Thinner eggshells of dipper (Cinclus cinclus) eggs from an acidified area compared to a non-acidified area in Norway

Energy Technology Data Exchange (ETDEWEB)

Nyboe, S.; Staurnes, M.; Jerstad, K. [Norwegian University of Science and Technology, Dragvoll (Norway). Dept. of Zoology

1997-01-01

Eggs of dippers Cinclus cinclus from a chronically acidified area in Southern Norway were compared with eggs from a non-acidified area in Central Norway. There were no differences in egg size, as measured by volume, weight, length and calculated surface area, between the two areas. Eggshells were 7.0% lighter and 6.1% thinner, as measured by the Ratcliffe index and 7.0% as measured by the eggshell index (shell weight/surface area) in Southern Norway than in Central Norway. The Ratcliffe and eggshell indices were highly correlated. Scanning electron micrography showed that the palisade layer of eggshells of eggs from the acidified area was 10.7% thinner than that of eggshells of eggs from the non-acidified area. Eggshell vapour permeability was not significantly influenced by area. Since the moderately lower thickness in Southern Norway was not accompanied by higher vapour permeability, this indicates that the reduced eggshell thickness did not cause desiccation of dipper eggs in the acidified area. The possibility of underestimating the environmental effects of acidification on dippers is discussed. 42 refs.,2 figs., 4 tabs.

U-Th Burial Dates on Ostrich Eggshell

Science.gov (United States)

Sharp, W. D.; Fylstra, N. D.; Tryon, C. A.; Faith, J. T.; Peppe, D. J.

2015-12-01

Obtaining precise and accurate dates at archaeological sites beyond the range of radiocarbon dating is challenging but essential for understanding human origins. Eggshells of ratites (large flightless birds including ostrich, emu and others) are common in many archaeological sequences in Africa, Australia and elsewhere. Ancient eggshells are geochemically suitable for the U-Th technique (1), which has about ten times the range of radiocarbon dating (>500 rather than 50 ka), making eggshells attractive dating targets. Moreover, C and N isotopic studies of eggshell provide insights into paleovegetation and paleoprecipitation central to assessing past human-environment interactions (2,3). But until now, U-Th dates on ratite eggshell have not accounted for the secondary origin of essentially all of their U. We report a novel approach to U-Th dating of eggshell that explicitly accounts for secondary U uptake that begins with burial. Using ostrich eggshell (OES) from Pleistocene-Holocene east African sites, we have measured U and 232Th concentration profiles across OES by laser ablation ICP-MS. U commonly peaks at 10s to 100s of ppb and varies 10-fold or more across the ~2 mm thickness of OES, with gradients modulated by the layered structure of the eggshell. Common Th is high near the shell surfaces, but low in the middle "pallisade" layer of OES, making it optimal for U-Th dating. We determine U-Th ages along the U concentration gradient by solution ICP-MS analyses of two or more fractions of the pallisade layer. We then estimate OES burial dates using a simple model for diffusive uptake of uranium. Comparing such "U-Th burial dates" with radiocarbon dates for OES calcite from the same shells, we find good agreement in 7 out of 9 cases, consistent with rapid burial and confirming the accuracy of the approach. The remaining 2 eggshells have anomalous patterns of apparent ages that reveal they are unsuitable for U-Th dating, thereby providing reliability criteria innate

Regional and interspecific variation in Sr, Ca, and Sr/Ca ratios in avian eggshells from the USA.

Science.gov (United States)

Mora, Miguel A; Brattin, Bryan; Baxter, Catherine; Rivers, James W

2011-08-01

To examine regional variation in strontium (Sr), which at high concentrations may reduce eggshell quality, increase egg breakage and reproductive failure, we analyzed Sr, and calcium (Ca) concentrations and Sr/Ca ratios in eggshells from 20 avian species from California, Texas, Idaho, Kansas, and Michigan. In addition, we included data previously reported from Arizona to expand the regional comparisons and to better establish patterns of Sr, and Sr/Ca ratios in bird species across the United States. We found Sr concentrations varied significantly among regions, among species, and among foraging guilds; this variability is strongly influenced by the Sr/Ca ratios in surface water from locations close to the region where the eggshells were collected. Sr concentrations and Sr/Ca ratios were significantly higher in bird eggshells from the Volta wildlife region in the San Joaquin Valley, California and in various locales from Arizona. Sr concentrations and Sr/Ca ratios in bird eggshells from other locations in the USA were lower than those detected in these two regions. Among foraging guilds, invertivores had the highest Sr concentrations and Sr/Ca ratios and carnivores had the lowest. In general, the Sr/Ca ratio increased strongly with increasing Sr concentrations (R(2) = 0.99, P eggshells suggesting that these values could be determined from Sr/Ca ratios in water. Eggshell thickness was poorly correlated with Sr (R(2) = 0.03) but had a significant and positive correlation with Ca and was more properly correlated by a quadratic equation (R(2) = 0.50, Thickness = 2.13 - 0.02Ca - 3.07 * 10(-5)Ca(2)). Our study provides further evidence that Sr accumulates significantly in the avian eggshell, in some regions at concentrations which could be of concern for potential negative effects on reproduction. We suggest that when assessing the effects of metals on avian reproduction in regions with high Sr deposits in rock and soil, Sr concentrations in the eggshell also should be

Potential ecotoxicological significance of elevated concentrations of strontium in eggshells of passerine birds

Science.gov (United States)

Mora, Miguel A.; Taylor, Robert J.; Brattin, Bryan L.

2007-01-01

We investigated the occurrence and potential ecotoxicological significance of elevated concentrations of strontium (Sr) in eggshells of nine passerine birds from four regions in Arizona. Concentrations of Sr in eggshells ranged from 70 to 1360 µg g−1 dry weight (overall mean  =  684 ± 345 SD µg g−1 dw) for the four regions. 23% of the eggshells had Sr concentrations greater than 1000 µg g−1 dw. To our knowledge, these are among the highest levels of Sr that have been reported in bird eggshells in North America. Of the nine species, Brown-headed Cowbirds (Molothrus ater) had the greatest concentrations of Sr. There was a significant positive correlation between Sr and calcium (Ca), and between barium (Ba) and Ca. Ca, Sr, and Ba interact with each other and can exert similar chemical and pharmacological effects. Mean (n ≥ 3) eggshell∶egg ratios for Sr varied with species and ranged from 6.1∶1 to 40.2∶1; ratios for individual eggs reached 92.7∶1. Mean Sr/Ca values ranged from 1.3 × 10−3 to 3.0 × 10−3 and mean eggshell thickness ranged from 83 ± 6 to 120 ± 9 µm for all species. Eggshell thickness was not significantly correlated with Sr for any species but tended to increase with Sr concentrations. We postulate that high concentrations of Sr in the shell could affect later-stage embryos by possible interference with Ca metabolism and bone growth, resulting in reduced hatching success and potential minor beak deformities.

Eggshell thinning and residues in mallards on year after DDE exposure

Science.gov (United States)

Haegele, M.A.; Hudson, R.H.

1974-01-01

A group of 16 mallard hens (Anas platyrhynchos), that had been given feed containing 40 ppm ofp,p'-DDE for 96 days, laid eggs with shells averaging about 15%?20% thinner than those of ten control birds during and up to 42 days after treatment. In eight of the treated birds killed at that time, whole-body DDE residues averaged 33.1 ppm (wet weight). The other eight treated birds and ten controls were kept through the winter with no additional DDE exposure and penned separately five days for individual egg collection about three weeks after laying began in spring. At that time (nearly 11 months after DDE feeding had stopped), the treated birds laid eggs with shells averaging 7.4% thinner than control eggshells (significant at P<0.05) and their whole-body DDE residues averaged 9.6 ppm (wet weight). Variations in eggshell thickness and DDE residues were considerable among treated birds. However, regression analysis showed moderate negative correlations (r=?0.51 to ?0.62) between eggshell thickness and DDE residues in whole bodies and eggs, and strong positive correlations (r=0.73 and 0.91) between DDE residues in whole bodies and in eggs.

Eggshells as an index of aedine mosquito production. 1: Distribution, movement and sampling of Aedes taeniorhynchus eggshells.

Science.gov (United States)

Ritchie, S A; Addison, D S; van Essen, F

1992-03-01

The distribution of Aedes taeniorhynchus eggshells in Florida mangrove basin forests was determined and used to design a sampling plan. Eggshells were found in 10/11 sites (91%), with a mean +/- SE density of 1.45 +/- 0.75/cc; density did not change significantly year to year. Highest densities were located on the sloping banks of hummocks, ponds and potholes. Eggshells were less clumped in distribution than eggs and larvae and thus required a smaller sample size for a given precision level. While eggshells were flushed from compact soil that was subject to runoff during heavy rain, mangrove peat, the dominant soil of eggshell-bearing sites, was less dense and had little runoff or eggshell flushing. We suggest that eggshell surveys could be used to identify Ae. taeniorhynchus oviposition sites and oviposition patterns.

Compressive strength of thick composite panels

DEFF Research Database (Denmark)

Branner, Kim; Berring, Peter

2011-01-01

The aim of this study is to investigate how much the compressive strength of thick composite panels is reduced due to delaminations and to investigate under which conditions a delamination will grow. Understanding of this is essential in order to move forward the design limits used in the structu......The aim of this study is to investigate how much the compressive strength of thick composite panels is reduced due to delaminations and to investigate under which conditions a delamination will grow. Understanding of this is essential in order to move forward the design limits used...

Biomechanical evidence suggests extensive eggshell thinning during incubation in the Sanagasta titanosaur dinosaurs

Directory of Open Access Journals (Sweden)

E. Martín Hechenleitner

2018-06-01

Full Text Available The reproduction of titanosaur dinosaurs is still a complex and debated topic. Their Late Cretaceous nesting sites are distributed worldwide and their eggs display substantial morphological variations according to the parent species. In contrast to the typical 1.3–2.0 mm thick shells common to eggs of most titanosaur species (e.g., those that nested in Auca Mahuevo, Tama, Toteşti or Boseong, the Cretaceous Sanagasta eggs of Argentina display an unusual shell thickness of up to 7.9 mm. Their oviposition was synchronous with a palaeogeothermal process, leading to the hypothesis that their extra thick eggshell was an adaptation to this particular nesting environment. Although this hypothesis has already been supported indirectly through several investigations, the mechanical implications of developing such thick shells and how this might have affected the success of hatching remains untested. Finite element analyses estimate that the breaking point of the thick-shelled Sanagasta eggs is 14–45 times higher than for other smaller and equally sized titanosaur eggs. The considerable energetic disadvantage for piping through these thick eggshells suggests that their dissolution during incubation would have been paramount for a successful hatching.

Effect of loading rate on hen´s eggshell mechanics

Czech Academy of Sciences Publication Activity Database

Trnka, Jan; Buchar, J.; Severa, L.; Nedomová, Š.; Stoklasová, Pavla

2012-01-01

Roč. 1, č. 4 (2012), s. 1-5 ISSN 1927-0887 Institutional research plan: CEZ:AV0Z20760514 Keywords : eggshell * strength * elasticity * numerical simulation Subject RIV: GM - Food Processing http://www.ccsenet.org/journal/index.php/jfr/article/view/19064

Mechanical Properties of Composite Waste Material Based Styrofoam, Baggase and Eggshell Powder for Application of Drone Frames

Science.gov (United States)

Perdana, Mastariyanto; Prastiawan; Hadi, Syafrul

2017-12-01

The garbage issue becomes a very serious problem at the moment. Much research has been done to make waste into useful materials. One of the utilization of waste is as the basic material of composite material that can be applied in the field of engineering. Some of the wastes generated are styrofoam, bagasse and eggshell. Styrofoam, bagasse and eggshell can be applied to a composite material. Styrofoam serves as a composite binder material while the bagasse and eggshells serve as a reinforcement. Volume fraction between styrofoam, bagasse and eggshell are 80%:10%:10%, 70%:15%:15%, 60%:20%:20%, and 50%:25%:25%. The aims of research are determine the mechanical properties of composite material based waste materials from styrofoam, bagasse and eggshell. Mechanical properties tested in this study are bending strength and toughness of composite materials. The results showed bending strength of composite for each volume fraction of 80%:10%:10%, 70%:15%:15%, 60%:20%:20%, and 50%:25%:25% are 5.07 MPa, 8.45 MPa, 8.68 MPa, and 11.01 MPa, respectively. Toughness of composite materials for each volume fraction of 80%:10%:10%, 70%:15%:15%, 60%:20%:20%, and 50%:25%:25% are 0.33 J/mm2, 0.42 J/mm2, 0.75 J/mm2, and 0.75 J/mm2, respectively. Composite materials based on waste materials from styrofoam, bagasse and eggshell can be used as an alternative material for drone frames.

Fossil avian eggshell preserves ancient DNA

DEFF Research Database (Denmark)

Oskam, Charlotte L; Haile, James Seymour; McLay, Emma

2010-01-01

Owing to exceptional biomolecule preservation, fossil avian eggshell has been used extensively in geochronology and palaeodietary studies. Here, we show, to our knowledge, for the first time that fossil eggshell is a previously unrecognized source of ancient DNA (aDNA). We describe the successful...... isolation and amplification of DNA from fossil eggshell up to 19 ka old. aDNA was successfully characterized from eggshell obtained from New Zealand (extinct moa and ducks), Madagascar (extinct elephant birds) and Australia (emu and owl). Our data demonstrate excellent preservation of the nucleic acids......, evidenced by retrieval of both mitochondrial and nuclear DNA from many of the samples. Using confocal microscopy and quantitative PCR, this study critically evaluates approaches to maximize DNA recovery from powdered eggshell. Our quantitative PCR experiments also demonstrate that moa eggshell has...

Eggshells as an index of aedine mosquito production. 2: Relationship of Aedes taeniorhynchus eggshell density to larval production.

Science.gov (United States)

Addison, D S; Ritchie, S A; Webber, L A; Van Essen, F

1992-03-01

To test if eggshell density could be used as an index of aedine mosquito production, we compared eggshell density with the larval production of Aedes taeniorhynchus in Florida mangrove basin forests. Quantitative (n = 7) and categorical (n = 34) estimates of annual larval production were regressed against the number of eggshells per cc of soil. Significant regressions were obtained in both instances. Larval production was concentrated in zones with the highest eggshell density. We suggest that eggshell density and distribution can be used to identify oviposition sites and the sequence of larval appearance.

The cuticle modulates ultraviolet reflectance of avian eggshells

Directory of Open Access Journals (Sweden)

Daphne C. Fecheyr-Lippens

2015-07-01

Full Text Available Avian eggshells are variedly coloured, yet only two pigments, biliverdin and protoporphyrin IX, are known to contribute to the dramatic diversity of their colours. By contrast, the contributions of structural or other chemical components of the eggshell are poorly understood. For example, unpigmented eggshells, which appear white to the human eye, vary in their ultraviolet (UV reflectance, which may be detectable by birds. We investigated the proximate mechanisms for the variation in UV-reflectance of unpigmented bird eggshells using spectrophotometry, electron microscopy, chemical analyses, and experimental manipulations. We specifically tested how UV-reflectance is affected by the eggshell cuticle, the outermost layer of most avian eggshells. The chemical dissolution of the outer eggshell layers, including the cuticle, increased UV-reflectance for only eggshells that contained a cuticle. Our findings demonstrate that the outer eggshell layers, including the cuticle, absorb UV-light, probably because they contain higher levels of organic components and other chemicals, such as calcium phosphates, compared to the predominantly calcite-based eggshell matrix. These data highlight the need to examine factors other than the known pigments in studies of avian eggshell colour.

Electromechanical-conductive natural rubber doped eggshell and ...

African Journals Online (AJOL)

The main composition of eggshells is calcium carbonate (CaCO3) of high purity more than 96.35 wt% whereas the main composition of eggshell membrane is fibrous protein in terms of collagen. The best condition is addition of eggshell 40 phr (formula 3) and eggshell membrane 20 phr (formula 5) to obtain the highest ...

Large-scale geographical variation in eggshell metal and calcium content in a passerine bird (Ficedula hypoleuca).

Science.gov (United States)

Ruuskanen, Suvi; Laaksonen, Toni; Morales, Judith; Moreno, Juan; Mateo, Rafael; Belskii, Eugen; Bushuev, Andrey; Järvinen, Antero; Kerimov, Anvar; Krams, Indrikis; Morosinotto, Chiara; Mänd, Raivo; Orell, Markku; Qvarnström, Anna; Slate, Fred; Tilgar, Vallo; Visser, Marcel E; Winkel, Wolfgang; Zang, Herwig; Eeva, Tapio

2014-03-01

Birds have been used as bioindicators of pollution, such as toxic metals. Levels of pollutants in eggs are especially interesting, as developing birds are more sensitive to detrimental effects of pollutants than adults. Only very few studies have monitored intraspecific, large-scale variation in metal pollution across a species' breeding range. We studied large-scale geographic variation in metal levels in the eggs of a small passerine, the pied flycatcher (Ficedula hypoleuca), sampled from 15 populations across Europe. We measured 10 eggshell elements (As, Cd, Cr, Cu, Ni, Pb, Zn, Se, Sr, and Ca) and several shell characteristics (mass, thickness, porosity, and color). We found significant variation among populations in eggshell metal levels for all metals except copper. Eggshell lead, zinc, and chromium levels decreased from central Europe to the north, in line with the gradient in pollution levels over Europe, thus suggesting that eggshell can be used as an indicator of pollution levels. Eggshell lead levels were also correlated with soil lead levels and pH. Most of the metals were not correlated with eggshell characteristics, with the exception of shell mass, or with breeding success, which may suggest that birds can cope well with the current background exposure levels across Europe.

Dietary calcium deficiency in laying ducks impairs eggshell quality by suppressing shell biomineralization.

Science.gov (United States)

Chen, Wei; Zhao, Fei; Tian, Zhi Mei; Zhang, Han Xing; Ruan, Dong; Li, Yan; Wang, Shuang; Zheng, Chun Tian; Lin, Ying Cai

2015-10-01

The objective of this study was to determine the effects of dietary calcium deficiency on the process of shell formation. Four hundred and fifty female ducks (Anas platyrhynchos) at 22 weeks were randomly assigned to three groups. Ducks were fed one of two calcium-deficient diets (containing 1.8% or 0.38% calcium, respectively) or a calcium-adequate control diet (containing 3.6% calcium) for 67 days (depletion period) and then all ducks were fed a calcium-adequate diet for an additional 67 days (repletion period). Compared with the calcium-adequate control, the average shell thickness, egg shell weight, breaking strength, mammillae density and mammillary knob thickness of shell from ducks that consumed the diet with 0.38% calcium were significantly decreased (Pducks fed 0.38% calcium but not 1.8% calcium. Plasma estradiol concentration was decreased by both of the calcium-deficient diets (Pstudy suggest that dietary calcium deficiency negatively affects eggshell quality and microarchitecture, probably by suppressing shell biomineralization. © 2015. Published by The Company of Biologists Ltd.

Biodegradation of thermoplastic starch/eggshell powder composites.

Science.gov (United States)

Bootklad, Munlika; Kaewtatip, Kaewta

2013-09-12

Thermoplastic starch (TPS) was prepared using compression molding and chicken eggshell was used as a filler. The effect of the eggshell powder (EP) on the properties of TPS was compared with the effect of commercial calcium carbonate (CC). The organic compound on the surface of the eggshell powder acted as a coupling agent that resulted in a strong adhesion between the eggshell powder and the TPS matrix, as confirmed by SEM micrographs. The biodegradation was determined by the soil burial test. The TPS/EP composites were more rapidly degraded than the TPS/CC composites. In addition, the eggshell powder improved the water resistance and thermal stability of the TPS. Copyright © 2013 Elsevier Ltd. All rights reserved.

Eggshell thickness in mourning dove populations

Science.gov (United States)

Kreitzer, J.F.

1971-01-01

Eggs (n = 452) of the mourning dove (Zenaidura macroura) were collected from 9 states in 1969 and 11 states in 1970, and shell thickness was compared with that of eggs (n = 97) collected from 24 states during the years 1861 to 1935. Mean shell thickness did not differ significantly in the test groups.

Chicken eggshell as suitable calcium source at home.

Science.gov (United States)

Brun, Lucas R; Lupo, Maela; Delorenzi, Damián A; Di Loreto, Verónica E; Rigalli, Alfredo

2013-09-01

Taken into consideration that the deficiency of calcium (Ca) in the diet is a common problem, the aim of this work was to study the chicken eggshell as Ca source at home. It was evaluated: (1) different mechanisms to process eggshells and find an easy way to determine the required amount of Ca at home and; (2) the flavor and the texture for eggshell fortified food. Chemical and mechanical methods of eggshell processing were evaluated. Changes in flavor and texture were evaluated in volunteers coordinated by a professional chef. A single eggshell contains 2.07 ± 0.18 g of Ca; therefore half an eggshell could provide the amount of Ca needed by adult human beings per day. The best way to use chicken eggshell as Ca dietary supplement is powdered to add to bread, pizza or spaghetti as there were small changes in texture and no changes in flavor.

Micro-CT scan reveals an unexpected high-volume and interconnected pore network in a Cretaceous Sanagasta dinosaur eggshell.

Science.gov (United States)

Hechenleitner, E Martín; Grellet-Tinner, Gerald; Foley, Matthew; Fiorelli, Lucas E; Thompson, Michael B

2016-03-01

The Cretaceous Sanagasta neosauropod nesting site (La Rioja, Argentina) was the first confirmed instance of extinct dinosaurs using geothermal-generated heat to incubate their eggs. The nesting strategy and hydrothermal activities at this site led to the conclusion that the surprisingly 7 mm thick-shelled eggs were adapted to harsh hydrothermal microenvironments. We used micro-CT scans in this study to obtain the first three-dimensional microcharacterization of these eggshells. Micro-CT-based analyses provide a robust assessment of gas conductance in fossil dinosaur eggshells with complex pore canal systems, allowing calculation, for the first time, of the shell conductance through its thickness. This novel approach suggests that the shell conductance could have risen during incubation to seven times more than previously estimated as the eggshell erodes. In addition, micro-CT observations reveal that the constant widening and branching of pore canals form a complex funnel-like pore canal system. Furthermore, the high density of pore canals and the presence of a lateral canal network in the shell reduce the risks of pore obstruction during the extended incubation of these eggs in a relatively highly humid and muddy nesting environment. © 2016 The Author(s).

Nesting environment may drive variation in eggshell structure and egg characteristics in the Testudinata.

Science.gov (United States)

Deeming, D Charles

2018-05-14

Testudines exhibit considerable variation in the degree of eggshell calcification, which affects eggshell conductance, water physiology of the embryos, and calcium metabolism of embryos. However, the underlying reason for different shell types has not been explored. Phylogenetically controlled analyses examined relationships between egg size, shell mass, and clutch size in ∼200 turtle species from a range of body sizes and assigned by family as laying either rigid- or pliable-shelled eggs. Shell type affected egg breadth relative to pelvic dimensions, egg mass, and relative shell mass but did not affect size, mass, or total shell mass of the clutch. These results suggest that calcium availability may be a function of body size and the type of shell may reflect in part the interplay between clutch size and egg size. It was further concluded that the eggshell probably evolved as a means of physical protection. Differences in shell calcification may not primarily reflect reproductive parameters but rather correlate with the acidity of a species' nesting environment. Low pH environments may have thicker calcareous layer to counteract the erosion caused by the soil and maintain the integrity of the physical barrier. Limited calcium availability may constrain clutch size. More neutral nesting substrates expose eggshells to less erosion so calcification per egg can be reduced and this allows larger clutch sizes. This pattern is also reflected in thick, calcified crocodilian eggs. Further research is needed to test whether eggshell calcification in the testudines correlates with nest pH in order to verify this relationship. © 2018 Wiley Periodicals, Inc.

Brood parasite and host eggshells undergo similar levels of decalcification during embryonic development

Czech Academy of Sciences Publication Activity Database

Igic, B.; Hauber, M. E.; Moskát, C.; Grim, T.; Shawkey, M. D.; Procházka, Petr; Honza, Marcel

2017-01-01

Roč. 301, č. 3 (2017), s. 165-173 ISSN 0952-8369 R&D Projects: GA ČR(CZ) GAP506/12/2404 Institutional support: RVO:68081766 Keywords : Acrocephalus arundinaceus * brood parasitism * Cuculus canorus * decalcification * eggshell thickness * embryonic development * common cuckoo * scanning electron microscopy Subject RIV: EG - Zoology OBOR OECD: Zoology Impact factor: 2.186, year: 2016

Comparative proteomics of matrix fractions between pimpled and normal chicken eggshells.

Science.gov (United States)

Liu, Zhangguo; Song, Lingzi; Lu, Lizhi; Zhang, Xianfu; Zhang, Fuming; Wang, Kehua; Linhardt, Robert J

2017-09-07

Eggshell matrix can be dissociated into three matrix fractions: acid-insoluble matrix (M1), water-insoluble matrix (M2) and acid-water facultative-soluble matrix (M3). Matrix fractions from pimpled and normal eggshells were compared using label-free proteomic method to understand the differences among three matrix fractions and the proteins involved with eggshell quality. A total of 738 and 600 proteins were identified in the pimpled and normal calcified eggshells, respectively. Both eggshells showed a combined proteomic inventory of 769 proteins. In the same type of eggshell, a high similarity was present in the proteomes of three matrix fractions. These triply overlapped common proteins formed the predominant contributor to proteomic abundance in the matrix fractions. In each matrix fraction and between both eggshell models, normal and pimpled eggshells, a majority of the proteomes of the fractions were commonly observed. Forty-two common major proteins (iBAQ-derived abundance ≥0.095% of proteomic abundance) were identified throughout the three matrix fractions and these proteins might act as backbone constituents in chicken eggshell matrix. Finally, using 1.75-fold as up-regulated and using 0.57-fold as down-regulated cutoff values, twenty-five differential major proteins were screened and they all negatively influence and none showed any effect on eggshell quality. Overall, we uncovered the characteristics of proteomics of three eggshell matrix fractions and identified candidate proteins influencing eggshell quality. The next research on differential proteins will uncover the potential mechanisms underlying how proteins affect eggshell quality. It was reported that the proteins in an eggshell can be divided into insoluble and soluble proteins. The insoluble proteins are thought to be an inter-mineral matrix and acts as a structural framework, while the soluble proteins are thought as intra-mineral matrix that are embedded within the crystal during

Eggshell spottiness reflects maternally transferred antibodies in blue tits.

Directory of Open Access Journals (Sweden)

Marie-Jeanne Holveck

Full Text Available Blue-green and brown-spotted eggshells in birds have been proposed as sexual signals of female physiological condition and egg quality, reflecting maternal investment in the egg. Testing this hypothesis requires linking eggshell coloration to egg content, which is lacking for brown protoporphyrin-based pigmentation. As protoporphyrins can induce oxidative stress, and a large amount in eggshells should indicate either high female and egg quality if it reflects the female's high oxidative tolerance, or conversely poor quality if it reflects female physiological stress. Different studies supported either predictions but are difficult to compare given the methodological differences in eggshell-spottiness measurements. Using the blue tit Cyanistes caeruleus as a model species, we aimed at disentangling both predictions in testing if brown-spotted eggshell could reflect the quality of maternal investment in antibodies and carotenoids in the egg, and at improving between-study comparisons in correlating several common measurements of eggshell coloration (spectral and digital measures, spotted surface, pigmentation indices. We found that these color variables were weakly correlated highlighting the need for comparable quantitative measurements between studies and for multivariate regressions incorporating several eggshell-color characteristics. When evaluating the potential signaling function of brown-spotted eggshells, we thus searched for the brown eggshell-color variables that best predicted the maternal transfer of antibodies and carotenoids to egg yolks. We also tested the effects of several parental traits and breeding parameters potentially affecting this transfer. While eggshell coloration did not relate to yolk carotenoids, the eggs with larger and less evenly-distributed spots had higher antibody concentrations, suggesting that both the quantity and distribution of brown pigments reflected the transfer of maternal immune compounds in egg yolks

Microwave Irradiation of Nanohydroxyapatite from Chicken Eggshells and Duck Eggshells

Directory of Open Access Journals (Sweden)

Nor Adzliana Sajahan

2014-01-01

Full Text Available Due to similarity in composition to the mineral component of bones and human hard tissues, hydroxyapatite with chemical formula Ca10(PO46(OH2 has been widely used in medical field. Both chicken and duck eggshells are mainly composed of calcium carbonate. An attempt has been made to fabricate nanohydroxyapatite (nHA by chicken (CES and duck eggshells (DES as calcium carbonate source (CaCO3. CES and DES were reacted with diammonium hydrogen [(NH42HPO4] solution and subjected to microwave heating at 15 mins. Under the effect of microwave irradiation, nHA was produced directly in the solution and involved in crystallographic transformation. Sample characterization was done using by X-ray diffraction (XRD, fourier transform infrared spectroscopy (FTIR, and scanning electron microscopy (SEM.

Test of a mosquito eggshell isolation method and subsampling procedure.

Science.gov (United States)

Turner, P A; Streever, W J

1997-03-01

Production of Aedes vigilax, the common salt-marsh mosquito, can be assessed by determining eggshell densities found in soil. In this study, 14 field-collected eggshell samples were used to test a subsampling technique and compare eggshell counts obtained with a flotation method to those obtained by direct examination of sediment (DES). Relative precision of the subsampling technique was assessed by determining the minimum number of subsamples required to estimate the true mean and confidence interval of a sample at a predetermined confidence level. A regression line was fitted to cube-root transformed eggshell counts obtained from flotation and DES and found to be significant (P eggshells present. Eggshells obtained with the flotation method can be used to predict those from DES using the following equation: DES count = [1.386 x (flotation count)0.33 - 0.01]3.

Sorption mechanism of Cd(II) from water solution onto chicken eggshell

Science.gov (United States)

Flores-Cano, Jose Valente; Leyva-Ramos, Roberto; Mendoza-Barron, Jovita; Guerrero-Coronado, Rosa María; Aragón-Piña, Antonio; Labrada-Delgado, Gladis Judith

2013-07-01

The mechanism and capacity of eggshell for sorbing Cd(II) from aqueous solution was examined in detail. The eggshell was characterized by several techniques. The eggshell was mainly composed of Calcite (CaCO3). The surface charge distribution was determined by acid-base titration and the point of zero charge (PZC) of the eggshell was found to be 11.4. The sorption equilibrium data were obtained in a batch adsorber, and the adsorption isotherm of Langmuir fitted the data quite well. The sorption capacity of eggshell increased while raising the pH from 4 to 6, this tendency was attributed to the electrostatic interaction between the Cd2+ in solution and the surface of the eggshell. Furthermore, the sorption capacity was augmented by increasing the temperature from 15 to 35 °C because the sorption was endothermic. The sorption of Cd(II) occurred mainly onto the calcareous layer of the eggshell, but slightly on the membrane layer. It was demonstrated that the sorption of Cd(II) was not reversible, and the main sorption mechanisms were precipitation and ion exchange. The precipitation of (Cd,Ca)CO3 on the surface of the eggshell was corroborated by SEM and XRD analysis.

Hierarchical structure and mechanical properties of snake (Naja atra) and turtle (Ocadia sinensis) eggshells.

Science.gov (United States)

Chang, Yin; Chen, Po-Yu

2016-02-01

After hundreds of million years of evolution, natural armors have evolved in various organisms, and has manifested in diverse forms such as eggshells, abalone shells, alligator osteoderms, turtle shells, and fish scales. Eggshells serve as multifunctional shields for successful embryogenesis, such as protection, moisture control and thermal regulation. Unlike calcareous avian eggshells which are brittle and hard, reptilians have leathery eggshells that are tough and flexible. Reptilian eggshells can withstand collision damages when laid in holes and dropped onto each other, and reduce abrasion caused by buried sand. In this study, we investigate structure and mechanical properties of eggshells of Taiwan cobra snake (Naja atra) and Chinese striped-neck turtle (Ocadia sinensis). From Acid Fuchsin Orange G (AFOG) staining and ATR-FTIR examination, we found that both eggshells are mainly composed of keratin. The mechanical properties of demineralized snake and turtle eggshells were evaluated by tensile and fracture tests and show distinctly difference. Turtle eggshells are relatively stiff and rigid, while snake eggshells behave as elastomers, which are highly extensible and reversible. The exceptional deformability (110-230% tensile strain) and toughness of snake eggshells are contributed by the wavy and random arrangement of keratin fibers as well as collagen layers. Multi-scale toughening mechanisms of snake eggshells were observed and elucidated, including crack deflection and twisting, fibers reorientation, sliding and bridging, inter-laminar shear effect, as well as the α-β phase transition of keratin. Inspirations from the structural and mechanical designs of reptilian eggshells may lead to the synthesis of tough, extensible, lightweight composites which could be further applied in the flexible devices, packaging and bio-medical fields. Amniotic eggshells serve as multifunctional shields for successful embryogenesis. The avian eggshells have been extensively

Fire Propagation Performance of Intumescent Fire Protective Coatings Using Eggshells as a Novel Biofiller

Directory of Open Access Journals (Sweden)

M. C. Yew

2014-01-01

Full Text Available This paper aims to synthesize and characterize an effective intumescent fire protective coating that incorporates eggshell powder as a novel biofiller. The performances of thermal stability, char formation, fire propagation, water resistance, and adhesion strength of coatings have been evaluated. A few intumescent flame-retardant coatings based on these three ecofriendly fire retardant additives ammonium polyphosphate phase II, pentaerythritol and melamine mixed together with flame-retardant fillers, and acrylic binder have been prepared and designed for steel. The fire performance of the coatings has conducted employing BS 476: Part 6-Fire propagation test. The foam structures of the intumescent coatings have been observed using field emission scanning electron microscopy. On exposure, the coated specimens’ B, C, and D had been certified to be Class 0 due to the fact that their fire propagation indexes were less than 12. Incorporation of ecofriendly eggshell, biofiller into formulation D led to excellent performance in fire stopping (index value, (I=4.3 and antioxidation of intumescent coating. The coating is also found to be quite effective in water repellency, uniform foam structure, and adhesion strength.

A comparative study on different burning method of sewage sludge ash in mortar brick with eggshell powder as additive

Science.gov (United States)

Ing, Doh Shu; Azed, Muhammad Aizat; Chin, Siew Choo

2017-11-01

Population growth that increase every year has led to the increasing amount of waste generated annually. The content of heavy metal Cadmium (Cd), Lead (Pb) and Zinc (Zn) represent the biggest concentrations of heavy metals in sewage sludge waste which can be the source of pollution. Furthermore, the excessive disposal of eggshells waste to landfills may attract rats and worms due to the organic protein matrix that may pose health problem to the public. In the last decade, the demand on cement mortar brick has increased has resulted in higher cement production. However, cement plant is one of the major contributors of carbon dioxide emission. Hence, this research focuses on the production of environmental friendly cement with sewage sludge since there is occurrence of pozolonic material in Sewage Sludge Ash (SSA). From the initial finding, the major components of SSA are Silicon Dioxide (SiO2), Calcium oxide (CaO), Aluminium Oxide (Al2O3), Iron (III) Oxide (Fe2O3), Sodium Oxide (Na2O), Potassium oxide (K2O), Magnesium Oxide (MgO) and Iron (II) Oxide (FeO). Sewage sludge needed to be incinerated to remove the heavy metal before it can be used as cement replacement in mortar brick production. The sewage sludge were treated using two methods namely incineration and microwave. Both types of sewage sludge were then added with eggshell powder as additive. Eggshell powder act as additive in this research due to its high content of calcium carbonate and has nearly same composition of limestone used in the production of cement. Different percentages of Eggshell Powder (ESP) (0%, 5%, 10%, 15%) and 10% fixed of Microwaved Sewage Sludge Ash (MSSA) and Incinerated Sewage Sludge Ash (ISSA) as optimum dosage partially replacing the cement used to test the brick mortar properties in term of compressive strength, flexural strength and also water absorption. Result showed that ISSA with 5% of ESP is the most optimum brick with highest compressive strength and flexural strength

Global model for the lithospheric strength and effective elastic thickness

OpenAIRE

Magdala Tesauro; Mikhail Kaban; S. A. P. L. Cloetingh

2013-01-01

Global distribution of the strength and effective elastic thickness (Te) of the lithosphere are estimated using physical parameters from recent crustal and lithospheric models. For the Te estimation we apply a new approach, which provides a possibility to take into account variations of Young modulus (E) within the lithosphere. In view of the large uncertainties affecting strength estimates, we evaluate global strength and Te distributions for possible end-member ‘hard’ (HRM) and a ‘soft’ (SR...

Recycled Aluminium Cans/Eggshell Composites: Evaluation of Mechanical and Wear Resistance Properties

Directory of Open Access Journals (Sweden)

J.O. Agunsoye

2015-03-01

Full Text Available Aluminium based metal matrix composites have been produced from recycled aluminium cans and 150µm sized eggshell particles using a stir cast process. The mechanical properties of the control and aluminium can/eggshell composites produced have been investigated. The microstructures of the aluminium can/eggshell composites were examined with the aids of Scanning Electron Microscope (SEM after the sample surfaces have been carefully prepared and etched with aqueous solution of 0.5 cm3 nitric acid. Micrographs revealed that there was a homogenous distribution of eggshell particles within the aluminium can matrix. An indication of effective stirring action during the melting process. The wear resistance was also investigated under different applied loads (6 to 14 N on an abrasive surface emery paper of grade 220. The results revealed an increase in Young’s modulus of elasticity and yield stress from 1,206.45 and 50.23 Mpa respectively of the cast aluminium can with 0 % eggshell particle to the maximum of 3,258.87and 73.2 MPa of aluminium can/12 % eggshell composites. The hardness values increased from 66.23 to 75.13 VN. There was a gradual increase in wear rate of the tested samples as the applied load increased. However, the wear resistance of the aluminium can/6 % eggshell and aluminium can/12 % eggshell composites increased significantly. Hence, recycling of aluminium cans and eggshells can be harnessed into development of useful engineering metal matrix composite materials.

Strength-toughness requirements for thick walled high pressure vessels

International Nuclear Information System (INIS)

Kapp, J.A.

1990-01-01

The strength and toughness requirements of materials for use in high pressure vessels has been the subject of some discussion in the meetings of the Materials Task Group of the Special Working Group High Pressure Vessels. A fracture mechanics analysis has been performed to theoretically establish the required toughness for a high pressure vessel. This paper reports that the analysis performed is based on the validity requirement for plane strain fracture of fracture toughness test specimens. This is that at the fracture event, the crack length, uncracked ligament, and vessel length must each be greater than fifty times the crack tip plastic zone size for brittle fracture to occur. For high pressure piping applications, the limiting physical dimension is the uncracked ligament, as it can be assumed that the other dimensions are always greater than fifty times the crack tip plastic zone. To perform the fracture mechanics analysis several parameters must be known: these include vessel dimensions, material strength, degree of autofrettage, and design pressure. Results of the analysis show, remarkably, that the effects of radius ratio, pressure and degree of autofrettage can be ignored when establishing strength and toughness requirements for code purposes. The only parameters that enter into the calculation are yield strength, toughness and vessel thickness. The final results can easily be represented as a graph of yield strength against toughness on which several curves, one for each vessel thickness, are plotted

Eggshell and Bacterial Cellulose Composite Membrane as Absorbent Material in Active Packaging

Directory of Open Access Journals (Sweden)

S. Ummartyotin

2016-01-01

Full Text Available Bacterial cellulose and eggshell composite was successfully developed. Eggshell was mixed with bacterial cellulose suspension and it was casted as a composite film. CaCO3 derived from eggshell was compared with its commercial availability. It can be noted that good dispersion of eggshell particle was prepared. Eggshell particle was irregular in shape with a variation in size. It existed in bacterial cellulose network. Characterization on composite was focused on thermal and mechanical properties. It showed that flexibility and thermal stability of composite were enhanced. No significant effect of mechanical properties was therefore observed. The thermal stability of composite was stable up to 300°C. The adsorption experiment on water and vegetable oil capacity was performed. The enhancement on adsorption was due to the existence of eggshell in bacterial cellulose composite. It exhibited the potential to be a good candidate for absorbent material in active packaging.

Productivity, embryo and eggshell characteristics, and contaminants in bald eagles from the Great Lakes, USA, 1986 to 2000

Science.gov (United States)

Best, David A.; Elliott, Kyle; Bowerman, William; Shieldcastle, Mark C.; Postupalsky, Sergej; Kubiak, Timothy J.; Tillitt, Donald E.; Elliott, John E.

2010-01-01

Chlorinated hydrocarbon concentrations in eggs of fish-eating birds from contaminated environments such as the Great Lakes of North America tend to be highly intercorrelated, making it difficult to elucidate mechanisms causing reproductive impairment, and to ascribe cause to specific chemicals. An information- theoretic approach was used on data from 197 salvaged bald eagle (Haliaeetus leucocephalus) eggs (159 clutches) that failed to hatch in Michigan and Ohio, USA (1986–2000). Contaminant levels declined over time while eggshell thickness increased, and by 2000 was at pre-1946 levels. The number of occupied territories and productivity increased during 1981 to 2004. For both the entire dataset and a subset of nests along the Great Lakes shoreline, polychlorinated biphenyls (ΣPCBs, fresh wet wt) were generally included in the most parsimonious models (lowest-Akaike's information criterion [AICs]) describing productivity, with significant declines in productivity observed above 26 µg/g ΣPCBs (fresh wet wt). Of 73 eggs with a visible embryo, eight (11%) were abnormal, including three with skewed bills, but they were not associated with known teratogens, including ΣPCBs. Eggs with visible embryos had greater concentrations of all measured contaminants than eggs without visible embryos; the most parsimonious models describing the presence of visible embryos incorporated dieldrin equivalents and dichlorodiphenyldichloroethylene (DDE). There were significant negative correlations between eggshell thickness and all contaminants, with ΣPCBs included in the most parsimonious models. There were, however, no relationships between productivity and eggshell thickness or Ratcliffe's index. The ΣPCBs and DDE were negatively associated with nest success of bald eagles in the Great Lakes watersheds, but the mechanism does not appear to be via shell quality effects, at least at current contaminant levels, while it is not clear what other mechanisms were involved.

Analysis of Siamese Crocodile (Crocodylus siamensis) Eggshell Proteome

Czech Academy of Sciences Publication Activity Database

Mikšík, Ivan; Pataridis, Statis; Eckhardt, Adam; Sedmera, David

2018-01-01

Roč. 37, č. 1 (2018), s. 21-37 ISSN 1572-3887 R&D Projects: GA ČR(CZ) GA15-01948S; GA ČR(CZ) GA16-02972S Institutional support: RVO:67985823 Keywords : protein s of eggshell * eggshell pigment * crocodile Subject RIV: CB - Analytical Chemistry, Separation OBOR OECD: Analytical chemistry Impact factor: 1.139, year: 2016

Eggshell membrane-templated porous gold membranes using nanoparticles as building blocks

International Nuclear Information System (INIS)

Ashraf, S.; Khalid, Z. M.; Hussain, I.

2013-01-01

Highly porous gold membrane-like structures are formed using eggshell membrane, as such and heat denatured, as a template and gold nanoparticles as building blocks. Gold nanoparticles were produced in-situ on the eggshell membranes without using additional reducing agents. The morphology and loading of gold nanoparticles can easily be controlled by adjusting the pH and thus the redox potential of eggshell membranes. Lower pH favored the formation of irregularly-shaped but dense gold macro/ nanocrystals whereas higher pH(8-9) favored the formation of fairly uniform but less dense gold nanoparticles onto the eggshell membranes. Heat treatment of eggshell membrane-gold nanoparticle composites formed at pH 8-9 led to the formation of highly porous membrane like gold while mimicking the original structure of eggshell membrane. All these materials have been thoroughly characterized using field emission scanning electron microscopy (FESEM), energy dispersive X-ray spectroscopy (EDX), and inductively coupled plasma - atomic emission spectroscopy (ISP-AES). These highly porous membrane-like gold materials may have potential applications in catalysis, biosensors, electrode materials, optically selective coatings, heat dissipation and biofiltration. (author)

Heavy metals and metalloids in egg contents and eggshells of passerine birds from Arizona

Science.gov (United States)

Mora, Miguel A.

2003-01-01

Concentrations of inorganic elements were determined in eggs of passerine birds including the endangered southwestern willow flycatcher (Empidonax traillii extimus) from four regions in Arizona. The main aim of the study was to determine the distribution of metals in egg contents and eggshells, with emphasis on the deposition of Sr in eggshells. Seventy eggs of 11 passerine species were collected at four nesting locations during 2000. Aluminum, Ba, Cr, Cu, Mn, Se, Sr, and Zn, were detected primarily in egg contents of all bird species. Arsenic, Ni, Pb, and V were detected primarily in eggshells. A proportion of most inorganic elements accumulated in the eggshell. Concentrations of Ba, Cu, Mn, Se, Sr, and Zn in egg contents and As, Ba, Cu, and V in eggshells of yellow-breasted chats (Icteria virens) were similar among locations. However, concentrations of Mn, Ni, Sr, and Zn in eggshells were significant different among locations. Except for Cu, Mn, Se, and Zn, concentrations of inorganic elements were 2–35 times greater in eggshells than in eggs. Most concentrations of metals and metalloids in eggs and eggshells of all the bird species were below levels known to affect reproduction or that have other deleterious effects. However, I found somewhat elevated concentrations of Sr in eggshells (highest mean=1505 μg/g dw, n=3) of yellow-breasted chats and willow flycatchers, and in egg contents of yellow warblers (Dendroica petechia) and song sparrows (Melospiza melodia). Whether current observed concentrations of Sr in eggshells are affecting nesting birds in Arizona remains to be determined. Strontium and other metals could be associated with lower hatching success in some areas. This study shows that a proportion of many inorganic elements accumulates in the eggshell and that the potential effects on the proper structure and functioning of the eggshell should not be ignored.

Heavy metals and metalloids in egg contents and eggshells of passerine birds from Arizona

International Nuclear Information System (INIS)

Mora, Miguel A.

2003-01-01

High concentrations of Sr in eggshells may be associated with lower hatching success of some passerine birds. - Concentrations of inorganic elements were determined in eggs of passerine birds including the endangered southwestern willow flycatcher (Empidonax traillii extimus) from four regions in Arizona. The main aim of the study was to determine the distribution of metals in egg contents and eggshells, with emphasis on the deposition of Sr in eggshells. Seventy eggs of 11 passerine species were collected at four nesting locations during 2000. Aluminum, Ba, Cr, Cu, Mn, Se, Sr, and Zn, were detected primarily in egg contents of all bird species. Arsenic, Ni, Pb, and V were detected primarily in eggshells. A proportion of most inorganic elements accumulated in the eggshell. Concentrations of Ba, Cu, Mn, Se, Sr, and Zn in egg contents and As, Ba, Cu, and V in eggshells of yellow-breasted chats (Icteria virens) were similar among locations. However, concentrations of Mn, Ni, Sr, and Zn in eggshells were significant different among locations. Except for Cu, Mn, Se, and Zn, concentrations of inorganic elements were 2-35 times greater in eggshells than in eggs. Most concentrations of metals and metalloids in eggs and eggshells of all the bird species were below levels known to affect reproduction or that have other deleterious effects. However, I found somewhat elevated concentrations of Sr in eggshells (highest mean=1505 μg/g dw, n=3) of yellow-breasted chats and willow flycatchers, and in egg contents of yellow warblers (Dendroica petechia) and song sparrows (Melospiza melodia). Whether current observed concentrations of Sr in eggshells are affecting nesting birds in Arizona remains to be determined. Strontium and other metals could be associated with lower hatching success in some areas. This study shows that a proportion of many inorganic elements accumulates in the eggshell and that the potential effects on the proper structure and functioning of the eggshell

Immobilization of lead in a Korean military shooting range soil using eggshell waste: An integrated mechanistic approach

Energy Technology Data Exchange (ETDEWEB)

Ahmad, Mahtab [Department of Biological Environment, Kangwon National University, Chuncheon 200-701 (Korea, Republic of); Hashimoto, Yohey [Department of Bioresource Science, Mie University, 1577 Kurima-machiya, Mie 514-8507 (Japan); Moon, Deok Hyun [Department of Environmental Engineering, Chosun University, Gwangju 501-759 (Korea, Republic of); Lee, Sang Soo, E-mail: sslee97@kangwon.ac.kr [Department of Biological Environment, Kangwon National University, Chuncheon 200-701 (Korea, Republic of); Ok, Yong Sik, E-mail: soilok@kangwon.ac.kr [Department of Biological Environment, Kangwon National University, Chuncheon 200-701 (Korea, Republic of)

2012-03-30

Highlights: Black-Right-Pointing-Pointer Eggshell and calcined eggshell immobilized Pb in the shooting range soil. Black-Right-Pointing-Pointer Calcined eggshell was more effective on Pb immobilization compared to eggshell. Black-Right-Pointing-Pointer Exchangeable Pb fractions were transformed to carbonate bound fractions. Black-Right-Pointing-Pointer Calcined eggshell stabilized Pb by enwrapping into calcium silicate hydrate. Black-Right-Pointing-Pointer Soil Pb toxicity can be reduced by applying eggshell and calcined eggshell. - Abstract: This study evaluated the effectiveness of eggshell and calcined eggshell on lead (Pb) immobilization in a shooting range soil. Destructive and non-destructive analytical techniques were employed to determine the mechanism of Pb immobilization. The 5% additions of eggshell and calcined eggshell significantly decreased the TCLP-Pb concentration by 68.8% due mainly to increasing soil pH. Eggshell and calcined-eggshell amendments decreased the exchangeable Pb fraction to {approx}1% of the total Pb in the soil, while the carbonate-associated Pb fraction was increased to 40.0-47.1% at >15% application rates. The thermodynamic modeling on Pb speciation in the soil solution predicted the precipitation of Pb-hydroxide [Pb(OH){sub 2}] in soils amended with eggshell and calcined eggshell. The SEM-EDS, XAFS and elemental dot mapping revealed that Pb in soil amended with calcined eggshell was associated with Si and Ca, and may be immobilized by entrapping into calcium-silicate-hydrate. Comparatively, in the soil amended with eggshell, Pb was immobilized via formation of Pb-hydroxide or lanarkite [Pb{sub 2}O(SO{sub 4})]. Applications of amendments increased activities of alkaline phosphatase up to 3.7 times greater than in the control soil. The use of eggshell amendments may have potential as an integrated remediation strategy that enables Pb immobilization and soil biological restoration in shooting range soils.

Immobilization of lead in a Korean military shooting range soil using eggshell waste: An integrated mechanistic approach

International Nuclear Information System (INIS)

Ahmad, Mahtab; Hashimoto, Yohey; Moon, Deok Hyun; Lee, Sang Soo; Ok, Yong Sik

2012-01-01

Highlights: ► Eggshell and calcined eggshell immobilized Pb in the shooting range soil. ► Calcined eggshell was more effective on Pb immobilization compared to eggshell. ► Exchangeable Pb fractions were transformed to carbonate bound fractions. ► Calcined eggshell stabilized Pb by enwrapping into calcium silicate hydrate. ► Soil Pb toxicity can be reduced by applying eggshell and calcined eggshell. - Abstract: This study evaluated the effectiveness of eggshell and calcined eggshell on lead (Pb) immobilization in a shooting range soil. Destructive and non-destructive analytical techniques were employed to determine the mechanism of Pb immobilization. The 5% additions of eggshell and calcined eggshell significantly decreased the TCLP-Pb concentration by 68.8% due mainly to increasing soil pH. Eggshell and calcined-eggshell amendments decreased the exchangeable Pb fraction to ∼1% of the total Pb in the soil, while the carbonate-associated Pb fraction was increased to 40.0–47.1% at >15% application rates. The thermodynamic modeling on Pb speciation in the soil solution predicted the precipitation of Pb-hydroxide [Pb(OH) 2 ] in soils amended with eggshell and calcined eggshell. The SEM-EDS, XAFS and elemental dot mapping revealed that Pb in soil amended with calcined eggshell was associated with Si and Ca, and may be immobilized by entrapping into calcium-silicate-hydrate. Comparatively, in the soil amended with eggshell, Pb was immobilized via formation of Pb-hydroxide or lanarkite [Pb 2 O(SO 4 )]. Applications of amendments increased activities of alkaline phosphatase up to 3.7 times greater than in the control soil. The use of eggshell amendments may have potential as an integrated remediation strategy that enables Pb immobilization and soil biological restoration in shooting range soils.

Adhesive Strength of dry Adhesive Structures Depending on the Thickness of Metal Coating

International Nuclear Information System (INIS)

Kim, Gyu Hye; Kwon, Da Som; Kim, Mi Jung; Kim, Su Hee; Yoon, Ji Won; An, Tea Chang; Hwang, Hui Yun

2016-01-01

Recently, engineering applications have started to adopt solutions inspired by nature. The peculiar adhesive properties of gecko skin are an example, as they allow the animal to move freely on vertical walls and even on ceilings. The high adhesive forces between gecko feet and walls are due to the hierarchical microscopical structure of the skin. In this study, the effect of metal coatings on the adhesive strength of synthetic, hierarchically structured, dry adhesives was investigated. Synthetic dry adhesives were fabricated using PDMS micro-molds prepared by photolithography. Metal coatings on synthetic dry adhesives were formed by plasma sputtering. Adhesive strength was measured by pure shear tests. The highest adhesion strengths were found with coatings composed of 4 nm thick layers of Indium, 8 nm thick layers of Zinc and 6 nm thick layers of Gold, respectively

Adhesive Strength of dry Adhesive Structures Depending on the Thickness of Metal Coating

Energy Technology Data Exchange (ETDEWEB)

Kim, Gyu Hye; Kwon, Da Som; Kim, Mi Jung; Kim, Su Hee; Yoon, Ji Won; An, Tea Chang; Hwang, Hui Yun [Andong National Univ., Andong (Korea, Republic of)

2016-07-15

Recently, engineering applications have started to adopt solutions inspired by nature. The peculiar adhesive properties of gecko skin are an example, as they allow the animal to move freely on vertical walls and even on ceilings. The high adhesive forces between gecko feet and walls are due to the hierarchical microscopical structure of the skin. In this study, the effect of metal coatings on the adhesive strength of synthetic, hierarchically structured, dry adhesives was investigated. Synthetic dry adhesives were fabricated using PDMS micro-molds prepared by photolithography. Metal coatings on synthetic dry adhesives were formed by plasma sputtering. Adhesive strength was measured by pure shear tests. The highest adhesion strengths were found with coatings composed of 4 nm thick layers of Indium, 8 nm thick layers of Zinc and 6 nm thick layers of Gold, respectively.

[The effect of core veneer thickness ratio on the flexural strength of diatomite-based dental ceramic].

Science.gov (United States)

Jiang, Jie; Zhang, Xin; Gao, Mei-qin; Zhang, Fei-min; Lu, Xiao-li

2015-06-01

To evaluate the effect of different core veneer thickness ratios on the flexural strength and failure mode of bilayered diatomite-based dental ceramics. Diatomite-based dental ceramics blocks (16 mm×5.4 mm×1 mm) were sintered with different thickness of veneer porcelains: 0 mm (group A), 0.6 mm (group B), 0.8 mm (group C) and 1.0 mm (group D). Flexural strength was detected and scanning electron microscope was used to observe the interface microstructure. Statistical analysis was performed using SPSS 17.0 software package. With the increase of the thickness of the veneer porcelain, flexural strength of group C showed highest flexural strength up to (277.24±5.47) MPa. Different core veneer thickness ratios can significantly influence the flexural strength of bilayered diatomite-based dental ceramics. Supported by Science and Technology Projects of Nantong City (HS2013010).

A 700-year record of mercury in avian eggshells of Guangjin Island, South China Sea

Energy Technology Data Exchange (ETDEWEB)

Xu Liqiang [Institute of Polar Environment, University of Science and Technology of China, Hefei, Anhui 230026 (China); USTC-CityU Joint Advanced Research Center, Suzhou, Jiangsu 215123 (China); Liu Xiaodong, E-mail: ycx@ustc.edu.cn [Institute of Polar Environment, University of Science and Technology of China, Hefei, Anhui 230026 (China); Sun Liguang, E-mail: slg@ustc.edu.cn [Institute of Polar Environment, University of Science and Technology of China, Hefei, Anhui 230026 (China); Chen Qianqian; Yan Hong; Liu Yi; Luo Yuhan; Huang Jing [Institute of Polar Environment, University of Science and Technology of China, Hefei, Anhui 230026 (China)

2011-04-15

Ancient eggshells over the past 700 years were extracted from an ornithogenic sediment profile on Guangjin Island, South China Sea. Based on SEM and nitrogen isotope analyses, we determined that neither post-depositional processes nor seabirds' dietary changes had a large influence on eggshell Hg levels. The historical change of Hg in these eggshells was reconstructed. Eggshell Hg was a marker for past Hg deposition in marine environment. The eggshell Hg showed three small peaks at around 1300AD, 1600 AD and 1700-1750AD and rapid increase since 1800 AD. Before 1970 AD the Hg deposition in the Xisha area had global distribution characteristics, with increased Hg emissions due to global anthropogenic activities in industrial times. However, after 1970 AD, a further sharp increase up to present day occurred, implying that the Hg production center had gradually shifted from Europe and America to Asia. - Research highlights: > Eggshell Hg is a marker for past mercury deposition in marine environment. > This is a Hg record from ancient sequential eggshell samples. > The 700-year record of eggshell Hg is closely related to human activities. > Eggshell Hg suggests the increase of Hg production in Asia over the past decades. - Our work provides a potential use of ancient sequential eggshells to reconstruct past mercury deposition in marine ecosystems.

Viability of Eggshells Ash Affecting the Setting Time of Cement

OpenAIRE

Fazeera Ujin; Kamran Shavarebi Ali; Zarina Yasmin Hanur Harith

2016-01-01

This research paper reports on the feasibility and viability of eggshells ash and its effects on the water content and setting time of cement. An experiment was carried out to determine the quantity of water required in order to follow standard cement paste of normal consistency in accordance with MS EN 196-3:2007. The eggshells ash passing the 90µm sieve was used in the investigation. Eggshells ash with percentage of 0%, 0.1%, 0.5%, 1.0%, 1.5% and 2.0% were constituted to replace the cement....

Evolution and characterization of eggshell as a potential candidate of raw material

Directory of Open Access Journals (Sweden)

T. Zaman

Full Text Available Abstract Characterization of both uncalcined and calcined eggshells was done in this work. Raw eggshells turned out as a good source of calcite phase. Calcined eggshells had a mixture of lime and portlandite phase. A significant impact of calcination temperature on the percentage of generated phases was observed. Qualitative as well as semi-quantitative phase analysis, morphological characterization and physical property estimation was done for the produced powder. The influence of synthesized raw material on soil stabilization and biomaterial formation was further assessed. The eggshell turned out as a potential source of raw material for various sectors.

Influence of Casting Section Thickness on Fatigue Strength of Austempered Ductile Iron

Science.gov (United States)

Olawale, J. O.; Ibitoye, S. A.

2017-10-01

The influence of casting section thickness on fatigue strength of austempered ductile iron was investigated in this study. ASTM A536 65-45-12 grade of ductile iron was produced, machined into round samples of 10, 15, 20 and 25 mm diameter, austenitized at a temperature of 820 °C, quenched into an austempering temperature (TA) of 300 and 375 °C and allowed to be isothermally transformed at these temperatures for a fixed period of 2 h. From the samples, fatigue test specimens were machined to conform to ASTM E-466. Scanning electron microscopy (SEM) and x-ray diffraction (XRD) methods were used to characterize microstructural morphology and phase distribution of heat-treated samples. The fatigue strength decreases as the section thickness increases. The SEM image and XRD patterns show a matrix of acicular ferrite and carbon-stabilized austenite with ferrite coarsening and volume fraction of austenite reducing as the section thickness increases. The study concluded that the higher the value of carbon-stabilized austenite the higher the fatigue strength while it decreases as the ausferrite structure becomes coarse.

A 700-year record of mercury in avian eggshells of Guangjin Island, South China Sea

International Nuclear Information System (INIS)

Xu Liqiang; Liu Xiaodong; Sun Liguang; Chen Qianqian; Yan Hong; Liu Yi; Luo Yuhan; Huang Jing

2011-01-01

Ancient eggshells over the past 700 years were extracted from an ornithogenic sediment profile on Guangjin Island, South China Sea. Based on SEM and nitrogen isotope analyses, we determined that neither post-depositional processes nor seabirds' dietary changes had a large influence on eggshell Hg levels. The historical change of Hg in these eggshells was reconstructed. Eggshell Hg was a marker for past Hg deposition in marine environment. The eggshell Hg showed three small peaks at around 1300AD, 1600 AD and 1700-1750AD and rapid increase since 1800 AD. Before 1970 AD the Hg deposition in the Xisha area had global distribution characteristics, with increased Hg emissions due to global anthropogenic activities in industrial times. However, after 1970 AD, a further sharp increase up to present day occurred, implying that the Hg production center had gradually shifted from Europe and America to Asia. - Research highlights: → Eggshell Hg is a marker for past mercury deposition in marine environment. → This is a Hg record from ancient sequential eggshell samples. → The 700-year record of eggshell Hg is closely related to human activities. → Eggshell Hg suggests the increase of Hg production in Asia over the past decades. - Our work provides a potential use of ancient sequential eggshells to reconstruct past mercury deposition in marine ecosystems.

The microbial burden load of eggshells from different poultry rearing ...

African Journals Online (AJOL)

The results obtained from the study revealed that eggshell samples from different poultry rearing systems (battery cage, deep litter and free-range chicken eggs) were contaminated with bacterial and fungal species of public health concern. Microbial species isolated from eggshells were Enterobacter aerogenes, ...

Effect of layered manufacturing techniques, alloy powders, and layer thickness on metal-ceramic bond strength.

Science.gov (United States)

Ekren, Orhun; Ozkomur, Ahmet; Ucar, Yurdanur

2018-03-01

Direct metal laser sintering (DMLS) and direct metal laser melting (DMLM) have become popular for fabricating the metal frameworks of metal-ceramic restorations. How the type of layered manufacturing device, layer thickness, and alloy powder may affect the bond strength of ceramic to metal substructure is unclear. The purpose of this in vitro study was to evaluate the bond strength of dental porcelain to metal frameworks fabricated using different layered manufacturing techniques (DMLS and DMLM), Co-Cr alloy powders, and layer thicknesses and to evaluate whether a correlation exists between the bond strength and the number of ceramic remnants on the metal surface. A total of 75 bar-shaped metal specimens (n=15) were fabricated using either DMLS or DMLM. The powder alloys used were Keramit NP-S and EOS-Cobalt-Chrome SP-2 with layer thicknesses of 20 μm and 30 μm. After ceramic application, the metal-ceramic bond strength was evaluated with a 3-point-bend test. Three-way ANOVA followed by the Tukey honest significance difference test were used for statistical analysis (α=.05). De-bonding surface microstructure was observed with scanning electron microscopy. Energy dispersive spectroscopy analysis was conducted to evaluate the correlation between ceramic remnants on the metal surface and bond strength values. The mean bond strength value of DMLS was significantly higher than that of DMLM. While no statistically significant difference was found between layer thicknesses, alloy powders closely affected bond strength. Statistical comparisons revealed that the highest bond strength could be achieved with DMLS-Cobalt-Chrome SP2-20μm, and the lowest bond strength was observed in DMLS-Keramit NP-S-20μm (P≤.05). No correlation was found between porcelain remnants on the metal surface and bond strength values. The layered manufacturing device and the alloy powders evaluated in the current study closely affected the bond strength of dental porcelain to a metal framework

Eggshells – assisted hydrolysis of banana pulp for biogas production

African Journals Online (AJOL)

KARAKANA

In this study, pretreatment of banana pulp using eggshells in both calcined and un-calcined forms to examine the ... Key words: Anaerobic digestion, banana pulp hydrolysis biogas, eggshells. .... obtain fine powder. ..... using pig waste and cassava peels. ... from bioethanol waste: the effect of pH and urea addition to biogas.

Global model for the lithospheric strength and effective elastic thickness

NARCIS (Netherlands)

Tesauro, M.; Kaban, M.K.; Cloetingh, S.A.P.L.

2013-01-01

Global distribution of the strength and effective elastic thickness (Te) of the lithosphere are estimated using physical parameters from recent crustal and lithospheric models. For the Te estimation we apply a new approach, which provides a possibility to take into account variations of Young

Soybean meal enriched with microelements by biosorption--a new biological feed supplement for laying hens. Part I. Performance and egg traits.

Science.gov (United States)

Witkowska, Z; Chojnacka, K; Korczyński, M; Świniarska, M; Saeid, A; Opaliński, S; Dobrzański, Z

2014-05-15

The aim of the study was to evaluate the effect of soybean meal enriched with Cu(II), Zn(II), Fe(II) and Cr(III) by biosorption on egg traits (egg weight, eggshell strength, eggshell thickness, yolk colour, albumen height) and performance of laying hens. Also, the effect of increased microelement doses in biological form on egg quality parameters and hens performance was investigated. A consumer questionnaire was undertaken to evaluate the organoleptic parameters of the eggs. Generally, our study showed that in the groups fed with the new biological supplement, egg quality parameters improved, including eggshell strength, eggshell thickness, albumen height and yolk colour. The biological form of microelements also improved the feed conversion rate, especially in the group fed with a biological form of Cr(III). Moreover, the new supplement improved organoleptic parameters of the eggs, in comparison to the inorganic form of microelements as well as to chelate. Enriched soybean meal could constitute an alternative for currently used feed additives with microelements. Copyright © 2013 Elsevier Ltd. All rights reserved.

Evolution and characterization of eggshell as a potential candidate of raw material

OpenAIRE

Zaman, T.; Mostari, Mst. S.; Mahmood, Md. A. Al; Rahman, Md. S.

2018-01-01

Abstract Characterization of both uncalcined and calcined eggshells was done in this work. Raw eggshells turned out as a good source of calcite phase. Calcined eggshells had a mixture of lime and portlandite phase. A significant impact of calcination temperature on the percentage of generated phases was observed. Qualitative as well as semi-quantitative phase analysis, morphological characterization and physical property estimation was done for the produced powder. The influence of synthesize...

Atmospheric pressure plasma jet treatment of Salmonella Enteritidis inoculated eggshells.

Science.gov (United States)

Moritz, Maike; Wiacek, Claudia; Koethe, Martin; Braun, Peggy G

2017-03-20

Contamination of eggshells with Salmonella Enteritidis remains a food safety concern. In many cases human salmonellosis within the EU can be traced back to raw or undercooked eggs and egg products. Atmospheric pressure plasma is a novel decontamination method that can reduce a wide range of pathogens. The aim of this work was to evaluate the possibility of using an effective short time cold plasma treatment to inactivate Salmonella Enteritidis on the eggshell. Therefore, artificially contaminated eggshells were treated with an atmospheric pressure plasma jet under different experimental settings with various exposure times (15-300s), distances from the plasma jet nozzle to the eggshell surface (5, 8 or 12mm), feed gas compositions (Ar, Ar with 0.2, 0.5 or 1.0% O 2 ), gas flow rates (5 and 7slm) and different inoculations of Salmonella Enteritidis (10 1 -10 6 CFU/cm 2 ). Atmospheric pressure plasma could reduce Salmonella Enteritidis on eggshells significantly. Reduction factors ranged between 0.22 and 2.27 log CFU (colony-forming units). Exposure time and, particularly at 10 4 CFU/cm 2 inoculation, feed gas had a major impact on Salmonella reduction. Precisely, longer exposure times led to higher reductions and Ar as feed gas was more effective than ArO 2 mixtures. Copyright © 2017 Elsevier B.V. All rights reserved.

Effect of limestone particle size on egg production and eggshell ...

African Journals Online (AJOL)

Different limestone particle sizes had no effect on any of the tested egg production and eggshell quality parameters. These results suggested that larger particles limestone are not necessarily essential to provide sufficient Ca2+ to laying hens for egg production and eggshell quality at end-of-lay, provided that the dietary Ca ...

Immobilization of lead in a Korean military shooting range soil using eggshell waste: an integrated mechanistic approach.

Science.gov (United States)

Ahmad, Mahtab; Hashimoto, Yohey; Moon, Deok Hyun; Lee, Sang Soo; Ok, Yong Sik

2012-03-30

This study evaluated the effectiveness of eggshell and calcined eggshell on lead (Pb) immobilization in a shooting range soil. Destructive and non-destructive analytical techniques were employed to determine the mechanism of Pb immobilization. The 5% additions of eggshell and calcined eggshell significantly decreased the TCLP-Pb concentration by 68.8% due mainly to increasing soil pH. Eggshell and calcined-eggshell amendments decreased the exchangeable Pb fraction to ≈ 1% of the total Pb in the soil, while the carbonate-associated Pb fraction was increased to 40.0-47.1% at >15% application rates. The thermodynamic modeling on Pb speciation in the soil solution predicted the precipitation of Pb-hydroxide [Pb(OH)(2)] in soils amended with eggshell and calcined eggshell. The SEM-EDS, XAFS and elemental dot mapping revealed that Pb in soil amended with calcined eggshell was associated with Si and Ca, and may be immobilized by entrapping into calcium-silicate-hydrate. Comparatively, in the soil amended with eggshell, Pb was immobilized via formation of Pb-hydroxide or lanarkite [Pb(2)O(SO(4))]. Applications of amendments increased activities of alkaline phosphatase up to 3.7 times greater than in the control soil. The use of eggshell amendments may have potential as an integrated remediation strategy that enables Pb immobilization and soil biological restoration in shooting range soils. Copyright © 2012 Elsevier B.V. All rights reserved.

Effects of Eggshell Calcium Supplementation on Bone Mass in Postmenopausal Vietnamese Women.

Science.gov (United States)

Sakai, Seigo; Hien, Vu Thi Thu; Tuyen, Le Danh; Duc, Ha Anh; Masuda, Yasunobu; Yamamoto, Shigeru

2017-01-01

Bone mass decreases along with aging, especially for women after menopause because of lower estrogen secretion together with low calcium intake. This study was conducted to study the effect of eggshell calcium supplementation on bone mass in 54 postmenopausal Vietnamese women living in a farming area about 60 km from Hanoi, Vietnam. Sets of 3 subjects matched by age, bone mass, BMI and calcium intake were divided randomly into 3 groups with 18 subjects in each group. The eggshell calcium group was administered 300 mg/d calcium from eggshell, the calcium carbonate group 300 mg/d calcium from calcium carbonate and the placebo group received no calcium supplementation. Bone mass (Speed of Sound (SOS)) was measured at the beginning (the baseline), the middle (6th month) and the end of the study (12th month) by the single blind method. SOS of the eggshell group increased significantly at 12 mo (p0.05). In conclusion, eggshell calcium was more effective in increasing bone mass than calcium carbonate in postmenopausal Vietnamese women.

The evolution of eggshell cuticle in relation to nesting ecology

Science.gov (United States)

Hauber, Mark E.

2016-01-01

Avian eggs are at risk of microbial infection prior to and during incubation. A large number of defence mechanisms have evolved in response to the severe costs imposed by these infections. The eggshell's cuticle is an important component of antimicrobial defence, and its role in preventing contamination by microorganisms in domestic chickens is well known. Nanometer-scale cuticular spheres that reduce microbial attachment and penetration have recently been identified on eggs of several wild avian species. However, whether these spheres have evolved specifically for antimicrobial defence is unknown. Here, we use comparative data on eggshell cuticular structure and nesting ecology to test the hypothesis that birds nesting in habitats with higher risk of infection (e.g. wetter and warmer) are more likely to evolve cuticular nanospheres on their eggshells than those nesting in less risky habitats. We found that nanostructuring, present in 54 of 296 analysed species, is the ancestral condition of avian eggshells and has been retained more often in taxa that nest in humid infection-prone environments, suggesting that they serve critical roles in antimicrobial egg defence. PMID:27488648

Phosphorus removal from aqueous solution in parent and aluminum-modified eggshells: thermodynamics and kinetics, adsorption mechanism, and diffusion process.

Science.gov (United States)

Guo, Ziyan; Li, Jiuhai; Guo, Zhaobing; Guo, Qingjun; Zhu, Bin

2017-06-01

Parent and aluminum-modified eggshells were prepared and characterized with X-ray diffraction, specific surface area measurements, infrared spectroscopy, zeta potential, and scanning electron microscope, respectively. Besides, phosphorus adsorptions in these two eggshells at different temperatures and solution pH were carried out to study adsorption thermodynamics and kinetics as well as the mechanisms of phosphorus adsorption and diffusion. The results indicated that high temperature was favorable for phosphorus adsorption in parent and aluminum-modified eggshells. Alkaline solution prompted phosphorus adsorption in parent eggshell, while the maximum adsorption amount was achievable at pH 4 in aluminum-modified eggshell. Adsorption isotherms of phosphorus in these eggshells could be well described by Langmuir and Freundlich models. Phosphorus adsorption amounts in aluminum-modified eggshell were markedly higher compared to those in parent eggshell. Adsorption heat indicated that phosphorus adsorption in parent eggshell was a typically physical adsorption process, while chemical adsorption mechanism of ion exchange between phosphorus and hydroxyl groups on the surface of eggshells was dominated in aluminum-modified eggshell. The time-resolved uptake curves showed phosphorus adsorption in aluminum-modified eggshell was significantly faster than that in parent eggshell. Moreover, there existed two clear steps in time-resolved uptake curves of phosphorus in parent eggshell. Based on pseudo-second order kinetic model and intraparticle diffusion model, we inferred more than one process affected phosphorus adsorption. The first process was the diffusion of phosphorus through water to external surface and the opening of pore channel in the eggshells, and the second process was mainly related to intraparticle diffusion.

Biosorption of strontium ions from aqueous solution using modified eggshell materials

Energy Technology Data Exchange (ETDEWEB)

Metwally, Sayed S.; Rizk, Hoda E.; Gasser, Mona S. [Atomic Energy Authority, Cairo (Egypt). Hot Laboratories Center

2017-07-01

Green composites emphasize renewable starting materials for better economy using biomass materials. Therefore, low-cost composite biosorbent was prepared by modification of eggshell material using heteropoly acid for removal of strontium ions from aqueous solution. The resulted composite was characterized and evaluated for the sorption process using the batch technique. Low concentration of strontium ions was used to evaluate the sorption sensitivity of the prepared composite. The obtained experimental results illustrated that the modification process of eggshell material enhanced the percent uptake from 49.9 to 95.7%. From kinetic studies, the sorption of strontium ions follows the pseudo-second-order kinetic model. The isotherm studies indicated that Langmuir is more applicable than Freundlich isotherm. Moreover, Dubinin-Radushkevich isotherm was studied. Thermodynamic studies revealed that the sorption process is spontaneous and has endothermic nature. Strontium ions can be desorbed from the modified eggshell using HNO{sub 3}, desorption percent was found to be 96.4%; the results revealed the reusability of the modified eggshell for further sorption.

Eggshell apex abnormalities in a free-range hen farm with mycoplasma synoviae and infectious bronchitis virus in Rio de Janeiro state, Brazil

Directory of Open Access Journals (Sweden)

FC dos Santos

2014-06-01

Full Text Available A farm with 3,000 free-range hens between 24 and 65 weeks of age was investigated. These hens were separated in small flocks of 400 to 700 birds, presenting 10 to 23% egg production reduction. Twenty serum samples were collected during the period of drop in egg production and three weeks later for the investigation of Mycoplasma synoviae (MS, M. gallisepticum (MG and Infectious Bronchitis Virus (IBV antibodies using ELISA. At the time of the second collection, egg production had resumed to normal levels; however, with 10.23% of the eggs showed eggshell abnormalities limited to the apex. Eggshell strength was significantly different between normal and those with eggshell apex abnormalities, but not other egg-quality parameters. ELISA tests showed that MS and IBV titers increased during the evaluated period. MS infection was confirmed by culture and by PCR of tracheal swabs. All samples were negative for MG by ELISA and PCR. Further studies with larger samples to ensure the occurrence of this disease in industrial layer flocks in Brazil are under way.

or without eggshell's contamination that produced in Tabriz.

Directory of Open Access Journals (Sweden)

M Khakpoor

2011-08-01

Full Text Available Zoonotic bacterial diseases are considered as the most important human infectious diseases. In this category, a disease that transfer and infect human through food has an special role. Among foods with animal origin, eggs due to their application as food ingredient in food products, like sauces, spices, ice creams and other food products that may use in half cooked or crude forms, always has the potential to transfer microbial pathogens to human. This study is about to prove that presence of remainder feces on eggshells leads the penetration of bacterial agents into egg yolk. A total of 120 daily egg samples (with and without fecal contamination were collected from henneries around Tabriz and transferred immediately to microbiology laboratory. After performing microbial examinations (using BHI Broth, BHI Agar, Blood Agar, Selenite F, Tetrationate, XLD,SS Agar,Gram Staining, Oxidase and Catalase tests, bacteria of eggshells and egg yolks has been identified. Out of 120 eggs, 15.83% bacterial contaminants were found in egg yolks samples. Among them, 73.68%  were gram negative and 26.31% were gram positive. Among gram negatives, Pseudomonas with occurrence of 8.3% and in gram positives group, Bacillus with abundance of  4.16% were the most frequent bacterias. Also in samples collected from eggshells, 99.16% of the eggs demonstrated bacterial contamination which 23.55% of positive samples were among gram negative group and 76.44% were gram positive. The most contribution of eggshell gram negative bacterias were relevant to Pseudomonas, E.coli, Proteus and Citrobacter with respectively 18.33%,10.83%,5.83% and 4.16% rations. Among gram positive bacteria that isolates form eggshell samples for the most frequent bacterias, were Bacillus, Staphylococccus, Streptococcus, Rhodococcus and Micrococcus with respectively 80.00%, 34.16%, 15%, 9.16% and 7.5% rations. Use and consumption of eggs with shells contaminated with faces in food products is a serious

Global model for the lithospheric strength and effective elastic thickness

Science.gov (United States)

Tesauro, Magdala; Kaban, Mikhail K.; Cloetingh, Sierd A. P. L.

2013-08-01

Global distribution of the strength and effective elastic thickness (Te) of the lithosphere are estimated using physical parameters from recent crustal and lithospheric models. For the Te estimation we apply a new approach, which provides a possibility to take into account variations of Young modulus (E) within the lithosphere. In view of the large uncertainties affecting strength estimates, we evaluate global strength and Te distributions for possible end-member 'hard' (HRM) and a 'soft' (SRM) rheology models of the continental crust. Temperature within the lithosphere has been estimated using a recent tomography model of Ritsema et al. (2011), which has much higher horizontal resolution than previous global models. Most of the strength is localized in the crust for the HRM and in the mantle for the SRM. These results contribute to the long debates on applicability of the "crème brulée" or "jelly-sandwich" model for the lithosphere structure. Changing from the SRM to HRM turns most of the continental areas from the totally decoupled mode to the fully coupled mode of the lithospheric layers. However, in the areas characterized by a high thermal regime and thick crust, the layers remain decoupled even for the HRM. At the same time, for the inner part of the cratons the lithospheric layers are coupled in both models. Therefore, rheological variations lead to large changes in the integrated strength and Te distribution in the regions characterized by intermediate thermal conditions. In these areas temperature uncertainties have a greater effect, since this parameter principally determines rheological behavior. Comparison of the Te estimates for both models with those determined from the flexural loading and spectral analysis shows that the 'hard' rheology is likely applicable for cratonic areas, whereas the 'soft' rheology is more representative for young orogens.

Chicken eggshells (Gallus gallus domesticus) as carbonate calcium source for biomaterials production

International Nuclear Information System (INIS)

Junior, E.A. de O.; Bastos, J.S.B.; Silva, R.C. de S.; Macedo, H.R.A.; Macedo, M. O.C.; Bradim, A.S.

2016-01-01

The eggshells present high levels of calcium carbonate. Calcium carbonate obtained from eggshells has been used in the production of biomaterials with applications in bone regeneration, since it is biocompatible. In this work, calcium carbonate was obtained from eggshells to prepare a composite biomaterial. The presence of calcium carbonate bands was observed through spectrometry in the infrared region. Scanning electron microscopy showed the presence of calcium carbonate particles with different sizes and shapes. Carbonate predominance in the form of calcite was also observed through the X-ray diffraction

Ostrich eggshell as an alternative raw material for hydroxyapatite synthesis

International Nuclear Information System (INIS)

Caliman, L.B.; Gouvea, D.

2011-01-01

The goal of this study was to investigate the use of ostrich eggshell for hydroxyapatite synthesis, a biomaterial of great medical importance due to its high biocompatibility. The eggshell was used as calcium ions source due its great containing of CaCO3. For its utilization, the eggshell was calcined and the obtained oxide (CaO) was transformed into Ca(OH)_2. Hydroxyapatite synthesis consisted in a wet precipitation reaction between Ca(OH)_2 and commercial H_3PO_4. The X ray Diffraction analysis has shown that the precipitated Hydroxyapatite calcined at 800°C resulted in a bifasic powder of Hydroxyapatite and β-Tricalcium Phosphate, which proves that this precipitated Hydroxyapatite was deficient in calcium. The Infrared Spectroscopy, showed the presence of CO_3"2"- ions, result of carrying out the reaction in open atmosphere. By Scanning Electron Microscopy nanometric particles arranged in agglomerates were observed and Specific Surface Area measurement resulted in 11,70 m²/g. Following this procedure, the ostrich eggshell gets a technological profitable reuse also environmentally friendly, being transformed in a new product of high aggregate value. (author)

Efeito da forma física da ração sobre a porosidade, espessura da casca, perda de água e eclodibilidade em ovos de perdiz (Rhynchotus rufescens Effect of the physical form of diet on the eggshell porosity and thickness, water loss and hatchability of partridge (Rhynchotus rufescens eggs

Directory of Open Access Journals (Sweden)

ES Nakage

2002-12-01

Full Text Available O objetivo do presente estudo foi avaliar se a forma física da ração (farelada e peletizada afeta a porosidade e espessura da casca, e porcentagem de perda de água e eclodibilidade de ovos de perdiz. Os ovos foram coletados logo após a postura e separados em diferentes intervalos de peso (35-45g, 46-50g, 51-55g, 56-60g e 61-70g, sendo 10 ovos/classe/ração. O número de poros das cascas foi avaliado nas regiões apical, equatorial e basal dos ovos. Utilizou-se um micrômetro digital para a mensuração da espessura das três regiões da casca dos ovos, a partir dos quais obteve-se a espessura média por ovo. Os ovos para avaliação da eclodibilidade e porcentagem de perda de água do ovo até a transferência para o nascedouro (16º dia foram pesados, desinfectados, incubados (T=35,5ºC e UR= 70% e transferidos no 16º dia de incubação para o nascedouro, onde foram mantidos até a eclosão. As análises estatísticas empregadas foram: Análise de Variância e de Correlação, e teste de Tukey 5%. Os dados mostraram que, em perdizes, o número de poros na casca pode variar com a região da casca, peso do ovo e a forma física da ração, e que a ingestão de ração peletizada promove um aumento na espessura da casca dos ovos sem alterar a eclodibilidade e a porcentagem de perda de água dos mesmos durante a incubação.The aim of this study was to determine the effect of the ingestion of meal and pelleted diets on eggshell porosity and thickness, water loss and hatchability percentages of partridge (Rhynchotus rufescens eggs. The eggs (n=100 were divided into five different weight classes (1: 35-45 g, 2: 46-50 g, 3: 51-55 g, 4: 56-60 g, 5: 61-70 g. Parts from different regions (air space, equator and small end of each eggshell were analized in order to count pore numbers. Eggshell thickness measurements were carried out after removal of the egg membranes. The eggs used in the analyses of the water loss and hatchability percentages were

Organchlorine content and shell thickness in brown booby (Sula leucogaster) eggs in the Gulf of California and the southern Pacific coast of Mexico

Energy Technology Data Exchange (ETDEWEB)

Mellink, Eric, E-mail: emellink@cicese.m [Departamento de Biologia de la Conservacion, Centro de Investigacion Cientifica y de Educacion Superior de Ensenada, B.C. Carretera Tijuana-Ensenada Km. 107, 22860 Ensenada, B.C. (Mexico); Riojas-Lopez, Monica E., E-mail: meriojas@cucba.udg.m [Departamento de Ecologia, Centro Universitario de Ciencias Biologicas y Agropecuarias, Universidad de Guadalajara, Km. 15.5 Carretera a Nogales, 45100 Zapopan, Jalisco (Mexico); Luevano-Esparza, Jaime, E-mail: jluevano@cicese.m [Departamento de Biologia de la Conservacion, Centro de Investigacion Cientifica y de Educacion Superior de Ensenada, B.C. Carretera Tijuana-Ensenada Km. 107, 22860 Ensenada, B.C. (Mexico)

2009-07-15

We determined egg concentrations of organochlorines and thickness of eggshells from brown boobies at eight colonies ranging from the northern Gulf of California to southern Mexico. The only common residue was that of DDE, which was found in almost all eggs. DDE content apparently reflected pre-1990 DDT use in nearby agricultural areas and, at one site, intensive mosquito control for high-end tourism development. There were no inter-colony differences in eggshell thickness, and variation in this variable likely reflected individual bird characteristics and/or individual feeding source. This variable was not a good proxy to DDE exposure of brown boobies, under current DDE levels in the brown booby trophic chain. In the northern Gulf of California, eggshell thickness has recovered to pre-DDT conditions. Our data indicate that the Gulf of California and southwestern coast of Mexico have a healthy near-shore marine environment, as far as organochlorines are concerned. - Wide-range, current picture of organochlorine presence in the environment along the western coast of Mexico.

Organchlorine content and shell thickness in brown booby (Sula leucogaster) eggs in the Gulf of California and the southern Pacific coast of Mexico

International Nuclear Information System (INIS)

Mellink, Eric; Riojas-Lopez, Monica E.; Luevano-Esparza, Jaime

2009-01-01

We determined egg concentrations of organochlorines and thickness of eggshells from brown boobies at eight colonies ranging from the northern Gulf of California to southern Mexico. The only common residue was that of DDE, which was found in almost all eggs. DDE content apparently reflected pre-1990 DDT use in nearby agricultural areas and, at one site, intensive mosquito control for high-end tourism development. There were no inter-colony differences in eggshell thickness, and variation in this variable likely reflected individual bird characteristics and/or individual feeding source. This variable was not a good proxy to DDE exposure of brown boobies, under current DDE levels in the brown booby trophic chain. In the northern Gulf of California, eggshell thickness has recovered to pre-DDT conditions. Our data indicate that the Gulf of California and southwestern coast of Mexico have a healthy near-shore marine environment, as far as organochlorines are concerned. - Wide-range, current picture of organochlorine presence in the environment along the western coast of Mexico.

Clumped isotope paleothermometry of eggshells as an indicator of vertebrate endothermy

Science.gov (United States)

Canavan, R. R.; Field, D. J.; Therrien, F.; Zelenitsky, D.; Affek, H. P.

2014-12-01

Isotopic analyses of the calcite or aragonite shells of aquatic organisms are often used in the study of the environmental conditions in which they grow; however, this approach is less straightforward in the terrestrial realm, where environments may be more heterogeneous. In such terrestrial localities, the bioapatite of vertebrate teeth comprises the typical archival material for isotopic analyses. The calcitic eggshells of birds and other reptiles may provide suitable material for isotopic analyses that are aimed at studying their physiology and ecology. Here we apply a novel thermometer, carbonate clumped isotopes (Δ47), to test for endothermy in extinct non-avian dinosaurs in the context provided by eggs of modern reptiles and birds. These Δ47-derived temperatures should reflect the temperature of shell formation, which in endothermic animals such as birds should represent the mother's internal body temperature. In ectothermic animals, the same is true although their body temperatures are more affected by the external environment and thus Δ47 temperatures could more accurately describe local environmental temperatures during eggshell formation. Fossil eggshells represent appropriate material for reconstructing internal body temperatures of extinct non-avian dinosaurs since they mineralized within the mother's body, and fragments of eggshell are commonly recovered from dinosaur-bearing fossil deposits. The dimensions of these fragments provide sufficient material for the relatively large sample required for clumped isotope analysis (~20mg). Fossil eggshell samples from several taxa of Late Cretaceous non-avian dinosaurs were analyzed using Δ47 paleothermometry. Textural inspection was used as a first test for diagenetic alteration of the original calcite, and histological indicators were used for broad taxonomic identifications. Preliminary results of Δ47-derived body temperature estimates from eggshells are consistent with previous body temperatures

Freestanding eggshell membrane-based electrodes for high-performance supercapacitors and oxygen evolution reaction

Science.gov (United States)

Geng, Jing; Wu, Hao; Al-Enizi, Abdullah M.; Elzatahry, Ahmed A.; Zheng, Gengfeng

2015-08-01

A type of freestanding, light-weight eggshell membrane-based electrode is demonstrated for supercapacitors and for oxygen evolution reaction (OER) catalysis. As a widely available daily waste, eggshell membranes have unique porous three-dimensional grid-like fibrous structures with relatively high surface area and abundant macropores, allowing for effective conjugation of carbon nanotubes and growth of NiCo2O4 nanowire arrays, an effective supercapacitor material and OER catalyst. The three-dimensional fibrous eggshell membrane frameworks with carbon nanotubes offer efficient pathways for charge transport, and the macropores between adjacent fibers are fully accessible for electrolytes and bubble evolution. As a supercapacitor, the eggshell membrane/carbon nanotube/NiCo2O4 electrode shows high specific capacitances at current densities from 1 to 20 A g-1, with excellent capacitance retention (>90%) at 10 A g-1 for over 10 000 cycles. When employed as an OER catalyst, this eggshell membrane-based electrode exhibits an OER onset potential of 1.53 V vs. the reversible hydrogen electrode (RHE), and a stable catalytic current density of 20 mA cm-2 at 1.65 V vs. the RHE.A type of freestanding, light-weight eggshell membrane-based electrode is demonstrated for supercapacitors and for oxygen evolution reaction (OER) catalysis. As a widely available daily waste, eggshell membranes have unique porous three-dimensional grid-like fibrous structures with relatively high surface area and abundant macropores, allowing for effective conjugation of carbon nanotubes and growth of NiCo2O4 nanowire arrays, an effective supercapacitor material and OER catalyst. The three-dimensional fibrous eggshell membrane frameworks with carbon nanotubes offer efficient pathways for charge transport, and the macropores between adjacent fibers are fully accessible for electrolytes and bubble evolution. As a supercapacitor, the eggshell membrane/carbon nanotube/NiCo2O4 electrode shows high specific

Eggshell Biliverdin and Protoporphyrin Pigments in a Songbird: Are They Derived from Erythrocytes, Blood Plasma, or the Shell Gland?

Science.gov (United States)

Hargitai, Rita; Boross, Nóra; Hámori, Susanne; Neuberger, Eszter; Nyiri, Zoltán

Biliverdin and protoporphyrin pigments are deposited into the eggshell when the developing egg is in the shell gland. However, the site of synthesis of eggshell pigments is still uncertain, although it may influence the possible costs and potential functions of eggshell coloration in avian species. Eggshell pigments may be derived from red blood cells or be produced in other organs and then transferred to the shell gland, or they may be synthesized de novo in the shell gland. We studied in the canary (Serinus canaria) whether eggshell blue-green and brown pigmentations are associated with experimentally elevated anemia, female hematocrit level, immature erythrocyte percentage, and feces and plasma pigment levels during egg laying to find out the possible origin of eggshell pigments. We found no significant effects of hematocrit level or experimentally elevated anemia on intensity of eggshell blue-green and brown pigmentations; therefore, we consider it less likely that eggshell pigments are derived from erythrocytes. In addition, we found no significant associations between female feces biliverdin concentration during egg laying and intensity of eggshell blue-green pigmentation, suggesting that eggshell biliverdin may not originate from the spleen or liver. We found a negative association between plasma and feces protoporphyrin concentrations during egg laying and eggshell brown chroma. This result suggests that an increased production of protoporphyrin in the liver, which could have elevated plasma and feces protoporphyrin concentrations, could inhibit eggshell protoporphyrin pigmentation, probably through affecting enzymatic activities. We suggest that both pigments are produced de novo in the shell gland in the canary, but circulating pigment levels may influence shell gland pigment synthesis, thus connecting the physiological status of the female to eggshell coloration.

Thermoluminescence properties of CaO powder obtained from chicken eggshells

International Nuclear Information System (INIS)

Nagabhushana, K.R.; Lokesha, H.S.; Satyanarayana Reddy, S.; Prakash, D.; Veerabhadraswamy, M.; Bhagyalakshmi, H.; Jayaramaiah, J.R.

2017-01-01

Eggshell wastage has created serious problem in disposal of the food processing industry which has been triggered the thoughts of researchers to use wasted eggshells as good source of calcium. In the present work, calcium oxide (CaO) has been synthesized by combustion process in furnace (F–CaO) and microwave oven (M–CaO) using the source of chicken eggshells. The obtained F–CaO and M–CaO are characterized by XRD, SEM with EDX and thermoluminescence (TL) technique. XRD pattern of both the samples show cubic phase with crystallite size 45–52 nm. TL glow curves are recorded for various gamma radiation dose (300–4000 Gy). Two TL glows, a small peak at 424 K and stronger peak at 597 K are observed. TL response of M–CaO is 2.67 times higher than F–CaO sample. TL kinetic parameters are calculated by computerized curve deconvolution analysis (CCDA) and discussed. - Highlights: • Calcium oxide powders have been synthesized using chicken egg shells as raw material. • Crystallite size was found to be 45–52 nm. • CaO derived from eggshells shows good thermoluminescence TL response. • TL response of the M–CaO is 2.67 times higher than the F–CaO sample.

Keeping eggs warm: thermal and developmental advantages for parasitic cuckoos of laying unusually thick-shelled eggs

Science.gov (United States)

Yang, Canchao; Huang, Qiuli; Wang, Longwu; Du, Wei-Guo; Liang, Wei; Møller, Anders Pape

2018-02-01

Obligate brood parasites have evolved unusually thick-shelled eggs, which are hypothesized to possess a variety of functions such as resistance to puncture ejection by their hosts. In this study, we tested the hypothesis that obligate brood parasites lay unusually thick-shelled eggs to retain more heat for the developing embryo and thus contribute to early hatching of parasite eggs. By doing so, we used an infrared thermal imaging system as a non-invasive method to quantify the temperature of eggshells of common cuckoos ( Cuculus canorus) and their Oriental reed warbler ( Acrocephalus orientalis) hosts in an experiment that artificially altered the duration of incubation. Our results showed that cuckoo eggshells had higher temperature than host eggs during incubation, but also less fluctuations in temperature during incubation disturbance. Therefore, there was a thermal and hence a developmental advantage for brood parasitic cuckoos of laying thick-shelled eggs, providing another possible explanation for the unusually thick-shelled eggs of obligate brood parasites and earlier hatching of cuckoo eggs compared to those of the host.

Keeping eggs warm: thermal and developmental advantages for parasitic cuckoos of laying unusually thick-shelled eggs.

Science.gov (United States)

Yang, Canchao; Huang, Qiuli; Wang, Longwu; Du, Wei-Guo; Liang, Wei; Møller, Anders Pape

2018-01-02

Obligate brood parasites have evolved unusually thick-shelled eggs, which are hypothesized to possess a variety of functions such as resistance to puncture ejection by their hosts. In this study, we tested the hypothesis that obligate brood parasites lay unusually thick-shelled eggs to retain more heat for the developing embryo and thus contribute to early hatching of parasite eggs. By doing so, we used an infrared thermal imaging system as a non-invasive method to quantify the temperature of eggshells of common cuckoos (Cuculus canorus) and their Oriental reed warbler (Acrocephalus orientalis) hosts in an experiment that artificially altered the duration of incubation. Our results showed that cuckoo eggshells had higher temperature than host eggs during incubation, but also less fluctuations in temperature during incubation disturbance. Therefore, there was a thermal and hence a developmental advantage for brood parasitic cuckoos of laying thick-shelled eggs, providing another possible explanation for the unusually thick-shelled eggs of obligate brood parasites and earlier hatching of cuckoo eggs compared to those of the host.

Influence of core thickness and artificial aging on the biaxial flexural strength of different all-ceramic materials: An in-vitro study.

Science.gov (United States)

Dikicier, Sibel; Ayyildiz, Simel; Ozen, Julide; Sipahi, Cumhur

2017-05-31

The purpose of this study was to investigate the flexural strength of all-ceramics with varying core thicknesses submitted to aging. In-Ceram Alumina (IC), IPS e.max Press (EM) and Katana (K) (n=40), were selected. Each group contained two core groups based on the core thickness as follows: IC/0.5, IC/0.8, EM/0.5, EM/0.8, K/0.5 and K/0.8 mm in thickness (n=20 each). Ten specimens from each group were subjected to aging and all specimens were tested for strength in a testing machine either with or without being subjected aging. The mean strength of the K were higher (873.05 MPa) than that of the IC (548.28 MPa) and EM (374.32 MPa) regardless of core thickness. Strength values increased with increasing core thickness for all IC, EM and K regardless of aging. Results of this study concluded that strength was not significantly affected by aging. Different core thicknesses affected strength of the all-ceramic materials tested (p<0.05).

The role of python eggshell permeability dynamics in a respiration-hydration trade-off.

Science.gov (United States)

Stahlschmidt, Zachary R; Heulin, Benoit; DeNardo, Dale F

2010-01-01

Parental care is taxonomically widespread because it improves developmental conditions and thus fitness of offspring. Although relatively simplistic compared with parental behaviors of other taxa, python egg-brooding behavior exemplifies parental care because it mediates a trade-off between embryonic respiration and hydration. However, because egg brooding increases gas-exchange resistance between embryonic and nest environments and because female pythons do not adjust their brooding behavior in response to the increasing metabolic requirements of developing offspring, python egg brooding imposes hypoxic costs on embryos during the late stages of incubation. We conducted a series of experiments to determine whether eggshells coadapted with brooding behavior to minimize the negative effects of developmental hypoxia. We tested the hypotheses that python eggshells (1) increase permeability over time to accommodate increasing embryonic respiration and (2) exhibit permeability plasticity in response to chronic hypoxia. Over incubation, we serially measured the atomic and structural components of Children's python (Antaresia childreni) eggshells as well as in vivo and in vitro gas exchange across eggshells. In support of our first hypothesis, A. childreni eggshells exhibited a reduced fibrous layer, became more permeable, and facilitated greater gas exchange as incubation progressed. Our second hypothesis was not supported, as incubation O(2) concentration did not affect the shells' permeabilities to O(2) and H(2)O vapor. Our results suggest that python eggshell permeability changes during incubation but that the alterations over time are fixed and independent of environmental conditions. These findings are of broad evolutionary interest because they demonstrate that, even in relatively simple parental-care models, successful parent-offspring relationships depend on adjustments made by both the parent (i.e., egg-brooding behavioral shifts) and the offspring (i

Freestanding eggshell membrane-based electrodes for high-performance supercapacitors and oxygen evolution reaction.

Science.gov (United States)

Geng, Jing; Wu, Hao; Al-Enizi, Abdullah M; Elzatahry, Ahmed A; Zheng, Gengfeng

2015-09-14

A type of freestanding, light-weight eggshell membrane-based electrode is demonstrated for supercapacitors and for oxygen evolution reaction (OER) catalysis. As a widely available daily waste, eggshell membranes have unique porous three-dimensional grid-like fibrous structures with relatively high surface area and abundant macropores, allowing for effective conjugation of carbon nanotubes and growth of NiCo2O4 nanowire arrays, an effective supercapacitor material and OER catalyst. The three-dimensional fibrous eggshell membrane frameworks with carbon nanotubes offer efficient pathways for charge transport, and the macropores between adjacent fibers are fully accessible for electrolytes and bubble evolution. As a supercapacitor, the eggshell membrane/carbon nanotube/NiCo2O4 electrode shows high specific capacitances at current densities from 1 to 20 A g(-1), with excellent capacitance retention (>90%) at 10 A g(-1) for over 10,000 cycles. When employed as an OER catalyst, this eggshell membrane-based electrode exhibits an OER onset potential of 1.53 V vs. the reversible hydrogen electrode (RHE), and a stable catalytic current density of 20 mA cm(-2) at 1.65 V vs. the RHE.

Application of eggshell waste for the immobilization of cadmium and lead in a contaminated soil.

Science.gov (United States)

Ok, Yong Sik; Lee, Sang Soo; Jeon, Weon-Tai; Oh, Sang-Eun; Usman, Adel R A; Moon, Deok Hyun

2011-01-01

Liming materials have been used to immobilize heavy metals in contaminated soils. However, no studies have evaluated the use of eggshell waste as a source of calcium carbonate (CaCO₃) to immobilize both cadmium (Cd) and lead (Pb) in soils. This study was conducted to evaluate the effectiveness of eggshell waste on the immobilization of Cd and Pb and to determine the metal availability following various single extraction techniques. Incubation experiments were conducted by mixing 0-5% powdered eggshell waste and curing the soil (1,246 mg Pb kg⁻¹ soil and 17 mg Cd kg⁻¹ soil) for 30 days. Five extractants, 0.01 M calcium chloride (CaCl₂), 1 M CaCl₂, 0.1 M hydrochloric acid (HCl), 0.43 M acetic acid (CH₃COOH), and 0.05 M ethylendiaminetetraacetic acid (EDTA), were used to determine the extractability of Cd and Pb following treatments with CaCO₃ and eggshell waste. Generally, the extractability of Cd and Pb in the soils decreased in response to treatments with CaCO₃ and eggshell waste, regardless of extractant. Using CaCl₂ extraction, the lowest Cd concentration was achieved upon both CaCO₃ and eggshell waste treatments, while the lowest Pb concentration was observed using HCl extraction. The highest amount of immobilized Cd and Pb was extracted by CH₃COOH or EDTA in soils treated with CaCO₃ and eggshell waste, indicating that remobilization of Cd and Pb may occur under acidic conditions. Based on the findings obtained, eggshell waste can be used as an alternative to CaCO₃ for the immobilization of heavy metals in soils.

[Effect of core: dentin thickness ratio on the flexure strength of IPS Empress II heat-pressed all-ceramic restorative material].

Science.gov (United States)

Liu, Yi-hong; Feng, Hai-lan; Bao, Yi-wang; Qiu, Yan

2007-02-18

To evaluate the effect of core:dentin thickness ratio on the flexure strength, fracture mode and origin of bilayered IPS Empress II ceramic composite specimens. IPS Empress II core ceramic, dentin porcelain and bilayered composite specimens with core:dentin thickness ratio of 2:1 and 1:1 were tested in three-point flexure strength. Mean strengths and standard deviations were determined. The optical microscopy was employed for identification of the fracture mode and origin. The flexure strength of dentin porcelain was the smallest(62.7 MPa), and the strength of bilayered composite specimens was smaller than single-layered core ceramic(190.2 MPa). The core: dentin ratio did not influence the strength of bilayered composite specimens. The frequency of occurrence of bilayered specimen delaminations was higher in the group of core: dentin thickness ratio of 1:1 than in the group of 2:1. IPS Empress II core ceramic was significantly stronger than veneering dentin porcelain. Core:dentin thickness ratio could significantly influence the fracture mode and origin, and bilayered IPS Empress II ceramic composite specimens showed little influence in the fracture strength.

The impact of eggshell colour and spot area in Japanese quails: II. Slaughter and carcass characteristic

Directory of Open Access Journals (Sweden)

Sema Alasahan

Full Text Available ABSTRACT This study was carried out to investigate the effects of eggshell colour and spot properties (colour and size of the spot area on growth performance and carcass traits of Japanese quail (Coturnix coturnix japonica eggs. Study material were allocated to five groups according to their eggshell and spot colours: black spots on greyish white coloured eggshell (I, blue spots on greyish white coloured eggshell (II, diffuse brown spots on greyish brown coloured eggshell (III, brown spots on light green colored eggshell (IV, and small brown spots on greyish brown coloured eggshell (V. The size of the spotted area was determined in each egg group using digital image analysis. The groups did not differ for body weight and length of the shank at the end of the growth period. However, the groups differed significantly for carcass yield after slaughter (not eviscerated and carcass yield. These parameters were highest in Group I (82.08 and 76.09% and lowest in Group III (80.20 and 73.86%. Digital image analysis demonstrated that heart length, cardiac fat area, gizzard width, and intestine length varied between the groups. Cardiac fat area was largest in Group III (0.86 cm2 and smallest in Group V (0.65 cm2. Gizzard width was greatest in Group I (2.63 cm and smallest in Group V (2.47 cm. Intestine length was greatest in Group V (78.45 cm and smallest in Group IV (72.39 cm. Body weight, shank length, and slaughter and carcass weight do not vary in relation to eggshell colour or the size of the spotted area. The lengths of intestine and heart, gizzard width, and cardiac fat area do vary in relation to eggshell colour or the size of the spotted area.

Strontium-90 in Canada goose eggshells: Nonfatal monitoring for contamination in wildlife

International Nuclear Information System (INIS)

Rickard, W.H.; Eberhardt, L.E.

1990-01-01

90 Sr was measured in eggshells from Canada geese (Branta canadensis moffitti) that nested on Columbia River islands up- and downstream from deactivated plutonium production reactors on the U.S. Department of Energy's Hanford Site in southeastern Washington. We also measured 90 Sr in wing bones of goose carcasses. Background levels of 90 Sr were based on eggshells collected on an island upstream of the reactors. A few eggshells collected from nests on a single island downstream of the reactors had slightly higher than background levels of 90 Sr. This may have resulted from geese eating shoreline plants or crops irrigated with Columbia River water that contained 90 Sr released into the river through groundwater seepage

Thermoluminescence properties of CaO powder obtained from chicken eggshells

Science.gov (United States)

Nagabhushana, K. R.; Lokesha, H. S.; Satyanarayana Reddy, S.; Prakash, D.; Veerabhadraswamy, M.; Bhagyalakshmi, H.; Jayaramaiah, J. R.

2017-09-01

Eggshell wastage has created serious problem in disposal of the food processing industry which has been triggered the thoughts of researchers to use wasted eggshells as good source of calcium. In the present work, calcium oxide (CaO) has been synthesized by combustion process in furnace (F-CaO) and microwave oven (M-CaO) using the source of chicken eggshells. The obtained F-CaO and M-CaO are characterized by XRD, SEM with EDX and thermoluminescence (TL) technique. XRD pattern of both the samples show cubic phase with crystallite size 45-52 nm. TL glow curves are recorded for various gamma radiation dose (300-4000 Gy). Two TL glows, a small peak at 424 K and stronger peak at 597 K are observed. TL response of M-CaO is 2.67 times higher than F-CaO sample. TL kinetic parameters are calculated by computerized curve deconvolution analysis (CCDA) and discussed.

The effect of wall thickness distribution on mechanical reliability and strength in unidirectional porous ceramics

Science.gov (United States)

Seuba, Jordi; Deville, Sylvain; Guizard, Christian; Stevenson, Adam J.

2016-01-01

Macroporous ceramics exhibit an intrinsic strength variability caused by the random distribution of defects in their structure. However, the precise role of microstructural features, other than pore volume, on reliability is still unknown. Here, we analyze the applicability of the Weibull analysis to unidirectional macroporous yttria-stabilized-zirconia (YSZ) prepared by ice-templating. First, we performed crush tests on samples with controlled microstructural features with the loading direction parallel to the porosity. The compressive strength data were fitted using two different fitting techniques, ordinary least squares and Bayesian Markov Chain Monte Carlo, to evaluate whether Weibull statistics are an adequate descriptor of the strength distribution. The statistical descriptors indicated that the strength data are well described by the Weibull statistical approach, for both fitting methods used. Furthermore, we assess the effect of different microstructural features (volume, size, densification of the walls, and morphology) on Weibull modulus and strength. We found that the key microstructural parameter controlling reliability is wall thickness. In contrast, pore volume is the main parameter controlling the strength. The highest Weibull modulus (?) and mean strength (198.2 MPa) were obtained for the samples with the smallest and narrowest wall thickness distribution (3.1 ?m) and lower pore volume (54.5%).

Adsorbed polymers in aqueous media. The relation between zeta-potential, layer thickness and ionic strength

NARCIS (Netherlands)

Cohen Stuart, M.A.; Mulder, J.W.

1985-01-01

Streaming potentials for glass capillaries with and without adsorbed poly(vinyl pyrrolidone) were used to determine the thickness of the adsorbed polymer layer. It was found that the thickness determined in this way is a strong function of the ionic strength of the solution. The results are compared

Utilization of calcium carbonate particles from eggshell waste as coating pigments for ink-jet printing paper.

Science.gov (United States)

Yoo, Sukjoon; Hsieh, Jeffery S; Zou, Peter; Kokoszka, John

2009-12-01

The effective treatment and utilization of biowaste have been emphasized in our society for environmental and economic concerns. Recently, the eggshell waste in the poultry industry has been highlighted because of its reclamation potential. This study presents an economical treatment process to recover useful bioproducts from eggshell waste and their utilization in commercial products. We developed the dissolved air floatation (DAF) separation unit, which successfully recovered 96% of eggshell membrane and 99% of eggshell calcium carbonate (ECC) particles from eggshell waste within 2 h of operation. The recovered ECC particles were utilized as coating pigments for ink-jet printing paper and their impact on the ink density and paper gloss were investigated. The addition of the ECC particles as coating pigments enhances the optical density of cyan, magenta and yellow inks while decreasing the black ink density and the gloss of the coated paper.

Incubation reduces microbial growth on eggshells and the opportunity for trans-shell infection.

Science.gov (United States)

Mark I. Cook; Steven R. Beissinger; Gary A. Toranzos; Wayne J. Arendt

2005-01-01

Avian eggshells harbour microbes shortly after laying, and under appropriate ambient conditions they can multiply rapidly, penetrate through shell pores, infect egg contents and cause embryo mortality. We experimentally examined how incubation affects bacterial processes on the eggshells of pearl-eyed thrashers Margarops fuscatus nesting in tropical montane and lowland...

Relationship between macular thickness measurement and signal strength using Stratus optical coherence tomography

OpenAIRE

Segal, Ori; Shapira, Yinon; Gershoni, Assaf; Vainer, Igor; Nemet, Arie Y; Geffen, Noa; Mimouni, Michael

2016-01-01

Ori Segal,1 Yinon Shapira,2 Assaf Gershoni,1 Igor Vainer,2 Arie Y Nemet,1 Noa Geffen,1 Michael Mimouni2 1Department of Ophthalmology, Meir Medical Center, Kfar Saba, Israel and the Sackler School of Medicine, Tel Aviv University, Tel Aviv, 2Department of Ophthalmology, Rambam Health Care Campus, Haifa, Israel Purpose: To examine the relationship between signal strength and macular thickness as measured by Stratus optical coherence tomography (OCT)’s fast macular thickness protocol...

iTRAQ-Based Quantitative Proteomics Identifies Potential Regulatory Proteins Involved in Chicken Eggshell Brownness.

Directory of Open Access Journals (Sweden)

Guangqi Li

Full Text Available Brown eggs are popular in many countries and consumers regard eggshell brownness as an important indicator of egg quality. However, the potential regulatory proteins and detailed molecular mechanisms regulating eggshell brownness have yet to be clearly defined. In the present study, we performed quantitative proteomics analysis with iTRAQ technology in the shell gland epithelium of hens laying dark and light brown eggs to investigate the candidate proteins and molecular mechanisms underlying variation in chicken eggshell brownness. The results indicated 147 differentially expressed proteins between these two groups, among which 65 and 82 proteins were significantly up-regulated in the light and dark groups, respectively. Functional analysis indicated that in the light group, the down-regulated iron-sulfur cluster assembly protein (Iba57 would decrease the synthesis of protoporphyrin IX; furthermore, the up-regulated protein solute carrier family 25 (mitochondrial carrier; adenine nucleotide translocator, member 5 (SLC25A5 and down-regulated translocator protein (TSPO would lead to increased amounts of protoporphyrin IX transported into the mitochondria matrix to form heme with iron, which is supplied by ovotransferrin protein (TF. In other words, chickens from the light group produce less protoporphyrin IX, which is mainly used for heme synthesis. Therefore, the exported protoporphyrin IX available for eggshell deposition and brownness is reduced in the light group. The current study provides valuable information to elucidate variation of chicken eggshell brownness, and demonstrates the feasibility and sensitivity of iTRAQ-based quantitative proteomics analysis in providing useful insights into the molecular mechanisms underlying brown eggshell pigmentation.

Engineering Tough Materials: Biomimetic Eggshell

Science.gov (United States)

2016-08-29

Fellow Dr. David Labonte Cambridge University Engineering Dept., Trumpington Street, Cambridge CB2 1PZ, UK ~ Approved for public release; distribution...with a brief outlook, including next steps to pursue in the new cooperative research arrangement between ERDC and the University of Cambridge . Summary...HCl in 2 h at room temperature. Shell & Membrane Shell Outer membrane Inner membrane Figure 1: Cross section of an eggshell illustrating the direct

Immobilisation of lead and zinc in contaminated soil using compost derived from industrial eggshell.

Science.gov (United States)

Soares, Micaela A R; Quina, Margarida J; Quinta-Ferreira, Rosa M

2015-12-01

This study aims to evaluate the capacity of a compost obtained by co-composting of industrial eggshell (CES) to immobilise lead (Pb) and zinc (Zn) in an acidic soil contaminated by mining activities. Mature compost without eggshell (CWES) and natural eggshell (ES) were also tested as soil amendments for comparison purposes. Three different application rates were used for each material, ensuring the same quantity in terms of neutralizing capacity. Incubation experiments were conducted under controlled conditions and CO2 emissions monitored for 94 days. The environmental availability of Pb and Zn in the amended soil was assessed and bioassays were performed at the end of the incubation period. When eggshells were present, the CES compost raised the soil pH to values higher than 6 and reduced the soil mobile fraction for both Pb and Zn, in more than 95%. Soil toxicity towards Vibrio fischeri was also suppressed and environmental risk decreased to "low level". However, the immobilisation in the acid insoluble soil component was significantly achieved only for Zn. In addition, regarding soil carbon dynamics the CO2-C emissions were enhanced, mainly in the case of the highest rate of amendment. Both first order-E and parallel first order models may adequately describe the kinetic data of CO2-C cumulative release. Without eggshells, the CWES compost revealed limited effect on heavy metals immobilisation, likely due to its small capacity to correct soil acidity, at lower application rates. Using solely eggshells, the ES waste had similar outcomes when compared with CES, but at the higher application rate, CO2 emissions were enhanced with the eggshell compost due to the contribution of biotic carbon present therein. Therefore, this study points out that CES is an effective liming material and may be used for in situ remediation of contaminated soil with Pb and Zn. Copyright © 2015 Elsevier Ltd. All rights reserved.

Oxygen isotope fractionation between bird eggshell calcite and body water: application to fossil eggs from Lanzarote (Canary Islands)

Science.gov (United States)

Lazzerini, Nicolas; Lécuyer, Christophe; Amiot, Romain; Angst, Delphine; Buffetaut, Eric; Fourel, François; Daux, Valérie; Betancort, Juan Francisco; Flandrois, Jean-Pierre; Marco, Antonio Sánchez; Lomoschitz, Alejandro

2016-10-01

Oxygen and carbon isotope compositions of fossil bird eggshell calcite (δ18Ocalc and δ13Ccalc) are regularly used to reconstruct paleoenvironmental conditions. However, the interpretation of δ18Ocalc values of fossil eggshells has been limited to qualitative variations in local climatic conditions as oxygen isotope fractionations between calcite, body fluids, and drinking water have not been determined yet. For this purpose, eggshell, albumen water, and drinking water of extant birds have been analyzed for their oxygen and carbon isotope compositions. Relative enrichments in 18O relative to 16O between body fluids and drinking water of +1.6 ± 0.9 ‰ for semi-aquatic birds and of +4.4 ± 1.9 ‰ for terrestrial birds are observed. Surprisingly, no significant dependence to body temperature on the oxygen isotope fractionation between eggshell calcite and body fluids is observed, suggesting that bird eggshells precipitate out of equilibrium. Two empirical equations relating the δ18Ocalc value of eggshell calcite to the δ18Ow value of ingested water have been established for terrestrial and semi-aquatic birds. These equations have been applied to fossil eggshells from Lanzarote in order to infer the ecologies of the Pleistocene marine bird Puffinus sp. and of the enigmatic giant birds from the Pliocene. Both δ13Ccalc and δ18Ocalc values of Puffinus eggshells point to a semi-aquatic marine bird ingesting mostly seawater, whereas low δ13Ccalc and high δ18Ocalc values of eggshells from the Pliocene giant bird suggest a terrestrial lifestyle. This set of equations can help to quantitatively estimate the origin of waters ingested by extinct birds as well as to infer either local environmental or climatic conditions.

Heavy metal immobilization in soil near abandoned mines using eggshell waste and rapeseed residue.

Science.gov (United States)

Lee, Sang Soo; Lim, Jung Eun; El-Azeem, Samy A M Abd; Choi, Bongsu; Oh, Sang-Eun; Moon, Deok Hyun; Ok, Yong Sik

2013-03-01

Heavy metal contamination of agricultural soils has received great concern due to potential risk to human health. Cadmium and Pb are largely released from abandoned or closed mines in Korea, resulting in soil contamination. The objective of this study was to evaluate the effects of eggshell waste in combination with the conventional nitrogen, phosphorous, and potassium fertilizer (also known as NPK fertilizer) or the rapeseed residue on immobilization of Cd and Pb in the rice paddy soil. Cadmium and Pb extractabilities were tested using two methods of (1) the toxicity characteristics leaching procedure (TCLP) and (2) the 0.1 M HCl extraction. With 5 % eggshell addition, the values of soil pH were increased from 6.33 and 6.51 to 8.15 and 8.04 in combination with NPK fertilizer and rapeseed residue, respectively, compared to no eggshell addition. The increase in soil pH may contribute to heavy metal immobilization by altering heavy metals into more stable in soils. Concentrations of TCLP-extracted Cd and Pb were reduced by up to 67.9 and 93.2 % by addition of 5 % eggshell compared to control. For 0.1 M HCl extraction method, the concentration of 0.1 M HCl-Cd in soils treated with NPK fertilizer and rapeseed residue was significantly reduced by up to 34.01 and 46.1 %, respectively, with 5 % eggshell addition compared to control. A decrease in acid phosphatase activity and an increase in alkaline phosphatase activity at high soil pH were also observed. Combined application of eggshell waste and rapeseed residue can be cost-effective and beneficial way to remediate the soil contaminated with heavy metals.

Vibration properties of the ostrich eggshell at impact

Czech Academy of Sciences Publication Activity Database

Trnka, Jan; Stoklasová, Pavla; Strnková, J.; Nedomová, Š.; Buchar, J.

2013-01-01

Roč. 61, č. 6 (2013), s. 1873-1880 ISSN 1211-8516 Institutional support: RVO:61388998 Keywords : eggshell * impact * surface displacement Subject RIV: GM - Food Processing http://acta.mendelu.cz/61/6/1873/same_authors/

Applicability of newly developed 610MPa class heavy thickness high strength steel to boiler pressure vessel

Energy Technology Data Exchange (ETDEWEB)

Katayama, Norihiko; Kaihara, Shoichiro; Ishii, Jun [Ishikawajima-Harima Heavy Industries Corp., Yokohama (Japan); Kajigaya, Ichiro [Ishikawajima-Harima Heavy Industries Corp., Tokyo (Japan); Totsuka, Takehiro; Miyazaki, Takashi [Ishikawajima-Harima Heavy Industries Corp., Aioi (Japan)

1995-11-01

Construction of a 350 MW Class PFBC (Pressurized Fluidized Bed Combustion) boiler plant is under planning in Japan. Design temperature and pressure of the vessel are maximum 350 C and 1.69 MPa, respectively. As the plate thickness of the vessel exceeds over 100 mm, high strength steel plate of good weldability and less susceptible to reheat cracking was required and developed. The steel was aimed to satisfy the tensile strength over 610 MPa at 350 C after postweld heat treatment (PWHT), with good notch toughness. The authors investigated the welding performances of the newly developed steel by using 150 mm-thick plate welded by pulsed-MAG and SAW methods. It was confirmed that the newly developed steel and its welds possess sufficient strength and toughness after PWHT, and applicable to the actual pressure vessel.

Physico-mechanical and structural properties of eggshell membrane gelatin- chitosan blend edible films

DEFF Research Database (Denmark)

Mohammadi, Reza; Mohammadifar, Mohammad Amin; Rouhi, Milad

2018-01-01

This study investigated the physico-mechanical and structural properties of composite edible films based on eggshell membrane gelatin (G) and chitosan (Ch) (75G:25Ch, 50G:50Ch, 25G:75Ch). The results demonstrated that the addition of Ch increased elongation at break significantly (p< 0.05), but r......This study investigated the physico-mechanical and structural properties of composite edible films based on eggshell membrane gelatin (G) and chitosan (Ch) (75G:25Ch, 50G:50Ch, 25G:75Ch). The results demonstrated that the addition of Ch increased elongation at break significantly (p... interactions introduced by the addition of chitosan to eggshell membrane gelatin as new resources could improve the films’ functional properties....

The effect of different dietary vitamin and mineral levels on certain ...

African Journals Online (AJOL)

Tesselaar, Ger-Mari

2014-08-24

Aug 24, 2014 ... monocalcium phosphate added as phosphorus source, (vii) with a normal ... period on the production of breeding ostriches. ... The main factor affecting the strength of the hen eggshell is the thickness of the shell (Romanhoff &.

The influence of lay-up and thickness on composite impact damage and compression strength

Science.gov (United States)

Guynn, E. G.; Obrien, T. K.

1985-01-01

The effects of composite stacking sequence, thickness, and percentage of zero-degree plies on the size, shape, and distribution of delamination through the laminate thickness and on residual compression strength following impact were studied. Graphite/epoxy laminates were impacted with an 0.5 inch diameter aluminum sphere at a specific low or high velocity. Impact damage was measured nondestructively by ultrasonic C-scans and X-radiography and destructively by the deply technique, and compression strength tests were performed. It was found that differences in compression failure strain due to stacking sequence were small, while laminates with very low percentages of zero-degree plies had similar failure loads but higher failure strains than laminates with higher percentages of zero-degree plies. Failure strain did not correlate with planar impact damage area, and delaminations in impact regions were associated with matrix cracking.

Palm Oil Fuel Ash (POFA and Eggshell Powder (ESP as Partial Replacement for Cement in Concrete

Directory of Open Access Journals (Sweden)

Mohamad Mazizah Ezdiani

2018-01-01

Full Text Available This study is an attempt to partially replace Ordinary Portland cement (OPC in concrete with palm oil fuel ash (POFA and eggshell powder (ESP. The mix proportions of POFA and ESP were varied at 10% of cement replacement and compared with OPC concrete as control specimen. The fineness of POFA is characterized by passing through 300 μm sieve and ESP by passing through 75 μm sieve. Compressive strength testing was conducted on concrete specimens to determine the optimum mix proportion of POFA and ESP. Generally the compressive strength of OPC concrete is higher compared to POFA-ESP concrete. Based on the results of POFA-ESP concrete overall, it shows that the optimum mix proportion of concrete is 6%POFA:4% ESP achieved compressive strength of 38.60 N/mm2 at 28 days. The compressive strength of OPC concrete for the same period was 42.37 N/mm2. Higher water demand in concrete is needed due to low fineness of POFA that contributing to low compressive strength of POFA-ESP concrete. However, the compressive strength and workability of the POFA-ESP concrete were within the ranges typically encountered in regular concrete mixtures indicating the viability of this replacement procedure for structural and non-structural applications.

Palm Oil Fuel Ash (POFA) and Eggshell Powder (ESP) as Partial Replacement for Cement in Concrete

Science.gov (United States)

Ezdiani Mohamad, Mazizah; Mahmood, Ali A.; Min, Alicia Yik Yee; Nur Nadhira A., R.

2018-03-01

This study is an attempt to partially replace Ordinary Portland cement (OPC) in concrete with palm oil fuel ash (POFA) and eggshell powder (ESP). The mix proportions of POFA and ESP were varied at 10% of cement replacement and compared with OPC concrete as control specimen. The fineness of POFA is characterized by passing through 300 μm sieve and ESP by passing through 75 μm sieve. Compressive strength testing was conducted on concrete specimens to determine the optimum mix proportion of POFA and ESP. Generally the compressive strength of OPC concrete is higher compared to POFA-ESP concrete. Based on the results of POFA-ESP concrete overall, it shows that the optimum mix proportion of concrete is 6%POFA:4% ESP achieved compressive strength of 38.60 N/mm2 at 28 days. The compressive strength of OPC concrete for the same period was 42.37 N/mm2. Higher water demand in concrete is needed due to low fineness of POFA that contributing to low compressive strength of POFA-ESP concrete. However, the compressive strength and workability of the POFA-ESP concrete were within the ranges typically encountered in regular concrete mixtures indicating the viability of this replacement procedure for structural and non-structural applications.

The relationship between the density of Aedes vigilax (Diptera: Culicidae) eggshells and environmental factors on Kooragang Island, New South Wales, Australia.

Science.gov (United States)

Turner, P A; Streever, W J

1997-12-01

Knowledge of oviposition sites selected by wetland mosquitoes could improve mosquito control and guide wetland rehabilitation practices to avoid creating or exacerbating a mosquito problem. Two studies that enumerated Aedes vigilax eggshells found in salt marsh soil on the western portion of Kooragang Island in New South Wales, Australia, allowed an evaluation of oviposition sites. In one study, the density of eggshells found in samples collected from a large area was related to environmental factors, including distance from nearby drainage channels, vegetation cover, elevation, and terrain characteristics. Multiple-regression analysis suggested eggshell densities were positively correlated with the presence of depressions and ponds, vegetation cover, and distance from culverts, but negatively related to elevation. In another study, eggshell density was related to relative elevation and vegetation species within each of two 400-m2 plots on Kooragang Island. In all but one instance, samples from bare soil contained fewer eggshells than samples with vegetation cover at both plots. Eggshell density did not differ between the two dominant vegetation species, Sarcocornia quinqueflora and Sporobolus virginicus, although bare soil of one plot had a mean eggshell density similar to that of soil with S. quinqueflora cover. Eggshells were at highest density at intermediate elevations at one plot but at low elevations at the other.

Eggshell powder, a comparable or better source of calcium than purified calcium carbonate: Piglet studies

NARCIS (Netherlands)

Schaafsma, A.; Beelen, G.M.

1999-01-01

Powdered chicken eggshells might be an interesting and widely available source of calcium. In two studies using piglets we determined the digestibility of calcium from different diets. The first study compared casein-based diets with CaCO3 (CasCC) or eggshell powder (CasES). The second study

A study on the relationship between iridium concentration in hen eggshell and iridium-enriched feed by NAA

International Nuclear Information System (INIS)

Yang Gaochuang; Mao Xueying; Wang Jinchun; Lu Yali; Ouyang Hong; Zhang Zhaohui; Chai Zhifang

2001-01-01

Four hens were fed by adding ammonium hexachloroiridate into their forage. After two weeks, Ir concentration in three fractions (eggshell, albumen, egg yolk) of their eggs were measured by instrumental neutron activation analysis (INAA). Ir was present in all the three parts of the eggs. Further, the highest concentration of Ir was found in the egg yolk fraction, about 10 times higher than that in the eggshell and albumen. Moreover, the longer the Ir-containing feed was used, the higher the Ir concentration in the egg fractions was. After 4-6 day feeding, the Ir concentration became stable. The experimental results indicated that the Ir concentration was about 2-7 x 10 -10 g/g in the eggshell fraction compared to 5.6 x 10 -7 g/g in feed. Therefore, the ratio from the feed over the eggshell via gastrointestinal pathway was estimated to be about 0.08%. The new result is useful to evaluate the iridium-enriched eggshell fossils of dinosauria and to interpret the origin of the mass extinction of dinosauria at the end of Cretaceous. (author)

Antimicrobial properties of a nanostructured eggshell from a compost-nesting bird.

Science.gov (United States)

D'Alba, Liliana; Jones, Darryl N; Badawy, Hope T; Eliason, Chad M; Shawkey, Matthew D

2014-04-01

Infection is an important source of mortality for avian embryos but parental behaviors and eggs themselves can provide a network of antimicrobial defenses. Mound builders (Aves: Megapodiidae) are unique among birds in that they produce heat for developing embryos not by sitting on eggs but by burying them in carefully tended mounds of soil and microbially decomposing vegetation. The low infection rate of eggs of one species in particular, the Australian brush-turkey (Alectura lathami), suggests that they possess strong defensive mechanisms. To identify some of these mechanisms, we first quantified antimicrobial albumen proteins and characterized eggshell structure, finding that albumen was not unusually antimicrobial, but that eggshell cuticle was composed of nanometer-sized calcite spheres. Experimental tests revealed that these modified eggshells were significantly more hydrophobic and better at preventing bacterial attachment and penetration into the egg contents than chicken eggs. Our results suggest that these mechanisms may contribute to the antimicrobial defense system of these eggs, and may provide inspiration for new biomimetic anti-fouling surfaces.

Eggshell appearance does not signal maternal corticosterone exposure in Japanese quail: an experimental study with brown-spotted eggs.

Directory of Open Access Journals (Sweden)

Camille Duval

Full Text Available Reproduction is a critical period for birds as they have to cope with many stressful events. One consequence of an acute exposure to stress is the release of corticosterone, the avian stress hormone. Prolonged stress can have negative impacts on the immune system, resulting in, for example, increased oxidative stress. Through maternal effects, females are known to modulate their investment in eggs content according to their own physiological condition. Less is known about maternal investment in eggshells, especially in pigments. The two main eggshell pigments may possess opposite antioxidant properties: protoporphyrin (brown is a pro-oxidant, whereas biliverdin (blue-green is an antioxidant. In Japanese quail, we know that the deposition of both pigments is related to female body condition. Thus, a chronic stress response may be reflected in eggshell coloration. Using female Japanese quails that lay brown-spotted eggs, we explored whether physiological exposure to corticosterone induces a change in female basal stress and antioxidant factors, and eggshell pigment concentration, spectrophotometric reflectance, and maculation coverage. We supplemented adult females over a 2 week period with either peanut oil (control or corticosterone (treatment. We collected pre- and post-supplementation eggs and analysed the effect of corticosterone treatment on female physiology and eggshell appearance parameters. Except for corticosterone-fed birds which laid eggs with brighter spots, supplementation had no significant effect on female physiology or eggshell pigment concentration, reflectance and maculation. The change in eggshell spot brightness was not detected by a photoreceptor noise-limited color opponent model of avian visual perception. Our data confirms that eggshell reflectance in spotted eggs varies over the laying sequence, and spot reflectance may be a key factor that is affected by females CORT exposure, even if the changes are not detected by an

The influence of chicken eggshell powder as a buffer on biohydrogen production from rotten orange (Citrus nobilis var. microcarpa) with immobilized mixed culture

Science.gov (United States)

Damayanti, Astrilia; Sarto, Syamsiah, Siti; Sediawan, Wahyudi B.

2017-06-01

This research observed the influence of chicken eggshell on hydrogen production from anaerobic fermentation of rotten orange (Citrus nobilis var. microcarpa) using batch method at 36 °C and pH 7. Fermentation material were varied in several types, the first type was meat and peel of oranges with VS of 59.152 g.L-1 in A, B, C, and D compositions. The second type was orange meat added with peel (OMP) with VS of 36.852 g.L-1. The immobilized ingredients used in the experiment consisted of 2 % (w/v) alginate and active carbon with the ratio of 1:1. 3.2 g chicken eggshell powder was added to the first type of material (substrates A, B, C, and D). Results showed that pH during fermentation process using chicken eggshell as a buffer was constant at 5.5; however, without the use of chicken eggshell, the pH decreased to 3.8 and increased slightly before it stayed stable at 4.0. The total amount of gas produced in sample using the chicken eggshell was 46,35 mL.mg VS-1 and in sample produced without the eggshell, it was 3,4 mL.mg VS-1. The production of hydrogen in substrate that used chicken eggshell was 1,276 mL.gVS-1 in average on the first day. Meanwhile, for the substrate with no addition of chicken eggshell, the average production of hydrogen was 0,163 mL.gVS-1. The reduction of volatile solid (VS) in sample that used chicken eggshell was 24 %, while in sample produced without addition of chicken eggshell, the reduction was 12 %. The liquid compounds (VFA) produced in the fermentation using chicken eggshell were acetic acid and butyric acid. Meanwhile, without addition of chicken eggshell, the products were acetic acid, butyric acid, and propionic acid. This study shows that addition of chicken eggshell as a buffer effectively contributed to hydrogen production during fermentation of rotten oranges.

Bacteriological contamination, dirt, and cracks of eggshells in furnished cages and noncage systems for laying hens: an international on-farm comparison.

Science.gov (United States)

De Reu, K; Rodenburg, T B; Grijspeerdt, K; Messens, W; Heyndrickx, M; Tuyttens, F A M; Sonck, B; Zoons, J; Herman, L

2009-11-01

For laying hens, the effects of housing system on bacterial eggshell contamination and eggshell quality is almost exclusively studied in experimental hen houses. The aim of this study was to compare eggshell hygiene and quality under commercial conditions. Six flocks of laying hens in furnished cages and 7 flocks in noncage systems were visited when hens were about 60 wk of age. Farms from Belgium, the Netherlands, and Germany were included in the study. The following parameters were determined on eggs sampled at the egg belts: 1) bacterial eggshell contamination, as expressed by total count of aerobic bacteria and number of Enterobacteriaceae; 2) proportion of dirty eggs; and 3) proportion of cracked eggs and eggs with microcracks. Considerable within-flock differences were found in eggshell contamination with total count of aerobic bacteria, both for furnished cages (P < or = 0.001, range 4.24 to 5.22 log cfu/eggshell) and noncage systems (P < or = 0.001, range 4.35 to 5.51 log cfu/eggshell). On average, lower levels of contamination with total count of aerobic bacteria (4.75 vs. 4.98 log cfu/eggshell; P < or = 0.001) were found on eggshells from furnished cages compared with noncage systems. Concerning Enterobacteriaceae, no significant difference in average eggshell contamination between both systems could be shown. The total percentage of cracked eggs was higher (P < or = 0.01) in furnished cages (7.8%) compared with noncage systems (4.1%). This was, however, due to the high percentage of cracked eggs (24%) observed on one of the furnished cage farms. We conclude that bacteriological eggshell contamination and percentage of cracked eggs differed substantially between individual farms using the same housing system. This may also explain some discrepancies between the findings of the present study versus some findings of previous experimental studies or studies on a small number of farms. Although statistically significant, the average differences in

The Microbial Burden Load of Eggshells from Different Poultry ...

African Journals Online (AJOL)

PROF HORSFALL

In this study, the microbial load of egg shell from different poultry system in .... eggshell surface and also decrease bacterial and fungal invasion ... measures of central tendency (mean ± standard .... Salmonella Contamination and Disinfection.

Evaluation of the resin cement thicknesses and push-out bond strengths of circular and oval fiber posts in oval-shapes canals

Science.gov (United States)

Er, Özgür; Kılıç, Kerem; Kılınç, Halil İbrahim; Sağsen, Burak

2015-01-01

PURPOSE The aim of this study was to evaluate whether the push-out bond strength varies between oval and circular fiber posts, and to examine the effect on the resin cement thicknesses around the posts. MATERIALS AND METHODS Eighteen mandibular premolar roots were separated into two groups for oval and circular fiber posts systems. Post spaces were prepared and fiber posts were luted to the post spaces. Roots were cut horizontally to produce 1-mm-thick specimens. Resin cement thicknesses were determined with a metallographic optical microscope and push-out tests were done. RESULTS No significant differences were observed in terms of push-out bond strength between the oval and circular fiber posts (P>.05) The resin cement thicknesses of the oval posts were greater than those of the circular posts group in the coronal, middle and apical specimens (P<.05). CONCLUSION In the light of these results, it can be stated that resin cement thickness does not affect the push-out bond strength. PMID:25722832

Impact of egg holding temperatures on the recovery of Salmonella from eggshells and stainless steel coupons

Science.gov (United States)

This experiment was conducted to determine the impact of egg holding temperature on the ability to recover Salmonella from eggshells after 24 h. Salmonella enterica Enteritidis (nalidixic acid resistant marker strain) inoculated eggshells and stainless steel coupons (SSC, 14 mm diameter) were held a...

Influence of increment thickness on dentin bond strength and light transmission of composite base materials.

Science.gov (United States)

Omran, Tarek A; Garoushi, Sufyan; Abdulmajeed, Aous A; Lassila, Lippo V; Vallittu, Pekka K

2017-06-01

Bulk-fill resin composites (BFCs) are gaining popularity in restorative dentistry due to the reduced chair time and ease of application. This study aimed to evaluate the influence of increment thickness on dentin bond strength and light transmission of different BFCs and a new discontinuous fiber-reinforced composite. One hundred eighty extracted sound human molars were prepared for a shear bond strength (SBS) test. The teeth were divided into four groups (n = 45) according to the resin composite used: regular particulate filler resin composite: (1) G-ænial Anterior [GA] (control); bulk-fill resin composites: (2) Tetric EvoCeram Bulk Fill [TEBF] and (3) SDR; and discontinuous fiber-reinforced composite: (4) everX Posterior [EXP]. Each group was subdivided according to increment thickness (2, 4, and 6 mm). The irradiance power through the material of all groups/subgroups was quantified (MARC® Resin Calibrator; BlueLight Analytics Inc.). Data were analyzed using two-way ANOVA followed by Tukey's post hoc test. SBS and light irradiance decreased as the increment's height increased (p composite used. EXP presented the highest SBS in 2- and 4-mm-thick increments when compared to other composites, although the differences were not statistically significant (p > 0.05). Light irradiance mean values arranged in descending order were (p composites. Discontinuous fiber-reinforced composite showed the highest value of curing light transmission, which was also seen in improved bonding strength to the underlying dentin surface. Discontinuous fiber-reinforced composite can be applied safely in bulks of 4-mm increments same as other bulk-fill composites, although, in 2-mm thickness, the investigated composites showed better performance.

How the oxygen isotope ratio of rain water influences the isotope ratio of chicken eggshell carbonate

Science.gov (United States)

Price, Gregory; Grimes, Stephen

2015-04-01

The stable oxygen isotope ratio of chicken eggshell carbonate was analysed from chicken eggs laid under free range, and organic farming regimes from across the UK. The eggshell carbonate oxygen isotope data shows a clear depletion in delta18O distribution from the southwest to the northeast. Although consistently offset by around 1 permil, the same isotopic distribution as that seen in eggshell carbonate is observed in the delta18O ratio of rainfall and groundwater from across the UK. This distribution is related to the Rayleigh distillation of rainfall driven by westerly winds across the UK landmass. The clear relationship observed between eggshell delta18O values and that of rainwater presumably reflects the nature of free range chickens which must be drinking locally derived rainwater and supplementing their diet and water intake with locally derived food. These results suggest that the oxygen isotope value of chicken eggshells can be used as a forensic tool to identify the locality that free range and organic eggs were laid within the UK. Furthermore, if suitable material is preserved in the archaeological and geological record then such a relationship can potentially be used to establish the oxygen isotope value of rainwater from which ancient and / or ancestral birds lived.

Eggshell membranes as a noninvasive sampling for molecular ...

African Journals Online (AJOL)

Noninvasive sampling is of prime essential on conservation genetics and molecular ecology. It is particularly preferred to use in the genetic identification of individuals and genetic analysis. A simple and efficient sampling is described for molecular studies from eggshell membranes in an endemic population of Chinese ...

Calcined eggshell (CES): An efficient natural catalyst for ...

Indian Academy of Sciences (India)

hydes with active methylene compounds using calcined eggshell (CES) as an efficient ... of the important reactions to achieve carbon–carbon ... solid catalyst for biodiesel production,24 as a catalyst ... which supports for adsorption of water on CaO and ... The organic phase .... After extraction of the product with ethylac-.

Proteomic analysis of chicken eggshell cuticle membrane layer

Czech Academy of Sciences Publication Activity Database

Mikšík, Ivan; Ergang, Peter; Pácha, Jiří

2014-01-01

Roč. 406, č. 29 (2014), s. 7633-7640 ISSN 1618-2642 R&D Projects: GA ČR(CZ) GA13-17224S Institutional support: RVO:67985823 Keywords : mass spectrometry * bioanalyticalmethods * cuticle * chicken proteins * insoluble proteins * eggshell Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 3.436, year: 2014

Determination of insoluble avian eggshell matrix proteins

Czech Academy of Sciences Publication Activity Database

Mikšík, Ivan; Sedláková, Pavla; Lacinová, Kateřina; Pataridis, Statis; Eckhardt, Adam

2010-01-01

Roč. 397, č. 1 (2010), s. 205-214 ISSN 1618-2642 R&D Projects: GA MŠk(CZ) 1M0510; GA ČR(CZ) GA203/09/0675; GA ČR(CZ) GA203/08/1428 Institutional research plan: CEZ:AV0Z50110509 Keywords : eggshell proteins * insoluble proteins * matrix proteins Subject RIV: CE - Biochemistry Impact factor: 3.841, year: 2010

An insight into the heat and mass transfer mechanisms of eggshells hatching broiler chicks and its effects to the hatcher environment.

Science.gov (United States)

Romanini, C E B; Exadaktylos, V; Hong, S W; Tong, Q; McGonnell, I; Demmers, T G M; Bergoug, H; Guinebretière, M; Eterradossi, N; Roulston, N; Verhelst, R; Bahr, C; Berckmans, D

2015-02-01

Thermodynamic study of incubated eggs is an important component in the optimisation of incubation processes. However, research on the interaction of heat and moisture transfer mechanisms in eggs is rather limited and does not focus on the hatching stage of incubation. During hatch, both the recently hatched chick and the broken eggshell add extra heat and moisture contents to the hatcher environment. In this study, we have proposed a novel way to estimate thermodynamically the amount of water evaporated from a broken eggshell during hatch. The hypothesis of this study considers that previously reported drops in eggshell temperature during hatching of chicks is the result remaining water content evaporating from the eggshell, released on the inner membrane by the recently hatched wet chick, just before hatch. To reproduce this process, water was sprayed on eggshells to mimic the water-fluid from the wet body of a chick. For each sample of eggshell, the shell geometry and weight, surface area and eggshell temperature were measured. Water evaporation losses and convection coefficient were calculated using a novel model approach considering the simultaneous heat and mass transfer profiles in an eggshell. The calculated average convective coefficient was 23.9 ± 7.5 W/m(2) °C, similar to previously reported coefficients in literature as a function of 0.5-1m/s air speed range. Comparison between measured and calculated values for the water evaporation showed 68% probability accuracy, associated to the use of an experimentally derived single heat transfer coefficient. The results support our proposed modelling approach of heat and mass transfer mechanisms. Furthermore, by estimating the amount of evaporated water in an eggshell post-hatch, air humidity levels inside the hatcher can be optimised to ensure wet chicks dry properly while not dehydrating early hatching chicks. Copyright © 2014 Elsevier Ltd. All rights reserved.

Factors Affecting Element Concentrations in Eggshells of Three Sympatrically Nesting Waterbirds in Northern Poland.

Science.gov (United States)

Kitowski, Ignacy; Jakubas, Dariusz; Indykiewicz, Piotr; Wiącek, Dariusz

2018-02-01

Avian eggshells are convenient samples in biomonitoring studies, because they are easily accessible, especially from colonially or semicolonially breeding birds. In the present study, concentrations of 17 elements, including heavy metals and essential elements in post-hatch eggshells, were compared among three species of waterbirds of differing strategies for gaining reserves for egg production and diet: mallard, Anas platyrhynchos (ML, a capital breeder, mainly herbivorous), common tern, Sterna hirundo (CT, an income breeder, piscivorous) and black-headed gull, Chroicocephalus ridibundus (BHG, mixed strategy, omnivorous) and breeding sympatrically in three sites in North Poland. Analyses revealed that Fe, Zn, and Cu levels differed the most in the studied species, which may be explained by various contributions of fish, aquatic plants, and soil invertebrates in their diets. Generally, the studied species' eggshells accumulated amounts of elements comparable to those reported for other waterbirds without putting the growth and development of the embryo at risk. The only exception was very high levels of Cr in ML and CT, which may be explained by their foraging on aquatic organisms in waterbodies polluted by this element. Intersite differences in eggshell concentrations of Ni, Sr, Hg and Cr in CT (an income breeder) may be explained by the influence of local pollution sources (small factories, polluted river).

Microbiome assembly of avian eggshells and their potential as transgenerational carriers of maternal microbiota.

Science.gov (United States)

van Veelen, H Pieter J; Salles, Joana Falcão; Tieleman, B Irene

2018-05-01

The microbiome is essential for development, health and homeostasis throughout an animal's life. Yet, the origins and transmission processes governing animal microbiomes remain elusive for non-human vertebrates, oviparous vertebrates in particular. Eggs may function as transgenerational carriers of the maternal microbiome, warranting characterisation of egg microbiome assembly. Here, we investigated maternal and environmental contributions to avian eggshell microbiota in wild passerine birds: woodlark Lullula arborea and skylark Alauda arvensis. Using 16S rRNA gene sequencing, we demonstrated in both lark species, at the population and within-nest levels, that bacterial communities of freshly laid eggs were distinct from the female cloacal microbiome. Instead, soil-borne bacteria appeared to thrive on freshly laid eggs, and eggshell microbiota composition strongly resembled maternal skin, body feather and nest material communities, sources in direct contact with laid eggs. Finally, phylogenetic structure analysis and microbial source tracking underscored species sorting from directly contacting sources rather than in vivo-transferred symbionts. The female-egg-nest system allowed an integrative assessment of avian egg microbiome assembly, revealing mixed modes of symbiont acquisition not previously documented for vertebrate eggs. Our findings illuminated egg microbiome origins, which suggested a limited potential of eggshells for transgenerational transmission, encouraging further investigation of eggshell microbiome functions in vertebrates.

Synthesis of three-dimensional calcium carbonate nanofibrous structure from eggshell using femtosecond laser ablation

Directory of Open Access Journals (Sweden)

Venkatakrishnan Krishnan

2011-01-01

Full Text Available Abstract Background Natural biomaterials from bone-like minerals derived from avian eggshells have been considered as promising bone substitutes owing to their biodegradability, abundance, and lower price in comparison with synthetic biomaterials. However, cell adhesion to bulk biomaterials is poor and surface modifications are required to improve biomaterial-cell interaction. Three-dimensional (3D nanostructures are preferred to act as growth support platforms for bone and stem cells. Although there have been several studies on generating nanoparticles from eggshells, no research has been reported on synthesizing 3D nanofibrous structures. Results In this study, we propose a novel technique to synthesize 3D calcium carbonate interwoven nanofibrous platforms from eggshells using high repetition femtosecond laser irradiation. The eggshell waste is value engineered to calcium carbonate nanofibrous layer in a single step under ambient conditions. Our striking results demonstrate that by controlling the laser pulse repetition, nanostructures with different nanofiber density can be achieved. This approach presents an important step towards synthesizing 3D interwoven nanofibrous platforms from natural biomaterials. Conclusion The synthesized 3D nanofibrous structures can promote biomaterial interfacial properties to improve cell-platform surface interaction and develop new functional biomaterials for a variety of biomedical applications.

Co-composting of eggshell waste in self-heating reactors: monitoring and end product quality

OpenAIRE

Soares, Micaela A. R.; Quina, Margarida M. J.; Quinta-Ferreira, Rosa M.

2013-01-01

Industrial eggshell waste (ES) is classified as an animal by-product not intended to human consumption. For reducing pathogen spreading risk due to soil incorporation of ES, sanitation by composting is a pre-treatment option. This work aims to evaluate eggshell waste recycling in self-heating composting reactors and investigate ES effect on process evolution and end product quality. Potato peel, grass clippings and rice husks were the starting organic materials considered. The incorporati...

Penguin eggshell membranes reflect homogeneity of mercury in the marine food web surrounding the Antarctic Peninsula

International Nuclear Information System (INIS)

Brasso, Rebecka L.; Polito, Michael J.; Lynch, Heather J.; Naveen, R.; Emslie, Steven D.

2012-01-01

Remote regions such as the Antarctic have become increasingly important for investigations into far-reaching anthropogenic impacts on the environment, most recently in regard to the global mercury cycle. Spatial patterns of mercury availability in four regions of the Antarctic Peninsula were investigated using three species of sympatrically breeding Pygoscelis penguins as biomonitors. Eggshells with intact membranes from Adélie, Gentoo, and Chinstrap penguins were collected at 24 breeding colonies in the South Orkney Islands, South Shetland Islands, eastern Antarctic Peninsula, and western Antarctic Peninsula during the 2006/2007 austral summer. In addition, we compared eggshell membrane mercury concentrations with eggshell stable isotope values (δ 15 N and δ 13 C) to determine if species-specific trophic or foraging habitat preferences influenced female mercury exposure prior to breeding. With few exceptions, mercury concentrations were found to be fairly homogeneous throughout the Antarctic Peninsula suggesting little spatial variation in the risk of exposure to dietary mercury in this food web. Mercury concentrations in Gentoo and Adélie penguins were similar while Chinstrap penguins tended to have higher eggshell membrane mercury concentrations than their congeners. However, inter and intra-specific differences in eggshell membrane mercury concentration were not related to eggshell δ 15 N or δ 13 C values, a likely result of all three species foraging at similar trophic positions. The lack of regional-scale differences in mercury availability in this marine ecosystem may be a reflection of generally uniform atmospheric deposition and upwelling of regionally homogeneous deep water rather than from geographically distinct point sources. -- Highlights: ► We examined regional patterns of mercury availability in the Antarctic Peninsula. ► Three species of Pygoscelis penguins were used as biomonitors. ► Chinstrap penguins tended to have higher mercury

THE EFFECT OF EGGSHELL MOSAIC TRAINING TOWARD FINE MOTOR SKILLS OF CHILDREN WITH INTELLECTUAL AND DEVELOPMENTAL DISABILITY (IDD

Directory of Open Access Journals (Sweden)

Diadra Finalistiani

2017-02-01

Full Text Available The purpose of this research was to determine the effect of eggshell mosaic toward fine motor skills of children with intellectual and develompental disability. The data was collected with observation, and the analysis technique used analysis in condition and analysis between conditions. The conclusion of this research was eggshell mosaic gives effect toward the fine motor skills of the children, it was shown from fine motor skills of the children before eggshell mosaic treatment, during the treatment and after controlling, and the fine motor skills of the children was improved.

Effects of Short-Term Carbohydrate Restrictive and Conventional Hypoenergetic Diets and Resistance Training on Strength Gains and Muscle Thickness

Directory of Open Access Journals (Sweden)

Claudia M. Meirelles, Paulo S.C. Gomes

2016-12-01

Full Text Available Hypoenergetic diets and resistance training (RT have been suggested to be important components of weight loss strategy programs; however, there is little evidence as to the chronic effects of different macronutrient compositions on strength performance and muscle mass with RT. The purpose of this study was to compare the effects of carbohydrate restrictive (CRD and conventional (CONV diets combined with RT on strength performance and muscle thicknesses in overweight and obese participants already involved in RT programs. Twenty-one volunteers engaged in an eight-week progressive RT program three times per week were assigned to a CRD (< 30 g carbohydrate; n = 12; 30.7 ± 3.9 km·m-2 or a CONV (30% energy deficit; 55%, 15% and 30% energy from carbohydrate, protein and fat, respectively; n=9; 27.7±2.5 km·m-2. Method: At baseline and week 8, the participants underwent body composition assessment by anthropometry, measurement of muscle thickness by ultrasound, and three strength tests using isotonic equipment. Both groups had similar reductions in body mass and fat mass as well as maintenance of fat-free mass. Muscle strength increased 14 ± 6% in the CRD group (p = 0.005 and 19 ± 9% in the CONV group (p = 0.028, with no significant differences between the groups. No significant differences were detected in muscle thicknesses within or between the groups. In conclusion, hypoenergetic diets combined with RT led to significant increases in muscle strength and were capable of maintaining muscle thicknesses in the upper and lower limbs of overweight and obese participants, regardless of the carbohydrate content of the diets.

Long-Term Strength of a Thick-Walled Pipe Filled with an Aggressive Medium, with Account for Damageability of the Pipe Material and Residual Strength

Science.gov (United States)

Piriev, S. A.

2018-01-01

This paper describes the study of scattered fracture of a thick-walled pipe filled with an aggressive medium, which creates uniform pressure on the inner surface of the pipe. It is assumed that the aggressive medium affects only the value of instantaneous strength. Damageability is described by an integral operator of the hereditary type. The problem is solved with allowance for residual strength of the pipe material behind the fracture front. Numerical calculation is carried out, and relationships between the fracture front coordinate and time for various concentrations of the aggressive medium and residual strength behind the fracture front are constructed.

FEM Modeling of In-Plane Stress Distribution in Thick Brittle Coatings/Films on Ductile Substrates Subjected to Tensile Stress to Determine Interfacial Strength

Directory of Open Access Journals (Sweden)

Kaishi Wang

2018-03-01

Full Text Available The ceramic-metal interface is present in various material structures and devices that are vulnerable to failures, like cracking, which are typically due to their incompatible properties, e.g., thermal expansion mismatch. In failure of these multilayer systems, interfacial shear strength is a good measure of the robustness of interfaces, especially for planar films. There is a widely-used shear lag model and method by Agrawal and Raj to analyse and measure the interfacial shear strength of thin brittle film on ductile substrates. The use of this classical model for a type of polymer derived ceramic coatings (thickness ~18 μm on steel substrate leads to high values of interfacial shear strength. Here, we present finite element simulations for such a coating system when it is subjected to in-plane tension. Results show that the in-plane stresses in the coating are non-uniform, i.e., varying across the thickness of the film. Therefore, they do not meet one of the basic assumptions of the classical model: uniform in-plane stress. Furthermore, effects of three significant parameters, film thickness, crack spacing, and Young’s modulus, on the in-plane stress distribution have also been investigated. ‘Thickness-averaged In-plane Stress’ (TIS, a new failure criterion, is proposed for estimating the interfacial shear strength, which leads to a more realistic estimation of the tensile strength and interfacial shear strength of thick brittle films/coatings on ductile substrates.

FEM Modeling of In-Plane Stress Distribution in Thick Brittle Coatings/Films on Ductile Substrates Subjected to Tensile Stress to Determine Interfacial Strength.

Science.gov (United States)

Wang, Kaishi; Zhang, Fangzhou; Bordia, Rajendra K

2018-03-27

The ceramic-metal interface is present in various material structures and devices that are vulnerable to failures, like cracking, which are typically due to their incompatible properties, e.g., thermal expansion mismatch. In failure of these multilayer systems, interfacial shear strength is a good measure of the robustness of interfaces, especially for planar films. There is a widely-used shear lag model and method by Agrawal and Raj to analyse and measure the interfacial shear strength of thin brittle film on ductile substrates. The use of this classical model for a type of polymer derived ceramic coatings (thickness ~18 μm) on steel substrate leads to high values of interfacial shear strength. Here, we present finite element simulations for such a coating system when it is subjected to in-plane tension. Results show that the in-plane stresses in the coating are non-uniform, i.e., varying across the thickness of the film. Therefore, they do not meet one of the basic assumptions of the classical model: uniform in-plane stress. Furthermore, effects of three significant parameters, film thickness, crack spacing, and Young's modulus, on the in-plane stress distribution have also been investigated. 'Thickness-averaged In-plane Stress' (TIS), a new failure criterion, is proposed for estimating the interfacial shear strength, which leads to a more realistic estimation of the tensile strength and interfacial shear strength of thick brittle films/coatings on ductile substrates.

Assessment of diagenetic alteration of dinosaur eggshells through petrography and geochemical analysis

Science.gov (United States)

Enriquez, M. V.; Eagle, R.; Eiler, J. M.; Tripati, A. K.; Ramirez, P. C.; Loyd, S. J.; Chiappe, L.; Montanari, S.; Norell, M.; Tuetken, T.

2012-12-01

Carbonate clumped isotope analysis of fossil eggshells has the potential to constrain both the physiology of extinct animals and, potentially, paleoenvironmental conditions, especially when coupled with isotopic measurements of co-occurring soil carbonates. Eggshell samples from both modern vertebrates and Cretaceous Hadrosaurid, Oviraptorid, Titanosaur, Hypselosaurus, Faveoolithus, dinosaur fossils have been collected from Auca Mahuevo, Argentina and Rousett, France, amongst other locations, for geochemical analysis to determine if isotopic signatures could be used to indicate warm- or cold-bloodedness. In some locations soil carbonates were also analyzed to constrain environmental temperatures. In order to test the validity of the geochemical results, an extensive study was undertaken to establish degree of diagenetic alteration. Petrographic and cathodoluminescence characterization of the eggshells were used to assess diagenetic alteration. An empirical 1-5 point scale was used to assign each sample an alteration level, and the observations were then compared with the geochemical results. Specimens displayed a wide range of alteration states. Some of which were well preserved and others highly altered. Another group seemed to be structural intact and only under cathodoluminescence was alteration clearly observed. In the majority of samples, alteration level was found to be predictably related to geochemical results. From specimens with little evidence for diagenesis, carbonate clumped isotope signatures support high (37-40°C) body temperature for Titanosaurid dinosaurs, but potentially lower body temperatures for other taxa. If these data do, in fact, represent original eggshell growth temperatures, these results support variability in body temperature amongst Cretaceous dinosaurs and potentially are consistent with variations between adult body temperature and size — a characteristic of 'gigantothermy'.

Adsorption of iron by using hybrid Akar Putra and commercialized chicken eggshells as bio-sorbents from aqueous solution

Directory of Open Access Journals (Sweden)

H.M. Nasir

2016-05-01

Full Text Available Heavy metal contamination in the environment could cause harmful effects both to human health and aquatic life. Numerous remediation methods had been developed to encounter with the contamination problem prior to degrade, decrease and to purify the contaminated water at minimal concentration as low as possible. Therefore, in current study, commercialized chicken eggshells and hybrid Akar Putra chicken eggshells were conducted in batch experiment to testify the capabilities of bio-sorbent materials in iron (II ion removal from aqueous solution at optimized level of dosage and equilibrium contact time. The optimum condition for iron (II removal for commercialized chicken eggshells and hybrid Akar Putra chicken eggshells bio-sorbents reached at 0.30 g with optimum contact time of 50 minutes and 91.83% and 91.07% of removal percentage with 0.60 g at 40 minutes. The final concentration from both bio-sorbents is achieved below than drinking water guideline (0.30 mg/L, 0.1635 mg/L and 0.1785 mg/L, respectively. The isotherm adsorption results showed it fitted better in Langmuir Isotherm Model than in Freundlich Isotherm Model, however with weak bonding, which could not held onto the heavy metal ions in long time period. In brief, commercialized chicken eggshells and hybrid Akar Putra chicken eggshells have considerable potential in removing heavy metal in aqueous solution. The selection of the bio-sorbent materials is more favorable as it reduces dependency towards chemical usage in water treatment which could have complied with drinking water guideline that can be obtained easily, abundance in amount, cheap and biodegradable.

Aggregation Strength Tuning in Difluorobenzoxadiazole-Based Polymeric Semiconductors for High-Performance Thick-Film Polymer Solar Cells.

Science.gov (United States)

Chen, Peng; Shi, Shengbin; Wang, Hang; Qiu, Fanglong; Wang, Yuxi; Tang, Yumin; Feng, Jian-Rui; Guo, Han; Cheng, Xing; Guo, Xugang

2018-06-27

High-performance polymer solar cells (PSCs) with thick active layers are essential for large-scale production. Polymer semiconductors exhibiting a temperature-dependent aggregation property offer great advantages toward this purpose. In this study, three difluorobenzoxadiazole (ffBX)-based donor polymers, PffBX-T, PffBX-TT, and PffBX-DTT, were synthesized, which contain thiophene (T), thieno[3,2- b]thiophene (TT), and dithieno[3,2- b:2',3'- d]thiophene (DTT) as the π-spacers, respectively. Temperature-dependent absorption spectra reveal that the aggregation strength increases in the order of PffBX-T, PffBX-TT, and PffBX-DTT as the π-spacer becomes larger. PffBX-TT with the intermediate aggregation strength enables well-controlled disorder-order transition in the casting process of blend film, thus leading to the best film morphology and the highest performance in PSCs. Thick-film PSCs with an average power conversion efficiency (PCE) of 8.91% and the maximum value of 9.10% are achieved using PffBX-TT:PC 71 BM active layer with a thickness of 250 nm. The neat film of PffBX-TT also shows a high hole mobility of 1.09 cm 2 V -1 s -1 in organic thin-film transistors. When PffBX-DTT and PffBX-T are incorporated into PSCs utilizing PC 71 BM acceptor, the average PCE decreases to 6.54 and 1.33%, respectively. The performance drop mainly comes from reduced short-circuit current, as a result of nonoptimal blend film morphology caused by a less well-controlled film formation process. A similar trend was also observed in nonfullerene type thick-film PSCs using IT-4F as the electron acceptor. These results show the significance of polymer aggregation strength tuning toward optimal bulk heterojunction film morphology using ffBX-based polymer model system. The study demonstrates that adjusting π-spacer is an effective method, in combination with other important approaches such as alkyl chain optimization, to generate high-performance thick-film PSCs which are critical for

Fabrication of a biocomposite reinforced with hydrophilic eggshell proteins

International Nuclear Information System (INIS)

Kim, GeunHyung; Min, Taijin; Park, Su A; Kim, Wan Doo; Koh, Young Ho

2007-01-01

Soluble eggshell proteins were used as a reinforcing material of electrospun micro/nanofibers for tissue engineering. A biocomposite composed of poly(ε-caprolactone) (PCL) micro/nanofibers and soluble eggshell protein was fabricated with a two-step fabrication method, which is an electrospinning process followed by an air-spraying process. To achieve a stable electrospinning process, we used an auxiliary cylindrical electrode connected with a spinning nozzle. PCL biocomposite was characterized in water contact angle and mechanical properties as well as cell proliferation for its application as a tissue engineering material. It showed an improved hydrophilic characteristic compared with that of a micro/nanofiber web generated from a pure PCL solution using a typical electrospinning process. Moreover, the fabricated biocomposite had good mechanical properties compared to a typical electrospun micro/nanofiber mat. The fabricated biocomposite made human dermal fibroblasts grow better than pure PCL. From the results, the reinforced polymeric micro/nanofiber scaffold can be easily achieved with these modified processes

Effect of spatial resolution of soil data on predictions of eggshell trace element levels in the Rook Corvus frugilegus.

Science.gov (United States)

Orłowski, Grzegorz; Siebielec, Grzegorz; Kasprzykowski, Zbigniew; Dobicki, Wojciech; Pokorny, Przemysław; Wuczyński, Andrzej; Polechoński, Ryszard; Mazgajski, Tomasz D

2016-12-01

Although a considerable research effort has gone into studying the dietary pathways of metals to the bodies of laying female birds and their eggs in recent years, no detailed investigations have yet been carried out relating the properties of the biogeochemical environment at large spatial scales to eggshell trace element levels in typical soil-invertebrate feeding birds under natural conditions. We used data from a large-scale nationwide monitoring survey of soil quality in Poland (3724 sampling points from the 43 792 available) to predict levels of five trace elements (copper [Cu], cadmium [Cd], nickel [Ni], zinc [Zn] and lead [Pb]) in Rook Corvus frugilegus eggshells from 42 breeding colonies. Our major aim was to test whether differences exist in the explanatory power of soil data (acidity, content of elements and organic matter, and particle size) used as a correlate of concentrations of eggshell trace elements among four different distances (5, 10, 15 and 20 km) around rookeries. Over all four distances around the rookeries only the concentrations of Cu and Cd in eggshells were positively correlated with those in soil, while eggshell Pb was correlated with the soil Pb level at the two longest distances (15 and 20 km) around the rookeries. The physical properties of soil (primarily the increase in pH) adversely affected eggshell Cd and Pb concentrations. The patterns and factors governing metal bioaccumulation in soil invertebrates and eggshells appear to be coincident, which strongly suggests a general similarity in the biochemical pathways of elements at different levels of the food web. The increasing acidification of arable soil as a result of excessive fertilisation and over-nitrification can enhance the bioavailability of toxic elements to laying females and their eggs. Copyright © 2016 Elsevier Ltd. All rights reserved.

Ratite eggshells from lanzarote, canary islands.

Science.gov (United States)

Franz Sauer, E G; Rothe, P

1972-04-07

Struthious and aepyornithoid eggshells from Tertiary calcareous sediments on Lanzarote prove the presence, until about 12 million years ago, of large flightless birds. The calcarenite horizon is recognized as an old land surface. Mesozoic sedimentary rocks in the basement of the volcanic islands of Lanzarote and neighboring Fuerteventura indicate that at least part of the Canary Archipelago is underlain by continental crust. Separation of the eastern Canaries from Africa raight have been by rifting, and a land connection might still have existed in the lower Pliocene.

Synthesis and chemical and structural characterization of hydroxyapatite obtained from eggshell and tricalcium phosphate

OpenAIRE

Arboleda, Alejandro; Franco, Manuel; Caicedo, Julio; Tirado, Liliana; Goyes, Clara

2016-01-01

The eggshell is a common residue that is usually discarded without giving any use to it. In this paper the results obtained from a proposed procedure to get hydroxyapatite (HA) from eggshell are shown. The HA is a calcium phosphate which has been widely used as implant material due to the close similarity of its composition with the inorganic phase of natural bone. HA generally has a high cost and it is presented as micro and nanostructured bioceramics; the last one is a promising option for ...

Penguin eggshell membranes reflect homogeneity of mercury in the marine food web surrounding the Antarctic Peninsula

Energy Technology Data Exchange (ETDEWEB)

Brasso, Rebecka L., E-mail: rlb1196@uncw.edu [University of North Carolina Wilmington, Department of Biology and Marine Biology, 601 South College Road, Wilmington, NC 28403 (United States); Polito, Michael J. [University of North Carolina Wilmington, Department of Biology and Marine Biology, 601 South College Road, Wilmington, NC 28403 (United States); Lynch, Heather J. [Ecology and Evolution Department, 640 Life Sciences Bldg., Stony Brook University, Stony Brook, NY 11794 (United States); Naveen, R. [Oceanites Inc., PO Box 15259, Chevy Chase, MD 20825 (United States); Emslie, Steven D. [University of North Carolina Wilmington, Department of Biology and Marine Biology, 601 South College Road, Wilmington, NC 28403 (United States)

2012-11-15

Remote regions such as the Antarctic have become increasingly important for investigations into far-reaching anthropogenic impacts on the environment, most recently in regard to the global mercury cycle. Spatial patterns of mercury availability in four regions of the Antarctic Peninsula were investigated using three species of sympatrically breeding Pygoscelis penguins as biomonitors. Eggshells with intact membranes from Adelie, Gentoo, and Chinstrap penguins were collected at 24 breeding colonies in the South Orkney Islands, South Shetland Islands, eastern Antarctic Peninsula, and western Antarctic Peninsula during the 2006/2007 austral summer. In addition, we compared eggshell membrane mercury concentrations with eggshell stable isotope values ({delta}{sup 15}N and {delta}{sup 13}C) to determine if species-specific trophic or foraging habitat preferences influenced female mercury exposure prior to breeding. With few exceptions, mercury concentrations were found to be fairly homogeneous throughout the Antarctic Peninsula suggesting little spatial variation in the risk of exposure to dietary mercury in this food web. Mercury concentrations in Gentoo and Adelie penguins were similar while Chinstrap penguins tended to have higher eggshell membrane mercury concentrations than their congeners. However, inter and intra-specific differences in eggshell membrane mercury concentration were not related to eggshell {delta}{sup 15}N or {delta}{sup 13}C values, a likely result of all three species foraging at similar trophic positions. The lack of regional-scale differences in mercury availability in this marine ecosystem may be a reflection of generally uniform atmospheric deposition and upwelling of regionally homogeneous deep water rather than from geographically distinct point sources. -- Highlights: Black-Right-Pointing-Pointer We examined regional patterns of mercury availability in the Antarctic Peninsula. Black-Right-Pointing-Pointer Three species of Pygoscelis

Synthesis of hydroxyapatite from waste egg-shell by Precipitation ...

African Journals Online (AJOL)

... of the samples. At optimal conditions, calculated stoichiometric ratio of Ca/P of the synthesized HAp powder (74 - 0565) of 1.65 closed to the theoretical value of Ca/P ratio (1.67) and amenable to biomedical applications, was obtained. Keywords: Hydroxyapatite; Egg-shell; Precipitation Method, Ca/P Stoichiometric Ratio.

Comparison of eggshell surface sanitization technologies and impacts on consumer acceptability.

Science.gov (United States)

Al-Ajeeli, Morouj N; Taylor, T Matthew; Alvarado, Christine Z; Coufal, Craig D

2016-05-01

Shell eggs can be contaminated with many types of microorganisms, including bacterial pathogens, and thus present a risk for the transmission of foodborne disease to consumers. Currently, most United States egg processors utilize egg washing and sanitization systems to decontaminate surfaces of shell eggs prior to packaging. However, previous research has indicated that current shell egg sanitization technologies employed in the commercial egg industry may not completely eliminate bacteria from the surface of eggshells, and thus alternative egg sanitization technologies with the potential for increased microbial reductions on eggshells should be investigated. The objectives of this study were to compare the antimicrobial efficacy and consumer sensory attributes of industry-available eggshell sanitization methods (chlorine and quaternary ammonium compounds (QAC) applied via spray) to various alternative egg sanitization technologies. Eggs (White Leghorn hens; n=195) were obtained for evaluation of sanitizer-induced reduction in mesophilic aerobic bacteria (n=90) or inoculated Salmonella Enteritidis (SE) reduction (n=105). Sanitizing treatments evaluated in this experiment were: chlorine spray (100 ppm available chlorine), QAC spray (200 ppm), peracetic acid spray (PAA; 135 ppm) alone or in combination with ultraviolet light (UV; 254 nm), and hydrogen peroxide (H2O2; 3.5% solution) spray in combination with UV (H2O2+UV). For enumeration of aerobic bacteria, eggs were sampled at 0, 7, and 14 days of storage at 4°C; surviving SE cells from inoculated eggs were enumerated by differential plating. Sensory trials were conducted to determine consumer liking of scrambled eggs made from eggs sanitized with chlorine, QAC, H2O2+UV, or no treatment (control). The H2O2 and UV treatment resulted in the greatest reductions in eggshell aerobic plate counts compared to other treatments throughout egg storage (Peggs represents a novel technology that could have important

Intraclutch eggshell colour variation in birds: are females able to identify their eggs individually?

Directory of Open Access Journals (Sweden)

Miroslav Poláček

2017-08-01

Full Text Available Background One possibility suggested regarding female post-mating strategies is differential allocation into offspring investment. Female birds produce not only the largest, but also most colourful eggs of all oviparous taxa. Larger eggs provide space for bigger embryos, or more nutrition for their development, but the question why eggs are more colourful and why there is variation in eggshell colouration remains. In this context, the focus of interest has been to explain inter-clutch variation but in many bird species, eggshell colouration also varies within a clutch. Surprisingly, less attention has been paid to this phenomenon. Therefore, we propose the “female egg recognition” hypothesis, suggesting that mothers use colour characteristics to interpret egg attributes and allocate further investment into each egg accordingly. To evaluate the feasibility of the hypothesis, we tested several underlying predictions and examined their suitability using a dataset from our tree sparrow (Passer montanus study. We predict (i substantial within-clutch variation in eggshell colouration which, (ii should be related to laying sequence, (iii reflect egg quality and, (iv should stimulate a female response. Methods Eggshell coloration data were obtained via digital photography under standardized conditions, taken after clutch completion. Lightness (L*, representing the achromatic properties of an egg has been chosen as the most important predictor in dark cavities and was related to egg quality and position in the nest. Results In our tree sparrows, first and mainly last eggs were less pigmented, providing information about laying order. Egg volume, which predicts chick quality, positively correlates with eggshell coloration. Finally, we could show that female tree sparrows placed darker, but not bigger, eggs into more central incubation positions. Discussion All basic prerequisites for the “female egg recognition” hypothesis are fulfilled. In this

Shakedown analysis of thick-walled cylinders subjected to internal pressure with the unified strength criterion

International Nuclear Information System (INIS)

Xu Shuanqiang; Yu Maohong

2005-01-01

Most previous studies on shakedown of thick-walled cylinders were based on the assumption that the compressive and tensile strengths of the materials were identical. In this paper the shakedown of an internally pressurized cylinder made of a material with a strength-difference and intermediate principal stress effects is dealt with by using a unified strength criterion which consists of a family of convex piecewise linear strength criteria. Through an elasto-plastic analysis the solutions for the loading stresses, residual stresses, elastic limit, plastic limit and shakedown limit of the cylinder are derived. It is shown that the present solutions include the classical plasticity solutions as special cases and have the ability to account for the strength-difference and intermediate principal stress effects. Finally, the influence of the two effects on the shakedown limit of the cylinder is investigated. The results show that the shakedown limit depends on the two effects and is underestimated if these effects are neglected as in the classical plasticity solution based on the Tresca criterion

Effect of heat stress on the gene expression of ion transporters/channels in the uterus of laying hens during eggshell formation.

Science.gov (United States)

Bahadoran, Shahab; Dehghani Samani, Amir; Hassanpour, Hossein

2018-01-01

Heat stress is a problem in laying hens as it decreases egg quality by decreasing eggshell mineralization. Heat stress alters gene expression, hence our aim was to investigate effects of heat stress on gene expression of ion transport elements involving in uterine mineralization (TRPV6, CALB1, ITPR3, SCNN1G, SLC4A4, KCNJ15, SLC4A9, and CLCN2) by real time quantitative PCR. Forty 23-week-old White Leghorn laying hens were housed in two rooms. The control group (n = 20) was maintained at 21-23 °C, and the heat stress group (n = 20) was exposed to 36-38 °C for 8 weeks. All parameters of egg quality including egg weight, surface area, volume, and eggshell weight, thickness, ash weight, and calcium content were decreased in the heat stress group compared to the control group (by 26.9%, 32.7%, 44.1%, 38.4%, 31.7%, 39.4%, and 11.1%, respectively). Total plasma calcium was decreased by 13.4%. Levels of ITPR3, SLC4A4, and SLC4A9 transcripts in the uterine lining were decreased in the heat stress group compared to the control group (by 61.4%, 66.1%, and 66.1%, respectively). CALB1 transcript level was increased (by 34.2 fold) in the heat stress group of hens compared to controls. TRPV6, SCNN1G, KCNJ15, and CLCN2 transcript levels did not significantly differ between control and heat stress groups of laying hens. It is concluded that the down-expression of ITPR3, SLC4A4, and SLC4A9 genes may impair transportation of Cl - , HCO 3 - , and Na + in eggshell mineralization during heat stress. Increased CALB1 gene expression may increase resistance of uterine cells to detrimental effects of heat stress.

Isotopic ordering in eggshells reflects body temperatures and suggests differing thermophysiology in two Cretaceous dinosaurs

Science.gov (United States)

Eagle, Robert A.; Enriquez, Marcus; Grellet-Tinner, Gerald; Pérez-Huerta, Alberto; Hu, David; Tütken, Thomas; Montanari, Shaena; Loyd, Sean J.; Ramirez, Pedro; Tripati, Aradhna K.; Kohn, Matthew J.; Cerling, Thure E.; Chiappe, Luis M.; Eiler, John M.

2015-10-01

Our understanding of the evolutionary transitions leading to the modern endothermic state of birds and mammals is incomplete, partly because tools available to study the thermophysiology of extinct vertebrates are limited. Here we show that clumped isotope analysis of eggshells can be used to determine body temperatures of females during periods of ovulation. Late Cretaceous titanosaurid eggshells yield temperatures similar to large modern endotherms. In contrast, oviraptorid eggshells yield temperatures lower than most modern endotherms but ~6 °C higher than co-occurring abiogenic carbonates, implying that this taxon did not have thermoregulation comparable to modern birds, but was able to elevate its body temperature above environmental temperatures. Therefore, we observe no strong evidence for end-member ectothermy or endothermy in the species examined. Body temperatures for these two species indicate that variable thermoregulation likely existed among the non-avian dinosaurs and that not all dinosaurs had body temperatures in the range of that seen in modern birds.

Isotopic ordering in eggshells reflects body temperatures and suggests differing thermophysiology in two Cretaceous dinosaurs.

Science.gov (United States)

Eagle, Robert A; Enriquez, Marcus; Grellet-Tinner, Gerald; Pérez-Huerta, Alberto; Hu, David; Tütken, Thomas; Montanari, Shaena; Loyd, Sean J; Ramirez, Pedro; Tripati, Aradhna K; Kohn, Matthew J; Cerling, Thure E; Chiappe, Luis M; Eiler, John M

2015-10-13

Our understanding of the evolutionary transitions leading to the modern endothermic state of birds and mammals is incomplete, partly because tools available to study the thermophysiology of extinct vertebrates are limited. Here we show that clumped isotope analysis of eggshells can be used to determine body temperatures of females during periods of ovulation. Late Cretaceous titanosaurid eggshells yield temperatures similar to large modern endotherms. In contrast, oviraptorid eggshells yield temperatures lower than most modern endotherms but ∼ 6 °C higher than co-occurring abiogenic carbonates, implying that this taxon did not have thermoregulation comparable to modern birds, but was able to elevate its body temperature above environmental temperatures. Therefore, we observe no strong evidence for end-member ectothermy or endothermy in the species examined. Body temperatures for these two species indicate that variable thermoregulation likely existed among the non-avian dinosaurs and that not all dinosaurs had body temperatures in the range of that seen in modern birds.

Synthesis of nano-textured biocompatible scaffolds from chicken eggshells

International Nuclear Information System (INIS)

Asghar, Waseem; Ilyas, Azhar; Sankaran, Jeyantt; Wan Yuan; Iqbal, Samir M; Kim, Young-Tae

2012-01-01

Cell adhesion, morphology and growth are influenced by surface topography at nano and micrometer scales. Nano-textured surfaces are prepared using photolithography, plasma etching and long polymer chemical etching which are cost prohibitive and require specialized equipment. This article demonstrates a simple approach to synthesize nano-textured scaffolds from chicken eggshells. Varieties of pattern are made on the eggshells like micro-needle forests and nanopores, giving very uniform nano-textures to the surfaces. The surfaces are characterized for chemical composition and crystal phase. The novel patterns are transferred to PDMS surfaces and the nano-textured PDMS surfaces are used to study the effect of texturing on human fibroblast cell growth and attachment. The effects of surface topographies, along with laminin coating on cell cultures, are also studied. We find an exciting phenomenon that the initial seeding density of the fibroblast cells affects the influence of the nano-texturing on cell growth. These nano-textured surfaces give 16 times more fibroblast growth when compared to flat PDMS surfaces. The novel nano-textured patterns also double the laminin adsorption on PDMS. (paper)

Using Eggshell in Acid Orange 2 Dye Removal from Aqueous Solution

Directory of Open Access Journals (Sweden)

Ahmad Reza Yari

2015-05-01

Full Text Available Background and purpose: Generated dye wastewater by the textile industry is usually toxic, non-biodegradable and resistant in the environment. Eggshell is one of the inexpensive material and for the reason the vesicular structures can be used as a proper adsorbent for pollutants removal. The aim of this study is to investigate the efficiency of eggshell for removal of acid orange 2 dye from aqueous solution. Materials and Methods: In the experimental study was determined the efficacy of variant variables such as contact time (15, 30, 60, 90 and 120 min, pH (3, 7 and 11, adsorbent dose (10, 25, 50 and 75 g/L, and initial dye concentration (25, 50 and 100 mg/L. The concentration of dye by spectrophotometer ultraviolet/visible in the wavelength 483 nm was examined. Results: The results showed that with increasing contact time and adsorbent dose, the dye removal efficiency was increased, but with increasing pH and initial dye concentration the removal efficiency was decreased. The maximum of removal efficiency of acid orange 2 dye got in the optimum pH: 3, contact time: 90 min, adsorbent dose: 50 g/L and initial dye concentration: 25 mg/L. Adsorption of acid orange 2 dye (R2 = 0.87 follow the Freundlich isotherm. Conclusion: Eggshells can be used as an inexpensive and effective adsorbent for the removal of acid orange 2 dye.

Oxygen inhibition layer of composite resins: effects of layer thickness and surface layer treatment on the interlayer bond strength.

Science.gov (United States)

Bijelic-Donova, Jasmina; Garoushi, Sufyan; Lassila, Lippo V J; Vallittu, Pekka K

2015-02-01

An oxygen inhibition layer develops on surfaces exposed to air during polymerization of particulate filling composite. This study assessed the thickness of the oxygen inhibition layer of short-fiber-reinforced composite in comparison with conventional particulate filling composites. The effect of an oxygen inhibition layer on the shear bond strength of incrementally placed particulate filling composite layers was also evaluated. Four different restorative composites were selected: everX Posterior (a short-fiber-reinforced composite), Z250, SupremeXT, and Silorane. All composites were evaluated regarding the thickness of the oxygen inhibition layer and for shear bond strength. An equal amount of each composite was polymerized in air between two glass plates and the thickness of the oxygen inhibition layer was measured using a stereomicroscope. Cylindrical-shaped specimens were prepared for measurement of shear bond strength by placing incrementally two layers of the same composite material. Before applying the second composite layer, the first increment's bonding site was treated as follows: grinding with 1,000-grit silicon-carbide (SiC) abrasive paper, or treatment with ethanol or with water-spray. The inhibition depth was lowest (11.6 μm) for water-sprayed Silorane and greatest (22.9 μm) for the water-sprayed short-fiber-reinforced composite. The shear bond strength ranged from 5.8 MPa (ground Silorane) to 36.4 MPa (water-sprayed SupremeXT). The presence of an oxygen inhibition layer enhanced the interlayer shear bond strength of all investigated materials, but its absence resulted in cohesive and mixed failures only with the short-fiber-reinforced composite. Thus, more durable adhesion with short-fiber-reinforced composite is expected. © 2014 Eur J Oral Sci.

Application of MMC model on simulation of shearing process of thick hot-rolled high strength steel plate

Energy Technology Data Exchange (ETDEWEB)

Dong, Liang; Li, Shuhui [Shanghai Key Laboratory of Digital Manufacture for Thin-walled Structures, Shanghai Jiao Tong University, Shanghai 200240 (China); Yang, Bing; Gao, Yongsheng [Automotive Steel Research Institute, R and D Center, BaoShan Iron and Steel Co.,Ltd, Shanghai 201900 (China)

2013-12-16

Shear operation is widely used as the first step in sheet metal forming to cut the sheet or plate into the required size. The shear of thick hot-rolled High Strength Steel (HSS) requires large shearing force and the sheared edge quality is relatively poor because of the large thickness and high strength compared with the traditional low carbon steel. Bad sheared edge quality will easily lead to edge cracking during the post-forming process. This study investigates the shearing process of thick hot-rolled HSS plate metal, which is generally exploited as the beam of heavy trucks. The Modified Mohr-Coulomb fracture criterion (MMC) is employed in numerical simulation to calculate the initiation and propagation of cracks during the process evolution. Tensile specimens are designed to obtain various stress states in tension. Equivalent fracture strains are measured with Digital Image Correlation (DIC) equipment to constitute the fracture locus. Simulation of the tension test is carried out to check the fracture model. Then the MMC model is applied to the simulation of the shearing process, and the simulation results show that the MMC model predicts the ductile fracture successfully.

Application of MMC model on simulation of shearing process of thick hot-rolled high strength steel plate

International Nuclear Information System (INIS)

Dong, Liang; Li, Shuhui; Yang, Bing; Gao, Yongsheng

2013-01-01

Shear operation is widely used as the first step in sheet metal forming to cut the sheet or plate into the required size. The shear of thick hot-rolled High Strength Steel (HSS) requires large shearing force and the sheared edge quality is relatively poor because of the large thickness and high strength compared with the traditional low carbon steel. Bad sheared edge quality will easily lead to edge cracking during the post-forming process. This study investigates the shearing process of thick hot-rolled HSS plate metal, which is generally exploited as the beam of heavy trucks. The Modified Mohr-Coulomb fracture criterion (MMC) is employed in numerical simulation to calculate the initiation and propagation of cracks during the process evolution. Tensile specimens are designed to obtain various stress states in tension. Equivalent fracture strains are measured with Digital Image Correlation (DIC) equipment to constitute the fracture locus. Simulation of the tension test is carried out to check the fracture model. Then the MMC model is applied to the simulation of the shearing process, and the simulation results show that the MMC model predicts the ductile fracture successfully

Fronto-orbital feminization technique. A surgical strategy using fronto-orbital burring with or without eggshell technique to optimize the risk/benefit ratio.

Science.gov (United States)

Villepelet, A; Jafari, A; Baujat, B

2018-05-04

The demand for facial feminization is increasing in transsexual patients. Masculine foreheads present extensive supraorbital bossing with a more acute glabellar angle, whereas female foreheads show softer features. The aim of this article is to describe our surgical technique for fronto-orbital feminization. The mask-lift technique is an upper face-lift. It provides rejuvenation by correcting collapsed features, and fronto-orbital feminization through burring of orbital rims and lateral canthopexies. Depending on the size of the frontal sinus and the thickness of its anterior wall, frontal remodeling is achieved using simple burring or by means of the eggshell technique. Orbital remodeling comprises a superolateral orbital opening, a reduction of ridges and a trough at the lateral orbital rim to support the lateral canthopexy. Frontal, corrugator and procerus myectomies, plus minimal scalp excision, complete the surgery. Our technique results in significant, natural-looking feminization. No complications were observed in our series of patients. The eggshell technique is an alternative to bone flap on over-pneumatized sinus. Fronto-orbital feminization fits into a wider surgical strategy. It can be associated to rhinoplasty, genioplasty, mandibular angle remodeling, face lift and laryngoplasty. Achieving facial feminization in 2 or 3 stages improves psychological and physiological tolerance. Copyright © 2018 Elsevier Masson SAS. All rights reserved.

The evolution of size of the uropygial gland: mutualistic feather mites and uropygial secretion reduce bacterial loads of eggshells and hatching failures of European birds.

Science.gov (United States)

Soler, J J; Peralta-Sánchez, J M; Martín-Platero, A M; Martín-Vivaldi, M; Martínez-Bueno, M; Møller, A P

2012-09-01

Potentially, pathogenic bacteria are one of the main infective agents against which a battery of chemical and physical barriers has evolved in animals. Among these are the secretions by the exocrine uropygial gland in birds. The antimicrobial properties of uropygial secretions may prevent colonization and growth of microorganisms on feathers, skin and eggshells. However, uropygial gland secretions also favour the proliferation of feather mites that feed on secretions and microorganisms living on feathers that would otherwise reach eggshells during incubation if not consumed by feather mites. Therefore, at the interspecific level, uropygial gland size (as an index of volume of uropygial secretion) should be positively related to eggshell bacterial load (i.e. the risk of egg infection), whereas eggshell bacterial loads may be negatively related to abundance of feather mites eating bacteria. Here, we explore these previously untested predictions in a comparative framework using information on eggshell bacterial loads, uropygial gland size, diversity and abundance of feather mites and hatching success of 22 species of birds. The size of the uropygial gland was positively related to eggshell bacterial loads (mesophilic bacteria and Enterobacteriaceae), and bird species with higher diversity and abundance of feather mites harboured lower bacterial density on their eggshells (Enterococcus and Staphylococcus), in accordance with the hypothesis. Importantly, eggshell bacterial loads of mesophilic bacteria, Enterococcus and Enterobacteriaceae were negatively associated with hatching success, allowing us to interpret these interspecific relationships in a functional scenario, where both uropygial glands and mutualistic feather mites independently reduce the negative effects of pathogenic bacteria on avian fitness. © 2012 The Authors. Journal of Evolutionary Biology © 2012 European Society For Evolutionary Biology.

Characteristics of Skeletal Musculature of Pheasants Hatched from Eggs of Different Eggshell Colour

Directory of Open Access Journals (Sweden)

Dragan Zikic

2016-05-01

Full Text Available The aim of this paper was to examine morphodinamics of development of skeletal musculature of pheasants hatched from eggs of different eggshell colour. Four groups of pheasant eggs (dark brown, light brown, brown/green and blue/green were incubated. Samples of skeletal musculature of leg and breast were taken during the embryonic and neonatal period of development. From taken samples histological preparations were made. In pheasants hatched from blue/green eggs the smaller diameter of leg and breast muscle cells and the higher volume density of connective tissue in leg and breast muscles were recorded. It was concluded that pheasants hatched from blue/green eggs had the weakest development of skeletal musculature, which can be related to structural differences of eggshell of various colour.

Fossil struthionid eggshells from Laetoli, Tanzania: Taxonomic and biostratigraphic significance

Science.gov (United States)

Harrison, Terry; Msuya, Charles P.

2005-04-01

Recent paleontological investigations at Laetoli and neighboring localities in northern Tanzania have produced a large collection of fossil ostrich eggshells from the Pliocene-aged Laetolil Beds (˜3.5-4.5 Ma) and Ndolanya Beds (˜2.6-2.7 Ma). A detailed analysis of the morphology of the eggshells and their taxonomic affinities indicates that two different species of Struthio are represented. In the Lower Laetolil Beds and in the Upper Laetolil Beds below Tuff 3 a new species is recognized— Struthio kakesiensis. This is replaced in the Upper Laetolil Beds by Struthio camelus, the modern species of ostrich. Since radiometric age determinations are available for the stratigraphic sequence at Laetoli, it is possible to precisely date the first appearance of S. camelus at ˜3.6-3.8 Ma. Comparisons of the Laetoli material with specimens from the well-dated sequences at Lothagam and Kanapoi in northern Kenya, allow the taxonomic and biochronological analysis to be extended back in time to the late Miocene. At about 6.5 Ma, Diamantornis and elephant birds were replaced in East Africa by ostriches belonging to the genus Struthio. Three time-successive species of ostriches are identified in the fossil record of East Africa, beginning with Struthio. cf. karingarabensis (˜6.5-4.2 Ma), followed by S. kakesiensis (˜4.5-3.6 Ma) and then S. camelus (˜3.8 Ma onwards). A similar sequence of taxa has previously been recorded from localities in Namibia, but at these sites there is no possibility to precisely calibrate the ages of the different species using radiometric dating. Nevertheless, the broadly similar evolutionary sequence and the close correspondence in inferred ages for the succession of species in East Africa and Namibia suggest that ostrich eggshells are a very useful tool for biochronological correlation of paleontological sites in sub-Saharan Africa.

The Effect of Lithium Disilicate Ceramic Thickness and Translucency on Shear Bond Strength of Light-cured Resin Cement

Directory of Open Access Journals (Sweden)

Mohammad Javad Moghaddas

2017-09-01

Full Text Available Introduction: To achieve acceptable clinical performance, a ceramic veneer must be bonded to enamel by well-polymerized resin cement. Among different factors, thickness and translucency of the ceramic may affect the resin cement polymerization. Thus, the current study evaluated the effect of the thickness and translucency of lithium disilicate ceramic on light-cured resin cement bond strength to enamel. Methods: In this laboratory study, 208 sound bovine incisors were equally divided into 16 groups (n = 13. The lithium disilicate ceramic cubes in four thicknesses (0.4, 0.6, 0.8 and 1 mm with four translucencies (high and medium opaque, high and low translucent were fabricated and bonded to prepared enamel surfaces using a light-cured translucent resin cement according to manufacturer recommendations. After 5000 cycles of thermocycling, the bonded specimens were placed in a universal testing machine and loaded to the point of fracture. To determine the mode of failure, each sample was observed under a stereomicroscope. Data were recorded and analyzed by Shapiro-Wilk test and two-way analysis of variance (ANOVA. Results: The ceramic thickness and translucency could not significantly affect shear bond strength (SBS of resin cement to enamel (p = 0.17 and p = 0.097, respectively.  The Adhesive and ceramic cohesive failures were reported as the maximum and minimum mode of failure, respectively. Conclusion: The SBS of the light-cured resin cement bonding to enamel and lithium disilicate ceramic was not affected by the translucency of ceramics having a thickness of less than 1 mm.

CORRELATES OF EGGSHELL THICKNESS

African Journals Online (AJOL)

DJFLEX

quality and quantity of eggs. These measures include good sanitation and environmental conditions, adequate feeding of hens in terms of quantity and quality and vaccination of birds. Other factors which the farmers take into consideration include age of bird at lay, location and genotype of the hen. The question here is.

Residues of chromium, nickel, cadmium and lead in Rook Corvus frugilegus eggshells from urban and rural areas of Poland.

Science.gov (United States)

Orłowski, Grzegorz; Kasprzykowski, Zbigniew; Dobicki, Wojciech; Pokorny, Przemysław; Wuczyński, Andrzej; Polechoński, Ryszard; Mazgajski, Tomasz D

2014-08-15

We examined the concentrations of chromium (Cr), nickel (Ni), cadmium (Cd) and lead (Pb) in Rook Corvus frugilegus eggshells from 43 rookeries situated in rural and urban areas of western (=intensive agriculture) and eastern (=extensive agriculture) Poland. We found small ranges in the overall level of Cr (the difference between the extreme values was 1.8-fold; range of concentrations=5.21-9.40 Cr ppm), Ni (3.5-fold; 1.15-4.07 Ni ppm), and Cd (2.6-fold; 0.34-0.91 Cd ppm), whereas concentrations of Pb varied markedly, i.e. 6.7-fold between extreme values (1.71-11.53 Pb ppm). Eggshell levels of these four elements did not differ between rural rookeries from western and eastern Poland, but eggshells from rookeries in large/industrial cities had significantly higher concentrations of Cr, Ni and Pb than those from small towns and villages. Our study suggests that female Rooks exhibited an apparent variation in the intensity of trace metal bioaccumulation in their eggshells, that rapid site-dependent bioaccumulation of Cu, Cr, Ni and Pb occurs as a result of the pollution gradient (ruralsoil environment. Copyright © 2014 Elsevier B.V. All rights reserved.

Bio-active synthesis of tin oxide nanoparticles using eggshell membrane for energy storage application

Science.gov (United States)

Celina Selvakumari, J.; Nishanthi, S. T.; Dhanalakshmi, J.; Ahila, M.; Pathinettam Padiyan, D.

2018-05-01

Nano-sized tin oxide (SnO2) particles were synthesized using eggshell membrane (ESM), a natural bio-waste from the chicken eggshell. The crystallization of SnO2 into the tetragonal structure was confirmed from powder X-ray diffraction and the crystallite size ranged from 13 to 40 nm. Various shapes including rod, hexagonal and spherical SnO2 nanoparticles were observed from the morphological studies. The electrochemical impedance study revealed a lower charge transfer resistance (Rct) of 8.565 Ω and the presence of a constant phase element which arised due to surface roughness and porosity. Capacitive behavior seen in the cyclic voltammetry curve of the prepared SnO2 nanoparticles, find future applications in supercapacitors.

Eggshell Powder as an Adsorbent for Removal of Fluoride from Aqueous Solution: Equilibrium, Kinetic and Thermodynamic Studies

Directory of Open Access Journals (Sweden)

R. Bhaumik

2012-01-01

Full Text Available A new medium, eggshell powder has been developed for fluoride removal from aqueous solution. Fluoride adsorption was studied in a batch system where adsorption was found to be pH dependent with maximum removal efficiency at 6.0. The experimental data was more satisfactorily fitted with Langmuir isotherm model. The kinetics and the factor controlling adsorption process fully accepted by pseudo-second-order model were also discussed. Ea was found to be 45.98 kJmol-1 by using Arrhenius equation, indicating chemisorption nature of fluoride onto eggshell powder. Thermodynamic study showed spontaneous nature and feasibility of the adsorption process with negative enthalpy (∆H0 value also supported the exothermic nature. Batch experiments were performed to study the applicability of the adsorbent by using fluoride contaminated water collected from affected areas. These results indicate that eggshell powder can be used as an effective, low-cost adsorbent to remove fluoride from aqueous solution as well as groundwater.

Nesting behaviour influences species-specific gas exchange across avian eggshells.

Science.gov (United States)

Portugal, Steven J; Maurer, Golo; Thomas, Gavin H; Hauber, Mark E; Grim, Tomáš; Cassey, Phillip

2014-09-15

Carefully controlled gas exchange across the eggshell is essential for the development of the avian embryo. Water vapour conductance (G(H2O)) across the shell, typically measured as mass loss during incubation, has been demonstrated to optimally ensure the healthy development of the embryo while avoiding desiccation. Accordingly, eggs exposed to sub-optimal gas exchange have reduced hatching success. We tested the association between eggshell G(H2O) and putative life-history correlates of adult birds, ecological nest parameters and physical characteristics of the egg itself to investigate how variation in G(H2O) has evolved to maintain optimal water loss across a diverse set of nest environments. We measured gas exchange through eggshell fragments in 151 British breeding bird species and fitted phylogenetically controlled, general linear models to test the relationship between G(H2O) and potential predictor parameters of each species. Of our 17 life-history traits, only two were retained in the final model: wet-incubating parent and nest type. Eggs of species where the parent habitually returned to the nest with wet plumage had significantly higher G(H2O) than those of parents that returned to the nest with dry plumage. Eggs of species nesting in ground burrows, cliffs and arboreal cups had significantly higher G(H2O) than those of species nesting on the ground in open nests or cups, in tree cavities and in shallow arboreal nests. Phylogenetic signal (measured as Pagel's λ) was intermediate in magnitude, suggesting that differences observed in the G(H2O) are dependent upon a combination of shared ancestry and species-specific life history and ecological traits. Although these data are correlational by nature, they are consistent with the hypothesis that parents constrained to return to the nest with wet plumage will increase the humidity of the nest environment, and the eggs of these species have evolved a higher G(H2O) to overcome this constraint and still

Early life stress shapes female reproductive strategy through eggshell pigmentation in Japanese quail

Czech Academy of Sciences Publication Activity Database

Duval, C.; Zimmer, C.; Mikšík, Ivan; Cassey, P.; Spencer, K.A.

2014-01-01

Roč. 208, Nov 1 (2014), s. 146-153 ISSN 0016-6480 Institutional support: RVO:67985823 Keywords : breeding conditions * early-life stress * eggshell pigmentation * Japanese quail Subject RIV: ED - Physiology Impact factor: 2.470, year: 2014

Data set for the proteomic inventory and quantitative analysis of chicken eggshell matrix proteins during the primary events of eggshell mineralization and the active growth phase of calcification

Directory of Open Access Journals (Sweden)

Pauline Marie

2015-09-01

Full Text Available Chicken eggshell is a biomineral composed of 95% calcite calcium carbonate mineral and of 3.5% organic matrix proteins. The assembly of mineral and its structural organization is controlled by its organic matrix. In a recent study [1], we have used quantitative proteomic, bioinformatic and functional analyses to explore the distribution of 216 eggshell matrix proteins at four key stages of shell mineralization defined as: (1 widespread deposition of amorphous calcium carbonate (ACC, (2 ACC transformation into crystalline calcite aggregates, (3 formation of larger calcite crystal units and (4 rapid growth of calcite as columnar structure with preferential crystal orientation. The current article detailed the quantitative analysis performed at the four stages of shell mineralization to determine the proteins which are the most abundant. Additionally, we reported the enriched GO terms and described the presence of 35 antimicrobial proteins equally distributed at all stages to keep the egg free of bacteria and of 81 proteins, the function of which could not be ascribed.

Data set for the proteomic inventory and quantitative analysis of chicken eggshell matrix proteins during the primary events of eggshell mineralization and the active growth phase of calcification.

Science.gov (United States)

Marie, Pauline; Labas, Valérie; Brionne, Aurélien; Harichaux, Grégoire; Hennequet-Antier, Christelle; Rodriguez-Navarro, Alejandro B; Nys, Yves; Gautron, Joël

2015-09-01

Chicken eggshell is a biomineral composed of 95% calcite calcium carbonate mineral and of 3.5% organic matrix proteins. The assembly of mineral and its structural organization is controlled by its organic matrix. In a recent study [1], we have used quantitative proteomic, bioinformatic and functional analyses to explore the distribution of 216 eggshell matrix proteins at four key stages of shell mineralization defined as: (1) widespread deposition of amorphous calcium carbonate (ACC), (2) ACC transformation into crystalline calcite aggregates, (3) formation of larger calcite crystal units and (4) rapid growth of calcite as columnar structure with preferential crystal orientation. The current article detailed the quantitative analysis performed at the four stages of shell mineralization to determine the proteins which are the most abundant. Additionally, we reported the enriched GO terms and described the presence of 35 antimicrobial proteins equally distributed at all stages to keep the egg free of bacteria and of 81 proteins, the function of which could not be ascribed.

Effect of H3PO4 Concentration and Particle Size of the Eggshell Used in Laying Hens Fed on Bone and Blood

Directory of Open Access Journals (Sweden)

S. Kismiati

2013-06-01

Full Text Available Normal 0 false false false IN X-NONE X-NONE MicrosoftInternetExplorer4 The objective of this research was to evaluate the effect of H3 PO4 concentrations and particle size of eggshell used in the feed of laying hens on bone and blood profiles. Ninety-six laying hens (Isa Brown strain age 25 weeks were kept in individual battery cage and divided into 8 groups randomly. Group 1 was fed using eggshell with out H3PO4 and particle size of <1 mm (feed 1 , group 2 was fed using eggshell that has been soaked in H3PO4 3% and particle size of <1 mm (feed 2, group 3 were fed using eggshell that has been soaked in H3PO4 4% and particle size of <1 mm (feed 3, group 4 was fed using eggshell that has been soaked in H3PO4 5% and particle size of <1 mm (feed 4, group 5 was fed using eggshell that has been soaked in H3PO4 and particle size of <3 mm (feed 5 , group of 6 was fed using eggshell that has been soaked in H3PO4 3% and particle size of <3 mm (feed 6, group 7 was fed using eggshell that has been soaked in H3PO4 4 % and particle size of <3 mm (feed 7 and a group of 8 was fed using eggshell that has been soaked in H3PO4 5% and particle size of <3 mm (feed 8. A Completely Randomized Design patterns factorial 4 x 2 x 3 was used in this research. Result of this research showed that had no interaction effect (P>0.05 between the H3PO4 concentration and particle size of eggshell on weight, volume, diameter of tibia bone and calcium and phosphorus content of the blood. The concentration of H3PO4 or particles size also had no effect (P>0.05 on all variables. Normal 0 false false false IN X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font

Periodical low eggshell temperatures during incubation and post hatch dietary arginine supplementation

NARCIS (Netherlands)

Afsarian, O.; Shahir, M.H.; Akhlaghi, A.; Lotfolahian, H.; Hoseini, A.; Lourens, A.

2016-01-01

An experiment was conducted to evaluate the effects of a periodically low eggshell temperature exposure during incubation and dietary supplementation of arginine on performance, ascites incidence, and cold tolerance acquisition in broilers. A total of 2,400 hatching eggs were randomly assigned to

Mercury concentrations in eggshells of the Southern Ground-Hornbill (Bucorvus leadbeateri) and Wattled Crane (Bugeranus carunculatus) in South Africa.

Science.gov (United States)

Daso, Adegbenro P; Okonkwo, Jonathan O; Jansen, Raymond; Brandao, José D D O; Kotzé, Antoinette

2015-04-01

In this study, wild hatched eggshells were collected from the nests of threatened Wattled Crane and South Ground-Hornbill in an attempt to determine their total Hg concentrations. A total of fourteen eggshell samples from both bird species were collected from different study areas in the Mpumlanga and KwaZulu-Natal Provinces of South Africa. The eggshells were acid digested under reflux and their total Hg concentrations were determined using cold-vapour atomic absorption spectrophotometry (CV-AAS). The observed total Hg levels for the South Ground-Hornbill samples ranged from 1.31 to 8.88 µg g(-1) dry weight (dw), except for one outlier which had an elevated 75.0 µg g(-1) dw. The levels obtained for the Wattled Crane samples were relatively high and these ranged from 14.84 to 36.37 µg g(-1) dw. Generally, all the measured total Hg concentrations for the Wattled Crane samples exceeded the estimated total Hg levels derived for eggshell which were known to cause adverse reproductive effects in avian species from previous studies. Based on these findings, it is, therefore, possible that the exposure of these birds to elevated Hg may have contributed to their present population decline. Copyright © 2015 Elsevier Inc. All rights reserved.

500-Gray γ-Irradiation May Increase Adhesion Strength of Lyophilized Cadaveric Split-Thickness Skin Graft to Wound Bed.

Science.gov (United States)

Wei, Lin-Gwei; Chen, Chieh-Feng; Wang, Chi-Hsien; Cheng, Ya-Chen; Li, Chun-Chang; Chiu, Wen-Kuan; Wang, Hsian-Jenn

2017-03-01

Human cadaveric skin grafts are considered as the "gold standard" for temporary wound coverage because they provide a more conductive environment for natural wound healing. Lyophilization, packing, and terminal sterilization with gamma-ray can facilitate the application of cadaveric split-thickness skin grafts, but may alter the adhesion properties of the grafts. In a pilot study, we found that 500 Gy γ-irradiation seemed not to reduce the adherence between the grafts and wound beds. We conducted this experiment to compare the adherences of lyophilized, 500-Gy γ-irradiated skin grafts to that of lyophilized, nonirradiated grafts. Pairs of wounds were created over the backs of Sprague- Dawley rats. Pairs of "lyophilized, 500-Gy γ-irradiated" and "lyophilized, nonirradiated" cadaveric split-thickness skin grafts were fixed to the wound beds. Adhesion strength between the grafts and the wound beds was measured and compared. On post-skin-graft day 7 and day 10, the adhesion strength of γ-irradiated grafts was greater than that of the nonirradiated grafts. Because lyophilized cadaveric skin grafts can be vascularized and the collagen of its dermal component can be remodeled after grafting, the superior adhesion strength of 500-Gy γ-irradiated grafts can be explained by the collagen changes from irradiation.

Synthesis and characterization of eggshell-derived hydroxyapatite via mechanochemical method: A comparative study

Science.gov (United States)

Hamidi, A. A.; Salimi, M. N.; Yusoff, A. H. M.

2017-04-01

The focus of bone graft properties has developed through generations, from the ability to withstand mechanical stress to the ability to integrate with the biological structure. In recent years, the use of hydroxyapatite (HA) as bone graft material in orthopedic and dental applications has been increasing. HA is a natural occuring mineral with excellent bioactivity but relatively poor mechanical properties. It constitutes 96% portion of enamel in teeth and 67% portion of bone. HA can be extracted from animal bones or fabricated from synthetic or biologic sources. In this study, eggshells were used as raw material to synthesize eggshell-derived HA (EHA) via mechanochemical method. The synthesis of EHA involved CaO, which was obtained from the calcination of eggshells, and reaction with dicalcium hydrogen phosphate dihydrous (DCPD) or phosphoric acid (H3PO4). The effects of rotational speed and heat treatment temperature on EHA's characteristics were investigated. The characterization studies were carried out by using the Fourier Transform Infrared Spectroscopy (FTIR), X-Ray Diffraction (XRD) analysis and Scanning Electron Microscopy (SEM). HA powder was successfully synthesized with crystallite and particle sizes in the range of 8-47 nm and 250-550 nm respectively. It was observed from this study that the increase of milling rotational speed had increased the phase purity of EHA samples. Furthermore, the higher heating temperature of HA samples resulted in higher degree of crystallinity of HA and the appearance of β-tricalcium phosphate (β-TCP) as secondary phase.

Residual stress in a thick section high strength T-butt weld

International Nuclear Information System (INIS)

Pearce, S.V.; Linton, V.M.; Oliver, E.C.

2008-01-01

Residual stresses in a structure are generated as a result of the various fabrication and welding processes used to make the component. Being able to quantify these residual stresses is a key step in determining the continuing integrity of a structure in service. In this work, the residual stresses around a high strength, quenched and tempered steel T-butt web to curved plate weld have been measured using neutron strain scanning. The results show that the residual stresses near the weld were dominated by the welding residual stresses, while the stresses further from the weld were dominated by the bending residual stresses. The results suggest that the combination of welding-induced residual stress and significant pre-welding residual stress, as in the case of a thick bent section of plate can significantly alter the residual stress profile from that in a flat plate

Calcined Eggshell Waste for Mitigating Soil Antibiotic-Resistant Bacteria/Antibiotic Resistance Gene Dissemination and Accumulation in Bell Pepper.

Science.gov (United States)

Ye, Mao; Sun, Mingming; Feng, Yanfang; Li, Xu; Schwab, Arthur P; Wan, Jinzhong; Liu, Manqiang; Tian, Da; Liu, Kuan; Wu, Jun; Jiang, Xin

2016-07-13

The combined accumulation of antibiotics, heavy metals, antibiotic-resistant bacteria (ARB)/antibiotic resistance genes (ARGs) in vegetables has become a new threat to human health. This is the first study to investigate the feasibility of calcined eggshells modified by aluminum sulfate as novel agricultural wastes to impede mixed contaminants from transferring to bell pepper (Capsicum annuum L.). In this work, calcined eggshell amendment mitigated mixed pollutant accumulation in bell pepper significantly, enhanced the dissipation of soil tetracycline, sulfadiazine, roxithromycin, and chloramphenicol, decreased the water-soluble fractions of antibiotics, and declined the diversity of ARB/ARGs inside the vegetable. Moreover, quantitative polymerase chain reaction analysis detected that ARG levels in the bell pepper fruits significantly decreased to 10(-10) copies/16S copies, indicating limited risk of ARGs transferring along the food chain. Furthermore, the restoration of soil microbial biological function suggests that calcined eggshell is an environmentally friendly amendment to control the dissemination of soil ARB/ARGs in the soil-vegetable system.

Depositional setting and early diagenesis of the dinosaur eggshell-bearing Aren Fm at Bastus, Late Campanian, south-central Pyrenees

Science.gov (United States)

Díaz-Molina, Margarita; Kälin, Otto; Benito, M. Isabel; Lopez-Martinez, Nieves; Vicens, Enric

2007-07-01

The Late Cretaceous Aren Fm exposed north of Bastus in the Tremp Basin (south-central Pyrenees) preserves an excellent record of dinosaur eggs laid in a marine littoral setting. Different from other cases reported in literature, at the Bastus site the preferential nesting ground was original beach sand. The coastal deposits of Aren Fm can be grouped into four facies assemblages, representing respectively shoreface, beachface, beach ridge plain and backbarrier lagoon environments. Shoreface deposits include fine- to coarse-grained hybrid arenites and subordinate quartz-dominated conglomerates with ripple structures of wave and wave-current origin. Beachface deposits are mainly storm beach conglomerates, but parallel-laminated foreshore arenites locally occur. Backbarrier lagoon deposits comprise of washover sandy conglomerates that grade laterally into sandy lime mudstones, biomicrites and marls. Beach ridge sediment, wherein the bulk of dinosaur eggs and eggshell debris occurs, predominantly is a reddish hybrid arenite that has undergone a complex early diagenetic evolution, including marine and meteoric cementation followed by soil development. The reddish arenites overlie wave-dominated shoreface deposits and in places pass laterally into lagoonal deposits. They originally formed shore ridges, that became stabilized during progradational episodes by pedogenesis (beach ridge, sensu [Otvos, E.G., 2000. Beach ridges—definitions and significance. Geomorphology 32, 83-108.]), which also affected the dinosaur eggs. The eggshell-bearing beach ridge arenites are typically preserved at the top of parasequences forming the systems tracts of a third-order sequence. Thick packages of this facies resulted from aggradation of barrier/beach ridge deposits, whose preservation below surfaces of transgressive erosion was favoured by incipient lithification.

Salmonella penetration through eggshells of chickens of different genetic backgrounds.

Science.gov (United States)

Rathgeber, Bruce M; McCarron, Paige; Budgell, Krista L

2013-09-01

Eggs have been identified as a source of salmonellosis, making the transmission of Salmonella to eggs of great concern to the poultry industry. The goal of this experiment was to determine the ability of Salmonella to penetrate the eggshell of 5 different breeds of noncommercial chicken, Barred Plymouth Rock, White Leghorn, Brown Leghorn, Fayoumi, and Light Sussex, and 1 commercial Lohmann LSL-Lite. Egg weight, breaking force, shell weight, and shell thickness measurements were taken for 30 eggs per breed. A 1 cm in diameter hole was cut out from the narrow end of 30 additional eggs per breed. The shells were filled with plate count agar containing tetracycline and 0.1% 2,3,5-triphenyl terazolium chloride and sealed with paraffin wax. Agar-filled eggs were submerged for 1 min in an overnight culture of tetracycline-resistant Salmonella Heidelberg and incubated at 37°C for 40 h. Eggs were candled and visual colonies were counted and reported as cfu per egg and cfu per gram of shell. The SAS mixed model was used to evaluate differences between breeds for egg quality characteristics and the number of cfu per egg and per gram of shell. Commercial layers (62.6 g) and Barred Plymouth Rock (61.5 g) produced the largest eggs, whereas Fayoumi (47.1 g) produced the smallest (P heritage chicken breeds as a genetic resource for the future.

Utilization of eggshell waste as low-cost solid base catalyst for biodiesel production from used cooking oil

Science.gov (United States)

Asri, N. P.; Podjojono, B.; Fujiani, R.; Nuraini

2017-05-01

A solid CaO-based catalyst of waste eggshell was developed for biodiesel production from used cooking oil. The waste eggshell powder was calcined in air at 90° C for 4 h to convert calcium species in the eggshells into active CaO catalysts. The characterization of CaO catalyst was done by XRD and BET analysis. The CaO catalyst was then introduced for transesterification of used cooking oil (UCO) for testing of its catalytic activity. The experiment was conducted in batch type reactor that consists of three-neck glass equipped by reflux condenser and magnetic stirrer. Before tranesterification process, the UCO was treated by coconut coir powder in order to reduce the free fatty acid content. The result showed that the catalyst was potentially use for transesterification of used cooking oil into biodiesel with relatively high yield of 75.92% was achieved at reaction temperature, reaction time, molar ratio UCO to methanol and catalyst amount of 65° C, 7 h, 1:15 and 6%, respectively.

Innate humoural immunity is related to eggshell bacterial load of European birds: a comparative analysis

Science.gov (United States)

Soler, Juan José; Peralta-Sánchez, Juan Manuel; Flensted-Jensen, Einar; Martín-Platero, Antonio Manuel; Møller, Anders Pape

2011-09-01

Fitness benefits associated with the development of a costly immune system would include not only self-protection against pathogenic microorganisms but also protection of host offspring if it reduces the probability and the rate of vertical transmission of microorganisms. This possibility predicts a negative relationship between probabilities of vertical transmission of symbionts and level of immune response that we here explore inter-specifically. We estimated eggshell bacterial loads by culturing heterotrophic bacteria, Enterococcus, Staphylococcus and Enterobacteriaceae on the eggshells of 29 species of birds as a proxy of vertical transmission of bacteria from mother to offspring. For this pool of species, we also estimated innate immune response (natural antibody and complement (lysis)) of adults, which constitute the main defence against bacterial infection. Multivariate general linear models revealed the predicted negative association between natural antibodies and density of bacteria on the eggshell of 19 species of birds for which we sampled the eggs in more than one nest. Univariate analyses revealed significant associations for heterotrophic bacteria and for Enterobacteriaceae, a group of bacteria that includes important pathogens of avian embryos. Therefore, these results suggest a possible trans-generational benefit of developing a strong immune system by reducing vertical transmission of pathogens.

Residues of chromium, nickel, cadmium and lead in Rook Corvus frugilegus eggshells from urban and rural areas of Poland

International Nuclear Information System (INIS)

Orłowski, Grzegorz; Kasprzykowski, Zbigniew; Dobicki, Wojciech; Pokorny, Przemysław; Wuczyński, Andrzej; Polechoński, Ryszard; Mazgajski, Tomasz D.

2014-01-01

We examined the concentrations of chromium (Cr), nickel (Ni), cadmium (Cd) and lead (Pb) in Rook Corvus frugilegus eggshells from 43 rookeries situated in rural and urban areas of western (= intensive agriculture) and eastern (= extensive agriculture) Poland. We found small ranges in the overall level of Cr (the difference between the extreme values was 1.8-fold; range of concentrations = 5.21–9.40 Cr ppm), Ni (3.5-fold; 1.15–4.07 Ni ppm), and Cd (2.6-fold; 0.34–0.91 Cd ppm), whereas concentrations of Pb varied markedly, i.e. 6.7-fold between extreme values (1.71–11.53 Pb ppm). Eggshell levels of these four elements did not differ between rural rookeries from western and eastern Poland, but eggshells from rookeries in large/industrial cities had significantly higher concentrations of Cr, Ni and Pb than those from small towns and villages. Our study suggests that female Rooks exhibited an apparent variation in the intensity of trace metal bioaccumulation in their eggshells, that rapid site-dependent bioaccumulation of Cu, Cr, Ni and Pb occurs as a result of the pollution gradient (rural < urban), and that Cd levels are probably regulated physiologically, even though these were relatively high, which could be treated as an overall proxy of a heavy Cd load in the soil environment. - Highlights: • Concentrations of Cr, Ni, Cd and Pb are reported for Rook eggshells from 43 rookeries. • Cr, Ni and Pb levels were significantly higher in urban than in rural areas. • Bioaccumulation of Cr, Ni and Pb suggests a pollution gradient (urban > rural areas). • Females rapidly bioaccumulate Cr, Ni and Pb in breeding areas. • No difference found for Cd levels, which are probably regulated physiologically

Residues of chromium, nickel, cadmium and lead in Rook Corvus frugilegus eggshells from urban and rural areas of Poland

Energy Technology Data Exchange (ETDEWEB)

Orłowski, Grzegorz, E-mail: orlog@poczta.onet.pl [Institute of Agricultural and Forest Environment, Polish Academy of Sciences, Bukowska 19, 60-809 Poznań (Poland); Kasprzykowski, Zbigniew [Department of Ecology and Nature Protection, Siedlce University of Natural Sciences and Humanities, Prusa 12, 08-110 Siedlce (Poland); Dobicki, Wojciech; Pokorny, Przemysław [Department of Limnology and Fishery, Wrocław University of Environmental and Life Sciences, Chełmońskiego 38C, 51-630 Wrocław (Poland); Wuczyński, Andrzej [Institute of Nature Conservation, Polish Academy of Sciences, Lower-Silesian Field Station, Podwale 75, 50-449 Wrocław (Poland); Polechoński, Ryszard [Department of Limnology and Fishery, Wrocław University of Environmental and Life Sciences, Chełmońskiego 38C, 51-630 Wrocław (Poland); Mazgajski, Tomasz D. [Museum and Institute of Zoology, Polish Academy of Sciences, Wilcza 64, 00-679 Warszawa (Poland)

2014-08-15

We examined the concentrations of chromium (Cr), nickel (Ni), cadmium (Cd) and lead (Pb) in Rook Corvus frugilegus eggshells from 43 rookeries situated in rural and urban areas of western (= intensive agriculture) and eastern (= extensive agriculture) Poland. We found small ranges in the overall level of Cr (the difference between the extreme values was 1.8-fold; range of concentrations = 5.21–9.40 Cr ppm), Ni (3.5-fold; 1.15–4.07 Ni ppm), and Cd (2.6-fold; 0.34–0.91 Cd ppm), whereas concentrations of Pb varied markedly, i.e. 6.7-fold between extreme values (1.71–11.53 Pb ppm). Eggshell levels of these four elements did not differ between rural rookeries from western and eastern Poland, but eggshells from rookeries in large/industrial cities had significantly higher concentrations of Cr, Ni and Pb than those from small towns and villages. Our study suggests that female Rooks exhibited an apparent variation in the intensity of trace metal bioaccumulation in their eggshells, that rapid site-dependent bioaccumulation of Cu, Cr, Ni and Pb occurs as a result of the pollution gradient (rural < urban), and that Cd levels are probably regulated physiologically, even though these were relatively high, which could be treated as an overall proxy of a heavy Cd load in the soil environment. - Highlights: • Concentrations of Cr, Ni, Cd and Pb are reported for Rook eggshells from 43 rookeries. • Cr, Ni and Pb levels were significantly higher in urban than in rural areas. • Bioaccumulation of Cr, Ni and Pb suggests a pollution gradient (urban > rural areas). • Females rapidly bioaccumulate Cr, Ni and Pb in breeding areas. • No difference found for Cd levels, which are probably regulated physiologically.

Investigation of structure, adhesion strength, wear performance and corrosion behavior of platinum/ruthenium/nitrogen doped diamond-like carbon thin films with respect to film thickness

Energy Technology Data Exchange (ETDEWEB)

Khun, N.W. [School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore 639798 (Singapore); Liu, E., E-mail: MEJLiu@ntu.edu.sg [School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore 639798 (Singapore)

2011-03-15

Research highlights: {yields} Sputtered PtRuN-DLC thin films were fabricated with different film thicknesses. {yields} The graphitization of the films increased with increased film thickness. {yields} The wear resistance of the films increased though their adhesion strength decreased. {yields} The corrosion potentials of the films shifted to more negative values. {yields} However, the corrosion currents of the films decreased. - Abstract: In this study, the corrosion performance of platinum/ruthenium/nitrogen doped diamond-like carbon (PtRuN-DLC) thin films deposited on p-Si substrates using a DC magnetron sputtering deposition system in a 0.1 M NaCl solution was investigated using potentiodynamic polarization test in terms of film thickness. The effect of the film thickness on the chemical composition, bonding structure, surface morphology, adhesion strength and wear resistance of the PtRuN-DLC films was studied using X-ray photoelectron spectroscopy (XPS), micro-Raman spectroscopy, atomic force microscopy (AFM), micro-scratch test and ball-on-disc tribotest, respectively. It was found that the wear resistance of the PtRuN-DLC films apparently increased with increased film thickness though the adhesion strength of the films decreased. The corrosion results revealed that the increased concentration of sp{sup 2} bonds in the PtRuN-DLC films with increased film thickness shifted the corrosion potentials of the films to more negative values but the decreased porosity density in the films significantly decreased the corrosion currents of the films.

Investigation of structure, adhesion strength, wear performance and corrosion behavior of platinum/ruthenium/nitrogen doped diamond-like carbon thin films with respect to film thickness

International Nuclear Information System (INIS)

Khun, N.W.; Liu, E.

2011-01-01

Research highlights: → Sputtered PtRuN-DLC thin films were fabricated with different film thicknesses. → The graphitization of the films increased with increased film thickness. → The wear resistance of the films increased though their adhesion strength decreased. → The corrosion potentials of the films shifted to more negative values. → However, the corrosion currents of the films decreased. - Abstract: In this study, the corrosion performance of platinum/ruthenium/nitrogen doped diamond-like carbon (PtRuN-DLC) thin films deposited on p-Si substrates using a DC magnetron sputtering deposition system in a 0.1 M NaCl solution was investigated using potentiodynamic polarization test in terms of film thickness. The effect of the film thickness on the chemical composition, bonding structure, surface morphology, adhesion strength and wear resistance of the PtRuN-DLC films was studied using X-ray photoelectron spectroscopy (XPS), micro-Raman spectroscopy, atomic force microscopy (AFM), micro-scratch test and ball-on-disc tribotest, respectively. It was found that the wear resistance of the PtRuN-DLC films apparently increased with increased film thickness though the adhesion strength of the films decreased. The corrosion results revealed that the increased concentration of sp 2 bonds in the PtRuN-DLC films with increased film thickness shifted the corrosion potentials of the films to more negative values but the decreased porosity density in the films significantly decreased the corrosion currents of the films.

Eggshell pigmentation has no evident effects on offspring viability in common kestrels

Czech Academy of Sciences Publication Activity Database

Fargallo, J. A.; López-Rull, I.; Mikšík, Ivan; Eckhardt, Adam; Peralta-Sánchez, J. M.

2014-01-01

Roč. 28, č. 4 (2014), s. 627-637 ISSN 0269-7653 R&D Projects: GA ČR(CZ) GA13-17224S Institutional support: RVO:67985823 Keywords : biliverdin IX * egg colouration * eggshell proteins * falco tinnunculus * protoporphyrin IX Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 2.517, year: 2014

Efficacy of phosphatidic acid ingestion on lean body mass, muscle thickness and strength gains in resistance-trained men

Directory of Open Access Journals (Sweden)

Hoffman Jay R

2012-10-01

Full Text Available Abstract Background Phosphatidic acid (PA has been reported to activate the mammalian target of rapamycin (mTOR signaling pathway and is thought to enhance the anabolic effects of resistance training. The purpose of this pilot study was to examine if oral phosphatidic acid administration can enhance strength, muscle thickness and lean tissue accruement during an 8-week resistance training program. Methods Sixteen resistance-trained men were randomly assigned to a group that either consumed 750 mg of PA (n = 7, 23.1 ± 4.4 y; 176.7 ± 6.7 cm; 86.5 ± 21.2 kg or a placebo (PL, n = 9, 22.5 ± 2.0 y; 179.8 ± 5.4 cm; 89.4 ± 13.6 kg group. During each testing session subjects were assessed for strength (one repetition maximum [1-RM] bench press and squat and body composition. Muscle thickness and pennation angle were also measured in the vastus lateralis of the subject’s dominant leg. Results Subjects ingesting PA demonstrated a 12.7% increase in squat strength and a 2.6% increase in LBM, while subjects consuming PL showed a 9.3% improvement in squat strength and a 0.1% change in LBM. Although parametric analysis was unable to demonstrate significant differences, magnitude based inferences indicated that the Δ change in 1-RM squat showed a likely benefit from PA on increasing lower body strength and a very likely benefit for increasing lean body mass (LBM. Conclusions Results of this study suggest that a combination of a daily 750 mg PA ingestion, combined with a 4-day per week resistance training program for 8-weeks appears to have a likely benefit on strength improvement, and a very likely benefit on lean tissue accruement in young, resistance trained individuals.

UV, VISIBLE AND NIR SPECTRAL ANALYSIS OF EGGSHELLS IN THE CHARADRIIDAE FAMILY OF BIRDS

Science.gov (United States)

We employed reflectance spectrophotometry to quantify color and mineral composition of eggshells from several species of the bird family Charadriidae to characterize species physiology and to distinguish nesting habitat preferences. We used a Shimadzu spectrophotometer to measur...

Sorption of Pb(II and Cu(II by low-cost magnetic eggshells-Fe3O4 powder

Directory of Open Access Journals (Sweden)

Ren Jianwei

2012-01-01

Full Text Available This study explored the feasibility of using magnetic eggshell-Fe3O4 powder as adsorbent for the removal of Pb(II and Cu(II ions from aqueous solution. The metal ionsadsorption media interaction was characterized using XRD and FTIR. The effects of contact time, initial concentrations, temperature, solution pH and reusability of the adsorption media were investigated. The metal ions adsorption was fast and the amount of metal ions adsorbed increased with an increase in temperature, suggesting an endothermic adsorption. The kinetic data showed that the adsorption process followed the pseudo-second-order kinetic model. The optimal adsorption pH value was around 5.5 at which condition the equilibrium capacity was 263.2 mg/g for Pb(II and 250.0 for Cu(II. The adsorption equilibrium data fitted very well to the Langmuir and Freundlich adsorption isotherm models. The thermodynamics of Pb(II and Cu(II adsorption onto the magnetic eggshell-Fe3O4 powder indicated that the adsorption was spontaneous. The reusability study has proven that magnetic eggshell-Fe3O4 powder can be employed as a low-cost and easy to separate adsorbent.

Feasibility of sulfate-calcined eggshells for removing pathogenic bacteria and antibiotic resistance genes from landfill leachates.

Science.gov (United States)

Ye, Mao; Sun, Mingming; Chen, Xu; Feng, Yanfang; Wan, Jinzhong; Liu, Kuan; Tian, Da; Liu, Manqiang; Wu, Jun; Schwab, Arthur P; Jiang, Xin

2017-05-01

High abundance of human pathogen and antibiotic resistance genes (ARGs) in landfill leachate has become an emerging threat against human health. Therefore, sulfate- and calcination-modified eggshells as green agricultural bioresource were applied to test the feasibility of removing pathogenic bacteria and ARGs from leachate. The highest removal of Escherichia coli (E. coil) and gentamycin resistant gene (gmrA) from artificial contaminated landfill leachate was achieved by the application of eggshell with combined treatment of sulfate and calcination. The 16S and gmrA gene copies of E. coil declined significantly from 1.78E8±8.7E6 and 4.12E8±5.9E6 copies mL -1 to 1.32E7±2.6E6 and 2.69E7±7.2E6 copies mL -1 , respectively, within 24h dynamic adsorption equilibrium process (ppathogenic bacteria and ARGs (tet, sul, erm, qnr, and ampC) indicated its great efficiency to purify landfill leachates. This study demonstrated that sulfate-calcined eggshells can be an environmentally-friendly and highly efficient bioadsorbent to the management of reducing dissemination risk of pathogen and ARGs in landfill leachate. Copyright © 2017 Elsevier Ltd. All rights reserved.

Intra-clutch and inter-colony variability in element concentrations in eggshells of the black-headed gull, Chroicocephalus ridibundus, in northern Poland.

Science.gov (United States)

Kitowski, Ignacy; Indykiewicz, Piotr; Wiącek, Dariusz; Jakubas, Dariusz

2017-04-01

Eggshells are good bioindicators of environmental contamination, and therefore, the concentrations of 17 trace elements in 87 eggshells of black-headed gulls, Chroicocephalus ridibundus, were determined in five breeding colonies in an area dominated by farmland in northern Poland. The intra-clutch variability in the eggshell concentrations of heavy metals and other elements was also investigated, and the concentrations of the elements showed the following pattern: Ca > Mg > Sr > Fe > Zn > Al > Cr > Se > Mn > Cu > Pb > As > Ni > Mo = V > Sc > Cd. The concentrations of Fe, Al, and Mn decreased with the order in which the eggs were laid, but Sr concentrations increased. In contrast, the concentration of Cu significantly increased with the laying date. The concentrations of all elements significantly differed among the studied colonies; the highest concentration of eight elements was found in the eggshells from the Kusowo colony, which may have resulted from the intensive use of fertilizers, manure, and slurry in the surrounding agricultural region. The concentrations of Mg, Sr, and Zn in the eggshells from Skoki Duże were higher than those of the other studied colonies, which may have occurred because the gulls were nesting in a functioning gravel pit; soil and the parent rock are natural reservoirs of these elements. The observed element levels indicate that the environment where the black-headed gull eggs were formed, i.e., primarily near the breeding colonies, remains in a relatively unpolluted state, which was reflected by the low levels of Cd, Ni, and Pb and the lack of measurable levels of Hg.

Fatigue behavior of thick composite single lap joints

Energy Technology Data Exchange (ETDEWEB)

Tang, J.H.; Sridhar, I.; Srikanth, N. [Nanyang Technological Univ., Singapore (Singapore)

2012-07-01

In consideration of bondline thickness variability, in bonded joints where thick adherend is adopted, relative thick adhesive layer (2-5 mm) is preferable. This paper aims to give some insight in fatigue strength of adhesively bonded structures involving thick adherend coupled with thick adhesive layer. Single lap joints with nominal adherend thickness of 8 mm and two different nominal thicknesses (2.5 mm and 5.5 mm) were made and tested under fatigue loading. The failure mode exhibits always a tendency for interfacial initiation, followed by interlaminar separation. Fatigue strength for higher adhesive thickness is found to be lower. (Author)

Eggshell membrane: A natural substrate for immobilization and detection of DNA

Energy Technology Data Exchange (ETDEWEB)

Ray, Preetam Guha; Roy, Somenath, E-mail: sroy@cgcri.res.in

2016-02-01

Chemically modified eggshell membranes (ESM) have been explored as potentially novel platforms for immobilization of oligonucleotides and subsequent detection of target DNA. The fibrous network of the native ESM as well those functionalized with acetic acid or n-butyl acetate has been examined by field-emission scanning electron microscopy (FESEM). The formation of surface functional moieties has been confirmed by Fourier-transform infrared spectroscopy (FTIR). DNA molecules, with an end terminal − NH{sub 2} group (at 5′ end) have been immobilized on the chemically modified ESM surface. The effect of surface modification on the DNA immobilization efficiency has been investigated using fluorescence microscopy and atomic force microscopy (AFM). The above studies concurrently suggest that functionalization of ESM with n-butyl acetate causes a better homogeneity of the DNA probes on the membrane surface. On-chip hybridization of the target DNA with the surface bound capture probes has been performed on the functionalized membranes. It is observed that n-butyl acetate modification of ESM pushes the limit of detection (LOD) of the DNA sensors by at least an order of magnitude compared to the other modification method. - Graphical abstract: Eggshell membranes (ESM) have been chemically modified with acetic acid or n-butyl acetate for immobilization of aminated capture probes and subsequent detection of fluorophore-tagged target DNA molecules. n-Butyl acetate modified ESM exhibits superior homogeneity of capture probe immobilization and lower limit of detection for the target DNA molecules. - Highlights: • Eggshell membranes (ESM) have been explored as potentially novel platforms for immobilization of oligonucleotides. • Compared to native ESM, those modified with acetic acid or n-butyl acetate have shown more efficient loading of DNA probes. • ESM modified with n-butyl acetate pushed the lower limit of detection (LOD) of the sensor down to 10 nM of target DNA

Condition-dependent strategies of eggshell pigmentation: an experimental study of Japanese quail (Coturnix coturnix japonica)

Czech Academy of Sciences Publication Activity Database

Duval, C.; Cassey, P.; Mikšík, Ivan; Reynolds, S.J.; Spencer, K.A.

2013-01-01

Roč. 216, č. 4 (2013), s. 700-708 ISSN 0022-0949 Institutional support: RVO:67985823 Keywords : body condition * eggshell colouration * food restriction * pigment allocation Subject RIV: EG - Zoology Impact factor: 3.002, year: 2013

Eggshell Porosity Provides Insight on Evolution of Nesting in Dinosaurs.

Directory of Open Access Journals (Sweden)

Kohei Tanaka

Full Text Available Knowledge about the types of nests built by dinosaurs can provide insight into the evolution of nesting and reproductive behaviors among archosaurs. However, the low preservation potential of their nesting materials and nesting structures means that most information can only be gleaned indirectly through comparison with extant archosaurs. Two general nest types are recognized among living archosaurs: 1 covered nests, in which eggs are incubated while fully covered by nesting material (as in crocodylians and megapodes, and 2 open nests, in which eggs are exposed in the nest and brooded (as in most birds. Previously, dinosaur nest types had been inferred by estimating the water vapor conductance (i.e., diffusive capacity of their eggs, based on the premise that high conductance corresponds to covered nests and low conductance to open nests. However, a lack of statistical rigor and inconsistencies in this method render its application problematic and its validity questionable. As an alternative we propose a statistically rigorous approach to infer nest type based on large datasets of eggshell porosity and egg mass compiled for over 120 extant archosaur species and 29 archosaur extinct taxa/ootaxa. The presence of a strong correlation between eggshell porosity and nest type among extant archosaurs indicates that eggshell porosity can be used as a proxy for nest type, and thus discriminant analyses can help predict nest type in extinct taxa. Our results suggest that: 1 covered nests are likely the primitive condition for dinosaurs (and probably archosaurs, and 2 open nests first evolved among non-avian theropods more derived than Lourinhanosaurus and were likely widespread in non-avian maniraptorans, well before the appearance of birds. Although taphonomic evidence suggests that basal open nesters (i.e., oviraptorosaurs and troodontids were potentially the first dinosaurs to brood their clutches, they still partially buried their eggs in sediment

Eggshell Porosity Provides Insight on Evolution of Nesting in Dinosaurs.

Science.gov (United States)

Tanaka, Kohei; Zelenitsky, Darla K; Therrien, François

2015-01-01

Knowledge about the types of nests built by dinosaurs can provide insight into the evolution of nesting and reproductive behaviors among archosaurs. However, the low preservation potential of their nesting materials and nesting structures means that most information can only be gleaned indirectly through comparison with extant archosaurs. Two general nest types are recognized among living archosaurs: 1) covered nests, in which eggs are incubated while fully covered by nesting material (as in crocodylians and megapodes), and 2) open nests, in which eggs are exposed in the nest and brooded (as in most birds). Previously, dinosaur nest types had been inferred by estimating the water vapor conductance (i.e., diffusive capacity) of their eggs, based on the premise that high conductance corresponds to covered nests and low conductance to open nests. However, a lack of statistical rigor and inconsistencies in this method render its application problematic and its validity questionable. As an alternative we propose a statistically rigorous approach to infer nest type based on large datasets of eggshell porosity and egg mass compiled for over 120 extant archosaur species and 29 archosaur extinct taxa/ootaxa. The presence of a strong correlation between eggshell porosity and nest type among extant archosaurs indicates that eggshell porosity can be used as a proxy for nest type, and thus discriminant analyses can help predict nest type in extinct taxa. Our results suggest that: 1) covered nests are likely the primitive condition for dinosaurs (and probably archosaurs), and 2) open nests first evolved among non-avian theropods more derived than Lourinhanosaurus and were likely widespread in non-avian maniraptorans, well before the appearance of birds. Although taphonomic evidence suggests that basal open nesters (i.e., oviraptorosaurs and troodontids) were potentially the first dinosaurs to brood their clutches, they still partially buried their eggs in sediment. Open nests

Immobilization of Pb, Cd, and Zn in a contaminated soil using eggshell and banana stem amendments: metal leachability and a sequential extraction study.

Science.gov (United States)

Ashrafi, Mehrnaz; Mohamad, Sharifah; Yusoff, Ismail; Shahul Hamid, Fauziah

2015-01-01

Heavy-metal-contaminated soil is one of the major environmental pollution issues all over the world. In this study, two low-cost amendments, inorganic eggshell and organic banana stem, were applied to slightly alkaline soil for the purpose of in situ immobilization of Pb, Cd, and Zn. The artificially metal-contaminated soil was treated with 5% eggshell or 10% banana stem. To simulate the rainfall conditions, a metal leaching experiment for a period of 12 weeks was designed, and the total concentrations of the metals in the leachates were determined every 2 weeks. The results from the metal leaching analysis revealed that eggshell amendment generally reduced the concentrations of Pb, Cd, and Zn in the leachates, whereas banana stem amendment was effective only on the reduction of Cd concentration in the leachates. A sequential extraction analysis was carried out at the end of the experiment to find out the speciation of the heavy metals in the amended soils. Eggshell amendment notably decreased mobility of Pb, Cd, and Zn in the soil by transforming their readily available forms to less accessible fractions. Banana stem amendment also reduced exchangeable form of Cd and increased its residual form in the soil.

Synthesis and characterization of Fe–Ni/ɣ-Al2O3 egg-shell catalyst for H2 generation by ammonia decomposition

DEFF Research Database (Denmark)

Silva, Hugo José Lopes; Nielsen, Morten Godtfred; Fiordaliso, Elisabetta Maria

2015-01-01

The Fe–Ni alloyed nanoparticles are a promising alternative to expensive ruthenium-based catalysts for a real-scale application of hydrogen generation by ammonia decomposition. In practical applications, millimeter-sized extrudates are used as catalyst supports, where the spatial distribution...... of the active phase should match with the type of reaction. In this work, a novel synthesis route was developed for the preparation of a Fe–Ni/ɣ-Al2O3 egg-shell catalyst. Egg-shell is a preferred profile considering the highly endothermic nature of ammonia decomposition reaction. The high viscosity of glycerol...... using focused ion bean (FIB) milling allowed to acquire high resolution images of the Ni and Fe nanoparticles on ɣ-Al2O3, which is particularly challenging due to the crystalline nature of this support. Distinct regions of the egg-shell catalyst were analyzed through scanning TEM (STEM) and TEM...

Acute Ultraviolet Radiation Perturbs Epithelialization but not the Biomechanical Strength of Full-thickness Cutaneous Wounds

DEFF Research Database (Denmark)

Danielsen, Patricia L; Lerche, Catharina M; Wulf, Hans Christian

2016-01-01

SED, 3 SED and 5 SED. Twenty-four hours after UV irradiation, inflammation was quantified by skin reflectance (erythema) and myeloperoxidase (MPO) tissue levels, and two 6 mm full-thickness excisional wounds and one 3 cm incisional wound were inflicted. Epidermal hyperplasia was assessed...... (P epithelial coverage decreased (P = 0.024) by increasing the UVR dose, whereas there was no significant difference (P = 0.765) in wound MPO levels. Neither wound width (P = 0.850) nor breaking strength (P...... = 0.320) differed among the groups. Solar-simulated UVR 24 h before wounding impaired epithelialization but was not detrimental for surgical incisional wound healing....

Does contrast between eggshell ground and spot coloration affect egg rejection?

Science.gov (United States)

Dainson, Miri; Hauber, Mark E; López, Analía V; Grim, Tomáš; Hanley, Daniel

2017-08-01

Obligate avian brood parasitic species impose the costs of incubating foreign eggs and raising young upon their unrelated hosts. The most common host defence is the rejection of parasitic eggs from the nest. Both egg colours and spot patterns influence egg rejection decisions in many host species, yet no studies have explicitly examined the role of variation in spot coloration. We studied the American robin Turdus migratorius, a blue-green unspotted egg-laying host of the brown-headed cowbird Molothrus ater, a brood parasite that lays non-mimetic spotted eggs. We examined host responses to model eggs with variable spot coloration against a constant robin-mimetic ground colour to identify patterns of rejection associated with perceived contrast between spot and ground colours. By using avian visual modelling, we found that robins were more likely to reject eggs whose spots had greater chromatic (hue) but not achromatic (brightness) contrast. Therefore, egg rejection decision rules in the American robin may depend on the colour contrast between parasite eggshell spot and host ground coloration. Our study also suggests that egg recognition in relation to spot coloration, like ground colour recognition, is tuned to the natural variation of avian eggshell spot colours but not to unnatural spot colours.

Co-composting of eggshell waste in self-heating reactors: monitoring and end product quality.

Science.gov (United States)

Soares, Micaela A R; Quina, Margarida M J; Quinta-Ferreira, Rosa M

2013-11-01

Industrial eggshell waste (ES) is classified as an animal by-product not intended to human consumption. For reducing pathogen spreading risk due to soil incorporation of ES, sanitation by composting is a pre-treatment option. This work aims to evaluate eggshell waste recycling in self-heating composting reactors and investigate ES effect on process evolution and end product quality. Potato peel, grass clippings and rice husks were the starting organic materials considered. The incorporation of 30% (w/w) ES in a composting mixture did not affect mixture biodegradability, nor its capacity to reach sanitizing temperatures. After 25 days of composting, ES addition caused a nitrogen loss of about 10 g N kg(-1) of initial volatile solids, thus reducing nitrogen nutritional potential of the finished compost. This study showed that a composting mixture with a significant proportion of ES (30% w/w) may be converted into calcium-rich marketable compost to neutralize soil acidity and/or calcium deficiencies. Copyright © 2013 Elsevier Ltd. All rights reserved.

Eggshell membrane as a novel bio sorbent for remediation of boron from desalinated water.

Science.gov (United States)

Al-Ghouti, Mohammad A; Khan, Mariam

2018-02-01

This study investigated the use of eggshell membrane (ESM) as a bio-sorbent and the effect of temperature, pH, and initial concentration on its efficiency. Furthermore, by altering the chemical composition, modified eggshell membrane (MESM) was prepared, and its efficiency was compared with the ESM. Results showed that the adsorption of boron preferred an acidic condition; pH 6 at 35 °C. In addition, the positive value of ΔH° suggested that the reaction favored endothermic pathway, while the negative value for ΔG° further suggested that the adsorption process was spontaneous. Furthermore, the ESM could adsorb 97% of boron, while MESM was able to adsorb 95%. From the Fourier transform infrared (FTIR), different functional groups were recorded on the surface of the ESM and MESM, and they played key role in the boron adsorption mechanisms. Linear Freundlich model was suggested to best describe the experimental data with 99.4% correlation coefficient. Copyright © 2017 Elsevier Ltd. All rights reserved.

Comparison of laser welds in thick section S700 high-strength steel manufactured in flat (1G) and horizontal (2G) positions

OpenAIRE

Guo, Wei; Liu, Qiang; Francis, John Anthony; Crowther, Dave; Thompson, Alan; Liu, Zhu; Li, Lin

2015-01-01

Lack of penetration, undercut and melt sagging are common welding defects for single-pass laser welds in thick plates, particularly when using a traditional 1G welding position (laser directed towards ground). This investigation shows, for the first time, that welding 13 mm thick high-strength S700 steel plates in the 2G position (laser beam perpendicular to the direction of gravity) can mitigate some of the common welding defects including undercut and sagging. A computational fluid dynamic ...

Decline in snail abundance due to soil acidification causes eggshell defects in forest passerines

NARCIS (Netherlands)

Graveland, J; vanderWal, R

On poor soils in the Netherlands an increasing number of great tits, Parus major, and of other forest passerines produce eggs with defective shells and have low reproductive success as a result of calcium deficiency. A similar increase in eggshell defects has been observed in Germany and Sweden.

Decline in snail abundance due to soil acidification causes eggshell defects in forest passerines

NARCIS (Netherlands)

Graveland, J.; Van der Wal, R.

1996-01-01

On poor soils in the Netherlands an increasing number of great tits, Parus major, and of other forest passerines produce eggs with defective shells and have low reproductive success as a result of calcium deficiency. A similar increase in eggshell defects has been observed in Germany and Sweden.

A case of radiation enteritis with perforated peritonitis caused by a piece of eggshell

International Nuclear Information System (INIS)

Kitamura, Hirotaka; Maeda, Kazuya; Miyanaga, Tamonn; Doden, Kenji; Hattori, Masakazu; Hashizume, Yasuo

2011-01-01

The patient was a woman in her sixties who had received radiation therapy for cancer of uterine cervix 7 years earlier and had been suffering from diarrhea for these several years. The patient was seen at our emergency clinic because of a 5 hour-history of lower abdominal pain at the beginning of July 2010. An abdominal CT scan showed free air and ascites. A high density structure 1.5 cm in size was identified within the small intestine, but its relation with the perforation was obscure. Emergency operation was done with the most likely diagnosis of intestinal perforation and general peritonitis. When the lower abdomen was opened by midline incision, about 200 ml of cloudy ascites was observed and the ileum became white in color and hard resulting from the radiation therapy. A perforation was identified in the ileum about 15 cm distant from the ileocecal valve, and a 1.5-cm sized thin and hard material was palpated within the intestine at the same portion. Ilececal resection including the perforated portion was performed and functional end-to-end anastomosis was made at a grossly normal area. There was a piece of eggshell 1.5-cm in size in the perforated portion in the resected specimen. From this together with histopathologial findings, perforation of the small intestine caused by a piece of eggshell associated with radiation enteritis was finally diagnosed. Small bowel perforation must be kept in mind as a possible late complication of radiation therapy, however, no cases of small bowel perforation caused by eggshell have been reported so far. This rare case is reported here, with a review of the literature. (author)

Eggshell bacterial load is related to antimicrobial properties of feathers lining barn swallow nests.

Science.gov (United States)

Peralta-Sánchez, Juan Manuel; Soler, Juan José; Martín-Platero, Antonio Manuel; Knight, Rob; Martínez-Bueno, Manuel; Møller, Anders Pape

2014-02-01

The use of feathers to line bird's nests has traditionally been interpreted as having a thermoregulatory function. Feather-degrading bacteria growing on feathers lining nests may have antimicrobial properties, which may provide an additional benefit to lining nests with feathers. We test the hypothesis that the production of antimicrobial substances by feather bacteria affects the microbiological environment of the nest, and therefore the bacterial density on eggshells and, indirectly, hatching success. These effects would be expected to differ between nests lined with pigmented and white feathers, because bacteria grow differently on feathers of different colors. We experimentally manipulated the composition of pigmented and unpigmented feathers in nests of the barn swallow (Hirundo rustica) and studied the antimicrobial properties against the keratin-degrading bacterium Bacillus licheniformis of bacteria isolated from feathers of each color. Analyzed feathers were collected at the end of the incubation period, and antimicrobial activity was defined as the proportion of bacteria from the feathers that produce antibacterial substances effective against B. licheniformis. Our experimental manipulation affected antimicrobial activity, which was higher in nests with only white feathers at the beginning of incubation. Moreover, white feathers showed higher antimicrobial activity than black ones. Interestingly, antimicrobial activity in feathers of one of the colors correlated negatively with bacterial density on feather of the opposite color. Finally, antimicrobial activity of white feathers was negatively related to eggshell bacterial load. These results suggest that antimicrobial properties of feathers in general and of white feathers in particular affect the bacterial environment in nests. This environment in turn affects the bacterial load on eggshells, which may affect hatching success.

Carbonized chicken eggshell membranes with 3D architectures as high-performance electrode materials for supercapacitors

Energy Technology Data Exchange (ETDEWEB)

Li, Zhi; Zhang, Li; Amirkhiz, Babak Shalchi; Tan, Xuehai; Xu, Zhanwei; Wang, Huanlei; Olsen, Brian C.; Holt, Chris M.B.; Mitlin, David [Chemical and Materials Engineering, University of Alberta, Edmonton, AB (Canada); National Institute for Nanotechnology (NINT), NRC, Edmonton, AB (Canada)

2012-04-15

Supercapacitor electrode materials are synthesized by carbonizing a common livestock biowaste in the form of chicken eggshell membranes. The carbonized eggshell membrane (CESM) is a three-dimensional macroporous carbon film composed of interwoven connected carbon fibers containing around 10 wt% oxygen and 8 wt% nitrogen. Despite a relatively low surface area of 221 m{sup 2} g{sup -1}, exceptional specific capacitances of 297 F g{sup -1} and 284 F g{sup -1} are achieved in basic and acidic electrolytes, respectively, in a 3-electrode system. Furthermore, the electrodes demonstrate excellent cycling stability: only 3% capacitance fading is observed after 10 000 cycles at a current density of 4 A g{sup -1}. These very attractive electrochemical properties are discussed in the context of the unique structure and chemistry of the material. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Effects of inositol, inositol-generating phytase B applied alone, and in combination with 6-phytase A to phosphorus-deficient diets on laying performance, eggshell quality, yolk cholesterol, and fatty acid deposition in laying hens.

Science.gov (United States)

Zyla, K; Mika, M; Duliński, R; Swiatkiewicz, S; Koreleski, J; Pustkowiak, H; Piironen, J

2012-08-01

Phytase B, a product of Aspergillus niger phyB gene expressed in Trichoderma reesei, which increased myo-inositol concentrations in 20 mM sodium phytate solution 7.5-fold during 120-min incubation, a combination of phytase B with 6-phytase A, and pure myo-inositol were tested as feed supplements in Bovans Brown laying hens. In the 2-factorial experiment (2×5), birds from wk 50 to 62 were fed 2 basal diets, corn-soybean (CSM) or wheat-soybean (WSM), using 12 one-hen cages per treatment. For both basal diets, the dietary treatments included negative control (0.08% nonphytate P in CSM, 0.13% nonphytate P in WSM; NC); internal control groups, NC+0.04% nonphytate P from monocalcium phosphate, MCP (IC); NC+0.1% of myo-inositol (Inos), NC+phytase B at 1,300 units of phytase B-acid phosphatase activity (AcPU)/kg (PhyB), NC+phytase B at 1,300 AcPU/kg+6-phytase A at 300 FTU/kg (PhyA+B). Feed intake, laying performance, and eggshell quality were determined. The total lipid and cholesterol contents as well as fatty acid profile were assessed in egg yolks collected from hens fed CSM diets, as was fatty acid profile. The hens fed the WSM diet consumed significantly more feed, laid a higher mass of eggs daily with higher mean weights, and had a higher hen-day egg production than the birds receiving the CSM diets. Similarly, higher values for yolk weights, shell weights, shell thickness, shell density, and breaking strengths were determined in the eggs laid by the hens fed the WSM diets. In hens fed either the CSM diets with phytase B alone, or in combination with 6-phytase A, enhanced feed intakes, egg mass, and hen-day egg production were recorded. Phytases also enhanced the eggshell quality parameters in the hens fed both variants of the diets. Phytase B alone, or in combination with 6-phytase A, reduced the total lipid and cholesterol concentrations in egg yolks collected from the hens fed the CSM diets, whereas the combination of both phytases improved the n-6:n-3

Optimization of aluminum thickness for absorption of undesired Ti K X-rays in the measurement of low energy brachytherapy source strength

Energy Technology Data Exchange (ETDEWEB)

Kashian, S., E-mail: skashian@aeoi.org.ir [Radiation Applications Research School, Nuclear Science and Technology Research Institute, Tehran (Iran, Islamic Republic of); Physics Department, Shiraz University, Shiraz 71454 (Iran, Islamic Republic of); Raisali, G., E-mail: graisali@aeoi.org.ir [Radiation Applications Research School, Nuclear Science and Technology Research Institute, Tehran (Iran, Islamic Republic of); Eskandari, M.R., E-mail: eskandari@susc.ac.ir [Physics Department, Shiraz University, Shiraz 71454 (Iran, Islamic Republic of); Nuclear Engineering Department, Shiraz University, Shiraz (Iran, Islamic Republic of); Khalafi, H., E-mail: hkhalafi@aeoi.org.ir [Radiation Applications Research School, Nuclear Science and Technology Research Institute, Tehran (Iran, Islamic Republic of)

2011-02-15

The contribution of Ti K X-rays to total air kerma strength for low energy brachytherapy sources ({sup 125}I and {sup 103}Pd) are calculated for different source-to-aperture distances of an indigenously designed free air ionization chamber. For 30 cm source-to-aperture distance, calculated contribution of Ti K X-rays is 4%. The Ti K X-rays can be eliminated by a relatively thin aluminum filter, but the primary photons emitted by the source will also be attenuated. This effect should be compensated by applying a suitable correction factor. The uncertainty in the attenuation correction factor has been also calculated for different thicknesses of aluminum by a Monte Carlo uncertainty analysis algorithm programmed in FORTRAN. The results show that the optimum thickness of the aluminum absorber is 100 {mu}m, for which the contribution of Ti K X-rays in air kerma strength is reduced to less than one hundredth of the uncertainty in the correction factor, ensuring that the uncertainty in the air kerma strength will be mainly due to the uncertainty in the correction factor. The calculated uncertainties are 1.7 x 10{sup -3}, and 3.4 x 10{sup -3} for {sup 125}I and {sup 103}Pd sources, respectively.

Catalytic wet air oxidation of coke-plant wastewater on ruthenium-based eggshell catalysts in a bubbling bed reactor.

Science.gov (United States)

Yang, M; Sun, Y; Xu, A H; Lu, X Y; Du, H Z; Sun, C L; Li, C

2007-07-01

Catalytic wet air of coke-plant wastewater was studied in a bubbling bed reactor. Two types of supported Ru-based catalysts, eggshell and uniform catalysts, were employed. Compared with the results in the wet air oxidation of coke-plant wastewater, supported Ru uniform catalysts showed high activity for chemical oxygen demand (COD) and ammonia/ammonium compounds (NH3-N) removal at temperature of 250 degrees C and pressure of 4.8 MPa, and it has been demonstrated that the catalytic activity of uniform catalyst depended strongly on the distribution of active sites of Ru on catalyst. Compared to the corresponding uniform catalysts with the same Ru loading (0.25 wt.% and 0.1 wt.%, respectively), the eggshell catalysts showed higher activities for CODcr removal and much higher activities for NH3-N degradation. The high activity of eggshell catalyst for treatment of coke-plant wastewater can be attributed to the higher density of active Ru sites in the shell layer than that of the corresponding uniform catalyst with the same Ru loading. It has been also evidenced that the active Ru sites in the internal core of uniform catalyst have very little or no contribution to CODcr and NH3-N removal in the total oxidation of coke-plant wastewater.

Development of glucose biosensor based on ZnO nanoparticles film and glucose oxidase-immobilized eggshell membrane

Directory of Open Access Journals (Sweden)

Bohari Noor Aini

2015-06-01

Full Text Available A novel electrochemical glucose biosensor was developed by depositing an ionic liquid (IL (e.g., 1-ethyl-3-methylimidazolium trifluoromethanesulfonate; [EMIM][Otf], ZnO nanoparticles (ZnONPs and eggshell membrane (ESM on a modified glassy carbon electrode (GCE for determination of glucose. Glucose oxidase (GOx was covalently immobilized on eggshell membrane with glutaraldehyde as a cross-linker. Methylene blue was used as a redox indicator to enhance the electron transfer capacity and to ensure stability of both the oxidized and reduced forms in the reaction of enzyme and substrate. The morphological characteristics of microstructures eggshell membranes, chitosan, GOx/ESM, GOx/ZnONPs/IL/ESM and GOx/ZnONPs-IL/CHIT were observed using scanning electron microscopy (SEM. The effects of scan rate, time and pH on the response of glucose biosensors were studied in detail. Under optimal conditions (pH 6.5, 50 s, cyclic voltammetry showed different glucose concentrations on the range of 1 × 10−12 to 0.6 M, with a detection limit of 1 × 10−13 M. The GOx/ZnONPs/IL/ESM was found to be more sensitive as compared to GOx/ZnONPs-IL/CHIT. This developed glucose biosensor detection approach has several advantages such as fast, simple and convenient method, sensitivity, low cost, eco-friendly, low concentrations and remarkable catalytic activities of current signals during glucose reaction.

The Effects of Double Oscillation Exercise Combined with Elastic Band Exercise on Scapular Stabilizing Muscle Strength and Thickness in Healthy Young Individuals: A Randomized Controlled Pilot Trial

Directory of Open Access Journals (Sweden)

Jieun Cho, Kyeongbong Lee, Minkyu Kim, Joohee Hahn, Wanhee Lee

2018-03-01

Full Text Available This study aimed to investigate the effect of double oscillation exercise combined with elastic band exercise on the strength and thickness ratio of the scapular stabilizing muscles in healthy young individuals. A total of 30 subjects (17 male, 13 female were randomly assigned to an elastic band exercise group (EBG (n = 15 or an elastic band plus double oscillation exercise group (EB-DOG (n = 15. A total of 28 subjects completed the experiment and evaluation. Patients in the EBG performed the elastic band exercise for shoulder flexion, extension, abduction, adduction, horizontal abduction/adduction, and internal/external rotation for 30 minutes/session, five times/week, for four weeks. Patients in the EB-DOG performed the elastic band exercise for 15 minutes and the double oscillation exercise in three planes of motion (frontal, sagittal, and transverse, using a Bodyblade® for 15 minutes/session, five times/week, for four weeks. Shoulder muscle strength was assessed using a manual muscle test device during maximal voluntary isometric contraction (MVIC, while the thicknesses of the scapular stabilizing muscles were assessed using rehabilitative ultrasound imaging both at rest and during MVIC. Both groups had significant effects on shoulder muscle strength, however, there was no significant difference between the two groups for change value of shoulder muscle strength (Bonferroni correction p < 0.005. Significant differences were observed in the group × time interactions for horizontal abduction, external rotation, and protraction. There was a statistically significant improvement in thickness ratio of LT and SA in the EB-DOG and no significant difference was founded in EBG (Bonferroni correction p < 0.006. In comparison between the two groups, EB-DOG showed a significant change in the thickness ratio of LT compared to EBG. In addition, significant differences were observed for the group × time interactions for the thickness ratio of the LT (F

Solutions for Safe Hot Coil Evacuation and Coil Handling in Case of Thick and High Strength Steel

Directory of Open Access Journals (Sweden)

Sieberer Stefan

2016-01-01

Full Text Available Currently hot rolling plants are entering the market segment for thick gauges and high strength steel grades where the elastic bending property of the strip leads to internal forces in the coil during coiling operation. The strip tends to open. Primetals is investigating several possibilities to facilitate safe coil evacuation and coil handling under spring-back conditions. The contribution includes finite element models of such mechanical solutions. Results of parameter variation and stability limits of case studies are presented in the paper.

Effect of storage duration on the rheological properties of goose liquid egg products and eggshell membranes

Czech Academy of Sciences Publication Activity Database

Kumbár, V.; Nedomová, Š.; Trnka, Jan; Buchar, J.; Pytel, R.

2016-01-01

Roč. 95, č. 7 (2016), s. 1693-1701 ISSN 0032-5791 Institutional support: RVO:61388998 Keywords : egg yolk * albumen * liquid whole egg * rheology * eggshell membrane Subject RIV: BO - Biophysics Impact factor: 1.908, year: 2016 http://ps.oxfordjournals.org/

Maximizing coupling strength of magnetically anchored surgical instruments: how thick can we go?

Science.gov (United States)

Best, Sara L; Bergs, Richard; Gedeon, Makram; Paramo, Juan; Fernandez, Raul; Cadeddu, Jeffrey A; Scott, Daniel J

2011-01-01

The Magnetic Anchoring and Guidance System (MAGS) includes an external magnet that controls intra-abdominal surgical instruments via magnetic attraction forces. We have performed NOTES (Natural Orifice Transluminal Endoscopic Surgery) and LESS (Laparoendoscopic Single Site) procedures using MAGS instruments in porcine models with up to 2.5-cm-thick abdominal walls, but this distance may not be sufficient in some humans. The purpose of this study was to determine the maximal abdominal wall thickness for which the current MAGS platform is suitable. Successive iterations of prototype instruments were developed; those evaluated in this study include external (134-583 g, 38-61 mm diameter) and internal (8-39 g, 10-22 mm diameter) components using various grades, diameters, thicknesses, and stacking/shielding/focusing configurations of permanent Neodymium-iron-boron (NdFeB) magnets. Nine configurations were tested for coupling strength across distances of 0.1-10 cm. The force-distance tests across an air medium were conducted at 0.5-mm increments using a robotic arm fitted with a force sensor. A minimum theoretical instrument drop-off (decoupling) threshold was defined as the separation distance at which force decreased below the weight of the heaviest internal component (39 g). Magnetic attraction forces decreased exponentially over distance. For the nine configurations tested, the average forces were 3,334 ± 1,239 gf at 0.1 cm, 158 ± 98 gf at 2.5 cm, and 8.7 ± 12 gf at 5 cm; the drop-off threshold was 3.64 ± 0.8 cm. The larger stacking configurations and magnets yielded up to a 592% increase in attraction force at 2.5 cm and extended the drop-off threshold distance by up to 107% over single-stack anchors. For the strongest configuration, coupling force ranged from 5,337 gf at 0.1 cm to 0 gf at 6.95 cm and yielded a drop-off threshold distance of 4.78 cm. This study suggests that the strongest configuration of currently available MAGS instruments is suitable for

Normalization of Impact Energy by Laminate Thickness for Compression After Impact Testing

Science.gov (United States)

Nettles, A. T.; Hromisin, S. M.

2013-01-01

The amount of impact energy used to damage a composite laminate is a critical parameter when assessing residual strength properties. The compression after impact (CAI) strength of impacted laminates is dependent upon how thick the laminate is and this has traditionally been accounted for by normalizing (dividing) the impact energy by the laminate's thickness. However, when comparing CAI strength values for a given lay-up sequence and fiber/resin system, dividing the impact energy by the specimen thickness has been noted by the author to give higher CAI strength values for thicker laminates. A study was thus undertaken to assess the comparability of CAI strength data by normalizing the impact energy by the specimen thickness raised to a power to account for the higher strength of thicker laminates. One set of data from the literature and two generated in this study were analyzed by dividing the impact energy by the specimen thickness to the 1, 1.5, 2, and 2.5 powers. Results show that as laminate thickness and damage severity decreased, the value which the laminate thickness needs to be raised to in order to yield more comparable CAI data increases.

Composite Superabsorbent Hydrogel of Acrylic Copolymer and Eggshell: Effect of Biofiller Addition

OpenAIRE

Queirós, Marcos Vinícius A.; Bezerra, Maslândia N.; Feitosa, Judith P. A.

2017-01-01

Eggshell (ES) is an abundant waste material which is mainly composed of calcium carbonate. A superabsorbent hydrogel composite based on poly(acrylamide-co-potassium acrylate) as matrix containing 17 wt.% of chicken ES powder as a filler was synthesized and compared with the gel without filler. The characterization was carried out by Fourier transform infrared (FTIR), scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM/EDX), thermogravimetric analysis (TGA), X-ray diffr...

Data set for the proteomic inventory and quantitative analysis of chicken uterine fluid during eggshell biomineralization

Directory of Open Access Journals (Sweden)

Pauline Marie

2014-12-01

Full Text Available Chicken eggshell is the protective barrier of the egg. It is a biomineral composed of 95% calcium carbonate on calcitic form and 3.5% organic matrix proteins. Mineralization process occurs in uterus into the uterine fluid. This acellular fluid contains ions and organic matrix proteins precursors which are interacting with the mineral phase and control crystal growth, eggshell structure and mechanical properties. We performed a proteomic approach and identified 308 uterine fluid proteins. Gene Ontology terms enrichments were determined to investigate their potential functions. Mass spectrometry analyses were also combined to label free quantitative analysis to determine the relative abundance of 96 proteins at initiation, rapid growth phase and termination of shell calcification. Sixty four showed differential abundance according to the mineralization stage. Their potential functions have been annotated. The complete proteomic, bioinformatic and functional analyses are reported in Marie et al., J. Proteomics (2015 [1].

Chicken eggshells (Gallus gallus domesticus) as carbonate calcium source for biomaterials production; Casca de ovo de galinha caipira (gallus gallus domesticus), como fonte de carbonato de calcio para producao de biomateriais

Energy Technology Data Exchange (ETDEWEB)

Junior, E.A. de O.; Bastos, J.S.B.; Silva, R.C. de S.; Macedo, H.R.A.; Macedo, M. O.C.; Bradim, A.S., E-mail: angelcassiasasilva@gmail.com [Instituto Federal de Educacao, Ciencia e Tecnologia do Piaui (FIPI), PI (Brazil)

2016-07-01

The eggshells present high levels of calcium carbonate. Calcium carbonate obtained from eggshells has been used in the production of biomaterials with applications in bone regeneration, since it is biocompatible. In this work, calcium carbonate was obtained from eggshells to prepare a composite biomaterial. The presence of calcium carbonate bands was observed through spectrometry in the infrared region. Scanning electron microscopy showed the presence of calcium carbonate particles with different sizes and shapes. Carbonate predominance in the form of calcite was also observed through the X-ray diffraction.

Ultrasound-assisted green economic synthesis of hydroxyapatite nanoparticles using eggshell biowaste and study of mechanical and biological properties for orthopedic applications.

Science.gov (United States)

Ingole, Vijay H; Hany Hussein, Kamal; Kashale, Anil A; Ghule, Kalyani; Vuherer, Tomaž; Kokol, Vanja; Chang, Jia-Yaw; Ling, Yong-Chien; Vinchurkar, Aruna; Dhakal, Hom N; Ghule, Anil V

2017-11-01

Nanostructured hydroxyapatite (HAp) is the most favorable candidate biomaterial for bone tissue engineering because of its bioactive and osteoconductive properties. Herein, we report for the first time ultrasound-assisted facile and economic approach for the synthesis of nanocrystalline hydroxyapatite (Ca 10 (PO 4 ) 6 (OH) 2 ) using recycled eggshell biowaste referred as EHAp. The process involves the reaction of eggshell biowaste as a source of calcium and ammonium dihydrogen orthophosphate as a phosphate source. Ultrasound-mediated chemical synthesis of hydroxyapatite (HAp) is also carried out using similar approach wherein commercially available calcium hydroxide and ammonium dihydrogen orthophosphate were used as calcium and phosphate precursors, respectively and referred as CHAp for better comparison. The prepared materials were characterized by X-ray diffraction, field emission scanning electron microscopy, Fourier transform infrared spectroscopy, and Raman spectroscopy to determine crystal structure, particle morphology, and the presence of chemical functional groups. The nanocrystalline EHAp and CHAp were observed to have spherical morphology with uniform size distribution. Furthermore, mechanical properties such as Vickers hardness, fracture toughness, and compression tests have been studied of the EHAp and CHAp samples showing promising results. Mechanical properties show the influence of calcination at 600°C EHAp and CHAp material. After calcination, in the case of EHAp material an average hardness, mechanical strength, elastic modulus, and fracture toughness were found 552 MPa, 46.6 MPa, 2824 MPa, and 3.85 MPa m 1/2 , respectively, while in the case of CHAp 618 MPa, 47.5 MPa, 2071 MPa, and 3.13 MPa m 1/2 . In vitro cell studies revealed that the EHAp and CHAp nanoparticles significantly increased the attachment and proliferation of the hFOB cells. Here, we showed that EHAp and CHAp provide promising biocompatible materials that do not affect the cell

The use of nano-sized eggshell powder for calcium fortification of cow?s and buffalo?s milk yogurts.

Science.gov (United States)

El-Shibiny, Safinaze; El-Gawad, Mona Abd El-Kader Mohamed Abd; Assem, Fayza Mohamed; El-Sayed, Samah Mosbah

2018-01-01

Calcium is an essential element for the growth, activity, and maintenance of the human body. Eggshells are a waste product which has received growing interest as a cheap and effective source of dietary calcium. Yogurt is a food which can be fortified with functional additives, including calcium. The aim of this study was to produce yogurt with a high calcium content by fortification with nano-sized eggshell powder (nano-ESP). Nano-sized ESP was prepared from pre-boiled and dried eggshell, using a ball mill. Yogurt was prepared from cow’s milk supplemented with 3% skimmed milk powder, and from buffalo’s milk fortified with 0.1, 0.2 and 0.3% and 0.1, 0.3 and 0.5% nano-ESP respectively. Electron microscopic transmission showed that the powder consisted of nano-sized crystalline struc- tures (~10 nm). Laser scattering showed that particles followed a normal distribution pattern with z-average of 590.5 nm, and had negative zeta-potential of –9.33 ±4.2 mV. Results regarding changes in yogurt composi- tion, acid development, calcium distribution, biochemical changes, textural parameters and sensory attributes have been presented and discussed. The addition of up to 0.3% nano-ESP made cow and buffalo high-calcium yogurts with an acceptable composition and quality. High-calcium yogurt may offer better health benefits, such as combating osteoporosis.

Optical illusions in scanning electron micrographs: the case of the eggshell of Acrosternum (Chinavia) marginatum (Hemiptera: Pentatomidae).

Science.gov (United States)

Wolf, Klaus W; Reid, Walton; Schrauf, Michael

2003-01-01

Scanning electron microscopy revealed that-as is common in this family of the Hemiptera-the eggs of the green stink bug Acrosternum (Chinavia) marginatum are roughly barrel-shaped and possess at their apical pole a row of slender extensions, the aero-micropylar processes. The outer surface of the eggshell carries hexagonally arranged pits. The analysis of cross-fractured eggshells showed that the pits have slender basal extensions with transverse diaphragms. When scanning electron micrographs of the egg surface of A. marginatum are viewed upside down, the perception flips and the pits appear as elevations to all observers addressed. Thus, we are dealing with an optical illusion, which is known as the 'shape-from-shading effect'. The perceived dents remain robust to changes in the angle of recording (zero to ca. 60 degrees tilt), the magnification (ca. x100 to x1400), and the number of pits included in the micrograph (one to several hundred). When through appropriate positioning of the specimen under the electron beam, contrast is significantly reduced and the distinct shadows at the slope of the pits are eliminated, the optical illusion does not appear. It is inferred that shades provide the decisive clue that determines whether bumps or dents will be perceived. Owing to the low resolution of their compound eyes, the shape-from-shading effect on the eggshell of the bug is in all likelihood not perceived by insects.

An analysis of the pull strength behaviors of fine-pitch, flip chip solder interconnections using a Au-Pt-Pd thick film conductor on Low-Temperature, Co-fired Ceramic (LTCC) substrates

International Nuclear Information System (INIS)

Uribe, Fernando R.; Kilgo, Alice C.; Grazier, John Mark; Vianco, Paul Thomas; Zender, Gary L.; Hlava, Paul Frank; Rejent, Jerome Andrew

2008-01-01

The assembly of the BDYE detector requires the attachment of sixteen silicon (Si) processor dice (eight on the top side; eight on the bottom side) onto a low-temperature, co-fired ceramic (LTCC) substrate using 63Sn-37Pb (wt.%, Sn-Pb) in a double-reflow soldering process (nitrogen). There are 132 solder joints per die. The bond pads were gold-platinum-palladium (71Au-26Pt-3Pd, wt.%) thick film layers fired onto the LTCC in a post-process sequence. The pull strength and failure modes provided the quality metrics for the Sn-Pb solder joints. Pull strengths were measured in both the as-fabricated condition and after exposure to thermal cycling (-55/125 C; 15 min hold times; 20 cycles). Extremely low pull strengths--referred to as the low pull strength phenomenon--were observed intermittently throughout the product build, resulting in added program costs, schedule delays, and a long-term reliability concern for the detector. There was no statistically significant correlation between the low pull strength phenomenon and (1) the LTCC 'sub-floor' lot; (2) grit blasting the LTCC surfaces prior to the post-process steps; (3) the post-process parameters; (4) the conductor pad height (thickness); (5) the dice soldering assembly sequence; or (5) the dice pull test sequence. Formation of an intermetallic compound (IMC)/LTCC interface caused by thick film consumption during either the soldering process or by solid-state IMC formation was not directly responsible for the low-strength phenomenon. Metallographic cross sections of solder joints from dice that exhibited the low pull strength behavior, revealed the presence of a reaction layer resulting from an interaction between Sn from the molten Sn-Pb and the glassy phase at the TKN/LTCC interface. The thick film porosity did not contribute, explicitly, to the occurrence of reaction layer. Rather, the process of printing the very thin conductor pads was too sensitive to minor thixotropic changes to ink, which resulted in

An analysis of the pull strength behaviors of fine-pitch, flip chip solder interconnections using a Au-Pt-Pd thick film conductor on Low-Temperature, Co-fired Ceramic (LTCC) substrates.

Energy Technology Data Exchange (ETDEWEB)

Uribe, Fernando R.; Kilgo, Alice C.; Grazier, John Mark; Vianco, Paul Thomas; Zender, Gary L.; Hlava, Paul Frank; Rejent, Jerome Andrew

2008-09-01

The assembly of the BDYE detector requires the attachment of sixteen silicon (Si) processor dice (eight on the top side; eight on the bottom side) onto a low-temperature, co-fired ceramic (LTCC) substrate using 63Sn-37Pb (wt.%, Sn-Pb) in a double-reflow soldering process (nitrogen). There are 132 solder joints per die. The bond pads were gold-platinum-palladium (71Au-26Pt-3Pd, wt.%) thick film layers fired onto the LTCC in a post-process sequence. The pull strength and failure modes provided the quality metrics for the Sn-Pb solder joints. Pull strengths were measured in both the as-fabricated condition and after exposure to thermal cycling (-55/125 C; 15 min hold times; 20 cycles). Extremely low pull strengths--referred to as the low pull strength phenomenon--were observed intermittently throughout the product build, resulting in added program costs, schedule delays, and a long-term reliability concern for the detector. There was no statistically significant correlation between the low pull strength phenomenon and (1) the LTCC 'sub-floor' lot; (2) grit blasting the LTCC surfaces prior to the post-process steps; (3) the post-process parameters; (4) the conductor pad height (thickness); (5) the dice soldering assembly sequence; or (5) the dice pull test sequence. Formation of an intermetallic compound (IMC)/LTCC interface caused by thick film consumption during either the soldering process or by solid-state IMC formation was not directly responsible for the low-strength phenomenon. Metallographic cross sections of solder joints from dice that exhibited the low pull strength behavior, revealed the presence of a reaction layer resulting from an interaction between Sn from the molten Sn-Pb and the glassy phase at the TKN/LTCC interface. The thick film porosity did not contribute, explicitly, to the occurrence of reaction layer. Rather, the process of printing the very thin conductor pads was too sensitive to minor thixotropic changes to ink, which resulted in

Comparison of Thermal Stability of Dry High-strength Concrete and Wet High-strength Concrete

Science.gov (United States)

Musorina, Tatiana; Katcay, Aleksandr; Selezneva, Anna; Kamskov, Victor

2018-03-01

High-strength concrete is a modern material, which occupies it`s own niche on the construction material market. It is applicable in a large-scale high-rise construction, particularly an underground construction is a frequently used solution for a space saving. Usually underground structure is related to a wet usage environment. Though not all properties of the high-strength concrete are investigated to the full extent. Under adverse climatic conditions of the Russian Federation one of the most important properties for constructional materials is a thermal capacity. Therefore, the main purpose of the paper is to compare a thermal capacity of the high-strength concrete in humid conditions and a thermal capacity of the high-strength concrete in dry operational condition. During the study dependency between thermal capacity and design wall thickness and ambient humidity has to be proven with two experiments. As a result the theoretical relation between thermal capacity characteristic - thermal inertia and wall thickness and ambient humidity was confirmed by the experimental data. The thermal capacity of a building is in direct ratio to the construction thickness. It follows from the experiments and calculations that wet high-strength concrete has less thermal stability.

Revealing the Maximum Strength in Nanotwinned Copper

DEFF Research Database (Denmark)

Lu, L.; Chen, X.; Huang, Xiaoxu

2009-01-01

boundary–related processes. We investigated the maximum strength of nanotwinned copper samples with different twin thicknesses. We found that the strength increases with decreasing twin thickness, reaching a maximum at 15 nanometers, followed by a softening at smaller values that is accompanied by enhanced...

Synthesis of mesh-shaped calcia partially stabilized zirconia using eggshell membrane template as filler composite

Directory of Open Access Journals (Sweden)

Gema Gempita

2017-08-01

Full Text Available This experiment was conducted experimentally to synthesize Calcia Partially Stabilized Zirconia (Ca-PSZ by sol-gel method using eggshell membrane template as a composite filler. The eggshell membrane was used to produce a mesh shaped structure, which hopefully can improve the mechanical properties of the composite. Ca-PSZ filler was synthesized from ZrOCl2 precursor and Ca(NO32 stabilizer with a 24 hours immersion time. Ca-PSZ of synthesis then mixed with the resin matrix to test its composite hardness. The EDS characterization results suggested that the sample contained elements of zirconia, calcium, and oxygen. Whereas, the XRD characterization identified that crystal structures that formed in the sample were nano scale tetragonal. Characterization of SEM showed Ca-PSZ with mesh structured. The average composite hardness value was 15.79 VHN. The composites with Ca-PSZ-synthesized filler could be prepared and its hardness value was higher than the composite with Ca-PSZ filler in spherical particles, but the hardness was still below the composite on the market.

Crushing strength of HTGR fuel particles

International Nuclear Information System (INIS)

Lackey, W.J.; Stinton, D.P.; Davis, L.E.; Beatty, R.L.

1976-01-01

The whole-particle crushing strengths of High-Temperature Gas-Cooled Reactor fertile and fissile coated particles were measured and correlated with fabrication procedures. The crushing strength of Biso-coated fertile particles was increased by the following factors: (1) increasing the outer coating thickness by 10 μm increased strengths by 0.3 lb (1.3 N) for annealed particles and by 0.5 lb (2.2 N) for unannealed particles. (2) An 1800 0 C postcoating anneal increased strengths by 1 lb (4.4 N) for particles with thick outer coatings and by 2 lb (8.9 N) for particles having thin coatings. (3) Increasing the inner coating density by 0.1 g/cm 3 increased strength by 0.6 lb (2.7 N). The crushing strength of Triso-coated fissile particles was proportional to the thickness of the SiC coatings, and strength decreased on annealing by about 0.2 lb (0.9 N) when a porous plate was used to distribute the coating gas and by about 1.5 lb (6.7 N) when a conical gas distributor was used. The strengths of fertile and fissile coated particles as well as uncoated kernels appear adequate to allow fuel fabrication without excessive particle damage

Lithospheric flexural strength and effective elastic thicknesses of the Eastern Anatolia (Turkey) and surrounding region

Science.gov (United States)

Oruç, Bülent; Gomez-Ortiz, David; Petit, Carole

2017-12-01

The Lithospheric structure of Eastern Anatolia and the surrounding region, including the northern part of the Arabian platform is investigated via the analysis and modeling of Bouguer anomalies from the Earth Gravitational Model EGM08. The effective elastic thickness of the lithosphere (EET) that corresponds to the mechanical cores of the crust and lithospheric mantle is determined from the spectral coherence between Bouguer anomalies and surface elevation data. Its average value is 18.7 km. From the logarithmic amplitude spectra of Bouguer anomalies, average depths of the lithosphere-asthenosphere boundary (LAB), Moho, Conrad and basement in the study area are constrained at 84 km, 39 km, 16 km and 7 km, respectively. The geometries of the LAB and Moho are then estimated using the Parker-Oldenburg inversion algorithm. We also present a lithospheric strength map obtained from the spatial variations of EET determined by Yield Stress Envelopes (YSE). The EET varies in the range of 12-23 km, which is in good agreement with the average value obtained from spectral analysis. Low EET values are interpreted as resulting from thermal and flexural lithospheric weakening. According to the lithospheric strength of the Eastern Anatolian region, the rheology model consists of a strong but brittle upper crust, a weak and ductile lower crust, and a weak lower part of the lithosphere. On the other hand, lithosphere strength corresponds to weak and ductile lower crust, a strong upper crust and a strong uppermost lithospheric mantle for the northern part of the Arabian platform.

Diametral tensile strength and film thickness of an experimental dental luting agent derived from castor oil

Directory of Open Access Journals (Sweden)

Juliana Cabrini Carmello

2012-02-01

Full Text Available The need to develop new dental luting agents in order to improve the success of treatments has greatly motivated research. OBJECTIVE: The aim of this study was to evaluate the diametral tensile strength (DTS and film thickness (FT of an experimental dental luting agent derived from castor oil (COP with or without addition of different quantities of filler (calcium carbonate - CaCO3. MATERIAL AND METHODS: Eighty specimens were manufactured (DTS N=40; FT N=40 and divided into 4 groups: Pure COP; COP 10%; COP 50% and zinc phosphate (control. The cements were mixed according to the manufacturers' recommendations and submitted to the tests. The DTS test was performed in the MTS 810 testing machine (10 KN, 0.5 mm/min. For FT test, the cements were sandwiched between two glass plates (2 cm² and a load of 15 kg was applied vertically on the top of the specimen for 10 min. The data were analyzed by means of one-way ANOVA and Tukey's test (α=0.05. RESULTS: The values of DTS (MPa were: Pure COP- 10.94±1.30; COP 10%- 30.06±0.64; COP 50%- 29.87±0.27; zinc phosphate- 4.88±0.96. The values of FT (µm were: Pure COP- 31.09±3.16; COP 10%- 17.05±4.83; COP 50%- 13.03±4.83; Zinc Phosphate- 20.00±0.12. One-way ANOVA showed statistically significant differences among the groups (DTS - p=1.01E-40; FT - p=2.4E-10. CONCLUSION: The experimental dental luting agent with 50% of filler showed the best diametral tensile strength and film thickness.

Technical note: cortical thickness and density estimation from clinical CT using a prior thickness-density relationship

NARCIS (Netherlands)

Humbert, L.; Hazrati Marangalou, J.; Del Río Barquero, L.M.; van Lenthe, G.H.; van Rietbergen, B.

2016-01-01

Purpose: Cortical thickness and density are critical components in determining the strength of bony structures. Computed tomography (CT) is one possible modality for analyzing the cortex in 3D. In this paper, a model-based approach for measuring the cortical bone thickness and density from clinical

Effects of carbohydrase enzyme supplementation on performance, eggshell quality, and bone parameters of laying hens fed on maize- and wheat-based diets.

Science.gov (United States)

Olgun, Osman; Altay, Y; Yildiz, Alp O

2018-04-01

1. This study was conducted to determine the effects of enzyme supplementation of maize/wheat-based diets on the performance, egg quality, and serum and bone parameters of laying hens. 2. During the 12-week experimental period, a total of 72 laying hens aged 52 weeks were randomly distributed among 6 experimental groups. Each experimental group contained 4 replicates, each with three birds. The experiment was a randomised design consisting of a 3 × 2 factorial arrangement, with three levels of wheat substitution and two levels of enzyme (xylanase: 1500.00 U/kg, β-glucanase: 100 000 U/kg, cellulase: 1 000 000 U/kg, α-amylase: 160 000 U/kg) inclusion in the diet. Wheat replaced 0, 50, or 100% of maize with or without 1.0 g/kg enzyme supplementation in iso-nitrogenous and iso-caloric experimental diets. 3. Body weight, egg production, egg weight, egg mass, eggshell thickness, and the feed conversion ratio were adversely affected by the wheat-based diet. The eggshell quality parameters decreased with enzyme supplementation to the diet. 4. Wheat-based diets adversely affected calcium and phosphorus concentrations in the tibia, but the addition of the enzymes to the wheat-based diet prevented the negative effects of wheat-based diets on tibia mineralisation in laying hens. The wheat-based diets tended to reduce plasma mineral contents, and the addition of enzymes tended to affect plasma minerals and biomechanical properties of the tibia positively in laying hens. 5. These results indicate that wheat-based diets in aged laying hens adversely affected the mineral metabolism compared with maize-based diets, and the negative effects of wheat on bone mineralisation can be prevented by enzyme supplementation to the diets in laying hens.

Effects of wheat cultivar, nonphytate phosphorus levels and enzyme ...

African Journals Online (AJOL)

Mahmood

2015-07-22

Jul 22, 2015 ... apparent metabolizable energy (AME), NSP, crude protein (CP) and other chemical ..... Egg specific gravity, eggshell weight, eggshell thickness, albumen height and ... removed and stored at −20 ºC until further analysis.

Increase of calcium and reduction of lactose concentration in milk by treatment with kefir grains and eggshell.

Science.gov (United States)

Fina, Brenda L; Brun, Lucas R; Rigalli, Alfredo

2016-01-01

Dairy products are the main source of calcium (Ca), but the loss of the consumption habit contributes to low consumption in adulthood, which leads to osteoporosis and increased fracture risk. Domestic use of kefir is straightforward and the eggshell is a natural discarded source of Ca. This paper proposes the development of an enriched Ca reduced lactose milk using eggshell and kefir. During the in vitro preparation, the pH, Ca and lactose contents were measured. Ca intestinal absorption of untreated milk and milk with kefir was compared. Finally, human volunteers consumed this dairy product and 24-h urine Ca was measured. Results showed that the beverage has lower lactose and higher Ca than untreated milk and milk with kefir. Intestinal Ca absorption was not different between both milks and an increase in urinary Ca excretion was observed in humans. This study provides a methodology to prepare at home a dairy product that could contribute to improve the Ca intake in adults.

Yield Strength Testing in Human Cadaver Nasal Septal Cartilage and L-Strut Constructs.

Science.gov (United States)

Liu, Yuan F; Messinger, Kelton; Inman, Jared C

2017-01-01

To our knowledge, yield strength testing in human nasal septal cartilage has not been reported to date. An understanding of the basic mechanics of the nasal septum may help surgeons decide how much of an L-strut to preserve and how much grafting is needed. To determine the factors correlated with yield strength of the cartilaginous nasal septum and to explore the association between L-strut width and thickness in determining yield strength. In an anatomy laboratory, yield strength of rectangular pieces of fresh cadaver nasal septal cartilage was measured, and regression was performed to identify the factors correlated with yield strength. To measure yield strength in L-shaped models, 4 bonded paper L-struts models were constructed for every possible combination of the width and thickness, for a total of 240 models. Mathematical modeling using the resultant data with trend lines and surface fitting was performed to quantify the associations among L-strut width, thickness, and yield strength. The study dates were November 1, 2015, to April 1, 2016. The factors correlated with nasal cartilage yield strength and the associations among L-strut width, thickness, and yield strength in L-shaped models. Among 95 cartilage pieces from 12 human cadavers (mean [SD] age, 67.7 [12.6] years) and 240 constructed L-strut models, L-strut thickness was the only factor correlated with nasal septal cartilage yield strength (coefficient for thickness, 5.54; 95% CI, 4.08-7.00; P cadaver nasal septal cartilage, L-strut thickness was significantly associated with yield strength. In a bonded paper L-strut model, L-strut thickness had a more important role in determining yield strength than L-strut width. Surgeons should consider the thickness of potential L-struts when determining the amount of cartilaginous septum to harvest and graft. NA.

Effects of breeder age, broiler strain, and eggshell temperature on development and physiological status of embryos and hatchlings

NARCIS (Netherlands)

Nangsuay, A.; Meijerhof, R.; Anker-Hensen, van den Ilona; Heetkamp, M.J.W.; Souza Morita, De V.; Kemp, B.; Brand, Van Den H.

2016-01-01

Breeder age and broiler strain can influence the availability of nutrients and oxygen, particularly through differences in yolk size and shell conductance. We hypothesized that these egg characteristics might affect embryonic responses to changes in eggshell temperature (EST). This study aimed to

Ras1 interacts with multiple new signaling and cytoskeletal loci in Drosophila eggshell patterning and morphogenesis.

Science.gov (United States)

Schnorr, J D; Holdcraft, R; Chevalier, B; Berg, C A

2001-10-01

Little is known about the genes that interact with Ras signaling pathways to regulate morphogenesis. The synthesis of dorsal eggshell structures in Drosophila melanogaster requires multiple rounds of Ras signaling followed by dramatic epithelial sheet movements. We took advantage of this process to identify genes that link patterning and morphogenesis; we screened lethal mutations on the second chromosome for those that could enhance a weak Ras1 eggshell phenotype. Of 1618 lethal P-element mutations tested, 13 showed significant enhancement, resulting in forked and fused dorsal appendages. Our genetic and molecular analyses together with information from the Berkeley Drosophila Genome Project reveal that 11 of these lines carry mutations in previously characterized genes. Three mutations disrupt the known Ras1 cell signaling components Star, Egfr, and Blistered, while one mutation disrupts Sec61beta, implicated in ligand secretion. Seven lines represent cell signaling and cytoskeletal components that are new to the Ras1 pathway; these are Chickadee (Profilin), Tec29, Dreadlocks, POSH, Peanut, Smt3, and MESK2, a suppressor of dominant-negative Ksr. A twelfth insertion disrupts two genes, Nrk, a "neurospecific" receptor tyrosine kinase, and Tpp, which encodes a neuropeptidase. These results suggest that Ras1 signaling during oogenesis involves novel components that may be intimately associated with additional signaling processes and with the reorganization of the cytoskeleton. To determine whether these Ras1 Enhancers function upstream or downstream of the Egf receptor, four mutations were tested for their ability to suppress an activated Egfr construct (lambdatop) expressed in oogenesis exclusively in the follicle cells. Mutations in Star and l(2)43Bb had no significant effect upon the lambdatop eggshell defect whereas smt3 and dock alleles significantly suppressed the lambdatop phenotype.

Egg-Citing! Isolation of Protoporphyrin IX from Brown Eggshells and Its Detection by Optical Spectroscopy and Chemiluminescence

Science.gov (United States)

Dean, Michelle L.; Miller, Tyson A.; Bruckner, Christian

2011-01-01

A simple and cost-effective laboratory experiment is described that extracts protoporphyrin IX from brown eggshells. The porphyrin is characterized by UV-vis and fluorescence spectroscopy. A chemiluminescence reaction (peroxyoxalate ester fragmentation) is performed that emits light in the UV region. When the porphyrin extract is added as a fluor…

Tungsten thick coatings for plasma facing components

International Nuclear Information System (INIS)

Riccardi, B.; Pizzuto, A.; Orsini, A.; Libera, S.; Visca, E.; Bertamini, L.; Casadei, F.; Severini, E.; Montanari, R.; Litunovsky, N.

1998-01-01

The aim of the R and D activity was to realize thick W coatings on CuCrZr hollow bars and to test the mock ups with respect to thermal fatigue. Eight mock ups provided of 4 mm thick W coating were finally manufactured. The bonding integrity between coating and substrate was checked by means of an Ultrasonic apparatus. Characterisation of coatings was performed in order to assess microstructure, impurity content, density, tensile strength, adhesion strength, thermal conductivity and thermal expansion coefficient. Macroscopic residual strain measurements were performed by means of 'hole drilling' technique. The activities performed demonstrated the feasibility of thick Tungsten coatings on geometries with more complex residual strain distribution. These coatings are reliable armour of medium heat flux plasma facing component. (author)

Tratamento e valorização agrícola da casca de ovo Treatment and agricultural valorization of eggshell

Directory of Open Access Journals (Sweden)

Mª Carmo Magalhães

2011-07-01

Full Text Available Este trabalho tem como objectivo avaliar a possibilidade de utilização da casca de ovo como correctivo alcalinizante, através de ensaios em vasos, bem como estudar o efeito da adição de quantidades significativas deste material (20 a 33% m m-1 quer no desenvolvimento do processo de compostagem, quer na qualidade dos compostos obtidos. Os resultados obtidos sugerem que a aplicação de casca de ovo, com granulometria inferior a 2 mm, ao solo tem um efeito semelhante ao da aplicação de calcário agrícola, apenas o custo associado ao seu tratamento térmico inviabiliza a sua aplicação. Nos estudos de compostagem, a casca de ovo (material inorgânico foi combinada com outros materiais com elevada percentagem de matéria orgânica (aparas de relva, estrume de cavalo e estrume de galinha. O desempenho do processo não foi significativamente afectado pela casca de ovo, mesmo quando esta constituiu cerca de 30% do volume das pilhas, tendo sido sempre atingida a fase termofílica. Os compostos obtidos apresentaram propriedades adequadas para serem aplicados ao solo.This study aims to assess the possibility of using eggshell as a corrective alkalizing, through trials in pots, as well as studying the effect of adding significant amounts of eggshell (20 to 33% m m-1 in the development the composting process, and in the quality of the final composts obtained. The results suggest that the use of eggshell with a particle size below 2 mm in soil has an effect similar to the application of lime, only the cost associated with its thermal treatment prevents its use for this purpose. In studies of composting, the eggshell (inorganic material was combined with other materials with high percentage of organic matter (grass clippings, horse manure and chicken manure. Process performance was not significantly affected by the egg shell, even when it constituted about 30% of the pile volume and thermophilic stage was always achieved. The final composts obtained

Transitional behaviour of thickness effects in shipbuilding materials (MS plate)

Science.gov (United States)

Mahmud, S. M. Ikhtiar; Razib, Amirul Hasan; Rahman, Md. Rabab Raiyatur

2017-12-01

Majority of the crack propagation in ships and offshore structures are caused due to fatigue. Previously, it was known that fatigue strength of notched specimen is dependent on size, but recently it came to light that fatigue strength of some welded joints depends on the thickness. Much investigation is done on the fatigue growth of welded joints. Fatigue often results in fracture accidents, which starts from the sites of structural discontinuities because of the reason that they may induce local stress concentrations. Structural discontinuities include notches, holes, sharp corners, and weld defects. Weld defects include undercut, porosity, lack of fusion, slag inclusion, incomplete weld root penetration, and misalignments. In order to investigate the effects of plate thickness on fatigue strength, semi-elliptical side notches (U and V shaped) in plates are studied in the present research. First consider a simple problem of crack emanating from notches in plates where the solution of stress intensity factor is given by an empirical formula so that the thickness effect on fatigue strength can easily be investigated for a variety of geometrical parameters. The present study aims to investigate the transitional behaviour of thickness effect in plates on fatigue strength. In order to calculate the stress, finite element analysis is carried by using ANSYS.

THE TREATED EGGSHELLS AS A NEW BIOSORBENT FOR ELIMINATION OF CARBARYL PESTICIDE FROM AQUEOUS SOLUTIONS: KINETICS, THERMODYNAMICS AND ISOTHERMS

Directory of Open Access Journals (Sweden)

ABDELHAMID BAKKA

2016-10-01

Full Text Available The efficiency of treated eggshells (TES for removing the carbaryl pesticide from aqueous solutions was examined by biosorption process. Batch mode experiments were conducted using various parameters such as contact time, temperature, biosorbent amount, carbaryl concentration and pH. Removal efficiency of carbaryl by the TES attained 87.35 % after 60 min of contact time, using 10 mg·L-1 of pesticide and 1.5 g·L-1 of biosorbent. The results indicate that Freundlich equation is well described with the carbaryl adsorption, with correlation coefficient R2 value of 0.99. They showed that the biosorption processes were spontaneous and exothermic. The Gibbs energy ∆G increased with increase in temperature indicating an increase in feasibility of biosorption at low temperature. These results show that treated eggshells can be employed as an alternative to commercial adsorbents in the removal of pesticides from aqueous solutions.

Relevance of the Physicochemical Properties of Calcined Quail Eggshell (CaO as a Catalyst for Biodiesel Production

Directory of Open Access Journals (Sweden)

Leandro Marques Correia

2017-01-01

Full Text Available The CaO solid derived from natural quail eggshell was calcined and employed as catalyst to produce biodiesel via transesterification of sunflower oil. The natural quail eggshell was calcined at 900°C for 3 h, in order to modify the calcium carbonate present in its structure in CaO, the activity phase of the catalyst. Both precursor and catalyst were characterized using Hammett indicators method, X-ray fluorescence (XRF, X-ray diffraction (XRD, thermogravimetric analysis (TG/DTG, CO2 temperature-programmed desorption (CO2-TPD, X-ray photoelectronic spectroscopy (XPS, Fourier infrared spectroscopy (FTIR, scanning electron microscopy (SEM, N2 adsorption-desorption at −196°C, and distribution particle size. The maximum biodiesel production was of 99.00 ± 0.02 wt.% obtained in the following transesterification reaction conditions: XMR (sunflower oil/methanol molar ratio of 1 : 10.5 mol : mol, XCAT (catalyst loading of 2 wt.%, XTIME (reaction time of 2 h, stirring rate of 1000 rpm, and temperature of 60°C.

Comparison of cadmium adsorption onto chitosan and epichlorohydrin crosslinked chitosan/eggshell composite

Science.gov (United States)

Rahmi; Marlina; Nisfayati

2018-05-01

The use of chitosan and epichlorohydrin crosslinked chitosan/eggshell composite for cadmium adsorption from water were investigated. The factors affecting adsorption such as pH and contact time were considered. The results showed that the optimum pH of adsorption was pH = 6.0 and the equilibrium time of adsorption was 40 min. The adsorption isotherm of Cd ions onto chitosan and composite were well fitted to Langmuir equation. The maximum adsorption capacity (fitting by Langmuir model) of chitosan and composite were 1.008 and 11.7647 mg/g, respectively. Adsorption performance of composite after regeneration was better than chitosan.

PERFORMANCE AND EGGS QUALITY OF HENS OF GENETIC RESOURCES OF THE CZECH REPUBLIC AND SLOVAKIA

Directory of Open Access Journals (Sweden)

Zdeněk Ledvinka

2015-03-01

Full Text Available The aim of this study was to assess the performance and technological values of eggs of Czech Hen and Oravka breeds housed on litter. The assumption was that the genotype of hens affects their performance, egg weight, and parameters of yolk, albumen and eggshell quality. A total of 30 pullets of Czech Hen breed and 30 pullets of Oravka breed in the age of 17 weeks were included in to the experiment. Environmental conditions corresponded to the standard requirements for laying hens in observed type of housing system. Hen day egg production, egg yield, daily feed consumption per hen, feed consumption per egg and egg weight, egg shape index, proportion and index of yolk and albumen,yolk colour and Haugh units score were monitored in the experiment. From the parameters of eggshell, proportion, thickness, strength and colour of eggshell were observed. Performance parameters of laying hens weren't affected by the genotype of hens. Czech Hen breed showed insignificantly the higher value in all indicators. The significantly (P≤0.01 and P≤0.001 better values of eggshell quality parameters were detected in Czech Hen breed. We found out that Czech Hen breed had also statistically significantly lighter colour of eggshell. There were no significant interbreed differences in egg weight, proportion of yolk and albumen. The egg shape index was significantly higher in Oravka. Index of yolk and albumen was also significantly (P≤0.001 higher in Oravka. Haugh units score, that reflect the quality of the eggs, were found significantly (P≤0.001higher in Oravka too. On the other hand, yolk colour was detected significantly (P≤0.001 darker for the Czech Hen.

Mineral, amino acid, and hormonal composition of chicken eggshell powder and the evaluation of its use in human nutrition

NARCIS (Netherlands)

Schaafsma, A; Pakan, [No Value; Hofstede, GJH; Muskiet, FAJ; Van Der Veer, E; De Vries, PJF

2000-01-01

Chicken eggshell powder (ESP) might be an attractive source of Ca for human nutrition. To study its nutritional value, we analyzed minerals, amino acids, and hormones in commercially available Slovakian ESP. The mineral composition was compared with three Dutch ESP samples that differed in feed and

Histological Characteristics of Leg Muscles of 56-Day Old Pheasants Hatched from Eggs of Different Eggshell Colour

Directory of Open Access Journals (Sweden)

Dragan Zikic

2015-05-01

Full Text Available The aim of this paper was to examine the histological characteristics of leg muscles of pheasants hatched from eggs of a different colour. From muscle samples (M. biceps femoris of 56-day old pheasants hatched from eggs of different colour (dark brown, light brown, brown/green, blue/green histological preparations were made. Following parameters were examined: diameter of muscle cells, volume density of connective tissue in muscles, nucleo-cytoplasmatic ratio of muscle cells. Results showed that diameter of muscle cells was smaller in pheasants hatched from blue/green eggs compared to all other examinated groups. There was no differences in volume density of connective tissue in muscles between groups. Nucleo-cytoplasmatic ratio of muscle cells was higher in pheasants hatched from blue/green eggs compared to all other examinated groups. From obtained results it can be concluded that pheasants hatched from blue/green eggs had weaker muscle development than pheasants hatched from eggs of other eggshell colour. Cause of this could be related to structural differences of eggshells of various colour. This leads to weaker development of embryos and chicks hatched from blue/green eggs which reflects on differences in development of leg muscles.

Synthesis of Spongy-Like Mesoporous Hydroxyapatite from Raw Waste Eggshells for Enhanced Dissolution of Ibuprofen Loaded via Supercritical CO2

Directory of Open Access Journals (Sweden)

Abdul-Rauf Ibrahim

2015-04-01

Full Text Available The use of cheaper and recyclable biomaterials (like eggshells to synthesize high purity hydroxyapatite (HAp with better properties (small particle size, large surface area and pore volume for applications (in environmental remediation, bone augmentation and replacement, and drug delivery systems is vital since high-purity synthetic calcium sources are expensive. In this work, pure and mesoporous HAp nanopowder with large pore volume (1.4 cm3/g and surface area (284.1 m2/g was produced from raw eggshells at room temperature using a simple two-step procedure. The control of precursor droplets could stabilize the pH value of the reaction solution, because of the size of the needle (of the syringe pump used for precursor additions leading to production of HAp with high surface area and pore size. The as-produced HAp revealed high ibuprofen (as a model drug loading (1.38 g/g HAp, enhanced dissolution and controllable release of the drug via solute-saturated supercritical carbon dioxide.

Synthesis of Spongy-Like Mesoporous Hydroxyapatite from Raw Waste Eggshells for Enhanced Dissolution of Ibuprofen Loaded via Supercritical CO2

Science.gov (United States)

Ibrahim, Abdul-Rauf; Li, Xiangyun; Zhou, Yulan; Huang, Yan; Chen, Wenwen; Wang, Hongtao; Li, Jun

2015-01-01

The use of cheaper and recyclable biomaterials (like eggshells) to synthesize high purity hydroxyapatite (HAp) with better properties (small particle size, large surface area and pore volume) for applications (in environmental remediation, bone augmentation and replacement, and drug delivery systems) is vital since high-purity synthetic calcium sources are expensive. In this work, pure and mesoporous HAp nanopowder with large pore volume (1.4 cm3/g) and surface area (284.1 m2/g) was produced from raw eggshells at room temperature using a simple two-step procedure. The control of precursor droplets could stabilize the pH value of the reaction solution, because of the size of the needle (of the syringe pump used for precursor additions) leading to production of HAp with high surface area and pore size. The as-produced HAp revealed high ibuprofen (as a model drug) loading (1.38 g/g HAp), enhanced dissolution and controllable release of the drug via solute-saturated supercritical carbon dioxide. PMID:25860950

Thin and thick layers of resin-based sealer cement bonded to root dentine compared: Adhesive behaviour.

Science.gov (United States)

Pane, Epita S; Palamara, Joseph E A; Messer, Harold H

2015-12-01

This study aims to evaluate tensile and shear bond strengths of one epoxy (AH) and two methacrylate resin-based sealers (EZ and RS) in thin and thick layers bonded to root dentine. An alignment device was prepared for accurate positioning of 20 root dentine cylinders in a predefined gap of 0.1 or 1 mm. Sealer was placed in the interface. Bond strength tests were conducted. Mode of failures and representative surfaces were evaluated. Data were analysed using anova and post-hoc tests, with P thick layer of sealer produced higher bond strength, except for the shear bond strength of EZ. Significant differences between thin and thick layers were found only in tensile bond strengths of AH and RS. Mixed type of failure was constantly found with all sealers. Bond strengths of thick layers of resin-based sealers to root dentine tended to be higher than with thin layers. © 2015 Australian Society of Endodontology.

Hen's eggshell strength under impact loading

Czech Academy of Sciences Publication Activity Database

Nedomová, Š.; Trnka, Jan; Dvořáková, Pavla; Buchar, J.; Severa, L.

2009-01-01

Roč. 94, 3-4 (2009), s. 350-357 ISSN 0260-8774 R&D Projects: GA AV ČR IAA201990701 Institutional research plan: CEZ:AV0Z20760514 Keywords : numerical simulation * egg * bar impact Subject RIV: GM - Food Processing Impact factor: 2.313, year: 2009 http://apps.isiknowledge.com/full_record.do?product=UA&search_mode=GeneralSearch&qid=2&SID=Q14@FMepD39GcdkPk4D&page=1&doc=5&colname=WOS

Limestone and oyster shell for brown layers in their second egg production cycle

Directory of Open Access Journals (Sweden)

CC Pizzolante

2011-06-01

Full Text Available This study aimed at evaluating the effect of dietary calcium levels and the replacement of calcium sources with different particle size compositions on the performance and egg quality of brown layers in their second egg production cycle. A randomized block experimental design was applied with 12 treatments in a 3x4 factorial arrangement: three calcium levels (2.6, 3.2, 3.8 % and four combinations of calcium sources (1- 100% fine limestone (FL, 2- 50% FL + 50% coarse limestone (CL, 3- 50% FL and 50% oyster shell (OS, 4- 50% FL and 25% CL+ 25 %OS, with six replicates of eight birds each. Calcium sources were analyzed for geometric mean diameter (GMD and in-vitro solubility. The following performance and egg quality parameters were evaluated: egg weight (EW, g, egg production (% Eggs, egg mass (EM %, feed intake (FI g, feed conversion ratio (FCR kg/dz and FCR kg/kg, mortality (% Mort., specific egg gravity (SG, percentages of yolk (Y%, albumen (Alb% and eggshell (ES%, eggshell thickness (EST, eggshell breaking strength (BS, eggshell weight per surface area (EWSA, Haugh unit (HU, yolk index (YI and yolk color. Performance and internal egg quality were not affected by the treatments (p>0.05. Blocks had a significant effect on (p<0.05 FI and FCR (kg/dz and kg/kg. Treatments significantly influenced external egg quality, which improved as dietary calcium levels increases and when up to 50% fine limestone was replaced by combinations of coarse limestone with oyster shell.

Valorization of crude glycerol and eggshell biowaste as media components for hydrogen production: A scale-up study using co-culture system.

Science.gov (United States)

Pachapur, Vinayak Laxman; Das, Ratul Kumar; Brar, Satinder Kaur; Le Bihan, Yann; Buelna, Gerardo

2017-02-01

The properties of eggshells (EGS) as neutralizing and immobilizing agent were investigated for hydrogen (H 2 ) production using crude glycerol (CG) by co-culture system. Eggshells of different sizes and concentrations were used during batch and repeated-batch fermentation. For batch and repeated-batch fermentation, the maximum H 2 production (36.53±0.53 and 41.16±0.95mmol/L, respectively) was obtained with the EGS size of 33μmcomponents, the EGS concentration of 0.25% (w/v) was found to be optimum for maximum H 2 production (31.66±0.55mmol/L) and the production profile was comparable to H 2 production (32.07±0.92mmol/L) obtained with all media components. In scale-up study with semi-continuous bioreactor (7.5L), almost 1.5-fold increase (in comparison to mono-culture) i.e. 312.12mmol-H 2 /L-of medium with 86.65% glycerol utilization was obtained. Copyright © 2016 Elsevier Ltd. All rights reserved.

Gammatography of thick lead vessels

International Nuclear Information System (INIS)

Raghunath, V.M.; Bhatnagar, P.K.; Sundaram, V.M.

1979-01-01

Radiography, scintillation and GM counting and dose measurements using ionisation chamber equipment are commonly used for detecting flaws/voids in materials. The first method is mostly used for steel vessels and to a lesser extent thin lead vessels also and is essentially qualitative. Dose measuring techniques are used for very thick and large lead vessels for which high strength radioactive sources are required, with its inherent handling problems. For vessels of intermediate thicknesses, it is ideal to use a small strength source and a GM or scintillation counter assembly. At the Reactor Research Centre, Kalpakkam, such a system was used for checking three lead vessels of thicknesses varying from 38mm to 65mm. The tolerances specified were +- 4% variation in lead thickness. The measurements also revealed the non concentricity of one vessel which had a thickness varying from 38mm to 44mm. The second vessel was patently non-concentric and the dimensional variation was truly reproduced in the measurements. A third vessel was fabricated with careful control of dimensions and the measurements exhibited good concentricity. Small deviations were observed, attributable to imperfect bondings between steel and lead. This technique has the following advantages: (a) weaker sources used result in less handling problems reducing the personnel exposures considerably; (b) the sensitivity of the instrument is quite good because of better statistics; (c) the time required for scanning a small vessel is more, but a judicious use of a scintillometer for initial fast scan will help in reducing the total scanning time; (d) this method can take advantage of the dimensional variations themselves to get the calibration and to estimate the deviations from specified tolerances. (auth.)

Chemical synthesis of bone-like carbonate hydroxyapatite from hen eggshells and its characterization

Directory of Open Access Journals (Sweden)

Acevedo-Dávila, J. L.

2007-10-01

Full Text Available Carbonate hydroxyapatite (CHAp was synthesized from domestic hen eggshells by using three alternative wet chemical methods at room temperature. In the first method, the powdered eggshells were reacted directly with H3PO4. In the other two methods, calcium acetate was obtained in a first step by dissolving the eggshells in acetic acid. Then, calcium acetate was reacted with Na3PO4•12H2O and (NH42HPO4 in the second and third methods, respectively. The synthesized CHAp was characterized by X-Ray Diffraction (XRD, Fourier Transformed Infrared Spectroscopy (FT-IR, Scanning Electron Microscopy (SEM and Transmission Electron Microscopy (TEM. Fine and poorly crystallized CHAp was obtained under all experimental conditions employed. Among all synthesized materials, the one produced by the first method showed the closest resemblance to bovine bone, which was related to similar carbonate contents in both materials. In general, acicular CHAp crystals with a size ranging from 10 to 100 nm were obtained, which had an aspect ratio of ∼1/4. The morphology of the synthesized CHAp crystals was consistent with their estimated carbonate content.

Se sintetizó carbonato-hidroxiapatita (CHAp a partir de cascarón de huevo de gallina, usando tres métodos químicos alternativos vía húmeda a temperatura ambiente. En el primer método, el cascarón pulverizado fue hecho reaccionar directamente con H3PO4. En los otros dos métodos, el primer paso fue la obtención de acetato de calcio mediante la disolución del cascarón en ácido acético. Luego, el acetato de calcio fue hecho reaccionar con Na3PO4•12H2O y (NH42HPO4 en el segundo y tercer método, respectivamente. El CHAp sintetizado fue caracterizado por difracción de rayos X (DRX, espectroscopia infrarroja por transformada de Fourier (FT-IR, microscopía electrónica de barrido (MEB y microscopía electrónica de transmisión (MET. Bajo todas las condiciones experimentales empleadas se obtuvo CHAp

Effect of eggshell temperature and a hole in the air cell on the perinatal development and physiology of layer hatchlings

NARCIS (Netherlands)

Molenaar, R.; Vries, de S.; Anker, van den I.; Meijerhof, R.; Kemp, B.; Brand, van den H.

2010-01-01

To investigate the effect of incubation conditions on layer hatchlings, an experiment was performed in which layer eggs were incubated at a normal (37.8°C) or high (38.9°C) eggshell temperature (EST) and a hole was punctured in the air cell of half of the eggs in both EST treatments from d 14 of

Stable isotopes in emu and genyornis eggshell and changes in moisture source delivery to the Australian interior over the last 70 ka

International Nuclear Information System (INIS)

Johnson, B.J.; Miller, G.H.; Fogel, M.L.

1997-01-01

Moisture delivery to the northern and southern margins of the Australian continent is largely seasonal. Northern Australia receives almost all of its precipitation from the Australian monsoon in the summer months, and southern Australia receives most of its precipitation from the northward expansion fo the westerlies in the winter months. Central Australia is semi-arid to arid, and receives its moisture throughout the year, from convective disturbances arising from either the Australian monsoon or the Westerlies. Geologic evidence from central Australia indicates that the Lake Eyre Basin (LEB) has been both wetter and drier than it is today throughout the late Quaternary. Information on the nature of these climatic changes is derived from the stable isotope composition of late Quaternary fossil avian eggshell collected from the LEB. The eggshells analyzed were laid by two large flightless birds indigenous to Australia: the emu (extant) and Genyornis newtoni (extinct), and span the last 70 ka. (author)

Dynamics of lava flow - Thickness growth characteristics of steady two-dimensional flow

Science.gov (United States)

Park, S.; Iversen, J. D.

1984-01-01

The thickness growth characteristics of flowing lava are investigated using a heat balance model and a two-dimensional model for flow of a Bingham plastic fluid down an inclined plane. It is found that yield strength plays a crucial role in the thickening of a lava flow of given flow rate. To illustrate this point, downstream thickness profiles and yield strength distributions were calculated for flows with mass flow rates of 10,000 and 100,000 kg/m-sec. Higher flow rates led to slow cooling rates which resulted in slow rate of increase of yield strength and thus greater flow lengths.

Sensitivity study of buckling strength for cylindrical shells

Energy Technology Data Exchange (ETDEWEB)

Kato, Hideo; Sasaki, Toru [Institute of Nuclear Safety System Inc., Mihama, Fukui (Japan)

2001-09-01

Aiming at making clear buckling behavior of cylindrical shells under earthquake loadings, we investigated procedure of recent elastic-plastic buckling analysis by finite element method (FEM). Thereby it is confirmed that the buckling strength becomes as well as that of a shell with a cross section of a perfect cylinder, if we apply the first buckling eigenvector to imperfection mode and assume the maximum imperfection amplitude to be 1% of the wall thickness. And then, by carrying out sensitivity study of buckling with geometrical parameters, such as length (L), radius (R), wall thickness (t), and load parameter, such as pressure, we obtained several characteristics about buckling strength and buckling mode for cylindrical shells. From the geometrical parameter analysis, it is seen that bending buckling occurs for small R/t (thick wall) and elastic buckling occurs for 2{<=}L/R{<=}4 and R/t{>=}400. And from the load parameter analysis, it is shown that hoop stress caused by the inner pressure increases shear buckling strength but decreases bending buckling strength, and hoop stress by hydrostatic pressure changes buckling mode and generates local deformation. (author)

Effect of adhesive thickness on adhesively bonded T-joint

International Nuclear Information System (INIS)

Abdullah, A R; Afendi, Mohd; Majid, M S Abdul

2013-01-01

The aim of this work is to analyze the effect of adhesive thickness on tensile strength of adhesively bonded stainless steel T-joint. Specimens were made from SUS 304 Stainless Steel plate and SUS 304 Stainless Steel perforated plate. Four T-joint specimens with different adhesive thicknesses (0.5, 1.0, 1.5 and 2.0 mm) were made. Experiment result shows T-joint specimen with adhesive thickness of 1.0 mm yield highest maximum load. Identical T-joint specimen jointed by spot welding was also tested. Tensile test shows welded T-Joint had eight times higher tensile load than adhesively bonded T-joint. However, in low pressure application such as urea granulator chamber, high tensile strength is not mandatory. This work is useful for designer in fertilizer industry and others who are searching for alternative to spot welding

Why are birds' eggs colourful? Eggshell pigments co-vary with life-history and nesting ecology among British breeding non-passerine birds

Czech Academy of Sciences Publication Activity Database

Cassey, P.; Thomas, G.H.; Portugal, S. J.; Maurer, G.; Hauber, M. E.; Grim, T.; Lovell, P.G.; Mikšík, Ivan

2012-01-01

Roč. 106, č. 3 (2012), s. 657-672 ISSN 0024-4066 R&D Projects: GA ČR(CZ) GA203/08/1428 Institutional research plan: CEZ:AV0Z5011922 Institutional support: RVO:67985823 Keywords : biliverdin * protoporphyrin * eggshell pigment Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 2.413, year: 2012

Study of formation of green eggshell color in ducks through global gene expression.

Science.gov (United States)

Xu, Fa Qiong; Li, Ang; Lan, Jing Jing; Wang, Yue Ming; Yan, Mei Jiao; Lian, Sen Yang; Wu, Xu

2018-01-01

The green eggshell color produced by ducks is a threshold trait that can be influenced by various factors, such as hereditary, environment and nutrition. The aim of this study was to investigate the genetic regulation of the formation of eggs with green shells in Youxian ducks. We performed integrative analysis of mRNAs and miRNAs expression profiling in the shell gland samples from ducks by RNA-Seq. We found 124 differentially expressed genes that were associated with various pathways, such as the ATP-binding cassette (ABC) transporter and solute carrier supper family pathways. A total of 31 differentially expressed miRNAs were found between ducks laying green eggs and white eggs. KEGG pathway analysis of the predicted miRNA target genes also indicated the functional characteristics of these miRNAs; they were involved in the ABC transporter pathway and the solute carrier (SLC) supper family. Analysis with qRT-PCR was applied to validate the results of global gene expression, which showed a correlation between results obtained by RNA-seq and RT-qPCR. Moreover, a miRNA-mRNA interaction network was established using correlation analysis of differentially expressed mRNA and miRNA. Compared to ducks that lay white eggs, ducks that lay green eggs include six up-regulated miRNAs that had regulatory effects on 35 down-regulated genes, and seven down-regulated miRNAs which influenced 46 up-regulated genes. For example, the ABC transporter pathway could be regulated by expressing gga-miR-144-3p (up-regulated) with ABCG2 (up-regulated) and other miRNAs and genes. This study provides valuable information about mRNA and miRNA regulation in duck shell gland tissues, and provides foundational information for further study on the eggshell color formation and marker-assisted selection for Youxian duck breeding.

Study of formation of green eggshell color in ducks through global gene expression.

Directory of Open Access Journals (Sweden)

Fa Qiong Xu

Full Text Available The green eggshell color produced by ducks is a threshold trait that can be influenced by various factors, such as hereditary, environment and nutrition. The aim of this study was to investigate the genetic regulation of the formation of eggs with green shells in Youxian ducks. We performed integrative analysis of mRNAs and miRNAs expression profiling in the shell gland samples from ducks by RNA-Seq. We found 124 differentially expressed genes that were associated with various pathways, such as the ATP-binding cassette (ABC transporter and solute carrier supper family pathways. A total of 31 differentially expressed miRNAs were found between ducks laying green eggs and white eggs. KEGG pathway analysis of the predicted miRNA target genes also indicated the functional characteristics of these miRNAs; they were involved in the ABC transporter pathway and the solute carrier (SLC supper family. Analysis with qRT-PCR was applied to validate the results of global gene expression, which showed a correlation between results obtained by RNA-seq and RT-qPCR. Moreover, a miRNA-mRNA interaction network was established using correlation analysis of differentially expressed mRNA and miRNA. Compared to ducks that lay white eggs, ducks that lay green eggs include six up-regulated miRNAs that had regulatory effects on 35 down-regulated genes, and seven down-regulated miRNAs which influenced 46 up-regulated genes. For example, the ABC transporter pathway could be regulated by expressing gga-miR-144-3p (up-regulated with ABCG2 (up-regulated and other miRNAs and genes. This study provides valuable information about mRNA and miRNA regulation in duck shell gland tissues, and provides foundational information for further study on the eggshell color formation and marker-assisted selection for Youxian duck breeding.

DECO FRECASE (drywall eco-friendly from eggshell and cane bagasse) as an innovation of eco-friendly interior construction

Science.gov (United States)

Imron, M. A.; Ahkam, D. N. I.; Hidayat, A. W.

2017-12-01

The number of factories and home industries, both upper and lower middle class certainly adds waste generated, resulting in environmental pollution. The development of buildings is one of the largest contributors to global warming. For that, it takes technological innovations that lead to the criteria of green building. The application of green material is important aspects of environmentally friendly development, the selection of materials on the green material criteria of both roles should be applied continuously in order to realize the environmental sustainability of the material. Utilization Waste eggshell and bagasse which is a community waste, has the potential to become innovative environmentally friendly building materials. The eggshell is composed of 94% calcium carbonate, 1% magnesium carbonate, 1% calcium phosphate, and 4% organic material, especially protein, while the bagasse has a high content of silica (SiO2). In this study, the compounds are used as raw material for making alternative drywall in the form of DECO FRECASE. DECO FRECASE is an innovation of environmentally friendly building materials as an interior wall construction. Through DECO FRECASE, it is expected that building material innovation in Indonesia can be improved and of course environmental problems can be minimized by utilizing it as raw material for building construction.

Effect of vitamin K on bone integrity and eggshell quality of white hen at the final phase of the laying cycle Efeito da vitamina K sobre a integridade óssea e da casca de ovos de poedeiras leves na fase final de postura

Directory of Open Access Journals (Sweden)

Jovanir Inês Müller Fernandes

2009-03-01

Full Text Available The effect of four levels of dietary vitamin K (vit. K on production, egg quality and bone structure of laying hens near the end of the production cycle were studied. A total of 192 Hy-Line, W-36 hens, 67 weeks of age, were distributed into a completely randomized design with four treatments (0, 2, 8, 32 mg vit. K/kg of diet, six replicates and eight birds per experimental unit. Corn-soybean-meal basal diets were isonitrogenous (15.5% crude protein, isoenergetic (2,790 kcal ME/kg, isocalcium (4.25% Ca and isophosphorus (0.40% available P. Vitamin K supplementation did not alter egg mass, feed intake, feed conversion (kg/kg, bone breaking strength, specific egg gravity, eggshell weight, thickness and percentage of thin and cracked shell. A linear effect on egg weight, laying percent, and feed conversion (kg/dozen was observed, as well as a quadratic effect on the ash bone content. In conclusion, the inclusion of increasing levels of vitamin K to the diet influenced performance and bone mineralization, but not eggshell quality. The lack of consistency in the efficiency of supplemental vitamin K on eggshell quality may be due to the age of hens.Objetivou-se com este estudo avaliar o efeito de quatro níveis dietéticos de vitamina K (vit. K sobre o desempenho e a qualidade de ovos e ossos de poedeiras leves na fase final de postura. Foram utilizadas 192 poedeiras comerciais com 67 semanas de idade, distribuídas em delineamento casualizado, com quatro níveis de vitamina K (0, 2, 8, 32 mg/kg, seis repetições e oito aves por unidade experimental. As rações eram isoprotéicas (15,5% de proteína bruta, isoenergéticas (2.790 kcal de energia metabolizável/kg, isocálcicas (4,25% cálcio e isofosfóricas (0,40% fósforo disponível e foram formuladas à base de milho e farelo de soja. A suplementação de vitamina K não alterou a massa de ovos, o consumo de ração, a conversão alimentar (kg/kg, a resistência óssea a quebra, a gravidade espec

Ultrasound-assisted synthesis of curcumin analogs promoted by activated chicken eggshells

Science.gov (United States)

Mardiana, L.; Ardiansah, B.; Septiarti, A.; Bakri, R.; Kosamagi, G.

2017-07-01

Curcumin has been widely known as a multifunctional natural product which has many biological activities. However, the biggest limitation for the large scale application of curcumin is its poor bioavailability. This research presented a cheap, mild and efficient solvent-free synthesis of monocarbonyl analogs of curcumin via Aldol condensation using activated chicken eggshells (ACE). Dibenzalpropanone as a product of Aldol condensation was prepared by mixing benzaldehyde and acetone using a simple glass tube in the presence of ACE under ultrasound irradiation (78 % yield), while dibenzalcyclohexanone was produced from the reaction of benzaldehyde with cyclohenxanone (81 %). The products have been characterized by FTIR, UV-Vis spectrophotometer and GC-MS instruments. The FTIR spectra show a significant absorption of carbonyl group that attached to the double bond in α,β-position at 1630-1660 cm-1. The molecular cation of m/z of 234 and 274 is in agreement with the products structures.

Effects of core-to-dentin thickness ratio on the biaxial flexural strength, reliability, and fracture mode of bilayered materials of zirconia core (Y-TZP) and veneer indirect composite resins.

Science.gov (United States)

Su, Naichuan; Liao, Yunmao; Zhang, Hai; Yue, Li; Lu, Xiaowen; Shen, Jiefei; Wang, Hang

2017-01-01

Indirect composite resins (ICR) are promising alternatives as veneering materials for zirconia frameworks. The effects of core-to-dentin thickness ratio (C/Dtr) on the mechanical property of bilayered veneer ICR/yttria-tetragonal zirconia polycrystalline (Y-TZP) core disks have not been previously studied. The purpose of this in vitro study was to assess the effects of C/Dtr on the biaxial flexural strength, reliability, and fracture mode of bilayered veneer ICR/ Y-TZP core disks. A total of 180 bilayered 0.6-mm-thick composite resin disks in core material and C/Dtr of 2:1, 1:1, and 1:2 were tested with either core material placed up or placed down for piston-on-3-ball biaxial flexural strength. The mean biaxial flexural strength, Weibull modulus, and fracture mode were measured to evaluate the variation trend of the biaxial flexural strength, reliability, and fracture mode of the bilayered disks with various C/Dtr. One-way analysis of variance (ANOVA) and chi-square tests were used to evaluate the variation tendency of fracture mode with the C/Dtr or material placed down during testing (α=.05). Light microscopy was used to identify the fracture mode. The mean biaxial flexural strength and reliability improved with the increase in C/Dtr when specimens were tested with the core material either up and down, and depended on the materials that were placed down during testing. The rates of delamination, Hertzian cone cracks, subcritical radial cracks, and number of fracture fragments partially depended on the C/Dtr and the materials that were placed down during testing. The biaxial flexural strength, reliability, and fracture mode in bilayered structures of Y-TZP core and veneer ICR depend on both the C/Dtr and the material that was placed down during testing. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Textural improvement of salt-reduced Alaska pollack (Theragra chalcogramma) roe product by CaCl2.

Science.gov (United States)

Chen, Chaoping; Okazaki, Emiko; Osako, Kazufumi

2016-12-15

Salt-reduced Alaska pollack roe benefits public health by decreasing NaCl intake; however, it has a poor texture with low breaking strength. This study addresses the feasibility of NaCl reduction in salted roe products, with focusing on the improvement of breaking strength using CaCl2. Salted roe products were prepared by immersing Alaska pollack roe in either NaCl solutions (3.5, 7.0, 15.0, 20.0, and 25.0%) or 7.0% NaCl solutions with added CaCl2 (0.0, 0.5, 1.0, 2.0, and 3.0%). Breaking strength, moisture and salt contents, eggshell protein composition of the salted roe products, as well as total endogenous transglutaminase (TGase) activity in various NaCl and CaCl2 concentrations were analyzed. CaCl2 addition enhanced eggshell protein crosslinking and breaking strength of the salt-reduced roe products. An acyl transfer reaction catalyzed by calcium-dependent TGase may be responsible for the eggshell protein crosslinking and improved texture. Thus, we successfully developed a salt-reduced Alaska roe product using CaCl2. Copyright © 2016 Elsevier Ltd. All rights reserved.

Thermodynamic Alloy Design of High Strength and Toughness in 300 mm Thick Pressure Vessel Wall of 1.25Cr-0.5Mo Steel

Directory of Open Access Journals (Sweden)

Hye-sung Na

2018-01-01

Full Text Available In the 21st century, there is an increasing need for high-capacity, high-efficiency, and environmentally friendly power generation systems. The environmentally friendly integrated gasification combined-cycle (IGCC technology has received particular attention. IGCC pressure vessels require a high-temperature strength and creep strength exceeding those of existing pressure vessels because the operating temperature of the reactor is increased for improved capacity and efficiency. Therefore, high-pressure vessels with thicker walls than those in existing pressure vessels (≤200 mm must be designed. The primary focus of this research is the development of an IGCC pressure vessel with a fully bainitic structure in the middle portion of the 300 mm thick Cr-Mo steel walls. For this purpose, the effects of the alloy content and cooling rates on the ferrite precipitation and phase transformation behaviors were investigated using JMatPro modeling and thermodynamic calculation; the results were then optimized. Candidate alloys from the simulated results were tested experimentally.

Behaviour and strength assessment of masonry prisms

Directory of Open Access Journals (Sweden)

Nassif Nazeer Thaickavil

2018-06-01

Full Text Available This is a case study presenting the cracking behavior and assessment of the compressive strength of masonry prisms. The compressive strength of masonry was determined by performing laboratory tests on 192 masonry prism specimens corresponding to 3 specimens each in 64 groups. The variables considered in the experimental program are type of brick, strength of masonry and height-to-thickness (h/t ratio of the prism specimen. Pressed earth bricks and burnt clay bricks were used for the preparation of masonry prisms. A mathematical model is also proposed for the estimation of compressive strength of masonry prisms by performing a statistical multiple regression analysis on 232 data sets, which includes 64 test data from the present study and 168 test data published in the literature. The model was developed based on the regression analysis of test data of prisms made of a variety of masonry units namely clay bricks, pressed earth bricks, concrete blocks, calcium silicate bricks, stone blocks, perforated bricks and soft mud bricks. The proposed model not only accounts for the wide ranges of compressive strengths of masonry unit and mortar, but also accounts for the influence of volume fractions of masonry unit and mortar in addition to the height-to-thickness ratio. The predicted compressive strength of prisms using the proposed model is compared with 14 models available in published literature. The predicted strength was found to be in good agreement with the corresponding experimental data. Keywords: Prism strength, Stack bonded masonry, Running bonded masonry, Masonry unit strength, Cracking

Resección de hemivértebra con técnica de eggshell en cifoescoliosis congénita: resultados en niños entre uno y siete años Ressecção de hemivertébra com a técnica de eggshell em cifoescoliose congênita: resultados em crianças com idade entre um e sete anos Hemivertebrae resection with eggshell procedure for congenital kyphoscoliosis: results in children aged from one to seven years

Directory of Open Access Journals (Sweden)

Gonzalo Arriagada Ocampo

2009-09-01

Full Text Available INTRODUCCIÓN: La hemivértebra es la causa de 50% de las cifoescoliosis congénitas y en general requiere tratamiento quirúrgico. OBJETIVO: evaluar los resultados clínicos y radiológicos de la resección de hemivértebra con técnica de eggshell en niños entre uno y siete años. DISEÑO DEL ESTUDIO: análisis retrospectivo de pacientes sometidos a resección de hemivértebra con técnica de eggshell. MÉTODOS: entre Enero del 2006 y Junio del 2008, siete hemivértebras fueron resecadas en siete pacientes consecutivos, entre uno y siete años de edad. Se revisó retrospectivamente las fichas clínicas y radiografías. La edad promedio al momento de la cirugía fue 3,2 años (rango de uno a siete años y el seguimiento promedio fue de 17 meses (rango 7 a 35 meses. Se registró ángulo de Cobb de la escoliosis y cifosis en el preoperatorio y al término del seguimiento, tiempo operatorio, transfusión de glóbulos rojos y complicaciones. RESULTADOS: el ángulo preoperatorio promedio de la escoliosis fue 35° y 19° al término del seguimiento, con un 40% de corrección. El ángulo preoperatorio promedio de la cifosis fue 42° y 25° al término del seguimiento, con un 33% de corrección. Cuatro pacientes necesitaron transfusión de glóbulos rojos, promedio 1,25 unidades. El tiempo quirúrgico promedio fue 225 minutos. Dos pacientes presentaron complicaciones, una rotura dural y una fractura pedicular. No se presentaron complicaciones neurológicas. Todos los pacientes presentaban fusión sólida al término del seguimiento. CONCLUSIÓN: la resección de hemivértebra con técnica de eggshell es un procedimiento seguro, que permite una excelente e inmediata corrección de la cifoescoliosis congénita, la que se mantiene en el corto plazo.INTRODUÇÃO: A hemivértebra associa-se a 50% das cifoescolioses congênitas e geralmente requer tratamento cirúrgico. OBJETIVO: avaliar os resultados clínicos e radiológicos da ressecção da hemiv

Speckled eggs: water-loss and incubation behaviour in the great tit Parus major.

Science.gov (United States)

Higham, James P; Gosler, Andrew G

2006-10-01

Many small passerine birds worldwide lay white eggs speckled with red, brown and black protoporphyrin pigment spots (maculation). Unlike some patterns of avian eggshell pigmentation which clearly serve a crypsis or signalling function, the ubiquity of maculation among passerines suggests that its origins lie in another function, not specific to any particular ecological or behavioural group. Elsewhere, we have presented evidence that protoporphyrin pigments serve a structural function related to eggshell thickness and calcium availability: eggshell maculation in the great tit Parus major increases with decreasing soil calcium levels, pigments demarcate thinner areas of shell, and both the pigment intensity and distribution are related to shell thickness. Here we show that maculation also affects the rate of water loss from the egg during incubation (approximately Mass Loss per Day or MLD, which is critical to egg viability), but not that of unincubated eggs. We also demonstrate, both by observation and experiment, that the effect of female incubation behaviour on MLD compensates in some way for variation in egg characteristics, and that differences between females in the degree of such compensation are related to differences in clutch maculation. Our results suggest that, while a principal function of maculation in this species may be to strengthen the eggshell, it may also reduce eggshell permeability when large amounts of pigment are used, and that this necessitates a behavioural adjustment from the female during incubation. We discuss these findings and make further testable predictions from our model.

Effect of Some Egg Quality Traits on Hatching Results in Brown Pure Lines

Directory of Open Access Journals (Sweden)

İsmail Durmuş

2016-09-01

Full Text Available This study was conducted to determine the influence of eggshell thickness, albumen height, yolk height and haugh unit on hatching results. A total of 746 eggs, which were obtained and evaluated for egg quality parameters from 100 brown pure line hens of 42 weeks of age, were used. Eggs were collected from each hen for 12 days and individual incubation was carried out. Eggs were grouped based on quality parameters and evaluated accordingly. The findings suggested that hatchability, hatchability of fertile eggs, early, mid and late embryonic mortality did not differ in terms of haugh unit, albumen height, eggshell thickness and yolk height groups. However, early embryonic mortality was found different between the yolk height groups. No relationship was determined among albumen height, haugh unit, eggshell thickness and hatching results. There was no relation between yolk height and hatchability of fertile eggs, hatchability, mid and late embryonic mortalities but was a positive correlation with early embryonic mortality. The results of the present study demonstrate that egg quality parameters studied here had no influence on hatching results except that early embryonic mortality increased with the yolk height.

Technical Note: Cortical thickness and density estimation from clinical CT using a prior thickness-density relationship

Energy Technology Data Exchange (ETDEWEB)

Humbert, Ludovic, E-mail: ludohumberto@gmail.com [Galgo Medical, Barcelona 08036 (Spain); Hazrati Marangalou, Javad; Rietbergen, Bert van [Orthopaedic Biomechanics, Department of Biomedical Engineering, Eindhoven University of Technology, Eindhoven 5600 MB (Netherlands); Río Barquero, Luis Miguel del [CETIR Centre Medic, Barcelona 08029 (Spain); Lenthe, G. Harry van [Biomechanics Section, KU Leuven–University of Leuven, Leuven 3001 (Belgium)

2016-04-15

Purpose: Cortical thickness and density are critical components in determining the strength of bony structures. Computed tomography (CT) is one possible modality for analyzing the cortex in 3D. In this paper, a model-based approach for measuring the cortical bone thickness and density from clinical CT images is proposed. Methods: Density variations across the cortex were modeled as a function of the cortical thickness and density, location of the cortex, density of surrounding tissues, and imaging blur. High resolution micro-CT data of cadaver proximal femurs were analyzed to determine a relationship between cortical thickness and density. This thickness-density relationship was used as prior information to be incorporated in the model to obtain accurate measurements of cortical thickness and density from clinical CT volumes. The method was validated using micro-CT scans of 23 cadaver proximal femurs. Simulated clinical CT images with different voxel sizes were generated from the micro-CT data. Cortical thickness and density were estimated from the simulated images using the proposed method and compared with measurements obtained using the micro-CT images to evaluate the effect of voxel size on the accuracy of the method. Then, 19 of the 23 specimens were imaged using a clinical CT scanner. Cortical thickness and density were estimated from the clinical CT images using the proposed method and compared with the micro-CT measurements. Finally, a case-control study including 20 patients with osteoporosis and 20 age-matched controls with normal bone density was performed to evaluate the proposed method in a clinical context. Results: Cortical thickness (density) estimation errors were 0.07 ± 0.19 mm (−18 ± 92 mg/cm{sup 3}) using the simulated clinical CT volumes with the smallest voxel size (0.33 × 0.33 × 0.5 mm{sup 3}), and 0.10 ± 0.24 mm (−10 ± 115 mg/cm{sup 3}) using the volumes with the largest voxel size (1.0 × 1.0 × 3.0 mm{sup 3}). A trend for the

Technical Note: Cortical thickness and density estimation from clinical CT using a prior thickness-density relationship

International Nuclear Information System (INIS)

Humbert, Ludovic; Hazrati Marangalou, Javad; Rietbergen, Bert van; Río Barquero, Luis Miguel del; Lenthe, G. Harry van

2016-01-01

Purpose: Cortical thickness and density are critical components in determining the strength of bony structures. Computed tomography (CT) is one possible modality for analyzing the cortex in 3D. In this paper, a model-based approach for measuring the cortical bone thickness and density from clinical CT images is proposed. Methods: Density variations across the cortex were modeled as a function of the cortical thickness and density, location of the cortex, density of surrounding tissues, and imaging blur. High resolution micro-CT data of cadaver proximal femurs were analyzed to determine a relationship between cortical thickness and density. This thickness-density relationship was used as prior information to be incorporated in the model to obtain accurate measurements of cortical thickness and density from clinical CT volumes. The method was validated using micro-CT scans of 23 cadaver proximal femurs. Simulated clinical CT images with different voxel sizes were generated from the micro-CT data. Cortical thickness and density were estimated from the simulated images using the proposed method and compared with measurements obtained using the micro-CT images to evaluate the effect of voxel size on the accuracy of the method. Then, 19 of the 23 specimens were imaged using a clinical CT scanner. Cortical thickness and density were estimated from the clinical CT images using the proposed method and compared with the micro-CT measurements. Finally, a case-control study including 20 patients with osteoporosis and 20 age-matched controls with normal bone density was performed to evaluate the proposed method in a clinical context. Results: Cortical thickness (density) estimation errors were 0.07 ± 0.19 mm (−18 ± 92 mg/cm"3) using the simulated clinical CT volumes with the smallest voxel size (0.33 × 0.33 × 0.5 mm"3), and 0.10 ± 0.24 mm (−10 ± 115 mg/cm"3) using the volumes with the largest voxel size (1.0 × 1.0 × 3.0 mm"3). A trend for the cortical thickness and

Study on the Joining Strength of Spot Welding using POMISPOT Device

International Nuclear Information System (INIS)

Mohd Azhar Ahmad; Siti Aiasah Hashim; Mohd Rizal Chulan

2015-01-01

Welding is a process to join metals. Spot welding is commonly used for specific purposes such joining in small areas or making temporary joints. POMISPOT is a spot welder that was designed and built by the ADC group, using capacitive resistance method. This study was made to obtain the welding strength that can be made by this spot welder. The study used stainless steel pieces of different thickness and by varying the applied voltage. The strength of welded pieces is tested by applying loads. The relationship between the thickness, voltage and welding strength will be used as the basis of specifications of this tool. (author)

Pressure vessels fabricated with high-strength wire and electroformed nickel

Science.gov (United States)

Roth, B.

1966-01-01

Metal pressure vessels of various shapes having high strength-to-weight ratios are fabricated by using known techniques of filament winding and electroforming. This eliminates nonuniform wall thickness and unequal wall strength which resulted from welding formed vessel segments together.

Nutritional Supplement of Hatchery Eggshell Membrane Improves Poultry Performance and Provides Resistance against Endotoxin Stress.

Science.gov (United States)

Makkar, S K; Rath, N C; Packialakshmi, B; Zhou, Z Y; Huff, G R; Donoghue, A M

2016-01-01

Eggshells are significant part of hatchery waste which consist of calcium carbonate crust, membranes, and proteins and peptides of embryonic origins along with other entrapped contaminants including microbes. We hypothesized that using this product as a nutritional additive in poultry diet may confer better immunity to the chickens in the paradigm of mammalian milk that enhances immunity. Therefore, we investigated the effect of hatchery eggshell membranes (HESM) as a short term feed supplement on growth performance and immunity of chickens under bacterial lipopolysaccharide (LPS) challenged condition. Three studies were conducted to find the effect of HESM supplement on post hatch chickens. In the first study, the chickens were fed either a control diet or diets containing 0.5% whey protein or HESM as supplement and evaluated at 5 weeks of age using growth, hematology, clinical chemistry, plasma immunoglobulins, and corticosterone as variables. The second and third studies were done to compare the effects of LPS on control and HESM fed birds at 5 weeks of age following at 4 and 24 h of treatment where the HESM was also sterilized with ethanol to deplete bacterial factors. HESM supplement caused weight gain in 2 experiments and decreased blood corticosterone concentrations. While LPS caused a significant loss in body weight at 24 h following its administration, the HESM supplemented birds showed significantly less body weight loss compared with the control fed birds. The WBC, heterophil/lymphocyte ratio, and the levels of IgG were low in chickens fed diets with HESM supplement compared with control diet group. LPS challenge increased the expression of pro-inflammatory cytokine gene IL-6 but the HESM fed birds showed its effect curtailed, also, which also, favored the up-regulation of anti-inflammatory genes compared with control diet fed chickens. Post hatch supplementation of HESM appears to improve performance, modulate immunity, and increase resistance of

effects of temperature levels and concrete cover thickness

African Journals Online (AJOL)

HP USER

With the knowledge of the temperature of the fire, thickness of concrete cover, residual strength of ... the structural behavior during fires by a careful inspection of the ... visual or physical damage is negligible; and Alonso[9] in the same vein said ...

Fatigue strength of socket welded pipe joint

International Nuclear Information System (INIS)

Iida, K.; Matsuda, F.; Sato, M.; Higuchi, M.; Nakagawa, A.

1994-01-01

Fully reversed four point bending fatigue tests were carried out of small diameter socket welded joints made of carbon steels. Experimental parameters are pipe diameter, thickness of pipe and socket wall, throat depth and shape of fillet welds, slip-on and diametral gaps in the socket welding, lack of penetration at the root of fillet welds, and peening of fillet welds. In most cases a fatigue crack started from the root of the fillet, but in the case of higher stress amplitude, it tended to start from the toe of fillet. The standard socket welded joint of 50 mm diameter showed relatively low fatigue strength, 46 MPa in stress amplitude at the 10 7 cycles failure life. This value corresponds to about 1/5 of that of the smoothed base metal specimens in axial fatigue. The fatigue strength showed decrease with increasing pipe diameter, and increase with increasing the thickness of pipe and socket wall. The effects of throat depth and shape of fillet welds on fatigue strength were not significant. Contrary to the expectation, the fatigue strength of the socket welded joint without slip-on gap is higher than that of the joint with the normal gap. A lack of penetration at the root deleteriously reduced fatigue strength, showing 14 MPa in stress amplitude at the 10 7 cycles failure life for the 50 mm diameter socket joint. (orig.)

Strength Gain Properties up to five-year age of high-strength mass concrete

International Nuclear Information System (INIS)

Mitarai, Y.; Shigenobu, M.; Hiramine, T.; Inoue, K.; Nakane, S.; Ohike, T.

1991-01-01

Genkai No.3 plant of Kyushu Electric Power Co., Inc. presently under construction is a PWR type nuclear power plant with 1180 MW power output, and a prestressed concrete containment vessel (PCCV) was adopted for the reactor. The concrete used for the construction of the PCCV is the mass concrete with the wall thickness of 1.3 m in the general parts of the cylinder, and about 2 m at buttresses. It is the high strength concrete of the specified strength 420 kgf/cm 2 . As the preliminary study for the construction using such high strength mass concrete, the examination was carried out on the strength gain property of structural concrete using full scale simulated members. The various problems in the quality control were contemplated based on the results of the examination, and were reflected to actual construction, designating 13 weeks as the age for strength control, in order to build the concrete structures with high reliability. In this report, the outline of the study on the strength gain up to 5 year age carried out in the preliminary study is discussed. The experimental method, the method of evaluating structural strength, the mixing proportion of concrete and the results are reported. (K.I.)

Investigation of thick grid plasma switches for thermionic system output voltage

International Nuclear Information System (INIS)

Alekseev, N.I.; Kaplan, V.B.; Martsinovski, A.M.

1992-01-01

Plasma switches (Cs and Cs-Ba tacitrons PS) with thick grid have grid with thickness more than mesh aperture size. These grids have some advantages as compared with small-scale/1.2/ones. For instance, much more electrical strength. This paper contains the thick-grid investigation results: the grid controls efficiency, the plasma parameters, probe researches of these parameters at conductive state and their variety during the process of quenching. The results showed the thick-grid PS plasma differed from the thin-grid PS significantly at the stationary state as well as by quenching dynamic features

Deformation Characteristics of Ultrahigh-Strength Concrete under Unrestrained and Restrained States

Directory of Open Access Journals (Sweden)

Joo-Ha Lee

2017-01-01

Full Text Available As structures like skyscrapers and long-span bridges become larger, the demand for higher strength of concrete is increasing. However, research on ultrahigh-strength concrete (UHSC is still in its infancy. In particular, UHSC is known to have a considerably higher level of autogenous shrinkage than normal strength concrete (NSC, and the possibility of cracking at an early age is very high. Therefore, in this study, shrinkage and cracking behavior of high-strength concrete (HSC, very-high-strength concrete (VHSC, and UHSC were evaluated through unrestrained shrinkage test and restrained shrinkage test (ring test. The primary experimental variables are the compressive strength level according to the water-to-binder ratio (W/B, fly ash content, and concrete specimen thickness. The experimental results demonstrated that the drying shrinkage decreased as the W/B ratio and the fly ash replacement ratio increased, and the restraint cracks appeared to be the earliest and most brittle in the UHSC with the smallest W/B. Increased concrete thickness and incorporation of fly ash were observed to inhibit crack initiation effectively.

Study on strength of thick reinforced concrete slab with opening - Part 2: Evaluation of the test results

International Nuclear Information System (INIS)

Hirai, T.; Itoh, M.; Takei, K.; Kanazu, T.; Abe, Y.; Takahashi, T.; Hayashi, N.; Sasaki, N.

1993-01-01

In comparing the strength of the partial models obtained from the test and the strength calculated by the various formulas for short span cantilevers based on recent research, it was found that the strength of the partial models coincided well with the calculated bending strength. It was confirmed that bending failure also preceded in the overall model from the tests. However various strengths such as the cracking strength and the yielding strength of rebars were larger, and displacements and strains in various parts were smaller than those in the partial models. It was attributed to the effects of circumferential distribution of the load. A convenient method was proposed for evaluation of the strength of the overall model. In this method, the overall model is divided into corbels, and the strength of the model is calculated as the sum of these corbels' strength. This method estimated the strength conveniently and conservatively. (author)

Effects of breeding habitat (woodland versus urban) and metal pollution on the egg characteristics of great tits (Parus major).

Science.gov (United States)

Hargitai, Rita; Nagy, Gergely; Nyiri, Zoltán; Bervoets, Lieven; Eke, Zsuzsanna; Eens, Marcel; Török, János

2016-02-15

In an urban environment, birds are exposed to metals, which may accumulate in their tissues and cause oxidative stress. Female birds may eliminate these pollutants through depositing them into eggs, thus eggs become suitable bioindicators of pollution. In this study, we aimed to analyse whether eggshell spotting pattern, egg volume, eggshell thickness and egg yolk antioxidant (lutein, tocopherol, retinol and selenium) levels were related to the breeding area (woodland versus urban) and the metal levels in the eggshell of a small passerine species, the great tit (Parus major). In the urban habitat, soil and eggshells contained higher concentrations of metals, and soil calcium level was also higher than that in the woodland. Eggshell spotting intensity and egg volume did not differ between eggs laid in the woodland and the urban park, and these traits were not related to the metal levels of the eggshell, suggesting that these egg characteristics are not sensitive indicators of metal pollution. A more aggregated eggshell spotting distribution indicated a higher Cu concentration of the eggshell. We found that eggshells were thinner in the less polluted woodland habitat, which is likely due to the limited Ca availability of the woodland area. Great tit eggs laid in the urban environment had lower yolk lutein, retinol and selenium concentrations, however, as a possible compensation for these lower antioxidant levels, urban females deposited more tocopherol into the egg yolk. It appears that females from different breeding habitats may provide similar antioxidant protection for their offspring against oxidative damage by depositing different specific dietary antioxidants. Egg yolk lutein and retinol levels showed a negative relationship with lead concentration of the eggshell, which may suggest that lead had a negative impact on the amount of antioxidants available for embryos during development in great tits. Copyright © 2015 Elsevier B.V. All rights reserved.

Influence of manufacturing parameters on the strength of PLA parts using Layered Manufacturing technique: A statistical approach

Science.gov (United States)

Jaya Christiyan, K. G.; Chandrasekhar, U.; Mathivanan, N. Rajesh; Venkateswarlu, K.

2018-02-01

A 3D printing was successfully used to fabricate samples of Polylactic Acid (PLA). Processing parameters such as Lay-up speed, Lay-up thickness, and printing nozzle were varied. All samples were tested for flexural strength using three point load test. A statistical mathematical model was developed to correlate the processing parameters with flexural strength. The result clearly demonstrated that the lay-up thickness and nozzle diameter influenced flexural strength significantly, whereas lay-up speed hardly influenced the flexural strength.

Influence of initial imperfections on ultimate strength of spherical shells

Directory of Open Access Journals (Sweden)

Chang-Li Yu

2017-09-01

Full Text Available Comprehensive consideration regarding influence mechanisms of initial imperfections on ultimate strength of spherical shells is taken to satisfy requirement of deep-sea structural design. The feasibility of innovative numerical procedure that combines welding simulation and non-linear buckling analysis is verified by a good agreement to experimental and theoretical results. Spherical shells with a series of wall thicknesses to radius ratios are studied. Residual stress and deformations from welding process are investigated separately. Variant influence mechanisms are discovered. Residual stress is demonstrated to be influential to stress field and buckling behavior but not to the ultimate strength. Deformations are proved to have a significant impact on ultimate strength. When central angles are less than critical value, concave magnitudes reduce ultimate strengths linearly. However, deformations with central angles above critical value are of much greater harm. Less imperfection susceptibility is found in spherical shells with larger wall thicknesses to radius ratios.

Maintained ship hull girder ultimate strength reliability considering corrosion and fatigue

DEFF Research Database (Denmark)

Hu, Yong; Cui, W.; Pedersen, Preben Terndrup

2004-01-01

The prupose of this paper is to propose a methodology to assess the time-variant ultimate strength of ship hull girder under the degradations of corrosion and fatigue. The effects of fatigue cracks on the tensile and compressive residual ultimate strength of stiffened panels and unstiffened plates......, webs and flanges, respectively. The effects of inspections and repair are taken into account. A minimum net thickness rule is used to determine repair policies. A procedure is proposed to determine the maximum allowable corrosion thickness of different parts of the hull cross section. The procedure...

Load bearing capacity of welded joints between dissimilar pipelines with unequal wall thickness

Energy Technology Data Exchange (ETDEWEB)

Beak, Jonghyun; Kim, Youngpyo; Kim, Woosik [Korea Gas Corporation, Suwon (Korea, Republic of)

2012-09-15

The behavior of the load bearing capacity of a pipeline with unequal wall thickness was evaluated using finite element analyses. Pipelines with a wall thickness ratio of 1.22-1.89 were adopted to investigate plastic collapse under tensile, internal pressure, or bending stress. A parametric study showed that the tensile strength and moment of a pipeline with a wall thickness ratio less than 1.5 were not influenced by the wall thickness ratio and taper angle; however, those of a pipeline with a wall thickness ratio more than 1.5 decreased considerably at a low taper angle. The failure pressure of a pipeline with unequal wall thickness was not influenced by the wall thickness ratio and taper angle.

Relationships between bone strength and bone quality. Three-dimensional imaging analysis in ovariectomized mice

International Nuclear Information System (INIS)

Wakabayashi, Suguru; Sakurai, Takashi; Kashima, Isamu

2004-01-01

Low-energy trauma resulting in fractures of the distal femur is often observed in elderly patients with osteoporosis; such fractures are often associated with treatment difficulties and poor prognosis. The purpose of this study was to clarify the factors that affect the bone strength of the distal femur. We used ovariectomized mice to demonstrate bone quality factors associated with deterioration of the strength of the distal femur. Ten-week old ICR-strain mice were ovariectomized or sham-ovariectomized. Total bone mineral density (BMD), total bone area, cortical BMD, cortical thickness, and trabecular BMD were measured by peripheral quantitative computed tomography in the distal metaphyseal region of the femora. As three-dimensional architectural parameters, the trabecular number, trabecular thickness (Tb.Th), trabecular separation, and connectivity density were measured in the same region by micro-computed tomography. The maximum load measured by compression testing of the distal metaphyseal region was regarded as the bone strength of each sample. No significant differences in total bone area or in cortical BMD were found between the groups. Bone strength showed the closest relationship with total BMD (r=0.834). Multiple regression analysis demonstrated that total BMD greatly depended on cortical thickness. The addition of Tb.Th to trabecular BMD markedly reflected bone strength (R=0.857), suggesting that Tb.Th affected bone strength more significantly than trabecular BMD. These findings suggested that deterioration of bone strength of the distal femur (metaphysis) was not caused by a reduction in cortical BMD, but was related to reduced cortical thickness, which reduced total BMD, and to trabecular BMD and architecture, in particular to reduced Tb.Th. (author)

Strength Properties of Aalborg Clay

DEFF Research Database (Denmark)

Iversen, Kirsten Malte; Nielsen, Benjaminn Nordahl; Augustesen, Anders Hust

glacial time are characterised by the absence of this mussel. These deposits are named Aalborg Clay and Aalborg Sand. In the city of Aalborg, a fill layer superposes Aalborg Clay. This layer is at some places found to be 6m thick. This fill layer does not provide sufficient bearing capacity, which has...... resulted in many damaged buildings in Aalborg. To provide sufficient bearing capacity it is therefore necessary either to remove the fill or to construct the building on piles. Both methods imply that the strength of Aalborg Clay is important for the construction. This paper evaluates the strength...

Trace element composition and distribution in micron area of dinosaur eggshell fossils determined by proton microprobe

International Nuclear Information System (INIS)

Chen Youhong; Zhu Jieqing; Wang Xiaohong; Wang Yimin

1997-01-01

The scanning proton microprobe and micro-PIXE quantitative analysis technique have been used to determine composition and distribution of the trace elements in micron areas of dinosaur eggshell fossils from the stratum of Upper Cretaceous system at Nanxiong Basin in Guangdong Province, China. The study shows that the trace elements mainly include Ti, V, Cr, Mn, Co, Ni, Cu, Zn, As, Rb, Sr, Y, Zr, Sb, Ba and Pb in the micron area, but they present different distributions. While the element Sr is mainly enriched in the near surface layer, others mainly reside in the near inner layer. A preliminary discussion on the reason of the dinosaur extinction is given based on the above study

Trace element composition and distribution in micron area of dinosaur eggshell fossils determined by proton microprobe

International Nuclear Information System (INIS)

Chen Youhong; Zhu Jieqing; Wang Xiaohong; Wang Yimin

1997-01-01

The scanning proton microprobe and micro-PIXE quantitative analysis technique have been used to determine composition and distribution of the trace elements in micron areas of dinosaur eggshell fossils from the stratum of Upper Cretaceous system at Nanxiong Basin in Guangdong Province, China. The study shows that the trace elements mainly include Ti, V, Cr, Mn, Co, Ni, Cu, Zn, As, Rb, Sr, Y, Zr, Sb, Ba and Pb in the micron area, but they present different distributions. While the elements Sr is mainly enriched in the near surface layer, others mainly reside in the near inner layer. A preliminary discussion on the reason of the dinosaur extinction is given based on the above study

Mechanical strength parameters of cast iron with lamellar graphite and their significance for the design of pressure-carrying reactor components

International Nuclear Information System (INIS)

Janakiev, N.

1977-01-01

The tensile strength of thick-walled components in cast iron with lamellar graphite is lower by about 50 to 65% than that stated in DIN 1691. The usable compressive strength of this material under uni-axial load is about twice as high as its tensile strength. The graphite lamellae are not bonded into the metallic matrix. The width of the gaps between the graphite lamellae and the matrix increases with increasing wall thickness of the casting. In stress calculations for design purposes it is advisable to rely only on the permissible tensile stresses. It is shown that cast iron can be used as structural material for shieldings but is unsuitable for thick-walled reactor components carrying compressive and tensile stresses because its mechanical strength parameters decrease rapidly with increasing wall thickness. (orig.) [de

Influence of Screw Length and Bone Thickness on the Stability of Temporary Implants

Directory of Open Access Journals (Sweden)

Daniel Jogaib Fernandes

2015-09-01

Full Text Available The purpose of this work was to study the influence of screw length and bone thickness on the stability of temporary implants. A total of 96 self-drilling temporary screws with two different lengths were inserted into polyurethane blocks (n = 66, bovine femurs (n = 18 and rabbit tibia (n = 12 with different cortical thicknesses (1 to 8 mm. Screws insertion in polyurethane blocks was assisted by a universal testing machine, torque peaks were collected by a digital torquemeter and bone thickness was monitored by micro-CT. The results showed that the insertion torque was significantly increased with the thickness of cortical bone from polyurethane (p < 0.0001, bovine (p = 0.0035 and rabbit (p < 0.05 sources. Cancellous bone improved significantly the mechanical implant stability. Insertion torque and insertion strength was successfully moduled by equations, based on the cortical/cancellous bone behavior. Based on the results, insertion torque and bone strength can be estimate in order to prevent failure of the cortical layer during temporary screw placement. The stability provided by a cortical thickness of 2 or 1 mm coupled to cancellous bone was deemed sufficient for temporary implants stability.

Artificially modified collagen fibril orientation affects leather tear strength.

Science.gov (United States)

Kelly, Susyn J; Wells, Hannah C; Sizeland, Katie H; Kirby, Nigel; Edmonds, Richard L; Ryan, Tim; Hawley, Adrian; Mudie, Stephen; Haverkamp, Richard G

2018-07-01

Ovine leather has around half the tear strength of bovine leather and is therefore not suitable for high-value applications such as shoes. Tear strength has been correlated with the natural collagen fibril alignment (orientation index, OI). It is hypothesized that it could be possible to artificially increase the OI of the collagen fibrils and that an artificial increase in OI could increase tear strength. Ovine skins, after pickling and bating, were strained biaxially during chrome tanning. The strain ranged from 2 to 15% of the initial sample length, either uniformly in both directions by 10% or with 3% in one direction and 15% in the other. Once tanned, the leather tear strengths were measured and the collagen fibril orientation was measured using synchrotron-based small-angle X-ray scattering. The OI increased as a result of strain during tanning from 0.48 to 0.79 (P = 0.001) measured edge-on and the thickness-normalized tear strength increased from 27 to 43 N mm -1 (P leather was strained 10% in two orthogonal directions. This is evidence to support a causal relationship between high OI (measured edge-on), highly influenced by thickness, and tear strength. It also provides a method to produce stronger leather. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Impact of egg disinfection of hatching eggs on the eggshell microbiome and bacterial load

DEFF Research Database (Denmark)

Olsen, R.; Kudirkiene, E.; Thofner, I.

2017-01-01

Disinfection of hatching eggs is essential to ensure high quality production of broilers. Different protocols are followed in different hatcheries; however, only limited scientific evidence on how the disinfection procedures impact the microbiome is available. The aim of the present study...... was to characterize the microbiome and aerobic bacterial load of hatching eggs before disinfection and during the subsequent disinfection steps. The study included a group of visibly clean and a group of visibly dirty eggs. For dirty eggs, an initial wash in chlorine was performed, hereafter all eggs were submitted...... to two times fumigation and finally spray disinfection. The eggshell microbiome was characterized by sequencing of the total amount of 16S rRNA extracted from each sample, consisting of shell surface swabs of five eggs from the same group. In addition, the number of colony forming units (cfu) under...

Effects of essential oils on performance, egg quality, nutrient digestibility and yolk fatty acid profile in laying hens

Directory of Open Access Journals (Sweden)

Xuemei Ding

2017-06-01

Full Text Available The study was conducted to investigate the effect of essential oils on performance, egg quality, nutrient digestibility and yolk fatty acid profile in laying hens. A total of 960 Lohmann laying hens aged 53 weeks were enrolled, under 4 different treatment diets supplemented with 0, 50, 100 and 150 mg/kg essential oils (Enviva EO, Dupont Nutrition Biosciences ApS, Denmark, respectively. Each treatment was replicated 8 times with 30 birds each. Birds were fed dietary treatment diets for 12 weeks (54 to 65 weeks. For data recording and analysis, a 12-week period was divided into 3 periods of 4 weeks' duration each: period 1 (54 to 57 weeks, period 2 (58 to 61 weeks, and period 3 (62 to 65 weeks. For the diet supplemented with Enviva EO, hen-day egg production and the feed conversion ratio (FCR were significantly improved (P < 0.05 at weeks 58 to 61, and the eggshell thickness was significantly increased (P < 0.05 at week 65. However, egg production, egg weight, feed intake, FCR and other egg quality parameters (albumen height, Haugh unit, egg yolk color and eggshell strength were not affected by the dietary treatment. In addition, compared with the control diet, protein digestibility in the 100 mg/kg Enviva EO treatment group was significantly increased (P < 0.05, and fat digestibility in the 100 and 150 mg/kg Enviva EO treatment groups was significantly decreased (P < 0.05, but Enviva EO had no effect on energy apparent digestibility. Saturated fatty acid (SFA and monounsaturated fatty acid (MUFA gradually decreased and polyunsaturated fatty acid (PUFA increased with Enviva EO supplementation, but the difference was not significant. The data suggested that the supplementation of essential oils (Enviva EO in laying hen diet did not show a significant positive effect on performance and yolk fatty acid composition but it tended to increase eggshell thickness and protein digestibility, especially at the dose of 50 mg/kg.

Nutritional Supplement of Hatchery Eggshell Membrane Improves Poultry Performance and Provides Resistance against Endotoxin Stress.

Directory of Open Access Journals (Sweden)

S K Makkar

Full Text Available Eggshells are significant part of hatchery waste which consist of calcium carbonate crust, membranes, and proteins and peptides of embryonic origins along with other entrapped contaminants including microbes. We hypothesized that using this product as a nutritional additive in poultry diet may confer better immunity to the chickens in the paradigm of mammalian milk that enhances immunity. Therefore, we investigated the effect of hatchery eggshell membranes (HESM as a short term feed supplement on growth performance and immunity of chickens under bacterial lipopolysaccharide (LPS challenged condition. Three studies were conducted to find the effect of HESM supplement on post hatch chickens. In the first study, the chickens were fed either a control diet or diets containing 0.5% whey protein or HESM as supplement and evaluated at 5 weeks of age using growth, hematology, clinical chemistry, plasma immunoglobulins, and corticosterone as variables. The second and third studies were done to compare the effects of LPS on control and HESM fed birds at 5 weeks of age following at 4 and 24 h of treatment where the HESM was also sterilized with ethanol to deplete bacterial factors. HESM supplement caused weight gain in 2 experiments and decreased blood corticosterone concentrations. While LPS caused a significant loss in body weight at 24 h following its administration, the HESM supplemented birds showed significantly less body weight loss compared with the control fed birds. The WBC, heterophil/lymphocyte ratio, and the levels of IgG were low in chickens fed diets with HESM supplement compared with control diet group. LPS challenge increased the expression of pro-inflammatory cytokine gene IL-6 but the HESM fed birds showed its effect curtailed, also, which also, favored the up-regulation of anti-inflammatory genes compared with control diet fed chickens. Post hatch supplementation of HESM appears to improve performance, modulate immunity, and increase

Addition of Silica Fume to Improve Strength of Cement Paste

Science.gov (United States)

Chen, Jiajian; Chen, Hongniao; Li, Gu

2018-03-01

This study measured the packing densities of 0 to 30% silica fume (SF) added cementitious materials and strength of the cementitious pastes with various water content. The results revealed that addition of silica fume up to a certain level has great effects on packing density and strength. In-depth analysis illustrated that a lower W/CM ratio would not always result in a higher cube strength, and the range between 0.05 and 0.07 µm would be the amount of water film thickness (WFT) for muximum strength.

Section thickness-dependent tensile properties of squeeze cast magnesium alloy AM60

Directory of Open Access Journals (Sweden)

Xuezhi Zhang

2012-05-01

Full Text Available The development of alternative casting processes is essential for the high demand of light weight magnesium components to be used in the automotive industry, which often contain different section thicknesses. Squeeze casting with its inherent advantages has been approved for the capability of minimizing the gas porosity in magnesium alloys. For advanced engineering design of light magnesium automotive applications, it is critical to understand the effect of section thickness on mechanical properties of squeeze cast magnesium alloys. In this study, magnesium alloy AM60 with different section thicknesses of 6, 10 and 20 mm squeeze cast under an applied pressure of 30 MPa was investigated. The prepared squeeze cast AM60 specimens were tensile tested at room termperature. The results indicate that the mechanical properties including yield strength (YS, ultimate tensile strength (UTS and elongation (A decrease with an increase in section thickness of squeeze cast AM60. The microstructure analysis shows that the improvement in the tensile behavior of squeeze cast AM60 is primarily attributed to the low-gas porosity level and fine grain strucuture which result from the variation of cooling rate of different section thickness. The numerical simulation (Magmasoft? was employed to determine the solidification rates of each step, and the simulated results show that the solidification rate of the alloy decreases with an increase in the section thickness. The computed solidification rates support the experimental observation on grain structural development.

Facile and controllable construction of vanadium pentoxide@conducting polymer core/shell nanostructures and their thickness-dependent synergistic energy storage properties

International Nuclear Information System (INIS)

Tong, Zhongqiu; Liu, Shikun; Li, Xingang; Ding, Yanbo; Zhao, Jiupeng; Li, Yao

2016-01-01

Graphical abstract: Here, we report a novel approach to prepare metal oxide@conducting polymer core/shell hybrids with controlled shell thickness and morphology, and the influence of PANI shell thickness on the electrochemical performance of V 2 O 5 @PANI core/shell hybrids is systematically investigated. Thickness-dependent synergistic electron transport, Li-ion diffusion distance, and shell mechanical strength mechanisms are proposed. - Highlights: • Thickness- and morphology-controlled V 2 O 5 /PANI core/shell hybrid nanofibers are fabricated. • The enhancement of energy storage performance of core/shell hybrids varies with the shell thickness. • Thickness-dependent synergistic electron transport, Li-ion diffusion distances, and shell mechanical strength mechanisms are proposed. - Abstract: Thickness- and morphology-controlled vanadium pentoxide/polyaniline (V 2 O 5 /PANI) core/shell hybrid nanofibers are fabricated by electropolymerization of PANI on V 2 O 5 nanofibers for enhanced energy storage. By simply adjusting the electrodeposition time, the thickness of the PANI shells can be controlled from 5 nm to 47 nm, and the morphology can be changed from coaxial to branched. The influence of shell thickness on the improved Li-ion storage performance of the V 2 O 5 /PANI core/shell nanofibers is systematically investigated, and this enhancement of charge capability and cycling stability strongly varies with the shell thickness. Thickness-dependent synergistic electron transport, Li-ion diffusion distances, and shell mechanical strength mechanisms are also proposed. These results provide meaningful references for developing new functional core/shell materials and high-performance energy storage composite materials.

Characterization of compressive and short beam shear strength of bamboo opened cell foam core sandwich composites

Energy Technology Data Exchange (ETDEWEB)

Setyawan, Paryanto Dwi, E-mail: paryanto-ds@yahoo.com; Sugiman,; Saputra, Yudhi [Department of Mechanical Engineering, Faculty of Engineering, University of Mataram, Mataram, West Nusa Tenggara (Indonesia)

2016-03-29

The paper presents the compressive and the short beam shear strength of a sandwich composite with opened cell foam made of bamboo fiber as the core and plywood as the skins. The core thickness was varied from 10 mm to 40 mm keeping the volume fraction of fiber constant. Several test s were carried out including the core density, flatwise compressive and the short beam shear testing in three point bending. The results show that the density of bamboo opened cell foam is comparable with commercial plastic foam, such as polyurethane foam. The compressive strength tends to increase linearly with increasing the core thickness. The short beam shear failure load of the sandwich composite increases with the increase of core thickness, however on the contrary, the short beam shear strength which tends to sharply decrease from the thickness of 10 mm to 30 mm and then becomes flat.

Influence of colorant and film thickness on thermal aging characteristics of oxo-biodegradable plastic bags

Science.gov (United States)

Leuterio, Giselle Lou D.; Pajarito, Bryan B.; Domingo, Carla Marie C.; Lim, Anna Patricia G.

2016-05-01

Functional, lightweight, strong and cheap plastic bags incorporated with pro-oxidants undergo accelerated degradation under exposure to heat and oxygen. This work investigated the effect of colorant and film thickness on thermal aging characteristics of commercial oxo-biodegradable plastic bag films at 70 °C. Degradation is monitored through changes in infrared absorption, weight, and tensile properties of thermally aged films. The presence of carbonyl band in infrared spectrum after 672 h of thermal aging supports the degradation behavior of exposed films. Results show that incorporation of colorant and increasing thickness exhibit low maximum weight uptake. Titanium dioxide as white colorant in films lowers the susceptibility of films to oxygen uptake but enhances physical degradation. Higher amount of pro-oxidant loading also contributes to faster degradation. Opaque films are characterized by low tensile strength and high elastic modulus. Decreasing the thickness contributes to lower tensile strength of films. Thermally aged films with colorant and low thickness promote enhanced degradation.

Optimisation and characterisation of tungsten thick coatings on copper based alloy substrates

Science.gov (United States)

Riccardi, B.; Montanari, R.; Casadei, M.; Costanza, G.; Filacchioni, G.; Moriani, A.

2006-06-01

Tungsten is a promising armour material for plasma facing components of nuclear fusion reactors because of its low sputter rate and favourable thermo-mechanical properties. Among all the techniques able to realise W armours, plasma spray looks particularly attractive owing to its simplicity and low cost. The present work concerns the optimisation of spraying parameters aimed at 4-5 mm thick W coating on copper-chromium-zirconium (Cu,Cr,Zr) alloy substrates. Characterisation of coatings was performed in order to assess microstructure, impurity content, density, tensile strength, adhesion strength, thermal conductivity and thermal expansion coefficient. The work performed has demonstrated the feasibility of thick W coatings on flat and curved geometries. These coatings appear as a reliable armour for medium heat flux plasma facing component.

Optimisation and characterisation of tungsten thick coatings on copper based alloy substrates

International Nuclear Information System (INIS)

Riccardi, B.; Montanari, R.; Casadei, M.; Costanza, G.; Filacchioni, G.; Moriani, A.

2006-01-01

Tungsten is a promising armour material for plasma facing components of nuclear fusion reactors because of its low sputter rate and favourable thermo-mechanical properties. Among all the techniques able to realise W armours, plasma spray looks particularly attractive owing to its simplicity and low cost. The present work concerns the optimisation of spraying parameters aimed at 4-5 mm thick W coating on copper-chromium-zirconium (Cu,Cr,Zr) alloy substrates. Characterisation of coatings was performed in order to assess microstructure, impurity content, density, tensile strength, adhesion strength, thermal conductivity and thermal expansion coefficient. The work performed has demonstrated the feasibility of thick W coatings on flat and curved geometries. These coatings appear as a reliable armour for medium heat flux plasma facing component

Optimisation and characterisation of tungsten thick coatings on copper based alloy substrates

Energy Technology Data Exchange (ETDEWEB)

Riccardi, B. [Associazione Euratom-ENEA sulla Fusione, CR Frascati, P.B. 65 00044 Frascati, Roma (Italy)]. E-mail: riccardi@frascati.enea.it; Montanari, R. [Dipartimento di Ingegneria Meccanica, Universita di Roma, Tor Vergata, 00133 Roma (Italy); Casadei, M. [Centro Sviluppo Materiali, 00100 Roma (Italy); Costanza, G. [Dipartimento di Ingegneria Meccanica, Universita di Roma, Tor Vergata, 00133 Roma (Italy); Filacchioni, G. [ENEA CR Casaccia, I-00060 S. M. di Galeria, Roma (Italy); Moriani, A. [Associazione Euratom-ENEA sulla Fusione, CR Frascati, P.B. 65 00044 Frascati, Roma (Italy)

2006-06-30

Tungsten is a promising armour material for plasma facing components of nuclear fusion reactors because of its low sputter rate and favourable thermo-mechanical properties. Among all the techniques able to realise W armours, plasma spray looks particularly attractive owing to its simplicity and low cost. The present work concerns the optimisation of spraying parameters aimed at 4-5 mm thick W coating on copper-chromium-zirconium (Cu,Cr,Zr) alloy substrates. Characterisation of coatings was performed in order to assess microstructure, impurity content, density, tensile strength, adhesion strength, thermal conductivity and thermal expansion coefficient. The work performed has demonstrated the feasibility of thick W coatings on flat and curved geometries. These coatings appear as a reliable armour for medium heat flux plasma facing component.

Effects of thickness and surface roughness on mechanical properties of aluminum sheets

International Nuclear Information System (INIS)

Suh, Chang Hee; Jung, Yun Chul; Kim, Young Suk

2010-01-01

The effect of thickness on the mechanical properties of Al 6K21-T4 sheet specimens under uniaxial tension was investigated. In order to reduce the thickness of the specimens without changing the microstructure and grain size, chemical etching was carried out, resulting in Al sheets ranging from 0.40 mm to 1.58 mm in thickness. Additionally, the effect of surface roughness was determined by finite element (FE) calculations performed using FE code MARC 2007. Tensile specimens of varying surface roughness were modeled and simulated. An analysis of the combined effects of the thickness and surface roughness revealed that the yield and tensile strengths decreased when the number of grains over the thickness was decreased. The ductility also decreased when reducing the thickness. An FE simulation showed that both the surface roughness and thickness affected the flow-curve shape. Moreover, the effect of the surface roughness tended to increase when decreasing the sheet thickness of specimens having the same roughness

Organochlorine contaminants and reproductive success of double-crested cormorants from Green Bay, Wisconsin, USA

Science.gov (United States)

Custer, T.W.; Custer, Christine M.; Hines, R.K.; Gutreuter, S.; Stromborg, K.L.; Allen, P. David; Melancon, M.J.

1999-01-01

In 1994 and 1995, nesting success of double-crested cormorants (Phalacrocorax auritus) was measured at Cat Island, in southern Green Bay, Lake Michigan, Wisconsin, USA. Sample eggs at pipping and unhatched eggs were collected and analyzed for organochlorines (including total polychlorinated biphenyls [PCBs] and DDE), hepatic microsomal ethoxyresorufin-O-dealkylase (EROD) activity in embryos, and eggshell thickness. Of 1,570 eggs laid, 32% did not hatch and 0.4% had deformed embryos. Of 632 chicks monitored from hatching to 12 d of age, 9% were missing or found dead; no deformities were observed. The PCB concentrations in sample eggs from clutches with deformed embryos (mean = 10.2 μg/g wet weight) and dead embryos (11.4 μg/g) were not significantly higher than concentrations in sample eggs from nests where all eggs hatched (12.1 μg/g). A logistic regression of hatching success versus DDE, dieldrin, and PCB concentrations in sibling eggs identified DDE and not dieldrin or PCBs as a significant risk factor. A logistic regression of hatching success versus DDE and eggshell thickness implicated DDE and not eggshell thickness as a significant risk factor. Even though the insecticide DDT was banned in the early 1970s, we suggest that DDE concentrations in double-crested cormorant eggs in Green Bay are still having an effect on reproduction in this species.

Study of strength of Dsub(y)150 gate valve case, manufactured by centrifugal casting

International Nuclear Information System (INIS)

Umanskaya, L.G.; Semenov, P.V.; Tinyakov, V.G.; Babkina, R.I.; Khatuntsev, Eh.V.

1982-01-01

A process for manufacturing centrifugal-cast gate valve body is developed. Structural strength of such items, homogeneity, ductile and strength properties over the cross section as well as the metal susceptibility to embrittlement have been investigated. Three cast gate valve bodies have been taken: one - of 20GSL steel - for hydraulic testing, and two - of 15Kh1MFL steel - for investigation into the metal properties across the valve thickness. The strength properties of the centrifugal-cast gate valve body of 15Kh1M1FL steel are stated to meet the specifications. The gate valve metal ductility (delta and PSI) is twice as high as that of a sand-cast valve. The microstructure, strength and ductility are uniform both over wall thickness and over different body cross sections

Adhesive properties and adhesive joints strength of graphite/epoxy composites

Science.gov (United States)

Rudawska, Anna; Stančeková, Dana; Cubonova, Nadezda; Vitenko, Tetiana; Müller, Miroslav; Valášek, Petr

2017-05-01

The article presents the results of experimental research of the adhesive joints strength of graphite/epoxy composites and the results of the surface free energy of the composite surfaces. Two types of graphite/epoxy composites with different thickness were tested which are used to aircraft structure. The single-lap adhesive joints of epoxy composites were considered. Adhesive properties were described by surface free energy. Owens-Wendt method was used to determine surface free energy. The epoxy two-component adhesive was used to preparing the adhesive joints. Zwick/Roell 100 strength device were used to determination the shear strength of adhesive joints of epoxy composites. The strength test results showed that the highest value was obtained for adhesive joints of graphite-epoxy composite of smaller material thickness (0.48 mm). Statistical analysis of the results obtained, the study showed statistically significant differences between the values of the strength of the confidence level of 0.95. The statistical analysis of the results also showed that there are no statistical significant differences in average values of surface free energy (0.95 confidence level). It was noted that in each of the results the dispersion component of surface free energy was much greater than polar component of surface free energy.

Cyclic fatigue of a high-strength corrosion-resistant sheet TRIP steel

Science.gov (United States)

Terent'ev, V. F.; Alekseeva, L. E.; Korableva, S. A.; Prosvirnin, D. V.; Pankova, M. N.; Filippov, G. A.

2014-04-01

The mechanical properties of 0.3- and 0.8-mm-thick high-strength corrosion-resistant TRIP steel having various levels of strength properties are studied during static and cyclic loading in the high-cycle fatigue range. The fatigue fracture surface is analyzed by fractography, and the obtained results demonstrate ductile and quasi-brittle fracture mechanisms of this steel depending on the strength properties of the steel and the content of deformation martensite in it.

Smoluchowski coagulation models of sea ice thickness distribution dynamics

Science.gov (United States)

Godlovitch, D.; Illner, R.; Monahan, A.

2011-12-01

Sea ice thickness distributions display a ubiquitous exponential decrease with thickness. This tail characterizes the range of ice thickness produced by mechanical redistribution of ice through the process of ridging, rafting, and shearing. We investigate how well the thickness distribution can be simulated by representing mechanical redistribution as a generalized stacking process. Such processes are naturally described by a well-studied class of models known as Smoluchowski Coagulation Models (SCMs), which describe the dynamics of a population of fixed-mass "particles" which combine in pairs to form a "particle" with the combined mass of the constituent pair at a rate which depends on the mass of the interacting particles. Like observed sea ice thickness distributions, the mass distribution of the populations generated by SCMs has an exponential or quasi-exponential form. We use SCMs to model sea ice, identifying mass-increasing particle combinations with thickness-increasing ice redistribution processes. Our model couples an SCM component with a thermodynamic component and generates qualitatively accurate thickness distributions with a variety of rate kernels. Our results suggest that the exponential tail of the sea ice thickness distribution arises from the nature of the ridging process, rather than specific physical properties of sea ice or the spatial arrangement of floes, and that the relative strengths of the dynamic and thermodynamic processes are key in accurately simulating the rate at which the sea ice thickness tail drops off with thickness.

The timing of ostrich existence in Central Asia: AMS 14C age of eggshells from Mongolia and southern Siberia (a pilot study)

International Nuclear Information System (INIS)

Kurochkin, Evgeny N.; Kuzmin, Yaroslav V.; Antoshchenko-Olenev, Igor V.; Zabelin, Vladimir I.; Krivonogov, Sergey K.; Nohrina, Tatiana I.; Lbova, Ludmila V.; Burr, G.S.; Cruz, Richard J.

2010-01-01

The presence of Asiatic ostrich in Central Asia in the later Cenozoic time is well-documented; nevertheless, a few direct age determinations existed until recently. We performed AMS 14 C dating of ostrich eggshells found in Mongolia, Transbaikal, and Tuva. It shows that ostriches existed throughout the second part of Late Pleistocene, until the Late Glacial time (ca. 13,000-10,100 BP). It seems that Asiatic ostrich went extinct in Central Asia just before or even in the Holocene.

An experimental assessment of the size effects on the strength and ductility of freestanding copper films under macroscopically homogenous deformation

Science.gov (United States)

Chauhan, Shakti Singh

Metallic interconnects and circuitry has been experiencing excessive deformation beyond their elastic limits in many applications, ranging from micro-electromechanical systems (MEMS) to flexible electronics. These broad applications are creating needs to understand the extent of strength and ductility of freestanding metallic films at scales approaching the micron and sub micron range. This work aims to elucidate the effects of microstructural constraint as well as geometric dimensional constraint on the strength and ductility of freestanding Cu films under uniaxial tension. Two types of films are tested (i) high purity rolled films of 12.5-100microm thickness and average grain sizes of 11-47microm and (ii) electroplated films of 2-50 microm thickness and average grain sizes of 1.8-5microm. Several experimental tools including residual electrical resistivity measurements, surface strain measurements and surface roughness measurements are employed to highlight the underlying deformation mechanisms leading to the observed size effects. With respect to the strength of the specimens, we find that the nature and magnitude of thickness effects is very sensitive to the average grain size. In all cases, coupled thickness and grain size effects were observed. This study shows that this observed coupling, unique to the case of freestanding specimen, arises because the observed size effects are an outcome of the size dependence of two fundamental microstructural parameters i.e. volume fraction of surface grains and grain boundary area per unit specimen volume. For films having thickness and grain sizes greater than 5microm, thickness dependent weakening is observed for a constant grain size. Reducing thickness results in an increase in the volume fraction of grains exposed to the free surface as well as a reduction in the grain boundary area per unit specimen volume. The former effect leads to a reduction in the effective microstructural constraint on the intragranular

The Bending Strength, Internal Bonding and Thickness Swelling of a Five Layer Sandwiched Bamboo Particleboard

Science.gov (United States)

Jamaludin, M. A.; Bahari, S. A.; Nordin, K.; Soh, T. F. T.

2010-03-01

The demand for wood based material is increasing but the supply is decreasing. Therefore the price of these raw materials has increased. Bamboo provides an economically feasible alternative raw material for the wood based industry. Its properties are comparable to wood. It is also compatible with the existing processing technology. Bamboo is in abundance, easy to propagate and of short maturation period. Bamboo provides a cheaper alternative resource for the wood based industry. The development of new structural components from bamboo will widen its area of application from handicrafts to furniture and building components. In this study, five layer sandwiched bamboo particleboard were manufactured. The sandwiched Bamboo PB consists of a bamboo PB core, oil palm middle veneers and thin meranti surface veneers. The physical and mechanical properties of the bamboo sandwiched particleboards were tested in accordance to the BS-EN 317:1993 [1] and BS-EN 310:1993 [2], respectively. All the samples passed the standards. The modulus of elasticity was about 352% higher than the value specified in the BS standard, BS-EN 312-4:1996 [3]. The Internal bonding was about 23% higher than the general requirements specified in the standard. On the other hand, the thickness swelling was about 6% lower than the standard. No glue line failure was observed in the strength tests. Critical failures in the IB tests were observed in the particleboards. Tension failures were observed in the surface veneers in the bending tests. The five layer sandwiched bamboo particleboard can be used for light weight construction such as furniture, and wall and door panels in buildings.

Effects of Partial Replacement of Eggshell Powder by Halloysite Nanotubes on the Properties of Polyvinyl Alcohol Composites

Science.gov (United States)

Alias, N. F.; Ismail, H.

2018-06-01

Polyvinyl alcohol (PVA)/eggshell powder (ESP) were prepared via solution casting method. The effects of gradual replacement of ESP by halloysite nanotubes (HNTs) were investigated based on tensile properties, physical properties and biodegradability. The main objective is to study the effect of hybrid fillers and also to compare the properties of PVA/ESP composite with conventional filler, HNT. The tensile properties decreased with increasing HNT loading. Scanning electron microscopy (SEM) studies showed that agglomeration of filler were present throughout the composites. Due to the presence of hydroxyl group on the outer and inner surface of HNT, the water absorption and water vapor transmisibility were found to increase with increasing HNTs loading. The biodegradability of film filled with HNT is lower compared to the film filled with ESP.

Study of in vitro bioactivity and mechanical properties of diopside nano-bioceramic synthesized by a facile method using eggshell as raw material

Energy Technology Data Exchange (ETDEWEB)

Kazemi, Amirhossein [Advanced Materials Research Center, Department of Materials Engineering, Najafabad Branch, Islamic Azad University, Najafabad (Iran, Islamic Republic of); Abdellahi, Majid, E-mail: Abdellahi@Pmt.iaun.ac.ir [Advanced Materials Research Center, Department of Materials Engineering, Najafabad Branch, Islamic Azad University, Najafabad (Iran, Islamic Republic of); Khajeh-Sharafabadi, Armina [Advanced Materials Research Center, Department of Materials Engineering, Najafabad Branch, Islamic Azad University, Najafabad (Iran, Islamic Republic of); Khandan, Amirsalar; Ozada, Neriman [Mechanical Engineering Department, Eastern Mediterranean University, North Cyprus, Gazimağusa, TRNC, Mersin 10 (Turkey)

2017-02-01

In this study, diopside bioceramic was synthesized using a mechanical milling process and subsequent heat treatment. The simplicity of experiments and also the high energy available in ball milling lead to rapid synthesis of the products in comparison with other synthesis methods. Magnesium oxide (MgO), silicon dioxide (SiO{sub 2}) and eggshell (as the calcium source) powders were weighted in stoichiometric conditions and milled to initial activation of the surface of the powder's mixture. Then a sintering process was conducted to complete formation of diopside nanopowder and also evaluates its thermal stability. The mechanisms occurred during the synthesis of this bioceramic were carefully investigated. X-Ray diffraction analysis (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), thermogravimetry (TG), differential thermal analysis (DTA), and inductive coupled plasma atomic emission spectroscopy (ICP-AES) were used for gathering and analyzing data. The ability and rate of apatite formation on the sample surface were evaluated by Simulated Body Fluid (SBF) test, a method that is well recognized to characterize the in vitro bioactivity of ceramic materials. According to the results obtained, the diopside samples had a significant potential to form apatite layer on their surface during soaking in the SBF solution. Besides, the bonding strength of this bioceramic was about 350 ± 7 MPa which was almost more than three times of that reported for hydroxyapatite. An excellent fracture toughness of 4 ± 0.3 MPa m{sup 0.5} was also obtained for this ceramic which was higher than that of previously reported works. - Highlights: • Diopside was synthesized using a mechanical milling process and subsequent heat treatment. • The mechanisms occurred during the synthesis of this bioceramic were carefully investigated. • The bonding strength of diopside samples prepared in this study was about 350 ± 7 MPa. • The fracture toughness of

High-performance biodegradable polylactide composites fabricated using a novel plasticizer and functionalized eggshell powder.

Science.gov (United States)

Kong, Junjun; Li, Yi; Bai, Yungang; Li, Zonglin; Cao, Zengwen; Yu, Yancun; Han, Changyu; Dong, Lisong

2018-06-01

A novel polyester poly(diethylene glycol succinate) (PDEGS) was synthesized and evaluated as a plasticizer for polylactide (PLA) in this study. Meanwhile, an effective sustainable filler, functionalized eggshell powder (FES) with a surface layer of calcium phenyphosphonate was also prepared. Then, PLA biocomposites were prepared from FES and PDEGS using a facile melt blending process. The addition of 15 wt% PDEGS as plasticizer showed good miscibility with PLA macromolecules and increased the chain mobility of PLA. The crystallization kinetics of PLA composites revealed that the highly effective nucleating FES significantly improved the crystallization ability of PLA at both of non-isothermal and isothermal conditions. In addition, the effective plasticizer and well-dispersed FES increased the elongation at break from 6% of pure PLA to over 200% for all of the plasticized PLA composites. These biodegradable PLA biocomposites, coupled with excellent crystallization ability and tunable mechanical properties, demonstrate their potential as alternatives to traditional commodity plastics. Copyright © 2018 Elsevier B.V. All rights reserved.

Properties of PETP track membranes of different thickness

International Nuclear Information System (INIS)

Apel, P.Yu.; Didyk, A.Yu.; Larionova, I.E.; Mamonova, T.I.; Orelovich, O.L.; Samoilova, L.I.; Yanina, I.V.; Zhitariuk, N.I.

1994-01-01

The basic properties of polyethylene terephthalate (PETP) track membranes (TM) made of the films with the thickness of 10 and 20 μm are investigated. The membranes with the pore diameters of 0.2, 0.4 and 1 μm were chosen for comparative study. The porous structure of the membranes was characterized by the following set of parameters: pore density, pore size, bubble point, pore radius distribution measured by the Coulter porometer. The tensile strength, water and gas flow rate were determined for both types of the TMs. The filtration processes of liquid and gaseous media were investigated. Advantages and disadvantages of 'thin' and 'thick' TM are discussed. (author). 4 refs, 5 figs, 3 tabs

Influence of SiC coating thickness on mechanical properties of SiCf/SiC composite

Science.gov (United States)

Yu, Haijiao; Zhou, Xingui; Zhang, Wei; Peng, Huaxin; Zhang, Changrui

2013-11-01

Silicon carbide (SiC) coatings with varying thickness (ranging from 0.14 μm to 2.67 μm) were deposited onto the surfaces of Type KD-I SiC fibres with native carbonaceous surface using chemical vapour deposition (CVD) process. Then, two dimensional SiC fibre reinforced SiC matrix (2D SiCf/SiC) composites were fabricated using polymer infiltration and pyrolysis (PIP) process. Influences of the fibre coating thickness on mechanical properties of SiC fibre and SiCf/SiC composite were investigated using single-filament test and three-point bending test. The results indicated that flexural strength of the composites initially increased with the increasing CVD SiC coating thickness and reached a peak value of 363 MPa at the coating thickness of 0.34 μm. Further increase in the coating thickness led to a rapid decrease in the flexural strength of the composites. The bending modulus of composites showed a monotonic increase with increasing coating thickness. A chemical attack of hydrogen or other ions (e.g. a C-H group) on the surface of SiC fibres during the coating process, owing to the formation of volatile hydrogen, lead to an increment of the surface defects of the fibres. This was confirmed by Wang et al. [35] in their work on the SiC coating of the carbon fibre. In the present study, the existing ˜30 nm carbon on the surface of KD-I fibre [36] made the fibre easy to be attacked. Deposition of non-stoichiometric SiC, causing a decrease in strength. During the CVD process, a small amount of free silicon or carbon always existed [35]. The existence of free silicon, either disordered the structure of SiC and formed a new source of cracks or attacked the carbon on fibre surface resulting in properties degeneration of the KD-I fibre. The effect of residual stress. The different thermal expansion coefficient between KD-I SiC fibre and CVD SiC coating, which are 3 × 10-6 K-1 (RT ˜ 1000 °C) and 4.6 × 10-6 K-1 (RT ˜ 1000 °C), respectively, could cause residual stress

High-strength laser welding of aluminum-lithium scandium-doped alloys

Science.gov (United States)

Malikov, A. G.; Ivanova, M. Yu.

2016-11-01

The work presents the experimental investigation of laser welding of an aluminum alloy (system Al-Mg-Li) and aluminum alloy (system Al-Cu-Li) doped with Sc. The influence of nano-structuring of the surface layer welded joint by cold plastic deformation on the strength properties of the welded joint is determined. It is founded that, regarding the deformation degree over the thickness, the varying value of the welded joint strength is different for these aluminum alloys. The strength of the plastically deformed welded joint, aluminum alloys of the Al-Mg-Li and Al-Cu-Li systems reached 0.95 and 0.6 of the base alloy strength, respectively.

Charge Distribution Dependency on Gap Thickness of CMS Endcap RPC

CERN Document Server

Park, Sung K.; Lee, Kyongsei

2016-01-01

We report a systematic study of charge distribution dependency of CMS Resistive Plate Chamber (RPC) on gap thickness. Prototypes of double-gap RPCs with six different gap thickness ranging from from 1.0 to 2.0 mm in 0.2-mm steps have been built with 2-mm-thick phenolic high-pressure-laminated plates. The efficiencies of the six gaps are measured as a function of the effective high voltages. We report that the strength of the electric fields of the gap is decreased as the gap thickness is increased. The distributions of charges in six gaps are measured. The space charge effect is seen in the charge distribution at the higher voltages. The logistic function is used to fit the charge distribution data. Smaller charges can be produced within smaller gas gap. But the digitization threshold should be also lowered to utilize these smaller charges.

The influence of annealing temperature on the strength of TRISO coated particles

International Nuclear Information System (INIS)

Rooyen, I.J. van; Neethling, J.H.; Rooyen, P.M. van

2010-01-01

The integrity of the Pebble Bed Modular Reactor (PBMR) fuel, and specifically the SiC layer system of the Tristructural Isotropic (TRISO) coated particle (CP), namely inner pyrolytic carbon, silicon carbide and outer pyrolytic carbon (I-PyC-SiC-O-PyC), determines the containment of fission products. The PBMR fuel consists of TRISO coated particles (CPs) embedded in a graphite matrix. One of the characterization techniques investigated by PBMR is the determination of strength of CPs. It is a well known metallurgical fact that temperature, amongst many other parameters, may influence the strength of a material. A recently developed method for measuring the strength of the TRISO coated particles was used and is briefly described in this article. The advantages of this method are demonstrated by the comparison of strength measurements of five experimental PBMR CP batches as a function of annealing temperature. Significant modification of strength after annealing was measured with increased temperature within the range 1000-2100 o C. The interesting feature of decreasing standard deviation of the strength with increasing temperature will also be discussed with a possible explanation. A significant difference in coated particle strength is also demonstrated for two CP batches with layer thickness on the extremities of the SiC layer thickness specification. The effect of long duration annealing on these strength values will also be demonstrated by comparing results from 1 h to 100 h annealing periods of coated particles at a temperature of 1600 o C.

Osmocapsules for direct measurement of osmotic strength.

Science.gov (United States)

Kim, Shin-Hyun; Lee, Tae Yong; Lee, Sang Seok

2014-03-26

Monodisperse microcapsules with ultra-thin membranes are microfluidically designed to be highly sensitive to osmotic pressure, thereby providing a tool for the direct measurement of the osmotic strength. To make such osmocapsules, water-in-oil-in-water double-emulsion drops with ultra-thin shells are prepared as templates through emulsification of core-sheath biphasic flow in a capillary microfluidic device. When photocurable monomers are used as the oil phase, the osmocapsules are prepared by in-situ photopolymerization of the monomers, resulting in semipermeable membranes with a relatively large ratio of membrane thickness to capsule radius, approximately 0.02. These osmocapsules are buckled by the outward flux of water when they are subjected to a positive osmotic pressure difference above 125 kPa. By contrast, evaporation-induced consolidation of middle-phase containing polymers enables the production of osmocapsules with a small ratio of membrane thickness to capsule radius of approximately 0.002. Such an ultra-thin membrane with semi-permeability makes the osmocapsules highly sensitive to osmotic pressure; a positive pressure as small as 12.5 kPa induces buckling of the capsules. By employing a set of distinct osmocapsules confining aqueous solutions with different osmotic strengths, the osmotic strength of unknown solutions can be estimated through observation of the capsules that are selectively buckled. This approach provides the efficient measurement of the osmotic strength using only a very small volume of liquid, thereby providing a useful alternative to other measurement methods which use complex setups. In addition, in-vivo measurement of the osmotic strength can be potentially accomplished by implanting these biocompatible osmocapsules into tissue, which is difficult to achieve using conventional methods. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

First chelonian eggs and carapace fragments from the Pliocene of Rhodes, Greece

DEFF Research Database (Denmark)

Mueller-Töwe, Inken J.; Kjeldahl-Vallon, Tina A.; Milàn, Jesper

2011-01-01

Well-preserved fossil eggs and eggshell fragments from the Pliocene Apolakkia Formation of Rhodes (Greece) are described. The eggs were found in-situ in a clutch. They are sub-spherical with lengths of 53-60 mm and widths of about 40 mm. All eggs are diagenetically compressed and their original...... diameters are estimated at 45-50 mm. The eggshells are 0.3-0.5 mm thick, partly recrystallized, but widely still aragonitic. They consist of needle-like crystals that form individual shell units. A few pores are preserved between these shell units. This shell-structure allows assignment to chelonian eggs...... in the oofamily Testudoolithidae and the oogenus Testudolithus. The external morphology, microstructure and mineralogical composition of the eggshells show close resemblance to eggs of the extant tortoise Geochelone elephantopus. Together with a small association of turtle carapace fragments from the same...

Construction strength analysis of landing craft tank conversion to passenger ship using finite element method

Science.gov (United States)

Nurul Misbah, Mohammad; Setyawan, Dony; Murti Dananjaya, Wisnu

2018-03-01

This research aims to determine the longitudinal strength of passenger ship which was converted from Landing Craft Tank with 54 m of length as stated by BKI (Biro Klasifikasi Indonesia / Indonesian Classification Bureau). Verification of strength value is done to 4 (four) loading conditions which are (1) empty load condition during sagging wave, (2) empty load condition during hogging wave, (3) full load condition during sagging wave and (4) full load condition during hogging wave. Analysis is done using Finite Element Analysis (FEA) software by modeling the entire part of passenger ship and its loading condition. The back and upfront part of ship centerline were used as the boundary condition. From that analysis it can be concluded that the maximum stress for load condition (1) is 72,393 MPa, 74,792 MPa for load condition (2), 129,92 MPa for load condition (3), and 132,4 MPa for load condition (4). Longitudinal strength of passenger ship fulfilled the criteria of empty load condition having smaller stress value than allowable stress which is 90 MPa, and during full load condition with smaller stress value than allowable stress which is 150 MPa. Analysis on longitudinal strength comparison with entire ship plate thickness variation of ± 2 mm from initial plate was also done during this research. From this research it can be concluded that plate thickness reduction causes the value of longitudinal strength to decrease, while plate thickness addition causes the value of longitudinal strength to increase.

Laminated Ti-Al composites: Processing, structure and strength

DEFF Research Database (Denmark)

Du, Yan; Fan, Guohua; Yu, Tianbo

2016-01-01

Laminated Ti-Al composite sheets with different layer thickness ratios have been fabricated through hot pressing followed by multi-pass hot rolling at 500 °C.The laminated sheets show strong bonding with intermetallic interface layers of nanoscale thickness between the layers of Ti and Al....... The mechanical properties of the composites with different volume fractions of Al from 10% to 67% show a good combination of strength and ductility. A constraint strain in the hot-rolled laminated structure between the hard and soft phases introduces an elastic-plastic deformation stage, which becomes more...

comparative analysis of the compressive strength of hollow

African Journals Online (AJOL)

user

2016-04-02

Apr 2, 2016 ... Previous analysis showed that cavity size and number on one hand and combinations thickness affect the compressive strength of hollow sandcrete blocks. Series arrangement of the cavities is common but parallel arrangement has been recommended. This research performed a comparative analysis of ...

Effect of production system and flock age on eggshell and egg internal quality measurements.

Science.gov (United States)

Samiullah, Sami; Omar, Amal Saleh; Roberts, Juliet; Chousalkar, Kapil

2017-01-01

Egg quality was measured in eggs from different flocks that were reared together and then allocated to different production systems. Eggs were processed for measurements of eggshell and egg internal quality variables, scoring of ultrastructural mammillary layer features, completeness of cuticle cover, and protoporphyrin IX (PP IX) quantification. There was a significant main effect (P egg weight, and egg internal quality and significant effects of flock age on most measurements. The mammillary layer ultrastructural variables showed no clear relationship with production system and flock age. However, there was a significant interaction between production system and flock age for mammillary cap, early and late fusions. Cuticle cover ([Formula: see text]), was significantly higher in barn eggs (19.20), followed by free range (17.57), and cage eggs (15.99). Completeness of cuticle cover was significantly higher in eggs from the 44 week old flock than for 64 week and 73 week old flocks. For eggshells with cuticle intact, there was a significant main effect of both production system and flock age, and significant interaction between the two, for shell reflectivity, L*a*b* values and amount of PP IX. For PP IX, when this difference was calculated for the cuticle alone, there were no statistically significant differences. In 1 g of shell with and without cuticle, there was more PP IX in cage eggs (9.49 × 10 -8 , 7.90 × 10 -8  mM) followed by free range (8.24 × 10 -8 , 6.90 × 10 -8  mM), and barn eggs (8.64 × 10 -8 , 7.28 × 10 -8  mM). Similar trends were recorded for the amount of PP IX in 1 g of cuticle, but the difference was not statistically significant. The amount of PP IX decreased significantly with increasing flock age. Comparing the cage and barn production systems at 68 week of flock age, there was no difference for the amount of PP IX in shell with or without cuticle, or in the cuticle alone. Eggs from the cage production system were darker in color

Ostrich eggshell as calcium source for the synthesis of hydroxyapatite and hydroxyapatite partially substituted with zinc

International Nuclear Information System (INIS)

Ferreira, J.R.M.; Louro, L.H.L.; Costa, A.M.; Silva, M.H. Prado da; Campos, J.B. de

2016-01-01

In the present study, hydroxyapatite and Zn-substituted hydroxyapatite powders were synthesized using ostrich eggshell as a calcium source. The samples were analyzed by scanning electron microscopy with field emission gun, and X-ray diffraction (XRD) to identify the present phases, and X-ray fluorescence spectroscopy for quantitative chemical analysis of the synthesized and heat treated powders. The Fourier transform infrared spectroscopy technique was used before and after heat treatments at 700, 900 and 1100 °C in order to identify the functional groups present, as an additional technique to the XRD analysis. The results presented in this study represent a promising method for synthesis of hydroxyapatite and hydroxyapatite partially substituted with zinc, since the results showed no undesirable phases or impurities in the produced powders. It was observed that Zn-substituted hydroxyapatite showed higher thermal stability, when compared to pure hydroxyapatite. (author)

Ostrich eggshell as calcium source for the synthesis of hydroxyapatite and hydroxyapatite partially substituted with zinc

Energy Technology Data Exchange (ETDEWEB)

Ferreira, J.R.M.; Louro, L.H.L.; Costa, A.M.; Silva, M.H. Prado da [Instituto Militar de Engenharia (IME), Rio de Janeiro, RJ (Brazil); Campos, J.B. de, E-mail: josericardo@r-crio.com, E-mail: louro@ime.eb.br, E-mail: andrea@r-crio.com, E-mail: brantjose@gmail.com, E-mail: marceloprado@ime.eb.br [Universidade do Estado do Rio de Janeiro (UERJ), Rio de Janeiro, RJ (Brazil)

2016-10-15

In the present study, hydroxyapatite and Zn-substituted hydroxyapatite powders were synthesized using ostrich eggshell as a calcium source. The samples were analyzed by scanning electron microscopy with field emission gun, and X-ray diffraction (XRD) to identify the present phases, and X-ray fluorescence spectroscopy for quantitative chemical analysis of the synthesized and heat treated powders. The Fourier transform infrared spectroscopy technique was used before and after heat treatments at 700, 900 and 1100 °C in order to identify the functional groups present, as an additional technique to the XRD analysis. The results presented in this study represent a promising method for synthesis of hydroxyapatite and hydroxyapatite partially substituted with zinc, since the results showed no undesirable phases or impurities in the produced powders. It was observed that Zn-substituted hydroxyapatite showed higher thermal stability, when compared to pure hydroxyapatite. (author)

Persistent organic Pollutants (POPs) in the Greenland environment - Long-term temporal changes and effects on eggs of a bird of prey

DEFF Research Database (Denmark)

Sørensen, Peter Borgen; Vorkamp, Katrin; Thomsen, Marianne

The project studied the long-term time trend of brominated flame retardants, polychlorinated biphenyls (PCBs) and organochlorine pesticides in peregrine falcon (Falco peregrinus) eggs. Furthermore, possible effects of the contamination on the eggshell thickness were investigated using multivariate...

Numerical modeling of heat transfer and pasteurizing value during thermal processing of intact egg.

Science.gov (United States)

Abbasnezhad, Behzad; Hamdami, Nasser; Monteau, Jean-Yves; Vatankhah, Hamed

2016-01-01

Thermal Pasteurization of Eggs, as a widely used nutritive food, has been simulated. A three-dimensional numerical model, computational fluid dynamics codes of heat transfer equations using heat natural convection, and conduction mechanisms, based on finite element method, was developed to study the effect of air cell size and eggshell thickness. The model, confirmed by comparing experimental and numerical results, was able to predict the temperature profiles, the slowest heating zone, and the required heating time during pasteurization of intact eggs. The results showed that the air cell acted as a heat insulator. Increasing the air cell volume resulted in decreasing of the heat transfer rate, and the increasing the required time of pasteurization (up to 14%). The findings show that the effect on thermal pasteurization of the eggshell thickness was not considerable in comparison to the air cell volume.

Improving friction stir welding of blanks of different thicknesses

Energy Technology Data Exchange (ETDEWEB)

Fratini, L. [Dipartimento di Tecnologia Meccanica, Produzione e Ingegneria Gestionale, Universita di Palermo, Viale delle Scienze, 90128 Palermo (Italy)], E-mail: abaqus@dtpm.unipa.it; Buffa, G. [Dipartimento di Tecnologia Meccanica, Produzione e Ingegneria Gestionale, Universita di Palermo, Viale delle Scienze, 90128 Palermo (Italy); Shivpuri, R. [Ohio State University, Department of Industrial, Welding and Systems Engineering, 1971 Neil Avenue, 210 Baker Systems, Columbus, Ohio 43210 (United States)

2007-06-25

Friction stir welding (FSW) appears to be a promising process even in the welding of blanks of different thicknesses. Actually, such particular tailor welded blanks (TWBs) are usually characterized by a reduction in ductility due to the utilized fusion welding process. In this paper the authors, starting from a preliminary feasibility study, investigate the possibility to improve the mechanical performances of friction stir welded blanks of aluminum alloy with different thicknesses. Both experiments and a FE analyses are developed for a few case studies with different thickness ratios between the blanks. The numerical investigations are performed with the aim to highlight the material temperature distribution during the process in order to determine process conditions for which an almost symmetric thermal flow is obtained in the two blanks of the joint. In this way, a few simple process design rules are derived and verified through experiments. In particular a thickness ratio up to 2 was considered and a joint resistance of about the 80% of the parent material ultimate tensile strength was observed.

Improving friction stir welding of blanks of different thicknesses

International Nuclear Information System (INIS)

Fratini, L.; Buffa, G.; Shivpuri, R.

2007-01-01

Friction stir welding (FSW) appears to be a promising process even in the welding of blanks of different thicknesses. Actually, such particular tailor welded blanks (TWBs) are usually characterized by a reduction in ductility due to the utilized fusion welding process. In this paper the authors, starting from a preliminary feasibility study, investigate the possibility to improve the mechanical performances of friction stir welded blanks of aluminum alloy with different thicknesses. Both experiments and a FE analyses are developed for a few case studies with different thickness ratios between the blanks. The numerical investigations are performed with the aim to highlight the material temperature distribution during the process in order to determine process conditions for which an almost symmetric thermal flow is obtained in the two blanks of the joint. In this way, a few simple process design rules are derived and verified through experiments. In particular a thickness ratio up to 2 was considered and a joint resistance of about the 80% of the parent material ultimate tensile strength was observed

The influence of tongue strength on oral viscosity discrimination acuity.

Science.gov (United States)

Steele, Catriona M

2018-06-01

The ability to generate tongue pressures is widely considered to be critical for liquid bolus propulsion in swallowing. It has been proposed that the application of tongue pressure may also serve the function of collecting sensory information regarding bolus viscosity (resistance to flow). In this study, we explored the impact of age-related reductions in tongue strength on oral viscosity discrimination acuity. The experiment employed a triangle test discrimination protocol with an array of xanthan-gum thickened liquids in the mildly to moderately thick consistency range. A sample of 346 healthy volunteers was recruited, with age ranging from 12 to 86 (164 men, 182 women). On average, participants were able to detect a 0.29-fold increase in xanthan-gum concentration, corresponding to a 0.5-fold increase in viscosity at 50/s. Despite having significantly reduced tongue strength on maximum isometric tongue-palate pressure tasks, and regardless of sex, older participants in this study showed no reductions in viscosity discrimination acuity. In this article, the relationship between tongue strength and the ability to discriminate small differences in liquid viscosity during oral processing is explored. Given that tongue strength declines with age in healthy adults and is also reduced in individuals with dysphagia, it is interesting to determine whether reduced tongue strength might contribute to difficulties in evaluating liquid viscosity during the oral stage of swallowing. Using an array of mildly to moderately thick xanthan-gum thickened liquids, this experiment failed to find any evidence that reductions in tongue strength influence oral viscosity discrimination acuity. © 2017 Wiley Periodicals, Inc.

Eggshell membrane: A possible new natural therapeutic for joint and connective tissue disorders. Results from two open-label human clinical studies

Directory of Open Access Journals (Sweden)

Kevin J Ruff

2009-05-01

Full Text Available Kevin J Ruff1, Dale P DeVore2, Michael D Leu3, Mark A Robinson41ESM Technologies, LLC, Carthage, MO, USA; 2Membrell, LLC, Carthage, MO, USA; 3Private Practice, Jenks, OK, USA; 4Robinson Family Health Center, Carthage, MO, USABackground: Natural Eggshell Membrane (NEM® is a novel dietary supplement that contains naturally occurring glycosaminoglycans and proteins essential for maintaining healthy joint and connective tissues. Two single center, open-label human clinical studies were conducted to evaluate the efficacy and safety of NEM® as a treatment for pain and inflexibility associated with joint and connective tissue disorders. Methods: Eleven (single-arm trial and 28 (double-arm trial patients received oral NEM® 500 mg once daily for four weeks. The primary outcome measure was to evaluate the change in general pain associated with the treatment joints/areas (both studies. In the single-arm trial, range of motion (ROM and related ROM-associated pain was also evaluated. The primary treatment response endpoints were at seven and 30 days. Both clinical assessments were performed on the intent-to-treat (ITT population within each study.Results: Single-arm trial: Supplementation with NEM® produced a significant treatment response at seven days for flexibility (27.8% increase; P = 0.038 and at 30 days for general pain (72.5% reduction; P = 0.007, flexibility (43.7% increase; P = 0.006, and ROM-associated pain (75.9% reduction; P = 0.021. Double-arm trial: Supplementation with NEM® produced a significant treatment response for pain at seven days for both treatment arms (X: 18.4% reduction; P = 0.021. Y: 31.3% reduction; P = 0.014. There was no clinically meaningful difference between treatment arms at seven days, so the Y arm crossed over to the X formulation for the remainder of the study. The significant treatment response continued through 30 days for pain (30.2% reduction; P = 0.0001. There were no adverse events reported during either

Persistent organic Pollutants (POPs) in the Greenland environment - Long-term temporal changes and effects on eggs of a bird of prey

DEFF Research Database (Denmark)

Sørensen, P. B.; Vorkamp, K.; Thomsen, M.

The project studied the long-term time trend of brominated flame retardants, poly-chlorinated biphenyls (PCBs) and organochlorine pesticides in peregrine falcon (Falco peregrinus) eggs. Furthermore, possible effects of the contamination on the eggshell thickness were investigated using multivariate...

(p,γ) resonance strengths in the s-d shell

International Nuclear Information System (INIS)

Paine, B.M.; Sargood, D.G.

1979-01-01

The strengths of selected resonances in the energy range 0.5-2.0 MeV in the (p,γ) reactions on 26 Mg, 30 Si, 34 S, 37 C1, 39 K and 40 Ca have been found relative to the 632 and 992 keV resonances in 27 A1(p,γ) 28 Si by relative yield measurements. Absolute measurements were conducted on the selected resonances in 27 A1(p,γ) 28 Si and 30 Si(p,γ) 31 p by semi-thick target and thin target techniques with the target thickness, needed for the latter technique, found by Rutherford backscattering of protons. Absolute strengths for all of the resonances treated, together with one from each of 23 Na, 31 p and 35 C1, reported in a previous paper, were deduced by normalizing to the absolute measurements on the 27 A1(p,γ) 28 Si resonances

Near-ideal strength in metal nanotubes revealed by atomistic simulations

Energy Technology Data Exchange (ETDEWEB)

Sun, Mingfei; Xiao, Fei [Department of Materials Science, Fudan University, 220 Handan Road, Shanghai 200433 (China); Deng, Chuang, E-mail: dengc@ad.umanitoba.ca [Department of Mechanical and Manufacturing Engineering, The University of Manitoba, 15Gillson Street, Winnipeg, Manitoba R3T 5V6 (Canada)

2013-12-02

Here we report extraordinary mechanical properties revealed by atomistic simulations in metal nanotubes with hollow interior that have been long overlooked. Particularly, the yield strength in [1 1 1] Au nanotubes is found to be up to 60% higher than the corresponding solid Au nanowire, which approaches the theoretical ideal strength in Au. Furthermore, a remarkable transition from sharp to smooth yielding is observed in Au nanotubes with decreasing wall thickness. The ultrahigh tensile strength in [1 1 1] Au nanotube might originate from the repulsive image force exerted by the interior surface against dislocation nucleation from the outer surface.

The influence of annealing temperature on the strength of TRISO coated particles

Energy Technology Data Exchange (ETDEWEB)

Rooyen, I.J. van, E-mail: Isabel.vanrooyen@pbmr.co.z [Pebble Bed Modular Reactor (Pty) Ltd., 1279 Mike Crawford Avenue, Centurion (South Africa); Department of Physics, Nelson Mandela Metropolitan University, Port Elizabeth (South Africa); Neethling, J.H. [Department of Physics, Nelson Mandela Metropolitan University, Port Elizabeth (South Africa); Rooyen, P.M. van [Pebble Bed Modular Reactor (Pty) Ltd., 1279 Mike Crawford Avenue, Centurion (South Africa)

2010-07-31

The integrity of the Pebble Bed Modular Reactor (PBMR) fuel, and specifically the SiC layer system of the Tristructural Isotropic (TRISO) coated particle (CP), namely inner pyrolytic carbon, silicon carbide and outer pyrolytic carbon (I-PyC-SiC-O-PyC), determines the containment of fission products. The PBMR fuel consists of TRISO coated particles (CPs) embedded in a graphite matrix. One of the characterization techniques investigated by PBMR is the determination of strength of CPs. It is a well known metallurgical fact that temperature, amongst many other parameters, may influence the strength of a material. A recently developed method for measuring the strength of the TRISO coated particles was used and is briefly described in this article. The advantages of this method are demonstrated by the comparison of strength measurements of five experimental PBMR CP batches as a function of annealing temperature. Significant modification of strength after annealing was measured with increased temperature within the range 1000-2100 {sup o}C. The interesting feature of decreasing standard deviation of the strength with increasing temperature will also be discussed with a possible explanation. A significant difference in coated particle strength is also demonstrated for two CP batches with layer thickness on the extremities of the SiC layer thickness specification. The effect of long duration annealing on these strength values will also be demonstrated by comparing results from 1 h to 100 h annealing periods of coated particles at a temperature of 1600 {sup o}C.

Effect of coating thickness on interfacial shear behavior of zirconia-coated sapphire fibers in a polycrystalline alumina matrix

International Nuclear Information System (INIS)

Hellmann, J.R.; Chou, Y.S.

1995-01-01

The effect of zirconia (ZrO 2 ) interfacial coatings on the interfacial shear behavior in sapphire reinforced alumina was examined in this study. Zirconia coatings of thicknesses ranging from 0.15 to 1.45 μm were applied to single crystal sapphire (Saphikon) fibers using a particulate loaded sol dipping technique. After calcining at 1,100 C in air, the coated fibers were incorporated into a polycrystalline alumina matrix via hot pressing. Interfacial shear strength and sliding behavior of the coated fibers was examined using thin-slice indentation fiber pushout and pushback techniques. In all cases, debonding and sliding occurred at the interface between the fibers and the coating. The coatings exhibited a dense microstructure and led to a higher interfacial shear strength (> 240 MPa) and interfacial sliding stress (> 75 MPa) relative to previous studies on the effect of a porous interphase on interfacial properties. The interfacial shear strength decreased with increasing fiber coating thickness (from 389 ± 59 to 241 ± 43 MPa for 0.15 to 1.45 microm thick coatings, respectively). Sliding behavior exhibited load modulation with increasing displacement during fiber sliding which is characteristic of fiber roughness-induced stick-slip. The high interfacial shear strengths and sliding stresses measured in this study, as well as the potentially strength degrading surface reconstruction observed on the coated fibers after hot pressing and heat treatment, indicate that dense zirconia coatings are not suitable candidates for optimizing composite toughness and strength in the sapphire fiber reinforced alumina system

EFFECT OF THE DIETARY PELLET:MEAL RATIO ON THE PRODUCTIVE PERFORMANCE OF LAYING HENS

Directory of Open Access Journals (Sweden)

Luis Armando Sarmiento-Franco

2009-07-01

Full Text Available The effect of dietary pellet:meal ratio on the performance of laying hens was evaluated using 60 Plymouth Barred Rock 30 week old hens. Hens were distributed at random to three treatments: 100:0, 75:25 and 50:50% of pellet:meal ratio in the diet along 49 days, with 20 replicates each. Final body weight of hens, polar and ecuatorial diameters of the egg, eggshell weight, eggshell thickness, and yolk colour were not different between treatments (p>0.05. However, egg production, egg weight, egg mass, food consumption, food conversion and production cost were affected by treatments (p

Trochanteric Soft Tissue Thickness and Hip Fracture in Older Men

Science.gov (United States)

Nielson, Carrie M.; Bouxsein, Mary L.; Freitas, Sinara S.; Ensrud, Kristine E.; Orwoll, Eric S.

2009-01-01

Background: Greater thickness of the tissue extending laterally from the greater trochanter has been associated with a lower risk of hip fracture in women. The effect of trochanteric soft tissue thickness on the risk of incident hip fracture has not been evaluated in men. Methods: We measured trochanteric soft tissue thickness by dual-energy x-ray absorptiometry for all incident hip fracture cases (n = 70) and 222 randomly selected noncases in older men (≥65 yr) enrolled in the Osteoporotic Fractures in Men (MrOS) Study. Differences in tissue thickness between cases and controls were examined. Changes in fall force and factor-of-risk (the ratio of force from a sideways fall to femoral bone strength) associated with tissue thickness were determined. The relative risk for incident hip fracture per sd decrease in tissue thickness was calculated. Results: Mean trochanteric soft tissue thickness did not differ significantly between cases and noncases (29.1 ± 11.9 vs 31.0 ± 11.5 mm; P = 0.2). Although increased tissue thickness reduced both the estimates of fall force and the factor-of-risk, tissue thickness was not associated with the risk of hip fracture (age- and bone mineral density-adjusted relative risk per sd decrease in tissue thickness = 0.90; 95% confidence interval, 0.70–1.16). Conclusions: In this study of elderly community-dwelling men, we found no significant association between trochanteric soft tissue thickness and incident hip fracture. Trochanteric soft tissue thickness in these men was less than previously reported in older women and may explain the difference between these results and those reported in women. PMID:19017753

Compression of thick laminated composite beams with initial impact-like damage

Science.gov (United States)

Breivik, N. L.; Guerdal, Z.; Griffin, O. H., Jr.

1992-01-01

While the study of compression after impact of laminated composites has been under consideration for many years, the complexity of the damage initiated by low velocity impact has not lent itself to simple predictive models for compression strength. The damage modes due to non-penetrating, low velocity impact by large diameter objects can be simulated using quasi-static three-point bending. The resulting damage modes are less coupled and more easily characterized than actual impact damage modes. This study includes the compression testing of specimens with well documented initial damage states obtained from three-point bend testing. Compression strengths and failure modes were obtained for quasi-isotropic stacking sequences from 0.24 to 1.1 inches thick with both grouped and interspersed ply stacking. Initial damage prior to compression testing was divided into four classifications based on the type, extent, and location of the damage. These classifications are multiple through-thickness delaminations, isolated delamination, damage near the surface, and matrix cracks. Specimens from each classification were compared to specimens tested without initial damage in order to determine the effects of the initial damage on the final compression strength and failure modes. A finite element analysis was used to aid in the understanding and explanation of the experimental results.

Organic biowastes blend selection for composting industrial eggshell by-product: experimental and statistical mixture design.

Science.gov (United States)

Soares, Micaela A R; Andrade, Sandra R; Martins, Rui C; Quina, Margarida J; Quinta-Ferreira, Rosa M

2012-01-01

Composting is one of the technologies recommended for pre-treating industrial eggshells (ES) before its application in soils, for calcium recycling. However, due to the high inorganic content of ES, a mixture of biodegradable materials is required to assure a successful procedure. In this study, an adequate organic blend composition containing potato peel (PP), grass clippings (GC) and wheat straw (WS) was determined by applying the simplex-centroid mixture design method to achieve a desired moisture content, carbon: nitrogen ratio and free air space for effective composting of ES. A blend of 56% PP, 37% GC and 7% WS was selected and tested in a self heating reactor, where 10% (w/w) of ES was incorporated. After 29 days of reactor operation, a dry matter reduction of 46% was achieved and thermophilic temperatures were maintained during 15 days, indicating that the blend selected by statistical approach was adequate for composting of ES.

Polyelectrolyte multilayer assembly as a function of pH and ionic strength using the polysaccharides chitosan and heparin.

Science.gov (United States)

Boddohi, Soheil; Killingsworth, Christopher E; Kipper, Matt J

2008-07-01

The goal of this work is to explore the effects of solution ionic strength and pH on polyelectrolyte multilayer (PEM) assembly, using biologically derived polysaccharides as the polyelectrolytes. We used the layer-by-layer (LBL) technique to assemble PEM of the polysaccharides heparin (a strong polyanion) and chitosan (a weak polycation) and characterized the sensitivity of the PEM composition and layer thickness to changes in processing parameters. Fourier-transform surface plasmon resonance (FT-SPR) and spectroscopic ellipsometry provided in situ and ex situ measurements of the PEM thickness, respectively. Vibrational spectroscopy and X-ray photoelectron spectroscopy (XPS) provided details of the chemistry (i.e., composition, electrostatic interactions) of the PEM. We found that when PEM were assembled from 0.2 M buffer, the PEM thickness could be increased from less than 2 nm per bilayer to greater than 4 nm per bilayer by changing the solution pH; higher and lower ionic strength buffer solutions resulted in narrower ranges of accessible thickness. Molar composition of the PEM was not very sensitive to solution pH or ionic strength, but pH did affect the interactions between the sulfonates in heparin and amines in chitosan when PEM were assembled from 0.2 M buffer. Changes in the PEM thickness with pH and ionic strength can be interpreted through descriptions of the charge density and conformation of the polyelectrolyte chains in solution.

Effects of Zeolite (Clinoptelolite on Performance Characteristics of

Directory of Open Access Journals (Sweden)

A Hassan Abadim

2011-12-01

Full Text Available A 70-days experiment was conducted to investigate the effects of natural zeolite (clinoptelolite on the performance of commercial laying hens. 288 Hy-Line W36 strain laying hens (50 weeks old were allotted to 6 dietary treatments including basal diet as control and basal diet supplemented with 1, 2, 3, 4 and 5% zeolite that were fed ad -libitum throughout the experiment. Experimental diets for the 6 treatments were prepared to be iso-caloric and iso-nitrogenous. A completely randomized design with six treatments, eight replicates of six birds per replicate was used at this experiment. Daily feed intake (DFI, feed conversion ratio (FCR, egg production, egg weight, egg white quality, eggshell quality (thickness and percentage and body weight changes were measured during the experiment. Results of this experiment showed that DFI, FCR, egg production and egg abnormality were not significantly (P>0.05 affected by zeolite supplementation. Zeolite supplementation significantly increased egg weight, eggshell thickness and live body weight gain of the hens. Dietary zeolite significantly decreased haugh unit of the eggs. In conclusion, natural zeolite significantly improved egg weight and eggshell quality, decreased haugh unit and live weight gain, and had no significant effects on other parameters.

Topology of interaction between titin and myosin thick filaments.

Science.gov (United States)

Kellermayer, Miklós; Sziklai, Dominik; Papp, Zsombor; Decker, Brennan; Lakatos, Eszter; Mártonfalvi, Zsolt

2018-05-05

Titin is a giant protein spanning between the Z- and M-lines of the sarcomere. In the A-band titin is associated with the myosin thick filament. It has been speculated that titin may serve as a blueprint for thick-filament formation due to the super-repeat structure of its A-band domains. Accordingly, titin might provide a template that determines the length and structural periodicity of the thick filament. Here we tested the titin ruler hypothesis by mixing titin and myosin at in situ stoichiometric ratios (300 myosins per 12 titins) in buffers of different ionic strength (KCl concentration range 100-300 mM). The topology of the filamentous complexes was investigated with atomic force microscopy. We found that the samples contained distinct, segregated populations of titin molecules and myosin thick filaments. We were unable to identify complexes in which myosin molecules were regularly associated to either mono- or oligomeric titin in either relaxed or stretched states of the titin filaments. Thus, the electrostatically driven self-association is stronger in both myosin and titin than their binding to each other, and it is unlikely that titin functions as a geometrical template for thick-filament formation. However, when allowed to equilibrate configurationally, long myosin thick filaments appeared with titin oligomers attached to their surface. The titin meshwork formed on the thick-filament surface may play a role in controlling thick-filament length by regulating the structural dynamics of myosin molecules and placing a mechanical limit on the filament length. Copyright © 2018 Elsevier Inc. All rights reserved.

Effects of rework on adhesion of Pb-In soldered gold thick films

International Nuclear Information System (INIS)

Gehman, R.W.; Becka, G.A.; Losure, J.A.

1982-02-01

The feasibility of repeatedly reworking Pb-In soldered joints on gold thick films was evaluated. Nailhead adhesion tests on soldered thick films typically resulted in failure within the bulk solder (50 In-50 Pb). Average strengths increased with each rework, and the failure mode changed. An increase in metalization lift-off occurred with successive reworks. An investigation was initiated to determine why these changes occurred. Based on this work, the thick film adhesion to the substrate appeared to be lowered by indium reduction of cadmium oxide and by formation of a weak, brittle intermetallic compound, Au 9 In 4 . It was concluded that two solder reworks could be conducted without significant amounts of metallization lift-off during nailhead testing

[Preliminary analysis about influence of porcelain thickness on interfacial crack of PFM].

Science.gov (United States)

Zhu, Ziyuan; Zhang, Baowei; Zhang, Xiuyin; Xu, Kan; Fang, Ruhua; Wang, Dongmei

2002-01-01

This study was about the influence of porcelain thickness on crack at interface. The effect of porcelain thickness on the flaw at the interface between porcelain and metal was studied in three groups with porcelain thickness of 0.5 mm, 1.5 mm and 2.5 mm (metal thickness of 0.5 mm) by means of moire interferometre and interfacial fracture mechanics. The parameter Jc was compared among the three groups and the growing of the flaw was observed. Jc and the extreme strength of group with porcelain thickness of 0.5 mm (2.813 N/m and 9.979 N) were lower than those of the groups with porcelain thickness of 1.5 mm and 2.5 mm (5.395 N/m, 19.134 N and 5.429 N/m, 19.256 N). Flaws extend along the interface in the groups with porcelain thickness of 1.5 mm and 0.5 mm. (1) Fracture resistance of the interface in the groups with porcelain thickness of 1.5 mm and 2.5 mm is similar and it decreases in the group with 0.5 mm thick porcelain. (2) When porcelain is 1.5 mm or 0.5 mm thick, flaws will extend along the interface. When porcelain is 2.5 mm thick, flaws will extend into the porcelain layer.

root extract on egg production

African Journals Online (AJOL)

2013-07-30

Jul 30, 2013 ... using a shell strength device with a spiral pressure system (Fujihara, ... spectrophotometer by the improved ABTS•+ method, as described by ..... no advantage of this attribute in characterizing eggshell colour (Li et al., 2006).

MICROSTRUCTURE AND MECHANICAL STRENGTH OF SURFACE ODS TREATED ZIRCALOY-4 SHEET USING LASER BEAM SCANNING

Directory of Open Access Journals (Sweden)

HYUN-GIL KIM

2014-08-01

Full Text Available The surface modification of engineering materials by laser beam scanning (LBS allows the improvement of properties in terms of reduced wear, increased corrosion resistance, and better strength. In this study, the laser beam scan method was applied to produce an oxide dispersion strengthened (ODS structure on a zirconium metal surface. A recrystallized Zircaloy-4 alloy sheet with a thickness of 2 mm, and Y2O3 particles of 10 μm were selected for ODS treatment using LBS. Through the LBS method, the Y2O3 particles were dispersed in the Zircaloy-4 sheet surface at a thickness of 0.4 mm, which was about 20% when compared to the initial sheet thickness. The mean size of the dispersive particles was 20 nm, and the yield strength of the ODS treated plate at 500°C was increased more than 65 % when compared to the initial state. This strength increase was caused by dispersive Y2O3 particles in the matrix and the martensite transformation of Zircaloy-4 matrix by the LBS.

Ostrich eggshell as calcium source for the synthesis of hydroxyapatite and hydroxyapatite partially substituted with zinc

Directory of Open Access Journals (Sweden)

J. R. M. Ferreira

Full Text Available Abstract In the present study, hydroxyapatite and Zn-substituted hydroxyapatite powders were synthesized using ostrich eggshell as a calcium source. The samples were analyzed by scanning electron microscopy with field emission gun, and X-ray diffraction (XRD to identify the present phases, and X-ray fluorescence spectroscopy for quantitative chemical analysis of the synthesized and heat treated powders. The Fourier transform infrared spectroscopy technique was used before and after heat treatments at 700, 900 and 1100 °C in order to identify the functional groups present, as an additional technique to the XRD analysis. The results presented in this study represent a promising method for synthesis of hydroxyapatite and hydroxyapatite partially substituted with zinc, since the results showed no undesirable phases or impurities in the produced powders. It was observed that Zn-substituted hydroxyapatite showed higher thermal stability, when compared to pure hydroxyapatite.

Economical Fabrication of Thick-Section Ceramic Matrix Composites

Science.gov (United States)

Babcock, Jason; Ramachandran, Gautham; Williams, Brian; Benander, Robert

2010-01-01

A method was developed for producing thick-section [>2 in. (approx.5 cm)], continuous fiber-reinforced ceramic matrix composites (CMCs). Ultramet-modified fiber interface coating and melt infiltration processing, developed previously for thin-section components, were used for the fabrication of CMCs that were an order of magnitude greater in thickness [up to 2.5 in. (approx.6.4 cm)]. Melt processing first involves infiltration of a fiber preform with the desired interface coating, and then with carbon to partially densify the preform. A molten refractory metal is then infiltrated and reacts with the excess carbon to form the carbide matrix without damaging the fiber reinforcement. Infiltration occurs from the inside out as the molten metal fills virtually all the available void space. Densification to thick-section components required modification of the conventional process conditions, and the means by which the large amount of molten metal is introduced into the fiber preform. Modification of the low-temperature, ultraviolet-enhanced chemical vapor deposition process used to apply interface coatings to the fiber preform was also required to accommodate the high preform thickness. The thick-section CMC processing developed in this work proved to be invaluable for component development, fabrication, and testing in two complementary efforts. In a project for the Army, involving SiC/SiC blisk development, nominally 0.8 in. thick x 8 in. diameter (approx. 2 cm thick x 20 cm diameter) components were successfully infiltrated. Blisk hubs were machined using diamond-embedded cutting tools and successfully spin-tested. Good ply uniformity and extremely low residual porosity (41 ksi (approx. 283 MPa) flexural strength.

Organochlorine residues and shell thicknesses in eggs of the clapper rail, common gallinule, purple gallinule, and limpkin (class Aves), eastern and southern United States, 1972-74.

Science.gov (United States)

Klaas, E E; Ohlendorf, H M; Cromartie, E

1980-12-01

Organochlorine residues and shell thicknesses were surveyed in eggs of the clapper rail (Rallus longirostris), purple gallinule (Porphyrula martinica), common gallinule (Gallinula chloropas), and limpkin (Aramus guarauna) from the eastern and southern United States. Clapper rail eggs were collected during 1972-73 in New Jersey, Virginia, and South Carolina. During 1973-74, gallinule eggs were collected in Florida, South Carolina, and Louisiana, and limpkin eggs were collected in Florida. Egg contents were analyzed for residues of organochlorine pesticides, including DDT, TDE, DDE, dieldrin, mirex, heptachlor epoxide, oxychlordane, cis-chlordane (and/or trans-nonachlor), cis-nonachlor, hexachlorobenzene (HCB), toxaphene, and endrin, and for polychlorinated biphenyls (PCBs). Shell thicknesses of recent eggs of these species were compared with archival eggs that had been collected before 1947. With the exception of the limpkin, the majority of eggs analyzed contained residues of p,p'-DDE and PCBs. Geometric means ranged from 0.10 ppm to 1.3 ppm. Small amounts (less than 1.0 ppm) of mirex, dieldrin, cis-chlordane (and/or trans-nonachlor), TDE, and DDT were detected in a few eggs. No evidence of eggshell thinning was found for any of the species studied. DDE residues in clapper rail eggs were higher in New Jersey and Virginia than in South Carolina.

Organochlorine residues and shell thickness in eggs of the clapper rail, common gallinule, purple gallinule, and limpkin (Class Aves), eastern and southern United States, 1972-74

Science.gov (United States)

Klaas, E.E.; Ohlendorf, H.M.; Cromartie, E.

1980-01-01

Organochlorine residues and shell thicknesses were surveyed in eggs of the clapper rail (Rallus longirostris), purple gallinule (Porphyrula martinica), common gallinule (Gallinula chloropas), and limpkin (Aramus guarauna) from the eastern and southern United States. Clapper rail eggs were collected during 1972-73 in New Jersey, Virginia, and South Carolina. During 1973-74, gallinule eggs were collected in Florida, South Carolina, and Louisiana, and limpkin eggs were collected in Florida. Egg contents were analyzed for residues of organochlorine pesticides, including DDT, TDE, DDE, dieldrin, mirex, heptachlor epoxide, oxychlordane, cis-chlordane (and/or trans-nonachlor), cis-nonachlor, hexachlorobenzene (HCB), toxaphene, and endrin, and for polychlorinated biphenyls (PCBs). Shell thicknesses of recent eggs of these species were compared with archival eggs that had been collected before 1947. With the exception of the limpkin, the majority of eggs analyzed contained residues of p,p'-DDE and PCBs. Geometric means ranged from 0.10 ppm to 1.3 ppm. Small amounts (less than 1.0 ppm) of mirex, dieldrin, cis-chlordane (and/or trans-nonachlor), TDE, and DDT were detected in a few eggs. No evidence of eggshell thinning was found for any of the species studied. DDE residues in clapper rail eggs were higher in New Jersey and Virginia than in South Carolina.

Quality traits of eggs from autosexing Easter eggers

Directory of Open Access Journals (Sweden)

H. Lukanov

2016-09-01

Full Text Available Abstract. The main egg quality traits were investigated in two autosexing F1 Easter egger crosses. Partridge Araucana roosters were used as carriers of the eggshell biliverdin pigmentation gene. Maternal forms used for obtaining the two experimental crosses were high-producing layer hens carrying the sex-linked S and B genes. Experimental groups comprised F1 crosses of partridge Araucana roosters with white mutational Rhode Island hens or hens with barred colour mutation. The aim of the study was to investigated the quality traits of blue-green eggs produced by autosexing hens. The egg quality was evaluated at 38 weeks of age. Studied traits comprised egg weight (g, shape index, albumen index (AI, Haugh units (HU, yolk index (YI, yolk colour (Roche scale, 2 2 percentages of albumen, yolk and eggshell (%, eggshell surface (cm , eggshell density (mg/cm , average eggshell thickness (µm and eggshell colour. The group W was outlined with the highest egg weight – 61.03±0.47 g, and group A – with the lowest (50.91±0.32 g. The albumen and yolk quality was the best in group A, where albumen index was 0.075±0.002, Haugh units – 76.53±0.8 and yolk index – 0.491±0.009. The analysis of eggshell colour showed that eggs of group A were with the highest lightness (L* value (73.60±0.77, whereas eggs of groups W and AW had egg lightness of 60.45±0.53 and 61.11±0.55 (p<0.001 respectively. The shell colour index (SCI demonstrated a certain overlap of values in eggs with protoporphyrin and biliverdin taints. After introduction of a correction coefficient and recalculation of SCI*, the values of green eggs assumed a negative sign and could be distinguished from brown eggs.

Sunflower meal in commercial layer diets formulated on total and digestible amino acids basis

Directory of Open Access Journals (Sweden)

EM Casartelli

2006-09-01

Full Text Available An experiment was conduced to evaluate the inclusion of sunflower meal (SBM in commercial layer diets formulated on total or digestible amino acids basis. One hundred forty-four 41-week-old Lohmann LSL layers were distributed in a completely randomized experimental design in a 2 x 4 factorial arrangement with three replications of six birds each. Treatments consisted of a combination of four SBM inclusion levels SBM(0%, 4%, 8%, and 12% and feed formulation according two amino acid recommendations (total or digestible. The experimental period was divided into five periods of fourteen days. Performance parameters (egg production, feed intake, feed conversion, egg mass were evaluated for each period. In the last two days of each period, three eggs per replication were collected to evaluate egg quality (Haugh units, specific gravity, egg weight, eggshell thickness, and eggshell percentage. Hens fed on total amino acid recommendation presented the highest values for egg weight. Diets formulated on digestible amino acids basis showed an improvement in eggshell percentage and egg specific gravity. SBM addition in commercial layer diets did not influence performance; however, increasing SBM dietary levels SBM improved eggshell quality.

Impact cratering on porous targets in the strength regime

Science.gov (United States)

Nakamura, Akiko M.

2017-12-01

Cratering on small bodies is crucial for the collision cascade and also contributes to the ejection of dust particles into interplanetary space. A crater cavity forms against the mechanical strength of the surface, gravitational acceleration, or both. The formation of moderately sized craters that are sufficiently larger than the thickness of the regolith on small bodies, in which mechanical strength plays the dominant role rather than gravitational acceleration, is in the strength regime. The formation of microcraters on blocks on the surface is also within the strength regime. On the other hand, the formation of a crater of a size comparable to the thickness of the regolith is affected by both gravitational acceleration and cohesion between regolith particles. In this short review, we compile data from the literature pertaining to impact cratering experiments on porous targets, and summarize the ratio of spall diameter to pit diameter, the depth, diameter, and volume of the crater cavity, and the ratio of depth to diameter. Among targets with various porosities studied in the laboratory to date, based on conventional scaling laws (Holsapple and Schmidt, J. Geophys. Res., 87, 1849-1870, 1982) the cratering efficiency obtained for porous sedimentary rocks (Suzuki et al., J. Geophys. Res. 117, E08012, 2012) is intermediate. A comparison with microcraters formed on a glass target with impact velocities up to 14 km s-1 indicates a different dependence of cratering efficiency and depth-to-diameter ratio on impact velocity.

Impacts of Limestone Multi-particle Size on Production Performance, Egg Shell Quality, and Egg Quality in Laying Hens

Directory of Open Access Journals (Sweden)

X. Y. Guo

2012-06-01

Full Text Available This experiment was conducted to evaluate the effects of single or multi-particle size limestone on the egg shell quality, egg production, egg quality and feed intake in laying hens. A total of 280 laying hens (ISA brown were used in this 10-wk trial. Laying hens were randomly assigned to 4 treatments with 14 replications per treatment and 5 adjacent cages as a replication (hens were caged individually. The experimental treatments were: i L, basal diet+10% large particle limestone; ii LS1, basal diet+8% large particle limestone+2% small particle limestone; iii LS2, basal diet+6% large particle limestone+4% small particle limestone; iv S, basal diet+10% small particle limestone. The egg production was unaffected by dietary treatments. The egg weight in S treatment was lighter than other treatments (p<0.05. The egg specific gravity in S treatment was lower than other treatments (p<0.05. The eggshell strength and eggshell thickness in S treatment were decreased when compared with other dietary treatments (p<0.05. The laying hens in LS1 and LS2 treatment had a higher average feed intake than the other two treatments (p<0.05. Collectively, the dietary multi-particle size limestone supplementation could be as efficient as large particle size limestone.

Investigation on interlaminar shear strength properties of disc laser machined consolidated CF-PPS laminates

Directory of Open Access Journals (Sweden)

2011-03-01

Full Text Available In consequence of an increased interest in using endless carbon fibre reinforced thermoplastic composites (TPC, automated and highly productive processing technologies for cutting and trimming steps of consolidated materials are sought. In this paper, the influence on the thermal effect caused by laser cutting with respect to static strength properties of TPC based on a polyphenylene sulfide (PPS matrix is studied. For the cutting experiments, consolidated TPC laminates at varying thicknesses up to s = 3.1 mm and a disc laser emitting at a wavelength of λ = 1030 nm at a maximum output power of PL = 2 kW are used. For the first time, the resulting magnitude of the heat affected zone (HAZ at the cutting edge of the composite material is correlated with interlaminar shear strength tests. The results are compared to specimens prepared by milling and abrasive water jet cutting. Depending on the laminate thickness, the laser treated TPC samples show comparable properties to those of conventionally processed specimens. A reduced load bearing area, as a consequence of damaged fibre-matrix-adhesion due to laser impact, is identified as main factor for the reduction of interlaminar shear strengths for higher laminate thicknesses.

Environmental Assessment for Implementation of Expanded Bird-Aircraft Strike Hazard (BASH) Program for Moody Air Force Base and Private and Public Lands Surrounding Moody Air Force Base, Georgia

Science.gov (United States)

2003-09-01

values are not expected to be significantly impacted by any of the alternatives analyzed: soils , geology, minerals, water quality/quantity, flood...pesticides on eggshell thickness, rather than direct mortality events (GWF, 2003). The proposed action does not involve the destruction of nesting

EFFECTS OF EDGE COVERING ON TENSILE STRENGTH OF MDF

Directory of Open Access Journals (Sweden)

Yalçın ÖRS

1999-03-01

Full Text Available Dowels, 6, 8 and 10 mm ? diameters were bonded with PVAc adhesive on Medium Density Fiberboard (MDF. Edges were covered with 5, 8 and 12 mm beech wood materials, drilled 25 mm depth. Tensile strength measurments were made on the samples. The highest tensile strength value was given as 6 mm ? dowel and MDF covered with 8 mm thickness beech wood material (2.294 N/mm2, the lowest value was obtained with 10 mm ? dowel and with unprocessed MDF (1.314 N/mm2.

Improving Strength-Ductility Balance of High Strength Dual-Phase Steels by Addition of Vanadium

Science.gov (United States)

Gong, Yu; Hua, M.; Uusitalo, J.; DeArdo, A. J.

For galvanized or galvannealed steels to be commercially successful, they must exhibit several attributes: (i) easy and inexpensive processing in the hot mill, cold mill and on the coating line, (ii) high strength with good formability and spot weldability, and (iii) good corrosion resistance, especially after cold forming. For good corrosion resistance, the coating must have sufficient coverage, be of uniform thickness, and most importantly, the coating must survive the cold stamping or forming operation. The purpose of this paper is to present research aiming at improving the steel substrate, such that high strength can be obtained while maintaining good global formability (tensile ductility), local formability (sheared-edge ductility), and good spot weldability. It is well-known that the strength of DP steels is controlled by several factors, including the amount of martensite found in the final microstructure. Recent research has revealed that the amount of austenite formed during intercritical annealing can be strongly influenced by the annealing temperature and the pre-annealing conditions of the hot band (coiling temperature) and cold band (% cold reduction). Current experiments have explored the combination of pre-annealing conditions and four annealing practices to help define the best practice to optimize the strength-formability balance in these higher strength DP steels. The steels used in these experiments contained (i) low carbon content for good spot weldability, (ii) the hardenability additions Mo and Cr for strength, and (iii) V for grain refinement, precipitation hardening and temper resistance. When processed correctly, these steels exhibited UTS levels up to 1000MPa, total elongation to 25%, reduction in area to 45%, and Hole Expansion Ratios to 50%. The results of this program will be presented and discussed.

Pea proteins oral supplementation promotes muscle thickness gains during resistance training: a double-blind, randomized, Placebo-controlled clinical trial vs. Whey protein

OpenAIRE

Babault, Nicolas; Pa?zis, Christos; Deley, Ga?lle; Gu?rin-Deremaux, Laetitia; Saniez, Marie-H?l?ne; Lefranc-Millot, Catherine; Allaert, Fran?ois A

2015-01-01

Background The effects of protein supplementation on muscle thickness and strength seem largely dependent on its composition. The current study aimed at comparing the impact of an oral supplementation with vegetable Pea protein (NUTRALYS?) vs. Whey protein and Placebo on biceps brachii muscle thickness and strength after a 12-week resistance training program. Methods One hundred and sixty one males, aged 18 to 35?years were enrolled in the study and underwent 12?weeks of resistance training o...

Structure and corrosion behavior of sputter deposited cerium oxide based coatings with various thickness on Al 2024-T3 alloy substrates

Energy Technology Data Exchange (ETDEWEB)

Liu, Yuanyuan [College of Materials Science and Engineering, Chongqing University, Chongqing 400045 (China); Materials Research Center, Department of Materials Science and Engineering, Missouri University of Science and Technology, Rolla, MO 65409 (United States); Huang, Jiamu, E-mail: huangjiamu@cqu.edu.cn [College of Materials Science and Engineering, Chongqing University, Chongqing 400045 (China); Claypool, James B.; Castano, Carlos E. [Materials Research Center, Department of Materials Science and Engineering, Missouri University of Science and Technology, Rolla, MO 65409 (United States); O’Keefe, Matthew J., E-mail: mjokeefe@mst.edu [Materials Research Center, Department of Materials Science and Engineering, Missouri University of Science and Technology, Rolla, MO 65409 (United States)

2015-11-15

Highlights: • Crystalline CeO{sub 2} coatings are deposited on Al 2024-T3 alloys by magnetron sputtering. • The crystal size and internal stress both increased with the thickness of CeO{sub 2} coating. • The ∼210 nm thick coating has the highest adhesion strength to the Al alloy substrate. • The ∼900 nm thick coating increased the corrosion resistance two orders of magnitude. • CeO{sub 2} coatings provide good cathodic inhibition for Al alloys by acting as physical barriers. - Abstract: Cerium oxide based coatings from ∼100 to ∼1400 nm in thickness were deposited onto Al 2024-T3 alloy substrates by magnetron sputtering of a 99.99% pure CeO{sub 2} target. The crystallite size of CeO{sub 2} coatings increased from 15 nm to 46 nm as the coating thickness increased from ∼100 nm to ∼1400 nm. The inhomogeneous lattice strain increased from 0.36% to 0.91% for the ∼100 nm to ∼900 nm thick coatings and slightly decreased to 0.89% for the ∼1400 nm thick coating. The highest adhesion strength to Al alloy substrates was for the ∼210 nm thick coating, due to a continuous film coverage and low internal stress. Electrochemical measurements indicated that sputter deposited crystalline CeO{sub 2} coatings acted as physical barriers that provide good cathodic inhibition for Al alloys in saline solution. The ∼900 nm thick CeO{sub 2} coated sample had the best corrosion performance that increased the corrosion resistance by two orders magnitude and lowered the cathodic current density 30 times compared to bare Al 2024-T3 substrates. The reduced defects and exposed surface, along with suppressed charge mobility, likely accounts for the improved corrosion performance as coating thickness increased from ∼100 nm to ∼900 nm. The corrosion performance decreased for ∼1400 nm thick coatings due in part to an increase in coating defects and porosity along with a decrease in adhesion strength.

Effect of silicon solar cell processing parameters and crystallinity on mechanical strength

Energy Technology Data Exchange (ETDEWEB)

Popovich, V.A.; Yunus, A.; Janssen, M.; Richardson, I.M. [Delft University of Technology, Department of Materials Science and Engineering, Delft (Netherlands); Bennett, I.J. [Energy Research Centre of the Netherlands, Solar Energy, PV Module Technology, Petten (Netherlands)

2011-01-15

Silicon wafer thickness reduction without increasing the wafer strength leads to a high breakage rate during subsequent handling and processing steps. Cracking of solar cells has become one of the major sources of solar module failure and rejection. Hence, it is important to evaluate the mechanical strength of solar cells and influencing factors. The purpose of this work is to understand the fracture behavior of silicon solar cells and to provide information regarding the bending strength of the cells. Triple junctions, grain size and grain boundaries are considered to investigate the effect of crystallinity features on silicon wafer strength. Significant changes in fracture strength are found as a result of metallization morphology and crystallinity of silicon solar cells. It is observed that aluminum paste type influences the strength of the solar cells. (author)

Fatigue strength of field welded joints in I-section girders of thick flange plates with cope hole details; Sukarappu wo yusuru atsuita I gata danmen keta genba yosetsu tsugitebu no hiro kyodo

Energy Technology Data Exchange (ETDEWEB)

Minami, K.; Miki, C.; Tateishi, K. [Tokyo Institute of Technology, Tokyo (Japan)

1997-10-15

Field welding an I-section girder forms details having scallop at the web, whereas the presence of the scallop causes shear deformation and localized stress concentration. Therefore the details in joints with low fatigue strength are ranked as class G in the fatigue design guideline published by JSSC. With special notice on the effect of shear, the present study has varied the phase by using multiple number of jacks; so loaded that the direction of the shear force will change; assumed field welding of a bridge constructed with a few number of main girders; and verified fatigue strength at thick flange plates. In addition, in order to improve the fatigue strength, elucidation was given on the effect of grinder finish at boxing welds. From these results, items to be considered were made clear when structural details are designed and fabricated, in which I-section girders having scallop are welded in fields. Furthermore, it was considered that stress in web plate jointing welding bead becomes relatively higher than local stress in boxing, which was indicated as a point requiring precaution. 8 refs., 20 figs., 2 tabs.

A Study on Changes in Thickness of STS304 Material in the Progressive Drawing Process

Directory of Open Access Journals (Sweden)

Lee C.K.

2017-06-01

Full Text Available In the drawing process, the roundness of corners in the punch and the die are very important factors in determining the thicknesses of the product. The results clearly revealed that the thickness of a flange was increased and the thickness of body parts reduced when the roundness of the die entrance was small. The material thickness of the top part was decreased when the corner roundness of the punch was large. The smooth inflow of materials was found to have a significant effect on the thickness during the post-process. The compressive strength of STS 304 material exhibited a higher value compared with other processing methods. Moreover, we clearly observed the corner roundness of the punch and the die to be a very important factor for STS 304 materials.

Finite plate thickness effects on the Rayleigh-Taylor instability in elastic-plastic materials

Science.gov (United States)

Polavarapu, Rinosh; Banerjee, Arindam

2017-11-01

The majority of theoretical studies have tackled the Rayleigh-Taylor instability (RTI) problem in solids using an infinitely thick plate. Recent theoretical studies by Piriz et al. (PRE 95, 053108, 2017) have explored finite thickness effects. We seek to validate this recent theoretical estimate experimentally using our rotating wheel RTI experiment in an accelerated elastic-plastic material. The test section consists of a container filled with air and mayonnaise (a non-Newtonian emulsion) with an initial perturbation between two materials. The plate thickness effects are studied by varying the depth of the soft-solid. A set of experiments is run by employing different initial conditions with different container dimensions. Additionally, the effect of acceleration rate (driving pressure rise time) on the instability threshold with reference to the finite thickness will also be inspected. Furthermore, the experimental results are compared to the analytical strength models related to finite thickness effects on RTI. Authors acknowledge financial support from DOE-SSAA Grant # DE-NA0003195 and LANL subcontract #370333.

Research on the compressive strength of a passenger vehicle roof

Science.gov (United States)

Zhao, Guanglei; Cao, Jianxiao; Liu, Tao; Yang, Na; Zhao, Hongguang

2017-05-01

To study the compressive strength of a passenger vehicle roof, this paper makes the simulation test on the static collapse of the passenger vehicle roof and analyzes the stress and deformation of the vehicle roof under pressure in accordance with the Roof Crush Resistance of Passenger Cars (GB26134-2010). It studies the optimization on the major stressed parts, pillar A, pillar B and the rail of roof, during the static collapse process of passenger vehicle roof. The result shows that the thickness of pillar A and the roof rail has significant influence on the compressive strength of the roof while that of pillar B has minor influence on the compressive strength of the roof.

Yield strength of attached copper film

International Nuclear Information System (INIS)

Zhang Yan; Zhang Jian-Min

2011-01-01

Variation of stress in attached copper film with an applied strain is measured by X-ray diffraction combined with a four-point bending method. A lower slope of the initial elastic segment of the curve of X-ray measured stress versus applied strain results from incomplete elastic strain transferred from the substrate to the film due to insufficiently strong interface cohesion. So the slope of the initial elastic segment of the X-ray stress (or X-ray strain directly) of the film against the substrate applied strain may be used to measure the film-substrate cohesive strength. The yield strength of the attached copper film is much higher than that of the bulk material and varies linearly with the inverse of the film thickness. (condensed matter: structural, mechanical, and thermal properties)

Preparation of environment-friendly 3D eggshell membrane-supported anatase TiO2 as a reusable photocatalyst for degradation of organic dyes

Science.gov (United States)

Li, Yaling; Zhou, Ji; Fan, Yunde; Ye, Yong; Tang, Bin

2017-12-01

We fabricated a low-cost and efficient composite photocatalyst material, combining eggshell membrane (ESM) and titanium dioxide (TiO2) nanoparticles, through self-assembly method. ESM with 3D porous structures provide scaffolds for TiO2 nanoparticles. Polyethyleneimine (PEI) was used to modify ESM by grafting amine groups. The microstructure and property of the fabricated composites were studied by various characterization methods. The composite was used for the photodegradation of Rhodamine B (RhB). The results demonstrate that the composite catalyst possesses good photocatalytic performance for dye degradation under sunlight irradiation simulated by a xenon lamp. Functionalization based on nanomaterials may promote the applications of ESM.

Nutritional Quality of Eggs of Amberlink and Hyline Layers Fed on Different Levels of Provitamin A-Biofortified Maize

Directory of Open Access Journals (Sweden)

GW Zeina

Full Text Available ABSTRACT The study was conducted to determine the interaction of types of maize (Provitamin A-biofortified maize (PABM versus white maize and strain of laying birds (Amberlink and Hyline on nutritional quality of eggs. Twenty-one of each of Amberlink and Hyline laying hens were fed on three diets for 30 days. Birds were distributed in a 3 × 2 factorial arrangement constituting three diets (0, 50 or 100 % of PABM and two strains (Amberlink & Hyline. There was a diet × strain interaction on egg shell weight, average daily feed intake, egg production, egg weight and egg shell thickness. Eggs produced by layers under 100 % PABM had lighter eggshell weight and lower eggshell percentage. In contrast, eggs produced by layers under 50 % PABM diet had signi-ficantly higher eggshell percentage, heavier egg shell weight and thicker eggshell. As the level of PABM increased, the yellow and red hue (Hunter a* and b* values significantly increased while the lightness values (Hunter L* values decreased. As the level of PABM in the ration increased, the vitamin A content of the egg yolk also significantly increased. Assimilation of vitamin A from feed to egg yolk in Amberlink and Hyline hens was similar. Hence, egg enrichment with vitamin A can be achieved by using PABM in layers ration. The use of high level of PABM had a negative effect on the eggshell quality traits.

Huffmanela markgracei sp. n. (Nematoda: Trichosomoididae) from buccal cavity of Atlantic sharpnose shark, Rhizoprionodon terraenovae (Carcharhiniformes: Carcharhinidae), in the northwestern Gulf of Mexico off Texas.

Science.gov (United States)

Ruiz, Carlos F; Bullard, Stephen A

2013-09-01

Eggs of Huffmanela markgracei sp. n. infected one of three Atlantic sharpnose sharks, Rhizoprionodon terraenovae (Richardson) (Carcharhiniformes: Carcharhinidae) captured by bottom long-line in the northwestern Gulf of Mexico off Padre Island, Texas. Eggs in the skin formed sinuous tracks (1-8 eggs wide; 1-4 eggs deep; 150 eggs/mm2) occupying a swath of the skin 22 cm x 2 cm on the tongue, branchial arches and the dorsal surface of the buccal cavity. Eggs had transverse eggshell ridges (branching and non-branching), had shells that were clear, amber or brown, and measured 90-113 microm (x = 102 +/- 4; n = 190) long, 38-54 microm (43 +/- 3; 190) wide, 3-5 microm (4 +/- 0; 190) in eggshell thickness with protruding polar plugs 8-12 microm (10 +/- 1; 190) wide. Apparently fully developed larvae in eggs were 255-335 microm (299 +/- 26; 30) long, 8-10 microm (9 +/- 1; 30) wide, and in-folded 5-6 (6 +/- 0; 30) times. Some of these larvae were emerging from eggs in the skin. The new species differs from congeners by the combination of having a large, spindle-shaped egg, transverse eggshell ridges, an envelope that is smooth, tightly-apposed to the eggshell and surrounds the entire eggshell inclusive of the polar plugs, and a large larva. This is the first report of a species of Huffmanela Moravec, 1987 from a chondrichthyan in the Gulf of Mexico and from a shark not assigned to Carcharhinus.

The effect of filler metal thickness on residual stress and creep for stainless-steel plate-fin structure

Energy Technology Data Exchange (ETDEWEB)

Jiang Wenchun [School of Mechanical and Power Engineering, Nanjing University of Technology, Nanjing 210009 (China)], E-mail: jiangwenchun@126.com; Gong Jianming; Chen Hu; Tu, S.T. [School of Mechanical and Power Engineering, Nanjing University of Technology, Nanjing 210009 (China)

2008-08-15

Stainless-steel plate-fin heat exchanger (PFHE) has been used as a high-temperature recuperator in microturbine for its excellent qualities in compact structure, high-temperature and pressure resistance. Plate-fin structure, as the core of PFHE, is fabricated by vacuum brazing. The main component fins and the parting sheets are joined by fusion of a brazing alloy cladded to the surface of parting sheets. Owing to the material mismatching between the filler metal and the base metal, residual stresses can arise and decrease the structure strength greatly. The recuperator serves at high temperature and the creep would happen. The thickness of the filler metal plays an important role in the joint strength. Hence this paper presented a finite element (FE) analysis of the brazed residual stresses and creep for a counterflow stainless-steel plate-fin structure. The effect of the filler metal thickness on residual stress and creep was investigated, which provides a reference for strength design.

Accounting sodium effect in calculation of strength of nuclear reactor components

International Nuclear Information System (INIS)

Nikitin, V.I.

1981-01-01

Accounting methods of liquid sodium effect on long-term strength and creep of structural materials of nuclear reactors are considered. The decrease of pearlite steel strength at the decarburization expense and the decrease of plasticity of austenitic steels at the expense of carburization are noted. The necessity to account thermal transfer of mass is shown. Values of safety factors are presented, they are recommended for the design of reactor component parts with the thickness not less than 1 mm [ru

Protective effect of soluble eggshell membrane protein hydrolysate on cardiac ischemia/reperfusion injury

Directory of Open Access Journals (Sweden)

Tao Yang

2015-12-01

Full Text Available Background: Soluble eggshell membrane protein (SEP has been proved to hold the antioxidant activity. The functional role of SEP on cardioprotection was investigated in vivo and in vitro. Methods: Rats and cardiomyocytes were pretreated with SP2, a hydrolysate attained from SEP, and then subjected to ischemia/reperfusion (I/R or hypoxia/reoxygenation (H/R and hydrogen peroxide, respectively. The measurement of myocardial infarct size, cell apoptosis assay, cell viability assay, and caspase activity assay were performed on rats and cardiomyocytes. Results: The results showed that the treatment of SP2 induced the resistance to I/R or H/R injury on rats and cardiomyocytes as indicated by decreased infarct size and decreased cellular apoptosis. The cardioprotective roles of SP2 were partly resulted from the downregulated expression and activity of caspase-3 in which the effect was similar to the caspase inhibitor, z-VAD-fmk, and could be rescued by caspase activator, PAC-1. Conclusions: This investigation has demonstrated that SP2 attenuated the damage of I/R and H/R on rats and cardiomyocytes by the caspase-dependent pathway. This cardioprotective effect of SP2 suggested a novel therapeutic agent of SEP for ischemic-related heart diseases.

Pea proteins oral supplementation promotes muscle thickness gains during resistance training: a double-blind, randomized, Placebo-controlled clinical trial vs. Whey protein.

Science.gov (United States)

Babault, Nicolas; Païzis, Christos; Deley, Gaëlle; Guérin-Deremaux, Laetitia; Saniez, Marie-Hélène; Lefranc-Millot, Catherine; Allaert, François A

2015-01-01

The effects of protein supplementation on muscle thickness and strength seem largely dependent on its composition. The current study aimed at comparing the impact of an oral supplementation with vegetable Pea protein (NUTRALYS®) vs. Whey protein and Placebo on biceps brachii muscle thickness and strength after a 12-week resistance training program. One hundred and sixty one males, aged 18 to 35 years were enrolled in the study and underwent 12 weeks of resistance training on upper limb muscles. According to randomization, they were included in the Pea protein (n = 53), Whey protein (n = 54) or Placebo (n = 54) group. All had to take 25 g of the proteins or placebo twice a day during the 12-week training period. Tests were performed on biceps muscles at inclusion (D0), mid (D42) and post training (D84). Muscle thickness was evaluated using ultrasonography, and strength was measured on an isokinetic dynamometer. Results showed a significant time effect for biceps brachii muscle thickness (P Pea, Whey and Placebo, respectively; P Pea group as compared to Placebo whereas there was no difference between Whey and the two other conditions. Muscle strength also increased with time with no statistical difference between groups. In addition to an appropriate training, the supplementation with pea protein promoted a greater increase of muscle thickness as compared to Placebo and especially for people starting or returning to a muscular strengthening. Since no difference was obtained between the two protein groups, vegetable pea proteins could be used as an alternative to Whey-based dietary products. The present trial has been registered at ClinicalTrials.gov (NCT02128516).

Efeito de diferentes níveis de sódio e fósforo sobre o desempenho e a qualidade da casca dos ovos de poedeiras comerciais Effect of different levels of sodium and phosphorus on performance and eggshell quality of laying hens

Directory of Open Access Journals (Sweden)

Douglas Emygdio de Faria

2000-04-01

Full Text Available Conduziu-se um experimento com o objetivo de verificar o efeito de diferentes níveis de sódio e fósforo (P sobre o desempenho e a qualidade da casca dos ovos e de determinados constituintes sangüíneos, em 144 galinhas Hy-Line W36, com 60 semanas de idade, distribuídas em 36 unidades experimentais com quatro aves cada. O delineamento utilizado foi o de blocos ao acaso em arranjo fatorial (3 x 3, níveis de sódio (0,16; 0,20; e 0,24% e níveis de fósforo total (0,35; 0,45; e 0,55%, totalizando nove tratamentos, dois blocos com duas repetições em cada bloco. As rações experimentais foram isoprotéicas (16,0% de PB, isocalóricas (2800 kcal de EM/kg e isocálcicas (4,0% de Ca. Consumo de ração, produção e massa de ovos, conversão alimentar, porcentagem e espessura da casca e densidade aparente dos ovos não foram alteradas pelos níveis de sódio. Entretanto, quando as galinhas foram alimentadas com dietas contendo 0,35% de P total, verificou-se comprometimento da produção e massa de ovos e conversão alimentar, sem alteração das características de qualidade da casca. Houve interação entre os fatores para o peso dos ovos. Baixos níveis de P total não foram efetivos em melhorar a qualidade da casca dos ovos, mas prejudicaram o desempenho das galinhas.An experiment was carried out to verify the effect of different levels of sodium and phosphorus (P on the performance, eggshell quality and on some blood constituents of 144 laying hens Hy-Line W36, aged 60 weeks, allotted to 36 experimental units with four hens each. A randomized experimental block design was used in a factorial arrangement (3 x 3, sodium levels (.16, .20 and .24% and phosphorus levels (.35, .45 and .55%, totalizing nine treatments, two blocks with two replicates each. The experimental diets were isoproteic (16.0% CP, isoenergetic (2,800 kcal ME/kg and isocalcium (4.0% Ca. Feed intake, egg production, egg mass, feed:gain ratio, shell percentage, shell thickness

Fatigue qualification of high thickness composite rotor components

Science.gov (United States)

Raggi, M.; Mariani, U.; Zaffaroni, G.

Fatigue qualification aspects of composite rotor components are presented according with the safe life procedure usually applied by helicopter manufacturers. Test activities are identified at three levels of specimen complexity: coupon, structural element and full scale component. Particular attention is given to high thickness laminates qualification as far as environmental exposure is concerned. A practical approach for an accelerated conditioning procedure is described. The application to a main rotor tension link is presented showing the negligible effect of the moisture absorption on its fatigue strength.

Effect of Reduction in Thickness and Rolling Conditions on Mechanical Properties and Microstructure of Rolled Mg-8Al-1Zn-1Ca Alloy

Directory of Open Access Journals (Sweden)

Yuta Fukuda

2017-01-01

Full Text Available A cast Mg-8Al-1Zn-1Ca magnesium alloy was multipass hot rolled at different sample and roll temperatures. The effect of the rolling conditions and reduction in thickness on the microstructure and mechanical properties was investigated. The optimal combination of the ultimate tensile strength, 351 MPa, yield strength, 304 MPa, and ductility, 12.2%, was obtained with the 3 mm thick Mg-8Al-1Zn-1Ca rolled sheet, which was produced with a roll temperature of 80°C and sample temperature of 430°C. This rolling process resulted in the formation of a bimodal structure in the α-Mg matrix, which consequently led to good ductility and high strength, exclusively by the hot rolling process. The 3 mm thick rolled sheet exhibited fine (mean grain size of 2.7 μm and coarse grain regions (mean grain size of 13.6 μm with area fractions of 29% and 71%, respectively. In summary, the balance between the strength and ductility was enhanced by the grain refinement of the α-Mg matrix and by controlling the frequency and orientation of the grains.

Full reflector thickness and isolation thickness on neutron transport

International Nuclear Information System (INIS)

Sakai, Tomohiro; Naito, Yoshitaka; Komuro, Yuichi.

1988-08-01

A method to determine ''full reflector thickness'' and ''isolation thickness'', which is utilized for criticality safety evaluation on nuclear fuel facilities, was proposed in this paper. Firstly, a calculation was tryed to obtain the two kinds of thicknesses from the result of criticality calculations for a specific case. Then, two simple equations which calculates the two kinds of thicknesses were made from the relation between reflector (or isolator) thickness and k eff , and one-group diffusion theory. Finally, we proposed a new method to determine the thicknesses. From the method we proposed, ''full reflector thickness'' and ''isolation thickness'' can be obtain using the equations and migration length of the reflector (or isolator) and infinite and effective multiplication factor of the fuel. (author)

Tensile test of a silicon microstructure fully coated with submicrometer-thick diamond like carbon film using plasma enhanced chemical vapor deposition method

Science.gov (United States)

Zhang, Wenlei; Uesugi, Akio; Hirai, Yoshikazu; Tsuchiya, Toshiyuki; Tabata, Osamu

2017-06-01

This paper reports the tensile properties of single-crystal silicon (SCS) microstructures fully coated with sub-micrometer thick diamond like carbon (DLC) film using plasma enhanced chemical vapor deposition (PECVD). To minimize the deformations or damages caused by non-uniform coating of DLC, which has high compression residual stress, released SCS specimens with the dimensions of 120 µm long, 4 µm wide, and 5 µm thick were coated from the top and bottom side simultaneously. The thickness of DLC coating is around 150 nm and three different bias voltages were used for deposition. The tensile strength improved from 13.4 to 53.5% with the increasing of negative bias voltage. In addition, the deviation in strength also reduced significantly compared to bare SCS sample.

Characterization of a glass frit free TiCuAg-thick film metallization applied on aluminium nitride

International Nuclear Information System (INIS)

Reicher, R.; Smetana, W.; Adlassnig, A.; Schuster, J. C.; Gruber, U.

1997-01-01

The metallization of aluminium nitride substrates by glass frit free Ti CuAg-thick film pastes were investigated. Adhesion properties of the conductor paste were tested by measuring tensile strength and compared with commercial Cu-thick film pastes (within glass frit). Also numerical analysis of temperature-distribution and thermal extension of metallized aluminium nitride ceramic, induced by a continuous and a pulsed working electronic device were made with a finite element program. (author)

Experimental collaboration for thick concrete structures with alkali-silica reaction

Science.gov (United States)

Ezell, N. Dianne Bull; Hayes, Nolan; Lenarduzzi, Roberto; Clayton, Dwight; Ma, Z. John; Le Pape, Sihem; Le Pape, Yann

2018-04-01

Alkali-Silica Reaction (ASR) is a reaction that occurs over time in concrete between alkaline cement paste and reactive, non-crystalline silica in aggregates. An expansive gel is formed within the aggregates which results in micro-cracks in aggregates and adjacent cement paste. The reaction requires the presence of water and has been predominantly detected in groundwater-impacted portions of below grade structures, with limited impact to exterior surfaces in above grade structures. ASR can potentially affect concrete properties and performance characteristics such as compressive strength, modulus of elasticity, shear strength, and tensile strength. Since ASR degradation often takes significant amounts of time, developing ASR detection techniques is important to the sustainability and extended operation lifetimes of nuclear power plants (NPPs). The University of Tennessee, Knoxville (UTK) in collaboration with Oak Ridge National Laboratory (ORNL) designed and built an experiment representative of typical NPP structures to study ASR in thick concrete structures.

Influences of layer thickness on the compatibility and physical properties of polycarbonate/polystyrene multilayered film via nanolayer coextrusion

Science.gov (United States)

Cheng, Junfeng; Chen, Zhiru; Zhou, Jiaqi; Cao, Zheng; Wu, Dun; Liu, Chunlin; Pu, Hongting

2018-05-01

The effects of layer thickness on the compatibility between polycarbonate (PC) and polystyrene (PS) and physical properties of PC/PS multilayered film via nanolayer coextrusion are studied. The morphology of multilayered structure is observed using a scanning electron microscope. This multilayered structure may have a negative impact on the transparency, but it can improve the water resistance and heat resistance of film. To characterize the compatibility between PC and PS, differential scanning calorimetry is used to measure the glass transition temperature. The compatibility is found to be improved with the decrease of layer thickness. Therefore, the viscosity of multilayered film is also reduced with the decrease of layer thickness. In addition, the multilayered structure can improve the tensile strength with the increase of layer numbers. Because of the complete and continuous layer structure of PC, the PC/PS multilayered film can retain its mechanical strength at the temperature above Tg of PS.

Characterization of avian eggshell waste aiming its use in a ceramic wall tile paste Caracterização de resíduo de casca de ovo visando seu aproveitamento em revestimento cerâmico poroso

Directory of Open Access Journals (Sweden)

M. N. Freire

2006-12-01

Full Text Available In Brazil, the food industry generates every year huge amounts of avian eggshell waste, and a critical question is to find an adequate use for this waste. The aim of this work is to determine the chemical, mineralogical and physical characteristics of a nonprocessed avian eggshell waste sample, as well as to investigate its use in wall tile paste. The sample was analyzed regarding to chemical composition, X-ray diffraction, morphology, particle size analysis, density, organic matter, soluble salts, and thermal analysis. The results indicated that the eggshell waste sample rich in CaCO3 can be used as an alternative raw material in the production of wall tile materials.No Brasil a indústria alimentícia gera enormes quantidades de resíduo de casca de ovo galináceo todo ano, e uma questão crítica é estabelecer um uso adequado para este resíduo. O objetivo deste trabalho é estudar as características química, mineralógica e física de uma amostra de resíduo de casca de ovo natural, bem como avaliar sua utilização em revestimento cerâmico poroso. A amostra de resíduo de casca de ovo foi caracterizada com relação à composição química, difração de raios X, morfologia, análise de tamanho de partícula, massa específica, matéria orgânica, sais solúveis e análise térmica. Os resultados mostraram que o resíduo de casca de ovo rico em CaCO3 pode ser usado como uma matéria-prima alternativa na produção de revestimento cerâmico poroso (azulejo.

Effect of layer thickness on the properties of nickel thermal sprayed steel

Energy Technology Data Exchange (ETDEWEB)

Nurisna, Zuhri, E-mail: zuhri-nurisna@yahoo.co.id; Triyono,, E-mail: triyonomesin@uns.ac.id; Muhayat, Nurul, E-mail: nurulmuhayat@staff.uns.ac.id; Wijayanta, Agung Tri, E-mail: agungtw@uns.ac.id [Department of Mechanical Engineering, Sebelas Maret University, Jl. Jr. Sutami 36 A, Surakarta (Indonesia)

2016-03-29

Thermal arc spray nickel coating is widely used for decorative and functional applications, by improving corrosion resistance, wear resistance, heat resistence or by modifying other properties of the coated materials. There are several properties have been studied. Layer thickness of nickel thermal sprayed steel may be make harder the substrate surface. In this study, the effect of layer thickness of nickel thermal sprayed steel has been investigated. The rectangular substrate specimens were coated by Ni–5 wt.% Al using wire arc spray method. The thickness of coating layers were in range from 0.4 to 1.0 mm. Different thickness of coating layers were conducted to investigate their effect on hardness and morphology. The coating layer was examined by using microvickers and scanning electron microscope with EDX attachment. Generally, the hardness at the interface increased with increasing thickness of coating layers for all specimens due to higher heat input during spraying process. Morphology analysis result that during spraying process aluminum would react with surrounding oxygen and form aluminum oxide at outer surface of splat. Moreover, porosity was formed in coating layers. However, presence porosity is not related to thickness of coating material. The thicker coating layer resulted highesr of hardness and bond strength.

Fragmentation of spin-dipole strength in 90Zr and 208Pb

International Nuclear Information System (INIS)

Marketin, T.; Litvinova, E.; Vretenar, D.; Ring, P.

2012-01-01

An extension of time-dependent covariant density functional theory that includes particle-vibration coupling is applied to the charge-exchange channel. Spin-dipole excitation spectra are calculated an compared to available data for 90 Zr and 208 Pb. A significant fragmentation is found for all three angular-momentum components of the spin-dipole strength as a result of particle-vibration coupling, as well as a shift of a portion of the strength to higher energy. A high-energy tail is formed in the strength distribution that linearly decreases with energy. Using a model-independent sum rule, the corresponding neutron skin thickness is estimated and shown to be consistent with values obtained at the mean-field level.

Response of mantle transition zone thickness to plume buoyancy flux

Science.gov (United States)

Das Sharma, S.; Ramesh, D. S.; Li, X.; Yuan, X.; Sreenivas, B.; Kind, R.

2010-01-01

The debate concerning thermal plumes in the Earth's mantle, their geophysical detection and depth characterization remains contentious. Available geophysical, petrological and geochemical evidence is at variance regarding the very existence of mantle plumes. Utilizing P-to-S converted seismic waves (P receiver functions) from the 410 and 660 km discontinuities, we investigate disposition of these boundaries beneath a number of prominent hotspot regions. The thickness of the mantle transition zone (MTZ), measured as P660s-P410s differential times (tMTZ), is determined. Our analyses suggest that the MTZ thickness beneath some hotspots correlates with the plume strength. The relationship between tMTZ, in response to the thermal perturbation, and the strength of plumes, as buoyancy flux B, follows a power law. This B-tMTZ behavior provides unprecedented insights into the relation of buoyancy flux and excess temperature at 410-660 km depth below hotspots. We find that the strongest hotspots, which are located in the Pacific, are indeed plumes originating at the MTZ or deeper. According to the detected power law, even the strongest plumes may not shrink the transition zone by significantly more than ~40 km (corresponding to a maximum of 300-400° excess temperature).

Modeling of Sylgard Adhesive Strength

Energy Technology Data Exchange (ETDEWEB)

Stevens, Ralph Robert [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-02-03

Sylgard is the name of a silicone elastomeric potting material manufactured by Dow Corning Corporation.1 Although the manufacturer cites its low adhesive strength as a feature of this product, thin layers of Sylgard do in fact have a non-negligible strength, which has been measured in recent tensile and shear debonding tests. The adhesive strength of thin layers of Sylgard potting material can be important in applications in which components having signi cantly di erent thermal expansion properties are potted together, and the potted assembly is subjected to temperature changes. The tensile and shear tractions developed on the potted surfaces of the components can cause signi cant internal stresses, particularly for components made of low-strength materials with a high area-to-volume ratio. This report is organized as follows: recent Sylgard debonding tests are rst brie y summarized, with particular attention to the adhesion between Sylgard and PBX 9501, and also between Sylgard and aluminum. Next, the type of numerical model that will be used to simulate the debonding behavior exhibited in these tests is described. Then the calibration of the debonding model will be illustrated. Finally, the method by which the model parameters are adjusted (scaled) to be applicable to other, non- tested bond thicknesses is summarized, and all parameters of the model (scaled and unscaled) are presented so that other investigators can reproduce all of the simulations described in this report as well as simulations of the application of interest.

The biomechanical, chemical and physiological adaptations of the eggs of two Australian megapodes to their nesting strategies and their implications for extinct titanosaur dinosaurs.

Science.gov (United States)

Grellet-Tinner, G; Lindsay, S; Thompson, M B

2017-08-01

Megapodes are galliform birds endemic to Australasia and unusual among modern birds in that they bury their eggs for incubation in diverse substrates and using various strategies. Alectura lathami and Leipoa ocellata are Australian megapodes that build and nest in mounds of soil and organic matter. Such unusual nesting behaviours have resulted in particular evolutionary adaptations of their eggs and eggshells. We used a combination of scanning electron microscopy, including electron backscatter diffraction and energy-dispersive X-ray spectroscopy, to determine the fine structure of the eggshells and micro-CT scanning to map the structure of pores. We discovered that the surface of the eggshell of A. lathami displays nodes similar to those of extinct titanosaur dinosaurs from Transylvania and Auca Mahuevo egg layer #4. We propose that this pronounced nodular ornamentation is an adaptation to an environment rich in organic acids from their nest mound, protecting the egg surface from chemical etching and leaving the eggshell thickness intact. By contrast, L. ocellata nests in mounds of sand with less organic matter in semiarid environments and has eggshells with weakly defined nodes, like those of extinct titanosaurs from AM L#3 that also lived in a semiarid environment. We suggest the internode spaces in both megapode and titanosaur species act as funnels, which concentrate the condensed water vapour between the nodes. This water funnelling in megapodes through the layer of calcium phosphate reduces the likelihood of bacterial infection by creating a barrier to microbial invasion. In addition, the accessory layer of both species possesses sulphur, which reinforces the calcium phosphate barrier to bacterial and fungal contamination. Like titanosaurs, pores through the eggshell are Y-shaped in both species, but A. lathami displays unique mid-shell connections tangential to the eggshell surface and that connect some adjacent pores, like the eggshells of titanosaur of AM

Alterations of bone microstructure and strength in end-stage renal failure.

Science.gov (United States)

Trombetti, A; Stoermann, C; Chevalley, T; Van Rietbergen, B; Herrmann, F R; Martin, P-Y; Rizzoli, R

2013-05-01

End-stage renal disease (ESRD) patients have a high risk of fractures. We evaluated bone microstructure and finite-element analysis-estimated strength and stiffness in patients with ESRD by high-resolution peripheral computed tomography. We observed an alteration of cortical and trabecular bone microstructure and of bone strength and stiffness in ESRD patients. Fragility fractures are common in ESRD patients on dialysis. Alterations of bone microstructure contribute to skeletal fragility, independently of areal bone mineral density. We compared microstructure and finite-element analysis estimates of strength and stiffness by high-resolution peripheral quantitative computed tomography (HR-pQCT) in 33 ESRD patients on dialysis (17 females and 16 males; mean age, 47.0 ± 12.6 years) and 33 age-matched healthy controls. Dialyzed women had lower radius and tibia cortical density with higher radius cortical porosity and lower tibia cortical thickness, compared to controls. Radius trabecular number was lower with higher heterogeneity of the trabecular network. Male patients displayed only a lower radius cortical density. Radius and tibia cortical thickness correlated negatively with bone-specific alkaline phosphatase (BALP). Microstructure did not correlate with parathyroid hormone (PTH) levels. Cortical porosity correlated positively with "Kidney Disease: Improving Global Outcomes" working group PTH level categories (r = 0.36, p microstructure and calculated bone strength are altered in ESRD patients, predominantly in women. Bone microstructure and biomechanical assessment by HR-pQCT may be of major clinical relevance in the evaluation of bone fragility in ESRD patients.

Strength evaluation of prosthetic check sockets, copolymer sockets, and definitive laminated sockets.

Science.gov (United States)

Gerschutz, Maria J; Haynes, Michael L; Nixon, Derek; Colvin, James M

2012-01-01

A prosthesis encounters loading through forces and torques exerted by the person with amputation. International Organization for Standardization (ISO) standard 10328 was designed to test most lower-limb prosthetic components. However, this standard does not include prosthetic sockets. We measured static failure loads of prosthetic sockets using a modified ISO 10328 and then compared them with the criteria set by this standard for other components. Check socket (CS) strengths were influenced by thickness, material choice, and fabrication method. Copolymer socket (CP) strengths depended on thickness and fabrication methods. A majority of the CSs and all of the CPs failed to pass the ISO 10328 ductile loading criterion. In contrast, the strengths of definitive laminated sockets (DLs) were influenced more by construction material and technique. A majority of the DLs failed to pass the ISO 10328 brittle loading criterion. Analyzing prosthetic sockets from a variety of facilities demonstrated that socket performance varies considerably between and within facilities. The results from this article provide a foundation for understanding the quality of prosthetic sockets, some insight into possible routes for improving the current care delivered to patients, and a comparative basis for future technology.

The technology and welding joint properties of hybrid laser-tig welding on thick plate

Science.gov (United States)

Shenghai, Zhang; Yifu, Shen; Huijuan, Qiu

2013-06-01

The technologies of autogenous laser welding and hybrid laser-TIG welding are used on thick plate of high strength lower alloy structural steel 10CrNiMnMoV in this article. The unique advantages of hybrid laser-TIG welding is summarized by comparing and analyzing the process parameters and welding joints of autogenous laser welding laser welding and hybrid laser-TIG welding. With the optimal process parameters of hybrid welding, the good welding joint without visible flaws can be obtained and its mechanical properties are tested according to industry standards. The results show that the hybrid welding technology has certain advantages and possibility in welding thick plates. It can reduce the demands of laser power, and it is significant for lowering the aspect ratio of weld during hybrid welding, so the gas in the molten pool can rise and escape easily while welding thick plates. Therefore, the pores forming tendency decreases. At the same time, hybrid welding enhances welding speed, and optimizes the energy input. The transition and grain size of the microstructure of hybrid welding joint is better and its hardness is higher than base material. Furthermore, its tensile strength and impact toughness is as good as base material. Consequently, the hybrid welding joint can meet the industry needs completely.

EFFECTS OF STRENGTH VS. BALLISTIC-POWER TRAINING ON THROWING PERFORMANCE

Directory of Open Access Journals (Sweden)

Nikolaos Zaras

2013-03-01

Full Text Available The purpose of the present study was to investigate the effects of 6 weeks strength vs. ballistic-power (Power training on shot put throwing performance in novice throwers. Seventeen novice male shot-put throwers were divided into Strength (N = 9 and Power (n = 8 groups. The following measurements were performed before and after the training period: shot put throws, jumping performance (CMJ, Wingate anaerobic performance, 1RM strength, ballistic throws and evaluation of architectural and morphological characteristics of vastus lateralis. Throwing performance increased significantly but similarly after Strength and Power training (7.0-13.5% vs. 6.0-11.5%, respectively. Muscular strength in leg press increased more after Strength than after Power training (43% vs. 21%, respectively, while Power training induced an 8.5% increase in CMJ performance and 9.0 - 25.8% in ballistic throws. Peak power during the Wingate test increased similarly after Strength and Power training. Muscle thickness increased only after Strength training (10%, p < 0.05. Muscle fibre Cross Sectional Area (fCSA increased in all fibre types after Strength training by 19-26% (p < 0.05, while only type IIx fibres hypertrophied significantly after Power training. Type IIx fibres (% decreased after Strength but not after Power training. These results suggest that shot put throwing performance can be increased similarly after six weeks of either strength or ballistic power training in novice throwers, but with dissimilar muscular adaptations

Methanolysis of Crude Jatropha Oil using Heterogeneous Catalyst from the Seashells and Eggshells as Green Biodiesel

Directory of Open Access Journals (Sweden)

A. N. R. REDDY

2017-07-01

Full Text Available In this work, heterogeneous calcium oxide catalysts gleaned from Polymedosa expansa and eggshell were investigated for the transesterification of crude jatropha oil with methanol, to access their prospective performance in biodiesel production as an alternative green energy resource. The best yield of biodiesel achieved was 96% in 1 h for Step 1 using 0.01:1 ratio of acid catalyst to oil and 0.6:1 ratio of alcohol to oil ratio, together with 2 h of Step 2 using 0.02:1 ratio with base catalyst CaO, derived from P. expansa, to oil ratio and 5:1 ratio of alcohol to oil.  The properties of jatropha biodiesel were analyzed and found to have calorific value of 35.43 MJ/kg, density value of 895 kg/m3 and flash point of 167. The biodiesel was blended with mineral diesel from B0 to B50 for a diesel engine performance test. B20 indicated comparable characteristics with pure mineral diesel, like lowest fuel consumption rate, specific fuel consumption rate, highest brake horsepower and mechanical efficiency.

Effect of dietary supplementation of Ligustrum lucidum on performance, egg quality and blood biochemical parameters of Hy-Line Brown hens during the late laying period.

Science.gov (United States)

Li, X L; He, W L; Yang, M L; Yan, Y M; Xue, Y H; Zhao, S T

2017-11-01

The fruit of Ligustrum lucidum (FLL, Nuzhenzi in Chinese) is an important traditional medicine, and have attracted significant research attention because of their various biological activities. However, there are few research reports available on the use of FLL as a feed additive in livestock nutrition, particularly in layers. This study was conducted to determine the effects of supplementation of the diet of laying hens with FLL on laying performance, egg quality and blood metabolites. A total of 360 72-week-old hens were allocated to three dietary treatments (eight replications of 15 hens/treatment group) and were fed either a control diet or a diet supplemented with an inclusion level of 0.25% or 0.50% of FLL powder in the final feed, until 78 weeks of age. Hens were housed in a three-tier cage system. Feed and water were provided ad libitum. Blood samples and eggs were collected at the end of the experiment. The results showed that dietary supplementation with FLL did not affect egg weight, feed conversion ratio, eggshell thickness, albumen height, egg yolk color, eggshell breaking strength or egg shape index. However, FLL supplementation significantly decreased (Phens fed FLL compared with the control group. It can be concluded that FLL, at a supplementation level of 0.25% final feed, can be used as an effective feed additive to improve the performance of laying hens during the late laying period.

Evaluation of the strength and radiopacity of Portland cement with varying additions of bismuth oxide.

Science.gov (United States)

Saliba, E; Abbassi-Ghadi, S; Vowles, R; Camilleri, J; Hooper, S; Camilleri, J

2009-04-01

To study the effect of addition of various proportions of bismuth oxide on compressive strength and radiopacity of Portland cement. The compressive strength of white Portland cement and cement replaced with 10, 15, 20, 25 and 30% bismuth oxide was evaluated by testing cylinders 6 mm in diameter and 12 mm high. Twelve cylinders were tested for each material under study. The radiopacity of the cements tested was evaluated using an aluminium step-wedge and densitometer. The optical density was compared with the relevant thickness of aluminium (Al). Statistical analysis was performed using Analysis of Variance (ANOVA) with P = 0.05 and Tukey test to perform multiple comparison tests. Various additions of bismuth oxide had no significant effect on the strength of the material when compared with the unmodified Portland cement (P > 0.05). The radiopacity of the cements tested ranged from 2.02 mm Al for Portland cement to 9.79 mm Al for the highest bismuth replacement. Addition of bismuth oxide did not affect the compressive strength of Portland cement. All the bismuth oxide cement mixtures had radio-opacities higher than 3 mm thickness of aluminium.

Deep Drawing of High-Strength Tailored Blanks by Using Tailored Tools

Directory of Open Access Journals (Sweden)

Thomas Mennecart

2016-01-01

Full Text Available In most forming processes based on tailored blanks, the tool material remains the same as that of sheet metal blanks without tailored properties. A novel concept of lightweight construction for deep drawing tools is presented in this work to improve the forming behavior of tailored blanks. The investigations presented here deal with the forming of tailored blanks of dissimilar strengths using tailored dies made of two different materials. In the area of the steel blank with higher strength, typical tool steel is used. In the area of the low-strength steel, a hybrid tool made out of a polymer and a fiber-reinforced surface replaces the steel half. Cylindrical cups of DP600/HX300LAD are formed and analyzed regarding their formability. The use of two different halves of tool materials shows improved blank thickness distribution, weld-line movement and pressure distribution compared to the use of two steel halves. An improvement in strain distribution is also observed by the inclusion of springs in the polymer side of tools, which is implemented to control the material flow in the die. Furthermore, a reduction in tool weight of approximately 75% can be achieved by using this technique. An accurate finite element modeling strategy is developed to analyze the problem numerically and is verified experimentally for the cylindrical cup. This strategy is then applied to investigate the thickness distribution and weld-line movement for a complex geometry, and its transferability is validated. The inclusion of springs in the hybrid tool leads to better material flow, which results in reduction of weld-line movement by around 60%, leading to more uniform thickness distribution.

An Approach for Measuring the Dielectric Strength of OLED Materials

Directory of Open Access Journals (Sweden)

Sujith Sudheendran Swayamprabha

2018-06-01

Full Text Available Surface roughness of electrodes plays a key role in the dielectric breakdown of thin-film organic devices. The rate of breakdown will increase when there are stochastic sharp spikes on the surface of electrodes. Additionally, surface having spiking morphology makes the determination of dielectric strength very challenging, specifically when the layer is relatively thin. We demonstrate here a new approach to investigate the dielectric strength of organic thin films for organic light-emitting diodes (OLEDs. The thin films were deposited on a substrate using physical vapor deposition (PVD under high vacuum. The device architectures used were glass substrate/indium tin oxide (ITO/organic material/aluminum (Al and glass substrate/Al/organic material/Al. The dielectric strength of the OLED materials was evaluated from the measured breakdown voltage and layer thickness.

Obtaining Thickness-Limited Electrospray Deposition for 3D Coating.

Science.gov (United States)

Lei, Lin; Kovacevich, Dylan A; Nitzsche, Michael P; Ryu, Jihyun; Al-Marzoki, Kutaiba; Rodriguez, Gabriela; Klein, Lisa C; Jitianu, Andrei; Singer, Jonathan P

2018-04-04

Electrospray processing utilizes the balance of electrostatic forces and surface tension within a charged spray to produce charged microdroplets with a narrow dispersion in size. In electrospray deposition, each droplet carries a small quantity of suspended material to a target substrate. Past electrospray deposition results fall into two major categories: (1) continuous spray of films onto conducting substrates and (2) spray of isolated droplets onto insulating substrates. A crossover regime, or a self-limited spray, has only been limitedly observed in the spray of insulating materials onto conductive substrates. In such sprays, a limiting thickness emerges, where the accumulation of charge repels further spray. In this study, we examined the parametric spray of several glassy polymers to both categorize past electrospray deposition results and uncover the critical parameters for thickness-limited sprays. The key parameters for determining the limiting thickness were (1) field strength and (2) spray temperature, related to (i) the necessary repulsive field and (ii) the ability for the deposited materials to swell in the carrier solvent vapor and redistribute charge. These control mechanisms can be applied to the uniform or controllably-varied microscale coating of complex three-dimensional objects.

Influence of N-rich material in valorization of industrial eggshell by co-composting.

Science.gov (United States)

Soares, Micaela A R; Quina, Margarida J; Quinta-Ferreira, Rosa

2016-11-01

Industrial eggshell (ES) is an animal by-product (ABP) involving some risk if not properly managed. Composting is a possible treatment approved for its safe use. This study aims to assess the influence of using N-rich material (grass clippings (GC)) to improve co-composting of ES mixtures for reaching sanitizing temperatures imposed by the ABP regulation from the European Union. Two sets of mixtures (M1 and M2) were investigated, each containing industrial potato peel waste, GC and rice husks at 3:1.9:1 and 3:0:1 ratios by wet weight. In each set, ES composition ranged from 0% to 30% (w/w). Co-composting trials were performed in self-heating reactors for 25 days, followed by maturation in piles. Results showed that only M1 trials attained temperatures higher than 70°C for nine consecutive hours, but N-losses by stripping on average were four- to five-fold higher than M2. In the absence of N-rich material, biodegradability of mixtures was 'low' to 'moderate' and organic matter conversion was impaired. Physical, chemical and phytotoxic properties of finished composts were suitable for soil improvement, but M1 took 54 more days to achieve maturity. In conclusion, co-composting ES with N-rich materials is important to assure the fulfilment of sanitizing requirements, avoiding any additional thermal treatment.

Inhomogeneity of Microstructure and Properties of 7085-T651 Aluminum Alloy Extra-thick Plate

Directory of Open Access Journals (Sweden)

LI Chengbo

2016-12-01

Full Text Available Inhomogeneity of microstructure and properties of 7085-T651 aluminum alloy extra-thick plate were investigated by tensile properties, exfoliation corrosion, optical microscopy(OM, composition analysis, scanning electron microscopy(SEM,differential scanning calorimetry (DSC and transmission electron microscopy (TEM. The results show that the microstructure, tensile property and exfoliation corrosion in different layers of 7085-T651 aluminum alloy of 110 mm thick are inhomogeneous. For the 1/4 thickness layer, the tensile strength is the minimum, 540 MPa, and the resistance to exfoliation corrosion of this layer is the worst, with exfoliation corrosion classification of EB. For the core layer, the tensile strength is the maximum, 580 MPa. The resistance to exfoliation corrosion of the surface layer is the best, with exfoliation corrosion classification of EA. For the 1/4 thickness layer, it has the largest recrystallized fraction up to about 47.7% and the grain size is about 105 μm; there are equilibrium phase particles precipitated on grain boundaries or within grains; the size of aging precipitates is small; and thus both mechanical properties and resistance to exfoliation corrosion are the worst. For the core layer, it has the smallest recrystallized fraction of about 14.8% and there are a large amount of sub-grains; the fraction of residual phase Al7Cu2Fe almost reaches up to about 1.43%; the size of the equilibrium phase on grain boundaries, the size of aging precipitates and the width of PFZ are large, and therefore good mechanical properties and bad resistance to exfoliation corrosion are obtained.

Microbial abundance on the eggs of a passerine bird and related fitness consequences between urban and rural habitats.

Science.gov (United States)

Lee, Sang-Im; Lee, Hyunna; Jablonski, Piotr G; Choe, Jae Chun; Husby, Magne

2017-01-01

Urban environments present novel and challenging habitats to wildlife. In addition to well-known difference in abiotic factors between rural and urban environments, the biotic environment, including microbial fauna, may also differ significantly. In this study, we aimed to compare the change in microbial abundance on eggshells during incubation between urban and rural populations of a passerine bird, the Eurasian Magpie (Pica pica), and examine the consequences of any differences in microbial abundances in terms of hatching success and nestling survival. Using real-time PCR, we quantified the abundances of total bacteria, Escherichia coli/Shigella spp., surfactin-producing Bacillus spp. and Candida albicans on the eggshells of magpies. We found that urban magpie eggs harboured greater abundances of E. coli/Shigella spp. and C. albicans before incubation than rural magpie eggs. During incubation, there was an increase in the total bacterial load, but a decrease in C. albicans on urban eggs relative to rural eggs. Rural eggs showed a greater increase in E. coli/Shigella spp. relative to their urban counterpart. Hatching success of the brood was generally lower in urban than rural population. Nestling survival was differentially related with the eggshell microbial abundance between urban and rural populations, which was speculated to be the result of the difference in the strength of the interaction among the microbes. This is the first demonstration that avian clutches in urban and rural populations differ in eggshell microbial abundance, which can be further related to the difference in hatching success and nestling survival in these two types of environments. We suggest that future studies on the eggshell microbes should investigate the interaction among the microbes, because the incubation and/or environmental factors such as urbanization or climate condition can influence the dynamic interactions among the microbes on the eggshells which can further determine the

Strength analysis of copper gas pipeline span

OpenAIRE

Ianevski, Philipp

2016-01-01

The purpose of the study was to analyze the stresses in a gas pipeline. While analyzing piping systems located inside building were used. Calculation of the strength of a gas pipeline is done by using information of the thickness of pipe walls, by choosing the suitable material, inner and outer diameter for the pipeline. Data for this thesis was collected through various internet sources and different books. From the study and research, the final results were reached and calculations were ...

Fatigue strength of laser welded joint sheet; Laser yosetsu tsugite no hiro kyodo

Energy Technology Data Exchange (ETDEWEB)

Fujii, A; Yoshimura, T; Tsuboi, M; Takasago, T; Nishio, T [Toyota Motor Corp., Aichi (Japan)

1997-10-01

In this paper, fatigue strength of laser welded butt joint has been investigated. In order to obtain the influence of underfill and pitting, fatigue test was conducted with different sheet thickness and mechanical properties. Fatigue crack initiated at underfill and pitting in the weld metal. Stress concentration factor and hardness of the weld metal were considered to estimate fatigue limit. However, hardness of the weld metal has no significant effect on fatigue strength. As a result, fatigue strength was well estimated by hardness of base metal and stress concentration factor calculated from the shape of underflll and pitting. 7 refs., 9 figs., 5 tabs.

Eggshell membrane hydrolyzates activate NF-κB in vitro: possible implications for in vivo efficacy

Directory of Open Access Journals (Sweden)

Ruff KJ

2015-02-01

Full Text Available Kevin J Ruff,1 Paul L Durham,2 Austin O’Reilly,2 F Daniel Long1 1ESM Technologies, LLC, Carthage, MO, USA; 2Center for Biomedical and Life Sciences, Missouri State University, Springfield, MO, USA Purpose: Eggshell membrane (ESM has been shown to contain naturally occurring bioactive components, and biological activities such as reducing proinflammatory cytokines, liver fibrosis, and joint pain in osteoarthritis sufferers have also been reported for ESM matrix as a whole. Nuclear factor kappa-light-chain-enhancer of activated B-cells (NF-κB is a signaling protein found in the cytoplasm of nearly all human and animal cell types and is a primary regulator of immune function. The studies reported herein were designed to investigate the possible role that NF-κB activity might play in the reported biological activities of ESM. Methods: Three ESM hydrolyzates produced via fermentation, enzymatic, or chemical hydrolysis were evaluated in vitro in either human peripheral blood mononuclear cell or THP-1 (human leukemic monocyte cell cultures for NF-κB activity following 4-hour exposure. The hydrolyzates were compared with untreated control cells or cells incubated with lipopolysaccharide or ascorbic acid. The source of ESM activity was also evaluated. Results: NF-κB levels were increased above levels found in untreated cells at all three dilutions (1:100, 1:1,000, and 1:10,000 for the fermentation hydrolyzate of ESM (ESM-FH (P=0.021, P=0.020, P=0.009, respectively in peripheral blood mononuclear cells. The enzymatic hydrolyzate of ESM (ESM-EH also produced statistically significant levels of activated NF-κB at the 1:100 and 1:1,000 dilutions (P=0.004, P=0.006, respectively but fell just shy of significance at the 1:10,000 dilution (P=0.073. Similarly, ESM-FH (P=0.021, P=0.002 and ESM-EH (P=0.007, P=0.007 activated NF-κB in THP-1 cells at 1:1,000 and 1:10,000 dilutions, respectively. The chemical hydrolyzate of ESM (ESM-CH showed statistically

High-strength high-conductivity Cu-Nb microcomposite sheet fabricated via multiple roll bonding

International Nuclear Information System (INIS)

Jha, S.C.; Delagi, R.G.; Forster, J.A.; Krotz, P.D.

1993-01-01

Copper-niobium microcomposites are a new class of high-strength high-conductivity materials that have attractive properties for room- and elevated-temperature applications. Since Nb has little solid solubility in Cu, addition of Nb to Cu does not affect its conductivity. Copper-niobium microcomposites are melted and cast so that the microstructure of cast Cu-Nb ingots consists of 1- to 10 μm Nb dendrites uniformly distributed within the copper matrix. Extensive wire drawing with a true processing strain (η> 12) of Cu-Nb alloy leads to refinement and elongation of Nb dendrites into 1- to 10 nm-thick filaments. The presence of such fine Nb filaments causes a significant increase in the strength of Cu-Nb wires. The tensile strength of heavily drawn Cu-Nb wires was determined to be significantly higher than the values predicted by the rule of mixtures. This article reports the fabrication of high-strength Cu-Nb microcomposite sheet by multiple roll bonding. It is difficult and impractical to attain high processing strains (η>3) by simple cold rolling. In most practical cold-rolling operation, the thickness reduction does not exceed 90 pct (η ≅2). Therefore, innovative processing is required to generate high strength in Cu-Nb microcomposite sheet. Multiple roll bonding of Cu-Nb has been utilized to store high processing strain ( η>10) in the material and refine the Nb particle size within the copper matrix. This article describes the microstructure, mechanical properties, and thermal stability of roll-bonded Cu-Nb microcomposite sheet

Plasmonic hybrid nanostructure with controlled interaction strength

Science.gov (United States)

Grzelak, Justyna K.; Krajnik, Bartosz; Thoreson, Mark D.; Nyga, Piotr; Shalaev, Vladimir M.; Mackowski, Sebastian

2014-03-01

In this report we discuss the influence of plasmon excitations in a silver island film on the fluorescence of photosynthetic complex, peridinin-chlorophyll-protein (PCP). Control of the separation between these two components is obtained by fabricating a wedge layer of silica across the substrate, with a thickness from 0 to 46 nm. Continuous variation of the silica thickness allows for gradual change of interaction strength between plasmon excitations in the metallic film and the excited states of pigments comprising photosynthetic complexes. While the largest separation between the silver film and photosynthetic complexes results in fluorescence featuring a mono-exponential decay and relatively narrow distribution of intensities, the PCP complexes placed on thinner silica spacers show biexponential fluorescence decay and significantly broader distribution of total fluorescence intensities. This broad distribution is a signature of stronger sensitivity of fluorescence enhancement upon actual parameters of a hybrid nanostructure. By gradual change of the silica spacer thickness we are able to reproduce classical distance dependence of fluorescence intensity in plasmonic hybrid nanostructures on ensemble level. Experiments carried out for different excitation wavelengths indicate that the interaction is stronger for excitations resonant with plasmon absorption in the metallic layer.

Investigations of Thickness Requirement in DNV Rules for High-Speed Craft

DEFF Research Database (Denmark)

Pedersen, Preben Terndrup; Zhang, Shengming

1997-01-01

Simple formulas for determining impact strength of high-speed craft collisions with floating objects are given in this note. Thereby the minimum mass of a floating object that just ruptures the shell plating is predicted. The minimum thickness requirements of DNV rules for aluminiumcrafts and GRP...... single skin crafts can be converted to critical impact energy and minimum object mass. Some comparisons show an acceptable agreement between present method and DNV test results....

Effects of blood contamination on resin-resin bond strength.

Science.gov (United States)

Eiriksson, Sigurdur O; Pereira, Patricia N R; Swift, Edward J; Heymann, Harald O; Sigurdsson, Asgeir

2004-02-01

Incremental placement and curing of resin composites has been recommended. However, this requires longer operating time, and therefore, increased risk of contamination. The purpose of this study was to evaluate the effects of blood contamination on microtensile bond strengths (microTBS) between resin interfaces and to determine the best decontamination method to re-establish the original resin-resin bond strength. The top surfaces of 64, 4-mm composite blocks (Z-250, Renew, APX, Pertac II) were untreated as the control, or were treated as follows: blood applied and dried on the surface (Treatment 1), blood applied, rinsed, dried (Treatment 2), blood applied, rinsed, and an adhesive applied (Single Bond, One-Step, Clearfil SE, Prompt L-Pop) (Treatment 3). Fresh composite was applied and light-cured in 2-mm increments. After 24 h storage in water, the specimens were sectioned into 0.7-mm thick slabs, trimmed to a cross-sectional area of 1 mm(2), and loaded to failure at a crosshead speed of 1 mm/min using an Instron universal testing machine. Data were analyzed using two-way ANOVA and Fisher's PLSD test (pcontamination resulted in resin-resin bond strengths of only 1.0-13.1 MPa. Rinsing raised bond strengths to over 40 MPa for each material. Use of an adhesive further increased bond strengths except for Pertac II. Rinsing blood from contaminated surfaces increases the resin-resin bond strength significantly and the application of an appropriate adhesive increases the bond strength to control levels.

Enamel and dentin bond strength following gaseous ozone application.

Science.gov (United States)

Cadenaro, Milena; Delise, Chiara; Antoniollo, Francesca; Navarra, Ottavia Chiara; Di Lenarda, Roberto; Breschi, Lorenzo

2009-08-01

To evaluate the effects of gaseous ozone application on enamel and dentin bond strength produced by two self-etching adhesive systems. The shear bond strength test was conducted to assess adhesion on enamel (protocol 1), while the microtensile bond strength test was performed on dentin (protocol 2). Protocol 1: 96 bovine incisors were randomly divided into 4 groups, and enamel surfaces were bonded in accordance with the following treatments: (1E) ozone + Clearfil Protect Bond; (2E) Clearfil Protect Bond (control); (3E) ozone + Xeno III; (4E) Xeno III (control). Ozone gas was applied for 80 s. Shear bond strength was measured with a universal testing machine. Protocol 2: 40 noncarious human molars were selected. Middle/deep dentin was exposed and bonded in accordance with the following treatments: (1D) ozone+Clearfil Protect Bond; (2D) Clearfil Protect Bond (control); (3D) ozone+Xeno III (4D) Xeno III (control). Four-mm-thick buildups were built on the adhesives, then specimens were sectioned in accordance with the nontrimming technique. Specimens were stressed until failure occurred, and failure modes were analyzed. Shear bond and microtensile bond strength data were analyzed using two-way ANOVA and Tukey's post-hoc test. No statistical differences were found between ozone treated specimens and controls, neither on enamel nor on dentin irrespective of the tested adhesive. Clearfil Protect Bond showed higher bond strength to enamel than Xeno III, irrespective of the ozone treatment (p enamel and dentin bond strength.

Ultrasonic-assisted production of biodiesel from transesterification of palm oil over ostrich eggshell-derived CaO catalysts.

Science.gov (United States)

Chen, Guanyi; Shan, Rui; Shi, Jiafu; Yan, Beibei

2014-11-01

In this study, waste ostrich eggshell-derived calcium oxide (denoted as CaO(OE)) particles were synthesized and explored as cost-effective catalysts for the ultrasonic-assisted transesterification of palm oil. The physicochemical properties of the resultant catalysts were characterized by XRD, N2 adsorption, XRF and Hammett indicator, while the catalytic activity was evaluated through transesterification of palm oil with methanol under ultrasonic conditions. More specifically, the CaO(OE) showed comparable catalytic activity to the one derived from commercial calcium carbonate (denoted as CaO(Lab)). Moreover, under ultrasonic conditions, the catalytic activity of CaO(OE) could be enhanced significantly. The maximum yield of fatty acid methyl esters could reach 92.7% under the optimal condition of reaction time of 60 min with ultrasonic power of 60% (120 W), methanol-to-oil ratio of 9:1, and catalyst loading of 8 wt.%. The results indicated that the CaO(OE) catalysts showed good catalytic performance and reusability, and may potentially reduce the cost of biodiesel production. Copyright © 2014 Elsevier Ltd. All rights reserved.

Effect of surface decarburization on the mechanical properties of high strength low alloy steel

International Nuclear Information System (INIS)

Saqib, S.

1993-01-01

An attempt has been made to study the relationship of mechanical properties with the microstructure of a high strength low alloy steel. A thorough investigation was conducted on the steel sheet and variation in mechanical properties was observed across its thickness with a change in the microstructure. Change in hardness and tensile strength at the surface compare to the core of the material is attributed to decarburization. The current research indicates that the correlation between hardness and tensile strength is not valid for steels if the hardness is determined on the surface only. Great care should be taken at the time of determination of tensile strength by using conversion charts/tables on the basis of hardness values obtained by practical means. (author)

The role of surface preparation in corrosion protection of copper with nanometer-thick ALD alumina coatings

Energy Technology Data Exchange (ETDEWEB)

Mirhashemihaghighi, Shadi; Światowska, Jolanta [PSL Research University, CNRS – Chimie ParisTech, Institut de Recherche de Chimie Paris (IRCP), 11 rue Pierre et Marie Curie, 75005 Paris (France); Maurice, Vincent, E-mail: vincent.maurice@chimie-paristech.fr [PSL Research University, CNRS – Chimie ParisTech, Institut de Recherche de Chimie Paris (IRCP), 11 rue Pierre et Marie Curie, 75005 Paris (France); Seyeux, Antoine; Klein, Lorena H. [PSL Research University, CNRS – Chimie ParisTech, Institut de Recherche de Chimie Paris (IRCP), 11 rue Pierre et Marie Curie, 75005 Paris (France); Salmi, Emma; Ritala, Mikko [Laboratory of Inorganic Chemistry, Department of Chemistry, University of Helsinki, P.O. Box 55, FIN-00014 Helsinki (Finland); Marcus, Philippe [PSL Research University, CNRS – Chimie ParisTech, Institut de Recherche de Chimie Paris (IRCP), 11 rue Pierre et Marie Curie, 75005 Paris (France)

2016-11-30

Highlights: • 10–50 nm thick alumina coatings were grown on copper by atomic layer deposition. • Surface smoothening by substrate annealing was studied as pre-deposition treatment. • Corrosion protection is promoted by pre-treatment for 10 nm but not for thicker films. • Local adhesion failure is assigned to the stresses accumulated in the thicker films. • Surface smoothening decreases the interfacial strength bearing the film stresses. - Abstract: Surface smoothening by substrate annealing was studied as a pre-treatment for improving the corrosion protection provided to copper by 10, 20 and 50 nm thick alumina coatings deposited by atomic layer deposition. The interplay between substrate surface state and deposited film thickness for controlling the corrosion protection provided by ultrathin barrier films is demonstrated. Pre-annealing at 750 °C heals out the dispersed surface heterogeneities left by electropolishing and reduces the surface roughness to less than 2 nm independently of the deposited film thickness. For 10 nm coatings, substrate surface smoothening promotes the corrosion resistance. However, for 20 and 50 nm coatings, it is detrimental to the corrosion protection due to local detachment of the deposited films. The weaker adherence of the thicker coatings is assigned to the stresses accumulated in the films with increasing deposited thickness. Healing out the local heterogeneities on the substrate surface diminishes the interfacial strength that is bearing the stresses of the deposited films, thereby increasing adhesion failure for the thicker films. Pitting corrosion occurs at the local sites of adhesion failure. Intergranular corrosion occurs at the initially well coated substrate grain boundaries because of the growth of a more defective and permeable coating at grain boundaries.

Influence of cement film thickness on the retention of implant-retained crowns.

Science.gov (United States)

Mehl, Christian; Harder, Sönke; Steiner, Martin; Vollrath, Oliver; Kern, Matthias

2013-12-01

The main goal of this study was to establish a new, high precision procedure to evaluate the influence of cement film thickness on the retention of cemented implant-retained crowns. Ninety-six tapered titanium abutments (6° taper, 4.3 mm diameter, Camlog) were shortened to 4 mm. Computer-aided design was used to design the crowns, and selective laser sintering, using a cobalt-chromium alloy, was used to produce the crowns. This method used a focused high-energy laser beam to fuse a localized region of metal powder to build up the crowns gradually. Before cementing, preset cement film thicknesses of 15, 50, 80, or 110 μm were established. Glass ionomer, polycarboxylate, or resin cements were used for cementation. After 3 days storage in demineralized water, the retention of the crowns was measured in tension using a universal testing machine. The cement film thicknesses could be achieved with a high level of precision. Interactions between the factors cement and cement film thickness could be found (p ≤ 0.001). For all cements, crown retention decreased significantly between a cement film thickness of 15 and 50 μm (p ≤ 0.001). At 15 μm cement film thickness, the resin cement was the most retentive cement, followed by the polycarboxylate and then the glass ionomer cement (p ≤ 0.05). The results suggest that cement film thickness has an influence on the retentive strength of cemented implant-retained crowns. © 2013 by the American College of Prosthodontists.

Performance of High Layer Thickness in Selective Laser Melting of Ti6Al4V

Directory of Open Access Journals (Sweden)

Xuezhi Shi

2016-12-01

Full Text Available To increase building rate and save cost, the selective laser melting (SLM of Ti6Al4V with a high layer thickness (200 μm and low cost coarse powders (53 μm–106 μm at a laser power of 400 W is investigated in this preliminary study. A relatively large laser beam with a diameter of 200 μm is utilized to produce a stable melt pool at high layer thickness, and the appropriate scanning track, which has a smooth surface with a shallow contact angle, can be obtained at the scanning speeds from 40 mm/s to 80 mm/s. By adjusting the hatch spacings, the density of multi-layer samples can be up to 99.99%, which is much higher than that achieved in previous studies about high layer thickness selective laser melting. Meanwhile, the building rate can be up to 7.2 mm3/s, which is about 2 times–9 times that of the commercial equipment. Besides, two kinds of defects are observed: the large un-melted defects and the small spherical micropores. The formation of the un-melted defects is mainly attributed to the inappropriate overlap rates and the unstable scanning tracks, which can be eliminated by adjusting the processing parameters. Nevertheless, the micropores cannot be completely eliminated. It is worth noting that the high layer thickness plays a key role on surface roughness rather than tensile properties during the SLM process. Although a sample with a relatively coarse surface is generated, the average values of yield strength, ultimate tensile strength, and elongation are 1050 MPa, 1140 MPa, and 7.03%, respectively, which are not obviously different than those with the thin layer thickness used in previous research; this is due to the similar metallurgical bonding and microstructure.

Performance of High Layer Thickness in Selective Laser Melting of Ti6Al4V.

Science.gov (United States)

Shi, Xuezhi; Ma, Shuyuan; Liu, Changmeng; Chen, Cheng; Wu, Qianru; Chen, Xianping; Lu, Jiping

2016-12-01

To increase building rate and save cost, the selective laser melting (SLM) of Ti6Al4V with a high layer thickness (200 μm) and low cost coarse powders (53 μm-106 μm) at a laser power of 400 W is investigated in this preliminary study. A relatively large laser beam with a diameter of 200 μm is utilized to produce a stable melt pool at high layer thickness, and the appropriate scanning track, which has a smooth surface with a shallow contact angle, can be obtained at the scanning speeds from 40 mm/s to 80 mm/s. By adjusting the hatch spacings, the density of multi-layer samples can be up to 99.99%, which is much higher than that achieved in previous studies about high layer thickness selective laser melting. Meanwhile, the building rate can be up to 7.2 mm³/s, which is about 2 times-9 times that of the commercial equipment. Besides, two kinds of defects are observed: the large un-melted defects and the small spherical micropores. The formation of the un-melted defects is mainly attributed to the inappropriate overlap rates and the unstable scanning tracks, which can be eliminated by adjusting the processing parameters. Nevertheless, the micropores cannot be completely eliminated. It is worth noting that the high layer thickness plays a key role on surface roughness rather than tensile properties during the SLM process. Although a sample with a relatively coarse surface is generated, the average values of yield strength, ultimate tensile strength, and elongation are 1050 MPa, 1140 MPa, and 7.03%, respectively, which are not obviously different than those with the thin layer thickness used in previous research; this is due to the similar metallurgical bonding and microstructure.

Study of the thickness evolution during SPT Testing

Directory of Open Access Journals (Sweden)

David Sánchez-Ávila

2018-03-01

Full Text Available The Small Punch Test (SPT is an increasingly expanding test used to obtain different mechanical data, such as strength, fracture, creep, etc…especially when there is little material available. However, the SPT test is more complicated than the uniaxial tensile test due to its non-linearity, which makes it difficult to relate the data obtained with the tensile tests. In fact, in the literature there is no clear model linking these tests and a different calibration should be used for each material. The complication of the SPT test is that the reduction of the sample thickness is not homogeneous in its gauge volume. In this work we proceeded to determine the variation of the SPT specimen thickness at several points, especially at the center and at the rupture zone, by means of the use of finite elements in COMSOL, taking a SLM AM (selective laser melting additive manufactured 316L stainless steel as the base material for modelling. For the appropriate modelling in COMSOL, the mechanical parameters of two 316L extreme thermomechanical treatments have been implemented, one annealed to a minimum hardness and another heavily work-hardened. The sample thickness variation results allow advancing in the theoretical modeling of the SPT behavior in order to obtain more accurate correlations with tensile tests data.

Effects of a Modified German Volume Training Program on Muscular Hypertrophy and Strength.

Science.gov (United States)

Amirthalingam, Theban; Mavros, Yorgi; Wilson, Guy C; Clarke, Jillian L; Mitchell, Lachlan; Hackett, Daniel A

2017-11-01

Amirthalingam, T, Mavros, Y, Wilson, GC, Clarke, JL, Mitchell, L, and Hackett, DA. Effects of a modified German volume training program on muscular hypertrophy and strength. J Strength Cond Res 31(11): 3109-3119, 2017-German Volume Training (GVT), or the 10 sets method, has been used for decades by weightlifters to increase muscle mass. To date, no study has directly examined the training adaptations after GVT. The purpose of this study was to investigate the effect of a modified GVT intervention on muscular hypertrophy and strength. Nineteen healthy men were randomly assign to 6 weeks of 10 or 5 sets of 10 repetitions for specific compound resistance exercises included in a split routine performed 3 times per week. Total and regional lean body mass, muscle thickness, and muscle strength were measured before and after the training program. Across groups, there were significant increases in lean body mass measures, however, greater increases in trunk (p = 0.043; effect size [ES] = -0.21) and arm (p = 0.083; ES = -0.25) lean body mass favored the 5-SET group. No significant increases were found for leg lean body mass or measures of muscle thickness across groups. Significant increases were found across groups for muscular strength, with greater increases in the 5-SET group for bench press (p = 0.014; ES = -0.43) and lat pull-down (p = 0.003; ES = -0.54). It seems that the modified GVT program is no more effective than performing 5 sets per exercise for increasing muscle hypertrophy and strength. To maximize hypertrophic training effects, it is recommended that 4-6 sets per exercise be performed, as it seems gains will plateau beyond this set range and may even regress due to overtraining.

Effects of Strength vs. Ballistic-Power Training on Throwing Performance.

Science.gov (United States)

Zaras, Nikolaos; Spengos, Konstantinos; Methenitis, Spyridon; Papadopoulos, Constantinos; Karampatsos, Giorgos; Georgiadis, Giorgos; Stasinaki, Aggeliki; Manta, Panagiota; Terzis, Gerasimos

2013-01-01

The purpose of the present study was to investigate the effects of 6 weeks strength vs. ballistic-power (Power) training on shot put throwing performance in novice throwers. Seventeen novice male shot-put throwers were divided into Strength (N = 9) and Power (n = 8) groups. The following measurements were performed before and after the training period: shot put throws, jumping performance (CMJ), Wingate anaerobic performance, 1RM strength, ballistic throws and evaluation of architectural and morphological characteristics of vastus lateralis. Throwing performance increased significantly but similarly after Strength and Power training (7.0-13.5% vs. 6.0-11.5%, respectively). Muscular strength in leg press increased more after Strength than after Power training (43% vs. 21%, respectively), while Power training induced an 8.5% increase in CMJ performance and 9.0 - 25.8% in ballistic throws. Peak power during the Wingate test increased similarly after Strength and Power training. Muscle thickness increased only after Strength training (10%, p ballistic power training in novice throwers, but with dissimilar muscular adaptations. Key pointsBallistic-power training with 30% of 1RM is equally effective in increasing shot put performance as strength training, in novice throwers, during a short training cycle of six weeks.In novice shot putters with relatively low initial muscle strength/mass, short-term strength training might be more important since it can increase both muscle strength and shot put performance.The ballistic type of power training resulted in a significant increase of the mass of type IIx muscle fibres and no change in their proportion. Thus, this type of training might be used effectively during the last weeks before competition, when the strength training load is usually reduced, in order to increase muscle power and shot put performance in novice shot putters.

Fatigue testing of weldable high strength steels under simulated service conditions

Science.gov (United States)

Tantbirojn, Natee

There have been concerns over the effect of Cathodic Protection (CP) on weldable high strength steels employed in Jack-up production platform. The guidance provided by the Department of Energy HSE on higher strength steels, based on previous work, was to avoid overprotection as this could cause hydrogen embrittlement. However, the tests conducted so far at UCL for the SE702 type high strength steels (yields strength around 690 MPa) have shown that the effect of over protection on high strength steels may not be as severe as previously thought. For this thesis, SE702 high strength steels have been investigated in more detail. Thick (85mm) parent and ground welded plates were tested under constant amplitude in air and seawater with CP. Tests were also conducted on Thick (40mm) T-butt welded plates under variable amplitude loading in air and seawater with two CP levels (-800mV and -1050mV). Different backing materials (ceramic and metallic) for the welding process of the T-butt plates were also investigated. The variable amplitude sequences employed were generated using the Jack-up Offshore Standard load History (JOSH). The fatigue results are presented as crack growth and S/N curves. They were compared to the conventional offshore steel (BS 4360 50D). The results suggested that the fatigue life of the high strength steels was comparable to the BS 4360 50D steels. The effect of increasing the CP was found to be detrimental to the fatigue life but the effect was not large. The effect of CP was less noticeable in T-butt welded plates. However, in general, the effect of overprotection is not as detrimental to the Jack-up steels as previously thought. The load histories generated by JOSH were found to have some unfavourable characteristics. The framework is based on Markov Chain method and pseudo-random number generator for selecting sea-states. A study was carried out on the sequence generated by JOSH. The generated sequences were analysed for their validity for fatigue

Influence of earlobe thickness on near infrared spectroscopy

Science.gov (United States)

Jiang, Jingying; Wang, Tianpei; Li, Si; Li, Lin; Liu, Jiajia; Xu, Kexin

2017-03-01

Near-infrared spectroscopy has been recognized as a potential technology for noninvasive blood glucose sensing. However, the detected spectral signal is unstable mainly because of (1) the weak light absorption of glucose itself within NIR range, (2) the influence of temperature and individual differences of biotissue. Our previous results demonstrated that the synergistic effect of both transmittance and reflectance could enhance the strength of the detection signal. In this talk, we design a set of experiments to analyze the effect of earlobe thickness on Near Infrared spectroscopic measurement by using home-made optical fiber probe within the wavelength of 1000-1600nm. Firstly, we made a MC simulation of single-layer skin model and five-layer skin model to get the diffused transmittance spectra and diffused reflectance spectra under different optaical path lengths. And then we obtain the spectra of the earlobes from different volunteers by the same way. The experimental results showed that with the increase of the thickness,the light intensity of diffused transmittance decreases, and the light intensity of diffused reflectance remaines substantially unchanged.

Towards developing product applications of thick origami using the offset panel technique

Directory of Open Access Journals (Sweden)

M. R. Morgan

2016-03-01

Full Text Available Several methods have been developed to accommodate for the use of thick materials in origami models which preserve either the model's full range of motion or its kinematics. The offset panel technique (OPT preserves both the range of motion and the kinematics while allowing for a great deal of flexibility in design. This work explores new possibilities for origami-based product applications presented by the OPT. Examples are included to illustrate fundamental capabilities that can be realized with thick materials such as accommodation of various materials in a design and manipulation of panel geometry resulting in an increased stiffness and strength. These capabilities demonstrate the potential of techniques such as the OPT to further inspire origami-based solutions to engineering problems.

Fragmentation of spin-dipole strength in {sup 90}Zr and {sup 208}Pb

Energy Technology Data Exchange (ETDEWEB)

Marketin, T., E-mail: marketin@phy.hr [GSI Helmholtzzentrum fuer Schwerionenforschung, Planckstrasse 1, D-64291 Darmstadt (Germany); Physics Department, Faculty of Science, University of Zagreb, 10000 Zagreb (Croatia); Litvinova, E. [ExtreMe Matter Institute EMMI and Research Division, GSI Helmholtzzentrum fuer Schwerionenforschung, Planckstrasse 1, D-64291 Darmstadt (Germany); Vretenar, D. [Physics Department, Faculty of Science, University of Zagreb, 10000 Zagreb (Croatia); Ring, P. [Physik-Department der Technischen Universitaet Muenchen, D-85748 Garching (Germany)

2012-01-05

An extension of time-dependent covariant density functional theory that includes particle-vibration coupling is applied to the charge-exchange channel. Spin-dipole excitation spectra are calculated an compared to available data for {sup 90}Zr and {sup 208}Pb. A significant fragmentation is found for all three angular-momentum components of the spin-dipole strength as a result of particle-vibration coupling, as well as a shift of a portion of the strength to higher energy. A high-energy tail is formed in the strength distribution that linearly decreases with energy. Using a model-independent sum rule, the corresponding neutron skin thickness is estimated and shown to be consistent with values obtained at the mean-field level.

Optimization of Biodiesel Production from Waste Cooking Oil Using Waste Eggshell as a Base Catalyst under a Microwave Heating System

Directory of Open Access Journals (Sweden)

Yen-Ping Peng

2018-02-01

Full Text Available This paper intends to explore the most affordable and environmentally friendly method for the synthesis of biodiesel. Substitute fuel is presently a significant topic all over the world, attributable to the efforts of reducing global warming, which is the result arising from the combustion of petroleum or petrol diesel fuel. Due to its advantages of being renewable and environmentally friendly, biodiesel production has the potential to become the major substitute of petrol diesel fuel. Biodiesel is non-toxic, biodegradable, is produced from renewable sources, and contributes a small amount of greenhouse gas (e.g., CO2 and SO2 emissions to the atmosphere. Research has established that one of the key obstacles to the commercialization of biodiesel is the high price of biodiesel production due to the shortage of suitable raw materials. However, waste-cooking-oil (WCO is one of the most cost-effective sources of biodiesel synthesis, and can practically minimize the raw material cost. The research was carried out to produce biodiesel from waste cooking oil in order to reduce the cost, waste, and pollution associated with biodiesel production. The application of a microwave heating system towards enhancing the production of biodiesel from waste cooking oil has been given little consideration in the preceding research, particularly with the application of eggshell as a heterogeneous catalyst. However, the tentative results in this study show significant performance in terms of biodiesel production, as follows: (1 the increasing of the reaction time from 120 to 165 min considerably increased the biodiesel production, which declined with a further rise to 210 min; (2 the results of this study reveal that a methanol-to-oil molar ratio of nine is appropriate and can be used for the best production of biodiesel; (3 the production of biodiesel in this study demonstrated a significant increase in response to the further increasing of power; (4 a 120 min

Modulation of spin-orbit torque efficiency by thickness control of heavy metal layers in Co/Pt multilayers

Energy Technology Data Exchange (ETDEWEB)

Sethi, P.; Krishnia, S.; Li, S.H.; Lew, W.S., E-mail: wensiang@ntu.edu.sg

2017-03-15

We investigate and quantify spin-orbit torque (SOT) strength by current induced effective in-plane magnetic fields and spin Hall angle (SHA) using AC harmonic Hall voltage measurements techniques on Ta/Pt/Co/Pt/Co/Ta thin film structures. The proposed Co/Pt thin film double stack gives property enhancement on thermal stability and perpendicular magnetization anisotropy strength over the single stack Pt/Co/Ta. In the proposed Co/Pt double stack we observed that increasing the Ta capping thickness to three times enhances the SHA in similar order, consistent with larger spin injection efficiency. Doubling the Pt spacer layer thickness reduces the SHA by nearly 1.4 times, due to partial cancellation of SOT by bottom layer Pt, negating the increase from the top Co/Pt interface. The in-plane current threshold for magnetization switching is lower with the increase of the SHA.

Stiffness, strength and adhesion characterization of electrochemically deposited conjugated polymer films

Science.gov (United States)

Qu, Jing; Ouyang, Liangqi; Kuo, Chin-chen; Martin, David C.

2015-01-01

Conjugated polymers such as poly(3,4-ethylenedioxythiphene) (PEDOT) are of interest for a variety of applications including interfaces between electronic biomedical devices and living tissue. The mechanical properties, strength, and adhesion of these materials to solid substrates are all vital for long-term applications. We have been developing methods to quantify the mechanical properties of conjugated polymer thin films. In this study the stiffness, strength and the interfacial shear strength (adhesion) of electrochemically deposited PEDOT and PEDOT-co-1,3,5-tri[2-(3,4-ethylene dioxythienyl)]-benzene (EPh) were studied. The estimated Young’s modulus of the PEDOT films was 2.6 ± 1.4 GPa, and the strain to failure was around 2%. The tensile strength was measured to be 56 ± 27 MPa. The effective interfacial shear strength was estimated with a shear-lag model by measuring the crack spacing as a function of film thickness. For PEDOT on gold/palladium-coated hydrocarbon film substrates an interfacial shear strength of 0.7 ± 0.3 MPa was determined. The addition of 5 mole% of a tri-functional EDOT crosslinker (EPh) increased the tensile strength of the films to 283 ± 67 MPa, while the strain to failure remained about the same (2%). The effective interfacial shear strength was increased to 2.4 ± 0.6 MPa. PMID:26607768

Solar cell contact pull strength as a function of pull-test temperature

Science.gov (United States)

Yasui, R. K.; Berman, P. A.

1972-01-01

Four types of solar cell contacts were given pull-strength tests at temperatures between -173 and +165 C. Contacts tested were: (1) solder-coated titanium-silver contacts on n-p cells, (2) palladium-containing titanium-silver contacts on n-p cells, (3) titanium-silver contacts on 0.2-mm-thick n-p cells, and (4) solder-coated electroless-nickel-plated contacts on p-n cells. Maximum pull strength was demonstrated at temperatures significantly below the air mass zero cell equilibrium temperature of +60 C. At the lowest temperatures, the chief failure mechanism was silicon fracture along crystallographic planes; at the highest temperatures, it was loss of solder strength. In the intermediate temperatures, many failure mechanisms operated. Pull-strength tests give a good indication of the suitability of solar cell contact systems for space use. Procedures used to maximize the validity of the results are described.

Effect of friction stir lap welding conditions on joint strength of aluminium alloy 6060

International Nuclear Information System (INIS)

Yazdanian, S; Chen, Z W

2009-01-01

Strength of lap joints made by friction stir welding (FSW) depends strongly on how material flows forming the weld nugget zone during FSW and also on how the joint is loaded during testing. Understanding of this processing-property relationship is currently inadequate. In this study, the effects of pin length, welding speed and rotation rate on weld strength using aluminium alloy 6060 were investigated. It has been found that the pin length needed to be slightly greater than the thickness of the sheet for an adequate joint to be established. However, further increase in pin length did not benefit the joint strength. The major factor affecting joint strength has been found to be the rotation speed. An increase in rotation speed resulted in lowering the joint strength. Various modes of fracture have been observed and these modes relate to the degree of hooking and softening. Explanation of how the speed values relate to heat input and material flow and then to the joint strength is given.

Influence of Thickness Variation on the Flapping Performance of Symmetric NACA Airfoils in Plunging Motion

Directory of Open Access Journals (Sweden)

Liangyu Zhao

2010-01-01

Full Text Available In order to investigate the impact of airfoil thickness on flapping performance, the unsteady flow fields of a family of airfoils from an NACA0002 airfoil to an NACA0020 airfoil in a pure plunging motion and a series of altered NACA0012 airfoils in a pure plunging motion were simulated using computational fluid dynamics techniques. The “class function/shape function transformation“ parametric method was employed to decide the coordinates of these altered NACA0012 airfoils. Under specified plunging kinematics, it is observed that the increase of an airfoil thickness can reduce the leading edge vortex (LEV in strength and delay the LEV shedding. The increase of the maximum thickness can enhance the time-averaged thrust coefficient and the propulsive efficiency without lift reduction. As the maximum thickness location moves towards the leading edge, the airfoil obtains a larger time-averaged thrust coefficient and a higher propulsive efficiency without changing the lift coefficient.

Quantum transition and decoherence of levitating polaron on helium film thickness under an electromagnetic field

Science.gov (United States)

Kenfack, S. C.; Fotue, A. J.; Fobasso, M. F. C.; Djomou, J.-R. D.; Tiotsop, M.; Ngouana, K. S. L.; Fai, L. C.

2017-12-01

We have studied the transition probability and decoherence time of levitating polaron in helium film thickness. By using a variational method of Pekar type, the ground and the first excited states of polaron are calculated above the liquid-helium film placed on the polar substrate. It is shown that the polaron transits from the ground to the excited state in the presence of an external electromagnetic field in the plane. We have seen that, in the helium film, the effects of the magnetic and electric fields on the polaron are opposite. It is also shown that the energy, transition probability and decoherence time of the polaron depend sensitively on the helium film thickness. We found that decoherence time decreases as a function of increasing electron-phonon coupling strength and the helium film thickness. It is seen that the film thickness can be considered as a new confinement in our system and can be adjusted in order to reduce decoherence.

Purification and characterization of an eggshell membrane decomposing protease from Pseudomonas aeruginosa strain ME-4.

Science.gov (United States)

Cheng, Minyi; Takenaka, Shinji; Aoki, Shunsuke; Murakami, Shuichiro; Aoki, Kenji

2009-04-01

A bacterial strain, ME-4, isolated from farm soil and identified as Pseudomonas aeruginosa, grew well on a medium containing eggshell membrane (ESM). P. aeruginosa strain ME-4 decomposed the ESM by producing an extracellular protease able to solubilize it. The protease was purified to homogeneity from culture supernatant by fractionation with (NH(4))(2)SO(4), as well as CM52 cellulose and DE52 cellulose column chromatography, with a final yield of 47%. The molecular mass of the enzyme was 33 kDa. The isolated enzyme was a metalloprotease and was strongly inhibited by EDTA, o-phenanthroline, and phosphoramidon. The enzyme inhibited by these reagents was reactivated in the presence of several metal ions. The enzyme acted on various proteins and showed higher activity with collagen than collagenase from Clostridium histolyticum. Results of assays with the FRETS combinatorial libraries revealed that the enzyme preferred Ser at the P1 position and Lys at the P2 position. It also preferred hydrophobic amino acid residues at the P1' and P2' positions. The enzyme showed a much higher solubilization activity with the ESM substrate than commercially obtained enzymes. The enzyme decomposed ESM to produce water-soluble peptides, Val-Leu-Pro-Pro and (X)-Val-Pro-Pro, and a free amino acid, tryptophan.

Shear bond strength of indirect composite material to monolithic zirconia.

Science.gov (United States)

Sari, Fatih; Secilmis, Asli; Simsek, Irfan; Ozsevik, Semih

2016-08-01

This study aimed to evaluate the effect of surface treatments on bond strength of indirect composite material (Tescera Indirect Composite System) to monolithic zirconia (inCoris TZI). Partially stabilized monolithic zirconia blocks were cut into with 2.0 mm thickness. Sintered zirconia specimens were divided into different surface treatment groups: no treatment (control), sandblasting, glaze layer & hydrofluoric acid application, and sandblasting + glaze layer & hydrofluoric acid application. The indirect composite material was applied to the surface of the monolithic zirconia specimens. Shear bond strength value of each specimen was evaluated after thermocycling. The fractured surface of each specimen was examined with a stereomicroscope and a scanning electron microscope to assess the failure types. The data were analyzed using one-way analysis of variance (ANOVA) and Tukey LSD tests (α=.05). Bond strength was significantly lower in untreated specimens than in sandblasted specimens (Pcomposite material and monolithic zirconia.

Impact resistance and interlaminar fracture toughness of through-the-thickness reinforced graphite/epoxy

Science.gov (United States)

Dexter, H. B.; Funk, J. G.

1986-01-01

Five through-the-thickness stitch configurations are analyzed to determine the effect of impact resistance and interlaminar fracture toughness on T3000/3501-6 graphite/epoxy. The test specimens were stitched with either polyester or Kevlar yarns and with various stitch parameters. Tension and compression mechanical, impact and compression-after-impact, and double cantilever beam tests were conducted. It is observed that the stitched laminates have tension and compression strengths 20-25 percent lower than the strengths of unstitched laminates, the tension strength of stitched laminates is reduced with increasing number of stitches, and the compression strength increases as the number of stitches are increased. The impact data reveal that the Kevlar stitched laminates have less damage than unstitched laminates; the most effective configuration for suppressing impact damage and improving interlaminar fracture toughness consists of Kevlar yarns 1/4 inch apart with eight stitches per inch. The mode 1 critical strain energy release rate for the 1/4 inch Kevlar eight stitch laminate was calculated as 30 times higher than that of the unstitched.

Effects of non-feed removal molting methods on egg quality traits in commercial brown egg laying hens in Turkey.

Science.gov (United States)

Petek, Metin; Gezen, S Sule; Alpay, Fazli; Cibik, Recep

2008-08-01

Non-feed removal molting programme in commercial brown laying hens and its influence on pre-molting, post-molting and end of cycle egg quality traits were investigated. Overall 54 birds were randomly divided into three treatment groups and each group was fed with one of the following diets during 10 days of molting period: (i) grain barley, (ii) alfalfa meal, or (iii) commercial layer ration (non-molted control group). Eggs obtained from groups in pre-molting, post-molting and end of cycle periods were examined for several quality performance traits such as egg weight, specific gravity, shape index, shell strength, shell thickness, eggshell weight, haugh unit, albumen index, yolk index and yolk color. Results indicated that non-feed removal molting programme based particularly on grain barley had positive effect on egg quality traits in laying hens. Notably, yolk color and haugh unit, which are considered as the most important quality parameters from the consumer point of view, were relatively improved in barley molted group.

Body Build and the Level of Development of Muscle Strength Among Male Jiu-Jitsu Competitors and Strength-Trained Adults

Directory of Open Access Journals (Sweden)

Pietraszewska Jadwiga

2014-09-01

Full Text Available Purpose. The aim of the present study was to assess the morpho-functional characteristics of male jiu-jitsu practitioners against a sample of strength-trained university students. Methods. The all-male research sample included 49 jiu-jitsu competitors and 30 university students actively involved in strength training. Measures of body mass and height, lower extremity length, sitting height, arm span, trunk width, skeletal breadths, circumferences and skinfold thicknesses of the trunk and extremities were collected. Body tissue composition was assessed using bioelectrical impedance analysis. Somatotype was classified according to the anthropometric method of Heath and Carter. Participants also performed three motor tests composed of the standing long jump, flexed arm hang, and sit-ups and two dynamometer tests measuring handgrip and back muscle strength. Differences between the measured characteristics in both samples were analyzed using Student’s t test. Pearson’s correlation coefficient was used to the determine the relationships between the morphological characteristics and the results of the motor tests. Results. The jiu-jitsu sample was slightly smaller than the strength-training students. In contrast, body mass was almost identical in both groups. The remaining length, height, and skinfold characteristics also did not differ significantly between the groups. Only hip breadth was significantly larger in the jiu-jitsu sample. No between-group differences were noted in the levels of endomorphy, mesomorphy, and ectomorphy. The composite somatotype of the jiu-jitsu athletes (2.1-5.8-2.0 was very similar to that of the strength-trained students (2.1-5.9-2.4. Statistically significant differences were observed in the tests assessing muscle strength. Handgrip and back muscle strength was greater in the strength-training students, whereas the jiu-jitsu athletes performed better in all three motor tests. Conclusions. The minor morphological

A novel disulfide-rich protein motif from avian eggshell membranes.

Directory of Open Access Journals (Sweden)

Vamsi K Kodali

2011-03-01

Full Text Available Under the shell of a chicken egg are two opposed proteinaceous disulfide-rich membranes. They are fabricated in the avian oviduct using fibers formed from proteins that are extensively coupled by irreversible lysine-derived crosslinks. The intractability of these eggshell membranes (ESM has slowed their characterization and their protein composition remains uncertain. In this work, reductive alkylation of ESM followed by proteolytic digestion led to the identification of a cysteine rich ESM protein (abbreviated CREMP that was similar to spore coat protein SP75 from cellular slime molds. Analysis of the cysteine repeats in partial sequences of CREMP reveals runs of remarkably repetitive patterns. Module a contains a C-X(4-C-X(5-C-X(8-C-X(6 pattern (where X represents intervening non-cysteine residues. These inter-cysteine amino acid residues are also strikingly conserved. The evolutionarily-related module b has the same cysteine spacing as a, but has 11 amino acid residues at its C-terminus. Different stretches of CREMP sequences in chicken genomic DNA fragments show diverse repeat patterns: e.g. all a modules; an alternation of a-b modules; or an a-b-b arrangement. Comparable CREMP proteins are found in contigs of the zebra finch (Taeniopygia guttata and in the oviparous green anole lizard (Anolis carolinensis. In all these cases the long runs of highly conserved modular repeats have evidently led to difficulties in the assembly of full length DNA sequences. Hence the number, and the amino acid lengths, of CREMP proteins are currently unknown. A 118 amino acid fragment (representing an a-b-a-b pattern from a chicken oviduct EST library expressed in Escherichia coli is a well folded, highly anisotropic, protein with a large chemical shift dispersion in 2D solution NMR spectra. Structure is completely lost on reduction of the 8 disulfide bonds of this protein fragment. Finally, solid state NMR spectra suggest a surprising degree of order in intact

High-strength cellular ceramic composites with 3D microarchitecture.

Science.gov (United States)

Bauer, Jens; Hengsbach, Stefan; Tesari, Iwiza; Schwaiger, Ruth; Kraft, Oliver

2014-02-18

To enhance the strength-to-weight ratio of a material, one may try to either improve the strength or lower the density, or both. The lightest solid materials have a density in the range of 1,000 kg/m(3); only cellular materials, such as technical foams, can reach considerably lower values. However, compared with corresponding bulk materials, their specific strength generally is significantly lower. Cellular topologies may be divided into bending- and stretching-dominated ones. Technical foams are structured randomly and behave in a bending-dominated way, which is less weight efficient, with respect to strength, than stretching-dominated behavior, such as in regular braced frameworks. Cancellous bone and other natural cellular solids have an optimized architecture. Their basic material is structured hierarchically and consists of nanometer-size elements, providing a benefit from size effects in the material strength. Designing cellular materials with a specific microarchitecture would allow one to exploit the structural advantages of stretching-dominated constructions as well as size-dependent strengthening effects. In this paper, we demonstrate that such materials may be fabricated. Applying 3D laser lithography, we produced and characterized micro-truss and -shell structures made from alumina-polymer composite. Size-dependent strengthening of alumina shells has been observed, particularly when applied with a characteristic thickness below 100 nm. The presented artificial cellular materials reach compressive strengths up to 280 MPa with densities well below 1,000 kg/m(3).

Chairside CAD/CAM materials. Part 2: Flexural strength testing.

Science.gov (United States)

Wendler, Michael; Belli, Renan; Petschelt, Anselm; Mevec, Daniel; Harrer, Walter; Lube, Tanja; Danzer, Robert; Lohbauer, Ulrich

2017-01-01

Strength is one of the preferred parameters used in dentistry for determining clinical indication of dental restoratives. However, small dimensions of CAD/CAM blocks limit reliable measurements with standardized uniaxial bending tests. The objective of this study was to introduce the ball-on-three-ball (B3B) biaxial strength test for dental for small CAD/CAM block in the context of the size effect on strength predicted by the Weibull theory. Eight representative chairside CAD/CAM materials ranging from polycrystalline zirconia (e.max ZirCAD, Ivoclar-Vivadent), reinforced glasses (Vitablocs Mark II, VITA; Empress CAD, Ivoclar-Vivadent) and glass-ceramics (e.max CAD, Ivoclar-Vivadent; Suprinity, VITA; Celtra Duo, Dentsply) to hybrid materials (Enamic, VITA; Lava Ultimate, 3M ESPE) have been selected. Specimens were prepared with highly polished surfaces in rectangular plate (12×12×1.2mm 3 ) or round disc (Ø=12mm, thickness=1.2mm) geometries. Specimens were tested using the B3B assembly and the biaxial strength was determined using calculations derived from finite element analyses of the respective stress fields. Size effects on strength were determined based on results from 4-point-bending specimens. A good agreement was found between the biaxial strength results for the different geometries (plates vs. discs) using the B3B test. Strength values ranged from 110.9MPa (Vitablocs Mark II) to 1303.21MPa (e.max ZirCAD). The strength dependency on specimen size was demonstrated through the calculated effective volume/surface. The B3B test has shown to be a reliable and simple method for determining the biaxial strength restorative materials supplied as small CAD/CAM blocks. A flexible solution was made available for the B3B test in the rectangular plate geometry. Copyright © 2016 The Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Lead Thickness Measurements

International Nuclear Information System (INIS)

Rucinski, R.

1998-01-01

The preshower lead thickness applied to the outside of D-Zero's superconducting solenoid vacuum shell was measured at the time of application. This engineering documents those thickness measurements. The lead was ordered in sheets 0.09375-inch and 0.0625-inch thick. The tolerance on thickness was specified to be +/- 0.003-inch. The sheets all were within that thickness tolerance. The nomenclature for each sheet was designated 1T, 1B, 2T, 2B where the numeral designates it's location in the wrap and 'T' or 'B' is short for 'top' or 'bottom' half of the solenoid. Micrometer measurements were taken at six locations around the perimeter of each sheet. The width,length, and weight of each piece was then measured. Using an assumed pure lead density of 0.40974 lb/in 3 , an average sheet thickness was calculated and compared to the perimeter thickness measurements. In every case, the calculated average thickness was a few mils thinner than the perimeter measurements. The ratio was constant, 0.98. This discrepancy is likely due to the assumed pure lead density. It is not felt that the perimeter is thicker than the center regions. The data suggests that the physical thickness of the sheets is uniform to +/- 0.0015-inch.

Research on High Layer Thickness Fabricated of 316L by Selective Laser Melting

Directory of Open Access Journals (Sweden)

Shuo Wang

2017-09-01

Full Text Available Selective laser melting (SLM is a potential additive manufacturing (AM technology. However, the application of SLM was confined due to low efficiency. To improve efficiency, SLM fabrication with a high layer thickness and fine powder was systematically researched, and the void areas and hollow powders can be reduced by using fine powder. Single-track experiments were used to narrow down process parameter windows. Multi-layer fabrication relative density can be reached 99.99% at the exposure time-point distance-hatch space of 120 μs-40 μm-240 μm. Also, the building rate can be up to 12 mm3/s, which is about 3–10 times higher than the previous studies. Three typical defects were found by studying deeply, including the un-melted defect between the molten pools, the micro-pore defect within the molten pool, and the irregular distribution of the splashing phenomenon. Moreover, the microstructure is mostly equiaxed crystals and a small amount of columnar crystals. The averages of ultimate tensile strength, yield strength, and elongation are 625 MPa, 525 MPa, and 39.9%, respectively. As exposure time increased from 80 μs to 200 μs, the grain size is gradually grown up from 0.98 μm to 2.23 μm, the grain aspect ratio is close to 1, and the tensile properties are shown as a downward trend. The tensile properties of high layer thickness fabricated are not significantly different than those with a coarse-powder layer thickness of low in previous research.

Research on High Layer Thickness Fabricated of 316L by Selective Laser Melting.

Science.gov (United States)

Wang, Shuo; Liu, Yude; Shi, Wentian; Qi, Bin; Yang, Jin; Zhang, Feifei; Han, Dong; Ma, Yingyi

2017-09-08

Selective laser melting (SLM) is a potential additive manufacturing (AM) technology. However, the application of SLM was confined due to low efficiency. To improve efficiency, SLM fabrication with a high layer thickness and fine powder was systematically researched, and the void areas and hollow powders can be reduced by using fine powder. Single-track experiments were used to narrow down process parameter windows. Multi-layer fabrication relative density can be reached 99.99% at the exposure time-point distance-hatch space of 120 μs-40 μm-240 μm. Also, the building rate can be up to 12 mm³/s, which is about 3-10 times higher than the previous studies. Three typical defects were found by studying deeply, including the un-melted defect between the molten pools, the micro-pore defect within the molten pool, and the irregular distribution of the splashing phenomenon. Moreover, the microstructure is mostly equiaxed crystals and a small amount of columnar crystals. The averages of ultimate tensile strength, yield strength, and elongation are 625 MPa, 525 MPa, and 39.9%, respectively. As exposure time increased from 80 μs to 200 μs, the grain size is gradually grown up from 0.98 μm to 2.23 μm, the grain aspect ratio is close to 1, and the tensile properties are shown as a downward trend. The tensile properties of high layer thickness fabricated are not significantly different than those with a coarse-powder layer thickness of low in previous research.

Mathematical model to compare the relative tensile strength of the cornea after PRK, LASIK, and small incision lenticule extraction.

Science.gov (United States)

Reinstein, Dan Z; Archer, Timothy J; Randleman, J Bradley

2013-07-01

To develop a mathematical model to estimate the relative differences in postoperative stromal tensile strength following photorefractive keratectomy (PRK), LASIK, and small incision lenticule extraction (SMILE). Using previously published data where in vitro corneal stromal tensile strength was determined as a function of depth, a mathematical model was built to calculate the relative remaining tensile strength by fitting the data with a fourth order polynomial function yielding a high correlation coefficient (R(2) = 0.930). Calculating the area under this function provided a measure of total stromal tensile strength (TTS), based only on the residual stromal layer for PRK or LASIK and the residual stromal layers above and below the lenticule interface for SMILE. Postoperative TTS was greatest after SMILE, followed by PRK, then LASIK; for example, in a 550-μm cornea after 100-μm tissue removal, postoperative TTS was 75% for SMILE (130-μm cap), 68% for PRK, and 54% for LASIK (110-μm flap). The postoperative TTS decreased for thinner corneal pachymetry for all treatment types. In LASIK, the postoperative TTS decreased with increasing flap thickness by 0.22%/μm, but increased by 0.08%/μm for greater cap thickness in SMILE. The model predicted that SMILE lenticule thickness could be approximately 100 μm greater than the LASIK ablation depth and still have equivalent corneal strength (equivalent to approximately 7.75 diopters). This mathematical model predicts that the postoperative TTS is considerably higher after SMILE than both PRK and LASIK, as expected given that the strongest anterior lamellae remain intact. Consequently, SMILE should be able to correct higher levels of myopia. Copyright 2013, SLACK Incorporated.