WorldWideScience

Sample records for stimulating oil wells

  1. Performance of Surfactant Methyl Ester Sulphonate solution for Oil Well Stimulation in reservoir sandstone TJ Field

    Science.gov (United States)

    Eris, F. R.; Hambali, E.; Suryani, A.; Permadi, P.

    2017-05-01

    Asphaltene, paraffin, wax and sludge deposition, emulsion and water blocking are kinds ofprocess that results in a reduction of the fluid flow from the reservoir into formation which causes a decrease of oil wells productivity. Oil well Stimulation can be used as an alternative to solve oil well problems. Oil well stimulation technique requires applying of surfactant. Sodium Methyl Ester Sulphonate (SMES) of palm oil is an anionic surfactant derived from renewable natural resource that environmental friendly is one of potential surfactant types that can be used in oil well stimulation. This study was aimed at formulation SMES as well stimulation agent that can identify phase transitions to phase behavior in a brine-surfactant-oil system and altered the wettability of rock sandstone and limestone. Performance of SMES solution tested by thermal stability test, phase behavioral examination and rocks wettability test. The results showed that SMES solution (SMES 5% + xylene 5% in the diesel with addition of 1% NaCl at TJformation water and SMES 5% + xylene 5% in methyl ester with the addition of NaCl 1% in the TJ formation water) are surfactant that can maintain thermal stability, can mostly altered the wettability toward water-wet in sandstone reservoir, TJ Field.

  2. PEMANFAATAN METIL ESTER JARAK PAGAR MENJADI SURFAKTAN MES UNTUK APLIKASI SEBAGAI OIL WELL STIMULATION AGENT

    Directory of Open Access Journals (Sweden)

    Erliza Hambali

    2012-04-01

    Full Text Available Year by year, globally the production of petroleum decreases but its demand increases. The world will get the energy crisis including Indonesia if that condition happens continously. Because of that, Indonesia starts to develop IOR (improved oil recovery method for their oil fields. IOR method is an improvement of the secondary phase in which the oil recovery is expected to increase oil production. One method of IOR is chemical injection with surfactant for injection. Surfactant is dissolved with injection water and injected to reservoir. Generally, surfactant of petroleum sulphonates is used for oil recovery. Due to the weaknesses of petroleum suphonates such as not resistant in high salinity and high hardness water, therefore it triggers to get surfactant substitute like MES (methyl ester sulphonates that is synthesized by bio-oil from Jatropha curcas L. The study was aimed to know the performance of MES surfactant formula from jatropha oil for IOR in fluid sample of oil field and synthetic sandstone core. The best condition from this research was surfactant 0.2 PV with the soaking time of 12 hours. This formula gave the highest of incremental total oil recovery 61%. The number were resulted from 48% waterflooding and 13% surfactant injection.

  3. Analytical filtration model for nonlinear viscoplastic oil in the theory of oil production stimulation and heating of oil reservoir in a dual-well system

    Science.gov (United States)

    Ivanovich Astafev, Vladimir; Igorevich Gubanov, Sergey; Alexandrovna Olkhovskaya, Valeria; Mikhailovna Sylantyeva, Anastasia; Mikhailovich Zinovyev, Alexey

    2018-02-01

    Production of high-viscosity oil and design of field development systems for such oil is one of the most promising directions in the development of world oil industry. The ability of high-viscosity oil to show in filtration process properties typical for non-Newtonian systems is proven by experimental studies. Nonlinear relationship between the pressure gradient and the rate of oil flow is due to interaction of high-molecular substances, in particular, asphaltenes and tars that form a plastic structure in it. The authors of this article have used the analytical model of stationary influx of nonlinear viscoplastic oil to the well bottom in order to provide rationale for the intensifying impact on a reservoir. They also have analyzed the method of periodic heating of productive reservoir by means of dual-wells. The high-temperature source is placed at the bottom of the vertical well, very close to the reservoir; at the same time the side well, located outside the zone of expected rock damage, is used for production. Suggested method of systemic treatment of reservoirs with dual wells can be useful for small fields of high-viscosity oil. The effect is based on the opportunity to control the structural and mechanical properties of high-viscosity oil and to increase depletion of reserves.

  4. 77 FR 27691 - Oil and Gas; Well Stimulation, Including Hydraulic Fracturing, on Federal and Indian Lands

    Science.gov (United States)

    2012-05-11

    ... generally generate flow of hydrocarbons to well bores unless mechanical changes to the properties of the..., Division Chief, Fluid Minerals Division, 202-912-7143 for information regarding the substance of the rule or information about the BLM's Fluid Minerals Program. Persons who use a telecommunications device...

  5. Geothermal Reservoir Well Stimulation Program: technology transfer

    Energy Technology Data Exchange (ETDEWEB)

    1980-05-01

    A literature search on reservoir and/or well stimulation techniques suitable for application in geothermal fields is presented. The literature on stimulation techniques in oil and gas field applications was also searched and evaluated as to its relevancy to geothermal operations. The equivalent low-temperature work documented in the open literature is cited, and an attempt is made to evaluate the relevance of this information as far as high-temperature stimulation work is concerned. Clays play an important role in any stimulation work. Therefore, special emphasis has been placed on clay behavior anticipated in geothermal operations. (MHR)

  6. Oil well spill trough

    International Nuclear Information System (INIS)

    Wigington, J.R. Sr.

    1992-01-01

    This patent describes a process involving an oil well and rig having a casing, a platform on the rig extending around the casing. This patent describes improvement in pulling the tubing from the casing; disconnecting joints of tubing thereby; and spilling liquids from the casing, catching spilled liquids from the casing in a basin below the platform, draining the basin substantially simultaneously; connecting the drain hole to a tank, and reducing the pressure in the tank to less than atmospheric pressure. This paper also describes an oil well and rig having a casing; the rig having a platform extending around the casing. This patent describes improvement in a basin surrounding the casing and connected thereto, the basin below the platform, a drain connection in the lower part of the basin, a conduit connected to the drain, and means for applying a suction to the conduit

  7. STIMULATION TECHNOLOGIES FOR DEEP WELL COMPLETIONS

    Energy Technology Data Exchange (ETDEWEB)

    Stephen Wolhart

    2003-06-01

    The Department of Energy (DOE) is sponsoring a Deep Trek Program targeted at improving the economics of drilling and completing deep gas wells. Under the DOE program, Pinnacle Technologies is conducting a project to evaluate the stimulation of deep wells. The objective of the project is to assess U.S. deep well drilling & stimulation activity, review rock mechanics & fracture growth in deep, high pressure/temperature wells and evaluate stimulation technology in several key deep plays. Phase 1 was recently completed and consisted of assessing deep gas well drilling activity (1995-2007) and an industry survey on deep gas well stimulation practices by region. Of the 29,000 oil, gas and dry holes drilled in 2002, about 300 were drilled in the deep well; 25% were dry, 50% were high temperature/high pressure completions and 25% were simply deep completions. South Texas has about 30% of these wells, Oklahoma 20%, Gulf of Mexico Shelf 15% and the Gulf Coast about 15%. The Rockies represent only 2% of deep drilling. Of the 60 operators who drill deep and HTHP wells, the top 20 drill almost 80% of the wells. Six operators drill half the U.S. deep wells. Deep drilling peaked at 425 wells in 1998 and fell to 250 in 1999. Drilling is expected to rise through 2004 after which drilling should cycle down as overall drilling declines.

  8. Well screening for matrix stimulation treatments

    International Nuclear Information System (INIS)

    Saavedra, N; Solano, R; Gidley, J; Reyes, C.A; Rodriguez; Kondo, F; Hernandez, J

    1998-01-01

    Matrix acidizing is a stimulation technique only applicable to wells with surrounding damage. It is therefore very important to differentiate the real formation damage from the damage caused by flow Ni dynamic effects. The mechanical damage corresponds to flow restrictions caused by partial penetration, poor perforation as well as to reduce diameters of the production tubing. The dynamic effects are generated by inertia caused by high flow rates and high-pressure differentials. A common practice in our oil fields is to use a general formulation as acid treatment, most of the times without previous lab studies that guarantee the applicability of the treatment in the formation. Additionally, stimulation is randomly applied even treating undamaged wells with negative results and in the best of the cases, loss of the treatment. The selection of the well for matrix stimulation is an essential factor for the success of the treatment. Selection is done through the evaluation of the skin factor (S) and of the economic benefits of reducing the skin in comparison to the cost of the work. The most appropriate tool for skin evaluation is a good pressure test where the radial flow period can be identified. Nevertheless, we normally find-outdated tests most of the times taken with inaccurate tools. The interpretation problem is worsened by completions in which there is simultaneous production from several sand packages and it is difficult to individually differentiate damage factors. This works states a procedure for the selection of wells appropriate for stimulation; it also proposes a method to evaluate the skin factor when there are no accurate interpretations of the pressure tests. A new and increasingly applied methodology to treat wells with high water cuts, which are usually discarded due to the risk of stimulating water zones, is also mentioned

  9. Geothermal Reservoir Well Stimulation Program: technology transfer

    Energy Technology Data Exchange (ETDEWEB)

    1980-05-01

    Each of the following types of well stimulation techniques are summarized and explained: hydraulic fracturing; thermal; mechanical, jetting, and drainhole drilling; explosive and implosive; and injection methods. Current stimulation techniques, stimulation techniques for geothermal wells, areas of needed investigation, and engineering calculations for various techniques. (MHR)

  10. Radioisotope techniques in oil wells

    International Nuclear Information System (INIS)

    Jain, Prabuddha

    1998-01-01

    Radioisotope techniques are quite useful in oil exploration and exploitation. Nuclear logging offers a way of gathering information on porosity, permeability, fluid saturations, hydrocarbon types and lithology. Some of the interesting applications in well drilling are determining depth of filtrate invasion, detection of lost circulation, drill-bit erosion control; primary cement measurements and well completions such as permanent tubular markers, perforation position marking, detection of channeling behind casing and gravel pack operations. Radioisotopes have been successfully used in optimizing production processes such as production profiling injection profiling, corrosion measurements and well to well tracer tests. (author)

  11. Well integrity in heavy oil wells : challenges and solutions

    Energy Technology Data Exchange (ETDEWEB)

    Taoutaou, S.; Osman, T.M.; Mjthab, M. [Schlumberger (Syrian Arab Republic); Succar, N. [Oudeh Petroleum, Damascus (Syrian Arab Republic)

    2010-07-01

    The Oudeh Petroleum Company (OPC) has used cyclic steam (the Huff and Puff technique) since 2006 to produce heavy oil from its OPC field that has an estimated 79.49 to 95.39 million cubic meters of oil contained in the Jurassic and Triassic reservoirs of the Butmah and Kurachine formations in Syria. Accumulations of oil and gas are present in the main Oudeh structure at depths between 1300 and 2250 meters. The Huff and Puff technique involves 3 phases. In the first phase which lasts about 1 month, steam is injected at 348 degrees C and 17.MPa to melt the wax condensate in the formation in order to decrease heavy oil viscosity. Phase 2 involves 3 soaking days. In phase 3, which lasts 2 to 3 months, the production rate is doubled compared to wells without steam. The cycle is then resumed once the pressure drops. The temperature cycling can compromise the well integrity through loss of hydraulic isolation in the cement sheath and thereby reduce hydrocarbon recovery. This paper described how the OPC has managed to achieved complete well integrity using an advanced cement system in more than 200 wells exposed to steam injection temperatures up to 348 degrees C and the associated high induced thermal stresses. The methodology for risk analysis of the cement sheath failure under steam stimulation was described along with the selection criteria for the advanced cement system to withstand temperature cycling. Two case histories involving a 50 well database were presented. 5 refs., 2 tabs., 13 figs.

  12. Stimulation Technologies for Deep Well Completions

    Energy Technology Data Exchange (ETDEWEB)

    Stephen Wolhart

    2005-06-30

    The Department of Energy (DOE) is sponsoring the Deep Trek Program targeted at improving the economics of drilling and completing deep gas wells. Under the DOE program, Pinnacle Technologies conducted a study to evaluate the stimulation of deep wells. The objective of the project was to review U.S. deep well drilling and stimulation activity, review rock mechanics and fracture growth in deep, high-pressure/temperature wells and evaluate stimulation technology in several key deep plays. This report documents results from this project.

  13. Stimulation Technologies for Deep Well Completions

    Energy Technology Data Exchange (ETDEWEB)

    None

    2003-09-30

    The Department of Energy (DOE) is sponsoring the Deep Trek Program targeted at improving the economics of drilling and completing deep gas wells. Under the DOE program, Pinnacle Technologies is conducting a study to evaluate the stimulation of deep wells. The objective of the project is to assess U.S. deep well drilling & stimulation activity, review rock mechanics & fracture growth in deep, high pressure/temperature wells and evaluate stimulation technology in several key deep plays. An assessment of historical deep gas well drilling activity and forecast of future trends was completed during the first six months of the project; this segment of the project was covered in Technical Project Report No. 1. The second progress report covers the next six months of the project during which efforts were primarily split between summarizing rock mechanics and fracture growth in deep reservoirs and contacting operators about case studies of deep gas well stimulation.

  14. Controlled PVTS oil and gas production stimulation system

    Energy Technology Data Exchange (ETDEWEB)

    Ospina-Racines, E

    1970-02-01

    By completing oil- or gas-producing wells according to the PVTS method and energizing the flow of the oil-gas fluids in the reservoir with a small horse-power gas compressor at the wellhead, the following oil and gas production features are attained: (1) Original reservoir story energy conditions are restored, improved, used, and conserved while producing oil and/or gas. (2) The flow of oil or gas in the pay formation to the well bore is stimulated by gas compressor energy, outside of the reservoir system. The pressure drawdown is developed by gas-compressor energy in the well casing and not in the pay formation. (3) The stored energy of the reservoir is conserved while producing oil or gas. The potential energy (pressure) of the reservoir can be used to advantage up to bubble point of the virgin crude. (4) Producible reserves are increased from 4-to 5-fold by the conservation of reservoir energy. Present-day primary oil production practice yields a maximum of 20% of the oil in place by depleting the original reservoir energy. The PVTS system will yield over 80% + of oil in place. (5) Producible gas reserves can be increased greatly by establishing a low abandonment pressure at will. The principal features of the PVTS well mechanism and energy injection method are illustrated by a schematic diagram.

  15. Marginal Expense Oil Well Wireless Surveillance (MEOWWS)

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, Donald G.

    2002-03-11

    The objective of this study was to identify and field test a new, low cost, wireless oil well surveillance system. A variety of suppliers and technologies were considered. One supplier and system was chosen that was low cost, new to the oil field, and successfully field tested.

  16. Horizontal well impact on heavy oil supply

    International Nuclear Information System (INIS)

    Bowers, B.; Bielecki, J.; Hu, J.; Wall, B.; Drummond, K.

    1993-01-01

    Horizontal wells can take advantage of gravity drainage mechanisms, which can be important in conventional heavy oil and bitumen recovery. Horizontal drilling will impact on the development of established conventional heavy oil pools by infill drilling and application of enhanced recovery techniques. There will also be an impact on the development of extensions to established and newly discovered heavy oil pools, as well as a major impact on development of bitumen resources. To assess the impact of horizontal drilling on heavy oil supply, high-impact and low-impact scenarios were evaluated under specified oil-price assumptions for four heavy oil areas in Saskatchewan and Alberta. Horizontal well potential for infill drilling, waterflood projects, and thermal projects was assessed and estimates were made of such developments as reserves additions and heavy oil development wells under the two scenarios. In the low case, projected supply of conventional heavy oil and bitumen stabilizes at a level in the 90,000-94,000 m 3 /d after 1994. In the high case, overall supply continuously grows from 80,000 m 3 /d in 1992 to 140,000 m 3 /d in 2002. Through application of horizontal drilling, reserves additions in western Canada could be improved by ca 100 million m 3 by 2002. 14 figs., 6 tabs

  17. Fire-fighting burning oil wells

    International Nuclear Information System (INIS)

    Newbury, Herbert; Risk, Stewart.

    1993-01-01

    A method of extinguishing burning oil wells is presented which involves dispensing liquid nitrogen to the burning site to prevent or inhibit oxygen from fuelling the flames. To carry out the method a remotely operated vehicle is described which is provided with a source of liquid nitrogen and an articulated deployment boom capable of supplying the liquid nitrogen to the site of a burning oil well. (Author)

  18. MARGINAL EXPENSE OIL WELL WIRELESS SURVEILLANCE MEOWS

    Energy Technology Data Exchange (ETDEWEB)

    Mason M. Medizade; John R. Ridgely; Donald G. Nelson

    2004-11-01

    A marginal expense oil well wireless surveillance system to monitor system performance and production from rod-pumped wells in real time from wells operated by Vaquero Energy in the Edison Field, Main Area of Kern County in California has been successfully designed and field tested. The surveillance system includes a proprietary flow sensor, a programmable transmitting unit, a base receiver and receiving antenna, and a base station computer equipped with software to interpret the data. First, the system design is presented. Second, field data obtained from three wells is shown. Results of the study show that an effective, cost competitive, real-time wireless surveillance system can be introduced to oil fields across the United States and the world.

  19. Oil wells and gas wells: aspects of radiological safety

    International Nuclear Information System (INIS)

    Soares, S.M.V.O.

    1987-01-01

    The objective of the present work is to present and analyse the main radiological protection problems associated with non destructive inspections of oil wells, with the view of minimizing the dose to members of the public living in nearby urban zones. Problems related to the surveillance of such activities and the need for well formulated procedures are also discussed based on specific Brasilian regulations. Finally, some examples of radiological accidents that have occured in urban zones are described including the methodology employed for the rescue of Iridium-192 sources and for the estimate of radiation doses for workers and general public. (author) [pt

  20. PDVSA INTEVEP Technologies in oil well drilling

    International Nuclear Information System (INIS)

    Bolivar, C.; Rafael, A.; Davila, Manuel A.

    1998-01-01

    The orimulsion, the generation of catalytic technologies and the development of HDH (process which transform heavy crudes in light crudes), are examples of some of the well known technologies developed by PDVSA INTEVEP. But the drilling oil wells technologies developed by the same entreprise, even though are very important, are less known all around the world. This document describes some products developed through those technologies: THIXOGAS T M which is an antimigratory aditive; INTEFLOW T M which is a fluid for drilling, complementation and rehabilitation of oil drills; INTERCAB T M which is an aditive for fluids in drilling; orimatita which is a denser for drilling fluids; CARBOLIG T M which is an aditive for drilling fluids; and many other products and technologies in development, impacted considerably the venezuelan economy by preserving the environment and saving quite an important amount of money in 1997 (Bs. 3.000 M M)

  1. Nuclear stimulation of oil-reservoirs

    International Nuclear Information System (INIS)

    Delort, F.; Supiot, F.

    1970-01-01

    Underground nuclear explosions in the Hoggar nuclear test site have shown that the geological effects may increase the production of oil or gas reservoirs. By studying the permanent liquid flow-rate with approximate DUPUIT's equation, or with a computer code, it is shown that the conventional well flow-rate may be increased by a factor between 3 and 50, depending on the medium and explosion conditions. (author)

  2. Nuclear stimulation of oil-reservoirs

    Energy Technology Data Exchange (ETDEWEB)

    Delort, F; Supiot, F [Commissariat a l' Energie Atomique, Centre d' Etudes de Bruyere-le-Chatel (France)

    1970-05-01

    Underground nuclear explosions in the Hoggar nuclear test site have shown that the geological effects may increase the production of oil or gas reservoirs. By studying the permanent liquid flow-rate with approximate DUPUIT's equation, or with a computer code, it is shown that the conventional well flow-rate may be increased by a factor between 3 and 50, depending on the medium and explosion conditions. (author)

  3. Kuwaiti oil wells blowout - aspects and effects

    International Nuclear Information System (INIS)

    Al-Jassim, F.

    1992-01-01

    When the Iraqi troops were forced to leave Kuwait, they left behind them the greatest oil catastrophe human beings have ever experienced. Fire plumes of tons of gases of principal pollutants, hydrocarbons, soot and associated metals were ejected up to a height of about 5 km. The retreating forces blew off about 1200 wells all over Kuwait fields. Of these 1200 wells, 614 are on fire. Four firefighting companies were hired to start work immediately after the liberation of Kuwaiti to control these wells. Three of these companies were from the U.S.A. and one from Canada. The number of these companies steadily increased along with logistical support. There are now 28 teams made up of private and multinational companies. This paper will concentrate on two main aspects. The first part will focus on the up-to-date engineering aspects of bringing the blown-out wells under control, focusing on oil well fires and the difficulties encountered, such as equipment availability, ordnance clearance and logistical support. The paper then describes the procedures used to control the wells, and the steps taken to reach this aim are presented. Finally the number of wells controlled, area-wise in different fields, with their original status, is also introduced. The second part will concentrate on the environmental aspects, covering the impact of the plumes on air quality, air pollution and health. The paper then discusses the effect on marine environment, vegetation and the soil. Finally, a forecast, conclusions and recommendations are presented. (author)

  4. Thermally stimulating mechanically-lifted well production

    Energy Technology Data Exchange (ETDEWEB)

    Richardson, E.A.; Hinson, R.A.

    1984-06-19

    A well which is producing slowly by artificial lift can be economically heated by first inflowing a nitrogen-generating solution, to form a pool of reacting liquid near the uppermost opening into the reservoir, then inflowing more solution while artificially-lifting liquid from near the lowermost opening into the reservoir at a rate substantially equalling the inflow rate.

  5. Alcorn wells bolster Philippines oil production

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This paper reports that Alcorn International Inc., Houston, is producing about 16,500 b/d of oil from West Linapacan A field in the South China Sea off the Philippines. The field's current production alone is more than fivefold the Philippines' total average oil flow of 3,000 b/d in 1991. It's part of a string of oil and gas strikes off Palawan Island that has made the region one of the hottest exploration/development plays in the Asia-Pacific theater

  6. Well performance relationships in heavy foamy oil reservoirs

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, R.; Mahadevan, J. [Society of Petroleum Engineers, Richardson, TX (United States)]|[Tulsa Univ., Tulsa, OK (United States)

    2008-10-15

    The viscosities and thermodynamic properties of heavy oils are different from conventional oils. Heavy oil reservoirs have foamy behaviour and the gas/oil interface stabilizes in the presence of asphaltenes. In the case of conventional oils, gas evolves from the solution when the formation pressure reaches the bubble point pressure. This study modelled the fluid properties of heavy foamy oils and their influence on the inflow performance relationship (IPR). An expression for inflow performance in heavy oil was developed by including the properties of foamy oil into a space averaged flow equation assuming pseudo-steady state conditions. The unique feature of this study was that the density, formation volume factor and solution gas-oil ratio were modelled as functions of entrained gas fraction. The newly developed expression for inflow performance of foamy oils may also be used to model conventional oil inflow by setting the entrained gas fraction to zero in the fluid property models. The results of the inflow performance of foamy oil and conventional oil were compared and an outflow performance relationship was calculated. The study showed that the inflow performance in foamy oil is influenced by entrained gas. The surface flow rates and bottom-hole flow rates are also influenced by the presence of entrained gas, with heavy foamy oil showing a higher volumetric production rate than conventional oil. The outflow performance curve depended on the fluid properties of the foamy oil. A nodal analysis of the well performance showed that the conventional calculation methods underestimate the production from foamy oil wells because they do not consider the effect of entrained gas which lowers density and improves the mobility of foamy oil. 14 refs., 2 tabs., 20 figs., 1 appendix.

  7. The environmental handling in the Oil Wells

    International Nuclear Information System (INIS)

    Carta Petrolera

    1998-01-01

    The oil industry bears environmental impacts related to the resources, soil, air, water, fauna and the socioeconomic aspects of the environment; for this reason the search of the petroleum goes beyond what is believed, it embraces other spheres because, after discovery, it is necessary to extract it, to transport it and to treat it to put it to the service of the humanity's development and in all this long and complex process, is the environmental responsibility, a serious concern as the same discovery of the hydrocarbons. In the beginnings of the oil industry in Colombia this activity was approached without the biggest forecasts as for contamination it refers; however, the environmental laws of the world and the constant concern to preserve the environment, it took to our country to the creation of severe legislations in the matter. In Colombia today in day an environmental legislation exists in all the related with the handling of waters, air and soils inside the oil activity

  8. An Independent Scientific Assessment of Well Stimulation in California Volume I

    Energy Technology Data Exchange (ETDEWEB)

    Long, Jane C.S. [California Council on Science and Technology, Sacramento, CA (United States); Feinstein, Laura C. [California Council on Science and Technology, Sacramento, CA (United States); Birkholzer, Jens [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Jordan, Preston [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Houseworth, James [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Dobson, Patrick F. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Heberger, Matthew [Pacific Inst., Oakland, CA (United States); Gautier, Donald L. [Dr. Donald Dautier, LLC., Palo Alto, CA (United States)

    2015-01-01

    In 2013, the California Legislature passed Senate Bill 4 (SB 4), setting the framework for regulation of well stimulation technologies in California, including hydraulic fracturing. SB 4 also requires the California Natural Resources Agency to conduct an independent scientific study of well stimulation technologies in California to assess current and potential future practices, including the likelihood that well stimulation technologies could enable extensive new petroleum production in the state, evaluate the impacts of well stimulation technologies and the gaps in data that preclude this understanding, identify risks associated with current practices, and identify alternative practices which might limit these risks. The study is issued in three volumes. This document, Volume I, provides the factual basis describing well stimulation technologies, how and where operators deploy these technologies for oil and gas production in California, and where they might enable production in the future. Volume II discusses how well stimulation affects water, the atmosphere, seismic activity, wildlife and vegetation, traffic, light and noise levels; it will also explore human health hazards, and identify data gaps and alternative practices. Volume III presents case studies to assess environmental issues and qualitative

  9. Radiotracer investigations in oil production and water injection wells

    International Nuclear Information System (INIS)

    Eapen, A.C.; Jain, S.K.; Kirti

    1977-01-01

    Injection of gamma emitting radiotracers into oil wells followed by logging provides information on several aspects such as the identification of zones of seepage of water in the water injection wells and also the location of source of water entering oil producting wells. The experience gained in the application of bromine-82 and rubidium-86 as radiotracers in such studies at the Ankleshwar and Kalol oil fields in Gujarat and Nazira in Assam has been briefly reported. (author)

  10. Chemical stimulation techniques for geothermal wells: experiments on the three-well EGS system at Soultz-sous-Forêts, France

    OpenAIRE

    Portier, Sandrine; Vuataz, François-David; Nami, Patrick; Sanjuan, Bernard; Gérard, André

    2012-01-01

    Rock matrix stimulation is a method of enhancing well production or injection within a broad range of challenging environments, varying from naturally fractured limestones to sandstones with complex mineralogy. A common and often successful stimulation option, matrix acidizing, utilizes acids that react and remove mineral phases restricting fluid flow. Reviewed is the technology of chemical treatments available for oil, gas and geothermal wells and the key elements and results of the chemical...

  11. Feasibility study for the installation of a nuclear reactor in thermal stimulation processes in heavy oil extraction from Orinoco oil belt

    International Nuclear Information System (INIS)

    Munoz, A.; Sanchez, R.

    1982-01-01

    Due to strategic need in the exploitation of heavy and extraheavy oil wells of Orinoco oil belt, technical and economical studies have been carried out to determine an optimal method for oil production and exploitation. So far, studies indicate thermal stimulation is the most adequate technique. Experience shows that stimulation cost is high when traditional methods (boilers) are used. The profit is due to the high price of oil in international market. Due to actual oil price trends, evaluation of nontraditional methods to generate steam in thermal stimulation processes (steam injection) is in order. A nuclear reactor as steam generator was evaluated. It was found economical feasibility and saving in fuel cost between 31.08% and 72.63% depending on oil prices

  12. Feasibility of oil recovery by chemical flooding through horizontal wells

    Energy Technology Data Exchange (ETDEWEB)

    El-Abbas, A.M.; El-Sallaly, M. E.; Sayyouh, M. H.; El-Batanony, M. H.; Darwich, T. M.; Desouky, S. M. [Cairo Univ (Egypt)

    1998-12-31

    Crude oil production in the Gulf of Suez by polymer, surfactant, and surfactant/polymer flooding from a horizontal well in a scaled five-spot sandpacked model was studied. The suitability of the enhanced oil recovery predictive models, developed by the U.S. Department of Energy, was investigated for their ability to predict the experimental data and to assess the feasibility of oil recovery by chemical flooding. Good agreement was found between the predicted and experimental values. Experimental results showed that oil recovery was significantly affected by the physical properties of the crude oil and chemical solutions; that oil recovery was higher for a polymer flooding than for a surfactant flooding operation; and that oil recovery was improved by increasing the perforated length ratio up to a value of 0.81. A tendency for oil recovery to decrease was observed when the horizontal well was positioned below or above the central axis path of the formation at the advanced injection stages; and oil recovery by surfactant or polymer flooding was significantly affected by the onset timing of the surfactant or polymer slug injection. The oil-water bank stability in surfactant and polymer flooding processes was found to be dependent on slug size and slug injection time. 23 refs., 1 tab., 17 figs.

  13. Prediction of temperature profile in oil wells

    International Nuclear Information System (INIS)

    Laderion, A.

    2000-01-01

    A mathematical model has been developed to predict the temperature distribution in well bores either offshore or inshore. It is incorporate the different activities encountered during drilling operations. Furthermore, the effect of drill collar and casings and bit rotating in a well during completion has been considered. The two dimensional approach is presented in the form of a computer program which is adopted for solution of the finite difference equations describing the heat transmission in the well bore in the form of a direct solution technique. The power law model has been selected for drilling mud and its indices have been calculated. Comparing measured data, recorded for a period of 82 hours during different activities in a drilling operation for 15/20 A-4, an exploration well in the Central North Sea with calculated results, show there is a good agreement between the prediction and measured temperatures in the well bore

  14. Modeling of well drilling heating on crude oil using microwave

    Energy Technology Data Exchange (ETDEWEB)

    Muntini, Melania Suweni, E-mail: melania@physics.its.ac.id; Pramono, Yono Hadi; Yustiana [Physics Department, Institut Teknologi Sepuluh Nopember, Surabaya Kampus ITS, Sukolilo, Surabaya 60111 (Indonesia)

    2016-03-11

    As the world’s oil reserves are dwindling, some researchers have been prompted to make a breakthrough to further improve the efficiency of exploration and production. One of the technologies used is heating the crude oil. This paper presents the modeling results of heat treatment on crude oil using microwave energy. Modeling is conducted by assuming that the diameter of the well is 11,16 cm, the heat source is applied on the surface of the well, and the cut-off frequency in the air and on crude oil are 1,56 GHz. and 0.91 GHz, respectively. The energy generated by the microwave radiation is converted into heat energy which is absorbed by the crude oil. Consequently, this energy increases the temperature of crude oil through a heat transfer mechanism. The results obtained showed that the temperature of crude oil is about 200°C at a depth of 62.5cm, and at a distance of 3 cm from the center of the well. Temperature along the well follows an exponential function, which is from the center of the well in the direction radially outward from the cylinder axis. It has been observed that the temperature decreases as measured from the well surface along the cylinder.

  15. Radiation incident in oil well logging

    International Nuclear Information System (INIS)

    Lozada, J.A.

    1998-01-01

    On June 4th 1997 equipment failure and violation of approved procedures by a crew of workers initiated a series of events that resulted in the unnecessary exposure to neutron and gamma radiation, from a 666 GBq Am 241 Be source, of forty two workers from a well logging company in Venezuela. Due to the presence of dry mud or drilling fluids inside the logging tool, the nosepiece was screwed off the rest of the source holder; this piece was mistaken for the entire source holder thus leaving the source inside the tool. The tool was labelled for maintenance and electronic laboratory personal worked near the source for seven hours before they identify its presence. As soon as the incident was detected a contingency plan was implemented and the source could be retrieved from the tool and placed in its shipping container. The TLD badges indicate doses well below the annual limit of 20 mSv, and none of the workers involved in the incident seem to show serious health consequences from it. After the incident, in order to avoid the occurrence of similar situations, a better source and tool maintenance program was implemented, all the workers were re-trained, and area monitors were installed in all operations bases. (author)

  16. Review of Well Operator Files for Hydraulically Fractured Oil and Gas Production Wells: Well Design and Construction Fact Sheet

    Science.gov (United States)

    EPA reviewed a statistically representative sample of oil and gas production wells reported by nine service companies to help understand the role of well design and construction practices preventing pathways for subsurface fluid movement.

  17. Geospatial Analysis of Oil and Gas Wells in California

    Science.gov (United States)

    Riqueros, N. S.; Kang, M.; Jackson, R. B.

    2015-12-01

    California currently ranks third in oil production by U.S. state and more than 200,000 wells have been drilled in the state. Oil and gas wells provide a potential pathway for subsurface migration, leading to groundwater contamination and emissions of methane and other fluids to the atmosphere. Here we compile available public databases on oil and gas wells from the California Department of Conservation's Division of Oil, Gas, and Geothermal Resources, the U.S. Geological Survey, and other state and federal sources. We perform geospatial analysis at the county and field levels to characterize depths, producing formations, spud/completion/abandonment dates, land cover, population, and land ownership of active, idle, buried, abandoned, and plugged wells in California. The compiled database is designed to serve as a quantitative platform for developing field-based groundwater and air emission monitoring plans.

  18. Oil and Natural Gas Wells, US, 2010, Platts

    Data.gov (United States)

    U.S. Environmental Protection Agency — The Oil and Natural Gas Well geospatial dataset contains point features representing permitted locations, most of which have been drilled and completed, or drilled...

  19. Cement for Oil Well Cementing Operations in Ghana

    African Journals Online (AJOL)

    Michael

    For Portland cement to qualify as oil well cement, the chemical and physical properties must meet ..... Reservoir Engineering, Stanford University,. Stanford, California, pp. ... Construction”, PhD Thesis, Kwame Nkrumah. University of Science ...

  20. Oil, Gas, and Injection Wells in Louisiana, Geographic NAD83, LDNR (2007) [oil_gas_wells_LDNR_2007

    Data.gov (United States)

    Louisiana Geographic Information Center — This is a point dataset containing the location of over 230,000 oil and gas and injection wells in the state of Louisiana. It was developed from the DNR Office of...

  1. An Independent Scientific Assessment of Well Stimulation in California Volume II

    Energy Technology Data Exchange (ETDEWEB)

    Long, Jane C.S. [California Council on Science and Technology, Sacramento, CA (United States); Feinstein, Laura C. [California Council on Science and Technology, Sacramento, CA (United States); Bachmann, Corinne E. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Birkholzer, Jens T. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Camarillo, Mary Kay [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Domen, Jeremy K. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Foxall, William [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Houseworth, James [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Jin, Ling [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Jordan, Preston D. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Maddalena, Randy L. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); McKone, Thomas E. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Millstein, Dev E. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Reagan, Matthew T. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Sandelin, Whitney L. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Stringfellow, William T. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Varadharajan, Charuleka [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Cooley, Heather [Pacific Inst., Oakland, CA (United States); Donnelly, Kristina [Pacific Inst., Oakland, CA (United States); Heberger, Matthew G. [Pacific Inst., Oakland, CA (United States); Hays, Jake [PSE Healthy Energy, Berkeley, CA (United States); Shonkoff, Seth B.C. [PSE Healthy Energy, Berkeley, CA (United States); Brandt, Adam [Stanford Univ., CA (United States); Englander, Jacob G. [Stanford Univ., CA (United States); Hamdoun, Amro [Univ. of California of San Diego, La Jolla, CA (United States); Nicklisch, Sascha C.T. [Univ. of California of San Diego, La Jolla, CA (United States); Harrison, Robert J. [Univ. of California, San Francisco, CA (United States); Wettstein, Zachary S. [Univ. of California, San Francisco, CA (United States); Banbury, Jenner [California State Univ. Stanislaus, Turlock, CA (United States); Cypher, Brian L. [California State Univ. Stanislaus, Turlock, CA (United States); Phillips, Scott E. [California State Univ. Stanislaus, Turlock, CA (United States)

    2015-07-01

    This study is issued in three volumes. Volume I, issued in January 2015, describes how well stimulation technologies work, how and where operators deploy these technologies for oil and gas production in California, and where they might enable production in the future. Volume II, the present volume, discusses how well stimulation could affect water, atmosphere, seismic activity, wildlife and vegetation, and human health. Volume II reviews available data, and identifies knowledge gaps and alternative practices that could avoid or mitigate these possible impacts. Volume III, also issued in July 2015, presents case studies that assess environmental issues and qualitative risks for specific geographic regions. A final Summary Report summarizes key findings, conclusions and recommendations of all three volumes.

  2. An Independent Scientific Assessment of Well Stimulation in California Volume III

    Energy Technology Data Exchange (ETDEWEB)

    Long, Jane C.S. [California Council on Science and Technology, Sacramento, CA (United States); Feinstein, Laura C. [California Council on Science and Technology, Sacramento, CA (United States); Birkholzer, Jens [California Council on Science and Technology, Sacramento, CA (United States); Foxall, William [California Council on Science and Technology, Sacramento, CA (United States); Houseworth, James [California Council on Science and Technology, Sacramento, CA (United States); Jordan, Preston [California Council on Science and Technology, Sacramento, CA (United States); Lindsey, Nathaniel [California Council on Science and Technology, Sacramento, CA (United States); Maddalena, Randy [California Council on Science and Technology, Sacramento, CA (United States); McKone, Thomas [California Council on Science and Technology, Sacramento, CA (United States); Stringfellow, William [California Council on Science and Technology, Sacramento, CA (United States); Ulrich, Craig [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Heberger, Matthew [Pacific Inst., Oakland, CA (United States); Shonkoff, Seth [PSE Healthy Energy, Berkeley, CA (United States); Brandt, Adam [Stanford Univ., CA (United States); Ferrar, Kyle [The FracTracker Alliance, Oakland, CA (United States); Gautier, Donald [DonGautier LLC., Palo Alto, CA (United States); Phillips, Scott [California State Univ. Stanislaus, Turlock, CA (United States); Greenfield, Ben [Univ. of California, Berkeley, CA (United States); Jerrett, Michael L.B. [Univ. of California, Los Angeles, CA (United States)

    2015-07-01

    This study is issued in three volumes. Volume I, issued in January 2015, describes how well stimulation technologies work, how and where operators deploy these technologies for oil and gas production in California, and where they might enable production in the future. Volume II, issued in July 2015, discusses how well stimulation could affect water, atmosphere, seismic activity, wildlife and vegetation, and human health. Volume II reviews available data, and identifies knowledge gaps and alternative practices that could avoid or mitigate these possible impacts. Volume III, this volume, presents case studies that assess environmental issues and qualitative risks for specific geographic regions. The Summary Report summarizes key findings, conclusions and recommendations of all three volumes.

  3. Anomalies in oil and water wells and the Tangshan earthquake

    Energy Technology Data Exchange (ETDEWEB)

    Wang, W.

    1980-01-01

    Bin County, Shandong Province, has a complicated fault structure resulting from the interaction of a number of fault blocks. An examination of the behavior of oil wells in various oilfields located in faulting areas showed anomalies in 7 of them related to the Tangshan earthquake. Three wells (Nos. 88, 101, and 102) showed sharp peaks in output within a month before the earthquake. One well (No. 278) showed a sharp peak in the oil-gas ratio in April and July of 1976. There was a sharp increase in the water content of the oil produced by one well (No. 285) in July. Finally, one well (4-Xi4-10) showed a decrease in the rate of change of static pressure, starting in March 1976 and achieving a plateau in June which persisted until October before the static pressure again began to change more rapidly.

  4. Performance of high-rate gravel-packed oil wells

    Energy Technology Data Exchange (ETDEWEB)

    Unneland, Trond

    2001-05-01

    Improved methods for the prediction, evaluation, and monitoring of performance in high-rate cased-hole gravel-packed oil wells are presented in this thesis. The ability to predict well performance prior to the gravel-pack operations, evaluate the results after the operation, and monitor well performance over time has been improved. This lifetime approach to performance analysis of gravel-packed oil wells contributes to increase oil production and field profitability. First, analytical models available for prediction of performance in gravel-packed oil wells are reviewed, with particular emphasis on high-velocity flow effects. From the analysis of field data from three North Sea oil fields, improved and calibrated cased-hole gravel-pack performance prediction models are presented. The recommended model is based on serial flow through formation sand and gravel in the perforation tunnels. In addition, new correlations for high-velocity flow in high-rate gravel-packed oil wells are introduced. Combined, this improves the performance prediction for gravel-packed oil wells, and specific areas can be targeted for optimized well design. Next, limitations in the current methods and alternative methods for evaluation and comparison of well performance are presented. The most widely used parameter, the skin factor, remains a convenient and important parameter. However, using the skin concept in direct comparisons between wells with different reservoir properties may result in misleading or even invalid conclusions. A discussion of the parameters affecting the skin value, with a clarification of limitations, is included. A methodology for evaluation and comparison of gravel-packed well performance is presented, and this includes the use of results from production logs and the use of effective perforation tunnel permeability as a parameter. This contributes to optimized operational procedures from well to well and from field to field. Finally, the data sources available for

  5. Sleeving-back of horizontal wells to control downstream oil saturation and improve oil recovery

    Energy Technology Data Exchange (ETDEWEB)

    Greaves, M.; Saghr, A. M. [Bath Univ (United Kingdom)

    1998-12-31

    Air injection has become popular as an enhanced recovery technology, applicable over a wide variety of reservoir conditions including heavy, medium and light oils. One problem observed in light oil reservoirs is the tendency to desaturate the oil layer downstream of the moving front. This is particularly common in the case of thermal recovery processes. In this experiment designed to study ways to restrict the de-saturation of the oil layer, a modified horizontal producer well, incorporating a `sleeve-back` principal was used. The objective was to replicate the `toe-to-heel` displacement process occurring during heavy oil recovery, wherein downstream oil is essentially immobile due to its high viscosity. The `sleeve-back` of the well was achieved using a co-aligned, two-well assembly, so that the upstream section of the horizontal producer well was active, and continuously adjusted during propagation of the combustion front. The use of this continuous `sleeve-back` operation to control the level of de-saturation in the downstream section of a sand pack was successful as confirmed by the very high oil recovery achieved, equivalent to 93.5 per cent of oil in place. The level of CO{sub 2} production was also very high. The `sleeve-back` of the horizontal producer well made the light oil in-situ combustion more efficient compared to what would be expected in a fully-open well. The `sleeve-back` of the well also produced thermal contours in the sand pack that closely resembled those observed with heavy, highly viscous oil. By sealing-off the otherwise open well in the downstream part of the reservoir, the de-saturation of the oil layer was prevented. 9 refs., 4 tabs., 9 figs.

  6. The tidal influence on oil and gas emissions from an abandoned oil well: Nearshore Summerland, California

    International Nuclear Information System (INIS)

    Leifer, Ira; Wilson, Ken

    2007-01-01

    Oil and gas emissions were quantified for natural and human sources in nearshore waters off Summerland, California through deployment of custom designed collection tents. Seepage was measured at a repeatedly abandoned well, on the seabed from a caisson located along the historical location of the Treadwell Wharf, where the world's first off-shore oil wells were drilled at the end of the 19th century. Seepage rates at the capped T-10 Well, located in ∼5 m water, showed high correlation to tides. Site emissions were 2.4 and 38.7 L day -1 oil and gas, respectively. Emissions were measured from two areas of seepage at the T-10 Well Site. Oil and gas ratios were inversely correlated between the two seepage areas, demonstrating connectivity. Data were interpreted in terms of an electronic circuit model of seepage with respect to the time lag between local low tide and peak oil emissions

  7. Composite Coiled Tubing for Extended Reach in Horizontal Oil Wells

    DEFF Research Database (Denmark)

    Costache, Andrei; Berggreen, Christian

    2017-01-01

    Conventional steel coiled tubing cannot reach along the entire length of very long horizontal oil wells. A lighter and more buoyant coiled tube is made possible using composite materials. The high stiffness to weight ratio of fiber reinforced polymers, coupled with a lower coefficient of friction......, has the potential of greatly extending the reach in horizontal oil wells. This study shows how to design composite coiled tubing and gives a comprehensive discussion about the most influential parameters. Several solutions, using glass-fiber and carbon are considered. Finite element models are used...

  8. Auto Detection For High Level Water Content For Oil Well

    Science.gov (United States)

    Janier, Josefina Barnachea; Jumaludin, Zainul Arifin B.

    2010-06-01

    Auto detection of high level water content for oil well is a system that measures the percentage of water in crude oil. This paper aims to discuss an auto detection system for measuring the content of water level in crude oil which is applicable for offshore and onshore oil operations. Data regarding water level content from wells can be determined by using automation thus, well with high water level can be determined immediately whether to be closed or not from operations. Theoretically the system measures the percentage of two- fluid mixture where the fluids have different electrical conductivities which are water and crude oil. The system made use of grid sensor which is a grid pattern like of horizontal and vertical wires. When water occupies the space at the intersection of vertical and horizontal wires, an electrical signal is detected which proved that water completed the circuit path in the system. The electrical signals are counted whereas the percentage of water is determined from the total electrical signals detected over electrical signals provided. Simulation of the system using the MultiSIM showed that the system provided the desired result.

  9. Ecological and technical situation of flooded oil wells in Kazakhstan

    International Nuclear Information System (INIS)

    Kuterbekov, K. A.; Kabdrakhimova, G. D.; Nurakhmetov, T. N.; Zhaksigulova, A.; Nukenov, D. N.; Kushkimbaev, B. M.; Nurmukhanbetova, A. K.

    2012-01-01

    The data of ecological and technical condition of flooded and inundated wells in Atyrau and Mangystau regions of the West of Kazakhstan is given in this abstract. There is necessary to elaborate methods for liquidation, individual plans of conservations, to produce isolating and liquidation procedures on wells and to estimate environment effects. Also we will provide for estimation technical condition of conservation oil wells on territory of flooded by Caspian sea. (Authors)

  10. Stimulation of diesel degradation and biosurfactant production by aminoglycosides in a novel oil-degrading bacterium Pseudomonas luteola PRO23

    Directory of Open Access Journals (Sweden)

    Atanasković Iva M.

    2016-01-01

    Full Text Available Bioremediation is promising technology for dealing with oil hydrocarbons contamination. In this research growth kinetics and oil biodegradation efficiency of Pseudomonas luteola PRO23, isolated from crude oil-contaminated soil samples, were investigated under different concentrations (5, 10 and 20 g/L of light and heavy crude oil. More efficient biodegradation and more rapid adaptation and cell growth were obtained in conditions with light oil. The 5 to 10 g/L upgrade of light oil concentration stimulated the microbial growth and the biodegradation efficiency. Further upgrade of light oil concentration and the upgrade of heavy oil concentration both inhibited the microbial growth, as well as biodegradation process. Aminoglycosides stimulated biosurfactant production in P. luteola in the range of sub-inhibitory concentrations (0.3125, 0.625 μg/mL. Aminoglycosides also induced biofilm formation. The production of biosurfactants was the most intense during lag phase and continues until stationary phase. Aminoglycosides also induced changes in P. luteola growth kinetics. In the presence of aminoglycosides this strain degraded 82% of diesel for 96 h. These results indicated that Pseudomonas luteola PRO23 potentially can be used in bioremediation of crude oil-contaminated environments and that aminoglycosides could stimulate this process. [Projekat Ministarstva nauke Republike Srbije, br. TR31080

  11. Dalhart's only Permian field gets best oil well

    International Nuclear Information System (INIS)

    Land, R.

    1992-01-01

    This paper reports that activity is picking up in Proctor Ranch oil field in the northwestern Texas panhandle, the only Permian producing field in the lightly drilled Dalhart basin. During the last 2 1/2 months, the field has a new operator and a new producing well, the best of five drilled since discovery in 1990. Corlena Oil Co., Amarillo, acquired the field from McKinney Oil Co. in May and tested its first well in early July. The 1-64 Proctor, 18 miles west of Channing, pumped at rates as high as 178 bd of oil and 6 b/d of water from Permian Wolfcamp dolomite perforations at 4,016-29 ft. Corlena plans to drill another well south of the field soon. The lease requires that the next well be spudded by early November. The field appears to be combination structural-stratigraphic trap in which the dolomite pinches out against the Bravo Domes-Oldham nose to the west

  12. Use of surfactants in cleaning paraffin from oil wells

    Energy Technology Data Exchange (ETDEWEB)

    Liebold, G; Rehberg, W

    1969-05-01

    The use of surfactants is described especially oxethylated alkylphenols, in the cleaning of oil wells from paraffin. Aqueous 1 or 10% solutions of the surfactant were injected into the well through the annulus, partially in combination with demulsifiers (for example Separol-brands of BASF). Injection was accomplished continuously or in intervals; in the beginning of 50 ppm surfactant, afterward 15 to 30 ppm as related to the wet crude was necessary. Efficiency of the treatment could be proved by the decrease of pressure in the pipes, the loosening of paraffin shells, and considerably prolonged operation periods in wells which otherwise would have come to a standstill. In quite a number of wells, treatment with hot oil and electric heating could be completely replaced by injection of surfactants. (11 refs.)

  13. Monte Carlo Simulations of Neutron Oil well Logging Tools

    International Nuclear Information System (INIS)

    Azcurra, Mario

    2002-01-01

    Monte Carlo simulations of simple neutron oil well logging tools into typical geological formations are presented.The simulated tools consist of both 14 MeV pulsed and continuous Am-Be neutron sources with time gated and continuous gamma ray detectors respectively.The geological formation consists of pure limestone with 15% absolute porosity in a wide range of oil saturation.The particle transport was performed with the Monte Carlo N-Particle Transport Code System, MCNP-4B.Several gamma ray spectra were obtained at the detector position that allow to perform composition analysis of the formation.In particular, the ratio C/O was analyzed as an indicator of oil saturation.Further calculations are proposed to simulate actual detector responses in order to contribute to understand the relation between the detector response with the formation composition

  14. Monte Carlo simulations of neutron oil well logging tools

    International Nuclear Information System (INIS)

    Azcurra, Mario O.; Zamonsky, Oscar M.

    2003-01-01

    Monte Carlo simulations of simple neutron oil well logging tools into typical geological formations are presented. The simulated tools consist of both 14 MeV pulsed and continuous Am-Be neutron sources with time gated and continuous gamma ray detectors respectively. The geological formation consists of pure limestone with 15% absolute porosity in a wide range of oil saturation. The particle transport was performed with the Monte Carlo N-Particle Transport Code System, MCNP-4B. Several gamma ray spectra were obtained at the detector position that allow to perform composition analysis of the formation. In particular, the ratio C/O was analyzed as an indicator of oil saturation. Further calculations are proposed to simulate actual detector responses in order to contribute to understand the relation between the detector response with the formation composition. (author)

  15. Maximizing probable oil field profit: uncertainties on well spacing

    International Nuclear Information System (INIS)

    MacKay, J.A.; Lerche, I.

    1997-01-01

    The influence of uncertainties in field development costs, well costs, lifting costs, selling price, discount factor, and oil field reserves are evaluated for their impact on assessing probable ranges of uncertainty on present day worth (PDW), oil field lifetime τ 2/3 , optimum number of wells (OWI), and the minimum (n-) and maximum (n+) number of wells to produce a PDW ≥ O. The relative importance of different factors in contributing to the uncertainties in PDW, τ 2/3 , OWI, nsub(-) and nsub(+) is also analyzed. Numerical illustrations indicate how the maximum PDW depends on the ranges of parameter values, drawn from probability distributions using Monte Carlo simulations. In addition, the procedure illustrates the relative importance of contributions of individual factors to the total uncertainty, so that one can assess where to place effort to improve ranges of uncertainty; while the volatility of each estimate allows one to determine when such effort is needful. (author)

  16. Modeling thermal stress propagation during hydraulic stimulation of geothermal wells

    Science.gov (United States)

    Jansen, Gunnar; Miller, Stephen A.

    2017-04-01

    A large fraction of the world's water and energy resources are located in naturally fractured reservoirs within the earth's crust. Depending on the lithology and tectonic history of a formation, fracture networks can range from dense and homogeneous highly fractured networks to single large scale fractures dominating the flow behavior. Understanding the dynamics of such reservoirs in terms of flow and transport is crucial to successful application of engineered geothermal systems (also known as enhanced geothermal systems or EGS) for geothermal energy production in the future. Fractured reservoirs are considered to consist of two distinct separate media, namely the fracture and matrix space respectively. Fractures are generally thin, highly conductive containing only small amounts of fluid, whereas the matrix rock provides high fluid storage but typically has much smaller permeability. Simulation of flow and transport through fractured porous media is challenging due to the high permeability contrast between the fractures and the surrounding rock matrix. However, accurate and efficient simulation of flow through a fracture network is crucial in order to understand, optimize and engineer reservoirs. It has been a research topic for several decades and is still under active research. Accurate fluid flow simulations through field-scale fractured reservoirs are still limited by the power of current computer processing units (CPU). We present an efficient implementation of the embedded discrete fracture model, which is a promising new technique in modeling the behavior of enhanced geothermal systems. An efficient coupling strategy is determined for numerical performance of the model. We provide new insight into the coupled modeling of fluid flow, heat transport of engineered geothermal reservoirs with focus on the thermal stress changes during the stimulation process. We further investigate the interplay of thermal and poro-elastic stress changes in the reservoir

  17. OIL WELL REMEDIATION IN CLAY AND WAYNE COUNTIES, IL

    Energy Technology Data Exchange (ETDEWEB)

    Peter L. Dakuras; Larry Stieber; Dick Young

    2003-07-09

    This is the second progress and final technical report of the remediation of abandoned wells in Clay and Wayne Counties in Illinois. The wells will be identified as the Routt No.3 and No.4 and the Bates Hosselton 1 and 2. Both sites have met all legal, financial and environmental requirements to drill and/or pump oil on both leases. We have also obtained all available information about both leases. All steps were taken to improve access roads, dig the necessary pits, and build the necessary firewalls. This progress and final technical report will address the remediation efforts as well as our results and conclusions.

  18. Oil flow in the oil well tube annulus of vertical bearing assemblies (leakage)

    International Nuclear Information System (INIS)

    Piao, Yinghu

    1997-01-01

    A numerical simulation and experimental flow visualization study was conducted to better understand oil well leakage, particularly in the annular clearance space surrounding the oil well tube. A test rig was developed to simulate the bearing's oil well tube annulus. A major feature of this rig was to allow visual access to the annular clearance space and to the region beneath the rotating runner where strong secondary flow effects are known to exist. The main method for tracing the secondary flow pathlines was a light sheet visualization technique using micro air bubbles as the tracer. The effect of runner speed on the pathlines was studied. The velocity of the oil flow was measured experimentally and the results were compared with numerical data. A numerical technique was developed to trace the micro air bubbles in the oil flow field using a three dimensional CFD code for laminar, axisymmetric flow with a free surface. The buoyancy effects of gravitational and centrifugal forces were considered when determining the pathline of air bubbles. Bubble size, oil viscosity and runner speed were some of the parameters that affect the path of the air bubbles

  19. Steam heating of local well bore area in light crude oil horizons

    Energy Technology Data Exchange (ETDEWEB)

    Mikerin, B P

    1968-02-01

    Beneficial results were obtained from a series of small steam injection treatments of oil producing wells in Asfaltov field. In this field, spacing between producing wells is 200 m, well depth is about 450 m, formation temperature is 27$C, oil gravity is 0,845 g/cu cm, and oil viscosity is 6-10 Hz. In every treatment, 200 g of ''disolvan'' was added per ton of steam, to minimize clay swelling in the formation. Form treatment results it is concluded that: (1) steam stimulation gives positive results 65% of the time; (2) best results were obtained in compact sand formations, 5-6 m thick; (3) positive results last up to one yr after steam soak; (4) with repeated treatments oil production increases 1.5-2 times; (5) temperature of steam during flow from wellhead to well bottom at 350 m, is decreased by 25%; and (6) about 1.3 million kcal were used per 1 m of net sand thickness.

  20. Nuclear cross section library for oil well logging analysis

    International Nuclear Information System (INIS)

    Kodeli, I.; Kitsos, S.; Aldama, D.L.; Zefran, B.

    2003-01-01

    As part of the IRTMBA (Improved Radiation Transport Modelling for Borehole Applications) Project of the EU Community's 5 th Programme a special purpose multigroup cross section library to be used in the deterministic (as well as Monte Carlo) oil well logging particle transport calculations was prepared. This library is expected to improve the prediction of the neutron and gamma spectra at the detector positions of the logging tool, and their use for the interpretation of the neutron logging measurements was studied. Preparation and testing of this library is described. (author)

  1. A New Well Classification Scheme For The Nigerian Oil Industry

    International Nuclear Information System (INIS)

    Ojoh, K.

    2002-01-01

    Oil was discovered in the Niger Delta Basin in 1956, with Oloibiri 1, after 21 wildcats had been drilled with lack of success. In the 46 years since, 25 companies have discovered 52 Billion barrels, of which 20 Billion has been produced, leaving proven reserves of 32 Billion Barrels.Between now and 2010, the country would like to add 15 billion barrels of oil to these reserves. The target is 40 Billion barrels. The National aspiration is to be able to obtain OPEC quota to produce 4 million barrels of oil per day. A large percentage of the reserves additions will definitely come from the deepwater segment of the basin, where fields of over 500 Million barrels are expected. Exploration also continues on the shelf and on land, but the rate of discovery in these areas is - after 46 years of constant effort - constrained by the relative maturity of the basin.The challenges are that few, small, untested structures remain on shelf and land, whereas most undiscovered reserves are in stratigraphic accumulations within known producing areas. These are only visible on 3-D seismic after it is processed using state-of-the-art, high-technology attribute analyses. In the deepwater province, the stratigraphy throws up problems of reservoir continuity. Channels and lobe fans have complex spatial distribution which systematically require more than the classical two appraisal wells in conventional classification.The industry agrees that the current well classification scheme, which came into place in 1977, needs to be overhauled to take cognisance of these challenges.At a workshop last May, a Well Classification Committee comprising members from OPTS, DEWOG, NAIPEC as well as the DPR was mandated to produce a well classification scheme for the industry. This paper examines the current scheme and comes with a technically sound, widely accepted alternative, complete with exhaustive illustrations

  2. Utilization of oil wells for electricity generation: Performance and economics

    International Nuclear Information System (INIS)

    Kharseh, Mohamad; Al-Khawaja, Mohammed; Hassani, Ferri

    2015-01-01

    There is a general agreement that the climate change, which is the most important challenge facing humanity, is anthropogenic and attributed to fossil fuel consumption. Therefore, deploying more renewable energy resources is an urgent issue to be addressed. Geothermal refers to existing heat energy in deep rock and sedimentary basins. Traditionally, geothermal energy has been exploited in places with plentiful hot water at relatively shallow depth. Unfortunately, the high exploration and drilling costs of boreholes is the main barrier to the commerciality of geothermal worldwide. In oil producing countries, such problems can be overcome by utilizing oil or gas wells. The current study presents thermodynamic and economic analyses of a binary geothermal power generation system for commercial electricity generation. Two different source temperatures (100 and 120 °C) and constant sink temperature (29 °C) were considered. The optimal working fluid and optimal design that improve the performance of the plant are determined. For the current costs in Qatar, the economical analysis of 5 MW geothermal plant shows that the levelized cost of electricity for the plant varies from 5.6 to 5.2 ¢/kW. Whereas, the payback period of such plants lies between 5.8 and 4.8 years. - Highlights: • Utilizing oil well makes geothermal plant competitive with other resources. • R32 seems to be the best working fluid. • The levelized cost of electricity for geothermal plant is less than 5.6 ¢/kWh. • The payback time of geothermal plant is less than 6 years.

  3. Tragacanth gum: an effective oil well drilling fluid additive

    Energy Technology Data Exchange (ETDEWEB)

    Mahto, V.; Sharma, V. [Indian School of Mines, Dhanbad (India). Department of Petroleum Engineering

    2005-02-15

    The low penetration rate, excessive torque and drag, poor hole cleaning and formation damage are major impediments in drilling oil and gas well. These have a major impact on drilling efficiency and well economics. Keeping these in mind, an attempt was made to design a water based drilling fluid system using Indian bentonite clays and tragacanth gum. The effect of tragacanth gum on rheological behavior of three different Indian bentonite water suspensions was studied and a drilling fluid system was developed. The filtrates of these drilling fluids were subjected to formation damage study on the field core using Ruska Liquid Permeameter. The laboratory investigation furnishes that tragacanth gum acts as a good viscosifier and fluid loss control agent. The drilling fluid filtrate also has less effect on formation damage. (author)

  4. Productivity Analysis of Volume Fractured Vertical Well Model in Tight Oil Reservoirs

    Directory of Open Access Journals (Sweden)

    Jiahang Wang

    2017-01-01

    Full Text Available This paper presents a semianalytical model to simulate the productivity of a volume fractured vertical well in tight oil reservoirs. In the proposed model, the reservoir is a composite system which contains two regions. The inner region is described as formation with finite conductivity hydraulic fracture network and the flow in fracture is assumed to be linear, while the outer region is simulated by the classical Warren-Root model where radial flow is applied. The transient rate is calculated, and flow patterns and characteristic flowing periods caused by volume fractured vertical well are analyzed. Combining the calculated results with actual production data at the decline stage shows a good fitting performance. Finally, the effects of some sensitive parameters on the type curves are also analyzed extensively. The results demonstrate that the effect of fracture length is more obvious than that of fracture conductivity on improving production in tight oil reservoirs. When the length and conductivity of main fracture are constant, the contribution of stimulated reservoir volume (SRV to the cumulative oil production is not obvious. When the SRV is constant, the length of fracture should also be increased so as to improve the fracture penetration and well production.

  5. Bluebell Field, Uinta Basin: reservoir characterization for improved well completion and oil recovery

    Science.gov (United States)

    Montgomery, S.L.; Morgan, C.D.

    1998-01-01

    Bluefield Field is the largest oil-producing area in the Unita basin of northern Utah. The field inclucdes over 300 wells and has produced 137 Mbbl oil and 177 bcf gas from fractured Paleocene-Eocene lacustrine and fluvial deposits of the Green River and Wasatch (Colton) formations. Oil and gas are produced at depths of 10 500-13 000 ft (3330-3940 m), with the most prolific reservoirs existing in over-pressured sandstones of the Colton Formation and the underlying Flagstaff Member of the lower Green River Formation. Despite a number of high-recovery wells (1-3 MMbbl), overall field recovery remains low, less than 10% original oil in place. This low recovery rate is interpreted to be at least partly a result of completion practices. Typically, 40-120 beds are perforated and stimulated with acid (no proppant) over intervals of up to 3000 ft (900 m). Little or no evaluation of individual beds is performed, preventing identification of good-quality reservoir zones, water-producing zones, and thief zones. As a result, detailed understanding of Bluebell reservoirs historically has been poor, inhibiting any improvements in recovery strategies. A recent project undertaken in Bluebell field as part of the U.S. Department of Energy's Class 1 (fluvial-deltaic reservoir) Oil Demonstration program has focused considerable effort on reservoir characterization. This effort has involved interdisciplinary analysis of core, log, fracture, geostatistical, production, and other data. Much valuable new information on reservoir character has resulted, with important implications for completion techniques and recovery expectations. Such data should have excellent applicability to other producing areas in the Uinta Basin withi reservoirs in similar lacustrine and related deposits.Bluebell field is the largest oil-producing area in the Uinta basin of northern Utah. The field includes over 300 wells and has produced 137 MMbbl oil and 177 bcf gas from fractured Paleocene-Eocene lacustrine

  6. Spatial and Temporal Characteristics of Historical Oil and Gas Wells in Pennsylvania: Implications for New Shale Gas Resources.

    Science.gov (United States)

    Dilmore, Robert M; Sams, James I; Glosser, Deborah; Carter, Kristin M; Bain, Daniel J

    2015-10-20

    Recent large-scale development of oil and gas from low-permeability unconventional formations (e.g., shales, tight sands, and coal seams) has raised concern about potential environmental impacts. If left improperly sealed, legacy oil and gas wells colocated with that new development represent a potential pathway for unwanted migration of fluids (brine, drilling and stimulation fluids, oil, and gas). Uncertainty in the number, location, and abandonment state of legacy wells hinders environmental assessment of exploration and production activity. The objective of this study is to apply publicly available information on Pennsylvania oil and gas wells to better understand their potential to serve as pathways for unwanted fluid migration. This study presents a synthesis of historical reports and digital well records to provide insights into spatial and temporal trends in oil and gas development. Areas with a higher density of wells abandoned prior to the mid-20th century, when more modern well-sealing requirements took effect in Pennsylvania, and areas where conventional oil and gas production penetrated to or through intervals that may be affected by new Marcellus shale development are identified. This information may help to address questions of environmental risk related to new extraction activities.

  7. Audio-tactile stimulation: A tool to improve health and well-being?

    NARCIS (Netherlands)

    Dijk, E.O.; Nijholt, A.; Erp, J.B.F. van; Wolferen, G. van; Kuyper, E.

    2013-01-01

    Stimulation of the tactile sense or the hearing sense can be used to improve a person's health and well-being. For example, to make someone relax, feel better or sleep better. In this position paper, we present the concept of auditory-tactile stimulation for health and well-being. Through carefully

  8. ENHANCED OIL RECOVERY WITH DOWNHOLE VIBRATION STIMULATION IN OSAGE COUNTY OKLAHOMA

    Energy Technology Data Exchange (ETDEWEB)

    Robert Westermark; J. Ford Brett

    2003-11-01

    This Final Report covers the entire project from July 13, 2000 to June 30, 2003. The report summarizes the details of the work done on the project entitled ''Enhanced Oil Recovery with Downhole Vibration Stimulation in Osage County Oklahoma'' under DOE Contract Number DE-FG26-00BC15191. The project was divided into nine separate tasks. This report is written in an effort to document the lessons learned during the completion of each task. Therefore each task will be discussed as the work evolved for that task throughout the duration of the project. Most of the tasks are being worked on simultaneously, but certain tasks were dependent on earlier tasks being completed. During the three years of project activities, twelve quarterly technical reports were submitted for the project. Many individual topic and task specific reports were included as appendices in the quarterly reports. Ten of these reports have been included as appendices to this final report. Two technical papers, which were written and accepted by the Society of Petroleum Engineers, have also been included as appendices. The three primary goals of the project were to build a downhole vibration tool (DHVT) to be installed in seven inch casing, conduct a field test of vibration stimulation in a mature waterflooded field and evaluate the effects of the vibration on both the produced fluid characteristics and injection well performance. The field test results are as follows: In Phase I of the field test the DHVT performed exceeding well, generating strong clean signals on command and as designed. During this phase Lawrence Berkeley National Laboratory had installed downhole geophones and hydrophones to monitor the signal generated by the downhole vibrator. The signals recorded were strong and clear. Phase II was planned to be ninety-day reservoir stimulation field test. This portion of the field tests was abruptly ended after one week of operations, when the DHVT became stuck in the well

  9. Horizontal oil well applications and oil recovery assessment. Volume 2: Applications overview, Final report

    Energy Technology Data Exchange (ETDEWEB)

    Deskins, W.G.; McDonald, W.J.; Knoll, R.G.; Springer, S.J.

    1995-03-01

    Horizontal technology has been applied in over 110 formations in the USA. Volume 1 of this study addresses the overall success of horizontal technology, especially in less-publicized formations, i.e., other than the Austin Chalk, Bakken, and Niobrara. Operators in the USA and Canada were surveyed on a formation-by-formation basis by means of a questionnaire. Response data were received describing horizontal well projects in 58 formations in the USA and 88 in Canada. Operators` responses were analyzed for trends in technical and economic success based on lithology (clastics and carbonates) and resource type (light oil, heavy oil, and gas). The potential impact of horizontal technology on reserves was also estimated. A forecast of horizontal drilling activity over the next decade was developed.

  10. Regulation for oil wells logging using ionizing radiation sources. A draft

    International Nuclear Information System (INIS)

    Hidrowoh, Jacob

    2000-01-01

    A project to regulate logging activities using ionizing radiation sources in oil wells in Ecuador is proposed. Its development is based on basic concepts of energy, radiation protection and characteristics of oil exploitation in Ecuador

  11. Development of a Non-Intrusive Diagnosis Technique for Gas Lifted Oil Wells

    International Nuclear Information System (INIS)

    Abidi, Tawfik; Guellouz, Mohamed Sadok; Harbaoui, Mohamed; Ellejmi, Mohamed

    2009-01-01

    In the present study a numerical model, representative of a real gas-lifted oil well, is used to perform flow simulations under different states of the oil reservoir. The simulations results helped to establish correlations between the well state and the measurable parameters at the well head. The uniqueness of these correlations, allows the reliable diagnosis of the state of the well by inferring the anomalies affecting it based on easily measurable parameters with no need to stop the oil production

  12. A plugging solution for cementing deep oil and gas wells

    Energy Technology Data Exchange (ETDEWEB)

    Angelopulo, O K; Bakshutov, V S; Bikbau, M Ya; Danyushevskiy, V S; Ilyukhin, V V; Khydyrov, M B; Lobov, L L; Nikolayeva, M K; Nikulin, V Ya; Nudelman, B I

    1983-01-01

    In order to use the solution in a temperature range of -10 to +250 degrees in conditions of salt agression, a plugging solution for cementing deep oil and gas wells, which contains a ground clinker, a mineral additive, a slaking liquid and a modifier additive, is made up in the following manner: ground chlorosilicate clinker is used as the clinker (alynite portland cement) (100 parts); a mixture of gypsum and limestone with peat or cope in a 1 to 3 to 4 to 3 to 8 ratio is used as the mineral additive (5 to 65 parts); the slaking liquid is water of a 1 to 2.5 percent aqueous solution of electrolytes of CaC/sub 12/ or K/sub 2/CO/sub 3/ (42 to 115.5 parts), while the modifier additive is an aqueous solution of liquid glass or polyacrylate (0.05 to 17.55 parts). The solution contains an analyte clinker of the following mineral composition, in parts by weight: Ca/sub 3/Si0/sub 4/C1/sub 2/ (alynite), 100; Ca/sub 2/Si0/sub 3/C1/sub 2/, 2.2 to 33.2; 12CuO with 7A1/sub 2/0/sub 3/, 2.2 to 25.0; CuO with 5A1/sub 2/0/sub 3/, 1.1 to 8.3; CuO with 2A10/sub 2/, 1.1 to 8.3; 4CaO with A1/sub 2/0/sub 3/ with Fe/sub 2/0/sub 3/, 15.6 to 25.0; 2CuO with Fe/sub 2/0/sub 3/, 0.1 to 5.0; a glass phase of 0.3 to 25.0 and free CuO, 0.6 to 2.5; and total MgO, 0.3 to 2.5.

  13. Microbial Dynamics During a Temporal Sequence of Bioreduction Stimulated by Emulsified Vegetable Oil

    Science.gov (United States)

    Schadt, C. W.; Gihring, T. M.; Yang, Z.; Wu, W.; Green, S.; Overholt, W.; Zhang, G.; Brandt, C. C.; Campbell, J. H.; Carroll, S. C.; Criddle, C.; Jardine, P. M.; Lowe, K.; Mehlhorn, T.; Kostka, J. E.; Watson, D. B.; Brooks, S. C.

    2011-12-01

    Amendments of slow-release substrates (e.g. emulsified vegetable oil; EVO) are potentially pragmatic alternatives to short-lived labile substrates for sustained uranium bioimmobilization within groundwater systems. The spatial and temporal dynamics of geochemical and microbial community changes during EVO amendment are likely to differ significantly from populations stimulated by readily utilizable soluble substrates (e.g. ethanol or acetate). We tracked dynamic changes in geochemistry and microbial communities for 270 days following a one-time EVO injection at the Oak Ridge Integrated Field Research Challenge (ORIFRC) site that resulted in decreased groundwater U concentrations for ~4 months. Pyrosequencing and quantitative PCR of 16S rRNA and dissimilatory sulfite reductase (dsrA) genes from monitoring well samples revealed a rapid decline in bacterial community richness and evenness after EVO injection, concurrent with increased 16S rRNA copy levels, indicating the selection of a narrow group consisting of 10-15 dominant OTUs, rather than a broad community stimulation. By association of the known physiology of close relatives identified in the pyrosequencing analysis, it is possible to infer a hypothesized sequence of microbial functions leading the major changes in electron donors and acceptors in the system. Members of the Firmicutes family Veillonellaceae dominated after injection and most likely catalyzed the initial oil decomposition and utilized the glycerol associated with the oils. Sulfate-reducing bacteria from the genus Desulforegula, known for LCFA oxidation to acetate, also dominated shortly after EVO amendment and are thought to catalyze this process. Acetate and H2 production during LCFA degradation appeared to stimulate NO3-, Fe(III), U(VI), and SO42- reduction by members of the Comamonadaceae, Geobacteriaceae, and Desulfobacterales. Methanogenic archaea flourished late in the experiment and in some samples constituted over 25 % of the total

  14. Temperature control of thermal-gas-dynamical installation in cleaning oil-well tubes

    Science.gov (United States)

    Penner, V. A.; Martemyanov, D. B.; Pshenichnikova, V. V.

    2017-08-01

    The article provides the study results of cleaning oil-well tubes, the oil-well tube failure reasons for service by their types have been considered. The chemical method of cleaning oil-well tubes as the least expensive has been reviewed when acid solution moves to the interptube space mixing up with oil and liquidates paraffin and pitches deposits on the internal pipe surface. Except the chemical method of pipes cleaning the mechanical one was considered as well. Also the disadvantages -such as the low productivity of cleaning and design complexity- of this deposits removal method on the internal oil-well tube surface have been considered. An effective method for cleaning oil-well tubing from paraffin and pitches by the thermodynamic plant based on the aircraft engine has been introduced for the first time. The temperature distribution graph in the gas stream at the engine output has been given.

  15. Oil-water flows in wells with powerful fracture reservoirs

    Energy Technology Data Exchange (ETDEWEB)

    Ivanov, N.P.

    1979-01-01

    The character of two phase liquid flows from powerful layer fractures to bottom holes in Starogrodnen and Malgobek-Voznesenskiy fields in the Chechen-Ingush ASSR found in the late stage of operation. The studies were done with the electrothermometer TEG-36, the manometer MGN-2, the remote control thermal flow meter T-4, the remote control moisture meter VBST-1, the density meter GGP-1M, whose accuracy class is 1.0 and whose working limits are: temperature, up to 150/sup 0/C and pressure, up to 1000 kGs/cm/sup 2/. The breakdown of the linear filtration law and the gravitational division of the water-oil mixture phase occurred during fieldwork. The oil and water, etc., flow intervals were defined. The data from the moisture meter and the gamma density meter coincided.

  16. Movement of gasified oil in an infinite stratum drained by a single well

    Energy Technology Data Exchange (ETDEWEB)

    Tomel' gas, V A

    1965-01-01

    This article presents a method of calculating the flow of gas and oil into a well, which drains a reservoir by the solution drive mechanism. The following conditions are assumed: (1) Initially, an infinite homogeneous reservoir is saturated with oil above the bubble point; (2) the well draining the reservoir is operated at constant pressure, below the bubble point; and (3) the reservoir contains 2 zones; the zone fartherest from the well contains only oil at a pressure above the bubble point, while the zone nearest the well contains both oil and gas. The pressure and oil saturation gradients around the well are calculated for a variety of conditions, and the results are shown graphically. As pressure drawdown increases, oil production increases and the gas factor at first decreases and then increases rapidly.

  17. Neutron control of well debit increasing by acoustic influence on oil formation

    International Nuclear Information System (INIS)

    Bogdanovich, B.Yu.; Nesterovich, A.V.; Khasaya, D.R.; Shikanov, A.E.; Shikanov, E.A.; Il'inskiy, A.V.; Mihailov, L.V.; Kolomiets, N.F.

    2012-01-01

    The effectiveness of the A E direction in oil reservoirs can be improved by controlling the parameters of the processes occurring before and after acoustic effect in oil reservoirs, followed by a choice of intervals stimulation of oil. Measurements of changes in these processes in the reservoir are made remotely via a metal pipe casing that requires the use of transparent methods of control. In implementing the method of pulse neutron-neutron logging in the study area provide periodic field impulse of fast neutrons emitted by the accelerating tube, resulting in leakage to its target nuclear reaction T (d, n) 4He

  18. A Simple Physics-Based Model Predicts Oil Production from Thousands of Horizontal Wells in Shales

    KAUST Repository

    Patzek, Tadeusz

    2017-10-18

    Over the last six years, crude oil production from shales and ultra-deep GOM in the United States has accounted for most of the net increase of global oil production. Therefore, it is important to have a good predictive model of oil production and ultimate recovery in shale wells. Here we introduce a simple model of producing oil and solution gas from the horizontal hydrofractured wells. This model is consistent with the basic physics and geometry of the extraction process. We then apply our model thousands of wells in the Eagle Ford shale. Given well geometry, we obtain a one-dimensional nonlinear pressure diffusion equation that governs flow of mostly oil and solution gas. In principle, solutions of this equation depend on many parameters, but in practice and within a given oil shale, all but three can be fixed at typical values, leading to a nonlinear diffusion problem we linearize and solve exactly with a scaling

  19. Evaluation of Oil-Industry Stimulation Practices for Engineered Geothermal Systems

    Energy Technology Data Exchange (ETDEWEB)

    Peter Van Dyke; Leen Weijers; Ann Robertson-Tait; Norm Warpinski; Mike Mayerhofer; Bill Minner; Craig Cipolla

    2007-10-17

    Geothermal energy extraction is typically achieved by use of long open-hole intervals in an attempt to connect the well with the greatest possible rock mass. This presents a problem for the development of Enhanced (Engineered) Geothermal Systems (EGS), owing to the challenge of obtaining uniform stimulation throughout the open-hole interval. Fluids are often injected in only a fraction of that interval, reducing heat transfer efficiency and increasing energy cost. Pinnacle Technologies, Inc. and GeothermEx, Inc. evaluated a variety of techniques and methods that are commonly used for hydraulic fracturing of oil and gas wells to increase and evaluate stimulation effectiveness in EGS wells. Headed by Leen Weijers, formerly Manager of Technical Development at Pinnacle Technologies, Inc., the project ran from August 1, 2004 to July 31, 2006 in two one-year periods to address the following tasks and milestones: 1) Analyze stimulation results from the closest oil-field equivalents for EGS applications in the United States (e.g., the Barnett Shale in North Texas) (section 3 on page 8). Pinnacle Technologies, Inc. has collected fracture growth data from thousands of stimulations (section 3.1 on page 12). This data was further evaluated in the context of: a) Identifying techniques best suited to developing a stimulated EGS fracture network (section 3.2 on page 29), and b) quantifying the growth of the network under various conditions to develop a calibrated model for fracture network growth (section 3.3 on page 30). The developed model can be used to design optimized EGS fracture networks that maximize contact with the heat source and minimize short-circuiting (section 3.4 on page 38). 2) Evaluate methods used in oil field applications to improve fluid diversion and penetration and determine their applicability to EGS (section 4 on page 50). These methods include, but are not limited to: a) Stimulation strategies (propped fracturing versus water fracturing versus injecting

  20. An Innovative Oil Pollution Containment Method for Ship Wrecks Proposed for Offshore Well Blow-outs

    OpenAIRE

    ANDRITSOS Fivos; COJINS Hans

    2011-01-01

    In the aftermath of the PRESTIGE disaster, an innovative system for the prompt intervention on oil pollution sources (primarily ship wrecks) at great depths was conceived at the Joint Research Center of the European Commission. This system, with some re-engineering, could also serve for collecting oil and gas leaking after an offshore well blow-out and could constitute a reference method for prompt intervention on deep water oil pollution sources like ship wrecks and blown-out offshore wells....

  1. Assessment of Uinta Basin Oil and Natural Gas Well Pad Pneumatic Controller Emissions

    Science.gov (United States)

    In the fall of 2016, a field study was conducted in the Uinta Basin Utah to improve information on oil and natural gas well pad pneumatic controllers (PCs) and emission measurement methods. A total of 80 PC systems at five oil sites (supporting six wells) and three gas sites (sup...

  2. Using acoustics to study and stimulate the coalescence of oil drops surrounded by water

    Energy Technology Data Exchange (ETDEWEB)

    Gardner, E.A.; Apfel, R.E. (Yale Univ., New Haven, CT (United States). Dept. of Mechanical Engineering)

    1993-08-01

    The coalescence of oil drops in water is studied using acoustic levitation and stimulated with acoustic cavitation. Unlike most earlier studies, which investigate the coalescence of a single drop with an initially planar interface, the use of acoustic radiation forces allows two drops to be brought into contact and allowed to coalesce. The acoustic technique has the advantage over other drop-drop coalescence systems in that the drops remain in contact until they coalesce without the use of solid supports to control them. Additionally, acoustic cavitation is observed to deposit sufficient energy in the oil-water interface to trigger the coalescence of a pair of 2-mm-diameter drops. This stimulation mechanism could have application to emulsion breaking. Some of the factors that affect spontaneous and stimulated coalescence are investigated.

  3. Records of wells drilled for oil and gas in New Mexico

    Science.gov (United States)

    Dixon, G.H.; Baltz, D.H.; Stipp, T.F.; Bieberman, R.A.

    1954-01-01

    Data concerning nearly 3,000 of the more than 13,000 wells drilled in New Mexico, before September 1, 1953, including unsuccessful wildcat and field extension wells and most of the discovery wells, have been compiled and are published in this circular. Although the search for oil and gas has extended to all parts of the State, most of the wells and all the oil and natural gas fields are located in the northwest and southeast quadrants of the State.

  4. A fast simulation tool for evaluation of novel well stimulation techniques for tight gas reservoirs

    NARCIS (Netherlands)

    Egberts, P.J.P.; Peters, E.

    2015-01-01

    For stimulation of tight fields, alternatives to hydraulic fracturing based on hydraulic jetting are becoming available. With hydraulic jetting many (10 to 20) laterals can be created in a (sub-) vertical well. The laterals are 100 to 200 m long, typically 4 laterals are applied with a small

  5. Understanding gas production mechanism and effectiveness of well stimulation in the Haynesville shale through reservoir simulation

    Energy Technology Data Exchange (ETDEWEB)

    Fan, L.; Thompson, J.W.; Robinson, J.R. [Schlumberger, Houston, TX (United States)

    2010-07-01

    The Haynesville Shale Basin is one of the large and most active shale gas plays in the United States, with 185 horizontal rigs currently in place. The Haynesville Shale is a very tight source rock and resource play. The gas resources are being converted into gas reserves with horizontal wells and hydraulic fracture treatments. A complex fracture network created during well stimulation is the main factor in generating superior early well performance in the area. The key to making better wells in all the gas shale plays is to understand how to create more surface area during hydraulic stimulation jobs and preserve the surface area for as long as possible. This paper presented a unique workflow and methodology that has enabled analysis of production data using reservoir simulation to explain the shale gas production mechanism and the effectiveness of stimulation treatments along laterals. Since 2008, this methodology has been used to analyze production data from more than 30 horizontal wells in the Haynesville Shale. Factors and parameters relating to short and long term well performance were investigated, including pore pressure, rock matrix quality, natural fractures, hydraulic fractures, and complex fracture networks. Operators can use the simulation results to determine where and how to spend resources to produce better wells and to reduce the uncertainties of developing these properties. 19 refs., 1 tab., 17 figs.

  6. Proposal for regulation of logging activities in oil wells using ionizing radiation sources

    International Nuclear Information System (INIS)

    Hidrowoh, Jacob R.

    2000-01-01

    It covers general aspects of nuclear energy and the suitable legal frame for its application related to oil industry. Besides, a regulation proposal to control logging activities in Ecuador using ionizing radiation sources in oil wells. It was prepared taking into account the Ecuadorian Atomic Energy Commission criteria and international regulations

  7. Well and Inflow Performance Relationship for Heavy Oil Reservoir under Heating Treatment

    KAUST Repository

    Hakiki, Farizal

    2017-10-17

    Well and Inflow Performance Relationship, termed TPR and IPR, respectively have been the unfailing methods to predict well performance. It is further to determine the schemes on optimising production. The main intention of the study is to explore TPR and IPR under heating treatment for heavy oil well. Klamono is a mature field which mostly has depleted wells, it produces heavy oil within 18.5 °API (>0.95 g/cc oil density), and therefore, artificial lifting method is necessary. Sucker Road Pump (SRP) and Electrical Submersible Pump (ESP) are the most deployed artificial lifting method in this reservoir. To boost the heavy oil production, the application of Electric Downhole Heater (EDH) in Well KLO-X1 is being studied. Whole Klamono\\'s production is more than 100,000 blpd within 97-99% water cut. By installing EDH, oil viscosity is decreased hence oil mobility ratio will play a role to decrease water cut. EDH is installed together with the tubing joint to simplify its application in the wellbore. The study shows that EDH application can elevate fluid (mixed oil and brine) temperature. Oil viscosity confirms a reduction from 68 to 46 cP. The gross well production is up to 12.2 bopd due optimising its outflow performance and reducing 97.5 to 96.9% water cut. The field data gives an incremental of 4.9 bopd. The computational results only show an attainment of net oil production up to 8.3 bopd (2 bopd incremental). The EDH works to lessen both density and viscosity as we hypothesised for the mechanism of thermally induced oil production improvement. The evaluation study on its economics aspect exhibits good result that is 1.4 USD/bbl additional profit margin according to field data despite the challenging annual rig rent cost. Following the field data, the expected net income through analytical model revealed that this project is financially promising.

  8. Well and Inflow Performance Relationship for Heavy Oil Reservoir under Heating Treatment

    KAUST Repository

    Hakiki, Farizal; Aditya, A.; Ulitha, D. T.; Shidqi, M.; Adi, W. S.; Wibowo, K. H.; Barus, M.

    2017-01-01

    Well and Inflow Performance Relationship, termed TPR and IPR, respectively have been the unfailing methods to predict well performance. It is further to determine the schemes on optimising production. The main intention of the study is to explore TPR and IPR under heating treatment for heavy oil well. Klamono is a mature field which mostly has depleted wells, it produces heavy oil within 18.5 °API (>0.95 g/cc oil density), and therefore, artificial lifting method is necessary. Sucker Road Pump (SRP) and Electrical Submersible Pump (ESP) are the most deployed artificial lifting method in this reservoir. To boost the heavy oil production, the application of Electric Downhole Heater (EDH) in Well KLO-X1 is being studied. Whole Klamono's production is more than 100,000 blpd within 97-99% water cut. By installing EDH, oil viscosity is decreased hence oil mobility ratio will play a role to decrease water cut. EDH is installed together with the tubing joint to simplify its application in the wellbore. The study shows that EDH application can elevate fluid (mixed oil and brine) temperature. Oil viscosity confirms a reduction from 68 to 46 cP. The gross well production is up to 12.2 bopd due optimising its outflow performance and reducing 97.5 to 96.9% water cut. The field data gives an incremental of 4.9 bopd. The computational results only show an attainment of net oil production up to 8.3 bopd (2 bopd incremental). The EDH works to lessen both density and viscosity as we hypothesised for the mechanism of thermally induced oil production improvement. The evaluation study on its economics aspect exhibits good result that is 1.4 USD/bbl additional profit margin according to field data despite the challenging annual rig rent cost. Following the field data, the expected net income through analytical model revealed that this project is financially promising.

  9. Slender wells and new subsea solutions for increased oil recovery

    Energy Technology Data Exchange (ETDEWEB)

    Faanes, Audun; Myhre, Erling; Vinge, Torstein; Stroem, Steinar

    2010-07-01

    Statoil has identified cost effective subsea wells as one of our major challenges. To achieve such solutions it is required to look at all sides of a subsea development. This presentation will cover how a slim wellhead, BOP and riser system will contribute to a less costly subsea development. The focus will be on all aspects of a subsea development. The effect on the drilling rig will be discussed based on the fact that the drilling rig is the major cost driver in subsea well developments. (Author)

  10. Macondo-1 well oil in sediment and tarballs from the northern Gulf of Mexico shoreline

    Science.gov (United States)

    Wong, Florence L.; Rosenbauer, Robert J.; Campbell, Pamela L.; Lam, Angela; Lorenson, T.D.; Hostettler, Frances D.; Thomas, Burt

    2011-01-01

    From April 20 through July 15, 2010, an estimated 4.4 million barrels (1 barrel = 42 gallons [~700,000 cu m]) of crude oil spilled into the northern Gulf of Mexico (nGOM) from the ruptured British Petroleum (BP) Macondo-1 (M-1) well after the explosion of the drilling platform Deepwater Horizon. In addition, ~1.84 million gallons (~7,000 cu m) of hydrocarbon-based Corexit dispersants were applied to the oil both on and below the sea surface (Operational Science Advisory Team, 2010). An estimate of the total extent of the surface oil slick, derived from wind, ocean currents, aerial photography, and satellite imagery, was 68,000 square miles (~180,000 sq km; Amos and Norse, 2010). Spilled oil from this event impacted sensitive habitat along the shores of the nGOM. In response to this environmental catastrophe, the U.S. Geological Survey (USGS) collected coastal sediment and tarball samples along the shores of the nGOM from Texas to Florida before and after oil made landfall. These sites included priority areas of the nGOM at highest risk for oil contamination. These areas included coastal wetlands, shorelines, and barrier islands that could suffer severe environmental damage if a significant amount of oil came ashore. Samples were collected before oil reached land from 69 sites; 49 were revisited to collect samples after oil landfall. This poster focuses on the samples from locations that were sampled on both occasions. The USGS samples and one M-1 well-oil sample provided by BP were analyzed for a suite of diagnostic geochemical biomarkers. Aided by multivariate statistical analysis, the M-1 well oil was not detected in the samples collected before landfall but have been identified in sediment and tarballs collected from Louisiana, Alabama, Mississippi, and Florida after landfall. None of the sediment hydrocarbon extracts from Texas correlated with the M-1 well oil. Oil-impacted sediment is confined to the shoreline adjacent to the cumulative oil slick of the

  11. An additive to well injection water for increasing the oil yield

    Energy Technology Data Exchange (ETDEWEB)

    Absov, M.T.; Abutalybov, M.G.; Aslanov, S.M.; Movruzov, E.N.; Musaev, R.A.; Tairov, N.D.

    1979-03-05

    This invention relates to oil production using flooding. The goal of this invention is to increase the oil yield of a producing formation. This is achieved by using a saponin solution as an additive to the water injected into the formation (with related organic substances which are complex organic nitrogen-free compounds from the glycoside group; these substances yield solution that foam easily with an agitation). The use of saponin facilitates good solubility in fresh, sea and formation (alkaline and hard) waters, as well as the absence of sediment formation during dissolution, low solid adsorption, and a significant decrease in the surface water tension on the oil-water boundary. The aqueous saponin solution makes it possible to decrease the production cost of oil, as well as to decrease the development time of the fields and the volume of water injected into the formation and to significantly increase the oil yield.

  12. Evaluation the complex lithologies in the oil well using spectral density instrument

    International Nuclear Information System (INIS)

    Zivanov, M.; Martinovic, S.; Jakovljevic, B.

    1991-01-01

    Spectral density instrument for logging in the oil wells, beside density, measure photo electrical cross section. The principles of logging are discussed of modern spectral density. Results of logging are used dor determining the complex lithology in the oil well. With this instrument are obtained the more accurate and reliable logging results and better lithology rate and reliable logging results and better lithology determination in the formations. (author)

  13. 80,000 Inactive Oil Wells: A Blessing or a Curse?

    Directory of Open Access Journals (Sweden)

    Lucija Muehlenbachs

    2017-02-01

    Full Text Available For a century, oil and gas wells have been Alberta’s economic pride. That there could be a hidden cost in maintaining these wells past their productive life is difficult to imagine, much less accept. The financial burden of abandoning a well officially is no doubt why Alberta producers delay doing so as long as possible. Turning a blind eye, they routinely keep non-producing wells in a state of “inactive” suspension and refuse to rule out the possibility that someday oil prices or technology, or both, will change significantly enough to make those wells profitable again. In most cases that will never happen, but the province plays along anyway: It enforces no limit on how long a well can be kept inactive before it must be reactivated or abandoned. While a convenience for well owners, there is no benefit to Albertans. They are exposed to the risk of thousands of inactive wells becoming a hazardous threat to public safety. The longer a well is inactive, the higher the likelihood that its owner may no longer be around to arrange and pay for its official abandonment, a process whereby wells are permanently sealed using regulated methods that insure they cause no environmental damage. Oil and gas producers come and go. Periodic price shocks, like the one that recently ravaged the sector, drive companies into insolvency. When the owner of an inactive well is no longer around to pay for its abandonment costs, the well becomes orphaned. Alberta’s permissive policies have led to a situation where there are now more than 80,000 inactive wells in the province. Some have been inactive for decades. If the possibility existed that they could eventually become economical, those wells might be considered a blessing. However, the simulations that model scenarios where prices are substantially higher or where production technology is significantly improved, clearly show that the vast majority of these wells will never be reactivated, no matter how

  14. A history of nuclear well logging in the oil industry

    International Nuclear Information System (INIS)

    Tittle, C.W.

    1989-01-01

    Spurred by an interest in logging through steel casing γ-ray logging began in the late 1930s followed soon by neutron logging for porosity. These were the first two nuclear well logs. Gamma-gamma density logging was developed during the 1950s. Pulsed neutron lifetime logging appeared in the 1960s; the slim tools came in the early 1970s. Developments since then have included dual detector devices of several types which offered improved measurements or interpretation, γ-ray spectrometry logging (natural and neutron-induced) which identifies certain chemical elements, induced radioactivity logging, and the photoelectric absorption log, which, combined with the density log in a single tool, is known as litho-density logging. A combination of several γ-ray spectrometers in one tool, designed to determine 10 formation elements, was recently introduced, and a new neutron porosity tool measuring epithermal neutron die-away time has been developed. Digital transmission of logging data was a step forward in about 1975. Also, log interpretation techniques have greatly expanded since the advent of digital computers, and the microcomputer has had a distinct impact. It is now practical and economical to do iterative analysis on a suite of logs to obtain an optimum overall interpretation. (author)

  15. Reservoir response to thermal and high-pressure well stimulation efforts at Raft River, Idaho

    Energy Technology Data Exchange (ETDEWEB)

    Plummer, Mitchell [Idaho National Lab. (INL), Idaho Falls, ID (United States); Bradford, Jacob [Energy & Geoscience Institute at the Univ. of Utah, Salt Lake City, UT (United States); Moore, Joseph [Energy & Geoscience Institute at the Univ. of Utah, Salt Lake City, UT (United States); Podgorney, Robert [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2016-08-01

    An injection stimulation test begun at the Raft River geothermal reservoir in June, 2013 has produced a wealth of data describing well and reservoir response via high-resolution temperature logging and distributed temperature sensing, seismic monitoring, periodic borehole televiewer logging, periodic stepped flow rate tests and tracer injections before and after stimulation efforts. One of the primary measures of response to the stimulation is the relationship between fluid pressure and flow rate, short-term during forced flow rate changes and the long-term change in injectivity. In this paper we examine that hydraulic response using standard pumping test analysis methods, largely because pressure response to the stimulation was not detected, or measurable, in other wells. Analysis of stepped rate flow tests supports the inference from other data that a large fracture, with a radial extent of one to several meters, intersects the well in the target reservoir, suggests that the flow regime is radial to a distance of only several meters and demonstrates that the pressure build-up cone reaches an effective constant head at that distance. The well’s longer term hydraulic response demonstrated continually increasing injectivity but at a dramatically faster rate later from ~2 years out and continuing to the present. The net change in injectivity is significantly greater than observed in other longterm injectivity monitoring studies, with an approximately 150–fold increase occurring over ~2.5 years. While gradually increasing injectivity is a likely consequence of slow migration of a cooling front, and consequent dilation of fractures, the steady, ongoing, rate of increase is contrary to what would be expected in a radial or linear flow regime, where the cooling front would slow with time. As a result, occasional step-like changes in injectivity, immediately following high-flow rate tests suggest that hydro shearing during high-pressure testing altered the near-well

  16. Inelastic neutron scattering reactions in fluid saturated rock as exploited in oil well logging

    International Nuclear Information System (INIS)

    Underwood, M.C.; Dyos, C.J.

    1986-01-01

    Oil saturated sandstone and limestone targets have been irradiated with 14 MeV neutrons. Gamma-ray spectra were accumulated and the γ-ray intensities arising from inelastic neutron scattering reactions upon carbon and oxygen measured. The results are compared with the predictions of a simple model. They enable some features of the response of (n,γ) tools used in oil well logging to be established and current uncertainties in understanding to be highlighted. (author)

  17. Oil Well Blowout 3D computational modeling: review of methodology and environmental requirements

    OpenAIRE

    Pedro Mello Paiva; Alexandre Nunes Barreto; Jader Lugon Junior; Leticia Ferraço de Campos

    2016-01-01

    This literature review aims to present the different methodologies used in the three-dimensional modeling of the hydrocarbons dispersion originated from an oil well blowout. It presents the concepts of coastal environmental sensitivity and vulnerability, their importance for prioritizing the most vulnerable areas in case of contingency, and the relevant legislation. We also discuss some limitations about the methodology currently used in environmental studies of oil drift, which considers sim...

  18. Unconventional Oil Reserves Development in the Viking Play (Western Canada Using Horizontal Wells and Hydraulic Fracturing

    Directory of Open Access Journals (Sweden)

    T.B. Baishev

    2017-09-01

    Full Text Available Oil production from the Viking play in Saskatchewan province started in the 1950s and continues since that time. Horizontal drilling and multistage fracturing have caused resurgence in development of this play. Based on the production data from several fields, the comparative results of the Viking play development using vertical and horizontal wells are presented. Horizontal wells drilling made it possible to increase oil production in those formation zones that were previously considered predominantly gas-saturated, as well as in the zones affected by water injection using vertical wells in order to maintain reservoir pressure. Infill drilling combined with longer lateral completion length also positively affected the development of oil reserves from the Viking play.

  19. Reconnaissance of Macondo-1 well oil in sediment and tarballs from the northern Gulf of Mexico shoreline, Texas to Florida

    Science.gov (United States)

    Rosenbauer, Robert J.; Campbell, Pamela L.; Lam, Angela; Lorenson, T.D.; Hostettler, Frances D.; Thomas, Burt; Wong, Florence L.

    2010-01-01

    Hydrocarbons were extracted and analyzed from sediment and tarballs collected from the northern Gulf of Mexico (nGOM) coast that is potentially impacted by Macondo-1 (M-1) well oil. The samples were analyzed for a suite of diagnostic geochemical biomarkers. Aided by multivariate statistical analysis, the M-1 well oil has been identified in sediment and tarballs collected from Louisiana, Alabama, Mississippi, and Florida. None of the sediment hydrocarbon extracts from Texas correlated with the M-1 well oil. Oil-impacted sediments are confined to the shoreline adjacent to the cumulative oil slick of the Deepwater Horizon oil spill, and no impact was observed outside of this area.

  20. Stimulation of deep gas wells using HCl/formic acid system : lab studies and field application

    Energy Technology Data Exchange (ETDEWEB)

    Nasr-El-Din, H.A.; Al-Mutairi, S.; Al-Malki, B. [Saudi Aramco (Saudi Arabia); Metcalf, S.; Walters, W. [BJ Services Co USA, Houston, TX (United States)

    2002-06-01

    Well stimulation in the deep carbonate Khuff reservoirs in eastern Saudi Arabia is needed to remove drilling mud filter cakes and to enhance reservoir permeability. A non associated gas is being produced from the reservoirs. This gas is associated with the hydrogen sulfide content that varies from 0 to 10-mol per cent. The average reservoir temperature is 275 degrees F and initial reservoir pressure is 7,000 psi. A special system is needed to stimulate the carbonate reservoir because of this high bottomhole temperature and the corrosive nature of hydrochloric acid (HCl) at high temperature. A rotating disk method was used to determine the reaction rate of an HCl/formic acid system with reservoir rocks. Results from coreflood tests showed that the acid system creates deep wormholes in tight reservoir cores. Corrosion tests showed that the well tubulars could tolerate the acid system. A gelled 15-wt per cent HCl/9-wt per cent formic acid system successfully fractured 3 vertical wells in deep sour gas reservoirs without any operational problems. The treatment resulted in significant increases in gas production and flowing wellhead pressures. In addition, overflush of the treatment successfully eliminated the return of live acid after the treatment. 37 refs., 10 tabs., 17 figs.

  1. A Simple Physics-Based Model Predicts Oil Production from Thousands of Horizontal Wells in Shales

    KAUST Repository

    Patzek, Tadeusz; Saputra, Wardana; Kirati, Wissem

    2017-01-01

    and ultimate recovery in shale wells. Here we introduce a simple model of producing oil and solution gas from the horizontal hydrofractured wells. This model is consistent with the basic physics and geometry of the extraction process. We then apply our model

  2. The Role of Well Control Training in Developing Safe Onshore and Offshore Oil Drilling Operations

    Science.gov (United States)

    Abulhassn, Aber

    2016-01-01

    This research investigates the role of the International Well Control Forum (IWCF) Rotary Drilling Well Control Training Program in developing safe oil drilling operations from the perspective of onshore and offshore drilling crews. The research methodology is a qualitative case study. A total of 40 IWCF candidates were interviewed, with 10 from…

  3. An Investigation on Gas Lift Performance Curve in an Oil-Producing Well

    Directory of Open Access Journals (Sweden)

    Deni Saepudin

    2007-01-01

    Full Text Available The main objective in oil production system using gas lift technique is to obtain the optimum gas injection rate which yields the maximum oil production rate. Relationship between gas injection rate and oil production rate is described by a continuous gas lift performance curve (GLPC. Obtaining the optimum gas injection rate is important because excessive gas injection will reduce production rate, and also increase the operation cost. In this paper, we discuss a mathematical model for gas lift technique and the characteristics of the GLPC for a production well, for which one phase (liquid is flowing in the reservoir, and two phases (liquid and gas in the tubing. It is shown that in certain physical condition the GLPC exists and is unique. Numerical computations indicate unimodal properties of the GLPC. It is also constructed here a numerical scheme based on genetic algorithm to compute the optimum oil production.

  4. Enhancing heavy oil recovery using foam injection in applications to cyclic steam stimulation

    Energy Technology Data Exchange (ETDEWEB)

    Isaacs, E. [Alberta Energy Research Inst., Edmonton, AB (Canada); Yuan, J.Y. [Canadian Natural Resources Ltd., Calgary, AB (Canada)

    2008-07-01

    Cyclic steam stimulation (CSS) is a widely used heavy oil production technology. However, steam-based processes that are not stabilized can develop conformance as the steam can over-ride and channel past oil-bearing zones. This presentation discussed a refined CSS steam foaming process designed to improve recovery in marginal cycles. Laboratory studies were initially conducted to examine surfactant properties and flow behaviour in porous media. The results of numerical simulations were then applied to the steam-foaming portion of the CSS process. Results of the study showed that during the foam co-injection with steam stage, the steam injection rate did not alter. Improvement to the CSS process varied, indicating that earlier foam forming surfactant co-injection was preferable when steam-foam performance was constant in all cycles. It was concluded that the steam foaming process may improve bitumen production without requiring additional steam. 13 refs., 5 figs.

  5. An improved method for predicting brittleness of rocks via well logs in tight oil reservoirs

    Science.gov (United States)

    Wang, Zhenlin; Sun, Ting; Feng, Cheng; Wang, Wei; Han, Chuang

    2018-06-01

    There can be no industrial oil production in tight oil reservoirs until fracturing is undertaken. Under such conditions, the brittleness of the rocks is a very important factor. However, it has so far been difficult to predict. In this paper, the selected study area is the tight oil reservoirs in Lucaogou formation, Permian, Jimusaer sag, Junggar basin. According to the transformation of dynamic and static rock mechanics parameters and the correction of confining pressure, an improved method is proposed for quantitatively predicting the brittleness of rocks via well logs in tight oil reservoirs. First, 19 typical tight oil core samples are selected in the study area. Their static Young’s modulus, static Poisson’s ratio and petrophysical parameters are measured. In addition, the static brittleness indices of four other tight oil cores are measured under different confining pressure conditions. Second, the dynamic Young’s modulus, Poisson’s ratio and brittleness index are calculated using the compressional and shear wave velocity. With combination of the measured and calculated results, the transformation model of dynamic and static brittleness index is built based on the influence of porosity and clay content. The comparison of the predicted brittleness indices and measured results shows that the model has high accuracy. Third, on the basis of the experimental data under different confining pressure conditions, the amplifying factor of brittleness index is proposed to correct for the influence of confining pressure on the brittleness index. Finally, the above improved models are applied to formation evaluation via well logs. Compared with the results before correction, the results of the improved models agree better with the experimental data, which indicates that the improved models have better application effects. The brittleness index prediction method of tight oil reservoirs is improved in this research. It is of great importance in the optimization of

  6. Improving reservoir history matching of EM heated heavy oil reservoirs via cross-well seismic tomography

    KAUST Repository

    Katterbauer, Klemens

    2014-01-01

    Enhanced recovery methods have become significant in the industry\\'s drive to increase recovery rates from oil and gas reservoirs. For heavy oil reservoirs, the immobility of the oil at reservoir temperatures, caused by its high viscosity, limits the recovery rates and strains the economic viability of these fields. While thermal recovery methods, such as steam injection or THAI, have extensively been applied in the field, their success has so far been limited due to prohibitive heat losses and the difficulty in controlling the combustion process. Electromagnetic (EM) heating via high-frequency EM radiation has attracted attention due to its wide applicability in different environments, its efficiency, and the improved controllability of the heating process. While becoming a promising technology for heavy oil recovery, its effect on overall reservoir production and fluid displacements are poorly understood. Reservoir history matching has become a vital tool for the oil & gas industry to increase recovery rates. Limited research has been undertaken so far to capture the nonlinear reservoir dynamics and significantly varying flow rates for thermally heated heavy oil reservoir that may notably change production rates and render conventional history matching frameworks more challenging. We present a new history matching framework for EM heated heavy oil reservoirs incorporating cross-well seismic imaging. Interfacing an EM heating solver to a reservoir simulator via Andrade’s equation, we couple the system to an ensemble Kalman filter based history matching framework incorporating a cross-well seismic survey module. With increasing power levels and heating applied to the heavy oil reservoirs, reservoir dynamics change considerably and may lead to widely differing production forecasts and increased uncertainty. We have shown that the incorporation of seismic observations into the EnKF framework can significantly enhance reservoir simulations, decrease forecasting

  7. Process for recovering oil from oil-bearing layers traversed by a well

    Energy Technology Data Exchange (ETDEWEB)

    Brandon, C W

    1967-09-11

    In this process, pressure is applied to the surface of the strata exposed in the well. The applied pressure is varied between values above and below the pressure of the formation adjacent to the well bore, thus causing fracturing and breaking of the formation under the influence of the internal pressure of the layer.

  8. The Synthesis of 58co-Naphthenate Complex Compound for Evaluation of Oil well Production Capacity

    International Nuclear Information System (INIS)

    Duyeh Setiawan; Marlina

    2009-01-01

    The nuclear technique using radioisotope as a tracer in oil industry has assisted to solve the degradation of oil production. Usually, the degradation of oil production in well caused by the formation changing of hydrostatic pressure of the oil layer in the well. This problem could be evaluated by injection of water to oil well, for recovering this hydrostatic pressure. The watcher of the water injection success is done by the way of nuclear technique radioactive tracer systems, applied radioisotope having short half life and low gamma radiation energy. Radioisotope cobalt-58 in the complex form with naphthenate ( 58 Co-naphthenate ) often used as the tracer in the water injection technique. The tracer 58 Co-naphthenate relatively easy to synthesis and radioisotope 58 Co has half life 70.86 days and gamma energy was 0.811 Me v. The synthesis method of 58 Co-naphthenate route has been carried out by mixing of 58 CoCl 2 radioisotope solution with sodium naphthenate (C 5 H 9 CH 2 COONa) in the optimum condition. The results shows that the optimal mole ratio of cobalt-58 and naphthenate was 1:6 which produced 87,38 % of ren dement and 82,5 % of efficiency labelling. This synthesis technique was made permanent procedure for making of 58 Co-naphthenate complex as radioactive tracer in service of radioisotope production especially industrial area. (author)

  9. Creating potentiometric surfaces from combined water well and oil well data in the midcontinent of the United States

    Science.gov (United States)

    Gianoutsos, Nicholas J.; Nelson, Philip H.

    2013-01-01

    For years, hydrologists have defined potentiometric surfaces using measured hydraulic-head values in water wells from aquifers. Down-dip, the oil and gas industry is also interested in the formation pressures of many of the same geologic formations for the purpose of hydrocarbon recovery. In oil and gas exploration, drillstem tests (DSTs) provide the formation pressure for a given depth interval in a well. These DST measurements can be used to calculate hydraulic-head values in deep hydrocarbon-bearing formations in areas where water wells do not exist. Unlike hydraulic-head measurements in water wells, which have a low number of problematic data points (outliers), only a small subset of the DST data measure true formation pressures. Using 3D imaging capabilities to view and clean the data, we have developed a process to estimate potentiometric surfaces from erratic DST data sets of hydrocarbon-bearing formations in the midcontinent of the U.S. The analysis indicates that the potentiometric surface is more readily defined through human interpretation of the chaotic DST data sets rather than through the application of filtering and geostatistical analysis. The data are viewed as a series of narrow, 400-mile-long swaths and a 2D viewer is used to select a subset of hydraulic-head values that represent the potentiometric surface. The user-selected subsets for each swath are then combined into one data set for each formation. These data are then joined with the hydraulic-head values from water wells to define the 3D potentiometric surfaces. The final product is an interactive, 3D digital display containing: (1) the subsurface structure of the formation, (2) the cluster of DST-derived hydraulic head values, (3) the user-selected subset of hydraulic-head values that define the potentiometric surface, (4) the hydraulic-head measurements from the corresponding shallow aquifer, (5) the resulting potentiometric surface encompassing both oil and gas and water wells, and (6

  10. Initiating events of accidents in the practice of oil well logging in Cuba

    International Nuclear Information System (INIS)

    Alles Leal, A.; Perez Reyes, Y.; Dumenigo Gonzalez, C.

    2013-01-01

    The oil well logging is an extremely important activity within the oil industry, but in turn, brings risks that occasionally result in damage to health, the environment and economic losses. In this context, risk analysis has become an important tool to control them through their prediction and the study of the factors that determine them, enabling substantiated decisions to, first, foresee accidents and, secondly, to minimize their consequences. This paper proposes the elaboration of a list of initiating events of accidents in the practice of oil well logging which is one of the most important aspects for further evaluation of radiation safety of this practice. For its determination the technique employed to identify risks was 'Failure Modes and Effects Analysis (FMEA)' by applying it to the different stages and processes of practice. (Author)

  11. Application of accelerator sources for pulsed neutron logging of oil and gas wells

    International Nuclear Information System (INIS)

    Randall, R.R.

    1985-01-01

    Dresser Atlas introduced the first commercial pulsed neutron oil well log in the early 1960s. This log had the capability of differentiating oil from salt water in a completed well. In the late 1970s the first continuous carbon/oxygen (C/O) log capable of differentiating oil from fresh water was introduced. The sources used in these commercial logs are radial geometry deuterium-tritium reaction devices with Cockcroft-Walton voltage multipliers providing the accelerator voltage. The commercial logging tools using these accelerators are comprised of scintillators detectors, power supplies, line drivers and receivers, and various timing and communication electronics. They are used to measure either the time decay or energy spectra of neutron-induced gamma events. The time decay information is useful in determining the neutron capture cross section, and the energy spectra is used to characterize inelastic neutron events. (orig.)

  12. Application of accelerator sources for pulsed neutron logging of oil and gas wells

    Science.gov (United States)

    Randall, R. R.

    1985-05-01

    Dresser Atlas introduced the first commercial pulsed neutron oil well log in the early 1960s. This log had the capability of differentiating oil from salt water in a completed well. In the late 1970s the first continuous carbon/oxygen (C/O) log capable of differentiating oil from fresh water was introduced. The sources used in these commercial logs are radial geometry deuterium-tritium reaction devices with Cockcroft-Walton voltage multipliers providing the accelerator voltage. The commercial logging tools using these accelerators are comprised of scintillators detectors, power supplies, line drivers and receivers, and various timing and communications electronics. They are used to measure either the time decay or energy spectra of neutron-induced gamma events. The time decay information is useful in determining the neutron capture cross section, and the energy spectra is used to characterize inelastic neutron events.

  13. Correlation of the Canol Formation source rock with oil from Norman Wells

    Energy Technology Data Exchange (ETDEWEB)

    Snowdon, L.R.; Brooks, P.W.; Williams, G.K.; Goodarzi, F.

    1987-01-01

    The source of the oil at Norman Wells has long been assumed to have been the Canol Formation and/or the Bluefish Member of the Hare Indian Formation. These two units are stratigraphically above and below the Kee Scarp Formation reservoir unit respectively, and are both bituminous shales. A wide range of analytical techniques including Rock-Eval pyrolysis, solvent extraction and fractionation, capillary gas chromatography, gas chromatography-mass spectrometry, and white light and fluorescence microscopy has been used to characterize core samples of these two units and two samples of crude oil from the Norman Wells field. Most of the analytical techniques were insufficiently refined to either differentiate the extracts from each other or to make a definitive oil/source rock correlation. Collision activated decomposition coupled with multiple ion detection mass spectrometry (GC-MS-MS) did provide sufficient chemical compositional detail of the oils and the two potential sources to demonstrate that the Canol Formation has been the effective source of the Normal Wells oil whereas the Bluefish Member has not. The level of thermal maturity of the core samples ranges from immature to moderately mature in the vicinity of the Norman Wells field to overmature for the samples obtained to the west and north of the field. The level of thermal maturity of the oil was observed to be somewhat higher than that of the samples of the source formation directly above the field. It was thus inferred that some lateral migration from more mature areas has occurred but the extent of this migration was not necessarily more than a few to tens of kilometers.

  14. Measurement of polynuclear aromatic hydrocarbon concentrations in the plume of Kuwait oil well fires

    International Nuclear Information System (INIS)

    Olsen, K.B.; Wright, C.W.; Veverka, C.; Ball, J.C.; Stevens, R.

    1995-03-01

    Following their retreat from Kuwait during February and March of 1991, the Iraqi Army set fire to over 500 oil wells dispersed throughout the Kuwait oil fields. During the period of sampling from July to August 1991, it was estimated that between 3.29 x 10 6 barrels per day of crude oil were combusted. The resulting fires produced several plumes of black and white smoke that coalesced to form a composite ''super'' plume. Because these fires were uncontrolled, significant quantities of organic materials were dispersed into the atmosphere and drifted throughout the Middle East. The organic particulants associated with the plume of the oil well fires had a potential to be rich in polynuclear aromatic hydrocarbon (PAH) compounds. Based on the extreme mutagenic and carcinogenic activities of PAHs found in laboratory testing, a serious health threat to the population of that region potentially existed. Furthermore, the Kuwait oil fire plumes represented a unique opportunity to study the atmospheric chemistry associated with PAHs in the plume. If samples were collected near the plume source and from the plume many kilometers downwind from the source, comparisons could be made to better understand atmospheric reactions associated with particle-bound and gas-phase PAHs. To help answer health-related concerns and to better understand the fate and transport of PAHs in an atmospheric environment, a sampling and analysis program was developed

  15. Oil well fires of Operation Desert Storm--defining troop exposures and determining health risks.

    Science.gov (United States)

    Heller, Jack M

    2011-07-01

    During Operation Desert Storm, in February 1991, Iraqi troops began burning Kuwaiti oil wells. Almost immediately there was concern about possible adverse health effects in U.S. personnel exposed to crude oil combustion products. Combustions products were predicted from the known composition of Kuwaiti crude oil. Monitoring sites were established in Saudi Arabia and Kuwait; about 5,000 environmental samples were studied. Data collected were used to develop health risk assessments for the geographic areas sampled. This initial approach to assessing risk had to be greatly expanded when Congress passed Public Law 102-190, requiring development of means to calculate environmental exposures for individual U.S. service members. To estimate daily exposure levels for the entire area over 10 months for all U.S. troops, air dispersion modeling was used in conjunction with satellite imagery and geographic information system technology. This methodology made it possible to separate the risk caused by oil fire smoke from the total risk from all sources for each service member. The U.S. military responses to health concerns related to the oil well fires and to Public Law 102-190 were reviewed. Consideration was given to changes in technology, practices, and policies over the last two decades that might impact a similar contemporary response.

  16. Oil Well Blowout 3D computational modeling: review of methodology and environmental requirements

    Directory of Open Access Journals (Sweden)

    Pedro Mello Paiva

    2016-12-01

    Full Text Available This literature review aims to present the different methodologies used in the three-dimensional modeling of the hydrocarbons dispersion originated from an oil well blowout. It presents the concepts of coastal environmental sensitivity and vulnerability, their importance for prioritizing the most vulnerable areas in case of contingency, and the relevant legislation. We also discuss some limitations about the methodology currently used in environmental studies of oil drift, which considers simplification of the spill on the surface, even in the well blowout scenario. Efforts to better understand the oil and gas behavior in the water column and three-dimensional modeling of the trajectory gained strength after the Deepwater Horizon spill in 2010 in the Gulf of Mexico. The data collected and the observations made during the accident were widely used for adjustment of the models, incorporating various factors related to hydrodynamic forcing and weathering processes to which the hydrocarbons are subjected during subsurface leaks. The difficulties show to be even more challenging in the case of blowouts in deep waters, where the uncertainties are still larger. The studies addressed different variables to make adjustments of oil and gas dispersion models along the upward trajectory. Factors that exert strong influences include: speed of the subsurface currents;  gas separation from the main plume; hydrate formation, dissolution of oil and gas droplets; variations in droplet diameter; intrusion of the droplets at intermediate depths; biodegradation; and appropriate parametrization of the density, salinity and temperature profiles of water through the column.

  17. chemical as well as biological properties of the oil of Alpinia galanga

    African Journals Online (AJOL)

    bt

    2016-11-30

    Nov 30, 2016 ... Physico-chemical properties, antioxidant activities as well as antimicrobial activities of the oils were .... ones (like aldehydes: 7.29%, alcohols: 32.43%, ketones: ... capable of being dissolved in both polar organic and nonpolar ...

  18. High Sensitivity Gravity Measurements in the Adverse Environment of Oil Wells

    Science.gov (United States)

    Pfutzner, Harold

    2014-03-01

    Bulk density is a primary measurement within oil and gas reservoirs and is the basis of most reserves calculations by oil companies. The measurement is performed with a gamma-ray source and two scintillation gamma-ray detectors from within newly drilled exploration and production wells. This nuclear density measurement, while very precise is also very shallow and is therefore susceptible to errors due to any alteration of the formation and fluids in the vicinity of the borehole caused by the drilling process. Measuring acceleration due to gravity along a well provides a direct measure of bulk density with a very large depth of investigation that makes it practically immune to errors from near-borehole effects. Advances in gravity sensors and associated mechanics and electronics provide an opportunity for routine borehole gravity measurements with comparable density precision to the nuclear density measurement and with sufficient ruggedness to survive the rough handling and high temperatures experienced in oil well logging. We will describe a borehole gravity meter and its use under very realistic conditions in an oil well in Saudi Arabia. The density measurements will be presented. Alberto Marsala (2), Paul Wanjau (1), Olivier Moyal (1), and Justin Mlcak (1); (1) Schlumberger, (2) Saudi Aramco.

  19. Phenolic Compounds in Extra Virgin Olive Oil Stimulate Human Osteoblastic Cell Proliferation

    Science.gov (United States)

    García-Martínez, Olga; De Luna-Bertos, Elvira; Ramos-Torrecillas, Javier; Ruiz, Concepción; Milia, Egle; Lorenzo, María Luisa; Jimenez, Brigida; Sánchez-Ortiz, Araceli; Rivas, Ana

    2016-01-01

    In this study, we aimed to clarify the effects of phenolic compounds and extracts from different extra virgin olive oil (EVOO) varieties obtained from fruits of different ripening stages on osteoblast cells (MG-63) proliferation. Cell proliferation was increased by hydroxytyrosol, luteolin, apigenin, p-coumaric, caffeic, and ferulic acids by approximately 11–16%, as compared with controls that were treated with one vehicle alone, while (+)-pinoresinol, oleuropein, sinapic, vanillic acid and derivative (vanillin) did not affect cell proliferation. All phenolic extracts stimulated MG-63 cell growth, and they induced higher cell proliferation rates than individual compounds. The most effective EVOO phenolic extracts were those obtained from the Picual variety, as they significantly increased cell proliferation by 18–22%. Conversely, Arbequina phenolic extracts increased cell proliferation by 9–13%. A decline in osteoblast proliferation was observed in oils obtained from olive fruits collected at the end of the harvest period, as their total phenolic content decreases at this late stage. Further research on the signaling pathways of olive oil phenolic compounds involved in the processes and their metabolism should be carried out to develop new interventions and adjuvant therapies using EVOO for bone health (i.e.osteoporosis) in adulthood and the elderly. PMID:26930190

  20. Phenolic Compounds in Extra Virgin Olive Oil Stimulate Human Osteoblastic Cell Proliferation.

    Science.gov (United States)

    García-Martínez, Olga; De Luna-Bertos, Elvira; Ramos-Torrecillas, Javier; Ruiz, Concepción; Milia, Egle; Lorenzo, María Luisa; Jimenez, Brigida; Sánchez-Ortiz, Araceli; Rivas, Ana

    2016-01-01

    In this study, we aimed to clarify the effects of phenolic compounds and extracts from different extra virgin olive oil (EVOO) varieties obtained from fruits of different ripening stages on osteoblast cells (MG-63) proliferation. Cell proliferation was increased by hydroxytyrosol, luteolin, apigenin, p-coumaric, caffeic, and ferulic acids by approximately 11-16%, as compared with controls that were treated with one vehicle alone, while (+)-pinoresinol, oleuropein, sinapic, vanillic acid and derivative (vanillin) did not affect cell proliferation. All phenolic extracts stimulated MG-63 cell growth, and they induced higher cell proliferation rates than individual compounds. The most effective EVOO phenolic extracts were those obtained from the Picual variety, as they significantly increased cell proliferation by 18-22%. Conversely, Arbequina phenolic extracts increased cell proliferation by 9-13%. A decline in osteoblast proliferation was observed in oils obtained from olive fruits collected at the end of the harvest period, as their total phenolic content decreases at this late stage. Further research on the signaling pathways of olive oil phenolic compounds involved in the processes and their metabolism should be carried out to develop new interventions and adjuvant therapies using EVOO for bone health (i.e.osteoporosis) in adulthood and the elderly.

  1. Calculational techniques for estimating population doses from radioactivity in natural gas from nuclearly stimulated wells

    International Nuclear Information System (INIS)

    Barton, C.J.; Moore, R.E.; Rohwer, P.S.; Kaye, S.V.

    1975-01-01

    Techniques for estimating radiation doses from exposure to combustion products of natural gas obtained from wells created by use of nuclear explosives were first developed in the Gasbuggy Project. These techniques were refined and extended by development of a number of computer codes in studies related to the Rulison Project, the second in the series of joint government-industry efforts to demonstrate the feasibility of increasing natural gas production from low-permeability rock formations by use of nuclear explosives. These techniques are described and dose estimates that illustrate their use are given. These dose estimation studies have been primarily theoretical, but we have tried to make our hypothetical exposure conditions correspond as closely as possible with conditions that could exist if nuclearly stimulated natural gas is used commercially. (author)

  2. Computer-Based Monitoring and Remote Controlling for Oil Well Pumps Using Scada

    Directory of Open Access Journals (Sweden)

    Rudi Tjiptadi

    2011-12-01

    Full Text Available The research aims to change manually the monitoring and controlling of oil well pumps into a computer-based system using SCADA (Supervisory and Data Acquisition system. To design the protection system which consists of controller unit and display system, RTU (Remote Terminal Unit and MTU (Master Terminal Unit are used. The research results in a controller unit which is able to communicate to personal computer using RS-232 C and an alarm system to protect oil pump motors by detecting sensors installed at the pumps. 

  3. Study on thermal history and oil-generated environment from well CC1

    International Nuclear Information System (INIS)

    Xia Yuliang; Zhu Jiechen; Zheng Maogong

    1997-01-01

    U-Pb isotope geochronological study of core samples implies that the sedimentary strata are derived from North-China ancient land and the age of the hidden granite derived from the remelted Archean rocks with lower crust signature is 99 Ma. Fluid inclusion investigation indicates that the Ordovician carbonate rocks are rich in organic matters and should be a better set of oil-generated rocks and reservoir. Based on fission track analysis of apatites from different depths and the paleo-geothermal variation, the authors suggest that there be at least three oil-generated stages. The range of annealing belt of apatite tracks and the paleo-geothermal gradient in this well are 1700-3900 m (roughly corresponding to oil-generated belt) and 3.1 degree C/100 m respectively after Tertiary sedimentation

  4. Well-to-refinery emissions and net-energy analysis of China's crude-oil supply

    Science.gov (United States)

    Masnadi, Mohammad S.; El-Houjeiri, Hassan M.; Schunack, Dominik; Li, Yunpo; Roberts, Samori O.; Przesmitzki, Steven; Brandt, Adam R.; Wang, Michael

    2018-03-01

    Oil is China's second-largest energy source, so it is essential to understand the country's greenhouse gas emissions from crude-oil production. Chinese crude supply is sourced from numerous major global petroleum producers. Here, we use a per-barrel well-to-refinery life-cycle analysis model with data derived from hundreds of public and commercial sources to model the Chinese crude mix and the upstream carbon intensities and energetic productivity of China's crude supply. We generate a carbon-denominated supply curve representing Chinese crude-oil supply from 146 oilfields in 20 countries. The selected fields are estimated to emit between 1.5 and 46.9 g CO2eq MJ-1 of oil, with volume-weighted average emissions of 8.4 g CO2eq MJ-1. These estimates are higher than some existing databases, illustrating the importance of bottom-up models to support life-cycle analysis databases. This study provides quantitative insight into China's energy policy and the economic and environmental implications of China's oil consumption.

  5. The wells of the Lipinki oil field in the aspect of borehole heat exchangers retrained

    Directory of Open Access Journals (Sweden)

    Andrzej Gonet

    2006-10-01

    Full Text Available Geological conditions of the Gorlice-Lipinki structure are presented in the paper. The construction of a well in the Lipinki oil field was characterized on this basis. The authors analysed an adaptability of the wells intothe borehole heat exchangers (BHE with its potential heating power estimation on the basis of an example. In the article, a discussion of the heat consumer choose, which can be buildings by a local communite utilization.

  6. Produced Water Treatment Using Geothermal Energy from Oil and Gas Wells: An Appropriateness of Decommissioned Wells Index (ADWI) Approach

    Science.gov (United States)

    Kiaghadi, A.; Rifai, H. S.

    2016-12-01

    This study investigated the feasibility of harnessing geothermal energy from retrofitted oil and gas decommissioned wells to power desalination units and overcome the produced water treatment energy barrier. Previous studies using heat transfer models have indicated that well depth, geothermal gradient, formation heat conductivity, and produced water salt levels were the most important constraints that affect the achievable volume of treated water. Thus, the challenge of identifying which wells would be best suited for retrofit as geothermal wells was addressed by defining an Appropriateness of Decommissioned Wells Index (ADWI) using a 25 km x 25 km grid over Texas. Heat transfer modeling combined with fuzzy logic methodology were used to estimate the ADWI at each grid cell using the scale of Very Poor, Poor, Average, Good and Excellent. Values for each of the four constraints were extracted from existing databases and were used to select 20 representative values that covered the full range of the data. A heat transfer model was run for all the 160,000 possible combination scenarios and the results were regressed to estimate weighting coefficients that indicate the relative effect of well depth, geothermal gradient, heat conductivity, and produced water salt levels on the volume of treated water in Texas. The results indicated that wells located in cells with ADWI of "Average", "Good" or "Excellent" can potentially deliver 35,000, 106,000, or 240,000 L/day of treated water, respectively. Almost 98% of the cells in the Granite Wash, 97% in Eagle Ford Shale, 90% in Haynesville Shale, 79% in Permian Basin, and 78% in Barnett Shale were identified as better than "Average" locations; whereas, south of the Eagle Ford, southwestern Permian Basin, and the center of Granite Wash were "Excellent". Importantly, most of the locations with better than "Average" ADWI are within drought prone agricultural regions that would benefit from this resilient source of clean water.

  7. Effect of well network density on economic effectiveness of exploiting oil and gas fields

    Energy Technology Data Exchange (ETDEWEB)

    Kortunov, I V; Kats, A Ya

    1965-04-01

    A detailed discussion is presented of procedures and reasoning used by Soviet economists to determine the cost of producing a ton of oil. According to some authors the cost of production is at a minimum if less than 1% of the reserve is produced per year. This approach assumes a very large well spacing and that the wells flow. Other authors show that the cost of production does not continuously decrease as well spacing is increased. Data to support each argument are presented. No agreement is reached as to the best method of determining the most economic well spacing.

  8. Direct measurements of methane emissions from abandoned oil and gas wells in Pennsylvania.

    Science.gov (United States)

    Kang, Mary; Kanno, Cynthia M; Reid, Matthew C; Zhang, Xin; Mauzerall, Denise L; Celia, Michael A; Chen, Yuheng; Onstott, Tullis C

    2014-12-23

    Abandoned oil and gas wells provide a potential pathway for subsurface migration and emissions of methane and other fluids to the atmosphere. Little is known about methane fluxes from the millions of abandoned wells that exist in the United States. Here, we report direct measurements of methane fluxes from abandoned oil and gas wells in Pennsylvania, using static flux chambers. A total of 42 and 52 direct measurements were made at wells and at locations near the wells ("controls") in forested, wetland, grassland, and river areas in July, August, October 2013 and January 2014, respectively. The mean methane flow rates at these well locations were 0.27 kg/d/well, and the mean methane flow rate at the control locations was 4.5 × 10(-6) kg/d/location. Three out of the 19 measured wells were high emitters that had methane flow rates that were three orders of magnitude larger than the median flow rate of 1.3 × 10(-3) kg/d/well. Assuming the mean flow rate found here is representative of all abandoned wells in Pennsylvania, we scaled the methane emissions to be 4-7% of estimated total anthropogenic methane emissions in Pennsylvania. The presence of ethane, propane, and n-butane, along with the methane isotopic composition, indicate that the emitted methane is predominantly of thermogenic origin. These measurements show that methane emissions from abandoned oil and gas wells can be significant. The research required to quantify these emissions nationally should be undertaken so they can be accurately described and included in greenhouse gas emissions inventories.

  9. Evolution of Hydrocarbon-Degrading Microbial Communities in the Aftermath of the Deepwater Horizon Oil Well Blowout in the Gulf of Mexico

    Science.gov (United States)

    Andersen, G.; Dubinsky, E. A.; Chakraborty, R.; Hollibaugh, J. T.; Hazen, T. C.

    2012-12-01

    The Deepwater Horizon oil spill created large plumes of dispersed oil and gas that remained deep in the water column and stimulated growth of several deep-sea bacteria that can degrade hydrocarbons at cold temperatures. We tracked microbial community composition before, during and after the 83-day spill to determine relationships between microbial dynamics, and hydrocarbon and dissolved-oxygen concentrations. Dominant bacteria in plumes shifted drastically over time and were dependent on the concentration of hydrocarbons, and the relative quantities of insoluble and soluble oil fractions. Unmitigated flow from the wellhead early in the spill resulted in the highest concentrations of oil and relatively more n-alkanes suspended in the plume as small oil droplets. These conditions resulted in near complete dominance by alkane-degrading Oceanospirillales, Pseudomonas and Shewanella. Six-weeks into the spill overall hydrocarbon concentrations in the plume decreased and were almost entirely composed of BTEX after management actions reduced emissions into the water column. These conditions corresponded with the emergence of Colwellia, Pseudoalteromonas, Cycloclasticus and Halomonas that are capable of degrading aromatic compounds. After the well was contained dominant plume bacteria disappeared within two weeks after the spill and transitioned to an entirely different set of bacteria dominated by Flavobacteria, Methylophaga, Alteromonas and Rhodobacteraceae that were found in anomalous oxygen depressions throughout August and are prominent degraders of both high molecular weight organic matter as well as hydrocarbons. Bio-Sep beads amended with volatile hydrocarbons from MC-252 oil were used from August through September to create hydrocarbon-amended traps for attracting oil-degrading microbes in situ. Traps were placed at multiple depths on a drilling rig about 600-m from the original MC-252 oil spill site. Microbes were isolated on media using MC-252 oil as the sole

  10. Exocrine pancreatic secretion is stimulated in piglets fed Fish oil compared with those fed Coconut Oil or Lard

    DEFF Research Database (Denmark)

    Hedemann, Mette Skou; Pedersen, Asger Roer; Engberg, Ricarda M.

    2001-01-01

    An experiment was conducted to study the effect of feeding diets containing fat sources with different fatty acid composition (fish oil, coconut oil or lard, 10 g/100 g diet) on exocrine pancreatic secretion in piglets after weaning. A total of 16 barrows were weaned at 4 wk of age; 3 d later...... the coconut oil or lard diets. The output [U/(h. kg(0.75))] of lipase was higher in piglets fed fish oil than in piglets fed lard or coconut oil. The output of colipase was greater in piglets fed fish oil and coconut oil than in those fed lard. The dietary treatments did not affect the output of carboxylester...... hydrolase. The output of trypsin was significantly lower in piglets fed lard than in piglets fed fish oil or coconut oil diets and the output of carboxypeptidase B was greater in those fed the fish oil diet. Protein, chymotrypsin, carboxypeptidase A, elastase and amylase outputs did not differ among...

  11. Behavior and dynamics of bubble breakup in gas pipeline leaks and accidental subsea oil well blowouts.

    Science.gov (United States)

    Wang, Binbin; Socolofsky, Scott A; Lai, Chris C K; Adams, E Eric; Boufadel, Michel C

    2018-06-01

    Subsea oil well blowouts and pipeline leaks release oil and gas to the environment through vigorous jets. Predicting the breakup of the released fluids in oil droplets and gas bubbles is critical to predict the fate of petroleum compounds in the marine water column. To predict the gas bubble size in oil well blowouts and pipeline leaks, we observed and quantified the flow behavior and breakup process of gas for a wide range of orifice diameters and flow rates. Flow behavior at the orifice transitions from pulsing flow to continuous discharge as the jet crosses the sonic point. Breakup dynamics transition from laminar to turbulent at a critical value of the Weber number. Very strong pure gas jets and most gas/liquid co-flowing jets exhibit atomization breakup. Bubble sizes in the atomization regime scale with the jet-to-plume transition length scale and follow -3/5 power-law scaling for a mixture Weber number. Copyright © 2018 Elsevier Ltd. All rights reserved.

  12. Possible techniques for decontamination of natural gas from gas wells stimulated by a nuclear explosion

    Energy Technology Data Exchange (ETDEWEB)

    Wethington, Jr, John A [Lawrence Radiation Laboratory, University of California, Livermore, CA (United States)

    1970-05-15

    Decontamination of the products from gas wells stimulated by nuclear explosions requires the removal of T, present as HT, CH{sub 3}T, C{sub 2}H{sub 5}T, etc., and {sup 85}Kr from the production stream. Flaring of large volumes of gas from the Gasbuggy well led to the replacement of radioactive cavity gas with inactive formation gas, but this would not be a satisfactory production procedure because it releases T and {sup 85}Kr into the atmosphere and wastes large amounts of product gas. Exchange reactions appear to offer promise for removing the tritium. For example, water or steam flowing countercurrent to tritiated gas in the presence of a suitable catalyst can participate in the exchange reactions CH{sub 3}T + H{sub 2}O {r_reversible} CH{sub 4} + HTO, HT + H{sub 2}O {r_reversible} H{sub 2} + HTO, resulting in the transfer of T from gas into water. Other possibilities for utilizing exchange reactions include exchange of the gas with ethylene glycol used in the gas dryer, with silicate rocks introduced into the gas stream, or with a countercurrent stream of NH{sub 3} or H{sub 2}S. As another approach, use of the contaminated gas for the manufacture of ammonia synthesis gas has potential for removal of both T and {sup 85}Kr. (author)

  13. Variability of oil and gas well productivities for continuous (unconventional) petroleum accumulations

    Science.gov (United States)

    Charpentier, Ronald R.; Cook, Troy A.

    2013-01-01

    Over the last decade, oil and gas well productivities were estimated using decline-curve analysis for thousands of wells as part of U.S. Geological Survey (USGS) studies of continuous (unconventional) oil and gas resources in the United States. The estimated ultimate recoveries (EURs) of these wells show great variability that was analyzed at three scales: within an assessment unit (AU), among AUs of similar reservoir type, and among groups of AUs with different reservoir types. Within a particular oil or gas AU (such as the Barnett Shale), EURs vary by about two orders of magnitude between the most productive wells and the least productive ones (excluding those that are dry and abandoned). The distributions of EURs are highly skewed, with most of the wells in the lower part of the range. Continuous AUs were divided into four categories based on reservoir type and major commodity (oil or gas): coalbed gas, shale gas, other low-permeability gas AUs (such as tight sands), and low-permeability oil AUs. Within each of these categories, there is great variability from AU to AU, as shown by plots of multiple EUR distributions. Comparing the means of each distribution within a category shows that the means themselves have a skewed distribution, with a range of approximately one to two orders of magnitude. A comparison of the three gas categories (coalbed gas, shale gas, and other low-permeability gas AUs) shows large overlap in the ranges of EUR distributions. Generally, coalbed gas AUs have lower EUR distributions, shale gas AUs have intermediate sizes, and the other low-permeability gas AUs have higher EUR distributions. The plot of EUR distributions for each category shows the range of variation among developed AUs in an appropriate context for viewing the historical development within a particular AU. The Barnett Shale is used as an example to demonstrate that dividing wells into groups by time allows one to see the changes in EUR distribution. Subdivision into groups

  14. 75 FR 75995 - Request for Comments on Helium-3 Use in the Oil and Natural Gas Well Logging Industry

    Science.gov (United States)

    2010-12-07

    ... manufacture neutron detectors used by the well logging industry or wireline or Logging-While-Drilling tools... DEPARTMENT OF ENERGY Request for Comments on Helium-3 Use in the Oil and Natural Gas Well Logging... of Helium-3 by the oil and gas well logging industry. DATES: Written comments and information are...

  15. Development of ultra-lightweight slurries with high compressive strength for use in oil wells

    Energy Technology Data Exchange (ETDEWEB)

    Suzart, J. Walter P. [Halliburton Company, Houston, TX (United States); Farias, A.C. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil); Ribeiro, Danilo; Fernandes, Thiago; Santos, Reened [Halliburton Energy Services Aberdeen, Scotland (United Kingdom)

    2008-07-01

    Formations with low fracture gradients or depleted reservoirs often lead to difficult oil well cementing operations. Commonly employed cement slurries (14.0 to 15.8 lb/gal), generate an equivalent circulating density (ECD) higher than the fracture gradient and ultimately lead to formation damage, lost circulation and a decreased top of cement. Given the high price of oil, companies are investing in those and other wells that are difficult to explore. Naturally, lightweight cement slurries are used to reduce the ECD (10.0 to 14.0 lb/gal), using additives to trap water and stabilize the slurry. However, when the density reaches 11.0 lb/gal, the increase in water content may cause a change in characteristics. The focus of this study is extreme cases where it is necessary to employ ultra-lightweight cement slurries (5.5 to 10.0 lb/gal). Foamed slurries have been widely used, and the objective is to set an alternative by developing cement slurries containing uncompressible microspheres, aiming for a density of 7.5 lb/gal as well as high compressive strength. Another benefit in contrast to preparing foamed cement slurries is that there is no requirement for special equipment in the field. Routine laboratory tests such as fluid-loss control, sedimentation, thickening time, free water, compressive strength, and rheology (at room and high temperatures) were performed. Thus, it was concluded that the proposed cement slurries can be used in oil wells. (author)

  16. Digital representation of oil and natural gas well pad scars in southwest Wyoming: 2012 update

    Science.gov (United States)

    Garman, Steven L.; McBeth, Jamie L.

    2015-01-01

    The recent proliferation of oil and natural gas energy development in the Greater Green River Basin of southwest Wyoming has accentuated the need to understand wildlife responses to this development. The location and extent of surface disturbance that is created by oil and natural gas well pad scars are key pieces of information used to assess the effects of energy infrastructure on wildlife populations and habitat. A digital database of oil and natural gas pad scars had previously been generated from 1-meter (m) National Agriculture Imagery Program imagery (NAIP) acquired in 2009 for a 7.7-million hectare (ha) (19,026,700 acres) region of southwest Wyoming. Scars included the pad area where wellheads, pumps, and storage facilities reside and the surrounding area that was scraped and denuded of vegetation during the establishment of the pad. Scars containing tanks, compressors, the storage of oil and gas related equipment, and produced-water ponds were also collected on occasion. This report updates the digital database for the five counties of southwest Wyoming (Carbon, Lincoln, Sublette, Sweetwater, Uinta) within the Wyoming Landscape Conservation Initiative (WLCI) study area and for a limited portion of Fremont, Natrona, and Albany Counties using 2012 1-m NAIP imagery and 2012 oil and natural gas well permit information. This report adds pad scars created since 2009, and updates attributes of all pad scars using the 2012 well permit information. These attributes include the origination year of the pad scar, the number of active and inactive wells on or near each pad scar in 2012, and the overall status of the pad scar (active or inactive). The new 2012 database contains 17,404 pad scars of which 15,532 are attributed as oil and natural gas well pads. Digital data are stored as shapefiles projected to the Universal Transverse Mercator (zones 12 and 13) coordinate system. These data are available from the U.S. Geological Survey (USGS) at http://dx.doi.org/10

  17. New technological developments in oil well fire fighting equipment and methods

    Energy Technology Data Exchange (ETDEWEB)

    Matthews, B.; Matthews, R.T.

    1995-12-31

    Since Drake`s first oil well in 1859, well fires have been frequent and disastrous. Hardly a year has passed in over a century without a well fire somewhere in the world. In the 1920`s the classic method of fire fighting using explosives to starve the fire of oxygen was developed and it has been used extensively ever since. While explosives are still one of the most frequently used methods today, several other methods are used to supplement it where special conditions exist. Tunneling at an angle from a safe distance is used in some cases, especially where the fire is too hot for a close approach on the ground surface. Pumping drilling muds into a well to plug it is another method that has been used successfully for some time. Diverter wells are occasionally used, and sometimes simply pumping enough water on a well fire is sufficient to extinguish it. Of course, prevention is always the best solution. Many advances in blow-out prevention devices have been developed in the last 50 years and the number of fires has been substantially reduced compared to the number of wells drilled. However, very little in new technology has been applied to oil well fire fighting in the 1960s, 1970s, or 1980s. Overall technological progress has accelerated tremendously in this period, of course, but new materials and equipment were not applied to this field for some reason. Saddam Hussein`s environmental holocaust in Kuwait changed that by causing many people throughout the world to focus their creative energy on more efficient oil well fire fighting methods.

  18. Some problems in exploitation of deep-pumping wells in Tatarian oil fields

    Energy Technology Data Exchange (ETDEWEB)

    Ishemguzhin, S B

    1970-01-01

    Difficulty has been experienced in pumping paraffinic oil with rod pumps. The rods have scrapers to remove paraffin from tubing walls, however this method does not work well. In an effort to improve pumping efficiency, gas anchors of various types were tried. Best results were obtained when the pumps, equipped with gas anchors, were placed about 300 m under the dynamic liquid level, and separated gas was steadily removed through the annulus. With this arrangement, more complete filling of the pump was achieved. Experience has shown that with separate production of gas from wells, the useful stroke of the pump plunger is increased as well as productivity of deep-pumping equipment.

  19. Application of a non-equilibrium reaction model for describing horizontal well performance in foamy oil

    Energy Technology Data Exchange (ETDEWEB)

    Luigi, A.; Saputelli, B.; Carlas, M.; Canache, P.; Lopez, E. [DPVS Exploracion y Produccion (Venezuela)

    1998-12-31

    This study was designed to determine the activation energy ranges and frequency factor ranges in chemical reactions in heavy oils of the Orinoco Belt in Venezuela, in order to account for the kinetics of physical changes that occur in the morphology of gas-oil dispersion. A non-equilibrium reaction model was used to model foamy oil behaviour observed at SDZ-182 horizontal well in the Zuata field. Results showed that activation energy for the first reaction ranged from 0 to 0.01 BTU/lb-mol and frequency factor from 0.001 to 1000 l/day. For the second reaction the activation energy was 50x10{sub 3} BTU/lb-mol and the frequency factor 2.75x10{sub 1}2 l/day. The second reaction was highly sensitive to the modifications in activation energy and frequency factor. However, both the activation energy and frequency factor were independent of variations for the first reaction. In the case of the activation energy, the results showed that the high sensitivity of this parameter reflected the impact that temperature has on the representation of foamy oil behaviour. 8 refs., 2 tabs., 6 figs.

  20. Asphalts tests using onshore drilling oil wells residues; Ensaios asfalticos utilizando residuos de perfuracao onshore

    Energy Technology Data Exchange (ETDEWEB)

    Lucena, Adriano Elisio de F.L.; Rodrigues, John Kennedy G.; Ferreira, Heber Carlos; Lucena, Leda Christiane de F.L. [Universidade Federal de Campina Grande (UFCG), PB (Brazil); Lucena, Luciana de F.L. [Faculdade de Ciencias Sociais Aplicada (FACISA), Campina Grande, PB (Brazil)

    2008-07-01

    The drilling cuttings are one of the residues produced by the oils industries in large amounts during the drilling of oil wells. An alternative of final disposal of the drilling cutting residue is its utilization in asphalt mixtures. Based on this alternative, it was realized chemical and granulometric analysis and tests (Marshall and indirect tensile strength), on the asphaltic mixture using the residue from the oil drilling wells (well: 1-POTI-4-RN, located at Governador DIX-Sept Rosado - RN - Brazil). The achieved results to Marshall test indicated that for the analyzed mixture, the ideal content of residue that can be incorporated to the asphaltic composition and attend at the DNIT-ES 31 (2006) is 5%. To the indirect tensile strength test, the results showed a strength value higher than the minimum limit requested by the DNIT (0,65 MPa). The achieved results indicated the possibility of the utilization of the drilling cuttings in asphaltic pavements as fine aggregate, obeying the percentage limits, as an alternative to the final disposal. (author)

  1. A new flooding scheme by horizontal well in thin heavy oil reservoirs

    Energy Technology Data Exchange (ETDEWEB)

    Liu, H.; Zhang, H.; Wang, M. [China Univ. of Petroleum, Beijing (China). MOE Key Laboratory of Petroleum Engineering ; Wang, Z. [Shengli Oil Field Co. (China). Dept. of Science and Technology]|[SINOPEC, Shengli (China)

    2008-10-15

    This paper presented a new flooding scheme for single horizontal wells that could improve recovery from thin marginal heavy oil reservoirs or from offshore reservoirs. The scheme involved the use of a multiple tubing string completion in a single wellbore. Special packers were installed within the long completion horizontal interval to establish an injection zone and a production zone. The new flooding scheme also involved simultaneous injection and production. Numerical simulation of the reservoir was used to determine the thickness of the formation and the lower limitation for different viscosities and the optimum time to start steam flooding after steam soaking by economic oil/steam ratio. The peak recovery efficiency of steam flooding was shown to occur when the length of separation section ratio is 0.15 to 0.2. It was concluded that high thermal efficiency in horizontal wells with long completion intervals can be maintained by alternating between steam soaking and steam flooding. Suitable alternation time to steam flooding is a seventh cycle for horizontal wells. Water cut and pressure difference will increase the steam injection rate, and thereby improve the oil production rate. The suitable injection rate for steam flooding is 2.4 t/d.ha.h because of its slow pressure change. 11 refs., 7 figs.

  2. A Novel Terpolymer as Fluid Loss Additive for Oil Well Cement

    Directory of Open Access Journals (Sweden)

    Ming Li

    2017-01-01

    Full Text Available A terpolymer comprised of sodium styrene sulfonate (SSS, fumaric acid (FA, and acrylamide (AM was synthesized by aqueous free radical copolymerization and evaluated as fluid loss additive for oil well cement. The chemical structure and performance of the terpolymer were characterized by Fourier transform infrared (FTIR spectroscopy and thermal gravimetric analysis (TGA; the molecular weight and its distribution were determined by gel permeation chromatography (GPC. The optimum reaction conditions of polymerization were obtained: a reaction temperature of 50°C, a mass ratio of SSS/FA/AM 4 : 2 : 14, initiator 0.1%, and reaction time of 4 h; characterization indicated that the SSS/FA/AM had a certain molecular weight and excellent temperature-resistant and salt-resistant properties. The results show that SSS/FA/AM has a good fluid loss performance, in which the API fluid loss of the oil cement slurry could be controlled within 100 mL at 160°C. In addition, it had little effect on the cement compressive strength. The results of scanning electron microscopy (SEM of the filter cake showed that SSS/FA/AM could be adsorbed on the surface of the cement particles and produce a hydrated layer to prevent fluid loss from the oil well cement.

  3. Well test mathematical model for fractures network in tight oil reservoirs

    Science.gov (United States)

    Diwu, Pengxiang; Liu, Tongjing; Jiang, Baoyi; Wang, Rui; Yang, Peidie; Yang, Jiping; Wang, Zhaoming

    2018-02-01

    Well test, especially build-up test, has been applied widely in the development of tight oil reservoirs, since it is the only available low cost way to directly quantify flow ability and formation heterogeneity parameters. However, because of the fractures network near wellbore, generated from artificial fracturing linking up natural factures, traditional infinite and finite conductivity fracture models usually result in significantly deviation in field application. In this work, considering the random distribution of natural fractures, physical model of fractures network is proposed, and it shows a composite model feature in the large scale. Consequently, a nonhomogeneous composite mathematical model is established with threshold pressure gradient. To solve this model semi-analytically, we proposed a solution approach including Laplace transform and virtual argument Bessel function, and this method is verified by comparing with existing analytical solution. The matching data of typical type curves generated from semi-analytical solution indicates that the proposed physical and mathematical model can describe the type curves characteristic in typical tight oil reservoirs, which have up warping in late-term rather than parallel lines with slope 1/2 or 1/4. It means the composite model could be used into pressure interpretation of artificial fracturing wells in tight oil reservoir.

  4. Real time, real fast : drilling horizontal wells in a heavy oil environment

    Energy Technology Data Exchange (ETDEWEB)

    Balke, S.C.; Rosauer, M.S. [Petrolera Ameriven/Phillips Petroleum, Caracas, (Venezuela)

    2002-07-01

    Eastern Venezuela's Orinoco Tar Belt or the Faja Petrolifera del Orinoco is one of the largest heavy oil fields in the world, containing more than 1.2 trillion barrels of heavy and extra heavy oil with API gravity of 10 to 6. The field is 320 miles long by 40 miles wide and is divided into the Machete, Zuata, Hamaca and Cerro Negro. It has been under production since the 1970s by Venezuela's national oil company, Petroleos de Venezuela SA. The region is only marginally cost effective because of the high costs associated with development. It is expected that the Hamaca Project, which is centrally located in the Orinoco Tar Belt can be effectively and economically developed by applying the latest technology and innovative techniques. Petrolera Ameriven has committed to develop the 250 square mile Hamaca area. The objective is to produce 165,000 acres at rate of 190,000 BOPD for the life of the project. The challenge is that when the oil is cooled and degasified it looks more like a tar or asphalt for paving roads. In addition, the major reservoirs within the field were deposited in low stand and transgressive system tracks consisting of meandering fluvial to fluvial-tidal deltaic deposits. Methods such as logging while drilling (LWD), satellite links and continuous updating and real-time visualization were applied to assess and mitigate risks. These methods made it possible to accurately place the shoe of the build sections for control of well directions. The methods also made it possible to identify sand/shale interfaces, determine the redirection of the drill bit, locate non-pay zones and help plan well paths to optimize production. The technologies developed were also effective in minimizing development costs, thereby improving the financial viability of the project. 1 ref., 16 figs.

  5. Occurrence, sources and health risk of polycyclic aromatic hydrocarbons in soils around oil wells in the border regions between oil fields and suburbs.

    Science.gov (United States)

    Fu, Xiao-Wen; Li, Tian-Yuan; Ji, Lei; Wang, Lei-Lei; Zheng, Li-Wen; Wang, Jia-Ning; Zhang, Qiang

    2018-08-15

    The Yellow River Delta (YRD) is a typical region where oil fields generally overlap cities and towns, leading to complex soil contamination from both the oil fields and human activities. To clarify the distribution, speciation, potential sources and health risk of polycyclic aromatic hydrocarbons (PAHs) in soils of border regions between oil fields and suburbs of the YRD, 138 soil samples (0-20 cm) were collected among 12 sampling sites located around oil wells with different extraction histories. The 16 priority control PAHs (16PAHs), as selected by the United States Environmental Protection Agency (USEPA), were extracted via an accelerated solvent extraction and detected by GC-MS. The results showed that soils of the study area were generally polluted by the 16PAHs. Among these pollutions, chrysene and phenanthrene were the dominant components, and 4-ring PAHs were the most abundant. A typical temporal distribution pattern of the 16PAHs was revealed in soils from different sampling sites around oil wells with different exploitation histories. The concentrations of total 16PAHs and high-ring PAHs (HPAHs) both increased with the extraction time of the nearby oil wells. Individual PAH ratios and PCA method revealed that the 16PAHs in soil with newly developed oil wells were mainly from petroleum pollutants, whereas PAHs in soils around oil wells with a long exploitation history were probably from petroleum contamination; combustion of petroleum, fuel, and biomass; and degradation and migration of PAHs from petroleum. Monte Carlo simulation was used to evaluate the health risks of the 7 carcinogenic PAHs and 9 non-carcinogenic PAHs in the study area. The results indicated that ingestion and dermal contact were the predominant pathways of exposure to PAH residues in soils. Both the carcinogenic and non-carcinogenic burden of the 16PAHs in soils of the oil field increased significantly with exploitation time of nearby oil wells. Copyright © 2018 Elsevier Inc. All

  6. Machine Learning for Mapping Groundwater Salinity with Oil Well Log Data

    Science.gov (United States)

    Chang, W. H.; Shimabukuro, D.; Gillespie, J. M.; Stephens, M.

    2016-12-01

    An oil field may have thousands of wells with detailed petrophysical logs, and far fewer direct measurements of groundwater salinity. Can the former be used to extrapolate the latter into a detailed map of groundwater salinity? California Senate Bill 4, with its requirement to identify Underground Sources of Drinking Water, makes this a question worth answering. A well-known obstacle is that the basic petrophysical equations describe ideal scenarios ("clean wet sand") and even these equations contain many parameters that may vary with location and depth. Accounting for other common scenarios such as high-conductivity shaly sands or low-permeability diatomite (both characteristic of California's Central Valley) causes parameters to proliferate to the point where the model is underdetermined by the data. When parameters outnumber data points, however, is when machine learning methods are most advantageous. We present a method for modeling a generic oil field, where groundwater salinity and lithology are depth series parameters, and the constants in petrophysical equations are scalar parameters. The data are well log measurements (resistivity, porosity, spontaneous potential, and gamma ray) and a small number of direct groundwater salinity measurements. Embedded in the model are petrophysical equations that account for shaly sand and diatomite formations. As a proof of concept, we feed in well logs and salinity measurements from the Lost Hills Oil Field in Kern County, California, and show that with proper regularization and validation the model makes reasonable predictions of groundwater salinity despite the large number of parameters. The model is implemented using Tensorflow, which is an open-source software released by Google in November, 2015 that has been rapidly and widely adopted by machine learning researchers. The code will be made available on Github, and we encourage scrutiny and modification by machine learning researchers and hydrogeologists alike.

  7. Control of waste well casing vent gas from a thermal enhanced oil recovery operation

    International Nuclear Information System (INIS)

    Peavy, M.A.; Braun, J.E.

    1991-01-01

    This paper presents an overview of a waste gas treatment system designed to control emissions from thermally enhanced oil recovery wells. This case study discusses the need, design, installation and operations of the system. Oryx Energy Company (Oryx) operates approximately 940 wells in the Midway-Sunset (MWSS) field under casing vapor recovery systems. The emissions collected from well casing vent gas cotaining hydrocarbons and hydrogen sulfide that are collected and processed through casing vapor recovery skids. These skids are composed of condensers, compressors, and pumps that separate fluids from the waste gas stream. The non-condensible gas is then disposed of in incinerators that reduce the hydrocarbon and sulfur emissions into the atmosphere. Approximately 91,000 lbs/day of hydrocarbon and 10,116 lbs/day of sulfur dioxide are removed from the atmosphere from wells contained within these systems operated by Oryx. These hydrocarbons yield approximately 550 barrels of oil per day (BOPD). The system helps manage the pressure differential from the reservoir into each wellbore and contributes to improved ambient air quality in Kern County, California

  8. Influence of the mineral composition of clay rocks on the stability of oil wells

    International Nuclear Information System (INIS)

    Amorocho, P. R; Badillo, Juan

    2012-01-01

    In the oil companies, the operation of drilling well bore could be more expensive if the composition of the rocks is clay, the cost could increase between 10 and 15% from the starting budget. In order to decrease this problem, the oil industry has spent too much money for developing mechanisms that can provide better control and stability in clay formations during the drilling. The Society Petroleum Engineers (SPE) in some researches have published that the main chemical effects that are involved in the interaction of perforation fluids and the clay formation are: 1) chemical osmosis; and 2) hydration stresses, although, there are others like: Capillary effects, dehydration, differences in pressure and cationic exchange. These factors are not present generally in independent form. At Piedemonte Llanero the problem of the well bore stability represents a high spending of money for oil companies, caused in this region by chemical factors between fluid/rock and mechanical factors as resulted of the stresses in the area. Metil Blue Testing (MBT) and X-ray Diffraction (DR-X) were made in samples of clay; these were taken from cuts extracted of boreholes drilled in some places of the Colombian Llanos. It was found that these samples had a moderate content of reactive and low content of swell minerals.The samples main component was kaolinite, this mineral does not let the rock get swell, but it produces caving in the hole. However, it is necessary to do other tests to quantify the damages and evaluate the influence of there gime of the stress during the perforation of well bore.

  9. Factors affecting bond cement across casing leak zones in oil and gas wells

    Energy Technology Data Exchange (ETDEWEB)

    Nasr, Mohamed; Edbeib, Said [Al-Fateh University, Tripoli (Libyan Arab Jamahiriya). Dept. of Petroleum Engineering

    2004-07-01

    Casing leaks have been a major concern to the oil industry because of their effect on lowering the production rate in many oil and gas wells. The leaks are the result of deterioration of the casing in the well, which is caused by severe corrosion due to the contact of the casing with high salinity foreign fluid. The objective of this study is to determine the factors influencing the mechanical properties of the hardened cement opposite the casing leak zones. This study is conducted by laboratory measurements of the compressive strength of the hardened cement when the cement slurry was mixed with different percentages of formation water and different concentrations of different cement additives. The results of this study indicate that the compressive strength readings obtained from the cement bond log and the cement evaluation tool against the casing leak zones are lower than those readings recorded in adjacent formations. The low cement compressive strength values observed across casing leak zones are due to the contamination of the cement with saline water present in these formations which, in turn, effects the hardening properties of the cement. The experimental results indicated that the salinity of the formation water when mixed with the cement slurry in the presence of cement additives, decreased the compressive strength of the bond cement and also decreased the thickening time of the cement slurry. It is concluded that casing leaks found in many wells observed in oil fields in Libya were due to the mixing of the cement with high salinity formation water present in the lost circulation zones. The high water salinity in these zones effects the setting time of the cement slurry which, therefore, decreased the hardening properties of the bond cement and caused cracks and channels in the hardened cement across lost circulation zones. (author)

  10. Single-layer skull approximations perform well in transcranial direct current stimulation modeling

    NARCIS (Netherlands)

    Rampersad, S.M.; Stegeman, D.F.; Oostendorp, T.F.

    2013-01-01

    In modeling the effect of transcranial direct current stimulation, the representation of the skull is an important factor. In a spherical model, we compared a realistic skull modeling approach, in which the skull consisted of three isotropic layers, to anisotropic and isotropic single-layer

  11. Procedure for recovering embanked bases of oil wells in Carmopolis - state of Sergipe - Brazil

    International Nuclear Information System (INIS)

    Alves, Mara R.F.V.

    2000-01-01

    This present work objective was to elaborate a procedure to deal with degraded areas due to petroleum mining, seeking the recovery of embanked bases of razed oil wells, in Carmopolis/SE. This procedure was a result from studies upon soil recovery and several works performed by Mining Companies, adapted to local conditions. Once defined the objectives and the future soil use, this procedure will take place in four phases: landscape re composition; soil preparation for revegetation; revegetation and management of the area. The suggested procedure application can prove its effectiveness on recovering previous soil uses (farming or local Atlantic Rain Forest). (author)

  12. Determining optimal preventive maintenance interval for component of Well Barrier Element in an Oil & Gas Company

    Science.gov (United States)

    Siswanto, A.; Kurniati, N.

    2018-04-01

    An oil and gas company has 2,268 oil and gas wells. Well Barrier Element (WBE) is installed in a well to protect human, prevent asset damage and minimize harm to the environment. The primary WBE component is Surface Controlled Subsurface Safety Valve (SCSSV). The secondary WBE component is Christmas Tree Valves that consist of four valves i.e. Lower Master Valve (LMV), Upper Master Valve (UMV), Swab Valve (SV) and Wing Valve (WV). Current practice on WBE Preventive Maintenance (PM) program is conducted by considering the suggested schedule as stated on manual. Corrective Maintenance (CM) program is conducted when the component fails unexpectedly. Both PM and CM need cost and may cause production loss. This paper attempts to analyze the failure data and reliability based on historical data. Optimal PM interval is determined in order to minimize the total cost of maintenance per unit time. The optimal PM interval for SCSSV is 730 days, LMV is 985 days, UMV is 910 days, SV is 900 days and WV is 780 days. In average of all components, the cost reduction by implementing the suggested interval is 52%, while the reliability is improved by 4% and the availability is increased by 5%.

  13. Experience in North America Tight Oil Reserves Development. Horizontal Wells and Multistage Hydraulic Fracturing

    Directory of Open Access Journals (Sweden)

    R.R. Ibatullin

    2017-09-01

    Full Text Available The accelerated development of horizontal drilling technology in combination with the multistage hydraulic fracturing of the reservoir has expanded the geological conditions for commercial oil production from tight reservoirs in North America. Geological and physical characteristics of tight reservoirs in North America are presented, as well as a comparison of the geological and physical properties of the reservoirs of the Western Canadian Sedimentary Basin and the Volga-Ural oil and gas province, in particular, in the territory of Tatarstan. The similarity of these basins is shown in terms of formation and deposition. New drilling technologies for horizontal wells (HW and multistage hydraulic fracturing are considered. The drilling in tight reservoirs is carried out exclusively on hydrocarbon-based muds The multi-stage fracturing technology with the use of sliding sleeves, and also slick water – a low-viscous carrier for proppant is the most effective solution for conditions similar to tight reservoirs in the Devonian formation of Tatarstan. Tax incentives which are actively used for the development of HW and multistage fracturing technologies in Canada are described. wells, multistage fracturing

  14. Application of oil-field well log interpretation techniques to the Cerro Prieto Geothermal Field

    Energy Technology Data Exchange (ETDEWEB)

    Ershaghi, I.; Phillips, L.B.; Dougherty, E.L.; Handy, L.L.

    1979-10-01

    An example is presented of the application of oil-field techniques to the Cerro Prieto Field, Mexico. The lithology in this field (sand-shale lithology) is relatively similar to oil-field systems. The study was undertaken as a part of the first series of case studies supported by the Geothermal Log Interpretation Program (GLIP) of the US Department of Energy. The suites of logs for individual wells were far from complete. This was partly because of adverse borehole conditions but mostly because of unavailability of high-temperature tools. The most complete set of logs was a combination of Dual Induction Laterolog, Compensated Formation Density Gamma Ray, Compensated Neutron Log, and Saraband. Temperature data about the wells were sketchy, and the logs had been run under pre-cooled mud condition. A system of interpretation consisting of a combination of graphic and numerical studies was used to study the logs. From graphical studies, evidence of hydrothermal alteration may be established from the trend analysis of SP (self potential) and ILD (deep induction log). Furthermore, the cross plot techniques using data from density and neutron logs may help in establishing compaction as well as rock density profile with depth. In the numerical method, R/sub wa/ values from three different resistivity logs were computed and brought into agreement. From this approach, values of formation temperature and mud filtrate resistivity effective at the time of logging were established.

  15. Experimental investigation into methane hydrate production during three-dimensional thermal stimulation with five-spot well system

    International Nuclear Information System (INIS)

    Wang, Yi; Li, Xiao-Sen; Li, Gang; Zhang, Yu; Li, Bo; Chen, Zhao-Yang

    2013-01-01

    Highlights: • The production behaviors of methane hydrate are obtained in the 3-D simulator. • The thermal stimulation method with a five-spot well is used for hydrate production. • The water and gas production, efficiency, recovery, production rate are analyzed. • The effect of injection rate change on the production behavior is investigated. - Abstract: The cubic hydrate simulator (CHS) is used to study the methane hydrate production behaviors in porous media by the thermal stimulation with a five-spot well system. The hot water injection rates range from 10.0 to 40.0 ml/min. The thermal stimulation process is analyzed, and the conclusions are that the hydrate decomposition boundary moves from the central point to the surroundings gradually and finally covers almost the entire hydrate field in the CHS during the thermal stimulation process. The heat conduction plays a more significant role than the convection for the heat diffusion in the thermal stimulation process. The increasing injection rate of the hot water enhances the rate of hydrate decomposition, shortens the production time, and decreases the water production volumes, while it has little influence on the final gas production volumes. Furthermore, the change of the hot water injection rate (R inj ) has little influence on the final gas recovery, however, the higher R inj leads to the higher average production rate and the lower energy efficiency

  16. Natural attenuation and biosurfactant-stimulated bioremediation of estuarine sediments contaminated with diesel oil.

    Science.gov (United States)

    Bayer, Débora M; Chagas-Spinelli, Alessandra C O; Gavazza, Sávia; Florencio, Lourdinha; Kato, Mario T

    2013-09-01

    We evaluated the bioremediation, by natural attenuation (NA) and by natural attenuation stimulated (SNA) using a rhamnolipid biosurfactant, of estuarine sediments contaminated with diesel oil. Sediment samples (30 cm) were put into 35 cm glass columns, and the concentrations of the 16 polycyclic aromatic hydrocarbons (PAHs) prioritized by the US Environmental Protection Agency were monitored for 111 days. Naphthalene percolated through the columns more than the other PAHs, and, in general, the concentrations of the lower molecular weight PAHs, consisting of two and three aromatic rings, changed during the first 45 days of treatment, whereas the concentrations of the higher molecular weight PAHs, consisting of four, five, and six rings, were more stable. The higher molecular weight PAHs became more available after 45 days, in the deeper parts of the columns (20-30 cm). Evidence of degradation was observed only for some compounds, such as pyrene, with a total removal efficiency of 82 and 78 % in the NA and SNA treatments, respectively, but without significant difference. In the case of total PAH removal, the efficiencies were significantly different of 82 and 67 %, respectively.

  17. Onset of surface stimulated emission at 260 nm from AlGaN multiple quantum wells

    KAUST Repository

    Li, Xiaohang; Xie, Hongen; Ponce, Fernando A.; Ryou, Jae-Hyun; Detchprohm, Theeradetch; Dupuis, Russell D.

    2015-01-01

    We demonstrated onset of deep-ultraviolet (DUV) surface stimulated emission (SE) from c-plane AlGaNmultiple-quantum well(MQW)heterostructuresgrown on a sapphire substrate by optical pumping at room temperature. The onset of SE became observable at a

  18. Theoretical analysis of multiphase flow during oil-well drilling by a conservative model

    Science.gov (United States)

    Nicolas-Lopez, Ruben

    2005-11-01

    In order to decrease cost and improve drilling operations is necessary a better understood of the flow mechanisms. Therefore, it was carried out a multiphase conservative model that includes three mass equations and a momentum equation. Also, the measured geothermal gradient is utilized by state equations for estimating physical properties of the phases flowing. The mathematical model is solved by numerical conservative schemes. It is used to analyze the interaction among solid-liquid-gas phases. The circulating system consists as follow, the circulating fluid is pumped downward into the drilling pipe until the bottom of the open hole then it flows through the drill bit, and at this point formation cuttings are incorporated to the circulating fluid and carried upward to the surface. The mixture returns up to the surface by an annular flow area. The real operational conditions are fed to conservative model and the results are matched up to field measurements in several oil wells. Mainly, flow rates, drilling rate, well and tool geometries are data to estimate the profiles of pressure, mixture density, equivalent circulating density, gas fraction and solid carrying capacity. Even though the problem is very complex, the model describes, properly, the hydrodynamics of drilling techniques applied at oil fields. *Authors want to thank to Instituto Mexicano del Petroleo and Petroleos Mexicanos for supporting this research.

  19. Elasticity and expansion test performance of geopolymer as oil well cement

    Science.gov (United States)

    Ridha, S.; Hamid, A. I. Abd; Halim, A. H. Abdul; Zamzuri, N. A.

    2018-04-01

    History has shown that geopolymer cement provides high compressive strength as compared to Class G cement. However, the research had been done at ambient temperature, not at elevated condition which is the common oil well situation. In this research, the physical and mechanical properties performance of the oil well cement were investigated by laboratory work for two types of cement that are geopolymer and Class G cement. The cement samples were produced by mixing the cement according to the API standards. Class C fly ash was used in this study. The alkaline solution was prepared by mixing sodium silicate with NaOH solution. The NaOH solution was prepared by diluting NaOH pellets with distilled water to 8M. The cement samples were cured at a pressure of 3000 psi and a temperature of 130 °C to simulate the downhole condition. After curing, the physical properties of the cement samples were investigated using OYO Sonic Viewer to determine their elastic properties. Autoclave expansion test and compressive strength tests were conducted to determine the expansion value and the strength of the cement samples, respectively. The results showed that the geopolymer cement has a better physical and mechanical properties as compared with Class G cement at elevated condition.

  20. Volatile organic compound emissions from the oil and natural gas industry in the Uintah Basin, Utah: oil and gas well pad emissions compared to ambient air composition

    Science.gov (United States)

    Warneke, C.; Geiger, F.; Edwards, P. M.; Dube, W.; Pétron, G.; Kofler, J.; Zahn, A.; Brown, S. S.; Graus, M.; Gilman, J. B.; Lerner, B. M.; Peischl, J.; Ryerson, T. B.; de Gouw, J. A.; Roberts, J. M.

    2014-10-01

    Emissions of volatile organic compounds (VOCs) associated with oil and natural gas production in the Uintah Basin, Utah were measured at a ground site in Horse Pool and from a NOAA mobile laboratory with PTR-MS instruments. The VOC compositions in the vicinity of individual gas and oil wells and other point sources such as evaporation ponds, compressor stations and injection wells are compared to the measurements at Horse Pool. High mixing ratios of aromatics, alkanes, cycloalkanes and methanol were observed for extended periods of time and for short-term spikes caused by local point sources. The mixing ratios during the time the mobile laboratory spent on the well pads were averaged. High mixing ratios were found close to all point sources, but gas well pads with collection and dehydration on the well pad were clearly associated with higher mixing ratios than other wells. The comparison of the VOC composition of the emissions from the oil and natural gas well pads showed that gas well pads without dehydration on the well pad compared well with the majority of the data at Horse Pool, and that oil well pads compared well with the rest of the ground site data. Oil well pads on average emit heavier compounds than gas well pads. The mobile laboratory measurements confirm the results from an emissions inventory: the main VOC source categories from individual point sources are dehydrators, oil and condensate tank flashing and pneumatic devices and pumps. Raw natural gas is emitted from the pneumatic devices and pumps and heavier VOC mixes from the tank flashings.

  1. Technical standardization of oil well abandonment: a review of current standards and technologies

    Energy Technology Data Exchange (ETDEWEB)

    Suzart, J. Walter P.; Pessoa, Laudemar; Paiva, Maria [Halliburton Energy Services (HES), Duncan, OK (United States)

    2008-07-01

    The objective of this study is to provide a new methodology for well abandonment. This practice is becoming more and more important because of the increasing number of production fields being abandoned. We strongly recommend a study of cement slurries properties for specific use in temporary and permanent abandonment plugs based on the estimation of the cement slurry hardened when placed in the well. By using specific additives, it is possible to achieve very stable slurries. For example, when permeability is reduced, formation fluid migration can be blocked and chemical reactions between the fluid and the slurry may be inhibited. With this objective, we present a laboratory investigation model and an example of slurry testing recommendation. During the abandonment operation, all records of the well characteristics should be maintained to include the reason for the abandonment, and location of fresh water, brine, and hydrocarbon zones that may exist. This documentation will also allow the analysis of solutions for the problems that originally caused the abandonment of the well. This data could be important for future use by environmental protection commissions to reopen or to drill an adjacent well. Given the high price of oil, it may now be economically feasible to reopen the well, if the reason for abandonment was low productivity. This way, a critical analysis of the current conditions of well and field abandonment in the country is presented. Based on this information, a review of the current standards is suggested. (author)

  2. Characterization of enzymatically extracted sunflower seed oil as well as the protein residues

    Directory of Open Access Journals (Sweden)

    Sitohy, M. Z.

    1993-12-01

    Full Text Available Sunflower seed oil was enzymatically extracted with six different enzymes: cellulase, hemicellulase, animal proteinase, acid proteinase, pectinase and pectinex under the following conditions: substrate concentration in phosphate buffer (0.5M, pH 5 30%, enzyme concentration 2% (E/S, temperature 50°C and time 3 hours. The obtained oils were analyzed for physicochemical properties and fatty acid profiles. The protein residues were analyzed for amino acid compositions. The results showed that the enzymatic extraction with cellulase or hemicellulase could maintain good oil quality of the extracted oils as their levels of linoleic and oleic acids recorded similar values to those of the control oil extracted with organic solvents. Also the level of iodine value was in the same level of control. On the other hand, the use of proteases in the enzymatic extraction of sunflower seed oil caused some reductions in the levels of the unsaturated fatty acids as well as the iodine value. The pectinases showed a similar trend to that of the proteinase with the least recovery of linoleic acid among the different oils under study. Similarly, the use of cellulases did not change the amino acid composition of the protein residue as compared to the control, in the contrary to the extraction with the proteinases which caused reduction of some amino acids from the protein residues especially lysine, leucine, iso-leucine, alanine, arginine and aspartic. In that respect the use of pectinases behaved similar to cellulases.

    Aceite de semilla de girasol fue extraído enzimáticamente con seis enzimas diferentes: celulasa, hemicelulasa, proteinasa animal, proteinase acida, pectinasa y pectinex bajo las condiciones siguientes: concentración de sustrato en tampón fosfato (0,5M, pH 5 30%, concentración enzimática 2% (E/S, temperatura 50°C y tiempo 3 horas. Los aceites obtenidos fueron analizados por sus propiedades fisicoquímicas y perfiles de ácidos grasos

  3. A Computation Fluid Dynamic Model for Gas Lift Process Simulation in a Vertical Oil Well

    Directory of Open Access Journals (Sweden)

    Kadivar Arash

    2017-03-01

    Full Text Available Continuous gas-lift in a typical oil well was simulated using computational fluid dynamic (CFD technique. A multi fluid model based on the momentum transfer between liquid and gas bubbles was employed to simulate two-phase flow in a vertical pipe. The accuracy of the model was investigated through comparison of numerical predictions with experimental data. The model then was used to study the dynamic behaviour of the two-phase flow around injection point in details. The predictions by the model were compared with other empirical correlations, as well. To obtain an optimum condition of gas-lift, the influence of the effective parameters including the quantity of injected gas, tubing diameter and bubble size distribution were investigated. The results revealed that increasing tubing diameter, the injected gas rate and decreasing bubble diameter improve gas-lift performance.

  4. MODELLING AND ANALYSIS OF TOWER INTERVENTION EQUIPMENT OF OIL & GAS WELLS

    Directory of Open Access Journals (Sweden)

    César A. Chagoyén-Méndez

    2015-04-01

    Full Text Available In this paper, the modeling and analysis of one tower Workover Rig belonging to a maintenance facility for oil and gas wells is presented. When performing the maintenance of this tower, it is detected that one of the elements of the structure has some deformation. It was decided not to put it into operation and submit it to research. The modeling of invariants as well as ways of modeling soil structure interaction is discussed. It was necessary to determine the material properties with the performing of test of some samples taken on two components of the tower. The structural behavior of the tower to operating loads are then studied, proving that the effect of the deformed element in the structure is not significant for the stresses to which are subject.

  5. Comparative Risk Assessment of spill response options for a deepwater oil well blowout: Part 1. Oil spill modeling.

    Science.gov (United States)

    French-McCay, Deborah; Crowley, Deborah; Rowe, Jill J; Bock, Michael; Robinson, Hilary; Wenning, Richard; Walker, Ann Hayward; Joeckel, John; Nedwed, Tim J; Parkerton, Thomas F

    2018-05-31

    Oil spill model simulations of a deepwater blowout in the Gulf of Mexico De Soto Canyon, assuming no intervention and various response options (i.e., subsea dispersant injection SSDI, in addition to mechanical recovery, in-situ burning, and surface dispersant application) were compared. Predicted oil fate, amount and area of surfaced oil, and exposure concentrations in the water column above potential effects thresholds were used as inputs to a Comparative Risk Assessment to identify response strategies that minimize long-term impacts. SSDI reduced human and wildlife exposure to volatile organic compounds; dispersed oil into a large water volume at depth; enhanced biodegradation; and reduced surface water, nearshore and shoreline exposure to floating oil and entrained/dissolved oil in the upper water column. Tradeoffs included increased oil exposures at depth. However, since organisms are less abundant below 200 m, results indicate that overall exposure of valued ecosystem components was minimized by use of SSDI. Copyright © 2018 Elsevier Ltd. All rights reserved.

  6. Movement of the water-oil contact during operation of a single well in an inclined stratum

    Energy Technology Data Exchange (ETDEWEB)

    Kazymov, A Sh

    1965-01-01

    In this theoretical study the author develops equations which describe the movement of an oil-water interface toward a single well in an inclined stratum. The equations apply even if viscosities, densities, and permeabilities vary from place to place.

  7. Improving reservoir history matching of EM heated heavy oil reservoirs via cross-well seismic tomography

    KAUST Repository

    Katterbauer, Klemens; Hoteit, Ibrahim

    2014-01-01

    process. While becoming a promising technology for heavy oil recovery, its effect on overall reservoir production and fluid displacements are poorly understood. Reservoir history matching has become a vital tool for the oil & gas industry to increase

  8. Two-phase flow in volatile oil reservoir using two-phase pseudo-pressure well test method

    Energy Technology Data Exchange (ETDEWEB)

    Sharifi, M.; Ahmadi, M. [Calgary Univ., AB (Canada)

    2009-09-15

    A study was conducted to better understand the behaviour of volatile oil reservoirs. Retrograde condensation occurs in gas-condensate reservoirs when the flowing bottomhole pressure (BHP) lowers below the dewpoint pressure, thus creating 4 regions in the reservoir with different liquid saturations. Similarly, when the BHP of volatile oil reservoirs falls below the bubblepoint pressure, two phases are created in the region around the wellbore, and a single phase (oil) appears in regions away from the well. In turn, higher gas saturation causes the oil relative permeability to decrease towards the near-wellbore region. Reservoir compositional simulations were used in this study to predict the fluid behaviour below the bubblepoint. The flowing bottomhole pressure was then exported to a well test package to diagnose the occurrence of different mobility regions. The study also investigated the use of a two-phase pseudo-pressure method on volatile and highly volatile oil reservoirs. It was concluded that this method can successfully predict the true permeability and mechanical skin. It can also distinguish between mechanical skin and condensate bank skin. As such, the two-phase pseudo-pressure method is particularly useful for developing after-drilling well treatment and enhanced oil recovery process designs. However, accurate relative permeability and PVT data must be available for reliable interpretation of the well test in volatile oil reservoirs. 18 refs., 3 tabs., 9 figs.

  9. Casing Pipe Damage Detection with Optical Fiber Sensors: A Case Study in Oil Well Constructions

    Directory of Open Access Journals (Sweden)

    Zhi Zhou

    2010-01-01

    Full Text Available Casing pipes in oil well constructions may suddenly buckle inward as their inside and outside hydrostatic pressure difference increases. For the safety of construction workers and the steady development of oil industries, it is critically important to measure the stress state of a casing pipe. This study develops a rugged, real-time monitoring, and warning system that combines the distributed Brillouin Scattering Time Domain Reflectometry (BOTDR and the discrete fiber Bragg grating (FBG measurement. The BOTDR optical fiber sensors were embedded with no optical fiber splice joints in a fiber-reinforced polymer (FRP rebar and the FBG sensors were wrapped in epoxy resins and glass clothes, both installed during the segmental construction of casing pipes. In situ tests indicate that the proposed sensing system and installation technique can survive the downhole driving process of casing pipes, withstand a harsh service environment, and remain intact with the casing pipes for compatible strain measurements. The relative error of the measured strains between the distributed and discrete sensors is less than 12%. The FBG sensors successfully measured the maximum horizontal principal stress with a relative error of 6.7% in comparison with a cross multipole array acoustic instrument.

  10. Well blowout rates in California Oil and Gas District 4--Update and Trends

    Energy Technology Data Exchange (ETDEWEB)

    Jordan, Preston D.; Benson, Sally M.

    2009-10-01

    Well blowouts are one type of event in hydrocarbon exploration and production that generates health, safety, environmental and financial risk. Well blowouts are variously defined as 'uncontrolled flow of well fluids and/or formation fluids from the wellbore' or 'uncontrolled flow of reservoir fluids into the wellbore'. Theoretically this is irrespective of flux rate and so would include low fluxes, often termed 'leakage'. In practice, such low-flux events are not considered well blowouts. Rather, the term well blowout applies to higher fluxes that rise to attention more acutely, typically in the order of seconds to days after the event commences. It is not unusual for insurance claims for well blowouts to exceed US$10 million. This does not imply that all blowouts are this costly, as it is likely claims are filed only for the most catastrophic events. Still, insuring against the risk of loss of well control is the costliest in the industry. The risk of well blowouts was recently quantified from an assembled database of 102 events occurring in California Oil and Gas District 4 during the period 1991 to 2005, inclusive. This article reviews those findings, updates them to a certain extent and compares them with other well blowout risk study results. It also provides an improved perspective on some of the findings. In short, this update finds that blowout rates have remained constant from 2005 to 2008 within the limits of resolution and that the decline in blowout rates from 1991 to 2005 was likely due to improved industry practice.

  11. Enhancing oil rate in solvent vapour extraction processes through tee-well pattern

    Energy Technology Data Exchange (ETDEWEB)

    Zeng, F.; Knorr, K.D.; Wilton, R.R. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[Saskatchewan Research Council, Saskatoon, SK (Canada)

    2008-10-15

    In order for the vapour extraction (VAPEX) process to be considered commercially viable, the production flow rate in classical VAPEX must be increased. The low flow rate can be attributed to the fact that the classical VAPEX process uses forces of buoyancy to distribute the solvent and gravity to drain the diluted oil to the producer. This paper presented a new well pattern, referred to as the tee-SVX process, that may enhance the oil flow rate two to ten times over the classical approach. Additional horizontal injectors, perpendicular to the injector and the producer in classical VAPEX were placed in the top-most region of the reservoir in the new well pattern. The paper described the model development which involved conducting a series of simulation runs in order to evaluate the performance of the new well pattern. The paper also presented a comparison of the performance of the tee-SVX and the classical VAPEX and lateral-SVX. A sensitivity analysis was also performed to further evaluate the performance of tee-SVX and provide the boundaries of the application of the process. Two types of factors affecting the performance of tee-SVX were outlined, notably design factors; and formation and fluid uncertainties. The performance of tee-SVX in thinner reservoirs and in reservoirs with a gas cap were also examined. It was concluded that compared with the lateral-SVX process, the tee-SVX process could significantly reduce the time to solvent breakthrough. 12 refs., 2 tabs., 30 figs.

  12. Marathon's imaging of Bakken fracture stimulations : NDIC oil and gas petroleum research program grants

    Energy Technology Data Exchange (ETDEWEB)

    Brimberry, D. [Marathon Oil Corp., Houston, TX (United States)

    2009-07-01

    This presentation discussed surface tiltmeter and microseismic studies conducted to image fracture stimulations at the Bakken formation. The aim of the studies was to map the fracture stimulation network of the Bakken formation, which has highly sensitive surface levels. The study determined the best fit theoretical deformation after stimulation. Stimulations from 2007 and 2006 were compared in order to determine time lapses as well as to understand data limitations and differences in time and production between jobs. The microseismic study used seismic arrays deployed at the surface of horizontal open hole wells. Data from the studies indicated the presence of a complex network. While data utility was good, noise prevented the precise location of events. The study demonstrated that both tiltmeter and microseismic technology can be used to plan well stimulation project. Data from the study can be applied in other areas in the Williston Basin. tabs., figs.

  13. Study on perfume stimulating olfaction with volatile oil of Acorus gramineus for treatment of the Alzheimer's disease rat.

    Science.gov (United States)

    Liu, Zhi-Bin; Niu, Wen-Min; Yang, Xiao-Hang; Wang, Yuan; Wang, Wei-Gang

    2010-12-01

    To probe into the therapeutic effect of perfume stimulating olfaction with volatile oil of Acorus Gramineus on the Alzheimer's disease (AD) rat. Totally 50 adult SD rats, male,weighing 300 +/- 10 g, were randomly divided into 5 groups, normal group (group A), olfactory nerve severing model group (group B), AD model group (group C), AD model plus perfume stimulation group (group D), AD model olfactory nerve severing plus perfume stimulation group (group E), 10 rats in each group. After perfume stimulation, Morris maze test was conducted for valuating the learning and memory ability; Malondaldehyde (MDA) content, and superoxide dismutase (SOD) and glutathione peroxidase (GSH-Px) activities in the brain, and the brain weight were detected. Compared with the AD model group, the average escape latency and swimming distance in 6 days were significantly shorter than those in the group A, B, D (P 0.05); Compared with the group A, B and D, MDA content in the group C significantly increased (P 0.05). Perfume stimultating olfaction with volatile oil of Acorus Gramineus can significantly increase the learning-memory ability, decrease MDA content and increase SOD and GSH-Px activities and weight of brain in AD rats.

  14. Identification of carbonate reservoirs based on well logging data for boreholes drilled using oil base muds

    International Nuclear Information System (INIS)

    Abdukhalikov, Ya.N; Serebrennikov, V.S.

    1979-01-01

    Experiment on carbonate reservoir identification according to well logging data for boreholes drilled using oil base muds is described. Pulse neutron-neutron logging (PNNL) was widely used at the territory of Pripyat' hole to solve the task. To evaluate volumetric clayiness of carbonate rocks the dependence of gamma-logging, that is data of gamma-logging against clayey rocks built for every hollow, is used. Quantitative estimation of clayiness of dense and clayey carbonate rocks-non-reservoirs is carried out on the basis of the data of neutron-gamma and acoustic logging. Porosity coefficient and lithological characteristic of rocks are also determined according to the data of acoustic and neutron gamma-logging

  15. Characteristics and properties of oil-well cements auditioned with blast furnace slag

    International Nuclear Information System (INIS)

    Sanchez, R.; Palacios, M.; Puertas, F.

    2011-01-01

    The present paper addresses the alkali activation of Portland cements containing blast furnace slag (20 and 30% by cement weight) with a view to the possible use of these materials in oil well construction. The hydration studies conducted showed that in cement/slag blends, the sodium silicate activator partially inhibited the dissolution of the silicate phases in the Portland cement, retarding cement hydration and reducing the precipitation of reaction products. Due to such partial inhibition, the cement/slag blends had significantly lower mechanical strength than Portland cements hydrated with water. 2 9Si and 2 7Al MAS NMR and BSE/EDX studies, in turn, showed that the CSH gel forming in the alkali-activated cement/slag pastes contained Al in tetrahedral positions and low Ca/Si ratios. (Author) 29 refs.

  16. High-performance computing on GPUs for resistivity logging of oil and gas wells

    Science.gov (United States)

    Glinskikh, V.; Dudaev, A.; Nechaev, O.; Surodina, I.

    2017-10-01

    We developed and implemented into software an algorithm for high-performance simulation of electrical logs from oil and gas wells using high-performance heterogeneous computing. The numerical solution of the 2D forward problem is based on the finite-element method and the Cholesky decomposition for solving a system of linear algebraic equations (SLAE). Software implementations of the algorithm used the NVIDIA CUDA technology and computing libraries are made, allowing us to perform decomposition of SLAE and find its solution on central processor unit (CPU) and graphics processor unit (GPU). The calculation time is analyzed depending on the matrix size and number of its non-zero elements. We estimated the computing speed on CPU and GPU, including high-performance heterogeneous CPU-GPU computing. Using the developed algorithm, we simulated resistivity data in realistic models.

  17. Cement for oil well developed from ordinary cement: characterization physical, chemical and mineralogical

    International Nuclear Information System (INIS)

    Oliveira, D.N.S.; Neves, G. de A.; Chaves, A.C.; Mendonca, A.M.G.D.; Lima, M.S. de; Bezerra, U.T.

    2012-01-01

    This work aims to characterize a new type of cement produced from the mixture of ordinary Portland cement, which can be used as an option in the cementing of oil wells. To enable this work we used the method of lineal programming for the new cement composition, then conducted tests to characterize through particle size analysis by laser diffraction, chemical analysis by EDX, TGA, X-ray diffraction, time grip, resistance to compression. The overall result showed that the new cement had made low-C3A, takes more time to the CPP, thermal stability up to 500 ° C, the kinetics of hydration and low levels of major components consistent with the specifications of ABNT. (author)

  18. The effect of gas and oil well blowout emissions on livestock in Alberta

    International Nuclear Information System (INIS)

    Beck, B.E.

    1992-01-01

    Poisoning caused by emissions from sour gas well or oil well blowouts is not acute because the gases are diluted by the atmosphere before they reach livestock. Exposure may last a month or more and may produce a syndrome indistinguishable from common disorders of flu, malaise, mood change, and in the case of animals, lack of production or decreased production. Little information is available on the composition of releases from well blowouts, which may change due to concurrent reactions with oxygen and photodecomposition. Effects on livestock observed to results from sour gas plant emissions (mostly sulfur dioxide) include runny eyes in cattle, loss of production, diarrhea and abortion. Blowout emissions may contain oxidant gases as well as hydrogen sulfides. These products irritate mucous membranes, and can lead to pink eye. Respiratory problems may include upper respiratory tract infections, and may produce susceptibility to secondary pneumonia. Abortion, infertility and congenital effects are areas of concern. It is considered unlikely that hydrogen sulfide can cause such effects, however carbon disulfide and carbonyl sulfide, both present in sour gas blowouts, are known to have effects on the fetus. Effects on production and performance are unknown, and it is postulated that amounts of sulfur deposition are insufficient to cause nutrient deficiencies. Psychological reactions are suggested to explain some of the adverse effects of exposure to sour gas. 1 ref

  19. Application of flexible slurries: an alternative for oil wells subject to cyclic steam injection

    Energy Technology Data Exchange (ETDEWEB)

    Suzart, J. Walter P.; Paiva, Maria D.M.; Cunha, Marcelo C.S. [Halliburton Energy Services (HES), Duncan, OK (United States); Farias, Antonio Carlos [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)

    2008-07-01

    Oil wells that receive cyclic steam injection are subject to high temperature variations during their life cycle. This causes volumetric expansion of the metallic casing which leads to cracks and channels in the formation of the cement. Studies show that volumetric expansion caused by temperature variation may cause wells to rise up to 20-in. at the surface. This paper presents alternative materials that improve the elastic properties of set cement slurries, focusing on maintaining sufficient resilience to maximize the life of the cement. We compare a set of fourteen formulations, some currently in use, selecting those with high flexibility. Analysis was based on the mechanical properties of the set slurries as well as tests according to standards from ABNT and from API Spec 10B. This work contributes new formulations for wells that under-go cyclic steam injection. These new formulations are presented as alternatives to current flexible slurry technology. We can obtain high-quality, more resilient slurries using materials that are more economical, have better cost-benefit, and are easily available in the market. (author)

  20. Low parameter model to monitor bottom hole pressure in vertical multiphase flow in oil production wells

    Directory of Open Access Journals (Sweden)

    Mohammad Ali Ahmadi

    2016-09-01

    Full Text Available The importance of the flow patterns through petroleum production wells proved for upstream experts to provide robust production schemes based on the knowledge about flow behavior. To provide accurate flow pattern distribution through production wells, accurate prediction/representation of bottom hole pressure (BHP for determining pressure drop from bottom to surface play important and vital role. Nevertheless enormous efforts have been made to develop mechanistic approach, most of the mechanistic and conventional models or correlations unable to estimate or represent the BHP with high accuracy and low uncertainty. To defeat the mentioned hurdle and monitor BHP in vertical multiphase flow through petroleum production wells, inventive intelligent based solution like as least square support vector machine (LSSVM method was utilized. The evolved first-break approach is examined by applying precise real field data illustrated in open previous surveys. Thanks to the statistical criteria gained from the outcomes obtained from LSSVM approach, the proposed least support vector machine (LSSVM model has high integrity and performance. Moreover, very low relative deviation between the model estimations and the relevant actual BHP data is figured out to be less than 6%. The output gained from LSSVM model are closed the BHP while other mechanistic models fails to predict BHP through petroleum production wells. Provided solutions of this study explicated that implies of LSSVM in monitoring bottom-hole pressure can indicate more accurate monitoring of the referred target which can lead to robust design with high level of reliability for oil and gas production operation facilities.

  1. High-temperature explosive development for geothermal well stimulation. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Schmidt, E.W.; Mars, J.E.; Wang, C.

    1978-03-31

    A two-component, temperature-resistant liquid explosive called HITEX has been developed which is capable of withstanding 561/sup 0/K (550/sup 0/F) for 24 hours in a geothermal environment. The explosive is intended for the stimulation of nonproducing or marginally producing geothermal (hot dry rock, vapor-dominated or hydrothermal) reservoirs by fracturing the strata in the vicinity of a borehole. The explosive is inherently safe because it is mixed below ground downhole from two nondetonable liquid components. Development and safety tests included differential scanning calorimetry, thermal stability, minerals compatibility, drop-weight sensitivity, adiabatic compression, electrostatic discharge sensitivity, friction sensitivity, detonation arrest capability, cook-off tests, detonability at ambient and elevated pressure, detonation velocity and thin film propagation in a wedge.

  2. Effect of rheology on flow displacement during cementing process in oil wells

    Energy Technology Data Exchange (ETDEWEB)

    Braghini, Andre; Naccache, Monica F.; Fonseca, Marcos I. [Dept. Mechanical Engineering. Pontificia Universidade Catolica (PUR-Rio), Rio de Janeiro, RJ (Brazil)], e-mails: mnaccache@puc-rio.br; Miranda, Cristiane R. de; Martins, Andre L.; Aranha, Pedro E. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)], e-mails: crisrichard@petrobras.com.br, aleibsohn@petrobras.com.br, pearanha@petrobras.com.br

    2010-07-01

    This paper describes a set of numerical simulations of the displacement flow of three non-Newtonian fluids through annular eccentric wells. The main application of this work is the studying of drilling and completion processes of oil wells where a cement slurry pushes the drilling mud, used in the drilling process to lubricate the drill and to remove the produced drilling cuts. To avoid contamination, a spacer fluid is usually inserted between them. Both drilling mud and cement slurry behave as non-Newtonian fluids, and the spacer fluid can be Newtonian or non-Newtonian. The analysis of flow and interface configuration between these fluids helps to determine contamination, and is an important tool for the process optimization. The numerical solution of the governing conservation equations of mass and momentum is obtained with the Fluent software, using the finite volume technique and the volume of fluid method. The effects of rheological parameters, density ratios and pumped volume of the spacer fluid are investigated. The results obtained show that the displacement is better when a more viscous spacer fluid is used. The results also show that using lower amounts of the spacer fluid can lead to contamination, which is worse in the smaller gap region of the annular space, in the case of non-rectilinear well. It was also observed that the density ratios play a major role in the cementing operation. (author)

  3. Status report No. 8: State uses of Exxon and Stripper Well oil overcharge funds

    International Nuclear Information System (INIS)

    Gonzales, H.; Claytor, C.P.

    1991-07-01

    From March of 1986 through early January, 1991 (when the report surveying began) state governments received $3.423 billion in funds obtained by the federal government through two major cases, based on price overcharges committed by numerous oil companies during the period of price controls, between 1973 and 1981. Furthermore, about another $1 billion may still be collected from oil companies, with roughly 1/2 to be distributed to the states (and the other 1/2 to the federal government), over the next 5 to 10 years. The role of state governments is to allocate the funds, within the specific case guidelines, to new or existing energy programs, in a way which is designed to benefit (or provide restitution to) the class or classes of purchasers who bore the burden of the overcharges. This report incorporates information collected by NCLC through telephone surveys conducted from January through March 1991. The information we collected on the status and state uses of both Exxon and Stripper Well funds is contained in the state-by-state narrative summary selection and in a series of tables at the end of the report. Each of the quarterly reports tracks final state decisions allocating use of these funds. The terms ''allocated'' and ''designated'' are used interchangeably throughout the document to mean that final state decisions have been made regarding these funds. Tracking state allocations about these funds is the only practical way for us to provide an overview of the actual status of state processes or decisions which have occurred with regard to this money. 9 tabs

  4. Dietary fish oil stimulates hepatic low density lipoprotein transport in the rat.

    Science.gov (United States)

    Ventura, M A; Woollett, L A; Spady, D K

    1989-01-01

    These studies were undertaken to examine the effect of fish oil, safflower oil, and hydrogenated coconut oil on the major processes that determine the concentration of low density lipoprotein (LDL) in plasma, i.e., the rate of LDL production and the rates of receptor-dependent and receptor-independent LDL uptake in the various organs of the body. When fed at the 20% level, fish oil reduced plasma LDL-cholesterol levels by 38% primarily by increasing LDL receptor activity in the liver. Dietary safflower oil also increased hepatic LDL receptor activity; however, since the rate of LDL production also increased, plasma LDL-cholesterol levels remained essentially unchanged. Hydrogenated coconut oil had no effect on LDL receptor activity but increased the rate of LDL-cholesterol production causing plasma LDL-cholesterol levels to increase 46%. Dietary fish oil had no effect on the receptor-dependent transport of asialofetuin by the liver, suggesting that the effect of fish oil on hepatic LDL receptor activity was specific and not due to a generalized alteration in the physical properties of hepatic membranes. Finally, dietary fish oil increased hepatic cholesteryl ester levels and suppressed hepatic cholesterol synthesis rates, suggesting that the up-regulation of hepatic LDL receptor activity in these animals was not simply a response to diminished cholesterol availability in the liver. PMID:2760200

  5. Kinetic modeling of cement slurry synthesized with Henna extract in oil well acidizing treatments

    Directory of Open Access Journals (Sweden)

    Amir Hossein Aghajafari

    2016-06-01

    Full Text Available Acidizing treatment in petroleum reservoirs is a short-term and viable strategy to preserve the productivity of a well. There is a major concern for the degradation of cement sheath integrity, leading to poor zonal isolation and environmental issues. Therefore, it is essential to understand how the cement behaves when attacked by hydrochloric acid. In this study, a cement slurry by incorporation of the Henna extract, as an environmentally friendly cement additive, was synthesized as a potential solution to solve this problem. The characteristics of the treated cement slurry were compared with a reference slurry (w/c = 0.44 which is composed of only cement and water. A kinetic study was carried out to evaluate the adsorption behavior of the cement slurries exposed to an acid solution with 0.1 M HCl in a range of 25 to 55 °C conditions. The features of the cement slurries were evaluated by multiple analytical techniques such as XRD, FTIR, TG, and DSC analysis. From the experimental data, it is concluded that the second-order Lagergren kinetic model revealed to be the best in describing kinetic isotherms taken, because the margin between experimental and calculated values was minor for this model. The results of the characterization and HCl interaction kinetic studies underlined the prominent protective role of Henna extract-modified cement slurry in the enhancement of the cement resistance against acid attack and utilization in environmentally favorable oil well acidizing treatments.

  6. Oil release from Macondo well MC252 following the Deepwater Horizon accident.

    Science.gov (United States)

    Griffiths, Stewart K

    2012-05-15

    Oil flow rates and cumulative discharge from the BP Macondo Prospect well in the Gulf of Mexico are calculated using a physically based model along with wellhead pressures measured at the blowout preventer (BOP) over the 86-day period following the Deepwater Horizon accident. Parameters appearing in the model are determined empirically from pressures measured during well shut-in and from pressures and flow rates measured the preceding day. This methodology rigorously accounts for ill-characterized evolution of the marine riser, installation and removal of collection caps, and any erosion at the wellhead. The calculated initial flow rate is 67,100 stock-tank barrels per day (stbd), which decays to 54,400 stbd just prior to installation of the capping stack and subsequent shut-in. The calculated cumulative discharge is 5.4 million stock-tank barrels, of which 4.6 million barrels entered the Gulf. Quantifiable uncertainties in these values are -9.3% and +7.5%, yielding a likely total discharge in the range from 4.9 to 5.8 million barrels. Minimum and maximum credible values of this discharge are 4.6 and 6.2 million barrels. Alternative calculations using the reservoir and sea-floor pressures indicate that any erosion within the BOP had little affect on cumulative discharge.

  7. SMART MONITORING AND DECISION MAKING FOR REGULATING ANNULUS BOTTOM HOLE PRESSURE WHILE DRILLING OIL WELLS

    Directory of Open Access Journals (Sweden)

    M. P. Vega

    Full Text Available Abstract Real time measurements and development of sensor technology are research issues associated with robustness and safety during oil well drilling operations, making feasible the diagnosis of problems and the development of a regulatory strategy. The major objective of this paper is to use an experimental plant and also field data, collected from a basin operation, offshore Brazil, for implementing smart monitoring and decision making, in order to assure drilling inside operational window, despite the commonly observed disturbances that produce fluctuations in the well annulus bottom hole pressure. Using real time measurements, the performance of a continuous automated drilling unit is analyzed under a scenario of varying levels of rate of penetration; aiming pressure set point tracking (inside the operational drilling window and also rejecting kick, a phenomenon that occurs when the annulus bottom hole pressure is inferior to the porous pressure, producing the migration of reservoir fluids into the annulus region. Finally, an empirical model was built, using real experimental data from offshore Brazil basins, enabling diagnosing and regulating a real drilling site by employing classic and advanced control strategies.

  8. Numerical investigation of the prospects of high energy laser in drilling oil and gas wells

    International Nuclear Information System (INIS)

    Agha, K.R.; Belhaj, H.A.; Mustafiz, S.; Islam, M.R.; Bjorndalen, N.

    2004-01-01

    Rotary drilling is the primary method used to reach oil and gas formations that was developed over a century ago. Many problems persist with this method, including downtime due to dull bits, the lack of precise vertical or horizontal wells and formation fluid leakage during drilling due to the lack of a seal around the hole. Laser drilling is a new technology that has been proposed as a method to eliminate the current problems while drilling and provide a less expensive alternative to conventional methods. This paper discussed the development of a numerical model based on the fundamental heat transfer and fluid flow phenomena including conduction, melting and vaporization responsible for material removal by laser drilling process. The paper addressed the thermal process involved in laser drilling of sandstone and limestone rocks as well as aluminum and mild steel. The paper outlined the parametric study and discussed the design considerations for a field application. Economical and environmental impacts were also included. It was concluded that more experimental investigation is needed to fully understand the laser operation and to enhance the integrity of the numerical models. In addition, it was concluded that field equipment must be designed to meet the changes in drilling requirements. 19 refs., 10 figs

  9. Numerical simulation of Class 3 hydrate reservoirs exploiting using horizontal well by depressurization and thermal co-stimulation

    International Nuclear Information System (INIS)

    Yang, Shengwen; Lang, Xuemei; Wang, Yanhong; Wen, Yonggang; Fan, Shuanshi

    2014-01-01

    Highlights: • Depressurization and thermal co-stimulation using horizontal well were proposed. • 3D stimulation showed that gas release rate was 3 × 10 5 m 3 per day within 450 days. • 2D stimulation showed that Class 3 hydrates could be dissociated within 8500 days. • 2D Simulation showed that heat flow was 1620 W lasting 1500 days, and decreased fast. • 1.1× 10 5 kg water was collected within 2000 days and then no more water was produced. - Abstract: Class 3 hydrate reservoirs exploiting using horizontal well by depressurization and thermal co-stimulation was simulated using the HydarteResSim code. Results showed that more than 20% of hydrates in the reservoirs had been dissociated within 450 days at the well temperature of 42 °C and well pressure of 0.1P 0 , 0.2P 0 (P 0 is the initial pressure of the reservoirs, simplifying 42 °C and 0.1P 0 , 42 °C and 0.2P 0 ). While the production behavior of 42 °C and 0.5P 0 , 42 °C and 0.8P 0 were not so exciting. In order to understand the production character of the well in long term, the cross section of 1 m length reservoirs was simulated. Simulation results showed that 4.5 × 10 5 m 3 gas would be collected within 4500 days and 1.1 × 10 6 kg water could be produced within 1500 days in the well at 42 °C and 0.1P 0 . 3.5 × 10 5 m 3 gas would be collected within 8500 days and 1.1 × 10 6 kg water could be produced within 1500 days in the well at 42 °C and 0.2P 0 . The heat flow was 1620 W at the beginning and then decreased rapidly in the two cases. For reservoirs of 1495.2 m in length, about 6.7 × 10 8 m 3 and 5.3 × 10 8 m 3 gas would be collected in the well corresponding to conditions of 42 °C and 0.1P 0 , and 42 °C and 0.2P 0

  10. Long-wavelength stimulated emission and carrier lifetimes in HgCdTe-based waveguide structures with quantum wells

    Energy Technology Data Exchange (ETDEWEB)

    Rumyantsev, V. V., E-mail: rumyantsev@ipm.sci-nnov.ru; Fadeev, M. A.; Morozov, S. V.; Dubinov, A. A.; Kudryavtsev, K. E.; Kadykov, A. M. [Russian Academy of Sciences, Institute for Physics of Microstructures (Russian Federation); Tuzov, I. V. [Lobachevsky State University of Nizhny Novgorod (NNSU) (Russian Federation); Dvoretskii, S. A.; Mikhailov, N. N. [Russian Academy of Sciences, Institute for Semiconductor Physics, Siberian Branch (Russian Federation); Gavrilenko, V. I. [Novosibirsk State University (Russian Federation); Teppe, F. [Universite Montpellier II, Laboratoire Charles Coulomb (L2C) (France)

    2016-12-15

    The interband photoconductivity and photoluminescence in narrow-gap HgCdTe-based waveguide structures with quantum wells (QWs) (designed for long-wavelength stimulated emission under optical pumping) are investigated. The photoconductivity relaxation times in n-type structures reach several microseconds, due to which stimulated emission at a wavelength of 10.2 μm occurs at a low threshold pump intensity (~100 W/cm{sup 2}) at 20 K. In the p-type structures obtained by annealing (to increase the mercury vacancy concentration), even spontaneous emission from the QWs is not detected because of a dramatic decrease in the carrier lifetime with respect to Shockley–Read–Hall nonradiative recombination.

  11. 78 FR 17835 - Approval and Promulgation of Federal Implementation Plan for Oil and Natural Gas Well Production...

    Science.gov (United States)

    2013-03-22

    ...: One commenter stated that the EPA needs to control air quality because hydraulic fracturing (``fracking'') is under-regulated. Response: The majority of oil and natural gas wells drilled today are hydraulically fractured. Hydraulic fracturing occurs when wells are being completed and recompleted. NSPS OOOO...

  12. Chicxulub Impact Crater and Yucatan Carbonate Platform - PEMEX Oil Exploratory Wells Revisited

    Science.gov (United States)

    Pérez-Drago, G.; Gutierrez-Cirlos, A. G.; Pérez-Cruz, L.; Urrutia-Fucugauchi, J.

    2008-12-01

    Geophysical oil exploration surveys carried out by PEMEX in the 1940's revealed occurrence of an anomalous pattern of semi-circular concentric gravity anomalies. The Bouguer gravity anomalies covered an extensive area over the flat carbonate platform in the northwestern Yucatan Peninsula; strong density contrasts were suggestive of a buried igneous complex or basement uplift beneath the carbonates, which was referred as the Chicxulub structure. The exploration program carried out afterwards included a drilling program, starting with Chicxulub-1 well in 1952 and comprising eight deep boreholes through the 1970s. An aeromagnetic survey in late 1970's showed high amplitude anomalies in the gravity anomaly central sector. Thus, research showing Chicxulub as a large complex impact crater formed at the K/T boundary was built on the PEMEX decades-long exploration program. Despite frequent reference to PEMEX information and samples, original data and cores have not been openly available for detailed evaluation and integration with results from recent investigations. Core samples largely remain to be analyzed and interpreted in the context of recent marine, aerial and terrestrial geophysical surveys and the drilling/coring projects of UNAM and ICDP. In this presentation we report on the stratigraphy and paleontological data for PEMEX wells: Chicxulub- 1 (1582m), Sacapuc-1 (1530m), Yucatan-6 (1631m), Ticul-1 (3575m) Yucatan-4 (2398m), Yucatan-2 (3474m), Yucatan-5A (3003m) and Yucatan-1 (3221m). These wells remain the deepest drilled in Chicxulub, providing samples of impact lithologies, carbonate sequences and basement, which give information on post- and pre-impact stratigraphy and crystalline basement. We concentrate on stratigraphic columns, lateral correlations and integration with UNAM and ICDP borehole data. Current plans for deep drilling in Chicxulub crater target the peak ring and central sector, with offshore and onshore boreholes proposed to the IODP and ICDP

  13. Cross-well 4-D resistivity tomography localizes the oil-water encroachment front during water flooding

    Science.gov (United States)

    Zhang, J.; Revil, A.

    2015-04-01

    The early detection of the oil-water encroachment front is of prime interest during the water flooding of an oil reservoir to maximize the production of oil and to avoid the oil-water encroachment front to come too close to production wells. We propose a new 4-D inversion approach based on the Gauss-Newton approach to invert cross-well resistance data. The goal of this study is to image the position of the oil-water encroachment front in a heterogeneous clayey sand reservoir. This approach is based on explicitly connecting the change of resistivity to the petrophysical properties controlling the position of the front (porosity and permeability) and to the saturation of the water phase through a petrophysical resistivity model accounting for bulk and surface conductivity contributions and saturation. The distributions of the permeability and porosity are also inverted using the time-lapse resistivity data in order to better reconstruct the position of the oil water encroachment front. In our synthetic test case, we get a better position of the front with the by-products of porosity and permeability inferences near the flow trajectory and close to the wells. The numerical simulations show that the position of the front is recovered well but the distribution of the recovered porosity and permeability is only fair. A comparison with a commercial code based on a classical Gauss-Newton approach with no information provided by the two-phase flow model fails to recover the position of the front. The new approach could be used for the time-lapse monitoring of various processes in both geothermal fields and oil and gas reservoirs using a combination of geophysical methods.

  14. A New Way to Calculate Flow Pressure for Low Permeability Oil Well with Partially Penetrating Fracture

    Directory of Open Access Journals (Sweden)

    Xiong Ping

    2018-01-01

    Full Text Available In order to improve the validity of the previous models on calculating flow pressure for oil well with partially perforating fracture, a new physical model that obeys the actual heterogeneous reservoir characteristics was built. Different conditions, including reservoir with impermeable top and bottom borders or the reservoir top which has constant pressure, were considered. Through dimensionless transformation, Laplace transformation, Fourier cosine transformation, separation of variables, and other mathematical methods, the analytical solution of Laplace domain was obtained. By using Stephenson numerical methods, the numerical solution pressure in a real domain was obtained. The results of this method agree with the numerical simulations, suggesting that this new method is reliable. The following sensitivity analysis showed that the pressure dynamic linear flow curve can be divided into four flow streams of early linear flow, midradial flow, advanced spherical flow, and border controlling flow. Fracture length controls the early linear flow. Permeability anisotropy significantly affects the midradial flow. The degree of penetration and fracture orientation dominantly affect the late spherical flow. The boundary conditions and reservoir boundary width mainly affect the border controlling flow. The method can be used to determine the optimal degree of opening shot, vertical permeability, and other useful parameters, providing theoretical guidance for reservoir engineering analysis.

  15. New reclamation standards for oil and gas well sites and pipelines in the agricultural land reserve

    International Nuclear Information System (INIS)

    Jones, P.

    1995-01-01

    Reclamation standards are a necessity because of increasing density of oil and gas developments, and the number of wells which may be abandoned over the next few years. All petroleum industry users of land are subject to the Agricultural Land Commission Act and require the approval of the Commission. The new General Order 293/95 was discussed, the purpose of which is to streamline existing regulations and to clarify reclamation standards. The new standards are similar to requirements currently in place in northwestern Alberta because landforms, soils, and land there are similar to those that exist in the Peace River region of B.C. Adopting similar requirements also has the added benefit of providing consistency for the industry between adjacent jurisdictions. In essence, the official view is that petroleum developments are temporary activities as long as the land is restored to its original or better condition, and the disruption to farm operations is minimal. Major provisions of General Order 293/95 were reviewed. It was noted that site contamination and the disposal of wastes were not addressed in the General Order. The reason for this is that these matters fall under the jurisdiction of other government agencies. 7 refs

  16. Sedimentary petrology of oil well rock cores; Petrologia sedimentaria de nucleos de rocas de pozos petroleros

    Energy Technology Data Exchange (ETDEWEB)

    Izquierdo M, Georgina; Paredes S, Adriana [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

    2001-07-01

    At the request of PEMEX Exploration and Production (PEP), in the area of Geology of the Gerencia de Geotermia, the necessary methodology has been integrated to carry out the geologic characterization of cores obtained during the oil well drilling. The integrated studies have been of utility for PEMEX, because they provide detailed information on the processes, conditions of deposition and diagenesis that occur in sedimentary rocks. On the other hand, this geologic information contributes to the update of the geologic model of the field in study. [Spanish] A solicitud de PEMEX Exploracion y Produccion (PEP), en el area de Geologia de la Gerencia de Geotermia, se ha integrado la metodologia necesaria para llevar a cabo la caracterizacion geologica de nucleos obtenidos durante la perforacion de pozos petroleros. Los estudios integrados han sido de utilidad para PEMEX, pues proporcionan informacion detallada sobre los procesos, condiciones de depositacion y diagenesis que ocurren en rocas sedimentarias. Por otro lado, esta informacion geologica contribuye a la actualizacion del modelo geologico del campo en estudio.

  17. Lapland longspur mortality at an oil well drilling rig site, Laramie County, Wyoming

    Science.gov (United States)

    Ramirez, Pedro; Dickerson, Kimberly K.; Lindstrom, Jim; Meteyer, Carol U.; Darrah, Scott

    2015-01-01

    Two hundred fifty-one Lapland longspur (Calcarius lapponicus) carcasses were recovered around an oil well drilling rig in Laramie County, Wyoming, USA, on December 13–14, 2010, apparent victims of a winter storm and “light entrapment” from the lights on the drilling rig during foggy conditions. We found Lapland longspur carcasses distributed around the drilling rig from 33 m to 171 m. Investigators did not find evidence of bird carcasses on the drilling rig deck or equipment immediately adjacent to the drilling rig. We ruled out chemical toxins and disease as a cause of mortality. Weather conditions, the circular depositional pattern of carcasses around the drilling rig, and bird necropsy results led investigators to conclude that the Lapland longspur mortality was the result of the migrating birds entering the area illuminated by the drilling rig lights in freezing fog and the birds repeatedly circling the drilling rig until they fell to the ground in exhaustion and dying from subsequent trauma. Further research is needed to understand how to most effectively adjust lighting of onshore drilling rigs to reduce the potential for avian light entrapment. Published 2014. This article is a U.S. Government work and is in the public domain in the USA.

  18. The development and testing of a fieldworthy system of improved fluid pumping device and liquid sensor for oil wells

    Energy Technology Data Exchange (ETDEWEB)

    Buckman, W.G.

    1991-12-31

    A major expenditure to maintain oil and gas leases is the support of pumpers, those individuals who maintain the pumping systems on wells to achieve optimum production. Many leases are marginal and are in remote areas and this requires considerable driving time for the pumper. The Air Pulse Oil Pump System is designed to be an economical system for the shallow stripper wells. To improve on the economics of this system, we have designed a Remote Oil Field Monitor and Controller to enable us to acquire data from the lease to our central office at anytime and to control the pumping activities from the central office by using a personal computer. The advent and economics of low-power microcontrollers have made it feasible to use this type of system for numerous remote control systems. We can also adapt this economical system to monitor and control the production of gas wells and/or pump jacks.

  19. Assessment of creation prospects of the effective economic stimulation mechanism of ecologically sustainable oil and gas complex development

    Directory of Open Access Journals (Sweden)

    Sheveleva Anastasia, V.

    2015-12-01

    Full Text Available Negative anthropogenous impact on environment is now felt especially sharply and gains global character that can lead to economic and ecological collapse, eventually. One of the most large-scale subjects of the economic environment doing harm to environment are the enterprises of an oil and gas complex as they in large volumes throw out the polluting substances and in high volumes take natural resources. However the field of activity of such enterprises is priority for national economy, and difficult interchangeability of energy raw material resources demands from the state and the oil and gas enterprises of development within realization of complete branch ecological-economic policy of the economic mechanism of stimulation of ecologically sustainable development of an oil and gas complex. Experience of last years within regulation and stimulation of decrease in pollution shows that the most effective way of achievement of it is implementation of serious capital investments in introduction of the environmentally friendly technologies in production allowing to receive a smaller stream of pollution "at the exit" a production system, and also a recycling of resources that can be provided by introduction in practice of work of the company of the best available technologies. Problems of ecologically sustainable development will also be answered by problems of economy not only in production and power, but also in power - a consumer sector for what it is necessary to provide compliance of the technologies used in extracting and processing the energy sectors, with technologies of economy of energy in a consumer sector. In the paper in this regard much attention is paid to possibility of formation of such economic mechanism via the public-private partnership mechanism that means that ecological-economic strategy of development of the enterprises of an oil and gas complex have to be coordinated with power strategy of development of regions and the

  20. Ionic interactions in the water zone at oil well-sites

    Energy Technology Data Exchange (ETDEWEB)

    Kleven, R.

    1996-11-01

    The aim of this doctoral thesis has been to obtain a better understanding of ionic behaviour in a water zone of sedimentary rock exposed to sea-water based drilling fluid and completion fluid. Interaction processes addressed have been ion exchange on the surface of the reservoir rocks and precipitation of divalent cations with sulphate ions from the sea water. Clay minerals are focused on because of their ability to conduct electricity through ion-exchange reactions. The most important parameters that the distribution of ions around a borehole depends upon are suggested to be (1) the ability of the sedimentary rocks to sorb/desorb ions, (2) the effect of added solutions on the sorption/desorption processes, (3) the mobility of ions. The first of four enclosed papers studies ionic interaction, mainly on homo-ionic clay mineral - salt solution, in batch experiments under pH, ionic strength and temperature conditions likely to occur in the field. Paper II investigates the use of tritiated water as a reference tracer in miscible displacement processes in porous sandstone cores. Ionic interaction processes during drilling of oil wells with conventional KCl bentonite mud tagged with HTO were studied by means of measured ionic and HTO concentration of water sampled in the near well-bore region. A tracer method was developed and ``tracer diagrams`` illustrate sorption/desorption processes. The water analyses, sampling procedure, and tracer techniques are presented in the third paper. Paper IV compares the interpretation of laboratory data and field data. 173 refs., 47 figs., 22 tabs.

  1. Development of Induction Logging Technology for Non-Stationary Conditions While Drilling Subhorozontal Sections of Oil and Gas Wells

    Directory of Open Access Journals (Sweden)

    V. K. Teplukhin

    2017-06-01

    Full Text Available The article presents the results of development of the induction logging module designed for resistivity measurements while drilling horizontal and directional wells for oil and gas. Materials of the tool testing during the drilling of wells in the oil field in the Republic of Bashkortostan are shown. We introduce the comparative analysis of resistivity data obtained after completion of the drilling, and the results obtained with developed complex as part of the LWD telemetry system TARGET during the drilling. The technical characteristics of complex MIR are presented.

  2. Isotope and chemical investigation of geothermal springs and thermal water produced by oil wells in potwat area, Pakistan

    International Nuclear Information System (INIS)

    Ahmad, M.; Rafique, M.; Tariq, J.A; Choudhry, M.A.; Hussain, Q.M.

    2008-10-01

    Isotopes and geochemical techniques were applied to investigate the origin, subsurface history and reservoir temperatures of geothermal springs in Potwar. Two sets of water samples were collected. Surface temperatures of geothermal springs ranges from 52 to 68.3 C. Waters produced by oil wells in Potwar area were also investigated. Geothermal springs of Potwar area are Na-HCO/sub 3/ type, while the waters produced by oil wells are Na-Cl and Ca-Cl types. Source of both the categories of water is meteoric water recharged from the outcrops of the formations in the Himalayan foothills. These waters undergo very high /sup 18/O-shift (up to 18%) due to rock-water interaction at higher temperatures. High salinity of the oil field waters is due to dissolution of marine evaporites. Reservoir temperatures of thermal springs determined by the Na-K geo thermometers are in the range of 56-91 deg. C, while Na-K-Ca, Na-K-Mg, Na-K-Ca-Mg and quartz geo thermometers give higher temperatures up to 177 C. Reservoir temperature determined by /sup 18/O(SO/Sub 4/-H/sub 2/O) geo thermometer ranges from 112 to 138 deg. C. There is wide variation in reservoir temperatures (54-297 deg. C) of oil fields estimated by different chemical geo thermometers. Na-K geo thermometer seems more reliable which gives close estimates to real temperature (about 100 deg. C) determined during drilling of oil wells. (author)

  3. Microbiological techniques for paraffin reduction in producing oil wells: Final report

    Energy Technology Data Exchange (ETDEWEB)

    Oppenheimer, C. H.; Hiebert, F. K.

    1989-04-01

    Alpha Environmental has completed an eighteen month field oriented, cooperative research program with the US Department of Energy to demonstrate a new economically viable process using petroleum degrading microorganisms, a biocatalyst, formation water and inorganic nutrients to recover residual oil from reservoirs. Alpha's mixed community of microorganisms decomposes crude oil to produce detergents, CO/sub 2/, and new cells, thus mechanically and chemically releasing oil from reservoir pores. The naturally-occurring bacteria utilized in this project were previously selected by screening and isolating microorganisms from soils contaminated with crude oil and petroleum products. The activity and level of salt tolerance (to 20% salinity) of the bacteria is enhanced by a biocatalyst, previously developed by Alpha Environmental. Field evidence suggests that the biocatalyst provides catalytic oxygen to the microorganisms in the reservoir, which augments low levels of in-situ molecular oxygen. 25 refs., 10 figs., 6 tabs.

  4. Assessment of technologies for the remediation of oil-contaminated soil resulting from exploded oil wells and burning oil fires in Kuwait

    International Nuclear Information System (INIS)

    Al-Awadhi, N.M.; Abdal, M.S.; Briskey, E.J.; Williamson, K.

    1992-01-01

    Large quantities of Kuwait desert soils have been contaminated by oil-lakes and by serial deposition of particulates and non-combusted petroleum products. The oil content of these soils must be reduced substantially in order to restore the potential of Kuwait's land for plant and animal production and to guard against long-term adverse implications to human health. Extensive world-wide research and development for the treatment of soils contaminated with hazardous wastes have results in a number of different types of technologies that might be used to remediate soils in Kuwait. These types of technologies, include incineration, thermal volatilization and steam leaching (oil recovery) and direct bioremediation, amongst others. The dimensions and technical aspects of the problem will be presented and applicable technology will be reviewed

  5. Limitation of the influx of formation water into oil wells. Ogranichenie pritoka plastovykh vod v neftyanye skvazhiny

    Energy Technology Data Exchange (ETDEWEB)

    Bulgakov, R.T.; Gazizov, A.Sh.; Gabdullin, R.G.; Yusupov, I.G.

    1976-01-01

    The problems of limiting the influx of water into oil wells are examined. On the basis of studies, systemization, and generalization of the reasons for the premature flooding of wells, the improvement of strata by polymer-cement solutions with consolidating liquid phases is considered. A detailed description is given of the technology and results of cementing well using solutions based on plugging cement and water-soluble phenol-formaldehyde resins of the TSD-9 type. Results are reported on the study of the properties of selective water-insulating substances based on acrylamide monomers and hydrolyzed polyacrylonitriles. Industrial testing of these materials is generalized. An economic evaluation is made of the efficiency of measures undertaken to prevent water influx into oil wells.

  6. Prediction of critical transport velocity for preventing sand deposition in gas-oil multiphase production and well systems

    Energy Technology Data Exchange (ETDEWEB)

    Bello, O.O.; Reinicke, K.M. [Technische Univ. Clausthal, Clausthal-Zellerfeld (Germany). Inst. of Petroleum Engineering; Teodoriu, C. [Texas A and M Univ., College Station, TX (United States). Dept. of Petroleum Engineering

    2008-10-23

    The critical transport velocity is one of the key parameters for gas-oil-sand multiphase production and well system design and safe operation. Existing American Petroleum Institute Recommended Practice 14E (API RP 14E) for the sizing of multiphase flow systems suggests an equation to calculate threshold transport velocity. This equation only considers mixture density and does not account for factors such as fluid properties, gas-liquid flow patterns, sand loading, sand particle size, size distributions, shape factor and density. This work presents an improved computational methodology, which can be applied to estimate the critical transport velocity required to ensure efficient performance of gas-oil-sand multiphase production and well systems. The improved method is based on the modelling of three-phase gas-oil-sand pipe flow physics from first principle. Computations of the critical transport velocities show reasonable agreement with values calculated from mechanistic model (Danielson, 2007) for a relatively wide range of design and operating conditions. Compared with the mechanistic model (Danielson, 2007), the present method has no imposed limitations to the range of applicability. It is also takes into adequate account the effects of operating pressure, flow geometry, sand particle size, size distribution and shape factor, which have considerable influence on the critical transport velocity in gas-oil-sand multiphase production and well systems. (orig.)

  7. Hydraulic Fracturing of 403 Shallow Diatomite Wells in South Belridge Oil Field, Kern County, California, in 2014

    Science.gov (United States)

    Wynne, D. B.; Agusiegbe, V.

    2015-12-01

    We examine all 403 Hydraulic Fracture (HF) jobs performed by Aera Energy, LLC, in the South Belridge oil field, Kern County, CA in 2014. HFs in the South Belridge oil field are atypical amongst North American plays because the reservoir is shallow and produced via vertical wells. Our data set constitutes 88% of all HF jobs performed in CA oil fields in calendar-2014. The South Belridge field produces 11% of California's oil and the shallow HFs performed here differ from most HFs performed elsewhere. We discuss fracture modeling and methods and summary statistics, and modelled dimensions of fractures and their relationships to depth and reservoir properties. The 403 HFs were made in the diatomite-dominated Reef Ridge member of the Monterey Formation. The HFs began at an average depth of 1047 feet below ground (ft TVD) and extended an average of 626 ft vertically downward. The deepest initiation of HF was at 2380 ft and the shallowest cessation was at 639 ft TVD. The average HF was performed using 1488 BBL (62,496 gallons) of water. The HFs were performed in no more than 6 stages and nearly all were completed within one day. We (1) compare metrics of the South Belridge sample group with recent, larger "all-CA" and nationwide samples; and (2) conclude that if relationships of reservoir properties, well completion and HF are well understood, shallow diatomite HF may be optimized to enhance production while minimizing environmental impact.

  8. Comparative risk assessment of spill response options for a deepwater oil well blowout: Part III. Stakeholder engagement.

    Science.gov (United States)

    Walker, Ann Hayward; Scholz, Debra; McPeek, Melinda; French-McCay, Deborah; Rowe, Jill; Bock, Michael; Robinson, Hilary; Wenning, Richard

    2018-05-25

    This paper describes oil spill stakeholder engagement in a recent comparative risk assessment (CRA) project that examined the tradeoffs associated with a hypothetical offshore well blowout in the Gulf of Mexico, with a specific focus on subsea dispersant injection (SSDI) at the wellhead. SSDI is a new technology deployed during the Deepwater Horizon (DWH) oil spill response. Oil spill stakeholders include decision makers, who will consider whether to integrate SSDI into future tradeoff decisions. This CRA considered the tradeoffs associated with three sets of response strategies: (1) no intervention; (2) mechanical recovery, in-situ burning, and surface dispersants; and, (3) SSDI in addition to responses in (2). For context, the paper begins with a historical review of U.S. policy and engagement with oil spill stakeholders regarding dispersants. Stakeholder activities throughout the project involved decision-maker representatives and their advisors to inform the approach and consider CRA utility in future oil spill preparedness. Copyright © 2018 Elsevier Ltd. All rights reserved.

  9. Inventory of orphan oil and natural gas wells in the Dover and Gautreau Village areas of Westmorland County, New Brunswick

    International Nuclear Information System (INIS)

    Brennan, J.

    1999-01-01

    In 1997, the Government of New Brunswick conducted an inventory of orphan wells in the vicinity of Dover and Gautreau Village in Westmorland County. The term orphan wells refers to those oil and natural gas wells which have been abandoned and have no owner. An abandoned well refers to those wells that are no longer active and have been properly plugged. A total of 19 orphan wells were discovered with the help of landowners and historical maps. These wells are believed to have dated from 1860 to 1906. The locations of the wells were determined digitally using the Global Positioning System. The environmental conditions around the orphan wells were evaluated and classified according to a proposed system used by the State of Michigan. The wells were separated into three categories based on the amount of petroleum contamination of soil and water. Water contamination was further divided into contamination of groundwater and surface water. 7 refs., 34 figs

  10. Characteristics and propierties of oil-well cements additioned with blast furnace slag

    Directory of Open Access Journals (Sweden)

    Sánchez, R.

    2011-06-01

    Full Text Available The present paper addresses the alkali activation of Portland cements containing blast furnace slag (20 and 30% of the cement by weight with a view to the possible use of these materials in oil well construction. The hydration studies conducted showed that in cement/slag blends, the sodium silicate activating solution partially inhibited the dissolution of the silicate phases in the Portland cement, retarding cement hydration and reducing the precipitation of reaction products. Due to such partial inhibition, the cement/slag blends had significantly lower mechanical strength than Portland cements hydrated with water. 29Si and 27Al MAS NMR and BSE/EDX studies, in turn, showed that the C-S-H gel forming in the alkali-activated cement/slag pastes contained Al in tetrahedral positions and low Ca/Si ratios.

    En el presente trabajo se ha estudiado la activación alcalina de cementos Pórtland con incorporación de escoria de horno alto (20% y 30% con respecto al peso de cemento para su posible aplicación en la construcción de pozos petrolíferos. Los estudios de hidratación realizados indican que en mezclas cemento/escoria, la disolución activadora de silicato sódico inhibe parcialmente la disolución de las fases silicato del cemento Pórtland originando un retraso de su hidratación así como la menor precipitación de productos de reacción. Dicha parcial inhibición de los procesos reactivos en las mezclas cemento/escoria originan resistencias mecánicas significativamente inferiores a las pastas de cemento Portland hidratadas con agua. Finalmente, los estudios de 29Si y 27Al RMN MAS y BSE/EDX indican que el gel C-S-H formado en pastas de mezcla cemento/escoria activadas alcalinamente presenta Al en posiciones tetraédricas y bajas relaciones Ca/Si.

  11. Amazing wells

    Energy Technology Data Exchange (ETDEWEB)

    Ross, E.; Leschart, M.; Mahoney, J.; Smith, M.

    2002-02-01

    Six wells and a drilling rig, setting company, national and world records such as deepest well, longest horizontal well, and record setting completion technology are described. Steam assisted gravity drainage (SAGD) is mainly responsible for these outstanding successes. Discovered more than 20 years ago by a then Imperial oil scientist (Dr. Roger Butler) SAGD promises recovery rates of about 70 per cent for the right reservoir; more than twice the 25 to 30 per cent recovery rate with cyclic stimulation at Cold Lake and an average recovery rate of about 28 per cent for all Alberta light, medium and heavy oil wells. The seven facilities discussed in this article are : (1) Alberta Energy Company's Forest Hill oil sands project near Cold Lake, the first commercial SAGD operation where well pairs are producing 1,200-1,500 bbls per day; (2) Talisman Energy's Lovett River wells, which hold the company's depth record for a horizontal well in the Alberta Foothills; (3) Also owned by Talisman Energy in the Buchan Field in the North Sea, this well is famous for the fact that it was drilled with coiled tubing from a floating production vessel; : (4) in the Peco Field, south of Edson Alberta and owned by EOG Resources Canada, this well holds the Canadian offshore record for a single run using rotary steerable technology; (5) Burlington Resources Canada 's Burlington HZ Hinton 2-34-52-26 W5M well is best known for its record setting extended reach open hole coiled tubing job; (6) another Burlington Resources well holds the record for the deepest one-trip whipstock system ever run in Canada and milled successfully in one trip; and (7) a drilling rig in the Wabasca-Brintnell area of northern Alberta, owned by Canadian Natural Resources Limited, holds the record for drilling the largest number of horizontal holes in one year with the same rig.

  12. MODELING OF FLOW AND TRANSPORT INDUCED BY PRODUCTION OF HYDROFRACTURE-STIMULATED GAS WELLS NEAR THE RULISON NUCLEAR TEST

    Energy Technology Data Exchange (ETDEWEB)

    Hodges, Rex A. [Navarro Research and Engineering; Cooper, Clay [Desert Research Inst. (DRI), Reno, NV (United States); Falta, Ronald [Clemson Univ., SC (United States)

    2012-09-17

    The Piceance Basin in western Colorado contains significant reserves of natural gas in poorly connected, low-permeability (tight) sandstone lenses of the Mesaverde Group. The ability to enhance the production of natural gas in this area has long been a goal of the oil and gas industry. The U.S. Atomic Energy Commission, a predecessor agency to the U.S. Department of Energy (DOE) and the U.S. Nuclear Regulatory Commission, participated in three tests using nuclear detonations to fracture tight formations in an effort to enhance gas production. The tests were conducted under Project Plowshare, a program designed to identify peaceful, beneficial uses for nuclear devices. The first, Project Gasbuggy, was conducted in 1967 in the San Juan Basin of New Mexico. The two subsequent tests, Project Rulison in 1969 and Project Rio Blanco in 1973, were in the Piceance Basin. The ability to enhance natural gas production from tight sands has become practical through advances in hydraulic fracturing technology (hydrofracturing). This technology has led to an increase in drilling activity near the Rulison site, raising concerns that contamination currently contained in the subsurface could be released through a gas well drilled too close to the site. As wells are drilled nearer the site, the DOE Office of Legacy Management has taken the approach outlined in the June 2010 Rulison Path Forward document (DOE 2010), which recommends a conservative, staged approach to gas development. Drillers are encouraged to drill wells in areas with a low likelihood of encountering contamination (both distance and direction from the detonation zone are factors) and to collect data from these wells prior to drilling nearer the site’s 40 acre institutional control boundary (Lot 11). Previous modeling results indicate that contamination has been contained within Lot 11 (Figure 1). The Path Forward document couples the model predictions with the monitoring of gas and produced water from the gas wells

  13. Proceedings of the 2002 Petroleum Society of CIM/SPE/CHOA International Thermal Operations and Heavy Oil Symposium, International Conference on Horizontal Well Technology, and Canadian Heavy Oil Association Business Conference : Resources 2 Reserves 2 Results. CD ROM ed.

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-07-01

    This three day conference combined the Petroleum Society's International Horizontal Well and Technology Conference, the Society of Petroleum Engineer's (SPE) International Thermal Operations and Heavy Oil Symposium, and the Canadian Heavy Oil Association's (CHOA) Annual Business Meeting. The 87 presentations covered all aspects of heavy oil, thermal, and horizontal well technology from geosciences and drilling to economics and environment. The themes included financing, turning projects into results, eliminating the downstream barriers to oil sand development in North America and the world, and emerging technologies for horizontal or heavy oil applications. The conference included the following 20 sessions: (1) thermal operations/engineering, (2) well testing/productivity of horizontal wells, (3) heavy oil operations, (4) environmental aspects of heavy oil projects, (5) upgrading/pipelines, (6) economics and project appraisal, (7) simulation studies of thermal projects, (8) multilaterals, (9) horizontal wells in conventional reservoirs, (10) cold production of heavy oil, (11) horizontal drilling in thermal projects, (12) simulation studies of horizontal wells, (13) horizontal drilling technology, (14) thermal field studies and horizontal wells in heavy oil, (15) completion/production technology of horizontal and thermal wells, (16) physics and PVT of heavy oil recovery processes, (17) reservoir characterization/geosciences, (18) horizontal injectors/produced water technology, (19) emerging technologies, and (20) reservoir geomechanics/fracturing. Tutorials were also organized to provide opportunity to review areas that have undergone major changes. A total of 73 papers were indexed separately for inclusion in the database. refs., tabs., figs.

  14. High performance nature of biodegradable polymeric nanocomposites for oil-well drilling fluids

    Directory of Open Access Journals (Sweden)

    Tarek M. Madkour

    2016-06-01

    Full Text Available Multi-walled carbon nanotube (MWCNT and graphene nanoplatelet reinforced thermoplastic poly(lactic acid (PLA biodegradable nanocomposites were designed and prepared using solution casting techniques. The prepared biodegradable polymers are expected to provide an environmentally friendly alternative to petroleum-based polymers. Both nanocomposite systems exhibited better thermal stability and improved mechanical performance over the unreinforced polymer exhibiting excellent strength and degradability. The addition of graphene nanofiller in varied amounts was aimed to enhance the thermal and mechanical properties of the nanocomposites even further and incorporate the outstanding characteristics of graphene nanoplatelets into the nanocomposites. The polymeric nanocomposites showed also superior advantages for oil drilling relevances, automotive lubricating purposes, membrane technology and food packaging. Scanning electron microscopy images indicated a homogeneous dispersion of the nanofiller within the polymeric matrix at low filler loadings and a cluster formation at higher loadings that could be responsible for the polymeric matrix movement restrictions. The enthalpy of mixing (the polymer and the nanofiller measured could explain the cause of the repulsive interactions between the nanoparticles and the polymeric chains, which created an additional excluded volume that the polymeric segments were restricted to occupy, thus forcing the conformational characteristics of the polymeric chains to deviate away from those of the bulk chains. The prepared polymeric nano composites (poly lactic acid carbon nano tube and poly lactic acid graphene nanoplatelets were utilized in the formulation of oil-base mud as a viscosifier. The rheological, filtration properties and electrical stability of the oil based mud formulation with the new polymeric nanocomposite were studied and the result compared to the oil-based mud formulation with commercial viscosifier.

  15. Methods for the control of fracgel degradation in oil and gas wells; Methoden zur Kontrolle der Fracgelzerstoerung in Oel- und Gasbohrungen

    Energy Technology Data Exchange (ETDEWEB)

    Wenzke, B.; Storz, J.; Clasen, C.; Kulicke, W.M. [Hamburg Univ. (Germany). Inst. fuer Technische und Makromolekulare Chemie

    2007-04-15

    Previous experience in face operation demonstrated that the use of fracgels often leads to an incomplete fracgel recovery and therefore to a decreased productivity of the stimulated well. It is assumed that insufficient degradation of the fracgel caused by poor activity of the breakers leads to a decrease in productivity. The aim of this work was the determination of effective breakers for the use in oil and gas wells to enhance the degradation of polymer fracgels. The investigations were carried out with Guar-based fracgels. These gels consisted of Guar or Hydroxypropyl-Guar both crosslinked with Borax (low temperature fracgels) as well as Zirconium-crosslinked Carboxymethyl-Hydroxypropyl-Guar (CMHPG; high temperature fracgel). The work covered polymer analytical investigations, comprehensive rheological investigations of fracgels i.e. variation of pH-value, temperature, electrolytes (Li{sup +}, Na{sup +}, K{sup +}) as well as degradation studies with different breakers. The decrease of the pH-value led to a total destruction of the low temperature fracgel network. The presence of electrolytes led to a rapid contraction of the gel forming a solid phase (syneresis). In degradation experiments, contracted Guar-Borax gels were successfully treated with acids, enzymes and high concentrated oxidative breakers at T=60 C. High temperature fracgels (CMHPG/Zirconium) were only partially degraded at increased temperatures with an oxidative breaker, whereas at T=150 C a complete thermal degradation was observed. (orig.)

  16. Nano-chemo-mechanical signature of conventional oil-well cement systems: Effects of elevated temperature and curing time

    Energy Technology Data Exchange (ETDEWEB)

    Krakowiak, Konrad J., E-mail: kjkrak@mit.edu [Civil and Environmental Engineering Department, Massachusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, MA 02139-4307 (United States); Thomas, Jeffrey J., E-mail: JThomas39@slb.com [Schlumberger-Doll Research Center, 1 Hampshire St., Cambridge, MA 02139-1578 (United States); Musso, Simone, E-mail: SMusso@slb.com [Schlumberger-Doll Research Center, 1 Hampshire St., Cambridge, MA 02139-1578 (United States); James, Simon, E-mail: james6@slb.com [Schlumberger Riboud Product Center, 1 rue Henri Becquerel, Clamart 92140 (France); Akono, Ange-Therese, E-mail: aakono@illinois.edu [Civil and Environmental Engineering Department, Massachusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, MA 02139-4307 (United States); Ulm, Franz-Josef, E-mail: ulm@mit.edu [Civil and Environmental Engineering Department, Massachusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, MA 02139-4307 (United States)

    2015-01-15

    With ever more challenging (T,p) environments for cementing applications in oil and gas wells, there is a need to identify the fundamental mechanisms of fracture resistant oil well cements. We report results from a multi-technique investigation of behavior and properties of API class G cement and silica-enriched cement systems subjected to hydrothermal curing from 30 °C to 200 °C; including electron probe microanalysis, X-ray diffraction, thermogravimetry analysis, electron microscopy, neutron scattering (SANS), and fracture scratch testing. The results provide a new insight into the link between system chemistry, micro-texture and micro-fracture toughness. We suggest that the strong correlation found between chemically modulated specific surface and fracture resistance can explain the drop in fracture properties of neat oil-well cements at elevated temperatures; the fracture property enhancement in silica-rich cement systems, between 110° and 175 °C; and the drop in fracture properties of such systems through prolonged curing over 1 year at 200 °C.

  17. Novel Downhole Electromagnetic Flowmeter for Oil-Water Two-Phase Flow in High-Water-Cut Oil-Producing Wells.

    Science.gov (United States)

    Wang, Yanjun; Li, Haoyu; Liu, Xingbin; Zhang, Yuhui; Xie, Ronghua; Huang, Chunhui; Hu, Jinhai; Deng, Gang

    2016-10-14

    First, the measuring principle, the weight function, and the magnetic field of the novel downhole inserted electromagnetic flowmeter (EMF) are described. Second, the basic design of the EMF is described. Third, the dynamic experiments of two EMFs in oil-water two-phase flow are carried out. The experimental errors are analyzed in detail. The experimental results show that the maximum absolute value of the full-scale errors is better than 5%, the total flowrate is 5-60 m³/d, and the water-cut is higher than 60%. The maximum absolute value of the full-scale errors is better than 7%, the total flowrate is 2-60 m³/d, and the water-cut is higher than 70%. Finally, onsite experiments in high-water-cut oil-producing wells are conducted, and the possible reasons for the errors in the onsite experiments are analyzed. It is found that the EMF can provide an effective technology for measuring downhole oil-water two-phase flow.

  18. Novel Downhole Electromagnetic Flowmeter for Oil-Water Two-Phase Flow in High-Water-Cut Oil-Producing Wells

    Directory of Open Access Journals (Sweden)

    Yanjun Wang

    2016-10-01

    Full Text Available First, the measuring principle, the weight function, and the magnetic field of the novel downhole inserted electromagnetic flowmeter (EMF are described. Second, the basic design of the EMF is described. Third, the dynamic experiments of two EMFs in oil-water two-phase flow are carried out. The experimental errors are analyzed in detail. The experimental results show that the maximum absolute value of the full-scale errors is better than 5%, the total flowrate is 5–60 m3/d, and the water-cut is higher than 60%. The maximum absolute value of the full-scale errors is better than 7%, the total flowrate is 2–60 m3/d, and the water-cut is higher than 70%. Finally, onsite experiments in high-water-cut oil-producing wells are conducted, and the possible reasons for the errors in the onsite experiments are analyzed. It is found that the EMF can provide an effective technology for measuring downhole oil-water two-phase flow.

  19. Two-fluid model for transient analysis of slug flow in oil wells

    International Nuclear Information System (INIS)

    Cazarez-Candia, O.; Benitez-Centeno, O.C.; Espinosa-Paredes, G.

    2011-01-01

    In this work it is presented a transient, one-dimensional, adiabatic model for slug flow simulation, which appears when liquid (mixture of oil and water) and gas flow simultaneously through pipes. The model is formed by space and time averaged conservation equations for mass, momentum and energy for each phase, the numerical solution is based on the finite difference technique in the implicit scheme. Velocity, pressure, volumetric fraction and temperature profiles for both phases were predicted for inclination angles from the horizontal to the vertical position (unified model) and ascendant flow. Predictions from the model were validated using field data and ten correlations commonly used in the oil industry. The effects of gas heating or cooling, due to compression and expansion processes, on the predictions and numerical stability, were studied. It was found that when these effects are taken into account, a good behavior of temperature predictions and numerical stability are obtained. The model presents deviations lower than 14% regarding field data and it presents better predictions than most of the correlations.

  20. Two-fluid model for transient analysis of slug flow in oil wells

    Energy Technology Data Exchange (ETDEWEB)

    Cazarez-Candia, O., E-mail: ocazarez@imp.mx [Instituto Mexicano del Petroleo, Eje central Lazaro Cardenas No. 152, Col. San Bartolo Atepehuacan, Mexico D.F. 07730 (Mexico); Instituto Tecnologico de Zacatepec, Depto. de Metal-Mecanica, Calzada Tecnologico, No. 27, Zacatepec, Morelos 62780 (Mexico); Benitez-Centeno, O.C. [Centro Nacional de Investigacion y Desarrollo Tecnologico, Depto. de Mecanica, Interior Internado Palmira s/n, Col. Palmira, Cuernavaca, Morelos 62490 (Mexico); Espinosa-Paredes, G. [Area de Ingenieria en Recursos Energeticos, Universidad Autonoma Metropolitana-Iztapalapa, Av San Rafael Atlixco No 186, Col. Vicentina 55-534, Mexico D.F. 09340 (Mexico)

    2011-06-15

    In this work it is presented a transient, one-dimensional, adiabatic model for slug flow simulation, which appears when liquid (mixture of oil and water) and gas flow simultaneously through pipes. The model is formed by space and time averaged conservation equations for mass, momentum and energy for each phase, the numerical solution is based on the finite difference technique in the implicit scheme. Velocity, pressure, volumetric fraction and temperature profiles for both phases were predicted for inclination angles from the horizontal to the vertical position (unified model) and ascendant flow. Predictions from the model were validated using field data and ten correlations commonly used in the oil industry. The effects of gas heating or cooling, due to compression and expansion processes, on the predictions and numerical stability, were studied. It was found that when these effects are taken into account, a good behavior of temperature predictions and numerical stability are obtained. The model presents deviations lower than 14% regarding field data and it presents better predictions than most of the correlations.

  1. A preliminary assessment of the radiological implications of commercial utilization of natural gas from a nuclearly stimulated well

    Energy Technology Data Exchange (ETDEWEB)

    Jacobs, D G; Struxness, E G [Health Physics Division, Oak Ridge National Laboratory, Oak Ridge, TN (United States); Bowman, C R [El Paso Natural Gas Company, El Paso, TX (United States)

    1970-05-01

    Widespread utilization of nuclear explosives, in conjunction with the natural gas industry, can result in radiation exposure of sizable population groups. It is prudent to make realistic assessments of such potential radiation exposures before they occur and, unless the expected exposures are clearly insignificant, to consider these exposures in evaluating the net benefit of this particular use of nuclear energy. All pertinent facts relating to such assessments should be made public and presented in such a way that those who are to assume the risks, if any, can make a reasonable judgment as to whether the risks are acceptable. Radioactivity in natural gas from the Gasbuggy cavity has been analyzed prior to and during flaring operations. None of this gas has entered the collection and distribution system, but a theoretical analysis has been made of the hypothetical impact on members of the public that would have occurred if the gas had been introduced into the commercial stream. Dose equivalents have been estimated for both workers and consumers. In this analysis, Gasbuggy gas has been traced through a real gas-collection system and processing plant, as represented by the present situation existing in the San Juan Production Division, El Paso Natural Gas Company. In addition, a number of considerations are presented which would apply to radiation exposure in metropolitan areas. Results of this analysis for the Gasbuggy well indicate hypothetical dose equivalents to various population groups to be well within the annual dose limits suggested by the International Commission on Radiological Protection. Projection to a steady-state situation involving extensive natural gas production from many producing wells also resulted in hypothetical dose equivalents within the annual dose limits. Simple extrapolation of the results from this analysis to potential exposures resulting from nuclear stimulation of other gas reservoirs cannot be made on a direct basis, but this method

  2. A preliminary assessment of the radiological implications of commercial utilization of natural gas from a nuclearly stimulated well

    International Nuclear Information System (INIS)

    Jacobs, D.G.; Struxness, E.G.; Bowman, C.R.

    1970-01-01

    Widespread utilization of nuclear explosives, in conjunction with the natural gas industry, can result in radiation exposure of sizable population groups. It is prudent to make realistic assessments of such potential radiation exposures before they occur and, unless the expected exposures are clearly insignificant, to consider these exposures in evaluating the net benefit of this particular use of nuclear energy. All pertinent facts relating to such assessments should be made public and presented in such a way that those who are to assume the risks, if any, can make a reasonable judgment as to whether the risks are acceptable. Radioactivity in natural gas from the Gasbuggy cavity has been analyzed prior to and during flaring operations. None of this gas has entered the collection and distribution system, but a theoretical analysis has been made of the hypothetical impact on members of the public that would have occurred if the gas had been introduced into the commercial stream. Dose equivalents have been estimated for both workers and consumers. In this analysis, Gasbuggy gas has been traced through a real gas-collection system and processing plant, as represented by the present situation existing in the San Juan Production Division, El Paso Natural Gas Company. In addition, a number of considerations are presented which would apply to radiation exposure in metropolitan areas. Results of this analysis for the Gasbuggy well indicate hypothetical dose equivalents to various population groups to be well within the annual dose limits suggested by the International Commission on Radiological Protection. Projection to a steady-state situation involving extensive natural gas production from many producing wells also resulted in hypothetical dose equivalents within the annual dose limits. Simple extrapolation of the results from this analysis to potential exposures resulting from nuclear stimulation of other gas reservoirs cannot be made on a direct basis, but this method

  3. Onset of surface stimulated emission at 260 nm from AlGaN multiple quantum wells

    KAUST Repository

    Li, Xiaohang

    2015-12-14

    We demonstrated onset of deep-ultraviolet (DUV) surface stimulated emission (SE) from c-plane AlGaNmultiple-quantum well(MQW)heterostructuresgrown on a sapphire substrate by optical pumping at room temperature. The onset of SE became observable at a pumping power density of 630 kW/cm2. Spectral deconvolution revealed superposition of a linearly amplified spontaneous emission peak at λ ∼ 257.0 nm with a full width at half maximum (FWHM) of ∼12 nm and a superlinearly amplified SE peak at λ ∼ 260 nm with a narrow FWHM of less than 2 nm. In particular, the wavelength of ∼260 nm is the shortest wavelength of surface SE from III-nitride MQWheterostructures to date. Atomic force microscopy and scanning transmission electron microscopy measurements were employed to investigate the material and structural quality of the AlGaNheterostructures, showing smooth surface and sharp layer interfaces. This study offers promising results for AlGaNheterostructuresgrown on sapphire substrates for the development of DUV vertical cavity surface emitting lasers(VCSELs).

  4. Onset of surface stimulated emission at 260 nm from AlGaN multiple quantum wells

    International Nuclear Information System (INIS)

    Li, Xiaohang; Xie, Hongen; Ponce, Fernando A.; Ryou, Jae-Hyun; Detchprohm, Theeradetch; Dupuis, Russell D.

    2015-01-01

    We demonstrated onset of deep-ultraviolet (DUV) surface stimulated emission (SE) from c-plane AlGaN multiple-quantum well (MQW) heterostructures grown on a sapphire substrate by optical pumping at room temperature. The onset of SE became observable at a pumping power density of 630 kW/cm 2 . Spectral deconvolution revealed superposition of a linearly amplified spontaneous emission peak at λ ∼ 257.0 nm with a full width at half maximum (FWHM) of ∼12 nm and a superlinearly amplified SE peak at λ ∼ 260 nm with a narrow FWHM of less than 2 nm. In particular, the wavelength of ∼260 nm is the shortest wavelength of surface SE from III-nitride MQW heterostructures to date. Atomic force microscopy and scanning transmission electron microscopy measurements were employed to investigate the material and structural quality of the AlGaN heterostructures, showing smooth surface and sharp layer interfaces. This study offers promising results for AlGaN heterostructures grown on sapphire substrates for the development of DUV vertical cavity surface emitting lasers (VCSELs)

  5. GPU-Based Computation of Formation Pressure for Multistage Hydraulically Fractured Horizontal Wells in Tight Oil and Gas Reservoirs

    Directory of Open Access Journals (Sweden)

    Rongwang Yin

    2018-01-01

    Full Text Available A mathematical model for multistage hydraulically fractured horizontal wells (MFHWs in tight oil and gas reservoirs was derived by considering the variations in the permeability and porosity of tight oil and gas reservoirs that depend on formation pressure and mixed fluid properties and introducing the pseudo-pressure; analytical solutions were presented using the Newman superposition principle. The CPU-GPU asynchronous computing model was designed based on the CUDA platform, and the analytic solution was decomposed into infinite summation and integral forms for parallel computation. Implementation of this algorithm on an Intel i5 4590 CPU and NVIDIA GT 730 GPU demonstrates that computation speed increased by almost 80 times, which meets the requirement for real-time calculation of the formation pressure of MFHWs.

  6. Robust technology and system for management of sucker rod pumping units in oil wells

    Science.gov (United States)

    Aliev, T. A.; Rzayev, A. H.; Guluyev, G. A.; Alizada, T. A.; Rzayeva, N. E.

    2018-01-01

    We propose a technology for calculating the robust, normalized correlation functions of the signal from the force sensor on the rod string attached to the hanger of the sucker rod pumping unit. The robust normalized correlation functions are used to form sets of informative attribute combinations, each of which corresponds to a technical condition of the sucker rod pumping unit. We demonstrate how these sets can be used to solve identification and management problems in the oil production process in real time using inexpensive controllers. The results obtained from using the system on real objects are also presented in this paper. It was determined that the energy saved and prolonged overhaul period substantially increased the cost-effectiveness.

  7. Heat-resistant agent used for control sand of steam huff and puff heavy oil well

    Science.gov (United States)

    Zhang, F. S.; Liu, G. L.; Lu, Y. J.; Xiong, X. C.; Ma, J. H.; Su, H. M.

    2018-01-01

    Heat-resistant agent containing hydroxymethyl group was synthesized from coal tar, which has similar structure with phenolic resin and could improve the heat resistance of phenolic resin sand control agent. The results showed that the heat resistance of the sand control agent was improved by adding 10% to 30% heat-resistant agent, after 280°C high temperature treatment for 7d, the compressive strength of consolidated core was increased to more than 5MPa. The compressive strength of consolidation core was not decreased after immersion in formation water, crude oil, acid or alkaline medium, which showed good resistance to medium immersion. The sand control agent had small core damage and the core permeability damage ratio of sand control agent consolidation was only 18.7%.

  8. 78 FR 48895 - Information Collection Activities: Oil and Gas Well-Workover Operations; Proposed Collection...

    Science.gov (United States)

    2013-08-12

    ... event of encountering H 2 S. Review well-workover diagrams and procedures to ensure the safety of well... chart details the individual components and respective hour burden estimates of this ICR. In calculating... during BOP and coiled tubing tests for well- workovers on a pressure chart or with a digital recorder...

  9. SAGD pilot project, wells MFB-772 (producer) / MFB-773 (injector), U1,3 MFB-53 reservoir, Bare Field. Orinoco oil belt. Venezuela

    Energy Technology Data Exchange (ETDEWEB)

    Mago, R.; Franco, L.; Armas, F.; Vasquez, R.; Rodriguez, J.; Gil, E. [PDVSA EandP (Venezuela)

    2011-07-01

    In heavy oil and extra heavy oil fields, steam assisted gravity drainage is a thermal recovery method used to reduce oil viscosity and thus increase oil recovery. For SAGD to be successfully applied in deep reservoirs, drilling and completion of the producer and injector wells are critical. Petroleos de Venezuela SA (PDVSA) is currently assessing the feasibility of SAGD in the Orinoco oil belt in Venezuela and this paper aims at presenting the methodology used to ensure optimal drilling and completion of the project. This method was divided in several stages: planning, drilling and completion of the producer, injector and then of the observer wells and cold information capture. It was found that the use of magnetic guidance tools, injection pipe pre-insulated and pressure and temperature sensors helps optimize the drilling and completion process. A methodology was presented to standardize operational procedures in the drilling and completion of SAGD projects in the Orinoco oil belt.

  10. Interactive optimization of biosurfactant production by Paenibacillus alvei ARN63 isolated from an Iranian oil well.

    Science.gov (United States)

    Najafi, A R; Rahimpour, M R; Jahanmiri, A H; Roostaazad, R; Arabian, D; Soleimani, M; Jamshidnejad, Z

    2011-01-01

    The potential of an indigenous bacterial strain isolated from an Iranian oil field for the production of biosurfactant was investigated in this study. After isolation, the bacterium was characterized to be Paenibacillus alvei by biochemical tests and 16S ribotyping. The biosurfactant, which was produced by this bacterium, was able to lower the surface tension of media to 35 mN/m. Accordingly, thin layer chromatography (TLC) and FT-IR has been carried out to determine compositional analysis of the produced biosurfactant. After all the tests related to characterization of the biosurfactant produced by the isolated bacterium, it was characterized as lipopeptide derivative. The combination of central composite rotatable design (CCRD) and response surface methodology (RSM) was exploited to optimize biosurfactant production. Therefore, variations of four impressive parameters, pH, temperature, glucose and salinity concentrations were selected for optimization of growth conditions. The empirical model developed through RSM in terms of effective operational factors mentioned above was found to be adequate to describe the biosurfactant production. A maximum reduction in surface tension was obtained under the optimal conditions of 13.03 g/l glucose concentration, 34.76 °C, 51.39 g/l total salt concentration and medium pH 6.89. Copyright © 2010 Elsevier B.V. All rights reserved.

  11. Mechanisms of mineral scaling in oil and geothermal wells studied in laboratory experiments by nuclear techniques

    International Nuclear Information System (INIS)

    Bjoernstad, T.; Stamatakis, E.

    2006-01-01

    Two independent nuclear methods have been developed and tested for studies of mineral scaling mechanisms and kinetics related to the oil and geothermal industry. The first is a gamma transmission method to measure mass increase with a 30 MBq source of 133 Ba. The other method applies radioactive tracers of one or more of the scaling components. CaCO 3 -precipitation has been used as an example here where the main tracer has been 47 Ca 2+ . While the transmission method is an indirect method, the latter is a direct method where the reactions of specific components may be studied. Both methods are on-line, continuous and non-destructive, and capable to study scaling of liquids with saturation ratios approaching the solubility product. A lower limit for detection of CaCO 3 with the transmission method in sand-packed columns with otherwise reasonable experimental parameters is estimated to be < 1 mg in a 1 cm section of the tube packed with silica sand while the lower limit of detection for the tracer method with reasonable experimental parameters is estimated to < 1 μg in the same tube section. (author)

  12. Analysis of Bacterial Diversity in Different Heavy Oil Wells of a Reservoir in South Oman with Alkaline pH

    Directory of Open Access Journals (Sweden)

    Biji Shibulal

    2018-01-01

    Full Text Available The identification of potential hydrocarbon utilizing bacteria is an essential requirement in microbial enhanced oil recovery (MEOR. Molecular approaches like proteomic and genomic characterization of the isolates are replacing the traditional method of identification with systemic classification. Genotypic profiling of the isolates includes fingerprint or pattern-based technique and sequence-based technique. Understanding community structure and dynamics is essential for studying diversity profiles and is challenging in the case of microbial analysis. The present study aims to understand the bacterial community composition from different heavy oil contaminated soil samples collected from geographically related oil well areas in Oman and to identify spore-forming hydrocarbon utilizing cultivable bacteria. V4 region of 16S rDNA gene was the target for Ion PGM™. A total of 825081 raw sequences were obtained from Ion torrent from all the 10 soil samples. The species richness and evenness were found to be moderate in all the samples with four main phyla, Firmicutes, Bacteroidetes, Proteobacteria, and Actinobacteria, the most abundant being Firmicutes. Bacillus sp. ubiquitously dominated in all samples followed by Paenibacillus, which was followed by Brevibacillus, Planococcus, and Flavobacterium. Principal Coordinate Analysis (PCoA and UPGMA dendrogram clustered the 10 soil samples into four main groups. Weighted UniFrac significance test determined that there was significant difference in the communities present in soil samples examined. It can be concluded that the microbial community was different in all the 10 soil samples with Bacillus and Paenibacillus sp. as predominating genus. The 16S rDNA sequencing of cultivable spore-forming bacteria identified the hydrocarbon utilizing bacteria as Bacillus and Paenibacillus sp. and the nucleotide sequences were submitted to NCBI GenBank under accession numbers KP119097–KP119115. Bacillus and

  13. Role of garlic oil and selenium as stimulators to some antioxidant defense system in irradiated male rats

    International Nuclear Information System (INIS)

    El-Gawish, M.A.; Abdel-Azeem, M.G.

    2002-01-01

    The increased level of lipid peroxide product; malondialdehyde (MDA) in various tissues of irradiated animals, may play a crucial role in damaging effects of exposure to ionizing radiation mediated by reactive free radicals generation. The protective efficiency of oral administration of garlic oil (500 mg/kg b.wt) three times weekly together with a single intraperitoneal injection of selenium (0.5 mg/kg b.wt) weekly for two weeks was examined on some antioxidant defense system as well as ultrastructural study in rats subjected to fractionated doses of gamma radiation up to a dose level of 6 Gy (1.5 Gy day after day). Exposure to gamma radiation induced a significant elevation in the level of malondialdehyde in plasma and liver and non-significant change was observed in superoxide dismutase activity (SOD). Also a significant increase was occurred in hepatic glutathione (GSH) content and glutathione peroxidase (GSHPx) activity. The pretreatment of irradiated rats with garlic oil and selenium caused a significant decrease in elevated level of MDA and a significant increase in the activity of SOD, GSHPx and GSH contents in both blood and liver. Concerning the ultrastructure studies, liver of irradiated rats showed abnormal shape of nucleus and nucleus membrane, swollen mitochondria with ruptured cristae, rupture of endoplasmic reticulum and vaculated cytoplasm, while intestine of irradiated rats exhibited deformed, shortened and abnormal structure of microvilli, accumulation of nuclear chromatin and dilatation of terminal web layer. In group of rats treated with garlic oil and selenium before exposure to gamma radiation, noticeable amelioration in ultrastructure changes of liver and intestine induced by irradiation was observed indicating a beneficial radioprotective role of both garlic oil and selenium

  14. Effects of well placement and intelligent completions on SAGD in a full-field thermal-numerical model for Athabasca oil sands

    Energy Technology Data Exchange (ETDEWEB)

    Akram, F. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[Schlumberger Canada Ltd., Calgary, AB (Canada)

    2008-10-15

    This paper described a simulation study conducted to compare traditional and targeted, or smart, steam assisted gravity drainage (SAGD) and cyclic steam stimulation (CSS) processes in ultra-heavy oil and bitumen reservoirs. Simulations were conducted using a Schlumberger Petrel and ECLIPSE thermal simulator. A reservoir model was used to determine steam requirements and production strategies in multiple well pairs. A fiscal model was used to evaluate SAGD project costs as well as to determine incremental costs for each completion strategy. Results of the study showed that while the efficient use of steam did not yield higher recovery rates, the expected value of the projects was improved. Process and operational controls were investigated. Strategies considered in the study included the smart completion strategy designed to target optimal steam injection areas and avoiding continuous zones of low permeability or shale barriers. Three completion designs were simulated and results were then run through the fiscal model in order to determine the financial impacts of the methods. Five year forecasts were generated for all completion designs. The smart design yielded a 5 per cent cost improvement over other designs, and yielded 442 MSTB less bitumen over the 5 year period. It was concluded that the smart design generated an incremental CAD $1.8 mm discounted cash flow at a capitalized cost of 10 per cent. 6 refs., 3 tabs., 11 figs.

  15. 78 FR 68079 - Information Collection Activities: Oil and Gas Well-Completion Operations; Submitted for Office...

    Science.gov (United States)

    2013-11-13

    ... view all related materials. We will post all comments. Email [email protected] : cheryl... personnel, property, and natural resources; (d) well- completion operations are conducted on well casings... hours. The following chart details the individual components and estimated hour burdens. In calculating...

  16. 17 CFR 229.1208 - (Item 1208) Oil and gas properties, wells, operations, and acreage.

    Science.gov (United States)

    2010-04-01

    ... properties, wells, operations, and acreage. 229.1208 Section 229.1208 Commodity and Securities Exchanges..., operations, and acreage. (a) Disclose, as of a reasonably current date or as of the end of the fiscal year... interests owned in gross wells or acres expressed as whole numbers and fractions of whole numbers. (3...

  17. Economic Recovery of Oil Trapped at Fan Margins Using High Angle Wells and Multiple Hydraulic Fractures

    Energy Technology Data Exchange (ETDEWEB)

    Mike L. Laue

    1997-05-30

    The distal fan margin in the northeast portion of the Yowlumne field contains significant reserves but is not economical to develop using vertical wells. Numerous interbedded shales and deteriorating rock properties limit producibility. In addition, extreme depths (13,000 ft) present a challenging environment for hydraulic fracturing and artificial lift. Lastly, a mature waterflood increases risk because of the uncertainty with size and location of flood fronts. This project attempts to demonstrate the effectiveness of exploiting the distal fan margin of this slope-basin clastic reservoir through the use of a high-angle well completed with multiple hydraulic-fracture treatments. The combination of a high-angle (or horizontal) well and hydraulic fracturing will allow greater pay exposure than can be achieved with conventional vertical wells while maintaining vertical communication between thin interbedded layers and the wellbore. The equivalent production rate and reserves of three vertical wells are anticipated at one-half to two-thirds the cost.

  18. Crumb waste tire rubber surface modification by plasma polymerization of ethanol and its application on oil-well cement

    Energy Technology Data Exchange (ETDEWEB)

    Xiaowei, Cheng [State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation, Southwest Petroleum University, Chengdu (China); School of Material Science and Engineering, Southwest Petroleum University, Chengdu (China); Sheng, Huang [State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation, Southwest Petroleum University, Chengdu (China); School of Oil and Natural Gas Engineering, Southwest Petroleum University, Chengdu (China); Xiaoyang, Guo, E-mail: guoxiaoyangswpi@126.com [State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation, Southwest Petroleum University, Chengdu (China); School of Oil and Natural Gas Engineering, Southwest Petroleum University, Chengdu (China); Wenhui, Duan, E-mail: wenhui.duan@monash.edu [Department of Civil Engineering, Monash University, Clayton, Melbourne 3800 (Australia)

    2017-07-01

    Highlights: • The crumb waste tire rubber (WTR) was modified by plasma polymerization of ethanol. • Hydrophilic groups were introduced onto WTR surface and improved its hydrophilia. • The functionalized crumb WTR was applied in oil-well cement. • The mechanical properties of modified oil-well cement were intensively enhanced. - Abstract: Crumb waste tire rubber (WTR) was pretreated by oxygen low temperature plasma (LTP) and modified by LTP polymerization process of ethanol monomer to improve the adhesion property with oil-well cement matrix and the mechanical properties of cement. The surface properties of modified crumb WTR and the mechanical properties and structures of modified oil-well cement were investigated by means of contact angle measurement, dispersion test, attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS), mechanics performance tests, permeability test and scanning electron microscopy (SEM). It was demonstrated that LTP treatment changed both the surface composition and roughness. The contact angle of pretreated crumb WTR dramatically fell from 122° to 34°, and sample with ethanol LPT polymer film decreased even further to 11°. The ATR-FTIR and XPS analysis results demonstrated that hydrophilic groups, such as –COOH, C–OH, and –CHO, were introduced on the WTR surface. The oxygen atomic percent increased from 8.11% to 14.50% and 24.83%. The mechanical properties, porosity and permeability of raw cement were compared to samples modified by untreated crumb WTR, pretreated crumb WTR and ethanol LTP polymerization treated crumb WTR. It was found that after 28 days, the compressive strength of the samples with the untreated crumb WTR decreased to 80% with respect to raw cement. The tensile strength and flexural strength also had a slight reduction compared with the raw cement. On the contrary, after 28 days, the tensile strength of cement modified by LTP polymerization

  19. Crumb waste tire rubber surface modification by plasma polymerization of ethanol and its application on oil-well cement

    International Nuclear Information System (INIS)

    Xiaowei, Cheng; Sheng, Huang; Xiaoyang, Guo; Wenhui, Duan

    2017-01-01

    Highlights: • The crumb waste tire rubber (WTR) was modified by plasma polymerization of ethanol. • Hydrophilic groups were introduced onto WTR surface and improved its hydrophilia. • The functionalized crumb WTR was applied in oil-well cement. • The mechanical properties of modified oil-well cement were intensively enhanced. - Abstract: Crumb waste tire rubber (WTR) was pretreated by oxygen low temperature plasma (LTP) and modified by LTP polymerization process of ethanol monomer to improve the adhesion property with oil-well cement matrix and the mechanical properties of cement. The surface properties of modified crumb WTR and the mechanical properties and structures of modified oil-well cement were investigated by means of contact angle measurement, dispersion test, attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS), mechanics performance tests, permeability test and scanning electron microscopy (SEM). It was demonstrated that LTP treatment changed both the surface composition and roughness. The contact angle of pretreated crumb WTR dramatically fell from 122° to 34°, and sample with ethanol LPT polymer film decreased even further to 11°. The ATR-FTIR and XPS analysis results demonstrated that hydrophilic groups, such as –COOH, C–OH, and –CHO, were introduced on the WTR surface. The oxygen atomic percent increased from 8.11% to 14.50% and 24.83%. The mechanical properties, porosity and permeability of raw cement were compared to samples modified by untreated crumb WTR, pretreated crumb WTR and ethanol LTP polymerization treated crumb WTR. It was found that after 28 days, the compressive strength of the samples with the untreated crumb WTR decreased to 80% with respect to raw cement. The tensile strength and flexural strength also had a slight reduction compared with the raw cement. On the contrary, after 28 days, the tensile strength of cement modified by LTP polymerization

  20. Study of waste generation in the drilling and cementing operations during construction of offshore oil and gas wells

    Directory of Open Access Journals (Sweden)

    Letícia Ferraço de Campos

    2016-12-01

    Full Text Available This literature review aims to present drilling and cementing activities which take place during the construction of offshore oil and gas wells, listing the waste generated in each step. IBAMA, the environmental agency that regulates the activity, allows two disposal options for these wastes: disposal in open sea or treatment followed by disposal on shore. The documentary research applied in this article details the destination options showing that the monitoring required by the environmental agency is a way to track the actual results of the activities described.

  1. Limited output transcranial electrical stimulation (LOTES-2017): Engineering principles, regulatory statutes, and industry standards for wellness, over-the-counter, or prescription devices with low risk.

    Science.gov (United States)

    Bikson, Marom; Paneri, Bhaskar; Mourdoukoutas, Andoni; Esmaeilpour, Zeinab; Badran, Bashar W; Azzam, Robin; Adair, Devin; Datta, Abhishek; Fang, Xiao Hui; Wingeier, Brett; Chao, Daniel; Alonso-Alonso, Miguel; Lee, Kiwon; Knotkova, Helena; Woods, Adam J; Hagedorn, David; Jeffery, Doug; Giordano, James; Tyler, William J

    We present device standards for low-power non-invasive electrical brain stimulation devices classified as limited output transcranial electrical stimulation (tES). Emerging applications of limited output tES to modulate brain function span techniques to stimulate brain or nerve structures, including transcranial direct current stimulation (tDCS), transcranial alternating current stimulation (tACS), and transcranial pulsed current stimulation (tPCS), have engendered discussion on how access to technology should be regulated. In regards to legal regulations and manufacturing standards for comparable technologies, a comprehensive framework already exists, including quality systems (QS), risk management, and (inter)national electrotechnical standards (IEC). In Part 1, relevant statutes are described for medical and wellness application. While agencies overseeing medical devices have broad jurisdiction, enforcement typically focuses on those devices with medical claims or posing significant risk. Consumer protections regarding responsible marketing and manufacture apply regardless. In Part 2 of this paper, we classify the electrical output performance of devices cleared by the United States Food and Drug Administration (FDA) including over-the-counter (OTC) and prescription electrostimulation devices, devices available for therapeutic or cosmetic purposes, and devices indicated for stimulation of the body or head. Examples include iontophoresis devices, powered muscle stimulators (PMS), cranial electrotherapy stimulation (CES), and transcutaneous electrical nerve stimulation (TENS) devices. Spanning over 13 FDA product codes, more than 1200 electrical stimulators have been cleared for marketing since 1977. The output characteristics of conventional tDCS, tACS, and tPCS techniques are well below those of most FDA cleared devices, including devices that are available OTC and those intended for stimulation on the head. This engineering analysis demonstrates that with

  2. Towards a Quantitative Framework for Evaluating Vulnerability of Drinking Water Wells to Contamination from Unconventional Oil & Gas Development

    Science.gov (United States)

    Soriano, M., Jr.; Deziel, N. C.; Saiers, J. E.

    2017-12-01

    The rapid expansion of unconventional oil and gas (UO&G) production, made possible by advances in hydraulic fracturing (fracking), has triggered concerns over risks this extraction poses to water resources and public health. Concerns are particularly acute within communities that host UO&G development and rely heavily on shallow aquifers as sources of drinking water. This research aims to develop a quantitative framework to evaluate the vulnerability of drinking water wells to contamination from UO&G activities. The concept of well vulnerability is explored through application of backwards travel time probability modeling to estimate the likelihood that capture zones of drinking water wells circumscribe source locations of UO&G contamination. Sources of UO&G contamination considered in this analysis include gas well pads and documented sites of UO&G wastewater and chemical spills. The modeling approach is illustrated for a portion of Susquehanna County, Pennsylvania, where more than one thousand shale gas wells have been completed since 2005. Data from a network of eight multi-level groundwater monitoring wells installed in the study site in 2015 are used to evaluate the model. The well vulnerability concept is proposed as a physically based quantitative tool for policy-makers dealing with the management of contamination risks of drinking water wells. In particular, the model can be used to identify adequate setback distances of UO&G activities from drinking water wells and other critical receptors.

  3. Ten minutes of 1 mA transcranial direct current stimulation was well tolerated by children and adolescents: Self-reports and resting state EEG analysis.

    Science.gov (United States)

    Moliadze, Vera; Andreas, Saskia; Lyzhko, Ekaterina; Schmanke, Till; Gurashvili, Tea; Freitag, Christine M; Siniatchkin, Michael

    2015-10-01

    Transcranial direct current stimulation (tDCS) is a promising and well-tolerated method of non-invasive brain stimulation, by which cortical excitability can be modulated. However, the effects of tDCS on the developing brain are still unknown, and knowledge about its tolerability in children and adolescents is still lacking. Safety and tolerability of tDCS was assessed in children and adolescents by self-reports and spectral characteristics of electroencephalogram (EEG) recordings. Nineteen typically developing children and adolescents aged 11-16 years participated in the study. Anodal and cathodal tDCS as well as sham stimulation were applied for a duration of 10 min over the left primary motor cortex (M1), each with an intensity of 1 mA. Subjects were unable to identify whether they had received active or sham stimulation, and all participants tolerated the stimulation well with a low rate of adverse events in both groups and no serious adverse events. No pathological oscillations, in particular, no markers of epileptiform activity after 1mA tDCS were detected in any of the EEG analyses. In summary, our study demonstrates that tDCS with 1mA intensity over 10 min is well tolerated, and thus may be used as an experimental and treatment method in the pediatric population. Copyright © 2015 Elsevier Inc. All rights reserved.

  4. Differential effects of safflower oil versus fish oil feeding on insulin-stimulated glycogen synthesis, glycolysis, and pyruvate dehydrogenase flux in skeletal muscle: a 13C nuclear magnetic resonance study.

    Science.gov (United States)

    Jucker, B M; Cline, G W; Barucci, N; Shulman, G I

    1999-01-01

    To examine the effects of safflower oil versus fish oil feeding on in vivo intramuscular glucose metabolism and relative pyruvate dehydrogenase (PDH) versus tricarboxylic acid (TCA) cycle flux, rats were pair-fed on diets consisting of 1) 59% safflower oil, 2) 59% menhaden fish oil, or 3) 59% carbohydrate (control) in calories. Rates of glycolysis and glycogen synthesis were assessed by monitoring [1-(13)C]glucose label incorporation into [1-(13)C]glycogen, [3-(13)C]lactate, and [3-(13)C]alanine in the hindlimb of awake rats via 13C nuclear magnetic resonance (NMR) spectroscopy during a euglycemic (approximately 6 mmol/l) hyperinsulinemic (approximately 180 microU/ml) clamp. A steady-state isotopic analysis of lactate, alanine, and glutamate was used to determine the relative PDH versus TCA cycle flux present in muscle under these conditions. The safflower oil-fed rats were insulin resistant compared with control and fish oil-fed rats, as reflected by a markedly reduced glucose infusion rate (Ginf) during the clamp (21.4 +/- 2.3 vs. 31.6 +/- 2.8 and 31.7 +/- 1.9 mg x kg(-1) x min(-1) in safflower oil versus control and fish oil groups, respectively, P safflower oil group was associated with a lower rate of glycolysis (21.7 +/- 2.2 nmol x g(-1) x min(-1)) versus control (62.1 +/- 10.3 nmol x g(-1) x min(-1), P safflower oil, fish oil, and control, respectively) was detected. The intramuscular triglyceride (TG) content was increased in the safflower oil group (7.3 +/- 0.8 micromol/g) compared with the control group (5.2 +/- 0.8 micromol/g, P safflower oil (43 +/- 8%) versus the control (73 +/- 8%, P safflower oil feeding was a consequence of reduced glycolytic flux associated with an increase in relative free fatty acid/ketone oxidation versus TCA cycle flux, whereas fish oil feeding did not alter glucose metabolism and may in part be protective of insulin-stimulated glucose disposal by limiting intramuscular TG deposition.

  5. A Semi-Analytical Methodology for Multiwell Productivity Index of Well-Industry-Production-Scheme in Tight Oil Reservoirs

    Directory of Open Access Journals (Sweden)

    Guangfeng Liu

    2018-04-01

    Full Text Available Recently, the well-industry-production-scheme (WIPS has attracted more and more attention to improve tight oil recovery. However, multi-well pressure interference (MWPI induced by well-industry-production-scheme (WIPS strongly challenges the traditional transient pressure analysis methods, which focus on single multi-fractured horizontal wells (SMFHWs without MWPI. Therefore, a semi-analytical methodology for multiwell productivity index (MPI was proposed to study well performance of WIPS scheme in tight reservoir. To facilitate methodology development, the conceptual models of tight formation and WIPS scheme were firstly described. Secondly, seepage models of tight reservoir and hydraulic fractures (HFs were sequentially established and then dynamically coupled. Numerical simulation was utilized to validate our model. Finally, identification of flow regimes and sensitivity analysis were conducted. Our results showed that there was good agreement between our proposed model and numerical simulation; moreover, our approach also gave promising calculation speed over numerical simulation. Some expected flow regimes were significantly distorted due to WIPS. The slope of type curves which characterize the linear or bi-linear flow regime is bigger than 0.5 or 0.25. The horizontal line which characterize radial flow regime is also bigger 0.5. The smaller the oil rate, the more severely flow regimes were distorted. Well rate mainly determines the distortion of MPI curves, while fracture length, well spacing, fracture spacing mainly determine when the distortion of the MPI curves occurs. The bigger the well rate, the more severely the MPI curves are distorted. While as the well spacing decreases, fracture length increases, fracture spacing increases, occurrence of MWPI become earlier. Stress sensitivity coefficient mainly affects the MPI at the formation pseudo-radial flow stage, almost has no influence on the occurrence of MWPI. This work gains some

  6. Long wavelength stimulated emission up to 9.5 μm from HgCdTe quantum well heterostructures

    Energy Technology Data Exchange (ETDEWEB)

    Morozov, S. V.; Rumyantsev, V. V., E-mail: rumyantsev@ipmras.ru; Dubinov, A. A.; Kudryavtsev, K. E.; Antonov, A. V.; Gavrilenko, V. I. [Institute for Physics of Microstructures of Russian Academy of Sciences, 603950 Nizhny Novgorod (Russian Federation); Lobachevsky State University of Nizhny Novgorod, 603950 Nizhny Novgorod (Russian Federation); Kadykov, A. M. [Institute for Physics of Microstructures of Russian Academy of Sciences, 603950 Nizhny Novgorod (Russian Federation); UMR CNRS 5221, GIS-TERALAB, Université Montpellier II, 34095 Montpellier (France); Mikhailov, N. N. [A.V. Rzhanov Institute of Semiconductor Physics, Siberian Branch of Russian Academy of Sciences, 630090 Novosibirsk (Russian Federation); Novosibirsk State University, 630090 Novosibirsk (Russian Federation); Dvoretskii, S. A. [A.V. Rzhanov Institute of Semiconductor Physics, Siberian Branch of Russian Academy of Sciences, 630090 Novosibirsk (Russian Federation)

    2016-02-29

    Stimulated emission from waveguide HgCdTe structures with several quantum wells inside waveguide core is demonstrated at wavelengths up to 9.5 μm. Photoluminescence line narrowing down to kT energy, as well as superlinear rise in its intensity evidence the onset of the stimulated emission, which takes place under optical pumping with intensity as small as ∼0.1 kW/cm{sup 2} at 18 K and 1 kW/cm{sup 2} at 80 K. One can conclude that HgCdTe structures potential for long-wavelength lasers is not exhausted.

  7. 78 FR 48893 - Information Collection Activities: Oil and Gas Well-Completion Operations; Proposed Collection...

    Science.gov (United States)

    2013-08-12

    ... comments and view all related materials. We will post all comments. Email [email protected] . Mail or... correct and provides adequate protection for personnel, property, and natural resources; (d) well... reporting burden for this collection is 46,859 hours. The following chart details the individual components...

  8. Evaluation of cement thixotropy for the cement of oil wells in areas ...

    African Journals Online (AJOL)

    ... economical for cementing job operations in wells with loss zones. The results also show that the effect of LHF is positive, since in addition to his contribution to long term performances, especially the durability of hardened concrete, it improves the thixotropy of cement made of plaster. Keywords: cementing; lost circulation; ...

  9. Health and wellness trends in the oil and gas sector : insights from the Shepell-fgi Research Group

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2009-07-01

    This report discussed health and wellness trends in the oil and gas sector in relation to employee assistance program (EAP) data. The data were derived from oil and gas client organizations across Canada for 2008, and represented a population base of 14,685 employees. The data demonstrated that EAP utilization in the petroleum industry increased by approximately 5 per cent from 2006 to 2008. The sector's utilization was 34 per cent higher than the Canadian norm in 2006, and 40 per cent higher than in 2007 and 2008. Females used the EAP to a greater extent than males. A higher proportion of the spouses of workers accessed EAP than the national norm. Employees accessed EAP for assistance with work-life issues; family support services; and substance abuse interventions. Weight management and dietary consultations in relation to disease control were also of concern within the sector. A 66 per cent increase in childcare issues was noted, as well as a 148 per cent increase in eldercare issues, and a 112 per cent increase in addiction issues. The findings indicated that the EAP is being effectively communicated as a relevant and accessible tool. As the industry continues to develop in remote regions, new services and resources will be required to retain existing workforces and attract new employees. Prevention-focused training and services and program for at-risk groups are needed to ensure that employee health and productivity is maintained. 1 tab., 4 figs.

  10. A new experimental method to prevent paraffin - wax formation on the crude oil wells: A field case study in Libya

    Directory of Open Access Journals (Sweden)

    Elhaddad Elnori E.

    2015-01-01

    Full Text Available Wax formation and deposition is one of the most common problems in oil producing wells. This problem occurs as a result of the reduction of the produced fluid temperature below the wax appearance temperature (range between 46°C and 50°C and the pour point temperature (range between 42°C and 44°C. In this study, two new methods for preventing wax formation were implemented on three oil wells in Libya, where the surface temperature is, normally, 29°C. In the first method, the gas was injected at a pressure of 83.3 bar and a temperature of 65°C (greater than the pour point temperature during the gas-lift operation. In the second method, wax inhibitors (Trichloroethylene-xylene (TEX, Ethylene copolymers, and Comb polymers were injected down the casings together with the gas. Field observations confirmed that by applying these techniques, the production string was kept clean and no wax was formed. The obtained results show that the wax formation could be prevented by both methods.

  11. Investigation of prospects for forecasting non-linear time series by example of drilling oil and gas wells

    Science.gov (United States)

    Vlasenko, A. V.; Sizonenko, A. B.; Zhdanov, A. A.

    2018-05-01

    Discrete time series or mappings are proposed for describing the dynamics of a nonlinear system. The article considers the problems of forecasting the dynamics of the system from the time series generated by it. In particular, the commercial rate of drilling oil and gas wells can be considered as a series where each next value depends on the previous one. The main parameter here is the technical drilling speed. With the aim of eliminating the measurement error and presenting the commercial speed of the object to the current with a good accuracy, future or any of the elapsed time points, the use of the Kalman filter is suggested. For the transition from a deterministic model to a probabilistic one, the use of ensemble modeling is suggested. Ensemble systems can provide a wide range of visual output, which helps the user to evaluate the measure of confidence in the model. In particular, the availability of information on the estimated calendar duration of the construction of oil and gas wells will allow drilling companies to optimize production planning by rationalizing the approach to loading drilling rigs, which ultimately leads to maximization of profit and an increase of their competitiveness.

  12. Interactive Book Reading in Early Education: A Tool to Stimulate Print Knowledge as Well as Oral Language

    Science.gov (United States)

    Mol, Suzanne E.; Bus, Adriana G.; de Jong, Maria T.

    2009-01-01

    This meta-analysis examines to what extent interactive storybook reading stimulates two pillars of learning to read: vocabulary and print knowledge. The authors quantitatively reviewed 31 (quasi) experiments (n = 2,049 children) in which educators were trained to encourage children to be actively involved before, during, and after joint book…

  13. EPR and EOM studies in well samples from some Venezuelan oil fields: correlation with magnetic authigenesis

    International Nuclear Information System (INIS)

    Diaz, M.; Aldana, M.; Sequera, P.; Costanzo A, V.; Jimenez, S.M.

    2006-01-01

    Electron paramagnetic resonance (EPR), magnetic susceptibility (MS) and extractable organic matter (EOM) measurements were carried out in drilling fines, from near-surface levels, from producer and non-producer wells, with the purpose of examining a possible causal relationship between magnetic contrasts and underlying hydrocarbons. Organic matter free radical concentration (OMFRC) and EOM anomalies were found only at the producer wells, in the same zone where MS anomalies were observed. The EOM anomalies coincide in depth with the MS ones, while the OMFRC anomalies lie close to them. The results could be explained if a net transfer of electrons from reduced organic matter, possible induced by the underlying reservoir, to Fe(lII) (e.g. hematite) occurs. This process alters the original organic matter and produces the formation of EOM and Fe(ll) magnetic minerals (e.g. magnetite), with both anomalies coexisting. (Author)

  14. Topical viscosity control for light hydrocarbon displacing fluids in petroleum recovery and in fracturing fluids for well stimulation

    Science.gov (United States)

    Heller, John P.; Dandge, Dileep K.

    1986-01-01

    Solvent-type flooding fluids comprising light hydrocarbons in the range of ethane to hexane (and mixtures thereof) are used to displace crude oil in formations having temperatures of about 20 degrees to about 150 degrees Centigrade and pressures above about 650 psi, the light hydrocarbons having dissolved therein from about 0.05% to about 3% of an organotin compound of the formula R.sub.3 SnF where each R is independently an alkyl, aryl or alkyaryl group from 3 to 12 carbon atoms. Under the pressures and temperatures described, the organotin compounds become pentacoordinated and linked through the electronegative bridges, forming polymers within the light hydrocarbon flooding media to render them highly viscous. Under ambient conditions, the viscosity control agents will not readily be produced from the formation with either crude oil or water, since they are insoluble in the former and only sparingly soluble in the latter.

  15. Well selection in depleted oil and gas fields for a safe CO2 storage practice: A case study from Malaysia

    Directory of Open Access Journals (Sweden)

    Arshad Raza

    2017-03-01

    Full Text Available Carbon capture and sequestration technology is recognized as a successful approach taken to mitigate the amount of greenhouse gases released into the atmosphere. However, having a successful storage practice requires wise selection of suitable wells in depleted oil or gas fields to reduce the risk of leakage and contamination of subsurface resources. The aim of this paper is to present a guideline which can be followed to provide a better understanding of sophisticated wells chosen for injection and storage practices. Reviewing recent studies carried out on different aspects of geosequestration indicated that the fracture pressure of seals and borehole conditions such as cement-sheath integrity, distance from faults and fractures together with the depth of wells are important parameters, which should be part of the analysis for well selection in depleted reservoirs. A workflow was then designed covering these aspects and it was applied to a depleted gas field in Malaysia. The results obtained indicated that Well B in the field may have the potential of being a suitable conduit for injection. Although more studies are required to consider other aspects of well selections, it is recommended to employ the formation integrity analysis as part of the caprock assessment before making any decisions.

  16. Model for determining the completion and production policy in oil wells

    Energy Technology Data Exchange (ETDEWEB)

    Acurero S, L A

    1983-12-01

    An optimization scheme for reservoir development was examined considering the value of the resource, choice of completion and production techniques, and boundary conditions for the reservoir. A 3-phase semi-analytic single-well model was formulated to determine the reservoir response for any completion and production policy. Second, an optimization scheme based on the discrete version of the maximum principle of Pontryagin and the Fibonacci search method was formulated to determine the optimal production and completion policy. Both models are combined in a general algorithm of solution proposed to solve the optimization problem, and a computer code was developed and tested.

  17. Barium and sodium in sunflower plants cultivated in soil treated with wastes of drilling of oil well

    Directory of Open Access Journals (Sweden)

    Jésus Sampaio Junior

    2015-11-01

    Full Text Available ABSTRACTThis study aimed to evaluate the effects of the application of two types of oil drilling wastes on the development and absorption of barium (Ba and sodium (Na by sunflower plants. The waste materials were generated during the drilling of the 7-MGP-98D-BA oil well, located in the state of Bahia, Brazil. The treatments consisted of: Control – without Ba application, comprising only its natural levels in the soil; Corrected control – with fertilization and without wastes; and the Ba doses of 300, 3000 and 6000 mg kg-1, which were equivalent to the applications of 16.6, 165.9 and 331.8 Mg ha-1 of waste from the dryer, and 2.6, 25.7 and 51.3 Mg ha-1 of waste from the centrifugal. Plants cultivated using the first dose of dryer waste and the second dose of centrifugal waste showed growth and dry matter accumulation equal to those of plants under ideal conditions of cultivation (corrected control. The highest doses of dryer and centrifugal wastes affected the development of the plants. The absorption of Ba by sunflower plants was not affected by the increase in the doses. Na proved to be the most critical element present in the residues, interfering with sunflower development.

  18. Ultra high-temperature solids-free insulating packer fluid for oil and gas production, steam injection and geothermal wells

    Energy Technology Data Exchange (ETDEWEB)

    Ezell, R.G.; Harrison, D.J. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[Halliburton Energy Services, Calgary, AB (Canada)

    2008-10-15

    Uncontrolled heat transfer from production/injection tubing during thermal oil recovery via steam injection can be detrimental to the integrity of the casing and to the quality of the steam that is injected into the reservoir. An aqueous-based insulating packer fluid (IPF) was introduced to improve the steam injection process by controlling the total heat loss from the produced fluids to the surrounding wellbore, internal annuli and formation. The IPF was developed for elevated temperature environments through extensive investigation across multidisciplinary technology. The innovative system delivers performance beyond conventional systems of comparable thermal conductivity. Its density range and conductivity measurements were presented in this paper. High-temperature static aging tests showed superior gel integrity without any phase separation after exposure to temperatures higher than 260 degrees C. The new fluids are hydrate inhibitive, non-corrosive and pass oil and grease testing. They are considered to be environmentally sound by Gulf of Mexico standards. It was concluded that the new ultra high-performance insulating packer fluid (HTIPF) reduced the heat loss significantly by both conduction and convection. Heat transfer within the aqueous-based HTIPF was 97 per cent less than that of pure water. It was concluded that the HTIPF can be substituted for conventional packer fluids without compromising any well control issues. 21 refs., 1 tab., 4 figs.

  19. Hypermetabolic Conversion of Plant Oil into Water: Endothermic Biochemical Process Stimulated by Juvenile Hormone in the European Firebug, L.

    Directory of Open Access Journals (Sweden)

    Karel Sláma

    2016-01-01

    Full Text Available The physiological and biochemical mechanisms that enable insects to feed on dry food to secure enough water for larval growth were investigated. The study was carried out with a plethora of physiological methods, ranging from the simple volumetric determination of O 2 consumption and water intake to more advanced methods such as scanning microrespirography and thermovision imaging of insect's body temperature. The experiments were done on the European firebug, Pyrrhocoris apterus , which feeds exclusively on dry linden seeds. In order to survive, it needs to drink water or suck a sap from plants occasionally. It was found that the young larval instars compensate the occasional water deficiency by the increased production of metabolic water. The juvenile hormone (JH-dependent production of metabolic water, which was previously found in other species consuming dry food, was achieved in P. apterus by total metabolic combustion of the dietary lipid (neutral seed oil. The water-producing, hypermetabolic larvae were heated from inside by endothermic energy released from the uncoupling of oxidation from oxidative phosphorylation. The “warm”, hypermetabolic larvae burning the dietary oil into CO 2 and water showed the increased rates of respiratory metabolism. Microrespirographic recording of these larvae revealed the ratio of the respiratory quotient (RQ, CO 2 /O 2 of 0.7, which indicated the breakdown of a pure triglyceride. The warm hypermetabolic larvae could be easily spotted and distinguished from the “cold” larvae on the screen of a thermovision camera. The last instar larvae lacking the JH were always only cold. They metabolized a carbohydrate substrate exclusively (RQ = 1.0, while the dietary lipid was stored in the fat body. In comparison with the hypermetabolic larvae of some other species fed on dry food, which exhibited the highest rates of O 2 consumption ever recorded in a living organism (10–20 mL O 2 /g per hour, the metabolic

  20. Parametric analysis applied to perforating procedures of oil wells; Analise parametrica aplicada a procedimentos de canhoneio de pocos de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Baioco, Juliana Souza; Seckler, Carolina dos Santos; Silva, Karinna Freitas da; Jacob, Breno Pinheiro [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-Graduacao de Engenharia. Lab. de Metodos Computacionais e Sistemas Offshore; Silvestre, Jose Roberto; Soares, Antonio Claudio; Freitas, Sergio Murilo Santos [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Centro de Pesquisas

    2008-07-01

    The perforation process is an important in well construction. It provides contact between the reservoir rock and the well, allowing oil production. The procedure consists in using explosive charges to bore a hole into the casing and the rock, so that the reservoir fluid can flow to the well. Therefore, the right choice of both the gun and the charge type is extremely important, knowing that many factors influence on the process, affecting the productivity, such as shot density, penetration depth, hole diameter, etc. The objective of this paper is to present the results of some parametric study to evaluate the influence of some parameters related to the explosive charges on well productivity, since there are many types of charges with different properties, which provide specific characteristics to the perforated area. For that purpose, a commercial program will be used, which allows the simulation of the flow problem, along with a finite element mesh generator that uses a pre-processor and a program that enables the construction of reservoir, well and perforation models. It can be observed that the penetration depth has bigger influence than the hole diameter, being an important factor when choosing the charge to be used in the project. (author)

  1. Biogeochemical anomaly above oil-containing structures in an arid zone. [Growth stimulation of plants by sodium naphthenate used for prospecting

    Energy Technology Data Exchange (ETDEWEB)

    Grishchenko, O.M.

    1983-01-01

    Visual biological anomalies above the oil-containing structures are characterized by bright green coloring of the vegetation cover, gigantism of the plants, extended vegetation period of the plants, deformity of the plants, etc. Biological anomalies are associated with geological features and are observed only above the zone of fault disorders of the earth's crust, above deep faults. A conclusion is drawn about the presence above the oil-bearing structures in the arid zone of a biogeochemical anomaly whose origin is explained by the biological activity of oil and its derivatives. The petroleum growth matter is the sodium salt of naphthene acid, a growth stimulator of plants and animals. The oils of the USSR contain 0.8-4.8% naphthene acids, which effuse through the faults into the root area levels of the soil. As a result of stimulation of growth and development by the petroleum growth matter, the vegetation period of the plants is prolonged. Under the influence of natural petroleum growth substances, the height and productivity of the anomalous plants increases 2-3-fold. Formation and manifestation of signs of biogeochemical anomalies above the oil-bearing structures in the arid zone predetermine the following conditions: presence of fault disorders of the earth's crust; salinity of the root area of the soil layer necessary for neutralization of the naphthene acids with subsequent formation of the biologically active naphthenates; aridity of the desert landscape; plain relief excluding color diversity in vegetation cover because of nonuniform wetting, etc. The established biogeochemical anomaly can be used in prospecting and exploration of oil, gas and bitumen, and also in determining the fault disorders of the earth's crust.

  2. Lacunarity of geophysical well logs in the Cantarell oil field, Gulf of Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Arizabalo, Ruben Dario [Instituto Mexicano del Petroleo, Mexico, D.F. (Mexico); Oleschko, Klavdia [Centro de Geociencias, Universidad Nacional Autonoma de Mexico, Juriquilla, Queretaro (Mexico); Korvin, Gabor [King Fahd University, Dhahran (Saudi Arabia); Lozada, Manuel [Instituto Mexicano del Petroleo, Mexico, D.F. (Mexico); Castrejon, Ricardo [Facultad de Ingenieria, Universidad Nacional Autonoma de Mexico, Mexico, D.F. (Mexico); Ronquillo, Gerardo [Instituto Mexicano del Petroleo, Mexico, D.F. (Mexico)

    2006-04-15

    Lacunarity and fractal variations in geophysical well logs are associated with stratigraphic and petrophysical properties of the naturally fractured Cantarell field in the Gulf of Mexico. Neutron porosity (NPHI), density (RHOB, DRHO, PEF), resistivity (LLD, LLS, MSFL), natural radioactivity (GR, CGR, URAN, POTA, THOR) and caliper (CALI) logs are studied. The resistivity logs yielded remarkably high lacunarity values, especially in the hydrocarbon source- and reservoir rocks. Lacunarity {delta} was found to depend on the resolution and radial depth of penetration of the logging method. It systematically increased in the following order: {delta}(RHOB) < {delta}(CALI) < {delta}(PEF) < {delta}(URAN) < {delta}(GR) < {delta}(NPHI) < {delta}(POTA) < {delta}(CGR) < {delta}(THOR) < {delta}(MSFL) < {delta}(DRHO) < {delta}(LLS) < {delta}(LLD). [Spanish] En este trabajo fueron analizadas las variaciones fractales y de lagunaridad de los registros geofisicos de pozo, con el fin de asociarlos con las propiedades estratigraficas y petrofisicas del yacimiento naturalmente fracturado de Cantarell, en el Golfo de Mexico. Los registros considerados fueron: porosidad neutron (NPHI), densidad (RHOB, DRHO, PEF), resistividad (LLD, LLS, MSFL), radiactividad natural (GR, CGR, URAN, POTA, THOR) y caliper (CALI). Los registros de resistividad produjeron valores de lagunaridad notablemente altos, especialmente en las rocas generadoras y almacenadoras, a diferencia de los demas registros, cuya homogeneidad de traza implico una baja lagunaridad. Los resultados indican que la lagunaridad observada depende de la resolucion y profundidad radial de penetracion del metodo geofisico estudiado y aumenta sistematicamente en el siguiente orden: {delta}(RHOB) < {delta}(CALI) < {delta}(PEF) < {delta}(URAN) < {delta}(GR) < {delta}(NPHI) < {delta}(POTA) < {delta}(CGR) < {delta}(THOR) < {delta}(MSFL) < {delta}(DRHO) < {delta}(LLS) < {delta}(LLD).

  3. Stimulated emission at 2.8 μm from Hg-based quantum well structures grown by photoassisted molecular beam epitaxy

    International Nuclear Information System (INIS)

    Giles, N.C.; Yang, Z.; Han, J.W.; Cook, J.W. Jr.; Schetzina, J.F.

    1990-01-01

    We report the first observation of stimulated emission from Hg-based quantum well structures in which the active region is a HgCdTe superlattice. The laser structures were grown on (100) CdZnTe substrates by photoassisted molecular beam epitaxy. Cleaved laser cavities were optically pumped using the 1.06 μm output from a continuous wave Nd:YAG laser. Stimulated emission cavity modes were seen at cw laser power densities as low as 3.4 kW/cm 2 and at temperatures ≥60 K

  4. Integrated 3D geology modeling constrained by facies and horizontal well data for Block M of the Orinoco heavy oil belt

    Energy Technology Data Exchange (ETDEWEB)

    Longxin, M.; Baojun, X.; Shancheng, Z.; Guoqing, H. [CNPC America Ltd., Caracas (Venezuela)

    2008-10-15

    Horizontal well drilling with cold production were used to develop most of heavy oil fields in Venezuela's Orinoco heavy oil belt. This study interpreted the horizontal well logs of Block M of the Orinoco heavy oil belt in an effort to improve production from this highly porous and permeable reservoir. The reservoir is comprised primarily of non-consolidated sandstones. A porosity calculation formula for the horizontal well without porosity logs was established based on the study of horizontal well logging data of block M in the Orinoco heavy oil belt. A high quality 3-D simulation tool was used to separate the block into several different sections. A set of methods were presented in order to identify if the well track was approaching an adjacent formation, to estimate the distance between the well track and the adjacent formation, and to correct the deep resistivity of the horizontal section affected by the adjacent formation. A set of interpretation techniques were established, based on the combination of well logging data, seismic data and the oilfield development performance data. It was concluded that the development of the precise 3D geological model helped to establish a solid foundation for guiding the well position design and the drilling of the horizontal well. It also contributed to the reservoir numerical simulation and the effective development of the oil field. 6 refs., 2 tabs., 14 figs.

  5. Stimulation of liver IGF-1 expression promotes peak bone mass achievement in growing rats: a study with pomegranate seed oil.

    Science.gov (United States)

    Bachagol, Deepa; Joseph, Gilbert Stanley; Ellur, Govindraj; Patel, Kalpana; Aruna, Pamisetty; Mittal, Monika; China, Shyamsundar Pal; Singh, Ravendra Pratap; Sharan, Kunal

    2018-02-01

    Peak bone mass (PBM) achieved at adulthood is a strong determinant of future onset of osteoporosis, and maximizing it is one of the strategies to combat the disease. Recently, pomegranate seed oil (PSO) has been shown to have bone-sparing effect in ovariectomized mice. However, its effect on growing skeleton and its molecular mechanism remain unclear. In the present study, we evaluated the effect of PSO on PBM in growing rats and associated mechanism of action. PSO was given at various doses to 21-day-old growing rats for 90 days by oral gavage. The changes in bone parameters were assessed by micro-computed tomography and histology. Enzyme-linked immunosorbent assay was performed to analyze the levels of serum insulin-like growth factor type 1 (IGF-1). Western blotting from bone and liver tissues was done. Chromatin immunoprecipitation assay was performed to study the histone acetylation levels at IGF-1 gene. The results of the study show that PSO treatment significantly increases bone length, bone formation rate, biomechanical parameters, bone mineral density and bone microarchitecture along with enhancing muscle and brown fat mass. This effect was due to the increased serum levels of IGF-1 and stimulation of its signaling in the bones. Studies focusing on acetylation of histones in the liver, the major site of IGF-1 synthesis, showed enrichment of acetylated H3K9 and H3K14 at IGF-1 gene promoter and body. Further, the increased acetylation at H3K9 and H3K14 was associated with a reduced HDAC1 protein level. Together, our data suggest that PSO promotes the PBM achievement via increased IGF-1 expression in liver and IGF-1 signaling in bone. Copyright © 2017 Elsevier Inc. All rights reserved.

  6. Methodologies, solutions, and lessons learned from heavy oil well testing with an ESP, offshore UK in the Bentley field, block 9/3b

    Energy Technology Data Exchange (ETDEWEB)

    Brennan, Barny; Lucas-Clements, Charles; Kew, Steve [Xcite Energy Resources (United Kingdom); Shumakov, Yakov; Camilleri, Lawrence; Akuanyionwu, Obinna; Tonoglu, Ahmet [Schlumberger (United Kingdom)

    2011-07-01

    Over the past decade, there has been an increase in hydrocarbon demand that led to the production of heavy oil fields in the United Kingdom continental shelf (UKCS). Most of the activity has been confined to exploration and appraisal drilling, the reason being the high uncertainty of the reservoir and fluid properties. Due to the operational complexity inherent to heavy oil, the use of conventional appraisal-well testing technology is limited. A novel technique developed to determine the most appropriate technology for testing wells with heavy oil using an electrical submersible pump (ESP) is presented in this paper. This technique was applied in the Bentley field. Some of the technical challenges include, maintaining fluid mobility using a surface-testing equipment, obtaining accurate flow measurements, a short weather window, and oil and gas separation for metering. Combining technologies such as dual-energy gamma ray venturi multiphase flowmeter, realtime monitoring, and ESP completion made it possible to execute the well test.

  7. Macondo-1 well oil-derived polycyclic aromatic hydrocarbons in mesozooplankton from the northern Gulf of Mexico

    Science.gov (United States)

    Mitra, Siddhartha; Kimmel, David G.; Snyder, Jessica; Scalise, Kimberly; McGlaughon, Benjamin D.; Roman, Michael R.; Jahn, Ginger L.; Pierson, James J.; Brandt, Stephen B.; Montoya, Joseph P.; Rosenbauer, Robert J.; Lorenson, T.D.; Wong, Florence L.; Campbell, Pamela L.

    2012-01-01

    Mesozooplankton (>200 μm) collected in August and September of 2010 from the northern Gulf of Mexico show evidence of exposure to polycyclic aromatic hydrocarbons (PAHs). Multivariate statistical analysis revealed that distributions of PAHs extracted from mesozooplankton were related to the oil released from the ruptured British Petroleum Macondo-1 (M-1) well associated with the R/VDeepwater Horizon blowout. Mesozooplankton contained 0.03–97.9 ng g−1 of total PAHs and ratios of fluoranthene to fluoranthene + pyrene less than 0.44, indicating a liquid fossil fuel source. The distribution of PAHs isolated from mesozooplankton extracted in this study shows that the 2010 Deepwater Horizon spill may have contributed to contamination in the northern Gulf of Mexico ecosystem.

  8. Stimulated emission in heterostructures with double InGaAs/GaAsSb/GaAs quantum wells, grown on GaAs and Ge/Si(001) substrates

    Energy Technology Data Exchange (ETDEWEB)

    Yablonsky, A. N., E-mail: yablonsk@ipm.sci-nnov.ru; Morozov, S. V.; Gaponova, D. M.; Aleshkin, V. Ya. [Russian Academy of Sciences, Institute for Physics of Microstructures (Russian Federation); Shengurov, V. G.; Zvonkov, B. N.; Vikhrova, O. V.; Baidus’, N. V. [Lobachevsky State University of Nizhny Novgorod (Russian Federation); Krasil’nik, Z. F. [Russian Academy of Sciences, Institute for Physics of Microstructures (Russian Federation)

    2016-11-15

    We report the observation of stimulated emission in heterostructures with double InGaAs/GaAsSb/GaAs quantum wells, grown on Si(001) substrates with the application of a relaxed Ge buffer layer. Stimulated emission is observed at 77 K under pulsed optical pumping at a wavelength of 1.11 μm, i.e., in the transparency range of bulk silicon. In similar InGaAs/GaAsSb/GaAs structures grown on GaAs substrates, room-temperature stimulated emission is observed at 1.17 μm. The results obtained are promising for integration of the structures into silicon-based optoelectronics.

  9. Crumb waste tire rubber surface modification by plasma polymerization of ethanol and its application on oil-well cement

    Science.gov (United States)

    Xiaowei, Cheng; Sheng, Huang; Xiaoyang, Guo; Wenhui, Duan

    2017-07-01

    Crumb waste tire rubber (WTR) was pretreated by oxygen low temperature plasma (LTP) and modified by LTP polymerization process of ethanol monomer to improve the adhesion property with oil-well cement matrix and the mechanical properties of cement. The surface properties of modified crumb WTR and the mechanical properties and structures of modified oil-well cement were investigated by means of contact angle measurement, dispersion test, attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS), mechanics performance tests, permeability test and scanning electron microscopy (SEM). It was demonstrated that LTP treatment changed both the surface composition and roughness. The contact angle of pretreated crumb WTR dramatically fell from 122° to 34°, and sample with ethanol LPT polymer film decreased even further to 11°. The ATR-FTIR and XPS analysis results demonstrated that hydrophilic groups, such as -COOH, C-OH, and -CHO, were introduced on the WTR surface. The oxygen atomic percent increased from 8.11% to 14.50% and 24.83%. The mechanical properties, porosity and permeability of raw cement were compared to samples modified by untreated crumb WTR, pretreated crumb WTR and ethanol LTP polymerization treated crumb WTR. It was found that after 28 days, the compressive strength of the samples with the untreated crumb WTR decreased to 80% with respect to raw cement. The tensile strength and flexural strength also had a slight reduction compared with the raw cement. On the contrary, after 28 days, the tensile strength of cement modified by LTP polymerization treated WTR increased 11.03% and 13.36%, and the flexural strength increased 9.65% and 7.31%, respectively. A decrease in the compressive strength also occurred but was inconspicuous. A tight interface bonding for ethanol LTP polymerization treated WTR with cement matrix was observed via an SEM image.

  10. Evolution of the Macondo well blowout: simulating the effects of the circulation and synthetic dispersants on the subsea oil transport.

    Science.gov (United States)

    Paris, Claire B; Hénaff, Matthieu Le; Aman, Zachary M; Subramaniam, Ajit; Helgers, Judith; Wang, Dong-Ping; Kourafalou, Vassiliki H; Srinivasan, Ashwanth

    2012-12-18

    During the Deepwater Horizon incident, crude oil flowed into the Gulf of Mexico from 1522 m underwater. In an effort to prevent the oil from rising to the surface, synthetic dispersants were applied at the wellhead. However, uncertainties in the formation of oil droplets and difficulties in measuring their size in the water column, complicated further assessment of the potential effect of the dispersant on the subsea-to-surface oil partition. We adapted a coupled hydrodynamic and stochastic buoyant particle-tracking model to the transport and fate of hydrocarbon fractions and simulated the far-field transport of the oil from the intrusion depth. The evaluated model represented a baseline for numerical experiments where we varied the distributions of particle sizes and thus oil mass. The experiments allowed to quantify the relative effects of chemical dispersion, vertical currents, and inertial buoyancy motion on oil rise velocities. We present a plausible model scenario, where some oil is trapped at depth through shear emulsification due to the particular conditions of the Macondo blowout. Assuming effective mixing of the synthetic dispersants at the wellhead, the model indicates that the submerged oil mass is shifted deeper, decreasing only marginally the amount of oil surfacing. In this scenario, the oil rises slowly to the surface or stays immersed. This suggests that other mechanisms may have contributed to the rapid surfacing of oil-gas mixture observed initially. The study also reveals local topographic and hydrodynamic processes that influence the oil transport in eddies and multiple layers. This numerical approach provides novel insights on oil transport mechanisms from deep blowouts and on gauging the subsea use of synthetic dispersant in mitigating coastal damage.

  11. Structural analysis of expandable tubes for oil wells; Analise estrutural de tubos expansiveis para pocos de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Aguiar, Ana Carolina Caldas; Antoun Netto, Theodoro [Universidade Federal do Rio de Janeiro (Brazil)], e-mails: carolinaaguiar@lts.coppe.ufrj.br, tanetto@lts.coppe.ufrj.br

    2009-06-15

    Solid expandable tube technology has many advantages when compared to conventional well bores. The tube expansion in situ assists the development of reservoirs in many challenging scenarios facing the oil industry today, such as in the pre-salt layer, HPHT wells, deep reservoirs, or ultra-deep water. Furthermore, this procedure has good compatibility with directional and horizontal wells and facilitates side-track operations. Although tube expansion is an attractive approach, there is a necessity to better understand its influence on the tube mechanical strength. This study carried out tests and numerical analyses to determine the effect of parameters such as diameter-to-thickness ratio and expansion rate on the collapse resistance of expandable tubes. An experimental apparatus was designed and built to reproduce full-scale tube expansion. Three, 2-meter long specimens were expanded 10% of their original diameters and subjected to hydrostatic pressure inside a vessel until collapse. Three non-expanded tubes were also tested for comparison. At the same time, non-linear numerical models were developed using the finite element method. After calibration, they were used to further analyze the mechanical behavior of solid expandable tubes and the influence of expansion on their resistance to collapse. (author)

  12. Smart cement modified with iron oxide nanoparticles to enhance the piezoresistive behavior and compressive strength for oil well applications

    International Nuclear Information System (INIS)

    Vipulanandan, C; Mohammed, A

    2015-01-01

    In this study, smart cement with a 0.38 water-to-cement ratio was modified with iron oxide nanoparticles (NanoFe 2 O 3 ) to have better sensing properties, so that the behavior can be monitored at various stages of construction and during the service life of wells. A series of experiments evaluated the piezoresistive smart cement behavior with and without NanoFe 2 O 3 in order to identify the most reliable sensing properties that can also be relatively easily monitored. Tests were performed on the smart cement from the time of mixing to a hardened state behavior. When oil well cement (Class H) was modified with 0.1% of conductive filler, the piezoresistive behavior of the hardened smart cement was substantially improved without affecting the setting properties of the cement. During the initial setting the electrical resistivity changed with time based on the amount of NanoFe 2 O 3 used to modify the smart oil well cement. A new quantification concept has been developed to characterize the smart cement curing based on electrical resistivity changes in the first 24 h of curing. Addition of 1% NanoFe 2 O 3 increased the compressive strength of the smart cement by 26% and 40% after 1 day and 28 days of curing respectively. The modulus of elasticity of the smart cement increased with the addition of 1% NanoFe 2 O 3 by 29% and 28% after 1 day and 28 days of curing respectively. A nonlinear curing model was used to predict the changes in electrical resistivity with curing time. The piezoresistivity of smart cement with NanoFe 2 O 3 was over 750 times higher than the unmodified cement depending on the curing time and nanoparticle content. Also the nonlinear stress–strain and stress–change in resistivity relationships predicated the experimental results very well. Effects of curing time and NanoFe 2 O 3 content on the model parameters have been quantified using a nonlinear model. (paper)

  13. Well performance model

    International Nuclear Information System (INIS)

    Thomas, L.K.; Evans, C.E.; Pierson, R.G.; Scott, S.L.

    1992-01-01

    This paper describes the development and application of a comprehensive oil or gas well performance model. The model contains six distinct sections: stimulation design, tubing and/or casing flow, reservoir and near-wellbore calculations, production forecasting, wellbore heat transmission, and economics. These calculations may be performed separately or in an integrated fashion with data and results shared among the different sections. The model analysis allows evaluation of all aspects of well completion design, including the effects on future production and overall well economics

  14. Drilling and geophysical logs of the tophole at an oil-and-gas well site, Central Venango County, Pennsylvania

    Science.gov (United States)

    Williams, John H.; Bird, Philip H.; Conger, Randall W.; Anderson, J. Alton

    2014-01-01

    In a study conducted by the U.S. Geological Survey, in cooperation with the Pennsylvania Department of Conservation and Natural Resources, Bureau of Topographic and Geologic Survey, drilling and geophysical logs were used to characterize the geohydrologic framework and the freshwater and saline-water zones penetrated by the tophole at an oil-and-gas well site in central Venango County, Pennsylvania. The geohydrologic setting of the well site is typical of the dissected Appalachian Plateau underlain by Pennsylvanian and Mississippian sandstone and shale. The drilling, gamma, and acoustic-televiewer logs collected from the 575-foot deep tophole define the penetrated Pennsylvanian and Mississippian stratigraphic units and their lithology. The caliper, video, and acoustic-televiewer logs delineate multiple bedding-related and high-angle fractures in the lower Pottsville Group and Shenango Formation from 22 to 249 feet below land surface. The caliper and acoustic-televiewer logs indicate a sparsity of fractures below 249 feet below land surface in the lowermost Shenango Formation, Cuyahoga Group, Corry Sandstone, “Drake Well” formation, and upper Riceville Formation.

  15. Oils

    Energy Technology Data Exchange (ETDEWEB)

    Fabbri, S

    1909-11-29

    Mineral, shale, and like oils are treated successively with sulfuric acid, milk of lime, and a mixture of calcium oxide, sodium chloride, and water, and finally a solution of naphthalene in toluene is added. The product is suitable for lighting, and for use as a motor fuel; for the latter purpose, it is mixed with a light spirit.

  16. Reclamation of oil and gas well sites on privately-owned land in Alberta: An evaluation of benefits and costs

    International Nuclear Information System (INIS)

    Bates, L.A.

    1994-01-01

    In Alberta, ca 24,000 oil/gas well sites will be abandoned over the next 10 years. There is concern that the expense to reclaim the surface lands at these sites to current standards represents a substantial opportunity cost to industry and the provincial economy. The economic costs and benefits associated with regulation of such reclamation activity are examined and the impacts of surface access regulations on the reclamation process are discussed. Cost benefit analysis is not easily applied to environmental regulation where some extra-market benefits and costs are intangible and/or unmeasurable. Although this qualifies the results, it appears that the costs of wellsite reclamation exceed the benefits. Costs are defined as reclamation expenses; benefits are defined as the real estate value of the land, or the net present value of agricultural land rentals. An effort has been made to provide a proxy for the extra-market value of the land to the landowner. The continuation of full surface access compensation for nonproducing wells can result in negative incentive effects that reduce allocative efficiency of reclamation regulation. Reclamation costs are correlated with well age and surface access payments, but not with agricultural land use or geographic region. This suggests that reclamation standards designed to reclaim well sites to the same productive capacity as site-adjacent land is not driving reclamation effort. Rather, landowners have negotiated substantial annual surface lease payments and may also be demanding greater reclamation effort, either to maximize compensation due to higher expectations. Methods of reducing these negative incentive effects to better achieve reclamation goals are suggested. 49 refs., 9 figs., 17 tabs

  17. Exploring the efficacy of a 5-day course of transcranial direct current stimulation (TDCS) on depression and memory function in patients with well-controlled temporal lobe epilepsy.

    Science.gov (United States)

    Liu, Anli; Bryant, Andrew; Jefferson, Ashlie; Friedman, Daniel; Minhas, Preet; Barnard, Sarah; Barr, William; Thesen, Thomas; O'Connor, Margaret; Shafi, Mouhsin; Herman, Susan; Devinsky, Orrin; Pascual-Leone, Alvaro; Schachter, Steven

    2016-02-01

    Depression and memory dysfunction significantly impact the quality of life of patients with epilepsy. Current therapies for these cognitive and psychiatric comorbidities are limited. We explored the efficacy and safety of transcranial direct current stimulation (TDCS) for treating depression and memory dysfunction in patients with temporal lobe epilepsy (TLE). Thirty-seven (37) adults with well-controlled TLE were enrolled in a double-blinded, sham-controlled, randomized, parallel-group study of 5 days of fixed-dose (2 mA, 20 min) TDCS. Subjects were randomized to receive either real or sham TDCS, both delivered over the left dorsolateral prefrontal cortex. Patients received neuropsychological testing and a 20-minute scalp EEG at baseline immediately after the TDCS course and at 2- and 4-week follow-up. There was improvement in depression scores immediately after real TDCS, but not sham TDCS, as measured by changes in the Beck Depression Inventory (BDI change: -1.68 vs. 1.27, pTDCS as a safe and well-tolerated nonpharmacologic approach to improving depressive symptoms in patients with well-controlled TLE. However, there were no changes in memory function immediately following or persisting after a stimulation course. Further studies may determine optimal stimulation parameters for maximal mood benefit. Copyright © 2015. Published by Elsevier Inc.

  18. Aerobic microbial enhanced oil recovery

    Energy Technology Data Exchange (ETDEWEB)

    Torsvik, T. [Univ. of Bergen (Norway); Gilje, E.; Sunde, E.

    1995-12-31

    In aerobic MEOR, the ability of oil-degrading bacteria to mobilize oil is used to increase oil recovery. In this process, oxygen and mineral nutrients are injected into the oil reservoir in order to stimulate growth of aerobic oil-degrading bacteria in the reservoir. Experiments carried out in a model sandstone with stock tank oil and bacteria isolated from offshore wells showed that residual oil saturation was lowered from 27% to 3%. The process was time dependent, not pore volume dependent. During MEOR flooding, the relative permeability of water was lowered. Oxygen and active bacteria were needed for the process to take place. Maximum efficiency was reached at low oxygen concentrations, approximately 1 mg O{sub 2}/liter.

  19. Acute and subchronic toxicity as well as mutagenic evaluation of essential oil from turmeric (Curcuma longa L).

    Science.gov (United States)

    Liju, Vijayasteltar B; Jeena, Kottarapat; Kuttan, Ramadasan

    2013-03-01

    The present study investigated the acute, subchronic and genotoxicity of turmeric essential oil (TEO) from Curcuma longa L. Acute administration of TEO was done as single dose up to 5 g of TEO per kg body weight and subchronic toxicity study for thirteen weeks was done by daily oral administration of TEO at doses 0.1, 0.25 and 0.5 g/kg b.wt. in Wistar rats. There were no mortality, adverse clinical signs or changes in body weight; water and food consumption during acute as well as subchronic toxicity studies. Indicators of hepatic function such as aspartate aminotransferase (AST), alanine amino transferase (ALT) and alkaline phosphatase (ALP) were unchanged in treated animals compared to untreated animals. Oral administration of TEO for 13 weeks did not alter total cholesterol, triglycerides, markers of renal function, serum electrolyte parameters and histopathology of tissues. TEO did not produce any mutagenicity to Salmonella typhimurium TA-98, TA-100, TA-102 and TA-1535 with or without metabolic activation. Administration of TEO to rats (1 g/kg b.wt.) for 14 days did not produce any chromosome aberration or micronuclei in rat bone marrow cells and did not produce any DNA damage as seen by comet assay confirming the non toxicity of TEO. Copyright © 2012 Elsevier Ltd. All rights reserved.

  20. Study on properties and testing methods of thermo-responsive cementing system for well cementing in heavy oil thermal recovery

    Science.gov (United States)

    Li, Lianjiang

    2017-08-01

    In this paper, thermo-responsive cement slurry system were being developed, the properties of conventional cement slurry, compressive strength high temperature of cement sheath, mechanical properties of cement sheath and thermal properties of cement sheath were being tested. Results were being used and simulated by Well-Life Software, Thermo-responsive cement slurry system can meet the requirements of heavy oil thermal recovery production. Mechanical and thermal properties of thermo-responsive cement sheath were being tested. Tensile fracture energy of the thermo-responsive cement sheath is larger than conventional cement. The heat absorption capacity of conventional cement sheath is larger than that of thermo-responsive cement sheath, this means more heat is needed for the unit mass once increasing 1.0 °C, which also indicates that thermo-responsive cement own good heat insulating and preservation effects. The heat conductivity coefficient and thermal expansion coefficient of thermo-responsive cement is less than and conventional cement, this means that thermo-responsive cement have good heat preservation and insulation effects with good thermal expansion stabilities.

  1. The development and testing of a fieldworthy system of improved fluid pumping device and liquid sensor for oil wells. Fourth quarter technical progress report, 1991

    Energy Technology Data Exchange (ETDEWEB)

    Buckman, W.G.

    1991-12-31

    A major expenditure to maintain oil and gas leases is the support of pumpers, those individuals who maintain the pumping systems on wells to achieve optimum production. Many leases are marginal and are in remote areas and this requires considerable driving time for the pumper. The Air Pulse Oil Pump System is designed to be an economical system for the shallow stripper wells. To improve on the economics of this system, we have designed a Remote Oil Field Monitor and Controller to enable us to acquire data from the lease to our central office at anytime and to control the pumping activities from the central office by using a personal computer. The advent and economics of low-power microcontrollers have made it feasible to use this type of system for numerous remote control systems. We can also adapt this economical system to monitor and control the production of gas wells and/or pump jacks.

  2. Well blowout rates and consequences in California Oil and Gas District 4 from 1991 to 2005: Implications for geological storage of carbon dioxide

    Energy Technology Data Exchange (ETDEWEB)

    Jordan, Preston; Jordan, Preston D.; Benson, Sally M.

    2008-05-15

    Well blowout rates in oil fields undergoing thermally enhanced recovery (via steam injection) in California Oil and Gas District 4 from 1991 to 2005 were on the order of 1 per 1,000 well construction operations, 1 per 10,000 active wells per year, and 1 per 100,000 shut-in/idle and plugged/abandoned wells per year. This allows some initial inferences about leakage of CO2 via wells, which is considered perhaps the greatest leakage risk for geological storage of CO2. During the study period, 9% of the oil produced in the United States was from District 4, and 59% of this production was via thermally enhanced recovery. There was only one possible blowout from an unknown or poorly located well, despite over a century of well drilling and production activities in the district. The blowout rate declined dramatically during the study period, most likely as a result of increasing experience, improved technology, and/or changes in safety culture. If so, this decline indicates the blowout rate in CO2-storage fields can be significantly minimized both initially and with increasing experience over time. Comparable studies should be conducted in other areas. These studies would be particularly valuable in regions with CO2-enhanced oil recovery (EOR) and natural gas storage.

  3. Identifying and Allocating Geodetic Systems to historical oil gas wells by using high-resolution satellite imagery

    Science.gov (United States)

    Alvarez, Gabriel O.

    2018-05-01

    Hydrocarbon exploration in Argentina started long before the IGM created a single, high-precision geodetic reference network for the whole country. Several geodetic surveys were conducted in every producing basin, which have ever since then supported well placement. Currently, every basin has a huge amount of information referenced to the so-called "local" geodetic systems, such as Chos Malal - Quiñi Huao in the Neuquén Basin, and Pampa del Castillo in the San Jorge Basin, which differ to a greater or lesser extent from the national Campo Inchauspe datum established by the IGM in 1969 as the official geodetic network. However, technology development over the last few years and the expansion of satellite positioning systems such as GPS resulted in a new world geodetic order. Argentina rapidly joined this new geodetic order through the implementation of a new national geodetic system by the IGM: POSGAR network, which replaced the old national Campo Inchauspe system. However, this only helped to worsen the data georeferencing issue for oil companies, as a third reference system was added to each basin. Now every basin has a local system, the national system until 1997 (Campo Inchauspe), and finally the newly created POSGAR network national satellite system, which is geocentric unlike the former two planimetric datums. The purpose of this paper is to identify and allocate geodetic systems of coordinates to historical wells, whose geodetic system is missing or has been erroneously allocated, by using currently available technological resources such as geographic information systems and high-resolution satellite imagery.

  4. Oils

    Energy Technology Data Exchange (ETDEWEB)

    Cobbett, G T.B.

    1907-07-08

    Crude petroleum having a density of 850 to 900 is purified with sulfuric acid, decanted, mixed with benzine or petrol, and again treated with sulfuric acid and decanted. The remaining acid and coloring-matter are removed by washing with water, or treating with oxalic acid, zinc carbonate, lead carbonate, calcium carbonate, or oxide of zinc. The product is used as a fuel for internal-combustion engines. Specifications No. 28,104, A.D. 1906, and No. 12,606, A.D. 1907, are referred to. According to the Provisional Specification, the process is applicable to shale or schist oil.

  5. Dietary supplementation with fish oil prevents high fat diet-induced enhancement of sensitivity to the locomotor stimulating effects of cocaine in adolescent female rats.

    Science.gov (United States)

    Serafine, Katherine M; Labay, Caitlin; France, Charles P

    2016-08-01

    Eating a diet high in fat can lead to obesity, chronic metabolic disease, and increased inflammation in both the central and peripheral nervous systems. Dietary supplements that are high in omega-3 polyunsaturated fatty acids can reduce or prevent these negative health consequences in rats. Eating high fat chow also increases the sensitivity of rats to behavioral effects of drugs acting on dopamine systems (e.g., cocaine), and this effect is greatest in adolescent females. The present experiment tested the hypothesis that dietary supplementation with fish oil prevents high fat chow induced increases in sensitivity to cocaine in adolescent female rats. Female Sprague-Dawley rats (post-natal day 25-27) ate standard laboratory chow (5.7% fat), high fat chow (34.4% fat), or high fat chow supplemented with fish oil (20% w/w). Cocaine dose dependently (1-17.8mg/kg) increased locomotion and induced sensitization across 6 weeks of once-weekly testing in all rats; however, these effects were greatest in rats eating high fat chow. Dietary supplementation with fish oil prevented enhanced locomotion and sensitization in rats eating high fat chow. There were no differences in inflammatory markers in plasma or the hypothalamus among dietary conditions. These results demonstrate that dietary supplementation with fish oil can prevent high fat diet-induced sensitization to cocaine, but they fail to support the view that these effects are due to changes in proinflammatory cytokines. These data add to a growing literature on the relationship between diet and drug abuse and extend the potential health benefits of fish oil to stimulant drug abuse prevention. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

  6. Fluvoxamine-based corrosion inhibitors for J55 steel in aggressive oil and gas well treatment fluids

    Directory of Open Access Journals (Sweden)

    E.B. Ituen

    2017-09-01

    Full Text Available Fluvoxamine (FLU, a non-toxic compound was investigated as an alternative anti-corrosive additive for inhibition of J55 steel corrosion in acidic oil well treatment fluids. The aggressive fluid was simulated using 15% and 1 M HCl. Corrosion of the steel was monitored by Electrochemical Impedance Spectroscopy (EIS, Potentiodynamic Polarization (PDP, Linear Polarization Resistance (LPR, Electrochemical Frequency Modulation (EFM and Weight Loss (WL techniques. UV–Vis spectroscopy provided evidence of formation of a complex surface film due to adsorption of FLU on the J55 steel surface. The adsorption process was both physical and chemical in mechanism as best approximated by the Langmuir adsorption isotherm. The adsorption was also spontaneous and exothermic in the direction of increase in entropy of the bulk phase. Maximum inhibition efficiency was obtained with 1.0 μM FLU and decreased from 91.5% to 78.0% when concentration of HCl was increased from 1 M to 15% at 30 °C. Effectiveness of FLU declined with an increase in temperature and improved with an increase in concentration of FLU. Blending of FLU with some intensifiers improved the efficiency from 68% and 40% to 88% and 72% in 1 M and 15% HCl respectively at 90 °C. EIS measurement reveals that the corrosion process was controlled by charge transfer process. PDP measurements showed that FLU acts as a mixed type inhibitor. Inhibition efficiency values obtained from the different techniques were comparable. SEM micrographs of J55 steel surface indicate good surface protection of FLU. Theoretical calculations were performed using Material Studio Acceryls 7.0 to relate electronic properties of FLU with its structure.

  7. Water Well Locations - Conservation Wells

    Data.gov (United States)

    NSGIC Education | GIS Inventory — The conservation well layer identifies the permitted surface location of oil and gas conservation wells that have not been plugged. These include active, regulatory...

  8. Report on the explosion, fire, and oil spill resulting in one fatality and injury on September 21, 1978, at Well 6 of Cavern 6 at the West Hackberry, Louisiana, oil storage site of the strategic petroleum reserve. Volume I

    Energy Technology Data Exchange (ETDEWEB)

    1978-11-01

    The following report is the independent product of the Accident Investigation Committee which was commissioned by the Department of Energy following the accident on September 21, 1978, at the Strategic Petroleum Reserve site at West Hackberry, Louisiana. This Committee is charged with the task of determining the nature, extent, and causes of that accident, which resulted in loss of life, injury and property damage, and the need for corrective action. A nonburning oil spill went into nearby Black Lake, but was contained by the deployment of a series of oil spill containment booms and a prevailing wind from the northeast that kept the oil spill in a restricted area near shore. Because of the rapid and effective containment and cleanup of the oil spill by the Rapid Response Team, it appears very likely at this time that Black Lake will not sustain any permanent environmental damage. Cavern 6 initially contained approximately 7,000,000 barrels of oil at a pressure of 650 psig measured at the well head. As of September 29, 1978, the Strategic Petroleum Reserve Office - New Orleans (SPRO) estimated that oil expulsion from Cavern 6 was 67,510 barrels. Of this, 34,620 barrels of oil are accounted for, including 31,200 barrels of oil released into Black Lake and subsequently recovered. The remainder (32,890 barrels) was assumed by SPRO to have been burned. The total loss is presently estimated by the Accident Investigation Committee 's consultant to be $12 million. An assessment of the technical problems present at the time of the accident is given. Recommendations for improved safety procedures are included.

  9. Hydration kinetics study of class G oil-well cement and olivine nano-silica mixtures at 20–60 °C

    NARCIS (Netherlands)

    Quercia Bianchi, G.; Brouwers, H.J.H.; Sobolev, K.; Shah, S.P.

    2015-01-01

    In this study the heat evolution of standard density slurries (1.89 g/cm3) of Class G oil-well cement and olivine nano-silica additions (0.5–2.0 % bwoc), cured under different temperatures (20–60 °C) and atmospheric pressure, were examined by isothermal calorimetry. Under isothermal and isobaric

  10. A Comparison Study of Growth Factor Expression following Treatment with Transcutaneous Electrical Nerve Stimulation, Saline Solution, Povidone-Iodine, and Lavender Oil in Wounds Healing

    Directory of Open Access Journals (Sweden)

    Adalet Koca Kutlu

    2013-01-01

    Full Text Available This study compared the effects of transcutaneous electrical nerve stimulation (TENS, saline solution (SS, povidone-iodine (PI, and lavender oil (Lavandula angustifolia through expression of growth factors in a rat model of wound healing. Six experimental groups were established, each containing 8 rats: a healthy group with no incision wounds, an incision-control group, an incision and TENS group, an incision and SS group, an incision and PI group, and an incision and lavender oil group. Experiments continued for 5 days, after which the skin in the excision area was removed. Tissue concentrations of epidermal growth factor (EGF and platelet-derived growth factor (PDGF-A were measured using enzyme-linked immunosorbent assay (ELISA. Tissue expressions of EGF, PDGF-A, and fibroblast growth factor (FGF-2 were determined using immunohistochemistry. Wound closure progressed more rapidly in the TENS and lavender oil groups than in the control and other study groups. In particular, PDGF-A expressions in the dermis and EGF expression in the epidermis were significantly intense in the TENS group (P<0.05. In addition, ELISA levels of growth factors such as PDGF-A and EGF were significantly higher in TENS group compared to the control group (P<0.05. These immunohistochemical and ELISA results suggest that TENS may improve wound healing through increasing growth factors in the dermis and epidermis more than other topical applications.

  11. Evaluation of the aging of polymeric drilling fluids to oil wells; Avaliacao do envelhecimento de fluidos de perfuracao polimericos para pocos de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Farias, K.V.; Amorim, L.V. [Universidade Federal de Campina Grande, PB (Brazil). Unidade Academica de Engenharia Mecanica, UAEM/CCT - UFCG], e-mail: kassie@dem.ufcg.edu.br; Leite, R.S. [Universidade Federal de Campina Grande, PB (Brazil). Graduacao Engenharia de Materiais; Lira, H.L. [Universidade Federal de Campina Grande, PB (Brazil). Unidade Academica de Engenharia de Materiais, UAEMa/ CCT - UFCG

    2010-07-01

    The aim of this work is to evaluate the aging of polymeric drilling fluids to oil wells, from the rheological, filtration and lubricity properties in the temperatures 100 degree F ({approx} 38 degree C) and 150 degree F ({approx} 66 degree C). The results had been compared with a standard fluid used for the oil industry and had evidenced that the polymeric fluids had presented good thermal stability, presenting a small reduction in the rheological properties and better values of lubricity coefficient that a reference fluid. (author)

  12. Enhanced heavy oil recovery for carbonate reservoirs integrating cross-well seismic–a synthetic Wafra case study

    KAUST Repository

    Katterbauer, Klemens

    2015-07-14

    Heavy oil recovery has been a major focus in the oil and gas industry to counter the rapid depletion of conventional reservoirs. Various techniques for enhancing the recovery of heavy oil were developed and pilot-tested, with steam drive techniques proven in most circumstances to be successful and economically viable. The Wafra field in Saudi Arabia is at the forefront of utilizing steam recovery for carbonate heavy oil reservoirs in the Middle East. With growing injection volumes, tracking the steam evolution within the reservoir and characterizing the formation, especially in terms of its porosity and permeability heterogeneity, are key objectives for sound economic decisions and enhanced production forecasts. We have developed an integrated reservoir history matching framework using ensemble based techniques incorporating seismic data for enhancing reservoir characterization and improving history matches. Examining the performance on a synthetic field study of the Wafra field, we could demonstrate the improved characterization of the reservoir formation, determining more accurately the position of the steam chambers and obtaining more reliable forecasts of the reservoir’s recovery potential. History matching results are fairly robust even for noise levels up to 30%. The results demonstrate the potential of the integration of full-waveform seismic data for steam drive reservoir characterization and increased recovery efficiency.

  13. Do energy prices stimulate food price volatility? Examining volatility transmission between US oil, ethanol and corn markets

    NARCIS (Netherlands)

    Gardebroek, C.; Hernandez, M.A.

    2013-01-01

    This paper examines volatility transmission in oil, ethanol and corn prices in the United States between 1997 and 2011. We follow a multivariate GARCH approach to evaluate the level of interdependence and the dynamics of volatility across these markets. Preliminary results indicate a higher

  14. Do energy prices stimulate food price volatility? Examining volatility transmission between US oil, ethanol and corn markets

    NARCIS (Netherlands)

    Gardebroek, C.; Hernandez, M.A.

    2012-01-01

    This paper examines volatility transmission in oil, ethanol and corn prices in the United States between 1997 and 2011. We follow a multivariate GARCH approach to evaluate the level of interdependence and the dynamics of volatility across these markets. Preliminary results indicate a higher

  15. Do energy prices stimulate food price volatility? Examining volatility transmission between US oil, ethanol and corn markets

    NARCIS (Netherlands)

    Hernandez, M.A.; Gardebroek, C.

    2012-01-01

    This paper examines volatility transmission in oil, ethanol and corn prices in the United States between 1997 and 2011. We follow a multivariate GARCH approach to evaluate the level of interdependence and the dynamics of volatility across these markets. The estimation results indicate a higher

  16. A Hybrid Approach Based on the Combination of Adaptive Neuro-Fuzzy Inference System and Imperialist Competitive Algorithm: Oil Flow Rate of the Wells Prediction Case Study

    Directory of Open Access Journals (Sweden)

    Shahram Mollaiy Berneti

    2013-04-01

    Full Text Available In this paper, a novel hybrid approach composed of adaptive neuro-fuzzy inference system (ANFIS and imperialist competitive algorithm is proposed. The imperialist competitive algorithm (ICA is used in this methodology to determine the most suitable initial membership functions of the ANFIS. The proposed model combines the global search ability of ICA with local search ability of gradient descent method. To illustrate the suitability and capability of the proposed model, this model is applied to predict oil flow rate of the wells utilizing data set of 31 wells in one of the northern Persian Gulf oil fields of Iran. The data set collected in a three month period for each well from Dec. 2002 to Nov. 2010. For the sake of performance evaluation, the results of the proposed model are compared with the conventional ANFIS model. The results show that the significant improvements are achievable using the proposed model in comparison with the results obtained by conventional ANFIS.

  17. Optical properties of chromophoric dissolved organic matter (CDOM) in surface and pore waters adjacent to an oil well in a southern California salt marsh.

    Science.gov (United States)

    Bowen, Jennifer C; Clark, Catherine D; Keller, Jason K; De Bruyn, Warren J

    2017-01-15

    Chromophoric dissolved organic matter (CDOM) optical properties were measured in surface and pore waters as a function of depth and distance from an oil well in a southern California salt marsh. Higher fluorescence and absorbances in pore vs. surface waters suggest soil pore water is a reservoir of CDOM in the marsh. Protein-like fluorophores in pore waters at distinct depths corresponded to variations in sulfate depletion and Fe(II) concentrations from anaerobic microbial activity. These variations were supported by fluorescence indexes and are consistent with differences in optical molecular weight and aromaticity indicators. Fluorescence indices were consistent with autochthonous material of aquatic origin in surface waters, with more terrestrial, humified allochthonous material in deeper pore waters. CDOM optical properties were consistent with significantly enhanced microbial activity in regions closest to the oil well, along with a three-dimensional excitation/emission matrix fluorescence spectrum peak attributable to oil, suggesting anaerobic microbial degradation of oil. Copyright © 2016 Elsevier Ltd. All rights reserved.

  18. Polycyclic hydrocarbon biomarkers confirm selective incorporation of petroleum in soil and kangaroo rat liver samples near an oil well blowout site in the western San Joaquin Valley, California

    International Nuclear Information System (INIS)

    Kaplan, I.; Lu, S.T.; Lee, R.P.; Warrick, G.

    1996-01-01

    Following an accidental oil well blow out at an oil field in the western part of the San Joaquin Valley, soil samples and specimens of Heermann's kangaroo rats (Dipodomys heermanni) were collected from two oil-impacted areas and one control area. Fingerprinting by GC-MS and quantitative evaluation of metabolized petroleum hydrocarbons was performed on oil, soil extracts, and rat livers. A liver from a domestically raised rabbit was used as an experimental control. The results show that there is no significant incorporation of PAHs or low molecular weight n-alkanes (C 13 --C 25 ) into the liver tissues. The C 25 --C 35 n-alkane range for all soil samples, kangaroo rat livers, and rabbit liver, is dominated by a high abundance of C 27 , C 29 , C 31 , and C 33 hydrocarbons typical of epicuticular plant waxes. In all liver tissue samples, squalene, the cholesterol precursor, is the dominant hydrocarbon. Although evidence is lacking for metabolism of PAHs and paraffinic petroleum hydrocarbons, very strong evidence is available for incorporation of a set of polycyclic hydrocarbons (biomarkers) belonging to the terpane, sterane, and monoaromatic and triaromatic sterane families, identified by ion monitoring at 191, 217, 253, and 231 m/z, respectively. Because these hydrocarbons are not known to exist in the biosphere, but are only synthesized during oil- and coal-forming processes, their presence in the liver samples constitutes proof for crude oil incorporation into tissues. This conclusion is further substantiated by the selective incorporation of only the 20S enantiomer of C 28 and C 29 steranes and aromatic steranes into the livers, with the exclusion of the 20R enantiomer. The results from the study conclusively demonstrate that polycyclic hydrocarbon biomarkers provide excellent indices for proof of petroleum exposure and metabolism in some terrestrial herbivores

  19. Oil Well Bottom Hole Locations, This GIS data set was produced as a general reference for the Department of Natural Resources, the oil and gas industry, environmental and regulatory agencies, landowners, and the public., Published in 2007, 1:24000 (1in=2000ft) scale, Louisiana State University (LSU).

    Data.gov (United States)

    NSGIC Education | GIS Inventory — Oil Well Bottom Hole Locations dataset current as of 2007. This GIS data set was produced as a general reference for the Department of Natural Resources, the oil and...

  20. Development and characterization of high collapse boron alloys heat treated pipes for oil wells; Tubos de aco TiB para aplicacao em revestimento de pocos de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Moreira, Fabio A.; Silva, Ronaldo; Chad, Luis [Tenaris Confab, Pindamonhangaba SP (Brazil); Fritz, Marcelo C. [Tenaris Confab, Pindamonhangaba SP (Brazil). Dept. de Engenharia do Produto

    2008-07-01

    The utilization of OCTG (Oil Country Tubular Goods) pipes will increase with the discovery of new oil wells in ultra deep waters. This study aims to evaluate the mechanical and microstructural performance of welded and heat treated pipes through quenching and tempering using a steel project based in titanium/boron for casing pipes. The objective of this development is to present a set of techniques used during the manufacturing of heated treated ERW pipes boron allowing, discussing mechanical and metallurgical aspects of the steel project, coil conformation, heat treatment and test procedures. The results are within the limits set by the API 5CT standard. It was found that the pipes obtained good geometry and uniformity of mechanical properties, showing that this product can be applied safely and reliability as wells' casing. (author)

  1. Artificial lifting supervision: successes solutions apply for 3.000 oil wells; Supervisao na elevacao artificial: uma solucao aplicada com sucesso em 3.000 pocos de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Costa, Rutacio O. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil); Souza, Rodrigo B. [RN TECNOLOGIA, Natal, RN (Brazil); Maitelli, Andre L. [Universidade Federal do Rio Grande do Norte, Natal, RN (Brazil)

    2008-07-01

    The gathering of information in industrial automation is essential to maintain and control the industrial processes. In the automation of oil wells, each artificial elevation method has its own variables to be monitored. Thus, several automation companies have developed specific controllers with its own communication protocol and supervisory software. However, in an ideal case, all information about oil elevation should be available in one single application. The SISAL is a SCADA system able to collect processes data and deliver them to the users or other system, regardless of the technique used for artificial elevation, controllers and connecting devices to the wells. This paper is about the application, progress and results using this software in PETROBRAS. (author)

  2. Dietary fish oil delays hypoxic skeletal muscle fatigue and enhances caffeine-stimulated contractile recovery in the rat in vivo hindlimb.

    Science.gov (United States)

    Peoples, Gregory E; McLennan, Peter L

    2017-06-01

    Oxygen efficiency influences skeletal muscle contractile function during physiological hypoxia. Dietary fish oil, providing docosahexaenoic acid (DHA), reduces the oxygen cost of muscle contraction. This study used an autologous perfused rat hindlimb model to examine the effects of a fish oil diet on skeletal muscle fatigue during an acute hypoxic challenge. Male Wistar rats were fed a diet rich in saturated fat (SF), long-chain (LC) n-6 polyunsaturated fatty acids (n-6 PUFA), or LC n-3 PUFA DHA from fish oil (FO) (8 weeks). During anaesthetised and ventilated conditions (normoxia 21% O 2 (SaO 2 -98%) and hypoxia 14% O 2 (SaO 2 -89%)) the hindlimb was perfused at a constant flow and the gastrocnemius-plantaris-soleus muscle bundle was stimulated via sciatic nerve (2 Hz, 6-12V, 0.05 ms) to established fatigue. Caffeine (2.5, 5, 10 mM) was supplied to the contracting muscle bundle via the arterial cannula to assess force recovery. Hypoxia, independent of diet, attenuated maximal twitch tension (normoxia: 82 ± 8; hypoxia: 41 ± 2 g·g -1 tissue w.w.). However, rats fed FO sustained higher peak twitch tension compared with the SF and n-6 PUFA groups (P recovery was enhanced in the FO-fed animals (SF: 41 ± 3; n-6 PUFA: 40 ± 4; FO: 52 ± 7% recovery; P < 0.05). These results support a physiological role of DHA in skeletal muscle membranes when exposed to low-oxygen stress that is consistent with the attenuation of muscle fatigue under physiologically normoxic conditions.

  3. Anxiolytic-like effect of inhalation of essential oil from Lavandula officinalis: investigation of changes in 5-HT turnover and involvement of olfactory stimulation.

    Science.gov (United States)

    Takahashi, Mizuho; Yamanaka, Ayako; Asanuma, Chihiro; Asano, Hiroko; Satou, Tadaaki; Koike, Kazuo

    2014-07-01

    Essential oil extracted from Lavandula officinalis (LvEO) has a long history of usage in anxiety alleviation with good evidence to support its use. However, findings and information regarding the exact pathway involved and mechanism of action remain inconclusive. Therefore, we aimed to (1) reveal the influence of olfactory stimulation, and (2) determine whether the serotonergic system is involved in the anxiolytic effect of LvEO when it is inhaled. To this end, we first compared the anxiety-related behaviors of normosmic and anosmic mice. LvEO inhalation caused notable elevation in anxiety-related parameters with or without olfactory perception, indicating that olfactory stimulation is not necessarily required for LvEO to be effective. Neurochemical analysis of the serotonin (5-HT) turnover rate, accompanied by EPM testing, was then performed. LvEO significantly increased the striatal and hippocampal levels of 5-HT and decreased turnover rates in accordance with the anxiolytic behavioral changes. These results, together with previous findings, support the hypothesis that serotonergic neurotransmission plays a certain role in the anxiolytic properties of LvEO.

  4. Transient model for free fall effect during cementing operations in oil wells; Modelo transiente para o efeito de queda livre durante operacoes de cimentacao em pocos de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Poggio, Junior, Ademar; Lage, Antonio Carlos V.M.; Campos, Wellington [PETROBRAS, Rio de Janeiro (Brazil). Centro de Pesquisas. Setor de Tecnologia de Perfuracao

    1990-12-31

    This paper presents a mathematical model for the simulation of cementing operations in oil wells. The downward flow of fluids in the casing and the upward flow of fluids in the annulus is further complicated by fluid free fall, which creates a vacuum at the well head. The basic equations were derived from the mass and momentum conservation laws by means of a macroscopic balance. The simulator is used to predict pressures and flow rates during the operation. (author) 6 refs., 6 figs., 1 tab.

  5. Transient model for free fall effect during cementing operations in oil wells; Modelo transiente para o efeito de queda livre durante operacoes de cimentacao em pocos de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Poggio Junior, Ademar; Lage, Antonio Carlos V.M.; Campos, Wellington [PETROBRAS, Rio de Janeiro (Brazil). Centro de Pesquisas. Setor de Tecnologia de Perfuracao

    1989-12-31

    This paper presents a mathematical model for the simulation of cementing operations in oil wells. The downward flow of fluids in the casing and the upward flow of fluids in the annulus is further complicated by fluid free fall, which creates a vacuum at the well head. The basic equations were derived from the mass and momentum conservation laws by means of a macroscopic balance. The simulator is used to predict pressures and flow rates during the operation. (author) 6 refs., 6 figs., 1 tab.

  6. Chitosan encapsulation of essential oil "cocktails" with well-defined binary Zn(II)-Schiff base species targeting antibacterial medicinal nanotechnology.

    Science.gov (United States)

    Halevas, Eleftherios; Nday, Christiane M; Chatzigeorgiou, Evanthia; Varsamis, Vasileios; Eleftheriadou, Despoina; Jackson, Graham E; Litsardakis, Georgios; Lazari, Diamanto; Ypsilantis, Konstantinos; Salifoglou, Athanasios

    2017-11-01

    The advent of biodegradable nanomaterials with enhanced antibacterial activity stands as a challenge to the global research community. In an attempt to pursue the development of novel antibacterial medicinal nanotechnology, we herein a) synthesized ionic-gelated chitosan nanoparticles, b) compared and evaluated the antibacterial activity of essential oils extracted from nine different herbs (Greek origin) and their combinations with a well-defined antibacterial Zn(II)-Schiff base compound, and c) encapsulated the most effective hybrid combination of Zn(II)-essential oils inside the chitosan matrix, thereby targeting well-formulated nanoparticles of distinct biological impact. The empty and loaded chitosan nanoparticles were physicochemically characterized by FT-IR, Thermogravimetric Analysis (TGA), Scanning Electron Microscopy (SEM), with the entrapment and drug release studies being conducted through UV-Visible and atomic absorption techniques. The antimicrobial properties of the novel hybrid materials were demonstrated against Gram positive (S. aureus, B. subtilis, and B. cereus) and Gram negative (E. coli and X. campestris) bacteria using modified agar diffusion methods. The collective physicochemical profile of the hybrid Zn(II)-essential oil cocktails, formulated so as to achieve optimal activity when loaded to chitosan nanoparticles, signifies the importance of design in the development of efficient nanomedicinal pharmaceuticals a) based on both natural products and biogenic metal ionic cofactors, and b) targeting bacterial infections and drug resistance. Copyright © 2017 Elsevier Inc. All rights reserved.

  7. Radioprotection guidelines to the elaboration of a specific standard for the licensing of radioactive facilities on the practice of oil and gas well logging

    International Nuclear Information System (INIS)

    Gomes, Rogerio dos Santos; Gomes, Joana D'Arc Ramos Lopes; Costa, Mara Lucia de Lara; Miranda, Marcia Valeria F.E. Sa

    2011-01-01

    The regulatory process in oil and gas well logging has shown the need for specific standard for the issuance of a license authorizing the use of sealed sources in well logging activities, in order to guarantee the quality of many factors from the point of view of radiation protection. Currently, have been used only generic radiation protection standards, but are not comprehensive or technically suitable for a well logging licensing purpose. The lack of a specific standard for licensing in radioactive well logging operations in Brazil, weakens the nuclear regulatory body in your aim of regulate and licensing the activity. This work establish, as main objective, a guideline for the future Brazilian radioprotection code in well logging operations, presenting relevant aspects not covered by generic radiation protection standards. (author)

  8. Radioprotection guidelines to the elaboration of a specific standard for the licensing of radioactive facilities on the practice of oil and gas well logging

    International Nuclear Information System (INIS)

    Gomes, Rogerio dos Santos; Gomes, Joana D'Arc Ramos Lopes; Costa, Mara Lucia de Lara; Miranda, Marcia Valeria F.E. Sa

    2011-01-01

    The regulatory process in oil and gas well logging has shown the need for specific standard for the issuance of a license authorizing the use of sealed sources in well logging activities, in order to guarantee the quality of many factors from the point of view of radiation protection. Currently, have been used only generic radiation protection standards, but are not comprehensive or technically suitable for a well logging licensing purpose. The lack of a specific standard for licensing in radioactive well logging operations in Brazil, weakens the nuclear regulatory body in your aim of regulate and licensing the activity. This work establish, as main objective, a guideline for the future Brazilian radioprotection code in well logging operations, presenting relevant aspects not covered by genetic radiation protection standards. (author)

  9. 75 FR 66776 - BOEMRE Information Collection Activity: 1010-0043, Oil and Gas Well-Workover Operations...

    Science.gov (United States)

    2010-10-29

    .... Review well-workover diagrams and procedures to ensure the safety of well-workover operations. Verify... burden for this information collection is a total of 24,719 hours. The following chart details the... for well-workovers on a pressure chart or with a digital recorder; certify the information is correct...

  10. Field-scale evidence for biogeophysical signatures resulting from natural attenuation of a well characterized crude oil spill

    Science.gov (United States)

    Slater, L. D.; Revil, A.; Atekwana, E. A.; Mewafy, F.; Bekins, B. A.; Cozzarelli, I.; Herkelrath, W. N.; Skold, M.; Ntarlagiannis, D.; Trost, J.; Erickson, M.; Heenan, J. W.; Lane, J. W.; Werkema, D. D.

    2012-12-01

    Recent biogeophysical research has indicated that unique geophysical signatures are associated with the long-term biodegradation of organic contaminants. However, field-scale demonstrations of the presence of these signatures at sites of organic contamination are lacking. For the last three years, we have performed geophysical measurements at the National Crude Oil Spill Fate and Natural Attenuation Research Site, a unique field laboratory situated just outside of Bemidji, MN. At this site, a ruptured pipeline spilled 1,700,000 L of crude oil into an uninhabited area in 1979. Natural attenuation of the spill has been extensively documented and a geochemical database extending back over 20 years is available to constrain interpretation of the geophysical signatures. We report compelling evidence of a transient geobattery associated with biodegradation of this mature hydrocarbon spill. Using an array of boreholes, self-potential measurements acquired from land surface, passing through the smear zone, capture a diagnostic dipole (peak to peak voltages up to 64 mV) indicating a current source centered on the smear zone, with anodic and cathodic reactions below and above the smear zone respectively. Down borehole measurements reveal that the smear zone is characterized by high magnetic susceptibility (MS); laboratory measurements show that this MS enhancement results from precipitation of iron mineral byproducts of biodegradation. These iron minerals presumably facilitate the electron transport between anode and cathode required to support a geobattery. Furthermore, laboratory and field-scale complex resistivity measurements reveal an enhancement in the complex surface conductivity within the smear zone most likely due to these biodegradation byproducts. The geobattery is not permanent, but instead periodically shuts down, presumably due to changes in the gradient of the redox species driving anodic and cathodic reactions. Gas samples show that conditions are anaerobic

  11. Cellobiohydrolase B of Aspergillus niger over-expressed in Pichia pastoris stimulates hydrolysis of oil palm empty fruit bunches.

    Science.gov (United States)

    Woon, James Sy-Keen; Mackeen, Mukram M; Illias, Rosli M; Mahadi, Nor M; Broughton, William J; Murad, Abdul Munir Abdul; Abu Bakar, Farah Diba

    2017-01-01

    Aspergillus niger , along with many other lignocellulolytic fungi, has been widely used as a commercial workhorse for cellulase production. A fungal cellulase system generally includes three major classes of enzymes i.e., β-glucosidases, endoglucanases and cellobiohydrolases. Cellobiohydrolases (CBH) are vital to the degradation of crystalline cellulose present in lignocellulosic biomass. However, A. niger naturally secretes low levels of CBH. Hence, recombinant production of A. niger CBH is desirable to increase CBH production yield and also to allow biochemical characterisation of the recombinant CBH from A. niger . In this study, the gene encoding a cellobiohydrolase B ( cbh B) from A. niger ATCC 10574 was cloned and expressed in the methylotrophic yeast Pichia pastoris X-33. The recombinant CBHB was purified and characterised to study its biochemical and kinetic characteristics. To evaluate the potential of CBHB in assisting biomass conversion, CBHB was supplemented into a commercial cellulase preparation (Cellic ® CTec2) and was used to hydrolyse oil palm empty fruit bunch (OPEFB), one of the most abundant lignocellulosic waste from the palm oil industry. To attain maximum saccharification, enzyme loadings were optimised by response surface methodology and the optimum point was validated experimentally. Hydrolysed OPEFB samples were analysed using attenuated total reflectance FTIR spectroscopy (ATR-FTIR) to screen for any compositional changes upon enzymatic treatment. Recombinant CBHB was over-expressed as a hyperglycosylated protein attached to N -glycans. CBHB was enzymatically active towards soluble substrates such as 4-methylumbelliferyl-β-D-cellobioside (MUC), p -nitrophenyl-cellobioside ( p NPC) and p -nitrophenyl-cellobiotrioside ( p NPG3) but was not active towards crystalline substrates like Avicel ® and Sigmacell cellulose. Characterisation of purified CBHB using MUC as the model substrate revealed that optimum catalysis occurred at 50 °C and

  12. Using Oil and Gas Well Log Records to Understand Possible Connections Between Wastewater Injection Zones and Usable Groundwater Aquifers in California

    Science.gov (United States)

    Shimabukuro, D.; Haugen, E. A.; Battistella, C.; Treguboff, E. W.; Kale, J. M.

    2015-12-01

    Although the disposal of produced water in wastewater injection wells has been occurring in California for decades, it is not clear whether injected fluids may be migrating into usable groundwater aquifers. One problem is the poor characterization of federally-protected (oil and gas well records collected by the California Division of Oil, Gas, and Geothermal Resources (DOGGR). These scanned records contain two useful sources of information. First, geophysical well logs, such those measuring resistivity and porosity, can be used to determine aquifer salinity. This allows a three-dimensional understanding of the distribution of protected groundwater. Second, driller's logs contain lithological descriptions at depth. These lithologies can be used to construct a three-dimensional texture model, which can then be used in a groundwater flow model. A large number of undergraduate researchers at CSU Sacramento and CSU Long Beach have been collecting information on well records in the Ventura Basin and the Southern San Joaquin Valley. Each well record is examined with basic metadata entered into an online database in an effort to identify appropriate geophysical well logs and driller's logs. High-quality driller's logs are coded and used to create three-dimensional framework models for each well field. The geophysical logs are digitized and will be used to determine aquifer salinity. In addition, we are using information from the DOGGR well records to investigate wellbore integrity, waste disposal and waterflood injection volumes, and the possibility of induced seismicity. This project is part of the broader effort of the California State Water Resources Control Board to implement Senate Bill 4.

  13. Decision 99-28: Mobil Oil Canada, Ltd., and Mobil Resources Ltd., - application for a well licence to drill a critical sour gas well LSD 4-36-27-28 W4, Crossfield Field, application No. 1037560

    International Nuclear Information System (INIS)

    1999-01-01

    On 12 February 1999, Mobil submitted Application No. 1037560 to the Alberta Energy and Utilities (EUB) Board on a routine basis, pursuant to Section 2.020 of the Oil and Gas Conservation Regulations, for a well licence to drill a critical sour gas well. The well would be drilled from a surface location in Legal Subdivision (LSD) 4 of Section 36, Township 27, Range 28, West of the 4th Meridian to a bottomhole location in LDS 7-36-27-28 W4M, with an 1100 m horizontal section. The aim of the 4-36 well was to obtain gas production from the Crossfield member. On 17 February 1999, the EUB issued Well Licence No. 221575 on the understanding that there were no outstanding objections to the 4-36 well. Mobil spudded the 4-36 well on 3 March 1999, drilled to 363 m and set surface casing. The EUB subsequently received objections to the application from area residents near the proposed well location. Accordingly, pursuant to Section 43 of the Energy Resources Conservation Act, the EUB directed that a public hearing be held to consider the application. The Board assessed in detail the effects that would likely result and the mitigative measures that would have to be taken to reduce any negative effects considering: the proposed well location, impacts of the proposed well, safety of the well, and public notification and consultation. Having carefully considered all the evidence, the EUB Board determined that Application No. 1037560 met all the EUB's regulatory requirements and was satisfied that appropriate measures were taken to ensure that public safety risks and impacts were minimized

  14. 78 FR 68082 - Information Collection Activities: Oil and Gas Well-Workover Operations; Submitted for Office of...

    Science.gov (United States)

    2013-11-13

    ... crew in the event of encountering H 2 S. Review well-workover diagrams and procedures to ensure the... this information collection is a total of 53,156 hours. The following chart details the individual... and coiled tubing tests for well-workovers on a pressure chart or with a digital recorder; certify the...

  15. 75 years of Digboi oil

    Energy Technology Data Exchange (ETDEWEB)

    1965-11-01

    Oil was found in Assam, India, some 30 yr before Drake's well was sunk in the U.S., in Aug. 1859. Thus, Digboi Oil Field in Assam is 75 yr old this month. For many years it was India's only proved field, and its story is inseparable from that of exploration for oil in the subcontinent. Throughout Digboi's history an intensive research program has been undertaken to maintain production, and only recently details were published of new attempts to boost its output. A map shows the 3 major oil fields in Assam, and 3 refineries. For some years, production has been declining in the Digboi Field--it was 180,000 metric tons in 1964--although since its inception, nearly 1,000 wells have been drilled. Some of the techniques planned are already being used to stimulate output at Digboi and include gas injection, waterflooding, thermoflood methods, formation fracturing, and modernization of gas lift.

  16. Cellobiohydrolase B of Aspergillus niger over-expressed in Pichia pastoris stimulates hydrolysis of oil palm empty fruit bunches

    Directory of Open Access Journals (Sweden)

    James Sy-Keen Woon

    2017-10-01

    Full Text Available Background Aspergillus niger, along with many other lignocellulolytic fungi, has been widely used as a commercial workhorse for cellulase production. A fungal cellulase system generally includes three major classes of enzymes i.e., β-glucosidases, endoglucanases and cellobiohydrolases. Cellobiohydrolases (CBH are vital to the degradation of crystalline cellulose present in lignocellulosic biomass. However, A. niger naturally secretes low levels of CBH. Hence, recombinant production of A. niger CBH is desirable to increase CBH production yield and also to allow biochemical characterisation of the recombinant CBH from A. niger. Methods In this study, the gene encoding a cellobiohydrolase B (cbhB from A. niger ATCC 10574 was cloned and expressed in the methylotrophic yeast Pichia pastoris X-33. The recombinant CBHB was purified and characterised to study its biochemical and kinetic characteristics. To evaluate the potential of CBHB in assisting biomass conversion, CBHB was supplemented into a commercial cellulase preparation (Cellic® CTec2 and was used to hydrolyse oil palm empty fruit bunch (OPEFB, one of the most abundant lignocellulosic waste from the palm oil industry. To attain maximum saccharification, enzyme loadings were optimised by response surface methodology and the optimum point was validated experimentally. Hydrolysed OPEFB samples were analysed using attenuated total reflectance FTIR spectroscopy (ATR-FTIR to screen for any compositional changes upon enzymatic treatment. Results Recombinant CBHB was over-expressed as a hyperglycosylated protein attached to N-glycans. CBHB was enzymatically active towards soluble substrates such as 4-methylumbelliferyl-β-D-cellobioside (MUC, p-nitrophenyl-cellobioside (pNPC and p-nitrophenyl-cellobiotrioside (pNPG3 but was not active towards crystalline substrates like Avicel® and Sigmacell cellulose. Characterisation of purified CBHB using MUC as the model substrate revealed that optimum

  17. 75 FR 60800 - Discharge of Oil From Deepwater Horizon/Macondo Well, Gulf of Mexico; Intent To Conduct...

    Science.gov (United States)

    2010-10-01

    ... Section 403.161, Fla. Statutes; the Mississippi Air and Water Pollution Control Law, Miss. Code Ann. Sec... Horizon/Macondo Well, Gulf of Mexico; Intent To Conduct Restoration Planning ACTION: Notice of intent. [[Page 60801

  18. The coalification profile of the Grambach 1 exploration well - first indication of an oil kitchen in the molasse basin. Das Inkohlungsprofil der Bohrung Grambach 1 - erster Hinweis auf eine ''Oelkueche'' im Molassebecken

    Energy Technology Data Exchange (ETDEWEB)

    Hiltmann, W.; Wehner, H. (Bundesanstalt fuer Geowissenschaften und Rohstoffe, Hannover (Germany)); Kuckelkorn, K. (Niedersaechsisches Landesamt fuer Bodenforschung, Hannover (Germany))

    1999-06-01

    For the first time an exploration well beneath the German part of the Alpine overthrust zone met vitrinite reflectance values raising up to 1,6% R[sub r] - and this in a widespread tectonic high position. The interpretation as an oil and gas kitchen is confirmed by oil maturity (derived by biomarkers and carbon isotope ratios). (orig.)

  19. Effect of temperature on biodegradation of crude oil

    International Nuclear Information System (INIS)

    Zekri, A.; Chaalal, O.

    2005-01-01

    An active strain of anaerobic thermophilic bacteria was isolated from the environment of the United Arab Emirates. This project studied the effect of temperature, salinity and oil concentration on biodegradation of crude oil. Oil weight loss, microbial growth and the changes of the crude oil asphaltene concentration are used to evaluate the oil degradation by this strain. A series of batch experiments was performed to study the effects of bacteria on the degradation of crude oil. The effects of oil concentration, bacteria concentration, temperature and salinity on the biodegradation were investigated. The temperatures of the studied systems were varied between 35 and 75 o C and the salt concentrations were varied between 0 and 10%. Oil concentrations were ranged from 5 to 50% by volume. Experimental work showed the bacteria employed in this project were capable of surviving the harsh environment and degrading the crude oil at various conditions. Increasing the temperature increases the rate of oil degradation by bacteria. Increasing the oil concentration in general decreases the rate of bacteria oil degradation. Salinity plays a major role on the acceleration of biodegradation process of crude oil. An optimum salinity should be determined for every studied system. The finding of this project could be used in either the treatment of oil spill or in-situ stimulation of heavy oil wells. (author)

  20. Sealing wells with gel

    Energy Technology Data Exchange (ETDEWEB)

    Lopez, E C

    1967-10-01

    A new system is being used in Mexico to temporarily plug producing wells. The temporary seal is a gel with a catalyst. The use of this temporary plug allows gas-lift wells to be taken off production in order to carry out emergency repairs. The gel solidifies by the action of the catalyst to a high temperature (70 - 150/sup 0/C). By locating the bottom of the tubing at the top of the production interval, the gel material will go into the permeable formation, and immediately set. When the gel has solidified, it seals off the horizon that must not be stimulated, and leaves the others exposed to the acid action. When the treatment is finished, the gel, by action of the catalyst, is liquefied and removed from the formation, being produced with the oil.

  1. Oil biodegradation

    NARCIS (Netherlands)

    Rahsepar, Shokouhalsadat; Langenhoff, Alette A.M.; Smit, Martijn P.J.; Eenennaam, van Justine S.; Murk, Tinka; Rijnaarts, Huub H.M.

    2017-01-01

    During the Deepwater Horizon (DwH) oil spill, interactions between oil, clay particles and marine snow lead to the formation of aggregates. Interactions between these components play an important, but yet not well understood, role in biodegradation of oil in the ocean water. The aim of this study

  2. 26 CFR 1.611-2 - Rules applicable to mines, oil and gas wells, and other natural deposits.

    Science.gov (United States)

    2010-04-01

    ... prospective mineral, account should be taken of probable increases or decreases as indicated by the operating..., segregate and have readily available at his principal place of business, all the supporting data (listed in... productivity to the end of the taxable year, the average number of wells producing during each year, and the...

  3. 75 FR 61624 - Promotion of Development, Reduction of Royalty Rates for Stripper Well and Heavy Oil Properties

    Science.gov (United States)

    2010-10-06

    ...-241A.00] RIN 1004-AE04 Promotion of Development, Reduction of Royalty Rates for Stripper Well and Heavy... economy, productivity, competition, jobs, the environment, public health or safety, or State, local, or..., investment, productivity, innovation, or the ability of U.S.-based enterprises to compete with foreign-based...

  4. Natural gas as an alternative to crude oil in automotive fuel chains well-to-wheel analysis and transition strategy development

    International Nuclear Information System (INIS)

    Hekkert, M.P.; Hendriks, F.H.J.F.; Faaij, A.P.C.; Neelis, M.L.

    2005-01-01

    Road transport produces significant amounts of CO 2 by using crude oil as primary energy source. A reduction of CO 2 emissions can be achieved by implementing alternative fuel chains. This article studies CO 2 emissions and energy efficiencies by means of a well to wheel analysis of alternative automotive fuel chains, using natural gas (NG) as an alternative primary energy source to replace crude oil. The results indicate that NG-based hydrogen applied in fuel cell vehicles (FCVs) lead to largest CO 2 emission reductions (up to 40% compared to current practice). However, large implementation barriers for this option are foreseen, both technically and in terms of network change. Two different transition strategies are discussed to gradually make the transition to these preferred fuel chains. Important transition technologies that are the backbone of these routes are traditional engine technology fuelled by compressed NG and a FCV fuelled by gasoline. The first is preferred in terms of carbon emissions. The results furthermore indicate that an innovation in the conventional chain, the diesel hybrid vehicle, is more efficient than many NG-based chains. This option scores well in terms of carbon emissions and implementation barriers and is a very strong option for the future

  5. A Review of the Evaluation, Control, and Application Technologies for Drill String Vibrations and Shocks in Oil and Gas Well

    Directory of Open Access Journals (Sweden)

    Guangjian Dong

    2016-01-01

    Full Text Available Drill string vibrations and shocks (V&S can limit the optimization of drilling performance, which is a key problem for trajectory optimizing, wellbore design, increasing drill tools life, rate of penetration, and intelligent drilling. The directional wells and other special trajectory drilling technologies are often used in deep water, deep well, hard rock, and brittle shale formations. In drilling these complex wells, the cost caused by V&S increases. According to past theories, indoor experiments, and field studies, the relations among ten kinds of V&S, which contain basic forms, response frequency, and amplitude, are summarized and discussed. Two evaluation methods are compared systematically, such as theoretical and measurement methods. Typical vibration measurement tools are investigated and discussed. The control technologies for drill string V&S are divided into passive control, active control, and semiactive control. Key methods for and critical equipment of three control types are compared. Based on the past development, a controlling program of drill string V&S is devised. Application technologies of the drill string V&S are discussed, such as improving the rate of penetration, controlling borehole trajectory, finding source of seismic while drilling, and reducing the friction of drill string. Related discussions and recommendations for evaluating, controlling, and applying the drill string V&S are made.

  6. Phytotoxicology section investigation in the vicinity of Riddell Hanna No. 1 oil well, Lot 11, Conc 13, Chatham Twp., Kent County, 1990

    International Nuclear Information System (INIS)

    1992-02-01

    A survey was conducted around the Riddell Hanna No.1 oil well in the Windsor district of Ontario to determine the degree and extent of damage that may have been caused to a farm field in the vicinity of the well. The well has been operating for decades, and occasionally has been purged by pumping out brine. In the past (possibly up to ten years ago) the brine was not contained but was deposited directly onto the field adjacent the well. Large patches of bare soil were evident in the soybean field immediately south of the well. Effects of the contaminant on the soybeans were clearly evident in all adjacent areas up to 3 m from the bare patches. Soil and vegetation samples were collected from affected areas and a control site. Results of analyses of electrical conductivity and sodium and chloride concentrations in soils in the vicinity of the well are presented. In the affected area, conductivity reaches six times the level expected to cause severe damage to most plants. Both Na and Cl concentrations in the plants were higher in the affected area than in the control area. The total affected area was estimated at 7,600 m 2 , of which 4,000 m 2 does not support any plant life. 3 refs., 2 figs

  7. Water and clay based drilling fluids for oil wells; Fluidos hidroargilosos para perfuracao de pocos de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Medeiros, R.C.A. de; Amorim, L.V.; Santana, L.N. de L. [Universidade Federal de Campina Grande (UFCG), PB (Brazil)], e-mail: nalealves@hotmail.com

    2008-07-01

    In the onshore drilling of wells are commonly used aqueous fluids containing bentonite clays. However, to perform their functions generally there is the necessity of additives to drilling fluids, like viscositying, filtered reducer and lubricant. Thus, this work aims to develop water and clay base drilling fluids with low solid text, and with polymeric and lubricants additives. Were studied a sample of industrialized sodium bentonite clays, three polymeric compounds in the ternary form and a sample of lubricant, in different concentrations. Were determined the flow curves, the apparent and plastic viscosities, the yield limit and gel force in Fann 35A viscometer, the filtered volume in API filter-press and the lubricity coefficient in Ofite lubricimeter. The results showed that the fluid had pseudoplastic behavior, the polymeric additives adjusts their rheological properties and filtration and the addition of 1% of lubricant is sufficient to improve the lubricity of fluids. (author)

  8. Hypermetabolic Conversion of Plant Oil into Water: Endothermic Biochemical Process Stimulated by Juvenile Hormone in the European Firebug, Pyrrhocoris apterus L.

    Science.gov (United States)

    Sláma, Karel; Lukáš, Jan

    2016-01-01

    The physiological and biochemical mechanisms that enable insects to feed on dry food to secure enough water for larval growth were investigated. The study was carried out with a plethora of physiological methods, ranging from the simple volumetric determination of O 2 consumption and water intake to more advanced methods such as scanning microrespirography and thermovision imaging of insect's body temperature. The experiments were done on the European firebug, Pyrrhocoris apterus , which feeds exclusively on dry linden seeds. In order to survive, it needs to drink water or suck a sap from plants occasionally. It was found that the young larval instars compensate the occasional water deficiency by the increased production of metabolic water. The juvenile hormone (JH)-dependent production of metabolic water, which was previously found in other species consuming dry food, was achieved in P. apterus by total metabolic combustion of the dietary lipid (neutral seed oil). The water-producing, hypermetabolic larvae were heated from inside by endothermic energy released from the uncoupling of oxidation from oxidative phosphorylation. The "warm", hypermetabolic larvae burning the dietary oil into CO 2 and water showed the increased rates of respiratory metabolism. Microrespirographic recording of these larvae revealed the ratio of the respiratory quotient (RQ, CO 2 /O 2 ) of 0.7, which indicated the breakdown of a pure triglyceride. The warm hypermetabolic larvae could be easily spotted and distinguished from the "cold" larvae on the screen of a thermovision camera. The last instar larvae lacking the JH were always only cold. They metabolized a carbohydrate substrate exclusively (RQ = 1.0), while the dietary lipid was stored in the fat body. In comparison with the hypermetabolic larvae of some other species fed on dry food, which exhibited the highest rates of O 2 consumption ever recorded in a living organism (10-20 mL O 2 /g per hour), the metabolic difference between the

  9. Contribution to the analytical and numerical evaluation of oil well equilibrium for any cross section under a uniform pressure and an anisotropic stress field

    Energy Technology Data Exchange (ETDEWEB)

    Bouziane, A.

    1989-09-01

    The integral equation, the finite element and an analytical method are used and compared to compute the state of equilibrium of an oil well. This well is of whatever cross section and is subjected to a uniform pressure and an anisotropic stress field at the infinity. In the first part, the equations of the Mechanics of deformable solids are recalled using dual vectorial spaces theory. These equations are briefly introduced by using a four spaces diagram. In the second part, an analytical method using the complex potentials developed by Muskhelishvili is used to solve the problem. In the third part, three methods of integral equations are developed (direct and indirect). The stress boundary conditions at infinity are taken into account by superimposing a particular solution to the fundamental solution. With such a method, both displacements and stresses are correctly represented as well on the boundary as inside the domain. The finite element method is developed in the fourth part. For complicate shapes of well cross section the used automatic mesh generator does not seem well adapted. In conclusion, the integral equation method gives the results which are in the best agreement with the analytical solutions.

  10. Supplementation with linoleic acid-rich soybean oil stimulates macrophage foam cell formation via increased oxidative stress and diacylglycerol acyltransferase1-mediated triglyceride biosynthesis.

    Science.gov (United States)

    Rom, Oren; Jeries, Helana; Hayek, Tony; Aviram, Michael

    2017-01-02

    During the last decades there has been a staggering rise in human consumption of soybean oil (SO) and its major polyunsaturated fatty acid linoleic acid (LA). The role of SO or LA in cardiovascular diseases is highly controversial, and their impact on macrophage foam cell formation, the hallmark of early atherogenesis, is unclear. To investigate the effects of high SO or LA intake on macrophage lipid metabolism and the related mechanisms of action, C57BL/6 mice were orally supplemented with increasing levels of SO-based emulsion or equivalent levels of purified LA for 1 month, followed by analyses of lipid accumulation and peroxidation in aortas, serum and in peritoneal macrophages (MPM) of the mice. Lipid peroxidation and triglyceride mass in aortas from SO or LA supplemented mice were dose-dependently and significantly increased. In MPM from SO or LA supplemented mice, lipid peroxides were significantly increased and a marked accumulation of cellular triglycerides was found in accordance with enhanced triglyceride biosynthesis rate and overexpression of diacylglycerol acyltransferase1 (DGAT1), the key enzyme in triglyceride biosynthesis. In cultured J774A.1 macrophages treated with SO or LA, triglyceride accumulated via increased oxidative stress and a p38 mitogen-activated protein kinase (MAPK)-mediated overexpression of DGAT1. Accordingly, anti-oxidants (pomegranate polyphenols), inhibition of p38 MAPK (by SB202190) or DGAT1 (by oleanolic acid), all significantly attenuated SO or LA-induced macrophage triglyceride accumulation. These findings reveal novel mechanisms by which supplementation with SO or LA stimulate macrophage foam cell formation, suggesting a pro-atherogenic role for overconsumption of SO or LA. © 2016 BioFactors, 43(1):100-116, 2017. © 2016 International Union of Biochemistry and Molecular Biology.

  11. Characteristics and properties of oil-well cements auditioned with blast furnace slag; Cementos petroleros con adicion de escoria de horno alto. Caracteristicas y propiedades

    Energy Technology Data Exchange (ETDEWEB)

    Sanchez, R.; Palacios, M.; Puertas, F.

    2011-07-01

    The present paper addresses the alkali activation of Portland cements containing blast furnace slag (20 and 30% by cement weight) with a view to the possible use of these materials in oil well construction. The hydration studies conducted showed that in cement/slag blends, the sodium silicate activator partially inhibited the dissolution of the silicate phases in the Portland cement, retarding cement hydration and reducing the precipitation of reaction products. Due to such partial inhibition, the cement/slag blends had significantly lower mechanical strength than Portland cements hydrated with water. {sup 2}9Si and {sup 2}7Al MAS NMR and BSE/EDX studies, in turn, showed that the CSH gel forming in the alkali-activated cement/slag pastes contained Al in tetrahedral positions and low Ca/Si ratios. (Author) 29 refs.

  12. The Influence of New Colored Light Stimulation Methods on Heart Rate Variability, Temperature, and Well-Being: Results of a Pilot Study in Humans

    Directory of Open Access Journals (Sweden)

    Daniela Litscher

    2013-01-01

    Full Text Available Changes of light intensity of different colors can shift many physiological parameters and conditions like melatonin, alertness, body temperature, heart rate (HR, and heart rate variability (HRV. The aim of this pilot study was to investigate acute temperature, HR, HRV, and state of mind reactivities after illumination with red (631 nm and blue (456 nm light (illuminance 140 lux for both. Seven healthy volunteers (5 females, 2 males; mean age ± SD 34.1 ± 11.9 years were investigated at the Medical University of Graz, using new color light panels. Significant decreases were found only after 10 min blue light stimulation in nose temperature (P=0.046, HR (P<0.05, and total HRV (P=0.029, in association with a significant alteration of the emotional state (stress level score, P=0.006. However, red light stimulation of the same persons did not induce the same effects in these parameters. The effect of blue light as environmental stimulation on human health is not clarified in detail and needs further investigations.

  13. Evaluation of polymers and polymergels for water shutoff in oil and gas wells. Literature study; Beurteilung von Gelen und Polymeren fuer Absperrmassnahmen im Bohrloch. Literaturrecherche

    Energy Technology Data Exchange (ETDEWEB)

    Lubenau, U.; Rockmann, R.; Schmitz, S.; Kretzschmar, H.J. [DBI Gas- und Umwelttechnik GmbH, Leipzig (Germany)

    2010-08-15

    The aim of this project is compilation and consolidation of knowledge about polymer technologies for water control of defined zones in wells. The first part of this review is the presentation of the best available technology together with summary and evaluation of published field test data. About 200 references of the last 20 years were included in this report. The selected references describe 80 different polymer treatments, mainly in oil wells. In this study the basic chemistry of published polymers and polymergels is described and the results of laboratory investigations are presented. The dominating systems use polyacrylamid compounds, whose properties are modified by selection of copolymers and cross-linkers. Investigations of resistance of the polymers and gels to low pH-value and high salinity are seldom published. The cited references contain almost fragmentary data that describe the geological structure, the main chemical composition and details of the handling procedure. Nevertheless viscosity and temperature behaviour of polymers are adjustable over a wide range. So the composition of the polymer system can be varied in order to fit the requirements of the field conditions. The success rate of polymer treatments correlates with the knowledge of geological and geochemical field conditions as well as the extent of preliminary investigations. It was about 75 % in the considered literature. (orig.)

  14. EVALUATION OF CEMENT THIXOTROPY FOR THE CEMENT OF OIL WELLS IN AREAS WITH LOSSES: EFFECT OF PLASTER AND DAIRY OF HIGH FURNACES

    Directory of Open Access Journals (Sweden)

    T. Bouziani

    2010-12-01

    Full Text Available Cementing of oil and gas wells can be a very delicate operation. Among the concerns of service companies, during this operation are the nature and conditions of the formations in well. This is the case of cementing operations in southern Algeria, specifically on the fields of In-Amen, where the formations in lost zones are naturally weak and highly permeable. In these areas, drilling fluids (muds and cements pumped will be, completely or partially lost, what we call "lost circulation". Thixotropic cements are useful to overcome lost circulation problems. They are characterized by a special rheological behavior, allowing it to plug lost zones when they are pumped. Our work aims to assess the thixotropy of cements perapred with two types of cement (class G Asland cement and CEM I 42.5 portland cement with the plaster, using a viscometer with coaxial cylinder (couette type. Moreover, the effect of blast furnace slag (LHF on the properties and thixotropic mixtures prepared was also studied. The results show that portland cement (available locally can produce mixes with higher and more stable thixotropy than the class G cement (from importation, which is a practical and economical for cementing job operations in wells with loss zones. The results also show that the effect of LHF is positive, since in addition to his contribution to long term performances, especially the durability of hardened concrete, it improves the thixotropy of cement made of plaster.

  15. EVALUATION OF THE THIXOTROPY OF OIL-WELL CEMENTS USED FOR CEMENTING LOST CIRCULATION ZONES: EFFECT OF PLASTER AND BLAST FURNACE SLAG

    Directory of Open Access Journals (Sweden)

    T. Bouziani

    2015-08-01

    Full Text Available Cementing of oil and gas wells can be a very delicate operation. Among the concerns of service companies, during this operation are the nature and conditions of the formations in well. This is the case of cementing operations in southern Algeria, specifically on the fields of In-Amen, where the formations in lost zones are naturally weak and highly permeable. In these areas, drilling fluids (muds and cements pumped will be, completely or partially lost, what we call "lost circulation". Thixotropic cements are useful to overcome lost circulation problems. They are characterized by a special rheological behavior, allowing it to plug lost zones when they are pumped.Our work aims to assess the thixotropy of cements perapred with two types of cement (class G Asland cement and CEM I 42.5 portland cement with the plaster, using a viscometer with coaxial cylinder (couette type. Moreover, the effect of blast furnace slag (LHF on the properties and thixotropic mixtures prepared was also studied. The results show that portland cement (available locally can produce mixes with higher and more stable thixotropy than the class G cement (from importation, which is a practical and economical for cementing job operations in wells with loss zones. The results also show that the effect of LHF is positive, since in addition to his contribution to long term performances, especially the durability of hardened concrete, it improves the thixotropy of cement made of plaster.

  16. Insulin rapidly stimulates phosphorylation of a 46-kDa membrane protein on tyrosine residues as well as phosphorylation of several soluble proteins in intact fat cells

    International Nuclear Information System (INIS)

    Haering, H.U.; White, M.F.; Machicao, F.; Ermel, B.; Schleicher, E.; Obermaier, B.

    1987-01-01

    It is speculated that the transmission of an insulin signal across the plasma membrane of cells occurs through activation of the tyrosine-specific receptor kinase, autophosphorylation of the receptor, and subsequent phosphorylation of unidentified substrates in the cell. In an attempt to identify possible substrates, the authors labeled intact rat fat cells with [ 32 P]orthophosphate and used an antiphosphotyrosine antibody to identify proteins that become phosphorylated on tyrosine residues in an insulin-stimulated way. In the membrane fraction of the fat cells, they found, in addition to the 95-kDa β-subunit of the receptor, a 46-kDa phosphoprotein that is phosphorylated exclusively on tyrosine residues. This protein is not immunoprecipitated by antibodies against different regions of the insulin receptor and its HPLC tryptic peptide map is different from the tryptic peptide map of the insulin receptor, suggesting that it is not derived from the receptor β-subunit. Insulin stimulates the tyrosine phosphorylation of the 46-kDa protein within 150 sec in the intact cell 3- to 4-fold in a dose-dependent way at insulin concentrations between 0.5 nM and 100 nM. Insulin (0.5 nM, 100 nM) stimulated within 2 min the 32 P incorporation into a 116-kDa band, a 62 kDa band, and three bands between 45 kDa and 50 kDa 2- to 10-fold. They suggest that the 46-kDa membrane protein and possibly also the soluble proteins are endogenous substrates of the receptor tyrosine kinase in fat cells and that their phosphorylation is an early step in insulin signal transmission

  17. Effect of Rock Properties on ROP Modeling Using Statistical and Intelligent Methods: A Case Study of an Oil Well in Southwest of Iran

    Science.gov (United States)

    Bezminabadi, Sina Norouzi; Ramezanzadeh, Ahmad; Esmaeil Jalali, Seyed-Mohammad; Tokhmechi, Behzad; Roustaei, Abbas

    2017-03-01

    Rate of penetration (ROP) is one of the key indicators of drilling operation performance. The estimation of ROP in drilling engineering is very important in terms of more accurate assessment of drilling time which affects operation costs. Hence, estimation of a ROP model using operational and environmental parameters is crucial. For this purpose, firstly physical and mechanical properties of rock were derived from well logs. Correlation between the pair data were determined to find influential parameters on ROP. A new ROP model has been developed in one of the Azadegan oil field wells in southwest of Iran. The model has been simulated using Multiple Nonlinear Regression (MNR) and Artificial Neural Network (ANN). By adding the rock properties, the estimation of the models were precisely improved. The results of simulation using MNR and ANN methods showed correlation coefficients of 0.62 and 0.87, respectively. It was concluded that the performance of ANN model in ROP prediction is fairly better than MNR method.

  18. Addition of polyurethane dispersions to Portland G for oil wells steam injection submitted to vapor injection; Adicao de poliuretana em dispersao a Portland G para cimentacao de pocos de petroleo sujeitos a injecao de vapor

    Energy Technology Data Exchange (ETDEWEB)

    Silva, L.B. da; Lima, F.M. de; Martinelli, A.M.; Bezerra, U.T.; Mello, D.M.A. [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil); Araujo, R.G.S. [PETROBRAS, Rio de Janeiro, RJ (Brazil)

    2004-07-01

    Portland cement is by far the most important binding material used in oil well cementing. The cement sheath is responsible for both the mechanical stability of the wellbore and zonal isolation. During primary cementing and the production lifespan of the well, the cement sheath is exposed to adverse thermo-mechanical conditions, which may crack the intrinsically brittle cement material. Cracking affects the mechanical integrity of the sheath resulting in the contamination of oil or gas pay zones, as well as in the increase of producing costs related to the extraction of pebble and water. This scenario is especially encountered in wells containing heavy oils, typical of the Northeastern region of Brazil. The objective of the present study was to improve the fracture toughness of hardened Special Portland Cement slurries by the addition of aqueous polyurethane to Portland-based slurries used in primary cementing, plug backs and squeeze operations, improving environmental and economical impacts. The results revealed that the addition of polyurethane increased the viscosity of the slurry but still within the limits established by oil well cement guidelines. No significant increase was observed in the compressive strength of the cement. However, the addition of polyurethane improved the toughness of the cement increasing its ability to withstand thermo-mechanical cycles typical of heavy oil recovery. In addition, significant reduction in permeability was observed as the contents of polyurethane increased, contributing to the reduction in set time and gas migration through the cement sheath. (author)

  19. Comparing olive oil and C4-dietary oil, a prodrug for the GPR119 agonist, 2-oleoyl glycerol, less energy intake of the latter is needed to stimulate incretin hormone secretion in overweight subjects with type 2 diabetes

    DEFF Research Database (Denmark)

    Mandøe, Mette Johannsen; Hansen, Katrine Bagge; Windeløv, Johanne Agerlin

    2018-01-01

    of common triglycerides, e.g., olive oil. SUBJECTS AND METHODS: We studied the effect over 180 min of (a) 19 g olive oil plus 200 g carrot, (b) 10.7 g C4 dietary oil plus 200 g carrot and (c) 200 g carrot, respectively, on plasma responses of gut and pancreatic hormones in 13 overweight patients with type 2...... diabetes (T2D). Theoretically, both oil meals result in formation of 7.7 g 2-OG during digestion. RESULTS: Both olive oil and C4-dietary oil resulted in greater postprandial (P ≤ 0.01) glucagon-like peptide 1 (GLP-1) and glucose-dependent insulinotropic polypeptide (GIP) responses (incremental area under...... curve (iAUC)): iAUCGLP-1: 645 ± 194 and 702 ± 97 pM × min; iAUCGIP: 4,338 ± 764 and 2,894 ± 601 pM × min) compared to the carrot meal (iAUCGLP-1: 7 ± 103 pM × min; iAUCGIP: 266 ± 234 pM × min). iAUC for GLP-1 and GIP were similar for C4-dietary oil and olive oil, although olive oil resulted in a higher...

  20. Belarus oil recovery. Final report

    International Nuclear Information System (INIS)

    1994-07-01

    The Belarus Oil Recovery study was sponsored by the Danish Energy Agency and funded by the Danish State Oestlandepulje. The technical work was carried out by COWIconsult, the Danish Geological Survey, and Odin Energi in cooperation with the Belarus State Oil Company, Belorusneft. Belarus, a republic of the former USSR, is a landlocked country with limited and declining oil production. Oil production was initially established in Belarus in 1964, and 56 oil fields have been discovered to date. Production reached a peak of approximately 60,000 barrels per day in the mid 70's, but current production is only about 15,000 bpd, well below the required amount for self sufficiency. The intent of this feasibility study was to determine ways of improving the production potential of the oil fields of Belarus with western technology in order to make Belarus less dependent on other energy resources and on outside supplies of hydrocarbons. All the oil fields in Belarus are located in the Pripyat Basin. The structural complexity of the fields under study coupled with the rather poor reservoir quality have resulted in low oil recoveries, and the aim of the study is to recommend technology which might improve the performance of these reservoirs. Improved well stimulation and water injection using modern western technology is likely to improve recovery from these reservoirs. If this technology proves successful in these fields, then it could be applied to the other larger oil fields in Belarus. It is anticipated that the documented results would enable financing full scale implementation of the technology utilised which could contribute toward the solution of Belarus' energy requirements. (EG)

  1. A Case Report of Possible Health Benefits of Extra Virgin Olive Oil

    Directory of Open Access Journals (Sweden)

    Said Shahtahmasebi

    2003-01-01

    Full Text Available The literature on the chemical analysis of cooking oils suggests that the cholesterol-reducing effect may well be due to the antioxidant agents rather than unsaturated fats. Furthermore, antioxidant agents are present in extra virgin olive oil and not in olive oil. There is some evidence, based on studies using patients, to support such a supposition. In this paper, we present a case report on the possible health effects of changing from olive oil to extra virgin olive oil. The case report is intended to raise some relevant issues to stimulate a debate and more research in this area.

  2. Cationic polyelectrolyte induced separation of some inorganic contaminants and their mixture (zirconium silicate, kaolin, K-feldspar, zinc oxide) as well as of the paraffin oil from water.

    Science.gov (United States)

    Ghimici, Luminita

    2016-03-15

    The flocculation efficiency of a cationic polyelectrolyte with quaternary ammonium salt groups in the backbone, namely PCA5 was evaluated on zirconium silicate (kreutzonit), kaolin, K- feldspar and zinc oxide (ZnO) suspensions prepared either with each pollutant or with their mixture. The effect of several parameters such as settling time, polymer dose and the pollutant type on the separation efficacy was evaluated and followed by optical density and zeta potential measurements. Except for ZnO, the interactions between PCA5 and suspended particles led to low residual turbidity values (around 4% for kreutzonit, 5% for kaolin and 8% for K-feldspar) as well as to the reduction of flocs settling time (from 1200 min to 30 min and 120 min in case of kaolinit and K-feldspar, respectively), that meant a high efficiency in their separation. The negative value of the zeta potential and flocs size measurements, at the optimum polymer dose, point to contribution from charge patch mechanism for the particles flocculation. A good efficiency of PCA5 in separation of paraffin oil (a minimum residual turbidity of 9.8%) has been also found. Copyright © 2015 Elsevier Ltd. All rights reserved.

  3. Processes of heat transference during the construction of oil wells: inverse problem; Procesos de transferencia de calor durante la construccion de pozos petroleros: problema inverso

    Energy Technology Data Exchange (ETDEWEB)

    Olea Gonzalez, Ulises

    2007-08-15

    In the oil industry and during the drilling and completion of oil wells, it is indispensable to count on reliable temperature estimations of the formation; its relevance and application are found in many areas of the geophysics, of the reservoir engineering and oil engineering. Unfortunately, the temperatures registered during the runs normally are lower than the real temperature of the formation, this is due to the fact that the times of interruption and flow circulation and circulation in the well are too short so that they do not allow the mud at the well bottom reaches the heat balance, which usually requires several days or weeks, economically non feasible situation to determine temperature profiles, since the times and costs of services of drilling would exceed the programmed technical economic limits. In order to confront this critical process a numerical code was developed, which consists of an analytical and numerical solution of the equations of heat transfer which they govern a system well-formation, which are used to model the thermal stabilization of an oil well after the drilling fluid flow has been stopped, supposing that the formation consists of an homogenous porous medium. The mathematical context is to find the initial conditions of the ensemble of partial differential equations that govern the phenomena of heat transference in the well and the formation. These equations form a bi-dimensional model in transient state. The mathematical model is established for four regions in the system well-formation and the border conditions and the initial conditions tie the partial differential equations for the well as for the formation. With the previous thing a generated methodology is obtained to determine the field of formation temperatures. Later, a particular analysis based on the thermo physical properties of the well geometry, the border conditions and the initial condition is proposed, parameter that is indeed the incognito of the problem. Ahead of

  4. Impact of bioremediation treatments on the biodegradation of buried oil and predominant bacterial populations

    International Nuclear Information System (INIS)

    Swannell, R.P.J.; Mitchell, D.J.; Waterhouse, J.C.; Miskin, I.P.; Head, I.M.; Petch, S.; Jones, D.M.; Willis, A.; Lee, K.; Lepo, J.E.

    2000-01-01

    The feasibility of using mineral fertilizers as a bioremediation treatment for oil buried in fine sediments was tested in field trials at a site in the south-west of England. The plots were divided into three blocks of four treatments including untreated, fertilized, oiled unfertilized and oiled fertilized plots. The changes in residual hydrocarbons were monitored to study the biodegradation of Arabian Light Crude Oil which is known to have a high portion of biodegradable components. Samples were extracted at random points at intervals of 0, 42 and 101 days. The analysis process identified a range of aliphatic and aromatic hydrocarbons, as well as a range of geochemical biomarkers. The final results suggested that the oil in the fertilized plots was more degraded than in the oiled, unfertilized control plots. Three way, factorial analysis of variance was used to analyse the data from the oiled fertilized and oiled unfertilized plots. No significant effect of treatment on the degradation of aromatic hydrocarbons was observed. The results also showed that oil treatment and treatment with oil and fertilizer increased the abundance of hydrocarbon-degrading bacterial population. One significant observation was that different bacterial populations were stimulated in response to oil alone and a bioremediation treatment. It was concluded that the addition of inorganic fertilizers to the oiled oxic fine sediment substantially enhanced the level of biodegradation compared to untreated oiled sediment. Bioremediation is a feasible treatment for oil spills where the oil is buried in fine sediment. 14 refs., 1 tab., 4 figs

  5. Pressure and pressure derivative analysis for vertical gas and oil wells in stress sensitive homogeneous and naturally fractured formations without type-curve matching

    International Nuclear Information System (INIS)

    Escobar, Freddy Humberto; Cantillo, Jose Humberto; Montealegre M, Matilde

    2007-01-01

    Currently, rock mechanics plays an important role in the oil industry. Effects of reservoir subsidence, compaction and dilation are being taken into account in modern reservoir management of complex systems. On the other hand, pressure well tests run in stress sensitive formations ought to be interpreted with non conventional techniques. During the last three decades, several studies relating transient pressure analysis for characterization of stress sensitive reservoirs have been introduced in the literature. Some of them deal with type curves and/or automated history matching. However, due to the nature of the problem, it does not exist a definitive study focused on the adequate characterization of reservoirs which permeability changes as fluid withdrawal advances; in this paper, the permeability modulus concept introduced by Pedroso (1986) is token as the starting basis. A great number of type curves were generated to study the behavior of the above mentioned formations under stress influence. It was found that permeability modulus, therefore permeability changes, can be correlated with the slope of the pressure derivative trend during the radial flow regime when the reservoir suffers compaction. It is also worth to mention that the time of which the minimum characteristic point of a naturally fractured formation (or the inflection point of o semi-log plot) found on the pressure derivative plot is practically the same for formations without stress influence. This contributes to the extension of the TDS technique, Tiab (1993), so a new methodology to characterize this kind of reservoirs is proposed here. This was verified by the solution of synthetic problems

  6. Assessment of stability of ceramics type perovskite, Ba{sub 2}MgWO{sub 6}, submerged in crude oil taken from oil wells of Sergipe - Brazil; Avaliacao da estabilidade de ceramicas tipo perovskita, Ba{sub 2}MgWO{sub 6}, submersas em petroleo cru retirado de pocos do estado de Sergipe - Brasil

    Energy Technology Data Exchange (ETDEWEB)

    Yadava, Y.P.; Sales, D.G.; Lima, M.M.; Ferreira, R.A.S. [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil)], e-mail: daniella_guedes@yahoo.com.br

    2008-07-01

    Oil wells are harsh environments, thus, it is necessary to find materials that are able to resist the weather imposed by these sites. Many of the new technology incorporating ceramic components because their chemical properties, electrical, mechanical, thermal and structural. The ceramics exhibit high hardness and therefore resistant to high pressure, have high melting point, resisting the high temperatures, and make inert nature in hostile environments. The ceramics, type Perovskite Ba{sub 2}MgWO{sub 6}, were submerged in crude oil for thirty days and then examined by X-ray diffraction, optical microscopy and Vickers microhardness to see if there were changes in structural characteristics, microstructural and mechanical properties. This work was evaluated and discussed by these results, the stability of these ceramics when subject to attack by crude oil taken from oil wells of land and sea state of Sergipe, Brazil. (author)

  7. Project and evaluation of a 2000 meter offshore horizontal well production extra-heavy oil; Projeto e avaliacao de um poco offshore com 2000 m de trecho horizontal produtor de oleo extra-pesado

    Energy Technology Data Exchange (ETDEWEB)

    Ueta, Eduardo M.; Kato, Edson T.; Tinoco, Francisco L.; Vieira, Paulo M.F. [PETROBRAS, Rio de Janeiro, RJ (Brazil)

    2004-07-01

    The project was proposed to acquire reservoir data, for the development of the Member (Mb) Siri in the concession of Badejo in Campos Basin, having extra-heavy oil, through long and large bore horizontal well. The main objectives were: to obtain the petrophysical properties through continuous coring of the oil and water zones; water sampling for the characterization; to verify the effective length of the horizontal well through production logging; to obtain the reservoir productivity and permeability through formation test; to obtain the oil PVT properties through monophasic sampling and to know the lateral variability of the accumulation. New technologies were used as geochemical geosteering, diversionary acidification and chemical tracer production logging. The well test analysis showed permeability and productivity values better than as expected and making possible the development of pilot project in order to evaluate the aquifer behavior, the long term well productivity and performance of the elevation and behavior of the extra-heavy oil offloading for subsequent development of the reservoir. (author)

  8. Electricity generation from enhanced geothermal systems by oilfield produced water circulating through reservoir stimulated by staged fracturing technology for horizontal wells: A case study in Xujiaweizi area in Daqing Oilfield, China

    International Nuclear Information System (INIS)

    Zhang, Yan-Jun; Li, Zheng-Wei; Guo, Liang-Liang; Gao, Ping; Jin, Xian-Peng; Xu, Tian-Fu

    2014-01-01

    In this paper, the feasibility of generating electricity from EGS (enhanced geothermal systems) by oilfield produced water circulating through reservoir stimulated by staged fracturing technology for horizontal wells is investigated based on the geological data of Xujiaweizi area, located in the Daqing Oilfield, northeast China. HDR (hot dry rock) resource potential assessment is carried out by using volumetric method. Reservoir stimulation is numerically simulated based on the geological data of well YS-1 and field fracturing experience in this region. Geometric dimensions and flow conductivity of the resulting fracture are imported into the hydro-thermal model to calculate the electricity generation potential of the proposed EGS power plant. An EGS design scheme is proposed based on the simulation results. The system is also evaluated from the economic and environmental aspects. The results indicate that HDR resource in Xujiaweizi area is of great potential for development. Through the staged fracturing technology for horizontal wells, electricity generation power of the proposed EGS project can roughly meet the commercial standard. For 20 years of continuous production, power generation from the proposed EGS power plant is economic feasible. Meanwhile, significant reductions in greenhouse gas emissions can be achieved. - Highlights: • Staged fracturing technology for horizontal well is used in HDR (hot dry rock) development. • Fracturing simulations and heat production simulations are combined. • A 3 MW power plant is designed in Xujiaweizi based on the simulation results

  9. Effect of ultrasonic intensity and frequency on oil/heavy-oil recovery from different wettability rocks

    Energy Technology Data Exchange (ETDEWEB)

    Naderi, K.; Babadagli, T. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[Alberta Univ., Edmonton, AB (Canada)

    2008-10-15

    This study identified the mechanisms that are responsible for additional oil recovery that is often observed following an earthquake. It focused on the theory that harmonics of low frequency waves create high frequency waves as they penetrate into rock formations. A series of experiments were conducted on oil-wet rocks with high oil viscosities. The objective was to better understand how ultrasonic energy affects oil recovery at core and pore scale. Cylindrical sandstone cores were placed in imbibition cells to examine how the presence of initial water saturation can affect recovery, and how the recovery changes for different oil viscosities. An increase in oil recovery was observed with ultrasonic energy in all cases. The additional recovery with ultrasonic energy lessened as the oil viscosity increased. Ultrasonic intensity and frequency were shown to be critical to the performance, which is important since ultrasonic waves have limited penetration into porous medium. This is a key disadvantage for commercializing this promising process for well stimulation. Therefore, the authors designed a set-up to measure the ultrasonic energy penetration capacity in different media, notably air, water and slurry. The set-up could identify which types of reservoirs are most suitable for ultrasonic application. Imbibition experiments revealed that ultrasonic radiation increases recovery, and is much more significant in oil wet cases, where initial water saturation facilitate oil recovery. Higher frequency showed a higher rate of recovery compared to lower frequency, but the ultimate recovery was not changed substantially. 46 refs., 1 tab., 16 figs.

  10. The coalification profile of the Grambach 1 exploration well - first indication of an oil kitchen in the molasse basin; Das Inkohlungsprofil der Bohrung Grambach 1 - erster Hinweis auf eine ``Oelkueche`` im Molassebecken

    Energy Technology Data Exchange (ETDEWEB)

    Hiltmann, W.; Wehner, H. [Bundesanstalt fuer Geowissenschaften und Rohstoffe, Hannover (Germany); Kuckelkorn, K. [Niedersaechsisches Landesamt fuer Bodenforschung, Hannover (Germany)

    1999-06-01

    For the first time an exploration well beneath the German part of the Alpine overthrust zone met vitrinite reflectance values raising up to 1,6% R{sub r} - and this in a widespread tectonic high position. The interpretation as an oil and gas kitchen is confirmed by oil maturity (derived by biomarkers and carbon isotope ratios). (orig.) [Deutsch] Erstmals traf im deutschen Teil der alpinen Ueberschiebungszone eine Bohrung ein bis 1,6% R{sub r} ansteigendes Inkohlungsprofil an und dies in einer ausgedehnten Hochscholle. Die Interpretation als `Oel- und Gaskueche` wurde durch die Reife des zugeschlossenen Erdoels (Biomarker, Kohlenstoffisotopen) bestaetigt. (orig.)

  11. Assessment of recycled PET properties for application on oil wells as sand control agents; Avaliacao de propriedades de PET reciclado para aplicacao em pocos de petroleo como agente de contencao de areia

    Energy Technology Data Exchange (ETDEWEB)

    Pereira, Alexandre Zacarias Ignacio [PETROBRAS, Rio de Janeiro, RJ (Brazil); Delpech, Marcia Cerqueira [Universidade do Estado do Rio de Janeiro (IQ/UERJ), RJ (Brazil). Inst. de Quimica], e-mail: mcd@uerj.br

    2008-07-01

    The Sand Control is fundamental for oil production in unconsolidated sandstone formations. It consists of the installation of a filter made of stainless steel screens and grained materials (sand control agents) which are, normally, high density inorganic substances (sand, ceramic, bauxite). Shallow formations, near to the sea bed, are more sensitive and need different kinds of sand control agents with low density. The objective of this work was the evaluation of recycled poly(ethylene terephthalate), PET, as sand control agent for oil wells. Pack permeability and thermal stability tests results, after up to six months of exposure to sea water and crude oil, have indicated that the recycled PET kept the necessary characteristics for the proposed application. Also, it was observed that the PET grain pack did not presented significant property modifications in the exposure conditions, when compared to the non-exposed samples. (author)

  12. Accompaniment of the biomass growth and synthesis of biosurfactants by microorganism isolated in oil wells; Acompanhamento do crescimento da biomassa e sintese de biosurfactantes por microorganismos isolados de pocos de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Lobato, Ana Katerine de Carvalho Lima; Araujo, Manuelle Meike Silva de [Rio Grande do Norte Univ., Natal, RN (Brazil). Programa de Pos-graduacao em Engenharia Quimica]. E-mail: manuelle@eq.ufrn.br; Macedo, Gorete Ribeiro de [Rio Grande do Norte Univ., Natal, RN (Brazil). Dept. de Engenharia Quimica

    2003-07-01

    Biosurfactants are structurally diversified groups of active surface molecules synthesized by microorganisms as bacteria and fungi, cultivated in several carbon sources such as sucrose and hydrocarbons. These molecules, composed by a part hydrophilic and other hydrophobic one, they act preferentially in the interface among the flowing phases with different polarities linking interfaces oil/water or water/oil reducing the superficial tensions and interfacial among these phases. They have been used in environmental applications, such as bioremediation of soils, treatment of contaminated water fountains and in cleaning process of tanks and equipment. Oil reservoirs present conditions where some microorganisms can grow. These microorganisms when isolated and cultivated at laboratory can be characterized with relation to surfactants production. In this work, microorganisms were isolated of oil wells and the biosurfactants producers were selected, among the isolated ones, to form a culture bank with potential application in environmental pollution treatment and advanced oil recovery. A microorganism stump of the developed bank was cultivated in sucrose and hydrocarbon medium and the biosurfactant production was evaluated by superficial tension measurement. The microorganism biomass production was evaluated by optical density using a spectrophotometer and the substratum consumption by Dns method. (author)

  13. Composition of natural gas and crude oil produced from 10 wells in the Lower Silurian "Clinton" Sandstone, Trumbull County, Ohio: Chapter G.7 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

    Science.gov (United States)

    Burruss, Robert A.; Ryder, Robert T.; Ruppert, Leslie F.; Ryder, Robert T.

    2014-01-01

    Natural gases and associated crude oils in the “Clinton” sandstone, Medina Group sandstones, and equivalent Tuscarora Sandstone in the northern Appalachian basin are part of a regional, continuous-type or basin-centered accumulation. The origin of the hydrocarbon charge to regional continuoustype accumulations is poorly understood. We have analyzed the molecular and stable isotopic composition of gases and oils produced from 10 wells in the “Clinton” sandstone in Trumbull County, Ohio, in an initial attempt to identify the characteristics of the accumulated fluids. The analyses show that the fluids have remarkably uniform compositions that are similar to previously published analyses of oils (Cole and others, 1987) and gases (Laughrey and Baldasarre, 1998) in Early Silurian reservoirs elsewhere in Ohio; however, geochemical parameters in the oils and gases suggest that the fluids have experienced higher levels of thermal stress than the present-day burial conditions of the reservoir rocks. The crude oils have an unusual geochemical characteristic: they do not contain detectable levels of sterane and triterpane biomarkers. The origin of these absences is unknown.

  14. 26 CFR 1.613A-0 - Limitations on percentage depletion in the case of oil and gas wells; table of contents.

    Science.gov (United States)

    2010-04-01

    .... (4) Examples. (e) Partnerships. (1) General rule. (2) Initial allocation of adjusted basis of oil or gas property among partners. (i) General rule. (ii) Allocation methods. (3) Adjustments by partnership to allocated adjusted bases. (i) Capital expenditures by partnership. (ii) Admission of a new partner...

  15. Bacterial community diversity in a low-permeability oil reservoir and its potential for enhancing oil recovery.

    Science.gov (United States)

    Xiao, Meng; Zhang, Zhong-Zhi; Wang, Jing-Xiu; Zhang, Guang-Qing; Luo, Yi-Jing; Song, Zhao-Zheng; Zhang, Ji-Yuan

    2013-11-01

    The diversity of indigenous bacterial community and the functional species in the water samples from three production wells of a low permeability oil reservoir was investigated by high-throughput sequencing technology. The potential of application of indigenous bacteria for enhancing oil recovery was evaluated by examination of the effect of bacterial stimulation on the formation water-oil-rock surface interactions and micromodel test. The results showed that production well 88-122 had the most diverse bacterial community and functional species. The broth of indigenous bacteria stimulated by an organic nutrient activator at aerobic condition changed the wettability of the rock surface from oil-wet to water-wet. Micromodel test results showed that flooding using stimulated indigenous bacteria following water flooding improved oil recovery by 6.9% and 7.7% in fractured and unfractured micromodels, respectively. Therefore, the zone of low permeability reservoir has a great potential for indigenous microbial enhanced oil recovery. Copyright © 2013 Elsevier Ltd. All rights reserved.

  16. Decision support system for use in smart wells for the development of oil reservoirs; Sistema de apoio a decisao para uso de pocos inteligentes no desenvolvimento de reservatorios de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Almeida, Luciana Faletti [Centro Federal de Educacao Tecnologica Celso Suckow da Fonseca (CEFET-RJ), Rio de Janeiro, RJ (Brazil)], e-mail: faletti@ele.puc-rio.br; Pacheco, Marco Aurelio Cavalcanti; Vellasco, Marley Maria Bernardes Rebuzzi; Tupac Valdivia, Yvan Jesus; Lazo, Juan Guillermo [Pontificia Univ. Catolica do Rio de Janeiro (PUC/Rio), RJ (Brazil)], e-mail: marco@ele.puc-rio.br, e-mail: marley@ele.puc-rio.br, e-mail: yvantv@ele.puc-rio.br, e-mail: juan@ele.puc-rio.br

    2008-06-15

    Reservoir management is an essential task aimed at the challenge of optimizing the exploration of petroliferous reservoirs. In response to such a challenge, the oil and gas industry has been developing new technologies, such as intelligent wells. These wells are intended to reduce the costs of the more commonplace restoring operations by controlling their technology. This work studies the development of intelligent fields and introduces a decision taking support system able to optimize, through evolutionary algorithms, the intelligent well technology control process considering the technical uncertainties: in valves and geological failures. Moreover, the system proposes to support decision taking, to use or not intelligent wells, given a reservoir ready to be explored or to receive expansion investments. The optimization seeks a strategy of pro-active control, in other words, act before the effect, seeking in the initial production times a configuration of valves capable of: delaying the arrival of the water cut of the production wells, accelerate the oil production or to improve the oil recovery. As a result, an operation that maximizes the NPV (Net present value). The model was tested in three reservoirs, the first being a synthetic reservoir, and the others with more realistic characteristics. (author)

  17. Assessment of undiscovered oil and gas resources in the Ventura Basin Province, California, 2016

    Science.gov (United States)

    Tennyson, Marilyn E.; Schenk, Christopher J.; Pitman, Janet K.; Lillis, Paul G.; Klett, Timothy R.; Brownfield, Michael E.; Finn, Thomas M.; Gaswirth, Stephanie B.; Hawkins, Sarah J.; Marra, Kristen R.; Mercier, Tracey J.; Le, Phuong A.; Leathers-Miller, Heidi M.

    2017-10-02

    The U.S. Geological Survey (USGS) completed a geology-based assessment of undiscovered, technically recoverable conventional and continuous oil and gas resources in the part of the Ventura Basin Province that lies onshore or within State waters (within 3 miles of the shoreline) of California (fig. 1). Conventional oil and gas resources are those that have migrated upward into structural or stratigraphic traps from deep zones where the oil and gas is generated; water is present below the oil or gas. Continuous accumulations, in contrast, are those in which oil or gas is pervasively present in essentially all wells that penetrate them, that may not be structurally or stratigraphically trapped, and that typically lack oil-water or gas-water contacts. They are commonly produced with well-stimulation technology, such as hydraulic fracturing, referred to as “unconventional.” The same stimulation technology, however, is also used in many conventionally trapped accumulations. We estimated both the likely range of oil and gas volumes remaining to be discovered in accumulations similar to existing conventional oil and gas fields in the Ventura Basin Province (previously assessed by Keller [1995] as 1,060 million barrels of oil [MMBO], 1,900 billion cubic feet of gas [BCFG], and 60 million barrels of natural gas liquids [MMBNGL]), and the potential for oil and gas that might be present in a continuous accumulation at extreme depth in the floor of the basin.

  18. Low-threshold stimulated emission at 249 nm and 256 nm from AlGaN-based multiple-quantum-well lasers grown on sapphire substrates

    Energy Technology Data Exchange (ETDEWEB)

    Li, Xiao-Hang; Detchprohm, Theeradetch; Kao, Tsung-Ting; Satter, Md. Mahbub; Shen, Shyh-Chiang; Douglas Yoder, P.; Dupuis, Russell D., E-mail: dupuis@gatech.edu [Center for Compound Semiconductors and School of Electrical and Computer Engineering, Georgia Institute of Technology, Atlanta, Georgia 30332-0250 (United States); Wang, Shuo; Wei, Yong O.; Xie, Hongen; Fischer, Alec M.; Ponce, Fernando A. [Department of Physics, Arizona State University, Tempe, Arizona 85287-1504 (United States); Wernicke, Tim; Reich, Christoph; Martens, Martin; Kneissl, Michael [Technical University of Berlin, Institute for Solid State Physics, Berlin D-10623 (Germany)

    2014-10-06

    Optically pumped deep-ultraviolet (DUV) lasing with low threshold was demonstrated from AlGaN-based multiple-quantum-well (MQW) heterostructures grown on sapphire substrates. The epitaxial layers were grown pseudomorphically by metalorganic chemical vapor deposition on (0001) sapphire substrates. Stimulated emission was observed at wavelengths of 256 nm and 249 nm with thresholds of 61 kW/cm{sup 2} and 95 kW/cm{sup 2} at room temperature, respectively. The thresholds are comparable to the reported state-of-the-art AlGaN-based MQW DUV lasers grown on bulk AlN substrates emitting at 266 nm. These low thresholds are attributed to the optimization of active region and waveguide layer as well as the use of high-quality AlN/sapphire templates. The stimulated emission above threshold was dominated by transverse-electric polarization. This work demonstrates the potential candidacy of sapphire substrates for DUV diode lasers.

  19. Low-threshold stimulated emission at 249 nm and 256 nm from AlGaN-based multiple-quantum-well lasers grown on sapphire substrates

    International Nuclear Information System (INIS)

    Li, Xiao-Hang; Detchprohm, Theeradetch; Kao, Tsung-Ting; Satter, Md. Mahbub; Shen, Shyh-Chiang; Douglas Yoder, P.; Dupuis, Russell D.; Wang, Shuo; Wei, Yong O.; Xie, Hongen; Fischer, Alec M.; Ponce, Fernando A.; Wernicke, Tim; Reich, Christoph; Martens, Martin; Kneissl, Michael

    2014-01-01

    Optically pumped deep-ultraviolet (DUV) lasing with low threshold was demonstrated from AlGaN-based multiple-quantum-well (MQW) heterostructures grown on sapphire substrates. The epitaxial layers were grown pseudomorphically by metalorganic chemical vapor deposition on (0001) sapphire substrates. Stimulated emission was observed at wavelengths of 256 nm and 249 nm with thresholds of 61 kW/cm 2 and 95 kW/cm 2 at room temperature, respectively. The thresholds are comparable to the reported state-of-the-art AlGaN-based MQW DUV lasers grown on bulk AlN substrates emitting at 266 nm. These low thresholds are attributed to the optimization of active region and waveguide layer as well as the use of high-quality AlN/sapphire templates. The stimulated emission above threshold was dominated by transverse-electric polarization. This work demonstrates the potential candidacy of sapphire substrates for DUV diode lasers.

  20. Increasing Waterflood Reserves in the Wilmington Oil Field through Improved Reservoir Characterization and Reservoir Management

    Energy Technology Data Exchange (ETDEWEB)

    Clarke, D.; Koerner, R.; Moos D.; Nguyen, J.; Phillips, C.; Tagbor, K.; Walker, S.

    1999-04-05

    This project used advanced reservoir characterization tools, including the pulsed acoustic cased-hole logging tool, geologic three-dimensional (3-D) modeling software, and commercially available reservoir management software to identify sands with remaining high oil saturation following waterflood. Production from the identified high oil saturated sands was stimulated by recompleting existing production and injection wells in these sands using conventional means as well as a short radius redrill candidate.

  1. Electricity/oil substitution

    International Nuclear Information System (INIS)

    Melvin, J.G.

    1980-09-01

    The extent to which electricity could substitute for imported oil in Canada is assessed and it is concluded that the bulk of projected oil imports could be displaced. This substitution of electricity for oil could be largely completed within two decades, with existing technology, using Canadian resources. The substitution of electricity for imported oil would result in relatively low energy costs and would stimulate economic growth. Energy self-sufficiency through the substitution of electricity for oil is uniquely a Canadian option; it is not open to other industrial countries. The option exists because of Canada's resources of oil sands for essential liquid fuels, hydraulic and nuclear electrical potential, and natural gas as an interim source of energy. While other countries face an energy crisis due to declining supplies of oil, Canada faces opportunities. The policies of Federal and Provincial governments, as perceived by individual decision makers, will have a major influence on Canada's ability to realize opportunities. (auth)

  2. Optimization of production in the oil field through the study of the problem of location of wells and production units; Otimizacao da producao em campo de petroleo pelo estudo do problema de localizacao de pocos e unidades de producao

    Energy Technology Data Exchange (ETDEWEB)

    Santana, Roberta G.S. [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil); Rosa, Vinicius R. [Petroleo Brasileiro S.A. (PETROBRAS), Rio de Janeiro, RJ (Brazil)

    2012-07-01

    This project provides a process for determining the best location of well and production units in an oil field in order to optimize the reservoir performance and the volume of recovered oil, maximizing the profitability. The process uses various statistical analyses presented in the reservoir simulation results, under considerations and parameters. Sensibility analysis and response surface methodology is also applied to a better understanding of how each well influence the total production and the location of the platform and/or manifold can be changed to optimize the production. The method is shown being applied on a field scale with synthetic data. It aims to be a new way of guiding decision-making on a project to develop a field production. (author)

  3. EOR by stimulated microflora

    Energy Technology Data Exchange (ETDEWEB)

    Svarovskaya, L.I.; Altunina, L.K.; Rozhenkova, Z.A.; Bulavin, V.D. [Institute of Petroleum Chemistry, Tomsk (Russian Federation)

    1995-12-31

    A combined microbiological and physico-chemical method for EOR has been developed for flooded West Siberia oil fields with formation temperature of 45{degrees}-95{degrees}C (318-365K). Formation water includes rich and various biocenoses numbering up to 2 x 10{sup 7} cells per ml. Representatives of genera, i.e, Pseudomonas, Bacillus, Actinomyces, Micrococcus, Mycobacterium, Sarcina, etc. were found to be the most widely distributed microorganisms. The method is based on injection of systems exhibiting high oil displacing capacity and at the same time being an additional nitrous nutrient for endemic populations of microorganisms. Their injection into formation water favors biomass growth by 4-6 orders and promotes syntheses of biosurfactants, biopolymers, acids, etc., and gaseous products. The features of residual oil displacement have been studied on laboratory models using a combined microbiological and physico-chemical method. A curve for the yield of residual oil is presented by two peaks. The first peak is stipulated by the washing action of oil displacement system, and the second one by the effect of metabolites produced at stimulation of biogenic processes. Oil displacement index increases by 15%-30%.

  4. Polycyclic aromatic hydrocarbons (PAH), nickel and vanadium in air dust from Bahrein (Persian Gulf): Measurements and Puff model calculations for this area during the burning of the oil wells in Kuwait

    International Nuclear Information System (INIS)

    Vaessen, H.A.M.G.; Wilbers, A.A.M.M.; Jekel, A.A.; Van Pul, W.A.J.; Van der Meulen, A.; Bloemen, H.J.Th.; De Boer, J.L.M.

    1993-01-01

    When Kuwait's oil wells were at fire in 1991, air particulate matter (inhalable fraction) was sampled in Bahrain (soot clouds were over that region at that time) and analysed for PAHs, nickel (Ni) and vanadium (V). Also in that period Puff-model calculations were carried out to forecast the dispersion of the combustion products and the impact on the environment in the Persian Gulf region. Based on the outcome of the model calculations and the analytical findings the major conclusions are that: (a) the PAH contamination level of the air particulate matter is equal or below that found for rural areas in the Netherlands and on average one order of magnitude below the findings of the model calculations; (b) there is no link between the air particulate matter content and the PAH contamination measured. The benzo(a)pyrene fraction of the PAH contamination is 10-14% which is surprisingly constant; (c) the strongly significant correlation between the Ni- and V-content both mutually and with respect to the air particulate matter content strongly suggests a common origin i.e. the burning oil wells in Kuwait; (d) the air particulate matter content measured is one up to two orders of magnitudes over the findings of the model calculations; (e) the emission factors applied in the Puff-model calculations, most probably, insufficiently match the combustion conditions of oil wells at fire. 6 figs., 3 tabs.,

  5. Risks resulting from using rules-of-thumb when cementing oil wells; Riscos decorrentes do uso de chavoes nas cimentacoes de pocos de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Maria das Gracas Pena; Miranda, Cristiane Richard de [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas. Superintendencia de Pesquisa de Exploracao e Producao

    1994-07-01

    In the oil industry the two most popular rules-of-thumb related to interpreting the thickening time tests are: 'On reaching 50 Uc (consistency units) the cement slurries are no longer pumpable' and 'Time spent on mixing and displacing the slurries should not exceed 60% of the thickening time'. To check these rules more then 200 experimental tests were carried out which show that depending on the additives used, the consistometry curves may require individual interpretation and slurries with different composition have great changes of showing different apparent viscosities even when having the same consistency. (author)

  6. Effects of Thyme Extract Oils (from Thymus vulgaris, Thymus zygis, and Thymus hyemalis on Cytokine Production and Gene Expression of oxLDL-Stimulated THP-1-Macrophages

    Directory of Open Access Journals (Sweden)

    A. Ocaña

    2012-01-01

    Full Text Available Properties of thyme extracts from three different species (Thymus vulgaris, Thymus zygis, and Thymus hyemalis were examined. Two oil fractions from each species were obtained by CO2 supercritical fluid extraction. Main compounds presented in the supercritical extracts of the three thyme varieties were 1,8 cineole, thymol, camphor, borneol, and carvacrol. As a cellular model of inflammation/atherogenesis, we use human macrophages derived from THP-1 monocytes and activated by oxidized LDLs. These cells were incubated with the thyme fraction oils, and the productions and gene expressions of the inflammatory mediators TNF-α, IL-1B, IL-6, and IL-10 were determined. Thyme extracts significantly reduced production and gene expression of the proinflammatory mediators TNF-α, IL-1B, and IL-6 and highly increased these parameters on the anti-inflammatory IL-10 cytokine. Changes on production and gene expressions were dose dependent and according to the thyme content of each species. Taken together, these results may suggest that thyme extracts could have anti-inflammatory effects.

  7. Solar Thermal Enhanced Oil Recovery, (STEOR) Volume 1: Executive summary

    Science.gov (United States)

    Elzinga, E.; Arnold, C.; Allen, D.; Garman, R.; Joy, P.; Mitchell, P.; Shaw, H.

    1980-11-01

    Thermal enhanced oil recovery is widely used in California to aid in the production of heavy oils. Steam injection either to stimulate individual wells or to drive oil to the producing wells, is by far the major thermal process today and has been in use for over 20 years. Since steam generation at the necessary pressures (generally below 4000 kPa (580 psia)) is within the capabilities of present day solar technology, it is logical to consider the possibilities of solar thermal enhanced oil recovery (STEOR). The present project consisted of an evaluation of STEOR. Program objectives, system selection, trade-off studies, preliminary design, cost estimate, development plan, and market and economic analysis are summarized.

  8. Laboratory studies of oil spill bioremediation; toward understanding field behavior

    International Nuclear Information System (INIS)

    Prince, R.C.; Hinton, S.M.; Elmendorf, D.L.; Lute, J.R.; Grossman, M.J.; Robbins, W.K.; Hsu, Chang S.; Richard, B.E.; Haith, C.E.; Senius, J.D.; Minak-Bernero, V.; Chianelli, R.R.; Bragg, J.R.; Douglas, G.S.

    1993-01-01

    Oil spill remediation aims to enhance the natural process of microbial hydrocarbon biodegradation. The microbial foundations have been studied throughout this century, but the focus of most of this work has been on the degradation of well defined compounds by well defined microbial species. This paper addresses laboratory studies on crude oil biodegradation by microbial consortia obtained from oiled beaches in Prince William Sound, Alaska following the spill from the Exxon Valdez. It demonstrates that oil degradation is indeed likely to be nitrogen-limited in Prince William Sound, the different molecular classes in crude oil that are subjected to biodegradation, the identification of conserved species in the oil that can be used for assessing biodegradation and bioremediation in the field, the effectiveness of fertilizers in stimulating sub-surface biodegradation, the role of the olephilic fertilizer Inipol EAP22, and the identification of the oil-degrading microorganisms in Prince William Sound. Together, these laboratory studies provided guidance and important insights into the microbial phenomena underlying the successful bioremediation of the oiled shorelines

  9. Oil & Natural Gas Technology A new approach to understanding the occurrence and volume of natural gas hydrate in the northern Gulf of Mexico using petroleum industry well logs

    Energy Technology Data Exchange (ETDEWEB)

    Cook, Ann [The Ohio State Univ., Columbus, OH (United States); Majumdar, Urmi [The Ohio State Univ., Columbus, OH (United States)

    2016-03-31

    The northern Gulf of Mexico has been the target for the petroleum industry for exploration of conventional energy resource for decades. We have used the rich existing petroleum industry well logs to find the occurrences of natural gas hydrate in the northern Gulf of Mexico. We have identified 798 wells with well log data within the gas hydrate stability zone. Out of those 798 wells, we have found evidence of gas hydrate in well logs in 124 wells (15% of wells). We have built a dataset of gas hydrate providing information such as location, interval of hydrate occurrence (if any) and the overall quality of probable gas hydrate. Our dataset provides a wide, new perspective on the overall distribution of gas hydrate in the northern Gulf of Mexico and will be the key to future gas hydrate research and prospecting in the area.

  10. Determination of mechanical damage from wells under oil and gas flow condition; Determinacao de dano mecanico em pocos sob condicao de escoamento de oleo e gas

    Energy Technology Data Exchange (ETDEWEB)

    Marques, J. B.D. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil); Trevisan, O. V. [Universidade Estadual de Campinas (UNICAMP), SP (Brazil)

    2008-07-01

    The well bore effect is one of the most difficult variables obtained from well test analysis under two-phase condition. The presence of the gas in a well inserted in reservoir, which operates under gas drive solution, hinders the development of the analytical model to determine the mechanical damage. It is one of the reasons of the using the single phase well test analysis methodologies become suitable to the multiphase cases. The determination of the well bore effect is justified; therefore it is possible to work over in the well in order to determinate the real potential productive. The main objective of this work is to reevaluate a method of determination of the mechanical damage gotten from a well test under two-phase condition. In this work a simplified model of reservoir simulation is constructed in a commercial simulator in order to validate the methodology. The refinement of the blocks near to the well adopted in the simulation is a good representation of the well mechanical damage which occurs in a homogeneous reservoir. The types of well test analysis used in this work are two: drawdown and buildup test. The results gotten for this methodology, as will be shown, are excellent quality and the model of simulation presented here can be used for other analytical methods studies in order to determinate the mechanical damage or other variable of the reservoir. (author)

  11. The glucagon-like peptide 1 analogue Exendin-4 attenuates the nicotine-induced locomotor stimulation, accumbal dopamine release, conditioned place preference as well as the expression of locomotor sensitization in mice.

    Directory of Open Access Journals (Sweden)

    Emil Egecioglu

    Full Text Available The gastrointestinal peptide glucagon-like peptide 1 (GLP-1 is known to regulate consummatory behavior and is released in response to nutrient ingestion. Analogues of this peptide recently emerged as novel pharmacotherapies for treatment of type II diabetes since they reduce gastric emptying, glucagon secretion as well as enhance glucose-dependent insulin secretion. The findings that GLP-1 targets reward related areas including mesolimbic dopamine areas indicate that the physiological role of GLP-1 extends beyond food intake and glucose homeostasis control to include reward regulation. The present series of experiments was therefore designed to investigate the effects of the GLP-1 receptor agonist, Exendin-4 (Ex4, on established nicotine-induced effects on the mesolimbic dopamine system in mice. Specifically, we show that treatment with Ex4, at a dose with no effect per se, attenuate nicotine-induced locomotor stimulation, accumbal dopamine release as well as the expression of conditioned place preference in mice. In accordance, Ex4 also blocks nicotine-induced expression of locomotor sensitization in mice. Given that development of nicotine addiction largely depends on the effects of nicotine on the mesolimbic dopamine system these findings indicate that the GLP-1 receptor may be a potential target for the development of novel treatment strategies for nicotine cessations in humans.

  12. Surrogate reservoir models for CSI well probabilistic production forecast

    Directory of Open Access Journals (Sweden)

    Saúl Buitrago

    2017-09-01

    Full Text Available The aim of this work is to present the construction and use of Surrogate Reservoir Models capable of accurately predicting cumulative oil production for every well stimulated with cyclic steam injection at any given time in a heavy oil reservoir in Mexico considering uncertain variables. The central composite experimental design technique was selected to capture the maximum amount of information from the model response with a minimum number of reservoir models simulations. Four input uncertain variables (the dead oil viscosity with temperature, the reservoir pressure, the reservoir permeability and oil sand thickness hydraulically connected to the well were selected as the ones with more impact on the initial hot oil production rate according to an analytical production prediction model. Twenty five runs were designed and performed with the STARS simulator for each well type on the reservoir model. The results show that the use of Surrogate Reservoir Models is a fast viable alternative to perform probabilistic production forecasting of the reservoir.

  13. Vegetable oil spills : oil properties and behaviour

    International Nuclear Information System (INIS)

    Fingas, M.; Fieldhouse, B.; Jokuty, P.

    2001-01-01

    In 1997, the United States Environmental Protection Agency conducted a thorough review of the issue regarding vegetable oil spills. Recent attention has refocused on this issue as a result of an incident where 20 tons of canola oil was spilled in the Vancouver Harbour in 2000. In the past, vegetable oils were suggested to be a useful test material because they were thought to be innocuous. It was even suggested they be used to remove petroleum oil residues from beaches. However, recent studies have shown that spills of vegetable oils can have major environmental consequences, equivalent to those of petroleum oil spills. The spills have devastating effects on birds and intertidal organisms. This paper presented a summary of historical vegetable spills from around the world. In this study, specific behaviour tests were examined for several oils including canola, soy bean, olive, castor and corn oils. Evaporation, water-in-oil emulsification and chemical dispersion were measured and were found to be nearly zero, suggesting that vegetable oil spills are not very soluble in water. The aquatic toxicity of vegetable oil is low, but their fate is quite different from petroleum. Vegetable oils do not evaporate to a significant degree, they do not form water-in-oil emulsions, nor do they disperse in water. The physical properties of vegetable oils were also measured, including density and viscosity. This paper presented the aquatic toxicity of several vegetable oils along with other environmental data including the degradation rates noted in the literature. Most environmental damage reported in the literature is by contact with birds feathers resulting in hypothermia and secondly by smothering of intertidal organisms. The effect of vegetable oil on fish has not been well studied, but it is expected that there will be little destructive effect except where smothering can occur. 35 refs., 3 tabs

  14. Vegetable oil spills : oil properties and behaviour

    Energy Technology Data Exchange (ETDEWEB)

    Fingas, M.; Fieldhouse, B.; Jokuty, P. [Environment Canada, Ottawa, ON (Canada). Emergencies Science Div

    2001-07-01

    In 1997, the United States Environmental Protection Agency conducted a thorough review of the issue regarding vegetable oil spills. Recent attention has refocused on this issue as a result of an incident where 20 tons of canola oil was spilled in the Vancouver Harbour in 2000. In the past, vegetable oils were suggested to be a useful test material because they were thought to be innocuous. It was even suggested they be used to remove petroleum oil residues from beaches. However, recent studies have shown that spills of vegetable oils can have major environmental consequences, equivalent to those of petroleum oil spills. The spills have devastating effects on birds and intertidal organisms. This paper presented a summary of historical vegetable spills from around the world. In this study, specific behaviour tests were examined for several oils including canola, soy bean, olive, castor and corn oils. Evaporation, water-in-oil emulsification and chemical dispersion were measured and were found to be nearly zero, suggesting that vegetable oil spills are not very soluble in water. The aquatic toxicity of vegetable oil is low, but their fate is quite different from petroleum. Vegetable oils do not evaporate to a significant degree, they do not form water-in-oil emulsions, nor do they disperse in water. The physical properties of vegetable oils were also measured, including density and viscosity. This paper presented the aquatic toxicity of several vegetable oils along with other environmental data including the degradation rates noted in the literature. Most environmental damage reported in the literature is by contact with birds feathers resulting in hypothermia and secondly by smothering of intertidal organisms. The effect of vegetable oil on fish has not been well studied, but it is expected that there will be little destructive effect except where smothering can occur. 35 refs., 3 tabs.

  15. Influence of physical and chemical dispersion on the biodegradation of oil under simulated marine conditions

    International Nuclear Information System (INIS)

    Swannell, R. P. J.; Daniel, F.; Croft, B. C.; Engelhardt, M. A.; Wilson, S.; Mitchell, D. J.; Lunel, T.

    1997-01-01

    Dispersion and biodegradation of oil was studied in marine microcosms designed to simulate oil dispersion at sea. Dispersion was studied using both Phase Doppler Particle Analyser and a Chamber Slide technique. In both natural and artificial seawater, oil addition was observed to encourage the growth of hydrocarbon-degrading bacteria in the presence of sufficient nitrogen and phosphorus. Results showed that microorganisms enhanced oil dispersion by colonizing physically-dispersed oil droplets and preventing re-coalescence with the surface slick. The addition of dispersants increased the rate of colonization as well as the number of degraded droplets. These results suggest that stimulation of physical dispersion by chemical means increase the rate of oil biodegradation under natural conditions. 25 refs., 3 tabs., 14 figs

  16. New technology for sulfide reductions and increased oil recovery: Petroleum project fact sheet

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-12-14

    This Fact Sheet is written for the Inventions and Innovations Program about a new technology for sulfide reduction and increased oil recovery. The new technology, called Bio-Competitive Exclusion (BCX), results in greater oil production and prevents the production of corrosive hydrogen sulfide in oil and gas reservoirs. This BCX process is initiated and maintained by a new product, called Max-Well 2000, in which nutrients are custom designed to stimulate targeted beneficial microorganisms that live in every oil and gas reservoir. Rapid growth of these microorganisms excludes activity of harmful sulfide-producing bacteria and produces by-products that serve as effective tertiary oil recovery agents and as sulfide degradation agents. Oil and gas production is both increased and sweetened.

  17. Well-resolved oil-soluble Au-doped ZnCdS quantum dots and enhancing doping emission with In-codoping

    Energy Technology Data Exchange (ETDEWEB)

    Zeng, Ruosheng, E-mail: zengrsh@gznu.edu.cn [School of Life and Environmental Sciences, Guilin University of Electronic Technology, Guilin 541004 (China); School of Chemistry and Materials Science, Guizhou Normal University, Guiyang 550001 (China); Sun, Zhiguo [School of Chemistry and Materials Science, Guizhou Normal University, Guiyang 550001 (China); Zhou, Chunjiao [College of Science, Hunan Agricultural University, Changsha 410128 (China); Fang, Cheng; Han, Guo-Cheng [School of Life and Environmental Sciences, Guilin University of Electronic Technology, Guilin 541004 (China); Chen, Zhencheng, E-mail: chenzhcheng@guet.edu.cn [School of Life and Environmental Sciences, Guilin University of Electronic Technology, Guilin 541004 (China)

    2016-06-25

    Highly emissive semiconductor quantum dots (QDs) with tunable color are valuable in many applications such as solid state lighting and bio-imaging. Herein, we report a facile synthetic method to Au:ZnCdS and Au:ZnCdS/ZnS core/shell QDs with tunable emission color. The highly active Au precursor (HAuCl{sub 4}) is prevented to be decomposed at high reaction temperature using 1-dodecanethiol (DDT) as the surface ligand. High-quality Au:ZnCdS/ZnS core/shell QDs are prepared and the highest photoluminescence (PL) quantum yield (QY) can achieve 42% by overcoating of ZnS layer over the bare Au:ZnCdS core QDs. Furthermore, through using Au{sup +} ion as the primary dopants and trivalent cation In{sup 3+} as co-dopants, the PL QY can be enhanced significantly because compensation of In{sup 3+} ion-codoping for the charge imbalance from Au{sup +}-doping. This codoping strategy may be applied to other related optical materials to control the optical properties based on our understanding for physical mechanism. - Highlights: • High-quality oil-soluble Au:ZnCdS/ZnS QDs were prepared for the first time. • The highly active HAuCl4 is prevented to decompose by using 1-dodecanethiol. • The highest PL QY of Au:ZnCdS/ZnS QDs can achieve 42% by overcoating ZnS layer. • The PL QY of QDs can be significantly enhanced by Au{sup +}, In{sup 3+}-codoping.

  18. Theoretical modeling for optimizing horizontal production well placement in thermal recovery environments to maximize recovery

    Energy Technology Data Exchange (ETDEWEB)

    Bourgeois, D.J. [Schlumberger Canada Ltd., Calgary, AB (Canada)

    2008-07-01

    Heavy oil has a high viscosity and a low API gravity rating. Since it is difficult to get a fluid of this nature to flow, enhanced oil recovery techniques are required to extract the oil from the reservoir. Thermal recovery strategies such as steam assisted gravity drainage (SAGD) and cyclic steam injection stimulation (CSS) can be used. These techniques involve injecting steam into a formation which heats up the fluid in place decreasing its viscosity and allowing it to flow into the producing well bore. In order to maximize hydrocarbon recovery from this type of geological environment, the placement of the horizontal production well bore relative to the base of the reservoir is important. In conventional oil and gas plays, well placement methods involving directional deep resistivity logging while drilling (DDR-LWD) measurements to map formation contacts while drilling have enabled wells to be placed relative to formation boundaries. This paper discussed a study that presented some theoretical resistivity inversion and forward modeling results generated from a three-dimensional geocellular model to confirm that this evolving DDR-LWD technology may be applicable to western Canada's Athabasca heavy oil drilling environments. The paper discussed the effect of well bore position, thermal recovery, and pro-active well placement. Resistivity modeling work flow was also presented. It was concluded that being able to drill a horizontal production well relative to the base of the formation could help minimize abandoned oil ultimately leading to better recovery. 4 refs., 8 figs.

  19. Comparison between genetic fuzzy system and neuro fuzzy system to select oil wells for hydraulic fracturing; Comparacao entre genetic fuzzy system e neuro fuzzy system para selecao de pocos de petroleo para fraturamento hidraulico

    Energy Technology Data Exchange (ETDEWEB)

    Castro, Antonio Orestes de Salvo [PETROBRAS, Rio de Janeiro, RJ (Brazil); Ferreira Filho, Virgilio Jose Martins [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil)

    2004-07-01

    The hydraulic fracture operation is wide used to increase the oil wells production and to reduce formation damage. Reservoir studies and engineer analysis are made to select the wells for this kind of operation. As the reservoir parameters have some diffuses characteristics, Fuzzy Inference Systems (SIF) have been tested for this selection processes in the last few years. This paper compares the performance of a neuro fuzzy system and a genetic fuzzy system used for hydraulic Fracture well selection, with knowledge acquisition from an operational data base to set the SIF membership functions. The training data and the validation data used were the same for both systems. We concluded that, in despite of the genetic fuzzy system would be a younger process, it got better results than the neuro fuzzy system. Another conclusion was that, as the genetic fuzzy system can work with constraints, the membership functions setting kept the consistency of variables linguistic values. (author)

  20. Geopressured-geothermal drilling and testing plan. General Crude Oil--Dept. of Energy Pleasant Bayou No. 1 well, Brazoria County, Texas

    Energy Technology Data Exchange (ETDEWEB)

    1978-05-01

    As a result of geopressured resource assessment studies in the Gulf Coast region, the Brazoria fairway, located in Brazoria County, Texas was determined to be an optimum area for additional studies. A plan is presented for drilling, completion, and testing of one geopressured-geothermal well and two disposal wells in Brazoria County, Texas. The objectives of the well drilling and testing program are to determine the following parameters: reservoir permeability, porosity, thickness, rock material properties, depth, temperature, and pressure; reservoir fluid content, specific gravity, resistivity, viscosity, and hydrocarbons in solution; reservoir fluid production rates, pressure, temperature, production decline, and pressure decline; geopressured well and surface equipment design requirements for high-volume production and possible sand production; specific equipment design for surface operations, hydrocarbons distribution, and effluent disposal; and possibilities of reservoir compaction and/or surface subsidence. (JGB)

  1. A new cement slurry modified with chitosan/alginate interpenetrating networks and hydroxyapatite: structural characteristics after long-term contact with hyper-saline produced water from oil well operations

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Ivory Marcos Gomes dos; Santos, Danilo Oliveira; Cestari, Antonio Reinaldo, E-mail: ivorymarcos@hotmail.com, E-mail: danilo.quimico@yahoo.com.br, E-mail: rcestari@gmail.com [Universidade Federal de Sergipe (UFS), Sao Cristovao, SE (Brazil). Departamento de Ciencia dos Materiais; Ribeiro, Joenesson Filip Santos, E-mail: joenesson.joe@hotmail.com [Universidade Federal de Sergipe (UFS), Sao Cristovao, SE (Brazil). Lab, Materiais e Calorimetria; Alves, Jose do Patrocinio Hora; Ferreira, Angelica Baganha, E-mail: jphalves@uol.com.br, E-mail: angelica.bferreira@itps.se.gov.br [Instituto Tecnologico e de Pesquisas do Estado de Sergipe (ITPS), Aracaju, SE (Brazil)

    2017-01-15

    Oil is an important source of energy, mainly in developing countries. Important research has been conducted to find cementing procedures that guarantee safe and cost-effective oil exploration below pre-salt layers. This work aimed to make a new cement paste with cement, seawater, silica, biopolymers (chitosan and sodium alginate) and hydroxyapatite (HA), found in nature. For comparison purposes, slurry without additives was prepared and characterized. The HA used was extracted from fish scales (Cynoscion acoupa) in optimized condition NaOH concentration, temperature and reaction time. Both slurry were prepared with ratios water/cement (w/c) and silica/cement (s/c) equal to 0.50 and 0.35, respectively. The new cement slurry was obtained with proportions of 5% of each biopolymer and HA with respect to the total weight of the cement. In the immersion tests, specimens were immersed in samples of hyper production of saline water by 35°C for 15 days. Thereafter, they were washed, dried and its surface layers were scraped. Before, the resulting materials were characterized. The values of the ratios Ca/Si of new cement slurry (3.38 ± 0.06) were superior compared to standard (2.58 ± 0.05). The new slurry had high thermal stability and low amounts of small crystallite-type portlandite (35.70 nm). Conversely, a slurry standard formed larger crystals of about 50.3 nm. Significantly, after continuous long-term contact of both slurries with hyper-saline produced water from oil well fields operations, in comparison with standard slurry structural characteristics, the new slurry has practically maintained its pristine chemical structure, as well as has shown crystallite-type particles of NaCl and Friedel’s/Kuzel’s salts with lower proportion. The presence of the biopolymers and HA has driven the improved the self-healing properties observed in the new cement slurry. In this first study, the new slurry has shown adequate characteristics to contribute to cost effective and

  2. A new cement slurry modified with chitosan/alginate interpenetrating networks and hydroxyapatite: structural characteristics after long-term contact with hyper-saline produced water from oil well operations

    International Nuclear Information System (INIS)

    Santos, Ivory Marcos Gomes dos; Santos, Danilo Oliveira; Cestari, Antonio Reinaldo

    2017-01-01

    Oil is an important source of energy, mainly in developing countries. Important research has been conducted to find cementing procedures that guarantee safe and cost-effective oil exploration below pre-salt layers. This work aimed to make a new cement paste with cement, seawater, silica, biopolymers (chitosan and sodium alginate) and hydroxyapatite (HA), found in nature. For comparison purposes, slurry without additives was prepared and characterized. The HA used was extracted from fish scales (Cynoscion acoupa) in optimized condition NaOH concentration, temperature and reaction time. Both slurry were prepared with ratios water/cement (w/c) and silica/cement (s/c) equal to 0.50 and 0.35, respectively. The new cement slurry was obtained with proportions of 5% of each biopolymer and HA with respect to the total weight of the cement. In the immersion tests, specimens were immersed in samples of hyper production of saline water by 35°C for 15 days. Thereafter, they were washed, dried and its surface layers were scraped. Before, the resulting materials were characterized. The values of the ratios Ca/Si of new cement slurry (3.38 ± 0.06) were superior compared to standard (2.58 ± 0.05). The new slurry had high thermal stability and low amounts of small crystallite-type portlandite (35.70 nm). Conversely, a slurry standard formed larger crystals of about 50.3 nm. Significantly, after continuous long-term contact of both slurries with hyper-saline produced water from oil well fields operations, in comparison with standard slurry structural characteristics, the new slurry has practically maintained its pristine chemical structure, as well as has shown crystallite-type particles of NaCl and Friedel’s/Kuzel’s salts with lower proportion. The presence of the biopolymers and HA has driven the improved the self-healing properties observed in the new cement slurry. In this first study, the new slurry has shown adequate characteristics to contribute to cost effective and

  3. Mean-field dynamics of a Bose-Einstein condensate in a time-dependent triple-well trap: Nonlinear eigenstates, Landau-Zener models, and stimulated Raman adiabatic passage

    International Nuclear Information System (INIS)

    Graefe, E. M.; Korsch, H. J.; Witthaut, D.

    2006-01-01

    We investigate the dynamics of a Bose-Einstein condensate in a triple-well trap in a three-level approximation. The interatomic interactions are taken into account in a mean-field approximation (Gross-Pitaevskii equation), leading to a nonlinear three-level model. Additional eigenstates emerge due to the nonlinearity, depending on the system parameters. Adiabaticity breaks down if such a nonlinear eigenstate disappears when the parameters are varied. The dynamical implications of this loss of adiabaticity are analyzed for two important special cases: A three-level Landau-Zener model and the stimulated Raman adiabatic passage (STIRAP) scheme. We discuss the emergence of looped levels for an equal-slope Landau-Zener model. The Zener tunneling probability does not tend to zero in the adiabatic limit and shows pronounced oscillations as a function of the velocity of the parameter variation. Furthermore we generalize the STIRAP scheme for adiabatic coherent population transfer between atomic states to the nonlinear case. It is shown that STIRAP breaks down if the nonlinearity exceeds the detuning

  4. Restimulation of wells using biodegradable particulates as temporary diverting agents

    Energy Technology Data Exchange (ETDEWEB)

    Allison, D.; Curry, S.; Todd, B. [Halliburton (Canada)

    2011-07-01

    Producing wells are generally not exploited to their full capacity; however, they may be restimulated. In cases where restimulation is viable, applying the process to an old well is more cost effective than exploiting a new well. Fracturing stimulation (refrac) is a challenging process that may be achieved by isolating portions of the reservoir in order to focus refrac treatment energy. Isolation is traditionally accomplished via the use of a physical barrier within the reservoir or by introducing diverting agents into the flow stream to divert the treatment. The current study developed a new technology of diverters for the restimulation of reservoirs. The new technology consists of a self-assembled polymer that is robust, biodegradable and cost-effective. Results show that the new organic diverters temporarily isolated perforation in the near-wellbore region, allowing to significantly increase the oil production and the recovered original oil in place (OOIP) from the reservoir.

  5. Attenuated gastric distress but no benefit to performance with adaptation to octanoate-rich esterified oils in well-trained male cyclists

    DEFF Research Database (Denmark)

    Thorburn, M.S.; Vistisen, Bodil; Thorp, R.M.

    2006-01-01

    We investigated the effects of modifying a normal dietary fatty acid composition and ingestion of high-fat exercise supplements on gastrointestinal distress, substrate oxidation. and endurance cycling performance. Nine well-trained male cyclists completed a randomized triple-crossover comprising...

  6. Evaluation of underground water contamination of tubular wells, by fuels oil in Santo Andre City, Sao Paulo state: a contribution to the environmental management

    International Nuclear Information System (INIS)

    Mindrisz, Ana Copat

    2006-01-01

    The contamination of underground waters by hydrocarbons originated from gas stations has been object of increasing preoccupation in environmental organization all over the world. The organic compounds Benzene, Toluene, Ethylbenzene and Xylene (BTEX), present in these fuels, are extremely toxic to human health and could make impracticable the exploration of these contaminated waters by these kinds of pollutants and consequently the gasoline wells used for this purpose. In this work, it was carried out a diagnosis of the water quality with information and analyses, with the goals to snap shot the situation of the wells destined to domestic and commercial supply of water in the urban area of Santo Andre city, Sao Paulo state. There have been evaluated the presence of micron pollutants BTEX, after contamination due to leaks in fuel storage tanks close to the wells, in different places of the city. The physical chemistry parameters like color, turbidity and residual chlorine were also evaluated as well as trace elements, metals, anions like fluorine, sulphates, chlorine, nitrates and phosphates and bacteriological (total coliforms, thermo stable coliforms, heterotrophic bacteria). On definition of the sampling area, it was sought, at first, the evaluation of environmental contaminations historical series by gas stations, evaluating the set of information available at government environmental organizations and spatial representatively of the problem. For administration of the underground water quality it was adopted the methodology used by Companhia de Tecnologia de Saneamento Ambiental (CETESB), being accomplished a previous identification of contaminated potential areas and organizing a data base on landfills disposal and neglected places; registration of gas station services and, wells used by the population, industrial inventory with active and neglected maps taking into consideration the size and residues generation (such as SEMASA), prioritizing in this way the

  7. Emulation and Control of Slugging Flows in a Gas-Lifted Offshore Oil Production Well Through a Lab-sized Facility

    DEFF Research Database (Denmark)

    Jepsen, Kasper Lund; Hansen, Leif; Mai, Christian

    2013-01-01

    flow and pressures in the production well system, which is referred to as the slugging flow problem. This instability is mainly due to the casing-heading mechanism. This work investigates the possibility to use a feedback control for stabilizing the production operation without sacrificing...... the production capability. A labsized production well system is constructed in an economic manner. Afterwards, a simple nonlinear model is derived according to physical principles and then verified with the experimental facility. A observer-based state feedback control is designed to handle the potential...... slugging problem. The developed controller manipulates the openness degree of the production choke based on feedback a number of pressure measurements. The current simulation results showed satisfactory control performances by stabilizing the system operation at some relatively large production rate which...

  8. Final report on Technical Demonstration and Economic Validation of Geothermally-Produced Electricity from Coproduced Water at Existing Oil/Gas Wells in Texas

    Energy Technology Data Exchange (ETDEWEB)

    Luchini, Chris B. [Universal GeoPower LLC, Houston, TX (United States)

    2015-06-01

    The initial geothermal brine flow rate and temperature from the re-worked well were insufficient, after 2.5 days of flow testing, to justify advancing past Phase I of this project. The flow test was terminated less than 4 hours from the Phase I deadline for activity, and as such, additional flow tests of 2+ months may be undertaken in the future, without government support.

  9. Palm Oil

    Science.gov (United States)

    Palm oil is obtained from the fruit of the oil palm tree. Palm oil is used for preventing vitamin A deficiency, cancer, ... blood pressure, high cholesterol, and cyanide poisoning. Palm oil is used for weight loss and increasing the ...

  10. Diesel oil

    Science.gov (United States)

    Oil ... Diesel oil ... Diesel oil poisoning can cause symptoms in many parts of the body. EYES, EARS, NOSE, AND THROAT Loss of ... most dangerous effects of hydrocarbon (such as diesel oil) poisoning are due to inhaling the fumes. NERVOUS ...

  11. growth stimulant

    African Journals Online (AJOL)

    Effects of timing and duration of supplementation of LIVFIT VET ® (growth stimulant) as substitute for fish meal on the growth performance, haematology and clinical enzymes concentration of growing pigs.

  12. Outlook for Saskatchewan heavy oil

    International Nuclear Information System (INIS)

    Youzwa, P.

    1993-01-01

    Some of the opportunities and challenges currently facing the heavy oil industry in Saskatchewan are discussed from a government perspective. By the end of September 1993, 220 heavy oil wells were drilled in the province, and 26% of the land sales in 1993 were in heavy oil areas. About 41% of the wells drilled in heavy oil areas were horizontal oil wells. Of the total horizontal wells drilled in Saskatchewan, 48% are for heavy oil, and horizontal well production averages 85 bbl/d. Initial trends suggest that horizontal wells both accelerate production and contribute to ultimate recovery. Total heavy oil production in 1992 reached 28.9 million bbl and recoverable reserves in 1991 were 262.3 million bbl, or 1.5% of total oil in place. The low recovery is not only due to technical factors such as high viscosity but also to low investment in the heavy oil sector due to poor economics. It is hoped that lower interest and exchange rates, the success of horizontal wells and the provincial royalty structure will maintain the recent increase in heavy oil activity. The provincial government recently launched a comprehensive energy strategy in which development of a heavy oil strategy is an important component. Total heavy oil reserves exceed those of light and medium oil and have significant development potential. The Saskatchewan government wishes to adopt a cooperative and partnership approach in its dealings with the heavy oil industry to help realize this potential. 9 figs

  13. Oil spills

    International Nuclear Information System (INIS)

    Katsouros, M.H.

    1992-01-01

    The world annually transports 1.7 billion tons of oil by sea, and oil spills, often highly concentrated discharges, are increasing from a variety of sources. The author discusses sources of oils spills: natural; marine transportation; offshore oil production; atmospheric sources; municipal industrial wastes and runoff. Other topics include: the fate of the spilled oil; the effects of the oil; the response to oil spills; and prevention of oil spills. 30 refs., 1 fig., 4 tabs

  14. Energy return on (energy) invested (EROI), oil prices, and energy transitions

    International Nuclear Information System (INIS)

    Heun, Matthew Kuperus; de Wit, Martin

    2012-01-01

    Very little work has been done so far to model, test, and understand the relationship between oil prices and EROI over time. This paper investigates whether a declining EROI is associated with an increasing oil price and speculates on the implications of these results on oil policy. A model of the relationship between EROI and oil market prices was developed using basic economic and physical assumptions and non-linear least-squares regression models to correlate oil production price with EROI using available data from 1954–1996. The model accurately reflects historical oil prices (1954–1996), and it correlates well with historical oil prices (1997–2010) if a linear extrapolation of EROI decline is assumed. As EROI declines below 10, highly non-linear oil price movements are observed. Increasing physical oil scarcity is already providing market signals that would stimulate a transition away from oil toward alternative energy sources. But, price signals of physical oil scarcity are not sufficient to guarantee smooth transitions to alternative fuel sources, especially when there is insufficient oil extraction technology development, a declining mark-up ratio, a non-linear EROI–cost of production relationship, and a non-linear EROI–price relationship. - Highlights: ► A model of the relationship between EROI and oil prices has been developed. ► As EROI declines below 10, highly non-linear oil price movements are expected. ► Physical oil scarcity provides market signals for a transition to alternatives. ► Scarcity price signals are insufficient for smooth transitions to alternatives.

  15. Parametric analysis of applicability of sand production control in oil wells; Analise parametrica da aplicabilidade do controle de producao de areia em pocos de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Filipe S.B. da; Couto, Paulo [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Curso de Engenharia do Petroleo

    2008-07-01

    The present work discusses about the selection of the best sand control method to be adopted for offshore operations according to a specific technologic limitation and by demands imposed by the environment in which it is used. First of all, the paper mentions the phenomena of solids carrying. Then the source environments of the study are analyzed. This approach is considered important because it is the basis for understanding the final part of the research, composed of the method/environment correlation. Three fictitious offshore fields based on real data are presented. In each of them, two wells are studied, one cased, and one open holed. Parameters like permeability and UCS have the same conceptual relevance as the sand control methods presented. The analysis of methods follows those used for the environments. The following methods are presented: by restriction of solids flow, by drag strength reduction and by increase of cohesion strength. Emphasis is given on mechanic methods. Finally, this study concludes its initial purpose, which is selecting the best sand control method for each well, substantiating in each one, the reason for the choice. (author)

  16. Oil Spills

    Science.gov (United States)

    ... up. How Oil Harms Animals and Plants in Marine Environments In general, oil spills can affect animals and plants in two ways: from the oil ... up. How Oil Harms Animals and Plants in Marine Environments In general, oil spills can affect animals and plants in two ways: from the oil ...

  17. A Promising Material by Using Residue Waste from Bisphenol A Manufacturing to Prepare Fluid-Loss-Control Additive in Oil Well Drilling Fluid

    Directory of Open Access Journals (Sweden)

    Zhi-Lei Zhang

    2013-01-01

    Full Text Available The residues mixture from Bisphenol A manufacturing process was analyzed. Fourier transform infrared (FTIR spectroscopy, gas chromatography-mass spectrometry (GC-MS, and nuclear magnetic resonance (NMR were used to characterize the residues. The results indicated that the residues were complex mixture of several molecules. 3-(2-Hydroxyphenyl-1,1,3-trimethyl-2,3-dihydro-1H-inden-5-ol and phenol were the main components of the residues. The technical feasibility of using it as phenol replacement in fluid-loss-control additive production was also investigated. The fluid-loss-control capacity of the novel additive was systematically investigated. It was discovered that the well fluid-loss performance of the prepared additive can be achieved, especially at high temperature.

  18. Importance of the planning activities, cutting, handling and analysis of the nuclei of oil well drilling; Importancia de las actividades de planificacion, corte, manejo y analisis de los nucleos de perforacion de pozos petroleros

    Energy Technology Data Exchange (ETDEWEB)

    Contreras L, Enrique A; Garcia M, Pablo [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

    2007-07-01

    In the geologic formation where the oil deposits are located, diverse types of rocks perform functions as structural elements, storage containers for hydrocarbon water and calorific energy, as well as impermeable barriers and transport means of the energy and the fluids. Among the most important properties that are used to describe these functions are the porosity, the permeability, the compressibility of the pores volume, the formation resistivity factor, the saturation exponent, the velocity of acoustic waves P and S, the relative permeability, the capillary pressures, the elastic constants and other mechanical properties, the thermal expansion, coefficient, the thermal conductivity, the thermal diffusivity and the specific heat. The execution of an ample variety of activities related to the stages of exploration, location, evaluation and development of the oil deposits, depends strongly on having a good knowledge of the magnitude and the spatial variability of these properties. The technical feasibility as well as the economics in developing a prospectus of oil deposit, depends on that the intervening rocks exhibit a suitable combination of their properties, thus constituting a confining and storing geologic structure of hydrocarbons that is feasible to be developed technically, at the same time of having the economic potential of yielding an economic benefit. In this context, from the experience platform on the subject existing in the Laboratorio de Yacimientos of the Instituto de Investigaciones Electricas. The present article approaches the relevance which have the activities of cutting, handling and laboratory analysis of the oil well drilling nuclei, for the geologic evaluation of the formation, in relation to the characterization, the evaluation and the advantage of the oil deposits. [Spanish] En las formaciones geologicas donde se encuentran emplazados los yacimientos petroleros, diversos tipos de rocas desempenan funciones como elementos estructurales

  19. New round for oil

    International Nuclear Information System (INIS)

    Delamarche, Myrtille

    2018-01-01

    After three years of crisis, oil companies are now strongly reinvesting, while oil prices are stabilizing at a reasonable long-term level, notably due to a rising demand from developing countries. Examples of new investments made by majors such as Total, Shell or Exxon but also by national companies and junior companies, are given. Oil price evolution as well as cost reductions (thanks notably to the digitalisation of the sector, leading to a decrease in exploration costs) are analyzed. The importance of the US oil production, and particularly shale oil production, is pinpointed

  20. Development and application of the capacity to make tests of dynamic displacement in samples of oil well drilling cores; Desarrollo y aplicacion de la capacidad para realizar pruebas de desplazamiento dinamico en muestras de nucleos de perforacion de pozos petroleros

    Energy Technology Data Exchange (ETDEWEB)

    Contreras L, Enrique; Garcia M, Pablo [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

    2001-07-01

    In the Laboratory of Deposits of the Gerencia de Geotermia of the Instituto de Investigaciones Electricas (IIE) the capacity has been developed to make tests of dynamic oil displacement by means of gas or brine injection in samples of oil well drilling cores. Also the methodologies to interpret the results of these tests in terms of dynamics and the efficiency of the oil recovery in terms of the relative permeability have been developed. These capacities represent a very important contribution towards the improvement of the insufficiency that exists in the country to make the large amount of tests of dynamic displacement that demand the different Actives of PEMEX Exploration and Production (PEP), since they satisfy their necessities of data on which the activities of design and implementation of the most suitable techniques for the hydrocarbon recovery of the oil deposits lean. In the present work these capacities are described and some examples are presented of the results that have been obtained from their application in special studies of drilling cores, which have been recently made in the Laboratory of Deposits of the IIE for diverse Actives of PEP exploitation. [Spanish] En el laboratorio de yacimientos de la Gerencia de Geotermia del Instituto de Investigaciones Electricas (IIE) se ha desarrollado la capacidad de realizar pruebas de desplazamiento dinamico de aceite mediante inyeccion de salmuera o de gases en muestras de nucleos de perforacion de pozos petroleros. Tambien se han desarrollado las metodologias para interpretar los resultados de estas pruebas en terminos de la dinamica y la eficiencia de la recuperacion de aceite y en terminos de la permeabilidades relativas. Estas capacidades representan una contribucion muy importante hacia el mejoramiento de la insuficiencia que existe en el pais para realizar la gran cantidad de pruebas de desplazamiento dinamico que demandan los diferentes activos de explotacion de PEMEX Exploracion y Produccion (PEP), ya

  1. Mexican oil industry: Shifting to difficult oil

    Energy Technology Data Exchange (ETDEWEB)

    Bazan G., Gerardo; Gonzalez, Cristobal J.

    2010-09-15

    Mexico has stepped into an important transition of declining oil fields and new challenging oil projects. The aim of this paper is to show a new perspective of the oil resources that have been exploited throughout the Mexican territory, as well as the remaining resources yet to be exploited. We have developed a resources/production-costs chart that illustrates the historical and future development of the Mexican oil industry, showing the shift that the industry will face in the coming years; this chart was taken from a model already in use by the most prestige energy agencies in the world.

  2. Cyclonic multiphase flow measurement system GLCC{copyright}1 for oil well capacity evaluation; Sistema de medicion de flujo multifasico mediante tecnologia ciclonica GLCC{copyright}1 para aforo de pozos petroleros

    Energy Technology Data Exchange (ETDEWEB)

    Godoy-Alcantar, J. M; Cervantes-Martinez, G; Cruz-Maya, J. A; Hernandez-Buenfil, M. A; Ramirez-Antonio, I [Instituto Mexicano del Petroleo, Mexico, D.F, (Mexico)]. E-mail: mgodoy@imp.mx

    2008-10-15

    This paper shows the development of a portable multiphase flow measurement system based in cyclonic separation technology GLCC{copyright}1. This system is aimed for oil well measurement and was developed in three phases; the first devoted to the geometric design of a cyclonic separator by means of designs sofware GLCCV7.8 and the selection of measurement instrumentation and flux control valves. In the second phase, the automatic control system was designed for the implementation of four control strategies each one related with a possible scenario of the well behavior. The third constitutes the integration of the measurement and control devices through a user interface aimed for visualization, information processing and system's operation and control. Experimental results in oil well measurements show the efficiency and workability of the integrated system. [Spanish] En el presente trabajo se muestra el desarrollo de un sistema portatil para la medicion de flujo multifasico, basado en la tecnologia de separacion ciclonica GLCC{copyright}1 y su utilizacion el aforo de pozos petroleros. El desarrollo del sistema se compone de tres fases, la primera se orienta hacia el diseno geometrico de un separador tipo ciclonico por medio del simulador GLCCV 7.8, asi como el dimensionamiento y la seleccion de los instrumentos de medicion y valvulas de control de flujo. En la segunda fase, se lleva a cabo la etapa de diseno del control automatico del sistema, el cual se fundamenta en el desarrollo e implantacion de cuatro estrategias de control basadas en el comportamiento dinamico de las variables de produccion del pozo; la tercera fase, la constituye el desarrollo de una interfaz para la integracion y operacion conjunta de los componentes de medicion y control del sistema, asi como de visualizacion, procesamiento y almacenamiento de la informacion. Se muestran los resultados experimentales de una prueba de medicion realizada en campo, las mediciones obtenidas muestran la

  3. Performance analysis of progressive cavity pumps in oil wells with high BSW (Basic Sediment Water); Analise do desempenho de elastometros do bombeio de cavidades progressivas em pocos de petroleo com elavado BSW (Basic Sediment Water)

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Cindi Alves; Santos, Joao Paulo Lobo dos; Lobato, Ana Katerine de Carvalho Lima; Santos, Luiz Carlos Lobato dos [Universidade Federal da Bahia, BA (Brazil); Duarte, Lindemberg de Jesus Nogueira [Universidade Federal do Rio Grande do Norte, RN (Brazil)

    2012-07-01

    One of the most important equipment in the progressing cavity pump (PCP) is the subsurface pump, which comprises a rotor and a stator covered internally by an elastomer. This is responsible for sealing the pump and, consequently, for elevating the fluids. In fact, this polymer is used because of the ability to generate pressure in the pump by the seals formed between the cavities. In order to guarantee that the elastomer will have a good performance in the PCP system certain requirements need to be checked, such as: stress, elongation, hardness, resilience, permeability and adhesion. The fluids and solids handled by the PCP system, allied to high temperatures can cause premature wear in the elastomers. The most common reactions which are also observed in most of the wells are swelling, shrinkage, softening, hardening and explosive decompression. In this sense, the aim of this work is to study some elastomers which were chosen based on compatibility tests conducted by a major oil company. The problems that occurred in the wells will be analyzed in order to verify whether the choice of the elastomer had some influence on system failure. For this purpose, the intervention reports, efficiency tests and failure analysis reports will be used. At the end of this work, it was possible to diagnose the causes, consequences and solutions to inherent problems at various oil wells in a field that is in an advanced stage of recovery. Finally, it was concluded that simple changes in the process of compatibility analysis would help to increase the reliability level of the tests, especially the problems observed during the PCP operation in hostile environments. (author)

  4. Music acupuncture stimulation method.

    Science.gov (United States)

    Brătilă, F; Moldovan, C

    2007-01-01

    Harmonic Medicine is the model using the theory that the body rhythms synchronize to an outer rhythm applied for therapeutic purpose, can restores the energy balance in acupuncture channels and organs and the condition of well-being. The purpose of this scientific work was to demonstrate the role played by harmonic sounds in the stimulation of the Lung (LU) Meridian (Shoutaiyin Feijing) and of the Kidney (KI) Meridian (Zushaoyin Shenjing). It was used an original method that included: measurement and electronic sound stimulation of the Meridian Entry Point, measurement of Meridian Exit Point, computer data processing, bio feed-back adjustment of the music stimulation parameters. After data processing, it was found that the sound stimulation of the Lung Meridian Frequency is optimal between 122 Hz and 128 Hz, with an average of 124 Hz (87% of the subjects) and for Kidney Meridian from 118 Hz to 121 Hz, with an average of 120 Hz (67% of the subjects). The acupuncture stimulation was more intense for female subjects (> 7%) than for the male ones. We preliminarily consider that an informational resonance phenomenon can be developed between the acupuncture music stimulation frequency and the cellular dipole frequency, being a really "resonant frequency signature" of an acupoint. The harmonic generation and the electronic excitation or low-excitation status of an acupuncture point may be considered as a resonance mechanism. By this kind of acupunctural stimulation, a symphony may act and play a healer role.

  5. The SLIMITRE system: T-P-CCL registry in high temperature oil wells; El sistema SLIMITRE: registro T-P-CCL en pozos petroleros de alta temperatura

    Energy Technology Data Exchange (ETDEWEB)

    Iglesias R, Eduardo and others [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

    2001-07-01

    PEMEX Exploration and Production (PEP), through its Management of Well Productivity of the Subdivision of Technology and Professional Development (GTDP) and of its Active Luna, faced the problematic of carrying out simultaneous recordings of temperature and pressure in high temperature flowing wells. Capitalizing the experience and know-how of the Gerencia de Geotermia (GG) of the Instituto de Investigaciones Electricas (IIE) in this field, it ordered the resolution of the described problematic, by means of the development of appropriate tools. In order to compliment this order, the GG of the IIE developed the SLIMETRE system, in close collaboration with the personnel of PEP involved in the project. This project framed in the Agreement of Collaboration for the rendering of services between PEMEX Exploration and Production and the Instituto de Investigaciones Electricas. In the sections that follow appear the main parameters of design, the architecture of the system is explained, the tools and the subsystem of data acquisition are described; the obtained results are exposed and the conclusions appear. [Spanish] Pemex Exploracion y Produccion (PEP), a traves de su Gerencia de Productividad de Pozos de la Subdireccion de Tecnologia y Desarrollo Profesional (GTDP) y de su Activo Luna, encaro la problematica de efectuar registros simultaneos de temperatura y presion en pozos fluyentes de alta temperatura. Capitalizando la experiencia y know-how de la Gerencia de Geotermia (GG) del Instituto de Investigaciones Electricas (IIE) en dicho campo, le encargo la resolucion de la problematica descrita, mediante el desarrollo de herramientas apropiadas. Para cumplimentar dicho encargo, la GG del IIE desarrollo el sistema SLIMETRE, en estrecha colaboracion con el personal de PEP involucrado en el proyecto. Este proyecto se enmarco en el Convenio de Colaboracion para la prestacion de servicios entre Pemex Exploracion y Produccion y el Instituto de Investigaciones Electricas. En

  6. Fine tuning a well-oiled machine: Influence of NK1.1 and NKG2D on NKT cell development and function.

    Science.gov (United States)

    Joshi, Sunil K; Lang, Mark L

    2013-10-01

    Natural killer T cells (NKT) represent a group of CD1d-restricted T-lineage cells that provide a functional interface between innate and adaptive immune responses in infectious disease, cancer, allergy and autoimmunity. There have been remarkable advances in understanding the molecular events that underpin NKT development in the thymus and in the complex array of functions in the periphery. Most functional studies have focused on activation of T cell antigen receptors expressed by NKT cells and their responses to CD1d presentation of glycolipid and related antigens. Receiving less attention has been several molecules that are hallmarks of Natural Killer (NK) cells, but nonetheless expressed by NKT cells. These include several activating and inhibitory receptors that may fine-tune NKT development and survival, as well as activation via antigen receptors. Herein, we review the possible roles of the NK1.1 and NKG2D receptors in regulating development and function of NKT cells in health and disease. We suggest that pharmacological alteration of NKT activity should consider the potential complexities commensurate with NK1.1 and NKG2D expression. Published by Elsevier B.V.

  7. Short-term outlook for Canadian crude oil to 2006 : an energy market assessment

    International Nuclear Information System (INIS)

    2005-09-01

    The National Energy Board monitors the supply of all energy commodities in Canada along with the demand for Canadian energy commodities in domestic and export markets. This report is intended to expand the effectiveness of the Board's monitoring activities by providing an assessment of the current state of the petroleum industry and the potential for growth. It provides an 18-month outlook on international and domestic crude oil prices; drilling and exploration activity; supply projections for Canadian crude oil and petroleum products; Canada's crude oil trade balance and markets for Canadian crude; existing export pipeline networks and project expansion plans; and, the Canadian petroleum products industry and the impact of higher prices. It also identifies the major issues and challenges associated with the development of Canada's crude oil. The 2 major oil producing areas in Canada are the Western Canada Sedimentary Basin (WCSB) including the oil sands, and offshore eastern Canada. While conventional production in the WCSB is declining, development focus has shifted to Alberta's oil sands as well as Hibernia, Terra Nova and White Rose, the 3 major oil fields offshore Newfoundland and Labrador. High energy prices have resulted in record profits for the Canadian oil and gas industry, and has stimulated billions of dollars in investment, with Alberta's oil sands being the main beneficiary. The 19 refineries in Canada have been operating at about 90 per cent capacity for the last several years due to strong demand for transportation fuels. 10 tabs., 37 figs., 2 appendices

  8. Encyclopedia of well logging

    International Nuclear Information System (INIS)

    Desbrandes, R.

    1985-01-01

    The 16 chapters of this book aim to provide students, trainees and engineers with a manual covering all well-logging measurements ranging from drilling to productions, from oil to minerals going by way of geothermal energy. Each chapter is a summary but a bibliography is given at the end of each chapter. Well-logging during drilling, wireline logging equipment and techniques, petroleum logging, data processing of borehole data, interpretation of well-logging, sampling tools, completion and production logging, logging in relief wells to kill off uncontrolled blowouts, techniques for high temperature geothermal energy, small-scale mining and hydrology, logging with oil-base mud and finally recommended logging programs are all topics covered. There is one chapter on nuclear well-logging which is indexed separately. (UK)

  9. Evaluation of polymers of different degrees viscosities as additives for drilling fluids for oil well; Avaliacao de polimeros de diferentes graus de viscosidades como aditivos para fluidos de perfuracao de pocos de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Farias, K.V.; Amorim, L.V.; Silva, A.V. [Universidade Federal de Campina Grande (DEMa/UFCG), PB (Brazil); Lira, H.L. [Universidade Federal de Campina Grande (CCT/UFCG), PB (Brazil). Centro de Ciencias e Tecnologia. Unidade Academica de Engenharia de Materiais], e-mail: kassiefarias@gmail.com

    2008-07-01

    The objective of this work is to study the polymers influence of different degrees of viscosity, used as viscositying and filtered reducer additives, in the rheological, filtration and lubricity properties of drilling fluids for oil wells. Were determined the rheological behavior, the apparent and plastic viscosities, the yield limit and gel force, the filtered volume and the lubricity coefficient in accordance with API standard. The fluids showed pseudoplastic behavior with properties close to the standard fluid; the increase of viscositying and filtered reducer concentrations lead to the increase of rheological properties and the filtered reducer values, from the concentration of 3,5g/350mL of water it acted as viscositying, increasing the values of apparent and plastic viscosities, yield limit and gel force, being 3,0g/350mL of water the adequate concentration of this additive, promoting better results of rheological and filtration properties. (author)

  10. Cement for oil well developed from ordinary cement: characterization physical, chemical and mineralogical; Cimento para poco de petroleo desenvolvido a partir de cimento comum: caracterizacao fisica, quimica e mineralogica

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, D.N.S.; Neves, G. de A.; Chaves, A.C.; Mendonca, A.M.G.D.; Lima, M.S. de [Universidade Federal de Campina Grande (UFCG), PB (Brazil); Bezerra, U.T., E-mail: daninascimento.eng@gmail.com [Instituto Federal de Educacao, Ciencia e Tecnologia da Paraiba (IFPB), Campina Grande, PB (Brazil)

    2012-07-01

    This work aims to characterize a new type of cement produced from the mixture of ordinary Portland cement, which can be used as an option in the cementing of oil wells. To enable this work we used the method of lineal programming for the new cement composition, then conducted tests to characterize through particle size analysis by laser diffraction, chemical analysis by EDX, TGA, X-ray diffraction, time grip, resistance to compression. The overall result showed that the new cement had made low-C3A, takes more time to the CPP, thermal stability up to 500 ° C, the kinetics of hydration and low levels of major components consistent with the specifications of ABNT. (author)

  11. Papers of the PTAC wireless, telecommunications and e-business forum : using wireless, SCADA, and well data life cycle management technology to boost productivity and reduce costs in the upstream oil and gas industry

    International Nuclear Information System (INIS)

    2004-01-01

    The main focus of this forum was the use of wireless, telecommunications and e-business as a means of improving efficiency and productivity in the upstream oil and gas industry. The use of new communications technologies in asset monitoring and business performance was discussed, as well as industrial automation and wireless connectivity in conjunction with Supervisory Control and Data Acquisition (SCADA) systems. New technologies in the areas of maintenance and decision support and synergy integration were introduced. New health, safety and environmental performance tools were presented. Issues concerning secure communications and document exchange expenses were also introduced, as well as different methods of closing data gaps between joint interest partners. Specific tools and software concerning compliance management with web-based and remote field data capture technology were discussed, as well as the collection and display of well-site data using newly developed BlueGauge technology. Eleven papers were presented in this forum, of which three were catalogued separately for inclusion in this database. tabs., figs

  12. Papers of the PTAC wireless, telecommunications and e-business forum : using wireless, SCADA, and well data life cycle management technology to boost productivity and reduce costs in the upstream oil and gas industry

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2004-07-01

    The main focus of this forum was the use of wireless, telecommunications and e-business as a means of improving efficiency and productivity in the upstream oil and gas industry. The use of new communications technologies in asset monitoring and business performance was discussed, as well as industrial automation and wireless connectivity in conjunction with Supervisory Control and Data Acquisition (SCADA) systems. New technologies in the areas of maintenance and decision support and synergy integration were introduced. New health, safety and environmental performance tools were presented. Issues concerning secure communications and document exchange expenses were also introduced, as well as different methods of closing data gaps between joint interest partners. Specific tools and software concerning compliance management with web-based and remote field data capture technology were discussed, as well as the collection and display of well-site data using newly developed BlueGauge technology. Eleven papers were presented in this forum, of which three were catalogued separately for inclusion in this database. tabs., figs.

  13. Intelligent sensors for evaluating reservoir and well profiles in horizontal wells : Saudi Arabia case histories

    Energy Technology Data Exchange (ETDEWEB)

    Al-Buali, M.H.; Dashash, A.A. [Saudi Aramco, Dhahran (Saudi Arabia); El Gammal, T.; Arevalo, F.; Torne, J. [Halliburton Energy Services, Calgary, AB (Canada)

    2010-07-01

    Horizontal wells are commonly used in Saudi Arabia because they have proven advantages in optimizing production and cost. However, in order to ensure proper production, these wells occasionally require downhole measurements of the flow profile; wellbore parameters such as water entry points; and productivity index for remedial action, such as water shut off or well stimulation. Evaluating the performance of a well also contributes to a better understanding of sweep, water production and cross flow, particularly in long reach wells. The most common flow regime at downhole conditions is a stratified flow regime in which lighter oil flows on top and heavier water flows on bottom. Slugging and bubbling flow regimes are typical of low oil flow rate and are considered unstable flow regimes. This paper described a new generation of production logging tools (PLTs) that have been used on some horizontal wet producers located in Saudi Arabia. The new PLTs consists of arrays of spinners and sensors to log the entire cross section to describe the horizontal flow regime and measure the downhole production and phases. In an effort to find the best logging procedure, the PLT was tested using two methods, notably coiled tubing (CT) and wireline tractor. It was concluded that PLTs are reliable and accurate. Case studies involving planning, deployment, data acquisition, and detailed analysis of PLTs were presented. 35 refs., 1 tab., 20 figs.

  14. Impact of an indigenous microbial enhanced oil recovery field trial on microbial community structure in a high pour-point oil reservoir

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Fan; Zhang, Xiao-Tao; Hou, Du-Jie [China Univ. of Geosciences, Beijing (China). The Key Lab. of Marine Reservoir Evolution and Hydrocarbon Accumulation Mechanism; She, Yue-Hui [Yangtze Univ., Jingzhou, Hubei (China). College of Chemistry and Environmental Engineering; Huazhong Univ. of Science and Technology, Wuhan (China). College of Life Science and Technology; Li, Hua-Min [Beijing Bioscience Research Center (China); Shu, Fu-Chang; Wang, Zheng-Liang [Yangtze Univ., Jingzhou, Hubei (China). College of Chemistry and Environmental Engineering; Yu, Long-Jiang [Huazhong Univ. of Science and Technology, Wuhan (China). College of Life Science and Technology

    2012-08-15

    Based on preliminary investigation of microbial populations in a high pour-point oil reservoir, an indigenous microbial enhanced oil recovery (MEOR) field trial was carried out. The purpose of the study is to reveal the impact of the indigenous MEOR process on microbial community structure in the oil reservoir using 16Sr DNA clone library technique. The detailed monitoring results showed significant response of microbial communities during the field trial and large discrepancies of stimulated microorganisms in the laboratory and in the natural oil reservoir. More specifically, after nutrients injection, the original dominant populations of Petrobacter and Alishewanella in the production wells almost disappeared. The expected desirable population of Pseudomonas aeruginosa, determined by enrichment experiments in laboratory, was stimulated successfully in two wells of the five monitored wells. Unexpectedly, another potential population of Pseudomonas pseudoalcaligenes which were not detected in the enrichment culture in laboratory was stimulated in the other three monitored production wells. In this study, monitoring of microbial community displayed a comprehensive alteration of microbial populations during the field trial to remedy the deficiency of culture-dependent monitoring methods. The results would help to develop and apply more MEOR processes. (orig.)

  15. Impact of an indigenous microbial enhanced oil recovery field trial on microbial community structure in a high pour-point oil reservoir.

    Science.gov (United States)

    Zhang, Fan; She, Yue-Hui; Li, Hua-Min; Zhang, Xiao-Tao; Shu, Fu-Chang; Wang, Zheng-Liang; Yu, Long-Jiang; Hou, Du-Jie

    2012-08-01

    Based on preliminary investigation of microbial populations in a high pour-point oil reservoir, an indigenous microbial enhanced oil recovery (MEOR) field trial was carried out. The purpose of the study is to reveal the impact of the indigenous MEOR process on microbial community structure in the oil reservoir using 16Sr DNA clone library technique. The detailed monitoring results showed significant response of microbial communities during the field trial and large discrepancies of stimulated microorganisms in the laboratory and in the natural oil reservoir. More specifically, after nutrients injection, the original dominant populations of Petrobacter and Alishewanella in the production wells almost disappeared. The expected desirable population of Pseudomonas aeruginosa, determined by enrichment experiments in laboratory, was stimulated successfully in two wells of the five monitored wells. Unexpectedly, another potential population of Pseudomonas pseudoalcaligenes which were not detected in the enrichment culture in laboratory was stimulated in the other three monitored production wells. In this study, monitoring of microbial community displayed a comprehensive alteration of microbial populations during the field trial to remedy the deficiency of culture-dependent monitoring methods. The results would help to develop and apply more MEOR processes.

  16. Simulation study of huff-n-puff air injection for enhanced oil recovery in shale oil reservoirs

    Directory of Open Access Journals (Sweden)

    Hu Jia

    2018-03-01

    Full Text Available This paper is the first attempt to evaluate huff-n-puff air injection in a shale oil reservoir using a simulation approach. Recovery mechanisms and physical processes of huff-n-puff air injection in a shale oil reservoir are investigated through investigating production performance, thermal behavior, reservoir pressure and fluid saturation features. Air flooding is used as the basic case for a comparative study. The simulation study suggests that thermal drive is the main recovery mechanism for huff-n-puff air injection in the shale oil reservoir, but not for simple air flooding. The synergic recovery mechanism of air flooding in conventional light oil reservoirs can be replicated in shale oil reservoirs by using air huff-n-puff injection strategy. Reducing huff-n-puff time is better for performing the synergic recovery mechanism of air injection. O2 diffusion plays an important role in huff-n-puff air injection in shale oil reservoirs. Pressure transmissibility as well as reservoir pressure maintenance ability in huff-n-puff air injection is more pronounced than the simple air flooding after primary depletion stage. No obvious gas override is exhibited in both air flooding and air huff-n-puff injection scenarios in shale reservoirs. Huff-n-puff air injection has great potential to develop shale oil reservoirs. The results from this work may stimulate further investigations.

  17. Oil/gas collector/separator for underwater oil leaks

    Energy Technology Data Exchange (ETDEWEB)

    Henning, C.D.

    1992-12-31

    This invention is comprised of an oil/gas collector/separator for recovery of oil leaking, for example, from an offshore or underwater oil well. The separator is floated over the point of the leak and tethered in place so as to receive oil/gas floating, or forced under pressure, toward the water surface from either a broken or leaking oil well casing, line, or sunken ship. The separator is provided with a downwardly extending skirt to contain the oil/gas which floats or is forced upward into a dome wherein the gas is separated from the oil/water, with the gas being flared (burned) at the top of the dome, and the oil is separated from water and pumped to a point of use. Since the density of oil is less than that of water it can be easily separated from any water entering the dome.

  18. Oil shale commercialization study

    Energy Technology Data Exchange (ETDEWEB)

    Warner, M.M.

    1981-09-01

    Ninety four possible oil shale sections in southern Idaho were located and chemically analyzed. Sixty-two of these shales show good promise of possible oil and probable gas potential. Sixty of the potential oil and gas shales represent the Succor Creek Formation of Miocene age in southwestern Idaho. Two of the shales represent Cretaceous formations in eastern Idaho, which should be further investigated to determine their realistic value and areal extent. Samples of the older Mesozonic and paleozoic sections show promise but have not been chemically analyzed and will need greater attention to determine their potential. Geothermal resources are of high potential in Idaho and are important to oil shale prospects. Geothermal conditions raise the geothermal gradient and act as maturing agents to oil shale. They also might be used in the retorting and refining processes. Oil shales at the surface, which appear to have good oil or gas potential should have much higher potential at depth where the geothermal gradient is high. Samples from deep petroleum exploration wells indicate that the succor Creek shales have undergone considerable maturation with depth of burial and should produce gas and possibly oil. Most of Idaho's shales that have been analyzed have a greater potential for gas than for oil but some oil potential is indicated. The Miocene shales of the Succor Creek Formation should be considered as gas and possibly oil source material for the future when technology has been perfectes. 11 refs.

  19. Asphaltene precipitates in oil production wells

    DEFF Research Database (Denmark)

    Kleinitz, W,; Andersen, Simon Ivar

    1998-01-01

    compounds in the organic scales from operations definitely differed from the data published in the literature. In order to dissolve the precipitates and thus eliminate the damage, various organic solvents and industrial solvent mixtures were examined. The kinetics of the dissolution process in operational...... production is also explained and discussed in detail from a reservoir engineering standpoint....

  20. Stone oil and well-fire

    International Nuclear Information System (INIS)

    Hansen, G.

    1991-01-01

    This book on the history of the petroleum industry was originally published in German in 1975. It has recently been translated into English. The book is full of photographs and drawings which help trace the use of petroleum from the present back into prehistoric times

  1. Brain Stimulation Therapies

    Science.gov (United States)

    ... Magnetic Seizure Therapy Deep Brain Stimulation Additional Resources Brain Stimulation Therapies Overview Brain stimulation therapies can play ... for a shorter recovery time than ECT Deep Brain Stimulation Deep brain stimulation (DBS) was first developed ...

  2. ICMS: problems from the oil well to gas station (a risk for the investment planning in the oil, gas and energy data); ICMS: problemas do poco ao posto (um risco para o planejamento de investimentos no setor de petroleo, gas e energia)

    Energy Technology Data Exchange (ETDEWEB)

    Sousa, Luciano [Lex Consult, Salvador, BA (Brazil)

    2004-07-01

    In 1988, by changing the Constitution, that taxed the oil, based products and electric power with single tax, of Federal responsibility, going to ICMS and, as a consequence, to the states, the tributes on this products, caused not only a tribute reform, but also, as a bad view an undesired administrative reform of electric power policy. The Union, that used to keep the control of policy and tributes on that section, kept with the policy, but had lost the control over theses tributes. The workability of these investment projects now has to consider the tax charged by ICMS. Is good to say that the public's policy, after 1988, those do not regard the ICMS, may not be possible to be done. Further this worrying situation, the ICMS application has been discordant with this section, promoting juridical obstacle and doubtful legal interpretation, from the upstream to the downstream. Facing this situation, what is wanted in this work is to stimulate discussion about the necessity to find alternatives ways out, either to rescue to the public section the effective conduction of the policy over this section, or to alert the investor about the necessity to make a suitable plan, looking forward to protect your investment from the dangers of tax legislation. (author)

  3. Oil shale activities in China

    International Nuclear Information System (INIS)

    Peng, D.; Jialin, Q.

    1991-01-01

    China has abundant oil shale resources, of the Early Silurian to Neogene age, the most important being the Tertiary period. The proved oil shale reserves in Fushun amount to 3.6 billion t, in Maoming 4.1 billion t. In Fushun, oil shale is produced by open-pit mining as a byproduct of coal, in Maoming it is also mined in open pits, but without coal. In China, scale oil has been produced from oil shale for 60 years. Annual production of crude shale oil amounts to about 200 000 t. The production costs of shale oil are lower than the price of crude petroleum on the world market. China has accumulated the experience and technologies of oil shale retorting. The Fushun type retort has been elaborated, in which the latent and sensible heat of shale coke is well utilized. But the capacity of such retort is relatively small, therefore it is suitable for use in small or medium oil plants. China has a policy of steadily developing shale oil industry. China is conducting oil shale research and developing oil shale processing technology. Much attention is being pay ed to the comprehensive utilization of oil shale, shale oil, and to environmental problems. In China, oil shale is mostly used for producing shale by retorting, attention will also be paid to direct combustion for power generation. Great achievements in oil shale research have been made in the eighties, and there will be a further development in the nineties. (author), 12 refs., 3 tabs

  4. Deceased Slabs Drive Oil

    Science.gov (United States)

    Stein, H. J.; Hannah, J. L.

    2017-12-01

    The application of Re-Os isotope geochemistry to dating single oils is a nascent field [1,2]. Challenges include dissection of oils into asphaltene-maltene (ASPH-MALT) components in a way that preserves meaningful chronologic and source information. Significantly, oil-water mixing rapidly transfers Os to the oil, while Re exchange is sluggish [3]. The Os initial ratio of the oil is shifted in the direction of Os carried in the aqueous fluid, whereas the Re-Os isotopic age is preserved. We show that this phenomenon is operative in natural systems. Further, we show that deserpentinization of old oceanic slabs [4], may be linked to expulsion of Os-enriched waters into overlying sedimentary sections - a process that may be of fundamental importance for oil generation. This conclusion does not diminish the role of traditional organic-rich shales as source rocks for the hydrocarbon, but shows that external fluids are essential to petroleum generation. Moreover, the external fluids may be an important driver for expulsion and migration of oils. We have taken apart several petroleum systems from source rock, to residual oil, to tar mat development, to in situ live oil, through to produced oil. In many cases, a fluid with low 187Os/188Os - unlike that of normal basinal brines - provides a critical component to the oil-water mixture. Funding - CHRONOS project supported by Norwegian petroleum industry (Eni-Norge, Lundin, Aker BP) Acknowledgement - Christine Fichler [4], who first queried us on old slabs and oil, and stimulated ideas. [1] Georgiev, S.V., Stein, H.J., Hannah, J.L., Galimberti, R., Nali, M., Yang, G., and Zimmerman, A. (2016) Re-Os dating of maltenes and asphaltenes within single samples of crude oil: Geochim. Cosmochim. Acta 179: 53-75. [doi.org/10.1016/j.gca.2016.01.016] [2] DiMarzio, J., Georgiev, S.V., Stein, H.J., and Hannah, J.L. (in press) Residency of rhenium and osmium in a heavy crude oil: Geochim. Cosmochim. Acta. [3] Hurtig, N.C., Georgiev, S

  5. Oil Spills

    Science.gov (United States)

    Oil spills often happen because of accidents, when people make mistakes or equipment breaks down. Other causes include natural disasters or deliberate acts. Oil spills have major environmental and economic effects. Oil ...

  6. Physical properties and caffeine release from creams prepared with different oils

    Directory of Open Access Journals (Sweden)

    Wojciechowska Katarzyna

    2014-12-01

    Full Text Available Caffeine is a methylxanthine typically found in the Coffee Arabica L plant. Generally, caffeine is well-known as a orally administered mild stimulant of the central nervous system. However, for cosmetic purpose, caffeine is an active compound ingredient, at 7% concentration, in several anticellulite products. The efficiency of this mode of delivery is not fully understood. Hence, the aim of the study was to ascertain the effectiveness of particular carriers to release this ingredient. In so doing, we prepared six creams based upon different oils (Sesame oil, Rice oil, Walnut oil, Coconut oil, Sweet almond oil and Jojoba oil, containing 5% of caffeine, and compared the release of the substance from the obtained preparations. Initially, all of the creams were subjected to a variety of physical tests, among these being for slippage and spreadability. Furthermore, their rheological properties were evaluated. Subsequently, the creams were tested for caffeine release. In the slippage and spreadability tests, the coconut oil-based cream was revealed as having the best parameters. However, the rheological tests showed that all of the preparations had the pseudoplastic character of flowing according to the Ostwald de Waele power law model. The power low index (n for all the preparations was from 0.2467-0.3179 at 20°C and 0.2821-0.3754 at 32°C. At 20°C, the Sesame oil-, Walnut oil-, Sweet almond oil- and Jojoba oil-based creams were thixotropic, but at 32°C, thixotropy appeared only in the Walnut oil-based creams.

  7. OPEC's optimal crude oil price

    International Nuclear Information System (INIS)

    Horn, Manfred

    2004-01-01

    OPEC decided to stabilise oil prices within a range of 22-28 US Dollar/barrel of crude oil. Such an oil-price-level is far beyond the short and long run marginal costs of oil production, beyond even that in regions with particularly high costs. Nevertheless, OPEC may achieve its goal if world demand for oil increases substantially in the future and oil resources outside the OPEC are not big enough to accordingly increase production. In this case OPEC, which controls about 78% of world oil reserves, has to supply a large share of that demand increase. If we assume OPEC will behave as a partial monopolist on the oil market, which takes into consideration the reaction of the other producers to its own sales strategy, it can reach its price target. Lower prices before 2020 are probable only if the OPEC cartel breaks up. Higher prices are possible if production outside OPEC is inelastic as assumed by some geologists, but they would probably stimulate the production of unconventional oil based on oil sand or coal. Crude oil prices above 30 US Dollar/barrel are therefore probably not sustainable for a long period. (Author)

  8. Oil and gas developments in western Canada in 1981

    Energy Technology Data Exchange (ETDEWEB)

    Hay, P.W.; Robertson, D.C.

    1982-12-01

    In 1981 there was a marked slump in drilling activity in western Canada, resulting from the combined effects of the National Energy Program (NEP), economic recession and a worldwide oil surplus. The number of wells drilled dropped by 22% to a total of 6,904. Exploratory drilling decreased 19% to 3,074 wells, and development drilling decreased 25% to 3,830 wells. The exploratory success rate also decreased to 62% in 1981, based on 740 oil discoveries and 1,172 gas discoveries. The development success rate decreased slightly to 88%, with 1,334 oil discoveries and 2,034 gas discoveries. Average well depth increased in four of the five western areas, but total revenue from land sales plummetted to half of the previous years' record totals. Average price per hectare also dropped. In Alberta, significant exploration activity was centred in the Shekilie, Golden-Evi and West Pembina areas, while major gas discoveries were made at Whiskey and Elmworth, and oil discoveries at Tangent. No significant new discoveries were made in British Columbia or Saskatchewan, but the 1980 Manitoba oil discovery at Waskada continued to stimulate activity. Preliminary results from the Nechako Basin drilling in central British Columbia proved to be disappointing with three successive dry holes. In the Arctic Islands, two major oil discoveries were made at Skate and Cisco, off Lougheed Island and a gas discovery at MacLean. Beaufort Sea drilling was hampered by weather, but nonetheless resulted in major oil discoveries a Koakoak and at a Kopanoar follow-up well. The year 1981 will probably be viewed as a major turning point in exploration in western Canada, with interest shifting from the provinces to the frontiers, and the participants now mainly Canadian-controlled companies.

  9. Counteracting foaming caused by lipids or proteins in biogas reactors using rapeseed oil or oleic acid as antifoaming agents

    DEFF Research Database (Denmark)

    Kougias, Panagiotis; Boe, Kanokwan; Einarsdottir, E. S.

    2015-01-01

    in biogas reactors fed with protein or lipid rich substrates. The results showed that both antifoams efficiently suppressed foaming. Moreover rapeseed oil resulted in stimulation of the biogas production. Finally, it was reckoned that the chemical structure of lipids, and more specifically their carboxylic...... deterioration of the methanogenic process. Many commercial antifoams are derivatives of fatty acids or oils. However, it is well known that lipids can induce foaming in manure based biogas plants. This study aimed to elucidate the effect of rapeseed oil and oleic acid on foam reduction and process performance...

  10. Reduced ex vivo stimulated IL-6 response in infants randomized to fish oil from 9 to 18 months, especially among PPARG2 and COX2 wild types

    DEFF Research Database (Denmark)

    Harslof, Laurine B. S.; Damsgaard, Camilla T.; Andersen, Anders D.

    2015-01-01

    We investigated whether n-3 LCPUFA affected immune function in late infancy and explored effect-modification by single nucleotide polymorphisms (SNPs) and links to intestinal microbiota. Infants (n=105) were randomized to fish oil (FO, 1.2 g/d n-3 LCPUFA) or sunflower oil (SO)-supplements from ag...

  11. Manitoba oil activity review, 1992

    International Nuclear Information System (INIS)

    1993-04-01

    In an annual survey of Manitoba's petroleum industry, data are presented on oil and natural gas leases and sales, geophysical activity, exploration and drilling activity, production, oil prices and sales value, royalties and taxes, direct revenues from oil exploration and development, reserves, industry expenditures, and oil fields. Throughout the report, explanations are given of the items covered. Descriptions are made of new developments, the oil market, oil policies, incentive programs, and industrial activities. During 1992, 28 wells were drilled, compared to 54 in 1991. Oil production was down ca 8% from 1991 levels, to 656,415 m 3 ; the value of the oil produced decreased 4% to ca $86.3 million; and provincial revenues from the oil industry decreased by 24%. Oil industry expenditures in the province were estimated at $58 million, down 16% from 1991. As of 4 January 1993, there were 11 oil fields and 120 non-confidential oil pools designated in Manitoba. Crude oil prices fluctuated throughout the year. In 1992, Manitoba's average crude oil price was $20.89/bbl, compared with 1991's average of $20.14/bbl. Manitoba Energy and Mines amended the Drilling Incentive Program to provide a 10,000 m 3 holiday volume for horizontal wells. 12 figs., 17 tabs

  12. Manitoba oil activity review, 1993

    International Nuclear Information System (INIS)

    1994-07-01

    In an annual survey of Manitoba's petroleum industry, data are presented on oil and natural gas leases and sales, geophysical activity, exploration and drilling activity, production, oil prices and sales value, royalties and taxes, direct revenues from oil exploration and development, reserves, industry expenditures, and oil fields. Throughout the report, explanations are given of the items covered. Descriptions are made of new developments, the oil market, oil policies, incentive programs, and industrial activities. During 1993, 87 wells were drilled, compared to 28 in 1992. Oil production was down ca 3% from 1992 levels, to 634,561 m 3 ; the value of the oil produced decreased 10% to ca $77.5 million; and provincial revenues from the oil industry decreased by 4%. Oil industry expenditures in the province were estimated at $73 million, up 26% from 1992. As of 4 January 1994, there were 11 oil fields and 120 non-confidential oil pools designated in Manitoba. Crude oil prices fluctuated throughout the year, between $15.12 and $21.50/bbl. In 1993, Manitoba's average crude oil price was $19.40/bbl, compared with 1992's average of $20.89/bbl. Manitoba Energy and Mines amended the Drilling Incentive Program to provide a 10,000 m 3 holiday volume for horizontal wells. 12 figs., 17 tabs

  13. Mineral oil industry

    NARCIS (Netherlands)

    Brasser, L.J.; Suess, M.J.; Grefen, K.; Reinisch, D.W.

    1985-01-01

    In this chapter a general picture is presented of the air pollution aspects in the mineral oil industry. The complete field is covered, starting from drilling operations and the well head up to the delivery of the products to the consumer. A large field of activities as is given by the mineral oil

  14. Oil spill recovery technology

    International Nuclear Information System (INIS)

    Nash, J.; Cooper, W.; Nee, V.; Nigim, H.

    1992-01-01

    Current deficiencies in oil spill cleanup processes have resulted in research and development of new cleanup technologies at the University of Notre Dame. Emphasis on reducing, reusing and recycling equipment and waste at a cleanup site has prompted advances in oil recovery technology as well as improvement in sorbent materials. (author)

  15. Thermotropic nanostructured gels with complex hierarchical structure and two gelling components for water shut-off and enhance of oil recovery

    Science.gov (United States)

    Altunina, L. K.; Kuvshinov, I. V.; Kuvshinov, V. A.; Kozlov, V. V.; Stasyeva, L. A.

    2017-12-01

    This work presents the results of laboratory and field tests of thermotropic composition MEGA with two simultaneously acting gelling components, polymer and inorganic. The composition is intended for improving oil recovery and water shut-off at oilfields developed by thermal flooding, and cyclic-steam stimulated oil production wells. The composition forms an in-situ "gel-in-gel" system with improved structural-mechanical properties, using reservoir or carrier fluid heat for gelling. The gel blocks water breakthrough into producing wells and redistribute fluid flows, thus increasing the oil recovery factor.

  16. Identifying oil/marine snow associations in mesocosm simulations of the Deepwater Horizon oil spill event using solid-state 13C NMR spectroscopy.

    Science.gov (United States)

    Hatcher, Patrick G; Obeid, Wassim; Wozniak, Andrew S; Xu, Chen; Zhang, Saijin; Santschi, Peter H; Quigg, Antonietta

    2018-01-01

    The Deepwater Horizon oil spill stimulated the release of marine snow made up of dead/living plankton/bacteria and their exopolymeric polysaccharide substances (EPS), termed marine oil snow (MOS), promoting rapid removal of oil from the water column into sediments near the well site. Mesocosm simulations showed that Macondo surrogate oil readily associates with the marine snow. Quantitative solid-state 13 C NMR readily distinguishes this oil from naturally formed marine snow and reveals that adding the dispersant Corexit enhances the amount of oil associated with the MOS, thus contributing to rapid removal from the water column. Solvent extraction of MOS removes the oil-derived compounds for analysis by one and two-dimensional GC/MS and evaluation of potential transformations they undergo when associated with the EPS. The results reveal that the oil associated with EPS is subjected to rapid transformation, in a matter of days, presumably by bacteria and fungi associated with EPS. Copyright © 2017 Elsevier Ltd. All rights reserved.

  17. Oil intensities and oil prices : evidence for Latin America

    OpenAIRE

    Alaimo, Veronica; Lopez, Humberto

    2008-01-01

    Crude oil prices have dramatically increased over the past years and are now at a historical maximum in nominal terms and very close to it in real terms. It is difficult to argue, at least for net oil importers, that higher oil prices have a positive impact on welfare. In fact, the negative relationship between oil prices and economic activity has been well documented in the literature. Ye...

  18. Technical review of the high energy gas stimulation technique

    Energy Technology Data Exchange (ETDEWEB)

    Haney, B.; Cuthill, D. [Computalog Ltd., Calgary, AB (Canada)

    1997-08-01

    High Energy Gas Stimulation (HEGS) or propellant stimulation is a process that enhances production of oil wells by decreasing wellbore damage and increasing near wellbore permeability. The technique has been used on about 7,000 wells with varying results. The HEGS tool is a cast cylinder of solid rocket propellant with a central ignition system. The propellant is fired and as it burns it produces a pressure load on the formation, increasing fracture volume which enhances the flow channels. Background information on the development and application of this stimulation technique was provided. The introduction of fractures around a wellbore is dependent on the pressure loading rate and the dynamic response of the rock. Propellant stimulation relies on controlling the pressure-time behaviour to maximize fracture growth by fluid pressurization. The process is composed of 3 sequential phases: (1) wellbore pressurization, (2) fracture initiation, and (3) fracture extension. A full description of each of these phases was provided. Geologic and well-tool factors that have a significant influence on the fracturing process such as in-situ stress, natural fractures and flaws, formation mechanical properties, formation fluid and flow properties, formation thermal properties, and wellbore, tool, and tamp configuration, were also reviewed. The many applications for HEGS were presented. It was emphasized that the success of HEGS is dependent on pre-stimulation problem evaluation and on proper charge design. Since HEGS will decrease near-wellbore restrictions and initiate formation breakdown, it should only be used in cases where this will be beneficial to the well. Careful attention to engineering will optimize results. 21 refs., 13 figs.

  19. Rheology of waxy oils

    Energy Technology Data Exchange (ETDEWEB)

    Alicke, Alexandra A.; Marchesini, Flavio H.; Mendes, Paulo R. de Souza [Pontificia Universidade Catolica do Rio de Janeiro (PUC-Rio), RJ (Brazil)], e-mails: fhmo@puc-rio.br, pmendes@puc-rio.br; Ziglio, Claudio [Petrobras Research Center, Rio de Janeiro, RJ (Brazil)], e-mail: ziglio@petrobras.com.br

    2010-07-01

    It is well known that below the crystallization temperature the rheology of waxy oils changes from Newtonian to an extremely complex non-Newtonian behavior, which is shear-rate and temperature-history dependent. Along the last decades a lot of effort has been put into obtaining reliable rheological measurements from different oils so as to understand the yielding of waxy oils as well as the effects of shear and temperature histories on rheological properties, such as viscosity, yield stress, storage and loss moduli. In this paper we examine in detail the related literature, discussing the main reasons for some disagreements concerning the history effects on the flow properties of waxy oils. In addition, we performed temperature ramps and stress-amplitude-sweep tests and compared the results obtained with the main trends observed, highlighting the effects of cooling and shear on the microstructure and consequently on the rheological properties of these oils. (author)

  20. Essential oils and anxiolytic aromatherapy.

    Science.gov (United States)

    Setzer, William N

    2009-09-01

    A number of essential oils are currently in use as aromatherapy agents to relieve anxiety, stress, and depression. Popular anxiolytic oils include lavender (Lavandula angustifolia), rose (Rosa damascena), orange (Citrus sinensis), bergamot (Citrus aurantium), lemon (Citrus limon), sandalwood (Santalum album), clary sage (Salvia sclarea), Roman chamomile (Anthemis nobilis), and rose-scented geranium (Pelargonium spp.). This review discusses the chemical constituents and CNS effects of these aromatherapeutic essential oils, as well as recent studies on additional essential oils with anxiolytic activities.

  1. Effect of addition of sugar cane biomass ash in properties of fresh state in cement slurries for oil wells; Efeito da adicao de cinza de biomassa de cana-de-acucar nas propriedades no estado fresco de pastas de cimento para pocos de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Galvao, Lornna L.A.; Santos, Herculana T.; Souza, Pablo Diego Pinheiro; Freitas, Julio Cezar Oliveira [Universidade Federal do Rio Grande do Norte (UFRN), RN (Brazil); Nascimento, Julio Cesar S. [Universidade Federal da Bahia (UFBA), BA (Brazil); Amorim, Natalia M.M. [Universidade Potiguar (UNP), RN (Brazil); Martinell, Antonio E. [Mcgill University (MCGILL) (Canada); Universidade Federal do Rio Grande do Norte (UFRN), RN (Brazil)

    2012-07-01

    Recent studies have shown that ashes from biomass, in particular those generated by the alcohol industry have pozzolanic activity and can replace cement in many applications, reducing the consumption of cement and, consequently, the environmental impact caused by the production of this material. The present work evaluated the behavior of ash sugarcane biomass partially replacing Portland cement in concentrations of 10, 20 and 40% BWOC in oil well slurries. The results of rheology, thickening time and stability showed that the addition of 40% of biomass ash in oil well slurries significantly improves their properties, enabling the replacement of cement by ash. (author)

  2. Hanford wells

    International Nuclear Information System (INIS)

    McGhan, V.L.; Myers, D.A.; Damschen, D.W.

    1976-03-01

    The Hanford Reservation contains about 2100 wells constructed from pre-Hanford Works to the present. As of Jan. 1976, about 1800 wells still exist, 850 of which were drilled to the groundwater table; 700 still contain water. This report provides the most complete documentation of these wells and supersedes all previous compilations, including BNWL-1739

  3. Oil risk in oil stocks

    NARCIS (Netherlands)

    Scholtens, Bert; Wang, L

    2008-01-01

    We assess the oil price sensitivities and oil risk premiums of NYSE listed oil & gas firms' returns by using a two-step regression analysis under two different arbitrage pricing models. Thus, we apply the Fama and French (1992) factor returns in a study of oil stocks. In all, we find that the return

  4. Chemical Equilibrium and Mineral Saturation in Waters from Oil Wells of the Activo Luna Field, Tabasco, Mexico; Equilibrio quimico y grado de saturacion de minerales en aguas de pozos petroleros de Activo Luna, Tabasco, Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Barragan R, Rosa Maria; Arellano G, Victor M.; Portugal M, Enrique; Torres R, Vicente [Instituto de Investigaciones Electricas (Mexico); Torres Alvarado, Ignacio [Universidad Nacional Autonoma de Mexico (Mexico); Ascencio C, Fernando; Martinez A; Ana E [Petroleos Mexicanos (Mexico)

    2001-09-01

    Chemical equilibrium of formation waters from seven oil wells of the Activo Luna field (Tabasco, Mexico) was modelled. Saturation indices of characteristic hydrothermal minerals were calculated at ambient and reservoir conditions in order to predict scaling potential of deep and surface installations. The salinity of waters was found to be in the range from 43,000 (well Escuintle 2) to 250,000 (well Lune 3B) mg/kg as total dissolved solids. The water samples were classified as sodium-chioride type. Ionic strength for the solutions was found to be between 0.75 and 6.5. Activity coefficients were estimated by virial (Pitzer equations) methods using the GEOCHEMIST WORKENCH (GWB) software. Minerals such as anhydrite, halite, alunite, fluorite and barite were found to be supersaturated at reservoir conditions. A solid scale sample obtained from well Luna-3B was analysed. Analysis indicate the presence of calcite, anhydrite, fluorite and sphalerite which suggest the occurrence of temperatures of at least 180 Celcius degrees with acidic conditions and high chemical corrosion potential. [Spanish] Se modelo el equilibrio quimico de aguas de formacion producidas por siete pozos petroleros pertenecientes al Activo Luna, en el estado de Tabasco, Mexico, se calcularon los indices de saturacion de minerales caracteristicos tanto en las condiciones ambiente como en las de yacimiento, con el proposito de apoyar el control de incrustaciones en las instalaciones superficiales y profundas. La salinidad de las salmueras se encontro en el rango de 43,000 (pozos Escuintle 2) a 250,000 (pozos Luna 3B) mg/kg de solidos disueltos totales y las muestras se clasificaron como del tipo clorurado-sodico. La fuerza ionica de las soluciones varia entre 0.75 y 6.5 molar, por lo que los coeficientes de actividad de la modelacion de equilibrio quimico se estimaron por metodos viriales empleando las ecuaciones de Pitzer mediante el programa GEOCHEMIST WORKBENCH (GWB). Minerales como anhidrita, halita

  5. Exploring the undulating plateau: the future of global oil supply.

    Science.gov (United States)

    Jackson, Peter M; Smith, Leta K

    2014-01-13

    In this paper, we analyse the factors that will influence long-term oil supply and describe the future form of the global oil supply profile as an 'undulating plateau' rather than an irreversible, short-term peak or an ever upward trend of increasing production. The ultimate transition from a world of relatively plentiful and cheap oil to one of tight supply and high cost will be slow and challenging. An understanding of the signposts for the future path of supply and the drivers of that profile will be critical to managing the transition. The ultimate form of the global supply curve may well be dictated by demand evolution rather than a limited resource endowment in the longer term. Several factors will probably control future global oil supply. We believe that the scale of global oil resource will not constitute a physical supply limit for at least the next two or three decades. However, all categories of oil resources are already more expensive to develop than in the past, requiring high oil prices to stimulate supply growth. Lower rates of oil demand growth relative to economic growth, combined with more challenging supply growth, will probably lead to an undulating plateau sometime after 2040, with demand from non-Organization for Economic Cooperation and Development states continuing to dominate. Upstream investment requirements and oil price volatility will increase towards and beyond the undulating production plateau. In this new world, high oil prices will induce demand destruction, fuel substitution and ever increasing energy efficiency. As we discuss below, the fundamental differences between the IHS Cambridge Energy Research Associates' (IHS CERA) view of the future of oil supply and many peak oil supply models are the timing of the onset of a dramatic slowdown in the rate of growth of supply and the existence or otherwise of a production plateau. We do not dispute that supply will plateau and eventually fall; the question is when, how and at what price

  6. Modern methods of drilling wells by large diameter bits and possible fields of application

    Energy Technology Data Exchange (ETDEWEB)

    Arnold, W

    1970-04-01

    For the needs of up-to-date mining in construction of shafts and mining installations, large diameter wells are often used. In the near future, application of this type of well will be of great importance in the oil industry for stimulation of oil and gas recovery by atomic explosion. Such wells can be used for mineral extraction from subsea and other accessible deposits. The presented state of drilling techniques and technology by large diameter bits is described and similarities and differences with deep-well drilling are pointed out. Some economical data indicate the advantage of drilling by large-diameter bits in comparison with standard methods of construction of shafts and mining installations.

  7. Greater oil investment opportunities

    International Nuclear Information System (INIS)

    Arenas, Ismael Enrique

    1997-01-01

    Geologically speaking, Colombia is a very attractive country for the world oil community. According to this philosophy new and important steps are being taken to reinforce the oil sector: Expansion of the exploratory frontier by including a larger number of sedimentary areas, and the adoption of innovative contracting instruments. Colombia has to offer, Greater economic incentives for the exploration of new areas to expand the exploratory frontier, stimulation of exploration in areas with prospectivity for small fields. Companies may offer Ecopetrol a participation in production over and above royalties, without it's participating in the investments and costs of these fields, more favorable conditions for natural gas seeking projects, in comparison with those governing the terms for oil

  8. Oil shale technology

    International Nuclear Information System (INIS)

    Lee, S.

    1991-01-01

    Oil shale is undoubtedly an excellent energy source that has great abundance and world-wide distribution. Oil shale industries have seen ups and downs over more than 100 years, depending on the availability and price of conventional petroleum crudes. Market forces as well as environmental factors will greatly affect the interest in development of oil shale. Besides competing with conventional crude oil and natural gas, shale oil will have to compete favorably with coal-derived fuels for similar markets. Crude shale oil is obtained from oil shale by a relatively simple process called retorting. However, the process economics are greatly affected by the thermal efficiencies, the richness of shale, the mass transfer effectiveness, the conversion efficiency, the design of retort, the environmental post-treatment, etc. A great many process ideas and patents related to the oil shale pyrolysis have been developed; however, relatively few field and engineering data have been published. Due to the vast heterogeneity of oil shale and to the complexities of physicochemical process mechanisms, scientific or technological generalization of oil shale retorting is difficult to achieve. Dwindling supplied of worldwide petroleum reserves, as well as the unprecedented appetite of mankind for clean liquid fuel, has made the public concern for future energy market grow rapidly. the clean coal technology and the alternate fuel technology are currently of great significance not only to policy makers, but also to process and chemical researchers. In this book, efforts have been made to make a comprehensive text for the science and technology of oil shale utilization. Therefore, subjects dealing with the terminological definitions, geology and petrology, chemistry, characterization, process engineering, mathematical modeling, chemical reaction engineering, experimental methods, and statistical experimental design, etc. are covered in detail

  9. Effects of olive scale (Parlatoria oleae (Colvée attack on yield, quality and fatty acid profile of virgin olive oil

    Directory of Open Access Journals (Sweden)

    M. Krapac

    2014-01-01

    Full Text Available Olive scale (Parlatoria oleae (Colvée is a common pest in Mediterranean olive orchards which primarily causes damage on olive fruits. The quality of virgin olive oil is strongly related to the health status of the olive fruits from which is extracted. In this paper the effects of olive scale (Parlatoria oleae (Colvée attack on the oil yield, chemical and sensorial quality, as well as on the fatty acid profile of virgin olive oil were studied. Olive fruits (Olea europea L. from Bova cultivar (Istria, Croatia were collected and divided into different groups according to the presence or absence of infestation by the olive scale. Olive scale attack did not induce ripening process nor stimulate oil synthesis in the infested fruits. Healthy and infested fruit groups were processed separately to produce corresponding olive oils. As regards the oil acidity, the oil samples obtained from infested fruits had similar values as samples obtained from healthy fruits. However, olive scale attack led to slight oxidative deterioration of oil, but had no effect on sensory characteristics of obtained olive oils. Fatty acid profile was slightly affected by olive scale attack: an increase of linoleic (about 13 % and palmitoleic acid (about 8 %, but a decrease of oleic (about 3 % and stearic acid (about 4 % in oils obtained from infested fruits was detected. Oleic to linoleic ratio was lower in oils obtained from infested fruits indicating its lower oxidative stability.

  10. Compositional modification of crude oil during oil recovery

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Yangming; Weng, Huanxin [Department of Earth Sciences, Zhejiang University, Hangzhou 310027 (China); Chen, Zulin; Chen, Qi [Petroleum Geochemistry Research Center, Jianghan Petroleum University, Jingzhou, Hubei (China)

    2003-05-01

    Ten crude oils from two recovery stages spanning 5-10-year interval of five productive wells in the Tarim Basin, northwest China were analyzed for their compositional modification during production process. Significant compositional changes in polar and nonpolar fractions between the previous oil samples and the latter ones were noted at both bulk and molecular level. The latter oil samples appear to contain more aromatic fraction and less asphaltenes and resin, and their gas chromatography (GC) data for whole oil show reduced alkanes with low molecular weight and enhanced high homologue relative to the previous oil samples. Compared with the oils collected from the previous recovery stage, the concentration of basic type of nitrogen-containing compounds and organic acids in oils from the latter recovery stage have a reducing trend, suggesting the occurrence of interaction between crude oil and reservoir rock.

  11. Desenvolvimento de fluidos aquosos com bentonita para perfuração de poços de petróleo onshore Development of aqueous fluids with bentonite clay for drilling of onshore oil wells

    Directory of Open Access Journals (Sweden)

    R. C. A. M Nascimento

    2010-06-01

    Full Text Available Devido aos grandes desafios encontrados na perfuração de poços, há a necessidade de se desenvolver fluidos com propriedades adequadas e capazes de atender todas as exigências da perfuração, como elevada capacidade de carreamento de sólidos e alta lubricidade, como também fluidos ambientalmente corretos. O grau de impacto dos fluidos de perfuração no meio ambiente depende especialmente do tipo de fluido utilizado, se de base aquosa, oleosa, sintética ou mesmo de base ar. Portanto, é de fundamental importância o desenvolvimento de fluidos com características específicas em cada etapa da perfuração. Sendo assim, este trabalho objetivou o desenvolvimento de fluidos aquosos, com baixo teor de sólidos e propriedades reológicas, de filtração e lubricidade adequadas à perfuração de poços de petróleo onshore. Os fluidos foram formulados utilizando em sua composição bentonita sódica industrializada, aditivos poliméricos e lubrificantes, em diferentes concentrações. O estudo reológico, de filtração e lubricidade mostrou que os fluidos apresentam comportamento pseudoplástico e que os aditivos selecionados desempenham com êxito suas funções de modificadores reológicos, redutores de filtrado e agente lubrificante. Além disto, ficou evidenciada a necessidade de aditivos lubrificantes em fluidos aquosos contendo argila bentonítica e polímeros. A adição de 1% de lubrificante no fluido é suficiente para adequar a capacidade lubrificante dos fluidos.Due to challenges encountered in drilling wells, there is a need to develop fluids that have properties suitable and able to meet all the requirements of drilling, such as, high capacity for carrying of solid and high lubricity. Besides that, they need to be environmentally friend. The degree of impact of drilling fluids in the environment depends on the type of fluid used, if water or oil or synthetic or air based. It is therefore of fundamental importance to develop

  12. Behaviour of a new material for the oil well cementing. Relations between particle structure and rheological properties; Comportement d'un nouveau materiau pour la cimentation de puits de petrole. Relations entre la structure particulaire et les proprietes rheologiques

    Energy Technology Data Exchange (ETDEWEB)

    Dubois, N

    1999-12-16

    This work focuses on the control and the characterization of the rheological behaviour of Ultra High Performances Concretes (UHPC) for oil well during the dormant period, in the first moments following malaxation. Cement, sand, silica fume, water and a super-plasticizer were principally used in this study. We sought to control their rheological behaviour with simple macroscopic data, such as dry compactness and diameters of the particles. Viscosity and yield stress measurements were determined with controlled stress or controlled rotational speed viscosimeters, by using parallel plates, concentric cylinders, or a vane. We highlight the experimental difficulties generated by the characterization of such mixtures and describe the precautions to take in order to carry out significant measurements. First, we explain the rheological behaviour by traditional granular interactions, such as wall and loosening effects. These interactions allow to predict dry compactness and the rheological behaviour of certain granular mixtures, whose diameters ratio of two successive classes n-1 and n satisfies D{sub n-1}/D{sub n}<0,2 with D{sub n}>D{sub n-1}. The introduction of another concept, named 'spacing', enabled us to evaluate the viscosity of suspension whose diameters ratio of two successive size ranges are large (D{sub n-1}/D{sub n}>0,2), and to predict the behaviour of hollow mixtures. We show moreover that it is possible to lower the viscosity and the yield stress of BUHP, by modifying the granulometric distribution of the components, while preserving the same quantity of water. Finally we highlight the particular action of the silica fume, consisted of welded spherical particles and forming not easily breakable clusters, onto the rheological behaviour of BUHP. (author)

  13. Behaviour of a new material for the oil well cementing. Relations between particle structure and rheological properties; Comportement d'un nouveau materiau pour la cimentation de puits de petrole. Relations entre la structure particulaire et les proprietes rheologiques

    Energy Technology Data Exchange (ETDEWEB)

    Dubois, N.

    1999-12-16

    This work focuses on the control and the characterization of the rheological behaviour of Ultra High Performances Concretes (UHPC) for oil well during the dormant period, in the first moments following malaxation. Cement, sand, silica fume, water and a super-plasticizer were principally used in this study. We sought to control their rheological behaviour with simple macroscopic data, such as dry compactness and diameters of the particles. Viscosity and yield stress measurements were determined with controlled stress or controlled rotational speed viscosimeters, by using parallel plates, concentric cylinders, or a vane. We highlight the experimental difficulties generated by the characterization of such mixtures and describe the precautions to take in order to carry out significant measurements. First, we explain the rheological behaviour by traditional granular interactions, such as wall and loosening effects. These interactions allow to predict dry compactness and the rheological behaviour of certain granular mixtures, whose diameters ratio of two successive classes n-1 and n satisfies D{sub n-1}/D{sub n}<0,2 with D{sub n}>D{sub n-1}. The introduction of another concept, named 'spacing', enabled us to evaluate the viscosity of suspension whose diameters ratio of two successive size ranges are large (D{sub n-1}/D{sub n}>0,2), and to predict the behaviour of hollow mixtures. We show moreover that it is possible to lower the viscosity and the yield stress of BUHP, by modifying the granulometric distribution of the components, while preserving the same quantity of water. Finally we highlight the particular action of the silica fume, consisted of welded spherical particles and forming not easily breakable clusters, onto the rheological behaviour of BUHP. (author)

  14. Live Well

    Science.gov (United States)

    ... Health Conditions Live Well Mental Health Substance Use Smoking Healthy Diet Physical Activity Family Planning Living with HIV: Travel ... to his or her health and well-being. Smoking - Tobacco use is the ... year. Healthy Diet - No matter your HIV status, healthy eating is ...

  15. The asymmetric relationship between oil revenues and economic activities: The case of oil-exporting countries

    International Nuclear Information System (INIS)

    Mehrara, Mohsen

    2008-01-01

    This paper examines the nonlinear or asymmetric relationship between oil revenues and output growth in oil-exporting countries, applying a dynamic panel framework and two different measures of oil shocks. The main results in this paper confirm the stylized facts that in heavily oil-dependent countries lacking the institutional mechanisms de-linking fiscal expenditure from current revenue, oil revenue shocks tend to affect the output in asymmetric and nonlinear ways. The findings suggest that output growth is adversely affected by the negative oil shocks, while oil booms or the positive oil shocks play a limited role in stimulating economic growth. The findings have practical policy implications for decision makers in the area of macroeconomic planning. The use of stabilization and savings funds and diversification of the real sector seems crucial to minimize the harmful effects of oil booms and busts

  16. Hanford wells

    International Nuclear Information System (INIS)

    Chamness, M.A.; Merz, J.K.

    1993-08-01

    Records describing wells located on or near the Hanford Site have been maintained by Pacific Northwest Laboratory and the operating contractor, Westinghouse Hanford Company. In support of the Ground-Water Surveillance Project, portions of the data contained in these records have been compiled into the following report, which is intended to be used by those needing a condensed, tabular summary of well location and basic construction information. The wells listed in this report were constructed over a period of time spanning almost 70 years. Data included in this report were retrieved from the Hanford Envirorunental Information System (HEIS) database and supplemented with information not yet entered into HEIS. While considerable effort has been made to obtain the most accurate and complete tabulations possible of the Hanford Site wells, omissions and errors may exist. This document does not include data on lithologic logs, ground-water analyses, or specific well completion details

  17. Gas coning control for smart wells using a dynamic coupled well-reservoir simulator

    NARCIS (Netherlands)

    Leemhuis, A.P.; Nennie, E.D.; Belfroid, S.P.C.; Alberts, G.J.N.; Peters, E.; Joosten, G.J.P.

    2008-01-01

    A strong increase in gas inflow due to gas coning and the resulting bean-back because of Gas to Oil Ratio (GOR) constraints can severely limit oil production and reservoir drive energy. In this paper we will use a coupled reservoir-well model to demonstrate that oil production can be increased by

  18. Manitoba oil activity review, 1991

    International Nuclear Information System (INIS)

    1992-04-01

    In an annual survey of Manitoba's petroleum industry, data are presented on oil and natural gas leases and sales, geophysical activity, exploration and drilling activity, production, exports to other provinces and the USA, oil prices and sales value, royalties and taxes, direct revenues from oil exploration and development, reserves, industry expenditures, and oil fields. Throughout the report, explainations are given of the items covered. Descriptions are made of new developments, the oil market, oil policies, incentive programs, and industrial activities. During 1991, 54 wells were drilled, compared to 79 in 1990. Oil production was down ca 3% from 1990 levels, to 712,792 m 3 , the value of the oil produced decreased 21% to ca $90.3 million, and provincial revenues from the oil industry declined by 15%. Oil industry expenditures in the province were estimated at $69 million, down 9% from 1990. As of the end of 1991, there were 11 oil fields and 118 non-confidential oil pools designated in Manitoba. The forecast for 1992 indicates that exploration activity will increase in response to new incentive programs. Crude oil production is expected to decline slightly to about 667,000 m 3 . 9 figs., 17 tabs

  19. Heavy oil and bitumen : thinking caps on : researchers look at new and greener ways to get at the heavy oil prize

    Energy Technology Data Exchange (ETDEWEB)

    Harrison, L.

    2008-01-15

    New steam stimulation processes developed by the Alberta Ingenuity Centre for In Situ Energy were discussed. The J-well and gravity-assisted steam stimulation (JAGD) process uses a steam injection well located within the top few metres of a reservoir and a production well comprised of an inclined J-shaped well. JAGD is a transitional cold production-to-thermal-production technology. High pressure steam is used to heat and loosen the bitumen so that it flows to the producer well below. The configuration was designed to cut through mud and shale layers and is suitable for poor quality reservoirs. Simulations conducted in Athabasca reservoirs have demonstrated that JAGD uses approximately 75 per cent of the steam typically used in steam assisted gravity drainage (SAGD) processes. The iSAGD process was designed to reposition parallel wells in order to increase oil mobility. Researchers at the centre are also investigating a catalytic air-stream process called CASPAR which aims to upgrade oil from 10 degrees API to 16 degrees API within the reservoir. The process involves a mixture of heat, catalyst hydrogen, steam, air and water in the reservoir. The process leaves heavier ends of oil underground as well as fractions of greenhouse gases (GHGs). Research is also being conducted on expanding-solvent SAGD (ES-SAGD) a process that adds butane to steam in order to reduce water use. 3 figs.

  20. Lavender oil

    Science.gov (United States)

    Lavender oil is an oil made from the flowers of lavender plants. Lavender poisoning can occur when ... further instructions. This is a free and confidential service. All local poison control centers in the United ...

  1. Petroleum Oils

    Science.gov (United States)

    Different types of crude oil and refined product, of all different chemical compositions, have distinct physical properties. These properties affect the way oil spreads and breaks down, its hazard to marine and human life, and the likelihood of threat.

  2. Viscous fingering effects in solvent displacement of heavy oil

    Energy Technology Data Exchange (ETDEWEB)

    Cuthiell, D. [Suncor Energy, Fort McMurray, AB (Canada); Kissel, G.; Jackson, C.; Frauenfeld, T.W.J.; Fisher, D. [Alberta Research Council, Devon, AB (Canada); Rispler, K. [Saskatchewan Research Council, Saskatoon, SK (Canada)

    2004-07-01

    Vapour Extraction (VAPEX) is a solvent-based process that is analogous to steam-assisted gravity drainage (SAGD) for the recovery of heavy oil. A cyclic solvent process is preferred for thin reservoirs, particularly primary-depleted reservoirs. In a cyclic steam stimulation process, a solvent is injected into the reservoir for a period of time before oil is produced from the well. Viscous fingering is a phenomena that characterizes several solvent-based processes for the recovery of heavy oil. A combined experimental and simulation study was conducted to characterize viscous fingering under heavy oil recovery conditions (high ratio of oil to solvent viscosity). Four experiments were conducted in heavy oil-saturated sand packs. Three involved injection of a miscible, liquid solvent at the bottom of the sand pack. The heavy oil in these experiments was displaced upwardly. The fourth experiment involved top-down injection of a gaseous solvent. The miscible liquid displacement was dominated by one solvent finger which broke through to a producing well at the other end of the sand pack. Breakthrough times were similar to that at lower viscosity. The fourth experiment showed fingering along with features of a gravity-driven VAPEX process. Key features of the experiment and realistic fingering patterns were numerically simulated using a commercial reservoir simulator. It was emphasized that accurate modelling of dispersion is necessary in matching the observed phenomena. The simulations should include the capillary effects because of their significance for gaseous fingering and the VAPEX processes. 17 refs., 2 tabs., 20 figs.

  3. Nanoparticles usage tendencies in cementing systems for hydrocarbon wells

    NARCIS (Netherlands)

    Balza, A.; Perera, Y.; Brito, J.; Hurtado, A.; Quercia Bianchi, G.; Corona, O.; Colina, A.; Blanco, A.; Palomo, A.; Zaragoza, A.; Lopez, J.C.

    2011-01-01

    In oil and gas wells construction, one of the most critical processes is oil well cementing, whose function is to provide a zonal isolation between the pipe and sedimentary formation. For these reasons, one of the needs in the oil industry, specifically in cementing wells area, is the use of

  4. Oil sands supply outlook

    International Nuclear Information System (INIS)

    Dunbar, R.

    2004-01-01

    In March 2004, The Canadian Energy Research Institute released a report on the expected future supply from Alberta's oil sands. The report indicates that the future for the already well-established oil sands industry is promising, particularly given the outlook for oil prices. The challenges facing the industry include higher industry supply costs and the need for innovative commercial and technological solutions to address the risks of irregularities and changes in crude oil prices. In 2003, the industry produced 874 thousand barrels per day of synthetic crude oil and unprocessed crude bitumen. This represents 35 per cent of Canada's total oil production. Current production capacity has increased to 1.0 million barrels per day (mbpd) due to new projects. This number may increase to 3.5 mbpd by 2017. Some new projects may be deferred due to the higher raw bitumen and synthetic crude oil supply costs. This presentation provided supply costs for a range of oil sands recovery technologies and production projections under various business scenarios. tabs., figs

  5. Oxidative stability of diacylglycerol oil and butter blends containing diacylglycerols

    DEFF Research Database (Denmark)

    Kristensen, Janni Brogaard; Nielsen, Nina Skall; Jacobsen, Charlotte

    2006-01-01

    Diacylglycerol (DAG) oils produced from sunflower oil and traditional sunflower oil were stored for 20 wk at 38 degrees C, and their oxidative stability was measured. Moreover, two butter blends were produced containing 40 wt-% DAG oil made from sunflower oil or rapeseed oil, respectively, as well...... as two control butter blends with sunflower oil or rapeseed oil. Their oxidative stability during storage at 5 degrees C for up to 12 wk was examined by similar means as for the pure oils. The storage study of the oils indicated that the DAG oil was oxidatively less stable as compared to sunflower oil......, but that they had similar sensory quality. Storage of the butter blends revealed that blends with the two types of rapeseed oil (triacylglycerol (TAG) or DAG oil) were oxidatively more stable than the blends containing oils from sunflower. There was no unambiguous indication of DAG butter blends having a different...

  6. Militantly Well

    DEFF Research Database (Denmark)

    Vigh, Henrik Erdman

    2015-01-01

    futures that transcend conflict engagement and wartime suffering for young militiamen. It clarifies the positive prospects that are expected to lie beyond the known horrors of war. Though conflict and warfare may provide strange points of departure for talking about well-being, imaginaries of happiness...... stand out from a background of hardship and are talked about in both a quite concrete way, as a lack of insecurity, as well as in an abstract way, as realization of social being. However, for most of the people I talk to, happiness remains elusive and evades their desperate attempts to grasp it...

  7. Thermally-enhanced oil recovery method and apparatus

    Science.gov (United States)

    Stahl, Charles R.; Gibson, Michael A.; Knudsen, Christian W.

    1987-01-01

    A thermally-enhanced oil recovery method and apparatus for exploiting deep well reservoirs utilizes electric downhole steam generators to provide supplemental heat to generate high quality steam from hot pressurized water which is heated at the surface. A downhole electric heater placed within a well bore for local heating of the pressurized liquid water into steam is powered by electricity from the above-ground gas turbine-driven electric generators fueled by any clean fuel such as natural gas, distillate or some crude oils, or may come from the field being stimulated. Heat recovered from the turbine exhaust is used to provide the hot pressurized water. Electrical power may be cogenerated and sold to an electric utility to provide immediate cash flow and improved economics. During the cogeneration period (no electrical power to some or all of the downhole units), the oil field can continue to be stimulated by injecting hot pressurized water, which will flash into lower quality steam at reservoir conditions. The heater includes electrical heating elements supplied with three-phase alternating current or direct current. The injection fluid flows through the heater elements to generate high quality steam to exit at the bottom of the heater assembly into the reservoir. The injection tube is closed at the bottom and has radial orifices for expanding the injection fluid to reservoir pressure.

  8. Alternatives to OPEC oil

    International Nuclear Information System (INIS)

    Johnson, C.

    1981-01-01

    This paper starts from the assumption that, for various reasons, the supply of OPEC oil required to meet a rising world energy demand will continue to be limited. Its purpose is to present a synoptic look at the various sources of energy which are alternatives to OPEC oil, with an economic commentary on the prospects for each source. A wide variety of projects are going forward for the development of non-OPEC oil, gas, coal, and nuclear power, as well as renewable energy resources. Special attention is devoted to questions of energy pricing, investment costs, and sources of finance. (author)

  9. Ozonated Olive Oils and Troubles

    Directory of Open Access Journals (Sweden)

    Bulent Uysal

    2014-04-01

    Full Text Available One of the commonly used methods for ozone therapy is ozonated oils. Most prominent type of used oils is extra virgin olive oil. But still, each type of unsaturated oils may be used for ozonation. There are a lot of wrong knowledge on the internet about ozonated oils and its use as well. Just like other ozone therapy studies, also the studies about ozone oils are inadequate to avoid incorrect knowledge. Current data about ozone oil and its benefits are produced by supplier who oversees financial interests and make misinformation. Despite the rapidly increasing ozone oil sales through the internet, its quality and efficacy is still controversial. Dozens of companies and web sites may be easily found to buy ozonated oil. But, very few of these products are reliable, and contain sufficiently ozonated oil. This article aimed to introduce the troubles about ozonated oils and so to inform ozonated oil users. [J Intercult Ethnopharmacol 2014; 3(2.000: 49-50

  10. Fluid diversion in oil recovery

    International Nuclear Information System (INIS)

    Nimir, Hassan B.

    1999-01-01

    In any oil recovery process, large scale heterogeneities, such as fractures, channels, or high-permeability streaks, can cause early break through of injected fluid which will reduce oil recovery efficiency. In waterflooding, enhanced oil recovery, and acidizing operations, this problem is particularly acute because of the cost of the injected fluid. On the other hand coping with excess water production is always a challenging task for field operators. The cost of handling and disposing produced water can significantly shorten the economic production life of an oil well. The hydrostatic pressure created by high fluid levels in a well (water coning) is also detrimental to oil production. In this paper, the concept of fluid diversion is explained. Different methods that are suggested to divert the fluid into the oil-bearing-zones are briefly discussed, to show their advantages and disadvantages. Methods of reducing water production in production well are also discussed. (Author)

  11. Alberta oil sands crudes : upgrading and marketing

    International Nuclear Information System (INIS)

    Ashar, M.

    2008-01-01

    Open pit mining and in situ techniques, such as steam stimulation, are used to recover Alberta's bitumen and heavy oil resources, which have higher viscosities than conventional hydrocarbons. The bitumen is typically upgraded to synthetic crude oil (SCO). In the simplest processing scheme, the bitumen is blended with diluent for ease in pipeline transport and then processed at refineries with upgrading facilities. The bitumen is also upgraded to light SCO at world-scale upgraders in Alberta. The SCO is then processed at refineries in downstream markets. The 2 categories of upgrading, notably primary and secondary upgrading, were described in this article along with technology options for both categories. Slurry hydrocracking is regarded as the most interesting emerging residual fuel upgrading technology. It combines special catalyst mixes with the latest slurry reactor designs as well as innovative catalyst capture and recycle schemes to produce very high conversions and potentially superior upgrading economics. The increase in volume and rate of SCO from Alberta provides refiners in the oil sands marketing sector an unprecedented choice of opportunities to improve profitability. Key trends indicate that production will increase substantially from 2008 to 2030. 5 figs

  12. Alberta oil sands crudes : upgrading and marketing

    Energy Technology Data Exchange (ETDEWEB)

    Ashar, M. [Suncor Energy, Fort McMurray, AB (Canada)

    2008-05-15

    Open pit mining and in situ techniques, such as steam stimulation, are used to recover Alberta's bitumen and heavy oil resources, which have higher viscosities than conventional hydrocarbons. The bitumen is typically upgraded to synthetic crude oil (SCO). In the simplest processing scheme, the bitumen is blended with diluent for ease in pipeline transport and then processed at refineries with upgrading facilities. The bitumen is also upgraded to light SCO at world-scale upgraders in Alberta. The SCO is then processed at refineries in downstream markets. The 2 categories of upgrading, notably primary and secondary upgrading, were described in this article along with technology options for both categories. Slurry hydrocracking is regarded as the most interesting emerging residual fuel upgrading technology. It combines special catalyst mixes with the latest slurry reactor designs as well as innovative catalyst capture and recycle schemes to produce very high conversions and potentially superior upgrading economics. The increase in volume and rate of SCO from Alberta provides refiners in the oil sands marketing sector an unprecedented choice of opportunities to improve profitability. Key trends indicate that production will increase substantially from 2008 to 2030. 5 figs.

  13. Global oil company profiles

    International Nuclear Information System (INIS)

    1997-01-01

    Global Oil Company Profiles provides a comprehensive review of 50 of the top oil companies in the world. Each chapter is devoted to an individual company, providing an invaluable insight into the organisation, its structure and operations. Using the most recent data available, the report offers an up-to-date analysis of performance and future direction, as well as a unique benchmarking system for each company profiled. (author)

  14. Biotransformation of natural gas and oil compounds associated with marine oil discharges.

    Science.gov (United States)

    Brakstad, Odd Gunnar; Almås, Inger K; Krause, Daniel Franklin

    2017-09-01

    Field data from the Deepwater Horizon (DWH) oil spill in the Gulf of Mexico (GoM) suggested that oxidation of gas compounds stimulated biodegradation of oil compounds in the deep sea plume. We performed experiments with local seawater from a Norwegian fjord to examine if the presence of dissolved gas compounds (methane, ethane and propane) affected biodegradation of volatile oil compounds, and if oil compounds likewise affected gas compound oxidation. The results from the experiment showed comparable oil compound biotransformation rates in seawater at 5 °C between seawater with and without soluble gases. Gas oxidation was not affected by the presence of volatile oil compounds. Contrary to DWH deep sea plume data, propane oxidation was not faster than methane oxidation. These data may reflect variations between biodegradation of oil and gas in seawater environments with different history of oil and gas exposure. Copyright © 2017 Elsevier Ltd. All rights reserved.

  15. Radioisotope techniques for problem solving in the offshore oil and gas industry

    International Nuclear Information System (INIS)

    Charlton, J.S.; Hurst, J.A.

    1994-01-01

    Radioisotope technology has been used for almost half a century by the oil and gas industry to solve problems and to help optimize process operations. The use of radioactive isotopes to investigate the effectiveness of well stimulation procedures and to measure the sweep-out patterns of oil and gas in secondary recovery process is well known. The applications of radioisotopes to study features of plant and process operation has been less widely reported though the economic benefits deriving from such applications are very great. Nevertheless, there has been continuous development in the range of application and in the design of equipment to facilitate the use of the technology at remote environments such as an oil or gas platform. Some indication of the current usage of radioisotope techniques may be obtained from examination of Table I, which lists projects carried out in the UK's North Sea fields by ICI Tracerco, which is the world's largest radioisotope applications service group

  16. Wellness centrum

    OpenAIRE

    Krchňák, Petr

    2016-01-01

    Diplomová práce „Wellness centrum'' je zpracována ve formě prováděcí dokumentace obsahující všechny náležitosti dle platných norem a předpisů. Navržený objekt je řešen jako třípodlažní budova. Objekt slouží veřejnosti k rekreaci a sportu. V 1S je umístěno technické zázemí, zázemí pro zaměstnance, šatny a posilovna. V 1 NP se nachází kavárna a wellness. Ve 2NP se nachází kanceláře pro administrativu budovy, masáže, solárium, šatny a fitness sál. Budova je založena na základových patkách a nosn...

  17. Estimation of Oil Production Rates in Reservoirs Exposed to Focused Vibrational Energy

    KAUST Repository

    Jeong, Chanseok; Kallivokas, Loukas F.; Huh, Chun; Lake, Larry W.

    2014-01-01

    the production rate of remaining oil from existing oil fields. To date, there are few theoretical studies on estimating how much bypassed oil within an oil reservoir could be mobilized by such vibrational stimulation. To fill this gap, this paper presents a

  18. HOW PROPERTIES OF EDIBLE OILS ARE IMPROVED BY ESSENTIAL OILS

    Directory of Open Access Journals (Sweden)

    SONIA AMARIEI

    2016-10-01

    Full Text Available The main aim of the present paper is to find out whether the addition of essential oils determines better oxidation stability and positive change of sensory and hedonic perception of edible oils. The oxidation stability of sunflower, corn and grape seed oils was analyzed in the presence of antioxidants in essential oils of rosemary (Rosmarinus officinalis, thyme (Thymus vulgaris and basil (Ocimum basilicum during storage, under conditions of accelerated oxidative processes (4 days, at 60 °C. The total phenolic compounds of these essential oils were determined by the Folin-Ciocalteu method. The DPPH method was used to evaluate the antioxidant capacity of basil, rosemary and thyme essential oils in comparison with known synthetic antioxidant L(+-ascorbic acid. The addition of essential oils to edible oils, the amounts proposed in analyses, determines a favorable influence on their oxidation stability as well as their taste. The influence of addition of essential oils on the taste of edible oils was studied in two products consumed mainly at breakfast, bread and spinach leaves. The results recommend the use of these plant extracts as additives in edible oils rather than synthetic antioxidants.

  19. The state tax regulation in the oil and gas industry

    Directory of Open Access Journals (Sweden)

    E. I. Cherkasova

    2018-01-01

    Full Text Available Russian tax laws in petrochemical complex generally has a fiscal orientation now. The current system of taxation in the oil industry has the biggest tax burden in the world, amount of oil and gas revenues was more then 43-51% of all budget revenues over past decades, remaining its main source. Generally, there were changes in the ratios of incomes in the forms of export customs duty and tax on the extraction of minerals. State policy in the field of resource payments affects the entire industry, influencing the structure of oil and oil supplies on internal and external markets and realization of the programs for modernization and development in priority areas. Changes of structure of national production, increasing the contribution of agriculture, IT sphere and other branches to aggregate national product should be reflected in the revision of the tax burden on the industries, associated with the extraction and processing of minerals. It is necessary to reduce the fiscal direction of tax regulation in petrochemical sector with a simultaneous increasing the role of tools that stimulate modernization and updating of equipment, implementation of new processes and technologies, the maximum use of process-deepening processes as well as the development of deposits with severe production conditions. In the near future, it is planned to introduce new changes in taxation in field of oil production and refining - introduction of benefits for oil production in new fields or fields with difficult production conditions or poor quality of oil and introduction of a tax on additional income..

  20. Phytoplankton dynamic responses to oil spill in Mumbai Harbour

    Digital Repository Service at National Institute of Oceanography (India)

    JiyalalRam, M.J.; Ram, A.; Rokade, M.A.; Karangutkar, S.H.; Yengal, B.; Dalvi, S.; Acharya, D.; Sharma, S.; Gajbhiye, S.N.

    have shown that the high concen- tration of oil reduces the phytoplankton growth but when oil becomes in low concentration it, stimulates the growth of microalgae [29-31]. Aksmann and Tukaj [32], believed that the reac- tive oxygen free radicals... in phytoplankton cells increased under the stress of oil pollution and such increment of reactive oxygen free radicals promoted the content of superoxide dismutase in cells at low concentrations of oil, which enhanced the defensive reaction of algae cells...

  1. Jojoba oil and derivates

    Energy Technology Data Exchange (ETDEWEB)

    Wisniak, T

    1977-01-01

    Jojoba oil differs from all known seed oils by its almost complete absence of glycerides, making it more a liquid wax than a fat. It has become important as a possible substitute for sperm-whale oil to produce lubricants, lubricant additives and other products. The plant occurs naturally in southern Arizona and N.W. Mexico and its oil has long been used by Indians for medicinal, culinary, ritual and other purposes. It tolerates extreme daily fluctuations of temperature and grows well under the difficult soil and moisture conditions of the region. In the first part of this review the plant and its uses are described, including its floral, fruit and seed anatomy and the use of liquid wax during germination. Stored coryledon wax is used up by the embryo as a linear function of time during the first 30 days of germination and growth. Before germination, seeds weight about 0.59 mg and contain about 54% wax. The second and greater part of the review deals with jojoba oil (its extraction, properties, molecular description, toxicity and composition), jojoba meal, which remains after the oil has been extracted, and the chemical modification of the oil.

  2. Negative/positive chemotaxis of a droplet: Dynamic response to a stimulant gas

    Science.gov (United States)

    Sakuta, Hiroki; Magome, Nobuyuki; Mori, Yoshihito; Yoshikawa, Kenichi

    2016-05-01

    We report here the repulsive/attractive motion of an oil droplet floating on an aqueous phase caused by the application of a stimulant gas. A cm-sized droplet of oleic acid is repelled by ammonia vapor. In contrast, a droplet of aniline on an aqueous phase moves toward hydrochloric acid as a stimulant. The mechanisms of these characteristic behaviors of oil droplets are discussed in terms of the spatial gradient of the interfacial tension caused by the stimulant gas.

  3. Nitrate-Mediated Microbially Enhanced Oil Recovery (N-MEOR) from model upflow bioreactors.

    Science.gov (United States)

    Gassara, Fatma; Suri, Navreet; Voordouw, Gerrit

    2017-02-15

    Microbially Enhanced Oil Recovery (MEOR) can enhance oil production with less energy input and less costs than other technologies. The present study used different aqueous electron donors (acetate, glucose, molasses) and an aqueous electron acceptor (nitrate) to stimulate growth of heterotrophic nitrate reducing bacteria (hNRB) to improve production of oil. Initial flooding of columns containing heavy oil (viscosity of 3400cP at 20°C) with CSBK (Coleville synthetic brine medium) produced 0.5 pore volume (PV) of oil. Bioreactors were then inoculated with hNRB with 5.8g/L of molasses and 0, 10, 20, 40, 60 or 80mM nitrate, as well as with 17mM glucose or 57mM acetate and 80mM nitrate. During incubations no oil was produced in the bioreactors that received 5.8g/L of molasses and 0, 10, 20, 40 or 60mM nitrate. However, the bioreactors injected with 5.8g/L of molasses, 17mM glucose or 57mM acetate and 80mM nitrate produced 13.9, 11.3±3.1 and 17.8±6.6% of residual oil, respectively. The significant production of oil from these bioreactors may be caused by N 2 -CO 2 gas production. Following continued injection with CSBK without nitrate, subsequent elution of significant residual oil (5-30%) was observed. These results also indicate possible involvement of fermentation products (organic acids, alcohols) to enhance heavy oil recovery. Copyright © 2016 Elsevier B.V. All rights reserved.

  4. Utilizing natural gas huff and puff to enhance production in heavy oil reservoir

    Energy Technology Data Exchange (ETDEWEB)

    Wenlong, G.; Shuhong, W.; Jian, Z.; Xialin, Z. [Society of Petroleum Engineers, Kuala Lumpur (Malaysia)]|[PetroChina Co. Ltd., Beijing (China); Jinzhong, L.; Xiao, M. [China Univ. of Petroleum, Beijing (China)

    2008-10-15

    The L Block in the north structural belt of China's Tuha Basin is a super deep heavy oil reservoir. The gas to oil ratio (GOR) is 12 m{sup 3}/m{sup 3} and the initial bubble point pressure is only 4 MPa. The low production can be attributed to high oil viscosity and low flowability. Although steam injection is the most widely method for heavy oil production in China, it is not suitable for the L Block because of its depth. This paper reviewed pilot tests in which the natural gas huff and puff process was used to enhance production in the L Block. Laboratory experiments that included both conventional and unconventional PVT were conducted to determine the physical property of heavy oil saturated by natural gas. The experiments revealed that the heavy oil can entrap the gas for more than several hours because of its high viscosity. A pseudo bubble point pressure exists much lower than the bubble point pressure in manmade foamy oils, which is relative to the depressurization rate. Elastic energy could be maintained in a wider pressure scope than natural depletion without gas injection. A special experimental apparatus that can stimulate the process of gas huff and puff in the reservoir was also introduced. The foamy oil could be seen during the huff and puff experiment. Most of the oil flowed to the producer in a pseudo single phase, which is among the most important mechanisms for enhancing production. A pilot test of a single well demonstrated that the oil production increased from 1 to 2 cubic metres per day to 5 to 6 cubic metres per day via the natural gas huff and puff process. The stable production period which was 5 to 10 days prior to huff and puff, was prolonged to 91 days in the first cycle and 245 days in the second cycle. 10 refs., 1 tab., 12 figs.

  5. Hydrocarbon oils

    Energy Technology Data Exchange (ETDEWEB)

    Foorwood, G F; Taplay, J G

    1916-12-12

    Hydrocarbon oils are hydrogenated, cracked, or treated for the removal of sulfur by bringing their vapors mixed with steam at temperatures between 450 and 600/sup 0/C into contact with a form of carbon that is capable of decomposing steam with the production of nascent hydrogen at those temperatures. The forms of carbon used include lamp-black, soot, charcoals derived from wood, cellulose, and lignite, and carbons obtained by carbonizing oil residues and other organic bodies at temperatures below 600/sup 0/C. The process is applied to the treatment of coal oil, shale oil, petroleum, and lignite oil. In examples, kerosene is cracked at 570/sup 0/C, cracked spirit is hydrogenated at 500/sup 0/C, and shale spirit is desulfurized at 530/sup 0/C. The products are led to a condenser and thence to a scrubber, where they are washed with creosote oil. After desulfurization, the products are washed with dilute caustic soda to remove sulfurretted hydrogen.

  6. Oil crises

    International Nuclear Information System (INIS)

    Linderoth, H.

    1992-01-01

    The author's aim was to give very precise information on the many causes and effects of the oil crises that have occurred since 1900, and at the same time offer the reader the possibility to build up a basic knowledge of the oil industry and market, as he feels that the public is often subjected to misleading information. Political and economical aspects are elaborated. First-hand sources such as statistics and investigations have been used as far as possible to give information on the oil market. An oil crisis is defined by the author as a significant change in the price of oil compared to prices of other goods. Changes can be in the form of either rising or falling prices. A special chapter concentrates on Denmark in relation to the oil crises. (AB) (165 refs.)

  7. Altering Reservoir Wettability to Improve Production from Single Wells

    Energy Technology Data Exchange (ETDEWEB)

    W. W. Weiss

    2006-09-30

    Many carbonate reservoirs are naturally fractured and typically produce less than 10% original oil in place during primary recovery. Spontaneous imbibition has proven an important mechanism for oil recovery from fractured reservoirs, which are usually weak waterflood candidates. In some situations, chemical stimulation can promote imbibition of water to alter the reservoir wettability toward water-wetness such that oil is produced at an economic rate from the rock matrix into fractures. In this project, cores and fluids from five reservoirs were used in laboratory tests: the San Andres formation (Fuhrman Masho and Eagle Creek fields) in the Permian Basin of Texas and New Mexico; and the Interlake, Stony Mountain, and Red River formations from the Cedar Creek Anticline in Montana and South Dakota. Solutions of nonionic, anionic, and amphoteric surfactants with formation water were used to promote waterwetness. Some Fuhrman Masho cores soaked in surfactant solution had improved oil recovery up to 38%. Most Eagle Creek cores did not respond to any of the tested surfactants. Some Cedar Creek anticline cores had good response to two anionic surfactants (CD 128 and A246L). The results indicate that cores with higher permeability responded better to the surfactants. The increased recovery is mainly ascribed to increased water-wetness. It is suspected that rock mineralogy is also an important factor. The laboratory work generated three field tests of the surfactant soak process in the West Fuhrman Masho San Andres Unit. The flawlessly designed tests included mechanical well clean out, installation of new pumps, and daily well tests before and after the treatments. Treatments were designed using artificial intelligence (AI) correlations developed from 23 previous surfactant soak treatments. The treatments were conducted during the last quarter of 2006. One of the wells produced a marginal volume of incremental oil through October. It is interesting to note that the field

  8. Degradation of crude oil by marine cyanobacteria

    Digital Repository Service at National Institute of Oceanography (India)

    Raghukumar, C.; Vipparty, V.; David, J.J.; Chandramohan, D.

    The marine cyanobacteria Oscillatoria salina Biswas, Plectonema terebrans Bornet et Flanhault and Aphanocapsa sp. degraded Bombay High crude oil when grown in artificial seawater nutrients as well as in plain natural seawater. Oil removals...

  9. Wellness hotel

    OpenAIRE

    Bambas, Vratislav

    2013-01-01

    Novostavba Wellness hotelu. Objekt je částečně podsklepen. Hotel se skládá ze tří částí. Střední trakt je železobetonový skelet a má pět nadzemních podlaží. Tato část slouží jako vstupní hala a hlavní schodiště. Boční trakty mají čtyři nadzemní podlaží a jejich nosný systém je příčný stěnový, zděný, ze systému Porotherm. V suterénu se nachází zázemí hotelu a bazén. Do přízemí je umístěno restaurační zařízení. Ve druhém patře se nacházejí pokoje, posilovna a služby. V posledním patře jsou pouz...

  10. Well acidizing

    Energy Technology Data Exchange (ETDEWEB)

    Street, E H

    1980-01-23

    The apparatus relates in particular to a well-treating process in which an aqueous acid solution having a pH of < 2 is injected into a subterranean reservoir in a manner such that materials that contain ferric ions are present in the acid and, as the acid reacts within the reservoir and attains a pH exceeding 3, tend to be precipitated as ferric ion-containing solid materials that may plug the pores of the reservoir. Such a precipitation is prevented by dissolving in the acid solution an amount of 5-sulfosalicylic acid which is at least sufficient to sequester significant proportions of ferric ions when the pH of the acid is from 0.5 to 3 but is less than enough to cause a significant salting-out of solid materials, and an amount of citric acid which is at least sufficient to sequester significant proportions of ferric ions when the pH of the acid is from 3 to 6 but is less than enough to precipitate a significant amount of calcium citrate. The amount of the 5-sulfosalicylic acid may be from 0.01 to 0.05 moles/l and the amount of citric acid is from 0.001 to 0.009 moles/l. 11 claims.

  11. Quality control of mixtures consisting of engine oil and rapeseed oil by means of online oil sensors; Qualitaetsueberwachung von Motoroel-Rapsoelmischungen mit Online-Oelsensoren. Labortests

    Energy Technology Data Exchange (ETDEWEB)

    Thuneke, Klaus; Schreiber, Katja [Technologie- und Foerderzentrum, Straubing (Germany)

    2013-10-01

    It was the goal of the work to investigate interactions between motor oils and rapeseed oil fuel and to test oil sensors for monitoring the quality of aged mixtures of motor oil and rapeseed oil. At first oil samples were aged in the laboratory, whereby motor oil type, share of rapeseed oil and aeration was varied. Depending on type of engine oil different ageing effects were noticed. Higher shares of rapeseed and aeration stimulate increase of viscosity and acid value. In a further step online oil sensors were tested in both, a model of a lubrication system and a test engine. The signals of the sensors plausibly described the oil ageing process by the indicators dynamic or acoustic viscosity, permittivity number, specific electric conductivity. In particular viscosity and permittivity are suitable for showing changes in different motor oil rapeseed oil mixtures during oil ageing. However, for a reliable control system detecting critical rapeseed oil enrichment in the motor oil onboard, further work has to be done. (orig.)

  12. Oil pollution

    International Nuclear Information System (INIS)

    Mankabady, Samir.

    1994-08-01

    Oil enters the marine environment when it is discharged, or has escaped, during transport, drilling, shipping, accidents, dumping and offshore operations. This book serves as a reference both on the various complex international operational and legal matters of oil pollution using examples such as the Exxon Valdez, the Braer and Lord Donaldson's report. The chapters include the development of international rules on the marine environment, the prevention of marine pollution from shipping activities, liability for oil pollution damage, the conflict of the 1990 Oil Pollution Act and the 1992 protocols and finally the cooperation and response to pollution incidents. (UK)

  13. Oil shale highlights

    International Nuclear Information System (INIS)

    1994-01-01

    The low prices of crude oil have continued to retard the commercial development of oil shale and other syn fuels. Although research funds are more difficult to find, some R and D work by industry, academia, and governmental agencies continues in the United States and in other parts of the world. Improvements in retorting technology, upgrading oil-shale feedstock, and developing high-value niche-market products from shale oil are three notable areas of research that have been prominent for the past several years. Although the future prices of conventional crude cannot be predicted, it seems evident that diminishing supplies and a burgeoning world population will force us to turn to alternate fossil fuels as well as to cleaner sources of non-fossil energy. (author)

  14. Uncertainty in oil projects

    International Nuclear Information System (INIS)

    Limperopoulos, G.J.

    1995-01-01

    This report presents an oil project valuation under uncertainty by means of two well-known financial techniques: The Capital Asset Pricing Model (CAPM) and The Black-Scholes Option Pricing Formula. CAPM gives a linear positive relationship between expected rate of return and risk but does not take into consideration the aspect of flexibility which is crucial for an irreversible investment as an oil price is. Introduction of investment decision flexibility by using real options can increase the oil project value substantially. Some simple tests for the importance of uncertainty in stock market for oil investments are performed. Uncertainty in stock returns is correlated with aggregate product market