The Effect of Tempering on Strength Properties and Seed Coat ...

African Journals Online (AJOL)

The effect of tempering on seed coat adhesion strength and mechanical strength of sorghum and millet grain kernels was investigated at different tempering durations. Tempering reduced the kernel breaking strength and had significant effect on seed coat adhesion strength. Tempering the grain for 60 minutes at ambient ...

Effects of neck strength training on isometric neck strength in rugby union players.

Science.gov (United States)

Geary, Kevin; Green, Brian S; Delahunt, Eamonn

2014-11-01

To investigate the effectiveness of a neck strengthening program on the isometric neck strength profile of male rugby union players. Controlled laboratory study. Professional rugby union club. Fifteen professional and 10 semiprofessional rugby union players. The 15 professional players undertook a 5-week neck strengthening intervention, which was performed twice per week, whereas the 10 semiprofessional players acted as the control group. Isometric strength of the neck musculature was tested using a hand-held dynamometer, for flexion (F), extension (E), left-side flexion (LSF), and right-side flexion (RSF). Preintervention and postintervention evaluations were undertaken. No significant between-group differences in isometric neck strength were noted preintervention. A significant main effect for time was observed (P isometric neck strength in all planes after the 5-week intervention (F preintervention = 334.45 ± 39.31 N vs F postintervention 396.05 ± 75.55 N; E preintervention = 606.19 ± 97.34 vs E postintervention = 733.88 ± 127.16 N; LSF preintervention = 555.56 ± 88.34 N vs LSF postintervention = 657.14 ± 122.99 N; RSF preintervention = 570.00 ± 106.53 N vs RSF postintervention = 668.00 ± 142.18 N). No significant improvement in neck strength was observed for control group participants. The results of the present study indicate that a 5-week neck strengthening program improves isometric neck strength in rugby union players, which may have implications for injury prevention, screening, and rehabilitation. The strengthening program described in the present study may facilitate rehabilitation specialists in the development of neck injury prevention, screening, and rehabilitation protocols.

Effect of UV irradiation on the shear bond strength of titanium with segmented polyurethane through gamma-mercapto propyl trimethoxysilane.

Science.gov (United States)

Sakamoto, Harumi; Hirohashi, Yohei; Doi, Hisashi; Tsutsumi, Yusuke; Suzuki, Yoshiaki; Noda, Kazuhiko; Hanawa, Takao

2008-01-01

The objective of this study was to investigate the effect of UV irradiation on shear bond strength between a titanium (Ti) and a segmented polyurethane (SPU) composite through gamma-mercapto propyl trimethoxysilane (gamma-MPS). To this end, the shear bond strength of Ti/SPU interface of Ti-SPU composite under varying conditions of ultraviolet ray (UV) irradiation was evaluated by a shear bond test. The glass transition temperatures of SPU with and without UV irradiation were also determined using differential scanning calorimetry. It was found that the shear bond strength of Ti/SPU interface increased with UV irradiation. However, excessive UV irradiation decreased the shear bond strength of Ti/SPU interface. Glass transition temperature was found to increase during 40-60 seconds of UV irradiation. In terms of durability after immersion in water at 37 degrees C for 30 days, shear bond strength was found to improve with UV irradiation. In conclusion, UV irradiation to a Ti-SPU composite was clearly one of the means to improve the shear bond strength of Ti/SPU interface.

COLLISION STRENGTHS AND EFFECTIVE COLLISION STRENGTHS FOR TRANSITIONS WITHIN THE GROUND-STATE CONFIGURATION OF S III

Energy Technology Data Exchange (ETDEWEB)

Hudson, C. E.; Ramsbottom, C. A.; Scott, M. P., E-mail: c.hudson@qub.ac.uk, E-mail: c.ramsbottom@qub.ac.uk, E-mail: p.scott@qub.ac.uk [Department of Applied Maths and Theoretical Physics, The Queen' s University of Belfast, Belfast BT7 1NN (United Kingdom)

2012-05-01

We have carried out a 29-state R-matrix calculation in order to calculate collision strengths and effective collision strengths for the electron impact excitation of S III. The recently developed parallel RMATRX II suite of codes have been used, which perform the calculation in intermediate coupling. Collision strengths have been generated over an electron energy range of 0-12 Ryd, and effective collision strength data have been calculated from these at electron temperatures in the range 1000-100,000 K. Results are here presented for the fine-structure transitions between the ground-state configurations of 3s {sup 2}3p {sup 23} P{sub 0,1,2}, {sup 1}D{sub 2}, and {sup 1} S{sub 0}, and the values given resolve a discrepancy between two previous R-matrix calculations.

A Direct Test of the Differentiation Mechanism: REM, BCDMEM, and the Strength-Based Mirror Effect in Recognition Memory

Science.gov (United States)

Starns, Jeffrey J.; White, Corey N.; Ratcliff, Roger

2010-01-01

We explore competing explanations for the reduction in false alarm rate observed when studied items are strengthened. Some models, such as Retrieving Effectively from Memory (REM; Shiffrin & Steyvers, 1997), attribute the false alarm rate reduction to differentiation, a process in which strengthening memory traces at study directly reduces the…

Differential strengths of selection on S-RNases from Physalis and Solanum (Solanaceae

Directory of Open Access Journals (Sweden)

Kohn Joshua R

2011-08-01

Full Text Available Abstract Background The S-RNases of the Solanaceae are highly polymorphic self-incompatibility (S- alleles subject to strong balancing selection. Relatively recent diversification of S-alleles has occurred in the genus Physalis following a historical restriction of S-allele diversity. In contrast, the genus Solanum did not undergo a restriction of S-locus diversity and its S-alleles are generally much older. Because recovery from reduced S-locus diversity should involve increased selection, we employ a statistical framework to ask whether S-locus selection intensities are higher in Physalis than Solanum. Because different S-RNase lineages diversify in Physalis and Solanum, we also ask whether different sites are under selection in different lineages. Results Maximum-likelihood and Bayesian coalescent methods found higher intensities of selection and more sites under significant positive selection in the 48 Physalis S-RNase alleles than the 49 from Solanum. Highest posterior densities of dN/dS (ω estimates show that the strength of selection is greater for Physalis at 36 codons. A nested maximum likelihood method was more conservative, but still found 16 sites with greater selection in Physalis. Neither method found any codons under significantly greater selection in Solanum. A random effects likelihood method that examines data from both taxa jointly confirmed higher selection intensities in Physalis, but did not find different proportions of sites under selection in the two datasets. The greatest differences in strengths of selection were found in the most variable regions of the S-RNases, as expected if these regions encode self-recognition specificities. Clade-specific likelihood models indicated some codons were under greater selection in background Solanum lineages than in specific lineages of Physalis implying that selection on sites may differ among lineages. Conclusions Likelihood and Bayesian methods provide a statistical approach to

Effects of Strength vs. Ballistic-Power Training on Throwing Performance.

Science.gov (United States)

Zaras, Nikolaos; Spengos, Konstantinos; Methenitis, Spyridon; Papadopoulos, Constantinos; Karampatsos, Giorgos; Georgiadis, Giorgos; Stasinaki, Aggeliki; Manta, Panagiota; Terzis, Gerasimos

2013-01-01

The purpose of the present study was to investigate the effects of 6 weeks strength vs. ballistic-power (Power) training on shot put throwing performance in novice throwers. Seventeen novice male shot-put throwers were divided into Strength (N = 9) and Power (n = 8) groups. The following measurements were performed before and after the training period: shot put throws, jumping performance (CMJ), Wingate anaerobic performance, 1RM strength, ballistic throws and evaluation of architectural and morphological characteristics of vastus lateralis. Throwing performance increased significantly but similarly after Strength and Power training (7.0-13.5% vs. 6.0-11.5%, respectively). Muscular strength in leg press increased more after Strength than after Power training (43% vs. 21%, respectively), while Power training induced an 8.5% increase in CMJ performance and 9.0 - 25.8% in ballistic throws. Peak power during the Wingate test increased similarly after Strength and Power training. Muscle thickness increased only after Strength training (10%, p ballistic power training in novice throwers, but with dissimilar muscular adaptations. Key pointsBallistic-power training with 30% of 1RM is equally effective in increasing shot put performance as strength training, in novice throwers, during a short training cycle of six weeks.In novice shot putters with relatively low initial muscle strength/mass, short-term strength training might be more important since it can increase both muscle strength and shot put performance.The ballistic type of power training resulted in a significant increase of the mass of type IIx muscle fibres and no change in their proportion. Thus, this type of training might be used effectively during the last weeks before competition, when the strength training load is usually reduced, in order to increase muscle power and shot put performance in novice shot putters.

Energy dependence of the ratio of isovector effective interaction strengths |JστJτ| from 0° (p,n) cross sections

Science.gov (United States)

Taddeucci, T. N.; Rapaport, J.; Bainum, D. E.; Goodman, C. D.; Foster, C. C.; Gaarde, C.; Larsen, J.; Goulding, C. A.; Horen, D. J.; Masterson, T.; Sugarbaker, E.

1982-02-01

Information concerning the ratio of the isovector effective interaction strengths |JστJτ| may be obtained from the ratio of (p,n) Gamow-Teller and isobaric analog state 0° differential cross sections. We have examined 0° (p,n) data for the energy range 5-200 MeV and find that for energies larger than 50 MeV and for targets with A=7-42 the product of the interaction-strength and distortion-factor ratios |JστJτ|(NστNτ)12 appears to be mass independent and linear as a function of bombarding energy. NUCLEAR REACTIONS 7Li, 13, 14C, 26Mg, 37Cl, 41Ca(p,n), measured σ(θ=0°), GT, IAS transitions, Ep=60-200 MeV. Deduced energy dependence, interaction strength ratio |JστJτ|.

Effect of Ionic Strength on Settling of Activated Sludge

OpenAIRE

M Ahmadi Moghadam, M Soheili, MM Esfahani

2005-01-01

Structural properties of activated sludge flocs were found to be sensitive to small changes in ionic strength. This study investigates the effect of ionic strength on settling of activated sludge. Samples were taken from activated sludge process of Ghazvin Sasan soft drink wastewater treatment plant, then treated with different ionic strengths of KCl and CaCl2 solution, after that the turbidity of supernatant was measured. The results indicated that low ionic strength resulted in a steeper sl...

Bidirectional lipid droplet velocities are controlled by differential binding strengths of HCV core DII protein.

Directory of Open Access Journals (Sweden)

Rodney K Lyn

Full Text Available Host cell lipid droplets (LD are essential in the hepatitis C virus (HCV life cycle and are targeted by the viral capsid core protein. Core-coated LDs accumulate in the perinuclear region and facilitate viral particle assembly, but it is unclear how mobility of these LDs is directed by core. Herein we used two-photon fluorescence, differential interference contrast imaging, and coherent anti-Stokes Raman scattering microscopies, to reveal novel core-mediated changes to LD dynamics. Expression of core protein's lipid binding domain II (DII-core induced slower LD speeds, but did not affect directionality of movement on microtubules. Modulating the LD binding strength of DII-core further impacted LD mobility, revealing the temporal effects of LD-bound DII-core. These results for DII-core coated LDs support a model for core-mediated LD localization that involves core slowing down the rate of movement of LDs until localization at the perinuclear region is accomplished where LD movement ceases. The guided localization of LDs by HCV core protein not only is essential to the viral life cycle but also poses an interesting target for the development of antiviral strategies against HCV.

Effect of 8 weeks of free-weight and machine-based strength training on strength and power performance

OpenAIRE

Wirth Klaus; Keiner Michael; Hartmann Hagen; Sander Andre; Mickel Christoph

2016-01-01

Abstract The aim of this study was to evaluate the effectiveness of free-weight and machine-based exercises to increase different strength and speed-strength variables. One hundred twenty male participants (age: 23.8 ? 2.5 years; body height: 181.0 ? 6.8 cm; body mass: 80.2 ? 8.9 kg) joined the study. The 2 experimental groups completed an 8 week periodized strength training program that included 2 training sessions per week. The exercises that were used in the strength training programs were...

Differential effects of strength training and testosterone treatment on soluble CD36 in aging men

DEFF Research Database (Denmark)

Glintborg, Dorte; Christensen, Louise L; Kvorning, Thue

2015-01-01

PURPOSE: We measured soluble CD36 (sCD36) and body composition to determine the effects of testosterone treatment (TT) and/or strength training (ST) on cardiovascular risk in men with low normal testosterone levels. METHODS: Double-blinded, placebo-controlled study in 54 men aged 60-78 years...... with bioavailable testosterone 94 cm randomized to TT (gel, 50-100 mg/day, n = 20), placebo (n = 18) or ST (n = 16) for 6 months. Moreover, the ST group was randomized to TT (ST + TT, n = 7) or placebo (ST + placebo, n = 9) after 3 months. OUTCOMES: sCD36, total and regional fat mass were....... units] vs. TT and vs. placebo (p testosterone and lean body mass. Fat mass measures significantly improved during ST + placebo, ST + TT, and TT vs. placebo. During ST + placebo, delta sCD36 was associated with delta total fat mass (r = 0.81) and delta...

Strengths in older adults: differential effect of savoring, gratitude and optimism on well-being.

Science.gov (United States)

Salces-Cubero, Isabel María; Ramírez-Fernández, Encarnación; Ortega-Martínez, Ana Raquel

2018-05-21

Objetive: The present study aimed to compare the efficacy of three separate strengths training-based interventions - Gratitude, Savoring, and Optimism - in older adults. The sample comprised 124 older adults, namely, 74 women and 50 men, non-institutionalized individuals who regularly attend day centers in the provinces of Jaén and Córdoba, southern Spain. Their ages ranged between 60 and 89 years. The measures used were Anxiety, Depression, Life Satisfaction, Positive and Negative Affect, Subjective Happiness, and Resilience. Training in Gratitude and Savoring increased scores in Life Satisfaction, Positive Affect, Subjective Happiness and Resilience, and reduced Negative Affect, whereas training in Optimism failed to produce a significant change in these variables. The Savoring and Optimism interventions decreased scores in Depression but, contrary to hypothesis, this was not the case for Gratitude. These results represent an important step in understanding what type of strengths work best when it comes to enhancing well-being in older adults and consequently helping them tackle the challenges of everyday life and recover as quickly as possible from the adverse situations and events that may arise.

Size Effects on the Strength of Metals

DEFF Research Database (Denmark)

Huang, Xiaoxu

2014-01-01

The grain size effect and the specimen size effect on the strength of metals are briefly reviewed with respect to their history and current status of research. It is revealed that the fundamental strengthening mechanisms responsible for these two types of size effect are to increase the resistanc...

Modeling Differentiation of Cognitive Abilities within the Higher-Order Factor Model Using Moderated Factor Analysis

Science.gov (United States)

Molenaar, Dylan; Dolan, Conor V.; Wicherts, Jelte M.; van der Maas, Han L. J.

2010-01-01

The general differentiation hypothesis states that the strength of the correlations among a set of IQ subtests varies with a given variable. Instances of the general differentiation hypothesis that have been considered in the literature include age and ability differentiation. Traditionally, the differentiation effect is attributed to the varying…

Differential Effects of Heavy Versus Moderate Loads on Measures of Strength and Hypertrophy in Resistance-Trained Men.

Science.gov (United States)

Schoenfeld, Brad J; Contreras, Bret; Vigotsky, Andrew D; Peterson, Mark

2016-12-01

The purpose of the present study was to evaluate muscular adaptations between heavy- and moderate-load resistance training (RT) with all other variables controlled between conditions. Nineteen resistance-trained men were randomly assigned to either a strength-type RT routine (HEAVY) that trained in a loading range of 2-4 repetitions per set (n = 10) or a hypertrophy-type RT routine (MODERATE) that trained in a loading range of 8-12 repetitions per set (n = 9). Training was carried out 3 days a week for 8 weeks. Both groups performed 3 sets of 7 exercises for the major muscle groups of the upper and lower body. Subjects were tested pre- and post-study for: 1 repetition maximum (RM) strength in the bench press and squat, upper body muscle endurance, and muscle thickness of the elbow flexors, elbow extensors, and lateral thigh. Results showed statistically greater increases in 1RM squat strength favoring HEAVY compared to MODERATE. Alternatively, statistically greater increases in lateral thigh muscle thickness were noted for MODERATE versus HEAVY. These findings indicate that heavy load training is superior for maximal strength goals while moderate load training is more suited to hypertrophy-related goals when an equal number of sets are performed between conditions.

Differential Effects of Heavy Versus Moderate Loads on Measures of Strength and Hypertrophy in Resistance-Trained Men

Directory of Open Access Journals (Sweden)

Brad J. Schoenfeld, Bret Contreras, Andrew D. Vigotsky, Mark Peterson

2016-12-01

Full Text Available The purpose of the present study was to evaluate muscular adaptations between heavy- and moderate-load resistance training (RT with all other variables controlled between conditions. Nineteen resistance-trained men were randomly assigned to either a strength-type RT routine (HEAVY that trained in a loading range of 2-4 repetitions per set (n = 10 or a hypertrophy-type RT routine (MODERATE that trained in a loading range of 8-12 repetitions per set (n = 9. Training was carried out 3 days a week for 8 weeks. Both groups performed 3 sets of 7 exercises for the major muscle groups of the upper and lower body. Subjects were tested pre- and post-study for: 1 repetition maximum (RM strength in the bench press and squat, upper body muscle endurance, and muscle thickness of the elbow flexors, elbow extensors, and lateral thigh. Results showed statistically greater increases in 1RM squat strength favoring HEAVY compared to MODERATE. Alternatively, statistically greater increases in lateral thigh muscle thickness were noted for MODERATE versus HEAVY. These findings indicate that heavy load training is superior for maximal strength goals while moderate load training is more suited to hypertrophy-related goals when an equal number of sets are performed between conditions.

Situational Strength Cues from Social Sources at Work: Relative Importance and Mediated Effects.

Science.gov (United States)

Alaybek, Balca; Dalal, Reeshad S; Sheng, Zitong; Morris, Alexander G; Tomassetti, Alan J; Holland, Samantha J

2017-01-01

Situational strength is considered one of the most important situational forces at work because it can attenuate the personality-performance relationship. Although organizational scholars have studied the consequences of situational strength, they have paid little attention to its antecedents. To address this gap, the current study focused on situational strength cues from different social sources as antecedents of overall situational strength at work. Specifically, we examined how employees combine situational strength cues emanating from three social sources (i.e., coworkers, the immediate supervisor, and top management). Based on field theory, we hypothesized that the effect of situational strength from coworkers and immediate supervisors (i.e., proximal sources of situational strength) on employees' perceptions of overall situational strength on the job would be greater than the effect of situational strength from the top management (i.e., the distal source of situational strength). We also hypothesized that the effect of situational strength from the distal source would be mediated by the effects of situational strength from the proximal sources. Data from 363 full-time employees were collected at two time points with a cross-lagged panel design. The former hypothesis was supported for one of the two situational strength facets studied. The latter hypothesis was fully supported.

Situational Strength Cues from Social Sources at Work: Relative Importance and Mediated Effects

Directory of Open Access Journals (Sweden)

Balca Alaybek

2017-09-01

Full Text Available Situational strength is considered one of the most important situational forces at work because it can attenuate the personality–performance relationship. Although organizational scholars have studied the consequences of situational strength, they have paid little attention to its antecedents. To address this gap, the current study focused on situational strength cues from different social sources as antecedents of overall situational strength at work. Specifically, we examined how employees combine situational strength cues emanating from three social sources (i.e., coworkers, the immediate supervisor, and top management. Based on field theory, we hypothesized that the effect of situational strength from coworkers and immediate supervisors (i.e., proximal sources of situational strength on employees' perceptions of overall situational strength on the job would be greater than the effect of situational strength from the top management (i.e., the distal source of situational strength. We also hypothesized that the effect of situational strength from the distal source would be mediated by the effects of situational strength from the proximal sources. Data from 363 full-time employees were collected at two time points with a cross-lagged panel design. The former hypothesis was supported for one of the two situational strength facets studied. The latter hypothesis was fully supported.

Effects of etching time on enamel bond strengths.

Science.gov (United States)

Triolo, P T; Swift, E J; Mudgil, A; Levine, A

1993-12-01

This study evaluated the effects of etching time on bond strengths of composite to enamel. Proximal surfaces of extracted molars were etched with either a conventional etchant (35% phosphoric acid) or one of two dentin/enamel conditioners, 10% maleic acid (Scotchbond Multi-Purpose Etchant), or a solution of oxalic acid, aluminum nitrate, and glycine (Gluma 1 & 2 Conditioner). Each agent was applied for 15, 30, or 60 seconds. Specimens etched with 35% phosphoric acid had the highest mean bond strengths at each etching time. At the manufacturer's recommended application times, the other two agents gave significantly lower shear bond strengths than phosphoric acid.

Effect of microstructure on the high temperature strength of nitride

Indian Academy of Sciences (India)

Effect of microstructure on the high temperature strength of nitride bonded silicon carbide composite. J Rakshit P K Das. Composites Volume ... The effect of these parameters on room temperature and high temperature strength of the composite up to 1300°C in ambient condition were studied. The high temperature flexural ...

Multistep triaxial strength tests: investigating strength parameters and pore pressure effects on Opalinus Clay

International Nuclear Information System (INIS)

Graesle, W.

2010-01-01

Document available in extended abstract form only. The impact of natural variability between rock samples from a single formation is a common problem for the characterisation of THM properties of rocks. Data variation arising from heterogeneity between samples often obscures details of material behaviour. Besides efforts to reduce this statistical noise by careful selection of samples, there are essentially two approaches to overcome this problem: - To generate very large data sets for better statistics. - To avoid the impact of natural variability by yielding an extensive data set from a single sample. The multistep strength test follows the latter approach to characterise the mechanical behaviour of Opalinus Clay from Mont Terri and the possible impact of pore pressure effects. The concept of the multistep strength test comprises three test sections, each focused on the investigation of one mechanical characteristic of Opalinus Clay. Any section is composed of a series of strain controlled load cycles at various levels of confining pressure. 1) The linear elastic limit, i.e. the onset of nonlinearity in the stress-strain-relationship σ dev (ε 1 ) during strain-controlled triaxial loading, is determined in section 1. It defines a lower limit for the onset of damage. Avoiding sample damage is essential during this test section to ensure that all measurements reflect the behaviour of undisturbed material. Therefore, a rather strict and well detectable criterion for the onset of nonlinearity is required to enable a timely termination of any load phase. 2) Section 2 is focused on shear strength. Any load cycle is stopped as soon as peak stress is detected. As progressive damage of the sample is unavoidable during this process, it must be expected that only very few measured peak stresses approximately represent properties of the undamaged material. 3) Test section 3 is a conventional test of residual strength. Tests are carried out on cylindrical samples (100 mm

Effects of strength training, detraining and retraining in muscle strength, hypertrophy and functional tasks in older female adults.

Science.gov (United States)

Correa, Cleiton S; Cunha, Giovani; Marques, Nise; Oliveira-Reischak, Ãlvaro; Pinto, Ronei

2016-07-01

Previous studies presented different results regarding the maintenance time of muscular adaptations after strength training and the ability to resume the gains on muscular performance after resumption of the training programme. This study aimed to verify the effect of strength training on knee extensors and elbow flexor muscle strength, rectus femoris muscle volume and functional performance in older female adults after 12 weeks of strength training, 1 year of detraining and followed by 12 weeks of retraining. Twelve sedentary older women performed 12 weeks of strength training, 1 year of detraining and 12 weeks of retraining. The strength training was performed twice a week, and the assessment was made four times: at the baseline, after the strength training, after the detraining and after the retraining. The knee extensor and elbow flexor strength, rectus femoris muscle volume and functional task were assessed. Strength of knee extensor and elbow flexor muscles, rectus femoris muscle volume and 30-s sit-to-stand increased from baseline to post-training (respectively, 40%, 70%, 38% and 46%), decreased after detraining (respectively, -36%, -64%, -35% and -43%) and increased again these parameters after retraining (35%, 68%, 36% and 42%). Strength training induces gains on strength and hypertrophy, also increased the performance on functional tasks after the strength training. The stoppage of the strength caused strength loss and reduction of functional performance. The resumption of the strength training promoted the same gains of muscular performance in older female adults. © 2015 Scandinavian Society of Clinical Physiology and Nuclear Medicine. Published by John Wiley & Sons Ltd.

Effectiveness of Traditional Strength vs. Power Training on Muscle Strength, Power and Speed with Youth: A Systematic Review and Meta-Analysis

Science.gov (United States)

Behm, David G.; Young, James D.; Whitten, Joseph H. D.; Reid, Jonathan C.; Quigley, Patrick J.; Low, Jonathan; Li, Yimeng; Lima, Camila D.; Hodgson, Daniel D.; Chaouachi, Anis; Prieske, Olaf; Granacher, Urs

2017-01-01

Numerous national associations and multiple reviews have documented the safety and efficacy of strength training for children and adolescents. The literature highlights the significant training-induced increases in strength associated with youth strength training. However, the effectiveness of youth strength training programs to improve power measures is not as clear. This discrepancy may be related to training and testing specificity. Most prior youth strength training programs emphasized lower intensity resistance with relatively slow movements. Since power activities typically involve higher intensity, explosive-like contractions with higher angular velocities (e.g., plyometrics), there is a conflict between the training medium and testing measures. This meta-analysis compared strength (e.g., training with resistance or body mass) and power training programs (e.g., plyometric training) on proxies of muscle strength, power, and speed. A systematic literature search using a Boolean Search Strategy was conducted in the electronic databases PubMed, SPORT Discus, Web of Science, and Google Scholar and revealed 652 hits. After perusal of title, abstract, and full text, 107 studies were eligible for inclusion in this systematic review and meta-analysis. The meta-analysis showed small to moderate magnitude changes for training specificity with jump measures. In other words, power training was more effective than strength training for improving youth jump height. For sprint measures, strength training was more effective than power training with youth. Furthermore, strength training exhibited consistently large magnitude changes to lower body strength measures, which contrasted with the generally trivial, small and moderate magnitude training improvements of power training upon lower body strength, sprint and jump measures, respectively. Maturity related inadequacies in eccentric strength and balance might influence the lack of training specificity with the unilateral

Effectiveness of Traditional Strength vs. Power Training on Muscle Strength, Power and Speed with Youth: A Systematic Review and Meta-Analysis

Directory of Open Access Journals (Sweden)

David G. Behm

2017-06-01

Full Text Available Numerous national associations and multiple reviews have documented the safety and efficacy of strength training for children and adolescents. The literature highlights the significant training-induced increases in strength associated with youth strength training. However, the effectiveness of youth strength training programs to improve power measures is not as clear. This discrepancy may be related to training and testing specificity. Most prior youth strength training programs emphasized lower intensity resistance with relatively slow movements. Since power activities typically involve higher intensity, explosive-like contractions with higher angular velocities (e.g., plyometrics, there is a conflict between the training medium and testing measures. This meta-analysis compared strength (e.g., training with resistance or body mass and power training programs (e.g., plyometric training on proxies of muscle strength, power, and speed. A systematic literature search using a Boolean Search Strategy was conducted in the electronic databases PubMed, SPORT Discus, Web of Science, and Google Scholar and revealed 652 hits. After perusal of title, abstract, and full text, 107 studies were eligible for inclusion in this systematic review and meta-analysis. The meta-analysis showed small to moderate magnitude changes for training specificity with jump measures. In other words, power training was more effective than strength training for improving youth jump height. For sprint measures, strength training was more effective than power training with youth. Furthermore, strength training exhibited consistently large magnitude changes to lower body strength measures, which contrasted with the generally trivial, small and moderate magnitude training improvements of power training upon lower body strength, sprint and jump measures, respectively. Maturity related inadequacies in eccentric strength and balance might influence the lack of training specificity with

Analytical evaluation of the environment effect on creep rupture strength

International Nuclear Information System (INIS)

Tamura, Manabu; Ogawa, Yutaka; Kurata, Yuji; Kondo, Tatsuo

1982-04-01

An analytical approach was made in evaluating semi-quantitatively the effect of environment on rupture strength of materials. In the analysis the zone formed in the material by reaction with the environment was assumed to bear the applied load as one of the strength members. In calculations a law of mixtures of creep strength and the linear damage rule were applied. In the modeling of the load bearing by the composite structure of the environment-affected and intact zones, both parallel and series models were considered to formulate the equations. The equation for the parallel-loaded model was properly adopted in explaining semi-quantitatively the case of Incoloy alloy 800 crept in air, which was strengthened with the layer formed by nitrization. The equation for the serially loaded model was more successfully adopted to the evaluation of the rupture strength of dissimilar weld joints. The latter was also considered to be potentially adoptable to the problems of the effect of specimen size and shape on rupture strength, which had been often taken into account in evaluating the environment effect. For application of the developed method, examination was made to the possible decrease in rupture strength of Hastelloy alloy XR in long term tests by the formation of Cr depleted zone due to oxidation in HTGR impure helium, and the results were compared with the values obtained by experiments. (author)

Computer-aided model analysis for ionic strength-dependent effective charge of protein in ion-exchange chromatography

DEFF Research Database (Denmark)

Lim, Young-il; Jørgensen, Sten Bay; Kim, In-Ho

2005-01-01

differential algebraic equation (PDAE) system, a fast and accurate numerical method (i.e., conservation element/solution element (CE/SE) method), is proposed. Sensitivity and elasticity of the model parameters (e.g., steric/shape factors, adsorption heat coefficient, effective protein charge, equilibrium...... constant, mass transfer coefficient, axial dispersion coefficient and bed voidage) are analyzed for a BSA-salt system in a low protein concentration range. Within a low concentration range of bovine serum albumin (BSA) where linear adsorption isotherms are shown, the adsorption heat coefficient, shape...... salt concentrations, it is proposed that the effective protein charge could depend upon the salt concentration (or ionic strength). The reason for this dependence may be a steric hindrance of protein binding sites combined with a salt shielding effect neutralizing the surface charges of the protein. (c...

Effective longitudinal strength of high temperature metal-matrix composites

International Nuclear Information System (INIS)

Craddock, J.N.; Savvides, I.

1991-01-01

Several models for predicting the longitudinal strength of fiber composites are presented, ranging from a simple netting analysis to a model incorporating curvilinear strain hardening for all the components. Results from these models are presented for tungsten fiber reinforced superalloys, FeCrAlY and MARM200. It is shown that a simple elastic limit micromechanical model does not always adequately describe the useful strength of the composites. The methods proposed here are shown to be more appropriate for predicting the effective composite strength. 2 refs

Examining Differential Resilience Mechanisms by Comparing 'Tipping Points' of the Effects of Neighborhood Conditions on Anxiety by Race/Ethnicity.

Science.gov (United States)

Coman, Emil Nicolae; Wu, Helen Zhao

2018-02-20

Exposure to adverse environmental and social conditions affects physical and mental health through complex mechanisms. Different racial/ethnic (R/E) groups may be more or less vulnerable to the same conditions, and the resilience mechanisms that can protect them likely operate differently in each population. We investigate how adverse neighborhood conditions (neighborhood disorder, NDis) differentially impact mental health (anxiety, Anx) in a sample of white and Black (African American) young women from Southeast Texas, USA. We illustrate a simple yet underutilized segmented regression model where linearity is relaxed to allow for a shift in the strength of the effect with the levels of the predictor. We compare how these effects change within R/E groups with the level of the predictor, but also how the "tipping points," where the effects change in strength, may differ by R/E. We find with classic linear regression that neighborhood disorder adversely affects Black women's anxiety, while in white women the effect seems negligible. Segmented regressions show that the Ndis → Anx effects in both groups of women appear to shift at similar levels, about one-fifth of a standard deviation below the mean of NDis, but the effect for Black women appears to start out as negative, then shifts in sign, i.e., to increase anxiety, while for white women, the opposite pattern emerges. Our findings can aid in devising better strategies for reducing health disparities that take into account different coping or resilience mechanisms operating differentially at distinct levels of adversity. We recommend that researchers investigate when adversity becomes exceedingly harmful and whether this happens differentially in distinct populations, so that intervention policies can be planned to reverse conditions that are more amenable to change, in effect pushing back the overall social risk factors below such tipping points.

The List-Strength Effect in Recall: Relative-Strength Competition and Retrieval Inhibition May both Contribute to Forgetting

Science.gov (United States)

Verde, Michael F.

2009-01-01

According to the principle of relative-strength competition, stronger items in memory block the retrieval of weaker items. This principle, integral to many theories of forgetting over the years, derives much of its support from the list-strength effect (LSE), in which strengthening some items in a study list makes it more difficult to recall other…

Effects of strength training on blood lipoprotein concentrations in postmenopausal women

Directory of Open Access Journals (Sweden)

Cleiton Silva Correa

2014-12-01

Full Text Available Strength training is often identified as a contributing factor in prevention of diseases and as a non-pharmacological treatment for metabolic disorders and for control of body mass. Its protective effects and utility for management of disease are amplified in people at risk of diabetes mellitus and dyslipidemias, and cardiovascular diseases (CVD. Recently the benefits of strength training have been used to reduce the risk of these diseases emerging in postmenopausal women, who are at greater risk of CVD than men of the same age. Notwithstanding, little is known about the effects of strength training on metabolism of blood lipoproteins. The objective of this review was to compare the results of articles that have investigated the effects on lipoprotein concentrations of strength training in postmenopausal women. Current articles dealing with the subject, with publication dates from 1979 to 2012 and large numbers of citations by well-known researchers were identified on the Pubmed, Scopus and EBSCO databases. It was concluded that strength training possibly has an action that affects lipoprotein metabolism and concentrations in postmenopausal women.

Effect of silver nano particles on flexural strength of acrylic resins.

Science.gov (United States)

Sodagar, Ahmad; Kassaee, Mohammad Zaman; Akhavan, Azam; Javadi, Negar; Arab, Sepideh; Kharazifard, Mohammad Javad

2012-04-01

Poly(methyl methacrylate), PMMA, is widely used for fabrication of removable orthodontic appliances. Silver nano particles (AgNps) have been added to PMMA because of their antimicrobial properties. The aim of this study is to investigate the effect of AgNps on the flexural strength of PMMA. Acrylic liquid containing 0.05% and 0.2% AgNps was prepared for two kinds of acrylic resins: Rapid Repair &Selecta Plus. Two groups without AgNps were used as control groups. For each one, flexural strength was investigated via Three Point Bending method for the 15 acrylic blocks. Two-way ANOVA, one way ANOVA and Tukey tests were used for statistical analysis. Rapid Repair without AgNps showed the highest flexural strength. Addition of 0.05% AgNps to Rapid Repair, significantly decreased its flexural strength while, continuing the addition up to 0.2% increased it nearly up to its primary level. In contrast, addition of AgNps to Selecta Plus increased its flexural strength but addition of 0.05% nano particles was more effective than 0.2%. The effect of AgNps on flexural strength of PMMA depends on several factors including the type of acrylics and the concentrations of nano particles. Copyright © 2011 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

Fish-oil supplementation enhances the effects of strength training in elderly women.

Science.gov (United States)

Rodacki, Cintia L N; Rodacki, André L F; Pereira, Gleber; Naliwaiko, Katya; Coelho, Isabela; Pequito, Daniele; Fernandes, Luiz Cléudio

2012-02-01

Muscle force and functional capacity generally decrease with aging in the older population, although this effect can be reversed, attenuated, or both through strength training. Fish oil (FO), which is rich in n-3 (omega-3) PUFAs, has been shown to play a role in the plasma membrane and cell function of muscles, which may enhance the benefits of training. The effect of strength training and FO supplementation on the neuromuscular system of the elderly has not been investigated. The objective was to investigate the chronic effect of FO supplementation and strength training on the neuromuscular system (muscle strength and functional capacity) of older women. Forty-five women (aged 64 ± 1.4 y) were randomly assigned to 3 groups. One group performed strength training only (ST group) for 90 d, whereas the others performed the same strength-training program and received FO supplementation (2 g/d) for 90 d (ST90 group) or for 150 d (ST150 group; supplemented 60 d before training). Muscle strength and functional capacity were assessed before and after the training period. No differences in the pretraining period were found between groups for any of the variables. The peak torque and rate of torque development for all muscles (knee flexor and extensor, plantar and dorsiflexor) increased from pre- to posttraining in all groups. However, the effect was greater in the ST90 and ST150 groups than in the ST group. The activation level and electromechanical delay of the muscles changed from pre- to posttraining only for the ST90 and ST150 groups. Chair-rising performance in the FO groups was higher than in the ST group. Strength training increased muscle strength in elderly women. The inclusion of FO supplementation caused greater improvements in muscle strength and functional capacity.

Simultaneous estimation of strength and position of a heat source in a participating medium using DE algorithm

International Nuclear Information System (INIS)

Parwani, Ajit K.; Talukdar, Prabal; Subbarao, P.M.V.

2013-01-01

An inverse heat transfer problem is discussed to estimate simultaneously the unknown position and timewise varying strength of a heat source by utilizing differential evolution approach. A two dimensional enclosure with isothermal and black boundaries containing non-scattering, absorbing and emitting gray medium is considered. Both radiation and conduction heat transfer are included. No prior information is used for the functional form of timewise varying strength of heat source. The finite volume method is used to solve the radiative transfer equation and the energy equation. In this work, instead of measured data, some temperature data required in the solution of the inverse problem are taken from the solution of the direct problem. The effect of measurement errors on the accuracy of estimation is examined by introducing errors in the temperature data of the direct problem. The prediction of source strength and its position by the differential evolution (DE) algorithm is found to be quite reasonable. -- Highlights: •Simultaneous estimation of strength and position of a heat source. •A conducting and radiatively participating medium is considered. •Implementation of differential evolution algorithm for such kind of problems. •Profiles with discontinuities can be estimated accurately. •No limitation in the determination of source strength at the final time

New true-triaxial rock strength criteria considering intrinsic material characteristics

Science.gov (United States)

Zhang, Qiang; Li, Cheng; Quan, Xiaowei; Wang, Yanning; Yu, Liyuan; Jiang, Binsong

2018-02-01

A reasonable strength criterion should reflect the hydrostatic pressure effect, minimum principal stress effect, and intermediate principal stress effect. The former two effects can be described by the meridian curves, and the last one mainly depends on the Lode angle dependence function. Among three conventional strength criteria, i.e. Mohr-Coulomb (MC), Hoek-Brown (HB), and Exponent (EP) criteria, the difference between generalized compression and extension strength of EP criterion experience a firstly increase then decrease process, and tends to be zero when hydrostatic pressure is big enough. This is in accordance with intrinsic rock strength characterization. Moreover, the critical hydrostatic pressure I_c corresponding to the maximum difference of between generalized compression and extension strength can be easily adjusted by minimum principal stress influence parameter K. So, the exponent function is a more reasonable meridian curves, which well reflects the hydrostatic pressure effect and is employed to describe the generalized compression and extension strength. Meanwhile, three Lode angle dependence functions of L_{{MN}}, L_{{WW}}, and L_{{YMH}}, which unconditionally satisfy the convexity and differential requirements, are employed to represent the intermediate principal stress effect. Realizing the actual strength surface should be located between the generalized compression and extension surface, new true-triaxial criteria are proposed by combining the two states of EP criterion by Lode angle dependence function with a same lode angle. The proposed new true-triaxial criteria have the same strength parameters as EP criterion. Finally, 14 groups of triaxial test data are employed to validate the proposed criteria. The results show that the three new true-triaxial exponent criteria, especially the Exponent Willam-Warnke criterion (EPWW) criterion, give much lower misfits, which illustrates that the EP criterion and L_{{WW}} have more reasonable meridian

Simulated weightlessness and synbiotic diet effects on rat bone mechanical strength

Science.gov (United States)

Sarper, Hüseyin; Blanton, Cynthia; DePalma, Jude; Melnykov, Igor V.; Gabaldón, Annette M.

2014-10-01

This paper reports results on exposure to simulated weightlessness that leads to a rapid decrease in bone mineral density known as spaceflight osteopenia by evaluating the effectiveness of dietary supplementation with synbiotics to counteract the effects of skeletal unloading. Forty adult male rats were studied under four different conditions in a 2 × 2 factorial design with main effects of diet (synbiotic and control) and weight condition (unloaded and control). Hindlimb unloading was performed at all times for 14 days followed by 14 days of recovery (reambulation). The synbiotic diet contained probiotic strains Lactobacillus acidophilus and Lactococcus lactis lactis and prebiotic fructooligosaccharide. This paper also reports on the development of a desktop three-point bending device to measure the mechanical strength of bones from rats subjected to simulated weightlessness. The importance of quantifying bone resistance to breakage is critical when examining the effectiveness of interventions against osteopenia resulting from skeletal unloading, such as astronauts experience, disuse or disease. Mechanical strength indices provide information beyond measures of bone density and microarchitecture that enhance the overall assessment of a treatment's potency. In this study we used a newly constructed three-point bending device to measure the mechanical strength of femur and tibia bones from hindlimb-unloaded rats fed an experimental synbiotic diet enriched with probiotics and fermentable fiber. Two calculated outputs for each sample were Young's modulus of elasticity and fracture stress. Bone major elements (calcium, magnesium, and phosphorous) were quantified using ICP-MS analysis. Hindlimb unloading was associated with a significant loss of strength in the femur, and with significant reductions in major bone elements. The synbiotic diet did not protect against these unloading effects. Tibia strength and major elements were not reduced by hindlimb unloading, as was

Global model for the lithospheric strength and effective elastic thickness

OpenAIRE

Magdala Tesauro; Mikhail Kaban; S. A. P. L. Cloetingh

2013-01-01

Global distribution of the strength and effective elastic thickness (Te) of the lithosphere are estimated using physical parameters from recent crustal and lithospheric models. For the Te estimation we apply a new approach, which provides a possibility to take into account variations of Young modulus (E) within the lithosphere. In view of the large uncertainties affecting strength estimates, we evaluate global strength and Te distributions for possible end-member ‘hard’ (HRM) and a ‘soft’ (SR...

Examining Differential Resilience Mechanisms by Comparing ‘Tipping Points’ of the Effects of Neighborhood Conditions on Anxiety by Race/Ethnicity

Directory of Open Access Journals (Sweden)

Emil Nicolae Coman

2018-02-01

Full Text Available Exposure to adverse environmental and social conditions affects physical and mental health through complex mechanisms. Different racial/ethnic (R/E groups may be more or less vulnerable to the same conditions, and the resilience mechanisms that can protect them likely operate differently in each population. We investigate how adverse neighborhood conditions (neighborhood disorder, NDis differentially impact mental health (anxiety, Anx in a sample of white and Black (African American young women from Southeast Texas, USA. We illustrate a simple yet underutilized segmented regression model where linearity is relaxed to allow for a shift in the strength of the effect with the levels of the predictor. We compare how these effects change within R/E groups with the level of the predictor, but also how the “tipping points,” where the effects change in strength, may differ by R/E. We find with classic linear regression that neighborhood disorder adversely affects Black women’s anxiety, while in white women the effect seems negligible. Segmented regressions show that the Ndis → Anx effects in both groups of women appear to shift at similar levels, about one-fifth of a standard deviation below the mean of NDis, but the effect for Black women appears to start out as negative, then shifts in sign, i.e., to increase anxiety, while for white women, the opposite pattern emerges. Our findings can aid in devising better strategies for reducing health disparities that take into account different coping or resilience mechanisms operating differentially at distinct levels of adversity. We recommend that researchers investigate when adversity becomes exceedingly harmful and whether this happens differentially in distinct populations, so that intervention policies can be planned to reverse conditions that are more amenable to change, in effect pushing back the overall social risk factors below such tipping points.

Effects of small defects and nonmetallic inclusions on the fatigue strength of metals

International Nuclear Information System (INIS)

Murakami, Y.

1991-01-01

The equation for predicting the effects of artificial small defects on the fatigue strength of metals is introduced, and it is applied to the quantitative evaluation of the effects of nonmetallic inclusions on the fatigue strength of high-strength steels. The importance of the concept that nonmetallic inclusions are virtually equivalent to defects, from the viewpoint of fatigue strength and, more practically, are equivalent to small cracks is emphasized. It is shown that nonmetallic inclusions cause relatively low-fatigue strength and large scatter of the fatigue strength of steels with high static strength or high hardness. The statistics of extreme values is used to estimate the expected maximum size of nonmetallic inclusions contained in a definite number of specimens. The lower limit of scatter in the fatigue strength of a high-strength steel is obtained by using the prediction equation for small defects together with the expected maximum size of nonmetallic inclusions

EFFECTS OF STRENGTH VS. BALLISTIC-POWER TRAINING ON THROWING PERFORMANCE

Directory of Open Access Journals (Sweden)

Nikolaos Zaras

2013-03-01

Full Text Available The purpose of the present study was to investigate the effects of 6 weeks strength vs. ballistic-power (Power training on shot put throwing performance in novice throwers. Seventeen novice male shot-put throwers were divided into Strength (N = 9 and Power (n = 8 groups. The following measurements were performed before and after the training period: shot put throws, jumping performance (CMJ, Wingate anaerobic performance, 1RM strength, ballistic throws and evaluation of architectural and morphological characteristics of vastus lateralis. Throwing performance increased significantly but similarly after Strength and Power training (7.0-13.5% vs. 6.0-11.5%, respectively. Muscular strength in leg press increased more after Strength than after Power training (43% vs. 21%, respectively, while Power training induced an 8.5% increase in CMJ performance and 9.0 - 25.8% in ballistic throws. Peak power during the Wingate test increased similarly after Strength and Power training. Muscle thickness increased only after Strength training (10%, p < 0.05. Muscle fibre Cross Sectional Area (fCSA increased in all fibre types after Strength training by 19-26% (p < 0.05, while only type IIx fibres hypertrophied significantly after Power training. Type IIx fibres (% decreased after Strength but not after Power training. These results suggest that shot put throwing performance can be increased similarly after six weeks of either strength or ballistic power training in novice throwers, but with dissimilar muscular adaptations

Effect of fluoride mouthwash on tensile strength of stainless steel orthodontic archwires

Science.gov (United States)

Fatimah, D. I.; Anggani, H. S.; Ismah, N.

2017-08-01

Patients with orthodontic treatment are commonly recommended to use a fluoride mouthwash for maintaining their oral hygiene and preventing dental caries. However, fluoride may affect the characteristics of stainless steel orthodontic archwires used during treatment. The effect of fluoride mouthwash on the tensile strength of stainless steel orthodontic archwires is still unknown. The purpose of this study is to know the effect of fluoride mouthwash on the tensile strength of stainless steel orthodontic archwires. Examine the tensile strength of 0.016 inch stainless steel orthodontic archwires after immersion in 0.05%, 100 ml fluoride mouthwash for 30, 60, and 90 min. There is no statistically significant difference in the tensile strength of stainless steel orthodontic archwires after immersed in fluoride mouthwash. The p-values on immersion fluoride mouthwash for 30, 60, and 90 min consecutively are 0.790; 0.742; and 0.085 (p > 0.05). The use of fluoride mouthwash did not have an effect on the tensile strength of stainless Steel orthodontic archwires.

Effect of strength training on muscle function in elderly hospitalized patients

DEFF Research Database (Denmark)

Suetta, C; Magnusson, S P; Beyer, N

2007-01-01

Immobilization due to hospitalization and major surgery leads to an increased risk of morbidity, disability and a decline in muscle function especially in frail elderly individuals. In fact, many elderly patients fail to regain their level of function and self-care before admission to hospital....... Given that reduced lower limb muscle strength and loss of skeletal muscle mass (i.e. sarcopenia) have been associated with functional impairments and disability with aging, attempts to counteract this process seem highly relevant. In recent years, strength training has emerged as an effective method...... to induce muscle hypertrophy and increase muscle strength and functional performance in frail elderly individuals. Furthermore, there is increasing evidence that strength training is an effective method to restore muscle function in post-operative patients and in patients with chronic diseases. Despite this...

Effect of Neem Seed Husk Ash on Concrete Strength Properties ...

African Journals Online (AJOL)

Neem Seed Husk is a by-product obtained during industrial processing of Neem Seed to extract oil and produce fertilizer. Laboratory tests on Neem seed husk ash (NSHA) mixed with cement were conducted to find its effect on concrete strength and workability. Tests including slump test, compressive strength test, concrete ...

Effect of simulated pulpal pressure on composite bond strength to ...

African Journals Online (AJOL)

Statistical significance was determined by T-test (p < 0.05). There was a statistically significant difference in the mean microtensile bond strengths between the groups (p < 0.0005). Simulated pulpal pressure had a negative effect on microtensile bond strength of laser ablated dentin when Single Bond adhesive system was ...

Enhanced Flexural Strength of Tellurium Nanowires/epoxy Composites with the Reinforcement Effect of Nanowires

Science.gov (United States)

Balguri, Praveen Kumar; Harris Samuel, D. G.; Aditya, D. B.; Vijaya Bhaskar, S.; Thumu, Udayabhaskararao

2018-02-01

Investigating the mechanical properties of polymer nanocomposite materials has been greatly increased in the last decade. In particular, flexural strength plays a major role in resisting bending and shear loads of a composite material. Here, one dimensional (1D) tellurium nanowires (TeNWs) reinforced epoxy composites have been prepared and the flexural properties of resulted TeNWs/epoxy nanocomposites are studied. The diameter and length of the TeNWs used to make TeNWs/epoxy nanocomposites are 21±2.5 nm and 697±87 nm, respectively. Plain and TeNWs/epoxy nanocomposites are characterized by X-ray diffraction (XRD), thermogravimetric analysis (TGA), and differential thermal analysis (DTA). Furthermore, significant enhancement in the flexural strength of TeNWs/epoxy nanocomposite is observed in comparison to plain epoxy composite, i.e. flexural strength is increased by 65% with the addition of very little amount of TeNWs content (0.05 wt.%) to epoxy polymer. Structural details of plain and TeNWs/epoxy at micrometer scale were examined by scanning electron microscopy (SEM). We believe that our results provide a new type of semiconductor nanowires based high strength epoxy polymer nanocomposites.

Constraint effects of model coal pillar geometry on its strength

Energy Technology Data Exchange (ETDEWEB)

Wahab Khair, A.; Danqing Xu (West Virgina University, Morgantown, WV (United States))

1994-06-01

Coal and rock specimens with various diameter/height ratios (D/H) were subjected to compressive test in the laboratory. The deformation and failure characteristics of specimens were studied. The study showed that the D/H ratio of specimens significantly affects the deformation, failure characteristics, and the strength of material. The results provide a better understanding of the mechanism of D/H ratio effect on the strength of materials. The magnitude and mechanism of D/H ratio effect was compared with the effect of confining pressure, and contrasted to size effect. The application of the study to pillar design is discussed. 3 refs., 10 figs.

Identification of Bacteria and the Effect on Compressive Strength of Concrete

Directory of Open Access Journals (Sweden)

Anneza L. H.

2016-01-01

Full Text Available This paper presents the species of bacteria used in this study as well as the effect of the bacteria on compressive strength of bioconcrete. Bioconcrete is not only more environmentally friendly but it is easy to procure. The objective of this research is to identify the ureolytic bacteria and sulphate reduction bacteria that have been isolated and further use the bacteria in concrete to determine the effect of bacteria on compressive strength. Identification of bacteria is conducted through Polymerase chain reaction (PCR method and DNA sequencing. The DNA of the bacteria was run through BLAST algorithm to determine the bacterial species.The bacteria were added into the concrete mix as a partial replacement of water. 3% of water is replaced by ureolytic bacteria and 5% of water is replaced by sulphate reduction bacteria. After running BLAST algorithm the bacteria were identified as Enterococcus faecalis (ureolytic bacteria and Bacillus sp (sulphate reduction bacteria. The result of the compressive strength for control is 36.0 Mpa. Partial replacement of 3% water by ureolytic bacteria has strength of 38.2Mpa while partial replacement of 5% of water by sulphate reduction bacteria has strength of 42.5Mpa. The significant increase of compressive strength with the addition of bacteria shows that bacteria play a significant role in the improvement of compressive strength.

Estimation of RC slab-column joints effective strength using neural networks

Directory of Open Access Journals (Sweden)

A. A. Shah

Full Text Available The nominal strength of slab-column joints made of highstrength concrete (HSC columns and normal strength concrete (NSC slabs is of great importance in structural design and construction of concrete buildings. This topic has been intensively studied during the last decades. Different types of column-slab joints have been investigated experimentally providing a basis for developing design provisions. However, available data does not cover all classes of concretes, reinforcements, and possible loading cases for the proper calculation of joint stresses necessary for design purposes. New numerical methods based on modern software seem to be effective and may allow reliable prediction of column-slab joint strength. The current research is focused on analysis of available experimental data on different slab-to-column joints with the aim of predicting the nominal strength of slabcolumn joint. Neural networks technique is proposed herein using MATLAB routines developed to analyze available experimental data. The obtained results allow prediction of the effective strength of column-slab joints with accuracy and good correlation coefficients when compared to regression based models. The proposed method enables the user to predict the effective design of column-slab joints without the need for conservative safety coefficients generally promoted and used by most construction codes.

Size effects in olivine control strength in low-temperature plasticity regime

Science.gov (United States)

Kumamoto, K. M.; Thom, C.; Wallis, D.; Hansen, L. N.; Armstrong, D. E. J.; Goldsby, D. L.; Warren, J. M.; Wilkinson, A. J.

2017-12-01

The strength of the lithospheric mantle during deformation by low-temperature plasticity controls a range of geological phenomena, including lithospheric-scale strain localization, the evolution of friction on deep seismogenic faults, and the flexure of tectonic plates. However, constraints on the strength of olivine in this deformation regime are difficult to obtain from conventional rock-deformation experiments, and previous results vary considerably. We demonstrate via nanoindentation that the strength of olivine in the low-temperature plasticity regime is dependent on the length-scale of the test, with experiments on smaller volumes of material exhibiting larger yield stresses. This "size effect" has previously been explained in engineering materials as a result of the role of strain gradients and associated geometrically necessary dislocations in modifying plastic behavior. The Hall-Petch effect, in which a material with a small grain size exhibits a higher strength than one with a large grain size, is thought to arise from the same mechanism. The presence of a size effect resolves discrepancies among previous experimental measurements of olivine, which were either conducted using indentation methods or were conducted on polycrystalline samples with small grain sizes. An analysis of different low-temperature plasticity flow laws extrapolated to room temperature reveals a power-law relationship between length-scale (grain size for polycrystalline deformation and contact radius for indentation tests) and yield strength. This suggests that data from samples with large inherent length scales best represent the plastic strength of the coarse-grained lithospheric mantle. Additionally, the plastic deformation of nanometer- to micrometer-sized asperities on fault surfaces may control the evolution of fault roughness due to their size-dependent strength.

Effects of blood contamination on resin-resin bond strength.

Science.gov (United States)

Eiriksson, Sigurdur O; Pereira, Patricia N R; Swift, Edward J; Heymann, Harald O; Sigurdsson, Asgeir

2004-02-01

Incremental placement and curing of resin composites has been recommended. However, this requires longer operating time, and therefore, increased risk of contamination. The purpose of this study was to evaluate the effects of blood contamination on microtensile bond strengths (microTBS) between resin interfaces and to determine the best decontamination method to re-establish the original resin-resin bond strength. The top surfaces of 64, 4-mm composite blocks (Z-250, Renew, APX, Pertac II) were untreated as the control, or were treated as follows: blood applied and dried on the surface (Treatment 1), blood applied, rinsed, dried (Treatment 2), blood applied, rinsed, and an adhesive applied (Single Bond, One-Step, Clearfil SE, Prompt L-Pop) (Treatment 3). Fresh composite was applied and light-cured in 2-mm increments. After 24 h storage in water, the specimens were sectioned into 0.7-mm thick slabs, trimmed to a cross-sectional area of 1 mm(2), and loaded to failure at a crosshead speed of 1 mm/min using an Instron universal testing machine. Data were analyzed using two-way ANOVA and Fisher's PLSD test (pcontamination resulted in resin-resin bond strengths of only 1.0-13.1 MPa. Rinsing raised bond strengths to over 40 MPa for each material. Use of an adhesive further increased bond strengths except for Pertac II. Rinsing blood from contaminated surfaces increases the resin-resin bond strength significantly and the application of an appropriate adhesive increases the bond strength to control levels.

Effects of Strength Training Using Unstable Surfaces on Strength, Power and Balance Performance Across the Lifespan: A Systematic Review and Meta-analysis.

Science.gov (United States)

Behm, David G; Muehlbauer, Thomas; Kibele, Armin; Granacher, Urs

2015-12-01

The effectiveness of strength training on unstable surfaces (STU) versus stable surfaces (STS) or a control condition (CON; i.e., no training or regular training only) for strength, power and balance performance across the lifespan has not yet been investigated in a systematic review and meta-analysis. The aims of this systematic review and meta-analysis were to determine the general effects of STU versus STS or CON on muscle strength, power and balance in healthy individuals across the lifespan and to investigate whether performance changes following STU are age specific. A computerized systematic literature search was performed in the electronic databases PubMed and Web of Science from January 1984 up to February 2015. Initially, 209 articles were identified for review. Only controlled trials were included if they investigated STU in healthy individuals and tested at least one measure of maximal strength, strength endurance, muscle power, or static/dynamic balance. In total, 22 studies met the inclusion criteria. The included studies were coded for the following criteria: age, sex, training status, training modality, exercise and test modality. Effect size measures included within-subject standardized mean differences (SMDw) and weighted between-subject standardized mean differences (SMDb). Heterogeneity between studies was assessed using I2 and χ2 statistics. The methodological quality of each study was assessed using the Physiotherapy Evidence Database (PEDro) Scale. Our search failed to identify studies that examined the effects of STU versus STS or CON in children and middle-aged adults. However, four studies were identified that investigated the effects of STU versus CON or STS in adolescents, 15 studies were identified in young adults and three studies were identified in old adults. Compared with CON, STU produced medium effects on maximal strength in young adults and no effects to medium effects in old adults. In addition, large effects were detected on

Acute effect of different stretching methods on isometric muscle strength

Directory of Open Access Journals (Sweden)

Gabriel Vasconcellos de Lima Costa e Silva

2014-03-01

This study investigated the acute effect of static stretching methods (SS and proprioceptive neuromuscular facilitation (PNF on the static muscle strength (SMS. Eleven young male subjects with strength training experience, performed 3 tests with a 48h interval between them, randomly selected, where each one subject carried out all procedures: a hand grip without stretching; b hand grip preceded by static stretching of wrist flexors muscles; c hand grip preceded by PNF stretching of wrist flexors muscles. The Shapiro-Wilk test verified the normality of data, and a one-way ANOVA with repeated measures, followed by Tukey’s post hoc test, evaluated the differences between the groups. The significance was set at p 0.05. In conclusion, both stretching methods had caused negative effects on isometric strength, reducing its levels.

Effect of strength training on orthostatic hypotension in older adults.

Science.gov (United States)

Brilla, L R; Stephens, A B; Knutzen, K M; Caine, D

1998-01-01

This preliminary study attempted to identify the frequency of orthostatic hypotension (OH) in community dwelling older adults who volunteered to participate in an 8-week, heavy-resistance, strength-training program. It also assessed the effect of the strength-training program on OH. From a larger study (n = 53) on high-resistance strength training in older adults (mean age 71.4 +/- 6.6 years), a subset of subjects (n = 24), mean age 71.0 +/- 5.8 years, was evaluated who met at least one criterion for OH. All subjects were tested for resting blood pressures (BP) and heart rates (HR) in the supine, sitting, and standing positions. Also noted was their response to orthostatism in rising from a cot after 10 minutes and rising from a chair after 5 minutes. The subset was not different from the overall group in gender ratio, age, or effect of medication on BP. The treatment was an 8-week strength-training program at 80% of their one repetition maximum. Significant changes (P response to the orthostatic challenge, significant (P positive adaptation to an orthostatic challenge.

Effect of symmetry breaking on transition strength distributions

International Nuclear Information System (INIS)

Mitchell, G.E.; Shriner, J.F. Jr.

2001-01-01

The quantum numbers of over 100 states in 30 P have been determined from the ground state to 8 MeV. Previous measurements had provided complete spectroscopy in 26 Al. For these N=Z=odd nuclei, states of isospin T=0 and T=1 coexist at all energies. These spectra provide a unique opportunity to test the effect of symmetry breaking (of the approximate symmetry isospin) on the level statistics and on the transition strength distributions. The level statistics are strongly affected by the small symmetry breaking and the transition strength distributions differ from the Porter-Thomas distribution

Micromechanical analysis of polyacrylamide-modified concrete for improving strengths

Energy Technology Data Exchange (ETDEWEB)

Sun Zengzhi [School of Materials Science and Engineering, Chang' an University, Xi' an 710064 (China)], E-mail: zz-sun@126.com; Xu Qinwu [Pavement research, Transtec Group Inc., Austin 78731 (United States)], E-mail: qinwu_xu@yahoo.com

2008-08-25

This paper studies how polyacrylamide (PAM) alters the physicochemical and mechanical properties of concrete. The microstructure of PAM-modified concrete and the physicochemical reaction between PAM and concrete were studied through scanning electron microscope (SEM), differential thermal analysis (DTA), thermal gravimetric analysis (TGA), and infrared spectrum analysis. Meanwhile, the workability and strengths of cement paste and concrete were tested. PAM's modification mechanism was also discussed. Results indicate that PAM reacts with the Ca{sup 2+} and Al{sup 3+} cations produced by concrete hydration to form the ionic compounds and reduce the crystallization of Ca(OH){sub 2}, acting as a flexible filler and reinforcement in the porosity of concrete and, therefore, improving concrete's engineering properties. PAM also significantly alters the microstructure at the aggregate-cement interfacial transition zone. Mechanical testing results indicate that the fluidity of cement paste decreases initially, then increases, and decreases again with increasing PAM content. PAM can effectively improve the flexural strength, bonding strength, dynamic impact resistance, and fatigue life of concrete, though it reduces the compressive strength to some extent.

Micromechanical analysis of polyacrylamide-modified concrete for improving strengths

International Nuclear Information System (INIS)

Sun Zengzhi; Xu Qinwu

2008-01-01

This paper studies how polyacrylamide (PAM) alters the physicochemical and mechanical properties of concrete. The microstructure of PAM-modified concrete and the physicochemical reaction between PAM and concrete were studied through scanning electron microscope (SEM), differential thermal analysis (DTA), thermal gravimetric analysis (TGA), and infrared spectrum analysis. Meanwhile, the workability and strengths of cement paste and concrete were tested. PAM's modification mechanism was also discussed. Results indicate that PAM reacts with the Ca 2+ and Al 3+ cations produced by concrete hydration to form the ionic compounds and reduce the crystallization of Ca(OH) 2 , acting as a flexible filler and reinforcement in the porosity of concrete and, therefore, improving concrete's engineering properties. PAM also significantly alters the microstructure at the aggregate-cement interfacial transition zone. Mechanical testing results indicate that the fluidity of cement paste decreases initially, then increases, and decreases again with increasing PAM content. PAM can effectively improve the flexural strength, bonding strength, dynamic impact resistance, and fatigue life of concrete, though it reduces the compressive strength to some extent

Weibull modulus of hardness, bend strength, and tensile strength of Ni−Ta−Co−X metallic glass ribbons

Energy Technology Data Exchange (ETDEWEB)

Neilson, Henry J., E-mail: hjn2@case.edu [Case Western Reserve University, 10900 Euclid Ave, Cleveland, OH (United States); Petersen, Alex S.; Cheung, Andrew M.; Poon, S. Joseph; Shiflet, Gary J. [University of Virginia, 395 McCormick Road, P.O. Box 400745, Charlottesville, VA 22904 (United States); Widom, Mike [Carnegie Mellon University, 5000 Forbes Avenue, Wean Hall 3325, Pittsburgh, PA 15213 (United States); Lewandowski, John J. [Case Western Reserve University, 10900 Euclid Ave, Cleveland, OH (United States)

2015-05-14

In this study, the variations in mechanical properties of Ni−Co−Ta-based metallic glasses have been analyzed. Three different chemistries of metallic glass ribbons were analyzed: Ni{sub 45}Ta{sub 35}Co{sub 20}, Ni{sub 40}Ta{sub 35}Co{sub 20}Nb{sub 5}, and Ni{sub 30}Ta{sub 35}Co{sub 30}Nb{sub 5}. These alloys possess very high density (approximately 12.5 g/cm{sup 3}) and very high strength (e.g. >3 GPa). Differential scanning calorimetry (DSC) and x-ray diffraction (XRD) were used to characterize the amorphicity of the ribbons. Mechanical properties were measured via a combination of Vickers hardness, bending strength, and tensile strength for each chemistry. At least 50 tests were conducted for each chemistry and each test technique in order to quantify the variability of properties using both 2- and 3-parameter Weibull statistics. The variability in properties and their source(s) were compared to that of other engineering materials, while the nature of deformation via shear bands as well as fracture surface features have been determined using scanning electron microscopy (SEM). Toughness, the role of defects, and volume effects are also discussed.

Effect of effective grain size on Charpy impact properties of high-strength bainitic steels

International Nuclear Information System (INIS)

Shin, Sang Yong; Han, Seung Youb; Lee, Sung Hak; Hwang, Byoung Chul; Lee, Chang Gil

2008-01-01

This study is concerned with the effect of Cu and B addition on microstructure and mechanical properties of high-strength bainitic steels. Six kinds of steels were fabricated by varying alloying elements and hot-rolling conditions, and their microstructures and tensile and Charpy impact properties were investigated. Their effective grain sizes were also characterized by the electron back-scatter diffraction analysis. The tensile test results indicated that the B- or Cu-containing steels had the higher yield and tensile strengths than the B- or Cu-free steels because their volume fractions of bainitic ferrite and martensite were quite high. The B- or Cu-free steels had the higher upper shelf energy than the B- or Cu-containing steels because of their higher volume fraction of granular bainite. In the steel containing 10 ppm B without Cu, the best combination of high strengths, high upper shelf energy, and low energy transition temperature could be obtained by the decrease in the overall effective grain size due to the presence of bainitic ferrite having smaller effective grain size

Rethinking Differentiation--Using Teachers' Time Most Effectively

Science.gov (United States)

Marshall, Kim

2016-01-01

The goals of differentiation are laudable, but in recent years, many question whether it is really possible for a teacher to tailor instruction for 20 to 30 different students and whether it's desirable to differentiate by learning styles. Differentiation is just one factor in effective instruction. Supervisors who walk into a classroom looking…

The effect of thermal loads on buckling strength of cylindrical shells

International Nuclear Information System (INIS)

Kawamoto, Y.; Kodama, T.; Matsuura, S.

1993-01-01

Nuclear power plant components must be designed taking account of strong seismic loads in countries with frequent earthquakes like Japan. When designing such thin-walled shell components as a main vessel of a fast breeder reactor (FBR), one should consider the possibility that buckling might occur. In Japan, a series of buckling research has been conducted under contract with the Ministry of International Trade and Industry to develop the aseismic design method for a demonstration FBR. This study has been also done as a part of them. The problem of thermal loads on buckling strength is one of the important problems in the buckling research for FBR because axial temperature gradient is produced in a main vessel and the significant thermal stress is shown. Some studies on the effect of thermal loads on buckling strength were carried out (Brochard, 1987), (Nakamura, 1987), but its effect in the actual vessel has not been evaluated quantitatively. We have already reported the effect of thermal loads on buckling strength of a pool-type reactor vessel. (Kawamoto ,1989) In this paper, we focus on a loop-type reactor vessel and investigate the effect of thermal loads accompanying with axial temperature change near the sodium level. And the reduction of buckling strength due to the thermal loads is quantitatively evaluated

Differential TCR signals for T helper cell programming.

Science.gov (United States)

Morel, Penelope A

2018-05-02

Upon encounter with their cognate antigen naïve CD4 T cells become activated and are induced to differentiate into several possible T helper (Th) cell subsets. This differentiation depends on a number of factors including antigen presenting cells, cytokines and costimulatory molecules. The strength of the T cell receptor (TCR) signal, related to the affinity of TCR for antigen and antigen dose, has emerged as a dominant factor in determining Th cell fate. Recent studies have revealed that TCR signals of high or low strength do not simply induce quantitatively different signals in the T cells, but rather qualitatively distinct pathways can be induced based on TCR signal strength. This review examines the recent literature in this area and highlights important new developments in our understanding of Th cell differentiation and TCR signal strength. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

THE EFFECT OF PHASE CHANGE MATERIALS ON THE TENSILE STRENGTH

Directory of Open Access Journals (Sweden)

HERROELEN Thomas

2016-05-01

Full Text Available PCM’s need some important properties to have use such as high heat storage capacity, easy availability and low cost and can have different effects such as flavour, softness or exchange of heat. They are put inside of microcapsules, so they can be inbedded inside the strain, otherwise it wouldn’t be so effective. So basically the microcapsules consist of a core that’s the PCM and a polymer shell. This shell needs to be strong enough to hold the PCM and also withstand up to a certain level of heat and mechanical damage. This study investigates the tensile strength of fabrics composed by fibres, some of these fibres have benn inbedded phase change microcapsules (PCM’s. The investigated fabrics are divided by composition and by structure. By knitting the fabrics in different structures you could be able to investigate which knitting way could be the most effective to have a high tensile strength. Tensile strength tests are performed on specimens with different structures but also with different compositions which could indicate that some strains are tougher then others and more specifically if the PCM’s have a different effect on them.

Effect of Hybrid Fibers on the Mechanical Properties of High Strength Concrete

Directory of Open Access Journals (Sweden)

Hamid H. Hussein, Saeed K. Rejeb Hayder T. Abd

2014-04-01

Full Text Available In this study, high strength concrete of 75 MPa compressive strength was investigated. The experimental program was designed to study the effect of fibers and hybrid fibers (steel and polypropylene fibers on the fresh (workability and wet density and hardened properties (compressive strength, splitting strength, flexural strength and dry density of high strength concrete. Results show that decreases in slump flow of all concrete mixtures containing steel, polypropylene and hybrid fibers compared with control mix (0% fiber. Hybrid high strength concrete with steel and polypropylene fibers showed superior compressive, splitting, flexural strengths over the others concrete without or with single fibers content. The test results indicate that the maximum increase in compressive and flexural strengths are obtains with the hybridization ratio (70%steel + 30% polypropylene and were equal to 14.54% and 23.34% respectively, compared with the control mix. While, the maximum increase in splitting tensile strength with (100% steel fiber + 0 polypropylene is 21.19%. 

The effect of strength training on the testosterone level in men

Directory of Open Access Journals (Sweden)

Stanković Aleksandar

2013-01-01

Full Text Available Primary objective of this study was to provide the insight into the effects of strength training on the testosterone (TE level in men, as well as the mechanisms of anabolic effects of testosterone on human muscle apparatus, since it is known that one of the ways to increase muscle strength is through the increase of muscle mass (peripheral factor, and the basis of this process is the effect of TE. The collected data summarize the conclusions of a number of previous studies, out of which larger number of recently, and they relate to the effect of different methods of strength training (H - submaximal effort to failure, S - maximal effort, P - dynamic effort with equally applied total volume of load, and the effect of different rest periods in strength training on the level of TE in men. The presented results confirmed the claims that the H method is the most effective and reasonably called 'the method for muscle hypertrophy'. When it comes to rest periods, the ones that last for about 90 seconds proved optimal because this period had most influence on the level of lactic acid and catecholamines in blood which are considered to be the key factors for the increased secretion of TE (this hormone was included in a group of stress hormones as well. However, according to many authors, further examinations in this field are necessary in order to determine the causal link with greater certainty.

Effective axial-vector strength and β-decay systematics

Science.gov (United States)

Delion, D. S.; Suhonen, J.

2014-09-01

We use the weak axial-vector coupling strength g_{\\text{A}} as a key parameter to reproduce simultaneously the available data for both the Gamow-Teller \\beta^- and \\beta^+/\\text{EC} decay rates in nine triplets of isobars with mass numbers A=70,78,100,104,106,110,116,128,130 . We use the proton-neutron quasiparticle random-phase approximation (pnQRPA) with schematic dipole interaction containing particle-particle and particle-hole parts with mass-dependent strengths. Our analysis points to a strongly quenched effective value g_{\\text{A}}\\approx 0.3 , with a relative error of 28%. We then perform a systematic computation of 218 experimentally known \\beta^- and \\beta^+/\\text{EC} decays with quite a remarkable success. The presently extracted value of g_{\\text{A}} should be taken as an effective one, specific for a given nuclear theory framework. Present studies suggest that the effective g_{\\text{A}} is suitable for the description of decay transitions to 1^+ states at moderate excitation, below the Gamow-Teller giant resonance region.

Effects of botulinum toxin on strength-duration properties.

Science.gov (United States)

Yerdelen, Deniz; Koc, Filiz; Sarica, Yakup

2007-10-01

Axonal excitability studies have been used in several diseases to investigate the underlying pathophysiology. The threshold tracking technique was developed to measure noninvasively several indices of axonal excitability, such as strength-duration properties. This study investigated the possible effects of botulinum toxin on strength-duration time constant (SDTC) in patients with the symptoms and signs of botulism. The clinical and electrophysiological findings of 13 patients who were admitted to the authors' clinic with botulism signs and symptoms were evaluated in a 5-day period after exposure to the toxin prospectively. After routine diagnostic electroneuromyographic examinations and electromyogram with repetitive nerve stimulation at 20-50 Hz, SDTC was studied. The results were compared with 13 age- and sex-matched healthy volunteers. The SDTCs were 381 +/- 60 micros and 471 +/- 84 micros in patients and controls, respectively. There was a statistical difference between the two groups (p = .003, Mann Whitney U test). These findings suggest a possible effect of botulinum toxin, known to be effective at neuromuscular junction, on Na(+)/K(+) pump activity, and Na(+) or K(+) conductance.

Effect of Different Peat Size and Pre-Consolidation Pressure of Reconstituted Peat on Effective Undrained Shear Strength Properties

Science.gov (United States)

Azhar, ATS; Norhaliza, W.; Ismail, B.; Ezree, AM; Nizam, ZM

2017-08-01

Shear strength of the soil is one of the most important parameters in engineering design, especially during the pre- or post-construction periods, since it is mainly used to measure and evaluate the foundation or slope stability of soil. Peat normally known as a soil that has a very low value of shear strength, and in order to determine and understand the shear strength of the peat, it is a difficult task in geotechnical engineering due to several factors such as types of fabrics, the origin of the soil, water content, organic matter and the degree of humification. The aim of this study is to determine the effective undrained shear strength properties of reconstituted peat of different sizes. All the reconstituted peat samples were formed with the size that passed the opening sieve of 0.425 mm (effective undrained shear strength properties for reconstituted peat effective shear strength properties for the reconstituted peat effective undrained shear strength properties result obtained from the tests show that the reconstituted peat pore pressure, Δu, show both of strength.

Strength functions for fragmented doorway states

International Nuclear Information System (INIS)

MacDonald, W.M.

1980-01-01

Coupling a strongly excited ''doorway state'' to weak ''hallway states'' distributes its strength into micro-resonances seen in differential cross sections taken with very good energy resolution. The distribution of strength is shown to be revealed by reduced widths of the K-matrix rather than by the imaginary part of poles of the S-matrix. Different strength functions (SF) constructed by averaging the K-matrix widths are then investigated to determine their dependences on energy and on parameters related to averages of microscopic matrix elements. A new sum rule on the integrated strength of these SF is derived and used to show that different averaging procedures actually distribute the strength differently. Finally, it is shown that the discontinuous summed strength defines spreading parameters for the doorway state only in strong coupling, where it approximates the idefinite integral of the continuous SF of MacDonald-Mekjian-Kerman-De Toledo Piza. A new method of ''parametric continuation'' is used to relate a discontinuous sliding box-average, or a finite sum, of discrete terms to a continous function

Differential Effects of Sodium Butyrate and Lithium Chloride on Rhesus Monkey Trophoblast Differentiation.

Directory of Open Access Journals (Sweden)

Priyadarsini Kumar

Full Text Available Trophoblast differentiation during early placental development is critical for successful pregnancy and aberrant differentiation causes preeclampsia and early pregnancy loss. During the first trimester, cytotrophoblasts are exposed to low oxygen tension (equivalent to~2%-3% O2 and differentiation proceeds along an extravillous pathway (giving rise to invasive extravillous cytotrophoblasts and a villous pathway (giving rise to multinucleated syncytiotrophoblast. Interstitial extravillous cytotrophoblasts invade the decidua, while endovascular extravillous cytotrophoblasts are involved in re-modelling uterine spiral arteries. We tested the idea that sodium butyrate (an epigenetic modulator induces trophoblast differentiation in early gestation rhesus monkey trophoblasts through activation of the Wnt/β-catenin pathway. The results show that syncytiotrophoblast formation was increased by butyrate, accompanied by nuclear accumulation of β-catenin, and increased expression of EnvV2 and galectin-1 (two factors thought to be involved in trophoblast fusion. Surprisingly, the expression of GCM1 and syncytin-2 was not affected by sodium butyrate. When trophoblasts were incubated with lithium chloride, a GSK3 inhibitor that mimics Wnt activation, nuclear accumulation of β-catenin also occurred but differentiation into syncytiotrophoblast was not observed. Instead the cells differentiated to mononucleated spindle-shaped cells and showed molecular and behavioral characteristics of endovascular trophoblasts. Another highly specific inhibitor of GSK3, CHIR99021, failed to induce endovascular trophoblast characteristics. These observations suggest that activation of the Wnt/β-catenin pathway correlates with both trophoblast differentiation pathways, but that additional factors determine specific cell fate decisions. Other experiments suggested that the differential effects of sodium butyrate and lithium chloride might be explained by their effects on TNF�

Effects of Lifestyle on Muscle Strength in a Healthy Danish Population

DEFF Research Database (Denmark)

Bartels, Else Marie; Robertson, Samuel; Danneskiold-Samsøe, Bente

2018-01-01

The Copenhagen City Heart Study (CCHS) and measurements of Isokinetic muscle strength from a sub-study of randomly selected healthy participants from CCHS. Methods: 126 women and 63 men were studied. All participants completed a questionnaire regarding their lifestyle, including physical activity, alcohol intake...... in the lower extremities (p = 0.03) for women, and lower extremities (p = 0.03) and trunk (p = 0.007) for men. Alcohol Intake was in general not correlated to muscle strength. No clear effect of smoking was seen on muscle strength. Conclusion: Our results show that physical activity during leisure...... and smoking habits. Isokinetic muscle strength was measured over the upper extremities (UE), trunk, and lower extremities (LE). Multivariate analyses including all of the variables were carried out. Results: The level of daily physical activity during leisure was positively correlated to muscle strength...

Effects of Lifestyle on Muscle Strength in a Healthy Danish Population

DEFF Research Database (Denmark)

Bartels, Else Marie; Robertson, Samuel; Danneskiold-Samsøe, Bente

2018-01-01

The Copenhagen City Heart Study (CCHS) and measurements of Isokinetic muscle strength from a sub-study of randomly selected healthy participants from CCHS. Methods: 126 women and 63 men were studied. All participants completed a questionnaire regarding their lifestyle, including physical activity, alcohol intake...... in the lower extremities (p = 0.03) for women, and lower extremities (p = 0.03) and trunk (p = 0.007) for men. Alcohol Intake was in general not correlated to muscle strength. No clear effect of smoking was seen on muscle strength. Conclusions: Our results show that physical activity during leisure...... and smoking habits. Isokinetic muscle strength was measured over the upper extremities (UE), trunk, and lower extremities (LE). Multivariate analyses including all of the variables were carried out. Results: The level of daily physical activity during leisure was positively correlated to muscle strength...

Effects of strength training on endurance capacity in top-level endurance athletes

DEFF Research Database (Denmark)

Aagaard, Per; Andersen, Jesper L

2010-01-01

The effect of concurrent strength (S) and endurance (E) training on adaptive changes in aerobic capacity, endurance performance, maximal muscle strength and muscle morphology is equivocal. Some data suggest an attenuated cardiovascular and musculoskeletal response to combined E and S training......, while other data show unimpaired or even superior adaptation compared with either training regime alone. However, the effect of concurrent S and E training only rarely has been examined in top-level endurance athletes. This review describes the effect of concurrent SE training on short-term and long......-term endurance performance in endurance-trained subjects, ranging from moderately trained individuals to elite top-level athletes. It is concluded that strength training can lead to enhanced long-term (>30 min) and short-term (...

Effect of trapezius muscle strength on three-dimensional scapular kinematics

OpenAIRE

Turgut, Elif; Duzgun, Irem; Baltaci, Gul

2016-01-01

[Purpose] This study aimed to investigate the effect of trapezius muscle isometric strength on three-dimensional scapular kinematics in asymptomatic shoulders. [Subjects and Methods] Thirty asymptomatic subjects were included to the study. Isometric strengths of the upper, middle, and lower trapezius muscle were measured using a handheld dynamometer. Three-dimensional scapular kinematics was recorded by an electromagnetic tracking device during frontal and sagittal plane elevation. For each m...

Effect of pilates method on inspiratory and expiratory muscle strength in the elderly

Directory of Open Access Journals (Sweden)

Beatriz Mendes Tozim

2018-03-01

Full Text Available With aging, the respiratory muscle strength decreases and the pilates method is a technique that uses respiration as one of its principles. The present study has the aim of analyzing the influence of the pilates method on respiratory muscle strength in older women. For the evaluation of respiratory muscle strength (inspiratory and expiratory, manovacuometer was used. Thirty-one older women were divided into two groups: 14 participated in the pilates group and 17 in the control group. Participants of the pilates group performed 16 sessions of pilates method with an hour of training, twice week for eight weeks. The control group participated in four educational lectures for eight weeks. For statistical analysis, Shapiro-Wilk, ANOVA for repeated measures (p <0.05 and Cohen’s D index were performed. The results showed significant difference and the mean effect for the Cohen’s D index expiratory muscle strength of the pilates group when comparing before (69.71 ± 25.48 and after (85.23 ± 22.21 training (p<0.05 with an increase of 23%. The results of inspiratory muscle strength were not significant but presented an average effect for the Cohen’s D index for the pilates group before (69.71 ± 35.46 and after (88.00 ± 34.87 training, with an increase of 27%. The control group did not present significant differences for the variables evaluated. It could be concluded that the pilates method is effective in improving expiratory muscle strength and provides positive effects on the increase in inspiratory muscle strength.

EFFECTS OF CREATINE, GINSENG, AND ASTRAGALUS SUPPLEMENTATION ON STRENGTH, BODY COMPOSITION, MOOD, AND BLOOD LIPIDS DURING STRENGTH-TRAINING IN OLDER ADULTS

Directory of Open Access Journals (Sweden)

Michael E. Rogers

2006-03-01

Full Text Available The effects of supplemental dietary creatine and a botanical extract consisting of ginseng and astragalus were evaluated in 44 adults aged 55-84 years participating in a 12-week strength-training program. Participants consumed creatine only (Cr, creatine plus botanical extract (CrBE, or placebo (PL, and performed bench press, lat pull down, biceps curl, leg press, knee extension, and knee flexion for 3 sets of 8-12 reps on 3 days per week for 12 weeks. The 1-repetition maximum for each exercise, body composition (full-body DEXA, blood lipids, and mood states were evaluated before and after the intervention. Training improved (p < 0.05 strength and lean mass for all groups, however greater gains were observed with Cr and CrBE compared with placebo (but no difference was found between Cr and CrBE. Only CrBE improved blood lipids and self-reported vigor, and the CrBE group lost significantly more body fat and gained more bench press strength than Cr. These results indicate that strength and lean mass gains achieved by older adults participating in a strength training program can be enhanced with creatine supplementation, and that ginseng and astragalus may provide additional health and psychological benefits. However, these herbs do not appear to have an additive effect on strength and lean mass gains during training

Effects of different strength training frequencies on maximum strength, body composition and functional capacity in healthy older individuals.

Science.gov (United States)

Turpela, Mari; Häkkinen, Keijo; Haff, Guy Gregory; Walker, Simon

2017-11-01

There is controversy in the literature regarding the dose-response relationship of strength training in healthy older participants. The present study determined training frequency effects on maximum strength, muscle mass and functional capacity over 6months following an initial 3-month preparatory strength training period. One-hundred and six 64-75year old volunteers were randomly assigned to one of four groups; performing strength training one (EX1), two (EX2), or three (EX3) times per week and a non-training control (CON) group. Whole-body strength training was performed using 2-5 sets and 4-12 repetitions per exercise and 7-9 exercises per session. Before and after the intervention, maximum dynamic leg press (1-RM) and isometric knee extensor and plantarflexor strength, body composition and quadriceps cross-sectional area, as well as functional capacity (maximum 7.5m forward and backward walking speed, timed-up-and-go test, loaded 10-stair climb test) were measured. All experimental groups increased leg press 1-RM more than CON (EX1: 3±8%, EX2: 6±6%, EX3: 10±8%, CON: -3±6%, Ptraining frequency would induce greater benefit to maximum walking speed (i.e. functional capacity) despite a clear dose-response in dynamic 1-RM strength, at least when predominantly using machine weight-training. It appears that beneficial functional capacity improvements can be achieved through low frequency training (i.e. 1-2 times per week) in previously untrained healthy older participants. Copyright © 2017 Elsevier Inc. All rights reserved.

Effect of silicon solar cell processing parameters and crystallinity on mechanical strength

Energy Technology Data Exchange (ETDEWEB)

Popovich, V.A.; Yunus, A.; Janssen, M.; Richardson, I.M. [Delft University of Technology, Department of Materials Science and Engineering, Delft (Netherlands); Bennett, I.J. [Energy Research Centre of the Netherlands, Solar Energy, PV Module Technology, Petten (Netherlands)

2011-01-15

Silicon wafer thickness reduction without increasing the wafer strength leads to a high breakage rate during subsequent handling and processing steps. Cracking of solar cells has become one of the major sources of solar module failure and rejection. Hence, it is important to evaluate the mechanical strength of solar cells and influencing factors. The purpose of this work is to understand the fracture behavior of silicon solar cells and to provide information regarding the bending strength of the cells. Triple junctions, grain size and grain boundaries are considered to investigate the effect of crystallinity features on silicon wafer strength. Significant changes in fracture strength are found as a result of metallization morphology and crystallinity of silicon solar cells. It is observed that aluminum paste type influences the strength of the solar cells. (author)

Elastic Resistance Effectiveness on Increasing Strength of Shoulders and Hips.

Science.gov (United States)

Picha, Kelsey J; Almaddah, Muataz R; Barker, Jordan; Ciochetty, Tavis; Black, W Scott; Uhl, Tim L

2017-09-12

Elastic resistance is a common training method used to gain strength. Currently, progression with elastic resistance is based on the perceived exertion of the exercise or completion of targeted repetitions; exact resistance is typically unknown. This study's objective is to determine if knowledge of load during elastic resistance exercise will increase strength gains during exercises. Participants were randomized into two strength training groups, elastic resistance only and elastic resistance using a load cell (LC) that displays force during exercise. The LC group used a Smart Handle (Patterson Medical Supply, Chicago, IL) to complete all exercises. Each participant completed the same exercises three times weekly for 8 weeks. The LC group was provided with a set load for exercises whereas the elastic resistance only group was not. Participant's strength was tested at baseline and program completion, measuring isometric strength for shoulder abduction (SAb), shoulder external rotation (SER), hip abduction (HAb), and hip extension (HEx). Independent t-tests were used to compare the normalized torques between groups. No significant differences were found between groups. Shoulder strength gains did not differ between groups (SAb p>0.05; SER p>0.05). Hip strength gains did not differ between groups (HAb p>0.05; HEx p>0.05). Both groups increased strength due to individual supervision, constantly evaluating degree of difficulty associated with exercise and providing feedback while using elastic resistance. Using a LC is as effective as supervised training and could provide value in a clinic setting when patients are working unsupervised.

Effect of 8 weeks of free-weight and machine-based strength training on strength and power performance.

Science.gov (United States)

Wirth, Klaus; Keiner, Michael; Hartmann, Hagen; Sander, Andre; Mickel, Christoph

2016-12-01

The aim of this study was to evaluate the effectiveness of free-weight and machine-based exercises to increase different strength and speed-strength variables. One hundred twenty male participants (age: 23.8 ± 2.5 years; body height: 181.0 ± 6.8 cm; body mass: 80.2 ± 8.9 kg) joined the study. The 2 experimental groups completed an 8 week periodized strength training program that included 2 training sessions per week. The exercises that were used in the strength training programs were the parallel barbell squat and the leg press. Before and after the training period, the 1-repetition-maximum in the barbell squat and the leg press, the squat jump, the countermovement jump and unilateral isometric force (maximal isometric force and the rate of force development) were evaluated. To compare each group pre vs. post-intervention, analysis of variance with repeated measures and Scheffé post-hoc tests were used. The leg press group increased their 1-repetition-maximum significantly (p squat group such variables as 1-repetition-maximum, the squat jump and the countermovement jump increased significantly (p squat group even showed a statistically significant decrease. Differences between the 2 experimental groups were detected for the squat jump and the countermovement jump. In comparison with the leg press, the squat might be a better strength training exercise for the development of jump performance.

Effect of blasting on the strength of a rock mass

Energy Technology Data Exchange (ETDEWEB)

Muller, L

1964-01-01

Although the fact that blasting concussions tend to loosen a rock mass has always been known, the enormous reduction in strength associated with such loosening is not generally recognized. Recent investigations of the effect of blasting on a rock mass have shown that even slight loosening may markedly reduce the strength. This factor introduces a new slant on modern blasting methods, some of which will have to be considered more critically. The sensitivity of the mass to impacts depends on stress concentrations at the end of joints (Kerbspannungen) and on tensile stresses developed in the immediate vicinity of a joint, even in regions where the field stresses are not tensile. Thus, the sensitivity depends on the shape and orientation of the joints and particularly on the degree of separation of the individual joint families. The orientation of the joint families to the strains produced by blasting is just as important as the reduction in overall strength arising from the drop in friction due to the effects of the ''knocking out'' process (Foppl) on the joint body complex. Concussions may critically increase the degree of separation of the joint network thus reducing the tensile and shear strengths of the rock mass. (19 refs.)

Effect of blasting on the strength of a rock mass

Energy Technology Data Exchange (ETDEWEB)

Muller, L.

1964-01-01

Although the fact that blasting concussions tend to loosen a rock mass has always been known, the enormous reduction in strength associated with such loosening is not generally recognized. Recent investigations of the effect of blasting on a rock mass have shown that even slight loosening may markedly reduce the strength. This factor introduces a new slant on modern blasting methods, some of which will have to be considered more critically. The sensitivity of the mass to impacts depends on stress concentrations at the end of joints (Kerbspannungen) and on tensile stresses developed in the immediate vicinity of a joint, even in regions where the field stresses are not tensile. Thus, the sensitivity depends on the shape and orientation of the joints and particularly on the degree of separation of the individual joint families. The orientation of the joint families to the strains produced by blasting is just as important as the reduction in overall strength arising from the drop in friction due to the effects of the ''knocking out'' process (Foppl) on the joint body complex. Concussions may critically increase the degree of separation of the joint network thus reducing the tensile and shear strengths of the rock mass. (19 refs.)

Effect of programmed strength training on explosive strength of lower extremities in children aged 11 to 14 years

Directory of Open Access Journals (Sweden)

Atanasković Andrija

2014-01-01

Full Text Available Vertical jumps are an integral part of many sport activities. There are several factors that affect the athlete's jumping ability: strength, force and acceleration that occur when we jump. The jump is a complex and more articulated activity that requires not only strength, but great power as well. The main types of training to increase explosive strength are plyometric training and myogenic training with weight load on the lower extremities. The aim of this study was to determine the effect of myogenic training with weight load on explosive strength of the lower extremities. The first group is the control group (K, while the second group is an experimental group (E, each consisting of eighteen respondents. By Using the Myotest and performing the squat jump (SJ, the Height, Power, Force and Velocity were determined. The programme of power lasted for six weeks, twice a week for up to 60 minutes. We conclude that there is a statistically significant difference between the final and initial measurements in the experimental group, the multivariate level sig = 0.000. Increase in jump height ΔHeight = 3.28 in cm, force ΔForce = 4.68 in N/kg, the strength ΔPower = 6.18 in W/kg, the acceleration ΔVelocity = 21.8 in cm/s. The results of this study show that myogenic training with weight load has a positive impact on the explosive power of the lower extremities. This research was carried out against children aged 11 to 14 years, so we cannot say with certainty that this type of programme can have identical effects on athletes.

Effect of heating palladium-silver alloys on ceramic bond strength.

Science.gov (United States)

Li, Jie-yin; Li, Rui-nan; Chang, Shao-hai; Zhuang, Pei-lin; Liao, Juan-kun; Ye, Xiu-hua; Ye, Jian-tao

2015-11-01

The effects of different heat treatments on the internal oxidation and metal-ceramic bond in Pd-Ag alloys with different trace elements require further documentation. The purpose of this in vitro study was to determine whether heat treatment affects the metal-ceramic bond strength of 2 Pd-Ag alloys containing different trace elements. Thirteen cast specimens (25×3×0.5 mm) from each of 2 Pd-Ag alloy groups (W-1 and Argelite 61+3) were allocated to heat treatments before porcelain application: heating under reduced atmospheric pressure of 0.0014 MPa and 0.0026 MPa and heating under normal atmospheric pressure. Bond strengths were evaluated using a 3-point bending test according to ISO9693. Results were analyzed using 2-way ANOVA and Tukey HSD test (α=.05). Visual observation was used to determine the failure types of the fractured specimens. Scanning electron microscopy and energy dispersive spectroscopy were used to study morphologies, elemental compositions, and distributions in the specimens. The W-1 group had a mean bond strength significantly higher than that of Argelite 61+3 (PHeating under reduced atmospheric pressures of 0.0014 MPa and 0.0026 MPa resulted in similar bond strengths (P=.331), and both pressures had significantly higher bond strengths than that of heating under normal atmospheric pressure (P=.002, PHeating under different air pressures resulted in Pd-Ag alloys that contained either Sn or In and Ga, with various degrees of internal oxidation and different quantities of metallic nodules. Heating under reduced atmospheric pressure effectively improved the bond strength of the ceramic-to-Pd-Ag alloys. Copyright © 2015 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Effects of Strength Training on Postpubertal Adolescent Distance Runners.

Science.gov (United States)

Blagrove, Richard C; Howe, Louis P; Cushion, Emily J; Spence, Adam; Howatson, Glyn; Pedlar, Charles R; Hayes, Philip R

2018-06-01

Strength training activities have consistently been shown to improve running economy (RE) and neuromuscular characteristics, such as force-producing ability and maximal speed, in adult distance runners. However, the effects on adolescent (training on several important physiological and neuromuscular qualities associated with distance running performance. Participants (n = 25, 13 female, 17.2 ± 1.2 yr) were paired according to their sex and RE and randomly assigned to a 10-wk strength training group (STG) or a control group who continued their regular training. The STG performed twice weekly sessions of plyometric, sprint, and resistance training in addition to their normal running. Outcome measures included body mass, maximal oxygen uptake (V˙O2max), speed at V˙O2max, RE (quantified as energy cost), speed at fixed blood lactate concentrations, 20-m sprint, and maximal voluntary contraction during an isometric quarter-squat. Eighteen participants (STG: n = 9, 16.1 ± 1.1 yr; control group: n = 9, 17.6 ± 1.2 yr) completed the study. The STG displayed small improvements (3.2%-3.7%; effect size (ES), 0.31-0.51) in RE that were inferred as "possibly beneficial" for an average of three submaximal speeds. Trivial or small changes were observed for body composition variables, V˙O2max and speed at V˙O2max; however, the training period provided likely benefits to speed at fixed blood lactate concentrations in both groups. Strength training elicited a very likely benefit and a possible benefit to sprint time (ES, 0.32) and maximal voluntary contraction (ES, 0.86), respectively. Ten weeks of strength training added to the program of a postpubertal distance runner was highly likely to improve maximal speed and enhances RE by a small extent, without deleterious effects on body composition or other aerobic parameters.

Effects of replacement of binder content on bond strength of mortars

Directory of Open Access Journals (Sweden)

E. B. C. Costa

Full Text Available The reduction of binder content in cementitious systems is an effective way to mitigate environmental impacts without increasing costs. The main purpose of this study is to evaluate the effect of content binder on bond strength of mortar-brick interface. For thus, it was studied mortars produced with two limestone fines with different particle size distribution. The limestone fines were added at rates of 0% to 60% at increments of 15% as partial volume replacement of binder. Mortars were prepared in proportion of 1:3 (binder + limestone: sand in volume. The water content was kept constant and equal to 18% in relation to total weight of solids. The mechanical property of mortars was evaluated by tensile strength and the performance of interface by bond strength tests at 14 days. Results indicate that is possible make mortars with 45% less than binder without reducing bond strength. Thus, the use of appropriate particles of limestone can produce more environmentally friendly concrete and rendering mortars by reducing its binder factor without affecting its performance.

Effect of Hand Mixing on the Compressive Strength of Concrete

Directory of Open Access Journals (Sweden)

James Isiwu AGUWA

2010-12-01

Full Text Available This paper presents the effect of hand mixing on the compressive strength of concrete. Before designing the concrete mix, sieve analysis of sharp sand and chippings was carried out and their fineness moduli were determined. Also the dry weight of chippings and the specific gravities of both sand and chippings were determined. A designed concrete mix of 1:2:4 was used and the number of turnings of the mixture over from one end to another by hand mixing was varying from one time up to and including seven times. The strengths were measured at the curing ages of 7, 14, 21 and 28 days respectively using 150mm concrete cubes cast, cured and crushed. The results revealed that the compressive strengths of concrete cubes appreciably increased with increase in number of turnings from one to four times but remained almost constant beyond four times of turning for all the ages tested. For example, at 1, 2, and 3 times turning; the compressive strengths at 28 days were 4.67, 13.37 and 20.28N/mm2 respectively while at 4, 5 and 6 times turning; the compressive strengths at 28 days were 21.15, 21.34 and 21.69N/mm2. From the data, adequate strengths were not developed at turnings below three times of hand mixing, concluding that a minimum of three times turning is required to produce concrete with satisfactory strength.

Effect of zircon-based tricolor pigments on the color, microstructure, flexural strength and translucency of a novel dental lithium disilicate glass-ceramic.

Science.gov (United States)

Yuan, Kun; Wang, Fu; Gao, Jing; Sun, Xiang; Deng, Zai-Xi; Wang, Hui; Jin, Lei; Chen, Ji-Hua

2014-01-01

The purpose of this study was to investigate the effect of zircon-based tricolor pigments (praseodymium zircon yellow, ferrum zircon red, and vanadium zircon blue) on the color, thermal property, crystalline phase composition, microstructure, flexural strength, and translucency of a novel dental lithium disilicate glass-ceramic. The pigments were added to the glass frit, milled, pressed, and sintered. Ninety monochrome samples were prepared and the colors were analyzed. The effect of the pigments on thermal property, crystalline phase composition, and microstructure were determined by differential scanning calorimetry (DSC), X-ray diffraction (XRD), and scanning electron microscopy (SEM), respectively. Addition of the pigments resulted in the acquisition of subtractive primary colors as well as tooth-like colors, and did not demonstrate significant effects on the thermal property, crystalline phase composition, microstructure, and flexural strength of the experimental glass-ceramic. Although significant differences (p ceramics, the translucencies of the latter were sufficient to fabricate dental restorations. These results indicate that the zircon-based tricolor pigments can be used with dental lithium disilicate glass-ceramic to produce abundant and predictable tooth-like colors without significant adverse effects, if mixed in the right proportions. Copyright © 2013 Wiley Periodicals, Inc.

INFLUENCE OF STRENGTH TRAINING PROGRAM ON ISOMETRIC MUSCLE STRENGTH IN YOUNG ATHLETES

Directory of Open Access Journals (Sweden)

Dragan Radovanovic

2007-10-01

Full Text Available Strength training, or resistance training, is a form of physical conditioning used to increase the ability to resist force. Since muscular strength is required for success in many sports, it is logical to assume that stronger and more powerful young athletes will achieve better results. The aim of the study was to examine the effects of strength training on young athletes. An eight-week strength training program for developing muscle strength was performed in this study. Training protocol was designed specifically for young adolescent’s athletes. The program consisted of exercises for lower and upper body, abdominal and lower back muscles. The programs did not involve the maximal (1-3 repetitions maximum and other very hard intensity exercises that may had negative effect on young athletes. The results showed that strength training program had positive effects on maximal isometric muscle force (Fmax and motor skill. The increase presents the combined influence of strength training and growth.

A Comparison of Two-Stage Approaches for Fitting Nonlinear Ordinary Differential Equation Models with Mixed Effects.

Science.gov (United States)

Chow, Sy-Miin; Bendezú, Jason J; Cole, Pamela M; Ram, Nilam

2016-01-01

Several approaches exist for estimating the derivatives of observed data for model exploration purposes, including functional data analysis (FDA; Ramsay & Silverman, 2005 ), generalized local linear approximation (GLLA; Boker, Deboeck, Edler, & Peel, 2010 ), and generalized orthogonal local derivative approximation (GOLD; Deboeck, 2010 ). These derivative estimation procedures can be used in a two-stage process to fit mixed effects ordinary differential equation (ODE) models. While the performance and utility of these routines for estimating linear ODEs have been established, they have not yet been evaluated in the context of nonlinear ODEs with mixed effects. We compared properties of the GLLA and GOLD to an FDA-based two-stage approach denoted herein as functional ordinary differential equation with mixed effects (FODEmixed) in a Monte Carlo (MC) study using a nonlinear coupled oscillators model with mixed effects. Simulation results showed that overall, the FODEmixed outperformed both the GLLA and GOLD across all the embedding dimensions considered, but a novel use of a fourth-order GLLA approach combined with very high embedding dimensions yielded estimation results that almost paralleled those from the FODEmixed. We discuss the strengths and limitations of each approach and demonstrate how output from each stage of FODEmixed may be used to inform empirical modeling of young children's self-regulation.

Effect of Fluid Dynamic Viscosity on the Strength of Chalk

DEFF Research Database (Denmark)

Hedegaard, K.; Fabricius, Ida Lykke

The mechanical strength of high porosity and weakly cemented chalk is affected by the fluid in the pores. In this study, the effect of the dynamic viscosity of non-polar fluids has been measured on outcrop chalk from Sigerslev Quarry, Stevns, Denmark. The outcome is that the measured strength...... of the chalk decreases with increasing dynamic viscosity. The proposed qualitative explanation is that pressure difference supports and enhances the generation of microscopic shear and tensile failures....

Effect of concrete strength gradation to the compressive strength of graded concrete, a numerical approach

Science.gov (United States)

Pratama, M. Mirza Abdillah; Aylie, Han; Gan, Buntara Sthenly; Umniati, B. Sri; Risdanareni, Puput; Fauziyah, Shifa

2017-09-01

Concrete casting, compacting method, and characteristic of the concrete material determine the performance of concrete as building element due to the material uniformity issue. Previous studies show that gradation in strength exists on building member by nature and negatively influence the load carrying capacity of the member. A pilot research had modeled the concrete gradation in strength with controllable variable and observed that the weakest material determines the strength of graded concrete through uniaxial compressive loading test. This research intends to confirm the recent finding by a numerical approach with extensive variables of strength disparity. The finite element analysis was conducted using the Strand7 nonlinear program. The results displayed that the increase of strength disparity in graded concrete models leads to the slight reduction of models strength. A substantial difference in displacement response is encountered on the models for the small disparity of concrete strength. However, the higher strength of concrete mix in the graded concrete models contributes to the rise of material stiffness that provides a beneficial purpose for serviceability of building members.

Effect of technological parameters and microstructure on mechanical strength of UO2 fuel pellets

International Nuclear Information System (INIS)

Radford, K.

1980-01-01

The effect of various peculiarities of tablet microstructure namely, sammury porosity (tablet density), grain size and pore distribution over sizes on technological parameters, is studied. It is shown that density decrease leads to a fast reduction of UO 2 tablet strength. The maximum effect on strength is produced by pore distribution over sizes, characterized by a median size, and not by the grain size, though a combined effect of those two factors is also observed. The important role of the technology of tablet production manifests itself in the fact that all operations bringing about the increase of pore or grain sizes leads to a reduction of strength. Such factors as powder origin, granule sizes, U 3 O 8 content and the amount of additions do not cause any considerable changes in the strength of tablets. Bend tests under conditions of biaxial loading should be considered as an ideal method of determining fuel tablets strength [ru

Functional and muscular adaptations in an experimental model for isometric strength training in mice.

Directory of Open Access Journals (Sweden)

Karsten Krüger

Full Text Available Exercise training induces muscular adaptations that are highly specific to the type of exercise. For a systematic study of the differentiated exercise adaptations on a molecular level mouse models have been used successfully. The aim of the current study was to develop a suitable mouse model of isometric strength exercise training characterized by specific adaptations known from strength training. C57BL/6 mice performed an isometric strength training (ST for 10 weeks 5 days/week. Additionally, either a sedentary control group (CT or a regular endurance training group (ET groups were used as controls. Performance capacity was determined by maximum holding time (MHT and treadmill spirometry, respectively. Furthermore, muscle fiber types and diameter, muscular concentration of phosphofructokinase 1 (PFK, succinate dehydrogenase (SDHa, and glucose transporter type 4 (GLUT4 were determined. In a further approach, the effect of ST on glucose intolerance was tested in diabetic mice. In mice of the ST group we observed an increase of MHT in isometric strength tests, a type II fiber hypertrophy, and an increased GLUT4 protein content in the membrane fraction. In contrast, in mice of the ET group an increase of VO(2max, a shift to oxidative muscle fiber type and an increase of oxidative enzyme content was measured. Furthermore strength training was effective in reducing glucose intolerance in mice fed a high fat diet. An effective murine strength training model was developed and evaluated, which revealed marked differences in adaptations known from endurance training. This approach seems also suitable to test for therapeutical effects of strength training.

Effect of intracanal medicament on bond strength of fibre posts

Directory of Open Access Journals (Sweden)

Huda Melike Bayram

2016-07-01

Full Text Available The aim of this study was to evaluate the effect of calcium hydroxide (CH, triple antibiotic paste (TAP and double antibiotic paste (DAP on the push-out bond strengths of three different self-adhesive resin cements. Forty-eight single-rooted human maxillary central incisors were selected. The crowns were removed and the root canals were performed. After the irrigation protocols, the post space was prepared. The teeth were then randomly divided into a control group (no intracanal medicament and three medicament groups (n = 12 for each group. After three weeks, the medicaments were removed using 17% ethylenediaminetetraacetic acid, 2.5% sodium hypochlorite and EndoActivator agitation. The teeth were divided into three subgroups according to the fibre-post luting cement: Maxcem Elite, RelyX Unicem and BisCem. The specimens were sectioned and the push-out test was performed. One-way analysis of variance and Tukey's post hoc tests were used for statistical analyses. Regarding the type of cement, BisCem had significantly lower bond strength values than Maxcem and RelyX. There was no significant difference between the bond strength values of Maxcem and RelyX (p > 0.05. The TAP-RelyX group had the highest bond strength value and the DAP-BisCem group had the lowest bond strength value. RelyX and Maxcem had higher bond strength to root canal dentin than BisCem. The bond strength of BisCem, RelyX and Maxcem was not negatively affected by the use of DAP, CH and TAP as intracanal medicaments.

Effect of agglomerate strength on sintered density for yttria powders containing agglomerates of monosize spheres

International Nuclear Information System (INIS)

Ciftcioglu, M.; Akine, M.; Burkhart, L.

1987-01-01

The effect of agglomerate strength on sintered density was determined for several yttria powders made by intentionally agglomerating 0.1-μm, monodisperse yttriuim hydrocarbonate precursor spheres and calcining separate portions of the precursor at different temperatures to vary the strength of the intraaglomeate bonds. In this way, the effects of differences in particle morphology and other characteristics among the powders were minimized and the effect of agglomerate strength could be seen more clearly

Weight Training for Strength and Power.

Science.gov (United States)

President's Council on Physical Fitness and Sports, Washington, DC.

This paper begins by defining the terms "weight training,""weight lifting,""strength,""power," and "muscular endurance.""Weight training" is differentiated from "weight lifting" and defined as a systematic series of resistance exercises designed to promote physical development and conditioning or to rehabilitate persons who have suffered injury or…

Influence of silica fume on the strength of high strength concrete

International Nuclear Information System (INIS)

Akram, T.; Memon, S.A.; Khan, S.A.

2007-01-01

HSC (High Strength Concrete) does not become evident by a sudden change in the behavior of 'ordinary strength' concrete. There is a gradual effect that becomes more noticeable when the strength level exceeds about 40-45 MPa. There cannot be a precise level of strength which defines this change in effect. The effects are on strength and workability, requiring us to take into account in our mix proportioning, the ramifications of fineness of cement on workability and of type of aggregate and aggregate/cement ratio on strength. In fact, the selection of materials becomes more critical as the concrete strength increases and that if very high strength is required (100 MPa and higher), relatively few materials may be suitable. An experimental investigation is carried out to evaluate the feasibility of producing HSC using locally available materials and to study the influence of silica fume on the strength of HSC. The main variables in this research is amount of silica fume. The parameters that are kept constant are the amount of cement equal to 580 kg/m3, dosage of HRWRA (High Range Water Reducing Admictures) equal to 4 % by weight of cementitious materials and the ratio of fine aggregate to coarse aggregate (1:2.3). Test results revealed that it is feasible to produce HSC using locally available materials. The optimum percentage of silica fume was found to be 15 % by weight of cement. (author)

A Thermodamage Strength Theoretical Model of Ceramic Materials Taking into Account the Effect of Residual Stress

Directory of Open Access Journals (Sweden)

Weiguo Li

2012-01-01

Full Text Available A thermodamage strength theoretical model taking into account the effect of residual stress was established and applied to each temperature phase based on the study of effects of various physical mechanisms on the fracture strength of ultrahigh-temperature ceramics. The effects of SiC particle size, crack size, and SiC particle volume fraction on strength corresponding to different temperatures were studied in detail. This study showed that when flaw size is not large, the bigger SiC particle size results in the greater effect of tensile residual stress in the matrix grains on strength reduction, and this prediction coincides with experimental results; and the residual stress and the combined effort of particle size and crack size play important roles in controlling material strength.

The effect of polymer type on electric breakdown strength on a nanosecond time scale

Institute of Scientific and Technical Information of China (English)

Zhao Liang; Su Jian-Cang; Pan Ya-Feng; Zhang Xi-Bo

2012-01-01

Based on the concepts of fast polarization,effective electric field and electron impact ionization criterion,the effect of polymer type on electric breakdown strength (EBD) on a nanosecond time scale is investigated,and a formula that qualitatively characterizes the relation between the electric breakdown strength and the polymer type is derived.According to this formula,it is found that the electric breakdown strength decreases with an increase in the effective relative dielectric constants of the polymers.By calculating the effective relative dielectric constants for different types of polymers,the theoretical relation for the electric breakdown strengths of common polymers is predicted.To verify the prediction,the polymers of PE (polyethylene),PTFE (polytetrafluoroethelene),PMMA (organic glass) and Nylon are tested with a nanosecond-pulse generator.The experimental result shows EBD (PTFE) ＞ EBD (PMMA) ＞ EBD (Nylon) ＞ EBD (PE).This result is consistent with the theoretical prediction.

The effect of notches and pits on corrosion fatigue strength

Science.gov (United States)

Tatner, Ian

An investigation has been undertaken to examine the fatigue behaviour of two martensitic steels in air and aggressive environments. The steels studied are, 18% Ni marageing steel and FV520B, the later being a stainless steel turbine blade material and the former being a marageing steel that suffers general corrosion in mild environments. Both steels were heat treated to give similar tensile strength.The design and manufacture of an autoclave allowed push-pull fatigue tests to be conducted in aggressive environments at elevated temperatures.Corrosion potential was monitored using a three electrode cell and was controlled during testing. Base-line fatigue tests were conducted with a range of constant corrosion potentials, using both notched and plain FV520B specimens. In addition fatigue tests with pulsed corrosion potential were performed to asses the effect of transient corrosion conditions on the corrosion fatigue strength. The pulsed tests were designed to simulate service transients in the oxygen content and general chemical hostility in the condensing steam environment during start-up and shut down of the steam turbine.Post test examination of fractured samples was performed using Scanning Electron Microscopy (SEM) and optical microscope techniques. The fractography results were used to quantify microstructural and fracture features of the steels.A model based on the size and geometry of the initial corrosion pitting has been proposed to asses the fatigue life of FV520B in an aggressive environment.The effect of pitting on the corrosion fatigue strength of FV520B has been modelled using linear elastic fracture mechanics (LEFM) type approach. The model has shown a good correlation between predicted fatigue lives with experimental results.The results suggest that the fatigue life is governed by the mechanical stress concentrating effect of the pits rather than the electrochemical damage caused by the environment.Finite Element Analysis (FEA) of the notch allowed

The Effects of Design Strength, Fly Ash Content and Curing Method on Compressive Strength of High Volume Fly Ash Concrete: A Design of Experimental

Directory of Open Access Journals (Sweden)

Solikin Mochamad

2017-01-01

Full Text Available High volume fly ash concrete becomes one of alternatives to produce green concrete as it uses waste material and significantly reduces the utilization of Portland cement in concrete production. Although using less cement, its compressive strength is comparable to ordinary Portland cement (hereafter OPC and the its durability increases significantly. This paper reports investigation on the effect of design strength, fly ash content and curing method on compressive strength of High Volume Fly Ash Concrete. The experiment and data analysis were prepared using minitab, a statistic software for design of experimental. The specimens were concrete cylinder with diameter of 15 cm and height of 30 cm, tested for its compressive strength at 56 days. The result of the research demonstrates that high volume fly ash concrete can produce comparable compressive strength which meets the strength of OPC design strength especially for high strength concrete. In addition, the best mix proportion to achieve the design strength is the combination of high strength concrete and 50% content of fly ash. Moreover, the use of spraying method for curing method of concrete on site is still recommended as it would not significantly reduce the compressive strength result.

The Effect of CuO Nanoparticles on Antimicrobial Effects and Shear Bond Strength of Orthodontic Adhesives.

Science.gov (United States)

Toodehzaeim, Mohammad Hossein; Zandi, Hengameh; Meshkani, Hamidreza; Hosseinzadeh Firouzabadi, Azadeh

2018-03-01

Orthodontic appliances facilitate microbial plaque accumulation and increase the chance of white spot lesions. There is a need for new plaque control methods independent of patient's cooperation. The aim of this study was to determine the effects of incorporating copper oxide (CuO) nanoparticles on antimicrobial properties and bond strength of orthodontic adhesive. CuO nanoparticles were added to the composite transbond XT at concentrations of 0.01, 0.5 and 1 wt.%. To evaluate the antimicrobial properties of composites containing nanoparticles, the disk agar diffusion test was used. For this purpose, 10 discs from each concentration of nano-composites (totally 30 discs) and 10 discs from conventional composite (as the control group) were prepared. Then the diameter of streptococcus mutans growth inhibition around each disc was determined in blood agar medium. To evaluate the shear bond strength, with each concentration of nano-composites as well as the control group (conventional composite), 10 metal brackets were bonded to the human premolars and shear bond strength was determined using a universal testing machine. Nano-composites in all three concentrations showed significant antimicrobial effect compared to the control group ( p nano-composites compared to control group ( p = 0.695). Incorporating CuO nanoparticles into adhesive in all three studied concentrations added antimicrobial effects to the adhesive with no adverse effects on shear bond strength.

Effects of Kettlebell Swing vs. Explosive Deadlift Training on Strength and Power

OpenAIRE

Matthew R. Maulit; David C. Archer; Whitney D. Leyva; Cameron N. Munger; Megan A. Wong; Lee E. Brown; Jared W. Coburn; Andrew J. Galpin

2017-01-01

Background: Recent research has compared explosive deadlift to kettlebell training observing their effects on strength. The kettlebell swing is a popular practical exercise as it shares share a hip hinge movement with the explosive deadlift, but the two have not been compared. Objectives: The purpose of this study was to compare the effects of kettlebell swing vs. explosive deadlift training on strength and power. Methods: Thirty-one recreationally resistance-trained men (age = 23.1 ± 2.3 yea...

Effects of a Modified German Volume Training Program on Muscular Hypertrophy and Strength.

Science.gov (United States)

Amirthalingam, Theban; Mavros, Yorgi; Wilson, Guy C; Clarke, Jillian L; Mitchell, Lachlan; Hackett, Daniel A

2017-11-01

Amirthalingam, T, Mavros, Y, Wilson, GC, Clarke, JL, Mitchell, L, and Hackett, DA. Effects of a modified German volume training program on muscular hypertrophy and strength. J Strength Cond Res 31(11): 3109-3119, 2017-German Volume Training (GVT), or the 10 sets method, has been used for decades by weightlifters to increase muscle mass. To date, no study has directly examined the training adaptations after GVT. The purpose of this study was to investigate the effect of a modified GVT intervention on muscular hypertrophy and strength. Nineteen healthy men were randomly assign to 6 weeks of 10 or 5 sets of 10 repetitions for specific compound resistance exercises included in a split routine performed 3 times per week. Total and regional lean body mass, muscle thickness, and muscle strength were measured before and after the training program. Across groups, there were significant increases in lean body mass measures, however, greater increases in trunk (p = 0.043; effect size [ES] = -0.21) and arm (p = 0.083; ES = -0.25) lean body mass favored the 5-SET group. No significant increases were found for leg lean body mass or measures of muscle thickness across groups. Significant increases were found across groups for muscular strength, with greater increases in the 5-SET group for bench press (p = 0.014; ES = -0.43) and lat pull-down (p = 0.003; ES = -0.54). It seems that the modified GVT program is no more effective than performing 5 sets per exercise for increasing muscle hypertrophy and strength. To maximize hypertrophic training effects, it is recommended that 4-6 sets per exercise be performed, as it seems gains will plateau beyond this set range and may even regress due to overtraining.

Effect of 8 weeks of free-weight and machine-based strength training on strength and power performance

Directory of Open Access Journals (Sweden)

Wirth Klaus

2016-12-01

Full Text Available The aim of this study was to evaluate the effectiveness of free-weight and machine-based exercises to increase different strength and speed-strength variables. One hundred twenty male participants (age: 23.8 ± 2.5 years; body height: 181.0 ± 6.8 cm; body mass: 80.2 ± 8.9 kg joined the study. The 2 experimental groups completed an 8 week periodized strength training program that included 2 training sessions per week. The exercises that were used in the strength training programs were the parallel barbell squat and the leg press. Before and after the training period, the 1-repetition-maximum in the barbell squat and the leg press, the squat jump, the countermovement jump and unilateral isometric force (maximal isometric force and the rate of force development were evaluated. To compare each group pre vs. post-intervention, analysis of variance with repeated measures and Scheffé post-hoc tests were used. The leg press group increased their 1-repetition-maximum significantly (p < 0.001, while in the squat group such variables as 1-repetition-maximum, the squat jump and the countermovement jump increased significantly (p < 0.001. The maximal isometric force showed no statistically significant result for the repeated measures factor, while the rate of force development of the squat group even showed a statistically significant decrease. Differences between the 2 experimental groups were detected for the squat jump and the countermovement jump. In comparison with the leg press, the squat might be a better strength training exercise for the development of jump performance.

Effect of shelf life on compressive strength of type iv gypsum

Science.gov (United States)

Kusumastuti, K. S.; Irawan, B.; Damiyanti, M.

2017-08-01

Type IV gypsum, as a dental material for an indirect restoration’s working model, should have strength and abrasive-resistant properties. These properties depend on the product’s shelf life and its proper storage, which sometimes are easily missed by sellers. The aim of this research was to observe the effect of shelf life on the compressive strength of type IV gypsum with different production dates. Twenty cylindrical specimens were separated into two groups with different production dates and tested with a universal testing with the crosshead speed of 1 mm per minute and a load of 2,500 kgf. The data were analyzed with independent t-tests. There was a significant difference (p<0.05) in the compressive strength between the two groups with an increase in compressive strength seen in the gypsum that was stored longer.

The effect of various pozzolanic additives on the concrete strength index

Science.gov (United States)

Vitola, L.; Sahmenko, G.; Erdmane, D.; Bumanis, G.; Bajare, D.

2017-10-01

The concrete industry is searching continuously for new effective mineral additives to improve the concrete properties. Replacing cement with the pozzolanic additives in most cases has resulted not only in positive impact on the environment but also has improved strength and durability of the concrete. Effective pozzolanic additives can be obtained from natural resources such as volcanic ashes, kaolin and other sediments as well as from different production industries that create various by-products with high pozzolanic reactivity. Current research deals with effectiveness evaluation of various mineral additives/wastes, such as coal combustion bottom ash, barley bottom ash, waste glass and metakaolin containing waste as well as calcined illite clays as supplementary cementitious materials, to be used in concrete production as partial cement replacement. Most of the examined materials are used as waste stream materials with potential reactive effect on the concrete. Milling time and fineness of the tested supplementary material has been evaluated and effectiveness was detected. Results indicate that fineness of the tested materials has crucial effect on the concrete compressive strength index. Not in all cases the prolonged milling time can increase fineness and reactivity of the supplementary materials; however the optimal milling time and fineness of the pozolanic additives increased the strength index of concrete up to 1.16 comparing to reference, even in cases when cement was substituted by 20 w%.

Longitudinal analysis of the strengths and difficulties questionnaire scores of the Millennium Cohort Study children in England using M-quantile random-effects regression.

Science.gov (United States)

Tzavidis, Nikos; Salvati, Nicola; Schmid, Timo; Flouri, Eirini; Midouhas, Emily

2016-02-01

Multilevel modelling is a popular approach for longitudinal data analysis. Statistical models conventionally target a parameter at the centre of a distribution. However, when the distribution of the data is asymmetric, modelling other location parameters, e.g. percentiles, may be more informative. We present a new approach, M -quantile random-effects regression, for modelling multilevel data. The proposed method is used for modelling location parameters of the distribution of the strengths and difficulties questionnaire scores of children in England who participate in the Millennium Cohort Study. Quantile mixed models are also considered. The analyses offer insights to child psychologists about the differential effects of risk factors on children's outcomes.

Effectiveness of acute in-hospital physiotherapy with knee-extension strength training in reducing strength deficits in patients with a hip fracture

DEFF Research Database (Denmark)

Kronborg, Lise; Bandholm, Thomas; Palm, Henrik

2017-01-01

QUESTION: Is acute in-hospital physiotherapy with additional progressive knee-extension strength training (ST) of the fractured limb more effective in reducing knee-extension strength deficit at follow-up compared to physiotherapy without strength training in patients with a hip fracture? DESIGN......: Assessor blinded, randomised controlled trial with intention-to-treat analysis. PARTICIPANTS: 90 patients with a hip fracture admitted to an acute orthopaedic Hip Fracture Unit at a university hospital between October 2013 and May 2015. INTERVENTION: Daily physiotherapy with or without progressive knee...... strength training from baseline to follow-up. In the per-protocol analysis of non-missing data, significant between-group improvements by 10.5% (95% CI 0.3; 20.7) were found in favour of additional ST. No significant between-group differences were found in any secondary outcome. CONCLUSION: Physiotherapy...

Effects of Mental Imagery on Muscular Strength in Healthy and Patient Participants: A Systematic Review

Directory of Open Access Journals (Sweden)

Maamer Slimani, David Tod, Helmi Chaabene, Bianca Miarka, Karim Chamari

2016-09-01

Full Text Available The aims of the present review were to (i provide a critical overview of the current literature on the effects of mental imagery on muscular strength in healthy participants and patients with immobilization of the upper extremity (i.e., hand and anterior cruciate ligament (ACL, (ii identify potential moderators and mediators of the “mental imagery-strength performance” relationship and (iii determine the relative contribution of electromyography (EMG and brain activities, neural and physiological adaptations in the mental imagery-strength performance relationship. This paper also discusses the theoretical and practical implications of the contemporary literature and suggests possible directions for future research. Overall, the results reveal that the combination of mental imagery and physical practice is more efficient than, or at least comparable to, physical execution with respect to strength performance. Imagery prevention intervention was also effective in reducing of strength loss after short-term muscle immobilization and ACL. The present review also indicates advantageous effects of internal imagery (range from 2.6 to 136.3% for strength performance compared with external imagery (range from 4.8 to 23.2%. Typically, mental imagery with muscular activity was higher in active than passive muscles, and imagining “lifting a heavy object” resulted in more EMG activity compared with imagining “lifting a lighter object”. Thus, in samples of students, novices, or youth male and female athletes, internal mental imagery has a greater effect on muscle strength than external mental imagery does. Imagery ability, motivation, and self-efficacy have been shown to be the variables mediating the effect of mental imagery on strength performance. Finally, the greater effects of internal imagery than those of external imagery could be explained in terms of neural adaptations, stronger brain activation, higher muscle excitation, greater somatic

The effectiveness of development programming strength in primary school children

Directory of Open Access Journals (Sweden)

O.M. Khudolii

2013-07-01

Full Text Available The problems of optimizing development strength in primary school children. The purpose of the program is to validate the technology development strength abilities in the classroom physical education at school. A program of strength training by taking into account the effects of power loads. Found that the use of the combined method (option I makes it possible to obtain positive results in force readiness school classes 2-4 through 3-9 sessions. The combined method (option II significantly affects the dynamics of the forces of the local group of muscles. The use of mobile gaming allows for a higher level of emotional strength to develop the ability of students. The dynamics of power indices (option II significantly affects operation: dynamic method - 25-45 reps (rest interval between sets 30-60 seconds, the method of maximum effort - 18-30 reps (rest interval between sets 30-60 seconds method of isometric effort - 15-25 reps (rest interval between sets 30-60 seconds, the method of repeated efforts - 36-60 reps (rest interval between sets 30-60 seconds.

Effect of plastic strain on fracture strength of cracked components

International Nuclear Information System (INIS)

Kamaya, Masayuki

2009-01-01

Nuclear power plant components are occasionally subjected to large load by earthquake and may suffer plastic strain. Although the plastic strain induced in materials increases the strength, it may reduce the fracture toughness due to a crack in the components. In this study, the effect of the plastic strain on strength of cracked components was investigated. Firstly, the change in the tensile properties and fracture toughness due to plastic strain were examined for Type 316 stainless steel and carbon steel (SM490). The degree of nominal plastic strain was 5%, 10%, 20% and 40% (only for stainless steel). Secondly, the J-integral values of surface crack on a pipe were evaluated by finite element analyses. Finally, the critical load for fracture of the cracked pipe was evaluated for various pipe and crack geometries using the J-integral values and the fracture toughness obtained. It was concluded that the plastic strain enhances the fracture strength of the cracked components when the induced plastic strain is less than 10%, although the extremely large plastic strain could reduce the strength. (author)

The effectiveness of development programming strength in primary school children

Directory of Open Access Journals (Sweden)

Khudolii O.M.

2013-06-01

Full Text Available The problems of optimizing development strength in primary school children. The purpose of the program is to validate the technology development strength abilities in the classroom physical education at school. A program of strength training by taking into account the effects of power loads. Found that the use of the combined method (option I makes it possible to obtain positive results in force readiness school classes 2-4 through 3-9 sessions. The combined method (option II significantly affects the dynamics of the forces of the local group of muscles. The use of mobile gaming allows for a higher level of emotional strength to develop the ability of students. The dynamics of power indices (option II significantly affects operation: dynamic method - 25-45 reps (rest interval between sets 30-60 seconds, the method of maximum effort - 18-30 reps (rest interval between sets 30-60 seconds method of isometric effort - 15-25 reps (rest interval between sets 30-60 seconds, the method of repeated efforts - 36-60 reps (rest interval between sets 30-60 seconds.

Effect of plastic strain on fracture strength of cracked components

International Nuclear Information System (INIS)

Kamaya, Masayuki

2010-01-01

Nuclear power plant components are occasionally subjected to excessive load by earthquake and may suffer plastic strain. Although the plastic strain introduced in materials increases the strength, it may reduce the fracture toughness. In this study, the effect of the plastic strain on strength of cracked components was investigated. Firstly, the change in the tensile properties and fracture toughness due to plastic strain were examined for Type 316 stainless steel and carbon steel (SM 490). The degree of nominal plastic strain was 5%, 10%, 20% and 40% (only for stainless steel). Secondly, the J-integral values of surface crack on a pipe were evaluated by finite element analyses. Finally, the critical load for fracture of the cracked pipe was evaluated for various pipe and crack geometries using the J-integral values and the fracture toughness obtained. It was concluded that the plastic strain enhances the fracture strength of the cracked components when the induced plastic strain is less than 10%, although the extremely large plastic strain could reduce the strength. (author)

Effects of Different Environment Temperatures on Some Motor Characteristics and Muscle Strength

Science.gov (United States)

Çakir, Ergün; Yüksek, Selami; Asma, Bülent; Arslanoglu, Erkal

2016-01-01

The aim of this study was determine the effects of different environment temperatures on motor characteristics and muscle strength. 15 athletes participated to study. Flexibility, vertical jump, hand grip-leg strength, 30m sprint, 20-meter shuttle run and coordination-agility tests were measured in five different environment temperatures. (22°C,…

Line pressure effects on differential pressure measurements

International Nuclear Information System (INIS)

Neff, G.G.; Evans, R.P.

1982-01-01

The performance of differential pressure transducers in experimental pressurized water reactor (PWR) systems was evaluated. Transient differential pressure measurements made using a simple calibration proportionality relating differential pressure to output voltage could have large measurement uncertainties. A more sophisticated calibration equation was derived to incorporate the effects of zero shifts and sensitivity shifts as pressure in the pressure sensing line changes with time. A comparison made between the original calibration proportionality equation and the derived compensation equation indicates that potential measurement uncertainties can be reduced

STRENGTH OF NANOMODIFIED HIGH-STRENGTH LIGHTWEIGHT CONCRETES

Directory of Open Access Journals (Sweden)

NOZEMTСEV Alexandr Sergeevich

2013-02-01

Full Text Available The paper presents the results of research aimed at development of nanomodified high-strength lightweight concrete for construction. The developed concretes are of low average density and high ultimate compressive strength. It is shown that to produce this type of concrete one need to use hollow glass and aluminosilicate microspheres. To increase the durability of adhesion between cement stone and fine filler the authors offer to use complex nanodimensinal modifier based on iron hydroxide sol and silica sol as a surface nanomodifier for hollow microspheres. It is hypothesized that the proposed modifier has complex effect on the activity of the cement hydration and, at the same time increases bond strength between filler and cement-mineral matrix. The compositions for energy-efficient nanomodified high-strength lightweight concrete which density is 1300…1500 kg/m³ and compressive strength is 40…65 MPa have been developed. The approaches to the design of high-strength lightweight concrete with density of less than 2000 kg/m³ are formulated. It is noted that the proposed concretes possess dense homogeneous structure and moderate mobility. Thus, they allow processing by vibration during production. The economic and practical implications for realization of high-strength lightweight concrete in industrial production have been justified.

Category-length and category-strength effects using images of scenes.

Science.gov (United States)

Baumann, Oliver; Vromen, Joyce M G; Boddy, Adam C; Crawshaw, Eloise; Humphreys, Michael S

2018-06-21

Global matching models have provided an important theoretical framework for recognition memory. Key predictions of this class of models are that (1) increasing the number of occurrences in a study list of some items affects the performance on other items (list-strength effect) and that (2) adding new items results in a deterioration of performance on the other items (list-length effect). Experimental confirmation of these predictions has been difficult, and the results have been inconsistent. A review of the existing literature, however, suggests that robust length and strength effects do occur when sufficiently similar hard-to-label items are used. In an effort to investigate this further, we had participants study lists containing one or more members of visual scene categories (bathrooms, beaches, etc.). Experiments 1 and 2 replicated and extended previous findings showing that the study of additional category members decreased accuracy, providing confirmation of the category-length effect. Experiment 3 showed that repeating some category members decreased the accuracy of nonrepeated members, providing evidence for a category-strength effect. Experiment 4 eliminated a potential challenge to these results. Taken together, these findings provide robust support for global matching models of recognition memory. The overall list lengths, the category sizes, and the number of repetitions used demonstrated that scene categories are well-suited to testing the fundamental assumptions of global matching models. These include (A) interference from memories for similar items and contexts, (B) nondestructive interference, and (C) that conjunctive information is made available through a matching operation.

Effects of Mental Imagery on Muscular Strength in Healthy and Patient Participants: A Systematic Review

Science.gov (United States)

Slimani, Maamer; Tod, David; Chaabene, Helmi; Miarka, Bianca; Chamari, Karim

2016-01-01

The aims of the present review were to (i) provide a critical overview of the current literature on the effects of mental imagery on muscular strength in healthy participants and patients with immobilization of the upper extremity (i.e., hand) and anterior cruciate ligament (ACL), (ii) identify potential moderators and mediators of the “mental imagery-strength performance” relationship and (iii) determine the relative contribution of electromyography (EMG) and brain activities, neural and physiological adaptations in the mental imagery-strength performance relationship. This paper also discusses the theoretical and practical implications of the contemporary literature and suggests possible directions for future research. Overall, the results reveal that the combination of mental imagery and physical practice is more efficient than, or at least comparable to, physical execution with respect to strength performance. Imagery prevention intervention was also effective in reducing of strength loss after short-term muscle immobilization and ACL. The present review also indicates advantageous effects of internal imagery (range from 2.6 to 136.3%) for strength performance compared with external imagery (range from 4.8 to 23.2%). Typically, mental imagery with muscular activity was higher in active than passive muscles, and imagining “lifting a heavy object” resulted in more EMG activity compared with imagining “lifting a lighter object”. Thus, in samples of students, novices, or youth male and female athletes, internal mental imagery has a greater effect on muscle strength than external mental imagery does. Imagery ability, motivation, and self-efficacy have been shown to be the variables mediating the effect of mental imagery on strength performance. Finally, the greater effects of internal imagery than those of external imagery could be explained in terms of neural adaptations, stronger brain activation, higher muscle excitation, greater somatic and

Effect of cavity preparation on the flexural strengths of acrylic resin repairs

Science.gov (United States)

ELHADIRY, Safa Salim; YUNUS, Norsiah; ARIFFIN, Yusnidar Tajul

2010-01-01

Objective To investigate the effect of cavity preparation on the flexural strength of heat-curing denture resin when repaired with an auto-curing resin. Material and methods Ninety-six rectangular specimens (64x10x2.5 mm) prepared from heat-curing denture base resin (Meliodent) were randomly divided into four groups before repair. One group was left intact as control. Each repair specimen was sectioned into two; one group was repaired using the conventional repair method (Group 1). Two groups had an additional transverse cavity (2x3.5x21.5 mm) prepared prior to the repair; one repaired with (Group 2) and one without glass-fiber reinforcement (Group 3). A three-point flexural bending test according to the ISO 1567:1999 specification8 for denture base polymers was carried out on all groups after 1, 7 and 30 days of water immersion. Statistical analysis was carried out using two-way ANOVA, Kruskal Wallis and post-hoc Mann Whitney tests. Results The highest flexural strength was observed in the control group. Control and conventional repairs group (Group 1) showed reduction in the flexural strength 30 days after water immersion. No significant change in the strength was observed for Groups 2 and 3 where the repair joints were similarly prepared with additional transverse cavity. Conclusion Repaired specimens showed lower flexural strength values than intact heat-curing resin. Cavity preparation had no significant effect on the flexural strength of repair with water immersion. PMID:21308283

Global model for the lithospheric strength and effective elastic thickness

Science.gov (United States)

Tesauro, Magdala; Kaban, Mikhail K.; Cloetingh, Sierd A. P. L.

2013-08-01

Global distribution of the strength and effective elastic thickness (Te) of the lithosphere are estimated using physical parameters from recent crustal and lithospheric models. For the Te estimation we apply a new approach, which provides a possibility to take into account variations of Young modulus (E) within the lithosphere. In view of the large uncertainties affecting strength estimates, we evaluate global strength and Te distributions for possible end-member 'hard' (HRM) and a 'soft' (SRM) rheology models of the continental crust. Temperature within the lithosphere has been estimated using a recent tomography model of Ritsema et al. (2011), which has much higher horizontal resolution than previous global models. Most of the strength is localized in the crust for the HRM and in the mantle for the SRM. These results contribute to the long debates on applicability of the "crème brulée" or "jelly-sandwich" model for the lithosphere structure. Changing from the SRM to HRM turns most of the continental areas from the totally decoupled mode to the fully coupled mode of the lithospheric layers. However, in the areas characterized by a high thermal regime and thick crust, the layers remain decoupled even for the HRM. At the same time, for the inner part of the cratons the lithospheric layers are coupled in both models. Therefore, rheological variations lead to large changes in the integrated strength and Te distribution in the regions characterized by intermediate thermal conditions. In these areas temperature uncertainties have a greater effect, since this parameter principally determines rheological behavior. Comparison of the Te estimates for both models with those determined from the flexural loading and spectral analysis shows that the 'hard' rheology is likely applicable for cratonic areas, whereas the 'soft' rheology is more representative for young orogens.

The effects of sterilization on the tensile strength of orthodontic wires.

Science.gov (United States)

Staggers, J A; Margeson, D

1993-01-01

The purpose of this study was to evaluate the effect of sterilization on the tensile strength of 0.016" beta-titanium, nickel titanium and stainless steel wires. Three common methods of sterilization--autoclaving, dry heat and ethylene oxide--were evaluated in three test trials involving zero, one and five sterilization cycles. For each of the test trials, five pieces each of 0.016" TMA, 0.016" Sentalloy and 0.016" Tru-chrome stainless steel wires were sterilized using a standard autoclave. Five other pieces of each of the same wires were sterilized in a dryclave, while an additional five pieces of each of the three wire types were sterilized using ethylene oxide. The ultimate tensile strengths of the wires were then determined using an Instron Universal Testing Machine. The data were compared for statistical differences using analysis of variance. The results showed that dry heat sterilization significantly increased the tensile strength of TMA wires after one cycle, but not after five cycles. Autoclaving and ethylene oxide sterilization did not significantly alter the tensile strength of TMA wires. Dry heat and autoclave sterilization also significantly increased the tensile strength of Sentalloy wires, but the mean strength after five sterilization cycles was not significantly different than after one cycle. Ethylene oxide sterilization of Sentalloy wires did not significantly alter the tensile strengths of that wire. There were no significant differences in the tensile strengths of the stainless steel wires following zero, one or five cycles for any of the sterilization methods.

Effect of wear on the burst strength of l-80 steel casing

International Nuclear Information System (INIS)

Irawan, S; Bharadwaj, A M; Temesgen, B; Karuppanan, S; Abdullah, M Z B

2015-01-01

Casing wear has recently become one of the areas of research interest in the oil and gas industry especially in extended reach well drilling. The burst strength of a worn out casing is one of the significantly affected mechanical properties and is yet an area where less research is done The most commonly used equations to calculate the resulting burst strength after wear are Barlow, the initial yield burst, the full yield burst and the rupture burst equations. The objective of this study was to estimate casing burst strength after wear through Finite Element Analysis (FEA). It included calculation and comparison of the different theoretical bursts pressures with the simulation results along with effect of different wear shapes on L-80 casing material. The von Misses stress was used in the estimation of the burst pressure. The result obtained shows that the casing burst strength decreases as the wear percentage increases. Moreover, the burst strength value of the casing obtained from the FEA has a higher value compared to the theoretical burst strength values. Casing with crescent shaped wear give the highest burst strength value when simulated under nonlinear analysis. (paper)

Constitutive β-catenin activation in osteoblasts impairs terminal osteoblast differentiation and bone quality

Energy Technology Data Exchange (ETDEWEB)

Bao, Quanwei; Chen, Sixu; Qin, Hao [State Key Laboratory of Trauma, Burn and Combined injury, Department of Trauma Surgery, Daping Hospital, Third Military Medical University, ChongQing 400042 (China); Feng, Jianquan [Department of Biomedical Sciences, Baylor College of Dentistry, Texas A& M Health Science Center, Dallas, TX 75246 (United States); Liu, Huayu; Liu, Daocheng; Li, Ang; Shen, Yue; Zhong, Xiaozheng; Li, Junfeng [State Key Laboratory of Trauma, Burn and Combined injury, Department of Trauma Surgery, Daping Hospital, Third Military Medical University, ChongQing 400042 (China); Zong, Zhaowen, E-mail: zongzhaowen@sina.cn [State Key Laboratory of Trauma, Burn and Combined injury, Department of Trauma Surgery, Daping Hospital, Third Military Medical University, ChongQing 400042 (China)

2017-01-01

Accumulating evidence suggests that Wnt/β-catenin signaling plays a central role in controlling bone mass. We previously reported that constitutive activation of β-catenin (CA-β-catenin) in osteoblasts potentially has side effects on the bone growth and bone remodeling process, although it could increase bone mass. The present study aimed to observe the effects of osteoblastic CA-β-catenin on bone quality and to investigate possible mechanisms of these effects. It was found that CA-β-catenin mice exhibited lower mineralization levels and disorganized collagen in long bones as confirmed by von Kossa staining and sirius red staining, respectively. Also, bone strength decreased significantly in CA-β-catenin mice. Then the effect of CA-β-catenin on biological functions of osteoblasts were investigated and it was found that the expression levels of osteocalcin, a marker for the late differentiation of osteoblasts, decreased in CA-β-catenin mice, while the expression levels of osterix and alkaline phosphatase, two markers for the early differentiation of osteoblasts, increased in CA-β-catenin mice. Furthermore, higher proliferation rate were revealed in osteoblasts that were isolated from CA-β-catenin mice. The Real-time PCR and western blot examination found that the expression level of c-myc and cyclin D1, two G1 progression-related molecules, increased in osteoblasts that were isolated from the CA-β-catenin mice, and the expression levels of CDK14 and cyclin Y, two mitotic-related molecules that can accelerate cells entering into S and G2/M phases, increased in osteoblasts that were isolated from the CA-β-catenin mice. In summary, osteoblastic CA-β-catenin kept osteoblasts in high proliferative state and impaired the terminal osteoblast differentiation, and this led to changed bone structure and decreased bone strength. - Highlights: • Wnt/β-catenin signaling plays a central role in controlling bone mass. • CA-β-catenin has side effects on the bone

The Immediate Effect of Neuromuscular Joint Facilitation (NJF) Treatment on Hip Muscle Strength.

Science.gov (United States)

Wang, Hongdan; Huo, Ming; Huang, Qiuchen; Li, Desheng; Maruyama, Hitoshi

2013-11-01

[Purpose] This study investigated the change in hip muscle strength of younger persons after neuromuscular joint facilitation (NJF) treatment. [Subjects] The subjects were 45 healthy young people, who were divided into two groups: a NJF group and a proprioceptive neuromuscular facilitation (PNF) group. The NJF group consisted of 21 subjects (11 males, 10 females), and the PNF group consisted of 24 subjects (11 males, 13 females). [Methods] Participants in the NJF group received NJF treatment. We measured the maximal flexor strength and the maximal extensor strength during isokinetic movement of the hip joint before and after intervention in both groups. The angular velocities used were 60°/sec and 180°/sec. [Results] The NJF group showed significant increases in the maximal flexor strength and the maximal extensor strength after the intervention at each angular velocity. In the PNF group, the maximal flexor strength of 60°/sec and the maximal extensor strength of 180°/sec were significant increases. [Conclusion] These results suggest that there is an immediate effect of NJF intervention on hip muscle strength.

Effects of hippotherapy on mobility, strength and balance in elderly.

Science.gov (United States)

de Araújo, Thais Borges; de Oliveira, Ricardo Jacó; Martins, Wagner Rodrigues; de Moura Pereira, Marcio; Copetti, Fernando; Safons, Marisete Peralta

2013-01-01

To assess the chronic effects of hippotherapy on functional mobility, muscle strength and balance in elderly. 28 volunteers, between the age of 60 and 84, were randomly recruited and divided in experimental group (EG), with 12 individuals (8 women and 4 men) and control group (CG), with 16 individuals (14 women and 2 men). The EG group participated in an 8-week hippotherapy program. Before and after the study period functional mobility was assessed and measured by Time Up and Go Test (TUG), muscle strength of the lower limbs was measured by 30s Chair Stand Test (30CST) and performance in balance was measured by the Berg Balance Scale (BBS). A mixed ANOVA model (group×testing time) was applied to establish the effect of the different groups on the functional variables. The functional capacity of the EG group was increased if compared to CG group after the intervention of the BBS (p=0.003) and 30CST (p=0.032), but not of the TUG (p=0.063). The results indicated that hippotherapy improves the lower limb strength and balance in elderly. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

Effects of caffeine intake on muscle strength and power: a systematic review and meta-analysis.

Science.gov (United States)

Grgic, Jozo; Trexler, Eric T; Lazinica, Bruno; Pedisic, Zeljko

2018-01-01

Caffeine is commonly used as an ergogenic aid. Literature about the effects of caffeine ingestion on muscle strength and power is equivocal. The aim of this systematic review and meta-analysis was to summarize results from individual studies on the effects of caffeine intake on muscle strength and power. A search through eight databases was performed to find studies on the effects of caffeine on: (i) maximal muscle strength measured using 1 repetition maximum tests; and (ii) muscle power assessed by tests of vertical jump. Meta-analyses of standardized mean differences (SMD) between placebo and caffeine trials from individual studies were conducted using the random effects model. Ten studies on the strength outcome and ten studies on the power outcome met the inclusion criteria for the meta-analyses. Caffeine ingestion improved both strength (SMD = 0.20; 95% confidence interval [CI]: 0.03, 0.36; p  = 0.023) and power (SMD = 0.17; 95% CI: 0.00, 0.34; p  = 0.047). A subgroup analysis indicated that caffeine significantly improves upper (SMD = 0.21; 95% CI: 0.02, 0.39; p  = 0.026) but not lower body strength (SMD = 0.15; 95% CI: -0.05, 0.34; p  = 0.147). The meta-analyses showed significant ergogenic effects of caffeine ingestion on maximal muscle strength of upper body and muscle power. Future studies should more rigorously control the effectiveness of blinding. Due to the paucity of evidence, additional findings are needed in the female population and using different forms of caffeine, such as gum and gel.

Experimental knee joint pain during strength training and muscle strength gain in healthy subjects

DEFF Research Database (Denmark)

Sørensen, T J; Langberg, Henning; Hodges, P W

2012-01-01

Knee joint pain and reduced quadriceps strength are cardinal symptoms in many knee pathologies. In people with painful knee pathologies, quadriceps exercise reduces pain, improves physical function, and increases muscle strength. A general assumption is that pain compromises muscle function...... and thus may prevent effective rehabilitation. This study evaluated the effects of experimental knee joint pain during quadriceps strength training on muscle strength gain in healthy individuals....

Effect of composite warming on shear bond strength.

Science.gov (United States)

McDaniel, Thomas F; Sigrist, Thomas W; Johnson, Gary M

2018-01-01

Several manufacturers produce devices designed to warm composite resins used in restorative dentistry. Previous investigators have examined the effects of heating composite restorative resins prior to placement and polymerization. Heating has been reported to reduce viscosity, improve ease of placement, enhance monomer conversion, and reduce microleakage. The aim of the present study was to compare shear bond strengths of room temperature (22°C) and prewarmed (54°C) restorative composite resin. Extracted bovine mandibular incisors were sectioned sagittally and embedded in acrylic cylinders. Enamel was selectively etched with 37% phosphoric acid, rinsed, and dried. Self-etching primer was applied to both enamel and dentin. Self-etching adhesive was then applied and photopolymerized. Composite resin capsules were then divided into prewarmed and room temperature groups. Fourteen composite specimens prewarmed in an incubator were applied to the prepared enamel and dentin and photopolymerized. Fourteen room temperature composite specimens were likewise placed. After storage in water for 24 hours, all composite specimens were subjected to shear stress testing. The resulting data were analyzed with a t test (P = 0.05). There was no statistically significant difference between the shear bond strengths of the prewarmed and room temperature composite resin specimens. Warming does not appear to affect bond strength of composite resin bonded to both dentin and enamel.

From Mind to Body: Is Mental Practice Effective on Strength Gains? A Meta-Analysis.

Science.gov (United States)

Manochio, João Paulo; Lattari, Eduardo; Portugal, Eduardo Matta Mello; Monteiro-Junior, Renato Sobral; Paes, Flávia; Budde, Henning; de Tarso Veras Farinatti, Paulo; Arias-Carrión, Oscar; Wegner, Mirko; Carta, Mauro Giovanni; Mura, Gioia; Ferreira Rocha, Nuno Barbosa; Almada, Leonardo Ferreira; Nardi, Antonio Egidio; Yuan, Ti-Fei; Machado, Sergio

2015-01-01

Mental practice is an internal reproduction of a motor act (whose intention is to promote learning and improving motor skills). Some studies have shown that other cognitive strategies also increase the strength and muscular resistance in healthy people by the enhancement of the performance during dynamic tasks. Mental training sessions may be primordial to improving muscle strength in different subjects. The aim of this study was to systematically review and meta-analiyze studies that assessed whether mental practice is effective in improving muscular strength. We conducted an electronic-computed search in Pub-Med/Medline and ISI Web of Knowledge, Scielo and manual searchs, searching papers written in English between 1991 and 2014. There were 44 studies in Pub-Med/Medline, 631 in ISI Web of Knowledge, 11 in Scielo and 3 in manual searchs databases. After exclusion of studies for duplicate, unrelated to the topic by title and summary, different samples and methodologies, a meta-analysis of 4 studies was carried out to identify the dose-response relationship. We did not find evidence that mental practice is effective in increasing strength in healthy individuals. There is no evidence that mental practice alone can be effective to induce strength gains or to optimize the training effects.

Effects of weightlifting vs. kettlebell training on vertical jump, strength, and body composition.

Science.gov (United States)

Otto, William H; Coburn, Jared W; Brown, Lee E; Spiering, Barry A

2012-05-01

Effects of weightlifting vs. kettlebell training on vertical jump, strength, and body composition. J Strength Cond Res 26(5): 1199-1202, 2012-The present study compared the effects of 6 weeks of weightlifting plus traditional heavy resistance training exercises vs. kettlebell training on strength, power, and anthropometric measures. Thirty healthy men were randomly assigned to 1 of 2 groups: (a) weightlifting (n = 13; mean ± SD: age, 22.92 ± 1.98 years; body mass, 80.57 ± 12.99 kg; height, 174.56 ± 5.80 cm) or (b) kettlebell (n = 17; mean ± SD: age, 22.76 ± 1.86 years; body mass, 78.99 ± 10.68 kg; height, 176.79 ± 5.08 cm) and trained 2 times a week for 6 weeks. A linear periodization model was used for training; at weeks 1-3 volume was 3 × 6 (kettlebell swings or high pull), 4 × 4 (accelerated swings or power clean), and 4 × 6 (goblet squats or back squats), respectively, and the volume increased during weeks 4-6 to 4 × 6, 6 × 4, and 4 × 6, respectively. Participants were assessed for height (in centimeters), body mass (in kilograms), and body composition (skinfolds). Strength was assessed by the back squat 1 repetition maximum (1RM), whereas power was assessed by the vertical jump and power clean 1RM. The results of this study indicated that short-term weightlifting and kettlebell training were effective in increasing strength and power. However, the gain in strength using weightlifting movements was greater than that during kettlebell training. Neither method of training led to significant changes in any of the anthropometric measures. In conclusion, 6 weeks of weightlifting induced significantly greater improvements in strength compared with kettlebell training. No between-group differences existed for the vertical jump or body composition.

The Effects of Design Strength, Fly Ash Content and Curing Method on Compressive Strength of High Volume Fly Ash Concrete: A Design of Experimental

OpenAIRE

Solikin Mochamad; Setiawan Budi

2017-01-01

High volume fly ash concrete becomes one of alternatives to produce green concrete as it uses waste material and significantly reduces the utilization of Portland cement in concrete production. Although using less cement, its compressive strength is comparable to ordinary Portland cement (hereafter OPC) and the its durability increases significantly. This paper reports investigation on the effect of design strength, fly ash content and curing method on compressive strength of High Volume Fly ...

Effects of bioDensity Training and Power Plate Whole-Body Vibration on Strength, Balance, and Functional Independence in Older Adults.

Science.gov (United States)

Smith, Derek T; Judge, Stacey; Malone, Ashley; Moynes, Rebecca C; Conviser, Jason; Skinner, James S

2016-01-01

Reduced strength, balance, and functional independence diminish quality of life and increase health care costs. Sixty adults (82.2 ± 4.9 years) were randomized to a control or three 12-week intervention groups: bioDensity (bD); Power Plate (PP) whole-body vibration (WBV); or bD+PP. bD involved one weekly 5-s maximal contraction of four muscle groups. PP involved two 5-min WBV sessions. Primary outcomes were strength, balance, and Functional Independence Measure (FIM). No groups differed initially. Strength significantly increased 22-51% for three muscle groups in bD and bD+PP (P Balance significantly improved in PP and bD+PP but not in control or bD. bD, PP, and bD+PP differentially improved FIM self-care and mobility. Strength improvements from weekly 5-min sessions of bD may impart health/clinical benefits. Balance and leg strength improvements suggest WBV beneficially impacts fall risk and incidence. Improved FIM scores are encouraging and justify larger controlled trials on bD and bD+PP efficacy.

Contrast and strength of visual memory and imagery differentially affect visual perception.

Science.gov (United States)

Saad, Elyana; Silvanto, Juha

2013-01-01

Visual short-term memory (VSTM) and visual imagery have been shown to modulate visual perception. However, how the subjective experience of VSTM/imagery and its contrast modulate this process has not been investigated. We addressed this issue by asking participants to detect brief masked targets while they were engaged either in VSTM or visual imagery. Subjective experience of memory/imagery (strength scale), and the visual contrast of the memory/mental image (contrast scale) were assessed on a trial-by-trial basis. For both VSTM and imagery, contrast of the memory/mental image was positively associated with reporting target presence. Consequently, at the sensory level, both VSTM and imagery facilitated visual perception. However, subjective strength of VSTM was positively associated with visual detection whereas the opposite pattern was found for imagery. Thus the relationship between subjective strength of memory/imagery and visual detection are qualitatively different for VSTM and visual imagery, although their impact at the sensory level appears similar. Our results furthermore demonstrate that imagery and VSTM are partly dissociable processes.

Contrast and strength of visual memory and imagery differentially affect visual perception.

Directory of Open Access Journals (Sweden)

Elyana Saad

Full Text Available Visual short-term memory (VSTM and visual imagery have been shown to modulate visual perception. However, how the subjective experience of VSTM/imagery and its contrast modulate this process has not been investigated. We addressed this issue by asking participants to detect brief masked targets while they were engaged either in VSTM or visual imagery. Subjective experience of memory/imagery (strength scale, and the visual contrast of the memory/mental image (contrast scale were assessed on a trial-by-trial basis. For both VSTM and imagery, contrast of the memory/mental image was positively associated with reporting target presence. Consequently, at the sensory level, both VSTM and imagery facilitated visual perception. However, subjective strength of VSTM was positively associated with visual detection whereas the opposite pattern was found for imagery. Thus the relationship between subjective strength of memory/imagery and visual detection are qualitatively different for VSTM and visual imagery, although their impact at the sensory level appears similar. Our results furthermore demonstrate that imagery and VSTM are partly dissociable processes.

Effect of bitumen emulsion on setting, strength, soundness and ...

Indian Academy of Sciences (India)

Unknown

Effect of bitumen emulsion on setting, strength, soundness and moisture resistance of oxychloride cement. M P S CHANDRAWAT†, T N OJHA and R N YADAV*. Department of Chemistry, R N Ruia Government College, Ramgarh-Shekhawati (Sikar) 331 024, India. †Department of Chemistry, R R Government College, ...

Monitoring the effect of football match congestion on hamstring strength and lower limb flexibility

DEFF Research Database (Denmark)

Wollin, Martin; Thorborg, Kristian; Pizzari, Tania

2018-01-01

OBJECTIVES: To investigate the effect of competitive football match congestion on hamstring strength and lower limb flexibility. DESIGN: Repeated measures. SETTING: Elite male youth football. PARTICIPANTS: Fifteen male elite youth football players from the national football association centre of ....... CONCLUSION: Isometric hamstring strength and pain can be considered for inclusion in-season to monitor player's post-match hamstring recovery characteristics during congested match fixtures.......OBJECTIVES: To investigate the effect of competitive football match congestion on hamstring strength and lower limb flexibility. DESIGN: Repeated measures. SETTING: Elite male youth football. PARTICIPANTS: Fifteen male elite youth football players from the national football association centre...... of excellence were included (age = 15.81 ±0.65 years, height = 171.95 ±6.89 cm, weight = 65.93 ±7.53 kg). MAIN OUTCOME MEASURES: Hamstring strength and pain, ankle dorsiflexion, hip extension, knee extension and flexion range of motion. RESULTS: Hamstring strength was highest at baseline and significantly...

Effects of Agar Gel Strength and Fat on Oral Breakdown, Volatile Release, and Sensory Perception Using in Vivo and in Vitro Systems.

Science.gov (United States)

Frank, Damian; Eyres, Graham T; Piyasiri, Udayasika; Cochet-Broch, Maeva; Delahunty, Conor M; Lundin, Leif; Appelqvist, Ingrid M

2015-10-21

The density and composition of a food matrix affect the rates of oral breakdown and in-mouth flavor release as well as the overall sensory experience. Agar gels of increasing concentration (1.0, 1.7, 2.9, and 5% agarose) with and without added fat (0, 2, 5, and 10%) were spiked with seven aroma volatiles. Differences in oral processing and sensory perception were systematically measured by a trained panel using a discrete interval time intensity method. Volatile release was measured in vivo and in vitro by proton transfer reaction mass spectrometry. Greater oral processing was required as agar gel strength increased, and the intensity of flavor-related sensory attributes decreased. Volatile release was inversely related to gel strength, showing that physicochemical phenomena were the main mechanisms underlying the perceived sensory changes. Fat addition reduced the amount of oral processing and had differential effects on release, depending on the fat solubility or lipophilicity of the volatiles.

Effect of a New Salivary Contaminant Removal Method on Bond Strength

Science.gov (United States)

2014-08-31

was to evaluate the effect of various salivary- contaminant removal methods on the shear bond strength of resin cement to hydrofluoric-acid (HF) etched...mold (Ultradent) to a height of 3mm and light cured . Specimens were stored for 24 hours in 37°C distilled water and then tested in shear in a... contamination which may compromise the bond strength of the resin cement to the ceramic (Aboush, 1998; van Schalkwyk et al., 2003). Saliva affects bond

Compressive and flexural strength of high strength phase change mortar

Science.gov (United States)

Qiao, Qingyao; Fang, Changle

2018-04-01

High-strength cement produces a lot of hydration heat when hydrated, it will usually lead to thermal cracks. Phase change materials (PCM) are very potential thermal storage materials. Utilize PCM can help reduce the hydration heat. Research shows that apply suitable amount of PCM has a significant effect on improving the compressive strength of cement mortar, and can also improve the flexural strength to some extent.

Effect of bentonite addition on residual strength of microwave-hardened waterglass-containing moulding sands

Directory of Open Access Journals (Sweden)

M. Stachowicz

2011-07-01

Full Text Available The paper presents results of a preliminary research of the effect of bentonite addition on residual strength of microwave-hardened moulding sands, containing sodium waterglass. Strength was determined at ambient temperature, on cylindrical specimens baked in an oven. Moulding sands for examinations were based on high-silica sand with addition of 2.5 % of non-modified, domestic-made waterglass grade 145. The prepared standard cylindrical specimens were hardened using the innovative microwave heating process and next baked for 30 minutes at temperatures between 100 and 1200 °C. Strength parameters of the specimens were determined on the specimens cooled- down to ambient temperature. The obtained results were compared with literature data to evaluate the effect of the applied hardening method and of the special additive on residual strength as a function of baking temperature. A favourable effect was found of both the innovative heating process and the applied bentonite addition.

Sink strengths of dislocations taking into account bulk recombination effects

International Nuclear Information System (INIS)

Steinbach, E.

1988-01-01

The applicability of the rate theory to describe radiation damage processes is closely associated with the calculation of the various sink strengths. In this connection the effect of bulk recombination is usually neglected, because of the complexity of the problem. For this reason we present in this paper, for the first time, by means of the rigorous elastic-field model of a dislocation embedded in a lossy continuum, analytic expressions for the diffusion flux of irradiation-induced point defects into a dislocation, taking into account the elastic interaction, additional sinks and higher order bulk recombination effects. The resulting self-consistent formulae for the dislocation sink strengths clearly demonstrate the importance of the bulk recombination for the micro-structures of irradiated materials. In conjunction with the Harwell computer code VS5 it became clear that this new dislocation bias also leads to a change in the macrostructural observables. The order of magnitude of this effect emphasizes that neglecting bulk recombination as a general principle is not justified

Effects of yoga, strength training and advice on back pain: a randomized controlled trial.

Science.gov (United States)

Brämberg, Elisabeth Björk; Bergström, Gunnar; Jensen, Irene; Hagberg, Jan; Kwak, Lydia

2017-03-29

Among the working population, non-specific low-back pain and neck pain are one of the most common reasons for sickness absenteeism. The aim was to evaluate the effects of an early intervention of yoga - compared with strength training or evidence-based advice - on sickness absenteeism, sickness presenteeism, back and neck pain and disability among a working population. A randomized controlled trial was conducted on 159 participants with predominantly (90%) chronic back and neck pain. After screening, the participants were randomized to kundalini yoga, strength training or evidence-based advice. Primary outcome was sickness absenteeism. Secondary outcomes were sickness presenteeism, back and neck pain and disability. Self-reported questionnaires and SMS text messages were completed at baseline, 6 weeks, 6 and 12 months. The results did not indicate that kundalini yoga and strength training had any statistically significant effects on the primary outcome compared with evidence-based advice. An interaction effect was found between adherence to recommendations and sickness absenteeism, indicating larger significant effects among the adherers to kundalini yoga versus evidence-based advice: RR = 0.47 (CI 0.30; 0.74, p = 0.001), strength training versus evidence-based advice: RR = 0.60 (CI 0.38; 0.96, p = 0.032). Some significant differences were also found for the secondary outcomes to the advantage of kundalini yoga and strength training. Guided exercise in the forms of kundalini yoga or strength training does not reduce sickness absenteeism more than evidence-based advice alone. However, secondary analyses reveal that among those who pursue kundalini yoga or strength training at least two times a week, a significantly reduction in sickness absenteeism was found. Methods to increase adherence to treatment recommendations should be further developed and applied in exercise interventions. Clinicaltrials.gov NCT01653782, date of registration: June, 28

The differential susceptibility to media effects model

NARCIS (Netherlands)

Valkenburg, P.M.; Peter, J.

2013-01-01

In this theoretical article, we introduce the Differential Susceptibility to Media Effects Model (DSMM), a new, integrative model to improve our understanding of media effects. The DSMM organizes, integrates, and extends the insights developed in earlier microlevel media-effects theories. It

Energy landscape, structure and rate effects on strength properties of alpha-helical proteins

International Nuclear Information System (INIS)

Bertaud, Jeremie; Hester, Joshua; Jimenez, Daniel D; Buehler, Markus J

2010-01-01

The strength of protein domains is crucial to identify the mechanical role of protein domains in biological processes such as mechanotransduction, tissue mechanics and tissue remodeling. Whereas the concept of strength has been widely investigated for engineered materials, the strength of fundamental protein material building blocks and how it depends on structural parameters such as the chemical bonding, the protein filament length and the timescale of observation or deformation velocity remains poorly understood. Here we report a systematic analysis of the influence of key parameters that define the energy landscape of the strength properties of alpha-helical protein domains, including energy barriers, unfolding and refolding distances, the locations of folded and unfolded states, as well as variations of the length and pulling velocity of alpha-helical protein filaments. The analysis is facilitated by the development of a double-well mesoscale potential formulation, utilized here to carry out a systematic numerical analysis of the behavior of alpha-helices. We compare the results against widely used protein strength models based on the Bell model, one of the simplest models used to characterize the strength of protein filaments. We find that, whereas Bell-type models are a reasonable approximation to describe the rupture of alpha-helical protein domains for a certain range of pulling speeds and values of energy barriers, the model ceases to hold for very large energy barriers and for very small pulling speeds, in agreement with earlier findings. We conclude with an application of our mesoscale model to investigate the effect of the length of alpha-helices on their mechanical strength. We find a weakening effect as the length of alpha-helical proteins increases, followed by an asymptotic regime in which the strength remains constant. We compare strand lengths found in biological proteins with the scaling law of strength versus alpha-helix filament length. The

Effect of cellulase treatment of long fiber fraction on strength ...

African Journals Online (AJOL)

fiber and unbeaten short-fiber fractions. The obtained test results have indicate that the application of enzyme on appropriate fiber fraction have positive effects on the strength properties of the corrugated medium. The short span compression ...

Strength training and testosterone treatment have opposing effects on migration inhibitor factor levels in ageing men

DEFF Research Database (Denmark)

Glintborg, D.; Christensen, L. L.; Kvorning, T.

2013-01-01

Strength Training and Testosterone Treatment Have Opposing Effects on Migration Inhibitor Factor Levels in Ageing Men......Strength Training and Testosterone Treatment Have Opposing Effects on Migration Inhibitor Factor Levels in Ageing Men...

Effect of River Indus Sand on Concrete Tensile Strength

Directory of Open Access Journals (Sweden)

M. T. Lakhiar

2018-04-01

Full Text Available In the development of Pakistan construction industry, the utilization of River Indus sand in concrete as fine aggregate has expanded tremendously. The aim of this research is to study the effect of Indus River sand on the tensile strength of various grades of concrete when it is utilized as fine aggregate. Concrete Samples of M15, M20 and M25 grade concrete were cured for 7, 14, 21 and 28 days. Based on the results, it is found that concrete became less workable when Indus river sand was utilized. It is recorded that tensile strength of concrete is decreased from 5% up to 20% in comparison with hill sand. The results were derived from various concrete grades.

Ionic Strength Differentially Affects the Bioavailability of Neutral and Negatively Charged Inorganic Hg Complexes.

Science.gov (United States)

Stenzler, Benjamin; Hinz, Aaron; Ruuskanen, Matti; Poulain, Alexandre J

2017-09-05

Mercury (Hg) bioavailability to bacteria in marine systems is the first step toward its bioamplification in food webs. These systems exhibit high salinity and ionic strength that will both alter Hg speciation and properties of the bacteria cell walls. The role of Hg speciation on Hg bioavailability in marine systems has not been teased apart from that of ionic strength on cell wall properties, however. We developed and optimized a whole-cell Hg bioreporter capable of functioning under aerobic and anaerobic conditions and exhibiting no physiological limitations of signal production to changes in ionic strength. We show that ionic strength controls the bioavailability of Hg species, regardless of their charge, possibly by altering properties of the bacterial cell wall. The unexpected anaerobic bioavailability of negatively charged halocomplexes may help explain Hg methylation in marine systems such as the oxygen-deficient zone in the oceanic water column, sea ice or polar snow.

Immediate effects of kinesiotaping on quadriceps muscle strength: a single-blind, placebo-controlled crossover trial.

Science.gov (United States)

Vercelli, Stefano; Sartorio, Francesco; Foti, Calogero; Colletto, Lorenzo; Virton, Domenico; Ronconi, Gianpaolo; Ferriero, Giorgio

2012-07-01

To investigate the immediate effects on maximal muscle strength of kinesiotaping (KT) applied to the dominant quadriceps of healthy subjects. Single-blind, placebo-controlled crossover trial. "Salvatore Maugeri" Foundation. With ethical approval and informed consent, a convenience sample of 36 healthy volunteers were recruited. Two subjects did not complete the sessions and were excluded from the analysis. Subjects were tested across 3 different sessions, randomly receiving 2 experimental KT conditions applied with the aim of enhancing and inhibiting muscle strength and a sham KT application. Quadriceps muscle strength was measured by means of an isokinetic maximal test performed at 60 and 180 degrees per second. Two secondary outcome measures were performed: the single-leg triple hop for distance to measure limb performance and the Global Rating of Change Scale (GRCS) to calculate agreement between KT application and subjective perception of strength. Compared with baseline, none of the 3 taping conditions showed a significant change in muscle strength and performance (all P > 0.05). Effect size was very low under all conditions (≤0.08). Very few subjects showed an individual change greater than the minimal detectable change. Global Rating of Change Scale scores demonstrated low to moderate agreement with the type of KT applied, but some placebo effects were reported independently of condition. Our findings indicated no significant effect in the maximal quadriceps strength immediately after the application of inhibition, facilitation, or sham KT. These results do not support the use of KT applied in this way to change maximal muscle strength in healthy people.

Effect of magnetic water on strength and workability of high performance concrete

Directory of Open Access Journals (Sweden)

Moosa Mazloom

2016-09-01

Full Text Available Nowadays, concrete is one of the most important and widely used human product. Improving concrete characteristics have always been one of the fundamental subjects for engineers. Improve the physical properties of water, as one of the main elements of concrete, is one way to improve the characteristics of the concrete. When water passes through the magnetic field, its physical quality has changed, it is called Magnetic water. This study examines the effect of the use of magnetized water (MW with a solenoid current-carrying, on the compressive strength and workability of high performance concrete. The variables of this study were the intensity of magnetic field, the silica fume replacement level and water to cement ratio in different mixes. The results show that using MW increases the workability of concrete about 36% in average.MW in combination with superplasticizer is more effective than MW on workability and compressive strength of concrete. MW had more positive effects on the samples without silica fume. Increasing the intensity of magnetic field improved the workability, 28 and 90 days compressive strength concrete.

Garnet Yield Strength at High Pressures and Implications for Upper Mantle and Transition Zone Rheology

International Nuclear Information System (INIS)

Kavner, A.

2008-01-01

Garnet helps control the mechanical behavior of the Earth's crust, mantle, and transition zone. Here, measurements are presented suggesting that garnet, long considered to be a high-viscosity phase, is actually weaker than the other dominant components in the transition zone. The mechanical behavior of garnet at high pressures was examined using radial diffraction techniques in the diamond anvil cell. The yield strength of grossular garnet was inferred from synchrotron X-ray measurements of differential lattice strains. The differential stress was found to increase from 1.3 (±0.6) GPa at a hydrostatic pressure 5.8 (±1.1) GPa to 4.1 (±0.4) GPa at 15.7 (±1.0) GPa, where it was level to 19 GPa. The strength results are consistent with inferred strength values for majorite garnet from measurements in the diamond cell normal geometry, bolstering the idea that garnet-structured materials may all have similar strengths. In this low-temperature, high differential stress regime, garnet is shown to be significantly weaker than anhydrous ringwoodite and to have a strength similar to hydrous ringwoodite. This result suggests that the presence of water in the transition zone may not be required to explain a weak rheology, and therefore models of transition zone behavior built assuming that garnet is the high-strength phase may need to be revised.

Accounting sodium effect in calculation of strength of nuclear reactor components

International Nuclear Information System (INIS)

Nikitin, V.I.

1981-01-01

Accounting methods of liquid sodium effect on long-term strength and creep of structural materials of nuclear reactors are considered. The decrease of pearlite steel strength at the decarburization expense and the decrease of plasticity of austenitic steels at the expense of carburization are noted. The necessity to account thermal transfer of mass is shown. Values of safety factors are presented, they are recommended for the design of reactor component parts with the thickness not less than 1 mm [ru

Differential Effects of Heavy Versus Moderate Loads on Measures of Strength and Hypertrophy in Resistance-Trained Men

OpenAIRE

Brad J. Schoenfeld, Bret Contreras, Andrew D. Vigotsky, Mark Peterson

2016-01-01

The purpose of the present study was to evaluate muscular adaptations between heavy- and moderate-load resistance training (RT) with all other variables controlled between conditions. Nineteen resistance-trained men were randomly assigned to either a strength-type RT routine (HEAVY) that trained in a loading range of 2-4 repetitions per set (n = 10) or a hypertrophy-type RT routine (MODERATE) that trained in a loading range of 8-12 repetitions per set (n = 9). Training was carried out 3 days ...

The effect of increasing strength and approach velocity on triple jump performance.

Science.gov (United States)

Allen, Sam J; Yeadon, M R Fred; King, Mark A

2016-12-08

The triple jump is an athletic event comprising three phases in which the optimal phase ratio (the proportion of each phase to the total distance jumped) is unknown. This study used a planar whole body torque-driven computer simulation model of the ground contact parts of all three phases of the triple jump to investigate the effect of strength and approach velocity on optimal performance. The strength and approach velocity of the simulation model were each increased by up to 30% in 10% increments from baseline data collected from a national standard triple jumper. Increasing strength always resulted in an increased overall jump distance. Increasing approach velocity also typically resulted in an increased overall jump distance but there was a point past which increasing approach velocity without increasing strength did not lead to an increase in overall jump distance. Increasing both strength and approach velocity by 10%, 20%, and 30% led to roughly equivalent increases in overall jump distances. Distances ranged from 14.05m with baseline strength and approach velocity, up to 18.49m with 30% increases in both. Optimal phase ratios were either hop-dominated or balanced, and typically became more balanced when the strength of the model was increased by a greater percentage than its approach velocity. The range of triple jump distances that resulted from the optimisation process suggests that strength and approach velocity are of great importance for triple jump performance. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effect of Preparation Methods on Crystallization Behavior and Tensile Strength of Poly(vinylidene fluoride) Membranes.

Science.gov (United States)

Liu, Jie; Lu, Xiaolong; Wu, Chunrui

2013-11-21

Poly(vinylidene fluoride) (PVDF) membranes were prepared by non solvent induced phase separation (NIPS), melt spinning and the solution-cast method. The effect of preparation methods with different membrane formation mechanisms on crystallization behavior and tensile strength of PVDF membranes was investigated. Fourier transform infrared spectroscopy-attenuated total reflectance (FTIR-ATR) and X-ray diffraction (XRD) were employed to examine the crystal form of the surface layers and the overall membranes, respectively. Spherulite morphologies and thermal behavior of the membranes were studied by polarized light optical microscopy (PLO) and differential scanning calorimetry (DSC) separately. It was found that the crystallization behavior of PVDF membranes was closely related to the preparation methods. For membranes prepared by the NIPS method, the skin layers had a mixture of α and β phases, the overall membranes were predominantly α phase, and the total crystallinity was 60.0% with no spherulite. For melt spinning membranes, the surface layers also showed a mixture of α and β phases, the overall membranes were predominantly α phase. The total crystallinity was 48.7% with perfect spherulites. Whereas the crystallization behavior of solution-cast membranes was related to the evaporation temperature and the additive, when the evaporation temperature was 140 °C with a soluble additive in the dope solution, obvious spherulites appeared. The crystalline morphology of PVDF exerted a great influence on the tensile strength of the membranes, which was much higher with perfect spherulites.

Stepfamily Communication Strengths: Understanding the Ties That Bind.

Science.gov (United States)

Golish, Tamara D.

2003-01-01

Examines the communication strategies that differentiate "strong" stepfamilies from stepfamilies having more difficulty, inductively deriving a composite of stepfamily "communication strengths." Finds that in general, strong stepfamilies reported using everyday talk, more openness, spending time together as a family, communicating clear rules and…

Effect of deep stripping massage alone or with eccentric resistance on hamstring length and strength.

Science.gov (United States)

Forman, Jeffrey; Geertsen, Lisbeth; Rogers, Michael E

2014-01-01

Many studies have evaluated the effects of different interventions on hamstring length. However, little research has been conducted on the effects of deep stripping massage strokes (DSMS) alone, or combined with eccentric resistance, on hamstring length and strength. To determine: 1) if DSMS have an effect on hamstring length and strength and 2) if the effects on hamstring length and strength are any different when DSMS are combined with eccentric exercise. 89 Community College students and community members between the ages of 18 and 62 volunteered for the study. Of these, 64 demonstrated tight hamstrings on either one or both sides as defined by supine, passive terminal knee extension of ≤75° and participated in the study. Strength was assessed by pressing the posterior calcaneus into a strain gauge for approximately 5 s while seated with the knee flexed to 90°. On their tighter side, participants were administered longitudinal DSMS during 15, 10-s bouts of eccentric resistance with an elastic resistance band. On their other hamstring, participants were administered 15, 10-s longitudinal DSMS while lying passive. All massage strokes were performed at a depth of 7 out of 10 on a verbal pressure scale index. Afterwards, the hamstring flexibility and strength tests were repeated. Both DSMS with eccentric resistance (10.7%) and DSMS alone (6.3%) resulted in improved (p alone. Strength was not significantly affected by either treatment. These results suggest that DSMS increases hamstring length in less than 3 min but has no affect on strength. Furthermore, combining DSMS with eccentric resistance produces more hamstring flexibility gains than DSMS alone and does not affect strength. Copyright © 2013 Elsevier Ltd. All rights reserved.

Effect of Various Surface Treatment on Repair Strength of Composite Resin

Directory of Open Access Journals (Sweden)

Y. Alizade

2004-12-01

Full Text Available Statement of Problem: In some clinical situations, repair of composite restorations is treatment of choice. Improving the bond strength between one new and old composite usually requires increased surface roughness to promote mechanical interlocking sincechemical bonding might not be adequate. Similarly, the treatment of a laboratory fabricated resin composite restoration involves the same procedures, and there is a need to create the strongest possible bond of a resin cement to a previously polymerized composite.Purpose: The aim of this study was to evaluate the effect of various surface treatments on the shear bond strength of repaired to aged composite resin.Materials and Methods: Eighty four cylindrical specimens of a composite resin were fabricated and stored in distilled water for 100 days prior to surface treatment. Surface treatment of old composite was done in 6 groups as follow:1- Air abrasion with CoJet sand particles with micoretcher + silane + dentin bonding agent2- Air abrasion with 50μm Al2O3 particles+ phosphoric acid+ silane+ dentin bonding agent3- Air abrasion with 50μm Al2O3 particles + phosphoric acid + dentin bonding agent4- Diamond bur + phosphoric acid + silane + dentin bonding agent5- Diamond bur + phosphoric acid + dentin bonding agent6- Diamond bur + phosphoric acid + composite activator + dentin bonding agentThen fresh composite resin was bonded to treated surfaces. Twelve specimens were also fabricated as control group with the same diameter but with the height twice as much as other specimens. All of the specimens were thermocycled prior to testing for shear bondstrength. The bond strength data were analyzed statistically using one way ANOVA test, t test and Duncan's grouping test.Results: One-way ANOVA indicated no significant difference between 7 groups (P=0.059. One-way ANOVA indicated significant difference between the three diamond bur groups (P=0.036. Silane had a significant effect on the repair bond

Effect of High-Speed Strength Training on Physical Performance in Young Soccer Players of Different Ages.

Science.gov (United States)

Rodríguez-Rosell, David; Franco-Márquez, Felipe; Mora-Custodio, Ricardo; González-Badillo, Juan José

2017-09-01

Rodríguez-Rosell, D, Franco-Márquez, F, Mora-Custodio, R, and González-Badillo, JJ. Effect of high-speed strength training on physical performance in young soccer players of different ages. J Strength Cond Res 31(9): 2498-2508, 2017-The aim of the present study was to compare the effectiveness of low-load, low-volume weight training combined with plyometrics on strength, sprint, and jump performance in soccer players of different ages. Eighty-six soccer players from the same academy were categorized into 3 groups by age (under 13 years, U13, n = 30; under 15, U15, n = 28; and under 17, U17, n = 28) and then randomly assigned into 2 subgroups: a strength training group (STG) and a control group (CG). The strength training program was performed twice a week for 6 weeks and consisted of full squats (load: 45-60% 1 repetition maximum; volume: 3 set of 8-4 repetitions), jumps, and straight line sprint exercises. After training intervention, the STGs showed significant improvements in maximal strength (7.5-54.5%; p soccer players in most variables, whereas U15 showed higher improvements in jump and strength parameters than U17 (ES: 0.25-0.90) soccer players. Thus, although our results indicates that a combined weight training and plyometrics program may be effective in eliciting gains in strength, jump, and sprint in soccer players of different ages, the training program used appears to be generally less effective as the age of the soccer players increased. Therefore, it appears that training characteristics (mainly volume, intensity, and type of exercise) should be modified in relation to maturity status and initial strength level.

Effects of walking and strength training on walking capacity in individuals with claudication: meta-analysis

Directory of Open Access Journals (Sweden)

Alessandra de Souza Miranda

2013-06-01

Full Text Available CONTEXT: Over the past few years, several clinical trials have been performed to analyze the effects of exercise training on walking ability in patients with intermittent claudication (IC. However, it remains unclear which type of physical exercise provides the maximum benefits in terms of walking ability. OBJECTIVE: To analyze, by means of a meta-analysis, the effects of walking and strength training on the walking capacity in patients with IC. METHODS: Papers analyzing the effects of walking and strength training programs in patients with IC were browsed on the Medline, Lilacs, and Cochrane databases. Randomized clinical trials scoring >4 on the Physiotherapy Evidence Database (PEDro scale and assessing claudication distance (CD and total walking distance (TWD were included in the review. RESULTS: Walking and strength training yielded increases in CD and TWD (P < 0.05. However, walking training yielded greater increases than strength training (P = 0.02. CONCLUSION: Walking and strength training improve walking capacity in patients with IC. However, greater improvements in TWD are obtained with walking training.

The Importance of Muscular Strength: Training Considerations.

Science.gov (United States)

Suchomel, Timothy J; Nimphius, Sophia; Bellon, Christopher R; Stone, Michael H

2018-04-01

This review covers underlying physiological characteristics and training considerations that may affect muscular strength including improving maximal force expression and time-limited force expression. Strength is underpinned by a combination of morphological and neural factors including muscle cross-sectional area and architecture, musculotendinous stiffness, motor unit recruitment, rate coding, motor unit synchronization, and neuromuscular inhibition. Although single- and multi-targeted block periodization models may produce the greatest strength-power benefits, concepts within each model must be considered within the limitations of the sport, athletes, and schedules. Bilateral training, eccentric training and accentuated eccentric loading, and variable resistance training may produce the greatest comprehensive strength adaptations. Bodyweight exercise, isolation exercises, plyometric exercise, unilateral exercise, and kettlebell training may be limited in their potential to improve maximal strength but are still relevant to strength development by challenging time-limited force expression and differentially challenging motor demands. Training to failure may not be necessary to improve maximum muscular strength and is likely not necessary for maximum gains in strength. Indeed, programming that combines heavy and light loads may improve strength and underpin other strength-power characteristics. Multiple sets appear to produce superior training benefits compared to single sets; however, an athlete's training status and the dose-response relationship must be considered. While 2- to 5-min interset rest intervals may produce the greatest strength-power benefits, rest interval length may vary based an athlete's training age, fiber type, and genetics. Weaker athletes should focus on developing strength before emphasizing power-type training. Stronger athletes may begin to emphasize power-type training while maintaining/improving their strength. Future research should

Gamow-Teller strength in the continuum studied via the (p,n) reaction

International Nuclear Information System (INIS)

Wakasa, T.; Hatanaka, K.; Sakai, H.

2002-01-01

The double differential cross sections for θ lab between 0.0deg and 14.7deg and the polarization transfer coefficient D NN (0deg) for the 27 Al (p vector, n vector) reaction have been measured at a bombarding energy of 295 MeV. A multipole decomposition technique is applied for the cross section data to extract L=0, 1, 2, and 3 contributions. The Gamow-Teller (GT) strength B(GT) deduced from the L=0 contribution is compared with the B(GT) values calculated in a full sd shell-model space. The sum of B(GT) values up to 20 MeV excitation is S β- =4.0 ± 0.1 ± 0.1. A fairly large L=0 contribution is observed in the continuum region up to 50 MeV, which could be in part ascribed to the quenched GT strength. A limit on the effect that the Δ(1232)-isobar nucleon-hole admixture has upon the GT strength is estimated. (author)

Effects of interface roughness on cohesive strength of self-assembled monolayers

Energy Technology Data Exchange (ETDEWEB)

Zhang, Chen [Department of Aerospace Engineering, University of Illinois at Urbana-Champaign, IL 61801 (United States); Awasthi, Amnaya P. [Department of Mechanical and Aerospace Engineering, University of Florida, Gainesville, 32611 (United States); Geubelle, Philippe H., E-mail: geubelle@illinois.edu [Department of Aerospace Engineering, University of Illinois at Urbana-Champaign, IL 61801 (United States); Grady, Martha E.; Sottos, Nancy R. [Department of Materials Science and Engineering, University of Illinois at Urbana-Champaign, IL 61801 (United States)

2017-03-01

Highlights: • Self-assembled monolayer/transfer-printed gold interface modeled using continuum-level simulation. • Initial deformed film profile analyzed and instability assessed. • Effective cohesive response of SAM-enhanced interface extracted from spallation model. • Reduction of up to 70% cohesive strength of the interface from incorporation of roughness demonstrated. - Abstract: Self-assembled monolayers (SAMs) are aggregates of small molecular chains that have the property to form highly ordered assemblies. The choice of terminal groups on the chains makes them excellent contenders of molecular-level tailoring. Molecular dynamics (MD) simulations and experimental observations of spallation of two SAM-enhanced gold-film/silicon-substrate interfaces have shown that the cohesive strength of SAM-enriched transfer-printed interfaces is strongly dependent on the choice of terminal groups. Though the MD results of perfectly ordered atomistic surfaces show the same qualitative trend as the experiments, they over-predict the interfacial cohesive strengths by a factor of about 50. Results from AFM studies have revealed that the roughness of these interfaces is of the same order (∼1 nm) as the range of atomistic interactions. Hence, surface roughness is a key contributor in significantly reducing interfacial cohesive strength in these systems. In this manuscript, a continuum-level study is performed to investigate the influence of surface roughness on the cohesive strength of the interface between a Si/SAM substrate and a transfer-printed gold film. We approximate the film as a deformable continuum interacting with a rough substrate of SAMs represented by a harmonic function. Using a cohesive law derived from MD, spallation is simulated to evaluate the effective traction-separation characteristics for the rough SAM–gold interface. Our analysis shows that incorporating roughness may reduce the interfacial cohesive strength by an order of magnitude depending

Effect of whole-body vibration on muscle strength, spasticity, and ...

African Journals Online (AJOL)

CP) and is characterized by spasticity and muscle weakness of both lower limbs resulting in decreased walking ability. The purpose of this study was to evaluate the effect of whole body vibration (WBV) training on muscle strength, spasticity, and ...

Effects of Elevated Temperature on Compressive Strength Of Concrete

African Journals Online (AJOL)

This study presents the results of investigation of the effects of elevated temperatures on the compressive strength of Grade 40 concrete. A total of thirty cube specimens were cast, cured in water at ambient temperature in the laboratory and subjected to various temperature regimes before testing. A concrete mix of 1:1:3 ...

Boron effects on creep rupture strength of W containing advanced ferritic creep resistant steels

Energy Technology Data Exchange (ETDEWEB)

Mito, N.; Hasegawa, Y. [Tohoku Univ., Sendai (Japan)

2010-07-01

The creep strength in ferritic creep resistant steels is increased by boron addition. However, the strengthening mechanisms have not yet been studied. This study clarifies the strengthening mechanism of 9% chromium steels with 10{proportional_to}100ppm boron and 0.5{proportional_to}2.0mass% tungsten in the laboratory. The strengthening effect of simultaneous addition of boron and tungsten was analyzed by hardenability, room-temperature strength and creep tests at 650 C. Changes in the microstructure as a result of the addition of boron and tungsten were also examined by optical microscope and transmission electron microscope (TEM). In addition, Alpha-ray Track Etching (ATE) method was used to detect the boron distribution and analyze the mechanisms change in the mechanical properties. Boron addition did not affect room-temperature strength, however, simultaneous addition of boron and tungsten increased room-temperature and high-temperature strength. According to ATE analysis, boron exists at the grain boundary. Therefore, synergistic effects of boron and tungsten on the creep strength suggest the tungsten precipitates stabilization by boron at the grain boundary. (orig.)

Effect of Positive Psychotherapy in Depression Symptoms and Character Strengths in Cancer Affected Patients

Directory of Open Access Journals (Sweden)

R Khodabakhash

2015-05-01

Full Text Available The purpose of this research was to study the effect of positive psychotherapy on depression symptoms and character strengths in cancer affected patients. Based on a quasi-experimental design by available sampling, 58 cancer patients were investigated. 30 patients were assigned in two groups: 15 patients in positive psychotherapy group (treatment and 15 patients as control group. In the present research, Oxford Happiness-Depression Questionnaire (OHDQ and Values In Action Inventory of Strengths (VIA-IS were used. The results showed that the positive psychotherapy was effective in reducing depression, increasing the character strengths and virtues, improving meaningful, pleasant and engaged life of cancer patients.

Effect of newer antioxidants on the bond strength of composite on bleached enamel

Directory of Open Access Journals (Sweden)

M Manoharan

2016-01-01

Full Text Available Aim: The study aims to evaluate the effect of the application of two antioxidants on the bond strength of composite resin to bleached enamel. Materials and Methods: Eighty enamel surfaces were obtained from forty human extracted premolars. Specimens were randomly divided into four groups (n = 20. Group 1: No bleaching (control; Group 2a: Bleaching with 15% carbamide peroxide gel; Group 2b: Bleaching, followed by application of 10% sodium ascorbate gel; Group 2c: Bleaching, followed by application of 5% proanthocyanidin agent. Surfaces were etched followed by application of total etch bonding system, and composite resin cylinders were bonded. Specimens were tested for shear bond strength. Statistical Analysis Used: One-way analysis of variance was used for multiple group comparison and post hoc Tukey′s test for individual group-wise comparison. Results: Significantly higher shear bond strength values were observed in Group 2c and 2b as compared with Group 1 and 2a (P < 0.05. Among the antioxidants, Group 2c showed significantly higher shear bond strength values than Group 2b (P < 0.05. Conclusion: It can be concluded that the use of antioxidant before bonding procedures on bleached enamel completely neutralizes the deleterious effects of bleaching and increases the bond strength significantly.

Effect of Curing Temperature Histories on the Compressive Strength Development of High-Strength Concrete

Directory of Open Access Journals (Sweden)

Keun-Hyeok Yang

2015-01-01

Full Text Available This study examined the relative strength-maturity relationship of high-strength concrete (HSC specifically developed for nuclear facility structures while considering the economic efficiency and durability of the concrete. Two types of mixture proportions with water-to-binder ratios of 0.4 and 0.28 were tested under different temperature histories including (1 isothermal curing conditions of 5°C, 20°C, and 40°C and (2 terraced temperature histories of 20°C for an initial age of individual 1, 3, or 7 days and a constant temperature of 5°C for the subsequent ages. On the basis of the test results, the traditional maturity function of an equivalent age was modified to consider the offset maturity and the insignificance of subsequent curing temperature after an age of 3 days on later strength of concrete. To determine the key parameters in the maturity function, the setting behavior, apparent activation energy, and rate constant of the prepared mixtures were also measured. This study reveals that the compressive strength development of HSC cured at the reference temperature for an early age of 3 days is insignificantly affected by the subsequent curing temperature histories. The proposed maturity approach with the modified equivalent age accurately predicts the strength development of HSC.

Effects of surface treatment on bond strength between dental resin agent and zirconia ceramic

Energy Technology Data Exchange (ETDEWEB)

Moradabadi, Ashkan [Department of Electrochemistry, Universität Ulm, Ulm (Germany); Roudsari, Sareh Esmaeily Sabet [Department of Optoelectonics, Universität Ulm, Ulm (Germany); Yekta, Bijan Eftekhari [School of Materials Engineering, Iran University of Science and Technology, Tehran (Iran, Islamic Republic of); Rahbar, Nima, E-mail: nrahbar@wpi.edu [Department of Civil and Environmental Engineering, Worcester Polytechnic Institute, Worcester, MA 01609 (United States)

2014-01-01

This paper presents the results of an experimental study to understand the dominant mechanism in bond strength between dental resin agent and zirconia ceramic by investigating the effects of different surface treatments. Effects of two major mechanisms of chemical and micromechanical adhesion were evaluated on bond strength of zirconia to luting agent. Specimens of yttrium-oxide-partially-stabilized zirconia blocks were fabricated. Seven groups of specimens with different surface treatment were prepared. 1) zirconia specimens after airborne particle abrasion (SZ), 2) zirconia specimens after etching (ZH), 3) zirconia specimens after airborne particle abrasion and simultaneous etching (HSZ), 4) zirconia specimens coated with a layer of a Fluorapatite-Leucite glaze (GZ), 5) GZ specimens with additional acid etching (HGZ), 6) zirconia specimens coated with a layer of salt glaze (SGZ) and 7) SGZ specimens after etching with 2% HCl (HSGZ). Composite cylinders were bonded to airborne-particle-abraded surfaces of ZirkonZahn specimens with Panavia F2 resin luting agent. Failure modes were examined under 30 × magnification and the effect of surface treatments was analyzed by scanning electron microscopy (SEM) and atomic force microscopy (AFM). SZ and HSZ groups had the highest and GZ and SGZ groups had the lowest mean shear bond strengths among all groups. Mean shear bond strengths were significantly decreased by applying a glaze layer on zirconia surfaces in GZ and SGZ groups. However, bond strengths were improved after etching process. Airborne particle abrasion resulted in higher shear bond strengths compared to etching treatment. Modes of failure varied among different groups. Finally, it is concluded that micromechanical adhesion was a more effective mechanism than chemical adhesion and airborne particle abrasion significantly increased mean shear bond strengths compared with another surface treatments. - Highlights: • Understanding the dominant mechanism of bonding

A Systematic Review of the Effect of Cognitive Strategies on Strength Performance.

Science.gov (United States)

Tod, David; Edwards, Christian; McGuigan, Mike; Lovell, Geoff

2015-11-01

Researchers have tested the beliefs of sportspeople and sports medicine specialists that cognitive strategies influence strength performance. Few investigators have synthesised the literature. The specific objectives were to review evidence regarding (a) the cognitive strategy-strength performance relationship; (b) participant skill level as a moderator; and (c) cognitive, motivational, biomechanical/physiological, and emotional mediators. Studies were sourced via electronic databases, reference lists of retrieved articles, and manual searches of relevant journals. Studies had to be randomised or counterbalanced experiments with a control group or condition, repeated measures, and a quality control score above 0.5 (out of 1). Cognitive strategies included goal setting, imagery, self-talk, preparatory arousal, and free choice. Dependent variables included maximal strength, local muscular endurance, or muscular power. Globally, cognitive strategies were reliability associated with increased strength performance (results ranged from 61 to 65 %). Results were mixed when examining the effects of specific strategies on particular dependent variables, although no intervention had an overall negative influence. Indeterminate relationships emerged regarding hypothesised mediators (except cognitive variables) and participant skill level as a moderator. Although cognitive strategies influence strength performance, there are knowledge gaps regarding specific types of strength, especially muscular power. Cognitive variables, such as concentration, show promise as possible mediators.

Effect of ultraviolet light irradiation and sandblasting treatment on bond strengths between polyamide and chemical-cured resin.

Science.gov (United States)

Asakawa, Yuya; Takahashi, Hidekazu; Iwasaki, Naohiko; Kobayashi, Masahiro

2014-01-01

The aim of this study was to evaluate the effects of ultraviolet light (UV) irradiation and sandblasting treatment on the shear bond strength between polyamide and chemical-cured resin. Three types of commercial polyamides were treated using UV irradiation, sandblasting treatment, and a combining sandblasting and UV irradiation. The shear bond strength was measured and analyzed using the Kruskal-Wallis test (α=0.05). Comparing shear bond strengths without surface treatment, from 4.1 to 5.7 MPa, the UV irradiation significantly increased the shear bond strengths except for Valplast, whose shear bond strengths ranged from 5.2 to 9.3 MPa. The sandblasting treatment also significantly increased the shear bond strengths (8.0 to 11.4 MPa). The combining sandblasting and UV irradiation significantly increased the shear bond strengths (15.2 to 18.3 MPa) comparing without surface treatment. This combined treatment was considered the most effective at improving the shear bond strength between polyamide and chemical-cured resin.

Combined effects of petrographic and technological parameters on strength of porous coke substance

Energy Technology Data Exchange (ETDEWEB)

Dinel' t, V.M.; Shkoller, M.B.; Stankevich, A.S.; Korchuganova, G.S.

1983-01-01

A laboratory study was undertaken to study the combined effects of the basic petrographic characteristics of Kuzbas coal blends and the technological carbonization parameters on the structural strength of the porous coke. Strength tests were carried out on the original coke and the products of partial gasification with carbon dioxide under conditions simulating those inside blast furnaces. Properties of the 14 samples of Kuzbas coals and composition of the four coal blends made from them are listed. It was concluded that the structural strength of coke was most strongly influenced by the average reflectance index and bulk density of the charge. Also, charge compaction can largely offset the adverse influence of petrographic heterogeneity on the strength of the coke. 10 references, 3 tables.

EFFECTIVENESS OF SWISS BALL VS FLOOR EXERCISES ON CORE MUSCLE STRENGTH IN ELITE CRICKETERS

Directory of Open Access Journals (Sweden)

K. Sai sudha

2015-10-01

Full Text Available Background: Cricket is one of the most popular game in India played by men and women of all ages. The increased physical demands on the players may be associated with an increased risk of injuries. Core muscle strength is important to prevent risk of injuries in elite cricketers. The beginners in the cricket must have enough strength of core muscles, as core is the bridge between upper and lower limbs. So, it should be strong enough to prevent low back and lower limb injuries in cricketers. The aim is to determine the effectiveness of swiss ball exercises versus floor exercises on core muscle strength in elite cricketers. The objective is to study and compare the effectiveness of swiss ball exercises and floor exercises in elite cricketers in terms of back strength. Method: The total number of students in this study were 30 eilte cricketers between 16-25 years out of which 15 subjects were included each in floor exercise(n=15 and swiss ball group(n=15. Back strength was measured before and after the intervention of 6 weeks using isokinetic analyser. Results: After the analysis, the results revealed significant improvement of back strength in both the groups(p< 0.00. The swiss ball group showed significant results when compared with floor exercise group. Conclusion: Although the study showed beneficial results in both the groups, the results reflected that swiss ball group had better improvement of core muscle strength than the floor exercise group.

An Effect Size Measure for Raju's Differential Functioning for Items and Tests

Science.gov (United States)

Wright, Keith D.; Oshima, T. C.

2015-01-01

This study established an effect size measure for differential functioning for items and tests' noncompensatory differential item functioning (NCDIF). The Mantel-Haenszel parameter served as the benchmark for developing NCDIF's effect size measure for reporting moderate and large differential item functioning in test items. The effect size of…

Global model for the lithospheric strength and effective elastic thickness

NARCIS (Netherlands)

Tesauro, M.; Kaban, M.K.; Cloetingh, S.A.P.L.

2013-01-01

Global distribution of the strength and effective elastic thickness (Te) of the lithosphere are estimated using physical parameters from recent crustal and lithospheric models. For the Te estimation we apply a new approach, which provides a possibility to take into account variations of Young

Effect of mixing methods and aggregate type on strength of hardened concrete

International Nuclear Information System (INIS)

Elhadi, S.

2006-01-01

The objective of the research contained in this paper is to study the effect on strength of concrete which can be caused by changing method of concrete mix with or without changing aggregate crushing value under hand or mechanical compaction, and to compare results obtained when nondestructive testing techniques are used. It has been found that all methods of mix design are nearly identical in predicting the strength under a known value of w/c ratio. Up to strength of about 30 N/mm 2 , hand and mechanical compaction seems to be identical in all methods of concrete mixing. Important results regarding destructive and non-destructive testing has been drawn from the study.(Author)

Effect of Specimen Shape and Size on the Compressive Strength of Foamed Concrete

Directory of Open Access Journals (Sweden)

Sudin M.A.S.

2014-03-01

Full Text Available Lightweight concrete, in the form of foamed concrete, is a versatile material that primarily consists of a cement based mortar, mixed with at least 20% volume of air. Its dry density is typically below 1600 kg/m3 with a maximum compressive strength of 15MPa. The ASTM standard provision specifies a correction factor for concrete strength of between 14 and 42Mpa, in order to compensate for a reduced strength, when the aspect height-to-diameter ratio of a specimen is less than 2.0. However, the CEB-FIP provision specifically mentions a ratio of 150mm dia. × 300mm cylinder strength to 150 mm cube strength; though, both provision requirements do not specifically clarify the applicability and/or modification of the correction factors for the compressive strength to lightweight concrete (in this case, foamed concrete. The focus of this work is to study the effect of specimen size and shape on the axial compressive strength of concrete. Specimens of various sizes and shapes were cast with square and circular cross-sections i.e., cubes, prisms, and cylinders. Their compression strength behaviours at 7 and 28 days were investigated. The results indicate that, as the CEB-FIP provision specified, even for foamed concrete, 100mm cubes (l/d = 1.0 produce a comparable compressive strength with 100mm dia. × 200mm cylinders (l/d = 2.0.

Effects of Resistance Training on Muscle Strength, Endurance, and Motor Unit According to Ciliary Neurotrophic Factor Polymorphism in Male College Students

Directory of Open Access Journals (Sweden)

Ae-Rim Hong, Sang-Min Hong, Yun-A Shin

2014-09-01

Full Text Available Changes in muscle mass and strength across the adult age span are variable and related to the ciliary neurotrophic factor (CNTF genotype. In particular, a single CNTF haplotype (1357 G→A is important for neuronal and muscular developments and may be associated with muscle strength response to resistance training. We examined whether CNTF genotype differentially influences the effect of resistance training on neuromuscular improvement in male college students. Resistance training of the upper extremities comprised 3 sets at 75%–85% intensity per 1 repetition maximum, 3 times a week, for a total of 8 weeks. We measured isokinetic muscle function of the elbow joint with regard to strength (60°/s and endurance (180°/s by using an isokinetic dynamometer. The biceps brachii (BB and brachioradialis muscles were studied using surface electromyography with spike-triggered averaging to assess surface-detected motor unit potential (SMUP area. After resistance training, the SMUP of the BB increased significantly at 60°/s (p < 0.05, but no difference in the CNTF genotype was observed. The SMUP of the BB at 180°/s increased significantly in the GG/AA genotype group compared with that in the GA genotype group (p < 0.05. The average power of the elbow flexor at 180°/s increased significantly after resistance training (p < 0.05, but again, no difference in the CNTF genotype was observed. Thus, improvements in muscle strength and endurance may have resulted directly from resistance training rather than from genetic factors related to nerves in muscle tissue.

The Effects of Isokinetic Strength Training on Strength at Different Angular Velocities: a Pilot Study

Directory of Open Access Journals (Sweden)

Tuğba Kocahan

2017-09-01

Conclusion: It was shown that angular velocity is important in isokinetic training, and that training at high angular velocities provides strength increases at lower angular velocities, but would not increase strength at angular velocities above the training level. For this reason, it is thought that in the preparation of an isokinetic strength training protocol, angular velocities need to be taken into account. For any athlete, the force at the angular velocity required in her/his sports branch needs to be considered.

Effects of the network structure and coupling strength on the noise-induced response delay of a neuronal network

International Nuclear Information System (INIS)

Ozer, Mahmut; Uzuntarla, Muhammet

2008-01-01

The Hodgkin-Huxley (H-H) neuron model driven by stimuli just above threshold shows a noise-induced response delay with respect to time to the first spike for a certain range of noise strengths, an effect called 'noise delayed decay' (NDD). We study the response time of a network of coupled H-H neurons, and investigate how the NDD can be affected by the connection topology of the network and the coupling strength. We show that the NDD effect exists for weak and intermediate coupling strengths, whereas it disappears for strong coupling strength regardless of the connection topology. We also show that although the network structure has very little effect on the NDD for a weak coupling strength, the network structure plays a key role for an intermediate coupling strength by decreasing the NDD effect with the increasing number of random shortcuts, and thus provides an additional operating regime, that is absent in the regular network, in which the neurons may also exploit a spike time code

Effect of low transverse magnetic field on the confinement strength in a quasi-1D wire

International Nuclear Information System (INIS)

Kumar, Sanjeev; Thomas, K. J.; Smith, L. W.; Farrer, I.; Ritchie, D. A.; Jones, G. A. C.; Griffiths, J.; Pepper, M.

2013-01-01

Transport measurements in a quasi-one dimensional (1D) quantum wire are reported in the presence of low transverse magnetic field. Differential conductance shows weak quantised plateaus when the 2D electrons are squeezed electrostatically. Application of a small transverse magnetic field (0.2T) enhances the overall degree of quantisation due to the formation of magneto-electric subbands. The results show the role of magnetic field to fine tune the confinement strength in low density wires when interaction gives rise to double row formation

Effect of confinement on bond strength of hot-dip galvanized lap splices in concrete structures

International Nuclear Information System (INIS)

Fakhran, Mazen

2004-01-01

Galvanizing the reinforcing steel is one of the methods used to protect bars against corrosion. Galvanizing is a hot dip process where the reinforcing bars are immersed in an aqueous pre flux solution of zinc ammonium chloride at a controlled temperature between 840 and 850 degrees F. In 2001, a research program was started at AUB to evaluate experimentally the effect of hot dip galvanizing on the bond capacity of tension lap splices anchored in full-scale beam specimens designed to fail in bond splitting mode. The test results indicated that the use of galvanized bars had a negligible effect on bond strength of reinforcement in normal strength. However, galvanizing caused an average of 20 percent decrease in bond strength of reinforcement in high strength concrete. The primary objective of research reported in this thesis, is the need to find a solution to eliminate the bond reduction of galvanized bars in high strength concrete. It is significant to evaluate the positive effect of the addition of transverse reinforcement in the splice region. The hypothesis to be tested is that such transverse reinforcement will insure uniform bond stress distribution over the entire splice region, thus mobilizing all bar lugs along the splice in the stress transfer mechanism between the bar and the surrounding concrete. Such mechanism might reduce the significant decrease in bond strength in high strength concrete due to galvanizing. To achieve this objective, eighteen full-scale beam specimens were tested in positive bending. Each beam was reinforced with bars spliced in a constant moment region at midspam. The splice length was chosen in such a way that the beams failed in bond splitting of the concrete cover in the splice region. The main variables were type of coating (black or galvanized bars), bar size (20, 25 and 32 mm), and amount of transverse reinforcement in the splice region (0, 2 or 4 stirrups). The test results indicated that confinement did not have a significant

Neck/shoulder function in tension-type headache patients and the effect of strength training

DEFF Research Database (Denmark)

Madsen, Bjarne K; Søgaard, Karen; Andersen, Lars L.

2018-01-01

Introduction: Muscle pain has been associated with reduced maximal muscle strength, and reduced rate of force development (RFD). Strength training (ST) has shown an effect in not only normalizing muscle function but also reducing neck muscle pain. Aim: The aims of this study were to compare muscle...... function in terms of strength, force steadiness in neck flexion, as well as extension, and rate of RFD of the shoulder in tension-type headache (TTH) patients and healthy controls and to examine the correlation to tenderness. Furthermore, the aim of the study was to examine the effect of ST on neck...... steadiness (ST: p=0.011 and EP: pfunction, indicated by a lower force steadiness and RFD, compared to the healthy controls. The effect of ST was not larger than EP as both groups of TTH patients showed some improvement in neck and shoulder...

Effects of core instability strength training on trunk muscle strength, spinal mobility, dynamic balance and functional mobility in older adults.

Science.gov (United States)

Granacher, Urs; Lacroix, Andre; Muehlbauer, Thomas; Roettger, Katrin; Gollhofer, Albert

2013-01-01

Age-related postural misalignment, balance deficits and strength/power losses are associated with impaired functional mobility and an increased risk of falling in seniors. Core instability strength training (CIT) involves exercises that are challenging for both trunk muscles and postural control and may thus have the potential to induce benefits in trunk muscle strength, spinal mobility and balance performance. The objective was to investigate the effects of CIT on measures of trunk muscle strength, spinal mobility, dynamic balance and functional mobility in seniors. Thirty-two older adults were randomly assigned to an intervention group (INT; n = 16, aged 70.8 ± 4.1 years) that conducted a 9-week progressive CIT or to a control group (n = 16, aged 70.2 ± 4.5 years). Maximal isometric strength of the trunk flexors/extensors/lateral flexors (right, left)/rotators (right, left) as well as of spinal mobility in the sagittal and the coronal plane was measured before and after the intervention program. Dynamic balance (i.e. walking 10 m on an optoelectric walkway, the Functional Reach test) and functional mobility (Timed Up and Go test) were additionally tested. Program compliance was excellent with participants of the INT group completing 92% of the training sessions. Significant group × test interactions were found for the maximal isometric strength of the trunk flexors (34%, p training-related improvements were found for spinal mobility in the sagittal (11%, p velocity (9%, p velocity (31%, p training regimen could be used as an adjunct or even alternative to traditional balance and/or resistance training. Copyright © 2012 S. Karger AG, Basel.

Masked and unmasked priming effects as a function of semantic relatedness and associative strength.

Science.gov (United States)

Sánchez-Casas, Rosa; Ferré, Pilar; Demestre, Josep; García-Chico, Teófilo; García-Albea, José E

2012-11-01

The study presented in this paper aimed to investigate the pattern of semantic priming effects, under masked and unmasked conditions, in the lexical decision task, manipulating type of semantic relation and associative strength. Three different kinds of word relations were examined in two experiments: only-semantically related words [e.g., codo (elbow)-rodilla (knee)] and semantic/associative related words with strong [e.g., mesa (table)-silla (chair) and weak association strength [e.g., sapo (toad)-rana (frog)]. In Experiment 1 a masked priming procedure was used with a prime duration of 56 ms, and in Experiment 2, the prime was presented unmasked for 150 ms. The results showed that there were masked priming effects with strong associates, but no evidence of these effects was found with weak associates or only-semantic related word pairs. When the prime was presented unmasked, the three types of relations produced significant priming effects and they were not influenced by association strength.

The effects of pilates on balance, mobility and strength in patients with multiple sclerosis.

Science.gov (United States)

Guclu-Gunduz, Arzu; Citaker, Seyit; Irkec, Ceyla; Nazliel, Bijen; Batur-Caglayan, Hale Zeynep

2014-01-01

Although there are evidences as to Pilates developing dynamic balance, muscle strength and flexibility in healthy people, evidences related to its effects on Multiple Sclerosis patients are insufficient. The aims of this study were to investigate the effects of Pilates on balance, mobility, and strength in ambulatory patients with Multiple Sclerosis. Twenty six patients were divided into two groups as experimental (n = 18) and control (n = 8) groups for an 8-week treatment program. The experimental group underwent Pilates and the control group did abdominal breathing and active extremity exercises at home. Balance and mobility were measured with Berg Balance Scale and Timed up and go test, upper and lower muscle strength with hand-held dynamometer. Confidence in balance skills while performing daily activities was evaluated with Activities Specific Balance Confidence Scale. Improvements were observed in balance, mobility, and upper and lower extremity muscle strength in the Pilates group (p 0.05). Due to its structure which is made up of balance and strengthening exercises, Pilates training may develop balance, mobility and muscle strength of MS patients. For this reason, we think that, Pilates exercises which are appropriate for the disability level of the patient may be suggested.

Effect of Quaternary Ammonium Salt on Shear Bond Strength of Orthodontic Brackets to Enamel

Directory of Open Access Journals (Sweden)

Hannaneh Ghadirian

2017-10-01

Full Text Available Objectives: This study sought to assess the effect of quaternary ammonium salt (QAS on shear bond strength of orthodontic brackets to enamel.Materials and Methods: In this in vitro experimental study, 0, 10, 20 and 30% concentrations of QAS were added to Transbond XT primer. Brackets were bonded to 60 premolar teeth using the afore-mentioned adhesive mixtures, and the shear bond strength of the four groups (n=15 was measured using a universal testing machine. After debonding, the adhesive remnant index (ARI score was determined under a stereomicroscope. Data were analyzed using one-way ANOVA.Results: The mean and standard deviation of shear bond strength of the control and 10%, 20% and 30% groups were 23.54±6.31, 21.81±2.82, 20.83±8.35 and 22.91±5.66 MPa, respectively. No significant difference was noted in shear bond strength of the groups (P=0.83. Study groups were not different in terms of ARI scores (P=0.80.Conclusions: The results showed that addition of QAS to Transbond XT primer had no adverse effect on shear bond strength of orthodontic brackets.

Hand Grip Strength Vs. Sprint Effectiveness in Amputee Soccer Players.

Science.gov (United States)

Wieczorek, Marta; Wiliński, Wojciech; Struzik, Artur; Rokita, Andrzej

2015-11-22

Amputee soccer is one of the types of soccer designed for the disabled, especially those who have undergone amputations, as well as those with extremity dysfunction. The objective of the study was to find the relationship between hand grip strength and sprint time in amputee soccer players. Thirteen field amputee soccer players participated in the study. A SAEHAN hydraulic hand dynamometer manufactured by Jamar was used for hand grip strength measurements. The sprint running test was conducted over a distance of 30 m. The Fusion Smart Speed System was employed for running time measurements. No statistically significant relationships were found between hand grip strength of the left or right hand, and sprint times over 1, 5, 10, 15, 20, 25 and 30 m. Analysis of the running velocity curve of the subjects showed an interesting profile characterized by a 15 meter-long acceleration phase and a significant velocity increase over a distance of 20 - 25 m. The study suggests that there is no relationship between hand grip strength and sprint effectiveness in amputee soccer players. The specificity of locomotion with the use of elbow crutches among elite Polish amputee soccer players probably accounts for the profile of the sprint velocity curve. Extension of the acceleration phase in the sprint run and a velocity increase in the subsequent part of the run were observed.

Hand Grip Strength Vs. Sprint Effectiveness in Amputee Soccer Players

Directory of Open Access Journals (Sweden)

Wieczorek Marta

2015-12-01

Full Text Available Amputee soccer is one of the types of soccer designed for the disabled, especially those who have undergone amputations, as well as those with extremity dysfunction. The objective of the study was to find the relationship between hand grip strength and sprint time in amputee soccer players. Thirteen field amputee soccer players participated in the study. A SAEHAN hydraulic hand dynamometer manufactured by Jamar was used for hand grip strength measurements. The sprint running test was conducted over a distance of 30 m. The Fusion Smart Speed System was employed for running time measurements. No statistically significant relationships were found between hand grip strength of the left or right hand, and sprint times over 1, 5, 10, 15, 20, 25 and 30 m. Analysis of the running velocity curve of the subjects showed an interesting profile characterized by a 15 meter-long acceleration phase and a significant velocity increase over a distance of 20 – 25 m. The study suggests that there is no relationship between hand grip strength and sprint effectiveness in amputee soccer players. The specificity of locomotion with the use of elbow crutches among elite Polish amputee soccer players probably accounts for the profile of the sprint velocity curve. Extension of the acceleration phase in the sprint run and a velocity increase in the subsequent part of the run were observed.

Effect of osteogenesis imperfecta mutations in tropocollagen molecule on strength of biomimetic tropocollagen-hydroxyapatite nanocomposites

Science.gov (United States)

Dubey, Devendra K.; Tomar, Vikas

2010-01-01

Osteogenesis Imperfecta (OI) is a genetic disorder that affects cellular synthesis of Type-I collagen fibrils and causes extreme bone fragility. This study reports the effects of OI mutations in Tropocollagen (TC) molecules on strength of model Tropocollagen-Hydroxyapatite biomaterials with two different mineral [hydroxyapatite (HAP)] distributions using three dimensional atomistic simulations. Results show that the effect of TC mutations on the strength of TC-HAP biomaterials is insignificant. Instead, change in mineral distribution showed significant impact on the overall strength of TC-HAP biomaterials. Study suggests that TC mutations manifest themselves by changing the mineral distribution during hydroxyapatite growth and nucleation period.

Effects of humidity and interlayer cations on the frictional strength of montmorillonite

Science.gov (United States)

Tetsuka, Hiroshi; Katayama, Ikuo; Sakuma, Hiroshi; Tamura, Kenji

2018-04-01

We developed a humidity control system in a biaxial friction testing machine to investigate the effect of relative humidity and interlayer cations on the frictional strength of montmorillonite. We carried out the frictional experiments on Na- and Ca-montmorillonite under controlled relative humidities (ca. 10, 30, 50, 70, and 90%) and at a constant temperature (95 °C). Our experimental results show that frictional strengths of both Na- and Ca-montmorillonite decrease systematically with increasing relative humidity. The friction coefficients of Na-montmorillonite decrease from 0.33 (at relative humidity of 10%) to 0.06 (at relative humidity of 93%) and those of Ca-montmorillonite decrease from 0.22 (at relative humidity of 11%) to 0.04 (at relative humidity of 91%). Our results also show that the frictional strength of Na-montmorillonite is higher than that of Ca-montmorillonite at a given relative humidity. These results reveal that the frictional strength of montmorillonite is sensitive to hydration state and interlayer cation species, suggesting that the strength of faults containing these clay minerals depends on the physical and chemical environment.[Figure not available: see fulltext.

The Effect of Corrosive Environment on Geopolymer Concrete Tensile Strength

Directory of Open Access Journals (Sweden)

Bayuaji Ridho

2017-01-01

Full Text Available This study has the purpose to explore the potential of geopolymer concrete tensile strength in particular on the effects of corrosive environments. Geopolymer concrete, concrete technology used no OPC that has advantages, one of which is durability, especially for corrosive seawater environment. In addition, geopolymer concrete with polymerization mechanism does not require large energy consumption or an environmentally friendly concept. Geopolymer concrete in this study is using a type C fly ash from PT. International Power Mitsui Operation & Maintenence Indonesia (IPMOMI Paiton. The type of alkaline activator used NaOH (14 molar and Na2SiO3. Coarse and fine aggregate used are local aggregate. Geopolymer concrete molded test specimen with dimensions of (10 × 20 cm cylinder, further heating and without heating, then maintained at room temperature and seawater up to 28 days. Then to determine the mechanical properties, the tensile strength testing is done with reference. This result of study indicates the curing of geopolymer concrete at 60 ° C for 24 hours to raise the tensile strength of geopolymer concrete.

Electron-impact excitation of Fe II: Effective collision strengths for optically allowed fine-structure transitions

International Nuclear Information System (INIS)

Ramsbottom, C.A.

2009-01-01

In this paper, we present collision strengths and Maxwellian averaged effective collision strengths for the electron-impact excitation of Fe II. We consider specifically the optically allowed lines for transitions from the 3d 6 4s and 3d 7 even parity configuration states to the 3d 6 4p odd parity configuration levels. The parallel suite of Breit-Pauli codes are utilized to compute the collision cross-sections where relativistic effects are included explicitly in both the target and the scattering approximation. A total of 100 LS or 262-jj levels formed from the basis configurations 3d 6 4s, 3d 7 and 3d 6 4p were included in the wavefunction representation of the target, including all doublet, quartet and sextet terms. The Maxwellian averaged effective collision strengths are computed across a wide range of electron temperatures from 100 to 100,000 K, temperatures of importance in astrophysical and plasma applications. A detailed comparison is made with previous works and significant differences were found to occur for some of the transitions considered. We conclude that in order to obtain converged collision strengths and effective collision strengths for these allowed transitions it is necessary to include contributions from partial waves up to L = 50 explicitly in the calculation, and in addition, account for contributions from even higher partial waves through a 'top up' procedure.

The electric strength of high-voltage transformers insulation at effect of partial dischargers

International Nuclear Information System (INIS)

Khoshravan, E.; Zeraatparvar, A.; Gashimov, A.M.; Mehdizadeh, R.N.

2001-01-01

Full text : In paper the change of electric strength of high-voltage transformers insulation at the effect of partial discharges with space charge accumulation was investigated. It is revealed that the effect of partial discharges of insulation materials results the reduction of their pulsing electric strength which can restore the own initial value at releasing of saved charge the volume of a material under condition of absence the ineversible structural changes in it. Researches of high-voltage transformers insulation's non-failure operation conditions show, that at increasing of insulation work time in a strong electrical field the reduction of average breakdown voltages with simultaneous increasing of spread in discharge voltage values takes place. It authentically testifies to reduction of short-time discharge voltage of insulation materials during their electrical aging. As the basic reason of insulation electrical aging the partial discharges occurring in gas cavities inside insulation were considered. It is known that the space charges will be formed in insulation elements of high-voltage devices which effects in dielectrical property of these elements including the electric strength and the space charge formation can occur also at partial discharges in an alternating voltage while the service of high-voltage transformers. In the given work the experiments in revealing separate influence partial discharges in pulsing electric strength of insulation materials at presence and at absence inside them the space charge were spent

The Effect of Maximal Strength Training on Strength, Walking, and Balance in People with Multiple Sclerosis: A Pilot Study

Directory of Open Access Journals (Sweden)

Herb I. Karpatkin

2016-01-01

Full Text Available There is little literature examining the use of maximal strength training (MST in people with multiple sclerosis (pwMS. This pretest-posttest study examined the effects of a MST program on strength, walking, balance, and fatigue in a sample of pwMS. Seven pwMS (median EDSS 3.0, IQR 1.5 participated in a MST program twice weekly for eight weeks. Strength was assessed with 1-repetition maximum (1RM on each leg. Walking and balance were measured with the 6-Minute Walk Test (6MWT and Berg Balance Scale (BBS, respectively. Fatigue was measured during each week of the program with the Fatigue Severity Scale (FSS. The program was well tolerated, with an attendance rate of 96.4%. Participants had significant improvements in right leg 1RM (t6=-6.032, P=0.001, left leg 1RM (t(6=-5.388, P=0.002, 6MWT distance (t(6=-2.572,P=0.042, and BBS score (Z=-2.371, P=0.018 after the MST intervention. There was no significant change in FSS scores (F(1,3.312=2.411, P=0.092. Participants in the MST program experienced improved balance and walking without an increase in fatigue. This MST program may be utilized by rehabilitation clinicians to improve lower extremity strength, balance, and mobility in pwMS.

Effects of Aerobic, Strength or Combined Exercise on Perceived Appetite and Appetite-Related Hormones in Inactive Middle-Aged Men.

Science.gov (United States)

Larsen, Penelope S; Donges, Cheyne E; Guelfi, Kym J; Smith, Greg C; Adams, David R; Duffield, Rob

2017-10-01

Aerobic exercise (AE) and strength exercise (SE) are reported to induce discrete and specific appetite-related responses; however, the effect of combining AE and SE (i.e., combined exercise; CE) remains relatively unknown. Twelve inactive overweight men (age: 48 ± 5 y; BMI: 29.9 ± 1.9 kg∙m 2 ) completed four conditions in a random order: 1) nonexercise control (CON) (50 min seated rest); 2) AE (50 min cycling; 75% VO 2peak ); 3) SE (10 × 8 leg extensions; 75% 1RM); and 4) CE (50% SE + 50% AE). Perceived appetite, and appetiterelated peptides and metabolites were assessed before and up to 2 h postcondition (0P, 30P, 60P, 90P, 120P). Perceived appetite did not differ between trials (p appetite-related peptides and metabolites. Despite these differential exercise-induced hormone responses, exercise mode appears to have little effect on perceived appetite compared with a resting control in this population.

Effect of friction stir lap welding conditions on joint strength of aluminium alloy 6060

International Nuclear Information System (INIS)

Yazdanian, S; Chen, Z W

2009-01-01

Strength of lap joints made by friction stir welding (FSW) depends strongly on how material flows forming the weld nugget zone during FSW and also on how the joint is loaded during testing. Understanding of this processing-property relationship is currently inadequate. In this study, the effects of pin length, welding speed and rotation rate on weld strength using aluminium alloy 6060 were investigated. It has been found that the pin length needed to be slightly greater than the thickness of the sheet for an adequate joint to be established. However, further increase in pin length did not benefit the joint strength. The major factor affecting joint strength has been found to be the rotation speed. An increase in rotation speed resulted in lowering the joint strength. Various modes of fracture have been observed and these modes relate to the degree of hooking and softening. Explanation of how the speed values relate to heat input and material flow and then to the joint strength is given.

Evaluation and Study the Effect of Additives and Other Factors on Tensile Strength of Asphalt Paving Mixtures

Directory of Open Access Journals (Sweden)

Hanaa Khaleel A. Al-Baiti

2012-03-01

Full Text Available The resistance of asphaltic concrete to cracking is dependent upon its tensile strength and flexibility characteristics. Also the low tensile strength has recognized as a major contributor to other performance problems. The fatigue life of mixtures decreases exponentially with decreasing of tensile strength. This trend is justified by the loss in stiffness and thereby initiating cracks and stripping. The main objective of this research is intended to study the effect of different variables related with the used materials and the external conditions on the tensile strength and predict a model of indirect tensile strength in asphalt concrete paving materials under the local prevailing conditions and investigate the effect of percent of additives of (Polyestrene resins and Hydrated Lime to enhance the resistance ability of asphalt concrete mixture against distresses. The main affected factors; soaking, asphalt content, compaction, aggregate maximum size and temperature, influence on the indirect tensile strength and presented through a statistics analysis model for tensile strength in asphalt mixture

Effects of trunk stability on isometric knee extension muscle strength measurement while sitting.

Science.gov (United States)

Hirano, Masahiro; Gomi, Masahiro; Katoh, Munenori

2016-09-01

[Purpose] This study aimed to investigate the effect of trunk stability on isometric knee extension muscle strength measurement while sitting by performing simultaneous measurements with a handheld dynamometer (HHD) and an isokinetic dynamometer (IKD) in the same seated condition. [Subjects and Methods] The subjects were 30 healthy volunteers. Isometric knee extension muscle strength was simultaneously measured with a HHD and an IKD by using an IKD-specific chair. The measurement was performed twice. Measurement instrument variables and the number of measurements were examined by using the analysis of variance and correlation tests. [Results] The measurement instrument variables and the number of measurements were not significantly different. The correlation coefficients between the HHD and IKD measurements were ≥0.96. [Conclusion] Isometric knee extension muscle strength measurement using the HHD in the sitting position resulted in a lower value than that using the IKD, presumably because of the effect of trunk stability on the measurement. In the same seated posture with trunk stability, no significant difference in measurement values was observed between the HHD and IKD. The present findings suggest that trunk stability while seated during isometric knee extension muscle strength measurement influenced the HHD measurement.

Effects of functional exercise training on performance and muscle strength after meniscectomy

DEFF Research Database (Denmark)

Ericsson, Y B; Dahlberg, L E; Roos, E M

2008-01-01

Muscular deficits and functional limitations have been found years after meniscectomy of the knee. The purpose of this randomized controlled trial was to examine the effect of functional exercise training on functional performance and isokinetic thigh muscle strength in middle-aged patients...... subsequent to meniscectomy for a degenerative tear. Four years after meniscectomy, 45 patients (29 men, 16 women) were randomized to functional exercise training, supervised by a physical therapist, three times weekly for 4 months or to no intervention. The exercise program comprised of postural stability...... training and functional strength and endurance exercises for leg and trunk muscles. Outcomes were three functional performance tests and isokinetic muscle strength. Thirty patients (16 exercisers/14 controls) completed the study. Compared with control patients, the exercise group showed significant...

The Mediating Effect of Self-Efficacy in the Connections between Strength-Based Parenting, Happiness and Psychological Distress in Teens

OpenAIRE

Loton, Daniel J.; Waters, Lea E.

2017-01-01

Preliminary studies of strength-based parenting (SBP), a style of parenting that seeks to build strengths knowledge and strengths use in one’s child, have reported benefits such as higher life satisfaction, subjective wellbeing, and positive emotions together with lower stress in children and teens. Two proximal mediators conveying these effects have been identified: teen’s own use of strengths and strength-based coping, along with a small moderating effect of growth mindsets relating to stre...

Effect of interaction strength on robustness of controlling edge dynamics in complex networks

Science.gov (United States)

Pang, Shao-Peng; Hao, Fei

2018-05-01

Robustness plays a critical role in the controllability of complex networks to withstand failures and perturbations. Recent advances in the edge controllability show that the interaction strength among edges plays a more important role than network structure. Therefore, we focus on the effect of interaction strength on the robustness of edge controllability. Using three categories of all edges to quantify the robustness, we develop a universal framework to evaluate and analyze the robustness in complex networks with arbitrary structures and interaction strengths. Applying our framework to a large number of model and real-world networks, we find that the interaction strength is a dominant factor for the robustness in undirected networks. Meanwhile, the strongest robustness and the optimal edge controllability in undirected networks can be achieved simultaneously. Different from the case of undirected networks, the robustness in directed networks is determined jointly by the interaction strength and the network's degree distribution. Moreover, a stronger robustness is usually associated with a larger number of driver nodes required to maintain full control in directed networks. This prompts us to provide an optimization method by adjusting the interaction strength to optimize the robustness of edge controllability.

Ultrasound transmission measurements for tensile strength evaluation of tablets.

Science.gov (United States)

Simonaho, Simo-Pekka; Takala, T Aleksi; Kuosmanen, Marko; Ketolainen, Jarkko

2011-05-16

Ultrasound transmission measurements were performed to evaluate the tensile strength of tablets. Tablets consisting of one ingredient were compressed from dibasic calcium phosphate dehydrate, two grades of microcrystalline cellulose and two grades of lactose monohydrate powders. From each powder, tablets with five different tensile strengths were directly compressed. Ultrasound transmission measurements were conducted on every tablet at frequencies of 2.25 MHz, 5 MHz and 10 MHz and the speed of sound was calculated from the acquired waveforms. The tensile strength of the tablets was determined using a diametrical mechanical testing machine and compared to the calculated speed of sound values. It was found that the speed of sound increased with the tensile strength for the tested excipients. There was a good correlation between the speed of sound and tensile strength. Moreover, based on the statistical tests, the groups with different tensile strengths can be differentiated from each other by measuring the speed of sound. Thus, the ultrasound transmission measurement technique is a potentially useful method for non-destructive and fast evaluation of the tensile strength of tablets. Copyright © 2011 Elsevier B.V. All rights reserved.

Effects of contract-relax vs static stretching on stretch-induced strength loss and length-tension relationship

DEFF Research Database (Denmark)

Balle, S S; Magnusson, S P; McHugh, M P

2015-01-01

The purpose of this study was to determine the acute effects of contract-relax stretching (CRS) vs static stretching (SS) on strength loss and the length-tension relationship. We hypothesized that there would be a greater muscle length-specific effect of CRS vs SS. Isometric hamstring strength wa...

Effect of Resistance Training Frequency on Gains in Muscular Strength: A Systematic Review and Meta-Analysis.

Science.gov (United States)

Grgic, Jozo; Schoenfeld, Brad J; Davies, Timothy B; Lazinica, Bruno; Krieger, James W; Pedisic, Zeljko

2018-05-01

Current recommendations on resistance training (RT) frequency for gains in muscular strength are based on extrapolations from limited evidence on the topic, and thus their practical applicability remains questionable. To elucidate this issue, we conducted a systematic review and meta-analysis of the studies that compared muscular strength outcomes with different RT frequencies. To carry out this review, English-language literature searches of the PubMed/MEDLINE, Scopus, and SPORTDiscus databases were conducted. The meta-analysis was performed using a random-effects model. The meta-analysis models were generated with RT frequencies classified as a categorical variable as either 1, 2, 3, or 4+ times/week, or, if there were insufficient data in subgroup analyses, the training frequencies were categorized as 1, 2, or 3 times/week. Subgroup analyses were performed for potential moderators, including (1) training volume; (2) exercise selection for the 1 repetition maximum (RM) test (for both multi-joint and single-joint exercises); (3) upper and lower body strength gains; (4) training to muscular failure (for studies involving and not involving training to muscular failure); (5) age (for both middle-aged/older adults and young adults); and (6) sex (for men and for women). The methodological quality of studies was appraised using the modified Downs and Black checklist. A total of 22 studies were found to meet the inclusion criteria. The average score on the Downs and Black checklist was 18 (range 13-22 points). Four studies were classified as being of good methodological quality, while the rest were classified as being of moderate methodological quality. Results of the meta-analysis showed a significant effect (p = 0.003) of RT frequency on muscular strength gains. Effect sizes increased in magnitude from 0.74, 0.82, 0.93, and 1.08 for training 1, 2, 3, and 4+ times per week, respectively. A subgroup analysis of volume-equated studies showed no significant effect (p

Strongwomen® Program Evaluation: Effect of Strength Training Exercises on Physical Fitness of Participants

Science.gov (United States)

Chaudhary, Anil Kumar; Van Horn, Beth; Corbin, Marilyn

2015-01-01

The Strongwomen® Program (SWP) is a nationally disseminated group strength-training exercise and nutrition education program delivered by Extension. The study reported here examined the effect of strength training exercises in SWP on improvement in physical fitness of program participants. Senior Fitness Test was used to collect data. Upon…

Effects of In-Season Explosive Strength Training on Maximal Leg Strength, Jumping, Sprinting, and Intermittent Aerobic Performance in Male Handball Athletes.

Science.gov (United States)

Hermassi, Souhail; Chelly, Mohamed Souhaiel; Fieseler, Georg; Bartels, Thomas; Schulze, Stephan; Delank, Karl-Stefan; Shephard, Roy J; Schwesig, René

2017-09-01

Background  Team handball is an intense ball sport with specific requirements on technical skills, tactical understanding, and physical performance. The ability of handball players to develop explosive efforts (e. g. sprinting, jumping, changing direction) is crucial to success. Objective  The purpose of this pilot study was to examine the effects of an in-season high-intensity strength training program on the physical performance of elite handball players. Materials and methods  Twenty-two handball players (a single national-level Tunisian team) were randomly assigned to a control group (CG; n = 10) or a training group (TG; n = 12). At the beginning of the pilot study, all subjects performed a battery of motor tests: one repetition maximum (1-RM) half-squat test, a repeated sprint test [6 × (2 × 15 m) shuttle sprints], squat jumps, counter movement jumps (CMJ), and the Yo-Yo intermittent recovery test level 1. The TG additionally performed a maximal leg strength program twice a week for 10 weeks immediately before engaging in regular handball training. Each strength training session included half-squat exercises to strengthen the lower limbs (80 - 95 % of 1-RM, 1 - 3 repetitions, 3 - 6 sets, 3 - 4 min rest between sets). The control group underwent no additional strength training. The motor test battery was repeated at the end of the study interventions. Results  In the TG, 3 parameters (maximal strength of lower limb: η² = 0.74; CMJ: η² = 0.70, and RSA best time: η² = 0.25) showed significant improvements, with large effect sizes (e. g. CMJ: d = 3.77). A reduction in performance for these same 3 parameters was observed in the CG (d = -0.24). Conclusions  The results support our hypothesis that additional strength training twice a week enhances the maximal strength of the lower limbs and jumping or repeated sprinting performance. There was no evidence of shuttle sprints ahead of regular

Effect of a New Surface Treatment Solution on the Bond Strength of Composite to Enamel

Science.gov (United States)

2016-06-01

Bond Strength of Composite to Enamel " is appropriately acknowledged and, beyond brief excerpts, is with the permission of the copyright owner...Solution on the Bond Strength of Composite to Enamel ABSTRACT Clean & Boost (Apex Dental Materials) is a novel surface treatment solution...designed to be used in place of phosphoric acid to increase the bond strength of self-etch adhesives to enamel and more effectively remove contaminants

Effect of Dentin Wetness on the Bond Strength of Universal Adhesives

Directory of Open Access Journals (Sweden)

An-Na Choi

2017-10-01

Full Text Available The effects of dentin wetness on the bond strength and adhesive interface morphology of universal adhesives have been investigated using micro-tensile bond strength (μTBS testing and confocal laser scanning microscopy (CLSM. Seventy-two human third molars were wet ground to expose flat dentin surfaces. They were divided into three groups according to the air-drying time of the dentin surfaces: 0 (without air drying, 5, and 10 s. The dentin surfaces were then treated with three universal adhesives: G-Premio Bond, Single Bond Universal, and All-Bond Universal in self-etch or etch-and-rinse mode. After composite build up, a μTBS test was performed. One additional tooth was prepared for each group by staining the adhesives with 0.01 wt % of Rhodamine B fluorescent dye for CLSM analysis. The data were analyzed statistically using ANOVA and Tukey’s post hoc tests (α = 0.05. Two-way ANOVA showed significant differences among the adhesive systems and dentin moisture conditions. An interaction effect was also observed (p < 0.05. One-way ANOVA showed that All-Bond Universal was the only material influenced by the wetness of the dentin surfaces. Wetness of the dentin surface is a factor influencing the micro-tensile bond strength of universal adhesives.

A Multilevel Analysis of the Effects of Disciplinary Climate Strength on Student Reading Performance

Science.gov (United States)

Guo, Siwen; Li, Lingyan; Zhang, Danhui

2018-01-01

Climate strength was first conceptualised in the organisational psychology literature as the within-group agreement on the perceptions of climate. In contrast to the deep study of climate level, climate strength has not been clarified by school climate research. The purpose of this cross-cultural study is to identify the main effect of…

Effect of strength training with blood flow restriction on muscle power and submaximal strength in eumenorrheic women.

Science.gov (United States)

Gil, Ana L S; Neto, Gabriel R; Sousa, Maria S C; Dias, Ingrid; Vianna, Jeferson; Nunes, Rodolfo A M; Novaes, Jefferson S

2017-03-01

Blood flow restriction (BFR) training stimulates muscle size and strength by increasing muscle activation, accumulation of metabolites and muscle swelling. This method has been used in different populations, but no studies have evaluated the effects of training on muscle power and submaximal strength (SS) in accounted for the menstrual cycle. The aim of this study was to analyse the effect of strength training (ST) with BFR on the muscle power and SS of upper and lower limbs in eumenorrheic women. Forty untrained women (18-40 years) were divided randomly and proportionally into four groups: (i) high-intensity ST at 80% of 1RM (HI), (ii) low-intensity ST at 20% of 1RM combined with partial blood flow restriction (LI + BFR), (iii) low-intensity ST at 20% of 1RM (LI) and d) control group (CG). Each training group performed eight training sessions. Tests with a medicine ball (MB), horizontal jump (HJ), vertical jump (VJ), biceps curls (BC) and knee extension (KE) were performed during the 1st day follicular phase (FP), 14th day (ovulatory phase) and 26-28th days (luteal phase) of the menstrual cycle. There was no significant difference among groups in terms of the MB, HJ, VJ or BC results at any time point (P>0·05). SS in the KE exercise was significantly greater in the LI + BFR group compared to the CG group (P = 0·014) during the LP. Therefore, ST with BFR does not appear to improve the power of upper and lower limbs and may be an alternative to improve the SS of lower limbs of eumenorrheic women. © 2015 Scandinavian Society of Clinical Physiology and Nuclear Medicine. Published by John Wiley & Sons Ltd.

Effect of Irradiation on the Shear Bond Strength of Self-adhesive ...

African Journals Online (AJOL)

2016-02-05

Feb 5, 2016 ... changes in the crystalline structure of dental hard tissues. Keywords: Bond strength, irradiation, self-adhesive luting cement. Effect of Irradiation on the .... The metal ring was connected with the cross-head and loaded (speed 1 ...

The Mediating Effect of Self-Efficacy in the Connections between Strength-Based Parenting, Happiness and Psychological Distress in Teens

Directory of Open Access Journals (Sweden)

Daniel J. Loton

2017-10-01

Full Text Available Preliminary studies of strength-based parenting (SBP, a style of parenting that seeks to build strengths knowledge and strengths use in one’s child, have reported benefits such as higher life satisfaction, subjective wellbeing, and positive emotions together with lower stress in children and teens. Two proximal mediators conveying these effects have been identified: teen’s own use of strengths and strength-based coping, along with a small moderating effect of growth mindsets relating to strengths. The current study tests the potential mediating effect of self-efficacy, a sense of agency in life, in the relationship between SBP and mental health (wellbeing and illbeing in teens. Self efficacy has been linked to wellbeing and strengths processes in past studies and is classed as a basic human need and form of eudaimonic happiness. This study reconfirmed the adaptive benefits of SBP in a large sample of Australian adolescents (N = 11,368; 59% male; Mage = 14.04, SDage = 1.99 sourced from 28 schools. Using structural equation modeling, SBP significantly and directly predicted higher happiness and lower depression, with direct effects falling into the 85th and 95th percentile of meta-analytically derived individual differences effect sizes. In addition, self-efficacy was a significant partial mediator, accounting for 40.0% of the total effect on happiness and 52.7% of the total effect on distress. Self-efficacy was also a full mediator in the case of anxiety, with a strong indirect effect. Results suggest that building strengths in teens can also build self-efficacy, and given the large effect sizes, that SBP is a promising leverage point for increasing teen wellbeing.

The Effect of Weight-Bearing Exercise on the Strength of Femur Bone in Ovariectomized Rats

Directory of Open Access Journals (Sweden)

GH Sharifi

2011-08-01

Full Text Available Introduction & Objective: Fractures due to osteoporosis after menopause in women is widespread. Osteoporosis may occur in case of inadequate lack of physical activity .The aim of this study was to determine the effect of running training on femur bone strength in ovariectomized rats. Materials & Methods Forty matured Sprague Dawley rats were chosen for this study. A group of 10 were killed randomly to measure their initial femur strength. The remaining rats had ovarian surgery. After three months, in order to reach menopause period, they were randomly divided into 3 groups, including pre test, running training and control groups. The running training program was carried out for one hour a day, five days a week, for eight weeks. Femur bone strength was measured by HOUNSFIELD system. Data was analyzed by using one-way analysis of variance and dependent T- tests by the SPSS software. Results: Results of this study showed that ovariectomy leads to significant decrease of femur bone strength. On the other hand the eight weeks running training lead to significant increase of femur bone strength. Conclusion: The results of this study suggest that life style is important factors in preventing of osteoporosis and running training program had an inhibitory or reversal effect on decrease of menopause-induced femur bone strength.

Investigating the Effects of Typical Rowing Strength Training Practices on Strength and Power Development and 2,000 m Rowing Performance

Directory of Open Access Journals (Sweden)

Ian Gee Thomas

2016-04-01

Full Text Available This study aimed to determine the effects of a short-term, strength training intervention, typically undertaken by club-standard rowers, on 2,000 m rowing performance and strength and power development. Twenty-eight male rowers were randomly assigned to intervention or control groups. All participants performed baseline testing involving assessments of muscle soreness, creatine kinase activity (CK, maximal voluntary contraction (leg-extensors (MVC, static-squat jumps (SSJ, counter-movement jumps (CMJ, maximal rowing power strokes (PS and a 2,000 m rowing ergometer time-trial (2,000 m with accompanying respiratory-exchange and electromyography (EMG analysis. Intervention group participants subsequently performed three identical strength training (ST sessions, in the space of five days, repeating all assessments 24 h following the final ST. The control group completed the same testing procedure but with no ST. Following ST, the intervention group experienced significant elevations in soreness and CK activity, and decrements in MVC, SSJ, CMJ and PS (p < 0.01. However, 2,000 m rowing performance, pacing strategy and gas exchange were unchanged across trials in either condition. Following ST, significant increases occurred for EMG (p < 0.05, and there were non-significant trends for decreased blood lactate and anaerobic energy liberation (p = 0.063 – 0.086. In summary, club-standard rowers, following an intensive period of strength training, maintained their 2,000 m rowing performance despite suffering symptoms of muscle damage and disruption to muscle function. This disruption likely reflected the presence of acute residual fatigue, potentially in type II muscle fibres as strength and power development were affected.

Effect of Isothermal Bainitic Quenching on Rail Steel Impact Strength and Wear Resistance

Science.gov (United States)

Çakir, Fatih Hayati; Çelik, Osman Nuri

2017-09-01

The effect of heat treatment regimes on hardness, impact strength, and wear resistance of rail steel for high-speed tracks (rail quality category R350HT) is studied. Analysis of steel properties with a different structure is compared: pearlitic, and upper and lower bainite. It is shown that the steel with bainitic structure has the best impact strength, but wear resistance is better for steel with a lower bainite structure.

Analysis of responsive characteristics of ionic-strength-sensitive hydrogel with consideration of effect of equilibrium constant by a chemo-electro-mechanical model.

Science.gov (United States)

Li, Hua; Lai, Fukun; Luo, Rongmo

2009-11-17

A multiphysics model is presented in this paper for analysis of the influence of various equilibrium constants on the smart hydrogel responsive to the ionic strength of environmental solution, and termed the multieffect-coupling ionic-strength stimulus (MECis) model. The model is characterized by a set of partial differential governing equations by consideration of the mass and momentum conservations of the system and coupled chemical, electrical, and mechanical multienergy domains. The Nernst-Planck equations are derived by the mass conservation of the ionic species in both the interstitial fluid of the hydrogel and the surrounding solution. The binding reaction between the fixed charge groups of the hydrogel and the mobile ions in the solution is described by the fixed charge equation, which is based on the Langmuir monolayer theory. As an important effect for the binding reaction, the equilibrium constant is incorporated into the fixed charge equation. The kinetics of the hydrogel swelling/deswelling is illustrated by the mechanical equation, based on the law of momentum conservation for the solid polymeric networks matrix within the hydrogel. The MECis model is examined by comparison of the numerical simulations and experiments from open literature. The analysis of the influence of different equilibrium constants on the responsive characteristics of the ionic-strength-sensitive hydrogel is carried out with detailed discussion.

Carbon fiber/carbon nanotube reinforced hierarchical composites: Effect of CNT distribution on shearing strength

DEFF Research Database (Denmark)

Zhou, H. W.; Mishnaevsky, Leon; Yi, H. Y.

2016-01-01

The strength and fracture behavior of carbon fiber reinforced polymer composites with carbon nanotube (CNT) secondary reinforcement are investigated experimentally and numerically. Short Beam Shearing tests have been carried out, with SEM observations of the damage evolution in the composites. 3D...... CNT nanoreinforcement into the matrix and/or the sizing of carbon fiber/reinforced composites ensures strong increase of the composite strength. The effect of secondary CNTs reinforcement is strongest when some small addition of CNTs in the polymer matrix is complemented by the fiber sizing with high...... multiscale computational (FE) models of the carbon/polymer composite with varied CNT distributions have been developed and employed to study the effect of the secondary CNT reinforcement, its distribution and content on the strength and fracture behavior of the composites. It is shown that adding secondary...

The Effect of Polymer-Cement Stabilization on the Unconfined Compressive Strength of Liquefiable Soils

Directory of Open Access Journals (Sweden)

Ali Ateş

2013-01-01

Full Text Available Soil stabilization has been widely used as an alternative to substitute the lack of suitable material on site. The use of nontraditional chemical stabilizers in soil improvement is growing daily. In this study a laboratory experiment was conducted to evaluate the effects of waterborne polymer on unconfined compression strength and to study the effect of cement grout on pre-venting of liquefiable sandy soils. The laboratory tests were performed including grain size of sandy soil, unit weight, ultrasonic pulse velocity, and unconfined compressive strength test. The sand and various amounts of polymer (1%, 2%, 3%, and 4% and cement (10%, 20%, 30%, and 40% were mixed with all of them into dough using mechanical kneader in laboratory conditions. Grouting experiment is performed with a cylindrical mould of  mm. The samples were subjected to unconfined compression tests to determine their strength after 7 and 14 days of curing. The results of the tests indicated that the waterborne polymer significantly improved the unconfined compression strength of sandy soils which have susceptibility of liquefaction.

The Effects of Different Curing Methods on the Compressive Strength of Terracrete

Directory of Open Access Journals (Sweden)

O. Alake

2009-01-01

Full Text Available This research evaluated the effects of different curing methods on the compressive strength of terracrete. Several tests that included sieve analysis were carried out on constituents of terracrete (granite and laterite to determine their particle size distribution and performance criteria tests to determine compressive strength of terracrete cubes for 7 to 35 days of curing. Sand, foam-soaked, tank and open methods of curing were used and the study was carried out under controlled temperature. Sixty cubes of 100 × 100 × 100mm sized cubes were cast using a mix ratio of 1 part of cement, 1½ part of latrite, and 3 part of coarse aggregate (granite proportioned by weight and water – cement ratio of 0.62. The result of the various compressive strengths of the cubes showed that out of the four curing methods, open method of curing was the best because the cubes gained the highest average compressive strength of 10.3N/mm2 by the 35th day.

Effect of light aging on silicone-resin bond strength in maxillofacial prostheses.

Science.gov (United States)

Polyzois, Gregory; Pantopoulos, Antonis; Papadopoulos, Triantafillos; Hatamleh, Muhanad

2015-04-01

The aim of this study was to investigate the effect of accelerated light aging on bond strength of a silicone elastomer to three types of denture resin. A total of 60 single lap joint specimens were fabricated with auto-, heat-, and photopolymerized (n = 20) resins. An addition-type silicone elastomer (Episil-E) was bonded to resins treated with the same primer (A330-G). Thirty specimens served as controls and were tested after 24 hours, and the remaining were aged under accelerated exposure to daylight for 546 hours (irradiance 765 W/m(2) ). Lap shear joint tests were performed to evaluate bond strength at 50 mm/min crosshead speed. Two-way ANOVA and Tukey's test were carried out to detect statistical significance (p Accelerated light aging for 546 hours affects the bond strength of an addition-type silicone elastomer to three different denture resins. The bond strength significantly increased after aging for photo- and autopolymerized resins. All the bonds failed adhesively. © 2014 by the American College of Prosthodontists.

Effect of water curing duration on strength behaviour of portland composite cement (PCC) mortar

Science.gov (United States)

Caronge, M. A.; Tjaronge, M. W.; Hamada, H.; Irmawaty, R.

2017-11-01

Cement manufacturing of Indonesia has been introduced Portland Composite Cement (PCC) to minimize the rising production cost of cement which contains 80% clinker and 20% mineral admixture. A proper curing is very important when the cement contains mineral admixture materials. This paper reports the results of an experimental study conducted to evaluate the effect of water curing duration on strength behaviour of PCC mortar. Mortar specimens with water to cement ratio of (W/C) 0.5 were casted. Compressive strength, flexural strength and concrete resistance were tested at 7, 28 and 91 days cured water. The results indicated that water curing duration is essential to continue the pozzolanic reaction in mortar which contributes to the development of strength of mortar made with PCC.

The Effect of Antidepressants on Mesenchymal Stem Cell Differentiation.

Science.gov (United States)

Kruk, Jeffrey S; Bermeo, Sandra; Skarratt, Kristen K; Fuller, Stephen J; Duque, Gustavo

2018-02-01

Use of antidepressant medications has been linked to detrimental impacts on bone mineral density and osteoporosis; however, the cellular basis behind these observations remains poorly understood. The effect does not appear to be homogeneous across the whole class of drugs and may be linked to affinity for the serotonin transporter system. In this study, we hypothesized that antidepressants have a class- and dose-dependent effect on mesenchymal stem cell (MSC) differentiation, which may affect bone metabolism. Human MSCs (hMSCs) were committed to differentiate when either adipogenic or osteogenic media was added, supplemented with five increasing concentrations of amitriptyline (0.001-10 µM), venlafaxine (0.01-25 µM), or fluoxetine (0.001-10 µM). Alizarin red staining (mineralization), alkaline phosphatase (osteoblastogenesis), and oil red O (adipogenesis) assays were performed at timed intervals. In addition, cell viability was assessed using a MTT. We found that fluoxetine had a significant inhibitory effect on mineralization. Furthermore, adipogenic differentiation of hMSC was affected by the addition of amitriptyline, venlafaxine, and fluoxetine to the media. Finally, none of the tested medications significantly affected cell survival. This study showed a divergent effect of three antidepressants on hMSC differentiation, which appears to be independent of class and dose. As fluoxetine and amitriptyline, but not venlafaxine, affected both osteoblastogenesis and adipogenesis, this inhibitory effect could be associated to the high affinity of fluoxetine to the serotonin transporter system.

Effects of residual stress on fatigue strength of small diameter welded pipe joint

International Nuclear Information System (INIS)

Yamashita, Tetsuo; Hattori, Takahiro; Nomoto, Toshiharu; Iida, Kunihiro; Sato, Masanobu

1996-01-01

A power plant consists of many welded components, therefore, it is essential in establishing the reliability of the power plant to maintain the reliability of all welded components. The fatigue failure caused by mechanical vibrations of small diameter welded joints, which is represented by socket welded joints, is one of the major causes of trouble for the welded parts of the power plant. Here, bending fatigue tests were conducted to investigate the fatigue strength of small diameter socket welded pipe joints. In the most cases of large diameter socket joints, a fatigue crack started from the root of the fillet weld though the stress amplitude at the root was smaller than that at the toe of fillet weld. Additionally, the fatigue strength was affected by the weld bead sequence. The residual stress was considered to be one of the important parameters governing fatigue strength, therefore, its effects were investigated. In several types of pipe joints, the local stress and residual stress distributions were calculated by finite element analysis. The residual stresses were compressive at the toe and tensile at the root of the socket welded joints. Based on these results, the effects of residual stresses on the fatigue strength are discussed for small diameter welded pipe joints in the present work

ZrO2 nanoparticles' effects on split tensile strength of self compacting concrete

Directory of Open Access Journals (Sweden)

Ali Nazari

2010-12-01

Full Text Available In the present study, split tensile strength of self compacting concrete with different amount of ZrO2 nanoparticles has been investigated. ZrO2 nanoparticles with the average particle size of 15 nm were added partially to cement paste (Portland cement together with polycarboxylate superplasticizer and split tensile strength of the specimens has been measured. The results indicate that ZrO2 nanoparticles are able to improve split tensile strength of concrete and recover the negative effects of polycarboxylate superplasticizer. ZrO2 nanoparticle as a partial replacement of cement up to 4 wt. (% could accelerate C-S-H gel formation as a result of increased crystalline Ca(OH2 amount at the early age of hydration. The increased the ZrO2 nanoparticles' content more than 4 wt. (%, causes the reduced the split tensile strength because of unsuitable dispersion of nanoparticles in the concrete matrix.

Effect of hot-humid exposure on static strength of adhesive-bonded aluminum alloys

Directory of Open Access Journals (Sweden)

Rui Zheng

2015-09-01

Full Text Available The effect of hot-humid exposure (i.e., 40 °C and 98% R.H. on the quasi-static strength of the adhesive-bonded aluminum alloys was studied. Test results show that the hot-humid exposure leads to the significant decrease in the joint strength and the change of the failure mode from a mixed cohesive and adhesive failure with cohesive failure being dominant to adhesive failure being dominant. Careful analyses of the results reveal that the physical bond is likely responsible for the bond adhesion between L adhesive and aluminum substrates. The reduction in joint strength and the change of the failure mode resulted from the degradation in bond adhesion, which was primarily attributed to the corrosion of aluminum substrate. In addition, the elevated temperature exposure significantly accelerated the corrosion reaction of aluminum, which accelerated the degradation in joint strength.

Initial Effect of Taping Technique on Wrist Extension and Grip Strength and Pain of Individuals with Lateral Epicondylitis

Directory of Open Access Journals (Sweden)

Alireza Shamsoddini

2010-04-01

Full Text Available Objectives: Aim of this study is to investigate the initial effect of taping technique on wrist extension and grip strength and pain of Individuals with tennis elbow. Methods: fifteen patients (10 men and 5 women with 42.53 years on their dominant arm participated in this study. Outcome measures were wrist extension and grip strength and pain taken before and immediately after application of tape. The unaffected arm served as a control. Used of hand-held dynamometer and jammar dynamometer for evaluated of wrist extension and grip strength. Also, visual analog scale (VAS used for evaluated of pain Results: Among the variables, significant differences were found in wrist extension strength between effected and unaffected arm (P=0.006. Also, changes in grip strength shows statically significant improve in effect arm than unaffected arm (P=0.001. Changes in pain in impaired arm were positive. Discussion: Taping technique, as applied in this study demonstrated an impressive effect on wrist extension and grip strength and pain in individuals with tennis elbow. Therefore, it is recommended that this method may be useful in the management of this condition during exercise and functional rehabilitation.

Effect Of Superfluidity And Differential Rotation Of Quark Matter On Magetic Field Evolution in Neutron Star And Black Hole

Science.gov (United States)

Aurongzeb, Deeder

2010-11-01

Anomalous X-ray pulsars and soft gamma-ray repeaters reveal that existence of very strong magnetic field(> 10e15G) from neutron stars. It has been estimated that at the core the magnitude can be even higher at the center. Apart from dynamo mechanism it has been shown that color locked ferromagnetic phase [ Phys. Rev. D. 72,114003(2005)] can be a possible origin of magnetic field. In this study, we explore electric charge of strange quark matter and its effect on forming chirality in the quark-gluon plasma. We show that electromagnetic current induced by chiral magnetic effect [(Phys. Rev. D. 78.07033(2008)] can induce differential rotation in super fluid quark-gluon plasma giving additional boost to the magnetic field. The internal phase and current has no effect from external magnetic field originating from active galactic nuclei due to superconducting phase formation which screens the fields due to Meissner effect. We show that differential motion can create high radial electric field at the surface making all radiation highly polarized and directional including thermal radiation. As the electric field strength can be even stronger for a collapsing neutron star, the implication of this study to detect radiation from black holes will also be discussed. The work was partly completed at the University of Texas at austin

Effect of bar sealing parameters on OPP/MCPP heat seal strength

Directory of Open Access Journals (Sweden)

2007-11-01

Full Text Available The effect of bar sealing parameters on the heat seal strength of oriented polypropylene (OPP/metallic cast polypropylene (MCPP laminate film was investigated. Based on the results obtained from the parametric study, a bar sealing process window was developed. All points drop within the process window are combinations of platen temperature and dwell time that produce acceptable heat seal. Optimum combinations are indicated by the lower border of the window. The plateau initiation temperature, Tpi of OPP/MCPP laminate film used in the present study occurred before the final melting temperature, Tmf of the sealant material. The highest achievable heat seal strength was at the plateau region, and the corresponding failure modes were delaminating, tearing or combine failure modes (delaminating and tearing. Minimum pressure level of 1.25 bars is necessary to bring the laminate interface into intimate contact in order to effect sealing.

THE EFFECTS OF ISOKINETIC KNEE STRENGTH ON THE PROMPTNESS OF SOCCER PLAYERS

OpenAIRE

Ali Kerim Yilmaz; Menderes Kabadayi; Muhammet Hakan Mayda; Murşit Ceyhun Birinci; Mustafa Özdal

2017-01-01

The purpose of this study is to examine the effects of isokinetic knee strength on promptness. 15 soccer players with an average age of 22,80±2,14 years and 15 controls with an average age of 21,60±1,40 years participated in the study. Body composition, isokinetic knee strength measurement at angular speeds of 60o, 180o, 240o and 10 m sprint test were conducted respectively in the study. General warm-up procedure was carried out on the groups before measurements. In statistical analyses, Shap...

Effect of the conditions of prepreg preparation on the strength of structural plastics

Science.gov (United States)

Zaborskaya, L. V.; Yurkevich, O. R.

1995-05-01

A study is made of the effect of the temperature and duration of heat treatment of polymer composite prepregs on their strength. It is established that heat treatment under conditions ensuring close to maximal adhesive interaction between the components of the prepreg and subsequent shaping makes it possible to more than double the strength of the plastic (Table 1), A new approach is proposed to optimizing the conditions of formation of structural plastics.

Differentiated-effect shims for medium field levels and saturation

International Nuclear Information System (INIS)

Richie, A.

1976-01-01

The arrangement of shims on the upstream and downstream ends of magnets may be based on the independent effects of variations in the geometric length and degree of saturation at the edges of the poles. This technique can be used to match the bending strength of an accelerator's magnets at two field levels (medium fields and maximum fields) and thus save special procedures (mixing the laminations, local compensation for errors by arranging the magnets in the appropriate order) and special devices (for instance, correcting dipoles) solely for correcting bending strengths at low field levels. (Auth.)

The acute effect of match play on hamstring strength and lower limb flexibility in elite youth football players

DEFF Research Database (Denmark)

Wollin, M; Thorborg, K; Pizzari, T

2017-01-01

. Competitive football match play has a significant acute and transient effect on isometric hamstring strength and associated pain levels during resisted knee flexion in male international youth players. Range of motion measures appear to remain relatively unaffected by match play. Isometric hamstring strength......The aim of this study was to investigate the effect of competitive football match play on hamstring strength and lower limb flexibility. Fifteen male international youth football players were included. Hamstring strength and associated pain ratings, ankle dorsiflexion, hip extension, knee extension...... and flexion range of motion were evaluated immediately post-match and at intervals of 24, 48, and 72 h post-match. Strength significantly reduced post-match (P

The effect of edge interlaminar stresses on the strength of carbon/epoxy laminates of different stacking geometry

OpenAIRE

MOMCILO STEVANOVIC; MILAN GORDIC; DANIELA SEKULIC; ISIDOR DJORDJEVIC

2006-01-01

The effect of edge interlaminar stresses on strength of carbon/epoxy laminates of different stacking geometry: cross-ply, quasi-isotropic and angle-ply laminates with additional 0º and 90º ply was studied. Coupons with two widths of laminates with an inverse stacking sequence were tested in static tensile tests. The effect of edge interlaminar stresses on strength was studied, by comparing the values of the tensile strength of laminate coupons of the same width with an inverse stacking sequen...

Effect of water absorption by the aggregate on properties of high-strength lightweight concrete

Energy Technology Data Exchange (ETDEWEB)

Punkki, J

1996-12-31

Recently, high-strength lightweight concrete has become an interesting building material for the offshore oil industry. This doctoral thesis presents an experimental investigation of the effect of water absorption by three different types of lightweight aggregates. One type did not show any water absorption ability at all and so represented no problem to the concrete production. For the two other high-strength aggregates, which were of more conventional types, the water absorption depended not only on the properties of the aggregates, but also on the concrete mixing procedure and the properties of the fresh cement paste. When water absorbing lightweight aggregate was used in a dry condition, the workability of the concrete was significantly reduced by the water absorption of the aggregate. This effect was not present when prewetted aggregate was used. The water absorption by the lightweight aggregate also affected the early compressive strength of concrete. After one day, dry aggregate gave on the average 10 MPa higher compressive strength than did prewetted aggregate. The strength-density ratio was affected by the moisture condition of the aggregate. Dry lightweight aggregate gave 9 MPa higher compressive strength at a density of 2000 kg/m{sup 3} compared to that of prewetted aggregate. The water absorption by the lightweight also affected the microstructure of the hardened concrete. Dry lightweight aggregate gave a slightly better microstructure than normal weight aggregate. The results indicate that the use of prewetted aggregate adversely affected the transition zone between the aggregate and the cement paste. 69 refs., 58 figs., 42 tabs.

Effect of water absorption by the aggregate on properties of high-strength lightweight concrete

Energy Technology Data Exchange (ETDEWEB)

Punkki, J.

1995-12-31

Recently, high-strength lightweight concrete has become an interesting building material for the offshore oil industry. This doctoral thesis presents an experimental investigation of the effect of water absorption by three different types of lightweight aggregates. One type did not show any water absorption ability at all and so represented no problem to the concrete production. For the two other high-strength aggregates, which were of more conventional types, the water absorption depended not only on the properties of the aggregates, but also on the concrete mixing procedure and the properties of the fresh cement paste. When water absorbing lightweight aggregate was used in a dry condition, the workability of the concrete was significantly reduced by the water absorption of the aggregate. This effect was not present when prewetted aggregate was used. The water absorption by the lightweight aggregate also affected the early compressive strength of concrete. After one day, dry aggregate gave on the average 10 MPa higher compressive strength than did prewetted aggregate. The strength-density ratio was affected by the moisture condition of the aggregate. Dry lightweight aggregate gave 9 MPa higher compressive strength at a density of 2000 kg/m{sup 3} compared to that of prewetted aggregate. The water absorption by the lightweight also affected the microstructure of the hardened concrete. Dry lightweight aggregate gave a slightly better microstructure than normal weight aggregate. The results indicate that the use of prewetted aggregate adversely affected the transition zone between the aggregate and the cement paste. 69 refs., 58 figs., 42 tabs.

High-intensity intermittent exercise and its effects on heart rate variability and subsequent strength performance

Directory of Open Access Journals (Sweden)

Valéria Leme Gonçalves Panissa

2016-03-01

Full Text Available PRUPOSE: To investigate the effects of a 5-km high-intensity interval exercise (HIIE on heart rate variability (HRV and subsequent strength performance. METHODS: nine trained males performed a control session composed of a half-squat strength exercise (4 x 80% of one repetition maximum – 1RM in isolation and 30-min, 1-, 4-, 8- and 24-h after an HIIE (1-min at the velocity peak:1-min passive recovery. All experimental sessions were performed on different days. The maximum number of repetitions and total weight lifted during the strength exercise were registered in all conditions; in addition, prior to each session, HRV were assessed [beat-to-beat intervals (RR and log-transformed of root means square of successive differences in the normal-to-normal intervals (lnRMSSD]. RESULTS: Performance in the strength exercise dropped at 30-min (31% and 1-h (19% post-HIIE concomitantly with lower values of RR (781±79 ms; 799±134 ms, respectively in the same recovery intervals compared to the control (1015±197 ms. Inferential analysis did not detect any effect of condition on lnRMSSD, however, values were lower after 30-min (3.5±0.4 ms and 1-h (3.3±0.5 ms with moderate and large effect sizes (0.9 and 1.2, respectively compared with the control condition (3.9±0.4 ms. CONCLUSION: Both RR and lnRMSSD seem to be associated with deleterious effects on strength performance, although further studies should be conducted to clarify this association.

Temperature effect compensation for fast differential pressure decay testing

International Nuclear Information System (INIS)

Shi, Yan; Tong, Xiaomeng; Cai, Maolin

2014-01-01

To avoid the long temperature recovery period with differential pressure decay for leak detection, a novel method with temperature effect compensation is proposed to improve the testing efficiency without full stabilization of temperature. The mathematical model of conventional differential pressure decay testing is established to analyze the changes of temperature and pressure during the measuring period. Then the differential pressure is divided into two parts: the exponential part caused by temperature recovery and the linear part caused by leak. With prior information obtained from samples, parameters of the exponential part can be identified precisely, and the temperature effect will be compensated before it fully recovers. To verify the effect of the temperature compensated method, chambers with different volumes are tested under various pressures and the experiments show that the improved method is faster with satisfactory precision, and an accuracy less than 0.25 cc min −1  can be achieved when the compensation time is proportional to four times the theoretical thermal-time constant. (paper)

Effect of Curing Direction on Microtensile Bond Strength of Fifth and Sixth Generation Dental Adhesives

Directory of Open Access Journals (Sweden)

Ali Nadaf

2012-09-01

Full Text Available Background and Aims: Composite restorative materials and dental adhesives are usually cured with light sources. The light direction may influence the bond strength of dental adhesives. The aim of this study was to evaluate the effect of light direction on the microtensile bond strength of fifth and sixth generation dental adhesives.Materials and Methods: Prime & Bond NT and Clearfil SE bond were used with different light directions.Sixty human incisor teeth were divided into 4 groups (n=15. In groups A and C, Clearfil SE bond with light curing direction from buccal was used for bonding a composite resin to dentin. In groups B and D, Prime & Bond NT with light curing direction from composite was used. After thermocycling the specimens were subjected to tensile force until debonding occurred and values for microtensile bond strength were recorded. The data were analyzed using two-way ANOVA and Tukey post hoc test.Results: The findings showed that the bond strength of Clearfil SE bond was significantly higher than that of Prime&Bond NT (P<0.001. There was no significant difference between light curing directions (P=0.132.Conclusion: Light curing direction did not have significant effect on the bond strength. Sixth generation adhesives was more successful than fifth generation in terms of bond strength to dentin.

Reference Values of Grip Strength, Prevalence of Low Grip Strength, and Factors Affecting Grip Strength Values in Chinese Adults.

Science.gov (United States)

Yu, Ruby; Ong, Sherlin; Cheung, Osbert; Leung, Jason; Woo, Jean

2017-06-01

The objectives of this study were to update the reference values of grip strength, to estimate the prevalence of low grip strength, and to examine the impact of different aspects of measurement protocol on grip strength values in Chinese adults. A cross-sectional survey of Chinese men (n = 714) and women (n = 4014) aged 18-102 years was undertaken in different community settings in Hong Kong. Grip strength was measured with a digital dynamometer (TKK 5401 Grip-D; Takei, Niigata, Japan). Low grip strength was defined as grip strength 2 standard deviations or more below the mean for young adults. The effects of measurement protocol on grip strength values were examined in a subsample of 45 men and women with repeated measures of grip strength taken with a hydraulic dynamometer (Baseline; Fabrication Enterprises Inc, Irvington, NY), using pair t-tests, intraclass correlation coefficient, and Bland and Altman plots. Grip strength was greater among men than among women (P values than the Baseline hydraulic dynamometer (P values were also observed when the measurement was performed with the elbow extended in a standing position, compared with that with the elbow flexed at 90° in a sitting position, using the same dynamometer (P values of grip strength and estimated the prevalence of low grip strength among Chinese adults spanning a wide age range. These findings might be useful for risk estimation and evaluation of interventions. However, grip strength measurements should be interpreted with caution, as grip strength values can be affected by type of dynamometer used, assessment posture, and elbow position. Copyright © 2017 AMDA – The Society for Post-Acute and Long-Term Care Medicine. Published by Elsevier Inc. All rights reserved.

Effect of surface treatment of FRC-Post on bonding strength to resin cements

Directory of Open Access Journals (Sweden)

Chan-Hyun Park,

2011-03-01

Full Text Available Objectives The purpose of this study was to evaluate the effect of surface treatment of FRC-Post on bonding strength to resin cements. Materials and Methods Pre-surface treated LuxaPost (DMG, Rely-X Fiber Post (3M ESPE and self adhesive resin cement Rely-X Unicem (3M ESPE, conventional resin cement Rely-X ARC (3M ESPE, and Rely-X Ceramic Primer (3M ESPE were used. After completing the surface treatments of the posts, posts and resin cement were placed in clear molds and photo-activation was performed. The specimens were sectioned perpendicular to the FRC-Post into 2 mm-thick segments, and push-out strength were measured. The results of bond strength value were statistically analyzed using independent samples t-test and one-way ANOVA with multiple comparisons using Scheffe's test. Results Silanization of posts affect to the bond strength in LuxaPost, and did not affect in Rely-X Fiber Post. Rely-X ARC showed higher value than Rely-X Unicem. Conclusions Silanization is needed to enhance the bond strength between LuxaPost and resin cements.

Irreversible traps, their influence on the embrittlement of high strength steel

International Nuclear Information System (INIS)

Mariano, I; Mansilla, G

2012-01-01

Hydrogen (H) can be trapped in lattice defects such as vacancies, dislocations, grain boundaries and interfaces between the matrix and precipitates. The effect on the mechanical properties depends on factors inherent in materials such as the activation energy of irreversible traps (H trapped in Network Places) and its sensitivity to embrittlement. Differential scanning calorimetry (DSC) allows the study of those processes in which enthalpy variation occurs. The purpose is to record the difference in enthalpy change that occurs in the sample as a function of temperature or time. This work represents a study of H embrittlement of high strength steel resulfurized

The Effects of Extravehicular Activity (EVA) Glove Pressure on Hand Strength

Science.gov (United States)

Mesloh, Miranda; England, Scott; Benson, Elizabeth; Thompson, Shelby; Rajulu, Sudhakar

2010-01-01

The purpose of this study was to characterize hand strength, while wearing a Phase VI Extravehicular Activity (EVA) glove in an Extravehicular Mobility Unit (EMU) suit. Three types of data were collected: hand grip, lateral pinch, and pulp-2 pinch, wider three different conditions: bare-handed, gloved with no Thermal Micrometeoroid Garment (TMG), and glove with TMG. In addition, during the gloved conditions, subjects were tested when unpressurized and pressurized (43 psi). As a percentage of bare-hand strength, the TMG condition showed reduction in grip strength to 55% unpressurized and 46% pressurized. Without the TMG, grip strength increased to 66% unpressurized and 58% pressurized of bare-hand strength. For lateral pinch strength, the reduction in strength was the same for both pressure conditions and with and without the TMG, about 8.5% of bare-hand Pulp-2 pinch strength with no TMG showed an increase to 122% unpressurized and 115% pressurized of bare-hand strength. While wearing the TMG, pulp-2 pinch strength was 115% of bare-hand strength for both pressure conditions.

The effect of processing on autohesive strength development in thermoplastic resins and composites

Science.gov (United States)

Howes, Jeremy C.; Loos, Alfred C.; Hinkley, Jeffrey A.

1989-01-01

In the present investigation of processing effects on the autohesive bond strength of neat polysulfone resin and graphite-reinforced polysulfone-matrix composites measured resin bond strength development in precracked compact tension specimens 'healed' by heating over a contact period at a given temperature. The critical strain energy release rate of refractured composite specimens did not exhibit the strong time or temperature dependence of the neat resin tests; only 80-90 percent of the undamaged fracture energy is recoverable.

The Mediating Effect of Self-Efficacy in the Connections between Strength-Based Parenting, Happiness and Psychological Distress in Teens.

Science.gov (United States)

Loton, Daniel J; Waters, Lea E

2017-01-01

Preliminary studies of s trength-based parenting (SBP), a style of parenting that seeks to build strengths knowledge and strengths use in one's child, have reported benefits such as higher life satisfaction, subjective wellbeing, and positive emotions together with lower stress in children and teens. Two proximal mediators conveying these effects have been identified: teen's own use of strengths and strength-based coping, along with a small moderating effect of growth mindsets relating to strengths. The current study tests the potential mediating effect of self-efficacy, a sense of agency in life, in the relationship between SBP and mental health (wellbeing and illbeing) in teens. Self efficacy has been linked to wellbeing and strengths processes in past studies and is classed as a basic human need and form of eudaimonic happiness. This study reconfirmed the adaptive benefits of SBP in a large sample of Australian adolescents ( N = 11,368; 59% male; M age = 14.04, SD age = 1.99) sourced from 28 schools. Using structural equation modeling, SBP significantly and directly predicted higher happiness and lower depression, with direct effects falling into the 85th and 95th percentile of meta-analytically derived individual differences effect sizes. In addition, self-efficacy was a significant partial mediator, accounting for 40.0% of the total effect on happiness and 52.7% of the total effect on distress. Self-efficacy was also a full mediator in the case of anxiety, with a strong indirect effect. Results suggest that building strengths in teens can also build self-efficacy, and given the large effect sizes, that SBP is a promising leverage point for increasing teen wellbeing.

Penetrator strength effect in long-rod critical ricochet angle

International Nuclear Information System (INIS)

Daneshjou, K.; Shahravi, M.

2008-01-01

3D numerical simulations were performed in order to further investigate the role of penetrator strength in the interaction of long-rods and oblique targets. Three distinctive regimes resulting from oblique impact depending on the obliquity, namely simple ricochet, critical ricochet and target perforation, were investigated in detail. Critical ricochet angles were calculated with a full 3D explicit finite element method for various impact velocities and strength of target plates and projectiles. Numerical predictions were compared with existing two-dimensional analytical models and test results. It was predicted that critical ricochet angle increases with decreasing impact velocity and that higher ricochet angles were expected if higher strength target materials are employed. But there are differences between analytical models and 3D numerical simulation results or test results. The causes for these discrepancies are established by numerical simulations which explore the validity of the penetrator strength parameter in the analytical model as a physical entity. As a matter of fact, in this paper we first investigate the role of penetrator dynamic strength using two-dimensional simulation which resulted in different penetrator strengths out of different impact velocities. Next, by applying these amounts for penetrator strength in Rosenberg analytical model the critical ricochet angle is calculated. Finally, a comparison between the present analytical method with the 3D simulation and test results shows that the new analytical approach leads to modified results with respect to Rosenberg ones

Effect of humidity and interlayer cation on frictional strength of montmorillonite

Science.gov (United States)

Tetsuka, H.; Katayama, I.; Sakuma, H.; Tamura, K.

2016-12-01

Smectite has been ubiquitously seen in fault gouge (Schleicher et al., 2006; Kuo et al., 2009; Si et al., 2014; Kameda, 2015) and is characteristic by low frictional coefficient (Saffer et al., 2001; Ikari et al., 2007); consequently, it has a key role in fault dynamics. The frictional strength of montmorillonite (a typical type of smectite) is affected by mainly two factors, 1) hydration state and 2) interlayer cation. Previous laboratory experiments have shown that the frictional strength of montmorillonite changes with hydration state (Ikari et al., 2007) and with interlayer cation (Behnsen and Faulkner, 2013). However, experimental study for frictional strengths of interlayer cation-exchanged montmorillonite under controlled hydration state has not been reported. We are developing humidity control system in biaxial friction testing machine and try to investigate the effect of relative humidity and interlayer cation on frictional strength of montmorillonite. The humidity control system consists of two units, 1) the pressure vessel (core holder) unit controlled by a constant temperature and 2) the vapor generating unit controlled by variable temperature. We control relative humidity around sample, which is calculated from the temperature around sample and the vapor pressure at vapor generating unit. Preliminary experiments under controlled humidity show frictional coefficient of montmorillonite decrease with increasing relative humidity. In the meeting, we will report the systematic study of frictional coefficient as function of relative humidity and interlayer cation species.

Effect of presaturation and seawater on strength and durability of lightweight concrete

International Nuclear Information System (INIS)

Haque, M.N.

2009-01-01

The internal curing is provided, usually, by the use of some proprietary fine aggregates which provide sufficient water from within to promote the ongoing hydration of cement and hence result in a relatively high performance concrete. Two concretes, one total lightweight concrete (TLWC) and the second sand lightweight concrete (SLWC) of 28 day cube strength of approximately 40 MPa (5800 psi) were designed. A total of six mixes were cast out of these two concretes, 4-TLWC's and 2-SLWC's. The variation in the mixes was due to moisture condition of the aggregates and the use of seawater in mixing and curing of the concretes. The effect of these variations on the cube compressive strength, water permeability, sulphate and chloride content, depth of carbonation and shrinkage of these six concretes was studied. The presaturation of the lightweight aggregates (LWA's used do not seem to have improved the compressive strength, and water permeability of these concretes. The drying shrinkage strains of the concrete using pre saturated aggregates decreased considerably. The application of seawater in making and curing these LWC's increased the compressive strength by about 15%. (author)

Effect of ionic strength on the kinetics of ionic and micellar reactions in aqueous solution

International Nuclear Information System (INIS)

Dung, M.H.; Kozak, J.J.

1982-01-01

The effect of electrostatic forces on the rate of reaction between ions in aqueous solutions of intermediate ionic strength is studied in this paper. We consider the kinetics of reactions involving simple ionic species (1--1 and 2--2 electrolyte systems) as well as kinetic processes mediated by the presence of micellar ions (or other charged organizates). In the regime of ionic strength considered, dielectric saturation of the solvent in the vicinity of the reacting ions must be taken into account and this is done by introducing several models to describe the recovery of the solvent from saturation to its continuum dielectric behavior. To explore the effects of ion size, charge number, and ionic strength on the overall rate constant for the process considered, we couple the traditional theory of ionic reactions in aqueous solution with calculations of the electrostatic potential obtained via solution of the nonlinear Poisson--Boltzmann equation. The great flexibility of the nonlinear Poisson--Boltzmann theory allows us to explore quantitatively the influence of each of these effects, and our simulations show that the short-range properties of the electrostatic potential affect primarily kinetically controlled processes (to varying degrees, depending on the ionic system considered) whereas the down-range properties of the potential play a (somewhat) greater role in influencing diffusion-controlled processes. A detailed examination is made of ionic strength effects over a broad range of ionic concentrations. In the regime of low ionic strength, the limiting slope and intercept of the curve describing the dependence of log k/sub D/ on I/sup 1/2//(1+I/sup 1/2/) may differ considerably from the usual Debye--Hueckel limiting relations, depending on the particular model chosen to describe local saturation effects

Effects of Kettlebell Swing vs. Explosive Deadlift Training on Strength and Power

Directory of Open Access Journals (Sweden)

Matthew R. Maulit

2017-01-01

Full Text Available Background: Recent research has compared explosive deadlift to kettlebell training observing their effects on strength. The kettlebell swing is a popular practical exercise as it shares share a hip hinge movement with the explosive deadlift, but the two have not been compared. Objectives: The purpose of this study was to compare the effects of kettlebell swing vs. explosive deadlift training on strength and power. Methods: Thirty-one recreationally resistance-trained men (age = 23.1 ± 2.3 years, height = 175.5 ± 6.6 cm, mass = 83.9 ± 13.8 kg, 1RM deadlift = 159.9 ± 31.7 kg were randomly assigned to one of two groups [kettlebell swing group (KBG n = 15, or explosive deadlift group (EDLG n = 16]. Vertical jump height, isometric mid-thigh pull (MTP, and 1RM deadlift were measured pre and post training. Both groups trained twice per week for 4 weeks. Volume and load were increased after the first 2 weeks of training. Results: A 2 (time x 2 (group mixed factor ANOVA revealed a significant (P<0.05 increase in deadlift 1RM (pre: 159.9 ± 31.7 kg, post: 168.9 ± 31.8 kg and vertical jump height (pre: 56.6 ± 9.9 cm, post: 57.9 ± 9.7 cm for both groups, but were not significantly different between groups. There were no significant changes in MTP. Conclusions: Strength and conditioning professionals may use both kettlebell swings and explosive deadlifts to increase deadlift strength and vertical jump power.

Effect of Acidic Water on Strength, Durability and Corrosion of ...

African Journals Online (AJOL)

In this study, specimens of 108 cubes (150 mm x 150 mm x 150 mm), 36 cylinders (300 mm x 150 mm), and 72 cylinders (102 mm x 51 mm) were cast and cured in percentages of NaCl added water to find the workability, strength, durability and corrosion resistance characteristics concrete. The effect of corrosion of steel in ...

Heat treatment effect on impact strength of 40Kh steel

International Nuclear Information System (INIS)

Golubev, V.K.; Novikov, S.A.; Sobolev, Yu.S.; Yukina, N.A.

1984-01-01

The paper presents results of studies on the effect of heat treatment on strength and pattern of 40Kh steel impact failure. Loading levels corresponding to macroscopic spalling microdamage initiation in the material are determined for three initial states. Metallographic study on the spalling failure pattern for 40Kh steel in different initial states and data on microhardness measurement are presented

Interactive effects of music tempi and intensities on grip strength and subjective affect.

Science.gov (United States)

Karageorghis, C I; Cheek, P; Simpson, S D; Bigliassi, M

2018-03-01

Pretask music is widely used by athletes albeit there is scant empirical evidence to support its use. The present study extended a line of work into pretask music by examining the interactive effects of music tempo and intensity (volume) on the performance of a simple motor skill and subjective affect. A 2 × 2 within-subjects factorial design was employed with an additional no-music control, the scores from which were used as a covariate. A sample of 52 male athletes (M age  = 26.1 ± 4.8 years) was exposed to five conditions: fast/loud (126 bpm/80 dBA), fast/quiet (126 bpm/70 dBA), slow/loud (87 bpm/80 dBA), slow/quiet (87 bpm/70 dBA) music, and a no-music control. Dependent variables were grip strength, measured with a handgrip dynamometer, and subjective affect, assessed by use of the Affect Grid. The tempo and intensity components of music had interactive effects for grip strength but only main effects for subjective affect. Fast-tempo music played at a high intensity yielded the highest grip strength, while fast-tempo music played at a low-intensity resulted in much lower grip strength (M diff.  = -1.11 Force kg). For affective valence, there were main effects of tempo and intensity, with fast and loud music yielding the highest scores. For affective arousal, there was no difference between tempi although there was between intensities, with the high-intensity condition yielding higher scores. The present findings indicate the utility of fast/loud pretask music in enhancing affective valence and arousal in preparation for a simple or gross motor task. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Acute effect of caffeine supplementation on performance of muscular strength and cardiovascular changes during resistance training

Directory of Open Access Journals (Sweden)

W. Materko

2011-01-01

Full Text Available The purpose of the present study was to evaluate the acute effect of caffeine on the muscular strength performance in addition to the possible hemodynamic changes during a strength training session. Thirteen strength training experienced male subjects were submitted to a protocol of three sets of 10RM for bench press (BP, pull press (PP, leg extension (LE and leg curl (LC, according to three conditions: no supplementation (C; 250 mg of caffeine supplementation (S; placebo (P. All subjects were submitted to an anthropometric evaluation, followed by a 10RM familiarization test. Hemodynamic measurements – heart rate (HR and blood pressure (BP – were carried out before, during and after each session. Holding 48 hours time intervals, participants were submitted to three randomly presented 10RM tests according to C, S and P conditions. For conditions S and C, significant differences were found in BP and LE. No significant differences in HR and BP were found. Results seem to suggest an ergogenic effect of caffeine on submaximal muscle strength during a session of strength training.

Effect of isothermal annealing on the compressive strength of a ZrAlNiCuNb metallic glass

International Nuclear Information System (INIS)

Song Min; He Yuehui

2011-01-01

Research highlights: → Only structural relaxation happens during annealing at the temperature below T g . → Nanocrystallization happens during annealing at the temperature above T g . → The compressive strength increases with annealing time up to 20 min. → The compressive strength decreases with annealing time after 20 min. - Abstract: The effects of isothermal annealing on the microstructures and compressive strength of a Zr 56 Al 10.9 Ni 4.6 Cu 27.8 Nb 0.7 bulk metallic glass (BMG) have been studied using X-ray diffraction, scanning electron microscopy and compression tests. It has been shown that only structural relaxation happens during annealing at the temperature below T g (glass transition temperature), while both structural relaxation and nanocrystallization happen during annealing at the temperature above T g . Compression tests indicated that the strength of the BMG increases with annealing time at 437 deg. C up to 20 min, after which the strength starts to decrease. The strength evolution of the BMG with the annealing time is due to combined effects of the variations of the free volume and nanocrystals.

The effects of surface finish and grain size on the strength of sintered silicon carbide

Science.gov (United States)

You, Y. H.; Kim, Y. W.; Lee, J. G.; Kim, C. H.

1985-01-01

The effects of surface treatment and microstructure, especially abnormal grain growth, on the strength of sintered SiC were studied. The surfaces of sintered SiC were treated with 400, 800 and 1200 grit diamond wheels. Grain growth was induced by increasing the sintering times at 2050 C. The beta to alpha transformation occurred during the sintering of beta-phase starting materials and was often accompanied by abnormal grain growth. The overall strength distributions were established using Weibull statistics. The strength of the sintered SiC is limited by extrinsic surface flaws in normal-sintered specimens. The finer the surface finish and grain size, the higher the strength. But the strength of abnormal sintering specimens is limited by the abnormally grown large tabular grains. The Weibull modulus increases with decreasing grain size and decreasing grit size for grinding.

Effect of grape seed extract against biodegradation of composite resin-dentin shear bond strength

Science.gov (United States)

Generosa, D. M.; Suprastiwi, E.; Asrianti, D.

2017-08-01

This study aimed to analyze the effect of grape seed extract (GSE) on resin-dentin shear bond strength. A group of 48 dentin samples were divided into 6 groups. The six groups, each with eight specimens, included group 1 (control), group 2 (control + NaOCl 10%), group 3 (2.9% GSE application before etching), group 4 (2.9% GSE application before etching + NaOCl 10%), group 5 (2.9% GSE application after etching), and group 6 (2.9% GSE application after etching + NaOCl 10%). Shear bond strengths were measured using a universal testing machine. Statistical analysis was done with the Kruskal-Wallis test and the Mann-Whitney U test. The highest median value was in group 3, and the lowest value was in group 5. GSE can improve the shear bond strength (p = 0.002 and 0.001), but it has no effect on reducing biodegradation (p = 0.141).

Strength Calculation of Locally Loaded Orthotropic Shells

Directory of Open Access Journals (Sweden)

Yu. I. Vinogradov

2015-01-01

Full Text Available The article studies laminated orthotropic cylindrical, conic, spherical, and toroidal shells, which are often locally loaded in the aircraft designs over small areas of their surfaces.The aim of this work is to determine stress concentration in shells versus structure of orthotropic composite material, shell form and parameters, forms of loading areas, which borders do not coincide with lines of main curvatures of shells. For this purpose, an analytical computing algorithm to estimate strength of shells in terms of stress is developed. It enables us to have solution results of the boundary value problem with a controlled error. To solve differential equations an analytical method is used. An algorithm of the boundary value problem solution is multiplicative.The main results of researches are graphs of stress concentration in the orthotropic shells versus their parameters and areas of loading lineated by circles and ellipses.Among the other works aimed at determination of stress concentration in shells, the place of this one is defined by the analytical solution of applied problems for strength estimation in terms of shell stresses of classical forms.The developed effective analytical algorithm to solve the boundary value problem and received results are useful in research and development.

Effect of silver nanoparticles on human mesenchymal stem cell differentiation

Directory of Open Access Journals (Sweden)

Christina Sengstock

2014-11-01

Full Text Available Background: Silver nanoparticles (Ag-NP are one of the fastest growing products in nano-medicine due to their enhanced antibacterial activity at the nanoscale level. In biomedicine, hundreds of products have been coated with Ag-NP. For example, various medical devices include silver, such as surgical instruments, bone implants and wound dressings. After the degradation of these materials, or depending on the coating technique, silver in nanoparticle or ion form can be released and may come into close contact with tissues and cells. Despite incorporation of Ag-NP as an antibacterial agent in different products, the toxicological and biological effects of silver in the human body after long-term and low-concentration exposure are not well understood. In the current study, we investigated the effects of both ionic and nanoparticulate silver on the differentiation of human mesenchymal stem cells (hMSCs into adipogenic, osteogenic and chondrogenic lineages and on the secretion of the respective differentiation markers adiponectin, osteocalcin and aggrecan.Results: As shown through laser scanning microscopy, Ag-NP with a size of 80 nm (hydrodynamic diameter were taken up into hMSCs as nanoparticulate material. After 24 h of incubation, these Ag-NP were mainly found in the endo-lysosomal cell compartment as agglomerated material. Cytotoxicity was observed for differentiated or undifferentiated hMSCs treated with high silver concentrations (≥20 µg·mL−1 Ag-NP; ≥1.5 µg·mL−1 Ag+ ions but not with low-concentration treatments (≤10 µg·mL−1 Ag-NP; ≤1.0 µg·mL−1 Ag+ ions. Subtoxic concentrations of Ag-NP and Ag+ ions impaired the adipogenic and osteogenic differentiation of hMSCs in a concentration-dependent manner, whereas chondrogenic differentiation was unaffected after 21 d of incubation. In contrast to aggrecan, the inhibitory effect of adipogenic and osteogenic differentiation was confirmed by a decrease in the secretion of

Effects of Pelvic and Core Strength Training on High School Cross-Country Race Times.

Science.gov (United States)

Clark, Anne W; Goedeke, Maggie K; Cunningham, Saengchoy R; Rockwell, Derek E; Lehecka, Bryan J; Manske, Robert C; Smith, Barbara S

2017-08-01

Clark, AW, Goedeke, MK, Cunningham, SR, Rockwell, DE, Lehecka, BJ, Manske, RC, and Smith, BS. Effects of pelvic and core strength training on high school cross-country race times. J Strength Cond Res 31(8): 2289-2295, 2017-There is only limited research examining the effect of pelvic and core strength training on running performance. Pelvic and core muscle fatigue is believed to contribute to excess motion along frontal and transverse planes which decreases efficiency in normal sagittal plane running motions. The purpose of this study was to determine whether adding a 6-week pelvic and core strengthening program resulted in decreased race times in high school cross-country runners. Thirty-five high school cross-country runners (14-19 years old) from 2 high schools were randomly assigned to a strengthening group (experimental) or a nonstrengthening group (control). All participants completed 4 standardized isometric strength tests for hip abductors, adductors, extensors, and core musculature in a test-retest design. The experimental group performed a 6-week pelvic and core strengthening program along with their normal training. Participants in the control group performed their normal training without additional pelvic and core strengthening. Baseline, 3-week, and 6-week race times were collected using a repeated measures design. No significant interaction between experimental and control groups regarding decreasing race times and increasing pelvic and core musculature strength occurred over the 6-week study period. Both groups increased strength and decreased overall race times. Clinically significant findings reveal a 6-week pelvic and core stability strengthening program 3 times a week in addition to coach led team training may help decrease race times.

Magnetic-field-induced dose effects in MR-guided radiotherapy systems: dependence on the magnetic field strength.

Science.gov (United States)

Raaijmakers, A J E; Raaymakers, B W; Lagendijk, J J W

2008-02-21

Several institutes are currently working on the development of a radiotherapy treatment system with online MR imaging (MRI) modality. The main difference between their designs is the magnetic field strength of the MRI system. While we have chosen a 1.5 Tesla (T) magnetic field strength, the Cross Cancer Institute in Edmonton will be using a 0.2 T MRI scanner and the company Viewray aims to use 0.3 T. The magnetic field strength will affect the severity of magnetic field dose effects, such as the electron return effect (ERE): considerable dose increase at tissue air boundaries due to returning electrons. This paper has investigated how the ERE dose increase depends on the magnetic field strength. Therefore, four situations where the ERE occurs have been simulated: ERE at the distal side of the beam, the lateral ERE, ERE in cylindrical air cavities and ERE in the lungs. The magnetic field comparison values were 0.2, 0.75, 1.5 and 3 T. Results show that, in general, magnetic field dose effects are reduced at lower magnetic field strengths. At the distal side, the ERE dose increase is largest for B = 0.75 T and depends on the irradiation field size for B = 0.2 T. The lateral ERE is strongest for B = 3 T but shows no effect for B = 0.2 T. Around cylindrical air cavities, dose inhomogeneities disappear if the radius of the cavity becomes small relative to the in-air radius of the secondary electron trajectories. At larger cavities (r > 1 cm), dose inhomogeneities exist for all magnetic field strengths. In water-lung-water phantoms, the ERE dose increase takes place at the water-lung transition and the dose decreases at the lung-water transition, but these effects are minimal for B = 0.2 T. These results will contribute to evaluating the trade-off between magnetic field dose effects and image quality of MR-guided radiotherapy systems.

Magnetic-field-induced dose effects in MR-guided radiotherapy systems: dependence on the magnetic field strength

International Nuclear Information System (INIS)

Raaijmakers, A J E; Raaymakers, B W; Lagendijk, J J W

2008-01-01

Several institutes are currently working on the development of a radiotherapy treatment system with online MR imaging (MRI) modality. The main difference between their designs is the magnetic field strength of the MRI system. While we have chosen a 1.5 Tesla (T) magnetic field strength, the Cross Cancer Institute in Edmonton will be using a 0.2 T MRI scanner and the company Viewray aims to use 0.3 T. The magnetic field strength will affect the severity of magnetic field dose effects, such as the electron return effect (ERE): considerable dose increase at tissue air boundaries due to returning electrons. This paper has investigated how the ERE dose increase depends on the magnetic field strength. Therefore, four situations where the ERE occurs have been simulated: ERE at the distal side of the beam, the lateral ERE, ERE in cylindrical air cavities and ERE in the lungs. The magnetic field comparison values were 0.2, 0.75, 1.5 and 3 T. Results show that, in general, magnetic field dose effects are reduced at lower magnetic field strengths. At the distal side, the ERE dose increase is largest for B = 0.75 T and depends on the irradiation field size for B = 0.2 T. The lateral ERE is strongest for B = 3 T but shows no effect for B = 0.2 T. Around cylindrical air cavities, dose inhomogeneities disappear if the radius of the cavity becomes small relative to the in-air radius of the secondary electron trajectories. At larger cavities (r > 1 cm), dose inhomogeneities exist for all magnetic field strengths. In water-lung-water phantoms, the ERE dose increase takes place at the water-lung transition and the dose decreases at the lung-water transition, but these effects are minimal for B = 0.2 T. These results will contribute to evaluating the trade-off between magnetic field dose effects and image quality of MR-guided radiotherapy systems

Effect of internal stress on the strength of PZT ceramics

Energy Technology Data Exchange (ETDEWEB)

Tai, Weon Pil; Yun, Yeo Bum; Kim, Song Hee [Kangwon National Univ., Chunchon (Korea, Republic of)

1996-01-01

The aim of this study is to investigate the change of bending strength and fatigue strength in the unpolled and poled Pb(Zr, Ti)O ferroelectrics of tetragonal, morphotropic phase boundary (MPB) and rhombohedral composition in terms of internal stress which is measured by XRD method. Before poling treatment the highest bending strength was found in rhombohedral composition. After poling treatment, the bending strength decreased in all compositions but it decreased most remarkably in tetragonal composition. The most prominent decrease of bending strength after poling treatment in tetragonal was attributed to the occurrence of microcracks due to high anisotropic internal stress around grain boundary which was induced by domain alignment toward electric field direction in the microstructure having tetragonality. The decrease of bending strength after poling in MPB and rhombohedral composition was not due to the occurrence of microcracks but to the increase in tensile internal stress perpendicular to the direction of crack propagation by domain alignment. Fatigue strength was higher before poling treatment than after poling treatment for various compositions. 13 refs., 2 tabs., 5 figs.

EFFECTS OF WHOLE BODY VIBRATION ON STRENGTH AND JUMPING PERFORMANCE IN VOLLEYBALL AND BEACH VOLLEYBALL PLAYERS

Science.gov (United States)

Zmijewski, P.; Jimenez-Olmedo, J.M.; Jové-Tossi, M.A.; Martínez-Carbonell, A.; Suárez-Llorca, C.; Andreu-Cabrera, E.

2014-01-01

The primary aim of this study was to examine the effects of 6-week strength training with whole body vibration (WBV) on leg strength and jumping performance in volleyball and beach volleyball players. Twenty-three sub-elite male volleyball (VB; n=12) and beach volleyball players (BVB; n=11) aged 21.2±3.0 years were divided into two groups and subjected to 6 weeks of strength training (three one-hour sessions per week): (I) 12 players (6 VB and 6 BVB players) underwent training with WBV (30-40 Hz, 1.7-2.5 mm, 3.0-5.7 g), and (II) 11 players (6 VB and 5 BVB players) underwent traditional strength training. Squat jump (SJ) and countermovement squat jump (CMJ) measurements by the Ergo Tester contact platform and maximum leg press test (1RM) were conducted. Three-factor (2 time x 2 WBV use x 2 discipline) analysis of variance for SJ, CMJ and 1RM revealed a significant time main effect (pvolleyball and beach volleyball players increases leg strength more and leads to greater improvement in jump performance than traditional strength training, but greater improvements can be expected in beach volleyball players than in volleyball players. PMID:25187676

А new factor effecting gel strength of pectin polysaccharides

Directory of Open Access Journals (Sweden)

S. E. Kholov

2016-01-01

Full Text Available Pectin polysaccharides obtained from various raw materials have a different component composition and form gels with water, sugar and acid or calcium. In this study, an experimental approach the gelation properties of different pectin samples, varied from different sources, using new methods of hydrolysis and purification. Samples were obtained by hydrolysis of accelerated extraction of pectin and purified by diaultrfiltration, have a high gel strength. The highest gel strength have been found in series of high methoxyl (HM- pectin samples of apple, peach, orange and low methoxyl (LM- pectin samples of commercial citrus pectin and apple pectin obtained by new method. It is shown that in addition to the basic parameters (the content of galacturonic acid, degree of esterification, molecular weight and hidrodinamic radius macromolecule to affect gel strength pectins aggregation of macromolecules, which is determined by the z-average molecular weight. There were observed a clear pattern of the influence of the molecular weight on hydrodynamic parameters for both HM- and LM- pectin samples on the gel strength. It were shown that a high values of molecular weight, intrinsic viscosity, and radius of gyration of pectin samples can significantly increase gel strength, while the value of Mz oppositely influenced the gel strength. As a result, a systematic analysis of this parameter and its relationship to the average molecular weight found that indeed the ratio Mz/Mw for pectin’s is an crucial to assess the quality of pectin at the study of gel strength for pectin polysaccharides.

Effects of age, gender and educational background on strength of motivation for medical school.

Science.gov (United States)

Kusurkar, Rashmi; Kruitwagen, Cas; ten Cate, Olle; Croiset, Gerda

2010-08-01

The aim of this study was to determine the effects of selection, educational background, age and gender on strength of motivation to attend and pursue medical school. Graduate entry (GE) medical students (having Bachelor's degree in Life Sciences or related field) and Non-Graduate Entry (NGE) medical students (having only completed high school), were asked to fill out the Strength of Motivation for Medical School (SMMS) questionnaire at the start of medical school. The questionnaire measures the willingness of the medical students to pursue medical education even in the face of difficulty and sacrifice. GE students (59.64 ± 7.30) had higher strength of motivation as compared to NGE students (55.26 ± 8.33), so did females (57.05 ± 8.28) as compared to males (54.30 ± 8.08). 7.9% of the variance in the SMMS scores could be explained with the help of a linear regression model with age, gender and educational background/selection as predictor variables. Age was the single largest predictor. Maturity, taking developmental differences between sexes into account, was used as a predictor to correct for differences in the maturation of males and females. Still, the gender differences prevailed, though they were reduced. Pre-entrance educational background and selection also predicted the strength of motivation, but the effect of the two was confounded. Strength of motivation appears to be a dynamic entity, changing primarily with age and maturity and to a small extent with gender and experience.

[Effects of education and strength training on functional tests among older people with osteoarthritis].

Science.gov (United States)

Jiménez S, Christian Edgardo; Fernández G, Rubén; Zurita O, Félix; Linares G, Daniel; Farías M, Ariel

2014-04-01

Hip and knee osteoarthritis are important causes of pain and disability among older people. Education and strength training can alleviate symptoms and avoid functional deterioration. To assess muscle strength, fall risk and quality of life of older people with osteoarthritis and the effects of physiotherapy education and strength training on these variables. Thirty participants aged 78 ± 5 years (63% women) were randomly assigned to receive physiotherapy (Controls), physiotherapy plus education (Group 1) and physiotherapy plus strength training (group 2). At baseline and after 16 weeks of intervention, patients were evaluated with the Senior Fitness Test, Timed Up and Go and Quality of Life score short form (SF-36). During the intervention period, Senior Fitness Test and Timed Up and Go scores improved in all groups and SF-36 did not change. The improvement in Senior Fitness Test and Timed Up and Go was more marked in Groups 1 and 2 than in the control group. Education and strength training improve functional tests among older people with osteoarthritis.

The effect of growth hormone (GH) replacement on muscle strength in patients with GH-deficiency: a meta-analysis.

LENUS (Irish Health Repository)

Widdowson, W Matthew

2012-02-01

CONTEXT\\/OBJECTIVES: GH replacement increases muscle mass and reduces body fat in growth hormone deficiency (GHD) adults. A recent meta-analysis has demonstrated that this improvement in body composition is associated with improved exercise performance. The current meta-analysis was carried out to determine whether high-quality evidence exists to support a beneficial effect of GH replacement on strength. DESIGN\\/METHODS: An extensive Medline search\\/literature review identified eight studies with utilizable, robust data, involving 231 patients in nine cohorts. Previously unpublished data were sought from authors and obtained in two cases. All studies included were randomized, double-blind, placebo-controlled, of parallel or cross-over design and of an average 6.7 months duration. Information was retrieved in uniform format, with data pertaining to patient numbers, study-design, GH-dose, mean age, IGF-I levels and muscle strength measurements (isometric or isokinetic quadriceps strength) recorded. Data were analysed using a fixed-effects model, utilizing continuous data measured on different scales. A summary effect measure (d(s)) was derived for individual strength variables, whereas an overall summary effect was derived from the sum of all studies incorporating different variables; 95% CIs were calculated from the weighted variances of individual study effects. RESULTS: Analysis revealed no significant improvement, neither when all studies were combined (d(s) = +0.01 +\\/- 0.26) nor when measured individually (isometric quadriceps strength, d(s) = +0.02 +\\/- 0.32 and isokinetic quadriceps strength, d(s) = 0.00 +\\/- 0.45). CONCLUSIONS: Evidence from short-term controlled studies fails to support a benefit on muscle strength of GH replacement in GHD patients, which is likely to occur over a longer time-course, as seen in open-label studies.

Effect of Silica Fume on two-stage Concrete Strength

Science.gov (United States)

Abdelgader, H. S.; El-Baden, A. S.

2015-11-01

Two-stage concrete (TSC) is an innovative concrete that does not require vibration for placing and compaction. TSC is a simple concept; it is made using the same basic constituents as traditional concrete: cement, coarse aggregate, sand and water as well as mineral and chemical admixtures. As its name suggests, it is produced through a two-stage process. Firstly washed coarse aggregate is placed into the formwork in-situ. Later a specifically designed self compacting grout is introduced into the form from the lowest point under gravity pressure to fill the voids, cementing the aggregate into a monolith. The hardened concrete is dense, homogeneous and has in general improved engineering properties and durability. This paper presents the results from a research work attempt to study the effect of silica fume (SF) and superplasticizers admixtures (SP) on compressive and tensile strength of TSC using various combinations of water to cement ratio (w/c) and cement to sand ratio (c/s). Thirty six concrete mixes with different grout constituents were tested. From each mix twenty four standard cylinder samples of size (150mm×300mm) of concrete containing crushed aggregate were produced. The tested samples were made from combinations of w/c equal to: 0.45, 0.55 and 0.85, and three c/s of values: 0.5, 1 and 1.5. Silica fume was added at a dosage of 6% of weight of cement, while superplasticizer was added at a dosage of 2% of cement weight. Results indicated that both tensile and compressive strength of TSC can be statistically derived as a function of w/c and c/s with good correlation coefficients. The basic principle of traditional concrete, which says that an increase in water/cement ratio will lead to a reduction in compressive strength, was shown to hold true for TSC specimens tested. Using a combination of both silica fume and superplasticisers caused a significant increase in strength relative to control mixes.

Effect of Boron on the Strength and Toughness of Direct-Quenched Low-Carbon Niobium Bearing Ultra-High-Strength Martensitic Steel

Science.gov (United States)

Hannula, Jaakko; Kömi, Jukka; Porter, David A.; Somani, Mahesh C.; Kaijalainen, Antti; Suikkanen, Pasi; Yang, Jer-Ren; Tsai, Shao-Pu

2017-11-01

The effect of boron on the microstructures and mechanical properties of laboratory-control-rolled and direct-quenched 6-mm-thick steels containing 0.08 wt pct C and 0.02 wt pct Nb were studied. The boron contents were 24 ppm and a residual amount of 4 ppm. Two different finish rolling temperatures (FRTs) of 1093 K and 1193 K (820 °C and 920 °C) were used in the hot rolling trials to obtain different levels of pancaked austenite prior to DQ. Continuous cooling transformation (CCT) diagrams were constructed to reveal the effect of boron on the transformation behavior of these steels. Microstructural characterization was carried out using various microscopy techniques, such as light optical microscopy (LOM) and scanning electron microscopy-electron backscatter diffraction (SEM-EBSD). The resultant microstructures after hot rolling were mixtures of autotempered martensite and lower bainite (LB), having yield strengths in the range 918 to 1067 MPa with total elongations to fracture higher than 10 pct. The lower FRT of 1093 K (820 °C) produced better combinations of strength and toughness as a consequence of a higher degree of pancaking in the austenite. Removal of boron lowered the 34 J/cm2 Charpy-V impact toughness transition temperature from 206 K to 158 K (-67 °C to -115 °C) when the finishing rolling temperature of 1093 K (820 °C) was used without any loss in the strength values compared to the boron-bearing steel. This was due to the finer and more uniform grain structure in the boron-free steel. Contrary to expectations, the difference was not caused by the formation of borocarbide precipitates, as verified by transmission electron microscopy (TEM) investigations, but through the grain coarsening effect of boron.

Effects of wood fiber surface chemistry on strength of wood–plastic composites

Energy Technology Data Exchange (ETDEWEB)

Migneault, Sébastien, E-mail: sebastien.migneault@uqat.ca [University of Quebec in Abitibi-Temiscamingue (UQAT), 445 boulevard de l’Université, Rouyn-Noranda, Québec J9X 5E4 (Canada); Koubaa, Ahmed, E-mail: ahmed.koubaa@uqat.ca [UQAT (Canada); Perré, Patrick, E-mail: patrick.perre@ecp.fr [École centrale de Paris, Grande Voie des Vignes, F-92 295 Chatenay-Malabry Cedex (France); Riedl, Bernard, E-mail: Bernard.Riedl@sbf.ulaval.ca [Université Laval, 2425 rue de la Terrasse, Québec City, Québec G1V 0A6 (Canada)

2015-07-15

Highlights: • Infrared spectroscopy and X-ray photoelectron spectroscopy analyses showed variations of surface chemical characteristics according to fiber origin. • Surface chemical characteristics of fibers could partly explain the differences in mechanical properties of the wood–plastic composites. • Fibers with carbohydrate rich surface led to stronger wood–plastic composites because the coupling between the matrix and fibers using coupling agent is achieved with polar sites mostly available on carbohydrates. • Conversely, lignin or extractives rich surface do not have oxidized functions for the esterification reaction with coupling agent and thus led to wood–plastic composites with lower mechanical properties. • Other factors such as mechanical interlocking and fiber morphology interfere with the effects of fiber surface chemistry. - Abstract: Because wood–plastic composites (WPC) strength relies on fiber-matrix interaction at fiber surface, it is likely that fiber surface chemistry plays an important role in WPC strength development. The objective of the present study is to investigate the relationships between fiber surface chemical characteristics and WPC mechanical properties. Different fibers were selected and characterized for surface chemical characteristics using X-ray photoelectron spectroscopy (XPS) and infrared spectroscopy (FTIR). WPC samples were manufactured at 40% fiber content and with six different fibers. High density polyethylene was used as matrix and maleated polyethylene (MAPE) was used as compatibility agent. WPC samples were tested for mechanical properties and fiber-matrix interface was observed with scanning electron microscope. It was found WPC strength decreases as the amount of unoxidized carbon (assigned to lignin and extractives) measured with XPS on fiber surface increases. In the opposite case, WPC strength increases with increasing level of oxidized carbon (assigned to carbohydrates) on fiber surface. The same

Effects of wood fiber surface chemistry on strength of wood–plastic composites

International Nuclear Information System (INIS)

Migneault, Sébastien; Koubaa, Ahmed; Perré, Patrick; Riedl, Bernard

2015-01-01

Highlights: • Infrared spectroscopy and X-ray photoelectron spectroscopy analyses showed variations of surface chemical characteristics according to fiber origin. • Surface chemical characteristics of fibers could partly explain the differences in mechanical properties of the wood–plastic composites. • Fibers with carbohydrate rich surface led to stronger wood–plastic composites because the coupling between the matrix and fibers using coupling agent is achieved with polar sites mostly available on carbohydrates. • Conversely, lignin or extractives rich surface do not have oxidized functions for the esterification reaction with coupling agent and thus led to wood–plastic composites with lower mechanical properties. • Other factors such as mechanical interlocking and fiber morphology interfere with the effects of fiber surface chemistry. - Abstract: Because wood–plastic composites (WPC) strength relies on fiber-matrix interaction at fiber surface, it is likely that fiber surface chemistry plays an important role in WPC strength development. The objective of the present study is to investigate the relationships between fiber surface chemical characteristics and WPC mechanical properties. Different fibers were selected and characterized for surface chemical characteristics using X-ray photoelectron spectroscopy (XPS) and infrared spectroscopy (FTIR). WPC samples were manufactured at 40% fiber content and with six different fibers. High density polyethylene was used as matrix and maleated polyethylene (MAPE) was used as compatibility agent. WPC samples were tested for mechanical properties and fiber-matrix interface was observed with scanning electron microscope. It was found WPC strength decreases as the amount of unoxidized carbon (assigned to lignin and extractives) measured with XPS on fiber surface increases. In the opposite case, WPC strength increases with increasing level of oxidized carbon (assigned to carbohydrates) on fiber surface. The same

Shear bond strength of orthodontic brackets and disinclusion buttons: effect of water and saliva contamination.

Science.gov (United States)

Sfondrini, Maria Francesca; Fraticelli, Danilo; Gandini, Paola; Scribante, Andrea

2013-01-01

The aim of this study was to assess the effect of water and saliva contamination on the shear bond strength and failure site of orthodontic brackets and lingual buttons. 120 bovine permanent mandibular incisors were randomly divided into 6 groups of 20 specimens each. Both orthodontic brackets and disinclusion buttons were tested under three different enamel surface conditions: (a) dry, (b) water contamination, and (c) saliva contamination. Brackets and buttons were bonded to the teeth and subsequently tested using a Instron universal testing machine. Shear bond strength values and adhesive failure rate were recorded. Statistical analysis was performed using ANOVA and Tukey tests (strength values) and Chi squared test (ARI Scores). Noncontaminated enamel surfaces showed the highest bond strengths for both brackets and buttons. Under water and saliva contamination orthodontic brackets groups showed significantly lower shear strengths than disinclusion buttons groups. Significant differences in debond locations were found among the groups under the various enamel surface conditions. Water and saliva contamination of enamel during the bonding procedure lowers bond strength values, more with orthodontic brackets than with disinclusion buttons.

Effect of Protein Intake on Strength, Body Composition and Endocrine Changes in Strength/Power Athletes

Directory of Open Access Journals (Sweden)

Kang Jie

2006-12-01

Full Text Available Abstract Comparison of protein intakes on strength, body composition and hormonal changes were examined in 23 experienced collegiate strength/power athletes participating in a 12-week resistance training program. Subjects were stratified into three groups depending upon their daily consumption of protein; below recommended levels (BL; 1.0 – 1.4 g·kg-1·day-1; n = 8, recommended levels (RL; 1.6 – 1.8 g·kg-1·day-1; n = 7 and above recommended levels (AL; > 2.0 g·kg-1·day-1; n = 8. Subjects were assessed for strength [one-repetition maximum (1-RM bench press and squat] and body composition. Resting blood samples were analyzed for total testosterone, cortisol, growth hormone, and insulin-like growth factor. No differences were seen in energy intake (3,171 ± 577 kcal between the groups, and the energy intake for all groups were also below the recommended levels for strength/power athletes. No significant changes were seen in body mass, lean body mass or fat mass in any group. Significant improvements in 1-RM bench press and 1-RM squat were seen in all three groups, however no differences between the groups were observed. Subjects in AL experienced a 22% and 42% greater change in Δ 1-RM squat and Δ 1-RM bench press than subjects in RL, however these differences were not significant. No significant changes were seen in any of the resting hormonal concentrations. The results of this study do not provide support for protein intakes greater than recommended levels in collegiate strength/power athletes for body composition improvements, or alterations in resting hormonal concentrations.

Effects of an Eight-Week Stepladder Exercise Protocol on Lower Limb Muscular Strength of Apparently Healthy Young Adults

Directory of Open Access Journals (Sweden)

Olagbegi Oladapo Michael

2017-09-01

Full Text Available Purpose. Backward descent of stairs is associated with improved muscle strength and reduced joint stress, but the effect of backward ascent of stairs on lower limb muscle strength has not been reported. This study compared the effects of forward and backward stair climbing on lower limb muscle strength in apparently healthy young adults. Methods. The total of 31 young volunteers were allocated to either forward or backward stair climbing group (n = 16 and 15, respectively. Dynamic quadriceps and hamstring muscle strength was assessed in addition to thigh girth at baseline and at weeks 4 and 8 with the use of the repetitive maximum method and tape measure, respectively. Results. Between baseline and week 8, muscular strength in both groups (quadriceps: 14.4 ± 3.6 to 16.4 ± 3.4 kg; 14.0 ± 2.9 to 15.3 ± 2.7 kg; hamstring: 12.2 ± 3.2 to 13.4 ± 3.2; 11.7 ± 2.5 to 12.9 ± 2.7 kg increased significantly (p 0.05. The groups were comparable in all three measures post intervention. Conclusions. Forward and backward stair climbing protocols are effective for improving the dynamic strength of the hamstring and quadriceps muscles of apparently healthy young adults. Thus, either protocol could be used for the improvement of lower limbs dynamic muscle strength.

Stimulatory effect of undecylenic acid on mouse osteoblast differentiation.

Science.gov (United States)

Kim, Myung Hee; Shim, Ki Shuk; Lee, Su-Ui; Kim, Young Sup; Min, Yong Ki; Kim, Seong Hwan

2010-04-01

Natural compounds with bone-forming (or anabolic) activity have been recently focused on in bone research. The present study investigated the effect of undecylenic acid (UA) on osteoblast differentiation in mouse osteoblastic MC3T3-E1 subclone 4 cells and primary mouse calvarial cells. Low concentrations of UA (up to 5 microM) exhibited no cytotoxicity and significantly increased the expression and activity of alkaline phosphatase (early differentiation marker of osteoblast) and calcium deposition with the induction of expression of the osteocalcin gene in both cells. Interestingly, at low concentration of UA, the induction of NF-kappaB p65 translocation into nucleus and the up-regulation of AP-1 and NFATc1 transcript levels were also observed, suggesting that the stimulatory effect of UA on osteoblast differentiation could be mediated through the activation of transcription factors. Additionally, although the patterns of UA-induced activation of MAP kinases (JNK and p38) were not completely consistent with the increase of both ALP activity and calcium deposition by UA, MAP kinases might be partially involved in the biological function of UA during the early and late stages of osteoblast differentiation. Copyright (c) 2009 John Wiley & Sons, Ltd.

Effects of densified silica fume on microstructure and compressive strength of blended cement pastes

International Nuclear Information System (INIS)

Ji Yajun; Cahyadi, Jong Herman

2003-01-01

Some experimental investigations on the microstructure and compressive strength development of silica fume blended cement pastes are presented in this paper. The silica fume replacement varies from 0% to 20% by weight and the water/binder ratio (w/b) is 0.4. The pore structure by mercury intrusion porosimetry (MIP), the micromorphology by scanning electron microscopy (SEM) and the compressive strength at 3, 7, 14, 28, 56 and 90 days have been studied. The test results indicate that the improvements on both microstructure and mechanical properties of hardened cement pastes by silica fume replacement are not effective due to the agglomeration of silica fume particles. The unreacted silica fume remained in cement pastes, the threshold diameter was not reduced and the increase in compressive strength was insignificant up to 28 days. It is suggested that the proper measures should be taken to disperse silica fume agglomeration to make it more effective on improving the properties of materials

Effect of strength training on regional hypertrophy of the elbow flexor muscles.

Science.gov (United States)

Drummond, Marcos D M; Szmuchrowski, Leszek A; Goulart, Karine N O; Couto, Bruno P

2016-10-01

Muscle hypertrophy is the main structural adaptation to strength training. We investigated the chronic effects of strength training on muscle hypertrophy in different regions of the elbow flexor muscles. Eleven untrained men (21.8 ± 1.62 years) underwent magnetic resonance imaging to determine the proximal, medial, distal, and mean cross-sectional areas (CSA) of the elbow flexors. The volunteers completed 12 weeks of strength training. The training protocol consisted of 4 sets of 8-10 maximum repetitions of unilateral elbow flexion. The interval between sets was 120 s. The training frequency was 3 sessions per week. The magnetic resonance images verified the presence of significant and similar hypertrophy in the distal, medial, and proximal portions of the elbow flexor muscles. Muscle hypertrophy may be assessed using only the medial CSA. We should not expect different degrees of hypertrophy among the regions of the elbow flexor muscles. Muscle Nerve 54: 750-755, 2016. © 2016 Wiley Periodicals, Inc.

Investigation on the Effect of Drained Strength when Designing Sheet Pile Walls

DEFF Research Database (Denmark)

Iversen, Kirsten Malte; Nielsen, Benjaminn Nordahl; Augustesen, Anders Hust

that the height, anchor force, and the maximum bending moment in the wall can be lowered significantly when the effective cohesion is increased above zero. However, as the cohesion increases, the drop in the moment levels off, which implies that the benefit obtained from investigations increasing the cohesion......Long sheet pile walls are constructed in the cities as an integrated part of deep excavations for e.g. parking lots, pumping stations, reservoirs, and cut and cover tunnels. To minimise costs, the strength of the soil needs to be determined in the best possible way. The drained strength of clay...... expressed by c and ϕ is often estimated as c 10% = 10%・cu, and found by estimations based on the soil describtion, respectively. However, due to possible slicken slides and tension cracks, c = 0 is used on the back side of the sheet pile wall. This reduces the strength significantly. A parametric study...

Effect of Soorh Metakaolin on Concrete Compressive Strength and Durability

Directory of Open Access Journals (Sweden)

A. Saand

2017-12-01

Full Text Available Concrete durability is a key aspect for forecasting the expected life time of concrete structures. In this paper, the effect of compressive strength and durability of concrete containing metakaolin developed from a local natural material (Soorh of Thatta Distict of Sindh, Pakistan is investigated. Soorh is calcined by an electric furnace at 8000C for 2 hours to produce metakaolin. One mix of ordinary concrete and five mixes of metakaolin concrete were prepared, where cement is replaced by developed metakaolin from 5% to 25% by weight, with 5% increment step. The concrete durability was tested for water penetration, carbonation depth and corrosion resistance. The obtained outcomes demonstrated that, 15% replacement level of local developed metakaolin presents considerable improvements in concrete properties. Moreover, a considerable linear relationship was established between compressive strength and concrete durability indicators like water penetration, carbonation depth and corrosion resistance.

Effect of Differential Item Functioning on Test Equating

Science.gov (United States)

Kabasakal, Kübra Atalay; Kelecioglu, Hülya

2015-01-01

This study examines the effect of differential item functioning (DIF) items on test equating through multilevel item response models (MIRMs) and traditional IRMs. The performances of three different equating models were investigated under 24 different simulation conditions, and the variables whose effects were examined included sample size, test…

Fissure formation in coke. 2: Effect of heating rate, shrinkage and coke strength

Energy Technology Data Exchange (ETDEWEB)

D.R. Jenkins; M.R. Mahoney [CSIRO, North Ryde, NSW (Australia). Mathematical and Information Sciences

2010-07-15

We investigate the effects of the heating rate, coke shrinkage and coke breakage strength upon the fissure pattern developed in a coke oven charge during carbonisation. This is done principally using a mechanistic model of the formation of fissures, which considers them to be an array of equally spaced fissures, whose depth follows a 'period doubling' pattern based upon the time history of the fissures. The model results are compared with pilot scale coke oven experiments. The results show that the effect of heating rate on the fissure pattern is different to the effect of coke shrinkage, while the effect of coke breakage strength on the pattern is less pronounced. The results can be seen in both the shape and size of resulting coke lumps after stabilisation. The approach gives the opportunity to consider means of controlling the carbonisation process in order to tune the size of the coke lumps produced. 7 refs., 18 figs., 4 tabs.

Effect of shallow angles on compressive strength of biaxial and triaxial laminates.

Science.gov (United States)

Jia, Hongli; Yang, Hyun-Ik

2016-01-01

Biaxial (BX) and triaxial (TX) composite laminates with ±45° angled plies have been widely used in wind turbine blades. As the scale of blades increases, BX and TX laminates with shallow-angled plies (i.e. off-axis ply angle shallow-angled BX and TX laminates are critical considering their locations in a wind turbine blade, and therefore in this study, the uniaxial static compression tests were conducted using BX and TX laminates with angled-plies of ±45°, ±35°, and ±25°, for the purpose of evaluation. On the other hand, Mori-Tanaka mean field homogenization method was employed to predict elastic constants of plies in BX and TX laminates involved in tests; linear regression analyses of experimentally measured ply strengths collected from various sources were then performed to estimate strengths of plies in BX and TX laminates; finally, Tsai-Wu, Hashin, and Puck failure criteria were chosen to predict compressive strengths of BX and TX laminates. Comparison between theoretical predictions and test results were carried out to illustrate the effectiveness of each criterion. The compressive strength of BX laminate decreases as ply angle increases, and the trend was successfully predicted by all three failure criteria. For TX laminates, ±35° angled plies rather than ±45° angled plies led to the lowest laminate compressive strength. Hashin and Puck criteria gave good predictions at certain ply angles for TX laminates, but Tsai-Wu criterion was able to capture the unexpected strength variation of TX laminates with ply angle. It was concluded that the transverse tensile stress in 0° plies of TX laminates, which attains its maximum when the off-axis ply angle is 35°, is the dominant factor in failure determination if using Tsai-Wu criterion. This explains the unexpected strength variation of TX laminates with ply angle, and also indicates that proper selection of ply angle is the key to fully utilizing the advantages of shallow-angled laminates.

Effects of drought stress on seed sink strength and leaf protein ...

African Journals Online (AJOL)

Assimilate availability and the capacity to utilise them in the reproductive structures to a large extent determine reproductive sink establishment and yield of crops under drought stress. This study was carried out to investigate the effect of drought stress imposed at early pod-fill stage on seed sink strength of common bean ...

The effects of strength training on cognitive performance in elderly women.

Science.gov (United States)

Smolarek, André de Camargo; Ferreira, Luis Henrique Boiko; Mascarenhas, Luis Paulo Gomes; McAnulty, Steven R; Varela, Karla Daniele; Dangui, Mônica C; de Barros, Marcelo Paes; Utter, Alan C; Souza-Junior, Tácito P

2016-01-01

Aging is a degenerative process marked by recognized functional, physiological, and metabolic impairments, such as dynapenia and diminished cognitive capacity. Therefore, the search for innovative strategies to prevent/delay these physiological and cognitive disorders is essential to guarantee the independence and life quality of an elderly population. The aim of this work is to verify the effect of a 12-week resistance exercise program on the general physical aptitude and cognitive capacities of elderly and sedentary women. Twenty-nine women (65.87±5.69 years) were divided into two groups. The control group was composed of eight elderly women who met the same inclusion criteria of the study and the strength training group was composed of 29 elderly women who were subjected to a resistance exercise program defined by 12 upper and lower limb exercises combined in 3×10 repetitions with 1-minute interval between repetitions and two resting minutes between exercises (three times/week). Weight loads were fixed between 60% and 75% of the apparent 1 repetition maximum, which was estimated by the test of 10 maximum repetitions. The direct curl was performed for upper body strength evaluation with 2.3 kg dumbbells for 30 seconds, whereas the chair test was used for lower body evaluation (total sit-stand movements in 30 seconds). The cognitive capacities of subjects were evaluated by "The Montreal Cognitive Assessment" questionnaire. After 12 weeks, the elderly group showed significant increases in the average upper body strength (58%), lower body strength (68%), and cognitive capacity (19%). The present study demonstrated that regular resistance exercises could provide significant gains on the upper and lower body strength concomitant to positive improvements on cognitive capacities of elderly women, bringing enhanced life quality.

Analytical Solution of Interface Effect on the Strength of Combined Model Composed of Different Geologic Bodies

Directory of Open Access Journals (Sweden)

Zeng-hui Zhao

2014-01-01

Full Text Available According to the special combined structure of surrounding rock in western mining area of China, a micromechanical model with variable parameters containing contact interface was proposed firstly. Then, the derived stresses in coal and rock near the interface were analyzed on the basis of the harmonized strain relation, and the analytical solutions with respect to stress states near the interface were drawn up. The triaxial compressive strength of coal and rock was further determined in case the contact interface was in the horizontal position. Moreover, effects of stiffness ratio, interface angle, and stress level on the strength of two bodies near the contact area were expounded in detail. Results indicate that additional stresses which have significant effect on the strength of combined model are derived due to the adhesive effect of contact interface and lithological differences between geologic bodies located on both sides. The interface effect on the strength of combined body is most associated with the stiffness, interface angle, and the stress level. These conclusions are also basically valid for three-body model and even for the multibody model and lay important theory foundation to guide the stability study of soft strata composed of different geologic bodies.

Lifting strength in two-person teamwork.

Science.gov (United States)

Lee, Tzu-Hsien

2016-01-01

This study examined the effects of lifting range, hand-to-toe distance, and lifting direction on single-person lifting strengths and two-person teamwork lifting strengths. Six healthy males and seven healthy females participated in this study. Two-person teamwork lifting strengths were examined in both strength-matched and strength-unmatched groups. Our results showed that lifting strength significantly decreased with increasing lifting range or hand-to-toe distance. However, lifting strengths were not affected by lifting direction. Teamwork lifting strength did not conform to the law of additivity for both strength-matched and strength-unmatched groups. In general, teamwork lifting strength was dictated by the weaker of the two members, implying that weaker members might be exposed to a higher potential danger in teamwork exertions. To avoid such overexertion in teamwork, members with significantly different strength ability should not be assigned to the same team.

Effect of gas release in hot molding on flexural strength of composite friction brake

Science.gov (United States)

Rusdja, Andy Permana; Surojo, Eko; Muhayat, Nurul; Raharjo, Wijang Wisnu

2018-02-01

Composite friction brake is a vital part of braking system which serves to reduce the speed of vehicle. To fulfill the requirement of brake performance, composite friction brake must have friction and mechanical characteristic as required. The characteristics of composite friction brake are affected by brake material formulation and manufacturing parameter. In the beginning of hot molding, intermittent hot pressing was carried out to release the gases that consist of ammonia gas and water vapor. In composite friction brake, phenolic resin containing hexamethylenetetramine (HMTA) is often used as a binder. During hot molding, the reaction of phenolic resin and HMTA forms ammonia gas. Hot molding also generates water vapor because raw materials absorb moisture from environment when they are placed in storage. The gas release in hot molding is supposed affecting mechanical properties because it avoid entrapped gas in composite, so that this research investigated effect of gas release on flexural strength. Manufacturing of composite specimen was carried out as follow: mixing of raw materials, cold molding, and hot molding. In this research, duration of intermittent hot pressing and number of gas release were varied. The flexural strength of specimen was measured using three point bending test. The results showed that flexural strength specimens that were manufactured without gas release, using 4 times gas release with intermittent hot pressing for 5 and 10 seconds were not remarkably different. Conversely, hot molding using 4 times gas release with intermittent hot pressing for 15 seconds decreased flexural strength of composite. Hot molding using 2, 4, and 8 times gas release with intermittent hot pressing for 10 seconds also had no effect on increasing flexural strength. Increasing of flexural strength of composite was obtained only by using 6 times gas release with intermittent hot pressing for 10 seconds.

Bonding Strength Effects in Hydro-Mechanical Coupling Transport in Granular Porous Media by Pore-Scale Modeling

Directory of Open Access Journals (Sweden)

Zhiqiang Chen

2016-03-01

Full Text Available The hydro-mechanical coupling transport process of sand production is numerically investigated with special attention paid to the bonding effect between sand grains. By coupling the lattice Boltzmann method (LBM and the discrete element method (DEM, we are able to capture particles movements and fluid flows simultaneously. In order to account for the bonding effects on sand production, a contact bond model is introduced into the LBM-DEM framework. Our simulations first examine the experimental observation of “initial sand production is evoked by localized failure” and then show that the bonding or cement plays an important role in sand production. Lower bonding strength will lead to more sand production than higher bonding strength. It is also found that the influence of flow rate on sand production depends on the bonding strength in cemented granular media, and for low bonding strength sample, the higher the flow rate is, the more severe the erosion found in localized failure zone becomes.

A STUDY OF TRANSVERSE AND LONGITUDINAL SIZE EFFECTS IN HIGH-STRENGTH POLYETHYLENE FIBERS

NARCIS (Netherlands)

PENNING, JP; DEVRIES, AA; PENNINGS, AJ; HOOGSTRATEN, HW

The results of an experimental study of the effects of fibre diameter and testing length on the strength of polyethylene fibres prepared by the gel-spinning-hot-drawing process are reported. These size effects have been studied in fibres covering a range of mechanical properties in order to

Effects of a low-intensity strength-training program on knee-extensor strength and functional ability of frail older people

NARCIS (Netherlands)

Westhoff, M.H.; Stemmerik, L.; Boshuizen, H.C.

2000-01-01

This study's purpose was to investigate whether a 10-week low-intensity strength-training program could improve strength of the knee extensors and functional ability. Participants 65 years and older with low knee-extensor muscle strength were randomized into an exercise (n = 11) and a control group

Effect of Water on Coal Strength | Singh | Momona Ethiopian Journal ...

African Journals Online (AJOL)

Water content is one of the most important factors influencing the rock strength. The present study has been conducted to see how coal strength changes under dry and water saturated conditions. The study reveals that the strength of coal decreases with increasing moisture. For rock mechanics and rock engineering ...

The Effect of Gap Angle on Tensile Strength of Preceramic Base Metal Solder Joints.

Science.gov (United States)

Fattahi, Farnaz; Hashemi Ardakani, Zahra; Hashemi Ardakani, Maryam

2015-12-01

Soldering is a process commonly used in fabricating dental prosthesis. Since most soldered prosthesis fail at the solder joints; the joint strength is of utmost importance. The purpose of this study was to evaluate the effect of gap angle on the tensile strength of base metal solder joints. A total number of 40 Ni-Cr samples were fabricated according to ADA/ISO 9693 specifications for tensile test. Samples were cut at the midpoint of the bar, and were placed at the considered angles by employing an explicitly designed device. They were divided into 4 groups regarding the gap angle; Group C (control group) with parallel gap on steady distance of 0.2mm, Group 1: 10°, Group 2: 20°, and Group3: 30° gap angles. When soldered, the specimens were all tested for tensile strength using a universal testing machine at a cross-head speed of 0.5 mm/min with a preload of 10N. Kruskal-Wallis H test was used to compare tensile strength among the groups (ptensile strength values obtained from the study groups were respectively 307.84, 391.50, 365.18, and 368.86 MPa. The tensile strength was not statistically different among the four groups in general (p≤ 0.490). Making the gap angular at the solder joints and the subsequent unsteady increase of the gap distance would not change the tensile strength of the joint.

Differential effects of strength training and testosterone treatment on soluble CD36 in aging men: Possible relation to changes in body composition

DEFF Research Database (Denmark)

Glintborg, Dorte; Christensen, Louise L; Kvorning, Thue

2015-01-01

Purpose. We measured soluble CD36 (sCD36) and body composition to determine the effects of testosterone treatment (TT) and/or strength training (ST) on cardiovascular risk in men with low normal testosterone levels. Methods. Double-blinded, placebo-controlled study in 54 men aged 60-78 years...... with bioavailable testosterone 94 cm randomized to TT (gel, 50-100 mg/day, n = 20), placebo (n = 18) or ST (n = 16) for 6 months. Moreover, the ST group was randomized to TT (ST + TT, n = 7) or placebo (ST + placebo, n = 9) after 3 months. Outcomes. sCD36, total and regional fat mass were....... units] vs. TT and vs. placebo (p testosterone and lean body mass. Fat mass measures significantly improved during ST + placebo, ST + TT, and TT vs. placebo. During ST + placebo, delta sCD36 was associated with delta total fat mass (r = 0.81) and delta...

Burrowing as a novel voluntary strength training method for mice : A comparison of various voluntary strength or resistance exercise methods

NARCIS (Netherlands)

Roemers, P; Mazzola, P N; De Deyn, P P; Bossers, W J; van Heuvelen, M J G; van der Zee, E A

2018-01-01

BACKGROUND: Voluntary strength training methods for rodents are necessary to investigate the effects of strength training on cognition and the brain. However, few voluntary methods are available. NEW METHOD: The current study tested functional and muscular effects of two novel voluntary strength

EFFECT OF TRAINING WITH NEUROMUSCULAR ELECTRICAL STIMULATION ON ELBOW FLEXION STRENGTH

Directory of Open Access Journals (Sweden)

William R. Holcomb

2006-06-01

Full Text Available Neuromuscular electrical stimulation (NMES may be used to prevent strength loss associated with post-surgical immobilization. Most studies testing the effectiveness of NMES have trained the knee extensors. The purpose of this investigation was to test the effectiveness of NMES when training the elbow flexors. Twenty-four students were randomly assigned to one of three groups: NMES training, isometric training or control. Testing and training were completed using a Biodex™ dynamometer. After a standard warm-up, subjects were positioned on the Biodex™ with left shoulder in anatomical neutral, elbow flexed to 90o and forearm supinated. Subjects performed three maximum isometric contractions of 5 seconds duration, with 1 min rest between repetitions. Average peak torque during three repetitions was calculated. Subjects trained on three days per week for four weeks. Training included 15 maximum contractions of 15 seconds duration with 45 seconds recovery between repetitions. Russian current was delivered by a Forte™ 400 Combo via electrodes placed over ends of biceps brachii. A maximum tolerable ramped intensity was delivered with frequency of 90 bps and duty cycle of 15:45. After training, subjects were post-tested in a manner identical to pretest. Mean normalized strength data were analyzed using a 3 (Group x 2 (Test ANOVA. The Group x Test interaction was significant. Post-hoc analyses revealed that the voluntary training group (normalized means of 0.49 to 0.71 for the pretest and post-test, respectively had a significantly greater increase than the other two groups, which were not significantly different from each other. The lack of significant strength gains with NMES was likely due to low average training intensity, which was only 20.4% of MVIC. Based on these results, NMES training may not be an effective alternative to voluntary training in healthy subjects

Effect of chlorhexidine on the shear bond strength of self-etch ...

African Journals Online (AJOL)

The aim of this study was to investigate the effect of chlorhexidine on shear bond strength of self-etch adhesives to dentin. The crowns of 60 sound human premolars were horizontally sectioned to expose the coronal dentin. Dentin surfaces were polished with 320 grit silicon carbide papers, and were randomly divided into 4 ...

3D printing of high-strength bioscaffolds for the synergistic treatment of bone cancer

Science.gov (United States)

Ma, Hongshi; Li, Tao; Huan, Zhiguang; Zhang, Meng; Yang, Zezheng; Wang, Jinwu; Chang, Jiang; Wu, Chengtie

2018-04-01

The challenges in bone tumor therapy are how to repair the large bone defects induced by surgery and kill all possible residual tumor cells. Compared to cancellous bone defect regeneration, cortical bone defect regeneration has a higher demand for bone substitute materials. To the best of our knowledge, there are currently few bifunctional biomaterials with an ultra-high strength for both tumor therapy and cortical bone regeneration. Here, we designed Fe-CaSiO3 composite scaffolds (30CS) via 3D printing technique. First, the 30CS composite scaffolds possessed a high compressive strength that provided sufficient mechanical support in bone cortical defects; second, synergistic photothermal and ROS therapies achieved an enhanced tumor therapeutic effect in vitro and in vivo. Finally, the presence of CaSiO3 in the composite scaffolds improved the degradation performance, stimulated the proliferation and differentiation of rBMSCs, and further promoted bone formation in vivo. Such 30CS scaffolds with a high compressive strength can function as versatile and efficient biomaterials for the future regeneration of cortical bone defects and the treatment of bone cancer.

Seemingly irrational driving behavior model: The effect of habit strength and anticipated affective reactions.

Science.gov (United States)

Chung, Yi-Shih

2015-09-01

An increasing amount of evidence suggests that aberrant driving behaviors are not entirely rational. On the basis of the dual-process theory, this study postulates that drivers may learn to perform irrational aberrant driving behaviors, and these behaviors could be derived either from a deliberate or an intuitive decision-making approach. Accordingly, a seemingly irrational driving behavior model is proposed; in this model, the theory of planned behavior (TPB) was adopted to represent the deliberate decision-making mechanism, and habit strength was incorporated to reflect the intuitive decision process. A multiple trivariate mediation structure was designed to reflect the process through which driving behaviors are learned. Anticipated affective reactions (AARs) were further included to examine the effect of affect on aberrant driving behaviors. Considering the example of speeding behaviors, this study developed scales and conducted a two-wave survey of students in two departments at a university in Northern Taiwan. The analysis results show that habit strength consists of multiple aspects, and frequency of past behavior cannot be a complete repository for accumulating habit strength. Habit strength appeared to be a crucial mediator between intention antecedents (e.g., attitude) and the intention itself. Including habit strength in the TPB model enhanced the explained variance of speeding intention by 26.7%. In addition, AARs were different from attitudes; particularly, young drivers tended to perform speeding behaviors to reduce negative feelings such as regret. The proposed model provides an effective alternative approach for investigating aberrant driving behaviors; corresponding countermeasures are discussed. Copyright © 2015 Elsevier Ltd. All rights reserved.

The effect of wall thickness distribution on mechanical reliability and strength in unidirectional porous ceramics

Science.gov (United States)

Seuba, Jordi; Deville, Sylvain; Guizard, Christian; Stevenson, Adam J.

2016-01-01

Macroporous ceramics exhibit an intrinsic strength variability caused by the random distribution of defects in their structure. However, the precise role of microstructural features, other than pore volume, on reliability is still unknown. Here, we analyze the applicability of the Weibull analysis to unidirectional macroporous yttria-stabilized-zirconia (YSZ) prepared by ice-templating. First, we performed crush tests on samples with controlled microstructural features with the loading direction parallel to the porosity. The compressive strength data were fitted using two different fitting techniques, ordinary least squares and Bayesian Markov Chain Monte Carlo, to evaluate whether Weibull statistics are an adequate descriptor of the strength distribution. The statistical descriptors indicated that the strength data are well described by the Weibull statistical approach, for both fitting methods used. Furthermore, we assess the effect of different microstructural features (volume, size, densification of the walls, and morphology) on Weibull modulus and strength. We found that the key microstructural parameter controlling reliability is wall thickness. In contrast, pore volume is the main parameter controlling the strength. The highest Weibull modulus (?) and mean strength (198.2 MPa) were obtained for the samples with the smallest and narrowest wall thickness distribution (3.1 ?m) and lower pore volume (54.5%).

Effect of Dentin Wetness on the Bond Strength of Universal Adhesives

Science.gov (United States)

Lee, Ji-Hye; Son, Sung-Ae; Jung, Kyoung-Hwa; Kwon, Yong Hoon

2017-01-01

The effects of dentin wetness on the bond strength and adhesive interface morphology of universal adhesives have been investigated using micro-tensile bond strength (μTBS) testing and confocal laser scanning microscopy (CLSM). Seventy-two human third molars were wet ground to expose flat dentin surfaces. They were divided into three groups according to the air-drying time of the dentin surfaces: 0 (without air drying), 5, and 10 s. The dentin surfaces were then treated with three universal adhesives: G-Premio Bond, Single Bond Universal, and All-Bond Universal in self-etch or etch-and-rinse mode. After composite build up, a μTBS test was performed. One additional tooth was prepared for each group by staining the adhesives with 0.01 wt % of Rhodamine B fluorescent dye for CLSM analysis. The data were analyzed statistically using ANOVA and Tukey’s post hoc tests (α = 0.05). Two-way ANOVA showed significant differences among the adhesive systems and dentin moisture conditions. An interaction effect was also observed (p adhesives. PMID:29068404

Hygrothermal effects on the tensile strength of carbon/epoxy laminates with molded edges

Directory of Open Access Journals (Sweden)

Cândido Geraldo Maurício

2000-01-01

Full Text Available The interlaminar stresses are confined to a region near the free edge. Therefore, the laminate stacking sequence and the free edge finishing are some of the factors that affect the strength of the laminate and limit its life. The use of molded edges eliminates the need for trimming and machining the laminates edges thus improving productivity. However, this fabrication technique may have a detrimental effect on the laminate strength for certain stacking sequences. This effect in the presence of moisture has not been characterized. This work presents the results of a comparative study of the resistance to delamination of laminates with machined edges and molded edges. Additionally, two environmental conditions were considered: dry laminates and laminates saturated with moisture. The tensile strength of the laminates were measured and micrographs were used to analyze the microstructure of the laminates near the free edges. It is concluded that the mechanical properties of advanced composites depend on the environmental conditions and the fabrication techniques used to produce the laminates. Therefore, it is necessary to account for these factors when experimentally determining the design allowables.

Efficacy of strength training on tension-type headache

DEFF Research Database (Denmark)

Madsen, Bjarne K; Søgaard, Karen; Andersen, Lars L

2018-01-01

Background Strength training has shown effects in reducing neck pain. As neck pain is highly prevalent in tension-type headache (TTH), it is relevant to examine the effect of strength training of the shoulder muscles on TTH patients. Aim To examine the effect of strength training of the shoulder....../neck muscles on TTH frequency and duration. Methods Sixty patients with TTH were randomised into strength training or a control group. The strength training group trained ten weeks with elastic resistance bands. The control group performed ergonomic and posture correction. Efficacy was evaluated at follow......-up after 19-22 weeks. Results Twenty-three patients completed strength training and 21 completed ergonomic and posture correction (per-protocol). No between-group effect was detected, but within groups numerical reductions were noted in both groups from baseline to follow-up. Frequency of TTH...

[Effects of surface treatment and adhesive application on shear bond strength between zirconia and enamel].

Science.gov (United States)

Li, Yinghui; Wu, Buling; Sun, Fengyang

2013-03-01

To evaluate the effects of sandblasting and different orthodontic adhesives on shear bond strength between zirconia and enamel. Zirconia ceramic samples were designed and manufactured for 40 extracted human maxillary first premolars with CAD/CAM system. The samples were randomized into 4 groups for surface treatment with sandblasting and non-treated with adhesives of 3M Transbond XT or Jingjin dental enamel bonding resin. After 24 h of bonded fixation, the shear bond strengths were measured by universal mechanical testing machine and analyzed with factorial variance analysis. The shear bond strength was significantly higher in sandblasting group than in untreated group (Padhesives of Transbond XT and dental enamel bonding resin (P>0.05). The shear bond strength between zirconia and enamel is sufficient after sandblasting regardless of the application of either adhesive.

33 Effects of Sodium Chloride Solutions on Compressive Strength ...

African Journals Online (AJOL)

Arc. Usman A. Jalam

strength increase at 3 and 7 days over control cubes; at 28 days concrete cubes containing 5%. RHA cured in NaCl solutions recorded higher strength loss compared to control cubes. Keywords: ... chloride in mixing water reported it to cause.

The effect of spinal manipulation on imbalances in leg strength.

Science.gov (United States)

Chilibeck, Philip D; Cornish, Stephen M; Schulte, Al; Jantz, Nathan; Magnus, Charlene R A; Schwanbeck, Shane; Juurlink, Bernhard H J

2011-09-01

We hypothesized that spinal manipulation (SM) would reduce strength imbalances between legs. Using an un-blinded randomized design, 28 males and 21 females (54 ± 19y) with at least a 15% difference in isometric strength between legs for hip flexion, extension, abduction, or knee flexion were randomized to treatment or placebo (mock spinal manipulation). Strength of the stronger and weaker legs for hip flexion, extension, abduction, and/or knee flexion was assessed before and after the intervention. SM reduced the relative strength difference between legs for knee flexion (mean ± SD 57 ± 53 to 5 ± 14%) and hip flexion (24 ± 12 to 11 ± 15%) compared to placebo (34 ± 29 to 24 ± 36%, and 20 ± 18 to 22 ± 26%, respectively) (p = 0.05). SM also improved strength in the weak leg for hip abduction (104 ± 43 to 116 ± 43 Nm) compared to placebo (84 ± 24 to 85 ± 31 Nm) (p = 0.03). This study suggests that spinal manipulation may reduce imbalances in strength between legs for knee and hip flexion.

Effect of repair resin type and surface treatment on the repair strength of polyamide denture base resin.

Science.gov (United States)

Gundogdu, Mustafa; Yanikoglu, Nuran; Bayindir, Funda; Ciftci, Hilal

2015-01-01

The purpose of the present study was to evaluate the effects of different repair resins and surface treatments on the repair strength of a polyamide denture base material. Polyamide resin specimens were prepared and divided into nine groups according to the surface treatments and repair materials. The flexural strengths were measured with a 3-point bending test. Data were analyzed with a 2-way analysis of variance, and the post-hoc Tukey test (α=0.05). The effects of the surface treatments on the surface of the polyamide resin were examined using scanning electron microscopy. The repair resins and surface treatments significantly affected the repair strength of the polyamide denture base material (p0.05). The flexural strength of the specimens repaired with the polyamide resin was significantly higher than that of those repaired with the heat-polymerized and autopolymerizing acrylic resins.

Effects of Elastic Resistance Exercise on Muscle Strength and Functional Performance in Healthy Adults: A Systematic Review and Meta-Analysis.

Science.gov (United States)

de Oliveira, Poliana Alves; Blasczyk, Juscelino Castro; Souza Junior, Gerson; Lagoa, Karina Ferreira; Soares, Milene; de Oliveira, Ricardo Jacó; Filho, Paulo José Barbosa Gutierres; Carregaro, Rodrigo Luiz; Martins, Wagner Rodrigues

2017-04-01

Elastic Resistance Exercise (ERE) has already demonstrated its effectiveness in older adults and, when combined with the resistance generated by fixed loads, in adults. This review summarizes the effectiveness of ERE performed as isolated method on muscle strength and functional performance in healthy adults. A database search was performed (MEDLine, Cochrane Library, PEDro and Web of Knowledge) to identify controlled clinical trials in English language. The mean difference (MD) with 95% confidence intervals (CIs) and overall effect size were calculated for all comparisons. The PEDro scale was used assess the methodological quality. From the 93 articles identified by the search strategy, 5 met the inclusion criteria, in which 3 presented high quality (PEDro > 6). Meta-analyses demonstrated that the effects of ERE were superior when compared with passive control on functional performance and muscle strength. When compared with active controls, the effect of ERE was inferior on function performance and with similar effect on muscle strength. ERE are effective to improve functional performance and muscle strength when compared with no intervention, in healthy adults. ERE are not superior to other methods of resistance training to improve functional performance and muscle strength in health adults.

Behavior of hybrid high-strength fiber reinforced concrete slab-column connections under the effect of high tempera

Directory of Open Access Journals (Sweden)

Reham H. Ahmed

2016-04-01

Full Text Available Concrete can be modified to perform in a more ductile form by the addition of randomly distributed discrete fibers in the concrete matrix. The combined effect of the addition of two types of fibers (steel fiber and polypropylene fiber with different percentages to concrete matrix, which is called hybrid effect is currently under investigation worldwide. The current research work presents the conducted experimental program to observe the behavior of hybrid high strength reinforced concrete slab-column connections under the effect of high temperature. For this purpose, ten slab-column connections were casted and tested. The experimental program was designed to investigate the effect of different variables such as concrete mixture, column location and temperature fighting system. All specimens were exposed to a temperature of 500 °C for duration of two hours. To observe the effect of each variable, specimens were divided into four groups according to the studied parameters. The test results revealed that using hybrid high strength concrete HFHSC produced more strength in punching failure compared with high strength concrete HSC when exposed to elevated temperature. Fighting by air had higher initial crack load compared with that for without fighting and fighting by water. On the other hand, fighting by water decreased the ultimate load.

Bonding polycarbonate brackets to ceramic: : Effects of substrate treatment on bond strength

NARCIS (Netherlands)

Özcan, Mutlu; Vallittu, Pekka K.; Peltomäki, Timo; Huysmans, Marie-Charlotte; Kalk, Warner

2004-01-01

This study evaluated the effects of 5 different surface conditioning methods on the bond strength of polycarbonate brackets bonded to ceramic surfaces with resin based cement. Six disc-shaped ceramic specimens (feldspathic porcelain) with glazed surfaces were used for each group. The specimens were

EFFECT OF ECCENTRIC EXERCISE PROGRAMME ON PAIN AND GRIP STRENGTH FOR SUBJECTS WITH MEDIAL EPICONDYLITIS

Directory of Open Access Journals (Sweden)

Mishra Prashant Akhilesh

2014-04-01

Full Text Available Background and Objective: Therapeutic eccentric exercise may provide both a structural and functional benefit during tendinopathy rehabilitation. The objective is to find the effect of eccentric exercises on improvement of pain and grip strength for subjects with Medial Epicondylitis. Method: Pre to post test experimental study design randomized thirty subjects with medial epicondylitis, 15 each into Group A and Group B. Group B subjects were treated with conventional therapy and Eccentric exercises. Group A subjects were treated with conventional therapy. Results: When means of post intervention were compared using Independent ‘t’ between groups there was no statistically significant difference in improvements obtained in VAS scores and grip strength. There was a statistically significant change in means of VAS score and Grip strength when means were analyzed by using Paired‘t’ test and Wilcoxon signed rank test within the groups with positive percentage of change. Conclusion: It is concluded that four weeks of Eccentric Exercise Programme combined with conventional therapy shown significant effect on improving pain and Grip strength, however the improvement obtained has no difference when compared with control conventional treatment for Subjects with Medial Epicondylitis.

Impact strength on fiber-reinforced hybrid composite

International Nuclear Information System (INIS)

Firdaus, S M; Nurdina; Ariff, M Azmil

2013-01-01

Acrylonitrile-Butadiene-Styrene (ABS) has been well known composite in automotive players to have light weight with high impact strength material compared to sheet metal material which has high impact strength but heavy in weight. In this project, the impact strength properties of fabricated pure ABS were compared to the eight samples of hybrid ABS composite with different weight percentages of short fibers and particle sizes of ground rubber. The objective was to improve the impact strength in addition of short fibers and ground rubber particles. These samples were then characterized using an un-notched Izod impact test. Results show that the increasing of filler percentage yielded an adverse effect on the impact strength of the hybrid composite. The effect of the ground rubber particulate sizes however are deemed to be marginal than the effect of varying filler percentage based on the collected impact strength data from all physically tested hybrid composites

Effects of pH and ionic strength on the thermodynamics of human serum albumin-photosensitizer binding

International Nuclear Information System (INIS)

Jones, Cecil L.; Dickson, TiReJe; Hayes, Ronald; Thomas, Lana

2012-01-01

Highlights: ► The pH dependence of entropy and enthalpy changes was determined for zinc phthalocyanine tetrasulfonic acid, ZnPcS 4 binding to human serum albumin, HSA. ► The ionic strength dependence of entropy and enthalpy changes was determined for ZnPcS 4 acid binding to HSA. ► The primary driving force governing the interaction between ZnPcS 4 and HSA over the range of pH and ionic strength was solution dynamics. ► The interplay between entropy and enthalpy changes was demonstrated. - Abstract: Fluorescence spectroscopy was used to measure the effects of pH and ionic strength on thermodynamic parameters governing the interaction of human serum albumin with zinc phthalocyanine tetrasulfonic acid. Fluorescence emission of zinc phthalocyanine increases at 686 nm with increasing concentrations of the protein. The non-linear correlation between protein concentration and emission of the photosensitizer was fitted using Chipman's analysis to calculate the binding affinities. The standard enthalpy and entropy changes were estimated from van’t Hoff analysis of data that were acquired from temperature ramping studies. Results show that reaction is primarily driven by solution dynamics and that the change in enthalpy for the system becomes increasingly unfavorable with increasing pH and ionic strength. The effect of ionic strength on the entropy change for binding is shown to be significantly greater than the effects of pH. The interplay between entropy and enthalpy changes is demonstrated.

Δ effects in pion-nucleon scattering and the strength of the two-pion-exchange three-nucleon interaction

International Nuclear Information System (INIS)

Pandharipande, V.R.; Phillips, D.R.; Kolck, U. van

2005-01-01

We consider the relationship between p-wave πN scattering and the strength of the p-wave two-pion-exchange three-nucleon interaction (TPE3NI). We explain why effective theories that do not contain the Delta resonance as an explicit degree of freedom tend to overestimate the strength of the TPE3NI. The overestimation can be remedied by higher-order terms in these 'Delta-less' theories, but such terms are not yet included in state-of-the-art chiral effective field theory calculations of the nuclear force. This suggests that these calculations can predict the strength of the TPE3NI only to an accuracy of ±25%

Shear Bond Strength of Orthodontic Brackets and Disinclusion Buttons: Effect of Water and Saliva Contamination

Science.gov (United States)

Sfondrini, Maria Francesca; Fraticelli, Danilo; Gandini, Paola

2013-01-01

Purpose. The aim of this study was to assess the effect of water and saliva contamination on the shear bond strength and failure site of orthodontic brackets and lingual buttons. Materials and Methods. 120 bovine permanent mandibular incisors were randomly divided into 6 groups of 20 specimens each. Both orthodontic brackets and disinclusion buttons were tested under three different enamel surface conditions: (a) dry, (b) water contamination, and (c) saliva contamination. Brackets and buttons were bonded to the teeth and subsequently tested using a Instron universal testing machine. Shear bond strength values and adhesive failure rate were recorded. Statistical analysis was performed using ANOVA and Tukey tests (strength values) and Chi squared test (ARI Scores). Results. Noncontaminated enamel surfaces showed the highest bond strengths for both brackets and buttons. Under water and saliva contamination orthodontic brackets groups showed significantly lower shear strengths than disinclusion buttons groups. Significant differences in debond locations were found among the groups under the various enamel surface conditions. Conclusions. Water and saliva contamination of enamel during the bonding procedure lowers bond strength values, more with orthodontic brackets than with disinclusion buttons. PMID:23762825

Shear Bond Strength of Orthodontic Brackets and Disinclusion Buttons: Effect of Water and Saliva Contamination

Directory of Open Access Journals (Sweden)

Maria Francesca Sfondrini

2013-01-01

Full Text Available Purpose. The aim of this study was to assess the effect of water and saliva contamination on the shear bond strength and failure site of orthodontic brackets and lingual buttons. Materials and Methods. 120 bovine permanent mandibular incisors were randomly divided into 6 groups of 20 specimens each. Both orthodontic brackets and disinclusion buttons were tested under three different enamel surface conditions: (a dry, (b water contamination, and (c saliva contamination. Brackets and buttons were bonded to the teeth and subsequently tested using a Instron universal testing machine. Shear bond strength values and adhesive failure rate were recorded. Statistical analysis was performed using ANOVA and Tukey tests (strength values and Chi squared test (ARI Scores. Results. Noncontaminated enamel surfaces showed the highest bond strengths for both brackets and buttons. Under water and saliva contamination orthodontic brackets groups showed significantly lower shear strengths than disinclusion buttons groups. Significant differences in debond locations were found among the groups under the various enamel surface conditions. Conclusions. Water and saliva contamination of enamel during the bonding procedure lowers bond strength values, more with orthodontic brackets than with disinclusion buttons.

Stochastic differential equations used to model conjugation

DEFF Research Database (Denmark)

Philipsen, Kirsten Riber; Christiansen, Lasse Engbo

Stochastic differential equations (SDEs) are used to model horizontal transfer of antibiotic resis- tance by conjugation. The model describes the concentration of donor, recipient, transconjugants and substrate. The strength of the SDE model over the traditional ODE models is that the noise can...

Effects of fatigue and environment on residual strengths of center-cracked graphite/epoxy buffer strip panels

Science.gov (United States)

Bigelow, Catherine A.

1989-01-01

The effects of fatigue, moisture conditioning, and heating on the residual tension strengths of center-cracked graphite/epoxy buffer strip panels were evaluated using specimens made with T300/5208 graphite epoxy in a 16-ply quasi-isotropic layup, with two different buffer strip materials, Kevlar-49 or S-glass. It was found that, for panels subjected to fatigue loading, the residual strengths were not significantly affected by the fatigue loading, the number of repetitions of the loading spectrum, or the maximum strain level. The moisture conditioning reduced the residual strengths of the S-glass buffer strip panels by 10 to 15 percent below the ambient results, but increased the residual strengths of the Kevlar-49 buffer strip panels slightly. For both buffer strip materials, the heat increased the residual strengths of the buffer strip panels slightly over the ambient results.

Increasing Lean Mass and Strength: A Comparison of High Frequency Strength Training to Lower Frequency Strength Training.

Science.gov (United States)

Thomas, Michael H; Burns, Steve P

The purpose of this study was to determine the effect strength training frequency has on improvements in lean mass and strength. Participants were 7 women and 12 men, age ( χ̄ = 34.64 years ± 6.91 years), with strength training experience, training age ( χ̄ = 51.16 months ± 39.02 months). Participants were assigned to one of two groups to equal baseline group demographics. High frequency training group (HFT) trained each muscle group as the agonist, 3 times per week, exercising with 3 sets per muscle group per session (3 total body workouts). Low frequency training group (LFT) trained each muscle group as the agonist one time per week, completing all 9 sets during that one workout. LFT consisted of a routine split over three days: 1) pectoralis, deltoids, and triceps; 2) upper back and biceps; 3) quadriceps, hamstrings, calves, and abdominals. Following eight weeks of training, HFT increased lean mass by 1.06 kg ± 1.78 kg, (1.9%), and LFT increased lean mass by .99 kg ± 1.31 kg, (2.0%). HFT strength improvements on the chest press was 9.07 kg ± 6.33 kg, (11%), and hack squat 20.16 kg ± 11.59 kg, (21%). LFT strength improvements on chest press was 5.80kg ± 4.26 kg, (7.0%), and hack squat 21.83 kg ± 11.17 kg, (24 %). No mean differences between groups were significant. These results suggest that HFT and LFT of equal set totals result in similar improvements in lean mass and strength, following 8 weeks of strength training.

Experimental knee joint pain during strength training and muscle strength gain in healthy subjects: a randomized controlled trial.

Science.gov (United States)

Sørensen, T J; Langberg, H; Hodges, P W; Bliddal, H; Henriksen, M

2012-01-01

Knee joint pain and reduced quadriceps strength are cardinal symptoms in many knee pathologies. In people with painful knee pathologies, quadriceps exercise reduces pain, improves physical function, and increases muscle strength. A general assumption is that pain compromises muscle function and thus may prevent effective rehabilitation. This study evaluated the effects of experimental knee joint pain during quadriceps strength training on muscle strength gain in healthy individuals. Twenty-seven healthy untrained volunteers participated in a randomized controlled trial of quadriceps strengthening (3 times per week for 8 weeks). Participants were randomized to perform resistance training either during pain induced by injections of painful hypertonic saline (pain group, n = 13) or during a nonpainful control condition with injection of isotonic saline (control group, n = 14) into the infrapatellar fat pad. The primary outcome measure was change in maximal isokinetic muscle strength in knee extension/flexion (60, 120, and 180 degrees/second). The group who exercised with pain had a significantly larger improvement in isokinetic muscle strength at all angular velocities of knee extension compared to the control group. In knee flexion there were improvements in isokinetic muscle strength in both groups with no between-group differences. Experimental knee joint pain improved the training-induced gain in muscle strength following 8 weeks of quadriceps training. It remains to be studied whether knee joint pain has a positive effect on strength gain in patients with knee pathology. Copyright © 2012 by the American College of Rheumatology.

Fatigue strength of repaired cracks in welded connections made of very high strength steels

NARCIS (Netherlands)

Akyel, A.

2017-01-01

For cyclically loaded structures, fatigue design becomes one of the important design criteria. The state of art shows that with modification of the conventional structural design methodology, the use of very high strength steels may have a positive effect on fatigue strength of welded connections.

Effect of ZrO2 on the sintering behavior, strength and high-frequency dielectric properties of electrical ceramic porcelain insulator

Science.gov (United States)

Singh Mehta, Niraj; Sahu, Praveen Kumar; Ershad, Md; Saxena, Vipul; Pyare, Ram; Ranjan Majhi, Manas

2018-01-01

In the present study, the effect of ZrO2 on the sintering, strength and dielectric behavior of electrical ceramic porcelain insulator with substituting alumina content by zirconia (in weight percentage from 0% to 30%) is investigated. The different composition of samples containing different zirconia (ZrO2) contents of 0, 10, 20, and 30 wt% are prepared using the uniaxial pressure technique applying 160 MPa pressure. Further, the prepared samples are also analyzed for sintering temperatures (1350 °C), and effects are observed on mechanical and electric properties of porcelain insulator. Different characterizations such as Dilatometer, x-ray diffraction, scanning electron microscopy and differential thermal analysis/thermo gravimetric analysis were used to evaluate the thermal, phase detection, micro structural and weight loss changes by increasing concentration of ZrO2 on base porcelain composition. At 1350 °C, for the composition having 20 wt% ZrO2 with 10 wt% alumina, the maximum density was observed 2.81 g cm-3 with a porosity of 2.23%. The highest tensile strength of 41 ± 3 MPa is observed for the same sample composition. The minimum value of thermal expansion coefficient is found to be in the range of 10-6 for the sample with 30 wt% ZrO2 content sintered at 1350 °C compared to other prepared samples. Similarly, the highest dielectric value (5.1-4.4) having dielectric loss (0.08-0.12) is achieved for the sample with 30 wt% ZrO2 content sintered at 1350 °C in the frequency range of 4-20 GHz at room temperature. According to the mechanical properties, the composition having 20 wt% ZrO2 on base ceramic porcelain composition has enormous potential to serve as a high strength refractory material. For dielectric properties, the composition having 30 wt% ZrO2 is more suitable for the electrical application.

Effect of surface treatment of titanium posts on the tensile bond strength

NARCIS (Netherlands)

Schmage, P; Sohn, J; Ozcan, M; Nergiz, [No Value

Objectives. Retention of composite resins to metal can be improved when metal surfaces are conditioned. The purpose of this investigation was to investigate the effect of two conditioning treatments on the tensile bond strength of four resin-based luting cements and zinc phosphate cement to titanium

Effect of different dispersants in compressive strength of carbon fiber cementitious composites

Science.gov (United States)

Lestari, Yulinda; Bahri, Saiful; Sugiarti, Eni; Ramadhan, Gilang; Akbar, Ari Yustisia; Martides, Erie; Khaerudini, Deni S.

2013-09-01

Carbon Fiber Cementitious Composites (CFCC) is one of the most important materials in smart concrete applications. CFCC should be able to have the piezoresistivity properties where its resistivity changes when there is applied a stress/strain. It must also have the compressive strength qualification. One of the important additives in carbon fiber cementitious composites is dispersant. Dispersion of carbon fiber is one of the key problems in fabricating piezoresistive carbon fiber cementitious composites. In this research, the uses of dispersants are methylcellulose, mixture of defoamer and methylcellulose and superplasticizer based polycarboxylate. The preparation of composite samples is similar as in the mortar technique according to the ASTM C 109/109M standard. The additives material are PAN type carbon fibers, methylcellulose, defoamer and superplasticizer (as water reducer and dispersant). The experimental testing conducts the compressive strength and resistivity at various curing time, i.e. 3, 7 and 28 days. The results obtained that the highest compressive strength value in is for the mortar using superplasticizer based polycarboxylate dispersant. This also shown that the distribution of carbon fiber with superplasticizer is more effective, since not reacting with the cementitious material which was different from the methylcellulose that creates the cement hydration reaction. The research also found that the CFCC require the proper water cement ratio otherwise the compressive strength becomes lower.

Effect of a step-training program on muscle strength in older women

Directory of Open Access Journals (Sweden)

Daniela Coelho Zazá

2010-04-01

Full Text Available Step-training is associated with strength improvement of the lower limbs. Muscle strength is a critical component for the maintenance of functional capacity. The objective of the present study was to determine the effect of 6 weeks of step-training on work and power of the lower limbs in older women. Thirteen healthy and active women volunteered to participate in the study. All subjects underwent step-training classes three times per week for 60 min. Strength variables of the knee extensor and flexor muscles were measured with a Biodex System 3 Pro isokinetic dynamometer. Muscle work and power were assessed at an angular velocity of 60 and 180°/s. A significant difference (p<0.05 in knee flexor muscle work was observed between pre- and post-test at 60 and 180°/s. There was a significant difference (p<0.05 in knee extensor muscle work between pre- and post-test at 60°/s. Significant differences were observed between pre- and post-test values of knee flexor muscle power at 60°/s (p<0.05 and knee extensor muscle power at 60 and 180°/s (p<0.05. In conclusion, step-training can be recommended as an alternative physical activity to increase strength performance (work and power of the knee extensor and flexor muscles in older subjects.

Effects of complex training on explosive strength in adolescent male basketball players.

Science.gov (United States)

Santos, Eduardo J A M; Janeira, Manuel A A S

2008-05-01

The purpose of this study was to evaluate the effects of a complex training program, a combined practice of weight training and plyometrics, on explosive strength development of young basketball players. Twenty-five young male athletes, aged 14-15 years old, were assessed using squat jump (SJ), countermovement jump (CMJ), Abalakov test (ABA), depth jump (DJ), mechanical power (MP), and medicine ball throw (MBT), before and after a 10-week in-season training program. Both the control group (CG; n = 10) and the experimental group (EG; n = 15) kept up their regular sports practice; additionally, the EG performed 2 sessions per week of a complex training program. The EG significantly improved in the SJ, CMJ, ABA, and MBT values (p training to improve the upper and lower body explosivity levels in young basketball players. In conclusion, this study showed that more strength conditioning is needed during the sport practice season. Furthermore, we also conclude that complex training is a useful working tool for coaches, innovative in this strength-training domain, equally contributing to a better time-efficient training.

Effects of trichostatins on differentiation of murine erythroleukemia cells

International Nuclear Information System (INIS)

Yoshida, M.; Nomura, S.; Beppu, T.

1987-01-01

The fungistatic antibiotics trichostatins (TS) A and C were isolated from culture broth of Streptomyces platensis No. 145 and were found to be potent inducers of differentiation in murine erythroleukemia (Friend and RV133) cells at concentrations of 1.5 X 10(-8) M for TSA and 5 X 10(-7) M for TSC. Differentiation induced by TS was cooperatively enhanced by UV irradiation but not by treatment with dimethyl sulfoxide. This enhanced activity was completely inhibited by adding cycloheximide to the culture medium 2 h after exposure to TS, suggesting that TS are dimethyl sulfoxide-type inducers of erythroid differentiation. No inhibitory effect of TS was observed on macromolecular synthesis in cultured cells

The effect of basketball training on the muscle strength of adults with mental retardation.

Science.gov (United States)

Tsimaras, Vasilios K; Samara, Christina A; Kotzamanidou, Marianna C; Bassa, Eleni I; Fotiadou, Eleni G; Kotzamanidis, Christos M

2009-12-01

The purpose of this study was to evaluate the effect of basketball training on the muscle strength of adults with mental retardation (MR). Twenty-four adults with and without MR were separated into 3 groups. Eight adults (mean age 25.4 years) with normal IQ constituted the control group (NIQ). Eight adults (mean age 26.5 years) with MR and all participating in a 4-year systematic basketball exercise program constituted the trained group (MR-T), and 8 adults (mean age 25.3 years) with MR exercised occasionally for recreational reasons formed the MR-R group. Parameters measured were isometric and isokinetic concentric and eccentric muscle strength. All subjects performed a leg strength test on a Cybex Norm isokinetic dynamometer. Analysis of variance was used to examine mean differences between the values of the 3 groups. A significance level of 0.05 was used for all tests. The NIQ group showed a statistically significant difference in all measured values compared to the MR groups. The MR-T group presented higher absolute and relative torque scores for both knee extensors and flexors than the MR-R group, whereas the MR-R group presented statistically higher antagonistic activity for both knee extensors and flexors than the MR-T group. In addition, both MR groups presented statistically higher antagonistic activity for both knee extensors and flexors compared to the NIQ group. Data support participation on a systematic and well-designed basketball training program to improve muscle strength levels of adults with MR. Participation in basketball without necessarily focusing on developing specific fitness components may be an effective training strategy for the promotion of strength of adults with MR.

Effects of Exercise Modality During Additional "High-Intensity Interval Training" on Aerobic Fitness and Strength in Powerlifting and Strongman Athletes.

Science.gov (United States)

Androulakis-Korakakis, Patroklos; Langdown, Louis; Lewis, Adam; Fisher, James P; Gentil, Paulo; Paoli, Antonio; Steele, James

2018-02-01

Androulakis-Korakakis, P, Langdown, L, Lewis, A, Fisher, JP, Gentil, P, Paoli, A, and Steele, J. Effects of exercise modality during additional "high-intensity interval training" on aerobic fitness and strength in powerlifting and strongman athletes. J Strength Cond Res 32(2): 450-457, 2018-Powerlifters and strongman athletes have a necessity for optimal levels of muscular strength while maintaining sufficient aerobic capacity to perform and recover between events. High-intensity interval training (HIIT) has been popularized for its efficacy in improving both aerobic fitness and strength but never assessed within the aforementioned population group. This study looked to compare the effect of exercise modality, e.g., a traditional aerobic mode (AM) and strength mode (SM), during HIIT on aerobic fitness and strength. Sixteen well resistance-trained male participants, currently competing in powerlifting and strongman events, completed 8 weeks of approximately effort- and volume-matched HIIT in 2 groups: AM (cycling, n = 8) and SM (resistance training, n = 8). Aerobic fitness was measured as predicted V[Combining Dot Above]O2max using the YMCA 3 minutes step test and strength as predicted 1 repetition maximum from a 4-6RM test using a leg extension. Both groups showed significant improvements in both strength and aerobic fitness. There was a significant between-group difference for aerobic fitness improvements favoring the AM group (p ≤ 0.05). There was no between-group difference for change in strength. Magnitude of change using within-group effect size for aerobic fitness and strength was considered large for each group (aerobic fitness, AM = 2.6, SM = 2.0; strength, AM = 1.9, SM = 1.9). In conclusion, our results support enhanced strength and aerobic fitness irrespective of exercise modality (e.g., traditional aerobic and resistance training). However, powerlifters and strongman athletes wishing to enhance their aerobic fitness should consider HIIT using an

The effect of display movement angle, indicator type and display location on control/display stereotype strength.

Science.gov (United States)

Hoffmann, Errol R; Chan, Alan H S

2017-08-01

Much research on stereotype strength relating display and control movements for displays moving in the vertical or horizontal directions has been reported. Here we report effects of display movement angle, where the display moves at angles (relative to the vertical) of between 0° and 180°. The experiment used six different controls, four display locations relative to the operator and three types of indicator. Indicator types were included because of the strong effects of the 'scale-side principle' that are variable with display angle. A directional indicator had higher stereotype strength than a neutral indicator, and showed an apparent reversal in control/display stereotype direction beyond an angle of 90°. However, with a neutral indicator this control reversal was not present. Practitioner Summary: The effects of display moving at angles other than the four cardinal directions, types of control, location of display and types of indicator are investigated. Indicator types (directional and neutral) have an effect on stereotype strength and may cause an apparent control reversal with change of display movement angle.

Effects of Cu and B addition on microstructure and mechanical properties of high-strength bainitic steels

International Nuclear Information System (INIS)

Shin, Sang Yong; Han, Seung Youb; Hwang, Byoungchul; Lee, Chang Gil; Lee, Sunghak

2009-01-01

Effects of Cu and B addition on microstructure and mechanical properties of high-strength bainitic steels were investigated in this study. Six kinds of steels were fabricated by controlling the amount of Cu and B addition, and their microstructures and tensile and Charpy impact properties were investigated. Their effective grain sizes were also characterized by the electron back-scatter diffraction analysis. The tensile test results indicated that the B- or Cu-containing steels had the higher yield and tensile strengths than the B- or Cu-free steels because their volume fractions of acicular ferrite and martensite were quite high. The B- or Cu-free steels had the higher upper shelf energy than the B- or Cu-containing steels because of their lower volume fraction of martensite. In the steel containing 10 ppm B without Cu, the best combination of high strengths, high upper shelf energy, and low energy transition temperature could be obtained by the decrease in effective grain size due to the presence of acicular ferrite having fine effective grain size.

Effect of Two-minute Application of 35% Sodium Ascorbate on Composite Bond Strength following Bleaching.

Science.gov (United States)

Ismail, Eman H; Kilinc, Evren; Hardigan, Patrick C; Rothrock, James K; Thompson, Jeffrey Y; Garcia-Godoy, Cristina

2017-10-01

The aim of this study is to assess the effect of 35% sodium ascorbate on microtensile bond strength of dentin immediately after bleaching with 35% hydrogen peroxide. A total of 25 sound human 3 rd molars were collected. Teeth were randomly divided into five groups for different treatments: Group I [bleaching + immediate bonding (i.e., restoration)], group II (bleaching + delayed bonding), group III (bleaching + sodium ascorbate + immediate bonding), group IV (bleaching + sodium ascorbate + delayed bonding), and group V (bonding only). After bleaching, but before bonding, groups II and IV were stored for 1 week in deionized water at 37°C. All samples were bonded using OptiBoned FL (Kerr) and Filtek Supreme (3M/ESPE). Teeth were sectioned into 1 × 1 mm 2 bars, and microtensile bond strength was tested with a universal testing machine (Instron 8841) at a cross-head speed of 0.5 mm/minute. Microtensile bond strength differed significantly across the five groups, with a significant reduction in microtensile bond strength observed for samples in group I relative to samples in any of the other treatment groups (p bleaching on composite bonding strength to dentin. The negative effects of bleaching on composite bonding can be neutralized by the application of the reversing agent sodium ascorbate thus, increasing the efficiency of clinic chair time. This is clinically relevant for those patients requiring restorative treatment immediately after in-office bleaching.

Effect of microwave postpolymerization treatment on residual monomer content and the flexural strength of autopolymerizing reline resin

Directory of Open Access Journals (Sweden)

Patil Padmakar

2009-01-01

Full Text Available Background : Microwave postpolymerization has been suggested as a method to improve the flexural strength of an autopolymerizing denture reline resin. However, the effect of microwave postpolymerization on the residual monomer content and its influence on flexural strength have not been investigated. Objectives : This study analyzed the effect of microwave postpolymerization on the residual monomer content and its influence on the flexural strength of an autopolymerizing reline resin (Denture Liner. Materials and Methods : A total of 70 specimens (64 Χ 10 Χ 3.3 mm were polymerized according to the manufacturer′s instructions and divided into 7 groups (n = 10. Control group specimens were not subjectedto any further processing. Before testing, the specimens were subjected to postpolymerization in a microwave oven using different power (550 and 650 W and time (3, 4, and 5 min settings. Two specimens of each group were then manually ground into fine powder and samples extracted from the specimens using reflux method. The samples were then subjected to gas chromatography for residual monomer determination in area%. Eight specimens were subjected to a three-point bending device with a span of 50 mm and crosshead speed of 5 mm/min, and the flexural strength was determined in MPa. Data analyses included Student′s t-test and one-way analysis of variance. Results : For the Denture Liner reline resin, the residual monomer content decreased and the flexural strength increased significantly with the application of microwave irradiation using different time/power combinations. The specimens with the lowest residual monomer content were the similar specimens which presented with the highest flexural strength. Conclusion : Microwave postpolymerization irradiation can be an effective method for increasing the flexural strength of denture liner (at 650 W for 5 min by reducing the residual monomer content by further polymerization at free radical sites.

EFFECT OF SODIUM HYDROXIDE CONCENTRATION ON FRESH PROPERTIES AND COMPRESSIVE STRENGTH OF SELF-COMPACTING GEOPOLYMER CONCRETE

Directory of Open Access Journals (Sweden)

FAREED AHMED MEMON

2013-02-01

Full Text Available This paper reports the results of the laboratory tests conducted to investigate the effect of sodium hydroxide concentration on the fresh properties and compressive strength of self-compacting geopolymer concrete (SCGC. The experiments were conducted by varying the concentration of sodium hydroxide from 8 M to 14 M. Test methods such as Slump flow, V-Funnel, L-box and J-Ring were used to assess the workability characteristics of SCGC. The test specimens were cured at 70°C for a period of 48 hours and then kept in room temperature until the day of testing. Compressive strength test was carried out at the ages of 1, 3, 7 and 28 days. Test results indicate that concentration variation of sodium hydroxide had least effect on the fresh properties of SCGC. With the increase in sodium hydroxide concentration, the workability of fresh concrete was slightly reduced; however, the corresponding compressive strength was increased. Concrete samples with sodium hydroxide concentration of 12 M produced maximum compressive strength.

The Effect of Two Different Concurrent Training Programs on Strength and Power Gains in Highly-Trained Individuals

Science.gov (United States)

Petré, Henrik; Löfving, Pontus; Psilander, Niklas

2018-01-01

The effects of concurrent strength and endurance training have been well studied in untrained and moderately-trained individuals. However, studies examining these effects in individuals with a long history of resistance training (RT) are lacking. Additionally, few studies have examined how strength and power are affected when different types of endurance training are added to an RT protocol. The purpose of the present study was to compare the effects of concurrent training incorporating either low-volume, high-intensity interval training (HIIT, 8-24 Tabata intervals at ~150% of VO2max) or high-volume, medium-intensity continuous endurance training (CT, 40-80 min at 70% of VO2max), on the strength and power of highly-trained individuals. Sixteen highly-trained ice-hockey and rugby players were divided into two groups that underwent either CT (n = 8) or HIIT (n = 8) in parallel with RT (2-6 sets of heavy parallel squats, > 80% of 1RM) during a 6-week period (3 sessions/wk). Parallel squat performance improved after both RT + CT and RT + HIIT (12 ± 8% and 14 ± 10% respectively, p HIIT (4 ± 3%, p HIIT in athletes with a prior history of RT. This indicates that the volume and/or intensity of the endurance training does not influence the magnitude of strength improvements during short periods of concurrent training, at least for highly-trained individuals when the endurance training is performed after RT. However, since VO2max improved only after RT + HIIT and this is a time efficient protocol, we recommend this type of concurrent endurance training. Key points Lower body maximal strength is improved after concurrent strength and endurance training in highly trained individuals. The magnitude of this strength improvement is not influenced by the type of endurance training, i.e. HIIT or CT. HIIT improves VO2max and is more time efficient than CT. HIIT is recommended to athletes when concurrently training for strength and endurance. PMID:29769816

Determination of giant resonance strengths

International Nuclear Information System (INIS)

Serr, F.E.

1983-01-01

Using theoretical strength functions to describe the different giant resonances expected at excitation energies of the order of (60-85)/Asup(1/3) MeV, we calculate the double differential cross sections d 2 sigma/dΩ dE associated with the reactions 208 Pb(α, α') and 90 Zr(α, α') (Esub(α) = 152 MeV). The angular distributions for the giant quadrupole and giant monopole resonances obtained from fits to these spectra, making simple, commonly used assumptions for the peak shapes and background, are compared to the original angular distributions. The differences between them are an indication of some of the uncertainties affecting the giant resonance strengths extracted from hadron inelastic scattering data. Fits to limited angular regions lead to errors of up to 50% in the value of the energy-weighted sum rule, depending on the angles examined. While it seems possible to extract the correct EWSR for the GMR by carrying out the analyses at 0 0 , no single privileged angle seems to exist in the case of the GQR. (orig.)

Thermal Inertia of near-Earth Asteroids and Strength of the Yarkovsky Effect

NARCIS (Netherlands)

Delbo, Marco; Dell'Oro, A.; Harris, A. W.; Mottola, S.; Mueller, M.

2006-01-01

Thermal inertia is the physical parameter that controls the temperature distribution over the surface of an asteroid. It affects the strength of the Yarkovsky effect, which causes orbital drift of km-sized asteroids and is invoked to explain the delivery of near-Earth asteroids (NEAs) from the main

[The effect of core veneer thickness ratio on the flexural strength of diatomite-based dental ceramic].

Science.gov (United States)

Jiang, Jie; Zhang, Xin; Gao, Mei-qin; Zhang, Fei-min; Lu, Xiao-li

2015-06-01

To evaluate the effect of different core veneer thickness ratios on the flexural strength and failure mode of bilayered diatomite-based dental ceramics. Diatomite-based dental ceramics blocks (16 mm×5.4 mm×1 mm) were sintered with different thickness of veneer porcelains: 0 mm (group A), 0.6 mm (group B), 0.8 mm (group C) and 1.0 mm (group D). Flexural strength was detected and scanning electron microscope was used to observe the interface microstructure. Statistical analysis was performed using SPSS 17.0 software package. With the increase of the thickness of the veneer porcelain, flexural strength of group C showed highest flexural strength up to (277.24±5.47) MPa. Different core veneer thickness ratios can significantly influence the flexural strength of bilayered diatomite-based dental ceramics. Supported by Science and Technology Projects of Nantong City (HS2013010).

Differentiation of molecular chain entanglement structure through laser Raman spectrum measurement of High strength PET fibers under stress

Science.gov (United States)

Go, D.; Takarada, W.; Kikutani, T.

2017-10-01

The aim of this study was to investigate the mechanism for the improvement of mechanical properties of poly(ethylene terephthalate) (PET) fibers based on the concept of controlling the state of molecular entanglement. For this purpose, five different PET fibers were prepared through either the conventional melt spinning and drawing/annealing process or the high-speed melt spinning process. In both cases, the melt spinning process was designed so as to realize different Deborah number conditions. The prepared fibers were subjected to the laser Raman spectroscopy measurement and the characteristics of the scattering peak at around 1616 cm-1, which corresponds to the C-C/C=C stretching mode of the aromatic ring in the main chain, were investigated in detail. It was revealed that the fibers drawn and annealed after the melt spinning process of lower Deborah number showed higher tensile strength as well as lower value of full width at half maximum (FWHM) in the laser Raman spectrum. Narrow FWHM was considered to represent the homogeneous state of entanglement structure, which may lead to the higher strength and toughness of fibers because individual molecular chains tend to bare similar level of tensile stress when the fiber is stretched. In case of high-speed spun fibers prepared with a high Deborah number condition, the FWHM was narrow presumably because much lower tensile stress in comparison with the drawing/annealing process was applied when the fiber structure was developed, however the value increased significantly upon applying tensile load to the fibers during the laser Raman spectrum measurement. From these results, it was concluded that the Laser Raman spectroscopy could differentiate molecular chain entanglement structure of various fiber samples, in that low FWHM, which corresponds to either homogeneous state of molecular entanglement or lower level of mean residual stress, and small increase of FWTH upon applying tensile stress are considered to be the key

Effectiveness of Aquatic Exercise in Improving Lower Limb Strength in Musculoskeletal Conditions: A Systematic Review and Meta-Analysis.

Science.gov (United States)

Heywood, Sophie; McClelland, Jodie; Mentiplay, Benjamin; Geigle, Paula; Rahmann, Ann; Clark, Ross

2017-01-01

To investigate the effectiveness of aquatic exercise in improving lower limb strength in people with musculoskeletal conditions. A systematic search used 5 databases, including MEDLINE, CINAHL, Embase, SPORTDiscus, and The Cochrane Library. Randomized controlled trials evaluating aquatic exercise with a resistance training component for adults with musculoskeletal conditions compared with no intervention or land-based exercise were identified. Fifteen studies from the initial yield of 1214 met these criteria. Data related to participant demographics, study design, and methods, interventions, and outcomes, including numerical means and SDs, were extracted independently by 2 reviewers. Nine of the 15 studies were of high quality, scoring at least 6 on the Physiotherapy Evidence Database Scale. Limited consideration of the prescription of resistance in the aquatic exercise and application of resistance training principles existed. Low- or very low-quality evidence indicates there was no difference in average effect between aquatic exercise and no exercise in improving hip abductor strength (standardized mean difference [SMD], .28; 95% confidence interval [CI], -.04 to .59), knee extensor strength (SMD, .18; 95% CI, -.03 to .40), knee flexor strength (SMD, .13; 95% CI, -.20 to .45), or lower limb endurance (SMD, .35; 95% CI, -.06 to .77). Low-quality evidence indicates no difference in average effect between aquatic and land exercise for knee extensor (SMD, -.24; 95% CI, -.49 to .02) or flexor strength (SMD, -.15; 95% CI, -.53 to .22). It is likely that the inadequate application of resistance in water is a significant contributor to the limited effectiveness of aquatic exercise interventions in improving hip and knee muscle strength in people with musculoskeletal conditions. Future research is needed to quantify resistance with aquatic exercises and to determine if using opportunities for greater resistance in aquatic rehabilitation and appropriate resistance

Effect of resveratrol on proliferation and differentiation of embryonic cardiomyoblasts

International Nuclear Information System (INIS)

Leong, C.-W.; Wong, C.H.; Lao, S.-C.; Leong, Emilia Conceicao; Lao, Iok Fong; Law, Patrick Tik Wan; Fung, Kwok Pui; Tsang, Kam Sze; Waye, Mary Miu-Yee; Tsui, Stephen Kwok-Wing; Wang Yitao; Lee, Simon Ming-Yuen

2007-01-01

Resveratrol (trans-3,5,4'-trihydroxystilbene), a polyphenolic compound found largely in the skins of red grapes, has been used as a nutritional supplement or an investigational new drug for prevention of cardiovascular diseases. Previous reports showed that resveratrol had a protective effect against oxidative agent-induced cell injury. Our studies indicate that resveratrol plays a role in the differentiation of cardiomyoblasts. The cardiomyoblast cell line, H9c2, was exposed to 30-120 μM resveratrol for up to 5 days. Resveratrol inhibits cardiomyoblast proliferation without causing cells injury. Moreover, resveratrol treatment modulated the differentiation of morphological characteristics including elongation and cell fusion in cardiomyoblasts. Proliferation and differentiation of H9c2 cells were further revealed by measurement of the mRNA expression of a cell cycle marker (CDK2), a differentiation marker (myogenin), and a contractile apparatus protein (MLC-2). Gene expression analysis revealed that resveratrol promoted entry into cell cycle arrest but extended the myogenic differentiation progress. These results have implications for the role of resveratrol in modulating cell cycle control and differentiation in cardiomyoblasts

Effect of the Power Balance® hologram on balance, flexibility, strength and speed-coordination among university students

Directory of Open Access Journals (Sweden)

Rafael Merino Marban, Daniel Mayorga Vega, Emilio Fernández Rodríguez, Francisco José Santana Pérez, Oscar Romero Ramos

2011-01-01

Full Text Available Based on the body’s energy field, the inventors of Power Balance® have created a hologram that theoretically runs through frequencies that are in our natural environment. Its creators say that people may experience improve balance, strength, flexibility, endurance, concentration, coordination and recovery time, among others. The purpose of this research is to evaluate the effect of Power Balance® hologram on balance, flexibility, strength and speed-coordination in university students. A sample of 105 young volunteers’ physical education students (age 20.91 ± 3.36 years, mass 69.69 ± 11.35 kg, height 171.70 ± 8.07 cm was used. A between-group experimental design with double-blind control group was used to evaluate the possible effects of the Power Balance ® on the dynamic balance, flexibility, abdominal strength, endurance and speed-coordination measured with the Dynamic Balance Test, Sit and Reach, Sit-ups in 30 seconds and Race 10 x 5 m, respectively. A t of Student for independent and dependent samples was used to assess the potential effects between-group and intra-group, respectively. Power Balance®’s hologram produces no significant effects on the balance, flexibility, strength and speed-coordination among university students

The Effect of Fiber Strength Stochastics and Local Fiber Volume Fraction on Multiscale Progressive Failure of Composites

Science.gov (United States)

Ricks, Trenton M.; Lacy, Jr., Thomas E.; Bednarcyk, Brett A.; Arnold, Steven M.

2013-01-01

Continuous fiber unidirectional polymer matrix composites (PMCs) can exhibit significant local variations in fiber volume fraction as a result of processing conditions that can lead to further local differences in material properties and failure behavior. In this work, the coupled effects of both local variations in fiber volume fraction and the empirically-based statistical distribution of fiber strengths on the predicted longitudinal modulus and local tensile strength of a unidirectional AS4 carbon fiber/ Hercules 3502 epoxy composite were investigated using the special purpose NASA Micromechanics Analysis Code with Generalized Method of Cells (MAC/GMC); local effective composite properties were obtained by homogenizing the material behavior over repeating units cells (RUCs). The predicted effective longitudinal modulus was relatively insensitive to small (8%) variations in local fiber volume fraction. The composite tensile strength, however, was highly dependent on the local distribution in fiber strengths. The RUC-averaged constitutive response can be used to characterize lower length scale material behavior within a multiscale analysis framework that couples the NASA code FEAMAC and the ABAQUS finite element solver. Such an approach can be effectively used to analyze the progressive failure of PMC structures whose failure initiates at the RUC level. Consideration of the effect of local variations in constituent properties and morphologies on progressive failure of PMCs is a central aspect of the application of Integrated Computational Materials Engineering (ICME) principles for composite materials.

Effect of gap distance on tensile strength of preceramic base metal solder joints.

Science.gov (United States)

Fattahi, Farnaz; Motamedi, Milad

2011-01-01

In order to fabricate prostheses with high accuracy and durability, soldering techniques have been introduced to clinical dentistry. However, these prostheses always fail at their solder joints. The purpose of this study was to evaluate the effect of gap distance on the tensile strength of base metal solder joints. Based on ADA/ISO 9693 specifications for tensile test, 40 specimens were fabricated from a Ni-Cr alloy and cut at the midpoint of 3-mm diameter bar and placed at desired positions by a specially designed device. The specimens were divided into four groups of 10 samples according to the desired solder gap distance: Group1: 0.1mm; Group2: 0.25mm; Group3: 0.5mm; and Group4: 0.75mm. After soldering, specimens were tested for tensile strength by a universal testing machine at a cross-head speed of 0.5mm/min with a preload of 10N. The mean tensile strength values of the groups were 162, 307.8, 206.1 and 336.7 MPa, respectively. The group with 0.75-mm gap had the highest and the group with 0.1-mm gap had the lowest tensile strength. Bonferroni test showed that Group1 and Group4 had statistically different values (P=0.023), but the differences between other groups were not sig-nificant at a significance level of 0.05. There was no direct relationship between increasing soldering gap distance and tensile strength of the solder joints.

Effects of anti-sclerostin antibody and running on bone remodeling and strength

Directory of Open Access Journals (Sweden)

H. Toumi

2015-06-01

Full Text Available Sclerostin antibody (Scl-Ab represents a promising therapeutic approach to treat patients with osteoporosis. Purpose: The aim of this study was to investigate the effects of Scl-Ab, running and a combination of both on bone formation. Methods: Sixty female Wistar rats, aged 8 months were randomly assigned to five groups (subcutaneous injections performed twice a week: (1 (Sham: sedentary rats + saline, (2 (OVX: ovariectomized rats + saline, (3 (OVX + E: OVX rats + saline + treadmill training (5 times/week, 1 h/day, (4 (OVX + E + S: OVX rats + treadmill training + 5 mg/kg Scl-Ab and (5 (OVX + S: OVX rats + 5 mg/kg Scl-Ab. After 14 weeks, body composition, whole body and femoral BMDs were determined by DXA and serum was collected for analysis of osteocalcin and NTX. Bone microarchitecture was analyzed using μCT and bone strength was assessed at the femur mid-shaft in 3-point bending. Results: Running exercise decreased fat mass as well as the bone resorption marker NTX relative to the non-exercised control groups, effects that were associated with a prevention of the deleterious effects of OVX on whole body and femoral BMDs. Scl-Ab increased the bone formation marker osteocalcin, which resulted in robust increases in BMD and femoral metaphyseal bone volume to levels greater than in the Sham group. OVX + S + E group did not further impact on bone mass relative to the OVX + S group. At the cortical femur diaphysis, Scl-Ab prevented the decreases in bone strength after OVX, while exercise did not affect cortical strength. Conclusion: We suggest that while running on a treadmill can prevent some bone loss through a modest antiresorptive effect, it did not contribute to the robust bone-forming effects of Scl-Ab when combined in an estrogen ablation model.

Planning to break unwanted habits: habit strength moderates implementation intention effects on behaviour change.

Science.gov (United States)

Webb, Thomas L; Sheeran, Paschal; Luszczynska, Aleksandra

2009-09-01

Implementation intention formation promotes effective goal striving and goal attainment. However, little research has investigated whether implementation intentions promote behaviour change when people possess strong antagonistic habits. Experiment 1 developed relatively habitual responses that, after a task switch, had a detrimental impact on task performance. Forming an if-then plan reduced the negative impact of habit on performance. However, the effect of forming implementation intentions was smaller among participants who possessed strong habits as compared to participants who had weaker habits. Experiment 2 provided a field test of the role of habit strength in moderating the relationship between implementation intentions and behaviour in the context of smoking. Implementation intentions reduced smoking among participants with weak or moderate smoking habits, but not among participants with strong smoking habits. In summary, habit strength moderates the effectiveness of if-then plan formation in breaking unwanted habits.

Effect of blood contamination on shear bond strength of orthodontic brackets and disinclusion buttons.

Science.gov (United States)

Sfondrini, Maria Francesca; Gatti, Sara; Scribante, Andrea

2011-07-01

Our aim was to assess the effect of blood contamination on the shear bonding strength and sites of failure of orthodontic brackets and bondable buttons. We randomly divided 160 bovine permanent mandibular incisors into 8 groups of 20 specimens each. Both orthodontic brackets (Step brackets, Leone, Sesto Fiorentino, Italy) and bondable buttons (Flat orthodontic buttons, Leone, Sesto Fiorentino, Italy) were tested on four different enamel surfaces: dry; contamination with blood before priming; after priming; and before and after priming. Brackets and buttons were bonded to the teeth and subsequently tested using a Instron universal testing machine. Shear bonding strength and the rate of adhesive failures were recorded. Data were analysed using the analysis of variance (ANOVA), Scheffè tests, and the chi-square test. Uncontaminated enamel surfaces showed the highest bonding strengths for both brackets and buttons. When they were contaminated with blood, orthodontic brackets had significantly lower shear strengths than bondable buttons (P=0.0001). There were significant differences in sites of failure among the groups for the various enamel surfaces (P=0.001). Contamination of enamel by blood during bonding lowers the strength of the bond, more so with orthodontic brackets than with bondable buttons. Copyright © 2010 The British Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

Effect of Pressure and Heat Treatments on the Compressive Strength of Reactive Powder Concrete

Directory of Open Access Journals (Sweden)

Helmi Masdar

2018-01-01

Full Text Available This paper presents the corresponding compressive strength of RPC with variable pressure combined with heating rate, heating duration, and starting time of heating. The treatments applied were 8 MPa static pressure on fresh RPC prims and heat curing at 240 °C in an oven. The compressive strength test was conducted at 7-d and 28-d. The images of RPC morphology were captured on the surface of a fractured specimen using Scanning Electron Microscopy in Secondary Electron detector mode to describe pore filing mechanism after treatments. The results show that a heating rate at 50 °C/hr resulted in the highest compressive strength about 40 % more than those at 10 or 100 °C/hr. A heating duration of 48 hours led to the maximum compressive strength. Heat curing applied 2 days after casting resulted in the maximum compressive. Heat curing had a signicant effect on the compresssive strength due to the acceleration of both reactions (hydration and pozzolanic and the degree of transformation from tobermorite to xonotlite. It is concluded that the optimum condition of treatments is both pressure and heat curing at 2-day after casting with a rate of 50 °C/hr for 48 hours.

THE EFFECT OF THE STATIC RELATIVE STRENGTH ON THE MAXIMUM RELATIVE RECEIVING OF OXYGEN

Directory of Open Access Journals (Sweden)

Abdulla Elezi

2011-09-01

Full Text Available Based on research on the sample of 263 students of age- 18 years, and used batteries of 9 tests for evaluation of the static relative strength and the criterion variable- maximum relative receiving of oxygen (VO2 ml / kg / min based on the Astrand test ,and on regression analysis to determine the influence of the static relative strength on the criterion variable maximum relative oxygen receiving, can be generally concluded that from 9 predictor variables statistically significant partial effect have 2variables. In hierarchical order, they are: the variable of static relative leg strength - endurance of the fingers (the angle of the lower leg and thigh 900 (SRL2 which arithmetic mean is 25.04 seconds and variable ctatic relative strength of arms and shoulders – push-up endurance in the balance beam (angle of the forearm and upper arm 900 ( SRA2 with arithmetic mean of 17.75 seconds. From the statistically influential significant predictor variables on the criterion variable one is from the static relative leg strength (SRL2 and the other is from the static relative strength of arm and shoulder area (SRA2. With the analysis of these relations we can conclude that the isometric contractions of the four headed thigh muscle and the isometric contractions of the three headed upper arm muscle are predominantly responsible for the successful execution of doing actions on a bicycle ergometer and not on the maximum relative receiving of oxygen.

Effects of different crumb rubber sizes on the flowability and compressive strength of hybrid fibre reinforced ECC

Science.gov (United States)

Khed, Veerendrakumar C.; Mohammed, Bashar S.; Fadhil Nuruddin, Muhd

2018-04-01

The different sizes of crumb rubber have been used to investigate the effects on flowability and the compressive strength of the hybrid fibre reinforced engineered cementitious composite. Two sizes of crumb rubber 30 mesh and 1 to 3mm were used in partial replacement with the fine aggregate up to 60%. The experimental study was carried out through mathematical and statistical analysis by response surface methodology (RSM) using the Design Expert software. The response models have been developed and the results were validated by analysis of variance (ANOVA). It was found that finer sized crumb rubber inclusion had produced better workability and higher compressive strength when compared to the larger size and it was concluded that crumb rubber has negative effect on compressive strength and positive effect on workability. The optimization results are found to an approximately good agreement with the experimental results.

Differential effects of arousal in positive and negative autobiographical memories.

Science.gov (United States)

Ford, Jaclyn Hennessey; Addis, Donna Rose; Giovanello, Kelly S

2012-01-01

Autobiographical memories are characterised by a range of emotions and emotional reactions. Recent research has demonstrated that differences in emotional valence (positive vs. negative emotion) and arousal (the degree of emotional intensity) differentially influence the retrieved memory narrative. Although the mnemonic effects of valence and arousal have both been heavily studied, it is currently unclear whether the effects of emotional arousal are equivalent for positive and negative autobiographical events. In the current study, multilevel models were used to examine differential effects of emotional valence and arousal on the richness of autobiographical memory retrieval both between and within subjects. Thirty-four young adults were asked to retrieve personal autobiographical memories associated with popular musical cues and to rate the valence, arousal and richness of these events. The multilevel analyses identified independent influences of valence and intensity upon retrieval characteristics at the within- and between-subject levels. In addition, the within-subject interactions between valence and arousal highlighted differential effects of arousal for positive and negative memories. These findings have important implications for future studies of emotion and memory, highlighting the importance of considering both valence and arousal when examining the role emotion plays in the richness of memory representation.

effect of reinforcements combination on the mechanical strength of ...

African Journals Online (AJOL)

Dr Obe

strength when compared with other metals such as aluminum, copper ... achieved by hand rotation of the wheels as described above. By ratio ... point of the specimen which is recorded by the push-plotter silver liquid indicator. This is the ultimate strength. The Brinnel hardness, Hb is calculated using the Brinnel equation: √.

The Effects of Whole-Body Vibration on the Cross-Transfer of Strength

Directory of Open Access Journals (Sweden)

Alicia M. Goodwill

2012-01-01

Full Text Available This study investigated whether the use of superimposed whole-body vibration (WBV during cross-education strength training would optimise strength transfer compared to conventional cross-education strength training. Twenty-one healthy, dominant right leg volunteers (21±3 years were allocated to a strength training (ST, m=3, f=4, a strength training with WBV (ST + V, m=3, f=4, or a control group (no training, m=3, f=4. Training groups performed 9 sessions over 3 weeks, involving unilateral squats for the right leg, with or without WBV (35 Hz; 2.5 mm amplitude. All groups underwent dynamic single leg maximum strength testing (1RM and single and paired pulse transcranial magnetic stimulation (TMS prior to and following training. Strength increased in the trained limb for the ST (41%; ES=1.14 and ST + V (55%; ES=1.03 groups, which resulted in a 35% (ES=0.99 strength transfer to the untrained left leg for the ST group and a 52% (ES=0.97 strength transfer to the untrained leg for the ST + V group, when compared to the control group. No differences in strength transfer between training groups were observed (P=0.15. For the untrained leg, no differences in the peak height of recruitment curves or SICI were observed between ST and ST + V groups (P=1.00. Strength training with WBV does not appear to modulate the cross-transfer of strength to a greater magnitude when compared to conventional cross-education strength training.

Advanced characterization techniques in understanding the roles of nickel in enhancing strength and toughness of submerged arc welding high strength low alloy steel multiple pass welds in the as-welded condition

Science.gov (United States)

Sham, Kin-Ling

Striving for higher strength along with higher toughness is a constant goal in material properties. Even though nickel is known as an effective alloying element in improving the resistance of a steel to impact fracture, it is not fully understood how nickel enhances toughness. It was the goal of this work to assist and further the understanding of how nickel enhanced toughness and maintained strength in particular for high strength low alloy (HSLA) steel submerged arc welding multiple pass welds in the as-welded condition. Using advanced analytical techniques such as electron backscatter diffraction, x-ray diffraction, electron microprobe, differential scanning calorimetry, and thermodynamic modeling software, the effect of nickel was studied with nickel varying from one to five wt. pct. in increments of one wt. pct. in a specific HSLA steel submerged arc welding multiple pass weldment. The test matrix of five different nickel compositions in the as-welded and stress-relieved condition was to meet the targeted mechanical properties with a yield strength greater than or equal to 85 ksi, a ultimate tensile strength greater than or equal to 105 ksi, and a nil ductility temperature less than or equal to -140 degrees F. Mechanical testing demonstrated that nickel content of three wt. pct and greater in the as-welded condition fulfilled the targeted mechanical properties. Therefore, one, three, and five wt. pct. nickel in the as-welded condition was further studied to determine the effect of nickel on primary solidification mode, nickel solute segregation, dendrite thickness, phase transformation temperatures, effective ferrite grain size, dislocation density and strain, grain misorientation distribution, and precipitates. From one to five wt. pct nickel content in the as-welded condition, the primary solidification was shown to change from primary delta-ferrite to primary austenite. The nickel partitioning coefficient increased and dendrite/cellular thickness was

Investigating Strength and Frequency Effects in Recognition Memory Using Type-2 Signal Detection Theory

Science.gov (United States)

Higham, Philip A.; Perfect, Timothy J.; Bruno, Davide

2009-01-01

Criterion- versus distribution-shift accounts of frequency and strength effects in recognition memory were investigated with Type-2 signal detection receiver operating characteristic (ROC) analysis, which provides a measure of metacognitive monitoring. Experiment 1 demonstrated a frequency-based mirror effect, with a higher hit rate and lower…

Effect of a whitening agent application on enamel bond strength of self-etching primer systems.

Science.gov (United States)

Miyazaki, Masashi; Sato, Hikaru; Sato, Tomomi; Moore, B Keith; Platt, Jeffrey A

2004-06-01

Though reduction in bond strength after tooth whitening has been reported, little is known about it's effect on enamel bond strength of two-step bonding systems that exclude phosphoric acid etching prior to bonding agent application. The purpose of this study was to determine the effect of whitening procedure using an in-office whitening agent on enamel bond strength of self-etching primer systems. Three self-etching primer systems, Imperva Fluoro Bond, Mac Bond II, Clearfil SE Bond, and a one-bottle adhesive system Single Bond as a control material, were used. Bovine mandibular incisors were mounted in self-curing resin and the facial enamel or dentin surfaces were ground wet on 600-grit SiC paper. An in-office whitening agent, Hi-Lite was applied on the tooth surface according to the manufacturer's instruction. Bonding procedures were done soon after rinsing off the whitening agent or after 24 hours storage in distilled water. Specimens without whitening procedure were prepared as controls. Fifteen specimens per test group were stored in 37 degrees C distilled water for 24 hours, then shear tested at a crosshead speed of 1.0 mm/minute. One-way ANOVA followed by Duncan multiple range test were used for statistical analysis of the results. For the specimens made soon after rinsing off the whitening agent, a significant decrease in enamel bond strength was observed for all the bonding systems used. For the specimens made after 24 hours storage in water, a small decrease in enamel bond strength was observed and no significant differences were found compared to those of controls (without whitening). From the results of this study, enamel bond strengths of the self-etching primer systems might be affected to a lesser degree after rinsing with water followed by 24 hours storage in water.

The Effects of Eccentric Contraction Duration on Muscle Strength, Power Production, Vertical Jump, and Soreness.

Science.gov (United States)

Mike, Jonathan N; Cole, Nathan; Herrera, Chris; VanDusseldorp, Trisha; Kravitz, Len; Kerksick, Chad M

2017-03-01

Mike, JN, Cole, N, Herrera, C, VanDusseldorp, T, Kravitz, L, and Kerksick, CM. The effects of eccentric contraction duration on muscle strength, power production, vertical jump, and soreness. J Strength Cond Res 31(3): 773-786, 2017-Previous research has investigated the effects of either eccentric-only training or comparing eccentric and concentric exercise on changes related to strength and power expression, but no research to date has investigated the impact of altering the duration of either the concentric or the eccentric component on these parameters. Therefore, the purpose of this study was to assess the duration of eccentric (i.e., 2-second, 4-second vs. 6-second) muscle contractions and their effect on muscle strength, power production, vertical jump, and soreness using a plate-loaded barbell Smith squat exercise. Thirty college-aged men (23 ± 3.5 years, 178 ± 6.8 cm, 82 ± 12 kg, and 11.6 ± 5.1% fat) with 3.0 ± 1.0 years of resistance training experience and training frequency of 4.3 ± 0.9 days per week were randomized and assigned to 1 of 3 eccentric training groups that incorporated different patterns of contraction. For every repetition, all 3 groups used 2-second concentric contractions and paused for 1 second between the concentric and eccentric phases. The control group (2S) used 2-second eccentric contractions, whereas the 4S group performed 4-second eccentric contractions and the 6S group performed 6-second eccentric contractions. All repetitions were completed using the barbell Smith squat exercise. All participants completed a 4-week training protocol that required them to complete 2 workouts per week using their prescribed contraction routine for 4 sets of 6 repetitions at an intensity of 80-85% one repetition maximum (1RM). For all performance data, significant group × time (G × T) interaction effects were found for average power production across all 3 sets of a squat jump protocol (p = 0.04) while vertical jump did not reach

Effect of municipal solid waste ash on comprehensive strength ...

African Journals Online (AJOL)

The blocks were moulded in a CINVA-Ram machine by replacing 0%, 2%, 5% and 10% of municipal solid waste ash (MSW ash) as a stabilizing agent. The compressive strengths of individual blocks were obtained after curing for 7, 14 and 28 days. The 2%MSW ash replacement gave the highest compressive strength and ...

Effect of curing time on microstructure and mechanical strength ...

Indian Academy of Sciences (India)

The aim of this paper is to study the influence of curing time on the microstructure and mechanical strength development of alkali activated binders based on vitreous calcium aluminosilicate (VCAS). Mechanical strength of alkali activated mortars cured at 65 °C was assessed for different curing times (4–168 h) using 10 ...

Eight Weeks of Phosphatidic Acid Supplementation in Conjunction with Resistance Training Does Not Differentially Affect Body Composition and Muscle Strength in Resistance-Trained Men

Directory of Open Access Journals (Sweden)

Thomas L. Andre, Joshua J. Gann, Sarah K. McKinley-Barnard, Joon J. Song, Darryn S. Willoughby

2016-09-01

Full Text Available This study attempted to determine the effects of eight weeks of resistance training (RT combined with phosphatidic acid (PA supplementation at a dose of either 250 mg or 375 mg on body composition and muscle size and strength. Twenty-eight resistance-trained men were randomly assigned to ingest 375 mg [PA375 (n = 9] or 250 mg [PA250 (n = 9] of PA or 375 mg of placebo [PLC (n = 10] daily for eight weeks with RT. Supplements were ingested 60 minutes prior to RT and in the morning on non-RT days. Participants’ body composition, muscle size, and lower-body muscle strength were determined before and after training/supplementation. Separate group x time ANOVAs for each criterion variable were used employing an alpha level of ≤ 0.05. Magnitude- based inferences were utilized to determine the likely or unlikely impact of PA on each criterion variable. A significant main effect for time was observed for improvements in total body mass (p = 0.003, lean mass (p = 0.008, rectus femoris cross-sectional area [RF CSA (p = 0.011], and lower-body strength (p 0.05. Collectively, magnitude-based inferences determined both doses of PA to have a likely impact of increasing body mass (74.2%, lean mass (71.3%, RF CSA (92.2%, and very likely impact on increasing lower-body strength (98.1% beneficial. When combined with RT, it appears that PA has a more than likely impact on improving lower-body strength, whereas a likely impact exists for increasing muscle size and lean mass.

Effect of some types of machining processes on beryllium fatigue strength properties

International Nuclear Information System (INIS)

Armbruster, M.

1977-01-01

The aim of this work, which is sponsored by the French D.G.R.S.T., is to determine a machining process giving both the highest tensile strength and the highest fatigue limit to beryllium parts. A comparison is made of the effects of : mechanical machining, electro discharge machining, electro-chemical machining, electrolytical and chemical polishing, glass shot peening, on the mechanical strength and fatigue limits of samples taken from hot pressed and extruded rods and from cast ingot sheets, either notched or not as required. Complementary examinations are performed principally by fractographic study. The results show that for beryllium, electrochemical machining followed by glass shot peening gives the best results; however mechanical machining with electrolytical polishing followed by glass shot peening are also satisfactory. (author)

Effects of cathodic protection on cracking of high-strength pipeline steels

Energy Technology Data Exchange (ETDEWEB)

Elboujdaini, M.; Revie, R. W.; Attard, M. [CANMET Materials Technology Laboratory, Ottawa, ON(Canada)], email: melboujd@nrcan.gc.ca

2010-07-01

Four strength levels of pipeline steels, ranging from X-70 to X-120, were compared to determine whether higher strength materials are more susceptible to hydrogen embrittlement under cathodic protection. Ductility was measured in a solution at four protection levels, going from no cathodic protection to 500 mV of overprotection. All four steels showed loss of ductility under cathodic protection. Under cathodic polarization, the loss of ductility increased with the strength of the steel and the activity of the potential. After slow-strain-rate experiments conducted in air and examination of fracture surfaces, it is concluded that application of cathodic potentials, cathodic overprotection, higher strength of steel, and exposure to aqueous solution are factors that decrease the ductility of steel. Hydrogen reduction seems to be an important factor in ductility reduction and fractures. Observations suggest that high-strength pipelines need better control of cathodic protection than lower-strength pipelines.

Effect of Pre-heating on Microtensile Bond Strength of Composite Resin to Dentin.

Directory of Open Access Journals (Sweden)

Abdolrahim Davari

2014-10-01

Full Text Available Direct composite resin restorations are widely used and the impact of different storage temperatures on composites is not well understood. The purpose of this study was to evaluate the microtensile bond strength of composite to dentin after different pre-curing temperatures.Occlusal surfaces of 44 human molars were ground with diamond burs under water coolant and polished with 600 grit silicon carbide papers to obtain flat dentin surfaces. The dentin was etched with 37% phosphoric acid and bonded with Adper Single Bond 2 according to the manufacturer's instructions. The specimens were randomly divided into two groups (n=22 according to the composite resin applied: FiltekP60 and Filtek Z250. Each group included three subgroups of composite resin pre-curing temperatures (4°C, 23°C and 37°C. Composite resins were applied to the dentin surfaces in a plastic mold (8mm in diameter and 4mm in length incrementally and cured. Twenty-two composite-to-dentin hour-glass sticks with one mm(2 cross-sectional area per group were prepared. Microtensile bond strength measurements were made using a universal testing machine at a crosshead speed of one mm/min. For statistical analysis, t-test, one-way and two-way ANOVA were used. The level of significance was set at P<0.05.Filtek P60 pre-heated at 37ºC had significantly higher microtensile bond strength than Filtek Z250 under the same condition. The microtensile bond strengths were not significantly different at 4ºC, 23ºC and 37ºC subgroups of each composite resin group.Filtek P60 and Filtek Z250 did not have significantly different microtensile bond strengths at 4ºC and 23ºC but Filtek P60 had significantly higher microtensile bond strength at 37 ºC. Composite and temperature interactions had significant effects on the bond strength.

The Effect of Body Mass on Eccentric Knee-Flexor Strength Assessed With an Instrumented Nordic Hamstring Device (Nordbord) in Football Players.

Science.gov (United States)

Buchheit, Martin; Cholley, Yannick; Nagel, Mark; Poulos, Nicholas

2016-09-01

To examine the effect of body mass (BM) on eccentric knee-flexor strength using the Nordbord and offer simple guidelines to control for the effect of BM on knee-flexor strength. Data from 81 soccer players (U17, U19, U21, senior 4th French division, and professionals) and 41 Australian Football League (AFL) players were used for analysis. They all performed 1 set of 3 maximal repetitions of the bilateral Nordic hamstring exercise, with the greatest strength measure used for analysis. The main regression equation obtained from the overall sample was used to predict eccentric knee-flexor strength from a given BM (moderate TEE, 22%). Individual deviations from the BM-predicted score were used as a BM-free index of eccentric knee- flexor strength. There was a large (r = .55, 90% confidence limits .42;.64) correlation between eccentric knee-flexor strength and BM. Heavier and older players (professionals, 4th French division, and AFL) outperformed their lighter and younger (U17-U21) counterparts, with the soccer professionals presenting the highest absolute strength. Professional soccer players were the only ones to show strength values likely slightly greater than those expected for their BM. Eccentric knee-flexor strength, as assessed with the Nordbord, is largely BM-dependent. To control for this effect, practitioners may compare actual test performances with the expected strength for a given BM, using the following predictive equation: Eccentric strength (N) = 4 × BM (kg) + 26.1. Professional soccer players with specific knee-flexor-training history and enhanced neuromuscular performance may show higher than expected values.

Effect of microstructure on the cleavage fracture strength of low carbon Mn-Ni-Mo bainitic steels

International Nuclear Information System (INIS)

Im, Young-Roc; Lee, Byeong-Joo; Oh, Yong Jun; Hong, Jun Hwa; Lee, Hu-Chul

2004-01-01

The effects of the microstructure on the cleavage fracture strength of low carbon Mn-Ni-Mo bainitic steels were examined. A four-point bend test and double-notched bend specimens were used to measure the cleavage fracture strength of the alloys and identify the cleavage initiating micro-cracks, respectively. The cleavage fracture strength and DBTT of Mn-Ni-Mo bainitic steels were strongly affected by the alloy carbon content. The decrease in the alloy carbon content resulted in a decrease in the inter-lath cementite-crowded layers and higher cleavage fracture strength. Micro-cracks that formed across the inter-lath cementite-crowded layers were observed to initiate cleavage fracture. The width of these inter-lath cementite-crowded layers was accepted as a cleavage initiating micro-crack size in the micro-mechanical modeling of the cleavage fracture, and the measured cleavage strength values of the bainitic Mn-Ni-Mo steels were well represented by the modified Griffith relationship

Effectiveness of a Brief Intervention Using Process-Based Mental Simulations in Promoting Muscular Strength in Physical Education

Science.gov (United States)

Koka, Andre

2017-01-01

This study examined the effectiveness of a brief theory-based intervention on muscular strength among adolescents in a physical education setting. The intervention adopted a process-based mental simulation technique. The self-reported frequency of practising for and actual levels of abdominal muscular strength/endurance as one component of…

Effect of surface finishing and heat treatments on the mechanical strength of sintered alumina

International Nuclear Information System (INIS)

Lino, U.R.A.

1982-04-01

The effect of surface finishing on the mechanical strength of two pure aluminas, one of self-production and another a commercial one, is studied. Three types of finishings: as-sintered, as machined and as-machined with thermal treatment were studied. It was verified that the as-machined alumina is about 50 percent stronger than the as-sintered one, and that a thermal treatment increases even more the mechanical strength of the sintered alumina. The effect of the volume and pressing direction on mechanical strength was studied. The kinetics of crack healing was determined from a series of systematically selected thermal treatments with annealing temperatures between 1200 0 C and 1600 0 C. It was verified that a recently developed theoretical model for crack healing can describe the experimental results; using this model a value for the activation energy of the process of 715 kJ/mcl was obtained, which suggests that crack healing is promoted by volume diffusion. The material behavior under subcritical crack growth action was also studied, and a value of about 40 for the subcritical crack growth exponent N from dynamic loading tests in water was found. A fractographic study intended to localize and measure the flaws that originated the fracture of the tested specimens was performed; the measured flaw sizes were compared with the flaw size calculated from the values of the measured mechanical strength; in this comparison an excellent agreement was observed. (Author) [pt

Effect of cell density on adipogenic differentiation of mesenchymal stem cells

International Nuclear Information System (INIS)

Lu, Hongxu; Guo, Likun; Wozniak, Michal J.; Kawazoe, Naoki; Tateishi, Tetsuya; Zhang, Xingdong; Chen, Guoping

2009-01-01

The effect of cell density on the adipogenic differentiation of human bone marrow-derived mesenchymal stem cells (MSCs) was investigated by using a patterning technique to induce the formation of a cell density gradient on a micropatterned surface. The adipogenic differentiation of MSCs at a density gradient from 5 x 10 3 to 3 x 10 4 cells/cm 2 was examined. Lipid vacuoles were observed at all cell densities after 1-3 weeks of culture in adipogenic differentiation medium although the lipid vacuoles were scarce at the low cell density and abundant at the high cell density. Real-time RT-PCR analysis showed that adipogenesis marker genes encoding peroxisome proliferator-activated receptor γ2 (PPARγ2), lipoprotein lipase (LPL), and fatty acid binding protein-4 (FABP4) were detected in the MSCs cultured at all cell densities. The results suggest that there was no apparent effect of cell density on the adipogenic differentiation of human MSCs.

Effect of moisture and drying time on the bond strength of the one-step self-etching adhesive system

Directory of Open Access Journals (Sweden)

Yoon Lee

2012-08-01

Full Text Available Objectives To investigate the effect of dentin moisture degree and air-drying time on dentin-bond strength of two different one-step self-etching adhesive systems. Materials and Methods Twenty-four human third molars were used for microtensile bond strength testing of G-Bond and Clearfil S3 Bond. The dentin surface was either blot-dried or air-dried before applying these adhesive agents. After application of the adhesive agent, three different air drying times were evaluated: 1, 5, and 10 sec. Composite resin was build up to 4 mm thickness and light cured for 40 sec with 2 separate layers. Then the tooth was sectioned and trimmed to measure the microtensile bond strength using a universal testing machine. The measured bond strengths were analyzed with three-way ANOVA and regression analysis was done (p = 0.05. Results All three factors, materials, dentin wetness and air drying time, showed significant effect on the microtensile bond strength. Clearfil S3 Bond, dry dentin surface and 10 sec air drying time showed higher bond strength. Conclusions Within the limitation of this experiment, air drying time after the application of the one-step self-etching adhesive agent was the most significant factor affecting the bond strength, followed by the material difference and dentin moisture before applying the adhesive agent.

Testosterone Replacement, Muscle Strength, and Physical Function

Directory of Open Access Journals (Sweden)

You-Seon Nam

2018-05-01

Full Text Available Muscle strength and physical function decrease in older men, as do testosterone levels. Nonetheless, the effects of testosterone replacement therapy on muscle strength and physical function remain inconclusive and equivocal. We conducted a rapid systematic review, the results of which showed that testosterone replacement does not affect muscle strength (measured by hand grip strength and leg muscle strength, although it may increase physical function (measured by the 6-minute walk test, Physical Activity Scale for the Elderly score, and other physical performance tests. However, most of the studies were conducted in the United States or Europe and did not include participants from Asian or other ethnic backgrounds; therefore, further studies are needed to evaluate the effects of testosterone replacement in a broader population.

Thrombopoietin has a differentiative effect on late-stage human erythropoiesis.

Science.gov (United States)

Liu, W; Wang, M; Tang, D C; Ding, I; Rodgers, G P

1999-05-01

To further explore the mechanism of the effect of thrombopoietin (TPO) on erythropoiesis, we used a two-phase culture system to investigate the effect of TPO on late-stage human erythroid lineage differentiation. In serum-free suspension and semisolid cultures of human peripheral blood derived erythroid progenitors, TPO alone did not produce benzidine-positive cells. However, in serum-containing culture, TPO alone stimulated erythroid cell proliferation and differentiation, demonstrated by erythroid colony formation, production of benzidine-positive cells and haemoglobin (Hb) synthesis. Monoclonal anti-human erythropoietin antibody and anti-human erythropoietin receptor antibody completely abrogated the erythroid differentiative ability of TPO in the serum-containing systems. This implied that binding of EPO and EPO-R was essential for erythropoiesis and the resultant signal transduction may be augmented by the signals emanating from TPO-c-Mpl interaction. Experiment of withdrawal of TPO further demonstrated the involvement of TPO in late-stage erythropoiesis. RT-PCR results showed that there was EPO-R but not c-Mpl expression on developing erythroblasts induced by TPO in serum-containing system. Our results establish that TPO affects not only the proliferation of erythroid progenitors but also the differentiation of erythroid progenitors to mature erythroid cells.

Experimental Investigation into Corrosion Effect on Mechanical Properties of High Strength Steel Bars under Dynamic Loadings

Directory of Open Access Journals (Sweden)

Hui Chen

2018-01-01

Full Text Available The tensile behaviors of corroded steel bars are important in the capacity evaluation of corroded reinforced concrete structures. The present paper studies the mechanical behavior of the corroded high strength reinforcing steel bars under static and dynamic loading. High strength reinforcing steel bars were corroded by using accelerated corrosion methods and the tensile tests were carried out under different strain rates. The results showed that the mechanical properties of corroded high strength steel bars were strain rate dependent, and the strain rate effect decreased with the increase of corrosion degree. The decreased nominal yield and ultimate strengths were mainly caused by the reduction of cross-sectional areas, and the decreased ultimate deformation and the shortened yield plateau resulted from the intensified stress concentration at the nonuniform reduction. Based on the test results, reduction factors were proposed to relate the tensile behaviors with the corrosion degree and strain rate for corroded bars. A modified Johnson-Cook strength model of corroded high strength steel bars under dynamic loading was proposed by taking into account the influence of corrosion degree. Comparison between the model and test results showed that proposed model properly describes the dynamic response of the corroded high strength rebars.

The Evaluation of Strength Training and Body Plyometric Effects on the Male Basketball Players

Science.gov (United States)

Bayram, Metin

2016-01-01

This research evaluated the effects of resistance training with upper body plyometric effects on the performance of male basketball players. Sixteen males in the physical education and sport science faculty of Ataturk University were randomly determined into two groups. The experimental group performed a combined strength and plyometric training…

Effect of transition metal impurities on the strength of grain boundaries in vanadium

Energy Technology Data Exchange (ETDEWEB)

Wu, Xuebang; Kong, Xiang-Shan; You, Yu-Wei; Liu, Wei; Liu, C. S., E-mail: csliu@issp.ac.cn [Key Laboratory of Materials Physics, Institute of Solid State Physics, Chinese Academy of Sciences, P.O. Box 1129, Hefei 230031 (China); Chen, Jun-Ling; Luo, G.-N. [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China)

2016-09-07

Effects of 3d (Ti-Ni), 4d (Zr-Pd), and 5d (Hf-Pt) transition metal impurities on strength of two representative vanadium grain boundaries (GBs), symmetric Σ3(111) and asymmetric Σ5(210), were studied by first-principles calculations within the framework of the Rice-Wang thermodynamic model and within the computational tensile test. The desirable elements to increase the GB cohesion were predicted based on their segregation and strengthening behaviors across the different GB sites. It reveals that the elements Ti, Zr, Hf, Nb, and Ta are good choices for the GB cohesion enhancers. In addition, the GB strengthening by solutes is sensitive to the GB structures. The elements Cr, Mn, Fe, Co, and Ni decrease the GB strength of the Σ3(111) GB but they can increase the cohesion of the Σ5(210) GB. Furthermore, the origin of Ti-induced change of the GB strength was uncovered by analyzing the atomic bonds and electronic structures as well as the tensile strength. This work provides a theoretical guidance to screen promising alloying elements in V-based materials with improved resistance to GB decohesion and also helps us to understand the formation mechanism of Ti-rich precipitates in the V-Cr-Ti alloys under neutron or ion irradiation environments.

Effect of roughness and material strength on the mechanical properties of fracture replicas

International Nuclear Information System (INIS)

Wibowo, J.; Amadei, B.; Sture, S.

1995-08-01

This report presents the results of 11 rotary shear tests conducted on replicas of three hollow cylinders of natural fractures with JRC values of 7.7, 9.4 and 12.0. The JRC values were determined from the results of laser profilometer measurements. The replicas were created from gypsum cement. By varying the water-to-gypsum cement ratio from 30 to 45%, fracture replicas with different values of compressive strength (JCS) were created. The rotary shear experiments were performed under constant normal (nominal) stresses ranging between 0.2 and 1.6 MPa. In this report, the shear test results are compared with predictions using Barton's empirical peak shear strength equation. observations during the experiments indicate that only certain parts of the fracture profiles influence fracture shear strength and dilatancy. Under relatively low applied normal stresses, the JCS does not seem to have a significant effect on shear behavior. As an alternative, a new procedure for predicting the shear behavior of fractures was developed. The approach is based on basic fracture properties such as fracture surface profile data and the compressive strength, modulus of elasticity, and Poisson's ratio of the fracture walls. Comparison between predictions and actual shear test results shows that the alternative procedure is a reliable method

Effect of provisional cements on shear bond strength of porcelain laminate veneers.

Science.gov (United States)

Altintas, Subutay Han; Tak, Onjen; Secilmis, Asli; Usumez, Aslihan

2011-08-01

The purpose of this study was to evaluate the effect of three provisional cements and two cleaning techniques on the final bond strength of porcelain laminate veneers. The occlusal third of the crowns of forty molar teeth were sectioned and embedded in autopolymerizing acrylic resin. Dentin surfaces were polished and specimens were randomly divided into four groups (n=10). Provisional restorations were fabricated and two provisional restorations were cemented onto each tooth. Restorations were fixed with one of three different provisional cements: eugenol-free provisional cement (Cavex), calcium hydroxide (Dycal), and light-cured provisional cement (Tempond Clear). Provisional restorations were removed with either a dental explorer and air-water spray, or a cleaning bur (Opticlean). In the control group, provisional restorations were not used on the surfaces of specimens. IPS Empress 2 ceramic discs were luted with a dual-cured resin cement (Panavia F). Shear bond strength was measured using a universal testing machine. Data were statistically analyzed by ANOVA, Tukey's HSD and Dunnett tests. Surfaces were examined by scanning electronic microscopy. Significant differences were found between the control group and both the light-cured provisional cement groups and the eugenol-free provisional cement-cleaning bur group (Pprovisional cement showed the lowest bond strength values. Selection of the provisional cement is an important factor in the ultimate bond strength of the final restoration. Calcium hydroxide provisional cement and cleaning with a dental explorer are advisable.

Effect of Cardiac Rehabilitation on Strength and Balance in Patients after Coronary Artery Bypass Graft

Directory of Open Access Journals (Sweden)

Nahid Nazari

2014-01-01

Full Text Available Background: The most common method for improving the quality of life especially in chronic heart disease is rehabilitation. For increasing the level of knowledge about effect of rehabilitation and its' impression on improving the quality of life in patients. This study evaluates effect of one month cardiac rehabilitation on lower limb strength and the static and dynamic balance of CABG patients. Materials and Methods: This study is based on clinical trial before and after rehabilitation. the exercise protocol lasted for one month, three times per week, each session lasting 1 hour, on 30 male patients in two groups in control (N=15 and experimental group (N=15 after CABG in the centre of rehabilitation in Javad-Alaeme Heart Hospital, Mashhad. The strength of lower limb by chair standing test, the static balance by standing on one leg and dynamic balance by time up and go (TUG test, was evaluated before and after 1 month rehabilitation in training group and detraining in control group. Data were analyzed with SPSS-16 and used t-test analysis (p≤0.054T. Results: The strength of lower limb (p=0.001, static balance (p=0.023 and dynamic balance (p=0.037 increased significantly after one month of cardiac rehabilitation4T. Conclusion: The result of this study indicates that cardiac rehabilitation after coronary artery bypass surgery causes significant increase in strength of lower limb and balance in patients, the more muscle strength is associated with an increase in ability of performing daily activities and so it causes improved quality of life4T.

Effect of Cardiac Rehabilitation on Strength and Balance in Patients after Coronary Artery Bypass Graft

Directory of Open Access Journals (Sweden)

Nahid Nazari

Full Text Available Background: The most common method for improving the quality of life especially in chronic heart disease is rehabilitation. For increasing the level of knowledge about effect of rehabilitation and its' impression on improving the quality of life in patients. This study evaluates effect of one month cardiac rehabilitation on lower limb strength and the static and dynamic balance of CABG patients. Materials and Methods: This study is based on clinical trial before and after rehabilitation. the exercise protocol lasted for one month, three times per week, each session lasting 1 hour, on 30 male patients in two groups in control (N=15 and experimental group (N=15 after CABG in the centre of rehabilitation in Javad-Alaeme Heart Hospital, Mashhad. The strength of lower limb by chair standing test, the static balance by standing on one leg and dynamic balance by time up and go (TUG test, was evaluated before and after 1 month rehabilitation in training group and detraining in control group. Data were analyzed with SPSS-16 and used t-test analysis (p≤0.05.Results: The strength of lower limb (p=0.001, static balance (p=0.023 and dynamic balance (p=0.037 increased significantly after one month of cardiac rehabilitation.Conclusion: The result of this study indicates that cardiac rehabilitation after coronary artery bypass surgery causes significant increase in strength of lower limb and balance in patients, the more muscle strength is associated with an increase in ability of performing daily activities and so it causes improved quality of life.

The effects of cold immersion and hand protection on grip strength.

Science.gov (United States)

Vincent, M J; Tipton, M J

1988-08-01

The maximal voluntary grip strength (MVGS) of male volunteers was examined following a series of five intermittent 2 min cold water (5 degrees C) immersions of the unprotected hand or forearm. MVGS changes due to wearing a protective glove were also investigated. The surface electrical activity over the hand flexor muscles was recorded, as was the skin temperature of the hand and forearm. MVGS decreased significantly (p less than 0.01) following hand immersions (16%) and forearm immersion (13%). The majority of these reductions occurred during the first 2-min period of immersion. The effect of wearing a glove after unprotected hand cooling also produced significant (p less than 0.01) MVGS reductions which averaged 14%. These reductions were in addition to those caused by hand cooling. We conclude that both hand and forearm protection are important for the maintenance of hand-grip strength following cold water immersion.

Combined effects of petrographic and technological parameters on strength of porous coke substance

Energy Technology Data Exchange (ETDEWEB)

Dinel' t, V.M.; Shkoller, M.B.; Stankevich, A.S.; Korchuganova, G.S.

1983-09-01

The proportion of coke in modern blast furnaces has been reduced and at the same time ore burdens have increased. The coke itself now derives from a much wider range of coals. Laboratory tests related to the structural strength of cokes were carried out with charges composed of 14 representative coals. Results showed that vitrinite reflectance and bulk density were the critical parameters, followed by petrographic composition. Increasing bulk density of the charge from 0.6 to 0.9 g/cm/sup 3/ produces coke with a structural strength which counteracts the effects of increasing diversity in both petrography and reflectance in any one charge.

The effect of microstructure of low-alloy spheroidal cast iron on impact strength

Directory of Open Access Journals (Sweden)

T. Szykowny

2010-01-01

Full Text Available The study presents an evaluation of the effect of microstructure of low-alloy spheroidal cast iron on impact strength within the temperature range from –60 to 100°C. Analyses were conducted on one type of cast iron containing 0.51% Cu and 0.72% Ni. Cast iron was austempered or normalized. Values of KCV and static mechanical properties were determined. Structural and fractographic analyses were based on light and scanning microscopy as well as X-ray diffraction. It was found that thermal processing considerably improves impact strength in relation to cast iron after casting. At the same time static mechanical properties are enhanced.

Effect of gold nanoparticles on adipogenic differentiation of human mesenchymal stem cells

International Nuclear Information System (INIS)

Kohl, Yvonne; Gorjup, Erwin; Katsen-Globa, Alisa; Büchel, Claudia; Briesen, Hagen von; Thielecke, Hagen

2011-01-01

Gold nanoparticles are very attractive for biomedical products. However, there is a serious lack of information concerning the biological activity of nanosized gold in human tissue cells. An influence of nanoparticles on stem cells might lead to unforeseen consequences to organ and tissue functions as long as all cells arising from the initial stem cell might be subsequently damaged. Therefore the effect of negatively charged gold nanoparticles (9 and 95 nm), which are certified as reference material for preclinical biomedical research, on the adipogenic differentiation of human mesenchymal stem cells (hMSCs) is investigated here. Bone marrow hMSCs are chosen as differentiation model since bone marrow hMSCs are well characterized and their differentiation into the adipogenic lineage shows clear and easily detectable differentiation. In this study effects of gold nanoparticles on adipogenic differentiation are analyzed regarding fat storage and mitochondrial activity after different exposure times (4–21 days). Using time lapse microscopy the differentiation progress under chronically gold nanoparticle treatment is continuously investigated. In this preliminary study, chronically treatment of adipogenic differentiating hMSCs with gold nanoparticles resulted in a reduced number and size of lipid vacuoles and reduced mitochondrial activity depending on the applied concentration and the surface charge of the particles.

Effect of gold nanoparticles on adipogenic differentiation of human mesenchymal stem cells

Science.gov (United States)

Kohl, Yvonne; Gorjup, Erwin; Katsen-Globa, Alisa; Büchel, Claudia; von Briesen, Hagen; Thielecke, Hagen

2011-12-01

Gold nanoparticles are very attractive for biomedical products. However, there is a serious lack of information concerning the biological activity of nanosized gold in human tissue cells. An influence of nanoparticles on stem cells might lead to unforeseen consequences to organ and tissue functions as long as all cells arising from the initial stem cell might be subsequently damaged. Therefore the effect of negatively charged gold nanoparticles (9 and 95 nm), which are certified as reference material for preclinical biomedical research, on the adipogenic differentiation of human mesenchymal stem cells (hMSCs) is investigated here. Bone marrow hMSCs are chosen as differentiation model since bone marrow hMSCs are well characterized and their differentiation into the adipogenic lineage shows clear and easily detectable differentiation. In this study effects of gold nanoparticles on adipogenic differentiation are analyzed regarding fat storage and mitochondrial activity after different exposure times (4-21 days). Using time lapse microscopy the differentiation progress under chronically gold nanoparticle treatment is continuously investigated. In this preliminary study, chronically treatment of adipogenic differentiating hMSCs with gold nanoparticles resulted in a reduced number and size of lipid vacuoles and reduced mitochondrial activity depending on the applied concentration and the surface charge of the particles.

Effect of tempering time on the ballistic performance of a high strength armour steel

OpenAIRE

Jena, Pradipta Kumar; Senthil P., Ponguru; K., Siva Kumar