Hybrid dual gate ferroelectric memory for multilevel information storage

KAUST Repository

Khan, Yasser; Caraveo-Frescas, Jesus Alfonso; Alshareef, Husam N.

2015-01-01

Here, we report hybrid organic/inorganic ferroelectric memory with multilevel information storage using transparent p-type SnO semiconductor and ferroelectric P(VDF-TrFE) polymer. The dual gate devices include a top ferroelectric field

Heat storage in forest biomass significantly improves energy balance closure particularly during stable conditions

Science.gov (United States)

Lindroth, A.; Mölder, M.; Lagergren, F.

2009-08-01

Temperature measurements in trunks and branches in a mature ca. 100 years-old mixed pine and spruce forest in central Sweden were used to estimate the heat storage in the tree biomass. The estimated heat flux in the sample trees and data on biomass distributions were used to scale up to stand level biomass heat fluxes. The rate of change of sensible and latent heat storage in the air layer below the level of the flux measurements was estimated from air temperature and humidity profile measurements and soil heat flux was estimated from heat flux plates and soil temperature measurements. The fluxes of sensible and latent heat from the forest were measured with an eddy covariance system in a tower. The analysis was made for a two-month period in summer of 1995. The tree biomass heat flux was the largest of the estimated storage components and varied between 40 and -35 W m-2 on summer days with nice weather. Averaged over two months the diurnal maximum of total heat storage was 45 W m-2 and the minimum was -35 W m-2. The soil heat flux and the sensible heat storage in air were out of phase with the biomass flux and they reached maximum values that were about 75% of the maximum of the tree biomass heat storage. The energy balance closure improved significantly when the total heat storage was added to the turbulent fluxes. The slope of a regression line with sum of fluxes and storage as independent and net radiation as dependent variable, increased from 0.86 to 0.95 for half-hourly data and the scatter was also reduced. The most significant finding was, however, that during nights with strongly stable conditions when the sensible heat flux dropped to nearly zero, the total storage matched the net radiation nearly perfectly. Another interesting result was that the mean energy imbalance started to increase when the Richardson number became more negative than ca. -0.1. In fact, the largest energy deficit occurred at maximum instability. Our conclusion is that eddy

10 CFR 95.25 - Protection of National Security Information and Restricted Data in storage.

Science.gov (United States)

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Protection of National Security Information and Restricted Data in storage. 95.25 Section 95.25 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) FACILITY SECURITY... Protection of National Security Information and Restricted Data in storage. (a) Secret matter, while...

Information Storage and Management Storing, Managing, and Protecting Digital Information in Classic, Virtualized, and Cloud Environments

CERN Document Server

Services, EMC Education

2012-01-01

The new edition of a bestseller, now revised and update throughout! This new edition of the unparalleled bestseller serves as a full training course all in one and as the world's largest data storage company, EMC is the ideal author for such a critical resource. They cover the components of a storage system and the different storage system models while also offering essential new material that explores the advances in existing technologies and the emergence of the "Cloud" as well as updates and vital information on new technologies. Features a separate section on emerging area of cloud computi

Hanford Site Waste Storage Tank Information Notebook

International Nuclear Information System (INIS)

Husa, E.I.; Raymond, R.E.; Welty, R.K.; Griffith, S.M.; Hanlon, B.M.; Rios, R.R.; Vermeulen, N.J.

1993-07-01

This report provides summary data on the radioactive waste stored in underground tanks in the 200 East and West Areas at the Hanford Site. The summary data covers each of the existing 161 Series 100 underground waste storage tanks (500,000 gallons and larger). It also contains information on the design and construction of these tanks. The information in this report is derived from existing reports that document the status of the tanks and their materials. This report also contains interior, surface photographs of each of the 54 Watch List tanks, which are those tanks identified as Priority I Hanford Site Tank Farm Safety Issues in accordance with Public Law 101-510, Section 3137*

Design of an indigeous music information storage and retrieval ...

African Journals Online (AJOL)

The main aim of the study was to design an appropriate Indigenous Music Information Storage and Retrieval System for Eritrea. A quantitative approach was mainly used to obtain data from a purposefully selected sample. The qualitative approach was also used in some research stages. Methods used included document

Weighty data: importance information influences estimated weight of digital information storage devices.

Directory of Open Access Journals (Sweden)

Iris eSchneider

2015-01-01

Full Text Available Previous work has suggested that perceived importance of an object influences estimates of its weight. Specifically, important books were estimated to be heavier than non-important books. However, the experimental set-up of these studies may have suffered from a potential confound and findings may be confined to books only. Addressing this, we investigate the effect of importance on weight estimates by examining whether the importance of information stored on a data storage device (USB-stick or portable hard drive can alter weight estimates. Results show that people thinking a USB-stick holds important tax information (vs. expired vs. no information estimate it to be heavier (Experiment 1 compared to people who do not. Similarly, people who are told a portable hard-drive holds personally relevant information (vs. irrelevant, also estimate the drive to be heavier (Experiment 2a and 2b. The current work shows that importance influences weight perceptions beyond specific objects.

Final environmental assessment and Finding-of-No-Significant-Impact - drum storage facility for interim storage of materials generated by environmental restoration operations

International Nuclear Information System (INIS)

1994-09-01

The Department of Energy (DOE) has prepared an Environmental Assessment (EA), DOE/EA-0995, for the construction and operation of a drum storage facility at Rocky Flats Environmental Technology Site, Golden, Colorado. The proposal for construction of the facility was generated in response to current and anticipated future needs for interim storage of waste materials generated by environmental restoration operations. A public meeting was held on July 20, 1994, at which the scope and analyses of the EA were presented. The scope of the EA included evaluation of alternative methods of storage, including no action. A comment period from July 5, 1994 through August 4, 1994, was provided to the public and the State of Colorado to submit written comment on the EA. No written comments were received regarding this proposed action, therefore no comment response is included in the Final EA. Based on the analyses in the EA, DOE has determined that the proposed action would not significantly affect the quality of the human environment within the meaning of the National Environmental Policy Act of 1969 (NEPA). Therefore, preparation of an Environmental Impact Statement is not required and the Department is issuing this Finding of No Significant Impact

Rocky Mountain Regional CO{sub 2} Storage Capacity and Significance

Energy Technology Data Exchange (ETDEWEB)

Laes, Denise; Eisinger, Chris; Esser, Richard; Morgan, Craig; Rauzi, Steve; Scholle, Dana; Matthews, Vince; McPherson, Brian

2013-08-30

The purpose of this study includes extensive characterization of the most promising geologic CO{sub 2} storage formations on the Colorado Plateau, including estimates of maximum possible storage capacity. The primary targets of characterization and capacity analysis include the Cretaceous Dakota Formation, the Jurassic Entrada Formation and the Permian Weber Formation and their equivalents in the Colorado Plateau region. The total CO{sub 2} capacity estimates for the deep saline formations of the Colorado Plateau region range between 9.8 metric GT and 143 metric GT, depending on assumed storage efficiency, formations included, and other factors.

National Waste Terminal Storage Program information meeting, December 7-8, 1976

International Nuclear Information System (INIS)

1976-01-01

Volume II of the report comprises copies of the slides from the talks presented at the second session of the National Waste Terminal Storage Program information meeting. This session was devoted to geologic studies

Conceptual design report: Nuclear materials storage facility renovation. Part 3, Supplemental information

International Nuclear Information System (INIS)

1995-01-01

The Nuclear Materials Storage Facility (NMSF) at the Los Alamos National Laboratory (LANL) was a Fiscal Year (FY) 1984 line-item project completed in 1987 that has never been operated because of major design and construction deficiencies. This renovation project, which will correct those deficiencies and allow operation of the facility, is proposed as an FY 97 line item. The mission of the project is to provide centralized intermediate and long-term storage of special nuclear materials (SNM) associated with defined LANL programmatic missions and to establish a centralized SNM shipping and receiving location for Technical Area (TA)-55 at LANL. Based on current projections, existing storage space for SNM at other locations at LANL will be loaded to capacity by approximately 2002. This will adversely affect LANUs ability to meet its mission requirements in the future. The affected missions include LANL's weapons research, development, and testing (WRD ampersand T) program; special materials recovery; stockpile survelliance/evaluation; advanced fuels and heat sources development and production; and safe, secure storage of existing nuclear materials inventories. The problem is further exacerbated by LANL's inability to ship any materials offsite because of the lack of receiver sites for mate rial and regulatory issues. Correction of the current deficiencies and enhancement of the facility will provide centralized storage close to a nuclear materials processing facility. The project will enable long-term, cost-effective storage in a secure environment with reduced radiation exposure to workers, and eliminate potential exposures to the public. It is organized into seven parts. Part I - Design Concept describes the selected solution. Part III - Supplemental Information contains calculations for the various disciplines as well as other supporting information and analyses

Method of bistable optical information storage using antiferroelectric phase PLZT ceramics

Science.gov (United States)

Land, Cecil E.

1990-01-01

A method for bistable storage of binary optical information includes an antiferroelectric (AFE) lead lanthanum zirconate titanate (PLZT) layer having a stable antiferroelectric first phase and a ferroelectric (FE) second phase obtained by applying a switching electric field across the surface of the device. Optical information is stored by illuminating selected portions of the layer to photoactivate an FE to AFE transition in those portions. Erasure of the stored information is obtained by reapplying the switching field.

Health information management using optical storage technology: case studies.

Science.gov (United States)

Kohn, D

1992-05-01

All the health care facilities examined in the case studies addressed several important organizational issues before and during the installation of their systems. All the facilities examined employee commitment. The prudent managers considered how easily their employees adapt to changes in their jobs and work environment. They considered how enthusiastic cooperation can be fostered in the creation of a liberated and reengineered office. This was determined not only by each individual's reaction to change, but also by the health care facility's track record with other system installations. For example, document image, diagnostic image, and coded data processing systems allow the integration of divergent health care information systems within complex institutions. Unfortunately, many institutions are currently struggling with how to create an information management architecture that will integrate their mature systems, such as their patient care and financial systems. Information managers must realize that if optical storage technology-based systems are used in a strategic and planned fashion, these systems can act as focal points for systems integration, not as promises to further confuse the issue. Another issue that needed attention in all the examples was the work environment. The managers considered how the work environment was going to affect the ability to integrate optical image and data systems into the institution. For example, many of these medical centers have created alliances with clinics, HMOs, and large corporate users of medical services. This created a demand for all or part of the health information outside the confines of the original institution. Since the work environment is composed of a handful of factors such as merged medical services, as many work environment factors as possible were addressed before application of the optical storage technology solution in the institutions. And finally, the third critical issue was the organization of work

Templated assembly of photoswitches significantly increases the energy-storage capacity of solar thermal fuels.

Science.gov (United States)

Kucharski, Timothy J; Ferralis, Nicola; Kolpak, Alexie M; Zheng, Jennie O; Nocera, Daniel G; Grossman, Jeffrey C

2014-05-01

Large-scale utilization of solar-energy resources will require considerable advances in energy-storage technologies to meet ever-increasing global energy demands. Other than liquid fuels, existing energy-storage materials do not provide the requisite combination of high energy density, high stability, easy handling, transportability and low cost. New hybrid solar thermal fuels, composed of photoswitchable molecules on rigid, low-mass nanostructures, transcend the physical limitations of molecular solar thermal fuels by introducing local sterically constrained environments in which interactions between chromophores can be tuned. We demonstrate this principle of a hybrid solar thermal fuel using azobenzene-functionalized carbon nanotubes. We show that, on composite bundling, the amount of energy stored per azobenzene more than doubles from 58 to 120 kJ mol(-1), and the material also maintains robust cyclability and stability. Our results demonstrate that solar thermal fuels composed of molecule-nanostructure hybrids can exhibit significantly enhanced energy-storage capabilities through the generation of template-enforced steric strain.

Conceptual design report: Nuclear materials storage facility renovation. Part 3, Supplemental information

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-14

The Nuclear Materials Storage Facility (NMSF) at the Los Alamos National Laboratory (LANL) was a Fiscal Year (FY) 1984 line-item project completed in 1987 that has never been operated because of major design and construction deficiencies. This renovation project, which will correct those deficiencies and allow operation of the facility, is proposed as an FY 97 line item. The mission of the project is to provide centralized intermediate and long-term storage of special nuclear materials (SNM) associated with defined LANL programmatic missions and to establish a centralized SNM shipping and receiving location for Technical Area (TA)-55 at LANL. Based on current projections, existing storage space for SNM at other locations at LANL will be loaded to capacity by approximately 2002. This will adversely affect LANUs ability to meet its mission requirements in the future. The affected missions include LANL`s weapons research, development, and testing (WRD&T) program; special materials recovery; stockpile survelliance/evaluation; advanced fuels and heat sources development and production; and safe, secure storage of existing nuclear materials inventories. The problem is further exacerbated by LANL`s inability to ship any materials offsite because of the lack of receiver sites for mate rial and regulatory issues. Correction of the current deficiencies and enhancement of the facility will provide centralized storage close to a nuclear materials processing facility. The project will enable long-term, cost-effective storage in a secure environment with reduced radiation exposure to workers, and eliminate potential exposures to the public. It is organized into seven parts. Part I - Design Concept describes the selected solution. Part III - Supplemental Information contains calculations for the various disciplines as well as other supporting information and analyses.

National Storage Laboratory: a collaborative research project

Science.gov (United States)

Coyne, Robert A.; Hulen, Harry; Watson, Richard W.

1993-01-01

The grand challenges of science and industry that are driving computing and communications have created corresponding challenges in information storage and retrieval. An industry-led collaborative project has been organized to investigate technology for storage systems that will be the future repositories of national information assets. Industry participants are IBM Federal Systems Company, Ampex Recording Systems Corporation, General Atomics DISCOS Division, IBM ADSTAR, Maximum Strategy Corporation, Network Systems Corporation, and Zitel Corporation. Industry members of the collaborative project are funding their own participation. Lawrence Livermore National Laboratory through its National Energy Research Supercomputer Center (NERSC) will participate in the project as the operational site and provider of applications. The expected result is the creation of a National Storage Laboratory to serve as a prototype and demonstration facility. It is expected that this prototype will represent a significant advance in the technology for distributed storage systems capable of handling gigabyte-class files at gigabit-per-second data rates. Specifically, the collaboration expects to make significant advances in hardware, software, and systems technology in four areas of need, (1) network-attached high performance storage; (2) multiple, dynamic, distributed storage hierarchies; (3) layered access to storage system services; and (4) storage system management.

Aflatoxins & Safe Storage

Directory of Open Access Journals (Sweden)

Philippe eVillers

2014-04-01

Full Text Available The paper examines both field experience and research on the prevention of the exponential growth of aflatoxins during multi-month post harvest storage in hot, humid countries. The approach described is the application of modern safe storage methods using flexible, Ultra Hermetic™ structures that create an unbreatheable atmosphere through insect and microorganism respiration alone, without use of chemicals, fumigants, or pumps. Laboratory and field data are cited and specific examples are given describing the uses of Ultra Hermetic storage to prevent the growth of aflatoxins with their significant public health consequences. Also discussed is the presently limited quantitative information on the relative occurrence of excessive levels of aflatoxin (>20 ppb before versus after multi-month storage of such crops as maize, rice and peanuts when under high humidity, high temperature conditions and, consequently, the need for further research to determine the frequency at which excessive aflatoxin levels are reached in the field versus after months of post-harvest storage. The significant work being done to reduce aflatoxin levels in the field is mentioned, as well as its probable implications on post harvest storage. Also described is why, with some crops such as peanuts, using Ultra Hermetic storage may require injection of carbon dioxide or use of an oxygen absorber as an accelerant. The case of peanuts is discussed and experimental data is described.

Forming of information support for estimate of potential danger of storage points of the decontamination wastes

International Nuclear Information System (INIS)

Skurat, V.V.; Shiryaeva, N.M.; Myshkina, N.K.; Gvozdev, A.A.; Serebryannyj, G.Z.; Golikova, N.B.

2002-01-01

By now 92 storage points of the decontamination wastes that formed in result of decontamination of settlements after the Chernobyl accident is registered on the territory of Belarus. The most of theirs were placed in the unfavorable for storage of radioactive wastes places. It was examine the forming of information support for estimate of potential danger of the storage points of decontamination wastes that base on results of investigations of objects, field and laboratory investigations, theoretical researches, using of literary information about features of radionuclides migration through engineering and natural barriers to water-bearing horizon is examination

Communication of technical information to lay audiences. [National Waste Terminal Storage (NWTS) program

Energy Technology Data Exchange (ETDEWEB)

Bowes, J.E.; Stamm, K.R.; Jackson, K.M.; Moore, J.

1978-05-01

One of the objectives of the National Waste Terminal Storage (NWTS) Program is to provide terminal storage facilities for commercial radioactive wastes in various geologic formations at multiple locations in the United States. The activities performed under the NWTS Program will affect regional, state, and local areas, and widespread public interest in this program is expected. Since a large part of the NWTS Program deals with technical information it was considered desirable to initiate a study dealing with possible methods of effectively transmitting this technical information to the general public. This study has the objective of preparing a state-of-the-art report on the communication of technical information to lay audiences. The particular task of communicating information about the NWTS Program to the public is discussed where appropriate. The results of this study will aid the NWTS Program in presenting to the public the quite diverse technical information generated within the program so that a widespread, thorough public understanding of the NWTS Program might be achieved. An annotated bibliography is included.

[Wound information management system: a standardized scheme for acquisition, storage and management of wound information].

Science.gov (United States)

Liu, Hu; Su, Rong-jia; Wu, Min-jie; Zhang, Yi; Qiu, Xiang-jun; Feng, Jian-gang; Xie, Ting; Lu, Shu-liang

2012-06-01

To form a wound information management scheme with objectivity, standardization, and convenience by means of wound information management system. A wound information management system was set up with the acquisition terminal, the defined wound description, the data bank, and related softwares. The efficacy of this system was evaluated in clinical practice. The acquisition terminal was composed of the third generation mobile phone and the software. It was feasible to get access to the wound information, including description, image, and therapeutic plan from the data bank by mobile phone. During 4 months, a collection of a total of 232 wound treatment information was entered, and accordingly standardized data of 38 patients were formed automatically. This system can provide standardized wound information management by standardized techniques of acquisition, transmission, and storage of wound information. It can be used widely in hospitals, especially primary medical institutions. Data resource of the system makes it possible for epidemiological study with large sample size in future.

New infrared-sensitive photopolymer materials for information storage and processing

Science.gov (United States)

Nagtegaele, Patrice; Galstian, Tigran V.

2001-11-01

In response to the increasing demand of information systems, we need new materials with high performance for storage and processing applications. Available on the market optical storage materials present very useful characteristics but are still limited in the visible spectrum and are expansive. Recently, we have developed holographic polymer dispersed liquid crystal (H-PDLC) materials sensitive in the near infrared region (800 nm to 850 nm). These compounds are based on acrylate monomers and different liquid crystals (LC) and allow highly efficient in-situ recording of holographic optical elements using infra red lasers. Diffraction efficiency above 95% is demonstrated. Photosensitivity of the material, its dark ­development and photochemical stability of recorded gratings are investigated. The angular and spectral selectivities of gratings, recorded in these films are examined for recovering the refractive index modulation profile.

Proceedings of the 1982 National Waste Terminal Storage Program information meeting

International Nuclear Information System (INIS)

1982-12-01

The substantial progress made during fiscal year 1982 in the programmatic work directed toward providing the nation with at least one licensed, fully operational mined geologic repository as early as 1998 is given in these papers at the 1982 National Waste Terminal Storage (NWTS) information meeting. Individual papers are indexed. (DP)

Thermal energy storage apparatus, controllers and thermal energy storage control methods

Science.gov (United States)

Hammerstrom, Donald J.

2016-05-03

Thermal energy storage apparatus, controllers and thermal energy storage control methods are described. According to one aspect, a thermal energy storage apparatus controller includes processing circuitry configured to access first information which is indicative of surpluses and deficiencies of electrical energy upon an electrical power system at a plurality of moments in time, access second information which is indicative of temperature of a thermal energy storage medium at a plurality of moments in time, and use the first and second information to control an amount of electrical energy which is utilized by a heating element to heat the thermal energy storage medium at a plurality of moments in time.

Method and apparatus for bistable optical information storage for erasable optical disks

Science.gov (United States)

Land, Cecil E.; McKinney, Ira D.

1990-01-01

A method and an optical device for bistable storage of optical information, together with reading and erasure of the optical information, using a photoactivated shift in a field dependent phase transition between a metastable or a bias-stabilized ferroelectric (FE) phase and a stable antiferroelectric (AFE) phase in an lead lanthanum zirconate titanate (PLZT). An optical disk contains the PLZT. Writing and erasing of optical information can be accomplished by a light beam normal to the disk. Reading of optical information can be accomplished by a light beam at an incidence angle of 15 to 60 degrees to the normal of the disk.

Long-term sera storage does not significantly modify the interpretation of toxoplasmosis serologies.

Science.gov (United States)

Dard, C; Bailly, S; Drouet, T; Fricker-Hidalgo, H; Brenier-Pinchart, M P; Pelloux, H

2017-03-01

Serological investigation of Toxoplasma gondii can answer many questions about toxoplasmosis in human pathology. Along these lines, studies on serum storage in biobanks need to be performed especially in terms of determining the impact of storage on relevance of sera analysis after freezing. This study assessed the impact of long-term sera storage on the stability of anti-Toxoplasma immunoglobulins. The stability of anti-Toxoplasma IgG and IgM was studied in 244 and 242 sera respectively, stored at -20°C from one month to ten years. ELISA-immunoassay (Vidas®, bioMérieux) was used for initial and post-storage analyses. Linear models for repeated measures and subgroup analyses were performed to assess the effect of storage duration and sample characteristics on immunoglobulins stability. Until ten years, the variability attributed to storage (maximum 8.07% for IgG, 13.17% for IgM) was below the variations inherent to the serological technique and allowed by quality assurance systems (15%). Subgroup analysis reported no variation attributed to sera storage. Serological interpretation was modified for 3 sera (1.2%) tested for IgM, all stored more than seven years. Anti-Toxoplasma immunoglobulins can reliably be measured for at least up to six years of storage with no modification of interpretation of toxoplasmosis serologies. Copyright © 2017 Elsevier B.V. All rights reserved.

National Waste Terminal Storage Program information meeting, December 7-8, 1976

International Nuclear Information System (INIS)

1976-12-01

Volume I of the report comprises copies of the slides from the talks presented at the first session of the National Waste Terminal Storage Program information meeting. The agenda for the first day included an overview of the program plus presentations on such subjects as schedules and controls, facility projects, systems studies, regulatory affairs and technical support

An information management system for a spent nuclear fuel interim storage facility

International Nuclear Information System (INIS)

Horak, K.; Giles, T.; Finch, R.; Jow, H.N.; Chiu, H.L.

2010-01-01

We describe an integrated information management system for an independent spent fuel dry-storage installation (ISFSI) that can provide for (1) secure and authenticated data collection, (2) data analysis, (3) dissemination of information to appropriate stakeholders via a secure network, and (4) increased public confidence and support of the facility licensing and operation through increased transparency. This information management system is part of a collaborative project between Sandia National Laboratories, Taiwan Power Co., and the Fuel Cycle Materials Administration of Taiwan's Atomic Energy Council, which is investigating how to implement this concept.

An information management system for a spent nuclear fuel interim storage facility.

Energy Technology Data Exchange (ETDEWEB)

Finch, Robert J.; Chiu, Hsien-Lang (Taiwan Power Co., Taipei, 10016 Taiwan); Giles, Todd; Horak, Karl Emanuel; Jow, Hong-Nian (Jow International, Kirkland, WA)

2010-12-01

We describe an integrated information management system for an independent spent fuel dry-storage installation (ISFSI) that can provide for (1) secure and authenticated data collection, (2) data analysis, (3) dissemination of information to appropriate stakeholders via a secure network, and (4) increased public confidence and support of the facility licensing and operation through increased transparency. This information management system is part of a collaborative project between Sandia National Laboratories, Taiwan Power Co., and the Fuel Cycle Materials Administration of Taiwan's Atomic Energy Council, which is investigating how to implement this concept.

Mental Schemas Hamper Memory Storage of Goal-Irrelevant Information.

Science.gov (United States)

Sweegers, C C G; Coleman, G A; van Poppel, E A M; Cox, R; Talamini, L M

2015-01-01

Mental schemas exert top-down control on information processing, for instance by facilitating the storage of schema-related information. However, given capacity-limits and competition in neural network processing, schemas may additionally exert their effects by suppressing information with low momentary relevance. In particular, when existing schemas suffice to guide goal-directed behavior, this may actually reduce encoding of the redundant sensory input, in favor of gaining efficiency in task performance. The present experiment set out to test this schema-induced shallow encoding hypothesis. Our approach involved a memory task in which faces had to be coupled to homes. For half of the faces the responses could be guided by a pre-learned schema, for the other half of the faces such a schema was not available. Memory storage was compared between schema-congruent and schema-incongruent items. To characterize putative schema effects, memory was assessed both with regard to visual details and contextual aspects of each item. The depth of encoding was also assessed through an objective neural measure: the parietal old/new ERP effect. This ERP effect, observed between 500-800 ms post-stimulus onset, is thought to reflect the extent of recollection: the retrieval of a vivid memory, including various contextual details from the learning episode. We found that schema-congruency induced substantial impairments in item memory and even larger ones in context memory. Furthermore, the parietal old/new ERP effect indicated higher recollection for the schema-incongruent than the schema-congruent memories. The combined findings indicate that, when goals can be achieved using existing schemas, this can hinder the in-depth processing of novel input, impairing the formation of perceptually detailed and contextually rich memory traces. Taking into account both current and previous findings, we suggest that schemas can both positively and negatively bias the processing of sensory input

A monitored retrievable storage facility: Technical background information

International Nuclear Information System (INIS)

1991-07-01

The US government is seeking a site for a monitored retrievable storage facility (MRS). Employing proven technologies used in this country and abroad, the MRS will be an integral part of the federal system for safe and permanent disposal of the nation's high-level radioactive wastes. The MRS will accept shipments of spent fuel from commercial nuclear power plants, temporarily store the spent fuel above ground, and stage shipments of it to a geologic repository for permanent disposal. The law authorizing the MRS provides an opportunity for a state or an Indian tribe to volunteer to host the MRS. The law establishes the Office of the Nuclear Waste Negotiator, who is to seek a state or an Indian tribe willing to host an MRS at a technically-qualified site on reasonable terms, and is to negotiate a proposed agreement specifying the terms and conditions under which the MRS would be developed and operated at that site. This agreement can ensure that the MRS is acceptable to -- and benefits -- the host community. The proposed agreement must be submitted to Congress and enacted into law to become effective. This technical background information presents an overview of various aspects of a monitored retrievable storage facility, including the process by which it will be developed

Carbon-tuned bonding method significantly enhanced the hydrogen storage of BN-Li complexes.

Science.gov (United States)

Deng, Qing-ming; Zhao, Lina; Luo, You-hua; Zhang, Meng; Zhao, Li-xia; Zhao, Yuliang

2011-11-01

Through first-principles calculations, we found doping carbon atoms onto BN monolayers (BNC) could significantly strengthen the Li bond on this material. Unlike the weak bond strength between Li atoms and the pristine BN layer, it is observed that Li atoms are strongly hybridized and donate their electrons to the doped substrate, which is responsible for the enhanced binding energy. Li adsorbed on the BNC layer can serve as a high-capacity hydrogen storage medium, without forming clusters, which can be recycled at room temperature. Eight polarized H(2) molecules are attached to two Li atoms with an optimal binding energy of 0.16-0.28 eV/H(2), which results from the electrostatic interaction of the polarized charge of hydrogen molecules with the electric field induced by positive Li atoms. This practical carbon-tuned BN-Li complex can work as a very high-capacity hydrogen storage medium with a gravimetric density of hydrogen of 12.2 wt%, which is much higher than the gravimetric goal of 5.5 wt % hydrogen set by the U.S. Department of Energy for 2015.

National Waste Terminal Storage Program Information Management Plan. Volume I. Management summary

International Nuclear Information System (INIS)

1977-05-01

A comprehensive information management plan is needed for the processing of the large amount of documentation that will accumulate in the National Waste Terminal Storage program over the next decade. The plan will apply to all documentation from OWI contractors, subcontractors, and suppliers, and to external documentation from OWI organizations

The essential component in DNA-based information storage system: robust error-tolerating module

Directory of Open Access Journals (Sweden)

Aldrin Kay-Yuen eYim

2014-11-01

Full Text Available The size of digital data is ever increasing and is expected to grow to 40,000EB by 2020, yet the estimated global information storage capacity in 2011 is less than 300EB, indicating that most of the data are transient. DNA, as a very stable nano-molecule, is an ideal massive storage device for long-term data archive. The two most notable illustrations are from Church et al. and Goldman et al., whose approaches are well-optimized for most sequencing platforms – short synthesized DNA fragments without homopolymer. Here we suggested improvements on error handling methodology that could enable the integration of DNA-based computational process, e.g. algorithms based on self-assembly of DNA. As a proof of concept, a picture of size 438 bytes was encoded to DNA with Low-Density Parity-Check error-correction code. We salvaged a significant portion of sequencing reads with mutations generated during DNA synthesis and sequencing and successfully reconstructed the entire picture. A modular-based programming framework - DNAcodec with a XML-based data format was also introduced. Our experiments demonstrated the practicability of long DNA message recovery with high error-tolerance, which opens the field to biocomputing and synthetic biology.

Manche storage Centre. Information report on nuclear safety and radiation protection 2015

International Nuclear Information System (INIS)

2016-01-01

After a presentation of the Manche Storage Centre (CSM), the first French center of surface storage of low- and intermediate-level radioactive wastes, of its history, its buildings and activities, of the multi-layer cover, of the water management system (installation, controls, sampling), this report then describes the measures related to nuclear safety, the management of conventional and nuclear wastes produced by the Centre, the other impacts, the control, maintenance and follow-up of installations, the radiation protection and security of the center, the incidents and accidents that occurred at the facility, and the public information and communication actions. Recommendations of the Health and safety Committee (CHSCT) are reported at the end

Survey of experience with dry storage of spent nuclear fuel and update of wet storage experience

International Nuclear Information System (INIS)

1988-01-01

Spent fuel storage is an important part of spent fuel management. At present about 45,000 t of spent water reactor fuel have been discharged worldwide. Only a small fraction of this fuel (approximately 7%) has been reprocessed. The amount of spent fuel arisings will increase significantly in the next 15 years. Estimates indicate that up to the year 2000 about 200,000 t HM of spent fuel could be accumulated. In view of the large quantities of spent fuel discharged from nuclear power plants and future expected discharges, many countries are involved in the construction of facilities for the storage of spent fuel and in the development of effective methods for spent fuel surveillance and monitoring to ensure that reliable and safe operation of storage facilities is achievable until the time when the final disposal of spent fuel or high level wastes is feasible. The first demonstrations of final disposal are not expected before the years 2000-2020. This is why the long term storage of spent fuel and HLW is a vital problem for all countries with nuclear power programmes. The present survey contains data on dry storage and recent information on wet storage, transportation, rod consolidation, etc. The main aim is to provide spent fuel management policy making organizations, designers, scientists and spent fuel storage facility operators with the latest information on spent fuel storage technology under dry and wet conditions and on innovations in this field. Refs, figs and tabs

CHEMICAL STORAGE: MYTHS VERSUS REALITY

International Nuclear Information System (INIS)

Simmons, F.

2007-01-01

A large number of resources explaining proper chemical storage are available. These resources include books, databases/tables, and articles that explain various aspects of chemical storage including compatible chemical storage, signage, and regulatory requirements. Another source is the chemical manufacturer or distributor who provides storage information in the form of icons or color coding schemes on container labels. Despite the availability of these resources, chemical accidents stemming from improper storage, according to recent reports (1) (2), make up almost 25% of all chemical accidents. This relatively high percentage of chemical storage accidents suggests that these publications and color coding schemes although helpful, still provide incomplete information that may not completely mitigate storage risks. This manuscript will explore some ways published storage information may be incomplete, examine the associated risks, and suggest methods to help further eliminate chemical storage risks

Neural mechanisms of information storage in visual short-term memory.

Science.gov (United States)

Serences, John T

2016-11-01

The capacity to briefly memorize fleeting sensory information supports visual search and behavioral interactions with relevant stimuli in the environment. Traditionally, studies investigating the neural basis of visual short term memory (STM) have focused on the role of prefrontal cortex (PFC) in exerting executive control over what information is stored and how it is adaptively used to guide behavior. However, the neural substrates that support the actual storage of content-specific information in STM are more controversial, with some attributing this function to PFC and others to the specialized areas of early visual cortex that initially encode incoming sensory stimuli. In contrast to these traditional views, I will review evidence suggesting that content-specific information can be flexibly maintained in areas across the cortical hierarchy ranging from early visual cortex to PFC. While the factors that determine exactly where content-specific information is represented are not yet entirely clear, recognizing the importance of task-demands and better understanding the operation of non-spiking neural codes may help to constrain new theories about how memories are maintained at different resolutions, across different timescales, and in the presence of distracting information. Copyright © 2016 Elsevier Ltd. All rights reserved.

Neural Mechanisms of Information Storage in Visual Short-Term Memory

Science.gov (United States)

Serences, John T.

2016-01-01

The capacity to briefly memorize fleeting sensory information supports visual search and behavioral interactions with relevant stimuli in the environment. Traditionally, studies investigating the neural basis of visual short term memory (STM) have focused on the role of prefrontal cortex (PFC) in exerting executive control over what information is stored and how it is adaptively used to guide behavior. However, the neural substrates that support the actual storage of content-specific information in STM are more controversial, with some attributing this function to PFC and others to the specialized areas of early visual cortex that initially encode incoming sensory stimuli. In contrast to these traditional views, I will review evidence suggesting that content-specific information can be flexibly maintained in areas across the cortical hierarchy ranging from early visual cortex to PFC. While the factors that determine exactly where content-specific information is represented are not yet entirely clear, recognizing the importance of task-demands and better understanding the operation of non-spiking neural codes may help to constrain new theories about how memories are maintained at different resolutions, across different timescales, and in the presence of distracting information. PMID:27668990

Methods, systems, and apparatus for storage, transfer and/or control of information via matter wave dynamics

Science.gov (United States)

Vestergaard Hau, Lene (Inventor)

2012-01-01

Methods, systems and apparatus for generating atomic traps, and for storing, controlling and transferring information between first and second spatially separated phase-coherent objects, or using a single phase-coherent object. For plural objects, both phase-coherent objects have a macroscopic occupation of a particular quantum state by identical bosons or identical BCS-paired fermions. The information may be optical information, and the phase-coherent object(s) may be Bose-Einstein condensates, superfluids, or superconductors. The information is stored in the first phase-coherent object at a first storage time and recovered from the second phase-coherent object, or the same first phase-coherent object, at a second revival time. In one example, an integrated silicon wafer-based optical buffer includes an electrolytic atom source to provide the phase-coherent object(s), a nanoscale atomic trap for the phase-coherent object(s), and semiconductor-based optical sources to cool the phase-coherent object(s) and provide coupling fields for storage and transfer of optical information.

Storage Information Management System (SIMS) Spaceflight Hardware Warehousing at Goddard Space Flight Center

Science.gov (United States)

Kubicko, Richard M.; Bingham, Lindy

1995-01-01

Goddard Space Flight Center (GSFC) on site and leased warehouses contain thousands of items of ground support equipment (GSE) and flight hardware including spacecraft, scaffolding, computer racks, stands, holding fixtures, test equipment, spares, etc. The control of these warehouses, and the management, accountability, and control of the items within them, is accomplished by the Logistics Management Division. To facilitate this management and tracking effort, the Logistics and Transportation Management Branch, is developing a system to provide warehouse personnel, property owners, and managers with storage and inventory information. This paper will describe that PC-based system and address how it will improve GSFC warehouse and storage management.

High density data storage principle, technology, and materials

CERN Document Server

Zhu, Daoben

2009-01-01

The explosive increase in information and the miniaturization of electronic devices demand new recording technologies and materials that combine high density, fast response, long retention time and rewriting capability. As predicted, the current silicon-based computer circuits are reaching their physical limits. Further miniaturization of the electronic components and increase in data storage density are vital for the next generation of IT equipment such as ultra high-speed mobile computing, communication devices and sophisticated sensors. This original book presents a comprehensive introduction to the significant research achievements on high-density data storage from the aspects of recording mechanisms, materials and fabrication technologies, which are promising for overcoming the physical limits of current data storage systems. The book serves as an useful guide for the development of optimized materials, technologies and device structures for future information storage, and will lead readers to the fascin...

An emerging network storage management standard: Media error monitoring and reporting information (MEMRI) - to determine optical tape data integrity

Science.gov (United States)

Podio, Fernando; Vollrath, William; Williams, Joel; Kobler, Ben; Crouse, Don

1998-01-01

Sophisticated network storage management applications are rapidly evolving to satisfy a market demand for highly reliable data storage systems with large data storage capacities and performance requirements. To preserve a high degree of data integrity, these applications must rely on intelligent data storage devices that can provide reliable indicators of data degradation. Error correction activity generally occurs within storage devices without notification to the host. Early indicators of degradation and media error monitoring 333 and reporting (MEMR) techniques implemented in data storage devices allow network storage management applications to notify system administrators of these events and to take appropriate corrective actions before catastrophic errors occur. Although MEMR techniques have been implemented in data storage devices for many years, until 1996 no MEMR standards existed. In 1996 the American National Standards Institute (ANSI) approved the only known (world-wide) industry standard specifying MEMR techniques to verify stored data on optical disks. This industry standard was developed under the auspices of the Association for Information and Image Management (AIIM). A recently formed AIIM Optical Tape Subcommittee initiated the development of another data integrity standard specifying a set of media error monitoring tools and media error monitoring information (MEMRI) to verify stored data on optical tape media. This paper discusses the need for intelligent storage devices that can provide data integrity metadata, the content of the existing data integrity standard for optical disks, and the content of the MEMRI standard being developed by the AIIM Optical Tape Subcommittee.

Significantly Elevated Dielectric and Energy Storage Traits in Boron Nitride Filled Polymer Nano-composites with Topological Structure

Science.gov (United States)

Feng, Yefeng; Zhang, Jianxiong; Hu, Jianbing; Li, Shichun; Peng, Cheng

2018-03-01

Interface induced polarization has a prominent influence on dielectric properties of 0-3 type polymer based composites containing Si-based semi-conductors. The disadvantages of composites were higher dielectric loss, lower breakdown strength and energy storage density, although higher permittivity was achieved. In this work, dielectric, conductive, breakdown and energy storage properties of four nano-composites have been researched. Based on the cooperation of fluoropolymer/alpha-SiC layer and fluoropolymer/hexagonal-BN layer, it was confirmed constructing the heterogeneous layer-by-layer composite structure rather than homogeneous mono-layer structure could significantly reduce dielectric loss, promote breakdown strength and increase energy storage density. The former worked for a larger dielectric response and the latter layer acted as a robust barrier of charge carrier transfer. The best nano-composite could possess a permittivity of 43@100 Hz ( 3.3 times of polymer), loss of 0.07@100 Hz ( 37% of polymer), discharged energy density of 2.23 J/cm3@249 kV/cm ( 10 times of polymer) and discharged energy efficiency of 54%@249 kV/cm ( 5 times of polymer). This work might enlighten a facile route to achieve the promising high energy storage composite dielectrics by constructing the layer-by-layer topological structure.

Straight-Line: A nuclear material storage information management system

International Nuclear Information System (INIS)

Nilsen, C.; Mangan, D.

1995-01-01

Sandia National Laboratories is developing Straight-Line -- a pilot system to demonstrate comprehensive monitoring of nuclear material in storage. Straight-Line is an integrated system of sensors providing information that will enhance the safety, security, and international accountability of stored nuclear material. The goals of this effort are to: (1) Provide the right sensor information to the right user immediately. (2) Reduce the expenses, risks, and frequency of human inspection of the material. (3) Provide trustworthy data to international inspectors to minimize their need to make on site inspections. In pursuit of these goals, Straight-Line unites technology from Sandia's Authenticated Item Monitoring System (AIMS) and other programs to communicate the authenticated status of the monitored item back to central magazine receivers. Straight-Line, however, incorporates several important features not found in previous systems: (1) Information Security -- the ability to collect and safely disseminate both classified and unclassified sensor data to users on a need-to-know basis. (2) Integrate into a single system the monitoring needs of safety, security, and international accountability. (3) Incorporate the use of sensors providing analog or digital output. This paper will present the overall architecture and status of the Straight-Line project

Straight-Line: A nuclear material storage information management system

Energy Technology Data Exchange (ETDEWEB)

Nilsen, C.; Mangan, D.

1995-07-01

Sandia National Laboratories is developing Straight-Line -- a pilot system to demonstrate comprehensive monitoring of nuclear material in storage. Straight-Line is an integrated system of sensors providing information that will enhance the safety, security, and international accountability of stored nuclear material. The goals of this effort are to: (1) Provide the right sensor information to the right user immediately. (2) Reduce the expenses, risks, and frequency of human inspection of the material. (3) Provide trustworthy data to international inspectors to minimize their need to make on site inspections. In pursuit of these goals, Straight-Line unites technology from Sandia`s Authenticated Item Monitoring System (AIMS) and other programs to communicate the authenticated status of the monitored item back to central magazine receivers. Straight-Line, however, incorporates several important features not found in previous systems: (1) Information Security -- the ability to collect and safely disseminate both classified and unclassified sensor data to users on a need-to-know basis. (2) Integrate into a single system the monitoring needs of safety, security, and international accountability. (3) Incorporate the use of sensors providing analog or digital output. This paper will present the overall architecture and status of the Straight-Line project.

National Waste Terminal Storage Program information meeting, December 7-8, 1976. [Slides only, no text

Energy Technology Data Exchange (ETDEWEB)

1976-12-06

Volume II of the report comprises copies of the slides from the talks presented at the second session of the National Waste Terminal Storage Program information meeting. This session was devoted to geologic studies. (LK)

Thermal energy storage devices, systems, and thermal energy storage device monitoring methods

Science.gov (United States)

Tugurlan, Maria; Tuffner, Francis K; Chassin, David P.

2016-09-13

Thermal energy storage devices, systems, and thermal energy storage device monitoring methods are described. According to one aspect, a thermal energy storage device includes a reservoir configured to hold a thermal energy storage medium, a temperature control system configured to adjust a temperature of the thermal energy storage medium, and a state observation system configured to provide information regarding an energy state of the thermal energy storage device at a plurality of different moments in time.

National Waste Terminal Storage Program: information management plan. Volume II. Plan description

International Nuclear Information System (INIS)

1977-05-01

A comprehensive information management plan to provide for the systematic processing of large amounts of internally prepared and externally acquired documentation that will accrue to the Office of Waste Isolation (OWI) during the next decade is outlined. The Information Management Plan of the National Waste Terminal Storage (NWTS) Program is based on time proven procedures developed by government and industry for the requirements determination, acquisition, and the administration of documentation. The NWTS Information Management Plan is designed to establish the basis for the planning, development, implemenation, operation and maintenance of the NWTS Information Management System. This plan will help assure that documentation meets required quality standards and that each organization's needs are reflected when soliciting documentation from subcontractors. An example would be the Quality Assurance documentation requirement necessary to comply with eventual NRC licensing regulations. The provisions of the NWTS Information Management Plan will apply to all documentation from OWI contractors, subcontractors, and suppliers, and to OWI organizations for documentation prepared periodically for external dissemination

Technology for national asset storage systems

Science.gov (United States)

Coyne, Robert A.; Hulen, Harry; Watson, Richard

1993-01-01

An industry-led collaborative project, called the National Storage Laboratory, was organized to investigate technology for storage systems that will be the future repositories for our national information assets. Industry participants are IBM Federal Systems Company, Ampex Recording Systems Corporation, General Atomics DISCOS Division, IBM ADSTAR, Maximum Strategy Corporation, Network Systems Corporation, and Zitel Corporation. Industry members of the collaborative project are funding their own participation. Lawrence Livermore National Laboratory through its National Energy Research Supercomputer Center (NERSC) will participate in the project as the operational site and the provider of applications. The expected result is an evaluation of a high performance storage architecture assembled from commercially available hardware and software, with some software enhancements to meet the project's goals. It is anticipated that the integrated testbed system will represent a significant advance in the technology for distributed storage systems capable of handling gigabyte class files at gigabit-per-second data rates. The National Storage Laboratory was officially launched on 27 May 1992.

Straight-Line -- A nuclear material storage information management system

International Nuclear Information System (INIS)

Nilsen, C.; Mangan, D.

1995-01-01

Sandia National Laboratories is developing Straight-Line -- a pilot system to demonstrate comprehensive monitoring of nuclear material in storage. Straight-Line is an integrated system of sensors providing information that will enhance the safety, security, and international accountability of stored nuclear material. The goals of this effort are to (1) Provide the right sensor information to the right user in a timely manner. (2) Reduce the expenses, risks, and frequency of human inspection of the material. (3) Provide trustworthy data to international inspectors to minimize their need to make on site inspections. In pursuit of these goals, Straight-Line unites technology from Sandia's Authenticated Item Monitoring System (AIMS) and other programs to communicate the authenticated status of the monitored item back to central magazine receivers. Straight-Line, however, incorporates several important features not found in previous systems: (1) Information Security -- the ability to collect and safely disseminate both classified and unclassified sensor data to users on a need-to-know basis. (2) Integrate into a single system the monitoring needs of safety, security, and international accountability. (3) Incorporate the use of sensors providing analog or digital output. This paper will present the overall architecture and status of the Straight-Line project

Straight-Line -- A nuclear material storage information management system

Energy Technology Data Exchange (ETDEWEB)

Nilsen, C. [Sandia National Labs., Livermore, CA (United States); Mangan, D. [Sandia National Labs., Albuquerque, NM (United States)

1995-12-31

Sandia National Laboratories is developing Straight-Line -- a pilot system to demonstrate comprehensive monitoring of nuclear material in storage. Straight-Line is an integrated system of sensors providing information that will enhance the safety, security, and international accountability of stored nuclear material. The goals of this effort are to (1) Provide the right sensor information to the right user in a timely manner. (2) Reduce the expenses, risks, and frequency of human inspection of the material. (3) Provide trustworthy data to international inspectors to minimize their need to make on site inspections. In pursuit of these goals, Straight-Line unites technology from Sandia`s Authenticated Item Monitoring System (AIMS) and other programs to communicate the authenticated status of the monitored item back to central magazine receivers. Straight-Line, however, incorporates several important features not found in previous systems: (1) Information Security -- the ability to collect and safely disseminate both classified and unclassified sensor data to users on a need-to-know basis. (2) Integrate into a single system the monitoring needs of safety, security, and international accountability. (3) Incorporate the use of sensors providing analog or digital output. This paper will present the overall architecture and status of the Straight-Line project.

Use of information-retrieval languages in automated retrieval of experimental data from long-term storage

Science.gov (United States)

Khovanskiy, Y. D.; Kremneva, N. I.

1975-01-01

Problems and methods are discussed of automating information retrieval operations in a data bank used for long term storage and retrieval of data from scientific experiments. Existing information retrieval languages are analyzed along with those being developed. The results of studies discussing the application of the descriptive 'Kristall' language used in the 'ASIOR' automated information retrieval system are presented. The development and use of a specialized language of the classification-descriptive type, using universal decimal classification indices as the main descriptors, is described.

Information storage and retrieval system at Westinghouse Hanford Company Hanford Engineering Development Laboratory (HEDL)

International Nuclear Information System (INIS)

Theo, M.G.

1977-01-01

The information storage and retrieval system developed at Westinghouse--Hanford is described. It will be able to store over two million documents on line. The system uses an interactive minicomputer to search for keyworded documents. Documents of interest can be displayed on CRTs or printed on microfilm reader--printers. 31 figures

[Microbiological Aspects of Radioactive Waste Storage].

Science.gov (United States)

Safonov, A V; Gorbunova, O A; German, K E; Zakharova, E V; Tregubova, V E; Ershov, B G; Nazina, T N

2015-01-01

The article gives information about the microorganisms inhabiting in surface storages of solid radioactive waste and deep disposal sites of liquid radioactive waste. It was shown that intensification of microbial processes can lead to significant changes in the chemical composition and physical state of the radioactive waste. It was concluded that the biogeochemical processes can have both a positive effect on the safety of radioactive waste storages (immobilization of RW macrocomponents, a decreased migration ability of radionuclides) and a negative one (biogenic gas production in subterranean formations and destruction of cement matrix).

Side-chain liquid crystalline polyesters for optical information storage

DEFF Research Database (Denmark)

Ramanujam, P.S.; Holme, Christian; Hvilsted, Søren

1996-01-01

and holographic storage in one particular polyester are described in detail and polarized Fourier transform infrared spectroscopic data complementing the optical data are presented. Optical and atomic force microscope investigations point to a laser-induced aggregation as responsible for permanent optical storage.......Azobenzene side-chain liquid crystalline polyester structures suitable for permanent optical storage are described. The synthesis and characterization of the polyesters together with differential scanning calorimetry and X-ray investigations are discussed. Optical anisotropic investigations...

Mussel-inspired Fluoro-Polydopamine Functionalization of Titanium Dioxide Nanowires for Polymer Nanocomposites with Significantly Enhanced Energy Storage Capability

Science.gov (United States)

Wang, Guanyao; Huang, Xingyi; Jiang, Pingkai

2017-01-01

High-dielectric-constant polymer nanocomposites are demonstrated to show great promise as energy storage materials. However, the large electrical mismatch and incompatibility between nanofillers and polymer matrix usually give rise to significantly reduced breakdown strength and weak energy storage capability. Therefore, rational selection and elaborate functionalization of nanofillers to optimize the performance of polymer nanocomposites are vital. Herein, inspired by adhesive proteins in mussels, a facile modification by fluoro-polydopamine is employed to reinforce the compatibility of TiO2 nanowires in the fluoropolymer matrix. The loading of 2.5 vol % f-DOPA@TiO2 NWs leads to an ultrahigh discharged energy density of 11.48 J cm−3 at 530 MV m−1, more than three times of commercial biaxial-oriented polypropylene (BOPP, 3.56 J cm−3 at 600 MV m−1). A gratifying high energy density of 9.12 J cm−3 has also been obtained with nanofiller loading as high as 15 vol % at 360 MV m−1, which is nearly double to that of pure P(VDF-HFP) (4.76 J cm−3 at 360 MV m−1). This splendid energy storage capability seems to rival or exceed most of previously reported nano-TiO2 based nanocomposites. The methods presented here provide deep insights into the design of polymer nanocomposites for energy storage applications. PMID:28225047

Mussel-inspired Fluoro-Polydopamine Functionalization of Titanium Dioxide Nanowires for Polymer Nanocomposites with Significantly Enhanced Energy Storage Capability

Science.gov (United States)

Wang, Guanyao; Huang, Xingyi; Jiang, Pingkai

2017-02-01

High-dielectric-constant polymer nanocomposites are demonstrated to show great promise as energy storage materials. However, the large electrical mismatch and incompatibility between nanofillers and polymer matrix usually give rise to significantly reduced breakdown strength and weak energy storage capability. Therefore, rational selection and elaborate functionalization of nanofillers to optimize the performance of polymer nanocomposites are vital. Herein, inspired by adhesive proteins in mussels, a facile modification by fluoro-polydopamine is employed to reinforce the compatibility of TiO2 nanowires in the fluoropolymer matrix. The loading of 2.5 vol % f-DOPA@TiO2 NWs leads to an ultrahigh discharged energy density of 11.48 J cm-3 at 530 MV m-1, more than three times of commercial biaxial-oriented polypropylene (BOPP, 3.56 J cm-3 at 600 MV m-1). A gratifying high energy density of 9.12 J cm-3 has also been obtained with nanofiller loading as high as 15 vol % at 360 MV m-1, which is nearly double to that of pure P(VDF-HFP) (4.76 J cm-3 at 360 MV m-1). This splendid energy storage capability seems to rival or exceed most of previously reported nano-TiO2 based nanocomposites. The methods presented here provide deep insights into the design of polymer nanocomposites for energy storage applications.

Costing of spent nuclear fuel storage

International Nuclear Information System (INIS)

2009-01-01

This report deals with economic analysis and cost estimation, based on exploration of relevant issues, including a survey of analytical tools for assessment and updated information on the market and financial issues associated with spent fuel storage. The development of new storage technologies and changes in some of the circumstances affecting the costs of spent fuel storage are also incorporated. This report aims to provide comprehensive information on spent fuel storage costs to engineers and nuclear professionals as well as other stakeholders in the nuclear industry. This report is meant to provide informative guidance on economic aspects involved in selecting a spent fuel storage system, including basic methods of analysis and cost data for project evaluation and comparison of storage options, together with financial and business aspects associated with spent fuel storage. After the review of technical options for spent fuel storage in Section 2, cost categories and components involved in the lifecycle of a storage facility are identified in Section 3 and factors affecting costs of spent fuel storage are then reviewed in the Section 4. Methods for cost estimation and analysis are introduced in Section 5, and other financial and business aspects associated with spent fuel storage are discussed in Section 6.

ERDA's Chemical Energy Storage Program

Science.gov (United States)

Swisher, J. H.; Kelley, J. H.

1977-01-01

The Chemical Energy Storage Program is described with emphasis on hydrogen storage. Storage techniques considered include pressurized hydrogen gas storage, cryogenic liquid hydrogen storage, storage in hydride compounds, and aromatic-alicyclic hydrogen storage. Some uses of energy storage are suggested. Information on hydrogen production and hydrogen use is also presented. Applications of hydrogen energy systems include storage of hydrogen for utilities load leveling, industrial marketing of hydrogen both as a chemical and as a fuel, natural gas supplementation, vehicular applications, and direct substitution for natural gas.

Intelligent Management System of Power Network Information Collection Under Big Data Storage

Directory of Open Access Journals (Sweden)

Qin Yingying

2017-01-01

Full Text Available With the development of economy and society, big data storage in enterprise management has become a problem that can’t be ignored. How to manage and optimize the allocation of tasks better is an important factor in the sustainable development of an enterprise. Now the enterprise information intelligent management has become a hot spot of management mode and concept in the information age. It presents information to the business managers in a more efficient, lower cost, and global form. The system uses the SG-UAP development tools, which is based on Eclipse development environment, and suits for Windows operating system, with Oracle as database development platform, Tomcat network information service for application server. The system uses SOA service-oriented architecture, provides RESTful style service, and HTTP(S as the communication protocol, and JSON as the data format. The system is divided into two parts, the front-end and the backs-end, achieved functions like user login, registration, password retrieving, enterprise internal personnel information management and internal data display and other functions.

VALORA: data base system for storage significant information used in the behavior modelling in the biosphere

International Nuclear Information System (INIS)

Valdes R, M.; Aguero P, A.; Perez S, D.; Cancio P, D.

2006-01-01

The nuclear and radioactive facilities can emit to the environment effluents that contain radionuclides, which are dispersed and/or its accumulate in the atmosphere, the terrestrial surface and the surface waters. As part of the evaluations of radiological impact, it requires to be carried out qualitative and quantitative analysis. In many of the cases it doesn't have the real values of the parameters that are used in the modelling, neither it is possible to carry out their measure, for that to be able to carry out the evaluation it needs to be carried out an extensive search of that published in the literature about the possible values of each parameter, under similar conditions to the object of study, this work can be extensive. In this work the characteristics of the VALORA Database System developed with the purpose of organizing and to automate significant information that it appears in different sources (scientific or technique literature) of the parameters that are used in the modelling of the behavior of the pollutants in the environment and the values assigned to these parameters that are used in the evaluation of the radiological impact potential is described; VALORA allows the consultation and selection of the characteristic parametric data of different situations and processes that are required by the calculation pattern implemented. The software VALORA it is a component of a group of tools computer that have as objective to help to the resolution of dispersion models and transfer of pollutants. (Author)

Information report on nuclear safety and radiation protection of the Manche storage Centre - 2012

International Nuclear Information System (INIS)

2013-06-01

After a presentation of the Manche Storage Centre (CSM), the first French centre of surface storage of weakly and moderately radioactive wastes, of its history, its buildings and activities, of the multi-layer cover, of the water management system (installation, controls, sampling), this report describes the measures related to nuclear safety (principles and objectives, prevention measures, technical measures, regulatory plan of control of the Centre and of its environment, control of releases from storage installations, quality organisation, archiving system). It describes measures related to radiation protection: principles, staff dosimetry, and personnel safety. The next part presents the nuclear event scale (INES) and indicates that no incident occurred. The effluents and releases from the Centre are then addressed: origin, locations and results of radiological controls of rainfalls, of risky effluents, of underground waters, of rivers, impacts of the Centre on its environment (releases in the sea, in rivers). The management of conventional and nuclear wastes produced by the Centre is reviewed as well as the actions related to information and transparency. Recommendations of the CHSCT are reported

A national look at carbon capture and storage-National carbon sequestration database and geographical information system (NatCarb)

Science.gov (United States)

Carr, T.R.; Iqbal, A.; Callaghan, N.; ,; Look, K.; Saving, S.; Nelson, K.

2009-01-01

The US Department of Energy's Regional Carbon Sequestration Partnerships (RCSPs) are responsible for generating geospatial data for the maps displayed in the Carbon Sequestration Atlas of the United States and Canada. Key geospatial data (carbon sources, potential storage sites, transportation, land use, etc.) are required for the Atlas, and for efficient implementation of carbon sequestration on a national and regional scale. The National Carbon Sequestration Database and Geographical Information System (NatCarb) is a relational database and geographic information system (GIS) that integrates carbon storage data generated and maintained by the RCSPs and various other sources. The purpose of NatCarb is to provide a national view of the carbon capture and storage potential in the U.S. and Canada. The digital spatial database allows users to estimate the amount of CO2 emitted by sources (such as power plants, refineries and other fossil-fuel-consuming industries) in relation to geologic formations that can provide safe, secure storage sites over long periods of time. The NatCarb project is working to provide all stakeholders with improved online tools for the display and analysis of CO2 carbon capture and storage data. NatCarb is organizing and enhancing the critical information about CO2 sources and developing the technology needed to access, query, model, analyze, display, and distribute natural resource data related to carbon management. Data are generated, maintained and enhanced locally at the RCSP level, or at specialized data warehouses, and assembled, accessed, and analyzed in real-time through a single geoportal. NatCarb is a functional demonstration of distributed data-management systems that cross the boundaries between institutions and geographic areas. It forms the first step toward a functioning National Carbon Cyberinfrastructure (NCCI). NatCarb provides access to first-order information to evaluate the costs, economic potential and societal issues of

DOE/EPRI Electricity Storage Handbook in Collaboration with NRECA

Energy Technology Data Exchange (ETDEWEB)

Akhil, Abbas A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Energy Storage Technology and Systems; Huff, Georgianne [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Energy Storage Technology and Systems; Currier, Aileen B. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Energy Storage Technology and Systems; Hernandez, Jacquelynne [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Energy Storage Technology and Systems; Bender, Donald Arthur [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Kaun, Benjamin C. [Electric Power Research Inst. (EPRI), Palo Alto, CA (United States); Rastler, Dan M. [Electric Power Research Inst. (EPRI), Palo Alto, CA (United States); Chen, Stella Bingqing [Electric Power Research Inst. (EPRI), Palo Alto, CA (United States); Cotter, Andrew L. [National Rural Electric Cooperative Association, Arlington, VA (United States); Bradshaw, Dale T. [National Rural Electric Cooperative Association, Arlington, VA (United States); Gauntlett, William D. [AECOM Technical Services, Inc., Albuquerque, NM (United States); Eyer, James [Clean Energy States Alliance, Montpelier, VT (United States); Olinsky-Paul, Todd [Clean Energy States Alliance, Montpelier, VT (United States); Ellison, Michelle [E& I Consulting, Oakland, CA (United States); Schoenung, Susan [Longitude 122 West, Inc., Menlo Park, CA (United States)

2016-09-01

The Electricity Storage Handbook (Handbook) is a how-to guide for utility and rural cooperative engineers, planners, and decision makers to plan and implement energy storage projects. The Handbook also serves as an information resource for investors and venture capitalists, providing the latest developments in technologies and tools to guide their evaluations of energy storage opportunities. It includes a comprehensive database of the cost of current storage systems in a wide variety of electric utility and customer services, along with interconnection schematics. A list of significant past and present energy storage projects is provided for a practical perspective. This Handbook, jointly sponsored by the U.S. Department of Energy and the Electric Power Research Institute in collaboration with the National Rural Electric Cooperative Association, is published in electronic form at www.sandia.gov/ess.

Storage and executive processes in the frontal lobes.

Science.gov (United States)

Smith, E E; Jonides, J

1999-03-12

The human frontal cortex helps mediate working memory, a system that is used for temporary storage and manipulation of information and that is involved in many higher cognitive functions. Working memory includes two components: short-term storage (on the order of seconds) and executive processes that operate on the contents of storage. Recently, these two components have been investigated in functional neuroimaging studies. Studies of storage indicate that different frontal regions are activated for different kinds of information: storage for verbal materials activates Broca's area and left-hemisphere supplementary and premotor areas; storage of spatial information activates the right-hemisphere premotor cortex; and storage of object information activates other areas of the prefrontal cortex. Two of the fundamental executive processes are selective attention and task management. Both processes activate the anterior cingulate and dorsolateral prefrontal cortex.

Canadian experience with wet and dry fuel storage concepts

International Nuclear Information System (INIS)

Mayman, S.A.

1978-07-01

Canada has been storing fuel in water-filled pools for 30 years. There have been no significant problems, but until recently little effort has been invested in quantitative assessment of fuel performance under storage conditions. Work is now in progress to provide such information. Storage pools at nuclear generating stations have operated satisfactorily. The Canadian nuclear industry has nevertheless been studying methods for reducing storage costs and/or increasing reliability. Various concepts, using both water and air cooling, have been suggested. One such concept - the air-cooled concrete canister - is presently under test at the Whiteshell Nuclear Research Establishment. (author)

A GIS-based 3D online information system for underground energy storage in northern Germany

Science.gov (United States)

Nolde, Michael; Malte, Schwanebeck; Ehsan, Biniyaz; Rainer, Duttmann

2015-04-01

We would like to present the concept and current state of development of a GIS-based 3D online information system for underground energy storage. Its aim is to support the local authorities through pre-selection of possible sites for thermal, electrical and substantial underground energy storages. Since the extension of renewable energies has become legal requirement in Germany, the underground storing of superfluously produced green energy (such as during a heavy wind event) in the form of compressed air, gas or heated water has become increasingly important. However, the selection of suitable sites is a complex task. The presented information system uses data of geological features such as rock layers, salt domes and faults enriched with attribute data such as rock porosity and permeability. This information is combined with surface data of the existing energy infrastructure, such as locations of wind and biogas stations, powerline arrangement and cable capacity, and energy distribution stations. Furthermore, legal obligations such as protected areas on the surface and current underground mining permissions are used for the process of pre-selecting sites suitable for energy storage. Not only the current situation but also prospective scenarios, such as expected growth in produced amount of energy are incorporated in the system. While the process of pre-selection itself is completely automated, the user has full control of the weighting of the different factors via the web interface. The system is implemented as an online 3D server GIS environment, so that it can easily be utilized in any web browser. The results are visualized online as interactive 3d graphics. The information system is implemented in the Python programming language in combination with current Web standards, and is build using only free and open source software. It is being developed at Kiel University as part of the ANGUS+ project (lead by Prof. Sebastian Bauer) for the federal state of

DOE/EPRI Electricity Storage Handbook in Collaboration with NRECA.

Energy Technology Data Exchange (ETDEWEB)

Akhil, Abbas Ali [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Huff, Georgianne [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Currier, Aileen B. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Kaun, Benjamin C [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Rastler, Dan M. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Chen, Stella Bingqing [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Cotter, Andrew L. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Bradshaw, Dale T. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Gauntlett, William D. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States)

2015-02-01

The Electricity Storage Handbook (Handbook) is a how - to guide for utility and rural cooperative engineers, planners, and decision makers to plan and implement energy storage projects. The Handbook also serves as an information resource for investors and venture capitalists, providing the latest developments in technologies and tools to guide their evaluation s of energy storage opportunities. It includes a comprehensive database of the cost of current storage systems in a wide variety of electric utility and customer services, along with interconnection schematics. A list of significant past and present energy storage projects is provided for a practical perspective . This Handbook, jointly sponsored by the U.S. Department of Energy and the Electric Power Research Institute in collaboration with the National Rural Electric Cooperative Association, is published in electronic form at www.sandia.gov/ess. This Handbook is best viewed online.

Experience in ultimate storage of radwaste, illustrated by the information on geomechanics gained in the Asse storage facility

International Nuclear Information System (INIS)

Schmidt, M.W.

1981-01-01

Among the numerous variants of storing radioactive waste in the deep geological underground the storage in appropriate mineral salt formations has a couple of particular advantages. In order to effect research- and development works with regard to a safe secular storage of radioactive wastes, the former mineral salt deposit ASSE was assigned to the GSF in the year 1965. At this test plant storage technologies are developed, tested and the operational efficiency of according technical facilities is demonstrated. As a part of these duties several technical and natural scientific fields like nuclear engineering, mining, geomechanics, geochemistry or hydrogeology are worked in interdisciplinarily. Departing from the existing mine building of the shaft ASSE storage bunkers for low- and intermediate-level radioactive wastes (LAW/MAW) are presented. Accompanying geotechnical investigations are explained. An outlook alludes to an eventually possible development potential of the storage bunker arrangement from the geomechanic view. (orig./HP) [de

A Survey on Data Storage and Information Discovery in the WSANs-Based Edge Computing Systems.

Science.gov (United States)

Ma, Xingpo; Liang, Junbin; Liu, Renping; Ni, Wei; Li, Yin; Li, Ran; Ma, Wenpeng; Qi, Chuanda

2018-02-10

In the post-Cloud era, the proliferation of Internet of Things (IoT) has pushed the horizon of Edge computing, which is a new computing paradigm with data are processed at the edge of the network. As the important systems of Edge computing, wireless sensor and actuator networks (WSANs) play an important role in collecting and processing the sensing data from the surrounding environment as well as taking actions on the events happening in the environment. In WSANs, in-network data storage and information discovery schemes with high energy efficiency, high load balance and low latency are needed because of the limited resources of the sensor nodes and the real-time requirement of some specific applications, such as putting out a big fire in a forest. In this article, the existing schemes of WSANs on data storage and information discovery are surveyed with detailed analysis on their advancements and shortcomings, and possible solutions are proposed on how to achieve high efficiency, good load balance, and perfect real-time performances at the same time, hoping that it can provide a good reference for the future research of the WSANs-based Edge computing systems.

A Survey on Data Storage and Information Discovery in the WSANs-Based Edge Computing Systems

Science.gov (United States)

Liang, Junbin; Liu, Renping; Ni, Wei; Li, Yin; Li, Ran; Ma, Wenpeng; Qi, Chuanda

2018-01-01

In the post-Cloud era, the proliferation of Internet of Things (IoT) has pushed the horizon of Edge computing, which is a new computing paradigm with data processed at the edge of the network. As the important systems of Edge computing, wireless sensor and actuator networks (WSANs) play an important role in collecting and processing the sensing data from the surrounding environment as well as taking actions on the events happening in the environment. In WSANs, in-network data storage and information discovery schemes with high energy efficiency, high load balance and low latency are needed because of the limited resources of the sensor nodes and the real-time requirement of some specific applications, such as putting out a big fire in a forest. In this article, the existing schemes of WSANs on data storage and information discovery are surveyed with detailed analysis on their advancements and shortcomings, and possible solutions are proposed on how to achieve high efficiency, good load balance, and perfect real-time performances at the same time, hoping that it can provide a good reference for the future research of the WSANs-based Edge computing systems. PMID:29439442

A Survey on Data Storage and Information Discovery in the WSANs-Based Edge Computing Systems

Directory of Open Access Journals (Sweden)

Xingpo Ma

2018-02-01

Full Text Available In the post-Cloud era, the proliferation of Internet of Things (IoT has pushed the horizon of Edge computing, which is a new computing paradigm with data processed at the edge of the network. As the important systems of Edge computing, wireless sensor and actuator networks (WSANs play an important role in collecting and processing the sensing data from the surrounding environment as well as taking actions on the events happening in the environment. In WSANs, in-network data storage and information discovery schemes with high energy efficiency, high load balance and low latency are needed because of the limited resources of the sensor nodes and the real-time requirement of some specific applications, such as putting out a big fire in a forest. In this article, the existing schemes of WSANs on data storage and information discovery are surveyed with detailed analysis on their advancements and shortcomings, and possible solutions are proposed on how to achieve high efficiency, good load balance, and perfect real-time performances at the same time, hoping that it can provide a good reference for the future research of the WSANs-based Edge computing systems.

Experimental evidence concerning the significant information depth of electron backscatter diffraction (EBSD)

Energy Technology Data Exchange (ETDEWEB)

Wisniewski, Wolfgang, E-mail: wolfgang.w@uni-jena.de [Otto-Schott-Institut, Jena University, Fraunhoferstr. 6, 07743 Jena (Germany); Saager, Stefan [Fraunhofer Institute for Organic Electronics, Electron Beam and Plasma Technology FEP, Winterbergstraße 28, 01277 Dresden (Germany); Böbenroth, Andrea [Fraunhofer Institute for the Microstructure of Materials and Systems IMWS, Walter-Huelse-Straße 1, 06120 Halle (Saale) (Germany); Rüssel, Christian [Otto-Schott-Institut, Jena University, Fraunhoferstr. 6, 07743 Jena (Germany)

2017-02-15

Experiments concerning the information depth of electron backscatter diffraction (EBSD) are performed on samples featuring an amorphous wedge on a crystalline substrate and a crystalline wedge on an amorphous substrate. The effects of the acceleration voltage and exemplary software settings on the ability to measure through an amorphous layer are presented. Changes in the EBSD-signal could be detected through a ≈142 nm thick layer of amorphous Si while orientation measurements could be performed through a ≈116 nm thick layer when using a voltage of 30 kV. The complexity of the information depth significant to a given EBSD-pattern and the multiple parameters influencing it are discussed. It is suggested that a “core information depth” is significant to high quality patterns while a larger “maximum information depth” becomes relevant when the pattern quality decreases or the sample is inhomogeneous within the information volume, i.e. in the form of partially crystalline materials or crystal layers in the nm scale. - Highlights: • Experimental evidence of the significant information depth of EBSD is presented. • Effects of the voltage and exemplary software settings are discussed. • Dependence of the significant information depth on the pattern quality is proposed. • The information depth may reach up to 142 nm in Si when using a voltage of 30 kV. • The information depth depends on the available technology.

Guidebook on spent fuel storage

International Nuclear Information System (INIS)

1984-01-01

The Guidebook summarizes the experience and information in various areas related to spent fuel storage: technological aspects, the transport of spent fuel, economical, regulatory and institutional aspects, international safeguards, evaluation criteria for the selection of a specific spent fuel storage concept, international cooperation on spent fuel storage. The last part of the Guidebook presents specific problems on the spent fuel storage in the United Kingdom, Sweden, USSR, USA, Federal Republic of Germany and Switzerland

Awareness of the need for safe storage of Methadone at home is not improved by the use of protocols on recording information giving

Directory of Open Access Journals (Sweden)

Crome Ilana B

2008-04-01

Full Text Available Abstract Background Methadone is a synthetic, narcotic analgesic used in the treatment of drug misuse. Tragedies involving children being poisoned by the accidental ingestion of methadone are no longer a rare occurrence. Following an audit of the effectiveness of the provision and recall of information to patients attending an NHS Methadone Clinic a protocol was introduced to ensure that staff documented the provision of such information and patients gave a written confirmation that they had received the information. Methods The study was undertaken in the setting of an NHS methadone clinic with the aim of re- auditing the storage of methadone at home following the introduction of the new protocols. 174 patients completed an anonymous questionnaire regarding where they store methadone at home and whether they recall being given advice about safe storage. Community pharmacists were contacted by telephone to assess the level of advice given to methadone patients regarding safety. Results Only 49 (28.2% patients recalled being given advice about safe storage, 24 (13.8% recalled that information was provided by clinic staff. 170 (97.7% patients regard methadone as being dangerous. (28.2%. Methadone is most commonly stored in a cupboard (37.9%. All methadone is dispensed in a bottle with a child resistant cap on it. All patients reported they stored their methadone in the original bottle provided by the pharmacist. Conclusion Recall of information on safety issues is very poor. Provision of written as well as verbal information is needed. The use of printed safety information cards which patients can take away for future reference may be of use. It is the responsibility of health professionals to ensure they provide information and advice to methadone users on the safe storage of their methadone at home.

Systematic assessment of wellbore integrity for geologic carbon storage projects using regulatory and industry information

Energy Technology Data Exchange (ETDEWEB)

Moody, Mark [Battelle Memorial Institute, Columbus, OH (United States); Sminchak, J.R. [Battelle Memorial Institute, Columbus, OH (United States)

2015-11-01

Under this three year project, the condition of legacy oil and gas wells in the Midwest United States was evaluated through analysis of well records, well plugging information, CBL evaluation, sustained casing pressure (SCP) field testing, and analysis of hypothetical CO₂ test areas to provide a realistic description of wellbore integrity factors. The research included a state-wide review of oil and gas well records for Ohio and Michigan, along with more detailed testing of wells in Ohio. Results concluded that oil and gas wells are clustered along fields in areas. Well records vary in quality, and there may be wells that have not been identified in records, but there are options for surveying unknown wells. Many of the deep saline formations being considered for CO₂ storage have few wells that penetrate the storage zone or confining layers. Research suggests that a variety of well construction and plugging approaches have been used over time in the region. The project concluded that wellbore integrity is an important issue for CO₂ storage applications in the Midwest United States. Realistic CO₂ storage projects may cover an area in the subsurface with several hundred legacy oil and gas wells. However, closer inspection may often establish that most of the wells do not penetrate the confining layers or storage zone. Therefore, addressing well integrity may be manageable. Field monitoring of SCP also indicated that tested wells provided zonal isolation of the reservoirs they were designed to isolate. Most of these wells appeared to exhibit gas pressure originating from intermediate zones. Based on these results, more flexibility in terms of cementing wells to surface, allowing well testing, and monitoring wells may aid operators in completing CO₂ storage project. Several useful products were developed under this project for examining wellbore integrity for CO₂ storage applications including, a

Finding of no significant impact: Interim storage of enriched uranium above the maximum historical level at the Y-12 Plant Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1995-01-01

The US Department of Energy (DOE) has prepared an Environmental Assessment (EA) for the Proposed Interim Storage of Enriched Uranium Above the Maximum Historical Storage Level at the Y-12 Plant, Oak Ridge, Tennessee (DOE/EA-0929, September, 1994). The EA evaluates the environmental effects of transportation, prestorage processing, and interim storage of bounding quantities of enriched uranium at the Y-12 Plant over a ten-year period. The State of Tennessee and the public participated in public meetings and workshops which were held after a predecisional draft EA was released in February 1994, and after the revised pre-approval EA was issued in September 1994. Comments provided by the State and public have been carefully considered by the Department. As a result of this public process, the Department has determined that the Y-12 Plant-would store no more than 500 metric tons of highly enriched uranium (HEU) and no more than 6 metric tons of low enriched uranium (LEU). The bounding storage quantities analyzed in the pre-approval EA are 500 metric tons of HEU and 7,105.9 metric tons of LEU. Based on-the analyses in the EA, as revised by the attachment to the Finding of No Significant Impact (FONSI), DOE has determined that interim storage of 500 metric tons of HEU and 6 metric tons of LEU at the Y-12 Plant does not constitute a major Federal action significantly affecting the quality of the human environment, within the meaning of the National Environmental Policy Act (NEPA) of 1969. Therefore, an Environmental Impact Statement (EIS) is not required and the Department is issuing this FONSI

PUREX Storage Tunnels dangerous waste permit application

International Nuclear Information System (INIS)

1991-12-01

The PUREX Storage Tunnels are a mixed waste storage unit consisting of two underground railroad tunnels: Tunnel Number 1 designated 218-E-14 and Tunnel Number 2 designated 218-E-15. The two tunnels are connected by rail to the PUREX Plant and combine to provide storage space for 48 railroad cars (railcars). The PUREX Storage Tunnels provide a long-term storage location for equipment removed from the PUREX Plant. Transfers into the PUREX Storage Tunnels are made on an as-needed basis. Radioactively contaminated equipment is loaded on railcars and remotely transferred by rail into the PUREX Storage Tunnels. Railcars act as both a transport means and a storage platform for equipment placed into the tunnels. This report consists of part A and part B. Part A reports on amounts and locations of the mixed water. Part B permit application consists of the following: Facility Description and General Provisions; Waste Characteristics; Process Information; Groundwater Monitoring; Procedures to Prevent Hazards; Contingency Plan; Personnel Training; Exposure Information Report

An innovative, multidisciplinary educational program in interactive information storage and retrieval. Presentation visuals. M.S. Thesis Final Report, 1 Jul. 1985 - 31 Dec. 1987

Science.gov (United States)

Dominick, Wayne D. (Editor); Gallagher, Mary C.

1985-01-01

This Working Paper Series entry represents a collection of presentation visuals associated with the companion report entitled An Innovative, Multidisciplinary Educational Program in Interactive Information Storage and Retrieval, USL/DBMS NASA/RECON Working Paper Series report number DBMS.NASA/RECON-12. The project objectives are to develop a set of transportable, hands-on, data base management courses for science and engineering students to facilitate their utilization of information storage and retrieval programs.

Privacy-Preserving Outsourced Auditing Scheme for Dynamic Data Storage in Cloud

OpenAIRE

Tu, Tengfei; Rao, Lu; Zhang, Hua; Wen, Qiaoyan; Xiao, Jia

2017-01-01

As information technology develops, cloud storage has been widely accepted for keeping volumes of data. Remote data auditing scheme enables cloud user to confirm the integrity of her outsourced file via the auditing against cloud storage, without downloading the file from cloud. In view of the significant computational cost caused by the auditing process, outsourced auditing model is proposed to make user outsource the heavy auditing task to third party auditor (TPA). Although the first outso...

β-Adrenergic Control of Hippocampal Function: Subserving the Choreography of Synaptic Information Storage and Memory

Science.gov (United States)

Hagena, Hardy; Hansen, Niels; Manahan-Vaughan, Denise

2016-01-01

Noradrenaline (NA) is a key neuromodulator for the regulation of behavioral state and cognition. It supports learning by increasing arousal and vigilance, whereby new experiences are “earmarked” for encoding. Within the hippocampus, experience-dependent information storage occurs by means of synaptic plasticity. Furthermore, novel spatial, contextual, or associative learning drives changes in synaptic strength, reflected by the strengthening of long-term potentiation (LTP) or long-term depression (LTD). NA acting on β-adrenergic receptors (β-AR) is a key determinant as to whether new experiences result in persistent hippocampal synaptic plasticity. This can even dictate the direction of change of synaptic strength. The different hippocampal subfields play different roles in encoding components of a spatial representation through LTP and LTD. Strikingly, the sensitivity of synaptic plasticity in these subfields to β-adrenergic control is very distinct (dentate gyrus > CA3 > CA1). Moreover, NA released from the locus coeruleus that acts on β-AR leads to hippocampal LTD and an enhancement of LTD-related memory processing. We propose that NA acting on hippocampal β-AR, that is graded according to the novelty or saliency of the experience, determines the content and persistency of synaptic information storage in the hippocampal subfields and therefore of spatial memories. PMID:26804338

UFD Storage and Transportation - Transportation Working Group Report

International Nuclear Information System (INIS)

Maheras, Steven J.; Ross, Steven B.

2011-01-01

The Used Fuel Disposition (UFD) Transportation Task commenced in October 2010. As its first task, Pacific Northwest National Laboratory (PNNL) compiled a list of structures, systems, and components (SSCs) of transportation systems and their possible degradation mechanisms during extended storage. The list of SSCs and the associated degradation mechanisms (known as features, events, and processes (FEPs)) were based on the list of used nuclear fuel (UNF) storage system SSCs and degradation mechanisms developed by the UFD Storage Task (Hanson et al. 2011). Other sources of information surveyed to develop the list of SSCs and their degradation mechanisms included references such as Evaluation of the Technical Basis for Extended Dry Storage and Transportation of Used Nuclear Fuel (NWTRB 2010), Transportation, Aging and Disposal Canister System Performance Specification, Revision 1 (OCRWM 2008), Data Needs for Long-Term Storage of LWR Fuel (EPRI 1998), Technical Bases for Extended Dry Storage of Spent Nuclear Fuel (EPRI 2002), Used Fuel and High-Level Radioactive Waste Extended Storage Collaboration Program (EPRI 2010a), Industry Spent Fuel Storage Handbook (EPRI 2010b), and Transportation of Commercial Spent Nuclear Fuel, Issues Resolution (EPRI 2010c). SSCs include items such as the fuel, cladding, fuel baskets, neutron poisons, metal canisters, etc. Potential degradation mechanisms (FEPs) included mechanical, thermal, radiation and chemical stressors, such as fuel fragmentation, embrittlement of cladding by hydrogen, oxidation of cladding, metal fatigue, corrosion, etc. These degradation mechanisms are discussed in Section 2 of this report. The degradation mechanisms have been evaluated to determine if they would be influenced by extended storage or high burnup, the need for additional data, and their importance to transportation. These categories were used to identify the most significant transportation degradation mechanisms. As expected, for the most part, the

Information report on the nuclear safety and radiation protection of the Aube storage Centre - 2012

International Nuclear Information System (INIS)

2013-07-01

This report first present the site of the Aube Storage Centre (CSA), its storage areas, its buildings and equipment, describes the water treatment process, proposes some exploitation data for 2012 (deliveries, storage, compacting), and indicates highlights and works performed in 2012. The next part reviews measures related to nuclear safety: recall of safety principles and objectives, technical arrangements to meet safety objectives, inspections by the ASN, quality audits. The third part reviews measures related to safety and radiation protection: principles for radiation protection, staff dosimetry practices and results, personnel safety, works performed in 2012. The fourth part addresses incidents and accidents (none occurred in 2012) and other minor events classified according to the INES scale. The fifth part addresses the control of the environment and the releases by the centre: measurement locations, measurement results (in the atmosphere, in rivers, in underground waters, radiological control, control of ecosystems, assessment of the radiological impact), physical-chemical control of a local river, actions undertaken for the protection of the environment, highlights for 2012. The next chapter addresses the management of the various wastes produced by the Centre (radioactive wastes, conventional wastes) and the last part reports actions regarding information and transparency. Recommendations of the CHSCT are reported

Mass storage technology in networks

Science.gov (United States)

Ishii, Katsunori; Takeda, Toru; Itao, Kiyoshi; Kaneko, Reizo

1990-08-01

Trends and features of mass storage subsystems in network are surveyed and their key technologies spotlighted. Storage subsystems are becoming increasingly important in new network systems in which communications and data processing are systematically combined. These systems require a new class of high-performance mass-information storage in order to effectively utilize their processing power. The requirements of high transfer rates, high transactional rates and large storage capacities, coupled with high functionality, fault tolerance and flexibility in configuration, are major challenges in storage subsystems. Recent progress in optical disk technology has resulted in improved performance of on-line external memories to optical disk drives, which are competing with mid-range magnetic disks. Optical disks are more effective than magnetic disks in using low-traffic random-access file storing multimedia data that requires large capacity, such as in archive use and in information distribution use by ROM disks. Finally, it demonstrates image coded document file servers for local area network use that employ 130mm rewritable magneto-optical disk subsystems.

Estimating restorable wetland water storage at landscape scales

Science.gov (United States)

Jones, Charles Nathan; Evenson, Grey R.; McLaughlin, Daniel L.; Vanderhoof, Melanie; Lang, Megan W.; McCarty, Greg W.; Golden, Heather E.; Lane, Charles R.; Alexander, Laurie C.

2018-01-01

Globally, hydrologic modifications such as ditching and subsurface drainage have significantly reduced wetland water storage capacity (i.e., volume of surface water a wetland can retain) and consequent wetland functions. While wetland area has been well documented across many landscapes and used to guide restoration efforts, few studies have directly quantified the associated wetland storage capacity. Here, we present a novel raster-based approach to quantify both contemporary and potential (i.e., restorable) storage capacities of individual depressional basins across landscapes. We demonstrate the utility of this method by applying it to the Delmarva Peninsula, a region punctuated by both depressional wetlands and drainage ditches. Across the entire peninsula, we estimated that restoration (i.e., plugging ditches) could increase storage capacity by 80%. Focusing on an individual watershed, we found that over 59% of restorable storage capacity occurs within 20 m of the drainage network, and that 93% occurs within 1 m elevation of the drainage network. Our demonstration highlights widespread ditching in this landscape, spatial patterns of both contemporary and potential storage capacities, and clear opportunities for hydrologic restoration. In Delmarva and more broadly, our novel approach can inform targeted landscape-scale conservation and restoration efforts to optimize hydrologically mediated wetland functions.

Spent fuel storage requirements

International Nuclear Information System (INIS)

Fletcher, J.

1982-06-01

Spent fuel storage requirements, as projected through the year 2000 for U.S. LWRs, were calculated using information supplied by the utilities reflecting plant status as of December 31, 1981. Projections through the year 2000 combined fuel discharge projections of the utilities with the assumed discharges of typical reactors required to meet the nuclear capacity of 165 GWe projected by the Energy Information Administration (EIA) for the year 2000. Three cases were developed and are summarized. A reference case, or maximum at-reactor (AR) capacity case, assumes that all reactor storage pools are increased to their maximum capacities as estimated by the utilities for spent fuel storage utilizing currently licensed technologies. The reference case assumes no transshipments between pools except as currently licensed by the Nuclear Regulatory Commission (NRC). This case identifies an initial requirement for 13 MTU of additional storage in 1984, and a cumulative requirement for 14,490 MTU additional storage in the year 2000. The reference case is bounded by two alternative cases. One, a current capacity case, assumes that only those pool storage capacity increases currently planned by the operating utilities will occur. The second, or maximum capacity with transshipment case, assumes maximum development of pool storage capacity as described above and also assumes no constraints on transshipment of spent fuel among pools of reactors of like type (BWR, PWR) within a given utility. In all cases, a full core discharge capability (full core reserve or FCR) is assumed to be maintained for each reactor, except that only one FCR is maintained when two reactors share a common pool. For the current AR capacity case the indicated storage requirements in the year 2000 are indicated to be 18,190 MTU; for the maximum capacity with transshipment case they are 11,320 MTU

Additional information on monitored retrievable storage

International Nuclear Information System (INIS)

1987-11-01

This report examines various ways in which the transportation and the storage of spent fuel can be managed without an MRS facility and then compares these alternative waste-management systems with a system containing an MRS facility; the comparison is made in terms of system development, operations, cost, risk, and feasibility. It also discusses the costs not quantified in the proposal. It summarizes the views of several US electric utilities and representative groups on both the MRS facility and various at-reactor options that have been proposed for spent-fuel management. 26 refs., 2 figs., 21 tabs

Formation and Maintenance of Robust Long-Term Information Storage in the Presence of Synaptic Turnover.

Directory of Open Access Journals (Sweden)

Michael Fauth

2015-12-01

Full Text Available A long-standing problem is how memories can be stored for very long times despite the volatility of the underlying neural substrate, most notably the high turnover of dendritic spines and synapses. To address this problem, here we are using a generic and simple probabilistic model for the creation and removal of synapses. We show that information can be stored for several months when utilizing the intrinsic dynamics of multi-synapse connections. In such systems, single synapses can still show high turnover, which enables fast learning of new information, but this will not perturb prior stored information (slow forgetting, which is represented by the compound state of the connections. The model matches the time course of recent experimental spine data during learning and memory in mice supporting the assumption of multi-synapse connections as the basis for long-term storage.

AUTOMATIC SUMMARIZATION OF WEB FORUMS AS SOURCES OF PROFESSIONALLY SIGNIFICANT INFORMATION

Directory of Open Access Journals (Sweden)

K. I. Buraya

2016-07-01

Full Text Available Subject of Research.The competitive advantage of a modern specialist is the widest possible coverage of informationsources useful from the point of view of obtaining and acquisition of relevant professionally significant information. Among these sources professional web forums occupy a significant place. The paperconsiders the problem of automaticforum text summarization, i.e. identification ofthose fragments that contain professionally relevant information. Method.The research is based on statistical analysis of texts of forums by means of machine learning. Six web forums were selected for research considering aspects of technologies of various subject domains as their subject-matter. The marking of forums was carried out by an expert way. Using various methods of machine learning the models were designed reflecting functional communication between the estimated characteristics of PSI extraction quality and signs of posts. The cumulative NDCG metrics and its dispersion were used for an assessment of quality of models.Main Results. We have shown that an important role in an assessment of PSI extraction efficiency is played by requestcontext. The contexts of requestshave been selected,characteristic of PSI extraction, reflecting various interpretations of information needs of users, designated by terms relevance and informational content. The scales for their estimates have been designed corresponding to worldwide approaches. We have experimentally confirmed that results of the summarization of forums carried out by experts manually significantly depend on requestcontext. We have shown that in the general assessment of PSI extraction efficiency relevance is rather well described by a linear combination of features, and the informational content assessment already requires their nonlinear combination. At the same time at a relevance assessment the leading role is played by the features connected with keywords, and at an informational content

Performance of high-resolution position-sensitive detectors developed for storage-ring decay experiments

International Nuclear Information System (INIS)

Yamaguchi, T.; Suzaki, F.; Izumikawa, T.; Miyazawa, S.; Morimoto, K.; Suzuki, T.; Tokanai, F.; Furuki, H.; Ichihashi, N.; Ichikawa, C.; Kitagawa, A.; Kuboki, T.; Momota, S.; Nagae, D.; Nagashima, M.; Nakamura, Y.; Nishikiori, R.; Niwa, T.; Ohtsubo, T.; Ozawa, A.

2013-01-01

Highlights: • Position-sensitive detectors were developed for storage-ring decay spectroscopy. • Fiber scintillation and silicon strip detectors were tested with heavy ion beams. • A new fiber scintillation detector showed an excellent position resolution. • Position and energy detection by silicon strip detectors enable full identification. -- Abstract: As next generation spectroscopic tools, heavy-ion cooler storage rings will be a unique application of highly charged RI beam experiments. Decay spectroscopy of highly charged rare isotopes provides us important information relevant to the stellar conditions, such as for the s- and r-process nucleosynthesis. In-ring decay products of highly charged RI will be momentum-analyzed and reach a position-sensitive detector set-up located outside of the storage orbit. To realize such in-ring decay experiments, we have developed and tested two types of high-resolution position-sensitive detectors: silicon strips and scintillating fibers. The beam test experiments resulted in excellent position resolutions for both detectors, which will be available for future storage-ring experiments

The Petascale Data Storage Institute

Energy Technology Data Exchange (ETDEWEB)

Gibson, Garth [Carnegie Mellon Univ., Pittsburgh, PA (United States); Long, Darrell [The Regents of the University of California, Santa Cruz, CA (United States); Honeyman, Peter [Univ. of Michigan, Ann Arbor, MI (United States); Grider, Gary [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Kramer, William [National Energy Research Scientific Computing Center, Berkeley, CA (United States); Shalf, John [National Energy Research Scientific Computing Center, Berkeley, CA (United States); Roth, Philip [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Felix, Evan [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Ward, Lee [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2013-07-01

Petascale computing infrastructures for scientific discovery make petascale demands on information storage capacity, performance, concurrency, reliability, availability, and manageability.The Petascale Data Storage Institute focuses on the data storage problems found in petascale scientific computing environments, with special attention to community issues such as interoperability, community buy-in, and shared tools.The Petascale Data Storage Institute is a collaboration between researchers at Carnegie Mellon University, National Energy Research Scientific Computing Center, Pacific Northwest National Laboratory, Oak Ridge National Laboratory, Sandia National Laboratory, Los Alamos National Laboratory, University of Michigan, and the University of California at Santa Cruz.

Design of the RFID for Storage of Biological Information

Directory of Open Access Journals (Sweden)

Sang-Hee Son

2009-02-01

Full Text Available Recent advances in RFID (radio frequency identification technology promises to create a wireless circuitry capable of interfacing with biological systems for acquisition, identification and processing of biological data based on radio frequency interaction. Thus, the RFID tag can be attached not only to consumer products and form part of the supply chain, but also to animals, plants and in particular human body. This paper describes the strategy for the design of a novel RFID tag, which stores vital biological information such as body temperature and blood pressure and heartbeat in accordance with the EPC global Class-1 standard. Biological data is obtained from a sensor technology that is based on resistance deviation-to-pulse width converter. The integrated chip consists of an analog front end, command interpreter, collision avoidance block, data storage, sensors, and interface circuitry. The system is capable of supporting heartbeats in the range of 40~200 beats per a minute and blood pressure 0~300mmHg. The proposed system employs collision free algorithm that supports access to single tag within a multiple tag environment. The approach facilitates intelligent management of patients in hospitals as part of an integrated healthcare management system.

Stem water storage in five coexisting temperate broad-leaved tree species: significance, temporal dynamics and dependence on tree functional traits.

Science.gov (United States)

Köcher, Paul; Horna, Viviana; Leuschner, Christoph

2013-08-01

The functional role of internal water storage is increasingly well understood in tropical trees and conifers, while temperate broad-leaved trees have only rarely been studied. We examined the magnitude and dynamics of the use of stem water reserves for transpiration in five coexisting temperate broad-leaved trees with largely different morphology and physiology (genera Fagus, Fraxinus, Tilia, Carpinus and Acer). We expected that differences in water storage patterns would mostly reflect species differences in wood anatomy (ring vs. diffuse-porous) and wood density. Sap flux density was recorded synchronously at five positions along the root-to-branch flow path of mature trees (roots, three stem positions and branches) with high temporal resolution (2 min) and related to stem radius changes recorded with electronic point dendrometers. The daily amount of stored stem water withdrawn for transpiration was estimated by comparing the integrated flow at stem base and stem top. The temporal coincidence of flows at different positions and apparent time lags were examined by cross-correlation analysis. Our results confirm that internal water stores play an important role in the four diffuse-porous species with estimated 5-12 kg day(-1) being withdrawn on average in 25-28 m tall trees representing 10-22% of daily transpiration; in contrast, only 0.5-2.0 kg day(-1) was withdrawn in ring-porous Fraxinus. Wood density had a large influence on storage; sapwood area (diffuse- vs. ring-porous) may be another influential factor but its effect was not significant. Across the five species, the length of the time lag in flow at stem top and stem base was positively related to the size of stem storage. The stem stores were mostly exhausted when the soil matrix potential dropped below -0.1 MPa and daily mean vapor pressure deficit exceeded 3-5 hPa. We conclude that stem storage is an important factor improving the water balance of diffuse-porous temperate broad-leaved trees in moist

Finding of no significant impact. Consolidation and interim storage of special nuclear material at Rocky Flats Environmental Technology Site

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-06-01

The Department of Energy (DOE) has prepared an environmental assessment (EA), DOE/EA -- 1060, for the consolidation, processing, and interim storage of Category I and II special nuclear material (SNM) in Building 371 at the Rocky Flats Environmental Technology Site (hereinafter referred to as Rocky Flats or Site), Golden, Colorado. The scope of the EA included alternatives for interim storage including the no action alternative, the construction of a new facility for interim storage at Rocky Flats, and shipment to other DOE facilities for interim storage.

Finding of no significant impact. Consolidation and interim storage of special nuclear material at Rocky Flats Environmental Technology Site

International Nuclear Information System (INIS)

1995-06-01

The Department of Energy (DOE) has prepared an environmental assessment (EA), DOE/EA -- 1060, for the consolidation, processing, and interim storage of Category I and II special nuclear material (SNM) in Building 371 at the Rocky Flats Environmental Technology Site (hereinafter referred to as Rocky Flats or Site), Golden, Colorado. The scope of the EA included alternatives for interim storage including the no action alternative, the construction of a new facility for interim storage at Rocky Flats, and shipment to other DOE facilities for interim storage

Significance of grain boundaries and stacking faults on hydrogen storage properties of Mg2Ni intermetallics processed by high-pressure torsion

International Nuclear Information System (INIS)

Hongo, Toshifumi; Edalati, Kaveh; Arita, Makoto; Matsuda, Junko; Akiba, Etsuo; Horita, Zenji

2015-01-01

Mg 2 Ni intermetallics are processed using three different routes to produce three different microstructural features: annealing at high temperature for coarse grain formation, severe plastic deformation through high-pressure torsion (HPT) for nanograin formation, and HPT processing followed by annealing for the introduction of stacking faults. It is found that both grain boundaries and stacking faults are significantly effective to activate the Mg 2 Ni intermetallics for hydrogen storage at 423 K (150 °C). The hydrogenation kinetics is also considerably enhanced by the introduction of large fractions of grain boundaries and stacking faults while the hydrogenation thermodynamics remains unchanged. This study shows that, similar to grain boundaries and cracks, stacking faults can act as quick pathways for the transportation of hydrogen in the hydrogen storage materials

Study of mined storage caverns

International Nuclear Information System (INIS)

1975-06-01

All available information concerning 75 mined storage caverns as well as the investigative techniques utilized to determine the feasibility of a cavern site is presented. Potential new storage caverns may be for products such as high or low vapor pressure petroleum products, other chemical products, aid industrial or nuclear waste

Liquid crystals for holographic optical data storage

DEFF Research Database (Denmark)

Matharu, Avtar; Jeeva, S.; Ramanujam, P.S.

2007-01-01

to the information storage demands of the 21st century is detailed. Holography is a small subset of the much larger field of optical data storage and similarly, the diversity of materials used for optical data storage is enormous. The theory of polarisation holography which produces holograms of constant intensity...

To DNA, all information is equal

DEFF Research Database (Denmark)

Sennels, Lau; Bentin, Thomas

2012-01-01

Information storage capabilities are key in most aspects of society and the requirement for storage space is rapidly expanding. In principle, DNA could be a high-density medium for information storage. Church and coworkers recently demonstrated how binary data can be encoded, stored in, and retri......Information storage capabilities are key in most aspects of society and the requirement for storage space is rapidly expanding. In principle, DNA could be a high-density medium for information storage. Church and coworkers recently demonstrated how binary data can be encoded, stored in...

Troubleshooting vSphere storage

CERN Document Server

Preston, Mike

2013-01-01

This is a step-by-step example-oriented tutorial aimed at showing the reader how to troubleshoot a variety of vSphere storage problems, and providing the reader with solutions that can be completed with minimal effort and time in order to limit damage to work.If you are a vSphere administrator, this is the book for you. This book will provide you with 'need to know' information about the various storage transports that ESXi utilizes, the tools and techniques we can use to identify problems, and the fundamental knowledge and steps to take to troubleshoot storage-related issues. Prior knowledge

Hanford facility dangerous waste permit application, PUREX storage tunnels

International Nuclear Information System (INIS)

Price, S.M.

1997-01-01

The Hanford Facility Dangerous Waste Permit Application is considered to be a single application organized into a General Information Portion (document number DOE/RL-91-28) and a Unit-Specific Portion. The scope of the Unit-Specific Portion is limited to Part B permit application documentation submitted for individual, operating treatment, storage, and/or disposal units, such as the PUREX Storage Tunnels (this document, DOE/RL-90-24). Both the General Information and Unit-Specific portions of the Hanford Facility Dangerous Waste Permit Application address the content of the Part B permit application guidance prepared by the Washington State Department of Ecology (Ecology 1996) and the US Environmental Protection Agency (40 Code of Federal Regulations 270), with additional information needs defined by the Hazardous and Solid Waste Amendments and revisions of Washington Administrative Code 173-303. For ease of reference, the Washington State Department of Ecology alpha-numeric section identifiers from the permit application guidance documentation (Ecology 1996) follow, in brackets, the chapter headings and subheadings. A checklist indicating where information is contained in the PUREX Storage Tunnels permit application documentation, in relation to the Washington State Department of Ecology guidance, is located in the Contents Section. Documentation contained in the General Information Portion is broader in nature and could be used by multiple treatment, storage, and/or disposal units (e.g., the glossary provided in the General Information Portion). Wherever appropriate, the PUREX Storage Tunnels permit application documentation makes cross-reference to the General Information Portion, rather than duplicating text. Information provided in this PUREX Storage Tunnels permit application documentation is current as of April 1997

Energy storage for electrical systems in the USA

Directory of Open Access Journals (Sweden)

Eugene Freeman

2016-10-01

Full Text Available Energy storage is becoming increasingly important as renewable generation sources such as Wind Turbine and Photo Voltaic Solar are added to the mix in electrical power generation and distribution systems. The paper discusses the basic drivers for energy storage and provides brief descriptions of the various energy storage technologies available. The information summarizes current technical tradeoffs with different storage approaches and identifies issues surrounding deployment of large scale energy storage systems.

Grand Challenges facing Storage Systems

CERN Multimedia

CERN. Geneva

2004-01-01

In this talk, we will discuss the future of storage systems. In particular, we will focus on several big challenges which we are facing in storage, such as being able to build, manage and backup really massive storage systems, being able to find information of interest, being able to do long-term archival of data, and so on. We also present ideas and research being done to address these challenges, and provide a perspective on how we expect these challenges to be resolved as we go forward.

Multiobjective Reliable Cloud Storage with Its Particle Swarm Optimization Algorithm

Directory of Open Access Journals (Sweden)

Xiyang Liu

2016-01-01

Full Text Available Information abounds in all fields of the real life, which is often recorded as digital data in computer systems and treated as a kind of increasingly important resource. Its increasing volume growth causes great difficulties in both storage and analysis. The massive data storage in cloud environments has significant impacts on the quality of service (QoS of the systems, which is becoming an increasingly challenging problem. In this paper, we propose a multiobjective optimization model for the reliable data storage in clouds through considering both cost and reliability of the storage service simultaneously. In the proposed model, the total cost is analyzed to be composed of storage space occupation cost, data migration cost, and communication cost. According to the analysis of the storage process, the transmission reliability, equipment stability, and software reliability are taken into account in the storage reliability evaluation. To solve the proposed multiobjective model, a Constrained Multiobjective Particle Swarm Optimization (CMPSO algorithm is designed. At last, experiments are designed to validate the proposed model and its solution PSO algorithm. In the experiments, the proposed model is tested in cooperation with 3 storage strategies. Experimental results show that the proposed model is positive and effective. The experimental results also demonstrate that the proposed model can perform much better in alliance with proper file splitting methods.

Solar applications of thermal energy storage. Final report

Energy Technology Data Exchange (ETDEWEB)

Lee, C.; Taylor, L.; DeVries, J.; Heibein, S.

1979-01-01

A technology assessment is presented on solar energy systems which use thermal energy storage. The study includes characterization of the current state-of-the-art of thermal energy storage, an assessment of the energy storage needs of solar energy systems, and the synthesis of this information into preliminary design criteria which would form the basis for detailed designs of thermal energy storage. (MHR)

Storage of hydrogen in metals

International Nuclear Information System (INIS)

Wiswall, R.

1981-01-01

A review is dedicated to a problem of hydrogen storage as fuel of future, that can be used under various conditions, is easily obtained with the help of other types of energy and can be transformed into them. Data on reversible metal-hydrogen systems, where hydrogen can be obtained by the way of reaction of thermal decomposition are presented. Pressure-temperature-content diagrams, information on concrete Pd-H, TiFe-H, V-N systems are presented and analyzed from the point of view of thermodynamics. A table with thermodynamical characteristics of several hydrides is presented. The majority of known solid hydrides in relation to their use for hydrogen storage are characterized. The review includes information on real or supposed uses in concrete systems: in fuel cells, for levelling of loading of electric plants, in automobile engines, in hydride engines, for heat storage [ru

Manche storage Centre. Information report on nuclear safety and radiation protection 2014. Annual report 2014

International Nuclear Information System (INIS)

2015-06-01

After a presentation of the Manche Storage Centre (CSM), the first French centre of surface storage of weakly and moderately radioactive wastes, of its history, its buildings and activities, of the multi-layer cover, of the water management system (installation, controls, sampling), this report then describes the measures related to nuclear safety (principles and objectives), the management of conventional and nuclear wastes produced by the Centre and its other environmental impacts. The follow up of the installations and of their effluents and releases are then addressed: origin, locations and results of radiological controls of rainfalls, of risky effluents, of underground waters, of rivers, impacts of the Centre on its environment (releases in the sea, in rivers, in sediments). The measures related to radiation protection are described: principles, staff dosimetry, and personnel safety. The next part presents the nuclear event scale (INES) and indicates that no incident occurred in 2014. Finally the actions related to public information and transparency are summarized. Recommendations of the CHSCT are reported at the end

Dual purpose or not? The significant factors

International Nuclear Information System (INIS)

Bak, W.; Roland, V.

1999-01-01

The development of spent fuel storage systems requires consideration of many factors in making design decisions. A significant issue affecting the design is the need to incorporate transportability of the canister or cask system design, which results in major changes to the storage system design. This paper presents a review of the significant factors affecting storage system design to incorporate transportation requirements and looks at the trends in both the United States and Europe where Transnucleaire and its US affiliated companies Transnuclear Inc., Transnuclear West and PacTec are active. A discussion is also presented relative to the pros and cons of whether the spent fuel storage system vendor should anticipate these transportation needs in the design of their systems. (author)

Environmental assessment, finding of no significant impact, and response to comments. Radioactive waste storage

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-04-01

The Department of Energy`s (DOE) Rocky Flats Environmental Technology Site (the Site), formerly known as the Rocky Flats Plant, has generated radioactive, hazardous, and mixed waste (waste with both radioactive and hazardous constituents) since it began operations in 1952. Such wastes were the byproducts of the Site`s original mission to produce nuclear weapons components. Since 1989, when weapons component production ceased, waste has been generated as a result of the Site`s new mission of environmental restoration and deactivation, decontamination and decommissioning (D&D) of buildings. It is anticipated that the existing onsite waste storage capacity, which meets the criteria for low-level waste (LL), low-level mixed waste (LLM), transuranic (TRU) waste, and TRU mixed waste (TRUM) would be completely filled in early 1997. At that time, either waste generating activities must cease, waste must be shipped offsite, or new waste storage capacity must be developed.

Environmental assessment, finding of no significant impact, and response to comments. Radioactive waste storage

International Nuclear Information System (INIS)

1996-04-01

The Department of Energy's (DOE) Rocky Flats Environmental Technology Site (the Site), formerly known as the Rocky Flats Plant, has generated radioactive, hazardous, and mixed waste (waste with both radioactive and hazardous constituents) since it began operations in 1952. Such wastes were the byproducts of the Site's original mission to produce nuclear weapons components. Since 1989, when weapons component production ceased, waste has been generated as a result of the Site's new mission of environmental restoration and deactivation, decontamination and decommissioning (D ampersand D) of buildings. It is anticipated that the existing onsite waste storage capacity, which meets the criteria for low-level waste (LL), low-level mixed waste (LLM), transuranic (TRU) waste, and TRU mixed waste (TRUM) would be completely filled in early 1997. At that time, either waste generating activities must cease, waste must be shipped offsite, or new waste storage capacity must be developed

Spent fuel storage rack

International Nuclear Information System (INIS)

Morikawa, Matsuo; Uchiyama, Yuichi.

1983-01-01

Purpose: To improve the safety and facilitate the design by limiting the relative displacement in a storage rack. Constitution: The outer wall of a storage rack disposed in water within a fuel pool, the pool wall opposing to the storage rack and the structure between the opposing storages racks are made as a space for confining the pool water or a structure formed with a slight gap, for example, a combination of a recessed structure and a protruded structure. In such a constitution, a space for confirming the pool water is established and the pool water thus confined forms a flow resistance when the storage rack vibrates upon earthquakes, serves as a damper and significantly reduces the responsivity. Furthermore, the relative displacement in the storage rack is limited to inhibit excess earthquake forces to exert on setting bolts and rack clamping bolts of the storage rack. (Sekiya, K.)

Wet storage integrity update

International Nuclear Information System (INIS)

Bailey, W.J.; Johnson, A.B. Jr.

1983-09-01

This report includes information from various studies performed under the Wet Storage Task of the Spent Fuel Integrity Project of the Commercial Spent Fuel Management (CSFM) Program at Pacific Northwest Laboratory. An overview of recent developments in the technology of wet storage of spent water reactor fuel is presented. Licensee Event Reports pertaining to spent fuel pools and the associated performance of spent fuel and storage components during wet storage are discussed. The current status of fuel that was examined under the CSFM Program is described. Assessments of the effect of boric acid in spent fuel pool water on the corrosion and stress corrosion cracking of stainless steel and the stress corrosion cracking of stainless steel piping containing stagnant water at spent fuel pools are discussed. A list of pertinent publications is included. 84 references, 21 figures, 11 tables

Status of US storage efforts

International Nuclear Information System (INIS)

Leasburg, R.H.

1984-01-01

Tasks involved in the implementation of the Nuclear Waste Policy Act are discussed. The need for speedy action on applications to deal with spent fuel storage problems is stressed. The problems faced by the Virginia Electric and Power Company, where full core discharge capability at the 1600-megawatt Surry power station is expected to be reached in early 1986, are reviewed. It is pointed out that although the Nuclear Waste Policy Act does not apply in this case, the problems illustrate the situation that may be faced after the Act is implemented. Problems involved in intro-utility transhipments and dry cask storage of spent fuel from Surry, including transportation ordinances at state and local levels and approval for the use of dry casks for storage, are reported. The suggestion that dry casks be used for interim storage and eventual transport to monitored retrievable storage facilities or permanent storage sites is considered. It is pointed out that data from a proposed 3-utility demonstration program of dry cask storage of consolidated fuels and the storage of fuels in air should give information applicable to the timely implementation of the Nuclear Waste Policy Act

USB Storage Device Forensics for Windows 10.

Science.gov (United States)

Arshad, Ayesha; Iqbal, Waseem; Abbas, Haider

2018-05-01

Significantly increased use of USB devices due to their user-friendliness and large storage capacities poses various threats for many users/companies in terms of data theft that becomes easier due to their efficient mobility. Investigations for such data theft activities would require gathering critical digital information capable of recovering digital forensics artifacts like date, time, and device information. This research gathers three sets of registry and logs data: first, before insertion; second, during insertion; and the third, after removal of a USB device. These sets are analyzed to gather evidentiary information from Registry and Windows Event log that helps in tracking a USB device. This research furthers the prior research on earlier versions of Microsoft Windows and compares it with latest Windows 10 system. Comparison of Windows 8 and Windows 10 does not show much difference except for new subkey under USB Key in registry. However, comparison of Windows 7 with latest version indicates significant variances. © 2017 American Academy of Forensic Sciences.

Data storage for managing the health enterprise and achieving business continuity.

Science.gov (United States)

Hinegardner, Sam

2003-01-01

As organizations move away from a silo mentality to a vision of enterprise-level information, more healthcare IT departments are rejecting the idea of information storage as an isolated, system-by-system solution. IT executives want storage solutions that act as a strategic element of an IT infrastructure, centralizing storage management activities to effectively reduce operational overhead and costs. This article focuses on three areas of enterprise storage: tape, disk, and disaster avoidance.

Solar applications analysis for energy storage

Science.gov (United States)

Blanchard, T.

1980-01-01

The role of energy storage as it relates to solar energy systems is considered. Storage technologies to support solar energy applications, the status of storage technologies, requirements and specifications for storage technologies, and the adequacy of the current storage research and development program to meet these requirements are among the factors discussed. Emphasis is placed on identification of where the greatest potential exists for energy storage in support of those solar energy systems which could have a significant impact on the U.S. energy mix.

Dynamics in the microbiology of maize silage during whole-season storage

DEFF Research Database (Denmark)

Storm, Ida Marie Lindhardt Drejer; Kristensen, N.B.; Raun, B.M.L.

2010-01-01

Aims: To monitor seasonal variations in the microbiology of maize silage and to determine whether the risk of fungal spoilage varies during whole-year storage. Methods and Results: A continuous survey of 20 maize silage stacks was conducted over a period from three to 11 months after ensiling...... variations in the microbiology of maize silage over a whole storage season. The risk of fungal spoilage was highest 5-7 months after ensiling and lowest after 11 months. Significance and Impact of the Study: This information is valuable in the assessment of health risks connected with spoiled maize silage...

Factors Influencing the Adoption of Cloud Storage by Information Technology Decision Makers

Science.gov (United States)

Wheelock, Michael D.

2013-01-01

This dissertation uses a survey methodology to determine the factors behind the decision to adopt cloud storage. The dependent variable in the study is the intent to adopt cloud storage. Four independent variables are utilized including need, security, cost-effectiveness and reliability. The survey includes a pilot test, field test and statistical…

The Aube Storage Centre. Information report on nuclear safety and radiation protection for 2014 - Annual report 2014

International Nuclear Information System (INIS)

2014-06-01

After a presentation of the installations of CSA (Aube Storage Centre), its equipment, its exploitation (deliveries, storage, compacting unit, injection unit, storage works), works performed and highlights in 2014, and perspectives of evolution for 2015 and 2016, this report presents the measures regarding nuclear safety: safety principles, technical measures to meet objectives, inspections performed by the Nuclear Safety Authority (ASN), and quality management. The next part presents measures regarding measures for radiation protection and safety: staff dosimetry (measurements results and evolutions), safety exercise. It outlines that no important incident occurred, and described three minor events which have been declared to the ASN. The next part addresses actions related to the control of the environment and of releases: water management, presentation and discussion of the main results of radiological measurements (rainfalls, air, brook waters, sediments, underground waters, radiation at the edge of the centre, ground vegetal, food chain, aquatic ecosystems), physical-chemical control of waters, actions for the protection of the environment. The report then gives an overview of the management of radioactive and conventional wastes produced by the Centre. The last part indicates and comments actions related to transparency and information (they may concern the public, local authorities, institutions, or media): visits, conferences, exhibitions, animations, partnerships, publications

Federal Interim Storage program

International Nuclear Information System (INIS)

Johnson, E.R.; McBride, J.A.

1984-01-01

The DOE has developed a program for providing Federal Interim Storage servies for spent nuclear fuel which complies with the requirements of the Nuclear Waste Policy Act of 1982. Although very little constructive activity in providing storage facilities can be undertaken by DOE until fuel has been certified by NRC as eligible for FIS, DOE planning and background information is such as to provide reasonable assurance that its obligations can be fulfilled when the required certifications have been issued. A fee structure providing fuel recovery of all costs associated with the FIS program, as required by the Act, has been developed. It provides for an equitable distribution of costs among users, based on the quantity of fuel requiring storage

Integral Monitored Retrievable Storage (MRS) Facility conceptual design report

International Nuclear Information System (INIS)

1985-09-01

This document, Volume 6 Book 1, contains information on design studies of a Monitored Retrievable Storage (MRS) facility. Topics include materials handling; processing; support systems; support utilities; spent fuel; high-level waste and alpha-bearing waste storage facilities; and field drywell storage

Spent fuel storage requirements 1993--2040

International Nuclear Information System (INIS)

1994-09-01

Historical inventories of spent fuel are combined with U.S. Department of Energy (DOE) projections of future discharges from commercial nuclear reactors in the United States to provide estimates of spent fuel storage requirements through the year 2040. The needs are estimated for storage capacity beyond that presently available in the reactor storage pools. These estimates incorporate the maximum capacities within current and planned in-pool storage facilities and any planned transshipments of spent fuel to other reactors or facilities. Existing and future dry storage facilities are also discussed. The nuclear utilities provide historical data through December 1992 on the end of reactor life are based on the DOE/Energy Information Administration (EIA) estimates of future nuclear capacity, generation, and spent fuel discharges

Cost Implications of Uncertainty in CO{sub 2} Storage Resource Estimates: A Review

Energy Technology Data Exchange (ETDEWEB)

Anderson, Steven T., E-mail: sanderson@usgs.gov [National Center, U.S. Geological Survey (United States)

2017-04-15

Carbon capture from stationary sources and geologic storage of carbon dioxide (CO{sub 2}) is an important option to include in strategies to mitigate greenhouse gas emissions. However, the potential costs of commercial-scale CO{sub 2} storage are not well constrained, stemming from the inherent uncertainty in storage resource estimates coupled with a lack of detailed estimates of the infrastructure needed to access those resources. Storage resource estimates are highly dependent on storage efficiency values or storage coefficients, which are calculated based on ranges of uncertain geological and physical reservoir parameters. If dynamic factors (such as variability in storage efficiencies, pressure interference, and acceptable injection rates over time), reservoir pressure limitations, boundaries on migration of CO{sub 2}, consideration of closed or semi-closed saline reservoir systems, and other possible constraints on the technically accessible CO{sub 2} storage resource (TASR) are accounted for, it is likely that only a fraction of the TASR could be available without incurring significant additional costs. Although storage resource estimates typically assume that any issues with pressure buildup due to CO{sub 2} injection will be mitigated by reservoir pressure management, estimates of the costs of CO{sub 2} storage generally do not include the costs of active pressure management. Production of saline waters (brines) could be essential to increasing the dynamic storage capacity of most reservoirs, but including the costs of this critical method of reservoir pressure management could increase current estimates of the costs of CO{sub 2} storage by two times, or more. Even without considering the implications for reservoir pressure management, geologic uncertainty can significantly impact CO{sub 2} storage capacities and costs, and contribute to uncertainty in carbon capture and storage (CCS) systems. Given the current state of available information and the

A Comprehensive Review of Thermal Energy Storage

Directory of Open Access Journals (Sweden)

Ioan Sarbu

2018-01-01

Full Text Available Thermal energy storage (TES is a technology that stocks thermal energy by heating or cooling a storage medium so that the stored energy can be used at a later time for heating and cooling applications and power generation. TES systems are used particularly in buildings and in industrial processes. This paper is focused on TES technologies that provide a way of valorizing solar heat and reducing the energy demand of buildings. The principles of several energy storage methods and calculation of storage capacities are described. Sensible heat storage technologies, including water tank, underground, and packed-bed storage methods, are briefly reviewed. Additionally, latent-heat storage systems associated with phase-change materials for use in solar heating/cooling of buildings, solar water heating, heat-pump systems, and concentrating solar power plants as well as thermo-chemical storage are discussed. Finally, cool thermal energy storage is also briefly reviewed and outstanding information on the performance and costs of TES systems are included.

Utilizing cloud storage architecture for long-pulse fusion experiment data storage

Energy Technology Data Exchange (ETDEWEB)

Zhang, Ming; Liu, Qiang [State Key Laboratory of Advanced Electromagnetic Engineering and Technology, Wuhan, Hubei (China); School of Electrical and Electronic Engineering, Huazhong University of Science and Technology, Wuhan, Hubei (China); Zheng, Wei, E-mail: zhenghaku@gmail.com [State Key Laboratory of Advanced Electromagnetic Engineering and Technology, Wuhan, Hubei (China); School of Electrical and Electronic Engineering, Huazhong University of Science and Technology, Wuhan, Hubei (China); Wan, Kuanhong; Hu, Feiran; Yu, Kexun [State Key Laboratory of Advanced Electromagnetic Engineering and Technology, Wuhan, Hubei (China); School of Electrical and Electronic Engineering, Huazhong University of Science and Technology, Wuhan, Hubei (China)

2016-11-15

Scientific data storage plays a significant role in research facility. The explosion of data in recent years was always going to make data access, acquiring and management more difficult especially in fusion research field. For future long-pulse experiment like ITER, the extremely large data will be generated continuously for a long time, putting much pressure on both the write performance and the scalability. And traditional database has some defects such as inconvenience of management, hard to scale architecture. Hence a new data storage system is very essential. J-TEXTDB is a data storage and management system based on an application cluster and a storage cluster. J-TEXTDB is designed for big data storage and access, aiming at improving read–write speed, optimizing data system structure. The application cluster of J-TEXTDB is used to provide data manage functions and handles data read and write operations from the users. The storage cluster is used to provide the storage services. Both clusters are composed with general servers. By simply adding server to the cluster can improve the read–write performance, the storage space and redundancy, making whole data system highly scalable and available. In this paper, we propose a data system architecture and data model to manage data more efficient. Benchmarks of J-TEXTDB performance including read and write operations are given.

Utilizing cloud storage architecture for long-pulse fusion experiment data storage

International Nuclear Information System (INIS)

Zhang, Ming; Liu, Qiang; Zheng, Wei; Wan, Kuanhong; Hu, Feiran; Yu, Kexun

2016-01-01

Scientific data storage plays a significant role in research facility. The explosion of data in recent years was always going to make data access, acquiring and management more difficult especially in fusion research field. For future long-pulse experiment like ITER, the extremely large data will be generated continuously for a long time, putting much pressure on both the write performance and the scalability. And traditional database has some defects such as inconvenience of management, hard to scale architecture. Hence a new data storage system is very essential. J-TEXTDB is a data storage and management system based on an application cluster and a storage cluster. J-TEXTDB is designed for big data storage and access, aiming at improving read–write speed, optimizing data system structure. The application cluster of J-TEXTDB is used to provide data manage functions and handles data read and write operations from the users. The storage cluster is used to provide the storage services. Both clusters are composed with general servers. By simply adding server to the cluster can improve the read–write performance, the storage space and redundancy, making whole data system highly scalable and available. In this paper, we propose a data system architecture and data model to manage data more efficient. Benchmarks of J-TEXTDB performance including read and write operations are given.

Agency practice and future policy in decay storage of radioactive wastes

International Nuclear Information System (INIS)

Mitchell, N.G.

2002-01-01

The Environment Agency issues authorisations under the Radioactive Substances Act 1993 for the accumulation of radioactive waste at non-nuclear sites prior to disposal. Radioactive decay during the accumulation period reduces the radioactive content of waste packages and provides a waste management option that has become known as decay-in-storage or decay storage. The project brief excluded nuclear licensed sites. A database of information in authorisations and application forms has been constructed. This information has been used alongside a literature review, international contacts, input from the Small Users Liaison Group and a dose assessment to look at the practice of decay storage. The basic principles behind decay storage are presented with specific sections on general safety, waste characterisation and segregation, storage containers, waste stores, and waste treatment and conditioning. The regulatory approach in seven other countries is described. The information collected from Agency public registers is summarised with particular attention given to storage periods of greater than 60 days and the corresponding information available from application forms. Operational experiences are presented. IAEA recommendations are compared with current practice based on the conditions found in authorisations, on the information from application forms and details provided by the Small Users Liaison Group

Carbon storage in forests and peatlands of Russia

Science.gov (United States)

V.A. Alexeyev; R.A. Birdsey; [Editors

1998-01-01

Contains information about carbon storage in the vegetation, soils, and peatlands of Russia. Estimates of carbon storage in forests are derived from statistical data from the 1988 national forest inventory of Russia and from other sources. Methods are presented for converting data on timber stock into phytomass of tree stands, and for estimating carbon storage in...

Re-evaluating the relationships among filtering activity, unnecessary storage, and visual working memory capacity.

Science.gov (United States)

Emrich, Stephen M; Busseri, Michael A

2015-09-01

The amount of task-irrelevant information encoded in visual working memory (VWM), referred to as unnecessary storage, has been proposed as a potential mechanism underlying individual differences in VWM capacity. In addition, a number of studies have provided evidence for additional activity that initiates the filtering process originating in the frontal cortex and basal ganglia, and is therefore a crucial step in the link between unnecessary storage and VWM capacity. Here, we re-examine data from two prominent studies that identified unnecessary storage activity as a predictor of VWM capacity by directly testing the implied path model linking filtering-related activity, unnecessary storage, and VWM capacity. Across both studies, we found that unnecessary storage was not a significant predictor of individual differences in VWM capacity once activity associated with filtering was accounted for; instead, activity associated with filtering better explained variation in VWM capacity. These findings suggest that unnecessary storage is not a limiting factor in VWM performance, whereas neural activity associated with filtering may play a more central role in determining VWM performance that goes beyond preventing unnecessary storage.

GRACE-derived terrestrial water storage depletion associated with the 2003 European heat wave

DEFF Research Database (Denmark)

Andersen, Ole Baltazar; Seneviratne, S.I.; Hinderer, J.

2005-01-01

water storage depletion observed from GRACE can be related to the record-breaking heat wave that occurred in central Europe in 2003. We validate the measurements from GRACE using two independent hydrological estimates and direct gravity observations from superconducting gravimeters in Europe. All...... datasets agree well with the GRACE measurements despite the disparity of the employed information; the difference between datasets tends to be within GRACE margin of error. The April-to-August terrestrial water storage depletion is found to be significantly larger in 2003 than in 2002 from both models......The GRACE twin satellites reveal large inter-annual terrestrial water-storage variations between 2002 and 2003 for central Europe. GRACE observes a negative trend in regional water storage from 2002 to 2003 peaking at -7.8 cm in central Europe with an accuracy of 1 cm. The 2003 excess terrestrial...

Biophysical properties and functional significance of stem water storage tissues in Neotropical savanna trees.

Science.gov (United States)

F.G. Scholz; S.J. Bucci; G. Goldstein; F.C. Meinzer; A.C. Franco; F. Miralles-Wilhelm

2007-01-01

Biophysical characteristics of sapwood and outer parenchyma water storage compartments were studied in stems of eight dominant Brazilian Cerrado tree species to assess the impact of differences in tissue capacitance on whole-plant water relations. Both the sapwood and outer parenchyma tissues played an important role in regulation of internal water deficits of Cerrado...

Aube storage center. Information report on nuclear safety and radiation protection 2015

International Nuclear Information System (INIS)

2016-01-01

The National Radioactive Waste Management Agency (Andra), was established by the December 1991 Waste Act as a public body in charge of the long-term management of all radioactive waste, under the supervision of the Ministry of Ecology, Energy, Sustainable Development and the Sea (formerly the Ministry of Industry and the Ministry of Environment), and the Ministry of Research. The Andra operates two storage centers in the Aube region (France): the center for short-lived low- and intermediate-level wastes, and the center for very-low-level radioactive wastes. This document is the 2015 activity report of the center for short-lived low- and intermediate-level wastes. It presents a review of the activities of the center: presentation of the installations, safety and radiation protection, security, events or incidents, environmental monitoring and effluents, wastes management, public information, recommendations of the Health and safety Committee (CHSCT)

Aube storage center. Information report on nuclear safety and radiation protection 2016

International Nuclear Information System (INIS)

2017-01-01

The National Radioactive Waste Management Agency (Andra), was established by the December 1991 Waste Act as a public body in charge of the long-term management of all radioactive waste, under the supervision of the Ministry of Ecology, Energy, Sustainable Development and the Sea (formerly the Ministry of Industry and the Ministry of Environment), and the Ministry of Research. The Andra operates two storage centers in the Aube region (France): the center for short-lived low- and intermediate-level wastes, and the center for very-low-level radioactive wastes. This document is the 2016 activity report of the center for short-lived low- and intermediate-level wastes. It presents a review of the activities of the center: presentation of the installations, safety and radiation protection, security, events or incidents, environmental monitoring and effluents, wastes management, public information, recommendations of the Health and safety Committee (CHSCT)

Methods and apparatus for capture and storage of semantic information with sub-files in a parallel computing system

Science.gov (United States)

Faibish, Sorin; Bent, John M; Tzelnic, Percy; Grider, Gary; Torres, Aaron

2015-02-03

Techniques are provided for storing files in a parallel computing system using sub-files with semantically meaningful boundaries. A method is provided for storing at least one file generated by a distributed application in a parallel computing system. The file comprises one or more of a complete file and a plurality of sub-files. The method comprises the steps of obtaining a user specification of semantic information related to the file; providing the semantic information as a data structure description to a data formatting library write function; and storing the semantic information related to the file with one or more of the sub-files in one or more storage nodes of the parallel computing system. The semantic information provides a description of data in the file. The sub-files can be replicated based on semantically meaningful boundaries.

Survey of wet and dry spent fuel storage

International Nuclear Information System (INIS)

1999-07-01

Spent fuel storage is one of the important stages in the nuclear fuel cycle and stands among the most vital challenges for countries operating nuclear power plants. Continuous attention is being given by the IAEA to the collection, analysis and exchange of information on spent fuel management. Its role in this area is to provide a forum for exchanging information and for coordinating and encouraging closer co-operation among Member States. Spent fuel management is recognized as a high priority IAEA activity. In 1997, the annual spent fuel arising from all types of power reactors worldwide amounted to about 10,500 tonnes heavy metal (t HM). The total amount of spent fuel accumulated worldwide at the end of 1997 was about 200,000 t HM of which about 130,000 t HM of spent fuel is presently being stored in at-reactor (AR) or away-from-reactor (AFR) storage facilities awaiting either reprocessing or final disposal and 70,000 t HM has been reprocessed. Projections indicate that the cumulative amount generated by 2010 may surpass 340,000 t HM and by the year 2015 395,000 t HM. Part of the spent fuel will be reprocessed and some countries took the option to dispose their spent fuel in a repository. Most countries with nuclear programmes are using the deferral of a decision approach, a 'wait and see' strategy with interim storage, which provides the ability to monitor the storage continuously and to retrieve the spent fuel later for either direct disposal or reprocessing. Some countries use different approaches for different types of fuel. Today the worldwide reprocessing capacity is only a fraction of the total spent fuel arising and since no final repository has yet been constructed, there will be an increasing demand for interim storage. The present survey contains information on the basic storage technologies and facility types, experience with wet and dry storage of spent fuel and international experience in spent fuel transport. The main aim is to provide spent fuel

Using Geographic Information Systems to Determine Site Suitability for a Low-Level Radioactive Waste Storage Facility.

Science.gov (United States)

Wilson, Charles A; Matthews, Kennith; Pulsipher, Allan; Wang, Wei-Hsung

2016-02-01

Radioactive waste is an inevitable product of using radioactive material in education and research activities, medical applications, energy generation, and weapons production. Low-level radioactive waste (LLW) makes up a majority of the radioactive waste produced in the United States. In 2010, over two million cubic feet of LLW were shipped to disposal sites. Despite efforts from several states and compacts as well as from private industry, the options for proper disposal of LLW remain limited. New methods for quickly identifying potential storage locations could alleviate current challenges and eventually provide additional sites and allow for adequate regional disposal of LLW. Furthermore, these methods need to be designed so that they are easily communicated to the public. A Geographic Information Systems (GIS) based method was developed to determine suitability of potential LLW disposal (or storage) sites. Criteria and other parameters of suitability were based on the Code of Federal Regulation (CFR) requirements as well as supporting literature and reports. The resultant method was used to assess areas suitable for further evaluation as prospective disposal sites in Louisiana. Criteria were derived from the 10 minimum requirements in 10 CFR Part 61.50, the Nuclear Regulatory Commission's Regulatory Guide 0902, and studies at existing disposal sites. A suitability formula was developed permitting the use of weighting factors and normalization of all criteria. Data were compiled into GIS data sets and analyzed on a cell grid of approximately 14,000 cells (covering 181,300 square kilometers) using the suitability formula. Requirements were analyzed for each cell using multiple criteria/sub-criteria as well as surrogates for unavailable datasets. Additional criteria were also added when appropriate. The method designed in this project proved to be sufficient for initial screening tests in determining the most suitable areas for prospective disposal (or storage

Stability of picrotoxin during yogurt manufacture and storage.

Science.gov (United States)

Jablonski, J E; Jackson, L S

2008-10-01

Picrotoxin is a neurotoxin found in the berries of Anamirta cocculus, a plant native to Southeast Asia. Picrotoxin has potential for being used as a biological weapon since the toxin is relatively easy to isolate and purify. Limited information exists on the stability and detection of picrotoxin added to foods before or after processing. The objective of this study was to determine the stability of picrotoxin during yogurt manufacture and storage. Direct, cup-set yogurt was produced by using methods that mimic the conditions used in full-scale production of yogurt. Milk (full-fat or low-fat) was pasteurized at 85 degrees C for 30 min, and then cooled to 43 degrees C. Yogurt starter culture (thermophilic culture or thermophilic + probiotic culture) and picrotoxin (200 mug/mL milk) were added. Samples of yogurt during fermentation (5 to 6 h, 43 degrees C) and during 30 d refrigerated (4 to 6 degrees C) storage were analyzed for pH, titratable acidity, and picrototoxin levels. Regardless of starter culture used or fat content of milk, there were no significant differences in the pH and titratable acidities of the picrotoxin-spiked yogurt and the control yogurt (no added picrotoxin) during fermentation and up to 4 wk of refrigerated storage. The color or texture of the yogurt was not affected by addition of picrotoxin. Levels of picrotoxinin and picrotin (components of picrotoxin) in yogurt, as measured by LC/MS (APCI(+)/SIR) did not change significantly during fermentation and storage. A separate experiment determined that addition of picrotoxin to milk before pasteurization (85 degrees C, 30 min) did not affect picrotoxin stability. These results indicate that picrotoxin is stable in yogurt during manufacture and storage.

Calcine Waste Storage at the Idaho Nuclear Technology and Engineering Center

Energy Technology Data Exchange (ETDEWEB)

M. D. Staiger

1999-06-01

A potential option in the program for long-term management of high-level wastes at the Idaho Nuclear Technology and Engineering Center (INTEC), at the Idaho National Engineering and Environmental Laboratory, calls for retrieving calcine waste and converting it to a more stable and less dispersible form. An inventory of calcine produced during the period December 1963 to May 1999 has been prepared based on calciner run, solids storage facilities operating, and miscellaneous operational information, which gives the range of chemical compositions of calcine waste stored at INTEC. Information researched includes calciner startup data, waste solution analyses and volumes calcined, calciner operating schedules, solids storage bin capacities, calcine storage bin distributor systems, and solids storage bin design and temperature monitoring records. Unique information on calcine solids storage facilities design of potential interest to remote retrieval operators is given.

Storage of water reactor spent fuel in water pools. Survey of world experience

International Nuclear Information System (INIS)

1982-01-01

Following discharge from a nuclear reactor, spent fuel has to be stored in water pools at the reactor site to allow for radioactive decay and cooling. After this initial storage period, the future treatment of spent fuel depends on the fuel cycle concept chosen. Spent fuel can either be treated by chemical processing or conditioning for final disposal at the relevant fuel cycle facilities, or be held in interim storage - at the reactor site or at a central storage facility. Recent forecasts predict that, by the year 2000, more than 150,000 tonnes of heavy metal from spent LWR fuel will have been accumulated. Because of postponed commitments regarding spent fuel treatment, a significant amount of spent fuel will still be held in storage at that time. Although very positive experience with wet storage has been gained over the past 40 years, making wet storage a proven technology, it appears desirable to summarize all available data for the benefit of designers, storage pool operators, licensing agenices and the general public. Such data will be essential for assessing the viability of extended water pool storage of spent nuclear fuel. In 1979, the International Atomic Energy Agency and the Nuclear Energy Agency of the OECD jointly issued a questionnaire dealing with all aspects of water pool storage. This report summarizes the information received from storage pool operators

Advanced materials for energy storage.

Science.gov (United States)

Liu, Chang; Li, Feng; Ma, Lai-Peng; Cheng, Hui-Ming

2010-02-23

Popularization of portable electronics and electric vehicles worldwide stimulates the development of energy storage devices, such as batteries and supercapacitors, toward higher power density and energy density, which significantly depends upon the advancement of new materials used in these devices. Moreover, energy storage materials play a key role in efficient, clean, and versatile use of energy, and are crucial for the exploitation of renewable energy. Therefore, energy storage materials cover a wide range of materials and have been receiving intensive attention from research and development to industrialization. In this Review, firstly a general introduction is given to several typical energy storage systems, including thermal, mechanical, electromagnetic, hydrogen, and electrochemical energy storage. Then the current status of high-performance hydrogen storage materials for on-board applications and electrochemical energy storage materials for lithium-ion batteries and supercapacitors is introduced in detail. The strategies for developing these advanced energy storage materials, including nanostructuring, nano-/microcombination, hybridization, pore-structure control, configuration design, surface modification, and composition optimization, are discussed. Finally, the future trends and prospects in the development of advanced energy storage materials are highlighted.

Cost-effective data storage/archival subsystem for functional PACS

Science.gov (United States)

Chen, Y. P.; Kim, Yongmin

1993-09-01

Not the least of the requirements of a workable PACS is the ability to store and archive vast amounts of information. A medium-size hospital will generate between 1 and 2 TBytes of data annually on a fully functional PACS. A high-speed image transmission network coupled with a comparably high-speed central data storage unit can make local memory and magnetic disks in the PACS workstations less critical and, in an extreme case, unnecessary. Under these circumstances, the capacity and performance of the central data storage subsystem and database is critical in determining the response time at the workstations, thus significantly affecting clinical acceptability. The central data storage subsystem not only needs to provide sufficient capacity to store about ten days worth of images (five days worth of new studies, and on the average, about one comparison study for each new study), but also supplies images to the requesting workstation in a timely fashion. The database must provide fast retrieval responses upon users' requests for images. This paper analyzes both advantages and disadvantages of multiple parallel transfer disks versus RAID disks for short-term central data storage subsystem, as well as optical disk jukebox versus digital recorder tape subsystem for long-term archive. Furthermore, an example high-performance cost-effective storage subsystem which integrates both the RAID disks and high-speed digital tape subsystem as a cost-effective PACS data storage/archival unit are presented.

High Efficiency and Low Cost Thermal Energy Storage System

Energy Technology Data Exchange (ETDEWEB)

Sienicki, James J. [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Lv, Qiuping [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Moisseytsev, Anton [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Bucknor, Matthew [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division

2017-09-29

BgtL, LLC (BgtL) is focused on developing and commercializing its proprietary compact technology for processes in the energy sector. One such application is a compact high efficiency Thermal Energy Storage (TES) system that utilizes the heat of fusion through phase change between solid and liquid to store and release energy at high temperatures and incorporate state-of-the-art insulation to minimize heat dissipation. BgtL’s TES system would greatly improve the economics of existing nuclear and coal-fired power plants by allowing the power plant to store energy when power prices are low and sell power into the grid when prices are high. Compared to existing battery storage technology, BgtL’s novel thermal energy storage solution can be significantly less costly to acquire and maintain, does not have any waste or environmental emissions, and does not deteriorate over time; it can keep constant efficiency and operates cleanly and safely. BgtL’s engineers are experienced in this field and are able to design and engineer such a system to a specific power plant’s requirements. BgtL also has a strong manufacturing partner to fabricate the system such that it qualifies for an ASME code stamp. BgtL’s vision is to be the leading provider of compact systems for various applications including energy storage. BgtL requests that all technical information about the TES designs be protected as proprietary information. To honor that request, only non-proprietay summaries are included in this report.

Summary Report for Capsule Dry Storage Project

Energy Technology Data Exchange (ETDEWEB)

JOSEPHSON, W S

2003-09-04

There are 1.936 cesium (Cs) and strontium (Sr) capsules stored in pools at the Waste Encapsulation and Storage Facility (WESF). These capsules will be moved to dry storage on the Hanford Site as an interim measure to reduce risk. The Cs/Sr Capsule Dry Storage Project (CDSP) is conducted under the assumption the capsules will eventually be moved to the repository at Yucca Mountain, and the design criteria include requirements that will facilitate acceptance at the repository. The storage system must also permit retrieval of capsules in the event vitrification of the capsule contents is pursued. A cut away drawing of a typical cesium chloride (CsCI) capsule and the capsule property and geometry information are provided in Figure 1.1. Strontium fluoride (SrF{sub 2}) capsules are similar in design to CsCl capsules. Further details of capsule design, current state, and reference information are given later in this report and its references. Capsule production and life history is covered in WMP-16938, Capsule Characterization Report for Capsule Dry Storage Project, and is briefly summarized in Section 5.2 of this report.

Microbial Internal Storage Alters the Carbon Transformation in Dynamic Anaerobic Fermentation.

Science.gov (United States)

Ni, Bing-Jie; Batstone, Damien; Zhao, Bai-Hang; Yu, Han-Qing

2015-08-04

Microbial internal storage processes have been demonstrated to occur and play an important role in activated sludge systems under both aerobic and anoxic conditions when operating under dynamic conditions. High-rate anaerobic reactors are often operated at a high volumetric organic loading and a relatively dynamic profile, with large amounts of fermentable substrates. These dynamic operating conditions and high catabolic energy availability might also facilitate the formation of internal storage polymers by anaerobic microorganisms. However, so far information about storage under anaerobic conditions (e.g., anaerobic fermentation) as well as its consideration in anaerobic process modeling (e.g., IWA Anaerobic Digestion Model No. 1, ADM1) is still sparse. In this work, the accumulation of storage polymers during anaerobic fermentation was evaluated by batch experiments using anaerobic methanogenic sludge and based on mass balance analysis of carbon transformation. A new mathematical model was developed to describe microbial storage in anaerobic systems. The model was calibrated and validated by using independent data sets from two different anaerobic systems, with significant storage observed, and effectively simulated in both systems. The inclusion of the new anaerobic storage processes in the developed model allows for more successful simulation of transients due to lower accumulation of volatile fatty acids (correction for the overestimation of volatile fatty acids), which mitigates pH fluctuations. Current models such as the ADM1 cannot effectively simulate these dynamics due to a lack of anaerobic storage mechanisms.

190-C Facility <90 Day Storage Pad supplemental information to the Hanford facility contingency plan

International Nuclear Information System (INIS)

Little, N.C.

1996-12-01

The 190-C Facility <90 Day Storage Pad stores waste oils primarily contaminated with lead generated while draining equipment within the building of residual lubricating oils. Waste oils are packaged and stored in fifty-five gallon drums, or other containers permitted by the Site Specific Waste Management Instruction. Bechtel Hanford, Inc. (BHI) manual BHI-EE-02, Environmental Requirements Procedures, references this document. This document is to be used to demonstrate compliance with the contingency plan requirements in Washington Administrative Code, Chapter 173-303, Dangerous Waste Regulations, for certain Resource Conservation and Recovery Act of 1976 (RCRA) waste management units (units). Refer to BHI-EE-02, for additional information

Cloud Computing Application on Transport Dispatching Informational Support Systems

Directory of Open Access Journals (Sweden)

Dmitry Olegovich Gusenitsa

2015-05-01

Full Text Available Transport dispatching informational support systems has received widespread attention due to high quality information density, strong coherence and applicable visualization features. Nevertheless, because of large volume of data, complex integration requirements and the need for information exchange between different users, time costs of the development and implementation of the informational support systems, problems associated with various data formats compatibility, security protocols and high maintenance cost, the opportunities for the application of such systems are significantly reduced. This article reviews the possibility of creating a cloud storage data system for transport dispatching informational support system (TDIS using modern computer technology to meet the challenges of mass data processing, information security and reduce operational costs. The system is expected to make full use of the advantages offered by the technology of cloud storage. Integrated cloud will increase the amount of data available to the system, reduce the speed processing requirements and reduce the overall cost of system implementation. Creation and integration of cloud storage is one of the most important areas of TDIS development, which is stimulating and promoting the further development of TDIS to ensure the requirements of its users.

Holographic memory for high-density data storage and high-speed pattern recognition

Science.gov (United States)

Gu, Claire

2002-09-01

As computers and the internet become faster and faster, more and more information is transmitted, received, and stored everyday. The demand for high density and fast access time data storage is pushing scientists and engineers to explore all possible approaches including magnetic, mechanical, optical, etc. Optical data storage has already demonstrated its potential in the competition against other storage technologies. CD and DVD are showing their advantages in the computer and entertainment market. What motivated the use of optical waves to store and access information is the same as the motivation for optical communication. Light or an optical wave has an enormous capacity (or bandwidth) to carry information because of its short wavelength and parallel nature. In optical storage, there are two types of mechanism, namely localized and holographic memories. What gives the holographic data storage an advantage over localized bit storage is the natural ability to read the stored information in parallel, therefore, meeting the demand for fast access. Another unique feature that makes the holographic data storage attractive is that it is capable of performing associative recall at an incomparable speed. Therefore, volume holographic memory is particularly suitable for high-density data storage and high-speed pattern recognition. In this paper, we review previous works on volume holographic memories and discuss the challenges for this technology to become a reality.

Energy storage management system with distributed wireless sensors

Science.gov (United States)

Farmer, Joseph C.; Bandhauer, Todd M.

2015-12-08

An energy storage system having a multiple different types of energy storage and conversion devices. Each device is equipped with one or more sensors and RFID tags to communicate sensor information wirelessly to a central electronic management system, which is used to control the operation of each device. Each device can have multiple RFID tags and sensor types. Several energy storage and conversion devices can be combined.

Energy storage in ceramic dielectrics

International Nuclear Information System (INIS)

Love, G.R.

1990-01-01

Historically, multilayer ceramic capacitors (MLC's) have not been considered for energy storage applications for two primary reasons. First, physically large ceramic capacitors were very expensive and, second, total energy density obtainable was not nearly so high as in electrolytic capacitor types. More recently, the fabrication technology for MLC's has improved significantly, permitting both significantly higher energy density and significantly lower costs. Simultaneously, in many applications, total energy storage has become smaller, and the secondary requirements of very low effective series resistance and effective series inductance (which, together, determine how efficiently the energy may be stored and recovered) have become more important. It is therefore desirable to reexamine energy storage in ceramics for contemporary commercial and near-commercial dielectrics. Stored energy is proportional to voltage squared only in the case of paraelectric insulators, because only they have capacitance that is independent of bias voltage. High dielectric constant materials, however, are ferroics (that is ferroelectric and/or antiferroelectric) and display significant variation of effective dielectric constant with bias voltage

Organization and costs of repurchasing, transportation, warehousing and storage of raspberry fruit

Directory of Open Access Journals (Sweden)

Kalanović-Bulatović Branka

2015-01-01

Full Text Available Due to its characteristic, apart from nutritive and medical significance, raspberry is particularly important for our country in social and economic terms, since its export attracts foreign currency inflow. Since the quality of raspberry decreases rapidly after picking, it is utterly important that the whole process, from picking to cold storage of fruit, should be rationally organized, thus finally reducing the costs and increasing the production value. For these reasons precisely the research deals with organization of the entire process, from repurchase to cold storage of raspberry fruits, as well as the analysis of pertaining costs. Necessary information for the preparation of the paper has been obtained from cold storage plants engaged in raspberry storage and preservation. Necessary information has been gathered using several methods, viz: observation, interview and content analysis methods. Furthermore, analysis, comparison and calculation methods have also been used in the preparation of the paper. The raspberry fruit repurchase, transport and storage costs range from 1,6 to 1,8 EUR per kg, exclusive of storage (store-housing. To this one should add store-housing costs ranging from 0,009 to 0,013 EUR per kg on a monthly basis. Modern organization of production and communication between producers, repurchasers, processors and exporters is essential in order to decrease fluctuations in repurchase and sales price of fresh raspberry and its products and the improvement of overall financial effect of all links within the chain of this economy activity. Cold storage plants, even if of minor capacities, are beneficial not only for the immediate participants in the producer-buyer chain, but it also makes an important stimulating factor for rural development and economy of the country.

Application of Cloud Storage on BIM Life-Cycle Management

Directory of Open Access Journals (Sweden)

Lieyun Ding

2014-08-01

Full Text Available Because of its high information intensity, strong consistency and convenient visualization features, building information modelling (BIM has received widespread attention in the fields of construction and project management. However, due to large amounts of information, high integration, the need for resource sharing between various departments, the long time-span of the BIM application, challenges relating to data interoperability, security and cost all slow down the adoption of BIM. This paper constructs a BIM cloud storage concept system using cloud storage, an advanced computer technology, to solve the problem of mass data processing, information security, and cost problems in the existing application of BIM to full life-cycle management. This system takes full advantage of the cloud storage technique. Achievements are reached in four areas of BIM information management, involving security and licensing management, file management, work process management and collaborative management. The system expands the time and space scales, improves the level of participation, and reduces the cost of BIM. The construction of the BIM cloud storage system is one of the most important directions of the development of BIM, which benefits the promotion and further development of BIM to better serve construction and engineering project management.

FutureGen 2.0 Pipeline and Regional Carbon Capture Storage Project - Final Report

Energy Technology Data Exchange (ETDEWEB)

Burger, Chris [Patrick Engineering Inc., Lisle, IL (United States); Wortman, David [Patrick Engineering Inc., Lisle, IL (United States); Brown, Chris [Battelle Memorial Inst., Richland, WA (United States); Hassan, Syed [Gulf Interstate Engineering, Houston, TX (United States); Humphreys, Ken [Futuregen Industrial Alliance, Inc., Washington, D.C. (United States); Willford, Mark [Futuregen Industrial Alliance, Inc., Washington, D.C. (United States)

2016-03-31

The U.S. Department of Energy’s (DOE) FutureGen 2.0 Program involves two projects: (1) the Oxy-Combustion Power Plant Project and (2) the CO2 Pipeline and Storage Project. This Final Technical Report is focused on the CO2 Pipeline and Storage Project. The FutureGen 2.0 CO2 Pipeline and Storage Project evolved from an initial siting and project definition effort in Phase I, into the Phase II activity consisting permitting, design development, the acquisition of land rights, facility design, and licensing and regulatory approvals. Phase II also progressed into construction packaging, construction procurement, and targeted early preparatory activities in the field. The CO2 Pipeline and Storage Project accomplishments were significant, and in some cases unprecedented. The engineering, permitting, legal, stakeholder, and commercial learnings substantially advance the nation’s understanding of commercial-scale CO2 storage in deep saline aquifers. Voluminous and significant information was obtained from the drilling and the testing program of the subsurface, and sophisticated modeling was performed that held up to a wide range of scrutiny. All designs progressed to the point of securing construction contracts or comfort letters attesting to successful negotiation of all contract terms and willing execution at the appropriate time all major project elements – pipeline, surface facilities, and subsurface – as well as operations. While the physical installation of the planned facilities did not proceed in part due to insufficient time to complete the project prior to the expiration of federal funding, the project met significant objectives prior to DOE’s closeout decision. Had additional time been available, there were no known, insurmountable obstacles that would have precluded successful construction and operation of the project. Due to the suspension of the project, site restoration activities were developed and the work was accomplished. The site restoration

Reliable IoT Storage: Minimizing Bandwidth Use in Storage Without Newcomer Nodes

DEFF Research Database (Denmark)

Zhao, Xiaobo; Lucani Rötter, Daniel Enrique; Shen, Xiaohong

2018-01-01

This letter characterizes the optimal policies for bandwidth use and storage for the problem of distributed storage in Internet of Things (IoT) scenarios, where lost nodes cannot be replaced by new nodes as is typically assumed in Data Center and Cloud scenarios. We develop an information flow...... model that captures the overall process of data transmission between IoT devices, from the initial preparation stage (generating redundancy from the original data) to the different repair stages with fewer and fewer devices. Our numerical results show that in a system with 10 nodes, the proposed optimal...

Characteristics of fuel crud and its impact on storage, handling, and shipment of spent fuel

International Nuclear Information System (INIS)

Hazelton, R.F.

1987-09-01

Corrosion products, called ''crud,'' form on out-of-reactor surfaces of nuclear reactor systems and are transported by reactor coolant to the core, where they deposit on external fuel-rod cladding surfaces and are activated by nuclear reactions. After discharge of spent fuel from a reactor, spallation of radioactive crud from the fuel rods could impact wet or dry storage operations, handling (including rod consolidation), and shipping. It is the purpose of this report to review earlier (1970s) and more recent (1980s) literature relating to crud, its characteristics, and any impact it has had on actual operations. Crud characteristics vary from reactor type to reactor type, reactor to reactor, fuel assembly to fuel assembly in a reactor, circumferentially and axially in an assembly, and from cycle to cycle for a specific facility. To characterize crud of pressurized-water (PWRs) and boiling-water reactors (BWRs), published information was reviewed on appearance, chemical composition, areal density and thickness, structure, adhesive strength, particle size, and radioactivity. Information was also collected on experience with crud during spent fuel wet storage, rod consolidation, transportation, and dry storage. From experience with wet storage, rod consolidation, transportation, and dry storage, it appears crud spallation can be managed effectively, posing no significant radiological problems. 44 refs., 11 figs

A central capacity limit to the simultaneous storage of visual and auditory arrays in working memory.

Science.gov (United States)

Saults, J Scott; Cowan, Nelson

2007-11-01

If working memory is limited by central capacity (e.g., the focus of attention; N. Cowan, 2001), then storage limits for information in a single modality should apply also to the simultaneous storage of information from different modalities. The authors investigated this by combining a visual-array comparison task with a novel auditory-array comparison task in 5 experiments. Participants were to remember only the visual, only the auditory (unimodal memory conditions), or both arrays (bimodal memory conditions). Experiments 1 and 2 showed significant dual-task tradeoffs for visual but not for auditory capacity. In Experiments 3-5, the authors eliminated modality-specific memory by using postperceptual masks. Dual-task costs occurred for both modalities, and the number of auditory and visual items remembered together was no more than the higher of the unimodal capacities (visual: 3-4 items). The findings suggest a central capacity supplemented by modality- or code-specific storage and point to avenues for further research on the role of processing in central storage. 2007 APA

Integral Monitored Retrievable Storage (MRS) Facility conceptual design report

International Nuclear Information System (INIS)

1985-09-01

This document, Volume 5 Book 7, contains cost estimate information for a monitored retrievable storage (MRS) facility. Cost estimates are for onsite improvements, waste storage, and offsite improvements for the Clinch River Site

INFORMATION SECURITY AND SECURE SEARCH OVER ENCRYPTED DATA IN CLOUD STORAGE SERVICES

OpenAIRE

Mr. A Mustagees Shaikh *; Prof. Nitin B. Raut

2016-01-01

Cloud computing is most widely used as the next generation architecture of IT enterprises, that provide convenient remote access to data storage and application services. This cloud storage can potentially bring great economical savings for data owners and users, but due to wide concerns of data owners that their private data may be exposed or handled by cloud providers. Hence end-to-end encryption techniques and fuzzy fingerprint technique have been used as solutions for secure cloud data st...

Hydrate Control for Gas Storage Operations

Energy Technology Data Exchange (ETDEWEB)

Jeffrey Savidge

2008-10-31

The overall objective of this project was to identify low cost hydrate control options to help mitigate and solve hydrate problems that occur in moderate and high pressure natural gas storage field operations. The study includes data on a number of flow configurations, fluids and control options that are common in natural gas storage field flow lines. The final phase of this work brings together data and experience from the hydrate flow test facility and multiple field and operator sources. It includes a compilation of basic information on operating conditions as well as candidate field separation options. Lastly the work is integrated with the work with the initial work to provide a comprehensive view of gas storage field hydrate control for field operations and storage field personnel.

Advanced materials for energy storage

Energy Technology Data Exchange (ETDEWEB)

Liu, Chang; Li, Feng; Ma, Lai-Peng; Cheng, Hui-Ming [Shenyang National Laboratory for Materials Science Institute of Metal Research, Chinese Academy of Sciences 72 Wenhua Road, Shenyang 110016 (China)

2010-02-23

Popularization of portable electronics and electric vehicles worldwide stimulates the development of energy storage devices, such as batteries and supercapacitors, toward higher power density and energy density, which significantly depends upon the advancement of new materials used in these devices. Moreover, energy storage materials play a key role in efficient, clean, and versatile use of energy, and are crucial for the exploitation of renewable energy. Therefore, energy storage materials cover a wide range of materials and have been receiving intensive attention from research and development to industrialization. In this review, firstly a general introduction is given to several typical energy storage systems, including thermal, mechanical, electromagnetic, hydrogen, and electrochemical energy storage. Then the current status of high-performance hydrogen storage materials for on-board applications and electrochemical energy storage materials for lithium-ion batteries and supercapacitors is introduced in detail. The strategies for developing these advanced energy storage materials, including nanostructuring, nano-/microcombination, hybridization, pore-structure control, configuration design, surface modification, and composition optimization, are discussed. Finally, the future trends and prospects in the development of advanced energy storage materials are highlighted. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

Particle data management-turning data into accessible information

International Nuclear Information System (INIS)

Bonniface, J; Coppins, G J

2007-01-01

The UKAEA has assigned significant resources to the monitoring and retrieval of particles from the vicinity of its site at Dounreay in the north of Scotland. The monitoring, retrieval and analytical processes each generate information that is required for interpretative and record purposes. As significant resources are made available for studying and retrieving particles, the information collected must be managed in a logical, stable and accessible manner to protect the investment in information. If suitable data management procedures are not in place there is a high risk of data loss and duplication, and stakeholders may be unable to discover what information is already available or be unable to access the existing information. UKAEA Dounreay operates a geographic information system (GIS) that interfaces with a data management system known as IMAGES. These systems are used to securely store and access a wide range of environmental data including those relating to particles. A case study is presented illustrating the processes and systems involved with the collection, storage, analysis and distribution of particle data. The advantages gained through use of the GIS system are considered in relation to alternative types of record management system such as paper, and electronic non-spatial systems. It is considered that the GIS system offers very significant benefits in terms of standardisation of data capture, security of storage and increased accessibility of data compared with other systems

Centralized Duplicate Removal Video Storage System with Privacy Preservation in IoT

Directory of Open Access Journals (Sweden)

Hongyang Yan

2018-06-01

Full Text Available In recent years, the Internet of Things (IoT has found wide application and attracted much attention. Since most of the end-terminals in IoT have limited capabilities for storage and computing, it has become a trend to outsource the data from local to cloud computing. To further reduce the communication bandwidth and storage space, data deduplication has been widely adopted to eliminate the redundant data. However, since data collected in IoT are sensitive and closely related to users’ personal information, the privacy protection of users’ information becomes a challenge. As the channels, like the wireless channels between the terminals and the cloud servers in IoT, are public and the cloud servers are not fully trusted, data have to be encrypted before being uploaded to the cloud. However, encryption makes the performance of deduplication by the cloud server difficult because the ciphertext will be different even if the underlying plaintext is identical. In this paper, we build a centralized privacy-preserving duplicate removal storage system, which supports both file-level and block-level deduplication. In order to avoid the leakage of statistical information of data, Intel Software Guard Extensions (SGX technology is utilized to protect the deduplication process on the cloud server. The results of the experimental analysis demonstrate that the new scheme can significantly improve the deduplication efficiency and enhance the security. It is envisioned that the duplicated removal system with privacy preservation will be of great use in the centralized storage environment of IoT.

Centralized Duplicate Removal Video Storage System with Privacy Preservation in IoT.

Science.gov (United States)

Yan, Hongyang; Li, Xuan; Wang, Yu; Jia, Chunfu

2018-06-04

In recent years, the Internet of Things (IoT) has found wide application and attracted much attention. Since most of the end-terminals in IoT have limited capabilities for storage and computing, it has become a trend to outsource the data from local to cloud computing. To further reduce the communication bandwidth and storage space, data deduplication has been widely adopted to eliminate the redundant data. However, since data collected in IoT are sensitive and closely related to users' personal information, the privacy protection of users' information becomes a challenge. As the channels, like the wireless channels between the terminals and the cloud servers in IoT, are public and the cloud servers are not fully trusted, data have to be encrypted before being uploaded to the cloud. However, encryption makes the performance of deduplication by the cloud server difficult because the ciphertext will be different even if the underlying plaintext is identical. In this paper, we build a centralized privacy-preserving duplicate removal storage system, which supports both file-level and block-level deduplication. In order to avoid the leakage of statistical information of data, Intel Software Guard Extensions (SGX) technology is utilized to protect the deduplication process on the cloud server. The results of the experimental analysis demonstrate that the new scheme can significantly improve the deduplication efficiency and enhance the security. It is envisioned that the duplicated removal system with privacy preservation will be of great use in the centralized storage environment of IoT.

Spacing Sensitivity Analysis of HLW Intermediate Storage Facility

International Nuclear Information System (INIS)

Youn, Bum Soo; Lee, Kwang Ho

2010-01-01

Currently, South Korea's spent fuels are stored in its temporary storage within the plant. But the temporary storage is expected to be reaching saturation soon. For the effective management of spent fuel wastes, the need for intermediate storage facility is a desperate position. However, the research for the intermediate storage facility for waste has not made active so far. In addition, in case of foreign countries it is mostly treated confidentially and the information isn't easy to collect. Therefore, the purpose of this study is creating the basic thermal analysis data for the waste storage facility that will be valuable in the future

Storage and Non-Payment: Persistent Informalities within the Formal Water Supply of Hubli-Dharwad, India

Directory of Open Access Journals (Sweden)

Zachary Burt

2014-02-01

Full Text Available Urban water systems in Asia and Africa mostly provide intermittent rather than continuous water supplies; such systems compromise water quality and inconvenience the user. Starting in 2008, an upgrade to continuous (24/7 water services was provided for 10% of the twin cities of Hubli-Dharwad, India, through a process of privatisation and formalisation. The goals were to improve water quality, free consumers from collecting and storing water, and reduce non-revenue (i.e. unpaid for water. Drawing on household surveys (n = 1986 conducted in 2010-2011 in the 24/7 zones, as well as on a range of interviews, we find that, even with 'formal' 24/7 water service, most consumers continue the supposedly 'informal' practices of in-home storage and water use without payment of bills. We argue that multiple unaccounted-for factors – including a history of distrust between the consumer and the utility, seemingly small infrastructural details, resistance to higher tariffs, and valuing convenience above water quality – have kept these informal practices embedded within the formalised delivery system. Our research contributes to understanding why formalisation may only partially supplant informal practices even when the formal system is functional and reliable.

Design and installation manual for thermal energy storage

Energy Technology Data Exchange (ETDEWEB)

Cole, R L; Nield, K J; Rohde, R R; Wolosewicz, R M

1980-01-01

The purpose of this manual is to provide information on the design and installation of thermal energy storage in active solar systems. It is intended for contractors, installers, solar system designers, engineers, architects, and manufacturers who intend to enter the solar energy business. The reader should have general knowledge of how solar heating and cooling systems operate and knowledge of construction methods and building codes. Knowledge of solar analysis methods such as f-Chart, SOLCOST, DOE-1, or TRNSYS would be helpful. The information contained in the manual includes sizing storage, choosing a location for the storage device, and insulation requirements. Both air-based and liquid-based systems are covered with topics on designing rock beds, tank types, pump and fan selection, installation, costs, and operation and maintenance. Topics relevant to latent heat storage include properties of phase-change materials, sizing the storage unit, insulating the storage unit, available systems, and cost. Topics relevant to heating domestic water include safety, single- and dual-tank systems, domestic water heating with air- and liquid-based space heating systems, and stand alone domestics hot water systems. Several appendices present common problems with storage systems and their solutions, heat transfer fluid properties, economic insulation thickness, heat exchanger sizing, and sample specifications for heat exchangers, wooden rock bins, steel tanks, concrete tanks, and fiberglass-reinforced plastic tanks.

SERODS: a new medium for high-density optical data storage

Science.gov (United States)

Vo-Dinh, Tuan; Stokes, David L.

1998-10-01

A new optical dada storage technology based on the surface- enhanced Raman scattering (SERS) effect has been developed for high-density optical memory and three-dimensional data storage. With the surface-enhanced Raman optical data storage (SERODS) technology, the molecular interactions between the optical layer molecules and the nanostructured metal substrate are modified by the writing laser, changing their SERS properties to encode information as bits. Since the SERS properties are extremely sensitive to molecular nano- environments, very small 'spectrochemical holes' approaching the diffraction limit can be produced for the writing process. The SERODS device uses a reading laser to induce the SERS emission of molecules on the disk and a photometric detector tuned to the frequency of the RAMAN spectrum to retrieve the stored information. The results illustrate that SERODS is capable of three-dimensional data storage and has the potential to achieve higher storage density than currently available optical data storage systems.

Long-term data storage in diamond

Science.gov (United States)

Dhomkar, Siddharth; Henshaw, Jacob; Jayakumar, Harishankar; Meriles, Carlos A.

2016-01-01

The negatively charged nitrogen vacancy (NV−) center in diamond is the focus of widespread attention for applications ranging from quantum information processing to nanoscale metrology. Although most work so far has focused on the NV− optical and spin properties, control of the charge state promises complementary opportunities. One intriguing possibility is the long-term storage of information, a notion we hereby introduce using NV-rich, type 1b diamond. As a proof of principle, we use multicolor optical microscopy to read, write, and reset arbitrary data sets with two-dimensional (2D) binary bit density comparable to present digital-video-disk (DVD) technology. Leveraging on the singular dynamics of NV− ionization, we encode information on different planes of the diamond crystal with no cross-talk, hence extending the storage capacity to three dimensions. Furthermore, we correlate the center’s charge state and the nuclear spin polarization of the nitrogen host and show that the latter is robust to a cycle of NV− ionization and recharge. In combination with super-resolution microscopy techniques, these observations provide a route toward subdiffraction NV charge control, a regime where the storage capacity could exceed present technologies. PMID:27819045

Long-term data storage in diamond.

Science.gov (United States)

Dhomkar, Siddharth; Henshaw, Jacob; Jayakumar, Harishankar; Meriles, Carlos A

2016-10-01

The negatively charged nitrogen vacancy (NV - ) center in diamond is the focus of widespread attention for applications ranging from quantum information processing to nanoscale metrology. Although most work so far has focused on the NV - optical and spin properties, control of the charge state promises complementary opportunities. One intriguing possibility is the long-term storage of information, a notion we hereby introduce using NV-rich, type 1b diamond. As a proof of principle, we use multicolor optical microscopy to read, write, and reset arbitrary data sets with two-dimensional (2D) binary bit density comparable to present digital-video-disk (DVD) technology. Leveraging on the singular dynamics of NV - ionization, we encode information on different planes of the diamond crystal with no cross-talk, hence extending the storage capacity to three dimensions. Furthermore, we correlate the center's charge state and the nuclear spin polarization of the nitrogen host and show that the latter is robust to a cycle of NV - ionization and recharge. In combination with super-resolution microscopy techniques, these observations provide a route toward subdiffraction NV charge control, a regime where the storage capacity could exceed present technologies.

Standard review plan for dry cask storage systems. Final report

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-01-01

The Standard Review Plan (SRP) For Dry Cask Storage Systems provides guidance to the Nuclear Regulatory Commission staff in the Spent Fuel Project Office for performing safety reviews of dry cask storage systems. The SRP is intended to ensure the quality and uniformity of the staff reviews, present a basis for the review scope, and clarification of the regulatory requirements. Part 72, Subpart B generally specifies the information needed in a license application for the independent storage of spent nuclear fuel and high level radioactive waste. Regulatory Guide 3.61 {open_quotes}Standard Format and Content for a Topical Safety Analysis Report for a Spent Fuel Dry Storage Cask{close_quotes} contains an outline of the specific information required by the staff. The SRP is divided into 14 sections which reflect the standard application format. Regulatory requirements, staff positions, industry codes and standards, acceptance criteria, and other information are discussed.

Standard review plan for dry cask storage systems. Final report

International Nuclear Information System (INIS)

1997-01-01

The Standard Review Plan (SRP) For Dry Cask Storage Systems provides guidance to the Nuclear Regulatory Commission staff in the Spent Fuel Project Office for performing safety reviews of dry cask storage systems. The SRP is intended to ensure the quality and uniformity of the staff reviews, present a basis for the review scope, and clarification of the regulatory requirements. Part 72, Subpart B generally specifies the information needed in a license application for the independent storage of spent nuclear fuel and high level radioactive waste. Regulatory Guide 3.61 open-quotes Standard Format and Content for a Topical Safety Analysis Report for a Spent Fuel Dry Storage Caskclose quotes contains an outline of the specific information required by the staff. The SRP is divided into 14 sections which reflect the standard application format. Regulatory requirements, staff positions, industry codes and standards, acceptance criteria, and other information are discussed

Rock cavern storage of spent fuel

Energy Technology Data Exchange (ETDEWEB)

Cho, Won Jin; Kim, Kyung Soo [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Kwon, Sang Ki [Inha University, Incheon (Korea, Republic of)

2015-12-15

The rock cavern storage for spent fuel has been assessed to apply in Korea with reviewing the state of the art of the technologies for surface storage and rock cavern storage of spent fuel. The technical feasibility and economic aspects of the rock cavern storage of spent fuel were also analyzed. A considerable area of flat land isolated from the exterior are needed to meet the requirement for the site of the surface storage facilities. It may, however, not be easy to secure such areas in the mountainous region of Korea. Instead, the spent fuel storage facilities constructed in the rock cavern moderate their demands for the suitable site. As a result, the rock cavern storage is a promising alternative for the storage of spent fuel in the aspect of natural and social environments. The rock cavern storage of spent fuel has several advantages compared with the surface storage, and there is no significant difference on the viewpoint of economy between the two alternatives. In addition, no great technical difficulties are present to apply the rock cavern storage technologies to the storage of domestic spent fuel.

Physics and technology of optical storage in polymer thin films

DEFF Research Database (Denmark)

Ramanujam, P.S.; Hvilsted, Søren; Ujhelyi, F.

2001-01-01

We discuss different strategies for optical storage of information in polymeric films. An outline of the existing trends is given. The synthesis and characterization of side-chain azobenzene polyester films for holographic storage of information is described. A compact holographic memory card...... system based on polarization holography is described. A storage density of greater than 10MB/cm2 has been achieved so far, with a potential increase to 100MB/cm(2) using multiplexing techniques and software correction. Finally the role of surface relief in azobenzene polymers on irradiation...

The socio-technical transition of distributed electricity storage into future networks—System value and stakeholder views

International Nuclear Information System (INIS)

Grünewald, Philipp H.; Cockerill, Timothy T.; Contestabile, Marcello; Pearson, Peter J.G.

2012-01-01

Whole system models for the GB electricity system suggest that distributed electricity storage has the potential to significantly reduce the system integration cost for future system scenarios. From a policy perspective, this poses the question why this value should not be realised within existing market structures. Opinion among stakeholders is divided. Some believe that storage deployment constitutes a ‘special case’ in need of policy support. Others insist that markets can provide the necessary platform to negotiate contracts, which reward storage operators for the range of services they could provide. This paper seeks to inform this debate with a process of stakeholder engagement using a perspective informed by socio-technical transition literatures. This approach allows the identification of tensions among actors in the electricity system and of possibilities for co-evolution in the deployment of storage technologies during a transition towards a low carbon electricity system. It also draws attention to policy-related challenges of technology lock-in and path dependency resulting from poor alignment of incumbent regimes with the requirements for distributed electricity storage. - Highlights: ► Electricity storage is poorly aligned with existing regimes in the electricity system. ► Stakeholders perceive electricity storage as “somebody else's problem”. ► Combining stakeholder views and transition theory provides new insight. ► Transition from network to operational benefits poses regulatory challenge. ► Value aggregation made difficult due to institutional barriers.

Nuclear materials management storage study

International Nuclear Information System (INIS)

Becker, G.W. Jr.

1994-02-01

The Office of Weapons and Materials Planning (DP-27) requested the Planning Support Group (PSG) at the Savannah River Site to help coordinate a Departmental complex-wide nuclear materials storage study. This study will support the development of management strategies and plans until Defense Programs' Complex 21 is operational by DOE organizations that have direct interest/concerns about or responsibilities for nuclear material storage. They include the Materials Planning Division (DP-273) of DP-27, the Office of the Deputy Assistant Secretary for Facilities (DP-60), the Office of Weapons Complex Reconfiguration (DP-40), and other program areas, including Environmental Restoration and Waste Management (EM). To facilitate data collection, a questionnaire was developed and issued to nuclear materials custodian sites soliciting information on nuclear materials characteristics, storage plans, issues, etc. Sites were asked to functionally group materials identified in DOE Order 5660.1A (Management of Nuclear Materials) based on common physical and chemical characteristics and common material management strategies and to relate these groupings to Nuclear Materials Management Safeguards and Security (NMMSS) records. A database was constructed using 843 storage records from 70 responding sites. The database and an initial report summarizing storage issues were issued to participating Field Offices and DP-27 for comment. This report presents the background for the Storage Study and an initial, unclassified summary of storage issues and concerns identified by the sites

Optimization of Munitions Storage.

Science.gov (United States)

1979-12-01

zones of land around each facility place a significant economic cost on the storage of munitions (Schreyer, 1970: 1). Munitions storage is a subject...ADDTOT, BTOTAL 353 REAL MPH,MW ,MPD, MPU ,4,MPNEW,MCD 354 IF (SW2.NE.0) GO TO 1 355 SW2 - 1 356 WRITE (6,2) 357 GO TO 3 358 1 IF (REC.EQ.0) GO TO 4 359 IF

Energy storage

International Nuclear Information System (INIS)

Anon.

1992-01-01

This chapter discusses the role that energy storage may have on the energy future of the US. The topics discussed in the chapter include historical aspects of energy storage, thermal energy storage including sensible heat storage, latent heat storage, thermochemical heat storage, and seasonal heat storage, electricity storage including batteries, pumped hydroelectric storage, compressed air energy storage, and superconducting magnetic energy storage, and production and combustion of hydrogen as an energy storage option

Twelve Principles for Green Energy Storage in Grid Applications.

Science.gov (United States)

Arbabzadeh, Maryam; Johnson, Jeremiah X; Keoleian, Gregory A; Rasmussen, Paul G; Thompson, Levi T

2016-01-19

The introduction of energy storage technologies to the grid could enable greater integration of renewables, improve system resilience and reliability, and offer cost effective alternatives to transmission and distribution upgrades. The integration of energy storage systems into the electrical grid can lead to different environmental outcomes based on the grid application, the existing generation mix, and the demand. Given this complexity, a framework is needed to systematically inform design and technology selection about the environmental impacts that emerge when considering energy storage options to improve sustainability performance of the grid. To achieve this, 12 fundamental principles specific to the design and grid application of energy storage systems are developed to inform policy makers, designers, and operators. The principles are grouped into three categories: (1) system integration for grid applications, (2) the maintenance and operation of energy storage, and (3) the design of energy storage systems. We illustrate the application of each principle through examples published in the academic literature, illustrative calculations, and a case study with an off-grid application of vanadium redox flow batteries (VRFBs). In addition, trade-offs that can emerge between principles are highlighted.

Impact of storage environment on the efficacy of hermetic storage bags.

Science.gov (United States)

Lane, Brett; Woloshuk, Charles

2017-05-01

Small hermetic bags (50 and 100 kg capacities) used by smallholder farmers in several African countries have proven to be a low-cost solution for preventing storage losses due to insects. The complexity of postharvest practices and the need for ideal drying conditions, especially in the Sub-Sahara, has led to questions about the efficacy of the hermetic bags for controlling spoilage by fungi and the potential for mycotoxin accumulation. This study compared the effects of environmental temperature and relative humidity at two locations (Indiana and Arkansas) on dry maize (14% moisture content) in woven polypropylene bags and Purdue Improved Crop Storage (PICS) hermetic bags. Temperature and relative humidity data loggers placed in the middle of each bag provided profiles of environmental influences on stored grain at the two locations. The results indicated that the PICS bags prevented moisture penetration over the three-month storage period. In contrast, maize in the woven bags increased in moisture content. For both bag types, no evidence was obtained indicating the spread of Aspergillus flavus from colonized maize to adjacent non-colonized maize. However, other storage fungi did increase during storage. The number of infected kernels did not increase in the PICS bags, but the numbers in the woven bags increased significantly. The warmer environment in Arkansas resulted in significantly higher insect populations in the woven bags than in Indiana. Insects in the PICS bags remained low at both locations. This study demonstrates that the PICS hermetic bags are effective at blocking the effects of external humidity fluctuations as well as the spread of fungi to non-infected kernels.

Old radioactive waste storage sites

International Nuclear Information System (INIS)

2008-01-01

After a recall of the regulatory context for the management of old sites used for the storage of radioactive wastes with respect with their activity, the concerned products, the disposal or storage type, this document describes AREVA's involvement in the radioactive waste management process in France. Then, for the different kinds of sites (currently operated sites having radioactive waste storage, storage sites for uranium mineral processing residues), it indicates their location and name, their regulatory status and their control authority, the reference documents. It briefly presents the investigation on the long term impact of uranium mineral processing residues on health and environment, evokes some aspects of public information transparency, and presents the activities of an expertise group on old uranium mines. The examples of the sites of Bellezane (uranium mineral processing residues) and COMURHEX Malvesi (assessment of underground and surface water quality at the vicinity of this installation) are given in appendix

Fuel handling and storage systems in nuclear power plants

International Nuclear Information System (INIS)

1984-01-01

The scope of this Guide includes the design of handling and storage facilities for fuel assemblies from the receipt of fuel into the nuclear power plant until the fuel departs from that plant. The unirradiated fuel considered in this Guide is assumed not to exhibit any significant level of radiation so that it can be handled without shielding or cooling. This Guide also gives limited consideration to the handling and storage of certain core components. While the general design and safety principles are discussed in Section 2 of this Guide, more specific design requirements for the handling and storage of fuel are given in detailed sections which follow the general design and safety principles. Further useful information is to be found in the IAEA Technical Reports Series No. 189 ''Storage, Handling and Movement of Fuel and Related Components at Nuclear Power Plants'' and No. 198 ''Guide to the Safe Handling of Radioactive Wastes at Nuclear Power Plants''. However, the scope of the Guide does not include consideration of the following: (1) The various reactor physics questions associated with fuel and absorber loading and unloading into the core; (2) The design aspects of preparation of the reactor for fuel loading (such as the removal of the pressure vessel head for a light water reactor) and restoration after loading; (3) The design of shipping casks; (4) Fuel storage of a long-term nature exceeding the design lifetime of the nuclear power plant; (5) Unirradiated fuel containing plutonium

From Drought to Recovery: a GRACE-Based Assessment of Groundwater Storage Variations in California

Science.gov (United States)

McEvoy, A.; Famiglietti, J. S.; Liu, P. W.; Reager, J. T., II

2017-12-01

The 2011-2015 drought in California was the most severe on record and significantly depleted state water reserves. However, after the consecutive wet winters of 2015-16 and 2016-17, water storage in reservoirs, soil, snowpack, and aquifers began recovering and the state government lifted the drought emergency for all California counties except four. But is the drought really "over"? Quantifiable metrics of groundwater storage are necessary to provide such evidence, yet in situ measurements are sparse at best. Here we holistically test whether California state water resources have fully recovered in the Sacramento, San Joaquin, and Tulare Lake basins of California, using remote sensing satellite observations, in situ measurements, and numerical models. Specifically, we partition water storage into four components of the terrestrial water cycle: soil moisture, snow water equivalent, surface water, and groundwater. We derive soil moisture and snow water equivalent from the North American Land Data Assimilation System (NLDAS) and we use the California Data Exchange Center (CDEC) network to measure in situ reservoir storage. To estimate changes in groundwater storage, we subtract these three components from the total water storage derived from the Gravity Recovery and Climate Experiment (GRACE) satellite. Preliminary results show that the groundwater storage plummeted to a record low during the 2011-2015 drought. The results also show a rapid recovery in total water storage from 2015-2017. Moreover, we find that groundwater accounts for, on average, 60% of the total water storage variations in the study basins. Our results hold social significance when placed in the context of arid California: Did the groundwater recover? Is this the largest recovery that California can expect? Finally, our results have implications for the utility of remote sensing to inform water resource management decisions.

Public Acceptance for Geological CO2-Storage

Science.gov (United States)

Schilling, F.; Ossing, F.; Würdemann, H.; Co2SINK Team

2009-04-01

Public acceptance is one of the fundamental prerequisites for geological CO2 storage. In highly populated areas like central Europe, especially in the vicinity of metropolitan areas like Berlin, underground operations are in the focus of the people living next to the site, the media, and politics. To gain acceptance, all these groups - the people in the neighbourhood, journalists, and authorities - need to be confident of the security of the planned storage operation as well as the long term security of storage. A very important point is to show that the technical risks of CO2 storage can be managed with the help of a proper short and long term monitoring concept, as well as appropriate mitigation technologies e.g adequate abandonment procedures for leaking wells. To better explain the possible risks examples for leakage scenarios help the public to assess and to accept the technical risks of CO2 storage. At Ketzin we tried the following approach that can be summed up on the basis: Always tell the truth! This might be self-evident but it has to be stressed that credibility is of vital importance. Suspiciousness and distrust are best friends of fear. Undefined fear seems to be the major risk in public acceptance of geological CO2-storage. Misinformation and missing communication further enhance the denial of geological CO2 storage. When we started to plan and establish the Ketzin storage site, we ensured a forward directed communication. Offensive information activities, an information centre on site, active media politics and open information about the activities taking place are basics. Some of the measures were: - information of the competent authorities through meetings (mayor, governmental authorities) - information of the local public, e.g. hearings (while also inviting local, regional and nation wide media) - we always treated the local people and press first! - organizing of bigger events to inform the public on site, e.g. start of drilling activities (open

Pyridostimine Bromide 30mg Stability in Extended Storage Conditions

Science.gov (United States)

2017-12-03

States Pharmacopeia (USP) >. The real-life storage conditions will be determined using the International Commission for Harmonization’s (ICH) Quality ...Packaging and Storage Requirements. 4 ~ Real-life storage conditions are defined based on the International Council for Harmonisation’s (ICH) Quality ...information, including suggestions for reducing the burden, to the Department of Defense, Executive Service Directorate {0704-0188). Respondents should be

Efficiency of Compressed Air Energy Storage

DEFF Research Database (Denmark)

Elmegaard, Brian; Brix, Wiebke

2011-01-01

The simplest type of a Compressed Air Energy Storage (CAES) facility would be an adiabatic process consisting only of a compressor, a storage and a turbine, compressing air into a container when storing and expanding when producing. This type of CAES would be adiabatic and would if the machines...... were reversible have a storage efficiency of 100%. However, due to the specific capacity of the storage and the construction materials the air is cooled during and after compression in practice, making the CAES process diabatic. The cooling involves exergy losses and thus lowers the efficiency...... of the storage significantly. The efficiency of CAES as an electricity storage may be defined in several ways, we discuss these and find that the exergetic efficiency of compression, storage and production together determine the efficiency of CAES. In the paper we find that the efficiency of the practical CAES...

The Aube storage centre: Annual report 2010

International Nuclear Information System (INIS)

2011-01-01

After a presentation of the Aube storage centre, a storage centre for low and intermediate activity nuclear wastes, this report gives an overview of measures related to nuclear security, to radioprotection and to nuclear safety. It indicates the incidents and accidents which occurred in 2010, describes how the centre's wastes are managed, and indicates the actions performed in terms of public information

Technology for organization of the onboard system for processing and storage of ERS data for ultrasmall spacecraft

Science.gov (United States)

Strotov, Valery V.; Taganov, Alexander I.; Konkin, Yuriy V.; Kolesenkov, Aleksandr N.

2017-10-01

Task of processing and analysis of obtained Earth remote sensing data on ultra-small spacecraft board is actual taking into consideration significant expenditures of energy for data transfer and low productivity of computers. Thereby, there is an issue of effective and reliable storage of the general information flow obtained from onboard systems of information collection, including Earth remote sensing data, into a specialized data base. The paper has considered peculiarities of database management system operation with the multilevel memory structure. For storage of data in data base the format has been developed that describes a data base physical structure which contains required parameters for information loading. Such structure allows reducing a memory size occupied by data base because it is not necessary to store values of keys separately. The paper has shown architecture of the relational database management system oriented into embedment into the onboard ultra-small spacecraft software. Data base for storage of different information, including Earth remote sensing data, can be developed by means of such database management system for its following processing. Suggested database management system architecture has low requirements to power of the computer systems and memory resources on the ultra-small spacecraft board. Data integrity is ensured under input and change of the structured information.

Information and knowledge: an evolutionary framework for information science

Directory of Open Access Journals (Sweden)

Marcia J. Bates

2005-01-01

Full Text Available Background. Many definitions of information, knowledge, and data have been suggested throughout the history of information science. In this article, the objective is to provide definitions that are usable for the physical, biological, and social meanings of the terms, covering the various senses important to our field. Argument. Information 1 is defined as the pattern of organization of matter and energy. Information 2 is defined as some pattern of organization of matter and energy that has been given meaning by a living being. Knowledge is defined as information given meaning and integrated with other contents of understanding. Elaboration. The approach is rooted in an evolutionary framework; that is, modes of information perception, processing, transmission, and storage are seen to have developed as a part of the general evolution of members of the animal kingdom. Brains are expensive for animals to support; consequently, efficient storage, including, particularly, storage at emergent levels-for example, storing the concept of chair, rather than specific memories of all chairs ever seen, is powerful and effective for animals. Conclusion. Thus, rather than being reductionist, the approach taken demonstrates the fundamentally emergent nature of most of what higher animals and human beings, in particular, experience as information.

an analysis of yam storage strategy to promote food security in asa

African Journals Online (AJOL)

Osondu

2012-10-17

Oct 17, 2012 ... with information regarding improved storage strategies as well as exposed to training on their use. .... be need to improve or develop new storage strategy. It is ... i. determine the various methods of yam storage strategy.

The Impact Of Optical Storage Technology On Image Processing Systems

Science.gov (United States)

Garges, Daniel T.; Durbin, Gerald T.

1984-09-01

The recent announcement of commercially available high density optical storage devices will have a profound impact on the information processing industry. Just as the initial introduction of random access storage created entirely new processing strategies, optical technology will allow dramatic changes in the storage, retrieval, and dissemination of engineering drawings and other pictorial or text-based documents. Storage Technology Corporation has assumed a leading role in this arena with the introduction of the 7600 Optical Storage Subsystem, and the formation of StorageTek Integrated Systems, a subsidiary chartered to incorporate this new technology into deliverable total systems. This paper explores the impact of optical storage technology from the perspective of a leading-edge manufacturer and integrator.

Risk assessment in long-term storage of spent nuclear fuel

International Nuclear Information System (INIS)

Ahn, T.; Guttmann, J.; Mohseni, A.

2013-01-01

This paper presents probabilistic risk-informed approaches that the Nuclear Regulatory Commission (NRC) staff is planning to consider in preparing regulatory bases for long-term storage of spent nuclear fuel (SNF) for up to 300 years. Due to uncertainties associated with long-term SNF storage, the NRC is considering a probabilistic risk-informed approach as well as a deterministic design-based approach. The uncertainties considered here are primarily associated with materials aging of the canister and SNF in the cask system during long-term storage of SNF. This paper discusses some potential risk contributors involved in long-term SNF storage. Methods of performance evaluation are presented that assess the various types of risks involved. They include deterministic evaluation, probabilistic evaluation, and consequence assessment under normal conditions and the conditions of accidents and natural hazards. Some potentially important technical issues resulting from the consideration of a probabilistic risk-informed evaluation of the cask system performance are discussed for the canister and SNF integrity. These issues are also discussed in comparison with the deterministic approach for comparison purposes, as appropriate. Probabilistic risk-informed methods can provide insights that deterministic methods may not capture. Two specific examples include stress corrosion cracking of the canister and hydrogen-induced cladding failure. These examples are discussed in more detail, in terms of their effects on radionuclide release and nuclear subcriticality associated with the failure. The plan to consider the probabilistic risk-informed approaches is anticipated to provide helpful regulatory insights for long-term storage of SNF that provide reasonable assurance for public health and safety. (authors)

Method of extracting significant trouble information of nuclear power plants using probabilistic analysis technique

International Nuclear Information System (INIS)

Shimada, Yoshio; Miyazaki, Takamasa

2005-01-01

In order to analyze and evaluate large amounts of trouble information of overseas nuclear power plants, it is necessary to select information that is significant in terms of both safety and reliability. In this research, a method of efficiently and simply classifying degrees of importance of components in terms of safety and reliability while paying attention to root-cause components appearing in the information was developed. Regarding safety, the reactor core damage frequency (CDF), which is used in the probabilistic analysis of a reactor, was used. Regarding reliability, the automatic plant trip probability (APTP), which is used in the probabilistic analysis of automatic reactor trips, was used. These two aspects were reflected in the development of criteria for classifying degrees of importance of components. By applying these criteria, a simple method of extracting significant trouble information of overseas nuclear power plants was developed. (author)

Incorrect storage of medicines and potential for cost savings

DEFF Research Database (Denmark)

Colberg, Lene; Schmidt-Petersen, Lone; Hansen, Merete Kock

2017-01-01

continue to be used, possibly with a shortened expiry date. Thus, by examining all cases of incorrect storage, the value of drugs that pharmacists advised could be used despite a broken cold chain, could be estimated. Results The Medicine Information Centre dealt with 171 cases concerning incorrect storage...... in 2013. Data show that advice from Medicine Information Centre pharmacists resulted medicine cost savings of DKK 13 million (approx. €1.7 million) in hospitals in the Capital Region for that year. Conclusions Substantial savings can be made by seeking the advice of a team of information pharmacists...

Energy Storage.

Science.gov (United States)

Eaton, William W.

Described are technological considerations affecting storage of energy, particularly electrical energy. The background and present status of energy storage by batteries, water storage, compressed air storage, flywheels, magnetic storage, hydrogen storage, and thermal storage are discussed followed by a review of development trends. Included are…

Linepack storage valuation under price uncertainty

International Nuclear Information System (INIS)

Arvesen, Ø.; Medbø, V.; Fleten, S.-E.; Tomasgard, A.; Westgaard, S.

2013-01-01

Natural gas flows in pipelines as a consequence of the pressure difference at the inlet and outlet. Adjusting these pressures makes it possible to inject natural gas at one rate and withdraw at a different rate, hence using the pipeline as storage as well as transport. We study the value of using the so called pipeline linepack as a short-term gas storage and how this functionality may offset the discrepancy between the low flexibility in take-or-pay contracts and the high inherent flexibility of a gas-fired power plant. To value the storage option, we consider a cycling power plant facing volatile power prices while purchasing gas on a take-or-pay contract. We estimate a Markov regime-switching model for power prices and a mean reverting jump diffusion model for gas prices. Applying Least Squares Monte Carlo simulation to the operation of the linepack storage, we find that the storage option indeed has significant value for the plant, enabling it to better exploit the sometimes extreme price fluctuations. Finally, we show how power price volatility and jump frequency are the main value drivers, and that the size of the storage increases the value up to a point where no additional flexibility is used. - Highlights: ► Linepack, i.e., storage of natural gas en route in long pipelines, is valued for the first time. ► We find significant storage value for a North Sea case and a German gas-fired power plant. ► Power and natural gas prices are modelled realistically, as related stochastic processes with mean reversion and spikes. ► Storage operation is valued under uncertainty yielding close to exact values, without heuristics

Secure Storage Architectures

Energy Technology Data Exchange (ETDEWEB)

Aderholdt, Ferrol [Tennessee Technological University; Caldwell, Blake A [ORNL; Hicks, Susan Elaine [ORNL; Koch, Scott M [ORNL; Naughton, III, Thomas J [ORNL; Pogge, James R [Tennessee Technological University; Scott, Stephen L [Tennessee Technological University; Shipman, Galen M [ORNL; Sorrillo, Lawrence [ORNL

2015-01-01

include evaluation of performance/protection of select products. (Note, we are investigation the option of evaluating equipment from Seagate/Xyratex.) Outline: The remainder of this report is structured as follows: - Section 1: Describes the growing importance of secure storage architectures and highlights some challenges for HPC. - Section 2: Provides background information on HPC storage architectures, relevant supporting technologies for secure storage and details on OpenStack components related to storage. Note, that background material on HPC storage architectures in this chapter can be skipped if the reader is already familiar with Lustre and GPFS. - Section 3: A review of protection mechanisms in two HPC filesystems; details about available isolation, authentication/authorization and performance capabilities are discussed. - Section 4: Describe technologies that can be used to bridge gaps in HPC storage and filesystems to facilitate...

Materials information data bank

International Nuclear Information System (INIS)

Mead, K.E.

1978-03-01

A major concern in the design of weapons systems is compatibility of materials with each other and with the enclosed environment. Usually these systems require long-term storage and must have high reliability at the end of this storage period. Materials selection is thus based on past experience and on laboratory-accelerated testing to assure this long-term reliability. To assist in materials selection, a computerized materials data bank has been established. In addition to references on personnel and documents, this data bank provides annotated information on materials so that the designer and materials engineer can draw on it for guidance in selecting materials. The primary purpose of the data bank is to provide materials compatibility data. However, the structure of the system permits the data bank to be used for storage and retrieval of general materials information. The data bank storage and information retrieval philosophy is discussed and procedures for information gathering are outlined. Examples of data entries and a list of search routines are presented to demonstrate the usefulness and versatility of the system

Considerations for Disposition of Dry Cask Storage System Materials at End of Storage System Life

International Nuclear Information System (INIS)

Howard, Rob; Van den Akker, Bret

2014-01-01

Dry cask storage systems are deployed at nuclear power plants for used nuclear fuel (UNF) storage when spent fuel pools reach their storage capacity and/or the plants are decommissioned. An important waste and materials disposition consideration arising from the increasing use of these systems is the management of the dry cask storage systems' materials after the UNF proceeds to disposition. Thermal analyses of repository design concepts currently under consideration internationally indicate that waste package sizes for the geologic media under consideration may be significantly smaller than the canisters being used for on-site dry storage by the nuclear utilities. Therefore, at some point along the UNF disposition pathway, there could be a need to repackage fuel assemblies already loaded into the dry storage canisters currently in use. In the United States, there are already over 1650 of these dry storage canisters deployed and approximately 200 canisters per year are being loaded at the current fleet of commercial nuclear power plants. There is about 10 cubic meters of material from each dry storage canister system that will need to be dispositioned. The concrete horizontal storage modules or vertical storage overpacks will need to be reused, re-purposed, recycled, or disposed of in some manner. The empty metal storage canister/cask would also have to be cleaned, and decontaminated for possible reuse or recycling or disposed of, likely as low-level radioactive waste. These material disposition options can have impacts of the overall used fuel management system costs. This paper will identify and explore some of the technical and interface considerations associated with managing the dry cask storage system materials. (authors)

Underground Storage Tanks - Storage Tank Locations

Data.gov (United States)

NSGIC Education | GIS Inventory — A Storage Tank Location is a DEP primary facility type, and its sole sub-facility is the storage tank itself. Storage tanks are aboveground or underground, and are...

Accessing leaking underground storage tank case studies and publications through the EPA's Computerized On-Line Information System (COLIS)

International Nuclear Information System (INIS)

Hillger, R.; Tibay, P.

1991-01-01

The US EPA's regulations for underground storage tanks (USTs) require corrective action to be taken in response to leaking USTs. Recent developments of UST programs nationwide as well as the introduction of new technologies to clean up UST sites have increased the diversity of experience levels among personnel involved with this type of work. The EPA's Computerized On-Line Information System (COLIS) has been developed to facilitate technology transfer among the personnel involved in UST cleanup. The system allows for the quick and simple retrieval of data relating to UST incidents, as well as other hazardous waste-related information. The system has been used by response personnel at all levels of government, academia, and private industry. Although it has been in existence for many years, users are just now realizing the potential wealth of information stored in this system. COLIS access can be accomplished via telephone lines utilizing a personal computer and a modem

Shipping and storage cask data for spent nuclear fuel

Energy Technology Data Exchange (ETDEWEB)

Johnson, E.R.; Notz, K.J.

1988-11-01

This document is a compilation of data on casks used for the storage and/or transport of commercially generated spent fuel in the US based on publicly available information. In using the information contained in the following data sheets, it should be understood that the data have been assembled from published information, which in some instances was not internally consistent. Moreover, it was sometimes necessary to calculate or infer the values of some attributes from available information. Nor was there always a uniform method of reporting the values of some attributes; for example, an outside surface dose of the loaded cask was sometimes reported to be the maximum acceptable by NRC, while in other cases the maximum actual dose rate expected was reported, and in still other cases the expected average dose rate was reported. A summary comparison of the principal attributes of storage and transportable storage casks is provided and a similar comparison for shipping casks is also shown. References to source data are provided on the individual data sheets for each cask.

Shipping and storage cask data for spent nuclear fuel

International Nuclear Information System (INIS)

Johnson, E.R.; Notz, K.J.

1988-11-01

This document is a compilation of data on casks used for the storage and/or transport of commercially generated spent fuel in the US based on publicly available information. In using the information contained in the following data sheets, it should be understood that the data have been assembled from published information, which in some instances was not internally consistent. Moreover, it was sometimes necessary to calculate or infer the values of some attributes from available information. Nor was there always a uniform method of reporting the values of some attributes; for example, an outside surface dose of the loaded cask was sometimes reported to be the maximum acceptable by NRC, while in other cases the maximum actual dose rate expected was reported, and in still other cases the expected average dose rate was reported. A summary comparison of the principal attributes of storage and transportable storage casks is provided and a similar comparison for shipping casks is also shown. References to source data are provided on the individual data sheets for each cask

Social acceptance of carbon dioxide storage

International Nuclear Information System (INIS)

Huijts, Nicole M.A.; Midden, Cees J.H.; Meijnders, Anneloes L.

2007-01-01

This article discusses public acceptance of carbon capture and storage (CCS). Responses by citizens are described in relation to responses by professionally involved actors. Interviews with members of the government, industry and environmental NGOs showed that these professional actors are interested in starting up storage projects, based on thorough evaluation processes, including discussions on multi-actor working groups. As appeared from a survey among citizens living near a potential storage site (N=103), public attitudes in general were slightly positive, but attitudes towards storage nearby were slightly negative. The general public appeared to have little knowledge about CO 2 -storage, and have little desire for more information. Under these circumstances, trust in the professional actors is particularly important. NGOs were found to be trusted most, and industry least by the general public. Trust in each of the three actors appeared to depend on perceived competence and intentions, which in turn were found to be related to perceived similarity of goals and thinking between trustee and trustor. Implications for communication about CCS are discussed. (author)

Inventory extension considerations for long-term storage at the nuclear materials storage facility

International Nuclear Information System (INIS)

Olinger, C.T.; Stanbro, W.D.; Longmire, V.; Argo, P.E.; Nielson, S.M.

1996-01-01

Los Alamos National Laboratory is in the process of modifying its nuclear materials storage facility to a long-term storage configuration. In support of this effort, we examined technical and administrative means to extend periods between physical inventories. Both the frequency and sample size during a physical inventory could significantly impact required sizing of the non-destructive assay (NDA) laboratory as well as material handling capabilities. Several options are being considered, including (1) treating each storage location as a separate vault, (2) minimizing the number of items returned for quantitative analysis by optimizing the use of in situ confirmatory measurements, and (3) utilizing advanced monitoring technologies. Careful consideration of these parameters should allow us to achieve and demonstrate safe and secure storage while minimizing the impact on facility operations and without having to increase the size of the NDA laboratory beyond that required for anticipated shipping and receiving activities

International conference on storage of spent fuel from power reactors. Book of extended synopses

International Nuclear Information System (INIS)

2003-01-01

The management of spent nuclear fuel is a key aspect characterizing the use of nuclear power around the world. At the international level, there is an ongoing debate focused on this issue. At the national level, spent fuel management often provokes public concern. Continuous attention is being given by the IAEA to the collection, analysis and exchange of information on spent fuel storage. Its role in this area is to: provide a forum for exchanging information; identify the key issues for long term storage; and co-ordinate and encourage closer co-operation among Member States in certain research and development activities that are of common interest. Meetings on this topic have been organized about once every four years since 1987. The objectives of the Conference were to: review recent advances in spent fuel storage technology; exchange information on the state of the art of and prospects for spent fuel storage; review and discuss the worldwide situation and the major factors influencing national policies in this field; exchange information on operating experience with wet and dry storage facilities; identify the most important directions for future national efforts and international co-operation in this area. The following subjects were covered in the topical sessions: National Programmes: the status and trends of spent fuel storage in Member States, spent fuel arising, amount of spent fuel stored, wet and dry storage capacities, storage facilities under construction and in planning and the national policy for the back end of the fuel cycle; Technologies: technological approaches for long term storage, new storage concepts, re-racking of fuel pools, spent fuel and material behaviour in long term storage; Experience and Licensing: experience in wet and dry storage, problems with materials in fuel pools, licensing practices for spent fuel storage facilities, license extension and re-licensing of existing facilities; R and D and Special Aspects: highly enriched fuel

Compressing Control System Data for Efficient Storage and Retrieval

International Nuclear Information System (INIS)

Christopher Larrieu

2003-01-01

The controls group at the Thomas Jefferson National Accelerator Facility (Jefferson Lab), acquires multiple terabytes of EPICS control system data per year via CZAR, its new archiving system. By heuristically applying a combination of rudimentary compression techniques, in conjunction with several specialized data transformations and algorithms, the CZAR storage engine reduces the size of this data by approximately 88 percent, without any loss of information. While the compression process requires significant memory and processor time, the decompression routine suffers only slightly in this regard

Improving wind power quality with energy storage

DEFF Research Database (Denmark)

Rasmussen, Claus Nygaard

2009-01-01

The results of simulation of the influence of energy storage on wind power quality are presented. Simulations are done using a mathematical model of energy storage. Results show the relation between storage power and energy, and the obtained increase in minimum available power from the combination...... of wind and storage. The introduction of storage enables smoothening of wind power on a timescale proportional to the storage energy. Storage does not provide availability of wind power at all times, but allows for a certain fraction of average power in a given timeframe to be available with high...... probability. The amount of storage capacity necessary for significant wind power quality improvement in a given period is found to be 20 to 40% of the energy produced in that period. The necessary power is found to be 80 to 100% of the average power of the period....

Long-term storage of spent nuclear fuel

International Nuclear Information System (INIS)

Kempe, T.F.; Martin, A.; Thorne, M.C.

1980-06-01

This report presents the results of a study on the storage of spent nuclear fuel, with particular reference to the options which would be available for long-term storage. Two reference programmes of nuclear power generation in the UK are defined and these are used as a basis for the projection of arisings of spent fuel and the storage capacity which might be needed. The characteristics of spent fuel which are relevant to long-term storage include the dimensions, materials and physical construction of the elements, their radioactive inventory and the associated decay heating as a function of time after removal from the reactor. Information on the behaviour of spent fuel in storage ponds is reviewed with particular reference to the corrosion of the cladding. The review indicates that, for long-term storage, both Magnox and AGR fuel would need to be packaged because of the high rate of cladding corrosion and the resulting radiological problems. The position on PWR fuel is less certain. Experience of dry storage is less extensive but it appears that the rate of corrosion of cladding is much lower than in water. Unit costs are discussed. Consideration is given to the radiological impact of fuel storage. (author)

Parametric Grid Information in the DOE Knowledge Base: Data Preparation, Storage, and Access

International Nuclear Information System (INIS)

Hipp, James R.; Moore, Susan G.; Myers, Stephen C.; Schultz, Craig A.; Shepherd, Ellen; Young, Christopher J.

1999-01-01

The parametric grid capability of the Knowledge Base provides an efficient, robust way to store and access interpolatable information which is needed to monitor the Comprehensive Nuclear Test Ban Treaty. To meet both the accuracy and performance requirements of operational monitoring systems, we use a new approach which combines the error estimation of kriging with the speed and robustness of Natural Neighbor Interpolation (NNI). The method involves three basic steps: data preparation (DP), data storage (DS), and data access (DA). The goal of data preparation is to process a set of raw data points to produce a sufficient basis for accurate NNI of value and error estimates in the Data Access step. This basis includes a set of nodes and their connectedness, collectively known as a tessellation, and the corresponding values and errors that map to each node, which we call surfaces. In many cases, the raw data point distribution is not sufficiently dense to guarantee accurate error estimates from the NNI, so the original data set must be densified using a newly developed interpolation technique known as Modified Bayesian Kriging. Once appropriate kriging parameters have been determined by variogram analysis, the optimum basis for NNI is determined in a process they call mesh refinement, which involves iterative kriging, new node insertion, and Delauny triangle smoothing. The process terminates when an NNI basis has been calculated which will fir the kriged values within a specified tolerance. In the data storage step, the tessellations and surfaces are stored in the Knowledge Base, currently in a binary flatfile format but perhaps in the future in a spatially-indexed database. Finally, in the data access step, a client application makes a request for an interpolated value, which triggers a data fetch from the Knowledge Base through the libKBI interface, a walking triangle search for the containing triangle, and finally the NNI interpolation

Storage of radioactive wastes

International Nuclear Information System (INIS)

1992-07-01

Even if the best waste minimization measures are undertaken throughout radioisotope production or usage, significant radioactive wastes arise to make management measures essential. For developing countries with low isotope usage and little or no generation of nuclear materials, it may be possible to handle the generated waste by simply practicing decay storage for several half-lives of the radionuclides involved, followed by discharge or disposal without further processing. For those countries with much larger facilities, longer lived isotopes are produced and used. In this situation, storage is used not only for decay storage but also for in-process retention steps and for the key stage of interim storage of conditioned wastes pending final disposal. The report will serve as a technical manual providing reference material and direct step-by-step know-how to staff in radioisotope user establishments and research centres in the developing Member States without nuclear power generation. Considerations are limited to the simpler storage facilities. The restricted quantities and low activity associated with the relevant wastes will generally permit contact-handling and avoid the need for shielding requirements in the storage facilities or equipment used for handling. A small quantity of wastes from some radioisotope production cells and from reactor cooling water treatment may contain sufficient short lived activity from activated corrosion products to require some separate decay storage before contact-handling is suitable. 16 refs, 12 figs, 8 tabs

Prior-Based Quantization Bin Matching for Cloud Storage of JPEG Images.

Science.gov (United States)

Liu, Xianming; Cheung, Gene; Lin, Chia-Wen; Zhao, Debin; Gao, Wen

2018-07-01

Millions of user-generated images are uploaded to social media sites like Facebook daily, which translate to a large storage cost. However, there exists an asymmetry in upload and download data: only a fraction of the uploaded images are subsequently retrieved for viewing. In this paper, we propose a cloud storage system that reduces the storage cost of all uploaded JPEG photos, at the expense of a controlled increase in computation mainly during download of requested image subset. Specifically, the system first selectively re-encodes code blocks of uploaded JPEG images using coarser quantization parameters for smaller storage sizes. Then during download, the system exploits known signal priors-sparsity prior and graph-signal smoothness prior-for reverse mapping to recover original fine quantization bin indices, with either deterministic guarantee (lossless mode) or statistical guarantee (near-lossless mode). For fast reverse mapping, we use small dictionaries and sparse graphs that are tailored for specific clusters of similar blocks, which are classified via tree-structured vector quantizer. During image upload, cluster indices identifying the appropriate dictionaries and graphs for the re-quantized blocks are encoded as side information using a differential distributed source coding scheme to facilitate reverse mapping during image download. Experimental results show that our system can reap significant storage savings (up to 12.05%) at roughly the same image PSNR (within 0.18 dB).

Influence of Storage on Briquettes Mechanical Properties

Directory of Open Access Journals (Sweden)

Brožek M.

2014-09-01

Full Text Available The effects of the storage place, placing manner, and storage time on mechanical properties of briquettes made from birch chips were laboratorily tested. A unique methodology developed by the present author enabling a relatively easy assessment of mechanical properties of the briquettes is described. The briquettes properties were evaluated by their density and rupture force determination. From the test results it follows that if the briquettes are stored in a well closed plastic bag, neither the place nor the storage time influence significantly their life time. When stored in a net plastic bag, the briquettes get seriously damaged, namely depending on their storage place and storage time.

Compact Holographic Data Storage

Science.gov (United States)

Chao, T. H.; Reyes, G. F.; Zhou, H.

2001-01-01

NASA's future missions would require massive high-speed onboard data storage capability to Space Science missions. For Space Science, such as the Europa Lander mission, the onboard data storage requirements would be focused on maximizing the spacecraft's ability to survive fault conditions (i.e., no loss in stored science data when spacecraft enters the 'safe mode') and autonomously recover from them during NASA's long-life and deep space missions. This would require the development of non-volatile memory. In order to survive in the stringent environment during space exploration missions, onboard memory requirements would also include: (1) survive a high radiation environment (1 Mrad), (2) operate effectively and efficiently for a very long time (10 years), and (3) sustain at least a billion write cycles. Therefore, memory technologies requirements of NASA's Earth Science and Space Science missions are large capacity, non-volatility, high-transfer rate, high radiation resistance, high storage density, and high power efficiency. JPL, under current sponsorship from NASA Space Science and Earth Science Programs, is developing a high-density, nonvolatile and rad-hard Compact Holographic Data Storage (CHDS) system to enable large-capacity, high-speed, low power consumption, and read/write of data in a space environment. The entire read/write operation will be controlled with electrooptic mechanism without any moving parts. This CHDS will consist of laser diodes, photorefractive crystal, spatial light modulator, photodetector array, and I/O electronic interface. In operation, pages of information would be recorded and retrieved with random access and high-speed. The nonvolatile, rad-hard characteristics of the holographic memory will provide a revolutionary memory technology meeting the high radiation challenge facing the Europa Lander mission. Additional information is contained in the original extended abstract.

Archival storage solutions for PACS

Science.gov (United States)

Chunn, Timothy

1997-05-01

While they are many, one of the inhibitors to the wide spread diffusion of PACS systems has been robust, cost effective digital archive storage solutions. Moreover, an automated Nearline solution is key to a central, sharable data repository, enabling many applications such as PACS, telemedicine and teleradiology, and information warehousing and data mining for research such as patient outcome analysis. Selecting the right solution depends on a number of factors: capacity requirements, write and retrieval performance requirements, scaleability in capacity and performance, configuration architecture and flexibility, subsystem availability and reliability, security requirements, system cost, achievable benefits and cost savings, investment protection, strategic fit and more.This paper addresses many of these issues. It compares and positions optical disk and magnetic tape technologies, which are the predominant archive mediums today. Price and performance comparisons will be made at different archive capacities, plus the effect of file size on storage system throughput will be analyzed. The concept of automated migration of images from high performance, high cost storage devices to high capacity, low cost storage devices will be introduced as a viable way to minimize overall storage costs for an archive. The concept of access density will also be introduced and applied to the selection of the most cost effective archive solution.

Continuous inventory in SNM storage facilities

International Nuclear Information System (INIS)

Chambers, W.H.

1975-01-01

Instrumentation and data processing techniques that provide inexpensive verification of material in storage were investigated. Transfers of special nuclear materials (SNM) into the storage area are accompanied by an automated verification of the container identity, weight, and the radiation signature of the contents. This information is computer-processed and stored for comparison at subsequent transfers and also provides the data base for record purposes. Physical movement of containers across the boundary of the storage area is presently accomplished by operating personnel in order to minimize expensive modifications to existing storage facilities. Personnel entering and leaving the storage area are uniquely identified and also through portal monitors capable of detecting small quantities of SNM. Once material is placed on the storage shelves, simple, low-cost container tagging and radiation sensors are activated. A portion of the prescribed gamma signature, obtained by duplicate shelf monitors during the transfer verification, is thus continuously checked against the stored identification data. Radiation detector design is severely constrained by the need to discriminate individual signatures in a high background area and the need for low unit costs. In operation any unauthorized change in signal is analyzed along with auxiliary data from surveillance sensors to activate the appropriate alarms. (auth))

The role of risk perception and technical information in scientific debates over nuclear waste storage

International Nuclear Information System (INIS)

Jenkins-Smith, Hank C.; Silva, Carol L.

1998-01-01

This article examines how members of the lay public factor risk perceptions, trust and technical information from differing scientific sources into policy judgements about potentially hazardous facilities. Focusing on radwaste storage repositories, we examine how members of the public filter new information about potential hazards through risk perceptions, and adjust their own beliefs about risks in light of that information. Scientists play a large (and increasing) role in public policy debates concerning nuclear waste issues, in which public perceptions of human health and environmental risks often differ substantially from scientific consensus about those risks. Public concerns and uncertainties are compounded when scientists from competing groups (government agencies, scientific institutions, industries, and interest groups) make different claims about the likely health and environmental consequences of different policy options. We show the processes by which the public receive and process scientific information about nuclear waste management risks using data taken from interviews with 1800 randomly selected individuals (1200 in New Mexico, and 600 nationwide). Among the more important findings are: (1) members of the public are able to make quite reasonable estimates about what kinds of positions on the risks of nuclear waste disposal will be taken by scientists from differing organizations (e.g. scientists from environmental groups, government agencies, or the nuclear industry); (2) in assessing the credibility of scientific claims, members of the public place great emphasis on the independence of the scientists from those who fund the research; and (3) prior expectations about the positions (or expected biases) of scientists from different organizations substantially affects the ways in which members of the public weigh (and utilize) information that comes from these scientists

The characteristics of electricity storage, renewables and markets

International Nuclear Information System (INIS)

Waterson, Michael

2017-01-01

This paper accepts the widespread view that as electricity generation systems transition towards a greater proportion of renewables provision, there will be an increasing need for storage facilities. However, it differs from most such studies in contrasting the private incentives of a storage operator with the public desirability of bulk storage. A key factor in the context of a market such as Britain, where renewable energy largely means wind generation, is the nature of wind generation itself. The problem of wind's high variance and intermittent nature is explored. It is argued that not only is there a missing money and a missing market issue in providing secure energy supplies, there is also a missing informational issue. A key opportunity for new storage is participation in a capacity market, if the setting is right. - Highlights: • Considers both the public and private incentives for developing energy storage. • Consideration of the intermittency of wind as a factor influencing storage. • Arbitrage analysed alongside other earning streams. • Impact of market design on extent of storage.

Neutrino Signals in Electron-Capture Storage-Ring Experiments

Directory of Open Access Journals (Sweden)

Avraham Gal

2016-06-01

Full Text Available Neutrino signals in electron-capture decays of hydrogen-like parent ions P in storage-ring experiments at GSI are reconsidered, with special emphasis placed on the storage-ring quasi-circular motion of the daughter ions D in two-body decays P → D + ν e . It is argued that, to the extent that daughter ions are detected, these detection rates might exhibit modulations with periods of order seconds, similar to those reported in the GSI storage-ring experiments for two-body decay rates. New dedicated experiments in storage rings, or using traps, could explore these modulations.

Gas storage materials, including hydrogen storage materials

Science.gov (United States)

Mohtadi, Rana F; Wicks, George G; Heung, Leung K; Nakamura, Kenji

2013-02-19

A material for the storage and release of gases comprises a plurality of hollow elements, each hollow element comprising a porous wall enclosing an interior cavity, the interior cavity including structures of a solid-state storage material. In particular examples, the storage material is a hydrogen storage material such as a solid state hydride. An improved method for forming such materials includes the solution diffusion of a storage material solution through a porous wall of a hollow element into an interior cavity.

Innovative Business Cases for Energy Storage In a Restructured Electricity Marketplace, A Study for the DOE Energy Storage Systems Program

Energy Technology Data Exchange (ETDEWEB)

IANNUCCI, JOE; EYER, JIM; BUTLER, PAUL C.

2003-02-01

This report describes the second phase of a project entitled ''Innovative Business Cases for Energy Storage in a Restructured Electricity Marketplace''. During part one of the effort, nine ''Stretch Scenarios'' were identified. They represented innovative and potentially significant uses of electric energy storage. Based on their potential to significantly impact the overall energy marketplace, the five most compelling scenarios were identified. From these scenarios, five specific ''Storage Market Opportunities'' (SMOs) were chosen for an in-depth evaluation in this phase. The authors conclude that some combination of the Power Cost Volatility and the T&D Benefits SMOs would be the most compelling for further investigation. Specifically, a combination of benefits (energy, capacity, power quality and reliability enhancement) achievable using energy storage systems for high value T&D applications, in regions with high power cost volatility, makes storage very competitive for about 24 GW and 120 GWh during the years of 2001 and 2010.

Opportunities for electricity storage in deregulating markets

International Nuclear Information System (INIS)

Graves, F.; Jenkin, T.; Murphy, D.

1999-01-01

This article addresses the value of electricity storage and its ability to take advantage of emerging energy arbitrage opportunities: buying power when it is inexpensive, and reselling it at a higher price. The focus of this article is on electricity markets and the opportunities they present for a merchant storage device, rather than on storage technologies themselves. There are a number of existing and emerging storage technologies: pumped hydro, various batteries, compressed air energy storage (CAES), superconducting magnetic energy storage (SMES), flywheels--even conventional hydro has storage-like properties. However, all these technologies operated on the same basic principle of exploiting short-term differentials in electricity prices: buy low, sell high (a strategy that is actually meaningful in electricity markets, unlike in financial markets). The object of this article is to develop and demonstrate a means for assessing the potential value of storage in different electricity markets, rather than to attempt to assess the prospects of a particular technology. The approach taken here is to look at price data from a number of actual electricity markets to determine what opportunities they might offer to a generic storage device. A storage technology is described here by its basic performance parameters--charge and generate capacity, energy inventory limits, and efficiency--which are sufficient to assess the basic economic potential of storage in a given market. The authors look primarily at US markets, but also compare and contrast findings with the situation in foreign markets in the U.K., Norway, Canada, and Australia, and discuss how market structure can influence the value of storage. Moreover, the authors use empirically observed relationships between hourly and 5 x 16 blocked prices to infer a rule for adjusting the value of storage assets in regions where only blocked price information is available

Nevada Nuclear Waste Storage Investigations, 1986--1987

International Nuclear Information System (INIS)

Tamura, A.T.; Lorenz, J.J.

1988-07-01

This bibliography contains information on the Nevada Nuclear Waste Storage Investigations (NNWSI) that was added to the DOE Energy Data Base from January 1986 through December 1987. It is a supplement to the first bibliography, Nevada Nuclear Waste Storage Investigations, 1977--1985 (DOE/TIC-3406), and includes all information in the preceding two updates, DOE/TIC-3406(Add.1) and DOE/TIC-3406(Add.2). The bibliography is categorized by principal NNWSI Project participant organizations. Participant-sponsored subcontractor reports, papers, and articles are included in the sponsoring organization's bibliography list and are listed in chronological order. The following indexes are provided: Corporate Author, Personal Author, Subject, Contract Number, Report Number, Order Number Correlation, and Key Word in Context

Natural language query system design for interactive information storage and retrieval systems. Presentation visuals. M.S. Thesis Final Report, 1 Jul. 1985 - 31 Dec. 1987

Science.gov (United States)

Dominick, Wayne D. (Editor); Liu, I-Hsiung

1985-01-01

This Working Paper Series entry represents a collection of presentation visuals associated with the companion report entitled Natural Language Query System Design for Interactive Information Storage and Retrieval Systems, USL/DBMS NASA/RECON Working Paper Series report number DBMS.NASA/RECON-17.

Information report on nuclear safety and radiation protection within the Aube low and medium activity radioactive waste storage Centre - 2011

International Nuclear Information System (INIS)

2012-06-01

After a presentation of the different installations of the Aube waste storage centre, this report describes the different measures regarding nuclear safety, radiation protection and security. It recalls and comments incidents and accidents which occurred within the installations in 2011. It describes the activities of control and survey of releases and of the environment. It describes the management of wastes produced by the centre itself. It indicates the various actions undertaken with respect to information and transparency

Energy Storage and Smart Energy Systems

DEFF Research Database (Denmark)

Lund, Henrik; Østergaard, Poul Alberg; Connolly, David

2016-01-01

It is often highlighted how the transition to renewable energy supply calls for significant electricity storage. However, one has to move beyond the electricity-only focus and take a holistic energy system view to identify optimal solutions for integrating renewable energy. In this paper......, an integrated cross-sector approach is used to determine the most efficient and least-cost storage options for the entire renewable energy system concluding that the best storage solutions cannot be found through analyses focusing on the individual sub-sectors. Electricity storage is not the optimum solution...... to integrate large inflows of fluctuating renewable energy, since more efficient and cheaper options can be found by integrating the electricity sector with other parts of the energy system and by this creating a Smart Energy System. Nevertheless, this does not imply that electricity storage should...

Modeling storage and demand management in power distribution grids

International Nuclear Information System (INIS)

Schroeder, Andreas

2011-01-01

Grahical abstract: The model informs an optimal investment sizing decision as regards specific 'smart grid' applications such as storage facilities and meters enabling load control. Results indicate that central storage facilities are a more promising option for generation cost reductions as compared to demand management. Highlights: → Stochastic versus deterministic model increases investment efficiency up to 5%. → Deterministic model under-estimates value of load control and storage. → Battery storage is beneficial at investment cost below 850 EUR/MW h. → Demand management equipment is not beneficial at cost beyond 200 EUR. → The stylized 10 kV grid constitutes no shortage factor. -- Abstract: Storage devices and demand control may constitute beneficial tools to optimize electricity generation with a large share of intermittent resources through inter-temporal substitution of load. This paper quantifies the related cost reductions in a simulation model of a simplified stylized medium-voltage grid (10 kV) under uncertain demand and wind output. Benders Decomposition Method is applied to create a two-stage stochastic optimization program. The model informs an optimal investment sizing decision as regards specific 'smart' applications such as storage facilities and meters enabling load control. Model results indicate that central storage facilities are a more promising option for generation cost reductions as compared to demand management. Grid extensions are not appropriate in any of the scenarios. A sensitivity analysis is applied with respect to the market penetration of uncoordinated Plug-In Electric Vehicles which are found to strongly encourage investment into load control equipment for 'smart' charging and slightly improve the case for central storage devices.

Solar heat storages in district heating networks

Energy Technology Data Exchange (ETDEWEB)

Ellehauge, K. (Ellehauge og Kildemoes, AArhus (DK)); Engberg Pedersen, T. (COWI A/S, Kgs. Lyngby (DK))

2007-07-15

This report gives information on the work carried out and the results obtained in Denmark on storages for large solar heating plants in district heating networks. Especially in Denmark the share of district heating has increased to a large percentage. In 1981 around 33% of all dwellings in DK were connected to a district heating network, while the percentage in 2006 was about 60% (in total 1.5 mio. dwellings). In the report storage types for short term storage and long term storages are described. Short term storages are done as steel tanks and is well established technology widely used in district heating networks. Long term storages are experimental and used in connection with solar heating. A number of solar heating plants have been established with either short term or long term storages showing economy competitive with normal energy sources. Since, in the majority of the Danish district heating networks the heat is produced in co-generation plants, i.e. plants producing both electricity and heat for the network, special attention has been put on the use of solar energy in combination with co-generation. Part of this report describes that in the liberalized electricity market central solar heating plants can also be advantageous in combination with co-generation plants. (au)

The neural bases of the short-term storage of verbal information are anatomically variable across individuals.

Science.gov (United States)

Feredoes, Eva; Tononi, Giulio; Postle, Bradley R

2007-10-10

What are the precise brain regions supporting the short-term retention of verbal information? A previous functional magnetic resonance imaging (fMRI) study suggested that they may be topographically variable across individuals, occurring, in most, in regions posterior to prefrontal cortex (PFC), and that detection of these regions may be best suited to a single-subject (SS) approach to fMRI analysis (Feredoes and Postle, 2007). In contrast, other studies using spatially normalized group-averaged (SNGA) analyses have localized storage-related activity to PFC. To evaluate the necessity of the regions identified by these two methods, we applied repetitive transcranial magnetic stimulation (rTMS) to SS- and SNGA-identified regions throughout the retention period of a delayed letter-recognition task. Results indicated that rTMS targeting SS analysis-identified regions of left perisylvian and sensorimotor cortex impaired performance, whereas rTMS targeting the SNGA-identified region of left caudal PFC had no effect on performance. Our results support the view that the short-term retention of verbal information can be supported by regions associated with acoustic, lexical, phonological, and speech-based representation of information. They also suggest that the brain bases of some cognitive functions may be better detected by SS than by SNGA approaches to fMRI data analysis.

Hydrogen Storage Technologies for Future Energy Systems.

Science.gov (United States)

Preuster, Patrick; Alekseev, Alexander; Wasserscheid, Peter

2017-06-07

Future energy systems will be determined by the increasing relevance of solar and wind energy. Crude oil and gas prices are expected to increase in the long run, and penalties for CO 2 emissions will become a relevant economic factor. Solar- and wind-powered electricity will become significantly cheaper, such that hydrogen produced from electrolysis will be competitively priced against hydrogen manufactured from natural gas. However, to handle the unsteadiness of system input from fluctuating energy sources, energy storage technologies that cover the full scale of power (in megawatts) and energy storage amounts (in megawatt hours) are required. Hydrogen, in particular, is a promising secondary energy vector for storing, transporting, and distributing large and very large amounts of energy at the gigawatt-hour and terawatt-hour scales. However, we also discuss energy storage at the 120-200-kWh scale, for example, for onboard hydrogen storage in fuel cell vehicles using compressed hydrogen storage. This article focuses on the characteristics and development potential of hydrogen storage technologies in light of such a changing energy system and its related challenges. Technological factors that influence the dynamics, flexibility, and operating costs of unsteady operation are therefore highlighted in particular. Moreover, the potential for using renewable hydrogen in the mobility sector, industrial production, and the heat market is discussed, as this potential may determine to a significant extent the future economic value of hydrogen storage technology as it applies to other industries. This evaluation elucidates known and well-established options for hydrogen storage and may guide the development and direction of newer, less developed technologies.

Design and installation manual for thermal energy storage

Energy Technology Data Exchange (ETDEWEB)

Cole, R L; Nield, K J; Rohde, R R; Wolosewicz, R M [eds.

1979-02-01

The purpose for this manual is to provide information on the design and installation of thermal energy storage in solar heating systems. It is intended for contractors, installers, solar system designers, engineers, architects, and manufacturers who intend to enter the solar energy business. The reader should have general knowledge of how solar heating systems operate and knowledge of construction methods and building codes. Knowledge of solar analysis methods such as f-chart, SOLCOST, DOE-1, or TRNSYS would be helpful. The information contained in the manual includes sizing storage, choosing a location for the storage device, and insulation requirements. Both air-based and liquid-based systems are covered with topics on designing rock beds, tank types, pump and fan selection, installation, costs, and operation and maintenance. Topics relevant to heating domestic water include safety, single- and dual-tank systems, domestic water heating with air- and liquid-based space heating system, and stand-alone domestic hot water systems. Several appendices present common problems with storage systems and their solutions, heat transfer fluid properties, heat exchanger sizing, and sample specifications for heat exchangers, wooden rock bins, steel tanks, concrete tanks, and fiberglass-reinforced plastic tanks.

Recovery of Flash Memories for Reliable Mobile Storages

Directory of Open Access Journals (Sweden)

Daesung Moon

2010-01-01

Full Text Available As the mobile appliance is applied to many ubiquitous services and the importance of the information stored in it is increased, the security issue to protect the information becomes one of the major concerns. However, most previous researches focused only on the communication security, not the storage security. Especially, a flash memory whose operational characteristics are different from those of HDD is used increasingly as a storage device for the mobile appliance because of its resistance to physical shock and lower power requirement. In this paper, we propose a flash memory management scheme targeted for guaranteeing the data integrity of the mobile storage. By maintaining the old data specified during the recovery window, we can recover the old data when the mobile appliance is attacked. Also, to reduce the storage requirement for the recovery, we restrict the number of versions to be copied, called Degree of Integrity (DoI. Especially, we consider both the reclaim efficiency and the wear leveling which is a unique characteristic of the flash memory. Based on the performance evaluation, we confirm that the proposed scheme can be acceptable to many applications as a flash memory management scheme for improving data integrity.

Operational Benefits of Meeting California's Energy Storage Targets

Energy Technology Data Exchange (ETDEWEB)

Eichman, Josh [National Renewable Energy Lab. (NREL), Golden, CO (United States); Denholm, Paul [National Renewable Energy Lab. (NREL), Golden, CO (United States); Jorgenson, Jennie [National Renewable Energy Lab. (NREL), Golden, CO (United States); Helman, Udi [Helman Analytics, San Francisco, CA (United States)

2015-12-18

In October 2013, the California Public Utilities Commission (CPUC) finalized procurement targets and other requirements to its jurisdictional utilities for a minimum of 1,325 MW of 'viable and cost-effective' energy storage systems by 2020. The goal of this study is to explore several aspects of grid operations in California and the Western Interconnection resulting from meeting the CPUC storage targets. We perform this analysis using a set of databases and grid simulation tools developed and implemented by the CPUC, the California Independent System Operator (CAISO), and the California Energy Commission (CEC) for the CPUC's Long-term Procurement Plan (LTPP). The 2014 version of this database contains information about generators, storage, transmission, and electrical demand, for California in the year 2024 for both 33% and 40% renewable energy portfolios. We examine the value of various services provided by energy storage in these scenarios. Sensitivities were performed relating to the services energy storage can provide, the capacity and duration of storage devices, export limitations, and negative price floor variations. Results show that a storage portfolio, as outlined by the CPUC, can reduce curtailment and system-wide production costs for 33% and 40% renewable scenarios. A storage device that can participate in energy and ancillary service markets provides the grid with the greatest benefit; the mandated storage requirement of 1,325 MW was estimated to reduce the total cost of production by about 78 million per year in the 33% scenario and 144 million per year in the 40% scenario. Much of this value is derived from the avoided start and stop costs of thermal generators and provision of ancillary services. A device on the 2024 California grid and participating in only ancillary service markets can provide the system with over 90% of the value as the energy and ancillary service device. The analysis points to the challenge of new storage

Improving communication for interdisciplinary teams working on storage of digital information in DNA.

Science.gov (United States)

Hesketh, Emily E; Sayir, Jossy; Goldman, Nick

2018-01-01

Close collaboration between specialists from diverse backgrounds and working in different scientific domains is an effective strategy to overcome challenges in areas that interface between biology, chemistry, physics and engineering. Communication in such collaborations can itself be challenging.  Even when projects are successfully concluded, resulting publications - necessarily multi-authored - have the potential to be disjointed. Few, both in the field and outside, may be able to fully understand the work as a whole. This needs to be addressed to facilitate efficient working, peer review, accessibility and impact to larger audiences. We are an interdisciplinary team working in a nascent scientific area, the repurposing of DNA as a storage medium for digital information. In this note, we highlight some of the difficulties that arise from such collaborations and outline our efforts to improve communication through a glossary and a controlled vocabulary and accessibility via short plain-language summaries. We hope to stimulate early discussion within this emerging field of how our community might improve the description and presentation of our work to facilitate clear communication within and between research groups and increase accessibility to those not familiar with our respective fields - be it molecular biology, computer science, information theory or others that might become relevant in future. To enable an open and inclusive discussion we have created a glossary and controlled vocabulary as a cloud-based shared document and we invite other scientists to critique our suggestions and contribute their own ideas.

Ten questions to Jean Dhers on the storage of electric energy

International Nuclear Information System (INIS)

2006-01-01

The authors proposes a comprehensive set of technical and economical data and information on electricity storage: the reasons to store energy (autonomous, stationary and network applications), the different types and advantages of energy storages with reversible power, the means to massively store electricity to exploit in on the network (description, uses and comparison of pumping energy transfer station, energy storage under the form of compressed air), the inertial storage (storage of kinetic energy accumulated in a flywheel, and its applications), the importance of storage with electrochemical batteries (reversible storage, evolution of batteries in ground transports, main economic sectors for batteries), fuel cells, the role of energy storage by power capacitors, the perspectives of super capacitors in a near future (comparison of their performance with those of batteries, possible applications), the use of electromagnetic storage of electricity (description, advantages, drawbacks and applications of superconducting magnet energy storage or SMES), and how the research on electric power storage is organised

Entangled Cloud Storage

DEFF Research Database (Denmark)

Ateniese, Giuseppe; Dagdelen, Özgür; Damgård, Ivan Bjerre

2012-01-01

keeps the files in it private but still lets each client P_i recover his own data by interacting with S; no cooperation from other clients is needed. At the same time, the cloud provider is discouraged from altering or overwriting any significant part of c as this will imply that none of the clients can......Entangled cloud storage enables a set of clients {P_i} to “entangle” their files {f_i} into a single clew c to be stored by a (potentially malicious) cloud provider S. The entanglement makes it impossible to modify or delete significant part of the clew without affecting all files in c. A clew...... recover their files. We provide theoretical foundations for entangled cloud storage, introducing the notion of an entangled encoding scheme that guarantees strong security requirements capturing the properties above. We also give a concrete construction based on privacy-preserving polynomial interpolation...

Proton storage ring summer workshop

International Nuclear Information System (INIS)

Lawrence, G.P.; Cooper, R.K.

1977-10-01

During the week of August 16, 1976 a Workshop was held at the Los Alamos Scientific Laboratory (LASL) on the Proton Storage Ring (PSR) for the Weapons Neutron Research Facility (WNRF). Written contributions were solicited from each of the participants in the Workshop, and the contributions that were received are presented. The papers do not represent polished or necessarily complete work, but rather represent ''first cuts'' at their respective areas. Topics covered include: (1) background information on the storage ring; (2) WNRF design; (3) rf transient during filling; (4) rf capture; (5) beam bunch compression; (6) transverse space charge limits; (7) transverse resistive instability in the PSR; (8) longitudinal resistive instability; (9) synchrotron frequency splitting; (10) E Quintus Unum--off resonance; (11) first harmonic bunching in the storage ring; (12) kicker considerations; (13) beam extraction; (14) ferrite kicker magnets; and (15) E Quintus Unum: a possible ejection scheme

PC-Cluster based Storage System Architecture for Cloud Storage

OpenAIRE

Yee, Tin Tin; Naing, Thinn Thu

2011-01-01

Design and architecture of cloud storage system plays a vital role in cloud computing infrastructure in order to improve the storage capacity as well as cost effectiveness. Usually cloud storage system provides users to efficient storage space with elasticity feature. One of the challenges of cloud storage system is difficult to balance the providing huge elastic capacity of storage and investment of expensive cost for it. In order to solve this issue in the cloud storage infrastructure, low ...

Status of Away From Reactor spent fuel storage program

International Nuclear Information System (INIS)

King, F.D.

1979-07-01

The Away From Reactor (AFR) Spent Fuel Program that the US Department of Energy established in 1977 is intended to preclude the shutting down of commercial nuclear power reactors because of lack of storage space for spent fuel. Legislation now being considered by Congress includes plans to provide storage space for commercial spent fuel beginning in 1983. Utilities are being encouraged to provide as much storage space as possible in their existing storage facilities, but projections indicate that a significant amount of AFR storage will be required. The government is evaluating the use of both existing and new storage facilities to solve this forecasted storage problem for commercial spent fuel

Entropy, pricing and productivity of pumped-storage

Science.gov (United States)

Karakatsanis, Georgios; Tyralis, Hristos; Tzouka, Katerina

2016-04-01

Pumped-storage constitutes today a mature method of bulk electricity storage in the form of hydropower. This bulk electricity storability upgrades the economic value of hydropower as it may mitigate -or even neutralize- stochastic effects deriving from various geophysical and socioeconomic factors, which produce numerous load balance inefficiencies due to increased uncertainty. Pumped-storage further holds a key role for unifying intermittent renewable (i.e. wind, solar) units with controllable non-renewable (i.e. nuclear, coal) fuel electricity generation plants into integrated energy systems. We develop a set of indicators for the measurement of performance of pumped-storage, in terms of the latter's energy and financial contribution to the energy system. More specifically, we use the concept of entropy in order to examine: (1) the statistical features -and correlations- of the energy system's intermittent components and (2) the statistical features of electricity demand prediction deviations. In this way, the macroeconomics of pumped-storage emerges naturally from its statistical features (Karakatsanis et al. 2014). In addition, these findings are combined to actual daily loads. Hence, not only the amount of energy harvested from the pumped-storage component is expected to be important, but the harvesting time as well, as the intraday price of electricity varies significantly. Additionally, the structure of the pumped-storage market proves to be a significant factor as well for the system's energy and financial performance (Paine et al. 2014). According to the above, we aim at postulating a set of general rules on the productivity of pumped-storage for (integrated) energy systems. Keywords: pumped-storage, storability, economic value of hydropower, stochastic effects, uncertainty, energy systems, entropy, intraday electricity price, productivity References 1. Karakatsanis, Georgios et al. (2014), Entropy, pricing and macroeconomics of pumped-storage systems

Evaluation of the Effect of Storage Temperature, Atmosphere and Packaging Materials on Some Properties of Carum copticum Fruits during Nine Months Storage

Directory of Open Access Journals (Sweden)

gonai baghdadi

2018-03-01

Full Text Available Introduction: The aim of medicinal plant storage is to preserve qualitative and quantitative properties of active substance. Carum copticum fruits (Zenyan in Persian were used for its therapeutic effects. Seed storage condition after harvest till to extraction time is not suitable in our country and the major part of seed quality deteriorates during the storage period. So, the loss of seed qualitative and quantitative characteristics will increase during unsuitable storage condition. Appropriate storage conditions and management preserve seed active substance, seed viability and vigor for long periods by reducing the rate of seed deterioration. Optimal seed storage can be achieved by modifying the environment around the seeds. Numerous storage systems have evolved over the years for post harvest preservation of crop seeds. The aim of this study is to evaluate the effect of various storage conditions and storage time on essential oil percentage and germination factors in C. copticum seeds during the storage period. The results of this research will be used for optimum storage of these seeds to better preserve their quality. Materials and Methods: In order to investigate the effects of storage conditions (packaging materials and temperature and storage time on quality of C. copticum stored seeds, a split-plot factorial arranged in a randomized complete block design with three replications is performed in Faculty of Agriculture at Ferdowsi University of Mashhad during 2013 and 2014.Tukey's range test was performed to determine the significant difference between treatments. The calculations were conducted by JMP 8 software. Temperature at two levels: 20±3°C and 30±3°C( as main plots and packaging materials (at six levels: paper, polyethylene, aluminum foil under vacuum condition, Polyethylene-polyamide packages under vacuum condition, Polyethylene-polyamide packages with a gas composition of [98%N2 + 2%O2] and [90%N2 +10%O2] and storage periods

A SHORT HISTORY CSISRS - AT THE CUTTING EDGE OF NUCLEAR DATA INFORMATION STORAGE AND RETRIEVAL SYSTEMS AND ITS RELATIONSHIP TO CINDA, EXFOR AND ENDF.

Energy Technology Data Exchange (ETDEWEB)

HOLDEN, N.E.

2005-12-01

A short history of CSISRS, pronounced ''scissors'' and standing for the Cross Section Information Storage and Retrieval System, is given. The relationship of CSISRS to CINDA, to the neutron nuclear data four-centers, to EXFOR and to ENDF, the evaluated neutron nuclear data file, is briefly explained.

Digital storage and analysis of color Doppler echocardiograms

Science.gov (United States)

Chandra, S.; Thomas, J. D.

1997-01-01

Color Doppler flow mapping has played an important role in clinical echocardiography. Most of the clinical work, however, has been primarily qualitative. Although qualitative information is very valuable, there is considerable quantitative information stored within the velocity map that has not been extensively exploited so far. Recently, many researchers have shown interest in using the encoded velocities to address the clinical problems such as quantification of valvular regurgitation, calculation of cardiac output, and characterization of ventricular filling. In this article, we review some basic physics and engineering aspects of color Doppler echocardiography, as well as drawbacks of trying to retrieve velocities from video tape data. Digital storage, which plays a critical role in performing quantitative analysis, is discussed in some detail with special attention to velocity encoding in DICOM 3.0 (medical image storage standard) and the use of digital compression. Lossy compression can considerably reduce file size with minimal loss of information (mostly redundant); this is critical for digital storage because of the enormous amount of data generated (a 10 minute study could require 18 Gigabytes of storage capacity). Lossy JPEG compression and its impact on quantitative analysis has been studied, showing that images compressed at 27:1 using the JPEG algorithm compares favorably with directly digitized video images, the current goldstandard. Some potential applications of these velocities in analyzing the proximal convergence zones, mitral inflow, and some areas of future development are also discussed in the article.

Integrated image storage solution for the Cath department.

Science.gov (United States)

Weterings, R A

1998-10-01

Contemporary Image Storage systems for the Catheterization department manage and distribute digital cardiac images according to the "cine-film" paradigm. The images are digital, but the applications have not changed much. This situation will change in the near future. New systems are being developed to store additional (clinical related) data with X-ray Angiographic (XA) Images. Furthermore, the image storage domains are no longer an island in the hospital infrastructure. Efficiency requires the availability of images with other data at the various "point of care" locations. This in turn raises requirements and expectations about the standards in the area of application interoperability, since no single vendor can supply the complete solution. Recent DICOM (Digital Imaging and Communications in Medicine) standardization activities play an important role in extending the current scope of image oriented storage solutions towards a more integrated imaging and information (clinical) folder for the Cath department. The paper will address the following issues: New requirements on "self-contained" Image Storage solutions for the Cath lab. How to deal with the demand for interdepartmental communication using upcoming (new) DICOM standards and HL7 (Health Level Seven) in this area. The increasing influence of computer technology, replacing vendor-specific solutions by general-accepted standards from the Information Technology (IT) world. A step-wise approach to come to an integrated clinical (patient) folder with inherent capabilities for data interchange with other Cardiology departments and the hospitals information infrastructure.

Assessment of plutonium storage safety issues at Department of Energy facilities

International Nuclear Information System (INIS)

1994-01-01

The Department of Energy (DOE) mission for utilization and storage of nuclear materials has recently changed as a result of the end of the ''Cold War'' era. Past and current plutonium storage practices largely reflect a temporary, in-process, or in-use storage condition which must now be changed to accommodate longer-term storage. This report summarizes information concerning current plutonium metal and oxide storage practices which was presented at the Office of Defense programs (DP) workshop in Albuquerque, New Mexico on May 26-27, 1993 and contained in responses to questions by DP-62 from the field organizations

Handling and storage of conditioned high-level wastes

International Nuclear Information System (INIS)

Heafield, W.

1984-01-01

This paper deals with certain aspects of the management of one of the most important radioactive wastes arising from the nuclear fuel cycle, i.e. the handling and storage of conditioned high-level wastes. The paper is based on an IAEA report of the same title published during 1983 in the Technical Reports Series. The paper provides illustrative background material on the characteristics of high-level wastes and, qualitatively, their requirements for conditioning. The principles important in the storage of high-level wastes are reviewed in conjunction with the radiological and socio-political considerations involved. Four fundamentally different storage concepts are described with reference to published information and the safety aspects of particular storage concepts are discussed. Finally, overall conclusions are presented which confirm the availability of technology for constructing and operating conditioned high-level waste storage facilities for periods of at least several decades. (author)

SOLID-STATE STORAGE DEVICE WITH PROGRAMMABLE PHYSICAL STORAGE ACCESS

DEFF Research Database (Denmark)

2017-01-01

a storage device action request, and the storage device evaluating a first rule of the one or more rules by determining if the received request fulfills request conditions comprised in the first rule, and in the affirmative the storage device performing request actions comprised in the first rule......Embodiments of the present invention includes a method of operating a solid-state storage device, comprising a storage device controller in the storage device receiving a set of one or more rules, each rule comprising (i) one or more request conditions to be evaluated for a storage device action...... request received from a host computer, and (ii) one or more request actions to be performed on a physical address space of a non-volatile storage unit in the solid-state storage device in case the one or more request conditions are fulfilled; the method further comprises: the storage device receiving...

Interim spent-fuel storage options at commercial nuclear power plants

International Nuclear Information System (INIS)

Thakkar, A.R.; Hylko, J.M.

1991-01-01

Although spent fuel can be stored safely in waterfilled pools at reactor sites, some utilities may not possess sufficient space for life-of-plant storage capability. In-pool storage capability may be increased by reracking assemblies, rod consolidation, double tiering spent-fuel racks, and by shipping spent fuel to other utility-owned facilities. Long-term on-site storage capability for spent fuel may be provided by installing (dry-type) metal casks, storage and transportation casks, concrete casks, horizontal concrete modules, modular concrete vaults, or by constructing additional (pool-type) storage installations. Experience to date has provided valuable information regarding dry-type or pool-type installations, cask handling and staffing requirements, security features, decommissioning activities, and radiological issues

Extended storage of low-level radioactive waste: potential problem areas

International Nuclear Information System (INIS)

Siskind, B.; Dougherty, D.R.; MacKenzie, D.R.

1985-01-01

If a state or state compact does not have adequate disposal capacity for low-level radioactive waste (LLRW) by 1986 as required by the Low-Level Waste Policy Act, then extended storage of certain LLRW may be necessary. The issue of extended storage of LLRW is addressed in order to determine for the Nuclear Regulatory Commission the areas of concern and the actions recommended to resolve these concerns. The focus is on the properties and behavior of the waste form and waste container. Storage alternatives are considered in order to characterize the likely storage environments for these wastes. The areas of concern about extended storage of LLRW are grouped into two categories: 1. Behavior of the waste form and/or container during storage, e.g., radiolytic gas generation, radiation-enhanced degradation of polymeric materials, and corrosion. 2. Effects of extended storage on the properties of the waste form and/or container that are important after storage (e.g., radiation-induced oxidative embrittlement of high-density polyethylene and the weakening of steel containers resulting from corrosion by the waste). The additional information and actions required to address these concerns are discussed and, in particular, it is concluded that further information is needed on the rates of corrosion of container material by Class A wastes and on the apparent dose-rate dependence of radiolytic processes in Class B and C waste packages. Modifications to the guidance for solidified wastes and high-integrity containers in NRC's Technical Position on Waste Form are recommended. 27 references

The Integrated Information System for Natural Disaster Mitigation

Directory of Open Access Journals (Sweden)

Junxiu Wu

2007-08-01

Full Text Available Supported by the World Bank, the Integrated Information System for Natural Disaster Mitigation (ISNDM, including the operational service system and network telecommunication system, has been in development for three years in the Center of Disaster Reduction, Chinese Academy of Sciences, based on the platform of the GIS software Arcview. It has five main modules: disaster background information, socio- economic information, disaster-induced factors database, disaster scenarios database, and disaster assessment. ISNDM has several significant functions, which include information collection, information processing, data storage, and information distribution. It is a simple but comprehensive demonstration system for our national center for natural disaster reduction.

Developing new transportable storage casks for interim dry storage

International Nuclear Information System (INIS)

Hayashi, K.; Iwasa, K.; Araki, K.; Asano, R.

2004-01-01

Transportable storage metal casks are to be consistently used during transport and storage for AFR interim dry storage facilities planning in Japan. The casks are required to comply with the technical standards of regulations for both transport (hereinafter called ''transport regulation'') and storage (hereafter called ''storage regulation'') to maintain safety functions (heat transfer, containment, shielding and sub-critical control). In addition to these requirements, it is not planned in normal state to change the seal materials during storage at the storage facility, therefore it is requested to use same seal materials when the casks are transported after storage period. The dry transportable storage metal casks that satisfy the requirements have been developed to meet the needs of the dry storage facilities. The basic policy of this development is to utilize proven technology achieved from our design and fabrication experience, to carry out necessary verification for new designs and to realize a safe and rational design with higher capacity and efficient fabrication

SOFTWARE AND TECHNOLOGY FOR COLLECTING AND STORAGE SERIAL OBSERVATIONS OF THE ENVIRONMENT

Directory of Open Access Journals (Sweden)

A. V. Tokarev

2014-01-01

Full Text Available Some aspects of the collecting and storage serial observations of the environment is considered. The paper considers the creation of a storage subsystem and climate data collection, which will enable users to perform data collection, integration, storage and analysis. Developed server data collector prototype implement basic functions of the program interface (API and administrative webinterface. Several data flows from different data sources is created – public sources of climate data, autonomous weather stations, information systems of monitoring. Work is underway to establish a means for effective access to observational data, services, reporting and analysis of information.

Carbon capture and storage: Fundamental thermodynamics and current technology

International Nuclear Information System (INIS)

Page, S.C.; Williamson, A.G.; Mason, I.G.

2009-01-01

Carbon capture and storage (CCS) is considered a leading technology for reducing CO 2 emissions from fossil-fuelled electricity generation plants and could permit the continued use of coal and gas whilst meeting greenhouse gas targets. However considerable energy is required for the capture, compression, transport and storage steps involved. In this paper, energy penalty information in the literature is reviewed, and thermodynamically ideal and 'real world' energy penalty values are calculated. For a sub-critical pulverized coal (PC) plant, the energy penalty values for 100% capture are 48.6% and 43.5% for liquefied CO 2 , and for CO 2 compressed to 11 MPa, respectively. When assumptions for supercritical plants were incorporated, results were in broad agreement with published values arising from process modelling. However, we show that energy use in existing capture operations is considerably greater than indicated by most projections. Full CCS demonstration plants are now required to verify modelled energy penalty values. However, it appears unlikely that CCS will deliver significant CO 2 reductions in a timely fashion. In addition, many uncertainties remain over the permanence of CO 2 storage, either in geological formations, or beneath the ocean. We conclude that further investment in CCS should be seriously questioned by policy makers.

The Impact of Changing Storage Area on Flood Magnitude and Occurrence

Directory of Open Access Journals (Sweden)

Kusumastuti D.I.

2012-01-01

Full Text Available This study focuses on the impact of combined catchment and storage upon flood occurrences and flood peaks. A significant factor that plays an important role of the combined catchment and storage is the ratio of contributing catchment area to storage area (AC/AS where the impact significantly shows increasing frequency of storage overflow and flood peaks with the increasing of AC/AS. Some case studies examined in this work, i.e. Way Pegadungan (Lampung, Sumatra and NagaraRiver (South Kalimantan catchments show similar behavior. Swamps located on the sides of downstream of Way Pegadungan as well as Nagara River act as storages during flood events. The dyke which was planned to be built increases the ratio of AC/AS significantly as storage area reduced considerably. This has an impact on flood peaks which can increase considerably. The improved understanding of these process controls will be useful in assisting the management of such catchments, particularly to assist in flood prevention and mitigation.

Long vs. short-term energy storage:sensitivity analysis.

Energy Technology Data Exchange (ETDEWEB)

Schoenung, Susan M. (Longitude 122 West, Inc., Menlo Park, CA); Hassenzahl, William V. (,Advanced Energy Analysis, Piedmont, CA)

2007-07-01

This report extends earlier work to characterize long-duration and short-duration energy storage technologies, primarily on the basis of life-cycle cost, and to investigate sensitivities to various input assumptions. Another technology--asymmetric lead-carbon capacitors--has also been added. Energy storage technologies are examined for three application categories--bulk energy storage, distributed generation, and power quality--with significant variations in discharge time and storage capacity. Sensitivity analyses include cost of electricity and natural gas, and system life, which impacts replacement costs and capital carrying charges. Results are presented in terms of annual cost, $/kW-yr. A major variable affecting system cost is hours of storage available for discharge.

Monitoring of injected CO2 at two commercial geologic storage sites with significant pressure depletion and/or re-pressurization histories: A case study

Directory of Open Access Journals (Sweden)

Dayanand Saini

2017-03-01

The monitoring technologies that have been used/deployed/tested at both the normally pressured West Hastings and the subnormally pressured Bell Creek storage sites appear to adequately address any of the potential “out of zone migration” of injected CO2 at these sites. It would be interesting to see if any of the collected monitoring data at the West Hastings and the Bell Creek storage sites could also be used in future to better understand the viability of initially subnormally pressured and subsequently depleted and re-pressurized oil fields as secure geologic CO2 storage sites with relatively large storage CO2 capacities compared to the depleted and re-pressurized oil fields that were initially discovered as normally pressured.

Information on the feasibility study for the reracking in the fuel storage pools of the Juragua Nuclear Power Plant

International Nuclear Information System (INIS)

Rodriguez, J.M.; Rodriguez, I.; Lopez, D.; Guerra, R.; Rodriguez, M.; Garcia, F.

1995-01-01

During 1993, in the Juragua Nuclear Power Plants as engineering evaluation programme was initiated in the storage area of irradiated nuclear fuel, where work in order to determine the feasibility of capacity increase for storage of irradiated nuclear fuel at the fuel storage pools using poisoned compact close racks instead of the originally designed racks. The feasibility study is a fundamental activity of this programme for the 1994-1995 period. According to this study the prospects of assimilation of compact storage conditions in the fuel storage pools in unit number one and prolonged fuel storage pool are investigated

EMI StAR – Definition of a Storage Accounting Record

CERN Document Server

Nilsen, J.K.; Müller-Pfefferkorn, R.; Molnar, Z.; Zappi, R.

2011-01-01

In this document the EU-project European Middleware Initiative (EMI) describes a storage accounting record (StAR), defined to reflect practical, financial and legal requirements of storage location, usage and space and data flow. The defined record might be the base for a standardized schema or an extension of an existing record like the OGF UR and this document is intended as information to be taken as input for incorporating storage resources into the OGF UR.

The Effects of Storage on Germination Characteristics and Enzyme Activity of Sorghum Seeds

Directory of Open Access Journals (Sweden)

Azadi M.S.

2013-11-01

Full Text Available Seed moisture content (MC and storage temperature are the most important factors affecting seed longevity and vigor. Exposure to warm, moist air is principally responsible for this. Proper storage and optimum seed moisture content can affect the grain quality significantly. The purpose of this study was to evaluate the different storage treatments on seed quality of sorghum. The seed materials were fresh without any storage period. For storage treatments, 3 seed moisture contents (6, 10, 14 % were stored for 8 month in 0.5 L capacity sealed aluminum foil packet in 0.3 bar inside incubators set at 4 temperatures (5, 15, 25, 35 °C. After storage time, the higher the storage temperature, the lower was the grain quality of sorghum. The highest germination percentage, germination index, normal seedling percentage were achieved in control conditions (0 day of storage. Our results showed that increasing storage duration resulted higher reduction in germination characteristics. Also our results showed that, germination percentage, means time to germination, germination index, normal seedling percentage decrease significantly by storage. Enzyme activity decrease significantly by increased in storage.

Waste management and the land disposal restriction storage prohibition

International Nuclear Information System (INIS)

1992-05-01

RCRA Sect. 3004(j) prohibits storage of wastes that have been prohibited from land disposal, unless that storage is for the purpose of accumulating sufficient quantities of hazardous wastes to facilitate proper recovery, treatment, or disposal. This requirement was incorporated as part of the Land Disposal Restriction (LDR) regulations. Under the LDR storage prohibition, facilities may only store restricted wastes in containers and tanks. As stated in the Third LDR rule, storage of prohibited waste is only allowed in non-land based storage units since land-based storage is a form of disposal. The EPA has recognized that generators and storers of radioactive mixed waste (RMW) may find it impossible to comply with storage prohibition in cases where no available treatment capacity exists. Additionally, under the current regulatory interpretation, there is no provision that would allow for storage of wastes for which treatment capacity and capability are not available, even where capacity is legitimately being developed. Under the LDR program, restricted wastes that are disposed of, or placed into storage before an LDR effective date, are not subject to the LDR requirements. However, if such wastes are removed from a storage or disposal site after the effective date, such wastes would be subject to LDR requirements. The purpose of this information brief is to clarify what waste management practices constitute removal from storage

Spent fuel storage requirements. An update of DOE/RL-83-1

International Nuclear Information System (INIS)

1984-05-01

Spent fuel storage capacities at some commercial light water reactors (LWRs) are inadequate to handle projected spent fuel discharges. This report presents estimates of potential near-term requirements for additional LWR spent fuel storage capacity, based on information voluntarily supplied by utilities operating commercial nuclear power plants. These estimates provide information needed for planning the Department of Energy's (DOE) Federal Interim Storage (FIS) Program and the spent fuel research, development, and demonstration (RD and D) activities to be carried out under the DOE's Commercial Spent Fuel Management (CSFM) Program, in conjunction with the requirements of the Nuclear Waste Policy Act of 1982. This report is the latest in a series published by the DOE on LWR spent fuel storage requirements. Since the planning needs of the CSFM program focus on the near-term management of spent fuel inventories from commercial nuclear power reactors, the estimates in this report cover the ten-year period from the present through 1983. The report also assesses the possible impacts of using various concepts to reduce the requirements for additional storage capacity

The effects of frozen tissue storage conditions on the integrity of RNA and protein.

Science.gov (United States)

Auer, H; Mobley, J A; Ayers, L W; Bowen, J; Chuaqui, R F; Johnson, L A; Livolsi, V A; Lubensky, I A; McGarvey, D; Monovich, L C; Moskaluk, C A; Rumpel, C A; Sexton, K C; Washington, M K; Wiles, K R; Grizzle, W E; Ramirez, N C

2014-10-01

Unfixed tissue specimens most frequently are stored for long term research uses at either -80° C or in vapor phase liquid nitrogen (VPLN). There is little information concerning the effects such long term storage on tissue RNA or protein available for extraction. Aliquots of 49 specimens were stored for 5-12 years at -80° C or in VPLN. Twelve additional paired specimens were stored for 1 year under identical conditions. RNA was isolated from all tissues and assessed for RNA yield, total RNA integrity and mRNA integrity. Protein stability was analyzed by surface-enhanced or matrix-assisted laser desorption ionization time of flight mass spectrometry (SELDI-TOF-MS, MALDI-TOF-MS) and nano-liquid chromatography electrospray ionization tandem mass spectrometry (nLC-ESI-MS/MS). RNA yield and total RNA integrity showed significantly better results for -80° C storage compared to VPLN storage; the transcripts that were preferentially degraded during VPLN storage were these involved in antigen presentation and processing. No consistent differences were found in the SELDI-TOF-MS, MALDI-TOF-MS or nLC-ESI-MS/MS analyses of specimens stored for more than 8 years at -80° C compared to those stored in VPLN. Long term storage of human research tissues at -80° C provides at least the same quality of RNA and protein as storage in VPLN.

Developing new transportable storage casks for interim dry storage

Energy Technology Data Exchange (ETDEWEB)

Hayashi, K.; Iwasa, K.; Araki, K.; Asano, R. [Hitachi Zosen Diesel and Engineering Co., Ltd., Tokyo (Japan)

2004-07-01

Transportable storage metal casks are to be consistently used during transport and storage for AFR interim dry storage facilities planning in Japan. The casks are required to comply with the technical standards of regulations for both transport (hereinafter called ''transport regulation'') and storage (hereafter called ''storage regulation'') to maintain safety functions (heat transfer, containment, shielding and sub-critical control). In addition to these requirements, it is not planned in normal state to change the seal materials during storage at the storage facility, therefore it is requested to use same seal materials when the casks are transported after storage period. The dry transportable storage metal casks that satisfy the requirements have been developed to meet the needs of the dry storage facilities. The basic policy of this development is to utilize proven technology achieved from our design and fabrication experience, to carry out necessary verification for new designs and to realize a safe and rational design with higher capacity and efficient fabrication.

Information retrieval system: impacts of water-level changes on uses of federal storage reservoirs of the Columbia River.

Energy Technology Data Exchange (ETDEWEB)

Fickeisen, D.H.; Cowley, P.J.; Neitzel, D.A.; Simmons, M.A.

1982-09-01

A project undertaken to provide the Bonneville Power Administration (BPA) with information needed to conduct environmental assessments and meet requirements of the National Environmental Policy Act (NEPA) and the Pacific Northwest Electric Power Planning and Conservation Act (Regional Act) is described. Access to information on environmental effects would help BPA fulfill its responsibilities to coordinate power generation on the Columbia River system, protect uses of the river system (e.g., irrigation, recreation, navigation), and enhance fish and wildlife production. Staff members at BPA identified the need to compile and index information resources that would help answer environmental impact questions. A computer retrieval system that would provide ready access to the information was envisioned. This project was supported by BPA to provide an initial step toward a compilation of environmental impact information. Scientists at Pacific Northwest Laboratory (PNL) identified, gathered, and evaluated information related to environmental effects of water level on uses of five study reservoirs and developed and implemented and environmental data retrieval system, which provides for automated storage and retrieval of annotated citations to published and unpublished information. The data retrieval system is operating on BPA's computer facility and includes the reservoir water-level environmental data. This project was divided into several tasks, some of which were conducted simultaneously to meet project deadlines. The tasks were to identify uses of the five study reservoirs, compile and evaluate reservoir information, develop a data entry and retrieval system, identify and analyze research needs, and document the data retrieval system and train users. Additional details of the project are described in several appendixes.

The Safety Assessment of Long term Interim Storage at Sellafield

International Nuclear Information System (INIS)

Buchan, Andrew B.

2014-01-01

The Sellafield site comprises a wide range of nuclear facilities, including operating facilities associated with the Magnox reprocessing programme, the Thermal Oxide Reprocessing Plant (THORP) and a range of waste treatment plants. The operational life of some of the site facilities currently extends to 2120, requiring the retrieval, treatment, consolidation and safe extended storage of a variety of radioactive materials. Sellafield has utilised its existing safety assessment processes to inform and prioritise studies into beyond design basis events and resilience evaluation required following Fukushima by UK regulators and industry bodies such as WANO. There are significant differences between NPPs, for which the ENSREG 'stress tests' were originally intended, and the Sellafield site which is instead centered around two reprocessing facilities (Magnox and THORP), with a supporting infrastructure of waste processing and storage facilities, coupled with a legacy of high hazard older facilities. In the former case the consequences of a catastrophic failure are promptly realised, leading to significant problems such as fuel failure / meltdown in AGRs and LWRs respectively in the event of complete loss of cooling. At Sellafield, the processes are carried out at comparatively low temperatures and pressures with relatively low rates of change following any loss of cooling. Instead the consequences of catastrophic failure at Sellafield are more directly related to the very large inventories of radioactive materials, including high level liquid wastes and unprocessed fuels, present in specific plants and to the condition of the ageing assets, holding legacy wastes. The paper will consider how a number of analysis techniques have been used to establish a safety case for fault and accident conditions, i.e. design basis analysis (DBA), probabilistic safety analysis (PSA) and severe accident analysis (SAA) DBA is focused on the key safety measures for those initiating faults

Methane storage in metal-organic frameworks.

Science.gov (United States)

He, Yabing; Zhou, Wei; Qian, Guodong; Chen, Banglin

2014-08-21

Natural gas (NG), whose main component is methane, is an attractive fuel for vehicular applications. Realization of safe, cheap and convenient means and materials for high-capacity methane storage can significantly facilitate the implementation of natural gas fuelled vehicles. The physisorption based process involving porous materials offers an efficient storage methodology and the emerging porous metal-organic frameworks have been explored as potential candidates because of their extraordinarily high porosities, tunable pore/cage sizes and easily immobilized functional sites. In this view, we provide an overview of the current status of metal-organic frameworks for methane storage.

AB Levitator and Electricity Storage

OpenAIRE

Bolonkin, Alexander

2007-01-01

The author researched this new idea - support of flight by any aerial vehicles at significant altitude solely by the magnetic field of the planet. It is shown that current technology allows humans to create a light propulsion (AB engine) which does not depend on air, water or ground terrain. Simultaniosly, this revolutionary thruster is a device for the storage of electricity which is extracted and is replenished (during braking) from/into the storage with 100 percent efficiency. The relative...

Energy Storage and Smart Energy Systems

Directory of Open Access Journals (Sweden)

Poul Alberg Østergaard

2016-12-01

Full Text Available It is often highlighted how the transition to renewable energy supply calls for significant electricity storage. However, one has to move beyond the electricity-only focus and take a holistic energy system view to identify optimal solutions for integrating renewable energy. In this paper, an integrated cross-sector approach is used to determine the most efficient and least-cost storage options for the entire renewable energy system concluding that the best storage solutions cannot be found through analyses focusing on the individual sub-sectors. Electricity storage is not the optimum solution to integrate large inflows of fluctuating renewable energy, since more efficient and cheaper options can be found by integrating the electricity sector with other parts of the energy system and by this creating a Smart Energy System. Nevertheless, this does not imply that electricity storage should be disregarded but that it will be needed for other purposes in the future.

DICOM implementation on online tape library storage system

Science.gov (United States)

Komo, Darmadi; Dai, Hailei L.; Elghammer, David; Levine, Betty A.; Mun, Seong K.

1998-07-01

The main purpose of this project is to implement a Digital Image and Communications (DICOM) compliant online tape library system over the Internet. Once finished, the system will be used to store medical exams generated from U.S. ARMY Mobile ARMY Surgical Hospital (MASH) in Tuzla, Bosnia. A modified UC Davis implementation of DICOM storage class is used for this project. DICOM storage class user and provider are implemented as the system's interface to the Internet. The DICOM software provides flexible configuration options such as types of modalities and trusted remote DICOM hosts. Metadata is extracted from each exam and indexed in a relational database for query and retrieve purposes. The medical images are stored inside the Wolfcreek-9360 tape library system from StorageTek Corporation. The tape library system has nearline access to more than 1000 tapes. Each tape has a capacity of 800 megabytes making the total nearline tape access of around 1 terabyte. The tape library uses the Application Storage Manager (ASM) which provides cost-effective file management, storage, archival, and retrieval services. ASM automatically and transparently copies files from expensive magnetic disk to less expensive nearline tape library, and restores the files back when they are needed. The ASM also provides a crash recovery tool, which enable an entire file system restore in a short time. A graphical user interface (GUI) function is used to view the contents of the storage systems. This GUI also allows user to retrieve the stored exams and send the exams to anywhere on the Internet using DICOM protocols. With the integration of different components of the system, we have implemented a high capacity online tape library storage system that is flexible and easy to use. Using tape as an alternative storage media as opposed to the magnetic disk has the great potential of cost savings in terms of dollars per megabyte of storage. As this system matures, the Hospital Information Systems

Bulk energy storage increases United States electricity system emissions.

Science.gov (United States)

Hittinger, Eric S; Azevedo, Inês M L

2015-03-03

Bulk energy storage is generally considered an important contributor for the transition toward a more flexible and sustainable electricity system. Although economically valuable, storage is not fundamentally a "green" technology, leading to reductions in emissions. We model the economic and emissions effects of bulk energy storage providing an energy arbitrage service. We calculate the profits under two scenarios (perfect and imperfect information about future electricity prices), and estimate the effect of bulk storage on net emissions of CO2, SO2, and NOx for 20 eGRID subregions in the United States. We find that net system CO2 emissions resulting from storage operation are nontrivial when compared to the emissions from electricity generation, ranging from 104 to 407 kg/MWh of delivered energy depending on location, storage operation mode, and assumptions regarding carbon intensity. Net NOx emissions range from -0.16 (i.e., producing net savings) to 0.49 kg/MWh, and are generally small when compared to average generation-related emissions. Net SO2 emissions from storage operation range from -0.01 to 1.7 kg/MWh, depending on location and storage operation mode.

Strategies for commercializing customer thermal-energy storage. [64 references

Energy Technology Data Exchange (ETDEWEB)

Nelson, S.H.

1976-12-01

This report presents strategies for commercializing customer thermal storage. Four storage techniques are evaluated: space heating, air conditioning, hot-water heating, and interruptible hot-water heating. The storage systems involved store off-peak electric energy for thermal applications during peak load hours. Analyses of both storage techniques and principal parties affected by storage indicate four barriers: the absence of (1) commercially available air conditioning storage devices, (2) appropriate rates, (3) information on both rates and devices, and (4) widespread utility support. Development of appropriate rates is the key to commercialization. The criteria used to evaluate rate types are: maximum combined utility and customer benefits, ease of commercialization, and practical feasibility. Four rate types--demand charges, time-of-use rates, and two forms of load management rates (a monthly credit and an off-peak discount)--plus the possibility of utility ownership are considered. The best rate types for each storage option are: for hot-water heating, a monthly credit for allowing utility interruptions or an off-peak price discount for storage; for space heating, an off-peak discount contingent upon meeting utility requirements; and for air conditioning, an off-peak discount plus monthly credit.

Pad B Liquid Hydrogen Storage Tank

Science.gov (United States)

Hall, Felicia

2007-01-01

Kennedy Space Center is home to two liquid hydrogen storage tanks, one at each launch pad of Launch Complex 39. The liquid hydrogen storage tank at Launch Pad B has a significantly higher boil off rate that the liquid hydrogen storage tank at Launch Pad A. This research looks at various calculations concerning the at Launch Pad B in an attempt to develop a solution to the excess boil off rate. We will look at Perlite levels inside the tank, Boil off rates, conductive heat transfer, and radiant heat transfer through the tank. As a conclusion to the research, we will model the effects of placing an external insulation to the tank in order to reduce the boil off rate and increase the economic efficiency of the liquid hydrogen storage tanks.

Energy storage

Science.gov (United States)

Kaier, U.

1981-04-01

Developments in the area of energy storage are characterized, with respect to theory and laboratory, by an emergence of novel concepts and technologies for storing electric energy and heat. However, there are no new commercial devices on the market. New storage batteries as basis for a wider introduction of electric cars, and latent heat storage devices, as an aid for solar technology applications, with satisfactory performance standards are not yet commercially available. Devices for the intermediate storage of electric energy for solar electric-energy systems, and for satisfying peak-load current demands in the case of public utility companies are considered. In spite of many promising novel developments, there is yet no practical alternative to the lead-acid storage battery. Attention is given to central heat storage for systems transporting heat energy, small-scale heat storage installations, and large-scale technical energy-storage systems.

Industrial center of gathering, warehousing and storage. Annual report 2015

International Nuclear Information System (INIS)

2016-01-01

This report first presents the installations of the Cires (industrial center for regrouping, warehousing and storage), its equipment and buildings, its activities (storage of very-low-activity wastes, regrouping and warehousing of non-electronuclear wastes). It reviews the arrangements regarding safety and radiation protection: radioactive waste storage safety, safety of non-electronuclear waste regrouping and warehousing, relationship with the regional directorate of environment, planning and housing (DREAL), quality audits, staff safety, and radiation protection. It addresses the actions undertaken for the monitoring of the environment and of releases by the installations: radiological control in various locations (measurements in soils, waters, underground waters, and atmospheric releases), physical and chemical controls. The next part reports actions regarding transparency and information (visits, conferences, exhibitions, relationship with the local information and control commission)

Industrial center of gathering, warehousing and storage. Annual report 2016

International Nuclear Information System (INIS)

2016-01-01

This report first presents the installations of the Cires (industrial center for regrouping, warehousing and storage), its equipment and buildings, its activities (storage of very-low-activity wastes, regrouping and warehousing of non-electronuclear wastes). It reviews the arrangements regarding safety and radiation protection: radioactive waste storage safety, safety of non-electronuclear waste regrouping and warehousing, relationship with the regional directorate of environment, planning and housing (DREAL), quality audits, staff safety, and radiation protection. It addresses the actions undertaken for the monitoring of the environment and of releases by the installations: radiological control in various locations (measurements in soils, waters, underground waters, and atmospheric releases), physical and chemical controls. The next part reports actions regarding transparency and information (visits, conferences, exhibitions, relationship with the local information and control commission)

Prospects for hydrogen storage in graphene.

Science.gov (United States)

Tozzini, Valentina; Pellegrini, Vittorio

2013-01-07

Hydrogen-based fuel cells are promising solutions for the efficient and clean delivery of electricity. Since hydrogen is an energy carrier, a key step for the development of a reliable hydrogen-based technology requires solving the issue of storage and transport of hydrogen. Several proposals based on the design of advanced materials such as metal hydrides and carbon structures have been made to overcome the limitations of the conventional solution of compressing or liquefying hydrogen in tanks. Nevertheless none of these systems are currently offering the required performances in terms of hydrogen storage capacity and control of adsorption/desorption processes. Therefore the problem of hydrogen storage remains so far unsolved and it continues to represent a significant bottleneck to the advancement and proliferation of fuel cell and hydrogen technologies. Recently, however, several studies on graphene, the one-atom-thick membrane of carbon atoms packed in a honeycomb lattice, have highlighted the potentialities of this material for hydrogen storage and raise new hopes for the development of an efficient solid-state hydrogen storage device. Here we review on-going efforts and studies on functionalized and nanostructured graphene for hydrogen storage and suggest possible developments for efficient storage/release of hydrogen under ambient conditions.

Storage of RF photons in minimal conditions

Science.gov (United States)

Cromières, J.-P.; Chanelière, T.

2018-02-01

We investigate the minimal conditions to store coherently a RF pulse in a material medium. We choose a commercial quartz as a memory support because it is a widely available component with a high Q-factor. Pulse storage is obtained by varying dynamically the light-matter coupling with an analog switch. This parametric driving of the quartz dynamics can be alternatively interpreted as a stopped-light experiment. We obtain an efficiency of 26%, a storage time of 209 μs and a time-to-bandwidth product of 98 by optimizing the pulse temporal shape. The coherent character of the storage is demonstrated. Our goal is to connect different types of memories in the RF and optical domain for quantum information processing. Our motivation is essentially fundamental.

Deriving Area-storage Curves of Global Reservoirs

Science.gov (United States)

Mu, M.; Tang, Q.

2017-12-01

Basic information including capacity, dam height, and largest water area on global reservoirs and dams is well documented in databases such as GRanD (Global Reservoirs and Dams), ICOLD (International Commission on Large Dams). However, though playing a critical role in estimating reservoir storage variations from remote sensing or hydrological models, area-storage (or elevation-storage) curves of reservoirs are not publicly shared. In this paper, we combine Landsat surface water extent, 1 arc-minute global relief model (ETOPO1) and GRanD database to derive area-storage curves of global reservoirs whose area is larger than 1 km2 (6,000 more reservoirs are included). First, the coverage polygon of each reservoir in GRanD is extended to where water was detected by Landsat during 1985-2015. Second, elevation of each pixel in the reservoir is extracted from resampled 30-meter ETOPO1, and then relative depth and frequency of each depth value is calculated. Third, cumulative storage is calculated with increasing water area by every one percent of reservoir coverage area and then the uncalibrated area-storage curve is obtained. Finally, the area-storage curve is linearly calibrated by the ratio of calculated capacity over reported capacity in GRanD. The derived curves are compared with in-situ reservoir data collected in Great Plains Region in US, and the results show that in-situ records are well captured by the derived curves even in relative small reservoirs (several square kilometers). The new derived area-storage curves have the potential to be employed in global monitoring or modelling of reservoirs storage and area variations.

The Analysis of RDF Semantic Data Storage Optimization in Large Data Era

Science.gov (United States)

He, Dandan; Wang, Lijuan; Wang, Can

2018-03-01

With the continuous development of information technology and network technology in China, the Internet has also ushered in the era of large data. In order to obtain the effective acquisition of information in the era of large data, it is necessary to optimize the existing RDF semantic data storage and realize the effective query of various data. This paper discusses the storage optimization of RDF semantic data under large data.

The carbon dioxide capture and geological storage

International Nuclear Information System (INIS)

2006-06-01

This road-map proposes by the Group Total aims to inform the public on the carbon dioxide capture and geological storage. One possible means of climate change mitigation consists of storing the CO 2 generated by the greenhouse gases emission in order to stabilize atmospheric concentrations. This sheet presents the CO 2 capture from lage fossil-fueled combustion installations, the three capture techniques and the CO 2 transport options, the geological storage of the CO 2 and Total commitments in the domain. (A.L.B.)

Effects of Dry Storage and Resubmersion of Oysters on Total Vibrio vulnificus and Total and Pathogenic (tdh+/trh+) Vibrio parahaemolyticus Levels.

Science.gov (United States)

Kinsey, Thomas P; Lydon, Keri A; Bowers, John C; Jones, Jessica L

2015-08-01

Vibrio vulnificus (Vv) and Vibrio parahaemolyticus (Vp) are the two leading causes of bacterial illnesses associated with raw shellfish consumption. Levels of these pathogens in oysters can increase during routine antifouling aquaculture practices involving dry storage in ambient air conditions. After storage, common practice is to resubmerge these stored oysters to reduce elevated Vv and Vp levels, but evidence proving the effectiveness of this practice is lacking. This study examined the changes in Vv and in total and pathogenic (thermostable direct hemolysin gene and the tdh-related hemolysin gene, tdh+ and trh+) Vp levels in oysters after 5 or 24 h of dry storage (28 to 32°C), followed by resubmersion (27 to 32°C) for 14 days. For each trial, replicate oyster samples were collected at initial harvest, after dry storage, after 7 days, and after 14 days of resubmersion. Oysters not subjected to dry storage were collected and analyzed to determine natural undisturbed vibrio levels (background control). Vibrio levels were measured using a most-probable-number enrichment followed by real-time PCR. After storage, vibrio levels (excluding tdh+ and trh+ Vp during 5-h storage) increased significantly (P oysters stored for 5 h) were not significantly different (P oysters. Vv and total and pathogenic Vp levels were not significantly different (P > 0.1) from levels in background oysters after 14 days of resubmersion, regardless of dry storage time. These data demonstrate that oyster resubmersion after dry storage at elevated ambient temperatures allows vibrio levels to return to those of background control samples. These results can be used to help minimize the risk of Vv and Vp illnesses and to inform the oyster industry on the effectiveness of routine storing and resubmerging of aquaculture oysters.

Application of 6D Building Information Model (6D BIM) for Business-storage Building in Slovenia

Science.gov (United States)

Pučko, Zoran; Vincek, Dražen; Štrukelj, Andrej; Šuman, Nataša

2017-10-01

The aim of this paper is to present an application of 6D building information modelling (6D BIM) on a real business-storage building in Slovenia. First, features of building maintenance in general are described according to the current Slovenian legislation, and also a general principle of BIM is given. After that, step-by-step activities for modelling 6D BIM are exposed, namely from Element list for maintenance, determination of their lifetime and service measures, cost analysing and time analysing to 6D BIM modelling. The presented 6D BIM model is designed in a unique way in which cost analysis is performed as 5D BIM model with linked data to use BIM Construction Project Management Software (Vico Office), integrated with 3D BIM model, whereas time analysis as 4D BIM model is carried out as non-linked data with the help of Excel (without connection to 3D BIM model). The paper is intended to serve as a guide to the building owners to prepare 6D BIM and to provide an insight into the relevant dynamic information about intervals and costs for execution of maintenance works in the whole building lifecycle.

Final storage of radioactive waste

International Nuclear Information System (INIS)

Albrecht, E.; Kolditz, H.; Thielemann, K.; Duerr, K.; Klarr, K.; Kuehn, K.; Staupendahl, G.; Uerpmann, E.P.; Bechthold, W.; Diefenbacher, W.

1974-12-01

The present report - presented by the Gesellschaft fuer Strahlen- und Umweltforschung mbH, Muenchen in cooperation with the Gesellschaft fuer Kernforschung mbH, Karlsruhe - gives a survey of the 1973 work in the field of final storage of radioactive wastes. The mining and constructional work carried out aboveground and underground in the saline of Asse near Remlingen with a view to repair, maintenance and expansion for future tasks is discussed. Storage of slightly active wastes on the 750 m floor and the tentative storage of medium-activity wastes on the 490 m floor were continued in the time under review. In September, the multiple transport container S 7 V, developped in the GfK for transports of 7 200 l iron-hooped drums containing medium activity wastes, were employed in Asse for the first time. With two transports a week between Karlsruhe Nuclear Research Centre and the Asse mine, 14 drums were stored per week with a total of 233 drums at the end of the year. The report also gives information on the present state of research in the fields of mountain engineering geology and hydrology, and its results. In addition, new storage methods are mentioned which are still in the planning stage. (orig./AK) [de

Bioinspired fractal electrodes for solar energy storages.

Science.gov (United States)

Thekkekara, Litty V; Gu, Min

2017-03-31

Solar energy storage is an emerging technology which can promote the solar energy as the primary source of electricity. Recent development of laser scribed graphene electrodes exhibiting a high electrical conductivity have enabled a green technology platform for supercapacitor-based energy storage, resulting in cost-effective, environment-friendly features, and consequent readiness for on-chip integration. Due to the limitation of the ion-accessible active porous surface area, the energy densities of these supercapacitors are restricted below ~3 × 10 -3  Whcm -3 . In this paper, we demonstrate a new design of biomimetic laser scribed graphene electrodes for solar energy storage, which embraces the structure of Fern leaves characterized by the geometric family of space filling curves of fractals. This new conceptual design removes the limit of the conventional planar supercapacitors by significantly increasing the ratio of active surface area to volume of the new electrodes and reducing the electrolyte ionic path. The attained energy density is thus significantly increased to ~10 -1  Whcm -3 - more than 30 times higher than that achievable by the planar electrodes with ~95% coulombic efficiency of the solar energy storage. The energy storages with these novel electrodes open the prospects of efficient self-powered and solar-powered wearable, flexible and portable applications.

Bioinspired fractal electrodes for solar energy storages

Science.gov (United States)

Thekkekara, Litty V.; Gu, Min

2017-03-01

Solar energy storage is an emerging technology which can promote the solar energy as the primary source of electricity. Recent development of laser scribed graphene electrodes exhibiting a high electrical conductivity have enabled a green technology platform for supercapacitor-based energy storage, resulting in cost-effective, environment-friendly features, and consequent readiness for on-chip integration. Due to the limitation of the ion-accessible active porous surface area, the energy densities of these supercapacitors are restricted below ~3 × 10-3 Whcm-3. In this paper, we demonstrate a new design of biomimetic laser scribed graphene electrodes for solar energy storage, which embraces the structure of Fern leaves characterized by the geometric family of space filling curves of fractals. This new conceptual design removes the limit of the conventional planar supercapacitors by significantly increasing the ratio of active surface area to volume of the new electrodes and reducing the electrolyte ionic path. The attained energy density is thus significantly increased to ~10-1 Whcm-3- more than 30 times higher than that achievable by the planar electrodes with ~95% coulombic efficiency of the solar energy storage. The energy storages with these novel electrodes open the prospects of efficient self-powered and solar-powered wearable, flexible and portable applications.

Evaluation of ZFS as an efficient WLCG storage backend

Science.gov (United States)

Ebert, M.; Washbrook, A.

2017-10-01

A ZFS based software raid system was tested for performance against a hardware raid system providing storage based on the traditional Linux file systems XFS and EXT4. These tests were done for a healthy raid array as well as for a degraded raid array and during the rebuild of a raid array. It was found that ZFS performs better in almost all test scenarios. In addition, distinct features of ZFS were tested for WLCG data storage use, like compression and higher raid levels with triple redundancy information. The long term reliability was observed after converting all production storage servers at the Edinburgh WLCG Tier-2 site to ZFS, resulting in about 1.2PB of ZFS based storage at this site.

Proceedings of the 1981 National Waste Terminal Storage Program information meeting

International Nuclear Information System (INIS)

1981-11-01

Separate abstracts have been prepared for each of the following sixteen sections: Overview of the National Waste Terminal Storage Program; Site Characterization; Repository Development; Regulatory Framework; Systems; Socioeconomic Evaluation; Site Screening/Characterization Support Activities; Repository Data Base Development; Regulatory Implementation; Systems Performance Assessment; Sociopolitical Initiatives; Earth Sciences; International Waste Management; Waste Package Development; Quality Assurance; and Overviews of NWTS Projects

Dry spent fuel storage experience at overseas nuclear stations focus USA

International Nuclear Information System (INIS)

Bradley, T. L.; Kumar, S.; Marcelli, D. G.

1997-01-01

This paper provides a summary of US dry spent fuel storage experience, including application of this experience outside the United States. Background information on the US nuclear and spent fuel storage industry is provided as a basis for discussing the various types of options and systems available. An overview of technology options is presented, including systems being used and/or considered by the US government and private sector, as well as a discussion of overall system design, licensing and operation. Factors involved in selecting the best available technology option for a specific site or group of sites are presented, along with a typical timeline for project implementation. Cross-geographical use of technologies under different regulatory and technological regimes is also discussed. The paper concludes that dry storage is safe and reliable based on a successful ten year period. The information presented may be considered for use in the development of dry spent fuel storage in Korea and other countries. (author)

effects of extended period of storage and strain of layer on quality

African Journals Online (AJOL)

User

strain of layers and extended storage length on internal and external qualities of chicken eggs. ... storage of egg on some important egg quality determinants like egg weight, albumen height and ... of information on the quality of eggs of these.

A concept of an electricity storage system with 50 MWh storage capacity

Directory of Open Access Journals (Sweden)

Józef Paska

2012-06-01

Full Text Available Electricity storage devices can be divided into indirect storage technology devices (involving electricity conversion into another form of energy, and direct storage (in an electric or magnetic fi eld. Electricity storage technologies include: pumped-storage power plants, BES Battery Energy Storage, CAES Compressed Air Energy Storage, Supercapacitors, FES Flywheel Energy Storage, SMES Superconducting Magnetic Energy Storage, FC Fuel Cells reverse or operated in systems with electrolysers and hydrogen storage. These technologies have diff erent technical characteristics and economic parameters that determine their usability. This paper presents two concepts of an electricity storage tank with a storage capacity of at least 50 MWh, using the BES battery energy storage and CAES compressed air energy storage technologies.

Predicting long-term performance of engineered geologic carbon dioxide storage systems to inform decisions amidst uncertainty

Science.gov (United States)

Pawar, R.

2016-12-01

Risk assessment and risk management of engineered geologic CO2 storage systems is an area of active investigation. The potential geologic CO2 storage systems currently under consideration are inherently heterogeneous and have limited to no characterization data. Effective risk management decisions to ensure safe, long-term CO2 storage requires assessing and quantifying risks while taking into account the uncertainties in a storage site's characteristics. The key decisions are typically related to definition of area of review, effective monitoring strategy and monitoring duration, potential of leakage and associated impacts, etc. A quantitative methodology for predicting a sequestration site's long-term performance is critical for making key decisions necessary for successful deployment of commercial scale geologic storage projects where projects will require quantitative assessments of potential long-term liabilities. An integrated assessment modeling (IAM) paradigm which treats a geologic CO2 storage site as a system made up of various linked subsystems can be used to predict long-term performance. The subsystems include storage reservoir, seals, potential leakage pathways (such as wellbores, natural fractures/faults) and receptors (such as shallow groundwater aquifers). CO2 movement within each of the subsystems and resulting interactions are captured through reduced order models (ROMs). The ROMs capture the complex physical/chemical interactions resulting due to CO2 movement and interactions but are computationally extremely efficient. The computational efficiency allows for performing Monte Carlo simulations necessary for quantitative probabilistic risk assessment. We have used the IAM to predict long-term performance of geologic CO2 sequestration systems and to answer questions related to probability of leakage of CO2 through wellbores, impact of CO2/brine leakage into shallow aquifer, etc. Answers to such questions are critical in making key risk management

Initial Operation of the Savannah River Site Advanced Storage Monitoring Facility

International Nuclear Information System (INIS)

McCurry, D.R.

2001-01-01

An advanced storage monitoring facility has been constructed at the Savannah River Site capable of storing sensitive nuclear materials (SNM) with access to monitoring information available over the Internet. This system will also have monitoring information available over the Internet to appropriate users. The programs will ultimately supply authenticated and encrypted data from the storage sites to certified users to demonstrate the capability of using the Internet as a safe and secure communications medium for remote monitoring of sensitive items

Preliminary Study of Favourable Formations for CO2 Subsurface Storage in Spain

International Nuclear Information System (INIS)

Zapatero, M. A.; Reyes, J. L.; Martinez, R.; Suarez, I.; Arenillas, A.; Perucha, M. A.

2009-01-01

This report is a synthesis of the possibilities of CO 2 storage in the Spanish subsurface. Compilation and analysis of geological information has been carried out, looking at surface and subsurface, in order to make a pre-selection of potential favourable units for CO 2 storage, taking in account that each of this storages needs a confining formation to seal the storage. Before the storage selection, a general description of the great geological units of the Iberian Peninsula is done. Afterwards, borehole logging from petroleum exploration is analysed in these units, formations and areas of interest. The aim is to finally obtain a description of selected units and their possibilities of CO 2 storage. (Author) 17 refs

Benchmarking personal cloud storage

NARCIS (Netherlands)

Drago, Idilio; Bocchi, Enrico; Mellia, Marco; Slatman, Herman; Pras, Aiko

2013-01-01

Personal cloud storage services are data-intensive applications already producing a significant share of Internet traffic. Several solutions offered by different companies attract more and more people. However, little is known about each service capabilities, architecture and - most of all -

Simulation of interim spent fuel storage system with discrete event model

International Nuclear Information System (INIS)

Yoon, Wan Ki; Song, Ki Chan; Lee, Jae Sol; Park, Hyun Soo

1989-01-01

This paper describes dynamic simulation of the spent fuel storage system which is described by statistical discrete event models. It visualizes flow and queue of system over time, assesses the operational performance of the system activities and establishes the system components and streams. It gives information on system organization and operation policy with reference to the design. System was tested and analyzed over a number of critical parameters to establish the optimal system. Workforce schedule and resources with long processing time dominate process. A combination of two workforce shifts a day and two cooling pits gives the optimal solution of storage system. Discrete system simulation is an useful tool to get information on optimal design and operation of the storage system. (Author)

Surface sterilization and duration of seed storage influenced ...

African Journals Online (AJOL)

The effects of factorial combinations of four storage duration (in days after seed extraction) and surface sterilization with three dilution levels of sodium hypochlorite on seedling emergence and seedling quality of African breadfruit were studied. Storage duration significantly influenced days to seedling emergence, ...

Comparison of quality attributes of buffalo meat curry at different storage temperature.

Science.gov (United States)

Kandeepan, Gurunathan; Anjaneyulu, Anne Seet Ram; Kondaiah, Napa; Mendiratta, Sanjod Kumar

2011-01-01

The product quality of curry is determined by the food animal source, raw materials and the method of processing. Moreover the scientific information on processing and quality of traditional buffalo meat curry from different groups of buffaloes is not available. This study was undertaken to develop processed curry from different buffalo groups and to compare its quality during storage at ambient and refrigeration temperature. The meat samples were collected from the longissimus dorsi muscle of the carcasses from each group of buffaloes slaughtered according to the traditional halal method. Buffalo meat curry was prepared in a pressure cooker with the standardized formulation. This final product was subjected to evaluation of quality and shelf life. To evaluate the effect of different groups of meat samples on the quality of curry, product yield, pH, proximate composition, water activity (aw), thiobarbituric acid reactive substances (TBARS), calorific value, sensory attributes and microbiological assay were determined The energy of meat curry from young buffaloes was significantly lower than the meat curry from spent animal groups. The overall acceptability of curry decreased significantly during 3 days ambient storage compared to refrigeration storage. Scientific processing by adopting good manufacturing practices and suitable packaging helped greatly to improve the shelf life of the ambient temperature stored buffalo meat curry. Buffalo meat curry from young male group showed better product characteristics and overall acceptability scores than spent buffalo group.

Seneca Compressed Air Energy Storage (CAES) Project

Energy Technology Data Exchange (ETDEWEB)

None

2012-11-30

This document provides specifications for the process air compressor for a compressed air storage project, requests a budgetary quote, and provides supporting information, including compressor data, site specific data, water analysis, and Seneca CAES value drivers.

Opportunities in independent gas storage

International Nuclear Information System (INIS)

Daniel, R.

1999-01-01

The range of business opportunities currently available for the midstream oil and gas business were discussed with particular focus on storage opportunities. Alberta Energy Co. (AEC) Ltd.'s two midstream business units include AEC Pipelines and Gas Processing, and AEC Storage and Hub Services. These two businesses provide the company with good investment returns, stable cash flow, and some significant strategic synergies with their exploration and production businesses. In 1988, the AECO C Hub in southeastern Alberta was created as an outgrowth of AEC's gas production operations on the Suffield block, where they had depleted gas reservoirs with high rock quality suitable for high deliverability storage. With the AECO C Hub, AEC was able to offer firm storage contracts of from 1 to 20 years, and to introduce short term interruptible parking and lending services, title exchange, a spot price index for greater price discovery, and an electronic nomination system. AEC is currently completing construction of their second commercial storage facility, the Wild Goose project, in northern California. D ebottlenecking' the Western Canada supply basin should provide additional opportunities for further expansion not only for AEC but also for other midstream service providers. Opportunities are especially available in the areas of new storage facilities to serve location-specific needs, replacement of declining storage capacity, replacement of retiring facilities, technological optimization of existing facilities, more flexible, higher deliverability facilities and commercial optimization of existing facilities. A map of the hubs and market centres of North America are included. 5 figs

The U. S. DOE Carbon Storage Program: Status and Future Directions

Science.gov (United States)

Damiani, D.

2016-12-01

The U.S. Department of Energy (DOE) is taking steps to reduce carbon dioxide (CO2) emissions through clean energy innovation, including carbon capture and storage (CCS) research. The Office of Fossil Energy Carbon Storage Program is focused on ensuring the safe and permanent storage and/or utilization of CO2 captured from stationary sources. The Program is developing and advancing geologic storage technologies both onshore and offshore that will significantly improve the effectiveness of CCS, reduce the cost of implementation, and be ready for widespread commercial deployment in the 2025-2035 timeframe. The technology development and field testing conducted through this Program will be used to benefit the existing and future fleet of fossil fuel power generating and industrial facilities by creating tools to increase our understanding of geologic reservoirs appropriate for CO2 storage and the behavior of CO2 in the subsurface. The Program is evaluating the potential for storage in depleted oil and gas reservoirs, saline formations, unmineable coal, organic-rich shale formations, and basalt formations. Since 1997, DOE's Carbon Storage Program has significantly advanced the CCS knowledge base through a diverse portfolio of applied research projects. The Core Storage R&D research component focuses on analytic studies, laboratory, and pilot- scale research to develop technologies that can improve wellbore integrity, increase reservoir storage efficiency, improve management of reservoir pressure, ensure storage permanence, quantitatively assess risks, and identify and mitigate potential release of CO2 in all types of storage formations. The Storage Field Management component focuses on scale-up of CCS and involves field validation of technology options, including large-volume injection field projects at pre-commercial scale to confirm system performance and economics. Future research involves commercial-scale characterization for regionally significant storage locations

Tritium storage

International Nuclear Information System (INIS)

Hircq, B.

1990-01-01

This document represents a synthesis relative to tritium storage. After indicating the main storage particularities as regards tritium, storages under gaseous and solid form are after examined before establishing choices as a function of the main criteria. Finally, tritium storage is discussed regarding tritium devices associated to Fusion Reactors and regarding smaller devices [fr

Energy storage

International Nuclear Information System (INIS)

2012-01-01

After having outlined the importance of energy storage in the present context, this document outlines that it is an answer to economic, environmental and technological issues. It proposes a brief overview of the various techniques of energy storage: under the form of chemical energy (hydrocarbons, biomass, hydrogen production), thermal energy (sensitive or latent heat storage), mechanical energy (potential energy by hydraulic or compressed air storage, kinetic energy with flywheels), electrochemical energy (in batteries), electric energy (super-capacitors, superconductor magnetic energy storage). Perspectives are briefly evoked

Modeling of battery energy storage in the National Energy Modeling System

Energy Technology Data Exchange (ETDEWEB)

Swaminathan, S.; Flynn, W.T.; Sen, R.K. [Sentech, Inc., Bethesda, MD (United States)

1997-12-01

The National Energy Modeling System (NEMS) developed by the U.S. Department of Energy`s Energy Information Administration is a well-recognized model that is used to project the potential impact of new electric generation technologies. The NEMS model does not presently have the capability to model energy storage on the national grid. The scope of this study was to assess the feasibility of, and make recommendations for, the modeling of battery energy storage systems in the Electricity Market of the NEMS. Incorporating storage within the NEMS will allow the national benefits of storage technologies to be evaluated.

Potential problem areas: extended storage of low-level radioactive waste

Energy Technology Data Exchange (ETDEWEB)

Siskind, B.

1985-01-01

If a state or regional compact does not have adequate disposal capacity for low-level radioactive waste (LLRW), then extended storage of certain LLRW may be necessary. The Nuclear Regulatory Commission (NRC) has contracted with Brookhaven National Laboratory to address the technical issues of extended storage. The dual objectives of this study are (1) to provide practical technical assessments for NRC to consider in evaluating specific proposals for extended storage and (2) to help ensure adequate consideration by NRC, Agreement States, and licensees of potential problems that may arise from existing or proposed extended storage practices. Storage alternatives are considered in order to characterize the likely storage environments for these wastes. In particular, the range of storage alternatives considered and being implemented by the nuclear power plant utilities is described. The properties of the waste forms and waste containers are discussed. An overview is given of the performance of the waste package and its contents during storage (e.g., radiolytic gas generation, corrosion) and of the effects of extended storage on the performance of the waste package after storage (e.g., radiation-induced embrittlement of polyethylene, the weakening of steel containers by corrosion). Additional information and actions required to address these concerns, including possible mitigative measures, are discussed. 26 refs., 1 tab.

Storage of Quantum Variables in Atomic Media

DEFF Research Database (Denmark)

Cviklinski, J.; Ortalo, J.; Josse, V.

2007-01-01

Storage and read-out of non classical states of light is a critical element for quantum information networks. Simultaneous storage of two non-commuting variables carried by light and subsequent read-out is shown to be possible in atomic ensembles. Interaction of light fields with three-level syst......-level systems allows direct mapping the quantum state of light into long lived coherences in the atomic ground state. We show that excess noise linked to atomic transitions can be made negligible. Experimental developments are discussed for atomic vapours and cold atoms....

Monitoring small reservoirs' storage with satellite remote sensing in inaccessible areas

Science.gov (United States)

Avisse, Nicolas; Tilmant, Amaury; François Müller, Marc; Zhang, Hua

2017-12-01

In river basins with water storage facilities, the availability of regularly updated information on reservoir level and capacity is of paramount importance for the effective management of those systems. However, for the vast majority of reservoirs around the world, storage levels are either not measured or not readily available due to financial, political, or legal considerations. This paper proposes a novel approach using Landsat imagery and digital elevation models (DEMs) to retrieve information on storage variations in any inaccessible region. Unlike existing approaches, the method does not require any in situ measurement and is appropriate for monitoring small, and often undocumented, irrigation reservoirs. It consists of three recovery steps: (i) a 2-D dynamic classification of Landsat spectral band information to quantify the surface area of water, (ii) a statistical correction of DEM data to characterize the topography of each reservoir, and (iii) a 3-D reconstruction algorithm to correct for clouds and Landsat 7 Scan Line Corrector failure. The method is applied to quantify reservoir storage in the Yarmouk basin in southern Syria, where ground monitoring is impeded by the ongoing civil war. It is validated against available in situ measurements in neighbouring Jordanian reservoirs. Coefficients of determination range from 0.69 to 0.84, and the normalized root-mean-square error from 10 to 16 % for storage estimations on six Jordanian reservoirs with maximal water surface areas ranging from 0.59 to 3.79 km2.

High density energy storage capacitor

International Nuclear Information System (INIS)

Whitham, K.; Howland, M.M.; Hutzler, J.R.

1979-01-01

The Nova laser system will use 130 MJ of capacitive energy storage and have a peak power capability of 250,000 MW. This capacitor bank is a significant portion of the laser cost and requires a large portion of the physical facilities. In order to reduce the cost and volume required by the bank, the Laser Fusion Program funded contracts with three energy storage capacitor producers: Aerovox, G.E., and Maxwell Laboratories, to develop higher energy density, lower cost energy storage capacitors. This paper describes the designs which resulted from the Aerovox development contract, and specifically addresses the design and initial life testing of a 12.5 kJ, 22 kV capacitor with a density of 4.2 J/in 3 and a projected cost in the range of 5 cents per joule

What is plutonium stabilization, and what is safe storage of plutonium?

International Nuclear Information System (INIS)

Forsberg, C.W.

1995-01-01

The end of the cold war has resulted in the shutdown of nuclear weapons production and the start of dismantlement of significant numbers of nuclear weapons. This, in turn, is creating an inventory of plutonium requiring interim and long-term storage. A key question is, ''What is required for safe, multidecade, plutonium storage?'' The requirements for storage, in turn, define what is needed to stabilize the plutonium from its current condition into a form acceptable for interim and long-term storage. Storage requirements determine if research is required to (1) define required technical conditions for interim and long-term storage and (2) develop or improve current stabilization technologies. Storage requirements depend upon technical, policy, and economic factors. The technical issues are complicated by several factors. Plutonium in aerosol form is highly hazardous. Plutonium in water is hazardous. The plutonium inventory is in multiple chemical forms--some of which are chemically reactive. Also, some of the existing storage forms are clearly unsuitable for storage periods over a few years. Gas generation by plutonium compounds complicates storage: (1) all plutonium slowly decays creating gaseous helium and (2) the radiation from plutonium decay can initiate many chemical reactions-some of which generate significant quantities of gases. Gas generation can pressurize sealed storage packages. Last nuclear criticality must be avoided

Critical Factors for Personal Cloud Storage Adoption in China

Directory of Open Access Journals (Sweden)

Jianya Wang

2016-06-01

Full Text Available Purpose: In order to explain and predict the adoption of personal cloud storage, this study explores the critical factors involved in the adoption of personal cloud storage and empirically validates their relationships to a user's intentions. Design/methodology/approach: Based on technology acceptance model (TAM, network externality, trust, and an interview survey, this study proposes a personal cloud storage adoption model. We conducted an empirical analysis by structural equation modeling based on survey data obtained with a questionnaire. Findings: Among the adoption factors we identified, network externality has the salient influence on a user's adoption intention, followed by perceived usefulness, individual innovation, perceived trust, perceived ease of use, and subjective norms. Cloud storage characteristics are the most important indirect factors, followed by awareness to personal cloud storage and perceived risk. However, although perceived risk is regarded as an important factor by other cloud computing researchers, we found that it has no significant influence. Also, subjective norms have no significant influence on perceived usefulness. This indicates that users are rational when they choose whether to adopt personal cloud storage. Research limitations: This study ignores time and cost factors that might affect a user's intention to adopt personal cloud storage. Practical implications: Our findings might be helpful in designing and developing personal cloud storage products, and helpful to regulators crafting policies. Originality/value: This study is one of the first research efforts that discuss Chinese users' personal cloud storage adoption, which should help to further the understanding of personal cloud adoption behavior among Chinese users.

Handling and storage of conditioned high-level wastes

International Nuclear Information System (INIS)

1983-01-01

This report deals with certain aspects of the management of one of the most important wastes, i.e. the handling and storage of conditioned (immobilized and packaged) high-level waste from the reprocessing of spent nuclear fuel and, although much of the material presented here is based on information concerning high-level waste from reprocessing LWR fuel, the principles, as well as many of the details involved, are applicable to all fuel types. The report provides illustrative background material on the arising and characteristics of high-level wastes and, qualitatively, their requirements for conditioning. The report introduces the principles important in conditioned high-level waste storage and describes the types of equipment and facilities, used or studied, for handling and storage of such waste. Finally, it discusses the safety and economic aspects that are considered in the design and operation of handling and storage facilities

Manufacturing and Construction of Fresh Fuel Storage Rack for a Research Reactor

Energy Technology Data Exchange (ETDEWEB)

Oh, Jinho; Lee, Sangjin; Lee, Jongmin; Ryu, Jeong-Soo [KAERI, Daejeon (Korea, Republic of)

2016-05-15

The objective of this study is to provide the manufacturing and construction information regarding the Fresh Fuel Storage Rack (FFSR). The main function of a FFSR is to store and protect the 2 core new fuel assemblies for the operation of the research reactor. The fresh fuel assemblies are stored in a rack made of stainless steel and the storage rack is installed in the fresh fuel storage room. The fresh fuel facility provides fresh fuel assemblies with dry storage space. General design requirements of the fresh fuel storage facilities are given in the ANSI-57.3. Design, manufacturing, and construction of the fresh fuel storage rack are introduced. The analysis is performed to confirm the structural intensity of the fresh fuel storage rack under the seismic loads. The fresh fuel storage rack designed for storage of fresh fuel assemblies should be manufactured and installed with consideration of predicted number of fresh fuel assemblies, structural integrity, resistivity to corrosion and radiation, cleaning, and workability.

Manufacturing and Construction of Fresh Fuel Storage Rack for a Research Reactor

International Nuclear Information System (INIS)

Oh, Jinho; Lee, Sangjin; Lee, Jongmin; Ryu, Jeong-Soo

2016-01-01

The objective of this study is to provide the manufacturing and construction information regarding the Fresh Fuel Storage Rack (FFSR). The main function of a FFSR is to store and protect the 2 core new fuel assemblies for the operation of the research reactor. The fresh fuel assemblies are stored in a rack made of stainless steel and the storage rack is installed in the fresh fuel storage room. The fresh fuel facility provides fresh fuel assemblies with dry storage space. General design requirements of the fresh fuel storage facilities are given in the ANSI-57.3. Design, manufacturing, and construction of the fresh fuel storage rack are introduced. The analysis is performed to confirm the structural intensity of the fresh fuel storage rack under the seismic loads. The fresh fuel storage rack designed for storage of fresh fuel assemblies should be manufactured and installed with consideration of predicted number of fresh fuel assemblies, structural integrity, resistivity to corrosion and radiation, cleaning, and workability

Risk management guidelines for petroleum storage tank sites

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-10-01

These guidelines provide a site management process designed particularly for soil and groundwater pollution originating from existing or former petroleum storage tank (PST) facilities and provide uniform standards for the remediation of polluted PST sites in Alberta. The numerical criteria, risk management objectives and technical information described in this document were compiled from four documents including Remediation Guidelines for Petroleum Storage Tank Sites 1994, the Canada-Wide Standards for Petroleum Hydrocarbons in Soil, Alberta Soil and Water Quality Guidelines for Hydrocarbons at Upstream Oil and Gas Facilities, and Guidelines for Managing Risks at Contaminated Sites in Alberta. The changes in these updated guidelines reflect new remediation criteria and provide a process for determining alternate site-specific management objectives for more petroleum storage tank sites. The guidelines were developed using a risk-based approach that ensures the protection of human health, safety and the environment. The guidelines apply to aboveground and underground storage tank facilities that contain gasoline, diesel, heating oil, and aviation fuel. The guidelines specify requirements by Alberta Environment and the Alberta Fire Code. The chapter on risk management process included information on site investigation, determination of soil type, pollution source removal, land use assessment, selection of exposure pathways, depth of remediation, human inhalation and groundwater protection pathways, and verification of remediation. figs, 4 tabs., 2 appendices.

Annual report 1999. Department of wastes disposal and storage

International Nuclear Information System (INIS)

2000-01-01

This annual report presents the organization, the personnel, the collaborations, the scientific researches and the publications of the Department of wastes disposal and storage of the CEA. A thematic presentation of the research and development programs is provided bringing information on the liquid effluents processing, the materials and solid wastes processing, the wastes conditioning, the characterization, the storage, the radionuclides chemistry and migration, the dismantling and the environment. (A.L.B.)

Oxidative deterioration of pork during superchilling storage.

Science.gov (United States)

Pomponio, Luigi; Ruiz-Carrascal, Jorge

2017-12-01

In superchilling (SC), meat is kept at temperatures around 1 °C below its initial freezing point, leading to a significant increase in shelf life. This study aimed to address the oxidative changes taking place in pork loins during prolonged storage at SC temperature. Loins were stored either at chilling (CH) conditions (2-4 °C) for 4 weeks or at SC temperature (around -1 °C) for 12 weeks. Storage at SC temperature diminished the rate of lipid and protein oxidation and discoloration in pork loins, so that final levels of most oxidation products and instrumental color values after 12 weeks of SC storage were similar to those after 4 weeks at CH conditions. However, hexanal content peaked by the end of SC storage, pointing to a potential accumulation of compounds from lipid oxidation during SC storage. SC storage of pork slows down the rate of lipid and protein oxidation. However, accumulation of volatile compounds from lipid oxidation could be a limiting factor for shelf life. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Aube storage centres - 2007 review

International Nuclear Information System (INIS)

2008-10-01

The National Radioactive Waste Management Agency (Andra), was established by the December 1991 Waste Act as a public body in charge of the long-term management of all radioactive waste, under the supervision of the Ministry of Ecology, Energy, Sustainable Development and the Sea (formerly the Ministry of Industry and the Ministry of Environment), and the Ministry of Research. The Andra operates two storage centers in the Aube region (France): the center for short-lived low- and intermediate-level wastes, and the center for very-low-level radioactive wastes. This report presents a review of the activities of both centers for 2007: deliveries, storage and processing, maintenance, incidents, personnel security, installations and environmental monitoring, effluents, budget and revenues, personnel, taxes, public information and actions of communication

Aube storage centres - 2005 review

International Nuclear Information System (INIS)

2006-07-01

The National Radioactive Waste Management Agency (Andra), was established by the December 1991 Waste Act as a public body in charge of the long-term management of all radioactive waste, under the supervision of the Ministry of Ecology, Energy, Sustainable Development and the Sea (formerly the Ministry of Industry and the Ministry of Environment), and the Ministry of Research. The Andra operates two storage centers in the Aube region (France): the center for short-lived low- and intermediate-level wastes, and the center for very-low-level radioactive wastes. This report presents a review of the activities of both centers for 2005: deliveries, storage and processing, maintenance, incidents, personnel security, installations and environmental monitoring, effluents, budget and revenues, personnel, taxes, public information and actions of communication

Application of energy storage devices in power systems

African Journals Online (AJOL)

user

paper concentrates on performance benefits of adding energy storage to power ..... Because of geographical, environmental, and cost constraints, construction of pumped .... transport, in Information Day on Non-Nuclear Energy RTD, Brussels.

Energy storage for power systems

CERN Document Server

Ter-Gazarian, Andrei

2011-01-01

The supply of energy from primary sources is not constant and rarely matches the pattern of demand from consumers. Electricity is also difficult to store in significant quantities. Therefore, secondary storage of energy is essential to increase generation capacity efficiency and to allow more substantial use of renewable energy sources that only provide energy intermittently. Lack of effective storage has often been cited as a major hurdle to substantial introduction of renewable energy sources into the electricity supply network.This 2nd edition, without changing the existing structure of the

Extended storage of low-level radioactive waste: potential problem areas

International Nuclear Information System (INIS)

Siskind, B.; Dougherty, D.R.; MacKenzie, D.R.

1985-12-01

If a state or state compact does not have adequate disposal capacity for low-level radioactive waste (LLRW) by 1986 as required by the Low-Level Waste Policy Act, then extended storage of certain LLRW may be necessary. In this report, extended storage of LLRW is considered in order to determine for the Nuclear Regulatory Commission areas of concern and actions recommended to resolve these concerns. The focus is on the properties and performance of the waste form and waste container. Storage alternatives are considered in order to characterize the likely storage environments for these wastes. The areas of concern about extended storage of LLRW are grouped into two categories: (1) Performance of the waste form and/or container during storage, e.g., radiolytic gas generation, radiation-enhanced degradation of polymeric materials, and corrosion. (2) Effects of extended storage on the properties of the waste form and/or container that are important after storage (e.g., radiation-induced embrittlement of high-density polyethylene and the weakening of steel containers resulting from corrosion). A discussion is given of additional information and actions required to address these concerns

New technology and possible advances in energy storage

International Nuclear Information System (INIS)

Baker, John

2008-01-01

Energy storage technologies may be electrical or thermal. Electrical energy stores have an electrical input and output to connect them to the system of which they form part, while thermal stores have a thermal input and output. The principal electrical energy storage technologies described are electrochemical systems (batteries and flow cells), kinetic energy storage (flywheels) and potential energy storage, in the form of pumped hydro and compressed air. Complementary thermal storage technologies include those based on the sensible and latent heat capacity of materials, which include bulk and smaller-capacity hot and cold water storage systems, ice storage, phase change materials and specific bespoke thermal storage media. For the majority of the storage technologies considered here, the potential for fundamental step changes in performance is limited. For electrochemical systems, basic chemistry suggests that lithium-based technologies represent the pinnacle of cell development. This means that the greatest potential for technological advances probably lies in the incremental development of existing technologies, facilitated by advances in materials science, engineering, processing and fabrication. These considerations are applicable to both electrical and thermal storage. Such incremental developments in the core storage technologies are likely to be complemented and supported by advances in systems integration and engineering. Future energy storage technologies may be expected to offer improved energy and power densities, although, in practice, gains in reliability, longevity, cycle life expectancy and cost may be more significant than increases in energy/powerdensity per se

Long-term data storage in diamond

OpenAIRE

Dhomkar, Siddharth; Henshaw, Jacob; Jayakumar, Harishankar; Meriles, Carlos A.

2016-01-01

The negatively charged nitrogen vacancy (NV?) center in diamond is the focus of widespread attention for applications ranging from quantum information processing to nanoscale metrology. Although most work so far has focused on the NV? optical and spin properties, control of the charge state promises complementary opportunities. One intriguing possibility is the long-term storage of information, a notion we hereby introduce using NV-rich, type 1b diamond. As a proof of principle, we use multic...

Underground storage tanks

International Nuclear Information System (INIS)

Anon.

1993-01-01

Environmental contamination from leaking underground storage tanks poses a significant threat to human health and the environment. An estimated five to six million underground storage tanks containing hazardous substances or petroleum products are in use in the US. Originally placed underground as a fire prevention measure, these tanks have substantially reduced the damages from stored flammable liquids. However, an estimated 400,000 underground tanks are thought to be leaking now, and many more will begin to leak in the near future. Products released from these leaking tanks can threaten groundwater supplies, damage sewer lines and buried cables, poison crops, and lead to fires and explosions. As required by the Hazardous and Solid Waste Amendments (HSWA), the EPA has been developing a comprehensive regulatory program for underground storage tanks. The EPA proposed three sets of regulations pertaining to underground tanks. The first addressed technical requirements for petroleum and hazardous substance tanks, including new tank performance standards, release detection, release reporting and investigation, corrective action, and tank closure. The second proposed regulation addresses financial responsibility requirements for underground petroleum tanks. The third addressed standards for approval of state tank programs

Safety aspects of dry spent fuel storage and spent fuel management

International Nuclear Information System (INIS)

Botsch, W.; Smalian, S.; Hinterding, P.; Voelzke, H.; Wolff, D.; Kasparek, E.

2014-01-01

The storage of spent nuclear fuel (SF) and high-level radioactive waste (HLW) must conform to safety requirements. Safety aspects like safe enclosure of radioactive materials, safe removal of decay heat, nuclear criticality safety and avoidance of unnecessary radiation exposure must be achieved throughout the storage period. The implementation of these safety requirements can be achieved by dry storage of SF and HLW in casks as well as in other systems such as dry vault storage systems or spent fuel pools, where the latter is neither a dry nor a passive system. In Germany dual purpose casks for SF or HLW are used for safe transportation and interim storage. TUV and BAM, who work as independent experts for the competent authorities, present the storage licensing process including sites and casks and inform about spent nuclear fuel management and issues concerning dry storage of spent nuclear fuel, based on their long experience in these fields (authors)

2010-2012. Research and development at the ANDRA for storage projects

International Nuclear Information System (INIS)

2013-10-01

After a general presentation of research activities within the ANDRA (main steps and highlights between 2010 and 2012, composition of the scientific council, actions of mobilisation of the French and international scientific community), this report proposes a detailed overview of these R and D activities in different specific fields: the determination of the behaviour of the various components of a storage (studies on wastes, on the behaviour of geological layers and of underground works, on the interaction and chemistry of materials in a deep storage), the preparation of the construction of the future deep storage in its geological context, the design of the evolution of a storage within its environment (effect of oxidation, of transfer phenomena within the storage, within the geological environment, and within soils), the assessment of storage performance, the reversibility of the deep geological storage and its implications in time, and the actions information on results and valorisation (congresses, publications, research thesis)

Economic efficiency of underground natural gas storage: The case of Canada

International Nuclear Information System (INIS)

Charette, Y.

1990-01-01

The paper describes the current situation of natural gas storage in Canada and attempts to provide valuable information and analytical tools so that the key players, including government and industry, will be in a better position to make enlightened choices for future investments in natural gas storage. Central to the analysis of the efficiency of storage is the notion of efficient peak-load pricing. It is usually recognized that storage may be efficient or welfare increasing because, with fixed consumption, it may allow the substitution of cheaper off-peak production for more costly production. The theoretical conclusions are used of a number of static peak-load pricing models, as well as investment decision models, to analyze the various costs and benefits of storage. The main conclusion is made that, when storage is possible, the welfare maximizing peak/off-peak price differential can be reduced, and therefore, storage can increase the efficiency of the gas transmission system. 10 refs, 2 figs, 5 tabs

Protocol for Uniformly Measuring and Expressing the Performance of Energy Storage Systems

Energy Technology Data Exchange (ETDEWEB)

Conover, David R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Crawford, Alasdair J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Fuller, Jason [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Gourisetti, Sri Nikhil [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Viswanathan, Vilayanur [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Ferreira, Summer Rhodes [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Schoenwald, David A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Rosewater, David Martin [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2016-04-01

This Protocol provides a set of “best practices” for characterizing energy storage systems (ESSs) and measuring and reporting their performance. It serves as a basis for assessing how an ESS will perform with respect to key performance attributes relevant to different applications. It is intended to provide a valid and accurate basis for the comparison of different ESSs. By achieving the stated purpose, the Protocol will enable more informed decision-making in the selection of ESSs for various stationary applications. The Protocol identifies general information and technical specifications relevant in describing an ESS and also defines a set of test, measurement, and evaluation criteria with which to express the performance of ESSs that are intended for energy-intensive and/or power-intensive stationary applications. An ESS includes a storage device, battery management system, and any power conversion systems installed with the storage device. The Protocol is agnostic with respect to the storage technology and the size and rating of the ESS. The Protocol does not apply to single-use storage devices and storage devices that are not coupled with power conversion systems, nor does it address safety, security, or operations and maintenance of ESSs, or provide any pass/fail criteria.

Ion-ion collisions and ion storage rings

International Nuclear Information System (INIS)

Mowat, J.R.

1988-01-01

Improved understanding of fundamental ion-ion interactions is expected to emerge from research carried out with ion storage rings. In this short survey the significant advantages and unique features that make stored ions useful targets for collision experiments are reviewed and discussed. It is pointed out that improvements to existing ion-ion experiments, as well as qualitatively new experiments, should occur over the next few years as ion storage rings become available for atomic physics. Some new experiments are suggested which are difficult if not impossible with present-day technology, but which seem feasible at storage rings facilities. (orig.)

Compacted spent-fuel storage--designs and problems

International Nuclear Information System (INIS)

Rubinstein, H.J.; Gilcrest, J.D.; Kendall, W.R.

1979-01-01

Typical rack designs, licensing, contracting methods, installation and operational problems are described. Due to the lack of reprocessing and independent fuel storage facilities, new plants built in the United States will continue to install high-density spent-fuel storage racks. As to the rack designs, the most significant feature is the introduction of freestanding rack designs. The trends in spent-fuel storage appear to be toward the use of high-density racks, either with or without absorber, for all plants in the design, construction, or operation phase; the use of freestanding rack designs; and the separation of engineering and fabrication during procurement

Flywheel energy storage workshop

Energy Technology Data Exchange (ETDEWEB)

O`Kain, D.; Carmack, J. [comps.

1995-12-31

Since the November 1993 Flywheel Workshop, there has been a major surge of interest in Flywheel Energy Storage. Numerous flywheel programs have been funded by the Advanced Research Projects Agency (ARPA), by the Department of Energy (DOE) through the Hybrid Vehicle Program, and by private investment. Several new prototype systems have been built and are being tested. The operational performance characteristics of flywheel energy storage are being recognized as attractive for a number of potential applications. Programs are underway to develop flywheels for cars, buses, boats, trains, satellites, and for electric utility applications such as power quality, uninterruptible power supplies, and load leveling. With the tremendous amount of flywheel activity during the last two years, this workshop should again provide an excellent opportunity for presentation of new information. This workshop is jointly sponsored by ARPA and DOE to provide a review of the status of current flywheel programs and to provide a forum for presentation of new flywheel technology. Technology areas of interest include flywheel applications, flywheel systems, design, materials, fabrication, assembly, safety & containment, ball bearings, magnetic bearings, motor/generators, power electronics, mounting systems, test procedures, and systems integration. Information from the workshop will help guide ARPA & DOE planning for future flywheel programs. This document is comprised of detailed viewgraphs.

Waste Encapsulation and Storage Facility (WESF) Waste Analysis Plan

International Nuclear Information System (INIS)

SIMMONS, F.M.

2000-01-01

The purpose of this waste analysis plan (WAP) is to document waste analysis activities associated with the Waste Encapsulation and Storage Facility (WESF) to comply with Washington Administrative Code (WAC) 173-303-300(1), (2), (3), (4), (5), and (6). WESF is an interim status other storage-miscellaneous storage unit. WESF stores mixed waste consisting of radioactive cesium and strontium salts. WESF is located in the 200 East Area on the Hanford Facility. Because dangerous waste does not include source, special nuclear, and by-product material components of mixed waste, radionuclides are not within the scope of this documentation. The information on radionuclides is provided only for general knowledge

Thermochemical Heat Storage: from Reaction Storage Density to System Storage Density

NARCIS (Netherlands)

Jong, A.J. de; Vliet, L.D. van; Hoegaerts, C.L.G.; Roelands, C.P.M.; Cuypers, R.

2016-01-01

Long-term and compact storage of solar energy is crucial for the eventual transition to a 100% renewable energy economy. For this, thermochemical materials provide a promising solution. The compactness of a long-term storage system is determined by the thermochemical reaction, operating conditions,

Low temperature thermal energy storage: a state-of-the-art survey

Energy Technology Data Exchange (ETDEWEB)

Baylin, F.

1979-07-01

The preliminary version of an analysis of activities in research, development, and demonstration of low temperature thermal energy storage (TES) technologies having applications in renewable energy systems is presented. Three major categories of thermal storage devices are considered: sensible heat; phase change materials (PCM); and reversible thermochemical reactions. Both short-term and annual thermal energy storage technologies based on prinicples of sensible heat are discussed. Storage media considered are water, earth, and rocks. Annual storage technologies include solar ponds, aquifers, and large tanks or beds of water, earth, or rocks. PCM storage devices considered employ salt hydrates and organic compounds. The sole application of reversible chemical reactions outlined is for the chemical heat pump. All program processes from basic research through commercialization efforts are investigated. Nongovernment-funded industrial programs and foreign efforts are outlined as well. Data describing low temperature TES activities are presented also as project descriptions. Projects for all these programs are grouped into seven categories: short-term sensible heat storage; annual sensible heat storage; PCM storage; heat transfer and exchange; industrial waste heat recovery and storage; reversible chemical reaction storage; and models, economic analyses, and support studies. Summary information about yearly funding and brief descriptions of project goals and accomplishments are included.

STP-ECRTS - THERMAL AND GAS ANALYSES FOR SLUDGE TRANSPORT AND STORAGE CONTAINER (STSC) STORAGE AT T PLANT

Energy Technology Data Exchange (ETDEWEB)

CROWE RD; APTHORPE R; LEE SJ; PLYS MG

2010-04-29

The Sludge Treatment Project (STP) is responsible for the disposition of sludge contained in the six engineered containers and Settler tank within the 105-K West (KW) Basin. The STP is retrieving and transferring sludge from the Settler tank into engineered container SCS-CON-230. Then, the STP will retrieve and transfer sludge from the six engineered containers in the KW Basin directly into a Sludge Transport and Storage Containers (STSC) contained in a Sludge Transport System (STS) cask. The STSC/STS cask will be transported to T Plant for interim storage of the STSC. The STS cask will be loaded with an empty STSC and returned to the KW Basin for loading of additional sludge for transportation and interim storage at T Plant. CH2MHILL Plateau Remediation Company (CHPRC) contracted with Fauske & Associates, LLC (FAI) to perform thermal and gas generation analyses for interim storage of STP sludge in the Sludge Transport and Storage Container (STSCs) at T Plant. The sludge types considered are settler sludge and sludge originating from the floor of the KW Basin and stored in containers 210 and 220, which are bounding compositions. The conditions specified by CHPRC for analysis are provided in Section 5. The FAI report (FAI/10-83, Thermal and Gas Analyses for a Sludge Transport and Storage Container (STSC) at T Plant) (refer to Attachment 1) documents the analyses. The process considered was passive, interim storage of sludge in various cells at T Plant. The FATE{trademark} code is used for the calculation. The results are shown in terms of the peak sludge temperature and hydrogen concentrations in the STSC and the T Plant cell. In particular, the concerns addressed were the thermal stability of the sludge and the potential for flammable gas mixtures. This work was performed with preliminary design information and a preliminary software configuration.

AnalyzeThis: An Analysis Workflow-Aware Storage System

Energy Technology Data Exchange (ETDEWEB)

Sim, Hyogi [ORNL; Kim, Youngjae [ORNL; Vazhkudai, Sudharshan S [ORNL; Tiwari, Devesh [ORNL; Anwar, Ali [Virginia Tech, Blacksburg, VA; Butt, Ali R [Virginia Tech, Blacksburg, VA; Ramakrishnan, Lavanya [Lawrence Berkeley National Laboratory (LBNL)

2015-01-01

The need for novel data analysis is urgent in the face of a data deluge from modern applications. Traditional approaches to data analysis incur significant data movement costs, moving data back and forth between the storage system and the processor. Emerging Active Flash devices enable processing on the flash, where the data already resides. An array of such Active Flash devices allows us to revisit how analysis workflows interact with storage systems. By seamlessly blending together the flash storage and data analysis, we create an analysis workflow-aware storage system, AnalyzeThis. Our guiding principle is that analysis-awareness be deeply ingrained in each and every layer of the storage, elevating data analyses as first-class citizens, and transforming AnalyzeThis into a potent analytics-aware appliance. We implement the AnalyzeThis storage system atop an emulation platform of the Active Flash array. Our results indicate that AnalyzeThis is viable, expediting workflow execution and minimizing data movement.

An Extended VIKOR-Based Approach for Pumped Hydro Energy Storage Plant Site Selection with Heterogeneous Information

Directory of Open Access Journals (Sweden)

Yunna Wu

2017-08-01

Full Text Available The selection of a desirable site for constructing a pumped hydro energy storage plant (PHESP plays a vital important role in the whole life cycle. However, little research has been done on the site selection of PHESP, which affects the rapid development of PHESP. Therefore, this paper aims to select the most ideal PHESP site from numerous candidate alternatives using the multi-criteria decision-making (MCDM technique. Firstly, a comprehensive evaluation criteria system is established for the first time. Then, considering quantitative and qualitative criteria coexist in this system, multiple types of representations, including crisp numerical values (CNVs, triangular intuitionistic fuzzy numbers (TIFNs, and 2-dimension uncertain linguistic variables (2DULVs, are employed to deal with heterogeneous criteria information. To determine the weight of criteria and fully take the preference of the decision makers (DMs into account, the analytic hierarchy process (AHP method is applied for criteria weighting. After that, an extended Vlsekriterijumska Optimizacija I Kompromisno Resenje (VIKOR method is utilized to provide compromise solutions for the PHESP site considering such heterogeneous information. At last, the proposed model is then applied in a case study of Zhejiang province, China to illustrate its practicality and efficiency. The result shows the Changlongshan should be selected as the optimal PHESP.

Remote Sensing Insights into Storage Capacities among Plains Village Horticulturalists

Science.gov (United States)

Wiewel, Adam S.

Maize was a fundamental component of the diet and economy of Middle Missouri Plains Village groups, sedentary farmers with settlements along the Missouri River during the last millennia. More than a century of study has contributed to our understanding of agricultural production among these peoples, but little effort has been made to consider temporal variation in production. Such an understanding is crucial to examining changes that occurred before and after the arrival of colonists and their trade goods in the seventeenth century. Plains archaeologists have suggested that the storage capacity of Middle Missouri villages increased during the sixteenth through the eighteenth centuries. In fact, the number and size of subterranean storage pits, ubiquitous features within most settlements, are thought to have grown during these centuries, which reflects greater agricultural production. To further examine changes in production and storage capacity during this centuries-long period, I combine information from historical documents, excavations, and geophysical investigations. At Huff Village, a fifteenth-century community, excavations and magnetic gradiometry surveys reveal the size and distribution of storage pits. Their number and average volume suggest the villagers grew immense amounts of food and contributed to widespread intertribal trade. Furthermore, storage pit excavation data from 20 regional sites, dating from the thirteenth to the nineteenth century, indicate pit volumes increased through the seventeenth century. A sharp decrease subsequently occurred during the eighteenth century due to epidemic disease. However, mean pit volumes were significantly larger during the nineteenth century, evidence of the resilience of Mandans, Hidatsas, and Arikaras and the continued significance of maize. In fact, historical documents and remote sensing data suggest the Mandans and Arikaras, successive occupants of an earthlodge village near the American Fur Company's Fort

Proactive replica checking to assure reliability of data in cloud storage with minimum replication

Science.gov (United States)

Murarka, Damini; Maheswari, G. Uma

2017-11-01

The two major issues for cloud storage systems are data reliability and storage costs. For data reliability protection, multi-replica replication strategy which is used mostly in current clouds acquires huge storage consumption, leading to a large storage cost for applications within the loud specifically. This paper presents a cost-efficient data reliability mechanism named PRCR to cut back the cloud storage consumption. PRCR ensures data reliability of large cloud information with the replication that might conjointly function as a price effective benchmark for replication. The duplication shows that when resembled to the standard three-replica approach, PRCR will scale back to consume only a simple fraction of the cloud storage from one-third of the storage, thence considerably minimizing the cloud storage price.

Data storage accounting and verification in LHC experiments

CERN Document Server

Ratnikova ,Natalia

2012-01-01

All major experiments at Large Hadron Collider (LHC) need to measure real storage usage at the Grid sites. This information is equally important for the resource management, planning, and operations. To verify consistency of the central catalogs, experiments are asking sites to provide full list of files they have on storage, including size, checksum, and other file attributes. Such storage dumps provided at regular intervals give a realistic view of the storage resource usage by the experiments. Regular monitoring of the space usage and data verification serve as additional internal checks of the system integrity and performance. Both the importance and the complexity of these tasks increase with the constant growth of the total data volumes during the active data taking period at the LHC. Developed common solutions help to reduce the maintenance costs both at the large Tier-1 facilities supporting multiple virtual organizations, and at the small sites that often lack manpower. We discuss requirements...

Alternatives for water basin spent fuel storage using pin storage

International Nuclear Information System (INIS)

Viebrock, J.M.; Carlson, R.W.

1979-09-01

The densest tolerable form for storing spent nuclear fuel is storage of only the fuel rods. This eliminates the space between the fuel rods and frees the hardware to be treated as non-fuel waste. The storage density can be as much as 1.07 MTU/ft 2 when racks are used that just satisfy the criticality and thermal limitations. One of the major advantages of pin storage is that it is compatible with existing racks; however, this reduces the storage density to 0.69 MTU/ft 2 . Even this is a substantial increase over the 0.39 MTU/ft 2 that is achievable with current high capacity stainless steel racks which have been selected as the bases for comparison. Disassembly requires extensive operation on the fuel assembly to remove the upper end fitting and to extract the fuel rods from the assembly skeleton. These operations will be performed with the aid of an elevator to raise the assembly where each fuel rod is grappled. Lowering the elevator will free the fuel rod for transfer to the storage canister. A storage savings of $1510 per MTU can be realized if the pin storage concept is incorporated at a new away-from-reactor facility. The storage cost ranges from $3340 to $7820 per MTU of fuel stored with the lower cost applying to storage at an existing away-from-reactor storage facility and the higher cost applying to at-reactor storage

Energy Policy Act of 2005 and Underground Storage Tanks (USTs)

Science.gov (United States)

The Energy Policy Act of 2005 significantly affected federal and state underground storage tank programs, required major changes to the programs, and is aimed at reducing underground storage tank releases to our environment.

At-reactor storage of spent fuel for life-of-plant

International Nuclear Information System (INIS)

Fuierer, A.A.

1990-01-01

The management of commercial spent fuel is a fairly broad topic beginning with the discharge from a reactor, its storage on-site, its transport from the reactor site to a U.S. Department of Energy (DOE) facility, and its ultimate disposal in a geologic repository. This paper discusses spent-fuel management in the at-reactor phase. There are two basic methods for at-reactor storage of spent fuel. The first is wet storage in a pool, and the second is dry storage external to the plant in some form of cask or vault. Spent-fuel consolidation will impact the utility and the DOE waste system. Some of these impacts have a positive effect and some have a negative effect, and each will vary somewhat for each utility. Spent-fuel consolidation and life-of-plant storage will be an increased burden to utilities but will likely result in significant cost savings to the overall waste management system and by proper integration can result in significant institutional benefits

Monitoring small reservoirs' storage with satellite remote sensing in inaccessible areas

Directory of Open Access Journals (Sweden)

N. Avisse

2017-12-01

Full Text Available In river basins with water storage facilities, the availability of regularly updated information on reservoir level and capacity is of paramount importance for the effective management of those systems. However, for the vast majority of reservoirs around the world, storage levels are either not measured or not readily available due to financial, political, or legal considerations. This paper proposes a novel approach using Landsat imagery and digital elevation models (DEMs to retrieve information on storage variations in any inaccessible region. Unlike existing approaches, the method does not require any in situ measurement and is appropriate for monitoring small, and often undocumented, irrigation reservoirs. It consists of three recovery steps: (i a 2-D dynamic classification of Landsat spectral band information to quantify the surface area of water, (ii a statistical correction of DEM data to characterize the topography of each reservoir, and (iii a 3-D reconstruction algorithm to correct for clouds and Landsat 7 Scan Line Corrector failure. The method is applied to quantify reservoir storage in the Yarmouk basin in southern Syria, where ground monitoring is impeded by the ongoing civil war. It is validated against available in situ measurements in neighbouring Jordanian reservoirs. Coefficients of determination range from 0.69 to 0.84, and the normalized root-mean-square error from 10 to 16 % for storage estimations on six Jordanian reservoirs with maximal water surface areas ranging from 0.59 to 3.79 km2.

Volume Holographic Storage of Digital Data Implemented in Photorefractive Media

Science.gov (United States)

Heanue, John Frederick

A holographic data storage system is fundamentally different from conventional storage devices. Information is recorded in a volume, rather than on a two-dimensional surface. Data is transferred in parallel, on a page-by -page basis, rather than serially. These properties, combined with a limited need for mechanical motion, lead to the potential for a storage system with high capacity, fast transfer rate, and short access time. The majority of previous volume holographic storage experiments have involved direct storage and retrieval of pictorial information. Success in the development of a practical holographic storage device requires an understanding of the performance capabilities of a digital system. This thesis presents a number of contributions toward this goal. A description of light diffraction from volume gratings is given. The results are used as the basis for a theoretical and numerical analysis of interpage crosstalk in both angular and wavelength multiplexed holographic storage. An analysis of photorefractive grating formation in photovoltaic media such as lithium niobate is presented along with steady-state expressions for the space-charge field in thermal fixing. Thermal fixing by room temperature recording followed by ion compensation at elevated temperatures is compared to simultaneous recording and compensation at high temperature. In particular, the tradeoff between diffraction efficiency and incomplete Bragg matching is evaluated. An experimental investigation of orthogonal phase code multiplexing is described. Two unique capabilities, the ability to perform arithmetic operations on stored data pages optically, rather than electronically, and encrypted data storage, are demonstrated. A comparison of digital signal representations, or channel codes, is carried out. The codes are compared in terms of bit-error rate performance at constant capacity. A well-known one-dimensional digital detection technique, maximum likelihood sequence estimation, is

Efficient proof of ownership for cloud storage systems

Science.gov (United States)

Zhong, Weiwei; Liu, Zhusong

2017-08-01

Cloud storage system through the deduplication technology to save disk space and bandwidth, but the use of this technology has appeared targeted security attacks: the attacker can deceive the server to obtain ownership of the file by get the hash value of original file. In order to solve the above security problems and the different security requirements of the files in the cloud storage system, an efficient and information-theoretical secure proof of ownership sceme is proposed to support the file rating. Through the K-means algorithm to implement file rating, and use random seed technology and pre-calculation method to achieve safe and efficient proof of ownership scheme. Finally, the scheme is information-theoretical secure, and achieve better performance in the most sensitive areas of client-side I/O and computation.

Safety Aspects of Long Term Spent Fuel Dry Storage

International Nuclear Information System (INIS)

Botsch, Wolfgang; Smalian, S.; Hinterding, P.; Drotleff, H.; Voelzke, H.; Wolff, D.; Kasparek, E.

2014-01-01

As a consequence of the lack of a final repository for spent nuclear fuel (SF) and high level waste (HLW), long term interim storage of SF and HLW will be necessary. As with the storage of all radioactive materials, the long term storage of SF and HLW must conform to safety requirements. Safety aspects such as safe enclosure of radioactive materials, safe removal of decay heat, sub-criticality and avoidance of unnecessary radiation exposure must be achieved throughout the complete storage period. The implementation of these safety requirements can be achieved by dry storage of SF and HLW in casks as well as in other systems such as dry vault storage systems or spent fuel pools, where the latter is neither a dry nor a passive system. After the events of Fukushima, the advantages of passively and inherently safe dry storage systems have become more obvious. In Germany, dry storage of SF in casks fulfils both transport and storage requirements. Mostly, storage facilities are designed as concrete buildings above the ground; one storage facility has also been built as a rock tunnel. In all these facilities the safe enclosure of radioactive materials in dry storage casks is achieved by a double-lid sealing system with surveillance of the sealing system. The safe removal of decay heat is ensured by the design of the storage containers and the storage facility, which also secures to reduce the radiation exposure to acceptable levels. TUV and BAM, who work as independent experts for the competent authorities, inform about spent fuel management and issues concerning dry storage of spent nuclear fuel, based on their long experience in these fields. All relevant safety issues such as safe enclosure, shielding, removal of decay heat and sub-criticality are checked and validated with state-of-the-art methods and computer codes before the license approval. In our presentation we discuss which of these aspects need to be examined closer for a long term interim storage. It is shown

Platelet concentrates for transfusion-metabolic and storage aspects.

Science.gov (United States)

Farrugia, A

1994-01-01

Transfusion of platelets concentrated from donated blood is an established therapeutic modality in clinical medicine. Over the past 25 years much effort has gone into optimising the conditions for the collection, preparation and storage of platelets for transfusion. Despite significant advances, platelet production is still a costly process requiring a dedicated environment and the use of specially formulated plastic storage containers. A progressive lesion over storage limits the shelf life and the availability of donated platelets, while the need to store platelets in the donor's autologous plasma also results in a loss of valuable fresh plasma for fractionation. Recent studies have addressed the issues of platelet quality and plasma economy by examining the possibility of storing platelets in a synthetic medium. Platelets stored in a variety of crystalloid solutions have been shown to retain in vitro and in vivo properties equivalent or superior to platelets stored in autologous donor plasma. Some additional insight has been gained on the metabolic patterns of stored platelets. In particular, studies have shown that, under these conditions, platelets are unable to oxidise dextrose to any significant extent, and that dextrose is invariably broken down to lactate, irrespective of the oxygen tensions in the platelet's environment. This in turn leads to the metabolic lesion of platelet storage, whereby low pH results in loss of platelet viability. Platelets stored in synthetic dextrose-free media are capable of maintaining aerobic ATP generation, and acetate-a component of many media studied-has been shown to be metabolised by platelets. Similarly, platelets prepared from blood collected into a dextrose-free anticoagulant have satisfactory properties both when suspended in autologous plasma or in a dextrose-free synthetic medium. The requirements for storage in special, high gas-permeable, containers, and for constant agitation during storage, were both found to be

Final version dry cask storage study

International Nuclear Information System (INIS)

1989-02-01

This report was prepared in response to Section 5064 of the Nuclear Waste Policy Amendments Act of 1987 (the Amendments Act--Public Law 100-203), which directs the Secretary of Energy to conduct a study of the use of dry-cask-storage technology for storing spent fuel at the sites of civilian nuclear reactors until a geologic repository is available. In conducting this study, whose results are being reported to the Congress, the Secretary was to consider such factors as costs, effects on human health and the environment, and the extent to which the Nuclear Waste Fund can and should be used to provide funds for at-reactor storage. In addition, the Secretary was to consult with the Nuclear Regulatory Commission (NRC), include NRC comments in the report, and solicit the views of State and local governments and the public. The study performed in response to these requirements was based largely on data published by the DOE or the NRC or included in documents issued by the DOE. Among the DOE documents are the 1987 MRS proposal to the Congress and a subsequent report, prepared to supply the Congress with additional information on the MRS facility. Because in evaluating dry storage at reactor sites it is necessary to take into account other options for meeting storage needs, this study covered all forms of at-reactor storage. 107 refs., 15 figs., 10 tabs

Release of tritium from fuel and collection for storage

International Nuclear Information System (INIS)

Burger, L.L.; Trevorrow, L.E.

1976-04-01

Recent work is reviewed on the technology that has been suggested as applicable to collection and storage of tritium in anticipation of the necessity of that course of action. Collection technology and procedures must be adapted to the tritium-bearing effluent and to the facility from which it emerges. Therefore, this discussion of tritium collection technology includes some information on the processes from which release is expected to occur, the amounts, the nature of the effluent media, and the form in which tritium appears. Recent work on collection and storage concepts has explored, both by experimentation and by feasibility analyses, the operations generally aimed at producing recycle, collection, or storage of tritium from these streams. Storage concepts aimed specifically at tritium involve plans to store volumes ranging from that of the entire effluent stream to only that of a small volume of a concentrate. Decisions between storage of unconcentrated streams and storage of concentrates are expected to be made largely by weighing the cost of storage space against the cost of concentration. The storage of tritium concentrate requires the selection of a form of tritium possessing physical and chemical properties appropriate for the expected storage conditions. This selection of an appropriate storage form has occupied a major portion of recent work concerned with tritium storage concepts. In summary, within the context of present regulations and expected amounts of waste tritium; this waste can be disposed of by dilution and dispersal to the environment. In the future, however, more restrictive regulations might be introduced that could be satisfied only by some collection and storage operations. Technology for this practice is not now available, and the present discussion reviews recent activities devoted to its development

Feasibility study and economic analysis of pumped hydro storage and battery storage for a renewable energy powered island

International Nuclear Information System (INIS)

Ma, Tao; Yang, Hongxing; Lu, Lin

2014-01-01

Highlights: • Batteries and pumped hydro storage schemes are examined. • Sizing procedure for each option is investigated in detail. • The two schemes are compared in terms of life cycle cost and technical viability. • Sensitivity analyses are conducted on five key input parameters. - Abstract: This study examined and compared two energy storage technologies, i.e. batteries and pumped hydro storage (PHS), for the renewable energy powered microgrid power supply system on a remote island in Hong Kong. The problems of energy storage for off-grid renewable energy were analyzed. The sizing methods and economic models were developed, and finally applied in the real project (case study). The results provide the most suitable energy storage scheme for local decision-makers. The two storage schemes were further divided into 4 options. Accordingly, the life-cycle costs (LCC), levelized costs for the renewable energy storage system (LCRES) and the LCC ratios between all options were calculated and compared. It was found that the employment of conventional battery (Option 2) had a higher LCC value than the advanced deep cycle battery (Option 1), indicating that using deep cycle batteries is more suitable for a standalone renewable power supply system. The pumped storage combined with battery bank option (Option 3) had only 55% LCC of that of Option 1, making this combined option more cost-competitive than the sole battery option. The economic benefit of pumped storage is even more significant in the case of purely pumped storage with a hydraulic controller (Option 4), with the lowest LCC among all options at 29–48% of Option 1. Sensitivity analysis demonstrates that PHS is even more cost competitive by controlling some adjustments such as increasing energy storage capacity and days of autonomy. Therefore, the renewable energy system coupled with pumped storage presents technically feasible opportunities and practical potential for continuous power supply in remote

Materials compatibility information data bank

International Nuclear Information System (INIS)

Mead, K.E.

1977-01-01

A major concern in the design of weapons systems is the compatibility of the materials used with each other and with the enclosed environment. Usually these systems require long term storage with a high reliability for proper function at the end of this storage period. Materials selection is then based on both past experience and laboratory accelerated aging experiments to assure this long term reliability. To assist in the task of materials selection a computerized materials compatibility data bank is being established. This data bank will provide a source of annotated information and references to personnel and documents for both the designer and materials engineer to draw on for guidance in materials selection. The data bank storage and information retrieval philosophy will be discussed and procedures for information gathering outlined. Examples of data entries and search routines will be presented to demonstrate the usefulness and versatility of the proposed system

Buffer thermal energy storage for a solar Brayton engine

Science.gov (United States)

Strumpf, H. J.; Barr, K. P.

1981-01-01

A study has been completed on the application of latent-heat buffer thermal energy storage to a point-focusing solar receiver equipped with an air Brayton engine. To aid in the study, a computer program was written for complete transient/stead-state Brayton cycle performance. The results indicated that thermal storage can afford a significant decrease in the number of engine shutdowns as compared to operating without thermal storage. However, the number of shutdowns does not continuously decrease as the storage material weight increases. In fact, there appears to be an optimum weight for minimizing the number of shutdowns.

Multiplexed optical data storage and vectorial ray tracing

Directory of Open Access Journals (Sweden)

Foreman M.R.

2010-06-01

Full Text Available With the motivation of creating a terabyte-sized optical disk, a novel imaging technique is implemented. This technique merges two existing technologies: confocal microscopy and Mueller matrix imaging. Mueller matrix images from a high numerical space are obtained. The acquisition of these images makes the exploration of polarisation properties in a sample possible. The particular case of optical data storage is used as an example in this presentation. Since we encode information into asymmetric datapits (see Figure 1, the study of the polarisation of the scattered light can then be used to recover the orientation of the pit. It is thus possible to multiplex information by changing the angle of the mark. The storage capacity in the system is hence limited by the number of distinct angles that the optical system can resolve. This presentation thus answers the question; what is the current storage capacity of a polarisation sensitive optical disk? After a brief introduction to polarisation, the decoding method and experimental results are presented so as to provide an answer to this question. With the aim of understanding high NA focusing, an introduction to vectorial ray tracing is then given.

Public storage for the Open Science Grid

International Nuclear Information System (INIS)

Levshina, T; Guru, A

2014-01-01

The Open Science Grid infrastructure doesn't provide efficient means to manage public storage offered by participating sites. A Virtual Organization that relies on opportunistic storage has difficulties finding appropriate storage, verifying its availability, and monitoring its utilization. The involvement of the production manager, site administrators and VO support personnel is required to allocate or rescind storage space. One of the main requirements for Public Storage implementation is that it should use SRM or GridFTP protocols to access the Storage Elements provided by the OSG Sites and not put any additional burden on sites. By policy, no new services related to Public Storage can be installed and run on OSG sites. Opportunistic users also have difficulties in accessing the OSG Storage Elements during the execution of jobs. A typical users' data management workflow includes pre-staging common data on sites before a job's execution, then storing for a subsequent download to a local institution the output data produced by a job on a worker node. When the amount of data is significant, the only means to temporarily store the data is to upload it to one of the Storage Elements. In order to do that, a user's job should be aware of the storage location, availability, and free space. After a successful data upload, users must somehow keep track of the data's location for future access. In this presentation we propose solutions for storage management and data handling issues in the OSG. We are investigating the feasibility of using the integrated Rule-Oriented Data System developed at RENCI as a front-end service to the OSG SEs. The current architecture, state of deployment and performance test results will be discussed. We will also provide examples of current usage of the system by beta-users.

Public storage for the Open Science Grid

Science.gov (United States)

Levshina, T.; Guru, A.

2014-06-01

The Open Science Grid infrastructure doesn't provide efficient means to manage public storage offered by participating sites. A Virtual Organization that relies on opportunistic storage has difficulties finding appropriate storage, verifying its availability, and monitoring its utilization. The involvement of the production manager, site administrators and VO support personnel is required to allocate or rescind storage space. One of the main requirements for Public Storage implementation is that it should use SRM or GridFTP protocols to access the Storage Elements provided by the OSG Sites and not put any additional burden on sites. By policy, no new services related to Public Storage can be installed and run on OSG sites. Opportunistic users also have difficulties in accessing the OSG Storage Elements during the execution of jobs. A typical users' data management workflow includes pre-staging common data on sites before a job's execution, then storing for a subsequent download to a local institution the output data produced by a job on a worker node. When the amount of data is significant, the only means to temporarily store the data is to upload it to one of the Storage Elements. In order to do that, a user's job should be aware of the storage location, availability, and free space. After a successful data upload, users must somehow keep track of the data's location for future access. In this presentation we propose solutions for storage management and data handling issues in the OSG. We are investigating the feasibility of using the integrated Rule-Oriented Data System developed at RENCI as a front-end service to the OSG SEs. The current architecture, state of deployment and performance test results will be discussed. We will also provide examples of current usage of the system by beta-users.

Retrievable surface storage: interim storage of solidified high-level waste

International Nuclear Information System (INIS)

LaRiviere, J.R.; Nelson, D.C.

1976-01-01

Studies have been conducted on retrievable-surface-storage concepts for the interim storage of solidified high-level wastes. These studies have been reviewed by the Panel on Engineered Storage, convened by the Committee on Radioactive Waste Management of the National Research Council-National Academy of Sciences. The Panel has concluded that ''retrievable surface storage is an acceptable interim stage in a comprehensive system for managing high-level radioactive wastes.'' The scaled storage cask concept, which was recommended by the Panel on Engineered Storage, consists of placing a canister of waste inside a carbon-steel cask, which in turn is placed inside a thick concrete cylinder. The waste is cooled by natural convection air flow through an annulus between the cask and the inner wall of the concrete cylinder. The complete assembly is placed above ground in an outdoor storage area

Optimal design and application of a compound cold storage system combining seasonal ice storage and chilled water storage

NARCIS (Netherlands)

Yan, C.; Shi, W.; Li, X.; Zhao, Y.

2016-01-01

Seasonal cold storage using natural cold sources for cooling is a sustainable cooling technique. However, this technique suffers from limitations such as large storage space and poor reliability. Combining seasonal storage with short-term storage might be a promising solution while it is not

A Network-Attached Storage System Supporting Guaranteed QoS

Institute of Scientific and Technical Information of China (English)

KONG Hua-feng; YU Sheng-sheng; LU Hong-wei

2005-01-01

We propose a network-attached storage system that can support guaranteed Quality of Service (QoS), called POPNet Storage. The special policy of date access and disk scheduling is enable users to access files quickly and directly with guaranteed QoS in the POPNet Storage. The POPNet Storage implements a measurement-based admission control algorithm (PSMBAC) to determine whether to admit a new data access request stream and admit as many requests as possible while meeting the QoS guarantees to its clients. The data reconstruction algorithms in the POPNet Storage also put more emphasis on data availability and guaranteed QoS, thus it is designed to complete the data recovery as soon as possible and at the same time provide the guaranteed QoS for high-priority data access. The experiment results show that the POPNet Storage can provide more significant performance, reliability, and guaranteed QoS than conventional storage systems.

Data storage accounting and verification at LHC experiments

Energy Technology Data Exchange (ETDEWEB)

Huang, C. H. [Fermilab; Lanciotti, E. [CERN; Magini, N. [CERN; Ratnikova, N. [Moscow, ITEP; Sanchez-Hernandez, A. [CINVESTAV, IPN; Serfon, C. [Munich U.; Wildish, T. [Princeton U.; Zhang, X. [Beijing, Inst. High Energy Phys.

2012-01-01

All major experiments at the Large Hadron Collider (LHC) need to measure real storage usage at the Grid sites. This information is equally important for resource management, planning, and operations. To verify the consistency of central catalogs, experiments are asking sites to provide a full list of the files they have on storage, including size, checksum, and other file attributes. Such storage dumps, provided at regular intervals, give a realistic view of the storage resource usage by the experiments. Regular monitoring of the space usage and data verification serve as additional internal checks of the system integrity and performance. Both the importance and the complexity of these tasks increase with the constant growth of the total data volumes during the active data taking period at the LHC. The use of common solutions helps to reduce the maintenance costs, both at the large Tier1 facilities supporting multiple virtual organizations and at the small sites that often lack manpower. We discuss requirements and solutions to the common tasks of data storage accounting and verification, and present experiment-specific strategies and implementations used within the LHC experiments according to their computing models.

Energy Conversion and Storage Requirements for Hybrid Electric Aircraft

Science.gov (United States)

Misra, Ajay

2016-01-01

Among various options for reducing greenhouse gases in future large commercial aircraft, hybrid electric option holds significant promise. In the hybrid electric aircraft concept, gas turbine engine is used in combination with an energy storage system to drive the fan that propels the aircraft, with gas turbine engine being used for certain segments of the flight cycle and energy storage system being used for other segments. The paper will provide an overview of various energy conversion and storage options for hybrid electric aircraft. Such options may include fuel cells, batteries, super capacitors, multifunctional structures with energy storage capability, thermoelectric, thermionic or a combination of any of these options. The energy conversion and storage requirements for hybrid electric aircraft will be presented. The role of materials in energy conversion and storage systems for hybrid electric aircraft will be discussed.

Spent-fuel-storage requirements: an update of DOE/RL-82-1

International Nuclear Information System (INIS)

1983-01-01

Spent fuel storage requirements as projected through the year 2000 for US light water reactor (LWR) nuclear power plants were calculated using information supplied by the utilities reflecting plant status as of September 30, 1982. Projections through the year 2000 combined fuel discharge projections of the utilities with the assumed discharges of typical reactors required to meet the nuclear capacity of 132 gigawatts electrical (GWe) projected by the Energy Information Administration (EIA) for the year 2000. Three cases were developed and are summarized. A reference case, or maximum at-reactor (AR) capacity case, assumes that all reactor storage pools are increased to their maximum capacities, as estimated by the utilities, for spent fuel storage utilizing currently licensed technologies. Rod consolidation and dry storage technologies were not considered. The reference case assumes no transshipments between pools except as currently licensed by the Nuclear Regulatory Commission (NRC). This case identifies an initial requirement for 13 metric tons uranium (MTU) of additional storage in 1984, and a cumulative requirement for 13,090 MTU additional storage in the year 2000. The reference case is bounded by two alternative cases. One, a current capacity case, assumes that only those pool storage capacity increases currently planned by the operating utilities will occur. The second, or maximum capacity with transshipment case, assumes maximum development of pool storage capacity as described above and also assumes no constraints on transshipment of spent fuel among pools of reactors of like type (BWR) within a given utility. In all cases, a full core discharge capability is assumed to be maintained for each reactor, except that only one FCR is maintained when two reactors share a common pool. 1 figure, 12 tables

Potential mechanisms for corrosion and stress corrosion cracking failure of 3013 storage containers composed of 316 stainless steel

International Nuclear Information System (INIS)

Kolman, D.G.; Butt, D.P.

1998-01-01

The degradation of 316 stainless steel (SS) storage container materials is a potential problem for radioactive waste disposition. Container materials will be exposed to significant ionizing radiation, elevated temperatures, embrittling and/or alloying agents (e.g., gallium), chloride-containing compounds (as much as 20 wt% Cl or Cl - ), oxidizing compounds, and a limited quantity of moisture. Additionally, containers will contain welds that have heterogeneous composition due to solute segregation and that may retain significant residual stress. All of the above-listed environmental and material conditions have been shown to be deleterious to material integrity under certain conditions. Unfortunately, the precise conditions within each container and environment is unknown and may vary widely from container to container. Thus, no single test or set of tests will be able mimic the broad range of storage container conditions. Additionally, material behavior cannot be predicted because the synergistic effects of temperature, time, chloride, moisture, sensitization, weldments, salt formation, etc., have not been fully studied. The complexity and uncertainty of storage conditions precludes any detailed recommendations. This document attempts to detail selected previous studies and to suggest some general guidelines for storage of radioactive waste. Because of the voluminous research in this area, this review cannot be considered to be comprehensive. Readers are directed to references that contain detailed reviews of particular processes for more information. Note that the effect of gallium on the degradation of SS storage containers has been discussed elsewhere and will not be discussed here

Optimal scheduling for distribution network with redox flow battery storage

International Nuclear Information System (INIS)

Hosseina, Majid; Bathaee, Seyed Mohammad Taghi

2016-01-01

Highlights: • A novel method for optimal scheduling of storages in radial network is presented. • Peak shaving and load leveling are the main objectives. • Vanadium redox flow battery is considered as the energy storage unit. • Real data is used for simulation. - Abstract: There are many advantages to utilize storages in electric power system. Peak shaving, load leveling, load frequency control, integration of renewable, energy trading and spinning reserve are the most important of them. Batteries, especially redox flow batteries, are one of the appropriate storages for utilization in distribution network. This paper presents a novel, heuristic and practical method for optimal scheduling in distribution network with flow battery storage. This heuristic method is more suitable for scheduling and operation of distribution networks which require installation of storages. Peak shaving and load leveling is considered as the main objective in this paper. Several indices are presented in this paper for determine the place of storages and also scheduling for optimal use of energy in them. Simulations of this paper are based on real information of distribution network substation that located in Semnan, Iran.

Scaling up DNA data storage and random access retrieval

OpenAIRE

Gopalan, Parikshit; Ceze, Luis; Nguyen, Bichlien; Takahashi, Christopher; Newman, Sharon; Parker, Hsing-Yeh; Rashtchian, Cyrus; Seelig, Georg; Stewart, Kendall; Gupta, Gagan; Carlson, Robert; Mulligan, John; Carmean, Douglas; Yekhanin, Sergey; Makarychev, Konstantin

2017-01-01

Current storage technologies can no longer keep pace with exponentially growing amounts of data. Synthetic DNA offers an attractive alternative due to its potential information density of ~ 1018B/mm3, 107 times denser than magnetic tape, and potential durability of thousands of years. Recent advances in DNA data storage have highlighted technical challenges, in particular, coding and random access, but have stored only modest amounts of data in synthetic DNA. This paper demonstrates an end-to...

Method of storing the fuel storage pot in a fuel storage tank for away-from-reactor-storage

International Nuclear Information System (INIS)

Ishiguro, Jun-ichi.

1980-01-01

Purpose: To prevent the contact of sodium in the away-from-reactor-storage fuel storage tank with sodium in a fuel storage pool having radioactivity ana always retain clean state therein. Method: Sodium is filled in a container body of the away-from-reactor-storage fuel storage tank, and a conduit, a cycling pump, and cooling means are disposed to form a sodium coolant cycling loop. The fuel storage pool is so stored in the container body that the heat of the pool is projected from the liquid surface of the sodium in the container. Therefore, the sodium in the container is isolated from the sodium in the pool containing strong radioactivity to prevent contact of the former sodium from the latter sodium. (Sekiya, K.)

Using Hadoop as a grid storage element

International Nuclear Information System (INIS)

Bockelman, Brian

2009-01-01

Hadoop is an open-source data processing framework that includes a scalable, fault-tolerant distributed file system, HDFS. Although HDFS was designed to work in conjunction with Hadoop's job scheduler, we have re-purposed it to serve as a grid storage element by adding GridFTP and SRM servers. We have tested the system thoroughly in order to understand its scalability and fault tolerance. The turn-on of the Large Hadron Collider (LHC) in 2009 poses a significant data management and storage challenge; we have been working to introduce HDFS as a solution for data storage for one LHC experiment, the Compact Muon Solenoid (CMS).

Medical images storage using discrete cosine transform

International Nuclear Information System (INIS)

Arhouma, Ali M.; Ajaal, Tawfik; Marghani, Khaled

2010-01-01

The advances in technology during the last decades have made the use of digital images as one of the common things in everyday life. While the application of digital images in communicating information is very important, the cost of storing and transmitting images is much larger compared to storage and transmission of text. The main problem with all of the images was the fact that they take large size of memory space, large transmission bandwidth and long transmission time. Image data compression is needed to reduce the storage space,transmission bandwidth and transmission time. Medical image compression plays a key role as hospitals move towards filmless imaging and go completely digital. Image compression allows Picture Archiving and Communication Systems (PACS) to reduce the file size on their storage requirements while maintaining relevant diagnostic information. The reduced image file size yield reduced transmission times. Even as the capacity of storage media continues to increase, it is expected that the volume of uncompressed data produced by hospitals will exceed capacity of storage and drive up costs. This paper proposes a Discrete Cosine Transform (DCT) algorithm which can help to solve the image storage and transmission time problem in hospitals. Discrete cosine transform (DCT) has become the most popular technique for image compression over the past several years. One of the major reasons for its popularity is its selection as the standard for JPEG. DCTs are most commonly used for non-analytical applications such as image processing and digital signal-processing (DSP) applications such as video conferencing, fax systems, video disks, and high-definition television HDTV. They also can be used on a matrix of practically any dimension. The proposed (DCT) algorithm improves the performance of medical image compression while satisfying both the medical image quality, and the high compression ratio. Application of DCT coding algorithm to actual still images

Underground storage of imported water in the San Gorgonio Pass area, southern California

Science.gov (United States)

Bloyd, Richard M.

1971-01-01

The San Gorgonio Pass ground-water basin is divided into the Beaumont, Banning, Cabazon, San Timoteo, South Beaumont, Banning Bench, and Singleton storage units. The Beaumont storage unit, centrally located in the agency area, is the largest in volume of the storage units. Estimated long-term average annual precipitation in the San Gorgonio Pass Water Agency drainage area is 332,000 acre-feet, and estimated average annual recoverable water is 24,000 acre-feet, less than 10 percent of the total precipitation. Estimated average annual surface outflow is 1,700 acre-feet, and estimated average annual ground-water recharge is 22,000 acre-feet. Projecting tack to probable steady-state conditions, of the 22.000 acre-feet of recharge, 16,003 acre-feet per year became subsurface outflow into Coachella Valley, 6,000 acre-feet into the Redlands area, and 220 acre-feet into Potrero Canyon. After extensive development, estimated subsurface outflow from the area in 1967 was 6,000 acre-feet into the Redlands area, 220 acre-feet into Potrero Canyon, and 800 acre-feet into the fault systems south of the Banning storage unit, unwatered during construction of a tunnel. Subsurface outflow into Coachella Valley in 1967 is probably less than 50 percent of the steady-state flow. An anticipated 17,000 .acre-feet of water per year will be imported by 1980. Information developed in this study indicates it is technically feasible to store imported water in the eastern part of the Beaumont storage unit without causing waterlogging in the storage area and without losing any significant quantity of stored water.

Inductive line energy storage generator

Energy Technology Data Exchange (ETDEWEB)

Choi, P [Ecole Polytechnique, Palaiseau (France). Laboratoire de Physique des Milieux Ionises

1997-12-31

The inductive energy storage (IES) generator has long been considered to be the most efficient system for energy usage in large pulsed power system at the MA level. A number of parameters govern the efficiency of energy transfer between the storage capacitors and the load, and the level of current deliverable to the load. For high power system, the energy storage capacitors are arranged as a Marx generator. The primary constraints are the inductances in the various parts of the circuit, in particular, the upstream inductance between the Marx and the POS, and the downstream inductance between the POS and the load. This paper deals with the effect of replacing part of the upstream inductance with a transmission line and introduces the new concept of an inductive line for energy storage (ILES). Extensive parametric scans were carried out on circuit simulations to investigate the effect of this upstream transmission line. A model was developed to explain the operation of the ILES design based on the data obtained. Comparison with an existing IES generator shows that the ILES design offers a significant improvement in the maximum current and hence energy delivered to an inductive load. (author). 5 figs., 1 ref.

Spent fuel storage - dry storage options and issues

International Nuclear Information System (INIS)

Akins, M.J.

2007-01-01

The increase in the number of nuclear energy power generation facilities will require the ability to store the spent nuclear fuel for a long period until the host countries develop reprocessing or disposal options. Plants have storage pools which are closely associated with the operating units. These are excellent for short term storage, but require active maintenance and operations support which are not desirable for the long term. Over the past 25 years, dry storage options have been developed and implemented throughout the world. In recent years, protection against terrorist attack has become an increasing source of design objectives for these facilities, as well as the main nuclear plant. This paper explores the current design options of dry storage cask systems and examines some of the current design issues for above ground , in-ground, or below-ground storage of spent fuel in dry casks. (author)

Aquifer thermal energy storage reference manual: seasonal thermal energy storage program

Energy Technology Data Exchange (ETDEWEB)

Prater, L.S.

1980-01-01

This is the reference manual of the Seasonal Thermal Energy Storage (STES) Program, and is the primary document for the transfer of technical information of the STES Program. It has been issued in preliminary form and will be updated periodically to include more technical data and results of research. As the program progresses and new technical data become available, sections of the manual will be revised to incorporate these data. This primary document contains summaries of: the TRW, incorporated demonstration project at Behtel, Alaska, Dames and Moore demonstration project at Stony Brook, New York, and the University of Minnesota demonstration project at Minneapolis-St. Paul, Minnesota; the technical support programs including legal/institutional assessment; economic assessment; environmental assessment; field test facilities; a compendia of existing information; numerical simulation; and non-aquifer STES concepts. (LCL)

Thermal energy storage using chloride salts and their eutectics

International Nuclear Information System (INIS)

Myers, Philip D.; Goswami, D. Yogi

2016-01-01

Achieving the goals of the U.S. Department of Energy (DOE) Sunshot initiative requires (1) higher operating temperatures for concentrating solar power (CSP) plants to increase theoretical efficiency, and (2) effective thermal energy storage (TES) strategies to ensure dispatchability. Current inorganic salt-based TES systems in large-scale CSP plants generally employ molten nitrate salts for energy storage, but nitrate salts are limited in application to lower temperatures—generally, below 600 °C. These materials are sufficient for parabolic trough power plants, but they are inadequate for use at higher temperatures. At the higher operating temperatures achievable in solar power tower-type CSP plants, chloride salts are promising candidates for application as TES materials, owing to their thermal stability and generally lower cost compared to nitrate salts. In light of this, a recent study was conducted, which included a preliminary survey of chloride salts and binary eutectic systems that show promise as high temperature TES media. This study provided some basic information about the salts, including phase equilibria data and estimates of latent heat of fusion for some of the eutectics. Cost estimates were obtained through a review of bulk pricing for the pure salts among various vendors. This review paper updates that prior study, adding data for additional salt eutectic systems obtained from the literature. Where possible, data are obtained from the thermodynamic database software, FactSage. Radiative properties are presented, as well, since at higher temperatures, thermal radiation becomes a significant mode of heat transfer. Material compatibility for inorganic salts is another important consideration (e.g., with regard to piping and/or containment), so a summary of corrosion studies with various materials is also presented. Lastly, cost data for these systems are presented, allowing for meaningful comparison among these systems and other materials for TES

A solar receiver-storage modular cascade based on porous ceramic structures for hybrid sensible/thermochemical solar energy storage

Science.gov (United States)

Agrafiotis, Christos; de Oliveira, Lamark; Roeb, Martin; Sattler, Christian

2016-05-01

The current state-of-the-art solar heat storage concept in air-operated Solar Tower Power Plants is to store the solar energy provided during on-sun operation as sensible heat in porous solid materials that operate as recuperators during off-sun operation. The technology is operationally simple; however its storage capacity is limited to 1.5 hours. An idea for extending this capacity is to render this storage concept from "purely" sensible to "hybrid" sensible/ thermochemical one, via coating the porous heat exchange modules with oxides of multivalent metals for which their reduction/oxidation reactions are accompanied by significant heat effects, or by manufacturing them entirely of such oxides. In this way solar heat produced during on-sun operation can be used (in addition to sensibly heating the porous solid) to power the endothermic reduction of the oxide from its state with the higher metal valence to that of the lower; the thermal energy can be entirely recovered by the reverse exothermic oxidation reaction (in addition to sensible heat) during off-sun operation. Such sensible and thermochemical storage concepts were tested on a solar-irradiated receiver- heat storage module cascade for the first time. Parametric studies performed so far involved the comparison of three different SiC-based receivers with respect to their capability of supplying solar-heated air at temperatures sufficient for the reduction of the oxides, the effect of air flow rate on the temperatures achieved within the storage module, as well as the comparison of different porous storage media made of cordierite with respect to their sensible storage capacity.

PROCESS CONTROL STORAGE SMOKELESS TOBACCO (SNUS

Directory of Open Access Journals (Sweden)

T. A. Don

2015-01-01

Full Text Available An important aim during smokeless tobacco product (snus storage is keeping its quantitative and qualitative properties. Another significant factor is its biological safety due to its oral way of consumption. The main factors affecting quality during storage are: temperature, relative humidity, air composition, ventilation rate, surrounding products and package. Snus consumption is growing, but till present it was slightly spread in Russia and as a result little studied, thus studying process of its storage is an actual question. The aims of the research were: studying terms and methods of storage that provide constant product’s quality. Samples with different composition were taken for carrying research. Quality evaluation was carried according to standard for tobacco branch methods and to new methods developed in the laboratory of technologies for manufacturing tobacco products. Products were stored at lowered and room temperatures. It is discovered that snus with herbs added can be stored at room temperature and humidity not more than three months. Snus with coffee added can be stored not more than four months without changing its taste. Adding honey to this product slightly decreases its score by sensory evaluation, but remains it possible for consumption. Sensory testing score after storage at lowered temperature has remained unchanged. Optimal terms of storage were found. For room temperature they are: temperature 17-25 °C, relative air humidity 65 – 75 %, for lowered temperature – 5 °C and relative air humidity 50 -60 %. It was discovered that composition of snus and environmental parameters affect its storage duration.

Operation and maintenance of spent fuel storage and transportation casks/containers

International Nuclear Information System (INIS)

2007-01-01

Member States have a growing need for casks for spent fuel storage and transportation. A variety of casks has been developed and is in use at an increasing number of sites. This has resulted in an accumulation of experience that will provide valuable information for other projects in spent fuel management. This publication provides a comprehensive review of information on the cask operation and maintenance associated with spent fuel storage. It draws upon generic knowledge from industrial experience and applications and is intended to serve as a basis for better planning and implementation in future projects

A split-path schema-based RFID data storage model in supply chain management.

Science.gov (United States)

Fan, Hua; Wu, Quanyuan; Lin, Yisong; Zhang, Jianfeng

2013-05-03

In modern supply chain management systems, Radio Frequency IDentification (RFID) technology has become an indispensable sensor technology and massive RFID data sets are expected to become commonplace. More and more space and time are needed to store and process such huge amounts of RFID data, and there is an increasing realization that the existing approaches cannot satisfy the requirements of RFID data management. In this paper, we present a split-path schema-based RFID data storage model. With a data separation mechanism, the massive RFID data produced in supply chain management systems can be stored and processed more efficiently. Then a tree structure-based path splitting approach is proposed to intelligently and automatically split the movement paths of products . Furthermore, based on the proposed new storage model, we design the relational schema to store the path information and time information of tags, and some typical query templates and SQL statements are defined. Finally, we conduct various experiments to measure the effect and performance of our model and demonstrate that it performs significantly better than the baseline approach in both the data expression and path-oriented RFID data query performance.

A Split-Path Schema-Based RFID Data Storage Model in Supply Chain Management

Directory of Open Access Journals (Sweden)

Jianfeng Zhang

2013-05-01

Full Text Available In modern supply chain management systems, Radio Frequency IDentification (RFID technology has become an indispensable sensor technology and massive RFID data sets are expected to become commonplace. More and more space and time are needed to store and process such huge amounts of RFID data, and there is an increasing realization that the existing approaches cannot satisfy the requirements of RFID data management. In this paper, we present a split-path schema-based RFID data storage model. With a data separation mechanism, the massive RFID data produced in supply chain management systems can be stored and processed more efficiently. Then a tree structure-based path splitting approach is proposed to intelligently and automatically split the movement paths of products . Furthermore, based on the proposed new storage model, we design the relational schema to store the path information and time information of tags, and some typical query templates and SQL statements are defined. Finally, we conduct various experiments to measure the effect and performance of our model and demonstrate that it performs significantly better than the baseline approach in both the data expression and path-oriented RFID data query performance.

Effects of Agitation and Storage Temperature on Measurements of Hydration Status.

Science.gov (United States)

Adams, Heather M; Eberman, Lindsey E; Yeargin, Susan W; Niemann, Andrew J; Mata, Heather L; Dziedzicki, David J

2015-12-01

Hypohydration can have significant implications on normal physiological functions of the body. This study aimed to determine the impact of agitation, storage temperature, and storage time on urine osmolality compared to the criterion control. We used a descriptive diagnostic validity test design. To investigate agitation, we recruited 75 healthy individuals (males = 41, females = 34; mean age = 22 ± 5 years; mean self-reported height = 172 ± 23 cm and mass = 77 ± 17 kg) who provided one or more samples (total = 81). The independent variables were agitation (vortex, hand shaken, no agitation) and temperature (room temperature, freezer, and refrigerator) type. Participants completed informed consent, a health questionnaire and were asked to provide a urine sample, which was split and labeled according to agitation type or storage temperature. Urine osmolality was used to determine hydration status at two time points (within 2 hours [control], 48 hours). We used t-tests to determine the difference between each condition and the control and calculated percent error for each condition. No significant differences for no agitation (t79 = -0.079, P = 0.937), hand shaken (t79 = 1.395, P = 0.167) or vortex mixed (t79 = -0.753, P = 0.453) were identified when compared to the criterion control. No significant differences for room temperature (t82 = -0.720, P = 0.474), refrigerator (t82 = -2.697, P = 0.008) or freezer (t82 = 2.576, P = 0.012) were identified when compared to the criterion control. Our findings suggest agitation of urine specimen is not necessary and samples do not require refrigeration or freezing if assessed within 48 hours. Analysis within two hours of collection is not necessary and samples can be stored for up to 48 hours without impacting the hydration status of the sample.

Annual report of the industrial centre for regrouping, warehousing and storage - 2012

International Nuclear Information System (INIS)

2013-07-01

This report first presents the installations of the Cires (industrial centre for regrouping, warehousing and storage), its equipment and buildings, its activities (storage of very-low-activity wastes, regrouping and warehousing of non-electronuclear wastes). It reviews the arrangements regarding safety and radiation protection: radioactive waste storage safety, safety of non-electronuclear waste regrouping and warehousing, relationship with the regional directorate of environment, planning and housing (DREAL), quality audits, staff safety, and radiation protection. It addresses the actions undertaken for the control of the environment and of releases by the installations: radiological control in various locations (measurements in soils, waters, underground waters, and atmospheric releases), physical and chemical controls. The next part reports actions regarding transparency and information (visits, conferences, exhibitions, relationship with the local information and control commission)

Quantitative investigation of red blood cell three-dimensional geometric and chemical changes in the storage lesion using digital holographic microscopy.

Science.gov (United States)

Jaferzadeh, Keyvan; Moon, Inkyu

2015-11-01

Quantitative phase information obtained by digital holographic microscopy (DHM) can provide new insight into the functions and morphology of single red blood cells (RBCs). Since the functionality of a RBC is related to its three-dimensional (3-D) shape, quantitative 3-D geometric changes induced by storage time can help hematologists realize its optimal functionality period. We quantitatively investigate RBC 3-D geometric changes in the storage lesion using DHM. Our experimental results show that the substantial geometric transformation of the biconcave-shaped RBCs to the spherocyte occurs due to RBC storage lesion. This transformation leads to progressive loss of cell surface area, surface-to-volume ratio, and functionality of RBCs. Furthermore, our quantitative analysis shows that there are significant correlations between chemical and morphological properties of RBCs.

Special storage of leaking fuel at Paks NPP

International Nuclear Information System (INIS)

Biro, Janos; Szőke, L.; Burján, T.; Lukács, R.; Hózer, H.

2015-01-01

In this paper the activities related with spent, hermetic as well as leaking fuel handling and storage, including: Spent fuel pool; Transportation criteria for the spent fuel assemblies and Interim spent fuel dry storage; Short-term storage in the spent fuel pool; Identification of the leaking assemblies by the TS-device; Present conception of Identification, handling of the leaking FAs; Modified transport procedure for the leaking FAs; Calculation of solved activity inside the leaking fuel rod; Solved activity limit values for the leaking FAs; Long-term storage in the interim spent Fuel dry storage are presented. At the end authors’ concluded that: 1) The leaking FA can be transported to the interim dry storage together with the other spent fuel assemblies in the transport container. 2) The transport-documentation of the leaking FA has to contain: isotope inventory, calculated solved activity values of the failed FA and the quantity of failed fuel rods. 3) Performing three leakage tests of the identified leaking FA before the transportation in the 5FP. it is useful to decrease the solved activity concentration inside the leaking FA and give additional information about the extent of the leakage. 4) We can calculate simply the solved activity of the leaking FA. 5) The modified transport procedure will have to be authorized. 6) The radiological effects of the leaking FA are negligible relative to the natural background radiation

A Central Capacity Limit to the Simultaneous Storage of Visual and Auditory Arrays in Working Memory

Science.gov (United States)

Saults, J. Scott; Cowan, Nelson

2007-01-01

If working memory is limited by central capacity (e.g., the focus of attention; N. Cowan, 2001), then storage limits for information in a single modality should apply also to the simultaneous storage of information from different modalities. The authors investigated this by combining a visual-array comparison task with a novel auditory-array…

Locally Minimum Storage Regenerating Codes in Distributed Cloud Storage Systems

Institute of Scientific and Technical Information of China (English)

Jing Wang; Wei Luo; Wei Liang; Xiangyang Liu; Xiaodai Dong

2017-01-01

In distributed cloud storage sys-tems, inevitably there exist multiple node fail-ures at the same time. The existing methods of regenerating codes, including minimum storage regenerating (MSR) codes and mini-mum bandwidth regenerating (MBR) codes, are mainly to repair one single or several failed nodes, unable to meet the repair need of distributed cloud storage systems. In this paper, we present locally minimum storage re-generating (LMSR) codes to recover multiple failed nodes at the same time. Specifically, the nodes in distributed cloud storage systems are divided into multiple local groups, and in each local group (4, 2) or (5, 3) MSR codes are constructed. Moreover, the grouping method of storage nodes and the repairing process of failed nodes in local groups are studied. The-oretical analysis shows that LMSR codes can achieve the same storage overhead as MSR codes. Furthermore, we verify by means of simulation that, compared with MSR codes, LMSR codes can reduce the repair bandwidth and disk I/O overhead effectively.

Assessing storage adequacy

International Nuclear Information System (INIS)

Amirault, P.

2004-01-01

Government policy encourages the use of natural gas. It is expected that liquefied natural gas (LNG) and Arctic gas will make up 20 to 25 per cent of supply. This presentation provided an outlook of storage value based on a technical analysis by the National Petroleum Counsel (NPC) report. A moderately robust growth is expected in the residential and commercial load which may be partially offset by robust growth in electricity. The net result is an increase in storage requirements. It was concluded that there is a strong case for growth in storage demand but a lack of good sites for additional capacity. This will lead to higher storage values. The NPC sees the need for 1 Tcf more storage use by 2025, of which 700 Bcf will need to come from new storage. In particular, current storage levels may not be sufficient to meet a colder than normal winter, and deliverability is affected by field inventory. Most storage capacity was built before 1985, mostly by regulated entities. It is expected that only 250 to 400 Bcf will be added over the next 25 years in North America. If storage becomes scarce, prices will move to the marginal cost of new additions, and the upper limit on price will be determined by salt cavern storage. An increase of $1.00 in the price of leasing storage would add about $0.11 to the average price of consumed gas. tabs., figs

Long-time data storage: relevant time scales

NARCIS (Netherlands)

Elwenspoek, Michael Curt

2011-01-01

Dynamic processes relevant for long-time storage of information about human kind are discussed, ranging from biological and geological processes to the lifecycle of stars and the expansion of the universe. Major results are that life will end ultimately and the remaining time that the earth is

Storage of Maize in Purdue Improved Crop Storage (PICS) Bags.

Science.gov (United States)

Williams, Scott B; Murdock, Larry L; Baributsa, Dieudonne

2017-01-01

Interest in using hermetic technologies as a pest management solution for stored grain has risen in recent years. One hermetic approach, Purdue Improved Crop Storage (PICS) bags, has proven successful in controlling the postharvest pests of cowpea. This success encouraged farmers to use of PICS bags for storing other crops including maize. To assess whether maize can be safely stored in PICS bags without loss of quality, we carried out laboratory studies of maize grain infested with Sitophilus zeamais (Motshulsky) and stored in PICS triple bags or in woven polypropylene bags. Over an eight month observation period, temperatures in the bags correlated with ambient temperature for all treatments. Relative humidity inside PICS bags remained constant over this period despite the large changes that occurred in the surrounding environment. Relative humidity in the woven bags followed ambient humidity closely. PICS bags containing S. zeamais-infested grain saw a significant decline in oxygen compared to the other treatments. Grain moisture content declined in woven bags, but remained high in PICS bags. Seed germination was not significantly affected over the first six months in all treatments, but declined after eight months of storage when infested grain was held in woven bags. Relative damage was low across treatments and not significantly different between treatments. Overall, maize showed no signs of deterioration in PICS bags versus the woven bags and PICS bags were superior to woven bags in terms of specific metrics of grain quality.

The united kingdom's changing requirements for spent fuel storage

International Nuclear Information System (INIS)

Hodgson, Z.; Hambley, D.I.; Gregg, R.; Ross, D.N.

2013-01-01

The UK is adopting an open fuel cycle, and is necessarily moving to a regime of long term storage of spent fuel, followed by geological disposal once a geological disposal facility (GDF) is available. The earliest GDF receipt date for legacy spent fuel is assumed to be 2075. The UK is set to embark on a programme of new nuclear build to maintain a nuclear energy contribution of 16 GW. Additionally, the UK are considering a significant expansion of nuclear energy in order to meet carbon reduction targets and it is plausible to foresee a scenario where up to 75 GW from nuclear power production could be deployed in the UK by the mid 21. century. Such an expansion, could lead to spent fuel storage and its disposal being a dominant issue for the UK Government, the utilities and the public. If the UK were to transition a closed fuel cycle, then spent fuel storage should become less onerous depending on the timescales. The UK has demonstrated a preference for wet storage of spent fuel on an interim basis. The UK has adopted an approach of centralised storage, but a 16 GW new build programme and any significant expansion of this may push the UK towards distributed spent fuel storage at a number of reactors station sites across the UK

SUBTASK 2.19 – OPERATIONAL FLEXIBILITY OF CO2 TRANSPORT AND STORAGE

Energy Technology Data Exchange (ETDEWEB)

Jensen, Melanie; Schlasner, Steven; Sorensen, James; Hamling, John

2014-12-31

Carbon dioxide (CO2) is produced in large quantities during electricity generation and by industrial processes. These CO2 streams vary in terms of both composition and mass flow rate, sometimes substantially. The impact of a varying CO2 stream on pipeline and storage operation is not fully understood in terms of either operability or infrastructure robustness. This study was performed to summarize basic background from the literature on the topic of operational flexibility of CO2 transport and storage, but the primary focus was on compiling real-world lessons learned about flexible operation of CO2 pipelines and storage from both large-scale field demonstrations and commercial operating experience. Modeling and pilot-scale results of research in this area were included to illustrate some of the questions that exist relative to operation of carbon capture and storage (CCS) projects with variable CO2 streams. It is hoped that this report’s real-world findings provide readers with useful information on the topic of transport and storage of variable CO2 streams. The real-world results were obtained from two sources. The first source consisted of five full-scale, commercial transport–storage projects: Sleipner, Snøhvit, In Salah, Weyburn, and Illinois Basin–Decatur. These scenarios were reviewed to determine the information that is available about CO2 stream variability/intermittency on these demonstration-scale projects. The five projects all experienced mass flow variability or an interruption in flow. In each case, pipeline and/or injection engineers were able to accommodate any issues that arose. Significant variability in composition has not been an issue at these five sites. The second source of real- world results was telephone interviews conducted with experts in CO2 pipeline transport, injection, and storage during which commercial anecdotal information was acquired to augment that found during the literature search of the five full-scale projects. The

Environmental sciences information storage and retrieval system

International Nuclear Information System (INIS)

Engstrom, D.E.

1975-01-01

Reynolds Electrical and Engineering Co., Inc. (REECo), has since 1970 accumulated information relating to the AEC's Nevada Applied Ecology Group (NAEG) programs at the Nevada Test Site (NTS). These programs, involving extensive soil, vegetation, and small-animal studies, have generated informational data concerning the collecting, processing, analyzing, and shipping of sample materials to various program participants and contractors. Future plans include incorporation of Lawrence Livermore Laboratory's resuspension study data, REECo's on-site air data, and EPA's large-animal, off-site air, and off-site soil data. (auth)

Storage Policies and Optimal Shape of a Storage System

NARCIS (Netherlands)

Zaerpour, N.; De Koster, René; Yu, Yugang

2013-01-01

The response time of a storage system is mainly influenced by its shape (configuration), the storage assignment and retrieval policies, and the location of the input/output (I/O) points. In this paper, we show that the optimal shape of a storage system, which minimises the response time for single

Managing aging effects on dry cask storage systems for extended long-term storage and transportation of used fuel - rev. 0

Energy Technology Data Exchange (ETDEWEB)

Chopra, O.K.; Diercks, D.; Fabian, R.; Ma, D.; Shah, V.; Tam, S.W.; Liu, Y. (Decision and Information Sciences); ( EVS); ( NE)

2012-07-06

The cancellation of the Yucca Mountain repository program in the United States raises the prospect of extended long-term storage (i.e., >120 years) and deferred transportation of used fuel at operating and decommissioned nuclear power plant sites. Under U.S. federal regulations contained in Title 10 of the Code of Federal Regulations (CFR) 72.42, the initial license term for an Independent Spent Fuel Storage Installation (ISFSI) must not exceed 40 years from the date of issuance. Licenses may be renewed by the U.S. Nuclear Regulatory Commission (NRC) at the expiration of the license term upon application by the licensee for a period not to exceed 40 years. Application for ISFSI license renewals must include the following: (1) Time-limited aging analyses (TLAAs) that demonstrate that structures, systems, and components (SSCs) important to safety will continue to perform their intended function for the requested period of extended operation; and (2) a description of the aging management program (AMP) for management of issues associated with aging that could adversely affect SSCs important to safety. In addition, the application must also include design bases information as documented in the most recent updated final safety analysis report as required by 10 CFR 72.70. Information contained in previous applications, statements, or reports filed with the Commission under the license may be incorporated by reference provided that those references are clear and specific. The NRC has recently issued the Standard Review Plan (SRP) for renewal of used-fuel dry cask storage system (DCSS) licenses and Certificates of Compliance (CoCs), NUREG-1927, under which NRC may renew a specific license or a CoC for a term not to exceed 40 years. Both the license and the CoC renewal applications must contain revised technical requirements and operating conditions (fuel storage, surveillance and maintenance, and other requirements) for the ISFSI and DCSS that address aging effects that

Energy storage device based on flywheel, power converters and Simulink real-time

DEFF Research Database (Denmark)

Blaabjerg, Frede; Kedra, Bartosz; Malkowski, Robert

2017-01-01

by Gdansk University of Technology in Poland. Paper is divided into four sections. First section of the paper provides introductory information on the Energy Storage Device and its capabilities. In the second section of the paper concept of the unit is presented. Requirements for the unit are described...... as well as proposed and introduced functions are listed. Implementation details are given in third section of paper. Hardware structure is presented and described. Information about used communication interface, data maintenance and storage solution, as well as used Simulink realtime features...

Effective grouping for energy and performance: Construction of adaptive, sustainable, and maintainable data storage

Science.gov (United States)

Essary, David S.

The performance gap between processors and storage systems has been increasingly critical over the years. Yet the performance disparity remains, and further, storage energy consumption is rapidly becoming a new critical problem. While smarter caching and predictive techniques do much to alleviate this disparity, the problem persists, and data storage remains a growing contributor to latency and energy consumption. Attempts have been made at data layout maintenance, or intelligent physical placement of data, yet in practice, basic heuristics remain predominant. Problems that early studies sought to solve via layout strategies were proven to be NP-Hard, and data layout maintenance today remains more art than science. With unknown potential and a domain inherently full of uncertainty, layout maintenance persists as an area largely untapped by modern systems. But uncertainty in workloads does not imply randomness; access patterns have exhibited repeatable, stable behavior. Predictive information can be gathered, analyzed, and exploited to improve data layouts. Our goal is a dynamic, robust, sustainable predictive engine, aimed at improving existing layouts by replicating data at the storage device level. We present a comprehensive discussion of the design and construction of such a predictive engine, including workload evaluation, where we present and evaluate classical workloads as well as our own highly detailed traces collected over an extended period. We demonstrate significant gains through an initial static grouping mechanism, and compare against an optimal grouping method of our own construction, and further show significant improvement over competing techniques. We also explore and illustrate the challenges faced when moving from static to dynamic (i.e. online) grouping, and provide motivation and solutions for addressing these challenges. These challenges include metadata storage, appropriate predictive collocation, online performance, and physical placement

ES-5052 storage devices on magnetic disks for the BESM-4 computer

International Nuclear Information System (INIS)

Bezrukova, N.B.; Vinogradov, A.F.; Eliseev, G.N.; Ivanchenko, Z.M.; Pervushov, V.I.; Samojlov, V.N.; Stuk, G.P.; Shchelev, S.A.; Chulkov, N.I.

1975-01-01

The basic principles of connection between ES-5052 magnetic disk storage devices and a BESM-4 computer are set forth. The interchange of instructions and guidance information between computer and magnetic disk storage is accomplished through a disk controlling unit. The time taken to find the required cylinder (to pass from track to track) is 20 ms, the access time is 60 to 95 ms. The data transfer rate (512 45-digit machine words) is 20 ms. The total disk storage capacity is equivalent to 250 BESM-4 memory units. The instructions for BESM-4 access to the ES-5052 magnetic disk storage are described

Corrosion experiments on stainless steels used in dry storage canisters of spent nuclear fuel

Energy Technology Data Exchange (ETDEWEB)

Ryskamp, J.M.; Adams, J.P.; Faw, E.M.; Anderson, P.A.

1996-09-01

Nonradioactive (cold) experiments have been set up in the Idaho Chemical Processing Plant (ICPP)-1634, and radioactive (hot) experiments have been set up in the Irradiated Fuel Storage Facility (IFSF) at ICPP. The objective of these experiments is to provide information on the interactions (corrosion) between the spent nuclear fuel currently stored at the ICPP and the dry storage canisters and containment materials in which this spent fuel will be stored for the next several decades. This information will be used to help select canister materials that will retain structural integrity over this period within economic, criticality, and other constraints. The two purposes for Dual Purpose Canisters (DPCs) are for interim storage of spent nuclear fuel and for shipment to a final geological repository. Information on how corrosion products, sediments, and degraded spent nuclear fuel may corrode DPCs will be required before the DPCs will be allowed to be shipped out of the State of Idaho. The information will also be required by the Nuclear Regulatory Commission (NRC) to support the licensing of DPCs. Stainless steels 304L and 316L are the most likely materials for dry interim storage canisters. Welded stainless steel coupons are used to represent the canisters in both hot and cold experiments.

Corrosion experiments on stainless steels used in dry storage canisters of spent nuclear fuel

International Nuclear Information System (INIS)

Ryskamp, J.M.; Adams, J.P.; Faw, E.M.; Anderson, P.A.

1996-09-01

Nonradioactive (cold) experiments have been set up in the Idaho Chemical Processing Plant (ICPP)-1634, and radioactive (hot) experiments have been set up in the Irradiated Fuel Storage Facility (IFSF) at ICPP. The objective of these experiments is to provide information on the interactions (corrosion) between the spent nuclear fuel currently stored at the ICPP and the dry storage canisters and containment materials in which this spent fuel will be stored for the next several decades. This information will be used to help select canister materials that will retain structural integrity over this period within economic, criticality, and other constraints. The two purposes for Dual Purpose Canisters (DPCs) are for interim storage of spent nuclear fuel and for shipment to a final geological repository. Information on how corrosion products, sediments, and degraded spent nuclear fuel may corrode DPCs will be required before the DPCs will be allowed to be shipped out of the State of Idaho. The information will also be required by the Nuclear Regulatory Commission (NRC) to support the licensing of DPCs. Stainless steels 304L and 316L are the most likely materials for dry interim storage canisters. Welded stainless steel coupons are used to represent the canisters in both hot and cold experiments

105-H Reactor Interim Safe Storage Project Final Report

International Nuclear Information System (INIS)

Ison, E.G.

2008-01-01

The following information documents the decontamination and decommissioning of the 105-H Reactor facility, and placement of the reactor core into interim safe storage. The D and D of the facility included characterization, engineering, removal of hazardous and radiologically contaminated materials, equipment removal, decontamination, demolition of the structure, and restoration of the site. The ISS work also included construction of the safe storage enclosure, which required the installation of a new roofing system, power and lighting, a remote monitoring system, and ventilation components.

Storage Time and Urine Biomarker Levels in the ASSESS-AKI Study.

Directory of Open Access Journals (Sweden)

Kathleen D Liu

Full Text Available Although stored urine samples are often used in biomarker studies focused on acute and chronic kidney disease, how storage time impacts biomarker levels is not well understood.866 subjects enrolled in the NIDDK-sponsored ASsessment, Serial Evaluation, and Subsequent Sequelae in Acute Kidney Injury (ASSESS-AKI Study were included. Samples were processed under standard conditions and stored at -70°C until analyzed. Kidney injury molecule-1 (KIM-1, neutrophil gelatinase-associated lipocalin (NGAL, interleukin-18 (IL-18, and liver fatty acid binding protein (L-FABP were measured in urine samples collected during the index hospitalization or an outpatient visit 3 months later. Mixed effects models were used to determine the effect of storage time on biomarker levels and stratified by visit.Median storage was 17.8 months (25-75% IQR 10.6-23.7 for samples from the index hospitalization and 14.6 months (IQR 7.3-20.4 for outpatient samples. In the mixed effects models, the only significant association between storage time and biomarker concentration was for KIM-1 in outpatient samples, where each month of storage was associated with a 1.7% decrease (95% CI -3% to -0.3%. There was no relationship between storage time and KIM-1 levels in samples from the index hospitalization.There was no significant impact of storage time over a median of 18 months on urine KIM-1, NGAL, IL-18 or L-FABP in hospitalized samples; a statistically significant effect towards a decrease over time was noted for KIM-1 in outpatient samples. Additional studies are needed to determine whether longer periods of storage at -70°C systematically impact levels of these analytes.

Edge-Based Efficient Search over Encrypted Data Mobile Cloud Storage.

Science.gov (United States)

Guo, Yeting; Liu, Fang; Cai, Zhiping; Xiao, Nong; Zhao, Ziming

2018-04-13

Smart sensor-equipped mobile devices sense, collect, and process data generated by the edge network to achieve intelligent control, but such mobile devices usually have limited storage and computing resources. Mobile cloud storage provides a promising solution owing to its rich storage resources, great accessibility, and low cost. But it also brings a risk of information leakage. The encryption of sensitive data is the basic step to resist the risk. However, deploying a high complexity encryption and decryption algorithm on mobile devices will greatly increase the burden of terminal operation and the difficulty to implement the necessary privacy protection algorithm. In this paper, we propose ENSURE (EfficieNt and SecURE), an efficient and secure encrypted search architecture over mobile cloud storage. ENSURE is inspired by edge computing. It allows mobile devices to offload the computation intensive task onto the edge server to achieve a high efficiency. Besides, to protect data security, it reduces the information acquisition of untrusted cloud by hiding the relevance between query keyword and search results from the cloud. Experiments on a real data set show that ENSURE reduces the computation time by 15% to 49% and saves the energy consumption by 38% to 69% per query.

Edge-Based Efficient Search over Encrypted Data Mobile Cloud Storage

Directory of Open Access Journals (Sweden)

Yeting Guo

2018-04-01

Full Text Available Smart sensor-equipped mobile devices sense, collect, and process data generated by the edge network to achieve intelligent control, but such mobile devices usually have limited storage and computing resources. Mobile cloud storage provides a promising solution owing to its rich storage resources, great accessibility, and low cost. But it also brings a risk of information leakage. The encryption of sensitive data is the basic step to resist the risk. However, deploying a high complexity encryption and decryption algorithm on mobile devices will greatly increase the burden of terminal operation and the difficulty to implement the necessary privacy protection algorithm. In this paper, we propose ENSURE (EfficieNt and SecURE, an efficient and secure encrypted search architecture over mobile cloud storage. ENSURE is inspired by edge computing. It allows mobile devices to offload the computation intensive task onto the edge server to achieve a high efficiency. Besides, to protect data security, it reduces the information acquisition of untrusted cloud by hiding the relevance between query keyword and search results from the cloud. Experiments on a real data set show that ENSURE reduces the computation time by 15% to 49% and saves the energy consumption by 38% to 69% per query.

Edge-Based Efficient Search over Encrypted Data Mobile Cloud Storage

Science.gov (United States)

Liu, Fang; Cai, Zhiping; Xiao, Nong; Zhao, Ziming

2018-01-01

Smart sensor-equipped mobile devices sense, collect, and process data generated by the edge network to achieve intelligent control, but such mobile devices usually have limited storage and computing resources. Mobile cloud storage provides a promising solution owing to its rich storage resources, great accessibility, and low cost. But it also brings a risk of information leakage. The encryption of sensitive data is the basic step to resist the risk. However, deploying a high complexity encryption and decryption algorithm on mobile devices will greatly increase the burden of terminal operation and the difficulty to implement the necessary privacy protection algorithm. In this paper, we propose ENSURE (EfficieNt and SecURE), an efficient and secure encrypted search architecture over mobile cloud storage. ENSURE is inspired by edge computing. It allows mobile devices to offload the computation intensive task onto the edge server to achieve a high efficiency. Besides, to protect data security, it reduces the information acquisition of untrusted cloud by hiding the relevance between query keyword and search results from the cloud. Experiments on a real data set show that ENSURE reduces the computation time by 15% to 49% and saves the energy consumption by 38% to 69% per query. PMID:29652810

Data survivability vs. security in information systems

International Nuclear Information System (INIS)

Levitin, Gregory; Hausken, Kjell; Taboada, Heidi A.; Coit, David W.

2012-01-01

A multiple objective problem formulation and solution methodology is presented to select optimal information and data storage configurations considering both data survivability and data security, as well as cost. This paper considers a situation where the information is divided into several separately stored blocks in order to mitigate the risk of unauthorized access or theft. The information can be used only if all of the blocks are accessed. To impede the information theft, the defender prefers to maximize the number of blocks. On the other hand the destruction of any block destroys the integrity of information and makes it impossible to use. To impede the information destruction, the defender prefers to maximize the number of parallel (reserve) copies of each block, regardless how many blocks in series there are. Given the set of available information storage resources, the defender must consider a multi-objective optimization problem to determine how many blocks and their copies to create, and how to distribute them among available resources in order to minimize information vulnerability, insecurity, and storage cost. Non-dominated solutions to this problem are determined using a multiple objective genetic algorithm (MOGA). This methodology is demonstrated with two general examples.

Using Deduplicating Storage for Efficient Disk Image Deployment

Directory of Open Access Journals (Sweden)

Xing Lin

2015-08-01

Full Text Available Many clouds and network testbeds use disk images to initialize local storage on their compute devices. Large facilities must manage thousands or more images, requiring significant amounts of storage. At the same time, to provide a good user experience, they must be able to deploy those images quickly. Driven by our experience in operating the Emulab site at the University of Utah---a long-lived and heavily-used testbed---we have created a new service for efficiently storing and deploying disk images. This service exploits the redundant data found in similar images, using deduplication to greatly reduce the amount of physical storage required. In addition to space savings, our system is also designed for highly efficient image deployment---it integrates with an existing highly-optimized disk image deployment system, Frisbee, without significantly increasing the time required to distribute and install images. In this paper, we explain the design of our system and discuss the trade-offs we made to strike a balance between efficient storage and fast disk image deployment. We also propose a new chunking algorithm, called AFC, which enables fixed-size chunking for deduplicating allocated disk sectors. Experimental results show that our system reduces storage requirements by up to 3x while imposing only a negligible runtime overhead on the end-to-end disk-deployment process.

Optical Storage and Optical Information Held in Taipei, Taiwan on 26-27 July 2000

National Research Council Canada - National Science Library

Shieh, H.-P. D

2000-01-01

.... In the area of data storage, topics include devices to improve the performance of optical heads, measurement of optical media parameters, new superresolution techniques, three-dimensional memory, and near-field devices...

Assessment of the polytank for fumigation and storage of cowpea

International Nuclear Information System (INIS)

Ademang Korletey, Francis

2009-06-01

Insect infestation of cowpea (Vigna unguiculata) in storage is identified as a major constraint facing cowpea farmers in Ghana. The major insect pest causing losses to stored cowpea in West Africa is the cowpea weevil (Callosobruchus maculatus). Fumigation is the most effective control method against cowpea weevil considering its mode of infestation. The jute sack lined with a plastic film bag commonly used by farmers for fumigation and storage is very delicate to handle, not sufficiently airtight for fumigation and easily attacked by rodents. The objectives of the project were to (1) assess the polytank for fumigation and storage of cowpea, and (2) compare the storage qualities of stored cowpea using the polytank and jute sack lined with a plastic film bag. The cowpea was fumigated using aluminium phosphide tablets for a period of 7 days and stored for six mouths. Data was collected, analysed and compared between the two storage containers on seed germination, seed vigour, grain moisture content, insect infestation, percentage usable proportion by number and by weight before, mid-storage and after the trial. The levels of phosphine gas concentration in the polytank and the jute sack were assessed daily for 7 days. The results showed no significant differences (1% probability) between the two storage containers in their performance as storage containers in terms of grain moisture content, seed germination, seed vigour, insect infestation, percentage usable proportion by number and by weight. There was also significant difference (5%) in phosphine gas concentration between the two storage containers in their performance as fumigation containers except on day one. However, it was found that fumigation and storage using the polytank had a greater advantage over the jute sack lined with plastic film bag in terms of air tightness, handling and resistance to rodent attacks. (au)

Seed storage-mediated dormancy alleviation in Fabaceae from campo rupestre