The effect of thermal treatment on corrosion properties of 0Kh15N16M3B stainless steel tested in the N2O4 boiling medium

International Nuclear Information System (INIS)

Kamenev, A.Ya.; Kopets, Z.V.; Mel'nikova, N.N.; Dergaj, A.M.; Fedyushin, E.E.

1985-01-01

The experimental data on the effect of thermal treatment on corrosion properties of stainless steel 00Kh16n15m3b tested in the N 2 O 4 boiling medium at 8.0 MPa and 433 K are presented. The electron microscope data on steel microstructure after different heat treatments and phase composition of oxide films emerging at corrosion test are given. It is shown, that the rise of the heat treatment temperature from 823 up to 1023 K increases total corrosion of 00Kh16n15m3b steel under given test conditions and practically does't affect intercrystalline corrosion. Developed oxide layers are of deposited nature and doesn't affect markedly the rate of progress of the corrosive processes. Taking into account high chromium volatility in vacuum one can assume that at the initial stages of the coolant effect, the process of depletion of steel surface by chromium durng heat treatment affects markedly steel corrosion stability

Peculiarities of welding procedure for the 05Kh12K14N5M5T-VD maraging stainless steel with strength higher 1500 MPa

International Nuclear Information System (INIS)

Pustovit, A.I.

1980-01-01

The effect of welding procedure of 05Kh12K14N5M5T-VD stainless steel on the properties of its welded joints is investigated. A new procedure of welding for pressure vessels made of this steel using Sv-03Kh15K14N5M3T-EL welding wire is suggested [ru

Neutron diffraction study of a nitrogen martensitic steel 0Kh16N4AB under load

Czech Academy of Sciences Publication Activity Database

Sumin, V. V.; Papushkin, I.V.; Bannykh, O.A.; Blinov, V.M.; Lukáš, Petr

2008-01-01

Roč. 105, č. 1 (2008), s. 88-91 ISSN 0031-918X Institutional research plan: CEZ:AV0Z10480505 Keywords : steel 0Kh16N4AB * neutron diffraction * FSD Subject RIV: BG - Nuclear, Atomic and Molecular Physics , Colliders Impact factor: 0.412, year: 2008

Mechanical properties and kinetics of bainite transformation in the 35KhN3MFA and 25KhN3MFA steels

International Nuclear Information System (INIS)

Korotushenko, G.V.; Grigorkin, V.I.; Kozlov, V.I.; Sandomirskij, M.M.; Krivonosova, L.F.

1978-01-01

The mechanical properties and phase composition of the 25KhN3M A and 25KhN3M A bainitic steels have been investigated under austenization temperature varying from 870 to 1180 deg C and quenching cooling rate varying from 1 to 18x10 3 deg/min. Roentgen and quantitative phase analyses were employed. When bainitic steels are subjected to quenching by cooling with slow rate, their structure reveals b.c.c.-bainite with carbon content below the steel average, tetragonal martensite with a higher carbon content, carbon-rich residual austenite and carbides. Decreasing quenching cooling rates increase the concentration of tetragonal martensite and residual austenite and correspondingly reduce the concentration of b.c.c.-bainite. This tends to degrade the structural strength of bainitic steels in cores of large-size forged products

Effect of heat treatment and plastic deformation on the structure and the mechanical properties of nitrogen-bearing 04N9Kh2A steel

Science.gov (United States)

Blinov, V. M.; Bannykh, O. A.; Lukin, E. I.; Kostina, M. V.; Blinov, E. V.

2014-11-01

The effect of the conditions of heat treatment and plastic deformation on the structure and the mechanical properties of low-carbon martensitic nickel steel (9 wt % Ni) with an overequilibrium nitrogen content is studied. The limiting strain to failure of 04N9Kh2A steel is found to be 40% at a rolling temperature of 20°C and 80% at a rolling temperature of 900°C. Significant strengthening of the steel (σ0.2 = 1089 MPa) is obtained after rolling at a reduction of 40% at 20°C. The start and final temperatures of the α → γ transformation on heating and those of the γ → α transformation on cooling are determined by dilatometry. The specific features of the formation of the steel structure have been revealed as functions of the annealing and tempering temperatures. Electron-microscopic studies show that, after quenching from 850°C and tempering at 600°C for 1 h, the structure contains packet martensite with thin interlayers of retained austenite between martensite crystals. The strength of the nitrogen-bearing 04N9Kh2A steel after quenching from 850 and 900°C, cooling in water, and subsequent tempering at 500°C for 1 h is significantly higher than that of carboncontaining 0H9 steel used in cryogenic engineering.

Tendency of the 18-8 type corrosion-resistant steel to cracking in automatic building-up of copper and copper base alloys in argon

International Nuclear Information System (INIS)

Abramovich, V.R.; Andronik, V.A.

1978-01-01

Studied was the tendency of the 18-8 type corrosion-resistant steel to cracking during automatic building-up of copper and bronze in argon. The investigation was carried out on the 0kh18n10t steel in argon. It had been established, that the degree of copper penetration into the steel inceases with the increase in the time of the 0Kh18n10t steel contact with liquid copper. Liquid copper and copper base alloys have a detrimental effect on mechanical properties of the steel under external tensile load during intercontant. It is shown that in building-up of copper base alloys on the steel-0Kh18n10t, tendency of the steel to cracking decreases with increase in stiffness of a surfaced weld metal plate and with decrease in building-up energy per unit length. The causes of macrocracking in steel at building-up non-ferrous metals are explained. The technological procedures to avoid cracking are suggested

Corrosion behaviour of stainless steels by internal friction method

International Nuclear Information System (INIS)

Postnikov, V.S.; Kovalevskij, V.I.

1987-01-01

Corrosion of austenite chromium-nickel stainless steels 12 Kh18N9, 12Kh18N9T, 12Kh18N10 and 12Kh18N10T is investigated. Wire samples 0.7...0.8 mm in diameter before tests were subjected to quenching in water from the temperature of 1050...1100 deg C and part of them - to tempering at 650 deg C for 2 h. Pitting corrosion was brought about by different concentration of iron chloride solutions (C FeCl 3 ). Total corrosion has a slight effect on the character of IF (internal friction) variation that increases without the whole test period up to the moment when mechanical strength of the sample

Quality of austenite chrome-nickel steel made by gas-oxygen refining

International Nuclear Information System (INIS)

Fel'dgandler, Eh.G.; Levin, F.L.; Moshkevich, E.A.; Shifrin, Eh.V.; Movshovich, V.S.; Pargamonov, E.A.

1991-01-01

Properties and structure were investigated of austenitic 03Kh18N11 and 08KhN10T steels melted at gas oxygen refining aggregates. It was established that mechanical and corrosion properties of rolling of such steels were in agreement with standard properties of metal of open melting. Sheet 08Kh18N10T steel has the level of strength and plasticity regulated for 12Kh18N10T steel. As steel of 08Kh18N10T holds the complex of high mechanical and corrosion properties, 08Kh18N10T is recommended to be replace by 12Kh18N10T with the aim of decrease of titanium usage and increase of process efficiency

Welding of high-strength stainless steel 03Kh12N10MT for cryogenic engineering

International Nuclear Information System (INIS)

Pustovit, A.I.

1989-01-01

Consideration is being given to weld resistance to cold and hot cracking at 93 and 77K and to mechanical properties of welded joints of high-strength stainless steel 03Kh12N10MT, produced under the fluxes AN-17M, AN-18, AN-26, AN-45, ANF-5, 48-OF-6, ANK-45 and ANK-49 in combination with various welding wires. It is shown that welds on 03Kh12N10MT steel meet the requirements only when using 48-OF-6 or ANK-49 flux. It is noted that impact strength of welds at 77K is sufficiently affected by the volume fraction of non-metallic inclusions in weld metal

Steel corrosion in tributyl phosphate in the presence of water and ethyl mercaptan

International Nuclear Information System (INIS)

Pischik, L.M.; Tsinman, A.I.

1979-01-01

Studied is the corrosion of steels St3, 15Kh5M, 08Kh13, 10Kh14G14N4T, 08Kh18G8N2T, 10Kh17N13M2T in TBP, in mixtures of TBP with ethyl mercaptan (EM) and two-phase systems TBP-water and TBP-water-EM at 50-150 deg. In pure TBP St3 corrosion rate is low even at 150 deg. In the presence of water St 3 strongly corrodes at above 50 deg temperature in organic and water layers and also in gas phase. The steel-08Kh18G8N2T at 90 deg in acid TBP is passive and its corrosion rate is lower than 0.01 mm/year. In identical conditions the resistance of stainless steels increases together with chromium content but in TBP with acid number 100 and above at 150 deg all tested steels including steel-10Kh17N13M2T are slightly resistant. Thus, even in absence of corrosion active additions of EM the mixture of TBP-water at higher temperature is agressive in relation not only to carbon steel but also to stainless steels

Nitrogen-containing superlow-carbon austenitic steel 02Kh25N22AM2

Science.gov (United States)

Fe'ldgandler, É. G.; Svistunova, T. V.; Savkina, L. Ya.; Lapshina, O. B.

1996-02-01

At present the equipment for manufacturing carbamide mineral fertilizers is produced from domestic steel 03Kh17N14M3 having "carbamide quality." Imported equipment also used in the industry is produced from steel of the 25-22-2 (Cr -Ni-Mo) type shipped by various firms, namely, 2RE69 (Sandvik, Sweden), 254SFER (Avesta, Sweden), 2522LCN (VDM, Germany), DM 1.4466 (Germany), and X2CrNiMo 25-22-2 (Dalmine, Italy). The imported steels are used because in some units steel 03Khl7Nl4M3 does not provide the requisite corrosion resistance in an intensified process of carbamide manufacturing. We currently possess domestic high-alloyed steel for producing new and repairing imported equipment operating under the severe conditions of carbamide synthesis. The present paper concerns the structure, mechanical properties, and corrosion resistance of industrially produced steel 02Kh25N22AM2 (ChS-108) and the recommended range of its application.

Heat affected zone structure in welded joints of 15Kh1M1FL, 25Kh2NMFA and 20KhN2MFA steels

International Nuclear Information System (INIS)

Levenberg, N.E.; German, S.I.; Fomina, O.P.; Netesa, E.M.; Tsaryuk, A.K.; Kornienko, T.A.

1983-01-01

Heat affected zone (HAZ) structure of thick-walled, nature joints of 15Kh1M1FL steel for block structure of power reactors and 25Kh2NMFA and 20KhN2MFA steels for rotors - is investigated. Multi-layer arc welding is performed under conditions being created for standard components of turbines. Thermokinetics diagrams of austenite decomposition are built, phase composition and character of the structure forming at HAZ in the process of welding with preheating are studied. It is shown that at HAZ in joints of the steels under consideration in the process of welding with preheating is formed a structure of a grained bainite which is uniform in its structure and phase composition. Small volumes of round and elongated forms consisting of martensite and residual austenite are distributed in α-solid solution of the bainite. The bainite of the HAZ in welded joints possesses high hardness and great stability in the process of tempering

Changes in structure and phase composition of chromium diffusion layer on stainless steels after long annealing

International Nuclear Information System (INIS)

Knyazev, E.V.; Voshedchenko, B.M.; Voskresenskij, Yu.A.

1985-01-01

A study was made on the effect of elevated temperatures UU and long holdings at heat on structure, phase composition and properties of chromium diffusion layer on austenitic chromium-nickel stainless steels 10Kh18N10TVD, 10Kh15N30M4B, 10Kh11N23T3MR, 10Kh21N28V6M3. The following mechanism of processes taking place in diffusion chromium layer is presented. The steady drop of chromium concentrations is observed after diffusion saturation. Chromium redistribution related with system transformation to more equilibrium state and simultaneous decarburization of steel surfaces takes place in diffusion layers of 10Kh15N30M4B and 10Kh21N28V6M3 steels after annealing at different temperatures and holdings at heat. Decarburization of steel surface layers is practically excluded in diffusion layers of 10Kh18N10T-VD and 10Kh11N23T3MR steels. Diffusion chromium-saturated layer stays effective only on 10Kh18N10T-VD and 10Kh11N23T3MR steels on heating up to 1000 deq C with holding up to 250 h

Welding procedure for 06Kh13N7D2 steel

International Nuclear Information System (INIS)

Muromtsev, B.I.; Turkov, I.I.

1990-01-01

Based on the results of investigations into the process strength, mechanical and corrosion properties of 08Kh13N7D2 steel welded joints, the optimal method of its welding and a possibility of applying it for high-strength mounting in nuclear power plants are determined

Corrosion behavior of austenitic steels and their components in niobium-containing chloride melts

Science.gov (United States)

Abramov, A. V.; Polovov, I. B.; Rebrin, O. I.; Volkovich, V. A.; Lisienko, D. G.

2014-02-01

The mechanism of corrosion of austenitic steels 12Kh18N10T, 10Kh17N13M2T, and 03Kh17N14M3 and metals Cr, Fe, Ni, and Mo in a NaCl-KCl-NbCl n ( n = 3.5, Nb content is 5 ± 0.1 wt %) melt at 750°C is studied. The metal and steel corrosion rates under these conditions are determined. The character of material fracture and the mechanisms of material corrosion are found.

Stationary potentials and corrosion of metals and steels in sodium and potassium chloride eutectic melts saturated with hydrogen chloride

International Nuclear Information System (INIS)

Belov, V.N.; Ershova, T.K.; Kochergin, V.P.

1978-01-01

Stationary potentials have been measured at 850 deg C and corrosion rates found gravimetrically for a number of metals and steels in the eutectic NaCl-KCl melt saturated with HCl. Periodic shifts of the stationary potentials towards positive values have been established in the Ti-V-Cr-Fe-Ni, Cu-Zr-Nb-Mo, Ag-Ta-W-Pt systems, with the corrosion rate of metals decreasing in them. The stationary potentials are shown to shift towards positive values in the series: st.08 KP, st.3, Kh17N2, Kh22N6T, Kh13NChG9, 1Kh18N10T, Kh17N13M2T, OKh17N16M3T, Kh23N18, Kh25N16G7, Kh23N28M3D3T, with corrosive resistance in this series increasing

Effect of heat treatment regime on structural lamination in ferritic-austenitic steels

International Nuclear Information System (INIS)

Sizov, R.A.; Zakharova, M.I.; Novikov, I.I.; Bannykh, O.A.

1983-01-01

The effect of preliminary thermal treatment on lamination and viscosity of EhP-53 and KO-3 steels after durable aging at the temperature of 350 is studied. It is shown that preliminary heat treatment considerably affects lamination processes in the result of aging of 0Kh18G8N2T steel. The lowest rate of lamination and higher impact strength after aging at 350 deg C for 4500 hours corresponds to the following heat treatment: 10 hour aging at 650 deg C with cooling in the air, then quenching in water from 950 deg C after aging for 30 min and the following tempering (650 deg C, 5 hours). Unlike the 0Kh18G8N2T steel, lamination parameters of steel 0Kh22N6T practically do not change after the application of heat treatment. Nevertherless, taking into account results of impact strength, it is advisable to have thermal treatment according to the regime: quenching in water at 950 deg C after aging for 30 min

Local corrosion of high alloy steels under biodeposits

International Nuclear Information System (INIS)

Korovyakova, M.D.; Nikitin, V.M.; Speshneva, N.V.

1999-01-01

Impact of the bacteriozenosis different structural-functional state under biodeposits on corrosion resistance of the 12Kh18N10T and Kh18N10T high-alloy steels in the natural seawater is studied. It is shown that saturation of natural micro communities by separate aerobic and facultative-anaerobic bacterial monocultures increases corrosion resistance of these steels by their overgrow with biodeposits [ru

Estimation of structural strength of 38KhN3MFA steel, melted using different methods

International Nuclear Information System (INIS)

Kudrya, A.V.; Mochalov, B.V.; Fadeev, Yu.I.

1982-01-01

Quantity of steel melted by different methods using criteria of fracture mechanics is evaluated. Three technological variants of the 38KhN3MFA steel melting: acid Martin steel prepared by the duplex-process (melt 1); the main Martin steel melting with deoxidation and alloying in a ladle by liquid alloy and treatment with synthetic slag with argon purging after production (melt 2) and its electroslag remelt - ESP process (melt 3) are investigated. The analysis of the investigated melts has revealed that crack resistances of the acid Martin steel is higher than that of other melts at practically similar standard mechanical properties with 0.35 probability at 0.05 significance level in the low-tempered state; in the tempered state the best crack resistance is observed in the ESP main Martin steel. Metal of the main Martin melting has lower crack resistance as compared with other meltings at both strength levels. The results of the work point out the necessity of applying the criteria of fracture mechanics for obtaining an objective evaluation of the steel quality

Effect of preliminary heat treatment on phase transformations and properties of the Kh15N5D2T (VNS-2) steel

International Nuclear Information System (INIS)

Madyanov, S.A.; Voronenko, B.I.; Makhnev, E.S.

1978-01-01

It is shown that preliminary heat treatment has a significant effect on the α→γ transformation kinetics, the quantity of residual austenite, the grain size and mechanical properties of the Kh15N5D2T steel after final heat treatment. The preliminary heat treatment regimes leading to the increase of the quantity of residual austenite and to grain refining increase the work of crack propagation in the finally strengthened state. The optimum properties were obtained after threefold preliminary tempering for 1h at 650 deg C. An approximately constant relation of α- and γ-phases (approximately 50%) is observed at 625 deg C irrespective of the investigated regimes of preliminary heat treatment

Welding of heterogeneous 12Kh2MFSR steels with the Mn-Cr-Si-Ni system

International Nuclear Information System (INIS)

Smirnov, A.N.; Belogolov, E.I.

1978-01-01

The process of welding pipes of the 12Kh2MFSR pearlitic steels and austenitic steels of the Mn-Cr-Si-Ni system was studied. The filler materials were selected, and the working capacity of welded joints was examined in ageing and cyclic heatings. The microhardness of steels was measured, and the ultimate strength of welded joints was determined. The following has been established: the composite joints of steels of the Mn-Cr-Si-Ni system and 12Kh2MFSR steel are advisable to be welded on a coating layer welded by the EhA395/9 electrodes on the surface of a pipe of the 12Kh2MFSR pearlitic steel; this guarantees the sufficient working capacity of welded joints

Effect of smelt aluminium on mechanical properties of steels

International Nuclear Information System (INIS)

Ryabov, V.R.; Dykhno, I.S.; Deev, G.F.; Karikh, V.V.

1987-01-01

Effect of smelt aluminium on mechanical properties of armco-iron and 12 Kh18N10T steel is studied. It is stated that in smelt aluminium and aluminium alloy contact with armco-iron the sample ductility is decreased. Corrosion effect of smelt alluminium on (18Kh15N5AM3) steel in the form of reinforced wire in aluminium-steel KAS-1A composite material is investigted. It is stated in experiment that during smelt alluminium-steel contact interaction of heterogeneous phases takes place

Simulation of Microdamage and Evaluation of Remaining Life of Steam Conduit Components from New-Generation Refractory Steel 10Kh9MF-Sh

Science.gov (United States)

Gladshtein, V. I.

2018-03-01

The effects of microdamage on the remaining life of high-temperature components of steam conduits from high-chromium steel 10Kh9MF-Sh and low-alloy steel 12Kh1M1F are compared. To simulate the microdamage, specimens with a circular notch and different relative diameters are fabricated. Specimens with a notch simulating the highest degree of microdamage and smooth specimens are tested for long-term strength. The coefficient of the remaining life of a conduit is computed for the range of relative damage presenting practical interest.

Corrosion of austenitic steels and their components in vanadium-containing chloride melts

Science.gov (United States)

Abramov, A. V.; Polovov, I. B.; Rebrin, O. I.; Lisienko, D. G.

2014-08-01

The corrosion of austenitic 12Kh18N10T, 10Kh17N13M2T, and 03Kh17N14M3 steels and their components (Cr, Fe, Ni, Mo) in NaCl-KCl-VCl2 melts with 5 wt % V at 750°C is studied. The rates and mechanisms of corrosion of the materials under these conditions are determined. The processes that occur during contact of the metals and steels with vanadium-containing chloride electrolytes are investigated.

Effect of Cr, Ni, and Mo additions on the susceptibility of the 0Kh6n7m7c steel to hot cracking

International Nuclear Information System (INIS)

Tolstykh, L.G.; Pryakhin, A.V.; Popov, A.N.; Usynin, V.F.

1977-01-01

The effect of chromium, molybdenum, and nickel on the tendency of surfacing materials to form hot cracks (Vsub(kp) was studied using the mathematical statistics method. The St3 steel and 38KhN3MFA steel were used in the study. A device facilitating the hot cracking tendency test procedure was developed. It was found that, in the concentration range involved, Ni and Mo produce no effect on Vsub(kp), and Cr enhances it. A new powder wire, PP-OKh7N8M6S, capable of increasing surface material resistance by 1.5-2 times, has been developed

Strain ageing of the 15Kh2MFA steel at 500 and 550 deg C

International Nuclear Information System (INIS)

Maksimovich, G.G.; Azbukin, V.G.; Krylova, R.P.; Tretyak, I.Yu.; Bardachevskaya, T.V.

1978-01-01

The effect of ageing at high temperatures and under high stresses on strength and plasticity of the 15Kh2MFA steel has been studied. The steel was kept at 500 and at 550 deg C for 100, 1000 and 2500 hours without stress and under stress of 0.5 and 0.9 of the long-term strength limit (sigmasub(ls)). Ageing at 500 deg C without stress and under 0.5 sigmasub(ls) changed neither strength nor plasticity of the steel; under 0.9 sigmasub(ls) the strength somewhat decreased. Ageing at 550 deg C for 1000 hours resulted in an appreciable stress drop

Influence of ion implanted helium on deuterium trapping in Kh18N10T stainless steel

International Nuclear Information System (INIS)

Tolstolutskaya, G.D.; Ruzhitskij, V.V.; Kopanets, I.E.

2004-01-01

The results are presented on evolution of distribution profiles and helium and deuterium thermal desorption ion implanted in steel 18Cr10NiTi. Accumulation, trapping, retention and microstructure evolution are studied; effect helium and hydrogen simultaneous implantation on these processes is also studied

Effect of helium ion bombardment on hydrogen behaviour in stainless steel

International Nuclear Information System (INIS)

Guseva, M.I.; Stolyarova, V.G.; Gorbatov, E.A.

1987-01-01

The effect of helium ion bombardment on hydrogen behaviour in 12Kh18N10T stainless steel is investigated. Helium and hydrogen ion bombardment was conducted in the ILU-3 ion accelerator; the fluence and energy made up 10 16 -5x10 17 cm -2 , 30 keV and 10 16 -5x10 18 cm -2 , 10 keV respectively. The method of recoil nuclei was used for determination of helium and hydrogen content. Successive implantation of helium and hydrogen ions into 12Kh18N10T stainless steel results in hydrogen capture by defects formed by helium ions

Effect of melting technique on grain size and heat resistance of the 12Kh1MF steel

International Nuclear Information System (INIS)

Lanskaya, K.A.; Kulikova, L.V.; Butneva, N.I.

1978-01-01

Investigated are the 12Kh1MF steel melted in open-hearth and arc furnaces (deoxidation by aluminium in 1.0 kg/t quantity) and then subjected to electroslag melting. The size of an austenitic grain depends on the residual contents of nitrogen and aluminium in steel. The open-hearth metal subjected to electroslag melting and containing a small quantity of nitrogen (0.006%) and aluminium (0.013%) has coarse austenitic grains and higher heat resistance compared to the steel melted in an arc furnace and also sub ected to electroslag melting. The nitride analysis of steel is carried out

Investigation into the Cyclic Strength of the Bodies of Steam Shutoff Valves from 10Kh9MFB-Sh Steel

Science.gov (United States)

Skorobogatykh, V. N.; Kunavin, S. A.; Prudnikov, D. A.; Shchenkova, I. A.; Bazhenov, A. M.; Zadoinyi, V. A.; Starkovskii, G. L.

2018-02-01

Steam shutoff valves are operated under complex loading conditions at thermal and nuclear power stations. In addition to exposure to high temperature and stresses resulting in fatigue, these valves are subjected to cyclic loads in heating-up-cooling down, opening-closing, etc. cycles. The number of these cycles to be specified in designing the valves should not exceed the maximum allowable value. Hence, the problem of cyclic failure rate of steam shutoff valve bodies is critical. This paper continues the previous publications about properties of the construction material for steam shutoff valve bodies (grade 10Kh9MFB-Sh steel) produced by electroslag melting and gives the results of investigation into the cyclic strength of this material. Fatigue curves for the steal used for manufacturing steam shutoff valve bodies are presented. The experimental data are compared with the calculated fatigue curves plotted using the procedures outlined in PNAE G-002-986 and RD 10-249-98. It is confirmed that these procedures may be used in designing valve bodies from 10Kh9MFB-Sh steel. The effect of the cyclic damage after preliminary cyclic loading of the specimens according to the prescribed load conditions on the high-temperature strength of the steel is examined. The influence of cyclic failure rate on the long-term strength was investigated using cylindrical specimens with a smooth working section in the as-made conditions and after two regimes of preliminary cyclic loading (training) at a working temperature of 570°C and the number of load cycles exceeding the design value, which was 2 × 103 cycles. The experiments corroborated that the material (10Kh9MFB-Sh steel) of the body manufactured by the method of electroslag melting had high resistance to cyclic failure rate. No effect of cyclic damages in the metal of the investigated specimens on the high-temperature strength has been found.

Tribocorrosion behaviour of 08CH18N10T steel

International Nuclear Information System (INIS)

Kubecka, P.; Tvrdy, M.; Wenger, F.; Ponthiaux, P.

2000-01-01

Tribocorrosion of the 08CH18N10T austenitic stainless steel in a potassium sulphate solution was investigated with the help of pin-on-disk tribometer and polarisation curves method. The results indicate the occurrence of synergetic interactions between electrochemical and mechanical conditions: the damaging of the passive film by friction was pointed out, leading to an increase in the dissolution rate of the metal and simultaneously, the occurrence of electrochemical reactions (gas evolution, dissolution, passivation) was found to modify the tribological conditions (friction coefficient). (author)

Improving composition of protective coatings for steel casting

International Nuclear Information System (INIS)

Kuz'kina, N.N.; Pegov, V.G.; Bogatenkov, V.F.; Shub, L.G.; Raspopova, N.A.

1983-01-01

A radically new fuel-free slag-forming mixture used as protective coating for steel casting is introduced. The lack of combustible powders precludes explosion and fire Lazard in mixture preparation. Usage of the new mixture in stainless steel casting of Kh18N10T type permitted to improve the ingot surface quality and reduce spoilage from 1.16 to 0.66%

Corrosion of chromium, nickel, titanium and steels in solutions of sodium and ammonium thiosulfates

International Nuclear Information System (INIS)

Grebenshchikova, S.V.; Kochergin, V.P.; Doronina, I.V.

1983-01-01

Results of gravimetric determinatiion of average rate of chromium, nickel, titatnium and steels 12Kh18N10T and VSt.3 corrosion rate in solutions 50 mass.% (NH 4 ) 2 S 2 O 3 and Na 2 S 2 O 3 in the air and nitrogen atmosphere at 333 K have been generalized. Anodic polarization curves are recorded and stationary potentials of metals and steels under the conditions are measured. It is shown that in (NH 4 ) 2 S 2 O 3 solution the rate of metal and steels corrosion is higher than in Na 2 S 2 O 3 solution indepenent of the nature of gaseous medium contacting with solution. In the series Ni → VSt.3 → 12Kh18N10T → VT1 → chromium in (NH 4 ) 2 S 2 O 3 and Na 2 S 2 O 3 solutions at 333 K corrosion resistance increases. Chromium, titanium and chromium-nickel steel 12Kh18N10T possess a high corrosion resistance

Parametrical limits of SCC-susceptibility of austenitic and austenitic-ferritic Cr-Ni steels

International Nuclear Information System (INIS)

Starosvetskij, D.I.; Baru, R.L.; Bondarenko, A.I.; Bogoyavlenskij, V.L.; Timonin, V.A.

1990-01-01

Comparative investigations into corrosion cracking (CC) of austenitic (12Kh18N10T) and austenitic-ferritic (08Kh22N6T) chromium-nickel steels are performed for various chloride media in a wide range of chloride concentrations and temperatures. It is shown that the ratio between steels in terms of their CC-susceptibility is not definite and can undergo a reversal depending on parameters of medium, level and conditions of loading. Differences in mechanisms of corrosion cracking of austenitic and austenitic-ferritic steels are established

Heat treatment effect on impact strength of 40Kh steel

International Nuclear Information System (INIS)

Golubev, V.K.; Novikov, S.A.; Sobolev, Yu.S.; Yukina, N.A.

1984-01-01

The paper presents results of studies on the effect of heat treatment on strength and pattern of 40Kh steel impact failure. Loading levels corresponding to macroscopic spalling microdamage initiation in the material are determined for three initial states. Metallographic study on the spalling failure pattern for 40Kh steel in different initial states and data on microhardness measurement are presented

Joint formation of dissimilar steels in pressure welding with superposition of ultrasonic oscillations

Energy Technology Data Exchange (ETDEWEB)

Surovtsev, A P; Golovanenko, S A; Sukhanov, V E; Kazantsev, V F

1983-12-01

Investigation results of kinetics and quality of carbon steel joints with the steel 12Kh18N10T, obtained by pressure welding with superposition of ultrasonic oscillations with the frequency 16.5-18.0 kHz are given. The effect of ultrasonic oscillations on the process of physical contact development of the surfaces welded, formation of microstructure and impact viscosity of the compound, is shown.

Corrosion cracking of 03N18K1M3TYu and 02N12Kh5M3 maraging steels in chloride solutions

Energy Technology Data Exchange (ETDEWEB)

Pavlov, V.N.; Chumalo, G.V.; Vereshchagin, A.N.; Melekhov, R.K.

1987-07-01

The authors investigate the electrochemical behavior in 0.5% NaCl solution and 42% MgCl/sub 2/ solution and the tendency toward corrosion cracking was determined in boiling 0.5% chloride solution of the cobalt-containing maraging steels in the title. Weld specimens and specimens of the base metal of 03N18K1M3TYu steel were tested in 3% NaCl solution for resistance to corrosion cracking. Additional investigations were made of specimens of that steel with previously created fatigue cracks of the base metal and the weld specimens in 3% NaCl solutions, since that steel is a promising material for structures operating in sea water and low concentration chloride solutions.

Irradiation and annealing behavior of 15Kh2MFA reactor pressure vessel steel

International Nuclear Information System (INIS)

Popp, K.; Bergmann, U.; Bergner, F.; Hampe, E.; Leonhardt, W.D.; Schuetzler, H.P.; Viehrig, H.W.

1992-01-01

This work deals with the mechanical properties of RPV steels used WWER-440. The materials under investigation were a forging (base metal 15Kh2MFA) and the corresponding weld. Charpy V-notch specimens and tensile test specimens were irradiated in the WWER-2 Rheinsberg at about 270 C up to the two neutron fluence levels of 4 x 10 18 and 5 x 10 19 n/cm 2 (E>1MeV). Post-irradiation annealing heat treatments were performed, among others a 475 C/152 h treatment of technical interest. (orig.)

Effect of nonmetallic inclusions on anisotropy of ductility in 35KhN3MFA steel forgings

International Nuclear Information System (INIS)

Shtremel', M.A.; Yavojskij, V.I.; Volkov, V.A.; Chursin, G.M.; Chukhlov, V.I.; Fetisov, G.I.; Mochalin, N.K.; Smol'yaninov, L.V.

1980-01-01

Characteristics of nonmetaltic inclusions and anizotropy of ductility and of impuct strength of forgings of the 35KhN3MFA steel are compared at different variants of melting and outer-furnace treatment. It is shown that method of melting rugulates anisotropy of ductility primarily through deformability of large inclusions during forging. Deformability of inclusions considerably changes due to introduction of silicocalcium in iron mold [ru

Preliminary heat treatment of 4KhM2Fch die steel

International Nuclear Information System (INIS)

Leonidov, V.M.; Berezkin, Y.A.; Nikitenko, E.V.

1986-01-01

To improve the machinability and preparation of the structure for hardening, die steels are given a preliminary treatment which provides a reduction in hardness as a result of separation in the structure of the carbide and ferrite phases, coagulation of the carbides, and acquisition by them of a granular form and also the obtaining of fine grains and a uniform distribution of the structural constituents. The microstructure was evaluated after etching in 4% nital on an MIM-8M microscope. The 4KhM2Fch steel was given a preliminary heat treatment of normalize and anneal. It was concluded that for 4KhM2Fch steel a preliminary heat treatment of normalizing from 950 0 C with a hold of 1.5-2 h, annealing at 750-760 0 C with a hold of 2-3 h, cooling to the isothermal temperature of 670-680 0 C with a hold of 3-4 h, and further air cooling is recommended. The structure after such a heat is granular pearlite with a rating 1-2 and a hardness of 220-250 HB

Effect of silicon on the structure, tribological behaviour, and mechanical properties of nitrogen-containing chromium-manganese austenitic steels

International Nuclear Information System (INIS)

Korshunov, L.G.; Chernenko, N.L.; Gojkhenberg, Yu.N.

2003-01-01

The effect of silicon in quantity of 3.5-4.5 mass. % on tribological behaviour is studied for nitrogen-bearing (0.20-0.52 mass. % of nitrogen) chromium-manganese austenitic steels (10Kh15G23S4A0.20, 10Kh16G17N3S4A0.30, 10Kh19G20NS4A0.50, 12Kh19G19NS2A0.50, 10Kh18G19A0.50, 08Kh16G8N10S4A0.18). Mechanical properties and corrosion resistance of the steels are determined. Using metallographic, x-ray diffraction and electron microscopical methods a study is made into structural transformations running in the steels considered under friction and static tension. It is shown that additional silicon alloying of nitrogen-bearing chromium-manganese austenitic steels results in an essential increase of adhesion wear resistance of the materials on retention of low friction coefficient (f=0.25-0.33). A strong silicon effect on steel tribological behaviour is related with planar slip activation and with an increase of austenite strength and heat resistance [ru

Influence of sulphur and phosphorus impurities on ductility of 25Kh2NMFA steel during forging

International Nuclear Information System (INIS)

Onishchenko, A.K.

1989-01-01

Using cylindrical samples of the 25Kh2NMFA steel with sulfur and phosphorus content in the range of 0.001-0.030%, tensile test with the rate of deformation 10 -3 s -1 at the temperatures of 800-1200 deg C has been conducted. Analysis of fracture foci and plasticity diagrams has shown, that to ensure ductility during forging and high mechanical properties, the content of sulfur and phosphorus impurities in the 25Kh2NMFA steel must not exceed 0.015%

Topic 1. Steels for light water reactor pressure vessels

International Nuclear Information System (INIS)

Brumovsky, M.; Brynda, J.; Kepka, M.; Barackova, L.; Vacek, M.; Havel, S.; Cukr, B.; Protiva, K.; Petrman, I.; Tvrdy, M.; Hyspecka, L.; Mazanec, K.; Kupca, L.; Brezina, M.

1980-01-01

Part 1 of the Proceedings consists of papers on the criteria for the selection and comparison of the properties of steel for pressure vessels and on the metallurgy of the said steels, the selection of suitable material for internal tubing systems, the manufacture of high-alloy steels for WWER components, the mechanical and metallurgical properties of steel 22K for WWER 440 pressure components, and of steel 10MnNi2Mo for the WWER primary coolant circuit, and the metallographic assessment of steel 0Kh18N10T. (J.P.)

Optimal control of conditions of deformation during rolling the bar alloy from alloy steel

International Nuclear Information System (INIS)

Inatovich, Yu.V.; Shilov, V.A.; Shvarts, D.L.; Kudelin, S.P.

2001-01-01

A complex of programs for determining the optimal gaps between rollers during rolling of simple merchant sections of alloy steels of a wide brand assortment (12KhN3A, Kh17N2, Kh18N10T) was elaborated. Experience in calculations made according to the programs suggests advisability of their use in the automated design systems for roller calibration and for adjustment of section mills [ru

Effect of nickel and MnS inclusions in the metal on the pitting corrosion of low-carbon stainless steels

International Nuclear Information System (INIS)

Frejman, L.I.; Nguen, The Dong; Volkov, D.E.; Konnov, Yu.P.

1986-01-01

The resistance to pitting corrosion of steels on the 03Kh17-03Kh18 base containing up to 20 % Ni at different levels of S and Mn impurities contamination is investigated. It is shown that up to 50 % of nickel introduced into ordinary steels with 5-6 % Ni is spent to compensate the resistance decrease caused by MnS inclusions. Full compensation is not attained even in the 10-20 %. Ni range in which nickel practically does not affect the resistance of neither ordinary, nor pure (without MnS) steels. Titanium introduction into ordinary steel on the Kh22N6 base permits to surpass the level of 03Kh17N3 pure steel resistance and attain the level of 03Kh17N6 pure steel almost by all characteristics (including passivated characteristics in sulfuric acid) besides pitting repassivity. In this property pure steels with Ni >or approx. 3 % surpass even the molybdenum containing 03Kh21NbM2T ordinary steel though they by far concede by passivation in sulfuric acid

Chromium surface alloying of structural steels during laser treatment

International Nuclear Information System (INIS)

Kurov, I.E.; Nagornykh, S.N.; Sivukhin, G.A.; Solenov, S.V.

1987-01-01

Results of matrix alloying from the surface layer and creation of considerably increased chromium concentration in the depth which permits to increase the efficiency of laser treatment of steels (12Kh18N10T and 38KhN3M) in the process of their further mechanical polishing, are presented. The treatment was realized by continuous CO 2 -laser at different power densities and scanning rates are presented. A model describing the creation of anomalous distributions of the alloying element in steels is plotted

Inhibitor effect on corrosion of titanium alloys in muriatic solutions of titanium-magnesium production

International Nuclear Information System (INIS)

Dobrunov, Yu.V.; Volynskij, V.V.; Kolobov, G.A.; Kuznetsov, S.I.

1977-01-01

Corrosion tests of titanium alloys VTI-0, OT4, VT5-1 and steel Kh18N1OT in 10% and 18% HCl with additions of carnallite at 40 deg C have been carried out. It has been established that titanium alloys in 10% and 18% HCl containing 5 and 10% carnallite are sufficiently corrosion resistant in the presence of 0.1-1% FeCl or HNO 3 and can be used for manufacturing the equipment of recirculation gas scrubbers. Steel Kh18N10T is unstable in all the media tested. It is subjected to intensive pitting. Specimens of steel Kh18N10T have also revealed edge cracking

Effect of zirconium on the structure and phase composition of steel 03Kh8SYu

International Nuclear Information System (INIS)

Tarzhumanova, V.A.; Ryabchenkov, A.V.; Shatunova, A.V.; Yoganova, S.A.

1986-01-01

Previously, the authors determined the optimum zirconium content providing retention of a fine-grained structure for steel 03Kh8SYu during high-temperature heating. It was suggested that this was caused by separation in the steel of intermetallic phase Fe 3 Zr. This paper presents results of further studies in this direction. X-ray analysis results for the anodic residues of the steels are presented. It can be seen that in steel without zirconium, carbides of the type M 23 C 6 and M 7 C 3 and aluminum nitride are present. On adding 0.05% Zr, zirconium nitride forms in addition to the existing aluminum nitride and carbides of the type M 7 C 3 . The authors also investigated the effect of zirconium on the tendency of the steel toward grain growth at higher temperature; they studied the structure of steel 03Kh8SYu with 0.61% Zr after soaking specimens for 100 h at 950-1100 C. Results are presented

The permeation behavior of deuterium through 1Cr18Ni9Ti stainless steel with TiN+TiC-TiN multiple films

International Nuclear Information System (INIS)

Xiong, Y.; Song, J.; Luo, D.; Lei, Q.; Chen, C.

2015-01-01

The prevention of tritium losses via permeation through structure components is an important issue in fusion technology. The production of thin layers on materials with low diffusivity and/or low surface recombination constants (so-called permeation barriers) seems to be the most practical method to reduce or hinder the permeation of tritium through materials. TiN+TiC+TiN multiple films are deposited on the surface of 1Cr18Ni9Ti stainless steel by ion-beam assisted deposition technology. The characteristics of films are tested by XPS ASEM and XRD, which shows that the film are compact and uniform with a thickness of about 15 μm, and have a good adherence with the substrate below 773 K. The diffraction peaks in the XRD patterns for TiC and TiN are broadened, implying that the multiple films are deposited on the surface of 1Cr18Ni9Ti stainless steel. Meanwhile, the C-H bonded CH 4 -appears in the infrared spectra of multiple films, suggesting that the CH 4 - is in a static state, so hydrogen atom cannot migrate from the site bonded with carbon to a neighboring site. The measured deuterium permeability in 1Cr18Ni9Ti stainless steel coated with multiple films is 2-3 orders of magnitude lower than that of pure 1Cr18Ni9Ti stainless steel substrate from 473 K to 773 K. However, this barrier is partly destroyed above 773 K

Successive carbon- and boron saturation of KhVG steel in powder mixtures

Energy Technology Data Exchange (ETDEWEB)

Alimov, Yu A; Gordienko, S I

1975-01-01

Method of successive saturation of KhVG steel with carbon and boron in powder mixtures is described. After carbonization of steel in a charcoal carburator at 930 deg C during 3 hrs a domain of equiaxial large grains is formed there the latter representing carbides of Fe/sub 3/C and (Fe, M)/sub 3/C. The increase of duration of carbonization up to 5 hrs and above results in formation of a cement grid greatly impairing the mechanical properties of the metal. Carbonization is followed by borating in powdered technical boron carbide at 900 deg C for 4 hrs which ensures formation on the sample surface of a borated layer with depth up to 65 mkm covering the carbonized zone. As followed from metallographic and x-ray structural analysis, the borated layer consists of boride needles with complex composition (Fe, Cr, Mn)B. Oil hardening of carbonized KhVG steel from 850 deg C and low-temperature tempering at 180 deg C for 1 hr results in formation in the main metal of martensite-carbide structure and, respectively, in the decrease of the microhardness gradient between the diffusion layers, as compared with borated KhVG steel. Operation tests of strengthened matrices of preforming machines under the conditions of application of dynamic pressing forces up to 1500 kg Fce/cm/sup 2/ demonstrated that the cyclical strength of carboborated coverings is 2.0-3.0 times higher than that of borated ones. The method of carboborating is recommended for strengthening the details of stamp and press tools.

Fouling and biocorrosion of a high-alloy steel in the Golden Horn bay

International Nuclear Information System (INIS)

Koryakova, M.D.; Nikitin, V.M.; Suponina, A.P.; Kharchenko, U.V.; Zvyagintsev, A.Yu.

2002-01-01

The studies on the effect of contamination of the Golden Horn bay waters (the Peter the Great Bay in the Japanese Sea) on formation of the community of the bacterio- and macrofouling and corrosion resistance of the Kh18N10T high-alloy steel are continued. The dissolved and chemically absorbed oxygen, pH, saprophytes, oil-oxidizing, sulfate-reducing bacteria and heavy metals are among the medium indicators, characterizing the level of pollution of the regions of the samples testing. It is shown, that the obtained experimental data extend our understanding of the dependent effect of three factors: the sea medium → fouling → corrosion resistance of the Kh18N10T high-alloy steel [ru

Influence of quantity of non-martensite products of transformation on resistance to fracture of improving structural steel

International Nuclear Information System (INIS)

Gulyaev, A.P.; Golovanenko, Yu.S.; Zikeev, V.N.

1978-01-01

18KhNMFA, low-carbon, alloyed steel and 42KhMFA medium-carbon, alloyed steel have been examined. For the purpose of obtaining different structures in hardening the steel, different cooling rates, different temperatures and isothermal holding times are applied. The following has been shown: on tempering to the same hardness (HV 300), the presence of non-martensite structures in hardened state does not practically influence the standard mechanical properties of steel (sigmasub(B), sigmasub(0.2), delta, PSI). The resistance of steel to the brittle failure is enhanced by the uniform, fine-disperse distribution of the carbide phase in the structure of lower bainite (up to 80 % bainite in martensite for 42KhMF steel to be improved), as well as strongly fragmented packages of rack martensite-bainite (up to 50 % lower bainite in martensite of 18KhNMFA steel). The formation of the upper bainite in the structure of the hardened steels 18KhNMFA and 42KhMF results on tempering in the formation of coarse, non-uniform, branched carbide inclusions, and this, in its turn, leads to raising the cold-shortness threshold and to lowering the amount of work as required for propagation of a crack. The presence of ferritic-pearlitic structures in the structural steels hardened to martensite and bainite results in reducing the resistance of steel to the brittle failure; the presence of every 10 % ferritic-pearlitic component in martensite of the structural steels 18KhNMFA and 42KhMFA to be thermally improved, raises T 50 by 8 deg and 20 deg C, respectively

Hardening and stress relaxation during repeated heating of 15Kh2MFA and 15Kh2NMFA steels welded joints

International Nuclear Information System (INIS)

Zubchenko, A.S.; Suslova, E.A.

1986-01-01

Results of investigation of temperature-time conditions of hardening of welded joints of 15Kh2MFA and 15Kh2NMFA steels and their relaxation resistance, effect of metal structure of imitated heat affected zone (HAZ) on intensity of precipitation hardening at repeated heating are presented as well as the results of the process of relaxation of residual stresses at welded joints samples heating carried out by automatic welding under the flux with the use of adding materials and technology of manufacturing of vessels of WWER-440 and WWER-1000 reactors. Peculiarities of the hardening at repeated heating of the HAZ metal imitated at these steels. Precipitation hardening of overheated 15Kh2MFA steel is connected with precipitations at repeated heating of carbides of the M 7 C 3 , M 3 C and VC type. Stress relaxation in welded joints runs more intensively at the initial stage of repeated heating, i.e. during the same period of the process of dispersed carbide precipitations

Effect of the isothermal transformation temperature on the fine structure of steel-12Kh1MF

International Nuclear Information System (INIS)

Mints, I.I.; Berezina, T.G.; Lanskaya, K.A.

1976-01-01

For detailed analysis of bainite and pearlite in steel 12Kh1MF, homogeneous structures were obtained by isothermal annealing at 350, 450, 500, and 650 0 for 1 h. Isothermal transformation of austenite leads to the formation of bainite at 350-500 0 and pearlite at 650 0 . The austenitizing temperature was 980 0 for both types of samples, with holding for 20 min. For comparison, the plates were quenched from 980 0 and 1050 0 in ice-cold brine. The investigation was conducted with use of light and electron microscopes and x-ray analysis. The long-term strength was also determined. Isothermal treatment of steel 12Kh1MF at 350-500 0 C leads to the formation of a structure consisting of upper and lower bainite. At 500 0 the structure consists primarily of upper bainite, and at 350 0 of lower bainite. With tempering of the steel with a structure of upper and lower bainite at 730 0 for 3 h the dislocations undergo redistribution of the polygonization type within ferrite needles, with development of a cellular substructure. The acicular structure of the matrix is retained in this case. The density and evenness of the distribution of carbides is higher in upper bainite than in lower bainite. Steel 12Kh1MF with a structure of upper bainite is more susceptible to recrystallization as compared with a structure of lower bainite, which is responsible for the higher heat resistance of the latter

Effect of hydrostatic pressure on phase transformations in Kh17N8 steel during deformation

International Nuclear Information System (INIS)

Eshchenko, R.N.; Teplov, V.A.

1984-01-01

The phase composition and structure of Kh17N8 steel strained to different degrees under atmospheric pressure and 1700 MPa are investigated. It has been found that deformation at 1700 MPa causes α and epsilon-martensite formation, the same deformation under atmospheric pressure - only α-martensite formation. The amount of the formed α-martensite is not changed with application of hydrostatic pressure. Electron-microscopic observations have shown that the dispersion of α-martensite formed under pressure is higher than in the absence of pressure; no interconnection in formation of α and epsilon-martensite in samples strained under pressure has been observed

Structure, mechanical and corrosion properties of powdered stainless steel Kh13

International Nuclear Information System (INIS)

Radomysel'skij, I.D.; Napara-Volgina, S.G.; Orlova, L.N.; Apininskaya, L.M.

1982-01-01

Structure, mechanical and corrosion properties are studied for compact powdered stainless steel, Grade Kh13, produced from prealloyed powder and a mixture of chromium and iron powders by hot vacuum pressing (HVP) following four schemes: HVP of unsintered billets; HVP of presintered billets; HVP of unsintered billets followed by diffusion annealing; HVP of sintered billets followed by diffusion annealing. Analysis of the structure, mechanical and corrosion properties of Kh13 steel produced according to the four schemes confirmed that production of this steel by the HVP method without presintering of porous billets and diffusion annealing of compact stampings is possible only when prealloyed powder of particular composition is used as a starting material

Electroplastic drawing of stainless steels

International Nuclear Information System (INIS)

Troitskij, O.A.; Spitsyn, V.I.; Sokolov, N.V.; Ryzhkov, V.G.

1977-01-01

Effect of electroplastic drawing on mechanical, magnetic and electrical properties of wire of 12Kh18N10T and Kh13N13M2 steels was studied. Pulse, direct and alternating currents were used. Direct and alternating current densities were 400 A/mm 2 , mean density of pulse current was 200 A/mm 2 . The investigations have shown that the current density increase results in decreasing the wire strengthening intensity though in increasing plastic properties. As a result of electroplastic drawing the growth of magnetic characteristics of wire occurs

Plasticity of low carbon stainless steels

International Nuclear Information System (INIS)

Bulat, S.I.; Fel'dgandler, Eh.G.; Kareva, E.N.

1975-01-01

In the temperature range 800-1200 0 C and with strain rates of from 10 -3 to 3 s -1 , austenitic (000Kh18N12) and austenitic-ferrite (000Kh26N6) very low carbon stainless steels containing 0.02-0.03% C exhibit no higher resilience than corresponding ordinary steels containing 0.10-0.12% C. However, the plasticity of such steels (particularly two-phase steels) at 900-1100 0 C is appreciably inferior owing to the development of intergranular brittle fracture. Pressure treatment preceded by partial cooling of the surface to 850 0 C yields rolled and forged products with acceptable indices but is inconvenient technically. At the Zlatoustovsk and Ashin metallurgical plants successful tests have been performed involving the forging and rolling of such steels heated to 1280-1300 0 C without partial cooling; it was necessary to improve the killing conditions, correct the chemical composition (increasing the proportion of ferrite) and take measures against heat loss. (author)

Experimental verification of the statistical theories of scaling factor effect in fatigue fracture of steel

International Nuclear Information System (INIS)

Svistun, R.P.; Babej, Yu.I.; Tkachenko, N.N.

1976-01-01

Statistical theories of the scale effect in the fatigue failure of 40KH18N9T, 10 and 20 steels have been verified. The theories are shown to be not invariably suitable for a satisfactory exlanation of the fatigue strength of the samples with respect to their dimensions. One of the main reasons for displaying the scale effect in the process of steel fatigue is the sample self-heating, i.e. a temperature factor which in many cases overlaps a statistical one

Experimental verification of the statistical theories of scaling factor effect in fatigue fracture of steel

Energy Technology Data Exchange (ETDEWEB)

Svistun, R P; Babei, Yu I; Tkachenko, N N [AN Ukrainskoj SSR, Lvov. Fiziko-Mekhanicheskij Inst.; L' vovskij Lesotekhnicheskij Inst. (Ukrainian SSR))

1976-01-01

Statistical theories of the scale effect in the fatigue failure of 40KH18N9T, 10 and 20 steels have been verified. The theories are shown to be not invariably suitable for a satisfactory exlanation of the fatigue strength of the samples with respect to their dimensions. One of the main reasons for displaying the scale effect in the process of steel fatigue is the sample self-heating, i.e. a temperature factor which in many cases overlaps a statistical one.

On the nature of anomalies in temperature dependence of the OKh18N1OT steel yield strength after thermal cycling in the low temperature range

International Nuclear Information System (INIS)

Medvedev, E.M.; Lavrent'ev, F.F.; Kurmanova, T.N.

1978-01-01

Investigated were structural transformations in 0Kh18N10T steel as a result of heating and cooling and of deformation within the range of temperatures between 300 and 77 K, the quantity relationships between the said transformations and the variation of the yield limit with the temperature. The studies were conducted by metallography and mechanical test methods. It was shown that an increase in the number of heating and cooling cycles correlates with a loss in strength of the steel while deformation at 77 K. This anomaly in the temperature relationship of the yield limit is related to the appearance in the course of deformation of α-martensite with a BCC lattice. Deformation at 300 K increases the amount ea of epsilon-martensite, a decrses the effectve size of grain and, in consequence, increases the yield limit. The relationship between the yield limit and the grain size at the temperature of 300 K is described adequately by the Hall-Petch equation

Corrosion resistance of heat exchange equipment in hydrotreating Orenburg Condensate

International Nuclear Information System (INIS)

Teslya, B.M.; Burlov, V.V.; Parputs, I.V.; Parputs, T.P.

1986-01-01

The authors study the corrosion resistance of materials of construction and select appropriate materials for the fabrication of heat exchange equipment that will be serviceable under hydrotreating conditions. This paper discusses the Orenburg condensate hydrotreating unit which has been shut down repeatedly for repair because of corrosion damage to components of heat exchangers in the reactor section: tube bundles (08Kh18N10T steel), corrugated compensators (12Kh18N10T steel), and pins of the floating heads (37Kh13N8G8MFB steel). The authors recommend that the tube bundles and the compensators in heat exchangers in the reaction section should be fabricated of 08Kh21N6M2T or 10Kh17N13M2T steel. The pins have been replaced by new pins made of 10Kh17N13 X M2T steel, increasing the service life from 6-12 months to 2 years

The structure of the alphinizing coat on alloy steels

Directory of Open Access Journals (Sweden)

S. Pietrowski

2008-12-01

Full Text Available In this paper results of the structure of the coat alphinizing in AlSi5 silumin on alloy steels: acid-proof 1H18N9T (X6CrNiTi18-10 and high speed SW18 (HS18-0-1 were presented. The temperature of the alphinizing bath was amounts to750±5°C, and immersion time of the element τ = 180s. It was shown, that there is the different “g” coat thickness on testing steels. On the 1H18N9T steel it amounts to g = 52μm, and on the SW18 steel – g = 203μm. Regardless of a grade of testing alloy steels the coat consist of three layers with diversified phasic structure. There is different chemical composition of coat layers on testing steels. The first layer from the base consist of AlFe phase containing alloy addictions of steels: Cr and Ni (1H18N9T and W, V and Cr (SW18. On this layer crystallize the second layer of intermetallic phases. It is the phase containing the main alloy addiction of steels: AlFeCr (1H18N9T and AlFeW (SW18. The last, outside layer consist of silumin containing AlFeNi intermetallic phases on the 1H18N9T steel and AlFeW on the SW18 steel. Regardless of the grade of testing steels there is Si element in all layers of the coat. There are morphological differences in tested layers. The second layer (AlFeW phase inside the coat on the SW18 steel consist of faced crystals growing into in outside silumin layer. On the 1H18N9T steel a boundary between transient and outside layer is more uniform. Free separations of intermetallic phases inside silumin layer on the 1H18N9T steel have lamellar and on the SW18 steel – faced form.

Preliminary tension effect on low-cycle fatigue of 40Kh13 steel in gaseous hydrogen

International Nuclear Information System (INIS)

Romaniv, A.N.

1984-01-01

Comparative bending tests of specimens deformed by tension at 65, 18 and 30% in hydrogen and vacuum were accomplished to reveal the effect of preliminary tension on low-cycle fatigue strength of 40Kh13 martensitic steel. It was found that small amounts of preliminary strains induced a considerable decrease in low-cycle durability in vacuum and hydrogen which was connected with developing defects arising at the early stages of plastic deformation. A rather high degree of preliminary tension promoted steel homogenization, hydrogen embrittlement decrease and service behaviour improvement

Structural inheritance in cast 30KhGNM-type steel

International Nuclear Information System (INIS)

Sadovskij, V.D.; Bershtejn, L.I.; Mel'nikova, A.A.; Polyakova, A.M.; Schastlivtsev, V.M.

1980-01-01

Structural inheritance in the cast 30KhGNM-type steel depending on the heating rate and the temperature of preliminary tempering is investigated. When eating the cast steel with a beinite structure at the rate of 1-150 deg/min, the restoration of austenite grain and the following recrystallization due to the phase cold work, are observed. Slow heating from room temperature or preliminary tempering hinder grain restoration during heating. A non-monotonous effect of tempering temperature on the structural inheritance is established which can be connected with the kinetics of decomposition of residual austenite in steel

Development and industrial mastering hot rolling procedure for low-ductile steels and alloys

International Nuclear Information System (INIS)

Degterenko, V.K.; Sokolov, V.A.

1980-01-01

The technique for the development of the sheet hot rolling procedure for low-ductile steels and alloys (0Kh17N14M2, 12Kh21N5T, 20Kh25N20C2,40Kh13, 36NKhTYu etc.) is proposed, using plastometer which permits to obtain the data on the deformation resistance in the wide range of temperatures (800-1300 deg C), of deformation degrees (0.1-0.3) and deformation rates (0.001-300 c -1 ). With the help of the plastometric data processed on the computer the calculation of the rolling regimes for the sheet with improved surface quality is carried out at the more uniform loading on the mill stands

The Kinetics of Bainitic Transformation of Roll Steel 75Kh3MF

Science.gov (United States)

Kletsova, O. A.; Krylova, S. E.; Priymak, E. Yu.; Gryzunov, V. I.; Kamantsev, S. V.

2018-01-01

The critical points of steel 75Kh3MF and the temperature of the start of martensitic transformation are determined by a dilatometric method. The thermokinetic and isothermal diagrams of decomposition of supercooled austenite are plotted. The microstructure and microhardness of steel specimens cooled at different rates are studied. The kinetics of the occurrence of bainitic transformation in the steel is calculated using the Austin-Ricket equation.

Effect of heat treatment and rotor steels composition on hydrogen solubility

International Nuclear Information System (INIS)

Ivanov, A.I.; Samojlenko, L.V.; Gorovaya, O.N.; Najdovskij, A.G.; Bilik, I.; Kret, Ya.

1988-01-01

Measurements of equilibrium hydrogen adsorption in samples of 27KhN3MFA and 25Kh2NMFA steels were conducted. Carbide inclusions and doping additions, typical for rotor steels, don't produce noticeable effect on hydrogen solubility in

Choice of corrosion-resistant metal for fluotitanic acid

International Nuclear Information System (INIS)

Reingeverts, M.D.; Lapchenko, E.P.; Semenyuk, E.Y.

1986-01-01

The authors investigate the corrosion and anodic behavior of steels 12Kh18N10T, 08Kh21N6M2T, and 06KhN28MDT, nickel, and molybdenum in 10-40% naturally aerated solutions of H 2 TiF 6 at 20 and 50 degrees C. The authors found that in solutions of fluotitanic acid, as also in tetrafluoroboric and hydrofluoric acids, the most stable alloys are chromium-nickel-molybdenum alloy of type 06KhN28MDT and (for acid concentrations above 20%) copper-nickel-alloys of the monel metal type. Steels 12Kh18N10T and 08Kh21N6M2T can be used in acid concentrations of less than 10% and temperatures up to 20 degrees C with anodic protection

Investigation of Creep Processes and Microdamages in 10Kh9V2MFBR-Sh High-Chromium Steel

Science.gov (United States)

Grin', E. A.; Pchelintsev, A. V.

2018-01-01

During the modernization and the new construction of power units at TPPs in Russia, high-chromium martensitic steels with higher heat-resistant properties than the traditional perlite steels are increasingly used as structural materials. High-chromium steels have a necessary regulatory support for their use in domestic power engineering. However, up to the present time, the issue of assessing the quality of these steels at the analysis of their state during long-term operation remains open. The article proposed is one of the first attempts to create a system of quality criteria for martensitic steels based on their microdamage parameters. Tests were carried out on the long-term strength and creep of samples from 10Kh9V2MFBR-Sh steel at high temperatures with the construction of creep curves in relative coordinates "deformation related to the deformation of fracture, current time related to time to failure." For some samples, the tests were interrupted and the metal was subjected to metallographic studies consisting of the analysis of microdamage with reference to the accumulated creep strain. It has been shown experimentally that the deformation curve of high-chromium steel differs from the analogous curve of pearlitic steel by a longer and flat section of steady creep and by a sharper transition to the third accelerated creep stage, which has a very short time period (approximately 10% of the total durability). The tendency to the increase in the microdamage of the structure of steel as the accumulated creep strain increases with time was confirmed. The beginning of transition to the final creep phase is characterized by the formation of contours of future pore chains and by the appearance of individual large pores of up to 6 μm in size, the presence of which in the microstructure of the martensitic steel indicates a very significant accumulation of creep strain, and corresponds to the predestruction stage of metal. It is necessary to continue the research to

Microstructure and Mechanical Properties of Fe-18Mn-18Cr-0.5N Austenitic Nonmagnetic Stainless Steel in Asymmetric Hot Rolling

Science.gov (United States)

Song, Y. L.; Li, C. S.; Ma, B.; Han, Y. H.

2017-05-01

Asymmetric hot rolling (ASHR) with a mismatch speed ratio of 1.15 in a single pass was applied to Fe-18Mn-18Cr-0.5N steel and was compared with symmetric hot rolling (SHR). The results indicated that a through-thickness microstructure gradient was formed in the plate due to the shear strain (0.36) introduced by ASHR. A fine-grained layer with the average size of 3 μm was achieved at the top surface of ASHR plate, while numerous elongated grains with a few recrystallized grains were presented at the center layer. The texture was distributed randomly at the top surface of ASHR plate, and a weaker intensity of typical hot-rolled texture in austenitic steel was obtained at the center layer of ASHR plate compared to SHR plate. An excellent combination of microhardness, strength and ductility was obtained in the ASHR plate, which was attributed to gradient microstructure induced by ASHR.

Effect of operational conditions of electroerosion machining on the surface microgeometry parameters of steels and alloys

International Nuclear Information System (INIS)

Foteev, N.K.

1976-01-01

Studies the influence of pulse duration and a series of operating conditions of a ShGI-40-440 spark-machining generator on changes in the basic surface microgeometry characteristics of components of stainless steel 1Kh18N10T, steel St 45 and hard alloy T14K8. The microgeometry characteristics of spark-machined surfaces differ significantly from the corresponding characteristics of surfaces machined by cutting and vibro-rolling

Stainless austenitic steels strengthened due to reversible phase transformations and by ageing

International Nuclear Information System (INIS)

Sagaradze, V.V.; Kositsyna, I.I.; Ozhiganov, A.V.

1981-01-01

The effect of the reversible phase transformations, consisting in the conduction of the direct and reverse martensite transformations and aging, during which the intermetallide γ'-phase of the composition Ni 3 Ti is formed, on the streng-thening of alloys in the Fe-Cr-Ni-Ti system is considered. Stainless austenitic steels Kh12N12T3 and Kh12N14T3, which acquire high mechanical properties: σsub(0.2)=685-785 MPa, σsub(B)=1275 MPa, delta >= 20%, as a result of reversible phase transformations and aging, are suggested. After the reversible phase transformations and ageing the steels possess a high resistance to γ-α-transformation during cold treatment [ru

The effect of thermoplastic treatment regimes on the microplastic strain of nitrogen-containing steel Kh21G10N7MBF

International Nuclear Information System (INIS)

Bannykh, O.A.; Blinov, V.M.; Kostina, M.V.; Grachev, S.V.; Mal'tseva, L.A.

2005-01-01

A study is made into the influence of a percentage reduction during cold rolling and subsequent holdings at heat on development of microplastic deformation when bending sheet specimens of stainless austenitic high-nitrogen steel Kh21G10N7MBF. It is revealed that a maximum value of apparent limit of elasticity (∼1800 MPa) is attained due to plastic deformation by rolling at 20 Deg C with a total percentage reduction of 60 % and subsequent aging at 500 Deg C for 1-4 h [ru

Non-destructive automated express method for determining the inclination of chromium-nickel steels IGC

International Nuclear Information System (INIS)

Nazarov, A.A.; Kamenev, Yu.B.; Kuusk, L.V.; Kormin, E.G.; Vasil'ev, A.N.; Sumbaeva, T.E.

1986-01-01

Methods of automated control of 18-10-type steel inclination to IGC are developed and a corresponding automated testing complex (ATS) is created. 08Kh18N10T steel samples had two variants of thermal treatment: 1) 1200 deg (5 h), 600 deg (50 h); 2) 1200 deg (5 h). Methods of non-destructive automated control of 18-10-type steel inclination to IGC are developed on the basis of potentiodynamic reactivation (PR) principle. Automated testing complex is developed, which has undergone experimental running and demonstrated a high confidence of results, reliability and easy operation

Study of cast and thermo-mechanically strengthened chromium-nickel nitrogen-containing steel

International Nuclear Information System (INIS)

Prokoshkina, V.G.; Kaputkina, L.M.; Svyazhin, A.G.

2000-01-01

The effect of nitrogen on the structure and strength of corrosion-resistant chromium-nickel steels after thermal and thermomechanical treatment is studied. The 06Kh15N7AD and 07Kh15N7DAMB steels alloying by nitrogen was accomplished through the basic composition steels remelting in the molecular nitrogen atmosphere under the pressure of 0.1-2.5 MPa. The 02Kh15N5DAF and 05Kh15N5DAM steels ingots were obtained through melting in a plasma furnace under the nitrogen pressure of 0.4MPA. The high-temperature thermomechanical treatment (HTMT) was performed by rolling with preliminary blanks heating up to 1050 deg C and the rolling end temperature not below 950 deg C. It is shown, that the HTMT of the nitrogen-containing steels makes it possible to obtain strength characteristics by 1.5 times exceeding the properties of traditionally applicable corrosion-resistant steels, whereby sufficiently high plasticity of the nitrogen-containing steel is retained [ru

Structure and phase composition of titanium nitride coating on austenitic steel

International Nuclear Information System (INIS)

Dubovitskaya, N.V.; Kolenchenko, L.D.; Larikov, L.N.

1989-01-01

Structure and phase composition of titanium nitride coating deposited on 08Kh18N10T steel substrate using ''Bulat'' device are studied. Use of complex investigation methods permitted despite small coating thickness (1μm) to aquire information on hardness, porosity, to study phase composition in all coating thickness. The surface layer (∼0.1 μm) consists of ε-Ti 2 N, TiN 0.6 , TiC 0.35 , that is formed with carbon participation from oil vacuum. In more deeper layers beside ε-Ti 2 N TiC 0.14 N 0.77 is present. Effect of carbon diffusion from substrate to forming coating is stated. Gradient of element concentrations in the substrate-coating interface causes recrystallization of austenite

Hydrogen effect on mechanical properties and flake formation in the 10KhSND steel rolled plates

Energy Technology Data Exchange (ETDEWEB)

Muradova, R G; Zakharov, V A; Kuzin, A P; Gol' tsov, V A; Podgajskij, M S [Donetskij Politekhnicheskij Inst. (Ukrainian SSR); Donetskij Nauchno-Issledovatel' skij Inst. Chernoj Metallurgii (Ukrainian SSR))

1982-01-01

The effect of hydrogen on mechanical properties of the 10KhSND steel rolled plates during natural aging is studied. Optimum period of metal acceptance tests, which are advisable to conduct after 5-7 day natural aging of finished products, are found out. The technique is worked out and a safe hydrogen content to prevent flake formation in the 10KhSND steel is determined. It is shown that a safe hydrogen content is dependent on the experiment conditions (sample dimensions, conditions of cooling, and prehistory).

Hydrogen effect on mechanical properties and flake formation in the 10KhSND steel rolled plates

International Nuclear Information System (INIS)

Muradova, R.G.; Zakharov, V.A.; Kuzin, A.P.; Gol'tsov, V.A.; Podgajskij, M.S.

1982-01-01

The effect of hydrogen on mechanical properties of the 10KhSND steel rolled plates during natural aging is studied. Optimum period of metal acceptance tests, which are advisable to conduct after 5-7 day natural aging of finished products, are found out. The technique is worked out and a safe hydrogen content to prevent flake formation in the 10KhSND steel is determined. It is shown that a safe hydrogen content is dependent on the experiment conditions (sample dimensions, conditions of cooling, and prehistory)

Study of 16KhSN high strength steel in different structural states and under working conditions

International Nuclear Information System (INIS)

Skudnov, V.A.; Vorob'ev, I.A.; Kutyajkin, V.G.; Bugrov, Yu.V.

1985-01-01

A study was made on the effect of deformation degree (up to 60%) during reducing, drawing and heat treatment (annealing at 750 deg C), quenching from 930 deg C and tempering at 350 deg C) on strength, plasticity, hardening degree, notch sensitivity, density and elasticity characteristics of the steel. The effect of test temperature (from-196 up to 1000 deg C) on tensile strength and plasticity was studied as well. It was established that drawing and reducing of 16KhSN steel in annealed state with strain degrees of up to 60% results to increase of strength characteristics 1.7...2.3 times and decrease of plasticity characteristics by 15...23%, strain hardening coefficient - 2.2 times and the maximum strain energy - by 80 MJ/m 3 . Hardening heat treatment (quenching from 930 deg C+temperating at 350 deg C) affects on mechanical properties of 16KhSN steel in much the same way as cold working, but strength characteristics of heat-treated steel increase 2.6...3.6 times and the maximum strain energy grows by 640 MJ/m 3 . Systematic data on the effect of temperature (-196...1000 deg C) and tensile rate (4 mm/min...5m/s) on strength and plasticity of 16KhSN steel in annealed state were obtained

Protective effect of KhOSP-10 inhibitor during corrosion, hydrogenadsorption and corrosion cracking of a steel in sulfuric acid

Energy Technology Data Exchange (ETDEWEB)

Mindyuk, A K; Svist, E I; Savitskaya, O P; Goyan, E B; Gopanenko, A N [AN Ukrainskoj SSR, Lvov. Fiziko-Mekhanicheskij Inst.

1975-01-01

The protective propeties of inhibitor KhOSP-10 in the time of corrosion and corrosive cracking of steel 40Kh are higher then those of inhibitors KPI-1, KI-1, I-I-V etc. Its ability to reduce steel hydrogenation is the same as in the case of KPI-1 inhibitor i.e. below that of KI-1. HCl additives enhance the efficiency of inhibitors KPI-1, KI-1, I-1-V etc. up to the protective ability of KhOSP-10. Kinetics of the electrode processes was estimated from polarization curves.

Cooling rate and microstructure of surface layers of 5KhNM steel, machined by electroerosion method

International Nuclear Information System (INIS)

Foteev, N.K.; Ploshkin, V.V.; Lyakishev, V.A.; Shirokov, S.V.

1982-01-01

The cooling rate and microstructure of surface layers of steel 5KhNM machined by electroerosion method have been studied. It is shown that the difference in heating rate of the surface layers with electric discharge over the 5KhNM steel samples depth results in the intensive size reduction of the microstructure. In the surface layer alongside with martensite residual austenite is present, the lattice period of which increases with the increase of pulse duration, carbide phase of complex composition appears, and concentrational heterogeneity in alloying elements (except carbon) is absent

Cooling rate and microstructure of surface layers of 5KhNM steel, machined by electroerosion method

Energy Technology Data Exchange (ETDEWEB)

Foteev, N.K.; Ploshkin, V.V.; Lyakishev, V.A.; Shirokov, S.V.

1982-01-01

The cooling rate and microstructure of surface layers of steel 5KhNM machined by electroerosion method have been studied. It is shown that the difference in heating rate of the surface layers with electric discharge over the 5KhNM steel samples depth results in the intensive size reduction of the microstructure. In the surface layer alongside with martensite residual austenite is present, the lattice period of which increases with the increase of pulse duration, carbide phase of complex composition appears, and concentrational heterogeneity in alloying elements (except carbon) is absent.

Heating temperature effect on ferritic grain size of rotor steel

International Nuclear Information System (INIS)

Cheremnykh, V.G.; Derevyankin, E.V.; Sakulin, A.A.

1983-01-01

The heating temperature effect on ferritic grain size of two steels 13Kh1M1FA and 25Kh1M1FA is evaluated. It is shown that exposure time increase at heating temperatures below 1000 deg C up to 10h changes but slightly the size of the Cr-Mo-V ferritic grain of rotor steel cooled with 25 deg C/h rate. Heating up to 1000 deg C and above leads to substantial ferritic grain growth. The kinetics of ferritic grain growth is determined by the behaviour of phases controlling the austenitic grain growth, such as carbonitrides VCsub(0.14)Nsub(0.78) in 13Kh1M1FA steel and VCsub(0.18)Nsub(0.72) in 25Kh1M1FA steel. Reduction of carbon and alloying elements content in steel composition observed at the liquation over rotor length leads to a certain decrease of ferritic grain resistance to super heating

Interaction of steel, titanium and zirconium with melted chlorides containing copper and zinc

International Nuclear Information System (INIS)

Ozeryanaya, I.N.; Manukhina, T.I.; Shibanov, B.S.

1976-01-01

Cu and Zn coatings were obtained by contact displacement of their molten chlorides. Cu was deposited on Kh18N10T stainless steel, and Zn was deposited on Ti or Zr at 400-550 0 . Cu was displaced from the electrolyte by all components in the steel. A smooth coating exhibited high adhesion. According to metallography there was a transition layer of a Ni-Cr solid solution between the surface Cu layer and steel. With electronegetiol Ti and Zr, contact deposition of Zn or Cu from chloride melts was possible. The coatings were multilayer and exhibited adequate adhesion. The coating consisted of an intermetallic compound of Ti or Zr with Zn

Specific features of precipitation hardening of austenitic steels with various base. 2. Kinetics and mechanism of carbide precipitation

International Nuclear Information System (INIS)

Kositsyna, I.I.; Sagaradze, V.V.; Khakimova, O.N.

1997-01-01

Electron microscopic studies were carried out to determine the kinetics and mechanisms of precipitation hardening in Fe-Mn, Fe-Mn-Cr, Fe-Cr-Mn-N, Fe-Cr-Ni and Fe-Ni base stainless steels (45G20M2F2, 50Kh16G15N6M2F2, 45Kh18N10G10M2F2, 40Kh18Ni18M2F2, 45N26M2F2). The steels were heat treated under various conditions. It is revealed that in manganese steels the particles of vanadium carbide nucleate according to homogeneous mechanism at all aging temperatures (600-750 deg C). The presence of chromium in the matrix promotes the transition to heterogeneous mechanism of carbide nucleation and growth. With nickel content increasing the plasticity of precipitation hardened steels gets better due to more intense diffusion of atoms and vacancies to grain boundaries and, hence, the widening of near-boundary zones free of carbide particles

Specific features of the occurrence, development, and re-compaction of spall and shear fractures in spherically-convergent shells made of unalloyed iron and some steels under their spherical explosive loading

International Nuclear Information System (INIS)

Kozlov, E.A.; Brichikov, S.A.; Gorbachev, D.M.; Brodova, I.G.; Yablonskikh, T.I.

2007-01-01

Results of comparative metallographic examination of recovered shells exposed to explosive loading in two modes (with and without a heavy casing confining explosion products scatter) are presented. The shells were made of high-purity and technical-grade unalloyed iron with the initial grain size 250 and 125 μm, steel 30KhGSA in delivery state and quenched up to HR C 35...40, austenitic stainless steel 12Kh18N10T. The heavy casing used in experiments is demonstrated to ensure a rather compact convergence of shells destroyed at high radii. In the described comparative experiments, one managed to compile the 12Kh18N10T steel shell, after it was spalled at high radii and exposed to shear fracture and spallation layer fragmentation at medium radii, into a compact sphere but failed to do the same with the 30KhGSA quenched steel shell after it was fractured according to spall and shear mechanisms at high and medium radii. Polar zones of this steel shell have obvious undercompressed areas due to significant dissipative losses to overcome the shear strength. Occurrence, development, and re-compaction of spall and shear fractures in spherically-convergent shells made of materials, which were already carefully investigated in 1D- and 2D-geometry experiments, were systematically studied in order to verify and validate new physical models of dynamic fractures, as well as up-to-date used in 1D-, 2D- and 3D-numerical algorithms [ru

X-ray diffraction study of slags forming during corrosion resistant steel production

International Nuclear Information System (INIS)

Slavov, V.I.; Zadorozhnaya, V.N.; Shurygina, A.V.

1990-01-01

Using X-ray diffraction analysis slags, forming during corrosion-resistant 12Kh18N10T grade steel production by two flowsheets, are studied. Standard two-slag technology of steel production does not provide efficient disintegration of chromospinelides in slags, gives high steel contamination with respect to nonmetallic impurities, coarse structure and, as a consequence, presence of macrodefects on rolled products surface. One-slag steel melting technology with titanium alloying of the steel at vacuum causes fast removal of chromospinelides at the beginning of reduction period, promotes titanium absorption by the steel, refines nonmetallic inclusions, provides more fine structure and steel plasticity, removes surface defects

Coarsening of (Fe, Cr)23C6 carbide phase on the tempering of 14Kh17N2 chromium-nickel steel

International Nuclear Information System (INIS)

Psarev, V.I.

2002-01-01

Paper lists the results of computer analysis of distribution according to sizes (Fe, Cr) 23 C 6 microparticles resulting from 14Kh17N2 steel tempering under 700 Deg C. Data were obtained at the maximum beneficial magnification of a light microscope. The mentioned curves of distribution densities are characterized by more reliable run from most permissible sizes of dispersed particles. Application of general rules of distributions and of previously elaborated procedure to identify experimental histograms with theoretical distributions enables to derive valuable information on dynamics of coarsening of a disperse phase in this case, as well [ru

Austenite strengthening and softening during hot deformation

International Nuclear Information System (INIS)

Tushinskij, L.I.; Vlasov, V.S.; Kazimirova, I.E.; Tokarev, A.O.

1981-01-01

Processes of formation of austenite structure of 20 and 12Kh18N10T steels during hot deformation and postdeformation isothermal holdings have been investigated by the methods of analysis of curves of hot deformation, high-temperature metallography and light microscopy. Deformation has been exercised by extention in vacuum with average 4x10 -2 s -1 rate. Deformation temperatures of steel 20 are 930 and 1000 deg C, of steel 12Kh18N10T - 1100 deg C. It is stated that dynamic recrystallization takes place in both investigated steels during hot deformation. In the carbonic steel it is developed by shifting sections of high-angular boundaries, flow stress in this case remains constant. Recrystallization is developed by subgrain coalescence in austenite steel, that brings about preservation of increased defect density in recrystallized volumes. As a result strengthening of steel is continued up to fracture during the increase of the deformation degree. Postdeformation weakening of 12Kh18N10T steel is slowed down as compared with weakening of carbonic steel [ru

Measurement of high temperature elastic moduli of an 18Cr-9Ni-2.95 Cu-0.58 Nb-0.1C (Wt %) austenitic stainless steel

Science.gov (United States)

Tripathy, Haraprasanna; Hajra, Raj Narayan; Sudha, C.; Raju, S.; Saibaba, Saroja

2018-04-01

The Young's modulus (E) and Shear modulus (G) of an indigenously developed 18Cr-9Ni-0.1C-2.95 Cu-0.58Nb (wt %) austenitic stainless steel has been evaluated in the temperature range 298 K to 1273 K (25 °C to 1000 °C), using Impulse excitation technique (IET). The Bulk modulus (K) and the poison's ratio have been estimated from the measured values of E and G. It is observed that the elastic constants (E, G and K) are found to decrease in a nonlinear fashion with increase in temperature. The Cu precipitation is found to influence the elastic moduli of the steel in the cooling cycle. The observed elastic moduli are fitted to 3rd order polynomial equations in order to describe the temperature dependence of E, G, K moduli in the temperature range 298-1273 K (25 °C to 1000 °C). The room temperature values of E,G and K moduli is found to be 207, 82 and 145 GPa respectively for the present steel.

On the protective effect of KhOSP-10 inhibitor during corrosion, hydrogenadsorption and corrosion cracking of a steel in sulfuric acid

International Nuclear Information System (INIS)

Mindyuk, A.K.; Svist, E.I.; Savitskaya, O.P.; Goyan, E.B.; Gopanenko, A.N.

1975-01-01

The protective propeties of inhibitor KhOSP-10 in the time of corrosion and corrosive cracking of steel 40Kh are higher then those of inhibitors KPI-1, KI-1, I-I-V etc. Its ability to reduce steel hydrogenation is the same as in the case of KPI-1 inhibitor i.e. below that of KI-1. HCl additives enhance the efficiency of inhibitors KPI-1, KI-1, I-1-V etc. up to the protective ability of KhOSP-10. Kinetics of the electrode processes was estimated from polarization curves

X-ray spectrum microanalysis of copper and stainless steel surface layer after electroerosion machining

International Nuclear Information System (INIS)

Abdukarimov, Eh.T.; Saidinov, S.Ya.

1989-01-01

The results of experimental investigations of the surface layer of copper and steel 12Kh18N10T after electroerrosion treatment by a rotating tungsten electrode in natural and distilled water are presented. It is established that the quantity of electrode material transferred to the surface of the steel treated grows with the spark discharge energy increase. Tungsten concentration in the surface layer reaches 5-10% with the average depth of penetration 40-50 μm

Defect accumulation in welded joints of 12Kh1MF steel steam pipelines during creep

International Nuclear Information System (INIS)

Anokhov, A.E.; Alekhova, I.A.

1982-01-01

Technique for investigation of micropore accumulation in 12Kh1MF steel welded joints is proposed. The micropore density in different zones of welded joints in non-uniform. It is shown that failure localization in welded joint in the softening zone during the creep takes place due to the micropore priority accumulation in this zone. It is found out that accumulation of residual deformations in different zones of 12Kh1MF welded joints under creep runs more uniformly as the level of working stresses decreases and test duration increases

On change of vanadium carbide state during 20Kh3MVF steel heat treatment

International Nuclear Information System (INIS)

Gitgarts, M.I.; Maksimenko, V.N.

1975-01-01

The Xray diffraction study of vanadium carbide MC has been made in the steel-20KH3MVF quenched from 970 and 1040 deg and tempered at 660 deg for 210 hrs. It has been found that the constant of the MC crystal lattice regularly varies with the temperature of isothermal hold-up. In the steel tempered after quenching two vanadium carbides of different content could co-exist simultaneously: carbide formed in the quenching process and carbide formed during tempering. The discovered effect of the temperature dependence of the MC content is, evidently, inherent also to other steels containing vanadium

Superheat effect on bainite steel hardenability

International Nuclear Information System (INIS)

Kubachek, V.V.; Sklyuev, P.V.

1978-01-01

The bainite hardenability of 34KhN1M and 35 KhN1M2Ph steels has been investigated by the end-face hardening technique. It is established that, as the temperature of austenitization rises from 900 to 1280 deg C, the temperature of bainite transformation increases and bainite hardenability of the steels falls off. A repeated slow heating to 900 deg C of previously overheated 34KhN1M steel breaks up grain, lowers the temperature of the bainite transformation and raises the hardenability to values obtained with ordinary hardening from 900 deg C. A similar heating of previously overheated 35KhN1M2Ph steel is accompanied by restoration of initial coarse grains and maintenance of both the elevated bainite transformation temperature and to lower hardenability corresponding to hardening from the temperature of previous overheating

Cold-rolled sheets production of stainless martensite-ageing steel smelted by vacuum arc and electroslag techniques

Energy Technology Data Exchange (ETDEWEB)

Rivkin, A A; Grishkov, A I; Suslin, A P; Nesterenko, A A; Lola, V N [Tsentral' nyj Nauchno-Issledovatel' skij Inst. Chernoj Metallurgii, Moscow (USSR)

1975-05-01

In cooperation with a number of metallurgical works the production of a high strength sheet stainless maraging steel EHP678 (000KH11N10M2T) has been tested by rolling cylindrical ingots of vacuum arc smelting at the blooming (the mass of rough ingots was 5.1 to 6.0 t, that of cleaned ingots - 3.8 to 5.1 t) or rectangular ingots of electroslag smelting (13 t) at the slabbing. The recommended regimes of heating and deformation are much similar to those used for the steel-KH18N10T. The output of valid cold-rolled sheets proved to be rather low (0.24 t/t for the vacuum arc smelting and 0.30 t/t for the electroslag smelting) mainly due to the losses on cleaning and a considerable portion of wrong-size slabs. The data are presented on the steel-EHP678 properties after various heat treatments. For the production of wide cold-rolled sheets of the steel EHP678 it is recommended to use steelmaking procedure with electroslag smelting including open-hearth melting in arc furnaces, rolling of ingots at the slabbing with heating up to 1260-1280 deg C (hold-up of 4.5 to 5 hrs); electroslag smelting for rectangular section slabs, rolling of ingots of electroslag smelting at the slabbing with their heating up to 1250 deg C (hold-up of 5.5 to 6 hrs), rolling at the 1680-type mill with heating up to 1250-1260 deg C (hold-up of 4 to 4.5 hrs ensuring the rolling temperature after a rough group not below 1100 deg C), quenching of hot-rolled sheets heating up to 920-940 deg C (hold-up of 3 to 3.5 min/mm), shot peening of sheets for descaling (provided the respective equipment is available) with a subsequent short-time pickling in an acid solution and cold rolling with a summary deformation of 35 to 45 %. The steelmaking with the electroslag smelting is much more profitable as regards to the fine technology of number of the main procedures, convenient cooperation of the works and a considerably greater output of the final products out of one ton of the steel produced.

Fabrication of welded pipes of the KhN45Yu alloy

International Nuclear Information System (INIS)

Lyapunov, A.I.; Krichevskij, E.M.; L'vov, V.N.; Kozlov, N.N.; Kireeva, T.S.

1977-01-01

A highly heat-resistant KhN45Yu (EP 747) alloy has been developed; the alloy is designed to withstand prolonged service in the temperature range of 1000-1300 deg C, or short-term service at 1300-1400 deg C. The satisfactory ductility and good weldability of the alloy have made it possible to obtain sheets and pipes (32 x 2.0 mm) by argon arc welding. The ductility of pipes from EP 747 alloy exceeds that of pipes from KhN78T (EI 435) alloy by 5.10%, the strength being approximately equal. In regard to strength the welded joint differs little from the base metal. The ductility characteristics up to 900 deg C are also equal, since failure occurs in the base metal. At higher temperatures the welded joint fails in the metal of the weld, and its ductility drops sharply. The grain size of the base metal corresponds to No. 3-4. The welded joint has a cast structure with a grain size larger than No. 1, but its ductility characteristics are satisfactory. This structure ensures an increased long-term strength of the material at 1000-1200 deg C

Wear resistance and structural changes in nitrogen-containing high-chromium martensitic steels under conditions of abrasive wear and sliding friction

International Nuclear Information System (INIS)

Makarov, A.V.; Korshunov, L.G.; Schastlivtsev, V.M.; Chernenko, N.L.

1998-01-01

Martensitic nitrogen-containing steels Kh17N2A0.14, Kh13A0.14, Kh14G4A0.22 as well as steel 20Kh13 were studied for their wear resistance under conditions of friction and abrasion. Metallography, X ray diffraction analysis and electron microscopy were used to investigate the structural changes taking place in a thin surface layer on wearing. It is shown that an increase of nitrogen content of 0.14 to 0.22% promotes an enhancement of steel resistance to abrasive and adhesive wear, especially after tempering in the range of 500-550 deg C. Typically, the nitrogen-containing steels exhibit lower resistance to various types of wear in comparison with the steels with high-carbon martensite due to their lower deformability under conditions of friction loading

Rupture of the steel-12KH1MF under creep at temperatures close to 0,5 Tsub(melt)

International Nuclear Information System (INIS)

Berezina, T.G.; Ashikhmina, L.A.; Karasev, V.V.

1976-01-01

Optical and transmission microscopy and fractography techniques have been employed in studying the peculiarities of nucleation and growth of micropores in steel 12Kh1MF at creep. The nucleation of micropores occurs at the initial stages of creep at stress concentration points, predominantly following the retarded shear mechanism. Micropores grow by the way of diffusion, as well as following the deslocation mechanism. An important role in the process of micropore growth is played by pore opening through grain-boundary slip. Pores of 1 to 5 microns in size can be formed along grain boundaries both due to the growth of individual micropores and by coalescence of micropores at points of their concentration. Transition of the creep to the critical phase coincides with the process of the pores blending together to

Piercing by composite electrode tool

International Nuclear Information System (INIS)

Abdukarimov, Eh.T.; Krakov, B.G.; Saidinov, S.Ya.

1990-01-01

The construction of the electrode consisting of a dielectric shell, where a working liquid enters, and a metal rod is designed for precision super-deep piercing by the electroerosion treatment method. Technological parameters of piercing with small diameter (0.5-1.9 mm) for 12Kh18N10T steel, copper and tungsten are presented. A possibility to use a new tool for treating components of any form and sizes is marked

Determination of constant of chemical reaction rate in the process of steel treatment in the endothermal atmosphere

International Nuclear Information System (INIS)

Gyulikhandanov, E.L.; Kislenkov, V.V.

1978-01-01

The high-temperature method was applied to measuring a relative variation in the electrical resistance of a thin steel foil prepared from the 12KhN3A, 18Kh2N4VA, 20KhGNR, and 20Kh3MVF steels during its carburization and decarburization, and determined was the temperature dependence of the reaction rate of the interaction of the endothermal atmosphere of different compositions with the analloyed γ-Fe. A connection has been established between the reaction rate constant and the thermodynamic activity of carbon in the alloyed austenite at the temperature of about 925 deg C, corresponding to the cementation temperature. This provides the quantitative estimation of the above value for any alloyed steels and with the presence of numerical values of diffusion coefficients; this also enables one to carry out an accurate calculation of the distribution of carbon throughout the depth of a layer when effecting the cementation in the endothermal atmosphere

Corrosion-electrochemical behavior of metals in alkali solutions

International Nuclear Information System (INIS)

Levin, V.A.; Levina, E.Eh.

1995-01-01

Results of an investigation into corrosion-electrochemical behaviour of 12Kh18N10T, 10Kh17N13M2T, 08Kh21N6M2T and 15Kh25T steels, 06KhN28MDT and KhN78T alloys as well as NP-2 nickel in sodium, potassium and lithium hydroxide solutions at 95-180 deg C temperatures are considered. It is ascertained, that anode polarization curves of all metals irrespective of hydroxide nature, concentration, temperature, presence of chloride and chlorate additions, are of identic character. The movement of anode polarization curves in the direction of lower current of hydroxide type in NaOH-KOH-LiOH series, temperature and solution concentration reduction at other equal terms. 12 refs.; 6 figs

Hot working effect on austenite transformations in structural steel in continuous cooling

International Nuclear Information System (INIS)

Zajmovskij, V.A.; Kisteh, N.V.; Samedov, O.V.

1979-01-01

Austenite transformations in 40, 40Kh, 40KhN and 40KhNMA steels under hot working at 900 deg C with 20% reduction degree and continuous cooling with 1,7-16 0 /s are investigated. Changing of cooling rate in various ways affects the temperature range of austenite transformation in pearlite and bainite regions. Regulating the cooling rate after hot working one can essentially change the impact strength and steel ductility as a result of high temperature thermomechanical treatment effect

On choice of tempered steels

International Nuclear Information System (INIS)

Govorov, A.A.; Pan'shin, I.F.; Rakhmanov, V.I.

1978-01-01

For the purpose of developing a graphical method for choosing structural steels, a change in the propagation work of a crack and in the critical temperature of brittleness of 40, 40Kh, 40KhN, and 40KhNM steels, was examined depending on the hardness after hardening and tempering. A diagram enabling to choose the grade of steel for making an article of known dimensions according to the preset values of its mechanical properties has been plotted. The developed selection scheme takes into account the hardenability of steels and the influence of the hardness after thermal treatment on the cold-shortness of steel

On effect of some thermodeformation parameters of welding cycle on tendency of pearlitic heat-resisting steels to fracture in reheating

International Nuclear Information System (INIS)

Prokhorov, N.N.; Bardokin, E.V.

1979-01-01

Studied is the inclination of the 12Kh1MF, 15Kh3M1F and N18K9M5T steels subject to thermodeformation cycle imitating a welding one, to fracture in reheating. A hot-rolled metal then subject to the same thermal treatment was used. The imitation of thermodeformation cycle of the welding permitted to vary maximum heating temperatures, the period during which the metal is kept at temperatures higher than 1100 deg C, and the cooling rate of ajacent zone metal. It is shown that the curve of the dependence of deformation ability and the tendency to fracture at the reheating of adjacent zone metal on the rate of its cooling at welding is U-shaped. Deformation ability has its maximum value at the cooling rate of 30 deg c/s in the range 1300 to 1000 deg C

Characteristics of centrifugally cast GX25CrNiSi18-9 steel

Directory of Open Access Journals (Sweden)

R. Zapała

2011-07-01

Full Text Available The paper presents the results of microstructural examinations of the industrial heat-resistant centrifugally cast GX25CrNiSi18-9 steel characterised by increased content of Cu. The study included changes in the microstructure of base cast steel respective of the steel held at a temperature of 900 and 950°C for 48 hours. Based on the results obtained, an increase in microhardness of the examined cast steel matrix with increasing temperature was stated, which was probably caused by fine precipitates enriched in Cr, Mo, and C forming inside the matrix grains.The layer of scale formed on the tested cast steel oxidised in the atmosphere of air at 900 and 950°C was characterised by an increased tendency to degradation with increasing temperature of the conducted tests.

Effect of metal properties of casts of steel-15Kh1M1FL on the crack resistance at 565 deg C

International Nuclear Information System (INIS)

Gladshtejn, V.I.; Sheshenev, M.F.

1976-01-01

Results are given of prolonged tests of the metal of industrial casts with various fluidity limits. It has been shown experimentally that a quite satisfactory crack resistance is characteristic of a metal with a fluidity limit in the range 30-50 kgf/mm 2 . Metallographic studies have been conducted. Upon variation of the structure and properties of the 15Kh1M1FL steel during operation, the rate of growth of small cracks (up to 2.0 mm) decreases almost by 3 orders of ten (from 1.4x10 -4 to 2.0x10 -7 mm/hour). Subsequent structural changes during prolonged operation (over 50000 hours) result in a gradual increase in the rate of crack growth. At the same time resistance towards appearance of the impermissible high rate of the crack growth, Ksub(10sup(-3)), diminishes monotonically with the operation time. The metal of industrial 15Kh1M1FL steel casts has good crack resistance (Ksub(10sup(-3)) =30-70 kgf/mmsup(3/2) and Vsub(ef) =) kgf/mm 2 ) and a satisfactory local plasticity (critical opening being no more than 0.20 mm for 10 3 hours)

Metastable structure formation during high velocity grinding

International Nuclear Information System (INIS)

Samarin, A.N.; Klyuev, M.M.

1984-01-01

Metastable structures in surface layers of samples are; investigated during force high-velocity abrasive grinding. Samples of martensitic (40Kh13), austenitic (12Kh18N10T), ferritic (05Kh23Yu5) steels and some alloys, in particular KhN77TYuR (EhI437B), were grinded for one pass at treatment depth from 0.17 up to 2.6 mm. It is established that processes of homogenizing, recrystallization and coagulation are; developed during force high-velocity grinding along with polymorphic transformations in the zone of thermomechanical effect, that leads to changes of physical and mechanical properties of the surface

Methods for protection of high-strength welded stainless steel from corrosion cracking

International Nuclear Information System (INIS)

Lashchevskij, V.B.; Gurvich, L.Ya.; Batrakov, V.P.; Kozheurova, N.S.; Molotova, V.A.; Shvarts, M.M.

1978-01-01

The efficiency of protection from corrosion cracking under a bending stress of 100 kgf/mm 2 in a salt mist and in a sulphur dioxide atmosphere, of welded joints of steel 08Kh15N5D2T with metallizing, galvanic and varnish coatings and lubricants, and of steel 1Kh15N4AM3 with sealing compounds has been investigated. Metallization of welded joints with aluminium and zinc efficiently increases corrosion resistance in a salt mist. Galvanic coatings of Cd, Zn, and Cr increase the time to cracking in a salt mist from 2-3 to 60-80 days. The protective properties of varnishes under the effect of a salt mist decrease in the following sequence: epoxy-polyamide enamel EP-140, acrylic enamel C-38, silicone enamels KO-834, KO-811, and KO-814. In an atmosphere containing SO 2 0.15 vol.% at 100% relative humidity, the varnishes investigated, with the exception of the inhibited coating XC-596, show lower protective properties than in a salt mist. The high efficiency of protection from corrosion cracking in a salt mist of slots of steel 1Kh15N4AM3 when using organic sealing compounds U4-21 and U5-21, and also slushing lubricants and oils PVK, TsIATIM-201, K17, and AMS3 was established

Long-term Stability of 9- to 12 % Cr Steels

DEFF Research Database (Denmark)

Hald, John

2004-01-01

In the recent 25 years creep rupture strength of 9- to 12 %Cr steels for steam pipes and turbines has been doubled by development of new alloys. This development has formed a basis for improved efficiency of fossil fired steam power plants by introduction of advanced steam temperatures...... and pressures. Newly developed steam pipe steels are based on modifications of well-established steels like the X 20CrMoV12 1. Balanced addition of V, Nb and N to a 9Cr 1 Mo steel led to the Modified 9 Cr steel P 91. Addition of 1% W to a 9Cr 1 MoVNbN base composition led to steel E 911 and partial replacement...... of Mo with 1.8 % W combined with a slight amount of Boron led to steel P 92. The creep rupture strength of these new alloys are now secured with long-term tests up to 100,000 hours, which demonstrate improvements of 50% (P 91), 75 % (E 911) and 100 % (P 92) in strength compared to X 20CrMoV12 1....

Tensile and Charpy impact properties of an ODS ferritic/martensitic steel 9Cr–1.8W–0.5Ti–0.35Y{sub 2}O{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Zhang, Guangming; Zhou, Zhangjian, E-mail: zhouzhj@mater.ustb.edu.cn; Wang, Man; Li, Shaofu; Zou, Lei; Zhang, Liwei

2014-04-15

Highlights: • The tensile property and Charpy impact were tested. • Both strength and plasticity in LT direction are better than that of TL direction. • The LSE was more than 65% of the USE from absorbed energy curve. • The initiation and propagation energy at different temperatures were calculated. • High LSE and dimples on the fracture surface indicated good toughness at −60 °C. - Abstract: A 9Cr-ODS ferritic/martensitic steel with a composition of 9Cr–1.8W–0.5Ti–0.35Y{sub 2}O{sub 3} was fabricated by mechanical alloying and hot isostatic pressing, followed by hot rolling. Tensile properties were measured at room temperature (23 °C) and 700 °C in the rolling direction (LT) and the transverse direction (TL). The ultimate tensile strength (UTS) of the as-rolled samples in both directions reached 990 MPa at 23 °C, and still maintained at 260 MPa at 700 °C. The tensile strength and elongation of the rolling direction was greater than that of the transverse direction. The Charpy impact was tested from −100 to 100 °C in the LT direction. The lower shelf energy (LSE) was more than 65% of the upper shelf energy (USE). The total absorbed energy was separated into the energies for crack initiation and propagation. The propagation energy was always higher than the initiation energy in the range of temperatures tested. The ductile-to-brittle transition temperature (DBTT) of the rolled 9Cr ODS evaluated by an absorbed energy curve was about 0 °C. However, the high LSE and the fracture surface that still contained dimples at lower shelf indicated good toughness of the as-rolled 9Cr ODS steels at temperature of −60 °C.

Influence of anisotropic hardening on longitudinal welding strains and stresses

International Nuclear Information System (INIS)

Gatovskij, K.M.; Revutskij, M.N.

1981-01-01

The algorithm and program for estimation of longitudinal welding strains and stresses with account of hardening and Bauschinger effect, which expand the possibilities of more complete description of stress change during thermodeformation welding cycles at bead surfacing on plate made of the 06Kh18N9T steel and AMg61 alloy. It is shown that for metals, deformation curves which are characterized by considerable yield moduli (Esub(T)/E>=0.05) hardening effect is considerable and its account leads to the decrease of stress level in the heataffected zone (down to 20%) [ru

Optimum conditions for aging of stainless maraging steels

International Nuclear Information System (INIS)

Mironenko, P.A.; Krasnikova, S.I.; Drobot, A.V.

1980-01-01

Aging kinetics of two 0Kh11N10M2T type steels in which 3 % Mo (steel 1), and 3 % Mo and 11 % Co (steel 2) had been additionally introduced instead of titanium were investigated. Electron microscopy and X-ray methods were used. It was ascertained that the process of steel aging proceeded in 3 stages. Steel 2 was hardened more intensively during the aging, had a higher degree of hardness and strength after the aging, weakened more slowly if overaged than steel 1. The intermetallide hcp-phase Fe 2 Mo was the hardening phase on steels extended aging. Optimum combination of impact strength and strength was was achieved using two-stage aging: the first stage - maximum strength aging was achieved, the second stage - aging at minimum temperatures of two-phase α+γ region

Effect of preliminary neutron irradiation on helium blistering of 0Kh16N15M3B steel

International Nuclear Information System (INIS)

Chernov, I.I.; Kalin, B.A.; Skorov, D.M.; Shishkin, G.N.; Ivanov, M.V.

1982-01-01

The method of electron microscopy has been applied to investigate the effect of preliminary neutron irradiation on the OKh16N15M3B steel blistering under irradiation by 20 keV helium ions with (1-10)x10 21 ion/m 2 doses at the temperature below 373 K. It is shown that neutron irradiation shifts critical doses of blister formation and intense scaling towards higher doses. But after the incubation period the erosion of steel preliminary neutron irradiated grows with the increase of helium ion dose above 7x10 21 ion/m 2 . Short-term heating of neutron irradiated samples during 15 min at 1173 K does not practically affect the beginning of intense scaling of the surface

Numerical simulation of Cr2N age-precipitation in high nitrogen stainless steels

International Nuclear Information System (INIS)

Dai, Q.X.; Yuan, Z.Z.; Luo, X.M.; Cheng, X.N.

2004-01-01

At the temperature raging from 700 to 950 deg. C, the Cr 2 N age-precipitation in high nitrogen austenitic stainless steels Fe24Mn18Cr3Ni0.62N was investigated in this paper. A qualitative mathematical model of Cr 2 N age-precipitation, ln t S = f (Me,1/T), was established based on the thermodynamics and kinetics and phase transformation theories. Satisfactory results were obtained by means of the test of artificial neural network. This mathematical model can be applied to the calculation design and predication of Cr 2 N age-precipitation in high nitrogen stainless steels

Effect of Heat Treatment on the Structure and Properties of Die Steel 70Kh3G2FTR

Science.gov (United States)

Krylova, S. E.; Kletsova, O. A.; Gryzunov, V. I.; Fot, A. P.; Tavtilov, I. Sh.

2018-01-01

The effect of heat treatment parameters on the properties and structural and phase composition of a promising die steel 70Kh3G2FTR for hot deformation is studied. The temperature-and-stress state of a hammer die under a heat treatment is simulated.

Corrosion failure of a bolt made of the 25Kh1MF material

International Nuclear Information System (INIS)

Liska, V.; Cechova, D.; Velkoborsky, J.

1989-01-01

M36x4 bolts, of which there are 222 at each nuclear power plant unit, are made of the 25Kh1MF or 38KhN3MFA steel. They are located in an environment with elevated temperature, with damp air and with boric acid. Corrosion of these bolts is due to the rather poor metallurgical quality of the steel. No inadmissible inhomogeneities of the type of lines of inclusions occur in the bolt material produced by cold rolling but defects of the type of laps were found on the threads. It is suggested that if the cold rolling technology were obviated, corrosion failure of the bolts might not occur. (M.D.). 7 figs., 3 refs

Ductility of high chromium stainless steels

International Nuclear Information System (INIS)

Peretyat'ko, V.N.; Kazantsev, A.A.

1997-01-01

Aimed to optimize the hot working conditions for high chromium stainless steels the experiments were carried in the temperature range of 800-1300 deg C using hot torsion tests and cylindrical specimens of ferritic and ferritic-martensitic steels 08Kh13, 12Kh13, 20Kh13, 30Kh13 and 40Kh13. Testing results showed that steel plasticity varies in a wide range depending on carbon content. Steels of lesser carbon concentration (08Kh13 and 12Kh13) exhibit a sharp increase in plasticity with a temperature rise, especially in the interval of 1200-1250 deg C. Steels 20Kh13 and 30Kh13 display insignificant plasticity increasing, whereas plastic properties of steel 40Kh13 increase noticeably in the range of 1000-1300 deg C. It is shown that optimal hot working conditions for specific steel must be selected with account of steel phase composition at high temperatures

Effect of laser absorption on picosecond laser ablation of Cr12MoV mold steel, 9Cr18 stainless steel and H13A cemented carbide

Science.gov (United States)

Wu, Baoye; Liu, Peng; Wang, Xizhao; Zhang, Fei; Deng, Leimin; Duan, Jun; Zeng, Xiaoyan

2018-05-01

Due to excellent properties, Cr12MoV mold steel, 9Cr18 stainless steel and H13A cemented carbide are widely used in industry. In this paper, the effect of absorption of laser light on ablation efficiency and roughness have been studied using a picosecond pulse Nd:YVO4 laser. The experimental results reveal that laser wavelength, original surface roughness and chemical composition play an important role in controlling ablation efficiency and roughness. Firstly, higher ablation efficiency with lower surface roughness is achieved on the ablation of 9Cr18 at 532, comparing with 1064 nm. Secondly, the ablation efficiency increases while the Ra of the ablated region decreases with the decrease of original surface roughness on ablation of Cr12MoV mold steel at 532 nm. Thirdly, the ablation efficiency of H13A cemented carbide is much higher than 9Cr18 stainless steel and Cr12MoV mold steel at 1064 nm. Scanning electron microscopy images reveals the formation of pores on the surface of 9Cr18 stainless steel and Cr12MoV mold steel at 532 nm while no pores are formed at 1064 nm. As to H13A cemented carbide, worm-like structure is formed at 1064 nm. The synergetic effects of the heat accumulation, plasma shielding and ablation threshold on laser ablation efficiency and machining quality were analyzed and discussed systematically in this paper.

Comparison of mechanical behavior of TiN, TiNC, CrN/TiNC, TiN/TiNC films on 9Cr18 steel by PVD

Science.gov (United States)

Feng, Xingguo; Zhang, Yanshuai; Hu, Hanjun; Zheng, Yugang; Zhang, Kaifeng; Zhou, Hui

2017-11-01

TiN, TiNC, CrN/TiNC and TiN/TiNC films were deposited on 9Cr18 steel using magnetron sputtering technique. The morphology, composition, chemical state and crystalline structure of the films were observed and analyzed by X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and scanning electron microscopy (SEM). Hardness and adhesion force were tested by nanoindentation and scratch tester, respectively. The friction and wear behavior of TiN, TiNC, CrN/TiNC and TiN/TiNC films sliding against GCr15 balls were investigated and compared synthetically using ball-on-disk tribometer. It was found that Tisbnd N, Tisbnd C, Tisbnd Nsbnd C and Csbnd C bonds were formed. The TiN/TiNC film was composed of TiN, TiC and TiNC phases. Hardness and adhesion force results indicated that although the TiN film possessed the highest hardness, its adhesion force was lowest among all the films. Tribological test results showed that the friction coefficient of TiN/TiNC was much lower than that of TiN and the wear rate decreases remarkably from 2.3 × 10-15 m3/Nm to 7.1 × 10-16 m3/Nm, which indicated the TiN/TiNC film has better wear resistance.

Effect of austenitization conditions on kinetics of isothermal transformation of austenite of structural steels

International Nuclear Information System (INIS)

Konopleva, E.V.; Bayazitov, V.M.; Abramov, O.V.; Kozlova, A.G.

1987-01-01

Effect of austenization of kinetics of pearlite and bainite transformations for steels with different carbon content differing by alloying character and degree has been investigated. Austenization temperature increase is shown to leads to retardation of ferrite-pearlite transformation in low- and medium-carbon alloyed steels. Step-like holding in the region of austenite stable state (850, 950 deg) after high-temperature heating (1100 deg C) increases the rate of transformation partially recovering its kinetics and decomposition velocity after low-temperature heating in steels alloyed advantageously with carbide-forming elements (08Kh2G2F, 30Kh3) and does not affect kinetics in the 35Kh, 30KhGSN2A, 45N5 steels. Increase of heating temperature and growth of an austenite grain cause considerable acceleration of bainite transformation, increase of the temperaure of bainite transformation beginning and increase of the transformation amplitude in the 08Kh2G2F, 30Kh3 steels and affect weakly kinetics in steels with mixed alloying (30KhGSN2A) or low-alloy one (35Kh). The bainite transformation rate in the 45N5 steelite does not depend on austenization. The effect of additional acceleration of bainite transformation as a result holding after high-temperature heating in those steels, where activation of transformation occurs with increase of heating temperature

Properties of cast Ti-stabilised stainless steel after long-term ageing

International Nuclear Information System (INIS)

Ehrnsten, U.; Karjalainen-Roikonen, P.; Nenonen, P.; Ahlstrand, R.; Hietanen, O.; Timofeev, B.T.; Bloomin, A.A.

2000-01-01

Mechanical properties and microstructure are studied and compared for two kinds of specimens of cast Ti-stabilized stainless steel 08Kh18N10T used for manufacturing of valves and pumps in nuclear power plants. One set of specimens represents the main gate valve material after 106000 h (∼ 12 years) operation at 270 deg C. The comparison is made with reference specimens in as-fabricated state. The results of impact tests, hardness measurements and microscopic examination show that 12 year operation gives rise to the shift of ductile-brittle transition temperature to higher values (from - 68 deg C - 103 deg C). The microstructure of both materials is similar. The microhardness of δ-ferrite in the steel after long-term operation is slightly higher [ru

Design of the WWER-440 pressurizer

International Nuclear Information System (INIS)

Bednarek, L.

1978-01-01

The main specifications are presented of a pressurizer for the WWER-440 reactor as are factors securing operating reliability and the required life of the equipment. Ferritic-pearlite steel 22K is the basic material for the manufacture of the shell, support and couplings. The internal parts and the heads are manufactured from the 08KH18N10T chromium-nickel austenitic steel, the bolts and nuts of manholes from chromium-molybdenum steels 25KH1MF and 25KH2MFA. Quality testing of basic materials and quality control during the process of manufacture are briefly described. (Z.M.)

Influence of isothermal thermomechanical treatment on structure and properties of structural steels

International Nuclear Information System (INIS)

Smirnov, M.A.; Kaletin, A.Yu.; Schastlivthev, V.M.; Kaletina, Yu.V.

1997-01-01

A study is made into the structure and mechanical properties of steel 35KhGSA and 37KhN3A after isothermal hardening resulting in bainitic structure formation as well as after low-temperature thermomechanical treatment (LTTMT) combining the plastic deformation at the temperature of bainitic transformation and subsequent isothermal hardening. It is shown that LTTMT permits and essential enhancement of strength properties in steel 35KhGSA, high plasticity and impact strength being reserved. This is associated with bainitic structure refinement. In steel 37KhN3A the process of carbide formation takes place along with bainitic transformation, and LTTMT results in lesser strengthening. LTTMT is fount to not practically affect the tendency of structural steels to bainitic brittleness. This treatment promotes some shift of brittleness manifestation to lower temperatures

Corrosion of stainless steel in alcohol solutions of the simplest carboxylic acids

International Nuclear Information System (INIS)

Vigdorovich, V.I.; Korneeva, T.V.; Tsygankova, L.E.

1975-01-01

The behaviour of stainless Kh18N10T steel is considered in the methanol and ethanol solutions of formic and acetic acids, respectively. Consideration is given to the effect of the concentration (C) of the acid (0.01-1.00 N), water (0.1-20.0 mass.%) and temperature (room temperature, 40 and 60 deg C). Curves of anodic polarization were plotted. In the course of time in 1.0 and 0.5 N anhydrous methanol solutions of HCOOH at room temperature in the absence of the external anode current one can observe an increase in the electrode potential. Continued reduction of the formic acid concentration results in an improvement on the initial potential (psi) and a practical constancy of psi in time. It is shown that depending on the acid concentration the additions of water are capable of producing both a passivating and an activating effect. It is assumed that the growth in the length of the hydrocarbon radical of carboxylic acid promotes the adsorption displacement of water and alcohols from the metal surface and enhancement of the corrosion rate

Behaviour of glass and thermal protective coatings on stainless steels in the nitrogen tetroxide based coolant

International Nuclear Information System (INIS)

Bakalin, Yu.I.; Dobrunova, V.M.; Doroshkevich, V.N.; Nesterenko, V.B.; Trubnikov, V.P.

1985-01-01

The technology of application of glass and enamel protective coatings on stainless steel has been examined, their testing in the medium of nitrogen tetroxide based coolant with different content of nitric acid has been carried out, the basic characteristics of the coatings after testing have been defined. Chromium-nickel austenitic 12kh18n10t steel, widely used in the nuclear power, have been chosen as a basic object of examination. The coatings have been tested in nitrogen oxide at P=12.0 MPa, temperature 310 deg C and 0.1% HNO 3 , and also in the medium of vat residue of the rectifying tower with nitric acid content up to 25 mass %. Tests of the coatings have demonstrated their sufficiently high stability, especially of those based on enamels A-20 and BK-5. These coatings are characterised by satisfactory performance and can be used for corrosion protection of the materials used in nuclear power

Influence of chemical heterogeneity of solid solutions on brittleness in chromium steels

International Nuclear Information System (INIS)

Madyanov, S.A.; Sedov, V.K.; Apaev, B.A.

1985-01-01

The role of chemical heterogeneity of solid solutions in formation of mechanical properties of Kh09, Kh15, Kh20, Kh19N2G5T chromium steels has been investigated. It is established that besides the known regioA of chemical heterogeneity in the vicinity of 475 deg C exists a high-temperature region (1000-1050 deg C), where maximum heteroge=- neity of chromium distribution in solid solution, is observed. Both types of chemical heterogeneity cause essential hardening of alloys, which becomes apparent in abrupt change of capability to microplastic deformation The mechanism of occurrence of the given temper brittleness consists in carbon diffusion into microvolunes enriched in carbide-forming elements

Damping capacity of unstable steels on chromium-nickel-manganese base

Energy Technology Data Exchange (ETDEWEB)

Kochkin, L.I.; Rudakov, A.A. (Kirovskij Politekhnicheskij Inst. (USSR))

1982-02-01

The paper deals with results of a study on the energy scattering in OKh13N3G8, 20Kh13N3G4 and 30Kh13N3G4 unstable steels. It is shown that the development of microplastic strains most easily occurs in low-carbon steel having a two-phase structure in the initial state. The proceeding of microplastic deformations in carbon unstable steels is limited by the interstitial atom effect on the dislocation movement. It is established that in OKh13N3G8 steel the martensite ..cap alpha --> gamma..- transformation begins under the cyclic stress amplitudes below the yield point of this steel. The steels studied possess a high vibrostrength.

Investigation of intergranular corrosion resistance of Cr16Ni25NMo6 steel

International Nuclear Information System (INIS)

Kamenev, Yu.B.; Nazarov, A.A.; Kuusk, L.V.; Majdeburova, T.F.

1990-01-01

The effect of 08Kh16N25AM6 steel susceptibility to intergranular corrosion on its intergranular cracking resistance in high-temperature water is investigated. In addition, the performed tests point to the susceptibility of sensibilized Kh16N25AM6 steel to intergranular corrosion in media simulating an agressive environment of power generation equipment; the latter requires a strict control over the resistance of weld joints of the above steel to intergranular corrosion. It is shown that Kh16N25AM6 type steel in sensibilized state is susceptible to intercrystalline corrosion cracking in high-temperature water which correlates with its susceptibility to intergranular corrosion established by AM GOST 6032-84 and potentiodynamic reactivation methods

Investigation of 12Kh1MF steel resistance to brittle fractures

International Nuclear Information System (INIS)

Bologov, G.A.; Rushchits, T.Yu.

1977-01-01

The metal of hot-rolled steam pipe made of 12Kh1MF steel, which has been subjected to thermal treatment under laboratory conditions, and metal samples from acting steam pipes after different exploitation periods at 510-565 deg C have been investigated. The dependence of impact viscosity and its constituents on conditions of thermal treatment has been established. The energy consumed by the developing crack has been used as an impact viscosity criterion. Appropriate thermal treatment is capable of rehabilitating the impact viscosity of embrittled metal. Cold plastic deformation increases crack propagation rate in the initial metal and promotes embrittlement during exploitation. Ageing of the working metal reduces its capacity of stopping the developing crack and shifts the temperature threshold of brittleness towards positive temperature

Effect of boron control of environment on corrosion and resistance to low-cycle corrosion fatigue in structural steels

International Nuclear Information System (INIS)

Babej, Yu.I.; Zhitkov, V.V.; Zvezdin, Yu.I.; Liskevich, I.Yu.; Nazarov, A.A.

1982-01-01

Tests of the specimens on total, contact and crevice corrosion, corrosion cracking and low-cycle fatigue are conducted for determination of corrosion and corrosion-fatigue characteristics in the 15Kh3NMFA, 10N3MFA, 10Kh16N4B, 05Kh13N6M2 structural steels, used in energetics. The environment is subjected to boron control and contacting with atmosphere for simulation of stop and operation modes of the facility. The experiments are carried out in the distilled water with 12g/l H 3 BO 3 and 10 mg/l Cl' at 25, 60, 100 deg C under contacting with atmosphere. It is established, that the pearlitic steels 15Kh3NMFA, 10N3MFA, as well as transition and martensitic 05Kh13N6M2 and 10Kh16N4B steels are highly stable to total, crevice and contact corrosion at the high parameters of aqueous boron-containing medium. Steel resistance to low-cycle fracture decreases slightly under the conditions similar to the operation ones, in the water with 12 g/l H 3 BO 3 . Durability of the pearlitic steels at the simulation of stop conditions decreases more noticeably, crack formation as a rule, initiating from corrosion spots

Structural and phase studies of stainless wire after electroplastic drawing

International Nuclear Information System (INIS)

Troitskij, O.A.; Baldokhin, Yu.V.; Kir'yanchev, N.E.; Ryzhkov, V.G.; Kalugin, V.D.; Sokolov, N.V.; Klekovkin, A.A.; Klevtsur, S.A.

1983-01-01

Structural and phase properties of the 12Kh18N10T steel wire are studied after usual and electroplastic drawing from 0.40 up to 0.11 mm with 18-22% reduction per pass with passing 250 A/mm 2 electric current. The earlier made observation on a sharp decrease in content of deformation-induced martensite of α-phase takes place in the wire from stainless metastable austenitic steel as a result of electroplastic drawing. Distribution of the remained α-phase by the wire cross section is established

Bubble formation upon crystallization of high nitrogen iron base alloys

International Nuclear Information System (INIS)

Svyazhin, A.G.; Sivka, E.; Skuza, Z.

2000-01-01

A study is made into the conditions of nitrogen bubble formation during crystallization of unalloyed iron, alloys of Fe-O, Fe-O-S systems, steels 1Kh13, 0Kh18N9 and a two-phase Fe-11%Cr-1%Mo-0.2%V steel. It is revealed that the amount of bubbles in a high nitrogen steel casting increases with a degree of nitrogen supersaturation and decreases with a cooling rate growth and with a rise of surfactant concentration in the metal. In sound castings a nitrogen content can be increased due to a cooling rate growth, nitrogen dilution with inert gas, an increase of nitrogen pressure during crystallization as well as due to the introduction of such surfactants as sulphur, selenium, tellurium, tin [ru

Damping capacity of unstable steels on chromium-nickel-manganese base

International Nuclear Information System (INIS)

Kochkin, L.I.; Rudakov, A.A.

1982-01-01

The paper deals with results of a study on the energy scattering in OKh13N3G8, 20Kh13N3G4 and 30Kh13N3G4 unstable steels. It is shown that the development of microplastic strains most easily occurs in low-carbon steel having a two-phase structure in the initial state. The proceeding of microplastic deformations in carbon unstable steels is limited by the interstitial atom effect on the dislocation movement. It is established that in OKh13N3G8 steel the martensite α→γ- transformation begins under the cyclic stress amplitudes below the yield point of this steel. The steels studied possess a high vibrostrength [ru

Cyclic crack resistance of anticorrosion cladding-15Kh2MFA steel joint

International Nuclear Information System (INIS)

Zvezdin, Yu.I.; Nikiforchin, G.N.; Timofeev, B.T.; Zima, Yu.V.; Andrusiv, B.N.

1985-01-01

Cyclie crack resistance of transition zone in austenitic cladding steel 15Kh2MFA joint is studied, taking into account the geometry of fatigue cracks, fracture micromechanism and crack closure effect. Kinetics of crack development from the cladding to the basic metal and vice versa is considered. Microstructure of transition zone is investigated. The results obtained are considered as applied to WWER. It is emphasized, that the braking of fatigue cracks is observed at low asymmetry of loading cycle. Increased loading asymmetry accelerates sharply the alloy fracture due to the growth of subcladding crack, at that, the direction of crack propagation and the structure of transition zone are not of great importance

Influence of heating temperature on bainite transformation proceeding in chromium-nickel-molybdenum steels

International Nuclear Information System (INIS)

Kaletin, Yu.M.; Kaletin, A.Yu.

1983-01-01

The purpose of the present paper is to investigate the effect of heating and cooling from austenization temperature on development of bainite transformation in 37KhN3MFA and 18Kh2N4MA structural alloyed steels. The metallographical analysis of specimens has revealed that first crystals of bainite under slow heating up to 770-790 deg C appear at the temperature of about 500 deg C and at 475 deg C there has been much bainite over the whole cross section of the specimen. It is revealed that an increase of heating temperature and cooling rate replace the starting point of bainite transformation upwards. The strongest displacement of the point Bsub(S) into hogh-temperature range takes place after heating steel with the initial bainite structure in intercritical temperature range

Mechanical properties of permeable materials with an organized structure on the base of continuous metal fibers

International Nuclear Information System (INIS)

Karpinos, D.M.; Rutkovskij, A.E.; Zorin, V.A.; Ivanchuk, A.A.

1979-01-01

The mechanical properties were studied for permeable fibrous materials with an organized structure on the base of continuous metal fibers (from Kh18N9T steel) subjected to preliminary reprocessing volumetric net half-finished products. The effect of geometrical parameters of the net half-finished products and of their orientation in packing are shown to affect the mechanical properties within a wide range of porosities

Closed expressions for $\\int_{0}^{1} t^{-1} log^{n-1}t log^{p}(1 - t) dt$

CERN Document Server

Kölbig, Kurt Siegfried

1982-01-01

Closed expressions for the integral integral /sub 0//sup 1/ t/sup -1/ log/sup n-1/t log/sup p/(1-t)dt, whose general form is given elsewhere, are listed for n=1(1)9, p=1(1)9. A formula is derived which allows an easy evaluation of these expressions by formula manipulation on a computer. The majority of the above expressions are given in a microfiche supplement to the paper.

Nitrogen effect on the tendency of Cr-Ni-MN steels to delayed fracture under stress and hydrogen effects

International Nuclear Information System (INIS)

Suvorova, S.O.; Fillipov, G.A.

1996-01-01

Austenitic steels types 03Kh17N16G10AM5, 03Kh6N12G10AM5 and 07Kh13AG20 with various nitrogen contents were studied for their tendency to delayed fracture using mechanical tests, fractography and X ray diffraction analysis. The steel type 07Kh13G20 exhibited the highest strength in the initial state but showed an increase tendency to delayed fracture after hydrogenation. It is underlined that nitrogen additions essentially intensify the tendency of cold worked steels to delayed fracture. This fact should be taken into account when using nitrogen-containing Cr-Ni-Mn steels under severe operational conditions. 4 refs., 2 tabs

Effect of 4-(N,N-diethylamino)benzaldehyde thiosemicarbazone on the corrosion of aged 18 Ni 250 grade maraging steel in phosphoric acid solution

International Nuclear Information System (INIS)

Poornima, T.; Nayak, Jagannath; Nityananda Shetty, A.

2011-01-01

Highlights: → DEABT as corrosion inhibitor for maraging steel in phosphoric acid. → Inhibition efficiency increases with increase in inhibitor concentration. → Inhibition efficiency decreases with increase in temperature. → Adsorption obeys Langmuir adsorption isotherm. - Abstract: 4-(N,N-diethylamino)benzaldehyde thiosemicarbazone (DEABT) was studied for its corrosion inhibition property on the corrosion of aged 18 Ni 250 grade maraging steel in 0.67 M phosphoric acid at 30-50 deg. C by potentiodynamic polarization, EIS and weight loss techniques. Inhibition efficiency of DEABT was found to increase with the increase in DEABT concentration and decrease with the increase in temperature. The activation energy E a and other thermodynamic parameters (ΔG ads 0 , ΔH ads 0 , ΔS ads 0 ) have been evaluated and discussed. The adsorption of DEABT on aged maraging steel surface obeys the Langmuir adsorption isotherm model and the inhibitor showed mixed type inhibition behavior.

Susceptibility to stress corrosion in stainless steels type AISI 321 and 12X18H10T used in PWR type reactors (WWER)

International Nuclear Information System (INIS)

Matadamas C, N.

1995-01-01

Titanium stabilized stainless steels have been utilized in sovietic pressurized water reactors (VVER) for avoid the susceptibility to Intergranular Corrosion (IGC) present in other austenitic stainless steels. However the Intergranular Corrosion resistance of this kind of materials has been questioned because of Intergranular Stress Corrosion Cracking failures (IGSCC) have been reported. This paper study the electrochemical behavior of the AISI 321 stainless steel in a H 3 BO 3 Solution contaminated with chlorides and its susceptibility to Intergranular Corrosion.Electrochemical prediction diagrams of the stainless steels AISI 321 and 12X18H10T (sovietic) sensitized (600 Centigrade, 3 h.) were compared. Cylindrical and conical samples were used in Slow Strain Rate Tests (SSRT), to determine the susceptibility to Stress Corrosion Cracking (SCC) in AISI 321 and 12X18H10T stainless steels. The results obtained showed that the temperature of the solution is a very important factor to detect this susceptibility. Fractography studies on the fracture surfaces of the samples obtained in the SSRT at high temperature were realized. Corrosion velocities of both AISI 321 and 12X18H10T stainless steels were determined using conical samples in the CERT system at high temperature. E.D.A.X. analysis was employed in both AISI 321 and 12X18H10T stainless steels in order to explain the degree of sensitization. (Author)

Fracture of ledeburitic steel during hot plastic deformation

International Nuclear Information System (INIS)

Nikitin, V.P.; Borisov, Yu.A.; Bulat, S.I.; Zajtsev, V.V.

1977-01-01

The mechanisms of the high-temperature failure of high-carbon chromium Kh6F1, Kh6T2 and Kh6VF steels and a possibility to avoid their overheating have been investigated. At 1190 deg C and over the failure occurs along boundaries of grains at points of formation of the initial portions of the liquid phase as carbides are dissolved. If after a holding at 1190-1210 deg C the steels are cooled to 1120-1150 deg C and held for a sufficiently long time, secondary carbides are formed in the eutectic areas and, if the steels are deformed, the discontinuities present a rounded shape. Holding of an overheated steel at 1120-1150 deg C ensures its satisfactory workability in rolling. By choosing adequate overheating and subsequent slight cooling conditions, it is possible not only to retain, but even to improve the plasticity of carbide high-carbon steels. The results of laboratory tests have been confirmed under industrial conditions

Synthesis, Magnetization, and Electrical Transport Properties of Mn3Zn0.9Cu0.1N

Directory of Open Access Journals (Sweden)

Y. Yin

2013-01-01

Full Text Available We synthesized Mn3Zn0.9Cu0.1N by solid state reaction, and magnetic as well as electrical transport properties were investigated. It is found that Mn3Zn0.9Cu0.1N exhibits a first-order antiferromagnetism (AFM to paramagnetic (PM transition with the Néel temperature TN ~163 K, and substitution of Cu for Zn would favor ferromagnetism (FM state and weaken AFM ground state, leading to a convex curvature character of M(T curve. With high external fields 10 kOe–50 kOe, magnetic transition remains a robust AFM-PM feature while FM phase is completely suppressed. Thermal hysteresis of M(T under 500 Oe is also suppressed when the magnetic field exceeds 10 kOe. Mn3Zn0.9Cu0.1N exhibits a good metallic behavior except for a slope change around TN, which is closely related to AFM-PM magnetic transition. Compared with the first differential of resistivity with respect to temperature for (dρ/dTMn3ZnN in transition temperature range, the absolute value of (dρ/dTMn3Zn0.9Cu0.1N is much lower which is close to zero.

Tribological properties and surface structures of ion implanted 9Cr18Mo stainless steels

Science.gov (United States)

Fengbin, Liu; Guohao, Fu; Yan, Cui; Qiguo, Sun; Min, Qu; Yi, Sun

2013-07-01

The polished quenched-and-tempered 9Cr18Mo steels were implanted with N ions and Ti ions respectively at a fluence of 2 × 1017 ions/cm2. The mechanical properties of the samples were investigated by using nanoindenter and tribometer. The results showed that the ion implantations would improve the nanohardness and tribological property, especially N ion implantation. The surface analysis of the implanted samples was carried out by using XRD, XPS and AES. It indicated that the surface exhibits graded layers after ion implantation. For N ion implantation, the surface about 20 nm thickness is mainly composed of supersaturated interstitial N solid solution, oxynitrides, CrxCy phase and metal nitrides. In the subsurface region, the metal nitrides dominate and the other phases disappear. For Ti ion implantation, the surface of about 20 nm thickness is mainly composed of titanium oxides and carbon amorphous phase, the interstitial solid solution of Ti in Fe is abundant in the subsurface region. The surface components and structures have significant contributions to the improved mechanical properties.

Tribological properties and surface structures of ion implanted 9Cr18Mo stainless steels

International Nuclear Information System (INIS)

Fengbin, Liu; Guohao, Fu; Yan, Cui; Qiguo, Sun; Min, Qu; Yi, Sun

2013-01-01

The polished quenched-and-tempered 9Cr18Mo steels were implanted with N ions and Ti ions respectively at a fluence of 2 × 10 17 ions/cm 2 . The mechanical properties of the samples were investigated by using nanoindenter and tribometer. The results showed that the ion implantations would improve the nanohardness and tribological property, especially N ion implantation. The surface analysis of the implanted samples was carried out by using XRD, XPS and AES. It indicated that the surface exhibits graded layers after ion implantation. For N ion implantation, the surface about 20 nm thickness is mainly composed of supersaturated interstitial N solid solution, oxynitrides, Cr x C y phase and metal nitrides. In the subsurface region, the metal nitrides dominate and the other phases disappear. For Ti ion implantation, the surface of about 20 nm thickness is mainly composed of titanium oxides and carbon amorphous phase, the interstitial solid solution of Ti in Fe is abundant in the subsurface region. The surface components and structures have significant contributions to the improved mechanical properties

Irradiation hardening of Mod.9Cr-1Mo steel

International Nuclear Information System (INIS)

Ryu, Woo-Seog; Kim, Sung-Ho; Choo, Kee-Nam; Kim, Do-Sik

2009-01-01

An irradiation test of Mod.9Cr-1Mo steel was carried out in the OR5 test hole of HANARO of a 30 MW thermal power at 390±10degC up to a fast neutron fluence of 4.4x10 19 (n/cm 2 ) (E > 1.0 MeV). The dpa of the irradiated specimens was evaluated to be 0.034 - 0.07. Tensile and impact tests of the irradiated Mod.9Cr-1Mo were done in the hot cell of the IMEF. The change of the tensile strength by irradiation was similar to the change of the yield strength. The increase of the yield and tensile strengths was up to 18% and 10% respectively. The elongation reduction of the weldment was up to 65%. (author)

The effect of alloying and treatment on martensite transformation during deformation in Fe-Cr-Mn steels with unstable austenite

International Nuclear Information System (INIS)

Malinov, L.S.; Konop, V.I.; Sokolov, K.N.

1977-01-01

The effect is studied of alloying with chromium (6-10%), silicon (1-2%), molybdenum (1-3%), and copper (2%), the heat treatment conditions, and the deformation conditions, or the martensitic transformation and mechanical properties of Fe-Cr-Mn steels of the transitional class based on 0G8AM2S. It is shown that appropriate alloying and treatment, taking into account the degree of stability of the austenite, can ensure a complex of high mechanical properties of the steels investigated. For instance, the treatment of steel 0Kh10AG8MD2S by the technique: hardening+ 40% deformation at 400 deg C + 10% deformation at room temperature has yielded the following mechanical properties: sigmasub(B)=150 kgf/mm 2 , sigmasub(T)=110 kgf/mm 2 , sigma=18%, psi=32%

Creep rupture behavior of 9Cr–1.8W–0.5Mo–VNb (ASME grade 92) ferritic steel weld joint

Energy Technology Data Exchange (ETDEWEB)

Sakthivel, T., E-mail: tsakthivel@igcar.gov.in; Vasudevan, M.; Laha, K., E-mail: laha@igcar.gov.in; Parameswaran, P.; Chandravathi, K.S.; Panneer Selvi, S.; Maduraimuthu, V.; Mathew, M.D.

2014-01-03

Creep rupture behavior of 9Cr–1.8W–0.5Mo–VNb (ASME grade 92) ferritic steel weld joint fabricated by activated TIG (A-TIG) welding process have been investigated at 923 K over a stress range of 80–150 MPa. The weld joint was comprise of fusion zone, heat affected zone (HAZ) and base metal. The HAZ consisted of coarse prior-austenite grain (CGHAZ), fine prior-austenite grain (FGHAZ) and intercritical (ICHAZ) regions in an order away from the fusion zone to base metal. A hardness trough was observed at the outer edge of HAZ of the weld joint. TEM investigation revealed the presence of coarse M{sub 23}C{sub 6} precipitates and recovery of martensite lath structure into subgrain in the ICHAZ of the weld joint, leading to the hardness trough. The weld joint exhibited lower creep rupture lives than the base metal at relatively lower stresses. Creep rupture failure location of the weld joint was found to shift with applied stress. At high stresses fracture occurred in the base metal, whereas failure location shifted to FGHAZ at lower stresses with significant decrease in rupture ductility. SEM investigation of the creep ruptured specimens revealed precipitation of Laves phase across the joint, more extensively in the FGHAZ. On creep exposure, the hardness trough was found to shift from the ICHAZ to FGHAZ. Extensive creep cavitation was observed in the FGHAZ and was accompanied with the Laves phase, leading to the premature type IV failure of the steel weld joint at the FGHAZ.

Fatigue resistance of Cr-Ni-Mo-V steel

International Nuclear Information System (INIS)

Naumchenkov, N.E.; Filimonova, O.V.; Borisov, I.A.

1985-01-01

A study was made on the effect of additional alloying (Ni, Ni+Co), stress concentration, surface plastic strain on fatigue resistance of rotor steel of Cr-Ni-Mo-V-composition. It is shown that the steel with decreased carbon content possesses high complex of mechanical properties. Fatigue characteristics are not inferior to similar characteristics of steels of 25KhN3MFA type. Additional alloying of the steel containing 0.11...0.17% C and 4.5...4.7% N:, with niobium separately or niobium and cobalt in combination enabled to improve fatigue resistance of samles up to 25%. Strengthening of stress concentration zones by surface plastic strain is recommended for improving rotor suppporting 'nower under cyclic loading

Boron effect on fabrication properties and service behaviour of complex corrosion-resistant steels

International Nuclear Information System (INIS)

Gol'dshtejn, Ya.E.; Piskunova, A.I.; Shmatko, M.N.

1978-01-01

In order to determine the optimum boron admixtures for the improvement of the technological plasticity without the considerable reduction in the corrosion resistance of the complex alloy Cr-Ni-Mo steels, industrial heats of the 03KH16N15M3, 03KH17N14M3 and other steels, containing 0.0005-0.003% boron, have been researched. The plasticity, corrosion resistance and microstructure of certain steels have been determined. It is shown that small additions of boron enhance the technological plasticity during the ingot rolling. In order to prevent a sharp reduction in the corrosion resistance, the boron content should be confined to 0.0015% and the quenching temperature raised to 1,120-1,150 deg C. The positive effect of the quenching temperature increase is accounted for by the solution of the excess phases and by the reduction of the dislocation density in the near-the-boundary zones

The effect of chromium diffusion redistribution on wear resistance of carburized 3Kh13 steel

International Nuclear Information System (INIS)

Shcherbedinskij, G.V.; Shumakov, A.I.; Zemskij, S.V.; Pereverzev, V.M.

1977-01-01

The redistribution of chromium in steel 3Kh13 on carburization in a high-activity carburizer and the wear-resistance of the steel have been investigated. Surface layers with an increased chromium concentration show the highest wear-resistance. The chromium content in the surface layer increases due to its diffusion from the interior. The distribution of carbon and chromium in the carburized layers has been studied with the aid of the radioactive isotope 14 C by the method of layer-by-layer spectral analysis on a vacuum quantometer, layer-by-layer chemical and X-ray structure analysis. The composition of the carbides has been determined by physicochemical analysis. It has been established that the carburized layer can be divided into four zones with respect to its phase composition: first zone - hematite and spinal with 0.5-2.0% C; second zone - solid carbides (Fe,Cr) 7 C 3 ; up to 5% C; third zone - globular carbides in a troostite matrix (Cr,Fe) 7 C 3 and Cr 23 C 6 ; up to 3.5% C; fourth, transitional, zone - troostite carbide mixture Cr 23 C 6 ; up to 1% C. The chromium diffusion in the carburized layer is faster than in the initial austenite. The chromium counterdiffusion is due to the development of a zone of solid carbides M 7 C 3

Strength of low-carbon rotor steel

International Nuclear Information System (INIS)

Voropaev, V.I.; Filimonov, O.V.; Borisov, I.A.

1988-01-01

The results of studying the effect of chemical composition and thermal treatment regimes on the structural strength of steels of the 25KhN3MFA type are presented. It is shown that alloying with niobium from 0.01 to 0.08% steels with the increased nickel content (4.2-4.5%) contributes to the increase of structural strength and reduction of semibrittleness temperature. To obtain high values of strength and plastic properties cooling with the rate of 10 3 -10 5 K/hr is recommended

Further application of the cleavage fracture stress model for estimating the T{sub 0} of highly embrittled ferritic steels

Energy Technology Data Exchange (ETDEWEB)

Sreenivasan, P.R.

2016-02-15

The semi-empirical cleavage fracture stress model (CFS), based on the microscopic cleavage fracture stress, s{sub f}, for estimating the ASTM E1921 reference temperature (T{sub 0}) of ferritic steels from instrumented impact testing of unprecracked Charpy V-notch specimens is further confirmed by test results for additional steels, including steels highly embrittled by thermal aging or irradiation. In addition to the ferrite-pearlite, bainitic or tempered martensitic steels (which was examined earlier), acicular or polygonal ferrite, precipitation-strengthened or additional simulated heat affected zone steels are also evaluated. The upper limit for the applicability of the present CFS model seems to be T{sub 41J} ∝160 to 170 C or T{sub 0} or T{sub Qcfs} (T{sub 0} estimate from the present CFS model) ∝100 to 120 C. This is not a clear-cut boundary, but indicative of an area of caution where generation and evaluation of further data are required. However, the present work demonstrates the applicability of the present CFS model even to substantially embrittled steels. The earlier doubts expressed about T{sub Qcfs} becoming unduly non-conservative for highly embrittled steels has not been fully substantiated and partly arises from the necessity of modifications in the T{sub 0} evaluation itself at high degrees of embrittlement suggested in the literature.

MR spectroscopy in diagnosis of local recurrence of T3N0M0 of prostate cancer after cryotherapy

International Nuclear Information System (INIS)

Liu Ming; Guo Zhi; Si Tongguo; Wang Haitao; Xiao Bohan

2012-01-01

Objective: To evaluate the usefulness of magnetic resonance spectroscopic imaging in detecting local recurrence in patients with T 3 N 0 M 0 prostate cancer after cryotherapy. Methods: Sixty-five patients with T 3 N 0 M 0 prostate cancer underwent cryotherapy. The preoperative data of conventional MRI, MRS, transrectal ultrasound (TRUS)-guided prostate biopsy were collected. After cryotherapy, the prostate specific antigen (PSA) of all patients was detected monthly.If PSA >5 μg/L, MRI, MRS, and TRUS-guided prostate biopsy were planned within a week. If PSA was unremarkable, MRI, MRS, and TRUS-guided prostate biopsy were planned 12 months after cryotherapy. The prostate was divided 6 regions and the cancerous and noncancerous were marked. The signal-to-noise ratio (S/N) of choline (Cho), citrate (Cit) and the ratios of Cho + creatine (Cre)/Cit of each regions were measured in pre-operation and postoperation. The patients were divided into non-recurrence and recurrence group according to TRUS-guided biopsy. The S/N of Cho, Cit, and the ratio of Cho + Cre/Cit were compared between the groups before and after cryotherapy by using independent samples t-test. Results: (1) Fifteen patients were confirmed local recurrence 12 months after cryotherapy, including 11 patients with an evaluate PSA level and 4 patients with PSA unremarkable. (2) The S/N of Cho, Cit and the ratios of Cho + Cre/Cit in the cancerous and noncancerous regions before cryotherapy in the sixty-five patients were 25±9, 11±5, and 18±5, and 39 ±12, 2.33±0.60, and 0.53 ± 0.19. There had significant difference between that of two groups (t values were 11.36, 9.81, and 13.39, respectively, P=0.00). (3) In the patients with non-recurrence, The S/N of Cho, Cit in the cancerous and noncancerous regions were 4 ± 2 and 3 ± 2 (t=1.024, P=0.305), and 2±2 and 4 ±3 (t=1.147, P=0.178) and no difference was found. In necrotic area,the ratios of Cho + Cre/Cit could not be calculated because of low level of the

Pipes out of the chromium-molybdenum 12Kh2M1 steel intended for power units

International Nuclear Information System (INIS)

Saf'yanov, A.V.; Plyatskovskij, O.A.; Khokhlov-Nekrasov, O.G.; Palatnikova, E.S.; Karpenko, N.P.

1977-01-01

Vanadiumless steel 12Kh2M1 (2.25%Cr, 1%Mo) known to be applied abroad has been used for production of 325x60 mm tubes. The technology involves heating of the blanks to 1270-1300 deg C, their piercing in a double-roller mill, rolling on a pilger mill 8-16'' in thick wall caliber rolls, thermal treatment (normalizing at 930-960 deg C for 1 hour and tempering at 730+-10 deg C for 4 hours and etching (12-22% H 2 SO 4 and up to 143 g/l FeSO 4 ) for 3-4 hours at 55-65 deg C. Good technological properties of the steel and its capacity of working at 540-580 deg C are confirmed. Vanadium alloying of boiler steels does not provide for essential improvement of oxydation resistance and long term strength, but decreases the workability and enhances scatter of working parameters on account of minor variations of chemical composition

Chemical heat treatment of low alloyed maraging steels

Energy Technology Data Exchange (ETDEWEB)

Malinov, L S; Korotich, I K [Zhdanovskij Metallurgicheskij Inst. (Ukrainian SSR)

1979-09-01

The investigation concerned the nitriding, cementation, chromizing, borating of economically alloyed maraging grade 04Kh2N5MFYu steel. The investigated methods of chemothermal treatment were found to considerably increase the hardness of the surface layer of the maraging steel. The high tempering of the grade 04Kh2N5MFYu cemented and hardened steel was found to produce secondary hardening. On chromizing, the diffusion layer is an alloyed ferrite which strengthens because of the dispersion hardening on ageing. The formation of the plastic low-carbon martensite at relatively small cooling rates greatly decreases the tendency of the boride layer to cracking.

Account of internal friction when estimating recoverable creep strain

International Nuclear Information System (INIS)

Demidov, A.S.

1986-01-01

It is supposed that a difference of empirical and calculated data on the creep strain recovery for Kh18N10T steel under conditions of cyclic variations in stress is specified by the effect of internal friction. In the accepted model of creep β-flow is considered to be reversible and γ-flow- irreversible. Absorptivity is determined as a ratio of the difference between the expended work and work of strain recovery forces to the work expended in cycle. A notion of the equivalent stress acting in the period of the creep strain recovery is introduced. Results of the calculation according to the empirical formula where absorptivity was introduced into are compared with empirical data obtained for Kh18N10T steel at 750 deg C

Experimental study on kinematic hardening of 1Cr18Ni9Ti stainless steel under low cycle fatigue

International Nuclear Information System (INIS)

Shao Er; Yang Xianjie; Mao Jianghui; Sun Yafang

2006-01-01

To study the effect of the monotonic loading on subsequent cyclic plastic hardening and flow properties of 1Cr18Ni9Ti steel, an experimental study of the low cycle fatigue tests with mean strains for 1Cr18Ni9Ti stainless steel was carried out. An analysis on the evolutions of the yield surface radius and the back stresses under symmetric and asymmetric cyclic strain loading with different strain amplitudes was made. The dependence of the evolutions of the material kinematic hardening and isotropic hardening on the strain amplitude and mean strain was observed. These results provide the experimental foundation for the constitutive model of the material under combined monotonic and cyclic complicated loads. (authors)

Electrochemical machining of internal built-up surfaces of large-sized vessels for nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Ryabchenko, N N; Pulin, V Ya [Vsesoyuznyj Proektno-Tekhnologicheskij Inst. Atomnogo Mashinostroeniya i Kotlostroeniya, Rostov-na-Donu (USSR)

1977-01-01

Electrochemical machining (ECM) has been employed for finishing of mechanically processed inner surfaces of large lateral parts of construction bodies with welded 0Kh18N10T steel overlayer. The finishing technology developed reduces the surface roughness from 10 mcm to the standard 2.5 mcm at the efficiency of machining of 2-4 m/sup 2/ per hour.

Aging precipitation behavior and its influence on mechanical properties of Mn18Cr18N austenitic stainless steel

Science.gov (United States)

Qin, Fengming; Li, Yajie; He, Wenwu; Zhao, Xiaodong; Chen, Huiqin

2017-11-01

The aging precipitation behavior in Mn18Cr18N austenitic stainless steel was investigated at temperatures from 600 °C to 900 °C. During isothermal aging treatment, the primary precipitate was Cr2N with a = 0.478 nm and c = 0.444 nm, and it preferentially nucleates along initial grain boundaries and gradually grows towards the interior of grains in discontinuous cellular way. Meanwhile, a small amount of granular face-centred cubic M23C6 with a = 1.066 nm also were observed, which mainly form along grain boundaries. The effect of these precipitates on mechanical properties of the alloy was studied. It was found that precipitates result in degeneration of the matrix hardness. Meanwhile, the SEM morphologies of aged tensile sample show that the brittle fracture predominates during deformation, i.e. the fracture mode transforms from intergranular fracture to transgranular fracture with the increasing of aging time. Compared with the solution-treated sample, the strength of the aged tensile samples slightly decreases and plasticity remarkably deteriorates.

On the adsorption-induced fatigue of structural steels in the presence of alcohols

International Nuclear Information System (INIS)

Loboiko, V.I.; Karpenko, G.V.; Vasilenko, I.I.

1976-01-01

The purpose of the work was to study he effect of anhydrous alcohols on the cyclic fatigue of steels in the absence of contact of the alcohol with atmospheric moisture during the testing process. A vacuum was created in the operating space and then the vacuum annealing was carried out in a bath with the sample and through metal vacuum connection the bath was filled with anhydrous alcohol. Studies were made on several construction steels (20Kh, 40Kh, 50Kh, and ShKh15); steels 40Kh, 50Kh, and ShKh15 were quenched from 840-860 0 C in oil and then tempered at 200 0 C (2 h), steel 20Kh was studied in the as-received state. It was shown that with increase in the carbon content of steel with a martensite structure, the decrease in strength in the presence of anhydrous alcohol was greater than in dry air. Experiments showed that anhydrous alcohol causes an adsorption decrease in the strength both of samples with preliminarily formed cracks and V-shaped stress concentrators and of smooth samples. The greatest adsorption effect of alcohols in our case, as in static fatigue, was observed in samples with cracks. A dependence was shown between the length of the carbon chain and the fatigue limit. This dependence indicates the monotone nature of the decrease in the fatigue limit with transfer from methyl to butyl and then to octyl alcohol

Annealing effect on restoration of irradiation steel properties

International Nuclear Information System (INIS)

Vishkarev, O.M.; Kolesova, T.N.; Myasnikova, K.P.; Pecherin, A.M.; Shamardin, V.K.

1986-01-01

The effect of temperature and annealing time on the restoration of properties of the 15Kh2NMFAA and 15Kh2MFA steels after irradiation at 285 deg with the fluence of 6x10 23 neutr/m 2 (E>0.5 MeV) is studied. Microhardness (H μ ) restoration in the irradiated 15Kh2NMFAA steel is shown to start from 350 deg C annealing temperature. The complete microhardness restoration is observed at the annealing temperature of 500 deg C for 10 hours

Low-temperature nitriding of austenitic steel in a vibrofluidized bed

Science.gov (United States)

Baraz, V. R.; Grachev, S. V.

1999-11-01

The prospects for use of a vibrofluidized bed (VFB) for low-temperature nitrogen saturation of high-strength austenitic steel based on Cr-Ni-Mn (12Kh17N8G2S2MF) are considered. The positive effect of preliminary plastic deformation on the intensity of nitriding is described. The temperature and time parameters of nitriding in a VFB for strain-aging austenitic steel 12Kh17N8G2S2MF are shown to be adequate for the regimes of the final heat-treatment operation of aging. This creates the possibility of combining the operations of surface alloying and strain aging into a single cycle. This combined treatment increases substantially the resistance of the steel to cyclic loads while preserving the strength parameters. It is shown that the presented method of low-temperature nitriding in a VFB is expedient for improving the service characteristics of austenitic steel 12Kh17N8G2S2MF used for production of force springs of automobile brake systems.

Microstructure of reactive synthesis TiC/Cr18Ni8 stainless steel bonded carbides

Institute of Scientific and Technical Information of China (English)

Jiang Junsheng; Liu Junbo; Wang Limei

2008-01-01

TiC/Cr18Ni8 steel bonded carbides were synthesized by vacuum sintering with mixed powders of iron, ferrotitanium, ferrochromium, colloidal graphite and nickel as raw materials. The microstructure and microhardness of the steel bonded carbides were analyzed by scanning electron microscope (SEM),X-ray diffraction (XRD) and Rockwell hardometer. Results show that the phases of steel bonded carbides mainly consist of TiC and Fe-Cr-Ni solid solution. The synthesized TiC particles are fine. Most of them are not more than 1 μm With the increase of sintering temperature, the porosity of TiC/Cr18Ni8 steel bonded carbides decreases and the density and hardness increase, but the size of TiC panicles slightly increases. Under the same sintering conditions, the density and hardness of steel bonded carbides with C/Ti atomic ratio 0.9 are higher than those with C/Ti atomic ratio 1.0.The TiC particles with C/Ti atomic ratio 0.9 are much finer and more homogeneous.

Tensile strength and creep behaviour of austenitic stainless steel type 18Cr - 12Ni with niobium additions at 700{sup 0}C

Energy Technology Data Exchange (ETDEWEB)

Sordi, V L; Bueno, L O, E-mail: sordi@ufscar.b [Federal University of Sao Carlos, Materials Engineering Department, Sao Carlos (SP), 13565-905 (Brazil)

2010-07-01

The effect of niobium additions up to 2.36 wt% on the creep behavior of a series of seven extra low carbon 18Cr-12Ni austenitic stainless steels at 700{sup 0}C has been investigated. Grain size and hardness measurements, hot tensile tests and constant stress creep tests from 90 to 180 MPa were carried out for each alloy, in the solution treated condition at 1050, 1200 and 1300{sup 0}C followed by quench in water. The mechanical behavior at high temperature was related to the amount of NbC precipitation occurring during the tests. Solid solution and intermetallic compound effects were also considered. Creep data analysis was done to determine the parameters of the creep power-law equation {epsilon}-dot = A.{sigma}{sup n} and the Monkman-Grant relation {epsilon}-dot .t{sup m}{sub R} = K. Niobium-carbide precipitation in these steels reduces the secondary stage dependence of strain rate with applied stress, resulting in n-values which indicate the possibility of operation of various creep mechanisms. The creep strength during the secondary stage is primarily controlled by the amount of NbC available for precipitation. However, the rupture times increase progressively with niobium content, as the amount of undissolved carbide particles in grain boundaries and the Laves phase precipitation increase.

Phosphorus effect on fracture properties of structural steels

International Nuclear Information System (INIS)

Goritskij, V.M.; Guseva, I.A.

1985-01-01

Phosphorus content is studied for its effect on fracture peculiarities and fracture toughness. It is supposed that the phosphorus effect on ductile fractures is associated with phosphorus segregation on the ferrite-carbide interfaces. An increase of the phosphorus content in heat-treated 10KhSND steel from 0.020 up to 0.043 wt.% results in a decrease of the pore size and asub(p) value. Close linear correlation is established between critical temperature of embrittlement T 50 and √ asub(p) or √ KC values for a number of structural steels with different phosphorus content

Structural features and properties of the laser-deposited nickel alloy layer on a KhV4F tool steel after heat treatment

Science.gov (United States)

Shcherbakov, V. S.; Dikova, Ts. D.; Stavrev, D. S.

2017-07-01

The study and application of the materials that are stable in the temperature range up to 1000°C are necessary to repair forming dies operating in this range. Nickel-based alloys can be used for this purpose. The structural state of a nickel alloy layer deposited onto a KhV4F tool steel and then heat treated is investigated. KhV4F tool steel (RF GOST) samples are subjected to laser deposition using a pulsed Nd:YAG laser. A nickel-based material (0.02C-73.8Ni-2.5Nb-19.5Cr-1.9Fe-2.8Mn) is employed for laser deposition. After laser deposition, the samples are subjected to heat treatment at 400°C for 5 h, 600°C for 1 h, 800°C for 1 h, and 1000°C for 1 h. The microstructure, the phase composition, and the microhardness of the deposited layer are studied. The structure of the initial deposited layer has relatively large grains (20-40 μm in size). The morphology is characterized by a cellular-dendritic structure in the transition zone. The following two structural constituents with a characteristic dendritic structure are revealed: a supersaturated nickel-based γ solid solution and a chromium-based bcc α solid solution. In the initial state and after heat treatment, the hardness of the deposited material (210-240 HV 0.1) is lower than the hardness of the base material (400-440 HV 0.1). Only after heat treatment at 600°C for 1 h, the hardness increases to 240-250 HV0.1. Structure heredity in the form of a dendritic morphology is observed at temperatures of 400, 600, and 800°C. The following sharp change in the structural state is detected upon heat treatment at 1000°C for 1 h: the dendritic morphology changes into a typical α + γ crystalline structure. The hardness of the base material decreases significantly to 160-180 HV 0.1. The low hardness of the deposited layer implies the use of the layer material in limited volume to repair the forming surfaces of dies and molds for die casting. However, the high ductility of the deposited layer of the nickel

Effect of aging on the tribological and mechanical properties of a high-nitrogen stainless austenitic steel

International Nuclear Information System (INIS)

Korshunov, L.G.; Chernenko, N.L.; Tereshchenko, N.A.; Uvarov, A.I.

2005-01-01

The effect of aging, associated with predominant precipitation of vanadium nitrides (VN), on tribological and mechanical properties of austenitic steel 10Kh18AG18N5MF hardened from 1100 Deg C is studied. Metallographic, X-ray diffraction and electron microscopical methods are used to study structural transformations proceeding in the steel on aging as well as on friction loading under conditions of dry slipping friction in steel-abrasive and steel-steel pairs. It is shown that the aging at temperatures of 600-700 Deg C resulting in a considerable increase of strength properties of the steel demonstrates a relatively weak positive effect on steel resistance to abrasive and adhesive wear. It is stated that the use of aging by continuous mechanism permits attaining favourable mechanical and tribological properties in vanadium-alloying nitrogen-bearing austenitic steels [ru

Effect of rhenium and osmium on mechanical properties of a 9Cr-2W-0.25V-0.07Ta-0.1C steel

International Nuclear Information System (INIS)

Klueh, R.L.; Alexander, D.J.; Sokolov, M.A.

2000-01-01

The nuclear transmutation of tungsten to rhenium and osmium in a tungsten-containing steel irradiated in a fission or fusion reactor will change the chemical composition of the steel. To determine the possible consequences of such compositional changes on the mechanical properties, tensile and Charpy impact properties were measured on five 9Cr-2W-0.25V-0.07Ta-0.1C steels that contained different amounts of rhenium, osmium, and tungsten. The mechanical properties changes caused by these changes in composition were minor. Observations were also made on the effect of carbon concentration. The effect of carbon on tensile behavior was minor, but there was a large effect on Charpy properties. Several of the steels showed little effect of tempering temperature on the Charpy transition temperature, a behavior that was tentatively attributed to the low silicon and/or manganese concentration of the experimental steels

[Effect of KH2PO4 on the odonto- and osteogenic differentiation potential of human stem cells from apical papillae].

Science.gov (United States)

Wang, Yan-ping; Wu, Jin-tao; Wang, Zi-lu; Zheng, Yang-yu; Zhang, Guang-dong; Yu, Jin-hua

2013-01-01

To determine the effects of KH2PO4 on the odonto- and osteogenic differentiation potential of human stem cells from apical papillae (SCAP) in vitro. SCAP were isolated and cultured respectively in alpha minimum essential medium (α-MEM) or α-MEM containing 1.8 mmol/L KH2PO4. Alkaline phosphatase (ALP) activity, alizarin red staining, real-time reverse transcription polymerase chain reaction (RT-PCR) and Western blotting were used to examine the odonto and osteogenic potential of SCAP in the two media. SCAP cultured in α-MEM containing 1.8 mmol/L KH2PO4 exhibited a higher ALP activity [(0.370 ± 0.013) Sigma unit×min(-1)×mg(-1)] at day 3 than control group [(0.285 ± 0.008) Sigma unit×min(-1)×mg(-1)] and KH2PO4-treated SCAP formed more calcified nodules at day 5 [(0.539 ± 0.007) µg/g] and day 7 [(1.617 ± 0.042) µg/g] than those in normal medium [(0.138 ± 0.037) µg/g, P odonto- and osteogenic markers were significantly up-regulated after the stimulation of KH2PO4 at day 3 and 7 respectively, as compared with control group. 1.8 mmol/L KH2PO4 can promote the odonto and osteogenic differentiation potential of human SCAP.

Investigation programme and procedure for creep and long-term rupture strength in materials with accounting for stress deviator and loading history

International Nuclear Information System (INIS)

Mozharovskaya, T.N.

1984-01-01

A programme and procedure are given to study 08Kh18N9 steel at 600 deg C and 15Kh2MFA steel at 550 deg C for creep and long-term strength at different parameters of proportional loading as well as at different parameters under loading in two-link irregular trajectories. This makes it possible to estimate the effect of the kind of a stress deviator, history and prehistory of loading on plastic deformation in creep and on failure under long-term loading

Investigation programme and procedure for creep and long-term rupture strength in materials with accounting for stress deviator and loading history

Energy Technology Data Exchange (ETDEWEB)

Mozharovskaya, T N [AN Ukrainskoj SSR, Kiev. Inst. Problem Prochnosti

1984-11-01

A programme and procedure are given to study 08Kh18N9 steel at 600 deg C and 15Kh2MFA steel at 550 deg C for creep and long-term strength at different parameters of proportional loading as well as at different parameters under loading in two-link irregular trajectories. This makes it possible to estimate the effect of the kind of a stress deviator, history and prehistory of loading on plastic deformation in creep and on failure under long-term loading.

Effect of the radiation in the reference temperature T0 in ferritic steel

International Nuclear Information System (INIS)

Villanueva O, A.; Gachuz M, M.E.

2004-01-01

The present work studies the effect that produces the irradiation in ferritic steels (AISI 8620) on the reference temperature (T 0 ) that characterizes the tenacity to the fractures (K JC ) of these materials obtaining this way a characteristic curve (Master Curve) of this steel. The approach of the 'Master curve' is based on the Astm E-1921. Following this standard the methodology of a sub size settled down in Charpy type test tubes. Due to this type of steels is used mainly in pressure vessels of the reactor in Nuclear Power plants, the fracture tenacity gives the rule at the moment for the verification of structural integrity of the pressure vessel of the reactor. (Author)

Radiation embrittlement of WWER 440 pressure vessel steel and of some improved steels by western producers

International Nuclear Information System (INIS)

Koutsky, J.; Vacek, M.; Stoces, B.; Pav, T.; Otruba, J.; Novosad, P.; Brumovsky, M.

1982-01-01

The resistance was studied of Cr-Mo-V type steel 15Kh2MFA to radiation embrittlement at an irradiation temperature of around 288 degC. Studied was the steel used for the manufacture of the pressure vessel of the Paks nuclear reactor in Hungary. The obtained results of radiation embrittlement and hardening of steel 15Kh2MFA were compared with similar values of Mn-Ni-Mo type steels A 533-B and A 508 manufactured by leading western manufacturers within the international research programme coordinated by the IAEA. It was found that the resistance of steel 15Kh2MFA to radiation embrittlement is comparable with steels A 533-B and A 508 by western manufacturers. (author)

Mechanical properties of irradiated 9Cr-2WVTa steel

International Nuclear Information System (INIS)

Klueh, R.L.; Alexander, D.J.; Rieth, M.

1998-01-01

An Fe-9Cr-2W-0.25V-0.07Ta-0.1C (9Cr-2WVTa) steel has excellent strength and impact toughness before and after irradiation in the Fast Flux Test Facility and the High Flux Reactor (HFR). The ductile-brittle transition temperature (DBTT) increased only 32 C after 28 dpa at 365 C in FFTF, compared to a shift of ∼60 C for a 9Cr-2WV steel--the same as the 9Cr-2WVTa steel but without tantalum. This difference occurred despite the two steels having similar tensile but without tantalum. This difference occurred despite the two steels having similar tensile properties before and after irradiation. The 9Cr-2WVTa steel has a smaller prior-austenite grain size, but otherwise microstructures are similar before irradiation and show similar changes during irradiation. The irradiation behavior of the 9Cr-2WVTa steel differs from the 9Cr-2WV steel and other similar steels in two ways: (1) the shift in DBTT of the 9Cr-2WVTa steel irradiated in FFTF does not saturate with fluence by ∼28 dpa, whereas for the 9Cr-2WV steel and most similar steels, saturation occurs at <10 dpa, and (2) the shift in DBTT for 9Cr-2WVTa steel irradiated in FFTF and HFR increased with irradiation temperature, whereas it decreased for the 9Cr-2WV steel, as it does for most similar steels. The improved properties of the 9Cr-2WVTa steel and the differences with other steels were attributed to tantalum in solution

Exclusive brachytherapy for T1-T2 N0 cancer of the oral tongue: prognostic factors for local control

International Nuclear Information System (INIS)

Frezza, G.; Baldissera, A.; Bunkheila, F.; Caliceti, U.; Galuppi, A.; Guidetti, A.; Sorrenti, G.

1996-01-01

INTRODUCTION: The files of a group of patients (pts) treated with brachytherapy alone for cancer of the oral tongue were reviewed to assess the prognostic role of T stage, volume of disease, total dose and dose-rate. PATIENTS METHODS AND RESULTS: From 1982 to 1994 46 pts (29 males, 17 females, age 38-84 years, median 63.1 years) were treated with 192 Ir brachytherapy, in 2 cases followed by prophylactic neck dissection for cancer of the oral tongue (T1N0: 19 pts; T2N0: 27 pts). Brachytherapy was performed with hairpins in the early years of the study (17 pts) and more recently with plastic tubes (29 pts), according to the Parts System. Dose ranged from 60-70 Gy with a dose-rate of 0.38-0.62 Gy/h (median 63.8 and 0.52 respectively). Volume of the disease was retrospectively assessed as the product of the three diameters of the lesion calculated for provisional dosimetry (range 0.25- 16 cc.). Median follow up is 72 mos (range: 14-153 mos). RESULTS: Overall local control was 82.6% ((38(46)) pts; T1: (18(19)), 94.7 %; T2: (22(27)), 81.5 %). Five of 8 pts who recurred were submitted to salvage surgery, and 3 of them are alive and free from disease at 34, 52 and 87 mos respectively. Recurrences appeared after 3-13 mos (median 5.5 mos) and were related to total dose ( 63 Gy (1(18)); 5.5 %) and to dose-rate ( 45 cGy/h (4(36)): 11.1 %). The volume of disease was not of prognostic significance since local control was 79.6 % ((6(28)) pts) in pts with a disease smaller than 3 cc. and 88.9 % in pts with large volume ((2(18)) pts). Seven (15.2 %) grade 3 complications (necrosis of the mandibular bone and- or of the soft tissues) were observed. Complication rate was higher in the high dose group (>63 Gy (4(18)) pts: 22.2 %) and was less affected by dose-rate (> 45 cGy/h (6(36)) pts: 16.6 %). No relationship between complications and volume was observed ( 3cc.: 16.6 %). All complications healed spontaneously. DISCUSSION AND CONCLUSION: For T1-T2 cancer of the oral tongue exclusive

Structure and properties of joints of two-ply steel using ''elastic'' explosives

International Nuclear Information System (INIS)

Gel'man, A.S.; Savel'ev, S.A.; Kulakevich, Ya.S.; Sharypov, N.A.; Drogovejko, I.Z.; Domolego, I.E.

1980-01-01

Some experimental data on structure and properties of compounds during cladding of sheets made of St3 with sheets of nichrome and steel 12Kh18N10T with the use of ''elastic'' explosives are presented. It is shown that the use of ''elastic'' explosives permits to decrease r parameter sufficiently, (where r - is the ratio of explosive mass to the mass of throwen phate) that reduces considerably the specific consumption explosives in comparison with the consumption conventional mixture explosives. Peculiarities of tested ''elastic'' explosives make their application perspective in two cases - at cladding of complex curved surfaces (drums, tube blanks etc.), as sell as at applications of burst chambers, where explosive mass limits dimensions of cladding blanks and details [ru

Susceptibility to stress corrosion in stainless steels type AISI 321 and 12X18H10T used in PWR type reactors (WWER); Susceptibilidad a la corrosion bajo esfuerzo de barras de acero inoxidable AISI 321 y 12X18H10T en ambientes utilizados en reactores VVER

Energy Technology Data Exchange (ETDEWEB)

Matadamas C, N

1996-12-31

Titanium stabilized stainless steels have been utilized in sovietic pressurized water reactors (VVER) for avoid the susceptibility to Intergranular Corrosion (IGC) present in other austenitic stainless steels. However the Intergranular Corrosion resistance of this kind of materials has been questioned because of Intergranular Stress Corrosion Cracking failures (IGSCC) have been reported. This paper study the electrochemical behavior of the AISI 321 stainless steel in a H{sub 3}BO{sub 3} Solution contaminated with chlorides and its susceptibility to Intergranular Corrosion.Electrochemical prediction diagrams of the stainless steels AISI 321 and 12X18H10T (sovietic) sensitized (600 Centigrade, 3 h.) were compared. Cylindrical and conical samples were used in Slow Strain Rate Tests (SSRT), to determine the susceptibility to Stress Corrosion Cracking (SCC) in AISI 321 and 12X18H10T stainless steels. The results obtained showed that the temperature of the solution is a very important factor to detect this susceptibility. Fractography studies on the fracture surfaces of the samples obtained in the SSRT at high temperature were realized. Corrosion velocities of both AISI 321 and 12X18H10T stainless steels were determined using conical samples in the CERT system at high temperature. E.D.A.X. analysis was employed in both AISI 321 and 12X18H10T stainless steels in order to explain the degree of sensitization. (Author).

Effect of reactor irradiation on long-term strength and creep of 0Kh16N15M3B steel under plane stressed state

International Nuclear Information System (INIS)

Khristov, G.P.; Kosov, B.D.

1982-01-01

The paper deals with analysis of results of experimental studies in creep of the austenitic OKh16n15m3b steel with various size of initial-structure grain under conditions of high-intensity reactor irradiation and control tests. It is suggested to consider the material initial structure effect on intensity of minimum creep rates both under ordinary and intrareactor conditions of loading by means of the function grain size effect on the equivalent stress. It is shown that the criterial expression previously suggested by the authors is invariant to the type of stressed and structural states and relative to intensity of minimal creep rates. It is established that the creep rate of the irradiated steel may be calculated from dependence for nonirradiated steel using as an argument a certain reduced equivalent stress which is a function of the acting stress and irradiation parameter

The entire mean stress relaxation effects of 0Cr18Ni10Ti piping steel

International Nuclear Information System (INIS)

Yang Bing; Zhao Yongxiang

2005-01-01

Experimental study is performed on the mean stress relaxation effects of the Chinese new piping material, 0Cr18Ni10Ti steel. Six sets of specimens are respectively fatigued under a strain-controlled mode with the six straining ratios (R ε ) of -1, -0.52, -0.22, 0.029, 0.18, and 0.48 by an improved test method implied with an maximum likelihood statistical principle. The test results reveal that the material exhibits a Masing behaviour and, surprisingly, involves an entire mean stress relaxation. A challenge is then emerging to the traditional same treat of straining ratio and stressing ratio (R σ ) in fatigue analysis and assessment. There is still no effective method to describe this kind of relaxation. However the R ε effects can represent the relaxation effects appropriately by investigation on the material random cyclic stress-strain (σ-ε) relations and strain-life (ε-N) relations with different R ε . The intrinsic randomness of the responses is taken into account on a probabilistic sense. Significant differences are observed of the material cyclic responses under different R ε . For σ-ε relations, the R ε effects act as a decreasing trend to the stress amplitudes with the increasing survival probability and confidence. The strongest effect appears at R ε of 0.029, and a weaker one acts as R ε is far away from zero. For ε-N relations, R ε greater than zero exhibits a positive effect on the fatigue lives of about 1.3 to 1.6 times under a survival probability of 0.999 and a confidence of 95%, while a negative effect is exhibited in case of R ε less than zero. Present work indicates that systematic researches should be made to give a reasonable fatigue prediction in service on a basis of cyclic strain inspection of structures. (authors)

Influence of Mn contents in 0Cr18Ni10Ti thin wall stainless steel tube on TIG girth weld quality

Science.gov (United States)

Liu, Bo

2017-03-01

Three kinds of cold worked 0Cr18Ni10Ti thin wall stainless steel tubes with the manganese contents of 1.27%, 1.35% and 1.44% and the cold worked 0Cr18Ni10Ti stainless steel end plug with manganese content of 1.35% were used for TIG girth welding in the present investigation. The effect of different manganese contents in stainless steel tube on weld quality was studied. The results showed that under the same welding conditions, the metallographic performance of the girth weld for the thin wall stainless steel tube with the manganese element content 1.44% welded with end plug was the best. Under the appropriate welding conditions, the quality of the girth weld increased with the increase of the manganese content till 1.44%. It was found that in the case of the Mn content of 1.44%, and under the proper welding condition the welding defects, such as welding cracks were effectively avoided, and the qualified weld penetration can be obtained.. It is concluded that the appropriate increase of the manganese content can significantly improve the TIG girth weld quality of the cold worked 0Cr18Ni10Ti stainless steel tube.

Structural steels for power generating equipment and heat and chemical heat treatments

International Nuclear Information System (INIS)

Astaf'ev, A.A.

1979-01-01

Development of structural steels for power generating equipment and for reactor engineering, in particular, is elucidated. Noted is utilization of the 15Kh2NMFA steels for the WWER-1000 reactor vessels, the 10GN2MFA steels for steam generators, pressurizers, vessels of the automatic emergency shut down and safety system; the 00Kh12N3DL steel for cast pump vessels and main locking bars. The recommendations on heat treatment of big forgings, for instance, ensuring the necessary complex of mechanical properties are given. Diffusion chromizing with subsequent nitriding of austenitic steels which increase durability of the components in BN reactors more than 4 times, is practised on a large scale

Structural changes in complex steels with 12 % Cr during welding thermal cycle

International Nuclear Information System (INIS)

Ul'yanova, N.V.; Kurnosova, N.D.

1981-01-01

The structural changes in the heat affected zones of welded steam tubes of the 12Kh11V2MF and 18Kh12VMBFR steels, are investigated. A short-time heating of thin samples up to 1300-900 deg C with the aim of imitating the thermal welding cycle permits to determine temperatures of specific region formation in heat affeced zones of 12% Cr steels. The difference in the amounts and structure of σ-ferrite and γ-phase in these regions is established. A ''tongue'' nature of γ-phase grain growth is found in the temperature range of 1150-1100 deg C, while at 1300-1250 deg C σ-ferrite growth with the formation of saw-shape boundaries is observed. It is shown that tensile properties of imitated heat affected zone of 12Kh12VMBFP steel increase with heating temperature with the insignificant plasticity decrease. Impact strength on longitudinal samples decreases but remains higher than that determined by specifications [ru

Corrosion resistance of chromium-nickel steel containing rare earths

International Nuclear Information System (INIS)

Asatiani, G.N.; Mandzhgaladze, S.N.; Tavadze, L.F.; Chuvatina, S.N.; Saginadze, D.I.

1983-01-01

Effect of additional out-of-furnace treatment with complex alloy (foundry alloy) calcite-silicon-magnesium-rare earth metal on corrosion resistance of the 03Kh18N20M3D3C3B steel has been studied. It is shown that introduction of low additions of rare earths improves its corrosion resistance improves its corrosion resistance in agressive media (in 70% - sulfuric acid) in the range of transition from active to passive state. Effect of additional introduction of rare earth metals is not considerable, if potential of steel corrosion is in the range of stable passive state (32% - sulfuric acid). Additional out-of-furnace treatment with complex foundry alloy, containing rare earth metals, provides a possibility to use a steel with a lower content of Cr, Ni, Mo, than in conventional acid-resistant steels in highly agressive media

T1N0 to T2N0 Squamous Cell Carcinoma of the Glottic Larynx Treated With Definitive Radiotherapy

International Nuclear Information System (INIS)

Chera, Bhishamjit S.; Amdur, Robert J.; Morris, Christopher G.; Kirwan, Jessica M.; Mendenhall, William M.

2010-01-01

Purpose: To report the treatment outcomes of definitive radiotherapy (RT) for early-stage squamous cell carcinoma (SCCA) of the glottic larynx. Methods and Materials: We retrospectively reviewed the medical records of 585 patients with T1N0 to T2N0 invasive SCCA of the glottic larynx treated between 1964 and 2006 with RT alone. All patients had at least 2 years of follow-up, had histologic diagnosis of invasive SCCA, and received continuous-course RT. None of these patients received chemotherapy or had elective nodal RT. The probabilities of local control (LC), ultimate LC, ultimate LC with larynx preservation, neck control, cause-specific survival (CSS), and overall survival (OS) were calculated by the Kaplan-Meier product-limit method. Results: The median follow-up for survivors was 12 years. Five-year LC rates were as follows: T1A, 94%; T1B, 93%; T2A, 80%; and T2B, 70%. Multivariate analysis revealed that overall treatment time greater than 41 days (p = 0.001) and poorly differentiated histology (p = 0.016) adversely affected LC. Five-year rates of ultimate LC with laryngeal preservation were: T1A, 95%; T1B, 94%, T2A, 81%; and T2B, 74%. Twenty-four (4%) of 585 patients failed in the neck; only 7 neck failures (1%) were isolated. Five-year CSS and OS rates were as follows: T1A, 97% and 82%; T1B, 99% and 83%; T2A, 94% and 76%; and T2B, 90% and 78%, respectively. Ten (1.7%) patients had severe and/or fatal complications. One patient died of a radiation-induced carotid artery angiosarcoma. Conclusion: Based on our study results, RT cures a high proportion of patients with T1N0 to T2N0 glottic SCCAs and has a low rate of severe complications.

Synergistic enhancing effect of N+C alloying on cyclic deformation behaviors in austenitic steel

Energy Technology Data Exchange (ETDEWEB)

Kang, J. [State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004 (China); Zhang, F.C., E-mail: zfc@ysu.edu.cn [State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004 (China); Long, X.Y. [State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004 (China); Yang, Z.N. [National Engineering Research Center for Equipment and Technology of Cold Strip Rolling, Yanshan University, Qinhuangdao 066004 (China)

2014-07-29

Cyclic plastic and elastic strain controlled deformation behaviors of Mn18Cr7 austenitic steel with N0.6C0.3 synergistic enhancing alloying have been investigated using tension-compression low cycle fatigue and three-point bending high cycle fatigue testing. Results of cyclic deformation characteristic and fatigue damage mechanism have been compared to that in Mn12C1.2 steel. Mn18Cr7N0.6C0.3 steel always shows cyclic softening caused by enhanced planar sliding due to the interaction between N+C and the substitutional atoms as well as the dislocation, which is totally different from cyclic hardening in Mn12C1.2 steel caused by the interaction between C members of C–Mn couples with the dislocation. Enhanced effective stress is obtained due to the solid solution strengthening effect caused by the short range order at low strain amplitude while this effect does not work at high strain amplitude. Internal stress contributes most to the cyclic softening with the increase of strain amplitudes. Significant planar slip characteristic can be observed resulting from low stacking fault energy and high short range order effects in Mn18Cr7N0.6C0.3 steel and finally the parallel or intersecting thin sheets with dislocation tangles separated by dislocation free sheets are obtained with the prolonged cycles under cyclic elastic or plastic strain controlled fatigue testing. There exist amounts of small cracks on the surface of the Mn18Cr7N0.6C0.3 steel because fatigue crack initiation is promoted by the cyclic plastic strain localization. However, the zigzag configuration of the cracks reveals that the fatigue crack propagation is highly inhibited by the planar slip characteristic, which eventually improves the fatigue life.

KH in Paraffin - KH(P): A Useful Base for Organic Synthesis

Science.gov (United States)

Taber, Douglass F.; Nelson, Christopher G.

2011-01-01

The preparation of KH as a one:one homogenate with paraffin, termed KH(P), is reported. KH(P), a solid at room temperature, is stable without special handling. On suspension in THF with a phosphonium salt, KH(P) rapidly generates the ylide. Wittig condensation with aromatic, aliphatic and α, β-unsaturated aldehydes proceeds with high Z-selectivity. KH(P) should be a generally useful base for organic synthesis. PMID:17081034

Quality of the KhN73MBTYu alloy after electroslag remelting and vacuum arc remelting

International Nuclear Information System (INIS)

Shelgaeva, A.V.; Krichevets, M.I.; Shinkina, N.S.; Komissarov, A.I.

1978-01-01

The structure and properties of the heat-resisting KhN73MBTYu alloy are investigated after electroslag remelting (ESR) and vacuum arc (VAR) remelting in commercial furnaces. The complex investigations of the casted metal were carried out by modern methods along with the standard acceptance tests, and a number of service properties were determined. It is established that the ESR metal contains magnesium and has the reduced sulphur concentration; the alloy has more fine-grained structure at high isotropy of the properties at room and operating temperatures; higher endurance is achieved under reversal rotational bending; no laminated fractures are observed. According to the basic quality factors the ESR metal satisfies all requirements for the VAR metal. Due to exclusion of strippling of ESR electrodes and ingots the yield of steel forgings increases by 20-25% and the prime cost decreases in comparison with the industrial production of VAR metal

Microstructural characterization of 5-9% chromium reduced-activation steels

International Nuclear Information System (INIS)

Jayaram, R.; Klueh, R.L.

1997-01-01

The microstructures of a 9Cr-2W-0.25-0.1C (9Cr-2WV), a 9Cr-2W-0.25V-0.07Ta-0.1C (9Cr-2WVTa), a 7Cr-2W-0.25V-0.07Ta-0.1C (7Cr-2WVTa), and a 5Cr-2W-0.25V-0.07Ta-0.1C (5Cr-2WVTa) steel (all compositions are in weight percent) have been characterized by Analytical Electron Microscopy (AEM) and Atom Probe Field Ion Microscopy (APFIM). The matrix in all four reduced-activation steels was 100% martensite. In the two 9Cr steels, the stable precipitates were blocky M 23 C 6 and small spherical MC. The two lower-chromium steels contained blocky M 7 C 3 and small needle-shaped carbonitrides in addition to M 23 C 6 . AEM and APFIM analysis revealed that in the steels containing tantalum, the majority of the tantalum was in solid solution. The experimental observations were in good agreement with phases and compositions predicted by phase equilibria calculations

Z-phase in 9-12% Cr Steels

DEFF Research Database (Denmark)

Danielsen, Hilmar; Hald, John

2004-01-01

The complex nitride Z-phase, Cr(V,Nb)N, has recently been identified as a major cause for premature breakdown in creep strength of a number of new 9-12%Cr martensitic steels. A thermodynamic model of the Z-phase has been created based on the Thermo-Calc software. The model predicts the Z-phase to......The complex nitride Z-phase, Cr(V,Nb)N, has recently been identified as a major cause for premature breakdown in creep strength of a number of new 9-12%Cr martensitic steels. A thermodynamic model of the Z-phase has been created based on the Thermo-Calc software. The model predicts the Z......-phase to be stable in all of the new 9-12%Cr martensitic steels. This has generally been confirmed by the performed experiments. Z-phase precipitation seems to be a kinetic problem, and drivning force calculations using Thermo-Calc with the developed model have been used to predict steel compositions, which...

Ductile fracture of two-phase welds under 77K

International Nuclear Information System (INIS)

Yushchenko, K.A.; Voronin, S.A.; Pustovit, A.I.; Shavel', A.V.

1984-01-01

The effect of the type of welding and fillers on crack resistance of welded joints high-strength steel EhP810 and its various compounds with steels EhP666, 08Kh18N10T has been studied. For the welding of steel EhP810 with steels EhP810, EhP666, 08Kh18N10T electron-beam, automatic, argon tungsten arc with non-consumable electrode with various fillers, as well as argon metal-arc welding with consumable electrode, were used. It is shown, that for a joint, made by electron-beam welding, parameters σsub(u), Ksub(IcJ), KCV are higher than for a joint of a similar phase structure made using filler wire EhP659-VI. It is explained by the fact, that during electron-beam welding joint metal refining takes place, which removes gases. In welded joints of chP810 steel, having joints with austenitic structure, characteristic of crack resistance Ssub(c) increases by more than 0.2 mm in contrast to two-phase joints, which conventional yield strength at 77 K exceeds 1000 MPa. It is worth mentioning, that for other classes of steels formation of two-phase structure of joint increases welded joint resistance to brittle fracture. It is possible to obtain the required structure of joint with assigned level of resistance to brittle fracture by means of the use of different fillers, optimum and welding procedure, regulaing the part of the basic metal in joint content

Peculiar features of determination of plastic properties in bimetals

International Nuclear Information System (INIS)

Voronin, A.V.; Zhadan, V.T.; Osadchij, V.A.; Rumyantsev, A.V.

1993-01-01

Method for calculating relative elongation of sheet bimetal on the basis of data of plastic characteristics of bimetal components has been developed. Results of calculation according to suggested method differ slightly from experimental values. It was shown analytically and supported by experiments (taking St3+12Kh18N10T samples, 45+Kh12 steel as examples), that the value of bimetal area reduction coincides with the value of area reduction of less plastic component

Development of production technology and investigation of quality for forged-welded turbine rotors of steel 25Kh2NVFA

International Nuclear Information System (INIS)

Borisov, I.A.; Merinov, G.N.; Slezkina, E.V.

1997-01-01

A study was made into mechanical properties and microstructure of turbine rotor components manufactured by forging and heat treated under various conditions. It is revealed that the optimal heat treatment of forgings must include double quenching with subsequent tempering at 630-640 deg C for 10-20 h. Forged and welded rotors should be tempered at 620-630 deg C for 50-100 h. Microscopic examination and mechanical tests showed that low alloy steel 25Kh2NMF can be successfully used for manufacturing rotors of high-, medium-and low-heat turbines

Electron beam welding of flanges with tubular shafts of steel 40KhNMA

International Nuclear Information System (INIS)

Leskov, G.I.; Zhivaga, L.I.; Shipitsyn, B.N.; Savichev, R.V.

1975-01-01

The results are presented of elaborating the technological process for the electron beam welding of flanges with a tube of the 40KhNMA steel and of investigation into the quality of the welded joints. A welded piece has been fabricated conforming to the technology suggested observing the parameters worked-out in the following sequence: assembling the piece; pre-welding of the edges in some points; welding; high tempering; welds quality control; removal of the seam reinforcement inside of the tube and the weld root to the depth of 2 mm; quenching; tempering; welds quality control; finishing. The welds quality control consists in visual inspection, ultrasonic testing, magnetic flaw detection, as well as X-ray and metallographic analyses. The mechanical properties are studied on notched samples cut out of the welded joints. The test results have shown that the mechanical properties of the welded joints meet the requirements on the same level with the base metal

Enhancement of strength properties of hot rolled 10KHSND steel

International Nuclear Information System (INIS)

Nasibov, A.G.; Popova, L.V.; Pikulin, S.A.; Globa, N.I.

1989-01-01

To find out the reasons of low hot rolling yield for 10KhSND steel sheets in mechanical properties, titanium effect in the range of 0.008-0.03% concentrations is studied. It is established that the titanium content in a solid solution is conserved within 0.003-0.005%, the rest of titanium is bound to carbonitrides Ti(C, N). It is shown that alloys with 0.025-0.03% titanium content possess the increased values of ultimate and yield strength the necessary level of impact strength and good wealdability. The good steel yield, when the titanium content is sustained at the given level, increases from 40 to 85%

Study of nitrogen solubility in multicomponent iron alloys at its pressure in gaseous phase up to 1000kPa

International Nuclear Information System (INIS)

Pomarin, Yu.M.; Grigorenko, G.M.; Latash, Yu.V.; Kanibolotskij, S.A.

1983-01-01

A facility in which metal is melted in a weighed state and nitrogen partical pressure during relting may be charge from 0 to 1000 kPa is developed to investigate nitrogen solubility is liquim metals and alloys. Investigation of nitrogen solubility was performed using samples of 03Kh25N5AM3 steel and Kh20N5, Kh20N10, Kh40N10, Kh40N20 alloys. Positive deflection of [N]=f(√Psub(Nsub(2))) dependence from the Henry law is shown to be observed in the Kh40N10 alloy in the 100-1000 kPa pressure range. In this case the vatue of positive deflection decreases with temperature growth and at T=2273 K nitrogen solubility in the alloy submits to the law of square root. An equation permitting to calculate nitrogen solubility in alloys of Fe-Cr-Ni and Fe-Cr-Mn systems in the 0 to 1000 kPa range of nitrogen partial pressures is obtained

Identification of candidates for postmastectomy radiotherapy in patients with pT3N0M0 breast cancer

International Nuclear Information System (INIS)

Hamamoto, Yasushi; Ohsumi, Shozo; Aogi, Kenjiro; Takashima, Shigemitsu; Shinohara, Shuichi; Nakajima, Naomi; Kataoka, Masaaki

2013-01-01

There is still controversy concerning the indication of postmastectomy radiotherapy (PMRT) for pT3N0M0 breast cancer. To identify the candidates for PMRT in this subset, we investigated failure patterns, and searched for risk factors for isolated locoregional failure in pT3N0M0 breast cancer after mastectomy without PMRT. Among 1,176 patients who received mastectomy without PMRT for untreated unilateral breast cancer between 1990 and 2002, 64 patients (5%) had pT3N0M0 breast cancer (age 30-81 years; median 52.5 years). Isolated locoregional failure as the initial failure occurred in three patients. For all 64 patients, the 8-year failure-free survival rate, the isolated locoregional failure-free rate, and the distant failure-free rate were 76, 93, and 82%, respectively. Incidence of isolated locoregional failure as the initial failure was 18% (2/11) for patients 40 years or younger and 2% (1/53) for patients older than 40 years. The 8-year isolated locoregional failure-free rates were 73% for patients 40 years or younger and 98% for patients older than 40 years (p=0.0135). Concerning pT3N0M0 breast cancer, incidence of isolated locoregional failure was comparatively low after mastectomy without PMRT. Routine use of PMRT for all pT3N0M0 patients seemed to be unacceptable. PMRT may be useful for younger patients because of the comparatively high incidence of isolated locoregional failure. Because of the small number of cases in our series, further studies are necessary to determine the usefulness of PMRT for younger patients with pT3N0M0 breast cancer. (author)

Effects of Ti element on the microstructural stability of 9Cr–WVTiN reduced activation martensitic steel under ion irradiation

Energy Technology Data Exchange (ETDEWEB)

Luo, Fengfeng [Key Laboratory of Artificial Micro- and Nano-Structures of Ministry of Education, Hubei Nuclear Solid Physics Key Laboratory and School of Physics and Technology, Wuhan University, Wuhan 430072 (China); Guo, Liping, E-mail: guolp@whu.edu.cn [Key Laboratory of Artificial Micro- and Nano-Structures of Ministry of Education, Hubei Nuclear Solid Physics Key Laboratory and School of Physics and Technology, Wuhan University, Wuhan 430072 (China); Jin, Shuoxue; Li, Tiecheng; Chen, Jihong [Key Laboratory of Artificial Micro- and Nano-Structures of Ministry of Education, Hubei Nuclear Solid Physics Key Laboratory and School of Physics and Technology, Wuhan University, Wuhan 430072 (China); Suo, Jinping; Yang, Feng [State Key Laboratory of Mould Technology, Institute of Materials Science and Engineering, Huazhong University of Science and Technology, Wuhan 430074 (China); Yao, Z. [Department of Mechanical and Materials Engineering, Queen’s University, Kingston K7L 3N6, ON (Canada)

2014-12-15

Microstructure of 9Cr–WVTiN reduced-activation martensitic steels with two different Ti concentrations irradiated with Fe{sup +}, He{sup +} and H{sup +} at 300 °C was studied with transmission electron microscopy. Small dislocation loops were observed in the irradiated steels. The mean size and number density of dislocation loops decreased with the increase of Ti concentration. The segregation of Cr and Fe in carbides was observed in both irradiated steels, and the enrichment of Cr and depletion of Fe were more severe in the low Ti-concentration 9Cr–WVTiN steel.

Microstructural characterization of 5-9% chromium reduced-activation steels

Energy Technology Data Exchange (ETDEWEB)

Jayaram, R. [Univ. of Pittsburgh, PA (United States); Klueh, R.L. [Oak Ridge National Lab., TN (United States)

1997-08-01

The microstructures of a 9Cr-2W-0.25-0.1C (9Cr-2WV), a 9Cr-2W-0.25V-0.07Ta-0.1C (9Cr-2WVTa), a 7Cr-2W-0.25V-0.07Ta-0.1C (7Cr-2WVTa), and a 5Cr-2W-0.25V-0.07Ta-0.1C (5Cr-2WVTa) steel (all compositions are in weight percent) have been characterized by Analytical Electron Microscopy (AEM) and Atom Probe Field Ion Microscopy (APFIM). The matrix in all four reduced-activation steels was 100% martensite. In the two 9Cr steels, the stable precipitates were blocky M{sub 23}C{sub 6} and small spherical MC. The two lower-chromium steels contained blocky M{sub 7}C{sub 3} and small needle-shaped carbonitrides in addition to M{sub 23}C{sub 6}. AEM and APFIM analysis revealed that in the steels containing tantalum, the majority of the tantalum was in solid solution. The experimental observations were in good agreement with phases and compositions predicted by phase equilibria calculations.

Experience manufacturing and properties of the high-strength corrosion-resistant magnetic 03Kh12K12D2 steel

International Nuclear Information System (INIS)

Fel'dgandler, Eh.G.; Moshkevich, E.I.; Bakuma, S.F.; Bulat, S.I.; Tikhonenko, V.D.

1976-01-01

In industrial conditions, steel 03Kh12K12D2 (DI48-VD) was melted in a 7-tinduction furnace with subsequent vacuum arc remelting. Ingots of dia 500 and 630 mm were forged into slabs and forgings. The slabs were rolled into sheets, 40 mm thick, and the forgings were rolled into sectional shapes. To obtain the optimum mechanical, corrosion, and magnetic properties, the metal was annealed at 600 deg C (10 hr) and 650 deg C (5 and 10 hr). The developed melting and remelting process enabled to obtain steel meeting all the requirements as for the chemical composition, workability, and mechanical magnetic properties. On testing in water with high parameters (200 deg C, 16 kgf/cm 2 ) and in synthetic sea water (70-90 deg C) the corrosion rate did not exceed 1 μm per year

Kankaan tuotekehittäminen erikoisolosuhteisiin K&H Annala Oy:lle

OpenAIRE

Koski, Marjo

2017-01-01

Opinnäytetyö tehtiin yhteistyössä Suomen ainoan huonekalukankaita valmistavan yrityksen K&H Annala Oy:n kanssa. Työn aiheena oli suunnitella ja tuotteistaa kangasmallisto erikoisolosuhteisiin innovatiivisesta, Italiassa valmistettavasta Flyer-langasta. Projektin lähtökohtana oli opinnäytetyöntekijän kasvava kiinnostuneisuus kudottuja tekstiilejä kohtaan ja kankaan suunnitteluprosessin vieminen teollisen tuotannon puolelle. Projektissa tähdättiin uudentyyppiseen kankaaseen ilmeen ja materiaali...

Study of effect of austenite prehistory of 03Ch20N16AG6 steel on it structure and properties

Energy Technology Data Exchange (ETDEWEB)

Demchuk, I S; Krakhmalev, V I; Manninen, A I [Leningradskij Politekhnicheskij Inst. (USSR)

1981-01-01

Effect of preliminary cold working and different procedures of thermal treatment on structure and mechanical properties of stable austenite of 03Kh20N16AG6 steel is found out. It is shown that the degree of defectability of initial austenite structure predetermines the further deformation behaviour of the steel (level of strength characteristics, plasticity storage, hardening degree etc.) in the wide temperature range. Close connection of structural changes with properties should determine the choice of preliminary treatment of stable austenitic steel as applied to concrete condition of operation.

Substitution of modified 9 Cr-1 Mo steel for austentic stainless steels

International Nuclear Information System (INIS)

Sikka, V.K.

1982-04-01

This report describes the current program to develop a high-strength ferritic-martensitic steel. The alloy is essentially Fe-9% Cr-1% Mo with small additions of V and Nb and is known as modifed 9 Cr-1 Mo steel. Its elevated-temperature properties and design allowable stresses match those of type 304 stainless steel for temperatures up to 600 0 C and exceed those of other ferritic steels by factors of 2 to 3. The improved strength of this alloy permits its use in place of stainless steels for many applications

Quality of structural steel melted by single-slag process

International Nuclear Information System (INIS)

Levin, A.M.; Andreev, V.I.; Monastyrskij, A.V.; Drozdova, M.F.; Pashchenko, V.E.; Orzhekh, M.B.

1982-01-01

The 40Kh and 12KhN3A steels were used to compare the quality of the metal manufactured according to several variants of a single-slag process with the metal of a conventional melting technology. Investigation results show, that a single-slag process metal has higher sulfides and oxides contents as well as an increased anisotropy of mechanical properties while its tendency to flake formation is weaker due to a less degree of gas saturation. It is marked that anisotropy in the properties and a sulfide content may be decreased by out-of-furnace treatment of steels

Properties of structural steels melted out of high-purity charge

International Nuclear Information System (INIS)

Marchenko, V.N.; Sergeeva, T.K.; Kondakova, N.K.; Morozov, V.P.; Madorskij, L.L.

1993-01-01

A comparative evaluation has been made of impurities, mechanical properties and hydrogen embirittlement parameters for steels type 40Kh and 40KhS produced by electrometallurgical method with the use of direct reduced charge (DR-steels) and melted in an open-hearth furnace. Investigation results have shown that 40Kh and 40KhS Dr-steels have more coarse austenitic grains and experience more complete transformation of martensite into ferritic-pearlitic mixture on tempering. Threshold stresses increase 2.5 times due to purity enhancement at the expense of application of direct reduced charge

Effect of hot rolling on the structure and the mechanical properties of nitrogen-bearing austenitic-martensitic 14Kh15AN4M steel

Science.gov (United States)

Bannykh, O. A.; Betsofen, S. Ya.; Lukin, E. I.; Blinov, V. M.; Voznesenskaya, N. M.; Tonysheva, O. A.; Blinov, E. V.

2016-04-01

The effect of the rolling temperature and strain on the structure and the properties of corrosionresistant austenitic-martensitic 14Kh15AN4M steel is studied. The steel is shown to exhibit high ductility: upon rolling in the temperature range 700-1100°C at a reduction per pass up to 80%, wedge steel specimens are uniformly deformed along and across the rolling direction without cracking and other surface defects. Subsequent cold treatment and low-temperature tempering ensure a high hardness of the steel (50-56 HRC). Austenite mainly contributes to the hardening upon rolling in the temperature range 700-800°C at a reduction of 50-70%, and martensite makes the main contribution at higher temperatures and lower strains. Texture does not form under the chosen deformation conditions, which indicates dynamic recrystallization with the nucleation and growth of grains having no preferential orientation.

Influence of cooling rates on the transformation behaviour of 9Cr-1Mo-0.07C steel

International Nuclear Information System (INIS)

Saroja, S.; Vijayalakshmi, M.; Raghunathan, V.S.

1992-01-01

The choice of various decomposition mechanisms of austenite in a 9Cr-1 Mo-0.07C steel under different rates of cooling has been studied. The techniques employed were electron probe micro-analysis, X-ray diffraction and electron microscopy. The observed morphological features may be explained based on the predominance of the two types of transformation, austenite → martensite and austenite → ferrite during cooling. In the steel used in this study, decomposition of austenite to proeutectoid ferrite was favoured at cooling rates less than about 2 Ks -1 . The mechanism by which the supersaturated proeutectoid ferrite relieves its excess solute concentration was also studied. A ''microstructural map'' has been proposed to predict the constitution at the end of any given cooling rate for 9Cr-1 Mo-0.07C steel. The choice of commercial treatment has been rationalized with respect to the resultant microstructural constituents. (Author)

Prognosis of 18 H7N9 avian influenza patients in Shanghai.

Directory of Open Access Journals (Sweden)

Shuihua Lu

Full Text Available To provide prognosis of an 18 patient cohort who were confirmed to have H7N9 lung infection in Shanghai.Patients' history, clinical manifestation, laboratory test, treatment strategy and mortality were followed and recorded for data analysis.A total of 18 patients had been admitted into Shanghai Public Health Clinical Center from April 8th to July 29, 2013. 22.2% of the patients were found to have live poultry contact history and 80% were aged male patients with multiple co-morbidities including diabetes, hypertension and/or chronic obstructive pulmonary disease (COPD. This group of patients was admitted to the clinical center around 10 days after disease onset. According to laboratory examinations, increased C reactive protein (CRP, Procalcitonin (PCT, Plasma thromboplastin antecedent (PTA and virus positive time (days were indicative of patients' mortality. After multivariate analysis, only CRP level showed significant prediction of mortality (P = 0.013 while results of prothrombin time (PT analysis almost reached statistical significance (P = 0.056.H7N9 infection induced pneumonia of different severity ranging from mild to severe pneumonia or acute lung injury/acute respiratory distress syndrome to multiple organ failure. Certain laboratory parameters such as plasma CRP, PCT, PTA and virus positive days predicted mortality of H7N9 infection and plasma CRP is an independent predictor of mortality in these patients.

Evaluation of the reliability of clinical staging of T2 N0 esophageal cancer: a review of the Society of Thoracic Surgeons database.

Science.gov (United States)

Crabtree, Traves D; Kosinski, Andrzej S; Puri, Varun; Burfeind, William; Bharat, Ankit; Patterson, G Alexander; Hofstetter, Wayne; Meyers, Bryan F

2013-08-01

Clinical staging of esophageal cancer has improved with positron-emission tomography/computed tomography and endoscopic ultrasound imaging. Despite such progress, small single-center studies have questioned the reliability of clinical staging of T2 N0 esophageal cancer. This study broadly examines the adequacy of clinical staging of T2 N0 disease using The Society of Thoracic Surgeons database. We retrospectively studied 810 clinical stage T2 N0 patients from 2002 to 2011, with 58 excluded because of incomplete pathologic staging data. Clinical stage, pathologic stage, and preoperative characteristics were recorded. Logistic regression analysis was used to identify factors associated with upstaging at the time of surgical intervention. Among 752 clinical stage T2 N0 patients, 270 (35.9%) received induction therapy before the operation. Of 482 patients who went directly to surgical intervention, 132 (27.4%) were confirmed as pathologic T2 N0, 125 (25.9%) were downstaged (ie, T0-1 N0), and 225 (46.7%) were upstaged at the operation (T3-4 N0 or Tany N1-3). Exclusive tumor upstaging (ie, pathologic T3-4 N0) accounted for 41 patients (18.2%), whereas exclusive nodal upstaging (ie, pathological T1-2 N1-3) accounted for 100 (44.5%). Combined tumor and nodal upstaging (ie, pathological T3-4 N1-3) accounted for 84 patients (37.3%). Among patients who received induction therapy, 103 (38.1%) were upstaged vs 225 (46.7%) without induction therapy (p = 0.026). Comparing the induction therapy group and the primary surgical group, postoperative 30-day mortality (3.7% vs 3.7%, p > 0.99) and morbidity (46.3% vs 45%, p = 0.76) were similar. Despite advances in staging techniques, clinical staging of T2 N0 esophageal cancer remains unreliable. Recognizing T2 N0 as a threshold for induction therapy in esophageal cancer, many surgeons have opted to treat T2 N0 disease with induction therapy, even though one-quarter of these patients will be pathologic T1 N0. Although this study

Influence of Nb content on grain size and mechanical properties of 18 wt% Cr ferritic stainless steel

Energy Technology Data Exchange (ETDEWEB)

Kang, Y. [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Mao, W.M., E-mail: weiminmao@263.net [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Chen, Y.J. [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Jing, J.; Cheng, M. [Taizhou Xinyu Precision Manufacture Company Limited, Jiangyan 225500, Jiangsu (China)

2016-11-20

The influence of Nb contents between 0.20 and 1.20 wt% on the grain size and mechanical properties of 18 wt% Cr ferritic stainless steel produced by investment casting was investigated. The average grain sizes of the three steels decreased apparently with increasing Nb content mainly due to the increasing number of pre-existing oxides formed at higher temperature, which were more likely to be the nuclei of heterogeneous nucleation. The thermodynamic analysis of Nb(C,N) formation was in conformity to the experimental result that the Nb(C,N) precipitates became larger with increasing Nb content. The as-cast specimen with the smallest grain size of steel C had the worse tensile strength and elongation in comparison with the as-cast specimens of steels A and B, mostly owing to the catenarian and dendritic Nb(C,N) particles distributed densely at the grain boundaries. The mechanical properties of specimens were not improved remarkably through high temperature solid-solution, whereas the mechanical properties of normalized specimens in the three steels were improved to different degrees. The coalescence and sparse distribution of smaller precipitates at grain boundaries after normalizing effectively weakened the local stress concentration arising from the reticular distribution of particles. The normalized specimen of steel A with 0.24 wt% Nb still showed good mechanical properties. Normalizing at 850 °C for 2 h is the appropriate heat treatment for the 18 wt% Cr ferritic stainless steel. The comparatively rational Nb content of the ferritic stainless steel is between 0.20 and 0.40 wt% for investment casting production.

Manufacture of tube billets for fuel cans by vacuum centrifugal casting

International Nuclear Information System (INIS)

Zelenskij, V.F.; Neklyudov, I.M.; Chernyj, B.P.

1989-01-01

Vacuum device for induction melting with centrifugal casting in the ingot mold with rotation vertical or horisontal axis is presented. Removing and grinding of nonmetallic inclusions are realized by selection of casting conditions and of chemically active reducer, sound metal with high ductility is obtained. Data on micro- and macrostructure of casted tube billets made of 08Kh18N10T and 06Kh16H15M3B stainless steels, designed for manufacture of fuel cans are presented

Behaviour of Z phase in 9–12%Cr steels

DEFF Research Database (Denmark)

Danielsen, Hilmar Kjartansson; Hald, John

2006-01-01

The literature on the behaviour of modified Z phase Cr(V,Nb)N in creep resistant martensitic 9–12%Cr steels is briefly reviewed. Ten different 9–12%Cr steels were investigated after prolonged exposure at 600–660uC; the modified Z phase was found in all of them. In steels with high Cr content (11......–12%), Z phase precipitates much faster than in 9%Cr steels. Precipitation of Z phase is associated with dissolution of MX carbonitrides, and causes a breakdown in long term creep strength in 9–12%Cr steels. High Cr steels show creep instabilities accompanied with Z phase precipitation, whereas low Cr...... steels show good long term creep stability. A niobium free CrVN variant of the modified Z phase was observed for the first time during the course of this work. The solution temperature of the Cr(V,Nb)N and CrVN modified Z phases was found to be close to 800uC for 11–12%Cr steels, much lower than the 1200...

Helium-induced weld degradation of HT-9 steel

International Nuclear Information System (INIS)

Wang, Chin-An; Chin, B.A.; Lin, Hua T.; Grossbeck, M.L.

1992-01-01

Helium-bearing Sandvik HT-9 ferritic steel was tested for weldability to simulate the welding of structural components of a fusion reactor after irradiation. Helium was introduced into HT-9 steel to 0.3 and 1 atomic parts per million (appm) by tritium doping and decay. Autogenous single pass full penetration welds were produced using the gas tungsten arc (GTA) welding process under laterally constrained conditions. Macroscopic examination showed no sign of any weld defect in HT-9 steel containing 0.3 appm helium. However, intergranular micro cracks were observed in the HAZ of HT-9 steel containing 1 appm helium. The microcracking was attributed to helium bubble growth at grain boundaries under the influence of high stresses and temperatures that were present during welding. Mechanical test results showed that both yield strength (YS) and ultimate tensile strength (UTS) decreased with increasing temperature, while the total elongation increased with increasing temperature for all control and helium-bearing HT-9 steels

Account of low temperature hardening in calculation of permissible stresses

International Nuclear Information System (INIS)

Novikov, N.V.; Ul'yanenko, A.P.; Gorodyskij, N.I.

1980-01-01

Suggested is a calculation scheme of permissible stresses with the account of temperature hardening for steels and alloys, the dependences of strength, plasticity and rupture work of which on cooling temperature do not have threshold changes in a wide range of low temperatures (from 300 to 4.2 K). Application of the suggested scheme is considered on the example of 12Kh18N10T austenitic chromium-nickel steel

Re-evaluation of Ipsilateral Radiation for T1-T2N0-N2b Tonsil Carcinoma at the Princess Margaret Hospital in the Human Papillomavirus Era, 25 Years Later

International Nuclear Information System (INIS)

Huang, Shao Hui; Waldron, John; Bratman, Scott V.; Su, Jie; Kim, John; Bayley, Andrew; Cho, John; Giuliani, Meredith; Hope, Andrew; Ringash, Jolie; Hansen, Aaron; Almeida, John R. de; Goldstein, David; Perez-Ordonez, Bayardo; Weinreb, Ilan; Tong, Li; Xu, Wei; O'Sullivan, Brian

2017-01-01

Purpose: To report the outcome of ipsilateral radiation therapy (RT) in human papillomavirus (HPV)-positive (HPV+) patients and HPV-negative (HPV−) patients with T1-T2N0-N2b tonsillar cancer treated 25 years after our initial historical cohort. Methods and Materials: Patients with T1-T2N0-N2b tonsillar cancer who received ipsilateral RT or bilateral RT between 1999 and 2014 were reviewed. Overall survival (OS), local control (LC), regional control (RC), and grade 3 to 4 late toxicity (LT) were compared between ipsilateral RT and bilateral RT within HPV+ and HPV− patients, separately. Results: HPV status was ascertained in 379/427 (88%) consecutive patients (ipsilateral RT: 62 HPV+, 34 HPV−; bilateral RT: 240 HPV+ 240, 41 HPV−). The proportion of ipsilateral RT by N category for HPV+ and HPV− patients were as follows: N0: 24/37 (65%) versus 28/48 (74%); N1: 21/49 (43%) versus 4/9 (44%); N2a: 10/39 (26%) versus 1/4 (25%); and N2b: 7/177 (4%) versus 1/24 (4%), respectively. Of the patients receiving ipsilateral RT, 94/96 (98%) were treated with RT alone. The median follow-up time was 5.03 years. The respective 5-year rates of OS, LC, RC, and LT were similar between ipsilateral RT and bilateral RT for the HPV+ patients (OS: 89% vs 87%, P=.55; LC: 97% vs 98%, P=.65; RC: 98% vs 97%, P=.27; LT: 17% vs 12%, P=.83) and HPV− patients (OS: 63% vs 48%, P=.27; LC: 90% vs 80%, P=.19; RC: 94% vs 83%, P=.14; LT: 15% vs 22%, P=.36). Of the 96 patients receiving ipsilateral RT, contralateral neck failure (CNF) occurred in 1/52 HPV+ patients and 1/34 HPV− patients. The 5-year CNF rates were 2% (95% CI: 1-9) (HPV+: 2% [0-14]; HPV−: 3% [0-21], P=.66). Five local failures (2 HPV+; 3 HPV−) and no distant failures were seen. The 5-year rates of LC, RC, and LT were 97% versus 90% (P=.24), 98% versus 94% (P=.25), and 18% versus 15% (P=.75) for the HPV+ and HPV− cohorts, respectively. Osteoradionecrosis occurred in 9 patients: 6/47 (13%) treated with conventional RT

Re-evaluation of Ipsilateral Radiation for T1-T2N0-N2b Tonsil Carcinoma at the Princess Margaret Hospital in the Human Papillomavirus Era, 25 Years Later

Energy Technology Data Exchange (ETDEWEB)

Huang, Shao Hui, E-mail: shaohui.huang@rmp.uhn.on.ca [Department of Radiation Oncology, The Princess Margaret Cancer Centre, University of Toronto, Toronto, Ontario (Canada); Waldron, John [Department of Radiation Oncology, The Princess Margaret Cancer Centre, University of Toronto, Toronto, Ontario (Canada); Department of Otolaryngology—Head & Neck Surgery, The Princess Margaret Cancer Centre, University of Toronto, Toronto, Ontario (Canada); Bratman, Scott V. [Department of Radiation Oncology, The Princess Margaret Cancer Centre, University of Toronto, Toronto, Ontario (Canada); Su, Jie [Department of Biostatistics, The Princess Margaret Cancer Centre, University of Toronto, Toronto, Ontario (Canada); Kim, John; Bayley, Andrew; Cho, John; Giuliani, Meredith; Hope, Andrew; Ringash, Jolie [Department of Radiation Oncology, The Princess Margaret Cancer Centre, University of Toronto, Toronto, Ontario (Canada); Hansen, Aaron [Division of Medical Oncology, The Princess Margaret Cancer Centre, University of Toronto, Toronto, Ontario (Canada); Almeida, John R. de; Goldstein, David [Department of Otolaryngology—Head & Neck Surgery, The Princess Margaret Cancer Centre, University of Toronto, Toronto, Ontario (Canada); Perez-Ordonez, Bayardo; Weinreb, Ilan [Department of Pathology, The Princess Margaret Cancer Centre, University of Toronto, Toronto, Ontario (Canada); Tong, Li [Department of Radiation Oncology, The Princess Margaret Cancer Centre, University of Toronto, Toronto, Ontario (Canada); Xu, Wei [Department of Biostatistics, The Princess Margaret Cancer Centre, University of Toronto, Toronto, Ontario (Canada); O' Sullivan, Brian [Department of Radiation Oncology, The Princess Margaret Cancer Centre, University of Toronto, Toronto, Ontario (Canada); Department of Otolaryngology—Head & Neck Surgery, The Princess Margaret Cancer Centre, University of Toronto, Toronto, Ontario (Canada)

2017-05-01

Purpose: To report the outcome of ipsilateral radiation therapy (RT) in human papillomavirus (HPV)-positive (HPV+) patients and HPV-negative (HPV−) patients with T1-T2N0-N2b tonsillar cancer treated 25 years after our initial historical cohort. Methods and Materials: Patients with T1-T2N0-N2b tonsillar cancer who received ipsilateral RT or bilateral RT between 1999 and 2014 were reviewed. Overall survival (OS), local control (LC), regional control (RC), and grade 3 to 4 late toxicity (LT) were compared between ipsilateral RT and bilateral RT within HPV+ and HPV− patients, separately. Results: HPV status was ascertained in 379/427 (88%) consecutive patients (ipsilateral RT: 62 HPV+, 34 HPV−; bilateral RT: 240 HPV+ 240, 41 HPV−). The proportion of ipsilateral RT by N category for HPV+ and HPV− patients were as follows: N0: 24/37 (65%) versus 28/48 (74%); N1: 21/49 (43%) versus 4/9 (44%); N2a: 10/39 (26%) versus 1/4 (25%); and N2b: 7/177 (4%) versus 1/24 (4%), respectively. Of the patients receiving ipsilateral RT, 94/96 (98%) were treated with RT alone. The median follow-up time was 5.03 years. The respective 5-year rates of OS, LC, RC, and LT were similar between ipsilateral RT and bilateral RT for the HPV+ patients (OS: 89% vs 87%, P=.55; LC: 97% vs 98%, P=.65; RC: 98% vs 97%, P=.27; LT: 17% vs 12%, P=.83) and HPV− patients (OS: 63% vs 48%, P=.27; LC: 90% vs 80%, P=.19; RC: 94% vs 83%, P=.14; LT: 15% vs 22%, P=.36). Of the 96 patients receiving ipsilateral RT, contralateral neck failure (CNF) occurred in 1/52 HPV+ patients and 1/34 HPV− patients. The 5-year CNF rates were 2% (95% CI: 1-9) (HPV+: 2% [0-14]; HPV−: 3% [0-21], P=.66). Five local failures (2 HPV+; 3 HPV−) and no distant failures were seen. The 5-year rates of LC, RC, and LT were 97% versus 90% (P=.24), 98% versus 94% (P=.25), and 18% versus 15% (P=.75) for the HPV+ and HPV− cohorts, respectively. Osteoradionecrosis occurred in 9 patients: 6/47 (13%) treated with conventional RT

Is Biological Subtype Prognostic of Locoregional Recurrence Risk in Women With pT1-2N0 Breast Cancer Treated With Mastectomy?

International Nuclear Information System (INIS)

Truong, Pauline T.; Sadek, Betro T.; Lesperance, Maria F.; Alexander, Cheryl S.; Shenouda, Mina; Raad, Rita Abi; Taghian, Alphonse G.

2014-01-01

Purpose: To examine locoregional and distant recurrence (LRR and DR) in women with pT1-2N0 breast cancer according to approximated subtype and clinicopathologic characteristics. Methods and Materials: Two independent datasets were pooled and analyzed. The study participants were 1994 patients with pT1-2N0M0 breast cancer, treated with mastectomy without radiation therapy. The patients were classified into 1 of 5 subtypes: luminal A (ER+ or PR+/HER 2−/grade 1-2, n=1202); luminal B (ER+ or PR+/HER 2−/grade 3, n=294); luminal HER 2 (ER+ or PR+/HER 2+, n=221); HER 2 (ER−/PR−/HER 2+, n=105) and triple-negative breast cancer (TNBC) (ER−/PR−/HER 2−, n=172). Results: The median follow-up time was 4.3 years. The 5-year Kaplan-Meier (KM) LRR were 1.8% in luminal A, 3.1% in luminal B, 1.7% in luminal HER 2, 1.9% in HER 2, and 1.9% in TNBC cohorts (P=.81). The 5-year KM DR was highest among women with TNBC: 1.8% in luminal A, 5.0% in luminal B, 2.4% in luminal HER 2, 1.1% in HER 2, and 9.6% in TNBC cohorts (P 2 cm, lobular histology, and close/positive surgical margins. Conclusions: The 5-year risk of LRR in our pT1-2N0 cohort treated with mastectomy was generally low, with no significant differences observed between approximated subtypes. Among the subtypes, TNBC conferred the highest risk of DR and an elevated risk of LRR in the presence of positive or close margins. Our data suggest that although subtype alone cannot be used as the sole criterion to offer postmastectomy radiation therapy, it may reasonably be considered in conjunction with other clinicopathologic factors including tumor size, histology, and margin status. Larger cohorts and longer follow-up times are needed to define which women with node-negative disease have high postmastectomy LRR risks in contemporary practice

Cooling intensification during quenching of power plant components - the way to increase reliability

International Nuclear Information System (INIS)

Borisov, I.A.

1989-01-01

To enchance the complex of mechanical properties and to increase operation time of large components of power facilities, regimes of accelerated cooling are developed. Results of heat treatment with accelerated cooling of turbine rotor of steel 26KhN3M2FAA, disks of turbine welded rotor of steel 20KhN2MFAA, components of steel 35KhN3MFA, are given. Special steels with carbon content less than 0.30% for details of power machine-building are developed

Microhardness of boron, titanium, and nitrogen implanted steel

International Nuclear Information System (INIS)

Sowa, M.; Szyszko, W.; Sielanko, J.; Glusiec, L.

1989-01-01

Mechanically polished steel (1H18N9T) and (15GTM) samples are implanted with boron, titanium, and nitrogen ions, with dose ranging from 10 16 to 10 17 ions/cm 2 . The implantation energy varied from 100 to 250 keV. Implanted samples are heat-treated at 400 to 800 0 C in vacuum. The microhardness of implanted samples is measured by using a Hanneman tester with loads ranging from 2 to 40 g. The influence of annealing temperature on microhardness of the implanted layers is determined. The diffusion of boron from the implanted layers is also investigated by using the secondary ion mass spectrometer. The diffusion coefficients of boron in steel are determined. (author)

Influence of PECVD deposited SiNx passivation layer thickness on In0.18Al0.82N/GaN/Si HEMT

International Nuclear Information System (INIS)

Singh, Sarab Preet; Liu, Yi; Ngoo, Yi Jie; Kyaw, Lwin Min; Bera, Milan Kumar; Chor, Eng Fong; Dolmanan, S B; Tripathy, Sudhiranjan

2015-01-01

The influence of plasma enhanced chemical vapour deposited (PECVD) silicon nitride (SiN x ) passivation film thickness on In 0.18 Al 0.82 N/GaN/Si heterostructures and HEMTs has been investigated. The formation of Si 3 N 4 was confirmed by x-ray photoelectron spectroscopy (XPS) measurements. X-ray reflectivity (XRR) measurements reveal that both the density and roughness of the SiN x film increase with increasing film thickness. With an increase in SiN x film thickness, a significant increase in two-dimensional electron gas (2DEG) density, drain current, extrinsic transconductance and negative threshold voltage shift of the In 0.18 Al 0.82 /GaN/Si HEMTs are observed. An optimal thickness of SiN x is ∼100 nm and it yields a substantial increase in 2DEG density (∼30%) with a minimum sheet resistance for In 0.18 Al 0.82 N/GaN/Si heterostructures. Furthermore, we correlate the observed SiN x film thickness-dependent electrical characteristics of In 0.18 Al 0.82 /GaN/Si HEMTs with the density of the SiN x film. (paper)

On superplasticity of corrosion resistant ferritic-austenitic chromium-nickel steels

Energy Technology Data Exchange (ETDEWEB)

Surovtsev, A P; Sukhanov, V E

1988-01-01

The deformability of corrosion resistant chromium-nickel ferritic austenitic steel type O8Kh22N6T under tension, upsetting and torsion in the 600-1200 deg C temperature range is studied. For the deformation rate of the order of 10/sup -3/ s/sup -1/ the effect of superelasticity reveals itself at 850 deg C in the process of ferrite dynamic polymerization, in the 925-950 deg C range, at initial stages of dynamic recrystallization - the dynamic polygonization controlled by chromium carbide dissolving in steel and maximum at 1050 deg C in the process of development of austenite dynamic recrystallization with grain refinement with F/A ratio equalling 1. After upsetting in the elasticity mode at 1050 deg C the impact strength of the above steel is maximum.

Enhancement of tribological properties of 9Cr18 stainless steel by dual Mo and S Co implantation

International Nuclear Information System (INIS)

Zhang Tao; Song Jiaohua; Li Guoqing; Chu, Paul K.; Brown, Ian G.

2001-01-01

Mo and S ions were simultaneously implanted into 9Cr18 stainless steel samples. The frictional properties of the implanted samples were assessed using a pin-on-disk tester and the elemental depth profiles were measured by Auger electron spectroscopy. The hardness of the samples was also measured. We find that this dual-element implantation process reduces the coefficient of friction by a factor of 2 and increases the low-friction lifetime by a factor of 4 compared to the 9Cr18 surface with Mo or S implantation alone. This enhancement is related to the synergistic coexistence of the implanted elements at the same place. We have also investigated the process using computer simulation. The simulation results help disclose the characteristics of the modified layer and explain the effects of dual-element ion implantation

Elevated Temperature Corrosion Studies of AlCrN and TiAlN Coatings by PAPVD on T91 Boiler Steel

Science.gov (United States)

Goyal, Lucky; Chawla, Vikas; Hundal, Jasbir Singh

2017-11-01

The present investigation discusses the hot corrosion behavior of AlCrN and TiAlN nano-coatings on T91 boiler steel by PAPVD process subjected to molten salt of Na2SO4-60%V2O5 at 900 °C for 50 cycles. Surface and cross-sectional studies were performed by AFM, SEM/EDS and XRD techniques to understand the corrosion kinetics and mechanism. T91 bare boiler steel as well as TiAlN-coated specimen has shown higher internal oxidation as well as weight gain. The better corrosion resistance of AlCrN-coated specimen has been observed by virtue of higher availability of Cr and Al in the oxide scale as well as adherent and dense coating. The betterment of AlCrN coating can be attributed to low internal oxidation as well as movement of Cr and Al toward oxide scale to form protective corrosion barriers.

On the low-cycle fracture of chromium-nickel-molybdenum structural steels in seawater

International Nuclear Information System (INIS)

Karpenko, G.V.; Kobzaruk, A.V.; Malyshevskij, V.A.; Shul'te, A.Yu.; Rybin, V.V.; Silaev, I.I.

1977-01-01

The processes of low-cycle fracture of the chrome-nickel-molybdenum steels 15KhN5MF, 12KhN4MF and 15KhN3M in air, and in sea water have been investigated by the optical microscopy method, and electron microscopic examination of thin films. Bringing no change in the fracture character, sea water produces a speeding-up effect on the low-cycle fatigue fracture process. During long-time corrosion fatigue testing considerable importance lies with the electrochemical corrosion factor expediting the occurrence of corrosive pits acting as crack-initiation nuclei, fatigue crack attack, accumulation of corrosion products in fatigue cracks, etc

Analysis of nature of brazed joints fracture under operating conditions

International Nuclear Information System (INIS)

Orlov, A.V.; Gura, P.M.

1985-01-01

Technique establishing causes leading to brazed joint fracture in pressure boundary components, operating under heavy conditions of high temperature and corrosive medium is described. Some cases of tube brazed joint fractures in a superheater of 12Kh1MF and 08Kh18N10T steels are considered. The attention is paid on using metallography for determination of mechanical or corrosion fracture properties. The diagram is developed permitting to take into account the interrelation between the fracture area in the given zone and its strength

Numerical simulation on temperature field of TIG welding for 0Cr18Ni10Ti steel cladding and experimental verification

International Nuclear Information System (INIS)

Luo Hongyi; Tang Xian; Luo Zhifu

2015-01-01

Aiming at tungsten inert gas (TIG) for 0Cr18Ni10Ti stainless steel cladding for radioactive source, the numerical calculation of welding pool temperature field was carried out through adopting ANSYS software. The numerical model of non-steady TIG welding pool shape was established, the heat enthalpy and Gaussian electric arc heat source model of surface distribution were introduced, and the effects of welding current and welding speed to temperature field distribution were calculated. Comparing the experimental data and the calculation results under different welding currents and speeds, the reliability and correctness of the model were proved. The welding technological parameters of 0Cr18Ni10Ti stainless steel were optimized based on the calculation results and the welding procedure was established. (authors)

Reliability and durability of the 12Kh1MF steel tubes of electroslag remelting and their welded joints

International Nuclear Information System (INIS)

Lanskaya, K.A.; Kulikova, L.V.; Mazel', R.E.; Khromchenko, F.A.; Strizhenova, V.F.

1978-01-01

Results of investigating the positive effect of electrolag remelting (ESR) on the properties of the base metal and welded joint of the 12Kh1MF steel steam pipes with the aim of increasing their durability up to 20,000 hrs, are presented. To estimate the quality and properties of tube billet metal, microstructure, content and nature of nonmetallic inclusions, content of gases, austenite grain size, austenite transformations during continuous cooling, metal ductility, mechanical properties at different temperatures and heat resisting properties, have been investigated. It is established, that the base metal in tubes of electroslag remelting possess higher heat resistance, while welded joints besides, have high deformability and resistance to brittle fracture

Annealing dislocation loops in OKh16N15M3T steel implanted by helium

International Nuclear Information System (INIS)

Utkelbaev, B.D.; Reutov, V.F.; Zhdan, G.T.

1993-01-01

With the use of electron microscopy a study was made into the influence of preliminary thermomechanical treatment on the process of dislocation loop development in austenitic stainless steel type OKh16N15M3T with helium on annealing. Preliminary treatment was shown to prevent dislocation loop formation to a greater or lesser extent. Preliminary 'cold' working and thermal ageing of the material are the most effective ways to suppress radiation defect formation when annealing helium implanted steel

Methodic recommendations on ultrasonic testing of pipeline austenitic butt joints

International Nuclear Information System (INIS)

Grebennik, V.S.; Lantukh, V.M.; Tajts, M.Z.; Ermolov, I.N.; Volkov, A.S.; Vyatskov, I.A.; Kesler, N.A.; Shchedrin, I.F.

1989-01-01

Recommendations for the application of ultrasonic testing of austenitic welded joints of the Du 500 pipelines with the walls 32-34 mm thick made of steel Kh18N10T are developed. The optimal values of the main parameters of ultrasonic testing are determined experimentally. Principles of calculation of the optimal parameters are considered. 1 ref.; 4 figs

Creep deformation and rupture behaviour of 9Cr–1W–0.2V–0.06Ta Reduced Activation Ferritic–Martensitic steel

International Nuclear Information System (INIS)

Vanaja, J.; Laha, K.; Mythili, R.; Chandravathi, K.S.; Saroja, S.; Mathew, M.D.

2012-01-01

Highlights: ► Creep tests on broad temperature and stress ranges were carried out. ► Microstructural instability on creep and thermal exposures were studied using TEM. ► Creep damage tolerance factor of the material was estimated. - Abstract: This paper presents the creep deformation and rupture behaviour of indigenously produced 9Cr–1W–0.2V–0.06Ta Reduced Activation Ferritic–Martensitic (RAFM) steel for fusion reactor application. Creep studies were carried out at 773, 823 and 873 K over a stress range of 100–300 MPa. The creep deformation of the steel was found to proceed with relatively shorter primary regime followed by an extended tertiary regime with virtually no secondary regime. The variation of minimum creep rate of the material with applied stress followed a power law relation, ε m = Aσ n , with stress exponent value ‘n’ decreasing with increase in temperature. The product of minimum creep rate and creep rupture life was found to obey the modified Monkman–Grant relation. The time to onset of tertiary stage of deformation was directly proportional to rupture life. TEM studies revealed relatively large changes in martensitic sub-structure and coarsening of precipitates in the steel on creep exposure as compared to thermal exposure. Microstructural degradation was considered as the prime cause of extended tertiary stage of creep deformation, which was also reflected in the damage tolerance factor λ with a value more than 2.5. In view of the microstructural instability of the material on creep exposure, the variation of minimum creep rate with stress and temperature did not obey Dorn's equation modified by invoking Lagneborg and Bergman's concepts of back stress.

[Evaluation of central lymph node dissection for papillary thyroid carcinoma in cN0 T1/T2].

Science.gov (United States)

Zhao, S Y; Ma, Y H; Yin, Z; Zhan, X X; Cheng, R C; Qian, J

2018-02-07

Objective: To evaluate the application of the central lymph node dissection (CLND) for papillary thyroid carcinoma (PTC) in cN0 T1/T2. Methods: Retrospective analysis of 532 cases with PTC in cN0 T1/T2 who underwent CLND between October 2014 and September 2016 in the Department of Thyroid Surgery, the First Affiliated Hospital of the Kunming Medical University. The incidence of central lymph node (CLN) metastasis and risk factors were analyzed. Results: CLN metastasis rates: 41.2% (42/102) in males vs 34.9% (150/430) in females, P =0.252; 33.9% (116/342) in single focal carcinoma vs 40.4% (74/183) in multifocal carcinoma, P =0.157; 44.0% (125/284) in patients with 45 years old or less vs 27.0% (67/248) in patients more than 45 years old, P =0.000; 30.3% (113/373) in microcarcinoma vs 50.9% (81/159) in non-microcarcinoma, P =0.000.In unilateral lesions, ipsilateral CLN metastasis was correlated with the tumor diameter ( P =0.012), but not with the number of lesions ( P =0.653). also contralateral CLN metastasis was correlated with the tumor diameter ( P =0.000), but not with the number of lesions ( P =0.815). For the left or right unilateral single focal lesion, the tumor diameter was not correlated with the metastasis of the posterior to right recurrent laryngeal nerve central lymph nodes (LN-prRLN-CLN) ( P =0.652, P =0.088). But in bilateral multifocal carcinoma the tumor diameter was correlated with metastasis of LN-prRLN-CLN ( P =0.039). Conclusions: Prophylactic CLND is reasonable for PTC in cN0 T1/T2. A bilateral CLND should be conducted for patients with bilateral multi-focus cancer and unilateral or bilateral non-microcarcinoma, especially in patients more than 45 years old. For unilateral single focal microcarcinoma on the right, the content of CLND should be from laryngeal nerve on right center to posterior branche; for unilateral single focal microcarcinoma on the left side, the left CLND should be conducted. An ipsilateral CLND can be considered in

Is Biological Subtype Prognostic of Locoregional Recurrence Risk in Women With pT1-2N0 Breast Cancer Treated With Mastectomy?

Energy Technology Data Exchange (ETDEWEB)

Truong, Pauline T., E-mail: ptruong@bccancer.bc.ca [Radiation Therapy Program, British Columbia Cancer Agency, Vancouver Island Centre, University of British Columbia, Victoria, BC (Canada); Breast Cancer Outcomes Unit, British Columbia Cancer Agency, Vancouver Island Centre, University of British Columbia, Victoria, BC (Canada); Sadek, Betro T. [Department of Radiation Oncology, Massachusetts General Hospital, Harvard Medical School, Boston, Massachusetts (United States); Lesperance, Maria F. [Radiation Therapy Program, British Columbia Cancer Agency, Vancouver Island Centre, University of British Columbia, Victoria, BC (Canada); Alexander, Cheryl S. [Breast Cancer Outcomes Unit, British Columbia Cancer Agency, Vancouver Island Centre, University of British Columbia, Victoria, BC (Canada); Shenouda, Mina; Raad, Rita Abi; Taghian, Alphonse G. [Department of Radiation Oncology, Massachusetts General Hospital, Harvard Medical School, Boston, Massachusetts (United States)

2014-01-01

Purpose: To examine locoregional and distant recurrence (LRR and DR) in women with pT1-2N0 breast cancer according to approximated subtype and clinicopathologic characteristics. Methods and Materials: Two independent datasets were pooled and analyzed. The study participants were 1994 patients with pT1-2N0M0 breast cancer, treated with mastectomy without radiation therapy. The patients were classified into 1 of 5 subtypes: luminal A (ER+ or PR+/HER 2−/grade 1-2, n=1202); luminal B (ER+ or PR+/HER 2−/grade 3, n=294); luminal HER 2 (ER+ or PR+/HER 2+, n=221); HER 2 (ER−/PR−/HER 2+, n=105) and triple-negative breast cancer (TNBC) (ER−/PR−/HER 2−, n=172). Results: The median follow-up time was 4.3 years. The 5-year Kaplan-Meier (KM) LRR were 1.8% in luminal A, 3.1% in luminal B, 1.7% in luminal HER 2, 1.9% in HER 2, and 1.9% in TNBC cohorts (P=.81). The 5-year KM DR was highest among women with TNBC: 1.8% in luminal A, 5.0% in luminal B, 2.4% in luminal HER 2, 1.1% in HER 2, and 9.6% in TNBC cohorts (P<.001). Among 172 women with TNBC, the 5-year KM LRR were 1.3% with clear margins versus 12.5% with close or positive margins (P=.04). On multivariable analysis, factors that conferred higher LRR risk were tumors >2 cm, lobular histology, and close/positive surgical margins. Conclusions: The 5-year risk of LRR in our pT1-2N0 cohort treated with mastectomy was generally low, with no significant differences observed between approximated subtypes. Among the subtypes, TNBC conferred the highest risk of DR and an elevated risk of LRR in the presence of positive or close margins. Our data suggest that although subtype alone cannot be used as the sole criterion to offer postmastectomy radiation therapy, it may reasonably be considered in conjunction with other clinicopathologic factors including tumor size, histology, and margin status. Larger cohorts and longer follow-up times are needed to define which women with node-negative disease have high postmastectomy LRR

Fatigue Resistance of GX12CrMoVNbN9-1 Cast Steel after Ageing Process

Directory of Open Access Journals (Sweden)

Stanisław MROZIŃSKI

2014-12-01

Full Text Available In the present paper, low cycle fatigue behaviour of GX12CrMoVNbN9-1 (GP91 cast steel is presented. Fatigue tests were performed under isothermal conditions at room temperature and at 550 and 600oC, on five levels of total strain amplitude value ɛac = 0.25÷0.60%. The cast steel subject to investigation was in the as-received condition (after heat treatment and after 8000 hours of ageing at the temperature of 600oC. Performed research has shown an insignificant influence of the ageing process on mechanical properties of GP91 cast steel, determined with the static test of tension. Analysis of the performed tests has proved that GP91 cast steel in the as-received condition and after ageing process was characterized by strong cyclic softening without a clear period of stabilization of the hysteresis loop parameters. The fatigue lifetime curves at each temperature were obtained based on Basquin and Coffin – Manson equations. The process of ageing of GP91 cast steel contributed to a decrease in its fatigue life Nf from a few to a few dozen percent, and the level of fatigue life was dependent on the value of strain amplitude ɛac. It has also been stated that the fatigue life Nf of GP91 cast steel is determined by its plastic properties, and the degree of changes in fatigue life Nf was dependent not only on the temperature of testing, but also on the value of strain amplitude ɛac. DOI: http://dx.doi.org/10.5755/j01.ms.20.4.6077

Survival of T4aN0 and T3N+ laryngeal cancer patients: a retrospective institutional study and systematic review.

Science.gov (United States)

Khoueir, Nadim; Matar, Nayla; Farah, Chadi; Francis, Evana; Tabchy, Bassam; Haddad, Amine

2015-01-01

We aim to assess the correlation of tumor and nodal staging to survival in pT3N+ and T4aN0 laryngeal cancer with subgroup analysis within stage IVa (pT4N0 and pT3N2). Retrospective cohort study with systematic review of the literature. Hotel Dieu de France University Hospital (tertiary referral center). Laryngeal cancer patients' registries were reviewed from 1998 to 2012 selecting pT3N+ and pT4aN0 patients treated by primary total layngectomy. Overall survivals were compared using Log rank and Kaplan-Meier analysis. A systematic review was performed by 2 reviewers including all the articles reporting the outcome of these categories of patients. Online databases, including PubMed and EMBASE, were used. Reference sections of identified studies were examined for additional articles. Thirteen T3N+ patients and 19 T4aN0 patients treated by primary total laryngectomy were included. Five-year overall survival for T3N+, T3N2 and T4aN0 was respectively 33%, 32.1% and 73.7%. Due to the small sample, the difference was not significant. The systematic review revealed three articles reporting overall survival outcome for the T4N0 group and 6 articles for the T3N+. At 5years, the survival ranged from 62.5% to 73% in T4N0 and from 32.2% to 77% in T3N+. In advanced stage laryngeal cancer, T4aN0 tends toward a better survival than T3N+ especially when compared to T3N2 although they are grouped in the same TNM stage IVa. Copyright © 2015 Elsevier Inc. All rights reserved.

Microstructural evolution of nanostructured Ti0.9Al0.1N prepared by reactive ball-milling

International Nuclear Information System (INIS)

Bhaskar, U.K.; Bid, S.; Pradhan, S.K.

2011-01-01

Research highlights: → Nanocrystalline stoichiometric Ti 0.9 Al 0.1 N powder has been prepared by ball-milling the 0.9 mol fraction of α-Ti (hcp) and 0.1 mol fraction of aluminum (fcc) powders under N 2 at room temperature. Initially, α-Ti phase partially transformed to the transient β-Ti phase and Ti 0.9 Al 0.1 N (fcc) phase is noticed to form after 3 h of milling. Nanocrystalline stoichiometric Ti 0.9 Al 0.1 N phase is formed after 7 h of milling. The main features which are observed in the present study are stated below: 1.During ball-milling of α-Ti, the α-Ti phase partially converted to transient cubic β-Ti phase within 1 h of milling. 2.Ti 0.9 Al 0.1 N (fcc) phase is noticed to form after 3 h of milling. Complete formation of Ti 0.9 Al 0.1 N (fcc) is obtained at 7 h of milling which is lesser than complete formation time (9 h) of TiN. Doping Al atoms accelerates the formation of (TiAl)N phase. 3.The particle size of Ti 0.9 Al 0.1 N decrease rapidly up to 3 h and then increase slightly due to agglomeration effect. 4.The particle size of Ti 0.9 Al 0.1 N estimated from X-ray is in good agreement with that measured from HRTEM. - Abstract: Nanocrystalline stoichiometric Ti 0.9 Al 0.1 N powder has been prepared by ball-milling the α-Ti (hcp) and aluminum (fcc) powders under N 2 at room temperature. Initially, α-Ti phase partially transformed to the transient cubic β-Ti phase and Ti 0.9 Al 0.1 N (fcc) phase is noticed to form after 3 h of milling. Nanocrystalline stoichiometric Ti 0.9 Al 0.1 N phase is formed after 7 h of milling. After 1 h of milling, all Al atoms are diffused into the α-Ti matrix. The transient β-Ti phase is noticed to form after 1 h of milling and disappears completely after 7 h of milling. Microstructure characterization of unmilled and ball-milled powders by analyzing XRD patterns employing the Rietveld structure refinement reveals the inclusion of Al and nitrogen atoms into the Ti lattice on the way to formation of Ti 0.9 Al 0.1 N

Investigation into mechanical properties of joints of heterogeneous materials brazed with high-temperature solders

International Nuclear Information System (INIS)

Lomenko, V.I.; Merkushev, V.P.; Borodina, L.M.; Sycheva, T.S.; Tokhtina, O.A.; Frolov, N.N.

1988-01-01

Mechanical properties of copper joints with copper, 12Kh18M10T steel and KhD50 composite obtained by vacuum brazing by copper-titanium solder as compared with properties of joints brazed by PSr 72 and PMFOTsr 6-4-0.03 solders in hydrogen are studied. Dependences of joints strength on temperature of contact - reactive vacuum brazing are obtained. Possible applications of joints of dissimilar materials in electrovacuum devices subjected to the effect of dynamic loadings are established

Effect of neutron irradiation on the properties of the repair welds of the 15Kh2MFA steel

International Nuclear Information System (INIS)

Morozov, A.M.; Khachaturyants, L.V.

1986-01-01

The authors studied the effect of neutron irradiation on the tendency of the metal belonging to the heat affected zone of the weld toward brittle fracture (an increase in the critical temperature of brittleness). For comparison, the authors studied the radiation embrittlement of the original base metal (steel 15Kh2MFA) subjected to the conventional heat treatment of the reactor frames consisting of hardening and high-temperature tempering. Along with these materials, the radiational embrittlement of the base metal in the rehardened condition without tempering was studied. It was concluded that the presence of the regions repaired according to this technology and located in the frame at the level of the reactor core does not pose the problem of decreased resistance to brittle fracture

Influence of the channel electric field distribution on the polarization Coulomb field scattering in In0.18Al0.82N/AlN/GaN heterostructure field-effect transistors

International Nuclear Information System (INIS)

Yu Ying-Xia; Lin Zhao-Jun; Luan Chong-Biao; Yang Ming; Wang Yu-Tang; Lü Yuan-Jie; Feng Zhi-Hong

2014-01-01

By making use of the quasi-two-dimensional (quasi-2D) model, the current–voltage (I–V) characteristics of In 0.18 Al 0.82 N/AlN/GaN heterostructure field-effect transistors (HFETs) with different gate lengths are simulated based on the measured capacitance–voltage (C–V) characteristics and I–V characteristics. By analyzing the variation of the electron mobility for the two-dimensional electron gas (2DEG) with electric field, it is found that the different polarization charge distributions generated by the different channel electric field distributions can result in different polarization Coulomb field scatterings. The difference between the electron mobilities primarily caused by the polarization Coulomb field scatterings can reach up to 1522.9 cm 2 /V·s for the prepared In 0.18 Al 0.82 N/AlN/GaN HFETs. In addition, when the 2DEG sheet density is modulated by the drain–source bias, the electron mobility presents a peak with the variation of the 2DEG sheet density, the gate length is smaller, and the 2DEG sheet density corresponding to the peak point is higher. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

Effect of the radiation in the reference temperature T{sub 0} in ferritic steel; Efecto de la radiacion en la temperatura de referencia T{sub 0} en acero ferritico

Energy Technology Data Exchange (ETDEWEB)

Villanueva O, A.; Gachuz M, M.E. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

2004-07-01

The present work studies the effect that produces the irradiation in ferritic steels (AISI 8620) on the reference temperature (T{sub 0}) that characterizes the tenacity to the fractures (K{sub JC}) of these materials obtaining this way a characteristic curve (Master Curve) of this steel. The approach of the 'Master curve' is based on the Astm E-1921. Following this standard the methodology of a sub size settled down in Charpy type test tubes. Due to this type of steels is used mainly in pressure vessels of the reactor in Nuclear Power plants, the fracture tenacity gives the rule at the moment for the verification of structural integrity of the pressure vessel of the reactor. (Author)

Effects of Intercritical Annealing Temperature on Mechanical Properties of Fe-7.9Mn-0.14Si-0.05Al-0.07C Steel

Directory of Open Access Journals (Sweden)

Xianming Zhao

2014-12-01

Full Text Available A medium Mn steel has been designed to achieve an excellent combination of strength and ductility based on the TRIP (Transformation Induced Plasticity concept for automotive applications. Following six passes of hot rolling at 850 °C, the Fe-7.9Mn-0.14Si-0.05Al-0.07C (wt.% steel was warm-rolled at 630 °C for seven passes and subsequently air cooled to room temperature. The sample was subsequently intercritically annealed at various temperatures for 30 min to promote the reverse transformation of martensite into austenite. The obtained results show that the highest volume fraction of austenite is 39% for the sample annealed at 600 °C. This specimen exhibits a yield stress of 910 MPa and a high ultimate tensile stress of 1600 MPa, with an elongation-to-failure of 0.29 at a strain rate of 1 × 10−3/s. The enhanced work-hardening ability of the investigated steel is closely related to martensitic transformation and the interaction of dislocations. Especially, the alternate arrangement of acicular ferrite (soft phase and ultrafine austenite lamellae (50–200 nm, strong and ductile phase is the key factor contributing to the excellent combination of strength and ductility. On the other hand, the as-warm-rolled sample also exhibits the excellent combination of strength and ductility, with elongation-to-failure much higher than those annealed at temperatures above 630 °C.

Effects of Intercritical Annealing Temperature on Mechanical Properties of Fe-7.9Mn-0.14Si-0.05Al-0.07C Steel.

Science.gov (United States)

Zhao, Xianming; Shen, Yongfeng; Qiu, Lina; Liu, Yandong; Sun, Xin; Zuo, Liang

2014-12-09

A medium Mn steel has been designed to achieve an excellent combination of strength and ductility based on the TRIP (Transformation Induced Plasticity) concept for automotive applications. Following six passes of hot rolling at 850 °C, the Fe-7.9Mn-0.14Si-0.05Al-0.07C (wt.%) steel was warm-rolled at 630 °C for seven passes and subsequently air cooled to room temperature. The sample was subsequently intercritically annealed at various temperatures for 30 min to promote the reverse transformation of martensite into austenite. The obtained results show that the highest volume fraction of austenite is 39% for the sample annealed at 600 °C. This specimen exhibits a yield stress of 910 MPa and a high ultimate tensile stress of 1600 MPa, with an elongation-to-failure of 0.29 at a strain rate of 1 × 10 -3 /s. The enhanced work-hardening ability of the investigated steel is closely related to martensitic transformation and the interaction of dislocations. Especially, the alternate arrangement of acicular ferrite (soft phase) and ultrafine austenite lamellae (50-200 nm, strong and ductile phase) is the key factor contributing to the excellent combination of strength and ductility. On the other hand, the as-warm-rolled sample also exhibits the excellent combination of strength and ductility, with elongation-to-failure much higher than those annealed at temperatures above 630 °C.

Influencia de la transformación austenita-martensita en la estabilidad dimensional de un nuevo acero para herramientas aleado con niobio (0,08% y vanadio (0,12%

Directory of Open Access Journals (Sweden)

Conejero Ortega, Gerardo

2014-09-01

Full Text Available Austenite-martensite transformation influence on the dimensional stability of a new experimental tool steel alloyed with niobium (0.08% wt. and vanadium (0.12% wt. has been studied. The dimensional stability of this new steel was compared with the dimensional stability of commercial steel, after and before two thermal treatments, T1 (860 °C and T2 (900 °C. The thermal treatments consisted on heating and cooling, at 1 atmosphere of pressure, in N2 atmosphere furnace, fol lowing by heating in a conventional furnace at 180 °C during 1 hour. Initially, the experimental steel composition and Ac1 and Ac3 transformation temperatures were determined by glow-discharge luminescence (GDL and dilatometric tests, respectively, in order to select the austenization temperatures of T1 and T2 treatments. After hardness measurement, the microstructure of both steels was characterized by X-Ray Diffraction (XRD and optical metallography, before and after of T1 and T2 thermal treatments. Finally, longitudinal and angular dimensional stability analyses were realized for both commercial and experimental steels. After a contrastive hypothesis analysis, the results showed that the longitudinal relative variation of the experimental steel calculated was around 0.2% and the angular relative variation was not significantSe ha estudiado la influencia de la transformación de austenita a martensita en la estabilidad dimensional de un acero experimental para herramientas aleado con niobio (0,08% en peso y vanadio (0,12% en peso. La estabilidad dimensional del acero experimental fue comparada con la de un acero comercial antes y después de ser sometidos, ambos aceros, a dos tratamientos térmicos diferentes. Los tratamientos térmicos consistieron en un calentamiento y mantenimiento durante una hora a temperaturas de 860 °C (T1 y 900 °C (T2 y un enfriamiento final en horno con nitrógeno (N2 a 1 atmósfera de presión. Inicialmente, se determinaron las composiciones del

Relaxivity of Ferumoxytol at 1.5 T and 3.0 T.

Science.gov (United States)

Knobloch, Gesine; Colgan, Timothy; Wiens, Curtis N; Wang, Xiaoke; Schubert, Tilman; Hernando, Diego; Sharma, Samir D; Reeder, Scott B

2018-05-01

The aim of this study was to determine the relaxation properties of ferumoxytol, an off-label alternative to gadolinium-based contrast agents, under physiological conditions at 1.5 T and 3.0 T. Ferumoxytol was diluted in gradually increasing concentrations (0.26-4.2 mM) in saline, human plasma, and human whole blood. Magnetic resonance relaxometry was performed at 37°C at 1.5 T and 3.0 T. Longitudinal and transverse relaxation rate constants (R1, R2, R2*) were measured as a function of ferumoxytol concentration, and relaxivities (r1, r2, r2*) were calculated. A linear dependence of R1, R2, and R2* on ferumoxytol concentration was found in saline and plasma with lower R1 values at 3.0 T and similar R2 and R2* values at 1.5 T and 3.0 T (1.5 T: r1saline = 19.9 ± 2.3 smM; r1plasma = 19.0 ± 1.7 smM; r2saline = 60.8 ± 3.8 smM; r2plasma = 64.9 ± 1.8 smM; r2*saline = 60.4 ± 4.7 smM; r2*plasma = 64.4 ± 2.5 smM; 3.0 T: r1saline = 10.0 ± 0.3 smM; r1plasma = 9.5 ± 0.2 smM; r2saline = 62.3 ± 3.7 smM; r2plasma = 65.2 ± 1.8 smM; r2*saline = 57.0 ± 4.7 smM; r2*plasma = 55.7 ± 4.4 smM). The dependence of relaxation rates on concentration in blood was nonlinear. Formulas from second-order polynomial fittings of the relaxation rates were calculated to characterize the relationship between R1blood and R2 blood with ferumoxytol. Ferumoxytol demonstrates strong longitudinal and transverse relaxivities. Awareness of the nonlinear relaxation behavior of ferumoxytol in blood is important for ferumoxytol-enhanced magnetic resonance imaging applications and for protocol optimization.

Microstructural defect evolution in neutron – Irradiated 12Cr18Ni9Ti stainless steel during subsequent isochronous annealing

Energy Technology Data Exchange (ETDEWEB)

Tsay, K.V.; Maksimkin, O.P.; Turubarova, L.G.; Rofman, O.V. [Institute of Nuclear Physics NNC RK, Almaty (Kazakhstan); Garner, F.A., E-mail: frank.garner@dslextreme.com [Radiation Effects Consulting, Richland, WA (United States)

2013-08-15

Transmission electron microscopy and microhardness measurements were used to examine changes in microstructure and associated strengthening induced in austenitic stainless steel 12Cr18Ni9Ti irradiated to ∼0.001 and ∼5 dpa in the WWR-K reactor before and after being subjected to post-irradiation isochronal annealing. The relatively low values of irradiation temperature and dpa rate (∼80 °C and ∼1.2 × 10{sup −8} dpa/s) experienced by this steel allowed characterization of defect microstructures over a wide range of defect ensembles, all at constant composition, produced first by irradiation and then by annealing at temperatures between 450 and 1050 °C. It was shown that the dispersed barrier hardening model with commonly accepted physical properties successfully predicted the observed hardening. It was also observed that when TiC precipitates form at higher annealing temperatures, the alloy does not change in hardness, reflecting a balance between precipitate-hardening and matrix-softening due to removal of solute-strengthening elements titanium and carbon. Such matrix-softening is not often considered in other studies, especially where the contribution of precipitates to hardening is a second-order effect.

Microstructural defect evolution in neutron – Irradiated 12Cr18Ni9Ti stainless steel during subsequent isochronous annealing

International Nuclear Information System (INIS)

Tsay, K.V.; Maksimkin, O.P.; Turubarova, L.G.; Rofman, O.V.; Garner, F.A.

2013-01-01

Transmission electron microscopy and microhardness measurements were used to examine changes in microstructure and associated strengthening induced in austenitic stainless steel 12Cr18Ni9Ti irradiated to ∼0.001 and ∼5 dpa in the WWR-K reactor before and after being subjected to post-irradiation isochronal annealing. The relatively low values of irradiation temperature and dpa rate (∼80 °C and ∼1.2 × 10 −8 dpa/s) experienced by this steel allowed characterization of defect microstructures over a wide range of defect ensembles, all at constant composition, produced first by irradiation and then by annealing at temperatures between 450 and 1050 °C. It was shown that the dispersed barrier hardening model with commonly accepted physical properties successfully predicted the observed hardening. It was also observed that when TiC precipitates form at higher annealing temperatures, the alloy does not change in hardness, reflecting a balance between precipitate-hardening and matrix-softening due to removal of solute-strengthening elements titanium and carbon. Such matrix-softening is not often considered in other studies, especially where the contribution of precipitates to hardening is a second-order effect

The comparison of 18C(n; γ)19C and 18C(α; n)21O reaction rates: consequences for the r-process

International Nuclear Information System (INIS)

Dan, M.; Singh, G.; Chatterjee, R.; Shubhchintak

2017-01-01

Neutron rich light and medium mass nuclei play a major role in determining the reaction flow towards the r-process seed nuclei production. In this text, we calculate the neutron capture rate of 18 C and compare it with that of α-capture by the same nucleus in the temperature range T 9 = 0:1 - 10. This temperature range roughly equals to an energy range of 1 keV to 1 MeV in centre of mass frame, where it is very difficult to perform direct reaction experiments. Further, the theoretical construction of 18 C-n continuum state for the 18 C(n; γ) 19 C direct reaction is a tedious job

Investigation of technology for manufacturing the non-magnetic temperature-sensitive composite materials and their properties

International Nuclear Information System (INIS)

Kobelev, A.G.; Kolesnikov, F.V.; Gul'bin, V.N.; Nikitin, I.S.

2004-01-01

Investigation results are presented on structure and properties of nonmagnetic thermobimetals on the basis of beryllium bronze which is used both as active and passive layers. The second layer of thermosensitive element consists of stainless steel 12Kh18N10T, titanium base alloy VT1-0 and aluminum base alloy AD1. The manufacturing of the layered composite materials includes explosion welding, plastic deformation and heat treatment. It is established that strain hardening of the thermobimetals results in an increase of yield strength, microstresses, hardness and specific resistance [ru

Surface deformation effects on stainless steel, Ni, Cu and Mo produced by medium energy He ions irradiation

International Nuclear Information System (INIS)

Constantinescu, B.; Florescu, V.; Sarbu, C.

1993-01-01

To investigate dose and energy dependence of surface deformation effects (blistering and flaking), different kinds of candidate CTR first wall materials as 12KH18N10T, W-4541, W-4016 and SS-304 stainless steels, Ni, Cu, Mo were irradiated at room temperature with 3.0, 4.7 and 6.8 MeV He + ions at IAP Cyclotron. The effects were investigated by means of a TEMSCAN 200 CX electron microscope and two metallographic Orthoplan Pol Leitz and Olympus microscopes. We observed two dose dependent main phenomena: blistering and flaking (craters). So, blisters occurrence on the irradiated surface is almost instantaneous when a critical dose (number of He ions accumulated in the region at the end of alpha particles range) is reached. Increasing irradiation dose, we reached flaking stage. So, isolated submicronic fissures along grain boundaries were observed on the blister skin, chronologically followed by large (5-20 μm) deep cracks of hundreds of microns in length, blisters opening and, finally, flaking appearance. (author) 8 figs., 1 tab

Increasing the brittle fracture resistance in manual arc welding and heat treatment of type 12KhM steels

International Nuclear Information System (INIS)

Tikhonov, V.P.; Bychenkova, G.A.; Gordeev, Y.V.; Ilyuhov, C.V.

1984-01-01

The extensive application of heat-resisting steels is delayed by their poor weldability. Optimum technology has been developed for manual arc welding and heat treatment of structures of type 12KhM steels resulting in high cracking resistance. Trials were conducted to evaluate the efficiency of removing the structural stresses in tempering the structures. On the basis of the experimental results, it may be assumed that the toughness properties of the welded joints produced by manual arc welding can be improved by optimizing the alloying system of the weld metal, with the parent metal treated in the optimum heat treatment conditions. The aim of subsequent investigations was to assess the properties of the weld metal made with vanadium-free electrodes. It was found that the impact toughness increased two to three times; the mean hardness and the maximum hardness were both less than 220. The reduction in hardness and increase of the toughness properties of the metal are caused by the lower degree of hardening of the bulk of the grain and, consequently, by the lower concentration of plastic strain at the grain boundaries

Structural, magnetic and transport properties of Mn3.1Sn0.9 and Mn3.1Sn0.9N compounds

International Nuclear Information System (INIS)

Feng, W.J.; Li, D.; Ren, W.J.; Li, Y.B.; Li, W.F.; Li, J.; Zhang, Y.Q.; Zhang, Z.D.

2007-01-01

The cubic anti-perovskite Mn 3.1 Sn 0.9 N compound is prepared via nitrogenation of the hexagonal Mn 3.1 Sn 0.9 compound. A magnetic phase diagram of Mn 3.1 Sn 0.9 compound is constructed by analysis of data of its magnetic properties. For Mn 3.1 Sn 0.9 N compound, parasitic ferromagnetism exists in the temperature range of 5-370 K, besides a spin-reorientation at about 280 K. Mn 3.1 Sn 0.9 compound exhibits a metallic conducting behavior, while Mn 3.1 Sn 0.9 N displays a metal-nonmetal transition due to the electron localization caused by the static disorder. The differences of the physical properties between the both compounds, are discussed, in terms of the correlation of the hexagonal DO 19 and the cubic anti-perovskite structures, the reduction of the distances between Mn atoms, and the spin-pairing or charge transfer effect due to the electron donation by N 2p to Mn 3d states after introduction of N atoms into the interstitial sites of Mn 3.1 Sn 0.9 compound

Ultrafast carrier dynamics in a GaN/Al 0.18Ga0.82N superlattice

Science.gov (United States)

Mahler, Felix; Tomm, Jens W.; Reimann, Klaus; Woerner, Michael; Elsaesser, Thomas; Flytzanis, Christos; Hoffmann, Veit; Weyers, Markus

2018-04-01

Relaxation processes of photoexcited carriers in a GaN /Al0.18Ga0.82N superlattice are studied in femtosecond spectrally resolved reflectivity measurements at ambient temperature. The transient reflectivity reveals electron trapping into defect states close to the conduction-band minimum with a 150-200 fs time constant, followed by few-picosecond carrier cooling. A second slower trapping process into a different manifold of defect states is observed on a time scale of approximately 10 ps. Our results establish the prominent role of structural defects and disorder for ultrafast carrier dynamics in nitride semiconductor structures.

Is vaccenic acid (18:1t n-7) associated with an increased incidence of hip fracture? An explanation for the calcium paradox.

Science.gov (United States)

Hamazaki, Kei; Suzuki, Nobuo; Kitamura, Kei-Ichiro; Hattori, Atsuhiko; Nagasawa, Tetsuro; Itomura, Miho; Hamazaki, Tomohito

2016-06-01

High calcium intake may increase hip fracture (HF) incidence. This phenomenon, known as the calcium paradox, might be explained by vaccenic acid (18:1t n-7, VA), the highly specific trans fatty acid (TFA) present in dairy products. First, we ecologically investigated the relationship between 18:1 TFA intake and HF incidence using data from 12 to 13 European countries collected before 2000; then we measured the effects of VA and elaidic acid (18:1t n-9, EA) on osteoblasts from goldfish scales (tissues very similar to mammalian bone), with alkaline phosphatase as a marker; and finally we measured the effect of VA on mRNA expression in the scales for the major bone proteins type I collagen and osteocalcin. HF incidence was significantly correlated with 18:1 TFA intake in men (r=0.57) and women (r=0.65). Incubation with 1μmol/L VA and EA for 48h significantly decreased alkaline phosphatase activity by 25% and 21%, respectively. Incubation of scales with 10μmol/L VA for 48h significantly decreased mRNA expression for type I collagen and osteocalcin (by about 50%). In conclusion, VA may be causatively related to HF and could explain the calcium paradox. It may be prudent to reduce 18:1 TFA intake, irrespective of trans positions, to prevent HF. Copyright © 2016 Elsevier Ltd. All rights reserved.

Random cyclic constitutive models of 0Cr18Ni10Ti pipe steel

International Nuclear Information System (INIS)

Zhao Yongxiang; Yang Bing

2004-01-01

Experimental study is performed on the random cyclic constitutive relations of a new pipe stainless steel, 0Cr18Ni10Ti, by an incremental strain-controlled fatigue test. In the test, it is verified that the random cyclic constitutive relations, like the wide recognized random cyclic strain-life relations, is an intrinsic fatigue phenomenon of engineering materials. Extrapolating the previous work by Zhao et al, probability-based constitutive models are constructed, respectively, on the bases of Ramberg-Osgood equation and its modified form. Scattering regularity and amount of the test data are taken into account. The models consist of the survival probability-strain-life curves, the confidence strain-life curves, and the survival probability-confidence-strain-life curves. Availability and feasibility of the models have been indicated by analysis of the present test data

Radiotherapy or surgery for T2N0M0 glottic carcinoma?

International Nuclear Information System (INIS)

Stalpers, L.J.A.; Daal, W.A.J. van; Verbeek, A.L.M.

1989-01-01

Decision analysis was used to evaluate the results of treatment of T 2 N 0 M 0 glottic carcinoma as presented in the literature. Based on mean values for recurrence, salvage eligibility after recurrence and salvage success, the 5-year survival after radiotherapy and surgery proved to be almost identical, 85 and 86%. If the recurrence rates and the salvage rates were varied, a marginal advantage for surgery in small tumours and a major advantage in more extended tumours was seen if only survival is considered. To take the quality of speech into account, a utility analysis was performed. A utility scale was defined ranging from 0.0 as the value for death, to 1.0 for a successfully irradiated patient with preservation of normal speech. A utility of 0.99 or less for the laryngectomized patient would favour radiotherapy over surgery for all T 2 tumours. In patients with T 2b tumours and in extreme circumstances, e.g. if failure rates of radiotherapy are extremely low, an exact assessment of patient utilities may be pivotal. Under normal circumstances radiotherapy is preferred for T 2 N 0 M 0 glottic carcinoma if both survival and the quality of speech are taken into account. (author). 39 refs.; 5 figs.; 1 tab

Corrosion resistance of metals and alloys in molten alkalies

International Nuclear Information System (INIS)

Zarubitskij, O.G.; Dmitruk, B.F.; Minets, L.A.

1979-01-01

Literature data on the corrosion of non-ferrous and noble metals, iron and steels in the molten alkalis and mixtures of their base are presented. It is shown that zirconium, niobium and tantalum are characterized by high corrosion stability in the molten NaOH. Additions of NaOH and KOH to the alkali chloride melts result in a 1000 time decrease of zirconium corrosion rate at 850 deg. The data testify to the characteristic passivating properties of OH - ions; Mo and W do not possess an ability to selfpassivation in hydroxide melts. Corrosion resistance of carbon and chromium-nickel steels in hydroxide melts depends considerably on the temperature, electrolyte composition and atmosphere over them. At the temperatures up to 600 deg C chromium-nickel steel is corrosion resistant in the molten alkali only in the inert atmosphere. Corrosion rate of chromium-nickel alloy is the lower the less chromium and the more nickel it contains. For the small installations the 4Kh18N25S2 and Kh23N28M3D3T steels can be recommended

Removal of corrosion products of construction materials in heat carrier

International Nuclear Information System (INIS)

1975-01-01

A review of reported data has been made on the removal of structural material corrosion products into the heat-carrying agent of power reactors. The corrosion rate, and at the same time, removal of corrosion products into the heat-carrying agent (water) decreases with time. Thus, for example, the corrosion rate of carbon steel in boiling water at 250 deg C and O 2 concentration of 0.1 mg/1 after 3000 hr is 0.083 g/m 2 . day; after 9000 hr the corrosion rate has been reduced 2.5 times. Under static conditions the transfer rate of corrosion products into water has been smaller than in the stream and also depends on time. The corrosion rate of carbon steel under nuclear plant operating conditions is almost an order higher over that of steel Kh18N10T

Martensite transformation kinetics in 9Cr–1.7W–0.4Mo–Co ferritic steel

Energy Technology Data Exchange (ETDEWEB)

Gao, Qiuzhi, E-mail: neuqgao@163.com [School of Resources and Materials, Northeastern University at Qinhuangdao, Qinhuangdao, Hebei 066000 (China); Wang, Cong; Qu, Fu; Wang, Yingling [School of Resources and Materials, Northeastern University at Qinhuangdao, Qinhuangdao, Hebei 066000 (China); Qiao, Zhixia [School of Mechanical Engineering, Tianjin University of Commerce, Tianjin 300134 (China)

2014-10-15

Highlights: • The obtained M{sub s} temperatures of samples austenitized at 1150 °C are higher than at 900 °C. • Martensite-start transformation is slower for austenitizing at 1150 °C than at 900 °C. • Martensite transformation was controlled by nucleation rate. • Growth of martensite plates was controlled by thermal activation of atoms. - Abstract: Martensite transformation features in the 9Cr–1.7W–0.4Mo–Co ferritic steel, was conducted on a Netzsch Differential Thermal Analysis (DTA), after austenitized at 900 °C and 1150 °C followed by cooling at various rates to room temperature were studied. A martensite transformation kinetics model based on assumption of continuous nucleation and consideration of impingement was introduced to investigate the influence of austenitizing temperature and cooling rate on the martensite transformation behaviors. The obtained interface velocity and the activation energy for interface-controlling growth are lower than 10{sup −5} m/s and 40 kJ/mol, respectively, according to the fitted data. Both indicated that martensite transformation in the 9Cr–1.7W–0.4Mo–Co ferritic steel was controlled by nucleation rate, and that growth of plates was controlled by thermal activation of atoms.

Martensite transformation kinetics in 9Cr–1.7W–0.4Mo–Co ferritic steel

International Nuclear Information System (INIS)

Gao, Qiuzhi; Wang, Cong; Qu, Fu; Wang, Yingling; Qiao, Zhixia

2014-01-01

Highlights: • The obtained M s temperatures of samples austenitized at 1150 °C are higher than at 900 °C. • Martensite-start transformation is slower for austenitizing at 1150 °C than at 900 °C. • Martensite transformation was controlled by nucleation rate. • Growth of martensite plates was controlled by thermal activation of atoms. - Abstract: Martensite transformation features in the 9Cr–1.7W–0.4Mo–Co ferritic steel, was conducted on a Netzsch Differential Thermal Analysis (DTA), after austenitized at 900 °C and 1150 °C followed by cooling at various rates to room temperature were studied. A martensite transformation kinetics model based on assumption of continuous nucleation and consideration of impingement was introduced to investigate the influence of austenitizing temperature and cooling rate on the martensite transformation behaviors. The obtained interface velocity and the activation energy for interface-controlling growth are lower than 10 −5 m/s and 40 kJ/mol, respectively, according to the fitted data. Both indicated that martensite transformation in the 9Cr–1.7W–0.4Mo–Co ferritic steel was controlled by nucleation rate, and that growth of plates was controlled by thermal activation of atoms

Application of experiment planning during investigation of cementation process in solid carburizers

International Nuclear Information System (INIS)

Lisenkov, A.N.; Denisov, V.M.; Prigozhina, E.L.

1981-01-01

A mathematical model of cementation process in solid carburizirs is obtained, the most effective contents of carburizers are chosen. Specimens are produced out of St20, 12KhN3A, 40Kh13, KhVG steels. It is shown that specimens of St20 and 12KhN3A steels have the higher depth of cementated layer, specimens made of 40Kh13 and KhVG steels-the lower depth. It is shown that the quality of cementated layer structure at recommended regimes improved, cementated layer depth for low-carbon steels changed a little and for tool steels increased infficiently: for KhVG steel in 2-3 times for 40Kh13 steel in 1.5-2.5 times

Measurements of nitrogen depth distribution in the surface of steel with the 14N(d,p0)15N reaction

International Nuclear Information System (INIS)

Didriksson, R.; Goenczi, L.; Sundqvist, B.

1980-01-01

The 14 N(d,p 0 ) 15 N nuclear reaction has been used to measure the nitrogen depth distribution in the surface of steel samples. With a beam energy of 2.5 MeV a depth of 15μm could be analyzed. The depth resolution was 0.7 μm (FWHM) and nitrogen contents down to 0.02 percent could be determined. (author)

The nT1 translocation separates vulval regulatory elements from the egl-18 and elt-6 GATA factor genes.

Science.gov (United States)

Koh, Kyunghee; Bernstein, Yelena; Sundaram, Meera V

2004-03-01

egl-18 and elt-6 are partially redundant, adjacent genes encoding GATA factors essential for viability, seam cell development, and vulval development in Caenorhabditis elegans. The nT1 reciprocal translocation causes a strong Vulvaless phenotype, and an nT1 breakpoint was previously mapped to the left arm of LGIV, where egl-18/elt-6 are located. Here we present evidence that the nT1 vulval phenotype is due to a disruption of egl-18/elt-6 function specifically in the vulva. egl-18 mutations do not complement nT1 for vulval defects, and the nT1 breakpoint on LGIV is located within approximately 800 bp upstream of a potential transcriptional start site of egl-18. In addition, we have identified a approximately 350-bp cis-regulatory region sufficient for vulval expression just upstream of the nT1 breakpoint. By examining the fusion state and division patterns of the cells in the developing vulva of nT1 mutants, we demonstrate that egl-18/elt-6 prevent fusion and promote cell proliferation at multiple steps of vulval development.

Roentgenoelectronic investigation into oxidation of iron-chromium and iron-chromium-nickel alloys

International Nuclear Information System (INIS)

Akimov, A.G.; Rozenfel'd, I.L.; Kazanskij, L.P.; Machavariani, G.V.

1978-01-01

Kinetics of iron-chromium and iron-chromium-nickel alloy oxidation (of the Kh13 and Kh18N10T steels) in oxygen was investigated using X-ray electron spectroscopy. It was found that according to X-ray electron spectra chromium oxidation kinetics in the iron-chromium alloy differs significantly from oxidation kinetics of chromium pattern. Layer by layer X-ray electron analysis showed that chromium is subjected to a deeper oxidation as compared to iron, and accordingly, Cr 2 O 3 layer with pure iron impregnations is placed between the layer of mixed oxide (Fe 3 O 4 +Cr 2 O 3 ) and metal. A model of the iron-chromium alloy surface is suggested. The mixed oxide composition on the steel surface is presented as spinel Fesub(2+x)Crsub(1-x)Osub(y)

Effect of high-temperature exposure on the mechanical properties of 18Cr–8Ni–W–Nb–V–N stainless steel

International Nuclear Information System (INIS)

Nikulin, I.; Kipelova, A.; Kaibyshev, R.

2012-01-01

Highlights: ► Niobium stabilized 18Cr–8Ni austenitic steel was subjected to long-time aging. ► The main phases precipitated during aging are Z-phase and Laves-phase. ► Intragranular phases and solid solution are responsible for tensile strength. ► Intergranular particles affect impact toughness. - Abstract: The change in the mechanical properties of 18Cr–8Ni–W–Nb–V–N austenitic stainless steel due to aging was investigated at room temperature and 650 °C. It was shown that long-term aging decreases strength characteristics despite increasing hardness. The impact toughness decreases from 255 J/cm 2 for an un-aged steel to 135 J/cm 2 for the steel aged for 3000 h. However, evidence of ductile fracture was found even after long-term aging. This study suggests that the reduction in impact toughness occurs due to the precipitation of Z-phase and Laves-phase particles at the grain boundaries. The degradation of impact toughness and mechanical properties with aging is discussed in terms of microstructure evolution, secondary phase precipitations and fracture mechanisms.

Creep Tests and Modeling Based on Continuum Damage Mechanics for T91 and T92 Steels

Science.gov (United States)

Pan, J. P.; Tu, S. H.; Zhu, X. W.; Tan, L. J.; Hu, B.; Wang, Q.

2017-12-01

9-11%Cr ferritic steels play an important role in high-temperature and high-pressure boilers of advanced power plants. In this paper, a continuum damage mechanics (CDM)-based creep model was proposed to study the creep behavior of T91 and T92 steels at high temperatures. Long-time creep tests were performed for both steels under different conditions. The creep rupture data and creep curves obtained from creep tests were captured well by theoretical calculation based on the CDM model over a long creep time. It is shown that the developed model is able to predict creep data for the two ferritic steels accurately up to tens of thousands of hours.

Heat treatment effect on the properties of the EhP767 maraging steel welded joints

International Nuclear Information System (INIS)

Taver, E.I.; Piskarev, M.N.; Yushchenko, K.A.; Pustovit, A.I.; Anisimova, M.S.

1977-01-01

Heat treatment effect on properties of welded joints of maraging 03Kh13N4K13M3T (EhP767) steel with yield strength over 150 kgs/mm 2 has been investigated. It is shown, that change in impact strength of aged joints at - 196 deg C depends on the amount of residual austenite and grain size. To stabilize 20-40 % residual austenite heat treatment regimes have been developed. Recommended are quenching at 1030-1050 deg C, sub-zero treatment and aging at 520 deg C for 16 hrs

Study of regularities in propagation of thermal fatigue cracks

International Nuclear Information System (INIS)

Tachkova, N.G.; Sobolev, N.D.; Egorov, V.I.; Rostovtsev, Yu.V.; Ivanov, Yu.S.; Sirotin, V.L.

1978-01-01

Regularities in the propagation of thermal fatigue cracks in the Cr-Ni steels of the austenite class depending upon deformation conditions in the crack zone, have been considered. Thin-walled tube samples of the Kh16N40, Kh18N20 and Kh16N15 steels have been tested in the 10O reversible 400 deg C and 100 reversible 500 deg C regimes. The samples have possessed a slot-shaped stress concentrator. Stress intensity pseudocoefficient has been calculated for the correlation of experimental data. The formula for determining crack propagation rate has been obtained. The experiments permit to conclude that propagation rate of thermal fatigue cracks in the above steels depends upon the scope of plastic deformation during a cycle and stress intensity pseudocoefficient, and is determined by plastic deformation resistance during thermal cyclic loading

SCC growth behavior of cast stainless steels in high-temperature water. Influences of corrosion potential, steel type, thermal aging and cold-work

International Nuclear Information System (INIS)

Yamada, Takuyo; Terachi, Takumi; Miyamoto, Tomoki; Arioka, Koji

2011-01-01

Recent studies on crack growth rate (CGR) measurement in oxygenated high-temperature pure water conditions, such as normal water chemistry (NWC) in BWRs, using compact tension (CT) type specimens have shown that stainless steel weld metal are susceptible to stress corrosion cracking (SCC). On the other hand, the authors reported that no significant SCC growth was observed on stainless steel weld metals in PWR primary water at temperatures from 250degC to 340degC. Cast austenitic stainless steels are widely used in light water reactors, and there is a similarity between welded and cast stainless steels in terms of the microstructure of the ferrite/austenite duplex structure. However, there are a few reports giving CGR data on cast stainless steels in the BWRs and PWRs. The principal purpose of this study was to examine the SCC growth behavior of cast stainless steels in simulated PWR primary water. A second objective was to examine the effects on SCC growth in hydrogenated and oxygenated water environments at 320degC of: (1) corrosion potential; (2) steels type (Mo in alloy); (3) thermal-aging (up to 400degC x 40 kh); and (4) cold-working (10%). The results were as follows: (1) No significant SCC growth was observed on all types of cast stainless steels: aged (400degC x 40 kh) of SCS14A and SCS13A and 10% cold-working, in hydrogenated (low-potential) water at 320degC. (2) Aging at 400degC x 40 kh SCS14A (10%CW) markedly accelerated the SCC growth of cast material in high-potential water at 320degC, but no significant SCC growth was observed in the hydrogenated water, even after long-term thermal aging (400degC x 40 kh). (3) Thus, cast stainless steels have excellent SCC resistance in PWR primary water. (4) On the other hand, significant SCC growth was observed on all types of cast stainless steels: 10%CW SCS14A and SCS13A, in 8 ppm-oxygenated (high-potential) water at 320degC. (5) No large difference in SCC growth was observed between SCS14A (Mo) and SCS13A. (6) No

On abnormal decomposition of supercooled austenite in carbon and alloy steels

International Nuclear Information System (INIS)

Parusov, V.V.; Dolzhenkov, I.I.; Podobedov, L.V.; Vakulenko, I.A.

1980-01-01

Residual stresses which appear as a result of thermal cycling in the temperature range of 300-700 deg C are investigated in an austenitic class steel (03Kh18N11) to ground the assumption on the effect of plastic deformation, appearing due to thermal stresses, on the mechanism of supercooled austenite decomposition. The determination of residual stresses is carried out with the help of X-ray diffraction analysis. It is established that the deformation brings about an increase in density of dislocation the interaction of which leads to the formation of a typical austenite substructure which conditions the proceeding of the eutectoid transformation according to an abnormal mechanism. It is noted, that the grain pearlite formation due to plastic and microplastic deformation of supercooled austenite induced by thermal stresses should be taken into account when developing steel heat treatment shedules [ru

Theoretical study of [Li(H2O)n]+ and [K(H2O)n]+ (n = 1-4) complexes

International Nuclear Information System (INIS)

Wojcik, M.J.; Mains, G.J.; Devlin, J.P.

1995-01-01

The geometries, successive binding energies, vibrational frequencies, and infrared intensities are calculated for the [Li(H 2 O) n ] + and [K(H 2 O) n ] + (n = 1-4) complexes. The basis sets used are 6-31G * and LANL1DZ (Los Alamos ECP+DZ) at the SCF and MP2 levels. There is an agreement for calculated structures and frequencies between the MP2/6-31G * and MP2/LANL1DZ basis sets, which indicates that the latter can be used for calculations of water complexes with heavier ions. Our results are in a reasonable agreement with available experimental data and facilitate experimental study of these complexes. 19 refs., 4 figs., 6 tabs

Strength of joints brazed with two-phase solders

International Nuclear Information System (INIS)

Shnyakin, N.S.; Parfenova, L.V.; Ekatova, A.S.; Prilepskaya, I.V.

1976-01-01

Dependence of the structure and strength of soldered joints upon a gap size in case of 1Kh18N10T stainless steel soldering with a double-phase solder of Ni-Zn-Cu system is described. Butt and lap joints have been subjected to soldering with gas-flame and induction heating. The optimum conditions of the solder crystallization are determined with wedge-gap samples. The studies show that the character of distribution of a fusible β-phase in metal depends upon a gap size. With gaps up to 0.1 mm the β-phase enriched with a fusible component (zinc) runs as a continuous thin interlayer in the middle of the seam. As a result of zinc evaporation from the β-phase this interlayer becomes internally oxidized. After the sample is broken an oxidized fracture gives one the impression of a poor fusion in the middle part of the joint. The ultimate strength of butt joints is 15-20 kgf/sq.mm. A value of thermal expansion of 1Kh18N10T steel samples, 1-5 mm thick, has been experimentally determined for butt soldering. The elongation of two halves of the sample is measured by an indicator and proved to be 0.89 mm for a 50x50x2 mm sample at a soldering temperature of 1.100 deg C. The paper presents methods for the calculation of an optimal gap value for butt soldering with a local gas-flame and induction heating

The influence of interstitial impurities on temperature ranges of deuterium retention in austenitic stainless steel 18Cr10NiTi

International Nuclear Information System (INIS)

Neklyudov, I.M.; Morozov, O.M.; Kulish, V.G.; Zhurba, V.I.; Galytsky, A.G.; Piatenko, E.V.

2009-01-01

The influence of nitrogen, oxygen and helium on the temperature range of deuterium retention in 18Cr10NiTi stainless steel (of AISI304L type) has been investigated. It is demonstrated that the introduction of oxygen, nitrogen or helium into 18Cr10NiTi steel extends the upper limit in the high-temperature range of deuterium retention. It has been found that for 18Cr10NiTi stainless steel, pre-irradiated with helium ions, the increase in the temperature range of deuterium retention occurs in steps: on attainment of helium concentration of ∼0.5 at.% He the temperature range increases by ∼100 K, and on attainment of helium concentration of ∼2.5 at.% He the temperature range increases by ∼350 K. The introduction of oxygen into 18Cr10NiTi stainless steel results in the increase of the temperature range of deuterium retention in the direction of rise in temperature. In the deuterium thermodesorption spectrum, this manifests itself by the occurrence of an additional low-amplitude peak with the maximum temperature T m ∼ 560 K. The introduction of nitric impurity into 18Cr10NiTi stainless steel results in the extension of the temperature range of deuterium retention towards higher temperatures.

Creep deformation behavior at long-term in P23/T23 steels

Energy Technology Data Exchange (ETDEWEB)

Sawada, K.; Tabuchi, M.; Kimura, K. [National Institute for Materials Science (Japan)

2008-07-01

Creep behavior of ASME P23/T23 steels was investigated and analyzed, focusing on creep strength degradation at long-term. Creep rupture strength at 625 C and 650 C dropped at long-term in both P23 and T23 steels. The stress exponent of minimum creep rate at 625 C and 650 C was 7.8-13 for higher stresses and 3.9-5.3 for lower stresses in the P23/T23 steels. The change of stress exponent with stress levels was consistent with the drop in creep rupture strength at long-term. The Monkman-Grant rule was confirmed in the range examined in P23 steel, while the data points deviated from the rule at long-term in the case of T23 steel. The creep ductility of P23 steel was high over a wide stress and temperature range. On the other hand, in T23 steel, creep ductility at 625 C and 650 C decreased as time to rupture increased. The change in ductility may cause the deviation from the Monkman-Grant rule. Fracture mode changed from transgranular to intergranular fracture in the long-term at 625 C and 650 C. (orig.)

Precipitation process of Z-phase in 9-12%CR steels

DEFF Research Database (Denmark)

Danielsen, Hilmar Kjartansson

2014-01-01

Precipitation of Z-phase, Cr(V,Nb)N, is known to negatively affect creep properties of 9-12%Cr steels for power plant applications as it dissolves finely distributed MX particles, (V,Nb)N, especially in high Cr steels. As the Z-phase precipitates slowly as large particles, this causes a net drop ...... and crystallographically into Z-phase CrTaN particles. Copyright © 2014 Electric Power Research Institute, Inc. Distributed by ASM International®. All rights reserved....

Calculation and experimental technique of determination of rolling procedure for cold-rolling tube mills

International Nuclear Information System (INIS)

Igoshin, V.F.; Aleshin, V.A.; Khoroshikh, Yu.G.; Bogatov, A.A.; Mizhiritskij, O.I.

1983-01-01

Calculation and experimental technique of determination of tube cold rolling procedure has been developed. Rolling procedure based on the usage of regression equation epsilon=1.24 psi, where psi is the relative reduction of area, delta-permissible reduction during rolling, has been tested on 08Kh18N10T steel. The effect of tube geometry, tool calibration parameters, lubrication conditions etc. on metal deformability in taking into account experimentally. The use of the technique proposed has allowed to shorten the time of mastering of the production of tubes from different steels

Room and elevated temperature Mechanical Behavior of 9-12% Cr Steels

Energy Technology Data Exchange (ETDEWEB)

Dogan, Omer N.; Hawk, Jeffrey A.; Schrems, Karol K.

2005-02-01

The mechanical properties of medium Cr steels used in fossil fired power plants are very good because of their excellent high temperature microstructural stability. However, as the desire to increase the operating temperature (>650C) of the plant goes up, the need for steels that maintain their strength at these temperatures also increases. The mechanical properties of three medium Cr steels (0.08C-(9-12)Cr-1.2Ni-0.7Mo-3.0Cu-3.0Co-0.5Ti) were investigated through hardness, hot hardness and tensile measurements. The strength of the 9-12%Cr steels at room temperature after long-term isothermal aging (750C; 1000 hours) compares favorably with that of other power plant steels (e.g., P91). In addition, the elevated temperature strength and hot hardness also behave similarly. The mechanical behavior will be discussed in terms of the strength, elongation and tensile fracture characteristics.

Role of grain refinement in hardening of structural steels at preliminary thermomechanical treatment

International Nuclear Information System (INIS)

Bukhvalov, A.B.; Grigor'eva, E.V.; Davydova, L.S.; Degtyarev, M.V.; Levit, V.I.; Smirnova, N.A.; Smirnov, L.V.

1981-01-01

The hardening mechanism during preliminary thermomechanical treatment with deformation by cold rolling or hydroextrusion is studied on structural 37KhN3M1 and 38KhN3MFA steels. Specimens have been tested on static tension, impact strength and fracture toughness. It is shown that hydroextrusion application instead of rolling does not change the hardening effect of preliminary thermomechanical treatment (PTMT). It is established that the increase of preliminary deformation degree and the use of accelerated short term hardening heating provides a bett er grain refinement and the increase of PTMT hardening effect [ru

Device for measuring high temperature heat conductivity of solids and melts

International Nuclear Information System (INIS)

Magomedov, Ya.B.; Gadzhiev, G.G.

1990-01-01

A modification of a device for measuring heat conductivity by a compensation method when a thermocouple with gadolinium sulfide being used is suggested. Such a device has less error of measurement (8%), wider interval of working temperatures (300-1600K) and it permits to investigate the material in the wide range of heat conductivity values (0.5-30 W/(mxK)). The stainless steel 12Kh18N10T, lanthanum sulfide and melted quartz were used for the device calibration. The results obtained and the literature data on these materials agree well between each other

Movement of liquid metal in welding bath during welding in longitudinal magnetic field

International Nuclear Information System (INIS)

Kovalev, I.M.; Rybakov, A.S.

1977-01-01

The specific features are considered of liquid metal flow in a bath during welding of steel 12Kh18N10T plates with a non-consumable electrode in argon under interaction of the arc and bath with a longitudinal constant magnetic field. In controlling the velocity field of metal flow, the longitudinal magnetic field permits to form a seam at automatic welding of horizontal joints on a vertical plane

Elevated temperature tensile properties of P9 steel towards ferritic steel wrapper development for sodium cooled fast reactors

Energy Technology Data Exchange (ETDEWEB)

Choudhary, B.K., E-mail: bkc@igcar.gov.in; Mathew, M.D.; Isaac Samuel, E.; Christopher, J.; Jayakumar, T.

2013-11-15

Tensile deformation and fracture behaviour of the three developmental heats of P9 steel for wrapper applications containing varying silicon in the range 0.24–0.60% have been examined in the temperature range 300–873 K. Yield and ultimate tensile strengths in all the three heats exhibited gradual decrease with increase in temperature from room to intermediate temperatures followed by rapid decrease at high temperatures. A gradual decrease in ductility to a minimum at intermediate temperatures followed by an increase at high temperatures has been observed. The fracture mode remained transgranular ductile. The steel displayed signatures of dynamic strain ageing at intermediate temperatures and dominance of recovery at high temperatures. No significant difference in the strength and ductility values was observed for varying silicon in the range 0.24–0.60% in P9 steel. P9 steel for wrapper application displayed strength and ductility values comparable to those reported in the literature.

Elevated temperature tensile properties of P9 steel towards ferritic steel wrapper development for sodium cooled fast reactors

Science.gov (United States)

Choudhary, B. K.; Mathew, M. D.; Isaac Samuel, E.; Christopher, J.; Jayakumar, T.

2013-11-01

Tensile deformation and fracture behaviour of the three developmental heats of P9 steel for wrapper applications containing varying silicon in the range 0.24-0.60% have been examined in the temperature range 300-873 K. Yield and ultimate tensile strengths in all the three heats exhibited gradual decrease with increase in temperature from room to intermediate temperatures followed by rapid decrease at high temperatures. A gradual decrease in ductility to a minimum at intermediate temperatures followed by an increase at high temperatures has been observed. The fracture mode remained transgranular ductile. The steel displayed signatures of dynamic strain ageing at intermediate temperatures and dominance of recovery at high temperatures. No significant difference in the strength and ductility values was observed for varying silicon in the range 0.24-0.60% in P9 steel. P9 steel for wrapper application displayed strength and ductility values comparable to those reported in the literature.

Elevated temperature tensile properties of P9 steel towards ferritic steel wrapper development for sodium cooled fast reactors

International Nuclear Information System (INIS)

Choudhary, B.K.; Mathew, M.D.; Isaac Samuel, E.; Christopher, J.; Jayakumar, T.

2013-01-01

Tensile deformation and fracture behaviour of the three developmental heats of P9 steel for wrapper applications containing varying silicon in the range 0.24–0.60% have been examined in the temperature range 300–873 K. Yield and ultimate tensile strengths in all the three heats exhibited gradual decrease with increase in temperature from room to intermediate temperatures followed by rapid decrease at high temperatures. A gradual decrease in ductility to a minimum at intermediate temperatures followed by an increase at high temperatures has been observed. The fracture mode remained transgranular ductile. The steel displayed signatures of dynamic strain ageing at intermediate temperatures and dominance of recovery at high temperatures. No significant difference in the strength and ductility values was observed for varying silicon in the range 0.24–0.60% in P9 steel. P9 steel for wrapper application displayed strength and ductility values comparable to those reported in the literature

The effect of laser treatment on the wear resistance of steel in corrosive media

International Nuclear Information System (INIS)

Plyatsko, G.V.; Porter, A.I.; Prejs, G.A.; Mojsa, M.I.

1975-01-01

The corrosion mechanical wearing properties of steel 45 treated with a laser beam (H 100 =7800 Mn/sq.m) under friction with nitrated steel 40KhNMA (HV=7000 Mn/sq.m), chrome cast iron Kh15M (hardened and low-temperature tempered, modified), perlite cast iron and bronze are studied. The aqueous buffers with pH=6 and 11 are used as a corrosion active media. In a weakly acid medium the most intensive wearing of steel 40KhNMA is observed at P=8 Mn/sq.m. Its wearing reduces due to increase of pressure to 12 Mn/sq.m. Extent of steel 45 wearing increases with pressure increase from 8 to 12 Mn/sg.m. Friction coefficient of this pair changes by jumps at an increase of normal pressure and its variation range is smaller than that observed in an alkaline medium. The maximum value of friction coefficient is shifted to the higher pressure. The wearing of cast iron Kh15M-steel 45 pair has an alternative pattern. In an alkaline medium the cast iron wearing intensity shows a linear increase with the normal contact pressure but that of the steel changes jumpwise attaining extreme at 8 and 12 Mn/sq.m. In a weak acid medium the intensity of grasping and graphitization at the friction surface of cast iron Kh15M-steel 45 pair is higher than that in the alkaline medium. Experiments demonstrate an effectiveness of the laser beam treatment of steel 45 for its friction in the alkaline medium with nitrated steel 40KhNMA and with hardened low-temperature tempered cast iron 45 under friction contact pressure as high as 8 Mn/sq.m, and in acid medium at 12 and 8 Mn/sq.m respectively. The laser treatment provides high corrosion-mechanical stability of steel 45 and the counterbodies described, as well as the low friction coefficient of these pairs

Welding wires for high-tensile steels

International Nuclear Information System (INIS)

Laz'ko, V.E.; Starova, L.L.; Koval'chuk, V.G.; Maksimovich, T.L.; Labzina, I.E.; Yadrov, V.M.

1993-01-01

Strength of welded joints in arc welding of high-tensile steels of mean and high thickness by welding wires is equal to approximately 1300 MPa in thermohardened state and approximately 600 MPa without heat treatment. Sv-15Kh2NMTsRA-VI (EhK44-VI) -Sv-30Kh2NMTsRA-VI (EkK47-VI) welding wires are suggested for welding of medium-carbon alloyed steels. These wires provide monotonous growth of ultimate strength of weld metal in 1250-1900 MPa range with increase of C content in heat-treated state

Stress corrosion (Astm G30-90 standard) in 08x18H10T stainless steel of nuclear fuel storage pool in WWER reactors

International Nuclear Information System (INIS)

Herrera, V.; Zamora R, L.

1997-01-01

At the water storage of the irradiated nuclear fuel has been an important factor in its management. The actual pools have its walls covered with inoxidable steel and heat exchangers to dissipate the residual heat from fuel. It is essential to control the water purity to eliminate those conditions which aid to the corrosion process in fuel and at related components. The steel used in this research was obtained from an austenitic inoxidizable steel standardized with titanium 08x18H10T (Type 321) similar to one of the two steel coatings used to cover walls and the pools floor. the test consisted in the specimen deformation through an U ply according to the Astm G30-90 standard. The exposition of the deformed specimen it was realized in simulated conditions to the chemical regime used in pools. (Author)

New method for NPP sodium coolant pipeline austenization

International Nuclear Information System (INIS)

Malashonok, V.A.; Rotshtejn, A.V.; Gotshalk, A.L.; Miryushchenko, E.F.

1980-01-01

Heat treatment technology is considered for pipelines intended for the NPP cooling systems employing sodium coolant. Various techniques are discussed which are used for protecting the pipeline internal surfaces against oxidation in the process of heat treatment. It is noted that the austenite formation of welded joints of steel 12Kh18N9 and steel Kh16N11M3 at temperatures of 1050 and 1100 deg C releases welding-induced stresses and reduces a possibility of local damages. Evacuation down to 1 mm Hg appears to be the most rational protective technique. The considered procedure of the pipeline heat treatment has been utilized for mounting the equipment of the BN-600 reactor at the Beloyarskaya NPP. The economic gain resulting from the use of the procedure, owing to decrease in argon consumption and reduction of labour input, makes up 150 000 roubles

Special Features of Induction Annealing of Friction Stir Welded Joints of Medium-Alloy Steels

Science.gov (United States)

Priymak, E. Yu.; Stepanchukova, A. V.; Bashirova, E. V.; Fot, A. P.; Firsova, N. V.

2018-01-01

Welded joints of medium-alloy steels XJY750 and 40KhN2MA are studied in the initial condition and after different variants of annealing. Special features of the phase transformations occurring in the welded steels are determined. Optimum modes of annealing are recommended for the studied welded joints of drill pipes, which provide a high level of mechanical properties including the case of impact loading.

Preoperative chemoradiotherapy followed by local excision in clinical T2N0 rectal cancer

Energy Technology Data Exchange (ETDEWEB)

Shin, Young Seob; Park, Jin Hong; Ahn, Seung Do [Dept. of Radiation Oncology, Asan Medical Center, University of Ulsan College of Medicine, Seoul (Korea, Republic of); and others

2016-09-15

To investigate whether preoperative chemoradiotherapy (PCRT) followed by local excision (LE) is feasible approach in clinical T2N0 rectal cancer patients. Patients who received PCRT and LE because of clinical T2 rectal cancer within 7 cm from anal verge between January 2006 and June 2014 were retrospectively analyzed. LE was performed in case of a good clinical response after PCRT. Patients' characteristics, treatment record, tumor recurrence, and treatment-related complications were reviewed at a median follow-up of 49 months. All patients received transanal excision or transanal minimally invasive surgery. Of 34 patients, 19 patients (55.9%) presented pathologic complete response (pCR). The 3-year local recurrence-free survival and disease free-survival were 100.0% and 97.1%, respectively. There was no recurrence among the patients with pCR. Except for 1 case of grade 4 enterovesical fistula, all other late complications were mild and self-limiting. PCRT followed by an LE might be feasible as an alternative to total mesorectal excision in good responders with clinical T2N0 distal rectal cancer.

Preoperative chemoradiotherapy followed by local excision in clinical T2N0 rectal cancer

International Nuclear Information System (INIS)

Shin, Young Seob; Park, Jin Hong; Ahn, Seung Do

2016-01-01

To investigate whether preoperative chemoradiotherapy (PCRT) followed by local excision (LE) is feasible approach in clinical T2N0 rectal cancer patients. Patients who received PCRT and LE because of clinical T2 rectal cancer within 7 cm from anal verge between January 2006 and June 2014 were retrospectively analyzed. LE was performed in case of a good clinical response after PCRT. Patients' characteristics, treatment record, tumor recurrence, and treatment-related complications were reviewed at a median follow-up of 49 months. All patients received transanal excision or transanal minimally invasive surgery. Of 34 patients, 19 patients (55.9%) presented pathologic complete response (pCR). The 3-year local recurrence-free survival and disease free-survival were 100.0% and 97.1%, respectively. There was no recurrence among the patients with pCR. Except for 1 case of grade 4 enterovesical fistula, all other late complications were mild and self-limiting. PCRT followed by an LE might be feasible as an alternative to total mesorectal excision in good responders with clinical T2N0 distal rectal cancer

Study on TV X-ray system characteristics

International Nuclear Information System (INIS)

Semenov, A.P.; Volkov, A.V.

1978-01-01

The results are presented of comparative investigations into the main characteristics of TV X-ray systems (TXS) and X-ray radiography when X-raying of the 1Kh18N9T steel. The following characteristics are considered: the threshold contrast sensitivity, the sensitivity to revealing standard defects, and the dose rate of X-radiation at the input of the X-ray converter. Practical recommendations are given on the use of TXS in flaw detection of various materials. It is remarked to use introscopes for testing of thick welded products articles, and X-ray vidicon systems for study of low-contrast images (in testing of welds made by point welding, and of thin-wall products)

Application of alternating current for dimensionally electrochemical machining

International Nuclear Information System (INIS)

Kacheev, M.K.; Kovalev, L.M.

1978-01-01

The results of comparative experimental investigations in dimensionally electrochemical machining of 1Kh18N9T steel using alternating and direct currents are presented. The effect of the electrolyte rate in the inter-electrode clearance, electrode voltage and oscillation amplitude of the electrode-tool on the metal output from the electrodes and the relief of the machined surface is studied. It is shown that the a.c. electrochemical machining permits to achieve the greater dimensional accuracy than the d.c. machining when choosing the proper voltage and electrolyte composition. It is connected with the fact that the prevailing part of the metal output is obtained in the impulse-asymmetrical regime when the inter-electrode clearance is minimum

Patterns of failure and overall survival in patients with completely resected T3 N0 M0 non-small cell lung cancer

International Nuclear Information System (INIS)

Gould, Perry M.; Bonner, James A.; Sawyer, Timothy E.; Deschamps, Claude; Lange, Carla M.; Li Hongzhe

1999-01-01

Background: Previous studies of patients with surgically resected non-small cell lung cancer and chest wall invasion have shown conflicting results with respect to prognosis. Whether high-risk subsets of the T3 N0 M0 population exist with respect to patterns of failure and overall survival has been difficult to ascertain, owing to small numbers of patients in most series. Methods and Materials: A retrospective review was performed to determine patterns of failure and overall survival for patients with completely resected T3 N0 M0 non-small cell lung cancer. From 1979 to 1993, 92 evaluable patients underwent complete resection for T3 N0 M0 non-small cell lung cancer. The following potential prognostic factors were recorded from the history: tumor size, location, grade, histology, patient age, use of adjuvant radiation therapy (18 of 92 patients), and type of surgical procedure (chest wall or extrapleural resection). Results: The actuarial 2- and 4-year overall survival rates for the entire cohort were 48% and 35%, respectively. The actuarial local control at 4 years was 94%. Neither the type of surgical procedure performed nor the addition of thoracic radiation therapy impacted local control or overall survival. Conclusion: Patients with completely resected T3 N0 M0 non-small cell lung cancer have similar local control and overall survival irrespective of primary location, type of surgery performed, or use of adjuvant radiation therapy. Additionally, the tumor recurrence rate and overall survival found in this study support the placement of this group of patients in Stage IIB of the 1997 AJCC lung staging classification

Structure and friction properties of cermet and oxide explosion coatings

International Nuclear Information System (INIS)

RGrigorov, A.I.; Semenov, A.P.; Fed'ko, Yu.P.; Shtejn, L.M.

1977-01-01

Conditions have been specified for spraying explosion coatings of cermets over Kh18N10T stainless steel and an aluminum alloy. A mixture of WC and CO powders served as a material for spraying. The method of micro-X-ray spectrum analysis has been used to study the structure of the transition zone between the coating and the substrate and to establish the mechanism responsible for the formation of a cermet layer

A simplified one-pot synthesis of 9-[(3-[18F]Fluoro-1-hydroxy-2-propoxy)methyl]guanine([18F]FHPG) and 9-(4-[18F]Fluoro-3-hydroxymethylbutyl)guanine ([18F]FHBG) for gene therapy

International Nuclear Information System (INIS)

Shiue, Grace G.; Shiue, Chyng-Yann; Lee, Roland L.; MacDonald, Douglas; Hustinx, Roland; Eck, Stephen L.; Alavi, Abass A.

2001-01-01

9-[(3-[ 18 F]Fluoro-1-hydroxy-2-propoxy)methyl]guanine ([ 18 F]FHPG, 2) has been synthesized by nucleophilic substitution of N 2 -(p-anisyldiphenylmethyl)-9-{[1-(p-anisyldiphenylmethoxy)-3 -toluenesulfonyloxy-2-propoxy]methyl}guanine (1) with potassium [ 18 F]fluoride/Kryptofix 2.2.2 followed by deprotection with 1 N HCl and purification with different methods in variable yields. When both the nucleophilic substitution and deprotection were carried out at 90 deg. C and the product was purified by HPLC (method A), the yield of compound 2 was 5-10% and the synthesis time was 90 min from EOB. However, if both the nucleophilic substitution and deprotection were carried out at 120 deg. C and the product was purified by HPLC, the yield of compound 2 decreased to 2%. When compound 2 was synthesized at 90 deg. C and purified by Silica Sep-Pak (method B), the yield increased to 10-15% and the synthesis time was 60 min from EOB. Similarly, 9-(4-[ 18 F]fluoro-3-hydroxymethylbutyl)guanine ([ 18 F]FHBG, 4) was synthesized with method A and method B in 9% and 10-15% yield, respectively, in a synthesis time of 90 and 60 min, respectively, from EOB. Compound 2 was relatively unstable in acidic medium at 120 deg. C while compound 4 was stable under the same condition. Both compound 2 and compound 4 had low lipid/water partition coefficient (0.126±0.022, n=5 and 0.165±0.023, n=5, respectively). Although it contains non-radioactive ganciclovir (∼5-30 μg) as a chemical by-product, compound 2 synthesized by method B has a similar uptake in 9L glioma cells as that synthesized by method A, and is a potential tracer for imaging herpes simplex virus thymidine kinase gene expression in tumors using PET. Similarly, compound 4 synthesized by method B contains ∼10-25 μg of penciclovir as a chemical by-product. Thus, the simplified one pot synthesis (method B) is a useful method for synthesizing both compound 2 and compound 4 in good yield for routine clinical use, and the method is

Phase Transformations of an Fe-0.85 C-17.9 Mn-7.1 Al Austenitic Steel After Quenching and Annealing

Science.gov (United States)

Cheng, Wei-Chun

2014-09-01

Low-density Mn-Al steels could potentially be substitutes for commercial Ni-Cr stainless steels. However, the development of the Mn-Al stainless steels requires knowledge of the phase transformations that occur during the steel making processes. Phase transformations of an Fe-0.85 C-17.9 Mn-7.1 Al (wt.%) austenitic steel, which include spinodal decomposition, precipitation transformations, and cellular transformations, have been studied after quenching and annealing. The results show that spinodal decomposition occurs prior to the precipitation transformation in the steel after quenching and annealing at temperatures below 1023 K and that coherent fine particles of L12-type carbide precipitate homogeneously in the austenite. The cellular transformation occurs during the transformation of high-temperature austenite into lamellae of austenite, ferrite, and kappa carbide at temperatures below 1048 K. During annealing at temperatures below 923 K, the austenite decomposes into lamellar austenite, ferrite, κ-carbide, and M23C6 carbide grains for another cellular transformation. Last, when annealing at temperatures below 873 K, lamellae of ferrite and κ-carbide appear in the austenite.

Fireside corrosion and steamside oxidation of 9-12% Cr martensitic steels exposed for long term testing

DEFF Research Database (Denmark)

Montgomery, Melanie; Jensen, S. A.; Rasmussen, F.

2009-01-01

MoV121 and HCM12 for the 12% Cr steels. The test tubes were welded in as part of the existing final superheaters in actual plants and exposure has been conducted over a ten year period (1994-2005). Compared to the older steel types, T92 and HCM12 utilise tungsten to improve their creep strength. From......To obtain long term corrosion and steam oxidation data for the 9-12%Cr ferritic steels, test tube sections have been exposed in Amager 3 and Avedore 1 coal fired power plants in Denmark (formerly run by ENERGI E2). Thus direct comparisons can be made for T91 and T92 for the 9% Cr steels and X20Cr...... Avedore I testing, T91 and T92 can be compared for exposure times up to similar to 48 000 h exposure. From Amager 3 testing, X20, HCM12 and T92 were tested; T92 has been exposed for up to 31 000 h and X20 and HCM12 have had 84 500 h exposure. Tube sections were removed for various exposure durations...

Characterization of 0.18- μm gate length AlGaN/GaN HEMTs on SiC fabricated using two-step gate recessing

Science.gov (United States)

Yoon, Hyung Sup; Min, Byoung-Gue; Lee, Jong Min; Kang, Dong Min; Ahn, Ho Kyun; Cho, Kyu-Jun; Do, Jae-Won; Shin, Min Jeong; Jung, Hyun-Wook; Kim, Sung Il; Kim, Hae Cheon; Lim, Jong Won

2017-09-01

We fabricated a 0.18- μm gate-length AlGaN/GaN high electron mobility transistor (HEMT) on SiC substrate fabricated by using two-step gate recessing which was composed of inductively coupled plasma (ICP) dry etching with a gas mixture of BCl3/Cl2 and wet chemical etching using the oxygen plasma treatment and HCl-based cleaning. The two-step gate recessing process exhibited an etch depth of 4.5 nm for the AlGaN layer and the clean surface of AlGaN layer at the AlGaN/gate metal contact region for the AlGaN/GaN HEMT structure. The recessed 0.18 μm × 200 μm AlGaN/GaN HEMT devices showed good DC characteristics, having a good Schottky diode ideality factor of 1.25, an extrinsic transconductance ( g m ) of 345 mS/mm, and a threshold voltage ( V th ) of -2.03 V. The recessed HEMT devices exhibited high RF performance, having a cut-off frequency ( f T ) of 48 GHz and a maximum oscillation frequency ( f max ) of 130 GHz. These devices also showed minimum noise figure of 0.83 dB and associated gain of 12.2 dB at 10 GHz.

Corrosion characteristics of the Sm2(Fe0.9Co0.1)17N2.9 magnets stabilized by zinc-coating

International Nuclear Information System (INIS)

Arlot, R.; Machida, K.; Adachi, G.; Rango, P. de; Fruchart, D.

1998-01-01

The effect of powder particle size and of zinc coatings ( 2 (Fe 0.9 Co 0.1 ) 17 N 2.9 magnets has been investigated and compared to those obtained for Sm 2 Fe 17 N 3 and Nd 2 Fe 14 B magnets. Potentiokinetic polarisation behaviour in 0.5 N H 2 SO 4 and in Ringer's solution was studied. It was found that in 0.5 N H 2 SO 4 solution, the corrosion resistance is very weak, whereas in Ringer's solution, Zn coating and epoxy embedding provided a very efficient protection to the magnet. This result is quite unexpected as regarding the very weak amount of Zn (0.73 wt%) and epoxy (2.5-5 wt%) used to stabilize those very reactive ground powders which easily burn in air. Also, we characterized the magnetic properties of severely corroded magnets. (orig.)

Influence of heat treatment on microstructure and properties of GX12CrMoVNbN9-1 cast steel

Directory of Open Access Journals (Sweden)

G. Golański

2010-07-01

Full Text Available The paper presents results of research on the influence of multistage heat treatment on microstructure and properties of high-chromiummartensitic GX12CrMoVNbN9 – 1 (GP91 steel. The material under investigation were samples taken out from a test coupon. Heattreatment of GP91 cast steel was performed at the parameters of temperature and time typical of treatment for multi-ton steel casts. The research has proved that in the as-received condition (as-cast state GP91 cast steel was characterized by a coarse grain, martensitic microstructure which provided the required standard mechanical properties. The heat treatment of GP91 cast steel contributed to obtainment of a fine grain microstructure of high tempered martensite with numerous precipitations of carbides of diverse size. The GP91 cast steel structure received through heat treatment made it possible to obtain high plastic properties, particularly impact strength, maintaining strength properties on the level of the required minimum.

Piezoresistance of Silicon and Strained Si0.9Ge0.1

DEFF Research Database (Denmark)

Richter, Jacob; Hansen, Ole; Larsen, A. Nylandsted

2005-01-01

We present experimentally obtained results of the piezoresistive effect in p-type silicon and strained Si0.9Ge0.1. Today, strained Si1-xGex is used for high speed electronic devices. This paper investigates if this area of use can be expanded to also cover piezoresistive micro electro mechanical...... systems (MEMS) devices. The measurements are performed on microfabricated test chips where resistors are defined in layers grown by molecular beam epitaxy on (0 0 1) silicon substrates. A uniaxial stress along the [1 1 0] direction is applied to the chip, with the use of a four point bending fixture....... The investigation covers materials with doping levels of N-A = 10(18) cm(-3) and NA = 1019 cm(-3), respectively. The results show that the pi(66) piezoresistive coefficient in strained Si0.9Ge0.1 is approximately 30% larger than the comparable pi(44) piezoresistive coefficient in silicon at a doping level of N...

Mechanical and fracture properties at impact loading of selected steels for nuclear power engineering

International Nuclear Information System (INIS)

Buchar, J.; Bilek, Z.

1988-01-01

The possibilities are briefly characterized of experimental research of mechanical and fracture properties of steels used in nuclear power engineering. Attention is paid to plastic deformation and the assessment of fracture formation during impact loading. The results are reported for steels 15Kh2MFA and 10GN2MFA. For steel 15Kh2MFA the effect was also studied of neutron radiation at different temperatures. From the theory developed for non-irradiated material 10GN2MFA, a prediction is made within the original model of the fracture stress value for steel 15Kh2MFA in both non-irradiated and irradiated states. The conclusion is arrived at that the existing methods of assessing steel properties at impact load allow obtaining knowledge of all significant effects during actual stress, this using only small specimens of the materials. (Z.M.). 4 figs., 8 refs

History of the formerly top secret KH-9 Hexagon spy satellite

Science.gov (United States)

Pressel, Phil

2014-12-01

This paper is about the development, design, fabrication and use of the KH-9 Hexagon spy in the sky satellite camera system that was finally declassified by the National Reconnaissance Office on September 17, 2011 twenty five years after the program ended. It was the last film based reconnaissance camera and was known by experts in the field as "the most complicated system ever put up in orbit." It provided important intelligence for the United States government and was the reason that President Nixon was able to sign the SALT treaty, and when President Reagan said "Trust but Verify" it provided the means of verification. Each satellite weighed 30,000 pounds and carried two cameras thereby permitting photographs of the entire landmass of the earth to be taken in stereo. Each camera carried up to 30 miles of film for a total of 60 miles of film. Ultra-complex mechanisms controlled the structurally "wimpy" film that traveled at speeds up to 204 inches per second at the focal plane and was perfectly synchronized to the optical image.

Effect of the damage by radiation on the reference temperature T0 of ferritic steel

International Nuclear Information System (INIS)

Villanueva O, A.

2004-01-01

Presently work studies the effect that produces the irradiation in ferritic steels, on the reference temperature T 0 (intrinsic characteristic of the fracture tenacity in the area of ductile-fragile transition), applying the approach of the Master curve that is based on the norm Astm E-1921. For it it was elaborated a methodology and procedure for test tubes type Charpy according to the standard before mentioned. Due to the ferritic steels are used mainly in pressure vessels to the reactor (RPV) of nuclear power plants; in the samples it was simulated the effect of the damage for irradiation through a thermal treatment that induced the precipitation of the carbides and sulfurs in the limits of grain (one of the modifications suffered in the irradiated materials); it was made a comparison later with material samples in initial state (without thermal treatment), used as witness sample, by means of assays of fracture mechanics, specifically flexion in three points; this way with it to observe the effect of the damage for irradiation in the reference temperature (T 0 ). This temperature (T 0 ) it is a very important parameter in the mechanical property of the material called fracture tenacity; which at the moment gives the rule for the verification of structural integrity of the RPV. As a result of this it was observed an increase in the reference temperature in the material in fragilezed state with respect to the initial state of 31.75 C. They were carried out metallographic analysis and fractographs of the assayed surface finding carbide inclusions and sulfurs that in theory of the Master Curve they are initiators of cracks and of a possible catastrophic flaw of the material. At the moment the Division of Scientific Investigation of the ININ is carrying out activities in the Nucleo electric Central of Laguna Verde (CNLV) related with the program of surveillance of the materials of the vessel of the unit 2, as well as projects of structural integrity financed by the

Residual pathological stage at radical cystectomy significantly impacts outcomes for initial T2N0 bladder cancer.

Science.gov (United States)

Isbarn, Hendrik; Karakiewicz, Pierre I; Shariat, Shahrokh F; Capitanio, Umberto; Palapattu, Ganesh S; Sagalowsky, Arthur I; Lotan, Yair; Schoenberg, Mark P; Amiel, Gilad E; Lerner, Seth P; Sonpavde, Guru

2009-08-01

We hypothesized that in patients with T2N0 stage disease at transurethral bladder tumor resection a lower residual cancer stage (P1N0 or less) at radical cystectomy may correlate with improved outcomes relative to those with residual P2N0 disease. We analyzed 208 patients with T2N0 stage disease at transurethral bladder tumor resection whose tumors were organ confined at radical cystectomy (P2 or lower, pN0). None received perioperative chemotherapy. Kaplan-Meier as well as univariable and multivariable Cox regression models addressed the effect of residual pT stage at radical cystectomy on recurrence and cancer specific mortality rates. Covariates consisted of age, gender, grade, lymphovascular invasion, carcinoma in situ, number of lymph nodes removed and year of surgery. Residual pT stage at radical cystectomy was P0 in 24 (11.5%) patients, Pa in 9 (4.3%), PCIS in 22 (10.6%), P1 in 35 (16.8%) and P2 in 118 (56.7%). Median followup of censored patients was 55.7 months for recurrence and 52.1 months for cancer specific mortality analyses. The 5-year recurrence-free survival rates of patients with P0/Pa/PCIS, P1 and P2 stage disease were 100%, 85% and 75%, respectively. The 5-year cancer specific survival rates for the same cohorts were 100%, 93% and 81%, respectively. On multivariable analysis the effect of residual stage P1 or lower at radical cystectomy achieved independent predictor status for recurrence (adjusted HR 0.20, p = 0.002) and cancer specific mortality (adjusted HR 0.24, p = 0.02). Down staging from initial T2N0 bladder cancer at transurethral bladder tumor resection to lower stage at radical cystectomy significantly reduces recurrence and cancer specific mortality. Further validation of this finding is warranted.

Composition of the spheroidal objects in KhN77TYuR-VD alloy

International Nuclear Information System (INIS)

Kotkis, M.A.; Nabutovskii, L.S.; Ostrov, A.E.; Zil'berman, A.G.

1986-01-01

The authors make an element analysis of the spheroidal objects in KhN77TYuR-VD alloy with the use of the energy dispersion microanalyzer with which the Stereoscan S-180 scanning electron microscope is equipped. Examples of the qualitative element analysis are shown. The results of the investigations show that the composition of the spheroidal inclusions includes nickel, chromium, titanium, iron, and also silicon and sulfur. The information obtained makes it possible to make an assumption on the mechanism of origin of these objects

Calorimetric Investigation of Thermal Stability of 304H Cu (Fe-17.7Cr-9.3Ni-2.95Cu-0.91Mn-0.58Nb-0.24Si-0.1C-0.12N-Wt Pct) Austenitic Stainless Steel

Science.gov (United States)

Tripathy, Haraprasanna; Subramanian, Raju; Hajra, Raj Narayan; Rai, Arun Kumar; Rengachari, Mythili; Saibaba, Saroja; Jayakumar, Tammana

2016-12-01

The sequence of phase instabilities that take place in a Fe-17.7Cr-9.3Ni-0.58Nb-2.95Cu-0.12N (wt pct) austenitic stainless steel (304H Cu grade) as a function of temperature has been investigated using dynamic calorimetry. The results obtained from this investigation are supplemented by Thermocalc-based equilibrium and Scheil-Gulliver nonequilibrium solidification simulation. The following phase transformation sequence is found upon slow cooling from liquid: L → L + γ → L + γ + MX → γ + MX + δ → γ +MX + M23C6 → γ + MX + M23C6 + Cu. Under slow cooling, the solidification follows austenite + ferrite (AF) mode, which is in accordance with Thermocalc prediction and Scheil-Gulliver simulation. However, higher cooling rates result in skeletal δ-ferrite formation, due to increased segregation tendency of Nb and Cr to segregate to interdendritic liquid. The solidification mode is found to depend on combined Nb + Cu content. Experimental estimates of enthalpy change associated with melting and secondary phase precipitation are also obtained. In addition a semi-quantitative study on the dissolution kinetics of M23C6 type carbides has also been investigated. The standard solution treatment at 1413 K (1140 °C) is found to be adequate to dissolve both Cu and M23C6 into γ-austenite; but the complete dissolution of MX type carbonitrides occurs near the melting region.

Microstructure and elevated temperature stability of 9-12% Cr steels

Energy Technology Data Exchange (ETDEWEB)

Dogan, Omer N.; Hawk, Jeffrey A.

2005-02-01

Medium Cr steels have been used in fossil fired power plants for many years because of their excellent high temperature stability and mechanical properties. As the desire to increase the efficiency of power plants continues, the operating temperature (>650C) continues to go up. Currently available low and medium Cr containing steels will not withstand the new operating temperature and must be reassessed in terms of their solid-solution and precipitation strengthening schemes. Three medium Cr steels were developed to investigate high temperature alloy strengthening strategies: 0.08C-(9-12)Cr-1.2Ni-0.7Mo-3.0Cu-3.0Co-0.5Ti. The microstructure of the alloy will be described in the as-cast and thermo-mechanically worked states. In addition, the effect on microstructure from long-term high temperature exposure will also be discussed. Finally, the overall stability of these steels will be compared against currently available power plant steels.

Impact behavior of 9-Cr and 12-Cr ferritic steels after low-temperature irradiation

International Nuclear Information System (INIS)

Klueh, R.L.; Vitek, J.M.; Corwin, W.R.; Alexander, D.J.

1987-01-01

Miniature Charpy impact specimens of 9Cr-1MoVNb and 12Cr-1MoVW steels and these steels with 1 and 2% Ni were irradiated in the High-Flux Isotope Reactor (HFIR) at 50 0 C to displacement damage levels of up to 9 dpa. Nickel was added to study the effect of transmutation helium. Irradiation caused an increase in the ductile-brittle transition temperature (DBTT). The 9Cr-1MoVNb steels, with and without nickel, showed a larger shift than the 12Cr-1MoVW steels, with and without nickel. The results indicated that helium also increased the DBTT. The same steels were previously irradiated at higher temperatures. From the present and past tests, the effect of irradiation temperature on the DBTT behavior can be evaluated. For the 9Cr-1MoVNb steel, there is a continuous decrease in the magnitude of the DBTT increase up to an irradiation temperature of about 400 0 C, after which the shift drops rapidly to zero at about 450 0 C. The DBTT of the 12Cr-1MoVW steel shows a maximum increase at an irradiation temperature of about 400 0 C and less of an increase at either higher or lower irradiation temperatures

Do Cartilage Repair Procedures Prevent Degenerative Meniscus Changes? Longitudinal T1ρ and Morphological Evaluation at 3.0T

Science.gov (United States)

Jungmann, Pia M.; Li, Xiaojuan; Nardo, Lorenzo; Subburaj, Karupppasamy; Lin, Wilson; Ma, C. Benjamin; Majumdar, Sharmila; Link, Thomas M.

2014-01-01

Background Cartilage repair (CR) procedures are widely accepted for treatment of isolated cartilage defects at the knee joint. However, it is not well known whether these procedures prevent degenerative joint disease. Hypothesis/Purpose CR procedures prevent accelerated qualitative and quantitative progression of meniscus degeneration in individuals with focal cartilage defects. Study Design Cohort Study; Level of evidence 2b Methods A total of 94 subjects were studied. CR procedures were performed on 34 patients (n=16 osteochondral transplantation, n=18 microfracture); 34 controls were matched. An additional 13 patients received CR and anterior cruciate ligament (ACL) reconstruction (CR&ACL) and 13 patients received only ACL reconstruction. 3.0T MRI with T1ρ mapping and sagittal fat-saturated intermediate-weighted fast spin echo (FSE) sequences was performed to analyze menisci quantitatively and qualitatively (Whole-Organ Magnetic Resonance Imaging Score, WORMS). CR and CR&ACL patients were examined 4 months (n=34; n=13), 1 (n=21; n=8) and 2 (n=9; n=5) years post CR. Control subjects were scanned at baseline and after 1 and 2 years, ACL patients after 1 and 2 years. Results At baseline, global meniscus T1ρ values were higher in individuals with CR (14.2±0.6ms; P=0.004) and in individuals with CR&ACL (17.1±0.9ms; Pmeniscus above cartilage defects (16.4±1.0ms) and T1ρ of the subgroup of control knees without cartilage defects (12.1±0.8ms; Pmeniscus tears at the overlying meniscus; 10% of CR subjects showed an increase of WORMS meniscus score within the first year, none progressed in the second year. Control subjects with (without) cartilage defects showed meniscus tears in 30% (5%) at baseline; 38% (19%) increased within the first, and 15% (10%) within the second year. Conclusions This study identified more severe meniscus degeneration after CR surgery compared to controls. However, progression of T1ρ values was not observed from 1 to 2 years after surgery

Unit rupture work as a criterion for quantitative estimation of hardenability in steel

International Nuclear Information System (INIS)

Kramarov, M.A.; Orlov, E.D.; Rybakov, A.B.

1980-01-01

Shown is possible utilization of high sensitivity of resistance to fracture of structural steel to the hardenability degree in the course of hardening to find the quantitative estimation of the latter one. Proposed is a criterion kappa, the ratio of the unit rupture work in the case of incomplete hardenability (asub(Tsub(ih))) under investigation, and the analoguc value obtained in the case of complete hardenability Asub(Tsub(Ch)) at the testing temperature corresponding to the critical temperature Tsub(100(M). Confirmed is high criterion sensitivity of the hardened steel structure on the basis of experimental investigation of the 40Kh, 38KhNM and 38KhNMFA steels after isothermal hold-up at different temperatures, corresponding to production of various products of austenite decomposition

Thermal stability and thermal property characterisation of Fe–14.4Cr–15.4Ni–2.4Mo–2.36Mn–0.25Ti–1.02Si–0.042C–0.04P–0.005B (mass%) austenitic stainless steel (Alloy D9I)

Energy Technology Data Exchange (ETDEWEB)

Tripathy, Haraprasanna [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102 (India); Raju, S., E-mail: sraju@igcar.gov.in [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102 (India); Rai, Arun Kumar [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102 (India); Panneerselvam, G. [Chemistry Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102 (India); Jayakumar, T. [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102 (India)

2013-02-15

Highlights: ► High temperature enthalpy, specific heat, lattice thermal expansion of Alloy D9I determined. ► Melting and solidification studied by thermal analysis. ► Integrated modelling by Debye–Grüneisen quasiharmonic formalism. ► Comprehensive thermal property assessment for austenitic stainless steel. -- Abstract: High temperature measurements of enthalpy increment (ΔH{sub T}°) and lattice parameter have been carried out on Alloy D9I by means of drop calorimetry and high temperature X-ray diffraction techniques, respectively. In addition, the thermal stability during heating and cooling from the melting range has been investigated by differential scanning calorimetry. It is found that under near equilibrium cooling conditions (3 K min{sup −1}), Alloy D9I exhibits L → γ austenite → L + γ + δ ferrite → γ + δ → γ solidification mode. However, the phase fraction of δ ferrite and the temperature region of γ + δ two phase domain are found to be small. The on-cooling liquidus and solidus temperatures are found to be 1684 and 1631 ± 5 K, respectively. The latent heat of solidification is found to be in the range, 190–220 J g{sup −1}. The thermal analysis study has revealed that solution treated Alloy D9I exhibits an endothermic dissolution of Ti(C,N) particles at about 1323 ± 2 K, with an associated heat effect of 16–20 J g{sup −1}. The specific heat C{sub p} and coefficient of linear thermal expansion α{sub l} at 298.15 K are estimated to be 486 J kg{sup −1} K{sup −1} and 1.15 × 10{sup −5} K{sup −1}, respectively. The measured temperature dependencies of C{sub p} and α{sub l} for Alloy D9I are in good agreement with the general trend exhibited by many austenitic steels. Further, an empirical linear correlation has been found between the measured temperature dependent molar volume and molar enthalpy values. The measured thermal property data have been modelled through Debye–Grüneisen formalism to obtain an

Band alignment of HfO{sub 2}/In{sub 0.18}Al{sub 0.82}N determined by angle-resolved x-ray photoelectron spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Owen, Man Hon Samuel, E-mail: m.owen.sg@ieee.org, E-mail: yeo@ieee.org; Bhuiyan, Maruf Amin; Yeo, Yee-Chia, E-mail: m.owen.sg@ieee.org, E-mail: yeo@ieee.org [Department of Electrical and Computer Engineering, National University of Singapore, Singapore 119260 (Singapore); Zhang, Zheng; Pan, Ji Sheng [Institute of Materials Research and Engineering, A*STAR (Agency for Science, Technology and Research), 3 Research Link, Singapore 117602 (Singapore); Tok, Eng Soon [Department of Physics, National University of Singapore, Singapore 117551 (Singapore)

2014-07-21

The band-alignment of atomic layer deposited (ALD)-HfO{sub 2}/In{sub 0.18}Al{sub 0.82}N was studied by high resolution angle-resolved X-ray photoelectron spectroscopy measurements. The band bending near the HfO{sub 2}/In{sub 0.18}Al{sub 0.82}N interface was investigated, and the potential variation across the interface was taken into account in the band alignment calculation. It is observed that the binding energies for N 1s and Al 2p in In{sub 0.18}Al{sub 0.82}N decreases and the corresponding extracted valence band offsets increases with increasing θ (i.e., closer to the HfO{sub 2}/In{sub 0.18}Al{sub 0.82}N interface), as a result of an upward energy band bending towards the HfO{sub 2}/In{sub 0.18}Al{sub 0.82}N interface. The resultant valence band offset and the conduction band offset for the ALD-HfO{sub 2}/In{sub 0.18}Al{sub 0.82}N interface calculated was found to be 0.69 eV and 1.01 eV, respectively.

Residual and working stresses in pipe joints in heterogeneous metals, due to common action of welding and service loads

International Nuclear Information System (INIS)

Kiselev, S.N.; Voronin, N.N.; Roshchin, V.V.

1978-01-01

The stresses in the welded joints of cylindrical shells are studied, which are caused by the total effect of the thermal deformation welding cycles, by the preheats connected with the thermal treatment or operation, and by power loads. Studied were the shell joints made of the steels Kh18N10T and St.3, as well as the joints of three shells made of different metals, St.3+18N1aT steel+copper. The schematic diagram showing the residual stresses set up under effect of different factors are presented. The following has been shown by the study: the preheating of the welded joints of the shells made of diverse metals up to the operational temperatures does not result in obviating the residual stresses. If the welded shells are loaded by the internal pressure up to the stresses of (0.8-O.9) sigmasub(T), in certain cases an essential (up to 60-70%) reduction in the residual welding stresses may be obtained. The effectiveness of a variation in the residual stresses is reduced in the joints that have been thermally treated after welding. The working stresses set up in the welded joints of the shells made of different metals under the operational loading may be essentially reduced through initial preheating with the application of a pressure or without it. The preheating temperature and the pressures applied may be chosen so that to create the residual strains and the stresses of inverse sign as compared with the working stresses

Draft genome sequence of Bacillus okhensis Kh10-101T, a halo-alkali tolerant bacterium from Indian saltpan

Directory of Open Access Journals (Sweden)

Pilla Sankara Krishna

2015-12-01

Full Text Available We report the 4.86-Mb draft genome sequence of Bacillus okhensis strain Kh10-101T, a halo-alkali tolerant rod shaped bacterium isolated from a salt pan near port of Okha, India. This bacterium is a potential model to study the molecular response of bacteria to salt as well as alkaline stress, as it thrives under both high salt and high pH conditions. The draft genome consist of 4,865,284 bp with 38.2% G + C, 4952 predicted CDS, 157 tRNAs and 8 rRNAs. Sequence was deposited at DDBJ/EMBL/GenBank under the project accession JRJU00000000.

Corrosion of martensitic steels in flowing 17Li83Pb alloy

International Nuclear Information System (INIS)

Flament, T.; Fauvet, P.; Hocde, B.; Sannier, J.

1988-01-01

Corrosion of three martensitic steels - 1.4914, HT9 and T91 - in the presence of flowing 17Li83Pb is investigated in thermal convection loops Tulip entirely made of 1.4914 steel. Two 3000-hour tests were performed at maximal temperatures of respectively 450 and 475 0 C with a δT of 60 0 C and an alloy velocity of about 0.08 m.s -1 . In both tests, corrosion is characterized by an homogeneous dissolution of the steel without formation of a corrosion layer. Corrosion rate is constant and very temperature dependent: the sound-metal loss of 1.4914 steel is 22 μm. year -1 at 450 0 C and 40 μm.year -1 at 475 0 C. Behaviours of 1.4914 and HT9 steels are very similar whereas T91 steel is about 20% less corroded

Establishing exchange bias below T-N with polycrystalline Ni0.52Co0.48O/Co bilayers

DEFF Research Database (Denmark)

Berkowitz, A.E.; Hansen, Mikkel Fougt; Tang, Y.J.

2005-01-01

Exchange-coupled bilayers of polycrystalline ferromagnetic (FM) Co on antiferromagnetic (AFM) Ni0.52Co0.48O were investigated with emphasis on the issue of establishing an exchange-bias field, H-E, below the AFM ordering temperature, T-N. It was found that field-cooling the bilayers through T-N p...

Theoretical and experimental investigations into rare earth oxides behaviour during out of furnace treatment

International Nuclear Information System (INIS)

Vishkarev, A.F.; Smirnov, B.V.; Krup, Yu.M.

1987-01-01

Theoretical model is developed and technology of metal desulfuration and modification by rear earth metals is tested during out of furnace vacuum treatment, the testing of which has demonstrated its high efficiency. 16KhN3MA steel was melted in 120-t open-hearth furnaces under tapping with treatment by synthetic lime-aluminous slag and subsequent ladle degassing by circulation technique. At the early stage of degassing process cerium oxides together with aluminium were introduced into the vacuum chamber in the quantities of 2.0 and 0.2 kg/t respectively. Two meltings ere performed. Sulfur content in steel reduced from 0.017 and 0.018 up to 0.007 and 0.006%

Relationship between thermal embrittlement and hydrogen cracking in 18Ni(250) maraging steel

International Nuclear Information System (INIS)

Rack, H.J.

1974-01-01

The role of grain boundary precipitate structure on the stress corrosion susceptibility of 18Ni(250) maraging steel was examined. Varying solution treatment procedures were used to achieve either a precipitate-free grain boundary or one containing a high density of Ti(C,N) particles. The introduction of these treatments, although drastically affecting the monotonic fracture toughness, did not significantly alter the stress corrosion threshold in 100 percent relative humidity. These results are shown to be consistent with the previous suggestion that, under open circuit conditions, hydrogen-assisted cracking controls the environmental crack growth behavior of 18Ni maraging steels. (U.S.)

Effect of welding thermal cycles on the structure and properties of simulated heat-affected zone areas in X10CrMoVNb9-1 (T91) steel at a state after 100,000 h of operation

Energy Technology Data Exchange (ETDEWEB)

Łomozik, Mirosław, E-mail: miroslaw.lomozik@is.gliwice.pl [Instytut Spawalnictwa, Testing of Materials Weldability and Welded Constructions Department, 44-100 Gliwice, Bł. Czesława 16-18 (Poland); Hernas, Adam, E-mail: adam.hernas@polsl.pl [Silesian University of Technology, Faculty of Materials Engineering and Metallurgy, 40-019 Katowice, Krasińskiego 8 str. (Poland); Zeman, Marian L., E-mail: marian.zeman@is.gliwice.pl [Instytut Spawalnictwa, Testing of Materials Weldability and Welded Constructions Department, 44-100 Gliwice, Bł. Czesława 16-18 (Poland)

2015-06-18

The article presents results of structural tests (light, scanning electron and scanning transmission electron microscopy) of X10CrMoVNb9-1 (T91) creep-resisting steel after approximately 100,000 h of operation. It was ascertained that the parent metal of T91 steel is characterized by the microstructure of tempered martensite with M{sub 23}C{sub 6} carbide precipitates and few dispersive precipitates of MX-type niobium and vanadium carbonitrides. The most inconvenient change in T91 steel precipitate morphology due to long-term operation is the appearance of the Laves Fe{sub 2}Mo phase which along with M{sub 23}C{sub 6} carbide particles forms elongated blocks and conglomerates on grain boundaries. The article also presents results of tests related to the effect of simulated welding thermal cycles on selected properties of X10CrMoVNb9-1 (T91) grade steel at a state after approximately 100,000 h of operation. The tests involved the determination of the chemical composition of the steel tested as well as impact tests, hardness measurements and microscopic metallographic examination (based on light microscopy) of simulated heat-affected zone (HAZ) areas for a cooling time (t{sub 8/5}) restricted within a range between 3 s and 120 s, with and without heat treatment. The tests revealed that, among other results, hardness values of simulated HAZ areas in X10CrMoVNb9-1 (T91) steel do not guarantee cold crack safety of the steel at the state without additional heat treatment. It was also observed that simulated welding thermal cycles of cooling times t{sub 8/5}=3, 12, 60 and 120 s do not significantly affect the toughness and hardness of simulated HAZ areas of the steel tested.

Study on the process of calibration and deep centring of blanks

International Nuclear Information System (INIS)

Potapov, I.N.; Romantsev, B.A.; Popov, V.A.; Volodin, V.V.; Goncharuk, A.V.

1985-01-01

Process of calibration and deep centring of blanks before broaching is developed and studied. Investigations are performed at a semi-industrial screw rolling mill MISiS-100 T. Blanks made of 40Kh, 60, 50, 45KhN2MFA, 30KhGSNA steels 80, 85, and 90 mm in diameter and 300 mm long were calibrated and centered after heating in a furnace to a depth of 200 mm at shafts and faces with different calibration. 30KhN2MFA steel is chosen for face material; heat treatment is conducted under the following conditions: heating up to 950-1000 deg C and hold-up during 30-35 min with the following cooling in the air. The above experimental investigations reveal that the process of calibration and deep centring accomplished at a three-shaft screw rolling mill is rather stable and provides a high accuracy of centering hollow marking