase changes. Applying the moving heat flux boundary condition to simulate arc welding, the model has been used to predict the transient thermal mechanical response of a welded plate. It is the absorption and liberation of latent heat in the fusion zone of a weld which complicates numerical methods of treating welding. For pure materials and eutectic alloys the latent heat effect is less of a problem because phase changes take place at a specific temperature. But for most alloys, phase changes take place over a range of temperatures bounded by the solidus, T S , and liquidus, T L , and the latent heat effect occurs continuously over the temperature range. (author)

Effect of mindfulness-based stress reduction on sleep quality

DEFF Research Database (Denmark)

Andersen, Signe; Würtzen, Hanne; Steding-Jessen, Marianne

2013-01-01

The prevalence of sleep disturbance is high among cancer patients, and the sleep problems tend to last for years after the end of treatment. As part of a large randomized controlled clinical trial (the MICA trial, NCT00990977) of the effect of mindfulness-based stress reduction (MBSR) on psycholo......The prevalence of sleep disturbance is high among cancer patients, and the sleep problems tend to last for years after the end of treatment. As part of a large randomized controlled clinical trial (the MICA trial, NCT00990977) of the effect of mindfulness-based stress reduction (MBSR...

Rasch model analysis of the Depression, Anxiety and Stress Scales (DASS).

Science.gov (United States)

Shea, Tracey L; Tennant, Alan; Pallant, Julie F

2009-05-09

There is a growing awareness of the need for easily administered, psychometrically sound screening tools to identify individuals with elevated levels of psychological distress. Although support has been found for the psychometric properties of the Depression, Anxiety and Stress Scales (DASS) using classical test theory approaches it has not been subjected to Rasch analysis. The aim of this study was to use Rasch analysis to assess the psychometric properties of the DASS-21 scales, using two different administration modes. The DASS-21 was administered to 420 participants with half the sample responding to a web-based version and the other half completing a traditional pencil-and-paper version. Conformity of DASS-21 scales to a Rasch partial credit model was assessed using the RUMM2020 software. To achieve adequate model fit it was necessary to remove one item from each of the DASS-21 subscales. The reduced scales showed adequate internal consistency reliability, unidimensionality and freedom from differential item functioning for sex, age and mode of administration. Analysis of all DASS-21 items combined did not support its use as a measure of general psychological distress. A scale combining the anxiety and stress items showed satisfactory fit to the Rasch model after removal of three items. The results provide support for the measurement properties, internal consistency reliability, and unidimensionality of three slightly modified DASS-21 scales, across two different administration methods. The further use of Rasch analysis on the DASS-21 in larger and broader samples is recommended to confirm the findings of the current study.

Rasch model analysis of the Depression, Anxiety and Stress Scales (DASS)

Science.gov (United States)

Shea, Tracey L; Tennant, Alan; Pallant, Julie F

2009-01-01

Background There is a growing awareness of the need for easily administered, psychometrically sound screening tools to identify individuals with elevated levels of psychological distress. Although support has been found for the psychometric properties of the Depression, Anxiety and Stress Scales (DASS) using classical test theory approaches it has not been subjected to Rasch analysis. The aim of this study was to use Rasch analysis to assess the psychometric properties of the DASS-21 scales, using two different administration modes. Methods The DASS-21 was administered to 420 participants with half the sample responding to a web-based version and the other half completing a traditional pencil-and-paper version. Conformity of DASS-21 scales to a Rasch partial credit model was assessed using the RUMM2020 software. Results To achieve adequate model fit it was necessary to remove one item from each of the DASS-21 subscales. The reduced scales showed adequate internal consistency reliability, unidimensionality and freedom from differential item functioning for sex, age and mode of administration. Analysis of all DASS-21 items combined did not support its use as a measure of general psychological distress. A scale combining the anxiety and stress items showed satisfactory fit to the Rasch model after removal of three items. Conclusion The results provide support for the measurement properties, internal consistency reliability, and unidimensionality of three slightly modified DASS-21 scales, across two different administration methods. The further use of Rasch analysis on the DASS-21 in larger and broader samples is recommended to confirm the findings of the current study. PMID:19426512

Development of a Faith-Based Stress Management Intervention in a Rural African American Community.

Science.gov (United States)

Bryant, Keneshia; Moore, Todd; Willis, Nathaniel; Hadden, Kristie

2015-01-01

Faith-based mental health interventions developed and implemented using a community-based participatory research (CBPR) approach hold promise for reaching rural African Americans and addressing health disparities. To describe the development, challenges, and lessons learned from the Trinity Life Management, a faith-based stress management intervention in a rural African American faith community. The researchers used a CBPR approach by partnering with the African American faith community to develop a stress management intervention. Development strategies include working with key informants, focus groups, and a community advisory board (CAB). The community identified the key concepts that should be included in a stress management intervention. The faith-based "Trinity Life Management" stress management intervention was developed collaboratively by a CAB and an academic research team. The intervention includes stress management techniques that incorporate Biblical principles and information about the stress-distress-depression continuum.

Thermal stresses in the space shuttle orbiter: Analysis versus test

International Nuclear Information System (INIS)

Grooms, H.R.; Gibson, W.F. Jr.; Benson, P.L.

1984-01-01

Significant temperature differences occur between the internal structure and the outer skin of the Space Shuttle Orbiter as it returns from space. These temperature differences cause important thermal stresses. A finite element model containing thousands of degrees of freedom is used to predict these stresses. A ground test was performed to verify the prediction method. The analysis and test results compare favorably. (orig.)

Deduction and Analysis of the Interacting Stress Response Pathways of Metal/Radionuclide-reducing Bacteria

Energy Technology Data Exchange (ETDEWEB)

Zhou, Jizhong [University of Oklahoma; He, Zhili [University of Oklahoma

2010-02-28

Project Title: Deduction and Analysis of the Interacting Stress Response Pathways of Metal/Radionuclide-reducing Bacteria DOE Grant Number: DE-FG02-06ER64205 Principal Investigator: Jizhong (Joe) Zhou (University of Oklahoma) Key members: Zhili He, Aifen Zhou, Christopher Hemme, Joy Van Nostrand, Ye Deng, and Qichao Tu Collaborators: Terry Hazen, Judy Wall, Adam Arkin, Matthew Fields, Aindrila Mukhopadhyay, and David Stahl Summary Three major objectives have been conducted in the Zhou group at the University of Oklahoma (OU): (i) understanding of gene function, regulation, network and evolution of Desulfovibrio vugaris Hildenborough in response to environmental stresses, (ii) development of metagenomics technologies for microbial community analysis, and (iii) functional characterization of microbial communities with metagenomic approaches. In the past a few years, we characterized four CRP/FNR regulators, sequenced ancestor and evolved D. vulgaris strains, and functionally analyzed those mutated genes identified in salt-adapted strains. Also, a new version of GeoChip 4.0 has been developed, which also includes stress response genes (StressChip), and a random matrix theory-based conceptual framework for identifying functional molecular ecological networks has been developed with the high throughput functional gene array hybridization data as well as pyrosequencing data from 16S rRNA genes. In addition, GeoChip and sequencing technologies as well as network analysis approaches have been used to analyze microbial communities from different habitats. Those studies provide a comprehensive understanding of gene function, regulation, network, and evolution in D. vulgaris, and microbial community diversity, composition and structure as well as their linkages with environmental factors and ecosystem functioning, which has resulted in more than 60 publications.

Stress analysis of heated concrete using finite elements

International Nuclear Information System (INIS)

Majumdar, P.; Gupta, A.; Marchertas, A.

1994-01-01

Described is a finite element analysis of concrete, which is subjected to rapid heating. Using thermal mass transport calculation, the moisture content, temperature and pore pressure distribution over space and time is obtained first. From these effects, stress at various points of the concrete are computed using the finite element method. Contribution to the stress formulation comes from three components, namely the thermal expansion, pore pressure, and the shrinkage of concrete due to moisture loss (from dehydration). The material properties of concrete are assumed to be homogeneous, elastic, and cracking is not taken into consideration. (orig.)

Genome-wide expression analysis of rice ABC transporter family across spatio-temporal samples and in response to abiotic stresses.

Science.gov (United States)

Nguyen, Van Ngoc Tuyet; Moon, Sunok; Jung, Ki-Hong

2014-09-01

Although the super family of ATP-binding cassette (ABC) proteins plays key roles in the physiology and development of plants, the functions of members of this interesting family mostly remain to be clarified, especially in crop plants. Thus, systematic analysis of this family in rice (Oryza sativa), a major model crop plant, will be helpful in the design of effective strategies for functional analysis. Phylogenomic analysis that integrates anatomy and stress meta-profiling data based on a large collection of rice Affymetrix array data into the phylogenic context provides useful clues into the functions for each of the ABC transporter family members in rice. Using anatomy data, we identified 17 root-preferred and 16-shoot preferred genes at the vegetative stage, and 3 pollen, 2 embryo, 2 ovary, 2 endosperm, and 1 anther-preferred gene at the reproductive stage. The stress data revealed significant up-regulation or down-regulation of 47 genes under heavy metal treatment, 16 genes under nutrient deficient conditions, and 51 genes under abiotic stress conditions. Of these, we confirmed the differential expression patterns of 14 genes in root samples exposed to drought stress using quantitative real-time PCR. Network analysis using RiceNet suggests a functional gene network involving nine rice ABC transporters that are differentially regulated by drought stress in root, further enhancing the prediction of biological function. Our analysis provides a molecular basis for the study of diverse biological phenomena mediated by the ABC family in rice and will contribute to the enhancement of crop yield and stress tolerance. Copyright © 2014 Elsevier GmbH. All rights reserved.

Residual Stress Analysis for Engineering Applications by Means of Neutron Diffraction

International Nuclear Information System (INIS)

Gndupel-Herold, Thomas; Brand, Paul C.; Prask, Henry J.

1999-01-01

The economic and scientific importance of neutron diffraction residual stress analysis has led to an increasing number of suitable instruments worldwide. Recently, a dedicated state-of-the-art diffractometer has been installed at the National Institute of Standards and Technology reactor. It has been used for a variety of measurements on basic and engineering stress problems. Among the most prominent examples that have been investigated are residual stresses in rails, weldments, and plasma-sprayed coatings

Use of Variogram Parameters in Analysis of Hyperspectral Imaging Data Acquired from Dual-Stressed Crop Leaves

Directory of Open Access Journals (Sweden)

Christian Nansen

2012-01-01

Full Text Available A detailed introduction to variogram analysis of reflectance data is provided, and variogram parameters (nugget, sill, and range values were examined as possible indicators of abiotic (irrigation regime and biotic (spider mite infestation stressors. Reflectance data was acquired from 2 maize hybrids (Zea mays L. at multiple time points in 2 data sets (229 hyperspectral images, and data from 160 individual spectral bands in the spectrum from 405 to 907 nm were analyzed. Based on 480 analyses of variance (160 spectral bands × 3 variogram parameters, it was seen that most of the combinations of spectral bands and variogram parameters were unsuitable as stress indicators mainly because of significant difference between the 2 data sets. However, several combinations of spectral bands and variogram parameters (especially nugget values could be considered unique indicators of either abiotic or biotic stress. Furthermore, nugget values at 683 and 775 nm responded significantly to abiotic stress, and nugget values at 731 nm and range values at 715 nm responded significantly to biotic stress. Based on qualitative characterization of actual hyperspectral images, it was seen that even subtle changes in spatial patterns of reflectance values can elicit several-fold changes in variogram parameters despite non-significant changes in average and median reflectance values and in width of 95% confidence limits. Such scattered stress expression is in accordance with documented within-leaf variation in both mineral content and chlorophyll concentration and therefore supports the need for reflectance-based stress detection at a high spatial resolution (many hyperspectral reflectance profiles acquired from a single leaf and may be used to explain or characterize within-leaf foraging patterns of herbivorous arthropods.

Oxidative stress and the effect of parasites on a carotenoid-based ornament.

Science.gov (United States)

Mougeot, F; Martínez-Padilla, J; Blount, J D; Pérez-Rodríguez, L; Webster, L M I; Piertney, S B

2010-02-01

Oxidative stress, the physiological condition whereby the production of reactive oxygen and nitrogen species overwhelms the capacity of antioxidant defences, causes damage to key bio-molecules. It has been implicated in many diseases, and is proposed as a reliable currency in the trade-off between individual health and ornamentation. Whether oxidative stress mediates the expression of carotenoid-based signals, which are among the commonest signals of many birds, fish and reptiles, remains controversial. In the present study, we explored interactions between parasites, oxidative stress and the carotenoid-based ornamentation of red grouse Lagopus lagopus scoticus. We tested whether removing nematode parasites influenced both oxidative balance (levels of oxidative damage and circulating antioxidant defences) and carotenoid-based ornamentation. At the treatment group level, parasite purging enhanced the size and colouration of ornaments but did not significantly affect circulating carotenoids, antioxidant defences or oxidative damage. However, relative changes in these traits among individuals indicated that males with a greater number of parasites prior to treatment (parasite purging) showed a greater increase in the levels of circulating carotenoids and antioxidants, and a greater decrease in oxidative damage, than those with initially fewer parasites. At the individual level, a greater increase in carotenoid pigmentation was associated with a greater reduction in oxidative damage. Therefore, an individual's ability to express a carotenoid-based ornament appeared to be linked to its current oxidative balance and susceptibility to oxidative stress. Our experimental results suggest that oxidative stress can mediate the impact of parasites on carotenoid-based signals, and we discuss possible mechanisms linking carotenoid-based ornaments to oxidative stress.

Experimental stress analysis for determination of residual stresses and integrity monitoring of components and systems

International Nuclear Information System (INIS)

1993-01-01

For an analysis of the safety-related significance of residual stresses, mechanical, magnetic as well as ultrasonic and diffraction methods can be applied as testing methods. The results of an interlaboratory test concerning the experimental determination of residual stresses in a railway track are included. Further, questions are analyzed concerning the in-service inspections of components and systems with regard to their operational safety and life. Measurement methods are explained by examples from power plant engineering, nuclear power plant engineering, construction and traffic engineering as well as aeronautics. (DG) [de

Effects of stress on decisions under uncertainty: A meta-analysis.

Science.gov (United States)

Starcke, Katrin; Brand, Matthias

2016-09-01

[Correction Notice: An Erratum for this article was reported in Vol 142(9) of Psychological Bulletin (see record 2016-39486-001). It should have been reported that the inverted u-shaped relationship between cortisol stress responses and decision-making performance was only observed in female, but not in male participants as suggested by the study by van den Bos, Harteveld, and Stoop (2009). Corrected versions of the affected sentences are provided.] The purpose of the present meta-analysis was to quantify the effects that stress has on decisions made under uncertainty. We hypothesized that stress increases reward seeking and risk taking through alterations of dopamine firing rates and reduces executive control by hindering optimal prefrontal cortex functioning. In certain decision situations, increased reward seeking and risk taking is dysfunctional, whereas in others, this is not the case. We also assumed that the type of stressor plays a role. In addition, moderating variables are analyzed, such as the hormonal stress response, the time between stress onset and decisions, and the participants' age and gender. We included studies in the meta-analysis that investigated decision making after a laboratory stress-induction versus a control condition (k = 32 datasets, N = 1829 participants). A random-effects model revealed that overall, stress conditions lead to decisions that can be described as more disadvantageous, more reward seeking, and more risk taking than nonstress conditions (d = .17). In those situations in which increased reward seeking and risk taking is disadvantageous, stress had significant effects (d = .26), whereas in other situations, no effects were observed (d = .01). Effects were observed under processive stressors (d = .19), but not under systemic ones (d = .09). Moderation analyses did not reveal any significant results. We concluded that stress deteriorates overall decision-making performance through the mechanisms proposed. The effects differ

Prion-based memory of heat stress in yeast.

Science.gov (United States)

Chernova, Tatiana A; Chernoff, Yury O; Wilkinson, Keith D

2017-05-04

Amyloids and amyloid-based prions are self-perpetuating protein aggregates which can spread by converting a normal protein of the same sequence into a prion form. They are associated with diseases in humans and mammals, and control heritable traits in yeast and other fungi. Some amyloids are implicated in biologically beneficial processes. As prion formation generates reproducible memory of a conformational change, prions can be considered as molecular memory devices.  We have demonstrated that in yeast, stress-inducible cytoskeleton-associated protein Lsb2 forms a metastable prion in response to high temperature. This prion promotes conversion of other proteins into prions and can persist in a fraction of cells for a significant number of cell generations after stress, thus maintaining the memory of stress in a population of surviving cells. Acquisition of an amino acid substitution required for Lsb2 to form a prion coincides with acquisition of increased thermotolerance in the evolution of Saccharomyces yeast. Thus the ability to form an Lsb2 prion in response to stress coincides with yeast adaptation to growth at higher temperatures. These findings intimately connect prion formation to the cellular response to environmental stresses.

Stress analysis of fuelling machine magazine housing of PHWR

International Nuclear Information System (INIS)

Singh, R.K.; Mehra, V.K.; Charan, J.J.; Kakodkar, A.

1983-01-01

PWR has fuelling machines for on-line refuelling of the core. Magazine housing of this fuelling machine is a thick pressure vessel. It has a cylindrical vessel with flat head on one side and reservable flange closure on the other side. The vessel has many small and big openings. This paper describes the two sets of experiments conducted for its stress analysis. First set of experiment was conducted on a 1:5 photoelastic model which was stress frozen under load of internal pressure. The second set of experiment involved strain gauge measurements at some important locations of the magazine housing. The paper summarises results of the experiments. In conclusion comparison is made between the experimental results and the results of finite element analysis. (orig.)

Relative Quantitative Proteomic Analysis of Brucella abortus Reveals Metabolic Adaptation to Multiple Environmental Stresses

Directory of Open Access Journals (Sweden)

Xiaodong Zai

2017-11-01

Full Text Available Brucella spp. are facultative intracellular pathogens that cause chronic brucellosis in humans and animals. The virulence of Brucella primarily depends on its successful survival and replication in host cells. During invasion of the host tissue, Brucella is simultaneously subjected to a variety of harsh conditions, including nutrient limitation, low pH, antimicrobial defenses, and extreme levels of reactive oxygen species (ROS via the host immune response. This suggests that Brucella may be able to regulate its metabolic adaptation in response to the distinct stresses encountered during its intracellular infection of the host. An investigation into the differential proteome expression patterns of Brucella grown under the relevant stress conditions may contribute toward a better understanding of its pathogenesis and adaptive response. Here, we utilized a mass spectrometry-based label-free relative quantitative proteomics approach to investigate and compare global proteomic changes in B. abortus in response to eight different stress treatments. The 3 h short-term in vitro single-stress and multi-stress conditions mimicked the in vivo conditions of B. abortus under intracellular infection, with survival rates ranging from 3.17 to 73.17%. The proteomic analysis identified and quantified a total of 2,272 proteins and 74% of the theoretical proteome, thereby providing wide coverage of the B. abortus proteome. By including eight distinct growth conditions and comparing these with a control condition, we identified a total of 1,221 differentially expressed proteins (DEPs that were significantly changed under the stress treatments. Pathway analysis revealed that most of the proteins were involved in oxidative phosphorylation, ABC transporters, two-component systems, biosynthesis of secondary metabolites, the citrate cycle, thiamine metabolism, and nitrogen metabolism; constituting major response mechanisms toward the reconstruction of cellular

Nonlinear Heart Rate Variability features for real-life stress detection. Case study: students under stress due to university examination.

Science.gov (United States)

Melillo, Paolo; Bracale, Marcello; Pecchia, Leandro

2011-11-07

This study investigates the variations of Heart Rate Variability (HRV) due to a real-life stressor and proposes a classifier based on nonlinear features of HRV for automatic stress detection. 42 students volunteered to participate to the study about HRV and stress. For each student, two recordings were performed: one during an on-going university examination, assumed as a real-life stressor, and one after holidays. Nonlinear analysis of HRV was performed by using Poincaré Plot, Approximate Entropy, Correlation dimension, Detrended Fluctuation Analysis, Recurrence Plot. For statistical comparison, we adopted the Wilcoxon Signed Rank test and for development of a classifier we adopted the Linear Discriminant Analysis (LDA). Almost all HRV features measuring heart rate complexity were significantly decreased in the stress session. LDA generated a simple classifier based on the two Poincaré Plot parameters and Approximate Entropy, which enables stress detection with a total classification accuracy, a sensitivity and a specificity rate of 90%, 86%, and 95% respectively. The results of the current study suggest that nonlinear HRV analysis using short term ECG recording could be effective in automatically detecting real-life stress condition, such as a university examination.

Multiaxial stress analysis taking account of penetration depth of x-rays, 3

International Nuclear Information System (INIS)

Yoshioka, Yasuo; Sasaki, Toshihiko; Kuramoto, Makoto.

1985-01-01

In the past X-ray stress analysis in which the effect of stress gradients was taken into account within the penetration depth of X-rays, three assumptions have been made; 1) the stress gradient is linear in respect to the depth from the specimen surface, 2) the penetration depth of X-ray is a function of Sin 2 PSI and 3) the strain measured by X-rays corresponds to the weighted average strain on the intensity of the diffracted X-rays. A problem, however, still remains on the assumption of the X-ray penetration depth. We sometimes observed noticiable errors in the stage of the numerical simulation and these errors depend on the combination of stress components in a stress tensor. In the present paper, we proposed a new X-ray multiaxial stress analysis without using the assumption of the X-ray penetration depth. This analysis is also applicable to both the iso-inclination method ( OHM -goniometer) and the side inclination method (PSI-goniometer). The weighted average strain by X-rays, 1 >(phi), is expressed as a 4th degree function of cosPSI for iso-inclination method and 3rd degree for side inclination method. By rearranging this function as a sum of average strain, ( 1 >(0 0 )+ 1 >(90 0 )), and difference of average strain, ( 1 >(0 0 )- 1 >(90 0 )), we can solve the stress components with sufficient accuracy by a least squares method. The validity of this method was proved through numerical simulations and experiments. (author)

Comparative proteomic analysis in Miscanthus sinensis exposed to antimony stress

International Nuclear Information System (INIS)

Xue, Liang; Ren, Huadong; Li, Sheng; Gao, Ming; Shi, Shengqing; Chang, Ermei; Wei, Yuan; Yao, Xiaohua; Jiang, Zeping; Liu, Jianfeng

2015-01-01

To explore the molecular basis of Sb tolerance mechanism in plant, a comparative proteomic analysis of both roots and leaves in Miscanthus sinensis has been conducted in combination with physiological and biochemical analyses. M. sinensis seedlings were exposed to different doses of Sb, and both roots and leaves were collected after 3 days of treatment. Two-dimensional gel electrophoresis (2-DE) and image analyses found that 29 protein spots showed 1.5-fold change in abundance in leaves and 19 spots in roots, of which 31 were identified by MALDI-TOF-MS and MALDI-TOF-TOF-MS. Proteins involved in antioxidant defense and stress response generally increased their expression all over the Sb treatments. In addition, proteins relative to transcription, signal transduction, energy metabolism and cell division and cell structure showed a variable expression pattern over Sb concentrations. Overall these findings provide new insights into the probable survival mechanisms by which M. sinensis could be adapting to Sb phytotoxicity. - Highlights: • Proteomics in Miscanthus sinensis leaves and roots exposed to Sb stress were studied. • There were 31 spots that were identified by mass spectrometry. • Most of these proteins were involved in antioxidant defense and stress response. • Our findings provide new insights into the tolerant mechanisms to Sb stress. - Miscanthus sinensis proteomic analysis under Sb stress reveals probable molecular mechanisms on Sb detoxification

Computer-based versus in-person interventions for preventing and reducing stress in workers.

Science.gov (United States)

Kuster, Anootnara Talkul; Dalsbø, Therese K; Luong Thanh, Bao Yen; Agarwal, Arnav; Durand-Moreau, Quentin V; Kirkehei, Ingvild

2017-08-30

Chronic exposure to stress has been linked to several negative physiological and psychological health outcomes. Among employees, stress and its associated effects can also result in productivity losses and higher healthcare costs. In-person (face-to-face) and computer-based (web- and mobile-based) stress management interventions have been shown to be effective in reducing stress in employees compared to no intervention. However, it is unclear if one form of intervention delivery is more effective than the other. It is conceivable that computer-based interventions are more accessible, convenient, and cost-effective. To compare the effects of computer-based interventions versus in-person interventions for preventing and reducing stress in workers. We searched CENTRAL, MEDLINE, PubMed, Embase, PsycINFO, NIOSHTIC, NIOSHTIC-2, HSELINE, CISDOC, and two trials registers up to February 2017. We included randomised controlled studies that compared the effectiveness of a computer-based stress management intervention (using any technique) with a face-to-face intervention that had the same content. We included studies that measured stress or burnout as an outcome, and used workers from any occupation as participants. Three authors independently screened and selected 75 unique studies for full-text review from 3431 unique reports identified from the search. We excluded 73 studies based on full-text assessment. We included two studies. Two review authors independently extracted stress outcome data from the two included studies. We contacted study authors to gather additional data. We used standardised mean differences (SMDs) with 95% confidence intervals (CIs) to report study results. We did not perform meta-analyses due to variability in the primary outcome and considerable statistical heterogeneity. We used the GRADE approach to rate the quality of the evidence. Two studies met the inclusion criteria, including a total of 159 participants in the included arms of the studies

Cantilever-based sensing: the origin of surface stress and optimization strategies

International Nuclear Information System (INIS)

Godin, Michel; Tabard-Cossa, Vincent; Miyahara, Yoichi; Grutter, Peter; Monga, Tanya; Bruce Lennox, R; Williams, P J; Beaulieu, L Y

2010-01-01

Many interactions drive the adsorption of molecules on surfaces, all of which can result in a measurable change in surface stress. This article compares the contributions of various possible interactions to the overall induced surface stress for cantilever-based sensing applications. The surface stress resulting from adsorption-induced changes in the electronic density of the underlying surface is up to 2-4 orders of magnitude larger than that resulting from intermolecular electrostatic or Lennard-Jones interactions. We reveal that the surface stress associated with the formation of high quality alkanethiol self-assembled monolayers on gold surfaces is independent of the molecular chain length, supporting our theoretical findings. This provides a foundation for the development of new strategies for increasing the sensitivity of cantilever-based sensors for various applications.