WorldWideScience

Sample records for steel-din-1-4981

  1. Study of the influence of mechanical - thermal treatments on the creep behavior of a niobium stainless steel

    International Nuclear Information System (INIS)

    Rossi, J.L.; Ferreira, P.I.

    1986-01-01

    The influence of microstructural parameters controlled by mechanical-thermal treatment |1| on the creep behavior of DIN-Werkstoff-Nr. 1.4981 stainless steel (material candidate for use as cladding of fast breeder reactor (fuel elements), is studied. The effects of the solution treatment, predeformation, predeformation puls aging and cycles of predeformation-ageing on the creep results obtained at 990 K, for apllied stresses in the range 70 MPc - 310 MPa, are discussed. (Author) [pt

  2. Fatigue of DIN 1.4914 martensitic stainless steel in a hydrogen environment

    Science.gov (United States)

    Shakib, J. I.; Ullmaier, H.; Little, E. A.; Faulkner, R. G.; Schmilz, W.; Chung, T. E.

    1994-09-01

    Fatigue tests at room temperature in vacuum, air and hydrogen have been carried out on specimens of DIN 1.4914 martensitic stainless steel in load-controlled, push-pull type experiments. Fatigue lifetimes in hydrogen are significantly lower than in both vacuum and air and the degradation is enhanced by lowering the test frequency or introducing hold times into the tension half-cycle. Fractographic examinations reveal hydrogen embrittlement effects in the form of internal cracking between fatigue striations together with surface modifications, particularly at low stress amplitudes. It is suggested that gaseous hydrogen can influence both fatigue crack initiation and propagation events in martensitic steels.

  3. Study of tempering process of a DIN 1.2714 steel modified by niobium

    International Nuclear Information System (INIS)

    Oliveira, Carlos A.S. de.

    1985-01-01

    The carbides precipitaton in a DIN 1.2714 steel modified by niobium are studied. Three austenitizing temperatures (1200, 960 and 860 0 C) after homogenization at 1200 0 C are used; and the precipitation behavior of the carbides on tempering at 600 0 C with respect to time is studied. These precipitates were characterized through the X-ray fluorescence and diffraction and by carbon extraction replica techniques for transmission electron microscope. (M.J.C.) [pt

  4. The creep and stress-rupture behaviour under internal pressure of tubes made from austenitic stainless steel X8 CrNiMoNb 1616 (Material No. 1.4981)

    International Nuclear Information System (INIS)

    Schaefer, L.; Polifka, F.; Kempe, H.

    1979-05-01

    Creep and stress rupture tests have been performed at 600, 650, 700 and 750 0 C on tubes made from three different heats from the austenitic stainless steel X8 CrNiMoNb 1616 (Material No. 1.4981). The tubes were loaded by internal pressure and the tangential (hoop) creep strain was measured continuously. The results are presented in form of creep curves, stress-time to rupture curves and curves for a creep limit. The average and minimum creep rates as a function of the applied stress have been evaluated and are described with a creep law analogous to Norton's creep law. An interpolation and extrapolation of the stress-rupture-strength and the creep strength are possible using the time-temperature-parameter-plot after Larson and Miller. (orig.) [de

  5. 26 CFR 55.4981-1 - Imposition of excise tax on certain real estate investment trust taxable income not distributed...

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 17 2010-04-01 2010-04-01 false Imposition of excise tax on certain real estate investment trust taxable income not distributed during the taxable year; taxable years ending on or before January 1, 1987. 55.4981-1 Section 55.4981-1 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE...

  6. Effect of helium on creep and fatigue (MAT 11)

    International Nuclear Information System (INIS)

    Schroeder, H.

    1991-03-01

    This final report contains experimental results on mechanical properties (creep, fatigue, tensile) and microstructural investigations (SEM, TEM) of pre-implanted samples of steels or alloys. (AISI 316, AISI 316L, DIN 1.4970, JPCA 8206, DIN 1.4914; Incoloy 800H, Hastelloy X, DIN 1.4981, (Fe 0.49 Ni 0.51 ) 3 V, Fe17Ni17Cr, Fe15Ni15Cr, Nimonic PE 16, Ni8Si). Furthermore theoretical aspects and developed models and mechanisms for helium embrittlement are described. This report is presented in the form of an extended summary without figures. (MM)

  7. Effects of neutron irradiation and fatigue on ductility of stainless steel DIN 1.4948

    International Nuclear Information System (INIS)

    Vries, M.I. de; Schaaf, B. van der; Staal, H.U.; Elen, J.D.

    1978-10-01

    Test specimens of stainless steel DIN 1.4948, which is similar to AISI type 304, have been irradiated at 723 K and 823 K up to fluences of 1.10 23 neutrons (n).m -2 and 5.10 24 n.m -2 (E > 0.1 MeV). These are representative conditions for the SNR-300 reactor vessel and inner components after 16 years of operation. High temperature (723 K to 1023 K) tensile tests at strain rates (depsilon/dt) from 10 -7 s -1 to 10 s -1 show a considerable decrease of tensile ductility. The extent depends on helium content, test temperature and strain rate. The atomic helium fractions of 3.10 -7 and 7.10 -6 result from the reactions of thermal neutrons with the 14 ppm boron, present in the steel. Helium embrittlement sets in at strain rates below 1 s -1 to 10 s -1 (the range of interest for Bethe-Tait accident analyses). A minimum total elongation value of 6% is shown at 923 K. The post-irradiation fatigue life is reduced by up to about 50% due to intergranular cracking. The combination of irradiation and fatigue causes a decrease of ductility after a smaller number of prior fatigue cycles than in the case of unirradiated material. (Auth.)

  8. Effects of mechanical-thermal treatments on the creep behaviour of a niobium stabilized stainless steel

    International Nuclear Information System (INIS)

    Rossi, J.L.

    1987-01-01

    The influence of microstructural variables controlled by mechanical-thermal treatments on the creep behavior of DIN-Werkstoff Nr. 1,4981 stainless steel a material candidate for use as cladding of fast breeder reactor fuel elements, was studied. The effect of the solution treatment, predeformation, predeformation plus aging and cycles of predeformation-aging, on the creep results obtained at 990 K, for applied stresses in the range 70 MPa - 310 MPa, are analysed. The results show: this material presents a creep strength superior to that show by AISI 316 stainless steel; a transition on the creep behavior is observed at a certain stress; the mechanical-thermal treatments were seen to be ineffective on the improvement of the creep strength; the pre-deformation and pre-deformation plus aging treatments were seen to induce material embrittlement whereas the cyclic treatments induced increased ductility. Transmission electron microscopy, X ray diffraction of extracted precipitates, and microanalysis were use to characterize the microstructure of this material. (author)

  9. Microstructure and thermomechanical pretreatment effects on creep behaviour of helium-implanted DIN 1.4970 austenitic stainless steel

    International Nuclear Information System (INIS)

    Matta, M.K.; Kesternich, W.

    1990-01-01

    Microstructure investigations were carried out on unimplanted and 150 at ppm helium implanted foil specimens of DIN 1.4970 austenitic stainless steel after various thermomechanical pretreatments. Creep test were also carried out for both helium-implanted and unimplanted specimens at 700degC and 800degC. The strength, ductility and rupture time are correalted with the dislocation and precipitate distributions. Helium embrittlement can be reduced in these experiments when dispersive TiC precipitate distributions are produced by proper pretreatments or allowed to form during creep test. (author). 14 refs., 11 figs

  10. Effects of neutron irradiation and fatigue on ductility of stainless steel DIN-1-4948

    International Nuclear Information System (INIS)

    de Vries, M.I.; van der Schaaf, B.; Staal, H.U.; Elen, J.D.

    1978-01-01

    Test specimens of stainless steel DIN 1.4948, which is similar to AISI Type 304, have been irradiated at 723 and 823 K up to fluences of 1*10$sup 23$ neutrons (n)*m$sup -2$ and 5*10$sup 24$ n*m$sup -2$ (E>0.1 MeV). These are representative conditions for the reactor vessel and inner components of the liquid metal fast breeder reactor SNR-300 after 16 years of operation. High-temperature (723 to 1023 K) tension tests at strain rates ($epsilon$) from 10$sup -7$ to 10 s$sup -1$ show a considerable decrease of tensile ductility. The extent depends on helium content, test temperature, and strain rate. The atomic helium fractions of 3*10$sup -7$ and 7*10$sup -6$ result from the reactions of thermal neutrons with the 14 ppm boron present in the steel. Helium embrittlement sets in at strain rates below 1 to 10 s$sup -1$ (the range of interest for Bethe-Tait accident analyses). A minimum total elongation value of 6 percent is shown at 923 K. The postirradiation fatigue life is reduced by up to about 50 percent due to intergranular cracking. The combination of irradiation and fatigue causes a decrease of ductility after a smaller number of prior fatigue cycles than in the case of unirradiated material. 8 refs

  11. Evaluation of the effect of the partial substituttion of vanadium and molybdenum by niobium in a tool steel DIN W. NR. 1.2714

    International Nuclear Information System (INIS)

    Isore, A.; Pereira, O.J.; Aleixo, C.

    1982-01-01

    A comparative study of the properties of a steel DIN W. Nr 1.2714 and those of two steels of the same type but with lower amounts of molybdenum and vanadium, higher amounts of silicon and chromium, and with the adition of niobium (0,08 and 0,17%), was carried out. In the three steels with niobium there are niobium carbides wich are aligned in the hot deformation direction, and do not dissolve at the normal austenitizing temperatures. In the steel with higher niobium content, these carbides affect the transverse toughness and its hot ductility (200 - 600 0 C), although sensibly improving the abrasion wear resistance. The results of the fracture toughness and Charpy test, suggest that the niobium carbides do not decrease the crack nucleation resistance. (Author) [pt

  12. Comparison of the corrosion resistance of DIN W. Nr. 1.4970 (15%Cr-15%Ni-1.2%Mo-Ti and ASTM F-138 (17%Cr-13%Ni-2.5%Mo austenitic stainless steels for biomedical applications

    Directory of Open Access Journals (Sweden)

    Maysa Terada

    2006-09-01

    Full Text Available The resistance to localised corrosion of the full austenitic 15%Cr-15%Ni-1.2%Mo titanium stabilized stainless steel (DIN W. Nr. 1.4970 was investigated by electrochemical methods including electrochemical impedance spectroscopy (EIS, potentiodynamic polarization and potentiostatic polarization measurements in a phosphate-buffered solution (PBS. The low carbon and non-stabilized austenitic stainless steel, AISI 316L (ASTM F-138, widely used for surgical implants, was also tested for comparison. The tests were conducted at room temperature after a stable potential had been reached. After the electrochemical measurements, the surfaces of the specimens were observed using SEM to evaluate the presence of pits. Potentiodynamic polarization results showed that both steels are prone to localized corrosion. Larger pits were found on the surface of AISI 316L specimens after the electrochemical tests. EIS response has indicated the duplex structure of the passive oxides. The results showed that the electrochemical behaviour of the DIN W. Nr. 1.4970 is better than of AISI 316L steel. Therefore, their application as an implant material may be considered.

  13. 'In-beam' simulation of high temperature helium embrittlement of DIN 1.4970 austenitic stainless steel

    International Nuclear Information System (INIS)

    Schroeder, H.; Batfalsky, P.

    1982-01-01

    This work describes a facility for high temperature creep rupture tests during homogeneous helium implantation. This 'in-beam' creep testing facility is used to simulate helium embrittlement effects which will be very important for first wall materials of future fusion reactors operated at high temperatures. First results for DIN 1.4970 austenitic stainless steel clearly demonstrate differences between samples 'in-beam' tested at 1073 K and those creep tested at the same temperature after room temperature helium implantation. The specimens ruptured 'in-beam' have much shorter lifetimes and lower ductility than the specimens tested after room temperature implantation. There are also differences in the microstructures, concerning helium bubble sizes and densities in matrix and grain boundaries. These microstructural differences may be a key for the understanding of the more severe helium embrittlement effects 'in-beam' as compared to creep tests performed after room temperature implantation. (orig.)

  14. Creep-rupture-strength and creep-behaviour of stainless steel X6CrNi 1811 (DIN 1.4948)

    International Nuclear Information System (INIS)

    Solano, R.R.; Rivas, M. de las; Seith, B.; Schirra, M.

    1977-01-01

    The steel X6CrNi 1811 (DIN 1.4948) that will be used as a structure material for the german fast breder reactor SNR 300, was creep-tested in a temperature range of 550-650 deg C under base material condition as well as welded material condition. Tests are foreseen up to 30.000 hours with a continous measuring of the elongation. The test results up to about 4.000 hours is described. Taking into account the results of other programs carried out with the same material between 550 and 600 deg C at similar rupture time, were defined the stresses for the longterm test. The main point of this program (''Extrapolation Program'') lies in the knowledge of the creep-rupture-strength and creep behaviour of the structure materials up to 3.10 4 h at high temperature in order to extrapolate up to 10 5 h for reactor operating temperatures. (author) [es

  15. Creep-rupture-strength and creep-behaviour of stainless steel X6CrNi 1811(DIN 1.4948)

    International Nuclear Information System (INIS)

    Solano, R. R.; Schirra, M.; Rivas, M. de la; Seith, B.

    1977-01-01

    The steel X6CrNi 1811 (DIN 1.4948) that will be used as a structure material for the German Fast Breeder Reactor SNR 300 was creep-tested in a temperature range of 550-650 degree centigree under base material condition as well as welded material condition. Tests are foreseen up to 30.000 hours with a continuous measuring of the elongation. The present report describes the test results up to about 4-000 hours. Taking into account the results of other programs carried out with the same material between 550- and 600 degree centigree at similar rupture time, were defined the stresses for the long term tests. The main point of this program (Extrapolation Program) lies in the knowledge of the creep-rupture-strength and creep behaviour of the structure materials up to 3.10 4 h at high temperature in order to extrapolate up to 10 5 h. for reactor operating temperatures. (Author) 14 refs

  16. Creep-rupture-strength and creep-behaviour of stainless steel X6CrNi 1811 (DIN 1.4948)

    International Nuclear Information System (INIS)

    Solano, R.R.; Rivas, M. de las; Schirra, M.; Seith, B.

    1976-10-01

    The steel X6CrNi 1811 (DIN 1.4948) that will be used as a structure material for the German fast breeder reactor SNR 300 was creep-tested in a temperature range of 550-650 0 C under base material condition as well as welded material condition. Tests are foreseen up to 30.000 hours with a continuous measuring of the elongation. The present report describes the test results up to about 5.000 hours. Taking into account the results of other programs carried out with the same material between 550 and 600 0 C at similar rupture times, were defined the stresses for the long term tests. The main point of this program ('Extrapolation Program') lies in the knowledge of the creep time and creep behaviour of the structure materials up to 3 x 10 4 h at high temperature in order to extrapolate up to 10 5 h for operating temperatures. (orig.) [de

  17. Submerged arc narrow gap welding of the steel DIN 20MnMoNi55

    International Nuclear Information System (INIS)

    Moraes, M.M.

    1987-01-01

    The methodology for submerged arc narrow gap welding for high thickness rolled steel DIN 20MnMoNi55 was developed, using din S3NiMo1 04 mm and 05 mm wires, and DIN 8B435 flux. For this purpose, submerged arc narrow gap welded joints with 50 mm and 120 mm thickness were made aiming the welding parameters optimization and the study of the influence of welding voltage, wire diameter and wire to groove face distance on the operational performance and on the welded joint quality, specially on the ISO-V impact toughness. These welded joints were checked by non-destructive mechanical and metallographic tests. Results were compared with those obtained by one 120 mm thickness submerged arc conventional gap welded joint, using the same base metal and consumables (05 mm wire). The analysis of the results shows that the increasing of the wire to groove face distance and the welding voltage increases the hardness and the ISO-V impact toughness of the weld metal. It shows that the reduction of the gap angle is the main cause for the obtained of a heat affected zone free from coarse grains, the reduction of the welding voltage, the increasing of the wire to groove face distance, and the grounding optimization also contribute for that. It was also concluded that the quality and the execution complexity level of a narrow gap welded joint are identical to a conventional gap welded joint. (author) [pt

  18. The influence of thermomechanical treatment on the creep behaviour of DIN 1.4970 austenitic stainless steel at 973 K

    International Nuclear Information System (INIS)

    Zahra, A.A.A.; Schroeder, H.

    1981-04-01

    The creep-rupture behaviour of a Type DIN 1.4970 austenitic stainless steel has been investigated at 973 K (700 0 C) in a high vacuum for three conditions of thermomechanical treatment and a wide range of applied stresses. This type of steel is a candidate for use in the German SNR-300 Fast Breeder Reactor where it shall be used after a 13% cold-working treatment and subsequent aging at 1073 K (800 0 C) for 24 hours ( standard condition ). As an alternative, two other conditions were also investigated, namely aged at 1073 K (800 0 C) for 24 hours before the cold-working (condition 2) and cold worked only (condition 1). Because of various experimental efforts in this laboratory and elsewhere to study helium induced embrittlement effects in α-implanted foil specimens, all tests were performed using foil specimens of 105 μm thickness which were solution annealed at 1373 K (1100 0 C) before the above thermomechanical treatments were applied. The rupture lives and the minimum creep rates were found to be highly dependent on the applied stresses. The treatment of condition 1 material yielded a product as strong as the standard condition 3, while the condition 2 material was less creep resistant. Structural changes as well as fractography were followed using metallographic, transmission and scanning electron microscope techniques. Transgranular ductile fracture was clearly observed in all three conditions. TEM investigations showed that dispersive TiC precipitates were present in the matrix of condition 3 material before creep testing contrary to condition 1 and 2 material. In condition 1 the TiC dispersion was already found after short creep times, while no dispersive TiC precipitates were found in condition 2 material in every test condition. (orig.) [de

  19. Electrochemical studies of the corrosion behavior of the fine-grained structural steel DIN W.Nr. 1.0566 between 55 and 90deg C in simulated salt brine repository environments

    International Nuclear Information System (INIS)

    Farvaque-Bera, A.M.; Leistikow, S.

    1991-05-01

    The electrochemical corrosion of the fine-grained structural steel DIN W. Nr. 1.0566 was tested between 55 and 90deg C in three simulated salt brines of similar compositions as analyzed for the Gorleben repository environment. As test parameters the temperature, the salt brine composition, the stirring velocity and the oxygen content as well as the state of the steel surface were varied. As experimental results are presented: (1) the free corrosion potentials of the steel in three brines, (2) Tafel plots of current densities as measured potentiodynamically in the anodic and cathodic vicinity of the corrosion potentials and being representative for the rate of metal dissolution, (3) the surface morphology of the corroded specimens. As mechanisms - in the absence of oxygen - the cathodic reduction of water and the anodic dissolution of iron are considered to prevail the corrosion reaction. It is shown that the applied electrochemical techniques are able to determine within an accelerated procedure the most important corrosion parameters in respect to their influence on rate of metal dissolution and morphology of corrosion attack. (orig.) [de

  20. Ultrasonic testing and inspection of steel castings for use in elevated temperatures acc. to DIN 17245

    International Nuclear Information System (INIS)

    Christianus, D.; Fischer, K.H.

    1978-01-01

    Up to present, the non-destructive testing in german steel castings and delivery conditions has hardly been described. DIN 17245 was an exception for heat-resistant ferrite cast steel (July 1967 version) which for the first time contained data on maximum permissible defects in irradiation testing. The US (ultrasonic) method to find internal defects was named together with irradiation, the error limits however were also valid for this method according to the reference picture series of ASTM (American Society for Testing and Materials). It is clear to every practician that especially in the case of steel, due to the numerous possible defects and their unpredictable orientation, it is not always possible to determine the true type of defects based on reflection behaviour of an inhomogenity. In any case one cannot directly compare two physically different methods. If one considers foreign cast steel norms, then one finds somewhat more about non-destructive testing. The set standard measures mostly however take after the irradiation testing guidelines according to ASTM. A Westinghouse regulation, norm ASTM-A-609 and the ASME (Am. Soc. of Mech. Engineers) regulations for components of nuclear reactors are the exception. (orig.) [de

  1. The irradiation behaviour of the austenitic stainless steel DIN 1.4970

    International Nuclear Information System (INIS)

    Huebner, R.

    2000-06-01

    The irradiation behaviour of the austenitic stainless steel DIN 1.4970 (15% Cr, 15% Ni, 1,6% Mn, 1,5% Mo, 0,4 - 1% Si, 0,3 - 0,5% Ti) has been examined in the irradiation experiment PFR-M2. The samples have been irradiated as pressurised capsules in the prototype fast reactor at Dounreay, Scotland, at 420, 500 and 600 C with maximum doses of 106, 81 and 62 dpa NRT . The stress-free and the stress-induced swelling and the irradiation induced creep could be determined by the diameter and length measurements. After the irradiation the density and the mechanical properties have been determined. Additionally the microstructure was investigated with a transmission electron microscope (TEM). All four lots show the maximum amount of stress-free swelling at 420 C. At 600 C no swelling can be detected up to the maximum dose of 62 dpa NRT . The lot with the lowest Si-content exhibits the highest amount of swelling at 420 C as well as at 500 C. Increasing the Si-content from 0.4% to 1% increases at 420 C the incubation dose from 20 to 40 dpa NRT , but has no influence on the swelling rate. Increasing not only the Si-content but also reducing the Ti-content from 0.5 to 0.3% increases not only the incubation dose but also reduces the swelling rate. At 500 C both the increase of the Si-content and the reduction of the Ti-content result in a reduced swelling rate without any effect on the incubation dose. Therefore the best swelling resistance is achieved with a high Si-content and a low Ti-content, resulting in an understabilised condition. The TEM analysis of the microstructure reveals the mechanisms by which the minor elements influence swelling. Increasing the Si-content increases the vacancy mobility and reduces therefore the void nucleation rate. This yields the increased incubation dose. But this mechanism is only working if the silicon is dissolved in the matrix. Swelling starts when the amount of dissolved silicon is reduced under a certain amount. The lots with a high Si

  2. Creep-rupture-tests on thestainless steel X6 CrNi1811 (DIN 1.4948) in the frame of the ''Extrapolation-Program'' Pt. 2

    International Nuclear Information System (INIS)

    Solano, R.R.; Barroso, S.; Rivas, M. de las; Schirra, M.; Seith, B.

    1979-01-01

    The austenitic stainless steel X6 CrNi 1811 (DIN 1.4948) that is used as a structure material for the German Fast Breeder Reactor SNR 300 was creep tested in a temperature range of 550-650 deg under base material condition as well as welded material condition. The main point of this program (''Extrapolation-Program'') lies in the knowledge of the cree-rupture-strength and creep-behaviour up to 3X10 - 4 hours at higher temperatures in order to extrapolate up to (>=)10 5 hours for operating temperatures. In order to study the stress dependency of the minimum creep rate additional tests were carried out over temperature range 550 deg - 750 deg C. The present report describes the state in the running program with test-time up to 35.000 hours. Besides the cree-rupture behaviour it is possible to make a distinct quantitative statement for the creep-behaviour and ductility. Extensive metallographic examinations show the fracture behaviour and changes in structure. (author)

  3. Tensile properties of irradiated and fatigue exposed stainless steel DIN X 6 CrNi 1811 (similar to AISI type 304) plate and welded joints

    International Nuclear Information System (INIS)

    Vries, M.I. de; Schaaf, B. van der; Elen, J.D.

    1979-10-01

    Test specimens of plate metal and welded joints of stainless steel DIN 1.4948, which is similar to AISI type 304, have been irradiated at 723 K and 823 K up to fluences of 1.10 23 n.m -2 and 5.10 24 n.m -2 (E > 0.1 MeV). These are representative conditions for the SNR-300 reactor vessel and inner components after 16 years of operation. High-rate (depsilon/dt = 1 s -1 ) tensile tests were performed after fatigue exposure up to various fractions of fatigue life (D) ranging from 5% to 95% at the same temperatures as the nominal temperatures of the irradiation series

  4. Creep-rupture-test on the stainless steel X6CRNI1811 (DIN 1.4948) in the frame of the ''Extrapolation-Program''. (Part III)

    International Nuclear Information System (INIS)

    Solano, R.; Las Rivas, M. de; Barroso, S.

    1982-01-01

    The austenitic stainless steel X6CrNi1811 (DIN 1.4948) used as a structure material for the German Fast Breeder Reactor SNR 300 was creep tested in a temperature range of 550-650 deg under base material condition as well as welded material condition. The main point of this program (''Extrapolation-Program'') lies in the knowledge of the creep-rupture-strength and creepbehaviour up to 3 x 10 4 hours at higher temperatures in order to extrapolate up to >=10 5 hours for operating temperatures. In order to study the stress dependency of the minimum creep rate additional tests were carried out of 550 deg - 750 deg C. The present report describes the state in the running program with test-times of 23.000 hours and results from tests up to 55.000 hours belonging to other parallel programs are taken into account. Besides the creep-rupture behaviour it is also made a study of ductility between 550 and 750 deg C. Extensive metallographic examinations have been made to study the fracture behaviour and changes in structure. (author)

  5. Creep-rupture-test on the stainless steel X6crni1811 (Din 1.494.8) in the frame of the Extrapolation-Program. (Part III)

    International Nuclear Information System (INIS)

    Solano, R.; Schirra, M.; Rivas, M. de la; Barroso, S.; Seith, B.

    1982-01-01

    The austenitic stainless steel X6crni1811 (Din 1.4948) used as a structure material for the German Fast Breeder Reactor SNR 300 was creep tested in a temperature range of 550-650 degree centigree material condition as well as welded material condition. The main point of this program (Extrapolation-Program) lies in the knowledge of the creep-rupture-strength and creep-behaviour up to 3 x 10 4 hours higher temperatures in order to extrapolated up to ≥10 5 hours for operating temperatures. In order to study the stress dependency of the minimum creep rate additional tests were carried out of 550 degree centigree - 750 degree centigree. The present report describes the state in the running program with test-times of 23.000 hours and results from tests up to 55.000 hours belonging to other parallel programs are taken into account. Besides the creep-rupture behaviour it is also made a study of ductility between 550 and 750 degree centigree. Extensive metallographic examinations have been made to study the fracture behaviour and changes in structure. (Author)

  6. Austenitic stainless steel alloys with high nickel contents in high temperature liquid metal systems

    International Nuclear Information System (INIS)

    Konvicka, H.R.; Schwarz, N.F.

    1981-01-01

    Fe-Cr-Ni base alloys (nickel content: from 15 to 70 wt%, Chromium content: 15 wt%, iron: balance) together with stainless steel (W.Nr. 1.4981) have been exposed to flowing liquid sodium at 730 0 C in four intervals up to a cumulative exposure time of 1500 hours. Weight change data and the results of post-exposition microcharacterization of specimens are reported. The corrosion rates increase with increasing nickel content and tend to become constant after longer exposure times for each alloy. The corrosion rate of stainless steel is considerably reduced due to the presence of the base alloys. Different kinetics of nickel poor (up to 35% nickel) and nickel rich (> 50% nickel) alloys and nickel transport from nickel rich to nickel poor material is observed. (orig.)

  7. Creep-rupture-strength and creep-behaviour of stainless steel X6CrNi 1811(DIN 1.4948); Comportamiento a la fluencia lenta del acero X6CrNi 1811 (1.4948)

    Energy Technology Data Exchange (ETDEWEB)

    Solano, R R; Schirra, M; Rivas, M de la; Seith, B

    1977-07-01

    The steel X6CrNi 1811 (DIN 1.4948) that will be used as a structure material for the German Fast Breeder Reactor SNR 300 was creep-tested in a temperature range of 550-650 degree centigree under base material condition as well as welded material condition. Tests are foreseen up to 30.000 hours with a continuous measuring of the elongation. The present report describes the test results up to about 4-000 hours. Taking into account the results of other programs carried out with the same material between 550- and 600 degree centigree at similar rupture time, were defined the stresses for the long term tests. The main point of this program (Extrapolation Program) lies in the knowledge of the creep-rupture-strength and creep behaviour of the structure materials up to 3.10{sup 4}h at high temperature in order to extrapolate up to 10{sup 5} h. for reactor operating temperatures. (Author) 14 refs.

  8. Decreased Fitness and Virulence in ST10 Escherichia coli Harboring blaNDM-5 and mcr-1 against a ST4981 Strain with blaNDM-5

    Directory of Open Access Journals (Sweden)

    Yawei Zhang

    2017-06-01

    Full Text Available Although coexistence of blaNDM-5 and mcr-1 in Escherichia coli has been reported, little is known about the fitness and virulence of such strains. Three carbapenem-resistant Escherichia coli (GZ1, GZ2, and GZ3 successively isolated from one patient in 2015 were investigated for microbiological fitness and virulence. GZ1 and GZ2 were also resistant to colistin. To verify the association between plasmids and fitness, growth kinetics of the transconjugants were performed. We also analyzed genomic sequences of GZ2 and GZ3 using PacBio sequencing. GZ1 and GZ2 (ST10 co-harbored blaNDM-5 and mcr-1, while GZ3 (ST4981 carried only blaNDM-5. GZ3 demonstrated significantly more rapid growth (P < 0.001 and overgrew GZ2 with a competitive index of 1.0157 (4 h and 2.5207 (24 h. Increased resistance to serum killing and mice mortality was also identified in GZ3. While GZ2 had four plasmids (IncI2, IncX3, IncHI2, IncFII, GZ3 possessed one plasmid (IncFII. The genetic contexts of blaNDM-5 in GZ2 and GZ3 were identical but inserted into different backbones, IncX3 (102,512 bp and IncFII (91,451 bp, respectively. The growth was not statistically different between the transconjugants with mcr-1 or blaNDM-5 plasmid and recipient (P = 0.6238. Whole genome sequence analysis revealed that 28 virulence genes were specific to GZ3, potentially contributing to increased virulence of GZ3. Decreased fitness and virulence in a mcr-1 and blaNDM-5 co-harboring ST10 E. coli was found alongside a ST4981 strain with only blaNDM-5. Acquisition of mcr-1 or blaNDM-5 plasmid did not lead to considerable fitness costs, indicating the potential for dissemination of mcr-1 and blaNDM-5 in Enterobacteriaceae.

  9. Monotonic and Cyclic Behavior of DIN 34CrNiMo6 Tempered Alloy Steel

    Directory of Open Access Journals (Sweden)

    Ricardo Branco

    2016-04-01

    Full Text Available This paper aims at studying the monotonic and cyclic plastic deformation behavior of DIN 34CrNiMo6 high strength steel. Monotonic and low-cycle fatigue tests are conducted in ambient air, at room temperature, using standard 8-mm diameter specimens. The former tests are carried out under position control with constant displacement rate. The latter are performed under fully-reversed strain-controlled conditions, using the single-step test method, with strain amplitudes lying between ±0.4% and ±2.0%. After the tests, the fracture surfaces are examined by scanning electron microscopy in order to characterize the surface morphologies and identify the main failure mechanisms. Regardless of the strain amplitude, a softening behavior was observed throughout the entire life. Total strain energy density, defined as the sum of both tensile elastic and plastic strain energies, was revealed to be an adequate fatigue damage parameter for short and long lives.

  10. Irradiation creep of the martensitic steel no. 1.4914 between 400 deg C and 600 deg C (Mol 5B)

    International Nuclear Information System (INIS)

    Herschbach, K.; Doser, W.

    1983-01-01

    The irradiation induced creep of the martensitic steel DIN No. 1.4914 was investigated in the temperature range from 400 to 600 deg C for stresses up to 200 Mpa using the Mol 5B irradiation rig. The results point to a behavior quite different from that observed in the austenitic steels as will be discussed in detail. The creep is thermally activated and non-linearly dependent upon the applied stress. (author)

  11. 26 CFR 55.4981-2 - Imposition of excise tax with respect to certain undistributed income of real estate investment...

    Science.gov (United States)

    2010-04-01

    ... certain undistributed income of real estate investment trusts; calendar years beginning after December 31... (CONTINUED) MISCELLANEOUS EXCISE TAXES (CONTINUED) EXCISE TAX ON REAL ESTATE INVESTMENT TRUSTS AND REGULATED INVESTMENT COMPANIES Excise Tax on Real Estate Investment Trusts § 55.4981-2 Imposition of excise tax with...

  12. Microstructure and intergranular corrosion of the austenitic stainless steel 1.4970

    International Nuclear Information System (INIS)

    Terada, Maysa; Saiki, Mitiko; Costa, Isolda; Padilha, Angelo Fernando

    2006-01-01

    The precipitation behaviour of the DIN 1.4970 steel and its effect on the intergranular corrosion resistance were studied. Time-temperature-precipitation diagrams for the secondary phases (Ti, Mo)C (Cr, Fe, Mo, Ni) 23 C 6 and (Cr, Fe) 2 B are presented and representative samples have been selected for corrosion studies. The susceptibility to intergranular corrosion of the samples was evaluated using the double loop electrochemical potentiokinetic reactivation technique. The results showed that the solution-annealed samples and those aged at 1173 K did not present susceptibility to intergranular corrosion, whereas aging treatment from 873 to 1073 K resulted in small susceptibility to intergranular attack that decreased with aging temperature. The preferential formation of (Ti, Mo)C at higher aging temperatures comparatively to M 23 C 6 , retained the chromium in solid solution preventing steel sensitization and, consequently, intergranular corrosion

  13. Post-irradiation creep properties of four plates and two forgings DIN 1.4948 steel from the SNR-300 permanent primary structures

    International Nuclear Information System (INIS)

    Schaaf, B. van der.

    1987-01-01

    The safety authorities, involved in the licensing procedure of the SNR-300, have required the determination of the irradiation effect on the heat-to-heat variation of tensile and creep properties of Werkst. No. DIN 1.4948 austenitic stainless steel. These data are lacking in the present codes and they are necessary for the design and safety considerations of the permanent structures. Results are presented of about 200 tests on irradiated and unirradiated material of 6 heats used in the production of the SNR-300 permanent structures. After irradiation in the HFR-Petten to neutron fluences relevant for the SNR-300 service conditions post-irradiation tensile and creep tests (up to 10,000 hrs rupture time) were performed in the temperature range 723 K to 923 K. All heats are embrittled by irradiation resulting in reduction of rupture times, creep strength and ultimate tensile strength. The considerable reduction is attributed to helium enhanced intergranular creep crack growth, which reduces the ductility and strength, but does not affect the creep rate. The variation of tensile and creep properties is large and independent of irradiation. The minimum derived creep strength in irradiated condition drops below the values expected in the ASME Code and VdTuV Blatt. In design and safety analyses the irradiation effect on creep properties must be accounted for with an appropriate reduction factor. The predictions given, have to be verified with long-term creep tests and parts of the SNR surveillance programme. 172 figs.; 17 refs.; 58 tables

  14. Welding of Low Alloy Steel DIN 15Mo3 by MIG/MAG Spot

    OpenAIRE

    Nabeel K. Abid Al- Sahib

    2006-01-01

    ????? ????? ????? ????? ??????? ?????? ?? ????? ?????? ?????? ?????? ??????? ?????? ?????? (MIG/MAG spot) ???????? ??? ??????? ????? ?? ???? ???????? ????? ??? ???????? ?? ?????? ??????????? ??????? ???????? ????? ???? ??????? ??????? ????? ??? (DIN15Mo3) ?????? ?????? ?????? ?????? ?????? ?? ???? ???? ?????? ???????" ??? ?????? ??? ????. ????? ??????? ??????? ?????? ??? CO2 ????" ?? ??? ??????? ?? ???? ??????? ??????? ????? ?? ?????? ????? ?? ??? ???? ?? ????? (13%) ???? (4mm) ???? (2sec). ?...

  15. Cathode-sputtered Ti-Zr-N-C-O base hard coatings and stability of said coatings on hard metals and working steels. Kathodenzerstaeubte Hartstoffschichten auf Basis Ti-Zr-N-C-O und deren Stabilitaet auf Hartmetall und Gebrauchsstaehlen

    Energy Technology Data Exchange (ETDEWEB)

    Boehmer, M.

    1986-02-26

    This paper deals with the examination of the metallurgical and thermal stability of the resistant material layers of titanium in connection with the substrate material influence. As substrate material were chosen: hard metal (81% WC, 12% TiC+TaC, 7% Co), high speed steel (DIN 1.3343), austenitic nickel chromium steel (X5 CrNi 18 9) and unalloyed tool steel (DIN 1.1545). The hard materials of titanium were deposited by means of cathode evaporation.

  16. New heating load calculation in practice. DIN 4701 vs. DIN EN 12831; Neue Heizlastberechnung in der Praxis. DIN 4701 vs. DIN EN 12831

    Energy Technology Data Exchange (ETDEWEB)

    Kroeber, C [Rehau-Akademie Bau, Erlangen (Germany)

    2004-09-15

    DIN EN 12831 is the most controversial technical standard that ever was. The contribution shows the changes from DIN 4701 and their consequences on heating systems and heating grids. (orig.) [German] Wie keine andere Norm, die in den letzten Jahren im Hinblick auf die europaeische Harmonisierung eingefuehrt wurde, sorgt die Heizlastberechnung nach DIN EN 12831 fuer reichlich Gespraechsstoff. In folgendem Beitrag wird beschrieben, welche Veraenderungen im Vergleich zur Waermebedarfsberechnung nach DIN 4701 auftreten und wie sie sich auf die Heizsysteme und Waermeerzeugungsanlagen auswirken. (orig.)

  17. On the dimensioning of steel construction considering revision of German standards

    International Nuclear Information System (INIS)

    Lindhorst, L.; Schaudinn, L.; Milleder, J.

    2005-01-01

    Different procedures for dimensioning of structural steelwork are investigated in this paper. In the non-nuclear area, there has been made a change in the design concept for structural steelwork of surface constructions in Germany and the deterministic design concept of German DIN 18800 (03/81) [1] has been replaced by the semi-probabilistic design concept of DIN 18800 (11/90) [2]. Design codes established in nuclear safety standards for steelwork in German nuclear facilities are considered in the paper. Recent revisions of German nuclear safety standards and specifications are discussed with respect to regulations concerning design codes. The change in design concept for structural steelwork (non-nuclear) has not been adopted in recent revisions of nuclear safety standards and specifications for steelwork of components with importance to safety. The deterministic concept of DIN 18800 (03/81) [1] is compared with the semi-probabilistic concept of DIN 18800 (11/90) [2]. Differences between the standards [1] and [2] are investigated using an example of a steel construction. Results for dimensioning according to DIN 18800 (03/81) [1] are compared to those for dimensioning according to DIN 18800 (11/90) [2] putting the main emphasis on stress analysis and building structure interaction loads. (authors)

  18. Explanations on nomenclature and number of material for steels in accordance with DIN norm - (Deutsch Industrie Norm)

    International Nuclear Information System (INIS)

    Barone, S.D.; Silva, T.C.V. da; Bittencourt, M.S.Q.

    1980-01-01

    The materials specified by DIN norm are identified by its nomenclature and corresponding DIN number. The characters (numbers and letters) aim to classify the material and provide indication on main alloy properties and elements. (M.C.K.) [pt

  19. X-ray protective clothing. Does DIN 6857-1 allow an objective comparison between lead-free and lead-composite materials?

    International Nuclear Information System (INIS)

    Eder, H.; Schlattl, H.; Hoeschen, C.

    2010-01-01

    Purpose: The validity of DIN 6857-1 to establish lead equivalence for protective clothing is evaluated by Monte Carlo simulations and measurements. Materials and Methods: Commercially available protective clothing made of lead, lead-free and lead-composite materials has been tested regarding its protective efficacy. The analysis has been performed on the one hand in accordance with the test conditions described in the manufacturing standard DIN EN 61331-3 and on the other hand following the new DIN 6857-1 standard. Additionally, measurements have been carried out under simulated patient conditions by using an Alderson-Rando phantom. Results: Following DIN EN 61331-3, the lead-free protective clothing achieved the required protective efficacy only at a restricted tube-voltage range. The test according to DIN 6857-1 showed that the protective criteria were fulfilled only by one lead-composite apron, but not by the three lead-free aprons examined. Thus, in order to guarantee the same protection as lead between 50 and 120 kV, the conditions of DIN 6857-1 must be fulfilled. Conclusion: A modification of DIN EN 61331-3 to account for secondary radiation is strongly advised in the case of lead-free materials. In summary, most of the protective lead-free aprons in use should be used with care, particularly for examinations with a high dose. (orig.)

  20. Mean Stress Effect on the Axial Fatigue Strength of DIN 34CrNiMo6 Quenched and Tempered Steel

    Directory of Open Access Journals (Sweden)

    Luis Pallarés-Santasmartas

    2018-03-01

    Full Text Available The present study consists of a theoretical and experimental investigation of the effect of axial mean stresses on the high cycle fatigue behaviour of DIN 34CrNiMo6 high strength steel in quenched and tempered conditions. The axial S-N curves under 4 different stresses ratios were obtained. Experimental results show that increasing the value of the tension mean stresses gradually reduces the axial stress amplitude the material can withstand without failure. Moreover, the compressive mean stresses show a beneficial effect in terms of the axial fatigue strength, resulting in a non-symmetrical Haigh diagram. A historic review of the axial mean stress effect is presented, showing the shape of the Haigh diagrams for ductile metals and presenting the most-known empirical and physical theories. The results for this steel are compared with the physical theories of Findley based on the critical plane; the Froustey’s and Marin’s methods, based on energetic theories; and the Crossland invariants method based on the Gough’s theory of fatigue damage. Taking into account the experimental results, a physical fatigue function based on energetic considerations is proposed. Its application to the fatigue case with mean stresses can be interpreted in terms of a balance of elastic energies of distortion and volume change. Macro-analyses of specimen fracture appearance were conducted in order to obtain the fracture characteristics for different mean stress values.

  1. Development of ferritic steels for steam generators of fast breeder reactors

    International Nuclear Information System (INIS)

    Nguyen-Thanh; Vigneron, G.; Vanderschaeghe, A.

    1988-01-01

    STEIN INDUSTRIE, a manufacturer of equipment for the conventional and nuclear power industry, has built up expertise in the use of Cr-Mo steels used at high temperatures. The main ferritic steels developed were 10 CD 9-10 (AFNOR), Z10 CDNb V 9-2 (AFNOR), X 20 Cr Mo V 12-1 (DIN) and ASTM Grade 9.1. For the fast breeder reactor system, STEIN INDUSTRIE proposes the use of these steels in the construction of steam generators. The wide programme of development undertaken by STEIN INDUSTRIE is aimed at the following main subjects: - characterization of materials - welding and bending tests - studies of special junctions. This article reports the results obtained

  2. Find din stemme

    DEFF Research Database (Denmark)

    Hansen, Jette Barnholdt

    2010-01-01

    Anmeldelse af Dorte Kock og Lene Kleinschmidts: Find din stemme. En brugsbog.Hans Reitzels Forlag 2010.......Anmeldelse af Dorte Kock og Lene Kleinschmidts: Find din stemme. En brugsbog.Hans Reitzels Forlag 2010....

  3. Photoelectrochemical studies on passive films of stainless steels

    International Nuclear Information System (INIS)

    Schmuki, P.; Boehni, H.

    1992-01-01

    Passive films on stainless steels, which are known to exhibit a significantly different susceptibility to pitting corrosion (DIN 1.4301, 1.4439, 1.4529), were in-situ examined by photoelectrochemistry. The results show that the photoresponse is determined by the defects in the electronic structure of the films leading to localized states in the band-gap region. It was found that the three different steels exhibit a different tailing of the density of states function into the band-gap region. The less deep localized states are present, the higher is the resistance of the material against pitting corrosion. It is therefore concluded that a correlation between the distribution of localized states in the passive film - i.e. its defect structure - and the stability of the film exists

  4. Microstructural investigations of fatigued 12% Cr-steel 1.4914 (X 18 Cr Mo V Nb 12 1)

    International Nuclear Information System (INIS)

    Gersinska, R.

    1992-10-01

    The low cycle fatigue properties of a tempered steel X18 Cr Mo V Nb 12 1 (DIN 1.4914) have been investigated at different temperatures, strain amplitudes, mean strains and strain rates. The role of martensite lath structure and of precipitates and dislocations on the strengthening mechanisms and fatigue damage have been analysed. Plastic deformation results in a slip band formation on the surface and in a cellular dislocation structure in the interior of the specimens. A reduced strain rate is causing lower stress amplitudes and greater cells at higher temperatures. At lower temperatures the influence of strain rate is small. Fatigue mechanisms are soon dominant at lower strain rates. REM-investigations of the specimen surfaces are revealing the development of cracks at slip bands. The cracks start always at the surfaces of the specimen, and they are transcristalline in nature. The influence of the ageing temperature has been investigated. A reduced ageing temperature of 600degC results in a higher dislocation density and a lower martensite lath distance in the undeformed material. Strain ageing was initially observed in tensile experiments. The influence of dynamic strain ageing on the mechanical properties and the microstructure of tempered steel 1.4914 is investigated. A correlation of mechanical and microstructural data has been performed. (orig./MM) [de

  5. INFLUENCE OF HEAT TREATMENT ON THE MICROSTRUCTURE AND TOUGHNESS OF BÖHLER M333 ISOPLAST STEEL

    OpenAIRE

    Perko, J.; Redl, C.; Leitner, H.

    2009-01-01

    In this work the through hardenability and the influence of the heat treatment parameters (austenitizingtemperature, cooling parameter ? and tempering temperature) on the microstructure and the achievabletoughness level of Böhler M333 ISOPLAST are investigated. The results are compared to the standardizedtool steel grade DIN 1.2083. The investigations showed that the cooling parameter ? has a strong influenceon the impact toughness of M333 ISOPLAST plastic mould steel. The toughness is reduce...

  6. Creep behaviour and microstructure of the ferritic material No. 1-6770 under irradiation

    International Nuclear Information System (INIS)

    Herschbach, K.; Ehrlich, K.; Materna, E.

    Creep behaviour under irradiation of the ferritic steel-DIN-1-6770 is quite different of austenitic steel behaviour, in particular temperature sensitivity is important and response to stress is non linear. The microstructure stays unchanged

  7. sajad hussain din

    Indian Academy of Sciences (India)

    Home; Journals; Bulletin of Materials Science. SAJAD HUSSAIN DIN. Articles written in Bulletin of Materials Science. Volume 39 Issue 7 December 2016 pp 1753-1761. Influence of boron doping on mechanical and tribological properties in multilayer CVD-diamond coating systems · SAJAD HUSSAIN DIN M A SHAH N A ...

  8. Conversion electron Moessbauer and XPS study on the effect of polishing of a stainless steel sample

    International Nuclear Information System (INIS)

    Vertes, Cs.; Kuzmann, E.; Lakatos-Varsanyi, M.; Vertes, A.; Vass, G.; Romhanyi, K.

    1994-01-01

    Conversion electron Moessbauer spectroscopy (CEMS) and XPS has been used for the surface analysis of an 'X10CrNiTi 18/9 (DIN 1.7440)'-type stainless steel in order to determine the supposed structural and/or chemical changes in the surface layer caused by polishing. Both, CEMS and XPS results can be associated with the appearance of Fe nitride in the outer layer of steel samples after polishing, while no sing of nitrogen was detected in the bulk material. (author) 9 refs.; 3 figs.; 1 tab

  9. Creep-rupture-test on the stainless steel X6crni1811 (Din 1.494.8) in the frame of the Extrapolation-Program. (Part III); Ensayos de fluencia lenta en el acero inoxidable X6 Cr Ni 1811 (1.4948) en el marco del Programa Extrapolacion

    Energy Technology Data Exchange (ETDEWEB)

    Solano, R; Schirra, M; Rivas, M de la; Barroso, S; Seith, B

    1982-07-01

    The austenitic stainless steel X6crni1811 (Din 1.4948) used as a structure material for the German Fast Breeder Reactor SNR 300 was creep tested in a temperature range of 550-650 degree centigree material condition as well as welded material condition. The main point of this program (Extrapolation-Program) lies in the knowledge of the creep-rupture-strength and creep-behaviour up to 3 x 10{sup 4} hours higher temperatures in order to extrapolated up to {>=}10{sup 5} hours for operating temperatures. In order to study the stress dependency of the minimum creep rate additional tests were carried out of 550 degree centigree - 750 degree centigree. The present report describes the state in the running program with test-times of 23.000 hours and results from tests up to 55.000 hours belonging to other parallel programs are taken into account. Besides the creep-rupture behaviour it is also made a study of ductility between 550 and 750 degree centigree. Extensive metallographic examinations have been made to study the fracture behaviour and changes in structure. (Author)

  10. Increase of volume swelling by a temperature gradient

    International Nuclear Information System (INIS)

    Herschbach, K.; Schneider, W.; Stober, T.

    1996-11-01

    The temperature gradient in the cladding of a Fast Reactor fuel pin leads to increased dilatation compared to material irradiations. Investigations of a specially designed fuel pin reached the conclusion that the cause is enhanced volume swelling. It is induced by He-bubbles, which migrate upwards the temperature gradient and coalesce. The critical size of nuclei for void swelling is thus reached much faster. Consequently, the p in deformation is larger than expected from materials irradiations, in the present case (DIN 1.4981 sa) by about 50%. (orig.) [de

  11. Influence of TiC precipitation in austenitic stainless steel on strength, ductility and helium embrittlement

    International Nuclear Information System (INIS)

    Kesternich, W.; Matta, M.K.; Rothaut, J.

    1984-01-01

    Creep experiments were performed on 1.4970 (German DIN standard) and 316 (AISI standard) type austenitic steels after various thermomechanical pretreatments and after α-implantation. The microstructure introduced by the pretreatments was characterized by transmission electron microscopy and the behaviour of strength and ductility is correlated to the dislocation and precipitate distributions. He embrittlement can be suppressed in these simulation experiments when dispersive TiC precipitate distributions are produced by the proper pretreatments or are allowed to form during creep testing. It is shown that adequate pretreatment results in a significantly superior behaviour of the 1.4970 steel as compared to the 316 type steel in all three investigated properties, i.e. strength, ductility and resistance to He embrittlement. (orig.)

  12. Effect of heat treatment, with and without mechanical work, on the tensile and creep behaviour at 6000C of austenitic stainless steel stabilised with titanium

    International Nuclear Information System (INIS)

    Padilha, A.F.

    1983-01-01

    The effect of various heat treatments, with and without mechanical work, on the microstructure and the tensile and creep behaviour at 600 0 C of the titanium stabilised austenitic stainless steel DIN 1.4970, as well as the effects of aging temperature, pre-strain and small boron additions on the creep behaviour of these steels are discussed. The most probable mechanism is suggested. (Author) [pt

  13. Substitution of modified 9 Cr-1 Mo steel for austentic stainless steels

    International Nuclear Information System (INIS)

    Sikka, V.K.

    1982-04-01

    This report describes the current program to develop a high-strength ferritic-martensitic steel. The alloy is essentially Fe-9% Cr-1% Mo with small additions of V and Nb and is known as modifed 9 Cr-1 Mo steel. Its elevated-temperature properties and design allowable stresses match those of type 304 stainless steel for temperatures up to 600 0 C and exceed those of other ferritic steels by factors of 2 to 3. The improved strength of this alloy permits its use in place of stainless steels for many applications

  14. The formation of hydrogen permeation barriers on steels by aluminising

    Science.gov (United States)

    Forcey, K. S.; Ross, D. K.; Wu, C. H.

    1991-06-01

    An extensive investigation has been carried out into the effectiveness of aluminised layers as permeation barriers on AISI 316L stainless and DIN 1.4914 martensitic steels. The study involved measurement of the hydrogen permeation rate through commercially aluminised steel discs of thicknesses in the range 1-1.6 mm, at temperatures between 250 and 600 °C and for an upstream hydrogen pressure of 10 5 Pa. The composition and structure of the aluminide layers were investigated by a number of techniques such as SEM, electron beam microprobe and X-ray diffraction. Accelerator based techniques such as RBS and NRA were employed to study the top micron or so of the surfaces of the samples. By these techniques it was found that the effectiveness of the permeation barrier depended on the formation of a thin surface oxide layer consisting of Al 2O 3. It was found that the permeation rate through the aluminised steels could be reduced by 3-4 orders of magnitude by forming a surface oxide layer up to a micron or so in thickness.

  15. A microstructural comparison of two nuclear-grade martensitic steels using small-angle neutron scattering

    Science.gov (United States)

    Coppola, R.; Fiori, F.; Little, E. A.; Magnani, M.

    1997-06-01

    Results are presented of a small-angle neutron scattering (SANS) study on two 10-13% Cr martensitic stainless steels of interest for nuclear applications, viz. DIN 1.4914 (MANET specification, for fusion reactors) and AISI 410. The investigation has focussed principally on microstructural effects associated with the differences in chromium content between the two alloys. The size distribution functions determined from nuclear and magnetic SANS components for the two steels given identical heat treatments are in accord with an interpretation based on the presence of ˜ 1 nm size CCr aggregates in the microstructure. Much larger (˜ 10 nm) scattering inhomogeneities with different magnetic contrast are also present and tentatively identified as carbides.

  16. The Effects of The Industrial Cryogenic Process on The Wear Behaviours of AISI D2 Cold Work Tool Steels

    OpenAIRE

    Ersöz, Enes; Ovalı, İsmail

    2018-01-01

    In this study, industrial cryogenic process afterconventional heat treatment process for various holding time was applied toAISI D2 (DIN 1.2379) cold work tool steel. The effects of the industrialcryogenic process on the wear behavior was investigated. In the wear test 5,10and 15 N forces were carried out to all group specimens at a constant shearrate (3,16 m/s) and three different wear distances. Experimental results showthat cryogenic processing of AISI D2 cold work tool steels have a signi...

  17. Sodium corrosion tests in the ML 1 circuit

    International Nuclear Information System (INIS)

    Borgstedt, H.U.

    1977-01-01

    In the ML-1 circuit of the 'Juan Vigon' research centre in Madrid, sodium corrosion tests are being carried out on the austenitic steels DIN 1.4970 (X10NiCrMoTiB1515) and DIN 1.4301 (X5CrNi189) at temperatures between 500 and 700 0 C. The exposure time of the samples amounts to 6,000 h by now. Every 1,000 h, the samples were weighed in order to measure corrosion and deposition effects. After 3,000 and 6,000 h, some selected samples were destroyed for inspection. The results are given. (GSC) [de

  18. Monitoring of Fatigue Degradation in Austenitic Stainless Steels

    International Nuclear Information System (INIS)

    Kalkhof, D.; Niffenegger, M.; Leber, H.J.

    2004-01-01

    During cyclic loading of austenitic stainless steel, it was observed that microstructural changes occurred; these affect both the mechanical and physical properties of the material. For certain steels, a strain-induced martensite phase transformation was seen. The investigations showed that, for the given material and loading conditions, the volume fraction of martensite depends on the cycle number, temperature and initial material state. It was also found that the martensite content continuously increased with the cycle number. Therefore, the volume fraction of martensite was used as an indication of fatigue usage. It was noted that the temperature dependence of the martensite formation could be described by a Boltzmann function, and that the martensite content decreased with increasing temperature. Two different heats of the austenitic stainless steel X6CrNiTi18-10 (AISI 321, DIN 1.4541) were investigated. It was found that the martensite formation rate was much higher for the cold-worked than for the solution-annealed material. All applied techniques - neutron diffraction and advanced magnetic methods - were successful in detecting the presence of martensite in the differently fatigued specimens. (author)

  19. The microstructural stability and mechanical properties of two low activation martensitic steels

    International Nuclear Information System (INIS)

    Victoria, M.; Marmy, P.; Batawi, E.; Peters, J.; Briguet, C.; Rezai-Aria, F.; Gavillet, D.

    1996-01-01

    A desirable feature of future magnetically confined fusion reactors is the prospect of producing low level radioactive waste. In order to minimize the volume of radioactive material, in particular from the first wall and blanket structures, reduced long term activation alloys are being developed. Here, a low activation composition of a martensitic 9% Cr steel has been studied, based on the DIN (Deutsches Inst. fuer Normung) 1.4914 composition (MANET) but replacing Ni, Mo and Nb by the low activation elements W, V and Ta. Two casts were produced from high purity components, in which the effects of controlled additions of Mn (0.58 and 0.055 wt. %) and N (7 and 290 wt. ppm) were studied, so that the final compositions resulted in one cast with high Mn and low N (steel A) and the other with the opposite conditions (steel B). The two steels were evaluated in terms of structural stability and mechanical properties under tensile, fatigue and fracture toughness tests. It has been found that both alloys have a DBTT below room temperature, which in the case of the steel A is 70 K below that of MANET. Although the tensile strength is somewhat below that of the parent steel, both steels have longer fatigue life

  20. DInSAR time series generation within a cloud computing environment: from ERS to Sentinel-1 scenario

    Science.gov (United States)

    Casu, Francesco; Elefante, Stefano; Imperatore, Pasquale; Lanari, Riccardo; Manunta, Michele; Zinno, Ivana; Mathot, Emmanuel; Brito, Fabrice; Farres, Jordi; Lengert, Wolfgang

    2013-04-01

    One of the techniques that will strongly benefit from the advent of the Sentinel-1 system is Differential SAR Interferometry (DInSAR), which has successfully demonstrated to be an effective tool to detect and monitor ground displacements with centimetre accuracy. The geoscience communities (volcanology, seismicity, …), as well as those related to hazard monitoring and risk mitigation, make extensively use of the DInSAR technique and they will take advantage from the huge amount of SAR data acquired by Sentinel-1. Indeed, such an information will successfully permit the generation of Earth's surface displacement maps and time series both over large areas and long time span. However, the issue of managing, processing and analysing the large Sentinel data stream is envisaged by the scientific community to be a major bottleneck, particularly during crisis phases. The emerging need of creating a common ecosystem in which data, results and processing tools are shared, is envisaged to be a successful way to address such a problem and to contribute to the information and knowledge spreading. The Supersites initiative as well as the ESA SuperSites Exploitation Platform (SSEP) and the ESA Cloud Computing Operational Pilot (CIOP) projects provide effective answers to this need and they are pushing towards the development of such an ecosystem. It is clear that all the current and existent tools for querying, processing and analysing SAR data are required to be not only updated for managing the large data stream of Sentinel-1 satellite, but also reorganized for quickly replying to the simultaneous and highly demanding user requests, mainly during emergency situations. This translates into the automatic and unsupervised processing of large amount of data as well as the availability of scalable, widely accessible and high performance computing capabilities. The cloud computing environment permits to achieve all of these objectives, particularly in case of spike and peak

  1. Não-linearidades: da dinâmica do simples à dinâmica do complexo

    Directory of Open Access Journals (Sweden)

    José Roberto Castilho Piqueira

    1994-01-01

    Full Text Available Foram apresentados alguns conceitos relativos à utilização da Teoria dos Sistemas Dinâmicos em problemas de sistemas complexos. A apresentação destes conceitos centra-se no estabelecimento de duas dinâmicas: uma de curto termo e outra de longo termo, relacionando-as com os processos de organização dos sistemas.

  2. European development of ferritic-martensitic steels for fast reactor wrapper applications

    International Nuclear Information System (INIS)

    Bagley, K.; Little, E.A.; Levy, V.; Alamo, A.

    1987-01-01

    9-12%Cr ferritic-martensitic stainless steels are under development in Europe for fast reactor sub-assembly wrapper applications. Within this class of alloys, attention is focussed on three key specifications, viz. FV448 and DIN 1.4914 (both 10-12%CrMoVNb steels) and EM10 (an 8-10%Cr-0.15%C steel), which can be optimized to give acceptably low ductile-brittle transition characteristics. The results of studies on these steels, and earlier choices, covering heat treatment and compositional optimization, evolution of wrapper fabrication routes, pre and post-irradiation mechanical property and fracture toughness behaviour, microstructural stability, void swelling and in-reactor creep characteristics are reviewed. The retention of high void swelling to displacement doses in excess of 100 dpa in reactor irradiations reaffirms the selection of 9-12%Cr steels for on-going wrapper development. Moreover, irradiation-induced changes in mechanical properties (e.g. in-reactor creep and impact behaviour), measured to intermediate doses, do not give cause for concern; however, additional data to higher doses and at the lower irradiation temperatures of 370 0 -400 0 C are needed in order to fully endorse these alloys for high burnup applications in advanced reactor systems

  3. Electrochemical studies of the corrosion behavior of a low-carbon steel in aqueous chloride solutions simulating accident conditions of radioactive waste disposal

    International Nuclear Information System (INIS)

    Farvaque-Bera, A.M.; Leistikow, S.

    1991-01-01

    The fine-grained structural steel DIN W.Nr. 1.0566 was exposed to various sulfate and chloride-containing aqueous solutions, the latter ones simulating the potential accidental environment of water intrusion into a salt mine. By electrochemical measurements in salt brines, the following results were achieved: (1) The corrosion rate is highly dependent on salt brine composition, pH and temperature. (2) Active metal dissolution led to formation of shallow pits as surface corrosion phenomenon. Thus, the application of electrochemical techniques - under non-polarized as well as under potentiodynamic conditions - proved to be suitable for fast qualitative testing of the influence of various environmental parameters on steel corrosion. (orig.)

  4. [DIN-compatible vision assessment of increased reproducibility using staircase measurement and maximum likelihood analysis].

    Science.gov (United States)

    Weigmann, U; Petersen, J

    1996-08-01

    Visual acuity determination according to DIN 58,220 does not make full use of the information received about the patient, in contrast to the staircase method. Thus, testing the same number of optotypes, the staircase method should yield more reproducible acuity results. On the other hand, the staircase method gives systematically higher acuity values because it converges on the 48% point of the psychometric function (for Landolt rings in eight positions) and not on the 65% probability, as DIN 58,220 with criterion 3/5 does. This bias can be avoided by means of a modified evaluation. Using the staircase data we performed a maximum likelihood estimate of the psychometric function as a whole and computed the acuity value for 65% probability of correct answers. We determined monocular visual acuity in 102 persons with widely differing visual performance. Each subject underwent four tests in random order, two according to DIN 58,220 and two using the modified staircase method (Landolt rings in eight positions scaled by a factor 1.26; PC monitor with 1024 x 768 pixels; distance 4.5 m). Each test was performed with 25 optotypes. The two procedures provide the same mean visual acuity values (difference less than 0.02 acuity steps). The test-retest results match in 30.4% of DIN repetitions but in 50% of the staircases. The standard deviation of the test-retest difference is 1.41 (DIN) and 1.06 (modified staircase) acuity steps. Thus the standard deviation of the single test is 1.0 (DIN) and 0.75 (modified staircase) acuity steps. The new method provides visual acuity values identical to DIN 58,220 but is superior with respect to reproducibility.

  5. Density of Liquid Steel over Temperature Range of 1 803-1 873 K

    Institute of Scientific and Technical Information of China (English)

    XIAO Feng; FANG Liang

    2004-01-01

    The density of three kinds of liquid steel was measured by a modified sessile drop method over the temperature range of 1 803-1 873 K. It is found that the density of liquid steels decreases with increasing temperature and carbon content in steel. Both of the density and its absolute temperature coefficient of studied steels are smaller than the literature values of pure iron. The molar volume of the steels increases with increasing temperature.

  6. Ensayo sobre endurecimiento de adhesivos estructurales sometidos a cargas dinámicas

    Directory of Open Access Journals (Sweden)

    Recuero, A.

    2004-04-01

    Full Text Available Carbon fibre reinforced polymers are increasingly replacing the steel reinforcing systems in the repair and strengthening of concrete structures thanks to their high strength/weight and stiffness/weight ratios, corrosion resistance, lightweight, and ease of handling and application. This paper presents a study on the behaviour of bridge concrete beams strengthened with CFRP sheets when the strengthening is made when traffic is acting so that the structure is subjected to dynamic loads while the adhesive is still fresh. No reduction in the effectiveness of the strengthening was observed in the tests.

    Los polímeros reforzados con fibras de carbono se están utilizando cada vez más para el refuerzo de estructuras de hormigón, reemplazando a los sistemas tradicionales de refuerzo con acero. Esto es debido a sus altas resistencia y rigidez específicas, resistencia a la corrosión, ligereza y facilidad de manejo y puesta en obra. Este artículo presenta un estudio sobre el comportamiento de vigas de puentes reforzadas con bandas de CFRP mientras se mantiene el puente en servicio de manera que la estructura está sometida a cargas dinámicas con el adhesivo fresco. En los ensayos realizados se ha observado que las cargas dinámicas no afectan a la efectividad del refuerzo.

  7. DINS measurements on VESUVIO in the Resonance Detector configuration: proton mean kinetic energy in water

    Science.gov (United States)

    Pietropaolo, Antonino; Andreani, Carla; Filabozzi, Alessandra; Senesi, Roberto; Gorini, Giuseppe; Perelli-Cippo, Enrico; Tardocchi, Marco; Rhodes, Nigel J.; Schooneveld, Erik M.

    2006-04-01

    Deep Inelastic Neutron Scattering (DINS) measurements have been performed on a liquid water sample at two different temperatures and pressures. The experiments were carried out using the VESUVIO spectrometer at the ISIS spallation neutron source. This experiment represents the first DINS measurement from water using the Resonance Detector configuration, employing yttrium-aluminum-perovskite scintillator and a 238U analyzer foil. The maximum energy of the scattered neutrons was about 70 eV, allowing to access an extended kinematic space with energy and wave vector transfers at the proton recoil peak in the range 1 eV <= hbarω <= 20 eV and 25 Å-1 <= q <= 90 Å-1, respectively. Comparison with DINS measurements on water performed in the standard Resonance Filter configuration indicates the potential advantages offered by the use of Resonance Detector approach for DINS measurements at forward scattering angles.

  8. ALERGENUL ARA H3, GLOBULINA DE REZERVĂ 11S DIN SEMINŢELE DE ARAHIDE 1. PROTEOLIZA LIMITATĂ CU PAPAINĂ

    Directory of Open Access Journals (Sweden)

    Ala CHERDIVARĂ

    2017-07-01

    Full Text Available Proteoliza globulinei de rezervă 11S din seminţele de arahide, Ara h3, cu papaină începe cu cuscindarea secvenței C-terminale extinse a α-catenelor, care cuprinde regiunea α-helixurilor. Clivarea ulterioară a buclei dintre β-strendurile E' şi F' din partea centrală a β-barrelui din α-catene duce la formarea fragmentelor, legate cu β-catenele intacte prin legătură disulfidică, precum şi reţinute în molecula globulinei 11S parţial hidrolizată prin interacţiuni necovalente. Conform scenariului proteolizei descrise, acţiunea iniţială a papainei distruge regiunea C-terminală a α-catenelor, în care sunt prezenţi trei din cei patru determinanţi antigenici (epitopii IgE, identificaţi în globulina 11S din arahide. Astfel, gradul de alergenicitate a Ara h3 poate fi substanțial redus prin proteoliza sa limitată cu papaină.ALLERGEN ARA H3, STORAGE 11S GLOBULIN FROM PEANUT SEEDS 1. PAPAIN LIMITED PROTEOLYSISPapain proteolysis of the storage 11S globulin Ara h3 from peanut seeds starts from the detachment of an extended a-chain C-terminal sequence covering the region of a-helices. Further cleavage of a loop between b-strands E’ and F’ inside the central part of a-chain b-barrel occurs generating fragments connected with intact b-chains via a disulfide bond and those retained inside the molecule of partially hydrolyzed 11S globulin due to non-covalent interactions. In accordance with the described proteolysis scenario, the C-terminal a-chain region containing three of the four antigen determinants (IgE epitopes identified in the peanut 11S globulin is destroyed during the initial papain action. Therefore, the level of Ara h3 allergenicity can be decreased via papain limited proteolysis.

  9. EXPERIMENTAL RESEARCH REGARDING THE INFLUENCE OF CUTTING REGIME ON THE WEAR OF DRILLS AT STEEL PROCESSING

    Directory of Open Access Journals (Sweden)

    Leonard Marius CIUREZU GHERGHE

    2015-05-01

    Full Text Available This paper aims to highlight the influence of cutting regime on the wear drills at steel processing , in particular the processing of stainless steel X17CrNi16-2 SR EN 10088-4 DIN 17440. We are interested in wear of the drill at processing of this type of stainless steel , which has applicability in energy industry given the special characteristics of its. We want a maximum value of 0.2 mm for the wear of the drill, measurement and taking pictures are made using a microscope DigiMicro 2.0 and the software used is MicroCapture. Processing was done on machining center YMC YOUNG TECH 1050, and the tool used was 8 mm drill bit high speed steel.

  10. Estimation of residual stresses in reactor pressure vessel steel specimens clad by stainless steel strip electrodes

    International Nuclear Information System (INIS)

    Schimmoeller, H.A.; Ruge, J.L.

    1978-01-01

    The equations to determine a two-dimensional state of residual stress in flat laminated plates are well known from an earlier work by one of the authors. The derivation of these equations leads to a linear, inhomogeneous system of Volterra's integral equations of the second kind. To ascertain the unknown residual stresses from these equations it is necessary to cut down the thickness of the test plate layer by layer. This results in two-dimensional deformation reactions in the rest of the test plate, which can be measured, e.g. by a strain gauge rosette applied to the opposite side of the plate. The above-mentioned stress analysis has been transferred to 86mm thick reactor pressure vessel steel specimens (Type 22NiMoCr 37, DIN-No. 1.6751, similar to ASTM A508, Class 2) double-run clad by austenitic stainless steel strip electrodes (first layer 24/13 Cr-Ni steel, second layer 21/10 Cr-Ni steel). The overall dimensions of the clad specimens investigated amounted to 200 x 200 x (86+4.5+4.5)mm. At the surface of the austenitic cladding there is a two-dimensional tensile normal stress state of about 200N/mm 2 parallel, and about 300N/mm 2 transverse, to the welding direction. The maximum tensile stress was 8mm below the interface (fusion line, material transition) in the parent material. The stress distributions of the specimens investigated, determined on the basis of the above-mentioned combined experimental mathematical procedure, are presented graphically for the as-welded (as-delivered) and annealed (600 0 C/12hr) conditions. (author)

  11. Topic 1. Steels for light water reactor pressure vessels

    International Nuclear Information System (INIS)

    Brumovsky, M.; Brynda, J.; Kepka, M.; Barackova, L.; Vacek, M.; Havel, S.; Cukr, B.; Protiva, K.; Petrman, I.; Tvrdy, M.; Hyspecka, L.; Mazanec, K.; Kupca, L.; Brezina, M.

    1980-01-01

    Part 1 of the Proceedings consists of papers on the criteria for the selection and comparison of the properties of steel for pressure vessels and on the metallurgy of the said steels, the selection of suitable material for internal tubing systems, the manufacture of high-alloy steels for WWER components, the mechanical and metallurgical properties of steel 22K for WWER 440 pressure components, and of steel 10MnNi2Mo for the WWER primary coolant circuit, and the metallographic assessment of steel 0Kh18N10T. (J.P.)

  12. Nitrided steel 38CrN3MAFA for supporting elements in nuclear power plants; Vysokoazotistaya stal` tipa 38HN3MAFA dlya krepezhnikh detajlej reaktorov AEhS

    Energy Technology Data Exchange (ETDEWEB)

    Rasheva, I; Argirov, Kh; Stojchev, T [Bylgarska Akademiya na Naukite, Sofia (Bulgaria). Inst. po Metaloznanie i Tekhnologiya na Metalite

    1996-12-31

    Nitride doping of steel at different concentrations is achieved by counter-pressure casting in nitrogen ambience. A new type of steel is developed containing 0.05-0.2% N{sub 2}. It is compared to a standard 34NiCrMoV145 steel (DIN). The mechanical properties are improved significantly after a two-stage thermal treatment and are as follows: fluidity limit R{sub 0}.2>=1045 MPa, relative elongation A>=15%, relative shortening Z>=62%, impact viscosity KCU >= 1 MJ/m{sup 2}. The quench hardening consists of heating to 800-850{sup o} C in oil and cooling to 600{sup o} C in air. The steel is suitable for rotors, turbines, compressor shafts and reactor supporting elements in nuclear power plants. 3 refs., 6 figs., 6 tabs.

  13. Isothermal steam oxidation of the ferritic 11% Cr steel (DIN No. 1.4914) at 900 to 13000C

    International Nuclear Information System (INIS)

    Zurek, Z.

    1982-11-01

    The steam oxidation of ferritic 11% Cr steel tube and sheet samples at 900 to 1300 0 C has been studied gravimetrically, metallographically, by X-ray diffraction and in detail by electron probe microanalysis. The reaction rate could be described by parabolic kinetics of mass increase. During the oxidation a three-layer scale was formed on the surface. The inner layer was composed of iron-chromium spinel, the intermediate layer consisted of a mixture wustite and magnetite, the very thin outer layer was composed of magnetite. Within the inner scale layer small metallic particles enriched of nickel could be observed. The scale cohesion was generally poor for tube as well as for sheet material and was improving with oxidation time and temperature. After oxidation Pt-markers indicated the growth of inner and outer layer in relation to the initial metal surface. The sheet material specimens exposed at 1000-1100 0 C had blisters on their surfaces. A swelling of about 12-15% was measured for the oxidized tubing. Isotherme Dampf-Oxidation des ferritischen 11% Cr-Stahls (Werkstoff Nr. 1.4914) bei 900 - 1300 0 C. (orig.) [de

  14. Ernst Rüdin, 1874-1952: a German psychiatrist and geneticist.

    Science.gov (United States)

    Weber, M M

    1996-07-26

    Ernst Rüdin (1874-1952) was one of the major representatives of German psychiatry, genetics, and eugenics in the first half of the twentieth century. Born in Switzerland, he was influenced early on by his brother-in-law Alfred Ploetz, who propagated the ideas of social Darwinism and "racial hygiene" in Germany after 1890. Rüdin began his career in psychiatry at Emil Kraepelin's clinic in Munich, where he developed the concept of "empirical genetic prognosis" of mental disorders. He published his first results on the genetics of schizophrenia in 1916. From 1917-1945 Rüdin was director of the Genealogical-Demographic Department at the German Institute for Psychiatric Research, which Kraepelin had founded. After a short interruption from 1925-1928, Rüdin returned to Munich and enlarged the department. After 1933 the National Socialist government and party endorsed Rüdin's work by supplying financial and manpower support. Nazi health policy required a scientific basis to justify its actions, and Rüdin's ideas corresponded partially with this kind of thinking. In 1934 he prepared the official commentary on the "Law for the Prevention of Genetically Diseased Offspring." The connections of Rüdin's department to National Socialism can be understood as one of the main reasons for the critical attitude towards psychiatric genetics in Germany after 1945.

  15. A novel cis-acting element required for DNA damage-inducible expression of yeast DIN7

    International Nuclear Information System (INIS)

    Yoshitani, Ayako; Yoshida, Minoru; Ling Feng

    2008-01-01

    Din7 is a DNA damage-inducible mitochondrial nuclease that modulates the stability of mitochondrial DNA (mtDNA) in Saccharomyces cerevisiae. How DIN7 gene expression is regulated, however, has remained largely unclear. Using promoter sequence alignment, we found a highly conserved 19-bp sequence in the promoter regions of DIN7 and NTG1, which encodes an oxidative stress-inducible base-excision-repair enzyme. Deletion of the 19-bp sequence markedly reduced the hydroxyurea (HU)-enhanced DIN7 promoter activity. In addition, nuclear fractions prepared from HU-treated cells were used in in vitro band shift assays to reveal the presence of currently unidentified trans-acting factor(s) that preferentially bound to the 19-bp region. These results suggest that the 19-bp sequence is a novel cis-acting element that is required for the regulation of DIN7 expression in response to HU-induced DNA damage

  16. Characterization of sensitization and stress corrosion cracking behavior of stabilized stainless steels under BWR conditions

    International Nuclear Information System (INIS)

    Kilian, R.; Ilg, U.; Meier, V.; Teichmann, H.; Wachter, O.

    1995-01-01

    Stress corrosion cracking occurs if the three parameters -- material condition, tensile stress and water chemistry -- are in a critical range. In this study the material conditions especially of Ti- and Nb-stabilized steels are considered. The purpose of this work is to show the influence of the degree of sensitization of Ti- and Nb-stabilized stainless steels on stress corrosion cracking susceptibility in BWR water chemistry. This is an on-going research program. Preliminary results will be presented. Different types of stabilized, and for comparison unstabilized, stainless steels are examined in various heat treatment conditions with regard to their sensitization behavior by EPR tests (double loop) and TEM. The results are plotted in sensitization diagrams. The sensitization behavior depends on many parameters such as carbon content, stabilization element, stabilization ratio and materials history, e.g. solution heat treatment or cold working. The obtained EPR sensitization diagrams are compared with the well known sensitization diagrams from the literature, which were determined by standard IC test according to e.g. German standard DIN 50914 (equivalent to ASTM A 262, Pract. E). Based on the obtained EPR sensitization diagrams material conditions for SSRT tests were selected. The EPR values (Ir/Ia x 100%) of the tested Ti-stabilized stainless steel are in the range of ∼ 0.1--20%. The SSRT tests are carried out in high-temperature water with 0.4 ppm O 2 , a conductivity of 0.5 microS/cm and a strain rate of 1x10 -6-1 . The test temperature is 280 C. Ti-stabilized stainless steel with Ir/Ia x 100% > 1% suffered intergranular stress corrosion cracking under these conditions. The SCC tests for Nb-stabilized stainless steel are still in progress. The correlation between EPR value, chromium depletion and SSRT result will be shown for a selected material condition of sensitized Ti-stabilized stainless steel

  17. Entrenamiento integrado. Principios dinámicos y aplicaciones

    Directory of Open Access Journals (Sweden)

    Natàlia Balagué Serre

    2014-06-01

    Full Text Available El interés por el entrenamiento integrado es creciente y para aumentar su eficacia resulta clave conocer cómo se produce el proceso de integración en los sistemas vivos. Por lo general, se suele asumir que el tipo de integración que se da en el organismo y entre los componentes del entrenamiento es sumatoria y lineal; es decir, está caracterizada por relaciones proporcionales, fijas e invariables en el tiempo, como las que se dan en cualquier artilugio técnico. Este modelo de integración, basado en la cibernética clásica, contrasta con el modelo de integración dinámica y no lineal, asentado en la neurociencia, la teoría de sistemas dinámicos no lineales, y la dinámica ecológica. Algunos principios de la integración dinámica y no lineal como la autoorganización, su carácter no proporcional y no consciente y su integración contextual en diferentes escalas acostumbran a ignorarse sistemáticamente en las metodologías de entrenamiento más habituales. El objetivo de este trabajo es presentar los principios dinámicos del entrenamiento integrado para promover la emergencia de metodologías más eficaces y eficientes a la vez que más respetuosas con los deportistas y los equipos.

  18. Seasonal and multi-year surface displacements measured by DInSAR in a High Arctic permafrost environment

    Science.gov (United States)

    Rudy, Ashley C. A.; Lamoureux, Scott F.; Treitz, Paul; Short, Naomi; Brisco, Brian

    2018-02-01

    Arctic landscapes undergo seasonal and long-term changes as the active layer thaws and freezes, which can result in localized or irregular subsidence leading to the formation of thermokarst terrain. Differential Interferometric Synthetic Aperture Radar (DInSAR) is a technique capable of measuring ground surface displacements resulting from thawing permafrost at centimetre precision and is quickly gaining acceptance as a means of measuring ground displacement in permafrost regions. Using RADARSAT-2 stacked DInSAR data from 2013 and 2015 we determined the magnitude and patterns of land surface change in a continuous permafrost environment. At our study site situated in the Canadian High Arctic, DInSAR seasonal ground displacement patterns were consistent with field observations of permafrost degradation. As expected, many DInSAR values are close to the detection threshold (i.e., 1 cm) and therefore do not indicate significant change; however, DInSAR seasonal ground displacement patterns aligned well with climatological and soil conditions and offer geomorphological insight into subsurface processes in permafrost environments. While our dataset is limited to two years of data representing a three-year time period, the displacements derived from DInSAR provide insight into permafrost change in a High Arctic environment and demonstrate that DInSAR is an applicable tool for understanding environmental change in remote permafrost regions.

  19. DIN VIAŢĂ SI DIN CĂRŢI O LUCRARE CE NE PUNE PE GÂNDURI

    Directory of Open Access Journals (Sweden)

    Coriolan PĂUNESCU

    2008-06-01

    Full Text Available A apărut, la Iasi, o carte cu valoare de unicat; este vorba de „Agriculturaîn proverbe si cugetări” (Ed. Vasiliana ’98, Iasi, 2008, semnată de reputatul Prof.univ. dr. Nicolae VASILESCU si ing. Aglaia VASILESCU, oameni care au slujitdecenii de-a rândul învăţământul agronomic românesc. De aici, desigur si respectulautorilor pentru agricultură si, mai ales, pentru oamenii satului, dedicaţi, înîntregime, acestei nobile îndeletniciri (dar si creaţiei lor spirituale, în care, nu o dată,se reflectă munca si viaţa de fiecare zi. Însă, această carte se vrea mai mult decâtspune, deoarece cuprinde si reflecţii ale oamenilor culţi, despre agricultură, întrecare scriitori, filosofi, muzicieni, savanţi ai domeniului agronomic, călătoriînvederaţi, politicieni, istorici, oameni ai catedrelor, revoluţionari de renume,evident, din lume si din ţară, din Antichitate si până astăzi.

  20. Carbon transfer between 2 1/4 Cr 1 Mo alloy and austenitic steels (experiments in anisothermal loops)

    International Nuclear Information System (INIS)

    Baque, P.; Besson, M.; Champeix, L.; Donati, J.R.; Oberlin, C.; Saint-Paul, P.

    1976-01-01

    Studies on carbon transfer between the ferritic steel 2 1/4 Cr 1 Mo and the austenitic steels 316L and 321H have shown that there is not any measurable carbon transfer in the operating conditions of the secondary circuit of PHENIX (475 deg C was the maximal temperature of the 2 1/4 Cr 1 Mo steel). A significant carbon transfer has been observed between the ferritic steel and the 316L steel when the 321H was replaced by the 2 1/4 Cr 1 Mo steel in the same thermohydraulic conditions (the ferritic steel was then used up to 545 deg C). This experiment has demonstrated the importance of the temperature and the initial carbon content of the ferritic steel as parameters in the decarburization process. It appears that decarburization may not be sensitive to the thermohydraulic conditions at least in the range investigated in those experiments. In the other hand the 316L steel is observed to have been carburized, the degree of carburization remaining appreciably constant and independent on the temperature between 400 deg C and 550 deg C [fr

  1. On the Cutting Performance of Coated HSS Taps When Machining of Austenitic Steel

    Science.gov (United States)

    Sliwkova, Petra; Piska, Miroslav

    2014-12-01

    The paper deals with a quality of the PVD coated HSS taps when cutting the stainless austenitic chromiumnickel non-stabilized steel DIN 1.4301 (X5CrNi 18-10). The main attention is focused on the analysis of loading (cutting moment, specific energy) of the HSS taps by means of pieso-electrical dynamometer Kistler 9272 and the relation between the quality of duplex and triplex PVD coatings and their effects on the quality of machined thread surfaces and tool life of the taps. The results showed a safe and stabilized cutting with acceptable quality of threads for HSSE with the TiN+TiCN+DLC coating.

  2. characterization and weldability of plasma nitrided P/M martensitic stainless steel X 20 Cr Ni 172

    International Nuclear Information System (INIS)

    Abdel-Karim, R.A.; El-demellawy, M.A; Waheed, A.F.

    2004-01-01

    stainless steels are widely used in nuclear applications, as a construction material. in these applications stainless steels suffer from corrosion degradation due severe environment and operating conditions. improving the engineering properties of such material prolong the service life time.in the present study, powder metallurgy technique namely plasma rotating electrode process (PREP) was used to produce martensitic steel DIN X 20 Cr Ni 172 with 0.5 % N. this step was followed by hot isostatic pressing process (HIP) . the effect of N on the weldability of this steel has been investigated . this included microstructure characterization, hardness evaluation and ferrite content measurements. the results showed that the presence of high nitrogen content in this steel resulted in a pore free structure with improved the hardness across the welding area. A single phase with few precipitates was detected on the grain boundaries in the heat affected zone. the results were supplemented by x-ray diffraction patterns and EDAX analysis

  3. Duygusal Zeka Din Öğretimi; Din Kültürü ve Ahlak Bilgisi Dersi ve Duygusal Zeka Gelişim İlişkisi

    Directory of Open Access Journals (Sweden)

    Remziye Ege

    2015-11-01

    Full Text Available Duygusal zeka, bireyin, kendi duygularını anlaması, başkalarıın duygularına empati  beslemesi, duygu yönetimi, motivasyon ve duygularını yaşamı zenginleştirecek biçimde düzenleyebilme yetisi olarak tanımlanmaktadır. Din öğretimi yoluyla duygusal zeka becerilerinin ve yerisinin elde edileceği ve geliştirileceği düşünülmektedir. Bu makalede İlköğretim Din Kültürü ve Ahlak Bilgisi Dersinin muhtevasından hareketle duygusal zeka gelişimi ile din öğretimi arasındaki paralel ilişkiye dikkat çekmek hedeflenmiştir. Söz konusu ilişki, din öğretiminin inanç, ibadet, dua, ahlak öğretim alanlarındaki konulardan örnekler üzerinde belirtilmiştir. Duygusal zeka, bireyin, kendi duygularını anlaması, başkalannın duygulanna empati beslemesi, duygu yönetimi, motivasyon ve duygularını yaşamı zenginleştirecek biçimde düzenleyebilme yetisi olarak tanımlanmaktadır. Din öğretimi yoluyla duygusal zeka becerilerinin ve yerisinin elde edileceği ve geliştirileceği düşünülmektedir. Bu makalede İlköğretim Din Kültürü ve Ahlak Bilgisi Dersinin muhtevasından hareketle duygusal zeka gelişimi ile din öğretimi arasındaki paralel ilişkiye dikkat çekmek hedeflenmiştir. Söz konusu ilişki, din öğretiminin inanç, ibadet, dua, ahlak öğretim alanlarındaki konulardan örnekler üzerinde belirtilmiştir

  4. Escherichia coli DinB inhibits replication fork progression without significantly inducing the SOS response.

    Science.gov (United States)

    Mori, Tetsuya; Nakamura, Tatsuro; Okazaki, Naoto; Furukohri, Asako; Maki, Hisaji; Akiyama, Masahiro Tatsumi

    2012-01-01

    The SOS response is readily triggered by replication fork stalling caused by DNA damage or a dysfunctional replicative apparatus in Escherichia coli cells. E. coli dinB encodes DinB DNA polymerase and its expression is upregulated during the SOS response. DinB catalyzes translesion DNA synthesis in place of a replicative DNA polymerase III that is stalled at a DNA lesion. We showed previously that DNA replication was suppressed without exogenous DNA damage in cells overproducing DinB. In this report, we confirm that this was due to a dose-dependent inhibition of ongoing replication forks by DinB. Interestingly, the DinB-overproducing cells did not significantly induce the SOS response even though DNA replication was perturbed. RecA protein is activated by forming a nucleoprotein filament with single-stranded DNA, which leads to the onset of the SOS response. In the DinB-overproducing cells, RecA was not activated to induce the SOS response. However, the SOS response was observed after heat-inducible activation in strain recA441 (encoding a temperature-sensitive RecA) and after replication blockage in strain dnaE486 (encoding a temperature-sensitive catalytic subunit of the replicative DNA polymerase III) at a non-permissive temperature when DinB was overproduced in these cells. Furthermore, since catalytically inactive DinB could avoid the SOS response to a DinB-promoted fork block, it is unlikely that overproduced DinB takes control of primer extension and thus limits single-stranded DNA. These observations suggest that DinB possesses a feature that suppresses DNA replication but does not abolish the cell's capacity to induce the SOS response. We conclude that DinB impedes replication fork progression in a way that does not activate RecA, in contrast to obstructive DNA lesions and dysfunctional replication machinery.

  5. Localized landslide risk assessment with multi pass L band DInSAR analysis

    Science.gov (United States)

    Yun, HyeWon; Rack Kim, Jung; Lin, Shih-Yuan; Choi, YunSoo

    2014-05-01

    In terms of data availability and error correction, landslide forecasting by Differential Interferometric SAR (DInSAR) analysis is not easy task. Especially, the landslides by the anthropogenic construction activities frequently occurred in the localized cutting side of mountainous area. In such circumstances, it is difficult to attain sufficient enough accuracy because of the external factors inducing the error component in electromagnetic wave propagation. For instance, the local climate characteristics such as orographic effect and the proximity to water source can produce the significant anomalies in the water vapor distribution and consequently result in the error components of InSAR phase angle measurements. Moreover the high altitude parts of target area cause the stratified tropospheric delay error in DInSAR measurement. The other obstacle in DInSAR observation over the potential landside site is the vegetation canopy which causes the decorrelation of InSAR phase. Thus rather than C band sensor such as ENVISAT, ERS and RADARSAT, DInSAR analysis with L band ALOS PLASAR is more recommendable. Together with the introduction of L band DInSAR analysis, the improved DInSAR technique to cope all above obstacles is necessary. Thus we employed two approaches i.e. StaMPS/MTI (Stanford Method for Persistent Scatterers/Multi-Temporal InSAR, Hopper et al., 2007) which was newly developed for extracting the reliable deformation values through time series analysis and two pass DInSAR with the error term compensation based on the external weather information in this study. Since the water vapor observation from spaceborne radiometer is not feasible by the temporal gap in this case, the quantities from weather Research Forecasting (WRF) with 1 km spatial resolution was used to address the atmospheric phase error in two pass DInSAR analysis. Also it was observed that base DEM offset with time dependent perpendicular baselines of InSAR time series produce a significant error

  6. Kommunikation skaber din organisation

    DEFF Research Database (Denmark)

    Hansen, Heidi

    KOMMUNIKATION skaber din ORGANISATION tager udgangspunkt i en narrativ tilgang til kommunikation, hvor organisationen skabes i mødet mellem ledere, medarbejdere, organisation og omverden. Historier hjælper os med at skabe mening, og er derfor vigtige både som et udviklingsværktøj i organisationen...

  7. Corrosion critique of the 2 1/4 Cr--1 Mo steel for LMFBR steam generation system applications

    International Nuclear Information System (INIS)

    Zima, G.E.

    1977-07-01

    The unstabilized ferritic steel of nominal composition, 2 1 / 4 Cr-1Mo, has been proposed for critical structural assignments in LMFBR powerplants, specifically: the tubing, tubesheet and shell of the evaporator and superheater components. The interest in this steel has been based on a presumably favorable general corrosion property spectrum, acceptable mechanical properties and fabricability, and certain economies associated with the low alloy content. This report is an attempt at a general corrosion assessment for the 2 1 / 4 Cr-1Mo steel and an identification of corrosion problem areas potential to this steel from the sodium and water/steam systems of the proposed working environment. There is a considerable area of uncertainty in the sodium-side response of 2 1 / 4 Cr-1Mo steel, centered in the loss and redisposition of carbon during long-term exposure to sodium of various impurity backgrounds. It is submitted that present evidence relating to the water/steam-side corrosion behavior of the 2 1 / 4 Cr-1Mo steel, under nominal and conceivable perturbed environmental conditions, constitutes the principal concern for the proposed LMFBR powerplant applications of this steel. It is suggested that this unfavorable corrosion aspect represents an inherent limitation of the low alloy content of this steel, probably largely independent of melting and processing recourses, and it is a sufficient basis to question the incentive for a continuation of the collateral studies of this steel for the proposed LMFBR steam generation system assignments

  8. Una herramienta para la selección automatizada de aceros en el contexto // A tool for the automated selection of steels in the Mechanical Engineering´s context

    Directory of Open Access Journals (Sweden)

    L. Dumitrescu

    2010-01-01

    Full Text Available ResumenEl diseno de Ingenieria de un producto o componente constituye una actividad dificil, compleja ymultidisciplinaria, enfocada a la resolucion de problemas. En el presente trabajo se muestra eldesarrollo de una herramienta automatizada para la seleccion de los aceros mas utilizados en laconstruccion de maquinarias. La herramienta constituye una ayuda para la seleccion de losmateriales desde la etapa conceptual del proceso de diseno, donde se identifican las diferentescategorias de materiales a utilizar. La herramienta comprende las caracteristicas y propiedades masrelevantes de los aceros de Ingenieria disponibles en seis normas internacionales: Japonesa (JIS,Alemana (DIN, Vbn, DIN-Vbn, Rusa (GOST, Americana (AISI, SAE, AISI-SAE, ASTM, Inglesa (BS, EN,GB, Francesa (AFNOR y la Norma Cubana (NC vigente.Palabras claves: materiales, automatizada, aceros, ingenieria.____________________________________________________________AbstractThe product or component design constitutes a difficult, complex and multidisciplinary activity,focused to the resolution of problems. Presently work show the development of an automated toolfor the selection of the more used steels in the construction of machineries. The tool constitute ahelp for the selection of the materials from the conceptual stage of the design process, where thedifferent categories of materials are identified to use. The tool analyze the characteristics and morecommon properties of the available steels in six international standards: JIS (Japan, DIN, Vbn, DINVbn(Germany, GOST (Russia, AISI, SAE, AISI-SAE, ASTM (USA, BS, IN, GB (England, AFNOR(France and NC (Cuba.Key words: materials, automated, steels, engineering.

  9. Comportamento dinâmico de um modelo simples solo-estrutura

    OpenAIRE

    Gonçalves, Fábio André Vaz

    2012-01-01

    Dissertação para obtencão do Grau de Mestre em Engenharia Civil - Perfil Estruturas O comportamento de uma estrutura sujeita a cargas dinâmicas depende de características como a massa, a rigidez dos vários elementos e da capacidade de dissipação de energia. A resposta dinâmica da estrutura apoiada num solo depende das propriedades dinâmicas dos dois sistemas. A resposta do sistema é influenciada pelos efeitos de interacção solo-estrutura. Nesta dissertação estudou-se um m...

  10. Corrosion fatigue crack growth in clad low-alloy steels: Part 1, medium-sulfur forging steel

    International Nuclear Information System (INIS)

    James, L.A.; Poskie, T.J.; Auten, T.A.; Cullen, W.H.

    1996-01-01

    Corrosion fatigue crack propagation tests were conducted on a medium- sulfur ASTM A508-2 forging steel overlaid with weld-deposited Alloy EN82H cladding. The specimens featured semi-elliptical surface cracks penetrating approximately 6.3 mm of cladding into the underlying steel. The initial crack sizes were relatively large with surface lengths of 30.3--38.3 mm, and depths of 13.1--16.8 mm. The experiments were conducted in a quasi-stagnant low-oxygen (O 2 < 10 ppb) aqueous environment at 243 degrees C, under loading conditions (ΔK, R, and cyclic frequency) conductive to environmentally-assisted cracking (EAC) in higher-sulfur steels under quasi-stagnant conditions. Earlier experiments on unclad compact tension specimens of this heat of steel did not exhibit EAC, and the present experiments on semi-elliptical surface cracks penetrating cladding also did not exhibit EAC

  11. Una solución dinámica para juegos con utilidades transferibles

    Directory of Open Access Journals (Sweden)

    Juan Carlos Cesco

    2008-01-01

    Full Text Available En este trabajo definimos un tipo de solución dinámica para juegos con utilidades transferibles. La solución dinámica fue introducida por Shenoy (1980 en el marco de juegos abstractos como un medio para describir algunos procesos de negociación. En el contexto de los juegos con utilidades transferibles estudiamos su comportamiento tanto en la clase de los juegos equilibrados (con Core no vacío como en el de los juegos no equilibrados. En esta última subclase mostramos que la solución dinámica debe contener los elementos de ciertos ciclos de preimputaciones denominados ciclos maximales. Estos ciclos aparecen en relación con un esquema dinámico elaborado originalmente para aproximar puntos en el Core de un juego. En la subclase de los juegos equilibrados, la solución dinámica coincide con el Core, lo que establece un enfoque unificado de solución. El problema de existencia de ciclos maximales no está completamente resuelto, pero en algunas subclases de juegos podemos exhibir teoremas de existencia y una descripción completa de la solución dinámica.

  12. Effects of sodium environment on the mechanical properties of Fe-2 1/4Cr-1Mo steel

    International Nuclear Information System (INIS)

    Chopra, O.K.

    1983-09-01

    Mechanical property data on isothermally annealed, thermally aged, and sodium-exposed Fe-2 1/4Cr-1Mo steel are analyzed to evaluate the influence of the sodium environment as well as the effects of the microstructural and compositional changes that occur in the steel during long-term exposure to sodium. Correlations are developed to predict the environmental effects on tensile, creep, fatigue, and creep-fatigue properties of Fe-2 1/4Cr-1Mo steel in sodium. The results indicate that at temperatures 0 C), degradation of mechanical properties is essentially due to thermal aging. Loss of carbon from the steel reduces both the tensile and creep-rupture strength, but has little or no effect on the fatigue properties. The cyclic properties of Fe-2 1/4Cr-1Mo steel in sodium are superior to those in air. The creep-fatigue behavior in sodium is significantly different from that in an air environment. The creep-fatigue data are analyzed using the interactive damage rate equations to predict the time-dependent fatigue behavior of isothermally annealed Fe-2 1/4Cr-1Mo steel in sodium. 15 references, 7 figures, 1 table

  13. microstructure change in 12 % Cr steel during creep

    International Nuclear Information System (INIS)

    Winatapura, D. S.; Panjaitan, E.; Arslan, A.; Sulistioso, G.S.

    1998-01-01

    The microstructure change in steel containing of 12% Cr or DIN X20CrMoV 12 1 during creep has been studied by means of optical microscopy and Transmission Electron Microscope (TEM). The creep testing at 650 o C was conducted under constant load of 650 Mpa. The heat treatment of the specimen before creep testing was austenization, followed by tempering for 2 hours. The obtained microstructure was tempered martensitic. This microstructure consisted of the martensite laths, and distributed randomly in the matrix. During tempering, chromium carbide particles of Cr 7 C 6 less than 0,2 μmin-size were precipitated on or and in the subgrain and lath martensite grain boundary. During creep testing those particles transformed and precipitated as chrome carbide precipitates of Cr 23 C 6 . At the secondary creep stage, the void formation occurred, and then it developed into the creep cracks. At tertiary creep stage for 3554 hours, the specimen was failure. The creep cracks were informs of transgranular and intergranular modes which propagated almost perpendicular to the stress axis. From this observation, it is suggested that tempering caused the ductility of martensitic microstructure, which increased the creep resistant or Cr 12% steel

  14. Steel pipelines standards for fittings and joint accessories

    CERN Document Server

    DIN

    2013-01-01

    Die 1. Auflage von DIN Handbook 15/6 erweitert die DIN Handbook-Reihe um den Themenbereich Fittings für verschiedene Montagetechniken. Es enthält in englischer Übersetzung die wesentlichen Normen über Lötfittings aus Kupfer, Temperguss-Fittings, Fittings aus Stahl und Kunststofffittings. Abgerundet wird der Inhalt durch ergänzende Normen, Begriffe und Grundnormen. Reihe DIN_Handbook - 15/6

  15. Effects of sodium environment on the mechanical properties of Fe-2 1/4Cr-1Mo steel

    International Nuclear Information System (INIS)

    Chopra, O.K.

    Mechanical property data on isothermally annealed, thermally aged, and sodium-exposed Fe-2 1/4Cr-1Mo steel are analyzed to evaluate the influence of the sodium environment as well as the effects of the microstructural and compositional changes that occur in the steel during long-term exposure to sodium. Correlations are developed to predict the environmental effects on tensile, creep, fatigue, and creep-fatigue properties of Fe-2 1/4Cr-1Mo steel in sodium. The results indicate that at temperatures <823 K (550 deg. C), degradation of mechanical properties is essentially due to thermal aging. Loss of carbon from the steel reduces both the tensile and creep-rupture strength, but has little or no effect on the fatigue properties. The cyclic properties of Fe-2 1/4Cr-1Mo steel in sodium are superior to those in air. The creep-fatigue behaviour in sodium is significantly different from that in an air environment. The creep-fatigue data are analyzed using the interactive damage rate equations to predict the time-dependent fatigue bahaviour of isothermally annealed Fe-2 1/4Cr-1Mo steel in sodium. (author)

  16. Radiographic sensitivity evaluated by IQI DIN in double wall radiography and simple view

    International Nuclear Information System (INIS)

    Oliveira, C.S. de; Santos Filho, M. dos

    1983-01-01

    A comparison between the sensitivity of IQI-DIN put at the film side with the sensitivity of the IQI-DIN put at the source side, only for the double wall-simple view technique (DW-SW) is presented. An analysis about the requirements of radiographyic sensitivity in accordance to DIN rule is done. (E.G.) [pt

  17. A ΔdinB mutation that sensitizes Escherichia coli to the lethal effects of UV- and X-radiation

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Mei-Chong W.; Franco, Magdalena; Vargas, Doris M. [Department of Biological Sciences, San Jose State University, San Jose, CA 95192 (United States); Hudman, Deborah A. [Department of Microbiology and Immunology, A.T. Still University, Kirksville College of Osteopathic Medicine, Kirksville, MO 63501 (United States); White, Steven J. [Department of Biological Sciences, San Jose State University, San Jose, CA 95192 (United States); Fowler, Robert G., E-mail: rfowler@sjsu.edu [Department of Biological Sciences, San Jose State University, San Jose, CA 95192 (United States); Sargentini, Neil J. [Department of Microbiology and Immunology, A.T. Still University, Kirksville College of Osteopathic Medicine, Kirksville, MO 63501 (United States)

    2014-05-15

    Highlights: • We describe Δ(dinB-yafN)883(::kan), a novel dinB allele, referred to as ΔdinB883, a deletion that sensitizes E. coli cells to UV irradiation. • This UV radiation sensitivity is most acute in the early logarithmic phase of culture growth. • This UV radiation sensitivity is completely dependent upon a functional umuDC operon. • Sequencing reveals ΔdinB883 retains the proximal 161 nucleotides, i.e., 54 amino acids, of the wild-type sequence. • The ΔdinB883 mutant is hypothesized to produce a peptide of 83 amino acids, DinB883, that compromises UmuDC function. - Abstract: The DinB (PolIV) protein of Escherichia coli participates in several cellular functions. We investigated a dinB mutation, Δ(dinB-yafN)883(::kan) [referred to as ΔdinB883], which strongly sensitized E. coli cells to both UV- and X-radiation killing. Earlier reports indicated dinB mutations had no obvious effect on UV radiation sensitivity which we confirmed by showing that normal UV radiation sensitivity is conferred by the ΔdinB749 allele. Compared to a wild-type strain, the ΔdinB883 mutant was most sensitive (160-fold) in early to mid-logarithmic growth phase and much less sensitive (twofold) in late log or stationary phases, thus showing a growth phase-dependence for UV radiation sensitivity. This sensitizing effect of ΔdinB883 is assumed to be completely dependent upon the presence of UmuDC protein; since the ΔdinB883 mutation did not sensitize the ΔumuDC strain to UV radiation killing throughout log phase and early stationary phase growth. The DNA damage checkpoint activity of UmuDC was clearly affected by ΔdinB883 as shown by testing a umuC104 ΔdinB883 double-mutant. The sensitivities of the ΔumuDC strain and the ΔdinB883 ΔumuDC double-mutant strain were significantly greater than for the ΔdinB883 strain, suggesting that the ΔdinB883 allele only partially suppresses UmuDC activity. The ΔdinB883 mutation partially sensitized (fivefold) uvrA and uvr

  18. Evaluation of the Effect of Different Plasma-Nitriding Parameters on the Properties of Low-Alloy Steel

    Science.gov (United States)

    Zdravecká, Eva; Slota, Ján; Solfronk, Pavel; Kolnerová, Michaela

    2017-07-01

    This work is concerned with the surface treatment (ion nitriding) of different plasma-nitriding parameters on the characteristics of DIN 1.8519 low-alloy steel. The samples were nitrided from 500 to 570 °C for 5-40 h using a constant 25% N2-75% H2 gaseous mixture. Lower temperature (500-520 °C) favors the formation of compound layers of γ' and ɛ iron nitrides in the surface layers, whereas a monophase γ'-Fe4 N layer can be obtained at a higher temperature. The hardness of this layer can be obtained when nitriding is performed at a higher temperature, and the hardness decreases when the temperature increases to 570 °C. These results indicate that pulsed plasma nitriding is highly efficient at 550 °C and can form thick and hard nitrided layers with satisfactory mechanical properties. The results show the optimized nitriding process at 540 °C for 20 h. This process can be an interesting means of enhancing the surface hardness of tool steels to forge dies compared to stamped steels with zinc coating with a reduced coefficient of friction and improving the anti-sticking properties of the tool surface.

  19. Simulación de la fluencia en caliente de un acero microaleado con un contenido medio de carbono. II parte. Recristalización dinámica: inicio y cinética

    Directory of Open Access Journals (Sweden)

    Cabrera, J. M.

    1997-06-01

    Full Text Available According to the part 1 of this work, in this second part the dynamic recrystallization of a commercial medium carbon microalloyed steel is characterized from the point of view of its onset and kinetics. For this purpose uniaxial hot compression tests were carried out over a range of five orders of magnitude in strain rate and 300 °C of temperature. Experimental results are compared with those reported in the literature and the possible effect of dynamic precipitation is also analyzed. It is verified that the kinetics of dynamic recrystallization can faithfully be described by the classical Avrami equation.

    Siguiendo el planteamiento efectuado en la I parte de este trabajo, en esta II parte se caracteriza la recristalización dinámica de un acero comercial microaleado con un contenido medio de carbono desde el punto de vista de su inicio y de su cinética. Con este objeto se efectuaron ensayos de compresión uniaxial en caliente en un intervalo de cinco órdenes de magnitud en velocidad de deformación y 300 °C de temperatura. Los resultados experimentales se comparan con los resultados reportados por diversos autores y se analizan los posibles efectos de precipitación dinámica. Se verifica que la cinética de la recristalización dinámica puede representarse fielmente por la ecuación de Avrami.

  20. Effects of different N sources on riverine DIN export and retention in a subtropical high-standing island, Taiwan

    Science.gov (United States)

    Huang-Chuan, Jr.; Lee, Tsung-Yu; Lin, Teng-Chiu; Hein, Thomas; Lee, Li-Chin; Shih, Yu-Ting; Kao, Shuh-Ji; Shiah, Fuh-Kwo; Lin, Neng-Huei

    2016-03-01

    Increases in nitrogen (N) availability and mobility resulting from anthropogenic activities have substantially altered the N cycle, both locally and globally. Taiwan characterized by the subtropical montane landscape with abundant rainfall, downwind of the most rapidly industrializing eastern coast of China, can be a demonstration site for extremely high N input and riverine DIN (dissolved inorganic N) export. We used 49 watersheds with similar climatic and landscape settings but classified into low, moderate, and highly disturbed categories based on population density to illustrate their differences in nitrogen inputs (through atmospheric N deposition, synthetic fertilizers, and human emission) and DIN export ratios. Our results showed that the island-wide average riverine DIN export is ˜ 3800 kg N km-2 yr-1, approximately 18 times the global average. The average riverine DIN export ratios are 0.30-0.51, which are much higher than the averages of 0.20-0.25 of large rivers around the world, indicating excessive N input relative to ecosystem demand or retention capacity. The low disturbed watersheds have a high N retention capacity and DIN export ratios of 0.06-0.18 in spite of the high N input (˜ 4900 kg N km-2 yr-1). The high retention capacity is likely due to effective uptake by secondary forests in the watersheds. The moderately disturbed watersheds show a linear increase in DIN export with increases in total N inputs and mean DIN export ratios of 0.20 to 0.31. The main difference in land use between low and moderately disturbed watersheds is the greater proportion of agricultural land cover in the moderately disturbed watersheds. Thus, their greater DIN export could be attributed to N fertilizers used in the agricultural lands. The greater export ratios also imply that agricultural lands have a lower proportional N retention capacity and that reforestation could be an effective land management practice to reduce riverine DIN export. The export ratios of the

  1. Multiple pathways for SOS-induced mutagenesis in Escherichia coli: An overexpression of dinB/dinP results in strongly enhancing mutagenesis in the absence of any exogenous treatment to damage DNA

    Science.gov (United States)

    Kim, Su-Ryang; Maenhaut-Michel, Geneviéve; Yamada, Masami; Yamamoto, Yoshihiro; Matsui, Keiko; Sofuni, Toshio; Nohmi, Takehiko; Ohmori, Haruo

    1997-01-01

    dinP is an Escherichia coli gene recently identified at 5.5 min of the genetic map, whose product shows a similarity in amino acid sequence to the E. coli UmuC protein involved in DNA damage-induced mutagenesis. In this paper we show that the gene is identical to dinB, an SOS gene previously localized near the lac locus at 8 min, the function of which was shown to be required for mutagenesis of nonirradiated λ phage infecting UV-preirradiated bacterial cells (termed λUTM for λ untargeted mutagenesis). A newly constructed dinP null mutant exhibited the same defect for λUTM as observed previously with a dinB::Mu mutant, and the defect was complemented by plasmids carrying dinP as the only intact bacterial gene. Furthermore, merely increasing the dinP gene expression, without UV irradiation or any other DNA-damaging treatment, resulted in a strong enhancement of mutagenesis in F′lac plasmids; at most, 800-fold increase in the G6-to-G5 change. The enhanced mutagenesis did not depend on recA, uvrA, or umuDC. Thus, our results establish that E. coli has at least two distinct pathways for SOS-induced mutagenesis: one dependent on umuDC and the other on dinB/P. PMID:9391106

  2. COMPONENŢA AMINOACIZILOR DIN BIOMASA ALGEI CIANOFITE NOSTOC GELATINOSUM (SCHOUSB ELENK.

    Directory of Open Access Journals (Sweden)

    Sergiu DOBROJAN

    2016-02-01

    Full Text Available În articol este analizată componenţa aminoacizilor din biomasa algei cianofite Nostoc gelatinosum (Schousb Elenk. colectate de pe mediul nutritiv Drew. Din grupa aminoacizilor esenţiali în biomasa algei Nostoc gelatinosum (Schousb Elenk. se conţine în cantităţi majore leucina (2,142±0,06 mg/100 mg, treonina (1,188±0,02 mg/100 mg şi valina (1,085±0,03 mg/100 mg. Din aminoacizii neesenţiali predomină acidul aspartic (4,523±0,11 mg/100 mg şi acidul glutamic (2,774±0,07 mg/100 mg. Alga Nostoc gelatinosum (Schousb Elenk. are un conţinut bogat de aminoacizi şi poate servi ca sursă pentru vaste domenii de aplicare.THE AMINO ACIDS COMPOSITION OF THE BLUE-GREEN ALGANOSTOC GELATINOSUM (SCHOUSB ELENKThis article presents the amino acid content of the blue-green alga Nostoc gelatinosum (Schousb Elenk. collected from the Drew nutritive medium. From the essential amino group in Nostoc gelatinosum (Schousb Elenk. biomass, major amounts are contained leucine (2,142 ± 0,06 mg/100 mg, threonine (1,188 ± 0,02 mg/100 mg and valine (1,085 ± 0,03 mg/100 mg. From nonessential amino acids predominates aspartic acid (4,523 ± 0,11 mg/100 mg and glutamic acid (2,774 ± 0.07 mg/100 mg. The alga Nostoc gelatinosum (Schousb Elenk. has a high content of amino acids and can serve as a source for vast areas of application. 

  3. Protection of proprietary rights of DIN standards in connection with statutory and administrative provisions

    International Nuclear Information System (INIS)

    Katzenberger, P.

    1985-01-01

    On the basis of contracts entered with the German Institute of Standardization (DIN), the state bodies and authorities tend to refer to Din standards in many ways when issuing statutory or administrative provisions. Some Din standards are also printed in official publications- with or without Din's prior consent. Such common practice leads to the question whether the Din standards which on pinciple meet the general requirements made on the protection of proprietary rights are losing this protection by the fact that official publications are exempt from the protection of proprietary rights (Art.5 UrhG). The author points out that the thorough analysis of the legal position in terms of interests, proprietary rights and constitution indicated that this is not, in principle, the case. (orig.) [de

  4. Toughness of 2,25Cr-1Mo steel and weld metal

    Science.gov (United States)

    Acarer, Mustafa; Arici, Gökhan; Acar, Filiz Kumdali; Keskinkilic, Selcuk; Kabakci, Fikret

    2017-09-01

    2,25Cr-1Mo steel is extensively used at elevated temperature structural applications in fossil fire power plants for steam pipes, nozzle chambers and petrochemical industry for hydrocracking unit due to its excellent creep resistance and good redundant to oxidation. Also they should have acceptable weldability and toughness. The steels are supplied in quenched and tempered condition and their welded components are subjected to post-weld heat treatment (PWHT). Tempering process is carried out at 690-710°C to improve toughness properties. However they are sensitive to reheat cracking and temper embrittlement. To measure temper embrittlement of the steels and their weld metal, temper embrittlement factor and formula (J factor - Watanabe and X formula- Bruscato) are used. Step cooling heat treatment is also applied to determine temper embrittlement. In this study, toughness properties of Cr Mo (W) steels were reviewed. Also transition temperature curves of 2,25Cr-1Mo steel and its weld metal were constructed before and after step cool heat treatment as experimental study. While 2,25Cr-1Mo steel as base metal was supplied, all weld metal samples were produced in Gedik Welding Company. Hardness measurements and microstructure evaluation were also carried out.

  5. The KNK II/1 fuel assembly NY-205: Compilation of the irradiation history and the fuel and fuel pin fabrication data of the INTERATOM data bank system BESEX

    International Nuclear Information System (INIS)

    Patzer, G.; Geier, F.

    1988-01-01

    The fuel assembly NY-205 has been irradiated during the first and the second core of KNK II with a total residence time of 832 equivalent full-power days. A maximum burnup of 175.000 MWd/tHM or 18.6 % was reached with a maximum steel damage of 66 dpa-NRT. For the cladding the materials 1.4970 and 1.4981 have been used in different metallurgical conditions, and for the Uranium/Plutonium mixed- oxide fuel the most important variants of the major fabrication parameters had been realized. The assembly will be brought to the Hot Cells of the KfK Karlsruhe for post-irradiation examination in February 1988, so that the knowledge of the fabrication data is of interest for the selection of fuel pins and for the evaluation of the examination results. Therefore this report compiles the fuel and fuel pin fabrication data from the INTERATOM data bank system BESEX and additionally, an overview of the irradiation history of the assembly is given [de

  6. Hydrogen gas embrittlement of stainless steels mainly austenitic steels. Volumes 1 and 2

    International Nuclear Information System (INIS)

    Azou, P.

    1988-01-01

    Steel behavior in regard to hydrogen is examined especially austenitic steels. Gamma steels are studied particularly the series 300 with various stabilities and gamma steels with improved elasticity limit for intermetallic phase precipitation and nitrogen additions. A two-phase structure γ + α' is also studied. All the samples are tested for mechanical behavior in gaseous hydrogen. Influence of metallurgical effects and of testing conditions on hydrogen embrittlement are evidenced. Microstructure resulting from mechanical or heat treatments, dislocation motion during plastic deformation and influence of deformation rate are studied in detail [fr

  7. Physical metallurgy of laser surface melted plastic mould steels: a case study

    Directory of Open Access Journals (Sweden)

    Colaço, R.

    1998-04-01

    Full Text Available The purpose of this paper is to illustrate the potential of laser surface melting to improve the surface characteristics of plastic mould steels, using a typical plastic mould steel (DIN X43Cr12 as a case study. After laser surface melting the microstructure of this steel is formed by fine dendrites of austenite partially transformed into martensite. Although the equilibrium solidification phase is 8- ferrite, the formation of primary austenite is kinetically favored and this phase tends to predominate at the high solidification speeds used in laser processing. It was observed that the volume fraction of retained austenite depends critically on the laser processing parameters, so that the microstructure can change from almost completely martensitic to almost completely austenitic by changing the laser processing parameters. Laser melted tool steels show remarkable secondary hardening after tempering at suitable temperatures. In DIN X42Cr13 the secondary hardening peak temperature after LSM (600°C is 100°C higher than after conventional heat treatment (500°C, due to the presence of large amounts of retained austenite. It was observed that this phase only destabilizes above 600°C, due to the precipitation of M7C3 and stress relieving. After destabilization, retained austenite transforms into martensite during cooling. Secondary hardening is due to the transformation of retained austenite into martensite and to the precipitation of M7C3 and M23C6 carbides.

    El objetivo del presente trabajo es ilustrar el potencial de la fusión superficial mediante láser para la mejora de las características estructurales de los moldes de acero para plásticos, centrándolo en el caso concreto del acero DIN X42Cr13. Tras el tratamiento de fusión superficial mediante láser, la microestructura del material está formada por dendritas finas de austenita parcialmente transformadas en

  8. CONŢINUTUL METALELOR GRELE ÎN COMPONENTELE MEDIULUI DIN ZONA DE CENTRU A REPUBLICII MOLDOVA

    Directory of Open Access Journals (Sweden)

    Olesea GLIGA

    2016-02-01

    Full Text Available Scopul acestei lucrări rezidă în determinarea conţinutului unor metale grele (Pb, Cd şi Cu în componentele mediu­lui (sol, apă şi floră din zona de centru a Republicii Moldova. Au fost selectate 4 situri de studiu, cu diferit impact antropic, din care au fost prelevate probe de sol, apă şi floră. Conţinutul de metale grele în componentele de mediu au fost deter­minate prin Spectrometria de Absorbţie Atomică cu atomizare termică. Rezultatele cercetărilor au demonstrat prezenţa metalelor cercetate în toate probele de sol şi floră analizate şi lipsa acestora în probele de apă, cu excepţia Cu. Concen­tra­ţiile de Pb, Cd şi Cu în solurile din siturile antropizate (industrial şi transport auto au fost mai mari în comparaţie cu cele din situl forestier (td = 2,05 - 4,36; P < 0,05 - 0,001. Analogic celor din sol, şi concentraţiile acestora în flora meliferă pre­levată din siturile antropizate au înregistrat valori mai mari în comparaţie cu cel forestier (td = 1,19 - 4,0; P > 0,1 - <0,001. De asemenea, şi concentraţia de Cu în mostrele de apă prelevate din siturile industrial şi transport auto a fost mai mare în comparaţie cu cele din situl forestier (td = 2,0 - 5,17; P < 0,1- 0,001. Putem constata că concentraţia metalelor grele cercetate în componentele mediului este în funcţie de prezenţa surselor de poluare din aceste situri. Totodată, în toate siturile cercetate nu au fost constatate depăşiri ale nivelurilor maximal admisibile, conform normelor în vigoare. THE CONTENT OF HEAVY METALS IN THE ENVIRONMENTAL COMPONENTS IN THE CENTRAL AREA OF THE REPUBLIC OF MOLDOVA The aim of this paper was to determine the content of heavy metals (Pb, Cd and Cu in the environmental components (soil, water and flora in the central area of the Republicof Moldova. Have been selected 4 study sites with different human impact, from which have been collected samples of soil, water and flora. The heavy metal

  9. Analisis Kecenderungan Manhaj Akidah Shaykh Shams al-Din al-Sumatera’i

    Directory of Open Access Journals (Sweden)

    MOHD HAIDHAR KAMARZAMAN

    2016-12-01

    Full Text Available Shaykh Shams al-Din al-Sumatera'i is a very great and respected scholar during 16th and 17th century of Acheh. His knowledge in various fields recognized by local and international scholars. He had been a Qadi Malik al-’Adil, a religious leader, who became a referred by communities and country during the reign of the three Sultans of Aceh. He has authored nearly 40 pieces of books related to the theology and sufism. This study focuses on the methods used by Shaykh Shams al-Din al-Sumatera'i in his theological writings. This study found that Shaykh Shams al-Din al-Sumatera'i had used six methods in the such writings.

  10. Review of time-dependent fatigue behavior and life prediction for 2 1/4 Cr-1 Mo steel

    International Nuclear Information System (INIS)

    Booker, M.K.; Majumdar, S.

    1982-01-01

    Available data on creep-fatigue life and fracture behavior of 2 1/4 Cr-1 Mo steel are reviewed. Whereas creep-fatigue interaction is important for Type 304 stainless steel, oxidation effects appear to dominate the time-dependent fatigue behavior of 2 1/4 Cr-1 Mo steel. Four of the currently available predictive methods - the Linear Damage Rule, Frequency Separation Equation, Strain Range Partitioning Equation, and Damage Rate Equation - are evaluated for their predictive capability. Variations in the parameters for the various predictive methods with temperature, heat of material, heat treatment, and environment are investigated. Relative trends in the lives predicted by the various methods as functions of test duration, waveshape, etc., are discussed. The predictive methods will need modification in order to account for oxidation and aging effects in the 2 1/4 Cr-1 Mo steel. Future tests that will emphasize the difference between the various predictive methods are proposed

  11. Design of joints in steel and composite structures Eurocode 3 : design of steel structures : part 1-8 : design of joints, Eurocode 4 : design of composite steel and concrete structures : part 1-1 : general rules and rules for buildings

    CERN Document Server

    Jaspart, Jean-Pierre

    2016-01-01

    This book details the basic concepts and the design rules included in Eurocode 3 Design of steel structures Part 1-8 Design of joints. Joints in composite construction are also addressed through references to Eurocode 4 Design of composite steel and concrete structures Part 1-1 General rules and rules for buildings. Attention has to be duly paid to the joints when designing a steel or composite structure, in terms of the global safety of the construction, and also in terms of the overall cost, including fabrication, transportation and erection. Therefore, in this book, the design of the joints themselves is widely detailed, and aspects of selection of joint configuration and integration of the joints into the analysis and the design process of the whole construction are also fully covered. Connections using mechanical fasteners, welded connections, simple joints, moment-resisting joints and lattice girder joints are considered. Various joint configurations are treated, including beam-to-column, beam-to-beam, ...

  12. Induction surface hardening of hard coated steels

    Energy Technology Data Exchange (ETDEWEB)

    Pantleon, K.; Kessler, O.; Hoffann, F.; Mayr, P. [Stiftung Inst. fuer Werkstofftechnik, Bremen (Germany)

    1999-11-01

    The properties of hard coatings deposited using CVD processes are usually excellent. However, high deposition temperatures negatively influence the substrate properties, especially in the case of low alloyed steels. Therefore, a subsequent heat treatment is necessary to restore the properties of steel substrates. Here, induction surface hardening is used as a method of heat treatment after the deposition of TiN hard coatings on AISI 4140 (DIN42CrMo4) substrates. The influences of the heat treatment on both the coating and the substrate properties are discussed in relation to the parameters of induction heating. Thereby, the heating time, heating atmosphere and the power input into the coating-substrate compounds are varied. As a result of induction surface hardening, the properties of the substrates are improved without losing good coating properties. High hardness values in the substrate near the interface allow the AISI 4140 substrates to support TiN hard coatings very well. Consequently, higher critical loads are measured in scratch tests after the heat treatment. Also, compressive residual stresses in the substrate are generated. In addition, only a very low distortion appears. (orig.)

  13. Creep-fatigue behavior of 2 1/4Cr-1Mo steel at 5500C in air and vacuum

    International Nuclear Information System (INIS)

    Asayama, T.; Cheng, S.Z.; Asada, Y.; Mitsuhashi, S.; Tachibana, Y.

    1987-01-01

    Following studies on creep-fatigue behaviors of 304 steel at 650 0 C (Asada et al (1980) and Morishita et al (1984), (1985), (1987)), 2 1/4Cr-1Mo steel was studied on its creep-fatigue behaviors at 550 0 C in air and vacuum of 100 and 0.1 μPa. The present study intends to give a base for an evaluation of the environmental effect through obtaining a pure creep-fatigue behavior of this steel which is free from the environmental effect. In the previous studies on 304 steel, tests were conducted in three kinds of environment of air, 100 and 0.1 μPa vacuum. It seemed to be plausible that the 0.1 μPa vacuum shows the pure creep-fatigue behavior of 304 steel at 650 0 C which is almost completely free from the environment. A creep-fatigue life in 0.1 μPa vacuum is almost one order of magnitude higher than that in air. The 100 μPa vacuum suggested that the environmental effect of air still remains but is so small that a creep-fatigue life in 100 μPa is same to that in 0.1 μPa in some strain wave forms. The present study intends to examine if similar observations are obtained with 2 1/4Cr-1Mo steel at 550 0 C. This paper describes the analysis of the overstress and damages, in addition to a creep-fatigue result. (orig.GL)

  14. Effect of Co deposition on oxidation behavior and electrical properties of ferritic steel for solid oxide fuel cell interconnects

    Energy Technology Data Exchange (ETDEWEB)

    Kruk, A.; Adamczyk, A.; Gil, A. [AGH University of Science and Technology, Faculty of Materials Science and Ceramics, al. Mickiewicza 30, 30-059 Krakow (Poland); Kąc, S. [AGH University of Science and Technology, Faculty of Metals Engineering and Industrial Computer Science, al. Mickiewicza 30, 30-059 Krakow (Poland); Dąbek, J.; Ziąbka, M. [AGH University of Science and Technology, Faculty of Materials Science and Ceramics, al. Mickiewicza 30, 30-059 Krakow (Poland); Brylewski, T., E-mail: brylew@agh.edu.pl [AGH University of Science and Technology, Faculty of Materials Science and Ceramics, al. Mickiewicza 30, 30-059 Krakow (Poland)

    2015-09-01

    In this work, a Co layer deposited on DIN 50049 steel by means of pulsed laser deposition was applied for the protection of solid oxide fuel cell (SOFC) interconnects operating on the cathode side. The coated and uncoated steel samples were oxidized in air at 1073 K for 500 h, and their microstructures as well as electrical resistances were evaluated using X-ray diffraction, atomic force microscopy, scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy, and the 2-probe 4-point direct current method. It was demonstrated that the Co coating had reduced the oxidation rate of the steel by nearly a half. The area-specific resistance value of the coated steel was 5 × 10{sup −6} Ω·m{sup 2}, which was significantly lower than that of bare steel after 350 h of oxidation at 1073 K. Cr vaporization tests showed that the Co coating was efficient at blocking the outward diffusion of Cr. The obtained results prove that steel coated with a thin film of cobalt was suitable for use as metallic interconnect material in SOFCs operating at intermediate temperatures. - Highlights: • Co layer was deposited on ferritic steel by means of pulsed laser deposition. • Coated and bare ferritic steel samples were exposed to air at 1073 K for 500 h. • Scale growth rate on bare steel is higher than that on coated steel. • Electrical resistance for oxidized coated steel was lower than for bare steel. • Co-coated steel effectively reduced the formation of volatile Cr species.

  15. IMUNOREACTIVITATEA ÎNCRUCIŞATĂ POTENŢIALĂ A GLOBULINELOR DE REZERVĂ DIN SEMINŢE

    Directory of Open Access Journals (Sweden)

    Ala CHERDIVARĂ

    2018-03-01

    Full Text Available Globulinele de rezervă 7S şi 11S din seminţele de arahide şi de soia, ca ingrediente naturale ale alimentelor, pot determina dezvoltarea reacţiei alergice cauzate de formarea intensivă a imunoglobulinelor E (IgE alergen specifice. Secvenţele de aminoacizi ale globulinelor de rezervă din seminţe sunt conservative; prin urmare, în secvenţele multora dintre ele există situsuri care sunt similare în structura primară a epitopilor IgE, ceea ce determină alergenicitatea glo­bu­linelor 7S şi 11S din arahide şi soia. În prezentul studiu a fost efectuată o evaluare cantitativă a probabilităţii prezenţei epitopilor IgE, care determină imunoreactivitatea încrucişată stabilită a globulinelor de rezervă din arahide şi din soia în globulinele 7S şi 11S din seminţele altor plante.A fost efectuată o estimare cantitativă a probabilității prezenței epitopilor IgE ce determină imunoreactivitatea încrucișată stabilită a globulinelor de rezervă din arahide și soia în secvențele de aminoacizi ale globulinelor 7S și 11S din semințele altor plante.POTENTIAL CROSS IMMUNOREACTIVITY OF SEED STORAGE GLOBULINSSeed storage 7S and 11S globulins of peanut and soybean as natural components of food can lead to the development of increased allergic sensitivity caused by the intensive formation of allergen-specific immunoglobulin E (IgE. The amino acid sequences of the seed storage globulins are conservative, therefore, in the sequences of many of them there are sites that are close similar of IgE epitopes of 7S and 11S globulins of peanuts and soybeans.In the present work, a quantitative assessment of the probability of the presence of IgE epitopes determining the established cross immunoreactivity of seed storage globulins of peanuts and soybeans, in the sequences of 7S and 11S seed storage globulins of other plants was carried out.

  16. Planificación de trayectorias para un robot tipo con restricciones dinámicas

    Directory of Open Access Journals (Sweden)

    Leonardo Solaque Guzmán

    2008-01-01

    Full Text Available Este documento presenta una aproximación a la planificación de caminos óptimos para un sistema con restricciones dinámicas y desplazándose dentro de un espacio libre de obstáculos. Se considera el modelo dinámico del dirigible y un análisis para el planteamiento de modelos simplificados o comúnmente conocidos como modelos de control. Se propone una planificación de la trayectoria desde el punto de vista de la teoría óptima utilizando un modelo de la dinámica de un robot móvil (que se desplaza a velocidad constante y en avance, es decir con restricciones dinámicas como punto de partida para la primera aproximación a los caminos óptimos. Para el suavizado de las trayectorias del dirigible se proponen dos modelos con relajación en la dinámica de la variable de control y finalmente se presenta una simulación de la comparación de los diferentes resultados.

  17. Mycobacterium tuberculosis DinG is a structure-specific helicase that unwinds G4 DNA: implications for targeting G4 DNA as a novel therapeutic approach.

    Science.gov (United States)

    Thakur, Roshan Singh; Desingu, Ambika; Basavaraju, Shivakumar; Subramanya, Shreelakshmi; Rao, Desirazu N; Nagaraju, Ganesh

    2014-09-05

    The significance of G-quadruplexes and the helicases that resolve G4 structures in prokaryotes is poorly understood. The Mycobacterium tuberculosis genome is GC-rich and contains >10,000 sequences that have the potential to form G4 structures. In Escherichia coli, RecQ helicase unwinds G4 structures. However, RecQ is absent in M. tuberculosis, and the helicase that participates in G4 resolution in M. tuberculosis is obscure. Here, we show that M. tuberculosis DinG (MtDinG) exhibits high affinity for ssDNA and ssDNA translocation with a 5' → 3' polarity. Interestingly, MtDinG unwinds overhangs, flap structures, and forked duplexes but fails to unwind linear duplex DNA. Our data with DNase I footprinting provide mechanistic insights and suggest that MtDinG is a 5' → 3' polarity helicase. Notably, in contrast to E. coli DinG, MtDinG catalyzes unwinding of replication fork and Holliday junction structures. Strikingly, we find that MtDinG resolves intermolecular G4 structures. These data suggest that MtDinG is a multifunctional structure-specific helicase that unwinds model structures of DNA replication, repair, and recombination as well as G4 structures. We finally demonstrate that promoter sequences of M. tuberculosis PE_PGRS2, mce1R, and moeB1 genes contain G4 structures, implying that G4 structures may regulate gene expression in M. tuberculosis. We discuss these data and implicate targeting G4 structures and DinG helicase in M. tuberculosis could be a novel therapeutic strategy for culminating the infection with this pathogen. © 2014 by The American Society for Biochemistry and Molecular Biology, Inc.

  18. Erosion and deuterium retention of CLF-1 steel exposed to deuterium plasma

    Science.gov (United States)

    Qiao, L.; Wang, P.; Hu, M.; Gao, L.; Jacob, W.; Fu, E. G.; Luo, G. N.

    2017-12-01

    In recent years reduced activation ferritic martensitic steel has been proposed as the plasma-facing material in remote regions of the first wall. This study reports the erosion and deuterium retention behaviours in CLF-1 steel exposed to deuterium (D) plasma in a linear experimental plasma system as function of incident ion energy and fluence. The incident D ion energy ranges from 30 to 180 eV at a flux of 4 × 1021 D m-2 s-1 up to a fluence of 1025 D m-2. SEM images revealed a clear change of the surface morphology as functions of incident fluence and impinging energy. The mass loss results showed a decrease of the total sputtering yield of CLF-1 steel with increasing incident fluence by up to one order of magnitude. The total sputtering yield of CLF-1 steel after 7.2 × 1024 D m-2 deuterium plasma exposure reduced by a factor of 4 compared with that of pure iron, which can be attributed to the enrichment of W at the surface due to preferential sputtering of iron and chromium. After D plasma exposure, the total deuterium retention in CLF-1 steel samples measured by TDS decreased with increasing incident fluence and energy, and a clear saturation tendency as function of incident fluence or energy was also observed.

  19. Welding procedure specification for arc welding of St 52-3N steel plates with covered electrodes

    International Nuclear Information System (INIS)

    Cvetkovski, S.; Slavkov, D.; Magdeski, J.

    2003-01-01

    In this paper the results of approval welding technology for arc welding of plates made of St 52-3N steel are presented. Metal arc welding with covered electrode is used welding process. Test specimens are butt welded in different welding positions P A , P F , P C and P D . Before start welding preliminary welding procedure was prepared. After welding of test specimens non destructive and destructive testing was performed. Obtained results were compared with standard DIN 17100 which concerns to chemical composition and mechanical properties of base material. It was confirmed that in all cases mechanical properties of welded joint are higher than those of base material, so preliminary welding procedure (pWTS) can be accepted as welding procedure specification WPS for metal arc welding of St52-3N steel. (Original)

  20. Temas de Física para Ingeniería: Dinámica del punto material

    OpenAIRE

    Beléndez, Augusto; Pastor Antón, Carlos; Bernabeu, Guillermo

    1988-01-01

    Apuntes de Mecánica: "Dinámica del punto material". Introducción, dinámica del punto. Fuerzas en la naturaleza. Sistemas de referencia. Leyes de Newton. Fuerzas de rozamiento. Ley de la gravitación universal. Aplicación de las leyes de Newton a la resolución de problemas de dinámica. Momento lineal y conservación. Redefinición de fuerza. Momento angular y conservación, fuerzas centrales. Impulso mecánico.

  1. Comparison of low-cycle fatigue data of 2 1/4%CrMo steels

    International Nuclear Information System (INIS)

    Sanderson, S.J.; Petrequin, P.; Nieuwland, H.C.D.

    Data files have been produced on international strain-controlled fatigue information available for 2 1/4%CrMo steels; data assessment from these files is treated in three categories viz: annealed and isothermally annealed 2 1/4%Cr1%Mo steel; normalised and tempered and quenched and tempered 2 1/4%Cr1%Mo steel; and 2 1/4%CrMo variants. The available data have been considered generally in terms of total strain range vs. cycles to failure (Nsub(f)), tensile stress at Nsub(f)/2 vs. cycles to failure and time to failure vs. cycles to failure. Where possible the continuous cycling data have been statistically analysed in terms of the elastic and plastic strain components and cycles to failure to yield best-fit equations over defined temperature (T) regimes viz: T <= 427 deg. C, 427 deg. C < T <= 550 deg. C. and 550 deg. C < T <= 600 deg. C. The behaviour of the steels within the various classifications is discussed. (author)

  2. Gas metal arc weldability of 1.5 GPa grade martensitic steels

    Science.gov (United States)

    Hwang, Insung; Yun, Hyeonsang; Kim, Dongcheol; Kang, Munjin; Kim, Young-Min

    2018-01-01

    The gas metal arc weldability of 1.5 GPa grade martensitic (MART) steel was evaluated using both inverter direct current (DC) and DC pulse power type welders, under conditions of different welding currents, welding speeds, and shielding gasses. By investigating the bead appearance, tensile strength, and arc stability, it was determined that DC pulse power is better than inverter DC power for arc welding of 1.3 mm thick 1.5 GPa grade MART steel. Further, from the results of the weldability for various shielding gases, it was determined that mixed shielding gas is more effective for welding 1.5 GPa grade MART steel than is pure inert gas (Ar) or active (CO2) gas. In the case of pure shielding gas, no sound bead was formed under any conditions. However, when the mixed shielding gas was used, sound and fine beads were obtained.

  3. Susceptibility of 2 1/4 Cr-1Mo steel to liquid metal induced embrittlement by lithium-lead solutions

    International Nuclear Information System (INIS)

    Eberhard, B.A.; Edwards, G.R.

    1984-08-01

    An investigation has been conducted on the liquid metal induced embrittlement susceptibility of 2 1/4Cr-1Mo steel exposed to lithium and 1a/o lead-lithium at temperatures between 190 0 C and 525 0 C. This research was part of an ongoing effort to evaluate the compatibility of liquid lithium solutions with potential fusion reactor containment materials. Of particular interest was the microstructure present in a weld heat-affected zone, a microstructure known to be highly susceptible to corrosive attack by liquid lead-lithium solutions. Embrittlement susceptibility was determined by conducting tension tests on 2 1/4Cr-1Mo steel exposed to an inert environment as well as to a lead-lithium liquid and observing the change in tensile behavior. The 2 1/4Cr-1Mo steel was also given a base plate heat treatment to observe its embrittlement susceptibility to 1a/o lead-lithium. The base plate microstructure was severely embrittled at temperatures less than 500 0 C. Tempering the base plate was effective in restoring adequate ductility to the steel

  4. Herramientas del álgebra lineal para el control de sistemas lineales dinámicos conmutados

    OpenAIRE

    Rivera Martínez, Laura

    2016-01-01

    En el presente proyecto se aborda una introducción a la teoría sobre Sistemas Lineales Dinámicos Conmutados (SLDC), con el propósito de estudiar su comportamiento, que posteriormente (en el Capítulo 5) será aplicada a un problema del ámbito de la ingeniería eléctrica : un circuito RLC. A tal fin, se recurre a la teoría generalizada sobre Sistemas Lineales Dinámicos (SLD), (fundamentada a partir de las referencias [1] y [6], esencialmente) en la cual se desarrolla una explicación detallada ...

  5. Low dose irradiation effects on DIN 1.4948 mechanical properties

    International Nuclear Information System (INIS)

    Schaaf, B. van der; Vries, M.I. de

    For the SNR 300 the licensing authorities require the determination of the lower boundaries of post-irradiation mechanical properties for DIN 1.4948 parent metal and welded joints. It has been established that with decreasing strain rate the post-irradiation tensile ductility decreases. A transition strain rate has been observed, above which there is no effect of irradiation on ductility. The transition strain rate increases with increasing temperature. Coarse grained heats show lower ultimate tensile strength above 800 K than fine grained heats. There is no significant effect of irradiation on load controlled high cycle fatigue with frequencies of 1 Hz or higher. In low cycle fatigue numbers of cycles to failure decrease with decreasing frequency. Increasing the test temperature reduces the number of cycles to failure even more. The frequency effect is more evident at 823 K. Parent metal has a better fatigue resistance than welded joints in unirradiated and irradiated condition. Creep strength is reduced by irradiation due to loss of ductility. It is shown that with increasing grain size the rupture strength decreases. The ductility of welded joints after irradiation is low, in some cases as low as 0.5% creep strain. After irradiation, tensile, creep and fatigue fracture surfaces show many more intergranular features than in the equivalent unirradiated condition. The promotion of intergranular fracture by irradiation and the consequent degradation of low strain rate mechanical properties is explained by the presence of helium on grain boundaries. Several measures to increase the helium content threshold can be taken, such as grain refinement, homogeneous boron distribution and promotion of helium bubble initiation. In cases where helium embrittlement is encountered, life reduction factors on unirradiated material properties must be applied

  6. Dresden 1 Radiation Level Reduction Program. Intergranular corrosion tests of sensitized Type-304 stainless steel in Dow NS-1, and stress corrosion cracking tests of Type-304 stainless steel and carbon and low alloy steels in Dow copper rinse solution

    International Nuclear Information System (INIS)

    Walker, W.L.

    1978-09-01

    Corrosion tests were performed to evaluate the extent of intergranular attack on sensitized Type-304 stainless steel by a proprietary Dow Chemical solvent, NS-1, which is to be used in the chemical cleaning of the Dresden 1 primary system. In addition, tests were performed to evaluate stress corrosion cracking of sensitized Type-304 stainless steel and post-weld heat-treated ASTM A336-F1, A302-B, and A106-B carbon and low alloy steels in a solution to be used to remove residual metallic copper from the Dresden 1 primary system surfaces following the chemical cleaning. No evidence of deleterious corrosion was observed in either set of tests

  7. Effects of different N sources on riverine DIN export and retention in subtropical high-standing island, Taiwan

    Science.gov (United States)

    Huang, J.-C.; Lee, T.-Y.; Lin, T.-C.; Hein, T.; Lee, L.-C.; Shih, Y.-T.; Kao, S.-J.; Shiah, F.-K.; Lin, N.-H.

    2015-10-01

    Increases in nitrogen (N) availability and mobility resulting from anthropogenic activities has substantially altered N cycle both locally and globally. Taiwan characterized by the subtropical montane landscape with abundant rainfall, downwind to the most rapidly industrializing east coast of China can be a demonstration site for extreme high N input and riverine DIN (dissolved inorganic N) export. We used 49 watersheds classified into low-, moderate-, and highly-disturbed categories based on population density to illustrate their differences in nitrogen inputs through atmospheric N deposition, synthetic fertilizers and human emission and DIN export ratios. Our results showed that the island-wide average riverine DIN export is ~ 3800 kg N km-2 yr-1, approximately 18-fold higher than the global average mostly due to the large input of synthetic fertilizers. The average riverine DIN export ratio is 0.30-0.51, which is much higher than the average of 0.20-0.25 of large rivers around the world indicating excessive N input relative to ecosystem demand or retention capacity. The low-disturbed watersheds, despite of high N input, only export 0.06-0.18 of the input so were well buffered to changes in input quantity suggesting high efficiency of nitrogen usage or high N retention capacity of the less disturbed watersheds. The high retention capacity probably is due to the effective uptake by secondary forests in the watersheds. The moderate-disturbed watersheds show a linear increase of output with increases in total N inputs and a mean DIN export ratio of 0.20 to 0.31. The main difference in land use between low and moderately disturbed watershed is the relative proportions of agricultural land and forests, not the built-up lands. Thus, their greater DIN export quantity could be attributed to N fertilizers used in the agricultural lands. The greater export ratios also imply that agricultural lands have lower proportional N retention capacity and that reforestation could be

  8. Metallurgical aspects of welding. Ferrous and nonferrous materials. 4. new rev. ed.

    International Nuclear Information System (INIS)

    Schulze, Guenter

    2010-01-01

    This is the fourth edition of the standard work on welding metallurgy. The various problems of ferrous and nonferrous materials in the welding process are presented in great detail. In order to prevent corrosion of welded constructions, metallurgical properties and problems of all important technical materials are discussed, i.e. alloyed and unalloyed steels, cast iron materials, and the most relevant nonferrous materials. At the end of each chapter, the interested reader will find exercises for self-studies. Some of these can be solved using the material presented in the book while others are intended for deepening and further training. Easy examples (with solutions) are found all over the book; they are helpful because they provide information on underlying mechanisms and interdependences that are not obvious at first glance. The information was adapted to new EURO standards and international standards (up to March 2009) as far as these are relevant to Germany. New information is provided, e.g., on new steel standards (constructional steels according to DIN EN 10025), heat-treatable steels according to DIN EN 10025-6 and DIN EN 10083, high-alloy steels according to DIN EN 10088, and filler materials for steel welding according to DIN EN ISO 2560. The systematics of the ''law of cohabitation'' was applied to welding engineering for the first time here. (orig.) [de

  9. Thin-Sheet zinc-coated and carbon steels laser welding

    International Nuclear Information System (INIS)

    Pecas, P.; Gouveia, H.; Quintino, L.

    1998-01-01

    This paper describes the results of a research on CO 2 laser welding of thin-sheet carbon steels (Zinc-coated and uncoated), at several thicknesses combinations. Laser welding has an high potential to be applied on sub-assemblies welding before forming to the automotive industry-tailored blanks. The welding process is studied through the analysis of parameters optimization, metallurgical quality and induced distortions by the welding process. The clamping system and the gas protection system developed are fully described. These systems allow the minimization of common thin-sheet laser welding defects like misalignment, and zinc-coated laser welding defects like porous and zinc ventilation. The laser welding quality is accessed by DIN 8563 standard, and by tensile, microhardness and corrosion test. (Author) 8 refs

  10. Dinâmica populacional da mariposa oriental em pomares de pessegueiro e ameixeira

    Directory of Open Access Journals (Sweden)

    Hickel Eduardo Rodrigues

    2003-01-01

    Full Text Available O objetivo deste trabalho foi estudar a dinâmica populacional da mariposa oriental [Grapholita molesta (Busk] em pomares de pessegueiro e ameixeira. Os adultos foram monitorados em dois pomares de pessegueiro e um de ameixeira por cinco anos. Séries temporais equivalentes de temperaturas máximas e mínimas foram correlacionadas aos dados de flutuação populacional para se aferir a correspondência entre a ocorrência da praga e as flutuações de temperatura. A análise de Fourier das séries temporais das armadilhas de coleta de mariposas revelou dinâmicas cíclicas, com período principal médio de 53,91 semanas. Um período menor médio, de 7,45 semanas, também ficou evidente e se aproxima do tempo médio de geração do inseto. A análise do espectro de potência das séries temporais, com e sem periodicidade, revelou que a dinâmica populacional de G. molesta possui um componente regular, caracterizado pelos períodos observados, e outro componente irregular, reminiscente de ruído 1/f, caracterizado pelas variações de amplitude, aparentemente irregulares, na ocorrência do inseto. A combinação desses dois componentes ocasiona um processo com domínio de baixas freqüências, próprio das dinâmicas periódicas ruidosas. Os ciclos de aparecimento da praga ocorrem em fase com os ciclos de flutuação de temperaturas máximas e mínimas.

  11. Propiedades mecánicas de uniones obtenidas mediante soldadura por difusión dinámica en un acero de media aleación

    Directory of Open Access Journals (Sweden)

    Gómez de Salazar, J. M.

    2001-04-01

    Full Text Available Mechanical properties in Dynamic Diffusion Bonded (DDB in a A.S.T.M. 1045 steel (0.45 %C joints were studied. The thermomechanical cycle added to the process, favours both the initial deformation stage and probably the diffusion mechanism which participate in bond formation.

    En el presente trabajo se estudian las propiedades mecánicas de uniones obtenidas mediante Soldadura por Difusión Dinámica (SDD en un acero ASTM 1045 (0,45 %C. La aplicación de ciclos termomecánicos en el proceso favorece las etapas iniciales de deformación y, probablemente, los mecanismos difusivos que participan en la formación de la unión.

  12. Mechanical behavior of 9Cr-1Mo-1V steel due to creep fatigue deformation

    International Nuclear Information System (INIS)

    Kim, Sang Tae; Kim, Jae Kyoung; Lee, Hak Sun; Oh, Sang Hyun; Kwun, Sook In; Kim, Chung Seok

    2005-01-01

    Creep-fatigue tests with trapezoid load wave were performed on a 9Cr-1Mo-1V steel at high temperature(550 .deg. C). Trapezoid load wave is considering about hold time for creep effects. we could find out some information in the relationship between number of cycles to failure and hold time. The number of cycles to failure depended on hold time. The cyclic behavior of 9Cr-1Mo-1V steel was characterized by cyclic softening with increasing number of cycles in high temperature. Also we could observe some cavity in the specimens. The size of cavity was different from each hold time

  13. Stress-controlled inelastic behavior of modified 9 Cr-1 Mo steel at elevated temperatures

    International Nuclear Information System (INIS)

    Taguchi, Kosei.

    1989-01-01

    Interest in the ferritic steels of higher chromium concentration has increased recently because of an economical combination of mechanical and corrosion properties at elevated temperatures. A modified 9 Cr-1 Mo ferritic steel, developed in the United States, has been expected as an alternative structural material for fast breeder reactor components, in which Type 304 stainless steel or 2.25 Cr-1 Mo steel is currently used. For application of this material to the structural components, a lot of work has been done to develop evaluation methods for the deformation behavior and strength properties. The authors have studied the inelastic behavior and the creep-fatigue properties of modified 9 Cr-1 Mo steel at elevated temperatures, and proposed a constitutive equation and a creep-fatigue damage equation based on the overstress concept. In this paper, the applicability is discussed of the constitutive equation to stress-controlled inelastic behavior, such as creep strain hardening and stress cycling

  14. DinB Upregulation Is the Sole Role of the SOS Response in Stress-Induced Mutagenesis in Escherichia coli

    Science.gov (United States)

    Galhardo, Rodrigo S.; Do, Robert; Yamada, Masami; Friedberg, Errol C.; Hastings, P. J.; Nohmi, Takehiko; Rosenberg, Susan M.

    2009-01-01

    Stress-induced mutagenesis is a collection of mechanisms observed in bacterial, yeast, and human cells in which adverse conditions provoke mutagenesis, often under the control of stress responses. Control of mutagenesis by stress responses may accelerate evolution specifically when cells are maladapted to their environments, i.e., are stressed. It is therefore important to understand how stress responses increase mutagenesis. In the Escherichia coli Lac assay, stress-induced point mutagenesis requires induction of at least two stress responses: the RpoS-controlled general/starvation stress response and the SOS DNA-damage response, both of which upregulate DinB error-prone DNA polymerase, among other genes required for Lac mutagenesis. We show that upregulation of DinB is the only aspect of the SOS response needed for stress-induced mutagenesis. We constructed two dinB(oc) (operator-constitutive) mutants. Both produce SOS-induced levels of DinB constitutively. We find that both dinB(oc) alleles fully suppress the phenotype of constitutively SOS-“off” lexA(Ind−) mutant cells, restoring normal levels of stress-induced mutagenesis. Thus, dinB is the only SOS gene required at induced levels for stress-induced point mutagenesis. Furthermore, although spontaneous SOS induction has been observed to occur in only a small fraction of cells, upregulation of dinB by the dinB(oc) alleles in all cells does not promote a further increase in mutagenesis, implying that SOS induction of DinB, although necessary, is insufficient to differentiate cells into a hypermutable condition. PMID:19270270

  15. Hydrogen induced plastic damage in pressure vessel steel of 2.25Cr-1Mo

    International Nuclear Information System (INIS)

    Han, G.W.; Song, Y.J.

    1995-01-01

    2.25Cr-1Mo steel is generally employed as a hydrogenation reaction vessel material used at elevated temperature and in a hydrogen containing environment. During service of the reaction vessel, a large number of hydrogen atoms would enter its wall. When the reaction vessel is shutdown and the temperature reduces to about ambient temperature, the hydrogen atoms remaining in the wall would induce plastic damage in the steel. The mechanism of hydrogen induced plastic damage is different for various materials with different microstructures. Investigations have demonstrated that the hydrogen induced plastic damage in carbide annealed carbon steels is caused by hydrogen accelerating the initiating and growing of microvoids from the carbide particles. However, SEM examination on the fracture surface of hydrogen charged tensile specimen of 2.25Cr-1Mo steel show that a large number of fisheyes appear on the fracture surface. This indicates that hydrogen induced plastic damage in 2.25Cr-1Mo steel is related to the occurrence of fisheye cracks during plastic deformation. By means of micro-fracture mechanics to analyze fisheye crack occurrence from the first generation microvoid, the mechanism of hydrogen induced plastic damage in the pressure vessel steel is investigated

  16. La flexibilitat en els àcids nucleics: Un estudi de dinàmica molecular

    OpenAIRE

    Noy Freixa, Agnès

    2008-01-01

    [cat] L'estat de l'art de les simulacions de dinàmica molecular és utilitzat per estudiar l'estructura, dinàmica, propietats d'interacció molecular i flexibilitat dels dúplexs d'ADN i ARN en solució acuosa. Les nostres simulacions suggereixen que el concepte de flexibilitat, rigidesa i deformabilitat són molt més complexes del que habitualment es creu, i que per tant no és sempre veritat que l'ADN sigui més flexible que l'ARN. La dinàmica molecular és a més utilitzada per investigar les prop...

  17. Flexibilitat en els àcids nucleics: Un estudi de dinàmica molecular, La

    OpenAIRE

    Noy Freixa, Agnès

    2008-01-01

    L'estat de l'art de les simulacions de dinàmica molecular és utilitzat per estudiar l'estructura, dinàmica, propietats d'interacció molecular i flexibilitat dels dúplexs d'ADN i ARN en solució acuosa. Les nostres simulacions suggereixen que el concepte de flexibilitat, rigidesa i deformabilitat són molt més complexes del que habitualment es creu, i que per tant no és sempre veritat que l'ADN sigui més flexible que l'ARN.La dinàmica molecular és a més utilitzada per investigar les propietats d...

  18. Aircraft Steels

    Science.gov (United States)

    2009-02-19

    component usage. PH 13-8Mo is a precipitation-hardenable martensitic stainless steel combining excellent corrosion resistance with strength. Custom 465 is...a martensitic , age-hardenable stainless steel capable of about 1,724 MPa (250 ksi) UTS when peak-aged (H900 condition). Especially, this steel can...NOTES 14. ABSTRACT Five high strength steels (4340, 300M, AerMet 100, Ferrium S53, and Hy-Tuf) and four stainless steels (High Nitrogen, 13

  19. Improvements in the susceptibility to hydrogen attack and stress-relief cracking of 2 1/4Cr-1Mo steels

    International Nuclear Information System (INIS)

    Imanaka, T.; Sato, S.; Shimomura, J.; Aso, K.

    1985-01-01

    The influence of sulphur content at extremely low level on the susceptibility to hydrogen attack and stress-relief cracking in 2 1/4Cr-1Mo steels was studied. The reduction of sulphur content and/or the addition of REM (rare earth metal) or Ca in accordance with sulphur content remarkably improve the resistivity against hydrogen attack and stress-relief cracking. Micro-structural examination has showed that there exist Mn-REM-S-Al-O complex particles in the REM-added steels. It is concluded that the effect of REM on hydrogen attack and stress-relief cracking is to reduce ''the free sulphur'' in 2 1/4Cr-1Mo steels

  20. NCRP Report No.151 versus Norm DIN 6847-2; NCRP Report No. 151 vs Norma DIN 6847-2

    Energy Technology Data Exchange (ETDEWEB)

    Sanchez Jimenez, J.; Rivas Ballarin, M. A.

    2008-07-01

    The National Council on Radiation protection and Measurements (NCRP) has recently published its Report No. 151, which presents recommendations and technical information on the design of structural shielding for megavoltage X and gamma-ray radiotherapy facilities. The calculations method introduced by this Report covers aspects like IMRT and other special techniques, as well as the design of structural details like doors, mazes and ducts, or the calculations of skyshine and ground shine radiation. In this work the necessary shielding for a Siemens Oncor treatment unit has been calculated, following NCRP Report No. 151 and DIN 6847-2 standard. In both cases the same isocenter workload W, use factor U, occupancy factor T and shielding design goals P, for workers and public members, are used. The results obtained with DIN 6847 are similar to the ones obtained with this Report, though there are some differences when considering the in-any-one-hour time averaged dose-equivalent rate in low occupancy factor areas, or where scattered radiation reaches the barrier under a small angle. (Author) 9 refs.

  1. Influence of Normalizing Temperature on the Microstructure and Hardness of 9Cr-1Mo ODS Steel

    Energy Technology Data Exchange (ETDEWEB)

    Jang, Ki Nam; Kim, Tae Kyu [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Kim, Kyu Tae [Dongguk University, Gyeongju (Korea, Republic of)

    2016-10-15

    Oxide dispersion strengthened(ODS) steel has superior high-temperature strength and creep properties because fine oxide particles having an excellent stability at high temperatures are uniformly distributed in the matrix. ODS steel has being developed for structure materials of sodium fast cooled reactor(SFR) because of its excellent irradiation resistance and mechanical properties. 9Cr-1Mo ODS steel has better high temperature strength and irradiation resistance than common 9Cr-1Mo steel because Y{sub 2}O{sub 3} nano-sized particles which interrupt dislocation movement and grain boundary slip are uniformly dispersed in the martensite matrix. The mechanical properties of the ODS steels are mainly determined by their microstructures, and the microstructure is considerably decided by the heat-treatment conditions. This study focused on the effect of normalizing temperature on microstructure and hardness of 9Cr-1Mo martensitic ODS steel so as to optimize the heat-treatment condition. In this study, the effect of normalizing temperature on mechanical property and microstructures of 9Cr-1Mo martensitic ODS steel was investigated. It was shown that the microhardness was steadily increased with increasing of the normalizing temperature. According to TEM observation, mechanical property of 9Cr-1Mo ODS steel was significantly affected by lath width. These observations, could be useful to understand the relationship between normalizing temperature and microstructure.

  2. Creep-fatigue-environment interaction of 9Cr-1Mo-V-Nb steel

    International Nuclear Information System (INIS)

    Shibata, Hiroyuki; Ishikawa, Akiyoshi; Asada, Yasuhide

    1996-01-01

    An extension of the creep-fatigue damage model has been conducted in the present study. The original damage model has been developed to the predict the creep-fatigue life of 9Cr-1Mo-V-Nb steel (Modified 9Cr-1Mo steel) in a very high vacuum environment. The present study is to extend an applicability of the model to the creep-fatigue damage accumulation in the air environment. (orig.)

  3. Standard and applied material testing methods of austenitic CrNi stainless steels in different nitric acid media - procedures and results

    International Nuclear Information System (INIS)

    Leistikow, S.; Kraft, R.; Schanz, G.

    1989-07-01

    Extended ASTM Standard Huey Testing has been performed in at 120 0 C boiling 14.4 molar (65%) nitric acid during 15 periods (15x48 = 720 h duration) for quality control of numerous commercial nitric acid resistant austenitic CrNi steels. It was shown how sensitively the chosen testing conditions could differentiate between CrNi steels of the same nominal composition as specified for DIN W.Nr. 1.4306 (AISI Type 304 L), but with varying residual element contents. Within an attempt to differentiate within this group of steels by application of electrochemical methods, potentiostatic tests at 1250 mV in nitric acid of equal concentration and temperature were able to detect remarkable differences in corrosion behaviour already after one hour. Another approach, more typical for the electrochemical potentials during materials application in reprocessing plants of nuclear fuel, gave preference to long-term immersion tests, which were performed in nitric acid of lower concentration and temperature. Reference tests in pure 7 molar, 90 0 C nitric acid could only reveal by surface attack small differences in steel quality by exposures of 720 h duration. To shorten the test time by an increase of the redox potential chromium (VI) ions were added to the nitric acid. In a solution of 0,5 g Gr (VI)/l at 90 0 C remarkable differences in corrosion behavior of the steels - similar to the Huey test results - became measurable by means of gravimetry and metallography already during a short-term exposure of 24-71 h. (orig./MM) [de

  4. Dinámica de objetos transplutonianos: resultados preliminares

    Science.gov (United States)

    Fernández, S.; Brizuela, H.; Roig, F.; Varela, O.

    Se presentan los resultados de una integración numérica de las ecuaciones de movimiento para objetos transplutonianos. Se han calculado los tiempos de Lyapunov para esos objetos y se analiza el comportamiento dinámico de los mismos.

  5. A new implementation of full resolution SBAS-DInSAR processing chain for the effective monitoring of structures and infrastructures

    Science.gov (United States)

    Bonano, Manuela; Buonanno, Sabatino; Ojha, Chandrakanta; Berardino, Paolo; Lanari, Riccardo; Zeni, Giovanni; Manunta, Michele

    2017-04-01

    memory. Moreover, in some processing steps very heavy from the computational point of view, the Graphical Processing Units (GPU) are exploited for the processing of blocks working on a pixel-by-pixel basis, requiring strong modifications on some key parts of the sequential full resolution SBAS-DInSAR processing chain. GPU processing is implemented by efficiently exploiting parallel processing architectures (as CUDA) for increasing the computing performances, in terms of optimization of the available GPU memory, as well as reduction of the Input/Output operations on the GPU and of the whole processing time for specific blocks w.r.t. the corresponding sequential implementation, particularly critical in presence of huge DInSAR datasets. Moreover, to efficiently handle the massive amount of DInSAR measurements provided by the new generation SAR constellations (CSK and Sentinel-1), we perform a proper re-design strategy aimed at the robust assimilation of the full resolution SBAS-DInSAR results into the web-based Geonode platform of the Spatial Data Infrastructure, thus allowing the efficient management, analysis and integration of the interferometric results with different data sources.

  6. Trayectorias evolucionistas en la dinámica de la empresa: una aproximación por dinámica de sistemas

    Directory of Open Access Journals (Sweden)

    Germán Eduardo Vargas

    2006-05-01

    Full Text Available La actividad de las firmas, como unidad socioeconómica, en el marco evolucionista está orientada integralmente por procesos de identidad, cohesión y mecanismos de adaptación y evolución; en este orden, el presente documento ilustra, a través de un modelo por dinámica de sistemas, cómo la orientación e integración estratégica basada en el conocimiento para la innovación se constituye como un imperativo de desarrollo que, a partir de un pequeño apalancamiento, permite distinguir entre dos trayectorias de evolución, a saber: firmas económicas tradicionales (inerciales, pues introducen mejoras incrementales esporádicas y modernas (dinámicas y radicalmente innovadoras, hecho a partir del cual se obtienen reveladoras conclusiones y desafíos para intervenir y adecuar el comportamiento de las empresas.2

  7. The influence of heating rate on reheat-cracking in a commercial 2 1/4Cr1Mo steel

    International Nuclear Information System (INIS)

    Hippsley, C.A.

    1983-03-01

    The effects of elevated heating rate on stress-relief cracking in a commercial 2 1/4 Cr1Mo steel have been investigated. A SEN bend-specimen stress-relaxation test was used to assess reheat cracking susceptibility and fracture mechanisms for an initial post-weld heating rate of 1000 Kh - 1 . Two factors controlling the influence of heating rate on the final severity of cracking were identified, i.e. the rate of stress-relaxation with respect to temperature, and the time available for crack-growth. The factors were found to counteract each other, but in the case of commercial 2 1/4 Cr1Mo steel, the crack-growth factor outweighed the relaxation factor, resulting in a reduction in the propensity to stress-relief cracking at the elevated heating rate. However, by reference to the results of a separate investigation concerning A508/2 MnMoNiCr steel it was demonstrated that the balance between these two factors may be reversed in other alloy systems, with the consequence that reheat cracking is exacerbated by increasing the initial heating rate. A computer model was addressed to the stress-relaxation test conditions using data from the commercial 2 1/4 Cr1Mo steel. The model predictions exhibited reasonable agreement with experimental test results for both 100 Kh - 1 and 1000 Kh - 1 heating rates. (author)

  8. Evaluation of environmental effect on creep-fatigue of 2 1/4Cr-1Mo steel

    International Nuclear Information System (INIS)

    Yang Beinan; Ishikawa, Akiyoshi; Asada, Yasuhide.

    1991-01-01

    In the present study, a trial evaluation was made to evaluate the environmental effect of air separately from the behavior of material origin. Data with 2 1/4Cr-1Mo steel at 550degC in air were subjected to the evaluation based on data of the steel in high vacuum with a newly developed procedure using the overstress concept. An empirical expression was proposed to describe the environmental effect of air on the creep-fatigue behavior. Following conclusions were obtained in the present study on a separation of the environmental effect of air on a creep-fatigue behavior of 2 1/4Cr-1Mo steel at 550degC. 1) The environmental effect of air reduces a fatigue life, that is, it increases the time-independent damage component of the creep-fatigue. 2) The environmental effect of air brings on the frequency effect which is mainly dependent upon a strain rate or time in a compression going stroke. Other environmental effect on F-S or compression hold-time cycles depends upon the strain rate in compression. 3) The rate-time dependent damage component, that is, the creep damage is reduced by the environmental effect of air. That means a creep-fatigue life recovers in air environment. (author)

  9. Mutaciones dinámicas

    Directory of Open Access Journals (Sweden)

    Cesar A. Parra

    1994-10-01

    Full Text Available EI descubrimiento de repeticiones amplificadas de trinucleótidos variables en número, en pacientes con distrofia miotónica, síndrome de X-frágil, corea de Huntington y enfermedad de Kennedy, al igual que alteraciones en dinucleótidos del DNA microsatélite en pacientes con carcinoma proximal de colon, ha dado origen al concepto de mutaciones dinámicas. Esto representa una nueva avenida en teoría genética contemporánea que explica fenómenos como lo anticipación y la paradoja de Sherman que se salen del patrón mendeliano clásico.

  10. origen e impactos de dinópolis

    Directory of Open Access Journals (Sweden)

    Raúl Lardiés Bosque

    2005-01-01

    Full Text Available El parque temático de Dinópolis se ha convertido en uno de los principales atractivos de la provincia de Teruel. Desde que el parque empezó a funcionar en junio de 2001, ya se han empezado a detectar algunos cambios de tipo socioeconómico, no sólo por el aumento del número de visitantes y turistas que llegan a la ciudad de Teruel, sino también por los impactos indirectos que esa afluencia genera en el sector turístico y comercial. En este artículo se analiza la puesta en marcha del proyecto y sus orígenes, así como la influencia socioeconómica que está teniendo a escala local. El enfoque que se ha adoptado es el de considerar a Dinópolis como una herramienta/estrategia de desarrollo local, puesto que se está convertiendo en un reclamo turístico y de visitantes para la ciudad, y porque todo ello genera impactos indirectos importantes en diversos sectores y ramas económicas.

  11. Innovations in the Poetry Form by Sheikh Sa'd od-Din Ahmad Ansari

    Directory of Open Access Journals (Sweden)

    Najaf Jowkar

    2016-05-01

    Full Text Available AbstractSheikh Sa'd od-Din Ahmad َ Ansari, the son of Mawlana Abd ol-Ghaffar Ibn Abd ol-Karim, is a mystic of the 12th and 13th centuries AH. Sa'd od-Din was born in Kabul in the village called Yahya Yahyaee in 1140 AH and died in the same place in 1225 AH (Ansari, 1374: 6. In his youth, he learned canonical law and theology from his father but was soon attracted to mysticism (Heravi, 1373, 43. After performing Hajj in between the years 1169-113 AH and getting permission to guide people from Naqshbandiyeh and Qaderiyeh mystic Sheikh Mohammad Saman Madani, he returned home and guided people untill the end of his life (Ansari, 1390: 3. Sheikh Sa'd od-Din was well learned in Islamic studies, Arabic language, rhetoric and sciences of his time. He was also familiar with the works of poets such as 'Attar, Rumi, Hafez, Ibn Arabi and other great names of mysticism. He was attached to Rumi and Hafez and has quoted them frequently in his works.Sheikh Sa'd od-Din wrote thirty six books and treatises including seven Divans and two Masnavis in Persian; He also wrote a book entitled The Mine of Unity and treatises  such as "Greetings Noble Tatar", "Habl ol-Matin" and "The Elite" in Arabic. He composed some poems in Arabic as well.At least from 1174 AH Sheikh Sa'd od-Din started to bring changes to the ancient Persian poetry; thus his deconstruction made poetical form much similar to contemporary Persian poetry. However, due to political and cultural distance between Iran and Afghanistan, we did not have a chance to get familiar with his innovations.His innovations consist of the following:1.      Refrained Masnavi (masnavi tarjee'band: He changed masnavi in a way that we can call it refrained masnavi, a sample of which is included in the paper. It consists of fifteen stanzas: The first stanza with eight lines, the second stanza fifty four lines, the twelfth stanza eleven lines and the other stanzas having equal lines. The line between

  12. Creep-fatigue behavior of 2 1/4Cr-1Mo steel at 5500C in air and vacuum

    International Nuclear Information System (INIS)

    Asayama, T.; Cheng, S.Z.; Asada, Y.; Mitsuhashi, S.; Tachibana, Y.

    1987-01-01

    Creep-fatigue tests were conducted with 2 1/4Cr-1Mo steel at 550 0 C under various strain wave forms in air and vacuum of 100 and 0.1 μPa. No indication of environmental effect of air was observed in 0.1 μPa vacuum in which a strain rate effect diminished. However, there observed still a time/rate dependent life reduction in a case of wave forms with a longer tension going time than compression. In addition, there observed an effect of mean stress with this steel. An analysis of stress-strain response showed the response is not affected by the test environment. Internal stresses of back and drag stress were obtained with this steel and an overstress was predicted based on phenomenology. A pure creep-fatigue life reduction was predicted based on a damage model composed of the overstress. The prediction showed a scatter of a factor of two. An effect of air environment was evaluated based on the prediction procedure. The method should be improved to include the effect of mean stress on creep-fatigue behavior of this steel

  13. Correlation of microstructure and low cycle fatigue properties for 13.5Cr1.1W0.3Ti ODS steel

    International Nuclear Information System (INIS)

    He, P.; Klimenkov, M.; Möslang, A.; Lindau, R.; Seifert, H.J.

    2014-01-01

    Reduced activation oxide dispersion strengthened (ODS) steels are prospective structural materials for the blanket system and first wall components in Tokamak-type fusion reactors. Under the pulsed operation, these components will be predominantly subjected to cyclic thermal–mechanical loading which leads to inevitable fatigue damage. In this work, strain controlled isothermal fatigue tests were conducted for 13.5Cr1.1W0.3Ti ODS steel at 550 °C. The total strain range varied from 0.54% to 0.9%. After thermomechanical processing, 13.5CrWTi–ODS steel exhibits a remarkable lifetime extension with a factor of 10–20 for strain ranges Δε ⩽ 0.7%. 13.5Cr ODS steel shows no cyclic softening at all during the whole testing process irrespective of the strain range. TEM observations reveal ultrastable grain structure and constant dislocation densities around 10 14 m −2 , independent of the number of cycles or the applied strain amplitude. The presence of the stabilized ultrafine Y–Ti–O dispersoids enhances the microstructural stability and therefore leads to outstanding fatigue resistance for 13.5Cr1.1W0.3Ti–ODS steel

  14. Correlation of microstructure and low cycle fatigue properties for 13.5Cr1.1W0.3Ti ODS steel

    Energy Technology Data Exchange (ETDEWEB)

    He, P., E-mail: pei.he@kit.edu; Klimenkov, M.; Möslang, A.; Lindau, R.; Seifert, H.J.

    2014-12-15

    Reduced activation oxide dispersion strengthened (ODS) steels are prospective structural materials for the blanket system and first wall components in Tokamak-type fusion reactors. Under the pulsed operation, these components will be predominantly subjected to cyclic thermal–mechanical loading which leads to inevitable fatigue damage. In this work, strain controlled isothermal fatigue tests were conducted for 13.5Cr1.1W0.3Ti ODS steel at 550 °C. The total strain range varied from 0.54% to 0.9%. After thermomechanical processing, 13.5CrWTi–ODS steel exhibits a remarkable lifetime extension with a factor of 10–20 for strain ranges Δε ⩽ 0.7%. 13.5Cr ODS steel shows no cyclic softening at all during the whole testing process irrespective of the strain range. TEM observations reveal ultrastable grain structure and constant dislocation densities around 10{sup 14} m{sup −2}, independent of the number of cycles or the applied strain amplitude. The presence of the stabilized ultrafine Y–Ti–O dispersoids enhances the microstructural stability and therefore leads to outstanding fatigue resistance for 13.5Cr1.1W0.3Ti–ODS steel.

  15. Dinámica de sistemas en la gestión de inventarios

    Directory of Open Access Journals (Sweden)

    Daniel Alejandro Agudelo Serna

    2018-02-01

    Full Text Available En el presente artículo se estudia el proceso de gestión de inventarios por medio de la dinámica de sistemas, como herramienta metodológica que permite conocer el comportamiento de las variables de acuerdo a sus relaciones y a las decisiones que se tomen teniendo en cuenta su causalidad y realimentación. El desarrollo del documento está determinado por una revisión de conceptos teóricos relacionados con la gestión de inventarios y dinámica de sistemas, seguido por una revisión de literatura, en donde se analizan modelos dinámicos que relacionan las variables que afectan directa o indirectamente al inventario, resaltando la importancia de modelos robustos que permitan obtener mejores resultados y así poder establecer políticas de gestión y control del inventario. El objetivo fundamental es presentar una revisión de los modelos dinámicos relacionados con el inventario, en donde es posible observar los diagramas causales y de Forrester, variables, criterios y parámetros que influyen en cada uno de los sistemas presentados. Se supone una metodología basada en la búsqueda de información, para posteriormente desarrollar un análisis detallado de cada modelo encontrado.

  16. Electrochemical studies of novel corrosion inhibitor for mild steel in 1 M hydrochloric acid

    Directory of Open Access Journals (Sweden)

    Ahmed A. Al-Amiery

    2018-06-01

    Full Text Available The electrochemical performance of a novel organic corrosion inhibitor 6-(4-hydroxyphenyl-3-mercapto-7,8-dihydro-[1,2,4]triazolo[4,3-b][1,2,4,5]tetrazine [HT3], for mild steel in 1 M hydrochloric acid is evaluated by potentiodynamic curves. The experimental results show that the investigated inhibitor [HT3], which can effectively retard the corrosion process that occurs to mild steel with a hydrochloric acid solution by providing a protective coating for the mild steel that, can be weakened by increasing the temperature. Furthermore, the inhibition efficiency of [HT3] increased with increasing the concentrations of the inhibitors and decreased with increasing temperature. Keywords: Corrosion, Inhibitor, Mild steel, Potentiodynamic polarization, HT3, NMR, FT-IR

  17. Una propuesta metodológica para extraer factores comunes dinámicos estacionales y no estacionarios

    OpenAIRE

    Orozco Sánchez, María Camila

    2013-01-01

    Este trabajo presenta una metodóloga empírica que permite extraer factores comunes dinámicos estacionales y no estacionarios, basados en el análisis factorial dinámico estacional de Nieto et al. (2013), en el análisis factorial dinámico de Peña y Poncela (2006) y en el modelo de estacionalidad común en diferentes frecuencias planteado por Busetti (2006). La metodología propuesta es aplicada a nueve series de la macroeconomía Colombiana

  18. Microbial-Influenced Corrosion of Corten Steel Compared with Carbon Steel and Stainless Steel in Oily Wastewater by Pseudomonas aeruginosa

    Science.gov (United States)

    Mansouri, Hamidreza; Alavi, Seyed Abolhasan; Fotovat, Meysam

    2015-07-01

    The microbial corrosion behavior of three important steels (carbon steel, stainless steel, and Corten steel) was investigated in semi petroleum medium. This work was done in modified nutrient broth (2 g nutrient broth in 1 L oily wastewater) in the presence of Pseudomonas aeruginosa and mixed culture (as a biotic media) and an abiotic medium for 2 weeks. The behavior of corrosion was analyzed by spectrophotometric and electrochemical methods and at the end was confirmed by scanning electron microscopy. The results show that the degree of corrosion of Corten steel in mixed culture, unlike carbon steel and stainless steel, is less than P. aeruginosa inoculated medium because some bacteria affect Corten steel less than other steels. According to the experiments, carbon steel had less resistance than Corten steel and stainless steel. Furthermore, biofilm inhibits separated particles of those steels to spread to the medium; in other words, particles get trapped between biofilm and steel.

  19. Austenitic chromium nickel steel as standard reference material in measurement of thermal and temperature conductivity

    International Nuclear Information System (INIS)

    Binkele, L.

    1990-01-01

    A niobium-stabilized CrNi steel with the NBS designation SRM 735 is introduced as WLF standard reference material in a report by Hust and Giarratano, for the temperature range 300-1200 K and for thermal conductivities around 20 W/mk. However, its specification does not show it to be a direct member of the DIN family of CrNi steels. This report should be regarded as a continuation and supplement to the above-mentioned efforts in America. On the one hand, a solution of a possibly too-narrow specification is aimed at for the reference material, where it is important how sensitive the thermal conductivity is to changes in the chemical composition and changes of the manufacturing parameters and what accuracy can be reached for the reference values with the best measurement techniques. On the other hand, the data base should be expanded and the accuracy of the reference curve should be improved if possible. (orig./MM) [de

  20. Effect of Plasma Nitriding Process Conditions on Corrosion Resistance of 440B Martensitic Stainless Steel

    Directory of Open Access Journals (Sweden)

    Łępicka Magdalena

    2014-09-01

    Full Text Available Martensitic stainless steels are used in a large number of various industrial applications, e.g. molds for plastic injections and glass moldings, automotive components, cutting tools, surgical and dental instruments. The improvement of their tribological and corrosion properties is a problem of high interest especially in medical applications, where patient safety becomes a priority. The paper covers findings from plasma nitrided AISI 440B (PN-EN or DIN X90CrMoV18 stainless steel corrosion resistance studies. Conventionally heat treated and plasma nitrided in N2:H2 reaction gas mixture (50:50, 65:35 and 80:20, respectively in two different temperature ranges (380 or 450°C specimens groups were examined. Microscopic observations and electrochemical corrosion tests were performed using a variety of analytical techniques. As obtained findings show, plasma nitriding of AISI 440B stainless steel, regardless of the process temperature, results in reduction of corrosion current density. Nevertheless, applying thermo-chemical process which requires exceeding temperature of about 400°C is not recommended due to increased risk of steel sensitization to intergranular and stress corrosion. According to the results, material ion nitrided in 450°C underwent leaching corrosion processes, which led to significant disproportion in chemical composition of the corroded and corrosion-free areas. The authors suggest further research into corrosion process of plasma nitrided materials and its degradation products.

  1. Globalization of Japanese steel industry. Part 1. Materials; Tekkogyo no kokusaika. 1. Zairyo

    Energy Technology Data Exchange (ETDEWEB)

    Aramaki, T. [Nippon Steel Corp., Tokyo (Japan)

    1995-01-01

    This paper discusses the globalization of the Japanese steel industry from the viewpoint of maintenance of international competitive potential. In the steel industry, remarkable technology innovation is currently occurring in the production process. The direct iron ore smelting process and strip caster process are being developed. These innovative technologies are characterized by processes having simplified facilities and lower fixed costs. A large problem of Japanese steel industry is the maintenance of competitive potential in the international price. For the purpose of the cost reduction, profitability improvement efforts have been made, as for the cut of research and development cost, consolidation of standards, intensive production, specialization among undertakings, cooperations, etc. Additionally, accompanied with the overseas production of steel consumers, the overseas steel production has been conducted. The overseas production is currently focused on Asia. Significance of the Japanese steel industry in Asia is provided from the viewpoint of accumulating technological know-how, establishment of new technologies, acquisition of operation technologies, promotion of talented persons for industries, etc. 12 refs., 7 figs., 3 tabs.

  2. The influence of He on the high temperature fracture of an austenitic stainless steel

    International Nuclear Information System (INIS)

    Saguees, A.A.

    1976-01-01

    The Ti-stabilised DIN 1.4970 austenitic stainless steel is an important candidate for high temperature - high neutron fluence applications which will create appreciable amounts of He within the matrix. In order to determine the mechanical effects associated with the presence of He alone a set of tensile specimens was cyclotron implanted to uniform He concentrations in the 10 -6 to 10 -4 at. range and later creep tested at 700 0 C and 800 0 C. The elongation to fracture values of the implanted specimens were reduced with respect to those of unimplanted controls. Scanning Electron Microscope (SEM) examination revealed that fracture starts as intergranular and subsequently propagates in a transgranular fashion, the intergranular part being much more extended in the implanted material. Transmission Electron Microscope (TEM) examination revealed He segregation at the grain boundary precipitates. A mechanism of He embrittlement is discussed in terms of the present results

  3. Thermal fatigue strength estimation of 2.25Cr-1Mo steel under creep-fatigue interaction

    International Nuclear Information System (INIS)

    Kuwahara, Kazuo; Nitta, Akihito; Kitamura, Takayuki

    1980-01-01

    A 2-1/4Cr-1Mo steel is one of principal materials for high temperature equipments in nuclear and thermal power plants. The authors experimentally analyzed the high temperature fatigue strength and creep strength of a 2-1/4 Cr-1Mo steel main steam pipe which had been used in a thermal plant for operation up to 130,000 hours, and pointed out that the strain-range vs. life curves crossed each other due to the difference of temperature-strain phase in thermal fatigue. This suggests that it is difficult to estimate thermal fatigue life of steel materials having been subjected to different temperature-strain phase on the basis of isothermal low-cycle fatigue life at the upper limit temperature of thermal fatigue, and that it is urgently required to establish an appropriate method of evaluating thermal fatigue life. The authors attempted to prove that the strain range partitioning method used for the evaluation of thermal fatigue life in SUS 304 steels is applicable to this 2-1/4Cr-1Mo steel. Consequently, it was found that the thermal fatigue life could be estimated within a factor of 2.5 by the application of this method. (author)

  4. The DinB•RecA complex of Escherichia coli mediates an efficient and high-fidelity response to ubiquitous alkylation lesions.

    Science.gov (United States)

    Cafarelli, Tiziana M; Rands, Thomas J; Godoy, Veronica G

    2014-03-01

    Alkylation DNA lesions are ubiquitous, and result from normal cellular metabolism as well as from treatment with methylating agents and chemotherapeutics. DNA damage tolerance by translesion synthesis DNA polymerases has an important role in cellular resistance to alkylating agents. However, it is not yet known whether Escherichia coli (E. coli) DNA Pol IV (DinB) alkylation lesion bypass efficiency and fidelity in vitro are similar to those inferred by genetic analyses. We hypothesized that DinB-mediated bypass of 3-deaza-3-methyladenine, a stable analog of 3-methyladenine, the primary replication fork-stalling alkylation lesion, would be of high fidelity. We performed here the first kinetic analyses of E. coli DinB•RecA binary complexes. Whether alone or in a binary complex, DinB inserted the correct deoxyribonucleoside triphosphate (dNTP) opposite either lesion-containing or undamaged template; the incorporation of other dNTPs was largely inefficient. DinB prefers undamaged DNA, but the DinB•RecA binary complex increases its catalytic efficiency on lesion-containing template, perhaps as part of a regulatory mechanism to better respond to alkylation damage. Notably, we find that a DinB derivative with enhanced affinity for RecA, either alone or in a binary complex, is less efficient and has a lower fidelity than DinB or DinB•RecA. This finding contrasts our previous genetic analyses. Therefore, mutagenesis resulting from alkylation lesions is likely limited in cells by the activity of DinB•RecA. These two highly conserved proteins play an important role in maintaining genomic stability when cells are faced with ubiquitous DNA damage. Kinetic analyses are important to gain insights into the mechanism(s) regulating TLS DNA polymerases. Copyright © 2013 Wiley Periodicals, Inc.

  5. Effect of HIP temperature and cooling rate on microstructure and hardness of joints for ODS-RAFM steels and JLF-1 steel

    International Nuclear Information System (INIS)

    Fu, Haiying; Nagasaka, Takuya; Muroga, Takeo; Kimura, Akihiko; Ukai, Shigeharu

    2016-01-01

    Dissimilar-metal joints between ODS-RAFM (oxide-dispersion-strengthened reduced activation ferritic/martensitic) steels and JLF-1 steel were fabricated by hot isostatic pressing (HIP) at 1000 - 1100degC with a cooling rate of 5degC/min. After the HIP, it was always quenched martensite for JLF-1 steel. However, coarse precipitates were found in 9Cr-ODS. Additional annealing experiments to simulate HIP conditions were conducted for 9Cr-ODS with cooling rate ranged from 0.5 to 36degC/min at 800 - 1100degC. The results showed that, to form quenched martensite for 9Cr-ODS, the HIP temperature should be above 1000degC with cooling rate no less than 25dgeC/min. When the cooling rate is increased to 36degC/min, the microstructure of 9Cr-ODS is quenched martensite with precipitate size similar as that before HIP. If the limitation of precipitate size in 9Cr-ODS is 0.2 µm, HIP temperature above 1050degC with cooling rate no less than 30degC/min is needed. In this case, post-weld heat treatment (PWHT) with only tempering is necessary to recover the microstructure of 9Cr-ODS to tempered martensite. For 12Cr-ODS, the HIP temperature and cooling rate has no effect on hardness and precipitate size. PWHT is not necessary for the single-metal joint of 12Cr-ODS from the view point of precipitation control. However, for the dissimilar-metal joints between ODS-RAFM steels and JLF-1 steel, the PWHT condition should be comprehensively determined by considering microstructural evolution of each part in the joints after HIP. (author)

  6. The corrosion of austenitic steel in flowing high-temperature water

    International Nuclear Information System (INIS)

    Asmundis, C. de; Weisgerber, P.; Mazzocchi, N.; Plog, C.

    1981-01-01

    This work represents an attempt to obtain data on the corrosion product formation, including corrosion products which are released to the water, of austenitic steel. AISI 316 or DIN Werkstoff No. 14401. The oxidation experiments were carried out in a small laboratory test loop, which was designed for this study. In the stainless water system considered during an oxidation time of 1800 h at 300 0 C, five zones of differing composition developed. 1. The base metal (for comparison) Fe/Cr/Ni = 67/20/13. 2. The metal at the metal/oxide interface nickel enriched, chromium and iron decreased Fe/Cr/Ni = 64/19/17. 3. The inner oxide chromium enriched and iron and nickel decreased Fe/Cr/Ni = 53/32/14. 4. The outer oxide iron enriched, chromium decreased Fe/Cr/Ni = 70/17/13. 5. The corrosion products released to the water, in total, i.e. particulate and dispersed matter, a Fe/Cr/Ni ratio rather close to that base metal: Fe/Cr/Ni = 68/19/13. (80% particulate: Fe/Cr/Ni = 72/23/5, 20% dispersed: Fe/Cr/Ni = 55/1/44)

  7. Estudio dinámico de un potencial perturbador dependiente de dos parámetros

    Science.gov (United States)

    Miloni, O.; Brunini, A.

    El objeto del presente trabajo consiste en el estudio dinámico de un sistema dinámico caracterizado por la función hamiltoniana correspondiente a un satélite planetario perturbado por la acción del Sol y del achatamiento del planeta madre. Cuando dicha Hamiltoniana se promedia respecto de los términos de corto período, esta queda con dos grados de libertad, y su estudio puede ser realizado con las herramientas clásicas de la dinámica no-lineal. Se tratará de determinar regiones regulares y caóticas de movimiento. En el caso de estas últimas, es de particular interés la determinación de su orígen.

  8. Regulated expression of the dinR and recA genes during competence development and SOS induction in Bacillus subtilis

    NARCIS (Netherlands)

    Haijema, BJ; vanSinderen, D; Winterling, K; Kooistra, J; Venema, G; Hamoen, LW

    1996-01-01

    It has been hypothesized that the dinR gene product of Bacillus subtilis acts as a repressor of the SOS regulon by binding to DNA sequences located upstream of SOS genes, including dinR and recA. Following activation as a result of DNA damage, RecA is believed to catalyse DinR-autocleavage, thus

  9. Lifetime of Manet steel in load-cycling tests in vacuum at 20 and 550deg C

    International Nuclear Information System (INIS)

    Ullmaier, H.; Schmitz, W.

    1989-01-01

    Fatigue tests in vacuum were carried out on the Manet heat of DIN 1.4914 martensitic steel (X13Cr10.7Ni0.85Mo0.75V0.22) in push-pull type, stress-controlled experiments at room temperature and 823 K. The fatigue life was determined as a function of stress amplitude, mean stress, frequency and hold time. At 823 K creep has a strong influence on the life time, particularly at low frequencies and long hold times in tension. The results are phenomenologically described by a simple linear damage summation approach. Even at room temperature the life time of specimens tested in vacuum is about an order of magnitude higher than of those tested in air. This stresses the importance of providing the correct test environment in collecting fatigue data for the design of fusion devices. (orig./MM)

  10. Fabrication of Hadfield-Cored Multi-layer Steel Sheet by Roll-Bonding with 1.8-GPa-Strength-Grade Hot-Press-Forming Steel

    Science.gov (United States)

    Chin, Kwang-Geun; Kang, Chung-Yun; Park, Jaeyeong; Lee, Sunghak

    2018-05-01

    An austenitic Hadfield steel was roll-bonded with a 1.8-GPa-strength-grade martensitic hot-press-forming (HPF) steel to fabricate a multi-layer steel (MLS) sheet. Near the Hadfield/HPF interface, the carburized and decarburized layers were formed by the carbon diffusion from the Hadfield (1.2%C) to HPF (0.35%C) layers, and could be regarded as kinds of very thin multi-layers of 35 μm in thickness. The tensile test and fractographic data indicated that the MLS sheet was fractured abruptly within the elastic range by the intergranular fracture occurred in the carburized layer. This was because C was mainly segregated at prior austenite grain boundaries in the carburized layer, which weakened grain boundaries to induce the intergranular fracture. In order to solve the intergranular facture problem, the MLS sheet was tempered at 200 °C. The stress-strain curve of the tempered MLS sheet lay between those of the HPF and Hadfield sheets, and a rule of mixtures was roughly satisfied. Tensile properties of the MLS sheet were dramatically improved after the tempering, and the intergranular fracture was erased completely. In particular, the yield strength up to 1073 MPa along with the high strain hardening and excellent ductility of 32.4% were outstanding because the yield strength over 1 GPa was hardly achieved in conventional austenitic steels.

  11. Hydrogen attack of steel. Progress report, April 1, 1978--March 31, 1979

    International Nuclear Information System (INIS)

    Shewmon, P.G.

    1978-01-01

    Four normalized carbon steels made in different ways (Si-killed, Al-killed, REM-treated, and electroslag refined) were studied to determine the role of differing fine inclusions on the early stages of hydrogen attack (HA). Hydrogen exposures were made at 450 0 C (6.5 MPa) and 375 0 C (7.6 MPa). The first stage of HA is shown to be the development of a closely spaced (1-2 μm) array of small bubbles over the ferrite/pearlite, or occasionally the ferrite/ferrite boundaries. These grew together to form tears, primarily in the rolling plane, leading to more rapid expansion normal to this plane. The planes of separation followed high solute layers in banded steel but only rarely did the fracture surfaces follow inclusions. At 450 0 C REM-treated steel was attacked the fastest and the Al-killed steel took two to four times as long for attack

  12. Effects of welding on toughness of Mod. 9Cr-1Mo steel

    International Nuclear Information System (INIS)

    Ryu, W. S.; Kim, S. H.; Yoon, J. H.

    2008-01-01

    Nuclear energy is being seriously considered to meet the increasing demand for a world-wide energy supply without environmental effects. Generation IV reactors are being developed to produce a reliable energy safely and with an economic benefit. Since these new reactors require an elevated temperature, ferritic/martensitic steels are attracting attention as candidate materials for the reactor vessel of a very high temperature reactor (VHTR) and the cladding of a sodium fast reactor (SFR,) due to their high strength and thermal conductivity, low thermal expansion, and good resistance to corrosion. in recent years, new ferritic/martensitic steels have been developed for ultra supercritical fossil power plants. Advanced technologies for a steel fabrication have improved the elevated temperature properties of ferritic/martensitic steels to make them comparable with austenitic stainless steels. The microstructural stability of the pressure vessel, cladding and core structural materials of the VHTR and SCWR is very important. Welding process affects the microstructure and residual stress, so the toughness of ferritic/martensitic steels decreases in general. In this paper; Mod. 9Cr-1Mo steel is welded by SMAW with V-groove, and the effects of welding on tensile and impact properties are evaluated. The upper self energy of the weldment was only 57% of that of the base metal, and the DBTT T 41J and T 68J index temperatures of the weldment were higher than those of the base metal by 17 deg. C, 38 deg. C and 37 deg. C, respectively. (authors)

  13. Analysis for Producing a Facsimile of the Cadastral Map of Varaždin

    Directory of Open Access Journals (Sweden)

    Mirko Husak

    2012-12-01

    Full Text Available This paper investigates and suggests methods for producing a facsimile of the 1 860 cadastral map of Varaždin. The methods used to produce the map, the coordinate systems, map contents, usage, maintenance and damage are described. Three samples from the map that display the elements of damage noted were researched, and the possibility of replacing damaged sections with undamaged sections using digital methods investigated. The sources available were the original cadastral colour map of Varaždin, along with the line art cadastral map and field cadastral sketches. The original colour and line art maps were scanned using the DeSkan Express scanning system for large formats. A flatbed UMAX Mirage II A3 scanner was used for scanning the field cadastral map. For the research image-processing, Adobe Photoshop CE 7.0 software was used, although it was primarily designed for processing photographs. The colour separation method was rejected from the start, since the map was made by hand. The paper discusses the possibility of copying and inserting missing parts from additional map sources, changing the colour of the paper to white or another colour, removing the map content added in red ink and lead pencil, and so on. The discussion is based on actual examples from the digital image. The conclusion suggests image-processing methods for achieving optimal results in producing a facsimile of the Varaždin cadastral map.Keywords: facsimile; cadastral map; map content; scanning; digital image processing

  14. Characteristics of Modified 9Cr-1Mo Steel for Reactor Pressure Vessel of Very High Temperature Gas Cooled Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Sung Ho; Ryu, W. S.; Han, Chang Hee; Yoon, J. H.; Chang, Jong Hwa

    2004-11-15

    Many researches and developments have been progressed for the construction of VHTR by 2020 in Korea. Modified 9Cr-1Mo steel has been receiving attention for the application to the reactor pressure vessel material of VHTR. We collected and analyzed the research data for modified 9Cr-1Mo steel in order to understand the characteristics of modified 9Cr-1Mo steel. The modified 9Cr-1Mo steel is a modified alloy system similar to conventional 9Cr-1Mo grade ferritic steel. Modifications include additions of vanadium, niobium, and nitrogen, as well as lower carbon content. In this report, we summarized the change of microstructure and mechanical properties after tempering, thermal aging, and irradiation. Modified 9Cr-1Mo steel has high strength and thermal conductivity, low thermal expansion, and good resistance to corrosion. But the irradiation embrittlement behavior of modified 9Cr-1Mo steel should be evaluated and the evaluation methodology also should be developed. At the same time, the characteristics of weldment which is the weak part in pressure vessel should be evaluated.

  15. Mand træn din bækkenbund og få bedre rejsning

    DEFF Research Database (Denmark)

    Ravnkilde Marlet, Laila; Gerbild, Helle Nygaard

    2016-01-01

    Har du (eller din mand) problemer med at holde på urin eller at opnå eller bevare rejsningen, er der god grund til at søge hjælp. Der findes nemlig effektive og billige behandlingsmuligheder.......Har du (eller din mand) problemer med at holde på urin eller at opnå eller bevare rejsningen, er der god grund til at søge hjælp. Der findes nemlig effektive og billige behandlingsmuligheder....

  16. Análise do comportamento dinâmico em pontes pedonais

    OpenAIRE

    Valentim, Nilton Leonardo

    2012-01-01

    Dissertação para obtenção do Grau de Mestre em Engenharia Civil - Perfil Estruturas A análise do comportamento dinâmico de estruturas de engenharia civil tem um interesse evidente para a avaliação dos efeitos das acções de sismos, vento e tráfego ferroviário, rodoviário ou pedonal. O interesse desta avaliação estende-se também à própria caracterização global do estado das estruturas, uma vez que as propriedades dinâmicas estão directamente relacionadas com esse estado. Pa...

  17. Study on Creep Damage Model of 1Cr1Mo1/4V Steel for Turbine Rotor

    International Nuclear Information System (INIS)

    Choi, Woo Sung; Song, Gee Wook; Kim, Bum Shin; Chang, Sung Ho; Fleury, Eric

    2011-01-01

    It is well known that the dominant damage mechanisms in high-temperature steam turbine facilities such as rotor and casing are creep and fatigue damages. Even though coupling of creep and fatigue should be considered while predicting the life of turbine facilities, the remaining life of large steam turbine facilities is generally determined on the basis of creep damage because the turbines must generate stable base-load power and because they are operated at a high temperature and pressure for a long time. Almost every large steam turbine in Korea has been operated for more than 20 years and is made of steel containing various amounts of principal alloying elements nickel, chromium, molybdenum, and vanadium. In this study, creep damage model of 1Cr1Mo1/4V steel for turbine rotor is proposed and that can assess the high temperature creep life of large steam turbine facilities is proposed

  18. Welded joint properties of steel 2.25Cr1MoNiNb

    International Nuclear Information System (INIS)

    Gladis, R.; Ivanek, J.; Gottwald, M.

    1981-01-01

    Welded joints of steel 08Cr2.25Mo1NiNb for fast reactor steam generators made using manual arc welding with electrodes of identical compositions attain short-term mechanical properties and times to fracture when creep tested that match those of the base material. The reduction of the carbidic phase content in the steel and the welded joint metal did not adversely affect the tensile properties of the welded joint while increasing notch toughness of the heat-affected zone. Reduced carbon and niobium contents in the steel and the welded joint resulted in significant reduction in the proportion of carbidic eutectic particles in both the heat-affected zone and the weld metal. (Ha)

  19. Heat treated 9 Cr-1 Mo steel material for high temperature application

    Science.gov (United States)

    Jablonski, Paul D.; Alman, David; Dogan, Omer; Holcomb, Gordon; Cowen, Christopher

    2012-08-21

    The invention relates to a composition and heat treatment for a high-temperature, titanium alloyed, 9 Cr-1 Mo steel exhibiting improved creep strength and oxidation resistance at service temperatures up to 650.degree. C. The novel combination of composition and heat treatment produces a heat treated material containing both large primary titanium carbides and small secondary titanium carbides. The primary titanium carbides contribute to creep strength while the secondary titanium carbides act to maintain a higher level of chromium in the finished steel for increased oxidation resistance, and strengthen the steel by impeding the movement of dislocations through the crystal structure. The heat treated material provides improved performance at comparable cost to commonly used high-temperature steels such as ASTM P91 and ASTM P92, and requires heat treatment consisting solely of austenization, rapid cooling, tempering, and final cooling, avoiding the need for any hot-working in the austenite temperature range.

  20. Corrosion behaviour of the welded steel 1.4313/CA6-NM

    OpenAIRE

    Lovíšek, Martin; Liptáková, Tatiana; Pešlová, Františka

    2014-01-01

    The stainless steel 1.4313/CA6-NM (EN X3CrNiMo13-4) is used for turbine production. The weld joints are therefore very sensitive localities from mechanical and corrosion point of view. The subject of the work is corrosion studying of the steel welded by TIG method with consequent heat treatment. Corrosion resistance of the weld joints and base material are evaluated through potentiodynamic polarization test measured on the surface after heat treatment and on the surface cleaned by grinding an...

  1. Effect of substructure on mechanical properties and fracture behavior of lath martensite in 0.1C–1.1Si–1.7Mn steel

    Energy Technology Data Exchange (ETDEWEB)

    Li, Shengci [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Zhu, Guoming, E-mail: zhuguoming@ustb.edu.cn [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Kang, Yonglin, E-mail: kangylin@ustb.edu.cn [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); State Key Laboratory for Advanced Metals and Materials, University of Science and Technology Beijing, Beijing 100083 (China)

    2016-08-05

    The purpose of this study was to analyze the microstructure of lath martensite in 0.1C–1.1Si–1.7Mn (wt.%) steel and its effect on mechanical properties and fracture behavior. The microstructure was characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and electron back scattering diffraction (EBSD). Charpy V-notch impact samples and compact tension (CT) samples were used to investigate the Charpy impact properties and fatigue crack growth behavior of the steel, respectively. The propagation of cleavage crack and fatigue crack were analyzed to figure out the effective grain size. The results showed that the typical hierarchical lath martensite structure contained prior austenite grains, packets, blocks and laths; packet size and block width were positively correlated to prior austenite grain size, while lath width was maintained at about 0.29 μm. Yield strength was related to prior austenite grain size, packet size and block width, and obeyed Hall–Petch relationship. Grain refinement was effective in improving the resistance to cleavage fracture by introducing barriers to crack propagation; packet boundaries and block boundaries hold similar ability to impede the propagation of crack. Paris model can well describe the FCG behavior of the investigated steel. Block width governs the effective grain size for strength, toughness and fatigue crack propagation. - Graphical abstract: Mechanical properties and fracture behavior of 0.1C–1.1Si–1.7Mn steel. - Highlights: • Hall–Petch relationship is obeyed between yield strength and martensite microstructure size. • Packet boundaries and block boundaries hold similar ability to impede the propagation of crack. • Block width is the effective grain size for strength, toughness and fatigue crack propagation.

  2. Metallurgical aspects of welding. Ferrous and nonferrous materials. 4. new rev. ed.; Die Metallurgie des Schweissens. Eisenwerkstoffe - nichteisenmetallische Werkstoffe

    Energy Technology Data Exchange (ETDEWEB)

    Schulze, Guenter

    2010-07-01

    This is the fourth edition of the standard work on welding metallurgy. The various problems of ferrous and nonferrous materials in the welding process are presented in great detail. In order to prevent corrosion of welded constructions, metallurgical properties and problems of all important technical materials are discussed, i.e. alloyed and unalloyed steels, cast iron materials, and the most relevant nonferrous materials. At the end of each chapter, the interested reader will find exercises for self-studies. Some of these can be solved using the material presented in the book while others are intended for deepening and further training. Easy examples (with solutions) are found all over the book; they are helpful because they provide information on underlying mechanisms and interdependences that are not obvious at first glance. The information was adapted to new EURO standards and international standards (up to March 2009) as far as these are relevant to Germany. New information is provided, e.g., on new steel standards (constructional steels according to DIN EN 10025), heat-treatable steels according to DIN EN 10025-6 and DIN EN 10083, high-alloy steels according to DIN EN 10088, and filler materials for steel welding according to DIN EN ISO 2560. The systematics of the ''law of cohabitation'' was applied to welding engineering for the first time here. (orig.) [German] Das in vierter Auflage erscheinende Buch widmet sich der Schweissmetallurgie mit ihren Besonderheiten. Die vielfaeltigen Probleme der Eisenwerkstoffe und der nichteisenmetallischen Werkstoffe bei ihrer schweisstechnischen Verarbeitung werden ausfuehrlich dargestellt. Um Korrosionsschaeden an geschweissten Konstruktionen vorzubeugen, wird die Metallurgie aller technisch bedeutsamen Werkstoffe, wie unlegierte und legierte Staehle, Eisen-Gusswerkstoffe, die wichtigsten NE-Metalle, ausfuehrlich besprochen. An den Kapitelenden findet der interessierte Leser Aufgaben, von denen ein

  3. Un modelo de sistema dinámico híbrido utilizando el enfoque de la lógica difusa

    Directory of Open Access Journals (Sweden)

    Germán García Benítez

    2010-01-01

    Full Text Available Se presenta un modelo de sistema dinámico híbrido utilizando la lógica difusa. Para lograr esto se hace una breve descripción de los principales enfoques que se tienen en la actualidad de los sistemas dinámicos híbridos desarrollando las ecuaciones básicas de los bloques que conforman el modelo. Actualmente la teoría del control se ha centrado en el estudio por separado de la dinámica continua y la dinámica discreta; sin embargo, es necesario introducir el estudio de la combinación de ambos en un solo tratado. En el ámbito industrial los procesos son dinámicos y toda su estructura de control está basada en la teoría de la lógica digital. Sin embargo existe el paradigma de la lógica difusa, la cual se introduce en este artículo para proponer un nuevo enfoque. Cabe mencionar que para validar el modelo se utilizan herramientas computacionales de simulación de sistemas dinámicos.

  4. Redemption of asthma pharmaceuticals among stainless steel and mild steel welders

    DEFF Research Database (Denmark)

    Kristiansen, Pernille; Jørgensen, Kristian Tore; Hansen, Johnni

    2015-01-01

    PURPOSE: The purpose was to examine bronchial asthma according to cumulative exposure to fume particulates conferred by stainless steel and mild steel welding through a proxy of redeemed prescribed asthma pharmaceuticals. METHODS: A Danish national company-based historical cohort of 5,303 male ever...... was estimated by combining questionnaire data on welding work with a welding exposure matrix. The estimated exposure accounted for calendar time, welding intermittence, type of steel, welding methods, local exhaustion and welding in confined spaces. Hazard ratios (HRs) with 95 % confidence intervals (CIs) were...... nonsignificant increased rate of redemption of asthma medicine was observed among high-level exposed stainless steel welders in comparison with low-level exposed welders (HR 1.54, 95 % CI 0.76-3.13). This risk increase was driven by an increase risk among non-smoking stainless steel welders (HR 1.46, 95 % CI 1...

  5. Steel. A handbook for materials research and engineering. Vol. 1. Fundamentals

    Energy Technology Data Exchange (ETDEWEB)

    1992-01-01

    This STEEL Textbook is the outcome of reflections within the Materials Committee of the German Iron and Steel Institute on whether to republish the Manual of Special Steels, the highly commendable work by E. Houdremont. Discussions came to the conclusion, however, that for various reasons it was neither possible nor expedient simply to publish a follow-up edition of the famed Houdremont. To begin with and from today's vantage point, there no longer seemed to be any justification for restricting the work to special steels in the sense of the term as understood by E. Houdremont. The term ''special steel'' has never gained acceptance in official circles or standards. If we replace it by the term ''high-grade steel'', which is nowadays defined in standards, and this would appear permissible with certain qualifications, and if we bear in mind that the boundaries between high-grade steels and non-high-grade steels, the commercial and quality steels, although defined in standards (see part A), nonetheless in terms of engineering parameters are quite blurred, so it would seem only fitting for such as work to cover all the various grades of steel, also in view of the great significance of the non-high-grade steels. Because of the very many different grades of steel, this approach necessarily involves the collaboration of very many experts, in other words it entails a joint effort. Moreover, the vast, barely manageable quantity of literature in this field all of which can hardly be analysed by just one person, inevitably leads to the conclusion that there is a need to produce the new work as a joint effort. (orig.).

  6. Aluminium-rich coatings as tritium permeation barriers on MANET (1.4914) stainless steel

    International Nuclear Information System (INIS)

    Terlain, A.; De Vito, E.

    1994-01-01

    Al-rich coatings on 1.4914 martensitic steel, produced by different techniques, have been investigated with optical and scanning electron microscopy, X-ray fluorescence and X-ray photoelectron spectroscopy. Tests for their Pb-17Li compatibility and thermo cycling behaviours have been performed on some coated specimens. Up to now, none of the investigated coatings can be eliminated on the basis of the tests and analyses performed. Further work is required to adapt 1.4914 steel coating techniques to fusion reactor requirements. (author) 9 refs.; 5 figs.; 1 tab

  7. [Factors influencing electrocardiogram results in workers exposed to noise in steel-making and steel-rolling workshops of an iron and steel plant].

    Science.gov (United States)

    Li, Y H; Yu, S F; Gu, G Z; Chen, G S; Zhou, W H; Wu, H; Jiao, J

    2016-02-20

    To investigate the factors influencing the electrocardiogram results in the workers exposed to noise in steel-making and steel rolling workshops of an iron and steel plant. From September to December, 2013, cluster sampling was used to select 3 150 workers exposed to noise in the steel-making and steel-rolling workshops of an iron and steel plant, and a questionnaire survey and physical examinations were performed. The number of valid workers was 2 915, consisting of 1 606 workers in the steel-rolling workshop and 1 309 in the steel-making workshop. The electrocardiogram results of the workers in steel-making and steel-rolling workshops were analyzed. The overall abnormal rate of electrocardiogram was 26.35%, and the workers in the steel-making workshop had a significantly higher abnormal rate of electrocardiogram than those in the steel-rolling workshop(32.24% vs 21.54%, Pelectrocardiogram than female workers(27.59% vs 18.61%, Pelectrocardiogram than those who did not drink(28.17% vs 23.75%, Pelectrocardiogram than those who were not exposed to high temperature(29.43% vs 20.14%, Pelectrocardiogram in the workers with cumulative noise exposure levels of electrocardiogram results. High cumulative noise exposure, alcohol consumption, and high temperature may affect the abnormal rate of electrocardiogram in the workers exposed to noise in steel-making and steel-rolling workshops.

  8. Nuevos modelos de redes de neuronas artificiales para simulación y control desistemas dinámicos

    OpenAIRE

    Galván León, Inés María

    1997-01-01

    Uno de los principales problemas en el campo de los procesos dinámicos es el control de su comportamiento, control que es necesario para que la evolución del proceso se lleve a cabo en una dirección y con una cierta dinámica deseada. Esto puede traducirse en mantener una condición estable, seguir una trayectoria especificada o alcanzar una determinada meta. Para ello es necesario incluir un sistema de control, el cual influye en la dinámica del proceso, regulando su comportamiento. La teoría...

  9. 1x2M steel performance in the BOR-60 steam generator

    International Nuclear Information System (INIS)

    Golovanov, V.N.; Shamardin, V.K.; Kondratiev, V.I.; Kryukov, F.N.; Chernobrovkin, Yu.V.; Bulanova, T.M.; Bai, V.F.

    The results from studies of 1x2M steel characteristics are presented. This steel was used as the material for the BOR-60 steam generator that had been in operation under the steam generating mode for 18,000 hs (35,000 hs in sodium). It was revealed that the pit corrosion depth on the water/steam side evaporative tube surfaces was about 0.25 μm and less and the total corrosion rate was less than 0.06 mm/y. The mechanical properties of the material were essentially similar both in the evaporator and superheater and met all the requirements imposed on. Based on the analysis of data on the decarbonizaton depth in sodium and on the corrosion damage in water and steam it was concluded that 1x2M steel can be successfully used as the steam generator material at the operating temperatures up to 470 deg. C and had sufficiently longer service-life as compared to 18,000 hs. (author)

  10. [Ernst Rüdin--a Swiss psychiatrist as the leader of Nazi psychiatry--the final solution as a goal].

    Science.gov (United States)

    Peters, U H

    1996-09-01

    The study of work and life of the Swiss-German psychiatrist Ernst Rüdin, honoured up to our time as "father of psychiatric genealogy", lead to different views. Rüdin early in his life became a racial fanatic, and as a propagandist for the purity of the "Germanic people" he constantly demanded preventive coercive measures against the reproduction of the mentally ill and other, in the racist's view, undesirable persons. With this objective in mind he started his psychiatric research. The results of Rüdin's monograph about the genetics of dementia precox do not withstand scientific criticism but confirmed his preexisting opinions. They served however as scientific reasoning for the forced sterilisation by the Nazis, for which Rüdin's comments were obligatory. The next step, to the holocaust of the mentally ill and the undesirable, was not only tacitly agreed with by Rüdin. Max Weber, Karl Jaspers and others realised at an early time the dangers arising from racial hygienics and voiced their warnings in a plain language. The surviving victims are still waiting for compensation.

  11. [Automated measurement of distance vision based on the DIN strategy].

    Science.gov (United States)

    Effert, R; Steinmetz, H; Jansen, W; Rau, G; Reim, M

    1989-07-01

    A method for automated measurement of far vision is described which meets the test requirements laid down in the new DIN standards. The subject sits 5 m from a high-resolution monitor on which either Landolt rings or Snellen's types are generated by a computer. By moving a joystick the subject indicates to the computer whether he can see the critical detail (e.g., the direction of opening of the Landolt ring). Depending on the subject's input and the course of the test so far, the computer generates the next test symbol until the threshold criterion is reached. The sequence of presentation of the symbols and the threshold criterion are also in accordance with the DIN standard. Initial measurements of far vision using this automated system produced similar results to those obtained by conventional methods.

  12. Insuficiencia dinámica, crecimiento y desempleo en México, 1974-2012

    OpenAIRE

    Blanca L. Avendaño Vargas; Ignacio Perrotini Hernández

    2015-01-01

    El artículo presenta una reformulación de la hipótesis de insuficiencia dinámica de Prebisch (1970), analiza la teoría dinámica de Harrod (1939), la ley Kaldor-Verdoorn (Kaldor, 1966; 1967) y la teoría del crecimiento endógeno de Thirlwall (1969; 2000). A posterioriestudiamos los determinantes del crecimiento económico y del desempleo en México durante el periodo 1974-2012. Con base en el análisis empírico, sostenemos que una baja tasa de acumulación genera una reducida absorción de empleo, u...

  13. Dinámica de sistemas en la gestión de inventarios

    OpenAIRE

    Daniel Alejandro Agudelo Serna; Yohana Marcela López Rivera

    2018-01-01

    En el presente artículo se estudia el proceso de gestión de inventarios por medio de la dinámica de sistemas, como herramienta metodológica que permite conocer el comportamiento de las variables de acuerdo a sus relaciones y a las decisiones que se tomen teniendo en cuenta su causalidad y realimentación. El desarrollo del documento está determinado por una revisión de conceptos teóricos relacionados con la gestión de inventarios y dinámica de sistemas, seguido por una revisión de lit...

  14. Effect of normalization heat treatment on creep and tensile properties of modified 9Cr-1Mo steel

    International Nuclear Information System (INIS)

    Panneer Selvi, S.; Sakthivel, T.; Parameswaran, P.; Laha, K.

    2016-01-01

    Creep and tensile properties have been investigated on modified 9Cr-1Mo steel subjected to single and double normalization heat treatments. Optical, scanning and transmission electron microscopic investigation revealed the presence of refined prior austenite grain size and fine M 23 C 6 precipitates in the double normalized steel compared to the steel subjected to single normalization heat treatment. Increased creep strain and significant reduction in creep rupture life were observed with the double normalized steel in comparison with single normalized steel. Increased tensile ductility coupled with marginal decrease in tensile strength at higher test temperature was observed with double normalized steel compared to single normalized steel. It has been attributed to the presence of refined prior austenite grain size and coarsening of Nb rich MX precipitates in double normalized steel. (author)

  15. Dinámica migratoria... ¿hibridación cultural u homologación global?

    Directory of Open Access Journals (Sweden)

    Claudia Carolina Zamorano Villarreal

    2014-01-01

    Full Text Available Ante la consolidación del modelo de subcontratación en México asistimos a una nueva cultura laboral ¿Qué cambios ha impulsado este modelo en las prácticas de la pobla - ción y su cultura? Analizando la relación entre el modo de producción flexible de la maquila y la dinámica de migración propia a las ciudades de la frontera norte de Mé - xico, se muestra que la maquiladora respetó y aprovechó está dinámica para reducir o aumentar el número de trabajadores, según lo requiriera la producción flexible. Pero, desde mediados de los años noventa, empezó a transformar estás dinámicas y con ellas, la cultura de sus trabajadores.

  16. Creep behaviour of modified 9Cr-1Mo ferritic steel

    International Nuclear Information System (INIS)

    Choudhary, B.K.; Isaac Samuel, E.

    2011-01-01

    Creep deformation and fracture behaviour of indigenously developed modified 9Cr-1Mo steel for steam generator (SG) tube application has been examined at 823, 848 and 873 K. Creep tests were performed on flat creep specimens machined from normalised and tempered SG tubes at stresses ranging from 125 to 275 MPa. The stress dependence of minimum creep rate obeyed Norton's power law. Similarly, the rupture life dependence on stress obeyed a power law. The fracture mode remained transgranular at all test conditions examined. The analysis of creep data indicated that the steel obey Monkman-Grant and modified Monkman-Grant relationships and display high creep damage tolerance factor. The tertiary creep was examined in terms of the variations of time to onset of tertiary creep with rupture life, and a recently proposed concept of time to reach Monkman-Grant ductility, and its relationship with rupture life that depends only on damage tolerance factor. SG tube steel exhibited creep-rupture strength comparable to those reported in literature and specified in the nuclear design code RCC-MR.

  17. Passive behaviour of alloy corrosion-resistant steel Cr10Mo1 in simulating concrete pore solutions with different pH

    International Nuclear Information System (INIS)

    Ai, Zhiyong; Jiang, Jinyang; Sun, Wei; Song, Dan; Ma, Han; Zhang, Jianchun; Wang, Danqian

    2016-01-01

    Highlights: • A new alloy corrosion-resistant steel Cr10Mo1 is developed for reinforcing rebar of concrete in severe environments. • The effects of pH on the passive behaviour of Cr10Mo1 steel compared with plain carbon steel were studied systematically by electrochemical techniques and surface analysis. • The mechanism for self-reinforcing passivity against carbonation of the corrosion-resistant steel is revealed. - Abstract: The passive behaviour of new alloy corrosion-resistant steel Cr10Mo1 and plain carbon steel (as a comparison) in simulating concrete pore solutions of different pH (ranging from 13.5 to 9.0) under open circuit potential conditions, was evaluated by various electrochemical techniques: potentiodynamic polarization, capacitance measurements and electrochemical impedance spectroscopy. The chemical composition and structure of passive films were investigated by X-ray photoelectron spectroscopy (XPS) and secondary ion mass spectroscopy (SIMS). The electrochemical responses of passive films show that Cr10Mo1 steel has an increasing passivity with pH decreasing while carbon steel dose conversely, revealing carbonation does no negative effect on passivation of the corrosion-resistant steel. SIMS reveals that the passive film on the corrosion-resistant steel presents a bilayer structure: an outer layer mainly consisting of Fe oxides and hydroxides, and an inner layer enriched in Cr species, while only a Fe-concentrated layer for carbon steel. According to the XPS analysis results, as the pH decreases, more stable and protective Cr oxides are enriched in the film on Cr10Mo1 steel while Fe oxides gradually decompose. Higher content of Cr oxides in the film layer provides Cr10Mo1 corrosion-resistant steel more excellent passivity at lower pH.

  18. Passive behaviour of alloy corrosion-resistant steel Cr10Mo1 in simulating concrete pore solutions with different pH

    Energy Technology Data Exchange (ETDEWEB)

    Ai, Zhiyong, E-mail: 230139452@seu.edu.cn [School of Materials Science and Engineering, Southeast University, Nanjing 211189, Jiangsu (China); Jiangsu Key Laboratory of Construction Materials, Nanjing 211189, Jiangsu (China); Jiang, Jinyang, E-mail: jiangjinyang16@163.com [School of Materials Science and Engineering, Southeast University, Nanjing 211189, Jiangsu (China); Jiangsu Key Laboratory of Construction Materials, Nanjing 211189, Jiangsu (China); Sun, Wei, E-mail: sunwei@seu.edu.cn [School of Materials Science and Engineering, Southeast University, Nanjing 211189, Jiangsu (China); Jiangsu Key Laboratory of Construction Materials, Nanjing 211189, Jiangsu (China); Song, Dan, E-mail: songdancharls@hhu.edu.cn [School of Materials Science and Engineering, Southeast University, Nanjing 211189, Jiangsu (China); Jiangsu Key Laboratory of Construction Materials, Nanjing 211189, Jiangsu (China); College of Mechanics and Materials, Hohai University, Nanjing 210098, Jiangsu (China); Ma, Han, E-mail: mahan-iris@shasteel.cn [Research Institute of Jiangsu Shasteel Iron and Steel, Zhangjiagang 215625, Jiangsu (China); Zhang, Jianchun, E-mail: Zhangjc-iris@shasteel.cn [Research Institute of Jiangsu Shasteel Iron and Steel, Zhangjiagang 215625, Jiangsu (China); Wang, Danqian, E-mail: wonderbaba@126.com [School of Materials Science and Engineering, Southeast University, Nanjing 211189, Jiangsu (China); Jiangsu Key Laboratory of Construction Materials, Nanjing 211189, Jiangsu (China)

    2016-12-15

    Highlights: • A new alloy corrosion-resistant steel Cr10Mo1 is developed for reinforcing rebar of concrete in severe environments. • The effects of pH on the passive behaviour of Cr10Mo1 steel compared with plain carbon steel were studied systematically by electrochemical techniques and surface analysis. • The mechanism for self-reinforcing passivity against carbonation of the corrosion-resistant steel is revealed. - Abstract: The passive behaviour of new alloy corrosion-resistant steel Cr10Mo1 and plain carbon steel (as a comparison) in simulating concrete pore solutions of different pH (ranging from 13.5 to 9.0) under open circuit potential conditions, was evaluated by various electrochemical techniques: potentiodynamic polarization, capacitance measurements and electrochemical impedance spectroscopy. The chemical composition and structure of passive films were investigated by X-ray photoelectron spectroscopy (XPS) and secondary ion mass spectroscopy (SIMS). The electrochemical responses of passive films show that Cr10Mo1 steel has an increasing passivity with pH decreasing while carbon steel dose conversely, revealing carbonation does no negative effect on passivation of the corrosion-resistant steel. SIMS reveals that the passive film on the corrosion-resistant steel presents a bilayer structure: an outer layer mainly consisting of Fe oxides and hydroxides, and an inner layer enriched in Cr species, while only a Fe-concentrated layer for carbon steel. According to the XPS analysis results, as the pH decreases, more stable and protective Cr oxides are enriched in the film on Cr10Mo1 steel while Fe oxides gradually decompose. Higher content of Cr oxides in the film layer provides Cr10Mo1 corrosion-resistant steel more excellent passivity at lower pH.

  19. Effect of melting technique on grain size and heat resistance of the 12Kh1MF steel

    International Nuclear Information System (INIS)

    Lanskaya, K.A.; Kulikova, L.V.; Butneva, N.I.

    1978-01-01

    Investigated are the 12Kh1MF steel melted in open-hearth and arc furnaces (deoxidation by aluminium in 1.0 kg/t quantity) and then subjected to electroslag melting. The size of an austenitic grain depends on the residual contents of nitrogen and aluminium in steel. The open-hearth metal subjected to electroslag melting and containing a small quantity of nitrogen (0.006%) and aluminium (0.013%) has coarse austenitic grains and higher heat resistance compared to the steel melted in an arc furnace and also sub ected to electroslag melting. The nitride analysis of steel is carried out

  20. The Injection of Sodium into Liquid Stainless Steel: A Report of the Second Experimental Na - SS/1

    International Nuclear Information System (INIS)

    Abbey, M.J.; Asher, R.C.; Bradshaw, L.; Davies, D.; Sangwinw, S.J.

    1976-01-01

    A second experiment in which liquid sodium was injected beneath the surface of molten steel has been carried out using an experimental technique based on that described in AERE - M 2770 but incorporating several improvements particularly in the instrumentation. The sodium (∼1.5 g) was at 400-450 deg. C and the steel (stainless steel in this instance) was at 1750-1800 deg. C. A vapour explosion occurred after a measured dwell time and two force pulses >100 N and 60 N, separated by an interval of ∼1 ms were transmitted to the base of the crucible containing the molten steel. Most of the sodium vapourised' but only a minor part of the steel was converted into small particles. In conclusion: A vapour explosion occurred when ∼1.5 g of sodium at 400-450 deg. C was injected 1.5 cm beneath the surface of molten stainless steel at 1750-1800 deg. C. The explosion occurred 100 N and the second one ∼60 N compared with one pulse of ∼600 N measured in Na/CS/1. Both pulses had a base width of ∼1 ms and the second one a pulse width of ∼500 μs. There was no indication of the prolonged series of pulses observed in Na-CS/1 and which may have been a feature of the equipment used. Virtually all the sodium was vaporised whereas in the previous experiment much of the sodium was recovered as droplets. The steel temperature was > 200 deg. C higher. The steel was on the whole not so finely dispersed; only ∼2% was less than ∼0.5 mm diameter compared with ∼10% in Na-CS/1. Future experiments of this type could be further instrumented; in particular it would be desirable to measure the exact injection rate for each sodium injection and to measure pressure pulses at other points of the equipment

  1. Creep-fatigue evaluation method for modified 9Cr-1Mo steel

    International Nuclear Information System (INIS)

    Wada, Y.; Aoto, K.

    1997-01-01

    As creep-fatigue evaluation methods on normalized and tempered Modified 9Cr-1Mo steel for design use, the time fraction rule and the simplified conventional ductility exhaustion rule are investigated for the prediction of tension strain hold creep-fatigue damage of this material. For the above investigation, stress relaxation behaviour during strain hold has to be analyzed using stress-strain-time relation. The initial value of stress relaxation was determined by cyclic stress-strain curves in continuous cycling fatigue tests. Cyclic stress-strain behaviour of Mod.9Cr-1Mo(NT) steel is different from that of austenitic stainless steels, so this effect was considered. Stress relaxation analysis was performed using static creep strain-time relation and conventional hardening rule. The time fraction by using the above stress relaxation analysis results can give good prediction for creep-fatigue life of Mod.9Cr-1Mo(NT) steel. For design use it is practical to be able to estimate creep damages conservatively by both strain behaviour of cyclic plastic (in continuous cycling fatigue tests) and monotonic creep (in standard creep tests). The life reduction by strain hold at the minimum peak of compressive stress in creep-fatigue tests was examined, and this effects can be evaluated by the relationship between the location of oxidation and the effective deformation at crack tip. In an accelerated oxidation environment, for example in high temperature and high pressure steam, a different approach for life reduction should be developed based on the mechanism of growth of oxide and crack growth with oxidation. However, in the creep damage dominant region, its effect is saturated and the effect of cavity growth along grain boundary becomes dominant for long-term strain hold in the high temperature conditions. (author). 6 refs, 6 figs

  2. Tensile properties of modified 9Cr-1Mo steel by shear punch testing and correlation with microstructures

    Energy Technology Data Exchange (ETDEWEB)

    Karthik, V., E-mail: karthik@igcar.gov.in [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam, Tamil Nadu 603102 (India); Laha, K.; Parameswaran, P.; Chandravathi, K.S.; Kasiviswanathan, K.V.; Jayakumar, T.; Raj, Baldev [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam, Tamil Nadu 603102 (India)

    2011-10-15

    Modified 9Cr-1Mo ferritic steel (P91) is subjected to a series of heat treatments consisting of soaking for 5 min at the selected temperatures in the range 973 K-1623 K (below Ac{sub 1} to above Ac{sub 4}) followed by oil quenching and tempering at 1033 K for 1 h to obtain different microstructural conditions. The tensile properties of the different microstructural conditions are evaluated from small volumes of material by shear punch test technique. A new methodology for evaluating yield strength, ultimate tensile strength and strain hardening exponent from shear punch test by using correlation equations without employing empirical constants is presented and validated. The changes in the tensile properties are related to the microstructural changes of the steel investigated by electron microscopic studies. The steel exhibits minimum strength and hardness when soaked between Ac{sub 1} and Ac{sub 3} (intercritical range) temperatures due to the replacement of original lath martensitic structure with subgrains. The finer martensitic microstructure produced in the steel after soaking at temperatures above Ac{sub 3} leads to a monotonic increase in hardness and strength with decreasing strain hardening exponent. For soaking temperatures above Ac{sub 4}, the hardness and strength of the steel increases marginally due to the formation of soft {delta} ferrite. - Highlights: > A methodology presented for computing tensile properties from shear punch test. > UTS and strain hardening estimated using extended analysis of blanking models. > The analysis methodology validated for different heat treated 9Cr-1Mo steel. > Changes in tensile properties of steel correlated with microstructures.

  3. Requirements on cast steel for the primary coolant circuit of water cooled reactors

    International Nuclear Information System (INIS)

    The most important requirements placed on the structural components of water cooled nuclear reactors include corrosion resistance and mechanical materials properties. Intercrystalline corrosion resistance was tested using the Strauss Test in compliance with the DIN 50914 Standard. Following sensitization between 600 to 700 degC with a dwell time between 15 minutes and 100 hours, a specimen homogeneously annealed with the casting and rapidly water cooled showed no intercrystalline corrosion. Specimens cooled from 1050 degC at a rate of 100 degC per hour showed no unambiguous tendency for intercrystalline corrosion after sensitization; in some cases, however, an initial attack of intercrystalline corrosion was found. It was found that austenitic Cr-Ni cast steel containing 2.5% Mo and about 15% ferrite showed the sensitive intercrystalline corrosion range at higher temperatures and longer dwell times than rolled Cr-Ni steels. In plating the ferritic cast steel with a corrosion resistant plating material, annealing temperature after welding must not exceed 600 to 620 degC otherwise the resistance of the plated layer against intercrystalline corrosion would not be safeguarded, and following annealing for stress removal at a temperature of 600 to 620 degC all requirements must be satisfied by the weld metal and weld transition placed on the initial material. Martensite materials are used for the manufacture of components which are not used under pressure, such as alloys with 13% Cr and 1% to 6% Ni and alloys with 17% Cr and 4% Ni. Carbon content is maintained below 0.10% to guarantee good weldability and the highest corrosion resistance. Cast steels with 13% Cr and 4% Ni after a dwell of 2500 hours in fully desalinated water without oxygen and with 3600 ppm of boron at a test temperature of 95 to 300 degC showed a surface reduction of 0.005 mm annually. In identical conditions except for the water containing oxygen the reduction in surface was 0.05 mm per year. (J.B.)

  4. Comparative study of the differences between dynamic and normal strategies with Octopus 1-2-3 Estudo comparativo das diferenças entre as estratégias dinâmica e normal com o perímetro Octopus 1-2-3

    Directory of Open Access Journals (Sweden)

    R. M. O. Santos

    1999-12-01

    Full Text Available Purpose: To show the results of a comparative study between dynamic and normal strategies with Octopus 1-2-3. Methods: Automatic perimetry using the Octopus 1-2-3 with dynamic and normal strategies was performed on 24 glaucomatous patients (eight males and 16 females within an average interval of six months between the two exams. All patients had previously submitted to at least one automatic perimetry with the Octopus 1-2-3. The data compared, for both eyes, were: the patient's age, number of questions, mean sensitivity (MS, mean defect (MD, loss variance (LV, short-term fluctuation (SF and the reliability factor (RF. In the statistical analyses through the paired t test, only the visual fields with RF less than 10 were included. The level of significance was equal to 5% (p Objetivo: Analisar os resultados de um estudo comparativo entre as estratégias dinâmica e normal utilizando o perí-metro Octopus 1-2-3. Métodos: Utilizando o Octopus 1-2-3 nas estratégias dinâmica e normal foi realizada a perimetria automatizada em 24 pacientes glaucomatosos (8 homens e 16 mulheres com uma média de intervalo entre os 2 exames de 6 meses. Todos pacientes já haviam sido previamente submetidos a pelo menos um exame de perimetria automatizada no Octopus 1-2-3. Os dados comparados, para ambos os olhos, foram: a idade do paciente, número de estímulos, sensibilidade média (MS, defeito médio (MD, perda localizada (LV, flutuação em curto prazo (SF e o fator de confiabilidade (RF. Na análise estatística, utilizando o teste t pareado, somente os campos visuais com RF menor que 10 foram incluídos. O nível de significância foi igual a 5% (p < 0,05. Resultados: Não houve diferença estatisticamente significativa entre as duas estratégias em relação à idade, LV, SF e RF. Entretanto, houve diferença estatisticamente significativa na duração do teste, número de estímulos, MS e MD. A estratégia dinâmica mostrou uma sensibilidade difusa maior e

  5. Estabilizações lombares dinâmicas Estabilizaciones lumbares dinámicas Lumbar dynamic stabilizations

    Directory of Open Access Journals (Sweden)

    Ivan Dias Rocha

    2012-01-01

    Full Text Available O funcionamento fisiológico normal da coluna depende da movimentação normal de cada unidade motora, que consiste em duas vértebras e o disco intervertebral interposto entre elas. Embora a artrodese da coluna vertebral venha sendo utilizada para o tratamento de diversas doenças da coluna, essa modalidade de tratamento acarreta a perda de movimentação dos níveis em que houve a fusão e como consequência pode sobrecarregar os níveis adjacentes podendo provocar a sua degeneração precoce. Proponentes das técnicas de estabilização dinâmicas acreditam que estas podem levar a correção dos problemas minimizando o risco de degeneração dos níveis adjacentes. Atualmente existem no mercado diversos métodos de estabilização dinâmica anteriores e posteriores. Já existem trabalhos biomecânicos que comprovam o benefício teórico de quase todos eles, porém ainda hoje, faltam ensaios clínicos que comprovem a sua utilidade e segurança por longos períodos de seguimento para o paciente. Portanto é fundamental que estes materiais sejam analisados de maneira acadêmica para que no futuro próximo possam ser utilizados em situações precisas e com segurança para os pacientes.El funcionamiento fisiológico normal de la columna depende de los movimientos normales de cada unidad motora, la cual consiste de dos vértebras y del disco intervertebral interpuesto entre ellas. Aunque la artrodesis de la columna vertebral está siendo utilizada para el tratamiento de diversas enfermedades de la columna, esa modalidad de tratamiento causa la pérdida de los movimientos en los niveles en los que hubo la fusión y, como consecuencia, puede sobrecargar los niveles adyacentes, pudiendo provocar su degeneración precoz. Los proponentes de las técnicas de estabilización dinámica creen que éstas pueden llevar a la corrección de los problemas, minimizando el riesgo de degeneración de los niveles adyacentes. Actualmente, existen en el mercado

  6. Evaluation of dynamic fracture toughness of cold worked 9Cr-1Mo steel

    International Nuclear Information System (INIS)

    Sathyanarayanan, S.; Sasikala, G.; Ray, S.K.

    2004-01-01

    Dynamic J-R curves for cold worked 9Cr-1Mo steel have been estimated from instrumented impact test data at ambient temperature on pre-cracked Charpy specimens using three methods of analysis, namely those by Ray et al., Schindler, and Sreenivasan and Mannan. It is concluded that of these three, Schindler's method is the best suited for the purpose since it gives consistent variations with cold work of dynamic J-R curves and dynamic fracture toughness. Cold work results in substantial degradation in dynamic fracture toughness of 9Cr-1Mo steel

  7. On the measurement of the stacking-fault energies of face centered cubic metal and austenitic stainless steels by X-ray diffraction

    International Nuclear Information System (INIS)

    Borges, J.F.A.

    1985-01-01

    An X-rays diffraction method was applied to measure the Stacking-Fault Energies (SFE) of the AISI 304, AISI 316, AISI 347 and DIN-WERKSTOFF 1.4970 Austenitic Stainless Steels. The SFE determination plays an important role in the research of the mechanical behaviour of the Metal and Alloys, their deformation mechanisms, stability of microstructure amd electronic configuration. The method is based on the relationship between the SFE and the ratio of the Mean Square Strain to the Stacking-Fault probability. The Mean Square Strain was evaluated by Fourier Analysis of X-rays Diffraction profiles, corrected to reduce instrumental effects, followed by the application of the Warren-Averbach method to the Fourier Coefficients. The Stacking-Fault probabilities were derived from the changes of peak separations between cold-worked and annealed specimens. (author) [pt

  8. Sistemas dinámicos en la interacción emocional madre-hijo: primera fase

    Directory of Open Access Journals (Sweden)

    Jaime Castro Martínez

    2013-03-01

    Full Text Available Los avances en psicología de las emociones y psicología del desarrollo han exigido nuevos cambios tanto de orden teórico como metodológico para describir y explicar la variabilidad de las res-puestas infantiles a los cambios que tienen lugar en la dinámica socio-emocional con la madre. Producto de estas variaciones, aparece la integración de los sistemas dinámicos a las descrip- ciones de los teóricos del desarrollo emocional bajo supuestos psicobiológicos y sociobiológicos. Esta investigación indaga el posible uso de modelos de sistemas dinámicos en la generación de patrones de organización durante la interrelación socio- emocional madre-hijo, bajo cambios en los estados emocionales de la madre y bajo modificaciones debidas al desarrollo infantil. Los hallazgos de esta primera fase muestran algunas diferencias en las dinámicas socio-emocionales en cada uno de los estados emocionales maternos, al igual que regu- laridades en la variación por estado emocional. La investigación sugiere ampliar el marco teórico hacia modelos de componentes emocionales y modelos neurobiológicos, y la inclusión de modelos matemáticos de predicción y de análisis de series de tiempos.

  9. Characterizing microstructural changes in ferritic steels by positron annihilation spectroscopy: Studies on modified 9Cr-1Mo steel

    Energy Technology Data Exchange (ETDEWEB)

    Hari Babu, S., E-mail: shb@igcar.gov.in [Materials Science Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102, TN (India); Rajkumar, K.V. [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102, TN (India); Hussain, S. [UGC-DAE CSR, Kokilamedu 603 104, TN (India); Amarendra, G.; Sundar, C.S. [Materials Science Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102, TN (India); Jayakumar, T. [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102, TN (India)

    2013-01-15

    Highlights: Black-Right-Pointing-Pointer Positron lifetime technique probing microstructure of ferritic/martensitic steels. Black-Right-Pointing-Pointer Correlation between positron lifetime, ultrasonic and hardness. Black-Right-Pointing-Pointer Complementary nature of positron annihilation spectroscopy in probing defects. Black-Right-Pointing-Pointer Distinguishing precipitation stages by positron annihilation spectroscopy. - Abstract: Applicability of positron annihilation spectroscopy in probing the microstructural changes in ferritic steels has been investigated with thermal treatment studies on modified 9Cr-1Mo steel, during 300-1273 K. Positron lifetime results are compared with those of ultrasonic velocity and hardness techniques with two initial microstructural conditions i.e., normalized and tempered condition as well as only normalized condition. In first case, positron lifetime is found to be sensitive to small changes in metal carbide precipitation which could not be probed by other two techniques. In later case, positron lifetime is found to be sensitive to defect annealing until 673 K and in distinguishing the growth and coarsening of metal carbide precipitation stages during 773-1073 K. The present study suggests that by combining positron lifetime, ultrasonic velocity and hardness measurements, it is possible to distinguish distinct microstructures occurring at different stages.

  10. Gauge fields with respect to d = (3+1) in the Kaluza-Klein theories and in the spin-charge-family theory

    Energy Technology Data Exchange (ETDEWEB)

    Lukman, Dragan; Mankoc Borstnik, Norma Susana [University of Ljubljana, Department of Physics, FMF, Ljubljana (Slovenia)

    2017-04-15

    It is shown that in the spin-charge-family theory (Mankoc Borstnik in arXiv:1607.01618v2, 2016, Phys Rev D 91:065004. arxiv:1409.7791, 2015, J Mod Phys 6:2244. doi:10.4236/jmp.2015.615230. arXiv: 1409.4981, 2015, J Mod Phys 4:823. doi:10.4236/jmp.2013.46113. arxiv:1312.1542, 2013, arxiv:1409.4981, 2014) as well as in all the Kaluza-Klein like theories (Blagojevic in Gravitation and gauge symmetries, IoP Publishing, Bristol, 2002, An introduction to Kaluza-Klein theories, World Scientific, Singapore, 1983), vielbeins and spin connections manifest in d = (3+1) space equivalent vector gauge fields, when space with d ≥ 5 has a large enough symmetry. The authors demonstrate this equivalence in spaces with the symmetry of the metric tensor in the space out of d = (3+1)-g{sup στ} = η{sup στ} f{sup 2} - for any scalar function f of the coordinates x{sup σ}, where x{sup σ} denotes the coordinates of space out of d = (3+1). Also the connection between vielbeins and scalar gauge fields in d = (3+1) (offering the explanation for the Higgs scalar) is discussed. (orig.)

  11. Creep Rupture Analysis and Life Estimation of 1.25Cr-0.5Mo, 2.25Cr-1Mo and Modified 9Cr-1Mo Steel: A Comparative Study

    Science.gov (United States)

    Roy, Prabir Kumar

    2018-04-01

    This paper highlights a comparative assessment of creep life of 1.25Cr-0.5Mo, 2.25Cr-1Mo and modified 9Cr-1Mo steels based on accelerated creep rupture tests. Creep rupture test data have been analysed and creep life of the above mentioned materials have been assessed using Larson Miller parameter at the stress levels of 60 and 42 MPa for different temperatures. Limiting steam temperatures for minimum design life of 105 h at 42 and 60 MPa for the above mentioned steels have also been calculated. Microstructural studies for the three above mentioned steels are also done.

  12. “We’re Still in a Struggle”: Diné Resilience, Survival, Historical Trauma, and Healing

    OpenAIRE

    Goodkind, Jessica R.; Hess, Julia Meredith; Gorman, Beverly; Parker, Danielle P.

    2012-01-01

    As part of a community/university collaborative effort to promote the mental health and well-being of Diné (Navajo) youth, we explored the relevance of addressing historical trauma and current structural stressors and of building on individual and community strengths through healing and social transformation at multiple levels. Qualitative analyses of 74 ethnographic interviews with 37 Diné youth, parents, and grandparents suggested that a focus on historical trauma as a conceptual frame for ...

  13. Development of niobium alloy/stainless steel joint by friction welding, (1)

    International Nuclear Information System (INIS)

    Kikuchi, Taiji; Kawamura, Hiroshi.

    1988-08-01

    The niobium alloy and stainless steel have been jointed by the nicrobrazing method generally. However the strength of the jointed part is weaker than that of the mother material. Therefore we developed the niobium alloy(Nb-1 % Zr)/stainless steel(SUS 304) transition joint by the friction welding method. As the tests for the development. We conducted the mechanical tests (tensile test at room temperature, 300 deg C, 500 deg C and 700 deg C, torsion fatigue test and burst test), metallographical observation and electron prove X-ray microanalysis observation. Those tests proved jointed part by the friction welding had enough properties for general uses. (author)

  14. [Reform of the Law DIN EN ISO 9001:2000. Commentary on the new requirements on quality management systems].

    Science.gov (United States)

    Eckert, H; Böhmer, K

    2000-09-01

    Since January this year the German translation of the third draft to the reform of the DIN EN ISO 9000 is available. The draft reveals an approximation to the models of Business Excellence. Most important changes are a far stronger customer orientation, orientation on the processes and resource management. The norms DIN EN ISO 9002 and 9003 have been removed, ISO 8402 has been integrated in the reformed DIN EN ISO 9000. Apart from that the compatibility with other management systems has been improved. It was the aim of the reform to improve the applicability for all types of business, products and services.

  15. Dinámica exportadora de las empresas born global en Colombia

    Directory of Open Access Journals (Sweden)

    Diana Marcela Escandón Barbosa

    2015-11-01

    Full Text Available Este artículo pretende analizar las condiciones principales del mercado exportador de las empresas born global en el caso colombiano, teniendo en cuenta los principales factores del entorno que determinan su dinámica exportadora. Se utiliza la base de datos GEM Colombia del año 2011, para analizar 297 empresas born global colombianas, mediante un análisis descriptivo y la estimación de un modelo de conglomerados bietápico. Los resultados muestran que los cambios tecnológicos, las características sectoriales y la intensidad competitiva son factores determinantes de la dinámica exportadora de las empresas born global en Colombia, y se concluye que los empresarios se adaptan al mercado internacional mejorando continuamente sus productos y procesos.

  16. Verwendung von Kabeln und isolierten Leitungen für Fernmeldeanlagen und Informationsverarbeitungsanlagen; Besondere Richtlinie für selbsttragende Fernmelde-Luftkabel auf Starkstrom-Freileitungen über 1 kV nach DIN 57818/VDE 0818 [VDE-Richtlinie

    CERN Document Server

    Deutsches Institut für Normung. Berlin

    1983-01-01

    Verwendung von Kabeln und isolierten Leitungen für Fernmeldeanlagen und Informationsverarbeitungsanlagen; Besondere Richtlinie für selbsttragende Fernmelde-Luftkabel auf Starkstrom-Freileitungen über 1 kV nach DIN 57818/VDE 0818 [VDE-Richtlinie

  17. Effect of methanol extract of Prosopis juliflora on mild steel corrosion in 1M HCl

    OpenAIRE

    Zulfareen, Nasarullah; Kannan, Kulanthi; Venugopal, Thiruvengadam

    2016-01-01

    The Prosopis juliflora extract was investigated as a corrosion inhibitor for mild steel in 1M HCl using weight loss measurements, potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS). The inhibition efficiency of Prosopis juliflora increases with an increase in inhibitor concentration and temperature. Polarization studies revealed that Prosopis juliflora acts as a mixed type inhibitor for mild steel in 1M HCl. AC impedance indicates that the value of charge transfer ...

  18. IDEEA „DACO-ROMÂNISMULUI” LA ROMÂNII DIN TRANSILVANIA ÎN EPOCA MODERNĂ

    Directory of Open Access Journals (Sweden)

    Radu ROMÎNAŞU

    2017-08-01

    Full Text Available Îndelungata stare de fragmentarism teritorial şi de separatism politic între români a generat o criză a conştiinţelor liderilor din spaţiul românesc, tensiune din care s-a cristalizat ideea „daco-românismului”. Aceasta s-a concretizat prin iniţierea unei lupte naţionale, în special în spaţiul transilvănean, al cărei punct final a fost constituirea unei Românii întregite, rotunda şi adevărata patrie a tuturor românilor, care a reuşit să fixeze, în memoria urmaşilor, fireştile sale contururi geografice la 1 decembrie 1918.Astfel, ideea „daco-românismului” a devenit coşmarul guvernelor maghiare din perioada dualistă, neamul românesc fiind proiectat, potrivit acestei „legi nescrise” de la nivelul mentalului colectiv al elitei româneşti, ca un tot unitar, graniţele artificiale reuşind să despartă persoane, dar nu şi simţămintele sufleteşti fireşti.Esenţială şi necesară pentru transformarea vechii idei a „daco-românismului” în principiu politic-cultural a fost sinteza cultural-naţională a românilor din monarhia austro-ungară şi a celor din Vechiul Regat, care a pregătit conştiinţele pentru actul istoric de la 1 decembrie 1918.„Daco-românismul” a avut marele merit de a fi chemat la reflexie angajată în jurul unor idei majore, precum: „istorie”, „naţiune”, „neam”, „confesiune”, „conştiinţă naţională”, „limbă”, „cultură”, „politică”, ce-şi resemnifică mereu, pentru fiecare dintre vremuri în parte, conţinuturile.THE IDEA OF “DACO-ROMANIANISM” AT THE ROMANIANS LIVING IN TRANSYLVANIA DURING THE MODERN AGEThe long state of territorial fragmentation and political separatism among the Romanians generated a crisis of the leaders’ conscience on the Romanian territory, tension that crystallized the idea of “Daco-Romanianism”. This resulted in the initiation of some national struggles, especially in the Transylvanian area, whose end

  19. Shot-peening effect on the structure, microhardness, and compressive stresses of the austenitic steel 1.4539

    Directory of Open Access Journals (Sweden)

    Barbara Nasiłowska

    2015-06-01

    Full Text Available This article presents shot-peening effect on the structure, microhardness, and compressive stresses of the austenitic steel 1.4539. The research shows strengthening of the top layer and the formation of compressive stresses in the subsurface layers of the shot-peening elements.[b]Keyword[/b]: austenitic steel 1.4539, residual stresses, Waisman-Phillips’a method

  20. DNA-damage-inducible (din) loci are transcriptionally activated in competent Bacillus subtilis

    International Nuclear Information System (INIS)

    Love, P.E.; Lyle, M.J.; Yasbin, R.E.

    1985-01-01

    DNA damage-inducible (din) operon fusions were generated in Bacillus subtilis by transpositional mutagenesis. These YB886(din::Tn917-lacZ) fusion isolates produced increased β-galactosidase when exposed to mitomycin C, UV radiation, or ethyl methanesulfonate, indicating that the lacZ structural gene had inserted into host transcriptional units that are induced by a variety of DNA-damaging agents. One of the fusion strains was DNA-repair deficient and phenotypically resembled a UV-sensitive mutant of B. subtilis. Induction of β-galactosidase also occurred in the competent subpopulation of each of the din fusion strains, independent of exposure to DNA-damaging agents. Both the DNA-damage-inducible and competence-inducible components of β-galactosidase expression were abolished by the recE4 mutation, which inhibits SOS-like (SOB) induction but does not interfere with the development of the component state. The results indicate that gene expression is stimulated at specific loci within the B. subtilis chromosome both by DNA-damaging agents and by the development of competence and that this response is under the control of the SOB regulatory system. Furthermore, they demonstrate that at the molecular level SOB induction and the development of competence are interrelated cellular events

  1. Dinâmica molecular ab initio:aplicações ao estudo de propriedades electrónicas de sistemas moleculares

    OpenAIRE

    Martiniano, Hugo Filipe de Mesquita Costa, 1978-

    2013-01-01

    Tese de doutoramento, Química (Química-Física), Universidade de Lisboa, Faculdade de Ciências, 2013 O método da dinâmica molecular ab initio exibe vantagens significativas para o estudo da estrutura e propriedades electrónicas de sistemas moleculares complexos. No entanto, uma das suas desvantagens é o elevado custo computacional, quando comparado com os métodos de dinâmica molecular clássicos. Um dos modos de resolver este problema é adoptar uma abordagem sequencial, na qual a dinâmica é ...

  2. Manufacturing of microcomponents in a research institute under DIN EN ISO 9001

    Science.gov (United States)

    Maas, Dieter; Karl, Bernhard; Saile, Volker; Schulz, Joachim

    2000-08-01

    The Institute for Microstructure Technology at Forschungszentrum Karlsruhe has implemented a rigorous quality management system and was certified according to the DIN ISO EN 9001 standard in January 2000.

  3. Adam Smith y Sistemas Dinámicos

    Directory of Open Access Journals (Sweden)

    Osvaldo Acuña

    2008-01-01

    Full Text Available Presentamos un sistema dinámico sencillo con dos ecuaciones diferenciales, una representa la trayectoria del precio y la otra la de la cantidad de un bien en una economía. Nuestro modelo se basa sobre todo en la teoría clásica de precios expuesta por Adam Smith en La Riqueza de las Naciones. Al final del trabajo, se presenta, a modo de ejemplo, un estudio para el caso del ganado vacuno en la economía mundial.

  4. Insuficiencia dinámica, crecimiento y desempleo en México, 1974-2012

    OpenAIRE

    Vargas, Blanca L. Avendaño; Hernández, Ignacio Perrotini

    2015-01-01

    El artículo presenta una reformulación de la hipótesis de insuficiencia dinámica de Prebisch (1970), analiza la teoría dinámica de Harrod (1939), la ley Kaldor-Verdoorn (Kaldor, 1966; 1967) y la teoría del crecimiento endógeno de Thirlwall (1969; 2000)Thirlwall and León-Ledesma, 2000. A posteriori estudiamos los determinantes del crecimiento económico y del desempleo en México durante el periodo 1974-2012. Con base en el análisis empírico, sostenemos que una baja tasa de acumulación genera una...

  5. Hydrogen attack of pressure-vessel steel. Progress report, April 1, 1980-March 31, 1981

    International Nuclear Information System (INIS)

    Shewmon, P.G.

    1980-12-01

    The nucleation and growth of methane bubbles in the hydrogen attack of pressure vessel steel has been shown to obey models developed to describe the growth of bubbles limiting the creep ductility of metals. This has been done through studies of the effect of prior deformation on bubble nucleation as well as the effect of methane pressure (stress) and temperature on growth kinetics. A comprehensive model of the factors limiting growth has been developed. Its application to the hydrogen attack of a 2 1/4 Cr-1 Mo steel leads to several interesting predictions

  6. The DinJ/RelE Toxin-Antitoxin System Suppresses Bacterial Proliferation and Virulence of Xylella fastidiosa in Grapevine.

    Science.gov (United States)

    Burbank, Lindsey P; Stenger, Drake C

    2017-04-01

    Xylella fastidiosa, the causal agent of Pierce's disease of grapes, is a slow-growing, xylem-limited, bacterial pathogen. Disease progression is characterized by systemic spread of the bacterium through xylem vessel networks, causing leaf-scorching symptoms, senescence, and vine decline. It appears to be advantageous to this pathogen to avoid excessive blockage of xylem vessels, because living bacterial cells are generally found in plant tissue with low bacterial cell density and minimal scorching symptoms. The DinJ/RelE toxin-antitoxin system is characterized here for a role in controlling bacterial proliferation and population size during plant colonization. The DinJ/RelE locus is transcribed from two separate promoters, allowing for coexpression of antitoxin DinJ with endoribonuclease toxin RelE, in addition to independent expression of RelE. The ratio of antitoxin/toxin expressed is dependent on bacterial growth conditions, with lower amounts of antitoxin present under conditions designed to mimic grapevine xylem sap. A knockout mutant of DinJ/RelE exhibits a hypervirulent phenotype, with higher bacterial populations and increased symptom development and plant decline. It is likely that DinJ/RelE acts to prevent excessive population growth, contributing to the ability of the pathogen to spread systemically without completely blocking the xylem vessels and increasing probability of acquisition by the insect vector.

  7. An examination of the potential for 9%Cr1%Mo steel as thick section tubeplates in fast reactors

    International Nuclear Information System (INIS)

    Orr, J.; Sanderson, S.J.

    1984-01-01

    The steam generator units of future commercial demonstration fast reactors are likely to have a requirement for heavy section tubeplates (up to 500mm thick) with good elevated temperature strength and creep-fatigue resistance. A comparison of the mechanical properties available for ferritic steels has suggested that 9%Cr1%Mo steel would be a strong candidate material for this application. Although this steel is covered in some national specifications for tubes, pipes, plates and forgings and is also well established in the UK nuclear industry, international experience to date is confined to sections less than ca 150mm. The potential of 9%Cr1%Mo steel for use in thick sections has therefore been assessed in the present study by using simulation heat treatments. The work reported here involved the laboratory-scale cooling of bar samples to simulate water-quenching rates in cylindrical sections up to 720mm diameter (ie: equivalent to 500mm thick plate). The tensile properties at ambient and 525 0 C and impact fracture appearance transition temperatures were determined for material tempered after cooling at simulated thick section rates; the transformation characteristics as influenced by the net chromium equivalent were also established. The results of this work show that 9%Cr1%Mo steel may be fully hardened in the equivalent of the section sizes examined,and the mechanical properties of tempered material show only a small reduction from those of thin section normalised and tempered 9%Cr1%Mo steel. These findings support the potential usage of heavy section 9%Cr1%Mo steel envisaged for fast reactor steam generator tubeplates

  8. Thermal fatigue crack growth tests and analyses of thick wall cylinder made of Mod.9Cr–1Mo steel

    Energy Technology Data Exchange (ETDEWEB)

    Wakai, Takashi, E-mail: wakai.takashi@jaea.go.jp [Japan Atomic Energy Agency, 4002 Narita-cho Oarai, Ibaraki 3111393 (Japan); Inoue, Osamu [IX Knowledge Inc., 3-22-23 MSC Center Bldg, Kaigan Minato-ku, Tokyo 1080022 Japan (Japan); Ando, Masanori; Kobayashi, Sumio [Japan Atomic Energy Agency, 4002 Narita-cho Oarai, Ibaraki 3111393 (Japan)

    2015-12-15

    Highlights: • A thermal fatigue crack growth test was performed using Mod.9Cr–1Mo steel cylinder. • Axial/circumferential notches were machined on the inner surface of the cylinder. • Simplified analytical results were compared to the test data. • Crack length could not be predicted by the analyses because of crack conjunctions. • If there are no surface cracks, the calculations might agree with the observations. - Abstract: In Japan, the basic designing works for a demonstration plant of Japan Sodium cooled Fast Reactor (JSFR) are now conducted. JSFR is an advanced loop type reactor concept. To enhance the safety and the economic competitiveness, JSFR employs modified 9% chromium–1% molybdenum (Mod.9Cr–1Mo) steel as a material for coolant pipes and components, because the steel has both excellent high temperature strength and thermal properties. The steel has been standardized as a nuclear material in Japan Society of Mechanical Engineers (JSME) code in 2012. In JSFR pipes, demonstration of Leak Before Break (LBB) aspect is strongly expected because the safety assessment may be performed on the premise of leak rate where the LBB aspect is assured. Although the authors have already performed a series of thermal fatigue crack growth tests of austenitic stainless steel cylinders (Wakai et al., 2005), crack growth behavior in the structures made of Mod.9Cr–1Mo steel has not been investigated yet. Especially for the welded joints of Mod.9Cr–1Mo steel, “Type-IV” cracking may occur at heat affected zone (HAZ). Therefore, this study performed a series of thermal fatigue crack growth tests of thick wall cylinders made of Mod.9Cr–1Mo steel including welds, to obtain the crack growth data under cyclic thermal transients. The test results were compared to the analytical results obtained from JAEA's simplified methods (Wakai et al., 2005).

  9. Modelagem de uma unidade de produção para caprinos leiteiros utilizando a dinâmica de sistemas

    OpenAIRE

    Guimarães, Vinicius Pereira

    2007-01-01

    O trabalho foi desenvolvido buscando abordar as características de dinâmica, complexidade e inter- relacionamento de um sistema de produção de caprinos. Buscou-se, através da metodologia de modelagem e simulação Dinâmica de Sistemas, identificar o impacto na dinâmica e rentabilidade econômica de rebanhos caprinos leiteiros provocados por modificações no manejo reprodutivo, mortalidade, qualidade do alimento e na idade para o início da vida reprodutiva em cabritas. Buscou-se também avaliar a u...

  10. Evolución Dinámica de Cúmulos Estelares Abiertos

    Science.gov (United States)

    de La Fuente Marcos, R.

    Las estrellas que observamos no se formaron aisladamente, sino que lo hicieron en grupos o cúmulos. Estos sistemas estelares recibenel nombre de cúmulos estelares abiertos o galácticos cuando están constituidos por estrellas de la Población I. Los cúmulos abiertos se localizan preferentemente en el plano galáctico, y en muchos de ellos está teniendo lugar aún una activa formación estelar. El propósito principal de esta tesis doctoral es el estudio de la evolución dinámica de estos sistemas estelares por medio de simulaciones numéricas y de la comparación de sus resultados con datos observacionales. Con este fin se analizan los efectos que, sobre la dinámica de los cúmulos, ejercen varios fenómenos de interés astrofísico tales como el campo gravitatorio galáctico, la pérdida de masa causada por la evolución estelar y la presencia de binarias primordiales. En este trabajo se presentan los resultados de más de un centenar de modelos de cúmulos, con poblaciones comprendidas en el intervalo [100, 10.000] estrellas, calculados con NBODY5, un programa estándar en el campo de la Dinámica Estelar Experimental. De los mismos se deduce que el mecanismo principal que rige la dinámica de los cúmulos abiertos es la evolución estelar de su distribución de masas, encontrándose un comportamiento diferencial fuertemente dependiente de la población inicial del cúmulo. Los mecanismos responsables de la desintegración de los cúmulos abiertos son analizados en detalle, proponiéndose un modelo analítico que ajusta razonablemente los resultados de las simulaciones. Además, y con el fin de explicar el elevado número de sistemas múltiples observados en cúmulos abiertos, se estudian los efectos que, sobre los mismos, ejerce la presencia de una cierta fracción de binarias primordiales. El papel de las binarias tambiín depende de la riqueza del cúmulo y sus efectos se interrelacionan con aquellos debidos a la evolución estelar. Por último, se

  11. DNA Polymerases ImuC and DinB Are Involved in DNA Alkylation Damage Tolerance in Pseudomonas aeruginosa and Pseudomonas putida.

    Science.gov (United States)

    Jatsenko, Tatjana; Sidorenko, Julia; Saumaa, Signe; Kivisaar, Maia

    2017-01-01

    Translesion DNA synthesis (TLS), facilitated by low-fidelity polymerases, is an important DNA damage tolerance mechanism. Here, we investigated the role and biological function of TLS polymerase ImuC (former DnaE2), generally present in bacteria lacking DNA polymerase V, and TLS polymerase DinB in response to DNA alkylation damage in Pseudomonas aeruginosa and P. putida. We found that TLS DNA polymerases ImuC and DinB ensured a protective role against N- and O-methylation induced by N-methyl-N'-nitro-N-nitrosoguanidine (MNNG) in both P. aeruginosa and P. putida. DinB also appeared to be important for the survival of P. aeruginosa and rapidly growing P. putida cells in the presence of methyl methanesulfonate (MMS). The role of ImuC in protection against MMS-induced damage was uncovered under DinB-deficient conditions. Apart from this, both ImuC and DinB were critical for the survival of bacteria with impaired base excision repair (BER) functions upon alkylation damage, lacking DNA glycosylases AlkA and/or Tag. Here, the increased sensitivity of imuCdinB double deficient strains in comparison to single mutants suggested that the specificity of alkylated DNA lesion bypass of DinB and ImuC might also be different. Moreover, our results demonstrated that mutagenesis induced by MMS in pseudomonads was largely ImuC-dependent. Unexpectedly, we discovered that the growth temperature of bacteria affected the efficiency of DinB and ImuC in ensuring cell survival upon alkylation damage. Taken together, the results of our study disclosed the involvement of ImuC in DNA alkylation damage tolerance, especially at low temperatures, and its possible contribution to the adaptation of pseudomonads upon DNA alkylation damage via increased mutagenesis.

  12. A dinâmica da gestão no contexto acadêmico

    Directory of Open Access Journals (Sweden)

    Nadi Helena Presser

    2011-09-01

    Full Text Available Apresenta um estudo da dinâmica da gestão, procurando avançar no assunto, a partir das constatações de Mintzberg (2001, 2010, desmistificando o gestor nas suas características convencionais prescritas pela teoria clássica de administração, denotado como um planejador sistemático, que trabalha de forma programada, sem interrupções, e possuidor de um controle amplo de seu trabalho na organização. O objeto empírico desta pesquisa estendeu sua ação no ambiente organizacional de um departamento universitário federal, no contexto da gestão acadêmica dos cursos de graduação e do programa de pós-graduação. Com apoio numa metodologia de pesquisa etnográfica e de entrevistas semiestruturadas, observou-se um ambiente de gestão caracterizado pela ambiguidade, por uma dinâmica acelerada de tarefas diversificadas. Conclui-se que as análises sobre a prática da gestão teriam a ganhar se procurassem perscrutar esta realidade. A premissa sobre a dinâmica da gestão defendida por Mintzberg encontra sustentação neste estudo, cuja essência é descrita muito mais como uma prática do que como uma ciência.

  13. Steel Industry Wastes.

    Science.gov (United States)

    Schmidtke, N. W.; Averill, D. W.

    1978-01-01

    Presents a literature review of wastes from steel industry, covering publications of 1976-77. This review covers: (1) coke production; (2) iron and steel production; (3) rolling operations; and (4) surface treatment. A list of 133 references is also presented. (NM)

  14. Studies on the welding of heavy-section ASTM A542 Cl. 1 steel for large-sized pressure vessels

    International Nuclear Information System (INIS)

    Shimizu, Shigeki; Aota, Toshiichi; Kasahara, Masayuki

    1977-01-01

    ASTM A 542, Cl. 1 steel was developed and standardized recently, and is excellent in the high temperature strength and toughness as compared with conventionally used A 387, Grade 22 steel, accordingly the application to large pressure vessels is planned. This steel is a low alloy steel, and in case of large thickness, the possibility of cracking in the welded part is large. Also many times of annealing are required for the prevention of welding cracking, the relieving of residual stress, and the softening of hardened portion, but the possibility of cracking during stress-relieving annealing is large. In this study, Tekken type cracking test was carried out by coated electrode welding, and restricted cracking test was carried out by submerged arc welding of the A 542, Cl. 1 steel and A 387, Grade 22 steel, thus the welding cracking property was investigated, and the optimal welding conditions were selected. Also the test of cracking during the stress-relieving annealing of both steels was carried out, and the method of preventing the cracking was studied. The optimal conditions of stress-relieving annealing were selected, and the mechanism of the cracking was clarified. The mechanical properties of the joints welded and stress-relieved under the selected conditions were confirmed. (Kako, I.)

  15. Primeros pasos en la posturografía dinámica computarizada

    Directory of Open Access Journals (Sweden)

    Cristina CORDERO-CIVANTOS

    2018-01-01

    Full Text Available Introducción y objetivo: La posturografía dinámica computarizada (CDP es una técnica que nos va a permitir cuantificar de forma objetiva, como las diferentes patologías afectan la estabilidad postural de los pacientes y su evolución. Metodología: revisión narrativa. Resultados: En este trabajo vamos a repasar como se realizan y analizan las diferentes pruebas de la CDP; y su utilidad diagnóstica y terapéutica en la práctica otorrinolaringológica. Discusión y conclusiones: La posturografía dinámica computarizada es una prueba diagnóstico-terapéutica que permite cuantificar de forma objetiva y reproducible la estabilidad del paciente. Y aporta información relevante para planificar el tratamiento rehabilitador, así como para monitorizar su evolución.

  16. Synthesis and characterization of a novel organic corrosion inhibitor for mild steel in 1 M hydrochloric acid

    Science.gov (United States)

    Ahmed, Mohammed H. Othman; Al-Amiery, Ahmed A.; Al-Majedy, Yasmin K.; Kadhum, Abdul Amir H.; Mohamad, Abu Bakar; Gaaz, Tayser Sumer

    2018-03-01

    The synthesis and characterization of a novel organic corrosion inhibitor (4-(3-mercapto-5,6,7,8-tetrahydro-[1,2,4]triazolo[4,3-b][1,2,4,5]tetrazin-6-yl)phenol), for mild steel in 1 M hydrochloric acid (HCl) has been successfully reported for the first time. The inhibitor evaluated as corrosion inhibitor for mild steel in 1 M of Hydrochloric acid solution using electrochemical impedance spectroscopy (EIS), and electrochemical frequency modulation (EFM) measurement techniques. Changes in the impedance parameters suggested an adsorption of the inhibitor onto the mild steel surface, leading to the formation of protective films. The results show that the inhibition efficiencies increased with increasing the concentrations of the inhibitors and decreased with increasing temperature. The maximum inhibition efficiency up to 67% at the maximum concentration 0.5 mM. This shows that those inhibitors are effective in helping to reduce and slowing down the corrosion process that occurs to mild steel with a hydrochloric acid solution by providing an organic inhibitor for the mild steel that can be weakened by increasing the temperature. The adsorption process of the synthesized organic inhibitor depends on its electronic characteristics in addition to steric effects and the nature of metal surface, temperature degree and the varying degrees of surface-site activity. The synthesized inhibitor molecules were absorbed by metal surface and follow Langmuir isotherms.

  17. Thermoelastoviscoplastic modeling of RAFM steel JLF-1 using tensile and low cycle fatigue experiments

    Energy Technology Data Exchange (ETDEWEB)

    Msolli, S., E-mail: sabeur.msolli@univ-lorraine.fr

    2014-08-01

    In this paper, a modeling of the elastoviscoplastic behavior of a Reduced Activation Ferritic Martensitic (RAFM) steel JLF-1 is presented. The modeling of this material was based on various Low Cycle Fatigue (LCF) and tensile tests performed in air and vacuum using different imposed strain rates and temperature ranges going from ambient temperature to 873 K. The coupled viscoplastic model is coded in FORTRAN program, implemented into the finite elements code ABAQUS and used to predict the thermomechanical behavior of a fatigue specimen made of RAFM steel JLF-1. Good agreements were found between numerical results and experimental data.

  18. Effect of HTGR helium on fatigue and creep properties of 2 1/4Cr-1Mo steel

    International Nuclear Information System (INIS)

    Kurumaji, T.; Yamazaki, H.; Kudo, A.

    1982-01-01

    Low cycle fatigue and creep tests have been carried out on 2 1/4Cr-1Mo steel (candidate steel for VHTR reactor pressure vessel) in helium environment containing 200 approx. 300 μatm of H 2 , 100 approx. 150 μatm CO, 7 approx. 10 μatm CH 4 , 7 approx. 10 μatm CO 2 and 1 μatm H 2 O (JAERI B Helium). Fatigue life in helium environment was longer than that in air at 450 0 C. This results can be explained by supposing that oxidation at the crack tip causes the wedge effect to promote crack propagation in air. On the otherhand, creep rupture strength showed no significant difference in both helium and air. Equivalent creep rupture strength in both helium and air may be due to the fact that detrimental internal oxidation and carburization or decarburization hardly occur at 400 approx. 450 0 C

  19. Synthesis and characterization of a novel organic corrosion inhibitor for mild steel in 1 M hydrochloric acid

    Directory of Open Access Journals (Sweden)

    Mohammed H. Othman Ahmed

    2018-03-01

    Full Text Available The synthesis and characterization of a novel organic corrosion inhibitor (4-(3-mercapto-5,6,7,8-tetrahydro-[1,2,4]triazolo[4,3-b][1,2,4,5]tetrazin-6-ylphenol, for mild steel in 1 M hydrochloric acid (HCl has been successfully reported for the first time. The inhibitor evaluated as corrosion inhibitor for mild steel in 1 M of Hydrochloric acid solution using electrochemical impedance spectroscopy (EIS, and electrochemical frequency modulation (EFM measurement techniques. Changes in the impedance parameters suggested an adsorption of the inhibitor onto the mild steel surface, leading to the formation of protective films. The results show that the inhibition efficiencies increased with increasing the concentrations of the inhibitors and decreased with increasing temperature. The maximum inhibition efficiency up to 67% at the maximum concentration 0.5 mM. This shows that those inhibitors are effective in helping to reduce and slowing down the corrosion process that occurs to mild steel with a hydrochloric acid solution by providing an organic inhibitor for the mild steel that can be weakened by increasing the temperature. The adsorption process of the synthesized organic inhibitor depends on its electronic characteristics in addition to steric effects and the nature of metal surface, temperature degree and the varying degrees of surface-site activity. The synthesized inhibitor molecules were absorbed by metal surface and follow Langmuir isotherms. Keywords: Corrosion, Inhibitor, Mild steel, EIS spectroscopy

  20. Creep and microstructural processes in a low-alloy 2.25%Cr1.6%W steel (ASTM Grade 23)

    Czech Academy of Sciences Publication Activity Database

    Kuchařová, Květa; Sklenička, Václav; Kvapilová, Marie; Svoboda, Milan

    2015-01-01

    Roč. 109, NOV (2015), s. 1-8 ISSN 1044-5803 R&D Projects: GA TA ČR TA02010260; GA MŠk(CZ) ED1.1.00/02.0068 Institutional support: RVO:68081723 Keywords : Bainitic steel * Low-alloy steel * Creep strength * Microstructural changes * Carbide precipitation Subject RIV: JG - Metallurgy Impact factor: 2.383, year: 2015

  1. Comparative assessment of microstructure and texture in the Fe-30.5Mn-8.0Al-1.2C and Fe-30.5Mn-2.1Al-1.2C steels under cold rolling

    Directory of Open Access Journals (Sweden)

    Fabrício Mendes Souza

    Full Text Available Abstract Investigation of microstructure and texture has been done for cold rolled Fe-30.5Mn-8.0Al-1.2C (8Al and Fe-30.5Mn-2.1Al-1.2C (2Al (wt.% steels. They were rolled to a strain of ~0.70. Refinement of a crystallographic slip band substructure in low to medium rolling strain and nucleation of twins on the mature slip bands at a higher strain were suggested as deformation mechanisms in the 8Al steel. Mainly shear banding contributed to the formation of a Copper texture in such steel. Brass-texture development in the 2Al steel is mainly due to deformation twinning and shear banding formation. Detailed images of KAM maps showed that the stored deformation energy was mainly localized in the twinned areas and shear bands, which generated the inhomogeneous deformation microstructures in both steels at a higher strain. Goss and Brass texture intensity decreases and Cu-texture intensity increases as the Al wt.% increases in different cold rolled High-Mn (Mn ~30 wt.% steels.

  2. Effects of heat treatment condition on the mechanical properties and weldability of 10Cr-1Mo-VNbN cast steel

    International Nuclear Information System (INIS)

    Shon, Dae Young; Bang, Kook Soo; Lee, Kyong Woon; Chi, Byung Ha

    2003-01-01

    Mechanical properties and weldability such as HAZ hardness, cold cracking susceptibility and hot ductility of two differently heat treated 10Cr-1Mo-VNbN cast steels were measured and compared. Because of high hardenability of the cast steel, as-annealed cast steel showed martensitic microstructure and thus had higher hardness than annealed-normalized-tempered cast steel which had tempered martensite. Because the welding electrode used resulted in a high hardness weld metal, both cast steels showed same weld metal cold cracking susceptibility even though the as-annealed cast steel had higher HAZ hardness than the annealed-normalized-tempered cast steel. Both cast steels had excellent hot ductility in high temperature range, indicating no risk of grain boundary liquation cracking in the HAZ. However, the as-annealed cast steel showed an inferior ductility in the intermediate temperature range of 1000∼1150 .deg. C because of larger unrecrystallized grain size

  3. Effect of carbon activity on the creep behaviour of 21/4Cr, 1Mo steel in sodium

    International Nuclear Information System (INIS)

    Cordwell, J.E.; Charnock, W.; Nicholson, R.D.

    1979-02-01

    The creep endurance and creep cracking behaviour of 2 1/4Cr, 1Mo steel in sodium at 475 0 C have been studied at three different sodium carbon activities. Creep endurance was found to increase with increasing carbon activity of the sodium. Tests carried out in high carbon activity sodium were discontinued before fracture. Creep crack initiation displacement at notches decreased with increasing carbon activity, presumably as a result of notch tip carburisation. The plastic zones at the tips of blunt notches in specimens exposed in high carbon activity sodium were preferentially carburised. These observations were similar to those made previously on 9Cr, 1Mo steel. One difference detected metallographically was that in a high carburising environment uniform carburisation was obtained in the 2 1/4Cr, 1Mo steel specimens whereas carburisation gradients were observed in the 9Cr, 1Mo steel. Creep crack propagation rates for given notch opening displacement rates in low and intermediate carbon activity sodium were indistinguishable. However, the strenthening that resulted from the mild carburisation of the specimen in the intermediate carbon activity sodium caused slower notch opening displacement rates and crack propagation rates than in the low carbon activity sodium, when the rates were compared at the same crack length. (author)

  4. Land subsidence in the Cerro Prieto Geothermal Field, 1 Baja California, Mexico, from 1994 to 2005. An integrated analysis of DInSAR, levelingand geological data.

    Energy Technology Data Exchange (ETDEWEB)

    Sarychikhina, O; Glowacka, E; Mellors, R; Vidal, F S

    2011-03-03

    Cerro Prieto is the oldest and largest Mexican geothermal field in operation and has been producing electricity since 1973. The large amount of geothermal fluids extracted to supply steam to the power plants has resulted in considerable deformation in and around the field. The deformation includes land subsidence and related ground fissuring and faulting. These phenomena have produced severe damages to infrastructure such as roads, irrigation canals and other facilities. In this paper, the technique of Differential Synthetic Aperture Radar Interferometry (DInSAR) is applied using C-band ENVISAR ASAR data acquired between 2003 and 2006 to determine the extent and amount of land subsidence in the Mexicali Valley near Cerro Prieto Geothermal Field. The DInSAR results were compared with published data from precise leveling surveys (1994- 1997 and 1997-2006) and detailed geological information in order to improve the understanding of temporal and spatial distributions of anthropogenic subsidence in the Mexicali Valley. The leveling and DInSAR data were modeled to characterize the observed deformation in terms of fluid extraction. The results confirm that the tectonic faults control the spatial extent of the observed subsidence. These faults likely act as groundwater flow barriers for aquifers and reservoirs. The shape of the subsiding area coincides with the Cerro Prieto pull-apart basin. In addition, the spatial pattern of the subsidence as well as changes in rate are highly correlated with the development of the Cerro Prieto Geothermal Field.

  5. EVALUAREA POTENŢIALULUI PATRIMONIAL AL ÎNTREPRINDERILOR ŞI ORGANIZAŢIILOR DIN SISTEMUL COOPERAŢIEI DE CONSUM DIN REPUBLICA MOLDOVA

    Directory of Open Access Journals (Sweden)

    Natalia CHIBERCEA

    2018-03-01

    Full Text Available În articol este efectuată o analiză a situaţiei financiar-patrimoniale a entităților economice din sistemul cooperației de consum din Republica Moldova, ceea ce a permis autorului să constate că aceasta indică o stare concretă a capitalului entității economice, reprezentând rezultatul realizării scopului activității întreprinderii. În mod particular, în urma desfăşurării reuşite a activităţii economico-financiare, se constată o creştere a activelor controlate de întreprindere, fapt ce reflectă extinderea activităţii de întreprinzător şi sporirea potenţialului economico-financiar.EVALUATION OF THE PATRIMONIAL POTENTIAL OF THE ENTERPRISES AND ORGANIZATIONS FROM THE CONSUMER COOPERATION SYSTEM OF THE REPUBLIC OF MOLDOVAThis article reflects the analysis of the financial-patrimonial situation of economic entities from the consumer coope­ration system of theRepublicofMoldova, which in general made possible to ascertain that this is a concrete state of the economic entity's capital, representing the result of achieving the purpose of the enterprise's activity. In particular, following the successful conduct of the economic and financial activity, there is an increase in the assets controlled by the enterprise, which reflects the widening of the entrepreneurial activity and increasing economic and financial potential.

  6. Weldability of Stainless Steels

    International Nuclear Information System (INIS)

    Saida, Kazuyoshi

    2010-01-01

    It gives an outline of metallographic properties of welding zone of stainless steels, generation and mechanisms of welding crack and decreasing of corrosion resistance of welding zone. It consists of seven chapters such as introduction, some kinds of stainless steels and properties, metallographic properties of welding zone, weld crack, toughness of welding zone, corrosion resistance and summary. The solidification modes of stainless steels, each solidification mode on the cross section of Fe-Cr-Ni alloy phase diagram, each solidification mode of weld stainless steels metal by electron beam welding, segregation state of alloy elements at each solidification mode, Schaeffler diagram, Delong diagram, effects of (P + S) mass content in % and Cr/Ni equivalent on solidification cracking of weld stainless steels metal, solidification crack susceptibility of weld high purity stainless steels metal, effects of trace impurity elements on solidification crack susceptibility of weld high purity stainless steels metal, ductile fracture susceptibility of weld austenitic stainless steels metal, effects of H2 and ferrite content on generation of crack of weld 25Cr-5N duplex stainless steels, effects of O and N content on toughness of weld SUS 447J1 metals, effect of ferrite content on aging toughness of weld austenitic stainless steel metal, corrosion morphology of welding zone of stainless steels, generation mechanism of knife line attack phenomenon, and corrosion potential of some kinds of metals in seawater at room temperature are illustrated. (S.Y.)

  7. Precipitation behavior in austenitic and ferritic steels during fast neutron irradiation and thermal aging*1

    Science.gov (United States)

    Kawanishi, H.; Hajima, R.; Sekimura, N.; Arai, Y.; Ishino, S.

    1988-07-01

    Precipitation behavior has been studied using a carbon extraction replica technique in Ti-modified Type 316 stainless steels (JPCA-2) and 9Cr-2Mo ferritic/martensitic steels (JFMS) irradiated to 8.1 × 10 24 n/m 2 at 873 and 673 K, respectively, in the experimental fast breeder reactor JOYO. Precipitate identification and compositional analysis were carried out on extracted replicas. The results were compared to those from the as-received steel and a control which had been given the same thermal as-treatment as the specimens received during irradiations. Carbides, Ti-sulphides and phosphides were precipitated in JPCA-2. Precipitate observed in JFMS included carbides, Laves-phases and phosphides. The precipitates in both steels were concluded to be stable under irradiation except for MC and M 6C in JPCA-2. Small MC particles were found precipitated in JPCA-2 during both irradiation and aging. Irradiation proved to promote the precipitation of M 6C in JPCA-2.

  8. Electrochemical Studies of Monoterpenic Thiosemicarbazones as Corrosion Inhibitor for Steel in 1 M HCl

    Directory of Open Access Journals (Sweden)

    R. Idouhli

    2018-01-01

    Full Text Available We have studied the inhibitory effect of some Monoterpenic Thiosemicarbazones on steel corrosion in 1 M HCl solution. The potentiodynamic polarization and electrochemical impedance spectroscopy were used. The Monoterpenic Thiosemicarbazones have inhibited significantly the dissolution of steel. The inhibition efficiency increased with increasing inhibitor concentration and also with the increase in temperature (293–323 K. Furthermore, the results obtained revealed that the adsorption of inhibitor on steel surface obeys Langmuir adsorption model and the thermodynamic parameters such as enthalpy and activation energy were determined. The scanning electron microscopy combined with dispersive X-ray spectroscopy examinations were used to see the shape of the surface morphology and to determine the elemental composition. Scanning electron microscope (SEM images show that the surface damage decreases when the inhibitor is added. The quantum chemical calculations using density functional theory (DFT were performed in order to provide some insights into the electronic density distribution as well as the nature of inhibitor-steel interaction.

  9. Establishment of Wear Resistant HVOF Coatings for 50CrMo4 Chromium Molybdenum Alloy Steel as an Alternative for Hard Chrome Plating

    Science.gov (United States)

    Karuppasamy, S.; Sivan, V.; Natarajan, S.; Kumaresh Babu, S. P.; Duraiselvam, M.; Dhanuskodi, R.

    2018-05-01

    High cost imported components of seamless steel tube manufacturing plants wear frequently and need replacement to ensure the quality of the product. Hard chrome plating, which is time consuming and hazardous, is conventionally used to restore the original dimension of the worn-out surface of the machine components. High Velocity Oxy-Fuel (HVOF) thermal spray coatings with NiCrBSi super alloy powder and Cr3C2 NiCr75/25 alloy powder applied on a 50CrMo4 (DIN-1.7228) chromium molybdenum alloy steel, the material of the wear prone machine component, were evaluated for use as an alternative for hard chrome plating in this present work. The coating characteristics are evaluated using abrasive wear test, sliding wear test and microscopic analysis, hardness test, etc. The study results revealed that the HVOF based NiCrBSi and Cr3C2NiCr75/25 coatings have hardness in the range of 800-900 HV0.3, sliding wear rate in the range of 50-60 µm and surface finish around 5 microns. Cr3C2 NiCr75/25 coating is observed to be a better option out of the two coatings evaluated for the selected application.

  10. Influence of the fabrication process parameters on microstructures and mechanical properties of 10Cr-1Mo ODS steel

    International Nuclear Information System (INIS)

    Jin, Hyun Ju; Kim, Ki Baik; Choi, Byoung Kwon; Kang, Suk Hoon; Noh, Sang Hoon; Kim, Ga Eon; Kim, Tae Kyu

    2016-01-01

    Oxide dispersion strengthened (ODS) FM steels have been developed as the most promising core structural material for high- temperature components operating in severe environments such as nuclear fusion and fission systems owing to its excellent elevated temperature strength and radiation resistance stemming from the addition of extremely thermally stable oxide particles dispersed in a ferritic/martensitic matrix. To realize the structural components such as plates, sheets and tubes in SFR, the development of manufacturing processes is an essential issue for the ODS FM steel. While the ODS steel has superior radiation resistance and high temperature strength, in comparison with the existing commercial steels, it is difficult for the ODS steel to obtain sufficient workability for the fabrication due to high hardness and low ductility at room temperature, meaning that the manufacturing of the ODS plate including cladding tube can be complicated by the low cold workability. In order to prevent the ODS steel from any damage during the manufacturing process, thus, the introduction of intermediate heat treatments between cold rolling processes is necessary. This study investigates effects of the fabrication process parameters such as the cold working ratio, the intermediate and final heat treatments on the microstructure and mechanical properties of 10Cr-1Mo ODS steel. In an effort to optimize the manufacturing route of the ODS FM steel, the microstructural and mechanical evolutions for the ODS plate manufactured by a control of the fabrication process parameters were evaluated in the present study. In the present study, the effect of a cold rolling and intermediate heat treatments on microstructures and mechanical properties of 10Cr-1Mo FM ODS steel were investigated. During the manufacturing route the hardness measurements remained below the critical value of 400 Hv. Intermediate heat treatment with slow cooling led to a softened ferritic structures which can be further

  11. Solidification Segregation and Homogenization Behavior of 1Cr-1.25Mo-0.25V Steel Ingot

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Dong-Bae [Dae-gu Mechatronics and Materials Institute, Daegu (Korea, Republic of); Na, Young-Sang; Seo, Seong-Moon [Korea Institute of Materials Science, Changwon (Korea, Republic of); Lee, Je-Hyun [Changwon National University, Changwon (Korea, Republic of)

    2016-09-15

    As a first step to optimizing the homogenization heat treatment following high temperature upset forging, the solidification segregation and the homogenization behaviors of solute elements were quantitatively analyzed for 1Cr-1.25Mo-0.25V steel ingot by electron probe micro-analysis (EPMA). The random sampling approach, which was designed to generate continuous compositional profiles of each solute element, was employed to clarify the segregation and homogenization behaviors. In addition, ingot castings of lab-scale and a 16-ton-sized 1Cr-1.25Mo-0.25V steel were simulated using the finite element method in three dimensions to understand the size effect of the ingot on the microsegregation and its reduction during the homogenization heat treatment. It was found that the microsegregation in a large-sized ingot was significantly reduced by the promotion of solid state diffusion due to the extremely low cooling rate. On the other hand, from the homogenization point of view, increasing the ingot size causes a dramatic increase in the dendrite arm spacing, and hence the homogenization of microsegregation in a large-sized ingot appears to be practically difficult.

  12. The DNA damage-inducible dinD gene of Escherichia coli is equivalent to orfY upstream of pyrE

    DEFF Research Database (Denmark)

    Lundegaard, Claus; Jensen, Kaj Frank

    1994-01-01

    The DNA damage-inducible gene dinD, originally identified by Kenyon and Walker (C. J. Kenyon and G. C. Walker, Proc. Natl. Acad. Sci. USA 77:2819-2823, 1980) by selection of the dinD::MudI (Ap lac) fusion, is shown here to be equivalent to the open reading frame orfY near pyrE. The evidence...

  13. Investigation of fretting corrosion of vacuum-chrome-plated vt3-1 titanium alloy in pair with unprotected vt3-1 alloy and 40khnma steel

    International Nuclear Information System (INIS)

    Rojkh, I.L.; Koltunova, L.N.; Vejtsman, M.G.; Birman, Ya.N.; Skosarev, A.V.; Kogan, I.S.

    1978-01-01

    The character of destruction of contacting surfaces in the process of fretting corrosion of titanium alloy VT3-1 chromized in vacuum in pair with unprotected alloy VT3-1 and steel 40KhNMA has been studied by scanning electron microscopy, electronography, and recording the surface profile. The specific load was 200 kg/cm 2 , vibration amplitude 50 mkm and frequency 500 Hz. It has been established that pairs unprotected with coating are subjected to intensive fretting corrosion especially when they are made of titanium alloy. For the pair chromized alloy VT3-1 - unprotected alloy VT3-1 no destruction of a chromized surface is observed. Vacuum chromium coating in the pair with steel 40KhNMA reveals similar properties as in pair with a titanium alloy. The surface of a steel sample is destroyed because of fretting corrosion, though the intensity of corrosion is lower than in the case of unprotected pairs. Vacuum chromium coating is recommended for protection of titanium alloy VT3-1 from fretting corrosion in pair with steel 40KhNMA or an alloy VT3-1 especially in those cases when various organic coatings are unsuitable

  14. Equações discretas no ensino médio: modelos de dinâmicas populacionais

    OpenAIRE

    Maligeri, Glaucía Cristina Alecci Meneghim [UNESP

    2013-01-01

    As equações discretas fornecem as ferramentas matemáticas básicas para a correta modelagem da dinâmica populacional ao se tomar como hipótese tempos discretos. Neste trabalho, apresentamos a teoria das equações discretas e algumas aplicações no capítulo 01, dando ênfase aos modelos de dinâmica populacional conhecidos como modelo de Malthus e de Verhulst junto com exemplos que evidenciam tais modelos na modelagem de populações reais. No capítulo 02 apresentamos duas propostas didáticas; a prim...

  15. Influence of He ions irradiation on the deuterium permeation and retention behavior in the CLF-1 steel

    International Nuclear Information System (INIS)

    Xu, Yu-Ping; Lu, Tao; Li, Xiao-Chun; Liu, Feng; Liu, Hao-Dong; Wang, Jing; An, Zhong-Qing; Ding, Fang; Hong, Suk-Ho; Zhou, Hai-Shan; Luo, Guang-Nan

    2016-01-01

    To evaluate the influence of He ions irradiation on the deuterium permeation and retention behavior in RAFM steels, samples made of the CLF-1 steel was irradiated with 3.5 MeV He ions. Gas driven permeation experiments were performed, and the permeability of virgin sample and pre-irradiated sample were obtained and compared. In order to characterize the effect of He ions irradiation on the deuterium retention behavior, deuterium gas exposure was carried out at 623 K, followed by thermal desorption spectra experiments. The total deuterium retention of the CLF-1 steel increased owing to He ions implantation, which could be attributed to the increase in trapping site for deuterium by the He pre-irradiation.

  16. Dinâmica não-linear e psiquiatria: a natureza dinâmica das doenças mentais

    Directory of Open Access Journals (Sweden)

    Fernando Portela Câmara

    2008-03-01

    Full Text Available A psiquiatria moderna adotou a postura reducionista de associar psicopatologia à fisiologia sináptica. Isto produziu avanços importantes na farmacoterapia dos transtornos mentais. Entretanto, a introdução de princípios da dinâmica não-linear promoveu uma mudança do enfoque sináptico para o enfoque das vias específicas patologicamente autônomas envolvidas nos fenômenos psicopatológicos. Esta tendência teve início nos anos 1990 e trouxe um conceito mais sistêmico de fisiopatologia e tratamento em psiquiatria.

  17. Microstructural characterisation and corrosion performance of old railway girder bridge steel and modern weathering structural steel

    International Nuclear Information System (INIS)

    Tewary, N.K.; Kundu, A.; Nandi, R.; Saha, J.K.; Ghosh, S.K.

    2016-01-01

    Highlights: • Microstructure and corrosion performance are compared for two structural steels. • Microstructure evolution shows primarily ferrite-pearlite in both the steels. • Steels show higher corrosion rate in 1% HCl solution than in 3.5% NaCl solution. • The corrosion products show the presence of oxide, hydroxide and oxy-hydroxides. • The corroded surface reveals morphologies like flowery, cotton balls and rosette. - Abstract: A comparison on microstructure and corrosion performance has been made between the two structural steels used in old railway girder bridge (Sample A) and modern grades of weathering structural steel (Sample B). The microstructures, viewed under optical microscope and scanning electron microscope (SEM), show mainly ferrite-pearlite phase constituents in both the steels, A and B. The phase fraction analysis shows higher amount of pearlite in steel A compared to that of steel B. The grain size of steel A is larger than that of steel B under identical processing condition. The immersion corrosion test in 3.5% NaCl shows that the corrosion rate of steel A increases with time, while the same for steel B decreases with time. On the other hand, corrosion test in 1% HCl shows that the corrosion rate of both steel A and B is higher as compared to that of NaCl which always decreases with time. The XRD analysis of corrosion products show the presence of many oxides, hydroxide and oxy-hydroxide like Lepidocrocite (γ-FeOOH), Goethite (α-FeOOH), Akaganeite (β-FeOOH), Magnetite (Fe_3O_4) and Maghemite (γ-Fe_2O_3) in both the steels. The SEM images of corroded surfaces reveal different morphologies like flowery, cotton balls and rosette etc. which indicate that the corrosion products primarily contain Lepidocrocite (γ-FeOOH), Goethite (α-FeOOH) and Akaganeite (β-FeOOH).

  18. La personalidad de las sociedades : descripción y dinámica

    OpenAIRE

    Amigó Borrás, Salvador; Caselles Moncho, Antonio; Micó i Ruiz, Joan Carles

    2018-01-01

    La Extraversión es considerada como la dimensión fundamental y básica de la personalidad desde la Teoría del Rasgo Único de Personalidad [1]. La Extraversión, como dimensión temperamental, engloba dimensiones cognitivas como la racionalidad y la emocionalidad. La teoría de los tipos de Carl Jung [2] establece una dinámica compleja entre estas dimensiones, a partir de la cual se obtiene una tipología de la personalidad. Amigó [3] adaptó la teoría de Jung para aplicarla a las sociedades. Así, a...

  19. Irradiation embrittlement of pressure vessel steels

    International Nuclear Information System (INIS)

    Brumovsky, M.; Vacek, M.

    1975-01-01

    A Standard Research Programme on Irradiation Embrittlement of Pressure Vessel Steels was approved by the Coordinating Meeting on the 12th May 1972 at the Working Group on Engineering Aspects of Irradiation Embrittlement of Pressure Vessel Steels. This Working Group was set up by the International Atomic Energy Agency in Vienna. Seven countries with their research institutes agreed on doing irradiation experiments according to the approved programme on steel A533 B from the U.S. HSST Programme. The Czechoslovak contribution covering tensile and impact testing of non-irradiated steel and steel irradiated at 280degC to 1.3 x 10 23 n/m 2 (E above 1 MeV) is presented in this report. As an additional part the same set of experiments was carried out on two additional steels - A 542 and A 543, made in SKODA Works for comparison of their irradiation embrittlement and hardening with A533 B steel. (author)

  20. Corrosion of an Fe-12 Cr-1 Mo VW steel in thermally-convective lithium

    International Nuclear Information System (INIS)

    Tortorelli, P.F.; DeVan, J.H.

    1983-01-01

    A thermal-convection loop of Fe-12 Cr-1 Mo VW steel circulated pure lithium between 500 and 350 0 C for 10,088 h. Periodic weighings of coupons at different temperatures around the loop revealed small weight losses and corrosion rates. Surface analysis showed a relatively thin corrosion layer with an underlying carbide-free zone and some depletion of chromium from the hottest specimen. While some mass transfer of chromium and nickel was detected, this mechanism did not strongly influence the weight loss process as it does with austenitic steels. Therefore, it appeared that reactions with carbon and nitrogen must be the dominant corrosion processes such that weight loss was maximized at the lowest temperature (350 0 C). Overall, the lithium-steel reactions in the temperature range of this experiment were relatively sluggish and the corrosion was not severe

  1. Pipes out of the chromium-molybdenum 12Kh2M1 steel intended for power units

    International Nuclear Information System (INIS)

    Saf'yanov, A.V.; Plyatskovskij, O.A.; Khokhlov-Nekrasov, O.G.; Palatnikova, E.S.; Karpenko, N.P.

    1977-01-01

    Vanadiumless steel 12Kh2M1 (2.25%Cr, 1%Mo) known to be applied abroad has been used for production of 325x60 mm tubes. The technology involves heating of the blanks to 1270-1300 deg C, their piercing in a double-roller mill, rolling on a pilger mill 8-16'' in thick wall caliber rolls, thermal treatment (normalizing at 930-960 deg C for 1 hour and tempering at 730+-10 deg C for 4 hours and etching (12-22% H 2 SO 4 and up to 143 g/l FeSO 4 ) for 3-4 hours at 55-65 deg C. Good technological properties of the steel and its capacity of working at 540-580 deg C are confirmed. Vanadium alloying of boiler steels does not provide for essential improvement of oxydation resistance and long term strength, but decreases the workability and enhances scatter of working parameters on account of minor variations of chemical composition

  2. A dinâmica do crédito no Brasil entre 1990-2006.

    Directory of Open Access Journals (Sweden)

    Juliano Morais Galle

    2008-05-01

    Full Text Available Este artigo aborda, dentro de um contexto de globalização financeira, a dinâmica e o desenvolvimento recente do mercado financeiro e de crédito no Brasil. É mostrado que a dinâmica do crédito se caracterizou por três fases distintas entre 1990 e 2003. Além disso, discute-se que, após a implantação do Plano Real, houve um grande esforço por parte do governo brasileiro em reestruturar e reforçar o Sistema Financeiro Nacional, e que a conjuntura econômica observada atualmente no Brasil é bem mais favorável ao crescimento da relação crédito/PIB que no início da década de 2000.

  3. Sentinel-1 data massive processing for large scale DInSAR analyses within Cloud Computing environments through the P-SBAS approach

    Science.gov (United States)

    Lanari, Riccardo; Bonano, Manuela; Buonanno, Sabatino; Casu, Francesco; De Luca, Claudio; Fusco, Adele; Manunta, Michele; Manzo, Mariarosaria; Pepe, Antonio; Zinno, Ivana

    2017-04-01

    The SENTINEL-1 (S1) mission is designed to provide operational capability for continuous mapping of the Earth thanks to its two polar-orbiting satellites (SENTINEL-1A and B) performing C-band synthetic aperture radar (SAR) imaging. It is, indeed, characterized by enhanced revisit frequency, coverage and reliability for operational services and applications requiring long SAR data time series. Moreover, SENTINEL-1 is specifically oriented to interferometry applications with stringent requirements based on attitude and orbit accuracy and it is intrinsically characterized by small spatial and temporal baselines. Consequently, SENTINEL-1 data are particularly suitable to be exploited through advanced interferometric techniques such as the well-known DInSAR algorithm referred to as Small BAseline Subset (SBAS), which allows the generation of deformation time series and displacement velocity maps. In this work we present an advanced interferometric processing chain, based on the Parallel SBAS (P-SBAS) approach, for the massive processing of S1 Interferometric Wide Swath (IWS) data aimed at generating deformation time series in efficient, automatic and systematic way. Such a DInSAR chain is designed to exploit distributed computing infrastructures, and more specifically Cloud Computing environments, to properly deal with the storage and the processing of huge S1 datasets. In particular, since S1 IWS data are acquired with the innovative Terrain Observation with Progressive Scans (TOPS) mode, we could benefit from the structure of S1 data, which are composed by bursts that can be considered as separate acquisitions. Indeed, the processing is intrinsically parallelizable with respect to such independent input data and therefore we basically exploited this coarse granularity parallelization strategy in the majority of the steps of the SBAS processing chain. Moreover, we also implemented more sophisticated parallelization approaches, exploiting both multi-node and multi

  4. Crecimiento en longitud foliar y dinámica de población de tallos de cinco asociaciones de gramineas y leguminosa bajo pastoreo

    Directory of Open Access Journals (Sweden)

    Rigoberto Castro Rivera

    2013-01-01

    Full Text Available El objetivo del estudio fue determinar la elongación, crecimiento, senescencia, peso y dinámica de tallos de cinco asociaciones conformadas por dos gramíneas y una leguminosa sembradas en diferentes proporciones. Se evaluaron cinco tratamientos: 4:3:3; 4:6:0; 4:0:6; 4:4:2 y 4:2:4 de trébol blanco-ovillo-ballico perenne, los cuales se distribuyeron en 20 unidades experimentales de 104 m2 , en un diseño en bloques completos al azar. La mayor elongación y crecimiento neto de la hoja de las especies evaluadas fue en verano, con 7.1 y 6.53 cm tallo -1 d -1 , para el pasto ovillo, y 7 y 6.7 cm tallo -1 d -1 , para ballico perenne; en trébol blanco no existió diferencia en el recambio de tejido foliar y del peciolo en verano y primavera ( P>0.05. El mayor peso de tallos de ballico perenne y ovillo se registró en verano (0.38g -1 tallo - 1 y las mayores densidades en la época de invierno (9,961 y 10,423 tallos m-2 , respectivamente. El recambio de tejido de las especies evaluadas presentó marcada estacionalidad, siendo más dinámico en verano que en otoño. La asociación de tres especies permitió una mayor dinámica en comparación con la asociación de dos especies.

  5. Career Dilemmas among Diné (Navajo College Graduates: An Exploration of the Dinétah (Navajo Nation Brain Drain

    Directory of Open Access Journals (Sweden)

    Avery Denny

    2013-11-01

    Full Text Available Like many Indigenous nations, the Navajo Nation has worked to develop its human and economic potential. It has provided scholarships and other supports to enable its members to pursue post-secondary education. However, relatively few of these college-educated members return to the reservation to contribute directly to its development. This phenomenon has been termed a brain drain. This study explored the experiences of 28 college-educated Navajos who, while raised on the reservation, were living off the reservation after completing their post-secondary education. Participants indicated a number of factors that went into their decision to live off the reservation. These included:1. Ké’: Relationships/Connections to Family, Culture, Homeland, People;2. Iiná: Lifestyle/Lifeway, Desirable Setting, Learned Work Ethic, Social Atmosphere, Togetherness (Diné vs. Individualism (Mainstream;Bee ach’į’ na’hwii’ná: Resources and Roadblocks to Making a Life, Infrastructure, Services, The “System”;3. Bee ajit’9: Opportunity, Prosperity and Personal Improvement, Education, Extracurricular, Job Availability, Work Experience.

  6. The creep-fatigue crack growth behaviour of a 1CrMoV rotor steel

    International Nuclear Information System (INIS)

    Priest, R.H.; Miller, D.A.; Gladwin, D.N.; Maguire, J.

    1989-01-01

    Crack growth rates under simultaneous creep-fatigue conditions have been quantified for a 1CrMoV rotor steel. Measured growth rates were partitioned into cyclic and hold period contributions and these characterized by the relevant fracture mechanics parameters K and C. Cyclic growth rates measured in the creep-fatigue tests were enhanced compared with pure fatigue rates. This observation is compared with the behaviour of other steels and explained by quantitative metallography. The resulting crack growth equation can be used during integrity assessments for plant components containing cracks which are subject to thermal fatigue

  7. The effects of minor alloy modifications and heat treatment on the microstructure and creep rupture behavior of 2.25Cr-1Mo Steel

    International Nuclear Information System (INIS)

    Todd, J.A.; Chung, D.W.; Parker, E.R.

    1983-01-01

    The effects of alloy additions on the microstructure of simulated cooled and tempered 2.25Cr-1Mo steels have been studied using transmission electron microscopy. Carbide precipitation sequences have been identified in the modification 3Cr-1Mo-1Mn-1Ni and compared to those in 2.25Cr-1Mo steels modified with Mn and Ni and also with Ti, V and B. The influence of minor compositional changes on the creep rupture behavior of 2.25Cr-1Mo steel has been studied at 500 C, 560 C, and 600 C. The most significant effect of alloy modifications on creep properties resulted from additions of Mn and Cr. Preliminary studies show that 1% Mn and 0.5Mn + 1Ni + 0.75Cr additions significantly reduce creep strength at all three temperatures for tests up to 2000 hours duration. The 3Cr-1Mo-1Mn-1Ni steel showed improvements in rupture ductility at all temperatures when compared with the base 2.25Cr-1Mo steel and the manganese-nickel modifications. Plots of the Larson-Miller parameter for both these modifications lay within the scatter band for commercial 2.25Cr-1Mo steels

  8. The induction furnace as a melting facility in steel production. Pt. 1. Features of induction furnaces used in steel production; Der Induktionsofen als Schmelzaggregat fuer die Stahlerzeugung. T. 1. Merkmale von Induktionsoefen in der Stahlerzeugung

    Energy Technology Data Exchange (ETDEWEB)

    Chaabet, Mohamed; Doetsch, Erwin [ABP Induction Systems GmbH, Dortmund (Germany)

    2011-12-15

    Global steel output has now been growing extremely rapidly for a prolonged time; in the past ten years alone, annual production has risen from 851 million t/a (in 2001) to 1417 million t/a (2010), as a result, primarily, of growth in China. Electric steel production using the electric arc furnace as the classical melting facility is around 45 % world-wide, with a rising trend (but excluding the special case of China, where oxygen-route steel holds a 90 % share of production). Following the development of induction technology and inverter outputs of over 40 MW for crucible furnaces with capacities of above 65 t, the induction furnace is now available as an alternative electrical melting installation for use in smaller mini steel mills. The benefits of this technology can be found in high feed-material efficiencies and low environmental and workplace burdens, in addition to the absence of electrode costs and the only modest demands made on the power-supply grid. These features of the induction furnace and their special significance for steel production are examined in Part 1 of this article. The second part of the article then focuses on examples of the use of induction furnaces in the steelmaking plant. (orig.)

  9. Metafísica y dinámica caótica

    Directory of Open Access Journals (Sweden)

    Vicente Aboites

    2009-01-01

    Full Text Available From an internalist viewpoint for mental states, it is proposed that any dynamical system with coexisting chaotic attractors has an emergent property. This provides a non reductive explanation of mental states and their high sensitivity to noise and initial conditions. If metaphysical terms result from the mental states and these are emergent properties of dynamical systems with coexisting attractors, such as the brain, it is suggested that this may provide a physical explanation of metaphysical concepts. A partir de un enfoque internalista para los estados mentales, se propone que los términos metafísicos son el resultado de estados mentales que, a su vez, son propiedades emergentes de sistemas dinámicos caóticos con atractores coexistentes en el cerebro. Se sugiere que esto proporciona una explicación física para los conceptos metafísicos. Esto se hace a partir de la propuesta de que todos los sistemas dinámicos con atractores coexistentes caóticos, como el cerebro, presentan propiedades emergentes. Obtenemos así una explicación no reductiva de los estados mentales y su alta sensibilidad al ruido y a las condiciones iniciales.

  10. A Comparison of Effective Tension Calculation for Design Belt Conveyor between CEMA and DIN Standard

    Directory of Open Access Journals (Sweden)

    Satria Iman

    2018-01-01

    Full Text Available In the present era, many industries are demanding material transfer equipment that works maximally and cheaply. Belt Conveyor is one of the most efficient material transfer equipment compared to heavy equipment or other transportation equipment, because it can transport the material in large capacity. When designing conveyor belts, many industries want large transport capacity at low cost. One of the cost savings can be done with low motor power consumption. Many standards describe the effective tension calculation on the conveyor belt in detail with the parameters, since the effective tension calculation results are essential for determining motor power. This paper aims to analyze the effective tension on conveyor belts using CEMA 5th, CEMA 6th and DIN 22101 standards with case studies of 1000 TPH carrying capacity and 3 m/s conveyor speed. The difference between CEMA and DIN when determining the effective tension is on the use of coefficient of friction, because DIN uses a global coefficient of friction while CEMA uses different friction coefficients on idler, belt and material. This difference in coefficient of friction results in different ways of calculating the resistance being the accumulation of the effective tension. The result is an effective tension value using DIN 22101 standard of 22,148.16 N with motor power consumption of 66.5 kW, while effective tension value using CEMA 5th standard is 32.201.66 N with motor power consumption 96.47 kW, and effective tension value using CEMA 6th standard is 29,686.48 N with 89.06 kW motor power consumption.

  11. Effect of tensile deformation on micromagnetic parameters in 0.2% carbon steel and 2.25Cr-1Mo steel

    Energy Technology Data Exchange (ETDEWEB)

    Moorthy, V.; Vaidyanathan, S.; Jayakumar, T.; Raj, B. [Indira Gandhi Centre for Atomic Research, Kalpakkam (India). Metallurgy and Materials Group; Kashyap, B.P. [Indian Inst. of Tech., Bombay (India). Dept. of Metallurgical Engineering and Materials Science

    1999-04-23

    The influence of prior tensile deformation on the magnetic Barkhausen emission (MBE) and the hysteresis (B-H) curve has been studied in 0.2% carbon steel and 2.25Cr-1Mo steel under different tempered conditions. This study shows that the micromagnetic parameters can be used to identify the four stages of deformation, namely (1) perfectly elastic, (2) microplastic yielding, (3) macroyielding and (4) progressive plastic deformation. However, it is observed that the MBE profile shows more distinct changes at different stages of tensile deformation than the hysteresis curve. It has been established that the beginning of microplastic yielding and macroyielding can be identified from the MBE profile which is not possible from the stress-strain plot. The onset of microplastic yielding can be identified from the decrease in the MBE peak height. The macroyielding can be identified from the merging of the initially present two-peak MBE profile into a single central peak with relatively higher peak height and narrow profile width. The difference between the variation of MBE and hysteresis curve parameters with strain beyond macroyielding indicates the difference in the deformation state of the surface and bulk of the sample.

  12. V and Nb Influence on the Austenitic Stainless Steel Corrosion in 0.1 M HCl

    Directory of Open Access Journals (Sweden)

    Amel GHARBI

    2014-05-01

    Full Text Available Vanadium and niobium were added in AISI309 austenitic stainless steel composition to modify their structure and pitting corrosion resistance in 0.1 M HCl. The structural characterization was carried out by X-rays diffraction and optical microscopy. Corrosion behavior was investigated using potentiodynamic tests and electrochemical impedance measurements (EIS .Results showed that vanadium and niobium addition precipitated stable carbides (VC, NbC to chromium carbides’ detriment and improved austenitic stainless steel corrosion resistance.

  13. The structure of the alphinizing coat on alloy steels

    Directory of Open Access Journals (Sweden)

    S. Pietrowski

    2008-12-01

    Full Text Available In this paper results of the structure of the coat alphinizing in AlSi5 silumin on alloy steels: acid-proof 1H18N9T (X6CrNiTi18-10 and high speed SW18 (HS18-0-1 were presented. The temperature of the alphinizing bath was amounts to750±5°C, and immersion time of the element τ = 180s. It was shown, that there is the different “g” coat thickness on testing steels. On the 1H18N9T steel it amounts to g = 52μm, and on the SW18 steel – g = 203μm. Regardless of a grade of testing alloy steels the coat consist of three layers with diversified phasic structure. There is different chemical composition of coat layers on testing steels. The first layer from the base consist of AlFe phase containing alloy addictions of steels: Cr and Ni (1H18N9T and W, V and Cr (SW18. On this layer crystallize the second layer of intermetallic phases. It is the phase containing the main alloy addiction of steels: AlFeCr (1H18N9T and AlFeW (SW18. The last, outside layer consist of silumin containing AlFeNi intermetallic phases on the 1H18N9T steel and AlFeW on the SW18 steel. Regardless of the grade of testing steels there is Si element in all layers of the coat. There are morphological differences in tested layers. The second layer (AlFeW phase inside the coat on the SW18 steel consist of faced crystals growing into in outside silumin layer. On the 1H18N9T steel a boundary between transient and outside layer is more uniform. Free separations of intermetallic phases inside silumin layer on the 1H18N9T steel have lamellar and on the SW18 steel – faced form.

  14. Properties of welded joints of 2,25Cr-1Mo steel with various carbon content

    International Nuclear Information System (INIS)

    Vornovitskij, I.N.; Brodetskaya, E.Z.; Pozdnyakova, A.S.

    1980-01-01

    Properties of welded joints of 2,25 Cr - 1 Mo steel pipelines with different carbon content are considered. It is shown that application of electrodes developed in some countries for welding permits in many cases to exclude heat treatment of welded joints owing to high ductility of weld deposited metal. To improve the ductility, it is necessary to limit both carbon content down to 0,03-0,06% and detrimental elements (sulfur, phosphorus). Heat affected zone hardness may be increased at the expense of carbon. Weld deposited metal possesses the highest long-term strength at the given test temperature; in this case long-term strength of welded joints and base metal is practically the same. The long-term strength of high-carbon steel is higher at the test temperature of 565 deg C as compared to mean-carbon and low-carbon steels, whose long-term strength is practically equal at this temperature. The long-term strength of high-carbon and mean-carbon steels is practically the same and higher as compared with low-carbon one at the test temperature of 510 deg C

  15. Effect of the isothermal transformation temperature on the fine structure of steel-12Kh1MF

    International Nuclear Information System (INIS)

    Mints, I.I.; Berezina, T.G.; Lanskaya, K.A.

    1976-01-01

    For detailed analysis of bainite and pearlite in steel 12Kh1MF, homogeneous structures were obtained by isothermal annealing at 350, 450, 500, and 650 0 for 1 h. Isothermal transformation of austenite leads to the formation of bainite at 350-500 0 and pearlite at 650 0 . The austenitizing temperature was 980 0 for both types of samples, with holding for 20 min. For comparison, the plates were quenched from 980 0 and 1050 0 in ice-cold brine. The investigation was conducted with use of light and electron microscopes and x-ray analysis. The long-term strength was also determined. Isothermal treatment of steel 12Kh1MF at 350-500 0 C leads to the formation of a structure consisting of upper and lower bainite. At 500 0 the structure consists primarily of upper bainite, and at 350 0 of lower bainite. With tempering of the steel with a structure of upper and lower bainite at 730 0 for 3 h the dislocations undergo redistribution of the polygonization type within ferrite needles, with development of a cellular substructure. The acicular structure of the matrix is retained in this case. The density and evenness of the distribution of carbides is higher in upper bainite than in lower bainite. Steel 12Kh1MF with a structure of upper bainite is more susceptible to recrystallization as compared with a structure of lower bainite, which is responsible for the higher heat resistance of the latter

  16. Heat treatments in a conventional steel to reproduce the microstructure of a nuclear grade steel

    International Nuclear Information System (INIS)

    Rosalio G, M.

    2014-01-01

    The ferritic steels used in the manufacture of pressurized vessels of Boiling Water Reactors (BWR) suffer degradation in their mechanical properties due to damage caused by the neutron fluxes of high energy bigger to a Mega electron volt (E> 1 MeV) generated in the reactor core. The materials with which the pressurized vessels of nuclear reactors cooled by light water are built correspond to low alloy ferritic steels. The effect of neutron irradiation on these steels is manifested as an increase in hardness, mechanical strength, with the consequent decrease in ductility, fracture toughness and an increase in temperature of ductile-brittle transition. The life of a BWR is 40 years, its design must be considered sufficient margin of safety because pressure forces experienced during operation, maintenance and testing of postulated accident conditions. It is necessary that under these conditions the vessel to behave ductile and likely to propagate a fracture is minimized. The vessels of light water nuclear reactors have a bainite microstructure. Specifically, the reactor vessels of the nuclear power plant of Laguna Verde (Veracruz, Mexico) are made of a steel Astm A-533, Grade B Class 1. At present they are carrying out some welding tests for the construction of a model of a BWR, however, to use nuclear grade steel such as Astm A-533 to carry out some of the welding tests, is very expensive; perform these in a conventional material provides basic information. Although the microstructure present in the conventional material does not correspond exactly to the degree of nuclear material, it can take of reference. Therefore, it is proposed to conduct a pilot study to establish the thermal treatment that reproduces the microstructure of nuclear grade steel, in conventional steel. The resulting properties of the conventional steel samples will be compared to a JRQ steel, that is a steel Astm A-533, Grade B Class 1, provided by IAEA. (Author)

  17. Evaluation of Corrosion Inhibition of Mild Steel in 1 M Hydrochloric Acid Solution by Mollugo cerviana

    Directory of Open Access Journals (Sweden)

    P. Arockiasamy

    2014-01-01

    Full Text Available The inhibiting effect of methanolic extract of Mollugo cerviana plant on the corrosion of mild steel in 1 M HCl solution has been investigated by different techniques like potentiodynamic polarization, electrochemical impedance spectroscopy, and weight loss methods for five different concentrations of plant extract ranging from 25 to 1000 mg/L. The results indicated that the corrosion inhibition efficiency increased on increasing plant extract concentration till 500 mg/L and decreased on further increasing concentration. The extract was a mixed type inhibitor with the optimum inhibition concentration of 500 mg/L in potentiodynamic polarization. The adsorption of the plant extract on the mild steel surface was found to obey Langmuir adsorption isotherm. Surface analysis was also carried out to find out the surface morphology of the mild steel in the presence and in the absence of the inhibitor to find out its efficiency. The obtained results showed that the Mollugo cerviana extract acts as a good inhibitor for the corrosion of mild steel in 1 M HCl solution.

  18. Creep and creep fatigue crack behavior of 1Cr- and 9Cr-steels

    International Nuclear Information System (INIS)

    Maile, K.; Klenk, A.; Schellenberg, G.; Granacher, J.; Tramer, M.

    2000-01-01

    A large database for creep crack initiation and propagation under constant load conditions is available on conventional power plant steels of types 1%Cr and 12%Cr. Modern plants are often used in the medium and peak load regime, thus the dominant loading situation in high temperature components is creep fatigue. For life assessment data about crack initiation and growth under creep fatigue loading are required. These characteristics can not be substituted by pure fatigue or creep crack data. Therefore, a comprehensive test programme was started to investigate the creep fatigue crack behaviour of a 1%CrMoNiV turbine rotor steel (30CrMoNiV 4 11) at 550 C and a new 9%CrMoVNb pipe steel (type P 9 1) at 600 C. DENT-specimen with 15 and 60 mm thickness as well as side grooved CT-specimen with 25 and 50 mm thickness have been tested to determine possible influences of geometry and thus to check the transferability of the data to components. The creep fatigue crack growth results of tests with dwell times between t H = 0,32h and 10 h lie in the scatterbands given by creep crack growth results. Nevertheless a higher crack growth rate under creep fatigue conditions can be stated. An increase in crack growth rate due to creep fatigue is clearly visible. Loading situations with frequencies higher than 1.10 -4 Hz should be not assessed with pure creep crack results or sufficient safety margins have to be applied. (orig.)

  19. Ground deformation monitoring using RADARSAT-2 DInSAR-MSBAS at the Aquistore CO2 storage site in Saskatchewan (Canada)

    Science.gov (United States)

    Czarnogorska, M.; Samsonov, S.; White, D.

    2014-11-01

    The research objectives of the Aquistore CO2 storage project are to design, adapt, and test non-seismic monitoring methods for measurement, and verification of CO2 storage, and to integrate data to determine subsurface fluid distributions, pressure changes and associated surface deformation. Aquistore site is located near Estevan in Southern Saskatchewan on the South flank of the Souris River and west of the Boundary Dam Power Station and the historical part of Estevan coal mine in southeastern Saskatchewan, Canada. Several monitoring techniques were employed in the study area including advanced satellite Differential Interferometric Synthetic Aperture Radar (DInSAR) technique, GPS, tiltmeters and piezometers. The targeted CO2 injection zones are within the Winnipeg and Deadwood formations located at > 3000 m depth. An array of monitoring techniques was employed in the study area including advanced satellite Differential Interferometric Synthetic Aperture Radar (DInSAR) with established corner reflectors, GPS, tiltmeters and piezometers stations. We used airborne LIDAR data for topographic phase estimation, and DInSAR product geocoding. Ground deformation maps have been calculated using Multidimensional Small Baseline Subset (MSBAS) methodology from 134 RADARSAT-2 images, from five different beams, acquired during 20120612-20140706. We computed and interpreted nine time series for selected places. MSBAS results indicate slow ground deformation up to 1 cm/year not related to CO2 injection but caused by various natural and anthropogenic causes.

  20. Evaluation of 2 1/4 Cr-1 Mo steel for liquid lithium containment. II. Effects of post-weld heat treatment and niobium content. Annual report, 1979

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, T.L.; Edwards, G.R.

    1979-01-01

    The lithium corrosion resistance of the regular grade of 2 1/4 Cr-1 Mo steel can be vastly improved with a proper postweld heat treatment, but even greater improvements are needed. Results indicate that if weldments were tempered sufficiently long at 760C to remove all Mo/sub 2/C from the microstructure, even greater resistance to attack by low nitrogen lithium could be achieved. Corrosion tests should eventually be performed on regular grade 2 1/4 Cr-1 Mo steel weldments which have been given a long-term (> 25 h) post-weld temper at 760C. Lithium corrosion resistance of regular grade 2 1/4 Cr-1 Mo steel may also be improved by employing a quench and temper heat treatment. Quenched microstructures have more homogenous distribution of carbides than isothermally annealed microstructures, and if properly tempered, should provide excellent lithium corrosion resistance. Furthermore, the toughness of such a lower bainite microstructure should be better than that of the ferrite-bainitic microstructure created by an isothermal anneal. Numerous parameters, all potentially deleterious to the lithium corrosion resistance of 2 1/4 Cr-1 Mo steel, remain to be investigated; two such variables are velocity effects and lead content in the lithium.

  1. Evaluation of 2 1/4 Cr-1 Mo steel for liquid lithium containment. II. Effects of post-weld heat treatment and niobium content. Annual report, 1979

    International Nuclear Information System (INIS)

    Anderson, T.L.; Edwards, G.R.

    1979-01-01

    The lithium corrosion resistance of the regular grade of 2 1/4 Cr-1 Mo steel can be vastly improved with a proper postweld heat treatment, but even greater improvements are needed. Results indicate that if weldments were tempered sufficiently long at 760C to remove all Mo 2 C from the microstructure, even greater resistance to attack by low nitrogen lithium could be achieved. Corrosion tests should eventually be performed on regular grade 2 1/4 Cr-1 Mo steel weldments which have been given a long-term (> 25 h) post-weld temper at 760C. Lithium corrosion resistance of regular grade 2 1/4 Cr-1 Mo steel may also be improved by employing a quench and temper heat treatment. Quenched microstructures have more homogenous distribution of carbides than isothermally annealed microstructures, and if properly tempered, should provide excellent lithium corrosion resistance. Furthermore, the toughness of such a lower bainite microstructure should be better than that of the ferrite-bainitic microstructure created by an isothermal anneal. Numerous parameters, all potentially deleterious to the lithium corrosion resistance of 2 1/4 Cr-1 Mo steel, remain to be investigated; two such variables are velocity effects and lead content in the lithium

  2. Influence of cooling rates on the transformation behaviour of 9Cr-1Mo-0.07C steel

    International Nuclear Information System (INIS)

    Saroja, S.; Vijayalakshmi, M.; Raghunathan, V.S.

    1992-01-01

    The choice of various decomposition mechanisms of austenite in a 9Cr-1 Mo-0.07C steel under different rates of cooling has been studied. The techniques employed were electron probe micro-analysis, X-ray diffraction and electron microscopy. The observed morphological features may be explained based on the predominance of the two types of transformation, austenite → martensite and austenite → ferrite during cooling. In the steel used in this study, decomposition of austenite to proeutectoid ferrite was favoured at cooling rates less than about 2 Ks -1 . The mechanism by which the supersaturated proeutectoid ferrite relieves its excess solute concentration was also studied. A ''microstructural map'' has been proposed to predict the constitution at the end of any given cooling rate for 9Cr-1 Mo-0.07C steel. The choice of commercial treatment has been rationalized with respect to the resultant microstructural constituents. (Author)

  3. Effect of Welding Processes on the Microstructure, Mechanical Properties and Residual Stresses of Plain 9Cr-1Mo Steel Weld Joints

    Science.gov (United States)

    Nagaraju, S.; Vasantharaja, P.; Brahadees, G.; Vasudevan, M.; Mahadevan, S.

    2017-12-01

    9Cr-1Mo steel designated as P9 is widely used in the construction of power plants and high-temperature applications. It is chosen for fabricating hexcan fuel subassembly wrapper components of fast breeder reactors. Arc welding processes are generally used for fabricating 9Cr-1Mo steel weld joints. A-TIG welding process is increasingly being adopted by the industries. In the present study, shielded metal arc (SMA), tungsten inert gas (TIG) and A-TIG welding processes are used for fabricating the 9Cr-1Mo steel weld joints of 10 mm thickness. Effect of the above welding processes on the microstructure evolution, mechanical properties and residual stresses of the weld joints has been studied in detail. All the three weld joints exhibited comparable strength and ductility values. 9Cr-1Mo steel weld joint fabricated by SMAW process exhibited lower impact toughness values caused by coarser grain size and inclusions. 9Cr-1Mo steel weld joint fabricated by TIG welding exhibited higher toughness due to finer grain size, while the weld joint fabricated by A-TIG welding process exhibited adequate toughness values. SMA steel weld joint exhibited compressive residual stresses in the weld metal and HAZ, while TIG and A-TIG weld joint exhibited tensile residual stresses in the weld metal and HAZ.

  4. Unsupervised DInSAR processing chain for multi-scale displacement analysis

    Science.gov (United States)

    Casu, Francesco; Manunta, Michele

    2016-04-01

    Earth Observation techniques can be very helpful for the estimation of several sources of ground deformation due to their characteristics of large spatial coverage, high resolution and cost effectiveness. In this scenario, Differential Synthetic Aperture Radar Interferometry (DInSAR) is one of the most effective methodologies for its capability to generate spatially dense deformation maps at both global and local spatial scale, with centimeter to millimeter accuracy. DInSAR exploits the phase difference (interferogram) between SAR image pairs relevant to acquisitions gathered at different times, but with the same illumination geometry and from sufficiently close flight tracks, whose separation is typically referred to as baseline. Among several, the SBAS algorithm is one of the most used DInSAR approaches and it is aimed at generating displacement time series at a multi-scale level by exploiting a set of small baseline interferograms. SBAS, and generally DInSAR, has taken benefit from the large availability of spaceborne SAR data collected along years by several satellite systems, with particular regard to the European ERS and ENVISAT sensors, which have acquired SAR images worldwide during approximately 20 years. Moreover, since 2014 the new generation of Copernicus Sentinel satellites has started to acquire data with a short revisit time (12 days) and a global coverage policy, thus flooding the scientific EO community with an unprecedent amount of data. To efficiently manage such amount of data, proper processing facilities (as those coming from the emerging Cloud Computing technologies) have to be used, as well as novel algorithms aimed at their efficient exploitation have to be developed. In this work we present a set of results achieved by exploiting a recently proposed implementation of the SBAS algorithm, namely Parallel-SBAS (P-SBAS), which allows us to effectively process, in an unsupervised way and in a limited time frame, a huge number of SAR images

  5. Risk of lung cancer according to mild steel and stainless steel welding

    DEFF Research Database (Denmark)

    Sørensen, Anita Rath; Thulstrup, Ane Marie; Hansen, Johnni

    2007-01-01

    OBJECTIVES: Whether the elevated risk of lung cancer observed among welders is caused by welding emissions or by confounding from smoking or asbestos exposure is still not resolved. This question was addressed in a cohort with a long follow-up and quantified estimates of individual exposure.......06-1.70)]. Among the stainless steel welders, the risk increased significantly with increasing accumulative welding particulate exposure, while no exposure-response relation was found for mild steel welders, even after adjustment for tobacco smoking and asbestos exposure. CONCLUSIONS: The study corroborates...... earlier findings that welders have an increased risk of lung cancer. While exposure-response relations indicate carcinogenic effects related to stainless steel welding, it is still unresolved whether the mild steel welding process carries a carcinogenic risk....

  6. Sosyal Kurumlarda Din Hizmetleri Ve Sosyal Zekâ İlişkisi

    Directory of Open Access Journals (Sweden)

    Remziye Ege

    2013-06-01

    Full Text Available Bu makale sosyal zekâ çerçevesinde din hizmetleri uygulamalarının yeniden düşünülmesi konusunda bir farkındalık oluşturmayı hedeflemektedir. İlahiyat alanındaki mesleki uygulamalara odaklanarak bu uygulamalar içinde sosyal zekânın yeri tartışılmıştır. Bu bağlamda, makalede önce sosyal zekânın ne olduğu sorusu İyi Yürekli Samaryalı Meseli (Luka 10:25-37 ile ilgili bir araştırma özelinde ele alınmakta, daha sonra ise sosyal zekânın din hizmetleri uygulamaları alanındaki etkisi değerlendirilmektedir. Makalenin son bölümünde sosyal zekâyı geliştirme yolunda bazı öneriler sunulmuştur

  7. AGR steel corrosion monitoring schemes: progress on off-site testing of coupon specimens to end of 1985: Pt. 1

    International Nuclear Information System (INIS)

    Whittle, I.; Meredith, M.E.

    1988-03-01

    Off-site Advanced Gas-cooled Reactor steel corrosion monitoring through experiments on mild steel coupon specimens is reported. The appearance of all mild steel coupons oxidised over the temperature range 375 to 450 0 C is consistent with what is expected for the appropriate silicon content, temperature and in the gas mixes used. Likewise, weight gain data from the tests is as expected and where linear (breakaway) oxidation kinetics are in evidence, measured rates are within one standard deviation of the mean oxidation rates predicted by the 1/R model. Also, data relating mean breakaway oxide thickness to weight gain is in good agreement with the currently recommended relationship of 1 mg cm -2 weight gain = 6.72 μm oxide thickness. The observed oxidation behaviour of the off-site mild steel coupons is consistent with the most recent design data. (author)

  8. La caja negra de la dinámica empresarial

    Directory of Open Access Journals (Sweden)

    María Callejón

    2009-01-01

    Full Text Available Este artículo intenta aportar conocimientos sobre la contribución a la política industrial de la investigación en dinámica empresarial. Los programas de fomento a la creación de empresas se han generalizado aunque se desconoce cuál es el ritmo óptimo de creación y destrucción empresarial. El análisis económico destaca la heterogeneidad empresarial como característica dominante en la dinámica industrial. La profundización en el conocimiento de los tipos de emprendedores, su comportamiento, y su contribución diferencial a la innovación y el crecimiento permitirá ver en la "caja negra" y diseñar programas públicos adecuados. El análisis empírico realizado encuentra que la naturaleza económica del autoempleo es muy diferente de las empresas con empleados. Los programas públicos deberían priorizar entrantes con capacidad de sobrevivir y no maximizar la entrada indiscriminadamente. La supervivencia de las nuevas empresas se encuentra positivamente relacionada con su tamaño al nacer. La innovación y la inversión mejoran la supervivencia de las nuevas empresas manufactureras. La inversión en I+D aumenta el riesgo de las nuevas empresas, aunque mejore la competitividad de las empresas establecidas.

  9. La caja negra de la dinámica empresarial

    Directory of Open Access Journals (Sweden)

    María Callejón

    2009-10-01

    Full Text Available Este artículo intenta aportar conocimientos sobre la contribución a la política industrial de la investigación en dinámica empresarial. Los programas de fomento a la creación de empresas se han generalizado aunque se desconoce cuál es el ritmo óptimo de creación y destrucción empresarial. El análisis económico destaca la heterogeneidad empresarial como característica dominante en la dinámica industrial. La profundización en el conocimiento de los tipos de emprendedores, su comportamiento, y su contribución diferencial a la innovación y el crecimiento permitirá ver en la “caja negra” y diseñar programas públicos adecuados. El análisis empírico realizado encuentra que la naturaleza económica del autoempleo es muy diferente de las empresas con empleados. Los programas públicos deberían priorizar entrantes con capacidad de sobrevivir y no maximizar la entrada indiscriminadamente. La supervivencia de las nuevas empresas se encuentra positivamente relacionada con su tamaño al nacer. La innovación y la inversión mejoran la supervivencia de las nuevas empresas manufactureras. La inversión en I+D aumenta el riesgo de las nuevas empresas, aunque mejore la competitividad de las empresas establecidas.

  10. Provocarea Facebook pentru bibliotecile publice din România

    Directory of Open Access Journals (Sweden)

    Octavia-Luciana Madge

    2014-01-01

    Full Text Available Reţelele sociale şi-au câştigat rapid un loc în viaţa noastră şi în activitatea multor organizaţii şi instituţii publice şi private. La nivelul bibliotecilor, reţelele sociale şi-au demonstrat utilitatea şi rolul în calitate de instrumente de marketing pentru o mai bună comunicare cu utilizatorii. Bibliotecile publice din România au cunoscut în ultimul timp transformări mari în ceea ce priveşte modul de abordare a relaţiei cu utilizatorii şi îmbunătăţirea activităţii lor. Au lansat, de asemenea, o serie de noi servicii pentru a răspunde nevoilor comunităţii pe care o servesc şi pentru a atrage noi utilizatori. Implementarea şi utilizarea de noi aplicaţii precum reţelele de socializare online, mai exact Facebook, a fost una dintre aceste dezvoltări recente. Această lucrare analizează modul în care reţelele sociale sunt utilizate la nivelul bibliotecilor publice din România prin exemplul a trei biblioteci publice mari şi a modului în care aceste biblioteci îşi promovează serviciile prin intermediul reţelei Facebook.

  11. La importancia del diagnóstico dinámico en la práctica clínica

    Directory of Open Access Journals (Sweden)

    Roberto Anselmo Ramos Valverde

    2014-08-01

    Full Text Available El enfoque biologicista quedó teóricamente quebrantado con dos aportes fundamentales: la medicina psicosomática,que destacó la relación mente-soma como un sistema lineal de relaciones mutuas bidireccionales, señalando el papel de los factores psicológicos en la génesis de las enfermedades; y el reconocimiento por la Medicina de los factores sociales, influyentes en el proceso salud enfermedad, puente de enlace con las ciencias sociales. (1 Anteriormente el intento más acabado lo constituyeronlas series complementarias de Freud, un legado a la teoría de la causalidad y al enfoque dinámico, acercándose bastante al modelo recíproco. Una primera serie incluye los factores hereditarios y congénitos, una segunda serie constituida por las experiencias infantiles, que al interrelacionarse con la primera conforma la disposición o condición interna existente en el sujeto, la cual al interactuar con los factores desencadenantes del medio, representantes de la tercera serie,produce el efecto conductual,explicándose de esta manera el comportamiento normal y el anómalo. (1 Se trata de diagnóstico dinámico para significar el conjunto de factores etiopatogénicos biológicos, psicológicos y sociales que interactúan dialécticamente,cuyo resultado final es la enfermedad. La psicopatología, disciplina de la Psiquiatría dedicada al estudio de las causas, origen y desarrollo de los trastornos mentales, legó a la clínica psiquiátrica este modelo, que puede ser extendido a otras ramas de la medicina, para comprender al enfermo en su integridad humana y cumplir con el principio de personalizar la atención médica, al tratar enfermos, no enfermedades, sin pretender generalizar este diagnóstico como panacea heurística en la medicina clínica, donde el enfermo es la unidad básica de estudio. (1,2 El diagnóstico dinámico permite un análisis casuístico, recíproco y dialéctico, capaz de penetrar en el drama humano y descifrar las

  12. Influence of heat treatment on microstructure and properties of GX12CrMoVNbN9-1 cast steel

    Directory of Open Access Journals (Sweden)

    G. Golański

    2010-07-01

    Full Text Available The paper presents results of research on the influence of multistage heat treatment on microstructure and properties of high-chromiummartensitic GX12CrMoVNbN9 – 1 (GP91 steel. The material under investigation were samples taken out from a test coupon. Heattreatment of GP91 cast steel was performed at the parameters of temperature and time typical of treatment for multi-ton steel casts. The research has proved that in the as-received condition (as-cast state GP91 cast steel was characterized by a coarse grain, martensitic microstructure which provided the required standard mechanical properties. The heat treatment of GP91 cast steel contributed to obtainment of a fine grain microstructure of high tempered martensite with numerous precipitations of carbides of diverse size. The GP91 cast steel structure received through heat treatment made it possible to obtain high plastic properties, particularly impact strength, maintaining strength properties on the level of the required minimum.

  13. Dinâmicas de grupo orientadas pelas atividades de estudo: desenvolvimento de habilidades e competências na educação profissional

    OpenAIRE

    Alberti,Taís Fim; Abegg,Ilse; Costa,Márcia Rejane Julio; Titton,Mauro

    2014-01-01

    Explicita resultados de pesquisa sobre dinâmicas de grupo e sua contribuição para aquisição de conhecimentos teórico-práticos. Realizamos ações em uma escola pública federal, envolvendo estudantes do terceiro semestre do Curso Técnico em Administração de Empresas. Para coleta de dados, planejamos, implementamos e avaliamos sequência didática centrada em dinâmicas de grupos tematizadas pelos conteúdos curriculares. Utilizaram-se questionários abertos para avaliar se as dinâmicas de grupo poder...

  14. Unsupervised SBAS-DInSAR Processing of Space-borne SAR data for Earth Surface Displacement Time Series Generation

    Science.gov (United States)

    Casu, F.; de Luca, C.; Lanari, R.; Manunta, M.; Zinno, I.

    2016-12-01

    During the last 25 years, the Differential Synthetic Aperture Radar Interferometry (DInSAR) has played an important role for understanding the Earth's surface deformation and its dynamics. In particular, the large collections of SAR data acquired by a number of space-borne missions (ERS, ENVISAT, ALOS, RADARSAT, TerraSAR-X, COSMO-SkyMed) have pushed toward the development of advanced DInSAR techniques for monitoring the temporal evolution of the ground displacements with an high spatial density. Moreover, the advent of the Copernicus Sentinel-1 (S1) constellation is providing a further increase in the SAR data flow available to the Earth science community, due to its characteristics of global coverage strategy and free and open access data policy. Therefore, managing and storing such a huge amount of data, processing it in an effcient way and maximizing the available archives exploitation are becoming high priority issues. In this work we present some recent advances in the DInSAR field for dealing with the effective exploitation of the present and future SAR data archives. In particular, an efficient parallel SBAS implementation (namely P-SBAS) that takes benefit from high performance computing is proposed. Then, the P-SBAS migration to the emerging Cloud Computing paradigm is shown, together with extensive tests carried out in the Amazon's Elastic Cloud Compute (EC2) infrastructure. Finally, the integration of the P-SBAS processing chain within the ESA Geohazards Exploitation Platform (GEP), for setting up operational on-demand and systematic web tools, open to every user, aimed at automatically processing stacks of SAR data for the generation of SBAS displacement time series, is also illustrated. A number of experimental results obtained by using the ERS, ENVISAT and S1 data in areas characterized by volcanic, seismic and anthropogenic phenomena will be shown. This work is partially supported by: the DPC-CNR agreement, the EPOS-IP project and the ESA GEP project.

  15. Effect of boron on the hot ductility of 2.25Cr1Mo steel

    International Nuclear Information System (INIS)

    Song, S.-H.; Guo, A.-M.; Shen, D.-D.; Yuan, Z.-X.; Liu, J.; Xu, T.-D.

    2003-01-01

    The effect of boron on the hot ductility of 2.25Cr1Mo steel is investigated by means of a Gleeble 2000 thermomechanical simulator. There is a trough in the hot ductility-temperature curve, which is located between 1000 and 700 deg. C. The ductility trough shifts to lower temperatures with increasing boron content and the hot brittle range becomes shallow and narrow. In general, boron may improve the steel hot ductility in that it may retard the formation of pro-eutectoid ferrite and increase grain boundary cohesion. These effects may be related to the segregation of boron to austenite grain boundaries

  16. Corrosion of carbon steel and low-alloy steel in diluted seawater containing hydrazine under gamma-rays irradiation

    International Nuclear Information System (INIS)

    Nakano, Junichi; Yamamoto, Masahiro; Tsukada, Takashi

    2014-01-01

    Seawater was injected into reactor cores of Units 1, 2, and 3 in the Fukushima Daiichi nuclear power station as an urgent coolant. It is considered that the injected seawater causes corrosion of steels of the reactor pressure vessel and primary containment vessel. To investigate the effects of gamma-rays irradiation on weight loss in carbon steel and low-alloy steel, corrosion tests were performed in diluted seawater at 50°C under gamma-rays irradiation. Specimens were irradiated with dose rates of 4.4 kGy/h and 0.2 kGy/h. To evaluate the effects of hydrazine (N 2 H 4 ) on the reduction of oxygen and hydrogen peroxide, N 2 H 4 was added to the diluted seawater. In the diluted seawater without N 2 H 4 , weight loss in the steels irradiated with 0.2 kGy/h was similar to that in the unirradiated steels, and weight loss in the steels irradiated with 4.4 kGy/h increased to approximate 1.7 times of those in the unirradiated steels. Weight loss in the steels irradiated in the diluted seawater containing N 2 H 4 was similar to that in the diluted seawater without N 2 H 4 . When N 2 was introduced into the gas phase in the flasks during gamma-rays irradiation, weight loss in the steels decreased. (author)

  17. Loading rate effects on strength and fracture toughness of pipe steels used in Task 1 of the IPIRG program

    International Nuclear Information System (INIS)

    Marschall, C.W.; Landow, M.P.; Wilkowski, G.M.

    1993-10-01

    Material characterization tests were conducted on laboratory specimens machined from pipes to determine the effect of dynamic loading (i.e., rates comparable to those for high amplitude seismic events) on tensile properties and fracture resistance at 288 C (550 F). Specimens were fabricated from seven different pipes, including carbon steels and stainless steels (both base metal and weld metal), which were to be subjected to full-scale pipe tests in IPIRG Task 1.0. For the stainless steels tested at 288 C (550 F), tensile strength was unchanged, while yield strength and fracture resistance were increased. The increase in fracture resistance was modest for the wrought base metals and substantial for the weld metal and the cast base metal. The carbon steels tested were sensitive to dynamic strain aging, and hence the strength and toughness was affected by both temperature and strain rate effects. The carbon steel base metal and welds exhibited ultimate tensile strength values at 288 C (550 F) that were greater than at room temperature. Furthermore, the ultimate tensile strength at 288 C (550 F) was lowered significantly by increased strain rate and, in the carbon steel base metals, increased strain rate also lowered the fracture resistance, substantially in the base metal of one pipe. In comparing these results to the IPIRG pipe test results to date, it was found that the trends of these tests agree well with the Subtask 1.2 quasi-static and dynamic pipe fracture experiments. Loads measured in the Subtask 1.1 pipe experiments were, however, somewhat higher than would have been expected by the trends observed in the laboratory tests

  18. Thermal Aging Evaluation of Mod. 9Cr-1Mo Steel using Nonlinear Rayleigh Waves

    Energy Technology Data Exchange (ETDEWEB)

    Joo, Young-Sang; Kim, Hoe-Woong; Kim, Jong-Bum [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Marino, Daniel; Kim, Jin-Yeon; Jacobs, L.J [Georgia Institute of Technology, Atlanta (United States); Ruiz, Alberto [UMSNH, Morelia (Mexico)

    2014-10-15

    Thermal aging can pose a high risk to decreases in the mechanical properties such as strength or creep resistance. This can lead to an unexpected failure during long term operation. Nonlinear NDE techniques are preferred over conventional NDE techniques (linear ultrasonic measurements) because nonlinear ultrasonic techniques have shown their capability to detect a microstructural damage in the structures undergoing fatigue and creep. These nonlinear ultrasonic techniques make use of the fact that the dislocation density increases, which will create a nonlinear distortion of an ultrasonic wave; this damage causes the generation of measurable higher harmonic components in an initially mono-chromatic ultrasonic signal. This study investigates the recently developed non-contact nonlinear ultrasonic technique to detect the microstructural damage of mod. 9Cr-1Mo steel based on nonlinear Rayleigh wave with varying propagation distances. Nonlinear Rayleigh surface wave measurements using a non-contact, air-coupled ultrasonic transducer have been applied for the thermal aging evaluation of modified 9Cr-1Mo ferritic-martensitic steel. Thermal aging for various heat treatment times of mod.. 9Cr-1Mo steel specimens is performed to obtain the nucleation and growth of precipitated particles in specimens. The amplitudes of the first and second harmonics are measured along the propagation distance and the relative nonlinearity parameter is obtained from these amplitudes. The relative nonlinearity parameter shows a similar trend with the Rockwell C hardness.

  19. High yttria ferritic ODS steels through powder forging

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, Deepak [Department of Metallurgical and Materials Engineering, I.I.T-Roorkee, Uttarakhand 247667 (India); Prakash, Ujjwal, E-mail: ujwalfmt@iitr.ac.in [Department of Metallurgical and Materials Engineering, I.I.T-Roorkee, Uttarakhand 247667 (India); Dabhade, Vikram V. [Department of Metallurgical and Materials Engineering, I.I.T-Roorkee, Uttarakhand 247667 (India); Laha, K.; Sakthivel, T. [Mechanical Metallurgy Group, IGCAR, Kalpakkam, Tamilnadu 603102 (India)

    2017-05-15

    Oxide dispersion strengthened (ODS) steels are being developed for future nuclear reactors. ODS Fe-18%Cr-2%W-0.2%Ti steels with 0, 0.35, 0.5, 1 and 1.5% Y{sub 2}O{sub 3} (all compositions in weight%) dispersion were fabricated by mechanical alloying of elemental powders. The powders were placed in a mild steel can and forged in a stream of hydrogen gas at 1473 K. The steels were forged again to final density. The strength of ODS steel increased with yttria content. Though this was accompanied by a decrease in tensile elongation, all the steels showed significant ductility. The ductility in high yttria alloys may be attributed to improved inter-particle bonding between milled powders due to reduction of surface oxides by hydrogen. This may permit development of ODS steels with yttria contents higher than the conventional limit of 0.5%. It is suggested that powder forging is a promising route to fabricate ODS steels with high yttria contents and improved ductility. - Highlights: •ODS steels with yttria contents beyond the conventional limit of 0.5 wt% were fabricated by powder forging in a hydrogen atmosphere. •All the alloys exhibited significant ductility. •This may be attributed to improved inter-particle bonding due to reduction of surface oxides by hydrogen. •Strength in excess of 300 MPa was obtained at 973 K for 0.5%, 1% and 1.5% yttria ODS alloys. •Powder forging is a promising route to fabricate ODS steels and permits development of compositions with up to 1.5% yttria.

  20. Lung cancer mortality in stainless steel and mild steel welders: a nested case-referent study

    DEFF Research Database (Denmark)

    Lauritsen, Jens; Hansen, K S

    1996-01-01

    . Analysis was based on 439 deceased referents and 94 deceased cases. There was a 70% excess of lung cancer associated with "welding exposure ever" (OR +/- 95% C.I.: 1.68, 1.02-2.78). Overall OR for "mild steel (MS) welding ever" was 1.64, 0.99-2.72. The risk estimates for welding exposures showed...... an increasing tendency up to 15 years of exposure. The pattern of stainless steel (SS) welding resembles that of mild steel with an estimated OR of 1.65, 0.88-3.0. The general conclusion is that MS welding as well as SS welding seems to be associated with an increased risk of lung cancer. Further followup...

  1. Ernst Rüdin's Unpublished 1922-1925 Study "Inheritance of Manic-Depressive Insanity": Genetic Research Findings Subordinated to Eugenic Ideology.

    Science.gov (United States)

    Kösters, Gundula; Steinberg, Holger; Kirkby, Kenneth Clifford; Himmerich, Hubertus

    2015-11-01

    In the early 20th century, there were few therapeutic options for mental illness and asylum numbers were rising. This pessimistic outlook favoured the rise of the eugenics movement. Heredity was assumed to be the principal cause of mental illness. Politicians, scientists and clinicians in North America and Europe called for compulsory sterilisation of the mentally ill. Psychiatric genetic research aimed to prove a Mendelian mode of inheritance as a scientific justification for these measures. Ernst Rüdin's seminal 1916 epidemiological study on inheritance of dementia praecox featured large, systematically ascertained samples and statistical analyses. Rüdin's 1922-1925 study on the inheritance of "manic-depressive insanity" was completed in manuscript form, but never published. It failed to prove a pattern of Mendelian inheritance, counter to the tenets of eugenics of which Rüdin was a prominent proponent. It appears he withheld the study from publication, unable to reconcile this contradiction, thus subordinating his carefully derived scientific findings to his ideological preoccupations. Instead, Rüdin continued to promote prevention of assumed hereditary mental illnesses by prohibition of marriage or sterilisation and was influential in the introduction by the National Socialist regime of the 1933 "Law for the Prevention of Hereditarily Diseased Offspring" (Gesetz zur Verhütung erbkranken Nachwuchses).

  2. Fatigue and creep-fatigue in sodium of 316 1 stainless steel

    International Nuclear Information System (INIS)

    Ardellier, A.

    1982-01-01

    Equipment and results obtained on type 316 L stainless stee1 at 450 0 C and 600 0 C with low-cycle fatique and creep fatigue tests are described. Comparison with runs in air on type 316 L stainless steel shows a better low-cycle fatigue behavior in a sodium environment. This beneficial effect can be attributed to the low oxygen content which limits the surface oxidazation

  3. Semifabricate din tocătură de carne de ovină cu adaos de şrot din seminţe de nuci, dovleac, in şi struguri

    Directory of Open Access Journals (Sweden)

    Irina GRUMEZA

    2016-12-01

    Full Text Available The purpose of researches conducted in the Laboratory of Food Biotechnology of the Scientific-Practical Institute of Horticulture and Food Technology was to prepare and evaluate physico-chemical andorganoleptic properties of the semi-processed ground mutton (rolls products supplemented with walnut, pump-kin, flax and grape seed cakes (10%. The prepared semi-processed products were kept in a refrigerator at thetemperature of 0 ... + 4°C for 5 days. During 72 hours of storage in refrigeration conditions it was recorded adecrease of humidity and water-binding capacity index in roll samples. Salt and fat mass fraction changedinsignificantly and remained practically at the same level. Microbiological analyzes showed no coliform bacteria,no pathogenic bacteria, including Salmonella and sulphite reducing clostridia. Mass loss as a result of heattreatment (baking in an electric oven constituted: 9.8% (rolls with walnut seed cakes, 16.3% (pumpkin, 15.9%(grapes and 46.2% (control variant, without added cake. The best organoleptic characteristics have beenrecorded by the samples with walnut seed cake, obtaining the average score of 4.66. Rezumat. Scopul cercetărilor realizate în Laboratorul de Biotehnologii Alimentare al Institutului Ştiinţifico-Practic de Horticulturăşi Tehnologii Alimentare a fost prepararea şi evaluarea proprietăţilor fizico-chimice şiorganoleptice ale semifabricatelor din carne de ovină, îmbogăţită cu adaosuri de şrot (10% din seminţe de nuci,dovleac, in şi struguri. Semifabricatele preparate (mici au fost păstrate în frigider la 0...+40C, timp de 5zile. Peparcursul păstrării în stare refrigerată timp de 72 ore s-a constatat reducerea umidităţii şi a indicelui capacităţii delegare a apei la mostrele de mici, fracţia masică de sare şi grăsime modificându-se neesenţial şi rămânând practicla acelaşi nivel. Analizele microbiologice au arătat lipsa bacteriilor coliforme, a bacteriilor patogene

  4. The rate(time)- dependent mechanical behavior modified 9Cr-1Mo steel, 3

    International Nuclear Information System (INIS)

    Moosbrugger, J.C.

    1991-01-01

    In this paper, constitutive equations are presented for the nonisothermal small strain behavior of modified 9Cr-1Mo steel between 25degC - 600degC. The basic framework uses the superposition of nonlinear kinematic hardening rules as proposed by Chaboche and coworkes. A framework for accounting for isotropic softening is presented wherein this softening can be included in a drag stress, in a yield stress or as a decrease in the saturation level of kinematic hardening or some combination of these; a single isotropic softening equation is used as determined from experiments. The behavior of modified 9Cr-1Mo steel between 25degC - 600degC has been investigated by Swindeman, and Majors et. al. and many important features have been discussed. Here, model parameters are determined from available isothermal uniaxial data and some correlations with isothermal and nonisothermal tests are presented. (J.P.N.)

  5. Irradiation hardening of Mod.9Cr-1Mo steel

    International Nuclear Information System (INIS)

    Ryu, Woo-Seog; Kim, Sung-Ho; Choo, Kee-Nam; Kim, Do-Sik

    2009-01-01

    An irradiation test of Mod.9Cr-1Mo steel was carried out in the OR5 test hole of HANARO of a 30 MW thermal power at 390±10degC up to a fast neutron fluence of 4.4x10 19 (n/cm 2 ) (E > 1.0 MeV). The dpa of the irradiated specimens was evaluated to be 0.034 - 0.07. Tensile and impact tests of the irradiated Mod.9Cr-1Mo were done in the hot cell of the IMEF. The change of the tensile strength by irradiation was similar to the change of the yield strength. The increase of the yield and tensile strengths was up to 18% and 10% respectively. The elongation reduction of the weldment was up to 65%. (author)

  6. Effect of cold work on decarburization of 2.25Cr-1Mo steel in high temperature sodium

    International Nuclear Information System (INIS)

    Aoki, Norichika; Yoshida, Eiichi; Wada, Yusaku.

    1994-01-01

    It is known that the mechanical properties of a 2.25Cr-1Mo steel deteriorated due to the decarburization during immersion in the melt sodium at high temperatures. In low-alloy steel as well as a 2.25Cr-1Mo steel, precipitation reactions of carbides are known to be accelerated by cold working and aging. Thus, it may be expected that cold working and aging effectively suppress the decarburization of the mechanical properties of a 2.25Cr-1Mo steel because the decarburization will be restrained owing to fixation of carbon as precipitates of the carbides. In the present article, effects of cold-working and heat treatments on the kinetics of the decarburization of a 2.25Cr-1Mo steel has been studied experimentally. The annealed, cold-rolled, and normalized and tempered specimens were immersed in the melt of sodium at 500, 600 and 700degC for 425, 437 and 432h, respectively. On the basis of the observations obtained from these specimens, the experiment was also carried out at 450, 500 and 550degC for 2270 and 5465h. The microstructures before and after the immersion were observed with optical and scanning electron microscopes. An average concentration of carbon in each specimen was analyzed by an inert gas fusion method. The carbides extracted from the specimens were identified by X-ray diffraction. At immersion temperatures of 450 and 500degC, a 10% reduction of the decarburization in thickness by cold-working is sufficiently effective for retardation of the decarburization at both 2270 and 5465h. Whereas, at 550degC, more than 30% reduction in thickness by cold-working is needed for it at 2270h but even 80% reduction in thickness by cold-working causes merely slight retardation of the decarburization at 5465h. (author)

  7. Superheat effect on bainite steel hardenability

    International Nuclear Information System (INIS)

    Kubachek, V.V.; Sklyuev, P.V.

    1978-01-01

    The bainite hardenability of 34KhN1M and 35 KhN1M2Ph steels has been investigated by the end-face hardening technique. It is established that, as the temperature of austenitization rises from 900 to 1280 deg C, the temperature of bainite transformation increases and bainite hardenability of the steels falls off. A repeated slow heating to 900 deg C of previously overheated 34KhN1M steel breaks up grain, lowers the temperature of the bainite transformation and raises the hardenability to values obtained with ordinary hardening from 900 deg C. A similar heating of previously overheated 35KhN1M2Ph steel is accompanied by restoration of initial coarse grains and maintenance of both the elevated bainite transformation temperature and to lower hardenability corresponding to hardening from the temperature of previous overheating

  8. Surveying the Vienna Meridian from Brno to Varaždin

    Directory of Open Access Journals (Sweden)

    Miljenko Solarić

    2016-12-01

    Full Text Available The introduction provides a brief overview of using trigonometric chains for determining meridian arc lengths in Europe, as well as their extension to trigonometric networks in order to produce contemporary accurate maps in France. After Ruđer Bošković had visited Croatian-Hungarian Queen and Roman-German Empress Maria Theresa, she ordered Jesuit Joseph Liesganig to survey the meridian from Brno (Soběšice, over Vienna and Graz to Varaždin by establishing and surveying a trigonometric chain. That distance amounts to 320 km, i.e. the difference between latitude of the starting and finishing points of the chain equaled 2° 56' 45.85''. Two baselines were measured directly between Wiener Neustadt and Neunkirchen of 6410.903 Vienna fathom (12 158.175 m and between Seyring and Glizendorf in the Moravian field (Moravské pole, Marchfeld of 6387.862 Vienna fathom (12 114.478 m. Liesganig published previous Vienna Meridian survey results in Philosophical Transactions in London in 1768 and the final results in Latin in Dimensio Graduum Meridiani Viennensis et Hungarici in 1770. His results were quickly criticized and subsequently subjected to validation. Trigonometric point Varaždin is the first and oldest trigonometric point in Croatia.

  9. Steel making

    CERN Document Server

    Chakrabarti, A K

    2014-01-01

    "Steel Making" is designed to give students a strong grounding in the theory and state-of-the-art practice of production of steels. This book is primarily focused to meet the needs of undergraduate metallurgical students and candidates for associate membership examinations of professional bodies (AMIIM, AMIE). Besides, for all engineering professionals working in steel plants who need to understand the basic principles of steel making, the text provides a sound introduction to the subject.Beginning with a brief introduction to the historical perspective and current status of steel making together with the reasons for obsolescence of Bessemer converter and open hearth processes, the book moves on to: elaborate the physiochemical principles involved in steel making; explain the operational principles and practices of the modern processes of primary steel making (LD converter, Q-BOP process, and electric furnace process); provide a summary of the developments in secondary refining of steels; discuss principles a...

  10. Compreender o Agir Organizacional para Construção de Capacidades Dinâmicas: uma análise exploratória

    Directory of Open Access Journals (Sweden)

    Luciano Munck

    2015-08-01

    Full Text Available http://dx.doi.org/10.5007/2175-8077.2015v17n42p131 Neste estudo, de caráter bibliográfico, inter-relaciona-se as características de um fenômeno – capacidades dinâmicas – a outro fenômeno – o agir social organizacional. O objetivo é fundamentar um modelo interpretativo do processo cíclico de construção das capacidades dinâmicas pelos agentes sociais em seu agir organizacional. A partir da discussão teórica realizada, argumenta-se que os processos de ações e de decisões realizados pelos gestores em seu agir organizacional, pautando-se pelo fator ético e racional, são elementares para a construção de um processo cíclico das capacidades dinâmicas. Considerando esse argumento, questiona-se a prerrogativa de que as organizações são dependentes de recursos fixos para enfrentarem as transformações do ambiente. Para tanto, articulou-se o entendimento de que o uso das capacidades dinâmicas internalizadas nas práticas dos agentes sociais torna-se meio para se aperfeiçoar a aprendizagem organizacional oriunda dos processos decisórios. Por fim, contribui-se com a sistematização de um modelo interpretativo do processo cíclico de construção das capacidades dinâmicas pelos agentes sociais em seu agir organizacional.

  11. Helipuerto para la Escuela Superior de Medicina Hannover — Alemania Federal

    Directory of Open Access Journals (Sweden)

    Idelberger, Klaus

    1979-08-01

    Full Text Available This helicopter landing pad was built for the service of the Higher Medical School of Hannover, on top of an existing concrete car park building. The structure chosen was a fire-galvanized steel beam framework resting on pendular supports and stabilizing portal type frames. Design calculation conforms with DIN 1 055 standard. The Steel structure is completed with a foot bridge and ramp, protection rails, stairways, etc.

    La pista de aterrizaje para helicópteros, al servicio de la Escuela Superior de Medicina de Hannover, se realizó sobre un aparcamiento de hormigón ya existente. Como estructura portante se eligió un entramado de vigas de acero galvanizado al fuego sobre apoyos pendulares y pórticos estabilizantes. Los cálculos se basan en la norma DIN 1 055. La estructura de acero se completa con el puente de peatones, la rampa de peatones, las barandillas de protección, las escaleras, etcétera.

  12. Long-term Stability of 9- to 12 % Cr Steels

    DEFF Research Database (Denmark)

    Hald, John

    2004-01-01

    In the recent 25 years creep rupture strength of 9- to 12 %Cr steels for steam pipes and turbines has been doubled by development of new alloys. This development has formed a basis for improved efficiency of fossil fired steam power plants by introduction of advanced steam temperatures...... and pressures. Newly developed steam pipe steels are based on modifications of well-established steels like the X 20CrMoV12 1. Balanced addition of V, Nb and N to a 9Cr 1 Mo steel led to the Modified 9 Cr steel P 91. Addition of 1% W to a 9Cr 1 MoVNbN base composition led to steel E 911 and partial replacement...... of Mo with 1.8 % W combined with a slight amount of Boron led to steel P 92. The creep rupture strength of these new alloys are now secured with long-term tests up to 100,000 hours, which demonstrate improvements of 50% (P 91), 75 % (E 911) and 100 % (P 92) in strength compared to X 20CrMoV12 1....

  13. Effect of niobium on the embrittlement of 2.25 Cr and 2.25 Cr-1Mo steels by phosphous

    International Nuclear Information System (INIS)

    Antunes, J.L.B.

    1985-01-01

    The influence of niobium on the temper embrittlement of 2.25Cr and 2.25 Cr-1Mo steels doped with phosphorus is evaluated. The transition temperatures of the samples tempered at 650 0 C and aged at different temperatures for niobium steels. (M.J.C.) [pt

  14. Transition temperature of embrittlement of steel 11 474.1 welded joint

    International Nuclear Information System (INIS)

    Petrikova, A.; Cocher, M.

    1987-01-01

    The results are presented of tests of notch toughness in dependence on temperature for steel 11 474.1 used for the manufacture of steam separators, in the area of a joint welded using an automatic submerged-arc welding machine with pre-heating at 200 to 250 degC. After welding, the welded joints were annealed for reduced stress for 160 minutes at a temperature of 600 to 650 degC and left to cool off in the furnace. The obtained results show that: (1) critical embrittlement temperature for the welded joint and the given welding technology ranges within -20 and -13 degC; (2) critical embrittlement temperature following heat ageing is shifted to positive temperature values; (3) pressure tests of the steam separator jacket made of steel 11 474.1 may in the process of production be carried out at a minimal wall temperature of 17 degC; (4) in case a pressure test has to be made after the equipment has been in operation for a certain period of time the test will probably have to be made at temperatures higher than 20 degC; (5) further tests will have to be made at temperatures higher than 20 degC in order to determine critical embrittlement temperatures after ageing. (J.B.). 7 figs., 2 tabs., 5 refs

  15. High yttria ferritic ODS steels through powder forging

    Science.gov (United States)

    Kumar, Deepak; Prakash, Ujjwal; Dabhade, Vikram V.; Laha, K.; Sakthivel, T.

    2017-05-01

    Oxide dispersion strengthened (ODS) steels are being developed for future nuclear reactors. ODS Fe-18%Cr-2%W-0.2%Ti steels with 0, 0.35, 0.5, 1 and 1.5% Y2O3 (all compositions in weight%) dispersion were fabricated by mechanical alloying of elemental powders. The powders were placed in a mild steel can and forged in a stream of hydrogen gas at 1473 K. The steels were forged again to final density. The strength of ODS steel increased with yttria content. Though this was accompanied by a decrease in tensile elongation, all the steels showed significant ductility. The ductility in high yttria alloys may be attributed to improved inter-particle bonding between milled powders due to reduction of surface oxides by hydrogen. This may permit development of ODS steels with yttria contents higher than the conventional limit of 0.5%. It is suggested that powder forging is a promising route to fabricate ODS steels with high yttria contents and improved ductility.

  16. Optimum conditions for aging of stainless maraging steels

    International Nuclear Information System (INIS)

    Mironenko, P.A.; Krasnikova, S.I.; Drobot, A.V.

    1980-01-01

    Aging kinetics of two 0Kh11N10M2T type steels in which 3 % Mo (steel 1), and 3 % Mo and 11 % Co (steel 2) had been additionally introduced instead of titanium were investigated. Electron microscopy and X-ray methods were used. It was ascertained that the process of steel aging proceeded in 3 stages. Steel 2 was hardened more intensively during the aging, had a higher degree of hardness and strength after the aging, weakened more slowly if overaged than steel 1. The intermetallide hcp-phase Fe 2 Mo was the hardening phase on steels extended aging. Optimum combination of impact strength and strength was was achieved using two-stage aging: the first stage - maximum strength aging was achieved, the second stage - aging at minimum temperatures of two-phase α+γ region

  17. Low-cyclic fatigue behavior of modified 9Cr–1Mo steel at elevated temperature

    Energy Technology Data Exchange (ETDEWEB)

    Guguloth, Krishna; Sivaprasad, S. [CSIR-National Metallurgical laboratory, Material Science and Technology Division, Jamshedpur 831007 (India); Chakrabarti, D. [Department of Metallurgical and Materials Engineering, Indian Institute of Technology, Kharagpur 721302 (India); Tarafder, S. [CSIR-National Metallurgical laboratory, Material Science and Technology Division, Jamshedpur 831007 (India)

    2014-05-01

    The low-cycle fatigue behavior of indigenously developed modified 9Cr–1Mo steel has been evaluated using a constant strain rate (1×10{sup −3} s{sup −1}) at ambient temperature (25 °C) and at elevated temperatures (500–600 °C) over the strain amplitudes varying between ±0.7% and ±1.2%. Cyclic stress response showed a gradual softening regime that ended in a stress plateau until complete failure of the specimens. The estimated fatigue life decreased with the increase in test temperature. The effect of temperature on fatigue life was more pronounced at lower strain amplitudes. The cyclic deformation behavior at different temperatures has been analyzed from hysteresis loop and also in view of the changes taking place in dislocation structure and dislocation–precipitation interaction. Evaluation of low-cycle fatigue properties of modified 9Cr–1Mo steel over a range of test temperature can help in designing components for in-core applications in fast breeder reactors and in super heaters for nuclear power plants.

  18. Steel alloys

    International Nuclear Information System (INIS)

    Bloom, E.E.; Stiegler, J.O.; Rowcliffe, A.F.; Leitnaker, J.M.

    1977-01-01

    The invention deals with a fuel element for fast breeder reactors. It consits essentially of a uranium oxide, nitride, or carbide or a mixture of these fuels with a plutonium or thorium oxide, nitride, or carbide. The fuel elements are coated with an austenitic stainless steel alloy. Inside the fuel elements, vacancies or small cavities are produced by neutron effects which causes the steel coating to swell. According to the invention, swelling is prevented by a modification of type 304, 316, 321, or 12 K 72HV commercial steels. They consist mainly of Fe, Cr, and Ni in a ratio determined by a temary diagram. They may also contain 1.8 to 2.3% by weight of Mo and a fraction of Si (0.7 to 2% by weight) and Ti(0.10 to 0.5% by weight) to prevent cavity formation. They are structurally modified by cold working. (IHOE) [de

  19. Adaptation of the pressure test for borehole heat exchangers in accordance with DIN V 4279-7; Anpassen der Druckpruefung nach DIN V 4279-7 fuer Erdwaermesonden aus Polyethylen

    Energy Technology Data Exchange (ETDEWEB)

    Rohner, E.

    2005-07-01

    The goal of this project was to develop a pressure test in accordance with DIN V 4279-7 to identify possible leakages of borehole heat exchanger systems. The presented pressure test serves predominantly as quality assurance. The test shall prevent that leaking borehole heat exchangers are put into operation. Since January 1{sup st}, 2005 the test, based on this report, is integral part of the seal of approval 'Erdwaermesonde' delivered by the Association for the Promotion of Heat Pumps in Switzerland ('Foerdergemeinschaft Waermepumpen Schweiz'). The presented methodology allows accurate and fast measurements of the tightness of borehole heat exchanger systems (test duration: about 1.5 h). A measuring apparatus was developed which allows to proceed easily with the pressure test. Pressure test and measuring apparatus have been already successfully used. (author)

  20. Impression creep behaviour of Mod. 9Cr-1Mo steel weld joints

    International Nuclear Information System (INIS)

    Ridhin Raj, V.R.; Kottda, Ravi Sankar; Kamaraj, M.; Maduraimuthu, V.M.; Vasudevan, M.

    2016-01-01

    P91 steel (9Cr-1Mo) steel is extensively used in power plants for super heater coils, headers and steam piping. The aim of the present work is to study the creep behaviour of different zones of A-TIG weld joint using impression creep technique and compare it with that of the TIG weld joint. P91 steel weld joints were made by A-TIG welding without using any filler material and multi-pass TIG welding is done using ER90S-B9 filler rods. Welds were subjected to post-weld heat treatment (PWHT). Impression creep tests were carried out at 650 °C on the base metal, weld metal and HAZ regions. Optical Microscope and TEM were used to correlate microstructures with observed creep rates. The FGHAZ showed significantly higher impression creep rate compared to that of the base metal and weld metal. Fine grain size and relatively coarser M 23 C 6 carbide particles are responsible for higher creep rate. The impression creep rate of A-TIG weld metal and coarse grain HAZ was found to be lower than that of base metal. This is attributed to the higher grain size in weld metal and coarse HAZ attributed to the higher grain size in weld metal and to the higher peak temperature observed during A-TIG welding. (author)

  1. Categoria etnică din perspectivă lingvistică

    Directory of Open Access Journals (Sweden)

    Răzvan Săftoiu

    2017-03-01

    Full Text Available În această lucrare, propun analiza din perspectivă lingvistică a construcției unei categorii etnice din România care este denumită prin cel puțin doi termeni: țigan și rom. Conceptul de categorie se referă la membrii unui anumit grup care se diferențiază de alte grupuri printr-un set de elemente specifice recunoscute la nivelul unei comunități mai largi. În interacțiune, indivizii apelează frecvent la categorii și la setul de trăsături pe care îl poartă o anumită categorie, deoarece este mai ușor de operat cu seturi de cunoștințe decît cu referințe pentru fiecare individ în parte. Analiza are la bază o serie de expresii și locuțiuni, proverbe și glume care au circulat (sau încă mai circulă în spațiul românesc și care au conturat, la nivelul mentalității colective, imaginea unei categorii etnice a cărei denumire (încă oscilează între doi termeni. Textele au fost grupate în funcție de diverse stereotipuri asociate categoriei etnice avute în vedere, evidențiind conotațiile peiorative ale utilizărilor termenului țigan în raport cu categoria etnică rom, o categorie „goală” de semnificație, care poate fi „umplută” cu elemente ce pot creiona o imagine pozitivă.

  2. "We're still in a struggle": Diné resilience, survival, historical trauma, and healing.

    Science.gov (United States)

    Goodkind, Jessica R; Hess, Julia Meredith; Gorman, Beverly; Parker, Danielle P

    2012-08-01

    As part of a community/university collaborative effort to promote the mental health and well-being of Diné (Navajo) youth, we explored the relevance of addressing historical trauma and current structural stressors, and of building on individual and community strengths through healing and social transformation at multiple levels. Qualitative analyses of 74 ethnographic interviews with 37 Diné youth, parents, and grandparents suggested that a focus on historical trauma as a conceptual frame for behavioral health inequities, understood within the context of resilience and survival, is appropriate. Our findings also highlight the salience of current stressors such as poverty and violence exposure. We explore the fit of an historical trauma healing framework and present implications for intervention and transformation through revitalization of traditional knowledge, culturally based healing practices, intergenerational education, and social change strategies designed to eliminate social inequities.

  3. Impact properties of 2 1/4 Cr--1 Mo steel after ten years EBR-II service

    International Nuclear Information System (INIS)

    Shields, J.A.; Server, W.L.; Sheckherd, J.W.; Longua, K.J.

    1976-01-01

    The material studied in this investigation was obtained from a 2 1 / 4 Cr--1 Mo steel superheated steam line which had been in service for approximately 90,000 hours. Of that 90,000 hours, approximately 40,000 hours were at a temperature of approximately 820 0 F and a pressure of 1250 psi, and 35,000 hours were at a temperature of 500 0 F and 1250 psi. The results of optical metallography and instrumented impact testing performed on the materials are presented

  4. PRODUCEREA ŞI COMERCIALIZAREA BĂUTURILOR ALCOOLICE ÎN ORAŞELE DIN RZECZPOSPOLITA ŞI ŢARA MOLDOVEI (SEC.XVI-XVII

    Directory of Open Access Journals (Sweden)

    Nicolae DUDNICENCO

    2016-12-01

    Full Text Available Articolul vizează producerea, comercializarea şi consumul băuturilor alcoolice în oraşele din Rzeczpospolita (a berii, a votcii, a miedului şi din Ţara Moldovei (a vinului, a rachiului, a berii, a brăgii în sec. XVI-XVII. Se investighează mo­dul de producere, comercializare, precum şi taxele care se percepeau pentru băuturile alcoolice în oraşele din teri­toriul dat. Producerea băuturilor alcoolice aducea venituri mari economiei oraşelor din spaţiul indicat supra.PRODUCTION AND COMMERCIALISATION OF ALCOHOLIC DRINKS IN RZECZPOSPOLITA AND MOLDOVA PRINCIPALITY CITIES (XVI-XVII C.The article targeting the production, marketing and consumption of alcoholic drinks in the cities from Rzeczpospolita (beer, vodka, mead and from Moldova (wine, spirits, beer, braga in the XVI-XVII c. It have been investigated the mode of production, sell and taxes at which were subjected the alcoholic drinks in the cities on that territory. Production of alcoholic drinks brought substantial revenues to the economy of the cities from the indicated area.

  5. Diversidad y dinámica de un bosque subandino de altitud en la región norte de los Andes colombianos

    Directory of Open Access Journals (Sweden)

    Jesús Oswaldo Velásquez Restrepo

    2012-06-01

    Full Text Available Los bosques sub-Andinos poseen alta diversidad biológica, de los cuales poco se conoce sobre su dinámica natural. Se evaluaron patrones de diversidad y biomasa, tasas de mortalidad y reclutamiento en dos parcelas permanentes de una hectárea cada una, establecidas en bosques en altitudes entre los 2 000-2 200msnm, en la vertiente Oriental de la cordillera Occidental del norte de los Andes en Colombia. Se determino diversidad de especies mediante el índice alpha de Fisher, la dinámica del bosque se evaluó mediante tres censos durante nueve anos. En total, se hallaron 1 964 individuos con un diámetro a la altura del pecho DAP≥10cm. pertenecientes a 222 especies, 113 géneros y 60 familias. La riqueza media de especies fue de 156 especies por hectárea y un índice alpha medio de Fisher de 56.2/h. Las tasas de mortalidad y reclutamiento fueron de 0.88% y 1.16% respectivamente, lo cual no indica que se presente un efecto externo proveniente del calentamiento global sobre la dinámica del bosque. La biomasa aérea promedio fue de 243.44±9.82tn/ha con un incremento anual promedio de 2.9ton/ha, valor superior a los reportados, lo cual sugiere que el equilibrio para este bosque no se ha alcanzado. De acuerdo con las observaciones de campo, este bosque parece estar recuperándose de una alteración pasada.

  6. Development of ferritic steels for fusion reactor applications

    Energy Technology Data Exchange (ETDEWEB)

    Klueh, R.L.; Maziasz, P.J.; Corwin, W.R.

    1988-08-01

    Chromium-molybdenum ferritic (martensitic) steels are leading candidates for the structural components for future fusion reactors. However, irradiation of such steels in a fusion environment will produce long-lived radioactive isotopes that will lead to difficult waste-disposal problems. Such problems could be reduced by replacing the elements in the steels (i.e., Mo, Nb, Ni, N, and Cu) that lead to long-lived radioactive isotopes. We have proposed the development of ferritic steels analogous to conventional Cr-Mo steels, which contain molybdenum and niobium. It is proposed that molybdenum be replaced by tungsten and niobium be replaced by tantalum. Eight experimental steels were produced. Chromium concentrations of 2.25, 5, 9, and 12% were used (all concentrations are in wt %). Steels with these chromium compositions, each containing 2% W and 0.25% V, were produced. To determine the effect of tungsten and vanadium, 2.25 Cr steels were produced with 2% W and no vanadium and with 0.25% V and O and 1% W. A 9Cr steel containing 2% W, 0.25 V, and 0.07% Ta was also studied. For all alloys, carbon was maintained at 0.1%. Tempering studies on the normalized steels indicated that the tempering behavior of the new Cr-W steels was similar to that of the analogous Cr-Mo steels. Microscopy studies indicated that 2% tungsten was required in the 2.25 Cr steels to produce 100% bainite in 15.9-mm-thick plate during normalization. The 5Cr and 9Cr steels were 100% martensite, but the 12 Cr steel contained about 75% martensite with the balance delta-ferrite. 33 refs., 35 figs., 5 tabs.

  7. Development of ferritic steels for fusion reactor applications

    International Nuclear Information System (INIS)

    Klueh, R.L.; Maziasz, P.J.; Corwin, W.R.

    1988-08-01

    Chromium-molybdenum ferritic (martensitic) steels are leading candidates for the structural components for future fusion reactors. However, irradiation of such steels in a fusion environment will produce long-lived radioactive isotopes that will lead to difficult waste-disposal problems. Such problems could be reduced by replacing the elements in the steels (i.e., Mo, Nb, Ni, N, and Cu) that lead to long-lived radioactive isotopes. We have proposed the development of ferritic steels analogous to conventional Cr-Mo steels, which contain molybdenum and niobium. It is proposed that molybdenum be replaced by tungsten and niobium be replaced by tantalum. Eight experimental steels were produced. Chromium concentrations of 2.25, 5, 9, and 12% were used (all concentrations are in wt %). Steels with these chromium compositions, each containing 2% W and 0.25% V, were produced. To determine the effect of tungsten and vanadium, 2.25 Cr steels were produced with 2% W and no vanadium and with 0.25% V and O and 1% W. A 9Cr steel containing 2% W, 0.25 V, and 0.07% Ta was also studied. For all alloys, carbon was maintained at 0.1%. Tempering studies on the normalized steels indicated that the tempering behavior of the new Cr-W steels was similar to that of the analogous Cr-Mo steels. Microscopy studies indicated that 2% tungsten was required in the 2.25 Cr steels to produce 100% bainite in 15.9-mm-thick plate during normalization. The 5Cr and 9Cr steels were 100% martensite, but the 12 Cr steel contained about 75% martensite with the balance delta-ferrite. 33 refs., 35 figs., 5 tabs

  8. Doctor Shoja-ad-Din Sheikholeslamzadeh and his Achievements

    Directory of Open Access Journals (Sweden)

    Ahmadreza Afshar

    2015-01-01

    Full Text Available Doctor Shoja-ad-Din Sheikholeslamzadeh (also known as Dr. Sheikh (1931-2014 was an outstanding orthopedic surgeon. He is credited for the establishment of the Iranian Association of Rehabilitation, Shafa Yahyaian Hospital as an Orthopedic and Rehabilitation Center, the Social Welfare Organization, Iran’s emergency dispatch center (115 and many other major projects that led to the upgrading of health care services in Iran. He also served as the Minister of Social Welfare and Minister of Health and Welfare before the Islamic revolution. The history of modern health care management and modern orthopedic surgery in Iran are indebted to the great leadership and executive abilities of Dr. Sheikh

  9. Dinámica y control poblacional de insectos

    OpenAIRE

    Anabel Albornoz, Teresita

    2012-01-01

    Anais do I Encontro de Iniciação Científica e de Extensão da Unila - Sessão de Ciências Biológicas. Dia 05/06/12 - 08h00 às 12h00, Unila-Centro - Sala 14 - 3o Piso El presente proyecto de investigación trata de la dinámica poblacional de insectos, la relación com depre - dadores y la interacción de ambos con plantaciones de frutas. El objetivo es buscar el realismo en la fór - mula predador-presa, en relación al tiempo y al espacio, según Lotka-Volterra. Esto significa, encontrar ...

  10. Doctor Shoja-ad-Din Sheikholeslamzadeh and his Achievements.

    Science.gov (United States)

    Afshar, Ahmadreza; Ziaei, Majid Eyvaz; Ahmadi, Aziz

    2015-01-01

    Doctor Shoja-ad-Din Sheikholeslamzadeh (also known as Dr. Sheikh) (1931-2014) was an outstanding orthopedic surgeon. He is credited for the establishment of the Iranian Association of Rehabilitation, Shafa Yahyaian Hospital as an Orthopedic and Rehabilitation Center, the Social Welfare Organization, Iran's emergency dispatch center (115) and many other major projects that led to the upgrading of health care services in Iran. He also served as the Minister of Social Welfare and Minister of Health and Welfare before the Islamic revolution. The history of modern health care management and modern orthopedic surgery in Iran are indebted to the great leadership and executive abilities of Dr. Sheikh.

  11. Corrosion inhibition efficiency of linear alkyl benzene derivatives for carbon steel pipelines in 1M HCl

    Directory of Open Access Journals (Sweden)

    A.M. Al-Sabagh

    2011-06-01

    Full Text Available Linear alkyl benzene sulfonic acid (L and three of its ester derivatives (L1, L2, L3 were prepared, followed by quaternization of these esters (L1Q, L2Q, L3Q. The corrosion inhibition effect on carbon steel in 1 M HCl was studied using weight loss and potentiodynamic polarization measurements. The adsorption of the inhibitors on carbon steel surface obeyed the Langmuir’s adsorption isotherm. The associated activation energy of corrosion and other thermodynamic parameters such as enthalpy (ΔH∗, entropy (ΔS∗ of activation, adsorption–desorption equilibrium constant (Kads, standard free energy of adsorption (ΔGoads, heat (ΔHoads, and entropy of adsorption (ΔSoads were calculated to elaborate the corrosion inhibition mechanism.

  12. Automated Steel Cleanliness Analysis Tool (ASCAT)

    Energy Technology Data Exchange (ETDEWEB)

    Gary Casuccio (RJ Lee Group); Michael Potter (RJ Lee Group); Fred Schwerer (RJ Lee Group); Dr. Richard J. Fruehan (Carnegie Mellon University); Dr. Scott Story (US Steel)

    2005-12-30

    The objective of this study was to develop the Automated Steel Cleanliness Analysis Tool (ASCATTM) to permit steelmakers to evaluate the quality of the steel through the analysis of individual inclusions. By characterizing individual inclusions, determinations can be made as to the cleanliness of the steel. Understanding the complicating effects of inclusions in the steelmaking process and on the resulting properties of steel allows the steel producer to increase throughput, better control the process, reduce remelts, and improve the quality of the product. The ASCAT (Figure 1) is a steel-smart inclusion analysis tool developed around a customized next-generation computer controlled scanning electron microscopy (NG-CCSEM) hardware platform that permits acquisition of inclusion size and composition data at a rate never before possible in SEM-based instruments. With built-in customized ''intelligent'' software, the inclusion data is automatically sorted into clusters representing different inclusion types to define the characteristics of a particular heat (Figure 2). The ASCAT represents an innovative new tool for the collection of statistically meaningful data on inclusions, and provides a means of understanding the complicated effects of inclusions in the steel making process and on the resulting properties of steel. Research conducted by RJLG with AISI (American Iron and Steel Institute) and SMA (Steel Manufactures of America) members indicates that the ASCAT has application in high-grade bar, sheet, plate, tin products, pipes, SBQ, tire cord, welding rod, and specialty steels and alloys where control of inclusions, whether natural or engineered, are crucial to their specification for a given end-use. Example applications include castability of calcium treated steel; interstitial free (IF) degasser grade slag conditioning practice; tundish clogging and erosion minimization; degasser circulation and optimization; quality assessment/steel

  13. Automated Steel Cleanliness Analysis Tool (ASCAT)

    International Nuclear Information System (INIS)

    Gary Casuccio; Michael Potter; Fred Schwerer; Richard J. Fruehan; Dr. Scott Story

    2005-01-01

    The objective of this study was to develop the Automated Steel Cleanliness Analysis Tool (ASCATTM) to permit steelmakers to evaluate the quality of the steel through the analysis of individual inclusions. By characterizing individual inclusions, determinations can be made as to the cleanliness of the steel. Understanding the complicating effects of inclusions in the steelmaking process and on the resulting properties of steel allows the steel producer to increase throughput, better control the process, reduce remelts, and improve the quality of the product. The ASCAT (Figure 1) is a steel-smart inclusion analysis tool developed around a customized next-generation computer controlled scanning electron microscopy (NG-CCSEM) hardware platform that permits acquisition of inclusion size and composition data at a rate never before possible in SEM-based instruments. With built-in customized ''intelligent'' software, the inclusion data is automatically sorted into clusters representing different inclusion types to define the characteristics of a particular heat (Figure 2). The ASCAT represents an innovative new tool for the collection of statistically meaningful data on inclusions, and provides a means of understanding the complicated effects of inclusions in the steel making process and on the resulting properties of steel. Research conducted by RJLG with AISI (American Iron and Steel Institute) and SMA (Steel Manufactures of America) members indicates that the ASCAT has application in high-grade bar, sheet, plate, tin products, pipes, SBQ, tire cord, welding rod, and specialty steels and alloys where control of inclusions, whether natural or engineered, are crucial to their specification for a given end-use. Example applications include castability of calcium treated steel; interstitial free (IF) degasser grade slag conditioning practice; tundish clogging and erosion minimization; degasser circulation and optimization; quality assessment/steel cleanliness; slab, billet

  14. Mechanics in Steels through Microscopy

    NARCIS (Netherlands)

    Tirumalasetty, G.K.

    2013-01-01

    The goal of the study consolidated in this thesis is to understand the mechanics in steels using microscopy. In particular, the mechanical response of Transformation Induced Plasticity (TRIP) steels is correlated with their microstructures. Chapter 1 introduces the current state of the art of TRIP

  15. Fatigue Resistance of GX12CrMoVNbN9-1 Cast Steel after Ageing Process

    Directory of Open Access Journals (Sweden)

    Stanisław MROZIŃSKI

    2014-12-01

    Full Text Available In the present paper, low cycle fatigue behaviour of GX12CrMoVNbN9-1 (GP91 cast steel is presented. Fatigue tests were performed under isothermal conditions at room temperature and at 550 and 600oC, on five levels of total strain amplitude value ɛac = 0.25÷0.60%. The cast steel subject to investigation was in the as-received condition (after heat treatment and after 8000 hours of ageing at the temperature of 600oC. Performed research has shown an insignificant influence of the ageing process on mechanical properties of GP91 cast steel, determined with the static test of tension. Analysis of the performed tests has proved that GP91 cast steel in the as-received condition and after ageing process was characterized by strong cyclic softening without a clear period of stabilization of the hysteresis loop parameters. The fatigue lifetime curves at each temperature were obtained based on Basquin and Coffin – Manson equations. The process of ageing of GP91 cast steel contributed to a decrease in its fatigue life Nf from a few to a few dozen percent, and the level of fatigue life was dependent on the value of strain amplitude ɛac. It has also been stated that the fatigue life Nf of GP91 cast steel is determined by its plastic properties, and the degree of changes in fatigue life Nf was dependent not only on the temperature of testing, but also on the value of strain amplitude ɛac. DOI: http://dx.doi.org/10.5755/j01.ms.20.4.6077

  16. Comparative Analysis of Welded and Adhesive Joints Strength Made of Acid-Resistant Stainless Steel Sheets

    Directory of Open Access Journals (Sweden)

    Izabela Miturska

    2017-12-01

    Full Text Available The article presents the selected results of strength tests on the effectiveness of bonding high-alloy steel 1.4310. Sheet steel is one of the materials that are difficult to activate energy. Effective joining of it is difficult, requires selection of the appropriate bonding technology. The paper focuses on the comparative tests the shear strength of one-single lap welded and bonded joints. The welding process was performed 3 groups of samples TIG welding and argon, where the variable value of the welding process was current: 60A, 70A, 80A. The adhesion process was performed in 6 groups of samples which differed in the method of surface preparation and the type of the adhesive. Adhesive joints were made by using adhesive of epoxy resin and a hardener: Epidian 61/TFF at a mass ratio of 100:22 and Epidian 61/IDA at a mass ratio of 100:40. As a way of surface preparation applied 3 different, but simplified and environmentally friendly methods of surface preparation: degreasing with using cleaner Loctite 7061, abrasive machining with P320 and degreasing and grinding with abrasive T800 and degreasing were used. Make joints and curing the adhesive joints were carried out at ambient temperature. Analyzed the joints were tested destructive - which set out the shear strength, in accordance with DIN EN 1465 on the testing machine Zwick / Roell Z150. Based on the results of research it was found that better results were obtained for the maximum welded joints, but this result was similar to the maximum value of the strength of the adhesive bond.

  17. Medidas dinámicas de predictibilidad en el índice s&p 500 y sus determinantes

    Directory of Open Access Journals (Sweden)

    Javier Humberto Ospina Holguín

    2015-04-01

    Full Text Available El objeto de este estudio es medir la predictibilidad del índice accionario estadounidense S&P 500 y establecer posibles determinantes de esta predictibilidad. La predictibilidad se ha estudiado ampliamente, pero en pocos casos mediante medidas dinámicas y per se, como se hace aquí. Para establecer la predictibilidad se utilizan la medida eta del campo de las redes neuronales, el valor p del test de la razón de varianzas del campo de la econometría financiera y el análisis de fluctuación sin tendencia del campo de la econofísica. Se construye un algoritmo de inversión basado en las medidas dinámicas de predictibilidad que es mejor que la estrategia de comprar y mantenerse en el periodo estudiado. Para la medida más promisoria, se establece una relación empírica entre la predictibilidad y varios factores económicos y financieros. El panorama que arroja este estudio es el de un mercado que no es estáticamente predecible, sino cuya predictibilidad evoluciona dinámicamente en el tiempo, lo cual es compatible con la hipótesis del mercado adaptativo.

  18. Instrumentos de avaliação da postura dinâmica: aplicabilidade ao ambiente escolar

    Directory of Open Access Journals (Sweden)

    Matias Noll

    Full Text Available INTRODUÇÃO: Para que a avaliação da postura dinâmica seja efetivada é necessário, primeiramente, conhecer os diversos instrumentos, disponíveis e validados na literatura, apropriados para esse fim. OBJETIVO: O objetivo deste artigo de revisão sistemática foi descrever, sintetizar e analisar criticamente os instrumentos encontrados na literatura que objetivem avaliar a postura dinâmica, tanto em adultos quanto em escolares, e refletir sobre a possibilidade de utilização desses métodos no ambiente escolar. MATERIAIS E MÉTODOS: Foi realizada uma busca sistemática de artigos em bases de dados (Scopus, ScienceDirect, PubMed, SciELO publicados a partir da década de 1980 e no Banco de Teses e Dissertações da Capes. As palavras-chave utilizadas na busca pelos artigos foram back, spine, back injuries, school, back school, postural hygiene program, education, child, student, posture, em combinação com as palavras-chave evaluation, assessment, measurement, e os respectivos termos em português. Os instrumentos propostos deveriam preencher os seguintes critérios: (a avaliar a postura corporal durante a realização de atividades da vida diária (AVDs; (b utilizar critérios pré-definidos de avaliação da postura dinâmica; e (c avaliar a postura a partir de observação, direta ou a partir de filmagem. RESULTADOS: Foram identificados oito artigos originais que apresentam instrumentos de avaliação da postura dinâmica, avaliando a execução de AVDs a partir de critérios biomecânicos pré-definidos por escalas numéricas; destes, apenas quatro instrumentos foram elaborados com o propósito de avaliar a execução de AVDs de escolares. CONSIDERAÇÕES FINAIS: Em geral, os instrumentos apresentam algumas limitações metodológicas, embora sejam de fácil aplicabilidade.

  19. STUDIUL COMPLEX Al ULEIULUI VOLATIL DIN SPECIA PEROVSCHIA ATRIPLICIFOLIA BENTH.

    Directory of Open Access Journals (Sweden)

    Maricica COLŢUN

    2017-07-01

    Full Text Available În lucrare sunt prezentate rezultatele unui studiu vast privind biologia, compoziția chimică, fitochimia cantitativă și calitativă a uleiului volatil din specia Perovskia atriplicifolia, care se comportă ca plantă perenă, erbacee din familia Lamiaceae. În R. Moldova nu este cercetată ca plantă aromatică şi medicinală. Are o plasticitate ecologică mare, nu are cerinţe deosebite faţă de factorii climaterici. Se utilizează pentru proprietăţile sale febrifuge, în medicină – pentru scăderea febrei, deține proprietăți culinare dar şi decorative ori de purificare a aerului.THE COMPLEX STUDY OF THE ESSENTIAL OIL OF THE SPECIESPEROVSCHIA ATRIPLICIFOLIA BENTH.The paper presents the results of a vast study on the biology, chemical composition and qualitative phytochemistry of the essential oil of the species Perovskia atriplicifolia, which behaves like a perennial, herbaceous plant in the Lamiaceae family. In theRepublic ofMoldova, it has not been investigated as an aromatic and medicinal plant. It has a high ecological plasticity and no special requirements to climatic factors. It has febrifuge properties and is used in medicine to reduce fever. Besides, this plant is used for culinary, ornamental purposes and for air purification.

  20. Metodología integral y dinámica aplicada a la programación y control de proyectos

    Directory of Open Access Journals (Sweden)

    Leonardo José Gonzalez

    2012-01-01

    Full Text Available Este trabajo presenta la aplicación de la metodología integral y dinámica en la programación y control dinámico de proyectos. Para esto, a partir de la metodología se desarrolla un modelo que combina redes de actividad AON (actividad en el nodo bajo los supuestos CPM, ejecución multimodo y dinámica de sistemas. El modelo se operacionaliza por medio del desarrollo de una red de programación y una red de ejecución que interactúan a través de un bucle de control. La propuesta se valida utilizando las redes de 16 actividades de la librería MRCPSP de PSPLIB. El modelo derivado de la metodología presenta ventajas significativas en los indicadores característicos en gestión de proyectos. El trabajo concluye con la propuesta de nuevas combinaciones de herramientas, que unidas a la metodología permiten abordar problemas de programación y control de proyectos con mayor variabilidad y complejidad.

  1. Entropía proporcional de la dinámica cardiaca aplicada al diagnóstico de pacientes de la Unidad de Cuidados Intensivos

    Directory of Open Access Journals (Sweden)

    Javier Rodríguez

    2013-03-01

    Full Text Available La teoría de sistemas dinámicos cuantifica los estados y la evolución de los sistemas. Con base en esta teoría se creó una nueva metodología que cuantifica parejas ordenadas de frecuencias cardiacas en el espacio de fases de mediante la probabilidad y proporciones de la entropía, diferenciando clínicamente normalidad, enfermedad crónica, aguda, y evolución. Se registraron frecuencias cardiacas y latidos totales cada hora en 40 Holter de pacientes hospitalizados en la Unidad de Cuidados Coronarios, se realizó una simulación computacional para construir atractores caóticos y se evaluó la probabilidad, la entropía no equiprobable, y las proporciones de la entropía para la ocupación espacial de cada atractor, realizando comparaciones entre el diagnóstico clínico y el obtenido a través de la metodología físico matemática. Se evidenció que la metodología detecta en todos los casos el estado patológico de la dinámica, obteniendo valores de sensibilidad y especificidad de 100% y coeficiente Kappa de 1, evidenciando que es posible además establecer cuantitativamente la gravedad del mismo. Los resultados confirman que la autoorganización física y matemática de la dinámica cardiaca reflejada en el atractor dinámico geométrico, permite establecer predicciones de aplicación clínica en pacientes de la Unidad de Cuidados Coronarios.

  2. Modelizaciones Dinámicas en Matemáticas. Usos del Geogebra

    Directory of Open Access Journals (Sweden)

    Isabel Álvarez García-Mon

    2012-04-01

    Full Text Available El CD-ROM “Modelizaciones Dinámicas en Matemáticas. Usos del GeoGebra” es un material destinado a profesores de Matemáticas de Educación Secundaria y Bachillerato. Consta de once proyectos diferentes sobre modelización matemática, en los que, utilizando el software GeoGebra, se resuelven problemas matemáticos basados en situaciones del mundo real.

  3. Osservazione dei fenomeni deformativi nel centro di Roma. Dall'applicazione di tecniche avanzate DInSAR, all'analisi qualitativa della natura del rumore dei dati COSMO Sky-Med

    OpenAIRE

    Massimo Morigi

    2015-01-01

    This work was created to focus the attention on a particular aspect of theequivocation (aliasing) of the measurements made with Differential SAR interferometry (DInSAR) X-band for the presence of snow. Such equivocationemerge after a careful interpretation of the results obtained through theapplication of techniques Advanced DInSAR (A-DInSAR) for the observation ofthe deformation phenomena of the monumental structures in the center ofRome. The qualitative analysis have enabled the identificat...

  4. The Parallel SBAS-DInSAR algorithm: an effective and scalable tool for Earth's surface displacement retrieval

    Science.gov (United States)

    Zinno, Ivana; De Luca, Claudio; Elefante, Stefano; Imperatore, Pasquale; Manunta, Michele; Casu, Francesco

    2014-05-01

    Differential Synthetic Aperture Radar Interferometry (DInSAR) is an effective technique to estimate and monitor ground displacements with centimetre accuracy [1]. In the last decade, advanced DInSAR algorithms, such as the Small Baseline Subset (SBAS) [2] one that is aimed at following the temporal evolution of the ground deformation, showed to be significantly useful remote sensing tools for the geoscience communities as well as for those related to hazard monitoring and risk mitigation. DInSAR scenario is currently characterized by the large and steady increasing availability of huge SAR data archives that have a broad range of diversified features according to the characteristics of the employed sensor. Indeed, besides the old generation sensors, that include ERS, ENVISAT and RADARSAT systems, the new X-band generation constellations, such as COSMO-SkyMed and TerraSAR-X, have permitted an overall study of ground deformations with an unprecedented detail thanks to their improved spatial resolution and reduced revisit time. Furthermore, the incoming ESA Sentinel-1 SAR satellite is characterized by a global coverage acquisition strategy and 12-day revisit time and, therefore, will further contribute to improve deformation analyses and monitoring capabilities. However, in this context, the capability to process such huge SAR data archives is strongly limited by the existing DInSAR algorithms, which are not specifically designed to exploit modern high performance computational infrastructures (e.g. cluster, grid and cloud computing platforms). The goal of this paper is to present a Parallel version of the SBAS algorithm (P-SBAS) which is based on a dual-level parallelization approach and embraces combined parallel strategies [3], [4]. A detailed description of the P-SBAS algorithm will be provided together with a scalability analysis focused on studying its performances. In particular, a P-SBAS scalability analysis with respect to the number of exploited CPUs has

  5. Pañoletas y polainas. Dinámicas de la moda en la Cuba soviética

    OpenAIRE

    Cabrera Arús, Maria Antonia

    2015-01-01

    Resumen: El texto explora el rol de las dinámicas de la moda en la consolidación del socialismo de estado de tipo soviético en Cuba. Se afirma que la moda participó de dinámicas de dominación, legitimación y control en los años 1960s y 1970s. Se sostiene que el régimen cubano promovió significados denotativos de la cultura material que conectaron de manera directa valores políticos y estilos de la moda, y se ofrecen ejemplos que acercan el estudio de este país a los estudios contemporáneos de...

  6. On the inhibition of mild steel corrosion by 4-amino-5-phenyl-4H-1, 2, 4-trizole-3-thiol

    International Nuclear Information System (INIS)

    Musa, Ahmed Y.; Kadhum, Abdul Amir H.; Mohamad, Abu Bakar; Takriff, Mohd Sobri; Daud, Abdul Razak; Kamarudin, Siti Kartom

    2010-01-01

    The corrosion inhibition of mild steel in a 2.5 M H 2 SO 4 solution by 4-amino-5-phenyl-4H-1, 2, 4-trizole-3-thiol (APTT) was studied at different temperatures, utilising open circuit potential, potentiodynamic and impedance measurements. The results indicate that APTT performed as an excellent mixed-type inhibitor for mild steel corrosion in a 2.5 M H 2 SO 4 solution and that the inhibition efficiencies increased with the inhibitor concentration but decreased proportionally with temperature. The kinetic and thermodynamic parameters for adsorption of APTT on the mild steel surface were calculated. A chemisorption mechanism of APTT molecules on the mild steel surface was proposed based on the thermodynamic adsorption parameters.

  7. O enfermeiro como coordenador de grupos: contribuições da Dinâmica de Grupo

    Directory of Open Access Journals (Sweden)

    Carla Natalina da Silva Fernandes

    2008-03-01

    Full Text Available Na enfermagem a utilização do recurso grupal tem sido utilizada para trabalhar com pessoas o que exige dos profissionais um conhecimento específico, para atender aos objetivos do grupo sem causar danos aos envolvidos. O objetivo desta pesquisa foi discutir à luz do referencial teórico da Dinâmica de Grupo os atributos desejáveis para o enfermeiro como coordenador de grupos, suas possibilidades e limitações. Trata-se de uma investigação teórica, de natureza descritiva e analítica desenvolvida por meio de pesquisa bibliográfica. Consideramos como fontes bibliográficas, inicialmente, os livros clássicos de Lewin (1948, Mailhiot (1981 e Cartwright e Zander (1975 por serem as primeiras referências na construção da ciência da dinâmica de grupo e, ainda, para a discussão teórica, a contribuição de outros autores da literatura contemporânea nacional e internacional, de acordo com sua adequação ao objetivo proposto nesse trabalho. A análise das obras foi direcionada pelo interesse na busca de elementos para o alcance do objetivo proposto. Estruturamos os resultados do trabalho em três capítulos. O primeiro capítulo Dinâmica e Funcionamento de Grupo: perspectiva histórica, conceito e fundamentos, traz conceitos fundamentais sobre a origem da dinâmica de grupo e os pressupostos iniciais. Discutimos as diferentes e complementares concepções de grupo, sendo que a fundamentação teórica e filosófica do coordenador norteará o caminho da satisfação dos objetivos propostos pelo grupo. No segundo capítulo Coordenação de Grupos: fundamentos da Ciência da Dinâmica de Grupo, abordamos os aspectos da coordenação de grupo, incluindo o planejamento e várias fases que o grupo percorre no seu desenvolvimento. Discutimos ainda os fundamentos para a sistematização da atividade grupal. No último capítulo: O enfermeiro como coordenador de grupos: discutindo caminhos para a atuação na assistência, formação de

  8. Ferritic steels for French LMFBR steam generators

    International Nuclear Information System (INIS)

    Aubert, M.; Mathieu, B.; Petrequin, P.

    1983-06-01

    Austenitic stainless steels have been widely used in many components of the French LMFBR. Up to now, ferritic steels have not been considered for these components, mainly due to their relatively low creep properties. Some ferritic steels are usable when the maximum temperatures in service do not exceed about 530 0 C. It is the case of the steam generators of the Phenix plant, where the exchange tubes of the evaporator are made of 2,25% Cr-1% Mo steel, stabilized or not by addition of niobium. These ferritic alloys have worked successfully since the first steam production in October 1973. For the SuperPhenix power plant, an ''all austenitic stainless alloy'' apparatus has been chosen. However, for the future, ferritic alloys offer potential for use as alternative materials in the evaporators: low alloys steels type 2,25% Cr-1% Mo (exchange tubes, tube-sheets, shells), or at higher chromium content type 9% Cr-2% Mo NbV (exchange tubes) or 12M Cr-1% Mo-V (tube-sheets). Most of these steels have already an industrial background, and are widely used in similar applications. The various potential applications of these steels are reviewed with regards to the French LMFBR steam generators, indicating that some points need an effort of clarification, for instance the properties of the heterogeneous ferritic/austenitic weldments

  9. Response of ferritic steels to nonsteady loading at elevated temperatures

    International Nuclear Information System (INIS)

    Swindeman, R.W.

    1984-01-01

    High-temperature operating experience is lacking in pressure vessel materials that have strength levels above 586 MPa. Because of their tendency toward strain softening, we have been concerned about their behavior under nonsteady loading. Testing was undertaken to explore the extent of softening produced by monotonic and cyclic strains. The specific materials included bainitic 2 1/4Cr-1Mo steel, a micro-alloyed version of 2 1/4Cr-1Mo steel, a micro-alloyed version of 2 1/4Cr-1Mo steel containing vanadium, titanium, and boron, and a martensitic 9Cr-1Mo-V-Nb steel. Tests included tensile, creep, variable stress creep, relaxation, strain cycling, stress cycling, and non-isothermal creep ratchetting experiments. We found that these steels had very low uniform elongation and exhibited small strains to the onset of tertiary creep compared to annealed 2 1/4Cr-1Mo steel. Repeated relaxation test data also indicated a limited capacity for strain hardening. Reversal strains produced softening. The degree of softening increased with increased initial strength level. We concluded that the high strength bainitic and martensitic steels should perform well when used under conditions where severe cyclic operation does not occur

  10. Fundamentos e métodos de medidas de energia dinâmica no SPT

    Directory of Open Access Journals (Sweden)

    Antonio Belincanta

    2000-05-01

    Full Text Available Discutem-se neste trabalho os métodos disponíveis no Brasil e no exterior para a medida da energia transferida às hastes no SPT, apresentando-se inclusive registros típicos dos eventos dinâmicos correspondentes

  11. Thin-sheet zinc-coated and carbon steels laser welding

    Directory of Open Access Journals (Sweden)

    Peças, P.

    1998-04-01

    Full Text Available This paper describes the results of a research on CO2 laser welding of thin-sheet carbon steels (zinccoated and uncoated, at several thicknesses combinations. Laser welding has an high potential to be applied on sub-assemblies welding before forming to the automotive industry-tailored blanks. The welding process is studied through the analysis of parameters optimization, metallurgical quality and induced distortions by the welding process. The clamping system and the gas protection system developed are fully described. These systems allow the minimization of common thin-sheet laser welding defects like misalignement, and zinc-coated laser welding defects like porous and zinc volatilization. The laser welding quality is accessed by DIN 8563 standard, and by tensile, microhardness and corrosion tests.

    Este artigo descreve os resultados da investigação da soldadura laser de CO2 de chapa fina de acó carbono (simples e galvanizado, em diferentes combinações de espessura. A soldadura laser é um processo de elevado potencial no fabrico de tailored-blanks (sub-conjuntos para posterior enformação, constituidos por varias partes de diferentes materiais e espessuras para a indústria automóvel. São analisados os aspectos de optimização paramétrica, de qualidade metalúrgica da junta soldada e das deformações resultantes da soldadura. São descritos os mecanismos desenvolvidos de fixação das chapas e protecção gasosa, por forma a minimizar os defeitos típicos na soldadura laser de chapa fina como o desalinhamento e da soldadura laser de chapa galvanizada como os poros e a volatilização do zinco. Por fim apresentam-se resultados da avaliação da qualidade da soldadura do ponto de vista qualitativo através da norma DIN 8563, e do pontos de vista quantitativo através de ensaios de tracção, dureza e corrosão.

  12. Phase Transformations of an Fe-0.85 C-17.9 Mn-7.1 Al Austenitic Steel After Quenching and Annealing

    Science.gov (United States)

    Cheng, Wei-Chun

    2014-09-01

    Low-density Mn-Al steels could potentially be substitutes for commercial Ni-Cr stainless steels. However, the development of the Mn-Al stainless steels requires knowledge of the phase transformations that occur during the steel making processes. Phase transformations of an Fe-0.85 C-17.9 Mn-7.1 Al (wt.%) austenitic steel, which include spinodal decomposition, precipitation transformations, and cellular transformations, have been studied after quenching and annealing. The results show that spinodal decomposition occurs prior to the precipitation transformation in the steel after quenching and annealing at temperatures below 1023 K and that coherent fine particles of L12-type carbide precipitate homogeneously in the austenite. The cellular transformation occurs during the transformation of high-temperature austenite into lamellae of austenite, ferrite, and kappa carbide at temperatures below 1048 K. During annealing at temperatures below 923 K, the austenite decomposes into lamellar austenite, ferrite, κ-carbide, and M23C6 carbide grains for another cellular transformation. Last, when annealing at temperatures below 873 K, lamellae of ferrite and κ-carbide appear in the austenite.

  13. Apparatus of irradiation of steel test pieces in the Marcoule pile G 1

    International Nuclear Information System (INIS)

    Marinot, R.; Wallet, Ph.

    1960-01-01

    Test pieces of steel were irradiated in the reactor G1 at Marcoule, in convectors replacing fuel elements, and in vertical channels in furnace-heated containers. The apparatus designed for this irradiation is described: containers, converter-rods, suspension fixtures and clamps, temperature measurement devices, lead castles and unloading set-ups. (author) [fr

  14. Monitoring of surface deformation in open pit mine using DInSAR time-series: a case study in the N5W iron mine (Carajás, Brazil) using TerraSAR-X data

    Science.gov (United States)

    Mura, José C.; Paradella, Waldir R.; Gama, Fabio F.; Santos, Athos R.; Galo, Mauricio; Camargo, Paulo O.; Silva, Arnaldo Q.; Silva, Guilherme G.

    2014-10-01

    We present an investigation of surface deformation using Differential SAR Interferometry (DInSAR) time-series carried out in an active open pit iron mine, the N5W, located in the Carajás Mineral Province (Brazilian Amazon region), using 33 TerraSAR-X (TSX-1) scenes. This mine has presented a historical of instability and surface monitoring measurements over sectors of the mine (pit walls) have been done based on ground based radar. Two complementary approaches were used: the standard DInSAR configuration, as an early warning of the slope instability conditions, and the DInSAR timeseries analysis. In order to decrease the topographic phase error a high resolution DEM was generated based on a stereo GeoEye-1 pair. Despite the fact that a DinSAR contains atmospheric and topographic phase artifacts and noise, it was possible to detect deformation in some interferometric pairs, covering pit benches, road ramps and waste piles. The timeseries analysis was performed using the 31 interferometric pairs, which were selected based on the highest mean coherence of a stack of 107 interferograms, presenting less phase unwrapping errors. The time-series deformation was retrieved by the Least-Squares (LS) solution using an extension of the Singular Value Decomposition (SVD), with a set of additional weighted constrain on the acceleration deformation. The atmospheric phase artifacts were filtered in the space-time domain and the DEM height errors were estimated based on the normal baseline diversity. The DInSAR time-series investigation showed good results for monitoring surface displacement in the N5W mine located in a tropical rainforest environment, providing very useful information about the ground movement for alarm, planning and risk assessment.

  15. TiC reinforced cast Cr steels

    Energy Technology Data Exchange (ETDEWEB)

    Dogan, O.N.; Hawk, J.A.; Schrems, K.K.

    2006-06-01

    A new class of materials, namely TiC-reinforced cast chromium (Cr) steels, was developed for applications requiring high abrasion resistance and good fracture toughness. The research approach was to modify the carbide structure of commercial AISI 440C steel for better fracture resistance while maintaining the already high abrasion resistance. The new alloys contained 12Cr, 2.5–4.5Ti, and 11.5C (wt.%) and were melted in a vacuum induction furnace. Their microstructure was composed primarily of a martensitic matrix with a dispersion of TiC precipitates. Modification of TiC morphology was accomplished through changing the cooling rate during solidification. Wear rates of the TiC-reinforced Cr steels were comparable to that of AISI 440C steel, but the impact resistance was much improved.

  16. TiC-reinforced cast Cr steels

    Science.gov (United States)

    Doğan, Ö. N.; Hawk, J. A.; Schrems, K. K.

    2006-06-01

    A new class of materials, namely TiC-reinforced cast chromium (Cr) steels, was developed for applications requiring high abrasion resistance and good fracture toughness. The research approach was to modify the carbide structure of commercial AISI 440C steel for better fracture resistance while maintaining the already high abrasion resistance. The new alloys contained 12Cr, 2.5-4.5Ti, and 1-1.5C (wt.%) and were melted in a vacuum induction furnace. Their microstructure was composed primarily of a martensitic matrix with a dispersion of TiC precipitates. Modification of TiC morphology was accomplished through changing the cooling rate during solidification. Wear rates of the TiC-reinforced Cr steels were comparable to that of AISI 440C steel, but the impact resistance was much improved.

  17. The Effects of Substitution of The Natural Sand by Steel Slag in The Properties of Eco-Friendly Concrete with The 1:2:3 Ratio Mixing Method

    Science.gov (United States)

    Rahmawati, A.; Saputro, I. N.

    2018-03-01

    This study was motivated by the need for the development of eco-friendly concrete, and the use of large quantities of steel slag as an industrial waste which is generated from the steel manufacturers. This eco-friendly concrete was developed with steel slag as a substitute for natural sand. Properties of concrete which used waste slag as the fine aggregate with the 1 cement: 2 sand : 3 coarse aggregate ratio mixing method were examined. That ratio was in volume. Then a part of natural sand replaced with steel slag sand in six variations percentages that were 0 %, 20 %, 40 %, 60 %, 80 % and 100 %. The compressive strength, tensile strength, and flexural strength of concrete specimens were determined after curing for 28 days. The research results demonstrate that waste steel slag can increase the performance of concrete. The optimal percentage substitution natural sand by steel slag sand reached of slag on the percentage of 20 % which reached strength ratios of steel slag concrete to the strength of conventional concrete with natural sandstone were 1.37 for compressive strength and 1.13 for flexural strength. While the tensile strength reached a higher ratio of concrete with steel slag sand to the concrete with natural sand on the 80% substitution of natural sand with steel slag sand.

  18. Dinámica demográfica y generación de viajes al trabajo en el AMCM: 1994-2000

    Directory of Open Access Journals (Sweden)

    Boris Graizbord

    2005-01-01

    Full Text Available Entre la vasta gama de problemas urbanos que afectan a la Ciudad de México es de vital importancia el transporte pues implica la movilidad de la población. Los diversos modos de transporte, públicos y privados, permiten acceder a los mercados urbanos, principalmente al de trabajo y al de vivienda, pero también a los mercados de bienes y servicios. Sin embargo, no se ha llevado a cabo un análisis a fondo de tales fenómenos conforme lo exigen los problemas, y a nuestro entender esto obedece a dos razones fundamentales: 1 la incipiente generación y escasa disponibilidad de datos que permitananalizar la estructura del transporte, y 2 la carencia de los elementos conceptuales necesarios para vincular el transporte con la dinámica de crecimiento de la metrópoli ycon el proceso de planificación de la ciudad. En este trabajo pretendemos avanzar en el análisis de la dinámica del transporte urbano de pasajeros en el Área Metropolitana de la Ciudad de México (AMCM. Lo haremos resaltando las diferencias absolutas y relativas en la generación de viajes rumbo al trabajo en dos momentos en el tiempo: 1994 y 2000. Esto nos brinda la posibilidad de acercarnos a una mayor comprensión de la dinámica de dos fenómenos,la ciudad y el transporte, y de apreciar así algunas relaciones entre ambos.

  19. Synergistic effect of iodide ion addition on the inhibition of mild steel corrosion in 1 M HCl by 3-amino-2-methylbenzylalcohol

    Energy Technology Data Exchange (ETDEWEB)

    Obot, I.B., E-mail: obot@kfupm.edu.sa; Madhankumar, A.

    2016-07-01

    The inhibition of mild steel corrosion in 1 M HCl aqueous solution by 3-amino-2-methylbenzylalcohol (AMBA) was investigated using weight loss, electrochemical impedance spectroscopy (EIS), potentiodynamic polarization (PDP) and cyclic voltammametry (CV) techniques. Attenuated total reflectance infrared spectroscopy (ATR-IR), contact angle (CA) and scanning electron microscopy (SEM) measurements were carried out to confirm the adsorption of AMBA on mild steel surface. Computer simulations using density functional theory (DFT) and Monte Carlo methodologies were further employed to provide insights into the mechanism of interaction between the inhibitor and the steel surface. All the results confirmed that AMBA is a good corrosion inhibitor for mild steel in 1 M HCl. The addition of NaI was found to increase the inhibition effect of AMBA on mild steel to a considerable extent. DFT results reveal that the N atom together with the π-systems in the aromatic ring were the active sites for the interaction of AMBA with steel surface. Furthermore, the negative value of the adsorption energy obtained from the Monte Carlo simulation indicates the stability of the adsorbed inhibitor film on the steel surface. - Graphical abstract: EIS spectra and adsorption configuration of AMBA on Fe (110). - Highlights: • 3-amino-2-methylbenzylalcohol inhibit mild steel corrosion in acid medium. • ATR-IR, contact angle, SEM, were used for steel surface characterization. • DFT and Monte Carlo simulations provide atomic and molecular level insights. • The theoretical data clearly support the experimental results obtained.

  20. Research and tests of steel-concrete-steel sandwich composite shear wall in reactor containment of HTR-PM

    International Nuclear Information System (INIS)

    Sun Yunlun; Huang Wen; Zhang Ran; Zhang Pei; Tian Chunyu

    2014-01-01

    By quasi-static test of 8 specimens of steel-concrete-steel sandwich composite shear wall, the bearing capacity, hysteretic behavior, failure mode of the specimens was studied. So was the effect of the shear-span ratios, steel ratios and spacing of studs on the properties of the specimens. The failure patterns of all specimens with different shear-span ratios between 1.0 and 1.5 were compression-bending failure. The hysteretic curves of all specimens were relatively plump, which validated the well deformability and energy dissipation capacity of the specimens. When shear-span ratio less than 1.5, the shear property of the steel plate was well played, and so was the deformability of the specimens. The bigger the steel ratio was, the better the lateral resistance capacity and the deformability was. Among the spacing of studs in the test, the spacing of studs had no significant effect on the bearing capacity, deformability and ductility of the specimens. Based on the principle of superposition an advised formula for the compression-bending capacity of the shear wall was proposed, which fitted well with the test result and had a proper safety margin. (author)

  1. Mechanical properties of irradiated 9Cr-2WVTa steel

    International Nuclear Information System (INIS)

    Klueh, R.L.; Alexander, D.J.; Rieth, M.

    1998-01-01

    An Fe-9Cr-2W-0.25V-0.07Ta-0.1C (9Cr-2WVTa) steel has excellent strength and impact toughness before and after irradiation in the Fast Flux Test Facility and the High Flux Reactor (HFR). The ductile-brittle transition temperature (DBTT) increased only 32 C after 28 dpa at 365 C in FFTF, compared to a shift of ∼60 C for a 9Cr-2WV steel--the same as the 9Cr-2WVTa steel but without tantalum. This difference occurred despite the two steels having similar tensile but without tantalum. This difference occurred despite the two steels having similar tensile properties before and after irradiation. The 9Cr-2WVTa steel has a smaller prior-austenite grain size, but otherwise microstructures are similar before irradiation and show similar changes during irradiation. The irradiation behavior of the 9Cr-2WVTa steel differs from the 9Cr-2WV steel and other similar steels in two ways: (1) the shift in DBTT of the 9Cr-2WVTa steel irradiated in FFTF does not saturate with fluence by ∼28 dpa, whereas for the 9Cr-2WV steel and most similar steels, saturation occurs at <10 dpa, and (2) the shift in DBTT for 9Cr-2WVTa steel irradiated in FFTF and HFR increased with irradiation temperature, whereas it decreased for the 9Cr-2WV steel, as it does for most similar steels. The improved properties of the 9Cr-2WVTa steel and the differences with other steels were attributed to tantalum in solution

  2. The behaviour of concrete under attack of liquid steel

    International Nuclear Information System (INIS)

    Schneider, U.; Ehm, C.; Diederichs, U.

    1983-01-01

    Investigations were carried out to study the interaction between concrete and liquid steel. Different types and different forms of concrete were investigated at temperatures of liquid steel between 1.600 and 2.600 0 C. The liquid steel of 1.600 0 C was produced in an induction furnace, the liquid steel of 2.600 0 C was produced in concrete crucibles by metallothermic reactions. The reactions occuring during the interaction of concrete and liquid steel may be summarized as follows: - Concrete reacts violently upon sudden loading with high temperatures and high heat fluxes. Great quantities of steam and gases are generated. The mechanical strength decreases rapidly with increasing temperature. -At about 1.200 0 C concrete begins to melt. First the cement matrix melts, than the aggregates melt. The melts of different concretes consist of different constituents and their reactions with liquid steel vary. The temperature of the liquid steel significantly influences the intensity of the reactions and the erosion rates. - The erosion rates amounted to 30 mm/min, when liquid steel was produced in concrete crucibles. When cylindrical concrete specimens were immersed in molten steel the rate of melting off amounted up to 66 mm/min. - The dissipation of heat during the interaction brings about that the reactions between concrete and liquid steel vanish gradually, if no additional energy is fed into the system. (orig.)

  3. Gestión dinámica de conocimiento organizacional

    Directory of Open Access Journals (Sweden)

    José Francisco Mirabal

    2015-08-01

    Full Text Available La presente investigación propone elementos que guían la conformación de organizaciones dinámicas en conocimiento de comportamiento inteligente, a partir del desarrollo de capacidades y estructuras distintivas articuladas que agregan valor diferenciador en la organización. Para ello, se efectuó un estudio no experimental donde se aplicó un modelo mixto complejo, que consistió en una revisión documental para identificar elementos del marco estratégico-táctico de sustentación, un intercambio con expertos con los fines de determinar aspectos mediadores, socializadores de sustento cognitivo y la elaboración de un estudio proyectivo para proponer soluciones que permitan una forma ágil de construir conocimiento para la acción. En el análisis se observó, que la gestión de conocimiento está condicionada mayormente por dominios cognitivos aislados, es poco socializada, no está generalmente interrelacionada con hechos significativos internos o externos y habitualmente, la información requerida, está desagregada en sistemas aislados. Asimismo, se prevé que para asimilar la alta variabilidad del entorno dar agilidad operacional, así como también facilitar la organización interna, es imprescindible articular objetos de conocimiento mediante estructuras integradas sistémicamente para que exista interconexión ágil desde la perspectiva individual, grupal y organizacional, tanto interna como externa para inducir de manera inteligente conocimiento que en forma dinámica genere acciones acertadas en tiempo real

  4. Study of the 1.25Cr-1Mo-0.25V steel microstructure after a carburization phenomenon

    Energy Technology Data Exchange (ETDEWEB)

    Simonetti, S., E-mail: ssimonet@uns.edu.ar [Departamento de Fisica, Universidad Nacional del Sur, Av. Alem 1253, 8000 Bahia Blanca (Argentina); Departamentos de Ciencias Basicas e Ingenieria Mecanica, Universidad Tecnologica Nacional, 11 de Abril 461, 8000 Bahia Blanca (Argentina); Lanz, C. [Departamento de Ingenieria, Universidad Nacional del Sur, Av. Alem 1253, 8000 Bahia Blanca (Argentina); Brizuela, G.; Juan, A. [Departamento de Fisica, Universidad Nacional del Sur, Av. Alem 1253, 8000 Bahia Blanca (Argentina)

    2010-08-20

    We studied the changes in the structure and carbide particle size in 1.25Cr-1Mo-0.25V steel under 600 deg. C and 168 MPa, after 4000 h service. We used microscopy and microanalysis techniques to analyze the carbide particles. We performed a complementary theoretical study on the chemical bonding and electronic structure of the carbide-Fe matrix interaction. The results contribute to the understanding of the changes in the alloy microstructure caused by the carburization phenomenon.

  5. Some aspects of thermal fatigue in stainless steel

    International Nuclear Information System (INIS)

    Iorio, A.F.; Crespi, J.C.

    1987-01-01

    This paper is concerned with the analysis of failures in a moderator circuit branch piping of the ATUCHA-I pressurized heavy water reactor (PHWR), made of austenitic steel to DIN 1.4550 specification (similar to AISI 347). These failures are considered to result from a thermal fatigue processes induced by fluctuations in a zone where stratified temperature layers occurred -the fluctuations being associated with variations in the heavy water flow. The first section evaluates the possibility of cracking due to thermal fatigue phenomena and concludes that under service conditions a crack may be initiated and growth through 7 mm of the wall thickness of the pipe. Laboratory thermal fatigue tests that simulated the thermomechanical conditions for such a component, showed that the number of cycles required to initiate a thermal fatigue crack in a notched modified standard fatigue specimen was about 10 3 . This value may be used to give a conservative prediction of the number of thermal cycles for crack initiation in actual station piping, including those who suffered a cold plug condition which is produced in some emergency shut-down and valve testing situations. It was also demonstrated that beyond a crack depth of 7 mm stress corrosion cracking has the main process in further crack propagation. The relevance of this prediction has been confirmed by microfractographic observations, since the brittle nature of the fracture surfaces under service conditions appears very different from the transgranular ductile striations found in both thermal and mechanical fatigue test specimens as a result of environmental effects. (Author)

  6. Las dinámicas interactivas en el ámbito universitario: el clima de aula

    Directory of Open Access Journals (Sweden)

    Zulay Pereira-Pérez

    2010-10-01

    Full Text Available Recibido 28 de julio de 2009 • Aceptado 02 de diciembre de 2009 • Corregido 20 de marzo de 2010     Las relaciones interpersonales en el ámbito humano cobran vital sentido desde el nacimiento y se van conformando en los procesos de interacción y socialización. El contexto educativo no está exento de procesos comunicativos e interactivos. Es en el aula de clase, donde, de manera más específica, se pueden identificar dichos procesos. El aula puede ser entendida como el espacio físico-humano, en el cual se desarrollan dinámicas a partir de las interacciones entre el profesorado y el grupo estudiantil, los contenidos, las estrategias de aprendizaje y el clima de aula que de ello se genera; aspectos todos, que como parte de los procesos de enseñanza y de aprendizaje están presentes en el ámbito de la clase. Es interesante analizar el clima de aula y las dinámicas interactivas que en ella se desarrollan, independientemente de la edad del estudiante –ya sea que se trate de infantes, adolescentes o adultos–. En este caso particular, se analiza el clima de aula en el ámbito universitario, entendiendo que las dinámicas interactivas que en el aula se desarrollen, determinan un ambiente propicio o no, para el proceso de enseñanza y de aprendizaje, que ha de ser considerado, si se opta por una educación integral y de calidad.

  7. Steel for nuclear applications

    International Nuclear Information System (INIS)

    Zorev, N.N.; Astafiev, A.A.; Loboda, A.S.

    1978-01-01

    A steel contains, in percent by weight, the following constituents: carbon from 0.13 to 0.18, silicon from 0.17 to 0.37, manganese from 0.30 to 0.60, chromium from 1.7 to 2.4, nickel from 1.0 to 1.5, molybdenum from 0.5 to 0.7, vanadium from 0.05 to 0.12, aluminium from 0.01 to 0.035, nitrogen from 0.05 to 0.012, copper from 0.11 to 0.20, arsenic from 0.0035 to 0.0055, iron and impurities, the balance. This steel is preferable for use in the manufacture of nuclear reactors. 1 table

  8. Hydrogen permeation rate reduction by post-oxidation of aluminide coatings on DIN 1.4914 martensitic steel (MANET)

    International Nuclear Information System (INIS)

    Perujo, A.; Sample, T.

    1996-01-01

    In a previous work, it has been shown that lower aluminium content aluminide, having the same permeation rate reduction as the higher aluminium content, exhibited a lower hardness and greater ductility and therefore greater crack resistance than the higher aluminium content. In this work we combine this characteristic with a post-oxidation to obtain a further deuterium permeation reduction. The post-oxidation was performed in air at 1023 K for 15 h and at 1223 K for 10 h and 1 h. The maximum deuterium permeation rate reduction obtained is very moderate (maximum of a factor 500 for 1 h at 1223 K) as compared to that of the non-oxidised aluminide specimen (two orders of magnitude) and is constant in the temperature range studied (573-800 K). This method has the technological appeal of using air rather than the controlled environment used by other authors. (orig.)

  9. Variations in frequency content of acoustic emission during extension of HF-1 steel

    International Nuclear Information System (INIS)

    Hartman, W.F.; Kline, R.A.

    1977-01-01

    Acoustic emissions resulting from continuous, dead-weight, tensile loading of quenched and tempered HF-1 steel were analyzed for frequency content. Three distinct frequency spectra were observed. These correspond to microplasticity, plasticity and deformation after recovery. It is shown that frequency analysis of acoustic emission can be a sensitive evaluation technique for assessing structural integrity

  10. Connection and Community: Diné College Emphasizes Real-World Experience in Public Health

    Science.gov (United States)

    Bauer, Mark

    2016-01-01

    The Summer Research Enhancement Program (SREP) at Diné College provides students with a solid foundation of public health research methods and includes a hands-on internship in their home community to test their newly acquired skills while enhancing the communities' health. Focusing on health issues prioritized by Navajo health leaders, from…

  11. Role of RecA protein in untargeted UV mutagenesis of bacteriophage lambda: evidence for the requirement for the dinB gene

    International Nuclear Information System (INIS)

    Brotcorne-Lannoye, A.; Maenhaut-Michel, G.

    1986-01-01

    Untargeted UV mutagenesis of bacteriophage lambda--i.e., the increased recovery of lambda mutants when unirradiated lambda infects UV-irradiated Escherichia coli--is thought to be mediated by a transient decrease in DNA replication fidelity, generating mutations in the newly synthesized strands. Using the bacteriophage lambda cI857----lambda c mutation system, we provide evidence that the RecA protein, shown previously to be required for this mutagenic pathway, is no longer needed when the LexA protein is inactivated by mutation. We suggest that the error-prone DNA replication responsible for UV-induced untargeted mutagenesis is turned on by the presence of replication-blocking lesions in the host cell DNA and that the RecA protein is required only to derepress the relevant din gene(s). This is in contrast to mutagenesis of irradiated bacteria or irradiated phage lambda, in which activated RecA protein has a second role in mutagenesis in addition to the cleavage of the LexA protein. Among the tested din genes, the dinB gene product (in addition to the uvrA and uvrB gene products) was found to be required for untargeted mutagenesis of bacteriophage lambda. To our knowledge, a phenotype associated with the dinB gene has not been reported previously

  12. Dynamic characteristics of automotive steel sheets

    Directory of Open Access Journals (Sweden)

    M. Mihaliková

    2016-10-01

    Full Text Available The aim of this experimental research was to perform an analysis of deformation characteristics on two different types of steel: IF steel, and micro-alloyed steel were used automotive industry. For that purpose changes of properties of these materials were carried out by static 10-3 · s-1 and dynamic 103 · s-1 strain rate assess its plastic properties. Vickers micro hardness test was carried out by the static and dynamic loading condition and describes different hardness distribution. The higher strain hardening of materials was obtained too that was confirmed by distribution of dislocations.

  13. Hydrogen transport in iron and steel

    International Nuclear Information System (INIS)

    Louthan, M.R. Jr.; Derrick, R.G.; Donovan, J.A.; Caskey, G.R. Jr.

    1975-01-01

    The permeabilities of protium, deuterium, and tritium in iron and T-1 steel at temperatures as low as 260 0 K are in agreement with the equation proposed by Gonzalez. However, the permeabilities of HP-9-4-20 and 4130 steel to hydrogen are typically lower than predicted. The present data also show that, within experimental accuracy, the isotope effect on the permeability of hydrogen in HP-9-4-20, 4130 and T-1 steel, and high purity iron can be estimated by an inverse square root of mass correction. Trapping effects prevent the development of diffusivity and solubility equations. (auth)

  14. Void formation and helium effects in 9Cr-1MoVNb and 12Cr-1MoVW steels irradiated in HFIR and FFTF at 400/degree/C

    International Nuclear Information System (INIS)

    Maziasz, P.J.; Klueh, R.L.

    1988-01-01

    Martensitic/ferritic 9Cr-1MoVNb and 12Cr-1MoVW steels doped with up to 2 wt% Ni have up to 450 appm He after HFIR irradiation to /approximately/38 dpa, but only 5 appm He after 47 dpa in FFTF. No fine He bubbles and few or no larger voids were observable in any of these steels after FFTF irradiation at 407/degree/C. By contrast, many voids were found in the undoped steels (30-90 appm He) irradiated in HFIR at 400/degree/C, while voids plus many more fine He bubbles were found in the Ni-doped steels (400-450 appm He). Irradiation in both reactors at /approximately/400/degree/C produced significant changes in the as-tempered lath/subgrain boundary, dislocation, and precipitation structures that were sensitive to alloy composition, including doping with Ni. However, for each specific alloy the irradiation-produced changes were exactly the same comparing samples irradiated in FFTF and HFIR, particularly the Ni-doped steels. Therefore, the increased void formation appears solely due to the increased helium generation found in HFIR. While the levels of void swelling are relatively low after 37-39 dpa in HFIR (0.1-0.4%), details of the microstructural evolution suggest that void nucleation is still progressing, and swelling could increase with dose. The effect of helium on void swelling remains a valid concern for fusion application that requires higher dose experiments. 15 refs., 14 figs., 8 tabs

  15. Dinâmicas sociais e estados de humor Social dynamics and mood states

    Directory of Open Access Journals (Sweden)

    Flávio Rebustini

    2012-06-01

    Full Text Available O objetivo do estudo foi avaliar as relações das dinâmicas sociais (família, amigos e escola; i.e., três fatores sociais sobre os estados de humor. A pesquisa foi realizada com uma equipe feminina de voleibol (14/15 anos. Aplicou-se o teste POMS (Profile of Mood States para mensurar os estados de humor. Foi utilizada uma escala de 1 (muito mal a 5 (muito bem para que as atletas avaliassem cada um dos três fatores. Os resultados apontaram correlações significativas entre as escalas e os estados de humor; e diferenças significativas entre os níveis de intensidade apontados na escala dos três fatores e os estados de humor. Os resultados indicam clara interferência das dinâmicas sociais sobre os estados de humor, portanto, as interferências sociais não podem ser descartadas na preparação do atleta.The aim of this study was to evaluate the impact of social dynamics (family, friends and school; i.e., three social factors on mood states. The survey was conducted with a women's volleyball team (14/15 years. The POMS test (Profile of Mood States was employed to measure the team's mood states. The athletes assessed the three factors by the use of a Likert scale ranging from 1 (very bad to 5 (very good. Results showed significant correlations between scales and mood states, and significant differences between the intensity levels representing their moods for each of the three factors. The results show clear interference of social dynamics on the mood states. Therefore, social interference cannot be ignored during an athlete's training program.

  16. The Study on Weldability of Boron Steel and Hot-Stamped Steel by Using Laser Heat Source (Ⅲ) - Comparison on Laser Weldability of Boron Steel and Hot -Stamped Steel-

    Energy Technology Data Exchange (ETDEWEB)

    Choi, So Young; Kim, Jong Do [Korea Maritime and Ocean University, Busan (Korea, Republic of); Kim, Jong Su [Korea Institute of Machinery and Materials, Daejeon (Korea, Republic of)

    2015-01-15

    This study was conducted to compare the laser weldability of boron steel and hot-stamped steel. In general, boron steel is used in the hot-stamping process. Hot-stamping is a method for simultaneously forming and cooling boron steel in a press die after heating it to the austenitizing temperature. Hot-stamped steel has a strength of 1500 MPa or more. Thus, in this study, the laser weldability of boron steel and that of hot-stamped steel were investigated and compared. A continuous wave disk laser was used to produce butt and lap joints. In the butt welding, the critical cooling speed at which full penetration was obtained in the hot-stamped steel was lower than that of boron steel. In the lap welding, the joint widths were similar regardless of the welding speed when full penetration was obtained.

  17. The Study on Weldability of Boron Steel and Hot-Stamped Steel by Using Laser Heat Source (Ⅲ) - Comparison on Laser Weldability of Boron Steel and Hot -Stamped Steel-

    International Nuclear Information System (INIS)

    Choi, So Young; Kim, Jong Do; Kim, Jong Su

    2015-01-01

    This study was conducted to compare the laser weldability of boron steel and hot-stamped steel. In general, boron steel is used in the hot-stamping process. Hot-stamping is a method for simultaneously forming and cooling boron steel in a press die after heating it to the austenitizing temperature. Hot-stamped steel has a strength of 1500 MPa or more. Thus, in this study, the laser weldability of boron steel and that of hot-stamped steel were investigated and compared. A continuous wave disk laser was used to produce butt and lap joints. In the butt welding, the critical cooling speed at which full penetration was obtained in the hot-stamped steel was lower than that of boron steel. In the lap welding, the joint widths were similar regardless of the welding speed when full penetration was obtained

  18. Estimación de modelos econométricos dinámicos lineales en tiempo continuo con observaciones discretas y medidas con error

    OpenAIRE

    Nuño Sevilla, Luis Enrique

    2004-01-01

    El problema considerado en esta tesis es la estimación de los parámetros de modelos econométricos dinámicos lineales gaussianos formulados en tiempo continuo cuando las observaciones son discretas y se recogen a intervalos irregulares de tiempo. Además, se permite la posibilidad de que las observaciones difieran de las variables cuya dinámica se representa en el modelo.

  19. Quantification by image analysis of grain size of the high temperature phase (austenite) of martensitic steels 9Cr-1Mo

    International Nuclear Information System (INIS)

    Barcelo, F.; Brachet, J.C.

    1993-01-01

    In martensitic steels, the austenitic grain size before transformation may influence mechanical properties. 9Cr-1Mo steel (EM10) is used in hexagonal pipes fabrication in fast neutrons reactors. Image analysis allows to quantify the older grain size in function of the austenization heat treatment conditions. (A.B.). 2 figs

  20. Comparison on Mechanical Properties of SA508 Gr.3 Cl.1, Cl.2, and Gr.4N Low Alloy Steels for Pressure Vessels

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Min-Chul; Park, Sang-Gyu; Lee, Bong-Sang [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Lee, Ki-Hyoung [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

    2014-10-15

    In this study, microstructure and mechanical properties of SA508 Gr.3 Cl. 1, Cl.2, and Gr.4N low alloy steels are characterized to compare their properties. To evaluate the fracture toughness in the transition region, the master curve method according to ASTM E1921 was adopted in the cleavage transition region. Tensile tests and Charpy impact tests were also performed to evaluate the mechanical properties, and a microstructural investigation was carried out. The microstructure and mechanical properties of SA508 Gr.3 Cl.1, Cl2 and Gr.4N low alloy steels were characterized.. The predominant microstructure of SA508 Gr.4N model alloy is tempered martensite, while SA508 Gr.3 Cl.1 and Cl.2 steels show a typical tempered upper bainitic structure. SA508 Gr. 4N model alloy shows the best strength and transition behavior among the three SA508 steels. SA508 Gr.3 Cl.2 steel also has quite good strength, but there is a loss of toughness.

  1. Fatigue characteristics of dual-phase steel sheets

    Energy Technology Data Exchange (ETDEWEB)

    Onn, Irwan Herman; Ahmad, Norhayati; Tamin, Mohd Nasir [Universiti Teknologi Malaysia, Skudai (Malaysia)

    2015-01-15

    Fatigue characteristics of dual-phase steel sheets, commonly used in automobile body construction were established. For this purpose, a series of fatigue tests, each at constant stress amplitude were conducted on 1.2 mm-thick, dual-phase DP600 steel sheet specimens with two different load ratios of minimum-to-maximum stress, R = 0.1 and -1. The resulting fatigue behavior is expressed in terms of fatigue strength-life (S-N) curves. Fatigue behavior of the steel sheets in the high-cycle fatigue region can be represented by Basquin's equation with coefficient and exponent value of 921.2 and 0.093, respectively. An endurance limit of 255 MPa is observed. In addition, fatigue strengths of the dual-phase steel sheets display lower magnitude than their bulk counterparts. Effect of mean stress on fatigue behavior of the steel sheets is well predicted by Walker's model. Exponential calibration factor is introduced to the models by SWT, Goodman and Morrow with comparable prediction to the Walker's model.

  2. Steel fiber reinforced concrete pipes: part 1: technological analysis of the mechanical behavior

    Directory of Open Access Journals (Sweden)

    A. D. de Figueiredo

    Full Text Available This paper is the first part of an extensive work focusing the technological development of steel fiber reinforced concrete pipes (FRCP. Here is presented and discussed the experimental campaign focusing the test procedure and the mechanical behavior obtained for each of the dosages of fiber used. In the second part ("Steel fiber reinforced concrete pipes. Part 2: Numerical model to simulate the crushing test", the aspects of FRCP numerical modeling are presented and analyzed using the same experimental results in order to be validated. This study was carried out trying to reduce some uncertainties related to FRCP performance and provide a better condition to the use of these components. In this respect, an experimental study was carried out using sewage concrete pipes in full scale as specimens. The diameter of the specimens was 600 mm, and they had a length of 2500 mm. The pipes were reinforced with traditional bars and different contents of steel fibers in order to compare their performance through the crushing test. Two test procedures were used in that sense. In the 1st Series, the diameter displacement was monitored by the use of two LVDTs positioned at both extremities of the pipes. In the 2nd Series, just one LVDT is positioned at the spigot. The results shown a more rigidity response of the pipe during tests when the displacements were measured at the enlarged section of the socket. The fiber reinforcement was very effective, especially when low level of displacement was imposed to the FRCP. At this condition, the steel fibers showed an equivalent performance to superior class pipes made with traditional reinforced. The fiber content of 40 kg/m3 provided a hardening behavior for the FRCP, and could be considered as equivalent to the critical volume in this condition.

  3. Creep resistant, precipitation-dispersion-strengthened, martensitic stainless steel and method thereof

    Science.gov (United States)

    Buck, R.F.

    1994-05-10

    An iron-based, corrosion-resistant, precipitation strengthened, martensitic steel essentially free of delta ferrite for use at high temperatures has a nominal composition of 0.05--0.1 C, 8--12 Cr, 1--5 Co, 0.5--2.0 Ni, 0.41--1.0 Mo, 0.1--0.5 Ti, and the balance iron. This steel is different from other corrosion-resistant martensitic steels because its microstructure consists of a uniform dispersion of fine particles, which are very closely spaced, and which do not coarsen at high temperatures. Thus at high temperatures this steel combines the excellent creep strength of dispersion-strengthened steels, with the ease of fabricability afforded by precipitation hardenable steels. 2 figures.

  4. Creep resistant, precipitation-dispersion-strengthened, martensitic stainless steel and method thereof

    Science.gov (United States)

    Buck, Robert F.

    1994-01-01

    An iron-based, corrosion-resistant, precipitation strengthened, martensitic steel essentially free of delta ferrite for use at high temperatures has a nominal composition of 0.05-0.1 C, 8-12 Cr, 1-5 Co, 0.5-2.0 Ni, 0.41-1.0 Mo, 0.1-0.5 Ti, and the balance iron. This steel is different from other corrosion-resistant martensitic steels because its microstructure consists of a uniform dispersion of fine particles, which are very closely spaced, and which do not coarsen at high temperatures. Thus at high temperatures this steel combines the excellent creep strength of dispersion-strengthened steels, with the ease of fabricability afforded by precipitation hardenable steels.

  5. Phase transformation of the L1{sub 2} phase to kappa-carbide after spinodal decomposition and ordering in an Fe–C–Mn–Al austenitic steel

    Energy Technology Data Exchange (ETDEWEB)

    Cheng, Wei-Chun, E-mail: weicheng@mail.ntust.edu.tw [Department of Mechanical Engineering, National Taiwan University of Science and Technology, 43 Keelung Road, Section 4, Taipei 106, Taiwan (China); Cheng, Chih-Yao; Hsu, Chia-Wei [Department of Mechanical Engineering, National Taiwan University of Science and Technology, 43 Keelung Road, Section 4, Taipei 106, Taiwan (China); Laughlin, David E. [Department of Materials Science and Engineering, Carnegie Mellon University, 5000 Forbes Avenue, Pittsburgh, PA (United States)

    2015-08-26

    Fe–C–Mn–Al steels have the potential to substitute for commercial Ni–Cr stainless steels. For the development of Fe–C–Mn–Al stainless steels, phase transformations play an important role. Our methods of studying the phase transformations of the steel include heating, cooling, and/or annealing. The results of our study show that spinodal decomposition, an atomic ordering reaction and the transformation of the L1{sub 2} phase to kappa-carbide occur in the Fe–C–Mn–Al steel. After cooling, the austenite decomposes by the spinodal mechanism into solute-lean and solute-rich austenite phases. The solute-rich austenite phase also transforms into the L1{sub 2} phase via the ordering reaction upon cooling to lower temperatures. After quenching and prolonged annealing, the L1{sub 2} phase grows in the austenite and finally transforms into kappa-carbide. This L1{sub 2} phase to kappa-carbide transformation has not been observed previously.

  6. Connections: Superplasticity, Damascus Steels, Laminated Steels, and Carbon Dating

    Science.gov (United States)

    Wadsworth, Jeffrey

    2016-12-01

    In this paper, a description is given of the connections that evolved from the initial development of a family of superplastic plain carbon steels that came to be known as Ultra-High Carbon Steels (UHCS). It was observed that their very high carbon contents were similar, if not identical, to those of Damascus steels. There followed a series of attempts to rediscover how the famous patterns found on Damascus steels blades were formed. At the same time, in order to improve the toughness at room temperature of the newly-developed UHCS, laminated composites were made of alternating layers of UHCS and mild steel (and subsequently other steels and other metals). This led to a study of ancient laminated composites, the motives for their manufacture, and the plausibility of some of the claims relating to the number of layers in the final blades. One apparently ancient laminated composite, recovered in 1837 from the great pyramid of Giza which was constructed in about 2750 B.C., stimulated a carbon dating study of ancient steels. The modern interest in "Bladesmithing" has connections back to many of these ancient weapons.

  7. Fatigue behaviour of friction welded medium carbon steel and austenitic stainless steel dissimilar joints

    International Nuclear Information System (INIS)

    Paventhan, R.; Lakshminarayanan, P.R.; Balasubramanian, V.

    2011-01-01

    Research highlights: → Fusion welding of dissimilar metals is a problem due to difference in properties. → Solid state welding process such as friction welding is a solution for the above problem. → Fatigue life of friction welded carbon steel and stainless steel joints are evaluated. → Effect of notch on the fatigue life of friction welded dissimilar joints is reported. → Formation of intermetallic is responsible for reduction in fatigue life of dissimilar joints. -- Abstract: This paper reports the fatigue behaviour of friction welded medium carbon steel-austenitic stainless steel (MCS-ASS) dissimilar joints. Commercial grade medium carbon steel rods of 12 mm diameter and AISI 304 grade austenitic stainless steel rods of 12 mm diameter were used to fabricate the joints. A constant speed, continuous drive friction welding machine was used to fabricate the joints. Fatigue life of the joints was evaluated conducting the experiments using rotary bending fatigue testing machine (R = -1). Applied stress vs. number of cycles to failure (S-N) curve was plotted for unnotched and notched specimens. Basquin constants, fatigue strength, fatigue notch factor and notch sensitivity factor were evaluated for the dissimilar joints. Fatigue strength of the joints is correlated with microstructure, microhardness and tensile properties of the joints.

  8. The use of the DInSAR method in the monitoring of road damage caused by mining activities

    Science.gov (United States)

    Murdzek, Radosław; Malik, Hubert; Leśniak, Andrzej

    2018-04-01

    This paper reviews existing remote sensing methods of road damage detection and demonstrates the possibility of using DInSAR (Differential Interferometry SAR) method to identify endangered road sections. In this study two radar images collected by Sentinel-1 satellite have been used. Images were acquired with 24 days interval in 2015. The analysis allowed to estimate the scale of the post-mining deformation that occurred in Upper Silesia and to indicate areas where road infrastructure is particularly vulnerable to damage.

  9. Current status of stainless steel industry and development of stainless steel

    International Nuclear Information System (INIS)

    Lee, Yong Deuk; Lee, Chan Soo; Kim Kwang Tae

    2000-01-01

    Stainless steel is not only clean and smooth in its surface, but also it is superior in quality in terms of corrosion resistance and strength. So that, it is widely in use in the field of construction, chemical installations, and other industries. Growth of stainless steel industry started since the steel technology was developed for mass production in 1960s. Since then stainless steel industry grew rapidly on account of diversified development in this field and growth rate went up to 5.8% per year comparable to 2.3% of steel growth. The rapid growth is attributed to significant industry developments in Europe and Japan in the years of 1970s and 1980s. In addition to these the expansion of stainless steel industry in Korea and Taiwan. Presently Korea produces about 120,000 tons of stainless steel and occupies about 8% of international market. This means Korea become the second largest single country in world in stainless steel production. Moreover Korea is to reinforce its domestic production line by affiliating production companies, increasing of production capability, and specializing in types of stainless steel. This paper is to describe activity of material development, and types of stainless steel for industry use. (Hong, J. S.)

  10. Corrosion inhibition performance of 2,5-bis(4-dimethylaminophenyl)-1,3,4-oxadiazole for carbon steel in HCl solution: Gravimetric, electrochemical and XPS studies

    Energy Technology Data Exchange (ETDEWEB)

    Bouanis, M.; Tourabi, M.; Nyassi, A. [Laboratoire de Catalyse et de Corrosion des Matériaux (LCCM), Faculté des Sciences, Université Chouaib Doukkali, B.P. 20, M-24000 El Jadida (Morocco); Zarrouk, A. [LCAE-URAC 18, Faculty of Science, First Mohammed University, PO Box 717, M-60 000 Oujda (Morocco); Jama, C. [UMET-ISP, CNRS UMR 8207, ENSCL, Université Lille Nord de France, CS 90108, F-59652 Villeneuve d' Ascq Cedex (France); Bentiss, F., E-mail: fbentiss@gmail.com [Laboratoire de Catalyse et de Corrosion des Matériaux (LCCM), Faculté des Sciences, Université Chouaib Doukkali, B.P. 20, M-24000 El Jadida (Morocco); UMET-ISP, CNRS UMR 8207, ENSCL, Université Lille Nord de France, CS 90108, F-59652 Villeneuve d' Ascq Cedex (France)

    2016-12-15

    Highlights: • 2,5-Bis(4-dimethylaminophenyl)-1,3,4-oxadiazole is good corrosion inhibitor for carbon steel in 1 M HCl. • XPS analysis has provided the composition of adsorbed protective layer on the steel surface. • The adsorption of the investigated 1,3,4-oxadiazole is mainly due to chemisorption. - Abstract: Corrosion inhibition of carbon steel in normal hydrochloric acid solution at 30 °C by 2,5-bis(4-dimethylaminophenyl)-1,3,4-oxadiazole (DAPO) has been studied by weight loss measurements and electrochemical techniques (polarization and AC impedance). The experimental results showed that DAPO acted as an efficient inhibitor against the carbon steel corrosion in 1 M HCl, and its inhibition efficiency increased with the inhibitor concentration reaching a value up to 93% at 1 mM. Polarization studies showed that the DAPO was a mixed-type inhibitor. The adsorption of this 1,3,4-oxadiazole derivative on the carbon steel surface in 1 M HCl solution followed the Langmuir adsorption isotherm and the corresponding value of the standard Gibbs free energy of adsorption (ΔG°{sub ads}) is associated to a chemisorption mechanism. Scanning Electron Microscopy (SEM) and X-Ray Photoelectron Spectroscopy (XPS) analyses were carried out to characterize the chemical composition of the inhibitive film formed on the steel surface. The surfaces studies showed that the inhibitive layer is composed of an iron oxide/hydroxide mixture where DAPO molecules are incorporated. The cytotoxicity of DAPO was also determined using cell culture system.

  11. High strain rate tensile properties of annealed 2 1/4 Cr--1 Mo steel

    International Nuclear Information System (INIS)

    Klueh, R.L.; Oakes, R.E. Jr.

    1975-01-01

    The high strain rate tensile properties of annealed 2 1 / 4 Cr-1 Mo steel were determined and the tensile behavior from 25 to 566 0 C and strain rates of 2.67 x 10 -6 to 144/s were described. Above 0.1/s at 25 0 C, both the yield stress and the ultimate tensile strength increased rapidly with increasing strain rate. As the temperature was increased, a dynamic strain aging peak appeared in the ultimate tensile strength-temperature curves. The peak height was a maximum at about 350 0 C and 2.67 x 10 -6 /s. With increasing strain rate, a peak of decreased height occurred at progressively higher temperatures. The major effect of strain rate on ductility occurred at elevated temperatures, where a decrease in strain rate caused an increase in total elongation and reduction in area

  12. Influence of dynamic sodium environment on the creep-fatigue behaviour of Modified 9Cr-1Mo ferritic-martensitic steel

    International Nuclear Information System (INIS)

    Kannan, R.; Ganesan, V.; Mariappan, K.; Sukumaran, G.; Sandhya, R.; Mathew, M.D.; Bhanu Sankara Rao, K.

    2011-01-01

    Highlights: → The effects of dynamic sodium on the CFI behaviour of Mod. 9Cr-1Mo steel has investigated. → The cyclic stress response of Mod. 9Cr-1Mo steel under flowing sodium environment is similar to that of air environment. → The creep-fatigue endurance of the alloy is found to decrease with introduction of hold time and with increase in the duration of hold time and the factor of life increase in sodium compared to air environment is reduced with increase in hold time. → In contrast to air environment, tensile holds were found to be more damaging than compression hold in sodium environment. → Design rules based on air environment can be safely applied for the components operating in sodium environment. - Abstract: The use of liquid sodium as a heat transfer medium for sodium-cooled fast reactors (SFRs) necessitates a clear understanding of the effects of dynamic sodium on low cycle fatigue (LCF), creep and creep-fatigue interaction (CFI) behaviour of reactor structural materials. Mod. 9Cr-1Mo ferritic steel is the material of current interest for the steam generator components of sodium cooled fast reactors. The steam generator has a design life of 30-40 years. The effects of dynamic sodium on the LCF and CFI behaviour of Mod. 9Cr-1Mo steel have been investigated at 823 and 873 K. The CFI life of the steel showed marginal increase under flowing sodium environment when compared to air environment. Hence, the design rules for creep-fatigue interaction based on air tests can be safely applied for components operating in sodium environment. This paper attempts to explain the observed LCF and CFI results based on the detailed metallography and fractography conducted on the failed samples.

  13. Water requirements of the iron and steel industry

    Science.gov (United States)

    Walling, Faulkner B.; Otts, Louis Ethelbert

    1967-01-01

    Twenty-nine steel plants surveyed during 1957 and 1958 withdrew from various sources about 1,400 billion gallons of water annually and produced 40.8 million tons of ingot steel. This is equivalent to about 34,000 gallons of water per ton of steel. Fifteen iron ore mines and fifteen ore concentration plants together withdrew annually about 89,000 million gallons to produce 15 million tons of iron ore concentrate, or 5,900 gallons per ton of concentrate. About 97 percent of the water used in the steel plants came from surface sources, 2.2 percent was reclaimed sewage, and 1.2 percent was ground water. Steel plants supplied about 96 percent of their own water requirements, although only three plants used self-supplied water exclusively. Water used by the iron ore mines and concentration plants was also predominantly self supplied from surface source. Water use in the iron and steel industry varied widely and depended on the availability of water, age and condition of plants and equipment, kinds of processes, and plant operating procedures. Gross water use in integrated steel plants ranged from 11,200 to 110,000 gallons per ton of steel ingots, and in steel processing plants it ranged from 4,180 to 26,700 gallons per ton. Water reuse also varied widely from 0 to 18 times in integrated steel plants and from 0 to 44 times in steel processing plants. Availability of water seemed to be the principal factor in determining the rate of reuse. Of the units within steel plants, a typical (median) blast furnace required 20,500 gallons of water per ton of pig iron. At the 1956-60 average rate of pig iron consumption, this amounts to about 13,000 gallons per ton of steel ingots or about 40 percent of that required by a typical integrated steel plant 33,200 gallons per ton. Different processes of iron ore concentration are devised specifically for the various kinds of ore. These processes result in a wide range of water use from 124 to 11,300 gallons of water per ton of iron ore

  14. Dinámica institucional de la Representación. Individualismo y partidos en la Cámara de Diputados

    Directory of Open Access Journals (Sweden)

    Carlos Alberto MARQUÉS NOVAES

    2009-11-01

    Full Text Available RESUMEN: Determinados rasgos históricos de las instituciones políticas brasileñas -forma de gobierno y sistema electoral principalmente-inciden en la dinámica interna del Congreso. El autor analiza como se desarrollan las diversas actividades vinculadas a la producción legislativa y pone en evidencia una dinámica individualista que anula la posibilidad de desarrollar estrategias cooperativas. No obstante, el estudio de las votaciones sobre determinadas cuestiones niega la hipótesis de que esta dinámica elimine la existencia de un posicionamiento ideológico dentro del Congreso sobre el eje izquierda-derecha.ABSTRACT: It is analyzed how specific historical features of brazilean political institutions -specially, type of government and electoral system- influence in the internal dynamic of Congress. The author analyzes the process of legislative production and underlines an individualistic dynamic which cancel the possibility to develop cooperative strategies. However, the study possibility to develop cooperative strategies. However, the study of votings about specific questions denyes the hypothesis which sets up that this kind of dynamic eliminates the existence of an ideological position inside the Congress in the axis left-right.

  15. Percepción de la persona con obesidad sobre su dinámica familiar, Cuenca. 2016

    OpenAIRE

    Mora Verdugo, Miriann Alexandra

    2017-01-01

    Antecedente: Al analizar la familia no se trata de adoptar el concepto de la cultura occidental que indica es un grupo formado por marido, mujer e hijos 1. La familia es vista como un sistema, padres e hijos son subsistemas que interactúan2. Muchas veces esta parte es invisible. Distintas disciplinas han estudiado a la familia pero los resultados que presentan son fragmentados3. No se analiza a profundidad la dinámica familiar, en su estructura, su tipología, jerarquía, roles, holones, triang...

  16. Una aproximación metodológica para el modelamiento organizacional bajo un enfoque de dinámica de sistemas

    OpenAIRE

    Arango Serna, Martin Darío

    1997-01-01

    EI objetivo de este trabajo es elaborar unas paulas metodológicas basadas en dinámica de sistemas que permitan experimentar estrategias de cambia en las organizaciones. Es un proyecto de investigaci6n que surge ante la necesidad de involucrar en los procesos del modelamiento organizacional el pensamiento sistémico conjuntamente con la dinámica de sistemas, como una herramienta ágil para la toma de decisiones en las políticas gerenciales del mundo empresarial moderno. EI pensamiento de...

  17. Tensile behavior of irradiated manganese-stabilized stainless steel

    Energy Technology Data Exchange (ETDEWEB)

    Klueh, R.L. [Oak Ridge National Lab., TN (United States)

    1996-10-01

    Tensile tests were conducted on seven experimental, high-manganese austenitic stainless steels after irradiation up to 44 dpa in the FFTF. An Fe-20Mn-12Cr-0.25C base composition was used, to which various combinations of Ti, W, V, B, and P were added to improve strength. Nominal amounts added were 0.1% Ti, 1% W, 0.1% V, 0.005% B, and 0.03% P. Irradiation was carried out at 420, 520, and 600{degrees}C on the steels in the solution-annealed and 20% cold-worked conditions. Tensile tests were conducted at the irradiation temperature. Results were compared with type 316 SS. Neutron irradiation hardened all of the solution-annealed steels at 420, 520, and 600{degrees}C, as measured by the increase in yield stress and ultimate tensile strength. The steel to which all five elements were added to the base composition showed the least amount of hardening. It also showed a smaller loss of ductility (uniform and total elongation) than the other steels. The total and uniform elongations of this steel after irradiation at 420{degrees}C was over four times that of the other manganese-stabilized steels and 316 SS. There was much less difference in strength and ductility at the two higher irradiation temperatures, where there was considerably less hardening, and thus, less loss of ductility. In the cold-worked condition, hardening occured only after irradiation at 420{degrees}C, and there was much less difference in the properties of the steels after irradiation. At the 420{degrees}C irradiation temperature, most of the manganese-stabilized steels maintained more ductility than the 316 SS. After irradiation at 420{degrees}C, the temperature of maximum hardening, the steel to which all five of the elements were added had the best uniform elongation.

  18. Desempenho do equilíbrio dinâmico de escolares ouvintes e com perda auditiva sensorioneural

    Directory of Open Access Journals (Sweden)

    Renato de Souza Melo

    2014-12-01

    Full Text Available Introdução: O equilíbrio corporal humano é regulado pela atuação sensorial do sistema vestibular, situado na orelha interna. Crianças com perda auditiva sensorioneural podem apresentar alterações no sistema vestibular e, consequentemente, no equilíbrio corporal, em decorrência da lesão na orelha interna. Objetivos: Avaliar o equilíbrio dinâmico em escolares ouvintes e com perda auditiva sensorioneural e comparar os dados entre os grupos considerando os sexos e as faixas etárias. Métodos: Estudo de corte transversal, que avaliou 96 escolares, sendo 48 ouvintes e 48 com perda auditiva sensorioneural, de ambos os sexos, na faixa etária entre sete e 18 anos. A avaliação do equilíbrio dinâmico foi realizada por meio do teste de Babinski-Weil e do teste de Fukuda. Para a análise dos dados foi utilizado o teste do qui-quadrado de Pearson, tendo em vista a distribuição de normalidade dos dados. Resultados: Os escolares com perda auditiva apresentaram maior ocorrência de alterações no equilíbrio dinâmico comparado aos ouvintes: teste de Babinski-Weil e teste de Fukuda: (p<0,001. A mesma diferença foi observada quando os voluntários foram agrupados pelos sexos: feminino e masculino: teste de Babinski-Weil e teste de Fukuda: (p<0,001. Estratificando-se pelas faixas etárias, os resultados apontaram diferenças, entre todos os grupos etários avaliados: teste de Babinski-Weil: sete a 14 anos: (p<0,001 e 15-18 anos: (p= 0,004, teste de Fukuda: sete a 18 anos: (p<0,001. Conclusão: Os escolares com perda auditiva apresentaram maior ocorrência de alterações no equilíbrio dinâmico que os ouvintes do mesmo sexo e faixa etária.

  19. Development of nuclear grade stainless steels at KCSSL

    International Nuclear Information System (INIS)

    Balachandran, G.; Dhere, M.; Mahadik, A.; Hinge, N.M.; Balasubramanian, V.

    2011-01-01

    Kalyani Carpenter Special Steels Ltd is an alloy steel plant, where a variety of alloy steel grades are produced for automotive, defence, nuclear and aerospace applications. The plant has developed expertise in processing of several alloy steel grades of superior quality that meets stringent specifications. Primary steel is processed through a combination of electric arc furnace, ladle furnace and vacuum degassing where stringent control over dephosphorisation, desulphurization, deoxidation is effected to get a refined high quality steel. The molten steel is cast through continuous casting of slabs or ingot casting. In grades specific to nuclear application, the primary cast products are further subjected to electroslag remelting to achieve further freedom from inclusions and to achieve a favourable solidification grain structure, which ultimately improve the hot workability of the alloy steel. Appropriate choice of slag and operating parameters are needed for realising the required ingot quality. The present study would examine the processing and quality aspects of some important grades of steels used in nuclear industry namely ferritic 9Cr-1Mo steel, martensitic stainless steels 403, 410, precipitation hardenable 17-4 PH stainless steel and austenitic 321, 316LN stainless steel, which were made and supplied for applications to Indian nuclear industry. The expertise developed in processing the steels in terms of melting, heat treatment and their relationship to structural features and mechanical properties would be highlighted. (author)

  20. Heat affected zone structure in welded joints of 15Kh1M1FL, 25Kh2NMFA and 20KhN2MFA steels

    International Nuclear Information System (INIS)

    Levenberg, N.E.; German, S.I.; Fomina, O.P.; Netesa, E.M.; Tsaryuk, A.K.; Kornienko, T.A.

    1983-01-01

    Heat affected zone (HAZ) structure of thick-walled, nature joints of 15Kh1M1FL steel for block structure of power reactors and 25Kh2NMFA and 20KhN2MFA steels for rotors - is investigated. Multi-layer arc welding is performed under conditions being created for standard components of turbines. Thermokinetics diagrams of austenite decomposition are built, phase composition and character of the structure forming at HAZ in the process of welding with preheating are studied. It is shown that at HAZ in joints of the steels under consideration in the process of welding with preheating is formed a structure of a grained bainite which is uniform in its structure and phase composition. Small volumes of round and elongated forms consisting of martensite and residual austenite are distributed in α-solid solution of the bainite. The bainite of the HAZ in welded joints possesses high hardness and great stability in the process of tempering

  1. Simple Heat Treatment for Production of Hot-Dip Galvanized Dual Phase Steel Using Si-Al Steels

    Science.gov (United States)

    Equihua-Guillén, F.; García-Lara, A. M.; Muñíz-Valdes, C. R.; Ortíz-Cuellar, J. C.; Camporredondo-Saucedo, J. E.

    2014-01-01

    This work presents relevant metallurgical considerations to produce galvanized dual phase steels from low cost aluminum-silicon steels which are produced by continuous strip processing. Two steels with different contents of Si and Al were austenized in the two-phase field ferrite + austenite (α + γ) in a fast manner to obtain dual phase steels, suitable for hot-dip galvanizing process, under typical parameters of continuous annealing processing line. Tensile dual phase properties were obtained from specimens cooled from temperature below Ar3, held during 3 min, intermediate cooling at temperature above Ar1 and quenching in Zn bath at 465 °C. The results have shown typical microstructure and tensile properties of galvanized dual phase steels. Finally, the synergistic effect of aluminum, silicon, and residual chromium on martensite start temperature ( M s), critical cooling rate ( C R), volume fraction of martensite, and tensile properties has been studied.

  2. Opuntia ficus-indica Extract as Green Corrosion Inhibitor for Carbon Steel in 1 M HCl Solution

    Directory of Open Access Journals (Sweden)

    J. P. Flores-De los Ríos

    2015-01-01

    Full Text Available The effect of Opuntia ficus-indica (Nopal as green corrosion inhibitor for carbon steel in 1 M HCl solution has been investigated by using weight loss tests, potentiodynamic polarization curves, and electrochemical impedance spectroscopy measurements. Also, scanning electron microscopy (SEM and Fourier transform infrared spectroscopy (FT-IR analysis were performed. The inhibitor concentrations used ranged from 0 to 300 ppm at 25, 40, and 60°C. Results indicated the inhibition efficiency increases with increasing extract concentration and decreases with the temperature, and the inhibitor acted as a cathodic-type inhibitor which is physically absorbed onto the steel surface. In fact, the adsorption of the inhibitor on the steel surface follows the Langmuir adsorption isotherm, indicating monolayer adsorption. The presence of heteroatoms such as C, N, and O and OH groups were responsible for the corrosion inhibition.

  3. Corrosion of martensitic steels in flowing 17Li83Pb alloy

    International Nuclear Information System (INIS)

    Flament, T.; Fauvet, P.; Hocde, B.; Sannier, J.

    1988-01-01

    Corrosion of three martensitic steels - 1.4914, HT9 and T91 - in the presence of flowing 17Li83Pb is investigated in thermal convection loops Tulip entirely made of 1.4914 steel. Two 3000-hour tests were performed at maximal temperatures of respectively 450 and 475 0 C with a δT of 60 0 C and an alloy velocity of about 0.08 m.s -1 . In both tests, corrosion is characterized by an homogeneous dissolution of the steel without formation of a corrosion layer. Corrosion rate is constant and very temperature dependent: the sound-metal loss of 1.4914 steel is 22 μm. year -1 at 450 0 C and 40 μm.year -1 at 475 0 C. Behaviours of 1.4914 and HT9 steels are very similar whereas T91 steel is about 20% less corroded

  4. Dinâmica de redes de osciladores de Fitzhugh-Nagumo

    OpenAIRE

    Santos, Juliana Vicente dos

    2013-01-01

    O modelo de Fitzhugh-Nagumo é composto originalmente por um sistema de duas equações diferenciais não-lineares, que simulam o comportamento de condução do impulso nervoso através da membrana neural. Neste trabalho estudamos numericamente o comportamento dinâmico de redes de neurônios acoplados, modeladas pelas equações de Fitzhugh-Nagumo. Consideramos redes de dois, três e quatro neurônios acoplados unidirecionalmente e bidirecionalmente, para as quais foram construídos espaços de parâmetros ...

  5. Irradiation creep in ferritic steels

    International Nuclear Information System (INIS)

    Vandermeulen, W.; Bremaecker, A. de; Burbure, S. de; Huet, J.J.; Asbroeck, P. van

    Pressurized and non-pressurized capsules of several ferritic steels have been irradiated in Rapsodie between 400 and 500 0 C up to 3.7 x 10 22 n/cm 2 (E>0.1 MeV). Results of the diameter measurements are presented and show that the total in-pile deformation is lower than for austenitic steels

  6. The integrity of 9Cr-1Mo to stainless steel transition joints in AGR steam generators

    International Nuclear Information System (INIS)

    James, D.W.; Neumann, P.; Soo, J.

    1982-01-01

    The metallurgical aspects of the transition joint between 9Cr-1Mo and 316 stainless steel boiler tube sections are reviewed. A large minimum superheat margin (106 0 C) between the dryout zone and the 9Cr-1Mo to stainless steel transition joint was specified in the original design to eliminate the risk of wetting the stainless steel which is susceptible to stress corrosion cracking. However, small defects were discovered in the welds between the 9Cr-1Mo and Sanicro (72%Ni-16%Cr-10%Fe) transition piece, resulting from dilution of the weld pool by nickel from the transition piece. This led to the possibility of weld failure as a result of creep crack growth in service, and any significant reduction in operating temperature would mean that the large superheat margin could not be sustained. The creep properties of the joints, together with the transition joint temperature distribution, enabled tube failure rates to be determined as a function of operating temperature. A probabilistic model was developed so that the transition joint could be operated within a temperature 'window', the lower temperature limit being determined by stress corrosion considerations and the upper limit being set by creep rate limitations. This allows full load performance from the boilers throughout the anticipated life of the plant. (author)

  7. Borated stainless steel storage project to the spent fuel of the IEA-R1 reactor

    International Nuclear Information System (INIS)

    Rodrigues, Antonio Carlos Iglesias; Madi Filho, Tufic; Ricci Filho, Walter

    2013-01-01

    The IEA-R1 research reactor operates in a regimen of 64h weekly, at the power of 4.5 MW. In these conditions, the racks to the spent fuel elements have less than half of its initial capacity. Thus, maintaining these operating circumstances, the storage will have capacity for approximately six years. Whereas the estimated useful life of the IEA-R1 is around twenty years, it will be necessary to increase the storage capacity for the spent fuel. Dr. Henrik Grahn, expert of the International Atomic Energy Agency on wet storage, visiting the IEA-R1 Reactor (September/2012) made some recommendations: among them, the design and installation of racks made with borated stainless steel and internally coated with an aluminum film, so that corrosion of the fuel elements would not occur. This work objective is the project of high capacity storage for spent fuel elements, using borated stainless steel, to answer the Reactor IEA-R1 demand and the security requirements of the International Atomic Energy Agency. (author)

  8. Borated stainless steel storage project to the spent fuel of the IEA-R1 reactor

    Energy Technology Data Exchange (ETDEWEB)

    Rodrigues, Antonio Carlos Iglesias; Madi Filho, Tufic; Ricci Filho, Walter, E-mail: acirodri@ipen.br, E-mail: tmfilho@ipen.br, E-mail: wricci@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2013-07-01

    The IEA-R1 research reactor operates in a regimen of 64h weekly, at the power of 4.5 MW. In these conditions, the racks to the spent fuel elements have less than half of its initial capacity. Thus, maintaining these operating circumstances, the storage will have capacity for approximately six years. Whereas the estimated useful life of the IEA-R1 is around twenty years, it will be necessary to increase the storage capacity for the spent fuel. Dr. Henrik Grahn, expert of the International Atomic Energy Agency on wet storage, visiting the IEA-R1 Reactor (September/2012) made some recommendations: among them, the design and installation of racks made with borated stainless steel and internally coated with an aluminum film, so that corrosion of the fuel elements would not occur. This work objective is the project of high capacity storage for spent fuel elements, using borated stainless steel, to answer the Reactor IEA-R1 demand and the security requirements of the International Atomic Energy Agency. (author)

  9. Cancer incidence among mild steel and stainless steel welders and other metal workers

    DEFF Research Database (Denmark)

    Hansen, K S; Lauritsen, J M; Skytthe, A

    1996-01-01

    by a postal questionnaire in living cohort members and interviews by proxy for deceased and emigrated subjects. The incidence of lung cancer was increased among workers ever "employed as welders" (SIR = 1.38, 95% C.I. 1.03-1.81). There was a significant excess risk of lung cancer among "mild steel (MS) only...... "stainless steel (SS) only welders" (SIR = 2.38, 95% C.I. 0.77-5.55). In spite of signs of inconsistency in the risk estimation by duration and latency, we find the results support the conclusions of other studies: employment as a welder is associated with an increased lung cancer risk....

  10. Stability of ferritic steel to higher doses: Survey of reactor pressure vessel steel data and comparison with candidate materials for future nuclear systems

    International Nuclear Information System (INIS)

    Blagoeva, D.T.; Debarberis, L.; Jong, M.; Pierick, P. ten

    2014-01-01

    This paper is illustrating the potential of the well-known low alloyed clean steels, extensively used for the current light water Reactor Pressure Vessels (RPV) steels, for a likely use as a structural material also for the new generation nuclear systems. This option would provide, especially for large components, affordable, easily accessible and a technically more convenient solution in terms of manufacturing and joining techniques. A comprehensive comparison between several sets of surveillance and research data available for a number of RPV clean steels for doses up to 1.5 dpa, and up to 12 dpa for 9%Cr steels, is carried out in order to evaluate radiation stability of the currently used RPV clean steels even at higher doses. Based on the numerous data available, positive preliminary conclusions are drawn regarding the eventual use of clean RPV steels for the massive structural components of the new reactor systems. - Highlights: • Common embrittlement trend between RPV and advanced steels till intermediate doses. • For doses >1.5 dpa, damage rate saturation tendency is observed for RPV steels. • RPV steels might be conveniently utilised also outside their foreseen dose range

  11. Plasma-induced surface degradation in 304 stainless steel used for TRIAM-1M limiter

    International Nuclear Information System (INIS)

    Tsukuda, N.; Kuramoto, E.; Tokunaga, K.; Muroga, T.; Yoshida, N.; Itoh, S.

    1994-01-01

    Surface degradation in a 304 stainless steel limiter of TRIAM-1M by long-pulse discharge during long period operation has been examined by means of X-ray diffraction, scanning electron microscopy and dynamical microindentation tests. Particular exfoliation and hardening of the surface of the electron drift side were observed. These result from the formation of α prime martensite induced by hydrogen in the plasma. The stability of the martensitic phase has been studied by annealing experiments on the cathodically hydrogen charged 316 stainless steel by X-ray diffraction. Both ε and α prime martensites were formed by 22 h cathodic charging. The former reverts to γ-phase and/or converts to α prime martensite below 723 K and the latter reverts to γ-phase below 923 K, repectively. ((orig.))

  12. Ultrahigh Ductility, High-Carbon Martensitic Steel

    Science.gov (United States)

    Qin, Shengwei; Liu, Yu; Hao, Qingguo; Zuo, Xunwei; Rong, Yonghua; Chen, Nailu

    2016-10-01

    Based on the proposed design idea of the anti-transformation-induced plasticity effect, both the additions of the Nb element and pretreatment of the normalization process as a novel quenching-partitioning-tempering (Q-P-T) were designed for Fe-0.63C-1.52Mn-1.49Si-0.62Cr-0.036Nb hot-rolled steel. This high-carbon Q-P-T martensitic steel exhibits a tensile strength of 1890 MPa and elongation of 29 pct accompanied by the excellent product of tensile and elongation of 55 GPa pct. The origin of ultrahigh ductility for high-carbon Q-P-T martensitic steel is revealed from two aspects: one is the softening of martensitic matrix due to both the depletion of carbon in the matensitic matrix during the Q-P-T process by partitioning of carbon from supersaturated martensite to retained austenite and the reduction of the dislocation density in a martensitic matrix by dislocation absorption by retained austenite effect during deformation, which significantly enhances the deformation ability of martensitic matrix; another is the high mechanical stability of considerable carbon-enriched retained austenite, which effectively reduces the formation of brittle twin-type martensite. This work verifies the correctness of the design idea of the anti-TRIP effect and makes the third-generation advanced high-strength steels extend to the field of high-carbon steels from low- and medium-carbon steels.

  13. Comportamiento mecánico y dinámico de una mezcla asfáltica con adición de fibras

    Directory of Open Access Journals (Sweden)

    Oscar Javier Reyes Ortiz

    2005-01-01

    Full Text Available El artículo refiere el análisis experimental en el laboratorio, del efecto de la adición de fibras de polipropileno por vía seca (reemplazo de material granular por fibra sobre las propiedades mecánicas y dinámicas de una mezcla. Inicialmente se caracteriza el material granular y asfalto CA60/70, se realiza el diseño de la mezcla asfáltica de granulometría 0/10 (IDU RSV 2002 y asfalto de acuerdo con la metodología Marshall; se evalúa el efecto de fibras sobre las propiedades mecánicas mediante la evaluación de la estabilidad y fluencia, y dinámicamente por su valor de deformación permanente y modulo dinámico. Los resultados muestran un efecto positivo de las fibras en la modificación de la mezcla asfáltica. El modulo dinámico aumenta en un 45% promedio en un porcentaje de adición de 0.60%; la deformación permanente disminuye en 27.6% para una adición de fibras de 0.60% y 48.8% para la adición de fibras de 0.75%, respectivamente. Este comportamiento refleja otra alternativa eficaz para mejorar la mezcla asfáltica, aumentando la resistencia a la disgregación por efecto abrasivo del tráfico y retardando el inicio y propagación del agrietamiento por ahuellamiento

  14. Compatibility tests of steels in flowing liquid lead-bismuth

    International Nuclear Information System (INIS)

    Barbier, F.; Benamati, G.; Fazio, C.; Rusanov, A.

    2001-01-01

    The behaviour of steels exposed to flowing Pb-55Bi was evaluated. The materials tested are the two austenitic steels AISI 316L and 1.4970, and the six martensitic steels Optifer IVc, T91, Batman 27, Batman 28, EP823 and EM10 which were exposed to flowing Pb-55Bi for 1000, 2000 and 3000 h and at two temperatures (573 and 743 K). The corrosion tests were conducted in the non-isothermal loop of IPPE-Obninsk under a controlled oxygen level (10 -6 wt%). The compatibility study showed that at a lower temperature, a very thin oxide layer (<1 μm) was formed on the steels. At higher temperature, austenitic steels also exhibited a thin oxide layer sufficient to prevent their dissolution in the melt. A thicker oxide, which grew according to a parabolic law, was observed on the surface of the martensitic steels. The oxidation resistance behaviour of the martensitic steels was correlated with their alloying elements

  15. Erosion behaviour of hydro turbine steels

    Indian Academy of Sciences (India)

    WINTEC

    creases grain size hardening (Ikegami and Nemoto 1996). Nitrogen solubility ... 116. Table 1. Chemical composition of 13/4 martensitic and 21–4–N nitronic steel (wt %). Steel. C. Si Mn. Cr. Ni. N. S ..... In Fe–Cr–Ni alloys, Schramm and Reed ...

  16. Influence of austenitisation temperature on the structure and properties of weather resistant steels

    International Nuclear Information System (INIS)

    Prasad, S.N.; Mediratta, S.R.; Sarma, D.S.

    2003-01-01

    The influence of austenitisation temperature on the structure and properties of three experimental weather resistant steels has been studied. All these steels contain 1% Mn, 0.3% Ni, 0.47% Cr and 0.47% Cu. In addition, steel no. 1 has 0.1% C, 0.1% P, steel no. 2 has 0.1% C, 0.05% P and 0.024% Nb while steel 3 has 0.2% C, 0.054% Nb and 0.046% V. It has been found that the hardness, yield strength and tensile strength do not change significantly with austenitisation temperature over the range 900-1200 deg. C for steel no. 1 but they increase considerably when austenitised above 1000 deg. C for steels 2 and 3. Similarly, the ductility decreases with increasing temperature of austenitisation. All the steels austenitised up to 1000 deg. C exhibit sharp yield points. None of these steels shows sharp yield point after 1200 deg. C. At 1100 deg. C, however, sharp yield points were observed in steels 1 and 2. There has been a noticeable change in optical microstructure. In steels 2 and 3 the pearlite is gradually replaced by granular bainite when austenitised above 1000 deg. C. The transmission electron microscopy study reveals that the granular bainite consists of acicular ferrite and martensite/austenite constituent

  17. Comparison of the mechanical strength properties of several high-chromium ferritic steels

    International Nuclear Information System (INIS)

    Booker, M.K.; Sikka, V.K.; Booker, B.L.P.

    1981-01-01

    A modified 9 Cr-1 Mo ferritic steel has been selected as an alternative material for breeder reactors. Different 9 Cr-1 Mo steels are already being used commercially in UK and USA and a 9 Cr-2 Mo steel (EM12) is being used commercially in France. The 12% Cr steel alloy HT9 is also often recommended for high-temperature service. Creep-rupture data for all six seels were analyzed to yield rupture life as a function of stress, temperature, and lot-to-lot variations. Yield and tensile strength data for the three 9 Cr-1 Mo materials were also examined. All results were compared with Type 304 stainless steel, and the tensile and creep properties of the modified and British 9 Cr-1 Mo materials were used to calculate allowable stress values S 0 per Section VIII, Division 1 and S/sub m/ per code Case N-47 to section III of the ASME Boiler and Pressure Vessel Code. these values were compared with code listings for American commercial 9 Cr-1 Mo steel, 2 1/4 Cr-1 Mo steel, and Type 304 stainless steel. The conclusion is made that the modified 9 Cr-1 Mo steel displays tensile and creep strengths superior to those of the other ferritic materials examined and is at least comparable to Type 304 stainless steel from room temperature to about 625 0 C. 31 figures

  18. A two-stage constitutive model of X12CrMoWVNbN10-1-1 steel during elevated temperature

    Science.gov (United States)

    Zhu, Luobei; He, Jianli; Zhang, Ying

    2018-02-01

    In order to clarify the competition between work hardening (WH) caused by dislocation movements and the dynamic softening result from dynamic recovery (DRV) and dynamic recrystallization (DRX), a new two-stage flow stress model of X12CrMoWVNbN10-1-1 (X12) ferrite heat-resistant steel was established to describe the whole hot deformation behavior. And the parameters were determined by the experimental data operated on a Gleeble-3800 thermo- mechanical simulation. In this constitutive model, a single internal variable dislocation density evolution model is used to describe the influence of WH and DRV to flow stress. The DRX kinetic dynamic model can express accurately the contribution of DRX to the decline of flow stress, which was established on the Avrami equation. Furthermore, The established new model was compared with Fields-Bachofen (F-B) model and experimental data. The results indicate the new two-stage flow stress model can more accurately represent the hot deformation behavior of X12 ferrite heat-resistant steel, and the average error is only 0.0995.

  19. Effects of heat input on mechanical properties of metal inert gas welded 1.6 mm thick galvanized steel sheet

    International Nuclear Information System (INIS)

    Rafiqul, M I; Ishak, M; Rahman, M M

    2012-01-01

    It is usually a lot easier and less expensive to galvanize steel before it is welded into useful products. Galvanizing afterwards is almost impossible. In this research work, Galvanized Steel was welded by using the ER 308L stainless steel filler material. This work was done to find out an alternative way of welding and investigate the effects of heat input on the mechanical properties of butt welded joints of Galvanized Steel. A 13.7 kW maximum capacity MIG welding machine was used to join 1.6 mm thick sheet of galvanized steel with V groove and no gap between mm. Heat inputs was gradually increased from 21.06 to 25.07 joules/mm in this study. The result shows almost macro defects free welding and with increasing heat input the ultimate tensile strength and welding efficiency decrease. The Vickers hardness also decreases at HAZ with increasing heat input and for each individual specimen; hardness was lowest in heat affected zone (HAZ), intermediate in base metal and maximum in welded zone. The fracture for all specimens was in the heat affected zone while testing in the universal testing machine.

  20. Effects of heat input on mechanical properties of metal inert gas welded 1.6 mm thick galvanized steel sheet

    Science.gov (United States)

    Rafiqul, M. I.; Ishak, M.; Rahman, M. M.

    2012-09-01

    It is usually a lot easier and less expensive to galvanize steel before it is welded into useful products. Galvanizing afterwards is almost impossible. In this research work, Galvanized Steel was welded by using the ER 308L stainless steel filler material. This work was done to find out an alternative way of welding and investigate the effects of heat input on the mechanical properties of butt welded joints of Galvanized Steel. A 13.7 kW maximum capacity MIG welding machine was used to join 1.6 mm thick sheet of galvanized steel with V groove and no gap between mm. Heat inputs was gradually increased from 21.06 to 25.07 joules/mm in this study. The result shows almost macro defects free welding and with increasing heat input the ultimate tensile strength and welding efficiency decrease. The Vickers hardness also decreases at HAZ with increasing heat input and for each individual specimen; hardness was lowest in heat affected zone (HAZ), intermediate in base metal and maximum in welded zone. The fracture for all specimens was in the heat affected zone while testing in the universal testing machine.

  1. Compactibility of atomized high-speed steel and steel 3 powders

    International Nuclear Information System (INIS)

    Kulak, L.D.; Gavrilenko, A.P.; Pikozh, A.P.; Kuz'menko, N.N.

    1985-01-01

    Spherical powders and powders of lammellar-scaly shape of high-speed R6M5K5 steel and steel 3 produced by the method of centrifugal atomization of a rotating billet under conditions of cold pressing in steel moulds are studied for thier compactability. Compacting pressure dependnences are establsihed for density of cold-pressed compacts of spherical and scaly powders. The powders of lammellar-scaly shape both of high-speed steel and steel 3 are found to possess better compactibility within a wide range of pressures as compared to powders of spherical shape. Compacts of the lammellar-scaly powders possess also higher mechanical strength

  2. New 1H-pyrrole-2,5-dione derivatives as efficient organic inhibitors of carbon steel corrosion in hydrochloric acid medium: Electrochemical, XPS and DFT studies

    International Nuclear Information System (INIS)

    Zarrouk, A.; Hammouti, B.; Lakhlifi, T.; Traisnel, M.; Vezin, H.; Bentiss, F.

    2015-01-01

    Highlights: • 1H-pyrrole derivatives act as good corrosion inhibitors for carbon steel in 1 M HCl. • Adsorption of the inhibitors on carbon steel surface obeys Langmuir’s isotherm. • XPS showed that the inhibitors are chemisorbed on the metal surface. • Quantum chemical parameters were correlated with experimental results. - Abstract: New 1H-pyrrole-2,5-dione derivatives, namely 1-phenyl-1H-pyrrole-2,5-dione (PPD) and 1-(4-methylphenyl)-1H-pyrrole-2,5-dione (MPPD) were synthesised and their inhibitive action against the corrosion of carbon steel in 1 M HCl solution were investigated at 308 K by weight loss, potentiodynamic polarization curves, and electrochemical impedance spectroscopy (EIS) methods. The results showed that the investigated 1H-pyrrole-2,5-dione derivatives are good corrosion inhibitors for carbon steel in 1 M HCl medium, their inhibition efficiency increased with inhibitor concentration, and MPPD is slightly more effective than PPD. Potentiostatic polarization study showed that PPD and MPPD are mixed-type inhibitors in 1 M HCl. Impedance experimental data revealed a frequency distribution of the capacitance, simulated as constant phase element. The results obtained from electrochemical and weight loss studies were in reasonable agreement. The adsorption of MPPD and PPD on steel surface obeyed Langmuir’s adsorption isotherm. Thermodynamic data and XPS analysis clearly indicated that the adsorption mechanism of 1H-pyrrole-2,5-dione derivatives on carbon steel surface in 1 M HCl solution is mainly controlled by a chemisorption process. Quantum chemical calculations using the Density Functional Theory (DFT) were performed on 1H-pyrrole-2,5-dione derivatives to determine the relationship between molecular structures and their inhibition efficiencies

  3. Educação para o uso da internet - uma abordagem através das dinâmicas de grupo

    OpenAIRE

    Tinoco, Rui

    2013-01-01

    Coletânea de dinâmicas de grupo que aborda o tema de um uso saudável da interenet. Através de diversas perspetivas e temas aborda-se várias áreas e práticas usuais. As dinâmicas de grupo destinam-se não apenas aos mais novos mas também a professores e educadores em geral. A obra pretende assim ser uma ferramenta para todo aquele que pretenda estudar e intervir sobre a temática do uso saudável da internet.

  4. Long-term deformation analysis of historical buildings through the advanced SBAS-DInSAR technique: the case study of the city of Rome, Italy

    International Nuclear Information System (INIS)

    Zeni, G; Bonano, M; Casu, F; Manunta, M; Manzo, M; Pepe, A; Lanari, R; Marsella, M

    2011-01-01

    Monitoring of deformation phenomena affecting urban areas and man-made structures is of key relevance for the preservation of the artistic, archaeological and architectural heritage. The differential SAR interferometry (DInSAR) technique has already been demonstrated to be an effective tool for non-invasive deformation analyses over large areas by producing spatially dense deformation maps with centimetre to millimetre accuracy. Moreover, by exploiting long sequences of SAR data acquired by different sensors, the advanced DInSAR technique referred to as the small baseline subset (SBAS) approach allows providing long-term deformation time series, which are strategic for guaranteeing the monitoring of urban area displacements. In this work, we investigate the effectiveness of the two-scale multi-sensor SBAS-DInSAR approach to detect and monitor displacements affecting historical and artistic monuments. The presented results, achieved by applying the full resolution SBAS technique to a huge set of ERS-1/2 and ENVISAT data, spanning the 1992–2010 time interval and relevant to the city of Rome (Italy), show the capability of this approach to detect and analyse the temporal evolution of possible deformation phenomena affecting historical buildings and archaeological sites. Accordingly, our analysis demonstrates the effectiveness of the full resolution multi-sensor SBAS approach to operate as a surface deformation tool for supporting the study and conservation strategies of the historical, cultural and artistic heritage

  5. East/west steels for reactor pressure vessels

    International Nuclear Information System (INIS)

    Davies, M.; Kryukov, A.; Nikolaev, Y.; English, C.

    1997-01-01

    The report consist of three parts dealing with comparison of the irradiation behaviour of 'Eastern' and 'Western' steels, mechanisms of irradiation embrittlement and the role of compositional variations on the irradiation sensitivity of pressure vessels. Nickel, copper and phosphorus are the elements rendering the most essential influence on behaviour of pressure vessel steels under irradiation and subsequent thermal annealing. For WWER-440 reactor pressure vessel (RPV) steels in which nickel content does nor exceed 0.3% the main affecting factors are phosphorous and copper. For WWER-1000 RPV welds in which nickel content generally exceed 1.5% the role of nickel in radiation embrittlement is decisive. In 'Western' type steels main influencing elements are nickel and copper. The secondary role of phosphorus in radiation embrittlement of 'Western' steels is caused by lower relative content compared to 'Eastern' steels. The process of how copper, phosphorus and nickel contents affect the irradiation sensitivity of both types of steel seem to be similar. Some distinctions between the observed radiation effects is apparently caused by differences in the irradiation conditions and ratios of the contents of above mentioned elements in both types of steel. For 'Eastern' RPV steels the dependence of the recovery degree of irradiated steels due to postirradiation thermal annealing id obviously dependent on phosphorus contents and the influence of nickel contents on this process is detectable

  6. Bond characteristics of steel fiber and deformed reinforcing steel bar embedded in steel fiber reinforced self-compacting concrete (SFRSCC)

    Science.gov (United States)

    Aslani, Farhad; Nejadi, Shami

    2012-09-01

    Steel fiber reinforced self-compacting concrete (SFRSCC) is a relatively new composite material which congregates the benefits of the self-compacting concrete (SCC) technology with the profits derived from the fiber addition to a brittle cementitious matrix. Steel fibers improve many of the properties of SCC elements including tensile strength, ductility, toughness, energy absorption capacity, fracture toughness and cracking. Although the available research regarding the influence of steel fibers on the properties of SFRSCC is limited, this paper investigates the bond characteristics between steel fiber and SCC firstly. Based on the available experimental results, the current analytical steel fiber pullout model (Dubey 1999) is modified by considering the different SCC properties and different fiber types (smooth, hooked) and inclination. In order to take into account the effect of fiber inclination in the pullout model, apparent shear strengths ( τ ( app)) and slip coefficient ( β) are incorporated to express the variation of pullout peak load and the augmentation of peak slip as the inclined angle increases. These variables are expressed as functions of the inclined angle ( ϕ). Furthurmore, steel-concrete composite floors, reinforced concrete floors supported by columns or walls and floors on an elastic foundations belong to the category of structural elements in which the conventional steel reinforcement can be partially replaced by the use of steel fibers. When discussing deformation capacity of structural elements or civil engineering structures manufactured using SFRSCC, one must be able to describe thoroughly both the behavior of the concrete matrix reinforced with steel fibers and the interaction between this composite matrix and discrete steel reinforcement of the conventional type. However, even though the knowledge on bond behavior is essential for evaluating the overall behavior of structural components containing reinforcement and steel fibers

  7. Corrosion resistant steel

    International Nuclear Information System (INIS)

    Zubchenko, A.S.; Borisov, V.P.; Latyshev, V.B.

    1980-01-01

    Corrosion resistant steel for production of sheets and tubes containing C, Mn, Cr, Si, Fe is suggested. It is alloyed with vanadium and cerium for improving tensile properties and ductility. The steel can be melted by a conventional method in electric-arc or induction furnaces. The mentioned steel is intended to be used as a substitute for nickel-bearing austenitic steels

  8. ABOUT RATIONING MAXIMUM ALLOWABLE DEFECT DEPTH ON THE SURFACE OF STEEL BILLETS IN PRODUCTION OF HOT-ROLLED STEEL

    Directory of Open Access Journals (Sweden)

    PARUSOV E. V.

    2017-01-01

    Full Text Available Formulation of the problem. Significant influence on the quality of rolled steel have various defects on its surface, which in its turn inherited from surface defects of billet and possible damage to the surface of rolled steel in the rolling mill line. One of the criteria for assessing the quality indicators of rolled steel is rationing of surface defects [1; 2; 3; 6; 7]. Current status of the issue. Analyzing the different requirements of regulations to the surface quality of the rolled high-carbon steels, we can conclude that the maximum allowable depth of defects on the surface of billet should be in the range of 2.0...5.0 mm (depending on the section of the billet, method of its production and further the destination Purpose. Develop a methodology for calculating the maximum allowable depth of defects on the steel billet surface depending on the requirements placed on the surface quality of hot-rolled steel. Results. A simplified method of calculation, allowing at the rated depth of defects on the surface of the hot-rolled steel to make operatively calculation of the maximum allowable depth of surface defects of steel billets before heating the metal in the heat deformation was developed. The findings shows that the maximum allowable depth of surface defects is reduced with increasing diameter rolled steel, reducing the initial section steel billet and degrees of oxidation of the metal in the heating furnace.

  9. Heating temperature effect on ferritic grain size of rotor steel

    International Nuclear Information System (INIS)

    Cheremnykh, V.G.; Derevyankin, E.V.; Sakulin, A.A.

    1983-01-01

    The heating temperature effect on ferritic grain size of two steels 13Kh1M1FA and 25Kh1M1FA is evaluated. It is shown that exposure time increase at heating temperatures below 1000 deg C up to 10h changes but slightly the size of the Cr-Mo-V ferritic grain of rotor steel cooled with 25 deg C/h rate. Heating up to 1000 deg C and above leads to substantial ferritic grain growth. The kinetics of ferritic grain growth is determined by the behaviour of phases controlling the austenitic grain growth, such as carbonitrides VCsub(0.14)Nsub(0.78) in 13Kh1M1FA steel and VCsub(0.18)Nsub(0.72) in 25Kh1M1FA steel. Reduction of carbon and alloying elements content in steel composition observed at the liquation over rotor length leads to a certain decrease of ferritic grain resistance to super heating

  10. Performance of Retrofitted Self-Compacting Concrete-Filled Steel Tube Beams Using External Steel Plates

    Directory of Open Access Journals (Sweden)

    Ahmed A. M. AL-Shaar

    2018-01-01

    Full Text Available Self-compacting concrete-filled steel tube (SCCFST beams, similar to other structural members, necessitate retrofitting for many causes. However, research on SCCFST beams externally retrofitted by bolted steel plates has seldom been explored in the literature. This paper aims at experimentally investigating the retrofitting performance of square self-compacting concrete-filled steel tube (SCCFST beams using bolted steel plates with three different retrofitting schemes including varied configurations and two different steel plate lengths under flexure. A total of 18 specimens which consist of 12 retrofitted SCCFST beams, three unretrofitted (control SCCFST beams, and three hollow steel tubes were used. The flexural behaviour of the retrofitted SCCFST beams was examined regarding flexural strength, failure modes, and moment versus deflection curves, energy absorption, and ductility. Experimental results revealed that the implemented retrofitting schemes efficiently improve the moment carrying capacity and stiffness of the retrofitted SCCFST beams compared to the control beams. The increment in flexural strength ranged from 1% to 46%. Furthermore, the adopted retrofitting schemes were able to restore the energy absorption and ductility of the damaged beams in the range of 35% to 75% of the original beam ductility. Furthermore, a theoretical model was suggested to predict the moment capacity of the retrofitted SCCFST beams. The theoretical model results were in good agreement with the test results.

  11. Convergencia, divergencia y estratificación. Estudio comparativo de la dinámica de crecimiento de la manufactura en los municipios mexicanos y los condados estadunidenses

    Directory of Open Access Journals (Sweden)

    Rodolfo Cermeño

    2009-01-01

    Full Text Available En este artículo se analiza la dinámica del valor agregado manufacturero per capita como proxy del ingreso per capita de los municipios de México y condados de Estados Unidos. Específicamente, se busca determinar si existe convergencia (absoluta o condicional, divergencia o estratificación. Se utiliza un modelo de panel dinámico sin regresores exógenos y se considera el problema del sesgo en este contexto específico. En general se concluye que la dinámica del valor agregado per capita de los condados de Estados Unidos muestra convergencia condicional y poca dispersión de sus estados estacionarios. En cambio, en el caso de México se encuentra una dinámica congruente con crecimiento estratificado. El estudio también encuentra que el crecimiento de la manufactura en los condados de EEUU y los municipios de México diverge en el tiempo.

  12. Reduced-activation steels: present status and future development

    International Nuclear Information System (INIS)

    Klueh, R.L.

    2007-01-01

    Full text of publication follows: Reduced-activation steels for fusion reactor applications were developed in the 1980's to replace the commercial elevated- temperature steels first considered. In the United States, this involved replacing Sandvik HT9 and modified 9Cr-1Mo steels. Reduced-activation steels, which were developed for more rapid radioactivity decay following exposure in a fusion neutron environment, were patterned after the commercial steels they were to replace. The objective for the reduced-activation steels was that they have strengths (yield stress and ultimate tensile strength from room temperature to 600 deg. C) and impact toughness (measured in a Charpy test) comparable to or better than the steels they were replacing. That objective was achieved in reduced-activation steels developed in Japan, Europe, and the United States. Since the reduced-activation steels were developed in the 1980's, reactor designers have been interested designs for increased efficiency of future fusion plants. This means reactors will need to operate at higher temperatures-above 550 deg. C, which is the upper-temperature limit for the reduced-activation steels. Although the tensile and impact toughness of the reduced-activation steels exceed those of the commercial steels they were patterned after, their creep-rupture properties are inferior to some of the commercial steels they replaced. furthermore, they are much inferior to commercial steels that have been developed since the 1980's. Reasons for why the creep-rupture properties for the new commercial ferritic/martensitic steels are superior to the earlier commercial steels and the reduced-activation steels were examined. The reasons involve compositional changes that were made in the earlier commercial steels to give the new commercial steels their superior properties. Computational thermodynamics calculations were carried out to compare the expected equilibrium phases. It appears that similar changes in composition

  13. Austenitic stainless steels with cryogenic resistance

    International Nuclear Information System (INIS)

    Tarata, Daniela Florentina

    1999-01-01

    The most used austenitic stainless steels are alloyed with chromium and nickel and have a reduced carbon content, usually lower than 0.1 % what ensures corresponding properties for processing by plastic deformation at welding, corrosion resistance in aggressive environment and toughness at low temperatures. Steels of this kind alloyed with manganese are also used to reduce the nickel content. By alloying with manganese which is a gammageneous element one ensures the stability of austenites. Being cheaper these steels may be used extensively for components and equipment used in cryogenics field. The best results were obtained with steels of second group, AMnNi, in which the designed chemical composition was achieved, i.e. the partial replacement of nickel by manganese ensured the toughness at cryogenic temperatures. If these steels are supplementary alloyed, their strength properties may increase to the detriment of plasticity and toughness, although the cryogenic character is preserved

  14. Inhibition of HIV-1 Integrase gene expression by 10-23 DNAzyme

    Indian Academy of Sciences (India)

    We have designed three novel DNAzymes, DIN54, DIN116, and DIN152, against HIV-1 Integrase gene using Mfold software and evaluated them for target site cleavage activity on the in vitro transcribed mRNA. All DNAzymes were tested for its inhibition of expression of HIV Integrase protein in the transiently transfected cell ...

  15. Damascus steels: history, processing, properties and carbon dating

    International Nuclear Information System (INIS)

    Wadsworth, J.

    2007-01-01

    In the mid-1970s, a class of steels containing high levels of carbon (∼ 1-2 wt% C) was developed for superplastic characteristics - that is, the ability to plastically deform to an extraordinary degree in tension at intermediate temperatures. Because these steels also had excellent room temperature properties, they were developed for their commercial potential. In the late 1970s, we became aware of the striking compositional similarities between these modern steels and the ancient steels of Damascus. This observation led us to revisit the history and metallurgy of Damascus steels and related steels. The legends and origins of Damascus steel date back to the time of Alexander the Great (323 BC) and the medieval Crusades (11th and 12th century AD), and this material has also been the subject of scrutiny by famous scientist in Europe, including Michael Faraday. Modern attempts to reproduce the legendary surface patterns which famously characterized Damascus steels are described. The extend to which the characteristics of Damascus steels are unusual is discussed. Finally, a program on radiocarbon dating was initiated to directly determine the age of about 50 ancient steels, including a Damascus knife, and the results are summarized. (author)

  16. Thermal embrittlement of reactor vessel steels

    International Nuclear Information System (INIS)

    Corwin, W.R.; Nanstad, R.K.; Alexander, D.J.; Stoller, R.E.; Wang, J.A.; Odette, G.R.

    1995-01-01

    As a result of observations of possible thermal embrittlement from recent studies with welds removed from retired steam generators of the Palisades Nuclear Plant (PNP), an assessment was made of thermal aging of reactor pressure vessel (RPV) steels under nominal reactor operating conditions. Discussions are presented on (1) data from the literature regarding relatively low-temperature thermal embrittlement of RPV steels; (2)relevant data from the US power reactor-embrittlement data base (PR-EDB); and (3)potential mechanisms of thermal embrittlement in low-alloy steels

  17. Financial Management: Emergency Steel Loan Guarantee Program

    National Research Council Canada - National Science Library

    2001-01-01

    In a February 1, 2001 letter, you expressed concerns about repayments of federally guaranteed loans by borrowers under the Emergency Steel Loan Guarantee Program and the effect of the program on the U.S. steel industry...

  18. Some elevated temperature tensile and strain-controlled fatigue properties for a 9%Cr1Mo steel heat treated to simulate thick section material

    International Nuclear Information System (INIS)

    Sanderson, S.J.; Jacques, S.

    Current interest has been expressed in the usage of thick section 9%Cr1%Mo steel, particularly for UK Commercial Demonstration Fast Reactor (CDFR) steam generator tubeplates. This paper presents the results of some preliminary mechanical property test work on a single cast of the steel, heat treated to simulate heavy ruling sections encompassing thicknesses likely to be met in the CDFR context. The microstructures of the simulated thick section material were found to remain predominantly as tempered martensite even at the slowest transformation cooling rates used (50 deg. C/h). The effect of microstructure is reflected in the elevated temperature proof stress, tensile strength and strain-controlled fatigue endurance which were found to be comparable with the properties established for thin section normalised and tempered 9%Cr1%Mo steel. These results are extremely encouraging and, taken in conjunction with the results from other simulation work on this material, further demonstrate the potential of thick section 9%Cr1%Mo steel. (author)

  19. [Relationship between shift work and overweight/obesity in male steel workers].

    Science.gov (United States)

    Xiao, M Y; Wang, Z Y; Fan, H M; Che, C L; Lu, Y; Cong, L X; Gao, X J; Liu, Y J; Yuan, J X; Li, X M; Hu, B; Chen, Y P

    2016-11-10

    Objective: To investigate the relationship between shift work and overweight/obesity in male steel workers. Methods: A questionnaire survey was conducted among the male steel workers selected during health examination in Tangshan Steel Company from March 2015 to March 2016. The relationship between shift work and overweight/obesity in the male steel workers were analyzed by using logistic regression model and restricted cubic splinemodel. Results: A total of 7 262 male steel workers were surveyed, the overall prevalence of overweight/obesitywas 64.5% (4 686/7 262), the overweight rate was 34.3% and the obesity rate was 30.2%, respectively. After adjusting for age, educational level and average family income level per month by multivariable logistic regression analysis, shift work was associated with overweight/obesity and obesity in the male steel workers. The OR was 1.19(95% CI : 1.05-1.35) and 1.15(95% CI : 1.00-1.32). Restricted cubic spline model analysis showed that the relationship between shift work years and overweight/obesity in the male steel workers was a nonlinear dose response one (nonlinear test χ 2 =7.43, P shift work years and obesity in the male steel workers was a nonlinear dose response one (nonlinear test χ 2 =10.48, P Shift work was associated with overweight and obesity in the male steel workers, and shift work years and overweight/obesity had a nonlinear relationship.

  20. Leaching of heavy metals from steelmaking slags

    International Nuclear Information System (INIS)

    Gomez, J. F. P.; Pino, C. G.

    2006-01-01

    Leaching tests with EAF and Ladle slags were performed, using a flow through tests and the standard batch test DIN 38414-S4. The previous method was used to simulate the leaching behaviour of steel slags under landfill. the chemical analysis of the leachates during this period shows, in general, for both types of slag, and increase of heavy metal releases with ageing. Standard test method DIN 38414-S4 was used to evaluate leachability of heavy metals by water in unprocessed slags. After more than one year of trials, slang samples submitted to these trials presented very low total leaching levels. The most extracted elements are calcium and magnesium. Nevertheless, in flow-though test, calcium and magnesium leached from solid slags are below 0.5% and all other metals below 0.1%. Leachates obtained with DIN 38414-S4 present, as expected, higher leaching values; however, these are inferior to 5% (Ca) and 1% (other elements). (Author) 12 refs

  1. Prediction and Monitoring Systems of Creep-Fracture Behavior of 9Cr-1Mo Steels for Reactor Pressure Vessels

    International Nuclear Information System (INIS)

    Potirniche, Gabriel; Barlow, Fred D.; Charit, Indrajit; Rink, Karl

    2013-01-01

    A recent workshop on next-generation nuclear plant (NGNP) topics underscored the need for research studies on the creep fracture behavior of two materials under consideration for reactor pressure vessel (RPV) applications: 9Cr-1Mo and SA-5XX steels. This research project will provide a fundamental understanding of creep fracture behavior of modified 9Cr-1Mo steel welds for through modeling and experimentation and will recommend a design for an RPV structural health monitoring system. Following are the specific objectives of this research project: Characterize metallurgical degradation in welded modified 9Cr-1Mo steel resulting from aging processes and creep service conditions; Perform creep tests and characterize the mechanisms of creep fracture process; Quantify how the microstructure degradation controls the creep strength of welded steel specimens; Perform finite element (FE) simulations using polycrystal plasticity to understand how grain texture affects the creep fracture properties of welds; Develop a microstructure-based creep fracture model to estimate RPVs service life; Manufacture small, prototypic, cylindrical pressure vessels, subject them to degradation by aging, and measure their leak rates; Simulate damage evolution in creep specimens by FE analyses; Develop a model that correlates gas leak rates from welded pressure vessels with the amount of microstructural damage; Perform large-scale FE simulations with a realistic microstructure to evaluate RPV performance at elevated temperatures and creep strength; Develop a fracture model for the structural integrity of RPVs subjected to creep loads; and Develop a plan for a non-destructive structural health monitoring technique and damage detection device for RPVs.

  2. Prediction and Monitoring Systems of Creep-Fracture Behavior of 9Cr-1Mo Steels for Teactor Pressure Vessels

    Energy Technology Data Exchange (ETDEWEB)

    Potirniche, Gabriel [Univ. of Idaho, Moscow, ID (United States); Barlow, Fred D. [Univ. of Idaho, Moscow, ID (United States); Charit, Indrajit [Univ. of Idaho, Moscow, ID (United States); Rink, Karl [Univ. of Idaho, Moscow, ID (United States)

    2013-11-26

    A recent workshop on next-generation nuclear plant (NGNP) topics underscored the need for research studies on the creep fracture behavior of two materials under consideration for reactor pressure vessel (RPV) applications: 9Cr-1Mo and SA-5XX steels. This research project will provide a fundamental understanding of creep fracture behavior of modified 9Cr-1Mo steel welds for through modeling and experimentation and will recommend a design for an RPV structural health monitoring system. Following are the specific objectives of this research project: Characterize metallurgical degradation in welded modified 9Cr-1Mo steel resulting from aging processes and creep service conditions; Perform creep tests and characterize the mechanisms of creep fracture process; Quantify how the microstructure degradation controls the creep strength of welded steel specimens; Perform finite element (FE) simulations using polycrystal plasticity to understand how grain texture affects the creep fracture properties of welds; Develop a microstructure-based creep fracture model to estimate RPVs service life; Manufacture small, prototypic, cylindrical pressure vessels, subject them to degradation by aging, and measure their leak rates; Simulate damage evolution in creep specimens by FE analyses; Develop a model that correlates gas leak rates from welded pressure vessels with the amount of microstructural damage; Perform large-scale FE simulations with a realistic microstructure to evaluate RPV performance at elevated temperatures and creep strength; Develop a fracture model for the structural integrity of RPVs subjected to creep loads; and Develop a plan for a non-destructive structural health monitoring technique and damage detection device for RPVs.

  3. Obtención de Modelos Borrosos Interpretables de Procesos Dinámicos

    Directory of Open Access Journals (Sweden)

    Juan Contreras Montes

    2008-07-01

    Full Text Available Resumen: En este artículo se presenta una novedosa metodología para la construcción de modelos borrosos lingüísticamente interpretables, a partir de datos de entrada y salida, de procesos dinámicos. Se describe una sencilla técnica de agrupamiento para construcción de las reglas borrosas, así como el empleo de mínimos cuadrados para ajuste de consecuentes. Para garantizar la interpretabilidad del modelo borroso la partición de los antecedentes emplea conjuntos triangulares con interpolación de 0.5. El aspecto más promisorio en nuestra propuesta consiste en alcanzar una buena precisión sin sacrificar la interpretabilidad del sistema borroso ni recurrir a otras técnicas de inteligencia artificial. Se presentan aplicaciones a problemas o conjuntos de datos ampliamente conocidos (benchmark classic como la cámara de gas de Box-Jenkins, la serie caótica de Mackey Glass y la dinámica de cabeceo de un helicóptero a escala, y se comparan los resultados con aquellos obtenidos por otros autores que emplean técnicas diferentes. Palabras clave: identificación, agrupamiento, mínimos cuadrados, modelo borroso, interpretabilidad

  4. Programação dinâmica aplicada a finanças

    Directory of Open Access Journals (Sweden)

    Tara Keshar Nanda Baídya

    1997-12-01

    Full Text Available Este artigo mostra a aplicação da programação dinâmica estocástica e o seu uso em Finanças. Um dos objetivos mais usuais da teoria financeira é determinar a trajetória ou caminho ótimo para determinada variável. Brennan e Schwartz (1985 analisaram economicamente o investimento na exploração de um recurso mineral. Determinaram o valor do projeto e o instante ótimo de realizar o investimento. Para tal, usaram os conceitos da teoria das opções e técnicas de avaliação por arbitragem. Este artigo obtém o mesmo modelo usando a programação dinâmica e os conceitos de finanças em tempo contínuoThis paper shows the dynamic programming approach related to Finance Theory. We exhibit how to construct the optimal path, one of the most important aims in the Finance. Brennan and Shwartz (1985 derived their model to evaluate a project of mining using option pricing theory and arbitrage approach. This is an use of option theory to evaluate a real project. Here we obtain the same model as an example, using stochastic dynamic programming

  5. Novo desenvolvimentismo e dinâmica urbano-regional no Brasil (2004-2012

    Directory of Open Access Journals (Sweden)

    Hipólita Siqueira

    2015-01-01

    Full Text Available As mudanças no contexto nacional e internacional impuseram novas questões ao debate sobre a dinâmica urbano-regional brasileira. Dentre elas, o aprofundamento da inserção internacional do País, tendo como base seu potencial de recursos naturais e sua articulação com o "efeito-China" na reconfiguração das relações internacionais, e o processo de desindustrialização, decorrente da especialização produtiva regressiva e da apreciação da taxa de câmbio. O objetivo deste artigo é examinar as lin-has gerais da dinâmica urbano-regional no âmbito das transformações na economia e sociedade brasileiras desde os anos 1980, especialmente no período pós-2004, em que ocorre uma retomada do crescimento econômico e dos gastos estatais. Entende-se que tal análise enfrenta desafios teórico-metodológicos importantes, sendo necessário o resgate de referenciais analíticos, como o da divisão espacial do trabalho para o entendimento das desigualdades regionais, e a (reformulação da questão regional brasileira.

  6. Standard test method for electrochemical critical pitting temperature testing of stainless steels

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    1999-01-01

    1.1 This test method covers a procedure for the evaluation of the resistance of stainless steel and related alloys to pitting corrosion based on the concept of the determination of a potential independent critical pitting temperature (CPT). 1.2 This test methods applies to wrought and cast products including but not restricted to plate, sheet, tubing, bar, forgings, and welds, (see Note 1). Note 1—Examples of CPT measurements on sheet, plate, tubing, and welded specimens for various stainless steels can be found in Ref (1). See the research reports (Section 14). 1.3 The standard parameters recommended in this test method are suitable for characterizing the CPT of austenitic stainless steels and other related alloys with a corrosion resistance ranging from that corresponding to solution annealed UNS S31600 (Type 316 stainless steel) to solution annealed UNS S31254 (6 % Mo stainless steel). 1.4 This test method may be extended to stainless steels and other alloys related to stainless steel that have a CPT...

  7. Standardization work by ASTM and DIN concerning test methods for metallic materials - comparative assessment with regard for practice

    International Nuclear Information System (INIS)

    Gerischer, K.

    1986-01-01

    The article explains the significant role of ASTM and marks out basic elements of the specification system of ASTM standards. Usefulness in practice is taken as the main criterion for the subsequent comparison of ASTM or DIN activities and procedures, and results, for standardization in the field of test methods for metallic materials. The main differences are shown to exist with regard to tropicality of test standards, presentation of useful information and background knowledge, and importance attached to formal questions. ASTM standardization work is shown to be more up-to-date, contain more information, and to be less concerned with formal matters. A closer cooperation between ASTM and DIN is strongly recommended. (orig.) [de

  8. Gaisma un krāsa sabiedriskās ēdināšanas telpās

    OpenAIRE

    Cvetkova, Diāna

    2015-01-01

    Diplomdarbā „Gaisma un krāsa sabiedriskās ēdināšanas telpās” autore analizē informāciju par apgaismojuma un krāsas lomām sabiedriskās ēdināšanas telpās. Labākam priekšstatam autore detāli apraksta to, kā apgaismojums un krāsa var izmainīt telpu un ietekmēt cilvēka psiholoģisko stāvokli un noskaņojumu, kā arī, kā noteiktas krasas apgaismojums var izmainīt ēdiena krāsu, tādējādi ietekmējot mūsu ēstgribu. Empiriskā daļā autore analizē interjerus kafejnīcās unrestorānos, kas atrodas Rīgas pi...

  9. The steel scrap age.

    Science.gov (United States)

    Pauliuk, Stefan; Milford, Rachel L; Müller, Daniel B; Allwood, Julian M

    2013-04-02

    Steel production accounts for 25% of industrial carbon emissions. Long-term forecasts of steel demand and scrap supply are needed to develop strategies for how the steel industry could respond to industrialization and urbanization in the developing world while simultaneously reducing its environmental impact, and in particular, its carbon footprint. We developed a dynamic stock model to estimate future final demand for steel and the available scrap for 10 world regions. Based on evidence from developed countries, we assumed that per capita in-use stocks will saturate eventually. We determined the response of the entire steel cycle to stock saturation, in particular the future split between primary and secondary steel production. During the 21st century, steel demand may peak in the developed world, China, the Middle East, Latin America, and India. As China completes its industrialization, global primary steel production may peak between 2020 and 2030 and decline thereafter. We developed a capacity model to show how extensive trade of finished steel could prolong the lifetime of the Chinese steelmaking assets. Secondary steel production will more than double by 2050, and it may surpass primary production between 2050 and 2060: the late 21st century can become the steel scrap age.

  10. Preparation and characterization of 304 stainless steel/Q235 carbon steel composite material

    Directory of Open Access Journals (Sweden)

    Wenning Shen

    Full Text Available The composite material of 304 stainless steel reinforced Q235 carbon steel has been prepared by modified hot-rolling process. The resulted material was characterized by scanning electron microscope, three-electrode method, fault current impact method, electrochemical potentiodynamic polarization curve measurement and electrochemical impedance spectroscopy. The results showed that metallurgical bond between the stainless steel layer and carbon steel substrate has been formed. The composite material exhibited good electrical conductivity and thermal stability. The average grounding resistance of the composite material was about 13/20 of dip galvanized steel. There has no surface crack and bubbling formed after fault current impact. The composite material led to a significant decrease in the corrosion current density in soil solution, compared with that of hot dip galvanized steel and bare carbon steel. On the basis polarization curve and EIS analyses, it can be concluded that the composite material showed improved anti-corrosion property than hot-dip galvanized steel. Keywords: Stainless steel, Carbon steel, Anti-corrosion, Conductivity, Electrochemical, EIS

  11. Mapping Two-Dimensional Deformation Field Time-Series of Large Slope by Coupling DInSAR-SBAS with MAI-SBAS

    Directory of Open Access Journals (Sweden)

    Liming He

    2015-09-01

    Full Text Available Mapping deformation field time-series, including vertical and horizontal motions, is vital for landslide monitoring and slope safety assessment. However, the conventional differential synthetic aperture radar interferometry (DInSAR technique can only detect the displacement component in the satellite-to-ground direction, i.e., line-of-sight (LOS direction displacement. To overcome this constraint, a new method was developed to obtain the displacement field time series of a slope by coupling DInSAR based small baseline subset approach (DInSAR-SBAS with multiple-aperture InSAR (MAI based small baseline subset approach (MAI-SBAS. This novel method has been applied to a set of 11 observations from the phased array type L-band synthetic aperture radar (PALSAR sensor onboard the advanced land observing satellite (ALOS, spanning from 2007 to 2011, of two large-scale north–south slopes of the largest Asian open-pit mine in the Northeast of China. The retrieved displacement time series showed that the proposed method can detect and measure the large displacements that occurred along the north–south direction, and the gradually changing two-dimensional displacement fields. Moreover, we verified this new method by comparing the displacement results to global positioning system (GPS measurements.

  12. Chemical reduction of rust on 2 1/4 Cr-1 Mo steel surface in sodium

    International Nuclear Information System (INIS)

    Yokota, N.; Shimoyashiki, S.

    1986-01-01

    Low-alloy Fe-2 1/4 Cr-1 Mo ferritic steel has been favored for the tube material of steam generators in fast breeder reactors (FBRs). However, this material rusts easily due to moisture condensation on its surface when left in air. Therefore, measures to prevent tube materials from rusting have been taken during manufacturing of the steam generators. When rust is present on tube surfaces, its oxygen and iron dissolve into liquid sodium. When the concentration of these impurities in the sodium increases rapidly, the cold traps can become choked locally and lose their removal ability. This work has been done, therefore, to clarify reduction processes of rust in sodium and to select optimum operating temperatures of steam generators in the initial operation

  13. [Prevalence and influence factors of hypertension among the workers exposed to noise in steel making and steel rolling workshop of an iron and steel plant].

    Science.gov (United States)

    Li, Yanhong; Chen, Guoshun; Yu, Shanfa

    2015-05-01

    To investigate the prevalence and influence factors of hypertension among the workers exposed to noise in steel making and steel rolling workshop of an iron and steel plant. Using cluster sampling method, 3 150 workers exposed to noise participated in this study. According to do questionnaire survey and blood pressure measurement, 2 924 workers were tested, among which 1 313 workers were from steel making workshop and 1 611 workers were from steel rolling workshop. The relationships between different demographic characteristics, different habits, and different cumulative noise exposures of workers exposed to noise and hypertension were analyzed. For the hypertension prevalence rate, the total prevalence rate was 27.43% (802/2 924), the male was higher than the female (29.88 % (753/2 520) vs 12.13% (49/404), χ² = 55.13, P married ones were higher than the unmarried (29.84% (718/2 406) vs 16.22% (84/518), χ² = 39.76, P vs 24.61% (364/1 479), χ² = 11.93, P = 0.001), drinking ones were higher than the no drinking (31.53% (541/1 716) vs 21.61% (261/1 208), χ² = 35.05, P < 0.001). The hypertension prevalence rates among the subjects with education background in junior high school and below, high school (secondary) and university and above were separately 44.96%(125/278), 29.95%(455/1 519) and 19.70%(222/1 127) (χ² = 81.65, P < 0.001), among cumulative exposure groups 77-89, 90-94, 95-99, 100-104 and 105-113 were separately 8.43% (14/166), 14.48% (53/366), 24.28% (297/1 223), 36.65% (335/914) and 40.39%(103/255) (χ² = 127.58, P < 0.001). Multivariate logistic regression analysis showed that workers who exposed to cumulative noise in 95-99, 100-104 and 105-113 dB(A) ·year had the higher risk of hypertension, the OR (95%CI) were 1.84 (95% CI: 1.35-2.51), 1.74 (95% CI: 1.24-2.45) and 1.68 (95% CI: 1.09-2.58). Drinking (OR = 1.60, 95% CI: 1.32-1.95) and BMI ≥ 24.0 kg/m² (OR = 1.26, 95% CI: 1.22-1.30) were the risk factors for hypertension as well. Cumulative

  14. Dinâmica familiar: percepção de famílias de sobreviventes de câncer de mama Dinámica familiar: percepción de familias de sobrevivientes de cancer de mama Family dynamics: perceptions of breast cancer survivor's families

    Directory of Open Access Journals (Sweden)

    Raquel Gabrielli Biffi

    2009-03-01

    Full Text Available O estudo teve como objetivo identificar as percepções de familiares sobre a dinâmica de suas famílias após o câncer de mama em um dos seus membros. Estudo de abordagem qualitativa que tomou como referencial teórico o modelo de funcionamento familiar saudável proposto por Barnhill (1979. Participaram 23 familiares constituintes de 10 famílias. Os dados foram coletados, no período de maio a junho de 2002, por meio de entrevistas, e submetidos à análise de conteúdo. Os resultados revelaram aspectos positivos na dinâmica das famílias. A percepção dos processos de identidade, através da individuação e mutualidade, favoreceram a compreensão da dinâmica familiar. Os achados mostraram que o câncer de mama tem a capacidade de provocar alterações na família, e esta se utilizou dos potenciais de cada membro em particular na busca da estabilidade familiar.El estudio objetiva identificar las percepciones de familiares sobre la dinámica de sus familias, con cáncer de mama en uno de sus miembros. Estudio de abordaje cualitativo que tomó como referencial teórico el modelo de funcionamiento familiar saludable de Barnhill (1979. Participaron 23 familiares constituyentes de 10 familias. Los datos fueron obtenidos mediante entrevistas y sometidos a análisis de contenido. Los resultados revelaron aspectos positivos en la dinámica de las familias. La percepción de los procesos de identidad, a través de la individualización y mutualidad, favoreció la comprensión de la dinámica familiar. Según los resultados, el cáncer de mama tiene la capacidad de provocar alteraciones en la familia; por otro lado, éstas se utilizaron de los potenciales de cada miembro, en particular, en la búsqueda de la estabilidad familiar.The aim of this study was to identify the family members´ perceptions of their family dynamics, after breast cancer in one of its members. The study used a qualitative approach based on the theoretical model of healthy

  15. Prospectiva de la cadena Productiva de mango bajo el enfoque dinámico

    Directory of Open Access Journals (Sweden)

    Juan Pablo Tribín-Rivera

    2014-01-01

    Full Text Available El propósito del presente documento de investigación, es relacionar los resultados del análisis prospectivo de la cadena productiva de mango en la Provincia del Tequendama – Cundinamarca por medio de dinámica de sistemas, con el fin de compararla desde distintos escenarios; mercado interno frente al mercado externo, y así poder determinar el escenario prospectivo más conveniente para los productores. De igual forma se proponen políticas que mejoren las condiciones de los productores de la región y se relaciona el modelo de simulación por dinámica de sistemas, que puede ser utilizado en diferentes cadenas productivas. La construcción del modelo de simulación se desarrolló con base en las experiencias adquiridas por medio de visitas de campo, recolección de información primaria y secundaria, y la colaboración de expertos que participan, directa o indirectamente, en dicha cadena productiva, enmarcadas bajo el proyecto de investigación titulado “Mercado prospectivo del mango: Comparativo entre el mercado interno y el mercado externo para la Provincia del Tequendama – Cundinamarca”

  16. MECANISMUL DE PROTEOLIZĂ A FICOCIANINEI, PROTEINEI BIOACTIVE DIN SPIRULINĂ SUB ACŢIUNEA PAPAINEI

    Directory of Open Access Journals (Sweden)

    Angela RUDAKOVA

    2016-02-01

    Full Text Available Elaborarea unor procedee de obţinere a peptidelor bioactive din ficocianină prin intermediul hidrolizei proteolitice prezintă un interes sporit pentru cercetători în contextul utilizării acestora în calitate de remedii anticancer şi pentru alte proprietăţi terapeutice. Peptidele derivate din ficocianină ar putea manifesta proprietăţi terapeutice mult mai pronunţate comparativ cu ficocianina. În prezenta lucrare sunt studiate dinamica proteolizei ficocianinei cu papaina şi mecanismul de hidroliză a acestei proteine.Mechanism of proteolysis of C-phycocyanin, bioactive protein from Spirulina, under the action of papainThe elaboration of the procedures of obtaining of bioactive peptides derived from phycocyanin, as a result of it proteolytic hydrolysis presents great interest for researchers in the terms of theirs use as anti-cancer drugs and for other therapeutic properties. It can be assumed that peptides derived from phycocyanin could manifest more pronounced therapeutic effects compared to phycocyanin. Dynamics of phycocyanin proteolisis by papain, as well as mechanism of phycocyanin hydrolysis were studied in the present work. 

  17. The microwave assisted synthesis of 1-alkyl-3-methylimidazolium bromide as potential corrosion inhibitor toward carbon steel in 1 M HCl solution saturated with carbon dioxide

    Energy Technology Data Exchange (ETDEWEB)

    Pasasa, Norman Vincent A., E-mail: npasasa@gmail.com; Bundjali, Bunbun; Wahyuningrum, Deana [Department of Chemistry, Faculty of Mathematics and Natural Sciences, Institut Teknologi Bandung, Jalan Ganesha No. 10 Bandung, Jawa Barat (Indonesia)

    2015-09-30

    Injection of corrosion inhibitor into the fluid current of oil and gas pipelines is an effective way to mitigate corrosion rate on the inner-surface parts of pipelines, especially carbon steel pipelines. In this research, two alkylimidazolium ionic liquids, 1-decyl-3-methylimidazolium bromide (IL1) and 1-dodecyl-3-methylimidazolium bromide (IL2) have been synthesized and studied as a potential corrosion inhibitor towards carbon steel in 1 M HCl solution saturated with carbon dioxide. IL1 and IL2 were synthesized using microwave assisted organic synthesis (MAOS) method. Mass Spectrometry analysis of IL1 and IL2 showed molecular mass [M-H+] peak at 223.2166 and 251.2484, respectively. The FTIR,{sup 1}H-NMR and {sup 13}C-NMR spectra confirmed that IL1 and IL2 were successfully synthesized. Corrosion inhibition activity of IL1 and IL2 were determined using weight loss method. The results showed that IL1 and IL2 have the potential as good corrosion inhibitors with corrosion inhibition efficiency of IL1 and IL2 are 96.00% at 100 ppm (343 K) and 95.60% at 50 ppm (343 K), respectively. The increase in the concentration of IL1 and IL2 tends to improve their corrosion inhibition activities. Analysis of the data obtained from the weight loss method shows that the adsorption of IL1 and IL2 on carbon steel is classified into chemisorption which obeys Langmuir’s adsorption isotherm.

  18. Compatibility of graphite with a martensitic-ferritic steel, an austenitic stainless steel and a Ni-base alloy up to 1250 C

    International Nuclear Information System (INIS)

    Hofmann, P.

    1994-08-01

    To study the chemical interactions between graphite and a martensitic-ferritic steel (1.4914), an austenitic stainless steel (1.4919; AISI 316), and a Ni-base alloy (Hastelloy X) isothermal reaction experiments were performed in the temperature range between 900 and 1250 C. At higher temperatures a rapid and complete liquefaction of the components occurred as a result of eutectic interactions. The chemical interactions are diffusion-controlled processes and can be described by parabolic rate laws. The reaction behavior of the two steels is very similar. The chemical interactions of the steels with graphite are much faster above 1100 C than those for the Ni-base alloy. Below 1000 C the effect is opposite. (orig.) [de

  19. La dinámica pendular de la regionalización de la universidad en Argentina

    Directory of Open Access Journals (Sweden)

    Claudio Antonio Rama Vitale

    2014-11-01

    Full Text Available El artículo analiza la dinámica de construcción del sistema de educación superior pública en Argentina atendiendo a las dimensiones de su regionalización y explorando  las tensiones regionales alrededor de sus construcción. Visualiza bajos niveles de diferenciación institucional y de competencia institucional, pero indica las complejidades de esa diferenciación regional, el carácter no resuelto políticamente de tales procesos, y como su dinámica ha estado asociada a procesos político ideológicos. La regionalización de la educación superior muestra múltiples expresiones, pero donde la dominante ha sido la tensión entre la construcción de  espacios de poder y de desarrollo académico a escala local frente al objetivo desde los ámbitos nacionales de regular nacionalmente la educación superior.  

  20. Capacidades dinámicas que influyen en la operación de la Red de Turismo de La Candelaria

    OpenAIRE

    Gutiérrez Rodríguez, Alejandro Javier

    2013-01-01

    El desarrollo de la presente investigación, centra su atención en las capacidades dinámicas que influyen en la operación de la Red de Turismo de La Candelaria de Bogotá. Para este fin, se realizó una encuesta a 100 directivos o dueños de las empresas que conforman dicha red, y que es una muestra significativa para los propósitos de la investigación, puesto que permite describir a nivel de la empresa y a nivel de la red, la influencia de las capacidades dinámicas de absorción, adaptación e inn...

  1. Nondestructive testing for microstructural characterization in 9Cr-1Mo ferritic steel towards assessment of fabrication quality and in-service degradation

    Energy Technology Data Exchange (ETDEWEB)

    Jayakumar, T.; Rao, K.B.S.; Raj, Baldev [Indira Gandhi Centre for Atomic Research, Kalpakkam (India)

    1999-07-01

    The paper discusses the usefulness of non destructive testing for microstructural characterization in 9Cr-1Mo ferritic steel. Ultrasonic velocity and attenuation measurements and spectral analysis have been used in a complementary way for characterizing Ac{sub 1} and Ac{sub 3} temperatures, amount of martensite and ferrite, dissolution of V{sub 4}C{sub 3} and NbC and formation of {delta}-ferrite. The microstructural degradation occurring due to thermal ageing and creep has also been studied by ultrasonic velocity measurements. Magnetic Barkhausen noise technique has been used for estimating the extent of various regions in heat affected zone (HAZ) of 9Cr-1Mo ferritic steel weldment. The same technique has been used for the assessment of low cycle fatigue damage in 9Cr-1Mo steel. The study establishes that non destructive methods can be used for the assessment of fabrication quality and in service degradation of the components. (author)

  2. Plasticity of low carbon stainless steels

    International Nuclear Information System (INIS)

    Bulat, S.I.; Fel'dgandler, Eh.G.; Kareva, E.N.

    1975-01-01

    In the temperature range 800-1200 0 C and with strain rates of from 10 -3 to 3 s -1 , austenitic (000Kh18N12) and austenitic-ferrite (000Kh26N6) very low carbon stainless steels containing 0.02-0.03% C exhibit no higher resilience than corresponding ordinary steels containing 0.10-0.12% C. However, the plasticity of such steels (particularly two-phase steels) at 900-1100 0 C is appreciably inferior owing to the development of intergranular brittle fracture. Pressure treatment preceded by partial cooling of the surface to 850 0 C yields rolled and forged products with acceptable indices but is inconvenient technically. At the Zlatoustovsk and Ashin metallurgical plants successful tests have been performed involving the forging and rolling of such steels heated to 1280-1300 0 C without partial cooling; it was necessary to improve the killing conditions, correct the chemical composition (increasing the proportion of ferrite) and take measures against heat loss. (author)

  3. A comparison of low-chromium and high-chromium reduced-activation steels for fusion applications

    International Nuclear Information System (INIS)

    Klueh, R.L.; Maziasz, P.J.; Alexander, D.J.

    1996-01-01

    Ferritic steels have been considered candidate structural materials for first wall and blanket structures for fusion power plants since the late 1970s. The first steels considered in the United States were the conventional Cr-Mo steels Sandvik HT9 (nominally 12Cr-1Mo-0.25V-0.5W-0.5Ni-0.2C, here designated l2Cr-1MoVW), modified 9Cr-1Mo steel (9Cr-1Mo-0.2V-0.06Nb-0. IC, designated 9Cr-1MoVNb) and, to a lesser extent, 2 1/4Cr-1Mo steel (2.25Cr-Mo-0.1C). All compositions are in wt. %. The normalized-and-tempered 9 and 12Cr steels had a tempered martensite microstructure, and the normalized-and-tempered 2 1/4 Cr steel had a tempered bainite microstructure. This report describes chromium steels tested in normalized and tempered conditions. Miniature tensile and Charpy specimens were tested

  4. O ciclo do café durante a República Velha: uma análise com a abordagem de dinâmica de sistemas

    Directory of Open Access Journals (Sweden)

    Thiago Caliari

    2011-05-01

    Full Text Available O objetivo deste trabalho é fazer uma análise sistêmica da dinâmica da produção cafeeira no Brasil com foco no período 1900-1930. A motivação para abordar a questão sob a ótica da dinâmica de sistemas (system dynamics é que essa metodologia é especialmente adequada para modelar processos sujeitos à complexidade dinâmica, como os ciclos de produção de commodities. Mostrar-se-á que modelar e simular a dinâmica da produção de café no Brasil com essa metodologia permite, em primeiro lugar, realizar experimentos contra-factuais que possibilitam avaliar quantitativamente o efeito de políticas de defesa de preços, como as políticas de valorização, complementando a já extensa e rica literatura sobre o assunto. Em segundo lugar, será sugerido que abordar a questão sob esta ótica ajuda a extrair insights de política não apenas para o café como para outras commodities, das quais o Brasil ainda depende de forma importante para manter o equilíbrio em suas contas externas.

  5. Heat treatment effects on impact toughness of 9Cr-1MoVNb and 12Cr-1MoVW steels irradiated to 100 dpa

    Energy Technology Data Exchange (ETDEWEB)

    Klueh, R.L.; Alexander, D.J. [Oak Ridge National Lab., TN (United States)

    1997-08-01

    Plates of 9Cr-1MoVNb and 12Cr-1MoVW steels were given four different heat treatments: two normalizing treatments were used and for each normalizing treatment two tempers were used. Miniature Charpy specimens from each heat treatment were irradiated to {approx}19.5 dpa at 365{degrees}C and to {approx}100 dpa at 420{degrees}C in the Fast Flux Test Facility (FFTF). In previous work, the same materials were irradiated to 4-5 dpa at 365{degrees}C and 35-36 dpa at 420{degrees}C in FFTF. The tests indicated that prior austenite grain size, which was varied by the different normalizing treatments, had a significant effect on impact behavior of the 9Cr-1MoVNb but not on the 12Cr-1MoVW. Tempering treatment had relatively little effect on the shift in DBTT for both steels. Conclusions are presented on how heat treatment can be used to optimize impact properties.

  6. Heat treatment effects on impact toughness of 9Cr-1MoVNb and 12Cr-1MoVW steels irradiated to 100 dpa

    International Nuclear Information System (INIS)

    Klueh, R.L.; Alexander, D.J.

    1997-01-01

    Plates of 9Cr-1MoVNb and 12Cr-1MoVW steels were given four different heat treatments: two normalizing treatments were used and for each normalizing treatment two tempers were used. Miniature Charpy specimens from each heat treatment were irradiated to ∼19.5 dpa at 365 degrees C and to ∼100 dpa at 420 degrees C in the Fast Flux Test Facility (FFTF). In previous work, the same materials were irradiated to 4-5 dpa at 365 degrees C and 35-36 dpa at 420 degrees C in FFTF. The tests indicated that prior austenite grain size, which was varied by the different normalizing treatments, had a significant effect on impact behavior of the 9Cr-1MoVNb but not on the 12Cr-1MoVW. Tempering treatment had relatively little effect on the shift in DBTT for both steels. Conclusions are presented on how heat treatment can be used to optimize impact properties

  7. Caustic cracking of 2 1/4 CrMo steel

    International Nuclear Information System (INIS)

    Cowen, H.C.; Thorley, A.W.

    1983-12-01

    Stress corrosion cracking tests performed on the 21/4 Cr Mo ferritic steel are described. The principal environments studied were strong, aqueous caustic soda, molten anhydrous caustic soda, and caustic soda with an addition of sodium. Emphasis has been placed on material in the quenched-hardened condition. (author)

  8. Deformation mechanism maps for pure iron, corrosion resistant austenitic steels and a low-alloy carbon steel

    International Nuclear Information System (INIS)

    Frost, H.Y.; Ashby, M.F.

    1980-01-01

    Principles of construction of deformation mechanisms charts for iron base alloys are presented. Deformation mechanisms charts for pure iron, 316 and 314 stainless steels, a ferritic steel with 1% Cr, Mo, V are given, examples of the charts application being provided. The charts construction is based, when it is possible, on the state equations, deduced from theoretical models and satisfying experimental data. The charts presented should be considered as an attempt to unite the main regularities of the theory of dislocations and diffusion with the observed experimental picture of plastic deformation and creep of commercial steels [ru

  9. Elitné prvočísla

    Czech Academy of Sciences Publication Activity Database

    Šolcová, A.; Křížek, Michal

    2006-01-01

    Roč. 35, č. 4 (2006), s. 1-6 ISSN 1335-4981 R&D Projects: GA MŠk 1P05ME749 Institutional research plan: CEZ:AV0Z10190503 Keywords : Fermat numbers * Pepin´s test * quadratic nonresidues Subject RIV: BA - General Mathematics

  10. Dinámica no lineal en la motivación en el trabajo: propuesta de un modelo y resultados preliminares

    OpenAIRE

    Navarro Cid, José; Quijano de Arana, Santiago D. de

    2003-01-01

    Muchos especialistas estarían de acuerdo en que la motivación en el trabajo debe entenderse como un proceso dinámico. Sin embargo, son pocas las investigaciones que se han interesado por la descripción y explicación de dicha dinámica motivacional. Este artículo propone un modelo complejo de motivación en el trabajo que integra tres variables clásicas en la literatura: motivos, autoeficacia e instrumentalidad. El modelo incorpora los cambios que se producen en la motivación a lo largo del tiem...

  11. Anodized Steel Electrodes for Supercapacitors.

    Science.gov (United States)

    Sagu, Jagdeep S; Wijayantha, K G Upul; Bohm, Mallika; Bohm, Siva; Kumar Rout, Tapan

    2016-03-09

    Steel was anodized in 10 M NaOH to enhance its surface texture and internal surface area for application as an electrode in supercapacitors. A mechanism was proposed for the anodization process. Field-emission gun scanning electron microscopy (FEGSEM) studies of anodized steel revealed that it contains a highly porous sponge like structure ideal for supercapacitor electrodes. X-ray photoelectron spectroscopy (XPS) measurements showed that the surface of the anodized steel was Fe2O3, whereas X-ray diffraction (XRD) measurements indicated that the bulk remained as metallic Fe. The supercapacitor performance of the anodized steel was tested in 1 M NaOH and a capacitance of 18 mF cm(-2) was obtained. Cyclic voltammetry measurements showed that there was a large psueudocapacitive contribution which was due to oxidation of Fe to Fe(OH)2 and then further oxidation to FeOOH, and the respective reduction of these species back to metallic Fe. These redox processes were found to be remarkably reversible as the electrode showed no loss in capacitance after 10000 cycles. The results demonstrate that anodization of steel is a suitable method to produce high-surface-area electrodes for supercapacitors with excellent cycling lifetime.

  12. Effects of irradiation on tungsten stabilized martensitic steels*1

    Science.gov (United States)

    Gelles, D. S.; Hsu, C. Y.; Lechtenberg, T. A.

    1988-07-01

    Tungsten stabilized martensitic stainless steels are being developed for fusion reactor first wall applications in order to lower retained radioactivity so as to permit shallow land burial after reactor decommissioning. Two such alloys have been designed, fabricated, fast neutron irradiated in FFTF and examined by transmission electron microscopy. The two compositions were Fe-7.5Cr-2.0W-0.17 C and Fe-10.2Cr-1.7W-0.3V-0.02C. Conditions examined included irradiation temperatures of 365, 426, 520 and 600°C to doses as high as 34 dpa. Small amounts of void swelling are found at the two lowest temperatures. It is demonstrated that levels of tungsten on the order of 2 wt% do not result in excessive intermetallic precipitation under these irradiation conditions.

  13. MC3T3-E1 cell response to stainless steel 316L with different surface treatments

    International Nuclear Information System (INIS)

    Zhang, Hongyu; Han, Jianmin; Sun, Yulong; Huang, Yongling; Zhou, Ming

    2015-01-01

    In the present study, stainless steel 316L samples with polishing, aluminum oxide blasting, and hydroxyapatite (HA) coating were prepared and characterized through a scanning electron microscope (SEM), optical interferometer (surface roughness, Sq), contact angle, surface composition and phase composition analyses. Osteoblast-like MC3T3-E1 cell adhesion on the samples was investigated by cell morphology using a SEM (4 h, 1 d, 3 d, 7 d), and cell proliferation was assessed by MTT method at 1 d, 3 d, and 7 d. In addition, adsorption of bovine serum albumin on the samples was evaluated at 1 h. The polished sample was smooth (Sq: 1.8 nm), and the blasted and HA coated samples were much rougher (Sq: 3.2 μm and 7.8 μm). Within 1 d of incubation, the HA coated samples showed the best cell morphology (e.g., flattened shape and complete spread), but there was no significant difference after 3 d and 7 d of incubation for all the samples. The absorbance value for the HA coated samples was the highest after 1 d and 3 d of incubation, indicating better cell viability. However, it reduced to the lowest value at 7 d. Protein adsorption on the HA coated samples was the highest at 1 h. The results indicate that rough stainless steel surface improves cell adhesion and morphology, and HA coating contributes to superior cell adhesion, but inhibits cell proliferation. - Highlights: • Rough stainless steel surface improves cell adhesion and proliferation. • HA coating results in superior cell morphology and cell attachment. • HA coating inhibits osteoblast cell proliferation after 7 d of incubation

  14. MC3T3-E1 cell response to stainless steel 316L with different surface treatments

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Hongyu [State Key Laboratory of Tribology, Department of Mechanical Engineering, Tsinghua University, Beijing 100084 (China); Han, Jianmin, E-mail: siyanghan@163.com [Dental Materials Laboratory, National Engineering Laboratory for Digital and Material Technology of Stomatology, Peking University School and Hospital of Stomatology, Beijing 100081 (China); Sun, Yulong [State Key Laboratory of Tribology, Department of Mechanical Engineering, Tsinghua University, Beijing 100084 (China); Huang, Yongling [Jinghang Biomedicine Engineering Division, Beijing Institute of Aeronautical Material, Beijing 100095 (China); Zhou, Ming [State Key Laboratory of Tribology, Department of Mechanical Engineering, Tsinghua University, Beijing 100084 (China)

    2015-11-01

    In the present study, stainless steel 316L samples with polishing, aluminum oxide blasting, and hydroxyapatite (HA) coating were prepared and characterized through a scanning electron microscope (SEM), optical interferometer (surface roughness, Sq), contact angle, surface composition and phase composition analyses. Osteoblast-like MC3T3-E1 cell adhesion on the samples was investigated by cell morphology using a SEM (4 h, 1 d, 3 d, 7 d), and cell proliferation was assessed by MTT method at 1 d, 3 d, and 7 d. In addition, adsorption of bovine serum albumin on the samples was evaluated at 1 h. The polished sample was smooth (Sq: 1.8 nm), and the blasted and HA coated samples were much rougher (Sq: 3.2 μm and 7.8 μm). Within 1 d of incubation, the HA coated samples showed the best cell morphology (e.g., flattened shape and complete spread), but there was no significant difference after 3 d and 7 d of incubation for all the samples. The absorbance value for the HA coated samples was the highest after 1 d and 3 d of incubation, indicating better cell viability. However, it reduced to the lowest value at 7 d. Protein adsorption on the HA coated samples was the highest at 1 h. The results indicate that rough stainless steel surface improves cell adhesion and morphology, and HA coating contributes to superior cell adhesion, but inhibits cell proliferation. - Highlights: • Rough stainless steel surface improves cell adhesion and proliferation. • HA coating results in superior cell morphology and cell attachment. • HA coating inhibits osteoblast cell proliferation after 7 d of incubation.

  15. Development of low-chromium, chromium-tungsten steels for fusion

    International Nuclear Information System (INIS)

    Klueh, R.L.; Alexander, D.J.; Kenik, E.A.

    1995-01-01

    High-chromium (9-12% Cr) Cr-Mo and Cr-W ferritic steels are favored as candidates for fusion applications. In early work to develop reduced-activation steels, an Fe-2.25Cr-2W-0.25V-0.1C steel (designated 2.25Cr-2WV) had better strength than an Fe-9Cr-2W-0.25V-0.07Ta-0.1C (9Cr-2WVTa) steel (compositions are in weight percent). However, the 2.25Cr-2WV had poor impact properties, as determined by the ductile-brittle transition temperature and upper-shelf energy of subsize Charpy impact specimens. Because low-chromium steels have some advantages over high-chromium steels, a program to develop low-chromium steels is in progress. Microstructural analysis indicated that the reason for the inferior impact toughness of the 2.25Cr-2WV was the granular bainite obtained when the steel was normalized. Properties can be improved by developing an acicular bainite microstructure by increasing the cooling rate after austenitization. Alternatively, acicular bainite can be promoted by increasing the hardenability. Hardenability was changed by adding small amounts of boron and additional chromium to the 2.25Cr-2WV composition. A combination of B, Cr, and Ta additions resulted in low-chromium reduced-activation steels with mechanical properties comparable to those of 9Cr-2WVTa. (orig.)

  16. Experimental Investigation on Friction and Wear Properties of Different Steel Materials

    OpenAIRE

    M.A. Chowdhury; D.M. Nuruzzaman

    2013-01-01

    Friction coefficient and wear rate of different steel materials are investigated and compared in this study. In order to do so, a pin on disc apparatus is designed and fabricated. Experiments are carried out when different types of disc materials such as stainless steel 314 (SS 314), stainless steel 202 (SS 202) and mild steel slide against stainless steel 314 (SS 314) pin. Experiments are conducted at normal load 10, 15 and 20 N, sliding velocity 1, 1.5 and 2 m/s and relative humidity 70%. A...

  17. Hot Deformation Behavior of 1Cr12Ni3Mo2VN Martensitic Stainless Steel

    Science.gov (United States)

    He, Xiaomao; Jiang, Peng; Zhou, Leyu; Chen, Chao; Deng, Xiaochun

    2017-08-01

    1Cr12Ni3Mo2VN is a new type of martensitic stainless steel for the last-stage blades of large-capacity nuclear and thermal power turbines. The deformation behavior of this steel was studied by thermal compression experiments that performed on a Gleeble-3500 thermal simulator at a temperature range of 850°C to 1200°C and a strain rate of 0.01s-1 to 20s-1. When the deformation was performed at high temperature and low strain rate, a necklace type of microstructures was observed, the plastic deformation mechanism is grain boundary slip and migration, when at low temperature and lower strain rate, the slip bands were observed, the mechanism is intracrystalline slips, and when at strain rate of 20s-1, twins were observed, the mechanism are slips and twins. The Arrhenius equation was applied to describe the constitutive equation of the flow stress. The accuracy of the equation was verified by using the experimental data and the correlation coefficient R2 = 0.9786, and the equation can provide reasonable data for the design and numerical simulation of the forging process.

  18. Estimation of fracture toughness of cast stainless steels during thermal aging in LWR systems-revision 1

    International Nuclear Information System (INIS)

    Chopra, O.K.

    1994-08-01

    This report presents a revision of the procedure and correlations presented earlier in NUREG/CR-4513, ANL-90/42 (June 1991) for predicting the change in mechanical properties of cast stainless steel components due to thermal aging during service in light water reactors at 280-330 degrees C (535-625 degrees F). The correlations presented in this report are based on an expanded data base and have been optimized with mechanical-property data on cast stainless steels aged up to ∼58,000 h at 290-350 degrees C (554-633 degrees F). The fracture toughness J-R curve, tensile stress, and Charpy-impact energy of aged cast stainless steels are estimated from known material information. Mechanical properties of a specific cast stainless steel are estimated from the extent and kinetics of thermal embrittlement. Embrittlement of cast stainless steels is characterized in terms of room-temperature Charpy-impact energy. Charpy-impact energy as a function of time and temperature of reactor service is estimated from the kinetics of thermal embrittlement, which are also determined from the chemical composition. The initial impact energy of the unaged steel is required for these estimations. Initial tensile flow stress is needed for estimating the flow stress of the aged material. The fracture toughness J-R curve for the material is then obtained by correlating room-temperature Charpy-impact energy with fracture toughness parameters. The values of J IC are determined from the estimated J-R curve and flow stress. A common open-quotes predicted lower-boundclose quotes J-R curve for cast stainless steels of unknown chemical composition is also defined for a given grade of steel, range of ferrite content, and temperature. Examples of estimating mechanical properties of cast stainless steel components during reactor service are presented

  19. Procedures for the selection of stopping power ratios for electron beams: Comparison of IAEA TRS procedures and of DIN procedures with Monte Carlo results

    International Nuclear Information System (INIS)

    Roos, M.; Christ, G.

    2000-01-01

    In the International Code of Practice IAEA TRS-381 the stopping power ratios water/air are selected according to the half-value depth and the depth of measurement. In the German Standard DIN 6800-2 a different procedure is recommended, which, in addition, takes the practical electron range into account; the stopping power data for monoenergetic beams from IAEA TRS-381 are used. Both procedures are compared with recent Monte Carlo calculations carried out for various beams of clinical accelerators. It is found that the DIN procedure shows a slightly better agreement. In addition, the stopping power ratios in IAEA TRS-381 are compared with those in DIN 6800-2 for the reference conditions of the beams from the PTB linac; the maximum deviation is not larger than 0.6%. (author)

  20. Plasma nitriding of steels

    CERN Document Server

    Aghajani, Hossein

    2017-01-01

    This book focuses on the effect of plasma nitriding on the properties of steels. Parameters of different grades of steels are considered, such as structural and constructional steels, stainless steels and tools steels. The reader will find within the text an introduction to nitriding treatment, the basis of plasma and its roll in nitriding. The authors also address the advantages and disadvantages of plasma nitriding in comparison with other nitriding methods. .

  1. 49 CFR 178.512 - Standards for steel or aluminum boxes.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Standards for steel or aluminum boxes. 178.512... aluminum boxes. (a) The following are identification codes for steel or aluminum boxes: (1) 4A for a steel box; and (2) 4B for an aluminum box. (b) Construction requirements for steel or aluminum boxes are as...

  2. Dinámica de la identidad, acción y contexto

    Directory of Open Access Journals (Sweden)

    Anne Marie Costalat-Founeau

    2007-06-01

    Full Text Available La identidad social no puede ser considerada más como una imagen fijada y estática que determina las representaciones individuales y/o colectivas. Se inserta, más bien, dentro de una dinámica de representaciones que está marcada por fases biográficas y sociales. Esta impresión social está en parte construida por la experiencia personal impresa en los recuerdos, y transfiere una realidad experiencial a la identidad. La acción participa en esta concretización y también la refuerza: es así que el carácter normativo de la acción parece reforzar su propia manifestación y, por lo tanto, su efecto. Esos efectos tienen un poder central en la dinámica de la identidad. La acción se ubica en el centro de la subjetividad, pues pone en relación las aspiraciones, las representaciones y también los valores y el sentimiento de capacidad: la acción favorece una relación estrecha entre los factores afectivos y cognitivos. Esos factores actúan en conjunto elaborando regulaciones dinámicas y organizando fases de identidad más o menos conflictivas. Se presentan los efectos de la acción sobre la subjetividad.---Social identity should not be considered anymore as a fixed and static image that defines individual or collective representations. It is embedded within a representational dynamic where biographical and social phases left their marks. This social imprint is partly made by the experience ingrained in the remembrance that gives all its experiential reality to identity. Action participates and reinforces this concreteness. It seems that the prescriptive nature of action reinforces its presence and therefore its effects. More precisely, these effects, which are inherent to action, possess a central power in the identity dynamic. Action is at the heart of subjectivity in the sense that it connects aspirations, representations, as well as the values of the individual and the sense of his own capacity. It involves the tight interweaving of

  3. Steel

    International Nuclear Information System (INIS)

    Zorev, N.N.; Astafiev, A.A.; Loboda, A.S.; Savukov, V.P.; Runov, A.E.; Belov, V.A.; Sobolev, J.V.; Sobolev, V.V.; Pavlov, N.M.; Paton, B.E.

    1977-01-01

    Steels also containing Al, N and arsenic, are suitable for the construction of large components for high-power nuclear reactors due to their good mechanical properties such as good through-hardening, sufficiently low brittleness conversion temperature and slight displacement of the latter with neutron irradiation. Defined steels and their properties are described. (IHOE) [de

  4. Helium-induced weld degradation of HT-9 steel

    International Nuclear Information System (INIS)

    Wang, Chin-An; Chin, B.A.; Lin, Hua T.; Grossbeck, M.L.

    1992-01-01

    Helium-bearing Sandvik HT-9 ferritic steel was tested for weldability to simulate the welding of structural components of a fusion reactor after irradiation. Helium was introduced into HT-9 steel to 0.3 and 1 atomic parts per million (appm) by tritium doping and decay. Autogenous single pass full penetration welds were produced using the gas tungsten arc (GTA) welding process under laterally constrained conditions. Macroscopic examination showed no sign of any weld defect in HT-9 steel containing 0.3 appm helium. However, intergranular micro cracks were observed in the HAZ of HT-9 steel containing 1 appm helium. The microcracking was attributed to helium bubble growth at grain boundaries under the influence of high stresses and temperatures that were present during welding. Mechanical test results showed that both yield strength (YS) and ultimate tensile strength (UTS) decreased with increasing temperature, while the total elongation increased with increasing temperature for all control and helium-bearing HT-9 steels

  5. Chemical decontamination of stainless steel

    International Nuclear Information System (INIS)

    Onuma, Tsutomu; Akimoto, Hidetoshi

    1991-01-01

    The present invention concerns a method for chemical decontamination of radioactive metal waste materials contaminated with radioactive materials on the surface, generated in radioactive materials-handling facilities. The invention is comprised of a method of chemical decontamination of stainless steel, characterized by comprising a first process of immersing a stainless steel-based metal waste material contaminated by radioactive materials on the surface in a sulfuric acid solution and second process of immersing in an aqueous solution of sulfuric acid and oxidizing metal salt, in which a portion of the surface of the stainless steel to be decontaminated is polished mechanically to expose a portion of the base material before the above first and second processes. 1 figs., 2 tabs

  6. Corrosion of path A PCA and 12 Cr-1 MoVW steel in thermally convective lithium

    International Nuclear Information System (INIS)

    Tortorelli, P.F.; DeVan, J.H.

    1984-01-01

    Exposure of path A PCA alloys to thermally convective lithium for 6700 h at 600 and 570 0 C resulted in corrosion reactions that were similar to what is observed for other austenitic alloys exposed under similar conditions. It corroded more rapidly than type 316 stainless steel, and the presence of nitride stringers in PCA did not affect the measured weight losses. Consideration of the weight change and surface analysis data for 12 Cr-1 MoVW steel exposed to thermally convective lithium between 500 and 350 0 C for 10,088 h revealed that reactions with carbon and nitrogen were probably the principal corrosion processes for this alloy in this temperature range. Corrosion was not severe

  7. Experimental study on kinematic hardening of 1Cr18Ni9Ti stainless steel under low cycle fatigue

    International Nuclear Information System (INIS)

    Shao Er; Yang Xianjie; Mao Jianghui; Sun Yafang

    2006-01-01

    To study the effect of the monotonic loading on subsequent cyclic plastic hardening and flow properties of 1Cr18Ni9Ti steel, an experimental study of the low cycle fatigue tests with mean strains for 1Cr18Ni9Ti stainless steel was carried out. An analysis on the evolutions of the yield surface radius and the back stresses under symmetric and asymmetric cyclic strain loading with different strain amplitudes was made. The dependence of the evolutions of the material kinematic hardening and isotropic hardening on the strain amplitude and mean strain was observed. These results provide the experimental foundation for the constitutive model of the material under combined monotonic and cyclic complicated loads. (authors)

  8. Microstructural characterization of 5-9% chromium reduced-activation steels

    International Nuclear Information System (INIS)

    Jayaram, R.; Klueh, R.L.

    1997-01-01

    The microstructures of a 9Cr-2W-0.25-0.1C (9Cr-2WV), a 9Cr-2W-0.25V-0.07Ta-0.1C (9Cr-2WVTa), a 7Cr-2W-0.25V-0.07Ta-0.1C (7Cr-2WVTa), and a 5Cr-2W-0.25V-0.07Ta-0.1C (5Cr-2WVTa) steel (all compositions are in weight percent) have been characterized by Analytical Electron Microscopy (AEM) and Atom Probe Field Ion Microscopy (APFIM). The matrix in all four reduced-activation steels was 100% martensite. In the two 9Cr steels, the stable precipitates were blocky M 23 C 6 and small spherical MC. The two lower-chromium steels contained blocky M 7 C 3 and small needle-shaped carbonitrides in addition to M 23 C 6 . AEM and APFIM analysis revealed that in the steels containing tantalum, the majority of the tantalum was in solid solution. The experimental observations were in good agreement with phases and compositions predicted by phase equilibria calculations

  9. Tool steels

    DEFF Research Database (Denmark)

    Højerslev, C.

    2001-01-01

    On designing a tool steel, its composition and heat treatment parameters are chosen to provide a hardened and tempered martensitic matrix in which carbides are evenly distributed. In this condition the matrix has an optimum combination of hardness andtoughness, the primary carbides provide...... resistance against abrasive wear and secondary carbides (if any) increase the resistance against plastic deformation. Tool steels are alloyed with carbide forming elements (Typically: vanadium, tungsten, molybdenumand chromium) furthermore some steel types contains cobalt. Addition of alloying elements...... serves primarily two purpose (i) to improve the hardenabillity and (ii) to provide harder and thermally more stable carbides than cementite. Assuming proper heattreatment, the properties of a tool steel depends on the which alloying elements are added and their respective concentrations....

  10. Effect of Al Hot-Dipping on High-Temperature Corrosion of Carbon Steel in N2/0.1% H2S Gas

    Directory of Open Access Journals (Sweden)

    Muhammad Ali Abro

    2016-02-01

    Full Text Available High-temperature corrosion of carbon steel in N2/0.1% H2S mixed gas at 600–800 °C for 50–100 h was studied after hot-dipping in the aluminum molten bath. Hot-dipping resulted in the formation of the Al topcoat and the Al-Fe alloy layer firmly adhered on the substrate. The Al-Fe alloy layer consisted primarily of a wide, tongue-like Al5Fe2 layer and narrow Al3Fe layer. When corroded at 800 °C for 100 h, the Al topcoat partially oxidized to the protective but non-adherent α-Al2O3 layer, and the interdiffusion converted the Al-Fe alloy layer to an (Al13Fe4, AlFe3-mixed layer. The interdiffusion also lowered the microhardness of the hot-dipped steel. The α-Al2O3 layer formed on the hot-dipped steel protected the carbon steel against corrosion. Without the Al hot-dipping, the carbon steel failed by forming a thick, fragile, and non-protective FeS scale.

  11. Ultrasonic testing of austenitic stainless steel welds

    International Nuclear Information System (INIS)

    Nishino, Shunichi; Hida, Yoshio; Yamamoto, Michio; Ando, Tomozumi; Shirai, Tasuku.

    1982-05-01

    Ultrasonic testing of austenitic stainless steel welds has been considered difficult because of the high noise level and remarkable attenuation of ultrasonic waves. To improve flaw detectability in this kind of steel, various inspection techniques have been studied. A series of tests indicated: (1) The longitudinal angle beam transducers newly developed during this study can detect 4.8 mm dia. side drilled holes in dissimilar metal welds (refraction angle: 55 0 from SUS side, 45 0 from CS side) and in cast stainless steel welds (refraction angle: 45 0 , inspection frequency: 1 MHz). (2) Cracks more than 5% t in depth in the heat affected zones of fine-grain stainless steel pipe welds can be detected by the 45 0 shear wave angle beam method (inspection frequency: 2 MHz). (3) The pattern recognition method using frequency analysis technology was presumed useful for discriminating crack signals from spurious echoes. (author)

  12. Accelerated development of advanced steels for nuclear applications

    International Nuclear Information System (INIS)

    Ghoniem, N.; Zinkle, S.

    2009-01-01

    Significant progress has been achieved in the operational performance and radiation resistance of ferritic-martensitic steels during the past few decades. Conventional high temperature steels, such as HT-9 and 2 1/4 Cr-1Mo have evolved into super Oxide Dispersion Strengthened (ODS) steels through successive optimization to meet strict performance and radiation-resistance constraints. Such evolution was possible through a combination of experimentation, modeling and empirical information. Further development and optimization of structural steels in nuclear applications will require full utilization of the available array of sophisticated experimental techniques and multiscale computational modeling, in addition to empirical data. We present here a systematic approach to the process of optimum steel development, by linking material fabrication to thermo-mechanical properties through a physical understanding of microstructure evolution. The optimization process is based on the application of design constraints (e.g. low activation, low DBTT, low swelling, creep resistance, and weldability) to describe the required microstructures, which in turn, can be controlled through material processing techniques. Prospects for future design of optimum structural steels in nuclear applications by utilization of the hierarchy of multiscale experimental and computational strategies will be described. (author)

  13. Dinámica del ciclo del nitrógeno y fósforo en suelos

    Directory of Open Access Journals (Sweden)

    Fabio Ancízar Aristizábal Gutiérrez

    2012-01-01

    Full Text Available Título en ingles: Nitrogen and phosphorus cycles dynamics in Soils Resumen: Los ciclos biogeoquímicos del fósforo (P y del nitrógeno (N son sistemas dinámicos que suceden a través de la biosfera, de cuyos mecanismos de transformación depende la disponibilidad de estos elementos para diferentes formas de vida.  Se acepta que la diversidad y actividad de las poblaciones microbianas posee un papel crucial en la dinámica de los nutrientes y por tanto el desafío está en comprender, como responden a las condiciones ambientales. La actividad microbiana en los suelos depende tanto de la condición del recurso y como de sus propiedades químicas, físicas y biológicas.  En este documento se describen conceptos que se han empleado para entender la dinámica del nitrógeno y el fósforo, con el propósito de discutir cómo las características de las diferentes fracciones orgánicas y minerales seleccionan el potencial biológico encargado del recambio de dichos elementos,  panorama que actualmente se aborda a través de técnicas independientes del cultivo para estudiar las poblaciones microbianas in situ.  Palabras clave: dinámica de N y P; disponibilidad de nutrientes en suelo; fracciones orgánicas e inorgánicas y actividad microbiana. Abstract: Biogeochemical cycle’s phosphorus (P and nitrogen (N are dynamic systems taking place through the biosphere, whose mechanisms of transformation depends on the availability of these elements for different forms of life.  It is accepted that the diversity and activity of microbial populations plays a crucial role in nutrient dynamics and therefore the challenge is to understand how they respond to environmental conditions. Microbial activity in soils depends on both the resource condition and its chemical, physical and biological properties. Concepts described herein have been used to understand the nitrogen and phosphorus dynamics, with the aim to discuss how the characteristics of the

  14. Mechanical properties data of 2-1/4Cr-1Mo steel for the experimental very high temperature gas-cooled reactor

    International Nuclear Information System (INIS)

    Oku, Tatsuo; Kikuyama, Toshihiko; Fukaya, Kiyoshi; Kodaira, Tsuneo

    1978-11-01

    This is a collection of mechanical properties data of 2-1/4Cr-1Mo steel necessary for structural design and safety analysis of the pressure vessel of the Experimental Very High Temperature Gas-Cooled Reactor (VHTR). These include physical properties, mechanical properties, temper embrittlement, creep with fatigue, fracture toughness and irradiation effects. A review of the data shows the research areas to be carried out particularly in the future for more data. (author)

  15. The Effect of Stepped Austempering on Phase Composition and Mechanical Properties of Nanostructured X37CrMoV5-1 Steel

    Directory of Open Access Journals (Sweden)

    Marciniak S.

    2015-04-01

    Full Text Available This paper presents the results of studies of X37CrMoV5-1 steel subjected to quenching processes with a one-step and a two-step isothermal annealing. The TEM observation revealed that steel after one-step treatment led is composed of carbide-free bainite with nanometric thickness of ferrite plates and of high volume fraction of retained austenite in form of thin layers or large blocks. In order to improve the strength parameters an attempt was made to reduce the austenite content by use of quenching with the two-step isothermal annealing. The temperature and time of each step were designed on the basis of dilatometric measurements. It was shown, that the two-step heat treatment led to increase of the bainitic ferrite content and resulted in improvement of steel's strength with no loss of steel ductility.

  16. In-situ Raman and X-ray photoelectron spectroscopic studies on the pitting corrosion of modified 9Cr-1Mo steel in neutral chloride solution

    Science.gov (United States)

    Ramya, S.; Nanda Gopala Krishna, D.; Mudali, U. Kamachi

    2018-01-01

    In-situ Raman and X-ray photoelectron spectroscopic studies were performed for the identification of native and corroded surface oxide layers of modified 9Cr-1Mo steel. The Raman data obtained for native oxide layer of modified 9Cr-1Mo steel revealed that it was mainly composed of oxides of Fe and Cr. The presence of alloying element Mo was found to be less significant in the native oxide film. The oxides of Cr were dominant at the surface and were found to be decreasing closer to metal/oxide layer interface. The changes in the chemical composition of the native films upon in-situ pitting during potentiostatic polarization experiment were characterized by in-situ Raman analysis. The corrosion products of potentiostatically polarized modified 9Cr-1Mo steel was composed of dominant Fe (III) phases viz., γ- Fe2O3, α and γ - FeOOH along with the oxides of chromium. The results from Raman analysis were corroborated with the XPS experiments on as received and pitted samples of modified 9Cr-1Mo steel specimens. It was observed that the oxides of Cr and Mo contributed for the stability of the surface layer by forming Cr2O3 and MoO3. Also, the study attempted to find out the intermediate corrosion products inside the metastable pits to account for the pseudo passive behavior of modified 9Cr-1Mo steel in 0.1 M NaCl solution.

  17. Passivation Characteristics of Alloy Corrosion-Resistant Steel Cr10Mo1 in Simulating Concrete Pore Solutions: Combination Effects of pH and Chloride.

    Science.gov (United States)

    Ai, Zhiyong; Sun, Wei; Jiang, Jinyang; Song, Dan; Ma, Han; Zhang, Jianchun; Wang, Danqian

    2016-09-01

    The electrochemical behaviour for passivation of new alloy corrosion-resistant steel Cr10Mo1 immersed in alkaline solutions with different pH values (13.3, 12.0, 10.5, and 9.0) and chloride contents (0.2 M and 1.0 M), was investigated by various electrochemical techniques: linear polarization resistance, electrochemical impedance spectroscopy and capacitance measurements. The chemical composition and structure of passive films were determined by XPS. The morphological features and surface composition of the immersed steel were evaluated by SEM together with EDS chemical analysis. The results evidence that pH plays an important role in the passivation of the corrosion-resistant steel and the effect is highly dependent upon the chloride contents. In solutions with low chloride (0.2 M), the corrosion-resistant steel has notably enhanced passivity with pH falling from 13.3 to 9.0, but does conversely when in presence of high chloride (1.0 M). The passive film on the corrosion-resistant steel presents a bilayer structure: an outer layer enriched in Fe oxides and hydroxides, and an inner layer, rich in Cr species. The film composition varies with pH values and chloride contents. As the pH drops, more Cr oxides are enriched in the film while Fe oxides gradually decompose. Increasing chloride promotes Cr oxides and Fe oxides to transform into their hydroxides with little protection, and this is more significant at lower pH (10.5 and 9.0). These changes annotate passivation characteristics of the corrosion-resistant steel in the solutions of different electrolyte.

  18. 30 CFR 57.7050 - Tool and drill steel racks.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Tool and drill steel racks. 57.7050 Section 57... Rotary Jet Piercing Drilling-Surface and Underground § 57.7050 Tool and drill steel racks. Receptacles or racks shall be provided for drill steel and tools stored or carried on drills. ...

  19. How massive is the black hole at the centre of our Galaxy?

    Czech Academy of Sciences Publication Activity Database

    Křížek, Filip; Křížek, Michal; Šolc, Jakub

    2007-01-01

    Roč. 36, č. 1 (2007), s. 43-51 ISSN 1335-4981 Institutional research plan: CEZ:AV0Z10190503; CEZ:AV0Z10480505 Keywords : Schwarzschild radius * Kepler´s laws * numerical excentricity Subject RIV: BA - General Mathematics

  20. Volcano deformation analysis based an on-demand DInSAR-GRID system: the SBAS-GPOD solution

    Science.gov (United States)

    Manunta, M.; Casu, F.; Cossu, R.; Fusco, L.; Guarino, S.; Lanari, R.; Mazzarella, G.; Sansosti, E.

    2009-04-01

    Differential SAR Interferometry (DInSAR) has already demonstrated to be an effective technique to detect and monitor ground displacements with centimeter accuracy. Moreover, the recent development of advanced DInSAR techniques, aimed at the generation of deformation time series, has led to the exploitation of the large archive of SAR data acquired all over the world, during the last 16 years, by the ERS, ENVISAT and RADARSAT satellites. Among these advanced approaches, we focus on the Small BAseline Subset (SBAS) algorithm that relies on the combination of DInSAR data pairs, characterized by a small separation between the acquisition orbits (baseline), in order to produce mean deformation velocity maps and the corresponding time series, maximizing the coherent pixel density of the investigated area. One of the main capabilities of the SBAS approach is the possibility to work at two spatial resolution scales, thus allowing us to investigate deformation phenomena affecting both extended areas (with resolution of about 100 by 100 m) and selected zones, in the latter case highlighting localized displacements that may affect single structures or buildings (at the full instrument resolution). Similarly to other advanced DInSAR techniques, the SBAS approach requires extended data storage and processing capabilities due to the large amount of data exploited for the generation of the final products. Accordingly, we present in this work the results of the first experiment to "plug" the robustness of the SBAS algorithm into the high computing capability provided by a GRID-based system. In particular, we have exploited the low-resolution SBAS algorithm [1] and the ESA Grid Processing-on-Demand (G-POD) system. This environment is one of the results achieved by the ESA Science and Application Department of Earth Observation Programmes Directorate at ESRIN that focused, following the participation to the DATAGRID project (the first large European Commission funded Grid project