46 CFR 9.10 - Waiting time.

Science.gov (United States)

2010-10-01

... 46 Shipping 1 2010-10-01 2010-10-01 false Waiting time. 9.10 Section 9.10 Shipping COAST GUARD... § 9.10 Waiting time. The same construction should be given the act when charging for waiting time as... for duty the waiting time amounts to at least one hour. ...

Critical role for thymic CD19+CD5+CD1dhiIL-10+ regulatory B cells in immune homeostasis.

Science.gov (United States)

Xing, Chen; Ma, Ning; Xiao, He; Wang, Xiaoqian; Zheng, Mingke; Han, Gencheng; Chen, Guojiang; Hou, Chunmei; Shen, Beifen; Li, Yan; Wang, Renxi

2015-03-01

This study tested the hypothesis that besides the spleen, LNs, peripheral blood, and thymus contain a regulatory IL-10-producing CD19(+)CD5(+)CD1d(high) B cell subset that may play a critical role in the maintenance of immune homeostasis. Indeed, this population was identified in the murine thymus, and furthermore, when cocultured with CD4(+) T cells, this population of B cells supported the maintenance of CD4(+)Foxp3(+) Tregs in vitro, in part, via the CD5-CD72 interaction. Mice homozygous for Cd19(Cre) (CD19(-/-)) express B cells with impaired signaling and humoral responses. Strikingly, CD19(-/-) mice produce fewer CD4(+)Foxp3(+) Tregs and a greater percentage of CD4(+)CD8(-) and CD4(-)CD8(+) T cells. Consistent with these results, transfer of thymic CD19(+)CD5(+)CD1d(hi) B cells into CD19(-/-) mice resulted in significantly up-regulated numbers of CD4(+)Foxp3(+) Tregs with a concomitant reduction in CD4(+)CD8(-) and CD4(-)CD8(+) T cell populations in the thymus, spleen, and LNs but not in the BM of recipient mice. In addition, thymic CD19(+)CD5(+)CD1d(hi) B cells significantly suppressed autoimmune responses in lupus-like mice via up-regulation of CD4(+)Foxp3(+) Tregs and IL-10-producing Bregs. This study suggests that thymic CD19(+)CD5(+)CD1d(hi)IL-10(+) Bregs play a critical role in the maintenance of immune homeostasis. © Society for Leukocyte Biology.

Effect of partial oxygen pressure on physicochemical properties of Kh18N10T steel at isothermal oxidation

International Nuclear Information System (INIS)

Alekseev, V.N.; Oshe, E.K.; Fokin, M.N.; Bogdanova, S.V.; Loskutov, A.I.

1990-01-01

Auger-electron spectroscopy, photoelectric polarization, conductometry methods have been used to analyze chemical and defect composition of surface oxide layers, formed on stainless steel Kh18N10T in vacuum (10 -9 - 10 -2 torr) and at temperatures 593-673 K. The boundary conditions of manifestation of extermal behaviour of the dependence of the surface oxide growth rate at isothermal oxidation of this steel are determined. The relation between passivation properties of the surface oxide and the magnitude of the edge angle of the surface wetting with molten tin is revealed

CD44 standard and CD44v10 isoform expression on leukemia cells distinctly influences niche embedding of hematopoietic stem cells.

Science.gov (United States)

Erb, Ulrike; Megaptche, Amelie Pajip; Gu, Xiaoyu; Büchler, Markus W; Zöller, Margot

2014-03-31

A blockade of CD44 is considered a therapeutic option for the elimination of leukemia initiating cells. However, anti-panCD44 can interfere with hematopoiesis. Therefore we explored, whether a CD44 variant isoform (CD44v)-specific antibody can inhibit leukemia growth without attacking hematopoiesis. As a model we used CD44v10 transfected EL4 thymoma cells (EL4-v10). The therapeutic efficacy of anti-panCD44 and anti-CD44v10 was evaluated after intravenous application of EL4/EL4-v10. Ex vivo and in vitro studies evaluated the impact of anti-panCD44 and anti-CD44v10 as well as of EL4 and EL4-v10 on hematopoietic stem cells (HSC) in cocultures with bone marrow stroma cells with a focus on adhesion, migration, cell cycle progression and apoptosis resistance. Intravenously injected EL4-v10 grow in bone marrow and spleen. Anti-panCD44 and, more pronounced anti-CD44v10 prolong the survival time. The higher efficacy of anti-CD44v10 compared to anti-panCD44 does not rely on stronger antibody-dependent cellular cytotoxicity or on promoting EL4-v10 apoptosis. Instead, EL4 compete with HSC niche embedding. This has consequences on quiescence and apoptosis-protecting signals provided by the stroma. Anti-panCD44, too, more efficiently affected embedding of HSC than of EL4 in the bone marrow stroma. EL4-v10, by catching osteopontin, migrated on bone marrow stroma and did not or weakly interfere with HSC adhesion. Anti-CD44v10, too, did not affect the HSC--bone marrow stroma crosstalk. The therapeutic effect of anti-panCD44 and anti-CD44v10 is based on stimulation of antibody-dependent cellular cytotoxicity. The superiority of anti-CD44v10 is partly due to blocking CD44v10-stimulated osteopontin expression that could drive HSC out of the niche. However, the main reason for the superiority of anti-CD44v10 relies on neither EL4-v10 nor anti-CD44v10 severely interfering with HSC--stroma cell interactions that, on the other hand, are affected by EL4 and anti-panCD44. Anti-panCD44

E-cadherin and CD10 expression in atypical hyperplastic and malignant endometrial lesions

International Nuclear Information System (INIS)

Ahmed, A.R.H.; Muhammad, E.M.S.

2014-01-01

Background: Loss of E-cadherin is a critical step for development and progression of malignant tumors. CD10; a marker of non-neoplastic and neoplastic endometrial stroma, is associated with aggressiveness of many epithelial malignancies. Aims: To evaluate expression and correlation of E-cadherin and CD10 in endometrial lesions and their possible role in differentiating atypical endometrial hyperplasia from endometrial carcinoma. The association of E-cadherin and CD10 expression with clinico-pathological parameters of endometrial carcinoma was also investigated. Materials and methods: Fifty four cases including 28 endometrial carcinomas; 19 endometrial hyperplasia and 7 cases of normal endometrial changes were enrolled for this study. The expression of E-cadherin and CD10 was evaluated by immunohistochemistry using the streptavidin–biotin technique. Results: There was a strong association between malignant change of endometrial glands and membrano- cytoplasmic localization of E-cadherin (p< 0.001). Expression of E-cadherin but not CD10 was significantly higher in endometrial carcinomas compared to atypical endometrial hyperplasia (p < 0.01). Expression of E-cadherin was not associated with CD10 expression in different endometrial lesions. High grade tumors expressed low levels of both E-cadherin (p<0.01) and CD10 (p < 0.05) and serous endometrial carcinoma had low E-cadherin and CD10 expression compared to endometrioid carcinoma (p< 0.01 and <0.05, respectively). Expression of both molecules showed no association with depth of tumor invasion or FIGO stage. Tumors with lower E-cadherin or CD10 expression had higher rates of vascular tumor emboli (p< 0.01 and <0.07, respectively). Conclusions: Although expression of E-cadherin and CD10 in endometrial lesions was not correlated, reduced expression of both molecules could be critical for progression of endometrial carcinoma.

Tissue-specific regulation of CXCL9/10/11 chemokines in keratinocytes: Implications for oral inflammatory disease.

Directory of Open Access Journals (Sweden)

Alison Marshall

Full Text Available The IFN-γ-inducible chemokines CXCL9, CXCL10, and CXCL11 play a key role in many inflammatory conditions, particularly those mediated by T cells. Therefore, the production of these chemokines in peripheral tissues could be instrumental in the pathophysiology of tissue-specific immunological diseases such as oral lichen planus (OLP. In the present study, we assessed the production of keratinocyte-derived CXCL9/10/11 under basal and inflammatory conditions and investigated whether these chemokines were involved in the pathogenesis of OLP. We used semi-quantitative PCR, ELISA, chemotaxis assays, and fluorescence-activated cell sorting (FACS to assess the expression and functional role of CXCL9/10/11 in oral keratinocytes (three strains of normal human oral keratinocytes (NHOK, and the H357 oral cancer cell line in the presence or absence of IFN-γ. CXCL9/10/11 were also assessed in tissues from normal patients and those with oral lichen planus (OLP. The time course study in oral keratinocytes treated with IFN-γ showed that expression of CXCL9/10/11 chemokines was significantly enhanced by IFN-γ in a time-dependent manner. In particular, CXCL10, a prominent chemokine that was overexpressed by IFN-γ-stimulated NHOK, was able to effectively recruit CD4 lymphocytes, mainly CD4+CD45RA- cells. Significantly higher levels of CXCL9/10/11 were found in tissues from patients with OLP compared to normal oral mucosa. Taken together, the results demonstrate that normal oral keratinocytes produce chemotactic molecules that mediate T cell recruitment. This study furthers understanding of chemokine production in oral keratinocytes and their role in the pathophysiology of oral mucosa, with particular relevance to OLP.

Mechanical properties of steel 8 CrMoNiNb 9 10 in dependence on the microstructural condition

International Nuclear Information System (INIS)

Fabritius, H.; Schnabel, E.

1976-01-01

Tension tests at room temperature to 600 0 C and creep-rupture tests at 500 to 600 0 C lasting up to about 75,000 h on two casts of steel 8 CrMoNiNb 9 10 with about 0.08% C, 0.3% Si, 0.7% Mn, 0.012% N, 0.005% Al, 2.34% Cr, 0.95% Mo, 0.8% Nb and 0.64% Ni in bainitic and ferritic microstructural condition. Influence of annealing at 650 to 800 0 C on the properties in the tension test. Influence of aging at 500 to 600 0 C lasting up to 30,000 h with and without mechanical stress on the properties in the tension test at aging temperature and on the toughness behaviour in the notched bar impact bend test at room temperature. (orig.) [de

Passive behaviour of alloy corrosion-resistant steel Cr10Mo1 in simulating concrete pore solutions with different pH

International Nuclear Information System (INIS)

Ai, Zhiyong; Jiang, Jinyang; Sun, Wei; Song, Dan; Ma, Han; Zhang, Jianchun; Wang, Danqian

2016-01-01

Highlights: • A new alloy corrosion-resistant steel Cr10Mo1 is developed for reinforcing rebar of concrete in severe environments. • The effects of pH on the passive behaviour of Cr10Mo1 steel compared with plain carbon steel were studied systematically by electrochemical techniques and surface analysis. • The mechanism for self-reinforcing passivity against carbonation of the corrosion-resistant steel is revealed. - Abstract: The passive behaviour of new alloy corrosion-resistant steel Cr10Mo1 and plain carbon steel (as a comparison) in simulating concrete pore solutions of different pH (ranging from 13.5 to 9.0) under open circuit potential conditions, was evaluated by various electrochemical techniques: potentiodynamic polarization, capacitance measurements and electrochemical impedance spectroscopy. The chemical composition and structure of passive films were investigated by X-ray photoelectron spectroscopy (XPS) and secondary ion mass spectroscopy (SIMS). The electrochemical responses of passive films show that Cr10Mo1 steel has an increasing passivity with pH decreasing while carbon steel dose conversely, revealing carbonation does no negative effect on passivation of the corrosion-resistant steel. SIMS reveals that the passive film on the corrosion-resistant steel presents a bilayer structure: an outer layer mainly consisting of Fe oxides and hydroxides, and an inner layer enriched in Cr species, while only a Fe-concentrated layer for carbon steel. According to the XPS analysis results, as the pH decreases, more stable and protective Cr oxides are enriched in the film on Cr10Mo1 steel while Fe oxides gradually decompose. Higher content of Cr oxides in the film layer provides Cr10Mo1 corrosion-resistant steel more excellent passivity at lower pH.

Passive behaviour of alloy corrosion-resistant steel Cr10Mo1 in simulating concrete pore solutions with different pH

Energy Technology Data Exchange (ETDEWEB)

Ai, Zhiyong, E-mail: 230139452@seu.edu.cn [School of Materials Science and Engineering, Southeast University, Nanjing 211189, Jiangsu (China); Jiangsu Key Laboratory of Construction Materials, Nanjing 211189, Jiangsu (China); Jiang, Jinyang, E-mail: jiangjinyang16@163.com [School of Materials Science and Engineering, Southeast University, Nanjing 211189, Jiangsu (China); Jiangsu Key Laboratory of Construction Materials, Nanjing 211189, Jiangsu (China); Sun, Wei, E-mail: sunwei@seu.edu.cn [School of Materials Science and Engineering, Southeast University, Nanjing 211189, Jiangsu (China); Jiangsu Key Laboratory of Construction Materials, Nanjing 211189, Jiangsu (China); Song, Dan, E-mail: songdancharls@hhu.edu.cn [School of Materials Science and Engineering, Southeast University, Nanjing 211189, Jiangsu (China); Jiangsu Key Laboratory of Construction Materials, Nanjing 211189, Jiangsu (China); College of Mechanics and Materials, Hohai University, Nanjing 210098, Jiangsu (China); Ma, Han, E-mail: mahan-iris@shasteel.cn [Research Institute of Jiangsu Shasteel Iron and Steel, Zhangjiagang 215625, Jiangsu (China); Zhang, Jianchun, E-mail: Zhangjc-iris@shasteel.cn [Research Institute of Jiangsu Shasteel Iron and Steel, Zhangjiagang 215625, Jiangsu (China); Wang, Danqian, E-mail: wonderbaba@126.com [School of Materials Science and Engineering, Southeast University, Nanjing 211189, Jiangsu (China); Jiangsu Key Laboratory of Construction Materials, Nanjing 211189, Jiangsu (China)

2016-12-15

Highlights: • A new alloy corrosion-resistant steel Cr10Mo1 is developed for reinforcing rebar of concrete in severe environments. • The effects of pH on the passive behaviour of Cr10Mo1 steel compared with plain carbon steel were studied systematically by electrochemical techniques and surface analysis. • The mechanism for self-reinforcing passivity against carbonation of the corrosion-resistant steel is revealed. - Abstract: The passive behaviour of new alloy corrosion-resistant steel Cr10Mo1 and plain carbon steel (as a comparison) in simulating concrete pore solutions of different pH (ranging from 13.5 to 9.0) under open circuit potential conditions, was evaluated by various electrochemical techniques: potentiodynamic polarization, capacitance measurements and electrochemical impedance spectroscopy. The chemical composition and structure of passive films were investigated by X-ray photoelectron spectroscopy (XPS) and secondary ion mass spectroscopy (SIMS). The electrochemical responses of passive films show that Cr10Mo1 steel has an increasing passivity with pH decreasing while carbon steel dose conversely, revealing carbonation does no negative effect on passivation of the corrosion-resistant steel. SIMS reveals that the passive film on the corrosion-resistant steel presents a bilayer structure: an outer layer mainly consisting of Fe oxides and hydroxides, and an inner layer enriched in Cr species, while only a Fe-concentrated layer for carbon steel. According to the XPS analysis results, as the pH decreases, more stable and protective Cr oxides are enriched in the film on Cr10Mo1 steel while Fe oxides gradually decompose. Higher content of Cr oxides in the film layer provides Cr10Mo1 corrosion-resistant steel more excellent passivity at lower pH.

Dechlorination and chlorine rearrangement of 1,2,5,5,6,9,10-heptachlorodecane mediated by the whole pumpkin seedlings.

Science.gov (United States)

Li, Yanlin; Hou, Xingwang; Yu, Miao; Zhou, Qunfang; Liu, Jiyan; Schnoor, Jerald L; Jiang, Guibin

2017-05-01

Short chain chlorinated paraffins (SCCPs) are ubiquitously present as persistent organic pollutants in the environment. However, little information on the interaction of SCCPs with plants is currently available. In this work, young pumpkin plants (Cucurbita maxima × C. Moschata) were hydroponically exposed to the congener of chlorinated decane, 1,2,5,5,6,9,10-heptachlorodecane (1,2,5,5,6,9,10-HepCD), to investigate the uptake, translocation and transformation of chlorinated decanes in the intact plants. It was found that parent HepCD was taken up by the pumpkin roots, translocated from root to shoots, and phytovolatilized from pumpkin plants to air via the plant transpiration flux. Our data suggested that dechlorination of 1,2,5,5,6,9,10-HepCD to lower chlorinated decanes and rearrangement of chlorine atoms in the molecule were all mediated by the whole pumpkin seedlings. Chlorinated decanes were found in the shoots and roots of blank controls, indicating that chlorinated decanes in the air could be absorbed by leaves and translocated from shoots to roots. Lower chlorinated congeners (C 10 H 17 Cl 5 ) tended to detain in air compared to higher chlorinated congeners (C 10 H 16 Cl 6 and other C 10 H 15 Cl 7 ). Potential transformation pathway and behavior of 1,2,5,5,6,9,10-HepCD in pumpkin were proposed based on these experiments. Copyright © 2017 Elsevier Ltd. All rights reserved.

Semaphorin4D Drives CD8+ T-Cell Lesional Trafficking in Oral Lichen Planus via CXCL9/CXCL10 Upregulations in Oral Keratinocytes.

Science.gov (United States)

Ke, Yao; Dang, Erle; Shen, Shengxian; Zhang, Tongmei; Qiao, Hongjiang; Chang, Yuqian; Liu, Qing; Wang, Gang

2017-11-01

Chemokine-mediated CD8 + T-cell recruitment is an essential but not well-established event for the persistence of oral lichen planus (OLP). Semaphorin 4D (Sema4D)/CD100 is implicated in immune dysfunction, chemokine modulation, and cell migration, which are critical aspects for OLP progression, but its implication in OLP pathogenesis has not been determined. In this study, we sought to explicate the effect of Sema4D on human oral keratinocytes and its capacity to drive CD8 + T-cell lesional trafficking via chemokine modulation. We found that upregulations of sSema4D in OLP tissues and blood were positively correlated with disease severity and activity. In vitro observation revealed that Sema4D induced C-X-C motif chemokine ligand 9/C-X-C motif chemokine ligand 10 production by binding to plexin-B1 via protein kinase B-NF-κB cascade in human oral keratinocytes, which elicited OLP CD8 + T-cell migration. We also confirmed using clinical samples that elevated C-X-C motif chemokine ligand 9/C-X-C motif chemokine ligand 10 levels were positively correlated with sSema4D levels in OLP lesions and serum. Notably, we determined matrix metalloproteinase-9 as a new proteolytic enzyme for the cleavage of sSema4D from the T-cell surface, which may contribute to the high levels of sSema4D in OLP lesions and serum. Our findings conclusively revealed an amplification feedback loop involving T cells, chemokines, and Sema4D-dependent signal that promotes OLP progression. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

9 CFR 592.10 - Authority.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Authority. 592.10 Section 592.10 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE EGG PRODUCTS INSPECTION VOLUNTARY INSPECTION OF EGG PRODUCTS Administration § 592.10 Authority. The Administrator shall...

46 CFR 113.10-9 - Power supply.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Power supply. 113.10-9 Section 113.10-9 Shipping COAST... SYSTEMS AND EQUIPMENT Fire and Smoke Detecting and Alarm Systems § 113.10-9 Power supply. (a) General... battery, the charger must be supplied from the final emergency power source. Upon loss of power to the...

9 CFR 351.10 - Facilities.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Facilities. 351.10 Section 351.10... CERTIFICATION CERTIFICATION OF TECHNICAL ANIMAL FATS FOR EXPORT Facilities and Operations § 351.10 Facilities. (a) Facilities for the preparation, identification, and storage of the technical animal fat to be...

TNF-α blockade induces IL-10 expression in human CD4+ T cells

NARCIS (Netherlands)

Evans, Hayley G.; Roostalu, Urmas; Walter, Gina J.; Gullick, Nicola J.; Frederiksen, Klaus S.; Roberts, Ceri A.; Sumner, Jonathan; Baeten, Dominique L.; Gerwien, Jens G.; Cope, Andrew P.; Geissmann, Frederic; Kirkham, Bruce W.; Taams, Leonie S.

2014-01-01

IL-17+ CD4+ T (Th17) cells contribute to the pathogenesis of several human inflammatory diseases. Here we demonstrate that TNF inhibitor (TNFi) drugs induce the anti-inflammatory cytokine IL-10 in CD4+ T cells including IL-17+ CD4+ T cells. TNFi-mediated induction of IL-10 in IL-17+ CD4+ T cells is

Reduced CD5(+) CD24(hi) CD38(hi) and interleukin-10(+) regulatory B cells in active anti-neutrophil cytoplasmic autoantibody-associated vasculitis permit increased circulating autoantibodies.

Science.gov (United States)

Aybar, L T; McGregor, J G; Hogan, S L; Hu, Y; Mendoza, C E; Brant, E J; Poulton, C J; Henderson, C D; Falk, R J; Bunch, D O

2015-05-01

Pathogenesis of anti-neutrophil cytoplasmic autoantibody (ANCA)-associated vasculitis is B cell-dependent, although how particular B cell subsets modulate immunopathogenesis remains unknown. Although their phenotype remains controversial, regulatory B cells (Bregs ), play a role in immunological tolerance via interleukin (IL)-10. Putative CD19(+) CD24(hi) CD38(hi) and CD19(+) CD24(hi) CD27(+) Bregs were evaluated in addition to their CD5(+) subsets in 69 patients with ANCA-associated vasculitis (AAV). B cell IL-10 was verified by flow cytometry following culture with CD40 ligand and cytosine-phosphate-guanosine (CpG) DNA. Patients with active disease had decreased levels of CD5(+) CD24(hi) CD38(hi) B cells and IL-10(+) B cells compared to patients in remission and healthy controls (HCs). As IL-10(+) and CD5(+) CD24(hi) CD38(hi) B cells normalized in remission within an individual, ANCA titres decreased. The CD5(+) subset of CD24(hi) CD38(hi) B cells decreases in active disease and rebounds during remission similarly to IL-10-producing B cells. Moreover, CD5(+) B cells are enriched in the ability to produce IL-10 compared to CD5(neg) B cells. Together these results suggest that CD5 may identify functional IL-10-producing Bregs . The malfunction of Bregs during active disease due to reduced IL-10 expression may thus permit ANCA production. © 2014 British Society for Immunology.

Passivation Characteristics of Alloy Corrosion-Resistant Steel Cr10Mo1 in Simulating Concrete Pore Solutions: Combination Effects of pH and Chloride.

Science.gov (United States)

Ai, Zhiyong; Sun, Wei; Jiang, Jinyang; Song, Dan; Ma, Han; Zhang, Jianchun; Wang, Danqian

2016-09-01

The electrochemical behaviour for passivation of new alloy corrosion-resistant steel Cr10Mo1 immersed in alkaline solutions with different pH values (13.3, 12.0, 10.5, and 9.0) and chloride contents (0.2 M and 1.0 M), was investigated by various electrochemical techniques: linear polarization resistance, electrochemical impedance spectroscopy and capacitance measurements. The chemical composition and structure of passive films were determined by XPS. The morphological features and surface composition of the immersed steel were evaluated by SEM together with EDS chemical analysis. The results evidence that pH plays an important role in the passivation of the corrosion-resistant steel and the effect is highly dependent upon the chloride contents. In solutions with low chloride (0.2 M), the corrosion-resistant steel has notably enhanced passivity with pH falling from 13.3 to 9.0, but does conversely when in presence of high chloride (1.0 M). The passive film on the corrosion-resistant steel presents a bilayer structure: an outer layer enriched in Fe oxides and hydroxides, and an inner layer, rich in Cr species. The film composition varies with pH values and chloride contents. As the pH drops, more Cr oxides are enriched in the film while Fe oxides gradually decompose. Increasing chloride promotes Cr oxides and Fe oxides to transform into their hydroxides with little protection, and this is more significant at lower pH (10.5 and 9.0). These changes annotate passivation characteristics of the corrosion-resistant steel in the solutions of different electrolyte.

Matrix metalloproteinase-10 (MMP-10) interaction with tissue inhibitors of metalloproteinases TIMP-1 and TIMP-2: binding studies and crystal structure.

Science.gov (United States)

Batra, Jyotica; Robinson, Jessica; Soares, Alexei S; Fields, Alan P; Radisky, Derek C; Radisky, Evette S

2012-05-04

Matrix metalloproteinase 10 (MMP-10, stromelysin-2) is a secreted metalloproteinase with functions in skeletal development, wound healing, and vascular remodeling; its overexpression is also implicated in lung tumorigenesis and tumor progression. To understand the regulation of MMP-10 by tissue inhibitors of metalloproteinases (TIMPs), we have assessed equilibrium inhibition constants (K(i)) of putative physiological inhibitors TIMP-1 and TIMP-2 for the active catalytic domain of human MMP-10 (MMP-10cd) using multiple kinetic approaches. We find that TIMP-1 inhibits the MMP-10cd with a K(i) of 1.1 × 10(-9) M; this interaction is 10-fold weaker than the inhibition of the similar MMP-3 (stromelysin-1) catalytic domain (MMP-3cd) by TIMP-1. TIMP-2 inhibits the MMP-10cd with a K(i) of 5.8 × 10(-9) M, which is again 10-fold weaker than the inhibition of MMP-3cd by this inhibitor (K(i) = 5.5 × 10(-10) M). We solved the x-ray crystal structure of TIMP-1 bound to the MMP-10cd at 1.9 Å resolution; the structure was solved by molecular replacement and refined with an R-factor of 0.215 (R(free) = 0.266). Comparing our structure of MMP-10cd·TIMP-1 with the previously solved structure of MMP-3cd·TIMP-1 (Protein Data Bank entry 1UEA), we see substantial differences at the binding interface that provide insight into the differential binding of stromelysin family members to TIMP-1. This structural information may ultimately assist in the design of more selective TIMP-based inhibitors tailored for specificity toward individual members of the stromelysin family, with potential therapeutic applications.

22 CFR 9.10 - Mandatory declassification review.

Science.gov (United States)

2010-04-01

... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Mandatory declassification review. 9.10 Section 9.10 Foreign Relations DEPARTMENT OF STATE GENERAL SECURITY INFORMATION REGULATIONS § 9.10 Mandatory declassification review. All requests to the Department by a member of the public, a government employee, or an...

CD44 standard and CD44v10 isoform expression on leukemia cells distinctly influences niche embedding of hematopoietic stem cells

OpenAIRE

Erb, Ulrike; Megaptche, Amelie Pajip; Gu, Xiaoyu; Büchler, Markus W; Zöller, Margot

2014-01-01

Background A blockade of CD44 is considered a therapeutic option for the elimination of leukemia initiating cells. However, anti-panCD44 can interfere with hematopoiesis. Therefore we explored, whether a CD44 variant isoform (CD44v)-specific antibody can inhibit leukemia growth without attacking hematopoiesis. As a model we used CD44v10 transfected EL4 thymoma cells (EL4-v10). Methods The therapeutic efficacy of anti-panCD44 and anti-CD44v10 was evaluated after intravenous application of EL4/...

Development of ferritic steels for steam generators of fast breeder reactors

International Nuclear Information System (INIS)

Nguyen-Thanh; Vigneron, G.; Vanderschaeghe, A.

1988-01-01

STEIN INDUSTRIE, a manufacturer of equipment for the conventional and nuclear power industry, has built up expertise in the use of Cr-Mo steels used at high temperatures. The main ferritic steels developed were 10 CD 9-10 (AFNOR), Z10 CDNb V 9-2 (AFNOR), X 20 Cr Mo V 12-1 (DIN) and ASTM Grade 9.1. For the fast breeder reactor system, STEIN INDUSTRIE proposes the use of these steels in the construction of steam generators. The wide programme of development undertaken by STEIN INDUSTRIE is aimed at the following main subjects: - characterization of materials - welding and bending tests - studies of special junctions. This article reports the results obtained

The design of steel string crane with lifting capacity 10 tons

International Nuclear Information System (INIS)

Syamsurrijal Ramdja

2007-01-01

The steel string (sling) used for lift Crane of type of Overhead Travelling Crane, with capacities lifting 10 ton are designed. If compared to other string type, string of steel have some excellence. At this design, election of type of string become primary and the factor of safety become prima facie matter with pursuant to up to date standard. From made of design, is hence got by specification and age of steel string. (author)

Crohn's disease intestinal CD4+ T cells have impaired interleukin-10 productionwhich is not restored by probiotic bacteria

DEFF Research Database (Denmark)

Hvas, Christian L; Kelsen, Jens; Agnholt, Jørgen

2007-01-01

OBJECTIVE: Crohn's disease (CD) has been associated with low mucosal interleukin (IL)-10 production, but the mechanism behind this deficiency remains unclear. The aim of this study was to investigate IL-10 and interferon (IFN)-gamma production in intestinal CD4+ T cells from CD patients and healthy...... volunteers (HV) and to examine how this was affected by bacterial products and the presence or absence of autologous dendritic cells. MATERIAL AND METHODS: We cultured intestinal CD4+ T cells from CD patients (n=9) and HV (n=6) and differentiated dendritic cells from their peripheral monocytes. Intestinal T...... this imbalance in CD, but tended to do so in HV. When there were no dendritic cells, CD intestinal T cells responded to autologous bacteria with an increased IFN-gamma production (2.3+/-1.3 ng/ml) compared with HV intestinal T cells (0.3+/-0.2 ng/ml). CONCLUSIONS: Crohn's disease intestinal CD4+ T cells display...

9 CFR 590.10 - Authority.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Authority. 590.10 Section 590.10 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE EGG PRODUCTS... Authority. The Administrator shall perform, for and under the supervision of the Secretary, such duties as...

NLRP10 Enhances CD4+ T-Cell-Mediated IFNγ Response via Regulation of Dendritic Cell-Derived IL-12 Release

Directory of Open Access Journals (Sweden)

Maurizio Vacca

2017-11-01

Full Text Available NLRP10 is a nucleotide-binding oligomerization domain-like receptor that functions as an intracellular pattern recognition receptor for microbial products. Here, we generated a Nlrp10−/− mouse to delineate the role of NLRP10 in the host immune response and found that Nlrp10−/− dendritic cells (DCs elicited sub-optimal IFNγ production by antigen-specific CD4+ T cells compared to wild-type (WT DCs. In response to T-cell encounter, CD40 ligation or Toll-like receptor 9 stimulation, Nlrp10−/− DCs produced low levels of IL-12, due to a substantial decrease in NF-κB activation. Defective IL-12 production was also evident in vivo and affected IFNγ production by CD4+ T cells. Upon Mycobacterium tuberculosis (Mtb infection, Nlrp10−/− mice displayed diminished T helper 1-cell responses and increased bacterial growth compared to WT mice. These data indicate that NLRP10-mediated IL-12 production by DCs is critical for IFNγ induction in T cells and contributes to promote the host defense against Mtb.

Results obtained so far with the production of turbine and valve casings made of the new 9% Cr cast steel types G-X 12 CrMoWVNbN 10 11 and G-X 12 CrMoVNbN 91; Erfahrungsbericht ueber die Herstellung von Turbinen- und Ventilgehaeusen aus den neuen 9% Cr-Stahlgusssorten G-X 12 CrMoWVNbN 10 1 1 und G-X 12 CrMoVNbN 91

Energy Technology Data Exchange (ETDEWEB)

Schuster, F.; Buberl, A.; Hanus, R. [VOEST-ALPINE STAHL LINZ GmbH, Linz (Austria); Cerjak, H. [Technische Univ., Graz (Austria)

1996-12-31

In the course of production start-up of new 9-10% Cr cast steel types, and application of R and D results to practice, the following examinations and modifications have been performed: 1. Reduction of average chromium content from 10.5 to 9.5% in order to suppress delta ferrite segregation, and adjustment of austenite and ferrite stabilizing alloying constituents. 2. Analysis of typical defects in castings, and modification of casting and feeding techniques in compliance with the saturation behaviour of the new 9-10% Cr steels. These measures achieved a reduction of feeding-based flaws (shrinkage) in the last few cast pieces. 3. The good weldability was proven of the new 9-10% Cr steels by means of welding tests and crack-free production and construction welds made in cast pieces. (orig./MM) [Deutsch] Im Zuge der Produktionsaufnahme neuer 9-10% Cr-Stahlgusssorten und der Ueberleitung der F and E Ergebnisse in die betriebliche Praxis wurden folgende Untersuchungen und Anpassungen vorgenommen: 1. Um die Deltaferritausscheidung zu unterdruecken, wurde der mittlere Chromgehalt von 10,5 auf 9,5% abgesenkt und die austenit- und ferritstabilisierenden Legierungselemente besser angepasst. 2. Die Analyse typischer Fehlererscheinungen an Gussstuecken machten eine Anpassung der Giess- und Speisungstechnik an das Saettigungsverhalten der neuen 9-10% Cr-Staehle erforderlich. Diese Massnahmen fuehrten zu einer Verringerung der Speisungsfehler (Lunker) bei den zuletzt abgegossenen Gussstuecken. 3. Bei Schweissversuchen und an Gussstuecken rissfrei ausgefuehrten Fertigungs- und Konstruktionsschweissungen konnte die gute Schweisseignung der neuen 9-10% Cr-Staehle nachgewiesen werden. (orig./MM)

Mechanical properties of irradiated 9Cr-2WVTa steel

International Nuclear Information System (INIS)

Klueh, R.L.; Alexander, D.J.; Rieth, M.

1998-01-01

An Fe-9Cr-2W-0.25V-0.07Ta-0.1C (9Cr-2WVTa) steel has excellent strength and impact toughness before and after irradiation in the Fast Flux Test Facility and the High Flux Reactor (HFR). The ductile-brittle transition temperature (DBTT) increased only 32 C after 28 dpa at 365 C in FFTF, compared to a shift of ∼60 C for a 9Cr-2WV steel--the same as the 9Cr-2WVTa steel but without tantalum. This difference occurred despite the two steels having similar tensile but without tantalum. This difference occurred despite the two steels having similar tensile properties before and after irradiation. The 9Cr-2WVTa steel has a smaller prior-austenite grain size, but otherwise microstructures are similar before irradiation and show similar changes during irradiation. The irradiation behavior of the 9Cr-2WVTa steel differs from the 9Cr-2WV steel and other similar steels in two ways: (1) the shift in DBTT of the 9Cr-2WVTa steel irradiated in FFTF does not saturate with fluence by ∼28 dpa, whereas for the 9Cr-2WV steel and most similar steels, saturation occurs at <10 dpa, and (2) the shift in DBTT for 9Cr-2WVTa steel irradiated in FFTF and HFR increased with irradiation temperature, whereas it decreased for the 9Cr-2WV steel, as it does for most similar steels. The improved properties of the 9Cr-2WVTa steel and the differences with other steels were attributed to tantalum in solution

Diagnostic value of CD-10 marker in differentiating of papillary thyroid carcinoma from benign thyroid lesions

Directory of Open Access Journals (Sweden)

Mojgan Mokhtari

2014-01-01

Full Text Available Background: Using of CD10 in accordance with clinical and histological features of thyroid lesions could be used as both diagnostic and prognostic tool, which consequently influence the management and their prognosis for survival of patients with thyroid neoplasms especially papillary thyroid carcinoma (PTC. The aim of this study was to determine its expression in PTC and different benign thyroid lesions. Materials and Methods: In this descriptive-analytic, cross-sectional study, paraffin-embedded tissues of patients with definitive pathologic diagnosis of different benign thyroid lesions and PTC were retrieved. Immunostained sections of each slides was performed using immunohistochemistry methods and expression of CD10 was compared in two groups of benign thyroid lesions and PTC. Results: From selected cases 134 sections studied in two groups of PTC (n = 67 and benign thyroid lesions (n = 67. CD10 were immunohistochemically positive in 29.9% of PTC cases, but in none of the thyroid benign lesions (0% (P 0.05. Conclusion: The results of the current study indicate that due to the higher expression of CD10 in PTC than benign thyroid lesions it might be used for differentiating mentioned lesions. But for using it as a diagnostic tool further studies with larger sample size and determination of its sensitivity, specificity and cut-off point is necessary.

The role of CD40L, IL-10 and IL-17 in radioprotection

International Nuclear Information System (INIS)

Li Ting

2003-01-01

CD40L/CD40 interaction is central to the control of thymus-dependent humoral immunity and cell mediated immune responses. IL-17 has been shown to induce the production of IL-6 and G-CSF, which can induce proliferation and differentiation of CD34 + hematopoietic progenitors. IL-10 can interfere with up-regulation of costimulatory molecules, thus suppressing the production of costimulatory cytokines, such as IL-12. IL-10 has been implicated as an essential mediator in the induction of systemic immune suppression following ultraviolet (UV) exposure. Treating UV-irradiated mice with anti-IL-10 blocks the induction of immune suppression

Effect of partial oxygen pressure on physicochemical properties of Kh18N10T steel at isothermal oxidation. Vliyanie partsial'nogo davleniya kisloroda na fiziko-khimicheskie svojstva poverkhnosti stali Kh18N10T pri izotermicheskom okislenii

Energy Technology Data Exchange (ETDEWEB)

Alekseev, V N; Oshe, E K; Fokin, M N; Bogdanova, S V; Loskutov, A I [AN SSSR, Moscow (USSR). Inst. Fizicheskoj Khimii

1990-10-01

Auger-electron spectroscopy, photoelectric polarization, conductometry methods have been used to analyze chemical and defect composition of surface oxide layers, formed on stainless steel Kh18N10T in vacuum (10{sup -9} - 10{sup -2} torr) and at temperatures 593-673 K. The boundary conditions of manifestation of extermal behaviour of the dependence of the surface oxide growth rate at isothermal oxidation of this steel are determined. The relation between passivation properties of the surface oxide and the magnitude of the edge angle of the surface wetting with molten tin is revealed.

Effect of welding thermal cycles on the structure and properties of simulated heat-affected zone areas in X10CrMoVNb9-1 (T91) steel at a state after 100,000 h of operation

Energy Technology Data Exchange (ETDEWEB)

Łomozik, Mirosław, E-mail: miroslaw.lomozik@is.gliwice.pl [Instytut Spawalnictwa, Testing of Materials Weldability and Welded Constructions Department, 44-100 Gliwice, Bł. Czesława 16-18 (Poland); Hernas, Adam, E-mail: adam.hernas@polsl.pl [Silesian University of Technology, Faculty of Materials Engineering and Metallurgy, 40-019 Katowice, Krasińskiego 8 str. (Poland); Zeman, Marian L., E-mail: marian.zeman@is.gliwice.pl [Instytut Spawalnictwa, Testing of Materials Weldability and Welded Constructions Department, 44-100 Gliwice, Bł. Czesława 16-18 (Poland)

2015-06-18

The article presents results of structural tests (light, scanning electron and scanning transmission electron microscopy) of X10CrMoVNb9-1 (T91) creep-resisting steel after approximately 100,000 h of operation. It was ascertained that the parent metal of T91 steel is characterized by the microstructure of tempered martensite with M{sub 23}C{sub 6} carbide precipitates and few dispersive precipitates of MX-type niobium and vanadium carbonitrides. The most inconvenient change in T91 steel precipitate morphology due to long-term operation is the appearance of the Laves Fe{sub 2}Mo phase which along with M{sub 23}C{sub 6} carbide particles forms elongated blocks and conglomerates on grain boundaries. The article also presents results of tests related to the effect of simulated welding thermal cycles on selected properties of X10CrMoVNb9-1 (T91) grade steel at a state after approximately 100,000 h of operation. The tests involved the determination of the chemical composition of the steel tested as well as impact tests, hardness measurements and microscopic metallographic examination (based on light microscopy) of simulated heat-affected zone (HAZ) areas for a cooling time (t{sub 8/5}) restricted within a range between 3 s and 120 s, with and without heat treatment. The tests revealed that, among other results, hardness values of simulated HAZ areas in X10CrMoVNb9-1 (T91) steel do not guarantee cold crack safety of the steel at the state without additional heat treatment. It was also observed that simulated welding thermal cycles of cooling times t{sub 8/5}=3, 12, 60 and 120 s do not significantly affect the toughness and hardness of simulated HAZ areas of the steel tested.

9 CFR 441.10 - Retained water.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Retained water. 441.10 Section 441.10... STANDARDS: RAW PRODUCTS § 441.10 Retained water. (a) Raw livestock and poultry carcasses and parts will not be permitted to retain water resulting from post-evisceration processing unless the establishment...

One-electron reduction of 9,10-anthraquinone, 1-amino-9,10-anthraquinone and 1-hydroxy-9,10-anthraquinone in aqueous-isopropanol-acetone mixed solvent: a pulse radiolysis study

International Nuclear Information System (INIS)

Pal, H.; Mukherjee, T.; Mittal, J.P.

1994-01-01

The semiquinone radicals produced by one-electron reduction of 9,10-anthraquinone, 1-amino- 9,10-anthraquinone and 1-hydroxy-9,10-anthraquinone have been characterized in aqueous-organic mixed solvent comprising of 30.2 mol dm -3 water, 5 mol dm -3 isopropanol and 1 mol dm -3 acetone, using the pulse radiolysis technique. Spectroscopic characteristics, the kinetic parameters of formation and decay and one acid dissociation constants of the semiquinones and one-electron reduction potentials of the quinones have been estimated. The characteristics of the present semiquinone systems have been compared with those of other similar systems. The observed differences in characteristics of the semiquinones due to different substitutions have been analysed. (Author)

10 CFR 16.9 - Hearing.

Science.gov (United States)

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Hearing. 16.9 Section 16.9 Energy NUCLEAR REGULATORY... § 16.9 Hearing. (a) Request for hearing. (1) An employee shall file a petition for a hearing in... creditor agency, a hearing may be requested by filing a written petition stating why the employee disputes...

10 CFR 9.85 - Fees.

Science.gov (United States)

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Fees. 9.85 Section 9.85 Energy NUCLEAR REGULATORY COMMISSION PUBLIC RECORDS Privacy Act Regulations Fees § 9.85 Fees. Fees shall not be charged for search or... available for review, although fees may be charged for additional copies. Fees established under 31 U.S.C...

Structural changes in surface layer of steel 08Kh18N10T during machining

International Nuclear Information System (INIS)

Palenik, J.; Vodarek, V.

1989-01-01

The results are reported of a study of the surface layer of steel 08Kh18N10T affected by machining. Structural changes were studied caused by finish turning and by additional roller burnishing. Multiple deformation bands were observed to occur under the given cutting conditions; they mainly consisted of deformation doublets and only in isolated cases of ε-martensite. The presence of α'-martensite was not shown in the specimen surface layer following finish turning. The deformation shear bands in the roller-burnished specimen consisted of both ε-martensite and of deformation doublets. The amount of ε-martensite in the structure was significantly higher than in the specimen worked by turning. Local presence of α'-martensite formations was observed inside the deformation bands. It thus follows that roller burnishing is unsuitable as part of the manufacture of components from steel 08Kh18N10T. (J.B.). 5 figs., 1 tab., 9 refs

Asymptotic normalization coefficients for 10B→9Be+p

International Nuclear Information System (INIS)

Mukhamedzhanov, A.M.; Clark, H.L.; Gagliardi, C.A.; Lui, Y.; Trache, L.; Tribble, R.E.; Xu, H.M.; Zhou, X.G.; Burjan, V.; Cejpek, J.; Kroha, V.; Carstoiu, F.

1997-01-01

The differential cross sections for the reactions 9 Be( 10 B, 10 B) 9 Be and 9 Be( 10 B, 9 Be) 10 B have been measured at an incident energy of 100 MeV. The elastic scattering data have been used to determine the optical model parameters for the 9 Be+ 10 B system at this energy. These parameters are then used in distorted-wave Born approximation (DWBA) calculations to predict the cross sections of the 9 Be( 10 B, 9 Be) 10 B proton exchange reaction, populating the ground and low-lying states in 10 B. By normalizing the theoretical DWBA proton exchange cross sections to the experimental ones, the asymptotic normalization coefficients (ANC's), defining the normalization of the tail of the 10 B bound state wave functions in the two-particle channel 9 Be+p, have been found. The ANC for the virtual decay 10 B(g.s.)→ 9 Be+p will be used in an analysis of the 10 B( 7 Be, 8 B) 9 Be reaction to extract the ANC's for 8 B→ 7 Be +p. These ANC's determine the normalization of the 7 Be(p,γ) 8 B radiative capture cross section at very low energies, which is crucially important for nuclear astrophysics. copyright 1997 The American Physical Society

Synthesis and Electroluminescence Properties of 3-(Trifluoromethylphenyl-Substituted 9,10-Diarylanthracene Derivatives for Blue Organic Light-Emitting Diodes

Directory of Open Access Journals (Sweden)

Sang Woo Kwak

2017-10-01

Full Text Available Diaryl-substituted anthracene derivatives containing 3-(trifluoromethylphenyl groups, 9,10-diphenyl-2-(3-(trifluoromethylphenylanthracene (1, 9,10-di([1,1′-biphenyl]-4-yl-2-(3-(trifluoromethylphenylanthracene (2, and 9,10-di(naphthalen-2-yl-2-(3-(trifluoromethylphenylanthracene (3 were synthesized and characterized. The compounds 1–3 possessed high thermal stability and proper frontier-energy levels, which make them suitable as host materials for blue organic light-emitting diodes. The electroluminescent (EL emission maximum of the three N,N-diphenylamino phenyl vinyl biphenyl (DPAVBi-doped (8 wt % devices for compounds 1–3 was exhibited at 488 nm (for 1 and 512 nm (for 2 and 3. Among them, the 1-based device displayed the highest device performances in terms of brightness (Lmax = 2153.5 cd·m−2, current efficiency (2.1 cd·A−1, and external quantum efficiency (0.8%, compared to the 2- and 3-based devices.

Synthesis, purification, and time-dependent disposition studies of 9- or 10-mono-iodostearic acid and 9- and 10-mono-iodostearyl carnitine

International Nuclear Information System (INIS)

Reed, K.W.

1985-01-01

The purpose of this investigation was to evaluate the potential use of radiolabeled 9- or 10-mono-iodostearyl carnitine as a perfusion and metabolic imaging agent for the heart. Radiochemical purity was achieved and determined by the use of silica gel and/or anion exchange resin chromatography. Radiochemical yields of 45-63 and 4% were obtained for the fatty acid and carnitine ester, respectively. Male albino mice were sacrificed at 2, 5, 7, 10, 15, 20, 30, and 50 minutes post-injection with either 125 I 9- or 10-mono-iodostearic acid or 9- or 10-mono-iodostearyl (-) carnitine. The lungs, liver heart, kidney, spleen, pancreas, small intestine, stomach, thyroid, blood, fat, and skeletal muscle tissue were excised and assayed for levels of radioactivity in a NaI crystal well counter. The very low target-to-nontarget ratios obtained with 125 I 9- or 10-mono-iodostearyl carnitine in mice strongly suggest that radioiodinated 9- or 10-mono-iodostearyl carnitine is not suitable for use as a myocardial imaging agent. However, radioiodinated 9- or 10-mono-iodostearic acid showed promise as a myocardial imaging agent and may warrant further investigation

Composition and corrosion properties of high-temperature oxide films on steel type 18-10

International Nuclear Information System (INIS)

Vakulenko, B.F.; Morozov, O.N.; Chernysheva, M.V.

1985-01-01

The composition and propeties of oxide films, formed in the process of tube production of steel type 18-10, as well as the behaviour of the steels coated with oxide films under operating conditions of NPP heat-exchange equipment at the 20-300 deg C temperatures are determined. It is found, that the films have a good adhesion to the steel surface and repeat the metal structure without interfering with, the surface defect determination. Introduction of the NaNO 2 corrosion inhibitor decreases the film destruction rate to the level of the base metal corrosion. It is found acceptable to use tubes of steel 18-10 coated with dense oxide films in the heat-exchange and water supply systems of NPP

Reliability and validity of the Spanish version of the 10-item Connor-Davidson Resilience Scale (10-item CD-RISC in young adults

Directory of Open Access Journals (Sweden)

García-Campayo Javier

2011-08-01

Full Text Available Abstract Background The 10-item Connor-Davidson Resilience Scale (10-item CD-RISC is an instrument for measuring resilience that has shown good psychometric properties in its original version in English. The aim of this study was to evaluate the validity and reliability of the Spanish version of the 10-item CD-RISC in young adults and to verify whether it is structured in a single dimension as in the original English version. Findings Cross-sectional observational study including 681 university students ranging in age from 18 to 30 years. The number of latent factors in the 10 items of the scale was analyzed by exploratory factor analysis. Confirmatory factor analysis was used to verify whether a single factor underlies the 10 items of the scale as in the original version in English. The convergent validity was analyzed by testing whether the mean of the scores of the mental component of SF-12 (MCS and the quality of sleep as measured with the Pittsburgh Sleep Index (PSQI were higher in subjects with better levels of resilience. The internal consistency of the 10-item CD-RISC was estimated using the Cronbach α test and test-retest reliability was estimated with the intraclass correlation coefficient. The Cronbach α coefficient was 0.85 and the test-retest intraclass correlation coefficient was 0.71. The mean MCS score and the level of quality of sleep in both men and women were significantly worse in subjects with lower resilience scores. Conclusions The Spanish version of the 10-item CD-RISC showed good psychometric properties in young adults and thus can be used as a reliable and valid instrument for measuring resilience. Our study confirmed that a single factor underlies the resilience construct, as was the case of the original scale in English.

9 CFR 4.10 - Summary action.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Summary action. 4.10 Section 4.10 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE ANIMAL WELFARE RULES OF PRACTICE GOVERNING PROCEEDINGS UNDER THE ANIMAL WELFARE ACT Supplemental Rules of...

19 CFR 10.9 - Articles exported for processing.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Articles exported for processing. 10.9 Section 10... THE TREASURY ARTICLES CONDITIONALLY FREE, SUBJECT TO A REDUCED RATE, ETC. General Provisions Articles Exported and Returned § 10.9 Articles exported for processing. (a) Except as otherwise provided for in this...

10 CFR 1023.9 - General guidelines.

Science.gov (United States)

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false General guidelines. 1023.9 Section 1023.9 Energy DEPARTMENT OF ENERGY (GENERAL PROVISIONS) CONTRACT APPEALS Overview: Organization, Functions and Authorities § 1023.9 General guidelines. (a) The principles of this Overview shall apply to all Board functions...

Plasma CXCL10, sCD163 and sCD14 Levels Have Distinct Associations with Antiretroviral Treatment and Cardiovascular Disease Risk Factors.

Directory of Open Access Journals (Sweden)

Alison Castley

Full Text Available We investigate the associations of three established plasma biomarkers in the context of HIV and treatment-related variables including a comprehensive cardiovascular disease risk assessment, within a large ambulatory HIV cohort. Patients were recruited in 2010 to form the Royal Perth Hospital HIV/CVD risk cohort. Plasma sCD14, sCD163 and CXCL10 levels were measured in 475 consecutive patients with documented CVD risk (age, ethnicity, gender, smoking, blood pressure, BMI, fasting metabolic profile and HIV treatment history including immunological/virological outcomes. The biomarkers assessed showed distinct associations with virological response: CXCL10 strongly correlated with HIV-1 RNA (p0.2. Associations between higher sCD163 and protease inhibitor therapy (p = 0.05 and lower sCD14 with integrase inhibitor therapy (p = 0.02 were observed. Levels of sCD163 were also associated with CVD risk factors (age, ethnicity, HDL, BMI, with a favourable influence of Framingham score <10% (p = 0.04. Soluble CD14 levels were higher among smokers (p = 0.002, with no effect of other CVD risk factors, except age (p = 0.045. Our findings confirm CXCL10, sCD163 and sCD14 have distinct associations with different aspects of HIV infection and treatment. Levels of CXCL10 correlated with routinely monitored variables, sCD163 levels reflect a deeper level of virological suppression and influence of CVD risk factors, while sCD14 levels were not associated with routinely monitored variables, with evidence of specific effects of smoking and integrase inhibitor therapy warranting further investigation.

Plasma CXCL10, sCD163 and sCD14 Levels Have Distinct Associations with Antiretroviral Treatment and Cardiovascular Disease Risk Factors

Science.gov (United States)

Castley, Alison; Williams, Leah; James, Ian; Guelfi, George; Berry, Cassandra; Nolan, David

2016-01-01

We investigate the associations of three established plasma biomarkers in the context of HIV and treatment-related variables including a comprehensive cardiovascular disease risk assessment, within a large ambulatory HIV cohort. Patients were recruited in 2010 to form the Royal Perth Hospital HIV/CVD risk cohort. Plasma sCD14, sCD163 and CXCL10 levels were measured in 475 consecutive patients with documented CVD risk (age, ethnicity, gender, smoking, blood pressure, BMI, fasting metabolic profile) and HIV treatment history including immunological/virological outcomes. The biomarkers assessed showed distinct associations with virological response: CXCL10 strongly correlated with HIV-1 RNA (p0.2). Associations between higher sCD163 and protease inhibitor therapy (p = 0.05) and lower sCD14 with integrase inhibitor therapy (p = 0.02) were observed. Levels of sCD163 were also associated with CVD risk factors (age, ethnicity, HDL, BMI), with a favourable influence of Framingham score <10% (p = 0.04). Soluble CD14 levels were higher among smokers (p = 0.002), with no effect of other CVD risk factors, except age (p = 0.045). Our findings confirm CXCL10, sCD163 and sCD14 have distinct associations with different aspects of HIV infection and treatment. Levels of CXCL10 correlated with routinely monitored variables, sCD163 levels reflect a deeper level of virological suppression and influence of CVD risk factors, while sCD14 levels were not associated with routinely monitored variables, with evidence of specific effects of smoking and integrase inhibitor therapy warranting further investigation. PMID:27355513

White organic light-emitting diodes with 9, 10-bis (2-naphthyl) anthracene

International Nuclear Information System (INIS)

Guan Yunxia; Niu Lianbin

2009-01-01

White organic light-emitting diodes were fabricated by 9, 10-bis (2-naphthyl) anthracene (ADN) doped with Rubrene with a structure of ITO/copper phthalocyanine (CuPc) / NPB /ADN: Rubrene /Alq 3 /CsF/Mg:Ag/Ag. Multilayer organic devices using AND and Rubrene as an emitting layer produced white emissions with good chromaticity and luminous efficiency as high as 5.93 cd/A. This performance can be explained by Foerster energy transfer from the blue-emitting host to the orange-emitting dopant.

10 CFR 61.9 - Employee protection.

Science.gov (United States)

2010-01-01

... occurs because the employee has engaged in protected activities. An employee's engagement in protected... 10 Energy 2 2010-01-01 2010-01-01 false Employee protection. 61.9 Section 61.9 Energy NUCLEAR... Provisions § 61.9 Employee protection. (a) Discrimination by a Commission licensee, an applicant for a...

10 CFR 71.9 - Employee protection.

Science.gov (United States)

2010-01-01

.... An employee's engagement in protected activities does not automatically render him or her immune from... 10 Energy 2 2010-01-01 2010-01-01 false Employee protection. 71.9 Section 71.9 Energy NUCLEAR... § 71.9 Employee protection. (a) Discrimination by a Commission licensee, certificate holder, an...

10 CFR 60.9 - Employee protection.

Science.gov (United States)

2010-01-01

... occurs because the employee has engaged in protected activities. An employee's engagement in protected... 10 Energy 2 2010-01-01 2010-01-01 false Employee protection. 60.9 Section 60.9 Energy NUCLEAR... Provisions § 60.9 Employee protection. (a) Discrimination by a Commission licensee, an applicant for a...

10 CFR 63.9 - Employee protection.

Science.gov (United States)

2010-01-01

... because the employee has engaged in protected activities. An employee's engagement in protected activities... 10 Energy 2 2010-01-01 2010-01-01 false Employee protection. 63.9 Section 63.9 Energy NUCLEAR... MOUNTAIN, NEVADA General Provisions § 63.9 Employee protection. (a) Discrimination by a Commission licensee...

Representation of the properties 10 CrMoNiNb 9 10

International Nuclear Information System (INIS)

Dette, M.; Hahn, H.; Nieuwland, H.C.D.; Tichler, J.W.

The high-temperature ferritic steal 10 CrMoNiNb 9 10 is used as structural material in nuclear steam generators. It is exposed to loads within the creep range. In order to resist safety also loads caused by incidents after long temperature stress, the time-independent stability parameters must not fall below specified minimum values. The material is characterised by the stability degree Nb/C+N and the niobium excess δ Nb. (orig.) [de

The research of axial corrosion fatigue on 10Ni3CrMoV steel

Science.gov (United States)

Xie, Xing; Yi, Hong; Xu, Jian; Xie, Kun

2017-09-01

Fatigue life had been studied with 10CrNi3MoV steel at different load ratios and in different environmental medias. The microstructure and micro-topography had been observed and analyzed by means of SEM, EDS and TEM. Our findings indicated that, the fatigue life of 10Ni3CrMoV steel in seawater was shorter than in air, the difference in longevity was larger with the decreasing of axis stress. Corrosion pits had a great influence on corrosion fatigue life.

Effects of peritoneal fluid from endometriosis patients on interferon-gamma-induced protein-10 (CXCL10) and interleukin-8 (CXCL8) released by neutrophils and CD4+ T cells.

Science.gov (United States)

Kim, Ji-Yeon; Lee, Dong-Hyung; Joo, Jong-Kil; Jin, Jun-O; Wang, Ji-Won; Hong, Young-Seoub; Kwak, Jong-Young; Lee, Kyu-Sup

2009-09-01

Intraperitoneal immuno-inflammatory changes may be associated with the pathogenesis of endometriosis. We evaluated the effects of peritoneal fluid obtained from patients with endometriosis (ePF) on the release of interferon-gamma-induced protein-10 (IP-10/CXCL10) and interleukin-8 (IL-8/CXCL8) by neutrophils, CD4(+) T cells, and monocytes. Neutrophils, CD4(+) T cells, and monocytes were cultured with ePF and the chemokine levels in the supernatants were then measured using enzyme-linked immunosorbent assay. The addition of ePF to cultures of CD4(+) T cells led to a significant increase in the release of IP-10 when compared with control PF without endometriosis (cPF). There was a positive correlation between the levels of IL-8 and IP-10 in ePF (R = 0.89, P = 0.041), but not between the levels of IP-10 and IL-8 released by neutrophils, CD4(+) T cells, and monocytes. The levels of IP-10 in ePF were positively correlated with the release of IP-10 by ePF-treated neutrophils (R = 0.89, P ePF significantly enhanced the interferon-gamma-induced release of IP-10 by nuetrophils and CD4(+) T cells. These findings suggest that neutrophils and T cells release differential levels of IP-10 and IL-8 in response to stimulation with ePF, and that these cells are a major source of IP-10 in the PF of endometriosis patients.

Enhancement of strength properties of hot rolled 10KHSND steel

International Nuclear Information System (INIS)

Nasibov, A.G.; Popova, L.V.; Pikulin, S.A.; Globa, N.I.

1989-01-01

To find out the reasons of low hot rolling yield for 10KhSND steel sheets in mechanical properties, titanium effect in the range of 0.008-0.03% concentrations is studied. It is established that the titanium content in a solid solution is conserved within 0.003-0.005%, the rest of titanium is bound to carbonitrides Ti(C, N). It is shown that alloys with 0.025-0.03% titanium content possess the increased values of ultimate and yield strength the necessary level of impact strength and good wealdability. The good steel yield, when the titanium content is sustained at the given level, increases from 40 to 85%

Strength of 10CR-N martensitic steels

International Nuclear Information System (INIS)

Bahrami, F.; Hendry, A.

1993-01-01

10Cr stainless steel has been employed to examine the effect of nitrogen on microstructure and strength. Applying Solid state gaseous nitrogenising treatments a whole range of nitrogen martensite structures containing up to 0.45 wt% were obtained. It was found that a linear relationship exists between strength and nitrogen content in precipitate free martensitic structures. Yield strength increased from 705 to 1295 MPa for nitrogen free base material and alloys with 0.35 wt%N respectively. Pronounce secondary hardening was observed at a tempering temperature of 500 C. A linear relationship was also observed between the lattice parameter and nitrogen concentration in these alloys. A model for mechanical behaviour is presented. (orig.)

Improved efficiency in organic light-emitting devices with tris-(8-hydroxyquinoline) aluminium doped 9,10-di(2-naphthyl) anthracene emission layer

Energy Technology Data Exchange (ETDEWEB)

Yuan Yongbo; Lian Jiarong; Li Shuang; Zhou Xiang [State Key Lab of Optoelectronic Materials and Technologies, Sun Yat-Sen University, Guangzhou, 510275 (China)], E-mail: stszx@mail.sysu.edu.cn

2008-11-21

Organic light-emitting devices with tris-(8-hydroxyquinoline) aluminium (Alq{sub 3}) doped 9,10-di(2-naphthyl) anthracene (ADN) as the emission layer (EML) have been fabricated. These devices exhibit efficient electroluminescence (EL) originated from the Alq{sub 3} as the mass ratio of Alq{sub 3} to ADN was varied from 1 to 50%. The devices with an optimal Alq{sub 3} mass ratio of 10 wt% showed a peak EL efficiency and an external quantum efficiency of 9.1 cd A{sup -1} and 2.7% at a luminance of 1371 cd m{sup -2}, which is improved by a factor of 2.2 compared with 4.1 cd A{sup -1} and 1.2% at a luminance of 3267 cd m{sup -2} for conventional devices with the neat Alq{sub 3} as the EML.

White organic light-emitting diodes with 9, 10-bis (2-naphthyl) anthracene

Energy Technology Data Exchange (ETDEWEB)

Guan Yunxia; Niu Lianbin [Key Laboratory of Optical Engineering, College of Physics and Information Technology, Chongqing Normal University, Chongqing 400047 (China)], E-mail: gyxybsy@126.com, E-mail: niulb03@126.com

2009-03-01

White organic light-emitting diodes were fabricated by 9, 10-bis (2-naphthyl) anthracene (ADN) doped with Rubrene with a structure of ITO/copper phthalocyanine (CuPc) / NPB /ADN: Rubrene /Alq{sub 3} /CsF/Mg:Ag/Ag. Multilayer organic devices using AND and Rubrene as an emitting layer produced white emissions with good chromaticity and luminous efficiency as high as 5.93 cd/A. This performance can be explained by Foerster energy transfer from the blue-emitting host to the orange-emitting dopant.

Poly[tetraaqua(μ6-9,10-dioxo-9,10-dihydroanthracene-1,4,5,8-tetracarboxylatodimanganese(II

Directory of Open Access Journals (Sweden)

Rui Xu

2012-07-01

Full Text Available The title complex, [Mn2(C18H4O10(H2O4]n, was synthesized from manganese(II chloride tetrahydrate and 9,10-dioxo-9,10-dihydroanthracene-1,4,5,8-tetracarboxylic acid (H4AQTC in water. The anthraquinone unit is located about a crystallographic center of inversion. Each asymmetric unit therefore contains one MnII atom, two water ligands and one half AQTC4− anion. The MnII atom is coordinated in a distorted octahedral geometry by four O atoms from three AQTC4− ligands and two water O atoms. Two of the carboxylate groups coordinate one MnII atom in a chelating mode, whereas the others each coordinate two MnII atoms. Each AQTC4− tetra-anion therefore coordinates six different MnII ions and, as a result, a three-dimensional coordination polymer is formed. O—H...O hydrogen bonds, some of them bifurcated, between water ligands and neighboring water or anthraquinone ligands are observed in the crystal structure.

Interleukin-10 (IL-10) pathway: genetic variants and outcomes of HIV-1 infection in African American adolescents.

Science.gov (United States)

Shrestha, Sadeep; Wiener, Howard W; Aissani, Brahim; Song, Wei; Shendre, Aditi; Wilson, Craig M; Kaslow, Richard A; Tang, Jianming

2010-10-14

Immunological and clinical outcomes can vary considerably at the individual and population levels during both treated and untreated HIV-1 infection. Cytokines encoded by the interleukin-10 gene (IL10) family have broad immunomodulatory function in viral persistence, and several SNPs in the IL10 promoter sequence have been reported to influence pathogenesis or acquisition of HIV-1 infection. We examined 104 informative SNPs in IL10, IL19, IL20, IL24, IL10RA and IL10RB among 250 HIV-1 seropositive and 106 high-risk seronegative African American adolescents in the REACH cohort. In subsequent evaluation of five different immunological and virological outcomes related to HIV-1 infection, 25 SNPs were associated with a single outcome and three were associated with two different outcomes. One SNP, rs2243191 in the IL19 open reading frame (Ser to Phe substitution) was associated with CD4(+) T-cell increase during treatment. Another SNP rs2244305 in IL10RB (in strong linkage disequilibrium with rs443498) was associated with an initial decrease in CD4(+) T-cell by 23 ± 9% and 29 ± 9% every 3 months (for AA and AG genotypes, respectively, compared with GG) during ART-free period. These associations were reversed during treatment, as CD4(+) T-cell increased by 31 ± 0.9% and 17 ± 8% every 3 months for AA and AG genotype, respectively. In African Americans, variants in IL10 and related genes might influence multiple outcomes of HIV-1 infection, especially immunological response to HAART. Fine mapping coupled with analysis of gene expression and function should help reveal the immunological importance of the IL10 gene family to HIV-1/AIDS.

Per a 10 protease activity modulates CD40 expression on dendritic cell surface by nuclear factor-kappaB pathway.

Science.gov (United States)

Goel, C; Kalra, N; Dwarakanath, B S; Gaur, S N; Arora, N

2015-05-01

Serine protease activity of Per a 10 from Periplaneta americana modulates dendritic cell (DC) functions by a mechanism(s) that remains unclear. In the present study, Per a 10 protease activity on CD40 expression and downstream signalling was evaluated in DCs. Monocyte-derived DCs from cockroach-allergic patients were treated with proteolytically active/heat-inactivated Per a 10. Stimulation with active Per a 10 demonstrated low CD40 expression on DCs surface (P Per a 10, suggesting cleavage of CD40. Per a 10 activity reduced the interleukin (IL)-12 and interferon (IFN)-γ secretion by DCs (P Per a 10, indicating that low CD40 expression is associated with low levels of IL-12 secretion. Active Per a 10 stimulation caused low nuclear factor-kappa B (NF-κB) activation in DCs compared to heat-inactivated Per a 10. Inhibition of the NF-κB pathway suppressed the CD40 expression and IL-12 secretion by DCs, further indicating that NF-κB is required for CD40 up-regulation. CD40 expression activated the tumour necrosis factor (TNF) receptor-associated factor 6 (TRAF6), thereby suggesting its involvement in NF-κB activation. Protease activity of Per a 10 induced p38 mitogen-activated protein kinase (MAPK) activation that showed no significant effect on CD40 expression by DCs. However, inhibiting p38 MAPK or NF-κB suppressed the secretion of IL-12, IFN-γ, IL-6 and TNF-α by DCs. Such DCs further reduced the secretion of IL-4, IL-6, IL-12 and TNF-α by CD4(+) T cells. In conclusion, protease activity of Per a 10 reduces CD40 expression on DCs. CD40 down-regulation leads to low NF-κB levels, thereby modulating DC-mediated immune responses. © 2014 British Society for Immunology.

Regulation of allergic airway inflammation by adoptive transfer of CD4+ T cells preferentially producing IL-10.

Science.gov (United States)

Matsuda, Masaya; Doi, Kana; Tsutsumi, Tatsuya; Fujii, Shinya; Kishima, Maki; Nishimura, Kazuma; Kuroda, Ikue; Tanahashi, Yu; Yuasa, Rino; Kinjo, Toshihiko; Kuramoto, Nobuyuki; Mizutani, Nobuaki; Nabe, Takeshi

2017-10-05

Anti-inflammatory pharmacotherapy for asthma has mainly depended on the inhalation of glucocorticoids, which non-specifically suppress immune responses. If the anti-inflammatory cytokine interleukin (IL)-10 can be induced by a specific antigen, asthmatic airway inflammation could be suppressed when individuals are exposed to the antigen. The purpose of this study was to develop cellular immunotherapeutics for atopic diseases using IL-10-producing CD4 + T cells. Spleen cells isolated from ovalbumin (OVA)-sensitized mice were cultured with the antigen, OVA and growth factors, IL-21, IL-27 and TGF-β for 7 days. After the 7-day culture, the CD4 + T cells were purified using a murine CD4 magnetic beads system. When the induced CD4 + T cells were stimulated by OVA in the presence of antigen-presenting cells, IL-10 was preferentially produced in vitro. When CD4 + T cells were adoptively transferred to OVA-sensitized mice followed by intratracheal OVA challenges, IL-10 was preferentially produced in the serum and bronchoalveolar lavage fluid in vivo. IL-10 production coincided with the inhibition of eosinophilic airway inflammation and epithelial mucus plugging. Most of the IL-10-producing CD4 + T cells were negative for Foxp3 and GATA-3, transcription factors of naturally occurring regulatory T cells and Th2 cells, respectively, but double positive for LAG-3 and CD49b, surface markers of inducible regulatory T cells, Tr1 cells. Collectively, most of the induced IL-10-producing CD4 + T cells could be Tr1 cells, which respond to the antigen to produce IL-10, and effectively suppressed allergic airway inflammation. The induced Tr1 cells may be useful for antigen-specific cellular immunotherapy for atopic diseases. Copyright © 2017 Elsevier B.V. All rights reserved.

9 CFR 355.10 - Assignment of inspectors.

Science.gov (United States)

2010-01-01

... INSPECTION AND CERTIFICATION CERTIFIED PRODUCTS FOR DOGS, CATS, AND OTHER CARNIVORA; INSPECTION... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Assignment of inspectors. 355.10 Section 355.10 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE...

CD4+ T Cell-derived IL-10 Promotes Brucella abortus Persistence via Modulation of Macrophage Function

Science.gov (United States)

Xavier, Mariana N.; Winter, Maria G.; Spees, Alanna M.; Nguyen, Kim; Atluri, Vidya L.; Silva, Teane M. A.; Bäumler, Andreas J.; Müller, Werner; Santos, Renato L.; Tsolis, Renée M.

2013-01-01

Evasion of host immune responses is a prerequisite for chronic bacterial diseases; however, the underlying mechanisms are not fully understood. Here, we show that the persistent intracellular pathogen Brucella abortus prevents immune activation of macrophages by inducing CD4+CD25+ T cells to produce the anti-inflammatory cytokine interleukin-10 (IL-10) early during infection. IL-10 receptor (IL-10R) blockage in macrophages resulted in significantly higher NF-kB activation as well as decreased bacterial intracellular survival associated with an inability of B. abortus to escape the late endosome compartment in vitro. Moreover, either a lack of IL-10 production by T cells or a lack of macrophage responsiveness to this cytokine resulted in an increased ability of mice to control B. abortus infection, while inducing elevated production of pro-inflammatory cytokines, which led to severe pathology in liver and spleen of infected mice. Collectively, our results suggest that early IL-10 production by CD25+CD4+ T cells modulates macrophage function and contributes to an initial balance between pro-inflammatory and anti-inflammatory cytokines that is beneficial to the pathogen, thereby promoting enhanced bacterial survival and persistent infection. PMID:23818855

9 CFR 114.10 - Antibiotics as preservatives.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Antibiotics as preservatives. 114.10 Section 114.10 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE VIRUSES, SERUMS, TOXINS, AND ANALOGOUS PRODUCTS; ORGANISMS AND VECTORS PRODUCTION REQUIREMENTS FOR...

Growth and Cd uptake by rice (Oryza sativa) in acidic and Cd-contaminated paddy soils amended with steel slag.

Science.gov (United States)

He, Huaidong; Tam, Nora F Y; Yao, Aijun; Qiu, Rongliang; Li, Wai Chin; Ye, Zhihong

2017-12-01

Contamination of rice (Oryza sativa) by Cd is of great concern. Steel slag could be used to amend Cd-contaminated soils and make them safe for cereal production. This work was conducted to study the effects of steel slag on Cd uptake and growth of rice plants in acidic and Cd-contaminated paddy soils and to determine the possible mechanisms behind these effects. Pot (rhizobag) experiments were conducted using rice plants grown on two acidic and Cd-contaminated paddy soils with or without steel slag amendment. Steel slag amendment significantly increased grain yield by 36-45% and root catalase activity, and decreased Cd concentrations in brown rice by 66-77% compared with the control, in both soils. Steel slag amendment also markedly decreased extractable soil Cd, Cd concentrations in pore-water and Cd translocation from roots to above-ground parts. It also significantly increased soil pH, extractable Si and Ca in soils and Ca concentrations in roots. Significant positive correlations were found between extractable soil Cd and Cd concentrations in rice tissues, but it was negatively correlated with soil pH and extractable Si. Calcium in root tissues significantly and negatively correlated with Cd translocation factors from roots to straw. Overall, steel slag amendment not only significantly promoted rice growth but decreased Cd accumulation in brown rice. These benefits appear to be related to improvements in soil conditions (e.g. increasing pH, extractable Si and Ca), a reduction in extractable soil Cd, and suppression of Cd translocation from roots to above-ground parts. Copyright © 2017 Elsevier Ltd. All rights reserved.

Irradiation hardening of Mod.9Cr-1Mo steel

International Nuclear Information System (INIS)

Ryu, Woo-Seog; Kim, Sung-Ho; Choo, Kee-Nam; Kim, Do-Sik

2009-01-01

An irradiation test of Mod.9Cr-1Mo steel was carried out in the OR5 test hole of HANARO of a 30 MW thermal power at 390±10degC up to a fast neutron fluence of 4.4x10 19 (n/cm 2 ) (E > 1.0 MeV). The dpa of the irradiated specimens was evaluated to be 0.034 - 0.07. Tensile and impact tests of the irradiated Mod.9Cr-1Mo were done in the hot cell of the IMEF. The change of the tensile strength by irradiation was similar to the change of the yield strength. The increase of the yield and tensile strengths was up to 18% and 10% respectively. The elongation reduction of the weldment was up to 65%. (author)

Trichoderma reesei FS10-C enhances phytoremediation of Cd-contaminated soil by Sedum plumbizincicola and associated soil microbial activities

Science.gov (United States)

Teng, Ying; Luo, Yang; Ma, Wenting; Zhu, Lingjia; Ren, Wenjie; Luo, Yongming; Christie, Peter; Li, Zhengao

2015-01-01

This study aimed to explore the effects of Trichoderma reesei FS10-C on the phytoremediation of Cd-contaminated soil by the hyperaccumulator Sedum plumbizincicola and on soil fertility. The Cd tolerance of T. reesei FS10-C was characterized and then a pot experiment was conducted to investigate the growth and Cd uptake of S. plumbizincicola with the addition of inoculation agents in the presence and absence of T. reesei FS10-C. The results indicated that FS10-C possessed high Cd resistance (up to 300 mg L-1). All inoculation agents investigated enhanced plant shoot biomass by 6–53% of fresh weight and 16–61% of dry weight and Cd uptake by the shoots by 10–53% compared with the control. All inoculation agents also played critical roles in increasing soil microbial biomass and microbial activities (such as biomass C, dehydrogenase activity and fluorescein diacetate hydrolysis activity). Two inoculation agents accompanied by FS10-C were also superior to the inoculation agents, indicating that T. reesei FS10-C was effective in enhancing both Cd phytoremediation by S. plumbizincicola and soil fertility. Furthermore, solid fermentation powder of FS10-C showed the greatest capacity to enhance plant growth, Cd uptake, nutrient release, microbial biomass and activities, as indicated by its superior ability to promote colonization by Trichoderma. The solid fermentation powder of FS10-C might serve as a suitable inoculation agent for T. reesei FS10-C to enhance both the phytoremediation efficiency of Cd-contaminated soil and soil fertility. PMID:26113858

Effect of rolling temperature on 12Kh18N10T steel tube hardening

International Nuclear Information System (INIS)

Yushkevich, P.M.; Stepanovich, V.E.; Manankova, L.V.; Usenko, V.N.; Semenov, I.A.

1984-01-01

Mechanical properties and substructure of tubes at the constant reduction degree k(the ratio of deformation over wall thickness to deformation over diameter), depending on strain degree during cold and hot tube rolling, have been studied. The investigations are carried out using hot-rolled tubes with the dimensions 88x8 mm of 12Kh1hN10T steel. With the decrease of strain over the wall of the tube, produced of 12Kh18N10T steel as to strain over diameter the values of yield strength and ultimate strength increase with simultaneous decrease in ductility during warm rolling and yield strength and ultimate strength decrease with the increase in ductility-during cold rolling. During warm rolling of the tubes at 250 deg C the hardening of 12Kh18N10T steel is higher, than at the rolling temperature 150 deg C. The optimum temperature range of warm rolling is 120-150 deg C. Grain orientation in the metal of the tubes and degree of texture perfection increase with the temperature increase of the tube warm drolling as compared with col rolli

Structure of steel 8 CrMoNiNb 9 10 and its variations in long-term thermal stress

International Nuclear Information System (INIS)

Fabritius, H.; Schnabel, E.

1976-01-01

On four casts of steel 8 CrMoNiNb 9 10 with about 0.06% C, 0.25; Si, 0.7% Mn, 0.012% N, 0.002 to 0.020% Al, 2.25% Cr, 0.94% Mo, 0.63 to 0.91% Nb and 0.67% Ni, transformation behaviour and structural changes during long-time annealing at 500 to 750 degC lasting up to 30,000 h were studied in unformed condition and after previous cold forming. The carbon content was largely bound in form of primary niobium carbonitrides so that during quenching and tempering low-carbon bainite was formed, or at very slow cooling a ferritic structure without pearlite. Martensite occurred only after fast cooling from temperatures above 1200 degC. Bainite exhibited a very high dislocation density and a large number of coherent niobium carbonitrides. During tempering, the precipitates overaged, and the dislocations started to arrange themselves to subgrain boundaries. Hardness and strength in quenched and tempered condition were essentially governed by dislocation density and size of subgrains. In the whole range of bainite transformation, they are only slightly dependent upon the cooling rate and hence upon the dimensions of the products. The structural changes which occurred in bainitic material during long-time aging and led to a ferritic structure in the final state were interpreted as recovery and recrystallization. In unformed and slightly formed material recrystallization led to a very coarse-grained structure. In highly formed material a very fine-grained structure was achieved by recrystallization. By a high degree of cold forming the recrystallization process was considerably promoted. With an annealing time of 10 5 h, no recrystallization is to be expected for unformed specimens of the studied cast up to 580 degC, but above 650 degC complete recrystallization. (author)

Isolation and characterization of a primary proximal tubular epithelial cell model from human kidney by CD10/CD13 double labeling.

Directory of Open Access Journals (Sweden)

Cynthia Van der Hauwaert

Full Text Available Renal proximal tubular epithelial cells play a central role in renal physiology and are among the cell types most sensitive to ischemia and xenobiotic nephrotoxicity. In order to investigate the molecular and cellular mechanisms underlying the pathophysiology of kidney injuries, a stable and well-characterized primary culture model of proximal tubular cells is required. An existing model of proximal tubular cells is hampered by the cellular heterogeneity of kidney; a method based on cell sorting for specific markers must therefore be developed. In this study, we present a primary culture model based on the mechanical and enzymatic dissociation of healthy tissue obtained from nephrectomy specimens. Renal epithelial cells were sorted using co-labeling for CD10 and CD13, two renal proximal tubular epithelial markers, by flow cytometry. Their purity, phenotypic stability and functional properties were evaluated over several passages. Our results demonstrate that CD10/CD13 double-positive cells constitute a pure, functional and stable proximal tubular epithelial cell population that displays proximal tubule markers and epithelial characteristics over the long term, whereas cells positive for either CD10 or CD13 alone appear to be heterogeneous. In conclusion, this study describes a method for establishing a robust renal proximal tubular epithelial cell model suitable for further experimentation.

9 CFR 54.10 - Tests for scrapie.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Tests for scrapie. 54.10 Section 54.10... tests may be approved for the identification of suspect animals, for the identification of scrapie-positive animals, or for other purposes such as flock certification. For a test to be approved for the...

High expression of TRF2, SOX10, and CD10 in circulating tumor microemboli detected in metastatic melanoma patients. A potential impact for the assessment of disease aggressiveness.

Science.gov (United States)

Long, Elodie; Ilie, Marius; Bence, Coraline; Butori, Catherine; Selva, Eric; Lalvée, Salomé; Bonnetaud, Christelle; Poissonnet, Gilles; Lacour, Jean-Philippe; Bahadoran, Philippe; Brest, Patrick; Gilson, Eric; Ballotti, Robert; Hofman, Véronique; Hofman, Paul

2016-06-01

Circulating tumors cells (CTCs) can be detected in the blood of metastatic melanoma patients (MMPs) both as isolated circulating tumor cells (iCTCs) and circulating tumor microemboli (CTMs), but their clinical significance remains unknown. The aim of this work was to evaluate the prognostic impact in metastatic cutaneous melanoma of CTMs and iCTCs identified by a cytomorphological approach using the isolation by size of tumor cell (ISET) method. We characterized the phenotype of CTCs using anti-PS100, anti-SOX10, anti-CD10, and anti-TRF2 antibodies. 128 MMPs and 37 control healthy individuals with benign nevi were included in this study. Results were compared to the follow-up of patients. 109/128 (85%) MMPs showed CTCs, 44/128 (34%) with 2 to 6 CTMs and 65/128 (51%) with 4 to 9 iCTCs. PS100 expression was homogeneous in iCTCs and heterogeneous in CTMs. SOX10, CD10, and TRF2 were mainly expressed in CTMs. None of the control subjects demonstrated circulating malignant tumor cells. Overall survival was significantly decreased in patients with CTMs, independently of the therapeutic strategies. In conclusion, the presence of CTMs is an independent predictor of shorter survival from the time of diagnosis of MMPs. © 2016 The Authors. Cancer Medicine published by John Wiley & Sons Ltd.

10 CFR 9.109 - Report to Congress.

Science.gov (United States)

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Report to Congress. 9.109 Section 9.109 Energy NUCLEAR REGULATORY COMMISSION PUBLIC RECORDS Government in the Sunshine Act Regulations § 9.109 Report to Congress. The Secretary shall annually report to the Congress regarding the Commission's compliance with the...

Aminoacid N-substituted 1,4,7-triazacyclononane and 1,4,7,10-tetraazacyclododecane Zn2+, Cd2+ and Cu2+ complexes. A preparative, potentiometric titration and NMR spectroscopic study.

Science.gov (United States)

Plush, Sally E; Lincoln, Stephen F; Wainwright, Kevin P

2004-05-07

The pK(a)s and Zn2+, Cd2+ and Cu2+ complexation constants (K) for 1,4,7-tris[(2''S)-acetamido-2''-(methyl-3''-phenylpropionate)]-1,4,7-triazacyclononane, 1, 1,4,7-tris[(2''S)-acetamido-2''-(1''-carboxy-3''-phenylpropane)]-1,4,7-triazacyclononane, H(3)2, 1,4,7-tris[(2''S)-acetamido-2''-(methyl-3''-(1H-3-indolyl)propionate)]-1,4,7-triazacyclononane, 3, and 1,4,7,10-tetrakis[(2''S)-acetamido-2''-(methyl-3''-phenylpropionate)]-1,4,7,10-tetraazacyclododecane, 4, 1,4,7,10-tetrakis[(2''S)-acetamido-2''-(1''-carboxy-3''-phenylpropane)]-1,4,7,10-tetraazacyclododecane, H(4)5, in 20 : 80 v/v water-methanol solution are reported. The pK(a)s within the potentiometric detection range for H(3)1(3+) = 8.69 and 3.59, for H(6)2(3+) = 9.06, 6.13, 4.93 and 4.52, H(3)3(3+) = 8.79 and 3.67, H(4)4(4+) = 8.50, 5.62 and 3.77 and for H(8)5(4+) = 9.89, 7.06, 5.53, 5.46, 4.44 and 4.26 where each tertiary amine nitrogen is protonated. The complexes of 1: [Zn(1)]2+(9.00), [Cd(1)]2+ (6.49), [Cd(H1)]3+ (4.54) and [Cu(1)]2+ (10.01) are characterized by the log(K/dm3 mol(-1)) values shown in parentheses. Analogous complexes are formed by 3 and 4: [Zn(3)]2+ (10.19), [Cd(3)]2+ (8.54), [Cu(3)]2+ (10.77), [Zn(4)]2+ (11.41) [Cd(4)]2+ (9.16), [Cd(H4)]3+ (6.16) and [Cu(4)]2+ (11.71). The tricarboxylic acid H(3)2 generates a greater variety of complexes as exemplified by: [Zn(2)-] (10.68) [Zn(H2)] (6.60) [Zn(H(2)2)+] (5.15), [Cd(2)](-) (4.99), [Cd(H2)] (4.64), [Cd(H2(2))]+ (3.99), [Cd(H(3)2)]2+ (3.55), [Cu(2)](-) (12.55) [Cu(H2)] (7.66), [Cu(H(2)2)]+ (5.54) and [Cu(2)2](4-) (3.23). The complexes of H(4)5 were insufficiently soluble to study in this way. The 1H and 13C NMR spectra of the ligands are consistent with formation of a predominant Zn2+ and Cd2+ Delta or Lambda diastereomer. The preparations of the new pendant arm macrocycles H(3)2, 3, 4 and H(4)5 are reported.

Niclosamide, an oral antihelmintic drug, exhibits antimetastatic activity in hepatocellular carcinoma cells through downregulating twist-mediated CD10 expression.

Science.gov (United States)

Chien, Ming-Hsien; Ho, Yung-Chuan; Yang, Shun-Fa; Yang, Yi-Chieh; Lai, Szu-Yu; Chen, Wan-Shen; Chen, Ming-Jenn; Yeh, Chao-Bin

2018-02-26

Hepatocellular carcinoma (HCC) is one of the most common malignancies in the world, especially, in eastern Asia, and its prognosis is poor once metastasis occurs. Niclosamide, a US Food and Drug Administration-approved antihelmintic drug, was shown to inhibit the growth of various cancers including HCC, but the effect of niclosamide on cell motility and the underlying mechanism have not yet been completely defined. The present study demonstrated that niclosamide, at 0-40 nM, concentration-dependently inhibited wound closure and the migratory/invasive capacities of human Huh7 and SK-Hep-1 HCC cells without exhibiting cytotoxicity. A protease array analysis showed that CD10 was dramatically downregulated in Huh7 cells after niclosamide treatment. Western blot and flow cytometric assays further demonstrated that CD10 expression was concentration-dependently downregulated in Huh7 and SK-Hep-1 cells after niclosamide treatment. Mechanistic investigations found that niclosamide suppressed Twist-mediated CD10 transactivation. Moreover, knockdown of CD10 expression by CD10 small interfering RNA in HCC cells suppressed cell migratory/invasive abilities and overexpression of CD10 relieved the migration inhibition induced by niclosamide. Taken together, our results indicated that niclosamide could be a potential agent for inhibiting metastasis of HCC, and CD10 is an important target of niclosamide for suppressing the motility of HCC cells. © 2018 Wiley Periodicals, Inc.

Electrochemical characterisation of X10CrNi 18-8 steel in artificial plasma

Directory of Open Access Journals (Sweden)

J. Przondziono

2015-01-01

Full Text Available Quality of applied guide wires conditions the course of treatment and its success to a great extent. In order to simulate conditions that can be found in blood vascular system samples were exposed to artificial blood plasma (T = 37 } 1 oC for the time of 8 h. In order to obtain information regarding physical and chemical properties of modified surface of wire made of X10CrNi 18-8 steel, electrochemical impedance spectroscopy (EIS test and tests of chemical composition of the surface layer X-ray photoelectron spectroscopy (XPS were made. On the ground of performed EIS and XPS tests, favourable impact of steam sterilisation process on corrosion resistance of X10CrNi 18-8 steel was observed only for the case when chemical passivation was applied prior to sterilisation.

Hydrogen effect on mechanical properties and flake formation in the 10KhSND steel rolled plates

Energy Technology Data Exchange (ETDEWEB)

Muradova, R G; Zakharov, V A; Kuzin, A P; Gol' tsov, V A; Podgajskij, M S [Donetskij Politekhnicheskij Inst. (Ukrainian SSR); Donetskij Nauchno-Issledovatel' skij Inst. Chernoj Metallurgii (Ukrainian SSR))

1982-01-01

The effect of hydrogen on mechanical properties of the 10KhSND steel rolled plates during natural aging is studied. Optimum period of metal acceptance tests, which are advisable to conduct after 5-7 day natural aging of finished products, are found out. The technique is worked out and a safe hydrogen content to prevent flake formation in the 10KhSND steel is determined. It is shown that a safe hydrogen content is dependent on the experiment conditions (sample dimensions, conditions of cooling, and prehistory).

Hydrogen effect on mechanical properties and flake formation in the 10KhSND steel rolled plates

International Nuclear Information System (INIS)

Muradova, R.G.; Zakharov, V.A.; Kuzin, A.P.; Gol'tsov, V.A.; Podgajskij, M.S.

1982-01-01

The effect of hydrogen on mechanical properties of the 10KhSND steel rolled plates during natural aging is studied. Optimum period of metal acceptance tests, which are advisable to conduct after 5-7 day natural aging of finished products, are found out. The technique is worked out and a safe hydrogen content to prevent flake formation in the 10KhSND steel is determined. It is shown that a safe hydrogen content is dependent on the experiment conditions (sample dimensions, conditions of cooling, and prehistory)

Microstructural evolution of HFIR-irradiated low activation F82H and F82H-10B steels

International Nuclear Information System (INIS)

Wakai, E.; Shiba, K.; Sawai, T.; Hashimoto, N.; Robertson, J.P.; Klueh, R.L.

1998-01-01

Microstructures of reduced-activation F82H (8Cr-2W-0.2V-0.04Ta) and the F82H steels doped with 10 B, irradiated at 250 and 300 C to 3 and 57 dpa in the High Flux Isotope Reactor (HFIR), were examined by TEM. In the F82H irradiated at 250 C to 3 dpa, dislocation loops, small unidentified defect clusters with a high number density, and a few MC precipitates were observed in the matrix. The defect microstructure after 300 C irradiation to 57 dpa is dominated by the loops, and the number density of loops was lower than that of the F82H- 10 B steel. Cavities were observed in the F82H- 10 B steels, but the swelling value is insignificant. Small particles of M 6 C formed on the M 23 C 6 carbides that were present in both steels before the irradiation at 300 C to 57 dpa. A low number density of MC precipitate particles formed in the matrix during irradiation at 300 C to 57 dpa

Ultrasound surface treatment of Kh18N10T steel with different structural state. Ul'trazvukovaya poverkhnostnaya obrabotka stali Kh18N10T s razlichnym strukturnym sostoyaniem

Energy Technology Data Exchange (ETDEWEB)

Aksenov, V K; Danilov, P A; Mats, A V; Netesov, V M; Yaes, A A [AN Ukrainskoj SSR, Kharkov (Ukrainian SSR). Fiziko-Tekhnicheskij Inst.

1989-09-01

Ultrasound surface treatment (USST) is studied for its effect on the structure and mechanical-and-physical properties of Kh18N10T steel with different prehistory. It is shown that surface treatment may both increase and decrease steel microhardness.

The effect of refurbishing a UK steel plant on PM10 metal composition and ability to induce inflammation

Directory of Open Access Journals (Sweden)

Maynard Robert L

2005-05-01

Full Text Available Abstract Background In the year 2000 Corus closed its steel plant operations in Redcar, NE of England temporarily for refurbishment of its blast furnace. This study investigates the impact of the closure on the chemical composition and biological activity of PM10 collected in the vicinity of the steel plant. Methods The metal content of PM10 samples collected before during and after the closure was measured by ICP-MS in order to ascertain whether there was any significant alteration in PM10 composition during the steel plant closure. Biological activity was assessed by instillation of 24 hr PM10 samples into male Wistar rats for 18 hr (n = 6. Inflammation was identified by the cellular and biochemical profile of the bronchoalveolar lavage fluid. Metal chelation of PM10 samples was conducted using Chelex beads prior to treatment of macrophage cell line, J774, in vitro and assessment of pro-inflammatory cytokine expression. Results The total metal content of PM10 collected before and during the closure period were similar, but on reopening of the steel plant there was a significant 3-fold increase (p 10 collected during the reopened period, as well as significant increases in albumin (p 10 from the pre-closure and closure periods did not induce any significant alterations in inflammation or lung damage. The soluble and insoluble extractable PM10 components washed from the reopened period both induced a significant increase in neutrophil cell number (p 10 from the re-opened period stimulated J774 macrophages to generate TNF-α protein and this was significantly prevented by chelating the metal content of the PM10 prior to addition to the cells. Conclusion PM10-induced inflammation in the rat lung was related to the concentration of metals in the PM10 samples tested, and activity was found in both the soluble and insoluble fractions of the particulate pollutant.

A new 9,10-dihydrophenanthrene from Dendrobium moniliforme.

Science.gov (United States)

Zhao, Ningdong; Yang, Guangyu; Zhang, Yan; Chen, Lijun; Chen, Yegao

2016-01-01

A new 9,10-dihydrophenanthrene,1,5-dihydroxy-3,4,7-trimethoxy-9,10-dihydrophenanthrene (1) was isolated and identified from the whole plants of Dendrobium moniliforme, as well as 24 known compounds including hircinol (2), (2R*,3S*)-3-hydroxymethyl-9-methoxy-2-(4'-hydroxy-3',5'-dimethoxyphenyl)-2,3,6,7-tetrahydro-phenanthro[4,3-b]furan-5,11-diol (3), diospyrosin (4), aloifol I (5), moscatilin (6), 3,4'-dihydroxy-3',4,5-trimethoxybibenzyl (7), gigantol (8), 3,3'-dihydroxy-4,5-dimethoxybibenzyl (9), longicornuol A (10), N-trans-cinnamoyltyramine (11), paprazine (12), N-trans-feruloyl 3'-O-methyldopamine (13), moupinamide (14), dihydroconiferyl dihydro-p-coumarate (15), dihydrosinapyl dihydro-p-coumarate (16), 3-isopropyl-5-acetoxycyclohexene-2-one-1 (17), p-hydroxybenzaldehyde (18), vanillin (19), p-hydroxyphenylpropionic acid (20), vanillic acid (21), protocatechuic acid (22), (+)-syringaresinol (23), β-sitosterol (24) and daucosterol (25). Compounds 3, 4, 13, 16, 17 and 20 were isolated from the Dendrobium genus for the first time, and compounds 2, 5, 7, 9-12, 14, 15, 18, 21 and 22 were originally obtained from D. moniliforme.

Efficient and stable single-dopant white OLEDs based on 9,10-bis (2-naphthyl) anthracene

International Nuclear Information System (INIS)

Tao Silu; Peng Zhaokuai; Zhang Xiaohong; Wu Shikang

2006-01-01

Efficient white organic light-emitting diodes (WOLEDs) are fabricated with a thin layer of 9,10-bis (2-naphthyl) anthracene (ADN) doped with Rubrene as the source of white emission. A device with the structure of ITO/NPB (70nm)/ADN: 0.5% Rubrene (30nm)/Alq 3 (50nm)/MgAg shows a maximum current efficiency of 3.7cd/A, with the CIE coordinates of x=0.33, y=0.43. The EL spectrum of the devices and the CIE coordinates remains almost the same when the voltage is increased from 10 to 15V and the current efficiency remains quite stable with the current density increased from 20 to 250mA/cm 2

Tribocorrosion behaviour of 08CH18N10T steel

International Nuclear Information System (INIS)

Kubecka, P.; Tvrdy, M.; Wenger, F.; Ponthiaux, P.

2000-01-01

Tribocorrosion of the 08CH18N10T austenitic stainless steel in a potassium sulphate solution was investigated with the help of pin-on-disk tribometer and polarisation curves method. The results indicate the occurrence of synergetic interactions between electrochemical and mechanical conditions: the damaging of the passive film by friction was pointed out, leading to an increase in the dissolution rate of the metal and simultaneously, the occurrence of electrochemical reactions (gas evolution, dissolution, passivation) was found to modify the tribological conditions (friction coefficient). (author)

Shedding of CD9 antigen into cerebrospinal fluid by acute lymphoblastic leukemia cells.

Science.gov (United States)

Komada, Y; Ochiai, H; Shimizu, K; Azuma, E; Kamiya, H; Sakurai, M

1990-07-01

The accurate identification of small numbers of leukemic cells in the cerebrospinal fluid (CSF) presents a diagnostic problem in the treatment of acute lymphoblastic leukemia (ALL). We demonstrated that soluble CD9 antigen was shed into CSF obtained from children with ALL, using enzyme-linked immunosorbent assay (ELISA), which used the activity of CD9 antigen to bind the Ricinus communis agglutinin (RCA1) and a monoclonal antibody, SJ-9A4, simultaneously. Using RCA1/SJ-9A4 ELISA, CD9 antigen was detectable in CSF but not in plasma from 12 cases of CD9+ ALL in central nervous system (CNS) relapse. However, CD9 antigen was not released into CSF from 11 cases of CD9- ALL with CNS involvement, 136 cases of CD9+ ALL in complete remission (CR), 29 cases of CD9- ALL in CR, or 21 cases of aseptic meningitis. Interestingly, the levels of CD9 antigen were elevated in CSF from 7 of 10 CD9+ ALL patients without cytologically proven CNS involvement at diagnosis, with subsequent return to undetectable levels after initial induction chemotherapy was begun. In addition, sequential analysis of CSF from a 5-year-old boy with CD9+ ALL in CNS relapse showed that levels of CD9 antigen correlated well with the number of leukemic cells in CSF. Serial quantitative analysis of CD9 antigen in CSF could be useful to detect the proliferation of residual leukemic cells before the clinical manifestation.

CD10-/ALDH- cells are the sole cisplatin-resistant component of a novel ovarian cancer stem cell hierarchy.

Science.gov (United States)

Ffrench, Brendan; Gasch, Claudia; Hokamp, Karsten; Spillane, Cathy; Blackshields, Gordon; Mahgoub, Thamir Mahmoud; Bates, Mark; Kehoe, Louise; Mooney, Aoibhinn; Doyle, Ronan; Doyle, Brendan; O'Donnell, Dearbhaile; Gleeson, Noreen; Hennessy, Bryan T; Stordal, Britta; O'Riain, Ciaran; Lambkin, Helen; O'Toole, Sharon; O'Leary, John J; Gallagher, Michael F

2017-10-19

It is long established that tumour-initiating cancer stem cells (CSCs) possess chemoresistant properties. However, little is known of the mechanisms involved, particularly with respect to the organisation of CSCs as stem-progenitor-differentiated cell hierarchies. Here we aimed to elucidate the relationship between CSC hierarchies and chemoresistance in an ovarian cancer model. Using a single cell-based approach to CSC discovery and validation, we report a novel, four-component CSC hierarchy based around the markers cluster of differentiation 10 (CD10) and aldehyde dehydrogenase (ALDH). In a change to our understanding of CSC biology, resistance to chemotherapy drug cisplatin was found to be the sole property of CD10 - /ALDH - CSCs, while all four CSC types were sensitive to chemotherapy drug paclitaxel. Cisplatin treatment quickly altered the hierarchy, resulting in a three-component hierarchy dominated by the cisplatin-resistant CD10 - /ALDH - CSC. This organisation was found to be hard-wired in a long-term cisplatin-adapted model, where again CD10 - /ALDH - CSCs were the sole cisplatin-resistant component, and all CSC types remained paclitaxel-sensitive. Molecular analysis indicated that cisplatin resistance is associated with inherent- and adaptive-specific drug efflux and DNA-damage repair mechanisms. Clinically, low CD10 expression was consistent with a specific set of ovarian cancer patient samples. Collectively, these data advance our understanding of the relationship between CSC hierarchies and chemoresistance, which was shown to be CSC- and drug-type specific, and facilitated by specific and synergistic inherent and adaptive mechanisms. Furthermore, our data indicate that primary stage targeting of CD10 - /ALDH - CSCs in specific ovarian cancer patients in future may facilitate targeting of recurrent disease, before it ever develops.

Microstructural change during creep deformation in a 10%Cr martensitic steel

International Nuclear Information System (INIS)

Kim, Sung Ho; Song, B. J.; Ryu, Woo Seog

2001-01-01

The relationship between creep deformation and microstructural changes in martensitic 10Cr-MoW steel has been studied. Transmission electron microscopy and image analyser were used to determine the variation of precipitates and martensite lath width size during creep deformation and aging. As precipitates are coarsened during creep deformation, dislocations become easy to move and the recovery proceeds rapidly. This leads to the growth of lath width. The average size of precipitates was linearly increased with creep time. On the other hand the growth rate of lath width is constant until tertiary creep, but the growth of lath width is accelerated during tertiary creep. It has been concluded that the growth behavior of lath width are consistent with creep deformation. Because the growth of lath width is controlled by the coarsening of precipitates it is important to form more stable precipitates in creep condition for improvement of creep properties of martensitic steel. Microstructure of martensitic steel is thermally very stable, so the size of precipitates and martensite lath width are hardly changed during aging

10 CFR 451.9 - Procedures for processing applications.

Science.gov (United States)

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Procedures for processing applications. 451.9 Section 451.9 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION RENEWABLE ENERGY PRODUCTION INCENTIVES § 451.9... or operators of qualified renewable energy facilities using solar, wind, ocean, geothermal, and...

9 CFR 73.10 - Permitted dips; substances allowed.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Permitted dips; substances allowed. 73.10 Section 73.10 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT... flowers of sulphur or sulphur flour to 100 gallons of water; or a specifically permitted proprietary brand...

9 CFR 124.10 - APHIS liaison with PTO.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false APHIS liaison with PTO. 124.10 Section 124.10 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF... period was the first permitted commercial marketing or use of the product under the provision of law...

IL10-Deficiency in CD4+ T Cells Exacerbates the IFNγ and IL17 Response During Bacteria Induced Colitis

Directory of Open Access Journals (Sweden)

Virginia Seiffart

2015-07-01

Full Text Available Background/Aims: IL10 is a key inhibitor of effector T cell activation and a mediator of intestinal homeostasis. In addition, IL10 has emerged as a key immunoregulator during infection with various pathogens, ameliorating the excessive T-cell responses that are responsible for much of the immunopathology associated with the infection. Because IL10 plays an important role in both intestinal homeostasis and infection, we studied the function of IL10 in infection-associated intestinal inflammation. Methods: Wildtype mice and mice deficient in CD4+ T cell-derived or regulatory T cells-derived IL10 were infected with the enteric pathogen Citrobacter (C. rodentium and analyzed for the specific immune response and pathogloy in the colon. Results: We found that IL10 expression is upregulated in colonic tissue after infection with C. rodentium, especially in CD4+ T cells, macrophages and dendritic cells. Whereas the deletion of IL10 in regulatory T cells had no effect on C. rodentium induced colitis, infection of mice deficient in CD4+ T cell-derived IL10 exhibited faster clearance of the bacterial burden but worse colitis, crypt hyperplasia, and pathology than did WT mice. In addition, the depletion of CD4+ T cell-derived IL10 in infected animals was accompanied by an accelerated IFNγ and IL17 response in the colon. Conclusion: Thus, we conclude that CD4+ T cell-derived IL10 is strongly involved in the control of C. rodentium-induced colitis. Interference with this network could have implications for the treatment of infection-associated intestinal inflammation.

The influence of interstitial impurities on temperature ranges of deuterium retention in austenitic stainless steel 18Cr10NiTi

International Nuclear Information System (INIS)

Neklyudov, I.M.; Morozov, O.M.; Kulish, V.G.; Zhurba, V.I.; Galytsky, A.G.; Piatenko, E.V.

2009-01-01

The influence of nitrogen, oxygen and helium on the temperature range of deuterium retention in 18Cr10NiTi stainless steel (of AISI304L type) has been investigated. It is demonstrated that the introduction of oxygen, nitrogen or helium into 18Cr10NiTi steel extends the upper limit in the high-temperature range of deuterium retention. It has been found that for 18Cr10NiTi stainless steel, pre-irradiated with helium ions, the increase in the temperature range of deuterium retention occurs in steps: on attainment of helium concentration of ∼0.5 at.% He the temperature range increases by ∼100 K, and on attainment of helium concentration of ∼2.5 at.% He the temperature range increases by ∼350 K. The introduction of oxygen into 18Cr10NiTi stainless steel results in the increase of the temperature range of deuterium retention in the direction of rise in temperature. In the deuterium thermodesorption spectrum, this manifests itself by the occurrence of an additional low-amplitude peak with the maximum temperature T m ∼ 560 K. The introduction of nitric impurity into 18Cr10NiTi stainless steel results in the extension of the temperature range of deuterium retention towards higher temperatures.

Exposure to 9,10-phenanthrenequinone accelerates malignant progression of lung cancer cells through up-regulation of aldo-keto reductase 1B10

International Nuclear Information System (INIS)

Matsunaga, Toshiyuki; Morikawa, Yoshifumi; Haga, Mariko; Endo, Satoshi; Soda, Midori; Yamamura, Keiko; El-Kabbani, Ossama; Tajima, Kazuo; Ikari, Akira; Hara, Akira

2014-01-01

Inhalation of 9,10-phenanthrenequinone (9,10-PQ), a major quinone in diesel exhaust, exerts fatal damage against a variety of cells involved in respiratory function. Here, we show that treatment with high concentrations of 9,10-PQ evokes apoptosis of lung cancer A549 cells through production of reactive oxygen species (ROS). In contrast, 9,10-PQ at its concentrations of 2 and 5 μM elevated the potentials for proliferation, invasion, metastasis and tumorigenesis, all of which were almost completely inhibited by addition of an antioxidant N-acetyl-L-cysteine, inferring a crucial role of ROS in the overgrowth and malignant progression of lung cancer cells. Comparison of mRNA expression levels of six aldo-keto reductases (AKRs) in the 9,10-PQ-treated cells advocated up-regulation of AKR1B10 as a major cause contributing to the lung cancer malignancy. In support of this, the elevation of invasive, metastatic and tumorigenic activities in the 9,10-PQ-treated cells was significantly abolished by the addition of a selective AKR1B10 inhibitor oleanolic acid. Intriguingly, zymographic and real-time PCR analyses revealed remarkable increases in secretion and expression, respectively, of matrix metalloproteinase 2 during the 9,10-PQ treatment, and suggested that the AKR1B10 up-regulation and resultant activation of mitogen-activated protein kinase cascade are predominant mechanisms underlying the metalloproteinase induction. In addition, HPLC analysis and cytochrome c reduction assay in in vitro 9,10-PQ reduction by AKR1B10 demonstrated that the enzyme catalyzes redox-cycling of this quinone, by which ROS are produced. Collectively, these results suggest that AKR1B10 is a key regulator involved in overgrowth and malignant progression of the lung cancer cells through ROS production due to 9,10-PQ redox-cycling. - Highlights: • 9,10-PQ promotes invasion, metastasis and tumorigenicity in lung cancer cells. • The 9,10-PQ-elicited promotion is possibly due to AKR1B10 up

Exposure to 9,10-phenanthrenequinone accelerates malignant progression of lung cancer cells through up-regulation of aldo-keto reductase 1B10

Energy Technology Data Exchange (ETDEWEB)

Matsunaga, Toshiyuki, E-mail: matsunagat@gifu-pu.ac.jp [Laboratory of Biochemistry, Gifu Pharmaceutical University, Gifu 501-1196 (Japan); Morikawa, Yoshifumi; Haga, Mariko; Endo, Satoshi [Laboratory of Biochemistry, Gifu Pharmaceutical University, Gifu 501-1196 (Japan); Soda, Midori; Yamamura, Keiko [Laboratory of Clinical Pharmacy, School of Pharmacy, Aichi Gakuin University, Nagoya 464-8650 (Japan); El-Kabbani, Ossama [Monash Institute of Pharmaceutical Sciences, Monash University, Victoria 3052 (Australia); Tajima, Kazuo [Faculty of Pharmaceutical Sciences, Hokuriku University, Kanazawa 920-1181 (Japan); Ikari, Akira [Laboratory of Biochemistry, Gifu Pharmaceutical University, Gifu 501-1196 (Japan); Hara, Akira [Faculty of Engineering, Gifu University, Gifu 501-1193 (Japan)

2014-07-15

Inhalation of 9,10-phenanthrenequinone (9,10-PQ), a major quinone in diesel exhaust, exerts fatal damage against a variety of cells involved in respiratory function. Here, we show that treatment with high concentrations of 9,10-PQ evokes apoptosis of lung cancer A549 cells through production of reactive oxygen species (ROS). In contrast, 9,10-PQ at its concentrations of 2 and 5 μM elevated the potentials for proliferation, invasion, metastasis and tumorigenesis, all of which were almost completely inhibited by addition of an antioxidant N-acetyl-L-cysteine, inferring a crucial role of ROS in the overgrowth and malignant progression of lung cancer cells. Comparison of mRNA expression levels of six aldo-keto reductases (AKRs) in the 9,10-PQ-treated cells advocated up-regulation of AKR1B10 as a major cause contributing to the lung cancer malignancy. In support of this, the elevation of invasive, metastatic and tumorigenic activities in the 9,10-PQ-treated cells was significantly abolished by the addition of a selective AKR1B10 inhibitor oleanolic acid. Intriguingly, zymographic and real-time PCR analyses revealed remarkable increases in secretion and expression, respectively, of matrix metalloproteinase 2 during the 9,10-PQ treatment, and suggested that the AKR1B10 up-regulation and resultant activation of mitogen-activated protein kinase cascade are predominant mechanisms underlying the metalloproteinase induction. In addition, HPLC analysis and cytochrome c reduction assay in in vitro 9,10-PQ reduction by AKR1B10 demonstrated that the enzyme catalyzes redox-cycling of this quinone, by which ROS are produced. Collectively, these results suggest that AKR1B10 is a key regulator involved in overgrowth and malignant progression of the lung cancer cells through ROS production due to 9,10-PQ redox-cycling. - Highlights: • 9,10-PQ promotes invasion, metastasis and tumorigenicity in lung cancer cells. • The 9,10-PQ-elicited promotion is possibly due to AKR1B10 up

Welding of high-strength stainless steel 03Kh12N10MT for cryogenic engineering

International Nuclear Information System (INIS)

Pustovit, A.I.

1989-01-01

Consideration is being given to weld resistance to cold and hot cracking at 93 and 77K and to mechanical properties of welded joints of high-strength stainless steel 03Kh12N10MT, produced under the fluxes AN-17M, AN-18, AN-26, AN-45, ANF-5, 48-OF-6, ANK-45 and ANK-49 in combination with various welding wires. It is shown that welds on 03Kh12N10MT steel meet the requirements only when using 48-OF-6 or ANK-49 flux. It is noted that impact strength of welds at 77K is sufficiently affected by the volume fraction of non-metallic inclusions in weld metal

OP9 Feeder Cells Are Superior to M2-10B4 Cells for the Generation of Mature and Functional Natural Killer Cells from Umbilical Cord Hematopoietic Progenitors

Directory of Open Access Journals (Sweden)

Lara Herrera

2017-06-01

Full Text Available Adoptive natural killer (NK cell therapy relies on the acquisition of large numbers of mature and functional NK cells. An option for future immunotherapy treatments is to use large amounts of NK cells derived and differentiated from umbilical cord blood (UCB CD34+ hematopoietic stem cells (HSCs, mainly because UCB is one of the most accessible HSC sources. In our study, we compared the potential of two stromal cell lines, OP9 and M2-10B4, for in vitro generation of mature and functional CD56+ NK cells from UCB CD34+ HSC. We generated higher number of CD56+ NK cells in the presence of the OP9 cell line than when they were generated in the presence of M2-10B4 cells. Furthermore, higher frequency of CD56+ NK cells was achieved earlier when cultures were performed with the OP9 cells than with the M2-10B4 cells. Additionally, we studied in detail the maturation stages of CD56+ NK cells during the in vitro differentiation process. Our data show that by using both stromal cell lines, CD34+ HSC in vitro differentiated into the terminal stages 4–5 of maturation resembled the in vivo differentiation pattern of human NK cells. Higher frequencies of more mature NK cells were reached earlier by using OP9 cell line than M2-10B4 cells. Alternatively, we observed that our in vitro NK cells expressed similar levels of granzyme B and perforin, and there were no significant differences between cultures performed in the presence of OP9 cell line or M2-10B4 cell line. Likewise, degranulation and cytotoxic activity against K562 target cells were very similar in both culture conditions. The results presented here provide an optimal strategy to generate high numbers of mature and functional NK cells in vitro, and point toward the use of the OP9 stromal cell line to accelerate the culture procedure to obtain them. Furthermore, this method could establish the basis for the generation of mature NK cells ready for cancer immunotherapy.

High Levels of IL-10 and CD4+CD25hi+ Treg Cells in Endemic Burkitt's Lymphoma Patients.

Science.gov (United States)

Futagbi, Godfred; Gyan, Ben; Nunoo, Harriet; Tetteh, John K A; Welbeck, Jennifer E; Renner, Lorna Awo; Ofori, Michael; Dodoo, Daniel; Edoh, Dominic A; Akanmori, Bartholomew D

2015-08-04

The interplay between Epstein-Barr virus infection, malaria, and endemic Burkitt's Lymphoma is not well understood. Reports show diminished EBV-specific Th1 responses in children living in malaria endemic areas and deficiency of EBNA1-specific IFN-γ T cell responses in children with endemic Burkitt's Lymphoma (eBL). This study, therefore, examined some factors involved in the loss of EBNA-1-specific T cell responses in eBL. T-cell subset frequencies, activation, and IFN-γ- or IL-4-specific responses were analyzed by flow-cytometry. Plasma cytokine levels were measured by ELISA. CD4+ and CD8+ cells in age- and sex-matched healthy controls ( n = 3) expressed more IFN-γ in response to all immunostimulants than in pediatric endemic BL (eBL) patients ( n = 4). In healthy controls, IFN-γ expression was higher than IL-4 expression, whereas in eBL patients the expression of IL-4 by CD4+ cells to EBNA-1 was slightly higher than IFN-γ. Moreover, the blood levels of TNF-α was significantly lower ( p = 0.004) while IL-10 was significantly higher ( p = 0.038), in eBL patients ( n = 21) compared to controls ( n = 16). Additionally, the frequency of CD4+CD25hi+ T cells was higher in both age-matched acute uncomplicated malaria ( n = 26) and eBL ( n = 14) patients compared to healthy controls ( n = 19; p = 0.000 and p = 0.027, respectively). The data suggest that reduced Th1 response in eBL might be due to increased levels of IL-10 and T reg cells.

Microstructure of a high boron 9-12% chromium steel

Energy Technology Data Exchange (ETDEWEB)

Andren, H.O. [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Applied Physics

2008-07-01

Additions of small amounts of boron (10-100 ppm) to 9-12% chromium steels are often made since they have been found to be beneficial for the creep strength up to and above 600 C. The effect of boron is to restrict the coarsening of M{sub 23}C{sub 6} precipitates during service. It was found that increasing the boron content from 9 to 40 ppm gave a decrease in coarsening constant at 600 C by a factor of 2. The present understanding of boron solution, non-equilibrium grain boundary segregation, incorporation into M{sub 23}C{sub 6}, and diffusion is reviewed in the paper. A very high boron addition (300 ppm) was made in the trial TAF steel already in the 1950'ies. The microstructure of a similar trial steel, FT3B, has been studied detail. In this steel large Mo, Cr, Fe and V containing metal borides are formed rather than the expected BN, with the crystal structure M{sub 2}B{sub 2}. Nitrogen is therefore still available for the formation of VN. Due to tempering at a low temperature (690 C) to a high strength (830 MPa), this steel contained a dense distribution of very small VN precipitates, 5-15 nm in size. A similar VN distribution is probably the cause of the still unsurpassed creep strength of the TAF steel. (orig.)

IL-10-produced by human transitional B-cells down-regulates CD86 expression on B-cells leading to inhibition of CD4+T-cell responses.

Science.gov (United States)

Nova-Lamperti, Estefania; Fanelli, Giorgia; Becker, Pablo D; Chana, Prabhjoat; Elgueta, Raul; Dodd, Philippa C; Lord, Graham M; Lombardi, Giovanna; Hernandez-Fuentes, Maria P

2016-01-22

A novel subset of human regulatory B-cells has recently been described. They arise from within the transitional B-cell subpopulation and are characterised by the production of IL-10. They appear to be of significant importance in regulating T-cell immunity in vivo. Despite this important function, the molecular mechanisms by which they control T-cell activation are incompletely defined. Here we show that transitional B-cells produced more IL-10 and expressed higher levels of IL-10 receptor after CD40 engagement compared to other B-cell subsets. Furthermore, under this stimulatory condition, CD86 expressed by transitional B-cells was down regulated and T-cell proliferation was reduced. We provide evidence to demonstrate that the down-regulation of CD86 expression by transitional B-cells was due to the autocrine effect of IL-10, which in turn leads to decreased T-cell proliferation and TNF-α production. This analysis was further extended to peripheral B-cells in kidney transplant recipients. We observed that B-cells from patients tolerant to the graft maintained higher IL-10 production after CD40 ligation, which correlates with lower CD86 expression compared to patients with chronic rejection. Hence, the results obtained in this study shed light on a new alternative mechanism by which transitional B-cells inhibit T-cell proliferation and cytokine production.

IL-10-produced by human transitional B-cells down-regulates CD86 expression on B-cells leading to inhibition of CD4+T-cell responses

Science.gov (United States)

Nova-Lamperti, Estefania; Fanelli, Giorgia; Becker, Pablo D.; Chana, Prabhjoat; Elgueta, Raul; Dodd, Philippa C.; Lord, Graham M.; Lombardi, Giovanna; Hernandez-Fuentes, Maria P.

2016-01-01

A novel subset of human regulatory B-cells has recently been described. They arise from within the transitional B-cell subpopulation and are characterised by the production of IL-10. They appear to be of significant importance in regulating T-cell immunity in vivo. Despite this important function, the molecular mechanisms by which they control T-cell activation are incompletely defined. Here we show that transitional B-cells produced more IL-10 and expressed higher levels of IL-10 receptor after CD40 engagement compared to other B-cell subsets. Furthermore, under this stimulatory condition, CD86 expressed by transitional B-cells was down regulated and T-cell proliferation was reduced. We provide evidence to demonstrate that the down-regulation of CD86 expression by transitional B-cells was due to the autocrine effect of IL-10, which in turn leads to decreased T-cell proliferation and TNF-α production. This analysis was further extended to peripheral B-cells in kidney transplant recipients. We observed that B-cells from patients tolerant to the graft maintained higher IL-10 production after CD40 ligation, which correlates with lower CD86 expression compared to patients with chronic rejection. Hence, the results obtained in this study shed light on a new alternative mechanism by which transitional B-cells inhibit T-cell proliferation and cytokine production. PMID:26795594

Diagnostic value of CD10 and Bcl2 expression in distinguishing cutaneous basal cell carcinoma from squamous cell carcinoma and seborrheic keratosis.

Science.gov (United States)

Gaballah, Mohammad A; Ahmed, Rehab-Allah

2015-12-01

The distinction between cutaneous basal cell carcinoma (BCC), squamous cell carcinoma (SCC) and seborrheic keratosis (SK), which are common entities in clinical practice, can be difficult clinically and histologically. CD10 and Bcl2 antigens are important factors in tumor growth, survival and spread. The aim of the present study is to define the frequency of CD10 and Bcl2 expression in such cutaneous tumors and its relation to the clinicopathological characteristics as well as their possible diagnostic utility. CD10 and Bcl2 immunohistochemistry was performed on 30 BCC, 20 SCC and 15 SK. 93.3% of SK cases and 53.3% of BCC cases showed significant expression of CD10 in tumor cells when compared either with each other or with SCC cases (100% negative). Stromal CD10 expression was positive in 50% of BCC cases and 75% of SCC cases. Stromal CD10 expression was significantly higher in high risk BCC and BCC with infiltrating deep margins; furthermore, it showed a significant positive correlation with grade of SCC. A significant inverse correlation between CD10 expression in stromal and tumor cells of BCC was present. Bcl2 was significantly expressed in 93.3% of SK cases and 80% of BCC cases when compared with SCC cases (100% negative). It was found that for distinguishing BCC from SK, only CD10 expression in tumor cells provided a high diagnostic value with positive likelihood ratio (PLR) was 7.00. In addition, CD10 and Bcl2 expression in tumor cells could give convincing diagnostic value to distinguish SCC from SK (PLR=15.00 for each marker). Moreover, for differentiating BCC from SCC, only Bcl2 in the tumor cells could provide a high diagnostic value (PLR=5.5). In conclusion, CD10 and Bcl2 can help in differentiating cutaneous BCC from SK and SCC. The overexpression of CD10 in the stromal cells of SCC and some variants of BCC suggests the invasive properties of such tumors. Copyright © 2015 Elsevier GmbH. All rights reserved.

Vibrational assignments for the Raman and the phosphorescence spectra of 9,10-anthraquinone and 9,10-anthraquinone-d81

International Nuclear Information System (INIS)

Lehmann, K.K.; Smolarek, J.; Khalil, O.S.; Goodman, L.

1979-01-01

The Raman spectra of 9,10-anthraquinone (AQ) and 9,10-anthraquinone-d/sub 8/ are examined. Raman band assignments are made from this data and from a published normal coordinate analysis. The Raman spectra of AQ at 5K is reported and vibrational assignments for the phosphorescence spectra of AQ in n-hexane at 4.2 K are reexamined in light of new 3 B 1 /sub g/ → 1 A/sub g/ phosphorescence data. Contrary to previous work from this laboratory, it is concluded that although higher order vibronic interactions may be operative between the two closely spaced 3 A/sub u/- 3 B 1 /sub g/ electronic states, these interactions are not manifested in the phosphorescence spectra of AQ in n-hexane at 4.2 K

Zn-10.2% Fe coating over carbon steel atmospheric corrosion resistance. Comparison with zinc coating

International Nuclear Information System (INIS)

Arnau, G.; Gimenez, E.; Rubio, M.V.; Saura, J.J.; Suay, J.J.

1998-01-01

Zn-10.2% Fe galvanized coating versus hot galvanized coating over carbon steel corrosion performance has been studied. Different periods of atmospheric exposures in various Valencia Community sites, and salt spray accelerated test have been done. Carbon steel test samples have been used simultaneously in order to classify exposure atmosphere corrosivity, and environmental exposure atmosphere characteristics have been analyzed. Corrosion Velocity versus environmental parameters has been obtained. (Author) 17 refs

Conversion of MX Nitrides to Modified Z-Phase in 9-12%Cr Ferritic Steels

DEFF Research Database (Denmark)

Cipolla, Leonardo

for Z-phase formation was highlighted during the studies. Several 9-12%Cr commercial steels with prolonged high-temperature exposures have been investigated, too. The same mechanism of Z-phase formation observed in 12%Cr model alloys was identified in industrial 9-12%Cr steels after thousands of hours......The 9-12%Cr ferritic steels are extensively used in modern steam power plants at service temperature up to 620°C. Currently the best perform ing ferritic creep resistance steel is the ASTM Grade 92, whose high temperature strength has recently been assessed by European Creep Collaborative Committee...... in 2005 as 600°C/113MPa/10 5h. All previous attempts made in the last twenty years to develop ferritic steels for 650°C applications have failed due to the incapacity to combine the superior oxidation resistance, given by 12%Cr content, with excellent creep resistance of high-alloyed ferritic steels...

Hydrogenation of 2-ethyl-9,10-anthraquinone on Pd-polyaniline(SiO.sub.2./sub.) composite catalyst. The effect of humidity

Czech Academy of Sciences Publication Activity Database

Drelinkiewicz, A.; Waksmundzka-Góra, A.; Sobczak, J.; Stejskal, Jaroslav

2007-01-01

Roč. 333, č. 2 (2007), s. 219-228 ISSN 0926-860X Institutional research plan: CEZ:AV0Z40500505 Keywords : 2-ethyl-9,10- anthraquinone * polyaniline * palladium catalysts Subject RIV: CD - Macromolecular Chemistry Impact factor: 3.166, year: 2007

Influence of local microplastic strains on stress corrosion of 08Kh18N10T steel

International Nuclear Information System (INIS)

Moskvin, L.N.; Efimov, A.A.; Sherman, Ya.I.; Fedorova, T.I.

1987-01-01

Study on specific features of microhomogeneous strain in the process of plastic strain development and their role in stress corrosion of 08Kh18N10T steel sheet specimens subject to preliminary strain by 1, 3, 6, 16 and 23% and subsequent tests of stress corrosion in magnesium chloride solution at 150 deg C 140 MPa has been carried out. Analysis of test results has shown that microplastic strain is distributed over a specimen nonuniformly and is accompanied with the slip bands formation which are sources of corrosion crack origination and development. 08Kh18N10T steel manifests the highest trend to stress corrosion under 1% microplastic strain

Dielectric relaxation and AC conductivity studies of Se90Cd10−xInx glassy alloys

Directory of Open Access Journals (Sweden)

Nitesh Shukla

2016-06-01

Full Text Available Chalcogenide glassy alloys of Se90Cd10−xInx (x = 2, 4, 6, 8 are synthesized by melt quench technique. The prepared glassy alloys have been characterized by techniques such as differential scanning calorimetry (DSC, scanning electron microscopy (SEM and energy dispersive X-ray (EDAX. Dielectric properties of Se90Cd10−xInx (x = 2, 4, 6, 8 chalcogenide glassy system have been studied using impedance spectroscopic technique in the frequency range 42 Hz to 5 MHz at room temperature. It is found that the dielectric constants ɛ′, dielectric loss factor ɛ″ and loss angle Tan δ depend on frequency. ɛ′, ɛ″ and loss angle Tan δ are found to be decreasing with the In content in Se90Cd10−xInx glassy system. AC conductivity of the prepared sample has also been studied. It is found that AC conductivity increases with frequency where as it has decreasing trend with increasing In content in Se–Cd matrix. The semicircles observed in the Cole–Cole plots indicate a single relaxation process.

12 CFR 9.10 - Fiduciary funds awaiting investment or distribution.

Science.gov (United States)

2010-01-01

... distribution. 9.10 Section 9.10 Banks and Banking COMPTROLLER OF THE CURRENCY, DEPARTMENT OF THE TREASURY... has investment discretion, the bank shall obtain for funds awaiting investment or distribution a rate... principal and interest; (ii) Securities that qualify as eligible for investment by national banks pursuant...

Changes in mechanical properties and structure of electrolytic plasma treated X 12 CrNi 18 10 Ti stainless steel

Energy Technology Data Exchange (ETDEWEB)

Kurbanbekov, Sherzod; Baklanov, Viktor; Karakozov, Batyrzhan [Republican State Enterprise National Nuclear Center of Kazakhstan, Kurchatov (Kazakhstan). Inst. of Atomic Energy Branch; Skakov, Mazhyn [Republican State Enterprise National Nuclear Center of Kazakhstan, Kurchatov (Kazakhstan)

2017-05-01

The paper addresses findings regarding the influence of electrolytic plasma treatment on the mechanical properties as well as structural and phase states of X 12 CrNi 18 10 Ti steel. Electrolytic plasma treatment is based on carburizing of stainless steel heated in electrolytes. Treatment of steel samples has been performed as follows: the samples were heated up to a temperature between 850 and 950 C and then they were cured for 7 minutes in an electrolyte of an aqueous solution containing 10 % glycerol (C{sub 3}H{sub 8}O{sub 3}) and 15 % sodium carbonate (Na{sub 2}CO{sub 3}). It is found that, after plasma electrolytic treatment, the surface of X 12 CrNi 18 10 Ti steel had a modified structure and high hardness. Increasing wear resistance of X 12 CrNi 18 10 Ti steel has been observed after carburizing and the coefficient of friction has been reduced. X-ray analysis showed that retained austenite γ-Fe is a main phase, and there are some diffraction lines of orthorhombic Fe{sub 3}C phase as well as Fe{sub 3}O{sub 4} cubic phase. It has been determined, that, after plasma electrolytic treatment, a carbide phase in the modified surface layer, irrespective of the location in the steel structure has the chemical composition Fe{sub 3}C. High concentration of carbon atoms in a solid solution based on γ- and α-iron, a large dislocation density, presence of particles of carbide phase and retained austenite layers have been found.

Elevated Plasma Soluble CD14 and Skewed CD16+ Monocyte Distribution Persist despite Normalisation of Soluble CD163 and CXCL10 by Effective HIV Therapy: A Changing Paradigm for Routine HIV Laboratory Monitoring?

Science.gov (United States)

Castley, Alison; Berry, Cassandra; French, Martyn; Fernandez, Sonia; Krueger, Romano; Nolan, David

2014-01-01

Objective We investigated plasma and flow cytometric biomarkers of monocyte status that have been associated with prognostic utility in HIV infection and other chronic inflammatory diseases, comparing 81 HIV+ individuals with a range of treatment outcomes to a group of 21 healthy control blood donors. Our aim is to develop and optimise monocyte assays that combine biological relevance, clinical utility, and ease of adoption into routine HIV laboratory practice. Design Cross-sectional evaluation of concurrent plasma and whole blood samples. Methods A flow cytometry protocol was developed comprising single-tube CD45, CD14, CD16, CD64, CD163, CD143 analysis with appropriately matched isotype controls. Plasma levels of soluble CD14 (sCD14), soluble CD163 (sCD163) and CXCL10 were measured by ELISA. Results HIV status was associated with significantly increased expression of CD64, CD143 and CD163 on CD16+ monocytes, irrespective of the virological response to HIV therapy. Plasma levels of sCD14, sCD163 and CXCL10 were also significantly elevated in association with viremic HIV infection. Plasma sCD163 and CXCL10 levels were restored to healthy control levels by effective antiretroviral therapy while sCD14 levels remained elevated despite virological suppression (p<0.001). Conclusions Flow cytometric and plasma biomarkers of monocyte activation indicate an ongoing systemic inflammatory response to HIV infection, characterised by persistent alterations of CD16+ monocyte expression profiles and elevated sCD14 levels, that are not corrected by antiretroviral therapy and likely to be prognostically significant. In contrast, sCD163 and CXCL10 levels declined on antiretroviral therapy, suggesting multiple activation pathways revealed by these biomarkers. Incorporation of these assays into routine clinical care is feasible and warrants further consideration, particularly in light of emerging therapeutic strategies that specifically target innate immune activation in HIV

Elevated plasma soluble CD14 and skewed CD16+ monocyte distribution persist despite normalisation of soluble CD163 and CXCL10 by effective HIV therapy: a changing paradigm for routine HIV laboratory monitoring?

Directory of Open Access Journals (Sweden)

Alison Castley

Full Text Available OBJECTIVE: We investigated plasma and flow cytometric biomarkers of monocyte status that have been associated with prognostic utility in HIV infection and other chronic inflammatory diseases, comparing 81 HIV+ individuals with a range of treatment outcomes to a group of 21 healthy control blood donors. Our aim is to develop and optimise monocyte assays that combine biological relevance, clinical utility, and ease of adoption into routine HIV laboratory practice. DESIGN: Cross-sectional evaluation of concurrent plasma and whole blood samples. METHODS: A flow cytometry protocol was developed comprising single-tube CD45, CD14, CD16, CD64, CD163, CD143 analysis with appropriately matched isotype controls. Plasma levels of soluble CD14 (sCD14, soluble CD163 (sCD163 and CXCL10 were measured by ELISA. RESULTS: HIV status was associated with significantly increased expression of CD64, CD143 and CD163 on CD16+ monocytes, irrespective of the virological response to HIV therapy. Plasma levels of sCD14, sCD163 and CXCL10 were also significantly elevated in association with viremic HIV infection. Plasma sCD163 and CXCL10 levels were restored to healthy control levels by effective antiretroviral therapy while sCD14 levels remained elevated despite virological suppression (p<0.001. CONCLUSIONS: Flow cytometric and plasma biomarkers of monocyte activation indicate an ongoing systemic inflammatory response to HIV infection, characterised by persistent alterations of CD16+ monocyte expression profiles and elevated sCD14 levels, that are not corrected by antiretroviral therapy and likely to be prognostically significant. In contrast, sCD163 and CXCL10 levels declined on antiretroviral therapy, suggesting multiple activation pathways revealed by these biomarkers. Incorporation of these assays into routine clinical care is feasible and warrants further consideration, particularly in light of emerging therapeutic strategies that specifically target innate immune

Comparison of immunohistochemical expression of CD10 in keratocystic odontogenic tumor and ameloblastoma

Directory of Open Access Journals (Sweden)

Elham Hormozi

2016-01-01

Conclusion: The results of this study propose that high expression rate of CD10 might be one of the reasons for the aggressive behavior of AB and high recurrence rate of OKC and reinforce the classification of OKC as an odontogenic tumor.

9-(Guanidinomethyl)-10-vinylanthracene: a suitable fluorescent monomer for MIPs

NARCIS (Netherlands)

Zhang, Huiqi; Verboom, Willem; Reinhoudt, David

2001-01-01

9-(Guanidinomethyl)anthracene derivatives with a bromo (6) or a vinyl group (10) at the 10-position have been prepared starting from 9-bromoanthracene (1). They show 1:1 complexation with carboxylic acids or carboxylates with K-values of 1.2–1.4×105 M−1 in deuteriomethanol. Copolymerization of

Ductile fracture of two-phase welds under 77K. [Steel-EhP810, steel-EhP666, steel-08Kh18N10T, steel-EhP659-VI, steel-chP810

Energy Technology Data Exchange (ETDEWEB)

Yushchenko, K.A.; Voronin, S.A.; Pustovit, A.I.; Shavel' , A.V.

The effect of the type of welding and fillers on crack resistance of welded joints high-strength steel EhP810 and its various compounds with steels EhP666, 08Kh18N10T has been studied. For the welding of steel EhP810 with steels EhP810, EhP666, 08Kh18N10T electron-beam, automatic, argon tungsten arc with non-consumable electrode with various fillers, as well as argon metal-arc welding with consumable electrode, were used. It is shown, that for a joint, made by electron-beam welding, parameters sigmasub(u), Ksub(IcJ), KCV are higher than for a joint of a similar phase structure made using filler wire EhP659-VI. It is explained by the fact, that during electron-beam welding joint metal refining takes place, which removes gases. In welded joints of chP810 steel, having joints with austenitic structure, characteristic of crack resistance Ssub(c) increases by more than 0.2 mm in contrast to two-phase joints, which conventional yield strength at 77 K exceeds 1000 MPa. It is worth mentioning, that for other classes of steels formation of two-phase structure of joint increases welded joint resistance to brittle fracture. It is possible to obtain the required structure of joint with assigned level of resistance to brittle fracture by means of the use of different fillers, optimum and welding procedure, regulating the part of the basic metal in joint content.

Reliability and validity of the Khmer version of the 10-item Connor-Davidson Resilience Scale (Kh-CD-RISC10) in Cambodian adolescents.

Science.gov (United States)

Duong, Chanmettachampavieng; Hurst, Cameron P

2016-06-08

Resilience has been characterized as a defensive factor against the refinement of mental health problems. This study adapted the Connor-Davidson Resilience Scale (Kh-CD-RISC10) for use in Khmer adolescents and subsequently investigates its psychometric properties. Using stratified random sampling, this cross-sectional study sampled Cambodian adolescents from high schools selected randomly within three provinces (Phnom Penh, Battambang and Mondulkiri)-location (rural, urban) combinations. Parallel analysis was used to identify the number of component(s), and the structure of the single factor was subsequently explored using principal axis factoring. A confirmatory factor analysis was then performed to establish the fit of the Kh-CD-RISC10 to another sample. To assess convergent validity, the factor scores of the Khmer version of Connor-Davidson Resilience Scale were categorized into three levels, and then the general negative affectivity (GNA) and physiological hyperarousal (PH) scales (derived from the DASS 21) were compared among the three resilience groups. Of the 798 participants who responded (responded rate = 82.26 %), 440 (41.23 %) were female and the age ranged from 14 to 24 years old (mean = 17.36, SD = 1.325). The internal consistency of the Khmer 10-item CD-RISC was also shown to be high in Cambodian adolescents (Cronbach's alpha = 0. 82). Confirmatory factor analysis revealed the single factor model fit data adequately (χ(2) = 100.103, df = 35, p scale of this population, and can be used to assess the resilience comparing to the level of PTSD symptoms in general Khmer adolescent.

Creep behaviour of the alloys NiCr22Co12Mo and 10CrMo9 10 under static and cyclic load conditions

International Nuclear Information System (INIS)

Wolf, H.

1990-01-01

The creep behaviour of NiCr20Co12Mo is investigated under static strain and at 800deg C, with stresses applied ranging from 105 MPa to 370 MPa. The ferritic steel 10CrMo 9 10 is tested for its creep behaviour under static strain and at the temperatures of 600deg C and 550deg C, with stresses applied between 154 MPa and 326 MPa (at 600deg C), or between 250 MPa and 458 MPa (at 550deg C). The experiments are made to determine the effects of changes in strain on the materials' deformation behaviour, placing emphasis on transient creep and elastic or anelastic response. The mean internal stress is determined from changes in strain. Cyclic creep is analysed as a behaviour directly responding to the pattern of change in strain. Effects of certain strain changes not clarified so far are analysed. The cyclic strain experiments are analysed according to the velocity factor concept. The usual models of creep deformation (theta projection concept) are compared with the model of effective strain, which is based on the fundamental equation of plastic deformation by dislocation motion (Orowan equation). (MM) [de

10 CFR 960.5-2-9 - Rock characteristics.

Science.gov (United States)

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Rock characteristics. 960.5-2-9 Section 960.5-2-9 Energy... Rock characteristics. (a) Qualifying condition. The site shall be located such that (1) the thickness and lateral extent and the characteristics and composition of the host rock will be suitable for...

Effects of Mn addition on microstructures and mechanical properties of 10Cr ODS ferritic/martensitic steels

International Nuclear Information System (INIS)

Jin, Hyun Ju; Kim, Tae Kyu

2014-01-01

Ferritic/martensitic (FM) steels are very attractive for the structural materials of fast fission reactors such as a sodium cooled fast reactor (SFR) owing to their excellent irradiation resistance to a void swelling, but are known to reveal an abrupt loss of their creep and tensile strengths at temperatures above 600 .deg. C. Accordingly, high temperature strength should be considerably improved for an application of the FM steel to the structural materials of SFR. Oxide dispersion strengthened (ODS) FM steels are considered to be promising candidate materials for high- temperature components operating in severe environments such as nuclear fusion and fission systems due to their excellent high temperature strength and radiation resistance stemming from the addition of extremely thermally stable oxide particles dispersed in the ferritic/martensitic matrix.. To develop an advanced ODS steel for core structural materials for next generation nuclear reactor system applications, it is important to optimize its compositions to improve the high temperature strength and radiation resistance. This study investigates effects of Mn addition on microstructures and mechanical properties of 10Cr ODS FM steel. For this, two 10 Cr ODS FM steels were prepared by mechanical alloying (MA), hot isostatic pressing (HIP), and hot rolling process. Tensile tests were carried out at room temperature and 700 .deg. C to evaluate the influences of the Mn element on the mechanical properties. The microstructures were observed using SEM, electron back-scatter diffraction (EBSD) and transmission electron microscopy (TEM) with energy dispersive spectroscopy (EDS). In the present study, the effects of Mn addition on the microstructure and mechanical properties of ODS FM steels were investigated. The ODS FM steels were manufactured by the MA, HIP and hot-rolling processes

Creep performance of welded pipe material made of 7CrMoVTiB10-10 (T/P24) steel

Energy Technology Data Exchange (ETDEWEB)

Rantala, Juhani; Auerkari, Pertti; Salonen, Jorma; Holmstroem, Stefan; Nevasmaa, Pekka [VTT Technical Research Centre of Finland, Espoo (Finland); Haekkilae, Juha [Foster Wheeler Energia, Varkaus (Finland)

2010-07-01

The creep strength of welded low-alloy ferritic steels is typically somewhat lower than that for parent metal, but this is generally due to an inherent weakness of the heat affected zone and accounted for in the common design codes. However, the parent material strength is much higher in certain modern low alloy steels such as 7CrMoVTiB10-10 (P24), and then it can be a significant challenge to develop weld metals (welding consumables) to match this strength. Acceptable weld performance has been previously demonstrated for thin-wall tubes where sufficient mixing with the base material can occur. The objective of this work was to achieve satisfactory properties for a thick-wall welded pipe by using an Nb-modified consumable to avoid weld metal weakening due to arc losses of Ti of a consumable composition approximately matching the base material. A considerable improvement was indeed noted in comparison with earlier experience using matching electrode composition. All short term test results for weld qualification showed acceptable properties, the cross-weld creep strength remain very close to the -20% band from the parent metal creep strength. However, creep testing at lowest stress levels approaching those expected in service resulted in weld metal failure. Although a clear improvement is evident from the previous generation of weld metals, there appears to be some further scope of development of the welding consumables, to improve the long term creep ductility of the welded joints particularly when applying production-like welding parameters. (orig.)

Hydriding of steel in cyanide electrolytes of cadmium plating

International Nuclear Information System (INIS)

Sokol'skaya, N.B.; Maksimchuk, V.P.

1977-01-01

Hydrogenation of steel in cyanide electrolytes for cadmium deposition has been studied in a wide range of compositions. Also investigated have been the scattering capacity and polarization parameters of these electrolytes. The basic components are Cd 2+ and CH - ; besides that, Na 2 SO 4 x10H 2 O, NaOH and NiSO 4 x7H 2 O have been added to the electrolytes. Hydrogenation upon cadmium electrolytic deposition has been determined by the rate of hydrogen penetration through a steel membrane 0.5 mm thick. At the NaCN/Cd(CN) 2 ratio more than 2 the increase in sodium cyanide concentration in the electrolyte appreciably increases neither its hydrogenating and scattering capacity, nor cathodic polarization. The greatest scattering capacity and the highest hydrogenation is exhibited by diluted cadmium deposition elecctrolytes (CdO concentration 9-12 g/1), which prove particularly effective for deposition of regular coatings on complex shape articles. Cadmium deposition on high strength steels, however, should rather involve cyanide electrolytes with high cadmium concentration (50-60 g/1) in order to reduce hydrogenation

Development of plastic deformations in 12Kh18N10T steel under cyclic symmetrical bending of specimens of various length

Energy Technology Data Exchange (ETDEWEB)

Pisarenko, G.S.; Leonets, V.A.; Bega, N.D. (AN Ukrainskoj SSR, Kiev. Inst. Problem Prochnosti)

1983-08-01

Effect of specimen length on intensity of plastic deformation development and cyclic strength is studied for annealed 12Kh18N10T steel under cyclic symmetrical bending. The intensity of microplastic deformations and cyclic strength of annealed 12Kh18N10T steel in the considered case is due to self-heating.

Chronic lymphocytic leukemia cells acquire regulatory B-cell properties in response to TLR9 and CD40 activation.

Science.gov (United States)

Ringelstein-Harlev, Shimrit; Avivi, Irit; Fanadka, Mona; Horowitz, Netanel A; Katz, Tami

2018-02-15

Circulating chronic lymphocytic leukemia (CLL) cells share phenotypic features with certain subsets of regulatory B-cells (Bregs). The latter cells have been reported to negatively regulate immune cell responses, mostly by provision of IL-10. The purpose of the current study was to identify and delineate Breg properties of CLL cells. B-cells and T-cells were obtained from the peripheral blood of untreated CLL patients diagnosed according to the 2008 Guidelines of the International Workshop on Chronic Lymphocytic Leukemia. Co-culture assays were used to examine the ability of CLL cells to suppress autologous T-cell immune responses. IL-10 potency of CLL cells was assessed following stimulation with activators of the toll-like receptor 9 (TLR9) or CD40 and was correlated with the inhibitory activity of the cells. TLR9-activated CLL cells were found to increase the frequency of CD4 + CD25 hi FOXp3 + regulatory T-cells (Tregs) and to inhibit autologous CD4 + T-cell proliferation. This signaling cascade proved to control IL-10 generation in CLL cells, which in turn promoted the inhibition of T-cell proliferation by CLL cells. However, CD40 activation of CLL cells, while exhibiting a similar ability to augment Treg frequency, did not either affect IL-10 generation or T-cell proliferation. In conclusion, CLL cells demonstrate a unique clonal quality of adopting Breg properties which promote modulation of T-cell characteristics. TLR9 appears to be a potent activator of regulatory abilities in CLL cells, possibly contributing to preferential immune escape of TLR9-responsive cells.

1,25-dihydroxyvitamin D3 and dexamethasone increase interleukin-10 production in CD4+ T cells from patients with Crohn's disease

DEFF Research Database (Denmark)

Bartels, Lars Erik; Jørgensen, Søren Peter; Agnholt, Jørgen

2007-01-01

,25-dihydroxyvitamin D3 with and without DEX could induce IL-10 production, downregulate pro-inflammatory Interferon (IFN)-gamma and Tumor Necrosis Factor (TNF)-alpha production, and influence cell kinetics in peripheral CD4+ T cells from CD patients. METHODS: CD4+ T cells were separated from peripheral blood from CD......BACKGROUND AND AIM: In Crohn's disease (CD), epidemiological data and animal studies suggest that vitamin D (vitD) has protective immune-modulating properties. 1,25-dihydroxyvitamin D3 and dexamethasone (DEX) induce interleukin (IL)-10 productions in healthy controls (HC) T cells. We studied if 1...... patients and HC. Cells were activated by anti-CD3 and anti-CD28 in the presence of 1,25-dihydroxyvitamin D3 and/or DEX. Cytokine levels, proliferation, and apoptosis were measured following 7 days of culture. RESULTS: In T cells from CD patients, 1,25-dihydroxyvitamin D3 and DEX increased IL-10 production...

Influence of cold work on the diffusion of ion-implanted nitrogen in D9 steel using nuclear reaction analysis

International Nuclear Information System (INIS)

Arunkumar, J.; David, C.; Panigrahi, B.K.; Nair, K.G.M.

2014-01-01

D9 steels and their modified versions are envisaged for use as fuel cladding and wrapper materials in the Indian fast breeder reactor (FBR) programme. The role played by interstitially dissolved nitrogen in steel matrices for the stabilization of austenitic phase, increase of strength and corrosion resistance is well known. Various factors: the role of grain boundaries and the their orientation, stress mediation, grain fragmentation and production of short circuit paths as a result of compressive stress are known to affect the diffusion of nitrogen. Basically, cold working produces plethora of defects throughout the sample as compared to its solution annealed state. Our earlier studies on 1 x10"1"5 and 5x10"1"5 N"1"5 implanted Solution Annealed D9 (SAD9) showed significant vacancy-nitrogen complexes for higher fluence. Hence, thermal diffusion behaviour of nitrogen was studied in 5 x10"1"5 -N"1"5 implanted samples in solution annealed state. In the present study, to understand the influence of cold work, similar thermal diffusion behaviour of nitrogen has been studied in Cold Worked D9 steel (CWD9) using nuclear reaction analysis

75 FR 47199 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-9-10 Series Airplanes, DC-9-30...

Science.gov (United States)

2010-08-05

... Airworthiness Directives; McDonnell Douglas Corporation Model DC- 9-10 Series Airplanes, DC-9-30 Series... existing airworthiness directive (AD), which applies to all McDonnell Douglas Model DC-9-10 series..., 2010). That AD applies to all McDonnell Douglas Corporation Model DC-9-10 series airplanes, DC-9-30...

High Levels of IL-10 and CD4+CD25hi+ Treg Cells in Endemic Burkitt’s Lymphoma Patients

Directory of Open Access Journals (Sweden)

Godfred Futagbi

2015-08-01

Full Text Available Background: The interplay between Epstein-Barr virus infection, malaria, and endemic Burkitt’s Lymphoma is not well understood. Reports show diminished EBV-specific Th1 responses in children living in malaria endemic areas and deficiency of EBNA1-specific IFN-γ T cell responses in children with endemic Burkitt’s Lymphoma (eBL. This study, therefore, examined some factors involved in the loss of EBNA-1-specific T cell responses in eBL. Methods: T-cell subset frequencies, activation, and IFN-γ- or IL-4-specific responses were analyzed by flow-cytometry. Plasma cytokine levels were measured by ELISA. Results: CD4+ and CD8+ cells in age- and sex-matched healthy controls (n = 3 expressed more IFN-γ in response to all immunostimulants than in pediatric endemic BL (eBL patients (n = 4. In healthy controls, IFN-γ expression was higher than IL-4 expression, whereas in eBL patients the expression of IL-4 by CD4+ cells to EBNA-1 was slightly higher than IFN-γ. Moreover, the blood levels of TNF-α was significantly lower (p = 0.004 while IL-10 was significantly higher (p = 0.038, in eBL patients (n = 21 compared to controls (n = 16. Additionally, the frequency of CD4+CD25hi+ T cells was higher in both age-matched acute uncomplicated malaria (n = 26 and eBL (n = 14 patients compared to healthy controls (n = 19; p = 0.000 and p = 0.027, respectively. Conclusion: The data suggest that reduced Th1 response in eBL might be due to increased levels of IL-10 and T reg cells.

High Levels of IL-10 and CD4+CD25hi+ Treg Cells in Endemic Burkitt’s Lymphoma Patients

Science.gov (United States)

Futagbi, Godfred; Gyan, Ben; Nunoo, Harriet; Tetteh, John K.A.; Welbeck, Jennifer E.; Renner, Lorna Awo; Ofori, Michael; Dodoo, Daniel; Edoh, Dominic A.; Akanmori, Bartholomew D.

2015-01-01

Background: The interplay between Epstein-Barr virus infection, malaria, and endemic Burkitt’s Lymphoma is not well understood. Reports show diminished EBV-specific Th1 responses in children living in malaria endemic areas and deficiency of EBNA1-specific IFN-γ T cell responses in children with endemic Burkitt’s Lymphoma (eBL). This study, therefore, examined some factors involved in the loss of EBNA-1-specific T cell responses in eBL. Methods: T-cell subset frequencies, activation, and IFN-γ- or IL-4-specific responses were analyzed by flow-cytometry. Plasma cytokine levels were measured by ELISA. Results: CD4+ and CD8+ cells in age- and sex-matched healthy controls (n = 3) expressed more IFN-γ in response to all immunostimulants than in pediatric endemic BL (eBL) patients (n = 4). In healthy controls, IFN-γ expression was higher than IL-4 expression, whereas in eBL patients the expression of IL-4 by CD4+ cells to EBNA-1 was slightly higher than IFN-γ. Moreover, the blood levels of TNF-α was significantly lower (p = 0.004) while IL-10 was significantly higher (p = 0.038), in eBL patients (n = 21) compared to controls (n = 16). Additionally, the frequency of CD4+CD25hi+ T cells was higher in both age-matched acute uncomplicated malaria (n = 26) and eBL (n = 14) patients compared to healthy controls (n = 19; p = 0.000 and p = 0.027, respectively). Conclusion: The data suggest that reduced Th1 response in eBL might be due to increased levels of IL-10 and T reg cells. PMID:28536409

n Vitro Immunomodulatory Effect of R10 Fraction of Garlic on Viability and Production of TNF-? in CD8+ T Cells

Directory of Open Access Journals (Sweden)

T. Ghazanfari

2014-01-01

Full Text Available Introduction & Objective: -cells, especially CD8+ T lymphocytes are the most important cells in anti-tumor response. Previously R10 fraction of garlic extract was reported as an immuno-modulator which induced an effective cellular immunity and Th1 responses. In this study the in vitro immunomodulatory effect of R10 on CD8+ T cells viability and production of TNF-? were evaluated. Materials & Methods: In this experimental study, using monoclonal antibodies attached to magnetic beads with isolating columns by magnetic bead method, CD8+ T cells from spleen cells of Balb/C mice were isolated. R10 fraction based on molecular weight was prepared using Ultra filtration. MTT assay was used to evaluate cell viability. TNF-? level was meas-ured in the supernatant of culture of CD8+ T cells by ELISA. Obtained data was compared and analyzed using Nonparametric Test and Keraskel & Wanny's Test tests.. Results: The findings indicate that all dilutions of R10 fraction increased cell viability of CD8+ T cells in comparison with the negative control group and in the presence of ConA with dilution of 1:50 of R10 fraction significantly increased cell viability of CD8+ T Cells com-pared to ConA alone. Secretion of TNF-? significantly increased by all dilutions of R10 frac-tion. Conclusion: These findings suggest that R10 fraction of garlic can be used as an Immuno-modulator drug candidate for induction of cellular Immunity in tumor therapy. Sci J Hamadan Univ Med Sci 2014; 20 (4:273-279

9,10-Dioxoanthracene-1,4-diyl bis(4-methylbenzenesulfonate

Directory of Open Access Journals (Sweden)

Sirirat Kokpol

2012-05-01

Full Text Available The title molecule, C28H20O8S2, has a T-shaped conformation. The central 9,10-anthraquinone moiety is bow-shaped with the two outer aromatic rings being inclined to one another by 13.99 (11°. The benzenesulfonate rings are inclined to one another by 47.35 (12°, and by 34.51 (11 and 17.88 (11° to the bridging aromatic ring of the 9,10-anthraquinone moiety. In the crystal, C—H...O interactions link the molecules into ribbons in [100].

Generation of 320 mW at 10.20 μm based on CdSe long-wave infrared crystal

Science.gov (United States)

Wang, Jian; Yuan, Ligang; Zhang, Yingwu; Chen, Guo; Cheng, Hongjuan; Gao, Yanzhao

2018-06-01

CdSe single crystal, with the sizes of ∼54 mm in diameter and ∼25 mm in length, was grown by a high pressure vertical gradient freeze (HPVGF) technique using (0 0 1)-oriented seed. The CdSe crystal was characterized with transmission spectrophotometer. The transmission spectra showed that the infrared transmission was above 68% and the mean absorption coefficient was 0.041 cm-1 in the range of 2.5-20 μm. Using fabricated CdSe crystal with the dimensions of 6 mm × 10 mm × 44 mm, we demonstrated an optical parametric oscillator (OPO) pumped by a 2.05 μm Ho:YLF laser at a pulse repetition frequency of 5 kHz. Up to 320 mW output was obtained at the idler wavelength of 10.20 μm with a pump power of 18.06 W. 320 mW at 10.20 μm, to our knowledge, was the highest power obtained with a 2.05 μm laser-pumped CdSe OPO.

Sandwich iridium complexes with the monoanionic carborane ligand [9-SMe2-7,8-C2B9H10]-

International Nuclear Information System (INIS)

Loginov, D.A.; Vinogradov, M.M.; Perekalin, D.S.; Starikova, Z.A.; Lysenko, K.A.; Petrovskij, P.V.; Kudinov, A.R.

2006-01-01

The reaction of the [(η-9-SMe 2 -7,8-C 2 B 9 H 10 )IrBr 2 ] 2 complex with Tl[Tl(η-7,8-C 2 B 9 H 11 )] afforded the iridacarborane compound (η-9-SMe 2 -7,8-C 2 B 9 H 10 )Ir(η-7,8-C 2 B 9 H 11 ). The cationic complex [Cp*Ir(η-9-SMe 2 -7,8-C 2 B 9 H 10 )] + PF 6 - (Cp* is pentamethylcyclopentadienyl) was synthesized by the reaction of [Cp*IrCl 2 ] 2 with Na[9-SMe 2 -7,8-C 2 B 9 H 10 ]. The structures of (η-9-SMe 2 -7,8-C 2 B 9 H 10 )Ir(η-cod) (cod is 1,5-cyclooctadiene) and [Cp*Ir(η-9-SMe 2 -7,8-C 2 B 9 H 10 ]PF 6 were established by X-ray diffraction [ru

9 CFR 130.10 - User fees for pet birds.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false User fees for pet birds. 130.10... AGRICULTURE USER FEES USER FEES § 130.10 User fees for pet birds. (a) User fees for pet birds of U.S. origin returning to the United States, except pet birds of U.S. origin returning from Canada, are as follows...

Diels-Alder Reactions of 12-Hydroxy-9(10®20-5aH-abeo-abieta-1(10,8(9,12(13-triene-11,14-dione

Directory of Open Access Journals (Sweden)

Shougang Hu

2013-06-01

Full Text Available 12-Hydroxy-9(10®20-5aH-abeo-abieta-1(10,8(9,12(13-triene-11,14-dione (quinone 2 served as the dienophile in numerous intermolecular Diels-Alder reactions. These cycloadditions were conducted either thermally (including microwave heating or with Lewis acid activation. While most dienes reacted with quinone 2 in good chemical yield, others were incompatible under the experimental conditions used.

IFN-γ-producing NKT cells exacerbate sepsis by enhancing C5a generation via IL-10-mediated inhibition of CD55 expression on neutrophils.

Science.gov (United States)

Kim, Ji Hyung; Oh, Sae Jin; Ahn, Sehee; Chung, Doo Hyun

2014-07-01

A role for NKT cells has been implicated in sepsis, but the mechanism by which NKT cells contribute to sepsis remains unclear. Here, we examined WT and NKT-cell-deficient mice of C57BL/6 background during cecal ligation and puncture-induced sepsis. The levels of C5a, IFN-γ, and IL-10 were higher in the serum and peritoneal fluid of WT mice than in those of CD1d(-/-) mice, while the mortality rate was lower in CD1d(-/-) mice than in WT mice. C5a blockade decreased mortality of WT mice during sepsis, whereas it did not alter that of CD1d(-/-) mice. As assessed by intracellular staining, NKT cells expressed IFN-γ, while neutrophils expressed IL-10. Upon coculture, IL-10-deficient NKT cells enhanced IL-10 production by WT, but not IFN-γR-deficient, neutrophils. Meanwhile, CD1d(-/-) mice exhibited high CD55 expression on neutrophils during sepsis, whereas those cells from WT mice expressed minimal levels of CD55. Recombinant IL-10 administration into CD1d(-/-) mice reduced CD55 expression on neutrophils. Furthermore, adoptive transfer of sorted WT, but not IFN-γ-deficient, NKT cells into CD1d(-/-) mice suppressed CD55 expression on neutrophils, but increased IL-10 and C5a levels. Taken together, IFN-γ-producing NKT cells enhance C5a generation via IL-10-mediated inhibition of CD55 expression on neutrophils, thereby exacerbating sepsis. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

CXCL10/CXCR3-Dependent Mobilization of Herpes Simplex Virus-Specific CD8+ TEM and CD8+ TRM Cells within Infected Tissues Allows Efficient Protection against Recurrent Herpesvirus Infection and Disease.

Science.gov (United States)

Srivastava, Ruchi; Khan, Arif A; Chilukuri, Sravya; Syed, Sabrina A; Tran, Tien T; Furness, Julie; Bahraoui, Elmostafa; BenMohamed, Lbachir

2017-07-15

Herpes simplex virus 1 (HSV-1) establishes latency within the sensory neurons of the trigeminal ganglia (TG). HSV-specific memory CD8 + T cells play a critical role in preventing HSV-1 reactivation from TG and subsequent virus shedding in tears that trigger recurrent corneal herpetic disease. The CXC chemokine ligand 10 (CXCL10)/CXC chemokine receptor 3 (CXCR3) chemokine pathway promotes T cell immunity to many viral pathogens, but its importance in CD8 + T cell immunity to recurrent herpes has been poorly elucidated. In this study, we determined how the CXCL10/CXCR3 pathway affects TG- and cornea-resident CD8 + T cell responses to recurrent ocular herpesvirus infection and disease using a well-established murine model in which HSV-1 reactivation was induced from latently infected TG by UV-B light. Following UV-B-induced HSV-1 reactivation, a significant increase in both the number and function of HSV-specific CXCR3 + CD8 + T cells was detected in TG and corneas of protected C57BL/6 (B6) mice, but not in TG and corneas of nonprotected CXCL10 -/- or CXCR3 -/- deficient mice. This increase was associated with a significant reduction in both virus shedding and recurrent corneal herpetic disease. Furthermore, delivery of exogenous CXCL10 chemokine in TG of CXCL10 -/- mice, using the neurotropic adeno-associated virus type 8 (AAV8) vector, boosted the number and function of effector memory CD8 + T cells (T EM ) and tissue-resident memory CD8 + T cells (T RM ), but not of central memory CD8 + T cells (T CM ), locally within TG, and improved protection against recurrent herpesvirus infection and disease in CXCL10 -/- deficient mice. These findings demonstrate that the CXCL10/CXCR3 chemokine pathway is critical in shaping CD8 + T cell immunity, locally within latently infected tissues, which protects against recurrent herpesvirus infection and disease. IMPORTANCE We determined how the CXCL10/CXCR3 pathway affects CD8 + T cell responses to recurrent ocular herpesvirus

PLASTIC DEFORMATION ON THE MACHINED SURFACE OF STEEL Cr20Ni10MoTi AT DRILLING

Directory of Open Access Journals (Sweden)

Jozef Jurko

2009-07-01

Full Text Available Information about material machinability is very important for the machining technology. Precise and reliable information on the machinability of a material before it enters the machining process is a necessity, and this brings the verification of technological methods in practice. This article presents the conclusions of machinability tests on austenitic stainless steel according to EN-EU (ISO: steel Cr20Ni10MoTi. This article presents the conclusions of VEGA grant agency at the Ministry of Education SR for supporting research work and co-financing the projects: Grant work #01/3173/2006 with the title „Experimental investigation of cutting zones in drilled and milled stainless steels

(1S,3S,8R,9S,10R-9,10-Epoxy-3,7,7,10-tetramethyltricyclo[6.4.0.01,3]dodecane

Directory of Open Access Journals (Sweden)

Abdoullah Bimoussa

2014-04-01

Full Text Available The title compound, C16H26O, was synthesized by treating (1S,3S,8R-3,7,7,10-tetramethyltricyclo[6.4.0.01,3]dodec-9-ene with metachloroperbenzoic acid. The molecule is built up from two fused six- and seven-membered rings. The six-membered ring has a half-chair conformation, whereas the seven-membered ring displays a boat conformation. In the crystal, there are no significant intermolecular interactions present.

Protective effect of KhOSP-10 inhibitor during corrosion, hydrogenadsorption and corrosion cracking of a steel in sulfuric acid

Energy Technology Data Exchange (ETDEWEB)

Mindyuk, A K; Svist, E I; Savitskaya, O P; Goyan, E B; Gopanenko, A N [AN Ukrainskoj SSR, Lvov. Fiziko-Mekhanicheskij Inst.

1975-01-01

The protective propeties of inhibitor KhOSP-10 in the time of corrosion and corrosive cracking of steel 40Kh are higher then those of inhibitors KPI-1, KI-1, I-I-V etc. Its ability to reduce steel hydrogenation is the same as in the case of KPI-1 inhibitor i.e. below that of KI-1. HCl additives enhance the efficiency of inhibitors KPI-1, KI-1, I-1-V etc. up to the protective ability of KhOSP-10. Kinetics of the electrode processes was estimated from polarization curves.

Susceptibility to stress corrosion in stainless steels type AISI 321 and 12X18H10T used in PWR type reactors (WWER)

International Nuclear Information System (INIS)

Matadamas C, N.

1995-01-01

Titanium stabilized stainless steels have been utilized in sovietic pressurized water reactors (VVER) for avoid the susceptibility to Intergranular Corrosion (IGC) present in other austenitic stainless steels. However the Intergranular Corrosion resistance of this kind of materials has been questioned because of Intergranular Stress Corrosion Cracking failures (IGSCC) have been reported. This paper study the electrochemical behavior of the AISI 321 stainless steel in a H 3 BO 3 Solution contaminated with chlorides and its susceptibility to Intergranular Corrosion.Electrochemical prediction diagrams of the stainless steels AISI 321 and 12X18H10T (sovietic) sensitized (600 Centigrade, 3 h.) were compared. Cylindrical and conical samples were used in Slow Strain Rate Tests (SSRT), to determine the susceptibility to Stress Corrosion Cracking (SCC) in AISI 321 and 12X18H10T stainless steels. The results obtained showed that the temperature of the solution is a very important factor to detect this susceptibility. Fractography studies on the fracture surfaces of the samples obtained in the SSRT at high temperature were realized. Corrosion velocities of both AISI 321 and 12X18H10T stainless steels were determined using conical samples in the CERT system at high temperature. E.D.A.X. analysis was employed in both AISI 321 and 12X18H10T stainless steels in order to explain the degree of sensitization. (Author)

Validation and Application of Computed Radiography (CR) Tangential Technique for Wall Thickness Measurement of 10 Inch Carbon Steel Pipe

International Nuclear Information System (INIS)

Norhazleena Azaman; Khairul Anuar Mohd Salleh; Amry Amin Abas; Arshad Yassin; Sukhri Ahmad

2016-01-01

Oil and gas industry requires Non Destructive Testing (NDT) to ensure each components, in-service and critical, are fit-for-purpose. Pipes that are used to transfer oil or gas are amongst the critical component that needs to be well maintained and inspected. Typical pipe discontinuities that may lead to unintended incidents are erosion, corrosion, dent, welding defects, etc. Wall thickness assessment, with Radiography Testing (RT) is normally used to inspect such discontinuities and can be performed with two approaches; (a) center line beam tangential technique (b) offset from the centre pipe tangential technique. The latter is a method of choice for this work because of the pipe dimension and limited radiation safe distance at site. Two successful validation approaches (simulation and experimental) were performed to determine the probability of successfulness before the actual RT work with tangential technique is carried out. The pipe was a 10 inch diameter in-service wrapped carbon steel. A 9 Ci Ir-192 and white Imaging Plate (IP) were used as a gamma radiation source and to record the radiographic image. Result of this work suggest that RT with tangential technique for 10 inch wrapped in-service carbon steel pipe can be successfully performed. (author)

The unbound isotopes He-9,He-10

CERN Document Server

Jonson, B; Cortina-Gil, D; Simon, H; Emling, H; Nyman, G; Nilsson, T; Johansson, H T; Borge, M J G; Paschalis, S; Muenzenberg, G; Zhukov, M V; Weick, H; Pramanik, U Datta; LeBleis, T; Meister, M; Reifarth, R; Chulkov, L V; Lantz, M; Riisager, K; Mahata, K; Suemmerer, K; Langer, C; Chatillon, A; Richter, A; Kulessa, R; Palit, R; Aksyutina, Yu; Geissel, H; Aumann, T; Prokopowicz, W; Forssen, C; Ickert, G; Fynbo, H O U; Tengblad, O; Boretzky, K

2010-01-01

The unbound nuclei He-9 and He-10 have been produced in proton-knockout reactions from a 280 MeV/u Li-11 beam impinging on a liquid hydrogen target at the ALADIN-LAND setup at GSI. Information on their nuclear structure has been obtained from the relative-energy spectra, He-8 + n and He-8 + 2n, employing reaction models incorporating the structure of Li-11. The (8H)e + n relative-energy spectrum is dominated by a strong peak-like structure at low energy, which may be interpreted within the effective-range approximation as the result of an s-wave interaction with a neutron scattering length of -3.17(66) fm. This spectrum also shows evidence for resonance states at 1.33(8) MeV and at 2.4 MeV above the He-8 + n threshold. It is argued that the s-state might not be the He-9 ground state. For He-8 + n + n, the analysis of the relative-energy spectrum gives two alternative possibilities for an interpretation: either a narrow resonance at 1.42(10) MeV (Gamma = 1.11(76) MeV) superimposed on a correlated background, o...

BIP induces mice CD19(hi) regulatory B cells producing IL-10 and highly expressing PD-L1, FasL.

Science.gov (United States)

Tang, Youfa; Jiang, Qing; Ou, Yanghui; Zhang, Fan; Qing, Kai; Sun, Yuanli; Lu, Wenjie; Zhu, Huifen; Gong, Feili; Lei, Ping; Shen, Guanxin

2016-01-01

Many studies have shown that B cells possess a regulatory function in mouse models of autoimmune diseases. Regulatory B cells can modulate immune response through many types of molecular mechanisms, including the production of IL-10 and the expression of PD-1 Ligand and Fas Ligand, but the microenvironmental factors and mechanisms that induce regulatory B cells have not been fully identified. BIP (binding immunoglobulin protein), a member of the heat shock protein 70 family, is a type of evolutionarily highly conserved protein. In this article, we have found that IL-10(+), PD-L1(hi) and FasL(hi) B cells are discrete cell populations, but enriched in CD19(hi) cells. BIP can induce IL-10-producing splenic B cells, IL-10 secretion and B cells highly expressing PD-L1 and FasL. CD40 signaling acts in synergy with BIP to induce regulatory B cells. BIP increased surface CD19 molecule expression intensity and IL-10(+), PD-L1(hi) and FasL(hi) B cells induced by BIP share the CD19(hi) phenotype. Furthermore, B cells treated with BIP and anti-CD40 can lead to suppression of T cell proliferation and the effect is partially IL-10-dependent and mainly BIP-induced. Taken together, our findings identify a novel function of BIP in the induction of regulatory B cells and add a new reason for the therapy of autoimmune disorders or other inflammatory conditions. Copyright © 2015. Published by Elsevier Ltd.

CD4+ Primary T Cells Expressing HCV-Core Protein Upregulate Foxp3 and IL-10, Suppressing CD4 and CD8 T Cells

Science.gov (United States)

Aguado, Enrique; Garcia-Cozar, Francisco

2014-01-01

Adaptive T cell responses are critical for controlling HCV infection. While there is clinical evidence of a relevant role for regulatory T cells in chronic HCV-infected patients, based on their increased number and function; mechanisms underlying such a phenomena are still poorly understood. Accumulating evidence suggests that proteins from Hepatitis C virus can suppress host immune responses. We and others have shown that HCV is present in CD4+ lymphocytes from chronically infected patients and that HCV-core protein induces a state of unresponsiveness in the CD4+ tumor cell line Jurkat. Here we show that CD4+ primary T cells lentivirally transduced with HCV-core, not only acquire an anergic phenotype but also inhibit IL-2 production and proliferation of bystander CD4+ or CD8+ T cells in response to anti-CD3 plus anti-CD28 stimulation. Core-transduced CD4+ T cells show a phenotype characterized by an increased basal secretion of the regulatory cytokine IL-10, a decreased IFN-γ production upon stimulation, as well as expression of regulatory T cell markers, CTLA-4, and Foxp3. A significant induction of CD4+CD25+CD127lowPD-1highTIM-3high regulatory T cells with an exhausted phenotype was also observed. Moreover, CCR7 expression decreased in HCV-core expressing CD4+ T cells explaining their sequestration in inflamed tissues such as the infected liver. This work provides a new perspective on de novo generation of regulatory CD4+ T cells in the periphery, induced by the expression of a single viral protein. PMID:24465502

CD4+ primary T cells expressing HCV-core protein upregulate Foxp3 and IL-10, suppressing CD4 and CD8 T cells.

Directory of Open Access Journals (Sweden)

Cecilia Fernandez-Ponce

Full Text Available Adaptive T cell responses are critical for controlling HCV infection. While there is clinical evidence of a relevant role for regulatory T cells in chronic HCV-infected patients, based on their increased number and function; mechanisms underlying such a phenomena are still poorly understood. Accumulating evidence suggests that proteins from Hepatitis C virus can suppress host immune responses. We and others have shown that HCV is present in CD4+ lymphocytes from chronically infected patients and that HCV-core protein induces a state of unresponsiveness in the CD4+ tumor cell line Jurkat. Here we show that CD4+ primary T cells lentivirally transduced with HCV-core, not only acquire an anergic phenotype but also inhibit IL-2 production and proliferation of bystander CD4+ or CD8+ T cells in response to anti-CD3 plus anti-CD28 stimulation. Core-transduced CD4+ T cells show a phenotype characterized by an increased basal secretion of the regulatory cytokine IL-10, a decreased IFN-γ production upon stimulation, as well as expression of regulatory T cell markers, CTLA-4, and Foxp3. A significant induction of CD4+CD25+CD127(lowPD-1(highTIM-3(high regulatory T cells with an exhausted phenotype was also observed. Moreover, CCR7 expression decreased in HCV-core expressing CD4+ T cells explaining their sequestration in inflamed tissues such as the infected liver. This work provides a new perspective on de novo generation of regulatory CD4+ T cells in the periphery, induced by the expression of a single viral protein.

Microstructure refinement and strengthening mechanisms of a 9Cr oxide dispersion strengthened steel by zirconium addition

International Nuclear Information System (INIS)

Xu, Hai Jian; Lu, Zheng; Wang, Dong Mei; Liu, Chunming

2017-01-01

To study the effects of zirconium (Zr) addition on the microstructure, hardness and the tensile properties of oxide dispersion strengthened (ODS) ferritic-martensitic steels, two kinds of 9Cr-ODS ferritic-martensitic steels with nominal compositions (wt.%) of Fe-9Cr-2W-0.3Y_2O-3 and Fe-9Cr-2W-0.3Zr-0.3Y_2O_3 were fabricated by the mechanical alloying (MA) of premixed powders and then consolidated by hot isostatic pressing (HIP) techniques. The experimental results showed that the average grain size decreases with Zr addition. The trigonal δ-phase Y_4Zr_3O_1_2 oxides and body-centered cubic Y_2O_3 oxides are formed in the 9Cr-Zr-ODS steel and 9Cr non-Zr ODS steel, respectively, and the average size of Y_4Zr_3O_1_2 particles is much smaller than that of Y_2O_3. The dispersion morphology of the oxide particles in 9Cr-Zr-ODS steel is significantly improved and the number density is 1.1 x 10"2"3/m"3 with Zr addition. The 9Cr-Zr-ODS steel shows much higher tensile ductility, ultimate tensile strength and Vickers hardness at the same time

Convenient synthesis of 6-nor-9,10-dihydrolysergic acid methyl ester.

Science.gov (United States)

Crider, A M; Grubb, R; Bachmann, K A; Rawat, A K

1981-12-01

6-Nor-9,10-dihydrolysergic acid methyl ester (IV) was prepared by demethylation of 9,10-dihydrolysergic acid methyl ester (II) with 2,2,2-trichloroethyl chloroformate, followed by reduction of the intermediate carbamate (III) with zinc in acetic acid. The 6-ethyl-V and 6-n-propyl-VI derivatives were prepared by alkylation of IV with the appropriate halide. All of the ergoline derivatives were evaluated for stereotyped behavior in rats, with 6-nor-6-ethyl-9,10-dihydrolysergic acid methyl ester (V) being active but much less potent than apomorphine. Compound VI was evaluated for its effect on blood pressure; at a dose of 30 mg/kg ip, it significantly lowered, diastolic pressure in normotensive rats.

Low-Cycle Fatigue Behavior of 10CrNi3MoV High Strength Steel and Its Undermatched Welds.

Science.gov (United States)

Song, Wei; Liu, Xuesong; Berto, Filippo; Razavi, S M J

2018-04-24

The use of high strength steel allows the design of lighter, more slender and simpler structures due to high strength and favorable ductility. Nevertheless, the increase of yield strength does not guarantee the corresponding improvement of fatigue resistance, which becomes a major concern for engineering structure design, especially for the welded joints. The paper presents a comparison of the low cycle fatigue behaviors between 10CrNi3MoV high strength steel and its undermatched weldments. Uniaxial tension tests, Push-pull, strain-controlled fatigue tests were conducted on base metal and weldments in the strain range of 0.2⁻1.2%. The monotonic and cyclic stress-strain curves, stress-life, strain-life and energy-life in terms of these materials were analyzed for fatigue assessment of materials discrepancy. The stress-life results of base metal and undermatched weld metal exhibit cyclic softening behaviors. Furthermore, the shapes of 10CrNi3MoV steel hysteresis loops show a satisfactory Masing-type behavior, while the weld metal shows a non-Masing type behavior. Strain, plastic and total strain energy density amplitudes against the number of reversals to failure results demonstrate that the undermatched weld metal presents a higher resistance to fatigue crack initiation than 10CrNi3MoV high strength steel. Finally, fatigue fracture surfaces of specimens were compared by scanning electron microscopy to identify the differences of crack initiation and the propagation between them.

Low-Cycle Fatigue Behavior of 10CrNi3MoV High Strength Steel and Its Undermatched Welds

Directory of Open Access Journals (Sweden)

Wei Song

2018-04-01

Full Text Available The use of high strength steel allows the design of lighter, more slender and simpler structures due to high strength and favorable ductility. Nevertheless, the increase of yield strength does not guarantee the corresponding improvement of fatigue resistance, which becomes a major concern for engineering structure design, especially for the welded joints. The paper presents a comparison of the low cycle fatigue behaviors between 10CrNi3MoV high strength steel and its undermatched weldments. Uniaxial tension tests, Push-pull, strain-controlled fatigue tests were conducted on base metal and weldments in the strain range of 0.2–1.2%. The monotonic and cyclic stress-strain curves, stress-life, strain-life and energy-life in terms of these materials were analyzed for fatigue assessment of materials discrepancy. The stress-life results of base metal and undermatched weld metal exhibit cyclic softening behaviors. Furthermore, the shapes of 10CrNi3MoV steel hysteresis loops show a satisfactory Masing-type behavior, while the weld metal shows a non-Masing type behavior. Strain, plastic and total strain energy density amplitudes against the number of reversals to failure results demonstrate that the undermatched weld metal presents a higher resistance to fatigue crack initiation than 10CrNi3MoV high strength steel. Finally, fatigue fracture surfaces of specimens were compared by scanning electron microscopy to identify the differences of crack initiation and the propagation between them.

Microstructural stability of fast reactor irradiated 10 to 12% Cr ferritic-martensitic stainless steels

International Nuclear Information System (INIS)

Little, E.A.; Stoter, L.P.

1982-01-01

The strength and microstructural stability of three 10 to 12% Cr ferritic-martensitic stainless steels have been characterized following fast reactor irradiation to damage levels of 30 displacements per atom (dpa) at temperatures in the range 380 to 615 0 C. Irradiation results in either increases or decreases in room temperature hardness depending on the irradiation temperature. These strength changes can be qualitatively rationalized in terms of the combined effects of irradiation-induced interstitial dislocation loop formation and recovery of the dislocation networks comprising the initial tempered martensite structures. Precipitate evolution in the irradiated steels is associated with the nonequilibrium segregation of the elements nickel, silicon, molybdenum, chromium and phosphorus, brought about by solute-point defect interactions. The principal irradiation-induced precipitates identified are M 6 X, intermetallic chi and sigma phases and also α' (Cr-rich ferrite). The implications of the observed microstructural changes on the selection of martensitic stainless steels for fast reactor wrapper applications are briefly considered

10 CFR 1045.9 - RD classification performance evaluation.

Science.gov (United States)

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false RD classification performance evaluation. 1045.9 Section... classification performance evaluation. (a) Heads of agencies shall ensure that RD management officials and those... RD or FRD documents shall have their personnel performance evaluated with respect to classification...

Influence of the fabrication process parameters on microstructures and mechanical properties of 10Cr-1Mo ODS steel

International Nuclear Information System (INIS)

Jin, Hyun Ju; Kim, Ki Baik; Choi, Byoung Kwon; Kang, Suk Hoon; Noh, Sang Hoon; Kim, Ga Eon; Kim, Tae Kyu

2016-01-01

Oxide dispersion strengthened (ODS) FM steels have been developed as the most promising core structural material for high- temperature components operating in severe environments such as nuclear fusion and fission systems owing to its excellent elevated temperature strength and radiation resistance stemming from the addition of extremely thermally stable oxide particles dispersed in a ferritic/martensitic matrix. To realize the structural components such as plates, sheets and tubes in SFR, the development of manufacturing processes is an essential issue for the ODS FM steel. While the ODS steel has superior radiation resistance and high temperature strength, in comparison with the existing commercial steels, it is difficult for the ODS steel to obtain sufficient workability for the fabrication due to high hardness and low ductility at room temperature, meaning that the manufacturing of the ODS plate including cladding tube can be complicated by the low cold workability. In order to prevent the ODS steel from any damage during the manufacturing process, thus, the introduction of intermediate heat treatments between cold rolling processes is necessary. This study investigates effects of the fabrication process parameters such as the cold working ratio, the intermediate and final heat treatments on the microstructure and mechanical properties of 10Cr-1Mo ODS steel. In an effort to optimize the manufacturing route of the ODS FM steel, the microstructural and mechanical evolutions for the ODS plate manufactured by a control of the fabrication process parameters were evaluated in the present study. In the present study, the effect of a cold rolling and intermediate heat treatments on microstructures and mechanical properties of 10Cr-1Mo FM ODS steel were investigated. During the manufacturing route the hardness measurements remained below the critical value of 400 Hv. Intermediate heat treatment with slow cooling led to a softened ferritic structures which can be further

Crystal structures of the solid solutions Na3Zn0.912Cd0.088B5O10 and Na3Zn0.845Mg0.155B5O10

Directory of Open Access Journals (Sweden)

Xue-An Chen

2017-11-01

Full Text Available Two new pentaborates, trisodium zinc cadmium pentaborate, Na3Zn0.912Cd0.088B5O10, and trisodium zinc magnesium pentaborate, Na3Zn0.845Mg0.155B5O10, have been synthesized by high-temperature solution reactions at 1023 K. Their crystal structures were determined by single-crystal X-ray diffraction. Both solid solutions crystallize in the orthorhombic form of the parent compound Na3ZnB5O10 (space group type Pbca, Z = 8 and contain the double ring [B5O10]5− anion composed of one BO4 tetrahedron and four BO3 triangles as the basic structural motif. The anions are bridged by tetrahedrally coordinated and occupationally disordered M2+ (M = Zn/Cd, Zn/Mg cations via common O atoms to form [MB5O10]n3n− layers. The intralayer intersecting channels and the interlayer voids are occupied by Na+ cations to balance the charge.

5,10,15,20-Tetrakis(4-carboxyl phenyl)porphyrin–CdS nanocomposites with intrinsic peroxidase-like activity for glucose colorimetric detection

Energy Technology Data Exchange (ETDEWEB)

Liu, Qingyun, E-mail: qyliu@sdust.edu.cn [School of Chemistry and Environmental Engineering, Shandong University of Science and Technology, Qingdao 266510 (China); Jia, Qingyan; Zhu, Renren; Shao, Qian; Wang, Dongmei; Cui, Peng [School of Chemistry and Environmental Engineering, Shandong University of Science and Technology, Qingdao 266510 (China); Ge, Jiechao, E-mail: jchge2010@mail.ipc.ac.cn [Technical Institute of Physics and Chemistry, Chinese Academy of Sciences, Beijing 100190 (China)

2014-09-01

Here, we describe the design of a novel mimic peroxidase, nanocomposites composed by 5,10,15,20-tetrakis(4-carboxyl phenyl)-porphyrin (H{sub 2}TCPP) and cadmium sulfide (CdS). The H{sub 2}TCPP–CdS nanocomposites can catalyze oxidation of substrate 3,3,5,5-tetramethylbenzidine (TMB) in the presence of H{sub 2}O{sub 2} and form a blue product which can be seen by the naked eye in 5 min. The mechanism of the catalytic reaction originated from the generation of hydroxyl radical (·OH), which is a powerful oxidizing agent to oxidize TMB to produce a blue product. Then, we developed a colorimetric method that is highly sensitive and selective to detect glucose, combined with glucose oxidase (GOx). The proposed method allowed the detection of H{sub 2}O{sub 2} concentration in the range of 4 × 10{sup −6}–1.4 × 10{sup −5} M and glucose in the range of 1.875 × 10{sup −5}–1 × 10{sup −4} M with detectable H{sub 2}O{sub 2} concentration as low as 4.6 × 10{sup −7} M and glucose as low as 7.02 × 10{sup −6} M, respectively. The results provided the theoretical basis of practical application in glucose detecting and peroxidase mimetic enzymes. - Graphical abstract: 5,10,15,20-tetrakis(4-carboxyl phenyl)-porphyrin (H{sub 2}TCPP)–CdS nanohybrids were demonstrated to possess intrinsic peroxidase-like activity and used for a glucose colorimetric sensor. - Highlights: • H{sub 2}TCPP–CdS nanocomposites were synthesized by a facile one step under mild condition. • H{sub 2}TCPP–CdS nanocomposites possess excellent intrinsic peroxidase-like activity. • A sensitive and selective colorimetric sensor for glucose is provided based on H{sub 2}TCPP–CdS nanocomposites. • The generation of hydroxyl radical (·OH) decomposed from H{sub 2}O{sub 2} is contributed to efficient catalytic.

Influence of Z-phase on long-term creep stability of martensitic 9-12% Cr steels

Energy Technology Data Exchange (ETDEWEB)

Danielsen, Hilmar K. [Technical Univ. of Denmark, Lyngby (Denmark). Dept. of Mechanical Engineering; Hald, John [DONG Energy A/S (Denmark); Vattenfall (Denmark)

2010-07-01

The long-term creep strength of the new generation of martensitic creep resistant 9-12%Cr steels since the well-known steel Grade 91 relies strongly on particle strengthening by fine Mn nitrides based on V and Nb. During long-term high-temperature exposures the Mn nitrides may be replaced by the thermodynamically more stable Z-phases (Cr(V,Nb)N) causing a breakdown in creep strength. Cr contents above 10.5% strongly accelerate Z-phase precipitation, which explains the lack of success for all attempts to develop martensitic creep resistant steels with high Cr content for oxidation protection. However 9%Cr steels do not seem to be affected by the Z-phase. Careful control of the Z-phase precipitation process has led to the design of experimental 12%Cr martensitic steels strengthened by fine Z-phase nitrides based on Nb or Ta. Such steels may again enable the combination of high strength and oxidation resistance in the same alloy. This opens a new pathway for further alloy development of the heat resistant martensitic steels. (orig.)

Influence of cooling rate on the structure and mechanical properties of G17CrMoV5 – 10 cast steel

Directory of Open Access Journals (Sweden)

G. Golański

2009-07-01

Full Text Available The paper presents results of research on the influence of cooling rate on the structure and properties of G17CrMoV5 – 10 (L17HMF cast steel. The material for research was a section taken out from an outer cylinder of a steam turbine body after about 250 000 hours of operation at the temperature of 535°C and pressure 9 MPa. The investigated cast steel was subjected to heat treatment which consisted in cooling at the rates corresponding to the processes, such as: bainitic hardening, normalizing and full annealing. Tempering after the process of cooling from austenitizing temperature was carried out at the temperatures of: 700, 720 and 740°C. Performed research has proved that structures obtained after bainitic hardening and normalizing are characterized by a large strength margin which allows to apply high temperatures of tempering. It has been shown that the cast steel of bainitic structure, with similar mechanical properties as the cast steel of bainitic – ferritic structure, is characterized by almost twice as high impact energy. Full annealing and tempering of the examined cast steel ensures only the required impact strength, with mechanical properties comparable to those after service.

Study of the D(p,π+)T and 9Be(p,π+)10Be from 400 to 800MeV

International Nuclear Information System (INIS)

Aslanides, E.; Bauer, T.; Bertini, R.; Beurtey, R.; Bimbot, L.; Bing, O.; Boudard, A.; Brochard, F.; Bruge, G.; Catz, H.; Chaumeaux, A.; Couvert, P.; Duchazeaubeneix, J.C.; Duhm, H.; Garreta, D.; Gorodetzky, P.; Habault, J.; Hibou, F.; Igo, G.; Le Bornec, Y.; Lugol, J.C.; Matoba, M.; Tatischeff, B.; Terrien, Y.

Pion production on CD 2 and 9 Be targets has been observed using the high resolution, energy loss, spectrometer SPES I. Differential cross sections for the D(p,π + ) reaction have been determined at 410, 605 and 809MeV and for the 9 Be(p,π + ) reaction at 410 and 605MeV. The 3.37MeV (2 + ) state in 10 Be is populated preferentially, but a significant part of the transition strength seems to populate the ground state and the higher lying multiplets at about 6.1MeV, 7.4MeV and 9.4MeV [fr

Influence of Mn contents in 0Cr18Ni10Ti thin wall stainless steel tube on TIG girth weld quality

Science.gov (United States)

Liu, Bo

2017-03-01

Three kinds of cold worked 0Cr18Ni10Ti thin wall stainless steel tubes with the manganese contents of 1.27%, 1.35% and 1.44% and the cold worked 0Cr18Ni10Ti stainless steel end plug with manganese content of 1.35% were used for TIG girth welding in the present investigation. The effect of different manganese contents in stainless steel tube on weld quality was studied. The results showed that under the same welding conditions, the metallographic performance of the girth weld for the thin wall stainless steel tube with the manganese element content 1.44% welded with end plug was the best. Under the appropriate welding conditions, the quality of the girth weld increased with the increase of the manganese content till 1.44%. It was found that in the case of the Mn content of 1.44%, and under the proper welding condition the welding defects, such as welding cracks were effectively avoided, and the qualified weld penetration can be obtained.. It is concluded that the appropriate increase of the manganese content can significantly improve the TIG girth weld quality of the cold worked 0Cr18Ni10Ti stainless steel tube.

Polyketide synthase chemistry does not direct biosynthetic divergence between 9- and 10-membered enediynes

Science.gov (United States)

Horsman, Geoff P.; Chen, Yihua; Thorson, Jon S.; Shen, Ben

2010-01-01

Enediynes are potent antitumor antibiotics that are classified as 9- or 10-membered according to the size of the enediyne core structure. However, almost nothing is known about enediyne core biosynthesis, and the determinants of 9- versus 10-membered enediyne core biosynthetic divergence remain elusive. Previous work identified enediyne-specific polyketide synthases (PKSEs) that can be phylogenetically distinguished as being involved in 9- versus 10-membered enediyne biosynthesis, suggesting that biosynthetic divergence might originate from differing PKSE chemistries. Recent in vitro studies have identified several compounds produced by the PKSE and associated thioesterase (TE), but condition-dependent product profiles make it difficult to ascertain a true catalytic difference between 9- and 10-membered PKSE-TE systems. Here we report that PKSE chemistry does not direct 9- versus 10-membered enediyne core biosynthetic divergence as revealed by comparing the products from three 9-membered and two 10-membered PKSE-TE systems under identical conditions using robust in vivo assays. Three independent experiments support a common catalytic function for 9- and 10-membered PKSEs by the production of a heptaene metabolite from: (i) all five cognate PKSE-TE pairs in Escherichia coli; (ii) the C-1027 and calicheamicin cognate PKSE-TEs in Streptomyces lividans K4-114; and (iii) selected native producers of both 9- and 10-membered enediynes. Furthermore, PKSEs and TEs from different 9- and 10-membered enediyne biosynthetic machineries are freely interchangeable, revealing that 9- versus 10-membered enediyne core biosynthetic divergence occurs beyond the PKSE-TE level. These findings establish a starting point for determining the origins of this biosynthetic divergence. PMID:20534556

Self-protective powder wire for semiautomatic welding of corrosion resistant chromium-nickel type 18-10 steels

International Nuclear Information System (INIS)

Lipodaev, V.N.; Kakhovskij, N.I.; Fadeeva, G.V.

1977-01-01

Self-protecting NP-ANV1 powder wire has been developed for welding 18-10 type stainless steels. The use of the wire provides for the same running properties of the welds as the TsL-11 electrodes, the welding being 3-5 times more efficient

Influence of ion implanted helium on deuterium trapping in Kh18N10T stainless steel

International Nuclear Information System (INIS)

Tolstolutskaya, G.D.; Ruzhitskij, V.V.; Kopanets, I.E.

2004-01-01

The results are presented on evolution of distribution profiles and helium and deuterium thermal desorption ion implanted in steel 18Cr10NiTi. Accumulation, trapping, retention and microstructure evolution are studied; effect helium and hydrogen simultaneous implantation on these processes is also studied

Microstructure refinement and strengthening mechanisms of a 9Cr oxide dispersion strengthened steel by zirconium addition

Energy Technology Data Exchange (ETDEWEB)

Xu, Hai Jian; Lu, Zheng; Wang, Dong Mei; Liu, Chunming [Key Laboratory for Anisotropy and Texture of Materials (Ministry of Education), School of Materials Science and Engineering, Northeastern University, Shenyang (China)

2017-02-15

To study the effects of zirconium (Zr) addition on the microstructure, hardness and the tensile properties of oxide dispersion strengthened (ODS) ferritic-martensitic steels, two kinds of 9Cr-ODS ferritic-martensitic steels with nominal compositions (wt.%) of Fe-9Cr-2W-0.3Y{sub 2}O-3 and Fe-9Cr-2W-0.3Zr-0.3Y{sub 2}O{sub 3} were fabricated by the mechanical alloying (MA) of premixed powders and then consolidated by hot isostatic pressing (HIP) techniques. The experimental results showed that the average grain size decreases with Zr addition. The trigonal δ-phase Y{sub 4}Zr{sub 3}O{sub 12} oxides and body-centered cubic Y{sub 2}O{sub 3} oxides are formed in the 9Cr-Zr-ODS steel and 9Cr non-Zr ODS steel, respectively, and the average size of Y{sub 4}Zr{sub 3}O{sub 12} particles is much smaller than that of Y{sub 2}O{sub 3}. The dispersion morphology of the oxide particles in 9Cr-Zr-ODS steel is significantly improved and the number density is 1.1 x 10{sup 23}/m{sup 3} with Zr addition. The 9Cr-Zr-ODS steel shows much higher tensile ductility, ultimate tensile strength and Vickers hardness at the same time.

Sounding rocket flight report, MUMP 9 and MUMP 10

Science.gov (United States)

Grassl, H. J.

1971-01-01

The results of the launching of two-Marshall-University of Michigan Probes (MUMP 9 and MUMP 10), Nike-Tomahawk sounding rocket payloads, are summarized. The MUMP is similar to the thermosphere probe, an ejectable instrument package for studying the variability of the earth's atmospheric parameters. The MUMP 9 payload included an omegatron mass analyzer, a molecular fluorescence densitometer, a mini-tilty filter, and a lunar position sensor. This complement of instruments permitted the determination of the molecular nitrogen density and temperature in the altitude range from approximately 143 to 297 km over Wallops Island, Virginia, during January 1971. The MUMP 10 payload included an omegatron mass analyzer, an electron temperature probe, a cryogenic densitometer, and a solar position sensor. These instruments permitted the determination of the molecular nitrogen density and temperature and the charged particle density and temperature in the altitude range from approximately 145 to 290 km over Wallops Island during the afternoon preceding the MUMP 9 launch.

Round Robin Posttest analysis of a 1/10-scale Steel Containment Vessel Model Test

International Nuclear Information System (INIS)

Komine, Kuniaki; Konno, Mutsuo

1999-01-01

NUPEC and U.S. Nuclear Regulatory Commission (USNRC) have been jointly sponsoring 'Structural Behavior Test' at Sandia National Laboratory (SNL) in Cooperative Containment Research Program'. As one of the test, a test of a mixed scaled SCV model with 1/10 in the geometry and 1/4 in the shell thickness. Round Robin analyses of a 1/10-scale Steel Containment Vessel (SCV) Model Test were carried out to obtain an adequate analytical method among seven organizations belonged to five countries in the world. As one of sponsor, Nuclear Power Engineering Corporation (NUPEC) filled the important role of a posttest analysis of SCV model. This paper describes NUPEC's analytical results in the round robin posttest analysis. (author)

Binding of benzo(a)pyrene and (+/-)-7 beta,8 alpha-dihydroxy-9 alpha, 10 alpha-epoxy-7,8,9, 10-tetrahydrobenzo(a)pyrene to histones

International Nuclear Information System (INIS)

Sculley, T.B.; Zytkovicz, T.H.

1983-01-01

AKR-2B mouse embryo cells were incubated for 24 hr with [3H]benzo(a)pyrene, and the histones were isolated and analyzed using one- and two-dimensional gel electrophoresis and autoradiography. The results revealed that (a) histones H1, H2A, and H3 incorporated significant amounts of label whereas little or no label was associated with histones H2B and H4 and (b) electrophoresis of the histones in the Triton: acid: urea gel system caused labeled histones to have a slower migration than did the corresponding unlabeled histones. Additional studies such as incubation of (+/-)-7 beta,8 alpha-[3H]dihydroxy-9 alpha,10 alpha-epoxy-7,8,9,10-tetrahydrobenzo(a)pyrene with nuclei resulted in radioactive labeling of histones H1, H2A, H2B, and H3 and of high-mobility-group proteins HMG1 and HMG2. The low levels of label associated with histone H4 in the whole-cell and nuclear studies were further investigated by incubating isolated histones with (+/-)-7 beta,8 alpha-[3H]dihydroxy-9 alpha,10 alpha-epoxy-7,8,9,10-tetrahydrobenzo(a)pyrene. Under these conditions, negligible amounts of radioactivity were associated with H4, while significant labeling of H1, H2A, H2B, and H3 and other nuclear proteins was observed. The results suggest that factors other than the presence of suitable nucleophilic acceptor sites on the histones may be necessary for carcinogen binding

Slurry Erosion Behavior of F6NM Stainless Steel and High-Velocity Oxygen Fuel-Sprayed WC-10Co-4Cr Coating

Science.gov (United States)

Cui, S. Y.; Miao, Q.; Liang, W. P.; Huang, B. Z.; Ding, Z.; Chen, B. W.

2017-02-01

WC-10Co-4Cr coating was applied to the surface of F6NM stainless steel by high-velocity oxygen-fuel spraying. The slurry erosion behavior of the matrix and coating was examined at different rotational speeds using a self-made machine. This experiment effectively simulates real slurry erosion in an environment with high silt load. At low velocity (<6 m/s), the main failure mechanism was cavitation. Small bubbles acted as an air cushion, obstructing direct contact between sand and the matrix surface. However, at velocity above 9 m/s, abrasive wear was the dominant failure mechanism. The results indicate that WC-10Co-4Cr coating significantly improved the slurry resistance at higher velocity, because it created a thin and dense WC coating on the surface.

Helminth Infection and Commensal Microbiota Drive Early IL-10 Production in the Skin by CD4+ T Cells That Are Functionally Suppressive.

Directory of Open Access Journals (Sweden)

David E Sanin

2015-05-01

Full Text Available The skin provides an important first line of defence and immunological barrier to invasive pathogens, but immune responses must also be regulated to maintain barrier function and ensure tolerance of skin surface commensal organisms. In schistosomiasis-endemic regions, populations can experience repeated percutaneous exposure to schistosome larvae, however little is known about how repeated exposure to pathogens affects immune regulation in the skin. Here, using a murine model of repeated infection with Schistosoma mansoni larvae, we show that the skin infection site becomes rich in regulatory IL-10, whilst in its absence, inflammation, neutrophil recruitment, and local lymphocyte proliferation is increased. Whilst CD4+ T cells are the primary cellular source of regulatory IL-10, they expressed none of the markers conventionally associated with T regulatory (Treg cells (i.e. FoxP3, Helios, Nrp1, CD223, or CD49b. Nevertheless, these IL-10+ CD4+ T cells in the skin from repeatedly infected mice are functionally suppressive as they reduced proliferation of responsive CD4+ T cells from the skin draining lymph node. Moreover, the skin of infected Rag-/- mice had impaired IL-10 production and increased neutrophil recruitment. Finally, we show that the mechanism behind IL-10 production by CD4+ T cells in the skin is due to a combination of an initial (day 1 response specific to skin commensal bacteria, and then over the following days schistosome-specific CD4+ T cell responses, which together contribute towards limiting inflammation and tissue damage following schistosome infection. We propose CD4+ T cells in the skin that do not express markers of conventional T regulatory cell populations have a significant role in immune regulation after repeated pathogen exposure and speculate that these cells may also help to maintain skin barrier function in the context of repeated percutaneous insult by other skin pathogens.

Booster dose after 10 years is recommended following 17DD-YF primary vaccination.

Science.gov (United States)

Campi-Azevedo, Ana Carolina; Costa-Pereira, Christiane; Antonelli, Lis R; Fonseca, Cristina T; Teixeira-Carvalho, Andréa; Villela-Rezende, Gabriela; Santos, Raiany A; Batista, Maurício A; Campos, Fernanda M; Pacheco-Porto, Luiza; Melo Júnior, Otoni A; Hossell, Débora M S H; Coelho-dos-Reis, Jordana G; Peruhype-Magalhães, Vanessa; Costa-Silva, Matheus F; de Oliveira, Jaquelline G; Farias, Roberto H; Noronha, Tatiana G; Lemos, Jandira A; von Doellinger, Vanessa dos R; Simões, Marisol; de Souza, Mirian M; Malaquias, Luiz C; Persi, Harold R; Pereira, Jorge M; Martins, José A; Dornelas-Ribeiro, Marcos; Vinhas, Aline de A; Alves, Tatiane R; Maia, Maria de L; Freire, Marcos da S; Martins, Reinaldo de M; Homma, Akira; Romano, Alessandro P M; Domingues, Carla M; Tauil, Pedro L; Vasconcelos, Pedro F; Rios, Maria; Caldas, Iramaya R; Camacho, Luiz A; Martins-Filho, Olindo Assis

2016-01-01

A single vaccination of Yellow Fever vaccines is believed to confer life-long protection. In this study, results of vaccinees who received a single dose of 17DD-YF immunization followed over 10 y challenge this premise. YF-neutralizing antibodies, subsets of memory T and B cells as well as cytokine-producing lymphocytes were evaluated in groups of adults before (NVday0) and after (PVday30-45, PVyear1-4, PVyear5-9, PVyear10-11, PVyear12-13) 17DD-YF primary vaccination. YF-neutralizing antibodies decrease significantly from PVyear1-4 to PVyear12-13 as compared to PVday30-45, and the seropositivity rates (PRNT≥2.9Log10mIU/mL) become critical (lower than 90%) beyond PVyear5-9. YF-specific memory phenotypes (effector T-cells and classical B-cells) significantly increase at PVday30-45 as compared to naïve baseline. Moreover, these phenotypes tend to decrease at PVyear10-11 as compared to PVday30-45. Decreasing levels of TNF-α(+) and IFN-γ(+) produced by CD4(+) and CD8(+) T-cells along with increasing levels of IL-10(+)CD4(+)T-cells were characteristic of anti-YF response over time. Systems biology profiling represented by hierarchic networks revealed that while the naïve baseline is characterized by independent micro-nets, primary vaccinees displayed an imbricate network with essential role of central and effector CD8(+) memory T-cell responses. Any putative limitations of this cross-sectional study will certainly be answered by the ongoing longitudinal population-based investigation. Overall, our data support the current Brazilian national immunization policy guidelines that recommend one booster dose 10 y after primary 17DD-YF vaccination.

Expression of Tumor Necrosis Factor Receptor 2 Characterizes TLR9-Driven Formation of Interleukin-10-Producing B Cells

Directory of Open Access Journals (Sweden)

Olga Ticha

2018-01-01

Full Text Available B cell-derived interleukin-10 (IL-10 production has been described as a hallmark for regulatory function in B lymphocytes. However, there is an ongoing debate on the origin of IL-10-secreting B cells and lack of specific surface markers has turned into an important obstacle for studying human B regulatory cells. In this study, we propose that tumor necrosis factor receptor 2 (TNFR2 expression can be used for enrichment of IL-10-secreting B cells. Our data confirm that IL-10 production can be induced by TLR9 stimulation with CpG ODN and that IL-10 secretion accompanies differentiation of peripheral blood B cells into plasma blasts. We further show that CpG ODN stimulation induces TNFR2 expression, which correlates with IL-10 secretion and terminal differentiation. Indeed, flow cytometric sorting of TNFR2+ B cells revealed that TNFR2+ and TNFR2− fractions correspond to IL-10+ and IL-10− fractions, respectively. Furthermore, CpG-induced TNFR2+ B cells were predominantly found in the IgM+ CD27+ B cell subset and spontaneously released immunoglobulin. Finally, our data corroborate the functional impact of TNFR2 by demonstrating that stimulation with a TNFR2 agonist significantly augments IL-10 and IL-6 production in B cells. Altogether, our data highlight a new role for TNFR2 in IL-10-secreting human B lymphocytes along with the potential to exploit this finding for sorting and isolation of this currently ill-defined B cell subset.

Round Robin Posttest analysis of a 1/10-scale Steel Containment Vessel Model Test

Energy Technology Data Exchange (ETDEWEB)

Komine, Kuniaki [Nuclear Power Engineering Corp., Tokyo (Japan); Konno, Mutsuo

1999-07-01

NUPEC and U.S. Nuclear Regulatory Commission (USNRC) have been jointly sponsoring 'Structural Behavior Test' at Sandia National Laboratory (SNL) in Cooperative Containment Research Program'. As one of the test, a test of a mixed scaled SCV model with 1/10 in the geometry and 1/4 in the shell thickness. Round Robin analyses of a 1/10-scale Steel Containment Vessel (SCV) Model Test were carried out to obtain an adequate analytical method among seven organizations belonged to five countries in the world. As one of sponsor, Nuclear Power Engineering Corporation (NUPEC) filled the important role of a posttest analysis of SCV model. This paper describes NUPEC's analytical results in the round robin posttest analysis. (author)

Sounding rocket flight report: MUMP 9 and MUMP 10

Science.gov (United States)

Grassl, H. J.

1971-01-01

The results of the launching of two Marshall-University of Michigan Probes (MUMP 9 and MUMP 10), Nike-Tomahawk sounding rocket payloads, are summarized. The MUMP 9 paylaod included an omegatron mass analyzer, a molecular fluorescence densitometer, a mini-tilty filter, and a lunar position sensor. This complement of instruments permitted the determination of the molecular nitrogen density and temperature in the altitude range from approximately 143 to 297 km over Wallops Island, Virginia, during January 1971. The MUMP 10 payload included an omegatron mass analyzer, an electron temperature probe (Spencer, Brace, and Carignan, 1962), a cryogenic densitometer, and a solar position sensor. This complement of instruments permitted the determination of the molecular nitrogen density and temperature and the charged particle density and temperature in the altitude range from approximately 145 to 290 km over Wallops Island, Virginia, during the afternoon preceding the MUMP 9 launch in January 1971. A general description of the payload kinematics, orientation analysis, and the technique for the reduction and analysis of the data is given.

Emerging roles of BMP9 and BMP10 in hereditary hemorrhagic telangiectasia

Directory of Open Access Journals (Sweden)

Emmanuelle eTillet

2015-01-01

Full Text Available Rendu-Osler-Weber syndrome, also known as hereditary hemorrhagic telangiectasia (HHT, is an autosomal dominant vascular disorder. Three genes are causally related to HHT: the ENG gene encoding endoglin, a co-receptor of the TGFß family (HHT1, the ACVRL1 gene encoding ALK1 (activin receptor-like kinase 1, a type I receptor of the TGFß family (HHT2, and the SMAD4 gene, encoding a transcription factor critical for this signaling pathway. Bone morphogenetic proteins (BMPs are growth factors of the TGFß family. Among them, BMP9 and BMP10 have been shown to bind directly with high affinity to ALK1 and endoglin, and BMP9 mutations have recently been linked to a vascular-anomaly syndrome that has phenotypic overlap with HHT. BMP9 and BMP10 are both circulating cytokines in blood, and the current working model is that BMP9 and BMP10 maintain a quiescent endothelial state that is dependent on the level of ALK1/endoglin activation on endothelial cells. In accordance with this model, to explain the etiology of HHT we hypothesize that a deficient BMP9/BMP10/ALK1/endoglin pathway may lead to re-activation of angiogenesis or a greater sensitivity to an angiogenic stimulus. Resulting endothelial hyperproliferation and hypermigration may lead to vasodilatation and formation of arteriovenous malformation (AVM. HHT would thus result from a defect in the angiogenic balance. This review will focus on the emerging role played by BMP9 and BMP10 in the development of this disease and the therapeutic approaches that this opens.

Strength, running speed, agility and balance profiles of 9- to 10-year ...

African Journals Online (AJOL)

The purpose of this study was to determine the strength, running speed and agility, and balance profiles of 9- to 10-year old learners and the relation between these skills of the learners. Using a stratified random selection from 20 schools with different socio-economic backgrounds, 862 9- to 10-year-old learners (457 boys; ...

On the protective effect of KhOSP-10 inhibitor during corrosion, hydrogenadsorption and corrosion cracking of a steel in sulfuric acid

International Nuclear Information System (INIS)

Mindyuk, A.K.; Svist, E.I.; Savitskaya, O.P.; Goyan, E.B.; Gopanenko, A.N.

1975-01-01

The protective propeties of inhibitor KhOSP-10 in the time of corrosion and corrosive cracking of steel 40Kh are higher then those of inhibitors KPI-1, KI-1, I-I-V etc. Its ability to reduce steel hydrogenation is the same as in the case of KPI-1 inhibitor i.e. below that of KI-1. HCl additives enhance the efficiency of inhibitors KPI-1, KI-1, I-1-V etc. up to the protective ability of KhOSP-10. Kinetics of the electrode processes was estimated from polarization curves

Creep Strength of Dissimilar Welded Joints Using High B-9Cr Steel for Advanced USC Boiler

Science.gov (United States)

Tabuchi, Masaaki; Hongo, Hiromichi; Abe, Fujio

2014-10-01

The commercialization of a 973 K (700 °C) class pulverized coal power system, advanced ultra-supercritical (A-USC) pressure power generation, is the target of an ongoing research project initiated in Japan in 2008. In the A-USC boiler, Ni or Ni-Fe base alloys are used for high-temperature parts at 923 K to 973 K (650 °C to 700 °C), and advanced high-Cr ferritic steels are planned to be used at temperatures lower than 923 K (650 °C). In the dissimilar welds between Ni base alloys and high-Cr ferritic steels, Type IV failure in the heat-affected zone (HAZ) is a concern. Thus, the high B-9Cr steel developed at the National Institute for Materials Science, which has improved creep strength in weldments, is a candidate material for the Japanese A-USC boiler. In the present study, creep tests were conducted on the dissimilar welded joints between Ni base alloys and high B-9Cr steels. Microstructures and creep damage in the dissimilar welded joints were investigated. In the HAZ of the high B-9Cr steels, fine-grained microstructures were not formed and the grain size of the base metal was retained. Consequently, the creep rupture life of the dissimilar welded joints using high B-9Cr steel was 5 to 10 times longer than that of the conventional 9Cr steel welded joints at 923 K (650 °C).

Development of ferromagnetic spinels for optical isolation at 10.6 μm

International Nuclear Information System (INIS)

Teegarden, K.J.

1980-05-01

Vacuum hot pressing was used to fabricate CdCr 2 S 4 , CdCr 2 Se 4 and (1-x) CdCr 2 S 4 .x CdCr 2 Se 4 discs with diameters of 1.25 cm from fine powders and small single crystals to relative densities as high as 99.6%. Optical attenuation coefficients of approx. 1.0 cm -1 at 10.6 m were obtained for CdCr 2 S 4 , and values of 12.1 cm -1 and 14.9 cm -1 for the selenide and sulfur-selenide mixture. Two-and-three-phonon absorption bands were found to limit the transmission of CdCr 2 S 4 at lambda > 10 μm. Extrinsic absorption mechanisms caused the higher attenuation coefficients in CdCr 2 Se 4 and the mixture. The main extrinsic mechanisms at long wavelengths were free carrier absorption (in CdCr 2 Se 4 ) and an impurity absorption band at 16.3 μm due to Cr 2 O 3 . At short wavelengths the attenuation coefficient was dominated by scattering from pores and second phases. Free carrier absorption was found to be induced by free selenium present in the starting powders. Suppression of this absorption was achieved by optimizing the hot-pressing procedure in order to remove free selenium. The presence of pores was attributed to incomplete densification arising from the presence of second phases (CdSe and Cr 2 Se 3 ) and the absence of plastic deformation as a densification mechanism. Laser damage thresholds of 250 MWcm -2 and 100 MWcm -2 were measured at 10.6 μm for CdCr 2 S 4 and CdCr 2 Se 4 , respectively

Quantification by image analysis of grain size of the high temperature phase (austenite) of martensitic steels 9Cr-1Mo

International Nuclear Information System (INIS)

Barcelo, F.; Brachet, J.C.

1993-01-01

In martensitic steels, the austenitic grain size before transformation may influence mechanical properties. 9Cr-1Mo steel (EM10) is used in hexagonal pipes fabrication in fast neutrons reactors. Image analysis allows to quantify the older grain size in function of the austenization heat treatment conditions. (A.B.). 2 figs

The unbound isotopes {sup 9,10}He

Energy Technology Data Exchange (ETDEWEB)

Johansson, H.T. [Fundamental Fysik, Chalmers Tekniska Hoegskola, S-412 96 Goeteborg (Sweden); Aksyutina, Yu. [Fundamental Fysik, Chalmers Tekniska Hoegskola, S-412 96 Goeteborg (Sweden); GSI Helmholtzzentrum fuer Schwerionenforschung GmbH, D-64291 Darmstadt (Germany); Aumann, T.; Boretzky, K. [GSI Helmholtzzentrum fuer Schwerionenforschung GmbH, D-64291 Darmstadt (Germany); Borge, M.J.G. [Instituto Estructura de la Materia, CSIC, E-28006 Madrid (Spain); Chatillon, A. [GSI Helmholtzzentrum fuer Schwerionenforschung GmbH, D-64291 Darmstadt (Germany); Chulkov, L.V. [GSI Helmholtzzentrum fuer Schwerionenforschung GmbH, D-64291 Darmstadt (Germany); Kurchatov Institute, RU-123182 Moscow (Russian Federation); Cortina-Gil, D. [GSI Helmholtzzentrum fuer Schwerionenforschung GmbH, D-64291 Darmstadt (Germany); University of Santiago de Compostela, 15706 Santiago de Compostela (Spain); Datta Pramanik, U. [Saha Institute of Nuclear Physics, 1/AF Bidhannagar, Kolkata 700064 (India); Emling, H. [GSI Helmholtzzentrum fuer Schwerionenforschung GmbH, D-64291 Darmstadt (Germany); Forssen, C. [Fundamental Fysik, Chalmers Tekniska Hoegskola, S-412 96 Goeteborg (Sweden); Fynbo, H.O.U. [Department of Physics and Astronomy, University of Aarhus, DK-8000 Aarhus C (Denmark); Geissel, H.; Ickert, G. [GSI Helmholtzzentrum fuer Schwerionenforschung GmbH, D-64291 Darmstadt (Germany); Jonson, B., E-mail: Bjorn.Jonson@chalmers.s [Fundamental Fysik, Chalmers Tekniska Hoegskola, S-412 96 Goeteborg (Sweden); Physics Department, CERN, CH-1211 Geneve 23 (Switzerland); Kulessa, R. [Instytut Fizyki, Universytet Jagiellonski, PL-30-059 Krakow (Poland); Langer, C. [GSI Helmholtzzentrum fuer Schwerionenforschung GmbH, D-64291 Darmstadt (Germany); Lantz, M. [Fundamental Fysik, Chalmers Tekniska Hoegskola, S-412 96 Goeteborg (Sweden); LeBleis, T.; Mahata, K. [GSI Helmholtzzentrum fuer Schwerionenforschung GmbH, D-64291 Darmstadt (Germany)

2010-10-15

The unbound nuclei {sup 9}He and {sup 10}He have been produced in proton-knockout reactions from a 280 MeV/u {sup 11}Li beam impinging on a liquid hydrogen target at the ALADIN-LAND setup at GSI. Information on their nuclear structure has been obtained from the relative-energy spectra, {sup 8}He+n and {sup 8}He+2n, employing reaction models incorporating the structure of {sup 11}Li. The {sup 8}He+n relative-energy spectrum is dominated by a strong peak-like structure at low energy, which may be interpreted within the effective-range approximation as the result of an s-wave interaction with a neutron scattering length of -3.17(66) fm. This spectrum also shows evidence for resonance states at 1.33(8) MeV and at 2.4 MeV above the {sup 8}He+n threshold. It is argued that the s-state might not be the {sup 9}He ground state. For {sup 8}He+n+n, the analysis of the relative-energy spectrum gives two alternative possibilities for an interpretation: either a narrow resonance at 1.42(10) MeV ({Gamma}=1.11(76) MeV) superimposed on a correlated background, or two overlapping resonances, a ground state at 1.54(11) MeV ({Gamma}=1.91(41) MeV) together with an excited state at 3.99(26) MeV ({Gamma}=1.64(89) MeV). The two possible interpretations are discussed.

Effects of heat treatment condition on the mechanical properties and weldability of 10Cr-1Mo-VNbN cast steel

International Nuclear Information System (INIS)

Shon, Dae Young; Bang, Kook Soo; Lee, Kyong Woon; Chi, Byung Ha

2003-01-01

Mechanical properties and weldability such as HAZ hardness, cold cracking susceptibility and hot ductility of two differently heat treated 10Cr-1Mo-VNbN cast steels were measured and compared. Because of high hardenability of the cast steel, as-annealed cast steel showed martensitic microstructure and thus had higher hardness than annealed-normalized-tempered cast steel which had tempered martensite. Because the welding electrode used resulted in a high hardness weld metal, both cast steels showed same weld metal cold cracking susceptibility even though the as-annealed cast steel had higher HAZ hardness than the annealed-normalized-tempered cast steel. Both cast steels had excellent hot ductility in high temperature range, indicating no risk of grain boundary liquation cracking in the HAZ. However, the as-annealed cast steel showed an inferior ductility in the intermediate temperature range of 1000∼1150 .deg. C because of larger unrecrystallized grain size

Mechanism and kinetic properties for the OH-initiated atmospheric oxidation degradation of 9,10-Dichlorophenanthrene

Energy Technology Data Exchange (ETDEWEB)

Dang, Juan; Shi, Xiangli; Zhang, Qingzhu, E-mail: zqz@sdu.edu.cn; Hu, Jingtian; Wang, Wenxing

2015-02-01

Chlorinated polycyclic aromatic hydrocarbons (ClPAHs) have become a serious environmental concern due to their widespread occurrence and dioxin-like toxicities. In this work, the mechanism of the OH-initiated atmospheric oxidation degradation of 9,10-dichlorophenanthrene (9,10-Cl{sub 2}Phe) was investigated by using high-accuracy quantum chemistry calculations. The rate constants of the crucial elementary reactions were determined by the Rice–Ramsperger–Kassel–Marcus (RRKM) theory. The theoretical results were compared with the available experimental data. The main oxidation products are a group of ring-retaining and ring-opening compounds including chlorophenanthrols, 9,10-dichlorophenanthrene-3,4-dione, dialdehydes, chlorophenanthrenequinones, nitro-9,10-Cl{sub 2}Phe and epoxides et al. The overall rate constant of the OH addition reaction is 2.35 × 10{sup −12} cm{sup 3} molecule{sup −1} s{sup −1} at 298 K and 1 atm. The atmospheric lifetime of 9,10-Cl{sub 2}Phe determined by OH radicals is about 5.05 days. This study provides a comprehensive investigation of the OH-initiated oxidation degradation of 9,10-Cl{sub 2}Phe and should contribute to clarifying its atmospheric fate. - Highlights: • We studied a comprehensive mechanism of OH-initiated degradation of 9,10-Cl{sub 2}Phe. • The atmospheric lifetime of 9,10-Cl{sub 2}Phe determined by OH radical is about 5.05 d. • The rate constants of the crucial elementary steps were evaluated. • Water plays an important role in the formation of nitro-9,10-Cl{sub 2}Phe.

Substitution of modified 9 Cr-1 Mo steel for austentic stainless steels

International Nuclear Information System (INIS)

Sikka, V.K.

1982-04-01

This report describes the current program to develop a high-strength ferritic-martensitic steel. The alloy is essentially Fe-9% Cr-1% Mo with small additions of V and Nb and is known as modifed 9 Cr-1 Mo steel. Its elevated-temperature properties and design allowable stresses match those of type 304 stainless steel for temperatures up to 600 0 C and exceed those of other ferritic steels by factors of 2 to 3. The improved strength of this alloy permits its use in place of stainless steels for many applications

Chemokines beyond chemo-attraction: CXCL10 and its significant role in cancer and autoimmunity.

Science.gov (United States)

Karin, Nathan; Razon, Hila

2018-09-01

Chemokines are mostly known for their chemotactic properties, and less for their ability to direct the biological function of target cells, including T cells. The current review focuses on a key chemokine named CXCL10 and its role in directing the migratory propertied and biological function of CD4+ and CD8+ T cells in the context of cancer and inflammatory autoimmunity. CXCR3 is a chemokine receptor that is abundant on CD4+ T cells, CD8+ T cells and NK cells. It has three known ligands: CXCL9, CXCL10 and CXCL11. Different studies, including those coming form our laboratory, indicated that aside of attracting CD8+ and CD4+ effector T cells to tumor sites and sites of inflammation CXCL10 directs the polarization and potentiates the biological function of these cells. This makes CXCL10 a "key driver chemokine" and a valid target for therapy of autoimmune diseases such as Inflammatory Bowl's Disease, Multiple Sclerosis, Rheumatoid arthritis and others. As for cancer this motivated different groups, including our group to develop CXCL10 based therapies for cancer due to its ability to enhance T-dependent anti cancer immunity. The current review summarizes these findings and their potential translational implication. Copyright © 2018 Elsevier Ltd. All rights reserved.

75 FR 38017 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-9-10 Series Airplanes, DC-9-30...

Science.gov (United States)

2010-07-01

... Airworthiness Directives; McDonnell Douglas Corporation Model DC- 9-10 Series Airplanes, DC-9-30 Series... previously to all known U.S. owners and operators of the McDonnell Douglas Corporation airplanes identified... INFORMATION: On July 15, 2009, we issued AD 2009-15-16, which applies to all McDonnell Douglas Model DC-9-10...

Microstructures and mechanical properties of 9Cr oxide dispersion strengthened steel produced by spark plasma sintering

Energy Technology Data Exchange (ETDEWEB)

Xie, Rui [Key Laboratory for Anisotropy and Texture of Materials (Ministry of Education), School of Materials Science and Engineering, Northeastern University, Shenyang 110819 (China); School of Metallurgy, Northeastern University, Shenyang 110819 (China); Lu, Zheng, E-mail: luz@atm.neu.edu.cn [Key Laboratory for Anisotropy and Texture of Materials (Ministry of Education), School of Materials Science and Engineering, Northeastern University, Shenyang 110819 (China); Lu, Chenyang; Li, Zhengyuan [Key Laboratory for Anisotropy and Texture of Materials (Ministry of Education), School of Materials Science and Engineering, Northeastern University, Shenyang 110819 (China); Ding, Xueyong [School of Metallurgy, Northeastern University, Shenyang 110819 (China); Liu, Chunming [Key Laboratory for Anisotropy and Texture of Materials (Ministry of Education), School of Materials Science and Engineering, Northeastern University, Shenyang 110819 (China)

2017-02-15

Highlights: • A 9Cr-ODS steel was produced by mechanical alloying and spark plasma sintering. • Bimodal grain size distribution was observed. • Formation mechanism of bimodal grain size distribution was discussed. • The size and number density of nanoscale particles were obtained by SAXS and HRTEM. • The contribution of nano-sized particles to yield strength is dominating. - Abstract: 9Cr oxide dispersion strengthened (ODS) steel was fabricated by mechanical alloying (MA) and spark plasma sintering (SPS). The nano-sized particles, grain size distribution and mechanical properties of 9Cr-ODS steel sintered at 950 °C were studied by synchrotron radiation small angle X-ray scattering (SAXS), high-resolution transmission electron microscopy (HRTEM), electron backscatter diffraction (EBSD) and tensile experiment. The results showed that bimodal grain size distribution in the matrix is observed, which is attributed to the heterogeneous recrystallization process during the SPS. High-density nano-sized Y{sub 2}Ti{sub 2}O{sub 7} and some large oxides of Cr{sub 2}Mn(Ti)O{sub 4} are formed in 9Cr-ODS steel. The number density and average size of Y{sub 2}Ti{sub 2}O{sub 7} obtained from SAXS are 4.72 × 10{sup 22}/m{sup 3} and 4.4 nm, respectively. The yield strengths of 9Cr-ODS steel fabricated by SPS are compared with the typical 9Cr-ODS steel produced by HIP.

Changes of structure and properties of cast steels GX10NiCrNb32-20 and GX10NiCrNb3-25 after long-term tempering at 600-1000 C

International Nuclear Information System (INIS)

Gommans, R.; Schrijen, H.; Sundermann, J.; Steinkusch, W.; Hering, W.

2001-01-01

Low-alloy cast steels of type GX 10NiCrNb 32.20 are commonly used for the outlet section of reformer and cracker tubes for the temperature range of 600-1000 C. There was a lack of data on the ductility of the 25%Cr alloyed cast steel GX10NiCrNb 35.25 at room temperature after tempering, which was investigated in a joint project of Pose-Marre and DSM. Mechanical tests were carried out at room temperature and at elevated temperatures. Apart from light microscopy, also SEM/EDX, SAM and TEM analyses were carried out. The 25% alloy has lower ductility than the 20% alloy, owing primarily to the more pronounced development of M 6 C carbide from primary NbC carbide, which takes up Ni and Si during tempering. The microstructure and composition of the M 6 C carbide wre not fully clarified. Information is presented on the potential application of low-carbon materials of the type GX10NiCrNb35.25 [de

A first case of primary amenorrhea with i(X(qter---q10::---qter, rob(13;14(q10;q10, inv(9(p13q33 karyotype

Directory of Open Access Journals (Sweden)

Seema Korgaonkar

2011-01-01

Full Text Available Primary amenorrhea (PA refers to the absence of menarche by the age of 16-18 years although secondary sexual characters are developed. PA occurs in 1-3% of women in the reproductive age group. Various factors such as anatomical, genetic and hormonal factors reported to influence PA. We report triple chromosomal abnormalities of rob(13;14(q10;q10,inv(9(p13q33, i(Xq(qter---q10::---qter in a case of PA and short stature. Though proband has multiple chromosome aberrations, genotypic effect of only i(Xq is evident as proband has PA and short stature. The rob(13;14 and inv(9, which are paternally derived may have role in later reproductive age. Therefore, chromosomal analysis is essential in such cases for the accurate diagnosis and management of the disease.

A Silicon d-spacing Mapping Measurement System With Resolution of 10-9

International Nuclear Information System (INIS)

Zhang Xiaowei; Sugiyama, Hiroshi; Fugimoto, Hiroyuki; Waseda, Atsushi; Takatomi, Toshikazu

2010-01-01

For determination of the Avogadro's number, a self-referenced lattice comparator established at the Photon Factory to deal with a d-spacing mapping measurement over the cross section of a 4 ∼ 5 inches FZ silicon rod. For uncertainty of 1x10 -8 of the unit cell volume, it is necessary to measure lattice parameter of silicon with resolution of 3x10 -9 at least. In this paper, we report the principle of our lattice comparator, characterize our measurement system, and show some mapping measurement results of FZ silicon with resolution of 3x10 -9 .

File list: Pol.Emb.10.AllAg.Mitotic_cycle_8-9 [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available Pol.Emb.10.AllAg.Mitotic_cycle_8-9 dm3 RNA polymerase Embryo Mitotic cycle 8-9 http...://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/Pol.Emb.10.AllAg.Mitotic_cycle_8-9.bed ...

File list: Pol.Emb.10.AllAg.Mitotic_cycle_7-9 [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available Pol.Emb.10.AllAg.Mitotic_cycle_7-9 dm3 RNA polymerase Embryo Mitotic cycle 7-9 http...://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/Pol.Emb.10.AllAg.Mitotic_cycle_7-9.bed ...

Validity and reliability of the Spanish version of the 10-item CD-RISC in patients with fibromyalgia

Science.gov (United States)

2014-01-01

Background No resilience scale has been validated in Spanish patients with fibromyalgia. The aim of this study was to evaluate the validity and reliability of the 10-item CD-RISC in a sample of Spanish patients with fibromyalgia. Methods Design: Observational prospective multicenter study. Sample: Patients with diagnoses of fibromyalgia recruited from primary care settings (N = 208). Instruments: In addition to sociodemographic data, the following questionnaires were administered: Pain Visual Analogue Scale (PVAS), the 10-item Connor-Davidson Resilience scale (10-item CD-RISC), the Fibromyalgia Impact Questionnaire (FIQ), the Hospital Anxiety and Depression Scale (HADS), the Pain Catastrophizing Scale (PCS), the Chronic Pain Acceptance Questionnaire (CPAQ), and the Mindful Attention Awareness Scale (MAAS). Results Regarding construct validity, the factor solution in the Principal Component Analysis (PCA) was considered adequate, so the KMO test had a value of 0.91, and the Barlett’s test of sphericity was significant (χ2 = 852.8; gl = 45; p fibromyalgia, acceptable psychometric properties, with a high level of reliability and validity. PMID:24484847

Determination of susceptibility to intergranular corrosion of stainless steels type X5CrNi18-10 in field

Directory of Open Access Journals (Sweden)

Bore V. Jegdic

2016-12-01

Full Text Available In this paper, the DL EPR method (electrochemical potentiokinetic reactivation with double loop was modified and used to study the susceptibility to intergranular corrosion and stress corrosion cracking of a stainless steel type X5CrNi18-10. The tests were performed in a special electrochemical cell, with the electrolyte in the gel form. Modified DL EPR method is characterized by simple and high accuracy measurements as well as repeatability of the test results. The indicator of susceptibility to intergranular corrosion (Qr/QpGBA obtained by modified DL EPR method is in a very good agreement with the same indicator obtained by standard DL EPR method. The modified DL EPR method is quantitative and highly selective method. Small differences in the susceptibility of the stainless steel type CrNi18-10 to intergranular corrosion and stress corrosion cracking can be determined. Test results can be obtained in a short time. The cost of tests performed by modified DL EPR method is much lower than the cost of tests by conventional chemical methods. Modified DL EPR method can be applied in the field on the stainless steels constructions.

Circulating CXCR5+CD4+ T cells assist in the survival and growth of primary diffuse large B cell lymphoma cells through interleukin 10 pathway

International Nuclear Information System (INIS)

Cha, Zhanshan; Qian, Guangfang; Zang, Yan; Gu, Haihui; Huang, Yanyan; Zhu, Lishuang; Li, Jinqi; Liu, Yang; Tu, Xiaohua; Song, Haihan; Qian, Baohua

2017-01-01

Diffuse large B cell lymphoma (DLBCL) is a common and aggressive cancer caused by the malignant transformation of B cells. Although it has been established that the follicular helper T (Tfh) cells play a central role in B cell development, little information is available on their involvement in DLBCL pathogenesis. We studied the role of the peripheral Tfh equivalent, the CXCR5"+ CD4"+ T cells, in DLBCL. Data showed that compared to CXCR5"- CD4"+ T cells, CXCR5"+ CD4"+ T cells were significantly more effective at promoting the proliferation as well as inhibiting the apoptosis of primary autologous DLBCL tumor cells. Surprisingly, we found that at equal cell numbers, CXCR5"+ CD4"+ T cells in DLBCL patients secreted significantly less interleukin (IL)-21 than CXCR5"- CD4"+ T cells, while the level of IL-10 secretion was significant elevated in the CXCR5"+ compartment compared to the CXCR5"- compartment. Neutralization of IL-10 in the primary DLBCL-CXCR5"+ CD4"+ T cell coculture compromised the CXCR5"+ CD4"+ T cell-mediated pro-tumor effects, in a manner that was dependent on the concentration of anti-IL-10 antibodies. The CXCR5"+ compartment also contained significantly lower frequencies of cytotoxic CD4"+ T cells than the CXCR5"- compartment. In conclusion, our investigations discovered a previously unknown pro-tumor role of CXCR5-expressing circulating CD4"+ T cells, which assisted the survival and proliferation of primary DLBCL cells through IL-10. - Highlights: • We studied the role of the peripheral Tfh in DLBCL. • Tfh were effective at promoting the proliferation of primary DLBCL tumor cells. • Tfh were effective at inhibiting the apoptosis of primary DLBCL tumor cells. • IL-10 secretion in Tfh was significant elevated in DLBCL. • Neutralization of IL-10 compromised Tfh-mediated pro-tumor effects.

Tensile properties and flow behavior analysis of modified 9Cr-1Mo steel clad tube material

Science.gov (United States)

Singh, Kanwarjeet; Latha, S.; Nandagopal, M.; Mathew, M. D.; Laha, K.; Jayakumar, T.

2014-11-01

The tensile properties and flow behavior of modified 9Cr-1Mo steel clad tube have been investigated in the framework of various constitutive equations for a wide range of temperatures (300-923 K) and strain rates (3 × 10-3 s-1, 3 × 10-4 s-1 and 3 × 10-5 s-1). The tensile flow behavior of modified 9Cr-1Mo steel clad tube was most accurately described by Voce equation. The variation of instantaneous work hardening rate (θ = dσ/dε) and σθ with stress (σ) indicated two stage behavior characterized by rapid decrease at low stresses (transient stage) followed by a gradual decrease in high stresses (Stage III). The variation of work hardening parameters and work hardening rate in terms of θ vs. σ and σθ vs. σ with temperature exhibited three distinct regimes. Rapid decrease in flow stress and work hardening parameters and rapid shift of θ vs. σ and σθ vs. σ towards low stresses with increase in temperature indicated dynamic recovery at high temperatures. Tensile properties of the material have been best predicted from Voce equation.

Tensile properties and flow behavior analysis of modified 9Cr–1Mo steel clad tube material

International Nuclear Information System (INIS)

Singh, Kanwarjeet; Latha, S.; Nandagopal, M.; Mathew, M.D.; Laha, K.; Jayakumar, T.

2014-01-01

The tensile properties and flow behavior of modified 9Cr–1Mo steel clad tube have been investigated in the framework of various constitutive equations for a wide range of temperatures (300–923 K) and strain rates (3 × 10 −3 s −1 , 3 × 10 −4 s −1 and 3 × 10 −5 s −1 ). The tensile flow behavior of modified 9Cr–1Mo steel clad tube was most accurately described by Voce equation. The variation of instantaneous work hardening rate (θ = dσ/dε) and σθ with stress (σ) indicated two stage behavior characterized by rapid decrease at low stresses (transient stage) followed by a gradual decrease in high stresses (Stage III). The variation of work hardening parameters and work hardening rate in terms of θ vs. σ and σθ vs. σ with temperature exhibited three distinct regimes. Rapid decrease in flow stress and work hardening parameters and rapid shift of θ vs. σ and σθ vs. σ towards low stresses with increase in temperature indicated dynamic recovery at high temperatures. Tensile properties of the material have been best predicted from Voce equation

File list: Oth.Emb.10.AllAg.Mitotic_cycle_8-9 [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available Oth.Emb.10.AllAg.Mitotic_cycle_8-9 dm3 TFs and others Embryo Mitotic cycle 8-9 SRX0...84383 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/Oth.Emb.10.AllAg.Mitotic_cycle_8-9.bed ...

The effects of adding molybdenum and niobium on the creep strength of 18Cr-10Ni-20Co austenitic steel

International Nuclear Information System (INIS)

Tomono, Yutaka

1987-01-01

The decrease in the creep strength of structural materials during service at elevated temperatures is a very important problem that affects the security of plants and machinery. The improvement in the creep strength of 18Cr-10Ni-20Co austenitic steel achieved through the addition of molybdenum and niobium was studied in tests carried out at 973K and 1,073K. The creep strengthening mechanism was examined using transmission electron micrographs, X-ray diffraction, etc. The results obtained are summarized as follows: (1) The creep strength of low C-18Cr-10Ni-20Co austenitic steel with molybdenum was greatly improved by the addition of niobium up to 1% by weight. In the case of long-term creep, no trend toward decreasing creep strength was observed. (2) The creep strength of austenitic steel possessing a matrix strengthened with molybdenum can be improved through the addition of niobium combined with precipitation hardening with fine carbides precipitated in the grains. (author)

Effect of load ratio and saltwater corrosive environment on the initiation life of fatigue of 10Ni5CrMoV steel

Science.gov (United States)

Xie, Xing; Yi, Hong; Xu, Jian; Gen, Liming; Chen, Luyun

2017-09-01

Fatigue initiation life has been studied with 10CrNi5MoV steel for use in ocean engineering at different load ratios and in different environmental media. The microstructure and micro-topography have been observed and analyzed by means of SEM, EDS and EBSD. Our findings indicate that, the initiation life of 10Ni5CrMoV steel in seawater is shorter than that in air, and the difference in longevity is larger with the increasing of load ratio. Corrosion pits had a great influence on initial corrosion fatigue life.

Mechanism and kinetic properties for the OH-initiated atmospheric oxidation degradation of 9,10-Dichlorophenanthrene.

Science.gov (United States)

Dang, Juan; Shi, Xiangli; Zhang, Qingzhu; Hu, Jingtian; Wang, Wenxing

2015-02-01

Chlorinated polycyclic aromatic hydrocarbons (ClPAHs) have become a serious environmental concern due to their widespread occurrence and dioxin-like toxicities. In this work, the mechanism of the OH-initiated atmospheric oxidation degradation of 9,10-dichlorophenanthrene (9,10-Cl₂Phe) was investigated by using high-accuracy quantum chemistry calculations. The rate constants of the crucial elementary reactions were determined by the Rice-Ramsperger-Kassel-Marcus (RRKM) theory. The theoretical results were compared with the available experimental data. The main oxidation products are a group of ring-retaining and ring-opening compounds including chlorophenanthrols, 9,10-dichlorophenanthrene-3,4-dione, dialdehydes, chlorophenanthrenequinones, nitro-9,10-Cl₂Phe and epoxides et al. The overall rate constant of the OH addition reaction is 2.35 × 10(-12)cm(3) molecule(-1)s(-1) at 298 K and 1 atm. The atmospheric lifetime of 9,10-Cl₂Phe determined by OH radicals is about 5.05 days. This study provides a comprehensive investigation of the OH-initiated oxidation degradation of 9,10-Cl₂Phe and should contribute to clarifying its atmospheric fate. Copyright © 2014 Elsevier B.V. All rights reserved.

Metallographical procedure for detecting carburized layer in the 12Kh18N10T steel tubes

International Nuclear Information System (INIS)

Najmark, S.I.; Shmalenyuk, R.P.

1977-01-01

The various causes of the tendency to intercrystalline corrosion of stainless steel tubing were studied. 12Kh18N10T steel tube specimens were metallographically investigated to reveal the presence and depth of the carburized layer. Unlubricated specimens and specimens with the graphite-saltpeter lubrication applied on them were austenized in the temperature range from 950 to 1250 deg C and then exposed to a provoking anneal at 650 deg C for 24 h. All the lubricated specimens showed a carbide network along grain boundaries and intercrystalline cracks. The specimens treated without lubrication had no cracks. The method offered can differentiate poor tube cleaning and the undesirable effect of other processing steps on the tubes

INFLUENCE OF MODIFICATION ON THE STRUCTURE AND CHARACTERISTICS OF THE STAINLESS STEEL 12X18H10TL

Directory of Open Access Journals (Sweden)

I. V. Zemskov

2004-01-01

Full Text Available There are given the results of investigation of influence of modification by ferrocerium, FS30RZM30B, FSMG, modifier MN, developed in BNTU, ferromolybdenum on the structure and characteristics of the steel 12X18H10TL.

n Vitro Immunomodulatory Effect of R10 Fraction of Garlic on Viability and Production of TNF-? in CD8+ T Cells

OpenAIRE

T. Ghazanfari; H. Rashidi; Sh. Jalaei; P. Alijani

2014-01-01

Introduction & Objective: -cells, especially CD8+ T lymphocytes are the most important cells in anti-tumor response. Previously R10 fraction of garlic extract was reported as an immuno-modulator which induced an effective cellular immunity and Th1 responses. In this study the in vitro immunomodulatory effect of R10 on CD8+ T cells viability and production of TNF-? were evaluated. Materials & Methods: In this experimental study, using monoclonal antibodies attached to magnetic beads with isola...

Changes In Properties and Microstructure of High-Chromium 9-12%Cr Steels Due to Long-Term Exposure at Elevated Temperature

Directory of Open Access Journals (Sweden)

Zieliński A.

2016-06-01

Full Text Available This paper presents the characteristics of the performance of P91 (X10CrMoVNb9-1, P92 (X10CrWMoVNb9-2 and VM12 (X12CrCoWVNb12-2-2 steels used for condition assessment of the pressure components of boilers with supercritical steam parameters. Studies on the mechanical properties, microstructure tests using scanning and transmission electron microscopy, and X-ray analysis of the phase composition of precipitates were performed for selected steels in the as-received condition and after long-term annealing. These steel characteristics are used for the evaluation of the microstructural changes and mechanical properties of the material of components after long-term service. The result of this study is the database of material characteristics representing the mechanical properties related to the microstructure analysis and it can be used for diagnosis of the components of pressure parts of power boilers.

Transformation and Precipitation Kinetics in 30Cr10Ni Duplex Stainless Steel

Science.gov (United States)

Fazarinc, Matevz; Terčelj, Milan; Bombač, David; Kugler, Goran

2010-09-01

To improve the microstructure during casting, hot forming, and heat treatment of 30Cr10Ni duplex stainless steel, accurate data on the precipitation and transformation processes at high temperatures are needed. In this article, the precipitation and transformation processes at various aging times in the temperature range 873 K to 1573 K (600 °C to 1300 °C) were studied. The 30Cr10Ni ferrous alloy contains a relatively large amount of Cr, Ni, and C, which results in a complex microstructure. In addition to the ferrite, austenite, and sigma phase, the M23C6 and MC carbides were also observed in the microstructure. The precipitation of the sigma phase was observed after just 3 minutes of aging, and after 30 minutes of aging at approximately 1053 K (780 °C), its fraction exceeded 40 pct. An intensive austenite-to-ferrite transformation was observed above 1423 K (1150 °C). Optical microscopy, energy-dispersive X-ray spectroscopy (EDS), electron backscattered diffraction (EBSD), and X-ray diffraction (XRD), as well as micro-indentation hardness, hardness, impact toughness, and tensile tests, were carried out to evaluate the obtained microstructures of aged samples.

A two-storey structured photoanode of a 3D Cu2ZnSnS4/CdS/ZnO@steel composite nanostructure for efficient photoelectrochemical hydrogen generation

Science.gov (United States)

Choi, Youngwoo; Baek, Minki; Zhang, Zhuo; Dao, Van-Duong; Choi, Ho-Suk; Yong, Kijung

2015-09-01

photoresponse in the UV to near-IR region, resulting in 47% IPCE in a wide light region from 400 to 500 nm; and the stainless steel mesh serves not only as a conductor for charge transport, but also as a skeleton of the grid structure for absorbing more light. The related mechanism has been investigated, which demonstrates that the two-storey CZTS/CdS/ZnO@steel composite nanostructure would have great potential as a promising photoelectrode with high efficiency and low cost for PEC hydrogen generation. Electronic supplementary information (ESI) available. See DOI: 10.1039/c5nr04107d

Numerical simulation on temperature field of TIG welding for 0Cr18Ni10Ti steel cladding and experimental verification

International Nuclear Information System (INIS)

Luo Hongyi; Tang Xian; Luo Zhifu

2015-01-01

Aiming at tungsten inert gas (TIG) for 0Cr18Ni10Ti stainless steel cladding for radioactive source, the numerical calculation of welding pool temperature field was carried out through adopting ANSYS software. The numerical model of non-steady TIG welding pool shape was established, the heat enthalpy and Gaussian electric arc heat source model of surface distribution were introduced, and the effects of welding current and welding speed to temperature field distribution were calculated. Comparing the experimental data and the calculation results under different welding currents and speeds, the reliability and correctness of the model were proved. The welding technological parameters of 0Cr18Ni10Ti stainless steel were optimized based on the calculation results and the welding procedure was established. (authors)

Helium-induced weld degradation of HT-9 steel

International Nuclear Information System (INIS)

Wang, Chin-An; Chin, B.A.; Lin, Hua T.; Grossbeck, M.L.

1992-01-01

Helium-bearing Sandvik HT-9 ferritic steel was tested for weldability to simulate the welding of structural components of a fusion reactor after irradiation. Helium was introduced into HT-9 steel to 0.3 and 1 atomic parts per million (appm) by tritium doping and decay. Autogenous single pass full penetration welds were produced using the gas tungsten arc (GTA) welding process under laterally constrained conditions. Macroscopic examination showed no sign of any weld defect in HT-9 steel containing 0.3 appm helium. However, intergranular micro cracks were observed in the HAZ of HT-9 steel containing 1 appm helium. The microcracking was attributed to helium bubble growth at grain boundaries under the influence of high stresses and temperatures that were present during welding. Mechanical test results showed that both yield strength (YS) and ultimate tensile strength (UTS) decreased with increasing temperature, while the total elongation increased with increasing temperature for all control and helium-bearing HT-9 steels

42 CFR 9.10 - Occupational Health and Safety Program (OHSP) and biosafety requirements.

Science.gov (United States)

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Occupational Health and Safety Program (OHSP) and... SANCTUARY SYSTEM § 9.10 Occupational Health and Safety Program (OHSP) and biosafety requirements. (a) How are employee Occupational Health and Safety Program risks and concerns addressed? The sanctuary shall...

The Development of Plasmodium falciparum-Specific IL10 CD4 T Cells and Protection from Malaria in Children in an Area of High Malaria Transmission.

Science.gov (United States)

Boyle, Michelle J; Jagannathan, Prasanna; Bowen, Katherine; McIntyre, Tara I; Vance, Hilary M; Farrington, Lila A; Schwartz, Alanna; Nankya, Felistas; Naluwu, Kate; Wamala, Samuel; Sikyomu, Esther; Rek, John; Greenhouse, Bryan; Arinaitwe, Emmanuel; Dorsey, Grant; Kamya, Moses R; Feeney, Margaret E

2017-01-01

Cytokine-producing CD4 T cells have important roles in immunity against Plasmodium falciparum (Pf) malaria. However, the factors influencing functional differentiation of Pf- specific CD4 T cells in naturally exposed children are not well understood. Moreover, it is not known which CD4 T-cell cytokine-producing subsets are most critical for protection. We measured Pf- specific IFNγ-, IL10-, and TNFα-producing CD4 T-cell responses by multi-parametric flow cytometry in 265 children aged 6 months to 10 years enrolled in a longitudinal observational cohort in a high malaria transmission site in Uganda. We found that both age and parasite burden were independently associated with cytokine production by CD4 T cells. IL10 production by IFNγ + CD4 T cells was higher in younger children and in those with high-parasite burden during recent infection. To investigate the role of CD4 T cells in immunity to malaria, we measured associations of Pf -specific CD4 cytokine-producing cells with the prospective risk of Pf infection and clinical malaria, adjusting for household exposure to Pf -infected mosquitos. Overall, the prospective risk of infection was not associated with the total frequency of Pf- specific CD4 T cells, nor of any cytokine-producing CD4 subset. However, the frequency of CD4 cells producing IL10 but not inflammatory cytokines (IFNγ and TNFα) was associated with a decreased risk of clinical malaria once infected. These data suggest that functional polarization of the CD4 T-cell response may modulate the clinical manifestations of malaria and play a role in naturally acquired immunity.

Circulating CXCR5+CD4+ T cells assist in the survival and growth of primary diffuse large B cell lymphoma cells through interleukin 10 pathway

Energy Technology Data Exchange (ETDEWEB)

Cha, Zhanshan [Department of Transfusion, Changhai Hospital, Second Military Medical University, Shanghai 200433 (China); Qian, Guangfang [Department of Endocrinology, Zhangqiu Municipal Hospital of Traditional Chinese Medicine, Zhangqiu, Shandong 250200 (China); Zang, Yan; Gu, Haihui; Huang, Yanyan; Zhu, Lishuang; Li, Jinqi; Liu, Yang; Tu, Xiaohua [Department of Transfusion, Changhai Hospital, Second Military Medical University, Shanghai 200433 (China); Song, Haihan [Emergency Center, East Hospital, Shanghai 200120 (China); Qian, Baohua, E-mail: qianbhl963@163.com [Department of Transfusion, Changhai Hospital, Second Military Medical University, Shanghai 200433 (China)

2017-01-01

Diffuse large B cell lymphoma (DLBCL) is a common and aggressive cancer caused by the malignant transformation of B cells. Although it has been established that the follicular helper T (Tfh) cells play a central role in B cell development, little information is available on their involvement in DLBCL pathogenesis. We studied the role of the peripheral Tfh equivalent, the CXCR5{sup +} CD4{sup +} T cells, in DLBCL. Data showed that compared to CXCR5{sup -} CD4{sup +} T cells, CXCR5{sup +} CD4{sup +} T cells were significantly more effective at promoting the proliferation as well as inhibiting the apoptosis of primary autologous DLBCL tumor cells. Surprisingly, we found that at equal cell numbers, CXCR5{sup +} CD4{sup +} T cells in DLBCL patients secreted significantly less interleukin (IL)-21 than CXCR5{sup -} CD4{sup +} T cells, while the level of IL-10 secretion was significant elevated in the CXCR5{sup +} compartment compared to the CXCR5{sup -} compartment. Neutralization of IL-10 in the primary DLBCL-CXCR5{sup +} CD4{sup +} T cell coculture compromised the CXCR5{sup +} CD4{sup +} T cell-mediated pro-tumor effects, in a manner that was dependent on the concentration of anti-IL-10 antibodies. The CXCR5{sup +} compartment also contained significantly lower frequencies of cytotoxic CD4{sup +} T cells than the CXCR5{sup -} compartment. In conclusion, our investigations discovered a previously unknown pro-tumor role of CXCR5-expressing circulating CD4{sup +} T cells, which assisted the survival and proliferation of primary DLBCL cells through IL-10. - Highlights: • We studied the role of the peripheral Tfh in DLBCL. • Tfh were effective at promoting the proliferation of primary DLBCL tumor cells. • Tfh were effective at inhibiting the apoptosis of primary DLBCL tumor cells. • IL-10 secretion in Tfh was significant elevated in DLBCL. • Neutralization of IL-10 compromised Tfh-mediated pro-tumor effects.

LX-10 Explosive Damage Studies

Science.gov (United States)

2015-03-03

opposite end of the vessel. The inside of the bomb is fitted with a stainless steel liner to protect the inner surface and to change the bomb...19  18. Size Fractions for Spherical LX-10 Samples Impact Damaged Between 312 and 416 ft/s...19  19. Spherical LX-10 Sample Impact Damaged at 416 ft/s ....................................... 20  20

49 CFR 179.300-10 - Postweld heat treatment.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Postweld heat treatment. 179.300-10 Section 179.300-10 Transportation Other Regulations Relating to Transportation PIPELINE AND HAZARDOUS MATERIALS... Postweld heat treatment. After welding is complete, steel tanks and all attachments welded thereto, must be...

Creep and creep fatigue crack behavior of 1Cr- and 9Cr-steels

International Nuclear Information System (INIS)

Maile, K.; Klenk, A.; Schellenberg, G.; Granacher, J.; Tramer, M.

2000-01-01

A large database for creep crack initiation and propagation under constant load conditions is available on conventional power plant steels of types 1%Cr and 12%Cr. Modern plants are often used in the medium and peak load regime, thus the dominant loading situation in high temperature components is creep fatigue. For life assessment data about crack initiation and growth under creep fatigue loading are required. These characteristics can not be substituted by pure fatigue or creep crack data. Therefore, a comprehensive test programme was started to investigate the creep fatigue crack behaviour of a 1%CrMoNiV turbine rotor steel (30CrMoNiV 4 11) at 550 C and a new 9%CrMoVNb pipe steel (type P 9 1) at 600 C. DENT-specimen with 15 and 60 mm thickness as well as side grooved CT-specimen with 25 and 50 mm thickness have been tested to determine possible influences of geometry and thus to check the transferability of the data to components. The creep fatigue crack growth results of tests with dwell times between t H = 0,32h and 10 h lie in the scatterbands given by creep crack growth results. Nevertheless a higher crack growth rate under creep fatigue conditions can be stated. An increase in crack growth rate due to creep fatigue is clearly visible. Loading situations with frequencies higher than 1.10 -4 Hz should be not assessed with pure creep crack results or sufficient safety margins have to be applied. (orig.)

Immunohistochemical Expression of CD-10, BCL-6 and MUM-1 Antibodies and Immediate Clinical Response in Patients of Diffuse Large B-Cell Lymphomas after Six Cycles of Chemotherapy

International Nuclear Information System (INIS)

Hassan, U.; Ishtiaq, S.; Hussain, M.

2014-01-01

Objective: To determine the expression of CD-10, BCL-6 and MUM-1 in patients with diffuse large B-cell lymphoma (DLBCL) and its association with immediate clinical response after six cycles of CHOP chemotherapy. Study Design: Analytical study. Place and Duration of Study: Armed Forces Institute of Pathology (AFIP), Rawalpindi in collaboration with Nuclear medicine, Oncology and Radiotherapy Institute (NORI), Islamabad from September 2010 to September 2011. Methodology: CD-10, BCL-6 and MUM-1 antibodies were applied on cases diagnosed as DLBCL. Immediate clinical response was noted after 6 cycles of chemotherapy with the help of oncologist and divided into complete response, partial response, stable disease and relapse/ progression. Patient's age, results of expression of CD-10, BCL-6 and MUM-1 and results of immediate clinical response to chemotherapy were noted. Regarding analysis of prognostic markers (CD-10, BCL-6 and MUM-1), chi-square test was used for immediate clinical response to chemotherapy in DLBCL. Results: CD-10 was positive in 40% cases, BCL-6 in 58.7% cases and MUM-1 was positive in 46.7% cases. About 41.3% of patients showed complete response, 10.6% partial response, 17.3% stable disease and 30.8% showed relapse/progression. CD-10 expression in DLBCL was associated with better immediate clinical response (p = 0.011) whereas MUM-1 expression in DLBCL was associated with poor immediate clinical response (p < 0.0001). However, there was no statistically significant association of BCL-6 with immediate clinical response (p = 0.22). Conclusion: DLBCL shows expression of CD-10, BCL-6 and MUM-1 in nearly fifty percent of the cases. CD-10 is associated with good whereas MUM is associated with poor response. However, there was no association of BCL-6 with immediate clinical response. (author)

C-Reactive Protein (CRP), Interferon Gamma-Inducible Protein 10 (IP-10), and Lipopolysaccharide (LPS) Are Associated with Risk of Tuberculosis after Initiation of Antiretroviral Therapy in Resource-Limited Settings

Science.gov (United States)

Tenforde, Mark W.; Gupte, Nikhil; Dowdy, David W.; Asmuth, David M.; Balagopal, Ashwin; Pollard, Richard B.; Sugandhavesa, Patcharaphan; Lama, Javier R.; Pillay, Sandy; Cardoso, Sandra W.; Pawar, Jyoti; Santos, Breno; Riviere, Cynthia; Mwelase, Noluthando; Kanyama, Cecilia; Kumwenda, Johnstone; Hakim, James G.; Kumarasamy, Nagalingeswaran; Bollinger, Robert; Semba, Richard D.; Campbell, Thomas B.; Gupta, Amita

2015-01-01

Objective The association between pre-antiretroviral (ART) inflammation and immune activation and risk for incident tuberculosis (TB) after ART initiation among adults is uncertain. Design Nested case-control study (n = 332) within ACTG PEARLS trial of three ART regimens among 1571 HIV-infected, treatment-naïve adults in 9 countries. We compared cases (participants with incident TB diagnosed by 96 weeks) to a random sample of controls (participants who did not develop TB, stratified by country and treatment arm). Methods We measured pre-ART C-reactive protein (CRP), EndoCab IgM, ferritin, interferon gamma (IFN-γ), interleukin 6 (IL-6), interferon gamma-inducible protein 10 (IP-10), lipopolysaccharide (LPS), soluble CD14 (sCD14), tumor necrosis factor alpha (TNF-α), and CD4/DR+/38+ and CD8/DR+/38+ T cells. Markers were defined according to established cutoff definitions when available, 75th percentile of measured values when not, and detectable versus undetectable for LPS. Using logistic regression, we measured associations between biomarkers and incident TB, adjusting for age, sex, study site, treatment arm, baseline CD4 and log10 viral load. We assessed the discriminatory value of biomarkers using receiver operating characteristic (ROC) analysis. Results Seventy-seven persons (4.9%) developed incident TB during follow-up. Elevated baseline CRP (aOR 3.25, 95% CI: 1.55–6.81) and IP-10 (aOR 1.89, 95% CI: 1.05–3.39), detectable plasma LPS (aOR 2.39, 95% CI: 1.13–5.06), and the established TB risk factors anemia and hypoalbuminemia were independently associated with incident TB. In ROC analysis, CRP, albumin, and LPS improved discrimination only modestly for TB risk when added to baseline routine patient characteristics including CD4 count, body mass index, and prior TB. Conclusion Incident TB occurs commonly after ART initiation. Although associated with higher post-ART TB risk, baseline CRP, IP-10, and LPS add limited value to routine patient characteristics

Regulatory Eosinophils Suppress T Cells Partly through Galectin-10.

Science.gov (United States)

Lingblom, Christine; Andersson, Jennie; Andersson, Kerstin; Wennerås, Christine

2017-06-15

Eosinophils have the capacity to regulate the function of T cell subsets. Our aim was to test the hypothesis of the existence of a regulatory subset of eosinophils. Human eosinophils were incubated with T cells that were stimulated with allogeneic leukocytes or CD3/CD28 cross-linking. After 2 d of coculture, 11% of the eosinophils gained CD16 expression. A CD16 hi subset of eosinophils, encompassing 1-5% of all eosinophils, was also identified in the blood of healthy subjects. FACS sorting showed that these CD16 hi eosinophils were significantly stronger suppressors of T cell proliferation than were conventional CD16 neg eosinophils. Human eosinophils contain stores of the immunoregulatory protein galectin-10. We found that Ab-mediated neutralization of galectin-10 partially abrogated the suppressive function of the eosinophils. Moreover, recombinant galectin-10 by itself was able to suppress T cell proliferation. Finally, we detected galectin-10-containing immune synapses between eosinophils and lymphocytes. To conclude, we describe a subset of suppressive eosinophils expressing CD16 that may escape detection because CD16-based negative selection is the standard procedure for the isolation of human eosinophils. Moreover, we show that galectin-10 functions as a T cell-suppressive molecule in eosinophils. Copyright © 2017 by The American Association of Immunologists, Inc.

Tensile properties and flow behavior analysis of modified 9Cr–1Mo steel clad tube material

Energy Technology Data Exchange (ETDEWEB)

Singh, Kanwarjeet, E-mail: kanwar722@yahoo.com; Latha, S.; Nandagopal, M.; Mathew, M.D.; Laha, K.; Jayakumar, T.

2014-11-15

The tensile properties and flow behavior of modified 9Cr–1Mo steel clad tube have been investigated in the framework of various constitutive equations for a wide range of temperatures (300–923 K) and strain rates (3 × 10{sup −3} s{sup −1}, 3 × 10{sup −4} s{sup −1} and 3 × 10{sup −5} s{sup −1}). The tensile flow behavior of modified 9Cr–1Mo steel clad tube was most accurately described by Voce equation. The variation of instantaneous work hardening rate (θ = dσ/dε) and σθ with stress (σ) indicated two stage behavior characterized by rapid decrease at low stresses (transient stage) followed by a gradual decrease in high stresses (Stage III). The variation of work hardening parameters and work hardening rate in terms of θ vs. σ and σθ vs. σ with temperature exhibited three distinct regimes. Rapid decrease in flow stress and work hardening parameters and rapid shift of θ vs. σ and σθ vs. σ towards low stresses with increase in temperature indicated dynamic recovery at high temperatures. Tensile properties of the material have been best predicted from Voce equation.

Ethiop. J. Sci. & Technol. 9(1) 31-44, 2016 31 Investigation of 1, 10 ...

African Journals Online (AJOL)

9(1) 31-44, 2016. 31. Investigation of 1, 10-Phenanthroline based Ionic Liquids using X-ray photoelectron spectroscopy ... 1, 10-Phenanthrolinium based ionic liquids are among the new compounds ..... Chemical Reviews 102(10):3667-. 3692.

File list: NoD.Emb.10.AllAg.Mitotic_cycle_7-9 [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Emb.10.AllAg.Mitotic_cycle_7-9 dm3 No description Embryo Mitotic cycle 7-9 http...://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/NoD.Emb.10.AllAg.Mitotic_cycle_7-9.bed ...

Electronic effects in emission of core/shell CdSe/ZnS quantum dots conjugated to anti-Interleukin 10 antibodies

Energy Technology Data Exchange (ETDEWEB)

Quintos Vazquez, A.L. [ESIME—Instituto Politécnico Nacional, México D. F. 07738, México (Mexico); Torchynska, T.V., E-mail: ttorch@esfm.ipn.mx [ESFM–Instituto Politécnico Nacional, México D. F. 07738, México (Mexico); Casas Espinola, J.L. [ESFM–Instituto Politécnico Nacional, México D. F. 07738, México (Mexico); Jaramillo Gómez, J.A.; Douda, J. [UPIITA–Instituto Politécnico Nacional, México D. F. 07320, México (Mexico)

2013-11-15

The paper presents a comparative study of the photoluminescence (PL) and Raman scattering spectra of the core–shell CdSe/ZnS quantum dots (QDs) in nonconjugated states and after the conjugation to anti-Interleukin 10 antibodies (anti-IL10). All optical measurements are performed on the dried droplets of the original solution of nonconjugated and bioconjugated QDs located on the Si substrate. CdSe/ZnS QDs with emission at 605 and 655 nm have been used. PL spectra of nonconjugated QDs are characterized by one Gaussian shape PL band related to the exciton emission in the CdSe core. PL spectra of bioconjugated QDs have changed essentially: the core PL band shifts into the high energy spectral range (“blue” sift) and becomes asymmetric. Additionally two new PL bands appear. A set of physical reasons has been proposed for the “blue” shift explanation for the core PL band in bioconjugated QDs. Then Raman scattering spectra have been studied with the aim to analyze the impact of elastic strains or the oxidation process at the QD bioconjugation. The variation of PL spectra versus excitation light intensities has been studied to analyze the exciton emission via excited states in QDs. Finally the PL spectrum transformation for the core emission in bioconjugated QDs has been attributed to the electronic quantum confined effects stimulated by the electric charges of bioconjugated antibodies. -- Highlights: • The conjugation of CdSe/ZnS QDs to anti-Interleukin 10 antibodies has been studied. • PL shift to high energy is detected in bioconjugated CdSe/ZnS QDs. • The PL energy shift in bioconjugated QDs is stimulated by antibody electric charges. • The reasons of PL energy shift in bioconjugated QDs have been discussed.

Systematic analysis of above-barrier fusion of 9,10,11Be+209Bi

International Nuclear Information System (INIS)

Hinde, D. J.; Dasgupta, M.

2010-01-01

Measurements of fusion for 9,10,11 Be allow testing of the relative importance to fusion and breakup of the α-cluster structure found in all these Be isotopes, compared with the neutron-halo structure only present for 11 Be. However, disagreements exist among different published experimental data sets for the reactions of 9,10,11 Be with 209 Bi. Accurate measurements of above-barrier cross sections for the products of complete fusion (fission and evaporation residues) in the reaction of 9 Be with 209 Bi and 208 Pb provide the basis for a reanalysis of above-barrier fusion for 10,11 Be+ 209 Bi. This includes procedures making full use of the higher precision stable beam data and resolves many of the disagreements. The improved self-consistency of the analysis allows investigation of the experimental average fusion barriers. Although showing some scatter, these suggest a higher barrier for the neutron halo nucleus 11 Be. Comparison of published cross sections for fusion associated with capture of all the charge of the projectile suggest that all these Be isotopes show significant suppression of complete fusion, a surprising result given that the α-breakup threshold energies are 1.57 MeV for 9 Be but over 7 MeV for 10,11 Be. Further experimental studies to investigate in more detail the division between complete and incomplete fusion for reactions of 10,11 Be are needed.

10 CFR 95.9 - Communications.

Science.gov (United States)

2010-01-01

...: (a) By mail addressed to: ATTN: Document Control Desk, Director, Division of Security Operations...) Where practicable, by electronic submission, for example, Electronic Information Exchange, or CD-ROM. Electronic submissions must be made in a manner that enables the NRC to receive, read, authenticate...

Thermal conductivity and thermal expansion of stainless steels D9 and HT9

International Nuclear Information System (INIS)

Leibowitz, L.; Blomquist, R.A.

1988-01-01

Renewed interest in the use of metallic fuels in liquid-metal fast breeder reactors has prompted study of the thermodynamic and transport properties of its materials. Two stainless steels are of particular interest because of their good performance under irradiation. These are D9, an austenitic steel, and HT9, a ferritic steel. Thermal conductivity and thermal expansion data for these alloys are of particular interest in assessing in-reactor behavior. Because literature data were inadequate, measurements of these two properties for the two steels were performed and are reported to 1200 K. Of particular interest is the influence on these properties of a phase transition in HT9

BMP9 and BMP10 are necessary for proper closure of the ductus arteriosus

Science.gov (United States)

Levet, Sandrine; Ouarné, Marie; Ciais, Delphine; Coutton, Charles; Subileau, Mariela; Mallet, Christine; Ricard, Nicolas; Bidart, Marie; Debillon, Thierry; Faravelli, Francesca; Rooryck, Caroline; Feige, Jean-Jacques; Tillet, Emmanuelle; Bailly, Sabine

2015-01-01

The transition to pulmonary respiration after birth requires rapid alterations in the structure of the mammalian cardiovascular system. One dramatic change that occurs is the closure of the ductus arteriosus (DA), an arterial connection in the fetus that directs blood flow away from the pulmonary circulation. Two members of the TGFβ family, bone morphogenetic protein 9 (BMP9) and BMP10, have been recently involved in postnatal angiogenesis, both being necessary for remodeling of newly formed microvascular beds. The aim of the present work was to study whether BMP9 and BMP10 could be involved in closure of the DA. We found that Bmp9 knockout in mice led to an imperfect closure of the DA. Further, addition of a neutralizing anti-BMP10 antibody at postnatal day 1 (P1) and P3 in these pups exacerbated the remodeling defect and led to a reopening of the DA at P4. Transmission electron microscopy images and immunofluorescence stainings suggested that this effect could be due to a defect in intimal cell differentiation from endothelial to mesenchymal cells, associated with a lack of extracellular matrix deposition within the center of the DA. This result was supported by the identification of the regulation by BMP9 and BMP10 of several genes known to be involved in this process. The involvement of these BMPs was further supported by human genomic data because we could define a critical region in chromosome 2 encoding eight genes including BMP10 that correlated with the presence of a patent DA. Together, these data establish roles for BMP9 and BMP10 in DA closure. PMID:26056270

Accuracy of 9Be-data and its influence on 10Be cosmogenic nuclide data

International Nuclear Information System (INIS)

Merchel, S.; Schaefer, U.; Bremser, W.; Recknagel, S.; Bourles, D.L.; Leanni, L.; Czeslik, U.; Erzinger, J.; Kummer, N.A.; Merkel, B.

2013-01-01

A 9 Be-solution has been chemically prepared from phenakite (Be 2 SiO 4 ) mineral grains as commercial 9 Be-solutions are too high in long-lived 10 Be. The solution is intended to be used as a carrier for radiochemical separation of 10 Be to be measured by accelerator mass spectrometry (AMS). Thus, accurate data of the 9 Be-concentration of this solution is essential to guarantee for high-accuracy 10 Be data in the future. After devastating preliminary results (∼8 % standard deviation), eight laboratories finally produced twelve individual results by four different analytical methods. A certain lab and method bias might be identified by sophisticated statistical evaluation. Some laboratories also (grossly) underestimate their uncertainties. Thus, the simple weighted mean of this round-robin exercise needed to be corrected by introducing additional allowances (Paule-Mandel-approach). The final result has been calculated to (2,246 ± 11) μg 9 Be/(g solution) with a reasonably low weighted standard deviation of 0.49 %. The maximum deviation of a single lab value from the weighted mean is 2.4 % when removing one Grubbs outlier (11 % off from the mean) from the data set. As 10 Be-data, which is usually calculated from measured 10 Be/ 9 Be by AMS and stable 9 Be, cannot be more accurate than the determined 9 Be-concentration, it seems highly advisable to establish or improve quality assurance by having self-made carrier-solutions analysed at more than a single lab and regularly taking part in round-robin exercises. (author)

49 CFR 179.100-10 - Postweld heat treatment.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Postweld heat treatment. 179.100-10 Section 179...-10 Postweld heat treatment. (a) After welding is complete, steel tanks and all attachments welded... treatment is prohibited. (c) Tank and welded attachments, fabricated from ASTM A 240/A 240M (IBR, see § 171...

10 CFR 9.41 - Requests for waiver or reduction of fees.

Science.gov (United States)

2010-01-01

... publication fee; and (8) Describe any commercial or private interest the requester or any other party has in... 10 Energy 1 2010-01-01 2010-01-01 false Requests for waiver or reduction of fees. 9.41 Section 9... Requests for waiver or reduction of fees. (a)(1) The NRC will collect fees for searching for, reviewing...

Susceptibility to stress corrosion in stainless steels type AISI 321 and 12X18H10T used in PWR type reactors (WWER); Susceptibilidad a la corrosion bajo esfuerzo de barras de acero inoxidable AISI 321 y 12X18H10T en ambientes utilizados en reactores VVER

Energy Technology Data Exchange (ETDEWEB)

Matadamas C, N

1996-12-31

Titanium stabilized stainless steels have been utilized in sovietic pressurized water reactors (VVER) for avoid the susceptibility to Intergranular Corrosion (IGC) present in other austenitic stainless steels. However the Intergranular Corrosion resistance of this kind of materials has been questioned because of Intergranular Stress Corrosion Cracking failures (IGSCC) have been reported. This paper study the electrochemical behavior of the AISI 321 stainless steel in a H{sub 3}BO{sub 3} Solution contaminated with chlorides and its susceptibility to Intergranular Corrosion.Electrochemical prediction diagrams of the stainless steels AISI 321 and 12X18H10T (sovietic) sensitized (600 Centigrade, 3 h.) were compared. Cylindrical and conical samples were used in Slow Strain Rate Tests (SSRT), to determine the susceptibility to Stress Corrosion Cracking (SCC) in AISI 321 and 12X18H10T stainless steels. The results obtained showed that the temperature of the solution is a very important factor to detect this susceptibility. Fractography studies on the fracture surfaces of the samples obtained in the SSRT at high temperature were realized. Corrosion velocities of both AISI 321 and 12X18H10T stainless steels were determined using conical samples in the CERT system at high temperature. E.D.A.X. analysis was employed in both AISI 321 and 12X18H10T stainless steels in order to explain the degree of sensitization. (Author).

Expression of KAI1/CD82 and MRP-1/CD9 in transitional cell carcinoma of bladder.

Science.gov (United States)

Ai, Xing; Zhang, Xu; Wu, Zhun; Ma, Xin; Ju, Zhenghua; Wang, Baojun; Shi, Taoping

2007-02-01

The expression of KAI1/CD82 and MRP-1/CD9 in transitional cell carcinoma of bladder (TCCB) and its clinical significance were investigated. Immunohistochemistry was used to detect KAI1/CD82 and MRP-1/CD9 protein expression in 52 TCCB specimens. Correlation between the expression of KAI1/CD82 and MRP-1/CD9 to clinicopathologic factors was statistically analyzed. The results showed that the positive rate of KAI1/CD82 and MRP-1/CD9 in TCCB was 50% and 61.5%, respectively. The MRP-1/CD9 and KAI1/CD82 expression was significantly associated with grade of TCCB (PMRP-1/CD9 or KAI1/CD82 expression and clinical stage of TCCB (P>0.05). The expression level of MRP-1/CD9 and KAI1/CD82 in recurrent TCCB samples was lower than that in non-recurrent samples (PMRP-1/CD9 expression was statistically significant (r=0.316, PMRP-1/CD9 expression may be important prognostic indicators and potentially useful for assessing the biological behavior of TCCB.

Long-term Stability of 9- to 12 % Cr Steels

DEFF Research Database (Denmark)

Hald, John

2004-01-01

In the recent 25 years creep rupture strength of 9- to 12 %Cr steels for steam pipes and turbines has been doubled by development of new alloys. This development has formed a basis for improved efficiency of fossil fired steam power plants by introduction of advanced steam temperatures...... and pressures. Newly developed steam pipe steels are based on modifications of well-established steels like the X 20CrMoV12 1. Balanced addition of V, Nb and N to a 9Cr 1 Mo steel led to the Modified 9 Cr steel P 91. Addition of 1% W to a 9Cr 1 MoVNbN base composition led to steel E 911 and partial replacement...... of Mo with 1.8 % W combined with a slight amount of Boron led to steel P 92. The creep rupture strength of these new alloys are now secured with long-term tests up to 100,000 hours, which demonstrate improvements of 50% (P 91), 75 % (E 911) and 100 % (P 92) in strength compared to X 20CrMoV12 1....

Gravity model improvement using GEOS 3 /GEM 9 and 10/. [and Seasat altimetry data

Science.gov (United States)

Lerch, F. J.; Wagner, C. A.; Klosko, S. M.; Laubscher, R. E.

1979-01-01

Although errors in previous gravity models have produced large uncertainties in the orbital position of GEOS 3, significant improvement has been obtained with new geopotential solutions, Goddard Earth Model (GEM) 9 and 10. The GEM 9 and 10 solutions for the potential coefficients and station coordinates are presented along with a discussion of the new techniques employed. Also presented and discussed are solutions for three fundamental geodetic reference parameters, viz. the mean radius of the earth, the gravitational constant, and mean equatorial gravity. Evaluation of the gravity field is examined together with evaluation of GEM 9 and 10 for orbit determination accuracy. The major objectives of GEM 9 and 10 are achieved. GEOS 3 orbital accuracies from these models are about 1 m in their radial components for 5-day arc lengths. Both models yield significantly improved results over GEM solutions when compared to surface gravimetry, Skylab and GEOS 3 altimetry, and highly accurate BE-C (Beacon Explorer-C) laser ranges. The new values of the parameters discussed are given.

Z-phase in 9-12% Cr Steels

DEFF Research Database (Denmark)

Danielsen, Hilmar; Hald, John

2004-01-01

The complex nitride Z-phase, Cr(V,Nb)N, has recently been identified as a major cause for premature breakdown in creep strength of a number of new 9-12%Cr martensitic steels. A thermodynamic model of the Z-phase has been created based on the Thermo-Calc software. The model predicts the Z-phase to......The complex nitride Z-phase, Cr(V,Nb)N, has recently been identified as a major cause for premature breakdown in creep strength of a number of new 9-12%Cr martensitic steels. A thermodynamic model of the Z-phase has been created based on the Thermo-Calc software. The model predicts the Z......-phase to be stable in all of the new 9-12%Cr martensitic steels. This has generally been confirmed by the performed experiments. Z-phase precipitation seems to be a kinetic problem, and drivning force calculations using Thermo-Calc with the developed model have been used to predict steel compositions, which...

Structural and functional cardiac adaptations to a 10-week school-based football intervention for 9-10-year-old children

DEFF Research Database (Denmark)

Krustrup, Peter; Hansen, Peter Riis; Nielsen, Claus Malta

2014-01-01

-randomized into a control group that maintained their usual activities (CON; two classes, n = 51, 21 boys and 30 girls) and a football training group that performed an additional 3 × 40 min of small-sided football training per week (FT; two classes, n = 46, 23 boys and 23 girls). No baseline differences were observed......The present study investigated the cardiac effects of a 10-week football training intervention for school children aged 9-10 years using comprehensive transthoracic echocardiography as a part of a larger ongoing study. A total of 97 pupils from four school classes were cluster...

Overview of 9Cr steels properties for structural application in sodium fast reactors

International Nuclear Information System (INIS)

Cabet, Celine; Courouau, Jean-Louis; Dalle, France; Desgranges, Clara; Forest, Laurent; Martinelli, Laure; Sauzay, Maxime

2015-01-01

A research and development programme has been launched by CEA, EDF and AREVA for the choice and qualification of material for sodium fast reactor (SFR) structural components. The requirements on steam generator (SG) are demanding, with operating temperatures ranging from 240 deg. C to 530 deg. C in water/steam and in sodium for an extended design life of several decades. The selection of the SG materials is based on many characteristics: fabrication, welding, thermal properties, mechanical strength at low and high temperature, environmental resistance. 9%Cr steels which are relevant candidate alloys for different designs of SGs have been extensively studied in the past decade. The objective of this paper is to review some advances made at CEA on determining properties of the X10CrMoVNb9-1 steel (hereafter named 'grade 91'): welding, modelling of cyclic softening, modelling of long-term creep, compatibility with liquid sodium, corrosion in steam. (authors)

10 CFR 25.9 - Communications.

Science.gov (United States)

2010-01-01

... Director, Division of Facilities and Security, Mail Stop T7-D57, and sent either by mail to the U.S... Rockville Pike, Rockville, Maryland; or, where practicable, by electronic submission, for example, Electronic Information Exchange, or CD-ROM. Electronic submissions must be made in a manner that enables the...

submitter CXCL$_{10}$ Is a Circulating Inflammatory Marker in Patients with Advanced Heart Failure: a Pilot Study

CERN Document Server

Altara, Raffaele; Hessel, Marleen H; Gu, Yumei; van Vark, Laura C; Akkerhuis, K Martijn; Staessen, Jan A; Struijker-Boudier, Harry A J; Booz, George W; Blankesteijn, W Matthijs

2016-01-01

Chemokines are involved in the remodeling of the heart; however, their significance as biomarkers in heart failure is unknown. We observed that circulating CXCR3 receptor chemokines CXCL9 and CXCL10 in a rat model of heart failure were increased 1 week after myocardial infarction. CXCL10 was also increased in both remote and infarcted regions of the heart and remained elevated at 16 weeks; CXCL9 was elevated in the remote area at 1 week. In humans, hierarchical clustering and principal component analysis revealed that circulating CXCL10, MIP-1α, and CD40 ligand were the best indicators for differentiating healthy and heart failure subjects. Serum CXCL10 levels were increased in patients with symptomatic heart failure as indexed by NYHA classification II through IV. The presence of CXCL10, MIP-1α, and CD40 ligand appears to be dominant in patients with advanced heart failure. These findings identify a distinct profile of inflammatory mediators in heart failure patients

Long term properties and microstructural evolution of 18Cr-10Ni-3Cu-Ti-Nb austenitic stainless steel for boiler tube application

Energy Technology Data Exchange (ETDEWEB)

Minami, Y.; Fukui, T.; Ono, T. [TenarisNKK Tubes, Kawasaki, Kanagawa (Japan); Caminada, S. [TenarisDalmine, Dalmine, BG (Italy)

2010-07-01

The allowable tensile stress of 0.1C-18Cr-10Ni-3Cu-Ti-Nb steel (TEMPALOY AA-1; ASME C.C. 2512) is more than 30% higher compared with that of ASME SA-213 Grade TP347H in the temperature range 600-700 C. This high creep rupture strength is obtained by the precipitation of MC and M{sub 23}C{sub 6} carbides, and Cu-rich phase. Long term creep rupture tests over 10{sup 5}h enabled to verify the superior creep rupture strength of this steel. The investigation of microstructural evolution on the creep ruptured and aged specimens has shown the high structural stability of this material. Hardness and impact properties after high temperature aging reveal similar performance as conventional 18-8 stainless steels. Excellent steam oxidation resistance can be achieved by a shot-blasting method. The scale thickness of shot-blasted tube after 1000h at 750 C is below a few micron meters. These results have revealed that the mechanical properties and environmental resistance of this steel enable the use of TEMPALOY AA-1 in the latest generation of advanced USC boiler. (orig.)

Structural and spectroscopic studies of 2,9-dimethyl-1,10 ...

African Journals Online (AJOL)

The crystal structures of the pronated ligand, 2,9-dimethyl-1,10-phenanthrolinium (DPH) cation with selected counter anions (chloride (1), triflate (2), and gold dicyanide (3)) are reported. The role of a hydrogen bond interaction in influencing the solid state p-p stacking found in all three compounds has been investigated.

THE J = 1-0 TRANSITIONS OF 12CH+, 13CH+, AND 12CD+

International Nuclear Information System (INIS)

Amano, T.

2010-01-01

A new set of laboratory experimental frequencies for the J = 1-0 rotational transition of 12 CH + , 13 CH + , and 12 CD + are obtained by using a liquid nitrogen cooled extended negative glow discharge in a gas mixture of CH 4 and He. These frequencies are found to be significantly different from those reported previously. The unexpectedly large Zeeman effect and the spin-rotation hyperfine interaction for a 1 Σ molecule are observed. The Zeeman effect and the hyperfine interaction appear to be distinctively different for each isotopic species. Theoretical considerations reveal the isotopic dependence of the magnitudes of these effects, and they also provide strong evidence for the identifications.

High PD-L1/CD86 MFI ratio and IL-10 secretion characterize human regulatory dendritic cells generated for clinical testing in organ transplantation.

Science.gov (United States)

Zahorchak, Alan F; Macedo, Camila; Hamm, David E; Butterfield, Lisa H; Metes, Diana M; Thomson, Angus W

2018-01-01

Human regulatory dendritic cells (DCreg) were generated from CD14 immunobead-purified or elutriated monocytes in the presence of vitamin D3 and IL-10. They exhibited similar, low levels of costimulatory CD80 and CD86, but comparatively high levels of co-inhibitory programed death ligand-1 (PD-L1) and IL-10 production compared to control immature DC (iDC). Following Toll-like receptor 4 ligation, unlike control iDC, DCreg resisted phenotypic and functional maturation and further upregulated PD-L1:CD86 expression. Whereas LPS-stimulated control iDC (mature DC; matDC) secreted pro-inflammatory tumor necrosis factor but no IL-10, the converse was observed for LPS-stimulated DCreg. DCreg weakly stimulated naïve and memory allogeneic CD4 + and CD8 + T cell proliferation and IFNγ, IL-17A and perforin/granzyme B production in MLR. Their stimulatory function was enhanced however, by blocking PD-1 ligation. High-throughput T cell receptor (TCR) sequencing revealed that, among circulating T cell subsets, memory CD8 + T cells contained the most alloreactive TCR clonotypes and that, while matDC expanded these alloreactive memory CD8 TCR clonotypes, DCreg induced more attenuated responses. These findings demonstrate the feasibility of generating highly-purified GMP-grade DCreg for systemic infusion, their influence on the alloreactive T cell response, and a key mechanistic role of the PD1 pathway. Copyright © 2017 Elsevier Inc. All rights reserved.

Features of argon-arc welding of aluminium alloy AD1 to stainless steel 12Kh18N10T

International Nuclear Information System (INIS)

Sadov, I.I.

1982-01-01

Welding of pipes made of the 12Kh18N10T stainless steel and the AD1 aluminium alloy is proposed to perform using one-sided aluminizing. It is recommended to use shields in order to protect internal and external surfaces of pipes, aluminizing of which is impossible. It is shown that developed technological process for welded joints made of aluminium and stainless steel for cryogenic apparatus permits to create light-duty cryostat assembly using aluminium alloys instead of copper alloys, to increase reliability of apparatus (usage of welded joints instead of soldered ones), and to improve labour conditions

Creep strength and microstructural evolution of 9-12% Cr heat resistant steels during creep exposure at 600 C and 650 C

Energy Technology Data Exchange (ETDEWEB)

Mendez Martin, Francisca [Graz Univ. of Technology (Austria). Inst. for Materials Science and Welding; Panait, Clara Gabriela [MINES ParisTech, UMR CNRS, Evry (France). Centre des Materiaux; V et M France CEV, Aulnoye-Aymeries (France); Bendick, Walter [Salzgitter Mannesmann Forschung GmbH (SZMF), Duisburg (DE)] (and others)

2010-07-01

9-12% Cr heat resistant steels are used for applications at high temperatures and pressures in steam power plants. 12% Cr steels show higher creep strength and higher corrosion resistance compared to 9% Cr steels for short term creep exposure. However, the higher creep strength of 12 %Cr steels drops increasingly after 10,000-20,000 h of creep. This is probably due to a microstructural instability such as the precipitation of new phases (e.g. Laves phases and Z-phases), the growth of the precipitates and the recovery of the matrix. 9% Cr and 12% Cr tempered martensitic steels that have been creep tested for times up to 50,000 h at 600 C and 650 C were investigated using Transmission Electron Microscopy (TEM) on extractive replicas and thin foils together with Backscatter Scanning Electron Microscopy (BSE-SEM) to better understand the different creep behaviour of the two different steels. A significant precipitation of Laves phase and low amounts of Z-phase was observed in the 9% Cr steels after long-term creep exposure. The size distribution of Laves phases was measured by image analysis of SEM-BSE images. In the 12% Cr steel two new phases were identified, Laves phase and Z-phase after almost 30,000 h of creep test. The quantification of the different precipitated phases was studied. (orig.)

CXC chemokine receptor 4 expression and stromal cell-derived factor-1alpha-induced chemotaxis in CD4+ T lymphocytes are regulated by interleukin-4 and interleukin-10

DEFF Research Database (Denmark)

Jinquan, T; Quan, S; Jacobi, H H

2000-01-01

-10. IL-4 and IL-10 up- or down-regulated CXCR4 mRNA expression in CD4+ T lymphocytes, respectively, as detected by real-time quantitative reverse transcription-polymerase chain reaction (RT-PCR). Scatchard analysis revealed a type of CXCR4 with affinity (Kd approximately 6.3 nM), and approximately 70....... The regulation of CXCR4 expression in CD4+ T lymphocytes by IL-4 and IL-10 could be blocked by a selective inhibitor of protein kinase (staurosporine) or by a selective inhibitor of cAMP- and cGMP-dependent protein kinase (H-8), indicating that these cytokines regulate CXCR4 on CD4+ T lymphocytes via both c......AMP and cGMP signalling pathways. The fact that cyclosporin A or ionomycin were able to independently change the CXCR4 expression and block the effects of IL-4 and IL-10 on CXCR4 expression implied that the capacity of IL-4 and IL-10 to regulate CXCR4 on CD4+ T lymphocytes is not linked to calcium...

10Be and 9Be in South Atlantic DSDP Site 519: Relation to geomagnetic reversals and to sediment composition

International Nuclear Information System (INIS)

Henken-Mellies, W.U.; Hsue, K.J.; Bonani, G.; Hofmann, H.J.; Woelfli, W.; Beer, J.; Heller, F.; Shen, C.; Suter, M.

1990-01-01

A high-resolution 10 Be profile has been measured on DSDP Site 519 (central South Atlantic) in order to search for changes in the flux of 10 Be into a pelagic sediment during geomagnetic reversals as compared with times of constant magnetic polarity. The decay corrected 10 Be concentrations range from 1 to 9x10 8 at/g. The average 10 Be flux rate is 5x10 8 [at cm -2 kyr -1 ]. 9 Be and CaCO 3 were measured on the same samples. The 10 Be vs. depth curve is overall similar to the 9 Be vs. depth curve, while the CaCO 3 vs. depth curve anticorrelates the beryllium isotope curves closely, implying that Be is carried mainly by the non-CaCO 3 phases of the sediment. The positive correlation between 10 Be along with the fact that the average 10 Be/ 9 Be ratio of 5.5x10 -8 is within the range of 10 Be/ 9 Be ratios reported for deep ocean water leads us to conclude (1) that the beryllium isotopes come close to an equilibrium in the open ocean, and (2) that the 10 Be/ 9 Be in deep sea sediments with a low detrital component monitors the 10 Be/ 9 Be of deep ocean water trough time. Relative increases of the 10 Be/ 9 Be ratio are observed in the vicinity of the geomagnetic reversals, but the relationship between reversals and higher 10 Be/ 9 Be remains doubtful. Other mechanisms which could alter the 10 Be/ 9 Be ratio are discussed (input of 10 Be by melting of glacial ice; changing input of 9 Be due to changes in continental erosion; changing deep ocean circulation; changing scavenging activity at ocean margins), but as yet no conclusive explanation for the observed behavior of the beryllium isotopes can be given. (orig.)

Gravity model improvement using GEOS-3 (GEM 9 and 10)

Science.gov (United States)

Lerch, F. J.; Klosko, S. M.; Laubscher, R. E.; Wagner, C. A.

1977-01-01

The use of collocation permitted GEM 9 to be a larger field than previous derived satellite models, GEM 9 having harmonics complete to 20 x 20 with selected higher degree terms. The satellite data set has approximately 840,000 observations, of which 200,000 are laser ranges taken on 9 satellites equipped with retroreflectors. GEM 10 is complete to 22 x 22 with selected higher degree terms out to degree and order 30 amounting to a total of 592 coefficients. Comparisons with surface gravity and altimeter data indicate a substantial improvement in GEM 9 over previous satellite solutions; GEM 9 is in even closer agreement with surface data than the previously published GEM 6 solution which contained surface gravity. In particular the free air gravity anomalies calculated from GEM 9 and a surface gravity solution are in excellent agreement for the high degree terms.

Effect of Welding Processes on the Microstructure, Mechanical Properties and Residual Stresses of Plain 9Cr-1Mo Steel Weld Joints

Science.gov (United States)

Nagaraju, S.; Vasantharaja, P.; Brahadees, G.; Vasudevan, M.; Mahadevan, S.

2017-12-01

9Cr-1Mo steel designated as P9 is widely used in the construction of power plants and high-temperature applications. It is chosen for fabricating hexcan fuel subassembly wrapper components of fast breeder reactors. Arc welding processes are generally used for fabricating 9Cr-1Mo steel weld joints. A-TIG welding process is increasingly being adopted by the industries. In the present study, shielded metal arc (SMA), tungsten inert gas (TIG) and A-TIG welding processes are used for fabricating the 9Cr-1Mo steel weld joints of 10 mm thickness. Effect of the above welding processes on the microstructure evolution, mechanical properties and residual stresses of the weld joints has been studied in detail. All the three weld joints exhibited comparable strength and ductility values. 9Cr-1Mo steel weld joint fabricated by SMAW process exhibited lower impact toughness values caused by coarser grain size and inclusions. 9Cr-1Mo steel weld joint fabricated by TIG welding exhibited higher toughness due to finer grain size, while the weld joint fabricated by A-TIG welding process exhibited adequate toughness values. SMA steel weld joint exhibited compressive residual stresses in the weld metal and HAZ, while TIG and A-TIG weld joint exhibited tensile residual stresses in the weld metal and HAZ.

Interplay between EZH2 and G9a Regulates CXCL10 Gene Repression in Idiopathic Pulmonary Fibrosis.

Science.gov (United States)

Coward, William R; Brand, Oliver J; Pasini, Alice; Jenkins, Gisli; Knox, Alan J; Pang, Linhua

2018-04-01

Selective repression of the antifibrotic gene CXCL10 contributes to tissue remodeling in idiopathic pulmonary fibrosis (IPF). We have previously reported that histone deacetylation and histone H3 lysine 9 (H3K9) methylation are involved in CXCL10 repression. In this study, we explored the role of H3K27 methylation and the interplay between the two histone lysine methyltransferases enhancer of zest homolog 2 (EZH2) and G9a in CXCL10 repression in IPF. By applying chromatin immunoprecipitation, Re-ChIP, and proximity ligation assays, we demonstrated that, like G9a-mediated H3K9 methylation, EZH2-mediated histone H3 lysine 27 trimethylation (H3K27me3) was significantly enriched at the CXCL10 promoter in fibroblasts from IPF lungs (F-IPF) compared with fibroblasts from nonfibrotic lungs, and we also found that EZH2 and G9a physically interacted with each other. EZH2 knockdown reduced not only EZH2 and H3K27me3 but also G9a and H3K9me3, and G9a knockdown reduced not only G9 and H3K9me3 but also EZH2 and H3K27me3. Depletion and inhibition of EZH2 and G9a also reversed histone deacetylation and restored CXCL10 expression in F-IPF. Furthermore, treatment of fibroblasts from nonfibrotic lungs with the profibrotic cytokine transforming growth factor-β1 increased EZH2, G9a, H3K27me3, H3K9me3, and histone deacetylation at the CXCL10 promoter, similar to that observed in F-IPF, which was correlated with CXCL10 repression and was prevented by EZH2 and G9a knockdown. These findings suggest that a novel and functionally interdependent interplay between EZH2 and G9a regulates histone methylation-mediated epigenetic repression of the antifibrotic CXCL10 gene in IPF. This interdependent interplay may prove to be a target for epigenetic intervention to restore the expression of CXCL10 and other antifibrotic genes in IPF.

Variation of martensite lath width and precipitate size during creep deformation in a 10Cr-Mo steel

International Nuclear Information System (INIS)

Kim, S. H.; Song, B. Z.; Lu, W. S.

2001-01-01

The relationship between creep deformation and microstructural changes in martensitic 10Cr-MoW steel has been studied. Transmission electron microscopy and image analyser were used to determine the variation of precipitates and martensite lath width size during creep deformation and aging. As precipitates are coarsened during creep deformation, dislocations become easy to move and the recovery proceeds rapidly. This leads to the growth of lath width. The average size of precipitates was linearly increased with creep time. On the other hand the growth rate of lath width is constant until tertiary creep, but the growth of lath width is accelerated during tertiary creep. It has been concluded that the growth behavior of lath width are consistent with creep deformation. Because the growth of lath width is controlled by the coarsening of precipitates it is important to form more stable precipitates in creep condition for improvement of creep properties of martensitie steel. Microstructure of martensitic steel is thermally very stable, so the size of precipitates and martensite lath width are hardly changed during aging

Influence of Z-phase on long-term creep stability of martensitic 9-12%Cr steels

Energy Technology Data Exchange (ETDEWEB)

Hald, J. [DONG Energy (Denmark)]|[Vattenfall Europe AG, Berlin (Germany)]|[DTU Mechanical Engineering (Denmark); Danielsen, H.K. [DTU Mechanical Engineering (Denmark)

2008-07-01

The long-term creep strength of the new generation of martensitic creep resistant 9- 12% Cr steels since the well-known steel Grade 91 relies strongly on particle strengthening by fine MN nitrides based on V and Nb. During long-term hightemperature exposures the MN nitrides may be replaced by the thermodynamically more stable Z-phases (Cr(V,Nb)N) causing a breakdown in creep strength. Cr contents above 10.5% strongly accelerate Z-phase precipitation, which explains the lack of success for all attempts to develop martensitic creep resistant steels with high Cr content for oxidation protection. The Z-phase nucleation process by Cr-diffusion into pre-existing MN nitrides is rate controlling for the Z-phase transformation. More work is needed before effects of chemical composition on the nucleation process can be reliably modeled. Careful control of the Z-phase precipitation process has led to the design of experimental 12%Cr martensitic steels strengthened by Z-phase. Such steels may again enable the combination of high strength and oxidation resistance in the same alloy. This opens a new pathway for further alloy development of the heat resistant martensitic steels. (orig.)

Behaviour of Z phase in 9–12%Cr steels

DEFF Research Database (Denmark)

Danielsen, Hilmar Kjartansson; Hald, John

2006-01-01

The literature on the behaviour of modified Z phase Cr(V,Nb)N in creep resistant martensitic 9–12%Cr steels is briefly reviewed. Ten different 9–12%Cr steels were investigated after prolonged exposure at 600–660uC; the modified Z phase was found in all of them. In steels with high Cr content (11......–12%), Z phase precipitates much faster than in 9%Cr steels. Precipitation of Z phase is associated with dissolution of MX carbonitrides, and causes a breakdown in long term creep strength in 9–12%Cr steels. High Cr steels show creep instabilities accompanied with Z phase precipitation, whereas low Cr...... steels show good long term creep stability. A niobium free CrVN variant of the modified Z phase was observed for the first time during the course of this work. The solution temperature of the Cr(V,Nb)N and CrVN modified Z phases was found to be close to 800uC for 11–12%Cr steels, much lower than the 1200...

Plasmodium falciparum-mediated induction of human CD25Foxp3 CD4 T cells is independent of direct TCR stimulation and requires IL-2, IL-10 and TGFbeta.

Directory of Open Access Journals (Sweden)

Anja Scholzen

2009-08-01

Full Text Available CD4(+CD25(+Foxp3(+ regulatory T cells (Tregs regulate disease-associated immunity and excessive inflammatory responses, and numbers of CD4(+CD25(+Foxp3(+ Tregs are increased during malaria infection. The mechanisms governing their generation, however, remain to be elucidated. In this study we investigated the role of commonly accepted factors for Foxp3 induction, TCR stimulation and cytokines such as IL-2, TGFbeta and IL-10, in the generation of human CD4(+CD25(+Foxp3(+ T cells by the malaria parasite Plasmodium falciparum. Using a co-culture system of malaria-infected red blood cells (iRBCs and peripheral blood mononuclear cells from healthy individuals, we found that two populations of Foxp3(hi and Foxp3(int CD4(+CD25(hi T cells with a typical Treg phenotype (CTLA-4(+, CD127(low, CD39(+, ICOS(+, TNFRII(+ were induced. Pro-inflammatory cytokine production was confined to the Foxp3(int subset (IFNgamma, IL-4 and IL-17 and inversely correlated with high relative levels of Foxp3(hi cells, consistent with Foxp3(hi CD4 T cell-mediated inhibition of parasite-induced effector cytokine T cell responses. Both Foxp3(hi and Foxp3(int cells were derived primarily from proliferating CD4(+CD25(- T cells with a further significant contribution from CD25(+Foxp3(+ natural Treg cells to the generation of the Foxp3(hi subset. Generation of Foxp3(hi, but not Foxp3(int, cells specifically required TGFbeta1 and IL-10. Add-back experiments showed that monocytes expressing increased levels of co-stimulatory molecules were sufficient for iRBC-mediated induction of Foxp3 in CD4 T cells. Foxp3 induction was driven by IL-2 from CD4 T cells stimulated in an MHC class II-dependent manner. However, transwell separation experiments showed that direct contact of monocytes with the cells that acquire Foxp3 expression was not required. This novel TCR-independent and therefore antigen-non specific mechanism for by-stander CD4(+CD25(hiFoxp3(+ cell induction is likely to reflect a

Analysis of longitudinal momentum distribution of 10Be in 9Be(11Be, 10Be)X reaction

International Nuclear Information System (INIS)

Singh, Monika; Kharab, Rajesh; Singh, Ram Mehar

2013-01-01

We have analyzed the longitudinal momentum distribution of 10 Be fragment coming from one neutron stripping from 11 Be on 9 Be target at 60AMeV beam energy within the framework of zero and first order eikonal approximation. It has been found that the inclusion of first order correction term in the eikonal approximation results in a substantial improvement in the matching between the predicted and experimental results especially in tail region of the spectrum. (author)

Microstructural characterization of 5-9% chromium reduced-activation steels

International Nuclear Information System (INIS)

Jayaram, R.; Klueh, R.L.

1997-01-01

The microstructures of a 9Cr-2W-0.25-0.1C (9Cr-2WV), a 9Cr-2W-0.25V-0.07Ta-0.1C (9Cr-2WVTa), a 7Cr-2W-0.25V-0.07Ta-0.1C (7Cr-2WVTa), and a 5Cr-2W-0.25V-0.07Ta-0.1C (5Cr-2WVTa) steel (all compositions are in weight percent) have been characterized by Analytical Electron Microscopy (AEM) and Atom Probe Field Ion Microscopy (APFIM). The matrix in all four reduced-activation steels was 100% martensite. In the two 9Cr steels, the stable precipitates were blocky M 23 C 6 and small spherical MC. The two lower-chromium steels contained blocky M 7 C 3 and small needle-shaped carbonitrides in addition to M 23 C 6 . AEM and APFIM analysis revealed that in the steels containing tantalum, the majority of the tantalum was in solid solution. The experimental observations were in good agreement with phases and compositions predicted by phase equilibria calculations

A mouse model of familial ALS has increased CNS levels of endogenous ubiquinol9/10 and does not benefit from exogenous administration of ubiquinol10.

Directory of Open Access Journals (Sweden)

Jacopo Lucchetti

Full Text Available Oxidative stress and mitochondrial impairment are the main pathogenic mechanisms of Amyotrophic Lateral Sclerosis (ALS, a severe neurodegenerative disease still lacking of effective therapy. Recently, the coenzyme-Q (CoQ complex, a key component of mitochondrial function and redox-state modulator, has raised interest for ALS treatment. However, while the oxidized form ubiquinone10 was ineffective in ALS patients and modestly effective in mouse models of ALS, no evidence was reported on the effect of the reduced form ubiquinol10, which has better bioavailability and antioxidant properties. In this study we compared the effects of ubiquinone10 and a new stabilized formulation of ubiquinol10 on the disease course of SOD1(G93A transgenic mice, an experimental model of fALS. Chronic treatments (800 mg/kg/day orally started from the onset of disease until death, to mimic the clinical trials that only include patients with definite ALS symptoms. Although the plasma levels of CoQ10 were significantly increased by both treatments (from <0.20 to 3.0-3.4 µg/mL, no effect was found on the disease progression and survival of SOD1(G93A mice. The levels of CoQ10 in the brain and spinal cord of ubiquinone10- or ubiquinol10-treated mice were only slightly higher (≤10% than the endogenous levels in vehicle-treated mice, indicating poor CNS availability after oral dosing and possibly explaining the lack of pharmacological effects. To further examine this issue, we measured the oxidized and reduced forms of CoQ9/10 in the plasma, brain and spinal cord of symptomatic SOD1(G93A mice, in comparison with age-matched SOD1(WT. Levels of ubiquinol9/10, but not ubiquinone9/10, were significantly higher in the CNS, but not in plasma, of SOD1(G93A mice, suggesting that CoQ redox system might participate in the mechanisms trying to counteract the pathology progression. Therefore, the very low increases of CoQ10 induced by oral treatments in CNS might be not sufficient to

Study of the potential use of isotopic compositions of Hg, Cd and Zn to constrain their origins in PM10. Final report

International Nuclear Information System (INIS)

2009-01-01

As air pollution by dust remains an important issue because of its impact on human health and ecosystems, and as dusts having a diameter smaller than 10 micrometers (PM10) have an actual impact on human health, this study aims at using mercury, zinc and cadmium isotopes in order to constrain their respective origins in the particle phase, in Paris atmosphere. Thus, the authors aim at developing a new isotopic tracing tool. After some generalities on the concerned isotopes, a description of analytical methods, a presentation of the different sampling sources, the authors discuss the obtained results for samples coming from particle sources (engines, buses, incinerators, power plants, collective boiler rooms) or from the ambient air (PM10 concentration in the Parisian air, Cd, Hg and Zn concentrations, Cd, Hg and Zn isotopes

Rapamycin combined with anti-CD45RB mAb and IL-10 or with G-CSF induces tolerance in a stringent mouse model of islet transplantation.

Directory of Open Access Journals (Sweden)

Nicola Gagliani

Full Text Available BACKGROUND: A large pool of preexisting alloreactive effector T cells can cause allogeneic graft rejection following transplantation. However, it is possible to induce transplant tolerance by altering the balance between effector and regulatory T (Treg cells. Among the various Treg-cell types, Foxp3(+Treg and IL-10-producing T regulatory type 1 (Tr1 cells have frequently been associated with tolerance following transplantation in both mice and humans. Previously, we demonstrated that rapamycin+IL-10 promotes Tr1-cell-associated tolerance in Balb/c mice transplanted with C57BL/6 pancreatic islets. However, this same treatment was unsuccessful in C57BL/6 mice transplanted with Balb/c islets (classified as a stringent transplant model. We accordingly designed a protocol that would be effective in the latter transplant model by simultaneously depleting effector T cells and fostering production of Treg cells. We additionally developed and tested a clinically translatable protocol that used no depleting agent. METHODOLOGY/PRINCIPAL FINDINGS: Diabetic C57BL/6 mice were transplanted with Balb/c pancreatic islets. Recipient mice transiently treated with anti-CD45RB mAb+rapamycin+IL-10 developed antigen-specific tolerance. During treatment, Foxp3(+Treg cells were momentarily enriched in the blood, followed by accumulation in the graft and draining lymph node, whereas CD4(+IL-10(+IL-4(- T (i.e., Tr1 cells localized in the spleen. In long-term tolerant mice, only CD4(+IL-10(+IL-4(- T cells remained enriched in the spleen and IL-10 was key in the maintenance of tolerance. Alternatively, recipient mice were treated with two compounds routinely used in the clinic (namely, rapamycin and G-CSF; this drug combination promoted tolerance associated with CD4(+IL-10(+IL-4(- T cells. CONCLUSIONS/SIGNIFICANCE: The anti-CD45RB mAb+rapamycin+IL-10 combined protocol promotes a state of tolerance that is IL-10 dependent. Moreover, the combination of rapamycin+G-CSF induces

Random cyclic constitutive models of 0Cr18Ni10Ti pipe steel

International Nuclear Information System (INIS)

Zhao Yongxiang; Yang Bing

2004-01-01

Experimental study is performed on the random cyclic constitutive relations of a new pipe stainless steel, 0Cr18Ni10Ti, by an incremental strain-controlled fatigue test. In the test, it is verified that the random cyclic constitutive relations, like the wide recognized random cyclic strain-life relations, is an intrinsic fatigue phenomenon of engineering materials. Extrapolating the previous work by Zhao et al, probability-based constitutive models are constructed, respectively, on the bases of Ramberg-Osgood equation and its modified form. Scattering regularity and amount of the test data are taken into account. The models consist of the survival probability-strain-life curves, the confidence strain-life curves, and the survival probability-confidence-strain-life curves. Availability and feasibility of the models have been indicated by analysis of the present test data

Study of the unbound nuclei 7,9He and 10Li

International Nuclear Information System (INIS)

Al Falou, H.

2007-07-01

The unbound nuclei 7,9 He and 10 Li have been investigated via the high-energy breakup of beams of neutron-rich nuclei ( 8 He, 11 Be and 14 B). The decay-energy spectra were reconstructed from coincident measurements of the charged fragments ( 6,8 He and 9 Li) with a ΔE-E telescope (CHARISSA) and the neutrons with the DEMON array. A theoretical approach based on the sudden approximation was used to model the reactions populating the unbound final states. The calculated decay-energy spectra were convoluted with the response function of the experimental setup using a simulation developed specifically for the present study and compared with the experimental results. The 10 Li system was produced using an 11 Be beam and the results confirm the continuation of the inversion of the ν1s1/2 and ν0p1/2 levels in the N = 7 isotopic chain. The 9 He system was produced in two different ways with the breakup of 11 Be and 14 B, and was the most exotic system studied here. In this case, a structure was observed at very low decay energy which very probably corresponds to a virtual s state (a s ≅ -2 - 0 fm). This result suggests that the level inversion also occurs in 9 He, but with a much weaker core-neutron interaction than for 10 Li (a s equals -14 ± 2 fm). For the data acquired from the breakup of the 14 B beam, the decay energy spectrum exhibits a resonance around E r equals 1.2 MeV, which most probably corresponds to an excited 1/2 - state in 9 He. The 7 He system was investigated with three different beams ( 8 He, 11 Be and 14 B). No evidence for the existence of the proposed low-lying (E r ∼ 1 MeV) spin-orbit partner (1/2 - ) of the ground state (3/2 - ) could be found. (author)

46 CFR 111.10-9 - Ship's service supply transformers; two required.

Science.gov (United States)

2010-10-01

... ENGINEERING ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Power Supply § 111.10-9 Ship's service supply transformers; two required. If transformers are used to supply the ship's service distribution system required by... system would consist of transformers, overcurrent protection devices, and cables, and would normally be...

Synthesis and Crystal Structures of Luminescent Mononuclear Ni(ii and Cd(ii Complexes with 1,10-phenanthroline

Directory of Open Access Journals (Sweden)

Ecaterina Tocana

2017-12-01

Full Text Available New supramolecular systems of Ni(II and Cd(II with 1,10-phenanthroline constructed by non-covalent interactions have been synthesized and characterized by single-crystal X-ray diffractometry. The smaller nickel(II ion forms a cis complex with outer-sphere perchlorates, while the cadmium(II ion forms a trans complex involving inner-sphere perchlorates. Both compoundsrevealintraligand-basedluminescentproperties.

High - speed steel for precise cased tools

International Nuclear Information System (INIS)

Karwiarz, J.; Mazur, A.

2001-01-01

The test results of high-vanadium high - speed steel (SWV9) for precise casted tools are presented. The face -milling cutters of NFCa80A type have been tested in industrial operating conditions. An average life - time of SWV9 steel tools was 3-10 times longer compare to the conventional high - speed milling cutters. Metallography of SWB9 precise casted steel revealed beneficial for tool properties distribution of primary vanadium carbides in the steel matrix. Presented results should be a good argument for wide application of high - vanadium high - speed steel for precise casted tools. (author)

Human Asymptomatic Epitope Peptide/CXCL10-Based Prime/Pull Vaccine Induces Herpes Simplex Virus-Specific Gamma Interferon-Positive CD107+ CD8+ T Cells That Infiltrate the Cornea and Trigeminal Ganglia of Humanized HLA Transgenic Rabbits and Protect against Ocular Herpes Challenge.

Science.gov (United States)

Khan, Arif A; Srivastava, Ruchi; Vahed, Hawa; Roy, Soumyabrata; Walia, Sager S; Kim, Grace J; Fouladi, Mona A; Yamada, Taikun; Ly, Vincent T; Lam, Cynthia; Lou, Anthony; Nguyen, Vivianna; Boldbaatar, Undariya; Geertsema, Roger; Fraser, Nigel W; BenMohamed, Lbachir

2018-06-13

Herpes simplex virus 1 (HSV-1) is a prevalent human pathogen that infects the cornea causing potentially blinding herpetic disease. A clinical herpes vaccine is still lacking. In the present study, a novel prime/pull vaccine was tested in Human Leukocyte Antigen- (HLA-) transgenic rabbit model of ocular herpes (HLA Tg rabbit). Three asymptomatic (ASYMP) peptide epitopes were selected from the HSV-1 membrane glycoprotein C (UL44 400-408 ), the DNA replication binding helicase (UL9 196-204 ), and the tegument protein (UL25 572-580 ), all preferentially recognized by CD8 + T cells from "naturally protected" HSV-1-seropositive healthy ASYMP individuals (who never had recurrent corneal herpetic disease). HLA Tg rabbits were immunized with a mixture of these three ASYMP CD8 + T cell peptide epitopes (UL44 400-408 , UL9 196-204 and UL25 572-580 ), delivered subcutaneously with CpG 2007 adjuvant (prime). Fifteen days later, half of the rabbits received a topical ocular treatment with a recombinant neurotropic AAV8 vector, expressing the T cell-attracting CXCL10 chemokine (pull). The frequency, function of HSV-specific CD8 + T cells induced by the prime/pull vaccine were assessed in peripheral blood, cornea, and trigeminal ganglia (TG). Compared to peptides alone, the peptides/CXCL10 prime/pull vaccine generated frequent polyfunctional gamma interferon-positive (IFN-γ + ) CD107 + CD8 + T cells that infiltrated both the cornea and TG. CD8 + T cells mobilization into cornea and TG of prime/pull- vaccinated rabbits was associated with a significant reduction in corneal herpes infection and disease following an ocular HSV-1 challenge (McKrae). These findings draw attention to the novel prime/pull vaccine strategy to mobilize anti-viral CD8 + T cells into tissues protecting them against herpes infection and disease. IMPORTANCE There is an urgent need for a vaccine against widespread herpes simplex virus infections. The present study demonstrates that immunization of HLA

Leu-9 (CD 7) positivity in acute leukemias: a marker of T-cell lineage?

Science.gov (United States)

Ben-Ezra, J; Winberg, C D; Wu, A; Rappaport, H

1987-01-01

Monoclonal antibody Leu-9 (CD 7) has been reported to be a sensitive and specific marker for T-cell lineage in leukemic processes, since it is positive in patients whose leukemic cells fail to express other T-cell antigens. To test whether Leu-9 is indeed specific for T-cell leukemias, we examined in detail 10 cases of acute leukemia in which reactions were positive for Leu-9 and negative for other T-cell-associated markers including T-11, Leu-1, T-3, and E-rosettes. Morphologically and cytochemically, 2 of these 10 leukemias were classified as lymphoblastic, 4 as myeloblastic, 2 as monoblastic, 1 as megakaryoblastic, and 1 as undifferentiated. The case of acute megakaryoblastic leukemia is the first reported case to be Leu-9 positive. None of the 10 were TdT positive. Of six cases (two monoblastic, one lymphoblastic, one myeloblastic, one megakaryoblastic, and one undifferentiated) in which we evaluated for DNA gene rearrangements, only one, a peroxidase-positive leukemia, showed a novel band on study of the T-cell-receptor beta-chain gene. We therefore conclude that Leu-9 is not a specific marker to T-cell lineage and that, in the absence of other supporting data, Leu-9 positivity should not be used as the sole basis of classifying an acute leukemia as being T-cell derived.

Microstructural stability of 21-6-9 stainless steel

International Nuclear Information System (INIS)

Krenzer, R.W.; Sanderson, E.C.

1978-01-01

Two experiments were designed to better define parameters for thermomechanical processing of 21-6-9 stainless steel. This steel is one of the nitrogen-strengthened chromium, manganese, and nickel austenitic stainless steels having mechanical properties that can be improved by a combination of plastic deformation and heat treatments. By heat-treating coupons, the time-temperature relationship of the precipitate phase, and the solutionizing, recrystallizing, and stress-relieving temperature ranges in 21-6-9 were established. Secondly, mechanical properties and microstructure as a function of percent deformation and stress-relieving temperature are reported

Mechanical properties of Fe -10Ni -7Mn martensitic steel subjected to severe plastic deformation via cold rolling and wire drawing

Energy Technology Data Exchange (ETDEWEB)

Ghasemi-Nanesa, H; Shirazi, H [School of Metallurgy and Materials Engineering, Faculty of Engineering, University of Tehran, P.O. Box 14395-731 (Iran, Islamic Republic of); Nili-Ahmadabadi, M, E-mail: sut.caster.81710018@gmail.co, E-mail: nili@ut.ac.i [School of Metallurgy and Materials Engineering, Faculty of Engineering, University of Tehran, P.O. Box 14395-731 (Iran, Islamic Republic of) and Center of Excellence for High Performance Materials, University of Tehran, P.O. Box 14395-731, Tehran (Iran, Islamic Republic of)

2010-07-01

Fe-Ni-Mn martensitic steels are one of the major groups of ultra-high strength steels that have good mechanical properties and ductility in as annealed condition but they suffer from severe inter-granular embitterment after aging. In this paper, the effect of heavy shaped cold rolling and wire drawing on the mechanical properties of Fe-Ni-Mn steel was investigated. This process could provide a large strain deformation in this alloy. The total strain was {epsilon} {approx}7. Aging behavior and tensile properties of Fe-10Ni-7Mn were studied after aging at 753 K. The results showed that the ultimate tensile strength and ductility after cold rolling, wire drawing and aging increased up to 2540 MPa and 7.1 %, respectively, while the conventional steels show a premature fracture stress of 830 MPa with about zero ductility after aging.

Mechanical properties of Fe -10Ni -7Mn martensitic steel subjected to severe plastic deformation via cold rolling and wire drawing

Science.gov (United States)

Ghasemi-Nanesa, H.; Nili-Ahmadabadi, M.; Shirazi, H.

2010-07-01

Fe-Ni-Mn martensitic steels are one of the major groups of ultra-high strength steels that have good mechanical properties and ductility in as annealed condition but they suffer from severe inter-granular embitterment after aging. In this paper, the effect of heavy shaped cold rolling and wire drawing on the mechanical properties of Fe-Ni-Mn steel was investigated. This process could provide a large strain deformation in this alloy. The total strain was epsilon ~7. Aging behavior and tensile properties of Fe-10Ni-7Mn were studied after aging at 753 K. The results showed that the ultimate tensile strength and ductility after cold rolling, wire drawing and aging increased up to 2540 MPa and 7.1 %, respectively, while the conventional steels show a premature fracture stress of 830 MPa with about zero ductility after aging.

Effect of cold deformation on latent energy value and high-temperature mechanical properties of 12Cr18Ni10Ti steel

International Nuclear Information System (INIS)

Maksimkin, O.P.; Shiganakov, Sh.B.; Gusev, M.N.

1997-01-01

Energetic and magnetic characteristics and also the high-temperature mechanical properties depending on the preliminary cold deformation of 12Cr18Ni10Ti steel are presented. It is shown that the value of storage energy in the steel has being grown with increase of the deformation. The rate of its growth has been increased after beginning of martensitic γ→α'- transformation when value of comparative storage energy at first decreased and then has been stay practically constant. Level of mechanical properties of the steel at 1073 K has been determined not only by value of cold deformation but and structural reconstruction corresponding to deformations 35-45% and accompanying with α'-phase martensite formation and change of energy accumulating rate. Preliminary cold deformation (40-60 %) does not improve high- temperature plasticity of steel samples implanted by helium. refs. 7, figs. 2

Rumpictuside A: Unusual 9,10-anthraquinone glucoside from Rumex pictus Forssk.

Science.gov (United States)

El-Kashak, Walaa A; Elshamy, Abdelsamed I; Mohamed, Tarik A; El Gendy, Abd El-Nasser G; Saleh, Ibrahim A; Umeyama, Akemi

2017-08-07

A new 8-ionized hydroxylated 9,10-anthraquinone namely, 1-hydroxy-3-methyl-9,10-anthraquinone-6-O-β-D-glucopyranoside-8-olate (Rumpictuside A, 1) along with five known flavonoids, apigenin 7-O-β-D-glucoside (2), vitexin (3), quercetin 3-O-β-D-glucouronide (4), orientin (5), and isorientin (6) were isolated from Rumex pictus. The structures of isolated compounds were identified by the extensive spectroscopic techniques such as, UV, FT-IR, 1D, 2D NMR and HR-FAB-ESI-MS. The ionized hydroxyl group in the new anthraquinone (1) was rarely found for anthraquinone glycosides isolated from natural sources. All the isolated compounds were found inactive against influenza A virus infection. Compounds 2-6 exhibited significant antioxidant activity against DPPH and ABTS + . The alcoholic extract exhibited moderate activity while the new anthraquinone 1 showed the lowest activity against both assays. Copyright © 2017 Elsevier Ltd. All rights reserved.

Synthesis, structure and sensing behavior of a Cd-coordination polymer based on 1,10-phenanthroline and 2-aminoterephthalic acid

Science.gov (United States)

Meng, Xing; Wang, Hai-Feng; Chen, He; Zhou, Zi-Yan; Wang, Hai-Ning

The reaction of 2-aminoterephthalic acid and 1,10-phenanthroline with Cd(NO3)2ṡ4H2O under solvothermal conditions leads to the formation of [Cd(2-aip)(phen)]ṡ0.5C2H5OH ( 1). In the compound, dimetallic cluster [Cd2(COO)4] exists and is linked by 2-aip ligands to stretch into a 2D flat layer. These layers are lined parallel to each other via N-HṡṡṡOCO hydrogen bond interactions, generating a 3D supramolecular architecture. The sensing property has been investigated. The experimental results show that the compound can be used as a luminescent probe to detect Co2+ and organic small molecules acetone.

Hydrogen trapping energy levels and hydrogen diffusion at high and low strain rates (~10{sup 5} s{sup −1} and 10{sup −7} s{sup −1}) in lean duplex stainless steel

Energy Technology Data Exchange (ETDEWEB)

Silverstein, R., E-mail: barrav@post.bgu.ac.il; Eliezer, D.

2016-09-30

Duplex stainless steels (DSS) alloys are high strength steels combined with ductility and excellent resistance to stress corrosion cracking, which makes them attractive for the pressure vessels or underwater pipelines industries. Hydrogen embrittlement (HE) is caused by the action of hydrogen in combination with residual or applied stress and can lead to the mechanical degradation of a material. Dynamic and quasi-static experiments were conducted at room temperature and strain rates of 10{sup 5} s{sup −1} and 10{sup −7} s{sup −1} on gas-phase hydrogen charged DSS. Hydrogen trapping in the various defects and its effect on the mechanical properties are discussed in details. A linear model of Lee and Lee was applied to calculate the trap activation energies. It was found that lower strain rates (~10{sup −7} s{sup −1}) will create less deep hydrogen trapping energies values; ~40% lower than in non-loaded sample. In addition, higher dynamic pressure will create higher trapping energy sites for hydrogen. Based on our experimental studies we developed an analytical model for hydrogen trapping. We have found that the strain rate has a direct influence on both hydrogen diffusion and hydrogen potential trapping sites. During deformation processes created at low strain rates (~10{sup −7} s{sup −1}) hydrogen has enough time to migrate with dislocations from deeper potential trapping sites to lower potential trapping sites.

Microstructural characterization of 5-9% chromium reduced-activation steels

Energy Technology Data Exchange (ETDEWEB)

Jayaram, R. [Univ. of Pittsburgh, PA (United States); Klueh, R.L. [Oak Ridge National Lab., TN (United States)

1997-08-01

The microstructures of a 9Cr-2W-0.25-0.1C (9Cr-2WV), a 9Cr-2W-0.25V-0.07Ta-0.1C (9Cr-2WVTa), a 7Cr-2W-0.25V-0.07Ta-0.1C (7Cr-2WVTa), and a 5Cr-2W-0.25V-0.07Ta-0.1C (5Cr-2WVTa) steel (all compositions are in weight percent) have been characterized by Analytical Electron Microscopy (AEM) and Atom Probe Field Ion Microscopy (APFIM). The matrix in all four reduced-activation steels was 100% martensite. In the two 9Cr steels, the stable precipitates were blocky M{sub 23}C{sub 6} and small spherical MC. The two lower-chromium steels contained blocky M{sub 7}C{sub 3} and small needle-shaped carbonitrides in addition to M{sub 23}C{sub 6}. AEM and APFIM analysis revealed that in the steels containing tantalum, the majority of the tantalum was in solid solution. The experimental observations were in good agreement with phases and compositions predicted by phase equilibria calculations.

Tetraspanin CD9 Limits Mucosal Healing in Experimental Colitis

Directory of Open Access Journals (Sweden)

María Laura Saiz

2017-12-01

Full Text Available Tetraspanins are a family of proteins with four transmembrane domains that associate between themselves and cluster with other partner proteins, conforming a distinct class of membrane domains, the tetraspanin-enriched microdomains (TEMs. These TEMs constitute macromolecular signaling platforms that regulate key processes in several cellular settings controlling signaling thresholds and avidity of receptors. In this study, we investigated the role of CD9, a tetraspanin that regulates major biological processes such as cell migration and immunological responses, in two mouse models of colitis that have been used to study the pathogenesis of inflammatory bowel disease (IBD. Previous in vitro studies revealed an important role in the interaction of leukocytes with inflamed endothelium, but in vivo evidence of the involvement of CD9 in inflammatory diseases is scarce. Here, we studied the role of CD9 in the pathogenesis of colitis in vivo. Colitis was induced by administration of dextran sodium sulfate (DSS, a chemical colitogen that causes epithelial disruption and intestinal inflammation. CD9−/− mice showed less severe colitis than wild-type counterparts upon exposure to DSS (2% solution and enhanced survival in response to a lethal DSS dose (4%. Decreased neutrophil and macrophage cell infiltration was observed in colonic tissue from CD9−/− animals, in accordance with their lower serum levels of TNF-α, IL-6, and other proinflammatory cytokines in the colon. The specific role of CD9 in IBD was further dissected by transfer of CD4+ CD45RBhi naive T cells into the Rag1−/− mouse colitis model. However, no significant differences were observed in these settings between both groups, ruling out a role for CD9 in IBD in the lymphoid compartment. Experiments with bone marrow chimeras revealed that CD9 in the non-hematopoietic compartment is involved in colon injury and limits the proliferation of epithelial cells. Our data indicate that CD9

Association of alkali and alkaline earth metal cations with radical-anions of 9-fluorenone and 9.10-anthraquinone in dimethyl formamide medium

International Nuclear Information System (INIS)

Karpinets, A.P.; Bezuglyj, V.D.; Svetlichnaya, T.M.

1988-01-01

The polarographic method is used to estimate the stability of associates formed in dimethyl formamide by the products of one-electron reduction of 9-fluorenone and 9.10-anthraquinone with cations of alkali and alkali earth metals. It is shown that the strength of 9-fluorenone and 9.10-anthraquinone radical anion associates studied increases with cation charge increase and decrease of its crystallographic radius

Corrosion mechanism of Z3 CN18.10 stainless steel in the presence of nitric acid condensates

International Nuclear Information System (INIS)

Balbaud, Fanny

1998-01-01

In installations handling concentrated boiling nitric acid, a severe intergranular corrosion can sometimes occur in condensation zones constituted of non-sensitized Z3 CN 18.10 stainless steel. Corrosion tests in reactors and in a specific loop, CIRCE, allowed to specify the conditions of occurrence of this type of corrosion and showed the similitude with the corrosion in non-renewed liquid nitric acid: the specific parameters linked to the condensate phase are the high ratio metallic surface area to volume of condensate and the low renewing rate which induce a concentration of oxidation products of the metal and of reduction products of nitric acid. The initiation of the intergranular corrosion is attributed to the increase in the reduction rate of nitric acid by an autocatalytic mechanism which was demonstrated by electrochemical measurements on platinum and on stainless steel. The reduction mechanism involves a charge transfer step where nitrous acid, the electro-active species, is reduced into nitrogen monoxide and a chemical regeneration reaction of nitrous acid. The thermodynamic study led to a representation of the chemical and electrochemical properties of nitric acid. This study allowed also to determine the Gibbs free energy of formation of nitrous acid in solution in concentrated nitric acid at 100 deg. C. The diagram, constructed in coordinates log(P O 2 ) / [-log(P HNO 3 )] or E eXperimental / [-log(P HNO 3 )], shows that the final reduction product of nitric acid depends on the concentration of nitric acid: at 100 deg. C, NO is obtained for concentrations lower than 8 mol.L -1 and NO 2 is obtained for higher concentrations. All these results allowed to propose a corrosion mechanism of Z3 CN 18.10 stainless steel in the presence of nitric acid condensates. [fr

Effect of heat treatment on workability of Cr-Ni-Mo steels

International Nuclear Information System (INIS)

Barcal, J.; Macek, K.

1988-01-01

The workability was studied of the new development generation of hardenable martensite Cr-Ni-Mo steels of the 10-10-2 and 6-11-3 types whose application is envisaged in future in nuclear engineering. Attention is paid to identification of inclusions and the phase analysis ofthe structure with respect to heat treatment and steel type. Face milling was used in the test of workability. In addition, tensile strength and impact bending strength testing was performed. The results showed that steel of the 6-11-3 type in the quenched condition was best workable. However, this steel showed a significant reduction in workability when in the hardened condition. Reduced workability can also be presumed for type 10-10-2 steel in the hardened condition when life is considered. Microstructure changes leading to softening of steel by aging had a favourable effect on workability, especially in steels of the 10-10-2 type. Hardened steels of the 6-11-3 type are recommended to be re-quenched. (Z.M.). 7 figs., 3 tabs., 9 refs

Increased numbers of CD4+ and CD8+ T cells in lesional skin of cats with allergic dermatitis.

Science.gov (United States)

Roosje, P J; van Kooten, P J; Thepen, T; Bihari, I C; Rutten, V P; Koeman, J P; Willemse, T

1998-07-01

The aim of this study was to characterize T cells in the skin of cats with an allergic dermatitis histologically compatible with atopic dermatitis, since T cells play an important role in the pathogenesis of atopic dermatitis in humans. We observed a significantly greater number of T cells in lesional skin of domestic short-haired cats with allergic dermatitis (n = 10; median age 5.8 years) than in the skin of healthy control animals (n = 10; median age 5.0 years). In the skin of the healthy control animals, one or two CD4+ cells and no CD8+ cells were found. A predominant increase of CD4+ T cells and a CD4+/CD8+ ratio (mean +/- SD: 3.9 +/- 2.0) was found in the lesional skin of 10 cats with allergic dermatitis. The CD4+/CD8+ cell ratio in the skin of healthy control animals could not be determined because of the absence of CD8+ cells. The CD4+/CD8+ cell ratio in the peripheral blood of 10 cats with allergic dermatitis (mean +/- SD: 1.9 +/- 0.4) did not differ significantly from that in 10 healthy control animals (2.2 +/- 0.4). The CD4+/CD8+ cell ratio and predominance of CD4+ T cells in the lesional skin of cats with allergic dermatitis is comparable to that found in atopic dermatitis in humans. In addition, the observed increase of CD4+ T cells in the nonlesional skin of cats with allergic dermatitis compared to the skin of healthy cats is similar to what is seen in humans. Cytokines produced by T cells and antigen-specific T cells are important mediators in the inflammatory cascade resulting in atopic dermatitis in humans. This study is a first step to investigate their role in feline allergic dermatitis.

Prevalence of undiagnosed cardiovascular risk factors and 10-year CVD risk in male steel industry workers.

Science.gov (United States)

Gray, Benjamin J; Bracken, Richard M; Turner, Daniel; Morgan, Kerry; Mellalieu, Stephen D; Thomas, Michael; Williams, Sally P; Williams, Meurig; Rice, Sam; Stephens, Jeffrey W

2014-05-01

To assess the prevalence of undiagnosed cardiovascular disease (CVD) in a cohort of male steelworkers in South Wales, UK. Male steel industry workers (n = 221) with no prior diagnosis of CVD or diabetes accepted a CVD risk assessment within the work environment. Demographic, anthropometric, family, and medical histories were all recorded and capillary blood samples obtained. The 10-year CVD risk was predicted using the QRISK2-2012 algorithm. Up to 81.5% of workers were either overweight or obese. More than 20% of workers were found to have diastolic hypertension, high total cholesterol, and/or a total cholesterol/high-density lipoprotein ratio of six or more. Over one quarter of workers assessed had an increased 10-year CVD risk. Despite a physically demanding occupation, risk assessment in the workplace uncovered significant occult factors in CVD risk in a sample of male heavy industry workers.

An efficient synthesis of (7S,10R)-2-bromo-5,6,7,8,9,10-hexahydro-7,10-epiminocyclohepta[b]indole: application in the preparation and structural confirmation of a potent 5-HT6 antagonist

DEFF Research Database (Denmark)

Isherwood, Matthew; Guzzo, Peter R.; Henderson, Alan J.

2012-01-01

precipitation from n-hexane. The absolute stereochemistry of 7a was determined by X-ray crystallography and the structure was confirmed as (7S,10R)-tert-butyl 2-bromo-5,6,7,8,9,10-hexahydro-7,10-epiminocyclohepta[b]indole-11-carboxylate. Removal of the chiral auxiliary under basic conditions afforded...

Microstructure and Nano-Hardness of 10 MeV Cl-Ion Irradiated T91 Steel

International Nuclear Information System (INIS)

Hu Jing; Wang Xianping; Gao Yunxia; Zhuang Zhong; Zhang Tao; Fang Qianfeng; Liu Changsong

2015-01-01

Hardening and elemental segregation of T91 martenstic steel irradiated by 10 MeV Cl ions to doses from 0.06 dpa to 0.83 dpa were investigated with the nanoindentation technique and transmission electron microscopy (TEM). The results demonstrated that the irradiation hardening was closely related with irradiation dose. By increasing the dose, the hardness increased rapidly at first from the initial value of 3.15 GPa before irradiation, and then tended to saturate at a value of 3.58 GPa at the highest dose of 0.83 dpa. Combined with TEM observation, the mechanism of hardening was preliminary attributed to the formation of M(Fe,Cr) 2 3C 6 carbides induced by the high energy Cl-ion irradiation. (paper)

Formed electroslag welded joint from austenitic steel 18/10 CrNi

International Nuclear Information System (INIS)

Jilek, L.; Kusak, L.; Martinak, A.

1987-01-01

The electroslag welded joint from titanium stabilized steel 18/10 CrNi of 150 mm in thickness showed positive results for both nondestructive and destructive testing. Czechoslovak flux VUZ-4F and the optimized welding mode were completely proven. The weldment was subject to deformation by forging with a removal of 20 to 50% and to bending deformation. A 40% to 50% deformation was necessary for breaking the coarse-grain casting structure. The bending deformation resulted in breaking the coarse-grain casting structure in the entire cross-section, it was, however, only acting in a narrow band corresponding to the largest curvature. At the same time, the heat affected zone decayed. Following heat treatment, especially forming, the delta ferrite content in the weld metal decreased, the mechanical properties of the weld metal and the welded joint following welding and heat treatment showed a relatively large scatter. Forming reduced the scatter and improved plastic properties. Machining within 40 and 50% resulted in good echogenicity of the welded joint in ultrasound testing. The welded joint showed equal properties as the base material of the weldment. (author). 15 figs., 2 tabs., 16 refs

The effect of cobalt and molybdenum on the creep strength of low C-18Cr-10Ni steel

International Nuclear Information System (INIS)

Tomono, Yutaka; Ueda, Jitsuhiko

1982-01-01

The improvement of creep strength through the addition of cobalt and molybdenum to low C-18Cr-10Ni steel was studied at a temperature range of between 700 and 800 0 C. Changes in mechanical and physical properties such as lattice parameter and stacking fault energy, related to the additional elements were investigated to estimate the strengthening effect. Dislocation structures corresponding to the various creep stages were observed through a transmission electron microscope to distinguish the solution hardening effect of the added elements from the precipitation hardening effects of carbide. The results obtained are summarized as follows: (1) Addition of cobalt of up to 20% by weight improved the creep strength of austenitic steel. Addition of molybdenum of up to 5% by weight remarkably improved the creep strength of austenitic steel having a cobalt content of 20% by weight. (2) The trend for creep strength to improve with the addition of these elements was closely coincident with increases in lattice parameter and did not necessarily coincide with changes in the stacking fault energy. (author)

Unexpected expansion of tRNA substrate recognition by the yeast m1G9 methyltransferase Trm10.

Science.gov (United States)

Swinehart, William E; Henderson, Jeremy C; Jackman, Jane E

2013-08-01

N-1 Methylation of the nearly invariant purine residue found at position 9 of tRNA is a nucleotide modification found in multiple tRNA species throughout Eukarya and Archaea. First discovered in Saccharomyces cerevisiae, the tRNA methyltransferase Trm10 is a highly conserved protein both necessary and sufficient to catalyze all known instances of m1G9 modification in yeast. Although there are 19 unique tRNA species that contain a G at position 9 in yeast, and whose fully modified sequence is known, only 9 of these tRNA species are modified with m1G9 in wild-type cells. The elements that allow Trm10 to distinguish between structurally similar tRNA species are not known, and sequences that are shared between all substrate or all nonsubstrate tRNAs have not been identified. Here, we demonstrate that the in vitro methylation activity of yeast Trm10 is not sufficient to explain the observed pattern of modification in vivo, as additional tRNA species are substrates for Trm10 m1G9 methyltransferase activity. Similarly, overexpression of Trm10 in yeast yields m1G9 containing tRNA species that are ordinarily unmodified in vivo. Thus, yeast Trm10 has a significantly broader tRNA substrate specificity than is suggested by the observed pattern of modification in wild-type yeast. These results may shed light onto the suggested involvement of Trm10 in other pathways in other organisms, particularly in higher eukaryotes that contain up to three different genes with sequence similarity to the single TRM10 gene in yeast, and where these other enzymes have been implicated in pathways beyond tRNA processing.

Evaluation of liquid metal embrittlement of stainless steel 304 by cadmium and cadmium-aluminum solutions

International Nuclear Information System (INIS)

Iyer, N.C.; Peacock, H.B.; Thomas, J.K.; Begley, J.A.

1994-01-01

The susceptibility of stainless steel 304 (SS304) to liquid metal embrittlement (LME) by cadmium (Cd) and cadmium-aluminum (Cd-Al) solutions was examined as part of a failure evaluation for SS304-clad cadmium reactor safety rods which had been exposed to elevated temperatures. The safety rod test data and destructive examination of the specimens indicated that LME was not the failure mode. The available literature data also suggest that austenitic stainless steels are not particularly susceptible to LME by Cd or Cd-Al solutions. However, the literature data is not conclusive and an experimental study was therefore conducted to examine the susceptibility of SS304 to LME by Cd and Cd-Al solutions. Temperatures from 325 to 600 C and strain rates from 1x10 -6 to 5x10 -5 s -1 were of interest in this evaluation. Tensile tests carried out in molten Cd-Al and Cd solutions over these temperatures and strain rates with both smooth bar and notched specimens showed no evidence of LME. U-bend tests conducted in liquid Cd at 500 and 600 C also showed no evidence of LME. It is concluded that SS304 is not subject to LME by Cd or Cd-Al solutions over the range of temperatures and strain rates of interest. ((orig.))

Rare earth-rich cadmium compounds RE{sub 10}TCd{sub 3} (RE = Y, Tb, Dy, Ho, Er, Tm, Lu; T = Rh, Pd, Ir, Pt) with an ordered Co{sub 2}Al{sub 5}-type structure

Energy Technology Data Exchange (ETDEWEB)

Block, Theresa; Klenner, Steffen; Heletta, Lukas; Poettgen, Rainer [Muenster Univ. (Germany). Inst. fuer Anorganische und Analytische Chemie

2018-04-01

Eighteen new rare earth-rich intermetallic phases RE{sub 10}TCd{sub 3} (RE = Y, Tb, Dy, Ho, Er, Tm, Lu; T = Rh, Pd, Ir, Pt) were obtained by induction melting of the elements in sealed niobium ampoules followed by annealing in muffle furnaces. All samples were characterized by X-ray powder diffraction. The structures of four representatives were refined from single-crystal X-ray diffractometer data: ordered Co{sub 2}Al{sub 5} type, P6{sub 3}/mmc, a = 951.2(1), c = 962.9(2) pm, wR = 0.0460, 595 F{sup 2} values, 20 parameters for Er{sub 10}RhCd{sub 3}; a = 945.17(4), c = 943.33(4), wR = 0.0395, 582 F{sup 2} values, 21 parameters for Lu{sub 9.89}PdCd{sub 3.11}; a = 964.16(6), c = 974.93(6) pm, wR = 0.0463, 614 F{sup 2} values, 21 parameters for Y{sub 10}Ir{sub 1.09}Cd{sub 2.91}; a = 955.33(3), c = 974.56(3) pm, wR = 0.0508, 607 F{sup 2} values, 22 refined parameters for Dy{sub 9.92}IrCd{sub 3.08}. Refinements of the occupancy parameters revealed small homogeneity ranges resulting from RE/Cd, respectively T/Cd mixing. The basic building units of the RE{sub 10}TCd{sub 3} phases are transition metal-centered RE{sub 6} trigonal prisms (TP) that are condensed with double-pairs of empty RE{sub 6} octahedra via common triangular faces. A second type of rods is formed by slightly distorted RE3 rate at Cd{sub 6}RE{sub 6} icosahedra which are condensed via Cd{sub 3} triangular faces. The shortest interatomic distances occur for RE-T, compatible with strong covalent bonding interactions. Temperature dependent magnetic susceptibility measurements were performed for RE{sub 10}RhCd{sub 3} (RE = Dy-Tm, Lu), RE{sub 10}IrCd{sub 3} (RE = Er, Tm, Lu) and RE{sub 10}PtCd{sub 3} (RE = Y, Lu). While Y{sub 10}PtCd{sub 3} and Lu{sub 10}TCd{sub 3} (T = Rh, Ir, Pt) show Pauli paramagnetic behavior, the compounds containing paramagnetic rare earth elements show Curie-Weiss behavior (the experimental magnetic moments indicate stable trivalent RE{sup 3+}) and magnetic ordering at low temperatures

Metal complexes with 1,5- and 1,8-dihydroxy-9,10-anthraquinones: electronic absorption spectra and structure of ligands

International Nuclear Information System (INIS)

Fajn, V.Ya.; Zajtsev, B.E.; Ryabov, M.A.

2004-01-01

By spectrophotometric, quantum-chemical, and correlation methods it is determined that in complexes of metals (Nd, Pr, Sm, Th, UO 2 2+ , V) with 1,5-dihydroxy-9,10-anthraquinone ligand could be in 7 excited states differing not only by ionization degree but primary contribution of tautomeric 9,10-, 1,10-, and 1,5-anthraquinoid structures. On all known complexes with 1,8-dihydroxy-9,10-anthraquinone containing once ionized ligand the last has 1,10-anthraquinoid structure; for complexes containing twofold ionized ligand 9,10-anthraquinoid structure of ligand is the most characteristic. Known complexes are classified in accordance with structure of ligands [ru

Triaqua(1,10-phenanthroline-2,9-dicarboxylatocobalt(II dihydrate

Directory of Open Access Journals (Sweden)

Zi-Fa Shi

2010-04-01

Full Text Available The title compound, [Co(C14H6N2O4(H2O3]·2H2O, has twofold crystallographic symmetry. The CoII atom is in a distorted pentagonal-bipyramidal coordination environment with two N atoms and two O atoms from a tetradentate 1,10-phenanthroline-2,9-dicarboxylate ligand and one O atom from a water molecule forming the pentagonal plane, and two O atoms from two water molecules occupying axial positions. In the crystal, adjacent molecules are linked by O—H...O hydrogen bonds, forming a three-dimensional network.

10 CFR 503.9 - Use of mixtures-general requirement for certain permanent exemptions.

Science.gov (United States)

2010-01-01

... exemptions. 503.9 Section 503.9 Energy DEPARTMENT OF ENERGY (CONTINUED) ALTERNATE FUELS NEW FACILITIES... and petroleum and an alternate fuel for which an exemption under 10 CFR 503.38 (Fuel mixtures) would... substitute mixture, such other alternate fuels as OFE and the petitioner agree are reasonable to petitioner's...

Academic Training Lectures | The Art of Way Finding | 9-10 December

CERN Multimedia

2015-01-01

Please note that the next series of Academic Training Lectures will take place on 9 and 10 December. The lectures will be given by John Huth (Harvard University (US)).   The Art of Way Finding (1/2) on Wednesday, 9 December from 11 a.m. to 12 p.m. https://indico.cern.ch/event/436443/ The Art of Way Finding (2/2) on Thursday, 10 December from 11 a.m. to 12 p.m. http://indico.cern.ch/event/436444/ at CERN, Council Chamber (503-1-001)  Description: In the modern era we've become accustomed to the instantaneous transfer of information filtered by applications that act as a kind of guardian of information. In the realm of finding one’s way, we use GPS and devices that take us from point A to point B without giving it a second thought. Are we slowly losing the cognitive processes that our ancestors had, and at what price? I use the theme of navi...

Maxwell-Stefan based modelling of ion exchange systems containing common species (Cd"2"+, Na"+) and distinct sorbents (ETS-4, ETS-10)

International Nuclear Information System (INIS)

Lito, P. F.; Aniceto, J. P. S.; Silva, C. M.

2015-01-01

Cadmium(II) is a toxic hazardous cation, whose presence in the environment causes great concern because of its bioaccumulation in organisms and bio amplification along food chain. Hence, the removal of cadmium compounds from industrial waters and wastewaters is particularly essential, which requires intensive experimental and modelling studies to deal with the problem. In this work, the ion exchange of Cd"2"+ ions from aqueous solution using microporous titanosilicates (ETS-4 and ETS-10) has been modelled using adapted Maxwell-Stefan equations for the ions transport inside the sorbent particles. The fundamentals of the Maxwell-Stefan equations along with correlations for the convective mass transfer coefficients have been used with advantage to reduce the number of model parameters. In the whole, the model was able to represent successfully the kinetic behaviour of 11 independent and very distinct curves of both studied systems (Cd2"+"/Na"+/ETS-4 and Cd"2"+/Na"+/ ETS-10). The predictive capability of the model has been also shown, since several uptake curves were accurately predicted with parameters fitted previously to different sets of experimental data.

Optimum alloy compositions in reduced-activation martensitic 9Cr steels for fusion reactor

International Nuclear Information System (INIS)

Abe, F.; Noda, T.; Okada, M.

1992-01-01

In order to obtain potential reduced-activation ferritic steels suitable for fusion reactor structures, the effect of alloying elements W and V on the microstructural evolution, toughness, high-temperature creep and irradiation hardening behavior was investigated for simple 9Cr-W and 9Cr-V steels. The creep strength of the 9Cr-W steels increased but their toughness decreased with increasing W concentration. The 9Cr-V steels exhibited poor creep rupture strength, far below that of a conventional 9Cr-1MoVNb steel and poor toughness after aging at 873 K. It was also found that the Δ-ferrite should be avoided, because it degraded both the roughness and high-temperature creep strength. Based on the results on the simple steels, optimized martensitic 9Cr steels were alloy-designed from a standpoint of enough thoughness and high-temperature creep strength. Two kinds of optimized 9Cr steels with low and high levels of W were obtained; 9Cr-1WVTa and 9Cr-3WVTa. These steels indeed exhibited excellent toughness and creep strength, respectively. The 9Cr-1WVTa steel exhibiting an excellent roughness was shown to be the most promising for relatively low-temperature application below 500deg C, where irradiation embrittlement is significant. The 9Cr-3WVTa steel was the most promising for high temperature application above 500deg C from the standpoint of enough high-temperature strength. (orig.)

Effect of agressive medium movement of local corrosion of the steel - 12Kh18N10T

International Nuclear Information System (INIS)

Makartsev, V.V.; Pakhomov, V.S.; Abramova, I.M.

1980-01-01

The effect of agressive medium movement on the formation of pitting corrosion of the 12Kh18N10T stainless steel in the acidic chloride-nitrate solution at room temperature is studied. It is established that the agressive medium movement hinders the formation of pitting corrosion at potentials more negative than +0.4 V and practically does not affect it at more positive potentials. The investigations have been carried out on a disc electrode rotating at a speed from 0 to 2000 rot./min

CD1d knockout mice exhibit aggravated contact hypersensitivity responses due to reduced interleukin-10 production predominantly by regulatory B cells

DEFF Research Database (Denmark)

Fjelbye, Jonas; Antvorskov, Julie C; Buschard, Karsten

2015-01-01

.05) and peritoneal cavity (80.8% decrease; P challenge, which suggests an important regulatory and protective role of CD1d-dependent NKT cells in CHS in our model, at least in part via regulation of IL-10 producing B(regs) ....... knockout (CD1d KO) and wild-type (Wt) mice after contact allergen exposure. For induction of CHS, C57BL/6 CD1d KO mice (n = 6) and C57BL/6 Wt mice (n = 6) were sensitised with 1% (w/v) dinitrochlorobenzene (DNCB) or vehicle for three consecutive days and subsequently challenged with a single dose of 0...

Creep constitutive equation of dual phase 9Cr-ODS steel

International Nuclear Information System (INIS)

Sakasegawa, Hideo; Ukai, Shigeharu; Tamura, Manabu; Ohtsuka, Satoshi; Tanigawa, Hiroyasu; Ogiwara, Hiroyuki; Kohyama, Akira; Fujiwara, Masayuki

2008-01-01

9Cr-ODS (oxide dispersion strengthened) steels developed by JAEA (Japan Atomic Energy Agency) have superior creep properties compared with conventional heat resistant steels. The ODS steels can enormously contribute to practical applications of fast breeder reactors and more attractive fusion reactors. Key issues are developments of material processing procedures for mass production and creep life prediction methods in present R and D. In this study, formulation of creep constitutive equation was performed against the backdrop. The 9Cr-ODS steel displaying an excellent creep property is a dual phase steel. The ODS steel is strengthened by the δ ferrite which has a finer dispersion of oxide particles and shows a higher hardness than the α' martensite. The δ ferrite functions as a reinforcement in the dual phase 9Cr-ODS steel. Its creep behavior is very unique and cannot be interpreted by conventional theories of heat resistant steels. Alternative qualitative model of creep mechanism was formulated at the start of this study using the results of microstructural observations. Based on the alternative creep mechanism model, a novel creep constitutive equation was formulated using the exponential type creep equation extended by a law of mixture

Effect of multiple austenitizing treatments on HT-9 steels

International Nuclear Information System (INIS)

Emigh, R.A.

1985-12-01

The effect of multiple austenitizing treatments on the toughness of an Fe-12Cr-1.0Mo-0.5W-0.3V (HT-9) steel was studied. The resulting microstructures were characterized by their mechanical properties, precipitated carbide distribution, and fracture surface appearance. It was proposed that multiple transformations would refine the martensite structure and improve toughness. Optical and scanning electron microscopic observations revealed that the martensite packet structure was somewhat refined by a second austenite transformation. Transmission electron microscopy studies of carbon extraction replicas showed that this multiple step treatment had eliminated grain boundary carbide films seen in single treated specimens on prior austenite grain boundaries. The 0.2% yield strength, tensile strength, and elongation were relatively unchanged, but the toughness measured by fatigue pre-cracked Charpy impact tests increased for the multiple step specimens

9 CFR 113.10 - Testing of bulk material for export or for further manufacture.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Testing of bulk material for export or for further manufacture. 113.10 Section 113.10 Animals and Animal Products ANIMAL AND PLANT HEALTH... manufacture. When a product is prepared in a licensed establishment for export in large multiple-dose...

Tandem organic light-emitting diodes with KBH4 doped 9,10-bis(3-(pyridin-3-yl)phenyl) anthracene connected to the charge generation layer.

Science.gov (United States)

Duan, Lian; Tsuboi, Taiju; Qiu, Yong; Li, Yanrui; Zhang, Guohui

2012-06-18

Tandem organic light emitting diodes (OLEDs) are ideal for lighting applications due to their low working current density at high brightness. In this work, we have studied an efficient electron transporting layer of KBH(4) doped 9,10-bis(3-(pyridin-3-yl)phenyl)anthracene (DPyPA) which is located adjacent to charge generation layer of MoO(3)/NPB. The excellent transporting property of the DPyPA:KBH(4) layer helps the tandem OLED to achieve a lower voltage than the tandem device with the widely used tris-(8-hydroxyquinoline)aluminum:Li. For the tandem white OLED with a fluorescent blue unit and a phosphorescent yellow unit, we've achieved a high current efficiency of 75 cd/A, which can be further improved to 120 cd/A by attaching a diffuser layer.

2-tert-Butyl-5,6,7,8,9,10-hexahydrocyclohepta[b]indole

Directory of Open Access Journals (Sweden)

Janina Wobbe

2011-09-01

Full Text Available 2-tert-Butyl-5,6,7,8,9,10-hexahydrocyclohepta[b]indole was synthesized by reaction of cycloheptanone and (4-tert-butylphenylhydrazine hydrochloride in the presence of sodium acetate and sulfuric acid in glacial acetic acid via Fischer indole synthesis.

Low-cyclic fatigue behavior of modified 9Cr–1Mo steel at elevated temperature

Energy Technology Data Exchange (ETDEWEB)

Guguloth, Krishna; Sivaprasad, S. [CSIR-National Metallurgical laboratory, Material Science and Technology Division, Jamshedpur 831007 (India); Chakrabarti, D. [Department of Metallurgical and Materials Engineering, Indian Institute of Technology, Kharagpur 721302 (India); Tarafder, S. [CSIR-National Metallurgical laboratory, Material Science and Technology Division, Jamshedpur 831007 (India)

2014-05-01

The low-cycle fatigue behavior of indigenously developed modified 9Cr–1Mo steel has been evaluated using a constant strain rate (1×10{sup −3} s{sup −1}) at ambient temperature (25 °C) and at elevated temperatures (500–600 °C) over the strain amplitudes varying between ±0.7% and ±1.2%. Cyclic stress response showed a gradual softening regime that ended in a stress plateau until complete failure of the specimens. The estimated fatigue life decreased with the increase in test temperature. The effect of temperature on fatigue life was more pronounced at lower strain amplitudes. The cyclic deformation behavior at different temperatures has been analyzed from hysteresis loop and also in view of the changes taking place in dislocation structure and dislocation–precipitation interaction. Evaluation of low-cycle fatigue properties of modified 9Cr–1Mo steel over a range of test temperature can help in designing components for in-core applications in fast breeder reactors and in super heaters for nuclear power plants.

Crystal structure of tetraaquabis(8-chloro-9,10-dioxo-9,10-dihydroanthracene-1-carboxylato-κO1cobalt(II dihydrate

Directory of Open Access Journals (Sweden)

Wen-Juan Cai

2014-10-01

Full Text Available In the title complex, [Co(C15H6ClO42(H2O4]·2H2O, the CoII ion is bound by two carboxylate O atoms of two 5-chloro-9,10-anthraquinone-1-carboxylate anions and four water O atoms in a trans conformation, forming an irregular octahedral coordination geometry. This arrangement is stabilized by intramolecular O—H...O hydrogen bonds between water and carboxylate. Further O—H...O hydrogen bonds between coordinating and non-coordinating water and carboxylate produce layers of molecules that extend parallel to (001. The organic ligands project above and below the plane. Those ligands of adjacent planes are interdigitated and there are π–π interactions between them with centroid–centroid distances of 3.552 (2 and 3.767 (2 Å that generate a three-dimensional supramolecular structure.

Normal Force Influence on 3D Texture Parameters Characterizing the Friction Couple Steel – PBT + 10 % PTFE

Directory of Open Access Journals (Sweden)

C. Georgescu

2014-03-01

Full Text Available This study presents the influence of the normal force on the surface quality of the friction couple steel – polybutylene terephthalate (PBT + 10 % polytetrafluoroethylene (PTFE. There were calculated the average values of the amplitude and functional parameters, as obtained from investigating square areas on the wear tracks, with the help of a proposed methodology, for initial and tested surfaces generated on the blocks and on counterpart ring made of rolling bearing steel, for the following test conditions: three normal forces (F = 1 N, F = 2.5 N and F =5 N, three sliding speeds (v = 0.25 m/s, v = 0.50 m/s and v = 0.75 m/s and a sliding distance of L = 7500 m. The conclusion of the research study was that the tested normal force range has an insignificant influence on the surface quality for the tested materials and parameters. This friction couple could be recommended for variable conditions (speed and load in dry regimes.

Prevalence of overweight, obesity and thinness in 9-10 year old children in Mauritius.

Science.gov (United States)

Caleyachetty, Rishi; Rudnicka, Alicja R; Echouffo-Tcheugui, Justin B; Siegel, Karen R; Richards, Nigel; Whincup, Peter H

2012-07-23

To document the prevalence of overweight, obesity and thinness in 9-10 year old children in Mauritius. 412 boys and 429 girls aged 9-10 years from 23 primary schools were selected using stratified cluster random sampling. All data was cross-sectional and collected via anthropometry and self-administered questionnaire. Outcome measures were BMI (kg/m2), prevalence of overweight, obesity (International Obesity Task Force definitions) and thinness (low BMI for age). Linear and logistic regression analyses, accounting for clustering at the school level, were used to assess associations between gender, ethnicity, school location, and school's academic performance (average) to each outcome measure. The distribution of BMI was marginally skewed with a more pronounced positive tail in the girls. Median BMI was 15.6 kg/m2 in boys and 15.4 kg/m2 in girls, respectively. In boys, prevalence of overweight was 15.8% (95% CI: 12.6, 19.6), prevalence of obesity 4.9% (95% CI: 3.2, 7.4) and prevalence of thinness 12.4% (95% CI: 9.5, 15.9). Among girls, 18.9% (95% CI: 15.5, 22.9) were overweight, 5.1% (95% CI: 3.4, 7.7) were obese and 13.1% (95% CI: 10.2, 16.6) were thin. Urban children had a slightly higher mean BMI than rural children (0.5 kg/m2, 95% CI: 0.01, 1.00) and were nearly twice as likely to be obese (6.7% vs. 4.0%; adjusted odds ratio 1.6; 95% CI: 0.9, 3.5). Creole children were less likely to be classified as thin compared to Indian children (adjusted odds ratio 0.3, 95% CI: 0.2, 0.6). Mauritius is currently in the midst of nutritional transition with both a high prevalence of overweight and thinness in children aged 9-10 years. The coexistence of children representing opposite sides of the energy balance equation presents a unique challenge for policy and interventions. Further exploration is needed to understand the specific causes of the double burden of malnutrition and to make appropriate policy recommendations.

Effect of hydrogen charging on the stability of SAE 10B22 steel surface in alkaline solutions

International Nuclear Information System (INIS)

Modiano, S.; Carreno, J.A.; Fugivara, C.S.; Benedetti, A.V.; Mattos, O.R.

2005-01-01

The influence of hydrogen charging into a quenched and tempered boron steel membrane electrode (SAE 10B22) was studied using borate buffer (pH 8.4) and NaOH solutions (pH 12.7), with or without the addition of 0.01 M EDTA. At the hydrogen input side, hydrogen charging influenced cyclic voltammograms increasing the anodic charge of iron(II) hydroxide formation, and decreasing the donor density of passive films. These results suggest that the hydrogen ingress caused instability of metallic surface, increasing the surface area activity

Ion exchange and electrochemical evaluation of the microporous phosphate Li9Fe7(PO4)10

International Nuclear Information System (INIS)

Becht, Gregory A.; Vaughey, John T.; Britt, Robin L.; Eagle, Cassandra T.; Hwu, Shiou-Jyh

2008-01-01

A new lithium iron(III) phosphate, Li 9 Fe 7 (PO 4 ) 10 , has been synthesized and is currently under electrochemical evaluation as an anode material for rechargeable lithium-ion battery applications. The sample was prepared via the ion exchange reaction of Cs 5 K 4 Fe 7 (PO 4 ) 10 1 in the 1 M LiNO 3 solution under hydrothermal conditions at 200 deg. C. The fully Li + -exchanged sample Li 9 Fe 7 (PO 4 ) 10 2 cannot yet be synthesized by conventional high-temperature, solid-state methods. The parent compound 1 is a member of the Cs 9-x K x Fe 7 (PO 4 ) 10 series that was previously isolated from a high-temperature (750 deg. C) reaction employing the eutectic CsCl/KCl molten salt. The polycrystalline solid 1 was first prepared in a stoichiometric reaction via conventional solid-state method then followed by ion exchange giving rise to 2. Both compounds adopt three-dimensional structures that consist of orthogonally interconnected channels where electropositive ions reside. It has been demonstrated that the Cs 9-x K x Fe 7 (PO 4 ) 10 series possesses versatile ion exchange capabilities with all the monovalent alkali metal and silver cations due to its facile pathways for ion transport. 1 and 2 were subject to electrochemical analysis and preliminary results suggest that the latter can be considered as an anode material. Electrochemical results indicate that Li 9 Fe 7 (PO 4 ) 10 is reduced below 1 V (vs. Li) to most likely form a Fe(0)/Li 3 PO 4 composite material, which can subsequently be cycled reversibly at relatively low potential. An initial capacity of 250 mAh/g was measured, which is equivalent to the insertion of thirteen Li atoms per Li 9+x Fe 7 (PO 4 ) 10 (x = 13) during the charge/discharge process (Fe 2+ + 2e → Fe 0 ). Furthermore, 2 shows a lower reduction potential (0.9 V), by approximately 200 mV, and much better electrochemical reversibility than iron(III) phosphate, FePO 4 , highlighting the value of improving the ionic conductivity of the sample

DEVELOPMENT OF SOFTWARE “PRODSP-1.0” FOR OPTIMIZATION OF THE DEPHOSPHORIZATION PROCESSES IN ARC STEEL-FURNACES FOR TECHNOLOGICAL LINE-UP OF RUP “BMZ”

Directory of Open Access Journals (Sweden)

A. A. Chichko

2006-01-01

Full Text Available The software “ProDSP-1,0” allowing to forecast the dynamics of the dephosphorizaiton process at casting course in arc steel-furnace, is worked out. The examples of working of different program operating regimes, showing the possibilities of phosphorus control in steel-furnace of RUP ‘'BMZ'' are given.

Benzo(a)pyrene-7,8-dihydrodiol 9,10-oxide adenosine and deoxyadenosine adducts: structure and stereochemistry.

Science.gov (United States)

Jeffrey, A M; Grzeskowiak, K; Weinstein, I B; Nakanishi, K; Roller, P; Harvey, R G

1979-12-14

The structure and absolute stereoconfigurations of four adenosine adducts with (+/-)-7 alpha,8 beta-dihydroxy-9 beta, 10 beta-epoxy-7,8,9,10-tetrahydrobenzo(a)pyrene (BPDE) and their deoxyadenosine analogs have been determined. They result from both cis and trans addition of the N6 amino group of ademine to the 10 position of both enantiomers of BDPE. This was determined from studies of the nuclear magnetic resonance spectra, mass spectra, and circular dichroism spectra, as well as from their pKa values and chemical reactivities.

10 + 10 + 10 = 24?

DEFF Research Database (Denmark)

Andersen, Johannes

2014-01-01

efter en 10+10+10 timers model. Ifølge lektor og samfundsforsker Johannes Andersen ved Institut for statskundskab på Aalborg Universitet, er antallet af stress ramte danskere steget fra 5 procent i 1989 til mere end 12 procent i 2010. Således tyder noget på, at danskerne ikke får den fornødne hvile....

Extracts from Kang-T'ieh (Steel), Issue Number 10 - Communist China

National Research Council Canada - National Science Library

1960-01-01

.... Big Drop in Pig Iron Consumption for converter steel production, 3. Surpass the Open-Hearth Furnace, Catch up with the electric furnace and struggle for high quality and varieties of products in converter steel production, 4...

Zinc supplementation induces CD4+CD25+Foxp3+ antigen-specific regulatory T cells and suppresses IFN-γ production by upregulation of Foxp3 and KLF-10 and downregulation of IRF-1.

Science.gov (United States)

Maywald, Martina; Rink, Lothar

2017-08-01

The essential trace element zinc plays a fundamental role in immune function and regulation since its deficiency is associated with autoimmunity, allergies, and transplant rejection. Thus, we investigated the influence of zinc supplementation on the Th1-driven alloreaction in mixed lymphocyte cultures (MLC), on generation of antigen-specific T cells, and analyzed underlying molecular mechanisms. Cell proliferation and pro-inflammatory cytokine production were monitored by [ 3 H]-thymidine proliferation assay and ELISA, respectively. Analysis of surface and intracellular T cell marker was performed by flow cytometry. Western blotting and mRNA analysis were used for Foxp3, KLF-10, and IRF-1 expression. Zinc supplementation on antigen-specific T cells in physiological doses (50 µM) provokes a significant amelioration of cell proliferation and pro-inflammatory cytokine production after reactivation compared to untreated controls. Zinc administration on MLC results in an increased induction and stabilization of CD4 + CD25 + Foxp3 + and CD4 + CD25 + CTLA-4 + T cells (p zinc-induced upregulation of Foxp3 and KLF-10 and downregulation of IRF-1. However, in resting lymphocytes zinc increases IRF-1. In summary, zinc is capable of ameliorating the allogeneic immune reaction by enhancement of antigen-specific iTreg cells due to modulation of essential molecular targets: Foxp3, KLF-10, and IRF-1. Thus, zinc can be seen as an auspicious tool for inducing tolerance in adverse immune reactions.

Hydrogen absorption kinetics and structural properties of Mg85Ni10Ca5 and Mg90Ni10

International Nuclear Information System (INIS)

Aoki, Masakazu; Saito, Katsushi; Towata, Shin-ichi

2005-01-01

Mg 85 Ni 10 Ca 5 and Mg 90 Ni 10 were prepared by melting mixtures of the elements in mild steel crucibles and pouring them into copper molds. Hydrogen absorption kinetics and structural properties of the alloys were characterized by the volumetric method using a Sievert's apparatus, X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The crystallite size of Mg in Mg 85 Ni 10 Ca 5 , which is evaluated by XRD peak broadening, is about 50% smaller than that in Mg 90 Ni 10 . In addition, the nanometer-scale structure composed of Mg, Mg 2 Ni, Mg 2 Ca was observed in Mg 85 Ni 10 Ca 5 . Mg 85 Ni 10 Ca 5 shows better hydrogen absorption kinetics than Mg 90 Ni 10 in the temperature range of room temperature to 573 K. The better absorption kinetics of Mg 85 Ni 10 Ca 5 is mainly attributed to the nanometer-scale structure

An Evaluation of Grades 9 and 10 Mathematics Textbooks Vis-À-Vis ...

African Journals Online (AJOL)

An Evaluation of Grades 9 and 10 Mathematics Textbooks Vis-À-Vis Fostering Problem Solving Skills. ... Document analysis was carried out on the two textbooks using Mathematics Material Analysis Instrument (MMAI) developed by Karen (1997). Interview was held with two experts from Institute of Curriculum Development ...

Energetic effects of ether and ketone functional groups in 9,10-dihydroanthracene compound

International Nuclear Information System (INIS)

Freitas, Vera L.S.; Gomes, Jose R.B.; Ribeiro da Silva, Maria D.M.C.

2010-01-01

The energetic effects caused by replacing one of the methylene groups in the 9,10-dihydroanthracene by ether or ketone functional groups yielding xanthene and anthrone species, respectively, were determined from direct comparison of the standard (p o = 0.1 MPa) molar enthalpies of formation in the gaseous phase, at T = 298.15 K, of these compounds. The experimental static-bomb combustion calorimetry and Calvet microcalorimetry and the computational G3(MP2)//B3LYP method were used to get the standard molar gas-phase enthalpies of formation of xanthene, (41.8 ± 3.5) kJ . mol -1 , and anthrone, (31.4 ± 3.2) kJ . mol -1 . The enthalpic increments for the substitution of methylene by ether and ketone in the parent polycyclic compound (9,10-dihydroanthracene) are -(117.9 ± 5.5) kJ . mol -1 and -(128.3 ± 5.4) kJ . mol -1 , respectively.

Planar conjugated polymers containing 9,10-disubstituted phenanthrene units for efficient polymer solar cells.

Science.gov (United States)

Li, Guangwu; Kang, Chong; Li, Cuihong; Lu, Zhen; Zhang, Jicheng; Gong, Xue; Zhao, Guangyao; Dong, Huanli; Hu, Wenping; Bo, Zhishan

2014-06-01

Four novel conjugated polymers (P1-4) with 9,10-disubstituted phenanthrene (PhA) as the donor unit and 5,6-bis(octyloxy)benzothiadiazole as the acceptor unit are synthesized and characterized. These polymers are of medium bandgaps (2.0 eV), low-lying HOMO energy levels (below -5.3 eV), and high hole mobilities (in the range of 3.6 × 10(-3) to 0.02 cm(2) V(-1) s(-1) ). Bulk heterojunction (BHJ) polymer solar cells (PSCs) with P1-4:PC71 BM blends as the active layer and an alcohol-soluble fullerene derivative (FN-C60) as the interfacial layer between the active layer and cathode give the best power conversion efficiency (PCE) of 4.24%, indicating that 9,10-disubstituted PhA are potential donor materials for high-efficiency BHJ PSCs. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

’n Retoriese analise van Romeine 9:1–10:4

Directory of Open Access Journals (Sweden)

A.H. (Andries Snyman

2015-06-01

Full Text Available Die artikel is ’n poging om Paulus se retoriese strategie uit die teks self te rekonstrueer, eerder as om ’n klassieke of moderne retoriese model op die teks toe te pas. ’n Voorstel virso ’n teksgesentreerde benadering word kortliks opgesom, gevolg deur ’n beskrywing van die retoriese situasie wat Paulus in die brief wil ondersoek. Daar word geargumenteer dat Romeine 9:1–10:4 ’n integrale deel van Paulus se retoriese strategie vorm met die doel om sy gehoor te oortuig om sy siening van God se verlossingsplan, asook sy beoogde sending na Spanje te steun. In die proses van oorreding gebruik hy verskillende soorte argumente en retoriese tegnieke om die trefkrag van sy kommunikasie te verhoog. Die gevolgtrekkingis dat ’n teksgesentreerde benadering (met fokus op die funksionele aspekte van die teks ’n beter alternatief as die bestaande benaderings (met fokus op die formele aspekte van die teks bied. A rhetorical analysis of Romans 9:1-10:4. This article is an attempt to reconstruct Paul’s rhetorical strategy from the text itself, rather than applying ancient or modern rhetorical models to his letters. A proposal for such a text-centred approach is briefly summarised, followed by a discussion of the rhetorical situation that Paul wants to address in this letter. It is argued that Romans 9:1–10:4 forms an integral part of his rhetorical strategy, aimed at persuading his audience in Rome to support his view on God’s plan of salvationas well as his forthcoming mission to Spain. In the process of persuasion Paul uses various types of argument and rhetorical techniques to enhance the impact of his communication.The conclusion is that a text-centred approach (with its focus on the functional aspects of the text provides a better alternative to existing approaches (which focus on the formal aspects of the text.

Tetraspanin CD9 modulates human lymphoma cellular proliferation via histone deacetylase activity

Energy Technology Data Exchange (ETDEWEB)

Herr, Michael J. [Vascular Biology Center of Excellence, The University of Tennessee Health Science Center, Memphis, TN 38163 (United States); Department of Medicine, The University of Tennessee Health Science Center, Memphis, TN 38163 (United States); Department of Molecular Sciences, The University of Tennessee Health Science Center, Memphis, TN 38163 (United States); Department of Surgery, The University of Tennessee Health Science Center, Memphis, TN 38163 (United States); Longhurst, Celia M.; Baker, Benjamin [Vascular Biology Center of Excellence, The University of Tennessee Health Science Center, Memphis, TN 38163 (United States); Homayouni, Ramin [Department of Biology, Bioinformatics Program, University of Memphis, Memphis, TN 38152 (United States); Speich, Henry E.; Kotha, Jayaprakash [Vascular Biology Center of Excellence, The University of Tennessee Health Science Center, Memphis, TN 38163 (United States); Jennings, Lisa K., E-mail: ljennings@uthsc.edu [Vascular Biology Center of Excellence, The University of Tennessee Health Science Center, Memphis, TN 38163 (United States); Department of Medicine, The University of Tennessee Health Science Center, Memphis, TN 38163 (United States); Department of Molecular Sciences, The University of Tennessee Health Science Center, Memphis, TN 38163 (United States); Department of Surgery, The University of Tennessee Health Science Center, Memphis, TN 38163 (United States); Department of Biology, Bioinformatics Program, University of Memphis, Memphis, TN 38152 (United States)

2014-05-16

Highlights: • CD9 is differentially expressed in human Burkitt’s lymphoma cells. • We found that CD9 expression promotes these cells proliferation. • CD9 expression also increases HDAC activity. • HDAC inhibition decreased both cell proliferation and importantly CD9 expression. • CD9 may dictate HDAC efficacy and play a role in HDAC regulation. - Abstract: Non-Hodgkin Lymphoma (NHL) is a type of hematological malignancy that affects two percent of the overall population in the United States. Tetraspanin CD9 is a cell surface protein that has been thoroughly demonstrated to be a molecular facilitator of cellular phenotype. CD9 expression varies in two human lymphoma cell lines, Raji and BJAB. In this report, we investigated the functional relationship between CD9 and cell proliferation regulated by histone deacetylase (HDAC) activity in these two cell lines. Introduction of CD9 expression in Raji cells resulted in significantly increased cell proliferation and HDAC activity compared to Mock transfected Raji cells. The increase in CD9–Raji cell proliferation was significantly inhibited by HDAC inhibitor (HDACi) treatment. Pretreatment of BJAB cells with HDAC inhibitors resulted in a significant decrease in endogenous CD9 mRNA and cell surface expression. BJAB cells also displayed decreased cell proliferation after HDACi treatment. These results suggest a significant relationship between CD9 expression and cell proliferation in human lymphoma cells that may be modulated by HDAC activity.

Study of the effect of an increase in phosphorus content on the corrosion resistance of austenitic stainless steels type 18-10

International Nuclear Information System (INIS)

Charbonnier, J.C.; Thomas, B.

1982-01-01

The work is carried out on Z 6 CN 18-10 steels with P concentrations in the range of 0.004 to 0.127%, to examine intercrystalline corrosion, pitting corrosion and cavern corrosion. It is concluded that a slight increase in the P content above 0.04% is compatible with an acceptable corrosion behaviour [fr

Precipitation behavior of Laves phase and its effect on toughness of 9Cr-2Mo ferritic-martensitic steel

International Nuclear Information System (INIS)

Hosoi, Y.; Wade, N.; Kunimitsu, S.; Urita, T.

1986-01-01

This study clarified the relationship between the toughness of a 9Cr-2Mo dual phase steel and precipitates formed during aging, with special attention to the Laves phase (Fe 2 Mo). The ductile-brittle transition temperature (DBTT) is increased and the upper shelf energy decreased when the Laves phase begins to precipitate during aging. Electron microscopy and X-ray diffraction indicate that elimination of Si in the steel reduces the precipitation of the Laves phase and results in maintaining good toughness. It is also noted that the toughness of the steel is controlled by the total amount of precipitates (Laves + carbides) in the aging at 873 K for more than 3.6x10 3 ks. A time-temperature-precipitation diagram for the Laves phase is established and it clearly shows that the precipitation of the Laves phase is markedly retarded by the decrease of Si content. In Si-free steel, no Laves phase is observed in the temperature and time range investigated. (orig.)

The self-antigen, thyroglobulin, induces antigen-experienced CD4+ T cells from healthy donors to proliferate and promote production of the regulatory cytokine, interleukin-10, by monocytes

DEFF Research Database (Denmark)

Nielsen, Claus Kim Hostein; Galdiers, Marcel P; Hedegaard, Chris Juul

2010-01-01

Thyroglobulin (TG), as autoantigen, induces in vitro proliferation of T and B cells from normal individuals, but the cytokine production differs from that in patients with autoimmune thyroid disease. Here, we investigate whether normal T cells responding to TG are naive, or have previously....... Whereas TT induced pro-inflammatory cytokines [interleukin-2 (IL-2)/interferon-gamma (IFN-gamma)/IL-4/IL-5], TG evoked persistent release of the regulatory IL-10. Some donors, however, also responded with late IFN-gamma production, suggesting that the regulation by IL-10 could be overridden. Although...... monocytes were prime producers of IL-10 in the early TG response, a few IL-10-secreting CD4(+) T cells, primarily with CD45RO(+) memory phenotype, were also detected. Furthermore, T-cell depletion from the mononuclear cell preparation abrogated monocyte IL-10 production. Our findings indicate active...

Synthesis of iridacarborane halide complexes [(η-9-SMe2-7,8-C2B9H10)IrX2]2 (X=Cl, Br, I)

International Nuclear Information System (INIS)

Kudinov, A.R.; Perekalin, D.S.; Petrovskij, P.V.

2001-01-01

By interaction between Na[9-SMe 2 -7,8-C 2 B 9 H 10 ] and [(Cod)IrCl] 2 (Cod - cycloocta-1,5-diene) iridium complex (η-9-SMe 2 -7,8-C 2 B 9 H 10 )Ir(Cod), which under the action of anhydrous hydrohalogenic acids HX (X=Cl, Br, I) yields iridacarborane halide complexes [(η-9-SMe 2 -7,8-C 2 B 9 H 10 )IrX 2 ] 2 , being analogs of cyclopentadienyl complexes [(C 5 Me 5 )IrX 2 ] 2 . The complexes prepared were characterized on the basis of data of elementary analysis and 1 H, 11 B NMR spectra [ru

An Evaluation of Grades 9 and 10 Mathematics Textbooks Vis-À-Vis ...

African Journals Online (AJOL)

An Evaluation of Grades 9 and 10 Mathematics Textbooks Vis-À-Vis Fostering Problem Solving Skills. ... Frequently Asked Questions about PDFs. Alternatively, you can download the PDF file directly to your computer, from where it can be opened using a PDF reader. To download the PDF, click the Download link above.

Antidiarrheal Thymol Derivatives from Ageratina glabrata. Structure and Absolute Configuration of 10-Benzoyloxy-8,9-epoxy-6-hydroxythymol Isobutyrate

Directory of Open Access Journals (Sweden)

Celia Bustos-Brito

2016-09-01

Full Text Available Chemical investigation of the leaves from Ageratina glabrata yielded four new thymol derivatives, namely: 10-benzoyloxy-8,9-dehydro-6-hydroxythymol isobutyrate (4, 10-benzoyloxy-8,9-dehydrothymol (5, 10-benzoyloxythymol (6 and 10-benzoyloxy-6,8-dihydroxy-9-isobutyryl-oxythymol (7. In addition, (8S-10-benzoyloxy-8,9-epoxy-6-hydroxythymol isobutyrate (1, together with other two already known thymol derivatives identified as 10-benzoyloxy-8,9-epoxy-6-methoxythymol isobutyrate (2 and 10-benzoyloxy-8,9-epoxythymol isobutyrate (3 were also obtained. In this paper, we report the structures and complete assignments of the 1H and 13C-NMR data of compounds 1–7, and the absolute configuration for compound 1, unambiguously established by single crystal X-ray diffraction, and evaluation of the Flack parameter. The in vitro antiprotozoal assay showed that compound 1 and its derivative 1a were the most potent antiamoebic and antigiardial compounds. Both compounds showed selectivity and good antiamoebic activity comparable to emetine and metronidazole, respectively, two antiprotozoal drugs used as positive controls. In relation to anti-propulsive effect, compound 1 and 1a showed inhibitory activity, with activities comparable to quercetin and compound 9, two natural antipropulsive compounds used as positive controls. These data suggest that compound 1 may play an important role in antidiarrheal properties of Ageratina glabrata.

The integrity of 9Cr-1Mo to stainless steel transition joints in AGR steam generators

International Nuclear Information System (INIS)

James, D.W.; Neumann, P.; Soo, J.

1982-01-01

The metallurgical aspects of the transition joint between 9Cr-1Mo and 316 stainless steel boiler tube sections are reviewed. A large minimum superheat margin (106 0 C) between the dryout zone and the 9Cr-1Mo to stainless steel transition joint was specified in the original design to eliminate the risk of wetting the stainless steel which is susceptible to stress corrosion cracking. However, small defects were discovered in the welds between the 9Cr-1Mo and Sanicro (72%Ni-16%Cr-10%Fe) transition piece, resulting from dilution of the weld pool by nickel from the transition piece. This led to the possibility of weld failure as a result of creep crack growth in service, and any significant reduction in operating temperature would mean that the large superheat margin could not be sustained. The creep properties of the joints, together with the transition joint temperature distribution, enabled tube failure rates to be determined as a function of operating temperature. A probabilistic model was developed so that the transition joint could be operated within a temperature 'window', the lower temperature limit being determined by stress corrosion considerations and the upper limit being set by creep rate limitations. This allows full load performance from the boilers throughout the anticipated life of the plant. (author)

9th and 10th Asian Symposium on Computer Mathematics

CERN Document Server

Lee, Wen-shin; Sato, Yosuke

2014-01-01

This book covers original research and the latest advances in symbolic, algebraic and geometric computation; computational methods for differential and difference equations, symbolic-numerical computation; mathematics software design and implementation; and scientific and engineering applications based on features, invited talks, special sessions and contributed papers presented at the 9th (in Fukuoka, Japan in 2009) and 10th (in Beijing China in 2012) Asian Symposium on Computer Mathematics (ASCM). Thirty selected and refereed articles in the book present the conference participants’ ideas and views on researching mathematics using computers.

PDE9A, PDE10A, and PDE11A expression in rat trigeminovascular pain signalling system

DEFF Research Database (Denmark)

Kruse, Lars S; Møller, Morten; Tibaek, Maiken

2009-01-01

as neocortex and cerebellar cortex. Real-time PCR and Western blotting showed that PDE9A, PDE10A and PDE11A are expressed in components of the rat trigeminovascular pain signalling system including middle cerebral artery, basilar artery, meninges, trigeminal ganglion and spinal trigeminal nucleus. Aorta...... and mesenteric artery as well as cerebral neocortex and cerebellar cortex also showed expression of PDE9A, PDE10A and PDE11A. Immunohistochemistry revealed that PDE9A, PDE10A and PDE11A are localised in the cytosol of nerve cell bodies of the trigeminal ganglion. We here present, for the first time...

10 CFR 76.5 - Communications.

Science.gov (United States)

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Communications. 76.5 Section 76.5 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS General Provisions § 76.5..., for example, Electronic Information Exchange, or CD-ROM. Electronic submissions must be made in a...

CdTe/TiO{sub 2} nanocomposite material for photogenerated cathodic protection of 304 stainless steel

Energy Technology Data Exchange (ETDEWEB)

Wang, Xiu-tong, E-mail: xiutongwang@gmail.com [Institutes of Oceanology, Chinese Academy of Sciences, Qingdao 266071 China (China); Wei, Qin-yi, E-mail: weiqiny200@163.com [Institutes of Oceanology, Chinese Academy of Sciences, Qingdao 266071 China (China); University of Chinese Academy of Sciences, 19 (Jia) Yuquan Road, Beijing 100049 (China); Zhang, Liang, E-mail: zzll20081988@126.com [CNOOC Information Technology co., Ltd. Beijing Branch, Beijing 100029 China (China); Sun, Hao-fen, E-mail: fyqfyx@163.com [School of Environmental and Municipal Engineering Qingdao, Qingdao Technological University, Qingdao 266033 China (China); Li, Hong, E-mail: lhqdio1987@163.com [Institutes of Oceanology, Chinese Academy of Sciences, Qingdao 266071 China (China); Zhang, Qiao-xia, E-mail: qiaoxiazhang1989@163.com [Institutes of Oceanology, Chinese Academy of Sciences, Qingdao 266071 China (China)

2016-06-15

Graphical abstract: - Highlights: • The photoelectric properties of TiO{sub 2} could greatly improve by doping with CdTe. • The cathodic protection property of the CdTe/TiO{sub 2} was superior to that of pure TiO{sub 2}. • The protective action of the CdTe/TiO{sub 2} for 304SS could be maintained in the dark. - Abstract: TiO{sub 2} nanotubes were fabricated by the anodization method, and CdTe was deposited on them via electrochemical deposition method. The optimal performance of the CdTe/TiO{sub 2} composites was achieved via changing the acidity of the electrolyte. Scanning electron microscopy, energy dispersive spectroscopy and X-ray diffraction were used to investigate the surface morphology, elemental analysis and phase characteristics of the composite materials. Some electrochemical tests, such as open-circuit potential, current variation versus time were carried out to investigate the photogenerated cathodic protection of 304 stainless steel by CdTe/TiO{sub 2}. The results indicated that the cathodic protection performance of the CdTe/TiO{sub 2} composite was superior to that of pure TiO{sub 2} in the wavelength of visible light. The CdTe/TiO{sub 2} composite exhibited optimal photogenerated cathodic protection properties under visible light for the corrosion potential of 304 stainless steel shifted negatively to −850 mV when the concentration of HCl in the deposition electrolyte was 1 mol/L.

Steamside Oxidation Behavior of Experimental 9%Cr Steels

Energy Technology Data Exchange (ETDEWEB)

Dogan, O.N.; Holcomb, G.R.; Alman, D.E.; Jablonski, P.D.

2007-10-01

Reducing emissions and increasing economic competitiveness require more efficient steam power plants that utilize fossil fuels. One of the major challenges in designing these plants is the availability of materials that can stand the supercritical and ultra-supercritical steam conditions at a competitive cost. There are several programs around the world developing new ferritic and austenitic steels for superheater and reheater tubes exposed to the advanced steam conditions. The new steels must possess properties better than current steels in terms of creep strength, steamside oxidation resistance, fireside corrosion resistance, and thermal fatigue resistance. This paper introduces a series of experimental 9%Cr steels containing Cu, Co, and Ti. Stability of the phases in the new steels is discussed and compared to the phases in the commercially available materials. The steels were tested under both the dry and moist conditions at 650ºC for their cyclical oxidation resistance. Results of oxidation tests are presented. Under the moist conditions, the experimental steels exhibited significantly less mass gain compared to the commercial P91 steel. Microstructural characterization of the scale revealed different oxide compositions.

Process for manufacturing bis(2-methoxyethyl)-2,3,6,7-tetracyano-1,4,5,8,9,10-hexazaanthracene

Science.gov (United States)

Rasmussen, Paul George; Lawton, Richard Graham

2014-06-03

A process to manufacture substituted tetracyano-hexaazatricyclics with the substitutions occurring at the 9 and 10 hydrogens. The process begins with 2,3-dichloro-5,6-dicyanopyrazine, which is reacted to form the desired tetracyano-hexaazatricyclic. Different process embodiments enable different reaction paths to the desired tetracyano-hexaazatricyclic. Different tetracyano-hexaazatricyclic embodiments include bis(2-methoxyethyl)-2,3,6,7-tetracyano-1,4,5,8,9,10-hexazaanthracene and bis(2-methoxyethoxyethyl)-2,3,6,7-tetracyano-1,4,5,8,9,10-hexazaanthracen- e.

9Be(d,n)10B-based neutron sources for BNCT

International Nuclear Information System (INIS)

Capoulat, M.E.; Herrera, M.S.; Minsky, D.M.; González, S.J.; Kreiner, A.J.

2014-01-01

In the frame of accelerator-based BNCT, the 9 Be(d,n) 10 B reaction was investigated as a possible source of epithermal neutrons. In order to determine the configuration in terms of bombarding energy, target thickness and Beam Shaping Assembly (BSA) design that results in the best possible beam quality, a systematic optimization study was carried out. From this study, the optimal configuration resulted in tumor doses ≥40 Gy-Eq, with a maximum value of 51 Gy-Eq at a depth of about 2.7 cm, in a 60 min treatment. The optimal configuration was considered for the treatment planning assessment of a real Glioblastoma Multiforme case. From this, the resulted dose performances were comparable to those obtained with an optimized 7 Li(p,n)-based neutron source, under identical conditions and subjected to the same clinical protocol. - Highlights: • Study of the 9 Be(d,n) 10 B reaction as a source of epithermal neutrons for BNCT. • Evaluation of the optimal configuration of target thickness, deuteron energy and BSA design. • Computational dose assessment for brain tumor treatments using the MCNP code. • Treatment planning assessment of a particular clinical Glioblastoma Multiforme case. • Dose performances were comparable to those obtained with an optimized 7 Li(p,n)-based source

Atom-Probe Tomographic Investigations of a Precipitation-Strengthened HSLA-115 Steel and a Ballistic-Resistant 10 wt. % Ni Steel for Naval Applications

Science.gov (United States)

Jain, Divya

High performance structural materials are needed for Naval applications which require an excellent combination of yield strength, low-temperature impact toughness, ductility, ballistic-resistance, and weldability. This research investigates precipitation-strengthened HSLA-115 steels and ballistic-resistant 10 wt. % Ni steels, which have emerged as promising alternatives to the widely used HSLA-100 steels for Naval applications. HSLA-115 is a Cu-bearing high-strength low-carbon martensitic steel and has been used in the flight deck of the recently built U.S. Navy CVN-78 aircraft carrier. It is typically used in conditions with overaged Cu precipitates, to obtain acceptable impact toughness and ductility at 115 ksi (793 MPa) yield strength. However, overaging of Cu precipitates limits its strength and applications. This research demonstrates that aging at 550 °C facilitates the co-precipitation of sub-nanometer sized M2C carbides and Cu precipitates in high number density (˜1023 m-3) in HSLA-115. 3-D atom-probe tomography (APT) investigation reveals that Cu precipitates form first, followed by the nucleation of M2C carbides, which are co-located with Cu precipitates and are distributed heterogeneously at lath-boundaries and dislocations, indicating heterogeneous nucleation of M2C. Carbon redistribution during quenching (following the austenitization) and subsequent aging at 550 °C is followed using APT. Segregation of C (3-6 at. % C) is observed at martensitic lath-boundaries in the as-quenched and 0.12 h aged conditions. On further aging, C redistributes, forming cementite and M 2C carbides, whose composition and morphology evolves with aging time. Precipitation kinetics of M2C carbides is intertwined with Cu precipitates; temporal evolution of Cu precipitates and M2C carbides is characterized in terms of their mean radii, number densities, and volume fractions and correlated with the bulk mechanical properties. Precipitation of M2C carbides offsets the softening

Study of the unbound nuclei {sup 7,9}He and {sup 10}Li; Etude de la structure des noyaux non lies {sup 7,9}He et {sup 10}Li

Energy Technology Data Exchange (ETDEWEB)

Al Falou, H

2007-07-15

The unbound nuclei {sup 7,9}He and {sup 10}Li have been investigated via the high-energy breakup of beams of neutron-rich nuclei ({sup 8}He, {sup 11}Be and {sup 14}B). The decay-energy spectra were reconstructed from coincident measurements of the charged fragments ({sup 6,8}He and {sup 9}Li) with a {delta}E-E telescope (CHARISSA) and the neutrons with the DEMON array. A theoretical approach based on the sudden approximation was used to model the reactions populating the unbound final states. The calculated decay-energy spectra were convoluted with the response function of the experimental setup using a simulation developed specifically for the present study and compared with the experimental results. The {sup 10}Li system was produced using an {sup 11}Be beam and the results confirm the continuation of the inversion of the {nu}1s1/2 and {nu}0p1/2 levels in the N = 7 isotopic chain. The {sup 9}He system was produced in two different ways with the breakup of {sup 11}Be and {sup 14}B, and was the most exotic system studied here. In this case, a structure was observed at very low decay energy which very probably corresponds to a virtual s state (a{sub s} {approx_equal} -2 - 0 fm). This result suggests that the level inversion also occurs in {sup 9}He, but with a much weaker core-neutron interaction than for {sup 10}Li (a{sub s} equals -14 {+-} 2 fm). For the data acquired from the breakup of the {sup 14}B beam, the decay energy spectrum exhibits a resonance around E{sub r} equals 1.2 MeV, which most probably corresponds to an excited 1/2{sup -} state in {sup 9}He. The {sup 7}He system was investigated with three different beams ({sup 8}He, {sup 11}Be and {sup 14}B). No evidence for the existence of the proposed low-lying (E{sub r} {approx} 1 MeV) spin-orbit partner (1/2{sup -}) of the ground state (3/2{sup -}) could be found. (author)

Probiotic Bifidobacterium breve induces IL-10-producing Tr1 cells in the colon.

Directory of Open Access Journals (Sweden)

Seong Gyu Jeon

Full Text Available Specific intestinal microbiota has been shown to induce Foxp3(+ regulatory T cell development. However, it remains unclear how development of another regulatory T cell subset, Tr1 cells, is regulated in the intestine. Here, we analyzed the role of two probiotic strains of intestinal bacteria, Lactobacillus casei and Bifidobacterium breve in T cell development in the intestine. B. breve, but not L. casei, induced development of IL-10-producing Tr1 cells that express cMaf, IL-21, and Ahr in the large intestine. Intestinal CD103(+ dendritic cells (DCs mediated B. breve-induced development of IL-10-producing T cells. CD103(+ DCs from Il10(-/-, Tlr2(-/-, and Myd88(-/- mice showed defective B. breve-induced Tr1 cell development. B. breve-treated CD103(+ DCs failed to induce IL-10 production from co-cultured Il27ra(-/- T cells. B. breve treatment of Tlr2(-/- mice did not increase IL-10-producing T cells in the colonic lamina propria. Thus, B. breve activates intestinal CD103(+ DCs to produce IL-10 and IL-27 via the TLR2/MyD88 pathway thereby inducing IL-10-producing Tr1 cells in the large intestine. Oral B. breve administration ameliorated colitis in immunocompromised mice given naïve CD4(+ T cells from wild-type mice, but not Il10(-/- mice. These findings demonstrate that B. breve prevents intestinal inflammation through the induction of intestinal IL-10-producing Tr1 cells.

Probiotic Bifidobacterium breve induces IL-10-producing Tr1 cells in the colon.

Science.gov (United States)

Jeon, Seong Gyu; Kayama, Hisako; Ueda, Yoshiyasu; Takahashi, Takuya; Asahara, Takashi; Tsuji, Hirokazu; Tsuji, Noriko M; Kiyono, Hiroshi; Ma, Ji Su; Kusu, Takashi; Okumura, Ryu; Hara, Hiromitsu; Yoshida, Hiroki; Yamamoto, Masahiro; Nomoto, Koji; Takeda, Kiyoshi

2012-01-01

Specific intestinal microbiota has been shown to induce Foxp3(+) regulatory T cell development. However, it remains unclear how development of another regulatory T cell subset, Tr1 cells, is regulated in the intestine. Here, we analyzed the role of two probiotic strains of intestinal bacteria, Lactobacillus casei and Bifidobacterium breve in T cell development in the intestine. B. breve, but not L. casei, induced development of IL-10-producing Tr1 cells that express cMaf, IL-21, and Ahr in the large intestine. Intestinal CD103(+) dendritic cells (DCs) mediated B. breve-induced development of IL-10-producing T cells. CD103(+) DCs from Il10(-/-), Tlr2(-/-), and Myd88(-/-) mice showed defective B. breve-induced Tr1 cell development. B. breve-treated CD103(+) DCs failed to induce IL-10 production from co-cultured Il27ra(-/-) T cells. B. breve treatment of Tlr2(-/-) mice did not increase IL-10-producing T cells in the colonic lamina propria. Thus, B. breve activates intestinal CD103(+) DCs to produce IL-10 and IL-27 via the TLR2/MyD88 pathway thereby inducing IL-10-producing Tr1 cells in the large intestine. Oral B. breve administration ameliorated colitis in immunocompromised mice given naïve CD4(+) T cells from wild-type mice, but not Il10(-/-) mice. These findings demonstrate that B. breve prevents intestinal inflammation through the induction of intestinal IL-10-producing Tr1 cells.

75 FR 35611 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-10-10, DC-10-10F, and MD-10-10F...

Science.gov (United States)

2010-06-23

... Airworthiness Directives; McDonnell Douglas Corporation Model DC- 10-10, DC-10-10F, and MD-10-10F Airplanes... certain McDonnell Douglas Model DC-10-10, DC-10-10F, and MD-10-10F airplanes. That NPRM was published in... amends Sec. 39.13 by adding the following new AD: 2010-13-06 McDonnell Douglas Corporation: Amendment 39...

Phosphorus-Based Dendrimer ABP Treats Neuroinflammation by Promoting IL-10-Producing CD4(+) T Cells.

Science.gov (United States)

Hayder, Myriam; Varilh, Marjorie; Turrin, Cédric-Olivier; Saoudi, Abdelhadi; Caminade, Anne-Marie; Poupot, Rémy; Liblau, Roland S

2015-11-09

Dendrimers are polyfunctional nano-objects of perfectly defined structure that can provide innovative alternatives for the treatment of chronic inflammatory diseases, including multiple sclerosis (MS). To investigate the efficiency of a recently described amino-bis(methylene phosphonate)-capped ABP dendrimer as a potential drug candidate for MS, we used the classical mouse model of MOG35-55-induced experimental autoimmune encephalomyelitis (EAE). Our study provides evidence that the ABP dendrimer prevents the development of EAE and inhibits the progression of established disease with a comparable therapeutic benefit as the approved treatment Fingolimod. We also show that the ABP dendrimer redirects the pathogenic myelin-specific CD4(+) T cell response toward IL-10 production.

Microstructure and susceptibility to HIBC of 10H2M steel exposed to service conditions of boilers in fossil power plants

International Nuclear Information System (INIS)

Lunarska, E.; Nikiforow, K.; Zielinski, W.; Kurzydlowski, K.J.

2004-01-01

Mechanical properties, microstructure and hydrogen permeation through 10H2M ferrite pearlite steel from boilers of power station being in-service for up to 100000 hours have been systematically analysed in order to correlate the change in susceptibility to HIBC with microstructure features. The change of the pearlite volume fraction, the carbide morphology and the ferrite dislocation structure as a function of in-service time has been evaluated by SEM and TEM analysis. Susceptibility to HIBC has been estimated in the especially elaborated electrochemical measurements of hydrogen permeation. The correlation has been found between the microstructure features and the hydrogen permeation parameters describing the susceptibility to hydrogen induced cracking of steel exploited in water-steam environment. (author)

Oxide fuel fabrication technology development of the FaCT project (5). Current status on 9Cr-ODS steel cladding development for high burn-up fast reactor fuel

International Nuclear Information System (INIS)

Ohtsuka, Satoshi; Kaito, Takeji; Yano, Yasuhide; Yamashita, Shinichiro; Ogawa, Ryuichiro; Uwaba, Tomoyuki; Koyama, Shinichi; Tanaka, Kenya

2011-01-01

This paper describes evaluation results of in-reactor integrity of 9Cr and 12Cr-ODS steel cladding tubes and the plan for reliability improvement in homogeneous tube production, both of which are key points for the commercialized use of ODS steels as long-life fuel cladding tubes. A fuel assembly in the BOR-60 irradiation test including 9Cr and 12Cr-ODS fuel pins has achieved the highest burn-up, i.e. peak burn-up of 11.9at% and peak neutron dose of 51dpa, without any fuel pin rupture and microstructure instability. In another fuel assembly containing 9Cr and 12Cr-ODS steel fuel pins whose peak burn-up was 10.5at%, one 9Cr-ODS steel fuel pin failed near the upper end of the fuel column. A peculiar microstructure change occurred in the vicinity of the ruptured area. The primary cause of this fuel pin rupture and microstructure change was shown to be the presence of metallic Cr inclusions in the 9Cr-ODS steel tube, which had passed an ultrasonic inspection test for defects. In the next stage from 2011 to 2013, the fabrication technology of full pre-alloy 9Cr-ODS steel cladding tube will be developed, where the handling of elemental powder is prohibited in the process. (author)

Simian Immunodeficiency Virus Targeting of CXCR3+ CD4+ T Cells in Secondary Lymphoid Organs Is Associated with Robust CXCL10 Expression in Monocyte/Macrophage Subsets.

Science.gov (United States)

Fujino, Masayuki; Sato, Hirotaka; Okamura, Tomotaka; Uda, Akihiko; Takeda, Satoshi; Ahmed, Nursarat; Shichino, Shigeyuki; Shiino, Teiichiro; Saito, Yohei; Watanabe, Satoru; Sugimoto, Chie; Kuroda, Marcelo J; Ato, Manabu; Nagai, Yoshiyuki; Izumo, Shuji; Matsushima, Kouji; Miyazawa, Masaaki; Ansari, Aftab A; Villinger, Francois; Mori, Kazuyasu

2017-07-01

Glycosylation of Env defines pathogenic properties of simian immunodeficiency virus (SIV). We previously demonstrated that pathogenic SIVmac239 and a live-attenuated, quintuple deglycosylated Env mutant (Δ5G) virus target CD4 + T cells residing in different tissues during acute infection. SIVmac239 and Δ5G preferentially infected distinct CD4 + T cells in secondary lymphoid organs (SLOs) and within the lamina propria of the small intestine, respectively (C. Sugimoto et al., J Virol 86:9323-9336, 2012, https://doi.org/10.1128/JVI.00948-12). Here, we studied the host responses relevant to SIV targeting of CXCR3 + CCR5 + CD4 + T cells in SLOs. Genome-wide transcriptome analyses revealed that Th1-polarized inflammatory responses, defined by expression of CXCR3 chemokines, were distinctly induced in the SIVmac239-infected animals. Consistent with robust expression of CXCL10, CXCR3 + T cells were depleted from blood in the SIVmac239-infected animals. We also discovered that elevation of CXCL10 expression in blood and SLOs was secondary to the induction of CD14 + CD16 + monocytes and MAC387 + macrophages, respectively. Since the significantly higher levels of SIV infection in SLOs occurred with a massive accumulation of infiltrated MAC387 + macrophages, T cells, dendritic cells (DCs), and residential macrophages near high endothelial venules, the results highlight critical roles of innate/inflammatory responses in SIVmac239 infection. Restricted infection in SLOs by Δ5G also suggests that glycosylation of Env modulates innate/inflammatory responses elicited by cells of monocyte/macrophage/DC lineages. IMPORTANCE We previously demonstrated that a pathogenic SIVmac239 virus and a live-attenuated, deglycosylated mutant Δ5G virus infected distinct CD4 + T cell subsets in SLOs and the small intestine, respectively (C. Sugimoto et al., J Virol 86:9323-9336, 2012, https://doi.org/10.1128/JVI.00948-12). Accordingly, infections with SIVmac239, but not with Δ5G, deplete CXCR3

Diffusion and influence of Cu on properties of CdTe thin films and CdTe/CdS cells

Energy Technology Data Exchange (ETDEWEB)

Dzhafarov, T.D.; Yesilkaya, S.S.; Yilmaz Canli, N.; Caliskan, M. [Department of Physics, Yildiz Technical University, Davutpasa, 34210 Istanbul (Turkey)

2005-01-31

The effective diffusion coefficients of Cu for thermal and photodiffusion in the CdTe films have been estimated from resistivity versus duration of thermal or photoannealing curves. In the temperature range 60-200{sup o}C the effective coefficient of thermal diffusion (D{sub t}) and photodiffusion (D{sub ph}) are described as D{sub t}=7.3x10{sup -7}exp(-0.33/kT) and D{sub ph}=4.7x10{sup -8}exp(-0.20/kT). It is found that the diffusion doping of CdTe thin films by Cu at 400{sup o}C results in a sharp decrease of resistivity up to 7 orders of magnitude of p-type material, depending on thickness of Cu film. The comparative study of performance of CdTe(Cu)/CdS and CdTe/CdS cells has been studied. It is shown that the diffusion doping of CdTe film by Cu increases efficiency of CdTe(Cu)/CdS cells from 0.9% to 6.8%. The degradation of photovoltaic parameters of CdTe(Cu)/CdS cell, during testing under forward and reverse bias at room temperature, proceeds at a larger rate than those of CdTe/CdS cell without Cu. The degradation of performance of CdTe(Cu)/CdS cells is tentatively assigned to electrodiffusion of Cu in CdTe, resulting in redistribution of concentration of Cu-related centers in CdTe film and heterojunction region.

Stress corrosion (Astm G30-90 standard) in 08x18H10T stainless steel of nuclear fuel storage pool in WWER reactors

International Nuclear Information System (INIS)

Herrera, V.; Zamora R, L.

1997-01-01

At the water storage of the irradiated nuclear fuel has been an important factor in its management. The actual pools have its walls covered with inoxidable steel and heat exchangers to dissipate the residual heat from fuel. It is essential to control the water purity to eliminate those conditions which aid to the corrosion process in fuel and at related components. The steel used in this research was obtained from an austenitic inoxidizable steel standardized with titanium 08x18H10T (Type 321) similar to one of the two steel coatings used to cover walls and the pools floor. the test consisted in the specimen deformation through an U ply according to the Astm G30-90 standard. The exposition of the deformed specimen it was realized in simulated conditions to the chemical regime used in pools. (Author)

The low-temperature structural behavior of sodium 1-carba-closo-decaborate: NaCB{sub 9}H{sub 10}

Energy Technology Data Exchange (ETDEWEB)

Wu, Hui, E-mail: hui.wu@nist.gov [NIST Center for Neutron Research, National Institute of Standards and Technology, Gaithersburg, MD 20899-6102 (United States); Tang, Wan Si [NIST Center for Neutron Research, National Institute of Standards and Technology, Gaithersburg, MD 20899-6102 (United States); Department of Materials Science and Engineering, University of Maryland, College Park, MD 20742-2115 (United States); Zhou, Wei [NIST Center for Neutron Research, National Institute of Standards and Technology, Gaithersburg, MD 20899-6102 (United States); Tarver, Jacob D. [NIST Center for Neutron Research, National Institute of Standards and Technology, Gaithersburg, MD 20899-6102 (United States); National Renewable Energy Laboratory, Golden, CO 80401 (United States); Stavila, Vitalie [Energy Nanomaterials, Sandia National Laboratories, Livermore, CA 94551 (United States); Brown, Craig M. [NIST Center for Neutron Research, National Institute of Standards and Technology, Gaithersburg, MD 20899-6102 (United States); Udovic, Terrence J., E-mail: udovic@nist.gov [NIST Center for Neutron Research, National Institute of Standards and Technology, Gaithersburg, MD 20899-6102 (United States)

2016-11-15

Two ordered phases of the novel solid superionic conductor sodium 1-carba-closo-decaborate (NaCB{sub 9}H{sub 10}) were identified via synchrotron x-ray powder diffraction in combination with first-principles calculations and neutron vibrational spectroscopy. A monoclinic packing of the large ellipsoidal CB{sub 9}H{sub 10}{sup −} anions prevails at the lowest temperatures, but a first-order transformation to a slightly modified orthorhombic packing is largely complete by 240 K. The CB{sub 9}H{sub 10}{sup −} anion orientational alignments and Na{sup +} cation interstitial sitings in both phases are arranged so as to minimize the cation proximities to the uniquely more positive C-bonded H atoms of the anions. These results provide valuable structural information pertinent to understanding the relatively low-temperature, entropy-driven, order-disorder phase transition for this compound. - Graphical abstract: Ordered monoclinic and orthorhombic NaCB{sub 9}H{sub 10} phases were determined by XRD and DFT computations and corroborated by neutron vibrational spectroscopy. - Highlights: • Two T-dependent ordered structures of Na(1-CB{sub 9}H{sub 10}) were determined by XRD. • The lower-T monoclinic to higher-T orthorhombic transition occurs from 210 to 240 K. • The main structural differences involve changes in the canting of the CB{sub 9}H{sub 10}{sup −} anions. • DFT and neutron vibrational spectroscopy corroborate the lower-T monoclinic structure. • The results are important for understanding the nature of this superionic conductor.

Interleukin-9 receptor α chain mRNA formation in CD8+ T cells producing anti-human immunodeficiency virus type 1 substance(s)

International Nuclear Information System (INIS)

Hossain, M.M.; Tsuchie, H.; Detorio, M.A.; Shirono, H.; Hara, C.; Nishimoto, A.; Saji, A.; Koga, J.; Takata, N.; Maniar, J.K.; Saple, D.G.; Taniguchi, K.; Kageyama, S.; Ichimura, H.; Kurimura, T.

1998-01-01

A search for gene(s) associated with anti-human immunodeficiency virus type 1 (HIV-l) activity of CD8 + T cells was attempted using molecular cloning and the relation between the anti-HIV activity of CD8 + T cells and the interleukin-9 receptor a chain (IL-9R-α) mRNA expression from the cDNA clones obtained was examined. The anti-HIV-l activity of CD8 + T cell culture supernatants was assessed by measuring the level of HIV-l replication in a CD4 + T cell line transfected with an infectious HIV-l DNA clone. IL-9R-a mRNA was assayed by reverse transcriptase-polymerase chain reaction (RT-PCR). Of 5 cases showing high level of anti-HIV-l activity (more than 80% suppression of HIV-l replication), the mRNA was detected in 4 cases. Of 10 cases showing low level of anti-HIV-l activity (less than 80% suppression of HIV-l replication), the mRNA was detected in one case. Soluble recombinant human IL-9 receptor (rhIL-9sR) did not suppress HIV-l replication at a concentration of 1 μg/ml. These data suggest that the IL-9R-a mRNA formation in CD8 + T cells may correlate with and play some role in the anti-HIV-l activity of CD8+ T cells from HIV-l-infected individuals. Key words: CD8+ T cells; anti-HIV-l activity; cytokines; interleukin-9 receptor (authors)

Resident CD141 (BDCA3)+ dendritic cells in human skin produce IL-10 and induce regulatory T cells that suppress skin inflammation.

Science.gov (United States)

Chu, Chung-Ching; Ali, Niwa; Karagiannis, Panagiotis; Di Meglio, Paola; Skowera, Ania; Napolitano, Luca; Barinaga, Guillermo; Grys, Katarzyna; Sharif-Paghaleh, Ehsan; Karagiannis, Sophia N; Peakman, Mark; Lombardi, Giovanna; Nestle, Frank O

2012-05-07

Human skin immune homeostasis, and its regulation by specialized subsets of tissue-residing immune sentinels, is poorly understood. In this study, we identify an immunoregulatory tissue-resident dendritic cell (DC) in the dermis of human skin that is characterized by surface expression of CD141, CD14, and constitutive IL-10 secretion (CD141(+) DDCs). CD141(+) DDCs possess lymph node migratory capacity, induce T cell hyporesponsiveness, cross-present self-antigens to autoreactive T cells, and induce potent regulatory T cells that inhibit skin inflammation. Vitamin D(3) (VitD3) promotes certain phenotypic and functional properties of tissue-resident CD141(+) DDCs from human blood DCs. These CD141(+) DDC-like cells can be generated in vitro and, once transferred in vivo, have the capacity to inhibit xeno-graft versus host disease and tumor alloimmunity. These findings suggest that CD141(+) DDCs play an essential role in the maintenance of skin homeostasis and in the regulation of both systemic and tumor alloimmunity. Finally, VitD3-induced CD141(+) DDC-like cells have potential clinical use for their capacity to induce immune tolerance.

Identification of rust resistance genes Lr10 and Sr9a in Pakistani ...

African Journals Online (AJOL)

Identification of rust resistance genes Lr10 and Sr9a in Pakistani wheat germplasm using PCR based molecular markers. M Babar, AF Mashhadi, A Mehvish, AN Zahra, R Waheed, A Hasnain, S ur-Rahman, N Hussain, M Ali, I Khaliq, A Aziz ...

Core drilling of drillholes ONK-PVA9 and ONK-PVA10 in ONKALO at Olkiluoto 2011

Energy Technology Data Exchange (ETDEWEB)

Toropainen, V. [Suomen Malmi Oy, Espoo (Finland)

2011-10-15

Suomen Malmi Oy (Smoy) core drilled two drillholes for groundwater monitoring stations in ONKALO at Eurajoki, Olkiluoto in 2011. The groundwater monitoring stations are used for monitoring changes in groundwater conditions. The drillhole ONK-PVA9 was drilled in March 2011 and the drillhole ONK-PVA10 in June 2011. The lengths of the drillholes are 15.95 and 20.10 m respectively. The drillholes are 75.7 mm by diameter. The drillhole ONK-PVA9 was drilled in a niche of the access tunnel at chainage 4366 and the ONK-PVA10 in the access tunnel wall at chainage 3851. The hydraulic DE 130 drilling rig was used. The drilling water was taken from the ONKALO drilling water pipeline and premixed sodium fluorescein was used as a label agent in the drilling water. The drillholes were measured with EMS deviation survey tool. In addition to drilling the drillcores were logged and reported by geologist. Geological logging included the following parameters: lithology, foliation, fracture parameters, fractured zones, core loss, weathering, fracture frequency, RQD and rock quality. The main rock types in the drillholes are veined gneiss and pegmatitic granite. The average fracture frequencies in drill cores are 2.9 pcs/m (ONK-PVA9) and 2.3 pcs/m (ONK-PVA10) and the average RQD values 81.6 % and 96.2 % respectively. (orig.)

Final report on key comparison APMP.M.P-K3: Absolute pressure measurements in gas from 3 × 10-6 Pa to 9 × 10-4 Pa

Science.gov (United States)

Yoshida, H.; Arai, K.; Akimichi, H.; Hong, S. S.; Song, H. W.

2011-01-01

The results of a key comparison of ultra-high vacuum standards at two national metrology institutes (NMIJ/AIST and KRISS) are reported. This bilateral comparison was carried out from May 2010 to October 2010 within the framework of the Asia-Pacific Metrology Programme (APMP) to determine their degrees of equivalence at pressures in the range from 3 × 10-6 Pa to 9 × 10-4 Pa. The pilot institute was NMIJ/AIST. Two spinning rotor gauges and two hot cathode ionization gauges were used as the transfer standards. NMIJ/AIST used two calibration systems: the dynamic expansion system (NMIJ-DES) and two-stage flow-dividing system (NMIJ-TFS). KRISS used the dynamic expansion system. The transfer standards were sufficiently stable to meet the requirements of the comparison compared with those of previous international comparisons owing to some improvements of the protocol and the transfer standards. The ultra-high vacuum standards of NMIJ/AIST and KRISS were found to be equivalent within their claimed uncertainties in the range from 3 × 10-6 Pa to 9 × 10-5 Pa. The NMIJ-DES results, which have smaller uncertainty than NMIJ-TFS, were transferred to the corresponding CCM key comparison, CCM.P-K3, in the range from 3 × 10-6 Pa to 9 × 10-5 Pa and it is shown that the NMIJ values were equivalent to the CCM key comparison reference value within the claimed uncertainties. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

Facile fabrication of CdSe/CdS quantum dots and their application on the screening of colorectal cancer

Science.gov (United States)

Cao, Hongfeng; Dong, Quanjin; Hu, Li; Tu, Shiliang; Chai, Rui; Dai, Qiaoqiong

2015-11-01

In this paper, a facile aqueous route to water-soluble CdSe/CdS quantum dots (QDs) under mild conditions has been developed. The samples were characterized by means of transmission electron microscopy, energy-dispersive X-ray spectroscopy, and photoluminescence (PL) spectroscopy. The PL property of the QDs can be controlled by adjusting the reaction time. The CdSe/CdS QDs after 48-h reaction with size of 5 nm have the strongest PL intensity located at 553 nm, and the highest quantum yield of 19.9 %. The obtained QDs were applied for the colorectal cancer screening. The QDs could be conjugated with antibody of aldo-keto reductase family 1, member B10 (AKR1B10) for the detection of AKR1B10. The AKR1B10 in PBS/5 % serum solution with concentration of 1 ng/mL could be well calibrated, and the limit of detection could be lower than 0.05 ng/mL.

Facile fabrication of CdSe/CdS quantum dots and their application on the screening of colorectal cancer

Energy Technology Data Exchange (ETDEWEB)

Cao, Hongfeng; Dong, Quanjin, E-mail: qjdong1508@163.com [Zhejiang Provincial People’s Hospital, Department of Colorectal Surgery (China); Hu, Li [Nanjing University of Science and Technology, School of Environmental and Biological Engineering (China); Tu, Shiliang; Chai, Rui; Dai, Qiaoqiong [Zhejiang Provincial People’s Hospital, Department of Colorectal Surgery (China)

2015-11-15

In this paper, a facile aqueous route to water-soluble CdSe/CdS quantum dots (QDs) under mild conditions has been developed. The samples were characterized by means of transmission electron microscopy, energy-dispersive X-ray spectroscopy, and photoluminescence (PL) spectroscopy. The PL property of the QDs can be controlled by adjusting the reaction time. The CdSe/CdS QDs after 48-h reaction with size of 5 nm have the strongest PL intensity located at 553 nm, and the highest quantum yield of 19.9 %. The obtained QDs were applied for the colorectal cancer screening. The QDs could be conjugated with antibody of aldo-keto reductase family 1, member B10 (AKR1B10) for the detection of AKR1B10. The AKR1B10 in PBS/5 % serum solution with concentration of 1 ng/mL could be well calibrated, and the limit of detection could be lower than 0.05 ng/mL.

A spectrophotometric method of determining nobium, ranging from 0,01 to 0,10% Nb, in steel with xylene orange after precipitation by tannin

International Nuclear Information System (INIS)

Jurczyk, J.; Capalla, K.; Szeja, K.

1980-01-01

A spectrophotometric method is presented of determining 0,1 to 0,10% niobium content in steel. The dissolution of steel was made by means of a mixture of hydrochloric and nitric acids. Niobium was precipitated by hydrolysis in the presence of tannin, gelatine and ascorbic acid and then was determined in the form of a coloured complex compound at pH 3. The concentration of niobium in the examined solution cannot exceed 1,6 μg/cm 3 . Standard deviation for niobium content 0,017% Nb is 0,0007% and for 0,100% Nb - 0,0025%. (author)

Decrease in Hydrogen Embrittlement Susceptibility of 10B21 Screws by Bake Aging

Directory of Open Access Journals (Sweden)

Kuan-Jen Chen

2016-08-01

Full Text Available The effects of baking on the mechanical properties and fracture characteristics of low-carbon boron (10B21 steel screws were investigated. Fracture torque tests and hydrogen content analysis were performed on baked screws to evaluate hydrogen embrittlement (HE susceptibility. The diffusible hydrogen content within 10B21 steel dominated the fracture behavior of the screws. The fracture torque of 10B21 screws baked for a long duration was affected by released hydrogen. Secondary ion mass spectroscopy (SIMS result showed that hydrogen content decreased with increasing baking duration, and thus the HE susceptibility of 10B21 screws improved. Diffusible hydrogen promoted crack propagation in high-stress region. The HE of 10B21 screws can be prevented by long-duration baking.

Investigation of Au9+ swift heavy ion irradiation on CdS/CuInSe2 thin films

International Nuclear Information System (INIS)

Joshi, Rajesh A.; Taur, Vidya S.; Singh, Fouran; Sharma, Ramphal

2013-01-01

In the present manuscript we report about the preparation of CdS/CuInSe 2 heterojunction thin films by chemical ion exchange method and investigation of 120 MeV Au 9+ swift heavy ions (SHI) irradiation effect on its physicochemical as well as optoelectronic properties. These pristine (as grown) samples are irradiated with 120 MeV Au 9+ SHI of 5×10 11 and 5×10 12 ions/cm 2 fluencies and later on characterized for structural, compositional, morphological, optical and I–V characteristics. X-ray diffraction (XRD) pattern obtained from pristine and irradiated films shows considerable modifications in peak intensity as well as rising of some new peaks, corresponding to In 2 Se 3 , Cu 3 Se 2 and CuIn 2 Se 3 materials. Transmission electron microscope (TEM) images show decrease in grain size upon increase in irradiation ion fluencies, which is also supported from the observation of random and uneven distribution of nano-grains as confirmed through scanning electron microscope (SEM) images. Presence of Cd, Cu, In, S and Se in energy dispersive X-ray spectrum analysis (EDAX) confirms the expected and observed elemental composition in thin films, the absorbance peaks are related to band to band transitions and spin orbit splitting while energy band gap is observed to increase from 1.36 for pristine to 1.53 eV for SHI irradiated thin films and I–V characteristics under illumination to 100 mW/cm 2 light source shows enhancement in conversion efficiency from 0.26 to 1.59% upon irradiation. - Highlights: • Nanostructured CdS/CuInSe 2 can be grown by chemical ion exchange method. • Physicochemical and optoelectronic properties can be modified by 120 MeV Au 9+ SHI Irradiation. • Solar energy conversion efficiency improved from 0.26 to 1.59% in CdS/CuInSe 2 upon irradiation

IL-10 and IL-27 producing dendritic cells capable of enhancing IL-10 production of T cells are induced in oral tolerance.

Science.gov (United States)

Shiokawa, Aya; Tanabe, Kosuke; Tsuji, Noriko M; Sato, Ryuichiro; Hachimura, Satoshi

2009-06-30

Oral tolerance is a key feature of intestinal immunity, generating systemic tolerance to ingested antigens (Ag). Dendritic cells (DC) have been revealed as important immune regulators, however, the precise role of DC in oral tolerance induction remains unclear. We investigated the characteristics of DC in spleen, mesenteric lymph node (MLN), and Peyer's patch (PP) after oral Ag administration in a TCR-transgenic mouse model. DC from PP and MLN of tolerized mice induced IL-10 production but not Foxp3 expression in cocultured T cells. IL-10 production was markedly increased after 5-7-day Ag administration especially in PP DC. On the other hand, IL-27 production was increased after 2-5-day Ag administration. CD11b(+) DC, which increased after ingestion of Ag, prominently expressed IL-10 and IL-27 compared with CD11b(-) DC. These results suggest that IL-10 and IL-27 producing DC are increased by interaction with antigen specific T cells in PP, and these DC act as an inducer of IL-10 producing T cells in oral tolerance.

Analysis of the relationship between single nucleotide polymorphism of the CD209, IL-10, IL-28 and CCR5 D32 genes with the human predisposition to developing tick-borne encephalitis