Cast Stone Formulation At Higher Sodium Concentrations

Energy Technology Data Exchange (ETDEWEB)

Fox, K. M.; Edwards, T. A.; Roberts, K. B.

2013-10-02

A low temperature waste form known as Cast Stone is being considered to provide supplemental Low Activity Waste (LAW) immobilization capacity for the Hanford site. Formulation of Cast Stone at high sodium concentrations is of interest since a significant reduction in the necessary volume of Cast Stone and subsequent disposal costs could be achieved if an acceptable waste form can be produced with a high sodium molarity salt solution combined with a high water to premix (or dry blend) ratio. The objectives of this study were to evaluate the factors involved with increasing the sodium concentration in Cast Stone, including production and performance properties and the retention and release of specific components of interest. Three factors were identified for the experimental matrix: the concentration of sodium in the simulated salt solution, the water to premix ratio, and the blast furnace slag portion of the premix. The salt solution simulants used in this study were formulated to represent the overall average waste composition. The cement, blast furnace slag, and fly ash were sourced from a supplier in the Hanford area in order to be representative. The test mixes were prepared in the laboratory and fresh properties were measured. Fresh density increased with increasing sodium molarity and with decreasing water to premix ratio, as expected given the individual densities of these components. Rheology measurements showed that all of the test mixes produced very fluid slurries. The fresh density and rheology data are of potential value in designing a future Cast Stone production facility. Standing water and density gradient testing showed that settling is not of particular concern for the high sodium compositions studied. Heat of hydration measurements may provide some insight into the reactions that occur within the test mixes, which may in turn be related to the properties and performance of the waste form. These measurements showed that increased sodium

Cast Stone Formulation At Higher Sodium Concentrations

Energy Technology Data Exchange (ETDEWEB)

Fox, K. M.; Roberts, K. A.; Edwards, T. B.

2013-09-17

A low temperature waste form known as Cast Stone is being considered to provide supplemental Low Activity Waste (LAW) immobilization capacity for the Hanford site. Formulation of Cast Stone at high sodium concentrations is of interest since a significant reduction in the necessary volume of Cast Stone and subsequent disposal costs could be achieved if an acceptable waste form can be produced with a high sodium molarity salt solution combined with a high water to premix (or dry blend) ratio. The objectives of this study were to evaluate the factors involved with increasing the sodium concentration in Cast Stone, including production and performance properties and the retention and release of specific components of interest. Three factors were identified for the experimental matrix: the concentration of sodium in the simulated salt solution, the water to premix ratio, and the blast furnace slag portion of the premix. The salt solution simulants used in this study were formulated to represent the overall average waste composition. The cement, blast furnace slag, and fly ash were sourced from a supplier in the Hanford area in order to be representative. The test mixes were prepared in the laboratory and fresh properties were measured. Fresh density increased with increasing sodium molarity and with decreasing water to premix ratio, as expected given the individual densities of these components. Rheology measurements showed that all of the test mixes produced very fluid slurries. The fresh density and rheology data are of potential value in designing a future Cast Stone production facility. Standing water and density gradient testing showed that settling is not of particular concern for the high sodium compositions studied. Heat of hydration measurements may provide some insight into the reactions that occur within the test mixes, which may in turn be related to the properties and performance of the waste form. These measurements showed that increased sodium

Effects of immersion disinfection of agar-alginate combined impressions on the surface properties of stone casts.

Science.gov (United States)

Iwasaki, Yukiko; Hiraguchi, Hisako; Iwasaki, Eriko; Yoneyama, Takayuki

2016-01-01

This study investigated the effects of disinfection of agar-alginate combined impressions on the surface properties of the resulting stone casts. Two brands of cartridge-form agar impression material and one alginate impression material were used. Agar-alginate combined impressions of smooth glass plates were prepared. The impressions were immersed in 0.55% ortho-phthalaldehyde solution or 0.5% sodium hypochlorite solution for 1, 3, 5 and 10 min. A stone cast made with an impression that had not been immersed was prepared as a control. The surface roughness (Ra) of the stone casts was measured, and the cast surfaces were observed by SEM. Immersion of agar-alginate combined impressions in 0.5% sodium hypochlorite solution for up to 10 min had no serious adverse effects on the surface properties of the stone casts. In contrast, even 1 min of immersion in 0.55% ortho-phthalaldehyde solution caused deterioration of the cast surface properties.

Cast Stone Oxidation Front Evaluation: Preliminary Results For Samples Exposed To Moist Air

International Nuclear Information System (INIS)

Langton, C. A.; Almond, P. M.

2013-01-01

The rate of oxidation is important to the long-term performance of reducing salt waste forms because the solubility of some contaminants, e.g., technetium, is a function of oxidation state. TcO 4 - in the salt solution is reduced to Tc(IV) and has been shown to react with ingredients in the waste form to precipitate low solubility sulfide and/or oxide phases. Upon exposure to oxygen, the compounds containing Tc(IV) oxidize to the pertechnetate ion, Tc(VII)O 4 - , which is very soluble. Consequently the rate of technetium oxidation front advancement into a monolith and the technetium leaching profile as a function of depth from an exposed surface are important to waste form performance and ground water concentration predictions. An approach for measuring contaminant oxidation rate (effective contaminant specific oxidation rate) based on leaching of select contaminants of concern is described in this report. In addition, the relationship between reduction capacity and contaminant oxidation is addressed. Chromate (Cr(VI) was used as a non-radioactive surrogate for pertechnetate, Tc(VII), in Cast Stone samples prepared with 5 M Simulant. Cast Stone spiked with pertechnetate was also prepared and tested. Depth discrete subsamples spiked with Cr were cut from Cast Stone exposed to Savannah River Site (SRS) outdoor ambient temperature fluctuations and moist air. Depth discrete subsamples spiked with Tc-99 were cut from Cast Stone exposed to laboratory ambient temperature fluctuations and moist air. Similar conditions are expected to be encountered in the Cast Stone curing container. The leachability of Cr and Tc-99 and the reduction capacities, measured by the Angus-Glasser method, were determined for each subsample as a function of depth from the exposed surface. The results obtained to date were focused on continued method development and are preliminary and apply to the sample composition and curing / exposure conditions described in this report. The Cr oxidation front

Marginal adaptation of four inlay casting waxes on stone, titanium, and zirconia dies.

Science.gov (United States)

Michalakis, Konstantinos X; Kapsampeli, Vassiliki; Kitsou, Aikaterini; Kirmanidou, Yvone; Fotiou, Anna; Pissiotis, Argirios L; Calvani, Pasquale Lino; Hirayama, Hiroshi; Kudara, Yukio

2014-07-01

Different inlay casting waxes do not produce copings with satisfactory marginal accuracy when used on different die materials. The purpose of this study was to evaluate the marginal accuracy of 4 inlay casting waxes on stone dies and titanium and zirconia abutments and to correlate the findings with the degree of wetting between the die specimens and the inlay casting waxes. The inlay casting waxes tested were Starwax (Dentaurum), Unterziehwachs (Bredent), SU Esthetic wax (Schuler), and Sculpturing wax (Renfert). The marginal opening of the waxes was measured with a stereomicroscope on high-strength stone dies and on titanium and zirconia abutments. Photographic images were obtained, and the mean marginal opening for each specimen was calculated. A total of 1440 measurements were made. Wetting between die materials and waxes was determined after fabricating stone, titanium, and zirconia rectangular specimens. A calibrated pipette was used to place a drop of molten wax onto each specimen. The contact angle was calculated with software after an image of each specimen had been made with a digital camera. Collected data were subjected to a 2-way analysis of variance (α=.05). Any association between marginal accuracy and wetting of different materials was found by using the Pearson correlation. The wax factor had a statistically significant effect both on the marginal discrepancy (F=158.31, P<.001) and contact angle values (F=68.09, P<.001). A statistically significant effect of the die material factor both on the marginal adaptation (F=503.47, P<.001) and contact angle values (F=585.02, P<.001) was detected. A significant correlation between the marginal accuracy and the contact angle values (Pearson=0.881, P=.01) was also found. Stone dies provided wax copings with the best marginal integrity, followed by titanium and zirconia abutments. Unterziehwachs (Bredent), wax produced the best marginal adaptation on different die materials. A significant correlation was found

Efficacy of Disinfection of Dental Stone Casts: Virkon versus Sodium Hypochlorite

Directory of Open Access Journals (Sweden)

Elnaz Moslehifard

2015-10-01

Full Text Available Objectives: The purpose of this experimental study was to compare the disinfection efficacy of sodium hypochlorite and peroxygenic acid (Virkon solutions for dental stone casts contaminated with microbial strains.Materials and Methods: A total of 960 spherical stone beads with a diameter of 10 mm were prepared and used as carriers of bacterial inoculums. They were individually inoculated by soaking in broth culture media containing each of the four understudy microorganisms. Different concentrations of Virkon and hypochlorite solutions were prepared using distilled water and then were sprayed on the surfaces of dental casts contaminated with Staphylococcus aureus, Pseudomonas aeruginosa, Bacillus subtilis and Candida albicans. The pour plate technique was used to evaluate the antimicrobi- al efficacy of each solution. Microbicidal effect (ME was calculated according to the log10 of control colony counts minus the log10 of the remaining colony counts after the antimicrobial procedure. Statistical difference was assessed using the Kruskal Wallis and the Man Whitney U tests with a significance of 95%.Results: We observed different bactericidal effects of Virkon at various concentra- tions; 1% Virkon killed S. aureus, P aeruginosa, and Candida albicans, while 3% Virkon solution was required to kill B. subtilis. For S. aureus, P. aeruginosa, and C. albicans, no significant difference was observed between1% Virkon and 0.525% so- dium hypochlorite (P >0.05. For B. subtilis, the efficacy of 3% Virkon and 0.525%sodium hypochlorite was not significantly different (P >0.999.Conclusion: According to the obtained results for Virkon and based on its low toxici- ty and good environmental compatibility, it may be recommended as an antimicrobial disinfectant for dental stone casts as non-critical items.

Engineering scale demonstration of a prospective Cast Stone process

International Nuclear Information System (INIS)

Cozzi, A.; Fowley, M.; Hansen, E.; Fox, K.; Miller, D.; Williams, M.

2014-01-01

This report documents an engineering-scale demonstration with non-radioactive simulants that was performed at SRNL using the Scaled Continuous Processing Facility (SCPF) to fill an 8.5 ft container with simulated Cast Stone grout. The Cast Stone formulation was chosen from the previous screening tests. Legacy salt solution from previous Hanford salt waste testing was adjusted to correspond to the average composition generated from the Hanford Tank Waste Operation Simulator (HTWOS). The dry blend materials, ordinary portland cement (OPC), Class F fly ash, and ground granulated blast furnace slag (GGBFS or BFS), were obtained from Lafarge North America in Pasco, WA. Over three days, the SCPF was used to fill a 1600 gallon container, staged outside the facility, with simulated Cast Stone grout. The container, staged outside the building approximately 60 ft from the SCPF, was instrumented with x-, y-, and z-axis thermocouples to monitor curing temperature. The container was also fitted with two formed core sampling vials. For the operation, the targeted grout production rate was 1.5 gpm. This required a salt solution flow rate of approximately 1 gpm and a premix feed rate of approximately 580 lb/h. During the final day of operation, the dry feed rate was increased to evaluate the ability of the system to handle increased throughput. Although non-steady state operational periods created free surface liquids, no bleed water was observed either before or after operations. The final surface slope at a fill height of 39.5 inches was 1-1.5 inches across the 8.5 foot diameter container, highest at the final fill point and lowest diametrically opposed to the fill point. During processing, grout was collected in cylindrical containers from both the mixer discharge and the discharge into the container. These samples were stored in a humid environment either in a closed box proximal to the container or inside the laboratory. Additional samples collected at these sampling points

Engineering scale demonstration of a prospective Cast Stone process

Energy Technology Data Exchange (ETDEWEB)

Cozzi, A.; Fowley, M.; Hansen, E.; Fox, K.; Miller, D.; Williams, M.

2014-09-30

This report documents an engineering-scale demonstration with non-radioactive simulants that was performed at SRNL using the Scaled Continuous Processing Facility (SCPF) to fill an 8.5 ft container with simulated Cast Stone grout. The Cast Stone formulation was chosen from the previous screening tests. Legacy salt solution from previous Hanford salt waste testing was adjusted to correspond to the average composition generated from the Hanford Tank Waste Operation Simulator (HTWOS). The dry blend materials, ordinary portland cement (OPC), Class F fly ash, and ground granulated blast furnace slag (GGBFS or BFS), were obtained from Lafarge North America in Pasco, WA. Over three days, the SCPF was used to fill a 1600 gallon container, staged outside the facility, with simulated Cast Stone grout. The container, staged outside the building approximately 60 ft from the SCPF, was instrumented with x-, y-, and z-axis thermocouples to monitor curing temperature. The container was also fitted with two formed core sampling vials. For the operation, the targeted grout production rate was 1.5 gpm. This required a salt solution flow rate of approximately 1 gpm and a premix feed rate of approximately 580 lb/h. During the final day of operation, the dry feed rate was increased to evaluate the ability of the system to handle increased throughput. Although non-steady state operational periods created free surface liquids, no bleed water was observed either before or after operations. The final surface slope at a fill height of 39.5 inches was 1-1.5 inches across the 8.5 foot diameter container, highest at the final fill point and lowest diametrically opposed to the fill point. During processing, grout was collected in cylindrical containers from both the mixer discharge and the discharge into the container. These samples were stored in a humid environment either in a closed box proximal to the container or inside the laboratory. Additional samples collected at these sampling points

Efficacy of Microwave Disinfection on Moist and Dry Dental Stone Casts with Different Irradiation Times

Directory of Open Access Journals (Sweden)

Mahmood Robati Anaraki

2015-07-01

Full Text Available Objectives: Dental practice contains the use of instruments and multiuse items that should be sterilized or disinfected properly. The aim of the current study was to investigate the effect of microwave irradiation on dental stone cast disinfection in moist and dry condition. Materials and Methods: In this in vitro study, 76 stone casts were prepared by a sterile method. The casts were contaminated by Pseudomonas aeruginosa (ATCC 9027, Staphylococcus aureus (ATCC 6538, Enterococcus faecalis (ATCC 29212 as well as Candida albicans (ATCC 10231. Half the samples were dried for two hours and the other half was studied while still moist. The samples were irradiated by a household microwave at 600 W for 3, 5 and 7 minutes. The microorganisms on the samples were extracted by immersion in tryptic soy broth and .001 ml of that was cultured in nutrient agar media, incubated overnight and counted and recorded as colony forming unit per milliliter (CFU/mL. Results: The findings showed that microorganisms reduced to 4.87 logarithm of CFU/mL value on dental cast within seven minutes in comparison with positive control. Although microbial count reduction was observed as a result of exposure time increase, comparison between moist and dried samples showed no significant difference. Conclusions: Seven-minute microwave irradiation at 600 W can effectively reduce the microbial load of dental stone casts. Wetting the casts does not seem to alter the efficacy of irradiation.   Keywords: Microwave Disinfection; Dental Stone Casts; Irradiation Times

Supplemental Immobilization of Hanford Low-Activity Waste: Cast Stone Screening Tests

Energy Technology Data Exchange (ETDEWEB)

Westsik, Joseph H. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Piepel, Gregory F. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lindberg, Michael J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Heasler, Patrick G. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Mercier, Theresa M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Russell, Renee L. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Cozzi, Alex [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Daniel, William E. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Eibling, Russell E. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hansen, E. K. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Reigel, Marissa M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Swanberg, David J. [Washington River Protection Solutions (WRPS), Aiken, SC (United States)

2013-09-30

More than 56 million gallons of radioactive and hazardous waste are stored in 177 underground storage tanks at the U.S. Department of Energy’s (DOE’s) Hanford Site in southeastern Washington State. The Hanford Tank Waste Treatment and Immobilization Plant (WTP) is being constructed to treat the wastes and immobilize them in a glass waste form. The WTP includes a pretreatment facility to separate the wastes into a small volume of high-level waste (HLW) containing most of the radioactivity and a larger volume of low-activity waste (LAW) containing most of the nonradioactive chemicals. The HLW will be converted to glass in the HLW vitrification facility for ultimate disposal at an offsite federal repository. At least a portion (~35%) of the LAW will be converted to glass in the LAW vitrification facility and will be disposed of onsite at the Integrated Disposal Facility (IDF). The pretreatment and HLW vitrification facilities will have the capacity to treat and immobilize the wastes destined for each facility. However, a second LAW immobilization facility will be needed for the expected volume of LAW requiring immobilization. A cementitious waste form known as Cast Stone is being considered to provide the required additional LAW immobilization capacity. The Cast Stone waste form must be acceptable for disposal in the IDF. The Cast Stone waste form and immobilization process must be tested to demonstrate that the final Cast Stone waste form can comply with the waste acceptance criteria for the disposal facility and that the immobilization processes can be controlled to consistently provide an acceptable waste form product. Further, the waste form must be tested to provide the technical basis for understanding the long-term performance of the waste form in the disposal environment. These waste form performance data are needed to support risk assessment and performance assessment (PA) analyses of the long-term environmental impact of the waste disposal in the IDF

Supplemental Immobilization of Hanford Low-Activity Waste: Cast Stone Augmented Formulation Matrix Tests

International Nuclear Information System (INIS)

Cozzi, A.; Crawford, C.; Fox, K.; Hansen, E.; Roberts, K.

2015-01-01

More than 56 million gallons of radioactive and hazardous waste are stored in 177 underground storage tanks at the U.S. Department of Energy's (DOE's) Hanford Site in Washington State. The HLW will be vitrified in the HLW facility for ultimate disposal at an offsite federal repository. A portion (~35%) of the LAW will be vitrified in the LAW vitrification facility for disposal onsite at the Integrated Disposal Facility (IDF). The pretreatment and HLW vitrification facilities will have the capacity to treat and immobilize all of the wastes destined for those facilities. However, a second facility will be needed for the expected volume of LAW requiring immobilization. Cast Stone, a cementitious waste form, is being considered to provide the required additional LAW immobilization capacity. The Cast Stone waste form must be acceptable for disposal in the IDF. The Cast Stone waste form and immobilization process must be tested to demonstrate that the final Cast Stone waste form can comply with the waste acceptance criteria for the disposal facility and that the immobilization processes can be controlled to consistently provide an acceptable waste form product. A testing program was developed in fiscal year (FY) 2012 describing in detail the work needed to develop and qualify Cast Stone as a waste form for the solidification of Hanford LAW. A statistically designed test matrix was used to evaluate the effects of key parameters on the properties of the Cast Stone as it is initially prepared and after curing. For the processing properties, the water-to-dry-blend mix ratio was the most significant parameter in affecting the range of values observed for each property. The single shell tank (SST) Blend simulant also showed differences in measured properties compared to the other three simulants tested. A review of the testing matrix and results indicated that an additional set of tests would be beneficial to improve the understanding of the impacts noted in the

Supplemental Immobilization of Hanford Low-Activity Waste: Cast Stone Augmented Formulation Matrix Tests

Energy Technology Data Exchange (ETDEWEB)

Cozzi, A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Crawford, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Fox, K. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hansen, E. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Roberts, K. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2015-07-20

More than 56 million gallons of radioactive and hazardous waste are stored in 177 underground storage tanks at the U.S. Department of Energy’s (DOE’s) Hanford Site in Washington State. The HLW will be vitrified in the HLW facility for ultimate disposal at an offsite federal repository. A portion (~35%) of the LAW will be vitrified in the LAW vitrification facility for disposal onsite at the Integrated Disposal Facility (IDF). The pretreatment and HLW vitrification facilities will have the capacity to treat and immobilize all of the wastes destined for those facilities. However, a second facility will be needed for the expected volume of LAW requiring immobilization. Cast Stone, a cementitious waste form, is being considered to provide the required additional LAW immobilization capacity. The Cast Stone waste form must be acceptable for disposal in the IDF. The Cast Stone waste form and immobilization process must be tested to demonstrate that the final Cast Stone waste form can comply with the waste acceptance criteria for the disposal facility and that the immobilization processes can be controlled to consistently provide an acceptable waste form product. A testing program was developed in fiscal year (FY) 2012 describing in detail the work needed to develop and qualify Cast Stone as a waste form for the solidification of Hanford LAW. A statistically designed test matrix was used to evaluate the effects of key parameters on the properties of the Cast Stone as it is initially prepared and after curing. For the processing properties, the water-to-dry-blend mix ratio was the most significant parameter in affecting the range of values observed for each property. The single shell tank (SST) Blend simulant also showed differences in measured properties compared to the other three simulants tested. A review of the testing matrix and results indicated that an additional set of tests would be beneficial to improve the understanding of the impacts noted in the Screening

Accuracy of single-abutment digital cast obtained using intraoral and cast scanners.

Science.gov (United States)

Lee, Jae-Jun; Jeong, Ii-Do; Park, Jin-Young; Jeon, Jin-Hun; Kim, Ji-Hwan; Kim, Woong-Chul

2017-02-01

Scanners are frequently used in the fabrication of dental prostheses. However, the accuracy of these scanners is variable, and little information is available. The purpose of this in vitro study was to compare the accuracy of cast scanners with that of intraoral scanners by using different image impression techniques. A poly(methyl methacrylate) master model was fabricated to replicate a maxillary first molar single-abutment tooth model. The master model was scanned with an accurate engineering scanner to obtain a true value (n=1) and with 2 intraoral scanners (CEREC Bluecam and CEREC Omnicam; n=6 each). The cast scanner scanned the master model and duplicated the dental stone cast from the master model (n=6). The trueness and precision of the data were measured using a 3-dimensional analysis program. The Kruskal-Wallis test was used to compare the different sets of scanning data, followed by a post hoc Mann-Whitney U test with a significance level modified by Bonferroni correction (α/6=.0083). The type 1 error level (α) was set at .05. The trueness value (root mean square: mean ±standard deviation) was 17.5 ±1.8 μm for the Bluecam, 13.8 ±1.4 μm for the Omnicam, 17.4 ±1.7 μm for cast scanner 1, and 12.3 ±0.1 μm for cast scanner 2. The differences between the Bluecam and the cast scanner 1 and between the Omnicam and the cast scanner 2 were not statistically significant (P>.0083), but a statistically significant difference was found between all the other pairs (POmnicam, 9.2 ±1.2 μm for cast scanner 1, and 6.9 ±2.6 μm for cast scanner 2. The differences between Bluecam and Omnicam and between Omnicam and cast scanner 1 were not statistically significant (P>.0083), but there was a statistically significant difference between all the other pairs (POmnicam in video image impression had better trueness than a cast scanner but with a similar level of precision. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by

Comparison of dimensional accuracy of digital dental models produced from scanned impressions and scanned stone casts

Science.gov (United States)

Subeihi, Haitham

Introduction: Digital models of dental arches play a more and more important role in dentistry. A digital dental model can be generated by directly scanning intraoral structures, by scanning a conventional impression of oral structures or by scanning a stone cast poured from the conventional impression. An accurate digital scan model is a fundamental part for the fabrication of dental restorations. Aims: 1. To compare the dimensional accuracy of digital dental models produced by scanning of impressions versus scanning of stone casts. 2. To compare the dimensional accuracy of digital dental models produced by scanning of impressions made of three different materials (polyvinyl siloxane, polyether or vinyl polyether silicone). Methods and Materials: This laboratory study included taking addition silicone, polyether and vinyl polyether silicone impressions from an epoxy reference model that was created from an original typodont. Teeth number 28 and 30 on the typodont with a missing tooth number 29 were prepared for a metal-ceramic three-unit fixed dental prosthesis with tooth #29 being a pontic. After tooth preparation, an epoxy resin reference model was fabricated by duplicating the typodont quadrant that included the tooth preparations. From this reference model 12 polyvinyl siloxane impressions, 12 polyether impressions and 12 vinyl polyether silicone impressions were made. All 36 impressions were scanned before pouring them with dental stone. The 36 dental stone casts were, in turn, scanned to produce digital models. A reference digital model was made by scanning the reference model. Six groups of digital models were produced. Three groups were made by scanning of the impressions obtained with the three different materials, the other three groups involved the scanning of the dental casts that resulted from pouring the impressions made with the three different materials. Groups of digital models were compared using Root Mean Squares (RMS) in terms of their

Setting and Stiffening of Cementitious Components in Cast Stone Waste Form for Disposal of Secondary Wastes from the Hanford waste treatment and immobilization plant

Energy Technology Data Exchange (ETDEWEB)

Chung, Chul-Woo; Chun, Jaehun; Um, Wooyong; Sundaram, S. K.; Westsik, Joseph H.

2013-04-01

Cast stone is a cementitious waste form, a viable option to immobilize secondary nuclear liquid wastes generated from Hanford vitrification plant. While the strength and radioactive technetium leaching of different waste form candidates have been reported, no study has been performed to understand the flow and stiffening behavior of Cast Stone, which is essential to ensure the proper workability, especially considering necessary safety as a nuclear waste form in a field scale application. The rheological and ultrasonic wave reflection (UWR) measurements were used to understand the setting and stiffening Cast Stone batches. X-ray diffraction (XRD) was used to find the correlation between specific phase formation and the stiffening of the paste. Our results showed good correlation between rheological properties of the fresh Cast Stone mixture and phase formation during hydration of Cast Stone. Secondary gypsum formation originating from blast furnace slag was observed in Cast Stone made with low concentration simulants. The formation of gypsum was suppressed in high concentration simulants. It was found that the stiffening of Cast Stone was strongly dependent on the concentration of simulant. A threshold concentration for the drastic change in stiffening was found at 1.56 M Na concentration.

Setting and stiffening of cementitious components in Cast Stone waste form for disposal of secondary wastes from the Hanford waste treatment and immobilization plant

Energy Technology Data Exchange (ETDEWEB)

Chung, Chul-Woo; Chun, Jaehun, E-mail: jaehun.chun@pnnl.gov; Um, Wooyong; Sundaram, S.K.; Westsik, Joseph H.

2013-04-01

Cast Stone is a cementitious waste form, a viable option to immobilize secondary nuclear liquid wastes generated from the Hanford Waste Treatment and Immobilization Plant. However, no study has been performed to understand the flow and stiffening behavior, which is essential to ensure proper workability and is important to safety in a nuclear waste field-scale application. X-ray diffraction, rheology, and ultrasonic wave reflection methods were used to understand the specific phase formation and stiffening of Cast Stone. Our results showed a good correlation between rheological properties of the fresh mixture and phase formation in Cast Stone. Secondary gypsum formation was observed with low concentration simulants, and the formation of gypsum was suppressed in high concentration simulants. A threshold concentration for the drastic change in stiffening was found at 1.56 M Na concentration. It was found that the stiffening of Cast Stone was strongly dependent on the concentration of simulant. Highlights: • A combination of XRD, UWR, and rheology gives a better understanding of Cast Stone. • Stiffening of Cast Stone was strongly dependent on the concentration of simulant. • A drastic change in stiffening of Cast Stone was found at 1.56 M Na concentration.

Analysis of Monolith Cores from an Engineering Scale Demonstration of a Prospective Cast Stone Process

International Nuclear Information System (INIS)

Crawford, C. L.; Cozzi, A. D.; Hill, K. A.

2016-01-01

The primary disposition path of Low Activity Waste (LAW) at the DOE Hanford Site is vitrification. A cementitious waste form is one of the alternatives being considered for the supplemental immobilization of the LAW that will not be treated by the primary vitrification facility. Washington River Protection Solutions (WRPS) has been directed to generate and collect data on cementitious or pozzolanic waste forms such as Cast Stone. This report documents the coring and leach testing of monolithic samples cored from an engineering-scale demonstration (ES Demo) with non-radioactive simulants. The ES Demo was performed at SRNL in October of 2013 using the Scaled Continuous Processing Facility (SCPF) to fill an 8.5 ft. diameter x 3.25 ft. high container with simulated Cast Stone grout. The Cast Stone formulation was chosen from the previous screening tests. Legacy salt solution from previous Hanford salt waste testing was adjusted to correspond to the average LAW composition generated from the Hanford Tank Waste Operation Simulator (HTWOS). The dry blend materials, ordinary portland cement (OPC), Class F fly ash, and ground granulated blast furnace slag (GGBFS or BFS), were obtained from Lafarge North America in Pasco, WA. In 2014 core samples originally obtained approximately six months after filling the ES Demo were tested along with bench scale molded samples that were collected during the original pour. A latter set of core samples were obtained in late March of 2015, eighteen months after completion of the original ES Demo. Core samples were obtained using a 2'' diameter x 11'' long coring bit. The ES Demo was sampled in three different regions consisting of an outer ring, a middle ring and an inner core zone. Cores from these three lateral zones were further segregated into upper, middle and lower vertical segments. Monolithic core samples were tested using the Environmental Protection Agency (EPA) Method 1315, which is designed to provide mass

Bainite obtaining in cast iron with carbides castings

Directory of Open Access Journals (Sweden)

S. Pietrowski

2010-01-01

Full Text Available In these paper the possibility of upper and lower bainite obtaining in cast iron with carbides castings are presented. Conditions, when in cast iron with carbides castings during continuous free air cooling austenite transformation to upper bainite or its mixture with lower bainte proceeds, have been given. A mechanism of this transformation has been given, Si, Ni, Mn and Mo distribution in the eutectic cell has been tested and hardness of tested castings has been determined.

Extended Leach Testing of Simulated LAW Cast Stone Monoliths

Energy Technology Data Exchange (ETDEWEB)

Serne, R. Jeffrey [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lanigan, David C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Westsik, Joseph H. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Williams, Benjamin D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Jung, H. B. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wang, Guohui [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-08-12

This revision to the original report adds two longer term leach sets of data to the report and provides more discussion and graphics on how to interpret the results from long-term laboratory leach tests. The leach tests were performed at Pacific Northwest National Laboratory (PNNL) for Washington River Protection Solutions (WRPS) to evaluate the release of key constituents from monoliths of Cast Stone prepared with four simulated low-activity waste (LAW) liquid waste streams.

Position Accuracy of Implant Analogs on 3D Printed Polymer versus Conventional Dental Stone Casts Measured Using a Coordinate Measuring Machine.

Science.gov (United States)

Revilla-León, Marta; Gonzalez-Martín, Óscar; Pérez López, Javier; Sánchez-Rubio, José Luis; Özcan, Mutlu

2017-11-17

To compare the accuracy of implant analog positions on complete edentulous maxillary casts made of either dental stone or additive manufactured polymers using a coordinate measuring machine (CMM). A completely edentulous maxillary model of a patient with 7 implant analogs was obtained. From this model, two types of casts were duplicated, namely conventional dental stone (CDS) using a custom tray impression technique after splinting (N = 5) and polymer cast using additive manufacturing based on the STL file generated. Polymer casts (N = 20; n = 5 per group) were fabricated using 4 different additive manufacturing technologies (multijet printing-MJP1, direct light processing-DLP, stereolithography-SLA, multijet printing-MJP2). CMM was used to measure the correct position of each implant, and distortion was calculated for each system at x-, y-, and z-axes. Measurements were repeated 3 times per specimen in each axis yielding a total of 546 measurements. Data were analyzed using ANOVA, Sheffé tests, and Bonferroni correction (α = 0.05). Compared to CMM, the mean distortion (μm) ranged from 22.7 to 74.9, 23.4 to 49.1, and 11.0 to 85.8 in the x-, y-, and z-axes, respectively. CDS method (x-axis: 37.1; z-axis: 27.62) showed a significant difference compared to DLP on the x-axis (22.7) (p = 0.037) and to MJP1 on the z-axis (11.0) (p = 0.003). Regardless of the cast system, x-axes showed more distortion (42.6) compared to y- (34.6) and z-axes (35.97). Among additive manufacturing technologies, MJP2 presented the highest (64.3 ± 83.6), and MJP1 (21.57 ± 16.3) and DLP (27.07 ± 20.23) the lowest distortion, which was not significantly different from CDS (32.3 ± 22.73) (p > 0.05). For the fabrication of the definitive casts for implant prostheses, one of the multijet printing systems and direct light processing additive manufacturing technologies showed similar results to conventional dental stone. Conventional dental stone casts could be accurately duplicated using some

Properties Improvement of Cast Stone Produced Using Recycled Glass Waste and Lightweight Aggregates

Directory of Open Access Journals (Sweden)

Elham Abd AL-Majeed

2018-01-01

Full Text Available Cast stone (CS is a form of pre-cast concrete widely, used in architectural applications for decorating and building face in place of natural stone due its superior features. The present study was an attempt in using of local lightweight aggregate materials (LWAM as an alternative to percentage of coarse aggregate, and glass wastes as alternatives to percentages of fine aggregate in cast stone normal mixtures with white cement and plasticizer admixture. The CS products were cured after 24 hrs using of two different processes: water curing (at 23 C° for 3 days and steam curing (at 60 C° for 14 hrs. Then the products were characterized by tests of compressive strength, design, absorption, flexure strength and liner drying shrinkage. The addition of alternative materials was done by trial mixes (M0-M3 through 3 groups (A, B, and C according to standards. Group A: design of reference mixtures of CS with compressive strength of 46.3 MPa and the absorption of 6.19%, Group B: design of mixtures containing 50% LWA were 16% lighter than those of Group A with compressive strength of 43.6 MPa and 11% improvement in the absorption, Group C: design of mixtures containing (50 and 75% glass waste with compressive strength of (47.5-44.3 MPa and the absorption of (5.3-4.7%, respectively. The modified steam curing process (curing after 24 hrs casting done in this study could prove its effectiveness in the achievement of the required compressive strength in comparison with the normal process (direct curing after casting due to the effect of such new process in providing the more uniform distribution of the cement gel with good physical properties. Results from the flexural strength test could prove the achievement of the required levels (6.9 – 6.3 at 50 – 75% glass waste addition recorded in the standard.

Assessment of Influence of Contact Time between Alginate and Type III Dental Stone on Properties of Cast Model: An in vitro Study.

Science.gov (United States)

Dev, Shruti; Kar, Aswini K; Garhnayak, Mirna; Garhnayak, Lokanath; Dhal, Angurbala

2017-10-01

Alginate is a versatile, irreversible hydrocolloid impression material, which is cost-effective and forms an essential component in dental practice. For elevating the hardness of the cast models, hardeners are combined with stone. Hence, we planned the present study to evaluate the impact of altering the time of contact between alginate and stone after various interim periods. The present study included the assessment of impact of time of contact between alginate and stone by the construction of 90 casts using a cylinder model. Two bisecting lines were marked and were named as y and y'. These lines were used for testing the dimensional stability. Using chemically cured acrylic resin, the construction of ten special trays was done. All the impression casts were randomly divided into two study groups, with 45 casts in each group-group I: control group, casts were removed after 60 minutes; group II: study group, casts were removed after 9 hours. A digital caliper was used for measuring the dimensional stability of the cast. All the data were collected and analyzed. In the specimens of the control group (group I) and the study group (group II), the mean dimensions from y to y' were found to be 17.54 and 17.95 respectively. The mean reading of hardness in the control group and study group was found to be 0.59 and 0.20 respectively. In groups I and II, the number of specimens showing clarity of two lines (X and X") was 0 and 5 respectively. There was no change in the dimensional stability of the dental stone model when the contact time was increased. Within certain limits, the contact time between alginate and stone can be altered without significantly altering the properties of the cast.

[Cervical adaptation of complete cast crowns of various metal alloys, with and without die spacers].

Science.gov (United States)

Stephano, C B; Roselino, R F; Roselino, R B; Campos, G M

1989-01-01

A metallic replica from a dental preparation for crown was used to make 8 class-IV stone dies. The wax patterns for the casting of the crowns were obtained in two conditions: a) from the stone die with no spacer; and b) from the stone die with an acrylic spacer. Thus, 64 metallic crowns were casted, using 4 different alloys: DURACAST (Cu-Al), NICROCAST (Ni-Cr) and DURABOND (Ni-Cr), and gold. The casted crowns were fitted in the metallic replica and measured as to the cervical discrepance of fitting. The results showed that the use of die spacers decreases the clinical discrepancies of fitting of the casted crowns (in a statistically significant level), no matter the metallic alloy employed.

Analysis of Hanford Cast Stone Supplemental LAW using Composition Adjusted SRS Tank 50 Salt Solution

Energy Technology Data Exchange (ETDEWEB)

Crawford, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Cozzi, A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hill, K. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Ramsey, A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2017-04-25

Vitrification is the primary disposition path for Low Activity Waste (LAW) at the Department of Energy (DOE) Hanford Site. A cementitious waste form is one of the alternatives being considered for the supplemental immobilization of the LAW that will not be treated by the primary vitrification facility. Washington River Protection Solutions (WRPS) has been directed to generate and collect data on cementitious or pozzolanic waste forms such as Cast Stone.

Effect of Repeated Microwave Disinfection on Surface Hardness and Dimensional Accuracy of Two Dental Stone Materials

Directory of Open Access Journals (Sweden)

Mahmood Robati Anaraki

2015-01-01

Full Text Available There is controversial evidence in relation to the effect of microwave on mechanical properties of stone casts. The present study was designed to evaluate the effect of repeated microwave disinfection on surface hardness and dimensional accuracy of dental stone. In this in vitro study, 48 cylindrical stone samples were prepared using two products of type IV stone to assess surface hardness and 48 impressions were taken from a model and poured by these stones to assess the dimensional accuracy. The evaluation of the samples was carried out consequently by a micro-hardness tester and a digital caliper after the stone samples were exposed to 7 consecutive rounds of 900 watts (W microwave irradiation for five minutes each time after cooling. Data were analyzed by t-test and ANOVA. According to the obtained results, multiple disinfections of the stone casts by microwave do not negatively affect their surface hardness and dimensional accuracy.   Key words: Dental stone; Dimensional accuracy; Hardness; Microwave

The sort of carburization and the quality of obtained cast iron

Directory of Open Access Journals (Sweden)

K. Janerka

2008-12-01

Full Text Available In the production of cast iron, the pig iron’s amount in charge material is more and more often limited, and replaced by steel scrap. That extorts the necessity of know-how the carburization and one is looking for carburizers, which ensure obtaining big carbon increment as quickly as possible with the high repeatability and the ones which ensure getting the adequate quality of cast iron. The object of presented research was definition of the influence of charge materials’ sort on the structure, course of solidification, and the effectiveness of process. The cast iron melts, which are presented below, are made only on the basis of steel scrap with portion of graphitoidal, coke and anthracite carburizers, which were added to the charge in solid. In the article one compared the carburizers in respect of their structure, chemical constitution and the effectiveness obtained during the carburization of liquid metal. The melting of cast iron, based on the special pig iron, was carried out as well. The course of melts, chemical constitution of obtained cast iron and its structure were presented. The comparison between quality distribution and the volume fraction of graphite in classes of size for the individual melts were achieved and the TDA curves were inserted.

Technical Approach for Determining Key Parameters Needed for Modeling the Performance of Cast Stone for the Integrated Disposal Facility Performance Assessment

Energy Technology Data Exchange (ETDEWEB)

Yabusaki, Steven B. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Serne, R. Jeffrey [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Rockhold, Mark L. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wang, Guohui [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Westsik, Joseph H. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-03-30

Washington River Protection Solutions (WRPS) and its contractors at Pacific Northwest National Laboratory (PNNL) and Savannah River National Laboratory (SRNL) are conducting a development program to develop / refine the cementitious waste form for the wastes treated at the ETF and to provide the data needed to support the IDF PA. This technical approach document is intended to provide guidance to the cementitious waste form development program with respect to the waste form characterization and testing information needed to support the IDF PA. At the time of the preparation of this technical approach document, the IDF PA effort is just getting started and the approach to analyze the performance of the cementitious waste form has not been determined. Therefore, this document looks at a number of different approaches for evaluating the waste form performance and describes the testing needed to provide data for each approach. Though the approach addresses a cementitious secondary aqueous waste form, it is applicable to other waste forms such as Cast Stone for supplemental immobilization of Hanford LAW. The performance of Cast Stone as a physical and chemical barrier to the release of contaminants of concern (COCs) from solidification of Hanford liquid low activity waste (LAW) and secondary wastes processed through the Effluent Treatment Facility (ETF) is of critical importance to the Hanford Integrated Disposal Facility (IDF) total system performance assessment (TSPA). The effectiveness of cementitious waste forms as a barrier to COC release is expected to evolve with time. PA modeling must therefore anticipate and address processes, properties, and conditions that alter the physical and chemical controls on COC transport in the cementitious waste forms over time. Most organizations responsible for disposal facility operation and their regulators support an iterative hierarchical safety/performance assessment approach with a general philosophy that modeling provides

Effect of Microwave Disinfection on Compressive and Tensile Strengths of Dental Stones

Directory of Open Access Journals (Sweden)

Mahmood Robati Anaraki

2013-03-01

Full Text Available Background and aims. Although microwave irradiation has been used for disinfection of dental stone casts, there are concerns regarding mechanical damage to casts during the process. The aim of this study was to evaluate the effect of microwave irradiation on the compressive strength (CS and diametral tensile strength (DTS of stone casts. Materials and methods. In this in vitro study, 80 cylindrical type III and IV stone models (20 × 40 mm were prepared and divided into 8 groups of 10. The DTS and CS of the specimens were measured by a mechanical testing machine at a crosshead speed of 0.5 cm/min after 7 times of frequent wetting, irradiating at an energy level of 600 W for 3 minutes and cooling. Data were analyzed by Student’s t-test. Results. Microwave irradiation significantly increased DTS of type III and IV to 5.23 ± 0.64 and 8.17 ± 0.94, respectively (P < 0.01. Conclusion. According to the results, microwave disinfection increases DTS of type III and IV stone casts without any effects on their CS.

A comparative evaluation of the marginal adaptation of a thermoplastic resin, a light cured wax and an inlay casting wax on stone dies: An in vitro study.

Science.gov (United States)

Gopalan, Reji P; Nair, Vivek V; Harshakumar, K; Ravichandran, R; Lylajam, S; Viswambaran, Prasanth

2018-01-01

Different pattern materials do not produce copings with satisfactory, marginal accuracy when used on stone dies at varying time intervals. The purpose of this study was to evaluate and compare the vertical marginal accuracy of patterns formed from three materials, namely, thermoplastic resin, light cured wax and inlay casting wax at three-time intervals of 1, 12, and 24 h. A master die (zirconia abutment mimicking a prepared permanent maxillary central incisor) and metal sleeve (direct metal laser sintering crown #11) were fabricated. A total of 30 stone dies were obtained from the master die. Ten patterns were made each from the three materials and stored off the die at room temperature. The vertical marginal gaps were measured using digital microscope at 1, 12, and 24 h after reseating with gentle finger pressure. The results revealed a significant statistical difference in the marginal adaptation of three materials at all the three-time intervals. Light cured wax was found to be most accurate at all time intervals, followed by thermoplastic resin and inlay casting wax. Furthermore, there was a significant difference between all pairs of materials. The change in vertical marginal gap from 1 to 24 h between thermoplastic resin and light cured wax was not statistically significant. The marginal adaptation of all the three materials used, was well within the acceptable range of 25-70 μm. The resin pattern materials studied revealed significantly less dimensional change than inlay casting wax on storage at 1, 12, and 24 h time intervals. They may be employed in situations where high precision and delayed investing is expected.

Generation and evaluation of 3D digital casts of maxillary defects based on multisource data registration: A pilot clinical study.

Science.gov (United States)

Ye, Hongqiang; Ma, Qijun; Hou, Yuezhong; Li, Man; Zhou, Yongsheng

2017-12-01

Digital techniques are not clinically applied for 1-piece maxillary prostheses containing an obturator and removable partial denture retained by the remaining teeth because of the difficulty in obtaining sufficiently accurate 3-dimensional (3D) images. The purpose of this pilot clinical study was to generate 3D digital casts of maxillary defects, including the defective region and the maxillary dentition, based on multisource data registration and to evaluate their effectiveness. Twelve participants with maxillary defects were selected. The maxillofacial region was scanned with spiral computer tomography (CT), and the maxillary arch and palate were scanned using an intraoral optical scanner. The 3D images from the CT and intraoral scanner were registered and merged to form a 3D digital cast of the maxillary defect containing the anatomic structures needed for the maxillary prosthesis. This included the defect cavity, maxillary dentition, and palate. Traditional silicone impressions were also made, and stone casts were poured. The accuracy of the digital cast in comparison with that of the stone cast was evaluated by measuring the distance between 4 anatomic landmarks. Differences and consistencies were assessed using paired Student t tests and the intraclass correlation coefficient (ICC). In 3 participants, physical resin casts were produced by rapid prototyping from digital casts. Based on the resin casts, maxillary prostheses were fabricated by using conventional methods and then evaluated in the participants to assess the clinical applicability of the digital casts. Digital casts of the maxillary defects were generated and contained all the anatomic details needed for the maxillary prosthesis. Comparing the digital and stone casts, a paired Student t test indicated that differences in the linear distances between landmarks were not statistically significant (P>.05). High ICC values (0.977 to 0.998) for the interlandmark distances further indicated the high

Developing technological process of obtaining giality casts

Directory of Open Access Journals (Sweden)

A. Issagulov

2014-10-01

Full Text Available The article considers the process of manufacturing castings using sand-resin forms and alloying furnace. Were the optimal technological parameters of manufacturing shell molds for the manufacture of castings of heating equipment. Using the same upon receipt of castings by casting in shell molds furnace alloying and deoxidation of the metal will provide consumers with quality products and have a positive impact on the economy in general engineering.

Microbiological evaluation of dental stone casts after immersion in sodium hypochlorite and peracetic acid

OpenAIRE

Sekiguchi, Livia Lie Sonoda; São Leopoldo Mandic Institute and Dental Research Center – Campinas – SP – Brazil.; Sekiguchi, Ricardo Takiy; Dental School and University Nove de Julho – São Paulo – SP – Brazil.; Miranda, Milton Edson; São Leopoldo Mandic Institute and Dental Research Center; Basting, Roberta Tarkany; São Leopoldo Mandic Institute and Dental Research Center – Campinas – SP – Brazil.

2016-01-01

Objective: the purpose of this study was to evaluate the efficacy of disinfection of type III dental stone by immersion in 1% sodium hypochlorite and 0.25% peracetic acid at different periods of time (1, 5 and 10 min). MaterialandMethods: silicon dies were previously infected with strains of Bacillus subtilis for 15 min. Then, type III gypsum stone (Herodent, Vigodent COLTÈNE SA, Rio de Janeiro, Brazil) was inserted into the cavities to obtain contaminated specimens. A sterile silicone die wa...

Does 6 Hours of Contact With Alginate Impression Material Affect Dental Cast Properties?

Science.gov (United States)

Ibrahim, Amna Adam; Alhajj, Mohammed Nasser; Khalifa, Nadia; Gilada, Magdi Wadie

2017-06-01

Alginate impression (irreversible hydrocolloid) material is commonly used in dental practice because it is easy to mix, low in cost, and well tolerated by patients. The material is not dimensionally stable, however; thus, it is necessary to pour the impression immediately after the molding is accomplished, or within 60 minutes if the impression is kept in 100% humidity. Excessive contact of the alginate impression with the cast model over time may affect the model's properties. In this study, the authors tested the effect of contact time between an alginate impression and type III dental stone on cast model properties. Sixty-seven cast models were obtained from a stainless steel cylinder by using irreversible hydrocolloid impression material and type III dental stone. Thirty-seven cast models were separated from the impression after 1 hour (control group) and 30 cast models were separated after 6 hours (study group). The samples were evaluated under light microscope for surface details and measured by digital caliper for dimensional stability. An indentation on the cast was made and the depth of the indentation was then measured with a digital caliper to measure hardness. The dimensional stability of the cast models was not affected when contact time was increased from 1 hour to 6 hours (P = .507). Surface details did not deteriorate when contact time was increased, as all of the samples could reproduce all details after the 1-hour and 6-hour interval periods. However, hardness was greater after 1 hour of contact time (P = .001) than after 6 hours of contact time. In conclusion, contact between alginate impression material and type III dental stone up to 6 hours did not affect the dimensional stability and richness of the surface; hardness, though, was significantly affected.

Cast-concrete products made with FBC ash and wet-collected coal-ash

Energy Technology Data Exchange (ETDEWEB)

Naik, T.R.; Kraus, R.N.; Chun, Y.M.; Botha, F.D. [University of Wisconsin, Milwaukee, WI (United States)

2005-12-01

Cast-concrete hollow blocks, solid blocks, and paving stones were produced at a manufacturing plant by replacing up to 45% (by mass) of portland cement with fluidized bed combustion (FBC) coal ash and up to 9% of natural aggregates with wet-collected, low-lime, coarse coal-ash (WA). Cast-concrete product specimens of all three types exceeded the compressive strength requirements of ASTM from early ages, with the exception of one paving-stone mixture, which fell short of the requirement by less than 10%. The cast-concrete products made by replacing up to 40% of cement with FBC ash were equivalent in strength (89-113% of control) to the products without ash. The abrasion resistance of paving stones was equivalent for up to 34% FBC ash content. Partial replacement of aggregates with WA decreased strength of the products. The resistance of hollow blocks and paving stones to freezing and thawing decreased appreciably with increasing ash contents. The cast-concrete products could be used indoors in regions where freezing and thawing is a concern, and outdoors in a moderate climate.

Calcium hypochlorite as a disinfecting additive for dental stone.

Science.gov (United States)

Twomey, Jonathan O; Abdelaziz, Khalid M; Combe, Edward C; Anderson, Dwight L

2003-09-01

Dental casts come into direct contact with impression materials and other items that are contaminated by saliva and blood from a patient's mouth, leaving the casts susceptible to cross-contamination. Topical methods of disinfecting casts are difficult to control, while immersion methods are potentially destructive. Thus, an additional method to control cross-contamination between patients and laboratory personnel is needed. This study was undertaken in an attempt to develop a dental stone with disinfecting properties and adequate compressive and tensile strengths. Calcium hypochlorite [Ca(OCl)(2)] in aqueous solution in concentrations from 0 to 1.5% was tested as a disinfecting additive to type V dental stone. The compressive and tensile strength properties of the modified stone were measured (MPa) using a universal testing machine at a consistency similar to unmodified stone. Strength data were analyzed by 1-way ANOVA and post hoc Tukey-Kramer procedure (alpha CaviCide, and 3 impressions rinsed in water served as controls. In general, the effect of adding the disinfectant to the stone was a decrease in strength. Exceptions were the dry compressive strength, for which there was a significant increase in strength (P=.048) at 0.5%, and the wet compressive and wet tensile strength, which showed no significant difference between the 1.5% and the control. When Ca(OCl)(2) was added at the concentration 0.5% (2765 ppm available chlorine), the gypsum had acceptable mechanical properties; dry compressive strength was 78.86 +/- 4.12 MPa, and dry tensile strength was 10.64 +/- 1.27 MPa, compared to control values of 67.85 +/- 6.28 and 13.41 +/- 1.24 MPa, respectively. At concentrations of 0.3% and higher (36 1650 ppm of available chlorine), calcium hypochlorite was able to completely inactivate phi29. It is possible to prepare a type V dental stone that contains a disinfectant, has adequate mechanical properties, and will reduce numbers of residual microorganisms. For example

Effect of dental technician disparities on the 3-dimensional accuracy of definitive casts.

Science.gov (United States)

Emir, Faruk; Piskin, Bulent; Sipahi, Cumhur

2017-03-01

Studies that evaluated the effect of dental technician disparities on the accuracy of presectioned and postsectioned definitive casts are lacking. The purpose of this in vitro study was to evaluate the accuracy of presectioned and postsectioned definitive casts fabricated by different dental technicians by using a 3-dimensional computer-aided measurement method. An arch-shaped metal master model consisting of 5 abutments resembling prepared mandibular incisors, canines, and first molars and with a 6-degree total angle of convergence was designed and fabricated by computer-aided design and computer-aided manufacturing (CAD-CAM) technology. Complete arch impressions were made (N=110) from the master model, using polyvinyl siloxane (PVS) and delivered to 11 dental technicians. Each technician fabricated 10 definitive casts with dental stone, and the obtained casts were numbered. All casts were sectioned, and removable dies were obtained. The master model and the presectioned and postsectioned definitive casts were digitized with an extraoral scanner, and the virtual master model and virtual presectioned and postsectioned definitive casts were obtained. All definitive casts were compared with the master model by using computer-aided measurements, and the 3-dimensional accuracy of the definitive casts was determined with best fit alignment and represented in color-coded maps. Differences were analyzed using univariate analyses of variance, and the Tukey honest significant differences post hoc tests were used for multiple comparisons (α=.05). The accuracy of presectioned and postsectioned definitive casts was significantly affected by dental technician disparities (Ptechnician differences. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Incorporation of disinfectants for obtaining dental stone: microbiological and dimensional evaluation

Directory of Open Access Journals (Sweden)

Patrícia Lins Azevedo do Nascimento

Full Text Available AIM: To assess dimensional change and antimicrobial activity of disinfectants substances incorporated during the dental stone manipulation. MATERIAL AND METHOD: In vivo - microorganisms were collected in alginate molds of 30 volunteers inoculated on BHI agar and incubated at 37 °C for 24 hours. The molds were cast with type IV gypsum, manipulated with saline (G1, 1% sodium hypochlorite (G2 and 4% chlorhexidine (G3, replacing the water. After setting of plaster with 1 hour two collections on models were made. After 24 hours, the readings were performed. The Kruskal-Wallis and Wilcoxon tests with confidence interval of 99% and 95% respectively were used. In vitro - Müeller Hinton agar petri dishes were inoculated with S. mutans (ATCC25175, S. sanguis (ATCC10556 and E. faecalis (ATCC29212, over which were placed steel rings filled with the same substances of the in vivo study. After deposition of gypsum and incubation, halos were measured with a digital caliper and data were submitted to ANOVA and Tukey's test with confidence interval of 95%. Dimensional Change - With a metallic matrix and a perfectly adapted tray, the insertion axis and force used for moulding and obtain 30 specimens in type IV gypsum were standardized, following the same distribution of the study groups in vivo. The specimens were measured by Image Pro Plus software and data were submitted to ANOVA and Tukey's test with confidence interval of 95%. RESULT: Data from the in vivo study demonstrated a significant difference between the mold and each model (p<0.001. In the Wilcoxon test there was no significant difference between groups of models. At the in vitro test, G2 showed greater inhibition zones in all micro-organisms tested compared to G3, but with respect to dimensional changes, there was a significant difference between solutions and metallic standard, where G3 caused less change than G2. CONCLUSION: Chlorhexidine 4% showed to be the most suitable disinfectant.

Evaluation of marginal and internal gaps of metal ceramic crowns obtained from conventional impressions and casting techniques with those obtained from digital techniques.

Science.gov (United States)

Rai, Rathika; Kumar, S Arun; Prabhu, R; Govindan, Ranjani Thillai; Tanveer, Faiz Mohamed

2017-01-01

Accuracy in fit of cast metal restoration has always remained as one of the primary factors in determining the success of the restoration. A well-fitting restoration needs to be accurate both along its margin and with regard to its internal surface. The aim of the study is to evaluate the marginal fit of metal ceramic crowns obtained by conventional inlay casting wax pattern using conventional impression with the metal ceramic crowns obtained by computer-aided design and computer-aided manufacturing (CAD/CAM) technique using direct and indirect optical scanning. This in vitro study on preformed custom-made stainless steel models with former assembly that resembles prepared tooth surfaces of standardized dimensions comprised three groups: the first group included ten samples of metal ceramic crowns fabricated with conventional technique, the second group included CAD/CAM-milled direct metal laser sintering (DMLS) crowns using indirect scanning, and the third group included DMLS crowns fabricated by direct scanning of the stainless steel model. The vertical marginal gap and the internal gap were evaluated with the stereomicroscope (Zoomstar 4); post hoc Turkey's test was used for statistical analysis. One-way analysis of variance method was used to compare the mean values. Metal ceramic crowns obtained from direct optical scanning showed the least marginal and internal gap when compared to the castings obtained from inlay casting wax and indirect optical scanning. Indirect and direct optical scanning had yielded results within clinically acceptable range.

The Stones and the Stars Building Scotland's Newest Megalith

CERN Document Server

Lunan, Duncan

2013-01-01

There are at least 48 identified prehistoric stone circles in Scotland.  In truth, very little is known about the people who erected them, and ultimately about what the stone circles were for.  Most stone circles are astronomically aligned, which has led to the modern debate over the significance of the alignments.  The megaliths certainly represented an enormous cooperative effort, would at the very least have demonstrated power and wealth, and being set away from any dwellings probably served a ceremonial, or perhaps religious, purpose. Observations at the site of the stone circles, of solar, lunar, and stellar events, have already cast light on some of the questions about the construction and use of ancient megalithic observatories. In his capacity as manager of the Glasgow Parks Department Astronomy Project, author Duncan Lunan designed and built in the late 1970s Sighthill, the first astronomically aligned stone circle in Britain in over 3,000 years.  The Stones and the Stars examines the case for as...

Technetium and Iodine Getters to Improve Cast Stone Performance

Energy Technology Data Exchange (ETDEWEB)

Qafoku, Nikolla [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Neeway, James J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lawter, Amanda R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Levitskaia, Tatiana G. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Serne, R. Jeffrey [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Westsik, Joseph H. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Snyder, Michelle MV [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-02-19

To determine the effectiveness of the various getter materials prior to their solidification in Cast Stone, a series of batch sorption experiments was performed at Pacific Northwest National Laboratory. To quantify the effectiveness of the removal of Tc(VII) and I(I) from solution by getters, the distribution coefficient, K_d (mL/g), was calculated. Testing involved placing getter material in contact with spiked waste solutions at a 1:100 solid-to-solution ratio for periods up to 45 days with periodic solution sampling. One Tc getter was also tested at a 1:10 solid-to-solution ratio. Two different solution media, 18.2 MΩ deionized water (DI H₂O) and a 7.8 M Na LAW simulant, were used in the batch sorption tests. Each test was conducted at room temperature in an anoxic chamber containing N2 with a small amount of H₂ (0.7%) to maintain anoxic conditions. Each getter-solution combination was run in duplicate. Three Tc- and I-doping concentrations were used separately in aliquots of both the 18.2 MΩ DI H2O and a 7.8 M Na LAW waste simulant. The 1× concentration was developed based on Hanford Tank Waste Operations Simulator (HTWOS) model runs to support the River Protection Project System Plan Revision 6. The other two concentrations were 5× and 10× of the HTWOS values. The Tc and I tests were run separately (i.e., the solutions did not contain both solutes). Sampling of the solid-solution mixtures occurred nominally after 0.2, 1, 3, 6, 9, 12, 15 days and ~35 to 45 days. Seven getter materials were tested for Tc and five materials were tested for I. The seven Tc getters were blast furnace slag 1 (BFS1) (northwest source), BFS2 (southeast source), Sn(II)-treated apatite, Sn(II) chloride, nano tin phosphate, KMS (a potassium-metal-sulfide), and tin hydroxapatite. The five iodine getters were layered bismuth hydroxide (LBH), argentite mineral, synthetic argentite, silver-treated carbon, and silver-treated zeolite. The Tc Kd values

Technetium and Iodine Getters to Improve Cast Stone Performance

Energy Technology Data Exchange (ETDEWEB)

Qafoku, Nikolla; Neeway, James J.; Lawter, Amanda R.; Levitskaia, Tatiana G.; Serne, R. Jeffrey; Westsik, Joseph H.; Snyder, Michelle MV

2014-07-01

To determine the effectiveness of the various getter materials prior to their solidification in Cast Stone, a series of batch sorption experiments was performed at Pacific Northwest National Laboratory. To quantify the effectiveness of the removal of Tc(VII) and I(I) from solution by getters, the distribution coefficient, Kd (mL/g), was calculated. Testing involved placing getter material in contact with spiked waste solutions at a 1:100 solid-to-solution ratio for periods up to 45 days with periodic solution sampling. One Tc getter was also tested at a 1:10 solid-to-solution ratio. Two different solution media, 18.2 MΩ deionized water (DI H2O) and a 7.8 M Na LAW simulant, were used in the batch sorption tests. Each test was conducted at room temperature in an anoxic chamber containing N2 with a small amount of H2 (0.7%) to maintain anoxic conditions. Each getter-solution combination was run in duplicate. Three Tc- and I-doping concentrations were used separately in aliquots of both the 18.2 MΩ DI H2O and a 7.8 M Na LAW waste simulant. The 1× concentration was developed based on Hanford Tank Waste Operations Simulator (HTWOS) model runs to support the River Protection Project System Plan Revision 6. The other two concentrations were 5× and 10× of the HTWOS values. The Tc and I tests were run separately (i.e., the solutions did not contain both solutes). Sampling of the solid-solution mixtures occurred nominally after 0.2, 1, 3, 6, 9, 12, 15 days and ~35 to 45 days. Seven getter materials were tested for Tc and five materials were tested for I. The seven Tc getters were blast furnace slag 1 (BFS1) (northwest source), BFS2 (southeast source), Sn(II)-treated apatite, Sn(II) chloride, nano tin phosphate, KMS (a potassium-metal-sulfide), and tin hydroxapatite. The five iodine getters were layered bismuth hydroxide (LBH), argentite mineral, synthetic argentite, silver-treated carbon, and silver-treated zeolite. The Tc Kd values measured from experiments conducted

Evaluation of marginal and internal gaps of metal ceramic crowns obtained from conventional impressions and casting techniques with those obtained from digital techniques

Directory of Open Access Journals (Sweden)

Rathika Rai

2017-01-01

Full Text Available Background: Accuracy in fit of cast metal restoration has always remained as one of the primary factors in determining the success of the restoration. A well-fitting restoration needs to be accurate both along its margin and with regard to its internal surface. Aim: The aim of the study is to evaluate the marginal fit of metal ceramic crowns obtained by conventional inlay casting wax pattern using conventional impression with the metal ceramic crowns obtained by computer-aided design and computer-aided manufacturing (CAD/CAM technique using direct and indirect optical scanning. Materials and Methods: This in vitro study on preformed custom-made stainless steel models with former assembly that resembles prepared tooth surfaces of standardized dimensions comprised three groups: the first group included ten samples of metal ceramic crowns fabricated with conventional technique, the second group included CAD/CAM-milled direct metal laser sintering (DMLS crowns using indirect scanning, and the third group included DMLS crowns fabricated by direct scanning of the stainless steel model. The vertical marginal gap and the internal gap were evaluated with the stereomicroscope (Zoomstar 4; post hoc Turkey's test was used for statistical analysis. One-way analysis of variance method was used to compare the mean values. Results and Conclusion: Metal ceramic crowns obtained from direct optical scanning showed the least marginal and internal gap when compared to the castings obtained from inlay casting wax and indirect optical scanning. Indirect and direct optical scanning had yielded results within clinically acceptable range.

Physical properties and compatibility with dental stones of current alginate impression materials.

Science.gov (United States)

Murata, H; Kawamura, M; Hamada, T; Chimori, H; Nikawa, H

2004-11-01

This study examined physical properties and compatibility with dental stones of two types of alginate impression materials. Five powder-type alginate impression materials (Alginoplast EM, Aroma Fine, Algiace Z, Coe Alginate, Jeltrate Plus) and a paste-type alginate impression material (Tokuso AP-1) were used. The dynamic viscosity immediately after mixing was measured by means of a controlled-stress rheometer. The gelation times were determined according to Japanese Industrial Standards (JIS) T6505, and recovery from deformation, strain in compression and compressive strength were determined according to the International Organization for Standardization (ISO) specification 1563. Detail reproduction and surface roughness of type III dental stones (New Plastone, New Sunstone) and a type IV dental stone (Die Stone) were evaluated using a ruled test block as specified in the ISO specification 1563 and a profilometer, respectively. The alginate impression materials evaluated in this study were all in compliance with the ISO specification 1563 and JIS T6505. The alginate impression materials had similar mechanical properties after gelation, whilst a wide range of dynamic viscosity immediately after being mixed, gelation times and compatibility with dental stones were found among the materials. The paste-type material had a higher dynamic viscosity and a shorter gelation time than the powder-type materials. The best surface quality was obtained with the paste-type material/type III dental stone cast combinations. The materials should be selected in consideration of initial flow, setting characteristics and compatibility with dental stones. The results suggested that a paste-type material would better meet the requirements of an alginate impression material.

Possibilities of obtaining and controlling high-quality pressure castings

Directory of Open Access Journals (Sweden)

S. Pietrowski

2011-07-01

Full Text Available The paper presents the influence of the type of furnace charging melting, refining and modification silumins 226 and 231 on the porosity and microstructure of castings. It was shown that in order to reduce or eliminate the porosity of the castings is necessary to the refining ECOSAL-AL113 of liquid silumin both in the melting furnace, and in the ladle and an additional nitrogen, in the heat furnace modified and refining with nitrogen. To control the effects of refining and modifying the TDA method was used. It was found that based on crystal- lization curve can be qualitatively assess the gas porosity of the castings. In order to control and quality control silumins author developed a computer program using the method of TDA, which sets out: Rm, A5, HB and casting porosity P and the concentration of hydrogen in them. The program also informs the technological procedures to be performed for liquid silumin improper preparation.

The evaluation of working casts prepared from digital impressions.

Science.gov (United States)

Hwang, Y C; Park, Y S; Kim, H K; Hong, Y S; Ahn, J S; Ryu, J J

2013-01-01

The aim of this study is to evaluate the reproducibility of working casts of a digital impression system by comparing them with the original, virtual, and rapid prototyping casts. A total of 54 cast sets in clinically stable occlusion were used. They were scanned by an iTero intraoral scanner and converted into STL format virtual casts. Rapid prototyping casts and polyurethane casts were fabricated from the iTero milling system based on the virtual casts. Several horizontal and vertical measurements were performed from the four types of casts, that is, original stone casts, virtual casts, rapid prototyping casts, and polyurethane casts of iTero. Measurement error, intraclass correlation coefficient (ICC), and differences among the casts were calculated and compared. Casts from iTero milling machines exhibited greater dimensional differences and lower ICC values than did other casts. In addition, many of the measurements of the iTero working casts showed statistically significant differences in comparison to the three other types of casts. In contrast, there were no statistically significant differences between the virtual and original casts. Virtual casts made by the iTero intraoral scanner exhibited excellent reproducibility. However, the casts from the iTero milling machine showed greater dimensional differences and lower reproducibility compared to other types of casts.

Evaluation of compatible mortars to repair 19th century natural cement cast stone from the French Rhône-Alpes region

Directory of Open Access Journals (Sweden)

Myriam Bouichou

2008-01-01

Full Text Available In France, natural cements were extensively produced in the middle of the 19th century. In the French Alps, due to their ochre color, these cements were massively used, notably to produce cast stone, to simulate natural freestone. A preliminary survey revealed an overall good state of preservation of the buildings of this period. Two kinds of decays mechanisms were however identified : erosion affecting the surface of the majority of the buildings, inducing a gradual disappearance of the initial "fake-stone aspect", and a spalling phenomenon often combined with salts crystallization, observed only on a few buildings. Today, due to a lack of appropriate repair materials, the rehabilitation of these buildings mainly consists in the use of gray Portland-cement-based-mortars combined with a painting finishing, which is not satisfactory considering the conservation deontology, as the original appearance is lost. Therefore, the aim of this project was to develop and to test compatible repair materials to restore the culture heritage of this region. Based on the preliminary characterization of a set of representative ancient buildings, combined to a literature review, specifications concerning the composition and the main properties of repair materials, which could assure a compatibility with the ancient concrete of the region were established. Then, three Prompt-cement and one Portland-cement based mortars were selected, two of them being specifically formulated. Firstly, the appearance, the workability and the mechanical and physical properties of those mortars were characterized. Secondly, to evaluate the compatibility of the selected mortars with ancient concrete, Prompt-cement-based slabs were cast using a 19th century concrete formula, and were artificially eroded. After applying the 4 mortars on the slabs, visual observations and pull-out tests will be carried out before and after artificial aging. Finally, the repair mortar presenting the best

Control of cast iron and casts manufacturing by Inmold method

Directory of Open Access Journals (Sweden)

S. Pietrowski

2009-07-01

Full Text Available In this paper the usability of cast iron spheroidizing process in mould control by ATD method as well as by ultrasonic method were presented. Structure of instrumentation needed for control form performance of cast iron spheroidizing by Inmold method was illustrated. Author, pointed out that amount of magnesium master alloy should obtain 0,8 ÷ 1,0% of mass in form at all. Such quantity of preliminary alloy assure of obtain of nodular graphite in cast iron. In consequence of this, is reduce the cast iron liquidus temperature and decrease of recalescence temperature of graphite-eutectic crystallization in compare with initial cast iron. Control of casts can be carried out by ultrasonic method. In plain cast iron, ferritic-pearlitic microstructure is obtaining. Additives of 1,5% Cu ensure pearlitic structure.

Assessment of the Cast Stone Low-Temperature Waste Form Technology Coupled with Technetium Removal - 14379

Energy Technology Data Exchange (ETDEWEB)

Brown, Christopher F.; Rapko, Brian M.; Serne, R. Jeffrey; Westsik, Joseph H.; Cozzi, Alex; Fox, Kevin M.; Mccabe, Daniel J.; Nash, C. A.; Wilmarth, William R.

2014-03-03

The U.S. Department of Energy Office of Environmental Management (EM) is engaging the national laboratories to provide the scientific and technological rigor to support EM program and project planning, technology development and deployment, project execution, and assessment of program outcomes. As an early demonstration of this new responsibility, Pacific Northwest National Laboratory (PNNL) and Savannah River National Laboratory (SRNL) were chartered to implement a science and technology program addressing low-temperature waste forms for immobilization of DOE aqueous waste streams, including technetium removal as an implementing technology. As a first step, the laboratories examined the technical risks and uncertainties associated with the Cast Stone waste immobilization and technetium removal projects at Hanford. Science and technology gaps were identified for work associated with 1) conducting performance assessments and risk assessments of waste form and disposal system performance, and 2) technetium chemistry in tank wastes and separation of technetium from waste processing streams. Technical approaches to address the science and technology gaps were identified and an initial sequencing priority was suggested. A subset of research was initiated in 2013 to begin addressing the most significant science and technology gaps. The purpose of this paper is to report progress made towards closing these gaps and provide notable highlights of results achieved to date.

Biliary Cast Syndrome: Hepatic Artery Resistance Index, Pathological Changes, Morphology and Endoscopic Therapy

Directory of Open Access Journals (Sweden)

Hu Tian

2015-01-01

Full Text Available Background: Biliary cast syndrome (BCS was a postoperative complication of orthotopic liver transplantation (OLT, and the reason for BSC was considered to relate with ischemic type biliary lesions. This study aimed to evaluate the relationship between BCS following OLT and the hepatic artery resistance index (HARI, and to observe pathological changes and morphology of biliary casts. Methods: Totally, 18 patients were diagnosed with BCS by cholangiography following OLT using choledochoscope or endoscopic retrograde cholangiopancreatography. In addition, 36 patients who did not present with BCS in the corresponding period had detectable postoperative HARI on weeks 1, 2, 3 shown by color Doppler flow imaging. The compositions of biliary casts were analyzed by pathological examination and scanning electron microscopy. Results: HARI values of the BCS group were significantly decreased as compared with the non-BCS group on postoperative weeks 2 and 3 (P 1 (OR = 1.300; 1.223; and 1.889, respectively. The OR of HARI 3 was statistically significant (OR = 1.889; 95% confidence interval = 1.166-7.490; P = 0.024. The compositions of biliary casts were different when bile duct stones were present. Furthermore, vascular epithelial cells were found by pathological examination in biliary casts. Conclusions: HARI may possibly serve as an independent risk factor and early predictive factor of BCS. Components and formation of biliary casts and bile duct stones are different.

Endoscopic Stone Measurement During Ureteroscopy.

Science.gov (United States)

Ludwig, Wesley W; Lim, Sunghwan; Stoianovici, Dan; Matlaga, Brian R

2018-01-01

Currently, stone size cannot be accurately measured while performing flexible ureteroscopy (URS). We developed novel software for ureteroscopic, stone size measurement, and then evaluated its performance. A novel application capable of measuring stone fragment size, based on the known distance of the basket tip in the ureteroscope's visual field, was designed and calibrated in a laboratory setting. Complete URS procedures were recorded and 30 stone fragments were extracted and measured using digital calipers. The novel software program was applied to the recorded URS footage to obtain ureteroscope-derived stone size measurements. These ureteroscope-derived measurements were then compared with the actual-measured fragment size. The median longitudinal and transversal errors were 0.14 mm (95% confidence interval [CI] 0.1, 0.18) and 0.09 mm (95% CI 0.02, 0.15), respectively. The overall software accuracy and precision were 0.17 and 0.15 mm, respectively. The longitudinal and transversal measurements obtained by the software and digital calipers were highly correlated (r = 0.97 and 0.93). Neither stone size nor stone type was correlated with error measurements. This novel method and software reliably measured stone fragment size during URS. The software ultimately has the potential to make URS safer and more efficient.

Evaluation of a 3D stereophotogrammetric technique to measure the stone casts of patients with unilateral cleft lip and palate.

Science.gov (United States)

Sforza, Chiarella; De Menezes, Marcio; Bresciani, Elena; Cerón-Zapata, Ana M; López-Palacio, Ana M; Rodriguez-Ardila, Myriam J; Berrio-Gutiérrez, Lina M

2012-07-01

To assess a three-dimensional stereophotogrammetric method for palatal cast digitization of children with unilateral cleft lip and palate. As part of a collaboration between the University of Milan (Italy) and the University CES of Medellin (Colombia), 96 palatal cast models obtained from neonatal patients with unilateral cleft lip and palate were obtained and digitized using a three-dimensional stereophotogrammetric imaging system. Three-dimensional measurements (cleft width, depth, length) were made separately for the longer and shorter cleft segments on the digital dental cast surface between landmarks, previously marked. Seven linear measurements were computed. Systematic and random errors between operators' tracings, and accuracy on geometric objects of known size were calculated. In addition, mean measurements from three-dimensional stereophotographs were compared statistically with those from direct anthropometry. The three-dimensional method presented good accuracy error ( .05). Statistically significant differences (p digitization with unilateral cleft lip and palate. This would be useful for clinical analyses in maxillofacial, plastic, and aesthetic surgery.

Ductile cast iron obtaining by Inmold method with use of LOST FOAM process

Directory of Open Access Journals (Sweden)

T. Pacyniak

2010-01-01

Full Text Available The possibility of manufacturing of ductile cast iron castings by Inmold method with use of LOST FOAM process was presented in this work. The spheroidization was carried out by magnesium master alloy in amounts of 1% casting mass. Nodulizer was located in the reactive chamber in the gating system made of foamed polystyrene. Pretests showed, that there are technical possibilities of manufacturing of casts from ductile cast iron in the LOST FOAM process with use of spheroidization in mould.

Recurrent cholangitis in the tropics: Worm or cast?

Directory of Open Access Journals (Sweden)

Jain P

2010-01-01

Full Text Available The development of biliary casts is very rare, especially in non-liver transplant patients. The etiology of these casts is uncertain but several factors have been proposed which lead to bile stasis and/or gallbladder hypo-contractility and promote cast formation. Here, we report a 54-year-old male, with diabetes and ischemic heart disease, who presented with recurrent attacks of cholangitis. Magnetic resonance cholangiopancreatography revealed linear T1 hyperintense and T2 hypointense filling defects in the right and left hepatic ducts extending into the common hepatic duct, and a calculus in the lower common bile duct, raising a suspicion of worm in the biliary tree. In view of failed attempts at extraction on endoscopy, patient underwent surgery. At exploration, biliary casts and stones were extracted from the proximal and the second order bile ducts, with the help of intraoperative choledochoscopy and a bilio-enteric anastomosis was accomplished. Although endoscopic retrieval of the biliary cast can be employed as first-line management, surgery should be considered in case it fails.

Physicochemical and Microstructural Characterization of Corn Starch Edible Films Obtained by a Combination of Extrusion Technology and Casting Technique.

Science.gov (United States)

Fitch-Vargas, Perla Rosa; Aguilar-Palazuelos, Ernesto; de Jesús Zazueta-Morales, José; Vega-García, Misael Odín; Valdez-Morales, Jesús Enrique; Martínez-Bustos, Fernando; Jacobo-Valenzuela, Noelia

2016-09-01

Starch edible films (EFs) have been widely studied due to their potential in food preservation; however, their application is limited because of their poor mechanical and barrier properties. Because of that, the aim of this work was to use the extrusion technology (Ex T) as a pretreatment of casting technique to change the starch structure in order to obtain EFs with improved physicochemical properties. To this, corn starch and a mixture of plasticizers (sorbitol and glycerol, in different ratios) were processed in a twin screw extruder to generate the starch modification and subsequently casting technique was used for EFs formation. The best conditions of the Ex T and plasticizers concentration were obtained using response surface methodology. All the response variables evaluated, were affected significatively by the Plasticizers Ratio (Sorbitol:Glycerol) (PR (S:G)) and Extrusion Temperature (ET), while the Screw Speed (SS) did not show significant effect on any of these variables. The optimization study showed that the appropriate conditions to obtain EFs with the best mechanical and barrier properties were ET = 89 °C, SS = 66 rpm and PR (S:G) = 79.7:20.3. Once the best conditions were obtained, the optimal treatment was characterized according to its microstructural properties (X-ray diffraction, Scanning Electron Microscopy and Atomic Force Microscopy) to determine the damage caused in the starch during Ex T and casting technique. In conclusion, with the combination of Ex T and casting technique were obtained EFs with greater breaking strength and deformation, as well as lower water vapor permeability than those reported in the literature. © 2016 Institute of Food Technologists®

Waste Acceptance Testing of Secondary Waste Forms: Cast Stone, Ceramicrete and DuraLith

International Nuclear Information System (INIS)

Mattigod, Shas V.; Westsik, Joseph H.; Chung, Chul-Woo; Lindberg, Michael J.; Parker, Kent E.

2011-01-01

all the waste forms had leachability indices better than the target LI > 9 for technetium; (2) Rhenium diffusivity: Cast Stone 2M specimens, when tested using EPA 1315 protocol, had leachability indices better than the target LI > 9 for technetium based on rhenium as a surrogate for technetium. All other waste forms tested by ANSI/ANS 16.1, ASTM C1308, and EPA 1315 test methods had leachability indices that were below the target LI > 9 for Tc based on rhenium release. These studies indicated that use of Re(VII) as a surrogate for 99Tc(VII) in low temperature secondary waste forms containing reductants will provide overestimated diffusivity values for 99Tc. Therefore, it is not appropriate to use Re as a surrogate 99Tc in future low temperature waste form studies. (3) Iodine diffusivity: ANSI/ANS 16.1, ASTM C1308, and EPA 1315 tests indicated that the three waste forms had leachability indices that were below the target LI > 11 for iodine. Therefore, it may be necessary to use a more effective sequestering material than silver zeolite used in two of the waste forms (Ceramicrete and DuraLith); (4) Sodium diffusivity: All the waste form specimens tested by the three leach methods (ANSI/ANS 16.1, ASTM C1308, and EPA 1315) exceeded the target LI value of 6; (5) All three leach methods (ANS 16.1, ASTM C1308 and EPA 1315) provided similar 99Tc diffusivity values for both short-time transient diffusivity effects as well as long-term (∼90 days) steady diffusivity from each of the three tested waste forms (Cast Stone 2M, Ceramicrete and DuraLith). Therefore, any one of the three methods can be used to determine the contaminant diffusivities from a selected waste form.

Waste Acceptance Testing of Secondary Waste Forms: Cast Stone, Ceramicrete and DuraLith

Energy Technology Data Exchange (ETDEWEB)

Mattigod, Shas V.; Westsik, Joseph H.; Chung, Chul-Woo; Lindberg, Michael J.; Parker, Kent E.

2011-08-12

all the waste forms had leachability indices better than the target LI > 9 for technetium; (2) Rhenium diffusivity: Cast Stone 2M specimens, when tested using EPA 1315 protocol, had leachability indices better than the target LI > 9 for technetium based on rhenium as a surrogate for technetium. All other waste forms tested by ANSI/ANS 16.1, ASTM C1308, and EPA 1315 test methods had leachability indices that were below the target LI > 9 for Tc based on rhenium release. These studies indicated that use of Re(VII) as a surrogate for 99Tc(VII) in low temperature secondary waste forms containing reductants will provide overestimated diffusivity values for 99Tc. Therefore, it is not appropriate to use Re as a surrogate 99Tc in future low temperature waste form studies. (3) Iodine diffusivity: ANSI/ANS 16.1, ASTM C1308, and EPA 1315 tests indicated that the three waste forms had leachability indices that were below the target LI > 11 for iodine. Therefore, it may be necessary to use a more effective sequestering material than silver zeolite used in two of the waste forms (Ceramicrete and DuraLith); (4) Sodium diffusivity: All the waste form specimens tested by the three leach methods (ANSI/ANS 16.1, ASTM C1308, and EPA 1315) exceeded the target LI value of 6; (5) All three leach methods (ANS 16.1, ASTM C1308 and EPA 1315) provided similar 99Tc diffusivity values for both short-time transient diffusivity effects as well as long-term ({approx}90 days) steady diffusivity from each of the three tested waste forms (Cast Stone 2M, Ceramicrete and DuraLith). Therefore, any one of the three methods can be used to determine the contaminant diffusivities from a selected waste form.

Technetium, Iodine, and Chromium Adsorption/Desorption Kd Values for Vadose Zone Pore Water, ILAW Glass, and Cast Stone Leachates Contacting an IDF Sand Sequence

Energy Technology Data Exchange (ETDEWEB)

Last, George V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Snyder, Michelle M.V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Um, Wooyong [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Stephenson, John R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Leavy, Ian I. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Strickland, Christopher E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Bacon, Diana H. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Qafoku, Nikolla [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Serne, R. Jeffrey [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-11-01

Performance and risk assessments of immobilized low-activity waste (ILAW) at the Integrated Disposal Facility (IDF) have shown that risks to groundwater are quite sensitive to adsorption-desorption interactions occurring in the near- and far-field environment. These interactions between the underlying sediments and the contaminants present in the leachates that descend from the buried glass, secondary waste grouts, and potentially Cast Stone low-activity waste packages have been represented in these assessments using the contaminant distribution coefficient (Kd) construct. Some contaminants (99Tc, 129I, and Cr) present in significant quantities in these wastes have low Kd values and tend to drive risk to public health and the environment. Relatively small changes in the Kd value can cause relatively large changes in the retardation factor. Thus, even relatively small uncertainty in the Kd value can result in a relatively large uncertainty in the risk determined through performance assessment modeling. The purpose of this study is to further reduce the uncertainty in Kd values for 99Tc, iodine (iodide and iodate), and Cr (chromate; CrO42-) by conducting systematic adsorption-desorption experiments using actual sand-dominated Hanford formation sediments from beneath the IDF and solutions that closely mimic Hanford vadose zone pore water and leachates from Cast Stone and ILAW glass waste forms. Twenty-four batch and 21 flow-through column experiments were conducted, yielding 261 Kd measurements for these key contaminants, and contributing to our understanding for predicting transport from wastes disposed to the IDF. While the batch Kd methodology is not well-suited for measuring Kd values for non-sorbing species (as noted by the U.S. Environmental Protection Agency), the batch Kd results presented here are not wholly inconsistent with the column Kd results, and could be used for sensitivity purposes. Results from the column experiments are consistent with the best

Aluminium Foam and Magnesium Compound Casting Produced by High-Pressure Die Casting

Directory of Open Access Journals (Sweden)

Iban Vicario

2016-01-01

Full Text Available Nowadays, fuel consumption and carbon dioxide emissions are two of the main focal points in vehicle design, promoting the reduction in the weight of vehicles by using lighter materials. The aim of the work is to evaluate the influence of different aluminium foams and injection parameters in order to obtain compound castings with a compromise between the obtained properties and weight by high-pressure die cast (HPDC using aluminium foams as cores into a magnesium cast part. To evaluate the influence of the different aluminium foams and injection parameters on the final casting products quality, the type and density of the aluminium foam, metal temperature, plunger speed, and multiplication pressure have been varied within a range of suitable values. The obtained compound HPDC castings have been studied by performing visual and RX inspections, obtaining sound composite castings with aluminium foam cores. The presence of an external continuous layer on the foam surface and the correct placement of the foam to support injection conditions permit obtaining good quality parts. A HPDC processed magnesium-aluminium foam composite has been developed for a bicycle application obtaining a suitable combination of mechanical properties and, especially, a reduced weight in the demonstration part.

Evaluation of mechanical properties and microstructural characterization of consolidated Cobalt-Chromium-Molybdenum obtained by selective laser melting and precision casting

International Nuclear Information System (INIS)

Mergulhão, Marcello Vertamatti

2017-01-01

The objective of this work was to study the mechanical properties and microstructural characterization of specimens of the Co-Cr-Mo alloy obtained by additive manufacturing -selective laser melting (SLM) and precision casting aiming at the manufacture of dental prostheses. The following steps were carried out on Co-Cr-Mo gas-atomized powders: 1) investigation of the physical, chemical and thermal properties of atomized powders in different grain sizes (denominated: D1 <15 μm, D2 20-50 μm and D3 > 75 μm); 2) the consolidation of standard specimens via consolidation techniques; 3) characterization of consolidated by analysis of: cytotoxicity, porosity, X ray diffraction and dilatometry; 4) mechanical characterization of tensile, 3 point bending, hardness (macro and micro Vickers) tests and microstructural characterization (optical and scanning electron microscopy). In general, the results observed were: the grain size D2 (20-50 μm) is the one that best fits in the analysis of packaging, for the consolidation by SLM; the biocompatibility of the samples obtained a positive result for both processing techniques; the mechanical evaluation of the specimens shows that the SLM technique provides superior mechanical properties (yield stress, rupture stress, maximum stress, elongation and hardness), compared to those obtained by the precision casting technique; the microstructure obtained by the SLM process results in an ultrafine grains with high chemical homogeneity, differentiated by the gross dendritic microstructure in the casting process. In this way, the development of the present study evidenced superior quality in manufacturing customized dental components (copings) by SLM technique compared to precision casting. (author)

Lessons from a Stone Farm

Science.gov (United States)

Kavanagh, John P.; Rao, P. Nagaraj

2007-04-01

The stone farm is a system for measuring macroscopic stone growth of 12 calcium stones simultaneously. It is based on mixed suspension, mixed product removal continuous crystallization principles and the stones are grown continuously for about 500 hours or more. The growth of the stones follows a surface area dependent pattern and the growth rate constants are very similar irrespective of whether the stating materials are fragments of human stone or pieces of marble chip. Increasing citrate from 2mM to 6mM caused a significant growth inhibition which persisted in the presence of urinary macromolecules. Phytate was a very effective inhibitor (about 50% at sub-μM concentrations) but the effective concentration was increased by an order of magnitude in the presence of urinary macromolecules. The effective concentration for inhibition in a crystallization assay was a further two orders of magnitude higher. Urinary macromolecules or almost whole urine were also strongly inhibitory although neither human serum albumin nor bovine mucin had any great effect. The relationship between the size distribution of crystals in suspension and the stone enlargement rate suggests that the primary enlargement mechanism for these in vitro stones is through aggregation. The stone farm is a powerful tool with which to study crystallization inhibitors in a new light. Some differences between inhibition of crystallization and inhibition of stone growth have emerged and we have obtained quantitative evidence on the mechanism of stone enlargement in vitro. Our findings suggest that the interface between crystals in suspension and the stone surface is the key to controlling stone enlargement.

TECHNOLOGICAL PARAMETERS OF SLUGS CASTING OF GREY CAST IRON BY FROSTING

Directory of Open Access Journals (Sweden)

E. I. Marukovich

2009-01-01

Full Text Available The relation of geometrical parametres of casting with technological ones is shown. The monogram for definition of basic technological parametres of obtaining of castings by the method of continuously-cyclic iterative casting by freezing-up is presented.

Geological-Technical and Geo-engineering Aspects of Dimensional Stone Underground Quarrying

Science.gov (United States)

Fornaro, Mauro; Lovera, Enrico

Underground exploitation of dimensional stones is not a novelty, being long since practised, as proved by a number of historical documents and by a certain number of ancient quarrying voids throughout the world. Anyway, so far, open cast quarrying has been the most adopted practice for the excavation of dimensional stones. One primary reason that led to this situation is of course connected to the lower production costs of an open cast exploitation compared to an underground one. This cheapness has been supported by geological and technical motives: on the one hand, the relative availability of surface deposits and, on the other, the development of technologies, which often can be used only outdoor. But, nowadays, general costs of quarrying activities should be re-evaluated because new, and often proper, restrictions have been strongly rising during recent years. As a consequence of both environmental and technical restrictions, pressure will more and more arise to reduce open cast quarrying and to promote underground exploitations. The trend is already well marked for weak rocks - for instance in the extractive basin of Carrara, where about one hundred quarries are active, 30 per cent is working underground, but also in Spain, Portugal and Greece the number of underground marble quarries is increasing - but not yet for hard rock quarrying, where only few quarries are working underground all around the world. One reason has to be found in cutting technologies traditionally used. In weak rocks, diamond wire saw and chain cutter are usable, with few adaptations, in underground spaces, while drilling and blasting, the traditional exploitation method for hard stone, is not easily usable in a confined space, where often only one free face is available. Many technicians and researchers agree that two technologies will probably open the door to underground quarrying in hard rocks: diamond wire and water jet. The first one is already available; the second should still be

PIXE analysis of chinese chicken-blood stone

International Nuclear Information System (INIS)

Lin, E.K.; Wang, C.W.; Yu, Y.C.; Liu, T.Y.; Cheng, H.S.; Zhu, H.X.; Yang, H.J.

1999-01-01

This paper reports the chemical compositions of chicken-blood stone Ji Xue Shi measured by Proton Induced X-ray Emission (PIXE). The experimental result show that for the red portion of chicken-blood stone, the concentration of Hg is as high as 20 wt%, and the concentration of S can be above 10 wt%. For the non-red portion the main chemical compositions are Al 2 O 3 and SiO 2 . The obtained chemical compositions are close to those of kaolinite for Balin chicken-blood stone, and of pyrophyllite for Changhua chicken-blood stone, respectively. So far many Changhua chicken-blood stones and Balin chicken-blood stones were found in China, the PIXE method can be used to explore the provenance of available chicken-blood stones. (author)

Crushed Stone Operations

Data.gov (United States)

Department of Homeland Security — This map layer includes crushed stone operations in the United States. These data were obtained from information reported voluntarily to the USGS by the aggregate...

Analysis of kidney stones by PIXE and RBS techniques

Energy Technology Data Exchange (ETDEWEB)

Alkofai, M M [Physics Dept., Yarmouk University, Irbid, (Jordan); Hallak, A B [Research Institute, King Fahd University of Petroleum and Minerals, Dhahran 31261, (Saudi Arabia)

1995-10-01

Human kidney stones were analyzed by PIXE and RBS techniques using 2 MeV He{sup ++} beam. The stones were found to contain the elements: C, N, O, F, Na, Mg, Si, P, S, Cl, K, Ca, Fe and Br. Results obtained by PIXE agree with the results obtained by RBS within experimental errors. A Mechanism for the formation of the kidney stones is suggested. 3 figs., 1 tab.

Analysis of kidney stones by PIXE and RBS techniques

International Nuclear Information System (INIS)

Alkofai, M.M.; Hallak, A.B.

1995-01-01

Human kidney stones were analyzed by PIXE and RBS techniques using 2 MeV He ++ beam. The stones were found to contain the elements: C, N, O, F, Na, Mg, Si, P, S, Cl, K, Ca, Fe and Br. Results obtained by PIXE agree with the results obtained by RBS within experimental errors. A Mechanism for the formation of the kidney stones is suggested. 3 figs., 1 tab

A Casting Form from the Muranka Unfortified Site on the Usa River

Directory of Open Access Journals (Sweden)

Stashenkov Dmitry A.

2012-03-01

Full Text Available A new find from Muranka unfortified settlement, one of major Golden Horde period sites in the Middle Volga river region is published. It is a double-sided stone mould intended for casting jewelry. Each side of the form was used for casting individual jewelry items: women's hair, head and costume decorations. The head ornaments include two temple rings and earrings shaped as question marks. One more decorative element, styled as a bird’s figure could be either part of some complex piece or an individual product. The other side of the form was used for casting two product varieties: belt buckles and pendants. The mould is of high-quality workmanship. The exact analogy of this rare find is not yet known.

Piezoelectric extracorporeal lithotripsy of gallbladder stones: New inclusion criteria

Energy Technology Data Exchange (ETDEWEB)

Han, Joon Koo; Choi, Byung Ihn; Shin, Yong Moon; Yoon, Yong Kyu; Yoon, Yong Bum; Park, Yong Hyun; Kim, Chu Wan; Han, Man Chung [Seoul National University College of Medicine, Seoul (Korea, Republic of)

1994-08-15

To establish the optimal inclusion criteria for the patients with gallbladder stones to extracorporeal shock wave lithotripsy(ESWL) by retrospectively analyzed our current results. Data obtained from 201 patients with gallbladder stones treated with ESWL and oral chemolytic agent from November 1988 to July 1992 were retrospectively analyzed. Ninety-six had radiolucent stones and 105 had radiopaque stones. We used piezoelectric lithotriptor(EDAP LT. 01) and there were no limitation in number of sessions or total number of shock waves. ESWL was repeated until the size of the largest fragment is smaller than 4 mm. Follow up ultrasound was done in every three months after the successful fragmentation. Average length of the follow up was 205 days. We analyzed the rate of successful fragmentation, number of shock waves needed to achieve successful fragmentation according to the size, number of stones as well as the presence of the calcification. Stone-free rate after 6 months was also calculated from all subgroups and compared to each other. The rate of successful fragmentation was 76.2% for radiolucent stones and 65.6% for radiopaque stones(p> 0.05) after 46,731 and 56,111 shock wave respectively(p > 0.05) The rate of successful fragmentation was highest in patients with single, radiolucent stone smaller than 2 cm(91.7%) followed by single radiolucent stone larger than 2 cm(83.3%), multiple calcified stones smaller than 2 cm (77.4%) and single calcified stone smaller than 2 cm(72.1%). The rate of complete stone clearance after 6 month follow-up was highest in patients with single radiolucent stone smaller than 2 cm (63.3%) and followed by multiple calcified stones smaller than 2 cm(37.3%), single calcified stone smaller than 2 cm(33.9%)(p < 0.05). To obtain better results with ESWL in patients with gallbladder stone, the authors propose a more strict inclusion criteria, which is the patient with a single, radiolucent stone smaller than 2 cm.

Piezoelectric extracorporeal lithotripsy of gallbladder stones: New inclusion criteria

International Nuclear Information System (INIS)

Han, Joon Koo; Choi, Byung Ihn; Shin, Yong Moon; Yoon, Yong Kyu; Yoon, Yong Bum; Park, Yong Hyun; Kim, Chu Wan; Han, Man Chung

1994-01-01

To establish the optimal inclusion criteria for the patients with gallbladder stones to extracorporeal shock wave lithotripsy(ESWL) by retrospectively analyzed our current results. Data obtained from 201 patients with gallbladder stones treated with ESWL and oral chemolytic agent from November 1988 to July 1992 were retrospectively analyzed. Ninety-six had radiolucent stones and 105 had radiopaque stones. We used piezoelectric lithotriptor(EDAP LT. 01) and there were no limitation in number of sessions or total number of shock waves. ESWL was repeated until the size of the largest fragment is smaller than 4 mm. Follow up ultrasound was done in every three months after the successful fragmentation. Average length of the follow up was 205 days. We analyzed the rate of successful fragmentation, number of shock waves needed to achieve successful fragmentation according to the size, number of stones as well as the presence of the calcification. Stone-free rate after 6 months was also calculated from all subgroups and compared to each other. The rate of successful fragmentation was 76.2% for radiolucent stones and 65.6% for radiopaque stones(p> 0.05) after 46,731 and 56,111 shock wave respectively(p > 0.05) The rate of successful fragmentation was highest in patients with single, radiolucent stone smaller than 2 cm(91.7%) followed by single radiolucent stone larger than 2 cm(83.3%), multiple calcified stones smaller than 2 cm (77.4%) and single calcified stone smaller than 2 cm(72.1%). The rate of complete stone clearance after 6 month follow-up was highest in patients with single radiolucent stone smaller than 2 cm (63.3%) and followed by multiple calcified stones smaller than 2 cm(37.3%), single calcified stone smaller than 2 cm(33.9%)(p < 0.05). To obtain better results with ESWL in patients with gallbladder stone, the authors propose a more strict inclusion criteria, which is the patient with a single, radiolucent stone smaller than 2 cm

Preparation of Plaster Moulage (Cast in Plastic Surgery patients

Directory of Open Access Journals (Sweden)

Rana R

2003-01-01

Full Text Available The purpose of this paper is to describe the technique of making casts using alginate compound for negative and dental stone plaster for positive impressions. With certain modifications a cast could be made of any part of the body and one can make a museum of interesting cases. Casts serve as useful teaching material especially in cleft lip and palate patients to study the effect of surgery on growth and development of the cleft lip-palate-nose complex in relation to the remaining face. It also helps in planning reconstruction in cases of facial defects, recording serial changes in multistage surgery, pre-operative and post-operative comparison as in rhinoplasty, ear reconstruction, hand etc; for comparing results before and after treatment in keloid and hypertrophic scars, fabrication of implants and preparation of prosthesis. In spite of newer modalities like 3-D imaging and stereolithography, the usefulness of this old technique in certain interesting cases can not be denied.

Fire effects on flaked stone, ground stone, and other stone artifacts [Chapter 4

Science.gov (United States)

Krista Deal

2012-01-01

Lithic artifacts can be divided into two broad classes, flaked stone and ground stone, that overlap depending on the defining criteria. For this discussion, flaked stone is used to describe objects that cut, scrape, pierce, saw, hack, etch, drill, or perforate, and the debris (debitage) created when these items are manufactured. Objects made of flaked stone include...

Villamayor stone (Golden Stone) as a Global Heritage Stone Resource from Salamanca (NW of Spain)

Science.gov (United States)

Garcia-Talegon, Jacinta; Iñigo, Adolfo; Vicente-Tavera, Santiago

2013-04-01

Villamayor stone is an arkosic stone of Middle Eocene age and belongs to the Cabrerizos Sandstone Formation that comprising braided fluvial systems and paleosoils at the top of each stratigraphic sequence. The sandstone is known by several names: i) the Villamayor Stone because the quarries are located in Villamayor de Armuña village that are situated at 7 km to the North from Salamanca city; ii) the Golden Stone due to its patina that produced a ochreous/golden color on the façades of monuments of Salamanca (World Heritage City,1988) built in this Natural stone (one of the silicated rocks utilised). We present in this work, the Villamayor Stone to be candidate as Global Heritage Stone Resource. The Villamayor Stone were quarrying for the construction and ornamentation of Romanesque religious monuments as the Old Cathedral and San Julian church; Gothic (Spanish plateresc style) as the New Cathedral, San Esteban church and the sculpted façade of the Salamanca University, one of the oldest University in Europe (it had established in 1250); and this stone was one of the type of one of the most sumptuous Baroque monuments is the Main Square of the its galleries and arcades (1729). Also, this stone was used in building palaces, walls and reconstruction of Roman bridge. Currently, Villamayor Stone is being quarried by small and family companies, without a modernized processing, for cladding of the façades of the new buildings until that the construction sector was burst (in 2008 the international economic crisis). However, Villamayor Stone is the main stone material used in the city of Salamanca for the restoration of monuments and, even in small quantities when compared with just before the economic crisis, it would be of great importance for future generations protect their quarries and the craft of masonry. Villamayor Stone has several varieties from channels facies to floodplains facies, in this work the selected varieties are: i) the fine-grained stone

A study on the industrialization of building stones and industrial stone crafts - Study on the causes of stone contaminations

Energy Technology Data Exchange (ETDEWEB)

Hyun, Jeon Ki; Lee, Han Yeang [Korea Institute of Geology Mining and Materials, Taejon (Korea, Republic of)

1996-12-01

Causes of building stone contamination are acid rains in polluted areas, iron bearing minerals in stone itself, salts, sealants, cutting and grinding processes in stone factory and steel compounds structures such as stone anchors, bolts, rain culvert and guide frames. Contaminations on the building stone surface of Sejong culture center can be found around floor stones, stair stones, parterre stones, pillar stones and other outdoor stone panels. The parterre stones are contaminated by white tarnishes and rust flows are occurred on the surface of pillar stones and outdoor stone panels around entrance. Black tarnishes are cumulated on the pillar stones and other outdoor decorated stone panels and change the original granite color. Causes of building stone contaminations from Sejong culture center are wet method to attach stone panels, rust from steel compounds structures and air pollutants. Cement and mortar used from wet method react with sulfur dioxides in polluted air and from fine calcite crystals (white tarnish). Rusts from steel compounds structures such as rainwater culvert and steel guide frames can move to the stone surface by rain and leave rust flows on it. Pollutants (tar compounds, carbons, dusts, etc.) in air are cumulated with humidity on the stone surface and change color from white granite color to dusty dark color. Historical stone sculptures such as man and animal shaped stone crafts, tombstones, square stone tables in front of a tomb and guide and circumference stones around tomb in Royal Tombs (Donggu rung, Yung rung, Seoou rung and Hunin rung) distributed in Kyunggi province are contaminated by various moss and air pollutants and its original colors are deeply changed. (author). 21 refs., 11 tabs., 22 figs.

Cast erosion from the cleaning of debris after the use of a cast trimmer.

Science.gov (United States)

Hansen, Paul A; Beatty, Mark W

2017-02-01

Whether using tap water to rinse off debris will make a clinical difference to the surface detail of a gypsum cast is unknown. In addition, how best to remove debris from the cast is unknown. The purpose of this in vitro study was to evaluate the efficiency of different methods of cleaning a gypsum cast after trimming and the effect of short-term exposure to tap water on the surface quality of the cast. A die fitting American National Standards Institute/American Dental Association specification 25 (International Standards Organization specification 6873) for dental gypsum products was embedded in a Dentoform with the machined lines positioned at the same level as the occlusal surface of the posterior teeth. A flat plate was used to ensure that the plane of occlusion for the die was at the same position as the posterior teeth. Forty polyvinyl siloxane impressions of the Dentoform were made and poured with vacuum-mixed improved Type IV dental stone. Each cast was inspected for the accurate reproduction of the lines. The base of the 2-stage pour was trimmed with a cast trimmer with water, and surface debris was removed by rinsing by hand under tap water for 10 seconds, by brushing the cast with a soft toothbrush for 10 seconds, or by resoaking the cast and using a soft camel hair brush in slurry water for 10 seconds. The amount of debris was evaluated on a scale of 1 to 4, and the quality of the 20-μm line was evaluated on a scale of 1 to 4 under ×15 magnification. The nonparametric Kruskal-Wallis ranks test was used to identify significant differences among the different cleaning methods (α=.05). Results of the Kruskal-Wallis and Kruskal-Wallis Z-value tests demonstrated that all cleaning methods produced cleaner casts than were observed for uncleansed controls (P<.001), but no differences in debris removal were found among the different cleaning methods (.065≤P≤.901). The ability to see the quality of a 20-μm line (P=.974) was not statistically different

Modeling Stone Columns.

Science.gov (United States)

Castro, Jorge

2017-07-11

This paper reviews the main modeling techniques for stone columns, both ordinary stone columns and geosynthetic-encased stone columns. The paper tries to encompass the more recent advances and recommendations in the topic. Regarding the geometrical model, the main options are the "unit cell", longitudinal gravel trenches in plane strain conditions, cylindrical rings of gravel in axial symmetry conditions, equivalent homogeneous soil with improved properties and three-dimensional models, either a full three-dimensional model or just a three-dimensional row or slice of columns. Some guidelines for obtaining these simplified geometrical models are provided and the particular case of groups of columns under footings is also analyzed. For the latter case, there is a column critical length that is around twice the footing width for non-encased columns in a homogeneous soft soil. In the literature, the column critical length is sometimes given as a function of the column length, which leads to some disparities in its value. Here it is shown that the column critical length mainly depends on the footing dimensions. Some other features related with column modeling are also briefly presented, such as the influence of column installation. Finally, some guidance and recommendations are provided on parameter selection for the study of stone columns.

The utilization of stone ash on cellular lightweight concrete

Science.gov (United States)

Karolina, R.; Sianipar, Y. G. C.

2018-02-01

Lightweight concrete brick is a brick which made of cement, sand, water, and foam as the basic composition. This brick are divided into 2, based on the foam used such as AAC (Autoclave Aerated Concrete) that use aluminium paste and CLC(Cellular Lightweight Concrete) that use foaming agent from BASF as its foaming material. In this trial, the lightweight brick that are ging to be use are the CLC with foaming agent as its foaming material with the mixture of stone ash that are produced by the Stone Crusher with spesific gravity 2666 kg/m3 as their partly sand substitution . In this research, the stone ash variant that are used are 10%, 15%, and 20% from the amount of sand that planned before. After casting, the result of the 10% will receive a reduction of compressive strength while an increasing in absorption as 25.07% and 39.005% and the 15% variant will recieve a reduction of compressive strength as much as 65.8% and a reduction of absorption as much as 17.441% and the 20% variant will recieve a reduction of compressive strength as much as 67.4% while an increasing of absorption as much as 17.956%.

Influence of disinfection with peracetic acid and hypochlorite in dimensional alterations of casts obtained from addition silicone and polyether impressions.

Science.gov (United States)

Queiroz, Daher Antonio; Peçanha, Marcelo Massaroni; Neves, Ana Christina Claro; Frizzera, Fausto; Tonetto, Mateus Rodrigues; Silva-Concílio, Laís Regiane

2013-11-01

Dental impressions disinfection is important to reduce the risk of cross contamination but this process may produce dimensional distortions. Peracetic acid is a disinfectant agent with several favorable characteristics yet underutilized in Dentistry. The aim of this paper is to compare the dimensional stability of casts obtained from addition silicone and polyether impressions that were immersed for 10 minutes in a solution of 0.2% peracetic acid or 1% sodium hypochlorite. Sixty samples in type IV gypsum were produced after a master cast that simulated a full crown preparation of a maxillary premolar. Samples were divided in 6 groups (n = 10) according to the impression material and disinfection agent: Group AC--addition silicone control (without disinfectant); Group APA--addition silicone + 0.2% peracetic acid; Group AH--addition silicone + 1% sodium hypochlorite; Group PC--polyether control (without disinfectant); Group PPA--polyether + 0.2% peracetic acid; Group PH--polyether + 1% sodium hypochlorite. Cast height, base and top diameter were measured and a mean value was obtained for each sample and group all data was statistically analyzed (ANOVA, p polyether impressions regardless of the disinfectant materials. It can be concluded that disinfection with the proposed agents did not produce significant alterations of the impressions and the peracetic acid could be considered a reliable material to disinfect dental molds.

Do Urinary Cystine Parameters Predict Clinical Stone Activity?

Science.gov (United States)

Friedlander, Justin I; Antonelli, Jodi A; Canvasser, Noah E; Morgan, Monica S C; Mollengarden, Daniel; Best, Sara; Pearle, Margaret S

2018-02-01

An accurate urinary predictor of stone recurrence would be clinically advantageous for patients with cystinuria. A proprietary assay (Litholink, Chicago, Illinois) measures cystine capacity as a potentially more reliable estimate of stone forming propensity. The recommended capacity level to prevent stone formation, which is greater than 150 mg/l, has not been directly correlated with clinical stone activity. We investigated the relationship between urinary cystine parameters and clinical stone activity. We prospectively followed 48 patients with cystinuria using 24-hour urine collections and serial imaging, and recorded stone activity. We compared cystine urinary parameters at times of stone activity with those obtained during periods of stone quiescence. We then performed correlation and ROC analysis to evaluate the performance of cystine parameters to predict stone activity. During a median followup of 70.6 months (range 2.2 to 274.6) 85 stone events occurred which could be linked to a recent urine collection. Cystine capacity was significantly greater for quiescent urine than for stone event urine (mean ± SD 48 ± 107 vs -38 ± 163 mg/l, p stone activity (r = -0.29, p r = -0.88, p r = -0.87, p stone quiescence. Decreasing the cutoff to 90 mg/l or greater improved sensitivity to 25.2% while maintaining specificity at 90.9%. Our results suggest that the target for capacity should be lower than previously advised. Copyright © 2018 American Urological Association Education and Research, Inc. Published by Elsevier Inc. All rights reserved.

Which is better? Guy's versus S.T.O.N.E. nephrolithometry scoring systems in predicting stone-free status post-percutaneous nephrolithotomy.

Science.gov (United States)

Noureldin, Yasser A; Elkoushy, Mohamed A; Andonian, Sero

2015-11-01

The aim of the present study was to compare the accuracy of the Guy's and S.T.O.N.E. scoring systems in predicting percutaneous nephrolithotomy (PCNL) outcomes. After obtaining ethics approval, medical records of patients undergoing PCNL between 2009 and 2013 at a tertiary stone center were retrospectively reviewed. Guy's and S.T.O.N.E. scoring systems were calculated. Regression analysis and ROC curves were performed. A total of 185 PCNLs were reviewed. The overall stone-free rate was 71.9 % with a complication rate of 16.2 %. When compared to patients with residual fragments, stone-free patients had significantly lower Guy's grade (2.7 vs. 2; p stone-free status, OR 0.4 (p r = 0.3, p r = 0.4, p r = 0.2, p = 0.001 and r = 0.3, p stone-free status. Other factors not included in either scoring system may need to be incorporated in the future to increase their accuracy.

Ureteroscopy and stone lithotripsy with lithoclast: personal experience.

Science.gov (United States)

Leidi, G L; Berti, G L; Canclini, L; Giola, V; Maccaroni, A; Raimoldi, A; Veneroni, L; Bacchioni, A M

1997-06-01

Ureteroscopy has become a common technique in the diagnosis and treatment of ureteral pathologies, but this procedure is quite invasive and some complications have been reported in literature. In our Institute 49 patients underwent ureteroscopy and ballistic lithotripsy with lithoclast for ureteral stones. The stones were localized both in the middle and distal part of the ureter. We used a small caliber 7-8.5 Wolf ureteroscope. The treatments were performed under antibiotic prophylaxis. Direct access to the ureter without dilation of the meatus was obtained in 97.96% of patients. The stones were easily reached in 93.88% of the cases and satisfactory fragmentation was obtained in 90.7%. In 4 patients (9.3%) one or more large stone fragments escaped into the kidney, requiring the patients to be treated with ESWL. No major complications occurred: no ureteral perforations, no important bleeding and no severe or persistent infections. All patients were discharged in one to four days postoperatively. The authors conclude that ureteroscopy using small caliber instruments with Lithoclast is a safe and satisfactory alternative to ESWL in the treatment of ureteral stones.

Self-disinfecting Alginate vs Conventional Alginate: Effect on Surface Hardness of Gypsum Cast-An in vitro Study.

Science.gov (United States)

Madhavan, Ranjith; George, Navia; Thummala, Niharika R; Ravi, S V; Nagpal, Ajay

2017-11-01

For the construction of any dental prosthesis, accurate impressions are necessary. Hence, we undertook the present study to evaluate and compare the surface hardness of gypsum casts poured from impressions made using conventional alginate and self-disinfecting alginate. A total of 30 impressions of stainless steel die were made, out of which 15 impressions were made with conventional alginate and 15 were made with self-disinfecting alginate and poured using Type III dental stone. Thirty stone specimens were subjected for hardness testing. Data were analyzed using independent samples t-test to compare the mean surface hardness. Difference in surface hardness was statistically insignificant (p > 0.05). Surface hardness of gypsum casts poured using impressions made from self-disinfecting alginate and conventional alginates were comparable. Self-disinfecting alginates may be employed in clinical practice as safe and effective materials to overcome the infection control issues without compromising on the properties of the material.

Effects of microgravity on renal stone risk assessment

Science.gov (United States)

Pietrzyk, R. A.; Pak, C. Y. C.; Cintron, N. M.; Whitson, P. A.

1992-01-01

Physiologic changes induced during human exposure to the microgravity environment of space may contribute to an increased potential for renal stone formation. Renal stone risk factors obtained 10 days before flight and immediately after return to earth indicated that calcium oxalate and uric acid stone-forming potential was increased after space flights of 4-10 days. These data describe the need for examining renal stone risk during in-flight phases of space missions. Because of limited availability of space and refrigerated storage on spacecraft, effective methods must be developed for collecting urine samples in-flight and for preserving (or storing) them at temperatures and under conditions commensurate with mission constraints.

Assessment of stone composition in the management of urinary stones

NARCIS (Netherlands)

Kijvikai, Kittinut; de la Rosette, J. J. M.

2011-01-01

Several explanations have been suggested to account for the failure of extracorporeal shockwave lithotripsy (ESWL) treatment in patients with urinary stones, including large stone volume, unfavorable stone location or composition and the type of lithotriptor used. Unfavorable stone composition is

Infection (urease) stones.

Science.gov (United States)

Griffith, D P; Osborne, C A

1987-01-01

Infection-induced stones in man probably form solely as a consequence of urealysis which is catalyzed by the bacterial protein urease. Urease stones composed of struvite and carbonate-apatite may form primarily, or as secondary stones or pre-existent metabolic stones. Struvite stones form and grow rapidly owing to (a) supersaturation of urine with stone forming salts, (b) 'salting out' of poorly soluble organic substances normally dissolved in urine and (c) ammonia-induced destruction of the normally protective urothelial glycosaminoglycan layer. Immature (predominantly organic) matrix stones mature into densely mineralized stones. Curative treatment is possible only by eliminating all of the stone and by eradicating all urinary and parenchymal infection. A variety of operative and pharmaceutical approaches are available. Patient treatment must be individualized inasmuch as some patients are better candidates for one type of treatment than another.

Marginal Accuracy of Castings Fabricated with Ringless Casting Investment System and Metal Ring Casting Investment System: A Comparative Study.

Science.gov (United States)

Kalavathi, M; Sachin, Bhuvana; Prasanna, B G; Shreeharsha, T V; Praveen, B; Ragher, Mallikarjuna

2016-02-01

The thermal expansion of the investment can be restricted by the metal casting ring because the thermal expansion of the ring is less than that of the investment. The ringless casting procedure is in use in clinical dentistry, though there is little scientific data to support its use in fixed partial dentures. In this study, marginal discrepancy of castings produced with the ringless casting technique and the conventional technique using the metal rings were compared. A total of 30 wax patterns were fabricated directly on a metal die. Optical stereomicroscope was used to measure the marginal discrepancy between the metal die and wax patterns. A total of 15 castings were invested using Bellavest T phosphate-bonded investment with the ringless technique and 15 were invested with the same investment with a metal ring; 30 castings were produced using a nickel-chromium ceramo-metal alloy. The internal surface of the castings was not modified and seated with finger pressure. The vertical marginal discrepancy was measured using an optical stereomicroscope at a magnification of 100x. The data obtained were statistically analyzed using students t-test (paired t-test and unpaired t-test). The castings of the ringless technique provided less vertical marginal discrepancy (240.56 ± 45.81 μ) than the castings produced with the conventional metal ring technique (281.98± 53.05 μ). The difference was statistically significant. The ringless casting technique had produced better marginal accuracy compared with conventional casting technique. Ringless casting system can be used routinely for clinical purpose.

Shielding features of quarry stone

International Nuclear Information System (INIS)

Hernandez V, C.; Contreras S, H.; Hernandez A, L.; Baltazar R, A.; Escareno J, E.; Mares E, C. A.; Vega C, H. R.

2010-10-01

Quarry stone lineal attenuation coefficient for gamma-rays has been obtained. In Zacatecas, quarry stone is widely utilized as a decorative item in buildings, however its shielding features against gamma-rays unknown. The aim of this work is to determine the shielding properties of quarry stone against γ-rays using Monte Carlo calculations where a detailed model of a good geometry experimental setup was carried out. In the calculations 10 pieces 10 X 10 cm 2 of different thickness were utilized to evaluate the photons transmission as the quarry stone thickness is increased. It was noticed that transmitted photons decay away as the shield thickness is increased, these results were fitted to an exponential function were the linear attenuation coefficient was estimated. Also, using XCOM code the linear attenuation coefficient from several keV up to 100 MeV was estimated. From the comparison between Monte Carlo results and XCOM calculations a good agreement was found. For 0.662 MeV γ-rays the attenuation coefficient of quarry stone, whose density is 2.413 g-cm -3 , is 0.1798 cm -1 , this mean a X 1/2 = 3.9 cm, X 1/4 = 7.7 cm, X 1/10 = 12.8 cm, and X 1/100 = 25.6 cm. Having the information of quarry stone performance as shielding give the chance to use this material to shield X and γ-ray facilities. (Author)

Study of the rheological properties of casting slips obtained from titanium oxide and bariun titanate in order to obtain pieces by means of casting in plaster moulds

International Nuclear Information System (INIS)

Amarante Junior, A.

1986-01-01

The behaviour of titanium-oxide (TiO 2 ) and barium titanate used in slip casting with plaster moulds is studied. Some data in several tests, as well as materials and methods applied are presented. (M.J.C.) [pt

Cast Iron in The 19th Century Building Equipment

Science.gov (United States)

Kwasek, Michał; Piwek, Aleksander

2017-10-01

Cast iron is a material, characteristics of which enable to receive extremely artistic elements. It maintains good strength properties at the same time. That combination of these seemingly contrary traits makes it a commodity that was widely used in the 19th century industry and architecture. These usages were not only as decorative elements, technical and structural ones. The production of new household utilities started, which made people’s lives more comfortable. Cast iron allowed for fast and cheap production while maintaining high aesthetic qualities. Useful elements, which often were ornamental parts of buildings were created. The aim of the article is to characterise elements of interior equipment of the 19th century building that are made of cast iron. As it appears from performed bibliography, archival and field studies, the ways of exploitation are very broad. Some were mounted into the building; the others were a mobile equipment. As it occurred they were most commonly used as functional items. Cast iron was used to produce the minor elements, which were only parts of the bigger wooden or stone items. Notwithstanding, there were also bigger ones casted as a whole, and frequently ones that were assembled from many elements. Nowadays, elements of an interior feature are one of the subjects of study during the restoration work of the buildings. They can provide important information about the building and the way people lived and are considered as the essential part of historical objects.

Evaluation of stone volume distribution in renal collecting system as a predictor of stone-free rate after percutaneous nephrolithotomy: a retrospective single-center study.

Science.gov (United States)

Atalay, Hasan Anıl; Canat, Lutfi; Bayraktarlı, Recep; Alkan, Ilter; Can, Osman; Altunrende, Fatih

2017-06-23

We analyzed our stone-free rates of PNL with regard to stone burden and its ratio to the renal collecting system volume. Data of 164 patients who underwent PNL were analyzed retrospectively. Volume segmentation of renal collecting system and stones were done using 3D segmentation software with the images obtained from CT data. Analyzed stone volume (ASV) and renal collecting system volume (RCSV) were measured and the ASV-to-RCSV ratio was calculated after the creation of a 3D surface volume rendering of renal stones and the collecting system. Univariate and multivariate statistical analyses were performed to determine factors affecting stone-free rates; also we assessed the predictive accuracy of the ASV-to-RCSV ratio using the receiving operating curve (ROC) and AUC. The stone-free rate of PNL monotherapy was 53% (164 procedures).The ASV-to-RCSV ratio and calyx number with stones were the most influential predictors of stone-free status (OR 4.15, 95% CI 2.24-7.24, renal collecting system, which is calculated using the 3D volume segmentation method, is a significant determinant of the stone-free rate before PCNL surgery. It could be used as a single guide variable by the clinician before renal stone surgery to predict extra requirements for stone clearance.

Can Hounsfield Unit Value Predict Type of Urinary Stones?

Directory of Open Access Journals (Sweden)

Alper Gok

2014-03-01

Full Text Available Aim: Aim of this study is to determine the role of Hounsfield unit (HU in predicting results of stone analysis. Material and Method: This study included 199 patients to whom percutaneous nephrolithotomy (PNL procedures were applied between January 2008 and May 2011 in our clinic. Before the procedure HU values of kidney stones were measured using non-contrast computed tomography. After the operation, obtained stone samples were analysed using X-ray diffraction technique. HU values were compared with stone analysis results. Results: Stone analysis revealed eight different stone types. Distribution of stone types and HU value ranges were as follows: 85% calcium oxalate monohydrate, 730-1130 HU; 38% calcium oxalate dihydrate, 510-810 HU; 21% uric acid, 320-550 HU; 23% struvite, 614-870 HU; 7% calcium hydrogene phosphate, 1100-1365 HU; 3% cystine, 630-674 HU; 15% mixed uric acid plus calcium oxalate, 499-840 HU; and 7% mixed cystine plus calcium phosphate, 430-520 HU. HU values of all stone types ranged between 320 and 1365. There was a statistically significant relation between HU values of uric acid and non uric acid stones (p

Centrifugal Casting Features/Metallurgical Characterization of Aluminum Alloys

International Nuclear Information System (INIS)

Chirita, G.; Soares, D.; Cruz, D.; Silva, F. S.; Stefanescu, I.

2008-01-01

This paper deals with the study of centrifugal effects on aluminium castings under high G values. Most of the studies in this domain (FGMs obtained by centrifugal casting) deal with functionally graded composites reinforced with a solid phase such as silicon particles or others. However, in this study it will be shown that unreinforced aluminium alloys may be significantly influenced by the centrifugal effect and that functionally graded castings are also obtained. It has been observed that the centrifugal effect may increase in some alloys, depending on the relative position in the castings, the rupture strength by approx. 50%, and rupture strain by about 300%, as compared to the gravity casting technique. The Young's modulus may also increase by about 20%. It has also been reported that in vertical centrifugal castings there are mainly three aspects that affect the components thus obtained, namely: fluid dynamics; vibration (inherent to the system); and centrifugal force. These features have a different effect on the castings depending on the aluminium alloy. In this paper, an analysis of the most important effects of the centrifugal casting process on metallurgical features is conducted. A solidification characterization at several points along the mould will be made in order to have an accurate idea of both the fluid dynamics inside the mould during the casting and the solidification behavior in different parts of the component. These two analyses will be related to the metallurgical properties (phase distribution; SDAS; eutectic silicon content and shape, pores density and shape) along the component and mainly along the direction of the centrifugal pressure. A comparison between castings obtained by both centrifugal casting technique and gravity casting technique is made for reference (gravity casting)

Pollution effects on stone benches of the Eagle Warriors Precinct at the Major Temple, Mexico City

International Nuclear Information System (INIS)

Miranda, J.; Gallardo, M.L.; Grimaldi, D.M.; Roman-Berrelleza, J.A.; Ruvalcaba-Sil, J.L.; Ontalba Salamanca, M.A.; Morales, J.G.

1999-01-01

During Major Temple archaeological site excavations in Downtown Mexico City, the precinct of one of the most important Mexica military caste, the Eagle Warriors, was discovered. The ceremonial enclosure is composed of three rooms surrounded by paintings on 11 stone benches placed against the walls. Nowadays, these paintings and the stones present the effects of different deterioration processes produced by the underground water level, high humidity, and the presence of soil, water, and air pollutants. Ion beam analysis of samples from the benches and wall paintings was performed using PIXE and RBS techniques. Using enrichment factors of elements relative to iron concentrations, possible contamination by sulfur and chlorine salts was found, as well as airborne zinc scavenged by rain

Anodization of cast aluminium alloys produced by different casting methods

Directory of Open Access Journals (Sweden)

K. Labisz

2008-08-01

Full Text Available In this paper the usability of two casting methods, of sand and high pressure cast for the anodization of AlSi12 and AlSi9Cu3 aluminium cast alloys was investigated. With defined anodization parameters like electrolyte composition and temperature, current type and value a anodic alumina surface layer was produced. The quality, size and properties of the anodic layer was investigated after the anodization of the chosen aluminium cast alloys. The Alumina layer was observed used light microscope, also the mechanical properties were measured as well the abrasive wear test was made with using ABR-8251 equipment. The researches included analyze of the influence of chemical composition, geometry and roughness of anodic layer obtained on aluminum casts. Conducted investigations shows the areas of later researches, especially in the direction of the possible, next optimization anodization process of aluminum casting alloys, for example in the range of raising resistance on corrosion to achieve a suitable anodic surface layer on elements for increasing applications in the aggressive environment for example as materials on working building constructions, elements in electronics and construction parts in air and automotive industry.

Do stone size and impaction influence therapeutic approach to proximal ureteral stones?

Directory of Open Access Journals (Sweden)

Radulović Slobodan

2009-01-01

Full Text Available Background/Aim. Primary therapeutic approach to lumbar ureteral stones is still contraversial. The aim of the study was to investigate the influence of stone impaction and size on the effectiveness of proximal ureteral stone lithotripsy. Methods. A total of 123 patients with proximal ureteral stones were investigated in this prospective study performed in a 10- month period. The patients were divided into the group I - 86 patients treated with extracorporeal shock wave lithotripsy (ESWL and the group II - 37 patients treated with 'Swiss' Lithoclast. In the group I, 49 stones (57% were classified as impacted, while 20 stones (23.3% were larger than 100 mm2. In the group II, 26 stones (70.3% were impacted, and 11 stones (29.7% were larger than 100 mm2. Stones were defined as impacted by the radiographic, echosonographic as well as endoscopic findings in the group II of patients. Stone size was presented in mm2. Chemical composition of stones were almost the same in both groups of the patients. Results. Generally, there was no statistically significant difference in the treatment success between the groups. However, stones larger than 100 mm2 were statistically more successfully treated endoscopically, while there was no statistical difference in the treatment success of impacted stones between these two groups. Conclusion. ESWL can by considered as primary first therapeutic approach in treatment of all proximal ureteral stones except for stones larger than 100 mm2 that should primarily be treated endoscopically.

Usefulness of 99mTc-DTPA renography and diuretic renography in predicting successful stone discharge following outpatient ESWL in patients with a single ureteral stone

International Nuclear Information System (INIS)

Soga, Norihito; Komeda, Yoshinori; Suzuki, Ryuichi; Kawamura, Juichi.

1996-01-01

We analyzed the 99m Tc-DTPA renogram with and without diuresis to predict the possibility of stone discharge on the outpatient basis by renogram patterns. Between October 1993 and December 1995, 99m Tc-DTPA renography was performed in 79 patients with a single ureteral stone. The 99m Tc-DTPA renogram pattern was classified into the three types of normal function, obstruction and lower function patterns and the complete stone discharge rate was 93, 63 and 25%, respectively. In addition, diuretic renography using Furosemide was performed in patients with an obstruction pattern and the three renogram patterns of return to the normal curve, a diuretic response and no response were obtained; the complete stone discharge rate was 44, 65.3 and 93%, respectively. From this study, patients with a single ureteral stone with a normal pattern on the regular DTPA renogram and patients with no response pattern on the diuretic renogram, even if in such patients an obstructive pattern was seen on the regular DTPA renogram, seem to be a good candidate for obtaining a high rate of a stone discharge with extracorporeal shock wave lithotripsy (ESWL) treatment in the outpatients basis. (author)

[The surface roughness analysis of the titanium casting founding by a new titanium casting investment material].

Science.gov (United States)

Liang, Qin-ye; Wu, Xia-yi; Lin, Xue-feng

2012-04-01

To investigate the surface roughness property of the titanium castings cast in a new investment for titanium casting. Six wax patterns (20 mm × 20 mm × 0.5 mm) were invested using two investments: three in a new titanium investment material and three in the control material (Rematitan Plus). Six titanium specimens were obtained by conventional casting. After casting, surface roughness of the specimens were evaluated with a surface profilometer. The surface roughness of the specimens cast in new titanium investment material was (1.72 ± 0.08) µm, which was much smaller than that from Rematitan Plus [(1.91 ± 0.15) µm, P cast using these two investment materials are both smooth enough to fulfill the demand of the titanium precision-casting for prosthodontic clinical use.

Open stone surgery: a still-in-use approach for complex stone burden.

Science.gov (United States)

Çakici, Özer Ural; Ener, Kemal; Keske, Murat; Altinova, Serkan; Canda, Abdullah Erdem; Aldemir, Mustafa; Ardicoglu, Arslan

2017-06-30

Urinary stone disease is a major urological condition. Endourologic techniques have influenced the clinical approach and outcomes. Open surgery holds a historic importance in the management of most conditions. However, complex kidney stone burden may be amenable to successful results with open stone surgery. In this article, we report our eighteen cases of complex urinary stone disease who underwent open stone removal. A total of 1701 patients have undergone surgical treatment for urinary stone disease in our clinic between July 2012 and July 2016, comprising eighteen patients who underwent open stone surgery. Patients' demographic data, stone analysis results, postoperative clinical data, and stone status were evaluated retrospectively. The choice of surgical approach is mostly dependent on the surgeon's preference. In two patients, open surgery was undertaken because of perioperative complications. We did not observe any Clavien-Dindo grade 4 or 5 complications. Three patients were managed with a course of antibiotics due to postoperative fever. One patient had postoperative pleurisy, one patient had urinoma, and two patients had postoperative ileus. Mean operation time was 84 (57-124) minutes and mean hospitalization time was 5.5 (3-8) days. Stone-free status was achieved in 15 patients (83.3%). Endourologic approaches are the first options for treatment of urinary stone disease. However, open stone surgery holds its indispensable position in complicated cases and in complex stone burden. Open stone surgery is also a valid alternative to endourologic techniques in all situations.

Mechanical properties of as-cast microalloyed steels produced via investment casting

International Nuclear Information System (INIS)

Najafi, H.; Rassizadehghani, J.; Norouzi, S.

2011-01-01

Tensile and room temperature Charpy V-notch impact tests were used to evaluate the variations in the as-cast mechanical properties of a low-carbon steel produced via shell mould investment casting and containing combinations of vanadium, niobium and titanium. Tensile results indicate that the yield strength and ultimate tensile strength (UTS) have increased up to respectively 615 MPa and 770 MPa due to the fine-scale microalloy precipitates in the microalloyed samples. Room temperature impact test results show that while addition of vanadium individually has not changed the impact energy, Nb has decreased it considerably. However, examination of fracture surfaces reveals that all microalloyed samples have failed by transgranular cleavage. Based on the transmission electron microscope (TEM) studies, it seems that carbonitrides being greater than 50 nm in size and formed along prior austenite grain boundaries before γ transformation are responsible for the observed reduction in impact energies and brittle fracture. In comparison to sand mould casting, the yield and UTS obtained from investment casting are superior. Furthermore, although the impact energies of Nb-containing alloys are approximately the same as those obtained from sand moulds, the impact energy of the alloy containing only vanadium has improved considerably.

Contribution of stone size to chronic kidney disease in kidney stone formers.

Science.gov (United States)

Ahmadi, Farrokhlagha; Etemadi, Samira Motedayen; Lessan-Pezeshki, Mahbob; Mahdavi-Mazdeh, Mitra; Ayati, Mohsen; Mir, Alireza; Yazdi, Hadi Rokni

2015-01-01

To determine whether stone burden correlates with the degree of chronic kidney disease in kidney stone formers. A total of 97 extracorporeal shockwave lithotripsy candidates aged 18 years and older were included. Size, number and location of the kidney stones, along with cumulative stone size, defined as the sum of diameters of all stones) were determined. Estimated glomerular filtration rate was determined using the Chronic Kidney Disease Epidemiology Collaboration cystatin C/creatinine equation, and chronic kidney disease was defined as estimated glomerular filtration rate chronic kidney disease. The relationship persisted even after adjustment for age, sex, body mass index, C-reactive protein, fasting plasma glucose, thyroid stimulating hormone, presence of microalbuminuria, history of renal calculi, history of extracorporeal shockwave lithotripsy, number and location of the stones (odds ratio 1.24, 95% confidence interval 1.02-1.52). The same was not observed for individuals with a cumulative stone size ≥ 20 mm. In kidney stone formers with a cumulative stone size up to 20 mm, estimated glomerular filtration rate linearly declines with increasing cumulative stone size. Additionally, cumulative stone size is an independent predictor of chronic kidney disease in this group of patients. © 2014 The Japanese Urological Association.

Urinary stone composition in Oman: with high incidence of cystinuria.

Science.gov (United States)

Al-Marhoon, Mohammed S; Bayoumi, Riad; Al-Farsi, Yahya; Al-Hinai, Abdullhakeem; Al-Maskary, Sultan; Venkiteswaran, Krishna; Al-Busaidi, Qassim; Mathew, Josephkunju; Rhman, Khalid; Sharif, Omar; Aquil, Shahid; Al-Hashmi, Intisar

2015-06-01

Urinary stones are a common problem in Oman and their composition is unknown. The aim of this study is to analyze the components of urinary stones of Omani patients and use the obtained data for future studies of etiology, treatment, and prevention. Urinary stones of 255 consecutive patients were collected at the Sultan Qaboos University Hospital. Stones were analyzed by Fourier transform infrared spectrophotometer. The biochemical, metabolic, and radiological data relating to the patients and stones were collected. The mean age was 41 years, with M:F ratio of 3.7:1. The common comorbidities associated with stone formation were hypertension; diabetes, benign prostate hyperplasia; urinary tract infection; obesity; and atrophic kidney. The common presentation was renal colic and flank pain (96%). Stones were surgically retrieved in 70% of patients. Mean stone size was 9 ± 0.5 mm (range 1.3-80). Stone formers had a BMI ≥ 25 in 56% (P = 0.006) and positive family history of stones in 3.8%. The most common stones in Oman were as follows: Calcium Oxalates 45% (114/255); Mixed calcium phosphates & calcium oxalates 22% (55/255); Uric Acid 16% (40/255); and Cystine 4% (10/255). The most common urinary stones in Oman are Calcium Oxalates. Overweight is an important risk factor associated with stone formation. The hereditary Cystine stones are three times more common in Oman than what is reported in the literature that needs further genetic studies.

Bath Stone - a Possible Global Heritage Stone from England

Science.gov (United States)

Marker, Brian

2014-05-01

The Middle Jurassic strata of England have several horizons of oolitic and bioclastic limestones that provide high quality dimension stone. One of the most important is found in and near the City of Bath. The Great Oolite Group (Upper Bathonian) contains the Combe Down and Bath Oolites, consisting of current bedded oolites and shelly oolites, that have been used extensively as freestones for construction nearby, for prestigious buildings through much of southern England and more widely. The stone has been used to some extent since Roman times when the city, then known as Aquae Sulis, was an important hot spa. The stone was used to a limited extent through medieval times but from the early 18th century onwards was exploited on a large scale through surface quarrying and underground mining. The City was extensively redeveloped in the 18th to early 19th century, mostly using Bath Stone, when the spas made it a fashionable resort. Buildings from that period include architectural "gems" such as the Royal Crescent and Pulteney Bridge, as well as the renovated Roman Baths. Many buildings were designed by some of the foremost British architects of the time. The consistent use of this stone gives the City an architectural integrity throughout. These features led to the designation of the City as a World Heritage Site. It is a requirement in current City planning policy documents that Bath Stone should be used for new building to preserve the appearance of the City. More widely the stone was used in major houses (e.g. Buckingham Palace and Apsley House in London; King's Pavilion in Brighton); civic buildings (e.g. Bristol Guildhall; Dartmouth Naval College in Devon); churches and cathedrals (e.g. Truro Cathedral in Cornwall); and engineered structures (e.g. the large Dundas Aqueduct on the Kennet and Avon Canal). More widely, Bath Stone has been used in Union Station in Washington DC; Toronto Bible College and the Town Hall at Cape Town, South Africa. Extraction declined in

Microsegregation in Nodular Cast Iron with Carbides

Directory of Open Access Journals (Sweden)

S. Pietrowski

2012-12-01

Full Text Available In this paper results of microsegregation in the newly developed nodular cast iron with carbides are presented. To investigate the pearlitic and bainitic cast iron with carbides obtained by Inmold method were chosen. The distribution of linear elements on the eutectic cell radius was examined. To investigate the microsegregation pearlitic and bainitic cast iron with carbides obtained by Inmold method were chosen.The linear distribution of elements on the eutectic cell radius was examined. Testing of the chemical composition of cast iron metal matrix components, including carbides were carried out. The change of graphitizing and anti-graphitizing element concentrations within eutectic cell was determined. It was found, that in cast iron containing Mo carbides crystallizing after austenite + graphite eutectic are Si enriched.

Microsegregation in Nodular Cast Iron with Carbides

Directory of Open Access Journals (Sweden)

Pietrowski S.

2012-12-01

Full Text Available In this paper results of microsegregation in the newly developed nodular cast iron with carbides are presented. To investigate the pearlitic and bainitic cast iron with carbides obtained by Inmold method were chosen. The distribution of linear elements on the eutectic cell radius was examined. To investigate the microsegregation pearlitic and bainitic cast iron with carbides obtained by Inmold method were chosen. The linear distribution of elements on the eutectic cell radius was examined. Testing of the chemical composition of cast iron metal matrix components, including carbides were carried out. The change of graphitizing and anti-graphitizing element concentrations within eutectic cell was determined. It was found, that in cast iron containing Mo carbides crystallizing after austenite + graphite eutectic are Si enriched.

Diffusion of C and Cr During Creation of Surface Layer on Cast Steel Casting

Directory of Open Access Journals (Sweden)

Szajnar J.

2014-10-01

Full Text Available In paper a method of improvement in utility properties of unalloyed cast steel casting in result of diffusion of C and Cr in process of creation of surface layer is presented. The aim of paper was determination of diffusion range of basic elements of alloyed surface layer. Moreover a quantitative analysis of carbides phase strengthens alloyed surface layer of casting was carried out. The results of studies shown that important factors of surface layer creation are maximal temperature Tmax on granular insert – cast steel boundary dependent of pouring temperature, granularity Zw of Fe-Cr-C alloy insert and thickness of casting wall gśo. On the basis of obtained results was affirmed that with increase of thickness of casting wall increases range of diffusion in solid state in Fe-Cr-C grains and in liquid state. Moreover the range of Tmax = 13001500oC favours creation of the proper alloyed surface layers on cast steel.

Usefulness of {sup 99m}Tc-DTPA renography and diuretic renography in predicting successful stone discharge following outpatient ESWL in patients with a single ureteral stone

Energy Technology Data Exchange (ETDEWEB)

Soga, Norihito; Komeda, Yoshinori [Yokkaichi Health Insurance Hospital, Mie (Japan); Suzuki, Ryuichi; Kawamura, Juichi

1996-11-01

We analyzed the {sup 99m}Tc-DTPA renogram with and without diuresis to predict the possibility of stone discharge on the outpatient basis by renogram patterns. Between October 1993 and December 1995, {sup 99m}Tc-DTPA renography was performed in 79 patients with a single ureteral stone. The {sup 99m}Tc-DTPA renogram pattern was classified into the three types of normal function, obstruction and lower function patterns and the complete stone discharge rate was 93, 63 and 25%, respectively. In addition, diuretic renography using Furosemide was performed in patients with an obstruction pattern and the three renogram patterns of return to the normal curve, a diuretic response and no response were obtained; the complete stone discharge rate was 44, 65.3 and 93%, respectively. From this study, patients with a single ureteral stone with a normal pattern on the regular DTPA renogram and patients with no response pattern on the diuretic renogram, even if in such patients an obstructive pattern was seen on the regular DTPA renogram, seem to be a good candidate for obtaining a high rate of a stone discharge with extracorporeal shock wave lithotripsy (ESWL) treatment in the outpatients basis. (author)

Multiscale modeling for the prediction of casting defects in investment cast aluminum alloys

International Nuclear Information System (INIS)

Hamilton, R.W.; See, D.; Butler, S.; Lee, P.D.

2003-01-01

Macroscopic modeling of heat transfer and fluid flow is now routinely used for the prediction of macroscopic defects in castings, while microscopic models are used to investigate the effects of alloy changes on typical microstructures. By combining these two levels of modeling it is possible to simulate the casting process over a wider range of spatial and temporal scales. This paper presents a multiscale model where micromodels for dendrite arm spacing and microporosity are incorporated into a macromodel of heat transfer and in order to predict the as cast microstructure and prevalence of microscopic defects, specifically porosity. The approach is applied to aluminum alloy (L169) investment castings. The models are compared with results obtained by optical image analysis of prepared slices, and X-ray tomography of volume samples from the experiments. Multiscale modeling is shown to provide the designer with a useful tool to improve the properties of the final casting by testing how altering the casting process affects the final microstructure including porosity

Accuracy of ringless casting and accelerated wax-elimination technique: a comparative in vitro study.

Science.gov (United States)

Prasad, Rahul; Al-Keraif, Abdulaziz Abdullah; Kathuria, Nidhi; Gandhi, P V; Bhide, S V

2014-02-01

The purpose of this study was to determine whether the ringless casting and accelerated wax-elimination techniques can be combined to offer a cost-effective, clinically acceptable, and time-saving alternative for fabricating single unit castings in fixed prosthodontics. Sixty standardized wax copings were fabricated on a type IV stone replica of a stainless steel die. The wax patterns were divided into four groups. The first group was cast using the ringless investment technique and conventional wax-elimination method; the second group was cast using the ringless investment technique and accelerated wax-elimination method; the third group was cast using the conventional metal ring investment technique and conventional wax-elimination method; the fourth group was cast using the metal ring investment technique and accelerated wax-elimination method. The vertical marginal gap was measured at four sites per specimen, using a digital optical microscope at 100× magnification. The results were analyzed using two-way ANOVA to determine statistical significance. The vertical marginal gaps of castings fabricated using the ringless technique (76.98 ± 7.59 μm) were significantly less (p castings fabricated using the conventional metal ring technique (138.44 ± 28.59 μm); however, the vertical marginal gaps of the conventional (102.63 ± 36.12 μm) and accelerated wax-elimination (112.79 ± 38.34 μm) castings were not statistically significant (p > 0.05). The ringless investment technique can produce castings with higher accuracy and can be favorably combined with the accelerated wax-elimination method as a vital alternative to the time-consuming conventional technique of casting restorations in fixed prosthodontics. © 2013 by the American College of Prosthodontists.

Simulation of the injection casting of metallic fuels

International Nuclear Information System (INIS)

Nakagawa, Tomokazu; Ogata, Takanari; Tokiwai, Moriyasu.

1989-01-01

For the fabrication of metallic fuel pins, injection casting is a preferable process because the simplicity of the process is suitable for remote operation. In this process, the molten metal in the crucible is injected into evacuated molds (suspended above the crucible) by pressurizing the casting furnace. Argonne National Laboratory has already adopted this process in the Integral Fast Reactor program. To obtain fuel pins with good quality, the casting parameters, such as the molten metal temperature, the magnitude of the pressure applied, the pressurizing rate, the cooling time, etc., must be optimized. Otherwise, bad-quality castings (short castings, rough surfaces, shrinkage cavities, mold fracture) may result. Therefore, it is very important in designing the casting equipment and optimizing the operation conditions to be able to predict the fluid and thermal behavior of the castings. This paper describes methods to simulate the heat and mass transfer in the molds and molten metallic fuel during injection casting. The results obtained by simulation are compared with experimental ones. Also, appropriate casting conditions for the uranium-plutonium-zirconium alloy are discussed based on the simulated results

Pattern of urinary tract stone diseases in Mekelle, Ethiopia.

Science.gov (United States)

Alemu, Mekonnen Hagos

2008-07-01

To evaluate and analyze the pattern of patients with urinary stone diseases admitted to Mekelle Hospital. Between Sept 2003 to Sept 2006, 102 patients with urinary stone disease were admitted to Mekelle Hospital. In this descriptive retrospective audit, case notes were obtained from medical record office and were analyzed for age, sex, localization of the stone disease and the geographic back grounds. Seventy six (74.5%) of the patients were males and 26 (25.5%) were females. There were 102 (13.6%) cases of urinary stone disease admitted to Mekelle Hospital out of 750 total admissions for urological disease for intervention in the surgical ward during the study period. There were 76 (74.5%) males and 26 (25.5%) females and the sex ratio was (M: F: 2.9:1). Most (46.0%) of the urinary stone diseases were between 0-19 year age group both in males and females. The median age was 20 years (range from 2-74 years) and the mean was 25.4 years. Urinary bladder stones were the most common urinary tract stone diseases accounting for 47 (46.0%) followed by renal stones 29 (28.4%), ureteric 16 (15.6%) and urethral 10 (9.8%) stone disease; in that order of frequency. The geographical back ground of the patients with urinary tract stone disease in this report has shown that majorities (53.7%) were from urban and the remaining (44.2%) were from the rural areas. This study has depicted that urinary bladder stone diseases are the most common stone diseases affecting the younger age group. Since this is an institutional based study, it underestimates the magnitude and the pattern of urinary stone diseases at all level. Nevertheless, the audit provides useful information on the socio demographic variables, localization and the geographic back ground of the patients.

Influence of microscopic casting defects on fatigue endurance of ductile cast iron

Directory of Open Access Journals (Sweden)

Nový František

2018-01-01

Full Text Available In this work, there are published results about fatigue endurance of ductile cast iron obtained at high-frequency sinusoidal cyclic push-pull loading in the ultra-high cycle fatigue region. The main attention was focused on the fatigue lifetime data scatter caused by the influence of microscopic casting defects (microshrinkages, microbubbles, microcracks, non-metallic inclusions and local clusters of big graphitic nodules.

The effect of thermohydrogen treatment on the structure and properties of casts obtained from titanium alloys

International Nuclear Information System (INIS)

Il'in, A.A.; Skvortsova, S.V.; Mamonov, A.M.; Permyakova, G.V.; Kurnikov, D.A.

2002-01-01

The method based on the combination of high temperature gas-static and thermal hydrogen treatments is suggested to increase mechanical properties of cast pseudo-α and (α+β)-titanium alloys. The study is carried out using alloys VT20L, VT23L and alloy Ti-6%Al-2%Mo-4%Zr-2%Sn. It is shown that the method proposed provides the change in a cast structure, an increase in density of castings, an increase of strength properties by 10-20% and fatigue by a factor of 1.5-2 at satisfactory ductility and impact strength [ru

Purbeck Stone - A possible Global Heritage Stone from England

Science.gov (United States)

Marker, Brian

2014-05-01

By definition, a Global Heritage Stone Resource (GHSR) should have international significance. The Purbeck Group of uppermost Jurassic to lowermost Cretaceous age (Tithonian- Berriasian) outcrops mainly in the Purbeck area of Dorset, England. It was deposited in shallow freshwater to brackish lagoons with occasional marine incursions. Limestones, mainly biosparites, occur at 6 main levels. Differences in bed thickness, jointing and hardness make it suitable for a variety of purposes including dimension stone, monumental and ornamental stone, roofing tiles, paving, flooring and rockery stone. Near the top of the sequence is a dark gastropod biosparite, traditionally called Purbeck Marble, easily carved, which has been extensively used for decorative interior work in churches and cathedrals particularly for fonts, tombs, flooring and facings on columns for example in the medieval cathedrals of Salisbury, Exeter, Durham, York and Wells and Worcester and Westminster Abbey. The stone was extracted at least from Roman times (1st century AD) through the medieval period. Quarrying expanded from about 1700 reaching a peak in the late 18th and 19th centuries. Stone was transported first by sea but later by rail for wider use. Used in many local buildings, it gives an important element of local character. Many of the villages are designated conservation areas with a requirement for repair, maintenance and new building using local stone. Initially the stone was taken from quarries but was later mined. The number of operating companies declined from 15 to 5 over the past 40 years, with 10 active small quarries. Outputs are from few hundred tonnes to a few thousand tonnes per annum or about 9 to 12 years of permitted reserves but the Planning Authority intends to make sufficient provision for production at recent levels for their development plan period. The extraction sites are in an Area of Outstanding Natural Beauty and close to Jurassic Coast World Heritage Site. This might

Kidney Stones (For Parents)

Science.gov (United States)

... Staying Safe Videos for Educators Search English Español Kidney Stones KidsHealth / For Parents / Kidney Stones What's in ... other treatments to help remove the stones. How Kidney Stones Form It's the kidneys' job to remove ...

Fractomechanical Properties of As-Cast and Austempered SG Cast Iron Between -40 °C and +20 °C

Directory of Open Access Journals (Sweden)

V.E. Fierro

2002-06-01

Full Text Available The spheroidal graphite (SG cast iron fractomechanical response varies with the test temperature and with the microstructure parameters. In the present paper, we analyze this variation performing fractomechanical tests in a temperature range from -40°C to +20°C, doing also Charpy and tensile tests for material characterization. The tests were carried out on as-cast samples and heat treated samples to obtain an ADI grade 1. In both cases, we studied samples taken from two well differentiated "Y" block sizes. The results obtained show that, for the chemical composition analyzed, both castings have a fractomechanical response decrease as the temperature diminishes. Besides, the block size enlargement produce a deterioration of the mechanical properties (the fracture toughness, mainly, for both castings.

Calcium oxalate stone and gout.

Science.gov (United States)

Marickar, Y M Fazil

2009-12-01

Gout is well known to be produced by increased uric acid level in blood. The objective of this paper is to assess the relationship between gout and calcium oxalate stone formation in the humans. 48 patients with combination of gout and calcium oxalate stone problem were included. The biochemical values of this group were compared with 38 randomly selected uric acid stone patients with gout, 43 stone patients with gout alone, 100 calcium oxalate stone patients without gout and 30 controls, making a total of 259 patients. Various biochemical parameters, namely serum calcium, phosphorus and uric acid and 24-h urine calcium, phosphorus, uric acid, oxalate, citrate and magnesium were analysed. ANOVA and Duncan's multiple-range tests were performed to assess statistical significance of the variations. The promoters of stone formation, namely serum calcium (P stone patients and gouty calcium oxalate stone patients compared to the non-gouty patients and controls. Urine oxalate (P stones patients. The inhibitor urine citrate (P stone gouty patients, followed by the gouty uric acid stone formers and gouty calcium oxalate stone patients. The high values of promoters, namely uric acid and calcium in the gouty stone patients indicate the tendency for urinary stone formation in the gouty stone patients. There is probably a correlation between gout and calcium oxalate urinary stone. We presume this mechanism is achieved through the uric acid metabolism. The findings point to the summation effect of metabolic changes in development of stone disease.

Accuracy of endoscopic intraoperative assessment of urologic stone size.

Science.gov (United States)

Patel, Nishant; Chew, Ben; Knudsen, Bodo; Lipkin, Michael; Wenzler, David; Sur, Roger L

2014-05-01

Endoscopic treatment of renal calculi relies on surgeon assessment of residual stone fragment size for either basket removal or for the passage of fragments postoperatively. We therefore sought to determine the accuracy of endoscopic assessment of renal calculi size. Between January and May 2013, five board-certified endourologists participated in an ex vivo artificial endoscopic simulation. A total of 10 stones (pebbles) were measured (mm) by nonparticipating urologist (N.D.P.) with electronic calibers and placed into separate labeled opaque test tubes to prevent visualization of the stones through the side of the tube. Endourologists were blinded to the actual size of the stones. A flexible digital ureteroscope with a 200-μm core sized laser fiber in the working channel as a size reference was placed through the ureteroscope into the test tube to estimate the stone size (mm). Accuracy was determined by obtaining the correlation coefficient (r) and constructing an Altman-Bland plot. Endourologists tended to overestimate actual stone size by a margin of 0.05 mm. The Pearson correlation coefficient was r=0.924, with a p-valuestones (stones (≥4 mm), r=0.911 vs r=0.666. Altman-bland plot analysis suggests that surgeons are able to accurately estimate stone size within a range of -1.8 to +1.9 mm. This ex vivo simulation study demonstrates that endoscopic assessment is reliable when assessing stone size. On average, there was a slight tendency to overestimate stone size by 0.05 mm. Most endourologists could visually estimate stone size within 2 mm of the actual size. These findings could be generalized to state that endourologists are accurately able to intraoperatively assess residual stone fragment size to guide decision making.

Casting AISI 316 steel by gel cast

International Nuclear Information System (INIS)

Ozols, A; Thern, G; Rozenberg, S; Barreiro, M; Marajofsky, A

2004-01-01

The feasibility of producing AISI 316 steel components from their powders and avoiding their compaction is analyzed. A casting technique is tested that is similar to gel casting, used for ceramic materials. In the initial stage, the process consists of the formulation of a concentrated barbotine of powdered metal in a solution of water soluble organic monomers, which is cast in a mold and polymerized in situ to form a raw piece in the shape of the cavity. The process can be performed under controlled conditions using barbotines with a high monomer content from the acrylimide family. Then, the molded piece is slowly heated until the polymer is eliminated, and it is sintered at temperatures of 1160 o C to 1300 o C under a dry hydrogen atmosphere, until the desired densities are attained. The density and micro structure of the materials obtained are compared with those for the materials compacted and synthesized by the conventional processes. The preliminary results show the feasibility of the process for the production of certain kinds of structural components (CW)

An approach for the fatigue estimation of porous cast iron based on non-destructive testing results

Directory of Open Access Journals (Sweden)

Heinrietz André

2014-06-01

Full Text Available Big cast iron components made of spheroidal cast iron allow constructing big structures such as stone mills, engine blocks or wind mills with acceptable expenses. Thus, in economically optimized cast processes pores cannot be always prevented in thick walled cast iron components and these components are often rejected because of safety reasons. On the one hand the fatigue performance of high loadable spheroidal cast iron components is reduced significantly by the presence of local porosities which has been pointed out in the past. On the other hand concepts for the fatigue estimation based on fracture mechanics which take the size and localization of the defect into account can lead to erroneous estimations because the defect is modelled as a crack. The challenge of an estimation method is to derive a fatigue life without the necessity to perform component tests. In the contribution an estimation method is presented which is able to determine the fatigue strength of a material volume taking the pores into account. The method can be applied based on data from computer tomographic X-ray (CT or Sampling Phased Array (SPA ultrasonic analyses. The method is presented for three spheroidal cast iron types: ferritic GJS-400-18, ferritic GJS-450-15 with high silicon content and perlitic GJS-700-3.

Acute management of stones

DEFF Research Database (Denmark)

Jung, Helene; Osther, Palle J S

2015-01-01

INTRODUCTION: Stone management is often conservative due to a high spontaneous stone passage rate or non-symptomatic calyceal stones that do not necessarily require active treatment. However, stone disease may cause symptoms and complications requiring urgent intervention. MATERIAL AND METHODS: I...... with careful consideration of stone size and location, symptoms, patient comorbidity and radiation dose. CONCLUSION: In case of infective hydronephrosis, compromised renal function or persistent pain despite adequate analgesic treatment acute intervention is indicated....

Colour Metallography of Cast Iron - Chapter 3: Spheroidal Graphite Cast Iron (Ⅳ

Directory of Open Access Journals (Sweden)

Zhou Jiyang

2010-11-01

Full Text Available Cast iron, as a traditional metal material, has advantages of low total cost, good castability and machinability, good wear resistance and low notch sensitivity, and is still facing tough challenge in quality, property and variety of types etc. Experts and engineers studying and producing iron castings all around world extremely concern this serious challenge. Over more than 30 years, a great of research work has been carried out on how to further improve its property, expand its application and combine cast iron technology with some hi-techs (for example, computer technology. Nevertheless, cast iron is a multi-element and multi-phase alloy and has complex and variety of structures and still has great development potential in structure and property. For further studying and developing cast iron, theoretical research work is important promise, and the study on solidification process and control mechanism of graphite morphology is fundamental for improving property of cast iron and developing new type of cast iron. Metallography of cast iron normally includes two sections: liquid phase transformation and solid phase transformation. The book, Colour Metallography of Cast Iron, uses colour metallography technique to study solidification structures of cast irons: graphite, carbides, austenite and eutectics; and focuses on solidification processes. With progress of modern solidification theory, the control of material solidification process becomes important measure for improving traditional materials and developing new materials. Solidification structure not only influences mechanical and physical properties of cast iron, but also affects its internal quality. The book uses a large amount of colour photos to describe the formation of solidification structures and their relations. Crystallization phenomena, which cannot be displayed with traditional metallography, are presented and more phase transformation information is obtained from these colour

Colour Metallography of Cast Iron - Chapter 3: Spheroidal Graphite Cast Iron (Ⅰ

Directory of Open Access Journals (Sweden)

Zhou Jiyang

2010-02-01

Full Text Available Cast iron, as a traditional metal material, has advantages of low total cost, good castability and machinability, good wear resistance and low notch sensitivity, and is still facing tough challenge in quality, property and variety of types etc. Experts and engineers studying and producing iron castings all around world extremely concern this serious challenge. Over more than 30 years, a great of research work has been carried out on how to further improve its property, expand its application and combine cast iron technology with some hi-techs (for example, computer technology. Nevertheless, cast iron is a multi-element and multi-phase alloy and has complex and variety of structures and still has great development potential in structure and property. For further studying and developing cast iron, theoretical research work is important promise, and the study on solidification process and control mechanism of graphite morphology is fundamental for improving property of cast iron and developing new type of cast iron. Metallography of cast iron normally includes two sections: liquid phase transformation and solid phase transformation. The book, Colour Metallography of Cast Iron, uses colour metallography technique to study solidification structures of cast irons: graphite, carbides, austenite and eutectics; and focuses on solidification processes. With progress of modern solidification theory, the control of material solidification process becomes important measure for improving traditional materials and developing new materials. Solidification structure not only influences mechanical and physical properties of cast iron, but also affects its internal quality. The book uses a large amount of colour photos to describe the formation of solidification structures and their relations. Crystallization phenomena, which cannot be displayed with traditional metallography, are presented and more phase transformation information is obtained from these colour

Colour Metallography of Cast Iron - Chapter 4: Vermicular Graphite Cast Iron (Ⅱ

Directory of Open Access Journals (Sweden)

Zhou Jiyang

2011-05-01

Full Text Available Cast iron, as a traditional metal material, has advantages of low total cost, good castability and machinability, good wear resistance and low notch sensitivity, and is still facing tough challenge in quality, property and variety of types etc. Experts and engineers studying and producing iron castings all around world extremely concern this serious challenge. Over more than 30 years, a great of research work has been carried out on how to further improve its property, expand its application and combine cast iron technology with some hi-techs (for example, computer technology. Nevertheless, cast iron is a multi-element and multi-phase alloy and has complex and variety of structures and still has great development potential in structure and property. For further studying and developing cast iron, theoretical research work is important promise, and the study on solidification process and control mechanism of graphite morphology is fundamental for improving property of cast iron and developing new type of cast iron. Metallography of cast iron normally includes two sections: liquid phase transformation and solid phase transformation. The book, Colour Metallography of Cast Iron, uses colour metallography technique to study solidification structures of cast irons: graphite, carbides, austenite and eutectics; and focuses on solidification processes. With progress of modern solidification theory, the control of material solidification process becomes important measure for improving traditional materials and developing new materials. Solidification structure not only influences mechanical and physical properties of cast iron, but also affects its internal quality. The book uses a large amount of colour photos to describe the formation of solidification structures and their relations. Crystallization phenomena, which cannot be displayed with traditional metallography, are presented and more phase transformation information is obtained from these colour

Treatment of gallbladder stone with common bile duct stones in the laparoscopic era

OpenAIRE

Zhang, Wei-jie; Xu, Gui-fang; Huang, Qin; Luo, Kun-lun; Dong, Zhi-tao; Li, Jie-ming; Wu, Guo-zhong; Guan, Wen-xian

2015-01-01

Background: Laparoscopic common bile duct exploration (LCBDE) for stone can be carried out by either laparoscopic transcystic stone extraction (LTSE) or laparoscopic choledochotomy (LC). It remains unknown as to which approach is optimal for management of gallbladder stone with common bile duct stones (CBDS) in Chinese patients. Methods: From May 2000 to February 2009, we prospective treated 346 consecutive patients with gallbladder stones and CBDS with laparoscopic cholecystectomy and LCBDE....

Comparison of mechanical properties and microstructural characterization of CoCrMo alloy obtained via selective laser melting (SLM) and casting techniques

Energy Technology Data Exchange (ETDEWEB)

Mergulhao, Marcello Vertamatti; Podesta, Carlos Eduardo; Neves, Mauricio David Martins das, E-mail: marcellovertamatti@usp.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2016-07-01

Full text: Advances in processes using the powder metallurgy techniques are making this technology competitive compared to the other traditional manufacturing processes, especially in medicine area. The additive manufacturing technique - selective laser melting (SLM) was applied in a biomaterial of CoCrMo alloy (ASTM F75), to study the mechanical properties and microstructural characterization in comparison between the conventional technique - lost wax casting. The gas atomized powder was investigated by their physical (as apparent density, bulk density and flow rate) and the chemical properties (SEM-EDS and X-ray fluorescence). Specimens of standard samples were manufactured using these techniques to evaluate the mechanical properties as yield strength, maximum tensile, rupture tensile, elongation, elastic modulus, transverse rupture strength and the Vickers hardness. Before the mechanical tests the microstructure of specimens were examined using optical microscope (OM) and SEM-EDS. The results of mechanical properties showed a higher values in the SLM specimens compared with the obtained in the cast specimens. The micrographs revealed a typical morphology of consolidation process, like as the characterized by selected layer used in the SLM technique and the primary and secondary dendrites arms in the casting technique. (author)

Metabolic Characteristics and Risks Associated with Stone Recurrence in Korean Young Adult Stone Patients.

Science.gov (United States)

Kang, Ho Won; Seo, Sung Pil; Kim, Won Tae; Kim, Yong-June; Yun, Seok-Joong; Kim, Wun-Jae; Lee, Sang-Cheol

2017-08-01

The aim of this study was to assess the metabolic characteristics and risks of stone recurrence in young adult stone patients in Korea. The medical records of 1532 patients presenting with renal or ureteric stones at our stone clinic between 1994 and 2015 were retrospectively reviewed. Patients were grouped according to age (young adult, 18-29 years; intermediate onset, 30-59 years; old age, ≥60 years) at first presentation, and measurements of clinicometabolic characteristics and risks of stone recurrence were compared. Overall, excretion of urinary stone-forming substances was highest in the intermediate onset group, followed by the young adult and old age groups. Importantly, excretion of urinary citrate was lowest in the young adult group. Kaplan-Meier analyses identified a significant difference between the three age groups in terms of stone recurrence (log rank test, p adult stone patients. Younger age (18-29 years) at first stone presentation was a significant risk factor for stone recurrence, and urinary citrate excretion was an independent risk factor affecting recurrence in this group. Metabolic evaluation and potassium citrate therapy should be considered for young adult stone patients to prevent recurrence.

Percutaneous suprapubic stone extraction for posterior urethral stones in children: efficacy and safety.

Science.gov (United States)

Safwat, Ahmed S; Hameed, Diaa A; Elgammal, Mohamed A; Abdelsalam, Yasser M; Abolyosr, Ahmad

2013-08-01

To evaluate the safety and efficacy of percutaneous suprapubic stone extraction (PSPSE) for pediatric posterior urethral stones. Between July 2007 and June 2010, 54 boys presenting with acute urinary retention due to posterior urethral stones underwent PSPSE. Patients were a mean age of 66.4 months (range, 8-180 months). The stone size was 0.7-1.9 cm. Patients were placed under general anesthesia, and a 7F urethroscope was used to pushback the stone to the bladder. A 3-mm suprapubic puncture with a scalpel was performed, followed by insertion of a straight narrow hemostat through the puncture aided with cystoscopic guidance. The stone was grasped with the hemostat in its narrowest diameter and was extracted percutaneously or crushed if friable. The suprapubic puncture was closed with a single 4-0 Vicryl (Ethicon) suture. Intact stone retrieval was achieved in 45 patients, and the stone was crushed into minute fragments in 9 patients. Intraperitoneal extravasation developed in 1 patient that required open surgical intervention. Mean operative time was 22 minutes. Patients were monitored for up to 17 months, with complete resolution of symptoms and stone clearance. PSPSE provides a minimally invasive approach for the extraction of urethral and bladder stones in the pediatric population. The use of a straight hemostat for suprapubic stone extraction or crushing is a good alternative to suprapubic tract dilation, with minimal morbidity. Copyright © 2013 Elsevier Inc. All rights reserved.

Accuracy of stereolithography additive casts used in a digital workflow

DEFF Research Database (Denmark)

Al-Imam, Hiba; Gram, Mia; Benetti, Ana R

2018-01-01

additive (SLA) casts from 2 manufacturers: 9 Dreve SLA casts and 9 Scanbiz SLA casts. All casts were then scanned 9 times with an extraoral scanner to produce the reference data set. Trueness was evaluated by superimposing the data sets obtained by scanning the casts with the reference data set. Precision...

EVALUATION OF CONSISTENCY AND SETTING TIME OF IRANIAN DENTAL STONES

Directory of Open Access Journals (Sweden)

F GOL BIDI

2000-09-01

Full Text Available Introduction. Dental stones are widely used in dentistry and the success or failure of many dental treatments depend on the accuracy of these gypsums. The purpose of this study was the evaluation of Iranian dental stones and comparison between Iranian and foreign ones. In this investigation, consistency and setting time were compared between Pars Dendn, Almas and Hinrizit stones. The latter is accepted by ADA (American Dental Association. Consistency and setting time are 2 of 5 properties that are necessitated by both ADA specification No. 25 and Iranian Standard Organization specification No. 2569 for evaluation of dental stones. Methods. In this study, the number and preparation of specimens and test conditions were done according to the ADA specification No. 25 and all the measurements were done with vicat apparatus. Results. The results of this study showed that the standard consistency of Almas stone was obtained by 42ml water and 100gr powder and the setting time of this stone was 11±0.03 min. Which was with in the limits of ADA specification (12±4 min. The standard consistency of Pars Dandan stone was obrianed by 31ml water and 100 gr powder, but the setting time of this stone was 5± 0.16 min which was nt within the limits of ADA specification. Discussion: Comparison of Iranian and Hinrizit stones properties showed that two probable problems of Iranian stones are:1- Unhemogrnousity of Iranian stoned powder was caused by uncontrolled temperature, pressure and humidity in the production process of stone. 2- Impurities such as sodium chloride was responsible fo shortening of Pars Dendens setting time.

Stone composition and metabolic status.

Science.gov (United States)

Bibilash, B S; Vijay, Adarsh; Fazil Marickar, Y M

2010-06-01

This paper aims to study the correlation between biochemical risk factors of the stone former and the type of oxalate stone formed, namely calcium oxalate monohydrate (COM) and calcium oxalate dehydrate (COD). A retrospective study of 487 patients who had been attending the urinary stone clinic, Trivandrum during 1998-2007 was conducted. The stones retrieved from them were subjected to chemical analysis and FTIR spectrographic analysis. They were categorized into COM, COD, mixed COM+COD and others. Of 142 pure calcium oxalate stone patients, 87 were predominantly COM stone formers and 55 COD stone formers. Their metabolic status of 24 h urine and serum was assessed. The values of urine calcium, phosphorus, uric acid, magnesium, creatinine, oxalate, citric acid, sodium and potassium, serum values of calcium, phosphorus, uric acid, magnesium and creatinine and calculated values of creatinine clearance, tubular reabsorption of phosphate, calcium magnesium ratio and calcium oxalate ratio were recorded. Comparison was made between the COM stone group and the COD stone group. Patients forming COM stones had significantly higher mean values for urine calcium (P stone forming patients. All other values failed to show significant difference. Patients, with higher urine oxalate, formed COM stones. Those with low magnesium (which is an inhibitor) formed more of COD stones. Urine calcium was high in both groups without showing significant variation from the mean. In patients with high calcium-oxalate and calcium-magnesium ratios, there is higher chance of forming a COD stone than COM. Identification of the crystallization pattern of the calcium stone will help in selecting treatment modalities.

IGCP 637 Heritage Stone Designation: A UNESCO and IUGS project on natural stones

Science.gov (United States)

Pereira, Dolores; Cooper, Barry; Schouenborg, Björn; Marker, Brian; Kramar, Sabina

2017-04-01

IGCP 637 was approved in 2015 to facilitate establishment of a new international geological standard for building and ornamental stones. Formal international recognition of those natural stone types that have achieved widespread utilization in human culture is now underway and the term "Global Heritage Stone Resource" (GHSR) has been proposed for this designation. Stones that have been used in heritage construction, sculptural masterpieces, as well as in utilitarian (yet culturally important) applications are obvious GHSR candidates. In co-ordination with these aims the project has an associated role to promote the adoption and use of the GHSR designation. Consequently an interim list of potential GHSRs is maintained and a register of GHSR approved stones is being created. IGCP 637 also enhances the capacity of the International Union of Geological Sciences (IUGS) in the realm of dimension stone and geological standards as it is the first IUGS involvement in this subject. As a consequence, the largest known international grouping of dimension stone professionals has been established. Within IGCP 637 a web page has been created at www.globalheritagestone.com, including information on the Working Group and also specific information on the evolution of the project. Several researchers were funded to attend the Heritage Stone working group activities, including researchers from Algeria, Malawi, India, Italy and Russia. We also have produced many publications, both as individual papers and special issues in journals included in the Journal Citation Reports. Monographs are being prepared at present. Hopefully, IGCP 637 will help to widen the circle of researchers interested in natural stones as part of our geoheritage. Heritage Stone references: articles and special issues - Pereira, D. and Marker, B. (2016) The value of original natural stone in the context of architectural heritage. Geosciences, 6, 13. - Heritage Stone 1. Ed. Pereira and Pratt. (2016). Geoscience

Papillary Ductal Plugging is a Mechanism for Early Stone Retention in Brushite Stone Disease

DEFF Research Database (Denmark)

Williams, James C; Borofsky, Michael S; Bledsoe, Sharon B

2018-01-01

PURPOSE: Mechanisms of early stone retention in the kidney are under studied and poorly understood. To date attachment via Randall's plaque is the only widely accepted theory in this regard, which is best described in idiopathic calcium oxalate stone formers. Brushite stone formers are known...... to have distinct papillary morphology relative to calcium oxalate stone formers. As such we sought to determine whether stone attachment mechanisms in such patients may be similarly unique. MATERIALS AND METHODS: Patients undergoing percutaneous and or ureteroscopic procedures for stone removal consented...... to endoscopic renal papillary examination and individual stone collection. Each removed stone was processed using micro computerized tomography to assess the 3-dimensional microstructure and the minerals contained, and search for common structural features indicative of novel mechanisms of early growth...

Shock Wave Lithotripsy in Ureteral Stones: Evaluation of Patient and Stone Related Predictive Factors

Directory of Open Access Journals (Sweden)

Ozgur Yazici

2015-08-01

Full Text Available ABSTRACTPurpose:To evaluate the patient and stone related factors which may influence the final outcome of SWL in the management of ureteral stones.Materials and Methods:Between October 2011 and October 2013, a total of 204 adult patients undergoing SWL for single ureteral stone sizing 5 to 15 mm were included into the study program. The impact of both patient (age, sex, BMI, and stone related factors (laterality, location, longest diameter and density as CT HU along with BUN and lastly SSD (skin to stone distance on fragmentation were analysed by univariate and multivariate analyses. Results: Stone free rates for proximal and distal ureteral stones were 68.8% and 72.7%, respectively with no statistically significant difference between two groups (p=0.7. According to univariate and multivariate analyses, while higher BMI (mean: 26.8 and 28.1, p=0.048 and stone density values (mean: 702 HU and 930 HU, p<0.0001 were detected as statistically significant independent predictors of treatment failure for proximal ureteral stones, the only statistically significant predicting parameter for the success rates of SWL in distal ureteral stones was the higher SSD value (median: 114 and 90, p=0.012.Conclusions:Our findings have clearly shown that while higher BMI and increased stone attenuation values detected by NCCT were significant factors influencing the final outcome of SWL treatment in proximal ureteral stones; opposite to the literature, high SSD was the only independent predictor of success for the SWL treatment of distal ureteral stones.

Engineering design of centrifugal casting machine

Science.gov (United States)

Kusnowo, Roni; Gunara, Sophiadi

2017-06-01

Centrifugal casting is a metal casting process in which metal liquid is poured into a rotating mold at a specific temperature. Given round will generate a centrifugal force that will affect the outcome of the casting. Casting method is suitable in the manufacture of the casting cylinder to obtain better results. This research was performed to design a prototype machine by using the concept of centrifugal casting. The design method was a step-by-step systematic approach in the process of thinking to achieve the desired goal of realizing the idea and build bridges between idea and the product. Design process was commenced by the conceptual design phase and followed by the embodiment design stage and detailed design stage. With an engineering design process based on the method developed by G. E. Dieter, draft prototype of centrifugal casting machine with dimension of 550×450×400 mm, ¼ HP motor power, pulley and belt mechanism, diameter of 120-150mm, simultaneously with the characteristics of simple casting product, easy manufacture and maintenance, and relatively inexpensive, was generated.

The effect of pouring time on the dimensional accuracy of casts made from different irreversible hydrocolloid impression materials

Directory of Open Access Journals (Sweden)

Supneet Singh Wadhwa

2013-01-01

Full Text Available Aims and Objectives: To determine the time dependent accuracy of casts made from three different irreversible hydrocolloids. Materials and Methods: The effect of delayed pouring on the accuracy of three different irreversible hydrocolloid impression materials - Regular set CA 37(Cavex, The Netherlands, regular set chromatic (Jeltrate, Dentsply, and fast set (Hydrogum soft, Zhermack Clinical was investigated. A brass master die that contained two identical posts simulating two complete crown-tapered abutment preparations with reference grooves served as a standardized master model. A total of 120 impressions were made using specially prepared stock-perforated brass tray with 40 impressions of each material. The impressions were further sub-grouped according to four different storage time intervals: 0 min (immediately, 12 min, 30 min, and 1 h. The impressions were stored at room temperature in a zip-lock plastic bag. Interabutment and intraabutment distances were measured in the recovered stone dies (Type IV, Kalrock using a profile projector with an accuracy of 0.001 mm. The data so obtained was analyzed statistically. Results: Results of this study showed no statistically significant differences in the accuracy of casts obtained at different time intervals. Conclusion: Because it is not always possible to pour the impression immediately in routine clinical practice, all irreversible hydrocolloid materials studied could be stored in a zip-lock plastic bag for upto 1 h without any significant distortion.

Comparison of the passivity between cast alloy and laser-welded titanium overdenture bars.

Science.gov (United States)

Paiva, Jose; Givan, Daniel A; Broome, James C; Lemons, Jack E; McCracken, Michael S

2009-12-01

The purpose of this study was to investigate the fit of cast alloy overdenture and laser-welded titanium-alloy bars by measuring induced strain upon tightening of the bars on a master cast as well as a function of screw tightening sequence. Four implant analogs were secured into Type IV dental stone to simulate a mandibular edentulous patient cast, and two groups of four overdenture bars were fabricated. Group I was four cast alloy bars and Group II was four laser-welded titanium bars. The cast alloy bars included Au-Ag-Pd, Pd-Ag-Au, Au-Ag-Cu-Pd, and Ag-Pd-Cu-Au, while the laser-welded bars were all Ti-Al-V alloy. Bars were made from the same master cast, were torqued into place, and the total strain in the bars was measured through five strain gauges bonded to the bar between the implants. Each bar was placed and torqued 27 times to 30 Ncm per screw using three tightening sequences. Data were processed through a strain amplifier and analyzed by computer using StrainSmart software. Data were analyzed by ANOVA and Tukey's post hoc test. Significant differences were found between alloy types. Laser-welded titanium bars tended to have lower strains than corresponding cast bars, although the Au-Ag-Pd bar was not significantly different. The magnitudes of total strain were the least when first tightening the ends of the bar. The passivity of implant overdenture bars was evaluated using total strain of the bar when tightening. Selecting a high modulus of elasticity cast alloy or use of laser-welded bar design resulted in the lowest average strain magnitudes. While the effect of screw tightening sequence was minimal, tightening the distal ends first demonstrated the lowest strain, and hence the best passivity.

Retrograde intrarenal stone surgery for extracorporeal shock-wave lithotripsy-resistant kidney stones

DEFF Research Database (Denmark)

Jung, Helene; Nørby, Bettina; Osther, Palle Jörn

2006-01-01

OBJECTIVE: The newer flexible ureteroscopes, 150-200-microm holmium YAG laser fibres and superflexible Dormia baskets have made it possible to reach and treat stones in all parts of the kidney. The object of this evaluation was to study the outcome of retrograde intrarenal stone surgery (RIRS......) for extracorporeal shock-wave lithotripsy (ESWL)-resistant kidney stones. MATERIAL AND METHODS: A total of 38 consecutive patients (18 males, 20 females) participated in the study. All patients had undergone ESWL prior to RIRS without success. In all cases the stones could be reached with the endoscope. Calculi...... ranged in size from 3 to 20 mm (mean 9 mm). In 32 cases the stones were fragmented using a holmium YAG laser and in six the stones could be extracted using zero-tip Dormia baskets without fragmentation. Sixteen patients had lower calyceal calculi and eight had an abnormal anatomy of the upper urinary...

Chemical Resistance of Ornamental Compound Stone Produced with Marble Waste and Unsaturated Polyester

Science.gov (United States)

Ribeiro, Carlos E. Gomes; Rodriguez, Rubén J. Sánchez; Vieira, Carlos M. Fontes

Ornamental compound stone are produced by industry for decades, however, few published studies describe these materials. Brazil has many deposits of stone wastes and a big potential to produce these materials. This work aims to evaluate the chemical resistance of ornamental compound stones produced with marble waste and unsaturated polyester. An adaptation of Annex H of ABNT NBR 13818:97 standard, with reagents commonly used in household products, was used. The results were compared with those obtained for natural stone used in composite production.

Factors affecting stone-free rate and complications of percutaneous nephrolithotomy for treatment of staghorn stone.

Science.gov (United States)

el-Nahas, Ahmed R; Eraky, Ibrahim; Shokeir, Ahmed A; Shoma, Ahmed M; el-Assmy, Ahmed M; el-Tabey, Nasr A; Soliman, Shady; Elshal, Ahmed M; el-Kappany, Hamdy A; el-Kenawy, Mahmoud R

2012-06-01

To determine factors affecting the stone-free rate and complications of percutaneous nephrolithotomy (PNL) for treatment of staghorn stones. The computerized database of patients who underwent PNL for treatment of staghorn stones between January 2003 and January 2011 was reviewed. All perioperative complications were recorded and classified according to modified Clavien classification system. The stone-free rate was evaluated with low-dose noncontrast computed tomography (CT). Univariate and multivariate statistical analyses were performed to determine factors affecting stone-free and complication rates. The study included 241 patients (125 male and 116 female) with a mean age of 48.7 ±14.3 years. All patients underwent 251 PNL (10 patients had bilateral stones). The stone-free rate of PNL monotherapy was 56% (142 procedures). At 3 months, the stone-free rate increased to 73% (183 kidneys) after shock wave lithotripsy. Independent risk factors for residual stones were complete staghorn stone and presence of secondary calyceal stones (relative risks were 2.2 and 3.1, respectively). The complication rate was 27% (68 PNL). Independent risk factors for development of complications were performance of the procedure by urologists other than experienced endourologist and positive preoperative urine culture (relative risks were 2.2 and 2.1, respectively). Factors affecting the incidence of residual stones after PNL are complete staghorn stones and the presence of secondary calyceal stones. Complications are significantly high if PNL is not performed by an experienced endourologist or if preoperative urine culture is positive. Copyright © 2012 Elsevier Inc. All rights reserved.

New data on painted stone slabs from Southern Peru

OpenAIRE

Faron-Bartels, Renata

2011-01-01

After analysing museum collections, studying bibliographical sources and undertaking two surface prospections at Pampacolca the author carried out the archaeological project “Lajas Pintadas de Pampacolca” (painted stone slabs from Pampacolca) in August and September 2001 with the objective of investigating these stones or rather the painted ceramic boards in more detail. The essential task set for this project consisted in obtaining artefacts from preferably undisturbed contexts at various ar...

Kidney stones - self-care

Science.gov (United States)

... self-care; Nephrolithiasis and self-care; Stones and kidney - self-care; Calcium stones and self-care; Oxalate ... provider or the hospital because you have a kidney stone. You will need to take self-care ...

Temperature and microstructure characteristics of silumin casting AlSi9 made with investment casting method

Directory of Open Access Journals (Sweden)

S. Pietrowski

2011-07-01

Full Text Available This work presents the research result of the temperature distribution and the microstructure in certain parts of the field-glass body frame casting made from silumin AlSi9 using the investment casting method in the ceramic mould. It was proved that the highest temperature of the silumin appears in the sprue in which the silumin is in the liquid-solid state, though the process of silumin crystallization in the casting is finished. It was stated that in certain elements of the casting the side opposite to the runner crystallizes and cools fastest. The differences in the rate of crystalline growth and cooling of certain casting elements cause differ- ent microstructure in them which can also influence the mechanic properties.It is necessary to state that the temperature of the initial heating of the ceramic mold equal to 60oC guarantees obtaining of the castings without defects and of little porosity. Incomplete modification of the silumin with strontium causes silica precipitation to appear close to the spherical ones.

Pitfalls in urinary stone identification using CT attenuation values: Are we getting the same information on different scanner models?

Energy Technology Data Exchange (ETDEWEB)

Grosjean, Romain, E-mail: r.grosjean@chu-nancy.fr [IADI Laboratory, INSERM-U947, Nancy-University, Allée du Morvan, 54500 Vandoeuvre-les-Nancy (France); Daudon, Michel, E-mail: michel.daudon@tnn.aphp.fr [IADI Laboratory, INSERM-U947, Nancy-University, Allée du Morvan, 54500 Vandoeuvre-les-Nancy (France); Chammas, Mario F., E-mail: mariochammas@usp.br [University of Sao Paulo – Division of Urology, Av. Dr. Enéas de Carvalho Aguiar, 255, 7" o Andar – s. 7123, São Paulo (Brazil); Claudon, Michel, E-mail: m.claudon@chu-nancy.fr [IADI Laboratory, INSERM-U947, Nancy-University, Allée du Morvan, 54500 Vandoeuvre-les-Nancy (France); Eschwege, Pascal, E-mail: peschwege@yahoo.com [Department of Urology, Brabois Hospital, University Hospital of Nancy, Allée du Morvan, 54511 Vandoeuvre-les-Nancy (France); Felblinger, Jacques, E-mail: j.felblinger@chu-nancy.fr [IADI Laboratory, INSERM-U947, Nancy-University, Allée du Morvan, 54500 Vandoeuvre-les-Nancy (France); Hubert, Jacques, E-mail: j.hubert@chu-nancy.fr [Department of Urology, Brabois Hospital, University Hospital of Nancy, Allée du Morvan, 54511 Vandoeuvre-les-Nancy (France)

2013-08-15

Introduction: Evaluate the capability of different Computed Tomography scanners to determine urinary stone compositions based on CT attenuation values and to evaluate potential differences between each model. Methods: 241 human urinary stones were obtained and their biochemical composition determined. Four different CT scanners (Siemens, Philips, GEMS and Toshiba) were evaluated. Mean CT-attenuation values and the standard deviation were recorded separately and compared with a t-paired test. Results: For all tested CT scanners, when the classification of the various types of stones was arranged according to the mean CT-attenuation values and to the confidence interval, large overlappings between stone types were highlighted. The t-paired test showed that most stone types could not be identified. Some types of stones presented mean CT attenuation values significantly different from one CT scanner to another. At 80 kV, the mean CT attenuation values obtained with the Toshiba Aquilion were significantly different from those obtained with the Siemens Sensation. On the other hand, mean values obtained with the Philips Brilliance were all significantly equal to those obtained with the Siemens Sensation and with the Toshiba Aquilion. At 120 kV mean CT attenuation values of uric acid, cystine and struvite stones obtained with the Philips model are significantly different from those obtained with the Siemens and the Toshiba but equal to those obtained with the GE 64. Conclusions: According to our study, there is a great variability when different brands and models of scanners are compared directly. Furthermore, the CT scan analysis and HU evaluation appears to gather insufficient information in order to characterize and identify the composition of renal stones.

Pitfalls in urinary stone identification using CT attenuation values: Are we getting the same information on different scanner models?

International Nuclear Information System (INIS)

Grosjean, Romain; Daudon, Michel; o Andar – s. 7123, São Paulo (Brazil))" data-affiliation=" (University of Sao Paulo – Division of Urology, Av. Dr. Enéas de Carvalho Aguiar, 255, 7o Andar – s. 7123, São Paulo (Brazil))" >Chammas, Mario F.; Claudon, Michel; Eschwege, Pascal; Felblinger, Jacques; Hubert, Jacques

2013-01-01

Introduction: Evaluate the capability of different Computed Tomography scanners to determine urinary stone compositions based on CT attenuation values and to evaluate potential differences between each model. Methods: 241 human urinary stones were obtained and their biochemical composition determined. Four different CT scanners (Siemens, Philips, GEMS and Toshiba) were evaluated. Mean CT-attenuation values and the standard deviation were recorded separately and compared with a t-paired test. Results: For all tested CT scanners, when the classification of the various types of stones was arranged according to the mean CT-attenuation values and to the confidence interval, large overlappings between stone types were highlighted. The t-paired test showed that most stone types could not be identified. Some types of stones presented mean CT attenuation values significantly different from one CT scanner to another. At 80 kV, the mean CT attenuation values obtained with the Toshiba Aquilion were significantly different from those obtained with the Siemens Sensation. On the other hand, mean values obtained with the Philips Brilliance were all significantly equal to those obtained with the Siemens Sensation and with the Toshiba Aquilion. At 120 kV mean CT attenuation values of uric acid, cystine and struvite stones obtained with the Philips model are significantly different from those obtained with the Siemens and the Toshiba but equal to those obtained with the GE 64. Conclusions: According to our study, there is a great variability when different brands and models of scanners are compared directly. Furthermore, the CT scan analysis and HU evaluation appears to gather insufficient information in order to characterize and identify the composition of renal stones

Spatial Bimetallic Castings Manufactured from Iron Alloys

Directory of Open Access Journals (Sweden)

M. Cholewa

2007-07-01

Full Text Available In this paper a conception for manufacturing method of skeleton castings with composite features was shown. Main application of such castings are the working organs of machines subjected to intensive abrasive and erosive wear. Skeleton geometry was based on three-dimensional cubic net consisting of circular connectors and nodes joining 6 connectors according to Cartesian co-ordinate system. Dimension of an elementary cell was equal to 10 mm and diameter of single connector was equal to 5 mm. For bimetallic castings preparation two Fe based alloys were used: L25SHMN cast steel for skeleton substrate and ZlCr15NiMo cast iron for working part of the casting. In presented work obtained structure was analyzed with indication of characteristic regions. Authors described phenomena occurring at the alloys interface and phases in transition zone. A thesis was formulated concerning localization of transition zone at the cast iron matrix – cast steel reinforcement interface. Direction of further studies were indicated.

The early days of surgery for stones in the bladder.

Science.gov (United States)

Ellis, Harold

2011-05-01

Man has suffered from bladder stones since the earliest times. The oldest specimen of a bladder stone so far discovered was obtained at the excavation of a grave of a boy of about 16 in an ancient Egyptian burial ground and was dated at around 4800 BC. Of the triad of 'elective" operations first performed by our surgical forefathers--circumcision, trephination of the skull and cutting for the stone--only the last was for a purely surgical indication and not for religious or ritual reasons; it may safely be pronounced as the most ancient operation performed for a specific surgical pathology.

Canada's National Building Stone: Tyndall Stone from Manitoba

Science.gov (United States)

Pratt, Brian R.; Young, Graham A.; Dobrzanski, Edward P.

2016-04-01

Tyndall Stone is a distinctively mottled and highly fossiliferous dolomitic limestone that belongs to the Selkirk Member of the Red River Formation, of Late Ordovician (Katian) age. It has been quarried at Garson, Manitoba, 37 km northeast of Winnipeg, since 1895, although other quarries in the area go back to 1832. Tyndall Stone, so named because it was shipped by rail from nearby Tyndall, is currently produced by Gillis Quarries Limited. It has various uses as a dimension stone. Large slabs, most often cut parallel to bedding, face the exterior or interior of many important buildings such as the Parliament Buildings and the Canadian Museum of Civilization in the Ottawa area, the Empress Hotel in Victoria, and the provincial legislatures in Winnipeg and Regina, as well as many commercial buildings especially in the Canadian prairies. At the quarries, the stone is cut vertically, using eight foot (2.44 m) diameter saws mounted on one hundred foot (30.5 m) tracks, then split into 6-8 tonne blocks that are moved using front-end loaders. Gillis Quarries operates a large finishing plant with an area of about 4000 m2. Stone is processed along advanced cutting lines that feature eight primary saws and six gantry saw stations, allowing it to be made into a variety of sizes, shapes, and finishes. The Selkirk Member is 43 m thick and the stone is extracted from a 6-8 m thick interval within the lower part. The upper beds tend to be more buff-coloured than the grey lower beds due to weathering by groundwater. The stone is massive, but extracted blocks are less than ~1m thick due to splitting along stylolites. Consisting of bioturbated wackestone to packstone, the Tyndall Stone was deposited in a shallow-marine environment within the photic zone, in the central part of the vast equatorial epicontinental sea that covered much of Laurentia. Scattered thin, bioclastic grainstone lenses record brief, low-energy storm events. The distinctive mottles are formed by dolomitized

Bilayered container << stone-concrete >> to store toxic materials and radioactive waste.; Dvukhslojnyj kontejner << kamen` - beton >> dlya khraneniya toksichnykh materialov i radioaktivnykh otkhodov.

Energy Technology Data Exchange (ETDEWEB)

Vagin, V V; Koltunov, B G; Kurylo, D A; Kosyak, A T; Izotov, Yu L [Dnepropetrovskij Inst. Chernoj Metallurgii, Dnepropetrovsk (Ukraine)

1994-12-31

A design of a universal container providing for the storage of toxic and radioactive waste with the hydrogen index from 2 to 12 pH has been developed. The construction is based on the lining of stone casting with high density and corrosion-resistance indices ensuring leak-proofness and operation reliability of the container under long terms of storage of agressive materials.

Kidney stone erosion by micro scale hydrodynamic cavitation and consequent kidney stone treatment.

Science.gov (United States)

Perk, Osman Yavuz; Şeşen, Muhsincan; Gozuacik, Devrim; Koşar, Ali

2012-09-01

The objective of this study is to reveal the potential of micro scale hydrodynamic bubbly cavitation for the use of kidney stone treatment. Hydrodynamically generated cavitating bubbles were targeted to the surfaces of 18 kidney stone samples made of calcium oxalate, and their destructive effects were exploited in order to remove kidney stones in in vitro experiments. Phosphate buffered saline (PBS) solution was used as the working fluid under bubbly cavitating conditions in a 0.75 cm long micro probe of 147 μm inner diameter at 9790 kPa pressure. The surface of calcium oxalate type kidney stones were exposed to bubbly cavitation at room temperature for 5 to 30 min. The eroded kidney stones were visually analyzed with a high speed CCD camera and using SEM (scanning electron microscopy) techniques. The experiments showed that at a cavitation number of 0.017, hydrodynamic bubbly cavitation device could successfully erode stones with an erosion rate of 0.31 mg/min. It was also observed that the targeted application of the erosion with micro scale hydrodynamic cavitation may even cause the fracture of the kidney stones within a short time of 30 min. The proposed treatment method has proven to be an efficient instrument for destroying kidney stones.

Nodular cast iron and casting monitoring

Directory of Open Access Journals (Sweden)

S. Pietrowski

2008-10-01

Full Text Available In this paper quality monitoring of nodular cast iron and casting made of it is presented. A control system of initial liquid cast iron to spheroidization, after spheroidization and inoculation with using of TDA method was shown. An application of an ultrasonic method to assessment of the graphite form and the metal matrix microstructure of castings was investigated.

Nonoperative options for management of residual stones after cholecystostomy in high-risk patients

Science.gov (United States)

Reed, David M.; Daye, S. S.; Lincer, R. M.

1993-05-01

Cholecystostomy is frequently performed to obtain control of sepsis in high risk patients with acute cholecystitis. Retained stones in the gallbladder may cause future clinical problems. We present two patients with cholecystostomy tubes managed non-operatively. A review of other reported methods for stone extraction or destruction is also presented. Knowledge of safe and effective techniques for removal of these stones, using minimally invasive techniques is useful to the general surgeon.

Confiabilidade do uso de modelos digitais tridimensionais como exame auxiliar ao diagnóstico ortodôntico: um estudo piloto Reliability of three-dimensional digital casts as a diagnostic tool for orthodontic treatment planning: a pilot study

Directory of Open Access Journals (Sweden)

Dauro Douglas Oliveira

2007-02-01

initially generate controversy, and with digital orthodontic casts it has not been different. Some orthodontists may question the reliability of this new diagnostic tool since there is not enough literature to support the substitution from traditional stone casts to digital models. Therefore, the aim of the present study was to compare the reliability of digital orthodontic models and stone casts as a diagnostic aid. METHODS: three examiners measured the width of the permanent teeth, intercanine and intermolar distances, overbite and overjet of stone and the corresponding digital casts from six patients. A digital caliper was used for measuring the stone casts and the eModel software to evaluate the digital models. RESULTS AND CONCLUSIONS: the results of this study showed no statistically significant difference among any of the measurements tested, except by the width of the lower second right premolar (p<0.05. However, these differences were not considered clinically relevant. These findings show that digital orthodontic casts are as reliable as stone study models as a diagnostic tool for orthodontic treatment planning. The easy data storage, the lower risk of breakage during its handling and transportation, and also the shorter time needed to obtain the diagnostic information were considered additional advantages of this new technology.

Effects of disinfecting alginate impressions on the scratch hardness of stone models.

Science.gov (United States)

Hiraguchi, Hisako; Nakagawa, Hisami; Wakashima, Mitsuru; Miyanaga, Kohichi; Saigo, Masataka; Nishiyama, Minoru

2006-03-01

This study investigated the effects of disinfecting alginate impressions on the scratch depth of resultant stone models. Eleven brands of alginate impression material and two disinfectants, 1% sodium hypochlorite and 2% glutaraldehyde, were used. Impressions were immersed in disinfectant solutions or stored in sealed bags after spraying with disinfectants, and then poured with a type V dental stone. The scratch depth of the stone model obtained from disinfected impression was measured. The storage of alginate impressions after spraying with disinfectants did not increase the scratch depth of resultant stone models. However, the effect of immersion in disinfectants on scratch depth varied with the brand of the alginate impression material.

Reinforcement of Aluminum Castings with Dissimilar Metals

Energy Technology Data Exchange (ETDEWEB)

Han, Q

2004-01-07

The project ''Reinforcement of Aluminum Casting with Dissimilar Metal'' was a Cooperative Research and Development Agreements (CRADAs) between Oak Ridge National Laboratory (ORNL) and Cummins Inc. This project, technologies have been developed to reinforce aluminum castings with steel insert. Defect-free bond between the steel insert and the aluminum casting has been consistently obtained. The push-out experiment indicated that the bond strength is higher than that of the Al-Fin method. Two patents have been granted to the project team that is comprised of Cummins Inc. and ORNL. This report contains four sections: the coating of the steel pins, the cast-in method, microstructure characterization, and the bond strength. The section of the coating of the steel pins contains coating material selection, electro-plating technique for plating Cu and Ni on steel, and diffusion bonding of the coatings to the steel. The section of cast-in method deals with factors that affecting the quality of the metallurgical bond between the coated steel and the aluminum castings. The results of microstructure characteristics of the bonding are presented in the microstructure characterization section. A push-out experiment and the results obtained using this method is described in the section of bond strength/mechanical property.

A neural network - based algorithm for predicting stone - free status after ESWL therapy.

Science.gov (United States)

Seckiner, Ilker; Seckiner, Serap; Sen, Haluk; Bayrak, Omer; Dogan, Kazim; Erturhan, Sakip

2017-01-01

The prototype artificial neural network (ANN) model was developed using data from patients with renal stone, in order to predict stone-free status and to help in planning treatment with Extracorporeal Shock Wave Lithotripsy (ESWL) for kidney stones. Data were collected from the 203 patients including gender, single or multiple nature of the stone, location of the stone, infundibulopelvic angle primary or secondary nature of the stone, status of hydronephrosis, stone size after ESWL, age, size, skin to stone distance, stone density and creatinine, for eleven variables. Regression analysis and the ANN method were applied to predict treatment success using the same series of data. Subsequently, patients were divided into three groups by neural network software, in order to implement the ANN: training group (n=139), validation group (n=32), and the test group (n=32). ANN analysis demonstrated that the prediction accuracy of the stone-free rate was 99.25% in the training group, 85.48% in the validation group, and 88.70% in the test group. Successful results were obtained to predict the stone-free rate, with the help of the ANN model designed by using a series of data collected from real patients in whom ESWL was implemented to help in planning treatment for kidney stones. Copyright® by the International Brazilian Journal of Urology.

ASSESSING PATHOLOGIES ON VILLAMAYOR STONE (SALAMANCA, SPAIN BY TERRESTRIAL LASER SCANNER INTENSITY DATA

Directory of Open Access Journals (Sweden)

J. García-Talegón

2015-02-01

Full Text Available This paper deals with the assessing of pathologies in façades using a variety of intensity data provided by different terrestrial laser scanner. In particular, a complex building built in the Villamayor Stone that is to be candidate as a Global Heritage Stone Resource has been chosen as study case. The Villamayor Stone were quarrying for the construction and ornamentation of monuments in Salamanca, declared World Heritage City by UNESCO in 1988. The objective of this paper is to assess the pathologies of Villamayor Stone and compare the results obtained through the laser techniques with the classical techniques of mapped pathologies (i.e. visual inspection. For that intensity data coming from laser scanners will be used as non-destructive techniques applied to the façades and several retired plaques (after of building restoration of Villamayor Stone with pathologies (fissures, scales, loss of matter, humidity/biological colonization carried to the laboratory. Subsequently it will perform different comparisons between the accuracy reached with the different sensors and a high precision model setup on laboratory which performs as “ground truth”. In particular, the following objectives will be pursued: i accuracy assessment of the results obtained in in situ and laboratory; ii an automation or semi-automation of the detection of pathologies in Villamayor Stone; iii discriminate the different types of Villamayor Stone used in the façades in function of the radiometric response; iv establish a methodology for detection and assessing of pathologies based on laser scanner intensity data applied to monuments and modern buildings built in Villamayor Stone.

The twelve colourful stones

International Nuclear Information System (INIS)

Doria, R.M.

1984-01-01

The gauge symmetry is extended. It is associated differents matter and gauge fields to the same group. A group of gauge invariant Lagrangians is established. A gauge invariant mass term is introduced. A massive Yang Mills is obtained. A dynamics with twelve colourful stones is created based on the concepts of gauge and colour. Structures identified as quarks and leptons are generated. A discussion about colour meaning is presented. (Author) [pt

Extracorporeal shock wave lithotripsy for gallbladder stones - an experimental and clinical study -

International Nuclear Information System (INIS)

Kim, Kun Sang; Park, Sil Moo; Lee, Jung Hyo; Kim, Young Goo; Song, Kounn Sik; Lee, Kwan Seh; Lee, Jong Beum; Kim, Sang Joon; Chang, Sun Taik

1988-01-01

Although many alternative treatment technics have been proposed recently for gallstone to substitute cholecystectomy, the extracorporeal shock wave lithotripsy (ESWL) for gallbladder stones has rarely been tried. We have carried out a series of experiments to evaluate how effective the ESWL for gallbladder stones in and how safe this procedure is. At first, in vitro shock were application was carried out to 10 gallbladder stones which were obtained from human gallbladder. Secondly, gallbladder stones were implanted to canine gallbladder and treated with shock wave. Lastly, a total of 41 volunteers with confirmed gallbladder stones were treated with shock wave and combined oral administration of ursodeoxycholic acid. In the in vitro experiment, all of the 10 gallstones were fragmented with variable firing rates and duration. In animal experiment, the implanted stones were successfully fragmented and the organs included in the pathway of shock wave were proved to be intact histologically. In human study, complete disappearance of gallstones was noted in 78.6% of patients with single radiolucent gallbladder stones, smaller than 2.5cm in the longest diameter. Two patients underwent cholecystectomy after ESWL due to sudden colic attack. One patient had experienced an episode of mild transient obstructive jaundice. It may be concluded that the ESWL for gallbladder stones is an effective and safe method of treatment of gallbladder stones in the selected cases, for example, small radiolucent stones, and the further study is needed to establish improved technology of the ESWL for gallbladder stones.

Extracorporeal shock wave lithotripsy for gallbladder stones - an experimental and clinical study -

Energy Technology Data Exchange (ETDEWEB)

Kim, Kun Sang; Park, Sil Moo; Lee, Jung Hyo; Kim, Young Goo; Song, Kounn Sik; Lee, Kwan Seh; Lee, Jong Beum; Kim, Sang Joon; Chang, Sun Taik [Chung-Ang University College of Medicine, Seoul (Korea, Republic of)

1988-08-15

Although many alternative treatment technics have been proposed recently for gallstone to substitute cholecystectomy, the extracorporeal shock wave lithotripsy (ESWL) for gallbladder stones has rarely been tried. We have carried out a series of experiments to evaluate how effective the ESWL for gallbladder stones in and how safe this procedure is. At first, in vitro shock were application was carried out to 10 gallbladder stones which were obtained from human gallbladder. Secondly, gallbladder stones were implanted to canine gallbladder and treated with shock wave. Lastly, a total of 41 volunteers with confirmed gallbladder stones were treated with shock wave and combined oral administration of ursodeoxycholic acid. In the in vitro experiment, all of the 10 gallstones were fragmented with variable firing rates and duration. In animal experiment, the implanted stones were successfully fragmented and the organs included in the pathway of shock wave were proved to be intact histologically. In human study, complete disappearance of gallstones was noted in 78.6% of patients with single radiolucent gallbladder stones, smaller than 2.5cm in the longest diameter. Two patients underwent cholecystectomy after ESWL due to sudden colic attack. One patient had experienced an episode of mild transient obstructive jaundice. It may be concluded that the ESWL for gallbladder stones is an effective and safe method of treatment of gallbladder stones in the selected cases, for example, small radiolucent stones, and the further study is needed to establish improved technology of the ESWL for gallbladder stones.

Combined testing of castings having rough surface

International Nuclear Information System (INIS)

Polyakov, Yu.O.; Zav'yalkin, F.M.; Moskvin, V.N.

1988-01-01

Mathematical models of a flaw detector for complex testing of castings, containing radiometric and pneumatic converters, are developed and investigated. The efficiency of compensation of casting thickness fluctuation effect on the results of testing in combined information processing obtained by various methods is estimated

'Cutting for the stone': the ancient art of lithotomy.

Science.gov (United States)

Herr, Harry W

2008-05-01

Bladder stone was a common ailment plaguing mankind from antiquity to the 20th century. Largely forgotten today, lithotomy relieved the anguish of bladder stones and identified urology as a medical specialty nearly 2500 years ago. The historical literature pertaining to lithotomy was reviewed. Translated and original documents describing operative techniques and developments pertaining to the history of lithotomy were obtained through the internet and library sources. The ancient art of lithotomy was first recorded by the Greeks and evolved through five phases: the Celsian method, or 'lesser operation'; the Marian, or 'greater operation'; the lateral operation; suprapubic cystotomy, or 'high operation', and proctocystotomy. The practice of open lithotomy ceased to exist owing to better minimally invasive alternative methods and most notably by the virtual disappearance of bladder stones in modern man. The history of lithotomy is a fascinating story of how early surgeons forced by the culture and customs of the time dealt with common but devastating bladder stones. Out of their efforts, urology was born.

Introduction. Leave no stone unturned: Perspectives on ground stone artefact research

OpenAIRE

Danny Rosenberg; Yorke Rowan; Tatjana Gluhak

2016-01-01

Ground stone tools served in many physical and social contexts through millennia, reflecting a wide variety of functions. Although ground stone tool studies were neglected for much of early archaeology, the last few decades witnessed a notable international uptick in the way archaeologists confront this multifaceted topic. Today, with the advance of archaeology as a discipline, research into ground stone artefacts is moving into a new phase that integrates high resolution documentation with n...

Treatment of gallbladder stone with common bile duct stones in the laparoscopic era.

Science.gov (United States)

Zhang, Wei-jie; Xu, Gui-fang; Huang, Qin; Luo, Kun-lun; Dong, Zhi-tao; Li, Jie-ming; Wu, Guo-zhong; Guan, Wen-xian

2015-01-26

Laparoscopic common bile duct exploration (LCBDE) for stone can be carried out by either laparoscopic transcystic stone extraction (LTSE) or laparoscopic choledochotomy (LC). It remains unknown as to which approach is optimal for management of gallbladder stone with common bile duct stones (CBDS) in Chinese patients. From May 2000 to February 2009, we prospective treated 346 consecutive patients with gallbladder stones and CBDS with laparoscopic cholecystectomy and LCBDE. Intraoperative findings, postoperative complications, postoperative hospital stay and costs were analyzed. Because of LCBDE failure,16 cases (4.6%) required open surgery. Of 330 successful LCBDE-treated patients, 237 underwent LTSE and 93 required LC. No mortality occurred in either group. The bile duct stone clearance rate was similar in both groups. Patients in the LTSE group were significantly younger and had fewer complications with smaller, fewer stones, shorter operative time and postoperative hospital stays, and lower costs, compared to those in the LC group. Compared with patients with T-tube insertion, patients in the LC group with primary closure had shorter operative time, shorter postoperative hospital stay, and lower costs. In cases requiring LCBDE, LTSE should be the first choice, whereas LC may be restricted to large, multiple stones. LC with primary closure without external drainage of the CBDS is as effective and safe as the T-tube insertion approach.

Relationship between casting modulus and grain size in cast A356 aluminium alloys

International Nuclear Information System (INIS)

Niklas, A; Abaunza, U; Fernández-Calvo, A I; Lacaze, J

2012-01-01

Microstructure of Al-Si alloy castings depends most generally on melt preparation and on the cooling rate imposed by the thermal modulus of the component. In the case of Al-Si alloys, emphasis is put during melt preparation on refinement of pro-eutectic (Al) grains and on modification of the Al-Si eutectic. Thermal analysis has been used since long to check melt preparation before casting, i.e. by analysis of the cooling curve during solidification of a sample cast in an instrumented cup. The conclusions drawn from such analysis are however valid for the particular cooling conditions of the cups. It thus appeared of interest to investigate how these conclusions could extrapolate to predict microstructure in complicated cast parts showing local changes in the solidification conditions. For that purpose, thermal analysis cups and instrumented sand and die castings with different thermal moduli and thus cooling rates have been made, and the whole set of cooling curves thus recorded has been analysed. A statistical analysis of the characteristic features of the cooling curves related to grain refinement in sand and die castings allowed determining the most significant parameters and expressing the cube of grain size as a polynomial of these parameters. After introduction of a further parameter quantifying melt refining an excellent correlation, with a R 2 factor of 0.99 was obtained.

Everybody Must Get Stones

Directory of Open Access Journals (Sweden)

Timothy Darvill

2009-09-01

Full Text Available It is now widely recognised that monument building in the fourth and third millennia cal BC often involved transporting selected blocks of preferred stone many kilometres over difficult terrain. Some structures incorporated blocks from several different sources, brought together as an ensemble in much the same way perhaps that assemblages of flint and stone axes reflect both local and distant sources. This article explores alternative models accounting for the selection of stones, contrasting those that foreground symbolic attachments and imposed meanings with those that focus on the intrinsic qualities of particular types of stone and their source. The assemblage of different stone types that accumulated at Stonehenge, Wiltshire, over a period of more than a thousand years is used as a case study.

Interface Structure and Elements Diffusion of As-Cast and Annealed Ductile Iron/Stainless Steel Bimetal Castings

Directory of Open Access Journals (Sweden)

M. Ramadan

2018-04-01

Full Text Available Bimetal casting is considered to a promising technique for the production of high performance function materials. Heat treatment process for bimetal castings became an essential tool for improving interface structure and metallurgical diffusion bond. Molten iron alloy with carbon equivalent of 4.40 is poured into sand mold cavities containing solid 304 stainless steel strips insert. Specimens are heated to 7200C in an electrical heating furnace and holded at 720 0C for 60min and 180min. For as-cast specimens, a good coherent interface structure of ductile cast iron/304 stainless bimetal with four layers interfacial microstructure are obtained. Low temperature annealing at 720oC has a significat effect on the interface layers structure, where, three layers of interface structure are obtained after 180min annealing time because of the complete dissolving of thin layer of ferrite and multi carbides (Layer 2. Low temperature annealing shows a significant effect on the diffusion of C and otherwise shows slightly effect on the diffusion of Cr and Ni. Plearlite phase of Layer 3 is trsformed to spheroidal shape instead of lamallar shape in as-cast bimetals by low tempeature annealing at 720oC. The percent of the performed spheroidal cementit increases by increasing anneaaling time. Hardness of interface layers is changed by low temperauture annealing due to the significant carbon deffussion.

Study of the machining of uranium carbide rods obtained by continuous casting under electronic bombardment

International Nuclear Information System (INIS)

Rousset, P.; Accary, A.

1965-01-01

The authors consider the various methods of machining uranium mono-carbide and compare them critically in the case of their application to uranium carbide obtained by fusion under an electronic bombardment and continuous casting. This study leads them to propose two mechanical machining methods: cylindrical rectification and center-less rectification, preceded by a preliminary roughing out of a cylinder, the latter appearing more suitable. A study of the machining yields as a function of the diameter of the rough bars and of the diameter of the finished rods has shown that an optimum value of the rough bar diameter exists for each value of the finished rod diameter. It is found that the yield increases as the diameter itself increases, this yield rising from 45 per cent to around 70 per cent as the diameter of the rough bars increases from 25-26 mm to 37-38 mm. (authors) [fr

Textural characterization and chemistry of activated coal obtained starting from stone of African palm at different conditions of temperature and carbonization time

International Nuclear Information System (INIS)

Diaz, Claudia Marcela; Briceno, Nelson; Baquero, Maria Cristina; Giraldo, Liliana; Moreno, Juan Carlos

2002-01-01

Activated carbons are obtained starting from stone of African palm, by means of chemical activation with k 2 CO 3 and thermal activation with CO 2 . The initial material undergoes different conditions of carbonization temperature 600, 750 and 900 Celsius degrades and different times of carbonization 1.0; 1.5; 2.0 and 2.5 hours, with the objective of observing how these conditions affect the porosity of the material. It is observed a low development of the porosity in the carbons carbonized to 900 Celsius degrade and activated chemically. The acidity and basicity are determined for each one of the activated carbons obtained for titration with solutions 0.05 m of sodium hydroxide and of hydrochloric acid respectively. The samples activated chemically present bigger contents of acid groups, for the experimental conditions of work? Than the samples obtained by thermal activation for the activated carbons thermally activated, the values for acid and basic groups are low-between 0,20 and 0,72 meq g-l

Dimensional accuracy and surface property of titanium casting using gypsum-bonded alumina investment.

Science.gov (United States)

Yan, Min; Takahashi, Hidekazu; Nishimura, Fumio

2004-12-01

The aim of the present study was to evaluate the dimensional accuracy and surface property of titanium casting obtained using a gypsum-bonded alumina investment. The experimental gypsum-bonded alumina investment with 20 mass% gypsum content mixed with 2 mass% potassium sulfate was used for five cp titanium castings and three Cu-Zn alloy castings. The accuracy, surface roughness (Ra), and reaction layer thickness of these castings were investigated. The accuracy of the castings obtained from the experimental investment ranged from -0.04 to 0.23%, while surface roughness (Ra) ranged from 7.6 to 10.3microm. A reaction layer of about 150 microm thickness under the titanium casting surface was observed. These results suggested that the titanium casting obtained using the experimental investment was acceptable. Although the reaction layer was thin, surface roughness should be improved.

First experience of electron microscopic and bacteriological examination of the prostate gland stones

Directory of Open Access Journals (Sweden)

I. V. Vinogradov

2014-01-01

Full Text Available The work is based on a study of prostate stones obtained by transurethral resection of the prostate in 5 patients with benign prostatic hyperplasia in combination with chronic calculous prostatitis. Stones have been investigated by scanning electron microscopy and X-ray microstructural analysis, as well as a comparative study of bacteriological swabs from the surface of the stones after ultrasonic treatment of stone and without it. Pretreatment ultrasound prostate stones before sowing on nutrient medium swabs improves bacteriological diagnosis, which may be due to the dispersion of biofilms and exit vegetative forms of bacteria from it. This feature can serve as ultrasound theoretical justification for its use to improve the efficiency of diagnosis of various forms of prostatitis.

Ultrasonic propulsion of kidney stones.

Science.gov (United States)

May, Philip C; Bailey, Michael R; Harper, Jonathan D

2016-05-01

Ultrasonic propulsion is a novel technique that uses short bursts of focused ultrasonic pulses to reposition stones transcutaneously within the renal collecting system and ureter. The purpose of this review is to discuss the initial testing of effectiveness and safety, directions for refinement of technique and technology, and opinions on clinical application. Preclinical studies with a range of probes, interfaces, and outputs have demonstrated feasibility and consistent safety of ultrasonic propulsion with room for increased outputs and refinement toward specific applications. Ultrasonic propulsion was used painlessly and without adverse events to reposition stones in 14 of 15 human study participants without restrictions on patient size, stone size, or stone location. The initial feasibility study showed applicability in a range of clinically relevant situations, including facilitating passage of residual fragments following ureteroscopy or shock wave lithotripsy, moving a large stone at the ureteropelvic junction with relief of pain, and differentiating large stones from a collection of small fragments. Ultrasonic propulsion shows promise as an office-based system for transcutaneously repositioning kidney stones. Potential applications include facilitating expulsion of residual fragments following ureteroscopy or shock wave lithotripsy, repositioning stones prior to treatment, and repositioning obstructing ureteropelvic junction stones into the kidney to alleviate acute renal colic.

Colour Metallography of Cast Iron

Directory of Open Access Journals (Sweden)

Zhou Jiyang

2009-05-01

Full Text Available Cast iron, as a traditional metal material, has advantages of low total cost, good castability and machinability, good wear resistance and low notch sensitivity, and is still facing tough challenge in quality, property and variety of types etc. Experts and engineers studying and producing iron castings all around world extremely concern this serious challenge. Over more than 30 years, a great of research work has been carried out on how to further improve its property, expand its application and combine cast iron technology with some hi-techs (for example, computer technology. Nevertheless, cast iron is a multi-element and multi-phase alloy and has complex and variety of structures and still has great development potential in structure and property. For further studying and developing cast iron, theoretical research work is important promise, and the study on solidification process and control mechanism of graphite morphology is fundamental for improving property of cast iron and developing new type of cast iron.Metallography of cast iron normally includes two sections: liquid phase transformation and solid phase transformation. The book, Colour Metallography of Cast Iron , uses colour metallography technique to study solidification structures of cast irons: graphite, carbides, austenite and eutectics; and focuses on solidification processes. With progress of modern solidification theory, the control of material solidification process becomes important measure for improving traditionalmaterials and developing new materials. Solidification structure not only influences mechanical and physical properties of cast iron, but also affects its internal quality. The book uses a large amount of colour photos to describe the formation of solidification structures and their relations. Crystallization phenomena, which cannot be displayed with traditional metallography, are presented and more phase transformation information is obtained from these colour

Casting Technology.

Science.gov (United States)

Wright, Michael D.; And Others

1992-01-01

Three articles discuss (1) casting technology as it relates to industry, with comparisons of shell casting, shell molding, and die casting; (2) evaporative pattern casting for metals; and (3) high technological casting with silicone rubber. (JOW)

Modeling of TiAl Alloy Grating by Investment Casting

OpenAIRE

Yi Jia; Shulong Xiao; Jing Tian; Lijuan Xu; Yuyong Chen

2015-01-01

The investment casting of TiAl alloys has become the most promising cost-effective technique for manufacturing TiAl components. This study aimed to investigate a series of problems associated with the investment casting of TiAl alloys. The mold filling and solidification of this casting model were numerically simulated using ProCAST. Shrinkage porosity was quantitatively predicted by a built-in feeding criterion. The results obtained from the numerical simulations were compared with experimen...

Quality Assessment of Urinary Stone Analysis

DEFF Research Database (Denmark)

Siener, Roswitha; Buchholz, Noor; Daudon, Michel

2016-01-01

After stone removal, accurate analysis of urinary stone composition is the most crucial laboratory diagnostic procedure for the treatment and recurrence prevention in the stone-forming patient. The most common techniques for routine analysis of stones are infrared spectroscopy, X-ray diffraction......, fulfilled the quality requirements. According to the current standard, chemical analysis is considered to be insufficient for stone analysis, whereas infrared spectroscopy or X-ray diffraction is mandatory. However, the poor results of infrared spectroscopy highlight the importance of equipment, reference...... spectra and qualification of the staff for an accurate analysis of stone composition. Regular quality control is essential in carrying out routine stone analysis....

Significance of lower-pole pelvicaliceal anatomy on stone clearance after shockwave lithotripsy in nonobstructive isolated renal pelvic stones.

Science.gov (United States)

Sozen, Sinan; Kupeli, Bora; Acar, Cenk; Gurocak, Serhat; Karaoglan, Ustunol; Bozkirli, Ibrahim

2008-05-01

To investigate the probable effect of lower-pole pelvicaliceal anatomy on stone clearance after shockwave lithotripsy (SWL) in patients with nonobstructive renal pelvic stones. The clinical records of patients with isolated renal pelvic stones who underwent SWL between 1996 and 2005 were reviewed. After excluding patients with obstruction leading to dilatation, major anatomic abnormalities, noncalcium stones, metabolic abnormalities, history of recurrent stone disease, multiple stones, and previous renal surgery, 153 patients were enrolled in the study. Lower pole infundibulopelvic angle (IPA) and infundibular length and width were measured from intravenous urography. Patients were classified into three groups according to stone burden (group 1, renal pelvis, and both in 50 (32.6%), 29 (18.9%), and 8 (5.2%) patients, respectively. There was no statistically significant difference in pelvicaliceal anatomic features except narrower IPA (P=0.02) in group 1 patients with residual stones. The falling of stone fragments to the lower calix in spite of the ureter whether clinically significant or not after SWL of pelvic stones initially seems to be related to stone burden rather than lower caliceal anatomy. However, existence of a more narrow IPA in group 1 patients with residual fragments led us to believe that lower-pole IPA can play a role in stone clearance, especially for smaller stones, probably because of smaller residual fragment size or the more mobile nature of the primary stone.

FY 1998 annual report on the development of laser-aided, noncontacting, realtime, in-process dressing method using a grinding stone with ultrafine abrasive grains, and study on techniques for applying the method to grinding stone of superthin blades; 1998 nendo laser wo mochiita choteiryu toishi no hisesshoku real time inprocess dressing ho no kaihatsu oyobi gokuusuha toishi eno tekiyo gijutsu ni kansuru kenkyu chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A new noncontacting dressing method using a laser as a tool has been studied and developed, in order to develop environment-compatible, energy-saving type machining machines. In this study, a cup-shaped grinding stone is developed for grinding performance testing by micron-order diamond abrasive powder, used for producing a grinding stone of superthin blades, is mixed with a cast iron binder, molded and sintered. In the grinding performance test, zirconia as a work is ground at a constant pressure to the grinding stone working surface before and after the laser-aided dressing, to analyze grinding/removal efficiency and grinding resistance. The grinding stone working surface conditions are observed by a scanning electron microscope after the laser-aided dressing, to correlate the surface conditions with the grinding data. It is found that the laser-aided dressing method needs no lubricant, is clean, cutting grinding time when incorporated in the machining process, suitable for grinding stone of low stiffness and ultrathin blades by use of ultrafine abrasive grains, suffering no exfoliation of the diamond grains, and hence economical. (NEDO)

Use of the probability of stone formation (PSF) score to assess stone forming risk and treatment response in a cohort of Brazilian stone formers

OpenAIRE

Turney, Benjamin; Robertson, William; Wiseman, Oliver; Amaro, Carmen Regina P. R.; Leitão, Victor A.; Silva, Isabela Leme da; Amaro, João Luiz

2014-01-01

Introduction: The aim was to confirm that PSF (probability of stone formation) changed appropriately following medical therapy on recurrent stone formers.Materials and Methods: Data were collected on 26 Brazilian stone-formers. A baseline 24-hour urine collection was performed prior to treatment. Details of the medical treatment initiated for stone-disease were recorded. A PSF calculation was performed on the 24 hour urine sample using the 7 urinary parameters required: voided volume, oxalate...

Effect of Tamsulosin on Stone Passage for Ureteral Stones: A Systematic Review and Meta-analysis.

Science.gov (United States)

Wang, Ralph C; Smith-Bindman, Rebecca; Whitaker, Evans; Neilson, Jersey; Allen, Isabel Elaine; Stoller, Marshall L; Fahimi, Jahan

2017-03-01

Tamsulosin is recommended for patients receiving a diagnosis of a ureteral stone less than 10 mm who do not require immediate urologic intervention. Because of conflicting results from recent meta-analyses and large randomized controlled trials, the efficacy of tamsulosin is unclear. We perform a systematic review and meta-analysis to investigate the effect of tamsulosin on stone passage in patients receiving a diagnosis of ureteral stone. MEDLINE, EMBASE, and CENTRAL databases were searched without language restriction through November 2015 for studies assessing the efficacy of tamsulosin and using a double-blind, randomized, controlled trial design. Meta-analysis was conducted with a random-effects model and subgroup analyses were conducted to determine sources of heterogeneity. Eight randomized controlled trials (N=1,384) contained sufficient information for inclusion. The pooled risk of stone passage in the tamsulosin arm was 85% versus 66% in the placebo arm, but substantial heterogeneity existed across trials (I 2 =80.2%; Ptamsulosin (risk difference=22%; 95% confidence interval 12% to 33%; number needed to treat=5). The meta-analysis of the small stone subgroup (Tamsulosin significantly improves stone passage in patients with larger stones, whereas the effect of tamsulosin is diminished in those with smaller stones, who are likely to pass their stone regardless of treatment. Copyright © 2016 American College of Emergency Physicians. Published by Elsevier Inc. All rights reserved.

"Piedra Franca": the same name for many different natural stones.

Science.gov (United States)

Pereira, Dolores; Navarro, Rafael; Baltuille, Jose Manuel

2014-05-01

The Spanish name "Piedra Franca" refers to all the stones of sedimentary origin that have uniform coloration and easeof cutting/carving in order to obtain dimensional blocks for construction. The first references to this denomination occurred during medieval times, when builders had to choose the best materials to construct magnificent cathedrals. The largest volume of such natural stones were extracted from Caen, northern France, and historic records use the English term, "freestone", ie stone easy to cut, and to work by the masons dedicated to build cathedrals ("freemasons") in contrast to the "roughstone", hard stones worked by the hard hewers or "rough masons". The original French name referred to the limestones extracted at Caen, but over time, the original meaning expanded to include other natural stones with similar coloration and ease to carve. Notably this included many sandstones that were used in adjacent countries such as Spain. In the latter, although the most popular for its importance in architectural heritage is the Villamayor sandstone from Salamanca, other historically important natural stones are also known as "Piedra Franca" including the calcarenite from Santa Pudia (Granada), the limestone from Alava, the sandstone from Jaen and the sandstone from Cádiz. All of them were used in the construction of Spanish architectonic heritage and share similar exterior characteristics. In fact, several are known as golden stones. However when conservation and restoration of architectonic heritage is involved, the correct and original material should be used. The existence of national networks (e.g. CONSTRUROCK) and international task groups (e.g. IUGS Heritage Stone Task Group) can help to properly characterize, document, and differentiate between the varieties of "Piedra Franca" and they should be consulted by builders, architects and any other stone professsionals involved in such activities. An error in choosing the natural stone can result in

Utility of Flexible Ureterorenoscopy and Laser Lithotripsy in the Treatment of Multiple Intrarenal Stones

Directory of Open Access Journals (Sweden)

Hasan Yılmaz

2017-09-01

Full Text Available Objective: We aimed to determine the safety and efficacy of flexible ureterorenoscopy and Holmium laser lithotripsy in treating multiple intrarenal stones. Materials and Methods: We identified 32 consecutive patients with multiple intrarenal stones who underwent flexible ureterorenoscopy and/or laser lithotripsy performed by a single surgeon. Informed consent was obtained from all participants before treatment. Each patient was evaluated in terms of stone location, stone number, stone size, stone burden (cumulative stone length, body mass index, operative time, stone-free rate, and perioperative complications. Results: The median age of the patients was 38 years [interquartile range (IQR, 34.25-52.00]. The patients had a total of 75 intrarenal calculi. The average number of stones per patient was 2.50 (IQR, 2.0-3.0. The median total stone burden per patient was 23.0 mm (IQR, 19.0-28.0 mm. Twenty-one patients (65.5% had stone burdens >20 mm, and 11 (34.5% had burdens ≤20 mm. The overall final stone-free rate was 78.1%. The stone-free rates for patients with stone burdens ≤20 mm and >20 mm were 81.8% (9/11 and 76.2% (16/21, respectively (p=0.544. A perioperative complication (urinary leakage occurred in one patient. Postoperative complications were recorded in four (12.5% patients; a urinary tract infection in one, pain requiring parenteral medication in two, and hematuria in one. Conclusion: Flexible ureterorenoscopy combined with laser lithotripsy may be an effective treatment option for patients with multiple intrarenal stones; we noted only a few minor complications. The success rate was higher in patients with stone burdens ≤20 mm.

Diagnostic Value of Manual and Computerized Methods of Dental Casts Analysis

Directory of Open Access Journals (Sweden)

H. Rahimi

2009-06-01

Full Text Available Objective: The aim of this study was to evaluate the validity of computerized and manual methods of dental cast analysis.Materials and Methods: Twenty set-ups of upper and lower casts using artificial teeth corresponding to various malocclusions were created for a diagnostic in vitro study. Values of tooth size were calculated from the isolated artificial teeth out of the set-ups, results were considered as a gold standard for the tooth size. Arch width was calculated from the existing set-ups on the dentins.Impressions were taken of the casts with alginate and duplicated with dental stone. Models were measured with digital caliper manually. Then images were taken from the occlusal views of the casts by a digital camera. Measurements were done on digital images with the AutoCAD software.The results of the computerized and manual methods were compared with the gold standard.Intra class correlation coefficient of reliability was used to measure the accuracy ofthe methods and the Friedman technique used to evaluate the significance of differences.Results: Results indicated that all measurements were highly correlated, e.g. gold standard and manual (0.9613-0.9991, gold standard and computerized (0.7118-0.9883, manual and computerized (0.6734-0.9914. Statistically significant differences were present between these methods (P<0.05, but they proved not to be clinically significant.Conclusion: Manual measurement is still the most accurate method when compared to the computerized measurements and the results of measurement by computer should be interpreted with caution.

Solidification and casting

CERN Document Server

Cantor, Brian

2002-01-01

INDUSTRIAL PERSPECTIVEDirect chillcasting of aluminium alloysContinuous casting of aluminium alloysContinuous casting of steelsCastings in the automotive industryCast aluminium-silicon piston alloysMODELLING AND SIMULATIONModelling direct chill castingMold filling simulation of die castingThe ten casting rulesGrain selection in single crystal superalloy castingsDefects in aluminium shape castingPattern formation during solidificationPeritectic solidificationSTRUCTURE AND DEFECTSHetergeneous nucleation in aluminium alloysCo

In vitro CT evaluation of intrahepatic stones: correlation with chemical composition

International Nuclear Information System (INIS)

Kim, Young Jun; Han, Joon Koo; Jeong, Jun Yong; Lee, Kyoung Ho; Kim, Se Hyung; Kim, Young Il; Lee, Jeong Min; Choi, Byung Ihn; Park, Youn-Chan; Kim, Sun-Whe

2005-01-01

Objective: To describe in vitro CT features of intrahepatic stones and to correlate CT attenuation with chemical composition. Materials and methods: Of the patients who underwent choledochoscopic intrahepatic stone removal between 1998 and 2001, 54 patients with stones larger than 3 mm were enrolled in this study. In each case, a chemical compositional analysis was performed to determine calcium, cholesterol, total bilirubin, and inorganic phosphorus compositions. The three largest stones obtained from each patient were imaged by CT. CT attenuation numbers were measured in the center images of each stone by drawing free-hand region of interest (ROI). The measured CT attenuation numbers were correlated with their chemical composition. Also, CT attenuation numbers of stones were compared with that of the liver on non-contrast CT (50-70 HU). Results: Stone size ranged from 3.1 to 10.5 mm (mean ± S.D.: 6.0 ± 1.4). The CT attenuation numbers (HU) of stones ranged from 36.4 to 410.19 (mean ± S.D.: 94.6 ± 49.9). CT numbers of stones were below 70 HU in 11 patients (20.4%), and below 90 HU in 33 patients (59.3%). The chemical analysis data of the stones were as follows: calcium (0.5-6.5 wt.%; mean ± S.D., 2.6 ± 1.4), total bilirubin (0.45-24.4 wt.%; 13.1 ± 6.2), cholesterol (5.4-73.9 wt.%; 29.3 ± 17.4), phosphorus (0.1-1.2 wt.%; 0.6 ± 0.3), and non-soluble residue (17.6-85.4 wt.%; 57.0 ± 22.6). There was a weak but significant correlation between calcium composition and CT attenuation (r = 0.38, P 0.01; total bilirubin, r = 0.05, P > 0.01; phosphorus, r = 0.01, P > 0.01). Conclusion: On non-contrast CT, intrahepatic stones would not be hyperattenuating with respect to liver parenchyma in about one fifth of patients. The CT attenuation of stones correlates with calcium and does not correlate with any other chemical composition

Simplified methods for the evaluation of the risk of forming renal stones and the follow-up of stone-forming propensity during the preventive treatment of stone-formation.

Science.gov (United States)

Grases, Fèlix; Costa-Bauzá, Antonia

2016-02-01

Renal lithiasis is a complex multifactorial disease in which recurrence is common. Thus, simple and reliable procedures are needed to evaluate patients with previous kidney stones to determine the risk of recurrence. In this paper we review simple biochemical procedures that can be used to determine the risk for renal stone formation when the stone is available or unavailable for analysis. Our present knowledge of renal lithiasis indicates that renal stones form due to several well-defined factors. Analysis of the renal stone itself can provide important information about clinical factors that require further investigation. When the stone is unavailable, it is necessary to perform a general evaluation of main urinary risk factors associated to renal stone formation, but this study should be complemented considering information related to direct familial antecedents, recidivant degree, radiological images, medical history, and life style habits. Finally, tools for patient follow-up of stone-forming propensity during the preventive treatment are discussed .

Comparison of marginal accuracy of castings fabricated by conventional casting technique and accelerated casting technique: an in vitro study.

Science.gov (United States)

Reddy, S Srikanth; Revathi, Kakkirala; Reddy, S Kranthikumar

2013-01-01

Conventional casting technique is time consuming when compared to accelerated casting technique. In this study, marginal accuracy of castings fabricated using accelerated and conventional casting technique was compared. 20 wax patterns were fabricated and the marginal discrepancy between the die and patterns were measured using Optical stereomicroscope. Ten wax patterns were used for Conventional casting and the rest for Accelerated casting. A Nickel-Chromium alloy was used for the casting. The castings were measured for marginal discrepancies and compared. Castings fabricated using Conventional casting technique showed less vertical marginal discrepancy than the castings fabricated by Accelerated casting technique. The values were statistically highly significant. Conventional casting technique produced better marginal accuracy when compared to Accelerated casting. The vertical marginal discrepancy produced by the Accelerated casting technique was well within the maximum clinical tolerance limits. Accelerated casting technique can be used to save lab time to fabricate clinical crowns with acceptable vertical marginal discrepancy.

A stone mould from Klinovac

Directory of Open Access Journals (Sweden)

Bulatović Aleksandar

2002-01-01

Full Text Available A two-piece stone mould that reached the National Museum at Vranje in 1966 had been recovered from a depth of about one meter at the site known as Tri Kruške (Three Pear-trees, the village of Klinovac. The site is situated on a river terrace on the right bank of the Krševica River some 15 kilometers south of Vranje. The mould was carved out of metamorphic rock from the class of schist, more exactly, of greenschist (with chlorite and mica as its constituent minerals that is widespread in the area, which geologically belongs to the upper (Vlasina complex of the Serbian-Macedonian mass. The mould was intended for casting four kinds of bronze weapons: three chisels and a winged axe. More sensitive as dating evidence, the winged axe (Ärmchenbeil may be broadly dated to the last three centuries of the second millennium BC. The type is geographically related with the Aegean, while its northernmost findspot so far is Pobit Kamak in northern Bulgaria. The chisels cast in this mould do not have direct analogies, although many hoards of similar tools have been registered in Croatia, Romania and Central Europe. Apparently the mould was made by a local workshop and from the locally available raw material. The possible activity of local workshops in the above mentioned period has already been presumed by scholars, and the Klinovac mould constitutes yet another corroboration of the hypothesis. Nevertheless its Aegean origin should not be ruled out completely, because cultural contacts between the Late Bronze Age population inhabiting the region and their southern neighbours seem quite certain, as evidenced by Mycenaean pottery discovered on the site of Resulja at Lučani near Bujanovac.

Compositions of stone and stone surface materials of historical monuments from Vidzeme and Zemgale

International Nuclear Information System (INIS)

Actins, A.; Spricis, A.; Zekunde, A.; Nemerova, A.

2004-01-01

By means of x-ray analysis composition of stone and stone surface materials of historical monuments from Vidzeme and Zemgale was investigated. Corrosion products of tuffa materials were identified on surfaces of some investigated monuments. Similarity of composition of products of stone corrosion for monuments from Latvia and Poland was recognised. Content of heavy metals at stone materials of historical monuments and at the surface layers of these monuments was investigated by means of atomic absorption and potentiometric stripping methods. Reasons of formation of compounds and pollution of investigated samples were discussed. (full text)

Melting and casting of FeAl-based cast alloy

Energy Technology Data Exchange (ETDEWEB)

Sikka, V.K. [Oak Ridge National Lab., TN (United States); Wilkening, D. [Columbia Falls Aluminum Co., Columbia Falls, MT (United States); Liebetrau, J.; Mackey, B. [AFFCO, L.L.C., Anaconda, MT (United States)

1998-11-01

The FeAl-based intermetallic alloys are of great interest because of their low density, low raw material cost, and excellent resistance to high-temperature oxidation, sulfidation, carburization, and molten salts. The applications based on these unique properties of FeAl require methods to melt and cast these alloys into complex-shaped castings and centrifugal cast tubes. This paper addresses the melting-related issues and the effect of chemistry on the microstructure and hardness of castings. It is concluded that the use of the Exo-Melt{trademark} process for melting and the proper selection of the aluminum melt stock can result in porosity-free castings. The FeAl alloys can be melted and cast from the virgin and revert stock. A large variation in carbon content of the alloys is possible before the precipitation of graphite flakes occurs. Titanium is a very potent addition to refine the grain size of castings. A range of complex sand castings and two different sizes of centrifugal cast tubes of the alloy have already been cast.

Surface hardening of two cast irons by friction stir processing

International Nuclear Information System (INIS)

Fujii, Hidetoshi; Kikuchi, Toshifumi; Nogi, Kiyoshi; Yamaguchi, Yasufumi; Kiguchi, Shoji

2009-01-01

The Friction Stir Processing (FSP) was applied to the surface hardening of cast irons. Flake graphite cast iron (FC300) and nodular graphite cast iron (FCD700) were used to investigate the validity of this method. The matrices of the FC300 and FC700 cast irons are pearlite. The rotary tool is a 25mm diameter cylindrical tool, and the travelling speed was varied between 50 and 150mm/min in order to control the heat input at the constant rotation speed of 900rpm. As a result, it has been clarified that a Vickers hardness of about 700HV is obtained for both cast irons. It is considered that a very fine martensite structure is formed because the FSP generates the heat very locally, and a very high cooling rate is constantly obtained. When a tool without an umbo (probe) is used, the domain in which graphite is crushed and striated is minimized. This leads to obtaining a much harder sample. The hardness change depends on the size of the martensite, which can be controlled by the process conditions, such as the tool traveling speed and the load. Based on these results, it was clarified that the FSP has many advantages for cast irons, such as a higher hardness and lower distortion. As a result, no post surface heat treatment and no post machining are required to obtain the required hardness, while these processes are generally required when using the traditional methods.

Histopathology Predicts the Mechanism of Stone Formation

Science.gov (United States)

Evan, Andrew P.

2007-04-01

About 5% of American women and 12% of men will develop a kidney stone at some time in their life and these numbers appear to be on the rise. Despite years of scientific research into the mechanisms of stone formation and growth, limited advances have been made until recently. Randall's original observations and thoughts on the mechanisms for kidney stone formation have been validated for idiopathic calcium oxalate stone formers (ICSF) but not for most other stone forming groups. Our current studies on selected groups of human stone formers using intraoperative papillary biopsies has shown overwhelming evidence for the presence of Randall's plaque in ICSF and that stone formation and growth are exclusively linked to its availability to urinary ions and proteins. Intense investigation of the plaque-stone junction is needed if we are to understand the factors leading to the overgrowth process on exposed regions of plaque. Such information should allow the development of treatment strategies to block stone formation in ICSF patients. Patients who form brushite stones, or who form apatite stones because of distal renal tubular acidosis (dRTA), or patients with calcium oxalate stones due to obesity bypass procedures, or patients with cystinuria, get plugged inner medullary collecting ducts (IMCD) which leads to total destruction of the lining cells and focal sites of interstitial fibrosis. These stone formers have plaque but at levels equal to or below non-stone formers, which would suggest that they form stones by a different mechanism than do ICSF patients.

Thermodynamic stability of austenitic Ni-Mn-Cu cast iron

Directory of Open Access Journals (Sweden)

A. Janus

2014-07-01

Full Text Available The performed research was aimed at determining thermodynamic stability of structures of Ni-Mn-Cu cast iron castings. Examined were 35 alloys. The castings were tempered at 900 °C for 2 hours. Two cooling speeds were used: furnace-cooling and water-cooling. In the alloys with the nickel equivalent value less than 20,0 %, partial transition of austenite to martensite took place. The austenite decomposition ratio and the related growth of hardness was higher for smaller nickel equivalent value and was clearly larger in annealed castings than in hardened ones. Obtaining thermodynamically stable structure of castings requires larger than 20,0 % value of the nickel equivalent.

Influence of Modification and Casting Technology on Structure of IN-713C Superalloy Castings

Directory of Open Access Journals (Sweden)

Binczyk F.

2016-09-01

Full Text Available The paper presents the results concerning impact of modification (volume and surface techniques, pouring temperature and mould temperature on stereological parameters of macrostructure in IN713C castings made using post-production scrap. The ability to adjust the grain size is one of the main issues in the manufacturing of different nickel superalloy castings used in aircraft engines. By increasing the grain size one can increase the mechanical properties, like diffusion creep resistance, in higher temperatures. The fine grained castings. on the other hand, have higher mechanical properties in lower temperatures and higher resistance to thermal fatigue. The test moulds used in this study, supplied by Pratt and Whitney Rzeszow, are ordinarily used to cast the samples for tensile stress testing. Volume modification was carried out using the patented filter containing cobalt aluminate. The macrostructure was described using the number of grains per mm2, mean grain surface area and shape index. Obtained results show strong relationship between the modification technique, pouring temperature and grain size. There was no significant impact of mould temperature on macrostructure.

Microstructural Evolution in Intensively Melt Sheared Direct Chill Cast Al-Alloys

Science.gov (United States)

Jones, S.; Rao, A. K. Prasada; Patel, J. B.; Scamans, G. M.; Fan, Z.

The work presented here introduces the novel melt conditioned direct chill casting (MC-DC) technology, where intensive melt shearing is applied to the conventional direct-chill casting process. MC-DC casting can successfully produce high quality Al-alloy billets. The results obtained from 80 mm diameter billets cast at speed of 200 mm/min show that MC-DC casting of Al-alloys, substantially refines the microstructure and reduces macro-segregation. In this paper, we present the preliminary results and discuss microstructural evolution during MC-DC casting of Al-alloys.

Obesometric factors associated with increased skin-to-stone distances in renal stone patients.

Science.gov (United States)

Allard, Christopher B; Shuster, Anatoly; Pinthus, Jehonathan H; Farrokhyar, Forough; Raees, A; Patlas, Michael; Matsumoto, Edward D; Whelan, J Paul

2012-12-01

Obese patients are at increased risk for renal stones as well as treatment failures due to increased skin-to-stone distances (SSD) and harder stone compositions. We investigated the relationships between obesometric parameters (body mass index [BMI], body fat distribution and obesity-related hormone levels) with SSD and stone hardness. We prospectively enrolled patients undergoing stone interventions at our institution. Computed tomography (CT) scans were analyzed; adipose tissue was identified according to Hounsfield units (HU) and separated into subcutaneous (SAT) and visceral (VAT) components. The pixels were averaged at three levels to calculate fat distribution: %VAT = (VAT)/(VAT + SAT). SSD was measured and HU were used as a surrogate for stone hardness. Obesity-related hormones leptin and adiponectin were measured by ELISA. Seventy-nine patients were prospectively enrolled. Mean BMI and %VAT were 30.02 kg/m2 and 40.13 kg/m2. Mean leptin and adiponectin levels were 17.5 ng/mL and 7.67 mcg/mL indicating high risk for metabolic consequences of obesity. Females had greater proportions of subcutaneous fat than males (%VAT 28.4 versus 46.94, p r = 0.454, p = 0.008). Obese patients with %VAT > 40 versus stone compositions as measured by HU than non-diabetics (982.86 versus 648.86, p = 0.001). Obesometric parameters such as BMI, body fat distribution, and the presence of diabetes mellitus are important considerations in the management of renal stone disease. A large proportion of subcutaneous fat, which can be estimated by physical examination, predicts SSD among obese patients and may aid treatment decisions in patients, particularly those without pre-treatment CT scans. Further studies are needed to refine the role of obesometrics in personalizing treatment decisions.

Dual-source dual-energy CT for the differentiation of urinary stone composition: preliminary study

International Nuclear Information System (INIS)

Yang Qifang; Zhang Wanshi; Meng Limin; Shi Huiping; Wang Dong; Bi Yongmin; Li Xiangsheng; Fang Hong; Guo Heqing; Yan Jingmin

2011-01-01

Objective: To evaluate dual-source dual-energy CT (DSCT) for the differentiation of' urinary stone composition in vitro. Methods: Ninety-seven urinary stones were obtained by endoscopic lithotripsy and scanned using dual-source dual-energy CT. The stones were divided into six groups according to infrared spectroscopy stone analysis: uric acid (UA) stones (n=10), cystine stones (n=5), struvite stones (n=6), calcium oxalate (CaOx) stones (n=22), mixed UA stones (n=7) and mixed calcium stones (n=47). Hounsfield units (HU) of each stone were recorded for the 80 kV and the 140 kV datasets by hand-drawing method. HU difference, HU ratio and dual energy index (DEI) were calculated and compared among the stone groups with one-way ANOVA. Using dual energy software to determine the composition of all stones, results were compared to infrared spectroscopy analysis. Results: There were statistical differences in HU difference [(-17±13), (229±34), (309±45), (512±97), (201±64) and (530±71) HU respectively], in HU ratio (0.96±0.03, 1.34±0.04, 1.41±0.03, 1.47±0.03, 1.30±0.07, and 1.49±0.03 respectively), and DEI (-0.006±0.004, 0.064±0.007, 0.080± 0.007, 0.108±0.011, 0.055±0.014 and 0.112±0.008 respectively) among different stone groups (F= 124.894, 407.028, 322.864 respectively, P<0.01). There were statistical differences in HU difference, HU ratio and DEI between UA stones and the other groups (P<0.01). There were statistical differences in HU difference, HU ratio and DEI between CaOx or mixed calcium stones and the other four groups (P< 0.01). There was statistical difference in HU ratio between cystine and struvite stones (P<0.01). There were statistical differences in HU difference, HU ratio and DEI between struvite and mixed UA stones (P< 0.05). Dual energy software correctly characterized 10 UA stones, 4 cystine stones, 22 CaOx stones and 6 mixed UA stones. Two struvite stones were considered to contain cystine. One cystine stone, 1 mixed UA stone, 4

Supplemental Immobilization Cast Stone Technology Development and Waste Form Qualification Testing Plan

Energy Technology Data Exchange (ETDEWEB)

Westsik, Joseph H. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Serne, R. Jeffrey [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Pierce, Eric M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Cozzi, Alex [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Chung, Chul-Woo [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Swanberg, David J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2013-05-31

The Hanford Tank Waste Treatment and Immobilization Plant (WTP) is being constructed to treat the 56 million gallons of radioactive waste stored in 177 underground tanks at the Hanford Site. The WTP includes a pretreatment facility to separate the wastes into high-level waste (HLW) and low-activity waste (LAW) fractions for vitrification and disposal. The LAW will be converted to glass for final disposal at the Integrated Disposal Facility (IDF). The pretreatment facility will have the capacity to separate all of the tank wastes into the HLW and LAW fractions, and the HLW Vitrification Facility will have the capacity to vitrify all of the HLW. However, a second immobilization facility will be needed for the expected volume of LAW requiring immobilization. A number of alternatives, including Cast Stone—a cementitious waste form—are being considered to provide the additional LAW immobilization capacity.

Can stone density on plain radiography predict the outcome of extracorporeal shockwave lithotripsy for ureteral stones?

Science.gov (United States)

Lim, Ki Hong; Jung, Jin-Hee; Kwon, Jae Hyun; Lee, Yong Seok; Bae, Jungbum; Cho, Min Chul; Lee, Kwang Soo

2015-01-01

Purpose The objective was to determine whether stone density on plain radiography (kidney-ureter-bladder, KUB) could predict the outcome of extracorporeal shockwave lithotripsy (ESWL) for ureteral stones. Materials and Methods A total of 223 patients treated by ESWL for radio-opaque ureteral stones of 5 to 20 mm were included in this retrospective study. All patients underwent routine blood and urine analyses, plain radiography (KUB), and noncontrast computed tomography (NCCT) before ESWL. Demographic, stone, and radiological characteristics on KUB and NCCT were analyzed. The patients were categorized into two groups: lower-density (LD) group (radiodensity less than or equal to that of the 12th rib, n=163) and higher-density (HD) group (radiodensity greater than that of the 12th rib, n=60). Stone-free status was assessed by KUB every week after ESWL. A successful outcome was defined as stone free within 1 month after ESWL. Results Mean stone size in the LD group was significantly smaller than that in the HD group (7.5±1.4 mm compared with 9.9±2.9 mm, p=0.002). The overall success rates in the LD and HD groups were 82.1% and 60.0%, respectively (p=0.007). The mean duration of stone-free status and average number of SWL sessions required for success in the two groups were 21.7 compared with 39.2 days and 1.8 compared with 2.3, respectively (pESWL since colic and radiodensity of the stone on KUB were independent predictors of successful ESWL. Conclusions Our data suggest that larger stone size, longer time to ESWL, and ureteral stones with a radiodensity greater than that of the 12th rib may be at a relatively higher risk of ESWL failure 1 month after the procedure. PMID:25598937

Trends in urological stone disease.

Science.gov (United States)

Turney, Benjamin W; Reynard, John M; Noble, Jeremy G; Keoghane, Stephen R

2012-04-01

To summarize the changes in prevalence and treatment of upper urinary tract stone disease in the UK over the last 10 years. Data from the Hospital Episode Statistics (HES) website (http://www.hesonline.nhs.uk) were extracted, summarized and presented. The number of upper urinary tract stone hospital episodes increased by 63% to 83,050 in the 10-year period. The use of shock wave lithotripsy (SWL) for treating all upper tract stones increased from 14,491 cases in 2000-2001 to 22,402 cases in 2010 (a 55% increase) with a 69% increase in lithotripsy for renal stones. There was a 127% increase in the number of ureteroscopic stone treatments from 6,283 to 14,242 cases over the 10-year period with a 49% increase from 2007/2008 to 2009/2010. There was a decline in open surgery for upper tract stones from 278 cases in 2000/2001 to 47 cases in 2009/2010 (an 83% reduction). Treatment for stone disease has increased substantially in comparison with other urological activity. In 2009/2010, SWL was performed almost as frequently as transurethral resection of the prostate or transurethral resection of bladder tumour, ureteroscopy for stones was performed more frequently than nephrectomy, radical prostatectomy and cystectomy combined, and percutaneous nephrolithotomy was performed more frequently than cystectomy. The present study highlights the increase in prevalence and treatment of stone disease in the UK over the last 10 years. If this trend continues it has important implications for workforce planning, training, service delivery and research in the field of urolithiasis. © 2011 THE AUTHORS. BJU INTERNATIONAL © 2011 BJU INTERNATIONAL.

Effect of palm oil fuel ash on compressive strength of palm oil boiler stone lightweight aggregate concrete

Science.gov (United States)

Muthusamy, K.; Zamri, N. A.; Kusbiantoro, A.; Lim, N. H. A. S.; Ariffin, M. A. Mohd

2018-04-01

Both palm oil fuel ash (POFA) and palm oil boiler stone (POBS) are by-products which has been continuously generated by local palm oil mill in large amount. Both by products is usually disposed as profitless waste and considered as nuisance to environment. The present research investigates the workability and compressive strength performance of lightweight aggregate concrete (LWAC) made of palm oil boiler stone (POBS) known as palm oil boiler stone lightweight aggregate concrete (POBS LWAC) containing various content of palm oil fuel ash. The control specimen that is POBS LWAC of grade 60 were produced using 100% OPC. Then, another 4 mixes were prepared by varying the POFA percentage from 10%, 20%, 30% and 40% by weight of cement. Fresh mixes were subjected to slump test to determine its workability before casted in form of cubes. Then, all specimens were subjected to water curing up to 28 days and then tested for its compressive strength. It was found out that utilizing of optimum amount of POFA in POBS LWAC would improve the workability and compressive strength of the concrete. However, inclusion of POFA more than optimum amount is not recommended as it will increase the water demand leading to lower workability and strength reduction.

Bacterial bio-mediated calcite precipitation for monumental stones conservation: methods of evaluation.

Science.gov (United States)

Tiano, P; Biagiotti, L; Mastromei, G

1999-05-01

The weathering of monumental stones is a complex process inserted in the more general 'matter transformation cycle' operated by physical, chemical and biological factors. The consequence of these combined actions is a loss of cohesion with dwindling and scaling of stone material and the induction of a progressive mineral matrix dissolution. In the case of calcareous stones, calcite leaching increases the material porosity and decreases its mechanical features with a general weakening of the superficial structural strength. Attempts to stop, or at least to slow down, deterioration of monumental stones has been made by conservative treatments with both inorganic or organic products. More recent studies show a new approach to hinder these phenomena by inducing a bio-mediated precipitation of calcite directly inside the stone porosity. This can be achieved either through the application of organic matrix macromolecules extracted from sea shells or of living bacteria. The effectiveness of the treatment using calcinogenic bacteria has been evaluated with laboratory tests specifically developed to evaluate the parameters such as : porosity, superficial strength and chromatic changes, influenced by the treatment itself. The results obtained seem to indicate that this type of treatment might not be suitable for monumental stone conservation.

Fasting and Urinary Stones

Directory of Open Access Journals (Sweden)

Ali Shamsa

2013-11-01

Full Text Available Introduction: Fasting is considered as one of the most important practices of Islam, and according to Prophet Mohammad, fasting is obligatory upon Muslims. The aim of this study is to evaluate the effects of fasting on urinary stones. Materials and Methods: Very few studies have been carried out on urinary stones and the effect of Ramadan fasting. The sources of the present study are Medline and articles presented by local and Muslim researchers. Meanwhile, since we are acquainted with three well-known researchers in the field of urology, we contacted them via email and asked for their professional opinions. Results: The results of studies about the relationship of urinary stones and their incidence in Ramadan are not alike, and are even sometimes contradictory. Some believe that increased incidence of urinary stones in Ramadan is related not to fasting, but to the rise of weather temperature in hot months, and an increase in humidity. Conclusion: Numerous biological and behavioral changes occur in people who fast in Ramadan and some researchers believe that urinary stone increases during this month.

The "green stones" of Valtellina and Valchiavenna (central Alps, northern Italy)

Science.gov (United States)

Cavallo, Alessandro

2015-04-01

folded, and are processed in two main commercial varieties: schistose ("serpentinoscisto") and massive ("serpentino da taglio"). In Valmalenco, the extraction and processing of schistose serpentinites for the production of slabs ("piode", splitted by hand with hammer and chisel), used in roofing and flooring, dates back at least to the XIV century. From the traditional underground extraction, the quarrying activities moved to the modern open-cast extraction in the seventies. The renowned quality of the secular serpentinite roof coverings is related to the excellent physical and mechanical properties, especially the flexural strength (average values around 90-100 MPa), very low porosity and the thaw/freezing resistance. The "massive" serpentinite achieved a special place in the national and international market of ornamental stones: the several extracted varieties (Serpentino Classico, Verde Vittoria, Verde Perlato, Verde Mare, Verde Principe, Verde Torre S. Maria), in addition to the excellent technical properties (flexural strength and thermal properties) that promote specific uses, make these stones much appreciated worldwide (e.g. Bundestag in Berlin, Germany). As part of the "green stones" of Valmalenco, two currently abandoned ophicalcite quarries have been active in the recent past. The extraction and processing of soapstone ("pietra ollare" or "pietra laugera", a talc and/or chlorite rich ultramafic/mafic rock) in Valmalenco and Valchiavenna probably dates back to the Iron Age; in Valchiavenna it is documented with certainty since Roman times and the Middle Ages. The extraction and processing of soapstone peaked around the middle of the XVIII century, with a dozen quarries and about 300 workers involved, between Chiavenna and Piuro. A limited production of soapstone is still active in the municipalities of Piuro (talc-olivine-tremolite fels) and Chiesa in Valmalenco (chlorite schist), where in addition to the traditional cooking pots ("Lavecc"), there is a growing

The economics of stone disease.

Science.gov (United States)

Canvasser, Noah E; Alken, Peter; Lipkin, Michael; Nakada, Stephen Y; Sodha, Hiren S; Tepeler, Abdulkadir; Lotan, Yair

2017-09-01

The rising prevalence of kidney stone disease is associated with significant costs to healthcare systems worldwide. This is in part due to direct procedural and medical management costs, as well as indirect costs to health systems, patients, and families. A number of manuscripts evaulating the economics of stone disease have been published since the 2008s International Consultation on Stone Disease. These highlight costs associated with stone disease, including acute management, surgical management, and medical management. This work hopes to highlight optimization in care by reducing inefficient treatments and maximizing cost-efficient preventative strategies.

Regional differences in constituents of gall stones.

Science.gov (United States)

Ashok, M; Nageshwar Reddy, D; Jayanthi, V; Kalkura, S N; Vijayan, V; Gokulakrishnan, S; Nair, K G M

2005-01-01

The pathogenesis of pigment and mixed gall stone formation remains elusive. The elemental constituents of gall stones from southern states of Tamil Nadu, Kerala and Karnataka have been characterized. Our aim was to determine the elemental concentration of representative samples of pigment, mixed and cholesterol gall stones from Andhra Pradesh using proton-induced X-ray emission (PIXE) using a 3 MV horizontal pelletron accelerator. Pigment gall stones had significantly high concentrations of copper, iron and lead; chromium was absent. Except for iron all these elements were significantly low in cholesterol gall stones and intermediate levels were seen in mixed gall stones. Highest concentrations of chromium was seen in cholesterol and titanium in mixed gall stones respectively; latter similar to other southern states. Arsenic was distinctly absent in cholesterol and mixed gall stones. The study has identified differences in elemental components of the gall stones from Andhra Pradesh.

The bioreceptivity of building stone

Science.gov (United States)

Mauko Pranjić, Alenka; Mulec, Janez; Muck, Tadeja; Hladnik, Aleš; Mladenovič, Ana

2015-04-01

Bioreceptivity is an intrinsic property of stone, and is defined as the ability of a material to be colonized by living organisms. The fouling and staining of building stone material due to the activity of microorganisms presents a serious problem in modern as well as historical buildings, not only due to the aesthetic impact but also due to the deterioration of the material. Biological colonisation on stone materials is influenced by a number of factors, e.g. the intrinsic properties of the stone (porosity, roughness, permeability, mineral composition), environmental parameters (e.g. solar radiation, temperature, water regime, climate, etc.), and specific microclimatic parameters (e.g. orientation, exposure to shadow, permanent capillary humidity, etc.). In order to assess the bioreceptivity of building stones, use is often made of artificial colonisation experiments compromising the inoculation of stones with a single species or a few isolated strains under laboratory conditions. In the present work the authors present the development of a method for the determination of bioreceptivity, as well as a study of the bioreceptivity of selected natural stone versus the latter's intrinsic properties. Field examples of biodeterioration are also presented. The study was supported by the Slovenian Research Agency (L1-5453).

Throwing behavior and mass distribution of stone selection in tufted capuchin monkeys (Cebus apella).

Science.gov (United States)

Cleveland, A; Rocca, A R; Wendt, E L; Westergaard, G C

2003-12-01

Cannell [Journal of Archaeological Science 29:335-339, 2002] argued that sex-based differences among humans in terms of the mass of chosen throwing stones could be used to infer body mass and patterns of sexual dimorphism in early hominids from Olduvai and Koobi Fora by examining the mass distributions of unaltered stone tools at those sites. We examined this hypothesis in tufted capuchin monkeys using a comparative approach, by investigating the relationships among body mass, sex, stone weight preference, and accuracy in a throwing task. The subject sample consisted of nine monkeys trained to perform an aimed-throwing task in which a food reward could be obtained by throwing a stone into a bucket. We found that 1) the subjects showed a strong mean stone mass preference; 2) the females chose heavier stones than the males, in terms of absolute mean selected stone mass and selected stone mass relative to body mass; 3) subjects threw more accurately when they used stones of preferred mass vs. stones of nonpreferred mass; and 4) overall, the males were more accurate in the throwing task than the females. We conclude that capuchins are highly selective when choosing throwing stones, and that this confers an advantage for throwing accuracy. Our results indicate that the sexually dimorphic pattern in stone mass preference observed among humans does not generalize to Cebus apella. We suggest that researchers examining this pattern in humans in an attempt to explain early hominid patterns of dimorphism and behavior should take into account not only stone weight preference, but also its adaptive advantage. Copyright 2003 Wiley-Liss, Inc.

Improved corrosion resistance of cast carbon steel in sulphur oxides by Alonizing

International Nuclear Information System (INIS)

Holtzer, M.; Dzioba, Z.

1992-01-01

The results of studies on the Alonizing of cast steel and of testing the corrosion resistance of this cast steel in an atmosphere containing 5 to 6% SO 2 + 50% SO 3 at 853 K are described and compared with the results obtained with unalonized cast carbon steel and high-alloy 23Cr-8Ni-2Mo cast steel. The duration of the corrosion tests was 336 hours. The aluminium diffusion layer on cast carbon steel was obtained by holding the specimens in a mixture containing 99% of powered Fe-Al and 1% of NH 4 Cl at 1323 ± 20 K. The holding time was 10 and 20 hours, respectively. The aluminium layer formed on the cast carbon steel was examined by optical microscopy and an X-ray microanalysis. After Alonizing for 10 h the layer had reached a thickness of 950 μm, and contained up to 35% Al. In a mixture of sulphur oxides corrosion rate of the alonized cast carbon steel was by about 600 times lower than of the unalonized cast carbon steel, and by about 50 times lower than that of the 23Cr-8Ni-2Mo cast steel. (orig.) [de

Selected properties of new „duplex” cast steel

Directory of Open Access Journals (Sweden)

S. Pietrowski

2011-10-01

Full Text Available In this paper selected properties of new „duplex” cast steel are presented. The new cast steel was devised in HYDRO-VACUUM company in Grudziądz, where “duplex” cast steel for pump elements is smelted. The goal was to devise a new grade of “duplex” cast steel of better physicochemical properties and cheaper than now applied. It was demonstrated, that there is the possibility of devising the new grade of “duplex” cast steel. It is characterized by higher mechanical properties, similar wear resistance and greater corrosion resistance in 15% water solution of H2SO4 in comparison to now applied “duplex” cast steel. The chemical composition was selected to obtain in microstructure about of 50% ferrite and 50% austenite. It guarantee the highest properties and the lowest costs of its smelting.In the paper results of: the microstructure, Rm, Rp0,2, A5, HB, wear resistance and corrosion resistance in water solution of 15% HCl and H2SO4 acids of new cast steel was presented. They were compared with now applied in HYDRO-VACUUM company “duplex” cast steel.

Use of a general-purpose heat-transfer code for casting simulation

International Nuclear Information System (INIS)

Erickson, W.C.

1975-07-01

The practical use of numerical techniques in simulating casting solidification dictate that a general purpose heat transfer code be used and that results be obtained in an easy-to-analyze format. Color film plotting routines were developed for use with NASA's CINDA-3G heat transfer code; the combination of which meet the above criteria. The subroutine LQSLTR written for SINDA, the successor to CINDA-3G, was verified by comparing calculated results obtained using LQSLTR with those obtained using the specific heat method for handling the heat of fusion. Excellent agreement existed when similar data was used. When the more restrictive requirement of a 1 0 F melting range was used, comparable results were obtained. Uranium and lead rod castings were cast in instrumented graphite molds and the solidification sequence simulated using CINDA-3G. Discrepancies attributed to initial assumptions of instantaneous mold filling, uniform melt temperature, and intimate metal/mold contact were encountered. Further calculations using a model incorporating a gap between the mold and casting showed that the intimate contact assumption could not be used; a three-dimensional model also showed that the thermocouple assemblies used with the platinum--platinum-10 percent rhodium were a significant perturbation to the system. An L-shaped steel casting was simulated and the results compared to those reported in the literature. The experimental data for this casting were reproduced within the accuracy permitted by the thermal conductivity of the sand, thus demonstrating that agreement can be obtained when the mold material does not act as a chill. (U.S.)

Application of artificial tactile sensing approach in kidney-stone-removal laparoscopy.

Science.gov (United States)

Afshari, Elnaz; Najarian, Siamak; Simforoosh, Nasser

2010-01-01

Artificial tactile sensing is a novel method for obtaining different characteristics of a hard object embedded in a soft tissue. In this regard, artificial palpation is one of the most valuable achievements of artificial tactile sensing that can be used in various fields of medicine and more specifically in surgery. In this study, considering the present problems and limitations in kidney-stone-removal laparoscopy, a new application will be presented for artificial tactile sensing approach. Having imitated surgeon's palpation during open surgery and modeled it conceptually, indications of stone existence that appear on the surface of kidney (due to exerting mechanical load) were determined. A number of different cases were created and solved by the software. Using stress distribution contours and stress graphs, it is illustrated that the created stress patterns on the surface of kidney not only show the existence of stone inside, but also its exact location. In fact, the reliability and accuracy of artificial tactile sensing method in detection of kidney stone during laparoscopy is demonstrated by means of finite element analysis. Also, in this paper, the functional principles of tactile system capable of determining the exact location of stone during laparoscopy will be presented.

Novel technologies for the lost foam casting process

Science.gov (United States)

Jiang, Wenming; Fan, Zitian

2018-03-01

Lost foam casting (LFC) is a green precision casting process categorized as a near net forming technology. Yet, despite its popularity, it still suffers from some technological problems, such as poor filling ability of the castings, coarse and non-dense microstructure, low mechanical properties for the Al and Mg LFC processes, and defective carburization for the low carbon steel LFC process. These drawbacks restrict the development and widespread application of the LFC process. To solve these problems, the present study developed several novel LFC technologies, namely, LFC technologies under vacuum and low pressure, vibration solidification, and pressure solidification conditions; expendable shell casting technology; and preparation technology of bimetallic castings based on the LFC process. The results showed that the LFC under vacuum and low pressure evidently improved the filling ability and solved the oxidization problem of the alloys, which is suitable for producing complex and thinwall castings. The vibration and pressure solidifications increased the compactness of the castings and refined the microstructure, significantly improving the mechanical properties of the castings. The expendable shell casting technology could solve the pore, carburization, and inclusion defects of the traditional LFC method, obtaining castings with acceptable surface quality. Moreover, the Al/Mg and Al/Al bimetallic castings with acceptable metallurgical bonding were successfully fabricated using the LFC process. These proposed novel LFC technologies can solve the current technological issues and promote the technological progress of the LFC process.

Effect of Melting Techniques on Ductile Iron castings Properties

Directory of Open Access Journals (Sweden)

Bockus, S.

2006-01-01

Full Text Available The study was designed to investigate the effects of the charge, melting conditions, nodularizing and inoculation on the ductile iron castings properties. Results showed that the temperature and holding time of the melt in an induction furnace and the intensity of spheroidizing effect on the carbon and residual magnesium contents in the ductile iron castings. The same grade of ductile iron may be obtained using different chemical compositions. The castings of ductile iron will be ferritic as-cast only when large amount of pig iron in the charge and in addition some-steps inoculating treatment are used.

SYNTHESIS OF EXPANDER TO PREVENT CONTRACTION OF CEMENT STONE

Directory of Open Access Journals (Sweden)

Elenova Aurika Almazovna

2017-03-01

Full Text Available This article contains the results of studies of the use of additives containing crystallization components significantly affecting the curing of cement, improving the structure of cement stone and concrete. The crystalline component is obtained using the rotary-pulse unit, which provides not only the grinding of agents, but their interaction with each other as well in order to accelerate the hydration and structure formation in cement stone. The degree, and kinetics of hydration, the composition of hydrated phases, the structure of the additives and cement stone was studied using the following methods: x-ray diffraction (XRD, differential thermal analysis (DTA, scanning electron microscope (SEM. Mechanical properties of cement were determined by standard methods and techniques. The expander produced by means of hydrodynamic activation of the sulfoaluminate clinker (SAC consists of ettringite and hydrated calcium silicates, which are characterized by high dispersion rate (less than 10 µm and reactivity as the seed for the crystallization of hydrated compounds. The introduction of the ultrafine additives of the crystalline SAC (within 1-5% was discovered to cause expansion of the cement stone. Implementation of the additives increases cement hydration and contributes to the formation of active centers of crystallization that lead to the fast formation of ettringite, hydrated calcium aluminates and calcium silicates. The activated crystalline additive provides for significant reduction of porosity, initial curing, and high strength of cement stone. In addition, the additive is an expansive component, forming needle-like crystals of ettringite during hydration. These microcrystals grow in the capillaries of cement stone, filling them, and create conditions for improving the crack resistance of cement concrete.

Extracorporeal shock wave lithotripsy (ESWL) vs. ureterorenoscopic (URS) manipulation in proximal ureteric stone.

Science.gov (United States)

Manzoor, Salman; Hashmi, Altaf Hussain; Sohail, Muhammad Ali; Mahar, Feroz; Bhatti, Shahid; Khuhro, Abdul Qayoom

2013-10-01

To compare the stone free rate at one week after extracorporeal shock wave lithotripsy (ESWL) and ureterorenoscopic (URS) manipulation for proximal ureteric stone (10 - 15 mm size). Randomized controlled trial. Sindh Institute of Urology and Transplantation (SIUT), Karachi, from August 2010 to February 2011. One hundred and ninety patients with 10 - 15 mm proximal urteric stone, in each group were treated with ESWL and ureterorenoscopic manipulation by using an 8.0 or 8.5 Fr semi rigid ureteroscope. Intracorporeal lithotripsy was performed by using pneumatic lithoclast. The stone free rate were compared between groups by considering size of stone at one week after procedure. The success rate, retreatment rate, auxiliary procedure and complication rate were compared in each group. Success rate was 49.2% for ESWL and 57.8% for URS (p = 0.008). The re-treatment rate was significantly higher in ESWL group than in URS group (40% vs. 11 and 18% in URS group). Although ESWL is regarded as the preferred choice of treatment for proximal ureteric stone, the present results suggest that ureterorenoscopic manipulation with intracorporeal lithotripsy is a safe alternative, with an advantage of obtaining an earlier or immediate stone-free status. Laparoscopic approaches are reasonable alternatives in cases, where ESWL and URS have failed.

Upper urinary tract stone disease in patients with poor performance status: active stone removal or conservative management?

Science.gov (United States)

Yamashita, Shimpei; Kohjimoto, Yasuo; Hirabayashi, Yasuo; Iguchi, Takashi; Iba, Akinori; Higuchi, Masatoshi; Koike, Hiroyuki; Wakamiya, Takahito; Nishizawa, Satoshi; Hara, Isao

2017-11-16

It remains controversial as to whether active stone removal should be performed in patients with poor performance status because of their short life expectancy and perioperative risks. Our objectives were to evaluate treatment outcomes of active stone removal in patients with poor performance status and to compare life prognosis with those managed conservatively. We retrospectively reviewed 74 patients with Eastern Cooperative Oncology Group performance status 3 or 4 treated for upper urinary tract calculi at our four hospitals between January 2009 and March 2016. Patients were classified into either surgical treatment group or conservative management group based on the presence of active stone removal. Stone-free rate and perioperative complications in surgical treatment group were reviewed. In addition, we compared overall survival and stone-specific survival between the two groups. Cox proportional hazards analysis was performed to investigate predictors of overall survival and stone-specific survival. Fifty-two patients (70.3%) underwent active stone removal (surgical treatment group) by extracorporeal shock wave lithotripsy (n = 6), ureteroscopy (n = 39), percutaneous nephrolithotomy (n = 6) or nephrectomy (n = 1). The overall stone-free rate was 78.8% and perioperative complication was observed in nine patients (17.3%). Conservative treatment was undergone by 22 patients (29.7%) (conservative management group). Two-year overall survival rates in surgical treatment and conservative management groups were 88.0% and 38.4%, respectively (p performance status could be performed safely and effectively. Compared to conservative management, surgical stone treatment achieved longer overall survival and stone-specific survival.

The effect of concentration on the structure and crystallinity of a cementitious waste form for caustic wastes

International Nuclear Information System (INIS)

Chung, Chul-Woo; Turo, Laura A.; Ryan, Joseph V.; Johnson, Bradley R.; McCloy, John S.

2013-01-01

Highlights: ► Cast Stone: Portland cement, fly ash, blast furnace slag, and simulated nuclear waste. ► Caustic secondary waste from the off-gas of a vitrification process was targeted. ► Crystallinity, micro- and mesostructure, and engineering properties characterized. ► Waste concentration varied from 0 to 2.5 M, but caused minimal changes. ► Cast Stone shows good compositional versatility as a secondary waste form. -- Abstract: Cement-based waste forms have long been considered economical technologies for disposal of various types of waste. A solidified cementitious waste form, Cast Stone, has been identified to immobilize the radioactive secondary waste from vitrification processes. In this work, Cast Stone was considered for a Na-based caustic liquid waste, and its physical properties were analyzed as a function of liquid waste loading up to 2 M Na. Differences in crystallinity (phase composition), microstructure, mesostructure (pore size distribution and surface area), and macrostructure (density and compressive strength) were investigated using various analytical techniques, in order to assess the suitability of Cast Stone as a chemically durable waste. It was found that the concentration of secondary waste simulant (caustic waste) had little effect on the relevant engineering properties of Cast Stone, showing that Cast Stone could be an effective and tolerant waste form for a wide range of concentrations of high sodium waste

Management of ureteric stone in pediatric patients

Directory of Open Access Journals (Sweden)

Eugene Minevich

2010-01-01

Full Text Available The management of ureteral stones in children is becoming more similar to that in adults. A number of factors must be taken into account when selecting one′s choice of therapy for ureteral stone in children such as the size of the stone, its location, its composition, and urinary tract anatomy. Endoscopic lithotripsy in children has gradually become a major technique for the treatment of ureteral stones. The stone-free rate following urteroscopic lithotripsy for ureteral stones has been reported in as high as 98.5-100%. The safety and efficacy of Holmium:YAG laser lithotripsy make it the intracorporeal lithotriptor of choice. Given its minimally invasive features, extracorporeal shock wave lithotripsy (ESWL has become a primary mode of treatment for the pediatric patients with reno-ureteral stones. Stone-free rates have been reported from 59% to 91% although some patients will require more than one treatment session for stone clearance. It appears that the first-line of therapy in the child with distal and mid-ureteral stones should be ureteroscopic lithotripsy. While ESWL is still widely considered the first-line therapy for proximal ureteral calculi, there is an increasing body of evidence that shows that endoscopic or ESWL are equally safe and efficacious in those clinical scenarios. Familiarity with the full spectrum of endourological techniques facilitates a minimally invasive approach to pediatric ureteral stones.

Fibreglass Total Contact Casting, Removable Cast Walkers, and Irremovable Cast Walkers to Treat Diabetic Neuropathic Foot Ulcers: A Health Technology Assessment

Science.gov (United States)

Costa, Vania; Tu, Hong Anh; Wells, David; Weir, Mark; Holubowich, Corinne; Walter, Melissa

2017-01-01

Background Diabetic neuropathic foot ulcers are a risk factor for lower leg amputation. Many experts recommend offloading with fibreglass total contact casting, removable cast walkers, and irremovable cast walkers as a way to treat these ulcers. Methods We completed a health technology assessment, which included an evaluation of clinical benefits and harms, value for money, and patient preferences for offloading devices. We performed a systematic literature search on August 17, 2016, to identify randomized controlled trials that compared fibreglass total contact casting, removable cast walkers, and irremovable cast walkers with other treatments (offloading or non-offloading) in patients with diabetic neuropathic foot ulcers. We developed a decision-analytic model to assess the cost-effectiveness of fibreglass total contact casting, removable cast walkers, and irremovable cast walkers, and we conducted a 5-year budget impact analysis. Finally, we interviewed people with diabetes who had lived experience with foot ulcers, asking them about the different offloading devices and the factors that influenced their treatment choices. Results We identified 13 randomized controlled trials. The evidence suggests that total contact casting, removable cast walkers, and irremovable cast walkers are beneficial in the treatment of neuropathic, noninfected foot ulcers in patients with diabetes but without severe peripheral arterial disease. Compared to removable cast walkers, ulcer healing was improved with total contact casting (moderate quality evidence; risk difference 0.17 [95% confidence interval 0.00–0.33]) and irremovable cast walkers (low quality evidence; risk difference 0.21 [95% confidence interval 0.01–0.40]). We found no difference in ulcer healing between total contact casting and irremovable cast walkers (low quality evidence; risk difference 0.02 [95% confidence interval −0.11–0.14]). The economic analysis showed that total contact casting and irremovable

Correlation between Copper, Zinc and some lipids in serum, bile and stones of patients with gall stone disease

International Nuclear Information System (INIS)

Abu-Farsakh, F.

1997-01-01

Measurements of Cu, Zn and some lipid concentrations were carried out in serum, bile and gall stone samples collected from 76 patients undergoing surgery for removal of gall stones. The results showed that Cu and Zn were present in micromolar concentration in bile (average Cu concentration = 13.4 ± 0.92, average Zn concentration = 13.4 ± 1.05) and gall stones (average Cu concentration = 2.8 ± 0.16, average Zn concentration = 1.8 ± 0.16 mmol/ g stone). Cross-tabulation of the results showed significant positive linear correlations (p< 0.01) between stone Zn vs. bile cholesterol (r = 0.253), stone Zn vs. bile bilirubin (r = 0.396) (in mixed stones only). This suggested that the more hydrophobic the bile sample, the more Zn co-precipitate with cholesterol or bilirubin. (author). 17 refs., 3 tabs

Stone heterogeneity index as the standard deviation of Hounsfield units: A novel predictor for shock-wave lithotripsy outcomes in ureter calculi.

Science.gov (United States)

Lee, Joo Yong; Kim, Jae Heon; Kang, Dong Hyuk; Chung, Doo Yong; Lee, Dae Hun; Do Jung, Hae; Kwon, Jong Kyou; Cho, Kang Su

2016-04-01

We investigated whether stone heterogeneity index (SHI), which a proxy of such variations, was defined as the standard deviation of a Hounsfield unit (HU) on non-contrast computed tomography (NCCT), can be a novel predictor for shock-wave lithotripsy (SWL) outcomes in patients with ureteral stones. Medical records were obtained from the consecutive database of 1,519 patients who underwent the first session of SWL for urinary stones between 2005 and 2013. Ultimately, 604 patients with radiopaque ureteral stones were eligible for this study. Stone related variables including stone size, mean stone density (MSD), skin-to-stone distance, and SHI were obtained on NCCT. Patients were classified into the low and high SHI groups using mean SHI and compared. One-session success rate in the high SHI group was better than in the low SHI group (74.3% vs. 63.9%, P = 0.008). Multivariate logistic regression analyses revealed that smaller stone size (OR 0.889, 95% CI: 0.841-0.937, P < 0.001), lower MSD (OR 0.995, 95% CI: 0.994-0.996, P < 0.001), and higher SHI (OR 1.011, 95% CI: 1.008-1.014, P < 0.001) were independent predictors of one-session success. The radiologic heterogeneity of urinary stones or SHI was an independent predictor for SWL success in patients with ureteral calculi and a useful clinical parameter for stone fragility.

Advances in percutaneous stone surgery

OpenAIRE

Hartman, Christopher; Gupta, Nikhil; Leavitt, David; Hoenig, David; Okeke, Zeph; Smith, Arthur

2015-01-01

Treatment of large renal stones has changed considerably in recent years. The increasing prevalence of nephrolithiasis has mandated that urologists perform more surgeries for large renal calculi than before, and this has been met with improvements in percutaneous stone surgery. In this review paper, we examine recent developments in percutaneous stone surgery, including advances in diagnosis and preoperative planning, renal access, patient position, tract dilation, nephroscopes, lithotripsy, ...

THE CORROSION BEHAVIOR AND WEAR RESISTANCE OF GRAY CAST IRON

Directory of Open Access Journals (Sweden)

Lina F. Kadhim

2018-01-01

Full Text Available Gray cast iron has many applications as pipes , pumps and valve bodies where it has influenced by heat and contact with other solutions . This research has studied the corrosion behavior and Vickers hardness of gray cast iron by immersion in four strong alkaline solutions (NaOH, KOH, Ca(OH2, LiOHwith three concentrations (1%,2%,3% of each solution. Dry sliding wear has carried out before and after the heat treatments (stress relief ,normalizing, hardening and tempering. In this work ,maximum wear strength has obtained at tempered gray cast iron and minimum corrosion rate has obtained in LiOH solution by forming protective white visible oxide layer.

Long-distance stone transport and pigment use in the earliest Middle Stone Age

Science.gov (United States)

Brooks, Alison S.; Yellen, John E.; Potts, Richard; Behrensmeyer, Anna K.; Deino, Alan L.; Leslie, David E.; Ambrose, Stanley H.; Ferguson, Jeffrey R.; d’Errico, Francesco; Zipkin, Andrew M.; Whittaker, Scott; Post, Jeffrey; Veatch, Elizabeth G.; Foecke, Kimberly; Clark, Jennifer B.

2018-04-01

Previous research suggests that the complex symbolic, technological, and socioeconomic behaviors that typify Homo sapiens had roots in the middle Pleistocene methods. Hominins at these sites made prepared cores and points, exploited iron-rich rocks to obtain red pigment, and procured stone tool materials from ≥25- to 50-kilometer distances. Associated fauna suggests a broad resource strategy that included large and small prey. These practices imply notable changes in how individuals and groups related to the landscape and to one another and provide documentation relevant to human social and cognitive evolution.

Bacteriological study and structural composition of staghorn stones removed by the anatrophic nephrolithotomic procedure

Directory of Open Access Journals (Sweden)

Hamid Shafi

2013-01-01

Full Text Available This study was conducted to determine the composition of staghorn stones and to assess the proportion of infected stones as well as the correlation between infection in the stones and bacteria grown in urine. Samples of 45 consecutive stones removed through anatrophic nephrolithotomic procedures were taken from the operation site and samples of urine were obtained by simultaneous bladder catheterization. The frequency of infection in the stones and correlation between infection of stone and urine samples were determined with respect to the composition of the stones. Twenty-two males and 23 females, with respective mean ages of 48.3 ± 15.6 years and 51 ± 7.4 years, were studied. The stone and urine cultures yielded positive results in ten and 16 patients, respectively, of a total of 45 patients (22.2% and 35.5%, respectively. Calcium oxalate was the main constituent of staghorn stones, seen in 31 patients (68.8%, uric acid in 12 patients (26.6% and struvite and/or calcium phosphate in 11 patients (24.4%. In seven of ten stones with bacterial growth, bacteria were isolated from urine cultures as well, which accounted for a concordance rate of 70%. The bacteria grown in the stone were the cause of urinary tract infection (UTI in 43.5% of the cases. Stone infection was significantly associated with UTI (OR = 6.47; 95% CI 1.43-31.7, P = 0.021 and presence of phosphate in the stones (OR = 18, 95% CI 3.28-99.6, P = 0.0006. E. coli was the most common bacteria grown from the stones, and was isolated in 50% of the cases; Ureaplasma urealyticum was the most common organism causing UTI, grown in 62.5% of the urine samples. There was a high concordance rate between bacteria in the stones and urine. These findings indicate that the urine culture can provide information for selection of an appropriate anti-microbial agent for stone sterilization. In addition, preventing re-growth or recurrence of stones and treatment of post-surgical infections would be

PHYSICOCHEMICAL AND ANTIBACTERIAL PROPERTIES OF PLA-CHITOSAN BLENDS OBTAINED BY CASTING WITH POTENTIAL USE AS AGRICULTURAL MULCH FILMS

Directory of Open Access Journals (Sweden)

Danila Merino

2016-03-01

Full Text Available PLA-Chitosan films compatibilized with hexamethylenediisocyanate (HDI were obtained by casting and subsequent hot pressing. The films were prepared with different contents of chitosan (CS and then its physicochemical properties were studied by Fourier Transform infrared spectroscopy (FTIR, thermogravimetric analysis (TGA, differential scanning calorimetry (DSC, optical microscopy (OM and X-ray diffraction (XRD. It was found that the compatibilizing agent reacts completely and that chitosan affects the thermal properties of the films decreasing their decomposition temperatures, glass transition temperature (Tg and melting (Tm and increase its crystallinity. From the functional standpoint, antimicrobial properties of each blend were tested against Pseudomonas syringae pv tomato DC-3000. The increase in chitosan content was proportional to the antimicrobial effect allowing project its potential application in the agronomic field.

Optimum nutrition for kidney stone disease.

Science.gov (United States)

Heilberg, Ita P; Goldfarb, David S

2013-03-01

We summarize the data regarding the associations of individual dietary components with kidney stones and the effects on 24-hour urinary profiles. The therapeutic recommendations for stone prevention that result from these studies are applied where possible to stones of specific composition. Idiopathic calcium oxalate stone-formers are advised to reduce ingestion of animal protein, oxalate, and sodium while maintaining intake of 800 to 1200 mg of calcium and increasing consumption of citrate and potassium. There are few data regarding dietary therapy of calcium phosphate stones. Whether the inhibitory effect of citrate sufficiently counteracts increasing urine pH to justify more intake of potassium and citrate is not clear. Reduction of sodium intake to decrease urinary calcium excretion would also be expected to decrease calcium phosphate stone recurrence. Conversely, the most important urine variable in the causation of uric acid stones is low urine pH, linked to insulin resistance as a component of obesity and the metabolic syndrome. The mainstay of therapy is weight loss and urinary alkalinization provided by a more vegetarian diet. Reduction in animal protein intake will reduce purine ingestion and uric acid excretion. For cystine stones, restriction of animal protein is associated with reduction in intake of the cystine precursor methionine as well as cystine. Reduction of urine sodium results in less urine cystine. Ingestion of vegetables high in organic anion content, such as citrate and malate, should be associated with higher urine pH and fewer stones because the amino acid cystine is soluble in more alkaline urine. Because of their infectious origin, diet has no definitive role for struvite stones except for avoiding urinary alkalinization, which may worsen their development. Published by Elsevier Inc.

MATH MODELING OF CAST FINE-GRAINED CONCRETE WITH INDUSTRIAL WASTES OF COPPER PRODUCTION

Directory of Open Access Journals (Sweden)

Tsybakin Sergey Valerievich

2017-10-01

Full Text Available Subject: applying mineral microfillers on the basis of technogenic wastes of non-ferrous metallurgy in the technology of cast and self-compacting concrete. The results of experiments of scientists from Russia, Kazakhstan, Poland and India show that copper smelting granulated slag can be used when grinding construction cements as a mineral additive up to 30 % without significantly reducing activity of the cements. However, there are no results of a comprehensive study of influence of the slag on plastic concrete mixtures. Research objectives: establishment of mathematical relationship of the influence of copper slag on the compressive strength and density of concrete after 28 days of hardening in normal conditions using the method of mathematical design of experiments; statistical processing of the results and verification of adequacy of the developed model. Materials and methods: mathematical experimental design was carried out as a full 4-factor experiment using rotatable central composite design. The mathematical model is selected in the form of a polynomial of the second degree using four factors of the response function. Results: 4-factor mathematical model of concrete strength and density after curing is created, regression equation is derived for dependence of the 28-days strength function and density on concentration of the cement stone, true water-cement ratio, dosage of fine copper slag and superplasticizer on the basis of ether polycarboxylates. Statistical processing of the results of mathematical design of experiments is carried out, estimate of adequacy of the constructed mathematical model is obtained. Conclusions: it is established that introduction of copper smelting slag in the range of 30…50 % by weight of cement positively affects the strength of concrete when used together with the superplasticizer. Increasing the dosage of superplasticizer in excess of 0.16 % of the dry component leads to a decrease in the strength of cast

Modeling of TiAl Alloy Grating by Investment Casting

Directory of Open Access Journals (Sweden)

Yi Jia

2015-12-01

Full Text Available The investment casting of TiAl alloys has become the most promising cost-effective technique for manufacturing TiAl components. This study aimed to investigate a series of problems associated with the investment casting of TiAl alloys. The mold filling and solidification of this casting model were numerically simulated using ProCAST. Shrinkage porosity was quantitatively predicted by a built-in feeding criterion. The results obtained from the numerical simulations were compared with experiments, which were carried out on Vacuum Skull Furnace using an investment block mold. The investment casting of TiAl grating was conducted for verifying the correctness and feasibility of the proposed method. The tensile test results indicated that, at room temperature, the tensile strength and elongation were approximately 675 MPa and 1.7%, respectively. The microstructure and mechanical property of the investment cast TiAl alloy were discussed.

ORIGINAL PAPER ORIG ORIG Percutaneous stone removal

African Journals Online (AJOL)

Percutaneous nephrolithotomy (PCNL) is an effective procedure to treat patients with complex renal stones,. e.g. staghorn calculi and stones greater than 20 mm in diameter. The treatment of choice for small, less com- plex renal stones is extracorporeal shock-wave litho- tripsy (ESWL).1 We have treated renal stones mainly.

Gradient porous hydroxyapatite ceramics fabricated by freeze casting method

International Nuclear Information System (INIS)

Zuo Kaihui; Zhang Yuan; Jiang Dongliang; Zeng Yuping

2011-01-01

By controlling the cooling rates and the composition of slurries, the gradient porous hydroxyapatite ceramics are fabricated by the freeze casting method. According to the different cooling rate, the pores of HAP ceramics fabricated by gradient freeze casting are divided into three parts: one is lamellar pores, another is column pore and the last one is fine round pores. The laminated freeze casting is in favour of obtaining the gradient porous ceramics composed of different materials and the ceramics have unclear interfaces.

Plastic-casting intrinsic-surface unique identifier (tag)

International Nuclear Information System (INIS)

Palm, R.G.; De Volpi, A.

1995-04-01

This report describes the development of an authenticated intrinsic-surf ace tagging method for unique- identification of controlled items. Although developed for control of items limited by an arms control treaty, this method has other potential applications to keep track of critical or high-value items. Each tag (unique-identifier) consists of the intrinsic, microscopic surface topography of a small designated area on a controlled item. It is implemented by making a baseline plastic casting of the designated tag area and usually placing a cover (for example, a bar-code label) over this area to protect the surface from environmental alteration. The plastic casting is returned to a laboratory and prepared for high-resolution scanning electron microscope imaging. Several images are digitized and stored for use as a standard for authentication of castings taken during future inspections. Authentication is determined by numerically comparing digital images. Commercially available hardware and software are used for this tag. Tag parameters are optimized, so unique casting images are obtained from original surfaces, and images obtained from attempted duplicate surfaces are detected. This optimization uses the modulation transfer function, a first principle of image analysis, to determine the parameters. Surface duplication experiments confirmed the optimization

Cold deformation of ADI castings: Martensitic transformation

International Nuclear Information System (INIS)

Navea, Lilian R; Mannheim, Rodolfo M; Garin, Jorge L

2004-01-01

Research and applications in austempered ductile iron (ADI castings) have recently undergone noticeable progress in the industrialized world, becoming a highly competitive engineering material. The notable properties of these castings derive from their austenitic matrix stabilized by carbon, a thermally stable austenite during the austenizing process but possibly turning into martensite when undergoing plastic deformation. This work aims to study the changing structure of an ADI casting caused by one directional cold lamination. The samples that were studied were obtained from two nodular castings, one without alloying and the other alloyed with Cu, Ni and Mo. The samples were austenized in the first stage of the austempering process at 910 o C for 80 min. Then in the second stage the unalloyed samples were austempered at 410 o C for 10 min and the alloyed samples for 120 min. After the thermal treatment, the test pieces were deformed 0% to 25% by cold lamination. The quantification of the phases was performed using x-ray diffraction and the metallographic study using optic and Scanning Electronic Microscopy. The results show that the martensitic phase obtained by deformation is a very fine structure that evolves into a thicker one when the deformation of the samples increases (CW)

Centrifugal vacuum casting for fuel cladding tube blanks

International Nuclear Information System (INIS)

Zelenskii, V.F.; Neklyudov, I.M.; Chernyi, B.P.; Zeidlits, M.P.; Vanzha, A.F.; Rubashko, V.G.; Ryabchikov, L.N.; Smirnov, Y.K.; Bespalova, V.R.; Mashkarova, V.T.; Rybal'chenko, N.D.

1990-01-01

An advanced technique for making tube blanks with an acceptable level of nonmetallic inclusions is vacuum induction melting combined with centrifugal casting, as the latter gives a cylindrical casting having an axial hole, while the cast metal has elevated density and contains fewer nonmetallic inclusions than does the metal cast in a stationary mold. The reduction in the nonmetallic inclusions occurs because of increased rates of floating up in the rotating mold on account of the centrifugal force and the rejection to the inner surface. One can choose the parameters such as the pouring speed, rotational speed, mold cooling, and liquid-metal temperature and can introduce a deoxidizer to remove the nonmetallic inclusions or reduce the grain size of them and produce an appropriate cast structure and obtain a metal whose quality is the same as that on vacuum induction melting with secondary arc remelting. For these purposes, the authors have developed centrifugal-casting machines for use under vacuum or in inert gases with horizontal and vertical mold rotation axes

77 FR 27245 - Big Stone National Wildlife Refuge, Big Stone and Lac Qui Parle Counties, MN

Science.gov (United States)

2012-05-09

... DEPARTMENT OF THE INTERIOR Fish and Wildlife Service [FWS-R3-R-2012-N069; FXRS1265030000S3-123-FF03R06000] Big Stone National Wildlife Refuge, Big Stone and Lac Qui Parle Counties, MN AGENCY: Fish and... plan (CCP) and environmental assessment (EA) for Big Stone National Wildlife Refuge (Refuge, NWR) for...

The effect of inclined position on stone free rates in patients with lower caliceal stones during SWL session

Directory of Open Access Journals (Sweden)

Basri Cakiroglu

2015-03-01

Full Text Available Objective: To compare the outcomes of shock wave lithotripsy (SWL combined with inclined position and SWL alone in patients with lower pole calyx stones. Methods: Seven hundred forty patients who underwent SWL treatment for lower pole renal stones with a total diameter of 2 cm or less were prospectively randomized into two groups. They were comparable in terms of age, sex, and stone diameters. Patients with lower calyceal stones (4-20 mm were randomized to SWL (368 patients or SWL with simultaneous inclination (372 patients with 30o head down Trendelenburg position. Shock wave and session numbers were standardized according to stone size. Additional standardized shock waves were given to patients with stone fragments determined by kidney urinary bladder film and ultrasound at weeks 1, 4, 10. Results: The overall stone free rate (SFR was 73% (268/368 in patients with SWL alone and 81% (300/372 in SWL with inclination at the end of 12th week (p = 0.015. No significant adverse events were noted in both treatment groups. Conclusion: Simultaneous inclination of patients during SWL session increase SFR in lower caliceal stones significantly compared to SWL treatment alone.

Stone comminution correlates with the average peak pressure incident on a stone during shock wave lithotripsy.

Science.gov (United States)

Smith, N; Zhong, P

2012-10-11

To investigate the roles of lithotripter shock wave (LSW) parameters and cavitation in stone comminution, a series of in vitro fragmentation experiments have been conducted in water and 1,3-butanediol (a cavitation-suppressive fluid) at a variety of acoustic field positions of an electromagnetic shock wave lithotripter. Using field mapping data and integrated parameters averaged over a circular stone holder area (R(h)=7 mm), close logarithmic correlations between the average peak pressure (P(+(avg))) incident on the stone (D=10 mm BegoStone) and comminution efficiency after 500 and 1000 shocks have been identified. Moreover, the correlations have demonstrated distinctive thresholds in P(+(avg)) (5.3 MPa and 7.6 MPa for soft and hard stones, respectively), that are required to initiate stone fragmentation independent of surrounding fluid medium and LSW dose. These observations, should they be confirmed using other shock wave lithotripters, may provide an important field parameter (i.e., P(+(avg))) to guide appropriate application of SWL in clinics, and facilitate device comparison and design improvements in future lithotripters. Copyright © 2012 Elsevier Ltd. All rights reserved.

The casting of western sculpture during the XIXth century: sand casting versus lost wax casting

NARCIS (Netherlands)

Beentjes, T.P.C.

2014-01-01

This paper will discuss research into bronze casting techniques as practiced during the XIXth and early XXth century. Both natural sand casting (fonte au sable naturel) and lost wax casting (fonte à la cire perdue) were employed during this period and sometimes rivalled for commissions. Before the

The adherence in the union stone-mortar

Directory of Open Access Journals (Sweden)

Rodríguez García, María Reyes

1994-06-01

Full Text Available Stones placates present a wide of problems that result in the fall of plates. One of the causes is the lack of adherence stone-mortar. We considered a study to determine the adherence between several cement mortars (1:3, 1:5, 1:7, 1:9 and a especial mortar prepared with latex and stones (white granite, pink granites, black granites, white marble and cream limestones. The results obtained suggest that only adequate adherence rates (higher than 3 kgf/cm² achieved with cement mortar 1:3 and especial mortar. Besides it is observed that in the stones studied there is no relation between adherence and the absorption values.

Los aplacados de piedra presentan una extensa patología que se traduce en la caída de las placas colocadas. Una de las causas es la falta de adherencia mortero-piedra. El estudio se realiza para determinar la tensión de adherencia entre diversos morteros de cemento (1:3, 1:5, 1:7, 1:9 y otro compuesto por mortero y látex y piedras (granito blanco, granitos rosa, granitos negros, mármol blanco y calizas crema. De los resultados obtenidos se deduce que los únicos morteros que permiten valores de adherencia aceptables (superiores a 3 kp/cm² son el mortero de cemento 1:3 y el especial. Igualmente se comprueba que, en las piedras estudiadas, no existe relación alguna entre la adherencia y la absorción de agua.

Self-supported carbon electrodes obtained by tape casting

Directory of Open Access Journals (Sweden)

Rubio-Marcos, F.

2006-06-01

Full Text Available This paper describes the preparation and electrochemical response of self-supported carbon electrodes prepared by tape casting. The dc electrical conductivity, σ, of the electrodes was determined by four-wire resistance measurements and a relation between the graphite/organic additives ratio and the electrical conductivity was established. The application of these self-supported carbon electrodes as working electrodes in analytical techniques was also evaluated using norepinephrine as electroactive substance in cyclic voltammetry and chronoamperometry. The results were compared with the traditional electrodes, carbon paste electrodes (CPEs, showing that the new self-supported carbon electrodes had both lower background noise and higher analytical response.

Este artículo describe la preparación y respuesta electroquímica de electrodos de carbono autosoportados preparados mediante colado en cinta. La conductividad eléctrica en corriente continua de este nuevo tipo de electrodos de carbono se ha determinado usando el método de cuatro puntas y se ha establecido una relación ente la relación grafito/aditivos orgánicos y la conductividad eléctrica. La aplicación de estos electrodos autosoportados como electrodos de trabajo en diversas técnicas electroanalíticas también se ha evaluado, empleando norepinefrina como analito en voltametría cíclica y en cronoamperometría. Los resultados se compararon con los obtenidos empleando los electrodos de pasta de carbono tradicionales como electrodos de trabajo, viéndose que la señal de los nuevos electrodos autosoportados poseía menor ruido de fondo y mayor respuesta analítica.

Extracorporeal Shock Wave Lithotripsy (ESWL) vs. Ureterorenoscopic (URS) Manipulation in Proximal Ureteric Stone

International Nuclear Information System (INIS)

Manzoor, S.; Khuhro, A.Q.; Hashmi, A.H.; Sohail, M.A.; Mahar, F.; Bhatti, S.

2013-01-01

Objective: To compare the stone free rate at one week after extracorporeal shock wave lithotripsy (ESWL) and ureterorenoscopic (URS) manipulation for proximal ureteric stone (10 - 15 mm size). Study Design: Randomized controlled trial. Place and Duration of Study: Sindh Institute of Urology and Transplantation (SIUT), Karachi, from August 2010 to February 2011. Methodology: One hundred and ninety patients with 10 - 15 mm proximal urteric stone, in each group were treated with ESWL and ureterorenoscopic manipulation by using an 8.0 or 8.5 Fr semi rigid ureteroscope. Intracorporeal lithotripsy was performed by using pneumatic lithoclast. The stone free rate were compared between groups by considering size of stone at one week after procedure. The success rate, retreatment rate, auxiliary procedure and complication rate were compared in each group. Results: Success rate was 49.2% for ESWL and 57.8% for URS (p = 0.008). The re-treatment rate was significantly higher in ESWL group than in URS group (40% vs. 11 and 18% in URS group). Conclusion: Although ESWL is regarded as the preferred choice of treatment for proximal ureteric stone, the present results suggest that ureterorenoscopic manipulation with intracorporeal lithotripsy is a safe alternative, with an advantage of obtaining an earlier or immediate stone-free status. Laparoscopic approaches are reasonable alternatives in cases, where ESWL and URS have failed. (author)

Advances in percutaneous stone surgery.

Science.gov (United States)

Hartman, Christopher; Gupta, Nikhil; Leavitt, David; Hoenig, David; Okeke, Zeph; Smith, Arthur

2015-01-01

Treatment of large renal stones has changed considerably in recent years. The increasing prevalence of nephrolithiasis has mandated that urologists perform more surgeries for large renal calculi than before, and this has been met with improvements in percutaneous stone surgery. In this review paper, we examine recent developments in percutaneous stone surgery, including advances in diagnosis and preoperative planning, renal access, patient position, tract dilation, nephroscopes, lithotripsy, exit strategies, and post-operative antibiotic prophylaxis.

Review of the continuous casting of steel by strip casting technology. Twin roll method system

International Nuclear Information System (INIS)

Ibarrondo, I.

2008-01-01

In order to compete in the future steel market and to maintain market share, the steel makers will need to use new efficient technologies capable of supplying steel strip products of high quality at low cost. In this way, the strip casting technology by twin rol method is one of the most important research are in the iron and steel industry today. This review makes a general description of the strip casting technology as well as its different steps, such us; metal delivery and casting, solidification process, hot rolling reduction step, etc. Through mathematical and physical models, the influence on microstructure texture surface quality and mechanical properties of the materials obtained by this method are described as a function of processing parameters, specially the roughness of the rolls. the manufacturing of carbon, stainless and electrical steels involves smaller capital and operating cost, lower gas emissions, and an opportunity to create new grades due to a faster solidification rate that leads to a different solidification structures. In sight of all this it is likely that Strip Casting technology will make a profound impact on the manufacturing landscape of the 21 s t century. (Author) 177 refs

Effect of stone coverage on soil erosion

Science.gov (United States)

Jomaa, S.; Barry, D. A.; Heng, B. P.; Brovelli, A.; Sander, G. C.; Parlange, J.

2010-12-01

Soil surface coverage has a significant impact on water infiltration, runoff and soil erosion yields. In particular, surface stones protect the soils from raindrop detachment, they retard the overland flow therefore decreasing its sediment transport capacity, and they prevent surface sealing. Several physical and environmental factors control to what extent stones on the soil surface modify the erosion rates and the related hydrological response. Among the most important factors are the moisture content of the topsoil, stone size, emplacement, coverage density and soil texture. Owing to the different inter-related processes, there is ambiguity concerning the quantitative effect of stones, and process-based understanding is limited. Experiments were performed (i) to quantify how stone features affect sediment yields, (ii) to understand the local effect of isolated surface stones, that is, the changes of the soil particle size distribution in the vicinity of a stone and (iii) to determine how stones attenuate the development of surface sealing and in turn how this affects the local infiltration rate. A series of experiments using the EPFL 6-m × 2-m erosion flume were conducted at different rainfall intensities (28 and 74 mm h-1) and stone coverage (20 and 40%). The total sediment concentration, the concentration of the individual size classes and the flow discharge were measured. In order to analyze the measurements, the Hairsine and Rose (HR) erosion model was adapted to account for the shielding effect of the stone cover. This was done by suitably adjusting the parameters based on the area not covered by stones. It was found that the modified HR model predictions agreed well with the measured sediment concentrations especially for the long time behavior. Changes in the bulk density of the topsoil due to raindrop-induced compaction with and without stone protection revealed that the stones protect the upper soil surface against the structural seals resulting in

The Structure of the Silumin Coat on Alloy Cast Steels

Directory of Open Access Journals (Sweden)

T. Szymczak

2012-04-01

Full Text Available The work presents the analysis results of the structure of the coat obtained by dipping in silumin AlSi5 of two grades of alloy cast steel: GX6CrNiTi18-10 (LH18N9T and GX39Cr13 (LH14. The temperature of the silumin bath was 750±5°C, and the hold-up time of the cast steel element τ = 180 s. The absolute thickness of the coat obtained in the given conditions was g = 104 μm on cast steel GX6CrNiTi18-10 and g = 132 μm on GX39Cr13. The obtained coat consisted of three layers of different phase structure. The first layer from the base “g1`” was constructed of the phase AlFe including Si and alloy additives of the tested cast steel grades: Cr and Ni (GX6CrNiTi18-10 and Cr (GX39Cr13. The second layer “g1``” of intermetallic phases AlFe which also contains Si and Cr crystallizes on it. The last, external layer “g2” of the coat consists of the silumin containing the intermetallic phases AlFeSi which additionally can contain alloy additives of the cast steel. It was shown that there were no carbides on the coat of the tested cast steels which are the component of their microstructure, as it took place in the case of the coat on the high speed steels.

Intraperitoneal stone migration during percutaneos nephrolithotomy

Directory of Open Access Journals (Sweden)

Akif Diri

2014-12-01

Full Text Available Percutaneos nephrolithotomy (PNL is the standard care for renal stones larger than 2 cm. The procedure has some major and minor complications. Renal pelvis laceration and stone migration to the retroperitoneum is one of the rare condition. We report the first case of intraperitoneal stone migration during PNL.

Stone stability under non-uniform flow

NARCIS (Netherlands)

Hoan, N.T.

2008-01-01

Despite the fact that many studies on the stability of stones in bed protections under flowing water have been conducted, our knowledge is still far from advanced and reliable. Issues like how to quantify the hydraulic loads exerted on the stones on a bed and the associated stability of the stones

Evolution of stone management in Australia.

Science.gov (United States)

Lee, Ming-Chak; Bariol, Simon Virgil

2011-11-01

What's known on the subject? and What does the study add? There is very little contemporary data regarding stone management in Australia. This study assesses the impact of technological advances on stone management practises, and raises questions as to why there is an increasing rate of intervention for stone disease in Australia. Knowledge of management trends as demonstrated in this paper give individual surgeons a guideline for contemporary practise in this country. • To examine trends in the operative management of upper urinary tract stone disease in Australia over the past 15 years. • The Medicare Australia and Australian Institute of Health and Welfare databases were used to determine the annual number of renal colic presentations and procedural interventions undertaken for stone disease. • In Australia over the past 15 years, the annual number of procedural interventions for upper urinary tract stones has increased, primarily due to the rising number of endoscopic procedures performed. • During this period, shock wave lithotripsy numbers have remained steady whilst open and percutaneous procedures have been in decline. • The introduction of and subsequent preference for less invasive techniques has changed the management pathway of patients presenting with stone disease in Australia. • Further studies are necessary to determine whether this escalation in endoscopic procedures is due to an increase in the incidence of stone disease, earlier detection, a lower intervention threshold or a higher retreatment rate. © 2011 THE AUTHORS. BJU INTERNATIONAL © 2011 BJU INTERNATIONAL.

Aluminide protective coatings on high–temperature creep resistant cast steel

OpenAIRE

J. Kubicki; A. Kochmańska

2009-01-01

This paper presents the results of research on aluminide protective coatings manufactured on high–temperature creep resistant cast steel. The main purpose of these coatings is protection against the high temperature corrosion, especially at high carburizing potential atmosphere. Coatings were obtained on cast steel type G–XNiCrSi36–18 with the following methods: pack cementation, paste method, cast method and slurry cementation. The phase composition, thickness and morphology of coatings were...

Finger printing of medieval investment cast idols by radiography

International Nuclear Information System (INIS)

Venkatraman, B.; Babu Rao, C.; Bhattacharya, D.K.; Raj, Baldev

1993-01-01

Among the various methods, radiography is an important technique that can be used to fingerprint an idol. This is because, these idols are cast structures, and radiography is the most reliable technique for the detection of internal features like casting defects. This paper presents the radiographic methodology adopted and the results of the studies to characterise radiographically three medieval cast idols belonging to different periods 9th, 13th, and 16th century obtained from the government museum Madras. (author). 2 refs., 1 fig., 2 tabs

Technique and value of three dimensional reconstruction of stones in the renal pelvis using spiral CT

International Nuclear Information System (INIS)

Fink, B.K.; Fink, U.; Pentenrieder, M.; Kohz, P.; Englmeier, H.K.; Schmeller, N.

1994-01-01

5 patients with staghorn calculi in the renal pelvis were examined by spiral CT. From the raw data three dimensional reconstructions of the stones were obtained. In all patients it was possible to compare the three dimensional model with the stone following performance of percutaneous lithopaxy and endoscopic removal of the fragments. In all cases the three dimensional reconstruction provided a realistic image of the stones and was of practical value for the urologist for preoperative diagnosis and intraoperative control. (orig.) [de

Thermoluminescence of pyramid stones

International Nuclear Information System (INIS)

Gomaa, M.A.; Eid, A.M.

1982-01-01

It is the aim of the present study to investigate some thermoluminescence properties of pyramid stones. Using a few grammes of pyramid stones from Pyramids I and II, the TL glow peaks were observed at 250 and 310 0 C, respectively. The TL glow peaks of samples annealed at 600 0 C, then exposed to 60 Co γ-rays were observed at 120, 190 and 310 0 C, respectively. The accumulated dose of natural samples is estimated to be around 310 Gray (31 krad). By assuming an annual dose is 1 mGy, the estimated age of pyramid stones is 0.31 M year. (author)

Thermoluminescence of pyramid stones

Energy Technology Data Exchange (ETDEWEB)

Gomaa, M A; Eid, A M [Atomic Energy Establishment, Cairo (Egypt)

1982-01-01

It is the aim of the present study to investigate some thermoluminescence properties of pyramid stones. Using a few grammes of pyramid stones from Pyramids I and II, the TL glow peaks were observed at 250 and 310/sup 0/C, respectively. The TL glow peaks of samples annealed at 600/sup 0/C, then exposed to /sup 60/Co ..gamma..-rays were observed at 120, 190 and 310/sup 0/C, respectively. The accumulated dose of natural samples is estimated to be around 310 Gray (31 krad). By assuming an annual dose is 1 mGy, the estimated age of pyramid stones is 0.31 M year.

Algorithm for definition of stones components at kidney-stones illness using two-energetic digital roentgen-graphic method

International Nuclear Information System (INIS)

Nedavnij, O.I.; Osipov, S.P.

2001-01-01

Paper presents the algorithm for definition of stone composition in case of kidney-stones using two-energy digital X-ray photography. One calculated the values of p information parameter for the main types of stones within 40-150 keV energy range. It was shown that p parameter dependence on energy was not essential one (maximum 3.5% deviation), p value for various chemical compositions of kidney stones ranged from 15% (calcium phosphate and calcium oxalate) up to 70% (calcium lactate and calcium oxalate). The conducted studies enable to make a conclusion about the possibility to define material representing the heart of kidney stones using two-energy digital X-ray photography. Paper includes recommendations on selection of the optimal energy values [ru

Determining casting defects in near-net shape casting aluminum parts by computed tomography

Science.gov (United States)

Li, Jiehua; Oberdorfer, Bernd; Habe, Daniel; Schumacher, Peter

2018-03-01

Three types of near-net shape casting aluminum parts were investigated by computed tomography to determine casting defects and evaluate quality. The first, second, and third parts were produced by low-pressure die casting (Al-12Si-0.8Cu-0.5Fe-0.9Mg-0.7Ni-0.2Zn alloy), die casting (A356, Al-7Si-0.3Mg), and semi-solid casting (A356, Al-7Si-0.3Mg), respectively. Unlike die casting (second part), low-pressure die casting (first part) significantly reduced the formation of casting defects (i.e., porosity) due to its smooth filling and solidification under pressure. No significant casting defect was observed in the third part, and this absence of defects indicates that semi-solid casting could produce high-quality near-net shape casting aluminum parts. Moreover, casting defects were mostly distributed along the eutectic grain boundaries. This finding reveals that refinement of eutectic grains is necessary to optimize the distribution of casting defects and reduce their size. This investigation demonstrated that computed tomography is an efficient method to determine casting defects in near-net shape casting aluminum parts.

Influence of Pelvicaliceal Anatomy on Stone Clearance After Flexible Ureteroscopy and Holmium Laser Lithotripsy for Large Renal Stones.

Science.gov (United States)

Inoue, Takaaki; Murota, Takashi; Okada, Shinsuke; Hamamoto, Shuzo; Muguruma, Kouei; Kinoshita, Hidefumi; Matsuda, Tadashi

2015-09-01

This study was performed to evaluate the impact of pelvicaliceal anatomy on stone clearance in patients with remnant fragments in the lower pole after flexible ureteroscopy and holmium laser lithotripsy (fURSL) for renal stones >15 mm. This retrospective study included 67 patients with radiopaque residual fragments (>2 mm) in the lower pole after fURSL for large renal stones (>15 mm). The preoperative infundibular length (IL), infundibular width (IW), infundibulopelvic angle (IPA), and caliceal pelvic height (CPH) were measured using intravenous urography. Multivariate analysis was performed to determine whether any of these measurements affected stone clearance. Of the 67 patients, 55 (82.1%) were stone free (SF) 3 months after fURSL. The anatomic factors significantly favorable for an SF status were a short IL, broad IW, wide IPA, and low CPH. On multivariate analysis, the IPA had a significant influence on an SF status after fURSL (p=0.010). An IPA renal stones according to our multivariate analysis. Additional studies are required to further evaluate the characteristics of the pelvicaliceal anatomy influencing stone clearance.

Development Program for Natural Aging Aluminum Casting Alloys

Energy Technology Data Exchange (ETDEWEB)

Dr. Geoffrey K. Sigworth

2004-05-14

A number of 7xx aluminum casting alloys are based on the ternary Al-Zn-Mg system. These alloys age naturally to high strength at room temperature. A high temperature solution and aging treatment is not required. Consequently, these alloys have the potential to deliver properties nearly equivalent to conventional A356-T6 (Al-Si-Mg) castings, with a significant cost saving. An energy savings is also possible. In spite of these advantages, the 7xx casting alloys are seldom used, primarily because of their reputation for poor castibility. This paper describes the results obtained in a DOE-funded research study of these alloys, which is part of the DOE-OIT ''Cast Metals Industries of the Future'' Program. Suggestions for possible commercial use are also given.

Intrarenal Surgery vs Percutaneous Nephrolithotomy in the Management of Lower Pole Stones Greater than 2 cm.

Science.gov (United States)

Koyuncu, Hakan; Yencilek, Faruk; Kalkan, Mehmet; Bastug, Yavuz; Yencilek, Esin; Ozdemir, Ahmet Tunc

2015-01-01

To compare the efficacy of RIRS and PNL in lower pole stones ≥ 2 cm. Materials and and Methods: A total of 109 patients who underwent PNL or RIRS for solitary lower pole stone between April 2009 and December 2012, were retrospectively analyzed. Lower pole stone was diagnosed with CT scan. Stone size was assessed as the longest axis of the stone. All patients were informed about the advantages, disadvantages and probable complications of both PNL and RIRS before the selection of the procedure. Patients decided the surgery type by themselves without being under any influences and written informed consent was obtained from all patients prior to the surgery. Patients were divided into two groups according to the patients' preference of surgery type. Group 1 consisted of 77 patients who underwent PNL and Group 2 consisted of 32 patients treated with RIRS. Stone free statuses, postoperative complications, operative time and hospitalization time were compared in both groups. There was no statistical significance between the two groups in mean age, stone size, stone laterality, mean follow-up periods and mean operative times. In PNL group, stone-free rate was 96.1% at first session and 100% after the additional procedure. In Group 2, stone-free rate was 90.6% at the first procedure and 100% after the additional procedure. The final stone-free rates and operative times were similar in both groups. RIRS should be an effective treatment alternative to PNL in lower pole stones larger than 2 cm, especially in selected patients.

Intrarenal Surgery vs Percutaneous Nephrolithotomy in the Management of Lower Pole Stones Greater than 2 cm

Directory of Open Access Journals (Sweden)

Hakan Koyuncu

2015-04-01

Full Text Available Purpose To compare the efficacy of RIRS and PNL in lower pole stones ≥2 cm. Materials and and Methods: A total of 109 patients who underwent PNL or RIRS for solitary lower pole stone between April 2009 and December 2012, were retrospectively analyzed. Lower pole stone was diagnosed with CT scan. Stone size was assessed as the longest axis of the stone. All patients were informed about the advantages, disadvantages and probable complications of both PNL and RIRS before the selection of the procedure. Patients decided the surgery type by themselves without being under any influences and written informed consent was obtained from all patients prior to the surgery. Patients were divided into two groups according to the patients’ preference of surgery type. Group 1 consisted of 77 patients who underwent PNL and Group 2 consisted of 32 patients treated with RIRS. Stone free statuses, postoperative complications, operative time and hospitalization time were compared in both groups. Results There was no statistical significance between the two groups in mean age, stone size, stone laterality, mean follow-up periods and mean operative times. In PNL group, stone-free rate was 96.1% at first session and 100% after the additional procedure. In Group 2, stone-free rate was 90.6% at the first procedure and 100% after the additional procedure. The final stone-free rates and operative times were similar in both groups. Conclusions RIRS should be an effective treatment alternative to PNL in lower pole stones larger than 2 cm, especially in selected patients.

Pressing Speed, Specific Pressure and Mechanical Properties of Aluminium Cast

Directory of Open Access Journals (Sweden)

Gaspar S.

2016-06-01

Full Text Available Recent research in the process of aluminum alloy die castings production, which is nowadays deeply implemented into the rapidly growing automobile, shipping and aircraft industries, is aimed at increasing the useful qualitative properties of the die casting in order to obtain its high mechanical properties at acceptable economic cost. Problem of technological factors of high pressure die casting has been a subject of worldwide research (EU, US, Japan, etc.. The final performance properties of die castings are subjected to a large number of technological factors. The main technological factors of high pressure die casting are as follows: plunger pressing speed, specific (increase pressure, mold temperature as well as alloy temperature. The contribution discusses the impact of the plunger pressing speed and specific (increase pressure on the mechanical properties of the casting aluminum alloy.

The Hunger Stones: a new source for more objective identification of historical droughts

Science.gov (United States)

Elleder, Libor

2016-04-01

Extreme droughts recorded recently more frequently in different parts of the world represent the most serious environmental problem. Our contribution identifies periods of hydrological drought. The extreme drought period in summer 2015 enabled the levelling of historical watermarks on the „Hunger Stone" (Hungerstein) in the Elbe in Czech town of Děčín. The comparison of the obtained levels of earlier palaeographic records with systematic measurements in the Děčín profile confirmed the hypothesis that the old watermarks represent the minimal water levels. Moreover, we present a review of so far known Hunger Stones in the Elbe River with their low-level watermarks. For identification of the drought period duration we used the oldest water level records from the Czech Hydrometeorological Institute (CHMI) database archive: Magdeburg (since 1727), Dresden (since 1801), Prague (since 1825) and Decin (since 1851) time-series. We obtained more objective and complex information on all historical droughts between 1727 and 2015. The low water-marks on Hunger Stones give us a possibility for augmentation of systematic records and extended our knowledge's back to 1616. The Hunger Stones in the Elbe River with old watermarks are unique testimony for studying of hydrological extremes, and last but not least also of anthropogenic changes in the riverbed of the Elbe.

A Boy with a Large Bladder Stone

Directory of Open Access Journals (Sweden)

Kuo-Shen Chow

2008-08-01

Full Text Available Despite the frequent association of urinary tract infection with vesicoureteral reflux and urinary calculi, since vesicouretal reflux is induced by bladder stones, the coexistence of vesicoureteral reflux and bladder stones is rare. Because of its occurrence in children belonging to poor socioeconomic groups, it is believed to be a deficiency disorder. Most cases of bladder stones occur between the ages of 2 and 5 years. Common clinical presentations of bladder stones include urinary dribbling and enuresis, frequency of micturition, pain during micturition, pelvic pain and hematuria. We report the occurrence of a large bladder stone in a boy, who experienced intermittent lower abdominal pain and urinary incontinence, both during the day and at night. He had been diagnosed with enuresis and treated in pediatric clinics for 1 year. Delayed diagnosis resulted in bladder stone formation. The stone was larger than 2.5 cm and open vesicolithotomy was therefore selected as the best and safest treatment choice. His symptoms disappeared after surgery. Thorough metabolic and environmental evaluations of such cases are required on an individual basis. Bladder stones should be considered as a possible diagnosis in children presenting with urinary incontinence.

Percutaneous nephrolithotomy for the treatment of radiolucent renal stones in children: is it different opaque stone treatment?

Science.gov (United States)

Adanur, Şenol; Ziypak, Tevfik; Sancaktutar, Ahmet Ali; Tepeler, Abdülkadir; Reşorlu, Berkan; Söylemez, Haluk; Dağgülli, Mansur; Özbey, İsa; Unsal, Ali

2014-02-01

We aimed to evaluate the effectiveness of percutaneous nephrolithotomy (PNL), stone-free rates, and related complications in children with radiolucent renal stones. A total of 56 patients aged auxillary treatment method was detected as 94.6%. The total complication rate was 19.6% (11 patients). No adjacent organ injury was observed. All of the complications that occurred were minor according to the Clavien classification (Clavien Grades I-II). PNL can be applied to radiolucent pediatric renal stones in children with similar success, and complication rates as noted for radiopaque stones.

Female stone disease: the changing trend.

Science.gov (United States)

Marickar, Y M Fazil; Vijay, Adarsh

2009-12-01

This paper has attempted to assess the changes noted in the trends in the incidence and biochemical pattern of female urolithiasis patients during the period 1971-2008. A prospective descriptive clinical study was done on 8,590 stone patients belonging to both sexes treated at the urinary stone clinic. The incidence of stone disease among the two sexes was plotted. The various metabolic parameters including 24-h urine volume, urine calcium, phosphorus, uric acid, oxalate, magnesium, creatinine and citrate, serum creatinine, calcium, phosphorus, uric acid and magnesium and calculated parameter calcium:magnesium ratio were studied. The possible causes for the change in incidence of stone disease in the female sex were elucidated. Of the patients studied, 12.7% (1,091) were females. There was a definite increase in the incidence of female urolithiasis over the past 37 years (P stone genesis, together with the increased excretion of calcium and oxalate may have contributed to the increasing incidence of stone disease in females. This might be due to changes in living standards and dietary habits.

INFLUENCE OF ANNEALING ON HARDNESS OF Cr-Mn-Ni CAST IRONS

Directory of Open Access Journals (Sweden)

V. V. Netrebko

2015-01-01

Full Text Available The necessary level of material’s hardness is determined by the exploitation conditions and presence of technological operations during manufacturing of articles. Mechanical edge cutting machining of wear resistant materials is impeded because of their high hardness. It is recommended to apply annealing in order to decrease hardness and improve machinability. The purpose of the work consisted in obtaining of regression dependences of cast iron’s macrohardness on its chemical content after annealing at 730 °С. With the use of mathematical experimental design the regression dependences of cast iron’s macrohardness and structural components’ microhardness on С, Cr, Mn, Ni content have been established. The minimal hardness of 27,6 HRC after annealing at 730 °С is obtained in the cast iron containing: 3,9% С; 11,4% Cr; 0,6% Mn; 0,2% Ni. The maximal hardness of 70,4 HRC is obtained when the content is as follows: 1,1% С; 25,6% Cr; 5,4% Mn; 3,0% Ni. Annealing at 730 °С decreases the cast irons’ hardness containing the minimal amount of Cr, Mn and Ni. Annealing at 730 °С is recommended for cast irons alloyed by Mn and Ni for increasing of hardness.

Hot forging of roll-cast high aluminum content magnesium alloys

Science.gov (United States)

Kishi, Tomohiro; Watari, Hisaki; Suzuki, Mayumi; Haga, Toshio

2017-10-01

This paper reports on hot forging of high aluminum content magnesium alloy sheets manufactured using horizontal twin-roll casting. AZ111 and AZ131 were applied for twin-roll casting, and a hot-forging test was performed to manufacture high-strength magnesium alloy components economically. For twin-roll casting, the casting conditions of a thick sheet for hot forging were investigated. It was found that twin-roll casting of a 10mm-thick magnesium alloy sheet was possible at a roll speed of 2.5m/min. The grain size of the cast strip was 50 to 70µm. In the hot-forging test, blank material was obtained from as-cast strip. A servo press machine with a servo die cushion was used to investigate appropriate forging conditions (e.g., temperature, forging load, and back pressure) for twin-roll casts (TRCs) AZ111 and AZ131. It was determined that high aluminum content magnesium alloy sheets manufactured using twin-roll casting could be forged with a forging load of 150t and a back pressure of 3t at 420 to 430°C. Applying back pressure during hot forging effectively forged a pin-shaped product.

Investigation of friction and wear characteristics of cast iron material under various conditions

Energy Technology Data Exchange (ETDEWEB)

Joo, Ji Hoon; Kim, Chang Lae; Oh, Jeong Taek; Kim, Dae Eun [Yonsei University, Seoul (Korea, Republic of); Nemati, Narguess [School of Materials and Metallurgy, University of Tehran, Tehran (Iran, Islamic Republic of)

2015-08-15

Cast iron is widely used in fields such as the transport and heavy industries. For parts where contact damage is expected to occur, it is necessary to understand the friction and wear characteristics of cast iron. In this study, we use cast iron plates as the specimens to investigate their friction and wear characteristics. We perform various experiments using a reciprocating type tribotester. We assess the frictional characteristics by analyzing the friction coefficient values that were obtained during the sliding tests. We observe the wear surfaces of cast iron and steel balls using a scanning electron microscope, confocal microscope, and 3D profiler. We investigate the friction and wear characteristics of cast iron by injecting sand and alumina particles having various sizes. Furthermore, we estimate the effect of temperature on the friction and wear characteristics. The results obtained are expected to aid in the understanding of the tribological characteristics of cast iron in industry.

Pattern of family history in stone patients.

Science.gov (United States)

Marickar, Y M Fazil; Salim, Abiya; Vijay, Adarsh

2009-12-01

Genetic predisposition to urolithiasis is a much discussed topic. The objective of this paper is to identify the types of family members of proved urinary stone patients, who have a history of urinary stone formation. The study population consisted of 2,157 urinary stone patients interviewed in 2003-2007 in the urinary stone clinic. Family members with stone history were classified as group 1--first order single (one person in the immediate family-father, mother, siblings, or children), group 2--first order multiple (more than one member in the above group), group 3--second order single (one person in the blood relatives in family--grandparents, grandchildren, uncles, aunts, cousins, etc.) and group 4--second order multiple (more than one member in the above group). Of the 2,157 patients studied, 349 patients gave positive history of stone disease constituting 16.18%. Of these, 321 were males and 28 were females. Subdivision of the family members showed that 282 patients (80.80%) had single family member with stones and the rest 67 (19.20%) had multiple family members with history of stone disease. Group 1 which constituted one family member in the immediate family had 255 involvements (father: 88, mother: 16, brother: 135, sister: 2, son: 10, and daughter: 4); Group 2 with multiple members in the immediate family constituted 51 relatives; of these, father and brother combination was the most common with 35 occurrences. Group 3 with one person in the distant relatives in family namely grandparents, grand children, uncles, aunts, cousins, etc. constituted 27 occurrences and Group 4 with more than one member in the distant family constituted 16 occurrences. It is concluded that single family member involvement was more than multiple involvements. Males predominated. Stone occurrence was more in the immediate family members than distant relatives. Brothers formed the most common group to be involved with stone disease. Study of stone risk in the family members should

Measurement and simulation of deformation and stresses in steel casting

Science.gov (United States)

Galles, D.; Monroe, C. A.; Beckermann, C.

2012-07-01

Experiments are conducted to measure displacements and forces during casting of a steel bar in a sand mold. In some experiments the bar is allowed to contract freely, while in others the bar is manually strained using embedded rods connected to a frame. Solidification and cooling of the experimental castings are simulated using a commercial code, and good agreement between measured and predicted temperatures is obtained. The deformations and stresses in the experiments are simulated using an elasto-viscoplastic finite-element model. The high temperature mechanical properties are estimated from data available in the literature. The mush is modeled using porous metal plasticity theory, where the coherency and coalescence solid fraction are taken into account. Good agreement is obtained between measured and predicted displacements and forces. The results shed considerable light on the modeling of stresses in steel casting and help in developing more accurate models for predicting hot tears and casting distortions.

Measurement and simulation of deformation and stresses in steel casting

International Nuclear Information System (INIS)

Galles, D; Beckermann, C; Monroe, C A

2012-01-01

Experiments are conducted to measure displacements and forces during casting of a steel bar in a sand mold. In some experiments the bar is allowed to contract freely, while in others the bar is manually strained using embedded rods connected to a frame. Solidification and cooling of the experimental castings are simulated using a commercial code, and good agreement between measured and predicted temperatures is obtained. The deformations and stresses in the experiments are simulated using an elasto-viscoplastic finite-element model. The high temperature mechanical properties are estimated from data available in the literature. The mush is modeled using porous metal plasticity theory, where the coherency and coalescence solid fraction are taken into account. Good agreement is obtained between measured and predicted displacements and forces. The results shed considerable light on the modeling of stresses in steel casting and help in developing more accurate models for predicting hot tears and casting distortions.

Successful topical dissolution of cholesterol gallbladder stones using ethyl propionate.

Science.gov (United States)

Hofmann, A F; Amelsberg, A; Esch, O; Schteingart, C D; Lyche, K; Jinich, H; Vansonnenberg, E; D'Agostino, H B

1997-06-01

Topical dissolution of cholesterol gallbladder stones using methyl tert-butyl ether (MTBE) is useful in symptomatic patients judged too ill for surgery. Previous studies showed that ethyl propionate (EP), a C5 ester, dissolves cholesterol gallstones rapidly in vitro, but differs from MTBE in being eliminated so rapidly by the liver that blood levels remain undetectable. Our aim was to test EP as a topical dissolution agent for cholesterol gallbladder stones. Five high-risk patients underwent topical dissolution of gallbladder stones by EP. In three patients, the solvent was instilled via a cholecystostomy tube placed previously to treat acute cholecystitis; in two patients, a percutaneous transhepatic catheter was placed in the gallbladder electively. Gallstone dissolution was assessed by chromatography, by gravimetry, and by catheter cholecystography. Total dissolution of gallstones was obtained in four patients after 6-10 hr of lavage; in the fifth patient, partial gallstone dissolution facilitated basketing of the stones. In two patients, cholesterol dissolution was measured and averaged 30 mg/min. Side effects were limited to one episode of transient hypotension and pain at the infusion site; no patient developed somnolence or nausea. Gallstone elimination was associated with relief of symptoms. EP is an acceptable alternative to MTBE for topical dissolution of cholesterol gallbladder stones in high-risk patients. The lower volatility and rapid hepatic extraction of EP suggest that it may be preferable to MTBE in this investigational procedure.

NWIS Measurements for uranium metal annular castings

International Nuclear Information System (INIS)

Mattingly, J.K.; Valentine, T.E.; Mihalczo, J.T.

1998-01-01

This report describes measurements performed with annular uranium metal castings of different enrichments to investigate the use of 252 Cf-source-driven noise analysis measurements as a means to quantify the amount of special nuclear material (SNM) in the casting. This work in FY 97 was sponsored by the Oak Ridge Y-12 Plant and the DOE Office of Technology Development Programs. Previous measurements and calculational studies have shown that many of the signatures obtained from the source-driven measurement are very sensitive to fissile mass. Measurements were performed to assess the applicability of this method to standard annular uranium metal castings at the Oak Ridge Y-12 plant under verification by the International Atomic Energy Agency (IAEA) using the Nuclear Weapons Identification System (NWIS) processor. Before the measurements with different enrichments, a limited study of source-detector-casting moderator configurations was performed to enhance the correlated information. These configurations consisted of a casting with no reflector and with various thicknesses of polyethylene reflectors up to 10.16 cm in 2.54 cm steps. The polyethylene moderator thickness of 7.62 cm was used for measurements with castings of different enrichments reported here. The sensitivity of the measured parameters to fissile mass was investigated using four castings each with a different enrichment. The high sensitivity of this measurement method to fissile mass and to other material and configurations provides some advantages over existing safeguards methods

Radiographic Co-60 in component of heavy equipment casting

International Nuclear Information System (INIS)

Djoli Soembogo, Harun Al Rasyid R dan Namad Sianta

2016-01-01

The application of radiography using isotope Co-60 source has been used on component of heavy equipment such as component of heavy equipment casting. Components of heavy equipment casting made through metal casting of carbon steel. This study tried applying digital radiography are using isotope Co-60 sources and using scanning positive film media of Epson V700 for digitization results of conventional radiographic films. This radiography is using film AGFA D7 and Fuji 100 to obtain a contrast medium, medium sensitivity and image quality is good. The purpose radiographic Co-60 at a component of heavy equipment casting is detecting indications of the shape and type casting defects of component of heavy equipment casting thus fit for use. Radiographic test of Co-60 has been carried out on component of heavy equipment casting with single wall single image method and the results of radiographic films digitization using scanning positive film media of Epson V700 with observation parameters casting defects. Time exposure of Co-60 radiation was 10 and 15 minutes hours for metal castings of carbon steel for thickness 20.00-50.00 mm by using activity 30.05 Ci and the perpendicular distance to the source of the film is 820 mm. Scanner positive film results in the form of digital radiography which allow for the transfer of digital data or digital computerized data storage. Radiographic test results on component of heavy equipment casting with single wall single image method produce the parameter casting defect of component of heavy equipment casting in position of critical area is found shrinkage that should be repaired and in position of safety area is not found defect indication so casting defect of component of heavy equipment casting are not acceptable according to standards referenced. (author)

Digging up food: excavation stone tool use by wild capuchin monkeys.

Science.gov (United States)

Falótico, Tiago; Siqueira, José O; Ottoni, Eduardo B

2017-07-24

Capuchin monkeys at Serra da Capivara National Park (SCNP) usually forage on the ground for roots and fossorial arthropods, digging primarily with their hands but also using stone tools to loosen the soil and aid the digging process. Here we describe the stone tools used for digging by two groups of capuchins on SCNP. Both groups used tools while digging three main food resources: Thiloa glaucocarpa tubers, Ocotea sp roots, and trapdoor spiders. One explanation for the occurrence of tool use in primates is the "necessity hypothesis", which states that the main function of tool use is to obtain fallback food. We tested for this, but only found a positive correlation between plant food availability and the frequency of stone tools' use. Thus, our data do not support the fallback food hypothesis for the use of tools to access burrowed resources.

Mechanical properties of ductile cast iron and cast steel for intermediate level waste transport containers

International Nuclear Information System (INIS)

Gray, I.L.S.; Sievwright, R.W.T.; Egid, B.; Ajayi, F.; Donelan, P.

1994-01-01

UK Nirex Ltd is developing Type B re-usable shielded transport containers (RSTCs) in a range of shielding thicknesses to transport intermediate level radioactive waste (ILW) to a deep repository. The designs are of an essentially monolithic construction and rely principally on the plastic flow of their material to absorb the energies involved in impact events. Nirex has investigated the feasibility of manufacturing the RSTCs from ductile cast iron (DCI) or cast steel instead of from forgings, since this would bring advantages of reduced manufacturing time and costs. However, cast materials are perceived to lack toughness and ductility and it is necessary to show that sufficient fracture toughness can be obtained to preclude brittle failure modes, particularly at low temperatures. The mechanical testing carried out as part of that programme is described. It shows how the measured properties have been used to demonstrate avoidance of brittle fracture and provide input to computer modelling of the drop tests. (author)

The influence of cooling parameters on the speed of continuous steel casting

Science.gov (United States)

Tirian, G. O.; Gheorghiu, C. A.; Hepuţ, T.; Chioncel, C. P.

2018-01-01

This paper analyzes the cooling parameters of the continuous casting speed. In the researches carried out we aimed to establish some correlation equations between the parameters characterizing the continuous casting process, the temperature of the steel at the entrance to the crystallizer, the superheating of the steel and the flow of the cooling water in the crystallizer and different zones of the secondary cooling. Parallel to these parameters were also the values for the casting speed. The research was made for the casting of round ϕ270mm semi-finished steel products. The steel was developed in an electric EBT furnace with a capacity of 100t, treated in L.F. (Ladle - Furnace) and VD (Vacuum-Degassing) and poured in a 5-wire continuous casting plant. The obtained data was processed in MATLAB using three types of correlation equations. The obtained results are presented both in the analytical and graphical form, each correlation being analyzed from the technological point of view, indicating the optimal values for the independent parameters monitored. In the analysis we present a comparison between the results obtained after the three types of equations for each correlation.

Lioz: The Stone that made Lisbon reborn - A Global Heritage Stone Resource Proposal

Science.gov (United States)

Lopes, Luis

2017-04-01

Lioz: The Stone that made Lisbon reborn - A Global Heritage Stone Resource Proposal Explored since the Roman Period, the Lioz (Cenomanian age microcrystalline fossiliferous limestone) is the main stone used in the buildings and monuments of Lisbon. After the great cataclysm of 1755 (earthquake, tsunami and fire) of 1755, the already known great quality and the near occurrence of these limestones were wisely used in the great reconstruction of the "Capital do Império" (Capital of the Empire). At the time, Lisbon was one of the largest European cities and great business center of the World, so the necessary and urgent reconstruction was not so difficult to start. Sebastião José de Carvalho e Melo, better known as "Marquês de Pombal", Secretary of King José I, successfully took up the challenge of rebuilding Lisbon. Inside the actual Portuguese capital geographical limits, several quarries of the Cretaceous limestone were explored; some still exist and are classified as geomonuments (i.e., Rio Seco Geomonument, 38 ° 42'21 .67''N; 9 ° 11 '30.37''W). As the City boundaries expanded, the quarries stopped and now there is no one asset in Lisbon. The most important exploitation and processing Lioz stone center was situated in Pêro Pinheiro, 20 km NW of Lisbon. Most of the stones used in the National Palace-Convent of Mafra (1717) belongs to the four main types of Lioz (the cream/white "Abancado", the pink/dark pink "Encarnadão", the yellow "Amarelo de Negrais" and the blueish grey "Azulino"), either cut "against" (perpendicular to the bedding plane) or "along" (parallel to the bedding plane). The orientation stone cut deeply controls texture and mechanical properties of the rocks that behaves as different ones were considered. In the last two decades, the Lioz extraction was almost extinguished. However, some of the old quarries was reactivated and produces first quality blocks needed both for new works and restoration of historic buildings and monuments. The

BaTiO3 thick fi lms obtained by tape casting from powders prepared by the oxalate route

Directory of Open Access Journals (Sweden)

Adelina Ianculescu

2009-06-01

Full Text Available BaTiO3 powders were prepared by co-precipitation via oxalate route. The size, morphology and particle size distribution of the oxalate powders have been optimized by the control of different synthesis parameters during the precipitation reaction (nature of salts, concentration of different solutions, aging time. The single phase BaTiO3 oxide particles were obtained after a thermal decomposition of the as-synthesized powders at 850°C for 4 hours under air atmosphere. Oxide powders with a suitable specifi c surface area were selected in order to obtain thick fi lms by the tape casting technique. The microstructure and dielectric properties of the thick films varied obviously depending on the deposition-calcination-sintering cycle used. A double depositioncalcination cycle followed by sintering, as well as a two step deposition-calcination-sintering procedure was used in order to improve the compactness and therefore, the dielectric behaviour. A higher dielectric constant value (~ 750 and lower dielectric losses (~ 2 % were achieved at room temperature and at 1 kHz frequency for the dense, double-deposited fi lm obtained after two deposition-calcination-sintering cycles. For this film, a superior value of the dielectric constant (~ 1100, almost frequency independent in the frequency range of 100 Hz – 10 kHz was gained also at the ferroelectric-paraelectric phase transition temperature of 130°C.

Travelling Through Caste

OpenAIRE

Kumar, Raj

2016-01-01

With its peculiar caste system, India is considered the most stratified of all known societies in human history. This system is ‘peculiar’ as it divides human beings into higher and lower castes and this division is backed by certain religious sanctions based on the sociological concepts of ‘purity’ and ‘pollution’. While the higher caste is associated with ‘purity’, the lower caste is associated with ‘pollution’. The people of the lower castes are not allowed to undertake religious journeys ...

The twelve colourful stones

International Nuclear Information System (INIS)

Doria, R.M.

1983-01-01

A dynamics with twelve colourful stones is created based on the concepts of gauge and colour. It is associated different gauge fields to the same group. A group of gauge invariant Lagrangians is established. A gauge invariant mass term is introduced. The colourful stones physical insight is to be building blocks for quarks and leptons. (Author) [pt

Extracorporeal shock-wave lithotripsy of bile duct stones

International Nuclear Information System (INIS)

Lee, Jong Tae; Kim, Myung Joon; Yoo, Hyung Sik; Suh, Jung Ho; Lee, Moo Sang; Jo, Jang Hwan; Kim, Byung Ro

1989-01-01

During the past one and half year, we performed ESWL therapy in 13 patients with common bile duct and intrahepatic duct stones, applying Lithostar-R (Siemens co. West Germany) and analyzed their results. In 13 patients, 9 residual common bile duct stones and 7 intrahepatic duct stones were selected postoperatively. The size of stones were ranged from 0.7 cm to 3.5 cm in diameter. 2 stones were multiple and the remained 14 were single in number. The visualization of stones were done with fluoroscopy after the injection of contrast media via cholangiographic T-tube or ERCP. ESWL were applied continuously until stone disintegration was visible, or upto maximum number of 3500 discharge of shock wave. If not disintegrated upto 3500, patients were underwent second or third lithotripsy session with interval of one week. Our results showed that among 9 common bile duct stones, 4 were completely disintegrated and passed out spontaneously, but 3 partially fragmented and removed by the additional procedure. 2 were failed. Among 7 intrahepatic stones, 3 completely and 2 partially were succeeded. One stone partially fragmented were retained without removal and other one were failed. Skin petechia in all patients were revealed on the entry port of shock wave, but no serous complication was not occurred

Extracorporeal shock-wave lithotripsy of bile duct stones

Energy Technology Data Exchange (ETDEWEB)

Lee, Jong Tae; Kim, Myung Joon; Yoo, Hyung Sik; Suh, Jung Ho; Lee, Moo Sang; Jo, Jang Hwan; Kim, Byung Ro [Yonsei University College of Medicine, Seoul (Korea, Republic of)

1989-12-15

During the past one and half year, we performed ESWL therapy in 13 patients with common bile duct and intrahepatic duct stones, applying Lithostar-R (Siemens co. West Germany) and analyzed their results. In 13 patients, 9 residual common bile duct stones and 7 intrahepatic duct stones were selected postoperatively. The size of stones were ranged from 0.7 cm to 3.5 cm in diameter. 2 stones were multiple and the remained 14 were single in number. The visualization of stones were done with fluoroscopy after the injection of contrast media via cholangiographic T-tube or ERCP. ESWL were applied continuously until stone disintegration was visible, or upto maximum number of 3500 discharge of shock wave. If not disintegrated upto 3500, patients were underwent second or third lithotripsy session with interval of one week. Our results showed that among 9 common bile duct stones, 4 were completely disintegrated and passed out spontaneously, but 3 partially fragmented and removed by the additional procedure. 2 were failed. Among 7 intrahepatic stones, 3 completely and 2 partially were succeeded. One stone partially fragmented were retained without removal and other one were failed. Skin petechia in all patients were revealed on the entry port of shock wave, but no serous complication was not occurred.

Building stones can be of geoheritage significance

Science.gov (United States)

Brocx, Margaret; Semeniuk, Vic

2017-04-01

Building stones have generally been assigned values according to their cultural, aesthetic, and rarity significance, amongst other criteria, but they also may have geoheritage significance. This is akin to the geoheritage significance ascribed to minerals and fossils housed as ex situ specimens in museums. We proffer the notion that building stones can be of geoheritage value particularly where they comprise permanent buildings, they illustrate significant windows into the history of the Earth, and they can be visited as an ex situ museum locality (e.g., the "Blue Granite" of Iceland) for education as part of building-stone tours. For some rocks the quarries that supplied the building stone are no longer in existence and hence the building stones provide the only record of that type of material; for other rocks, the building stone may illustrate features in the lithology no longer present in the quarry itself (e.g., rare and large xenoliths). Building stones are particularly significant as they are often polished and manifest structures, fabrics, and textures not evident in outcrop. We illustrate here examples of building stone of geoheritage significance using Australian and International examples. Australian designated stones could include the "Sydney Sandstone" or "Victorian Bluestone". For international examples, there is the famous "Carrara Marble" in Italy and the widely known "Portland Limestone" from southern England, the latter having been utilized for St Pauls Cathedral in London and the UN building in New York City.

Study on wear resistance of vanadium alloying compacted/vermicular graphite cast iron

International Nuclear Information System (INIS)

Park, Yoon Woo

1987-01-01

Wear resistance of the Compacted/Vermicular graphite cast irons was studied by changing the vanadium content in the cast irons. The results obtained in this work are summarized as follows. 1. When the same amount of vanadium was added to the flake graphite cast iron, spheroidal graphitecast iron and Compacted/Vermicular graphite cast iron, spheroidal graphite cast iron and Compacted/Vermicular graphite cast iron wear resistance decreased in following sequence, that is, flake graphite cast iron> spheroidal graphite cast iron>Compacted/Vermicular graphite cast iron. 2. Addition of vanadium to the Compacted/Vermicular cast iron leaded to a remarkable increase in hardness because it made the amount of pearlite in matrix increase. 3. Addition of vanadium to the compacted/Vermicular graphite cast iron significantly enhanced wear resistance and the maximum resistance was achieved at about 0.36% vanadium. 4. The maximum amount of wear apppeared at sliding speed of about 1.4m/sec and wear mode was considered to be oxidation abrasion from the observation of wear tracks. (Author)

Caste and power

DEFF Research Database (Denmark)

Roy, Dayabati

2011-01-01

This paper explores the institution of caste and its operation in a micro-level village setting of West Bengal, an Indian state, where state politics at grass roots level is vibrant with functioning local self-government and entrenched political parties. This ethnographic study reveals that caste...... relations and caste identities have overarching dimensions in the day-to-day politics of the study villages. Though caste almost ceases to operate in relation to strict religious strictures, under economic compulsion the division of labour largely coincides with caste division. In the cultural......–ideological field, the concept of caste-hierarchy seems to continue as an influencing factor, even in the operation of leftist politics....

Evaluation of Extracorporeal Shock Wave Lithotripsy (ESWL): Efficacy in Treatment of Urinary System Stones.

Science.gov (United States)

Junuzovic, Dzelaludin; Prstojevic, Jelena Kovacevic; Hasanbegovic, Munira; Lepara, Zahid

2014-10-01

Elimination of stone is determined by size and its localization. Stone from the ureter in 80% of cases can be eliminated spontaneously. If the stone by its characteristics is not spontaneously eliminated, taken are further steps and therapeutic protocols to solve this problem. The study was prospective, open and comparative. It was conducted at the Urology Clinic Clinical Center of Sarajevo University in the period from 2007 to 2013. The study included 404 patients with urinary tract lithiasis treated by ESWL. ESWL treatment is performed on the machine Siemens Model Lithostar Multiline, which has a combined ultrasonographic and fluoroscopic display, large energy density in order to obtain optimum focus (without damaging surrounding tissue) and minimal pain that on rare occasions requires for mild sedation-sedation. From a total of 404 patients included in the study there were 234 (57.92%) male and 170 (42.08%) female patients. The most common type of stone both in female and male patients was calcium type. From a total of 262 calcium stones, 105 of them (40.07%) was present in female patients and 157 (59.92%) in male. Share of infectious type of stone in female patients was 63 (49.60%) and 64 among males (50.39%). Other stones were less abundant in both the gender groups and their total number was only 17. In women their frequency was 2 (13.33%) and 13 among males (86.67%). There was a significant difference in the frequency of different types of stones by gender (x2 = 11.47, p = 0.009). There was no statistically significant correlation between the number of treatments and localization of stones in the ureter, as well as a statistically significant correlation between the size of the stone and the localization of calculus in the ureter.

Using a three-dimensional computer assisted stone volume estimates to evaluate extracorporeal shockwave lithotripsy treatment of kidney stones

DEFF Research Database (Denmark)

Bigum, Lene Hyldgaard; Ulriksen, Peter Sommer; Omar, Omar Salah

2016-01-01

Hospital between April 2013 and January 2014 and follow-up was possible in 77 (95 %) patients. NCCT was used before and after treatment. Treatment response was expressed as a reduction of the stone volume. Stone characteristics as the stone volumes, HU, SSD and localization were measured by radiologist...

Technological Aspects of Low-Alloyed Cast Steel Massive Casting Manufacturing

Directory of Open Access Journals (Sweden)

Szajnara J.

2013-12-01

Full Text Available In the paper authors have undertaken the attempt of explaining the causes of cracks net occurrence on a massive 3-ton cast steel casting with complex geometry. Material used for casting manufacturing was the low-alloyed cast steel with increased wear resistance modified with vanadium and titanium. The studies included the primary and secondary crystallization analysis with use of TDA and the qualitative and quantitative analysis of non-metallic inclusions.

Investment casting of beta titanium alloys for aerospace applications

International Nuclear Information System (INIS)

Wheeler, D.A.; Cianci, M.S.; Vogt, R.G.

1993-01-01

The process of investment casting offers the ability to produce complex titanium components with minimal finish machining, thereby reducing their overall manufacturing cost. While aerospace applications for cast titanium have focused primarily on alpha+beta alloys, recent interest in higher strength beta alloys has prompted an examination of their suitability for investment casting. In this paper, the processing characteristics and mechanical proper-ties of Ti-1 5V-3Cr-3Al-3Sn, Ti-3Al-8V-6Cr-4Mo-4Zr, and Ti-15Mo-3Nb-3Al-0.2Si (wt.%) will be discussed. It will be shown that all three alloy compositions are readily processed using only slight modifications from current Ti-6Al-4V (wt.%) production operations. In addition, the mechanical properties of the cast product form can be manipulated through heat treatment and compare quite favorably with typical properties obtained in wrought beta titanium products. Finally, several demonstration castings are reviewed which illustrate the shape-making capabilities of the investment casting approach for beta titanium alloys

Predictions of outcomes of renal stones after extracorporeal shock wave lithotripsy from stone characteristics determined by unenhanced helical computed tomography: a multivariate analysis

Energy Technology Data Exchange (ETDEWEB)

Wang, Li-Jen; Wong, Yon-Cheong [Chang Gung University, Department of Diagnostic Radiology, Chang Gung Memorial Hospital, Taipei (Taiwan); Chuang, Cheng-Keng; Chu, Sheng-Hsien; Chen, Chih-Shou; Chiang, Yang-Jen [Chang Gung University, Department of Urology, Chang Gung Memorial Hospital, Taipei (Taiwan); See, Lai-Chu [Chang Gung University, Department of Biostatistics Center, Chang Gung Memorial Hospital, Taipei (Taiwan)

2005-11-01

The aim of our study is to analyze the relationships between the characteristics of renal stones determined by unenhanced helical computed tomography (UHCT) and their outcomes after extracorporeal shock wave lithotripsy (ESWL) as well as to predict ESWL outcomes of renal stones by their UHCT characteristics with the use of multivariate analysis. During a 7-month period, 80 adult patients with renal stones underwent ESWL as well as UHCT both before and 3 months after ESWL. Of the 80 patients, 42 patients were classified as ESWL successes and 38 as ESWL failures based on their post-ESWL UHCT findings. For pre-ESWL UHCT, a stone number of more than 2 (P=0.0236), a maximal stone size of greater than 12 mm (P<0.0001), a stone burden of more than 700 mm{sup 3} (P<0.0001), a maximal stone density of more than 900 HU (P=0.0008) and nonround/oval stones (P=0.0007) were associated with ESWL failure outcomes. Multivariate analysis demonstrated that a stone burden of more than 700 mm{sup 3} (P=0.0003), the presence of nonround/oval stones (P=0.0072) and a maximal stone density of more than 900 HU (P=0.0430) were statistically significant predictors of a failure outcome for ESWL. Thus, the analysis of stone characteristics of renal stones by UHCT is helpful in selecting appropriate patients undergoing ESWL for favorable outcomes and reduces the overall costs of the treatment of renal stones. (orig.)

Cover stones on liquefiable soil bed under waves

DEFF Research Database (Denmark)

Sumer, B. Mutlu; Hatipoglu, Figen; Fredsøe, Jørgen

2010-01-01

The paper describes the results of an experimental study on the behavior of cover stones on a liquefiable soil bed exposed to a progressive wave. The soil was silt with d50=0.098mm. Stones, the size of 4cm, were used as cover material. The effect of packing density of stones, and that of number...... of stone layers (including the effect of an intermediate filter layer) were investigated. Pore pressure was measured across the soil depth. The experiments show that the soil liquefaction depended mainly on two parameters: the packing density of stones, and the number of stone layers. When the liquefaction...

Reducing the Incidence of Cast-related Skin Complications in Children Treated With Cast Immobilization.

Science.gov (United States)

Difazio, Rachel L; Harris, Marie; Feldman, Lanna; Mahan, Susan T

2017-12-01

Cast immobilization remains the mainstay of pediatric orthopaedic care, yet little is known about the incidence of cast-related skin complications in children treated with cast immobilization. The purposes of this quality improvement project were to: (1) establish a baseline rate of cast-related skin complications in children treated with cast immobilization, (2) identify trends in children who experienced cast-related skin complications, (3) design an intervention aimed at decreasing the rate of cast-related skin complications, and (4) determine the effectiveness of the intervention. A prospective interrupted time-series design was used to determine the incidence of cast-related skin complications overtime and compare the rates of skin complications before and after an intervention designed to decrease the incidence of cast-related heel complications. All consecutive patients who were treated with cast immobilization from September 2012 to September 2014 were included. A cast-related skin complications data collection tool was used to capture all cast-related skin complications. A high rate of heel events was noted in our preliminary analysis and an intervention was designed to decrease the rate of cast-related skin complications, including the addition of padding during casting and respective provider education. The estimated cast-related skin events rate for all patients was 8.9 per 1000 casts applied. The rate for the total preintervention sample was 13.6 per 1000 casts which decreased to 6.6 in the postintervention sample. When examining the heel-only group, the rate was 17.1 per 1000 lower extremity casts applied in the preintervention group and 6.8 in the postintervention group. Incorporating padding to the heel of lower extremity cast was an effective intervention in decreasing the incidence of cast-related skin complications in patients treated with cast immobilization. Level II.

Extracorporeal shock wave lithotripsy for urinary stones

International Nuclear Information System (INIS)

Shinn, Kyung Sub; Kim, Hyun; Byun, Jae Young; Lee, Myung Hee; Bahk, Yong Whee; Park, Yong Hyun

1988-01-01

Extracorporeal shock wave lithotripsy (ESWL) is a new noninvasive treatment modality for urinary stones, and it sometimes is to necessitate endourologic techniques. ESWL with an Edap lithotripter which uses piezo-electric elements, was performed in 142 cases (130 patients) with urinary stones including 68 in calices, 30 in pelves, and 44 in ureters. Technical factors were 100 storages at 5 to 10 pulse rates/sec and 70-100% adjustable power for about 60 minutes (15-90) for renal stones, and 200 storages at 20 pulse rates/sec and 100% adjustable power for about 60 minutes for ureteral stones in a single treatment under stone localization by 5 MHz ultrasonic sector scanner. All patients were treated at Kangnam St.Mary's Hospital of Catholic University Medical College during the 5 months period from May 1, 1987. Every patient had pre-treatment chest, plain abdomen, intravenous urogram and ultrasonogram studies and post-treatment follow-up abdominal radiograms in 1 to 3 months after ESWL.The overall success rate of ESWL in 142 cases was 94.4%. Eight out of 142 cases were successful. Thus, 134 cases were analysed. Of these, 58 cases (43.3%) received one treatment, 33 cases (24.6%) two treatments, 16 cases (11.9%) three treatments and 27 cases (20.2%) more than four treatments. Renal stones were more successfully treated (98.0%) than ureteral stones (88.1%), and calyceal stones presented the highest success rate (98.5%). The stones as small as 5 to 10 mm in size were easily fragmented and the stones of round of oval shape were more easily pulverized than those of staghorn or amorphous shape. The adjunctive endourlogic techniques such as percutaneous nephrostomy, ureteral catheterization or internal ureteral stenting with a double pigtail catheter were required in 17 cases (11.9%). Complications of ESWL for urolithiasis included hematuria (84.5%), flank pain (8.5%) and fever (5.6%), which were controlled without specific treatment. ESWL using ultrasonic localization was

Extracorporeal shock wave lithotripsy for urinary stones

Energy Technology Data Exchange (ETDEWEB)

Shinn, Kyung Sub; Kim, Hyun; Byun, Jae Young; Lee, Myung Hee; Bahk, Yong Whee; Park, Yong Hyun [Kangnam St. Mary' s Hospital, Catholic University Medical College, Seoul (Korea, Republic of)

1988-06-15

Extracorporeal shock wave lithotripsy (ESWL) is a new noninvasive treatment modality for urinary stones, and it sometimes is to necessitate endourologic techniques. ESWL with an Edap lithotripter which uses piezo-electric elements, was performed in 142 cases (130 patients) with urinary stones including 68 in calices, 30 in pelves, and 44 in ureters. Technical factors were 100 storages at 5 to 10 pulse rates/sec and 70-100% adjustable power for about 60 minutes (15-90) for renal stones, and 200 storages at 20 pulse rates/sec and 100% adjustable power for about 60 minutes for ureteral stones in a single treatment under stone localization by 5 MHz ultrasonic sector scanner. All patients were treated at Kangnam St.Mary's Hospital of Catholic University Medical College during the 5 months period from May 1, 1987. Every patient had pre-treatment chest, plain abdomen, intravenous urogram and ultrasonogram studies and post-treatment follow-up abdominal radiograms in 1 to 3 months after ESWL.The overall success rate of ESWL in 142 cases was 94.4%. Eight out of 142 cases were successful. Thus, 134 cases were analysed. Of these, 58 cases (43.3%) received one treatment, 33 cases (24.6%) two treatments, 16 cases (11.9%) three treatments and 27 cases (20.2%) more than four treatments. Renal stones were more successfully treated (98.0%) than ureteral stones (88.1%), and calyceal stones presented the highest success rate (98.5%). The stones as small as 5 to 10 mm in size were easily fragmented and the stones of round of oval shape were more easily pulverized than those of staghorn or amorphous shape. The adjunctive endourlogic techniques such as percutaneous nephrostomy, ureteral catheterization or internal ureteral stenting with a double pigtail catheter were required in 17 cases (11.9%). Complications of ESWL for urolithiasis included hematuria (84.5%), flank pain (8.5%) and fever (5.6%), which were controlled without specific treatment. ESWL using ultrasonic localization

Factors affecting lower calyceal stone clearance after Extracorporeal ...

African Journals Online (AJOL)

shanker

have been identified [1,3]. These include stone characteristics, the type of lithotripter used, LPC anatomy and body habitus. For iso- lated LPC stones, the pelvicalyceal angle, infundibulum length and width are considered important determinants for stone clearance. The impact of body habitus on stone clearance has so far ...

78 FR 3911 - Big Stone National Wildlife Refuge, Big Stone and Lac Qui Parle Counties, MN; Final Comprehensive...

Science.gov (United States)

2013-01-17

... DEPARTMENT OF THE INTERIOR Fish and Wildlife Service [FWS-R3-R-2012-N259; FXRS1265030000-134-FF03R06000] Big Stone National Wildlife Refuge, Big Stone and Lac Qui Parle Counties, MN; Final Comprehensive... significant impact (FONSI) for the environmental assessment (EA) for Big Stone National Wildlife Refuge...

Emergency management of ureteral stones: Recent advances

Directory of Open Access Journals (Sweden)

Luis Osorio

2008-01-01

Full Text Available Most ureteral stones can be observed with reasonable expectation of uneventful stone passage. When an active ureteral stone treatment is warranted, the best procedure to choose is dependent on several factors, besides stone size and location, including operators′ experience, patients′ preference, available equipment and related costs. Placement of double-J stent or nephrostomy tube represents the classical procedures performed in a renal colic due to acute ureteral obstruction when the conservative drug therapy does not resolve the symptoms. These maneuvers are usually followed by ureteroscopy or extracorporeal shockwave lithotripsy, which currently represent the mainstay of treatment for ureteral stones. In this review paper a literature search was performed to identify reports dealing with emergency management of renal colic due to ureteral stones. The main aspects related to this debated issue are analyzed and the advantages and disadvantages of each treatment option are carefully discussed.

Emergency management of ureteral stones: Recent advances.

Science.gov (United States)

Osorio, Luis; Lima, Estêvão; Autorino, Riccardo; Marcelo, Filinto

2008-10-01

Most ureteral stones can be observed with reasonable expectation of uneventful stone passage. When an active ureteral stone treatment is warranted, the best procedure to choose is dependent on several factors, besides stone size and location, including operators' experience, patients' preference, available equipment and related costs. Placement of double-J stent or nephrostomy tube represents the classical procedures performed in a renal colic due to acute ureteral obstruction when the conservative drug therapy does not resolve the symptoms. These maneuvers are usually followed by ureteroscopy or extracorporeal shockwave lithotripsy, which currently represent the mainstay of treatment for ureteral stones. In this review paper a literature search was performed to identify reports dealing with emergency management of renal colic due to ureteral stones. The main aspects related to this debated issue are analyzed and the advantages and disadvantages of each treatment option are carefully discussed.

Bladder stones after bladder augmentation are not what they seem.

Science.gov (United States)

Szymanski, Konrad M; Misseri, Rosalia; Whittam, Benjamin; Lingeman, James E; Amstutz, Sable; Ring, Joshua D; Kaefer, Martin; Rink, Richard C; Cain, Mark P

2016-04-01

Bladder and renal calculi after bladder augmentation are thought to be primarily infectious, yet few studies have reported stone composition. The primary aim was to assess bladder stone composition after augmentation, and renal stone composition in those with subsequent nephrolithiasis. The exploratory secondary aim was to screen for possible risk factors for developing infectious stones. Patients treated for bladder stones after bladder augmentation at the present institution between 1981 and 2012 were retrospectively reviewed. Data were collected on demographics, surgeries and stone composition. Patients without stone analysis were excluded. Stones containing struvite, carbonate apatite or ammonium acid ureate were classified as infectious. The following variables were analyzed for a possible association with infectious bladder stone composition: gender, history of cloacal exstrophy, ambulatory status, nephrolithiasis, recurrent urea-splitting urinary tract infections, first vs recurrent stones, timing of presentation with a calculus, history of bladder neck procedures, catheterizable channel and vesicoureteral reflux. Fisher's exact test was used for analysis. Of the 107 patients with bladder stones after bladder augmentation, 85 met inclusion criteria. Median age at augmentation was 8.0 years (follow-up 10.8 years). Forty-four patients (51.8%) recurred (14 multiple recurrences, 143 bladder stones). Renal calculi developed in 19 (22.4%) patients with a bladder stone, and 10 (52.6%) recurred (30 renal stones). Overall, 30.8% of bladder stones were non-infectious (Table). Among patients recurring after an infectious bladder stone, 30.4% recurred with a non-infectious one. Among patients recurring after a non-infectious stone, 84.6% recurred with a non-infectious one (P = 0.005). Compared with bladder stones, renal stones were more likely to be non-infectious (60.0%, P = 0.003). Of patients with recurrent renal calculi after an infectious stone, 40.0% recurred with

Consolidation Theory for a Stone Column Composite Foundation under Multistage Loading

Directory of Open Access Journals (Sweden)

Shenggen Huang

2016-01-01

Full Text Available The consolidation theories considering instant load cannot fully reveal the consolidation mechanism of a stone column composite foundation used in the expressway embankments due to the time effect of loading; that is, the expressway embankments are often constructed in several stages for a long time. Meanwhile, owing to the special property that the pile-soil stress ratio is larger than 1, the consolidation theory for sand drain well foundation cannot be used directly in the consolidation analysis of stone column composite foundation. Based on the principle that the vertical load applied on the composite foundation is shared by the stone column and the surrounding soil, the governing solutions for the stone column composite foundation under a multistage load are established. By virtue of the separation of variables, the corresponding solutions of degree of consolidation for loading stage and maintaining load stage are derived separately. According to the Carrillo theorem, the solution for the average total degree of consolidation of entire composite foundation is also obtained. Finally, the reasonableness of the present solution has been verified by comparing the consolidation curve calculated by the present solution with that measured by site test.

Neutron radiography for the characterization of porous structure in degraded building stones

International Nuclear Information System (INIS)

Barone, G; Mazzoleni, P; Raneri, S; Crupi, V; Longo, F; Majolino, D; Venuti, V; Teixeira, J

2014-01-01

As it is well known, the porous structure of stones can change due to different degradation processes that modify the characteristics of freshly quarried blocks. Their knowledge is fundamental for predicting the behavior of stones and the efficacy of conservative treatments. In this context, neutron radiography is a useful tool not only to visualize the structure of porous materials, but also to evaluate the degree of degradation and surface modifications resulting from weathering processes. Furthermore, since thermal neutrons suffer a strong attenuation by hydrogen, this technique is effective in order to investigate the amount of absorbed water in building materials. In the present work, we report a neutron radiography investigation of limestones cropping out in the South-Eastern Sicily and widely used as building stones in Baroque monuments of the Noto Valley. The analyzed samples have been submitted to cyclic salt crystallization that simulate degradation processes acting in exposed stones of buildings. The obtained results demonstrate the interest of neutron radiography to better understand deterioration processes in limestones and to acquire information useful for restoration projects

Metallic Reinforcement of Direct Squeeze Die Casting Aluminum Alloys for Improved Strength and Fracture Resistance

Energy Technology Data Exchange (ETDEWEB)

D. Schwam: J.F. Wallace: Y. Zhu: J.W. Ki

2004-10-01

The utilization of aluminum die casting as enclosures where internal equipment is rotating inside of the casting and could fracture requires a strong housing to restrain the fractured parts. A typical example would be a supercharger. In case of a failure, unless adequately contained, fractured parts could injure people operating the equipment. A number of potential reinforcement materials were investigated. The initial work was conducted in sand molds to create experimental conditions that promote prolonged contact of the reinforcing material with molten aluminum. Bonding of Aluminum bronze, Cast iron, and Ni-resist inserts with various electroplated coatings and surface treatments were analyzed. Also toughening of A354 aluminum cast alloy by steel and stainless steel wire mesh with various conditions was analyzed. A practical approach to reinforcement of die cast aluminum components is to use a reinforcing steel preform. Such performs can be fabricated from steel wire mesh or perforated metal sheet by stamping or deep drawing. A hemispherical, dome shaped casting was selected in this investigation. A deep drawing die was used to fabricate the reinforcing performs. The tendency of aluminum cast enclosures to fracture could be significantly reduced by installing a wire mesh of austenitic stainless steel or a punched austenitic stainless steel sheet within the casting. The use of reinforcements made of austenitic stainless steel wire mesh or punched austenitic stainless steel sheet provided marked improvement in reducing the fragmentation of the casting. The best strengthening was obtained with austenitic stainless steel wire and with a punched stainless steel sheet without annealing this material. Somewhat lower results were obtained with the annealed punched stainless steel sheet. When the annealed 1020 steel wire mesh was used, the results were only slightly improved because of the lower mechanical properties of this unalloyed steel. The lowest results were

Application of the thermal plasma technique in the treatment of stone surfaces

International Nuclear Information System (INIS)

Gonzalez A, Z.I.

2000-01-01

The stone materials which form part of the cultural heritage of Mexico, are degraded under the united action of water, atmospheric gases, air pollution, temperature changes and the microorganisms action; provoking on the stone: fissures, crevices, scalings, fragmentations, pulverizations, etc. Therefore, the purpose of this work is to study the possibilities to apply a protective coating on the stone surfaces, previously clean and consolidated, through the thermal plasma technique. The purpose is to analyse the physical and chemical properties of three types of stone materials: quarry, tezontle and chiluca, usually used in constructions of cultural interest such as: historical monuments, churches, sculptures, etc., before and after to be submitted to the action of thermal plasma in order to examine the feasibility in the use of this coating technique in this type of applications. The application of conventional techniques to determine: porosity, density, absorption, low pressure water absorption and crystallization by total immersion of nuclear techniques such as: neutron activation analysis, x-ray diffraction and scanning electron microscopy as well as of instrumental techniques: optical microscopy, mechanical assays of compression, flexure and surface area calculations, allowed to know the chemical and physical properties of the stone material before and after to be treated through the thermal plasma technique, projecting quartz on the stones surface at different distances and current intensity and showing the effect caused by the modifications or surface alterations present by cause of the application of that coating. the obtained results provide a general panorama of the application of this technique as an alternative to the maintenance of the architectural inheritance built in stone. (Author)

The relationship between serum and urinary Fetuin-A levels and kidney stone formation among kidney stone patients.

Science.gov (United States)

Mehrsai, Abdolrasoul; Guitynavard, Fateme; Nikoobakht, Mohammad Reza; Gooran, Shahram; Ahmadi, Ayat

2017-01-01

Mineralization inhibitors are required to prevent the precipitation of minerals and inhibit the formation of kidney stones and other ectopic calcifications. In laboratory studies, Fetuin-A as a glycoprotein has inhibited hydroxyapatite precipitation in calcium and phosphate supersaturated solutions; however, information about patients with kidney stones is limited. The aim of this study was to investigate the association of serum and urinary Fetuin-A levels with calcium oxalate kidney stones. In this case-control study, 30 patients with kidney stones and 30 healthy individuals without any history of urolithiasis who were referred to the urology ward of Sina Hospital of Tehran, Iran, in 2015 were entered into the study. All patients underwent computerized tomography scans. After collecting demographic information, serum and urine levels of Fetuin-A and some other calcification inhibitors and promoters, were measured and compared using T-test, Mann-Whitney and logistic regression between the two study groups. Patients with kidney stones, on average, had lower levels of Serum Fetuin-A (1522.27 ±755.39 vs. 1914.64 ±733.76 μg/ml; P = 0.046) as well as lower levels of Urine Fetuin-A (944.62 ±188.5 vs. 1409.68 ±295.26 μg/ml; P <0.001). Multivariate logistic analysis showed that urinary calcium and serum creatinine are the risk factors and Fetuin-A is a urinary protective factor for kidney stones. PFC Our study showed that patients with kidney stones had lower serum and urinary levels of Fetuin-A. In the logistic regression model, urinary Fetuin-A was reported as a protective factor for kidney stones.

Market Opportunity of Some Aluminium Silicon Alloys Materials through Changing the Casting Process

Directory of Open Access Journals (Sweden)

Delfim SOARES

2012-08-01

Full Text Available Fatigue is considered to be the most common mechanism by which engineering components fail, and it accounts for at least 90% of all service failures attributed to mechanical causes. Mechanical properties (tensile strength, tensile strain, Young modulus, etc as well as fatigue properties (fatigue life are very dependent on casting method. The most direct effects of casting techniques are on the metallurgical microstructure that bounds the mechanical properties. One of the important variables affected by the casting technique is the cooling rate which is well known to strongly restrict the microstructure. In the present research has been done a comparison of fatigue properties of two aluminum silicon alloys obtained by two casting techniques. It was observed that the fatigue life is increasing with 24% for Al12Si and 31% for AL18Si by using centrifugal casting process instead of gravity casting. This increasing in fatigue life means that a component tailored from materials obtained by centrifugal casting will stay longer in service. It was made an estimation of the time required to recover the costs of technology in order to use the centrifuge process that will allow to obtain materials with improved properties. The amortization can be achieved by using two different marketing techniques: through the release of the product at the old price and with much longer life of the component which means "same price - longer life", or increasing price, by highlighting new product performance which means "higher price - higher properties".

Effect of binder concentration and blade gap on Yttria stabilized Zirconia tapes obtained by tape casting

Energy Technology Data Exchange (ETDEWEB)

Mena Garcia, J.; Reyes Rojas, A.; Rodriguez Gonzalez, C.A.; Hernandez Paz, J.; Garcia Casillas, P.E.; Enriquez Carrejo, J.L.; Camacho Montes, H.

2016-07-01

The tape casting method has kept its interest over the years due to the wide spectrum of its applications and its economic viability in comparison to other techniques focused on micrometric thin films. Two key parameters for tape casting are the binder relative amount and the Dr. Blade gap. The binder relative amount has a strong influence on the rheological properties for the ceramic YSZ slurry (ethanol, butanone, TEA, PVB, PEG, DEP). The coefficient K and the exponent m of the Cross model are reported to be inside the ranges 152.25-231.12 and 0.00987-0.26646 for PVB binder weight percentage concentrations between 6% and 12%. It is possible to describe the ceramic tape thickness dependence by means of a linear relation depending on the Dr. Blade gap whose linear coefficients (slope) are equal to 0.0350 and 0.2171 for green and sintered tapes respectively, with the YSZ slurry of the present work. (Author)

Can ureteral stones cause pain without causing hydronephrosis?

Science.gov (United States)

Song, Yan; Hernandez, Natalia; Gee, Michael S; Noble, Vicki E; Eisner, Brian H

2016-09-01

While computerized tomography (CT) is the gold standard for diagnosis of ureterolithiasis, ultrasound is a less costly and radiation-free alternative which is commonly used to evaluate patients with ureteral colic. The purpose of this study was to evaluate the frequency with which patients with ureteral stones and renal colic demonstrate hydronephrosis in order to better understand the evaluation of these patients. Two hundred and forty-eight consecutive patients presenting with ureteral colic and diagnosed with a single unilateral ureteral stone on CT scan in an urban tertiary care emergency department were retrospectively reviewed. Radiology reports were reviewed for stone size, diagnosis, and degree of hydronephrosis. Of the 248 patients evaluated for suspected ureteral stone, 221 (89.1 %) demonstrated any hydronephrosis, while 27 (10.9 %) did not. Hydronephrosis grade, available in 194 patients, was as follows: mild-70.6 %, moderate-27.8 %, and severe-1.5 %. Mean patient age was 47.0 years (SD 15.5), gender distribution was 35.9 % female and 64.1 % male, and mean stone axial diameter was 4.1 mm (SD 2.4). Stone location was as follows: ureteropelvic junction-4.1 %, proximal ureter-21 %, distal ureter-24.9 %, and ureterovesical junction-47.1 %. Axial stone diameter and coronal length (craniocaudal) were both significant predictors of degree of hydronephrosis (ANOVA, p hydronephrosis. In patients with ureteral stones and colic, nearly 11 % do not demonstrate any hydronephrosis and a majority (nearly 71 %) will demonstrate only mild hydronephrosis. Stone diameter appears to be related to degree of hydronephrosis, whereas age, gender, and stone location are not. The lower incidence of hydronephrosis for small stones causing renal colic may explain the lower diagnostic accuracy of ultrasound when compared to CT for detecting ureteral stones.

Protecting of Marble Stone Facades of Historic Buildings Using Multifunctional TiO2 Nanocoatings

Directory of Open Access Journals (Sweden)

Mohammad A. Aldoasri

2017-11-01

Full Text Available Stone surfaces and façades of historic buildings, due to their predominately outdoor location, suffer from many deterioration factors, including air pollution, soluble salts, relative humidity (RH/temperature, and biodeterioration, which are the main causes of decay. In particular, the façades of the buildings deteriorate with direct exposure to these factors; deformation and disfiguration of superficial decoration and formation of black crusts are often observed on the stones. The development and application of self-cleaning and protection treatments on historical and architectural stone surfaces could be a significant improvement in the conservation, protection and maintenance of Cultural Heritage. A titanium dioxide nanoparticle has become a promising photocatalytic material, owing to its ability to catalyze the complete degradation of many organic contaminants and environmental factors. In this study, TiO2 nanoparticles, dispersed in an aqueous colloidal suspension, were applied directly to historic marble stone surfaces, by spray-coating, in order to obtain a nanometric film over the stone surface. The study started with an investigation of some properties of TiO2 nanoparticles, to assess the feasibility of the use of TiO2 on historic stone and architectural surfaces. Scanning electron microscopy (SEM was, coupled with energy dispersive X-ray (EDX microanalysis, (SEM-EDX, in order to obtain information on coating homogeneity and surface morphology, before and after artificial aging; the activity of the coated surface was evaluated through UV-light exposure, to evaluate photo-induced effects. The changes of molecular structure occurring in treated samples were spectroscopically studied by attenuated total reflection infrared spectroscopy (ATR-FTIR; activity of the hydrophobic property of the coated surface was evaluated by Sterio microscopy, model Zeiss 2010 from Munich, Germany, equipped with photo camera S23 under 80X magnification. The

Wearing Quality of Austenitic, Duplex Cast Steel, Gray and Spheroidal Graphite Iron

Directory of Open Access Journals (Sweden)

S. Pietrowski

2012-04-01

Full Text Available The current work presents the research results of abrasion wear and adhesive wear at rubbing and liquid friction of new austenitic, austenitic-ferritic (“duplex” cast steel and gray cast iron EN-GJL-250, spheroidal graphite iron EN-GJS-600-3, pearlitic with ledeburitic carbides and spheroidal graphite iron with ledeburitic carbides with a microstructure of the metal matrix: pearlitic, upper bainite, mixture of upper and lower bainite, martensitic with austenite, pearlitic-martensitic-bainitic-ausferritic obtained in the raw state. The wearing quality test was carried out on a specially designed and made bench. Resistance to abrasion wear was tested using sand paper P40. Resistance to adhesive wear was tested in interaction with steel C55 normalized, hardened and sulfonitrided. The liquid friction was obtained using CASTROL oil. It was stated that austenitic cast steel and “duplex” are characterized by a similar value of abrasion wear and adhesive wear at rubbing friction. The smallest decrease in mass was shown by the cast steel in interaction with the sulfonitrided steel C55. Austenitic cast steel and “duplex��� in different combinations of friction pairs have a higher wear quality than gray cast iron EN-GJL- 250 and spheroidal graphite iron EN-GJS-600-3. Austenitic cast steel and “duplex” are characterized by a lower wearing quality than the spheroidal graphite iron with bainitic-martensitic microstructure. In the adhesive wear test using CASTROL oil the tested cast steels and cast irons showed a small mass decrease within the range of 1÷2 mg.

Casting defects and fatigue behaviour of ductile cast iron for wind turbine components: A comprehensive study

Energy Technology Data Exchange (ETDEWEB)

Haerkegaard, G. [Norwegian University of Science and Technology, Dept. of Engineering Design and Materials, Trondheim (Norway); Shirani, M.

2011-12-15

Two types of EN-GJS-400-18-LT ductile cast iron were investigated in this research, clean baseline material in the shape of castings with different thicknesses and also defective material from a rejected wind turbine hub. P-S-N curves for baseline EN-GJS-400-18-LT specimens with different dimensions and from castings with different thicknesses at different load ratios were established. Geometrical size effect, technological size effects and mean stress effect on fatigue strength of baseline EN-GJS-400-18-LT were evaluated. Fatigue strength of baseline EN-GJS-400-18-LT was compared with that of defective material from the rejected hub. The effect of defects type, shape, size and position on fatigue strength of this material was evaluated. The hypothesis that the endurance observed in an S-N test can be predicted based on the analysis of crack growth from casting defects through defect-free 'base' material was tested for the analyzed defective material. 3D X-ray computed tomography was use to detect defects in defective specimens and find the defect size distribution. The obtained defect size distribution for the defective material was used in random defect analysis to establish the scatter of fatigue life for defective specimens. Finally both safe-life design and damage tolerant design of wind turbine castings were analyzed and compared. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Use of Local Stone: Successes, Failures and Considerations

Science.gov (United States)

Gerns, Edward; Will, Rachel

2015-04-01

Stone has been used in construction for thousands of years. Until relatively recently, local stone was used almost exclusively due to limited transportation options and to reduce costs. . Historically, the stone was often taken from nearby fields, known as fieldstone, without any specific quarrying operations and used to create unique assemblages of vernacular buildings. Stone, perhaps more than any other natural building material, has numerous varieties and characteristics within the broader classifications of stone: sedimentary, igneous and metamorphic. In exterior applications, stone historically has been used for foundations, localized cladding elements and in some instances entire building facades. Many of these local stones are appropriate for foundations, but not necessarily for cladding systems, particularly once the stone was quarried and modified rather than used in its natural form. These issues tended to be less significant in historic buildings when wall systems were much thicker and had more redundancies in the cladding systems Since around 1880, the use of these thinner applications of quarried stones as more traditional cladding systems (rather than cladding and structure) has resulted in challenges including unanticipated weathering characteristics, residual stresses and detrimental inclusions. These conditions can result in expensive and extensive repairs and maintenance. Often the options to address these characteristics are limited or potentially drastic depending on the scale of installation. It is important to understand the cause of the issues, understand if these issues are significant and finally how to address them appropriately. Where and how these unique local stones are installed as well as climate and weathering patterns certainly contribute to the potential unanticipated conditions. This presentation will be divided into two general parts. The first will address various stones used historically throughout regions within the United

Anholt Rosetta Stones

DEFF Research Database (Denmark)

Trempe Jr., Robert B.; Buthke, Jan

2017-01-01

This book records and celebrates the research finding of Anholt Island by students from Studio 2B, Arkitektskolen Aarhus, These mahogany constructions are our architectural versions of a Rosetta Stone. These are constructs that record layers of information about Anholt island through virtual...... and physical techniques, where each step and mechanic imparts and inscribes knowledge beyond the 1:1. These constructs are visual keys, used to inspire and influence all decision-making processes in a design project. These architectural Rosetta Stones document and amplify quantitative information about a site...

Temporally variable macroinvertebrate-stone relationships in streams

DEFF Research Database (Denmark)

Jacobsen, D.

2005-01-01

of fauna parameter and stone variable from different sampling dates (n=9-11) were rarely correlated to any of the measures of stream stability, this study has demonstrated high temporal variability in fauna-stone relationships (CV's of regression slopes). Consequently, temporally un-replicated studies......Stones were used to sample macroinvertebrates and characterise microhabitats at monthly or bimonthly intervals in six Ecuadorian streams covering a gradient in four different stability measures and other stream characteristics. The physical variables current velocity, water depth, horizontal...... of families vs. individuals) were related to the physical characteristics of individual stone habitats. My second objective was to quantify temporal variability in fauna-stone relationships and to analyse if such variability was related to overall stability of stream reaches. Partial Least Squares (PLS...

Instrumental neutron activation analysis of kidney stones

International Nuclear Information System (INIS)

Sarmani, S.; Kuan, L.L.; Bakar, M.A.A.

1990-01-01

Kidney stone samples of the types calcium oxalate, uric acid, and xanthine were analyzed for their elemental contents by neutron activation analysis to study both the elemental correlation and influence of element on stone precipitation processes. Elements, such as Al, Au, Br, Ca, Cl, Co, Cr, Fe,H, I, K, Mg, Na, Sb, Se, Sr, and Zn, were determined quantitatively. Calcium oxalate stones contained higher concentration of all the elements analyzed compared to uric acid or xanthine stones. The concentrations of Cl, Fe, K, Na, Sr, and Zn were relatively higher than Au, Co, Cr, and Sb. A positive correlation exists between Ca and Zn, whereas a negative correlation exists between Sr and Ca. Zinc may play an important role in the formation of calcium oxalate stone

Mapping of mechanical properties of cast iron melts using non-destructive structuroscopy

Directory of Open Access Journals (Sweden)

J. Dočekal

2008-07-01

Full Text Available The contribution is focused on mapping of mechanical properties using methods of non-destructive structuroscopy of cast irons, which are a result of research at TU of Liberec and Institute of Physics of ASCR. Investigated samples become from melts of FOCAM s.r.o Olomouc Foundry shop. It compares data of mechanical properties obtained using ultrasound method with data from magnetic spot method and MAT. These are interpreted by mathematic models applicable in practice. In the following it concerns to derivation of loading tensile curve method, which can be used to obtain yield and fatigue strength limits even for cast irons with flake graphite. In spite of promising results reported by literature the experiments are bothered with error. This method can be applied to structure checking both before casting and at vendor inspection of castings.

[Evaluating the accuracy of three-dimensional reconstruction of the intercuspal position for dentition casts aided by a mechanical appliance].

Science.gov (United States)

Hu, Z W; Li, W W; Zhang, X Y; Fan, B L; Wang, Y; Sun, Y C

2016-08-01

To develop a aided mechanical appliance for rapid reconstruction of three-dimensional(3D)relationship of dentition model after scanning and evaluation of its accuracy. The appliance was designed by forward engineering software and fabricated by a high precision computer numerical control(CNC)system. It contained upper and lower body, magnetic pedestal and three pillars. Nine 3 mm diameter hemispheres were distributed equally on the axial surface of each pedestal. Faro Edge 1.8m was used to directly obtain center of each hemisphere(contact method), defined as known center. A pair of die-stone standard dentition model were fixed in intercuspal position and then fixed on the magnetic pedestals with low expansion ratio plaster. Activity 880 dental scanner was used to scan casts after the plaster was completely set. In Geomagic 2012, the centers of each hemisphere were fitted and defined as scanning centers. Scanning centers were aligned to known centers by reference point system to finish the 3D reconstruction of the intercuspal occlusion for the dentition casts. An observation coordinate system was interactively established. The straight-line distances in the X(coronal), Y(saggital), and Z(vertical)between the remaining 6 pairs of center points derived from contact method and fitting method were measured respectively and analyzed using a paired t-test. The differences of the straight-line distances of the remaining 6 pairs of center points between the two methods were X:(-0.05±0.10)mm, Y:(0.02±0.06)mm, and Z:(0.01 ± 0.05)mm. The results of paired t-test showed no significant differences(P>0.05). The mechanical appliance can help to reconstruct 3D jaw relation by scanning single upper and lower dentition model with usual commercial available dental cast scanning system.

Grasping the Formless in Stones

DEFF Research Database (Denmark)

Aktor, Mikael

2017-01-01

and the repertoire of used forms. The chapter demonstrates that neither anthropomorphic perceptions nor the agency of the stone material alone make up the ritual aesthetics in which the stones are involved. Rather, applying concepts from landscape phenomenology and cognitive theories including the role of material...

New Approaches to Aluminum Integral Foam Production with Casting Methods

Directory of Open Access Journals (Sweden)

Ahmet Güner

2015-08-01

Full Text Available Integral foam has been used in the production of polymer materials for a long time. Metal integral foam casting systems are obtained by transferring and adapting polymer injection technology. Metal integral foam produced by casting has a solid skin at the surface and a foam core. Producing near-net shape reduces production expenses. Insurance companies nowadays want the automotive industry to use metallic foam parts because of their higher impact energy absorption properties. In this paper, manufacturing processes of aluminum integral foam with casting methods will be discussed.

Investigations of excavated clay-stone as backfill/seal material

International Nuclear Information System (INIS)

Zhang, Chun-Liang

2012-01-01

Document available in extended abstract form only. Crushed clay-stone produced by excavation activities of repository drifts has been investigated as backfill/seal material at the GRS laboratory. The raw aggregate with coarse grains is considered to be used for backfilling the repository openings and, in mixture with bentonite, for sealing the boreholes, drifts and shafts. The GRS research programme focused on characterizing the thermo-hydro-mechanical properties of the excavated Callovo-Oxfordian clay-stone (COX) and the clay-stone-bentonite mixtures, including mechanical compaction, gas and water permeability as function of porosity, water retention and saturation, swelling capacity, and thermal properties of the materials. The most important results are presented in this paper. Figure 1 shows the compaction and permeability behaviour of the excavated clay-stone with grains up to a size of 32 mm. The results were obtained on large samples of 280 mm diameter and 680 mm height under quasi-hydrostatic compression. The porosity and permeability decrease with increasing load. The porosity-mean stress relation is non-linear and may be expressed by an exponential function. The backfill becomes stiffer at low porosities and can sustain certain deviatoric loads. At porosity of ∼21 %, the strength is characterized by an inherent cohesion of 3.7 MPa and an internal friction angle of 12 deg.. Additionally, the compaction is also dependent on time or loading rate, water content, and temperature. The compaction of the porous backfill material leads to a reduction in permeability. The measured gas permeability decreases much faster at low porosities below ∼25 %. The gas permeability at porosity of ∼20 % becomes as low as that of 10 -20 - 10 -21 m 2 for the intact clay rock. This is probably due to disconnection of the pore network during the compaction. As sealing material, powdered COX clay-stone was mixed with MX80 bentonite powder in different ratios and compacted to

Effect of cast steel production metallurgy on the emergence of casting defects

Directory of Open Access Journals (Sweden)

L. Čamek

2016-10-01

Full Text Available The paper documents metallurgical possibilities of high alloy cast steel production in open induction medium frequency furnaces and an electric arc furnace in a gravity die casting foundry. The observation was focused on the emergence of gas defects in steel castings. The content of gases achieved during the metallurgical processes was evaluated for every unit of the production equipment and the casting ladle before casting into disposable sand moulds. The sand mould area was considered to be constant. The aim was to evaluate the current metallurgical possibilities of affecting the content of gases in high alloy cast steel in the current technical conditions of the foundry.

The surface layer of austempered ductile iron investment castings properties

Directory of Open Access Journals (Sweden)

D. Myszka

2009-01-01

Full Text Available The article presents a unique process of carbonnitriding and nitriding the precision casting surfaces of austempered ductile iron. The results of the research are pointing that adequate process parameters allow to obtain multiple increase of wear resistance and a significant increase of corrosion resistance. Also, changes of cast microstructure and hardness are presented.

SPRAY CASTING

OpenAIRE

SALAMCI, Elmas

2010-01-01

ABSTRACT This paper is designed to provide a basic review of spray casting. A brief overview of the historical development of spray  casting and the description of plant and equipment have been given. Following metallurgical characteristics of spray formed alloys, process parameters and solidification mechanism of spray deposition have been discussed in detail. Finally, microstructure and mechanical properties of the selected spray cast Al-Zn-Mg-Cu alloys have been presented and comp...

Can sonography define the chemical composition of gall stones

International Nuclear Information System (INIS)

Frentzel-Beyme, B.; Faehndrich, R.; Arnan-Thiele, B.

1983-01-01

Eight sonographic patterns caused by gall stones are described. In an attempt to explain these different appearances, 62 stones were analysed chemically and physically. The chemical composition of the stones did not correlate with their sonographic pattern. Cholesterol stones cannot be recognised as such by sonography. The formation of an acoustic shadow depends largely on the position of the stone within the acoustic beam. It therefore follows that the examination must be done by keeping the focal plane of the transducer in proper relationship to the stone. (orig.) [de

"Sydney sandstone": Heritage Stone from Australia

Science.gov (United States)

Cooper, Barry; Kramar, Sabina

2014-05-01

Sydney is Australia's oldest city being founded in 1788. The city was fortunate to be established on an extensive and a relatively undeformed layer of lithified quartz sandstone of Triassic age that has proved to be an ideal building stone. The stone has been long identified by geologists as the Hawkesbury Sandstone. On the other hand the term "Sydney sandstone" has also been widely used over a long period, even to the extent of being utilised as the title of published books, so its formal designation as a heritage stone will immediately formalise this term. The oldest international usage is believed to be its use in the construction of the Stone Store at Kerikeri, New Zealand (1832-1836). In the late 19th century, public buildings such as hospitals, court houses as well as the prominent Sydney Town Hall, Sydney General Post Office, Art Gallery of New South Wales, State Library of New South Wales as well as numerous schools, churches, office building buildings, University, hotels, houses, retaining walls were all constructed using Sydney sandstone. Innumerable sculptures utilising the gold-coloured stone also embellished the city ranging from decorative friezes and capitals on building to significant monuments. Also in the late 19th and early 20th century, Sydney sandstone was used for major construction in most other major Australian cities especially Melbourne, Adelaide and Brisbane to the extent that complaints were expressed that suitable local stone materials were being neglected. Quarrying of Sydney sandstone continues today. In 2000 it was recorded noted that there were 33 significant operating Sydney sandstone quarries including aggregate and dimension stone operations. In addition sandstone continues to be sourced today from construction sites across the city area. Today major dimension stone producers (eg Gosford Quarries) sell Sydney sandstone not only into the Sydney market but also on national and international markets as cladding and paving products

A study on the utilization of stone powder sludge (III)

Energy Technology Data Exchange (ETDEWEB)

Kim, Chi Kwon; Sohn, Jeong Soo; Kim, Byung Gyu [Korea Institute of Geology Mining and Materials, Taejon (Korea, Republic of)

1996-12-01

This study was performed to activate the building stone industry by increasing the recycling amounts of waste resources and minimizing the generation of the environmental pollution materials. In order to utilize the waste stone and stone powder sludge generated from the domestic quarry and cutting process of stone plates, the manufacturing technology of the artificial stone plate as a building material was developed. Based on the first and second year results, this third-year study was performed for manufacturing the large-scale artificial stone plate of 500 x 500 x 20 mm. Also for applying these artificial stone plates to the flooring and interior materials in the building industry, the manufacture of the large-scale artificial stone plates with various patterns and colors was carried out by changing the species and the ratio of raw materials, amounts of binder and molding pressure. Artificial stone plate was composed of waste crushed stone, stone powder sludge and binder which was used for binding waste stone and rock powder each other. In order to investigate the physical properties of large-scale artificial stone, the measure of specific gravity, absorption ratio, P-wave velocity, compressive strength, tensile strength, Young`s modulus, and Poisson`s ratio were carried out. As a result of testing physical properties, there was no difference between small-scale artificial stone and large-scale one. At the optimum conditions it was shown that the properties of artificial stones were as follows, 2.32 of specific gravity, 0.33 of water-absorption ratio, 780 kg/cm{sup 2} of compressive strength and 98 kg/cm{sup 2} of tensile strength. Based on the above results, the preliminary economic estimation on the manufacture of the artificial stone plate was carried out. It was shown that the manufacturing cost of the artificial stone plate was 18,000 won/m{sup 2}, which was merely half that of natural stone plate, and the application of these on the building stone industry

Differentiation of uric acid versus non-uric acid kidney stones in the presence of iodine using dual-energy CT

Science.gov (United States)

Wang, J.; Qu, M.; Leng, S.; McCollough, C. H.

2010-04-01

In this study, the feasibility of differentiating uric acid from non-uric acid kidney stones in the presence of iodinated contrast material was evaluated using dual-energy CT (DECT). Iodine subtraction was accomplished with a commercial three material decomposition algorithm to create a virtual non-contrast (VNC) image set. VNC images were then used to segment stone regions from tissue background. The DE ratio of each stone was calculated using the CT images acquired at two different energies with DECT using the stone map generated from the VNC images. The performance of DE ratio-based stone differentiation was evaluated at five different iodine concentrations (21, 42, 63, 84 and 105 mg/ml). The DE ratio of stones in iodine solution was found larger than those obtained in non-iodine cases. This is mainly caused by the partial volume effect around the boundary between the stone and iodine solution. The overestimation of the DE ratio leads to substantial overlap between different stone types. To address the partial volume effect, an expectation-maximization (EM) approach was implemented to estimate the contribution of iodine and stone within each image pixel in their mixture area. The DE ratio of each stone was corrected to maximally remove the influence of iodine solutions. The separation of uric-acid and non-uric-acid stone was improved in the presence of iodine solution.

The composition of urinary stones in central sindh

International Nuclear Information System (INIS)

Memon, J.M.; Naqvi, S.Q.H.

2014-01-01

To determine chemical analysis of urinary stones of central sindh. Study design: Prospective and randomized study. Setting: Department of Surgery and Pathology of Peoples University of Medical and Health Sciences Nawabshah. Duration of study: Three years from May 2008 to May 2011. Material and Methods: Total 106 urolith patients who underwent open stone surgery were included in the study. EDTA Titration used for determination of calcium ions and determination of oxalate, phosphate, magnesium, ammonia, uric acid and cystine stones was carried out using spectrophotometer. These patients were asked to fill out a proforma with parameters of age, sex, radiological location of stone and chemical composition of surgically recovered stones. The stone analysis findings were reviewed and compared with other reported series Results: In this study 75(70.75%) patients were male and 31 (29.25%) female. Male to female ratio was of 2.41:1. The age ranged from 1 to 70 years with the mean of 22.69 years. The peak incidence of upper urinary tract stone in 20-30 years and lower urinary tract stones in both sexes was under 10 years. Anatomical location of stone showed 48(45.29%) renal, 13(12.26%) ureteric and 45(42.45%) bladder calculi. Chemical analysis revealed 56(52.8%) calcium oxalate, 7(6.6%) calcium phosphate, 11(10.3%) ammonium urate, 18(16.9%) uric acid, 13(12.2%) Sturvite and 1(0.9%) cystine calculi. Conclusion: It was concluded that urolithiasis is predominantly male disease. No age group was spared to stone disease. Calcium oxalate, uric acid, ammonium urate and mixed calculi are the main types in our study due to poor nutritional status, poverty and inadequate health facilities. Considering that knowledge of stone composition is of utmost importance to modify the incidence of urolithiasis. (author)

Ornamental Stones and Gemstones: The limits of heritage stone designation: The case for and against Australian Precious Opal

Science.gov (United States)

Cooper, Barry

2015-04-01

When the international designation of natural stone types was first mooted in 2007, stones that were utilised in building and construction were the primary focus of attention. However following public discussion it soon became apparent that sculptural stones, stone used for utilitarian purposes such as millstones, as well as archaeological materials including stones used by early man could all be positively assessed as a potential Global Heritage Stone Resource (GHSR). Over the past 2 years it has been realised there is also a range of ornamental and semi-precious stones that may also be considered in the same international context. Examples in this respect include Imperial Porphyry sourced from Egypt that was much prized in the ancient world and "Derbyshire Blue John" a variety of fluorspar from central England that was used for vases, chalices, urns, candle sticks, jars, bowls door, jewellery and fire-place surrounds, especially in the 18th and 19th centuries. It is at this point that rock materials, sometimes used as gemstones, impinge on the domain of typical heritage stones. In Australia, the gemstone most identifiable with the country is precious opal formed by sedimentary processes in the Great Artesian Basin. In this paper the question is asked whether "Australian Precious Opal" could be or should be considered as a heritage stone of international significance. Immediately Australian Precious Opal satisfies several GHSR criteria including historic use for more than 50 years and wide-ranging utilisation for prestige jewellery around the world. It is also recognised as a cultural icon including association with national identity in Australia as it is legally defined as Australia's "National Gemstone" as well as being the "Gemstone Emblem" for the State of South Australia. Opal continues to be mined. Designation of Australian Precious Opal as a Global Heritage Stone Resource would likely involve formal international recognition of Australian opal in the

Predictions of outcomes of renal stones after extracorporeal shock wave lithotripsy from stone characteristics determined by unenhanced helical computed tomography: a multivariate analysis

International Nuclear Information System (INIS)

Wang, Li-Jen; Wong, Yon-Cheong; Chuang, Cheng-Keng; Chu, Sheng-Hsien; Chen, Chih-Shou; Chiang, Yang-Jen; See, Lai-Chu

2005-01-01

The aim of our study is to analyze the relationships between the characteristics of renal stones determined by unenhanced helical computed tomography (UHCT) and their outcomes after extracorporeal shock wave lithotripsy (ESWL) as well as to predict ESWL outcomes of renal stones by their UHCT characteristics with the use of multivariate analysis. During a 7-month period, 80 adult patients with renal stones underwent ESWL as well as UHCT both before and 3 months after ESWL. Of the 80 patients, 42 patients were classified as ESWL successes and 38 as ESWL failures based on their post-ESWL UHCT findings. For pre-ESWL UHCT, a stone number of more than 2 (P=0.0236), a maximal stone size of greater than 12 mm (P 3 (P 3 (P=0.0003), the presence of nonround/oval stones (P=0.0072) and a maximal stone density of more than 900 HU (P=0.0430) were statistically significant predictors of a failure outcome for ESWL. Thus, the analysis of stone characteristics of renal stones by UHCT is helpful in selecting appropriate patients undergoing ESWL for favorable outcomes and reduces the overall costs of the treatment of renal stones. (orig.)

Does the casting mode influence microstructure, fracture and properties of different metal ceramic alloys?

Science.gov (United States)

Bauer, José Roberto de Oliveira; Grande, Rosa Helena Miranda; Rodrigues-Filho, Leonardo Eloy; Pinto, Marcelo Mendes; Loguercio, Alessandro Dourado

2012-01-01

The aim of the present study was to evaluate the tensile strength, elongation, microhardness, microstructure and fracture pattern of various metal ceramic alloys cast under different casting conditions. Two Ni-Cr alloys, Co-Cr and Pd-Ag were used. The casting conditions were as follows: electromagnetic induction under argon atmosphere, vacuum, using blowtorch without atmosphere control. For each condition, 16 specimens, each measuring 25 mm long and 2.5 mm in diameter, were obtained. Ultimate tensile strength (UTS) and elongation (EL) tests were performed using a Kratos machine. Vickers Microhardness (VM), fracture mode and microstructure were analyzed by SEM. UTS, EL and VM data were statistically analyzed using ANOVA. For UTS, alloy composition had a direct influence on casting condition of alloys (Wiron 99 and Remanium CD), with higher values shown when cast with Flame/Air (p casting condition" influenced the EL and VM results, generally presenting opposite results, i.e., alloy with high elongation value had lower hardness (Wiron 99), and casting condition with the lowest EL values had the highest VM values (blowtorch). Both factors had significant influence on the properties evaluated, and prosthetic laboratories should select the appropriate casting method for each alloy composition to obtain the desired property.

Do You Have Symptoms of a Kidney Stone?

Science.gov (United States)

... Or, the stone will be removed with treatment. Dogs, Cats, and Kidney Stones Humans aren't the only ones affected by kidney and bladder stones. Dogs, cats, and other animals can also have kidney ...

Characterization of Ni–Cr alloys using different casting techniques and molds

International Nuclear Information System (INIS)

Chen, Wen-Cheng; Teng, Fu-Yuan; Hung, Chun-Cheng

2014-01-01

This study differentiated the mechanical properties of nickel–chromium (Ni–Cr) alloys under various casting techniques (different casting molds and casting atmospheres). These techniques were sampled by a sand mold using a centrifugal machine in ambient air (group I) and electromagnetic induction in an automatic argon castimatic casting machine (group II). The specimen casting used a graphite mold by a castimatic casting machine (group III). The characteristics of the Ni–Cr alloys, yield and ultimate tensile strength, bending modulus, microhardness, diffraction phase, grindability, ability to spring back, as well as ground microstructure and pattern under different casting conditions were evaluated. The group III specimens exhibited the highest values in terms of strength, modulus, hardness, and grindability at a grind rate of 500 rpm. Moreover, group III alloys exhibited smaller grain sizes, higher ability to spring back, and greater ductility than those casted by sand investment (groups I and II). The main factor, “casting mold,” significantly influenced all mechanical properties. The graphite mold casting of the Ni–Cr dental alloys in a controlled atmosphere argon casting system provided an excellent combination of high mechanical properties and good ability to spring back, and preserved the ductile properties for application in Ni–Cr porcelain-fused system. The results can offer recommendations to assist a prosthetic technician in selecting the appropriate casting techniques to obtain the desired alloy properties. - Highlights: • Properties of Ni–Cr alloys using various casting techniques are characterized. • Alloys cast by graphite mold exhibited higher recovery angle and more ductility. • Alloys cast by graphite mold exhibited higher strength and grinding rate. • Alloys in this study increase operative room to adjust the precision for prosthesis

Characterization of Ni–Cr alloys using different casting techniques and molds

Energy Technology Data Exchange (ETDEWEB)

Chen, Wen-Cheng, E-mail: wencchen@fcu.edu.tw [Advanced Medical Devices and Composites Laboratory, Department of Fiber and Composite Materials, College of Engineering, Feng Chia University, Taichung 40724, Taiwan (China); Teng, Fu-Yuan [Department of Dentistry, Kaohsiung Armed Forces General Hospital, Kaohsiung 802, Taiwan (China); School of Dentistry, College of Dental Medicine, Kaohsiung Medical University, Kaohsiung 807, Taiwan (China); Hung, Chun-Cheng [School of Dentistry, College of Dental Medicine, Kaohsiung Medical University, Kaohsiung 807, Taiwan (China); Department of Dentistry, Kaohsiung Medical University Hospital, Kaohsiung 807, Taiwan (China)

2014-02-01

This study differentiated the mechanical properties of nickel–chromium (Ni–Cr) alloys under various casting techniques (different casting molds and casting atmospheres). These techniques were sampled by a sand mold using a centrifugal machine in ambient air (group I) and electromagnetic induction in an automatic argon castimatic casting machine (group II). The specimen casting used a graphite mold by a castimatic casting machine (group III). The characteristics of the Ni–Cr alloys, yield and ultimate tensile strength, bending modulus, microhardness, diffraction phase, grindability, ability to spring back, as well as ground microstructure and pattern under different casting conditions were evaluated. The group III specimens exhibited the highest values in terms of strength, modulus, hardness, and grindability at a grind rate of 500 rpm. Moreover, group III alloys exhibited smaller grain sizes, higher ability to spring back, and greater ductility than those casted by sand investment (groups I and II). The main factor, “casting mold,” significantly influenced all mechanical properties. The graphite mold casting of the Ni–Cr dental alloys in a controlled atmosphere argon casting system provided an excellent combination of high mechanical properties and good ability to spring back, and preserved the ductile properties for application in Ni–Cr porcelain-fused system. The results can offer recommendations to assist a prosthetic technician in selecting the appropriate casting techniques to obtain the desired alloy properties. - Highlights: • Properties of Ni–Cr alloys using various casting techniques are characterized. • Alloys cast by graphite mold exhibited higher recovery angle and more ductility. • Alloys cast by graphite mold exhibited higher strength and grinding rate. • Alloys in this study increase operative room to adjust the precision for prosthesis.

Characterization of Ni-Cr alloys using different casting techniques and molds.

Science.gov (United States)

Chen, Wen-Cheng; Teng, Fu-Yuan; Hung, Chun-Cheng

2014-02-01

This study differentiated the mechanical properties of nickel-chromium (Ni-Cr) alloys under various casting techniques (different casting molds and casting atmospheres). These techniques were sampled by a sand mold using a centrifugal machine in ambient air (group I) and electromagnetic induction in an automatic argon castimatic casting machine (group II). The specimen casting used a graphite mold by a castimatic casting machine (group III). The characteristics of the Ni-Cr alloys, yield and ultimate tensile strength, bending modulus, microhardness, diffraction phase, grindability, ability to spring back, as well as ground microstructure and pattern under different casting conditions were evaluated. The group III specimens exhibited the highest values in terms of strength, modulus, hardness, and grindability at a grind rate of 500 rpm. Moreover, group III alloys exhibited smaller grain sizes, higher ability to spring back, and greater ductility than those casted by sand investment (groups I and II). The main factor, "casting mold," significantly influenced all mechanical properties. The graphite mold casting of the Ni-Cr dental alloys in a controlled atmosphere argon casting system provided an excellent combination of high mechanical properties and good ability to spring back, and preserved the ductile properties for application in Ni-Cr porcelain-fused system. The results can offer recommendations to assist a prosthetic technician in selecting the appropriate casting techniques to obtain the desired alloy properties. Copyright © 2013 Elsevier B.V. All rights reserved.

Gypsum accumulation on carbonate stone

Science.gov (United States)

McGee, E.S.; Mossotti, V.G.

1992-01-01

The accumulation of gypsum on carbonate stone has been investigated through exposure of fresh samples of limestone and marble at monitored sites, through examination of alteration crusts from old buildings and through laboratory experiments. Several factors contribute to gypsum accumulation on carbonate stone. Marble or limestone that is sheltered from direct washing by rain in an urban environment with elevated pollution levels is likely to accumulate a gypsum crust. Crust development may be enhanced if the stone is porous or has an irregular surface area. Gypsum crusts are a surficial alteration feature; gypsum crystals form at the pore opening-air interface, where evaporation is greatest.

Poly(hydroxyalkanoate)s-Based Hydrophobic Coatings for the Protection of Stone in Cultural Heritage.

Science.gov (United States)

Andreotti, Serena; Franzoni, Elisa; Fabbri, Paola

2018-01-20

Reversibility is a mandatory requirement for materials used in heritage conservation, including hydrophobic protectives. Nevertheless, current protectives for stone are not actually reversible as they remain on the surfaces for a long time after their hydrophobicity is lost and can hardly be removed. Ineffective and aged coatings may jeopardise the stone re-treatability and further conservation interventions. This paper aims at investigating the performance of PHAs-based coatings for stone protection, their main potential being the 'reversibility by biodegradation' once water repellency ended. The biopolymer coatings were applied to three different kinds of stone, representative of lithotypes used in historic architecture: sandstone, limestone and marble. Spray, poultice and dip-coating were tested as coating techniques. The effectiveness and compatibility of the protectives were evaluated in terms of capillary water absorption, static and dynamic contact angles, water vapour diffusion, colour alteration and surface morphology. The stones' wettability after application of two commercial protectives was investigated too, for comparison. Finally, samples were subjected to artificial ageing to investigate their solar light stability. Promising results in terms of efficacy and compatibility were obtained, although the PHAs-based formulations developed here still need improvement for increased durability and on-site applicability.

Manufacture of tube billets for fuel cans by vacuum centrifugal casting

International Nuclear Information System (INIS)

Zelenskij, V.F.; Neklyudov, I.M.; Chernyj, B.P.

1989-01-01

Vacuum device for induction melting with centrifugal casting in the ingot mold with rotation vertical or horisontal axis is presented. Removing and grinding of nonmetallic inclusions are realized by selection of casting conditions and of chemically active reducer, sound metal with high ductility is obtained. Data on micro- and macrostructure of casted tube billets made of 08Kh18N10T and 06Kh16H15M3B stainless steels, designed for manufacture of fuel cans are presented

Quantifying the Use of stones in the stone age Fireplaces of Estonia

OpenAIRE

Sikk, Kaarel

2017-01-01

Fireplaces and burnt stones related to them are common features found at Stone Age settlement sites. Although information about them is present in archaeological reports and also available in publications, there has been no general research done regarding combustion features specifically. The purpose of this study was to fill the gap of relevant research and to test the hypothesis that the structural features of fireplaces reveal information on the subsistence model of settlements.The study is b...

Surgical versus endoscopic treatment of bile duct stones

DEFF Research Database (Denmark)

Martin, D J; Vernon, D R; Toouli, J

2006-01-01

10% to 18% of patients undergoing cholecystectomy for gallstones have common bile duct (CBD) stones. Treatment options for these stones include pre- or post-operative endoscopic retrograde cholangiopancreatography (ERCP) or open or laparoscopic surgery.......10% to 18% of patients undergoing cholecystectomy for gallstones have common bile duct (CBD) stones. Treatment options for these stones include pre- or post-operative endoscopic retrograde cholangiopancreatography (ERCP) or open or laparoscopic surgery....

Role of alpha-1 blocker in expulsion of stone fragments after extracorporeal shock wave lithotripsy for renal stones

International Nuclear Information System (INIS)

Pirzada, A.J.; Anwar, A.; Javed, A.; Memon, I.; Mohammad, A.

2011-01-01

Background: Renal stone disease is a significant and worldwide health problem. Recent advances in stone management have allowed kidney stones to be treated using extracorporeal shock wave lithotripsy (ESWL), uretero-renoscopy (URS), and percutaneous nephrostolithotomy (PCNL). Recently, medical expulsion therapy (MET) has been investigated as a supplement to observation in an effort to improve spontaneous stone passage rates. Patients and Methods: This study was a randomized, controlled, prospective study to determine whether the administration of Alpha-1-adrenergic receptor antagonists as an adjunctive medical therapy, increases the efficacy of ESWL to treat renal stones. Sixty patients with renal stones of 0.5-1.5 Cm in size (average size 1.2 Cm) were included in this study underwent ESWL followed by administration of Alpha-1-adrenergic receptor antagonists at department of Urology Liaquat National Hospital Karachi from Feb 2008 to Sept 2008. This was a comparative study and patients were divided into two groups. In group A patients received conventional treatment Diclofenac sodium, Anti Spasmodic (Drotaverine HCl) as required and Proton Pump inhibitor (Omeprazole 20 mg) once daily after shock wave lithotripsy. In group B patients received alpha-1 blocker, Alfuzosin HCl 5 mg twice daily in addition to conventional treatment. All patients were instructed to drink a minimum of 2 litres water daily. Ultrasound guided Dornier Alpha Impact Lithotripter was utilised for shock wave lithotripsy. Results: Of the 60 patients, 76.7% of those receiving Alfuzosin and 46.7% of controls had achieved clinical success at 1 month (p=0.01). The mean cumulative diclofenac dose was 485 mg per patient in the Alfuzosin group and 768 mg per patient in the control group (p=0.002). This difference was statistically significant. Conclusion: Alfuzosin therapy as an adjunctive medical therapy after ESWL is more effective than lithotripsy alone for the treatment of patients with large renal

Use of the probability of stone formation (PSF) score to assess stone forming risk and treatment response in a cohort of Brazilian stone formers.

Science.gov (United States)

Turney, Benjamin; Robertson, William; Wiseman, Oliver; Amaro, Carmen Regina P R; Leitão, Victor A; Silva, Isabela Leme da; Amaro, João Luiz

2014-01-01

The aim was to confirm that PSF (probability of stone formation) changed appropriately following medical therapy on recurrent stone formers. Data were collected on 26 Brazilian stone-formers. A baseline 24-hour urine collection was performed prior to treatment. Details of the medical treatment initiated for stone-disease were recorded. A PSF calculation was performed on the 24 hour urine sample using the 7 urinary parameters required: voided volume, oxalate, calcium, urate, pH, citrate and magnesium. A repeat 24-hour urine sample was performed for PSF calculation after treatment. Comparison was made between the PSF scores before and during treatment. At baseline, 20 of the 26 patients (77%) had a high PSF score (> 0.5). Of the 26 patients, 17 (65%) showed an overall reduction in their PSF profiles with a medical treatment regimen. Eleven patients (42%) changed from a high risk (PSF > 0.5) to a low risk (PSF 0.5) during both assessments. The PSF score reduced following medical treatment in the majority of patients in this cohort.

Use of the probability of stone formation (PSF score to assess stone forming risk and treatment response in a cohort of Brazilian stone formers

Directory of Open Access Journals (Sweden)

Benjamin Turney

2014-08-01

Full Text Available Introduction The aim was to confirm that PSF (probability of stone formation changed appropriately following medical therapy on recurrent stone formers. Materials and Methods Data were collected on 26 Brazilian stone-formers. A baseline 24-hour urine collection was performed prior to treatment. Details of the medical treatment initiated for stone-disease were recorded. A PSF calculation was performed on the 24 hour urine sample using the 7 urinary parameters required: voided volume, oxalate, calcium, urate, pH, citrate and magnesium. A repeat 24-hour urine sample was performed for PSF calculation after treatment. Comparison was made between the PSF scores before and during treatment. Results At baseline, 20 of the 26 patients (77% had a high PSF score (> 0.5. Of the 26 patients, 17 (65% showed an overall reduction in their PSF profiles with a medical treatment regimen. Eleven patients (42% changed from a high risk (PSF > 0.5 to a low risk (PSF 0.5 during both assessments. Conclusions The PSF score reduced following medical treatment in the majority of patients in this cohort.

The structure of abrasion-resisting castings made of chromium cast iron

Directory of Open Access Journals (Sweden)

D. Kopyciński

2011-01-01

Full Text Available In this study presents the analyse of chrome iron cast structure (as-cast condition which are used in rugged conditions abrasion-percussive and high temperature. While producing the casts of chrome iron major influence has been preserve the structure of technologi cal process parameters. The addition to Fe-C-Cr alloy Ni, Mo or Cu and then proper heat treatment leads to the improvement of functional and mechanical cast qualities. Then it is possible to develop high mechanical properties which are recommended by PN-EN12513. As can it be seen from the above research silicon is an adverse chemical element in this kind of alloy cast iron. However, the reason of cracksappearing in chrome iron casts are phosphorus eutectic microareas. When the compound of Si and P reach the critical point, described inPN-88/H-83144 outdated standard, the microareas might appear.

The deformation of wax patterns and castings in investment casting technology

Directory of Open Access Journals (Sweden)

A. Herman

2012-01-01

Full Text Available The dimensional accuracy of the final casting of Inconel alloy 738 LC is affected by many aspects. One of them is the choice of method and time of cooling wax model for precision investment casting. The main objective was to study the initial deformation of the complex shape of the casting of the rotor blades. Various approaches have been tested for cooling wax pattern. When wax models are cooling on the air, without clamping in jig for cooling, deviations from the ideal shape of the casting are very noticeable (up to 8 mm and most are in extreme positions of the model. When blade is cooled in fixing jig in water environment, the resulting deviations compared with cooling in air are significantly larger, sometimes up to 10 mm. This itself does not mean that the final shape of the casting is dimensionally more accurate with usage of wax models, which have deviations from the ideal position smaller. Another deformation occurs when shell mould is produced around wax pattern and furthermore deformations emerge while casting of blade is cooling. This paper demonstrates first steps in describing complex process of deformations of Inconel alloy blades produced with investment casting technology by comparing results from thermal imagery, simulations in foundry simulation software ProCAST 2010 and measurements from CNC scanning system Carl Zeiss MC 850. Conclusions are so far not groundbreaking, but it seems deformations of wax pattern and deformations of castings do in some cases cancel each other by having opposite directions. Describing entirely whole process of deformations will help increase precision of blade castings so that models at the beginning and blades in the end are the same.

The "Global Heritage Stone Resource": Past, Present and Future

Science.gov (United States)

Cooper, Barry

2013-04-01

The "Global Heritage Stone Resource" designation arose in 2007 as a suggested mechanism to enhance international recognition of famous dimension stones. There were also many aspects of dimension stone study that had no formal recognition in mainstream geology and which could be recognised in a formal geological sense via an internationally acceptable geological standard. Such a standard could also receive recognition by other professionals and the wider community. From the start, it was appreciated that active quarrying would an important aspect of the designation so a designation different to any other standard was needed. Also the project was linked to the long-established Commission C-10 Building Stone and Ornamental Rocks of the International Association of Engineering Geology and the Environment (IAEG C-10). Since 2007, the "Global Heritage Stone Resource" (GHSR) proposal has evolved in both in stature and purpose due to an increasing number of interested international correspondents that were actively sought via conference participation. The "English Stone Forum" in particular was pursuing similar aims and was quick to advise that English dimension stone types were being recognised as having international, national or regional importance. Furthermore the proposed designation was suggested as to having significant value in safeguarding designated stone types whilst also providing a potential mechanism in preventing heritage stone replacement by cheap substitutes. During development it also became apparent that stone types having practical applications such as roofing slates and millstones or even stone types utilised by prehistoric man can also be recognised by the new designation. The heritage importance of architects was also recognised. Most importantly an international network evolved, primarily including geologists, that now seems to be the largest international grouping of dimension stone professionals. This has assisted the project to affiliate with the

Extracorporeal Shockwave Lithotripsy of Primary Intrahepatic Stones

Science.gov (United States)

Kim, Myung Hwan; Lee, Sung Koo; Min, Young Il; Lee, Mun Gyu; Sung, Kyu Bo; Cho, Kyung Sik; Lee, Sung Gyu; Min, Pyung Chul

1992-01-01

Extracorporeal shockwave lithothripsy (ESWL) was performed in intrahepatic stone patients (n = 18) by Dornier MPL 9,000 with ultrasound guidance. The patients had T-tube (n = 9) or percutaneous transhepatic biliary drainge tube (n = 9). Average treatment session was four and shock-wave numbers were in the range of 3,064 to 12,000 (average 6,288 shocks). Intrahepatic stones were removed completely in 16 patients over a 3 month period by ESWL and combined stone extraction maneuver such as cholangioscopic or interventional radiologic method. Extracorporeal shockwave lithothripsy was very helpful in facilitating extraction of stones in unfavorable locations or located above the severe stricture. In summary, extracorporeal Shockwave lithotripsy, followed by percutaneous stone extraction, will provide an improvement in the success rate and duration of treatment required for complete removal of primary hepatolithiasis. PMID:1477027

Production and characterization of composite stone

International Nuclear Information System (INIS)

Leirose, G.D.; Lameiras, F.S.

2012-01-01

Composite stone is a product similar to natural granite or marble, produced with particles of these materials. This material is used like natural stone as lining. The fabrication of artificial stones using residues of banded iron formations is a promising alternative to its actual destination (storage in dam). This research aims the characterization of composite stone to prove the efficacy of this kind of processing. It was used first, natural quartz as a raw material. The patterns of the samples were confirmed by IR spectra and XRD patterns, ensuring the reproducibility of processing applied. Moreover, this material is homogeneous, with low porosity and high flexural strength, confirmed by its structural characterization. Thus, it can be affirmed that the process chosen is suitable, enabling the application of this methodology to the use of waste. (author)

Effectiveness of Treatment Modalities on Kidney Stone Recurrence.

Science.gov (United States)

Zisman, Anna L

2017-10-06

Nephrolithiasis is highly prevalent across all demographic groups in the Western world and beyond, and its incidence rates are rising. In addition to the morbidity of the acute event, stone disease often becomes a lifelong problem that requires preventative therapy to diminish ongoing morbidity. Across the majority of stone types, increased fluid intake and targeted dietary modifications are mainstays of therapy. Specific dietary interventions associated with reduced calcium stone risk include adequate dietary calcium intake and restriction of sodium, protein, and oxalate intake, among others. Pharmaceutical therapy may be required if lifestyle changes are insufficient to minimize risk of stone recurrence, and must be targeted to the specific metabolic abnormalities portending risk for a given patient. Therapeutic options for idiopathic calcium stone disease include thiazides, citrate salts, and uric acid-lowering agents. Alkali salts are also the treatment of choice for uric acid stone disease. Management of struvite stone disease is largely surgical, but acetohydroxamic acid is a proven second line therapy. Cystinuria requires lifestyle modifications and may call for thiol-binding agents. Significant heterogeneity of the clinical population with stone disease has previously limited opportunities for large randomized controlled trials. However, as clinical phenotypes and genotypes are increasingly clarified, there are mounting opportunities for targeted randomized controlled trials in stone prevention. In the meantime, the currently available evidence for both lifestyle and pharmacologic interventions is reviewed herein. Copyright © 2017 by the American Society of Nephrology.

Comparative study on stiffness properties of WOODCAST and conventional casting materials.

Science.gov (United States)

Pirhonen, Eija; Pärssinen, Antti; Pelto, Mika

2013-08-01

Plaster-of-Paris and synthetic materials (e.g. fibreglass) have been in clinical use as casting materials for decades. An innovative casting material, WOODCAST, brings interesting alternatives to the traditional materials. The aim of this study was to compare the stiffness properties of the WOODCAST material to traditional casting materials. In immobilization by casting, materials with variable stiffness properties are required. Ring stiffness of cylindrical samples correlates well with cast rigidity. For load-bearing structures, the use of the WOODCAST Splint is recommended as equally high stiffness was obtained with the WOODCAST Splint as was with fibreglass. The WOODCAST 2 mm product is optimal for structures where some elasticity is required, and WOODCAST Ribbon can be used in any WOODCAST structure where further reinforcement is needed. The results show that WOODCAST material can be used in replacing traditional casting materials used in extremity immobilization. The mechanical properties of casting material play an important role in safe and effective fracture immobilization. Stiffness properties of the WOODCAST casting material and conventional materials - fibreglass and plaster-of-Paris - were analysed in this study. The WOODCAST Splint appears to compare favorably with traditional materials such as Scotchcast.

Efficacy of the lithotripsy in treating lower pole renal stones.

Science.gov (United States)

Cui, Helen; Thomee, Eeke; Noble, Jeremy G; Reynard, John M; Turney, Benjamin W

2013-06-01

Use of extracorporeal lithotripsy is declining in North America and many European countries despite international guidelines advocating it as a first-line therapy. Traditionally, lithotripsy is thought to have poor efficacy at treating lower pole renal stones. We evaluated the success rates of lithotripsy for lower pole renal stones in our unit. 50 patients with lower pole kidney stones ≤15 mm treated between 3/5/11 and 19/4/12 were included in the study. Patients received lithotripsy on a fixed-site Storz Modulith SLX F2 lithotripter according to a standard protocol. Clinical success was defined as stone-free status or asymptomatic clinically insignificant residual fragments (CIRFs) ≤3 mm at radiological follow-up. The mean stone size was 7.8 mm. The majority of stones (66 %) were between 5 and 10 mm. 28 % of stones were between 10 and 15 mm. For solitary lower pole stones complete stone clearance was achieved in 63 %. Total stone clearance including those with CIRFs was achieved in 81 % of patients. As expected, for those with multiple lower pole stones the success rates were lower: complete clearance was observed in 39 % and combined clearance including those with CIRFs was 56 %. Overall, complete stone clearance was observed in 54 % of patients and clearance with CIRFs was achieved in 72 % of patients. Success rate could not be attributed to age, stone size or gender. Our outcome data for the treatment of lower pole renal stones (≤15 mm) compare favourably with the literature. With this level of stone clearance, a non-invasive, outpatient-based treatment like lithotripsy should remain the first-line treatment option for lower pole stones. Ureteroscopy must prove that it is significantly better either in terms of clinical outcome or patient satisfaction to justify replacing lithotripsy.

Analysis of Precious Stones Deposited in Various Rock Samples of Mogok Region by energy dispersive X-ray Fluorescence Spectrometry

International Nuclear Information System (INIS)

Kyi Kyi San; Soe Lwin; Win Win Thar; Sein Htoon

2004-06-01

The analysis of precious stones deposited in various rock samples of Mogok region were investigated by the energy dispersive x-ray fluorescence technique. The x-ray machine with Rh target was used to excite the characteristic x-ray from the sample. X-rays emitted from the sample were measured by a high resolution, cooled Si (Li) detector. The calibration was made by the measurement of minerals which composed in each kind of precious stones. The kind of precious stone deposited in the rocks sample was determined by the measurement of minerals from the rock samples compared with those obtained from each kind of precious stones

Fiber laser cladding of nickel-based alloy on cast iron

Energy Technology Data Exchange (ETDEWEB)

Arias-González, F., E-mail: felipeag@uvigo.es [Applied Physics Dpt., University of Vigo, EEI, Lagoas-Marcosende, Vigo E-36310 (Spain); Val, J. del [Applied Physics Dpt., University of Vigo, EEI, Lagoas-Marcosende, Vigo E-36310 (Spain); Comesaña, R. [Materials Engineering, Applied Mechanics and Construction Dpt., University of Vigo, EEI, Lagoas-Marcosende, Vigo E-36310 (Spain); Penide, J.; Lusquiños, F.; Quintero, F.; Riveiro, A.; Boutinguiza, M.; Pou, J. [Applied Physics Dpt., University of Vigo, EEI, Lagoas-Marcosende, Vigo E-36310 (Spain)

2016-06-30

-based coating obtained presents a significantly superior hardness than cast iron.

Kidney Stones in Children and Teens

Science.gov (United States)

... Issues Listen Español Text Size Email Print Share Kidney Stones in Children and Teens Page Content Article ... teen girls having the highest incidence. Types of Kidney Stones There are many different types of kidney ...

Shape Accuracy of Iron Precision Castings in Terms of Ceramic Moulds Physical Properties Anisotropy

Directory of Open Access Journals (Sweden)

Biernacki R.

2014-03-01

Full Text Available While analyzing shape accuracy of ferroalloy precision castings in terms of ceramic moulds physical anisotropy, low-alloy steel castings ("cover" and cast iron ("plate" were included. The basic parameters in addition to the product linear shape accuracy are flatness deviations, especially due to the expanded flat surface which is cast plate. For mentioned castings surface micro-geometry analysis was also carried, favoring surface load capacity tp50 for Rmax = 50%. Surface load capacity tp50 obtained for the cast cover was compared with machined product, and casting plate surface was compared with wear part of the conveyor belt. The results were referred to anisotropy of ceramic moulds physical properties, which was evaluated by studying ceramic moulds samples in computer tomography equipment Metrotom 800

The Guy's stone score--grading the complexity of percutaneous nephrolithotomy procedures.

Science.gov (United States)

Thomas, Kay; Smith, Naomi C; Hegarty, Nicholas; Glass, Jonathan M

2011-08-01

To report the development and validation of a scoring system, the Guy's stone score, to grade the complexity of percutaneous nephrolithotomy (PCNL). Currently, no standardized method is available to predict the stone-free rate after PCNL. The Guy's stone score was developed through a combination of expert opinion, published data review, and iterative testing. It comprises 4 grades: grade I, solitary stone in mid/lower pole or solitary stone in the pelvis with simple anatomy; grade II, solitary stone in upper pole or multiple stones in a patient with simple anatomy or a solitary stone in a patient with abnormal anatomy; grade III, multiple stones in a patient with abnormal anatomy or stones in a caliceal diverticulum or partial staghorn calculus; grade IV, staghorn calculus or any stone in a patient with spina bifida or spinal injury. It was assessed for reproducibility using the kappa coefficient and validated on a prospective database of 100 PCNL procedures performed in a tertiary stone center. The complications were graded using the modified Clavien score. The clinical outcomes were recorded prospectively and assessed with multivariate analysis. The Guy's stone score was the only factor that significantly and independently predicted the stone-free rate (P = .01). It was found to be reproducible, with good inter-rater agreement (P = .81). None of the other factors tested, including stone burden, operating surgeon, patient weight, age, and comorbidity, correlated with the stone-free rate. The Guy's stone score accurately predicted the stone-free rate after PCNL. It was easy to use and reproducible. Copyright © 2011 Elsevier Inc. All rights reserved.

Colour Metallography of Cast Iron - Chapter 1: Introduction (Ⅰ

Directory of Open Access Journals (Sweden)

Zhou Jiyang

2009-02-01

Full Text Available Cast iron, as a traditional metal material, has advantages of low total cost, good castability and machinability, good wear resistance and low notch sensitivity, and is still facing tough challenge in quality, property and variety of types etc. Experts and engineers studying and producing iron castings all around world extremely concern this serious challenge. Over more than 30 years, a great of research work has been carried out on how to further improve its property, expand its application and combine cast iron technology with some hi-techs (for example, computer technology. Nevertheless, cast iron is a multi-element and multi-phase alloy and has complex and variety of structures and still has great development potential in structure and property. For further studying and developing cast iron, theoretical research work is important promise, and the study on solidification process and control mechanism of graphite morphology is fundamental for improving property of cast iron and developing new type of cast iron. Metallography of cast iron normally includes two sections: liquid phase transformation and solid phase transformation. The book, Colour Metallography of Cast Iron, uses colour metallography technique to study solidification structures of cast irons: graphite, carbides, austenite and eutectics; and focuses on solidification processes. With progress of modern solidification theory, the control of material solidification process becomes important measure for improving traditional materials and developing new materials. Solidification structure not only influences mechanical and physical properties of cast iron, but also affects its internal quality. The book uses a large amount of colour photos to describe the formation of solidification structures and their relations. Crystallization phenomena, which cannot be displayed with traditional metallography, are presented and more phase transformation information is obtained from these colour

Direct Cast U-6Nb – 2017 Progress on Cylindrical Castings

Energy Technology Data Exchange (ETDEWEB)

Aikin, Jr., Robert M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-10-04

This report describes work to further develop a sound technical basis and best practices for mold design and process parameters for the Direct Casting of U-6wt%Nb components. One major challenge to the production of U-6Nb components is the propensity for niobium segregation during casting and solidification. This is especially true for cylindrical castings where the vertical side walls allow flotation of Nb resulting in severe inverse macrosegregation. In this work, a small (120 mm diameter by 180 mm tall) and large cylinder (250 mm diameter by 310 mm tall) are examined with a focus on reducing, or eliminating, niobium segregation. It is demonstrated that counter gravity casting (top-to-bottom solidification) can be used to minimize segregation in the small cylinder. Attempts to counter gravity cast the large cylinder were unsuccessful, in large part due to size limitations of the current furnace. A path forward for casting of the large cylinders is discussed.

X-ray fluorescence control of chemical composition of cast iron

International Nuclear Information System (INIS)

Prekina, I.M.; Rozova, O.F.; Loran, A.V.; Teplitskaya, G.A.; Smagunova, A.N.

1995-01-01

A method of x-ray fluorescence analysis developed for analytical set (KRF-18 diffractometer/DVK-3 computer) is used to control cast iron composition. A quantitative evaluation of errors attributed to the violation of conditions of cast iron sampling from the flow and to the quality of preparing samples for XFA is obtained. It is shown that the main component of the integral experimental error is attributed to nonuniformity of chemical composition of cast iron. Metrological studies show that reproductibility, convergence, accuracy, and sensitivity of the method match the requirements characteristic of the control process. 4 refs.; 2 tabs

Geomorphology's role in the study of weathering of cultural stone

Science.gov (United States)

Pope, Gregory A.; Meierding, Thomas C.; Paradise, Thomas R.

2002-10-01

Great monumental places—Petra, Giza, Angkor, Stonehenge, Tikal, Macchu Picchu, Rapa Nui, to name a few—are links to our cultural past. They evoke a sense of wonderment for their aesthetic fascination if not for their seeming permanence over both cultural and physical landscapes. However, as with natural landforms, human constructs are subject to weathering and erosion. Indeed, many of our cultural resources suffer from serious deterioration, some natural, some enhanced by human impact. Groups from the United Nations to local civic and tourism assemblies are deeply interested in maintaining and preserving such cultural resources, from simple rock art to great temples. Geomorphologists trained in interacting systems, process and response to thresholds, rates of change over time, and spatial variation of weathering processes and effects are able to offer insight into how deterioration occurs and what can be done to ameliorate the impact. Review of recent literature and case studies presented here demonstrate methodological and theoretical advances that have resulted from the study of cultural stone weathering. Because the stone was carved at a known date to a "baseline" or zero-datum level, some of the simplest methods (e.g., assessing surface weathering features or measuring surface recession in the field) provide useful data on weathering rates and processes. Such data are difficult or impossible to obtain in "natural" settings. Cultural stone weathering studies demonstrate the importance of biotic and saline weathering agents and the significance of weathering factors such as exposure (microclimate) and human impact. More sophisticated methods confirm these observations, but also reveal discrepancies between field and laboratory studies. This brings up two important caveats for conservators and geomorphologists. For the conservator, are laboratory and natural setting studies really analogous and useful for assessing stone damage? For the geomorphologist, does

Evidence Report: Risk of Renal Stone Formation

Science.gov (United States)

Sibonga, Jean D.; Pietrzyk, Robert

2017-01-01

The formation of renal stones poses an in-flight health risk of high severity, not only because of the impact of renal colic on human performance but also because of complications that could potentially lead to crew evacuation, such as hematuria, infection, hydronephrosis, and sepsis. Evidence for risk factors comes from urine analyses of crewmembers, documenting changes to the urinary environment that are conducive to increased saturation of stone-forming salts, which are the driving force for nucleation and growth of a stone nidus. Further, renal stones have been documented in astronauts after return to Earth and in one cosmonaut during flight. Biochemical analysis of urine specimens has provided indication of hypercalciuria and hyperuricemia, reduced urine volumes, and increased urine saturation of calcium oxalate and calcium phosphate. A major contributor to the risk for renal stone formation is bone atrophy with increased turnover of the bone minerals. Dietary and fluid intakes also play major roles in the risk because of the influence on urine pH (more acidic) and on volume (decreased). Historically, specific assessments on urine samples from some Skylab crewmembers indicated that calcium excretion increased early in flight, notable by day 10 of flight, and almost exceeded the upper threshold for normal excretion (300mg/day in males). Other crewmember data documented reduced intake of fluid and reduced intake of potassium, phosphorus, magnesium, and citrate (an inhibitor of calcium stone formation) in the diet. Hence, data from both short-duration and long-duration missions indicate that space travel induces risk factors for renal stone formation that continue to persist after flight; this risk has been documented by reported kidney stones in crewmembers.

[Components of urinary crystallites in urine of uric acid stone formers and its relationship with formation of stones].

Science.gov (United States)

Huang, Zhi-jie; Tan, Jin; Ouyang, Jian-ming

2010-09-01

The components, zeta potential, morphology of nanocrystallites in urines of 10 uric acid stone formers as well as their relationship with the formation of uric acid stones were comparatively studied using X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, nanoparticle size analyzer, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The urine pH of uric acid stone formers was relatively low within the range of 4.8 to 5.7. The main constituent of urinary crystallites was uric acid. Their particle size distribution was highly uneven, ranging from several nanometers to several tens of micrometers, and obvious aggregation was observed. The zeta potential of urinary crystallites in ten lithogenic patients was -6.02 mV, which was higher than that in ten normal subjects (-10.1 mV). After drug therapies (potassium citrate was taken), the urine pH value of the uric acid stone formers increased to 6.5 or so, and at this pH value most of the uric acid had changed to urate. Since the solubility of urate increased greatly than uric acid, the risk of the formation of uric acid stone reduced. The results in this paper showed that there was a close relationship among stone components, urinary crystallites composition and urine pH.

Famous Stone Patients and Their Disease

Science.gov (United States)

Moran, Michael E.

2007-04-01

The fact that stone patients have endured much throughout the ages and that prior to our current era, when the ultimate horror, "being cut for the stone" was the only alternative to the repeated episodes of colic, should be recalled from time to time. Urolithiasis has affected humanity throughout the ages and has been indiscriminate to those lives it touched. A full accounting of those who have suffered and recorded their agonies is beyond the scope of this investigation; however, even a partial accounting is valuable for present day physicians who care for those with stone disease. For the present work, the historical accounts of stone disease literature were scrutinized for individual sufferers who could be cross-referenced from other sources as legitimately afflicted by stones. Only those patients that could be documented and were (or are) well known were included, because the internet is now a verdant repository of thousands of "not so well knowns." Reliable historical data was found for a variety of persons from the pre-Christian era to the present, including those remembered as philosophers and scientists, physicians, clergy, leaders and rulers, entertainers, athletes and fictitious/Hollywood-type individuals. Verified accounts of famous stone formers were chosen for this paper, and are presented in chronological order. The list of urolithiasis sufferers presented here is undoubtedly incomplete, but it is not through lack of trying that they are missing. Most often, the suffering do so silently, and that is always allowed.

Retroperitoneoscopy for treatment of renal and ureteral stones.

Science.gov (United States)

Soares, Rodrigo S; Romanelli, Pedro; Sandoval, Marcos A; Salim, Marcelo M; Tavora, Jose E; Abelha, David L

2005-01-01

To assess the efficacy of retroperitoneoscopy for treating stones in the renal pelvis and proximal ureter. In the period from August 2003 to August 2004, 35 retroperitoneoscopies for treatment of urinary stones were performed on 34 patients. Fifteen patients (42%) had stones in the renal pelvis, and in 2 cases, there were associated stones in the upper caliceal group. Twenty patients (58%) had ureteral stones, all of them located above the iliac vessel. Twenty-five patients (71%) had previously undergone at least one session of extracorporeal lithotripsy and 8 patients (26%) also underwent ureteroscopy to attempt to remove the stone. Eight patients underwent retroperitoneoscopy as a primary procedure. Stone size ranged from 0.5 to 6 cm with a mean of 2.1 cm. Retroperitoneoscopy was performed by lumbar approach with initial access conducted by open technique and creation of space by digital dissection. We used a 10-mm Hasson trocar for the optics, and 2 or 3 additional working ports placed under visualization. Following identification, the urinary tract was opened with a laparoscopic scalpel and the stone was removed intact. The urinary tract was closed with absorbable 4-0 suture and a Penrose drain was left in the retroperitoneum. In 17 patients (49%), a double-J stent was maintained postoperatively. Surgical time ranged from 60 to 260 minutes with a mean of 140 minutes. The mean hospital stay was 3 days (1-10 days). The mean length of retroperitoneal urinary drainage was 3 days (1-10 days). There were minor complications in 6 (17.6%) patients and 1 case of conversion due to technical difficulty. Thirty-three patients (94%) became stone free. Retroperitoneoscopy is an effective, low-morbidity alternative for treatment of urinary stones.

Retroperitoneoscopy for treatment of renal and ureteral stones

Directory of Open Access Journals (Sweden)

Rodrigo S. Soares

2005-04-01

Full Text Available OBJECTIVE: To assess the efficacy of retroperitoneoscopy for treating stones in the renal pelvis and proximal ureter. MATERIALS AND METHODS: In the period from August 2003 to August 2004, 35 retroperitoneoscopies for treatment of urinary stones were performed on 34 patients. Fifteen patients (42% had stones in the renal pelvis, and in 2 cases, there were associated stones in the upper caliceal group. Twenty patients (58% had ureteral stones, all of them located above the iliac vessel. Twenty-five patients (71% had previously undergone at least one session of extracorporeal lithotripsy and 8 patients (26% also underwent ureteroscopy to attempt to remove the stone. Eight patients underwent retroperitoneoscopy as a primary procedure. Stone size ranged from 0.5 to 6 cm with a mean of 2.1 cm. RESULTS: Retroperitoneoscopy was performed by lumbar approach with initial access conducted by open technique and creation of space by digital dissection. We used a 10-mm Hasson trocar for the optics, and 2 or 3 additional working ports placed under visualization. Following identification, the urinary tract was opened with a laparoscopic scalpel and the stone was removed intact. The urinary tract was closed with absorbable 4-0 suture and a Penrose drain was left in the retroperitoneum. In 17 patients (49%, a double-J stent was maintained postoperatively. Surgical time ranged from 60 to 260 minutes with a mean of 140 minutes. The mean hospital stay was 3 days (1-10 days. The mean length of retroperitoneal urinary drainage was 3 days (1-10 days. There were minor complications in 6 (17.6% patients and 1 case of conversion due to technical difficulty. Thirty-three patients (94% became stone free. CONCLUSION: Retroperitoneoscopy is an effective, low-morbidity alternative for treatment of urinary stones.

INCREASING DEMANDS FOR NATURAL STONES USAGE AROUND THE WORLD

Directory of Open Access Journals (Sweden)

HASAN ÜÇPIRTI

1998-12-01

Full Text Available Due to great demands in construction business, the stone industry has been growing very fast around the world. In fact, the technological iınproveınents on the ınachinery of marble and granite processing plant and quarry in recent years gives impulse to the stone business. According to studies reported� there are recognizable increments on both productions and constructions. Natural stones become driving forces in tl1e countries economy. In this study� so ın e statistical nuınbers for productions and consumption of natural stones will be presented in a base of countries that strongly involve in stone business. The importance of the econoınical impacts of natural stone on countries econoıny wiJI be emphasized. Then, the future of natural stones and its business will be discussed

Tribological Properties of AlSi11-SiCp Composite Castings Produced by Pressure Die Casting Method

Directory of Open Access Journals (Sweden)

Konopka Z.

2014-08-01

Full Text Available The measurement results concerning the abrasive wear of AlSi11-SiC particles composites are presented in paper. The method of preparing a composite slurry composed of AlSi11 alloy matrix and 10, 20% vol.% of SiC particles, as well as the method of its high-pressure die casting was described. Composite slurry was injected into metal mould of cold chamber pressure die cast machine and castings were produced at various values of the piston velocity in the second stage of injection, diverse intensification pressure values, and various injection gate width values. Very good uniform arrangement of SiC particles in volume composite matrix was observed and these results were publicated early in this journal. The kinetics of abrasive wear and correlation with SiC particles arrangement in composite matrix were presented. Better wear resistance of composite was observed in comparison with aluminium alloy. Very strong linear correlation between abrasive wear and particle arrangement was observed. The conclusion gives the analysis and the interpretation of the obtained results.

Microstructure of As-cast Co-Cr-Mo Alloy Prepared by Investment Casting

Science.gov (United States)

Park, Jong Bum; Jung, Kyung-Hwan; Kim, Kang Min; Son, Yong; Lee, Jung-Il; Ryu, Jeong Ho

2018-04-01

The microstructure of a cobalt-base alloy (Co-Cr-Mo) obtained by an investment casting process was studied. This alloy complies with the ASTM F75 standard and is widely used in the manufacturing of orthopedic implants owing to its high strength, good corrosion resistance, and excellent biocompatibility. This work focuses on the resulting microstructures arising from normal industrial environmental conditions. The characterization of the samples was carried out using optical microscopy, field emission scanning electron microscopy and energy-dispersive spectroscopy. In this study, the as-cast microstructure is an γ-Co (face-centered cubic) dendritic matrix with the presence of a secondary phase, such as M23C6 carbides precipitated at grain boundaries and interdendritic zones. These precipitates are the main strengthening mechanism in this type of alloy. Other minority phases, such as the σ phase, were also detected, and their presence could be linked to the manufacturing process and environment.

Cast iron - a predictable material

Directory of Open Access Journals (Sweden)

Jorg C. Sturm

2011-02-01

Full Text Available High strength compacted graphite iron (CGI or alloyed cast iron components are substituting previously used non-ferrous castings in automotive power train applications. The mechanical engineering industry has recognized the value in substituting forged or welded structures with stiff and light-weight cast iron castings. New products such as wind turbines have opened new markets for an entire suite of highly reliable ductile iron cast components. During the last 20 years, casting process simulation has developed from predicting hot spots and solidification to an integral assessment tool for foundries for the entire manufacturing route of castings. The support of the feeding related layout of the casting is still one of the most important duties for casting process simulation. Depending on the alloy poured, different feeding behaviors and self-feeding capabilities need to be considered to provide a defect free casting. Therefore, it is not enough to base the prediction of shrinkage defects solely on hot spots derived from temperature fields. To be able to quantitatively predict these defects, solidification simulation had to be combined with density and mass transport calculations, in order to evaluate the impact of the solidification morphology on the feeding behavior as well as to consider alloy dependent feeding ranges. For cast iron foundries, the use of casting process simulation has become an important instrument to predict the robustness and reliability of their processes, especially since the influence of alloying elements, melting practice and metallurgy need to be considered to quantify the special shrinkage and solidification behavior of cast iron. This allows the prediction of local structures, phases and ultimately the local mechanical properties of cast irons, to asses casting quality in the foundry but also to make use of this quantitative information during design of the casting. Casting quality issues related to thermally driven

Unravelling ground stone life histories: the spatial organization of stone tools and human activities at LN Makriyalos, Greece:

OpenAIRE

Tsoraki, Christina

2007-01-01

Unlike previous studies of ground stone technology in the Greek Neolithic, this paper follows a more contextualised approach by looking at contexts of deposition of ground stone from Late Neolithic Makriyalos, Northern Greece. The patterns attested in the distribution of ground stone objects between domestic and communal areas will be discussed in terms of the spatial and social contexts of tool use, curation and deposition, contributing to wider discussions about the way acts of production, ...

Surface roughness characterization of cast components using 3D optical methods

DEFF Research Database (Denmark)

Nwaogu, Ugochukwu Chibuzoh; Tiedje, Niels Skat; Hansen, Hans Nørgaard

scanning probe image processor (SPIP) software and the results of the surface roughness parameters obtained were subjected to statistical analyses. The bearing area ratio was introduced and applied to the surface roughness analysis. From the results, the surface quality of the standard comparators...... is successfully characterised and it was established that the areal parameters are more informative for sand cast components. The roughness values of the standard visual comparators can serve as a control for the cast components and for order specifications in the foundry industry. A series of iron castings were...... made in green sand moulds and the surface roughness parameter (Sa) values were compared with those of the standards. Sa parameter suffices for the evaluation of casting surface texture. The S series comparators showed a better description of the surface of castings after shot blasting than the A series...

Stone-free-rate after extracorporeal shockwave lithotripsy in the management of pediatric renal stones in lower pole and other locations - a comparative study

International Nuclear Information System (INIS)

Iqbal, N.; Muhammad, S.; Akhter, S.

2016-01-01

To determine a difference in the stone-free-rate among different renal locations in children after extracorporeal shockwave lithotripsy (ESWL). Study Design: A descriptive study. Place and Duration of Study: Urology Department, Shifa International Hospital, Islamabad, Pakistan, from January 2007 to June 2015. Methodology: The study included children who underwent ESWL, divided into three groups based on location of stones in kidney as group A (lower pole stones), group B (upper and mid pole stones) and group C (renal pelvis stone), respectively. ESWL was done by standard technique using Storz Modulith SLX lithotripter 3rd generation. Data was collected by chart review. SPSS version 16 was used for data analysis. Results: Among 76 children with mean age of 7.55 +-4.16 years, 55 (72.4%) were males whereas 21 (27.6%) were females. Mean stone size was 1.08 +-0.59 cm. There were 34, 17 and 25 cases in groups A, B and C, respectively. PostESWL stone-free-rate was 47% in lower pole stones, 70.58% in upper and mid pole stones, and 68% in renal pelvis stones. Hematuria was seen in one patient from each group, sepsis in two patients from each of the mid pole/upper pole and lower pole group, while Steinstrasse in one patient from each group. (author)