WorldWideScience

Sample records for steel-18kh2n4va

  1. On the corrosion resistance of 01Kh25 ferritic steel

    International Nuclear Information System (INIS)

    Eremeeva, R.A.; Koval', E.K.

    1989-01-01

    Effect of non-ferrous metal ions on corrosion behaviour of 01Kh25 specific low carbon steel as compared to austenitic 12Kh18N10T and 06KhN28MDT steels in boiling solutions of sulfuric and nitric acids and their mixture is studied. Compositions initating commercial ones are chosen the media. It is shown that trough corrosion resistance of 01Kh25 steel in 10% H 2 SO 4 is two order below 06KhN28MDT austenitic steel in presence of Cu 2+ ions as a result of the surface passivation corrosion resistance of ferritic steel is an order higher the austenitic ones. Ferrite steel resistance in the nitric acid and its mixture with sulfuric acid is five timesas much as in 12Kh18N10T austenitic steel

  2. Ultrasound surface treatment of Kh18N10T steel with different structural state. Ul'trazvukovaya poverkhnostnaya obrabotka stali Kh18N10T s razlichnym strukturnym sostoyaniem

    Energy Technology Data Exchange (ETDEWEB)

    Aksenov, V K; Danilov, P A; Mats, A V; Netesov, V M; Yaes, A A [AN Ukrainskoj SSR, Kharkov (Ukrainian SSR). Fiziko-Tekhnicheskij Inst.

    1989-09-01

    Ultrasound surface treatment (USST) is studied for its effect on the structure and mechanical-and-physical properties of Kh18N10T steel with different prehistory. It is shown that surface treatment may both increase and decrease steel microhardness.

  3. Effect of rolling temperature on 12Kh18N10T steel tube hardening

    International Nuclear Information System (INIS)

    Yushkevich, P.M.; Stepanovich, V.E.; Manankova, L.V.; Usenko, V.N.; Semenov, I.A.

    1984-01-01

    Mechanical properties and substructure of tubes at the constant reduction degree k(the ratio of deformation over wall thickness to deformation over diameter), depending on strain degree during cold and hot tube rolling, have been studied. The investigations are carried out using hot-rolled tubes with the dimensions 88x8 mm of 12Kh1hN10T steel. With the decrease of strain over the wall of the tube, produced of 12Kh18N10T steel as to strain over diameter the values of yield strength and ultimate strength increase with simultaneous decrease in ductility during warm rolling and yield strength and ultimate strength decrease with the increase in ductility-during cold rolling. During warm rolling of the tubes at 250 deg C the hardening of 12Kh18N10T steel is higher, than at the rolling temperature 150 deg C. The optimum temperature range of warm rolling is 120-150 deg C. Grain orientation in the metal of the tubes and degree of texture perfection increase with the temperature increase of the tube warm drolling as compared with col rolli

  4. Influence of local microplastic strains on stress corrosion of 08Kh18N10T steel

    International Nuclear Information System (INIS)

    Moskvin, L.N.; Efimov, A.A.; Sherman, Ya.I.; Fedorova, T.I.

    1987-01-01

    Study on specific features of microhomogeneous strain in the process of plastic strain development and their role in stress corrosion of 08Kh18N10T steel sheet specimens subject to preliminary strain by 1, 3, 6, 16 and 23% and subsequent tests of stress corrosion in magnesium chloride solution at 150 deg C 140 MPa has been carried out. Analysis of test results has shown that microplastic strain is distributed over a specimen nonuniformly and is accompanied with the slip bands formation which are sources of corrosion crack origination and development. 08Kh18N10T steel manifests the highest trend to stress corrosion under 1% microplastic strain

  5. Development of plastic deformations in 12Kh18N10T steel under cyclic symmetrical bending of specimens of various length

    Energy Technology Data Exchange (ETDEWEB)

    Pisarenko, G.S.; Leonets, V.A.; Bega, N.D. (AN Ukrainskoj SSR, Kiev. Inst. Problem Prochnosti)

    1983-08-01

    Effect of specimen length on intensity of plastic deformation development and cyclic strength is studied for annealed 12Kh18N10T steel under cyclic symmetrical bending. The intensity of microplastic deformations and cyclic strength of annealed 12Kh18N10T steel in the considered case is due to self-heating.

  6. Nitrogen-containing superlow-carbon austenitic steel 02Kh25N22AM2

    Science.gov (United States)

    Fe'ldgandler, É. G.; Svistunova, T. V.; Savkina, L. Ya.; Lapshina, O. B.

    1996-02-01

    At present the equipment for manufacturing carbamide mineral fertilizers is produced from domestic steel 03Kh17N14M3 having "carbamide quality." Imported equipment also used in the industry is produced from steel of the 25-22-2 (Cr -Ni-Mo) type shipped by various firms, namely, 2RE69 (Sandvik, Sweden), 254SFER (Avesta, Sweden), 2522LCN (VDM, Germany), DM 1.4466 (Germany), and X2CrNiMo 25-22-2 (Dalmine, Italy). The imported steels are used because in some units steel 03Khl7Nl4M3 does not provide the requisite corrosion resistance in an intensified process of carbamide manufacturing. We currently possess domestic high-alloyed steel for producing new and repairing imported equipment operating under the severe conditions of carbamide synthesis. The present paper concerns the structure, mechanical properties, and corrosion resistance of industrially produced steel 02Kh25N22AM2 (ChS-108) and the recommended range of its application.

  7. Structural changes in surface layer of steel 08Kh18N10T during machining

    International Nuclear Information System (INIS)

    Palenik, J.; Vodarek, V.

    1989-01-01

    The results are reported of a study of the surface layer of steel 08Kh18N10T affected by machining. Structural changes were studied caused by finish turning and by additional roller burnishing. Multiple deformation bands were observed to occur under the given cutting conditions; they mainly consisted of deformation doublets and only in isolated cases of ε-martensite. The presence of α'-martensite was not shown in the specimen surface layer following finish turning. The deformation shear bands in the roller-burnished specimen consisted of both ε-martensite and of deformation doublets. The amount of ε-martensite in the structure was significantly higher than in the specimen worked by turning. Local presence of α'-martensite formations was observed inside the deformation bands. It thus follows that roller burnishing is unsuitable as part of the manufacture of components from steel 08Kh18N10T. (J.B.). 5 figs., 1 tab., 9 refs

  8. Preliminary heat treatment of 4KhM2Fch die steel

    International Nuclear Information System (INIS)

    Leonidov, V.M.; Berezkin, Y.A.; Nikitenko, E.V.

    1986-01-01

    To improve the machinability and preparation of the structure for hardening, die steels are given a preliminary treatment which provides a reduction in hardness as a result of separation in the structure of the carbide and ferrite phases, coagulation of the carbides, and acquisition by them of a granular form and also the obtaining of fine grains and a uniform distribution of the structural constituents. The microstructure was evaluated after etching in 4% nital on an MIM-8M microscope. The 4KhM2Fch steel was given a preliminary heat treatment of normalize and anneal. It was concluded that for 4KhM2Fch steel a preliminary heat treatment of normalizing from 950 0 C with a hold of 1.5-2 h, annealing at 750-760 0 C with a hold of 2-3 h, cooling to the isothermal temperature of 670-680 0 C with a hold of 3-4 h, and further air cooling is recommended. The structure after such a heat is granular pearlite with a rating 1-2 and a hardness of 220-250 HB

  9. Heat affected zone structure in welded joints of 15Kh1M1FL, 25Kh2NMFA and 20KhN2MFA steels

    International Nuclear Information System (INIS)

    Levenberg, N.E.; German, S.I.; Fomina, O.P.; Netesa, E.M.; Tsaryuk, A.K.; Kornienko, T.A.

    1983-01-01

    Heat affected zone (HAZ) structure of thick-walled, nature joints of 15Kh1M1FL steel for block structure of power reactors and 25Kh2NMFA and 20KhN2MFA steels for rotors - is investigated. Multi-layer arc welding is performed under conditions being created for standard components of turbines. Thermokinetics diagrams of austenite decomposition are built, phase composition and character of the structure forming at HAZ in the process of welding with preheating are studied. It is shown that at HAZ in joints of the steels under consideration in the process of welding with preheating is formed a structure of a grained bainite which is uniform in its structure and phase composition. Small volumes of round and elongated forms consisting of martensite and residual austenite are distributed in α-solid solution of the bainite. The bainite of the HAZ in welded joints possesses high hardness and great stability in the process of tempering

  10. Effect of partial oxygen pressure on physicochemical properties of Kh18N10T steel at isothermal oxidation

    International Nuclear Information System (INIS)

    Alekseev, V.N.; Oshe, E.K.; Fokin, M.N.; Bogdanova, S.V.; Loskutov, A.I.

    1990-01-01

    Auger-electron spectroscopy, photoelectric polarization, conductometry methods have been used to analyze chemical and defect composition of surface oxide layers, formed on stainless steel Kh18N10T in vacuum (10 -9 - 10 -2 torr) and at temperatures 593-673 K. The boundary conditions of manifestation of extermal behaviour of the dependence of the surface oxide growth rate at isothermal oxidation of this steel are determined. The relation between passivation properties of the surface oxide and the magnitude of the edge angle of the surface wetting with molten tin is revealed

  11. Effect of agressive medium movement of local corrosion of the steel - 12Kh18N10T

    International Nuclear Information System (INIS)

    Makartsev, V.V.; Pakhomov, V.S.; Abramova, I.M.

    1980-01-01

    The effect of agressive medium movement on the formation of pitting corrosion of the 12Kh18N10T stainless steel in the acidic chloride-nitrate solution at room temperature is studied. It is established that the agressive medium movement hinders the formation of pitting corrosion at potentials more negative than +0.4 V and practically does not affect it at more positive potentials. The investigations have been carried out on a disc electrode rotating at a speed from 0 to 2000 rot./min

  12. Mechanical properties and kinetics of bainite transformation in the 35KhN3MFA and 25KhN3MFA steels

    International Nuclear Information System (INIS)

    Korotushenko, G.V.; Grigorkin, V.I.; Kozlov, V.I.; Sandomirskij, M.M.; Krivonosova, L.F.

    1978-01-01

    The mechanical properties and phase composition of the 25KhN3M A and 25KhN3M A bainitic steels have been investigated under austenization temperature varying from 870 to 1180 deg C and quenching cooling rate varying from 1 to 18x10 3 deg/min. Roentgen and quantitative phase analyses were employed. When bainitic steels are subjected to quenching by cooling with slow rate, their structure reveals b.c.c.-bainite with carbon content below the steel average, tetragonal martensite with a higher carbon content, carbon-rich residual austenite and carbides. Decreasing quenching cooling rates increase the concentration of tetragonal martensite and residual austenite and correspondingly reduce the concentration of b.c.c.-bainite. This tends to degrade the structural strength of bainitic steels in cores of large-size forged products

  13. Welding procedure for 06Kh13N7D2 steel

    International Nuclear Information System (INIS)

    Muromtsev, B.I.; Turkov, I.I.

    1990-01-01

    Based on the results of investigations into the process strength, mechanical and corrosion properties of 08Kh13N7D2 steel welded joints, the optimal method of its welding and a possibility of applying it for high-strength mounting in nuclear power plants are determined

  14. Effect of partial oxygen pressure on physicochemical properties of Kh18N10T steel at isothermal oxidation. Vliyanie partsial'nogo davleniya kisloroda na fiziko-khimicheskie svojstva poverkhnosti stali Kh18N10T pri izotermicheskom okislenii

    Energy Technology Data Exchange (ETDEWEB)

    Alekseev, V N; Oshe, E K; Fokin, M N; Bogdanova, S V; Loskutov, A I [AN SSSR, Moscow (USSR). Inst. Fizicheskoj Khimii

    1990-10-01

    Auger-electron spectroscopy, photoelectric polarization, conductometry methods have been used to analyze chemical and defect composition of surface oxide layers, formed on stainless steel Kh18N10T in vacuum (10{sup -9} - 10{sup -2} torr) and at temperatures 593-673 K. The boundary conditions of manifestation of extermal behaviour of the dependence of the surface oxide growth rate at isothermal oxidation of this steel are determined. The relation between passivation properties of the surface oxide and the magnitude of the edge angle of the surface wetting with molten tin is revealed.

  15. The effect of thermal treatment on corrosion properties of 0Kh15N16M3B stainless steel tested in the N2O4 boiling medium

    International Nuclear Information System (INIS)

    Kamenev, A.Ya.; Kopets, Z.V.; Mel'nikova, N.N.; Dergaj, A.M.; Fedyushin, E.E.

    1985-01-01

    The experimental data on the effect of thermal treatment on corrosion properties of stainless steel 00Kh16n15m3b tested in the N 2 O 4 boiling medium at 8.0 MPa and 433 K are presented. The electron microscope data on steel microstructure after different heat treatments and phase composition of oxide films emerging at corrosion test are given. It is shown, that the rise of the heat treatment temperature from 823 up to 1023 K increases total corrosion of 00Kh16n15m3b steel under given test conditions and practically does't affect intercrystalline corrosion. Developed oxide layers are of deposited nature and doesn't affect markedly the rate of progress of the corrosive processes. Taking into account high chromium volatility in vacuum one can assume that at the initial stages of the coolant effect, the process of depletion of steel surface by chromium durng heat treatment affects markedly steel corrosion stability

  16. Corrosion resistance of welded joints in 08Kh22N6T and 08Kh21N6M2T steels made with new electrodes

    International Nuclear Information System (INIS)

    Sidorkina, Y.S.; Leibzon, V.M.; Mankevich, T.V.; Sidlin, E.A.; Zheltova, G.A.

    1986-01-01

    This paper examines the corrosion resistance of 08Kh22N6T and 08Kh21N6M2T steels which would make it possible to ensure equal properties of all the zones of the welded joints. The investigations were carried out on the welded joints in the steels produced with new OZL-40 and OZL-41 electrodes and with standard TsL-11 and EA-400/10u electrodes. The chemical compositions of the steels and deposited metal are presented. The tests of the intercrystalline corrosion resistances of the welded joints in the steels in the as-welded condition and after heat treatment showed that the weld metal is not attacked by intercrystalline corrosion. The tests also showed that the welded joints in 08Kh22N6T steel made with the OZL-40 and TsL-11 electrodes are resistant to corrosion in 55% phosphoric acid at 90 C in 1% sulfuric acid, and in 25% formic acid at 80 C. The investigated steels made with the OZL-40 and OZL-41 electrode respectively show that the welded joints are resistant to intercrystalline and general corrosion, have high mechanical and processing properties and the electrodes, and can be used for welding equipment designed for service in alkaline, neutral, and slightly acid media

  17. Ductile fracture of two-phase welds under 77K. [Steel-EhP810, steel-EhP666, steel-08Kh18N10T, steel-EhP659-VI, steel-chP810

    Energy Technology Data Exchange (ETDEWEB)

    Yushchenko, K.A.; Voronin, S.A.; Pustovit, A.I.; Shavel' , A.V.

    The effect of the type of welding and fillers on crack resistance of welded joints high-strength steel EhP810 and its various compounds with steels EhP666, 08Kh18N10T has been studied. For the welding of steel EhP810 with steels EhP810, EhP666, 08Kh18N10T electron-beam, automatic, argon tungsten arc with non-consumable electrode with various fillers, as well as argon metal-arc welding with consumable electrode, were used. It is shown, that for a joint, made by electron-beam welding, parameters sigmasub(u), Ksub(IcJ), KCV are higher than for a joint of a similar phase structure made using filler wire EhP659-VI. It is explained by the fact, that during electron-beam welding joint metal refining takes place, which removes gases. In welded joints of chP810 steel, having joints with austenitic structure, characteristic of crack resistance Ssub(c) increases by more than 0.2 mm in contrast to two-phase joints, which conventional yield strength at 77 K exceeds 1000 MPa. It is worth mentioning, that for other classes of steels formation of two-phase structure of joint increases welded joint resistance to brittle fracture. It is possible to obtain the required structure of joint with assigned level of resistance to brittle fracture by means of the use of different fillers, optimum and welding procedure, regulating the part of the basic metal in joint content.

  18. Metallographical procedure for detecting carburized layer in the 12Kh18N10T steel tubes

    International Nuclear Information System (INIS)

    Najmark, S.I.; Shmalenyuk, R.P.

    1977-01-01

    The various causes of the tendency to intercrystalline corrosion of stainless steel tubing were studied. 12Kh18N10T steel tube specimens were metallographically investigated to reveal the presence and depth of the carburized layer. Unlubricated specimens and specimens with the graphite-saltpeter lubrication applied on them were austenized in the temperature range from 950 to 1250 deg C and then exposed to a provoking anneal at 650 deg C for 24 h. All the lubricated specimens showed a carbide network along grain boundaries and intercrystalline cracks. The specimens treated without lubrication had no cracks. The method offered can differentiate poor tube cleaning and the undesirable effect of other processing steps on the tubes

  19. Study of surface layer on 08Kh15N5D2T steel

    International Nuclear Information System (INIS)

    Tyurin, A.G.; Povolotskij, V.D.; Zhivotovskij, Eh.A.; Berg, B.N.

    1986-01-01

    08Kh15N5D2T steel phase composition is investigated. Its surface layer was determined by X-ray diffraction analysis method. It is shown, that a subscale appears to be the reason for corrosion of products, made of EhP410 steel. Under the existing smelling technology the carbon content in it is ≥ 0.05%. Therefore to avoid the metal surface depletion with chromium, one must provide for titanium relation to carbon of not less than 4.5 and carry out the rolled product thermal treatment in a protective atmosphere; otherwise, the technology must include not only the removal of scale from steel but the metal subscale layer as well

  20. Irradiation and annealing behavior of 15Kh2MFA reactor pressure vessel steel

    International Nuclear Information System (INIS)

    Popp, K.; Bergmann, U.; Bergner, F.; Hampe, E.; Leonhardt, W.D.; Schuetzler, H.P.; Viehrig, H.W.

    1992-01-01

    This work deals with the mechanical properties of RPV steels used WWER-440. The materials under investigation were a forging (base metal 15Kh2MFA) and the corresponding weld. Charpy V-notch specimens and tensile test specimens were irradiated in the WWER-2 Rheinsberg at about 270 C up to the two neutron fluence levels of 4 x 10 18 and 5 x 10 19 n/cm 2 (E>1MeV). Post-irradiation annealing heat treatments were performed, among others a 475 C/152 h treatment of technical interest. (orig.)

  1. Neutron diffraction study of a nitrogen martensitic steel 0Kh16N4AB under load

    Czech Academy of Sciences Publication Activity Database

    Sumin, V. V.; Papushkin, I.V.; Bannykh, O.A.; Blinov, V.M.; Lukáš, Petr

    2008-01-01

    Roč. 105, č. 1 (2008), s. 88-91 ISSN 0031-918X Institutional research plan: CEZ:AV0Z10480505 Keywords : steel 0Kh16N4AB * neutron diffraction * FSD Subject RIV: BG - Nuclear, Atomic and Molecular Physics , Colliders Impact factor: 0.412, year: 2008

  2. Additional materials for welding of the EP99 heat resisting alloy with the EI868 alloy and 12Kh18N9T steel

    International Nuclear Information System (INIS)

    Sorokin, L.I.; Filippova, S.P.; Petrova, L.A.

    1978-01-01

    Presented are the results of the studies aimed at selecting an additive material for argon-arc welding process involving heat-resistant nickel EP99 alloy to be welded to the EI868 alloy and 12Kh18N9T steel. As the additive material use was made of wire made of nickel-chromium alloys and covered electrodes made of the EP367 alloy with additions of tungsten. It has been established that in order to improve the resistance of metal to hot-crack formation during argon arc welding of the EP99 alloy with the EI868 alloy, it is advisable to use an additive material of the EP533 alloy, and while welding the same alloy with the 12Kh18N9T steel, filler wire of the EP367 alloy is recommended

  3. Features of argon-arc welding of aluminium alloy AD1 to stainless steel 12Kh18N10T

    International Nuclear Information System (INIS)

    Sadov, I.I.

    1982-01-01

    Welding of pipes made of the 12Kh18N10T stainless steel and the AD1 aluminium alloy is proposed to perform using one-sided aluminizing. It is recommended to use shields in order to protect internal and external surfaces of pipes, aluminizing of which is impossible. It is shown that developed technological process for welded joints made of aluminium and stainless steel for cryogenic apparatus permits to create light-duty cryostat assembly using aluminium alloys instead of copper alloys, to increase reliability of apparatus (usage of welded joints instead of soldered ones), and to improve labour conditions

  4. Welding of high-strength stainless steel 03Kh12N10MT for cryogenic engineering

    International Nuclear Information System (INIS)

    Pustovit, A.I.

    1989-01-01

    Consideration is being given to weld resistance to cold and hot cracking at 93 and 77K and to mechanical properties of welded joints of high-strength stainless steel 03Kh12N10MT, produced under the fluxes AN-17M, AN-18, AN-26, AN-45, ANF-5, 48-OF-6, ANK-45 and ANK-49 in combination with various welding wires. It is shown that welds on 03Kh12N10MT steel meet the requirements only when using 48-OF-6 or ANK-49 flux. It is noted that impact strength of welds at 77K is sufficiently affected by the volume fraction of non-metallic inclusions in weld metal

  5. Hardening and stress relaxation during repeated heating of 15Kh2MFA and 15Kh2NMFA steels welded joints

    International Nuclear Information System (INIS)

    Zubchenko, A.S.; Suslova, E.A.

    1986-01-01

    Results of investigation of temperature-time conditions of hardening of welded joints of 15Kh2MFA and 15Kh2NMFA steels and their relaxation resistance, effect of metal structure of imitated heat affected zone (HAZ) on intensity of precipitation hardening at repeated heating are presented as well as the results of the process of relaxation of residual stresses at welded joints samples heating carried out by automatic welding under the flux with the use of adding materials and technology of manufacturing of vessels of WWER-440 and WWER-1000 reactors. Peculiarities of the hardening at repeated heating of the HAZ metal imitated at these steels. Precipitation hardening of overheated 15Kh2MFA steel is connected with precipitations at repeated heating of carbides of the M 7 C 3 , M 3 C and VC type. Stress relaxation in welded joints runs more intensively at the initial stage of repeated heating, i.e. during the same period of the process of dispersed carbide precipitations

  6. Welding of heterogeneous 12Kh2MFSR steels with the Mn-Cr-Si-Ni system

    International Nuclear Information System (INIS)

    Smirnov, A.N.; Belogolov, E.I.

    1978-01-01

    The process of welding pipes of the 12Kh2MFSR pearlitic steels and austenitic steels of the Mn-Cr-Si-Ni system was studied. The filler materials were selected, and the working capacity of welded joints was examined in ageing and cyclic heatings. The microhardness of steels was measured, and the ultimate strength of welded joints was determined. The following has been established: the composite joints of steels of the Mn-Cr-Si-Ni system and 12Kh2MFSR steel are advisable to be welded on a coating layer welded by the EhA395/9 electrodes on the surface of a pipe of the 12Kh2MFSR pearlitic steel; this guarantees the sufficient working capacity of welded joints

  7. Determination of constant of chemical reaction rate in the process of steel treatment in the endothermal atmosphere

    International Nuclear Information System (INIS)

    Gyulikhandanov, E.L.; Kislenkov, V.V.

    1978-01-01

    The high-temperature method was applied to measuring a relative variation in the electrical resistance of a thin steel foil prepared from the 12KhN3A, 18Kh2N4VA, 20KhGNR, and 20Kh3MVF steels during its carburization and decarburization, and determined was the temperature dependence of the reaction rate of the interaction of the endothermal atmosphere of different compositions with the analloyed γ-Fe. A connection has been established between the reaction rate constant and the thermodynamic activity of carbon in the alloyed austenite at the temperature of about 925 deg C, corresponding to the cementation temperature. This provides the quantitative estimation of the above value for any alloyed steels and with the presence of numerical values of diffusion coefficients; this also enables one to carry out an accurate calculation of the distribution of carbon throughout the depth of a layer when effecting the cementation in the endothermal atmosphere

  8. Manufacture of rings of 08Kh18N10T sheet for internal structures of WWER type reactors

    International Nuclear Information System (INIS)

    Fojta, A.; Nitka, B.

    1984-01-01

    Technology is presented of the manufacture of rings for the jacket, shaft, core catcher and shaft bottom of WWER-440 reactors produced by Vitkovice Steel Works. The rings are manufactured from sheets of austenitic steel 08Kh18N10T. The materials and technology problems are discussed of sheet production, ring welding technology and annealing following welding. The plastic properties are assessed of the welded joints and problems are outlined of ring production for WWER-1000 reactors. (B.S.)

  9. Low-temperature cyclic cracking resistance of Fe-Cr-Ni and Fe-Cr-Mn steels welded joints

    International Nuclear Information System (INIS)

    Ostash, O.P.; Zhmur-Klimenko, V.T.; Yarema, S.Ya.; Yushchenko, K.A.; Strok, L.P.; Belotserkovets, V.I.

    1983-01-01

    Results of further investigations into regularities of development of low-temperature fatigue fracture of welded oints in 07Kh13G20AN4 steel are presented, they are compared with analogous data traditional cryogenic 0Kh18N10T and 03Kh13AG19 steels. Welded joints have been prepared by means of automatic V-like level arc Welding of plates; 0Kh18N10T and 07Kh13G20AN4 steels have been welded by means of sv-04Kh19N9 wire, 03Kh13AG19 steel-by means of sv-07Kh13AG19 wire. Tests at almost zero (asymmetry coefficient R=0.05) cycle of extension at 15-20 Hz frequency have been conducted on 5 mm thick disk samples at 20 deg C and - 160 deg C according to the given methods. It is shown that by cyclic crack resistance of welded joint zones of 0Kh18N10T steel and chromium-manganese steels at normal temperature the 07Kh13G20AN4 steel exceeds 0Kh18N10T steel, at low temperature it yields to 0Kh18N10T only by fracture toughness of heat affected zones HAZ and weld metal (ne). 07Kh13G20AN4 steel and its welded joints as most hardened and cheap may be a good substituent for 0Kh18N10T steel. Optimization of WM alloying for increase of its cyclic fracture toughness at cryogenic temperatures is necessary

  10. Influence of structure and properties of tubular billets of the 12 Kh 18N10T steel on deformability of tubes at cold-rolling mills

    International Nuclear Information System (INIS)

    Vil'yams, O.S.; Bol'shova, N.M.; Olejnik, O.V.; Velikotnaya, E.S.

    1979-01-01

    Metallographic analysis of the defects of the ''oblique cracks'' type on the surface of hot-rolled tubes of the 12Kh18N10T steel has been carried out. Recommended is the complex of mechanical properties and the structure factors (grain size) of conversion hot-rolled tubes, providing the combination of ductility and high rapture strength during rolling at pilger mills. At a grain size not coarser than number 5, a billet must have σsub(T) 5 >=40 %. Hot-rolled coarse-grained billet is not recommended for warm rolng because of high strain hardening

  11. Effect of heat treatment and plastic deformation on the structure and the mechanical properties of nitrogen-bearing 04N9Kh2A steel

    Science.gov (United States)

    Blinov, V. M.; Bannykh, O. A.; Lukin, E. I.; Kostina, M. V.; Blinov, E. V.

    2014-11-01

    The effect of the conditions of heat treatment and plastic deformation on the structure and the mechanical properties of low-carbon martensitic nickel steel (9 wt % Ni) with an overequilibrium nitrogen content is studied. The limiting strain to failure of 04N9Kh2A steel is found to be 40% at a rolling temperature of 20°C and 80% at a rolling temperature of 900°C. Significant strengthening of the steel (σ0.2 = 1089 MPa) is obtained after rolling at a reduction of 40% at 20°C. The start and final temperatures of the α → γ transformation on heating and those of the γ → α transformation on cooling are determined by dilatometry. The specific features of the formation of the steel structure have been revealed as functions of the annealing and tempering temperatures. Electron-microscopic studies show that, after quenching from 850°C and tempering at 600°C for 1 h, the structure contains packet martensite with thin interlayers of retained austenite between martensite crystals. The strength of the nitrogen-bearing 04N9Kh2A steel after quenching from 850 and 900°C, cooling in water, and subsequent tempering at 500°C for 1 h is significantly higher than that of carboncontaining 0H9 steel used in cryogenic engineering.

  12. Steel corrosion in tributyl phosphate in the presence of water and ethyl mercaptan

    International Nuclear Information System (INIS)

    Pischik, L.M.; Tsinman, A.I.

    1979-01-01

    Studied is the corrosion of steels St3, 15Kh5M, 08Kh13, 10Kh14G14N4T, 08Kh18G8N2T, 10Kh17N13M2T in TBP, in mixtures of TBP with ethyl mercaptan (EM) and two-phase systems TBP-water and TBP-water-EM at 50-150 deg. In pure TBP St3 corrosion rate is low even at 150 deg. In the presence of water St 3 strongly corrodes at above 50 deg temperature in organic and water layers and also in gas phase. The steel-08Kh18G8N2T at 90 deg in acid TBP is passive and its corrosion rate is lower than 0.01 mm/year. In identical conditions the resistance of stainless steels increases together with chromium content but in TBP with acid number 100 and above at 150 deg all tested steels including steel-10Kh17N13M2T are slightly resistant. Thus, even in absence of corrosion active additions of EM the mixture of TBP-water at higher temperature is agressive in relation not only to carbon steel but also to stainless steels

  13. Theoretical study of [Li(H2O)n]+ and [K(H2O)n]+ (n = 1-4) complexes

    International Nuclear Information System (INIS)

    Wojcik, M.J.; Mains, G.J.; Devlin, J.P.

    1995-01-01

    The geometries, successive binding energies, vibrational frequencies, and infrared intensities are calculated for the [Li(H 2 O) n ] + and [K(H 2 O) n ] + (n = 1-4) complexes. The basis sets used are 6-31G * and LANL1DZ (Los Alamos ECP+DZ) at the SCF and MP2 levels. There is an agreement for calculated structures and frequencies between the MP2/6-31G * and MP2/LANL1DZ basis sets, which indicates that the latter can be used for calculations of water complexes with heavier ions. Our results are in a reasonable agreement with available experimental data and facilitate experimental study of these complexes. 19 refs., 4 figs., 6 tabs

  14. Changes in structure and phase composition of chromium diffusion layer on stainless steels after long annealing

    International Nuclear Information System (INIS)

    Knyazev, E.V.; Voshedchenko, B.M.; Voskresenskij, Yu.A.

    1985-01-01

    A study was made on the effect of elevated temperatures UU and long holdings at heat on structure, phase composition and properties of chromium diffusion layer on austenitic chromium-nickel stainless steels 10Kh18N10TVD, 10Kh15N30M4B, 10Kh11N23T3MR, 10Kh21N28V6M3. The following mechanism of processes taking place in diffusion chromium layer is presented. The steady drop of chromium concentrations is observed after diffusion saturation. Chromium redistribution related with system transformation to more equilibrium state and simultaneous decarburization of steel surfaces takes place in diffusion layers of 10Kh15N30M4B and 10Kh21N28V6M3 steels after annealing at different temperatures and holdings at heat. Decarburization of steel surface layers is practically excluded in diffusion layers of 10Kh18N10T-VD and 10Kh11N23T3MR steels. Diffusion chromium-saturated layer stays effective only on 10Kh18N10T-VD and 10Kh11N23T3MR steels on heating up to 1000 deq C with holding up to 250 h

  15. Quality of austenite chrome-nickel steel made by gas-oxygen refining

    International Nuclear Information System (INIS)

    Fel'dgandler, Eh.G.; Levin, F.L.; Moshkevich, E.A.; Shifrin, Eh.V.; Movshovich, V.S.; Pargamonov, E.A.

    1991-01-01

    Properties and structure were investigated of austenitic 03Kh18N11 and 08KhN10T steels melted at gas oxygen refining aggregates. It was established that mechanical and corrosion properties of rolling of such steels were in agreement with standard properties of metal of open melting. Sheet 08Kh18N10T steel has the level of strength and plasticity regulated for 12Kh18N10T steel. As steel of 08Kh18N10T holds the complex of high mechanical and corrosion properties, 08Kh18N10T is recommended to be replace by 12Kh18N10T with the aim of decrease of titanium usage and increase of process efficiency

  16. Influence of sulphur and phosphorus impurities on ductility of 25Kh2NMFA steel during forging

    International Nuclear Information System (INIS)

    Onishchenko, A.K.

    1989-01-01

    Using cylindrical samples of the 25Kh2NMFA steel with sulfur and phosphorus content in the range of 0.001-0.030%, tensile test with the rate of deformation 10 -3 s -1 at the temperatures of 800-1200 deg C has been conducted. Analysis of fracture foci and plasticity diagrams has shown, that to ensure ductility during forging and high mechanical properties, the content of sulfur and phosphorus impurities in the 25Kh2NMFA steel must not exceed 0.015%

  17. Specific features of precipitation hardening of austenitic steels with various base. 2. Kinetics and mechanism of carbide precipitation

    International Nuclear Information System (INIS)

    Kositsyna, I.I.; Sagaradze, V.V.; Khakimova, O.N.

    1997-01-01

    Electron microscopic studies were carried out to determine the kinetics and mechanisms of precipitation hardening in Fe-Mn, Fe-Mn-Cr, Fe-Cr-Mn-N, Fe-Cr-Ni and Fe-Ni base stainless steels (45G20M2F2, 50Kh16G15N6M2F2, 45Kh18N10G10M2F2, 40Kh18Ni18M2F2, 45N26M2F2). The steels were heat treated under various conditions. It is revealed that in manganese steels the particles of vanadium carbide nucleate according to homogeneous mechanism at all aging temperatures (600-750 deg C). The presence of chromium in the matrix promotes the transition to heterogeneous mechanism of carbide nucleation and growth. With nickel content increasing the plasticity of precipitation hardened steels gets better due to more intense diffusion of atoms and vacancies to grain boundaries and, hence, the widening of near-boundary zones free of carbide particles

  18. Peculiarities of welding procedure for the 05Kh12K14N5M5T-VD maraging stainless steel with strength higher 1500 MPa

    International Nuclear Information System (INIS)

    Pustovit, A.I.

    1980-01-01

    The effect of welding procedure of 05Kh12K14N5M5T-VD stainless steel on the properties of its welded joints is investigated. A new procedure of welding for pressure vessels made of this steel using Sv-03Kh15K14N5M3T-EL welding wire is suggested [ru

  19. Corrosion of chromium, nickel, titanium and steels in solutions of sodium and ammonium thiosulfates

    International Nuclear Information System (INIS)

    Grebenshchikova, S.V.; Kochergin, V.P.; Doronina, I.V.

    1983-01-01

    Results of gravimetric determinatiion of average rate of chromium, nickel, titatnium and steels 12Kh18N10T and VSt.3 corrosion rate in solutions 50 mass.% (NH 4 ) 2 S 2 O 3 and Na 2 S 2 O 3 in the air and nitrogen atmosphere at 333 K have been generalized. Anodic polarization curves are recorded and stationary potentials of metals and steels under the conditions are measured. It is shown that in (NH 4 ) 2 S 2 O 3 solution the rate of metal and steels corrosion is higher than in Na 2 S 2 O 3 solution indepenent of the nature of gaseous medium contacting with solution. In the series Ni → VSt.3 → 12Kh18N10T → VT1 → chromium in (NH 4 ) 2 S 2 O 3 and Na 2 S 2 O 3 solutions at 333 K corrosion resistance increases. Chromium, titanium and chromium-nickel steel 12Kh18N10T possess a high corrosion resistance

  20. Tendency of the 18-8 type corrosion-resistant steel to cracking in automatic building-up of copper and copper base alloys in argon

    International Nuclear Information System (INIS)

    Abramovich, V.R.; Andronik, V.A.

    1978-01-01

    Studied was the tendency of the 18-8 type corrosion-resistant steel to cracking during automatic building-up of copper and bronze in argon. The investigation was carried out on the 0kh18n10t steel in argon. It had been established, that the degree of copper penetration into the steel inceases with the increase in the time of the 0Kh18n10t steel contact with liquid copper. Liquid copper and copper base alloys have a detrimental effect on mechanical properties of the steel under external tensile load during intercontant. It is shown that in building-up of copper base alloys on the steel-0Kh18n10t, tendency of the steel to cracking decreases with increase in stiffness of a surfaced weld metal plate and with decrease in building-up energy per unit length. The causes of macrocracking in steel at building-up non-ferrous metals are explained. The technological procedures to avoid cracking are suggested

  1. Evolution of secondary-phase precipitates during annealing of the 12Kh18N9T steel irradiated with neutrons to a dose of 5 DPA

    Science.gov (United States)

    Tsai, K. V.; Maksimkin, O. P.; Turubarova, L. G.

    2007-03-01

    The formation and evolution of thermally-induced secondary precipitates in an austenitic stainless steel 12Kh18N9T irradiated in the core of a laboratory reactor VVR-K to a dose of 5 dpa and subjected to post-radiation isochronous annealings for 1 h in a temperature range from 450 to 1050°C have been studied using transmission electron microscopy (TEM) and microhardness measurements. It has been shown that the formation of stitch (secondary) titanium carbides and M 23C6 carbides at grain and twin boundaries after annealing at 1050°C is preceded by a complex evolution of fineparticles of secondary phases (titanium carbides and nitrides) precipitated at dislocation loops and dislocations during annealing at temperatures above 750°C.

  2. Estimation of structural strength of 38KhN3MFA steel, melted using different methods

    International Nuclear Information System (INIS)

    Kudrya, A.V.; Mochalov, B.V.; Fadeev, Yu.I.

    1982-01-01

    Quantity of steel melted by different methods using criteria of fracture mechanics is evaluated. Three technological variants of the 38KhN3MFA steel melting: acid Martin steel prepared by the duplex-process (melt 1); the main Martin steel melting with deoxidation and alloying in a ladle by liquid alloy and treatment with synthetic slag with argon purging after production (melt 2) and its electroslag remelt - ESP process (melt 3) are investigated. The analysis of the investigated melts has revealed that crack resistances of the acid Martin steel is higher than that of other melts at practically similar standard mechanical properties with 0.35 probability at 0.05 significance level in the low-tempered state; in the tempered state the best crack resistance is observed in the ESP main Martin steel. Metal of the main Martin melting has lower crack resistance as compared with other meltings at both strength levels. The results of the work point out the necessity of applying the criteria of fracture mechanics for obtaining an objective evaluation of the steel quality

  3. Effect of silicon on the structure, tribological behaviour, and mechanical properties of nitrogen-containing chromium-manganese austenitic steels

    International Nuclear Information System (INIS)

    Korshunov, L.G.; Chernenko, N.L.; Gojkhenberg, Yu.N.

    2003-01-01

    The effect of silicon in quantity of 3.5-4.5 mass. % on tribological behaviour is studied for nitrogen-bearing (0.20-0.52 mass. % of nitrogen) chromium-manganese austenitic steels (10Kh15G23S4A0.20, 10Kh16G17N3S4A0.30, 10Kh19G20NS4A0.50, 12Kh19G19NS2A0.50, 10Kh18G19A0.50, 08Kh16G8N10S4A0.18). Mechanical properties and corrosion resistance of the steels are determined. Using metallographic, x-ray diffraction and electron microscopical methods a study is made into structural transformations running in the steels considered under friction and static tension. It is shown that additional silicon alloying of nitrogen-bearing chromium-manganese austenitic steels results in an essential increase of adhesion wear resistance of the materials on retention of low friction coefficient (f=0.25-0.33). A strong silicon effect on steel tribological behaviour is related with planar slip activation and with an increase of austenite strength and heat resistance [ru

  4. Pipes out of the chromium-molybdenum 12Kh2M1 steel intended for power units

    International Nuclear Information System (INIS)

    Saf'yanov, A.V.; Plyatskovskij, O.A.; Khokhlov-Nekrasov, O.G.; Palatnikova, E.S.; Karpenko, N.P.

    1977-01-01

    Vanadiumless steel 12Kh2M1 (2.25%Cr, 1%Mo) known to be applied abroad has been used for production of 325x60 mm tubes. The technology involves heating of the blanks to 1270-1300 deg C, their piercing in a double-roller mill, rolling on a pilger mill 8-16'' in thick wall caliber rolls, thermal treatment (normalizing at 930-960 deg C for 1 hour and tempering at 730+-10 deg C for 4 hours and etching (12-22% H 2 SO 4 and up to 143 g/l FeSO 4 ) for 3-4 hours at 55-65 deg C. Good technological properties of the steel and its capacity of working at 540-580 deg C are confirmed. Vanadium alloying of boiler steels does not provide for essential improvement of oxydation resistance and long term strength, but decreases the workability and enhances scatter of working parameters on account of minor variations of chemical composition

  5. Heat treatment effect on impact strength of 40Kh steel

    International Nuclear Information System (INIS)

    Golubev, V.K.; Novikov, S.A.; Sobolev, Yu.S.; Yukina, N.A.

    1984-01-01

    The paper presents results of studies on the effect of heat treatment on strength and pattern of 40Kh steel impact failure. Loading levels corresponding to macroscopic spalling microdamage initiation in the material are determined for three initial states. Metallographic study on the spalling failure pattern for 40Kh steel in different initial states and data on microhardness measurement are presented

  6. Study of 16KhSN high strength steel in different structural states and under working conditions

    International Nuclear Information System (INIS)

    Skudnov, V.A.; Vorob'ev, I.A.; Kutyajkin, V.G.; Bugrov, Yu.V.

    1985-01-01

    A study was made on the effect of deformation degree (up to 60%) during reducing, drawing and heat treatment (annealing at 750 deg C), quenching from 930 deg C and tempering at 350 deg C) on strength, plasticity, hardening degree, notch sensitivity, density and elasticity characteristics of the steel. The effect of test temperature (from-196 up to 1000 deg C) on tensile strength and plasticity was studied as well. It was established that drawing and reducing of 16KhSN steel in annealed state with strain degrees of up to 60% results to increase of strength characteristics 1.7...2.3 times and decrease of plasticity characteristics by 15...23%, strain hardening coefficient - 2.2 times and the maximum strain energy - by 80 MJ/m 3 . Hardening heat treatment (quenching from 930 deg C+temperating at 350 deg C) affects on mechanical properties of 16KhSN steel in much the same way as cold working, but strength characteristics of heat-treated steel increase 2.6...3.6 times and the maximum strain energy grows by 640 MJ/m 3 . Systematic data on the effect of temperature (-196...1000 deg C) and tensile rate (4 mm/min...5m/s) on strength and plasticity of 16KhSN steel in annealed state were obtained

  7. Coarsening of (Fe, Cr)23C6 carbide phase on the tempering of 14Kh17N2 chromium-nickel steel

    International Nuclear Information System (INIS)

    Psarev, V.I.

    2002-01-01

    Paper lists the results of computer analysis of distribution according to sizes (Fe, Cr) 23 C 6 microparticles resulting from 14Kh17N2 steel tempering under 700 Deg C. Data were obtained at the maximum beneficial magnification of a light microscope. The mentioned curves of distribution densities are characterized by more reliable run from most permissible sizes of dispersed particles. Application of general rules of distributions and of previously elaborated procedure to identify experimental histograms with theoretical distributions enables to derive valuable information on dynamics of coarsening of a disperse phase in this case, as well [ru

  8. Effect of preliminary heat treatment on phase transformations and properties of the Kh15N5D2T (VNS-2) steel

    International Nuclear Information System (INIS)

    Madyanov, S.A.; Voronenko, B.I.; Makhnev, E.S.

    1978-01-01

    It is shown that preliminary heat treatment has a significant effect on the α→γ transformation kinetics, the quantity of residual austenite, the grain size and mechanical properties of the Kh15N5D2T steel after final heat treatment. The preliminary heat treatment regimes leading to the increase of the quantity of residual austenite and to grain refining increase the work of crack propagation in the finally strengthened state. The optimum properties were obtained after threefold preliminary tempering for 1h at 650 deg C. An approximately constant relation of α- and γ-phases (approximately 50%) is observed at 625 deg C irrespective of the investigated regimes of preliminary heat treatment

  9. Effect of nonmetallic inclusions on anisotropy of ductility in 35KhN3MFA steel forgings

    International Nuclear Information System (INIS)

    Shtremel', M.A.; Yavojskij, V.I.; Volkov, V.A.; Chursin, G.M.; Chukhlov, V.I.; Fetisov, G.I.; Mochalin, N.K.; Smol'yaninov, L.V.

    1980-01-01

    Characteristics of nonmetaltic inclusions and anizotropy of ductility and of impuct strength of forgings of the 35KhN3MFA steel are compared at different variants of melting and outer-furnace treatment. It is shown that method of melting rugulates anisotropy of ductility primarily through deformability of large inclusions during forging. Deformability of inclusions considerably changes due to introduction of silicocalcium in iron mold [ru

  10. Successive carbon- and boron saturation of KhVG steel in powder mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Alimov, Yu A; Gordienko, S I

    1975-01-01

    Method of successive saturation of KhVG steel with carbon and boron in powder mixtures is described. After carbonization of steel in a charcoal carburator at 930 deg C during 3 hrs a domain of equiaxial large grains is formed there the latter representing carbides of Fe/sub 3/C and (Fe, M)/sub 3/C. The increase of duration of carbonization up to 5 hrs and above results in formation of a cement grid greatly impairing the mechanical properties of the metal. Carbonization is followed by borating in powdered technical boron carbide at 900 deg C for 4 hrs which ensures formation on the sample surface of a borated layer with depth up to 65 mkm covering the carbonized zone. As followed from metallographic and x-ray structural analysis, the borated layer consists of boride needles with complex composition (Fe, Cr, Mn)B. Oil hardening of carbonized KhVG steel from 850 deg C and low-temperature tempering at 180 deg C for 1 hr results in formation in the main metal of martensite-carbide structure and, respectively, in the decrease of the microhardness gradient between the diffusion layers, as compared with borated KhVG steel. Operation tests of strengthened matrices of preforming machines under the conditions of application of dynamic pressing forces up to 1500 kg Fce/cm/sup 2/ demonstrated that the cyclical strength of carboborated coverings is 2.0-3.0 times higher than that of borated ones. The method of carboborating is recommended for strengthening the details of stamp and press tools.

  11. [Effect of KH2PO4 on the odonto- and osteogenic differentiation potential of human stem cells from apical papillae].

    Science.gov (United States)

    Wang, Yan-ping; Wu, Jin-tao; Wang, Zi-lu; Zheng, Yang-yu; Zhang, Guang-dong; Yu, Jin-hua

    2013-01-01

    To determine the effects of KH2PO4 on the odonto- and osteogenic differentiation potential of human stem cells from apical papillae (SCAP) in vitro. SCAP were isolated and cultured respectively in alpha minimum essential medium (α-MEM) or α-MEM containing 1.8 mmol/L KH2PO4. Alkaline phosphatase (ALP) activity, alizarin red staining, real-time reverse transcription polymerase chain reaction (RT-PCR) and Western blotting were used to examine the odonto and osteogenic potential of SCAP in the two media. SCAP cultured in α-MEM containing 1.8 mmol/L KH2PO4 exhibited a higher ALP activity [(0.370 ± 0.013) Sigma unit×min(-1)×mg(-1)] at day 3 than control group [(0.285 ± 0.008) Sigma unit×min(-1)×mg(-1)] and KH2PO4-treated SCAP formed more calcified nodules at day 5 [(0.539 ± 0.007) µg/g] and day 7 [(1.617 ± 0.042) µg/g] than those in normal medium [(0.138 ± 0.037) µg/g, P odonto- and osteogenic markers were significantly up-regulated after the stimulation of KH2PO4 at day 3 and 7 respectively, as compared with control group. 1.8 mmol/L KH2PO4 can promote the odonto and osteogenic differentiation potential of human SCAP.

  12. Corrosion of austenitic steels and their components in vanadium-containing chloride melts

    Science.gov (United States)

    Abramov, A. V.; Polovov, I. B.; Rebrin, O. I.; Lisienko, D. G.

    2014-08-01

    The corrosion of austenitic 12Kh18N10T, 10Kh17N13M2T, and 03Kh17N14M3 steels and their components (Cr, Fe, Ni, Mo) in NaCl-KCl-VCl2 melts with 5 wt % V at 750°C is studied. The rates and mechanisms of corrosion of the materials under these conditions are determined. The processes that occur during contact of the metals and steels with vanadium-containing chloride electrolytes are investigated.

  13. KH 2PO4 as a novel catalyst for regioselective monobromination of aralkyl ketones using N-bromosuccinimide: a green methodology

    Directory of Open Access Journals (Sweden)

    P. Md. Khaja Mohinuddin

    2015-08-01

    Full Text Available A simple, regioselective and green method has been developed for the preparation of monobrominated ketones from various aralkyl ketones by using N-bromosuccinimide in presence of KH 2PO 4 in EtOH at reflux temperature. The present method is of short reaction time and simple with excellent isolated yields of products. The use of eco-friendly solvent, reuse of organic waste (succinimide and recyclable catalyst used for 4 times without loss of activity are advantageous. This is the first example of the use of KH 2PO 4 as a useful catalyst in organohalogen chemistry and the present method meets reduce-reuse-recycle (RRR principle towards development of green protocol.

  14. The effect of thermoplastic treatment regimes on the microplastic strain of nitrogen-containing steel Kh21G10N7MBF

    International Nuclear Information System (INIS)

    Bannykh, O.A.; Blinov, V.M.; Kostina, M.V.; Grachev, S.V.; Mal'tseva, L.A.

    2005-01-01

    A study is made into the influence of a percentage reduction during cold rolling and subsequent holdings at heat on development of microplastic deformation when bending sheet specimens of stainless austenitic high-nitrogen steel Kh21G10N7MBF. It is revealed that a maximum value of apparent limit of elasticity (∼1800 MPa) is attained due to plastic deformation by rolling at 20 Deg C with a total percentage reduction of 60 % and subsequent aging at 500 Deg C for 1-4 h [ru

  15. Corrosion cracking of 03N18K1M3TYu and 02N12Kh5M3 maraging steels in chloride solutions

    Energy Technology Data Exchange (ETDEWEB)

    Pavlov, V.N.; Chumalo, G.V.; Vereshchagin, A.N.; Melekhov, R.K.

    1987-07-01

    The authors investigate the electrochemical behavior in 0.5% NaCl solution and 42% MgCl/sub 2/ solution and the tendency toward corrosion cracking was determined in boiling 0.5% chloride solution of the cobalt-containing maraging steels in the title. Weld specimens and specimens of the base metal of 03N18K1M3TYu steel were tested in 3% NaCl solution for resistance to corrosion cracking. Additional investigations were made of specimens of that steel with previously created fatigue cracks of the base metal and the weld specimens in 3% NaCl solutions, since that steel is a promising material for structures operating in sea water and low concentration chloride solutions.

  16. Effect of Cr, Ni, and Mo additions on the susceptibility of the 0Kh6n7m7c steel to hot cracking

    International Nuclear Information System (INIS)

    Tolstykh, L.G.; Pryakhin, A.V.; Popov, A.N.; Usynin, V.F.

    1977-01-01

    The effect of chromium, molybdenum, and nickel on the tendency of surfacing materials to form hot cracks (Vsub(kp) was studied using the mathematical statistics method. The St3 steel and 38KhN3MFA steel were used in the study. A device facilitating the hot cracking tendency test procedure was developed. It was found that, in the concentration range involved, Ni and Mo produce no effect on Vsub(kp), and Cr enhances it. A new powder wire, PP-OKh7N8M6S, capable of increasing surface material resistance by 1.5-2 times, has been developed

  17. Strain ageing of the 15Kh2MFA steel at 500 and 550 deg C

    International Nuclear Information System (INIS)

    Maksimovich, G.G.; Azbukin, V.G.; Krylova, R.P.; Tretyak, I.Yu.; Bardachevskaya, T.V.

    1978-01-01

    The effect of ageing at high temperatures and under high stresses on strength and plasticity of the 15Kh2MFA steel has been studied. The steel was kept at 500 and at 550 deg C for 100, 1000 and 2500 hours without stress and under stress of 0.5 and 0.9 of the long-term strength limit (sigmasub(ls)). Ageing at 500 deg C without stress and under 0.5 sigmasub(ls) changed neither strength nor plasticity of the steel; under 0.9 sigmasub(ls) the strength somewhat decreased. Ageing at 550 deg C for 1000 hours resulted in an appreciable stress drop

  18. Corrosion behaviour of stainless steels by internal friction method

    International Nuclear Information System (INIS)

    Postnikov, V.S.; Kovalevskij, V.I.

    1987-01-01

    Corrosion of austenite chromium-nickel stainless steels 12 Kh18N9, 12Kh18N9T, 12Kh18N10 and 12Kh18N10T is investigated. Wire samples 0.7...0.8 mm in diameter before tests were subjected to quenching in water from the temperature of 1050...1100 deg C and part of them - to tempering at 650 deg C for 2 h. Pitting corrosion was brought about by different concentration of iron chloride solutions (C FeCl 3 ). Total corrosion has a slight effect on the character of IF (internal friction) variation that increases without the whole test period up to the moment when mechanical strength of the sample

  19. Effect of hydrostatic pressure on phase transformations in Kh17N8 steel during deformation

    International Nuclear Information System (INIS)

    Eshchenko, R.N.; Teplov, V.A.

    1984-01-01

    The phase composition and structure of Kh17N8 steel strained to different degrees under atmospheric pressure and 1700 MPa are investigated. It has been found that deformation at 1700 MPa causes α and epsilon-martensite formation, the same deformation under atmospheric pressure - only α-martensite formation. The amount of the formed α-martensite is not changed with application of hydrostatic pressure. Electron-microscopic observations have shown that the dispersion of α-martensite formed under pressure is higher than in the absence of pressure; no interconnection in formation of α and epsilon-martensite in samples strained under pressure has been observed

  20. Structure, mechanical and corrosion properties of powdered stainless steel Kh13

    International Nuclear Information System (INIS)

    Radomysel'skij, I.D.; Napara-Volgina, S.G.; Orlova, L.N.; Apininskaya, L.M.

    1982-01-01

    Structure, mechanical and corrosion properties are studied for compact powdered stainless steel, Grade Kh13, produced from prealloyed powder and a mixture of chromium and iron powders by hot vacuum pressing (HVP) following four schemes: HVP of unsintered billets; HVP of presintered billets; HVP of unsintered billets followed by diffusion annealing; HVP of sintered billets followed by diffusion annealing. Analysis of the structure, mechanical and corrosion properties of Kh13 steel produced according to the four schemes confirmed that production of this steel by the HVP method without presintering of porous billets and diffusion annealing of compact stampings is possible only when prealloyed powder of particular composition is used as a starting material

  1. Corrosion behavior of austenitic steels and their components in niobium-containing chloride melts

    Science.gov (United States)

    Abramov, A. V.; Polovov, I. B.; Rebrin, O. I.; Volkovich, V. A.; Lisienko, D. G.

    2014-02-01

    The mechanism of corrosion of austenitic steels 12Kh18N10T, 10Kh17N13M2T, and 03Kh17N14M3 and metals Cr, Fe, Ni, and Mo in a NaCl-KCl-NbCl n ( n = 3.5, Nb content is 5 ± 0.1 wt %) melt at 750°C is studied. The metal and steel corrosion rates under these conditions are determined. The character of material fracture and the mechanisms of material corrosion are found.

  2. Effect of helium ion bombardment on hydrogen behaviour in stainless steel

    International Nuclear Information System (INIS)

    Guseva, M.I.; Stolyarova, V.G.; Gorbatov, E.A.

    1987-01-01

    The effect of helium ion bombardment on hydrogen behaviour in 12Kh18N10T stainless steel is investigated. Helium and hydrogen ion bombardment was conducted in the ILU-3 ion accelerator; the fluence and energy made up 10 16 -5x10 17 cm -2 , 30 keV and 10 16 -5x10 18 cm -2 , 10 keV respectively. The method of recoil nuclei was used for determination of helium and hydrogen content. Successive implantation of helium and hydrogen ions into 12Kh18N10T stainless steel results in hydrogen capture by defects formed by helium ions

  3. Local corrosion of high alloy steels under biodeposits

    International Nuclear Information System (INIS)

    Korovyakova, M.D.; Nikitin, V.M.; Speshneva, N.V.

    1999-01-01

    Impact of the bacteriozenosis different structural-functional state under biodeposits on corrosion resistance of the 12Kh18N10T and Kh18N10T high-alloy steels in the natural seawater is studied. It is shown that saturation of natural micro communities by separate aerobic and facultative-anaerobic bacterial monocultures increases corrosion resistance of these steels by their overgrow with biodeposits [ru

  4. Effect of Heat Treatment on the Structure and Properties of Die Steel 70Kh3G2FTR

    Science.gov (United States)

    Krylova, S. E.; Kletsova, O. A.; Gryzunov, V. I.; Fot, A. P.; Tavtilov, I. Sh.

    2018-01-01

    The effect of heat treatment parameters on the properties and structural and phase composition of a promising die steel 70Kh3G2FTR for hot deformation is studied. The temperature-and-stress state of a hammer die under a heat treatment is simulated.

  5. Effect of smelt aluminium on mechanical properties of steels

    International Nuclear Information System (INIS)

    Ryabov, V.R.; Dykhno, I.S.; Deev, G.F.; Karikh, V.V.

    1987-01-01

    Effect of smelt aluminium on mechanical properties of armco-iron and 12 Kh18N10T steel is studied. It is stated that in smelt aluminium and aluminium alloy contact with armco-iron the sample ductility is decreased. Corrosion effect of smelt alluminium on (18Kh15N5AM3) steel in the form of reinforced wire in aluminium-steel KAS-1A composite material is investigted. It is stated in experiment that during smelt alluminium-steel contact interaction of heterogeneous phases takes place

  6. Preliminary tension effect on low-cycle fatigue of 40Kh13 steel in gaseous hydrogen

    International Nuclear Information System (INIS)

    Romaniv, A.N.

    1984-01-01

    Comparative bending tests of specimens deformed by tension at 65, 18 and 30% in hydrogen and vacuum were accomplished to reveal the effect of preliminary tension on low-cycle fatigue strength of 40Kh13 martensitic steel. It was found that small amounts of preliminary strains induced a considerable decrease in low-cycle durability in vacuum and hydrogen which was connected with developing defects arising at the early stages of plastic deformation. A rather high degree of preliminary tension promoted steel homogenization, hydrogen embrittlement decrease and service behaviour improvement

  7. Effect of nickel and MnS inclusions in the metal on the pitting corrosion of low-carbon stainless steels

    International Nuclear Information System (INIS)

    Frejman, L.I.; Nguen, The Dong; Volkov, D.E.; Konnov, Yu.P.

    1986-01-01

    The resistance to pitting corrosion of steels on the 03Kh17-03Kh18 base containing up to 20 % Ni at different levels of S and Mn impurities contamination is investigated. It is shown that up to 50 % of nickel introduced into ordinary steels with 5-6 % Ni is spent to compensate the resistance decrease caused by MnS inclusions. Full compensation is not attained even in the 10-20 %. Ni range in which nickel practically does not affect the resistance of neither ordinary, nor pure (without MnS) steels. Titanium introduction into ordinary steel on the Kh22N6 base permits to surpass the level of 03Kh17N3 pure steel resistance and attain the level of 03Kh17N6 pure steel almost by all characteristics (including passivated characteristics in sulfuric acid) besides pitting repassivity. In this property pure steels with Ni >or approx. 3 % surpass even the molybdenum containing 03Kh21NbM2T ordinary steel though they by far concede by passivation in sulfuric acid

  8. Cyclic crack resistance of anticorrosion cladding-15Kh2MFA steel joint

    International Nuclear Information System (INIS)

    Zvezdin, Yu.I.; Nikiforchin, G.N.; Timofeev, B.T.; Zima, Yu.V.; Andrusiv, B.N.

    1985-01-01

    Cyclie crack resistance of transition zone in austenitic cladding steel 15Kh2MFA joint is studied, taking into account the geometry of fatigue cracks, fracture micromechanism and crack closure effect. Kinetics of crack development from the cladding to the basic metal and vice versa is considered. Microstructure of transition zone is investigated. The results obtained are considered as applied to WWER. It is emphasized, that the braking of fatigue cracks is observed at low asymmetry of loading cycle. Increased loading asymmetry accelerates sharply the alloy fracture due to the growth of subcladding crack, at that, the direction of crack propagation and the structure of transition zone are not of great importance

  9. Structural inheritance in cast 30KhGNM-type steel

    International Nuclear Information System (INIS)

    Sadovskij, V.D.; Bershtejn, L.I.; Mel'nikova, A.A.; Polyakova, A.M.; Schastlivtsev, V.M.

    1980-01-01

    Structural inheritance in the cast 30KhGNM-type steel depending on the heating rate and the temperature of preliminary tempering is investigated. When eating the cast steel with a beinite structure at the rate of 1-150 deg/min, the restoration of austenite grain and the following recrystallization due to the phase cold work, are observed. Slow heating from room temperature or preliminary tempering hinder grain restoration during heating. A non-monotonous effect of tempering temperature on the structural inheritance is established which can be connected with the kinetics of decomposition of residual austenite in steel

  10. Effect of heat treatment regime on structural lamination in ferritic-austenitic steels

    International Nuclear Information System (INIS)

    Sizov, R.A.; Zakharova, M.I.; Novikov, I.I.; Bannykh, O.A.

    1983-01-01

    The effect of preliminary thermal treatment on lamination and viscosity of EhP-53 and KO-3 steels after durable aging at the temperature of 350 is studied. It is shown that preliminary heat treatment considerably affects lamination processes in the result of aging of 0Kh18G8N2T steel. The lowest rate of lamination and higher impact strength after aging at 350 deg C for 4500 hours corresponds to the following heat treatment: 10 hour aging at 650 deg C with cooling in the air, then quenching in water from 950 deg C after aging for 30 min and the following tempering (650 deg C, 5 hours). Unlike the 0Kh18G8N2T steel, lamination parameters of steel 0Kh22N6T practically do not change after the application of heat treatment. Nevertherless, taking into account results of impact strength, it is advisable to have thermal treatment according to the regime: quenching in water at 950 deg C after aging for 30 min

  11. Chromium surface alloying of structural steels during laser treatment

    International Nuclear Information System (INIS)

    Kurov, I.E.; Nagornykh, S.N.; Sivukhin, G.A.; Solenov, S.V.

    1987-01-01

    Results of matrix alloying from the surface layer and creation of considerably increased chromium concentration in the depth which permits to increase the efficiency of laser treatment of steels (12Kh18N10T and 38KhN3M) in the process of their further mechanical polishing, are presented. The treatment was realized by continuous CO 2 -laser at different power densities and scanning rates are presented. A model describing the creation of anomalous distributions of the alloying element in steels is plotted

  12. Optimal control of conditions of deformation during rolling the bar alloy from alloy steel

    International Nuclear Information System (INIS)

    Inatovich, Yu.V.; Shilov, V.A.; Shvarts, D.L.; Kudelin, S.P.

    2001-01-01

    A complex of programs for determining the optimal gaps between rollers during rolling of simple merchant sections of alloy steels of a wide brand assortment (12KhN3A, Kh17N2, Kh18N10T) was elaborated. Experience in calculations made according to the programs suggests advisability of their use in the automated design systems for roller calibration and for adjustment of section mills [ru

  13. Stationary potentials and corrosion of metals and steels in sodium and potassium chloride eutectic melts saturated with hydrogen chloride

    International Nuclear Information System (INIS)

    Belov, V.N.; Ershova, T.K.; Kochergin, V.P.

    1978-01-01

    Stationary potentials have been measured at 850 deg C and corrosion rates found gravimetrically for a number of metals and steels in the eutectic NaCl-KCl melt saturated with HCl. Periodic shifts of the stationary potentials towards positive values have been established in the Ti-V-Cr-Fe-Ni, Cu-Zr-Nb-Mo, Ag-Ta-W-Pt systems, with the corrosion rate of metals decreasing in them. The stationary potentials are shown to shift towards positive values in the series: st.08 KP, st.3, Kh17N2, Kh22N6T, Kh13NChG9, 1Kh18N10T, Kh17N13M2T, OKh17N16M3T, Kh23N18, Kh25N16G7, Kh23N28M3D3T, with corrosive resistance in this series increasing

  14. The influence of heating rate on reheat-cracking in a commercial 2 1/4Cr1Mo steel

    International Nuclear Information System (INIS)

    Hippsley, C.A.

    1983-03-01

    The effects of elevated heating rate on stress-relief cracking in a commercial 2 1/4 Cr1Mo steel have been investigated. A SEN bend-specimen stress-relaxation test was used to assess reheat cracking susceptibility and fracture mechanisms for an initial post-weld heating rate of 1000 Kh - 1 . Two factors controlling the influence of heating rate on the final severity of cracking were identified, i.e. the rate of stress-relaxation with respect to temperature, and the time available for crack-growth. The factors were found to counteract each other, but in the case of commercial 2 1/4 Cr1Mo steel, the crack-growth factor outweighed the relaxation factor, resulting in a reduction in the propensity to stress-relief cracking at the elevated heating rate. However, by reference to the results of a separate investigation concerning A508/2 MnMoNiCr steel it was demonstrated that the balance between these two factors may be reversed in other alloy systems, with the consequence that reheat cracking is exacerbated by increasing the initial heating rate. A computer model was addressed to the stress-relaxation test conditions using data from the commercial 2 1/4 Cr1Mo steel. The model predictions exhibited reasonable agreement with experimental test results for both 100 Kh - 1 and 1000 Kh - 1 heating rates. (author)

  15. The Kinetics of Bainitic Transformation of Roll Steel 75Kh3MF

    Science.gov (United States)

    Kletsova, O. A.; Krylova, S. E.; Priymak, E. Yu.; Gryzunov, V. I.; Kamantsev, S. V.

    2018-01-01

    The critical points of steel 75Kh3MF and the temperature of the start of martensitic transformation are determined by a dilatometric method. The thermokinetic and isothermal diagrams of decomposition of supercooled austenite are plotted. The microstructure and microhardness of steel specimens cooled at different rates are studied. The kinetics of the occurrence of bainitic transformation in the steel is calculated using the Austin-Ricket equation.

  16. Electroplastic drawing of stainless steels

    International Nuclear Information System (INIS)

    Troitskij, O.A.; Spitsyn, V.I.; Sokolov, N.V.; Ryzhkov, V.G.

    1977-01-01

    Effect of electroplastic drawing on mechanical, magnetic and electrical properties of wire of 12Kh18N10T and Kh13N13M2 steels was studied. Pulse, direct and alternating currents were used. Direct and alternating current densities were 400 A/mm 2 , mean density of pulse current was 200 A/mm 2 . The investigations have shown that the current density increase results in decreasing the wire strengthening intensity though in increasing plastic properties. As a result of electroplastic drawing the growth of magnetic characteristics of wire occurs

  17. Study of cast and thermo-mechanically strengthened chromium-nickel nitrogen-containing steel

    International Nuclear Information System (INIS)

    Prokoshkina, V.G.; Kaputkina, L.M.; Svyazhin, A.G.

    2000-01-01

    The effect of nitrogen on the structure and strength of corrosion-resistant chromium-nickel steels after thermal and thermomechanical treatment is studied. The 06Kh15N7AD and 07Kh15N7DAMB steels alloying by nitrogen was accomplished through the basic composition steels remelting in the molecular nitrogen atmosphere under the pressure of 0.1-2.5 MPa. The 02Kh15N5DAF and 05Kh15N5DAM steels ingots were obtained through melting in a plasma furnace under the nitrogen pressure of 0.4MPA. The high-temperature thermomechanical treatment (HTMT) was performed by rolling with preliminary blanks heating up to 1050 deg C and the rolling end temperature not below 950 deg C. It is shown, that the HTMT of the nitrogen-containing steels makes it possible to obtain strength characteristics by 1.5 times exceeding the properties of traditionally applicable corrosion-resistant steels, whereby sufficiently high plasticity of the nitrogen-containing steel is retained [ru

  18. Effect of boron control of environment on corrosion and resistance to low-cycle corrosion fatigue in structural steels

    International Nuclear Information System (INIS)

    Babej, Yu.I.; Zhitkov, V.V.; Zvezdin, Yu.I.; Liskevich, I.Yu.; Nazarov, A.A.

    1982-01-01

    Tests of the specimens on total, contact and crevice corrosion, corrosion cracking and low-cycle fatigue are conducted for determination of corrosion and corrosion-fatigue characteristics in the 15Kh3NMFA, 10N3MFA, 10Kh16N4B, 05Kh13N6M2 structural steels, used in energetics. The environment is subjected to boron control and contacting with atmosphere for simulation of stop and operation modes of the facility. The experiments are carried out in the distilled water with 12g/l H 3 BO 3 and 10 mg/l Cl' at 25, 60, 100 deg C under contacting with atmosphere. It is established, that the pearlitic steels 15Kh3NMFA, 10N3MFA, as well as transition and martensitic 05Kh13N6M2 and 10Kh16N4B steels are highly stable to total, crevice and contact corrosion at the high parameters of aqueous boron-containing medium. Steel resistance to low-cycle fracture decreases slightly under the conditions similar to the operation ones, in the water with 12 g/l H 3 BO 3 . Durability of the pearlitic steels at the simulation of stop conditions decreases more noticeably, crack formation as a rule, initiating from corrosion spots

  19. Superheat effect on bainite steel hardenability

    International Nuclear Information System (INIS)

    Kubachek, V.V.; Sklyuev, P.V.

    1978-01-01

    The bainite hardenability of 34KhN1M and 35 KhN1M2Ph steels has been investigated by the end-face hardening technique. It is established that, as the temperature of austenitization rises from 900 to 1280 deg C, the temperature of bainite transformation increases and bainite hardenability of the steels falls off. A repeated slow heating to 900 deg C of previously overheated 34KhN1M steel breaks up grain, lowers the temperature of the bainite transformation and raises the hardenability to values obtained with ordinary hardening from 900 deg C. A similar heating of previously overheated 35KhN1M2Ph steel is accompanied by restoration of initial coarse grains and maintenance of both the elevated bainite transformation temperature and to lower hardenability corresponding to hardening from the temperature of previous overheating

  20. Effect of zirconium on the structure and phase composition of steel 03Kh8SYu

    International Nuclear Information System (INIS)

    Tarzhumanova, V.A.; Ryabchenkov, A.V.; Shatunova, A.V.; Yoganova, S.A.

    1986-01-01

    Previously, the authors determined the optimum zirconium content providing retention of a fine-grained structure for steel 03Kh8SYu during high-temperature heating. It was suggested that this was caused by separation in the steel of intermetallic phase Fe 3 Zr. This paper presents results of further studies in this direction. X-ray analysis results for the anodic residues of the steels are presented. It can be seen that in steel without zirconium, carbides of the type M 23 C 6 and M 7 C 3 and aluminum nitride are present. On adding 0.05% Zr, zirconium nitride forms in addition to the existing aluminum nitride and carbides of the type M 7 C 3 . The authors also investigated the effect of zirconium on the tendency of the steel toward grain growth at higher temperature; they studied the structure of steel 03Kh8SYu with 0.61% Zr after soaking specimens for 100 h at 950-1100 C. Results are presented

  1. Influence of ion implanted helium on deuterium trapping in Kh18N10T stainless steel

    International Nuclear Information System (INIS)

    Tolstolutskaya, G.D.; Ruzhitskij, V.V.; Kopanets, I.E.

    2004-01-01

    The results are presented on evolution of distribution profiles and helium and deuterium thermal desorption ion implanted in steel 18Cr10NiTi. Accumulation, trapping, retention and microstructure evolution are studied; effect helium and hydrogen simultaneous implantation on these processes is also studied

  2. Hydrogen effect on mechanical properties and flake formation in the 10KhSND steel rolled plates

    Energy Technology Data Exchange (ETDEWEB)

    Muradova, R G; Zakharov, V A; Kuzin, A P; Gol' tsov, V A; Podgajskij, M S [Donetskij Politekhnicheskij Inst. (Ukrainian SSR); Donetskij Nauchno-Issledovatel' skij Inst. Chernoj Metallurgii (Ukrainian SSR))

    1982-01-01

    The effect of hydrogen on mechanical properties of the 10KhSND steel rolled plates during natural aging is studied. Optimum period of metal acceptance tests, which are advisable to conduct after 5-7 day natural aging of finished products, are found out. The technique is worked out and a safe hydrogen content to prevent flake formation in the 10KhSND steel is determined. It is shown that a safe hydrogen content is dependent on the experiment conditions (sample dimensions, conditions of cooling, and prehistory).

  3. Hydrogen effect on mechanical properties and flake formation in the 10KhSND steel rolled plates

    International Nuclear Information System (INIS)

    Muradova, R.G.; Zakharov, V.A.; Kuzin, A.P.; Gol'tsov, V.A.; Podgajskij, M.S.

    1982-01-01

    The effect of hydrogen on mechanical properties of the 10KhSND steel rolled plates during natural aging is studied. Optimum period of metal acceptance tests, which are advisable to conduct after 5-7 day natural aging of finished products, are found out. The technique is worked out and a safe hydrogen content to prevent flake formation in the 10KhSND steel is determined. It is shown that a safe hydrogen content is dependent on the experiment conditions (sample dimensions, conditions of cooling, and prehistory)

  4. Protective effect of KhOSP-10 inhibitor during corrosion, hydrogenadsorption and corrosion cracking of a steel in sulfuric acid

    Energy Technology Data Exchange (ETDEWEB)

    Mindyuk, A K; Svist, E I; Savitskaya, O P; Goyan, E B; Gopanenko, A N [AN Ukrainskoj SSR, Lvov. Fiziko-Mekhanicheskij Inst.

    1975-01-01

    The protective propeties of inhibitor KhOSP-10 in the time of corrosion and corrosive cracking of steel 40Kh are higher then those of inhibitors KPI-1, KI-1, I-I-V etc. Its ability to reduce steel hydrogenation is the same as in the case of KPI-1 inhibitor i.e. below that of KI-1. HCl additives enhance the efficiency of inhibitors KPI-1, KI-1, I-1-V etc. up to the protective ability of KhOSP-10. Kinetics of the electrode processes was estimated from polarization curves.

  5. Cooling rate and microstructure of surface layers of 5KhNM steel, machined by electroerosion method

    International Nuclear Information System (INIS)

    Foteev, N.K.; Ploshkin, V.V.; Lyakishev, V.A.; Shirokov, S.V.

    1982-01-01

    The cooling rate and microstructure of surface layers of steel 5KhNM machined by electroerosion method have been studied. It is shown that the difference in heating rate of the surface layers with electric discharge over the 5KhNM steel samples depth results in the intensive size reduction of the microstructure. In the surface layer alongside with martensite residual austenite is present, the lattice period of which increases with the increase of pulse duration, carbide phase of complex composition appears, and concentrational heterogeneity in alloying elements (except carbon) is absent

  6. Cooling rate and microstructure of surface layers of 5KhNM steel, machined by electroerosion method

    Energy Technology Data Exchange (ETDEWEB)

    Foteev, N.K.; Ploshkin, V.V.; Lyakishev, V.A.; Shirokov, S.V.

    1982-01-01

    The cooling rate and microstructure of surface layers of steel 5KhNM machined by electroerosion method have been studied. It is shown that the difference in heating rate of the surface layers with electric discharge over the 5KhNM steel samples depth results in the intensive size reduction of the microstructure. In the surface layer alongside with martensite residual austenite is present, the lattice period of which increases with the increase of pulse duration, carbide phase of complex composition appears, and concentrational heterogeneity in alloying elements (except carbon) is absent.

  7. Using the ''Epiquant'' automatic analyzer for quantitative estimation of grain size

    Energy Technology Data Exchange (ETDEWEB)

    Tsivirko, E I; Ulitenko, A N; Stetsenko, I A; Burova, N M [Zaporozhskij Mashinostroitel' nyj Inst. (Ukrainian SSR)

    1979-01-01

    Application possibility of the ''Epiquant'' automatic analyzer to estimate qualitatively austenite grain in the 18Kh2N4VA steel has been investigated. Austenite grain has been clarified using the methods of cementation, oxidation and etching of the grain boundaries. Average linear size of grain at the length of 15 mm has been determined according to the total length of grain intersection line and the number of intersections at the boundaries. It is shown that the ''Epiquant'' analyzer ensures quantitative estimation of austenite grain size with relative error of 2-4 %.

  8. Nitrogen effect on the tendency of Cr-Ni-MN steels to delayed fracture under stress and hydrogen effects

    International Nuclear Information System (INIS)

    Suvorova, S.O.; Fillipov, G.A.

    1996-01-01

    Austenitic steels types 03Kh17N16G10AM5, 03Kh6N12G10AM5 and 07Kh13AG20 with various nitrogen contents were studied for their tendency to delayed fracture using mechanical tests, fractography and X ray diffraction analysis. The steel type 07Kh13G20 exhibited the highest strength in the initial state but showed an increase tendency to delayed fracture after hydrogenation. It is underlined that nitrogen additions essentially intensify the tendency of cold worked steels to delayed fracture. This fact should be taken into account when using nitrogen-containing Cr-Ni-Mn steels under severe operational conditions. 4 refs., 2 tabs

  9. Influence of heating temperature on bainite transformation proceeding in chromium-nickel-molybdenum steels

    International Nuclear Information System (INIS)

    Kaletin, Yu.M.; Kaletin, A.Yu.

    1983-01-01

    The purpose of the present paper is to investigate the effect of heating and cooling from austenization temperature on development of bainite transformation in 37KhN3MFA and 18Kh2N4MA structural alloyed steels. The metallographical analysis of specimens has revealed that first crystals of bainite under slow heating up to 770-790 deg C appear at the temperature of about 500 deg C and at 475 deg C there has been much bainite over the whole cross section of the specimen. It is revealed that an increase of heating temperature and cooling rate replace the starting point of bainite transformation upwards. The strongest displacement of the point Bsub(S) into hogh-temperature range takes place after heating steel with the initial bainite structure in intercritical temperature range

  10. A theory of piezoelectric, elastic, and dielectric properties of the KH2PO4 family crystals under the strain u6. Phase transition and the piezoelectric effect in the KH2PO4 crystal

    International Nuclear Information System (INIS)

    Levits'kij, R.R.; Lyisnij, B.M.

    2003-01-01

    In order to study the dielectric, piezoelectric and elastic properties of ferroelectrics and antiferroelectrics of the KH 2 PO 4 family, we consider an extended proton tunneling model that takes into account the shear strain u 6 . In the four-particle cluster approximation for the short-range interactions and the mean field approximation for the long-range interaction we calculate the transverse components of the dielectric susceptibility tensor of the KH 2 PO 4 family ferroelectrics

  11. Water vapor pressure over molten KH_2PO_4 and demonstration of water electrolysis at ∼300 °C

    International Nuclear Information System (INIS)

    Berg, R.W.; Nikiforov, A.V.; Petrushina, I.M.; Bjerrum, N.J.

    2016-01-01

    Highlights: • The vapor pressure over molten KH_2PO_4 was measured by Raman spectroscopy to be about 8 bars at ∼300 °C. • Raman spectroscopy shows that molten KH_2PO_4 under its own vapor pressure contains much dissolved water. • It is demonstrated spectroscopically that water electrolysis is possible in KH_2PO_4 electrolyte forming H_2 and O_2 at 300 °C. • Molten KH_2PO_4 is a possible electrolyte for water electrolysis. - Abstract: A new potentially high-efficiency electrolyte for water electrolysis: molten monobasic potassium phosphate, KH_2PO_4 or KDP has been investigated at temperatures ∼275–325 °C. At these temperatures, KH_2PO_4 was found to dissociate into H_2O gas in equilibrium with a melt mixture of KH_2PO_4−K_2H_2P_2O_7−KPO_3−H_2O. The water vapor pressure above the melt, when contained in a closed ampoule, was determined quantitatively vs. temperature by use of Raman spectroscopy with methane or hydrogen gas as an internal calibration standard, using newly established relative ratios of Raman scattering cross sections of water and methane or hydrogen to be 0.40 ± 0.02 or 1.2 ± 0.03. At equilibrium the vapor pressure was much lower than the vapor pressure above liquid water at the same temperature. Electrolysis was realized by passing current through closed ampoules (vacuum sealed quartz glass electrolysis cells with platinum electrodes and the electrolyte melt). The formation of mixtures of hydrogen and oxygen gases as well as the water vapor was detected by Raman spectroscopy. In this way it was demonstrated that water is present in the new electrolyte: molten KH_2PO_4 can be split by electrolysis via the reaction 2H_2O → 2H_2 + O_2 at temperatures ∼275–325 °C. At these temperatures, before the start of the electrolysis, the KH_2PO_4 melt gives off H_2O gas that pressurizes the cell according to the following dissociations: 2KH_2PO_4 ↔ K_2H_2P_2O_7 + H_2O ↔ 2KPO_3 + 2H_2O. The spectra show however that the water by

  12. Specific electrical conductivity in molten potassium dihydrogen phosphate KH2PO4 - An electrolyte for water electrolysis at ∼300°C

    DEFF Research Database (Denmark)

    Nikiforov, Aleksey Valerievich; Berg, Rolf W.; Petrushina, Irina

    2016-01-01

    The conductivity of pure molten KH2PO4 salt and four mixtures with more or less water (KH2PO4-H2O and KH2PO4-KPO3 systems, respectively) were measured at temperatures of 240-320°C and under their own water vapor pressures. Molten KH2PO4 has been proven to be a promising electrolyte for an elevated...

  13. Influence of quantity of non-martensite products of transformation on resistance to fracture of improving structural steel

    International Nuclear Information System (INIS)

    Gulyaev, A.P.; Golovanenko, Yu.S.; Zikeev, V.N.

    1978-01-01

    18KhNMFA, low-carbon, alloyed steel and 42KhMFA medium-carbon, alloyed steel have been examined. For the purpose of obtaining different structures in hardening the steel, different cooling rates, different temperatures and isothermal holding times are applied. The following has been shown: on tempering to the same hardness (HV 300), the presence of non-martensite structures in hardened state does not practically influence the standard mechanical properties of steel (sigmasub(B), sigmasub(0.2), delta, PSI). The resistance of steel to the brittle failure is enhanced by the uniform, fine-disperse distribution of the carbide phase in the structure of lower bainite (up to 80 % bainite in martensite for 42KhMF steel to be improved), as well as strongly fragmented packages of rack martensite-bainite (up to 50 % lower bainite in martensite of 18KhNMFA steel). The formation of the upper bainite in the structure of the hardened steels 18KhNMFA and 42KhMF results on tempering in the formation of coarse, non-uniform, branched carbide inclusions, and this, in its turn, leads to raising the cold-shortness threshold and to lowering the amount of work as required for propagation of a crack. The presence of ferritic-pearlitic structures in the structural steels hardened to martensite and bainite results in reducing the resistance of steel to the brittle failure; the presence of every 10 % ferritic-pearlitic component in martensite of the structural steels 18KhNMFA and 42KhMFA to be thermally improved, raises T 50 by 8 deg and 20 deg C, respectively

  14. Effect of hot rolling on the structure and the mechanical properties of nitrogen-bearing austenitic-martensitic 14Kh15AN4M steel

    Science.gov (United States)

    Bannykh, O. A.; Betsofen, S. Ya.; Lukin, E. I.; Blinov, V. M.; Voznesenskaya, N. M.; Tonysheva, O. A.; Blinov, E. V.

    2016-04-01

    The effect of the rolling temperature and strain on the structure and the properties of corrosionresistant austenitic-martensitic 14Kh15AN4M steel is studied. The steel is shown to exhibit high ductility: upon rolling in the temperature range 700-1100°C at a reduction per pass up to 80%, wedge steel specimens are uniformly deformed along and across the rolling direction without cracking and other surface defects. Subsequent cold treatment and low-temperature tempering ensure a high hardness of the steel (50-56 HRC). Austenite mainly contributes to the hardening upon rolling in the temperature range 700-800°C at a reduction of 50-70%, and martensite makes the main contribution at higher temperatures and lower strains. Texture does not form under the chosen deformation conditions, which indicates dynamic recrystallization with the nucleation and growth of grains having no preferential orientation.

  15. Damping capacity of unstable steels on chromium-nickel-manganese base

    Energy Technology Data Exchange (ETDEWEB)

    Kochkin, L.I.; Rudakov, A.A. (Kirovskij Politekhnicheskij Inst. (USSR))

    1982-02-01

    The paper deals with results of a study on the energy scattering in OKh13N3G8, 20Kh13N3G4 and 30Kh13N3G4 unstable steels. It is shown that the development of microplastic strains most easily occurs in low-carbon steel having a two-phase structure in the initial state. The proceeding of microplastic deformations in carbon unstable steels is limited by the interstitial atom effect on the dislocation movement. It is established that in OKh13N3G8 steel the martensite ..cap alpha --> gamma..- transformation begins under the cyclic stress amplitudes below the yield point of this steel. The steels studied possess a high vibrostrength.

  16. Effect of metal properties of casts of steel-15Kh1M1FL on the crack resistance at 565 deg C

    International Nuclear Information System (INIS)

    Gladshtejn, V.I.; Sheshenev, M.F.

    1976-01-01

    Results are given of prolonged tests of the metal of industrial casts with various fluidity limits. It has been shown experimentally that a quite satisfactory crack resistance is characteristic of a metal with a fluidity limit in the range 30-50 kgf/mm 2 . Metallographic studies have been conducted. Upon variation of the structure and properties of the 15Kh1M1FL steel during operation, the rate of growth of small cracks (up to 2.0 mm) decreases almost by 3 orders of ten (from 1.4x10 -4 to 2.0x10 -7 mm/hour). Subsequent structural changes during prolonged operation (over 50000 hours) result in a gradual increase in the rate of crack growth. At the same time resistance towards appearance of the impermissible high rate of the crack growth, Ksub(10sup(-3)), diminishes monotonically with the operation time. The metal of industrial 15Kh1M1FL steel casts has good crack resistance (Ksub(10sup(-3)) =30-70 kgf/mmsup(3/2) and Vsub(ef) =) kgf/mm 2 ) and a satisfactory local plasticity (critical opening being no more than 0.20 mm for 10 3 hours)

  17. Parametrical limits of SCC-susceptibility of austenitic and austenitic-ferritic Cr-Ni steels

    International Nuclear Information System (INIS)

    Starosvetskij, D.I.; Baru, R.L.; Bondarenko, A.I.; Bogoyavlenskij, V.L.; Timonin, V.A.

    1990-01-01

    Comparative investigations into corrosion cracking (CC) of austenitic (12Kh18N10T) and austenitic-ferritic (08Kh22N6T) chromium-nickel steels are performed for various chloride media in a wide range of chloride concentrations and temperatures. It is shown that the ratio between steels in terms of their CC-susceptibility is not definite and can undergo a reversal depending on parameters of medium, level and conditions of loading. Differences in mechanisms of corrosion cracking of austenitic and austenitic-ferritic steels are established

  18. On the protective effect of KhOSP-10 inhibitor during corrosion, hydrogenadsorption and corrosion cracking of a steel in sulfuric acid

    International Nuclear Information System (INIS)

    Mindyuk, A.K.; Svist, E.I.; Savitskaya, O.P.; Goyan, E.B.; Gopanenko, A.N.

    1975-01-01

    The protective propeties of inhibitor KhOSP-10 in the time of corrosion and corrosive cracking of steel 40Kh are higher then those of inhibitors KPI-1, KI-1, I-I-V etc. Its ability to reduce steel hydrogenation is the same as in the case of KPI-1 inhibitor i.e. below that of KI-1. HCl additives enhance the efficiency of inhibitors KPI-1, KI-1, I-1-V etc. up to the protective ability of KhOSP-10. Kinetics of the electrode processes was estimated from polarization curves

  19. Corrosion failure of a bolt made of the 25Kh1MF material

    International Nuclear Information System (INIS)

    Liska, V.; Cechova, D.; Velkoborsky, J.

    1989-01-01

    M36x4 bolts, of which there are 222 at each nuclear power plant unit, are made of the 25Kh1MF or 38KhN3MFA steel. They are located in an environment with elevated temperature, with damp air and with boric acid. Corrosion of these bolts is due to the rather poor metallurgical quality of the steel. No inadmissible inhomogeneities of the type of lines of inclusions occur in the bolt material produced by cold rolling but defects of the type of laps were found on the threads. It is suggested that if the cold rolling technology were obviated, corrosion failure of the bolts might not occur. (M.D.). 7 figs., 3 refs

  20. Long-term strength and allowable stresses of grade 10Kh9MFB and X10CrMoVNb9-1 (T91/P91) chromium heat-resistant steels

    Science.gov (United States)

    Skorobogatykh, V. N.; Danyushevskiy, I. A.; Schenkova, I. A.; Prudnikov, D. A.

    2015-04-01

    Currently, grade X10CrMoVNb9-1 (T91, P91) and 10Kh9MFB (10Kh9MFB-Sh) chromium steels are widely applied in equipment manufacturing for thermal power plants in Russia and abroad. Compilation and comparison of tensile, impact, and long-term strength tests results accumulated for many years of investigations of foreign grade X10CrMoVNb9-1, T91, P91, and domestic grade 10Kh9MFB (10Kh9MFB-Sh) steels is carried out. The property identity of metals investigated is established. High strength and plastic properties of steels, from which pipes and other products are made, for operation under creep conditions are confirmed. Design characteristics of long-term strength on the basis of tests with more than one million of hour-samples are determined ( and at temperatures of 500-650°C). The table of recommended allowable stresses for grade 10Kh9MFB, 10Kh9MFB-SH, X10CrMoVNb9-1, T91, and P91 steels is developed. The long-time properties of pipe welded joints of grade 10Kh9MFB+10Kh9MFB, 10Kh9MFB-Sh+10Kh9MFB-Sh, X10CrMoVNb9-1+X10CrMoVNb9-1, P91+P91, T91+T91, 10Kh9MFB (10Kh9MFB-Sh)+X10CrMoVNb9-1(T/P91) steels is researched. The welded joint reduction factor is experimentally determined.

  1. Effect of austenitization conditions on kinetics of isothermal transformation of austenite of structural steels

    International Nuclear Information System (INIS)

    Konopleva, E.V.; Bayazitov, V.M.; Abramov, O.V.; Kozlova, A.G.

    1987-01-01

    Effect of austenization of kinetics of pearlite and bainite transformations for steels with different carbon content differing by alloying character and degree has been investigated. Austenization temperature increase is shown to leads to retardation of ferrite-pearlite transformation in low- and medium-carbon alloyed steels. Step-like holding in the region of austenite stable state (850, 950 deg) after high-temperature heating (1100 deg C) increases the rate of transformation partially recovering its kinetics and decomposition velocity after low-temperature heating in steels alloyed advantageously with carbide-forming elements (08Kh2G2F, 30Kh3) and does not affect kinetics in the 35Kh, 30KhGSN2A, 45N5 steels. Increase of heating temperature and growth of an austenite grain cause considerable acceleration of bainite transformation, increase of the temperaure of bainite transformation beginning and increase of the transformation amplitude in the 08Kh2G2F, 30Kh3 steels and affect weakly kinetics in steels with mixed alloying (30KhGSN2A) or low-alloy one (35Kh). The bainite transformation rate in the 45N5 steelite does not depend on austenization. The effect of additional acceleration of bainite transformation as a result holding after high-temperature heating in those steels, where activation of transformation occurs with increase of heating temperature

  2. Damping capacity of unstable steels on chromium-nickel-manganese base

    International Nuclear Information System (INIS)

    Kochkin, L.I.; Rudakov, A.A.

    1982-01-01

    The paper deals with results of a study on the energy scattering in OKh13N3G8, 20Kh13N3G4 and 30Kh13N3G4 unstable steels. It is shown that the development of microplastic strains most easily occurs in low-carbon steel having a two-phase structure in the initial state. The proceeding of microplastic deformations in carbon unstable steels is limited by the interstitial atom effect on the dislocation movement. It is established that in OKh13N3G8 steel the martensite α→γ- transformation begins under the cyclic stress amplitudes below the yield point of this steel. The steels studied possess a high vibrostrength [ru

  3. Topic 1. Steels for light water reactor pressure vessels

    International Nuclear Information System (INIS)

    Brumovsky, M.; Brynda, J.; Kepka, M.; Barackova, L.; Vacek, M.; Havel, S.; Cukr, B.; Protiva, K.; Petrman, I.; Tvrdy, M.; Hyspecka, L.; Mazanec, K.; Kupca, L.; Brezina, M.

    1980-01-01

    Part 1 of the Proceedings consists of papers on the criteria for the selection and comparison of the properties of steel for pressure vessels and on the metallurgy of the said steels, the selection of suitable material for internal tubing systems, the manufacture of high-alloy steels for WWER components, the mechanical and metallurgical properties of steel 22K for WWER 440 pressure components, and of steel 10MnNi2Mo for the WWER primary coolant circuit, and the metallographic assessment of steel 0Kh18N10T. (J.P.)

  4. Experience manufacturing and properties of the high-strength corrosion-resistant magnetic 03Kh12K12D2 steel

    International Nuclear Information System (INIS)

    Fel'dgandler, Eh.G.; Moshkevich, E.I.; Bakuma, S.F.; Bulat, S.I.; Tikhonenko, V.D.

    1976-01-01

    In industrial conditions, steel 03Kh12K12D2 (DI48-VD) was melted in a 7-tinduction furnace with subsequent vacuum arc remelting. Ingots of dia 500 and 630 mm were forged into slabs and forgings. The slabs were rolled into sheets, 40 mm thick, and the forgings were rolled into sectional shapes. To obtain the optimum mechanical, corrosion, and magnetic properties, the metal was annealed at 600 deg C (10 hr) and 650 deg C (5 and 10 hr). The developed melting and remelting process enabled to obtain steel meeting all the requirements as for the chemical composition, workability, and mechanical magnetic properties. On testing in water with high parameters (200 deg C, 16 kgf/cm 2 ) and in synthetic sea water (70-90 deg C) the corrosion rate did not exceed 1 μm per year

  5. Effect of the isothermal transformation temperature on the fine structure of steel-12Kh1MF

    International Nuclear Information System (INIS)

    Mints, I.I.; Berezina, T.G.; Lanskaya, K.A.

    1976-01-01

    For detailed analysis of bainite and pearlite in steel 12Kh1MF, homogeneous structures were obtained by isothermal annealing at 350, 450, 500, and 650 0 for 1 h. Isothermal transformation of austenite leads to the formation of bainite at 350-500 0 and pearlite at 650 0 . The austenitizing temperature was 980 0 for both types of samples, with holding for 20 min. For comparison, the plates were quenched from 980 0 and 1050 0 in ice-cold brine. The investigation was conducted with use of light and electron microscopes and x-ray analysis. The long-term strength was also determined. Isothermal treatment of steel 12Kh1MF at 350-500 0 C leads to the formation of a structure consisting of upper and lower bainite. At 500 0 the structure consists primarily of upper bainite, and at 350 0 of lower bainite. With tempering of the steel with a structure of upper and lower bainite at 730 0 for 3 h the dislocations undergo redistribution of the polygonization type within ferrite needles, with development of a cellular substructure. The acicular structure of the matrix is retained in this case. The density and evenness of the distribution of carbides is higher in upper bainite than in lower bainite. Steel 12Kh1MF with a structure of upper bainite is more susceptible to recrystallization as compared with a structure of lower bainite, which is responsible for the higher heat resistance of the latter

  6. Development of production technology and investigation of quality for forged-welded turbine rotors of steel 25Kh2NVFA

    International Nuclear Information System (INIS)

    Borisov, I.A.; Merinov, G.N.; Slezkina, E.V.

    1997-01-01

    A study was made into mechanical properties and microstructure of turbine rotor components manufactured by forging and heat treated under various conditions. It is revealed that the optimal heat treatment of forgings must include double quenching with subsequent tempering at 630-640 deg C for 10-20 h. Forged and welded rotors should be tempered at 620-630 deg C for 50-100 h. Microscopic examination and mechanical tests showed that low alloy steel 25Kh2NMF can be successfully used for manufacturing rotors of high-, medium-and low-heat turbines

  7. Water vapor pressure over molten KH2PO4 and demonstration of water electrolysis at ∼300ºC

    DEFF Research Database (Denmark)

    Berg, Rolf W.; Nikiforov, Aleksey Valerievich; Petrushina, Irina

    2016-01-01

    A new potentially high-efficiency electrolyte for water electrolysis: molten monobasic potassium phosphate, KH2PO4 or KDP has been investigated at temperatures ∼275–325 °C. At these temperatures, KH2PO4 was found to dissociate into H2O gas in equilibrium with a melt mixture of KH2PO4—K2H2P2O7—KPO3...... of water and methane or hydrogen to be 0.40 ± 0.02 or 1.2 ± 0.03. At equilibrium the vapor pressure was much lower than the vapor pressure above liquid water at the same temperature. Electrolysis was realized by passing current through closed ampoules (vacuum sealed quartz glass electrolysis cells...... with platinum electrodes and the electrolyte melt). The formation of mixtures of hydrogen and oxygen gases as well as the water vapor was detected by Raman spectroscopy. In this way it was demonstrated that water is present in the new electrolyte: molten KH2PO4 can be split by electrolysis via the reaction 2H2O...

  8. Corrosion resistance of heat exchange equipment in hydrotreating Orenburg Condensate

    International Nuclear Information System (INIS)

    Teslya, B.M.; Burlov, V.V.; Parputs, I.V.; Parputs, T.P.

    1986-01-01

    The authors study the corrosion resistance of materials of construction and select appropriate materials for the fabrication of heat exchange equipment that will be serviceable under hydrotreating conditions. This paper discusses the Orenburg condensate hydrotreating unit which has been shut down repeatedly for repair because of corrosion damage to components of heat exchangers in the reactor section: tube bundles (08Kh18N10T steel), corrugated compensators (12Kh18N10T steel), and pins of the floating heads (37Kh13N8G8MFB steel). The authors recommend that the tube bundles and the compensators in heat exchangers in the reaction section should be fabricated of 08Kh21N6M2T or 10Kh17N13M2T steel. The pins have been replaced by new pins made of 10Kh17N13 X M2T steel, increasing the service life from 6-12 months to 2 years

  9. Plasticity of low carbon stainless steels

    International Nuclear Information System (INIS)

    Bulat, S.I.; Fel'dgandler, Eh.G.; Kareva, E.N.

    1975-01-01

    In the temperature range 800-1200 0 C and with strain rates of from 10 -3 to 3 s -1 , austenitic (000Kh18N12) and austenitic-ferrite (000Kh26N6) very low carbon stainless steels containing 0.02-0.03% C exhibit no higher resilience than corresponding ordinary steels containing 0.10-0.12% C. However, the plasticity of such steels (particularly two-phase steels) at 900-1100 0 C is appreciably inferior owing to the development of intergranular brittle fracture. Pressure treatment preceded by partial cooling of the surface to 850 0 C yields rolled and forged products with acceptable indices but is inconvenient technically. At the Zlatoustovsk and Ashin metallurgical plants successful tests have been performed involving the forging and rolling of such steels heated to 1280-1300 0 C without partial cooling; it was necessary to improve the killing conditions, correct the chemical composition (increasing the proportion of ferrite) and take measures against heat loss. (author)

  10. Defect accumulation in welded joints of 12Kh1MF steel steam pipelines during creep

    International Nuclear Information System (INIS)

    Anokhov, A.E.; Alekhova, I.A.

    1982-01-01

    Technique for investigation of micropore accumulation in 12Kh1MF steel welded joints is proposed. The micropore density in different zones of welded joints in non-uniform. It is shown that failure localization in welded joint in the softening zone during the creep takes place due to the micropore priority accumulation in this zone. It is found out that accumulation of residual deformations in different zones of 12Kh1MF welded joints under creep runs more uniformly as the level of working stresses decreases and test duration increases

  11. Structural steels for power generating equipment and heat and chemical heat treatments

    International Nuclear Information System (INIS)

    Astaf'ev, A.A.

    1979-01-01

    Development of structural steels for power generating equipment and for reactor engineering, in particular, is elucidated. Noted is utilization of the 15Kh2NMFA steels for the WWER-1000 reactor vessels, the 10GN2MFA steels for steam generators, pressurizers, vessels of the automatic emergency shut down and safety system; the 00Kh12N3DL steel for cast pump vessels and main locking bars. The recommendations on heat treatment of big forgings, for instance, ensuring the necessary complex of mechanical properties are given. Diffusion chromizing with subsequent nitriding of austenitic steels which increase durability of the components in BN reactors more than 4 times, is practised on a large scale

  12. On change of vanadium carbide state during 20Kh3MVF steel heat treatment

    International Nuclear Information System (INIS)

    Gitgarts, M.I.; Maksimenko, V.N.

    1975-01-01

    The Xray diffraction study of vanadium carbide MC has been made in the steel-20KH3MVF quenched from 970 and 1040 deg and tempered at 660 deg for 210 hrs. It has been found that the constant of the MC crystal lattice regularly varies with the temperature of isothermal hold-up. In the steel tempered after quenching two vanadium carbides of different content could co-exist simultaneously: carbide formed in the quenching process and carbide formed during tempering. The discovered effect of the temperature dependence of the MC content is, evidently, inherent also to other steels containing vanadium

  13. Specific electrical conductivity in molten potassium dihydrogen phosphate KH2PO4 - An electrolyte for water electrolysis at ∼300°C

    DEFF Research Database (Denmark)

    Nikiforov, Aleksey Valerievich; Berg, Rolf W.; Petrushina, Irina

    2016-01-01

    The conductivity of pure molten KH2PO4 salt and four mixtures with more or less water (KH2PO4-H2O and KH2PO4-KPO3 systems, respectively) were measured at temperatures of 240-320°C and under their own water vapor pressures. Molten KH2PO4 has been proven to be a promising electrolyte for an elevated...... temperature pressurized water electrolyzer demonstrating high conductivity of ∼0.30Scm-1 at 300°C. The conductivity data are given as polynomial functions of temperature and composition. The melting point of the pure salt under its own water vapor pressure was determined to be ∼272°C....

  14. Effect of heat treatment and rotor steels composition on hydrogen solubility

    International Nuclear Information System (INIS)

    Ivanov, A.I.; Samojlenko, L.V.; Gorovaya, O.N.; Najdovskij, A.G.; Bilik, I.; Kret, Ya.

    1988-01-01

    Measurements of equilibrium hydrogen adsorption in samples of 27KhN3MFA and 25Kh2NMFA steels were conducted. Carbide inclusions and doping additions, typical for rotor steels, don't produce noticeable effect on hydrogen solubility in

  15. Wear resistance and structural changes in nitrogen-containing high-chromium martensitic steels under conditions of abrasive wear and sliding friction

    International Nuclear Information System (INIS)

    Makarov, A.V.; Korshunov, L.G.; Schastlivtsev, V.M.; Chernenko, N.L.

    1998-01-01

    Martensitic nitrogen-containing steels Kh17N2A0.14, Kh13A0.14, Kh14G4A0.22 as well as steel 20Kh13 were studied for their wear resistance under conditions of friction and abrasion. Metallography, X ray diffraction analysis and electron microscopy were used to investigate the structural changes taking place in a thin surface layer on wearing. It is shown that an increase of nitrogen content of 0.14 to 0.22% promotes an enhancement of steel resistance to abrasive and adhesive wear, especially after tempering in the range of 500-550 deg C. Typically, the nitrogen-containing steels exhibit lower resistance to various types of wear in comparison with the steels with high-carbon martensite due to their lower deformability under conditions of friction loading

  16. Effect of 4-(N,N-diethylamino)benzaldehyde thiosemicarbazone on the corrosion of aged 18 Ni 250 grade maraging steel in phosphoric acid solution

    International Nuclear Information System (INIS)

    Poornima, T.; Nayak, Jagannath; Nityananda Shetty, A.

    2011-01-01

    Highlights: → DEABT as corrosion inhibitor for maraging steel in phosphoric acid. → Inhibition efficiency increases with increase in inhibitor concentration. → Inhibition efficiency decreases with increase in temperature. → Adsorption obeys Langmuir adsorption isotherm. - Abstract: 4-(N,N-diethylamino)benzaldehyde thiosemicarbazone (DEABT) was studied for its corrosion inhibition property on the corrosion of aged 18 Ni 250 grade maraging steel in 0.67 M phosphoric acid at 30-50 deg. C by potentiodynamic polarization, EIS and weight loss techniques. Inhibition efficiency of DEABT was found to increase with the increase in DEABT concentration and decrease with the increase in temperature. The activation energy E a and other thermodynamic parameters (ΔG ads 0 , ΔH ads 0 , ΔS ads 0 ) have been evaluated and discussed. The adsorption of DEABT on aged maraging steel surface obeys the Langmuir adsorption isotherm model and the inhibitor showed mixed type inhibition behavior.

  17. Fouling and biocorrosion of a high-alloy steel in the Golden Horn bay

    International Nuclear Information System (INIS)

    Koryakova, M.D.; Nikitin, V.M.; Suponina, A.P.; Kharchenko, U.V.; Zvyagintsev, A.Yu.

    2002-01-01

    The studies on the effect of contamination of the Golden Horn bay waters (the Peter the Great Bay in the Japanese Sea) on formation of the community of the bacterio- and macrofouling and corrosion resistance of the Kh18N10T high-alloy steel are continued. The dissolved and chemically absorbed oxygen, pH, saprophytes, oil-oxidizing, sulfate-reducing bacteria and heavy metals are among the medium indicators, characterizing the level of pollution of the regions of the samples testing. It is shown, that the obtained experimental data extend our understanding of the dependent effect of three factors: the sea medium → fouling → corrosion resistance of the Kh18N10T high-alloy steel [ru

  18. Non-destructive automated express method for determining the inclination of chromium-nickel steels IGC

    International Nuclear Information System (INIS)

    Nazarov, A.A.; Kamenev, Yu.B.; Kuusk, L.V.; Kormin, E.G.; Vasil'ev, A.N.; Sumbaeva, T.E.

    1986-01-01

    Methods of automated control of 18-10-type steel inclination to IGC are developed and a corresponding automated testing complex (ATS) is created. 08Kh18N10T steel samples had two variants of thermal treatment: 1) 1200 deg (5 h), 600 deg (50 h); 2) 1200 deg (5 h). Methods of non-destructive automated control of 18-10-type steel inclination to IGC are developed on the basis of potentiodynamic reactivation (PR) principle. Automated testing complex is developed, which has undergone experimental running and demonstrated a high confidence of results, reliability and easy operation

  19. Austenite strengthening and softening during hot deformation

    International Nuclear Information System (INIS)

    Tushinskij, L.I.; Vlasov, V.S.; Kazimirova, I.E.; Tokarev, A.O.

    1981-01-01

    Processes of formation of austenite structure of 20 and 12Kh18N10T steels during hot deformation and postdeformation isothermal holdings have been investigated by the methods of analysis of curves of hot deformation, high-temperature metallography and light microscopy. Deformation has been exercised by extention in vacuum with average 4x10 -2 s -1 rate. Deformation temperatures of steel 20 are 930 and 1000 deg C, of steel 12Kh18N10T - 1100 deg C. It is stated that dynamic recrystallization takes place in both investigated steels during hot deformation. In the carbonic steel it is developed by shifting sections of high-angular boundaries, flow stress in this case remains constant. Recrystallization is developed by subgrain coalescence in austenite steel, that brings about preservation of increased defect density in recrystallized volumes. As a result strengthening of steel is continued up to fracture during the increase of the deformation degree. Postdeformation weakening of 12Kh18N10T steel is slowed down as compared with weakening of carbonic steel [ru

  20. Methods for protection of high-strength welded stainless steel from corrosion cracking

    International Nuclear Information System (INIS)

    Lashchevskij, V.B.; Gurvich, L.Ya.; Batrakov, V.P.; Kozheurova, N.S.; Molotova, V.A.; Shvarts, M.M.

    1978-01-01

    The efficiency of protection from corrosion cracking under a bending stress of 100 kgf/mm 2 in a salt mist and in a sulphur dioxide atmosphere, of welded joints of steel 08Kh15N5D2T with metallizing, galvanic and varnish coatings and lubricants, and of steel 1Kh15N4AM3 with sealing compounds has been investigated. Metallization of welded joints with aluminium and zinc efficiently increases corrosion resistance in a salt mist. Galvanic coatings of Cd, Zn, and Cr increase the time to cracking in a salt mist from 2-3 to 60-80 days. The protective properties of varnishes under the effect of a salt mist decrease in the following sequence: epoxy-polyamide enamel EP-140, acrylic enamel C-38, silicone enamels KO-834, KO-811, and KO-814. In an atmosphere containing SO 2 0.15 vol.% at 100% relative humidity, the varnishes investigated, with the exception of the inhibited coating XC-596, show lower protective properties than in a salt mist. The high efficiency of protection from corrosion cracking in a salt mist of slots of steel 1Kh15N4AM3 when using organic sealing compounds U4-21 and U5-21, and also slushing lubricants and oils PVK, TsIATIM-201, K17, and AMS3 was established

  1. Inhibitor effect on corrosion of titanium alloys in muriatic solutions of titanium-magnesium production

    International Nuclear Information System (INIS)

    Dobrunov, Yu.V.; Volynskij, V.V.; Kolobov, G.A.; Kuznetsov, S.I.

    1977-01-01

    Corrosion tests of titanium alloys VTI-0, OT4, VT5-1 and steel Kh18N1OT in 10% and 18% HCl with additions of carnallite at 40 deg C have been carried out. It has been established that titanium alloys in 10% and 18% HCl containing 5 and 10% carnallite are sufficiently corrosion resistant in the presence of 0.1-1% FeCl or HNO 3 and can be used for manufacturing the equipment of recirculation gas scrubbers. Steel Kh18N10T is unstable in all the media tested. It is subjected to intensive pitting. Specimens of steel Kh18N10T have also revealed edge cracking

  2. The permeation behavior of deuterium through 1Cr18Ni9Ti stainless steel with TiN+TiC-TiN multiple films

    International Nuclear Information System (INIS)

    Xiong, Y.; Song, J.; Luo, D.; Lei, Q.; Chen, C.

    2015-01-01

    The prevention of tritium losses via permeation through structure components is an important issue in fusion technology. The production of thin layers on materials with low diffusivity and/or low surface recombination constants (so-called permeation barriers) seems to be the most practical method to reduce or hinder the permeation of tritium through materials. TiN+TiC+TiN multiple films are deposited on the surface of 1Cr18Ni9Ti stainless steel by ion-beam assisted deposition technology. The characteristics of films are tested by XPS ASEM and XRD, which shows that the film are compact and uniform with a thickness of about 15 μm, and have a good adherence with the substrate below 773 K. The diffraction peaks in the XRD patterns for TiC and TiN are broadened, implying that the multiple films are deposited on the surface of 1Cr18Ni9Ti stainless steel. Meanwhile, the C-H bonded CH 4 -appears in the infrared spectra of multiple films, suggesting that the CH 4 - is in a static state, so hydrogen atom cannot migrate from the site bonded with carbon to a neighboring site. The measured deuterium permeability in 1Cr18Ni9Ti stainless steel coated with multiple films is 2-3 orders of magnitude lower than that of pure 1Cr18Ni9Ti stainless steel substrate from 473 K to 773 K. However, this barrier is partly destroyed above 773 K

  3. Improving composition of protective coatings for steel casting

    International Nuclear Information System (INIS)

    Kuz'kina, N.N.; Pegov, V.G.; Bogatenkov, V.F.; Shub, L.G.; Raspopova, N.A.

    1983-01-01

    A radically new fuel-free slag-forming mixture used as protective coating for steel casting is introduced. The lack of combustible powders precludes explosion and fire Lazard in mixture preparation. Usage of the new mixture in stainless steel casting of Kh18N10T type permitted to improve the ingot surface quality and reduce spoilage from 1.16 to 0.66%

  4. Low-temperature nitriding of austenitic steel in a vibrofluidized bed

    Science.gov (United States)

    Baraz, V. R.; Grachev, S. V.

    1999-11-01

    The prospects for use of a vibrofluidized bed (VFB) for low-temperature nitrogen saturation of high-strength austenitic steel based on Cr-Ni-Mn (12Kh17N8G2S2MF) are considered. The positive effect of preliminary plastic deformation on the intensity of nitriding is described. The temperature and time parameters of nitriding in a VFB for strain-aging austenitic steel 12Kh17N8G2S2MF are shown to be adequate for the regimes of the final heat-treatment operation of aging. This creates the possibility of combining the operations of surface alloying and strain aging into a single cycle. This combined treatment increases substantially the resistance of the steel to cyclic loads while preserving the strength parameters. It is shown that the presented method of low-temperature nitriding in a VFB is expedient for improving the service characteristics of austenitic steel 12Kh17N8G2S2MF used for production of force springs of automobile brake systems.

  5. On choice of tempered steels

    International Nuclear Information System (INIS)

    Govorov, A.A.; Pan'shin, I.F.; Rakhmanov, V.I.

    1978-01-01

    For the purpose of developing a graphical method for choosing structural steels, a change in the propagation work of a crack and in the critical temperature of brittleness of 40, 40Kh, 40KhN, and 40KhNM steels, was examined depending on the hardness after hardening and tempering. A diagram enabling to choose the grade of steel for making an article of known dimensions according to the preset values of its mechanical properties has been plotted. The developed selection scheme takes into account the hardenability of steels and the influence of the hardness after thermal treatment on the cold-shortness of steel

  6. Effect of neutron irradiation on the properties of the repair welds of the 15Kh2MFA steel

    International Nuclear Information System (INIS)

    Morozov, A.M.; Khachaturyants, L.V.

    1986-01-01

    The authors studied the effect of neutron irradiation on the tendency of the metal belonging to the heat affected zone of the weld toward brittle fracture (an increase in the critical temperature of brittleness). For comparison, the authors studied the radiation embrittlement of the original base metal (steel 15Kh2MFA) subjected to the conventional heat treatment of the reactor frames consisting of hardening and high-temperature tempering. Along with these materials, the radiational embrittlement of the base metal in the rehardened condition without tempering was studied. It was concluded that the presence of the regions repaired according to this technology and located in the frame at the level of the reactor core does not pose the problem of decreased resistance to brittle fracture

  7. Quaternary (liquid + liquid) equilibria of aqueous two-phase polyethylene glycol, poly-N-vinylcaprolactam, and KH{sub 2}PO{sub 4}: Experimental and the generalized Flory-Huggins theory

    Energy Technology Data Exchange (ETDEWEB)

    Foroutan, Masumeh [Department of Physical Chemistry, Faculty of Chemistry, College of Science, University of Tehran, Enghelab Ave., Tehran 14155-6455 (Iran, Islamic Republic of)], E-mail: foroutan@khayam.ut.ac.ir; Zarrabi, Mona [Department of Physical Chemistry, Faculty of Chemistry, College of Science, University of Tehran, Enghelab Ave., Tehran 14155-6455 (Iran, Islamic Republic of)

    2008-06-15

    A quaternary (liquid + liquid) equilibrium study was performed to focus attention on the interaction parameters between poly-N-vinylcaprolactam (PVCL) and poly-ethylene glycol (PEG) as well as between other species. At first, the new experimental data of (liquid + liquid) equilibria for aqueous two-phase systems containing PEG, KH{sub 2}PO{sub 4}, and PVCL at T = 303.15 K have been determined. Then the Flory-Huggins theory with two electrostatic terms (the Debye-Huckel and the Pitzer-Debye-Huckel equations) has been generalized to correlate the phase behavior of the quaternary system. Good agreement has been found between experimental and calculated data from both models especially from the Pitzer-Debye-Huckel equation. Also an effort was done to compare the effect of temperature as well as addition of PVCL on the binodal curves of PEG, KH{sub 2}PO{sub 4}, and water. The effect of the type of salt on the binodals has been also studied, and the salting out power of the salts has been determined.

  8. Simulation of Microdamage and Evaluation of Remaining Life of Steam Conduit Components from New-Generation Refractory Steel 10Kh9MF-Sh

    Science.gov (United States)

    Gladshtein, V. I.

    2018-03-01

    The effects of microdamage on the remaining life of high-temperature components of steam conduits from high-chromium steel 10Kh9MF-Sh and low-alloy steel 12Kh1M1F are compared. To simulate the microdamage, specimens with a circular notch and different relative diameters are fabricated. Specimens with a notch simulating the highest degree of microdamage and smooth specimens are tested for long-term strength. The coefficient of the remaining life of a conduit is computed for the range of relative damage presenting practical interest.

  9. Investigation of Creep Processes and Microdamages in 10Kh9V2MFBR-Sh High-Chromium Steel

    Science.gov (United States)

    Grin', E. A.; Pchelintsev, A. V.

    2018-01-01

    During the modernization and the new construction of power units at TPPs in Russia, high-chromium martensitic steels with higher heat-resistant properties than the traditional perlite steels are increasingly used as structural materials. High-chromium steels have a necessary regulatory support for their use in domestic power engineering. However, up to the present time, the issue of assessing the quality of these steels at the analysis of their state during long-term operation remains open. The article proposed is one of the first attempts to create a system of quality criteria for martensitic steels based on their microdamage parameters. Tests were carried out on the long-term strength and creep of samples from 10Kh9V2MFBR-Sh steel at high temperatures with the construction of creep curves in relative coordinates "deformation related to the deformation of fracture, current time related to time to failure." For some samples, the tests were interrupted and the metal was subjected to metallographic studies consisting of the analysis of microdamage with reference to the accumulated creep strain. It has been shown experimentally that the deformation curve of high-chromium steel differs from the analogous curve of pearlitic steel by a longer and flat section of steady creep and by a sharper transition to the third accelerated creep stage, which has a very short time period (approximately 10% of the total durability). The tendency to the increase in the microdamage of the structure of steel as the accumulated creep strain increases with time was confirmed. The beginning of transition to the final creep phase is characterized by the formation of contours of future pore chains and by the appearance of individual large pores of up to 6 μm in size, the presence of which in the microstructure of the martensitic steel indicates a very significant accumulation of creep strain, and corresponds to the predestruction stage of metal. It is necessary to continue the research to

  10. Effect of melting technique on grain size and heat resistance of the 12Kh1MF steel

    International Nuclear Information System (INIS)

    Lanskaya, K.A.; Kulikova, L.V.; Butneva, N.I.

    1978-01-01

    Investigated are the 12Kh1MF steel melted in open-hearth and arc furnaces (deoxidation by aluminium in 1.0 kg/t quantity) and then subjected to electroslag melting. The size of an austenitic grain depends on the residual contents of nitrogen and aluminium in steel. The open-hearth metal subjected to electroslag melting and containing a small quantity of nitrogen (0.006%) and aluminium (0.013%) has coarse austenitic grains and higher heat resistance compared to the steel melted in an arc furnace and also sub ected to electroslag melting. The nitride analysis of steel is carried out

  11. Specific features of the occurrence, development, and re-compaction of spall and shear fractures in spherically-convergent shells made of unalloyed iron and some steels under their spherical explosive loading

    International Nuclear Information System (INIS)

    Kozlov, E.A.; Brichikov, S.A.; Gorbachev, D.M.; Brodova, I.G.; Yablonskikh, T.I.

    2007-01-01

    Results of comparative metallographic examination of recovered shells exposed to explosive loading in two modes (with and without a heavy casing confining explosion products scatter) are presented. The shells were made of high-purity and technical-grade unalloyed iron with the initial grain size 250 and 125 μm, steel 30KhGSA in delivery state and quenched up to HR C 35...40, austenitic stainless steel 12Kh18N10T. The heavy casing used in experiments is demonstrated to ensure a rather compact convergence of shells destroyed at high radii. In the described comparative experiments, one managed to compile the 12Kh18N10T steel shell, after it was spalled at high radii and exposed to shear fracture and spallation layer fragmentation at medium radii, into a compact sphere but failed to do the same with the 30KhGSA quenched steel shell after it was fractured according to spall and shear mechanisms at high and medium radii. Polar zones of this steel shell have obvious undercompressed areas due to significant dissipative losses to overcome the shear strength. Occurrence, development, and re-compaction of spall and shear fractures in spherically-convergent shells made of materials, which were already carefully investigated in 1D- and 2D-geometry experiments, were systematically studied in order to verify and validate new physical models of dynamic fractures, as well as up-to-date used in 1D-, 2D- and 3D-numerical algorithms [ru

  12. Chemical heat treatment of low alloyed maraging steels

    Energy Technology Data Exchange (ETDEWEB)

    Malinov, L S; Korotich, I K [Zhdanovskij Metallurgicheskij Inst. (Ukrainian SSR)

    1979-09-01

    The investigation concerned the nitriding, cementation, chromizing, borating of economically alloyed maraging grade 04Kh2N5MFYu steel. The investigated methods of chemothermal treatment were found to considerably increase the hardness of the surface layer of the maraging steel. The high tempering of the grade 04Kh2N5MFYu cemented and hardened steel was found to produce secondary hardening. On chromizing, the diffusion layer is an alloyed ferrite which strengthens because of the dispersion hardening on ageing. The formation of the plastic low-carbon martensite at relatively small cooling rates greatly decreases the tendency of the boride layer to cracking.

  13. Choice of corrosion-resistant metal for fluotitanic acid

    International Nuclear Information System (INIS)

    Reingeverts, M.D.; Lapchenko, E.P.; Semenyuk, E.Y.

    1986-01-01

    The authors investigate the corrosion and anodic behavior of steels 12Kh18N10T, 08Kh21N6M2T, and 06KhN28MDT, nickel, and molybdenum in 10-40% naturally aerated solutions of H 2 TiF 6 at 20 and 50 degrees C. The authors found that in solutions of fluotitanic acid, as also in tetrafluoroboric and hydrofluoric acids, the most stable alloys are chromium-nickel-molybdenum alloy of type 06KhN28MDT and (for acid concentrations above 20%) copper-nickel-alloys of the monel metal type. Steels 12Kh18N10T and 08Kh21N6M2T can be used in acid concentrations of less than 10% and temperatures up to 20 degrees C with anodic protection

  14. Effect of KH2PO4 on gene expression, morphological and biochemical characteristics of stevia rebaudiana Bertoni under in vitro conditions.

    Science.gov (United States)

    Kahrizi, D; Ghari, S M; Ghaheri, M; Fallah, F; Ghorbani, T; Beheshti Ale Agha, A; Kazemi, E; Ansarypour, Z

    2017-08-15

    Stevia rebaudiana is one of the most important biologically sourced and low-calorie sweeteners Bertoni that has a lot of steviol glycosides. Tissue culture is the best for propagation of stevia and micro nutrients can affect both morphological traits and steviol glycosides production. Therefore, the effect of different concentrations of KH2PO4on stevia growth factors and gene expression had been studied by tissue culture methods, RT-PCR and HPLC. According the results, bud numbers had increased significantly in MS + 0.034 mMKH2PO4 media and the highest measured length was seen in plants grown under MS + 0.034 mM KH2PO4 treatment. Also, the highest growth rate (1.396 mm/d) was observed in MS + 0.034 mMKH2PO4.The best concentration of KH2PO4 for expression of UGT74G1 was 0.00425mMand the best one for UGT76G1 expression was 0.017mM. Interestingly, the best media for both stevioside and rebaudioside A accumulation was 0.017mM KH2PO4containing media. There was positive correlation between the best media for gene expression and the best one for steviol glycosides production.

  15. Joint formation of dissimilar steels in pressure welding with superposition of ultrasonic oscillations

    Energy Technology Data Exchange (ETDEWEB)

    Surovtsev, A P; Golovanenko, S A; Sukhanov, V E; Kazantsev, V F

    1983-12-01

    Investigation results of kinetics and quality of carbon steel joints with the steel 12Kh18N10T, obtained by pressure welding with superposition of ultrasonic oscillations with the frequency 16.5-18.0 kHz are given. The effect of ultrasonic oscillations on the process of physical contact development of the surfaces welded, formation of microstructure and impact viscosity of the compound, is shown.

  16. Strength of low-carbon rotor steel

    International Nuclear Information System (INIS)

    Voropaev, V.I.; Filimonov, O.V.; Borisov, I.A.

    1988-01-01

    The results of studying the effect of chemical composition and thermal treatment regimes on the structural strength of steels of the 25KhN3MFA type are presented. It is shown that alloying with niobium from 0.01 to 0.08% steels with the increased nickel content (4.2-4.5%) contributes to the increase of structural strength and reduction of semibrittleness temperature. To obtain high values of strength and plastic properties cooling with the rate of 10 3 -10 5 K/hr is recommended

  17. Structural features and properties of the laser-deposited nickel alloy layer on a KhV4F tool steel after heat treatment

    Science.gov (United States)

    Shcherbakov, V. S.; Dikova, Ts. D.; Stavrev, D. S.

    2017-07-01

    The study and application of the materials that are stable in the temperature range up to 1000°C are necessary to repair forming dies operating in this range. Nickel-based alloys can be used for this purpose. The structural state of a nickel alloy layer deposited onto a KhV4F tool steel and then heat treated is investigated. KhV4F tool steel (RF GOST) samples are subjected to laser deposition using a pulsed Nd:YAG laser. A nickel-based material (0.02C-73.8Ni-2.5Nb-19.5Cr-1.9Fe-2.8Mn) is employed for laser deposition. After laser deposition, the samples are subjected to heat treatment at 400°C for 5 h, 600°C for 1 h, 800°C for 1 h, and 1000°C for 1 h. The microstructure, the phase composition, and the microhardness of the deposited layer are studied. The structure of the initial deposited layer has relatively large grains (20-40 μm in size). The morphology is characterized by a cellular-dendritic structure in the transition zone. The following two structural constituents with a characteristic dendritic structure are revealed: a supersaturated nickel-based γ solid solution and a chromium-based bcc α solid solution. In the initial state and after heat treatment, the hardness of the deposited material (210-240 HV 0.1) is lower than the hardness of the base material (400-440 HV 0.1). Only after heat treatment at 600°C for 1 h, the hardness increases to 240-250 HV0.1. Structure heredity in the form of a dendritic morphology is observed at temperatures of 400, 600, and 800°C. The following sharp change in the structural state is detected upon heat treatment at 1000°C for 1 h: the dendritic morphology changes into a typical α + γ crystalline structure. The hardness of the base material decreases significantly to 160-180 HV 0.1. The low hardness of the deposited layer implies the use of the layer material in limited volume to repair the forming surfaces of dies and molds for die casting. However, the high ductility of the deposited layer of the nickel

  18. Investigation into the Cyclic Strength of the Bodies of Steam Shutoff Valves from 10Kh9MFB-Sh Steel

    Science.gov (United States)

    Skorobogatykh, V. N.; Kunavin, S. A.; Prudnikov, D. A.; Shchenkova, I. A.; Bazhenov, A. M.; Zadoinyi, V. A.; Starkovskii, G. L.

    2018-02-01

    Steam shutoff valves are operated under complex loading conditions at thermal and nuclear power stations. In addition to exposure to high temperature and stresses resulting in fatigue, these valves are subjected to cyclic loads in heating-up-cooling down, opening-closing, etc. cycles. The number of these cycles to be specified in designing the valves should not exceed the maximum allowable value. Hence, the problem of cyclic failure rate of steam shutoff valve bodies is critical. This paper continues the previous publications about properties of the construction material for steam shutoff valve bodies (grade 10Kh9MFB-Sh steel) produced by electroslag melting and gives the results of investigation into the cyclic strength of this material. Fatigue curves for the steal used for manufacturing steam shutoff valve bodies are presented. The experimental data are compared with the calculated fatigue curves plotted using the procedures outlined in PNAE G-002-986 and RD 10-249-98. It is confirmed that these procedures may be used in designing valve bodies from 10Kh9MFB-Sh steel. The effect of the cyclic damage after preliminary cyclic loading of the specimens according to the prescribed load conditions on the high-temperature strength of the steel is examined. The influence of cyclic failure rate on the long-term strength was investigated using cylindrical specimens with a smooth working section in the as-made conditions and after two regimes of preliminary cyclic loading (training) at a working temperature of 570°C and the number of load cycles exceeding the design value, which was 2 × 103 cycles. The experiments corroborated that the material (10Kh9MFB-Sh steel) of the body manufactured by the method of electroslag melting had high resistance to cyclic failure rate. No effect of cyclic damages in the metal of the investigated specimens on the high-temperature strength has been found.

  19. Polarization mechanism and ferroelectric instability in KH2PO4

    International Nuclear Information System (INIS)

    Koval, S.; Migoni, R.L.; Kohanoff, J.; Bussmann-Holder, A.

    2000-11-01

    The polarization mechanism and the origin of ferroelectricity in KH 2 PO 4 (KDP) are studied by first-principles electronic structure calculations. In the low-temperature phase, the collective off-center ordering of the protons is accompanied by an electronic charge delocalization from the near and localization at the far oxygen within the O-H...0 bonds. Electrostatic forces, then, push the K + ions towards off-center positions, and induce a macroscopic polarization. The analysis of the correlation between different geometrical and electronic quantities, in connection with experimental data, supports the idea that the role of tunnelling in isotopic effects is irrelevant. Instead, geometrical quantum effects appear to play a central role. (author)

  20. [Effects of different amounts of phosphate fertilizers on copper, zinc transfer in red soil under the application of KH2PO4].

    Science.gov (United States)

    Guo, Liang; Li, Zhong-wu; Huang, Bin; Wang, Yan; Zhang, Yan

    2014-09-01

    In order to study the effects of different phosphate addition amounts on migration and transformation of heavy metals (Cu, Zn) in soil, an indoor leaching experiment using soil columns was carry out to study the leaching behavior of Cu and Zn. The KH2PO4 was chosen as the fertilizer application at the doses of 5 mg.kg-1, 15 mg.kg-1 and 25 mg.kg-1. The results showed that KH2PO4, could reduce the leachate pH, but different phosphate amounts had little effect on leachate pH, pH in leachate kept rising in the whole leaching process. With the application of KH2PO4, Cu migration was mainly in the surface layer while Zn migrated into deeper soil. Concentrations of Cu, Zn in deep soil leachate were low indicating that it was harmless to the shallow groundwater. After leaching, heavy metals mainly existed in the residual form in soil, the proportion of residual form of Cu was around 60% and the proportion of residual form of Zn was around 40%. High concentration of KH2PO4 helps the transformation of Zn from residual organic combination state to exchange state.

  1. Ductility of high chromium stainless steels

    International Nuclear Information System (INIS)

    Peretyat'ko, V.N.; Kazantsev, A.A.

    1997-01-01

    Aimed to optimize the hot working conditions for high chromium stainless steels the experiments were carried in the temperature range of 800-1300 deg C using hot torsion tests and cylindrical specimens of ferritic and ferritic-martensitic steels 08Kh13, 12Kh13, 20Kh13, 30Kh13 and 40Kh13. Testing results showed that steel plasticity varies in a wide range depending on carbon content. Steels of lesser carbon concentration (08Kh13 and 12Kh13) exhibit a sharp increase in plasticity with a temperature rise, especially in the interval of 1200-1250 deg C. Steels 20Kh13 and 30Kh13 display insignificant plasticity increasing, whereas plastic properties of steel 40Kh13 increase noticeably in the range of 1000-1300 deg C. It is shown that optimal hot working conditions for specific steel must be selected with account of steel phase composition at high temperatures

  2. Radiation embrittlement of WWER 440 pressure vessel steel and of some improved steels by western producers

    International Nuclear Information System (INIS)

    Koutsky, J.; Vacek, M.; Stoces, B.; Pav, T.; Otruba, J.; Novosad, P.; Brumovsky, M.

    1982-01-01

    The resistance was studied of Cr-Mo-V type steel 15Kh2MFA to radiation embrittlement at an irradiation temperature of around 288 degC. Studied was the steel used for the manufacture of the pressure vessel of the Paks nuclear reactor in Hungary. The obtained results of radiation embrittlement and hardening of steel 15Kh2MFA were compared with similar values of Mn-Ni-Mo type steels A 533-B and A 508 manufactured by leading western manufacturers within the international research programme coordinated by the IAEA. It was found that the resistance of steel 15Kh2MFA to radiation embrittlement is comparable with steels A 533-B and A 508 by western manufacturers. (author)

  3. On the nature of anomalies in temperature dependence of the OKh18N1OT steel yield strength after thermal cycling in the low temperature range

    International Nuclear Information System (INIS)

    Medvedev, E.M.; Lavrent'ev, F.F.; Kurmanova, T.N.

    1978-01-01

    Investigated were structural transformations in 0Kh18N10T steel as a result of heating and cooling and of deformation within the range of temperatures between 300 and 77 K, the quantity relationships between the said transformations and the variation of the yield limit with the temperature. The studies were conducted by metallography and mechanical test methods. It was shown that an increase in the number of heating and cooling cycles correlates with a loss in strength of the steel while deformation at 77 K. This anomaly in the temperature relationship of the yield limit is related to the appearance in the course of deformation of α-martensite with a BCC lattice. Deformation at 300 K increases the amount ea of epsilon-martensite, a decrses the effectve size of grain and, in consequence, increases the yield limit. The relationship between the yield limit and the grain size at the temperature of 300 K is described adequately by the Hall-Petch equation

  4. Fabrication of welded pipes of the KhN45Yu alloy

    International Nuclear Information System (INIS)

    Lyapunov, A.I.; Krichevskij, E.M.; L'vov, V.N.; Kozlov, N.N.; Kireeva, T.S.

    1977-01-01

    A highly heat-resistant KhN45Yu (EP 747) alloy has been developed; the alloy is designed to withstand prolonged service in the temperature range of 1000-1300 deg C, or short-term service at 1300-1400 deg C. The satisfactory ductility and good weldability of the alloy have made it possible to obtain sheets and pipes (32 x 2.0 mm) by argon arc welding. The ductility of pipes from EP 747 alloy exceeds that of pipes from KhN78T (EI 435) alloy by 5.10%, the strength being approximately equal. In regard to strength the welded joint differs little from the base metal. The ductility characteristics up to 900 deg C are also equal, since failure occurs in the base metal. At higher temperatures the welded joint fails in the metal of the weld, and its ductility drops sharply. The grain size of the base metal corresponds to No. 3-4. The welded joint has a cast structure with a grain size larger than No. 1, but its ductility characteristics are satisfactory. This structure ensures an increased long-term strength of the material at 1000-1200 deg C

  5. Heating temperature effect on ferritic grain size of rotor steel

    International Nuclear Information System (INIS)

    Cheremnykh, V.G.; Derevyankin, E.V.; Sakulin, A.A.

    1983-01-01

    The heating temperature effect on ferritic grain size of two steels 13Kh1M1FA and 25Kh1M1FA is evaluated. It is shown that exposure time increase at heating temperatures below 1000 deg C up to 10h changes but slightly the size of the Cr-Mo-V ferritic grain of rotor steel cooled with 25 deg C/h rate. Heating up to 1000 deg C and above leads to substantial ferritic grain growth. The kinetics of ferritic grain growth is determined by the behaviour of phases controlling the austenitic grain growth, such as carbonitrides VCsub(0.14)Nsub(0.78) in 13Kh1M1FA steel and VCsub(0.18)Nsub(0.72) in 25Kh1M1FA steel. Reduction of carbon and alloying elements content in steel composition observed at the liquation over rotor length leads to a certain decrease of ferritic grain resistance to super heating

  6. Influence of isothermal thermomechanical treatment on structure and properties of structural steels

    International Nuclear Information System (INIS)

    Smirnov, M.A.; Kaletin, A.Yu.; Schastlivthev, V.M.; Kaletina, Yu.V.

    1997-01-01

    A study is made into the structure and mechanical properties of steel 35KhGSA and 37KhN3A after isothermal hardening resulting in bainitic structure formation as well as after low-temperature thermomechanical treatment (LTTMT) combining the plastic deformation at the temperature of bainitic transformation and subsequent isothermal hardening. It is shown that LTTMT permits and essential enhancement of strength properties in steel 35KhGSA, high plasticity and impact strength being reserved. This is associated with bainitic structure refinement. In steel 37KhN3A the process of carbide formation takes place along with bainitic transformation, and LTTMT results in lesser strengthening. LTTMT is fount to not practically affect the tendency of structural steels to bainitic brittleness. This treatment promotes some shift of brittleness manifestation to lower temperatures

  7. Paramagnetic defects in KH{sub 2}PO{sub 4} crystals with high concentration of embedded TiO{sub 2} nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Grachev, Valentin G., E-mail: grachev@physics.montana.edu; Tse, Romand; Malovichko, Galina I. [Physics Department, Montana State University, Bozeman, Montana 59717 (United States); Pritula, Igor M.; Bezkrovnaya, Olga N.; Kosinova, Anna V. [Institute for Single Crystals, NAS of Ukraine, Kharkiv (Ukraine)

    2016-01-21

    Qualitative transformations of spectra of Electron Paramagnetic Resonance, EPR, were found in KH{sub 2}PO{sub 4} crystals grown from liquor with 10{sup −5}–10{sup −1 }wt. % of anatase TiO{sub 2} nanoparticles in comparison with nominally pure KH{sub 2}PO{sub 4}. The nanoparticles have larger segregation coefficient for prismatic parts of the crystals than for pyramidal ones. Significant decrease in resonance absorption, complete disappearance of EPR lines of Fe{sup 3+} and Cr{sup 3+} centers, and appearance of four weak lines of equal intensities together with broad asymmetric lines with g-factors about 2.07–2.5 was observed in pyramidal parts grown with concentration of TiO{sub 2} nanoparticles larger than the threshold value 10{sup −2 }wt. %. The four lines were attributed to non-controlled impurity As substituted for P. In the presence of TiO{sub 2} nanoparticles, non-paramagnetic AsO{sub 4}{sup 3−} clusters trap electrons becoming AsO{sub 4}{sup 4−}. Disappearance of Fe{sup 3+} and Cr{sup 3+} centers was explained by their recharge to “EPR-silent” states and/or pairing at the surface of TiO{sub 2} nanoparticles.

  8. Investigation of intergranular corrosion resistance of Cr16Ni25NMo6 steel

    International Nuclear Information System (INIS)

    Kamenev, Yu.B.; Nazarov, A.A.; Kuusk, L.V.; Majdeburova, T.F.

    1990-01-01

    The effect of 08Kh16N25AM6 steel susceptibility to intergranular corrosion on its intergranular cracking resistance in high-temperature water is investigated. In addition, the performed tests point to the susceptibility of sensibilized Kh16N25AM6 steel to intergranular corrosion in media simulating an agressive environment of power generation equipment; the latter requires a strict control over the resistance of weld joints of the above steel to intergranular corrosion. It is shown that Kh16N25AM6 type steel in sensibilized state is susceptible to intercrystalline corrosion cracking in high-temperature water which correlates with its susceptibility to intergranular corrosion established by AM GOST 6032-84 and potentiodynamic reactivation methods

  9. Investigation of 12Kh1MF steel resistance to brittle fractures

    International Nuclear Information System (INIS)

    Bologov, G.A.; Rushchits, T.Yu.

    1977-01-01

    The metal of hot-rolled steam pipe made of 12Kh1MF steel, which has been subjected to thermal treatment under laboratory conditions, and metal samples from acting steam pipes after different exploitation periods at 510-565 deg C have been investigated. The dependence of impact viscosity and its constituents on conditions of thermal treatment has been established. The energy consumed by the developing crack has been used as an impact viscosity criterion. Appropriate thermal treatment is capable of rehabilitating the impact viscosity of embrittled metal. Cold plastic deformation increases crack propagation rate in the initial metal and promotes embrittlement during exploitation. Ageing of the working metal reduces its capacity of stopping the developing crack and shifts the temperature threshold of brittleness towards positive temperature

  10. Measurement of trace elements in KH2PO4 crystals by x-ray fluorescence spectrometry

    International Nuclear Information System (INIS)

    Ryon, R.W.; Duewer, T.I.

    1981-02-01

    A non-destructive method is described for the quantitative measurement of impurities in KDP (KH 2 PO 4 ) crystals. Part per million concentrations of impurities can be determined with good accuracy in about one hour of instrument time. An energy dispersive x-ray spectrometer is used. Both the crystals and the solutions from which they are grown may be analyzed

  11. Nitrogen ion implantation effect on friction coefficient of tool steel

    International Nuclear Information System (INIS)

    Velichko, N.I.; Udovenko, V.F.; Markus, A.M.; Presnyakova, G.N.; Gamulya, G.D.

    1988-01-01

    Effect of nitrogen molecular ion implantation into KhVSG steel on the friction coefficient in the air and vacuum is investigated. Irradiation is carried out by the N 2 + beam with energy 120 keV and flux density 5 μ/cm 2 at room temperature in vacuum 5x10 -4 Pa. The integral dose of irradiation is 10 17 particle/cm 2 . Nitrogen ion implantation is shown to provide the formation of the modified layer changing friction properties of steel. The friction coefficient can either increase or decrease depending on implantation and test conditions. 4 refs.; 2 figs

  12. Mechanical and fracture properties at impact loading of selected steels for nuclear power engineering

    International Nuclear Information System (INIS)

    Buchar, J.; Bilek, Z.

    1988-01-01

    The possibilities are briefly characterized of experimental research of mechanical and fracture properties of steels used in nuclear power engineering. Attention is paid to plastic deformation and the assessment of fracture formation during impact loading. The results are reported for steels 15Kh2MFA and 10GN2MFA. For steel 15Kh2MFA the effect was also studied of neutron radiation at different temperatures. From the theory developed for non-irradiated material 10GN2MFA, a prediction is made within the original model of the fracture stress value for steel 15Kh2MFA in both non-irradiated and irradiated states. The conclusion is arrived at that the existing methods of assessing steel properties at impact load allow obtaining knowledge of all significant effects during actual stress, this using only small specimens of the materials. (Z.M.). 4 figs., 8 refs

  13. Development and industrial mastering hot rolling procedure for low-ductile steels and alloys

    International Nuclear Information System (INIS)

    Degterenko, V.K.; Sokolov, V.A.

    1980-01-01

    The technique for the development of the sheet hot rolling procedure for low-ductile steels and alloys (0Kh17N14M2, 12Kh21N5T, 20Kh25N20C2,40Kh13, 36NKhTYu etc.) is proposed, using plastometer which permits to obtain the data on the deformation resistance in the wide range of temperatures (800-1300 deg C), of deformation degrees (0.1-0.3) and deformation rates (0.001-300 c -1 ). With the help of the plastometric data processed on the computer the calculation of the rolling regimes for the sheet with improved surface quality is carried out at the more uniform loading on the mill stands

  14. Synthesis and inhibition of N-alkyl-2-(4-hydroxybut-2-ynyl) pyridinium bromide for mild steel in acid solution: Box–Behnken design optimization and mechanism probe

    International Nuclear Information System (INIS)

    Gu, Tianbin; Chen, Zhengjun; Jiang, Xiaohui; Zhou, Limei; Liao, Yunwen; Duan, Ming; Wang, Hu; Pu, Qiang

    2015-01-01

    Highlights: • N-alkyl-2-(4-hydroxybut-2-ynyl) pyridinium bromide prepared is new type of inhibitor. • Box–Behnken experiment design-based optimization model is used to maximize inhibition efficiency. • O-n adsorbing on X70 steel surface enhances the resistance of the steel to acid corrosion. • O-n acts as mix-type inhibitor to suppress both the anodic and cathodic reaction of X70 steel. - Abstract: N-alkyl-2-(4-hydroxybut-2-ynyl) pyridinium bromides (designated as O-n) was synthesized and characterized by 1 H and 13 C NMR and FTIR. Box–Behnken design (BBD)-based optimization was engaged to analyze the factors and the interaction of the factors that influence the corrosion inhibition efficiency of O-n for X70 steel. The inhibition mechanism was also probed by means of X-ray photoelectron spectroscopy (XPS), Tafel polarization and electrochemical impedance spectroscopy (EIS) techniques

  15. Comparison on Mechanical Properties of SA508 Gr.3 Cl.1, Cl.2, and Gr.4N Low Alloy Steels for Pressure Vessels

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Min-Chul; Park, Sang-Gyu; Lee, Bong-Sang [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Lee, Ki-Hyoung [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

    2014-10-15

    In this study, microstructure and mechanical properties of SA508 Gr.3 Cl. 1, Cl.2, and Gr.4N low alloy steels are characterized to compare their properties. To evaluate the fracture toughness in the transition region, the master curve method according to ASTM E1921 was adopted in the cleavage transition region. Tensile tests and Charpy impact tests were also performed to evaluate the mechanical properties, and a microstructural investigation was carried out. The microstructure and mechanical properties of SA508 Gr.3 Cl.1, Cl2 and Gr.4N low alloy steels were characterized.. The predominant microstructure of SA508 Gr.4N model alloy is tempered martensite, while SA508 Gr.3 Cl.1 and Cl.2 steels show a typical tempered upper bainitic structure. SA508 Gr. 4N model alloy shows the best strength and transition behavior among the three SA508 steels. SA508 Gr.3 Cl.2 steel also has quite good strength, but there is a loss of toughness.

  16. X-ray diffraction study of slags forming during corrosion resistant steel production

    International Nuclear Information System (INIS)

    Slavov, V.I.; Zadorozhnaya, V.N.; Shurygina, A.V.

    1990-01-01

    Using X-ray diffraction analysis slags, forming during corrosion-resistant 12Kh18N10T grade steel production by two flowsheets, are studied. Standard two-slag technology of steel production does not provide efficient disintegration of chromospinelides in slags, gives high steel contamination with respect to nonmetallic impurities, coarse structure and, as a consequence, presence of macrodefects on rolled products surface. One-slag steel melting technology with titanium alloying of the steel at vacuum causes fast removal of chromospinelides at the beginning of reduction period, promotes titanium absorption by the steel, refines nonmetallic inclusions, provides more fine structure and steel plasticity, removes surface defects

  17. On the low-cycle fracture of chromium-nickel-molybdenum structural steels in seawater

    International Nuclear Information System (INIS)

    Karpenko, G.V.; Kobzaruk, A.V.; Malyshevskij, V.A.; Shul'te, A.Yu.; Rybin, V.V.; Silaev, I.I.

    1977-01-01

    The processes of low-cycle fracture of the chrome-nickel-molybdenum steels 15KhN5MF, 12KhN4MF and 15KhN3M in air, and in sea water have been investigated by the optical microscopy method, and electron microscopic examination of thin films. Bringing no change in the fracture character, sea water produces a speeding-up effect on the low-cycle fatigue fracture process. During long-time corrosion fatigue testing considerable importance lies with the electrochemical corrosion factor expediting the occurrence of corrosive pits acting as crack-initiation nuclei, fatigue crack attack, accumulation of corrosion products in fatigue cracks, etc

  18. PET imaging of the brain serotonin transporters (SERT) with N,N-dimethyl-2-(2-amino-4-[18F]fluorophenylthio)benzylamine (4-[18F]-ADAM) in humans: a preliminary study

    International Nuclear Information System (INIS)

    Huang, Wen-Sheng; Huang, San-Yuan; Ho, Pei-Shen; Yeh, Chin-Bin; Ma, Kuo-Hsing; Huang, Ya-Yao; Shiue, Chyng-Yann; Liu, Ren-Syuan; Cheng, Cheng-Yi

    2013-01-01

    The aim of this study was to assess the feasibility of using 4-[ 18 F]-ADAM as a brain SERT imaging agent in humans. Enrolled in the study were 19 healthy Taiwanese subjects (11 men, 8 women; age 33 ± 9 years). The PET data were semiquantitatively analyzed and expressed as specific uptake ratios (SUR) and distribution volume ratios (DVR) using the software package PMOD. The SUR and DVR of 4-[ 18 F]-ADAM in the raphe nucleus (RN), midbrain (MB), thalamus (TH), striatum (STR) and prefrontal cortex (PFC) were determined using the cerebellum (CB) as the reference region. 4-[ 18 F]-ADAM bound to known SERT-rich regions in human brain. The order of the regional brain uptake was MB (RN) > TH > STR > PFC > CB. The DVR (n = 4, t* = 60 min) in the RN, TH, STR and PFC were 3.00 ± 0.50, 2.25 ± 0.45, 2.05 ± 0.31 and 1.40 ± 0.13, respectively. The optimal time for imaging brain SERT with 4-[ 18 F]-ADAM was 120-140 min after injection. At the optimal imaging time, the SURs (n = 15) in the MB, TH, STR, and PFC were 2.25 ± 0.20, 2.28 ± 0.20, 2.12 ± 0.18 and 1.47 ± 0.14, respectively. There were no significant differences in SERT availability between men and women (p 18 F]-ADAM was safe for human studies and its distribution in human brain appeared to correlate well with the known distribution of SERT in the human brain. In addition, it had high specific binding and a reasonable optimal time for imaging brain SERT in humans. Thus, 4-[ 18 F]-ADAM may be feasible for assessing the status of brain SERT in humans. (orig.)

  19. Numerical simulation of Cr2N age-precipitation in high nitrogen stainless steels

    International Nuclear Information System (INIS)

    Dai, Q.X.; Yuan, Z.Z.; Luo, X.M.; Cheng, X.N.

    2004-01-01

    At the temperature raging from 700 to 950 deg. C, the Cr 2 N age-precipitation in high nitrogen austenitic stainless steels Fe24Mn18Cr3Ni0.62N was investigated in this paper. A qualitative mathematical model of Cr 2 N age-precipitation, ln t S = f (Me,1/T), was established based on the thermodynamics and kinetics and phase transformation theories. Satisfactory results were obtained by means of the test of artificial neural network. This mathematical model can be applied to the calculation design and predication of Cr 2 N age-precipitation in high nitrogen stainless steels

  20. Fatigue resistance of Cr-Ni-Mo-V steel

    International Nuclear Information System (INIS)

    Naumchenkov, N.E.; Filimonova, O.V.; Borisov, I.A.

    1985-01-01

    A study was made on the effect of additional alloying (Ni, Ni+Co), stress concentration, surface plastic strain on fatigue resistance of rotor steel of Cr-Ni-Mo-V-composition. It is shown that the steel with decreased carbon content possesses high complex of mechanical properties. Fatigue characteristics are not inferior to similar characteristics of steels of 25KhN3MFA type. Additional alloying of the steel containing 0.11...0.17% C and 4.5...4.7% N:, with niobium separately or niobium and cobalt in combination enabled to improve fatigue resistance of samles up to 25%. Strengthening of stress concentration zones by surface plastic strain is recommended for improving rotor suppporting 'nower under cyclic loading

  1. Structural changes in complex steels with 12 % Cr during welding thermal cycle

    International Nuclear Information System (INIS)

    Ul'yanova, N.V.; Kurnosova, N.D.

    1981-01-01

    The structural changes in the heat affected zones of welded steam tubes of the 12Kh11V2MF and 18Kh12VMBFR steels, are investigated. A short-time heating of thin samples up to 1300-900 deg C with the aim of imitating the thermal welding cycle permits to determine temperatures of specific region formation in heat affeced zones of 12% Cr steels. The difference in the amounts and structure of σ-ferrite and γ-phase in these regions is established. A ''tongue'' nature of γ-phase grain growth is found in the temperature range of 1150-1100 deg C, while at 1300-1250 deg C σ-ferrite growth with the formation of saw-shape boundaries is observed. It is shown that tensile properties of imitated heat affected zone of 12Kh12VMBFP steel increase with heating temperature with the insignificant plasticity decrease. Impact strength on longitudinal samples decreases but remains higher than that determined by specifications [ru

  2. Parameter optimization for steel quenching by C02-laser irradiation

    International Nuclear Information System (INIS)

    Moryashchev, S.F.; Kislitsyn, A.A.; Kosyrev, F.K.

    1984-01-01

    The dependence of average absorption factor on maximal temperature of the article surface during quenching by CO 2 -laser irradiation was determined empirically. The calculations of depth of a hardening zone and process productivity in 40 Kh, 4Kh13 steels and Armco-iron with regard to this dependence were conducted

  3. Electric dipole moment in KH{sub 2}PO{sub 4} systematically modified by proton irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Jin Kweon, Jung; Lee, Cheol Eui [Department of Physics and Institute for Nano Science, Korea University, Seoul 136-713 (Korea, Republic of); Noh, S. J.; Kim, H. S. [Department of Applied Physics, Dankook University, Yongin 448-701 (Korea, Republic of)

    2012-01-01

    We have carried out an impedance spectroscopy study on a series of proton-irradiated KH{sub 2}PO{sub 4} (KDP) systems. A systematic modification was observed in the transverse dipole moment of the proton-irradiated KDP systems, associated with hydrogen-ion displacements, as obtained from dielectric constant measurements by using a mean-field approximation. Besides, intercorrelation of the charge transport with the dielectric properties was revealed, both having closely to do with the hydrogen-bond modification.

  4. SCC growth behavior of cast stainless steels in high-temperature water. Influences of corrosion potential, steel type, thermal aging and cold-work

    International Nuclear Information System (INIS)

    Yamada, Takuyo; Terachi, Takumi; Miyamoto, Tomoki; Arioka, Koji

    2011-01-01

    Recent studies on crack growth rate (CGR) measurement in oxygenated high-temperature pure water conditions, such as normal water chemistry (NWC) in BWRs, using compact tension (CT) type specimens have shown that stainless steel weld metal are susceptible to stress corrosion cracking (SCC). On the other hand, the authors reported that no significant SCC growth was observed on stainless steel weld metals in PWR primary water at temperatures from 250degC to 340degC. Cast austenitic stainless steels are widely used in light water reactors, and there is a similarity between welded and cast stainless steels in terms of the microstructure of the ferrite/austenite duplex structure. However, there are a few reports giving CGR data on cast stainless steels in the BWRs and PWRs. The principal purpose of this study was to examine the SCC growth behavior of cast stainless steels in simulated PWR primary water. A second objective was to examine the effects on SCC growth in hydrogenated and oxygenated water environments at 320degC of: (1) corrosion potential; (2) steels type (Mo in alloy); (3) thermal-aging (up to 400degC x 40 kh); and (4) cold-working (10%). The results were as follows: (1) No significant SCC growth was observed on all types of cast stainless steels: aged (400degC x 40 kh) of SCS14A and SCS13A and 10% cold-working, in hydrogenated (low-potential) water at 320degC. (2) Aging at 400degC x 40 kh SCS14A (10%CW) markedly accelerated the SCC growth of cast material in high-potential water at 320degC, but no significant SCC growth was observed in the hydrogenated water, even after long-term thermal aging (400degC x 40 kh). (3) Thus, cast stainless steels have excellent SCC resistance in PWR primary water. (4) On the other hand, significant SCC growth was observed on all types of cast stainless steels: 10%CW SCS14A and SCS13A, in 8 ppm-oxygenated (high-potential) water at 320degC. (5) No large difference in SCC growth was observed between SCS14A (Mo) and SCS13A. (6) No

  5. Effect of operational conditions of electroerosion machining on the surface microgeometry parameters of steels and alloys

    International Nuclear Information System (INIS)

    Foteev, N.K.

    1976-01-01

    Studies the influence of pulse duration and a series of operating conditions of a ShGI-40-440 spark-machining generator on changes in the basic surface microgeometry characteristics of components of stainless steel 1Kh18N10T, steel St 45 and hard alloy T14K8. The microgeometry characteristics of spark-machined surfaces differ significantly from the corresponding characteristics of surfaces machined by cutting and vibro-rolling

  6. Electron beam welding of flanges with tubular shafts of steel 40KhNMA

    International Nuclear Information System (INIS)

    Leskov, G.I.; Zhivaga, L.I.; Shipitsyn, B.N.; Savichev, R.V.

    1975-01-01

    The results are presented of elaborating the technological process for the electron beam welding of flanges with a tube of the 40KhNMA steel and of investigation into the quality of the welded joints. A welded piece has been fabricated conforming to the technology suggested observing the parameters worked-out in the following sequence: assembling the piece; pre-welding of the edges in some points; welding; high tempering; welds quality control; removal of the seam reinforcement inside of the tube and the weld root to the depth of 2 mm; quenching; tempering; welds quality control; finishing. The welds quality control consists in visual inspection, ultrasonic testing, magnetic flaw detection, as well as X-ray and metallographic analyses. The mechanical properties are studied on notched samples cut out of the welded joints. The test results have shown that the mechanical properties of the welded joints meet the requirements on the same level with the base metal

  7. Properties of structural steels melted out of high-purity charge

    International Nuclear Information System (INIS)

    Marchenko, V.N.; Sergeeva, T.K.; Kondakova, N.K.; Morozov, V.P.; Madorskij, L.L.

    1993-01-01

    A comparative evaluation has been made of impurities, mechanical properties and hydrogen embirittlement parameters for steels type 40Kh and 40KhS produced by electrometallurgical method with the use of direct reduced charge (DR-steels) and melted in an open-hearth furnace. Investigation results have shown that 40Kh and 40KhS Dr-steels have more coarse austenitic grains and experience more complete transformation of martensite into ferritic-pearlitic mixture on tempering. Threshold stresses increase 2.5 times due to purity enhancement at the expense of application of direct reduced charge

  8. Sources of optical distortion in rapidly grown crystals of KH2PO4

    International Nuclear Information System (INIS)

    De Yoreo, J.J.; Zaitseva, N.P.; Woods, B.W.; Land, T.A.; Rek, Z.U.

    1995-01-01

    We report results of x-ray topographic and optical measurements on KH 2 PO 4 crystals grown at rates of 5 to 30mm/day. We show that optical distortion in these crystals is caused primarily by 3 sources: dislocations, differences in composition between adjacent growth sectors of the crystal, and differences in composition between adjacent sectors of vicinal growth hillocks within a single growth sector of the crystal. We find that the compositional heterogeneities cause spatial variations in the refractive index and induced distortion of the transmitted wave front while large groups of dislocations are responsible for strain induced birefringence which leads to beam depolarization

  9. Annealing effect on restoration of irradiation steel properties

    International Nuclear Information System (INIS)

    Vishkarev, O.M.; Kolesova, T.N.; Myasnikova, K.P.; Pecherin, A.M.; Shamardin, V.K.

    1986-01-01

    The effect of temperature and annealing time on the restoration of properties of the 15Kh2NMFAA and 15Kh2MFA steels after irradiation at 285 deg with the fluence of 6x10 23 neutr/m 2 (E>0.5 MeV) is studied. Microhardness (H μ ) restoration in the irradiated 15Kh2NMFAA steel is shown to start from 350 deg C annealing temperature. The complete microhardness restoration is observed at the annealing temperature of 500 deg C for 10 hours

  10. PET imaging of the brain serotonin transporters (SERT) with N,N-dimethyl-2-(2-amino-4-[{sup 18}F]fluorophenylthio)benzylamine (4-[{sup 18}F]-ADAM) in humans: a preliminary study

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Wen-Sheng [PET Center, Tri-Service General Hospital, Department of Nuclear Medicine, Neihu, Taipei (China); Changhua Christian Hospital, Department of Nuclear Medicine, Changhua (China); Huang, San-Yuan; Ho, Pei-Shen; Yeh, Chin-Bin [Tri-Service General Hospital, Department of Psychiatry, Taipei (China); Ma, Kuo-Hsing [National Defense Medical Center, Department of Biology and Anatomy, Taipei (China); Huang, Ya-Yao; Shiue, Chyng-Yann [PET Center, Tri-Service General Hospital, Department of Nuclear Medicine, Neihu, Taipei (China); PET Center, National Taiwan University Hospital, Department of Nuclear Medicine, Taipei (China); Liu, Ren-Syuan [Taipei Veterans General Hospital, Department of Nuclear Medicine, Taipei (China); Cheng, Cheng-Yi [PET Center, Tri-Service General Hospital, Department of Nuclear Medicine, Neihu, Taipei (China)

    2013-01-15

    The aim of this study was to assess the feasibility of using 4-[{sup 18}F]-ADAM as a brain SERT imaging agent in humans. Enrolled in the study were 19 healthy Taiwanese subjects (11 men, 8 women; age 33 {+-} 9 years). The PET data were semiquantitatively analyzed and expressed as specific uptake ratios (SUR) and distribution volume ratios (DVR) using the software package PMOD. The SUR and DVR of 4-[{sup 18}F]-ADAM in the raphe nucleus (RN), midbrain (MB), thalamus (TH), striatum (STR) and prefrontal cortex (PFC) were determined using the cerebellum (CB) as the reference region. 4-[{sup 18}F]-ADAM bound to known SERT-rich regions in human brain. The order of the regional brain uptake was MB (RN) > TH > STR > PFC > CB. The DVR (n = 4, t* = 60 min) in the RN, TH, STR and PFC were 3.00 {+-} 0.50, 2.25 {+-} 0.45, 2.05 {+-} 0.31 and 1.40 {+-} 0.13, respectively. The optimal time for imaging brain SERT with 4-[{sup 18}F]-ADAM was 120-140 min after injection. At the optimal imaging time, the SURs (n = 15) in the MB, TH, STR, and PFC were 2.25 {+-} 0.20, 2.28 {+-} 0.20, 2.12 {+-} 0.18 and 1.47 {+-} 0.14, respectively. There were no significant differences in SERT availability between men and women (p < 0.05). The results of this study showed that 4-[{sup 18}F]-ADAM was safe for human studies and its distribution in human brain appeared to correlate well with the known distribution of SERT in the human brain. In addition, it had high specific binding and a reasonable optimal time for imaging brain SERT in humans. Thus, 4-[{sup 18}F]-ADAM may be feasible for assessing the status of brain SERT in humans. (orig.)

  11. X-ray spectrum microanalysis of copper and stainless steel surface layer after electroerosion machining

    International Nuclear Information System (INIS)

    Abdukarimov, Eh.T.; Saidinov, S.Ya.

    1989-01-01

    The results of experimental investigations of the surface layer of copper and steel 12Kh18N10T after electroerrosion treatment by a rotating tungsten electrode in natural and distilled water are presented. It is established that the quantity of electrode material transferred to the surface of the steel treated grows with the spark discharge energy increase. Tungsten concentration in the surface layer reaches 5-10% with the average depth of penetration 40-50 μm

  12. Hot working effect on austenite transformations in structural steel in continuous cooling

    International Nuclear Information System (INIS)

    Zajmovskij, V.A.; Kisteh, N.V.; Samedov, O.V.

    1979-01-01

    Austenite transformations in 40, 40Kh, 40KhN and 40KhNMA steels under hot working at 900 deg C with 20% reduction degree and continuous cooling with 1,7-16 0 /s are investigated. Changing of cooling rate in various ways affects the temperature range of austenite transformation in pearlite and bainite regions. Regulating the cooling rate after hot working one can essentially change the impact strength and steel ductility as a result of high temperature thermomechanical treatment effect

  13. Structure and phase composition of titanium nitride coating on austenitic steel

    International Nuclear Information System (INIS)

    Dubovitskaya, N.V.; Kolenchenko, L.D.; Larikov, L.N.

    1989-01-01

    Structure and phase composition of titanium nitride coating deposited on 08Kh18N10T steel substrate using ''Bulat'' device are studied. Use of complex investigation methods permitted despite small coating thickness (1μm) to aquire information on hardness, porosity, to study phase composition in all coating thickness. The surface layer (∼0.1 μm) consists of ε-Ti 2 N, TiN 0.6 , TiC 0.35 , that is formed with carbon participation from oil vacuum. In more deeper layers beside ε-Ti 2 N TiC 0.14 N 0.77 is present. Effect of carbon diffusion from substrate to forming coating is stated. Gradient of element concentrations in the substrate-coating interface causes recrystallization of austenite

  14. Effect of aging on the tribological and mechanical properties of a high-nitrogen stainless austenitic steel

    International Nuclear Information System (INIS)

    Korshunov, L.G.; Chernenko, N.L.; Tereshchenko, N.A.; Uvarov, A.I.

    2005-01-01

    The effect of aging, associated with predominant precipitation of vanadium nitrides (VN), on tribological and mechanical properties of austenitic steel 10Kh18AG18N5MF hardened from 1100 Deg C is studied. Metallographic, X-ray diffraction and electron microscopical methods are used to study structural transformations proceeding in the steel on aging as well as on friction loading under conditions of dry slipping friction in steel-abrasive and steel-steel pairs. It is shown that the aging at temperatures of 600-700 Deg C resulting in a considerable increase of strength properties of the steel demonstrates a relatively weak positive effect on steel resistance to abrasive and adhesive wear. It is stated that the use of aging by continuous mechanism permits attaining favourable mechanical and tribological properties in vanadium-alloying nitrogen-bearing austenitic steels [ru

  15. Effects of Cr2N Precipitation on the Antibacterial Properties of AISI 430 Stainless Steel

    Directory of Open Access Journals (Sweden)

    Je-Kang Du

    2016-03-01

    Full Text Available Based on their mechanical properties and good corrosion resistance, some commercial Ni-Cr stainless steels have been widely applied as biomaterials, including the austenitic 304 stainless steel, the austenitic 316 stainless steel, the duplex 2205 stainless steel, and the ferritic 430 stainless steel. In order to reduce the occurrence of infections resulting from biomaterial implants, instruments, and medical devices, Cu2+ and Ag2+ ions have been added onto biomaterials for increasing the antibacterial properties, but they are known to damage biofilm. The occurrence of nanoparticles can also improve the antibacterial properties of biomaterials through various methods. In this study, we used Escherichia coli and analyzed the microstructures of American Iron and Steel Institute (AISI 430 stainless steel with a 0.18 mass % N alloy element. During a lower temperature aging, the microstructure of the as-quenched specimen is essentially a ferrite and martensite duplex matrix with some Cr2N precipitates formed. Additionally, the antibacterial properties of the alloy for E. coli ranged from 3% to 60%, consistent with the presence of Cr2N precipitates. When aged at a lower temperature, which resulted in nano-Cr2N precipitation, the specimen possessed the highest antibacterial activity.

  16. Stainless austenitic steels strengthened due to reversible phase transformations and by ageing

    International Nuclear Information System (INIS)

    Sagaradze, V.V.; Kositsyna, I.I.; Ozhiganov, A.V.

    1981-01-01

    The effect of the reversible phase transformations, consisting in the conduction of the direct and reverse martensite transformations and aging, during which the intermetallide γ'-phase of the composition Ni 3 Ti is formed, on the streng-thening of alloys in the Fe-Cr-Ni-Ti system is considered. Stainless austenitic steels Kh12N12T3 and Kh12N14T3, which acquire high mechanical properties: σsub(0.2)=685-785 MPa, σsub(B)=1275 MPa, delta >= 20%, as a result of reversible phase transformations and aging, are suggested. After the reversible phase transformations and ageing the steels possess a high resistance to γ-α-transformation during cold treatment [ru

  17. Tribocorrosion behaviour of 08CH18N10T steel

    International Nuclear Information System (INIS)

    Kubecka, P.; Tvrdy, M.; Wenger, F.; Ponthiaux, P.

    2000-01-01

    Tribocorrosion of the 08CH18N10T austenitic stainless steel in a potassium sulphate solution was investigated with the help of pin-on-disk tribometer and polarisation curves method. The results indicate the occurrence of synergetic interactions between electrochemical and mechanical conditions: the damaging of the passive film by friction was pointed out, leading to an increase in the dissolution rate of the metal and simultaneously, the occurrence of electrochemical reactions (gas evolution, dissolution, passivation) was found to modify the tribological conditions (friction coefficient). (author)

  18. Experimental verification of the statistical theories of scaling factor effect in fatigue fracture of steel

    International Nuclear Information System (INIS)

    Svistun, R.P.; Babej, Yu.I.; Tkachenko, N.N.

    1976-01-01

    Statistical theories of the scale effect in the fatigue failure of 40KH18N9T, 10 and 20 steels have been verified. The theories are shown to be not invariably suitable for a satisfactory exlanation of the fatigue strength of the samples with respect to their dimensions. One of the main reasons for displaying the scale effect in the process of steel fatigue is the sample self-heating, i.e. a temperature factor which in many cases overlaps a statistical one

  19. Experimental verification of the statistical theories of scaling factor effect in fatigue fracture of steel

    Energy Technology Data Exchange (ETDEWEB)

    Svistun, R P; Babei, Yu I; Tkachenko, N N [AN Ukrainskoj SSR, Lvov. Fiziko-Mekhanicheskij Inst.; L' vovskij Lesotekhnicheskij Inst. (Ukrainian SSR))

    1976-01-01

    Statistical theories of the scale effect in the fatigue failure of 40KH18N9T, 10 and 20 steels have been verified. The theories are shown to be not invariably suitable for a satisfactory exlanation of the fatigue strength of the samples with respect to their dimensions. One of the main reasons for displaying the scale effect in the process of steel fatigue is the sample self-heating, i.e. a temperature factor which in many cases overlaps a statistical one.

  20. Ionic complexation of N 2O 4 by 18-crown-6

    Science.gov (United States)

    Ricard, S.; Audet, P.; Savoie, R.

    1988-08-01

    An ionic complex has been obtained from N 2O 4 in the presence of the macrocyclic ether 18-crown-6. This crystalline compound has been shown from its Raman spectrum to have the formula NO +·crown·H(NO 3) 2-, with the nitrosonium ion closely associated with the crown ether rather than with the hydrogen dinitrate accompanying ion. This adduct decomposes readily in moist air to give the known complex (HNO 3·H 2O) 2·crown.

  1. Synthesis of [18F]-N-3-fluoro-propyl-2β-carbomethoxy-3β-(4-iodophenyl) nortropane ([18F]-FP-β-CIT)

    International Nuclear Information System (INIS)

    Fang Ping; Chen Zhengping; Lin Yansong; Zhou Xian; Du Yikui

    2001-01-01

    The ligand of N-(3-fluoro-propyl)-2β-carbomethoxy-3β-(4'-iodophenyl) nortropane (FP-β-CIT) and mesylate precursor were synthesized by hydrolysis of cocaine, followed by dehydration, esterification, Grignard reaction, N-demethylation, iodination, N-alkylation with 3-bromo-propanol and methyl-sulfonyl. Finally, 18 F-FP-β-CIT was prepared by nucleophilic fluorination of the mesylate with K 18 F/K 2.2.2 (Kryptofix). The labelling yield of 18 F-FP-β-CIT is 25%-30%. The total radiochemical yield of this compound, calculated from the end of bombardment (EOB) with decay correction, is 10%-12% with a synthesis time of 100-110 min. The radiochemical purity of 18 F-FP-β-CIT is greater than 90%, and this compound in aqueous solution is also stable for more than 4 hours at room temperature. It is stable enough for clinical study

  2. N-(N-benzylpiperidin-4-yl)-2-[18F]fluorobenzamide: A potential ligand for PET imaging of σ receptors

    International Nuclear Information System (INIS)

    Shiue Chyngyann; Shiue, Grace G.; Zhang, Sue X.; Wilder, Susan; Greenberg, Joel H.; Benard, Francois; Wortman, Jeffrey A.; Alavi, Abass A.

    1997-01-01

    Four nitro- and fluorobenzamides (1-4) have been synthesized in good yields from nitro- and fluoro-substituted benzoyl chloride with 4-amino-1-benzylpiperidine. In vitro studies showed that these compounds have high affinities to σ receptors. N-(N-Benzylpiperidin-4-yl)-2-fluorobenzamide (3), in particular, bound to σ receptors with high affinity (K i = 3.4 nM, guinea pig brain membranes) and high selectivity (σ-2/σ-1 = 120). It was, therefore, labeled with 18 F and evaluated as a σ receptor radioligand. N-(N-Benzylpiperidin-4-yl)-2-[ 18 F]fluorobenzamide (3a) was synthesized in one step by nucleophilic substitution of the 2-nitro precursor (1) with [ 18 F]fluoride in DMSO at 140 deg. C for 20 min followed by purification with HPLC in 4-10% yield (decay corrected). The synthesis time was 90 min and the specific activity was 0.4-1.0 Ci/μmol. Tissue distribution in mice revealed that the uptakes of 3a in the brain, heart, liver, lungs, spleen, kidneys and small intestine were high, and the radioactivity in these organs remained constant from 60 to 120 min post-injection. The radioactivity in the bone did not significantly increase, suggesting in vivo defluorination may not be the major route of metabolism of 3a in mice. Blocking studies with haloperidol in rats indicated that the uptake of compound 3a in the rat brain was selective to haloperidol-sensitive σ sites. These results suggest that compound 3a is a potent σ receptor radioligand and may be a potential ligand for PET imaging of σ receptors in humans

  3. Application of experiment planning during investigation of cementation process in solid carburizers

    International Nuclear Information System (INIS)

    Lisenkov, A.N.; Denisov, V.M.; Prigozhina, E.L.

    1981-01-01

    A mathematical model of cementation process in solid carburizirs is obtained, the most effective contents of carburizers are chosen. Specimens are produced out of St20, 12KhN3A, 40Kh13, KhVG steels. It is shown that specimens of St20 and 12KhN3A steels have the higher depth of cementated layer, specimens made of 40Kh13 and KhVG steels-the lower depth. It is shown that the quality of cementated layer structure at recommended regimes improved, cementated layer depth for low-carbon steels changed a little and for tool steels increased infficiently: for KhVG steel in 2-3 times for 40Kh13 steel in 1.5-2.5 times

  4. Synthesis of n.c.a. 18F-fluorinated NMDA- and D4-receptor ligands via [18F]fluorobenzenes

    International Nuclear Information System (INIS)

    Ludwig, T.

    2005-11-01

    In this thesis new strategies were developed and evaluated for the no-carrier-added (n.c.a.) 18 F-labelling of receptor ligands as radiodiagnostics for characterization of brain receptors using positron-emission-tomography (PET). Special emphasis was placed on the synthesis of n.c.a. (±)-3-(4-hydroxy-4-(4-[ 18 F]fluorophenyl)-piperidin-l-yl)chroman-4,7-diol, a ligand with high affinity for the NR2B subtype of NMDA receptors and n.c.a. (3-(4-[ 18 F]fluorphenoxy)propyl)-(2-(4-tolylphenoxy)ethyl)amine ([ 18 F]FPTEA) a dopamine D 4 receptor ligand. In order to synthesize n.c.a. (±)-3-(4-hydroxy-4-(4-[ 18 F]fluorophenyl)-piperidin-l-yl)chroman-4,7-diol the 18 F-fluoroarylation method via metallorganic intermediates was modified and improved. The suitability of the organometallic 18 F-fluoroarylation agents was proven with several model compounds. High radiochemical yields of 20-30% were obtained also with piperidinone-derivatives. The preparation of a suitable precursor for the synthesis of the NMDA receptor ligand, however, could not be achieved by synthesis of appropriate 1,3-dioxolane protected piperidinone derivatives. Further, the synthesis of n.c.a. ([ 18 F]fluoroaryloxy)alkylamines via n.c.a. 4-[ 18 F]fluorophenol was developed and evaluated. The synthesis of n.c.a. [ 18 F]fluoroarylethers with corresponding model compounds was optimized and led to a radiochemical yield of 25-60%, depending on the alkylhalide used. The preparation of n.c.a. 1-(3-bromopropoxy)-4-[ 18 F]fluorobenzene proved advantageous in comparison to direct use of 4-[ 18 ]fluorophenol for coupling with a corresponding N-protected precursor for the synthesis of n.c.a. [ 18 F]FPTEA. With regard to the radiochemical yields and the loss of activity during the synthesis and isolation of n.c.a. 4-[ 18 F]fluorophenol and n.c.a. 1-(3-bromopropoxy)-4-[ 18 F]fluorobenzene, [ 18 F]FPTEA was obtained by reaction with 2-(4-tolyloxy)ethylamine in radiochemical yields of about 25-30% in ethanol or 2-butanone

  5. Influence of chemical heterogeneity of solid solutions on brittleness in chromium steels

    International Nuclear Information System (INIS)

    Madyanov, S.A.; Sedov, V.K.; Apaev, B.A.

    1985-01-01

    The role of chemical heterogeneity of solid solutions in formation of mechanical properties of Kh09, Kh15, Kh20, Kh19N2G5T chromium steels has been investigated. It is established that besides the known regioA of chemical heterogeneity in the vicinity of 475 deg C exists a high-temperature region (1000-1050 deg C), where maximum heteroge=- neity of chromium distribution in solid solution, is observed. Both types of chemical heterogeneity cause essential hardening of alloys, which becomes apparent in abrupt change of capability to microplastic deformation The mechanism of occurrence of the given temper brittleness consists in carbon diffusion into microvolunes enriched in carbide-forming elements

  6. Design of the WWER-440 pressurizer

    International Nuclear Information System (INIS)

    Bednarek, L.

    1978-01-01

    The main specifications are presented of a pressurizer for the WWER-440 reactor as are factors securing operating reliability and the required life of the equipment. Ferritic-pearlite steel 22K is the basic material for the manufacture of the shell, support and couplings. The internal parts and the heads are manufactured from the 08KH18N10T chromium-nickel austenitic steel, the bolts and nuts of manholes from chromium-molybdenum steels 25KH1MF and 25KH2MFA. Quality testing of basic materials and quality control during the process of manufacture are briefly described. (Z.M.)

  7. Corrosion-electrochemical behavior of metals in alkali solutions

    International Nuclear Information System (INIS)

    Levin, V.A.; Levina, E.Eh.

    1995-01-01

    Results of an investigation into corrosion-electrochemical behaviour of 12Kh18N10T, 10Kh17N13M2T, 08Kh21N6M2T and 15Kh25T steels, 06KhN28MDT and KhN78T alloys as well as NP-2 nickel in sodium, potassium and lithium hydroxide solutions at 95-180 deg C temperatures are considered. It is ascertained, that anode polarization curves of all metals irrespective of hydroxide nature, concentration, temperature, presence of chloride and chlorate additions, are of identic character. The movement of anode polarization curves in the direction of lower current of hydroxide type in NaOH-KOH-LiOH series, temperature and solution concentration reduction at other equal terms. 12 refs.; 6 figs

  8. The effect of chromium diffusion redistribution on wear resistance of carburized 3Kh13 steel

    International Nuclear Information System (INIS)

    Shcherbedinskij, G.V.; Shumakov, A.I.; Zemskij, S.V.; Pereverzev, V.M.

    1977-01-01

    The redistribution of chromium in steel 3Kh13 on carburization in a high-activity carburizer and the wear-resistance of the steel have been investigated. Surface layers with an increased chromium concentration show the highest wear-resistance. The chromium content in the surface layer increases due to its diffusion from the interior. The distribution of carbon and chromium in the carburized layers has been studied with the aid of the radioactive isotope 14 C by the method of layer-by-layer spectral analysis on a vacuum quantometer, layer-by-layer chemical and X-ray structure analysis. The composition of the carbides has been determined by physicochemical analysis. It has been established that the carburized layer can be divided into four zones with respect to its phase composition: first zone - hematite and spinal with 0.5-2.0% C; second zone - solid carbides (Fe,Cr) 7 C 3 ; up to 5% C; third zone - globular carbides in a troostite matrix (Cr,Fe) 7 C 3 and Cr 23 C 6 ; up to 3.5% C; fourth, transitional, zone - troostite carbide mixture Cr 23 C 6 ; up to 1% C. The chromium diffusion in the carburized layer is faster than in the initial austenite. The chromium counterdiffusion is due to the development of a zone of solid carbides M 7 C 3

  9. 4- 18F]fluoroarylalkylethers via an improved synthesis of n.c.a. 4- 18F]fluorophenol

    International Nuclear Information System (INIS)

    Ludwig, Thomas; Ermert, Johannes; Coenen, Heinz H.

    2002-01-01

    This paper describes the improved synthesis of n.c.a. 4- 18 F]fluorophenol for the preparation of 18 F-labeled alkylarylethers. Nucleophilic fluorination of substituted benzophenone derivatives yielded n.c.a. 4- 18 F]fluoro-4'-substituted benzophenones with 80- 90 % RCY, which were converted to benzoic acid phenylesters by treatment with peracetic acid. Strong electron-withdrawing substituents like nitro, cyano and trifluoromethyl favor a fluorophenyl-to-oxygen migration resulting in the formation of corresponding benzoic acid fluorophenylesters. N.c.a. 18 F]fluorophenol is almost quantitatively formed after hydrolysis and can easily be converted with alkylhalides into n.c.a. 18 F]fluoroarylalkylethers

  10. Corrosion resistance of chromium-nickel steel containing rare earths

    International Nuclear Information System (INIS)

    Asatiani, G.N.; Mandzhgaladze, S.N.; Tavadze, L.F.; Chuvatina, S.N.; Saginadze, D.I.

    1983-01-01

    Effect of additional out-of-furnace treatment with complex alloy (foundry alloy) calcite-silicon-magnesium-rare earth metal on corrosion resistance of the 03Kh18N20M3D3C3B steel has been studied. It is shown that introduction of low additions of rare earths improves its corrosion resistance improves its corrosion resistance in agressive media (in 70% - sulfuric acid) in the range of transition from active to passive state. Effect of additional introduction of rare earth metals is not considerable, if potential of steel corrosion is in the range of stable passive state (32% - sulfuric acid). Additional out-of-furnace treatment with complex foundry alloy, containing rare earth metals, provides a possibility to use a steel with a lower content of Cr, Ni, Mo, than in conventional acid-resistant steels in highly agressive media

  11. Effect of high-temperature exposure on the mechanical properties of 18Cr–8Ni–W–Nb–V–N stainless steel

    International Nuclear Information System (INIS)

    Nikulin, I.; Kipelova, A.; Kaibyshev, R.

    2012-01-01

    Highlights: ► Niobium stabilized 18Cr–8Ni austenitic steel was subjected to long-time aging. ► The main phases precipitated during aging are Z-phase and Laves-phase. ► Intragranular phases and solid solution are responsible for tensile strength. ► Intergranular particles affect impact toughness. - Abstract: The change in the mechanical properties of 18Cr–8Ni–W–Nb–V–N austenitic stainless steel due to aging was investigated at room temperature and 650 °C. It was shown that long-term aging decreases strength characteristics despite increasing hardness. The impact toughness decreases from 255 J/cm 2 for an un-aged steel to 135 J/cm 2 for the steel aged for 3000 h. However, evidence of ductile fracture was found even after long-term aging. This study suggests that the reduction in impact toughness occurs due to the precipitation of Z-phase and Laves-phase particles at the grain boundaries. The degradation of impact toughness and mechanical properties with aging is discussed in terms of microstructure evolution, secondary phase precipitations and fracture mechanisms.

  12. KH in Paraffin - KH(P): A Useful Base for Organic Synthesis

    Science.gov (United States)

    Taber, Douglass F.; Nelson, Christopher G.

    2011-01-01

    The preparation of KH as a one:one homogenate with paraffin, termed KH(P), is reported. KH(P), a solid at room temperature, is stable without special handling. On suspension in THF with a phosphonium salt, KH(P) rapidly generates the ylide. Wittig condensation with aromatic, aliphatic and α, β-unsaturated aldehydes proceeds with high Z-selectivity. KH(P) should be a generally useful base for organic synthesis. PMID:17081034

  13. Quality of the KhN73MBTYu alloy after electroslag remelting and vacuum arc remelting

    International Nuclear Information System (INIS)

    Shelgaeva, A.V.; Krichevets, M.I.; Shinkina, N.S.; Komissarov, A.I.

    1978-01-01

    The structure and properties of the heat-resisting KhN73MBTYu alloy are investigated after electroslag remelting (ESR) and vacuum arc (VAR) remelting in commercial furnaces. The complex investigations of the casted metal were carried out by modern methods along with the standard acceptance tests, and a number of service properties were determined. It is established that the ESR metal contains magnesium and has the reduced sulphur concentration; the alloy has more fine-grained structure at high isotropy of the properties at room and operating temperatures; higher endurance is achieved under reversal rotational bending; no laminated fractures are observed. According to the basic quality factors the ESR metal satisfies all requirements for the VAR metal. Due to exclusion of strippling of ESR electrodes and ingots the yield of steel forgings increases by 20-25% and the prime cost decreases in comparison with the industrial production of VAR metal

  14. Welding wires for high-tensile steels

    International Nuclear Information System (INIS)

    Laz'ko, V.E.; Starova, L.L.; Koval'chuk, V.G.; Maksimovich, T.L.; Labzina, I.E.; Yadrov, V.M.

    1993-01-01

    Strength of welded joints in arc welding of high-tensile steels of mean and high thickness by welding wires is equal to approximately 1300 MPa in thermohardened state and approximately 600 MPa without heat treatment. Sv-15Kh2NMTsRA-VI (EhK44-VI) -Sv-30Kh2NMTsRA-VI (EkK47-VI) welding wires are suggested for welding of medium-carbon alloyed steels. These wires provide monotonous growth of ultimate strength of weld metal in 1250-1900 MPa range with increase of C content in heat-treated state

  15. N-(N-benzylpiperidin-4-yl)-2-[{sup 18}F]fluorobenzamide: A potential ligand for PET imaging of {sigma} receptors

    Energy Technology Data Exchange (ETDEWEB)

    Chyngyann, Shiue; Shiue, Grace G; Zhang, Sue X; Wilder, Susan; Greenberg, Joel H; Benard, Francois; Wortman, Jeffrey A; Alavi, Abass A

    1997-10-01

    Four nitro- and fluorobenzamides (1-4) have been synthesized in good yields from nitro- and fluoro-substituted benzoyl chloride with 4-amino-1-benzylpiperidine. In vitro studies showed that these compounds have high affinities to {sigma} receptors. N-(N-Benzylpiperidin-4-yl)-2-fluorobenzamide (3), in particular, bound to {sigma} receptors with high affinity (K{sub i} = 3.4 nM, guinea pig brain membranes) and high selectivity ({sigma}-2/{sigma}-1 = 120). It was, therefore, labeled with {sup 18}F and evaluated as a {sigma} receptor radioligand. N-(N-Benzylpiperidin-4-yl)-2-[{sup 18}F]fluorobenzamide (3a) was synthesized in one step by nucleophilic substitution of the 2-nitro precursor (1) with [{sup 18}F]fluoride in DMSO at 140 deg. C for 20 min followed by purification with HPLC in 4-10% yield (decay corrected). The synthesis time was 90 min and the specific activity was 0.4-1.0 Ci/{mu}mol. Tissue distribution in mice revealed that the uptakes of 3a in the brain, heart, liver, lungs, spleen, kidneys and small intestine were high, and the radioactivity in these organs remained constant from 60 to 120 min post-injection. The radioactivity in the bone did not significantly increase, suggesting in vivo defluorination may not be the major route of metabolism of 3a in mice. Blocking studies with haloperidol in rats indicated that the uptake of compound 3a in the rat brain was selective to haloperidol-sensitive {sigma} sites. These results suggest that compound 3a is a potent {sigma} receptor radioligand and may be a potential ligand for PET imaging of {sigma} receptors in humans.

  16. On the adsorption-induced fatigue of structural steels in the presence of alcohols

    International Nuclear Information System (INIS)

    Loboiko, V.I.; Karpenko, G.V.; Vasilenko, I.I.

    1976-01-01

    The purpose of the work was to study he effect of anhydrous alcohols on the cyclic fatigue of steels in the absence of contact of the alcohol with atmospheric moisture during the testing process. A vacuum was created in the operating space and then the vacuum annealing was carried out in a bath with the sample and through metal vacuum connection the bath was filled with anhydrous alcohol. Studies were made on several construction steels (20Kh, 40Kh, 50Kh, and ShKh15); steels 40Kh, 50Kh, and ShKh15 were quenched from 840-860 0 C in oil and then tempered at 200 0 C (2 h), steel 20Kh was studied in the as-received state. It was shown that with increase in the carbon content of steel with a martensite structure, the decrease in strength in the presence of anhydrous alcohol was greater than in dry air. Experiments showed that anhydrous alcohol causes an adsorption decrease in the strength both of samples with preliminarily formed cracks and V-shaped stress concentrators and of smooth samples. The greatest adsorption effect of alcohols in our case, as in static fatigue, was observed in samples with cracks. A dependence was shown between the length of the carbon chain and the fatigue limit. This dependence indicates the monotone nature of the decrease in the fatigue limit with transfer from methyl to butyl and then to octyl alcohol

  17. Fracture of ledeburitic steel during hot plastic deformation

    International Nuclear Information System (INIS)

    Nikitin, V.P.; Borisov, Yu.A.; Bulat, S.I.; Zajtsev, V.V.

    1977-01-01

    The mechanisms of the high-temperature failure of high-carbon chromium Kh6F1, Kh6T2 and Kh6VF steels and a possibility to avoid their overheating have been investigated. At 1190 deg C and over the failure occurs along boundaries of grains at points of formation of the initial portions of the liquid phase as carbides are dissolved. If after a holding at 1190-1210 deg C the steels are cooled to 1120-1150 deg C and held for a sufficiently long time, secondary carbides are formed in the eutectic areas and, if the steels are deformed, the discontinuities present a rounded shape. Holding of an overheated steel at 1120-1150 deg C ensures its satisfactory workability in rolling. By choosing adequate overheating and subsequent slight cooling conditions, it is possible not only to retain, but even to improve the plasticity of carbide high-carbon steels. The results of laboratory tests have been confirmed under industrial conditions

  18. Optimum conditions for aging of stainless maraging steels

    International Nuclear Information System (INIS)

    Mironenko, P.A.; Krasnikova, S.I.; Drobot, A.V.

    1980-01-01

    Aging kinetics of two 0Kh11N10M2T type steels in which 3 % Mo (steel 1), and 3 % Mo and 11 % Co (steel 2) had been additionally introduced instead of titanium were investigated. Electron microscopy and X-ray methods were used. It was ascertained that the process of steel aging proceeded in 3 stages. Steel 2 was hardened more intensively during the aging, had a higher degree of hardness and strength after the aging, weakened more slowly if overaged than steel 1. The intermetallide hcp-phase Fe 2 Mo was the hardening phase on steels extended aging. Optimum combination of impact strength and strength was was achieved using two-stage aging: the first stage - maximum strength aging was achieved, the second stage - aging at minimum temperatures of two-phase α+γ region

  19. Aging precipitation behavior and its influence on mechanical properties of Mn18Cr18N austenitic stainless steel

    Science.gov (United States)

    Qin, Fengming; Li, Yajie; He, Wenwu; Zhao, Xiaodong; Chen, Huiqin

    2017-11-01

    The aging precipitation behavior in Mn18Cr18N austenitic stainless steel was investigated at temperatures from 600 °C to 900 °C. During isothermal aging treatment, the primary precipitate was Cr2N with a = 0.478 nm and c = 0.444 nm, and it preferentially nucleates along initial grain boundaries and gradually grows towards the interior of grains in discontinuous cellular way. Meanwhile, a small amount of granular face-centred cubic M23C6 with a = 1.066 nm also were observed, which mainly form along grain boundaries. The effect of these precipitates on mechanical properties of the alloy was studied. It was found that precipitates result in degeneration of the matrix hardness. Meanwhile, the SEM morphologies of aged tensile sample show that the brittle fracture predominates during deformation, i.e. the fracture mode transforms from intergranular fracture to transgranular fracture with the increasing of aging time. Compared with the solution-treated sample, the strength of the aged tensile samples slightly decreases and plasticity remarkably deteriorates.

  20. Evaluation of rolling contact fatigue of induction heated 13Cr-2Ni-2Mo Stainless steel bar with Si3N4-ball

    Science.gov (United States)

    Yadoiwa, Ariyasu; Mizobe, Koshiro; Kida, Katsuyuki

    2018-03-01

    13Cr % martensitic stainless steels were used in various industry, because they have excellent corrosion resistance and high hardness among other stainless steels. They are also expected as a bearing material, however, the research on rolling contact fatigue (RCF) is not enough. In this study, 13Cr-2Ni-2Mo stainless steels were quenched by induction heating and their RCF lives were evaluated. A Si3N4-ball was used in order to apply higher stress (Pmax = 5.6 GPa) than our previous tests (Pmax=5.3 GPa), in a single-ball RCF testing machine. It was found that the basic life (L10) was 2.20×106 cycles and Median life (L50) was 6.04×106 cycles. In addition, Weibull modulus became higher than the previous tests.

  1. Interaction of steel, titanium and zirconium with melted chlorides containing copper and zinc

    International Nuclear Information System (INIS)

    Ozeryanaya, I.N.; Manukhina, T.I.; Shibanov, B.S.

    1976-01-01

    Cu and Zn coatings were obtained by contact displacement of their molten chlorides. Cu was deposited on Kh18N10T stainless steel, and Zn was deposited on Ti or Zr at 400-550 0 . Cu was displaced from the electrolyte by all components in the steel. A smooth coating exhibited high adhesion. According to metallography there was a transition layer of a Ni-Cr solid solution between the surface Cu layer and steel. With electronegetiol Ti and Zr, contact deposition of Zn or Cu from chloride melts was possible. The coatings were multilayer and exhibited adequate adhesion. The coating consisted of an intermetallic compound of Ti or Zr with Zn

  2. Effect of preliminary neutron irradiation on helium blistering of 0Kh16N15M3B steel

    International Nuclear Information System (INIS)

    Chernov, I.I.; Kalin, B.A.; Skorov, D.M.; Shishkin, G.N.; Ivanov, M.V.

    1982-01-01

    The method of electron microscopy has been applied to investigate the effect of preliminary neutron irradiation on the OKh16N15M3B steel blistering under irradiation by 20 keV helium ions with (1-10)x10 21 ion/m 2 doses at the temperature below 373 K. It is shown that neutron irradiation shifts critical doses of blister formation and intense scaling towards higher doses. But after the incubation period the erosion of steel preliminary neutron irradiated grows with the increase of helium ion dose above 7x10 21 ion/m 2 . Short-term heating of neutron irradiated samples during 15 min at 1173 K does not practically affect the beginning of intense scaling of the surface

  3. Account of low temperature hardening in calculation of permissible stresses

    International Nuclear Information System (INIS)

    Novikov, N.V.; Ul'yanenko, A.P.; Gorodyskij, N.I.

    1980-01-01

    Suggested is a calculation scheme of permissible stresses with the account of temperature hardening for steels and alloys, the dependences of strength, plasticity and rupture work of which on cooling temperature do not have threshold changes in a wide range of low temperatures (from 300 to 4.2 K). Application of the suggested scheme is considered on the example of 12Kh18N10T austenitic chromium-nickel steel

  4. Analytical description of changes in the magnetic states of chromium-nickel steel under uniaxial elastic deformation

    Science.gov (United States)

    Gorkunov, E. S.; Yakushenko, E. I.; Zadvorkin, S. M.; Mushnikov, A. N.

    2017-12-01

    Dependences of magnetization and magnetic permeability of the 15KhN4D structural steel on the value of uniaxial stresses and magnetic field strength are obtained. A polynomial approximation fairly accurately describing the observed changes is proposed on the basis of experimental data.

  5. Study of effect of austenite prehistory of 03Ch20N16AG6 steel on it structure and properties

    Energy Technology Data Exchange (ETDEWEB)

    Demchuk, I S; Krakhmalev, V I; Manninen, A I [Leningradskij Politekhnicheskij Inst. (USSR)

    1981-01-01

    Effect of preliminary cold working and different procedures of thermal treatment on structure and mechanical properties of stable austenite of 03Kh20N16AG6 steel is found out. It is shown that the degree of defectability of initial austenite structure predetermines the further deformation behaviour of the steel (level of strength characteristics, plasticity storage, hardening degree etc.) in the wide temperature range. Close connection of structural changes with properties should determine the choice of preliminary treatment of stable austenitic steel as applied to concrete condition of operation.

  6. Quality of structural steel melted by single-slag process

    International Nuclear Information System (INIS)

    Levin, A.M.; Andreev, V.I.; Monastyrskij, A.V.; Drozdova, M.F.; Pashchenko, V.E.; Orzhekh, M.B.

    1982-01-01

    The 40Kh and 12KhN3A steels were used to compare the quality of the metal manufactured according to several variants of a single-slag process with the metal of a conventional melting technology. Investigation results show, that a single-slag process metal has higher sulfides and oxides contents as well as an increased anisotropy of mechanical properties while its tendency to flake formation is weaker due to a less degree of gas saturation. It is marked that anisotropy in the properties and a sulfide content may be decreased by out-of-furnace treatment of steels

  7. Vanishing of T sub c and appearance of quantum paraelectricity in KD sub 2 PO sub 4 and KH sub 2 PO sub 4 under high pressure

    CERN Document Server

    Endo, S; Tokunaga, M

    2002-01-01

    The temperature dependences of the dielectric constants of the hydrogen-bond ferroelectrics KH sub 2 PO sub 4 (KDP) and KD sub 2 PO sub 4 (DKDP) were measured under high hydrostatic pressure. Their ferroelectric transition temperatures T sub c monotonically decreased with increasing pressure and the ferroelectric state vanished at p sub c : 1.7 GPa for KDP and 6.1 GPa for DKDP. On the other hand, the Curie constant remained finite at p sub c , which indicates that the ferroelectric phase transition at high pressure is of displacive type. At pressures around p sub c , quantum paraelectricity was observed in KDP and DKDP.

  8. Cold-rolled sheets production of stainless martensite-ageing steel smelted by vacuum arc and electroslag techniques

    Energy Technology Data Exchange (ETDEWEB)

    Rivkin, A A; Grishkov, A I; Suslin, A P; Nesterenko, A A; Lola, V N [Tsentral' nyj Nauchno-Issledovatel' skij Inst. Chernoj Metallurgii, Moscow (USSR)

    1975-05-01

    In cooperation with a number of metallurgical works the production of a high strength sheet stainless maraging steel EHP678 (000KH11N10M2T) has been tested by rolling cylindrical ingots of vacuum arc smelting at the blooming (the mass of rough ingots was 5.1 to 6.0 t, that of cleaned ingots - 3.8 to 5.1 t) or rectangular ingots of electroslag smelting (13 t) at the slabbing. The recommended regimes of heating and deformation are much similar to those used for the steel-KH18N10T. The output of valid cold-rolled sheets proved to be rather low (0.24 t/t for the vacuum arc smelting and 0.30 t/t for the electroslag smelting) mainly due to the losses on cleaning and a considerable portion of wrong-size slabs. The data are presented on the steel-EHP678 properties after various heat treatments. For the production of wide cold-rolled sheets of the steel EHP678 it is recommended to use steelmaking procedure with electroslag smelting including open-hearth melting in arc furnaces, rolling of ingots at the slabbing with heating up to 1260-1280 deg C (hold-up of 4.5 to 5 hrs); electroslag smelting for rectangular section slabs, rolling of ingots of electroslag smelting at the slabbing with their heating up to 1250 deg C (hold-up of 5.5 to 6 hrs), rolling at the 1680-type mill with heating up to 1250-1260 deg C (hold-up of 4 to 4.5 hrs ensuring the rolling temperature after a rough group not below 1100 deg C), quenching of hot-rolled sheets heating up to 920-940 deg C (hold-up of 3 to 3.5 min/mm), shot peening of sheets for descaling (provided the respective equipment is available) with a subsequent short-time pickling in an acid solution and cold rolling with a summary deformation of 35 to 45 %. The steelmaking with the electroslag smelting is much more profitable as regards to the fine technology of number of the main procedures, convenient cooperation of the works and a considerably greater output of the final products out of one ton of the steel produced.

  9. Electrochemical machining of internal built-up surfaces of large-sized vessels for nuclear power plants

    Energy Technology Data Exchange (ETDEWEB)

    Ryabchenko, N N; Pulin, V Ya [Vsesoyuznyj Proektno-Tekhnologicheskij Inst. Atomnogo Mashinostroeniya i Kotlostroeniya, Rostov-na-Donu (USSR)

    1977-01-01

    Electrochemical machining (ECM) has been employed for finishing of mechanically processed inner surfaces of large lateral parts of construction bodies with welded 0Kh18N10T steel overlayer. The finishing technology developed reduces the surface roughness from 10 mcm to the standard 2.5 mcm at the efficiency of machining of 2-4 m/sup 2/ per hour.

  10. Advantages of Stainless Steel Sieves as Support for Catalytic N2O Decomposition over K-doped Co3O4.

    Czech Academy of Sciences Publication Activity Database

    Klyushina, A.; Pacultová, K.; Krejčová, S.; Slowik, G.; Jirátová, Květa; Kovanda, F.; Ryczkowski, J.; Obalová, L.

    2015-01-01

    Roč. 257, Part 1 (2015), s. 2-10 ISSN 0920-5861. [AWPAC2014 - International Symposium on Air & Water Pollution Abatement Catalysis. Krakow, 01.09.2014-05.09.2014] R&D Projects: GA ČR GA14-13750S Institutional support: RVO:67985858 Keywords : N2O catalytic decomposition * Co3O4 * stainless steel support * potassium promoter * TiO2 support Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 4.312, year: 2015

  11. Automated synthesis of ["1"8F](2S,4R)-4-fluoroglutamine on a GE TRACERlab™ FX-N Pro module

    International Nuclear Information System (INIS)

    Zhang, Xiang; Basuli, Falguni; Shi, Zhen-Dan; Xu, Biying; Blackman, Burchelle; Choyke, Peter L.; Swenson, Rolf E.

    2016-01-01

    Glutamine (Gln) and its analogues may serve as imaging agents for tumor diagnosis using positron emission tomography (PET), especially for tumors with negative ["1"8F]FDG scan. We report the first automated synthesis of ["1"8F](2S,4R)-4-fluoroglutamine (["1"8F]FGln) on a GE TRACERlab™ FX-N Pro module. ["1"8F]FGln was obtained in 80±3 min with a radiochemical yield of 21±3% (n=5, uncorrected). The radiochemical purity was >98%, and optical purity 90±5%. The synthesis is highly reproducible with good chemical purity, radiochemical yield, and is suitable for translation to cGMP production. - Highlights: • The radiosynthesis of ["1"8F]fluoroglutamine was optimized with improved yield and purity. • Fully automated synthesis was established on a GE TRACERlab™ FX-N Pro module. • Radiochemical yield of 21±3% (uncorrected, n=5) was obtained with good reproducibility. • The automation could be easily adapted to cGMP production for routine clinical use.

  12. Identification of electron and hole traps in KH2PO4 crystals

    International Nuclear Information System (INIS)

    Garces, N. Y.; Stevens, K. T.; Halliburton, L. E.; Demos, S. G.; Radousky, H. B.; Zaitseva, N. P.

    2001-01-01

    Electron paramagnetic resonance (EPR) has been used to characterize a hole trap and several electron traps in single crystals of potassium dihydrogen phosphate (KH 2 PO 4 or KDP). The paramagnetic charge states of these centers are produced by ionizing radiation (e.g., x rays or a 266 nm beam from a pulsed Nd:YAG laser) and are stable for days and even weeks at room temperature. One center consists of a hole trapped on an oxygen ion adjacent to a silicon impurity located on a phosphorus site. This defect has a small, but easily observed, hyperfine interaction with the adjacent substitutional proton. The other centers are formed when an electron is trapped at an oxygen vacancy. These latter defects are best described as (PO 3 ) 2- molecular ions, where the primary phosphorus nucleus is responsible for a large hyperfine splitting (500--800 G in magnitude). Five EPR spectra representing variations of these oxygen vacancy centers are observed, with the differences being attributed to the relative position of a nearby cation vacancy, either a missing proton or potassium. An angular study of the EPR spectra, conducted at room temperature, provided principal values and principal directions for the g matrices and hyperfine matrices for the hole center and two of the electron centers

  13. Special Features of Induction Annealing of Friction Stir Welded Joints of Medium-Alloy Steels

    Science.gov (United States)

    Priymak, E. Yu.; Stepanchukova, A. V.; Bashirova, E. V.; Fot, A. P.; Firsova, N. V.

    2018-01-01

    Welded joints of medium-alloy steels XJY750 and 40KhN2MA are studied in the initial condition and after different variants of annealing. Special features of the phase transformations occurring in the welded steels are determined. Optimum modes of annealing are recommended for the studied welded joints of drill pipes, which provide a high level of mechanical properties including the case of impact loading.

  14. 4- {sup 18}F]fluoroarylalkylethers via an improved synthesis of n.c.a. 4- {sup 18}F]fluorophenol

    Energy Technology Data Exchange (ETDEWEB)

    Ludwig, Thomas; Ermert, Johannes E-mail: j.ermert@fz-juelich.de; Coenen, Heinz H

    2002-02-01

    This paper describes the improved synthesis of n.c.a. 4- {sup 18}F]fluorophenol for the preparation of {sup 18}F-labeled alkylarylethers. Nucleophilic fluorination of substituted benzophenone derivatives yielded n.c.a. 4- {sup 18}F]fluoro-4'-substituted benzophenones with 80- 90 % RCY, which were converted to benzoic acid phenylesters by treatment with peracetic acid. Strong electron-withdrawing substituents like nitro, cyano and trifluoromethyl favor a fluorophenyl-to-oxygen migration resulting in the formation of corresponding benzoic acid fluorophenylesters. N.c.a. {sup 18}F]fluorophenol is almost quantitatively formed after hydrolysis and can easily be converted with alkylhalides into n.c.a. {sup 18}F]fluoroarylalkylethers.

  15. Precipitation Kinetics of Cr2N in High Nitrogen Austenitic Stainless Steel

    Institute of Scientific and Technical Information of China (English)

    SHI Feng; WANG Li-jun; CUI Wen-fang; LIU Chun-ming

    2008-01-01

    The precipitation behavior of Cr2N during isothermal aging in the temperature range from 700℃to 950℃ in Fe-18Cr-12Mn-0.48N(in mass percent)high nitrogen austenitic stainless steel,including morphology and content of precipitate,was investigated using optical microscopy,scanning electron microscopy,and transmission electron microscopy.The isothermal precipitation kinetics curve of Cr2N and the corresponding precipitation activation energy were obtained.The results show that Cr2N phase precipitates in a cellular way and its morphology is transformed from initial granular precipitates to lamellar ones in the cell with increasing aging time.The nose temperature of Cr2N precipitation is about 800℃,with a corresponding incubation period of 30 min,and the ceiling temperature of Cr2N precipitation is 950℃.The diffusion activation energy of Cr2N precipitation is 296 kJ/mol.

  16. On the guanidine hydrochloride method for determination of oxygen-18 content in orthophosphate

    International Nuclear Information System (INIS)

    Li Wenjun; Gu Zhennan

    1985-01-01

    The guanidine hydrochloride method is an accurate and simple procedure for oxygen-18 determination in KH 2 PO 4 and Ba 3 (PO 4 ) 2 . The method is based on heating the samples with guanidine hydrochloride at 300 deg C. Two Oxygen atoms per molecule of KH 2 PO 4 or Ba 3 (PO 4 ) 2 are converted into CO 2 which is then analysed by a mass spectrometer of model MAT-CH5. Only 5 mg of KH 2 PO 4 or Ba 3 (PO 4 ) 2 is required for each determination and reproducibility of assays is better than +-1%. (Author)

  17. The MMP inhibitor (R)-2-(N-benzyl-4-(2-[18F]fluoroethoxy)phenylsulphonamido) -N-hydroxy-3-methylbutanamide: Improved precursor synthesis and fully automated radiosynthesis

    International Nuclear Information System (INIS)

    Wagner, Stefan; Faust, Andreas; Breyholz, Hans-Joerg; Schober, Otmar; Schaefers, Michael; Kopka, Klaus

    2011-01-01

    Summary: The CGS 25966 derivative (R)-2-(N-Benzyl-4-(2-[ 18 F]fluoroethoxy)phenyl-sulphonamido) -N-hydroxy-3-methylbutanamide [ 18 F]9 represents a very potent radiolabelled matrix metalloproteinase inhibitor. For first human PET studies it is mandatory to have a fully automated radiosynthesis and a straightforward precursor synthesis available. The realisation of both requirements is reported herein. In particular, the corresponding precursor 8 was obtained in a reliable 7 step synthesis with an overall chemical yield of 2.3%. Furthermore, the target compound [ 18 F]9 was prepared with a radiochemical yield of 14.8±3.9% (not corrected for decay).

  18. MLEP-Fail calibration for 1/8 inch thick cast plate of 17-4 steel.

    Energy Technology Data Exchange (ETDEWEB)

    Corona, Edmundo [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2018-02-01

    The purpose of the work presented in this memo was to calibrate the Sierra material model Multilinear Elastic-Plastic Hardening Model with Failure (MLEP-Fail) for 1/8 inch thick cast plate of 17-4 steel. The calibration approach is essentially the same as that recently used in a previous memo using data from smooth and notched tensile specimens. The notched specimens were manufactured with three notch radii R = 1=8, 1/32 and 1/64 inches. The dimensions of the smooth and notched specimens are given in the prints in Appendix A. Two cast plates, Plate 3 and Plate 4, with nominally identical properties were considered.

  19. Reliability and durability of the 12Kh1MF steel tubes of electroslag remelting and their welded joints

    International Nuclear Information System (INIS)

    Lanskaya, K.A.; Kulikova, L.V.; Mazel', R.E.; Khromchenko, F.A.; Strizhenova, V.F.

    1978-01-01

    Results of investigating the positive effect of electrolag remelting (ESR) on the properties of the base metal and welded joint of the 12Kh1MF steel steam pipes with the aim of increasing their durability up to 20,000 hrs, are presented. To estimate the quality and properties of tube billet metal, microstructure, content and nature of nonmetallic inclusions, content of gases, austenite grain size, austenite transformations during continuous cooling, metal ductility, mechanical properties at different temperatures and heat resisting properties, have been investigated. It is established, that the base metal in tubes of electroslag remelting possess higher heat resistance, while welded joints besides, have high deformability and resistance to brittle fracture

  20. Plasma nitriding of CA-6NM steel: effect of H2 + N2 gas mixtures in nitride layer formation for low N2 contents at 500 ºC

    Directory of Open Access Journals (Sweden)

    Angela Nardelli Allenstein

    2010-12-01

    Full Text Available This work aims to characterize the phases, thickness, hardness and hardness profiles of the nitride layers formed on the CA-6NM martensitic stainless steel which was plasma nitrided in gas mixtures containing different nitrogen amounts. Nitriding was performed at 500 ºC temperature, and 532 Pa (4 Torr pressure, for gas mixtures of 5% N2 + 95% H2, 10% N2 + 90% H2, and 20% N2 + 80% H2, and 2 hours nitriding time. A 6 hours nitriding time condition for gas mixture of 5% N2 + 95% H2 was also studied. Nitrided samples results were compared with non-nitrided condition. Thickness and microstructure of the nitrided layers were characterized by optical microscopy (OM, using Villela and Nital etchants, and the phases were identified by X-ray diffraction. Hardness profiles and hardness measured on surface steel were determined using Vickers hardness and nanoindentation tester, respectively. It was verified that nitrided layer produced in CA-6NM martensitc stainless steel is constituted of compound layer, being that formation of the diffusion zone was not observed for the studied conditions. The higher the nitrogen amounts in gas mixture the higher is the thickness of the nitrided layer and the probability to form different nitride phases, in the case γ'-Fe4N, ε-Fe2-3N and CrN phases. Intrinsic hardness of the nitrided layers produced in the CA-6NM stainless steel is about 12-14 GPa (~1200-1400 HV.

  1. Cooling intensification during quenching of power plant components - the way to increase reliability

    International Nuclear Information System (INIS)

    Borisov, I.A.

    1989-01-01

    To enchance the complex of mechanical properties and to increase operation time of large components of power facilities, regimes of accelerated cooling are developed. Results of heat treatment with accelerated cooling of turbine rotor of steel 26KhN3M2FAA, disks of turbine welded rotor of steel 20KhN2MFAA, components of steel 35KhN3MFA, are given. Special steels with carbon content less than 0.30% for details of power machine-building are developed

  2. Roentgenoelectronic investigation into oxidation of iron-chromium and iron-chromium-nickel alloys

    International Nuclear Information System (INIS)

    Akimov, A.G.; Rozenfel'd, I.L.; Kazanskij, L.P.; Machavariani, G.V.

    1978-01-01

    Kinetics of iron-chromium and iron-chromium-nickel alloy oxidation (of the Kh13 and Kh18N10T steels) in oxygen was investigated using X-ray electron spectroscopy. It was found that according to X-ray electron spectra chromium oxidation kinetics in the iron-chromium alloy differs significantly from oxidation kinetics of chromium pattern. Layer by layer X-ray electron analysis showed that chromium is subjected to a deeper oxidation as compared to iron, and accordingly, Cr 2 O 3 layer with pure iron impregnations is placed between the layer of mixed oxide (Fe 3 O 4 +Cr 2 O 3 ) and metal. A model of the iron-chromium alloy surface is suggested. The mixed oxide composition on the steel surface is presented as spinel Fesub(2+x)Crsub(1-x)Osub(y)

  3. Microstructure and properties of thick nanocomposite TiN/Si{sub 3}N{sub 4} coatings on Vanadis 23 HS steel

    Energy Technology Data Exchange (ETDEWEB)

    Moskalewicz, Tomasz; Czyrska-Filemonowicz, Aleksandra [AGH Univ. of Science and Technology, Faculty of Metals Engineering and Industrial Computer Science, Krakow (Poland); Zimowski, Slawomir [AGH Univ. of Science and Technology, Faculty of Mechanical Engineering and Robotics, Krakow (Poland); Wendler, Bogdan; Progalskiy, Ivan [Lodz Univ. of Technology (Poland). Inst. of Materials Science and Engineering

    2015-07-15

    The microstructure and selected micro-mechanical properties of a 13.4 μm thick nanocomposite TiN/Si{sub 3}N{sub 4} coating deposited onto Vanadis 23 HS steel by a new gas pulsed magnetron sputtering technique were investigated. Scanning and transmission electron microscopy were employed to investigate the detailed microstructure of the coating. It was found that the coating exhibited a fully nanocrystalline structure and was composed of two zones: the outer zone with columnar structure and the inner one with equiaxed, fine columnar structure. Both zones consisted mainly of the δ-TiN nanocrystallites with a small amount of α-Si{sub 3}N{sub 4} and β-Si{sub 3}N{sub 4}. In order to increase coating adhesion to the substrate, a graded intermediate layer consisting of three different phases (pure Cr, CrN and Cr2N) was applied. The hardness of the as-deposited TiN/Si{sub 3}N{sub 4} coating was equal to 48 GPa, whereas it was equal to 40 GPa after annealing. The coatings exhibited very good adhesion to the underlying steel substrate.

  4. Synthesis of n.c.a. {sup 18}F-fluorinated NMDA- and D{sub 4}-receptor ligands via [{sup 18}F]fluorobenzenes; Traegerarme Synthese {sup 18}F-markierter, ausgewaehlter NMDA- und D{sub 4}-Rezeptorliganden durch Einsatz geeigneter [{sup 18}F]Fluorbenzolderivate

    Energy Technology Data Exchange (ETDEWEB)

    Ludwig, T

    2005-11-01

    In this thesis new strategies were developed and evaluated for the no-carrier-added (n.c.a.) {sup 18}F-labelling of receptor ligands as radiodiagnostics for characterization of brain receptors using positron-emission-tomography (PET). Special emphasis was placed on the synthesis of n.c.a. ({+-})-3-(4-hydroxy-4-(4-[{sup 18}F]fluorophenyl)-piperidin-l-yl)chroman-4,7-diol, a ligand with high affinity for the NR2B subtype of NMDA receptors and n.c.a. (3-(4-[{sup 18}F]fluorphenoxy)propyl)-(2-(4-tolylphenoxy)ethyl)amine ([{sup 18}F]FPTEA) a dopamine D{sub 4} receptor ligand. In order to synthesize n.c.a. ({+-})-3-(4-hydroxy-4-(4-[{sup 18}F]fluorophenyl)-piperidin-l-yl)chroman-4,7-diol the {sup 18}F-fluoroarylation method via metallorganic intermediates was modified and improved. The suitability of the organometallic {sup 18}F-fluoroarylation agents was proven with several model compounds. High radiochemical yields of 20-30% were obtained also with piperidinone-derivatives. The preparation of a suitable precursor for the synthesis of the NMDA receptor ligand, however, could not be achieved by synthesis of appropriate 1,3-dioxolane protected piperidinone derivatives. Further, the synthesis of n.c.a. ([{sup 18}F]fluoroaryloxy)alkylamines via n.c.a. 4-[{sup 18}F]fluorophenol was developed and evaluated. The synthesis of n.c.a. [{sup 18}F]fluoroarylethers with corresponding model compounds was optimized and led to a radiochemical yield of 25-60%, depending on the alkylhalide used. The preparation of n.c.a. 1-(3-bromopropoxy)-4-[{sup 18}F]fluorobenzene proved advantageous in comparison to direct use of 4-[{sup 18}]fluorophenol for coupling with a corresponding N-protected precursor for the synthesis of n.c.a. [{sup 18}F]FPTEA. With regard to the radiochemical yields and the loss of activity during the synthesis and isolation of n.c.a. 4-[{sup 18}F]fluorophenol and n.c.a. 1-(3-bromopropoxy)-4-[{sup 18}F]fluorobenzene, [{sup 18}F]FPTEA was obtained by reaction with 2-(4-tolyloxy

  5. Properties of cast Ti-stabilised stainless steel after long-term ageing

    International Nuclear Information System (INIS)

    Ehrnsten, U.; Karjalainen-Roikonen, P.; Nenonen, P.; Ahlstrand, R.; Hietanen, O.; Timofeev, B.T.; Bloomin, A.A.

    2000-01-01

    Mechanical properties and microstructure are studied and compared for two kinds of specimens of cast Ti-stabilized stainless steel 08Kh18N10T used for manufacturing of valves and pumps in nuclear power plants. One set of specimens represents the main gate valve material after 106000 h (∼ 12 years) operation at 270 deg C. The comparison is made with reference specimens in as-fabricated state. The results of impact tests, hardness measurements and microscopic examination show that 12 year operation gives rise to the shift of ductile-brittle transition temperature to higher values (from - 68 deg C - 103 deg C). The microstructure of both materials is similar. The microhardness of δ-ferrite in the steel after long-term operation is slightly higher [ru

  6. Feasibility study on decontamination of the contaminated stainless steel with HBF4 solution

    International Nuclear Information System (INIS)

    Dong Ruilin; Zhang Yuan; Qiu Dangui; Huang Yuying; Ren Xianwen

    2002-01-01

    Decontamination experiments were carried out with HBF 4 solution on the following four kinds of sample: 1Cr18Ni9Ti stainless steel with and without welding line, 1Cr18Ni9Ti stainless steel with oxide layer formed in boiling concentrated nitric acid solution, natural uranium and 230 Th contaminated stainless steel pipe sample from one decommissioning nuclear facility. The results indicated that the oxide layer, the welding line of the 1Cr18Ni9Ti stainless steel and itself can be dissolved in the HBF 4 decontamination solution. The solubility of the 1Cr18Ni9Ti stainless steel in the HBF 4 solution used in the test is more than 5 g/L, which means that the 0.13 m 2 stainless steel could be dissolved up to a thickness of 5 μm in one liter of decontamination solution. The decontamination efficiency is more than 85% in 30 minutes for the 230 Th contaminated sample, and 87% in 2 hours for the natural uranium contaminated sample. Both samples could be decontaminated to the background level after several runs of the decontamination

  7. Precipitation and impact toughness of Nb–V stabilised 18Cr–2Mo ferritic stainless steel during isothermal aging

    International Nuclear Information System (INIS)

    Han, Jian; Li, Huijun; Barbaro, Frank; Jiang, Laizhu; Zhu, Zhixiong; Xu, Haigang; Ma, Li

    2014-01-01

    The effect of isothermal aging on precipitation behaviour and Charpy impact toughness of Nb–V stabilised 18Cr–2Mo ferritic stainless steel was investigated by means of Thermo-Calc prediction, scanning electron microscopy, transmission electron microscopy, X-ray diffraction and Charpy impact toughness testing. The results show that, niobium, vanadium carbides and nitrides, Fe 2 Nb (Laves phase) and Cr 23 C 6 formed after 2 h aging at 800 °C, and the equilibrium solvus temperature of Fe 2 Nb phase increases to above 750 °C, higher than the calculated temperature (730 °C) using Thermo-Calc. After isothermal aging at 750–950 °C, 2 h aging resulted in a decrease in toughness due to the formation of precipitation, especially (Nb,V)(C,N) and Fe 2 Nb. When isothermally aged at 800 °C for up to 24 h, the coarsening rate of Fe 2 Nb particle is much higher than that of (Nb,V)(C,N), and the impact toughness of the steel is dependent on quantity and sizes of (Nb,V)(C,N) and Fe 2 Nb particles

  8. Precipitation and impact toughness of Nb–V stabilised 18Cr–2Mo ferritic stainless steel during isothermal aging

    Energy Technology Data Exchange (ETDEWEB)

    Han, Jian, E-mail: jh595@uowmail.edu.au [School of Mechanical, Materials and Mechatronic Engineering, University of Wollongong, Wollongong, NSW 2522 (Australia); Li, Huijun [School of Mechanical, Materials and Mechatronic Engineering, University of Wollongong, Wollongong, NSW 2522 (Australia); Barbaro, Frank [School of Mechanical, Materials and Mechatronic Engineering, University of Wollongong, Wollongong, NSW 2522 (Australia); CBMM Technology Suisse, 14, Rue du Rhone, Geneve 1204 (Switzerland); Jiang, Laizhu [Baoshan Iron and Steel Co., Ltd., Shanghai 200431 (China); Zhu, Zhixiong [School of Mechanical, Materials and Mechatronic Engineering, University of Wollongong, Wollongong, NSW 2522 (Australia); Xu, Haigang; Ma, Li [Baoshan Iron and Steel Co., Ltd., Shanghai 200431 (China)

    2014-08-26

    The effect of isothermal aging on precipitation behaviour and Charpy impact toughness of Nb–V stabilised 18Cr–2Mo ferritic stainless steel was investigated by means of Thermo-Calc prediction, scanning electron microscopy, transmission electron microscopy, X-ray diffraction and Charpy impact toughness testing. The results show that, niobium, vanadium carbides and nitrides, Fe{sub 2}Nb (Laves phase) and Cr{sub 23}C{sub 6} formed after 2 h aging at 800 °C, and the equilibrium solvus temperature of Fe{sub 2}Nb phase increases to above 750 °C, higher than the calculated temperature (730 °C) using Thermo-Calc. After isothermal aging at 750–950 °C, 2 h aging resulted in a decrease in toughness due to the formation of precipitation, especially (Nb,V)(C,N) and Fe{sub 2}Nb. When isothermally aged at 800 °C for up to 24 h, the coarsening rate of Fe{sub 2}Nb particle is much higher than that of (Nb,V)(C,N), and the impact toughness of the steel is dependent on quantity and sizes of (Nb,V)(C,N) and Fe{sub 2}Nb particles.

  9. Investigation programme and procedure for creep and long-term rupture strength in materials with accounting for stress deviator and loading history

    International Nuclear Information System (INIS)

    Mozharovskaya, T.N.

    1984-01-01

    A programme and procedure are given to study 08Kh18N9 steel at 600 deg C and 15Kh2MFA steel at 550 deg C for creep and long-term strength at different parameters of proportional loading as well as at different parameters under loading in two-link irregular trajectories. This makes it possible to estimate the effect of the kind of a stress deviator, history and prehistory of loading on plastic deformation in creep and on failure under long-term loading

  10. Investigation programme and procedure for creep and long-term rupture strength in materials with accounting for stress deviator and loading history

    Energy Technology Data Exchange (ETDEWEB)

    Mozharovskaya, T N [AN Ukrainskoj SSR, Kiev. Inst. Problem Prochnosti

    1984-11-01

    A programme and procedure are given to study 08Kh18N9 steel at 600 deg C and 15Kh2MFA steel at 550 deg C for creep and long-term strength at different parameters of proportional loading as well as at different parameters under loading in two-link irregular trajectories. This makes it possible to estimate the effect of the kind of a stress deviator, history and prehistory of loading on plastic deformation in creep and on failure under long-term loading.

  11. Metastable structure formation during high velocity grinding

    International Nuclear Information System (INIS)

    Samarin, A.N.; Klyuev, M.M.

    1984-01-01

    Metastable structures in surface layers of samples are; investigated during force high-velocity abrasive grinding. Samples of martensitic (40Kh13), austenitic (12Kh18N10T), ferritic (05Kh23Yu5) steels and some alloys, in particular KhN77TYuR (EhI437B), were grinded for one pass at treatment depth from 0.17 up to 2.6 mm. It is established that processes of homogenizing, recrystallization and coagulation are; developed during force high-velocity grinding along with polymorphic transformations in the zone of thermomechanical effect, that leads to changes of physical and mechanical properties of the surface

  12. Electrochemical impedance spectrometry using Inconel 690, zircaloy 4, 316Ti steel, 17-4-PH, UR52N et URSB8. Simulation in tritiated water. Tome 2

    International Nuclear Information System (INIS)

    Bellanger, G.

    1994-11-01

    The redox potential of 3 H 2 O, as well as the corrosion potentials in this medium are found, abnormally, in the trans-passive region. This is completely different from behavior in the chemical industry or in the water in nuclear powers. With such behavior, there will be breakdowns of the protective oxide layers, and in the presence of chloride there will be immediate pitting. Polarization and electrochemical impedance spectrometry curves are presented and discussed. These curves make it possible to ascertain the corrosion domains and to compare the kinetics of different stainless steel alloys. These corrosion kinetics and the corrosion potentials provide a classification of the steels studied here: Inconel 690, zircaloy 4, 316 Ti steel, 17-4-PH, UR52N et URSB8. From the results it can be concluded that URSB8 has the best corrosion resistance. (author). 13 refs., 522 figs., tabs

  13. Microstructure and Mechanical Properties of Fe-18Mn-18Cr-0.5N Austenitic Nonmagnetic Stainless Steel in Asymmetric Hot Rolling

    Science.gov (United States)

    Song, Y. L.; Li, C. S.; Ma, B.; Han, Y. H.

    2017-05-01

    Asymmetric hot rolling (ASHR) with a mismatch speed ratio of 1.15 in a single pass was applied to Fe-18Mn-18Cr-0.5N steel and was compared with symmetric hot rolling (SHR). The results indicated that a through-thickness microstructure gradient was formed in the plate due to the shear strain (0.36) introduced by ASHR. A fine-grained layer with the average size of 3 μm was achieved at the top surface of ASHR plate, while numerous elongated grains with a few recrystallized grains were presented at the center layer. The texture was distributed randomly at the top surface of ASHR plate, and a weaker intensity of typical hot-rolled texture in austenitic steel was obtained at the center layer of ASHR plate compared to SHR plate. An excellent combination of microhardness, strength and ductility was obtained in the ASHR plate, which was attributed to gradient microstructure induced by ASHR.

  14. Alloy spreading and filling of gaps in brazing of VDU-2 and KhN50VMTYuB heat resistant nickel alloys with VPr3K and VPr10 alloys

    International Nuclear Information System (INIS)

    Shapiro, A.E.; Podol'skij, B.A.; Lepisko, M.R.; Borzyak, A.G.; Moryakov, V.F.; Rostislavskaya, T.T.

    1984-01-01

    A study was made on contact interaction of VDU-2 and KhN50VMTYuB alloys with VPr3K and VPr10 alloys at 1325 and 1220 deg C in argon and industrial vacuum. The contact angles and wettability indexes were determined. The solders fill the vertical gaps of up to 0.25 mm width through 80 mm height. Spreading and filling of gaps proceeds better during soldering in argon with boron trifluoride addition as compared to soldering in industrial vacuum. VPr10 alloy is divided into two phases when wetting KhN50VMTYuB alloy: fusible one on the base of nickel-chromium-manganese solution and infusible one on the base of nickel-niobium eutectics. The square of fusible phase spreading is 2.5...3 times larger as compared to infusible one

  15. Corrosion resistance of metals and alloys in molten alkalies

    International Nuclear Information System (INIS)

    Zarubitskij, O.G.; Dmitruk, B.F.; Minets, L.A.

    1979-01-01

    Literature data on the corrosion of non-ferrous and noble metals, iron and steels in the molten alkalis and mixtures of their base are presented. It is shown that zirconium, niobium and tantalum are characterized by high corrosion stability in the molten NaOH. Additions of NaOH and KOH to the alkali chloride melts result in a 1000 time decrease of zirconium corrosion rate at 850 deg. The data testify to the characteristic passivating properties of OH - ions; Mo and W do not possess an ability to selfpassivation in hydroxide melts. Corrosion resistance of carbon and chromium-nickel steels in hydroxide melts depends considerably on the temperature, electrolyte composition and atmosphere over them. At the temperatures up to 600 deg C chromium-nickel steel is corrosion resistant in the molten alkali only in the inert atmosphere. Corrosion rate of chromium-nickel alloy is the lower the less chromium and the more nickel it contains. For the small installations the 4Kh18N25S2 and Kh23N28M3D3T steels can be recommended

  16. Hot Deformation Behavior of SA508Gr.4N Steel for Reactor Pressure Vessels

    Directory of Open Access Journals (Sweden)

    YANG Zhi-qiang

    2017-08-01

    Full Text Available The high-temperature plastic deformation and dynamic recrystallization behavior of SA508Gr.4N steel were investigated through hot deformation tests in a Gleeble1500D thermal mechanical simulator. The compression tests were performed in the temperature range of 1050-1250℃ and the strain rate range of 0.001-0.1s-1 with true strain of 0.16. The results show that from the high-temperature true stress-strain curves of the SA508Gr.4N steel, the main feature is dynamic recrystallization,and the peak stress increases with the decrease of deformation temperature or the increase of strain rate, indicating the experimental steel is temperature and strain rate sensitive material. The constitutive equation for SA508Gr.4N steel is established on the basis of the true stress-strain curves, and exhibits the characteristics of the high-temperature flow behavior quite well, while the activation energy of the steel is determined to be 383.862kJ/mol. Furthermore, an inflection point is found in the θ-σ curve, while the -dθ/dσ-σ curve shows a minimum value. The critical strain increases with increasing strain rate and decreasing deformation temperature. A linear relationship between critical strain (εc and peak strain (εp is found and could be expressed as εc/εp=0.517. The predicted model of critical strain could be described as εc=8.57×10-4Z0.148.

  17. Synthesis of a dopamine transporter imaging agent, N-(3-[18F]fluoropropyl)-2β-carbomethoxy-3β-(4-iodophenyl)nortropane

    International Nuclear Information System (INIS)

    Choi, Yearn Seong; Oh, Seung Jun; Kim, Sang Eun; Choi, Yong; Lee, Kyung Han; Kim, Byung Tae; Chi, Dae Yoon

    1999-01-01

    N-(3-[ 18 F]fluoropropyl)-2β-carbomethoxy-3β-(4-iodophenyl)nortropane ([ 18 F]FP-CIT) has been shown to be very useful for imaging the dopamine transporter. However, synthesis of this radiotracer is somewhat troublesome. In this study, we used a new method for the preparation of ([ 18 F]FP-CIT) to increse radiochemical yield and effective specific activity. ([ 18 F]FP-CIT) was prepared by N-alkylation of nor β-CIT (2 mg) with 3-bromo-1 ([ 18 F]fluoropropane in the presence of Et 3 N (5-6 drops of DMF/CH 3 CN, 140 .deg. C, 20 min). 3-Bromo-1-[ 18 F]fluropropane was synthesized from 5 μL of 3-bromo-1-trifluoromethanesulfonyloxypropane (3-bromopropyl-1-triflate) and nBu 4 N 18 F at 80 .deg. C.The final compound was purified by reverse phase HPLC and formulated in 13% ethanol in saline. 3-Bromo-1-[ 18 F]fluoropropane was obtained from 3-bromopropyl-1-triflate and nBu 4 N 18 F in 77-80% yield. N-Alkylation of nor β-CIT with 3-bromo-1-[ 18 F]fluoropropane was carried out at 140 .deg. C using acetonitrile containing a small volume of DMF as the solvents. The overall yield of [ 18 F]FP-CIT was 5-10% (decay-corrected ) with a radiochemical purity higher than 99% and effective specific activity higher than the one reported in the literature based on their HPLC data. The final [ 18 F]FP-CIT solution had the optimal pH (7.0) and it was pyrogen-free. In this study, 3-bromopropyl-1-triflate was used as the precursor for the [ 18 F]fluorination reaction and new conditions were developed for purification of [ 18 F]FP-CIT by HPLC. We established this new method for the preparation of [ 18 F]FP-CIT, which gave high effective specific activity and relatively good yield.

  18. Increasing the brittle fracture resistance in manual arc welding and heat treatment of type 12KhM steels

    International Nuclear Information System (INIS)

    Tikhonov, V.P.; Bychenkova, G.A.; Gordeev, Y.V.; Ilyuhov, C.V.

    1984-01-01

    The extensive application of heat-resisting steels is delayed by their poor weldability. Optimum technology has been developed for manual arc welding and heat treatment of structures of type 12KhM steels resulting in high cracking resistance. Trials were conducted to evaluate the efficiency of removing the structural stresses in tempering the structures. On the basis of the experimental results, it may be assumed that the toughness properties of the welded joints produced by manual arc welding can be improved by optimizing the alloying system of the weld metal, with the parent metal treated in the optimum heat treatment conditions. The aim of subsequent investigations was to assess the properties of the weld metal made with vanadium-free electrodes. It was found that the impact toughness increased two to three times; the mean hardness and the maximum hardness were both less than 220. The reduction in hardness and increase of the toughness properties of the metal are caused by the lower degree of hardening of the bulk of the grain and, consequently, by the lower concentration of plastic strain at the grain boundaries

  19. Rupture of the steel-12KH1MF under creep at temperatures close to 0,5 Tsub(melt)

    International Nuclear Information System (INIS)

    Berezina, T.G.; Ashikhmina, L.A.; Karasev, V.V.

    1976-01-01

    Optical and transmission microscopy and fractography techniques have been employed in studying the peculiarities of nucleation and growth of micropores in steel 12Kh1MF at creep. The nucleation of micropores occurs at the initial stages of creep at stress concentration points, predominantly following the retarded shear mechanism. Micropores grow by the way of diffusion, as well as following the deslocation mechanism. An important role in the process of micropore growth is played by pore opening through grain-boundary slip. Pores of 1 to 5 microns in size can be formed along grain boundaries both due to the growth of individual micropores and by coalescence of micropores at points of their concentration. Transition of the creep to the critical phase coincides with the process of the pores blending together to

  20. Heat treatment effect on the properties of the EhP767 maraging steel welded joints

    International Nuclear Information System (INIS)

    Taver, E.I.; Piskarev, M.N.; Yushchenko, K.A.; Pustovit, A.I.; Anisimova, M.S.

    1977-01-01

    Heat treatment effect on properties of welded joints of maraging 03Kh13N4K13M3T (EhP767) steel with yield strength over 150 kgs/mm 2 has been investigated. It is shown, that change in impact strength of aged joints at - 196 deg C depends on the amount of residual austenite and grain size. To stabilize 20-40 % residual austenite heat treatment regimes have been developed. Recommended are quenching at 1030-1050 deg C, sub-zero treatment and aging at 520 deg C for 16 hrs

  1. Two new three-dimensional zinc phosphites templated by piperazine: [H2pip][Zn3(HPO3)4(H2O)2] and K[H2pip]0.5[Zn3(HPO3)4

    Science.gov (United States)

    Zhang, Xiao; Wang, Guo-Ming; Wang, Zong-Hua; Wang, Ying-Xia; Lin, Jian-Hua

    2014-01-01

    Two three-dimensional open-framework zinc phosphites with the same organically templated, [H2pip][Zn3(HPO3)4(H2O)2] (1) and K[H2pip]0.5[Zn3(HPO3)4] (2) (pip = piperazine), have been solvothermally synthesized and structurally characterized by IR, elemental analysis, thermogravimetric analysis, powder and single-crystal X-ray diffractions. Compound 1 consists of ZnO4 tetrahedra, [HPO3] pseudopyramids and [ZnO4(H2O)2] octahedra, which are linked through their vertexes to generate three-dimensional architecture with intersecting 8-membered channels along the [1 0 0], [0 0 1] and [1 0 1] directions. Compound 2 is constructed from strictly alternating ZnO4 tetrahedra and [HPO3] pseudopyramids, and exhibits (3,4)-connected inorganic framework with 8-, and 12-membered channels, in which the K+ and diprotonated H2pip2+ extra-framework cations reside, respectively. The coexistence of inorganic K+ and organic piperazine mixed templates in the structure is unique and, to the best of our knowledge, firstly observed in metal-phosphite materials. In addition, the participation of left-handed and right-handed helical chains in construction of the puckered 4.82 sheet structure in 2 is also noteworthy.

  2. Boron effect on fabrication properties and service behaviour of complex corrosion-resistant steels

    International Nuclear Information System (INIS)

    Gol'dshtejn, Ya.E.; Piskunova, A.I.; Shmatko, M.N.

    1978-01-01

    In order to determine the optimum boron admixtures for the improvement of the technological plasticity without the considerable reduction in the corrosion resistance of the complex alloy Cr-Ni-Mo steels, industrial heats of the 03KH16N15M3, 03KH17N14M3 and other steels, containing 0.0005-0.003% boron, have been researched. The plasticity, corrosion resistance and microstructure of certain steels have been determined. It is shown that small additions of boron enhance the technological plasticity during the ingot rolling. In order to prevent a sharp reduction in the corrosion resistance, the boron content should be confined to 0.0015% and the quenching temperature raised to 1,120-1,150 deg C. The positive effect of the quenching temperature increase is accounted for by the solution of the excess phases and by the reduction of the dislocation density in the near-the-boundary zones

  3. On the inhibition of mild steel corrosion by 4-amino-5-phenyl-4H-1, 2, 4-trizole-3-thiol

    International Nuclear Information System (INIS)

    Musa, Ahmed Y.; Kadhum, Abdul Amir H.; Mohamad, Abu Bakar; Takriff, Mohd Sobri; Daud, Abdul Razak; Kamarudin, Siti Kartom

    2010-01-01

    The corrosion inhibition of mild steel in a 2.5 M H 2 SO 4 solution by 4-amino-5-phenyl-4H-1, 2, 4-trizole-3-thiol (APTT) was studied at different temperatures, utilising open circuit potential, potentiodynamic and impedance measurements. The results indicate that APTT performed as an excellent mixed-type inhibitor for mild steel corrosion in a 2.5 M H 2 SO 4 solution and that the inhibition efficiencies increased with the inhibitor concentration but decreased proportionally with temperature. The kinetic and thermodynamic parameters for adsorption of APTT on the mild steel surface were calculated. A chemisorption mechanism of APTT molecules on the mild steel surface was proposed based on the thermodynamic adsorption parameters.

  4. The enhancement in wear resistance of W18Cr4V steel by ion implantation

    International Nuclear Information System (INIS)

    Zhou Ping; Xu Peiguang

    1987-01-01

    Two new methods of ion implantation were adopted in comparison with nitrogen implantation: carbon monoxide was implanted directly into W18Cr4V steel, and nitrogen was implanted into a deposited titanium film about 1000 A thick. It is shown that higher surface hardness and wear resistance have been achieved. The composition and phase structure of the implanted layer was determined in detail. The wear mechanisms were discussed

  5. An automated GC-C-GC-IRMS setup to measure palaeoatmospheric δ13C-CH4, δ15N-N2O and δ18O-N2O in one ice core sample

    Directory of Open Access Journals (Sweden)

    P. Sperlich

    2013-08-01

    Full Text Available Air bubbles in ice core samples represent the only opportunity to study the mixing ratio and isotopic variability of palaeoatmospheric CH4 and N2O. The highest possible precision in isotope measurements is required to maximize the resolving power for CH4 and N2O sink and source reconstructions. We present a new setup to measure δ13C-CH4, δ15N-N2O and δ18O-N2O isotope ratios in one ice core sample and with one single IRMS instrument, with a precision of 0.09, 0.6 and 0.7‰, respectively, as determined on 0.6–1.6 nmol CH4 and 0.25–0.6 nmol N2O. The isotope ratios are referenced to the VPDB scale (δ13C-CH4, the N2-air scale (δ15N-N2O and the VSMOW scale (δ18O-N2O. Ice core samples of 200–500 g are melted while the air is constantly extracted to minimize gas dissolution. A helium carrier gas flow transports the sample through the analytical system. We introduce a new gold catalyst to oxidize CO to CO2 in the air sample. CH4 and N2O are then separated from N2, O2, Ar and CO2 before they get pre-concentrated and separated by gas chromatography. A combustion unit is required for δ13C-CH4 analysis, which is equipped with a constant oxygen supply as well as a post-combustion trap and a post-combustion GC column (GC-C-GC-IRMS. The post-combustion trap and the second GC column in the GC-C-GC-IRMS combination prevent Kr and N2O interferences during the isotopic analysis of CH4-derived CO2. These steps increase the time for δ13C-CH4 measurements, which is used to measure δ15N-N2O and δ18O-N2O first and then δ13C-CH4. The analytical time is adjusted to ensure stable conditions in the ion source before each sample gas enters the IRMS, thereby improving the precision achieved for measurements of CH4 and N2O on the same IRMS. The precision of our measurements is comparable to or better than that of recently published systems. Our setup is calibrated by analysing multiple reference gases that were injected over bubble-free ice samples. We show

  6. Structural evolution of Fe-18Ni-16Cr-4Al steel during aging at 950 .deg. C

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Man; Jang, Jinsung [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Zhou, Zhangjian [School of Materials Science and Engineering, USTB, Beijing (China)

    2015-05-15

    Austenitic stainless steels are also among important structural materials for in-core components of nuclear reactors, and the performance, the oxidation resistance as well as the mechanical strength at high temperature are further expected after Fukushima accident. Alumina-forming austenitic (AFA) steel was first developed by Y. Yamamoto et al. , which showed a good combination of oxidation resistance and creep resistance. The strengthening is achieved through nano-sized MX and Laves. Microstructural evolution of Fe-18Ni-16Cr-4Al during aging at 950 .deg. C was studied. This steel consists of two phases of austenite and ferrite. During aging, needle-shaped NiAl precipitates in austenite, while round shaped NiAl form in ferrite, which is supposed to be due to different crystal structural parameters.

  7. Experimental and computational studies of naphthyridine derivatives as corrosion inhibitor for N80 steel in 15% hydrochloric acid

    Science.gov (United States)

    Ansari, K. R.; Quraishi, M. A.

    2015-05-01

    The inhibition effect of three naphthyridine derivatives namely 2-amino-4-(4-methoxyphenyl)-1,8-naphthyridine-3-carbonitrile (ANC-1), 2-amino-4-(4-methylphenyl)-1,8-naphthyridine-3-carbonitrile (ANC-2) and 2-amino-4-(3-nitrophenyl)-1,8-naphthyridine-3-carbonitrile (ANC-3) as corrosion inhibitors for N80 steel in 15% HCl by using gravimetric, electrochemical techniques (EIS and potentiodynamic polarization), SEM, EDX and quantum chemical calculation. The order of inhibition efficiency is ANC-1>ANC-2>ANC-3. Potentiodynamic polarization reveals that these inhibitors are mixed type with predominant cathodic control. Studied inhibitors obey the Langmuir adsorption isotherm. The quantum calculation is in good agreement with experimental results.

  8. Long-term behaviour of heat-resistant steels and high-temperature materials

    International Nuclear Information System (INIS)

    1987-01-01

    This book contains 10 lectures with the following subjects: On the effect of thermal pretreatment on the structure and creep behaviour of the alloy 800 H (V. Guttmann, J. Timm); Material properties of heat resistant ferritic and austenitic steels after cold forming (W. Bendick, H. Weber); Investigations for judging the working behaviour of components made of alloy 800 and alloy 617 under creep stress (H.J. Penkalla, F. Schubert); Creep behaviour of gas turbine materials in hot gas (K.H. Kloos et al.); Effect of small cold forming on the creep beahviour of gas turbine blades made of Nimonic 90 (K.H. Keienburg et al.); Investigations on creep fatigue alternating load strength of nickel alloys (G. Raule); Change of structure, creep fatigue behaviour and life of X20 Cr Mo V 12 1 (by G. Eggeler et al.); Investigations on thermal fatigue behaviour (K.H. Mayer et al.); Creep behaviour of similar welds of the steels 13 Cr Mo 4 4, 14 MoV 6 3, 10 Cr Mo 910 and GS-17 Cr Mo V 5 11 (K. Niel et al.); Determining the creep crack behaviour of heat resistant steels with samples of different geometry (K. Maile, R. Tscheuschner). (orig.,/MM) [de

  9. Microstructure and mechanical properties of friction stir welded 18Cr–2Mo ferritic stainless steel thick plate

    International Nuclear Information System (INIS)

    Han, Jian; Li, Huijun; Zhu, Zhixiong; Barbaro, Frank; Jiang, Laizhu; Xu, Haigang; Ma, Li

    2014-01-01

    Highlights: • We focus on friction stir welding of 18Cr–2Mo ferritic stainless steel thick plate. • We produce high-quality joints with special tool and optimised welding parameters. • We compare microstructure and mechanical properties of steel and joint. • Friction stir welding is a method that can maintain the properties of joint. - Abstract: In this study, microstructure and mechanical properties of a friction stir welded 18Cr–2Mo ferritic stainless steel thick plate were investigated. The 5.4 mm thick plates with excellent properties were welded at a constant rotational speed and a changeable welding speed using a composite tool featuring a chosen volume fraction of cubic boron nitride (cBN) in a W–Re matrix. The high-quality welds were successfully produced with optimised welding parameters, and studied by means of optical microscopy (OM), scanning electron microscopy (SEM), electron back-scattered diffraction (EBSD) and standard hardness and impact toughness testing. The results show that microstructure and mechanical properties of the joints are affected greatly, which is mainly related to the remarkably fine-grained microstructure of equiaxed ferrite that is observed in the friction stir welded joint. Meanwhile, the ratios of low-angle grain boundary in the stir zone regions significantly increase, and the texture turns strong. Compared with the base material, mechanical properties of the joint are maintained in a comparatively high level

  10. Synergistic enhancing effect of N+C alloying on cyclic deformation behaviors in austenitic steel

    Energy Technology Data Exchange (ETDEWEB)

    Kang, J. [State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004 (China); Zhang, F.C., E-mail: zfc@ysu.edu.cn [State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004 (China); Long, X.Y. [State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004 (China); Yang, Z.N. [National Engineering Research Center for Equipment and Technology of Cold Strip Rolling, Yanshan University, Qinhuangdao 066004 (China)

    2014-07-29

    Cyclic plastic and elastic strain controlled deformation behaviors of Mn18Cr7 austenitic steel with N0.6C0.3 synergistic enhancing alloying have been investigated using tension-compression low cycle fatigue and three-point bending high cycle fatigue testing. Results of cyclic deformation characteristic and fatigue damage mechanism have been compared to that in Mn12C1.2 steel. Mn18Cr7N0.6C0.3 steel always shows cyclic softening caused by enhanced planar sliding due to the interaction between N+C and the substitutional atoms as well as the dislocation, which is totally different from cyclic hardening in Mn12C1.2 steel caused by the interaction between C members of C–Mn couples with the dislocation. Enhanced effective stress is obtained due to the solid solution strengthening effect caused by the short range order at low strain amplitude while this effect does not work at high strain amplitude. Internal stress contributes most to the cyclic softening with the increase of strain amplitudes. Significant planar slip characteristic can be observed resulting from low stacking fault energy and high short range order effects in Mn18Cr7N0.6C0.3 steel and finally the parallel or intersecting thin sheets with dislocation tangles separated by dislocation free sheets are obtained with the prolonged cycles under cyclic elastic or plastic strain controlled fatigue testing. There exist amounts of small cracks on the surface of the Mn18Cr7N0.6C0.3 steel because fatigue crack initiation is promoted by the cyclic plastic strain localization. However, the zigzag configuration of the cracks reveals that the fatigue crack propagation is highly inhibited by the planar slip characteristic, which eventually improves the fatigue life.

  11. Study of regularities in propagation of thermal fatigue cracks

    International Nuclear Information System (INIS)

    Tachkova, N.G.; Sobolev, N.D.; Egorov, V.I.; Rostovtsev, Yu.V.; Ivanov, Yu.S.; Sirotin, V.L.

    1978-01-01

    Regularities in the propagation of thermal fatigue cracks in the Cr-Ni steels of the austenite class depending upon deformation conditions in the crack zone, have been considered. Thin-walled tube samples of the Kh16N40, Kh18N20 and Kh16N15 steels have been tested in the 10O reversible 400 deg C and 100 reversible 500 deg C regimes. The samples have possessed a slot-shaped stress concentrator. Stress intensity pseudocoefficient has been calculated for the correlation of experimental data. The formula for determining crack propagation rate has been obtained. The experiments permit to conclude that propagation rate of thermal fatigue cracks in the above steels depends upon the scope of plastic deformation during a cycle and stress intensity pseudocoefficient, and is determined by plastic deformation resistance during thermal cyclic loading

  12. On abnormal decomposition of supercooled austenite in carbon and alloy steels

    International Nuclear Information System (INIS)

    Parusov, V.V.; Dolzhenkov, I.I.; Podobedov, L.V.; Vakulenko, I.A.

    1980-01-01

    Residual stresses which appear as a result of thermal cycling in the temperature range of 300-700 deg C are investigated in an austenitic class steel (03Kh18N11) to ground the assumption on the effect of plastic deformation, appearing due to thermal stresses, on the mechanism of supercooled austenite decomposition. The determination of residual stresses is carried out with the help of X-ray diffraction analysis. It is established that the deformation brings about an increase in density of dislocation the interaction of which leads to the formation of a typical austenite substructure which conditions the proceeding of the eutectoid transformation according to an abnormal mechanism. It is noted, that the grain pearlite formation due to plastic and microplastic deformation of supercooled austenite induced by thermal stresses should be taken into account when developing steel heat treatment shedules [ru

  13. Ultrathin g-C3N4 films supported on Attapulgite nanofibers with enhanced photocatalytic performance

    Science.gov (United States)

    Xu, Yongshuai; Zhang, Lili; Yin, Minghui; Xie, Dengyu; Chen, Jiaqi; Yin, Jingzhou; Fu, Yongsheng; Zhao, Pusu; Zhong, Hui; Zhao, Yijiang; Wang, Xin

    2018-05-01

    A novel visible-light-responsive photocatalyst is fabricated by introducing g-C3N4 ultrathin films onto the surface of attapulgite (ATP) via a simple in-situ depositing technique, in which ATP was pre-grafted using (3-Glycidyloxypropyl) trimethoxysilane (KH560) as the surfactant. A combination of XRD, FT-IR, BET, XPS, UV-vis, TEM and SEM techniques are utilized to characterize the composition, morphology and optical properties of the products. The results show that with the help of KH560, g-C3N4 presented as ultrathin layer is uniformly loaded onto the surface of ATP by forming a new chemical bond (Sisbnd Osbnd C). Comparing with g-C3N4 and ATP, ATP/g-C3N4 exhibits remarkably enhanced visible-light photocatalytic activity in degradation of methyl orange (MO) because of its high surface area, appropriate band gap and the synergistic effect between g-C3N4 and ATP. To achieve the best photocatalyst, the ratio of g-C3N4 was adjusted by controlling the mass portion between ATP-KH560 and melamine (r = m (ATP-KH560)/m (melamine)). The highest decomposition rate of methyl orange (MO) was 96.06% when r = 0.5 and this degradation efficiency remained unchanged after 4 cycles, which is 10 times as that of pure g-C3N4 particles. Possible photocatalytic mechanism is presented.

  14. Bromine-rich Zinc Bromides: Zn6Br12(18-crown-6)2×(Br2)5, Zn4Br8(18-crown-6)2×(Br2)3, and Zn6Br12(18-crown-6)2×(Br2)2.

    Science.gov (United States)

    Hausmann, David; Feldmann, Claus

    2016-06-20

    The bromine-rich zinc bromides Zn6Br12(18-crown-6)2×(Br2)5 (1), Zn4Br8(18-crown-6)2×(Br2)3 (2), and Zn6Br12(18-crown-6)2×(Br2)2 (3) are prepared by reaction of ZnBr2, 18-crown-6, and elemental bromine in the ionic liquid [MeBu3N][N(Tf)2] (N(Tf)2 = bis(trifluoromethylsulfonyl)amide). Zn6Br12(18-crown-6)2×(Br2)5 (1) is formed instantaneously by the reaction. Even at room temperature, compound 1 releases bromine, which was confirmed by thermogravimetry (TG) and mass spectrometry (MS). The release of Br2 can also be directly followed by the color and density of the title compounds. With controlled conditions (2 weeks, 25 °C, absence of excess Br2) Zn6Br12(18-crown-6)2×(Br2)5 (1) slowly releases bromine with conconcurrent generation of Zn4Br8(18-crown-6)2×(Br2)3 (2) (in ionic liquid) and Zn6Br12(18-crown-6)2×(Br2)2 (3) (in inert oil). All bromine-rich zinc bromides contain voluminous uncharged (e.g., Zn3Br6(18-crown-6), Zn2Br4(18-crown-6)) or ionic (e.g., [Zn2Br3(18-crown-6)](+), [(Zn2Br6)×(Br2)2](2-)) building units with dibromine molecules between the Zn oligomers and partially interconnecting the Zn-containing building units. Due to the structural similarity, the bromine release is possible via crystal-to-crystal transformation with retention of the crystal shape.

  15. N-(n-benzylpiperidin-4-yl)-2-[18f]fluorobenzamide: a potential ligand for PET imaging of breast cancer

    International Nuclear Information System (INIS)

    Shiue, Chyng-Yann; Shiue, Grace G.; Benard, Francois; Visonneau, Sophie; Santoli, Daniela; Alavi, Abass A.

    2000-01-01

    N-(N-Benzylpiperidin-4-yl)-2-[ 18 F]fluorobenzamide (2), a potential ligand for PET imaging of sigma receptor, has been found to be a potential agent for detection of breast cancer. In vivo studies in severe combined immunodeficient (SCID) mice bearing MDA-MB231 tumors showed that the uptake of compound 2 in these tumors was high (3.8%/g); the ratios of tumor/muscle and tumor/blood were 6.2 and 7.0, respectively, at 1 h postinjection. Pretreatment of SCID mice with haldol increased the uptake of compound 2 in blood, muscle, and other well-perfused organs while decreasing its uptake in tumors. The ratios of tumor/muscle and tumor/blood decreased from 6.2 and 7.0 to 1.3 and 1.1, respectively, at 1 h postinjection. At 2 h postinjection, the ratios of tumor/muscle and tumor/blood decreased from 4.9 and 7.8 to 1.4 and 1.4, respectively. The tumor uptake of compound 2 in SCID mice bearing primary tumor explants from a human breast cancer patient was lower than that in MDA-MB231 tumors (1.66%/g versus 3.78%/g), and the ratios of tumor/muscle and tumor/blood were 3.5 and 3.7, respectively, at 1 h postinjection. These results suggest that compound 2 may be a potential ligand for PET imaging of breast cancer

  16. Vibrational modes of deuterium in KD2PO4

    International Nuclear Information System (INIS)

    Mizoguchi, Kohji; Agui, Akane; Tominaga, Yasunori; Nakai, Yusuke; Ikeda, Susumu.

    1993-01-01

    In order to study the deuteration effect in hydrogen-bonded compounds such as KH 2 PO 4 , hydrogen and deuterium modes in KH 2 PO 4 and K(D x H 1-x ) 2 PO 4 (x = 95 %) were investigated by means of inelastic neutron-scattering measurements over a wide energy range. By comparing Raman spectra of KH 2 PO 4 and KD 2 PO 4 with neutron-scattering spectra, the vibrational modes of deuterium and those of PO 4 tetrahedrons in the energy range of 30 < ε < 150 meV have been investigated. At least two deuterium modes have been found at 87 meV and 106 meV. (author)

  17. Neutron irradiation effects on mechanical properties in SA508 Gr4N high strength low alloy steel

    International Nuclear Information System (INIS)

    Kim, Minchul; Lee, Kihyoung; Park, Sanggyu; Choi, Kwonjae; Lee, Bongsang

    2012-01-01

    The Reactor Pressure Vessel (RPV) is the key component in determining the lifetime of nuclear power plants because it is subject to the significant aging degradation by irradiation and thermal aging, and there is no practical method for replacing that component. Advanced reactors with much larger capacity than current reactor require the usage of higher strength materials inevitably. The SA508 Gr.4N Ni Cr Mo low alloy steel, in which Ni and Cr contents are larger than in conventional RPV steels, could be a promising RPV material offering improved strength and toughness from its tempered martensitic microstructure. For a structural integrity of RPV, the effect of neutron irradiation on the material property is one of the key issues. The RPV materials suffer from the significant degradation of transition properties by the irradiation embrittlement when its strength is increased by a hardening mechanism. Therefore, the potential for application of SA508 Gr.4N steel as the structural components for nuclear power reactors depends on its ability to maintain adequate transition properties against the operating neutron does. However, it is not easy to fine the data on the irradiation effect on the mechanical properties of SA508 Gr.4N steel. In this study, the irradiation embrittlement of SA508 Gr.4N Ni Cr Mo low alloy steel was evaluated by using specimens irradiated in research reactor. For comparison, the variations of mechanical properties by neutron irradiation for commercial SA508 Gr.3 Mn Mo Ni low alloy steel were also evaluated

  18. Role of grain refinement in hardening of structural steels at preliminary thermomechanical treatment

    International Nuclear Information System (INIS)

    Bukhvalov, A.B.; Grigor'eva, E.V.; Davydova, L.S.; Degtyarev, M.V.; Levit, V.I.; Smirnova, N.A.; Smirnov, L.V.

    1981-01-01

    The hardening mechanism during preliminary thermomechanical treatment with deformation by cold rolling or hydroextrusion is studied on structural 37KhN3M1 and 38KhN3MFA steels. Specimens have been tested on static tension, impact strength and fracture toughness. It is shown that hydroextrusion application instead of rolling does not change the hardening effect of preliminary thermomechanical treatment (PTMT). It is established that the increase of preliminary deformation degree and the use of accelerated short term hardening heating provides a bett er grain refinement and the increase of PTMT hardening effect [ru

  19. Master curve characterization of the fracture toughness behavior in SA508 Gr.4N low alloy steels

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Ki-Hyoung, E-mail: shirimp@kaist.ac.k [Department of Materials Science and Engineering, KAIST, Daejeon 305-701 (Korea, Republic of); Kim, Min-Chul; Lee, Bong-Sang [Nuclear Materials Research Division, KAERI, Daejeon 305-353 (Korea, Republic of); Wee, Dang-Moon [Department of Materials Science and Engineering, KAIST, Daejeon 305-701 (Korea, Republic of)

    2010-08-15

    The fracture toughness properties of the tempered martensitic SA508 Gr.4N Ni-Mo-Cr low alloy steel for reactor pressure vessels were investigated by using the master curve concept. These results were compared to those of the bainitic SA508 Gr.3 Mn-Mo-Ni low alloy steel, which is a commercial RPV material. The fracture toughness tests were conducted by 3-point bending with pre-cracked charpy (PCVN) specimens according to the ASTM E1921-09c standard method. The temperature dependency of the fracture toughness was steeper than those predicted by the standard master curve, while the bainitic SA508 Gr.3 steel fitted well with the standard prediction. In order to properly evaluate the fracture toughness of the Gr.4N steels, the exponential coefficient of the master curve equation was changed and the modified curve was applied to the fracture toughness test results of model alloys that have various chemical compositions. It was found that the modified curve provided a better description for the overall fracture toughness behavior and adequate T{sub 0} determination for the tempered martensitic SA508 Gr.4N steels.

  20. Tribological Behavior of Babbitt Alloy Rubbing Against Si3N4 and Steel Under Dry Friction Condition

    Science.gov (United States)

    Ji, Xianbing; Chen, Yinxia

    2016-03-01

    The tribological behavior of Babbitt alloy rubbing with Si3N4 ball and steel ball with various sliding speeds at dry friction condition was investigated. It was found that B88 alloy rubbing with Si3N4 ball and steel ball possesses a low sliding wear resistance at dry friction. The wear rate is above 10-4 mm3/Nm, and the friction coefficient is from 0.2 to 0.4. At low sliding speed of 0.05-0.1 m/s, the mainly wear mechanisms are microgroove and fatigue wear, while at high sliding speed of 0.5 m/s, the wear mechanisms depend on plastic deformation and delamination. The high wear rate indicates that it is needed to prevent Babbitt alloy from working at dry friction conditions, while the low friction coefficient suggests that it is not easy to the occurrence of cold weld.

  1. Relationships of quenching stresses to structural transformations in steel

    International Nuclear Information System (INIS)

    Loshkarev, V.E.

    1985-01-01

    Technique for accountancy of the effect of stresses on structural transformations in steel when solving problems of thermoplasticity is suggested. It is revealed on the basis of the conducted calculations that accountancy of interrelation of stressed and structural states of 20Kh2MF steel essentially affects forecasting of results of quenching

  2. The effect of laser treatment on the wear resistance of steel in corrosive media

    International Nuclear Information System (INIS)

    Plyatsko, G.V.; Porter, A.I.; Prejs, G.A.; Mojsa, M.I.

    1975-01-01

    The corrosion mechanical wearing properties of steel 45 treated with a laser beam (H 100 =7800 Mn/sq.m) under friction with nitrated steel 40KhNMA (HV=7000 Mn/sq.m), chrome cast iron Kh15M (hardened and low-temperature tempered, modified), perlite cast iron and bronze are studied. The aqueous buffers with pH=6 and 11 are used as a corrosion active media. In a weakly acid medium the most intensive wearing of steel 40KhNMA is observed at P=8 Mn/sq.m. Its wearing reduces due to increase of pressure to 12 Mn/sq.m. Extent of steel 45 wearing increases with pressure increase from 8 to 12 Mn/sg.m. Friction coefficient of this pair changes by jumps at an increase of normal pressure and its variation range is smaller than that observed in an alkaline medium. The maximum value of friction coefficient is shifted to the higher pressure. The wearing of cast iron Kh15M-steel 45 pair has an alternative pattern. In an alkaline medium the cast iron wearing intensity shows a linear increase with the normal contact pressure but that of the steel changes jumpwise attaining extreme at 8 and 12 Mn/sq.m. In a weak acid medium the intensity of grasping and graphitization at the friction surface of cast iron Kh15M-steel 45 pair is higher than that in the alkaline medium. Experiments demonstrate an effectiveness of the laser beam treatment of steel 45 for its friction in the alkaline medium with nitrated steel 40KhNMA and with hardened low-temperature tempered cast iron 45 under friction contact pressure as high as 8 Mn/sq.m, and in acid medium at 12 and 8 Mn/sq.m respectively. The laser treatment provides high corrosion-mechanical stability of steel 45 and the counterbodies described, as well as the low friction coefficient of these pairs

  3. The effect of alloying and treatment on martensite transformation during deformation in Fe-Cr-Mn steels with unstable austenite

    International Nuclear Information System (INIS)

    Malinov, L.S.; Konop, V.I.; Sokolov, K.N.

    1977-01-01

    The effect is studied of alloying with chromium (6-10%), silicon (1-2%), molybdenum (1-3%), and copper (2%), the heat treatment conditions, and the deformation conditions, or the martensitic transformation and mechanical properties of Fe-Cr-Mn steels of the transitional class based on 0G8AM2S. It is shown that appropriate alloying and treatment, taking into account the degree of stability of the austenite, can ensure a complex of high mechanical properties of the steels investigated. For instance, the treatment of steel 0Kh10AG8MD2S by the technique: hardening+ 40% deformation at 400 deg C + 10% deformation at room temperature has yielded the following mechanical properties: sigmasub(B)=150 kgf/mm 2 , sigmasub(T)=110 kgf/mm 2 , sigma=18%, psi=32%

  4. Measurement of the 19F(n,2n)18F cross section from 18 to 27 MeV

    International Nuclear Information System (INIS)

    Hartmann, C.L.; DeLuca, P.M. Jr.

    1990-01-01

    the 19 F(n,2n) 18 F cross section was measured at neutron energies of 18, 21, 23, and 27 MeV. Nearly monoenergetic neutrons bombarded teflon (CF 2 ), Zr, and Au samples. 19 F(n,2n) 18 F cross section values were determined relative to nat Zr(n,xn) 89 Zr and 197 Au(n,2n) 196 Au from measurements of the 18 F, 89 Zr, and 196 Au activities. Our results are in agreement with previous measurements below 20 MeV and extend the usefulness of this reaction to 27 MeV. 22 refs., 1 fig., 2 tabs

  5. Synthesis of 6-acrylamido-4-(2-[18F]fluoroanilino)quinazoline: Aprospective irreversible EGFR binding probe

    Energy Technology Data Exchange (ETDEWEB)

    Vasdev, Neil; Dorff, Peter N.; Gibbs, Andrew R.; Nandanan,Erathodiyil; Reid, Leanne M.; O' Neil, James P.; VanBrocklin, Henry F.

    2004-03-30

    Acrylamido-quinazolines substituted at the 6-position bindirreversibly to the intracellular ATP binding domain of the epidermalgrowth factor receptor (EGFR). A general route was developed forpreparing 6-substituted-4-anilinoquinazolines from [18F]fluoroanilinesfor evaluation as EGFR targeting agents with PET. By a cyclizationreaction, 2-[18F]fluoroaniline was reacted withN'-(2-cyano-4-nitrophenyl)-N,N-dimethylimidoformamide to produce6-nitro-4-(2-[18F]fluoroanilino)quinazoline in 27.5 percentdecay-corrected radiochemical yield. Acid mediated tin chloride reductionof the nitro group was achieved in 5 min (80 percent conversion) andsubsequent acylation with acrylic acid gave6-acrylamido-4-(2-[18F]fluoroanilino)quinazoline in 8.5 percentdecay-corrected radiochemical yield, from starting fluoride, in less than2 hours.

  6. Influence of Nb content on grain size and mechanical properties of 18 wt% Cr ferritic stainless steel

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Y. [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Mao, W.M., E-mail: weiminmao@263.net [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Chen, Y.J. [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Jing, J.; Cheng, M. [Taizhou Xinyu Precision Manufacture Company Limited, Jiangyan 225500, Jiangsu (China)

    2016-11-20

    The influence of Nb contents between 0.20 and 1.20 wt% on the grain size and mechanical properties of 18 wt% Cr ferritic stainless steel produced by investment casting was investigated. The average grain sizes of the three steels decreased apparently with increasing Nb content mainly due to the increasing number of pre-existing oxides formed at higher temperature, which were more likely to be the nuclei of heterogeneous nucleation. The thermodynamic analysis of Nb(C,N) formation was in conformity to the experimental result that the Nb(C,N) precipitates became larger with increasing Nb content. The as-cast specimen with the smallest grain size of steel C had the worse tensile strength and elongation in comparison with the as-cast specimens of steels A and B, mostly owing to the catenarian and dendritic Nb(C,N) particles distributed densely at the grain boundaries. The mechanical properties of specimens were not improved remarkably through high temperature solid-solution, whereas the mechanical properties of normalized specimens in the three steels were improved to different degrees. The coalescence and sparse distribution of smaller precipitates at grain boundaries after normalizing effectively weakened the local stress concentration arising from the reticular distribution of particles. The normalized specimen of steel A with 0.24 wt% Nb still showed good mechanical properties. Normalizing at 850 °C for 2 h is the appropriate heat treatment for the 18 wt% Cr ferritic stainless steel. The comparatively rational Nb content of the ferritic stainless steel is between 0.20 and 0.40 wt% for investment casting production.

  7. Crystallographic isomorphism in the structural type of α-HgI{sub 2} by example of KHgI{sub 3} · H{sub 2}O, β-Ag{sub 2}HgI{sub 4}, and β-Cu{sub 2}HgI{sub 4}

    Energy Technology Data Exchange (ETDEWEB)

    Borisov, S. V., E-mail: borisov@niic.nsc.ru; Magarill, S. A.; Pervukhina, N. V. [Russian Academy of Sciences, Nikolaev Institute of Inorganic Chemistry, Siberian Branch (Russian Federation)

    2017-03-15

    The structure of KHgI{sub 3} · H{sub 2}O is assigned to the family of crystal structures having the three-layer cubic packing of iodine anions with cations in the tetrahedral voids (the structures of α-HgI{sub 2}, β-Ag{sub 2}HgI{sub 4}, and β-Cu{sub 2}HgI{sub 4} among them). Crystallographic analysis shows that the nodes of the three-layer close packing are populated by iodine anions and K cations in the ratio 3/4: 1/4. Transformation of the structure of α-HgI{sub 2} into the structure of KHgI{sub 3} · H{sub 2}O can be formally represented as the replacement of (HgI){sub n}{sup +} fragments by (KH{sub 2}O){sub n}{sup +} fragments: (Hg{sub 2}I{sub 4})–(HgI){sup +} + (KH{sub 2}O){sub n}{sup +} = KHgI{sub 3} · H{sub 2}O. Perforated layers of vertex-sharing HgI{sub 4} tetrahedra break down into parallel isolated chains. Channels formed in place of I–Hg–I–Hg–fragments are occupied by–H{sub 2}O–K–-H{sub 2}-O-K-H{sub 2}O-chains weakly bound to neighbors.

  8. Evolution of the structure and the phase composition of a bainitic structural steel during plastic deformation

    Science.gov (United States)

    Nikitina, E. N.; Glezer, A. M.; Ivanov, Yu. F.; Aksenova, K. V.; Gromov, V. E.; Kazimirov, S. A.

    2017-10-01

    The evolution of the phase composition and the imperfect substructure of the 30Kh2N2MFA bainitic structural steel subjected to compressive deformation by 36% is quantitatively analyzed. It is shown that deformation is accompanied by an increase in the scalar dislocation density, a decrease in the longitudinal fragment sizes, an increase in the number of stress concentrators, the dissolution of cementite particles, and the transformation of retained austenite.

  9. Bubble formation upon crystallization of high nitrogen iron base alloys

    International Nuclear Information System (INIS)

    Svyazhin, A.G.; Sivka, E.; Skuza, Z.

    2000-01-01

    A study is made into the conditions of nitrogen bubble formation during crystallization of unalloyed iron, alloys of Fe-O, Fe-O-S systems, steels 1Kh13, 0Kh18N9 and a two-phase Fe-11%Cr-1%Mo-0.2%V steel. It is revealed that the amount of bubbles in a high nitrogen steel casting increases with a degree of nitrogen supersaturation and decreases with a cooling rate growth and with a rise of surfactant concentration in the metal. In sound castings a nitrogen content can be increased due to a cooling rate growth, nitrogen dilution with inert gas, an increase of nitrogen pressure during crystallization as well as due to the introduction of such surfactants as sulphur, selenium, tellurium, tin [ru

  10. Crystal structures of the dioxane hemisolvates of N-(7-bromomethyl-1,8-naphthyridin-2-ylacetamide and bis[N-(7-dibromomethyl-1,8-naphthyridin-2-ylacetamide

    Directory of Open Access Journals (Sweden)

    Robert Rosin

    2017-10-01

    Full Text Available The syntheses and crystal structures of N-(7-bromomethyl-1,8-naphthyridin-2-ylacetamide dioxane hemisolvate, C11H10BrN3O·0.5C4H8O2, (I, and bis[N-(7-dibromomethyl-1,8-naphthyridin-2-ylacetamide] dioxane hemisolvate, 2C11H9Br2N3O·0.5C4H8O2, (II, are described. The molecules adopt a conformation with the N—H hydrogen pointing towards the lone electron pair of the adjacent naphthyridine N atom. The crystals of (I are stabilized by a three-dimensional supramolecular network comprising N—H...N, C—H...N and C—H...O hydrogen bonds, as well as C—Br...π halogen bonds. The crystals of compound (II are stabilized by a three-dimensional supramolecular network comprising N—H...N, C—H...N and C—H...O hydrogen bonds, as well as C—H...π contacts and C—Br...π halogen bonds. The structure of the substituent attached in the 7-position of the naphthyridine skeleton has a fundamental influence on the pattern of intermolecular noncovalent bonding. While the Br atom of (I participates in weak C—Br...Oguest and C—Br...π contacts, the Br atoms of compound (II are involved in host–host interactions via C—Br...O=C, C—Br...N and C—Br...π bonding.

  11. Crustal Structure of Khövsgöl, Mongolia

    Science.gov (United States)

    Scott, A. M.; Meltzer, A.; Stachnik, J.; Russo, R.; Munkhuu, U.; Tsagaan, B.

    2017-12-01

    Mongolia is part of the Central Asian Orogenic Belt, an accretionary event that spanned 800 million years from the mid-Proterozoic to mid-Phanerozoic. As a result of the past collisional and rifting events, the modern Khövsgöl rift system of northern Mongolia contains a heterogeneous lithospheric structure. The current rift system has three parallel N-S trending basins that roughly align with terrane boundaries. Structures inherited during the accretionary events may be a factor influencing regional deformation. The forces that drive local deformation are not well understood, but varying processes have been proposed: far-field effects of India-Eurasian plate convergence, westward subduction of the Pacific plate, magmatic underplating at the base of the crust, mantle plume activity, and asthenospheric mantle convection. Determining the nature of crustal features within this poorly understood region may illuminate processes that control rifting within intracontinental settings. A network of 26 broadband seismic stations encompassing 200 square kilometers of the Khövsgöl rift system were deployed from August 2014 to June 2016. More than 2100 events were detected, and most earthquakes were concentrated near rift structures. Events between Busiin-Gol and Darkhad, the westernmost and central basins of the Khövsgöl rift system, are distributed within the crust. An active fault is outlined along the eastern border of the Darkhad basin. Khövsgöl earthquakes bound both sides of the rift. Along the northern border of Lake Khövsgöl, seismic events define a shallow active fault orthogonal to the basin. The largest event recorded within the network was a magnitude ml=5.2 located near the northeastern border of Lake Khövsgöl on 12-05-2014. The focal mechanism of this earthquake is predominantly strike-slip, but also includes an extensional component. This work focuses on earthquake relocation and calculating moment tensors and focal mechanisms of larger regional

  12. Structural changes IN THE Kh20N45M4B nickel alloys and THE Kh16N15M3B steel due to helium ion bombardment

    International Nuclear Information System (INIS)

    Kalin, B.A.; Chernikov, U.N.; Chernov, I.I.; Kozhevnikov, O.A.; Shishkin, G.N.; Yakushin, V.L.

    1986-01-01

    Using transmission electron microscopy, x-ray structural analysis, and the thermal desorption techniques, the authors carried out a detailed study of the structural and phase changes, defect formation, and helium accumulation in the He + -bombarded 16-15 austenitic steels and 20-45 nickel alloys. Microstructure of the bombarded specimens was studied using the methods of transmission electron microscopy of thin foils in the EVM-100, and EM-301G electron microscopes. Results of x-ray studies on the bombarded specimens are presented. The conducted studies show that bombardment of structural materials with light ions can lead to significant structural damages and changes in the chemical and phase composition of the surface layer. The possible mechanisms of the changes in the chemical and phase composition include selective sputtering and radiation-induced accelerated diffusion of elements in the field of internal lateral stresses developing during the He + implantation process

  13. Comparison of low-cycle fatigue data of 2 1/4%CrMo steels

    International Nuclear Information System (INIS)

    Sanderson, S.J.; Petrequin, P.; Nieuwland, H.C.D.

    Data files have been produced on international strain-controlled fatigue information available for 2 1/4%CrMo steels; data assessment from these files is treated in three categories viz: annealed and isothermally annealed 2 1/4%Cr1%Mo steel; normalised and tempered and quenched and tempered 2 1/4%Cr1%Mo steel; and 2 1/4%CrMo variants. The available data have been considered generally in terms of total strain range vs. cycles to failure (Nsub(f)), tensile stress at Nsub(f)/2 vs. cycles to failure and time to failure vs. cycles to failure. Where possible the continuous cycling data have been statistically analysed in terms of the elastic and plastic strain components and cycles to failure to yield best-fit equations over defined temperature (T) regimes viz: T <= 427 deg. C, 427 deg. C < T <= 550 deg. C. and 550 deg. C < T <= 600 deg. C. The behaviour of the steels within the various classifications is discussed. (author)

  14. High-Temperature Corrosion of T92 Steel in N{sub 2}/H{sub 2}O/H{sub 2}S-Mixed Gas

    Energy Technology Data Exchange (ETDEWEB)

    Shi, Yuke; Kim, Min Jung; Park, Soon Yong; Abro, M. Ali; Yadav, Poonam; Lee, Dong Bok [Sungkyunkwan University, Suwon (Korea, Republic of)

    2016-06-15

    The ASTM T92 steel was corroded at 600 ℃ and 800 ℃ at 1 atm of N{sub 2}/3.1%H{sub 2}O/2.42%H{sub 2}S-mixed gas. The formed scales were thick and fragile. They consisted primarily of the outer FeS scale and the inner (FeS, FeCr{sub 2}S{sub 4})-mixed scale containing a small amount of the Cr{sub 2}O{sub 3} scale. This indicated that corrosion occurred mainly via sulfidation rather than oxidation due to the H{sub 2}S gas. Since FeS was present throughout the whole scale, T92 steel was non-protective, displaying high corrosion rates.

  15. Methodic recommendations on ultrasonic testing of pipeline austenitic butt joints

    International Nuclear Information System (INIS)

    Grebennik, V.S.; Lantukh, V.M.; Tajts, M.Z.; Ermolov, I.N.; Volkov, A.S.; Vyatskov, I.A.; Kesler, N.A.; Shchedrin, I.F.

    1989-01-01

    Recommendations for the application of ultrasonic testing of austenitic welded joints of the Du 500 pipelines with the walls 32-34 mm thick made of steel Kh18N10T are developed. The optimal values of the main parameters of ultrasonic testing are determined experimentally. Principles of calculation of the optimal parameters are considered. 1 ref.; 4 figs

  16. Kinetics of manganese in MAG/MIG welding with a 18/8/6 wire

    Directory of Open Access Journals (Sweden)

    Tušek, Janez

    2001-06-01

    Full Text Available The paper deals with a study of MAG/MIG welding of low-alloy ferritic steel and highalloy austenitic steel with a 18/8/6 wire. Manganese burn-off from the wire in welding a single-V butt weld was studied. It was found that manganese burns off in the arc during melting of a droplet at the wire end, and from the weld pool during weld formation. The range of manganese burn-off depends mainly on the type of shielding gas used and the arc length, i.e., from the arc voltage. The manganese burn-off increases with an increase of the content of active gases, i.e., CO2 and O2, in the neutral gas, i.e., argon. It also increases with an increase in arc voltage. The longer the welding arc, the longer exposition of the filler material to the welding arc and the wider the penetration, which allows manganese vapours to evaporate from the weld pool. The most important finding is that manganese burn-off from the 18/8/6 wire during welding of austenitic stainless steel with low-alloy ferritic steel is considerably strong, i.e., from 20% to 30%; nevertheless the wire concerned is perfectly suitable for welding of different types of steel.

    El artículo describe el estudio de un acero ferrítico poco aleado con un acero austenítico altamente aleado con el alambre 18/8/6 mediante el procedimiento MAG/MIG. Se ha investigado el consumo del manganeso del alambre durante la soldadura a tope con la preparación en V. Con los análisis se ha comprobado que el manganeso se consume en el arco desde la formación de la gota en la punta del alambre hasta la solidificación del metal aportado fundido. La cantidad perdida del manganeso depende, sobre todo, del tipo del gas de protección y de la longitud del arco, esto es, de la tensión convencional en el arco. Con el aumento de los gases activos (CO2 y O2 respecto al gas neutro argon, el consumo del manganeso va aumentando. También se observó que el consumo del manganeso va

  17. KENO-VA-PVM KENO-VA-SM, KENO5A for Parallel Processors

    International Nuclear Information System (INIS)

    Ramon, Javier; Pena, Jorge

    2002-01-01

    1 - Description of program or function: This package contains versions KENO-Va-SM (Shared Memory version) and KENO-Va-PVM (Parallel Virtual Machine version) based on SCALE-4.1. KENO-Va three-dimensional Boltzmann transport equation for neutron multiplying systems. The primary purpose of KENO-Va is to determine k-effective. Other calculated quantities include lifetime and generation time, energy-dependent leakages, energy- and region-dependent absorptions, fissions, fluxes, and fission densities. 2 - Method of solution: KENO-Va employs the Monte Carlo technique

  18. Study of radiation damage of steels for light water pressure vessels at UJV

    International Nuclear Information System (INIS)

    Vacek, N.; Stoces, B.

    1980-01-01

    Preoperational determination of radiation resistance of pressure vessel steels is performed at accelerated neutron exposure in a test or materials research reactor. The results obtained at accelerated and operating exposure are not fully identical and surveillance bodies are therefore used manufactured from the pressure vessel material. Currently, the following steels are used for the manufacture of light water reactor pressure vessels: Mn-Mo-Ni (ASTM-A533-B, ASTM-A508), Cr-Mo-V (15Kh2M1FA). At UJV Rez, for irradiation Chanca-M probes imported from France are used featuring electric temperature control. Almost identical radiation embrittlement was measured for all three steels after irradiation with a neutron fluence of 3x10 23 n.m -2 at a temperature of 290 degC. (H.S.)

  19. Composition of the spheroidal objects in KhN77TYuR-VD alloy

    International Nuclear Information System (INIS)

    Kotkis, M.A.; Nabutovskii, L.S.; Ostrov, A.E.; Zil'berman, A.G.

    1986-01-01

    The authors make an element analysis of the spheroidal objects in KhN77TYuR-VD alloy with the use of the energy dispersion microanalyzer with which the Stereoscan S-180 scanning electron microscope is equipped. Examples of the qualitative element analysis are shown. The results of the investigations show that the composition of the spheroidal inclusions includes nickel, chromium, titanium, iron, and also silicon and sulfur. The information obtained makes it possible to make an assumption on the mechanism of origin of these objects

  20. On effect of some thermodeformation parameters of welding cycle on tendency of pearlitic heat-resisting steels to fracture in reheating

    International Nuclear Information System (INIS)

    Prokhorov, N.N.; Bardokin, E.V.

    1979-01-01

    Studied is the inclination of the 12Kh1MF, 15Kh3M1F and N18K9M5T steels subject to thermodeformation cycle imitating a welding one, to fracture in reheating. A hot-rolled metal then subject to the same thermal treatment was used. The imitation of thermodeformation cycle of the welding permitted to vary maximum heating temperatures, the period during which the metal is kept at temperatures higher than 1100 deg C, and the cooling rate of ajacent zone metal. It is shown that the curve of the dependence of deformation ability and the tendency to fracture at the reheating of adjacent zone metal on the rate of its cooling at welding is U-shaped. Deformation ability has its maximum value at the cooling rate of 30 deg c/s in the range 1300 to 1000 deg C

  1. Unit rupture work as a criterion for quantitative estimation of hardenability in steel

    International Nuclear Information System (INIS)

    Kramarov, M.A.; Orlov, E.D.; Rybakov, A.B.

    1980-01-01

    Shown is possible utilization of high sensitivity of resistance to fracture of structural steel to the hardenability degree in the course of hardening to find the quantitative estimation of the latter one. Proposed is a criterion kappa, the ratio of the unit rupture work in the case of incomplete hardenability (asub(Tsub(ih))) under investigation, and the analoguc value obtained in the case of complete hardenability Asub(Tsub(Ch)) at the testing temperature corresponding to the critical temperature Tsub(100(M). Confirmed is high criterion sensitivity of the hardened steel structure on the basis of experimental investigation of the 40Kh, 38KhNM and 38KhNMFA steels after isothermal hold-up at different temperatures, corresponding to production of various products of austenite decomposition

  2. 40 CFR 721.10175 - 1-Propanaminium, N-(3-aminopropyl)-2-hydroxy-N,N-dimethyl-3-sulfo-, N-(C12-18 and C18-unsatd...

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false 1-Propanaminium, N-(3-aminopropyl)-2... 1-Propanaminium, N-(3-aminopropyl)-2-hydroxy-N,N-dimethyl-3-sulfo-, N-(C12-18 and C18-unsatd. acyl... chemical substance identified as 1-Propanaminium, N-(3-aminopropyl)-2-hydroxy-N,N-dimethyl-3-sulfo-, N-(C12...

  3. Comparison of SA508 Gr.3 and SA508 Gr.4N Low Alloy Steels for Reactor Pressure Vessel Steel

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Min Chul; Lee, B. S

    2009-12-15

    The microstructural characteristics and mechanical properties of SA508 Gr.3 Mn-Mo-Ni low alloy steel and SA508 Gr.4N Ni-Mo-Cr low alloy steel were investigated. The differences in the stable phases between these two low alloy steels were evaluated by means of a thermodynamic calculation using ThermoCalc. They were then compared to microstructural features and correlated with mechanical properties. Mn-Mo-Ni low alloy steel shows the upper bainite structure which has the coarse cementite in the lath boundaries. However, Ni-Mo-Cr low alloy steel shows the mixture of lower bainite and tempered martensite structure that homogeneously precipitates the small carbides such as M{sub 23}C{sub 6} and M{sub 7}C{sub 3} due to an increase of hardenability and Cr addition. In the mechanical properties, Ni-Mo-Cr low alloy steel has higher strength and toughness than Mn-Mo-Ni low alloy steel. Ni and Cr additions increase the strength by solid solution hardening. Besides, microstructural changes from upper bainite to tempered martensite improve the strength of the low alloy steel by grain refining effect. And the changes in the precipitation behavior by Cr addition improve the ductile-brittle transition behavior along with a toughening effect of Ni addition.

  4. Effect of Al Hot-Dipping on High-Temperature Corrosion of Carbon Steel in N2/0.1% H2S Gas

    Directory of Open Access Journals (Sweden)

    Muhammad Ali Abro

    2016-02-01

    Full Text Available High-temperature corrosion of carbon steel in N2/0.1% H2S mixed gas at 600–800 °C for 50–100 h was studied after hot-dipping in the aluminum molten bath. Hot-dipping resulted in the formation of the Al topcoat and the Al-Fe alloy layer firmly adhered on the substrate. The Al-Fe alloy layer consisted primarily of a wide, tongue-like Al5Fe2 layer and narrow Al3Fe layer. When corroded at 800 °C for 100 h, the Al topcoat partially oxidized to the protective but non-adherent α-Al2O3 layer, and the interdiffusion converted the Al-Fe alloy layer to an (Al13Fe4, AlFe3-mixed layer. The interdiffusion also lowered the microhardness of the hot-dipped steel. The α-Al2O3 layer formed on the hot-dipped steel protected the carbon steel against corrosion. Without the Al hot-dipping, the carbon steel failed by forming a thick, fragile, and non-protective FeS scale.

  5. A comparative study of the corrosion inhibition of mild steel in sulphuric acid by 4,4-dimethyloxazolidine-2-thione

    International Nuclear Information System (INIS)

    Musa, Ahmed Y.; Kadhum, Abdul Amir H.; Mohamad, Abu Bakar; Daud, Abdul Razak; Takriff, Mohd Sobri; Kamarudin, Siti Kartom

    2009-01-01

    The corrosion protection of mild steel in a 2.5 M H 2 SO 4 solution by 4,4-dimethyloxazolidine-2-thione (DMT) was studied at different temperatures by measuring changes in open circuit potential (OCP), potentiodynamic polarisation and electrochemical impedance spectroscopy (EIS). Corrosion current densities calculated from EIS data were comparable to those obtained from polarisation measurements. Results showed that DMT inhibited mild steel corrosion in a 2.5 M H 2 SO 4 solution and indicated that the inhibition efficiencies increased with the concentration of inhibitor, but decreased proportionally with temperature. Polarisation curves showed that DMT is a mixed-type inhibitor. Changes in impedance parameters suggested the adsorption of DMT on the mild steel surface, leading to the formation of protective films. The DMT adsorption on the mild steel surface followed the Langmuir adsorption isotherm. The kinetic and thermodynamic parameters for dissolution and adsorption were investigated. Comprehensive adsorption (physisorption and chemisorption) of the inhibitor molecules on the mild steel surface was suggested based on the thermodynamic adsorption parameters.

  6. Relationship between thermal embrittlement and hydrogen cracking in 18Ni(250) maraging steel

    International Nuclear Information System (INIS)

    Rack, H.J.

    1974-01-01

    The role of grain boundary precipitate structure on the stress corrosion susceptibility of 18Ni(250) maraging steel was examined. Varying solution treatment procedures were used to achieve either a precipitate-free grain boundary or one containing a high density of Ti(C,N) particles. The introduction of these treatments, although drastically affecting the monotonic fracture toughness, did not significantly alter the stress corrosion threshold in 100 percent relative humidity. These results are shown to be consistent with the previous suggestion that, under open circuit conditions, hydrogen-assisted cracking controls the environmental crack growth behavior of 18Ni maraging steels. (U.S.)

  7. Solvent-Mediated Synthesis of M(II-Coordination Polymer Part 1: Crystal Structure of Poly(1,2-di(4-pyridylethylene-k2N,N'-bis(1,4-benzenediacetato-k4O,O′,O′′,O′′'zinc(II], C22H18ZnN2O4

    Directory of Open Access Journals (Sweden)

    Stephen Adie Adalikwu

    2017-08-01

    Full Text Available An interaction of water-methanol solution of sodium1,4-benzenediacetate (bda and 4,4′-bipyridylethelene (bpee with aqueous solution of Zn(NO32·6H2O at room temperature yielded colourless crystals of 1 after three weeks in a sealed glass tube. The compound with composition C22H18ZnN2O4 crystallizes in monoclinic space group P21/c, with the following cell dimensions: a = 10.4566(2, b = 13.3085(2, c = 13.7189(2 Å, β = 101.491(1°. In the structure of 1, two Zn(II neighbours are connected by two bda ligands adopting chelating and bidentate-bridging coordination modes to form a dimeric unit (Zn2O8N4 with the Zn–Zn distance of 4.0432(6 Å. The carboxyl-bridged dimeric units are extended along the [001] direction by bpee co-ligands and further linked by bda ligand to form a three-dimensional network structure. The IR shows the characteristic bands of the carboxylates at 1611/1507 cm−1 and 1424/1373 cm−1, respectively, for asymmetric and symmetric stretching −CO2− vibrations. The separation ∆[νasym(CO2− − νsym(CO2−] values of 187 and 134 cm−1 are indicative of chelating and bidentate bridging coordination modes of the carboxylate to the metal centre.

  8. Comparison of mechanical behavior of TiN, TiNC, CrN/TiNC, TiN/TiNC films on 9Cr18 steel by PVD

    Science.gov (United States)

    Feng, Xingguo; Zhang, Yanshuai; Hu, Hanjun; Zheng, Yugang; Zhang, Kaifeng; Zhou, Hui

    2017-11-01

    TiN, TiNC, CrN/TiNC and TiN/TiNC films were deposited on 9Cr18 steel using magnetron sputtering technique. The morphology, composition, chemical state and crystalline structure of the films were observed and analyzed by X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and scanning electron microscopy (SEM). Hardness and adhesion force were tested by nanoindentation and scratch tester, respectively. The friction and wear behavior of TiN, TiNC, CrN/TiNC and TiN/TiNC films sliding against GCr15 balls were investigated and compared synthetically using ball-on-disk tribometer. It was found that Tisbnd N, Tisbnd C, Tisbnd Nsbnd C and Csbnd C bonds were formed. The TiN/TiNC film was composed of TiN, TiC and TiNC phases. Hardness and adhesion force results indicated that although the TiN film possessed the highest hardness, its adhesion force was lowest among all the films. Tribological test results showed that the friction coefficient of TiN/TiNC was much lower than that of TiN and the wear rate decreases remarkably from 2.3 × 10-15 m3/Nm to 7.1 × 10-16 m3/Nm, which indicated the TiN/TiNC film has better wear resistance.

  9. Radiosynthesis and biological evaluation of N-(2-[18F]fluoropropionyl)-3,4-dihydroxy-l-phenylalanine as a PET tracer for oncologic imaging.

    Science.gov (United States)

    Tang, Caihua; Nie, Dahong; Tang, Ganghua; Gao, Siyuan; Liu, Shaoyu; Wen, Fuhua; Tang, Xiaolan

    2017-07-01

    Several 11 C and 18 F labeled 3,4-dihydroxy-l-phenylalanine (l-DOPA) analogues have been used for neurologic and oncologic diseases, especially for brain tumors and neuroendocrine tumors PET imaging. However, 18 F-labeled N-substituted l-DOPA analogues have not been reported so far. In the current study, radiosynthesis and biological evaluation of a new 18 F-labeled l-DOPA analogue, N-(2-[ 18 F]fluoropropionyl)-3,4-dihydroxy-l-phenylalanine ([ 18 F]FPDOPA) for tumor PET imaging are performed. The synthesis of [ 18 F]FPDOPA was via a two-step reaction sequence from 4-nitrophenyl-2-[ 18 F]fluoropropionate ([ 18 F]NFP). The biodistribution of [ 18 F]FPDOPA was determined in normal Kunming mice. In vitro competitive inhibition and protein incorporation experiments were performed with SPC-A-1 lung adenocarcinoma cell lines. PET/CT studies of [ 18 F]FPDOPA were conducted in C6 rat glioma and SPC-A-1 human lung adenocarcinoma and H460 human large cell lung cancer-bearing nude mice. [ 18 F]FPDOPA was prepared with a decay-corrected radiochemical yield of 28±5% and a specific activity of 50±15GBq/μmol (n=10) within 125min. In vitro cell experiments showed that [ 18 F]FPDOPA uptake in SPC-A-1 cells was primarily transported through Na + -independent system L, with Na + -dependent system B 0,+ and system ASC partly involved in it. Biodistribution data in mice showed that renal-bladder route was the main excretory system of [ 18 F]FPDOPA. PET imaging demonstrated intense accumulation of [ 18 F]FPDOPA in several tumor xenografts, with (8.50±0.40)%ID/g in C6 glioma, (6.30±0.12)%ID/g in SPC-A-1 lung adenocarcinoma, and (6.50±0.10)%ID/g in H460 large cell lung cancer, respectively. A novel N-substituted 18 F-labeled L-DOPA analogue [ 18 F]FPDOPA is synthesized and evaluated in vitro and in vivo. The results support that [ 18 F]FPDOPA seems to be a potential PET tracer for tumor imaging, especially be a better potential PET tracer than [ 18 F]fluoro-2-deoxy-d-glucose ([ 18 F

  10. 18F-labelled N,N-dimethylamphetamine analogues for brain imaging studies

    International Nuclear Information System (INIS)

    Mathis, C.A.; Shulgin, A.T.; Yano, Y.; Sargent, T. III

    1986-01-01

    The radiochemical yields of nine N,N-dimethyl-2-(substituted phenyl)-isopropylamines (amphetamine analogues) were determined following reaction with [ 18 F]acetyl hypofluorite in a 0.1 M HCl solution at room temperature. The meta-dimethoxy substituted amphetamines gave the highest radiofluorination yields (24-32%, at EOB). Purification of the 18 F-labelled amphetamines was achieved in 10-20 min. 5- 18 F-2,4-Dimethoxy-N,N-dimethylamphetamine (5- 18 F-2,4-DNNA) was utilized to determine brain and lung uptake in rats. Positron emission tomography studies were conducted in a dog to determine the dynamic brain uptake and retention of this agent. The 5- 18 F-2,4-DNNA exhibited decreased initial uptake and more rapid loss of radioactivity in cerebral tissue compared to the iodinated homologue. (author)

  11. Study of corrosion resistance properties of nitrided carbon steel using radiofrequency N{sub 2}/H{sub 2} cold plasma process

    Energy Technology Data Exchange (ETDEWEB)

    Bouanis, F.Z. [Unite Materiaux et Transformations (UMET), Ingenierie des Systemes Polymeres, CNRS UMR 8207, ENSCL, BP 90108, F-59652 Villeneuve d' Ascq Cedex (France); Jama, C., E-mail: charafeddine.jama@ensc-lille.f [Unite Materiaux et Transformations (UMET), Ingenierie des Systemes Polymeres, CNRS UMR 8207, ENSCL, BP 90108, F-59652 Villeneuve d' Ascq Cedex (France); Traisnel, M. [Unite Materiaux et Transformations (UMET), Ingenierie des Systemes Polymeres, CNRS UMR 8207, ENSCL, BP 90108, F-59652 Villeneuve d' Ascq Cedex (France); Bentiss, F. [Laboratoire de Chimie de Coordination et d' Analytique, Faculte des Sciences, Universite Chouaib Doukkali, B.P. 20, M-24000 El Jadida (Morocco)

    2010-10-15

    C38 carbon steel have been plasma-nitrided using a radiofrequency cold plasma discharge treatment in order to investigate the influence of gas composition on corrosion behaviour of nitrided substrates. The investigated C38 steel was nitrided by a RF plasma discharge treatment using two different gas mixtures (75% N{sub 2}/25% H{sub 2} and 25% N{sub 2}/75% H{sub 2}) at different times of plasma-treatment on non-heated substrates. Electron Probe Microanalysis (EPMA) showed that the nitrided layer formed using 75% N{sub 2}/25% H{sub 2} gas mixture was thicker compared to those formed in the case of 25% N{sub 2}/75% H{sub 2} or pure N{sub 2}. The modifications of the corrosion resistance characteristics of plasma-nitrided C38 steel in 1 M HCl solution were investigated by weight loss measurements and ac impedance technique. The results obtained from these two evaluation methods were in good agreement. It was shown that the nitriding treatment in both cases (75% N{sub 2}/25% H{sub 2} and 25% N{sub 2}/75% H{sub 2}) improves the corrosion resistance of investigated carbon steel, while the better performance is obtained for the 75% N{sub 2}/25% H{sub 2} gas mixture. X-ray photoelectron spectroscopy (XPS) was carried out before and after immersion in corrosive medium in order to establish the mechanism of corrosion inhibition using N{sub 2}/H{sub 2} cold plasma nitriding process.

  12. Effects of inspired CO2, hyperventilation, and time on VA/Q inequality in the dog

    Science.gov (United States)

    Tsukimoto, K.; Arcos, J. P.; Schaffartzik, W.; Wagner, P. D.; West, J. B.

    1992-01-01

    In a recent study by Tsukimoto et al. (J. Appl. Physiol. 68: 2488-2493, 1990), CO2 inhalation appeared to reduce the size of the high ventilation-perfusion ratio (VA/Q) mode commonly observed in anesthetized mechanically air-ventilated dogs. In that study, large tidal volumes (VT) were used during CO2 inhalation to preserve normocapnia. To separate the influences of CO2 and high VT on the VA/Q distribution in the present study, we examined the effect of inspired CO2 on the high VA/Q mode using eight mechanically ventilated dogs (4 given CO2, 4 controls). The VA/Q distribution was measured first with normal VT and then with increased VT. In the CO2 group at high VT, data were collected before, during, and after CO2 inhalation. With normal VT, there was no difference in the size of the high VA/Q mode between groups [10.5 +/- 3.5% (SE) of ventilation in the CO2 group, 11.8 +/- 5.2% in the control group]. Unexpectedly, the size of the high VA/Q mode decreased similarly in both groups over time, independently of the inspired PCO2, at a rate similar to the fall in cardiac output over time. The reduction in the high VA/Q mode together with a simultaneous increase in alveolar dead space (estimated by the difference between inert gas dead space and Fowler dead space) suggests that poorly perfused high VA/Q areas became unperfused over time. A possible mechanism is that elevated alveolar pressure and decreased cardiac output eliminate blood flow from corner vessels in nondependent high VA/Q regions.

  13. Improved microstructure and properties of 12Cr2Ni4A alloy steel by vacuum carburization and Ti + N co-implantation

    Science.gov (United States)

    Dong, Meiling; Cui, Xiufang; Jin, Guo; Wang, Haidou; Cai, Zhaobing; Song, Shengqiang

    2018-05-01

    The carburized 12Cr2Ni4A alloy steel was implanted by Ti + N double elements implantation. The microstructure, nano-hardness and corrosion properties were investigated by EPMA, TEM, XPS, nano-hardness and electrochemistry tests in detail. The results showed that the Ti + N co-implanted layer is composed of FCC TiN and TiC phases with BCC martensite. Compared with the un-implanted layer, the Ti + N implanted layer has higher nano-hardness and better corrosion resistance. In addition, the higher nano-hardness was presented below the surface of 1800 nm compared with un-implanted layer, which is far beyond the thickness of the implanted layer. The results also indicated that the generation of nanoscale ceramic phase and structures are not the only factor to impose the influence on the nano-hardness and corrosion resistance, but the radiation damage and lattice distortion will play an important role.

  14. Is vaccenic acid (18:1t n-7) associated with an increased incidence of hip fracture? An explanation for the calcium paradox.

    Science.gov (United States)

    Hamazaki, Kei; Suzuki, Nobuo; Kitamura, Kei-Ichiro; Hattori, Atsuhiko; Nagasawa, Tetsuro; Itomura, Miho; Hamazaki, Tomohito

    2016-06-01

    High calcium intake may increase hip fracture (HF) incidence. This phenomenon, known as the calcium paradox, might be explained by vaccenic acid (18:1t n-7, VA), the highly specific trans fatty acid (TFA) present in dairy products. First, we ecologically investigated the relationship between 18:1 TFA intake and HF incidence using data from 12 to 13 European countries collected before 2000; then we measured the effects of VA and elaidic acid (18:1t n-9, EA) on osteoblasts from goldfish scales (tissues very similar to mammalian bone), with alkaline phosphatase as a marker; and finally we measured the effect of VA on mRNA expression in the scales for the major bone proteins type I collagen and osteocalcin. HF incidence was significantly correlated with 18:1 TFA intake in men (r=0.57) and women (r=0.65). Incubation with 1μmol/L VA and EA for 48h significantly decreased alkaline phosphatase activity by 25% and 21%, respectively. Incubation of scales with 10μmol/L VA for 48h significantly decreased mRNA expression for type I collagen and osteocalcin (by about 50%). In conclusion, VA may be causatively related to HF and could explain the calcium paradox. It may be prudent to reduce 18:1 TFA intake, irrespective of trans positions, to prevent HF. Copyright © 2016 Elsevier Ltd. All rights reserved.

  15. Tribological characteristics of Si3N4-based composites in unlubricated sliding against steel ball

    International Nuclear Information System (INIS)

    Liu, C.-C.; Huang, J.-L.

    2004-01-01

    The dry-sliding wear mechanism of Si 3 N 4 -based composites against AISI-52100 steel ball was studied using a ball-on-disc mode in a reciprocation motion. The addition of TiN particles can increase the fracture toughness of Si 3 N 4 -based composites. The fracture toughness of Si 3 N 4 -based composites played an important role for wear behavior. The Si 3 N 4 -based composites exhibits a small friction and wear coefficient compared to monolithic Si 3 N 4 . Atomic force microscopy (AFM) studies displayed fine wear grooves along the sliding traces. The subsurface deformation shows that the microcrack propagation extends along the TiN/Si 3 N 4 grain interface. The wear mechanisms were determined with scanning electron microscopy, transmission electron microscopy, X-ray diffraction and atomic force microscopy

  16. Fatigue damage evolution of cold-worked austenitic nickel-free high-nitrogen steel X13CrMnMoN18-14-3 (1.4452)

    Energy Technology Data Exchange (ETDEWEB)

    Tikhovskiy, I.; Weiss, S.; Fischer, A. [Univ. of Duisburg-Essen, Materials Science and Engineering II, Duisburg (Germany)

    2004-07-01

    Due to the fact that the risk of Ni-allergies becomes more and more important for modern therapies, the necessity of Ni-free implant materials becomes increasingly important. Beside Co- and Ti-base alloys Ni-free high-nitrogen steels may offer an attractive alternative. The present work presents the austenitic high-nitrogen and nickel-free steel X13CrMnMoN18-14-3, (Material No.: 1.4452) after 20% cold-working. In addition this material was deformed under axial cyclic total strain controlled fatigue tests at room temperature. The development of dislocation structure due to different loading amplitudes was compared to none cyclically deformed material. The good mechanical und fatigue properties of these austenitic high-nitrogen steels as well as the better tribological, chemical and biological properties compared to CrNiMo-steels qualify these steels as a promising alternative in medical applications. (orig.)

  17. Structural and phase studies of stainless wire after electroplastic drawing

    International Nuclear Information System (INIS)

    Troitskij, O.A.; Baldokhin, Yu.V.; Kir'yanchev, N.E.; Ryzhkov, V.G.; Kalugin, V.D.; Sokolov, N.V.; Klekovkin, A.A.; Klevtsur, S.A.

    1983-01-01

    Structural and phase properties of the 12Kh18N10T steel wire are studied after usual and electroplastic drawing from 0.40 up to 0.11 mm with 18-22% reduction per pass with passing 250 A/mm 2 electric current. The earlier made observation on a sharp decrease in content of deformation-induced martensite of α-phase takes place in the wire from stainless metastable austenitic steel as a result of electroplastic drawing. Distribution of the remained α-phase by the wire cross section is established

  18. Close toleranoe forging of chromium steel blades for powerful steam turbines

    International Nuclear Information System (INIS)

    Shastin, Eh.G.; Kositskij, Yu.N.; Lyubchits, G.A.

    1989-01-01

    Work on simulating technological process on die-forging hammer was performed in order to reduce the preparation period bringing technology of close tolerance forging of turbine blades to a commercial level. A special attention was paid to development of accurate forming of forgings of 20Kh13Sh, 12Kh13 and 15Kh11MFSh steels on screw presses with nominal effort equal to 80 and 144 MN

  19. Structure and properties of joints of two-ply steel using ''elastic'' explosives

    International Nuclear Information System (INIS)

    Gel'man, A.S.; Savel'ev, S.A.; Kulakevich, Ya.S.; Sharypov, N.A.; Drogovejko, I.Z.; Domolego, I.E.

    1980-01-01

    Some experimental data on structure and properties of compounds during cladding of sheets made of St3 with sheets of nichrome and steel 12Kh18N10T with the use of ''elastic'' explosives are presented. It is shown that the use of ''elastic'' explosives permits to decrease r parameter sufficiently, (where r - is the ratio of explosive mass to the mass of throwen phate) that reduces considerably the specific consumption explosives in comparison with the consumption conventional mixture explosives. Peculiarities of tested ''elastic'' explosives make their application perspective in two cases - at cladding of complex curved surfaces (drums, tube blanks etc.), as sell as at applications of burst chambers, where explosive mass limits dimensions of cladding blanks and details [ru

  20. 4-[18F]Fluorophenylpiperazines by Improved Hartwig-Buchwald N-Arylation of 4-[18F]fluoroiodobenzene, Formed via Hypervalent λ3-Iodane Precursors: Application to Build-Up of the Dopamine D4 Ligand [18F]FAUC 316

    Directory of Open Access Journals (Sweden)

    Fabian Kügler

    2014-12-01

    Full Text Available Substituted phenylpiperazines are often neuropharmacologically active compounds and in many cases are essential pharmacophores of neuroligands for different receptors such as D2-like dopaminergic, serotoninergic and other receptors. Nucleophilic, no-carrier-added (n.c.a. 18F-labelling of these ligands in an aromatic position is desirable for studying receptors with in vivo molecular imaging. 1-(4-[18F]Fluorophenylpiperazine was synthesized in two reaction steps starting by 18F-labelling of a iodobenzene-iodonium precursor, followed by Pd-catalyzed N-arylation of the intermediate 4-[18F]fluoro-iodobenzene. Different palladium catalysts and solvents were tested with particular attention to the polar solvents dimethylformamide (DMF and dimethylsulfoxide (DMSO. Weak inorganic bases like potassium phosphate or cesium carbonate seem to be essential for the arylation step and lead to conversation rates above 70% in DMF which is comparable to those in typically used toluene. In DMSO even quantitative conversation was observed. Overall radiochemical yields of up to 40% and 60% in DMF and DMSO, respectively, were reached depending on the labelling yield of the first step. The fluorophenylpiperazine obtained was coupled in a third reaction step with 2-formyl-1H-indole-5-carbonitrile to yield the highly selective dopamine D4 ligand [18F]FAUC 316.

  1. Effect of cryogenic treatment on the tensile behaviour of En 52 and 21-4N valve steels at room and elevated temperatures

    International Nuclear Information System (INIS)

    Jaswin, M. Arockia; Lal, D. Mohan

    2011-01-01

    Research highlights: → Tensile behaviour of cryo-treated valve steels are investigated at elevated temperature. → En 52 and 21-4N valve steel materials are treated at - 196 o C . → Tensile strength of cryo-treated En 52 and 21-4N valve steel has improved by 8 % and 12 % respectively. → Precipitation of fine carbides through cryogenic treatment is the reason for the improved strength. -- Abstract: This experimental study investigates the effects of cryogenic treatment on the tensile behaviour of En 52 and 21-4N valve steels at room and elevated temperatures. The materials are subjected to shallow cryogenic treatment (SCT) at 193 K and deep cryogenic treatment (DCT) at 85 K and the tensile behaviour is compared with that of the conventional heat treatment (CHT). The high temperature tensile test is conducted at 673 K (400 o C) and 923 K (650 o C) for the En 52 and 21-4N valve steels respectively. The ultimate tensile strength of the En 52 and 21-4N DCT samples show an enhancement of 7.87% and 6.76% respectively, over the CHT samples tested at the elevated temperature. The average yield strength of the En 52 DCT samples has an improvement 11% than that of the CHT samples when tested at room and elevated temperatures. The deep cryogenic treatment conducted at the optimized condition shows 7.84% improvement in the tensile strength for the En 52 valve steel and 11.87% improvement for the 21-4N valve steel when compared to the strength of the samples without the cryogenic treatment. A scanning electron microscopic analysis of the fracture surface indicates the presence of dimples and microvoid coalescence on the grain facets and interfaces of the cryo-treated specimens. The fracture surface of the deep cryo-treated 21-4N valve steel specimen shows a complete intergranular fracture with deep secondary cracks between the grains. On comparing the results of the percentage elongation, the cryo-treated samples show a smaller reduction in the elongation than that of the

  2. Account of internal friction when estimating recoverable creep strain

    International Nuclear Information System (INIS)

    Demidov, A.S.

    1986-01-01

    It is supposed that a difference of empirical and calculated data on the creep strain recovery for Kh18N10T steel under conditions of cyclic variations in stress is specified by the effect of internal friction. In the accepted model of creep β-flow is considered to be reversible and γ-flow- irreversible. Absorptivity is determined as a ratio of the difference between the expended work and work of strain recovery forces to the work expended in cycle. A notion of the equivalent stress acting in the period of the creep strain recovery is introduced. Results of the calculation according to the empirical formula where absorptivity was introduced into are compared with empirical data obtained for Kh18N10T steel at 750 deg C

  3. Sàng khôn as A Theorizing Tool in Mobility Education

    Directory of Open Access Journals (Sweden)

    Ngoc Ba Doan

    2017-02-01

    Full Text Available The current virtual and physical mobility of humans, ideas, knowledge and epistemologies has major implications for education, especially in settings where English is seen as the default medium of instruction. While diversity is inherent in mobility, English-only pedagogy is a denial of the richness and potential of diverse resources learners bring with them through their mobility. This paper reports a philosophical stance and pedagogical practices employed by a lecturer in English language education at an Australian university. It argues that students’ full linguistic resources and epistemologies, known as sàng khôn, contribute to their agency and can be used as tools to theorise new knowledge in the context of their mobility education.

  4. SCC growth behavior of stainless steel weld metals in high-temperature water. Influence of corrosion potential, weld type, thermal aging, cold-work and temperature

    International Nuclear Information System (INIS)

    Yamada, Takuyo; Terachi, Takumi; Miyamoto, Tomoki; Arioka, Koji

    2009-01-01

    Recent studies on crack growth rate measurement in oxygenated high-temperature pure water conditions, such as normal water chemistry in boiling water reactors, using compact tension type specimens have shown that weld stainless steels are susceptible to stress corrosion cracking. However, to our knowledge, there is no crack growth data of weld stainless steels in pressurized water reactor primary water. The principal purpose of this study was to examine the SCC growth behavior of stainless steel weld metals in simulated PWR primary water. A second objective was to examine the effect of (1) corrosion potential, (2) thermal-aging, (3) Mo in alloy and (4) cold-working on SCC growth in hydrogenated and oxygenated water environments at 320degC. In addition, the temperature dependence of SCC growth in simulated PWR primary water was also studied. The results were as follows: (1) No significant SCC growth was observed on all types of stainless steel weld metals: as-welded, aged (400degC x 10 kh) 308L and 316L, in 2.7 ppm-hydrogenated (low-potential) water at 320degC. (2) 20% cold-working markedly accelerated the SCC growth of weld metals in high-potential water at 320degC, but no significant SCC growth was observed in the hydrogenated water, even after 20% cold-working. (3) No significant SCC growth was observed on stainless steel weld metals in low-potential water at 250degC and 340degC. Thus, stainless steel weld metals have excellent SCC resistance in PWR primary water. On the other hand, (4) significant SCC growth was observed on all types of stainless steel weld metals: as-weld, aged (400degC x 10 kh) and 20% cold-worked 308L and 316L, in 8 ppm-oxygenated (high-potential) water at 320degC. (5) No large difference in SCC growth was observed between 316L (Mo) and 308L. (6) No large effect on SCC growth was observed between before and after aging up to 400degC for 10 kh. (7) 20% cold-working markedly accelerated the SCC growth of stainless steel weld metals. (author)

  5. Corrosion of carbon steel and low-alloy steel in diluted seawater containing hydrazine under gamma-rays irradiation

    International Nuclear Information System (INIS)

    Nakano, Junichi; Yamamoto, Masahiro; Tsukada, Takashi

    2014-01-01

    Seawater was injected into reactor cores of Units 1, 2, and 3 in the Fukushima Daiichi nuclear power station as an urgent coolant. It is considered that the injected seawater causes corrosion of steels of the reactor pressure vessel and primary containment vessel. To investigate the effects of gamma-rays irradiation on weight loss in carbon steel and low-alloy steel, corrosion tests were performed in diluted seawater at 50°C under gamma-rays irradiation. Specimens were irradiated with dose rates of 4.4 kGy/h and 0.2 kGy/h. To evaluate the effects of hydrazine (N 2 H 4 ) on the reduction of oxygen and hydrogen peroxide, N 2 H 4 was added to the diluted seawater. In the diluted seawater without N 2 H 4 , weight loss in the steels irradiated with 0.2 kGy/h was similar to that in the unirradiated steels, and weight loss in the steels irradiated with 4.4 kGy/h increased to approximate 1.7 times of those in the unirradiated steels. Weight loss in the steels irradiated in the diluted seawater containing N 2 H 4 was similar to that in the diluted seawater without N 2 H 4 . When N 2 was introduced into the gas phase in the flasks during gamma-rays irradiation, weight loss in the steels decreased. (author)

  6. Estimation of the Ultimate Tensile Strength of Steel from Its HB and HV Hardness Numbers and Coercive Force

    Science.gov (United States)

    Sandomirskii, S. G.

    2017-11-01

    A formula is derived to accurately describe the tabulated relation between the Brinell ( HB) and Vickers ( HV) hardnesses of steel over the entire range of their possible variation. This formula and the formulas describing the relation between the HB hardness of chromium-molybdenum and chromium-nickel steels and their ultimate tensile strength σu are used to analyze the change in σu of 38KhNM steel upon quenching and tempering. The data that reveal a relation between σu of 38KhNM steel and its coercive force are obtained.

  7. Nano/micro Sr{sub 2}Bi{sub 4}Ti{sub 5}O{sub 18} crystallites: Size dependent structural, second harmonic and piezoelectric properties

    Energy Technology Data Exchange (ETDEWEB)

    Tukaram, Shet; Bhimireddi, Rajasekhar; Varma, K.B.R., E-mail: kbrvarma@mrc.iisc.ernet.in

    2016-09-15

    Graphical abstract: Synthesis of Sr{sub 2}Bi{sub 4}Ti{sub 5}O{sub 18} nano/micro crystallites and their size dependent non-linear optical and piezoelectric responses. - Highlights: • Nano/microcrystallites of Sr{sub 2}Bi{sub 4}Ti{sub 5}O{sub 18} were synthesized via sol-gel route. • Crystallite size dependent structural and physical properties were studied. • SHG intensity (1.4 times that of KDP powder) from these crystallites was recorded. • PFM studies on isolated crystallite of 480 nm exhibited d{sub 33} as high as 27 pm/V. • Single domain nature of the crystallites below 160 nm was observed. - Abstract: Strontium bismuth titanate (Sr{sub 2}Bi{sub 4}Ti{sub 5}O{sub 18}) powders comprising crystallites of average sizes in the range of 94–1400 nm were prepared via citrate-assisted sol-gel route. With an increase in the average crystallite size there was a change in the lattice parameters and shift in the Raman vibration modes. Second harmonic signal (532 nm) intensity of the Sr{sub 2}Bi{sub 4}Ti{sub 5}O{sub 18} powders increased with the increase in the average crystallite size and the maximum intensity obtained in the reflection mode was 1.4 times as high as that of the powdered KH{sub 2}PO{sub 4}. Piezo Force Microscopic analyses carried out on isolated crystallite of size 74 nm, established a single domain nature with the coercive field as high as 347 kV/cm. There was a systematic increase in the d{sub 33} value with an increase in the size of the isolated crystallites and a high piezoelectric coefficient of ∼27 pm/V was obtained from an isolated crystallite of size 480 nm.

  8. Evaluation of the Precipitation Behavior in SA508 Gr. 4N Low Alloy Steel Using a Thermodynamic Calculation

    International Nuclear Information System (INIS)

    Park, Sang Gyu; Wee, Dang Moon; Kim, Min Chul; Lee, Bong Sang

    2007-01-01

    Low carbon low alloy steels, used as nuclear pressure vessels, steam generators and so on, hold a large portion of materials for nuclear power plants, and they are very important materials since they determine the safety and the life span of nuclear power plants. In addition, they are utilized for a long period under very severe conditions such as a high pressure, high temperature, neutron irradiation and corrosion, so they need a good combination of strength and toughness, a good weldability and an excellent neutron irradiation resistance and so on. SA508 Gr.3 steel shows the upper bainite microstructure, which is a less tough, so the steel is more difficult to obtain good toughness than to have good strength. And then, if a loss of toughness due to a neutron irradiation during service is considered, above all improving the toughness is important when a pressure vessel is fabricated It is known that a higher strength and fracture toughness of low alloy steels could be achieved by increasing the Ni and Cr contents. In this study, we have performed a thermodynamic calculation based on the microstructure of SA508 Gr.4N low alloy steel which has higher Ni and Cr contents than SA508 Gr.3 low alloy steel. Based on the microstructure/property relations obtained from literature research experimental works on SA508 Gr.4N steels, and by predicting the constitutional changes with alloying elements (such as Mn, Cr) during individual steps of a steel making process a using thermodynamic calculation, fundamental information for an alloy design have been discussed

  9. Nicotinic α4β2 receptor imaging agents. Part III. Synthesis and biological evaluation of 3-(2-(S)-azetidinylmethoxy)-5-(3′-18F-fluoropropyl)pyridine (18F-nifzetidine)

    International Nuclear Information System (INIS)

    Pichika, Rama; Easwaramoorthy, Balu; Christian, Bradley T.; Shi, Bingzhi; Narayanan, Tanjore K.; Collins, Daphne; Mukherjee, Jogeshwar

    2011-01-01

    Thalamic and extrathalamic nicotinic α4β2 receptors found in the brain have been implicated in Alzheimer's disease, Parkinson's disease, substance abuse and other disorders. We report here the development of 3-(2-(S)-azetidinylmethoxy)-5-(3′-fluoropropyl)pyridine (nifzetidine) as a new putative high-affinity antagonist for nicotinic α4β2 receptors. Nifzetidine in rat brain homogenate assays containing α4β2 sites labeled with 3 H-cytisine exhibited a binding affinity: Ki=0.67 nM. The fluorine-18 analog, 3-(2-(S)-azetidinylmethoxy)-5-(3′- 18 F-fluoropropyl)pyridine ( 18 F-nifzetidine), was synthesized in 20%–40% yield, and apparent specific activity was estimated to be above 2 Ci/μmol. Rat brain slices indicated selective binding of 18 F-nifzetidine to thalamus, subiculum, striata, cortex and other regions consistent with α4β2 receptor distribution. This selective binding was displaced >85% by 150 μM nicotine. Positron emission tomography (PET) imaging studies of 18 F-nifzetidine in anesthetized rhesus monkey showed slow uptake in the various brain regions. Retention of 18 F-nifzetidine was maximal in the thalamus and lateral geniculate followed by regions of the temporal and frontal cortex. Cerebellum showed the least uptake. Thalamus to cerebellum ratio was about 2.3 at 180 min postinjection and continued to rise. 18 F-Nifzetidine shows promise as a new PET imaging agent for α4β2 nAChR. However, the slow kinetics suggests a need for >3-h PET scans for quantitative studies of the α4β2 nAChRs.

  10. [μ-N,N′-Bis(2-aminoethylethane-1,2-diamine-κ4N1,N1′:N2,N2′]bis{[N,N′-bis(2-aminoethylethane-1,2-diamine-κ4N,N′,N′′,N′′′]cadmium} tetrakis(perchlorate

    Directory of Open Access Journals (Sweden)

    Hamid Goudarziafshar

    2012-09-01

    Full Text Available The centrosymmetric dinuclear cadmium title complex, [Cd2(C6H18N43](ClO44, was obtained by the reaction of N,N′-bis(2-aminoethylethane-1,2-diamine (trien with Cd(NO32·4H2O and sodium perchlorate in methanol. The CdII cation is coordinated by four N atoms of a non-bridging trien ligand and by two N atoms of a bridging trien ligand in a slightly distorted octahedral coordination geometry. The bridging ligand shares another two N atoms with a neighboring symmetry-equivalent CdII cation. The structure displays C—H...O and N—H...O hydrogen bonding. The perchlorate anion is disordered over two sets of sites in a 0.854 (7: 0.146 (7 ratio.

  11. Proposal for the Award of a Contract for the Supply of 18kV Power Transformers Rated 464 kVA to 2 MVA

    CERN Document Server

    2002-01-01

    This document concerns the award of a contract for the supply of thirty-five 18 kV cast-resin rectifier power transformers rated 464 kVA to 2 MVA and 26 protective enclosures. Following a market survey (MS-2920/SL/LHC) carried out among 56 firms in sixteen Member States, a call for tenders (IT-3007/SL/LHC) was sent on 12 August 2002 to eight firms in five Member States. By the closing date, CERN had received three tenders from three firms in three Member States. The Finance Committee is invited to agree to the negotiation of a contract with TRASFOR (CH), the lowest bidder, for the supply of 35 power transformers rated 464 kVA to 2 MVA and 26 protective enclosures for a total amount of 1 398 500 Swiss francs, not subject to revision, with an option for three additional transformers and protective enclosures, for an additional amount of 107 650 Swiss francs, subject to revision for inflation from 1 January 2005, bringing the total amount to 1 506 150 Swiss francs subject to revision for inflation from 1 January...

  12. Radiolabelling of isopeptide N epsilon-(gamma-glutamyl)-L-lysine by conjugation with N-succinimidyl-4-[18F]fluorobenzoate.

    Science.gov (United States)

    Wüst, F; Hultsch, C; Bergmann, R; Johannsen, B; Henle, T

    2003-07-01

    The isopeptide N(epsilon)-(gamma-glutamyl)-L-lysine 4 was labelled with 18F via N-succinimidyl-4-[18F]fluorobenzoate ([18F]SFB). A modified approach for the convenient synthesis of [18F]SFB was used, and [18F]SFB could be obtained in decay-corrected radiochemical yields of 44-53% (n = 20) and radiochemical purity >95% within 40 min after EOB. For labelling N(epsilon)-(gamma-glutamyl)-L-lysine with [18F]SFB the effects of isopeptide concentration, temperature, and pH were studied to determine the optimum reaction conditions. The coupling reaction was shown to be temperature and pH independent while being strongly affected by the isopeptide concentration. Using the optimized labelling conditions, in a typical experiment 1.3GBq of [18F]SFB could be converted into 447MBq (46%, decay-corrected) of [18F]fluorobenzoylated isopeptide within 45 min, including HPLC purification.

  13. Insights into the photocatalytic mechanism of mediator-free direct Z-scheme g-C3N4/Bi2MoO6(010) and g-C3N4/Bi2WO6(010) heterostructures: A hybrid density functional theory study

    Science.gov (United States)

    Opoku, Francis; Govender, Krishna Kuben; Sittert, Cornelia Gertina Catharina Elizabeth van; Govender, Penny Poomani

    2018-01-01

    Graphite-like carbon nitride (g-C3N4)-based heterostructures have received much attention due to their prominent photocatalytic activity. The g-C3N4/Bi2WO6 and g-C3N4/Bi2MoO6 heterostructures, which follow a typical hetero-junction charge transfer mechanisms show a weak potential for hydrogen evolution and reactive radical generation under visible light irradiation. A mediator-free Z-scheme g-C3N4/Bi2MoO6(010) and g-C3N4/Bi2WO6(010) heterostructures photocatalyst are designed for the first time using first-principles studies. Moreover, theoretical understanding of the underlying mechanism, the effects of interfacial composition and the role the interface play in the overall photoactivity is still unexplained. The calculated band gap of the heterostructures is reduced compared to the bulk Bi2WO6 and Bi2MoO6. In this study, we systematically calculated energy band structure, optical properties and charge transfer of the g-C3N4/Bi2MoO6(010) and g-C3N4/Bi2WO6(010) heterostructures using the hybrid density functional theory approach. The results show that the charge transfer at the interface of the heterostructures induces a built-in potential, which benefits the separation of photogenerated charge carriers. The g-C3N4/Bi2MoO6(010) heterostructure with more negative adhesion energy (-1.10 eVA-2) is predicted to have a better adsorptive ability and can form more easily compared to the g-C3N4/Bi2WO6(010) interface (-1.16 eVA-2). Therefore, our results show that the g-C3N4 interaction with Bi2MoO6 is stronger than Bi2WO6, which is also verified by the smaller vertical separation (3.25 Å) between Bi2MoO6 and g-C3N4 compared to the g-C3N4/Bi2WO6(010) interface (3.36 Å). The optical absorption verifies that these proposed Z-scheme heterostructures are excellent visible light harvesting semiconductor photocatalyst materials. This enhancement is ascribed to the role of g-C3N4 monolayer as an electron acceptor and the direct Z-scheme charge carrier transfer at the interface of

  14. Slag inclusions in vacuum-melted ingots of the KhN73MBTYu nickel base alloy

    International Nuclear Information System (INIS)

    Gorin, V.A.; Kleshchev, A.S.; Kazharskaya, L.P.

    1977-01-01

    Three types of slag inclusions in ingots of the vacuum-arc-remelted nickel alloy KhN73MBTYu are considered. Type 1 inclusions are those in the surface zone; type 2 inclusions are agglomerations of nitrides and oxides formed due to the fall of lining slag; type 3 inclusions consist of agglomerations of nitrides and oxides as a result of interaction of dissolved oxygen and nitrogen with melt components. The inclusions are removed by machining of the lateral surface. It should be noted that the presence of a large amount of slag on the surface of the molten pool adversely affects the stability of the electrical regime of melting. Strict adherence to the recommendations on the melting and pouring of the initial metal reduces the pollution of the consumable electrode with nonmetallic inclusions

  15. Effect of N+Cr alloying on the microstructures and tensile properties of Hadfield steel

    International Nuclear Information System (INIS)

    Chen, C.; Zhang, F.C.; Wang, F.; Liu, H.; Yu, B.D.

    2017-01-01

    The microstructures and tensile behaviors of traditional Hadfield steel, named Mn12 steel, and Hadfield steel alloyed with N+Cr, named Mn12CrN steel were studied through optical microscopy, transmission electron microscopy, and scanning electron microscopy, among others. Three different tensile strain rates of 5×10 −4 , 5×10 −3 , and 5×10 −2 s −1 were selected in the tensile test. The deformation microstructures and fracture morphologies of the two steels after fracture in the tensile test were observed to analyze the tensile deformation response to different tensile strain rates. Results showed that the grain size of Mn12CrN steel was evidently refined after alloying with N+Cr. The grain would not become abnormally coarse even with increasing austenitizing temperature. During tensile deformation, the strength and plasticity of Mn12CrN steel were superior to those of Mn12 steel at the same strain rate. With increasing the strain rate, the changes in strength and plasticity of Mn12CrN steel were less sensitive to tensile strain rate compared with Mn12 steel. The effects of grain refinement and N+Cr alloying on dynamic strain aging and deformation twining behaviors were responsible for this lack of sensitivity to strain rate.

  16. Study on salt bath nitrocarburizing of 17-4PH stainless steel

    International Nuclear Information System (INIS)

    Wang Jun; Xiong Ji; Fan Hongyuan; Peng Qian; Wang Ying; Li Guijiang; Shen Baoluo

    2009-01-01

    The effect of the salt bathing nitriding under different temperature on the microstructure of Martensite stainless steel and the change of hardness and wear ability under different treatment temperature are comparatively studied. The study results show that when 17-4PH stainless steel was subjected to the salt bathing nitriding, the main items in the nitrided layer are the expanded (nitride contended) martensite (α'), Fe 2-3 (N, C), CrN, Fe 4 N and Fe 3 O 4 . The amount of Fe 3 O 4 and CrN was increased with the treatment temperature going up. The lattice constant of expanded martensite has the similar change. The activation energy of nitriding in this salt bath was 190.9 kJ/mol. The depth of the nitrided layer was increased with the treatment temperature increasing. After the alloy nitriding at 580 degree C, the mass loss in the slide wear test was reduced from 21.1 mg for H 1100 condition to 1.0 mg. (authors)

  17. Molecular Nickel Phosphide Carbonyl Nanoclusters: Synthesis, Structure, and Electrochemistry of [Ni11P(CO)18]3- and [H6-nNi31P4(CO)39]n- (n = 4 and 5).

    Science.gov (United States)

    Capacci, Chiara; Ciabatti, Iacopo; Femoni, Cristina; Iapalucci, Maria Carmela; Funaioli, Tiziana; Zacchini, Stefano; Zanotti, Valerio

    2018-02-05

    The reaction of [NEt 4 ] 2 [Ni 6 (CO) 12 ] in thf with 0.5 equiv of PCl 3 affords the monophosphide [Ni 11 P(CO) 18 ] 3- that in turn further reacts with PCl 3 resulting in the tetra-phosphide carbonyl cluster [HNi 31 P 4 (CO) 39 ] 5- . Alternatively, the latter can be obtained from the reaction of [NEt 4 ] 2 [Ni 6 (CO) 12 ] in thf with 0.8-0.9 equiv of PCl 3 . The [HNi 31 P 4 (CO) 39 ] 5- penta-anion is reversibly protonated by strong acids leading to the [H 2 Ni 31 P 4 (CO) 39 ] 4- tetra-anion, whereas deprotonation affords the [Ni 31 P 4 (CO) 39 ] 6- hexa-anion. The latter is reduced with Na/naphthalene yielding the [Ni 31 P 4 (CO) 39 ] 7- hepta-anion. In order to shed light on the polyhydride nature and redox behavior of these clusters, electrochemical and spectroelectrochemical studies were carried out on [Ni 11 P(CO) 18 ] 3- , [HNi 31 P 4 (CO) 39 ] 5- , and [H 2 Ni 31 P 4 (CO) 39 ] 4- . The reversible formation of the stable [Ni 11 P(CO) 18 ] 4- tetra-anion is demonstrated through the spectroelectrochemical investigation of [Ni 11 P(CO) 18 ] 3- . The redox changes of [HNi 31 P 4 (CO) 39 ] 5- show features of chemical reversibility and the vibrational spectra in the ν CO region of the nine redox states of the cluster [HNi 31 P 4 (CO) 39 ] n- (n = 3-11) are reported. The spectroelectrochemical investigation of [H 2 Ni 31 P 4 (CO) 39 ] 4- revealed the presence of three chemically reversible reduction processes, and the IR spectra of [H 2 Ni 31 P 4 (CO) 39 ] n- (n = 4-7) have been recorded. The different spectroelectrochemical behavior of [HNi 31 P 4 (CO) 39 ] 5- and [H 2 Ni 31 P 4 (CO) 39 ] 4- support their formulations as polyhydrides. Unfortunately, all the attempts to directly confirm their poly hydrido nature by 1 H NMR spectroscopy failed, as previously found for related large metal carbonyl clusters. Thus, the presence and number of hydride ligands have been based on the observed protonation/deprotonation reactions and the spectroelectrochemical

  18. Behaviour of glass and thermal protective coatings on stainless steels in the nitrogen tetroxide based coolant

    International Nuclear Information System (INIS)

    Bakalin, Yu.I.; Dobrunova, V.M.; Doroshkevich, V.N.; Nesterenko, V.B.; Trubnikov, V.P.

    1985-01-01

    The technology of application of glass and enamel protective coatings on stainless steel has been examined, their testing in the medium of nitrogen tetroxide based coolant with different content of nitric acid has been carried out, the basic characteristics of the coatings after testing have been defined. Chromium-nickel austenitic 12kh18n10t steel, widely used in the nuclear power, have been chosen as a basic object of examination. The coatings have been tested in nitrogen oxide at P=12.0 MPa, temperature 310 deg C and 0.1% HNO 3 , and also in the medium of vat residue of the rectifying tower with nitric acid content up to 25 mass %. Tests of the coatings have demonstrated their sufficiently high stability, especially of those based on enamels A-20 and BK-5. These coatings are characterised by satisfactory performance and can be used for corrosion protection of the materials used in nuclear power

  19. PENDIDIKAN KARAKTER MENURUT KH. WAHID HASYIM

    Directory of Open Access Journals (Sweden)

    Rangga Sa’adillah S. A. P.

    2015-11-01

    Full Text Available This library research examined two research questions. They are what thoughts of KH. Wahid Hasyim about the character education are and how the concept of character education by KH. Wahid Hasyim is relevant to the current condition of education in Indonesia. This study reveals two findings through an inductive analysis. The chief finding of this study is that there are eight characteristic values taught by KH.Wahid Hasyim including religious, tolerant, independent, democratic, patriotic, nasionalist, communicative, and keen on reading. Second, this study disclosed that the thought of character education by KH. Wahid Hasyim is in line with the goal of character education. He strove to build a multicultural national life, educate an intelligent civilization, build a noble character, encourage people to contribute to the development of human life, and develop the potential of having kind hearts, positive thoughts and good behavior as well as exemplary models. He also sought to generate enthusiasm of citizens to keep the peace, creativity, independence, and to be able to coexist with other nations in a harmony.

  20. Carbon transfer between 2 1/4 Cr 1 Mo alloy and austenitic steels (experiments in anisothermal loops)

    International Nuclear Information System (INIS)

    Baque, P.; Besson, M.; Champeix, L.; Donati, J.R.; Oberlin, C.; Saint-Paul, P.

    1976-01-01

    Studies on carbon transfer between the ferritic steel 2 1/4 Cr 1 Mo and the austenitic steels 316L and 321H have shown that there is not any measurable carbon transfer in the operating conditions of the secondary circuit of PHENIX (475 deg C was the maximal temperature of the 2 1/4 Cr 1 Mo steel). A significant carbon transfer has been observed between the ferritic steel and the 316L steel when the 321H was replaced by the 2 1/4 Cr 1 Mo steel in the same thermohydraulic conditions (the ferritic steel was then used up to 545 deg C). This experiment has demonstrated the importance of the temperature and the initial carbon content of the ferritic steel as parameters in the decarburization process. It appears that decarburization may not be sensitive to the thermohydraulic conditions at least in the range investigated in those experiments. In the other hand the 316L steel is observed to have been carburized, the degree of carburization remaining appreciably constant and independent on the temperature between 400 deg C and 550 deg C [fr

  1. Effect of surface reactions on steel, Al{sub 2}O{sub 3} and Si{sub 3}N{sub 4} counterparts on their tribological performance with polytetrafluoroethylene filled composites

    Energy Technology Data Exchange (ETDEWEB)

    Shen, J.T.; Top, M. [Materials Innovation Institute M2i, Department of Applied Physics, Zernike Institute for Advanced Materials, University of Groningen, Nijenborgh 4, 9747 AG Groningen (Netherlands); Ivashenko, O.; Rudolf, P. [Department of Surfaces and Thin Films, Zernike Institute for Advanced Materials, University of Groningen, Nijenborgh 4, 9747 AG Groningen (Netherlands); Pei, Y.T., E-mail: y.pei@rug.nl [Materials Innovation Institute M2i, Department of Applied Physics, Zernike Institute for Advanced Materials, University of Groningen, Nijenborgh 4, 9747 AG Groningen (Netherlands); Department of Advanced Production Engineering, Engineering and Technology Institute Groningen, University of Groningen, Nijenborgh 4, 9747 AG Groningen (Netherlands); De Hosson, J.Th.M., E-mail: j.t.m.de.hosson@rug.nl [Materials Innovation Institute M2i, Department of Applied Physics, Zernike Institute for Advanced Materials, University of Groningen, Nijenborgh 4, 9747 AG Groningen (Netherlands)

    2015-03-15

    Highlights: • The influence of surface reactions with PTFE on the tribo-performance of different counterparts is revealed. • Experiments confirm that friction can be greatly reduced by two F-terminated surfaces sliding over each other. • Al−F and Fe−F chemical bonding form on the surface of alumina and steel counterpart balls during sliding against PTFE-containing composite. • No Si−F bonding formed on Si{sub 3}N{sub 4} ball under the same condition, leading to higher friction and wear. - Abstract: The influence of surface reactions on the tribo-performance of steel, Al{sub 2}O{sub 3} and Si{sub 3}N{sub 4} balls sliding against polytetrafluoroethylene/SiO{sub 2}/epoxy composites was investigated. Al{sub 2}O{sub 3} ball were found to exhibit the best tribo-performance, namely a low coefficient of friction and the lowest wear rates of both the composites and the counterpart ball, when sliding against the PTFE filled composites. The difference in the tribo-performance of the Al{sub 2}O{sub 3} ball and the Si{sub 3}N{sub 4} ball can neither be attributed to the different morphology of the worn composite surfaces nor to the amount of PTFE transferred onto the wear surfaces. Instead we found that the friction is greatly reduced in the case of the Al{sub 2}O{sub 3} ball because two fluoro-terminated surfaces are sliding over each other; in fact, the formation of Al−F bonding was confirmed by X-ray photoelectron spectroscopy.

  2. Estudio serológico y de protección en ratones utilizando diferentes esquemas y dosis de VA-MENGOC-BC®

    Directory of Open Access Journals (Sweden)

    Juan F. Infante

    2001-06-01

    Full Text Available La alta incidencia mundial de meningitis meningocócica por Neisseria meningitidis serogrupo B (N. meningitidis movilizó los recursos de la ciencia hacia su enfrentamiento en un período corto de tiempo. Para el estudio de esta enfermedad fue imprescindible desarrollar modelos experimentales que posibilitaran caracterizar no sólo la capacidad inmunogénica y protectora de los candidatos vacunales, sino también la toxigenicidad del producto. El estudio basado en el modelo ratón Balb/c con la utilización de factores estimulantes de la virulencia, posibilitó el desarrollo experimental de la enfermedad. Consistió en la aplicación de diferentes esquemas de dosis y diluciones de la vacuna (1/2, 1/4, 1/8, 1/16 en solución salina fisiológica 0,85%. Se conformaron 15 grupos de ocho animales cada uno que previamente recibieron Dextrana Férrica (IMEFA y mucina gástrica de cerdo 8% en un volumen total de 0,4 mL, y un grupo control al que le fue administrada la vacuna pura. Se empleó para el reto la cepa 385 de N. meningitidis con una concentración del inóculo de 107 UFC/mL. El esquema de vacunación contempló grupos vacunados con 1, 2, y 3 dosis a los 0,15 y 30 días. Se administraron 0,2 mL del inóculo de N. meningitidis por vía intraperitoneal. Se determinó la dosis letal media (DL50, anticuerpos bactericidas, respuesta serológica por el método de ELISA y se calculó la protección conferida. Se aplicó el método de Log rank para la comparación de los tiempos de sobrevivencia y para el ensayo de ELISA se aplicó el método de superficie ajustada por SPLINE. Hemos demostrado la utilidad del biomodelo ratón Balb/c para comprobar la eficacia de la vacuna VA-MENGOC-BC®. Quedó demostrada la correlación entre los niveles de anticuerpos y la protección conferida por la vacuna, comprobándose además por los ensayos de reto. Se logró obtener una aproximación con respecto a los límites de eficacia de VA-MENGOC-BC® mediante

  3. The structure of the alphinizing coat on alloy steels

    Directory of Open Access Journals (Sweden)

    S. Pietrowski

    2008-12-01

    Full Text Available In this paper results of the structure of the coat alphinizing in AlSi5 silumin on alloy steels: acid-proof 1H18N9T (X6CrNiTi18-10 and high speed SW18 (HS18-0-1 were presented. The temperature of the alphinizing bath was amounts to750±5°C, and immersion time of the element τ = 180s. It was shown, that there is the different “g” coat thickness on testing steels. On the 1H18N9T steel it amounts to g = 52μm, and on the SW18 steel – g = 203μm. Regardless of a grade of testing alloy steels the coat consist of three layers with diversified phasic structure. There is different chemical composition of coat layers on testing steels. The first layer from the base consist of AlFe phase containing alloy addictions of steels: Cr and Ni (1H18N9T and W, V and Cr (SW18. On this layer crystallize the second layer of intermetallic phases. It is the phase containing the main alloy addiction of steels: AlFeCr (1H18N9T and AlFeW (SW18. The last, outside layer consist of silumin containing AlFeNi intermetallic phases on the 1H18N9T steel and AlFeW on the SW18 steel. Regardless of the grade of testing steels there is Si element in all layers of the coat. There are morphological differences in tested layers. The second layer (AlFeW phase inside the coat on the SW18 steel consist of faced crystals growing into in outside silumin layer. On the 1H18N9T steel a boundary between transient and outside layer is more uniform. Free separations of intermetallic phases inside silumin layer on the 1H18N9T steel have lamellar and on the SW18 steel – faced form.

  4. Corrosion critique of the 2 1/4 Cr--1 Mo steel for LMFBR steam generation system applications

    International Nuclear Information System (INIS)

    Zima, G.E.

    1977-07-01

    The unstabilized ferritic steel of nominal composition, 2 1 / 4 Cr-1Mo, has been proposed for critical structural assignments in LMFBR powerplants, specifically: the tubing, tubesheet and shell of the evaporator and superheater components. The interest in this steel has been based on a presumably favorable general corrosion property spectrum, acceptable mechanical properties and fabricability, and certain economies associated with the low alloy content. This report is an attempt at a general corrosion assessment for the 2 1 / 4 Cr-1Mo steel and an identification of corrosion problem areas potential to this steel from the sodium and water/steam systems of the proposed working environment. There is a considerable area of uncertainty in the sodium-side response of 2 1 / 4 Cr-1Mo steel, centered in the loss and redisposition of carbon during long-term exposure to sodium of various impurity backgrounds. It is submitted that present evidence relating to the water/steam-side corrosion behavior of the 2 1 / 4 Cr-1Mo steel, under nominal and conceivable perturbed environmental conditions, constitutes the principal concern for the proposed LMFBR powerplant applications of this steel. It is suggested that this unfavorable corrosion aspect represents an inherent limitation of the low alloy content of this steel, probably largely independent of melting and processing recourses, and it is a sufficient basis to question the incentive for a continuation of the collateral studies of this steel for the proposed LMFBR steam generation system assignments

  5. Enhancement of strength properties of hot rolled 10KHSND steel

    International Nuclear Information System (INIS)

    Nasibov, A.G.; Popova, L.V.; Pikulin, S.A.; Globa, N.I.

    1989-01-01

    To find out the reasons of low hot rolling yield for 10KhSND steel sheets in mechanical properties, titanium effect in the range of 0.008-0.03% concentrations is studied. It is established that the titanium content in a solid solution is conserved within 0.003-0.005%, the rest of titanium is bound to carbonitrides Ti(C, N). It is shown that alloys with 0.025-0.03% titanium content possess the increased values of ultimate and yield strength the necessary level of impact strength and good wealdability. The good steel yield, when the titanium content is sustained at the given level, increases from 40 to 85%

  6. Composition and corrosion properties of high-temperature oxide films on steel type 18-10

    International Nuclear Information System (INIS)

    Vakulenko, B.F.; Morozov, O.N.; Chernysheva, M.V.

    1985-01-01

    The composition and propeties of oxide films, formed in the process of tube production of steel type 18-10, as well as the behaviour of the steels coated with oxide films under operating conditions of NPP heat-exchange equipment at the 20-300 deg C temperatures are determined. It is found, that the films have a good adhesion to the steel surface and repeat the metal structure without interfering with, the surface defect determination. Introduction of the NaNO 2 corrosion inhibitor decreases the film destruction rate to the level of the base metal corrosion. It is found acceptable to use tubes of steel 18-10 coated with dense oxide films in the heat-exchange and water supply systems of NPP

  7. Effect of N+Cr alloying on the microstructures and tensile properties of Hadfield steel

    Energy Technology Data Exchange (ETDEWEB)

    Chen, C. [State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004 (China); Zhang, F.C., E-mail: zfc@ysu.edu.cn [State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004 (China); National Engineering Research Center for Equipment and Technology of Cold Strip Rolling, Yanshan University, Qinhuangdao 066004 (China); Wang, F. [State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004 (China); Liu, H.; Yu, B.D. [China Railway Shanhaiguan Bridge Group Co. LTD, Qinhuangdao 066205 (China)

    2017-01-02

    The microstructures and tensile behaviors of traditional Hadfield steel, named Mn12 steel, and Hadfield steel alloyed with N+Cr, named Mn12CrN steel were studied through optical microscopy, transmission electron microscopy, and scanning electron microscopy, among others. Three different tensile strain rates of 5×10{sup −4}, 5×10{sup −3}, and 5×10{sup −2} s{sup −1} were selected in the tensile test. The deformation microstructures and fracture morphologies of the two steels after fracture in the tensile test were observed to analyze the tensile deformation response to different tensile strain rates. Results showed that the grain size of Mn12CrN steel was evidently refined after alloying with N+Cr. The grain would not become abnormally coarse even with increasing austenitizing temperature. During tensile deformation, the strength and plasticity of Mn12CrN steel were superior to those of Mn12 steel at the same strain rate. With increasing the strain rate, the changes in strength and plasticity of Mn12CrN steel were less sensitive to tensile strain rate compared with Mn12 steel. The effects of grain refinement and N+Cr alloying on dynamic strain aging and deformation twining behaviors were responsible for this lack of sensitivity to strain rate.

  8. Positron annihilation and Moessbauer studies of neutron irradiated reactor pressure vessel steels

    International Nuclear Information System (INIS)

    Brauer, G.; Matz, W.; Liszkay, L.; Molnar, B.

    1990-11-01

    Positron annihilation (lifetime, Doppler broadening) and Moessbauer studies on unirradiated, neutron irradiated and neutron irradiated plus annealed reactor pressure vessel steels (Soviet type 15Kh2NMFA) are presented. The role of microstructural properties and the formation of irradiation-induced precipitates is discussed. (orig.) [de

  9. Effects of sodium environment on the mechanical properties of Fe-2 1/4Cr-1Mo steel

    International Nuclear Information System (INIS)

    Chopra, O.K.

    Mechanical property data on isothermally annealed, thermally aged, and sodium-exposed Fe-2 1/4Cr-1Mo steel are analyzed to evaluate the influence of the sodium environment as well as the effects of the microstructural and compositional changes that occur in the steel during long-term exposure to sodium. Correlations are developed to predict the environmental effects on tensile, creep, fatigue, and creep-fatigue properties of Fe-2 1/4Cr-1Mo steel in sodium. The results indicate that at temperatures <823 K (550 deg. C), degradation of mechanical properties is essentially due to thermal aging. Loss of carbon from the steel reduces both the tensile and creep-rupture strength, but has little or no effect on the fatigue properties. The cyclic properties of Fe-2 1/4Cr-1Mo steel in sodium are superior to those in air. The creep-fatigue behaviour in sodium is significantly different from that in an air environment. The creep-fatigue data are analyzed using the interactive damage rate equations to predict the time-dependent fatigue bahaviour of isothermally annealed Fe-2 1/4Cr-1Mo steel in sodium. (author)

  10. Effects of sodium environment on the mechanical properties of Fe-2 1/4Cr-1Mo steel

    International Nuclear Information System (INIS)

    Chopra, O.K.

    1983-09-01

    Mechanical property data on isothermally annealed, thermally aged, and sodium-exposed Fe-2 1/4Cr-1Mo steel are analyzed to evaluate the influence of the sodium environment as well as the effects of the microstructural and compositional changes that occur in the steel during long-term exposure to sodium. Correlations are developed to predict the environmental effects on tensile, creep, fatigue, and creep-fatigue properties of Fe-2 1/4Cr-1Mo steel in sodium. The results indicate that at temperatures 0 C), degradation of mechanical properties is essentially due to thermal aging. Loss of carbon from the steel reduces both the tensile and creep-rupture strength, but has little or no effect on the fatigue properties. The cyclic properties of Fe-2 1/4Cr-1Mo steel in sodium are superior to those in air. The creep-fatigue behavior in sodium is significantly different from that in an air environment. The creep-fatigue data are analyzed using the interactive damage rate equations to predict the time-dependent fatigue behavior of isothermally annealed Fe-2 1/4Cr-1Mo steel in sodium. 15 references, 7 figures, 1 table

  11. Vehicle emissions of greenhouse gases and related tracers from a tunnel study: : CO: CO2, N2O: CO2, CH4: CO2, O2: CO2 ratios, and the stable isotopes 13C and 18O in CO2 and CO

    NARCIS (Netherlands)

    Popa, Maria Elena; Vollmer, M. K.; Jordan, A.; Brand, W. A.; Pathirana, S. L.; Rothe, M.; Röckmann, T.

    2014-01-01

    Measurements of CO2, CO, N2O and CH4 mole fractions, O2/N2 ratios and the stable isotopes 13C and 18O in CO2 and CO have been performed in air samples from the Islisberg highway tunnel (Switzerland). The molar CO : CO2 ratios, with an average of (4.15 ± 0.34) ppb:ppm, are lower than reported in

  12. Investigation of thermal fatigue of chromium-molybdenum steels, used for calcining and agglomeration constructions

    International Nuclear Information System (INIS)

    Sinyavskij, D.P.; Gorkalo, A.P.

    1979-01-01

    The technique for investigating thermal fatigue of materials is described. The data on sample stress deformed state and current temperature values are taken from the local volume of the material studied. Results of investigating thermal fatigue of the 15KhMl and 20KhMl steels are presented

  13. Observation of pH Value in Electrokinetic Remediation using various electrolyte (MgSO4, KH2PO4 and Na(NO3)) for Barren Acidic Soil at Ayer Hitam, Johor, Malaysia

    Science.gov (United States)

    Norashira, J.; Zaidi, E.; Aziman, M.; Saiful Azhar, A. T.

    2016-07-01

    Barren acidic soil collected at Ayer Hitam, Johor Malaysia was recorded at pH value of 2.36 with relative humidity of 86%. This pH value is not suitable for the growth of any plants especially for the soil stabilization purposes. Gradation weathering within the range of 4 to 6 indicates an incomplete/partial weathering process. The soil grade in this range is known as a black shale mudstone. Beside, this also influences to a factor of the high surface water runoff at this particular soil species. As the acidic pH become a major problem for soil fertilizing hence an appropriate technique was implemented known as using ‘Electrokinetic Remediation’, EKR. This technique has a great potential in changing the soil pH value from acidic to less acidic and also kept maintain the pH at the saturated rate of electrochemical process. This research study presents the monitoring data of pH value due to the effect of various electrolyte consist of 0.5M of MgSO4, KH2PO4, and Na(NO3). Here, the distilled water (DW) was used as reference solution. The electric field was provided by dipping two pieces of identical rectangular aluminum foil as anode and cathode. The EKR was conducted under a constant voltage gradient of 50 V/m across the sample bulk at 0.14 m length measured between both electrodes. The data collection was conducted during the total period of 7 days surveillance. The variation of pH values at the remediation area between anode and cathode for various type of electrolyte indicates that there are a significant saturated value as it reaches 7 days of treatment. During the analysis, it is found that the highest pH value at the remediation area after 7 days treatment using Na(NO3), KH2PO4 and MgSO4 was 3.93, 3.33 and 3.39 respectively. Hence from the last stage of pH value observation, it can be conclude that the best electrolyte for barren soil treatment is Na(NO3) whereby it contribute to highest pH value and turn the soil to be less acidic.

  14. The effects of N+ implantation on the wear and friction of type 304 and 15-5 PH stainless steels

    International Nuclear Information System (INIS)

    Yost, F.G.; Picraux, S.T.; Follstaedt, D.M.; Pope, L.E.; Knapp, J.A.

    1983-01-01

    Ion implantation of N + into mechanically polished type 304 and 15-5 PH stainless steels was studied to determine its effect on dry wear and friction behavior. Implantation of 4.0 X 10 17 N + cm -2 at 50 keV yielded a depth profile with a peak concentration of about 45 at.% at a depth of 70 nm which dropped to about 10 at.% at 120 nm. Wear and friction were studied in an unlubricated pin-on-disc configuration using type 304 and 440C stainless steel pins. Both N + -implanted steels exhibited reduced wear at low loads but no significant reduction in the coefficient of friction was found. At the lowest normal load studied (12.3 gf), the average maximum wear depth of the implanted 15-5 PH stainless steel disc (about 0.1 μm) was reduced to approximately 10% of that for the corresponding unimplanted pin-on-disc pair after 1000 cycles. At normal loads of 50 gf or above (corresponding to hertzian stresses of 1160 MPa or higher) all beneficial effects were gone. Vacuum heat treatment at 923 K for 1.8 ks of an identically implanted type 304 stainless steel specimen eradicated the beneficial effects of the nitrogen implantation. The N + -implanted discs show similar reductions in wear to discs implanted with titanium and carbon, but the N + -implanted discs do not exhibit the reductions in the coefficient of friction seen with the discs implanted with titanium and carbon. (Auth.)

  15. Study of TiC+TiN Multiple Films On Type of 316L Stainless Steel

    Institute of Scientific and Technical Information of China (English)

    XUE Qi; JIN Yong; HU Dong-ping; HUANG Ben-sheng; DENG Bai-quan

    2004-01-01

    In this paper, the synthesis process of TiC+TiN multiple films on super-low-carbon stainless steels is reported.The TiC layer is coated as the first layer in the multiple film, the change of growth rate of the film on the 316L Stainless steel is not same as the one on carbides substrates, while the mole ratio of CH4 to TiCl4 (mCH4/TiCl4) is changed from 1.2to 2.0. The Ti [C, N], as a kind of inter-layer between TiC and TiN layers, is helpful to improve the adhesion between the TiC and TiN layer. The cooling rate greatly influences the quality of the adhesion between the TiC+TiN film and substrates.

  16. ac impedance, X-ray photoelectron spectroscopy and density functional theory studies of 3,5-bis(n-pyridyl)-1,2,4-oxadiazoles as efficient corrosion inhibitors for carbon steel surface in hydrochloric acid solution

    Energy Technology Data Exchange (ETDEWEB)

    Outirite, Moha; Lagrenee, Michel; Lebrini, Mounim [Unite de Catalyse et de Chimie du Solide, UMR-CNRS 8181, ENSCL, B.P. 90108, F-59652 Villeneuve d' Ascq Cedex (France); Traisnel, Michel; Jama, Charafeddine [Laboratoire des Procedes d' Elaboration des Revetements Fonctionnels, PERF UMR-CNRS 8008, ENSCL, B.P. 90108, F-59652 Villeneuve d' Ascq Cedex (France); Vezin, Herve [Laboratoire de Chimie Organique et Macromoleculaire, UMR-CNRS 8009, USTL Bat C4, F-59655 Villeneuve d' Ascq Cedex (France); Bentiss, Fouad, E-mail: fbentiss@enscl.f [Laboratoire de Chimie de Coordination et d' Analytique, Faculte des Sciences, Universite Chouaib Doukkali, B.P. 20, M-24000 El Jadida (Morocco)

    2010-02-01

    The corrosion inhibition properties of a new class of oxadiazole derivatives, namely 3,5-bis(n-pyridyl)-1,2,4-oxadiazoles (n-DPOX) for C38 carbon steel corrosion in 1 M HCl medium were analysed by electrochemical impedance spectroscopy (EIS). An adequate structural model of the interface was used and the values of the corresponding parameters were calculated and discussed. The experimental results showed that these compounds are excellent inhibitors for the C38 steel corrosion in acid solution and that the protection efficiency increased with increasing the inhibitors concentration. Electrochemical impedance data demonstrate that the addition of the n-DPOX derivatives in the corrosive solution decreases the charge capacitance and simultaneously increases the function of the charge/discharge of the interface, facilitating the formation of an adsorbed layer over the steel surface. Adsorption of these inhibitors on the steel surface obeys to the Langmuir adsorption isotherm. X-ray photoelectron spectroscopy (XPS) and the thermodynamic data of adsorption showed that inhibition of steel corrosion in normal hydrochloric solution by n-DPOX is due to the formation of a chemisorbed film on the steel surface. Quantum chemical calculations using the Density Functional Theory (DFT) and the Quantitative Structure Activity Relationship (QSAR) approach were performed on n-DPOX derivatives to determine the relationship between molecular structure and their inhibition efficiencies. The results of the quantum chemical calculations and experimental inhibition efficiency were subjected to correlation analysis and indicate that their inhibition effect is closely related to E{sub HOMO}, E{sub LUMO}, and dipole moment (mu).

  17. On the ways of improving mechanical properties of boiler steels subject to hydrogen effect

    International Nuclear Information System (INIS)

    Tkachev, V.I.; Litvin, A.K.; Zvezdin, Yu.I.

    1975-01-01

    The effect of oxygen on the strength properties of boiler steels Kh15M2 and 48TS subjected to heat treatment and preliminary plastic deformation has been studied. It is shown that changes in the strength properties of the steel are determined by the heterogeneity of its structure. Treatment which contributes to homogenization of the metal structure increases the resistance of the steel to detrimental effect of hydrogen. Absorption of hydrogen during cathode polarization at various current densities is shown

  18. Effect of smelting method on the austenite grain size and properties of heat-resisting pearlitic steel

    International Nuclear Information System (INIS)

    Balakhovskaya, M.B.; Khusainova, N.A.; Davlyatova, L.N.

    1975-01-01

    Influence of smelting method on austenite grain size and properties of refractory perlite steel were studied. An opportunity was found to increase the steel refractoriness without deteriorating its other properties. The steel 12Kh1MF of electric or common open-hearth smelting was used. The dependence of kinetics of austenite grain growth on the smelting method was studied in the temperature range 950 deg - 1200 deg C with 1 hour exposure. The grain size of austenite in steel is supposedly determined by aluminium nitrides and vanadium carbides. In tests of normalized (kept for 20 minutes at 950-980 deg C) and tempered (kept for 3 hours at 730 deg C) transverse (tangential) pipe cross-section samples the electric steel had higher impact viscosity than the open-hearth metal. At working temperatures (540 deg -580 deg C) the difference in viscosity has its minimum. Viscosity of both steels 12Kh1MF begins to sharply decrease from 20 deg C. However, electric steel has rather high viscosity even at - 40 deg C, while the open-hearth one becomes brittle as early as at - 20 deg C. Long-term strength tests at 580 deg C under stresses 10-14 kG/mm 2 show that the coarse-grain steel is more refractory, i.e. time till fracture of open-hearth steel samples is twice as long as that of electric steel samples

  19. High-Mn steel weldment mechanical properties at 4 K

    International Nuclear Information System (INIS)

    Chan, J.W.; Sunwoo, A.J.; Morris, J.W. Jr.

    1988-06-01

    Advanced high-field superconducting magnets of the next generation of magnetic confinement fusion devices will require structural alloys with high yield strength and high toughness at cryogenic temperatures. Commercially available alloys used in the current generation of magnets, such as 300 series stainless steels, do not have the required properties. N-strengthened, high-Mn alloys meet base plate requirements in the as-rolled condition. However, the property changes associated with weld microstructural and chemical changes in these alloys have not been well characterized. In this work welding induced cryogenic mechanical property changes of an 18Mn-16Cr-5Ni-0.2N alloy are correlated with as-solidified weld microstructures and chemistries. 30 refs., 12 figs., 3 tabs

  20. On superplasticity of corrosion resistant ferritic-austenitic chromium-nickel steels

    Energy Technology Data Exchange (ETDEWEB)

    Surovtsev, A P; Sukhanov, V E

    1988-01-01

    The deformability of corrosion resistant chromium-nickel ferritic austenitic steel type O8Kh22N6T under tension, upsetting and torsion in the 600-1200 deg C temperature range is studied. For the deformation rate of the order of 10/sup -3/ s/sup -1/ the effect of superelasticity reveals itself at 850 deg C in the process of ferrite dynamic polymerization, in the 925-950 deg C range, at initial stages of dynamic recrystallization - the dynamic polygonization controlled by chromium carbide dissolving in steel and maximum at 1050 deg C in the process of development of austenite dynamic recrystallization with grain refinement with F/A ratio equalling 1. After upsetting in the elasticity mode at 1050 deg C the impact strength of the above steel is maximum.

  1. Peculiar features of determination of plastic properties in bimetals

    International Nuclear Information System (INIS)

    Voronin, A.V.; Zhadan, V.T.; Osadchij, V.A.; Rumyantsev, A.V.

    1993-01-01

    Method for calculating relative elongation of sheet bimetal on the basis of data of plastic characteristics of bimetal components has been developed. Results of calculation according to suggested method differ slightly from experimental values. It was shown analytically and supported by experiments (taking St3+12Kh18N10T samples, 45+Kh12 steel as examples), that the value of bimetal area reduction coincides with the value of area reduction of less plastic component

  2. catena-Poly[[[dichloridozinc(II]-μ-1,4-bis(1H-benzimidazol-2-yl-κN3butane] 1,4-bis(1H-benzimidazol-2-ylbutane solvate

    Directory of Open Access Journals (Sweden)

    Yan-Ling Zhou

    2010-01-01

    Full Text Available In the crystal structure of the title coordination polymer/co-crystal, {[ZnCl2(C18H18N4]·C18H18N4}n, the tetrahedrally coordinated ZnII ions are linked by the N-heterocycle into a linear chain. Another N-heterocycle present is not coordinated to the metal atom but interacts with the chain through N—H...N and N—H...Cl hydrogen bonds. The butyl chain of the uncoordinated ligand is disordered over three positions in a 0.511 (4:0.289 (5:0.200 (5 ratio.

  3. Poststroke Rehabilitation and Restorative Care Utilization: A Comparison Between VA Community Living Centers and VA-contracted Community Nursing Homes.

    Science.gov (United States)

    Jia, Huanguang; Pei, Qinglin; Sullivan, Charles T; Cowper Ripley, Diane C; Wu, Samuel S; Bates, Barbara E; Vogel, W Bruce; Bidelspach, Douglas E; Wang, Xinping; Hoffman, Nannette

    2016-03-01

    Effective poststroke rehabilitation care can speed patient recovery and minimize patient functional disabilities. Veterans affairs (VA) community living centers (CLCs) and VA-contracted community nursing homes (CNHs) are the 2 major sources of institutional long-term care for Veterans with stroke receiving care under VA auspices. This study compares rehabilitation therapy and restorative nursing care among Veterans residing in VA CLCs versus those Veterans in VA-contracted CNHs. Retrospective observational. All Veterans diagnosed with stroke, newly admitted to the CLCs or CNHs during the study period who completed at least 2 Minimum Data Set assessments postadmission. The outcomes were numbers of days for rehabilitation therapy and restorative nursing care received by the Veterans during their stays in CLCs or CNHs as documented in the Minimum Data Set databases. For rehabilitation therapy, the CLC Veterans had lower user rates (75.2% vs. 76.4%, P=0.078) and fewer observed therapy days (4.9 vs. 6.4, Pcare, CLC Veterans had higher user rates (33.5% vs. 30.6%, Pcare days (9.4 vs. 5.9, Pcare (coefficient=5.48±0.37, Pcare both before and after risk adjustment.

  4. Photochemically activated antiviral halogenated 1,8-naphthalimides: synthesis of N,N'-bis-{2-[(5-bromo-2-[1-14C]hexyl-1H-benz[de]isoquinolin-1,3(2H)-dion-6-yl)amino]ethyl}hexanediamide

    International Nuclear Information System (INIS)

    Hayes, B.A.; Gupta, Surendra; Shaochieh Chang; Utecht, R.E.; Lewis, D.E.

    1996-01-01

    The synthesis of N,N'-bis-{2-[(5-bromo-2-[1- 14 C]hexyl-1H-benz[de]isoquinolin-1, 3(2H)-dion-6-yl)amino]ethyl}hexanediamide from 1-[1- 14 C]-hexylamine and 4-chloro-1,8-naphthalic anhydride is described. The anhydride is first converted to the 4-chloro-n-[1- 14 C]hexyl-1,8-naphthalimide by condensation with 1-[1- 14 C]-hexylamine, and the chlorine is then displaced with ethylenediamine to give the 4-(2-aminoethylamino-N-[1- 14 C]hexyl-1,8-naphthalimide. Coupling of this monomeric naphthalimide with adipoyl chloride affords the dimeric naphthalimide which is brominated regiospecifically with elemental bromine in carbon tetrachloride to afford the title compound. (author)

  5. Effect of laser absorption on picosecond laser ablation of Cr12MoV mold steel, 9Cr18 stainless steel and H13A cemented carbide

    Science.gov (United States)

    Wu, Baoye; Liu, Peng; Wang, Xizhao; Zhang, Fei; Deng, Leimin; Duan, Jun; Zeng, Xiaoyan

    2018-05-01

    Due to excellent properties, Cr12MoV mold steel, 9Cr18 stainless steel and H13A cemented carbide are widely used in industry. In this paper, the effect of absorption of laser light on ablation efficiency and roughness have been studied using a picosecond pulse Nd:YVO4 laser. The experimental results reveal that laser wavelength, original surface roughness and chemical composition play an important role in controlling ablation efficiency and roughness. Firstly, higher ablation efficiency with lower surface roughness is achieved on the ablation of 9Cr18 at 532, comparing with 1064 nm. Secondly, the ablation efficiency increases while the Ra of the ablated region decreases with the decrease of original surface roughness on ablation of Cr12MoV mold steel at 532 nm. Thirdly, the ablation efficiency of H13A cemented carbide is much higher than 9Cr18 stainless steel and Cr12MoV mold steel at 1064 nm. Scanning electron microscopy images reveals the formation of pores on the surface of 9Cr18 stainless steel and Cr12MoV mold steel at 532 nm while no pores are formed at 1064 nm. As to H13A cemented carbide, worm-like structure is formed at 1064 nm. The synergetic effects of the heat accumulation, plasma shielding and ablation threshold on laser ablation efficiency and machining quality were analyzed and discussed systematically in this paper.

  6. Tribological properties of CrN coatings deposited by nitro-chromizing treatment on AISI D2 steel

    Energy Technology Data Exchange (ETDEWEB)

    Durmaz, M., E-mail: mdurmaz@sakarya.edu.tr; Abakay, E.; Sen, U.; Sen, S. [Department of Metallurgical and Materials Engineering, Engineering Faculty, Sakarya University, Esentepe Campus, 54187 Sakarya (Turkey); Kilinc, B. [Department of Metallurgical and Materials Engineering, Institute of Arts and Sciences, Sakarya University, Esentepe Campus, 54187 Sakarya (Turkey)

    2015-03-30

    In this work, the wear test of uncoated and chromium nitride coated AISI D2 cold work tool steel against alumina ball realized at 0.1 m/s sliding speeds and under the loads of 2.5N, 5N and 10N. Steel samples were nitrided at 575°C for 8 h in the first step of the coating process, and then chromium nitride coating was performed thermo-reactive deposition technique (TRD) in a powder mixture consisting of ferro-chromium, ammonium chloride and alumina at 1000°C for 2 h. Nitro-chromized samples were characterized by X-Ray diffraction analysis (XRD), scanning electron microscopy (SEM), micro-hardness and ball on disk wear tests. The coating layer formed on the AISI D2 steel was compact and homogeneous. X-ray studies showed that the phase formed in the coated layer is Cr{sub 2}N. The depth of the layer was 8.15 µm. The average hardness of the layer was 2160±15 HV{sub 0.025}. For uncoated and chromium nitride materials, wear rate increased with increasing load. The results of friction coefficient and wear rate of the tested materials showed that the CrN coating presents the lowest results.

  7. Tribological properties of CrN coatings deposited by nitro-chromizing treatment on AISI D2 steel

    International Nuclear Information System (INIS)

    Durmaz, M.; Abakay, E.; Sen, U.; Sen, S.; Kilinc, B.

    2015-01-01

    In this work, the wear test of uncoated and chromium nitride coated AISI D2 cold work tool steel against alumina ball realized at 0.1 m/s sliding speeds and under the loads of 2.5N, 5N and 10N. Steel samples were nitrided at 575°C for 8 h in the first step of the coating process, and then chromium nitride coating was performed thermo-reactive deposition technique (TRD) in a powder mixture consisting of ferro-chromium, ammonium chloride and alumina at 1000°C for 2 h. Nitro-chromized samples were characterized by X-Ray diffraction analysis (XRD), scanning electron microscopy (SEM), micro-hardness and ball on disk wear tests. The coating layer formed on the AISI D2 steel was compact and homogeneous. X-ray studies showed that the phase formed in the coated layer is Cr 2 N. The depth of the layer was 8.15 µm. The average hardness of the layer was 2160±15 HV 0.025 . For uncoated and chromium nitride materials, wear rate increased with increasing load. The results of friction coefficient and wear rate of the tested materials showed that the CrN coating presents the lowest results

  8. Tribological properties of CrN coatings deposited by nitro-chromizing treatment on AISI D2 steel

    Science.gov (United States)

    Durmaz, M.; Kilinc, B.; Abakay, E.; Sen, U.; Sen, S.

    2015-03-01

    In this work, the wear test of uncoated and chromium nitride coated AISI D2 cold work tool steel against alumina ball realized at 0.1 m/s sliding speeds and under the loads of 2.5N, 5N and 10N. Steel samples were nitrided at 575°C for 8 h in the first step of the coating process, and then chromium nitride coating was performed thermo-reactive deposition technique (TRD) in a powder mixture consisting of ferro-chromium, ammonium chloride and alumina at 1000°C for 2 h. Nitro-chromized samples were characterized by X-Ray diffraction analysis (XRD), scanning electron microscopy (SEM), micro-hardness and ball on disk wear tests. The coating layer formed on the AISI D2 steel was compact and homogeneous. X-ray studies showed that the phase formed in the coated layer is Cr2N. The depth of the layer was 8.15 µm. The average hardness of the layer was 2160±15 HV0.025. For uncoated and chromium nitride materials, wear rate increased with increasing load. The results of friction coefficient and wear rate of the tested materials showed that the CrN coating presents the lowest results.

  9. Comparative estimation of weld-ability of medium-alloy steels

    International Nuclear Information System (INIS)

    Makarov, Eh.L.; Laz'ko, V.E.

    1977-01-01

    Weldability of various industrial steels has been investigated as affected by mutual presence of carbon and alloying elements in a wide range of concentrations. Mechanical properties and technological strength of medium alloyed steel welded joints have been compared. Technological strength parameters have been found to sharply decrease with increasing carbon content, the decrease depending on the alloying system. Resistance to hot and cold cracking is somewhat decreased by nickel and increased by molibdenum and tungsten. The best mechanical properties are displayed by steels of the Kh2GSNVM type. Industrial evidence on argon arc welding of different constructions made of steels 1.5-20 mm thick is compared to laboratory results. Accordingly, the high strength steels are divided into three groups, i.e. those manifesting good, satisfactory and poor weldability

  10. Hot ductility of structural steels melted with the use of direct reduction charge

    International Nuclear Information System (INIS)

    Marchenko, V.N.; Bulat, S.I.; Litvinenko, D.A.

    1982-01-01

    A possibility of the use of direct reduction charge during the open arc melting of the 40Kh2N2MA steel with the subsequent electroslag remelting was investigated. It is shown that the use of such charge free from non-ferrous metal admixtures permits to increase an alloy hot ductility in the hot-brittleness range from 900 up to 1500 deg C. An increase of the deformation rate from 0.1 up to 1 s - 1 increases 1.5-3 times a level of minimum ductility within this temperature range. It is established that antimony and bismuth impurities considerably decrease hot ductility

  11. Investigation of fretting corrosion of vacuum-chrome-plated vt3-1 titanium alloy in pair with unprotected vt3-1 alloy and 40khnma steel

    International Nuclear Information System (INIS)

    Rojkh, I.L.; Koltunova, L.N.; Vejtsman, M.G.; Birman, Ya.N.; Skosarev, A.V.; Kogan, I.S.

    1978-01-01

    The character of destruction of contacting surfaces in the process of fretting corrosion of titanium alloy VT3-1 chromized in vacuum in pair with unprotected alloy VT3-1 and steel 40KhNMA has been studied by scanning electron microscopy, electronography, and recording the surface profile. The specific load was 200 kg/cm 2 , vibration amplitude 50 mkm and frequency 500 Hz. It has been established that pairs unprotected with coating are subjected to intensive fretting corrosion especially when they are made of titanium alloy. For the pair chromized alloy VT3-1 - unprotected alloy VT3-1 no destruction of a chromized surface is observed. Vacuum chromium coating in the pair with steel 40KhNMA reveals similar properties as in pair with a titanium alloy. The surface of a steel sample is destroyed because of fretting corrosion, though the intensity of corrosion is lower than in the case of unprotected pairs. Vacuum chromium coating is recommended for protection of titanium alloy VT3-1 from fretting corrosion in pair with steel 40KhNMA or an alloy VT3-1 especially in those cases when various organic coatings are unsuitable

  12. Corrosion of stainless steel in alcohol solutions of the simplest carboxylic acids

    International Nuclear Information System (INIS)

    Vigdorovich, V.I.; Korneeva, T.V.; Tsygankova, L.E.

    1975-01-01

    The behaviour of stainless Kh18N10T steel is considered in the methanol and ethanol solutions of formic and acetic acids, respectively. Consideration is given to the effect of the concentration (C) of the acid (0.01-1.00 N), water (0.1-20.0 mass.%) and temperature (room temperature, 40 and 60 deg C). Curves of anodic polarization were plotted. In the course of time in 1.0 and 0.5 N anhydrous methanol solutions of HCOOH at room temperature in the absence of the external anode current one can observe an increase in the electrode potential. Continued reduction of the formic acid concentration results in an improvement on the initial potential (psi) and a practical constancy of psi in time. It is shown that depending on the acid concentration the additions of water are capable of producing both a passivating and an activating effect. It is assumed that the growth in the length of the hydrocarbon radical of carboxylic acid promotes the adsorption displacement of water and alcohols from the metal surface and enhancement of the corrosion rate

  13. Effect of reactor irradiation on long-term strength and creep of 0Kh16N15M3B steel under plane stressed state

    International Nuclear Information System (INIS)

    Khristov, G.P.; Kosov, B.D.

    1982-01-01

    The paper deals with analysis of results of experimental studies in creep of the austenitic OKh16n15m3b steel with various size of initial-structure grain under conditions of high-intensity reactor irradiation and control tests. It is suggested to consider the material initial structure effect on intensity of minimum creep rates both under ordinary and intrareactor conditions of loading by means of the function grain size effect on the equivalent stress. It is shown that the criterial expression previously suggested by the authors is invariant to the type of stressed and structural states and relative to intensity of minimal creep rates. It is established that the creep rate of the irradiated steel may be calculated from dependence for nonirradiated steel using as an argument a certain reduced equivalent stress which is a function of the acting stress and irradiation parameter

  14. N = 4 super KdV hierarchy in N = 4 and N = 2 superspaces

    International Nuclear Information System (INIS)

    Delduc, F.

    1995-10-01

    The results of further analysis of the integrability properties of the N = 4 supersymmetric KdV equation deduced earlier as a Hamiltonian flow on N 4 SU(2) superconformal algebra in the harmonic N = 4 superspace are presented. To make this equation and the relevant Hamiltonian structures more tractable, it is reformulated in the ordinary N = 4 and further in N = 2 superspaces. These results provide a strong evidence that the unique N = 4 SU(2) super KdV hierarchy exists. (author)

  15. Radiolabelling of isopeptide N{sup {epsilon}}-({gamma}-glutamyl)-L-lysine by conjugation with N-succinimidyl-4-[{sup 18}F]fluorobenzoate

    Energy Technology Data Exchange (ETDEWEB)

    Wuest, F; Hultsch, C; Bergmann, R; Johannsen, B; Henle, T

    2003-07-01

    The isopeptide N{sup {epsilon}}-({gamma}-glutamyl)-L-lysine 4 was labelled with {sup 18}F via N-succinimidyl-4-[{sup 18}F]fluorobenzoate ([{sup 18}F]SFB). A modified approach for the convenient synthesis of [{sup 18}F]SFB was used, and [{sup 18}F]SFB could be obtained in decay-corrected radiochemical yields of 44-53% (n=20) and radiochemical purity >95% within 40 min after EOB. For labelling N{sup {epsilon}}-({gamma}-glutamyl)-L-lysine with [{sup 18}F]SFB the effects of isopeptide concentration, temperature, and pH were studied to determine the optimum reaction conditions. The coupling reaction was shown to be temperature and pH independent while being strongly affected by the isopeptide concentration. Using the optimized labelling conditions, in a typical experiment 1.3 GBq of [{sup 18}F]SFB could be converted into 447 MBq (46%, decay-corrected) of [{sup 18}F]fluorobenzoylated isopeptide within 45 min, including HPLC purification.

  16. Corrosion Inhibition and Adsorption Characteristics of Tarivid on Mild Steel in H2SO4

    Directory of Open Access Journals (Sweden)

    N. O. Eddy

    2010-01-01

    Full Text Available The corrosion inhibition and adsorption characteristics of (+/--9-fluoro-2,3-dihydro-3-methyl-10-(4-methyl-1-piperazinyl-7-oxo-7H-pyrido[1,2,3-de]-1,4-benzoxazine-6-carboxylic acid (Tarivid on the corrosion of mild steel has been studied using thermometric and gasometric methods. The study reveals that tarivid inhibits the corrosion of mild steel in H2SO4. The values of inhibition efficiency of tarivid were found to increase as its concentration increased but decreased with increase in temperature. Activation energies of the inhibited corrosion of mild steel ranged from 39.05 to 50.61 kJ/mol. Values of enthalpy change and free energy of adsorption were negative which indicated exothermic and spontaneous adsorption process. Physical adsorption mechanism is proposed from the obtained kinetic and thermodynamic parameters. Langmuir adsorption isotherm model is obeyed from the fit of the experimental data.

  17. Crystal structure of (4,4′-bipyridyl-κNbis[N-(2-hydroxyethyl-N-isopropyldithiocarbamato-κ2S,S′]zinc(II–4,4′-bipyridyl (2/1 and its isostructural cadmium(II analogue

    Directory of Open Access Journals (Sweden)

    Yee Seng Tan

    2017-11-01

    Full Text Available The title structures, [M(C6H12NOS22(C10H8N2]·0.5C10H8N2, for M = Zn, (I, and Cd, (II, feature terminally bound 4,4′-bipyridyl ligands and non-coordinating 4,4′-bipyridyl molecules, with the latter disposed about a centre of inversion. The coordination geometry about the metal atom is defined by two non-symmetrically chelating dithiocarbamate ligands and a pyridyl N atom. The NS4 donor sets are distorted but, approximate to trigonal bipyramidal in each case. In the crystal, hydroxy-O—H...O(hydroxy and hydroxy-O—H...N(pyridyl hydrogen bonds between the zinc-containing molecules lead to a supramolecular layer parallel to (100. The three-dimensional architecture arises as the layers are linked via methine-C—H...S, pyridyl-C—H...O(hydroxy and π–π [inter-centroid distance between coordinated pyridyl rings = 3.6246 (18 Å] interactions. Channels along the c-axis direction are occupied by the non-coordinating 4,4′-bipyridine molecules, which are held in place by C—H...π(chelate ring contacts.

  18. Kankaan tuotekehittäminen erikoisolosuhteisiin K&H Annala Oy:lle

    OpenAIRE

    Koski, Marjo

    2017-01-01

    Opinnäytetyö tehtiin yhteistyössä Suomen ainoan huonekalukankaita valmistavan yrityksen K&H Annala Oy:n kanssa. Työn aiheena oli suunnitella ja tuotteistaa kangasmallisto erikoisolosuhteisiin innovatiivisesta, Italiassa valmistettavasta Flyer-langasta. Projektin lähtökohtana oli opinnäytetyöntekijän kasvava kiinnostuneisuus kudottuja tekstiilejä kohtaan ja kankaan suunnitteluprosessin vieminen teollisen tuotannon puolelle. Projektissa tähdättiin uudentyyppiseen kankaaseen ilmeen ja materiaali...

  19. Study on the process of calibration and deep centring of blanks

    International Nuclear Information System (INIS)

    Potapov, I.N.; Romantsev, B.A.; Popov, V.A.; Volodin, V.V.; Goncharuk, A.V.

    1985-01-01

    Process of calibration and deep centring of blanks before broaching is developed and studied. Investigations are performed at a semi-industrial screw rolling mill MISiS-100 T. Blanks made of 40Kh, 60, 50, 45KhN2MFA, 30KhGSNA steels 80, 85, and 90 mm in diameter and 300 mm long were calibrated and centered after heating in a furnace to a depth of 200 mm at shafts and faces with different calibration. 30KhN2MFA steel is chosen for face material; heat treatment is conducted under the following conditions: heating up to 950-1000 deg C and hold-up during 30-35 min with the following cooling in the air. The above experimental investigations reveal that the process of calibration and deep centring accomplished at a three-shaft screw rolling mill is rather stable and provides a high accuracy of centering hollow marking

  20. Manufacture of tube billets for fuel cans by vacuum centrifugal casting

    International Nuclear Information System (INIS)

    Zelenskij, V.F.; Neklyudov, I.M.; Chernyj, B.P.

    1989-01-01

    Vacuum device for induction melting with centrifugal casting in the ingot mold with rotation vertical or horisontal axis is presented. Removing and grinding of nonmetallic inclusions are realized by selection of casting conditions and of chemically active reducer, sound metal with high ductility is obtained. Data on micro- and macrostructure of casted tube billets made of 08Kh18N10T and 06Kh16H15M3B stainless steels, designed for manufacture of fuel cans are presented

  1. Radiosynthesis of dimethyl-2-[{sup 18}F]-(fluoromethyl)-6-methyl-4-(2-nitrophenyl)-1,4-dihydropyridine-3,5-dicarboxylate for L-type calcium channel imaging

    Energy Technology Data Exchange (ETDEWEB)

    Sadeghpour, H. [Nuclear Medicine Research Group, Agricultural, Medical and Industrial Research School (AMIRS), Karaj (Iran); Faculty of Pharmacy and Pharmaceutical Sciences Research Center, Tehran Univ. of Medical Sciences, Tehran (Iran); Jalilian, A.R.; Akhlaghi, M.; Mirzaei, M. [Nuclear Medicine Research Group, Agricultural, Medical and Industrial Research School (AMIRS), Karaj (Iran); Shafiee, A. [Faculty of Pharmacy and Pharmaceutical Sciences Research Center, Tehran Univ. of Medical Sciences, Tehran (Iran); Miri, R. [Medicinal and Natural Products Chemistry Research Center, Shiraz Univ. of Medical Sciences, Shiraz (Iran)

    2008-07-01

    Dimethyl 2-(fluoromethyl)-6-methyl-4-(2-nitrophenyl)-1,4-dihydropyridine-3,5-dicarboxylate 4a, a fluorinated nifedipine analog, has been shown to elicit significant calcium channel blocker activity using a guinea pig ileal longitudinal smooth muscle model. In order to perform biological studies for detection of L-type calcium channel distribution, we decided to prepare the [{sup 18}F]-labeled compound. The latter compound was prepared in no-carrier-added (n.c.a.) form from dimethyl 2-(bromomethyl)-6-methyl-4-(2-nitrophenyl)-1,4-dihydropyridine-3,5-dicarboxylate 2 in one step at 80 C in Kryptofix[222]/K[{sup 18}F]F and acetonitrile as a solvent in 15 min. Column chromatography afforded the radiochemically pure compound in 20 min. Radiochemical purity of the {sup 18}F-nifedipine was determined by RTLC and HPLC (> 98%) and specific activity of 21-48 GBq/{mu}mol (EOB). (orig.)

  2. A simplified one-pot synthesis of 9-[(3-[18F]Fluoro-1-hydroxy-2-propoxy)methyl]guanine([18F]FHPG) and 9-(4-[18F]Fluoro-3-hydroxymethylbutyl)guanine ([18F]FHBG) for gene therapy

    International Nuclear Information System (INIS)

    Shiue, Grace G.; Shiue, Chyng-Yann; Lee, Roland L.; MacDonald, Douglas; Hustinx, Roland; Eck, Stephen L.; Alavi, Abass A.

    2001-01-01

    9-[(3-[ 18 F]Fluoro-1-hydroxy-2-propoxy)methyl]guanine ([ 18 F]FHPG, 2) has been synthesized by nucleophilic substitution of N 2 -(p-anisyldiphenylmethyl)-9-{[1-(p-anisyldiphenylmethoxy)-3 -toluenesulfonyloxy-2-propoxy]methyl}guanine (1) with potassium [ 18 F]fluoride/Kryptofix 2.2.2 followed by deprotection with 1 N HCl and purification with different methods in variable yields. When both the nucleophilic substitution and deprotection were carried out at 90 deg. C and the product was purified by HPLC (method A), the yield of compound 2 was 5-10% and the synthesis time was 90 min from EOB. However, if both the nucleophilic substitution and deprotection were carried out at 120 deg. C and the product was purified by HPLC, the yield of compound 2 decreased to 2%. When compound 2 was synthesized at 90 deg. C and purified by Silica Sep-Pak (method B), the yield increased to 10-15% and the synthesis time was 60 min from EOB. Similarly, 9-(4-[ 18 F]fluoro-3-hydroxymethylbutyl)guanine ([ 18 F]FHBG, 4) was synthesized with method A and method B in 9% and 10-15% yield, respectively, in a synthesis time of 90 and 60 min, respectively, from EOB. Compound 2 was relatively unstable in acidic medium at 120 deg. C while compound 4 was stable under the same condition. Both compound 2 and compound 4 had low lipid/water partition coefficient (0.126±0.022, n=5 and 0.165±0.023, n=5, respectively). Although it contains non-radioactive ganciclovir (∼5-30 μg) as a chemical by-product, compound 2 synthesized by method B has a similar uptake in 9L glioma cells as that synthesized by method A, and is a potential tracer for imaging herpes simplex virus thymidine kinase gene expression in tumors using PET. Similarly, compound 4 synthesized by method B contains ∼10-25 μg of penciclovir as a chemical by-product. Thus, the simplified one pot synthesis (method B) is a useful method for synthesizing both compound 2 and compound 4 in good yield for routine clinical use, and the method is

  3. Ductile fracture of two-phase welds under 77K

    International Nuclear Information System (INIS)

    Yushchenko, K.A.; Voronin, S.A.; Pustovit, A.I.; Shavel', A.V.

    1984-01-01

    The effect of the type of welding and fillers on crack resistance of welded joints high-strength steel EhP810 and its various compounds with steels EhP666, 08Kh18N10T has been studied. For the welding of steel EhP810 with steels EhP810, EhP666, 08Kh18N10T electron-beam, automatic, argon tungsten arc with non-consumable electrode with various fillers, as well as argon metal-arc welding with consumable electrode, were used. It is shown, that for a joint, made by electron-beam welding, parameters σsub(u), Ksub(IcJ), KCV are higher than for a joint of a similar phase structure made using filler wire EhP659-VI. It is explained by the fact, that during electron-beam welding joint metal refining takes place, which removes gases. In welded joints of chP810 steel, having joints with austenitic structure, characteristic of crack resistance Ssub(c) increases by more than 0.2 mm in contrast to two-phase joints, which conventional yield strength at 77 K exceeds 1000 MPa. It is worth mentioning, that for other classes of steels formation of two-phase structure of joint increases welded joint resistance to brittle fracture. It is possible to obtain the required structure of joint with assigned level of resistance to brittle fracture by means of the use of different fillers, optimum and welding procedure, regulaing the part of the basic metal in joint content

  4. Threshold oxygen levels in Na(I) for the formation of NaCrO 2(s) on 18-8 stainless steels from accurate thermodynamic measurements

    Science.gov (United States)

    Sreedharan, O. M.; Madan, B. S.; Gnanamoorthy, J. B.

    1983-12-01

    The compound NaCrO 2(s) is an important corrosion product in sodium-cooled LMFBRs. The standard Gibbs energy of formation of NaCrO 2(s) is required for the computation of threshold oxygen levels in Na(1) for the formation of NaCrO 2(s) on 18-8 stainless steels. For this purpose the emf of the galvanic cell: Pt, NaCrO 2, Cr 2O 3, Na 2CrO 4/15 YSZ/O 2 ( P O 2 = 0.21 atm, air), Pt was measured over 784-1012 K to be: (E±4.4)(mV) = 483.67-0.34155 T(K). From this, the standard Gibbs energy of formation of NaCrO 2(s) from the elements ( ΔG f,T0) and from the oxides ( ΔG f,OX,T0) was calculated to be: [ΔG f,T0(NaCrO 2, s)±1.86] (kJ/mol) =-869.98 + 0.18575 T(K) , [ΔG f,OX,T0(NaCr0 2, s)±4.8] (kJ/mol) = -104.25-0.00856 T(K) . The molar heat capacity, C P0, of NaCrO 2(s) was measured by DSC to be (350-600 K): C P0(NaCrO 2, s) (J/K mol) = 27.15 + 0.1247 T (K) , From these data, values of -99.3 kJ/mol and 91.6 J/K mol were computed for ΔH f,2980 and S 2980 of NaCrO 2(s). The internal consistency was checked with the use of enthalpy data on Na 2CrO 4(s). From the standard Gibbs energy of formation of NaCrO 2(s) the equation logC 0(wppm) = 3.9905-3147.6 T(K) was derived, where C 0 is the threshold oxygen level for the formation of NaCrO 2(s) on 18-8 stainless steels.

  5. Effect of smelting method on the austenite grain size and properties of heat-resisting pearlitic steel

    Energy Technology Data Exchange (ETDEWEB)

    Balakhovskaya, M B; Khusainova, N A; Davlyatova, L N [Vsesoyuznyj Nauchno-Issledovatel' skij Teplotekhnicheskij Inst., Moscow (USSR)

    1975-12-01

    Influence of smelting method on austenite grain size and properties of refractory perlite steel were studied. An opportunity was found to increase the steel refractoriness without deteriorating its other properties. The steel 12Kh1MF of electric or common open-hearth smelting was used. The dependence of kinetics of austenite grain growth on the smelting method was studied in the temperature range 950 deg - 1200 deg C with 1 hour exposure. The grain size of austenite in steel is supposedly determined by aluminium nitrides and vanadium carbides. In tests of normalized (kept for 20 minutes at 950-980 deg C) and tempered (kept for 3 hours at 730 deg C) transverse (tangential) pipe cross-section samples the electric steel had higher impact viscosity than the open-hearth metal. At working temperatures (540 deg -580 deg C) the difference in viscosity has its minimum. Viscosity of both steels 12Kh1MF begins to sharply decrease from 20 deg C. However, electric steel has rather high viscosity even at /sup -/40 deg C, while the open-hearth one becomes brittle as early as at /sup -/20 deg C. Long-term strength tests at 580 deg C under stresses 10-14 kG/mm/sup 2/ show that the coarse-grain steel is more refractory, i.e. time till fracture of open-hearth steel samples is twice as long as that of electric steel samples.

  6. Diaqua{6,6′-dimethoxy-2,2′-[ethane-1,2-diylbis(nitrilomethylidyne]diphenolato-κ2O,N,N′,O′}manganese(III perchlorate 18-crown-6 hemisolvate monohydrate

    Directory of Open Access Journals (Sweden)

    Ming-Ming Yu

    2009-02-01

    Full Text Available In the cation of the title compound, [Mn(C18H18N2O4(H2O2]ClO4·0.5C12H24O6·H2O, the MnIII ion is coordinated by two water O atoms, and two O atoms and two N atoms from the tetradentate 6,6′-dimethoxy-2,2′-[ethane-1,2-diylbis(nitrilomethylidyne]diphenolate ligand, completing a distorted octahedral geometry. One O atom of the 18-crown-6-ether is disordered over two positions with occupancies of 0.70 (2 and 0.30 (2.

  7. Interactions between 4-(2-dimethylaminoethyloxy)-N-octadecyl-1,8-naphthalimide and serum albumins: Investigation by spectroscopic approach

    Energy Technology Data Exchange (ETDEWEB)

    Sun Yang; Wei Song [School of Chemical Engineering, Northwest University, No. 229 Taibai North Road, Xi' an, Shaanxi 710069 (China); Zhao Yingyong [Biomedicine Key Laboratory of Shaanxi Province, Northwest University, No. 229 Taibai North Road, Xi' an, Shaanxi 710069 (China); Hu Xiaoyun, E-mail: hxy3275@nwu.edu.cn [Department of Physics, Northwest University, No. 229 Taibai North Road, Xi' an, Shaanxi 710069 (China); Fan Jun, E-mail: fanjun@nwu.edu.cn [School of Chemical Engineering, Northwest University, No. 229 Taibai North Road, Xi' an, Shaanxi 710069 (China)

    2012-04-15

    A novel 4-(2-dimethylaminoethyloxy)-N-octadecyl-1,8-naphthalimide (DON) has been synthesized as a spectrofluorimetric probe for the determination of proteins. Photophysics of DON in different solvents has been delineated in this paper. Progressive redshift with polarity of solvents in emission and absorption spectra hints at intramolecular charge transfer. The interactions of DON with serum albumins (i.e., human serum albumin (HSA) and bovine serum albumin (BSA)) were studied by fluorescence and absorption spectroscopy. Fluorescence data revealed that the quenching of HSA/BSA by DON were static quenching and the DON-HSA/BSA complexes were formed. The binding constant (K{sub b}) for HSA and was found to be 8.44 Multiplication-Sign 10{sup -4} and 60.26 Multiplication-Sign 10{sup -4} M{sup -1} and the number of binding sites (n) were 1.00 and 1.40, respectively. The thermodynamic parameters, {Delta}H and {Delta}S, for the DON-HSA system was calculated to be -14.83 kJ mol{sup -1} and 23.61 J mol{sup -1} K{sup -1}, indicating the hydrogen bonds and hydrophobic interactions were the dominant intermolecular force. {Delta}H and {Delta}S for the binding of DON with BSA was -60.08 kJ mol{sup -1} and -90.7441 mol{sup -1} K{sup -1}, suggesting the hydrogen bonds and van der Waals force played the main role in the interaction. The results of displacement experiments showed that DON bound HSA/BSA occurred at the Trp-214 proximity, located in subdomain IIA of the serum albumin structure (the warfarin binding pocket). The effect of DON on the conformation of HSA was also analyzed by synchronous and three-dimensional fluorescence spectra. The fluorescence of DON could be quenched by HSA, based on which, a fluorometric method for the determination of microamount protein using DON in the medium of HCl-Tris buffer solution (pH=7.4) was developed. The linear range of the calibration curves was 0.1-10.0 {mu}M for HSA, 0.1-11.2 {mu}M for BSA and 0.2-9.7 {mu}M for egg albumin (EA). The

  8. Interactions between 4-(2-dimethylaminoethyloxy)-N-octadecyl-1,8-naphthalimide and serum albumins: Investigation by spectroscopic approach

    International Nuclear Information System (INIS)

    Sun Yang; Wei Song; Zhao Yingyong; Hu Xiaoyun; Fan Jun

    2012-01-01

    A novel 4-(2-dimethylaminoethyloxy)-N-octadecyl-1,8-naphthalimide (DON) has been synthesized as a spectrofluorimetric probe for the determination of proteins. Photophysics of DON in different solvents has been delineated in this paper. Progressive redshift with polarity of solvents in emission and absorption spectra hints at intramolecular charge transfer. The interactions of DON with serum albumins (i.e., human serum albumin (HSA) and bovine serum albumin (BSA)) were studied by fluorescence and absorption spectroscopy. Fluorescence data revealed that the quenching of HSA/BSA by DON were static quenching and the DON–HSA/BSA complexes were formed. The binding constant (K b ) for HSA and was found to be 8.44×10 −4 and 60.26×10 −4 M −1 and the number of binding sites (n) were 1.00 and 1.40, respectively. The thermodynamic parameters, ΔH and ΔS, for the DON–HSA system was calculated to be −14.83 kJ mol −1 and 23.61 J mol −1 K −1 , indicating the hydrogen bonds and hydrophobic interactions were the dominant intermolecular force. ΔH and ΔS for the binding of DON with BSA was −60.08 kJ mol −1 and −90.7441 mol −1 K −1 , suggesting the hydrogen bonds and van der Waals force played the main role in the interaction. The results of displacement experiments showed that DON bound HSA/BSA occurred at the Trp-214 proximity, located in subdomain IIA of the serum albumin structure (the warfarin binding pocket). The effect of DON on the conformation of HSA was also analyzed by synchronous and three-dimensional fluorescence spectra. The fluorescence of DON could be quenched by HSA, based on which, a fluorometric method for the determination of microamount protein using DON in the medium of HCl−Tris buffer solution (pH=7.4) was developed. The linear range of the calibration curves was 0.1–10.0 μM for HSA, 0.1–11.2 μM for BSA and 0.2–9.7 μM for egg albumin (EA). The detection limit (3σ) for HSA was 1.12×10 −10 M, for BSA it was 0.92×10

  9. Nature in corrosion-erosion surface for [TiN/TiAlN]n nanometric multilayers growth on AISI 1045 steel

    Energy Technology Data Exchange (ETDEWEB)

    Caicedo, J.C., E-mail: jcaicedoangulo@gmail.com [Thin Films Group Universidad del Valle, Ciudad Universitaria Melendez, A.A. 25360, Cali (Colombia); Advanced Materials for Micro and NanoTechnology Research Group Universidad Autonoma de Occidente (Colombia); Cabrera, G. [Thin Films Group Universidad del Valle, Ciudad Universitaria Melendez, A.A. 25360, Cali (Colombia); Caicedo, H.H. [Department of Bioengineering, University of Illinois at Chicago, IL 60612 (United States); Department of Anatomy and Cell Biology, University of Illinois at Chicago, IL 60612 (United States); Amaya, C. [Thin Films Group Universidad del Valle, Ciudad Universitaria Melendez, A.A. 25360, Cali (Colombia); Hard Coating Laboratory CDT-ASTIN SENA, Cali (Colombia); Aperador, W. [Ingenieria Mecatronica, Universidad Militar Nueva Granada, Bogota (Colombia)

    2012-04-30

    The aim of this work is to characterize the electrochemical behavior of [TiN/TiAlN]n multilayer coatings under corrosion-erosion condition. The multilayers with bilayer numbers (n) of 2, 6, 12, and 24 and/or bilayer period ({Lambda}) of 1500 nm, 500 nm, 250 nm, 150 nm and 125 nm were deposited by magnetron sputtering technique on Si (100) and AISI 1045 steel substrates. Both, the TiN and the TiAlN structures for multilayer coatings were evaluated via X-ray diffraction analysis. Mechanical and tribological properties were evaluated via nanoindentation measurements and scratch test respectively. Silica particles were used as abrasive material on corrosion-erosion test in 0.5 M of H{sub 2}SO{sub 4} solution at impact angles of 30 Degree-Sign and 90 Degree-Sign over surface. The electrochemical characterization was carried out using polarization resistance technique (Tafel), in order to observe changes in corrosion rate as a function of the bilayer number (n) or the bilayer period ({Lambda}) and the impact angle. Corrosion rate values of 9115 {mu}m y for uncoated steel substrate and 2615 {mu}m y for substrate coated with n = 24 ({Lambda} = 125 nm) under an impact angle of 30 Degree-Sign were found. On the other hand, for an impact angle of 90 Degree-Sign the corrosion rate exhibited 16401 {mu}m y for uncoated steel substrate and 5331 {mu}m y for substrate coated with n = 24 ({Lambda} = 125 nm). This behavior was correlated with the curves of mass loss for both coated samples and the surface damage was analyzed via scanning electron microscopy images for the two different impact angles. These results indicate that TiN/TiAlN multilayer coatings deposited on AISI 1045 steel represent a practical solution for applications in corrosive-erosive environments. - Highlights: Black-Right-Pointing-Pointer Determination of superficial phenomenon that occurs in surface of multilayer films. Black-Right-Pointing-Pointer Innovative multilayer system [TiN/TiAlN]n electrochemical

  10. Nature in corrosion–erosion surface for [TiN/TiAlN]n nanometric multilayers growth on AISI 1045 steel

    International Nuclear Information System (INIS)

    Caicedo, J.C.; Cabrera, G.; Caicedo, H.H.; Amaya, C.; Aperador, W.

    2012-01-01

    The aim of this work is to characterize the electrochemical behavior of [TiN/TiAlN]n multilayer coatings under corrosion–erosion condition. The multilayers with bilayer numbers (n) of 2, 6, 12, and 24 and/or bilayer period (Λ) of 1500 nm, 500 nm, 250 nm, 150 nm and 125 nm were deposited by magnetron sputtering technique on Si (100) and AISI 1045 steel substrates. Both, the TiN and the TiAlN structures for multilayer coatings were evaluated via X-ray diffraction analysis. Mechanical and tribological properties were evaluated via nanoindentation measurements and scratch test respectively. Silica particles were used as abrasive material on corrosion–erosion test in 0.5 M of H 2 SO 4 solution at impact angles of 30° and 90° over surface. The electrochemical characterization was carried out using polarization resistance technique (Tafel), in order to observe changes in corrosion rate as a function of the bilayer number (n) or the bilayer period (Λ) and the impact angle. Corrosion rate values of 9115 μm y for uncoated steel substrate and 2615 μm y for substrate coated with n = 24 (Λ = 125 nm) under an impact angle of 30° were found. On the other hand, for an impact angle of 90° the corrosion rate exhibited 16401 μm y for uncoated steel substrate and 5331 μm y for substrate coated with n = 24 (Λ = 125 nm). This behavior was correlated with the curves of mass loss for both coated samples and the surface damage was analyzed via scanning electron microscopy images for the two different impact angles. These results indicate that TiN/TiAlN multilayer coatings deposited on AISI 1045 steel represent a practical solution for applications in corrosive–erosive environments. - Highlights: ► Determination of superficial phenomenon that occurs in surface of multilayer films. ► Innovative multilayer system [TiN/TiAlN]n electrochemical response. ► Improvement of surface mechanical properties and response to surface corrosion attack. ► Nature of [TiN/TiAlN]n

  11. TiN-Coating Effects on Stainless Steel Tribological Behavior Under Dry and Lubricated Conditions

    Science.gov (United States)

    Zhang, Liqiang; Yang, Huisheng; Pang, Xiaolu; Gao, Kewei; Tran, Hai T.; Volinsky, Alex A.

    2014-04-01

    The tribological properties of magnetron sputtered titanium nitride coating on 316L steel, sliding against Si3N4 ceramic ball under dry friction and synthetic perspiration lubrication, were investigated. The morphology of the worn surface and the elemental composition of the wear debris were examined by scanning electron microscopy and energy dispersive spectroscopy. TiN coatings and 316L stainless steel had better tribological properties under synthetic perspiration lubrication than under dry friction. Among the three tested materials (316L, 1.6 and 2.4 μm TiN coatings), 2.4 μm TiN coating exhibits the best wear resistance. The difference in wear damage of the three materials is essentially due to the wear mechanisms. For the TiN coating, the damage is attributed to abrasive wear under synthetic perspiration lubrication and the complex interactive mechanisms, including abrasive and adhesive wear, along with plastic deformation, under dry friction.

  12. Hot deformation effect on the kinetics of austenite transformation under continuous cooling conditions

    International Nuclear Information System (INIS)

    Bernshtejn, M.L.; Zajmovskij, V.A.; Kisteh, N.V.; Samedov, O.V.; Faldin, S.A.

    1979-01-01

    The effect of hot deformation on the kinetics of austenite transformations in the commercial 4040Kh 40KhN, and 40KhNMA steels on continuous cooling was studied. The transformations were studied using a dilatometer of a special design which permits a specimen to be fixed quickly in holders after hot deformation. It is stated that in hot-deformed austenite the pearlite transformation proceeds at higher temperatures and in a narrower temperature range. Austenite deformation provides an opportunity to obtain a more fine ferrite-pearlite structure and ensures a uniform distribution of a structurally free ferrite in the steel bulk. The effect of hot deformation on the structure of ferrite decomposition products in the 40KhN and 40KhNMA steels is more complicated, which is connected with a substantial change in the kinetics of pearlite and intermediate transformations

  13. Superprotonic KH(PO3H)-SiO2 composite electrolyte for intermediate temperature fuel cells

    NARCIS (Netherlands)

    Bandarenka, A.; Bondarenko, Alexander S.; Zhou, W.; Bouwmeester, Henricus J.M.

    2009-01-01

    Novel thin film composite electrolyte membranes, prepared by dispersion of nano-sized SiO2 particles in the solid acid compound KH(PO3H), can be operated under both oxidizing and reducing conditions. Long-term stable proton conductivity is observed at not, vert, similar140 °C, i.e., slightly above

  14. Surface deformation effects on stainless steel, Ni, Cu and Mo produced by medium energy He ions irradiation

    International Nuclear Information System (INIS)

    Constantinescu, B.; Florescu, V.; Sarbu, C.

    1993-01-01

    To investigate dose and energy dependence of surface deformation effects (blistering and flaking), different kinds of candidate CTR first wall materials as 12KH18N10T, W-4541, W-4016 and SS-304 stainless steels, Ni, Cu, Mo were irradiated at room temperature with 3.0, 4.7 and 6.8 MeV He + ions at IAP Cyclotron. The effects were investigated by means of a TEMSCAN 200 CX electron microscope and two metallographic Orthoplan Pol Leitz and Olympus microscopes. We observed two dose dependent main phenomena: blistering and flaking (craters). So, blisters occurrence on the irradiated surface is almost instantaneous when a critical dose (number of He ions accumulated in the region at the end of alpha particles range) is reached. Increasing irradiation dose, we reached flaking stage. So, isolated submicronic fissures along grain boundaries were observed on the blister skin, chronologically followed by large (5-20 μm) deep cracks of hundreds of microns in length, blisters opening and, finally, flaking appearance. (author) 8 figs., 1 tab

  15. The heat treatment effect on the structural changes and properties of high-nitrogen chromium steels

    International Nuclear Information System (INIS)

    Blinov, V.M.; Elistratov, A.A.; Kolesnikov, A.G.; Rakhshtadt, A.G.; Plokhikh, A.I.; Morozova, E.I.; Kostina, M.V.

    2000-01-01

    The structural transformations in the steels with 0.4-1.3 %N and 15-24 %Cr content, originating by thermal treatment, are studied. The dependences of the phase composition of the high-chromium steels (18 %Cr) on the nitrogen content are established. The ratio of the unchanged austenite increases and the martensite quantity decreases correspondingly with growth of the nitrogen concentration from 0.4 up to 1.2 %. The effect of strengthening the steels with the initial martensite structure as well as austenite and martensite steels is observed in the process of steels tempering due to the hardening on the account of the martensite dispersion hardening [ru

  16. Review of time-dependent fatigue behavior and life prediction for 2 1/4 Cr-1 Mo steel

    International Nuclear Information System (INIS)

    Booker, M.K.; Majumdar, S.

    1982-01-01

    Available data on creep-fatigue life and fracture behavior of 2 1/4 Cr-1 Mo steel are reviewed. Whereas creep-fatigue interaction is important for Type 304 stainless steel, oxidation effects appear to dominate the time-dependent fatigue behavior of 2 1/4 Cr-1 Mo steel. Four of the currently available predictive methods - the Linear Damage Rule, Frequency Separation Equation, Strain Range Partitioning Equation, and Damage Rate Equation - are evaluated for their predictive capability. Variations in the parameters for the various predictive methods with temperature, heat of material, heat treatment, and environment are investigated. Relative trends in the lives predicted by the various methods as functions of test duration, waveshape, etc., are discussed. The predictive methods will need modification in order to account for oxidation and aging effects in the 2 1/4 Cr-1 Mo steel. Future tests that will emphasize the difference between the various predictive methods are proposed

  17. Structure and Properties of Burnished and Nitrided AISI D2 Tool Steel

    Directory of Open Access Journals (Sweden)

    Daniel TOBOŁA

    2015-11-01

    Full Text Available D2 belongs to traditional steels, frequently used in metalworking industry. Shot peening and nitriding are known to improve the wear resistance of D2. In this work we focus on processes of slide burnishing and industrial low temperature gas nitriding. The D2 steel specimens were first subjected to heat treatments (HT prescribed by the manufacturer, turning (T, then burnishing (B and nitriding (N. The reason for turning was achieving appropriate surface roughness. Deformation induced in slide burnishing can be better controlled then in shot peening because of deterministic nature of this process. Four different paths to prepare surfaces were employed: HT + T, HT + T + B, HT + T + N, HT + T + B + N. D2 steel is very sensitive to the final finishing, wear rates vary up to 300 %. Two of our procedures (HT + T + N and HT + T + B + N are much superior to the others. Moreover, in the HT + T + N case, apparently the surface fatigue scaling off takes place.DOI: http://dx.doi.org/10.5755/j01.ms.21.4.7224

  18. Changes in mechanical properties and structure of electrolytic plasma treated X 12 CrNi 18 10 Ti stainless steel

    Energy Technology Data Exchange (ETDEWEB)

    Kurbanbekov, Sherzod; Baklanov, Viktor; Karakozov, Batyrzhan [Republican State Enterprise National Nuclear Center of Kazakhstan, Kurchatov (Kazakhstan). Inst. of Atomic Energy Branch; Skakov, Mazhyn [Republican State Enterprise National Nuclear Center of Kazakhstan, Kurchatov (Kazakhstan)

    2017-05-01

    The paper addresses findings regarding the influence of electrolytic plasma treatment on the mechanical properties as well as structural and phase states of X 12 CrNi 18 10 Ti steel. Electrolytic plasma treatment is based on carburizing of stainless steel heated in electrolytes. Treatment of steel samples has been performed as follows: the samples were heated up to a temperature between 850 and 950 C and then they were cured for 7 minutes in an electrolyte of an aqueous solution containing 10 % glycerol (C{sub 3}H{sub 8}O{sub 3}) and 15 % sodium carbonate (Na{sub 2}CO{sub 3}). It is found that, after plasma electrolytic treatment, the surface of X 12 CrNi 18 10 Ti steel had a modified structure and high hardness. Increasing wear resistance of X 12 CrNi 18 10 Ti steel has been observed after carburizing and the coefficient of friction has been reduced. X-ray analysis showed that retained austenite γ-Fe is a main phase, and there are some diffraction lines of orthorhombic Fe{sub 3}C phase as well as Fe{sub 3}O{sub 4} cubic phase. It has been determined, that, after plasma electrolytic treatment, a carbide phase in the modified surface layer, irrespective of the location in the steel structure has the chemical composition Fe{sub 3}C. High concentration of carbon atoms in a solid solution based on γ- and α-iron, a large dislocation density, presence of particles of carbide phase and retained austenite layers have been found.

  19. Analysis of nature of brazed joints fracture under operating conditions

    International Nuclear Information System (INIS)

    Orlov, A.V.; Gura, P.M.

    1985-01-01

    Technique establishing causes leading to brazed joint fracture in pressure boundary components, operating under heavy conditions of high temperature and corrosive medium is described. Some cases of tube brazed joint fractures in a superheater of 12Kh1MF and 08Kh18N10T steels are considered. The attention is paid on using metallography for determination of mechanical or corrosion fracture properties. The diagram is developed permitting to take into account the interrelation between the fracture area in the given zone and its strength

  20. Design of joints in steel and composite structures Eurocode 3 : design of steel structures : part 1-8 : design of joints, Eurocode 4 : design of composite steel and concrete structures : part 1-1 : general rules and rules for buildings

    CERN Document Server

    Jaspart, Jean-Pierre

    2016-01-01

    This book details the basic concepts and the design rules included in Eurocode 3 Design of steel structures Part 1-8 Design of joints. Joints in composite construction are also addressed through references to Eurocode 4 Design of composite steel and concrete structures Part 1-1 General rules and rules for buildings. Attention has to be duly paid to the joints when designing a steel or composite structure, in terms of the global safety of the construction, and also in terms of the overall cost, including fabrication, transportation and erection. Therefore, in this book, the design of the joints themselves is widely detailed, and aspects of selection of joint configuration and integration of the joints into the analysis and the design process of the whole construction are also fully covered. Connections using mechanical fasteners, welded connections, simple joints, moment-resisting joints and lattice girder joints are considered. Various joint configurations are treated, including beam-to-column, beam-to-beam, ...

  1. An improved synthesis of 4-[18F]-ADAM, a potent serotonin transporter imaging agent

    International Nuclear Information System (INIS)

    Huang, Y.-Y.; Huang, W.-S.; Chu, T.-C.; Shiue, C.-Y.

    2009-01-01

    An improved synthesis of N,N-dimethyl-2-(2-amino-4-[ 18 F]fluorophenylthio)benzylamine (4-[ 18 F]-ADAM, 2) as a potent serotonin transporter (SERT) imaging agent is described. Molecular orbital (MO) calculation predicts that N,N-dimethyl-2- (2-nitro-4-trimethylammoniumtrifluoromethanesulfonylphenylthio)benzamide (8) is probably a better precursor than N,N-dimethyl-2-(2,4-dinitrophenylthio)benzylamine (1) for preparing 2. Radioligand 2 was synthesized by the reaction of either precursor 1 or precursor 8 with K[ 18 F]/K 2.2.2 at 120 deg. C followed by reduction with BH 3 at 80 deg. C. The radiochemical yield (EOB) of 2 synthesized from precursor 1 and 8 was 5.7±2.4% (n=6) and 14.8±4.0% (n=5), respectively, in a synthesis time of 120 min from EOB. The specific activity of 2 was 3 Ci/μmol or 111 GBq/μmol (EOB). Thus, this new synthetic method has significantly improved the radiochemical yield of 4-[ 18 F]-ADAM and makes this radioligand more accessible to PET Centers without a cyclotron.

  2. Compound effect of CaCO3 and CaSO4·2H2O on the strength of steel slag: cement binding materials

    International Nuclear Information System (INIS)

    Qi, Liqian; Liu, Jiaxiang; Liu, Qian

    2016-01-01

    In this study, we replaced 30% of the cement with steel slag to prepare binding material; additionally, small amounts of CaCO 3 and CaSO 4 ·2H 2 O were added. This was done to study the compound effect of CaCO 3 and CaSO 4 ·2H 2 O on the strength of steel slag-cement binding materials. The hydration degree of the steel slag cementitious material was analyzed by XRD, TG and SEM. The results showed that the optimum proportions of CaCO 3 and CaSO 4 ·2H 2 O were 3% and 2%, respectively. Compared with the steel slag-cement binders without adding CaCO 3 and CaSO 4 ·2H 2 O, the compressive strength increased by 59.9% at 3 days and by 17.8% at 28 days. Acting as the nucleation matrix, CaCO 3 could accelerate the hydration of C 3 S. In addition, CaCO 3 was involved in the hydration reaction, generating a new hydration product, which could stably exist in a slurry. Meanwhile, CaSO 4 ·2H 2 O could increase the number of AFt. The compound effect of CaCO 3 and CaSO 4 ·2H 2 O enhanced the intensity of steel slag-cement binding materials and improved the whole hydration behavior. (author)

  3. (4,4′-Dimethoxy-2,2′-bipyridine-κ2N,N′bis[2-(pyridin-2-ylphenyl-κC1]iridium(III hexafluoridophosphate unknown solvate

    Directory of Open Access Journals (Sweden)

    Yano Natsumi

    2016-03-01

    Full Text Available The asymmetric unit of the title complex, [Ir(C11H8N2(C12H12N2O2]PF6, comprises a [Ir(ppy2(diMeO-bpy]+ cation (Hppy = 2-phenylpyridine and diMeO-bpy = 4,4′-dimethoxy-2,2′-bipyridine and a PF6− anion. The IrIII atom is coordinated by two anionic ppy− ligands, each coordinating in a C^N cyclometalated mode, and one neutral diMeO-bpy ligand, leading to a distorted octahedral geometry defined by a cis-C2N4 donor set. Intermolecular C—F...H contacts lead to a three-dimensional architecture that define columns parallel to a. Unknown disordered solvent molecules reside in these columns with the electron density being treated with SQUEEZE [Spek (2015. Acta Cryst. C71, 9–18]. The unit-cell data do not reflect the presence of the unresolved solvent.

  4. ¿Hacia dónde va la integración?

    Directory of Open Access Journals (Sweden)

    Alberto Acosta

    2015-01-01

    Full Text Available La ola integracionista se filtra por todas partes, en especial, en la formación de bloques económicos. Los periodistas juegan un papel importante como agentes dinamizadores. Aborda el Plan Bush vs. Integración, la crisis de la hegemonía a la integración, limitaciones del desarrollo dependiente. Responde a la pregunta de ¿Hacia donde va la integración en América latina? Advierte que la integración deberá construirse sobre una movilización ideológica en tormo a la definición de objetivos y metas que hagan posible las transformaciones en todas las sociedades involucradas.

  5. VA/Q distribution during heavy exercise and recovery in humans: implications for pulmonary edema

    Science.gov (United States)

    Schaffartzik, W.; Poole, D. C.; Derion, T.; Tsukimoto, K.; Hogan, M. C.; Arcos, J. P.; Bebout, D. E.; Wagner, P. D.

    1992-01-01

    Ventilation-perfusion (VA/Q) inequality has been shown to increase with exercise. Potential mechanisms for this increase include nonuniform pulmonary vasoconstriction, ventilatory time constant inequality, reduced large airway gas mixing, and development of interstitial pulmonary edema. We hypothesized that persistence of VA/Q mismatch after ventilation and cardiac output subside during recovery would be consistent with edema; however, rapid resolution would suggest mechanisms related to changes in ventilation and blood flow per se. Thirteen healthy males performed near-maximal cycle ergometry at an inspiratory PO2 of 91 Torr (because hypoxia accentuates VA/Q mismatch on exercise). Cardiorespiratory variables and inert gas elimination patterns were measured at rest, during exercise, and between 2 and 30 min of recovery. Two profiles of VA/Q distribution behavior emerged during heavy exercise: in group 1 an increase in VA/Q mismatch (log SDQ of 0.35 +/- 0.02 at rest and 0.44 +/- 0.02 at exercise; P less than 0.05, n = 7) and in group 2 no change in VA/Q mismatch (n = 6). There were no differences in anthropometric data, work rate, O2 uptake, or ventilation during heavy exercise between groups. Group 1 demonstrated significantly greater VA/Q inequality, lower vital capacity, and higher forced expiratory flow at 25-75% of forced vital capacity for the first 20 min during recovery than group 2. Cardiac index was higher in group 1 both during heavy exercise and 4 and 6 min postexercise. However, both ventilation and cardiac output returned toward baseline values more rapidly than did VA/Q relationships. Arterial pH was lower in group 1 during exercise and recovery. We conclude that greater VA/Q inequality in group 1 and its persistence during recovery are consistent with the hypothesis that edema occurs and contributes to the increase in VA/Q inequality during exercise. This is supported by observation of greater blood flows and acidosis and, presumably therefore

  6. Electrochemical impedance spectrometry using Inconel 690, zircaloy 4, 316Ti steel, 17-4-PH, UR52N et URSB8. Simulation in tritiated water. Tome 1

    International Nuclear Information System (INIS)

    Bellanger, G.

    1994-11-01

    The redox potential of 3 H 2 O, as well as the corrosion potentials in this medium are found, abnormally, in the trans-passive region. This is completely different from the behavior in the chemical industry or in the water in nuclear powers. With such behavior, there will be breakdowns of the protective oxide layers, and in the presence of chloride there will be immediate pitting. Polarization and electrochemical impedance spectrometry curves are presented and discussed. These curves make it possible to ascertain the corrosion domains and to compare the kinetics of different stainless alloys. These corrosion kinetics and the corrosion potentials provide a classification of the steels studied here: Inconel 690, zircaloy 4, 316 Ti steel, 17-4-PH, UR52N et URSB8. From the results it can be concluded that URSB8 has the best corrosion resistance. (author). 279 figs., tabs

  7. Creep and long-term strength of heat-resistant steels with different structures with the account taken of the type of stress deviator

    International Nuclear Information System (INIS)

    Giginyak, F.F.; Dragunov, Yu.G.; Mozharovskaya, T.N.; Titov, V.F.

    1993-01-01

    The results of the experimental investigations into creep and long-term strength of heat-resistant steels 15Kh2MFA and 15Kh2NMFA in the initial state and after heat-treatment simulating the metal irradiation embrittlement at the end of the product service date under static loading at the complex stress state and at high temperatures are presented. The experimentally substantiated equations of state describing creep and long-term stability of materials taking into account the type of the stress state are derived. (author)

  8. N,N-Diethyl-2-[5-(4-methoxybenzylidene-2,4-dioxo-1,3-thiazolidin-3-yl]acetamide

    Directory of Open Access Journals (Sweden)

    Vijayan Viswanathan

    2017-05-01

    Full Text Available In the title compound, C17H20N2O4S, the thiazolidine (r.m.s. deviation = 0.022 Å and phenyl rings (major and minor occupancies are inclined to one another by 6.3 (3 and 10.5 (3°, respectively. The molecular conformation is stabilized by an intramolecular C—H...S interaction. In the crystal, molecules are linked by C—H...O hydrogen bonds, which generate R22(18, R22(24 and R21(7 ring motifs. Aromatic π–π stacking interactions are also observed.

  9. Mutation and crystallization of the first KH domain of human polycytosine-binding protein 1 (PCBP1) in complex with DNA

    International Nuclear Information System (INIS)

    Yoga, Yano M. K.; Traore, Daouda A. K.; Wilce, Jacqueline A.; Wilce, Matthew C. J.

    2011-01-01

    The successful preparation of a mutant KH domain representing the first KH domain of PCBP1 and its crystallization in complex with a C-rich DNA are reported. This structure is anticipated to provide high-resolution information that will allow better understanding of the basis of cytosine specificity by PCBPs. Polycytosine-binding proteins (PCBPs) are triple KH-domain proteins that play an important role in the regulation of translation of eukaryotic mRNA. They are also utilized by viral RNA and have been shown to interact with ssDNA. Underlying their function is the specific recognition of C-rich nucleotides by their KH domains. However, the structural basis of this recognition is only partially understood. Here, the preparation of a His-tagged KH domain is described, representing the first domain of PCBP1 that incorporates a C54S mutation as well as the addition of a C-terminal tryptophan. This construct has facilitated the preparation of highly diffracting crystals in complex with C-rich DNA (sequence ACCCCA). Crystals of the KH1–DNA complex were grown using the hanging-drop vapour-diffusion method in 0.1 M phosphate–citrate pH 4.2, 40%(v/v) PEG 300. X-ray diffraction data were collected to 1.77 Å resolution and the diffraction was consistent with space group P2 1 , with unit-cell parameters a = 38.59, b = 111.88, c = 43.42 Å, α = γ = 90.0, β = 93.37°. The structure of the KH1–DNA complex will further our insight into the basis of cytosine specificity by PCBPs

  10. Detection of Infectious Bronchitis Virus (4/91 type in Broiler Chickens in Chahrmahal-va-bakhtiyari Province

    Directory of Open Access Journals (Sweden)

    M Gholami-Ahangaran

    2012-08-01

    Full Text Available Infectious bronchitis (IB disease is a viral contagious respiratory disease. The causing agent of this disease has several serotypes. In this study, 4/91 type of Infectious bronchitis (IB was identified. For this, tracheal samples were taken from 18 broiler chickens flocks having respiratory signs suspected to IB disease with one percent mortality in day. After RNA extraction from tissue samples in one step RT-PCR reaction, a fragment of S1 gene was amplified by common primers for all IB viruses. Then RT-PCR product was amplified for identification of 4/91(793/B type by type specific primers in Nested-PCR. Results showed, 11 out 18 flocks (61.1% were infected to IB that 45.45% of IB infected flocks were infected to 4/91 type. Therefore it seems 4/91 type of IB has role in forming and complexing of respiratory signs in broiler chickens suffering to respiratory syndrome in Chahrmahal-va-bakhtiyari province and it is necessary to give a suitable controlling strategy for prevention of 4/91 infection.

  11. Effect of χ Phase Formation on the Mechanical Properties of 25Cr-7Ni-4Mo-0.2N Super Duplex Stainless Steel

    International Nuclear Information System (INIS)

    Kang, Chang Yong; Kim, Jae Hwan

    2011-01-01

    This study was carried out to investigate the precipitation behavior of χ phase and effect of χ-phase which precipitated at the initial stage of aging on mechanical properties of 25%Cr-7%Ni-4%Mo-0.2%N super duplex stainless steel. χ-phase was precipitated mainly at the interface of ferrite / austenite phases and inside of the ferrite phase at the initial stage of aging, and it was transformed into σ-phase with an increase of aging time. The ferrite phase was decomposed into new austenite(γ 2 )phase and σ-phase by aging treatment. The hardness and tensile strength of the initial stage of aging when χ-phase was precipitated did not changed considerably, while elongation rapidly decreased. Accordingly, it is considered that χ-phase didn't affect the hardness and strength significantly, but it affected the elongation.

  12. Corrosion of 316 stainless steel in high temperature molten Li{sub 2}BeF{sub 4} (FLiBe) salt

    Energy Technology Data Exchange (ETDEWEB)

    Zheng, Guiqiu, E-mail: guiqiuzheng@gmail.com; Kelleher, Brian; Cao, Guoping; Anderson, Mark; Allen, Todd; Sridharan, Kumar

    2015-06-15

    In support of structural material development for the fluoride-salt-cooled high-temperature reactor (FHR), corrosion tests of 316 stainless steel were performed in the potential primary coolant, molten Li{sub 2}BeF{sub 4} (FLiBe) at 700 °C for an exposure duration up to 3000 h. Tests were performed in both 316 stainless steel and graphite capsules. Corrosion in both capsule materials occurred by the dissolution of chromium from the stainless steel into the salt which led to the depletion of chromium predominantly along the grain boundaries of the test samples. The samples tested in graphite capsules showed a factor of two greater depth of corrosion attack as measured in terms of chromium depletion, compared to those tested in 316 stainless steel capsules. The samples tested in graphite capsules showed the formation of Cr{sub 7}C{sub 3} particulate phases throughout the depth of the corrosion layer. Samples tested in both types of capsule materials showed the formation of MoSi{sub 2} phase due to increased activity of Mo and Si as a result of Cr depletion, and furthermore corrosion promoted the formation of a α-ferrite phase in the near-surface regions of the 316 stainless steel. Based on the corrosion tests, the corrosion attack depth in FLiBe salt was predicted as 17.1 μm/year and 31.2 μm/year for 316 stainless steel tested in 316 stainless steel and in graphite capsules respectively. It is in an acceptable range compared to the Hastelloy-N corrosion in the Molten Salt Reactor Experiment (MSRE) fuel salt.

  13. Study of nitrogen solubility in multicomponent iron alloys at its pressure in gaseous phase up to 1000kPa

    International Nuclear Information System (INIS)

    Pomarin, Yu.M.; Grigorenko, G.M.; Latash, Yu.V.; Kanibolotskij, S.A.

    1983-01-01

    A facility in which metal is melted in a weighed state and nitrogen partical pressure during relting may be charge from 0 to 1000 kPa is developed to investigate nitrogen solubility is liquim metals and alloys. Investigation of nitrogen solubility was performed using samples of 03Kh25N5AM3 steel and Kh20N5, Kh20N10, Kh40N10, Kh40N20 alloys. Positive deflection of [N]=f(√Psub(Nsub(2))) dependence from the Henry law is shown to be observed in the Kh40N10 alloy in the 100-1000 kPa pressure range. In this case the vatue of positive deflection decreases with temperature growth and at T=2273 K nitrogen solubility in the alloy submits to the law of square root. An equation permitting to calculate nitrogen solubility in alloys of Fe-Cr-Ni and Fe-Cr-Mn systems in the 0 to 1000 kPa range of nitrogen partial pressures is obtained

  14. N,N-Diethylanilinium 2,4-dioxo-5-(2,4,6-trinitrophenyl-1,2,3,4-tetrahydropyrimidin-6-olate

    Directory of Open Access Journals (Sweden)

    Manickam Buvaneswari

    2011-12-01

    Full Text Available In the crystal structure of the title molecular salt, C10H16N+·C10H4N5O9−, the components are linked through a N—H...O hydrogen bonds. R22(8 ring motifs are formed between inversion-related barbiturate residues. Two intramoleculer N—H...O hydrogen bonds are observed in the anion. The dihedral angle between 2,4,6-trinitrophenyl and barbiturate rings is 53.6 (2°. The N,N-diethylamine substituent is disordered and was modeled as two geometrically equivalent conformers with occupancies of 0.737 (2 and 0.273 (2.

  15. Radiolabelling of isopeptide Nε-(γ-glutamyl)-L-lysine by conjugation with N-succinimidyl-4-[18F]fluorobenzoate

    International Nuclear Information System (INIS)

    Wuest, F.; Hultsch, C.; Bergmann, R.; Johannsen, B.; Henle, T.

    2003-01-01

    The isopeptide N ε -(γ-glutamyl)-L-lysine 4 was labelled with 18 F via N-succinimidyl-4-[ 18 F]fluorobenzoate ([ 18 F]SFB). A modified approach for the convenient synthesis of [ 18 F]SFB was used, and [ 18 F]SFB could be obtained in decay-corrected radiochemical yields of 44-53% (n=20) and radiochemical purity >95% within 40 min after EOB. For labelling N ε -(γ-glutamyl)-L-lysine with [ 18 F]SFB the effects of isopeptide concentration, temperature, and pH were studied to determine the optimum reaction conditions. The coupling reaction was shown to be temperature and pH independent while being strongly affected by the isopeptide concentration. Using the optimized labelling conditions, in a typical experiment 1.3 GBq of [ 18 F]SFB could be converted into 447 MBq (46%, decay-corrected) of [ 18 F]fluorobenzoylated isopeptide within 45 min, including HPLC purification

  16. EXPOSICIÓN AL MONÓXIDO DE CARBONO DEL PERSONAL ESPECIALISTA EN EXTINCIÓN DE INCENDIOS FORESTALES

    Directory of Open Access Journals (Sweden)

    Belén Carballo Leyenda

    2010-01-01

    Full Text Available Fundamento: Se ha descrito que la salud y el rendimiento laboral del personal dedicado a la extinción de los incendios forestales se ven perjudicados principalmente por el monóxido de carbono (CO. El objetivo de este trabajo ha sido analizar la exposición al CO a la que se ve sometido el personal especialista en la extinción de los incendios. Métodos: Durante 58 incendios reales se monitorizó en 44 sujetos la exposición al CO a la que se vieron sometidos. También se analizó la concentración ponderada para una jornada de 8h (VA-ED. Todos los incendios fueron divididos en función del tipo de trabajo realizado (ataque directo, indirecto y combinado y del combustible presente (pasto, matorral, bajo arbolado y mixto. Las variables analizadas fueron estudiadas mediante la prueba de Kruskal-Wallis, se usó el test de Mann-Whitney para establecer las diferencias entre medias. Resultados: La concentración media de CO en los incendios fue de 18,4±1,7 ppm, lo que supuso una VA-ED de 7,0±1,0 ppm. Las mayores exposiciones al CO se analizaron en los ataques combinados (20,4±2,3 ppm seguidas de las obtenidas en los ataques directos (17,5±2,7 ppm e indirectos (10,6±5,4 ppm. Únicamente se obtuvieron diferencias significativas (p<0,05 al comparar las exposiciones al CO generadas por la combustión del matorral (19,8±2,2 y bajo arbolado (17,2±3,9 y pasto (12,0±5,6. Conclusiones: Las exposiciones de CO analizadas se vieron influidas por el tipo de combustible y trabajo desempeñado. Los valores medios obtenidos se situaron dentro de los límites establecidos como seguros por diferentes organismos nacionales (INSHT e internacionales (NIOSH, OSHA.

  17. Biotransformation of 2,4-dinitroanisole by a fungal Penicillium sp.

    Science.gov (United States)

    Schroer, Hunter W; Langenfeld, Kathryn L; Li, Xueshu; Lehmler, Hans-Joachim; Just, Craig L

    2017-02-01

    Insensitive munitions explosives are new formulations that are less prone to unintended detonation compared to traditional explosives. While these formulations have safety benefits, the individual constituents, such as 2,4-dinitroanisole (DNAN), have an unknown ecosystem fate with potentially toxic impacts to flora and fauna exposed to DNAN and/or its metabolites. Fungi may be useful in remediation and have been shown to degrade traditional nitroaromatic explosives, such as 2,4,6-trinitrotoluene and 2,4-dinitrotoluene, that are structurally similar to DNAN. In this study, a fungal Penicillium sp., isolated from willow trees and designated strain KH1, was shown to degrade DNAN in solution within 14 days. Stable-isotope labeled DNAN and an untargeted metabolomics approach were used to discover 13 novel transformation products. Penicillium sp. KH1 produced DNAN metabolites resulting from ortho- and para-nitroreduction, demethylation, acetylation, hydroxylation, malonylation, and sulfation. Incubations with intermediate metabolites such as 2-amino-4-nitroanisole and 4-amino-2-nitroanisole as the primary substrates confirmed putative metabolite isomerism and pathways. No ring-cleavage products were observed, consistent with other reports that mineralization of DNAN is an uncommon metabolic outcome. The production of metabolites with unknown persistence and toxicity suggests further study will be needed to implement remediation with Penicillium sp. KH1. To our knowledge, this is the first report on the biotransformation of DNAN by a fungus.

  18. Studies on adsorption and corrosion inhibitive properties of quinoline derivatives on N80 steel in 15% hydrochloric acid

    Directory of Open Access Journals (Sweden)

    K.R. Ansari

    2016-12-01

    Full Text Available This paper deals with the N80 steel corrosion protection study in 15% HCl which was carried by three quinoline derivatives namely 3-acetyl-1-(4-methylbenzylideneamino quinolin-2-one (AQ-1, 3-acetyl-1-(4 hydroxy benzylideneamino quinolin-2-one (AQ-2, 3-acetyl-1-(3-nitrobenzylideneamino quinolin-2(1H-one (AQ-3 using gravimetric, electrochemical, and quantum chemical studies. Tafel polarization showed that AQs are mixed type inhibitors but dominantly affect cathodic reaction more. The observed results reveal that AQ-1 is the best inhibitor. All the three inhibitors were found to obey the Langmuir adsorption isotherm. Scanning electron microscopy (SEM micrographs supports the protection of the N80 steel by AQs. Quantum chemical study reveals that the inhibitors have a tendency to get protonated and this protonated form has greater tendency to get adsorbed onto the N80 steel surface.

  19. Corrosion Fatigue Characteristics of 12Cr Alloy Steel in Na2SO4 Solution

    Science.gov (United States)

    Bae, D. H.; Cho, S. Y.

    In order to estimate reliability of 12Cr alloy steel using as the turbine blade material of the steam power plant, its corrosion fatigue characteristics in Na2SO4 solution considering its percentage and temperature that were determined from the polarization test results were investigated, and compared with the results in air. The corrosion characteristic of 12Cr alloy steel was remarkably susceptible in 12.7wt.% (IM) Na2SO4 solution, and its susceptibility increased with the solution temperature increase. The corrosion fatigue characteristics in 12.7wt.% Na2SO4 solution were similar to that of in air at 25°C. The crack growth rate was however increased with the temperature of solution increase. The reasons showing such results are due to the difference of the crack growth mechanism according to the electro-chemical activity of the corrosion factors.

  20. Corrosion of N80 carbon steel in oil field formation water containing CO2 in the absence and presence of acetic acid

    International Nuclear Information System (INIS)

    Zhu, S.D.; Fu, A.Q.; Miao, J.; Yin, Z.F.; Zhou, G.S.; Wei, J.F.

    2011-01-01

    Highlights: → Effects of temperature and HAc concentration on N80 carbon steel were investigated. → Temperature increased corrosion rate of N80 and precipitation rate of FeCO 3 . → HAc increased corrosion rate of N80 and enhanced the local corrosion attack (pitting). → FeCO 3 was still the main composition of corrosion products in the presence of HAc. → There was a transition region between CO 2 corrosion control and HAc corrosion control. - Abstract: Corrosion behaviour of N80 carbon steel in formation water containing CO 2 was studied by polarization curve technique, electrochemical impedance spectroscopy, weight loss test, scanning electron microscope, and X-ray diffraction. Effects of temperature and acetic acid concentration on the corrosion behaviour of N80 carbon steel were discussed. The results showed that increasing temperature not only enhanced the dissolution of steel substrate, but also promoted the precipitation of FeCO 3 , the addition of acetic acid enhanced localized corrosion attack on N80 carbon steel. FeCO 3 was the main corrosion product. And there was a transition region between CO 2 corrosion control and HAc corrosion control.

  1. Tribological properties and surface structures of ion implanted 9Cr18Mo stainless steels

    Science.gov (United States)

    Fengbin, Liu; Guohao, Fu; Yan, Cui; Qiguo, Sun; Min, Qu; Yi, Sun

    2013-07-01

    The polished quenched-and-tempered 9Cr18Mo steels were implanted with N ions and Ti ions respectively at a fluence of 2 × 1017 ions/cm2. The mechanical properties of the samples were investigated by using nanoindenter and tribometer. The results showed that the ion implantations would improve the nanohardness and tribological property, especially N ion implantation. The surface analysis of the implanted samples was carried out by using XRD, XPS and AES. It indicated that the surface exhibits graded layers after ion implantation. For N ion implantation, the surface about 20 nm thickness is mainly composed of supersaturated interstitial N solid solution, oxynitrides, CrxCy phase and metal nitrides. In the subsurface region, the metal nitrides dominate and the other phases disappear. For Ti ion implantation, the surface of about 20 nm thickness is mainly composed of titanium oxides and carbon amorphous phase, the interstitial solid solution of Ti in Fe is abundant in the subsurface region. The surface components and structures have significant contributions to the improved mechanical properties.

  2. Tribological properties and surface structures of ion implanted 9Cr18Mo stainless steels

    International Nuclear Information System (INIS)

    Fengbin, Liu; Guohao, Fu; Yan, Cui; Qiguo, Sun; Min, Qu; Yi, Sun

    2013-01-01

    The polished quenched-and-tempered 9Cr18Mo steels were implanted with N ions and Ti ions respectively at a fluence of 2 × 10 17 ions/cm 2 . The mechanical properties of the samples were investigated by using nanoindenter and tribometer. The results showed that the ion implantations would improve the nanohardness and tribological property, especially N ion implantation. The surface analysis of the implanted samples was carried out by using XRD, XPS and AES. It indicated that the surface exhibits graded layers after ion implantation. For N ion implantation, the surface about 20 nm thickness is mainly composed of supersaturated interstitial N solid solution, oxynitrides, Cr x C y phase and metal nitrides. In the subsurface region, the metal nitrides dominate and the other phases disappear. For Ti ion implantation, the surface of about 20 nm thickness is mainly composed of titanium oxides and carbon amorphous phase, the interstitial solid solution of Ti in Fe is abundant in the subsurface region. The surface components and structures have significant contributions to the improved mechanical properties

  3. Stainless steels for cryogenic bolts and nuts

    International Nuclear Information System (INIS)

    Leroy, F.; Rabbe, P.; Odin, G.

    1975-01-01

    Stainless steel for cryogenic applications are generally austenitic steels which, under the effect of cold-drawing, can or cannot undergo a partial martensitic transformation according to their composition. It has been shown that very high ductility and endurance characteristics at low temperatures, together with very high yield strength and resistances values, can be attained with grades of nitrogenous steels of types Z2CN18-10N and Z3CMN18-8-6N. Optimum ductility values are obtained by employing to the best possible, the martensitic transformations which develop during cold-drawing. From the plotting of the rational traction curves, it is possible to analyse very simply the influence of the composition on the martensitic transformations [fr

  4. N,N-Dihexyl-4-[2-(4-nitrophenylvinyl]aniline

    Directory of Open Access Journals (Sweden)

    Dieter Schollmeyer

    2011-06-01

    Full Text Available The title compound, C26H36N2O2, was prepared by Horner olefination of p-dihexylaminobenzaldehyde and diethyl p-nitrobenzylphosphonate. It crystallizes with two independent molecules in the asymmetric unit. Both have similar geometries of the π-systems but the conformations of all hexyl chains are different. Whereas one hexyl chain of the first molecule shows the typical all-anti conformation, the second is arranged in a gauche-anti-gauche-anti conformation with N—C—C—C, C—C—C—C, C—C—C—C and C—C—C—C torsion angles of −65.1 (4, 167.3 (3, 63.3 (4, and 179.4 (3°. One of the hexyl chains in the other molecule has an anti-anti-gauche-anti conformation [N—C—C—C, C—C—C—C, C—C—C—C and C—C—C—C torsion angles = 179.6 (3, −179.8 (3, −68.7 (5 and −178.8 (4°], the other starts with an anti-gauche-gauche sequence. Molecules A and B are composed of five planar subunits. The angle sums around the N atoms are in the range 356 (2–360.0 (2°. Torsion angles between these segments do not exceed 4.9 (4°, except for one of the alkyl chains each [molecule A = 26.2 (4°; molecule B = −6.0 (4°]. The high planarity of the molecules and the short aniline C—N bonds [1.385 (3 Å in molecule A and 1.378 (3 Å in molecule B] indicate a strong electronic coupling through the stilbene unit. One methylene group is disordered over two positions with an occupancy ratio of 0.72:0.28.

  5. Determination of ultra-short laser induced damage threshold of KH2PO4 crystal: Numerical calculation and experimental verification

    Directory of Open Access Journals (Sweden)

    Jian Cheng

    2016-03-01

    Full Text Available Rapid growth and ultra-precision machining of large-size KDP (KH2PO4 crystals with high laser damage resistance are tough challenges in the development of large laser systems. It is of high interest and practical significance to have theoretical models for scientists and manufacturers to determine the laser-induced damage threshold (LIDT of actually prepared KDP optics. Here, we numerically and experimentally investigate the laser-induced damage on KDP crystals in ultra-short pulse laser regime. On basis of the rate equation for free electron generation, a model dedicated to predicting the LIDT is developed by considering the synergistic effect of photoionization, impact ionization and decay of electrons. Laser damage tests are performed to measure the single-pulse LIDT with several testing protocols. The testing results combined with previously reported experimental data agree well with those calculated by the model. By taking the light intensification into consideration, the model is successfully applied to quantitatively evaluate the effect of surface flaws inevitably introduced in the preparation processes on the laser damage resistance of KDP crystals. This work can not only contribute to further understanding of the laser damage mechanisms of optical materials, but also provide available models for evaluating the laser damage resistance of exquisitely prepared optical components used in high power laser systems.

  6. Fabrication of Hadfield-Cored Multi-layer Steel Sheet by Roll-Bonding with 1.8-GPa-Strength-Grade Hot-Press-Forming Steel

    Science.gov (United States)

    Chin, Kwang-Geun; Kang, Chung-Yun; Park, Jaeyeong; Lee, Sunghak

    2018-05-01

    An austenitic Hadfield steel was roll-bonded with a 1.8-GPa-strength-grade martensitic hot-press-forming (HPF) steel to fabricate a multi-layer steel (MLS) sheet. Near the Hadfield/HPF interface, the carburized and decarburized layers were formed by the carbon diffusion from the Hadfield (1.2%C) to HPF (0.35%C) layers, and could be regarded as kinds of very thin multi-layers of 35 μm in thickness. The tensile test and fractographic data indicated that the MLS sheet was fractured abruptly within the elastic range by the intergranular fracture occurred in the carburized layer. This was because C was mainly segregated at prior austenite grain boundaries in the carburized layer, which weakened grain boundaries to induce the intergranular fracture. In order to solve the intergranular facture problem, the MLS sheet was tempered at 200 °C. The stress-strain curve of the tempered MLS sheet lay between those of the HPF and Hadfield sheets, and a rule of mixtures was roughly satisfied. Tensile properties of the MLS sheet were dramatically improved after the tempering, and the intergranular fracture was erased completely. In particular, the yield strength up to 1073 MPa along with the high strain hardening and excellent ductility of 32.4% were outstanding because the yield strength over 1 GPa was hardly achieved in conventional austenitic steels.

  7. Surface finishing and levelling of thermomechanically hardened rolled steel

    International Nuclear Information System (INIS)

    Grosval'd, V.G.; Bashchenko, A.P.; Grishkov, A.I.; Gutnik, M.V.; Kanevskij, B.L.; Nikozov, A.I.; Sedov, N.D.; Prosin, K.A.; Safonov, L.I.

    1975-01-01

    The finishing of high-strength merchant shapes from alloy steel was tried out under industrial conditions with the equipment of metallurgical plants. After thermomechanical hardening in the production line of the rolling mill, 30KhGSN2A and 40Kh1NVA steel rounds 32 and 31 mm in diameter were straightened on a two-roller straightening machine designed by the All-Union Scientific Research Institute for Metallurgical Machinery (VNII Metmash). This made possible subsequent turning and grinding of the rods. The conditions of straightening, turning and grinding have been worked so as to obtain thermomechanically strengthened and ground rolled products approximating the gauged and ground metal in shape geometry and surface finish. It is shown that the labour-consuming operation of turning can be eliminated by reducing the machining pass of the rolled product, and this lowers the labour required for the finishing operations by 75%. After grinding with 40- and 25-grain abrasive wheels, high strength rolled shapes were obtained with a diameter of 30-0.20 mm and a surface finish of class 6-5 satisfying the technical specifications. (author)

  8. Nontoxic corrosion inhibitors for N80 steel in hydrochloric acid

    OpenAIRE

    M. Yadav; Debasis Behera; Usha Sharma

    2016-01-01

    The purpose of this paper is to evaluate the protective ability of 1-(2-aminoethyl)-2-oleylimidazoline (AEOI) and 1-(2-oleylamidoethyl)-2-oleylimidazoline (OAEOI) as corrosion inhibitors for N80 steel in 15% hydrochloric acid, which may find application as eco-friendly corrosion inhibitors in acidizing processes in petroleum industry. Different concentrations of synthesized inhibitors AEOI and OAEOI were added to the test solution (15% HCl) and the corrosion inhibition of N80 steel in hydroch...

  9. A simplified one-pot synthesis of 9-[(3-[{sup 18}F]Fluoro-1-hydroxy-2-propoxy)methyl]guanine([{sup 18}F]FHPG) and 9-(4-[{sup 18}F]Fluoro-3-hydroxymethylbutyl)guanine ([{sup 18}F]FHBG) for gene therapy

    Energy Technology Data Exchange (ETDEWEB)

    Shiue, Grace G.; Shiue, Chyng-Yann E-mail: Shiue@rad.upenn.edu; Lee, Roland L.; MacDonald, Douglas; Hustinx, Roland; Eck, Stephen L.; Alavi, Abass A

    2001-10-01

    9-[(3-[{sup 18}F]Fluoro-1-hydroxy-2-propoxy)methyl]guanine ([{sup 18}F]FHPG, 2) has been synthesized by nucleophilic substitution of N{sup 2}-(p-anisyldiphenylmethyl)-9-{l_brace}[1-(p-anisyldiphenylmethoxy)-3 -toluenesulfonyloxy-2-propoxy]methyl{r_brace}guanine (1) with potassium [{sup 18}F]fluoride/Kryptofix 2.2.2 followed by deprotection with 1 N HCl and purification with different methods in variable yields. When both the nucleophilic substitution and deprotection were carried out at 90 deg. C and the product was purified by HPLC (method A), the yield of compound 2 was 5-10% and the synthesis time was 90 min from EOB. However, if both the nucleophilic substitution and deprotection were carried out at 120 deg. C and the product was purified by HPLC, the yield of compound 2 decreased to 2%. When compound 2 was synthesized at 90 deg. C and purified by Silica Sep-Pak (method B), the yield increased to 10-15% and the synthesis time was 60 min from EOB. Similarly, 9-(4-[{sup 18}F]fluoro-3-hydroxymethylbutyl)guanine ([{sup 18}F]FHBG, 4) was synthesized with method A and method B in 9% and 10-15% yield, respectively, in a synthesis time of 90 and 60 min, respectively, from EOB. Compound 2 was relatively unstable in acidic medium at 120 deg. C while compound 4 was stable under the same condition. Both compound 2 and compound 4 had low lipid/water partition coefficient (0.126{+-}0.022, n=5 and 0.165{+-}0.023, n=5, respectively). Although it contains non-radioactive ganciclovir ({approx}5-30 {mu}g) as a chemical by-product, compound 2 synthesized by method B has a similar uptake in 9L glioma cells as that synthesized by method A, and is a potential tracer for imaging herpes simplex virus thymidine kinase gene expression in tumors using PET. Similarly, compound 4 synthesized by method B contains {approx}10-25 {mu}g of penciclovir as a chemical by-product. Thus, the simplified one pot synthesis (method B) is a useful method for synthesizing both compound 2 and compound 4 in

  10. Analysis of ductile-brittle transition shifts for standard and miniature bending specimens of irradiated steel

    International Nuclear Information System (INIS)

    Korshunov, M.E.; Korolev, Yu.N.; Krasikov, E.A.; Gabuev, N.N.; Tykhmeev, D.Yu.

    1996-01-01

    A study is made to reveal if there is a correlation between shifts in temperature curves obtained when testing thin plates and standard specimens on impact bending and fracture toughness. The tests were carried out using steel 25Kh3NM specimens irradiated by 6 x 10 19 cm -2 neutron fluence. A conclusion is made about the possibility to evaluate the degree of radiation-induced embrittlement of reactor steels on the basis of thin plate testing under quasistatic loads [ru

  11. Investigation into mechanical properties of joints of heterogeneous materials brazed with high-temperature solders

    International Nuclear Information System (INIS)

    Lomenko, V.I.; Merkushev, V.P.; Borodina, L.M.; Sycheva, T.S.; Tokhtina, O.A.; Frolov, N.N.

    1988-01-01

    Mechanical properties of copper joints with copper, 12Kh18M10T steel and KhD50 composite obtained by vacuum brazing by copper-titanium solder as compared with properties of joints brazed by PSr 72 and PMFOTsr 6-4-0.03 solders in hydrogen are studied. Dependences of joints strength on temperature of contact - reactive vacuum brazing are obtained. Possible applications of joints of dissimilar materials in electrovacuum devices subjected to the effect of dynamic loadings are established

  12. Study of the decarburization of 18-8 stainless steel by oxygen at low pressure

    International Nuclear Information System (INIS)

    Armand, G.; Lapujoulade, J.

    1964-01-01

    The kinetic of the decarburization of a 18-8 stainless-steel by oxygen at low pressure has been studied between 1050 and 1200 C. The measurement of the carbon content of the sample is carried out by chemical analysis. Three mechanisms take place in that decarburization: diffusion of carbon in the steel; velocity at the superficial reaction C + 1/2 O 2 ↔ CO; pumping out of CO. The second mechanism seems to govern the overall kinetic. The activation energy of the phenomenon is 108 ± 24 Kcal/mole. (authors) [fr

  13. Comparison of outcomes for veterans receiving dialysis care from VA and non-VA providers.

    Science.gov (United States)

    Wang, Virginia; Maciejewski, Matthew L; Patel, Uptal D; Stechuchak, Karen M; Hynes, Denise M; Weinberger, Morris

    2013-01-18

    Demand for dialysis treatment exceeds its supply within the Veterans Health Administration (VA), requiring VA to outsource dialysis care by purchasing private sector dialysis for veterans on a fee-for-service basis. It is unclear whether outcomes are similar for veterans receiving dialysis from VA versus non-VA providers. We assessed the extent of chronic dialysis treatment utilization and differences in all-cause hospitalizations and mortality between veterans receiving dialysis from VA versus VA-outsourced providers. We constructed a retrospective cohort of veterans in 2 VA regions who received chronic dialysis treatment financed by VA between January 2007 and December 2008. From VA administrative data, we identified veterans who received outpatient dialysis in (1) VA, (2) VA-outsourced settings, or (3) both ("dual") settings. In adjusted analyses, we used two-part and logistic regression to examine associations between dialysis setting and all-cause hospitalization and mortality one-year from veterans' baseline dialysis date. Of 1,388 veterans, 27% received dialysis exclusively in VA, 47% in VA-outsourced settings, and 25% in dual settings. Overall, half (48%) were hospitalized and 12% died. In adjusted analysis, veterans in VA-outsourced settings incurred fewer hospitalizations and shorter hospital stays than users of VA due to favorable selection. Dual-system dialysis patients had lower one-year mortality than veterans receiving VA dialysis. VA expenditures for "buying" outsourced dialysis are high and increasing relative to "making" dialysis treatment within its own system. Outcomes comparisons inform future make-or-buy decisions and suggest the need for VA to consider veterans' access to care, long-term VA savings, and optimal patient outcomes in its placement decisions for dialysis services.

  14. APT characterization of high nickel RPV steels

    International Nuclear Information System (INIS)

    Miller, M.K.; Russell, K.F

    2004-01-01

    Full text: The microstructures of several high nickel content pressure vessel steels have been characterized by atom probe tomography. The purposes of this study were to investigate the influence of high nickel levels on the response to neutron irradiation of high and low copper pressure vessel steels and to establish whether any additional phases were present after neutron irradiation. The nickel levels in these steels were at least twice that typically found in Western pressure vessel steels. Two different types of pressure vessel steels with low and high copper contents were selected for this study. The first set of alloys was low copper (∼0.05% Cu) base (15Ch2NMFAA) and weld (12Ch2N2MAA) materials used in a VVER-1000 reactor. The composition of the lower nickel VVER-1000 base material was Fe- 0.17 wt% C, 0.30% Si, 0.46% Mn, 2.2% Cr, 1.26% Ni, 0.05% Cu, 0.01% S, 0.008% P, 0.10% V and 0.50% Mo. The composition of the higher nickel VVER-1000 weld material was Fe- 0.06 wt % C, 0.33% Si, 0.80% Mn, 1.8% Cr, 1.78% Ni, 0.07% Cu, 0.009% S, 0.005% P, and 0.63% Mo. The VVER-1000 steels were irradiated in the HSSI Program's irradiation facilities at the University of Michigan, Ford Nuclear Reactor at a temperature of 288 o C for 2,137 h at an average flux of 7.08 x 10 11 cm 2 s -1 for a fluence of 5.45 x 10 18 n cm -2 (E >1 MeV) and for 5,340 h at an average flux of 4.33 x 10 11 cm -2 s -1 for a fluence of 8.32 x 10 1 28 n cm -2 (E >1 MeV). Therefore, the total fluence was 1.38 x 10 19 n cm -2 (E >1 MeV). The second type of pressure vessel steel was a high copper (0.20% Cu) weld from the Palisades reactor. The average composition of the Palisades weld was Fe- 0.11 wt% C, 0.18% Si, 1.27% Mn, 0.04% Cr, 1.20% Ni, 0.20% Cu, 0.017% S, 0.014% P, 0.003% V and 0.55% Mn. The Palisades weld, designated weldment 'B' from weld heat 34B009, was irradiated at a temperature of 288 o C and a flux of ∼7 x 10 11 cm -2 s -1 to a fast fluence of 1.4 x 10 19 n cm -2 (E >1 MeV). These three

  15. Synthesis procedure for routine production of 2-[{sup 18}F]fluoro-3-(2(S)-azetidinylmethoxy)pyridine (2-[{sup 18}F]F-A-85380)

    Energy Technology Data Exchange (ETDEWEB)

    Schildan, Andreas [Department of Nuclear Medicine, University of Leipzig, 04103 Leipzig (Germany)], E-mail: andreas.schildan@medizin.uni-leipzig.de; Patt, Marianne; Sabri, Osama [Department of Nuclear Medicine, University of Leipzig, 04103 Leipzig (Germany)

    2007-11-15

    2-[{sup 18}F]Fluoro-3-(2(S)-azetidinylmethoxy)pyridine (2-[{sup 18}F]F-A-85380) was among the first subtype selective radioligands to visualise the in vivo distribution of {alpha}4{beta}2-containing neuronal nicotinic acetylcholine receptors (nAChRs) in human brain. We developed a one-pot synthesis for the preparation of 2-[{sup 18}F]F-A-85380 in a commercially available TRACERlab FX{sub F-N} synthesis module. The synthesis comprises a nucleophilic substitution followed by hydrolysis of a t-butyloxycarbonyl (BOC)-protected intermediate. After formulation for intravenous application up to 20 GBq 2-[{sup 18}F]F-A-85380 were produced from a starting activity of 100 GBq [{sup 18}F]fluoride in 60 min with a specific activity of about 4.10{sup 5} GBq/mmol and a mean radiochemical purity of more than 99%.

  16. VA office of inspector general releases scathing report of Phoenix VA

    Directory of Open Access Journals (Sweden)

    Robbins RA

    2014-08-01

    Full Text Available No abstract available. Article truncated at 150 words. The long-awaited Office of Inspector General’s (OIG report on the Phoenix VA Health Care System (PVAHCS was released on August 27, 2014 (1. The report was scathing in its evaluation of VA practices and leadership. Five questions were investigated: 1.Were there clinically significant delays in care? 2. Did PVAHCS omit the names of veterans waiting for care from its Electronic Wait List (EWL? 3. Were PVAHCS personnel not following established scheduling procedures? 4. Did the PVAHCS culture emphasize goals at the expense of patient care? 5. Are scheduling deficiencies systemic throughout the VA? In each case, the OIG found that the allegations were true. Despite initial denials, the OIG report showed that former PVAHCS director Sharon Helman, associate director Lance Robinson, hospital administration director Brad Curry, chief of staff Darren Deering and other senior executives were aware of delays in care and unofficial wait lists. Perhaps most disturbing is ...

  17. An improved synthesis of 4-[{sup 18}F]-ADAM, a potent serotonin transporter imaging agent

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Y.-Y. [PET Center, Department of Nuclear Medicine, Tri-Service General Hospital 325 Section 2, Cheng-Kung Road, Neihu 114, Taipei, Taiwan (China); Department of Biomedical Engineering and Environmental Sciences, National Thising Hua University, 101, Section 2, Kuang-Fu Road, Hsinchu 30013, Taiwan (China); Huang, W.-S. [PET Center, Department of Nuclear Medicine, Tri-Service General Hospital 325 Section 2, Cheng-Kung Road, Neihu 114, Taipei, Taiwan (China); Chu, T.-C. [Department of Biomedical Engineering and Environmental Sciences, National Thising Hua University, 101, Section 2, Kuang-Fu Road, Hsinchu 30013, Taiwan (China); Shiue, C.-Y. [PET Center, Department of Nuclear Medicine, Tri-Service General Hospital 325 Section 2, Cheng-Kung Road, Neihu 114, Taipei, Taiwan (China)], E-mail: shiue@ndmctsgh.edu.tw

    2009-06-15

    An improved synthesis of N,N-dimethyl-2-(2-amino-4-[{sup 18}F]fluorophenylthio)benzylamine (4-[{sup 18}F]-ADAM, 2) as a potent serotonin transporter (SERT) imaging agent is described. Molecular orbital (MO) calculation predicts that N,N-dimethyl-2- (2-nitro-4-trimethylammoniumtrifluoromethanesulfonylphenylthio)benzamide (8) is probably a better precursor than N,N-dimethyl-2-(2,4-dinitrophenylthio)benzylamine (1) for preparing 2. Radioligand 2 was synthesized by the reaction of either precursor 1 or precursor 8 with K[{sup 18}F]/K{sub 2.2.2} at 120 deg. C followed by reduction with BH{sub 3} at 80 deg. C. The radiochemical yield (EOB) of 2 synthesized from precursor 1 and 8 was 5.7{+-}2.4% (n=6) and 14.8{+-}4.0% (n=5), respectively, in a synthesis time of 120 min from EOB. The specific activity of 2 was 3 Ci/{mu}mol or 111 GBq/{mu}mol (EOB). Thus, this new synthetic method has significantly improved the radiochemical yield of 4-[{sup 18}F]-ADAM and makes this radioligand more accessible to PET Centers without a cyclotron.

  18. In vivo evaluation in rats of [18F]1-(2-fluoroethyl)-4-[(4-cyanophenoxy)methyl]piperidine as a potential radiotracer for PET assessment of CNS sigma-1 receptors

    International Nuclear Information System (INIS)

    Waterhouse, Rikki N.; Chang, Raymond C.; Zhao, Jun; Carambot, Patty E.

    2006-01-01

    Introduction: Sigma-1 receptors are expressed throughout the mammalian central nervous system (CNS) and are implicated in several psychiatric disorders, including schizophrenia and depression. We have recently evaluated the high-affinity (K D =0.5±0.2 nM, log P=2.9) sigma-1 receptor radiotracer [ 18 F]1-(3-fluoropropyl)-4-(4-cyanophenoxymethyl)piperidine, [ 18 F]FPS, in humans. In contrast to appropriate kinetics exhibited in baboon brain, in the human CNS, [ 18 F]FPS does not reach pseudoequilibrium by 4 h, supporting the development of a lower-affinity tracer [Waterhouse RN, Nobler MS, Chang RC, Zhou Y, Morales O, Kuwabara H, et al. First evaluation of the sigma-1 receptor radioligand [ 18 F]1-3-fluoropropyl-4-((4-cyanophenoxy)-methyl)piperidine ([ 18 F]FPS) in healthy humans. Neuroreceptor Mapping 2004, July 15-18th, Vancouver, BC Canada 2004]. We describe herein the in vivo evaluation in rats of [ 18 F]1-(2-fluoroethyl)-4-[(4-cyanophenoxy)methyl]piperidine ([ 18 F]SFE) (K D =5 nM, log P=2.4), a structurally similar, lower-affinity sigma-1 receptor radioligand. Methods: [ 18 F]SFE was synthesized (n=4) as previously described in good yield (54±6% EOB), high specific activity (2.1±0.6 Ci/μmol EOS) and radiochemical purity (98±1%) and evaluated in awake adult male rats. Results: Similar to [ 18 F]FPS, regional brain radioactivity concentrations [percentage of injected dose per gram of tissue (%ID/g), 15 min] for [ 18 F]SFE were highest in occipital cortex (1.86±0.06 %ID/g) and frontal cortex (1.76±0.38 %ID/g), and lowest in the hippocampus (1.01±0.02%ID/g). Unlike [ 18 F]FPS, [ 18 F]SFE cleared from the brain with ∼40% reduction in peak activity over a 90-min period. Metabolite analysis (1 h) revealed that [ 18 F]SFE was largely intact in the brain. Blocking studies showed a large degree (>80%) of saturable binding for [ 18 F]SFE in discrete brain regions. Conclusions: We conclude that [ 18 F]SFE exhibits excellent characteristics in vivo and may provide

  19. No-carrier-added (NCA) N-(3-[18F]fluoropropyl)-N-norbuprenorphine and N-(3-[18F]fluoropropyl)-N-nordiprenorphine -synthesis, anatomical distribution in mice and rats, and tomographic studies in a baboon

    International Nuclear Information System (INIS)

    Lanqin Bai; Renrui Teng; Chyngyann Shiue; Wolf, A.P.; Dewey, S.L.; Holland, M.J.; Simon, E.J.

    1990-01-01

    N-(3-Fluoropropyl)-N-norbuprenorphine (3a) and N-(3-fluoropropyl)-N-nordiprenorphine (4a) were synthesized by N-alkylation of norbuprenorphine (1) and nordiprenorphine (2) with 1-bromo-3-fluoropropane. The corresponding no-carrier-added (NCA) N-(3-[ 18 F]fluoropropyl)-N-norbuprenorphine (3b) and N-(3-[ 18 F]fluoropropyl)-N-nordiprenorphine (4b) were synthesized by N-alkylation of 1 and 2 with NCA 1-[ 18 F]fluoro-3-iodopropane. In vitro studies indicate that in the absence of sodium chloride, compounds 3a, 4a, N-propyl-N-norbuprenorphine (5), buprenorphine and diprenorphine are reasonably comparable in binding affinity for opioid receptors. In the presence of 100 mM sodium chloride, however, compounds 3a, 4a and 5, are clearly less potent than buprenorphine and diprenorphine. The anatomical distribution study of compound 3b in mice shows radioactivity accumulating in bone. Rat studies of both compounds 3b and 4b indicate the specific distribution of these two radioligands within certain cortical and subcortical regions of rat brain. However, the absolute uptake of compound 4b in rat brain was only half that of compound 3b. PET studies of 3b in a baboon revealed specific binding of compound 3b in striatum and cerebellum. At 1 h after injection, ratios of specific/non-specific binding of 3b in striatum and cerebellum of a baboon were 1.9 and 1.7 respectively. (author)

  20. Synthesis of 4-([{sup 18}F]fluoromethyl)-2-chlorophenylisothiocyanate: a novel bifunctional {sup 18}F-labelling agent

    Energy Technology Data Exchange (ETDEWEB)

    Wuest, F.; Mueller, M.; Bergmann, R. [Inst. fuer Bioanorganische und Radiopharmazeutische Chemie, FZ-Rossendorf e.V., Dresden (Germany)

    2004-07-01

    The one-step radiosynthesis of 4-([{sup 18}F]fluoromethyl)-2-chlorophenylisothiocyanate {sup 18}F-7 as a novel bifunctional {sup 18}F-labelling agent is described. Optimised reaction conditions in a remotely controlled synthesis module gave isothiocyanate {sup 18}F-7 in radiochemical yields of 45% (decay-corrected) within 40 min and high radiochemical purity of > 95% after solid-phase-extraction. Coupling of compound {sup 18}F-7 with the primary amine benzylamine as a model reaction afforded the corresponding ((4-[{sup 18}F]fluoromethyl)-2-chloro-phenyl)-benzyl thiourea {sup 18}F-8 in a high radiochemical yield of > 90%. Stability studies of thiourea {sup 18}F-8 in terms of radiodefluorination showed appreciable buffer stability at pH 7.4, whereas significant radiodefluorination was observed when {sup 18}F-8 was incubated in buffers at pH 3.6 and pH 9.4. Preliminary dynamic PET studies with thiourea {sup 18}F-8 in male Wistar rats showed high bone accumulation, indicative of high in vivo radiodefluorination. (orig.)

  1. Susceptibility of 2 1/4 Cr-1Mo steel to liquid metal induced embrittlement by lithium-lead solutions

    International Nuclear Information System (INIS)

    Eberhard, B.A.; Edwards, G.R.

    1984-08-01

    An investigation has been conducted on the liquid metal induced embrittlement susceptibility of 2 1/4Cr-1Mo steel exposed to lithium and 1a/o lead-lithium at temperatures between 190 0 C and 525 0 C. This research was part of an ongoing effort to evaluate the compatibility of liquid lithium solutions with potential fusion reactor containment materials. Of particular interest was the microstructure present in a weld heat-affected zone, a microstructure known to be highly susceptible to corrosive attack by liquid lead-lithium solutions. Embrittlement susceptibility was determined by conducting tension tests on 2 1/4Cr-1Mo steel exposed to an inert environment as well as to a lead-lithium liquid and observing the change in tensile behavior. The 2 1/4Cr-1Mo steel was also given a base plate heat treatment to observe its embrittlement susceptibility to 1a/o lead-lithium. The base plate microstructure was severely embrittled at temperatures less than 500 0 C. Tempering the base plate was effective in restoring adequate ductility to the steel

  2. Comparison of outcomes for veterans receiving dialysis care from VA and non-VA providers

    Directory of Open Access Journals (Sweden)

    Wang Virginia

    2013-01-01

    Full Text Available Abstract Background Demand for dialysis treatment exceeds its supply within the Veterans Health Administration (VA, requiring VA to outsource dialysis care by purchasing private sector dialysis for veterans on a fee-for-service basis. It is unclear whether outcomes are similar for veterans receiving dialysis from VA versus non-VA providers. We assessed the extent of chronic dialysis treatment utilization and differences in all-cause hospitalizations and mortality between veterans receiving dialysis from VA versus VA-outsourced providers. Methods We constructed a retrospective cohort of veterans in 2 VA regions who received chronic dialysis treatment financed by VA between January 2007 and December 2008. From VA administrative data, we identified veterans who received outpatient dialysis in (1 VA, (2 VA-outsourced settings, or (3 both (“dual” settings. In adjusted analyses, we used two-part and logistic regression to examine associations between dialysis setting and all-cause hospitalization and mortality one-year from veterans’ baseline dialysis date. Results Of 1,388 veterans, 27% received dialysis exclusively in VA, 47% in VA-outsourced settings, and 25% in dual settings. Overall, half (48% were hospitalized and 12% died. In adjusted analysis, veterans in VA-outsourced settings incurred fewer hospitalizations and shorter hospital stays than users of VA due to favorable selection. Dual-system dialysis patients had lower one-year mortality than veterans receiving VA dialysis. Conclusions VA expenditures for “buying” outsourced dialysis are high and increasing relative to “making” dialysis treatment within its own system. Outcomes comparisons inform future make-or-buy decisions and suggest the need for VA to consider veterans’ access to care, long-term VA savings, and optimal patient outcomes in its placement decisions for dialysis services.

  3. Nivel de corte de los ELISAs para cuantificación de anticuerpos inducidos por la vacuna antimeningocócica VA-MENGOC-BC

    Directory of Open Access Journals (Sweden)

    Rolando Ochoa

    2001-06-01

    Full Text Available Para medir el grado de protección inducido por vacunas antimeningocócicas se ha establecido el Ensayo Bactericida en Suero (EBS y se perfeccionan otros ensayos inmunobiológicos, sin embargo, es necesario contar con pruebas sencillas como el ELISA, capaz de evaluar un gran número de muestras. Se estimó el nivel de corte de los ELISAs para la cuantificación de IgG humana contra los antígenos de VA-MENGOC-BC, vacuna antimeningocócica compuesta por vesículas proteicas de membrana externa de meningococo B y polisacárido capsular de meningococo C, con respecto a un panel de muestras de suero de lactantes, caracterizado por Ensayo Bactericida en Sangre Total (EBST. Los valores correspondientes a la máxima sensibilidad y especificidad fueron respectivamente; 2 μg/mL y 12 μg/mL para antipolisacárido C, y 1000 U/mL y 7000 U/mL para antiproteínas de membrana externa. La mayor coincidencia se obtuvo con 6 μg/mL y 2500 U/mL. Se evaluó otro panel de muestras de suero de adolescentes entre 14 y 18 años, por ELISA y EBS para Neisseria meningitidis serogrupos B y C, alcanzándose una buena concordancia. Doce años después de la inmunización con VA-MENGOC-BC persiste una importante concentración de anticuerpos contra los antígenos vacunales en los sueros estudiados.

  4. Corrosion inhibition performance of 2,5-bis(4-dimethylaminophenyl)-1,3,4-oxadiazole for carbon steel in HCl solution: Gravimetric, electrochemical and XPS studies

    Energy Technology Data Exchange (ETDEWEB)

    Bouanis, M.; Tourabi, M.; Nyassi, A. [Laboratoire de Catalyse et de Corrosion des Matériaux (LCCM), Faculté des Sciences, Université Chouaib Doukkali, B.P. 20, M-24000 El Jadida (Morocco); Zarrouk, A. [LCAE-URAC 18, Faculty of Science, First Mohammed University, PO Box 717, M-60 000 Oujda (Morocco); Jama, C. [UMET-ISP, CNRS UMR 8207, ENSCL, Université Lille Nord de France, CS 90108, F-59652 Villeneuve d' Ascq Cedex (France); Bentiss, F., E-mail: fbentiss@gmail.com [Laboratoire de Catalyse et de Corrosion des Matériaux (LCCM), Faculté des Sciences, Université Chouaib Doukkali, B.P. 20, M-24000 El Jadida (Morocco); UMET-ISP, CNRS UMR 8207, ENSCL, Université Lille Nord de France, CS 90108, F-59652 Villeneuve d' Ascq Cedex (France)

    2016-12-15

    Highlights: • 2,5-Bis(4-dimethylaminophenyl)-1,3,4-oxadiazole is good corrosion inhibitor for carbon steel in 1 M HCl. • XPS analysis has provided the composition of adsorbed protective layer on the steel surface. • The adsorption of the investigated 1,3,4-oxadiazole is mainly due to chemisorption. - Abstract: Corrosion inhibition of carbon steel in normal hydrochloric acid solution at 30 °C by 2,5-bis(4-dimethylaminophenyl)-1,3,4-oxadiazole (DAPO) has been studied by weight loss measurements and electrochemical techniques (polarization and AC impedance). The experimental results showed that DAPO acted as an efficient inhibitor against the carbon steel corrosion in 1 M HCl, and its inhibition efficiency increased with the inhibitor concentration reaching a value up to 93% at 1 mM. Polarization studies showed that the DAPO was a mixed-type inhibitor. The adsorption of this 1,3,4-oxadiazole derivative on the carbon steel surface in 1 M HCl solution followed the Langmuir adsorption isotherm and the corresponding value of the standard Gibbs free energy of adsorption (ΔG°{sub ads}) is associated to a chemisorption mechanism. Scanning Electron Microscopy (SEM) and X-Ray Photoelectron Spectroscopy (XPS) analyses were carried out to characterize the chemical composition of the inhibitive film formed on the steel surface. The surfaces studies showed that the inhibitive layer is composed of an iron oxide/hydroxide mixture where DAPO molecules are incorporated. The cytotoxicity of DAPO was also determined using cell culture system.

  5. Caustic cracking of 2 1/4 CrMo steel

    International Nuclear Information System (INIS)

    Cowen, H.C.; Thorley, A.W.

    1983-12-01

    Stress corrosion cracking tests performed on the 21/4 Cr Mo ferritic steel are described. The principal environments studied were strong, aqueous caustic soda, molten anhydrous caustic soda, and caustic soda with an addition of sodium. Emphasis has been placed on material in the quenched-hardened condition. (author)

  6. Boron content effect on the high-temperature plasticity of corrosion resistant low-carbon austenite type steels

    International Nuclear Information System (INIS)

    Gol'dshtejn, Ya.E.; Shmatko, M.N.; Chuvatina, S.N.

    1976-01-01

    With the concept that the state of grain and subgrain boundaries influences the hot plasticity of corrosion resistant steel as a starting point, the study was undertaken of the effect of boron microalloying up on the intergranular strength and of the action boron exerts upon the distribution (redistribution) of other phases present in austenitic 03Kh16N14M3 steels. An electron microscope study of the composition of redundant phases and that of the fine structure of steel have shown the effect of small additions of boron upon the hot plasticity of steel to be linked directly to its influence upon austenite disintegration and the precipitation along the boundaries of crystals of redundant phases in the course of hot plastic deformation. The action of boron upon the process plasticity of steel depends on the temperature and the rate of deformation which govern the kinetics of the precipitation of the redundant phases

  7. Crystal structure of poly[[μ-1,1′-(butane-1,4-diylbis(1H-benzimidazole-κ2N3:N3′]{μ-4,4′-[1,4-phenylenebis(oxy]dibenzoato-κ4O,O′:O′′,O′′′}cobalt(II

    Directory of Open Access Journals (Sweden)

    Chen Xie

    2015-06-01

    Full Text Available In the title compound, [Co(C20H12O6(C18H18N4]n, the CoII atom, located on a twofold rotation axis, is hexacoordinated to four O from two bis-bidentate 4,4′-[phenylenebis(oxy]dibenzoate (L ligands and two N atoms from two 1,1′-(butane-1,4-diylbis(1H-benzimidazole (bbbm ligands, forming a distorted octahedral cis-N2O4 coordination environment. Polymeric zigzag chains along [102] are built up by the bridging L ligands. These chains are additionally connected by the bbbm ligands to produce a two-dimensional coordination polymer parallel too (010.

  8. New method for NPP sodium coolant pipeline austenization

    International Nuclear Information System (INIS)

    Malashonok, V.A.; Rotshtejn, A.V.; Gotshalk, A.L.; Miryushchenko, E.F.

    1980-01-01

    Heat treatment technology is considered for pipelines intended for the NPP cooling systems employing sodium coolant. Various techniques are discussed which are used for protecting the pipeline internal surfaces against oxidation in the process of heat treatment. It is noted that the austenite formation of welded joints of steel 12Kh18N9 and steel Kh16N11M3 at temperatures of 1050 and 1100 deg C releases welding-induced stresses and reduces a possibility of local damages. Evacuation down to 1 mm Hg appears to be the most rational protective technique. The considered procedure of the pipeline heat treatment has been utilized for mounting the equipment of the BN-600 reactor at the Beloyarskaya NPP. The economic gain resulting from the use of the procedure, owing to decrease in argon consumption and reduction of labour input, makes up 150 000 roubles

  9. Crystal structure of fac-[2-(4-methyl-5-phenylpyridin-2-ylphenyl-κ2C1,N]bis[2-(pyridin-2-ylphenyl-κ2C1,N]iridium(III

    Directory of Open Access Journals (Sweden)

    Chi-Heon Lee

    2016-12-01

    Full Text Available In the title compound, [Ir(C11H8N2(C18H14N], the IrIII ion adopts a distorted octahedral coordination environment defined by three C,N-chelating ligands, one stemming from a 2-(4-phenyl-5-methylpyridin-2-ylphenyl ligand and two from 2-(pyridin-2-ylphenyl ligands, arranged in a facial manner. The IrIII ion lies almost in the equatorial plane [deviation = 0.0069 (15 Å]. In the crystal, intermolecular π–π stacking interactions, as well as intermolecular C—H...π interactions, are present, leading to a three-dimensional network.

  10. Generation of novel metabolites of dietary linoleic acid (18:2n6) by guinea pig epidermis

    Energy Technology Data Exchange (ETDEWEB)

    Chapkin, R.S.; Ziboh, V.A.

    1986-03-05

    Although the authors have demonstrated the inability of rat and guinea pig (GP) skin enzyme preparations to desaturate 18:2n6 into gammalinolenic acid (18:3n6) using an in vitro microsomal system, the fate of this dietary essential fatty acid in the GP epidermis is unknown. To explore the fate of 18:2n6, intact tissue slices from GP epidermis were incubated with (1-/sup 14/C)18:2n6. After incubation, the extracted lipids were transesterified using methanolic-HCL. The fatty acid methyl esters were analyzed using a combination of (i) argentation TLC, scanned using a proportional TLC radioscanner, and (ii) reverse phase HPLC, equipped with a flow through radioscanner. The results indicate that the intact epidermis metabolized /sup 14/C-18:2n6 to a group of novel products more polar than 18:2n6. In subsequent experiments, /sup 14/C-18:2n6 was either incubated with the 800 xg supernatant, the 105,000 xg pellet or supernatant from GP epidermis. Metabolism of 18:2n6 by the high speed supernatant resulted in the generation of polar products with chromatographic properties of not greater than 2 double bonds. These results indicate that although the GP epidermis lacks the capacity to desaturate 18:2n6 to 18:3n6, it can convert dietary 18:2n6 into a group of novel polar metabolites via a cytosolic mediated process. The function of these metabolites in the GP integumentary system remains to be determined.

  11. Generation of novel metabolites of dietary linoleic acid (18:2n6) by guinea pig epidermis

    International Nuclear Information System (INIS)

    Chapkin, R.S.; Ziboh, V.A.

    1986-01-01

    Although the authors have demonstrated the inability of rat and guinea pig (GP) skin enzyme preparations to desaturate 18:2n6 into gammalinolenic acid (18:3n6) using an in vitro microsomal system, the fate of this dietary essential fatty acid in the GP epidermis is unknown. To explore the fate of 18:2n6, intact tissue slices from GP epidermis were incubated with [1- 14 C]18:2n6. After incubation, the extracted lipids were transesterified using methanolic-HCL. The fatty acid methyl esters were analyzed using a combination of (i) argentation TLC, scanned using a proportional TLC radioscanner, and (ii) reverse phase HPLC, equipped with a flow through radioscanner. The results indicate that the intact epidermis metabolized 14 C-18:2n6 to a group of novel products more polar than 18:2n6. In subsequent experiments, 14 C-18:2n6 was either incubated with the 800 xg supernatant, the 105,000 xg pellet or supernatant from GP epidermis. Metabolism of 18:2n6 by the high speed supernatant resulted in the generation of polar products with chromatographic properties of not greater than 2 double bonds. These results indicate that although the GP epidermis lacks the capacity to desaturate 18:2n6 to 18:3n6, it can convert dietary 18:2n6 into a group of novel polar metabolites via a cytosolic mediated process. The function of these metabolites in the GP integumentary system remains to be determined

  12. Organotin(IV Derivatives of 2-Acetylpyridine-N(4-Phenylthiosemicarbazone, HAP4P, and 2-Hydroxyacetophenone-N(4-Phenylthiosemicarbazone, H2DAP4P: Crystal and Molecular Structure of [SnMe2(DAP4P] and [SnBu2(DAP4P

    Directory of Open Access Journals (Sweden)

    Sousa Gerimário F. de

    2001-01-01

    Full Text Available The reactions of 2-acetylpyridine-N(4-phenylthiosemicarbazone, HAP4P, and 2-hydroxyacetophenone-N(4-phenylthiosemicarbazone, H2DAP4P, with R4-mSnXm (m = 2, 3; R = Me, nBu, Ph and X = Cl, Br led to the formation of hexa- and penta-coordinated organotin(IV complexes, which were studied by microanalysis, IR, ¹H-NMR and Mössbauer spectroscopies. The molecular structures of [SnMe2(DAP4P] and [Sn nBu2(DAP4P] were determined by single-crystal X-ray diffraction studies. In the compounds [SnClMe2(AP4P] and [SnBrMe2(AP4P], the deprotonated ligand AP4P- is N,N,S-bonded to the Sn(IV atoms, which exhibit strongly distorted octahedral coordination. The structures of [SnMe2(DAP4P] and [Sn nBu2(DAP4P] revealed that the DAP4P2- anion acts as a O,N,S-tridentate ligand. In these cases, the Sn(IV atoms adopt a strongly distorted trigonal bipyramidal configuration where the azomethine N and the two C atoms are on the equatorial plane while the O and the S atoms occupy the axial positions.

  13. Corrosion studies on casing steel in CO2 storage environments

    NARCIS (Netherlands)

    Zhang, X.; Zevenbergen, J.F.; Benedictus, T.

    2013-01-01

    The corrosion behavior of casing steel N80 in brine plus CO2 was studied in autoclave to simulate the CO2 storage environment. The brine solution used in the study contained 130 g/l NaCl, 22.2 g/l CaCl2 and 4 g/l MgCl2. The CO2 was charged in the autoclave at different pressures (60, 80 and 100 bar)

  14. Crystal structures of N2,N3,N5,N6-tetrakis(pyridin-2-ylmethylpyrazine-2,3,5,6-tetracarboxamide and N2,N3,N5,N6-tetrakis(pyridin-4-ylmethylpyrazine-2,3,5,6-tetracarboxamide

    Directory of Open Access Journals (Sweden)

    Dilovan S. Cati

    2017-02-01

    Full Text Available The title compounds, C32H28N10O4· unknown solvent, (I, and C32H28N10O4, (II, are pyrazine-2,3,5,6-tetracarboxamide derivatives. In (I, the substituents are (pyridin-2-ylmethylcarboxamide, while in (II, the substituents are (pyridin-4-ylmethylcarboxamide. Both compounds crystallize in the monoclinic space group P21/n, with Z′ = 1 for (I, and Z′ = 0.5 for (II. The whole molecule of (II is generated by inversion symmetry, the pyrazine ring being situated about a center of inversion. In (I, the four pyridine rings are inclined to the pyrazine ring by 83.9 (2, 82.16 (18, 82.73 (19 and 17.65 (19°. This last dihedral angle involves a pyridine ring that is linked to the adjacent carboxamide O atom by an intramolecular C—H...O hydrogen bond. In compound (II, the unique pyridine rings are inclined to the pyrazine ring by 33.3 (3 and 81.71 (10°. There are two symmetrical intramolecular C—H...O hydrogen bonds present in (II. In the crystal of (I, molecules are linked by N—H...O and N—H...N hydrogen bonds, forming layers parallel to (10-1. The layers are linked by C—H...O and C—H...N hydrogen bonds, forming a three-dimensional framework. In the crystal of (II, molecules are linked by N—H...N hydrogen bonds, forming chains propagating along the [010] direction. The chains are linked by a weaker N—H...N hydrogen bond, forming layers parallel to the (101 plane, which are in turn linked by C—H...O hydrogen bonds, forming a three-dimensional structure. In the crystal of compound (I, a region of disordered electron density was treated with the SQUEEZE routine in PLATON [Spek (2015. Acta Cryst. C71, 9–18]. Their contribution was not taken into account during refinement. In compound (II, one of the pyridine rings is positionally disordered, and the refined occupancy ratio for the disordered Car—Car—Npy atoms is 0.58 (3:0.42 (3.

  15. Crystal structure of an unknown solvate of bis(tetra-n-butylammonium [N,N′-(4-trifluoromethyl-1,2-phenylenebis(oxamato-κ4O,N,N′,O′]nickelate(II

    Directory of Open Access Journals (Sweden)

    François Eya'ane Meva

    2015-06-01

    Full Text Available In the title compound, [N(C4H94]2[Ni(C11H3F3N2O6] or [N(n-Bu4]2[Ni(topbo] [n-Bu = n-butyl and topbo = 4-trifluoromethyl-1,2-phenylenebis(oxamate], the Ni2+ cation is coordinated by two deprotonated amido N atoms and two carboxylate O atoms, setting up a slightly distorted square-planar coordination environment. The [Ni(topbo]2− anion lies on a twofold rotation axis. Due to an incompatibility with the point-group symmetry of the complete molecule, orientational disorder of the CF3 group is observed. The tetrahedral ammonium cations and the anion are linked by weak intermolecular C—H...O and C—H...F hydrogen-bonding interactions into a three-dimensional network. A region of electron density was treated with the SQUEEZE procedure in PLATON [Spek (2015. Acta Cryst. C71, 9–18] following unsuccessful attempts to model it as plausible solvent molecule(s. The given chemical formula and other crystal data do not take into account the unknown solvent molecule.

  16. Synthesis and labeling 5'-O-(4-4'-dimetoxytrityl) -2,3-anhidrothymidine for preparation of radiopharmaceutical [18F]FLT

    International Nuclear Information System (INIS)

    Purwoko; Maskur; Chaeruman; Sugiarto, Yono

    2013-01-01

    It is has been known that the compound of 3'-deoxy-3,-( 18 F] Fluorothymidine or ( 18 F] FLT is a thymidine derivative radiopharmaceutical used for cancer detection based on DNA metabolism. Synthesis and labeling of 5'-0-(4,4 '-dimetoxytrityl) -2,3' anhidrothymidine precursor for preparation of the radiopharmaceutical [ 18 F]FL T was carried out. The precursor was synthesized in similar manner and procedure literature and it have been obtained a crystalline product with total yield of 32,4 %. The chemical purity of the product which determined by HPLC was found to be more than 95%. Characterization of the product was done by observing the results of the LC / MS and 1 H-NMR test, the resulted data were found to be very closed to those reported in the literature. Labeling of the precursor was done by nucleophilic fluorination reactions using 18 Fluoride at 160 °C for 15 minutes with kryptofix 2.2.2 catalyst followed hydrolysis using HCI at 100 °C for 10 minutes and then neutralized with NaOH. Purification [ 18 F]FLT was performed by single cartridge Alumina-N as a substitute HPLC methods. The results have been obtained a label compound [ 18 F]FLT with high purity as a bulk for preparation of the radiopharmaceutical [ 18 F]FLT. The label compound of [ 18 F]FLT undergone a quality test which included a clarity, pH and a radiochemical purity. The results of quality control on four batches of [ 18 F]FLT showed that these products were colorless clear solution with pH between 6.0-7.5, and radiochemical purity 97.93 ± 1,48% and showed that the label compounds have been obtained [ 18 F]FLT-free particles form a clear solution with a pH between 6,0 - 7,5, radiochemical purity of 97.93 ± 1,48 %, radiochemical yields 8.18 ± 1.54% (decay uncorrected) and processing time 73 ± 4 minutes. (author)

  17. A detailed study of the dehydration process in synthetic strelkinite, Na[(UO2)(VO4)] . nH2O (n = 0, 1, 2)

    International Nuclear Information System (INIS)

    Suleimanov, Evgeny V.; Somov, Nikolay V.; Chuprunov, Evgeny V.; Mayatskikh, Ekaterina F.; Depmeier, Wulf

    2012-01-01

    Synthetic strelkinite Na[(UO 2 )(VO 4 )] . nH 2 O (n = 0, 1, 2) was systematically investigated by single crystal X-ray diffraction and thermoanalytical methods. The anhydrous form and two hydrates were isolated as single crystals and the structures of these phases solved: Na[(UO 2 )(VO 4 )], monoclinic, P2 1 /c, a = 6.0205(1) Aa, b = 8.3365(1) Aa, c = 10.4164(2) Aa, β = 100.466(2) , V = 514.10(1) Aa 3 , R 1 = 0.0337; Na[(UO 2 )(VO 4 )] . H 2 O, monoclinic, P2 1 /c, a = 7.722(2) Aa, b = 8.512(1) Aa, c = 10.480(4) Aa, β = 113.18(3) , V = 633.3(3) Aa 3 , R 1 = 0.1658; Na[(UO 2 )(VO 4 )] . 2 H 2 O, monoclinic, P2 1 /n, a = 16.2399(5) Aa, b = 8.2844(2) Aa, c = 10.5011(2) Aa, β = 97.644(2) , V = 1400.24(6) Aa 3 , R 1 = 0.0776. A possible mechanism of the structural transformation processes during dehydration is proposed based on the structures of the anhydrous phase and the hydrates. (orig.)

  18. Comparison of Steam Oxidation of 18%Cr Steels from Various Power Plants

    DEFF Research Database (Denmark)

    Montgomery, Melanie; Hald, John

    2015-01-01

    Lean austenitic steels such as the 18%Cr TP347H have been utilized in many power plants in Denmark. Steam oxidation has been investigated for both coarse-grained and fine-grained versions of TP347H. Oxidation for coarsegrained steels follows a parabolic rate however this is not always the case fo...

  19. No-carrier-added (NCA) N-(3-( sup 18 F)fluoropropyl)-N-norbuprenorphine and N-(3-( sup 18 F)fluoropropyl)-N-nordiprenorphine -synthesis, anatomical distribution in mice and rats, and tomographic studies in a baboon

    Energy Technology Data Exchange (ETDEWEB)

    Bai, Lanqin; Teng, Renrui; Shiue, Chyngyann; Wolf, A P; Dewey, S L [Brookhaven National Lab., Upton, NY (USA); Holland, M J; Simon, E J [New York Univ., NY (USA). Medical Center

    1990-01-01

    N-(3-Fluoropropyl)-N-norbuprenorphine (3a) and N-(3-fluoropropyl)-N-nordiprenorphine (4a) were synthesized by N-alkylation of norbuprenorphine (1) and nordiprenorphine (2) with 1-bromo-3-fluoropropane. The corresponding no-carrier-added (NCA) N-(3-({sup 18}F)fluoropropyl)-N-norbuprenorphine (3b) and N-(3-({sup 18}F)fluoropropyl)-N-nordiprenorphine (4b) were synthesized by N-alkylation of 1 and 2 with NCA 1-({sup 18}F)fluoro-3-iodopropane. In vitro studies indicate that in the absence of sodium chloride, compounds 3a, 4a, N-propyl-N-norbuprenorphine (5), buprenorphine and diprenorphine are reasonably comparable in binding affinity for opioid receptors. In the presence of 100 mM sodium chloride, however, compounds 3a, 4a and 5, are clearly less potent than buprenorphine and diprenorphine. The anatomical distribution study of compound 3b in mice shows radioactivity accumulating in bone. Rat studies of both compounds 3b and 4b indicate the specific distribution of these two radioligands within certain cortical and subcortical regions of rat brain. However, the absolute uptake of compound 4b in rat brain was only half that of compound 3b. PET studies of 3b in a baboon revealed specific binding of compound 3b in striatum and cerebellum. At 1 h after injection, ratios of specific/non-specific binding of 3b in striatum and cerebellum of a baboon were 1.9 and 1.7 respectively. (author).

  20. Computer Science and Statistics. Proceedings of the Symposium on the Interface (18th) Held on March 19-21, 1986 in Fort Collins, Colorado.

    Science.gov (United States)

    1987-08-26

    MACROS scaled $sub tile probit cycle deviance df $mac fv 4i 114~.7 18 $switch %s mext $calc lp-u*%lp :y~r/n $caic %3=1 :phez%np(lp)gu: $yvar y dphe :(1...z1/((1-%pe(a))* dphe ) I HAVE CONTROL OVER %pe ORDER $endm I IT WOULD NOT BE NEEDED WERE $a vs Scale %va_-f’v*(1-%fv)/n I ’a’ NOT A FACTOR. $calc %va

  1. A study on martensitic structure in Fe-4Cr-0.4C steel

    International Nuclear Information System (INIS)

    Won, S.B.

    1980-01-01

    Morphology, dependence of prior austenite grain size and packet size upon austenitizing temperature, distribution of lath width, and habit plane of martensitic structure in Fe-4Cr-0.4C steel has been studied by optical microscopy and transmission electron microscopy. The results obtained are as follows. 1) Optical microstructures of martensitic Fe-4Cr-0.4C steel consist of lath martensite and lens martensite. Also the four types of morphology are observed by electron microscopy. The most common morphologies are a regular paralleled martensite and an irregular dovetailed lath martensite, while the remainder of microstructures consists mainly of groups of internally twinned martensite and autotempered laths. 2) Prior austenite grain size and packet size increased with austenizing temperature, and also the numbers of lath contained in a prior austenite grain or a packet are increased with austenizing temperature. 3) The mean width of lath in Fe-4Cr-0.4C steel is about 0.23μm and most of lath widths are below 0.5μm. 4) Martensite habit plane of Fe-4Cr-0.4C steel is nearly [110]α'. (author)

  2. Isotope signatures of N2O emitted from vegetable soil: Ammonia oxidation drives N2O production in NH4(+)-fertilized soil of North China.

    Science.gov (United States)

    Zhang, Wei; Li, Yuzhong; Xu, Chunying; Li, Qiaozhen; Lin, Wei

    2016-07-08

    Nitrous oxide (N2O) is a potent greenhouse gas. In North China, vegetable fields are amended with high levels of N fertilizer and irrigation water, which causes massive N2O flux. The aim of this study was to determine the contribution of microbial processes to N2O production and characterize isotopic signature effects on N2O source partitioning. We conducted a microcosm study that combined naturally abundant isotopologues and gas inhibitor techniques to analyze N2O flux and its isotopomer signatures [δ(15)N(bulk), δ(18)O, and SP (intramolecular (15)N site preference)] that emitted from vegetable soil after the addition of NH4(+) fertilizers. The results show that ammonia oxidation is the predominant process under high water content (70% water-filled pore space), and nitrifier denitrification contribution increases with increasing N content. δ(15)N(bulk) and δ(18)O of N2O may not provide information about microbial processes due to great shifts in precursor signatures and atom exchange, especially for soil treated with NH4(+) fertilizer. SP and associated two end-member mixing model are useful to distinguish N2O source and contribution. Further work is needed to explore isotopomer signature stability to improve N2O microbial process identification.

  3. Hot Ductility Behaviors in the Weld Heat-Affected Zone of Nitrogen-Alloyed Fe-18Cr-10Mn Austenitic Stainless Steels

    Science.gov (United States)

    Moon, Joonoh; Lee, Tae-Ho; Hong, Hyun-Uk

    2015-04-01

    Hot ductility behaviors in the weld heat-affected zone (HAZ) of nitrogen-alloyed Fe-18Cr-10Mn austenitic stainless steels with different nitrogen contents were evaluated through hot tension tests using Gleeble simulator. The results of Gleeble simulations indicated that hot ductility in the HAZs deteriorated due to the formation of δ-ferrite and intergranular Cr2N particles. In addition, the amount of hot ductility degradation was strongly affected by the fraction of δ-ferrite.

  4. Resistance to pitting corrosion in ferritic and austenitic/ferritic steels

    International Nuclear Information System (INIS)

    De Bouvier, O.

    1995-01-01

    Stainless steel tubes carrying raw water are potentially vulnerable to pitting corrosion. With a view to minimizing the corrosion risk in the river-water-cooled condensers at PWR power plant, a study was conducted to determine initiation conditions and incubation durations for pitting corrosion in stagnant water. As a result, condenser tubes in Z2 CI 18 (439) or Z2 CT 18-10 (304L) steels were phased out in favour of Z2 CND 16-32 (316L) stainless steel. The same question can be yield for other applications and especially for all types of exchangers for use in electrical applications. This study sought to assess alternative methods for estimating pitting corrosion, and to check the results of these methods against the actual behaviour of studied steels. The study covered ferritic steels (439, 444, 290Mo), austenitic steel (316L) and austenitic/ferritic steels (Uranus 35N, 45N, 47N, 52N). Two approaches were adopted: laboratory tests to compare pitting corrosion risks on different materials, and tests for characterizing the behaviour of steels exposed to river water. The study begins with a laboratory tests that yield an arbitrary parameter for quantifying pitting corrosion resistance. One method involves measuring the pitting temperature in an aggressive ferric chloride solution. Other methods measure the pitting potential, either statistically (Multipit method) or deterministically (polarization curve). We then go on to discuss tests under simulated life-like conditions, involving repeated immersions in water from the Seine. (author). 9 refs., 13 figs, 9 tabs

  5. Heat treatment effects on structure and proerties of the alloy type KhN73MBNYu (EhJ 698)

    International Nuclear Information System (INIS)

    Maslenkov, S.B.; Maslenkova, E.A.; Solov'ev, Yu.V.; Zryumov, V.P.

    1994-01-01

    Influence of quenching temperature and various ageing conditions on tensile properties and impact strength of wrought alloy type KhN73MBTYu has been investigated at room temperature and in the range of 500-850 deg C. Two-step quenching followed by ageing at 700-750 deg C. Two-step quenching followed by ageing at 700-750 deg C is shown to assure needed heat resistance of the alloy. Due to the whole complex of structural changes during heat treatments mechanical properties of the alloy preserv high level up to 750 deg C. This temperature is limiting value in the case of long-term operation

  6. The influence of interstitial impurities on temperature ranges of deuterium retention in austenitic stainless steel 18Cr10NiTi

    International Nuclear Information System (INIS)

    Neklyudov, I.M.; Morozov, O.M.; Kulish, V.G.; Zhurba, V.I.; Galytsky, A.G.; Piatenko, E.V.

    2009-01-01

    The influence of nitrogen, oxygen and helium on the temperature range of deuterium retention in 18Cr10NiTi stainless steel (of AISI304L type) has been investigated. It is demonstrated that the introduction of oxygen, nitrogen or helium into 18Cr10NiTi steel extends the upper limit in the high-temperature range of deuterium retention. It has been found that for 18Cr10NiTi stainless steel, pre-irradiated with helium ions, the increase in the temperature range of deuterium retention occurs in steps: on attainment of helium concentration of ∼0.5 at.% He the temperature range increases by ∼100 K, and on attainment of helium concentration of ∼2.5 at.% He the temperature range increases by ∼350 K. The introduction of oxygen into 18Cr10NiTi stainless steel results in the increase of the temperature range of deuterium retention in the direction of rise in temperature. In the deuterium thermodesorption spectrum, this manifests itself by the occurrence of an additional low-amplitude peak with the maximum temperature T m ∼ 560 K. The introduction of nitric impurity into 18Cr10NiTi stainless steel results in the extension of the temperature range of deuterium retention towards higher temperatures.

  7. Ferritic stainless steels: corrosion resistance + economy

    International Nuclear Information System (INIS)

    Remus, A.L.

    1976-01-01

    Ferritic stainless steels provide corrosion resistance at lower cost. They include Type 409, Type 439, 18SR, 20-Mo (1.6 Mo), 18-2 (2 Mo), 26-1S, E-Brite 26-1, 29 Cr-4 Mo, and 29 Cr-4 Mo-2 Ni. Their corrosion and mechanical properties are examined. Resistance to stress-corrosion cracking is an advantage compared to austenitic types

  8. Crystal structure, quantum mechanical investigation, IR and NMR spectroscopy of two new organic perchlorates: (C6H18N3)·(ClO4)3H2O (I) and (C9H11N2)·ClO4(II)

    Science.gov (United States)

    Bayar, I.; Khedhiri, L.; Soudani, S.; Lefebvre, F.; Ferretti, V.; Ben Nasr, C.

    2018-06-01

    The reaction of perchloric acid with 1-(2-aminoethyl)piperazine or 5,6-dimethyl-benzimidazole results in the formation of 1-(2-amonioethyl)piperazine-1,4-dium triperchlorate hydrate (C6H18N3)·(ClO4)3·H2O (I) or 5,6-dimethyl-benzylimidazolium perchlorate (C9H11N2)·ClO4(II). Both compounds were fully structurally characterized including single crystal X-ray diffraction analysis. Compound (I) crystallizes in the centrosymmetric triclinic space group P 1 bar with the lattice parameters a = 7.455 (2), b = 10.462 (2), c = 10.824 (2) Å, α = 80.832 (2), β = 88.243 (2), γ = 88.160 (2) °, Z = 2 and V = 832.77 (3) Å3. Compound (II) has been found to belong to the P21/c space group of the monoclinic system, with a = 7.590 (3), b = 9.266 (3), c = 16.503 (6) Å, β = 107.38 (2) °, V = 1107.69 (7) Å3 and Z = 4. The structures of (I) and (II) consist of slightly distorted [ClO4]- tetrahedra anions and 1-(2-amonioethyl)piperazine-1,4-dium trication (I) or 5,6-dimethyl-benzylimidazolium cations (II) and additionally a lattice water in (I). The crystal structures of (I) and (II) exhibit complex three-dimensional networks of H-bonds connecting all their components. In the atomic arrangement of (I), the ClO4- anions form corrugated chains, while in (II) the atomic arrangement exhibits wide pseudo-hexagonal channels of ClO4 tetrahedra including the organic entities. The lattice water serves as a link between pairs of cations and pairs of anions via several Osbnd H⋯O and N-H⋯O interactions in compound (I). The vibrational absorption bands were identified by infrared spectroscopy. These compounds were also investigated by solid-state 13C, 35Cl and 15N NMR spectroscopy. DFT calculations allowed the attribution of the IR and NMR bands. Intermolecular interactions were investigated by Hirshfeld surfaces. Electronic properties such as HOMO and LUMO energies were derived.

  9. Synthesis of (E-2,4-Dinitro-N-((2E,4E-4-phenyl-5-(pyrrolidin-1-ylpenta-2,4-dienylideneaniline

    Directory of Open Access Journals (Sweden)

    Mostafa Fesanghari

    2009-07-01

    Full Text Available (E-2,4-Dinitro-N-((2E,4E-4-phenyl-5-(pyrrolidin-1-ylpenta-2,4-dienylidene aniline dye was prepared in one pot by reaction of premade N-2,4-dinitrophenyl-3-phenylpyridinium chloride (DNPPC and pyrrolidine in absolute MeOH.

  10. Elevated Temperature Corrosion Studies of AlCrN and TiAlN Coatings by PAPVD on T91 Boiler Steel

    Science.gov (United States)

    Goyal, Lucky; Chawla, Vikas; Hundal, Jasbir Singh

    2017-11-01

    The present investigation discusses the hot corrosion behavior of AlCrN and TiAlN nano-coatings on T91 boiler steel by PAPVD process subjected to molten salt of Na2SO4-60%V2O5 at 900 °C for 50 cycles. Surface and cross-sectional studies were performed by AFM, SEM/EDS and XRD techniques to understand the corrosion kinetics and mechanism. T91 bare boiler steel as well as TiAlN-coated specimen has shown higher internal oxidation as well as weight gain. The better corrosion resistance of AlCrN-coated specimen has been observed by virtue of higher availability of Cr and Al in the oxide scale as well as adherent and dense coating. The betterment of AlCrN coating can be attributed to low internal oxidation as well as movement of Cr and Al toward oxide scale to form protective corrosion barriers.

  11. Improvements in the susceptibility to hydrogen attack and stress-relief cracking of 2 1/4Cr-1Mo steels

    International Nuclear Information System (INIS)

    Imanaka, T.; Sato, S.; Shimomura, J.; Aso, K.

    1985-01-01

    The influence of sulphur content at extremely low level on the susceptibility to hydrogen attack and stress-relief cracking in 2 1/4Cr-1Mo steels was studied. The reduction of sulphur content and/or the addition of REM (rare earth metal) or Ca in accordance with sulphur content remarkably improve the resistivity against hydrogen attack and stress-relief cracking. Micro-structural examination has showed that there exist Mn-REM-S-Al-O complex particles in the REM-added steels. It is concluded that the effect of REM on hydrogen attack and stress-relief cracking is to reduce ''the free sulphur'' in 2 1/4Cr-1Mo steels

  12. ESTIMASI NILAI VaR PORTOFOLIO MENGGUNAKAN FUNGSI ARCHIMEDEAN COPULA

    Directory of Open Access Journals (Sweden)

    AULIA ATIKA PRAWIBTA SUHARTO

    2017-01-01

    Full Text Available Value at Risk explains the magnitude of the worst losses occurred in financial products investments with a certain level of confidence and time interval. The purpose of this study is to estimate the VaR of portfolio using Archimedean Copula family. The methods for calculating the VaR are as follows: (1 calculating the stock return; (2 calculating descriptive statistics of return; (3 checking for the nature of autocorrelation and heteroscedasticity effects on stock return data; (4 checking for the presence of extreme value by using Pareto tail; (5 estimating the parameters of Achimedean Copula family; (6 conducting simulations of Archimedean Copula; (7 estimating the value of the stock portfolio VaR. This study uses the closing price of TLKM and GGRM. At 90% the VaR obtained using Clayton, Gumbel, Frank copulas are 0.9562%, 1.0189%, 0.9827% respectively. At 95% the VaR obtained using Clayton, Gumbel, Frank copulas are 1.2930%, 1.2522%, 1.3152% respectively. At 99% the VaR obtained using Clayton, Gumbel, Frank copulas are 2.0327%, 1.9164%, is 1.8678% respectively. In conclusion estimation of VaR using Clayton copula yields the highest VaR.

  13. Evaluation of crack growth behavior and probabilistic S–N characteristics of carburized Cr–Mn–Si steel with multiple failure modes

    International Nuclear Information System (INIS)

    Li, Wei; Sun, Zhenduo; Zhang, Zhenyu; Deng, Hailong; Sakai, Tatsuo

    2014-01-01

    Highlights: • The stepwise S–N characteristics only for interior induced failure was observed. • The interior crack growth behavior with threshold conditions in different stages was clarified. • The distribution characteristics of test data in transition failure region was evaluated. • A model for evaluating the probabilistic S–N curve with multiple failure modes was developed. - Abstract: The unexpected failures of case-hardened steels in long life regime have been a critical issue in modern engineering design. In this study, the failure behavior of a carburized Cr–Mn–Si steel under very high cycle fatigue (VHCF) was investigated, and a model for evaluating the probabilistic S–N curve associated with multiple failure modes was developed. Results show that the carburized Cr–Mn–Si steel exhibits three failure modes including the surface flaw-induced failure, the interior inclusion-induced failure without the fine granular area (FGA) and the interior inclusion-induced failure with the FGA. As the predominant failure mode in the VHCF regime, the interior failure process can be divided into four stages: (i) the small crack growth around the inclusion, (ii) the stable macroscopic crack growth outside the FGA, (iii) the unstable crack growth outside the fish-eye and (iv) the momentary fracture outside the final crack growth zone. The threshold values are successively evaluated to be 2.33 MPa m 1/2 , 4.13 MPa m 1/2 , 18.51 MPa m 1/2 and 29.26 MPa m 1/2 . The distribution characteristics of the test data in transition failure region can be well characterized by the mixed two-parameter Weibull distribution function. The developed probabilistic S–N curve model is in good agreement with the test data with multiple failure modes. Although the result is somewhat conservative in the VHCF regime, it is acceptable for safety considerations

  14. On the relationship between corrosion inhibiting effect and molecular structure of 2,5-bis(n-pyridyl)-1,3,4-thiadiazole derivatives in acidic media: Ac impedance and DFT studies

    Energy Technology Data Exchange (ETDEWEB)

    Bentiss, F., E-mail: fbentiss@enscl.f [Laboratoire de Chimie de Coordination et d' Analytique (LCCA), Faculte des Sciences, Universite Chouaib Doukkali, B.P. 20, M-24000 El Jadida (Morocco); Mernari, B. [Laboratoire de Chimie de Coordination et d' Analytique (LCCA), Faculte des Sciences, Universite Chouaib Doukkali, B.P. 20, M-24000 El Jadida (Morocco); Traisnel, M. [Unite Materiaux et Transformations (UMET), Ingenierie des Systemes Polymeres, CNRS UMR 8207, ENSCL, B.P. 90108, F-59652 Villeneuve d' Ascq Cedex (France); Vezin, H. [Laboratoire de Spectrochimie Infrarouge et Raman (LASIR), UMR-CNRS 8516, Universite des Sciences et Technologies de Lille, Batiment C5, F-59655 Villeneuve d' Ascq Cedex (France); Lagrenee, M., E-mail: michel.lagrenee@ensc-lille.f [Unite de Catalyse et de Chimie du Solide (UCCS), UMR-CNRS 8181, ENSCL, B.P. 90108, F-59652 Villeneuve d' Ascq Cedex (France)

    2011-01-15

    Research highlights: {yields}2,5-Bis(n-pyridyl)-1,3,4-thiadiazoles (n-PTH) act as good inhibitors for the mild steel in acidic media. {yields}The inhibiting protection depends on the position of the nitrogen on the pyridinium substituent according to order 3-PTH > 2-PTH > 4-PTH. {yields}The adsorption of n-PTH is found to follow the Langmuir's adsorption isotherm. {yields}Data obtained from quantum chemical calculations using DFT method were correlated to the experimentally obtained inhibition efficiencies. - Abstract: The inhibition properties of 2,5-bis(n-pyridyl)-1,3,4-thiadiazoles (n-PTH) on corrosion of mild steel in different acidic media (1 M HCl, 0.5 M H{sub 2}SO{sub 4} and 1 M HClO{sub 4}) were analyzed by electrochemical impedance spectroscopy (EIS). The n-PTH derivatives exhibit good inhibition properties in different acidic solutions and the calculated values of {Delta}G{sub ads}{sup 0} revealed that the adsorption mechanism of n-PTH on steel surface is mainly due to chemisorption. While in 1 M HClO{sub 4}, both 2-PTH and 4-PTH isomers stimulate the corrosion process especially at low concentrations. Quantum chemical calculations using the density functional theory (DFT) were performed on n-PTH derivatives to determine the relationship between molecular structure and their inhibition efficiencies. The results of the quantum chemical calculations and experimental inhibition efficiency were subjected to correlation analysis and indicate that the inhibition effects of n-PTH may be explained in terms of electronic properties.

  15. Tool life equation for blanking 18-8 stainless steel strips

    Directory of Open Access Journals (Sweden)

    Faura, F.

    1998-08-01

    Full Text Available Hereinafter it is presented a model for the behaviour and life of circular blanking tool used in sheet forming processes of 18-8 stainless steel (sheet thickness: 1 mm. Firstly it has analyzed the different studies that have previously delt with this problem. Secondly taking into account recently made experiments, it is proposed a simple formulation to predict tool life with enough reliability. To this purpose it has examined different parameters in the wear process, inferring from these the fundamental parameters that regulate them and about which the different equations have been configurated. Blanking tests were performed using a 20 t press at a speed of 150 strokes/min. Punch materials used in these tests were AISI A2 and AISI D2 with diameters between 1.5 and 10 mm. The blanking tests were performed at a clearance between 5 and 20 % of the work material thickness.

    En el presente artículo se presenta un modelo de ecuación de vida de herramientas para punzonado circular de chapa de acero inoxidable 18-8 (1 mm de espesor. Se han analizado inicialmente los diferentes estudios que previamente han abordado este problema. Posteriormente, teniendo en cuenta los experimentos realizados recientemente, se propone una formulación simple para predecir con Habilidad suficiente la vida de la herramienta. Para este propósito se han examinado los diferentes parámetros que afectan al proceso de desgaste, infiriendo a partir de estos, los parámetros fundamentales que lo regulan y sobre los cuales se han configurado las diferentes ecuaciones. Los ensayos fueron realizados en una prensa de 20 t y una velocidad de punzonado de 150 golpes/min. Los materiales de los punzones usados en los ensayos fueron AISI A2 y AISI D2 con diámetros comprendidos entre 1,5 y 10 mm. Los ensayos se realizaron para juegos de corte comprendidos entre un 5 y 20 % del espesor de la chapa.

  16. Interaction of inhibitors with corrosion scale formed on N80 steel in CO{sub 2}-saturated NaCl solution

    Energy Technology Data Exchange (ETDEWEB)

    Liu, D. [School of Chemistry and Chemical Engineering, Huazhong University of Science and Technology, Hubei Key Laboratory of Materials Chemistry and Service Failure, Wuhan (China); School of Chemical Engineering and Pharmacy, Key Laboratory for Green Chemical Process of Ministry of Education, Wuhan Institute of Technology, Wuhan (China); Qiu, Y.B.; Guo, X.P. [School of Chemistry and Chemical Engineering, Huazhong University of Science and Technology, Hubei Key Laboratory of Materials Chemistry and Service Failure, Wuhan (China); Tomoe, Y.; Bando, K. [Japan Oil, Gas and Metals National Corporation, The Former Japan National Oil Corporation, Hamada, Mihama-ku, Chiba-City, Chiba (Japan)

    2011-12-15

    The performance of the selected inhibitors, including thioglycolic acid (TGA), diethylenetriamine (DETA), and naphthene acid imidazolines (IM), on the bare surface of N80 steel and its scaled surface pre-corroded in CO{sub 2}-saturated 1%NaCl solution was investigated by weight-loss method, electrochemical measurements using rotating cylinder electrode and surface analytical methods (SEM, XRD, and EPMA). The results indicate that there is a remarkable difference in inhibition efficiency of inhibitors on the N80 steel with and without pre-corrosion scale. The synergistic effect between inhibitors and corrosion scale not only depends on the size of inhibitor molecules, but also depends on the interaction of the inhibitor with the corrosion scale. It shows that IM and DETA have a good positive synergistic effect with the corrosion scale formed on N80 steel, although DETA has no inhibition efficiency for bare N80 steel, which can easily enter into the apertures of the corrosion scale, and block the active sites on the metal surface and the diffusion routeways of the reactant so as to depress the corrosion of the substrate metal. While TGA shows excellent inhibition efficiency on bare N80 steel, but it has an antagonistic effect with the corrosion scale although it has a small molecular weight as well as DETA, because TGA can dissolve corrosion scale and break its integrality and protectiveness performance. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  17. In vivo evaluation in rats of [{sup 18}F]1-(2-fluoroethyl)-4-[(4-cyanophenoxy)methyl]piperidine as a potential radiotracer for PET assessment of CNS sigma-1 receptors

    Energy Technology Data Exchange (ETDEWEB)

    Waterhouse, Rikki N. [Department of Psychiatry, Columbia University, New York, NY 10032 (United States) and Department of Radiology, Columbia University, New York, NY 10032 (United States) and Neurobiology and Imaging Program, Department of Biological Psychiatry, New York State Psychiatric Institute, New York, NY 10032 (United States)]. E-mail: rnw7@columbia.edu; Chang, Raymond C. [Department of Psychiatry, Columbia University, New York, NY 10032 (United States); Neurobiology and Imaging Program, Department of Biological Psychiatry, New York State Psychiatric Institute, New York, NY 10032 (United States); Zhao, Jun [Department of Psychiatry, Columbia University, New York, NY 10032 (United States); Neurobiology and Imaging Program, Department of Biological Psychiatry, New York State Psychiatric Institute, New York, NY 10032 (United States); Carambot, Patty E. [Department of Psychiatry, Columbia University, New York, NY 10032 (United States); Neurobiology and Imaging Program, Department of Biological Psychiatry, New York State Psychiatric Institute, New York, NY 10032 (United States)

    2006-02-15

    Introduction: Sigma-1 receptors are expressed throughout the mammalian central nervous system (CNS) and are implicated in several psychiatric disorders, including schizophrenia and depression. We have recently evaluated the high-affinity (K {sub D}=0.5{+-}0.2 nM, log P=2.9) sigma-1 receptor radiotracer [{sup 18}F]1-(3-fluoropropyl)-4-(4-cyanophenoxymethyl)piperidine, [{sup 18}F]FPS, in humans. In contrast to appropriate kinetics exhibited in baboon brain, in the human CNS, [{sup 18}F]FPS does not reach pseudoequilibrium by 4 h, supporting the development of a lower-affinity tracer [Waterhouse RN, Nobler MS, Chang RC, Zhou Y, Morales O, Kuwabara H, et al. First evaluation of the sigma-1 receptor radioligand [{sup 18}F]1-3-fluoropropyl-4-((4-cyanophenoxy)-methyl)piperidine ([{sup 18}F]FPS) in healthy humans. Neuroreceptor Mapping 2004, July 15-18th, Vancouver, BC Canada 2004]. We describe herein the in vivo evaluation in rats of [{sup 18}F]1-(2-fluoroethyl)-4-[(4-cyanophenoxy)methyl]piperidine ([{sup 18}F]SFE) (K {sub D}=5 nM, log P=2.4), a structurally similar, lower-affinity sigma-1 receptor radioligand. Methods: [{sup 18}F]SFE was synthesized (n=4) as previously described in good yield (54{+-}6% EOB), high specific activity (2.1{+-}0.6 Ci/{mu}mol EOS) and radiochemical purity (98{+-}1%) and evaluated in awake adult male rats. Results: Similar to [{sup 18}F]FPS, regional brain radioactivity concentrations [percentage of injected dose per gram of tissue (%ID/g), 15 min] for [{sup 18}F]SFE were highest in occipital cortex (1.86{+-}0.06 %ID/g) and frontal cortex (1.76{+-}0.38 %ID/g), and lowest in the hippocampus (1.01{+-}0.02%ID/g). Unlike [{sup 18}F]FPS, [{sup 18}F]SFE cleared from the brain with {approx}40% reduction in peak activity over a 90-min period. Metabolite analysis (1 h) revealed that [{sup 18}F]SFE was largely intact in the brain. Blocking studies showed a large degree (>80%) of saturable binding for [{sup 18}F]SFE in discrete brain regions. Conclusions

  18. An automated setup to measure paleoatmospheric δ13C-CH4, δ15N-N2O and δ18O-N2O in one ice core sample

    NARCIS (Netherlands)

    Sperlich, P.; Buizert, C.; Jenk, T.M.; Sapart, C.J.; Prokopiou, M.; Röckmann, T.; Blunier, T.

    2013-01-01

    Air bubbles in ice core samples represent the only opportunity to study the isotopic variability of paleoatmospheric CH4 and N2O. The highest possible precision in isotope measurements is required to maximize the resolving power for CH4 and N2O sink and source reconstructions. We present a new setup

  19. Synthesis and Physical and Chemical Properties of Hypergolic Chemicals such as N,N,N-Trimethylhydrazinium and 1-Ethyl-4-Methyl-1,2,4-Triazolium Salts

    Directory of Open Access Journals (Sweden)

    Young-Seok Kim

    2015-12-01

    Full Text Available Hypergolic chemicals N,N,N-trimethylhydrazinium iodide, [TMH]+[I]−, and 1-ethyl-4-methyl-1,2,4-triazolium iodide, [EMT]+[I]− were firstly synthesized by nucleophilic substitution (SN2. The successful synthesis of hypergolic chemicals [TMH]+[I]− and [EMT]+[I]− was confirmed by IR and 1H-NMR spectroscopy and, GC-mass spectrometry. Subsequently the hypergolic chemicals [TMH]+[X]− (X = CN−, N3−, NO3−, NO2−, ClO4−, AlCl4− were prepared via an ion exchange reaction from [TMH]+[I]− and [EMT]+[I]−, respectively. After that, a mixture of hypergolic chemicals was prepared by dissolving the synthesized hypergolic chemicals in 2-hydroxyethylhydrazine (HOCH2CH2NHNH2. The physical and chemical properties of the mixture such as decomposition temperature (Td, density (d, viscosity (η, and decomposition energy (ΔHd was then evaluated to determine suitability for use as liquid rocket fuels. The ignition delay (ID time of the mixture of hypergolic chemicals with [TMH]+[N3]− and [TMH]+[CN]− using H2O2 as an oxidizer was determined as 55.6 ms and 97.4 ms; respectively. The ID time of the mixture of hypergolic chemicals with [EMT]+[N3]−; [EMT]+[CN]−; [EMT]+[AlCl4]−; and [EMT]+[I]− using H2O2 as an oxidizer was also determined as 18.0 ms; 32.6 ms; 27.6 ms; and 7.96 ms; respectively. The synthesized mixture of hypergolic chemicals could thus be used as a rocket propellant liquid fuel.

  20. Evaluation of environmental effect on creep-fatigue of 2 1/4Cr-1Mo steel

    International Nuclear Information System (INIS)

    Yang Beinan; Ishikawa, Akiyoshi; Asada, Yasuhide.

    1991-01-01

    In the present study, a trial evaluation was made to evaluate the environmental effect of air separately from the behavior of material origin. Data with 2 1/4Cr-1Mo steel at 550degC in air were subjected to the evaluation based on data of the steel in high vacuum with a newly developed procedure using the overstress concept. An empirical expression was proposed to describe the environmental effect of air on the creep-fatigue behavior. Following conclusions were obtained in the present study on a separation of the environmental effect of air on a creep-fatigue behavior of 2 1/4Cr-1Mo steel at 550degC. 1) The environmental effect of air reduces a fatigue life, that is, it increases the time-independent damage component of the creep-fatigue. 2) The environmental effect of air brings on the frequency effect which is mainly dependent upon a strain rate or time in a compression going stroke. Other environmental effect on F-S or compression hold-time cycles depends upon the strain rate in compression. 3) The rate-time dependent damage component, that is, the creep damage is reduced by the environmental effect of air. That means a creep-fatigue life recovers in air environment. (author)

  1. Nontoxic corrosion inhibitors for N80 steel in hydrochloric acid

    Directory of Open Access Journals (Sweden)

    M. Yadav

    2016-11-01

    Full Text Available The purpose of this paper is to evaluate the protective ability of 1-(2-aminoethyl-2-oleylimidazoline (AEOI and 1-(2-oleylamidoethyl-2-oleylimidazoline (OAEOI as corrosion inhibitors for N80 steel in 15% hydrochloric acid, which may find application as eco-friendly corrosion inhibitors in acidizing processes in petroleum industry. Different concentrations of synthesized inhibitors AEOI and OAEOI were added to the test solution (15% HCl and the corrosion inhibition of N80 steel in hydrochloric acid medium containing inhibitors was tested by weight loss, potentiodynamic polarization and AC impedance measurements. Influence of temperature (298–323 K on the inhibition behavior was studied. Surface studies were performed by using FTIR spectra and SEM. Both the inhibitors, AEOI and OAEOI at 150 ppm concentration show maximum efficiency 90.26% and 96.23%, respectively at 298 K in 15% HCl solution. Both the inhibitors act as mixed corrosion inhibitors. The adsorption of the corrosion inhibitors at the surface of N80 steel is the root cause of corrosion inhibition.

  2. Removal of corrosion products of construction materials in heat carrier

    International Nuclear Information System (INIS)

    1975-01-01

    A review of reported data has been made on the removal of structural material corrosion products into the heat-carrying agent of power reactors. The corrosion rate, and at the same time, removal of corrosion products into the heat-carrying agent (water) decreases with time. Thus, for example, the corrosion rate of carbon steel in boiling water at 250 deg C and O 2 concentration of 0.1 mg/1 after 3000 hr is 0.083 g/m 2 . day; after 9000 hr the corrosion rate has been reduced 2.5 times. Under static conditions the transfer rate of corrosion products into water has been smaller than in the stream and also depends on time. The corrosion rate of carbon steel under nuclear plant operating conditions is almost an order higher over that of steel Kh18N10T

  3. Radiosynthesis and pre-clinical evaluation of [{sup 18}F]fluoro-[1,2-{sup 2}H{sub 4}]choline

    Energy Technology Data Exchange (ETDEWEB)

    Smith, Graham [Comprehensive Cancer Imaging Centre, Faculty of Medicine, Imperial College London, Hammersmith Hospital, Du Cane Road, London W12 0NN (United Kingdom); Zhao Yongjun [MDx Discovery (part of GE Healthcare) at Hammersmith Imanet, Ltd., Hammersmith Hospital, Du Cane Road, London W12 0NN (United Kingdom); Leyton, Julius [Comprehensive Cancer Imaging Centre, Faculty of Medicine, Imperial College London, Hammersmith Hospital, Du Cane Road, London W12 0NN (United Kingdom); Shan Bo [MDx Discovery (part of GE Healthcare) at Hammersmith Imanet, Ltd., Hammersmith Hospital, Du Cane Road, London W12 0NN (United Kingdom); Nguyen, Quang-de; Perumal, Meg [Comprehensive Cancer Imaging Centre, Faculty of Medicine, Imperial College London, Hammersmith Hospital, Du Cane Road, London W12 0NN (United Kingdom); Turton, David [GE-Imanet, Hammersmith Hospital, Du Cane Road, London, W12 0NN (United Kingdom); Arstad, Erik; Luthra, Sajinder K.; Robins, Edward G. [MDx Discovery (part of GE Healthcare) at Hammersmith Imanet, Ltd., Hammersmith Hospital, Du Cane Road, London W12 0NN (United Kingdom); Aboagye, Eric O., E-mail: eric.aboagye@imperial.ac.u [Comprehensive Cancer Imaging Centre, Faculty of Medicine, Imperial College London, Hammersmith Hospital, Du Cane Road, London W12 0NN (United Kingdom)

    2011-01-15

    Introduction: Choline radiotracers are widely used for clinical PET diagnosis in oncology. [{sup 11}C]Choline finds particular utility in the imaging of brain and prostate tumor metabolic status, where 2-[{sup 18}F]fluoro-2-deoxy-D-glucose ('FDG') shows high background uptake. More recently we have extended the clinical utility of [{sup 11}C]choline to breast cancer where radiotracer uptake correlates with tumor aggressiveness (grade). In the present study, a new choline analog, [{sup 18}F]fluoro-[1,2-{sup 2}H{sub 4}]choline, was synthesized and evaluated as a potential PET imaging probe. Methods: [{sup 18}F]Fluorocholine, [{sup 18}F]fluoro-[1-{sup 2}H{sub 2}]choline and [{sup 18}F]fluoro-[1,2-{sup 2}H{sub 4}]choline were synthesized by alkylation of the relevant precursor with [{sup 18}F]fluorobromomethane or [{sup 18}F]fluoromethyl tosylate. Radiosynthesis of [{sup 18}F]fluoromethyl tosylate required extensive modification of the existing method. [{sup 18}F]Fluorocholine and [{sup 18}F]fluoro-[1,2-{sup 2}H{sub 4}]choline were then subjected to in vitro oxidative stability analysis in a chemical oxidation model using potassium permanganate and an enzymatic model using choline oxidase. The two radiotracers, together with the corresponding di-deuterated compound, [{sup 18}F]fluoro-[1-{sup 2}H{sub 2}]choline, were then evaluated in vivo in a time-course biodistribution study in HCT-116 tumor-bearing mice. Results: Alkylation with [{sup 18}F]fluoromethyl tosylate proved to be the most reliable radiosynthetic route. Stability models indicate that [{sup 18}F]fluoro-[1,2-{sup 2}H{sub 4}]choline possesses increased chemical and enzymatic (choline oxidase) oxidative stability relative to [{sup 18}F]fluorocholine. The distribution of the three radiotracers, [{sup 18}F]fluorocholine, [{sup 18}F]fluoro-[1-{sup 2}H{sub 2}]choline and [{sup 18}F]fluoro-[1,2-{sup 2}H{sub 4}]choline, showed a similar uptake profile in most organs. Crucially, tumor uptake of [{sup 18}F

  4. Characteristics of centrifugally cast GX25CrNiSi18-9 steel

    Directory of Open Access Journals (Sweden)

    R. Zapała

    2011-07-01

    Full Text Available The paper presents the results of microstructural examinations of the industrial heat-resistant centrifugally cast GX25CrNiSi18-9 steel characterised by increased content of Cu. The study included changes in the microstructure of base cast steel respective of the steel held at a temperature of 900 and 950°C for 48 hours. Based on the results obtained, an increase in microhardness of the examined cast steel matrix with increasing temperature was stated, which was probably caused by fine precipitates enriched in Cr, Mo, and C forming inside the matrix grains.The layer of scale formed on the tested cast steel oxidised in the atmosphere of air at 900 and 950°C was characterised by an increased tendency to degradation with increasing temperature of the conducted tests.

  5. Characteristics Associated With Utilization of VA and Non-VA Care Among Iraq and Afghanistan Veterans With Post-Traumatic Stress Disorder.

    Science.gov (United States)

    Finley, Erin P; Mader, Michael; Bollinger, Mary J; Haro, Elizabeth K; Garcia, Hector A; Huynh, Alexis K; Pugh, Jacqueline A; Pugh, Mary Jo

    2017-11-01

    Post-traumatic stress disorder (PTSD) affects nearly one-fifth of Iraq and Afghanistan Veterans (IAV). The Department of Veterans Affairs (VA) has invested in making evidence-based psychotherapies for PTSD available at every VA facility nationwide; however, an unknown number of veterans opt to receive care in the community rather than with VA. We compared PTSD care utilization patterns among Texas IAV with PTSD, an ethnically, geographically, and economically diverse group. To identify IAV in Texas with service-connected disability for PTSD, we used a crosswalk of VA administrative data from the Operation Enduring Freedom/Operation Iraqi Freedom Roster and service-connected disability data from the Veterans Benefits Administration. We then surveyed a random sample of 1,128 veterans from the cohort, stratified by sex, rurality, and past use/nonuse of any VA care. Respondents were classified into current utilization groups (VA only, non-VA only, dual care, and no professional PTSD treatment) on the basis of reported PTSD care in the prior 12 months. Responses were weighted to account for sample stratification and for response rate within each strata. Utilization group characteristics were compared to the population mean using the one sample Z-test for proportions, or the t-test for means. A multinomial logistic regression model was used to identify survey variables significantly associated with current utilization group. 249 IAV completed the survey (28.4% response rate). Respondents reported receiving PTSD care: in the VA only (58.3%); in military or community-based settings (including private practitioners) (non-VA only, 8.7%); and in both VA and non-VA settings (dual care, 14.5%). The remainder (18.5%) reported no professional PTSD care in the prior year. Veterans ineligible for Department of Defense care, uncomfortable talking about their problems, and opposed to medication were more likely to receive non-VA care only, whereas those with lower household income

  6. Evaluación de la eficacia de VA-MENGOC-BC® en ratón Balb/c retados frente a los serogrupos A, B y C

    Directory of Open Access Journals (Sweden)

    Juan Francisco Infante

    2003-09-01

    Full Text Available Hasta la fecha se han desarrollado varios modelos experimentales para la reproducción experimental de la enfermedad meningocócica humana, cuya utilidad en la evaluación de la eficacia de medios de inmunización y terapia, así como en el estudio de la patogenia de la enfermedad es incuestionable. En el presente trabajo se describe la evaluación de la eficacia de VA-MENGOC-BC® y la Inmunoglobulina Humana Antimeningocócica BC frente a Neisseria meningitidis de los serogrupos A, B y C, empleando el ratón Balb/c tratado con mucina y dextrana férrica como estimulantes de la virulencia. Los ratones fueron inmunizados por vía intraperitoneal con una, dos o tres dosis de 0,5 mL de VA-MENGOC-BC®. El intervalo entre dosis fue de tres semanas entre la primera y segunda dosis y de 15 días entre la segunda y la tercera. El reto se realizó con dosis letales (1-3 x DL50 de N. meningitidis A, B ó C a los 15 ó 21 días después de aplicada la última dosis de vacuna. Para evaluar la actividad de la Inmunoglobulina Antimeningocócica BC como medio de inmunización pasiva, se trató otro grupo de ratones, 30 min, 2 y 6 h después habérseles inoculado los gérmenes. Se administraron en cada caso 5 mg de la inmunoglobulina por vía intraperitoneal o intravenosa en un volumen de 0,1 mL. Los resultados demostraron que tanto VA-MENGOC-BC® como la Globulina Antimeningocócica BC confieren protección significativa contra un reto letal con N. meningitidis en el modelo de ratón tratado con factores estimulantes de la virulencia.

  7. Phase transformation and grain growth behavior of a nanocrystalline 18/8 stainless steel

    Energy Technology Data Exchange (ETDEWEB)

    Kotan, Hasan, E-mail: hasankotan@gmail.com [Konya Necmettin Erbakan University, Department of Metallurgical & Materials Engineering, Konya 42090 (Turkey); Darling, Kris A. [US Army Research Laboratory, Weapons and Materials Research Directorate, RDRL-WMM-F, Aberdeen Proving Ground, MD 21005-5069 (United States)

    2017-02-16

    Fe-18Cr-8Ni and Fe-18Cr-8Ni-1Y (at%) stainless steel powders were nanostructured by mechanical alloying from elemental powders and subjected to 90 min annealing treatments at various temperatures. The microstructural evolutions as a function of alloy compositions and temperatures were investigated by in-situ and ex-situ x-ray diffraction experiments, transmission electron microscopy and focused ion beam microscopy. The dependence of hardness on the microstructure was utilized to study the mechanical changes. It was found that the resulting microstructures by mechanical alloying were bcc solid solution, the so-called α’-martensite structure. The high temperature in-situ x-ray diffraction experiments showed that the martensite-to-austenite reverse phase transformation was completed above 800 and 900 °C for Fe-18Cr-8Ni and Fe-18Cr-8Ni-1Y steels, respectively. A partial or complete retransformation to martensite was observed upon cooling to room temperature. Annealing of nanocrystalline Fe-18Cr-8Ni steel yielded grain growth reaching to micron sizes at 1100 °C while addition of 1 at% yttrium stabilized the microstructure around 160 nm grain size and 6 GPa hardness after 90 min annealing at 1200 °C.

  8. Compound effect of CaCO{sub 3} and CaSO{sub 42H{sub 2}O on the strength of steel slag: cement binding materials

    Energy Technology Data Exchange (ETDEWEB)

    Qi, Liqian; Liu, Jiaxiang; Liu, Qian, E-mail: ljxpost@263.net [Beijing Key Laboratory of Electrochemical Process and Technology for Materials, The State Key Laboratory of Chemical Resource Engineering, Beijing University of Chemical Technology, Beijing (China)

    2016-03-15

    In this study, we replaced 30% of the cement with steel slag to prepare binding material; additionally, small amounts of CaCO{sub 3} and CaSO{sub 42H{sub 2}O were added. This was done to study the compound effect of CaCO{sub 3} and CaSO{sub 42H{sub 2}O on the strength of steel slag-cement binding materials. The hydration degree of the steel slag cementitious material was analyzed by XRD, TG and SEM. The results showed that the optimum proportions of CaCO{sub 3} and CaSO{sub 42H{sub 2}O were 3% and 2%, respectively. Compared with the steel slag-cement binders without adding CaCO{sub 3} and CaSO{sub 42H{sub 2}O, the compressive strength increased by 59.9% at 3 days and by 17.8% at 28 days. Acting as the nucleation matrix, CaCO{sub 3} could accelerate the hydration of C{sub 3}S. In addition, CaCO{sub 3} was involved in the hydration reaction, generating a new hydration product, which could stably exist in a slurry. Meanwhile, CaSO{sub 42H{sub 2}O could increase the number of AFt. The compound effect of CaCO{sub 3} and CaSO{sub 42H{sub 2}O enhanced the intensity of steel slag-cement binding materials and improved the whole hydration behavior. (author)

  9. Synthesis and structure of the extended phosphazane ligand [(1,4-C6H4){N(μ-PN(t)Bu)2N(t)Bu}2](4).

    Science.gov (United States)

    Sevilla, Raquel; Less, Robert J; García-Rodríguez, Raúl; Bond, Andrew D; Wright, Dominic S

    2016-02-07

    The reaction of the phenylene-bridged precursor (1,4-C6H4)[N(PCl2)2]2 with (t)BuNH2 in the presence of Et3N gives the new ligand precursor (1,4-C6H4)[N(μ-N(t)Bu)2(PNH(t)Bu)2]2, deprotonation of which with Bu2Mg gives the novel tetraanion [(1,4-C6H4){N(μ-N(t)Bu)2(PN(t)Bu)2}2](4-).

  10. Certain peculiarities of structural inheritance in phase recrystallization of steel

    International Nuclear Information System (INIS)

    Mukhamedov, A.A.

    1978-01-01

    The structural inheritance in phase recrystallization of previously overheated to various temperatures industrially melted 40Kh steel and of Armco-iron has been investigated. The steels have been heated to 100O, 11O0, 1200 and 1260 deg C and cooled in the air, and in some instances, hardened (quenched) in water. The physical broadening of X-ray lines points to a nonmonotonous variation of fine structure parameters as a function of the temperature and the heating time. The inheritance effect of fine structure defects affects the steel properties obtained in a final heat treatment. The structural inheritance effect has an important bearing upon the wear resistance of steel. A purpose-oriented use of the structural inheritance effect can enhance service properties of steel parts

  11. Determination of ultra-short laser induced damage threshold of KH{sub 2}PO{sub 4} crystal: Numerical calculation and experimental verification

    Energy Technology Data Exchange (ETDEWEB)

    Cheng, Jian [Center for Precision Engineering, School of Mechatronics Engineering, Harbin Institute of Technology, Harbin 150001 (China); Department of Physics, The Ohio State University, 191 W. Woodruff Ave, Columbus, OH 43210 (United States); Chen, Mingjun, E-mail: chenmj@hit.edu.cn, E-mail: chowdhury.24@osu.edu; Wang, Jinghe; Xiao, Yong [Center for Precision Engineering, School of Mechatronics Engineering, Harbin Institute of Technology, Harbin 150001 (China); Kafka, Kyle; Austin, Drake; Chowdhury, Enam, E-mail: chenmj@hit.edu.cn, E-mail: chowdhury.24@osu.edu [Department of Physics, The Ohio State University, 191 W. Woodruff Ave, Columbus, OH 43210 (United States)

    2016-03-15

    Rapid growth and ultra-precision machining of large-size KDP (KH{sub 2}PO{sub 4}) crystals with high laser damage resistance are tough challenges in the development of large laser systems. It is of high interest and practical significance to have theoretical models for scientists and manufacturers to determine the laser-induced damage threshold (LIDT) of actually prepared KDP optics. Here, we numerically and experimentally investigate the laser-induced damage on KDP crystals in ultra-short pulse laser regime. On basis of the rate equation for free electron generation, a model dedicated to predicting the LIDT is developed by considering the synergistic effect of photoionization, impact ionization and decay of electrons. Laser damage tests are performed to measure the single-pulse LIDT with several testing protocols. The testing results combined with previously reported experimental data agree well with those calculated by the model. By taking the light intensification into consideration, the model is successfully applied to quantitatively evaluate the effect of surface flaws inevitably introduced in the preparation processes on the laser damage resistance of KDP crystals. This work can not only contribute to further understanding of the laser damage mechanisms of optical materials, but also provide available models for evaluating the laser damage resistance of exquisitely prepared optical components used in high power laser systems.

  12. A Novel Schiff Base of 3-acetyl-4-hydroxy-6-methyl-(2Hpyran-2-one and 2,2'-(ethylenedioxydiethylamine as Potential Corrosion Inhibitor for Mild Steel in Acidic Medium

    Directory of Open Access Journals (Sweden)

    Jonnie N. Asegbeloyin

    2015-05-01

    Full Text Available The corrosion inhibition activity of a newly synthesized Schiff base (SB from 3-acetyl-4-hydroxy-6-methyl-(2H-pyran-2-one and 2,2'-(ethylenedioxydiethylamine was investigated on the corrosion of mild steel in 1 M HCl solution using potentiodynamic polarization and electrochemical impedance spectroscopic techniques. Ultraviolet-visible (UV-vis and Raman spectroscopic techniques were used to study the chemical interactions between SB and mild steel surface. SB was found to be a relatively good inhibitor of mild steel corrosion in 1 M HCl. The inhibition efficiency increases with increase in concentration of SB. The inhibition activity of SB was ascribed to its adsorption onto mild steel surface, through physisorption and chemisorption, and described by the Langmuir adsorption model. Quantum chemical calculations indicated the presence of atomic sites with potential nucleophilic and electrophilic characteristics with which SB can establish electronic interactions with the charged mild steel surface.

  13. Corrosion inhibition of carbon steel XC70 in H 2 SO 4 solution by ...

    African Journals Online (AJOL)

    In this work, we studied the efficiency of corrosion inhibition of carbon steel XC70 in H2SO4 0.5 M aqueous solution using ferrocenyl derivatives synthesized in our laboratory, this compound is: 3-(ferrocenylmethylamine)benzonitrile. The inhibitory potential of this compound was determined by electrochemical techniques ...

  14. Inhibitor for the Corrosion of Mild Steel in H 2 SO 4 | Patel | South ...

    African Journals Online (AJOL)

    An extract of Terminalia chebula fruits was investigated as a corrosion inhibitor of mild steel in 0.5 M H2SO4 by means of conventional mass loss, electrochemical polarization, electrochemical impedance spectroscopy and scanning electron microscopy. The mass loss results showed that the extract of Terminalia chebula is ...

  15. Residual stress relief in MAG welded joints of dissimilar steels

    International Nuclear Information System (INIS)

    Seodek, P.; Brozda, J.; Wang, L.; Withers, P.J.

    2003-01-01

    This paper addresses the relief of residual stress in welded joints between austenitic and non-alloyed ferritic-pearlitic steels. A series of similar and dissimilar steel joints based on the 18G2A (ferritic-pearlitic) and 1H18N10T (austenitic) steels were produced, some of which were stress relieved by annealing and some by mechanical prestressing. For the as-welded and stress relieved test joints the residual stresses were measured by trepanning. To aid the interpretation of these results, 2D plane stress finite element analysis has been performed to simulate the residual stress relieving methods. Analysis of the results has shown that thermal stress relieving of welded joints between dissimilar steels is not effective and may even increase residual stresses, due to the considerable difference in thermal expansion of the joined steels. It was found that, for the loads imposed, the effectiveness of the mechanical stress relieving of dissimilar steel welded joints was much lower than that of similar steel joints

  16. Biological N2 fixation mainly controlled by Sphagnum tissue N:P ratio in ombrotrophic bogs

    Science.gov (United States)

    Zivkovic, Tatjana; Moore, Tim R.

    2017-04-01

    Most of the 18 Pg nitrogen (N) accumulated in northern nutrient-poor and Sphagnum-dominated peatlands (bogs and fens) can be attributed to N2-fixation by diazotrophs either associated with the live Sphagnum or non-symbiotically in the deeper peat such as through methane consumption close to the water table. Where atmospheric N deposition is low (Sphagnum, suggested by the increase in tissue N:P to >16. It is unclear how Sphagnum-hosted diazotrophic activity may be affected by N deposition and thus changes in N:P ratio. First, we investigated the effects of long-term addition of different sources of nitrogen (0, 1.6, 3.2 and 6.4 g N m-2 y-1as NH4Cl and NaNO3), and phosphorus (5 g P m-2 y-1as KH2PO4) on Sphagnum nutrient status (N, P and N:P ratio), net primary productivity (NPP) and Sphagnum-associated N2fixation at Mer Bleue, a temperate ombrotrophic bog. We show that N concentration in Sphagnum tissue increased with larger rates of N addition, with a stronger effect on Sphagnum from NH4 than NO3. The addition of P created a 3.5 fold increase in Sphagnum P content compared to controls. Sphagnum NPP decreased linearly with the rise in N:P ratio, while linear growth declined exponentially with increase in Sphagnum N content. Rates of N2-fixation determined in the laboratory significantly decreased in response to even the smallest addition of both N species. In contrast, the addition of P increased N2 fixation by up to 100 times compared to N treatments and up to 5-30 times compared to controls. The change in N2-fixation was best modeled by the N:P ratio, across all experimental treatments. Secondly, to test the role of N:P ratio on N2-fixation across a range of bogs, eight study sites along the latitudinal gradient from temperate, boreal to subarctic zone in eastern Canada were selected. From each bog, two predominant microptopographies, hummocks and hollows, were tested for both N2-fixation activity in the laboratory and Sphagnum tissue concentrations of N, P and N

  17. Identification and biochemical analysis of Slac2-c/MyRIP as a Rab27A-, myosin Va/VIIa-, and actin-binding protein.

    Science.gov (United States)

    Kuroda, Taruho S; Fukuda, Mitsunori

    2005-01-01

    Slac2-c/MyRIP is a specific Rab27A-binding protein that contains an N-terminal synaptotagmin-like protein (Slp) homology domain (SHD, a newly identified GTP-Rab27A-binding motif), but in contrast to the Slp family proteins, it lacks C-terminal tandem C2 domains. In vitro Slac2-c simultaneously directly interacts with both Rab27A and an actin-based motor protein, myosin Va, via its N-terminal SHD and middle region, respectively, consistent with the fact that the overall structure of Slac2-c is similar to that of Slac2-a/melanophilin, a linker protein between Rab27A and myosin Va in the melanosome transport in melanocytes. Unlike Slac2-a, however, the middle region of Slac2-c interacts with two types of myosins, myosin Va and myosin VIIa. In addition, the most C-terminal part of both Slac2-a and Slac2-c functions as an actin-binding domain: it directly interacts with globular and fibrous actin in vitro, and the actin-binding domain of Slac2-a and Slac2-c colocalizes with actin filaments when it is expressed in living cells (i.e., PC12 cells and mouse melanocytes). In this chapter we describe the methods that have been used to analyze the protein-protein interactions of Slac2-c, specifically with Rab27A, myosin Va/VIIa, and actin.

  18. Pr4N2S3 and Pr4N2Se3: two non-isostructural praseodymium(iii) nitride chalcogenides

    International Nuclear Information System (INIS)

    Lissner, Falk; Schleid, Thomas

    2005-01-01

    The non-isostructural nitride chalcogenides of praseodymium, Pr 4 N 2 S 3 and Pr 4 N 2 Se 3 , are formed by the reaction of the praseodymium metal with sodium azide (NaN 3 ), praseodymium trihalide (PrX 3 ; X = Cl, Br, I) and the respective chalcogen (sulfur or selenium) at 900 C in evacuated silica ampoules after seven days. Both crystallize monoclinically in space group C2/c (Pr 4 N 2 S 3 : a = 1788.57(9), b = 986.04(5), c = 1266.49(6) pm, β = 134.546(7) , Z = 8; Pr 4 N 2 Se 3 : a = 1311.76(7), b = 1017.03(5), c = 650.42(3) pm, β = 90.114(6) , Z = 4). The crystal structures of both compounds show a layered construction, dominated by N 3- -centred (Pr 3+ ) 4 tetrahedra which share a common edge first. Continuing linkage of the so resulting bitetrahedral [N 2 Pr 6 ] 12+ units via the non-connected vertices to layers according to [stack ∞ 2 ]{[N(Pr) 2/2 e (Pr') 2/2 v ] 3+ } forms different kinds of tetrahedral nets which can be described as layers consisting of ''four- and eight-rings'' for Pr 4 N 2 S 3 and as layers of ''six-rings'' for Pr 4 N 2 Se 3 . Whereas the crystal structure of Pr 4 N 2 S 3 exhibits four different Pr 3+ cations with coordination numbers of six (2 x) and seven (2 x) against N 3- and S 2- , the number of cations in the nitride selenide (Pr 4 N 2 Se 3 ) is reduced to half (Pr1 and Pr2) also having six- and sevenfold anionic coordination spheres. Further motifs for the connection of [NM 4 ] 9+ tetrahedra in crystal structures of nitride chalcogenides and halides of the rare-earth elements with ratios of N: M = 1: 2 are presented and discussed. (Abstract Copyright [2005], Wiley Periodicals, Inc.) [de

  19. MTS-MD of Biomolecules Steered with 3D-RISM-KH Mean Solvation Forces Accelerated with Generalized Solvation Force Extrapolation.

    Science.gov (United States)

    Omelyan, Igor; Kovalenko, Andriy

    2015-04-14

    We developed a generalized solvation force extrapolation (GSFE) approach to speed up multiple time step molecular dynamics (MTS-MD) of biomolecules steered with mean solvation forces obtained from the 3D-RISM-KH molecular theory of solvation (three-dimensional reference interaction site model with the Kovalenko-Hirata closure). GSFE is based on a set of techniques including the non-Eckart-like transformation of coordinate space separately for each solute atom, extension of the force-coordinate pair basis set followed by selection of the best subset, balancing the normal equations by modified least-squares minimization of deviations, and incremental increase of outer time step in motion integration. Mean solvation forces acting on the biomolecule atoms in conformations at successive inner time steps are extrapolated using a relatively small number of best (closest) solute atomic coordinates and corresponding mean solvation forces obtained at previous outer time steps by converging the 3D-RISM-KH integral equations. The MTS-MD evolution steered with GSFE of 3D-RISM-KH mean solvation forces is efficiently stabilized with our optimized isokinetic Nosé-Hoover chain (OIN) thermostat. We validated the hybrid MTS-MD/OIN/GSFE/3D-RISM-KH integrator on solvated organic and biomolecules of different stiffness and complexity: asphaltene dimer in toluene solvent, hydrated alanine dipeptide, miniprotein 1L2Y, and protein G. The GSFE accuracy and the OIN efficiency allowed us to enlarge outer time steps up to huge values of 1-4 ps while accurately reproducing conformational properties. Quasidynamics steered with 3D-RISM-KH mean solvation forces achieves time scale compression of conformational changes coupled with solvent exchange, resulting in further significant acceleration of protein conformational sampling with respect to real time dynamics. Overall, this provided a 50- to 1000-fold effective speedup of conformational sampling for these systems, compared to conventional MD

  20. Comparative study between two austenitic steels with the EPR (Electrochemical Potentiokinetic Reactivation) technique

    International Nuclear Information System (INIS)

    Guillen M, A.N.

    1997-01-01

    In the mid 19704s, the intergranular corrosion with stress corrosion cracking (IGSCC) have been identified as a greater problem in Boiling Water Reactors BWR in several places of the world. The Electrochemical Potentiokinetic Reactivation - Single Loop (EPR-SL) test and the Double Loop (EPR-DL) test, were developed as methods for measuring the Degree of Sensitization (DOS), show sensitised materials at subject to Intergranular Corrosion. In Mexico, the Laguna Verde4s reactor is BWR type and many of its principal components was built with AISI 304 stainless steels, while that in VVER reactors as well as Juragua4s reactor in Cuba is used 321 Stainless stell in its Russian equivalent designation 08Ch18N10T. In this work, were studied 304 and 08Ch18N10T stainless steels by means of EPR-SL, EPR-DL and ASTM A-262 techniques, they have been found a good correlation for 304 steel but not in 08Ch18N10T steel and was proposed one modification in the criterion by the evaluation on the sensitisation in this steels. Finally, both materials were welded with procedures used in the nuclear industry, by Slow Strain Rate Test (SSRT) to determine the Stress Corrosion Cracking SCC susceptibility, and subsequently the susceptibility to localized corrosion was studied by means of Cyclic Polarization test and the uniform corrosion rate in a solution with chlorides by the Tafel plot, Potentiodynamic Anodic Polarization Resistance. (Author)

  1. Microstructure of reactive synthesis TiC/Cr18Ni8 stainless steel bonded carbides

    Institute of Scientific and Technical Information of China (English)

    Jiang Junsheng; Liu Junbo; Wang Limei

    2008-01-01

    TiC/Cr18Ni8 steel bonded carbides were synthesized by vacuum sintering with mixed powders of iron, ferrotitanium, ferrochromium, colloidal graphite and nickel as raw materials. The microstructure and microhardness of the steel bonded carbides were analyzed by scanning electron microscope (SEM),X-ray diffraction (XRD) and Rockwell hardometer. Results show that the phases of steel bonded carbides mainly consist of TiC and Fe-Cr-Ni solid solution. The synthesized TiC particles are fine. Most of them are not more than 1 μm With the increase of sintering temperature, the porosity of TiC/Cr18Ni8 steel bonded carbides decreases and the density and hardness increase, but the size of TiC panicles slightly increases. Under the same sintering conditions, the density and hardness of steel bonded carbides with C/Ti atomic ratio 0.9 are higher than those with C/Ti atomic ratio 1.0.The TiC particles with C/Ti atomic ratio 0.9 are much finer and more homogeneous.

  2. The results of studies on clinical dosemeters type VA-J-18. Pt.1

    International Nuclear Information System (INIS)

    Penchev, V.; Buchakliev, Z.; Popits, R.; Konstantinov, B.

    1982-01-01

    A description is submitted of standard instruments used to detect and measure exposure to low and medium energy X-ray and gamma rays ( 137 Cs and 60 Co), designed for the control and calibration of dosimeters. The studies performed on clinical dosimeters, type VA-J-18, are reported. To secure exact exposure measurement, correction coefficients for non-linearity of the readings and for inaccuracy of the range factors are introduced. Non-linearity does not exceed 5 per cent of the begining of the scale, and in the range 30 to 100 scale divisions, it is within the +- 1 per cent limits. Usually, the inaccuracy of the range factors amounts to +- 3 per cent, but in isolated cases it may reach up to 10 per cent, and for that reason the second correction coefficient should be introduced as a routine in all measurements. (author)

  3. Effect of microbial treatment on the prevention and removal of paraffin deposits on stainless steel surfaces.

    Science.gov (United States)

    Xiao, Meng; Li, Wen-Hong; Lu, Mang; Zhang, Zhong-Zhi; Luo, Yi-Jing; Qiao, Wei; Sun, Shan-Shan; Zhong, Wei-Zhang; Zhang, Min

    2012-11-01

    In this study, biosurfactant-producing strain N2 and non-biosurfactant producing stain KB18 were used to investigate the effects of microbial treatment on the prevention and removal of paraffin deposits on stainless steel surfaces. Strain N2, with a biosurfactant production capacity, reduced the contact angle of stainless steel to 40.04°, and the corresponding adhesion work of aqueous phase was decreased by 26.5 mJ/m(2). By contrast, KB18 could only reduce the contact angle to 50.83°, with a corresponding 7.6 mJ/m(2) decrease in the aqueous phase work adhesion. The paraffin removal test showed that the paraffin removal efficiencies of strain N2 and KB18 were 79.0% and 61.2%, respectively. Interestingly, the N2 cells could attach on the surface of the oil droplets to inhibit droplets coalescence. These results indicate that biosurfactant-producing strains can alter the wettability of stainless steel and thus eliminate paraffin deposition. Copyright © 2012 Elsevier Ltd. All rights reserved.

  4. Study of TiC+TiN Multiple Films On Type of 316L Stainless Steel

    Institute of Scientific and Technical Information of China (English)

    XUEQi; JINYong; HUDong-ping; HUANGBen-sheng; DENGBai-quan

    2004-01-01

    In this paper, the synthesis process of TiC+TiN multiple films on super-low-carbon stainless steels is reported. The TiC layer is coated as the first layer in the multiple film, the change of growth rate of the film on the 316L Stainlesss teel is not same as the one on carbides substrates, while the mole ratio of CH4 to TiCl4 (mCH4/TiCl4) is changed from 1.2 to 2.0. The Ti [C,N], as a kind of inter-layer between TiC and TiN layers, is helpful to improve the adhesion hetween the TiC and TiN layer. The cooling rate greatly influences the quality of the adhesion between the TiC+TiN film and substrates.

  5. High-cycle fatigue characteristics of weldable steel for light-water reactors

    International Nuclear Information System (INIS)

    Klesnil, M.; Polak, J.; Obrtlik, K.; Troshchenko, V.T.; Mishchenko, Yu.I.; Khamaza, L.A.

    1982-01-01

    Czechoslovak and Soviet 15Kh2NMFA steel was used for running fatigue tests at temperatures of 20, 350 and 400 degC in the high-cycle range with various loading regimes. The results show that at the given temperatures in this type of steel a cyclic softening occurs. The fatigue characteristics were measured with great dispersion of results, but within this dispersion they are almost identical for various steels at the same temperature. Increased temperature results in the decrease in the amplitude of cyclic deformation stress and in the increase in the amplitude of plastic deformation. The diversity in the values of cyclic plasticity and stress response measured in the given mode may be explained by the lower level of softening and the non-homogeneous cyclic plastic deformation of material under the given constant conditions. (J.B.)

  6. The uranium(VI) oxoazides [UO{sub 2}(N{sub 3}){sub 2}.CH{sub 3}CN], [(bipy){sub 2}(UO{sub 2}){sub 2}(N{sub 3}){sub 4}], [(bipy)UO{sub 2}(N{sub 3}){sub 3}]{sup -}, [UO{sub 2}(N{sub 3}){sub 4}]{sup 2-}, and [(UO{sub 2}){sub 2}(N{sub 3}){sub 8}]{sup 4-}

    Energy Technology Data Exchange (ETDEWEB)

    Haiges, Ralf; Christe, Karl O. [Loker Hydrocarbon Research Institute and Department of Chemistry, University of Southern California, Los Angeles, CA (United States); Vasiliu, Monica; Dixon, David A. [Department of Chemistry, The University of Alabama, Tuscaloosa, AL (United States)

    2017-01-12

    The reaction between [UO{sub 2}F{sub 2}] and an excess of Me{sub 3}SiN{sub 3} in acetonitrile solution results in fluoride-azide exchange and the uranium(VI) dioxodiazide adduct [UO{sub 2}(N{sub 3}){sub 2}.CH{sub 3}CN] was isolated in quantitative yield. The subsequent reaction of [UO{sub 2}(N{sub 3}){sub 2}.CH{sub 3}CN] with 2,2{sup '}-bipyridine (bipy) resulted in the formation of the azido-bridged binuclear complex [(bipy){sub 2}(UO{sub 2}){sub 2}(N{sub 3}){sub 4}]. The triazido anion [(bipy)UO{sub 2}(N{sub 3}){sub 3}]{sup -} was obtained by the reaction of [UO{sub 2}(N{sub 3}){sub 2}.CH{sub 3}CN] with stoichiometric amounts of bipy and the ionic azide [PPh{sub 4}][N{sub 3}]. The reaction of [UO{sub 2}(N{sub 3}){sub 2}] with two equivalents of the [PPh{sub 4}][N{sub 3}] resulted in the formation of the mononuclear tetraazido anion [UO{sub 2}(N{sub 3}){sub 4}]{sup 2-} as well as the azido-bridged binuclear anion [(UO{sub 2}){sub 2}(N{sub 3}){sub 8}]{sup 4-}. The novel uranium oxoazides were characterized by their vibrational spectra and in the case of [(bipy){sub 2}(UO{sub 2}){sub 2}(N{sub 3}){sub 4}].CH{sub 3}CN, [PPh{sub 4}][(bipy)UO{sub 2}(N{sub 3}){sub 3}], [PPh{sub 4}]{sub 2}[UO{sub 2}(N{sub 3}){sub 4}], [PPh{sub 4}]{sub 2}[UO{sub 2}(N{sub 3}){sub 4}].2CH{sub 3}CN, and [PPh{sub 4}]{sub 4}[(UO{sub 2}){sub 2}(N{sub 3}){sub 8}].4CH{sub 3}CN by their X-ray crystal structures. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

  7. Isatin derivatives as a non-toxic corrosion inhibitor for mild steel in 20% H2SO4

    International Nuclear Information System (INIS)

    Ansari, K.R.; Quraishi, M.A.; Singh, Ambrish

    2015-01-01

    Highlights: • Mild steel protection in 20% H 2 SO 4 by TZs. • Potentiodynamic polarization curves reveal that the actions of TZs are mixed type but cathodically predominant. • The adsorption of TZs obeys the Langmuir adsorption isotherm. • Examination of surface morphology by SEM and EDX. • Correlation between experimental and quantum chemical results. - Abstract: The corrosion inhibition action of Isatin-β-thiosemicarbzone derivatives namely 1-Benzylidene-5-(2-oxoindoline-3-ylidene) Thiocarbohydrazone (TZ-1) and 1-(4-Methylbenzylidene)-5-(2-oxoindolin-3-ylidene) Thiocarbohydrazone (TZ-2) was studied on mild steel surface in 20% H 2 SO 4 by gravimetric measurements, Electrochemical measurements (EIS and Tafel), SEM, EDX and quantum chemical methods. Potentiodynamic polarization curves reveal that the TZs act as mixed type inhibitors exhibiting predominantly cathodic behavior. The adsorption of TZs obeys the Langmuir adsorption isotherm. The thermodynamic parameters (E a , K ads , ΔG° ads ) were also computed and discussed

  8. Effect of elemental composition of ion beam on the phase formation and surface strengthening of structural materials

    International Nuclear Information System (INIS)

    Avdienko, K.I.; Avdienko, A.A.; Kovalenko, I.A.

    2001-01-01

    The investigation results are reported on the influence of ion beam element composition on phase formation, wear resistance and microhardness of surface layers of titanium alloys VT-4 and VT-16 as well as stainless steel 12Kh18N10T implanted with nitrogen, oxygen and boron. It is stated that ion implantation into structural materials results in surface hardening and is directly dependent on element composition of implanted ion beam. The presence of oxygen in boron or nitrogen ion beams prevents the formation of boride and nitride phases thus decreasing a hardening effect [ru

  9. Cause of death during 2009–2012, using a probabilistic model (InterVA-4: an experience from Ballabgarh Health and Demographic Surveillance System in India

    Directory of Open Access Journals (Sweden)

    Sanjay K. Rai

    2014-10-01

    Full Text Available Objectives: The present study aimed to estimate the age and cause-specific mortality in Ballabgarh Health and Demographic Surveillance System (HDSS site for the years 2009 to 2012, using a probabilistic model (InterVA-4. Methods: All Deaths in Ballabgarh HDSS from January 1, 2009, to December 31, 2012, were included in the study. InterVA-4 model (version 4.02 was used for assigning cause of death (COD. Data from the verbal autopsy (VA tool were extracted and processed with the InterVA-4 model. Cause-specific mortality rate (CSMR per 1,000 person-years was calculated. Results: A total of 2,459 deaths occurred in the HDSS during the year 2009 to 2012. Among them, 2,174 (88.4% valid VA interviews were conducted. Crude death rate ranged from 7.1 (2009 to 6.4 (2012 per 1,000 population. The CSMR per 1,000 person-years over the years (2009–2012 for non-communicable diseases, communicable diseases, trauma, neoplasm, and maternal and neonatal diseases were 1.78, 1.68, 0.68, 0.49, and 0.48, respectively. The most common causes of death among children, adults, and the elderly were infectious diseases, trauma, and non-communicable diseases, respectively. Conclusions: Overall, non-communicable diseases constituted the largest proportion of mortality, whereas trauma was the most common COD among adults at Ballabgarh HDSS. Policy-makers ought to focus on prevention of premature CODs, especially prevention of infectious diseases in children, and intentional self-harm and road traffic accidents in the adult population.

  10. Brand-Name Prescription Drug Use Among Diabetes Patients in the VA and Medicare Part D: A National Comparison

    Science.gov (United States)

    Gellad, Walid F.; Donohue, Julie M.; Zhao, Xinhua; Mor, Maria K.; Thorpe, Carolyn T.; Smith, Jeremy; Good, Chester B.; Fine, Michael J.; Morden, Nancy E.

    2013-01-01

    Background Medicare Part D and the Department of Veterans Affairs (VA) use different approaches to manage prescription drug benefits, with implications for spending. Medicare relies on private plans with distinct formularies, whereas VA administers its own benefit using a national formulary. Objective To compare overall and regional rates of brand-name drug use among older adults with diabetes in Medicare and VA. Design Retrospective cohort Setting Medicare and VA Patients National sample in 2008 of 1,061,095 Part D beneficiaries and 510,485 Veterans age 65+ with diabetes. Measurements Percent of patients on oral hypoglycemics, statins, and angiotensin-converting-enzyme inhibitors/angiotensin-receptor-blockers who filled brand-name drugs and percent of patients on long-acting insulin who filled analogues. We compared sociodemographic and health-status adjusted hospital referral region (HRR) brand-name use to examine local practice patterns, and calculated changes in spending if each system’s brand-name use mirrored the other. Results Brand-name use in Medicare was 2–3 times that of VA: 35.3% vs. 12.7% for oral hypoglycemics, 50.7% vs. 18.2% for statins, 42.5% vs. 20.8% for angiotensin-converting-enzyme inhibitors/angiotensin-receptor-blockers, and 75.1% vs. 27.0% for insulin analogues. Adjusted HRR brand-name statin use ranged (5th to 95th percentile) from 41.0%–58.3% in Medicare and 6.2%–38.2% in VA. For each drug group, the HRR at the 95th percentile in VA had lower brand-name use than the 5th percentile HRR in Medicare. Medicare spending in this population would have been $1.4 billion less if brand-name use matched the VA for these medications. Limitation This analysis cannot fully describe the factors underlying differences in brand-name use. Conclusions Medicare beneficiaries with diabetes use 2–3 times more brand-name drugs than a comparable group within VA, at substantial excess cost. Primary Funding Sources VA; NIH; RWJF PMID:23752663

  11. μ-4,4′-Bipyridine-κ2N:N′-bis[aqua(4,4′-bipyridine-κN(l-valinato-κ2N,Ocopper(II] dinitrate dihydrate

    Directory of Open Access Journals (Sweden)

    Mao-Chun Hong

    2008-02-01

    Full Text Available In the title dinuclear complex, [Cu2(C5H10NO22(C10H8N23(H2O2](NO32·2H2O, each of the two l-valinate anions chelates a CuII center through the amino N and carboxylate O atom, forming a five-membered ring. A 4,4′-bipyridine molecule bridges two water-coordinated Cu atoms, each of which is connected to another 4,4′-bipyridine, giving rise to a square-pyramidal coordination geometry for the CuII centers. The dinuclear dications, nitrate anions and uncoordinated water molecules are linked into a two-dimensional structure.

  12. Mechanical properties of permeable materials with an organized structure on the base of continuous metal fibers

    International Nuclear Information System (INIS)

    Karpinos, D.M.; Rutkovskij, A.E.; Zorin, V.A.; Ivanchuk, A.A.

    1979-01-01

    The mechanical properties were studied for permeable fibrous materials with an organized structure on the base of continuous metal fibers (from Kh18N9T steel) subjected to preliminary reprocessing volumetric net half-finished products. The effect of geometrical parameters of the net half-finished products and of their orientation in packing are shown to affect the mechanical properties within a wide range of porosities

  13. The temperature dependences of the N2+ + N2N4+ and O2+ + O2 → O4+ association reactions

    International Nuclear Information System (INIS)

    Boehringer, H.; Arnold, F.; Smith, D.; Adams, N.G.

    1983-01-01

    The temperature dependencies of three body association reactions have been investigated in attempts to elucidate the mechanisms of ion-molecule association. The variation with temperature of the three-body rate coefficients is described usually as a power law k approximately Tsup(-n). Experience has shown that with measurements over limited temperature ranges as with previous methods the derived coefficients n are wrong and measurements over large temperature ranges are desirable. The selected ion flow-tube and the drift tube methods developed in Birmingham and Heidelberg provide measurements over (overlapping) wide temperature rang. In collaboration of the Birmingham and the Heidelberg group the He stabilized reactions N 2 + + N 2 + He → N 4 + + He and O 2 + + O 2 + He → O 4 + + He reactions over 30 to 600 deg K. A power law dependence is found above 100 K. The temperature dependencies of the rate constants are interpred and used as a critical test of recent theories of association reactions by D.R. Bates and E. Herbst. (G.Q.)

  14. (2,3,7,8,12,13,17,18-Octaethylporphyrinato-κ4Ncobalt(II–2-nitrobenzaldehyde (1/2

    Directory of Open Access Journals (Sweden)

    Anissa Mansour

    2012-09-01

    Full Text Available The asymmetric unit of the title compound, [Co(C36H44N42C7H5NO3, is composed of one half of the complex, arranged about an inversion center, and a complete 2-nitrobenzaldehyde (NBA molecule. The structure consists of columns that contain interleaved molecules of NBA and [CoII(OEP] (OEP is 2,3,7,8,12,13,17,18-octaethylporphyrin, which are stacked along the a axis. The CoII atom is involved in a π interaction with the ring of the NBA molecule with a centroid–metal distance of 3.508 (6 Å. There is an intramolecular C—H...O hydrogen bond in the NBA molecule.

  15. Crystal structure of [tris(pyridin-2-ylmethyl)amine-κ4N]copper(II) bromide

    OpenAIRE

    Emma C. Bridgman; Megan M. Doherty; Kaleigh A. Ellis; Elizabeth A. Homer; Taylor N. Lashbrook; Margaret E. Mraz; Gina C. Pernesky; Emma M. Vreeke; Kayode D. Oshin; Allen G. Oliver

    2016-01-01

    In the asymmetric unit of the title compound, [CuBr(C18H18N4)]Br, there are three crystallographically independent cations. One of the cations exhibits positional disorder of the pyridin-2-yl?methyl groups over two sets of sites with refined occupancies of 0.672?(8) and 0.328?(8). The outer-sphere bromine counter-ion is severely disordered over multiple sites. In each cation, the CuII ion is coordinated by the four N atoms of the tris?(pyridin-2-ylmeth?yl)amine ligand and one bromine and adop...

  16. Creep-fatigue behavior of 2 1/4Cr-1Mo steel at 5500C in air and vacuum

    International Nuclear Information System (INIS)

    Asayama, T.; Cheng, S.Z.; Asada, Y.; Mitsuhashi, S.; Tachibana, Y.

    1987-01-01

    Following studies on creep-fatigue behaviors of 304 steel at 650 0 C (Asada et al (1980) and Morishita et al (1984), (1985), (1987)), 2 1/4Cr-1Mo steel was studied on its creep-fatigue behaviors at 550 0 C in air and vacuum of 100 and 0.1 μPa. The present study intends to give a base for an evaluation of the environmental effect through obtaining a pure creep-fatigue behavior of this steel which is free from the environmental effect. In the previous studies on 304 steel, tests were conducted in three kinds of environment of air, 100 and 0.1 μPa vacuum. It seemed to be plausible that the 0.1 μPa vacuum shows the pure creep-fatigue behavior of 304 steel at 650 0 C which is almost completely free from the environment. A creep-fatigue life in 0.1 μPa vacuum is almost one order of magnitude higher than that in air. The 100 μPa vacuum suggested that the environmental effect of air still remains but is so small that a creep-fatigue life in 100 μPa is same to that in 0.1 μPa in some strain wave forms. The present study intends to examine if similar observations are obtained with 2 1/4Cr-1Mo steel at 550 0 C. This paper describes the analysis of the overstress and damages, in addition to a creep-fatigue result. (orig.GL)

  17. Depth profiling of {sup 14} N and {sup 20} Ne implantation into iron and steel using(p, gamma) reactions. Vol. 2

    Energy Technology Data Exchange (ETDEWEB)

    Wriekat, A; Haj-Abdellah, M [Physics Department, University of Jordan, Amman (Jordan)

    1996-03-01

    Depth profiles of {sup 14} N and {sup 20} Ne ions at 800 KeV implanted into iron and by steel samples have been measured by means of the proton induced {gamma}- ray emission (Pige) technique. The range, R, and range straggling, {Delta}R for these profiles were obtained and compared with theoretical calculations. The experimental results did show that pure iron retains more N and Ne than steel. 2 figs., 1 tab.

  18. Thermodynamics of complex structures formed between single-stranded DNA oligomers and the KH domains of the far upstream element binding protein

    Energy Technology Data Exchange (ETDEWEB)

    Chakraborty, Kaushik; Sinha, Sudipta Kumar; Bandyopadhyay, Sanjoy, E-mail: sanjoy@chem.iitkgp.ernet.in [Molecular Modeling Laboratory, Department of Chemistry, Indian Institute of Technology, Kharagpur 721302 (India)

    2016-05-28

    The noncovalent interaction between protein and DNA is responsible for regulating the genetic activities in living organisms. The most critical issue in this problem is to understand the underlying driving force for the formation and stability of the complex. To address this issue, we have performed atomistic molecular dynamics simulations of two DNA binding K homology (KH) domains (KH3 and KH4) of the far upstream element binding protein (FBP) complexed with two single-stranded DNA (ss-DNA) oligomers in aqueous media. Attempts have been made to calculate the individual components of the net entropy change for the complexation process by adopting suitable statistical mechanical approaches. Our calculations reveal that translational, rotational, and configurational entropy changes of the protein and the DNA components have unfavourable contributions for this protein-DNA association process and such entropy lost is compensated by the entropy gained due to the release of hydration layer water molecules. The free energy change corresponding to the association process has also been calculated using the Free Energy Perturbation (FEP) method. The free energy gain associated with the KH4–DNA complex formation has been found to be noticeably higher than that involving the formation of the KH3–DNA complex.

  19. Inhibition by Ginkgo leaves extract of the corrosion of steel in HCl and H{sub 2}SO{sub 4} solutions

    Energy Technology Data Exchange (ETDEWEB)

    Deng Shuduan, E-mail: dengshuduan@163.com [Faculty of Materials Engineering, Southwest Forestry University, Kunming 650224 (China); Li Xianghong [Faculty of Science, Southwest Forestry University, Kunming 650224 (China)

    2012-02-15

    Highlights: Black-Right-Pointing-Pointer Ginkgo leaves extract (GLE) acts as a good inhibitor for steel in HCl and H{sub 2}SO{sub 4} media. Black-Right-Pointing-Pointer The inhibition efficiency follows the order: HCl > H{sub 2}SO{sub 4}. Black-Right-Pointing-Pointer The adsorption of GLE on steel surface obeys Langmuir adsorption isotherm. Black-Right-Pointing-Pointer GLE behaves as a mixed-type inhibitor in 1.0 M HCl, while cathodic inhibitor in 0.5 M H{sub 2}SO{sub 4}. - Abstract: The inhibition effect of Ginkgo leaves extract (GLE) on the corrosion of cold rolled steel (CRS) in 1.0-5.0 M HCl and 0.5-2.5 M H{sub 2}SO{sub 4} solutions was investigated for the first time by weight loss, potentiodynamic polarization curves, electrochemical impedance spectroscopy (EIS) and scanning electron microscopy (SEM) methods. The results show that GLE is a good inhibitor, and exhibits more efficient in 1.0 M HCl than 0.5 M H{sub 2}SO{sub 4}. The adsorption of GLE on CRS surface obeys Langmuir adsorption isotherm. GLE acts as a mixed-type inhibitor in 1.0 M HCl, while a cathodic inhibitor in 0.5 M H{sub 2}SO{sub 4}.

  20. 3D ZnIn2S4 nanosheet/TiO2 nanowire arrays and their efficient photocathodic protection for 304 stainless steel

    Science.gov (United States)

    Sun, Wenxia; Wei, Na; Cui, Hongzhi; Lin, Yuan; Wang, Xinzhen; Tian, Jian; Li, Jian; Wen, Jing

    2018-03-01

    A well-designed heterostructure engineered ZnIn2S4 nanosheet/TiO2 nanowire arrays photoanode is investigated for photocathodic protection. The ZnIn2S4 nanosheets are distributed uniformly on the surface of the TiO2 nanowire by a hydrothermal method. The stem-and-leaf-like ZnIn2S4 nanosheet/TiO2 nanowire arrays exhibit excellent photoelectrochemical properties, owing to the energy band structure and large surface area. A maximum photocurrent density of 2 mA cm-2 is achieved for the ZnIn2S4 nanosheet/TiO2 nanowire composite film for a 6 h reaction time under white illumination. Moreover, the potential of the 304 stainless steel coupled with the composite film immediately shifts negatively to -1.17 V (vs. SCE), which is significantly lower than the corrosion potential (-0.201 V vs. SCE). Thus, the composite film offers a superior photocathodic protection for stainless steel against corrosion by a NaCl solution. This study provides a promising approach for the design and synthesis of composite films with enhanced photoelectrochemical performance.