WorldWideScience

Sample records for steel aisi-304 aplicaciones

  1. Applications of the essay at slow deformation velocity in pipes of stainless steel AISI-304; Aplicaciones del ensayo a velocidad de deformacion lenta en tuberias de acero inoxidable AISI-304

    Energy Technology Data Exchange (ETDEWEB)

    Zamora R, L.; Mora R, T. De la [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

    2004-07-01

    Nowadays is carried out research related with the degradation mechanisms of structures, systems and/or components in the nuclear power plants, since many of the involved processes are those responsible for the dependability of these, of the integrity of the components and of the aspects of safety. The purpose of this work, was to determine the grade of susceptibility to the corrosion of a pipe of Austenitic stainless steel AISI 304, in a solution of Na CI (3.5%) to the temperatures of 60 and 90 C, in two different thermal treatments - 1. - Sensitive 650 C by 4 hours and cooled in water. 2. Solubilized to 1050 C by 1 hour and cooled in water.

  2. Corrosion under stress of AISI 304 steel in thiocyanate solutions

    International Nuclear Information System (INIS)

    Perillo, P.M.; Duffo, G.S.

    1989-01-01

    Corrosion susceptibility under stress of AISI 304 steel sensitized in a sodium thiocyanate solution has been studied and results were compared with those obtained with solutions of thiosulfate and tetrathionate. Sensitized steel type 304 is highly susceptible to corrosion when under intergranular stress (IGSCC) in thiocyanate solutions but the aggressiveness of this anion is less than that of the other sulphur anions studied (thiosulfate and tetrathionate). This work has been partly carried out in the Chemistry Department. (Author) [es

  3. Reassessment of the swelling behavior of AISI 304 stainless steel

    International Nuclear Information System (INIS)

    Garner, F.A.; Porter, D.L.

    1982-03-01

    Published swelling data derived from EBR-II irradiations of AISI 304 and 304L have been reanalyzed in light of insights gained from irradiation of AISI 316 and Fe-15Cr-25Ni. The primary influence of temperature, displacement rate and compositional variations in the 300 series stainless steels lies in the duration of the transient regime of swelling and not in the steady-state or constant swelling rate regime

  4. Corrosion of AISI 304 stainless steel in polluted seawater

    International Nuclear Information System (INIS)

    Brankevich, G.; Guiamet, P.; Videla, H.A.

    1987-01-01

    The sequence of microbiofouling settlement on AISI 304 stain steel samples exposed to polluted harbor sea water of a power cooling water intake is studied. The firts sates of bacterial colonization are followed by means of scanning electron microscopy during two weeks of exposure. The relation between microbiofouling and corrosion is also followed by scanning electron microscopy and evaluated through electrochemical polarization experiments. The results obtained show that microbial colonization and extracellular polimeric substances forming the biofilms have a marked influence on the electrochemical behaviour of stainless steel in sea water. Laboratory experiments using inorganic chloride solutions or artificial sea water show a considerably lesser attack of the metal than those performed 'in situ' with natural sea water. Passivity breadown is highly facilitated when complex biological and inorganic deposits (fouling) have settled on the metal surface. (Author) [pt

  5. Static strain aging type AISI-304 austenitic stainless steel

    International Nuclear Information System (INIS)

    Trindade, M.B.

    1981-03-01

    Static strain aging of type AISI-304 austenitic stainless steel was studied from room temperature up to 623K by conducting tests in which the load was held approximately constant, continuously relaxing and unloaded. The aging times varied between 10s and 100h, using a plastic pre deformation of 9% in most of the cases. The static strain aging of 304 steel furnished an activation energy of 23,800 cal/mol. This implies that vacancies play an important role on the aging process. The curve of the variation of the discontinuous yielding with aging time presented different stages, to which specific mathematical expressions were developed. These facts permited the conclusion that Snoek type mechanisms are responsible for the aging in such conditions. (Author) [pt

  6. Study of discordancy mobility in the AISI 304 steel

    International Nuclear Information System (INIS)

    Lima, L.F.C.P. de; Miranda, P.E.V. de; Monteiro, S.N.

    1987-01-01

    Internal Friction (IF), measurements were carried out in a type AISI 304 austenitic stainless steels at approximately 1HZ of frequency in the temperature interval from 120 to 573K. The IF spectra and the vibration frequency were obtained in samples were submitted to specific heat treatments. The results showed IF spectra with a well defined peak at 260K. The intensity dependes on the amount of plastic deformation previously introduced in the sample. Another broad peak was detected between 300 and 400K. Both peaks could only be detected after plastic deformation in uniaxial tension or torsion. In torsionably deformed samples at liquid nitrogen temperature, 77 K, the IF spectrum is observed only after linear annealing at 400K. This apparently results from a high damping due to a possible phase transformation which occurs around room temperature. The broad peak at higher temperature is sensitive to recovery induced by linear annealings. (Author) [pt

  7. Effect of cold working on nitriding process of AISI 304 and 316 austenitic stainless steel

    International Nuclear Information System (INIS)

    Pereira, Silvio Andre de Lima

    2012-01-01

    The nitriding behavior of AISI 304 and 316 austenitic stainless steel was studied by different cold work degree before nitriding processes. The microstructure, thickness, microhardness and chemical micro-composition were evaluated through optical microscopy, microhardness, scanner electronic microscopy and x ray diffraction techniques. Through them, it was observed that previous plastic deformations do not have influence on layer thickness. However, a nitrided layer thicker can be noticed in the AISI 304 steel. In addition, two different layers can be identified as resulted of the nitriding, composed for austenitic matrix expanded by nitrogen atoms and another thinner immediately below expanded by Carbon atoms. (author)

  8. Spring back evaluation by bending under tension tests in conditions of multiaxial stresses corresponding to deep drawing processes. Application to AISI 304 DDQ stainless steel sheet; Evaluacion del springback mediante ensayos de doblado bajo tension en condiciones de multiaxialidad tipicas de los procesos de embuticion profunda. Aplicacion a chapa de acero inoxidable AISI 304 DDQ

    Energy Technology Data Exchange (ETDEWEB)

    Miguel, V.; Coello, J.; Martinez, A.; Calatayud, A.

    2013-09-01

    In this paper, a methodology has been developed for evaluating the spring back of AISI 304 DDQ stainless steel sheet based on a bending under tension test. The main difference of the methodology herein carried out is that tests are made under the multiaxial stresses state that take place in deep drawing processes. This affects to the level of stress value in the test and to the hardening state of the sheet. Springback evaluation has been done in two different areas. Bending area has been evaluated from elastic recovery ratio defined as the ratio between the bending radius after and before bending. Bending and unbending extreme has been studied from the measured curvature radius in this area and taking into account the geometric equivalence of the test with the drawing cups process. Results found allow to state that drawing ratio or deformation ratio have a negligible influence on the springback into the range of values experimented here. Bending radius has hardly influence as well while bending angle is the most significant variable. The results obtained are compared to those measured in deep-drawn cups, finding a great agreement. (Author)

  9. Comparative study of high temperature oxidation behaviour in AISI 304 and AISI 439 stainless steels

    Directory of Open Access Journals (Sweden)

    Antônio Claret Soares Sabioni

    2003-06-01

    Full Text Available This work deals with a comparison of high temperature oxidation behaviour in AISI 304 austenitic and AISI 439 ferritic stainless steels. The oxidation experiments were performed between 850 and 950 °C, in oxygen and Ar (100 vpm H2. In most cases, it was formed a Cr2O3 protective scale, whose growth kinetics follows a parabolic law. The exception was for the the AISI 304 steel, at 950 °C, in oxygen atmosphere, which forms an iron oxide external layer. The oxidation resistance of the AISI 439 does not depend on the atmosphere. The AISI 304 has the same oxidation resistance in both atmospheres, at 850 °C, but at higher temperatures, its oxidation rate strongly increases in oxygen atmosphere. Concerning the performance of these steels under oxidation, our results show that the AISI 439 steel has higher oxidation resistance in oxidizing atmosphere, above 850 °C, while, in low pO2 atmosphere, the AISI 304 steel has higher oxidation resistance than the AISI 439, in all the temperature range investigated.

  10. Designing of CK45 carbon steel and AISI 304 stainless steel dissimilar welds

    OpenAIRE

    Pouraliakbar,Hesam; Hamedi,Mohsen; Kokabi,Amir Hossein; Nazari,Ali

    2014-01-01

    Gas tungsten arc welding of CK45 and AISI304 stainless steel was performed through preparation of different types of samples using ER308L and ERNi-1 wires. Welded samples were studied by different techniques including optical metallography, scanning electron microscopy equipped with energy dispersive X-ray spectroscopy (SEM-EDS), X-ray diffraction, hardness measurements and impact test. It was observed that in the buttered specimen, the structure of the weld metal was completely austenitic wh...

  11. Surface modifications induced by hydrogen in AISI 304 stainless steel

    International Nuclear Information System (INIS)

    Evangelista, G.E.; Miranda, P.E.V. de

    1983-01-01

    Hydrogen induced surface modifications of type AISI 304 SS were studied by charging the samples in a 1N a 1N H 2 SO 4 electrolyte at room temperature. Current densities were varied from 500 to 4000 A/m 2 and charging times from 2 to 50 hours. Charged specimens were analysed using optical and electron scanning microscopy. Vickers microhardness tests with small load was also performed. Metallographic etching metodologies were developed (in black and white and colored photographies) which permited identification of all phases present. It was shown that delayed cracks appear somewhat curved on austenite and perfectly strainght on martensite, following the intersections of a phase platlets. These are the regions where α' martensite is located. The habit plane of these cracks might belong to (100) sub(γ) or (221) sub(γ) plane families. A new phenomenon termed hydrogen induced softening was observed on type AISI 304 SS at elevated current densities and/or charging times. (Author) [pt

  12. Wear resistance of AISI 304 stainless steel submitted to low temperature plasma carburizing

    Directory of Open Access Journals (Sweden)

    Marcos Antônio Barcelos

    Full Text Available Abstract Despite the AISI 304 stainless steel has high corrosion/oxidation resistance, its tribological properties are poor, being one of the barriers for use in severe wear applications. Thus, there is a wide field for studying technologies that aim to increase the surface hardness and wear resistance of this material. In this work, hardness and wear resistance for AISI 304 stainless steel submitted to the thermochemical treatment by low temperature plasma carburizing (LTPC in a fixed gas mixture composition of 93% H2 and 7% CH4 are presented. Through the evaluation of the carburizing layers, it was possible to observe a substantial improvement in tribological properties after all temperature and time of treatment. This improvement is directly related to the increase of the process variables; among them temperature has a stronger influence on the wear resistance obtained using LTPC process.

  13. Use of Direct Current Resistivity Measurements to Assess AISI 304 Austenitic Stainless Steel Sensitization

    OpenAIRE

    Mesquita, Ramaiany Carneiro; Mecury, José Manoel Rivas; Tanaka, Auro Atsumi; Sousa, Regina Célia de

    2015-01-01

    This paper describes the feasibility of using direct current electrical resistivity measurements to evaluate AISI 304 austenitic stainless steel sensitization. ASTM A262 – Practice A and double loop electrochemical potentiodynamic reactivation (DL-EPR) tests were performed to assess the degree of sensitization (DoS) qualitatively and quantitatively, and electrical resistivity (ER) was measured by the four-point direct-current potential drop method. The results indicate that the DoS incr...

  14. Martensitic Transformation in Ultrafine-Grained Stainless Steel AISI 304L Under Monotonic and Cyclic Loading

    Directory of Open Access Journals (Sweden)

    Heinz Werner Höppel

    2012-02-01

    Full Text Available The monotonic and cyclic deformation behavior of ultrafine-grained metastable austenitic steel AISI 304L, produced by severe plastic deformation, was investigated. Under monotonic loading, the martensitic phase transformation in the ultrafine-grained state is strongly favored. Under cyclic loading, the martensitic transformation behavior is similar to the coarse-grained condition, but the cyclic stress response is three times larger for the ultrafine-grained condition.

  15. Welding of AA1050 aluminum with AISI 304 stainless steel by rotary friction welding process

    OpenAIRE

    Alves, Eder Paduan; Piorino Neto, Francisco; An, Chen Ying

    2010-01-01

    Abstract: The purpose of this work was to assess the development of solid state joints of dissimilar material AA1050 aluminum and AISI 304 stainless steel, which can be used in pipes of tanks of liquid propellants and other components of the Satellite Launch Vehicle. The joints were obtained by rotary friction welding process (RFW), which combines the heat generated from friction between two surfaces and plastic deformation. Tests were conducted with different welding process parameters. The ...

  16. Processing of plane strain compression test results for investigation of AISI-304 stainless steel constitutive behavior

    International Nuclear Information System (INIS)

    Aksenov, Sergey A.; Puzino, Yuriy A.; Bober, Stanislav A.; Kliber, Jiri

    2015-01-01

    The paper is oriented toward the determination of constitutive equation constants by the inverse analysis of plane strain compression test results. The interpretation of such results is complicated by the inhomogeneity of strain rate distribution in the specimen caused by rigid ends, the lateral spreading of a specimen friction and the variation of temperature during the test. The results of plane strain compression tests of AISI-304 stainless steel are presented and significant deviations of temperature are observed at higher strain rates. Finite element simulation was performed to estimate the inhomogeneity of strain rate within the specimen and evaluate the effect of friction on the test results. Constitutive equations of the material were obtained by inverse analysis minimizing the deviations between the measured load values and the ones predicted by numerical simulation. Keywords: PSCT, AISI-304, Gleeble, constitutive equations, hot forming, FEM, inverse analysis.

  17. Stoichiometric titanium dioxide ion implantation in AISI 304 stainless steel for corrosion protection

    Science.gov (United States)

    Hartwig, A.; Decker, M.; Klein, O.; Karl, H.

    2015-12-01

    The aim of this study is to evaluate the applicability of highly chemically inert titanium dioxide synthesized by ion beam implantation for corrosion protection of AISI 304 stainless steel in sodium chloride solution. More specifically, the prevention of galvanic corrosion between carbon-fiber reinforced plastic (CFRP) and AISI 304 was investigated. Corrosion performance of TiO2 implanted AISI 304 - examined for different implantation and annealing parameters - is strongly influenced by implantation fluence. Experimental results show that a fluence of 5 × 1016 cm-2 (Ti+) and 1 × 1017 cm-2 (O+) is sufficient to prevent pitting corrosion significantly, while galvanic corrosion with CFRP can already be noticeably reduced by an implantation fluence of 5 × 1015 cm-2 (Ti+) and 1 × 1016 cm-2 (O+). Surface roughness, implantation energy and annealing at 200 °C and 400 °C show only little influence on the corrosion behavior. TEM analysis indicates the existence of stoichiometric TiO2 inside the steel matrix for medium fluences and the formation of a separated metal oxide layer for high fluences.

  18. Stoichiometric titanium dioxide ion implantation in AISI 304 stainless steel for corrosion protection

    International Nuclear Information System (INIS)

    Hartwig, A.; Decker, M.; Klein, O.; Karl, H.

    2015-01-01

    The aim of this study is to evaluate the applicability of highly chemically inert titanium dioxide synthesized by ion beam implantation for corrosion protection of AISI 304 stainless steel in sodium chloride solution. More specifically, the prevention of galvanic corrosion between carbon-fiber reinforced plastic (CFRP) and AISI 304 was investigated. Corrosion performance of TiO 2 implanted AISI 304 – examined for different implantation and annealing parameters – is strongly influenced by implantation fluence. Experimental results show that a fluence of 5 × 10 16 cm −2 (Ti + ) and 1 × 10 17 cm −2 (O + ) is sufficient to prevent pitting corrosion significantly, while galvanic corrosion with CFRP can already be noticeably reduced by an implantation fluence of 5 × 10 15 cm −2 (Ti + ) and 1 × 10 16 cm −2 (O + ). Surface roughness, implantation energy and annealing at 200 °C and 400 °C show only little influence on the corrosion behavior. TEM analysis indicates the existence of stoichiometric TiO 2 inside the steel matrix for medium fluences and the formation of a separated metal oxide layer for high fluences.

  19. Stoichiometric titanium dioxide ion implantation in AISI 304 stainless steel for corrosion protection

    Energy Technology Data Exchange (ETDEWEB)

    Hartwig, A.; Decker, M.; Klein, O.; Karl, H., E-mail: helmut.karl@physik.uni-augsburg.de

    2015-12-15

    The aim of this study is to evaluate the applicability of highly chemically inert titanium dioxide synthesized by ion beam implantation for corrosion protection of AISI 304 stainless steel in sodium chloride solution. More specifically, the prevention of galvanic corrosion between carbon-fiber reinforced plastic (CFRP) and AISI 304 was investigated. Corrosion performance of TiO{sub 2} implanted AISI 304 – examined for different implantation and annealing parameters – is strongly influenced by implantation fluence. Experimental results show that a fluence of 5 × 10{sup 16} cm{sup −2} (Ti{sup +}) and 1 × 10{sup 17} cm{sup −2} (O{sup +}) is sufficient to prevent pitting corrosion significantly, while galvanic corrosion with CFRP can already be noticeably reduced by an implantation fluence of 5 × 10{sup 15} cm{sup −2} (Ti{sup +}) and 1 × 10{sup 16} cm{sup −2} (O{sup +}). Surface roughness, implantation energy and annealing at 200 °C and 400 °C show only little influence on the corrosion behavior. TEM analysis indicates the existence of stoichiometric TiO{sub 2} inside the steel matrix for medium fluences and the formation of a separated metal oxide layer for high fluences.

  20. Investigating early stages of biocorrosion with XPS: AISI 304 stainless steel exposed to Burkholderia species

    Science.gov (United States)

    Johansson, Leena-Sisko; Saastamoinen, Tuomas

    1999-04-01

    We have investigated the interactions of an exopolymer-producing bacteria, Burkholderia sp. with polished AISI 304 stainless steel substrates using X-ray photoelectron spectroscopy (XPS). Steel coupons were exposed to the pure bacteria culture in a specially designed flowcell for 6 h during which the experiment was monitored in situ with an optical microscope. XPS results verified the formation of biofilm containing extracellular polymer on all the samples exposed to bacteria. Sputter results indicated that some ions needed for metabolic processes were trapped within the biofilm. Changes in the relative Fe concentration and Fe 2p peak shape indicated that also iron had accumulated into the biofilm.

  1. Preparation of high-performance ultrafine-grained AISI 304L stainless steel under high temperature and pressure

    Directory of Open Access Journals (Sweden)

    Peng Wang

    2016-08-01

    Full Text Available Bulk ultra-fine grained (UFG AISI 304L stainless steel with excellent mechanical properties was prepared by a high-temperature and high-pressure (HTHP method using nanocrystalline AISI 304L stainless steel powders obtained from ball milling. Samples were sintered in high-pressure conditions using the highest martensite content of AISI 304L stainless steel powders milled for 25 h. Analyses of phase composition and grain size were accomplished by X-ray diffraction and Rietveld refinement. By comparing the reverse martensite transformation under vacuum and HTHP treat, we consider that pressure can effectively promote the change in the process of transformation. Compared with the solid-solution-treated 304L, the hardness and yield strength of the samples sintered under HTHP are considerably higher. This method of preparation of UFG bulk stainless steel may be widely popularised and used to obtain UFG metallic materials with good comprehensive performance.

  2. Behaviour under fatigue of AISI 304-L stainless steel welded joints

    International Nuclear Information System (INIS)

    Scal, M.W.; Joia, C.J.B.M.; Sousa e Silva, A.S. de

    1979-01-01

    The fatigue behaviour at room temperature of AISI-304-L stainless steel welded joints obtained by two distinct welding methods was studied. The results obtained were compared to those characteristic of the base metal. The welded joint fatigue samples were rectified in order to eliminate the effect of the welded seam geometry. It was concluded that the mechanisms of fatigue crack start in this case is commanded by the austenitic matrix, there being no influence of the delta ferrite rate and distribution present at the melted zone. (Author) [pt

  3. The effects of strain induced martensite on stress corrosion cracking in AISI 304 stainless steel

    International Nuclear Information System (INIS)

    Lee, W. S.; Kwon, S. I.

    1989-01-01

    The effects of strain induced martensite on stress corrosion cracking behavior in AISI 304 stainless steel in boiling 42 wt% MgCl 2 solution were investigated using monotonic SSRT and cyclic SSRT with R=0.1 stress ratio. As the amount of pre-strain increased, the failure time of the specimens in monotonic SSRT test decreased independent of the existence of strain induced martensite. The strain induced martensite seems to promote the crack initiation but to retard the crack propagation during stress corrosion cracking

  4. Fatigue of welded joint in a stainless steel AISI 304 L

    International Nuclear Information System (INIS)

    Kuromoto, N.K.; Guimaraes, A.S.; Miranda, P.E.V. de

    1986-01-01

    The flexion fatigue behavior for the base metal and welded joint of an AISI 304 L stainless steel type, used in the Angra-1 reactor, was determined. An automatic welding process was used with improved procedures in order to assure better welding metallurgy. Fatigue tests samples reinforcements were done to allow the evaluation of metallurgical variables, specially the role played by delta ferrite. The resulting welded joint showed better fatigue life than the base metal. Delta ferrite was found to play an important role on the initiation and propagation processes of the fatigue cracks. (Author) [pt

  5. Effect of cold working and annealing on stress corrosion cracking of AISI 304 stainless steel

    International Nuclear Information System (INIS)

    Yeon, Y.M.; Kwun, S.I.

    1983-01-01

    A study was made of the effects of cold working and annealing on the stress corrosion cracking of AISI 304 stainless steel in boiling 42% MgCl 2 solution. When the 60% or 76% of yield stress was applied, the resistance to SCC showed maximum at 30% of cold work. However, when the same load was applied to the annealed specimens after cold working, the resistance to SCC decreased abruptly at 675degC annealing. The fracture mode changed mode change mixed → intergranular → transgranular as the amount of cold work increased. (Author)

  6. Dependence of corrosion properties of AISI 304L stainless steel on the austenite grain size

    Energy Technology Data Exchange (ETDEWEB)

    Sabooni, Soheil; Rashtchi, Hamed; Eslami, Abdoulmajid; Karimzadeh, Fathallah; Enayati, Mohammad Hossein; Raeissi, Keyvan; Imani, Reihane Faghih [Isfahan Univ. of Technology, Isfahan (Iran, Islamic Republic of). Dept. of Materials Engineering; Ngan, Alfonso Hing Wan [The Univ. of Hong Kong (China). Dept. of Mechanical Engineering

    2017-07-15

    The corrosion resistance of austenitic stainless steels is known to be hampered by the loss of chromium available for passive surface layer formation as a result of chromium carbide precipitation at austenite grain boundaries during annealing treatments. Although high-temperature annealing can promote carbide dissolution leading to better corrosion resistance, grain coarsening also results, which would lead to poorer mechanical properties. Processing methods to achieve both good corrosion resistance and mechanical properties are thus highly desirable for austenitic stainless steels. In the present study, we show that the corrosion resistance of AISI 304L stainless steel can be improved by grain refinement into the ultrafine-grained regime. Specifically, samples with different austenite grain sizes in the range of 0.65-12 μm were studied by potentiodynamic polarization and electrochemical impedance spectroscopy tests in a 3.5 wt.% NaCl solution. All samples showed a typical passive behavior with similar corrosion potential, but the corrosion current density decreased significantly with decreasing grain size. The results show that the sample with the finest grain size had the best corrosion resistance due to a higher resistance of the passive layer to pitting attacks. This study indicates that grain refinement which improves mechanical properties can also significantly improve the corrosion resistance of AISI 304L stainless steel.

  7. Microstructure and mechanical properties of Ti/TiN film coated on AISI 304 stainless steel

    International Nuclear Information System (INIS)

    Park, Ji Yoon; Kim, Kwan Hyu; Choe, Han Cheol

    1999-01-01

    The microstructure and mechanical properties of Ti/TiN film coated on AISI 304 stainless steels have been studied. AISI 304 stainless steels containing 0.1∼1.0 wt% Ti were fabricated by using vacuum furnace and followed by solutionization treatment at 1050 .deg. C for 1hr. The specimens were coated by Ti and TiN with 1 μm and 2 μm thickness by electron-beam PVD method. The microstructure and phase analysis were carried out by using XRD, WDS and SEM. Mechanical properties such as hardness (micro-Vickers) and wear resistance were examined. Coated films showed fine columnar structure and some defects. Surface roughness increased in all specimens after TiN coating. XRD patterns showed that the TiN(111) peak was major in TiN single-layer and the other peaks were very weak, but TiN(220) and TiN(200) peaks were developed in Ti/TiN double-layer. The hardness of the coating film was higher in Ti/TiN double-layer than in TiN single-layer and not affected by the Ti content of substrate. Ti/TiN double-layer showed better wear resistance than TiN single-layer. The observed wear traces were sheared type in all coated specimens

  8. Electrochemical behaviour of iron and AISI 304 stainless steel in simulated acid rain solution

    Energy Technology Data Exchange (ETDEWEB)

    Pilic, Zora; Martinovic, Ivana [Mostar Univ. (Bosnia and Herzegovina). Dept. of Chemistry

    2016-10-15

    The growth mechanism and properties of the oxide films on iron and AISI 304 stainless steel were studied in simulated acid rain (pH 4.5) by means of electrochemical techniques and atomic absorption spectrometry. The layer-pore resistance model was applied to explain a potentiodynamic formation of surface oxides. It was found that the growth of the oxide film on iron takes place by the low-field migration mechanism, while that on the stainless steel takes place by the high-field mechanism. Kinetic parameters were determined. Impedance measurements revealed that Fe surface film has no protective properties at the open circuit potential, while the resistance of stainless steel oxide film is very high. The concentration of the metallic ions released into solution and measured by atomic absorption spectroscopy was in accordance with the results obtained from the electrochemical techniques.

  9. X-Ray diffraction application in studying the nitrogen fixing and aging in stainless steel AISI 304

    International Nuclear Information System (INIS)

    Ramos, L.F.V.

    1973-01-01

    Solid solutions of N in AISI-304 stainless steels were aged to different degrees. The aging was monitored through X-Ray difraction measurement of the lattice parameter 'a'. The increases in 'a', due to the increase of N in solid solution were determined experimentally

  10. Study of the M23C6 precipitation in AISI 304 stainless steel by small angle neutron scattering

    International Nuclear Information System (INIS)

    Boeuf, A.; Caciuffo, R.G.M.; Institut Max von Laue - Paul Langevin, 38 - Grenoble; Ancona Univ.; Melone, S.; Puliti, P.; Rustichelli, F.; Institut Max von Laue - Paul Langevin, 38 - Grenoble; Ancona Univ.; Coppola, R.

    1985-01-01

    The results of some small-angle neutron scattering (SANS) experiments on M 23 C 6 (M=Fe, Cr) carbide precipitation in AISI 304 stainless steel, aged at different temperatures during different times, are presented. The total volume fraction, the total surface of precipitates per unit sample volume and the size distribution functions of the M 23 C 6 carbides were determined. (orig.)

  11. Topological characterization of static strain aging of type AISI 304 austenitic stainless steel

    International Nuclear Information System (INIS)

    Monteiro, S.N.; Miranda, P.E.V. de

    1981-01-01

    Static strain aging of type AISI 304 austenitic stainless steel was studied from room temperature up to 623K by conducting tests in which the load was held approximately constant. The aging times varied between 10s and 100h, using a plastic pre-deformation of 9%. The static strain aging of 304 steel furnished an activation energy of 23.800 cal/mol. This implies that vacancies play an important role on the aging process. The curve of the variation of the discontinuous yielding with aging time presented different stages, to which specific mathematical expressions were developed. These facts permited the conclusion that Snock type mechanisms are responsible for the aging in such conditions. (Author) [pt

  12. Semiconducting properties of oxide and passive films formed on AISI 304 stainless steel and Alloy 600

    Directory of Open Access Journals (Sweden)

    Ferreira M. G. S.

    2002-01-01

    Full Text Available The semiconducting properties of passive films formed on AISI 304 stainless steel and Alloy 600 in borate buffer solution were studied by capacitance (Mott-Schottky approach and photocurrent measurements. Oxide films formed on 304 stainless steel in air at 350 ºC have also been studied. The results obtained show that, in all cases the electronic structure of the films is comparable to that of a p-n heterojunction in which the space charges developed at the metal-film and film-electrolyte interfaces have also to be considered. This is in accordance with analytical results showing that the oxide films are in all cases composed of an inner region rich in chromium oxide and an outer region rich in iron oxide.

  13. Corrosion behaviour of AISI 204Cu and AISI 304 stainless steels in simulated pore solution

    Energy Technology Data Exchange (ETDEWEB)

    Kocijan, Aleksandra [Institute of Metals and Technology, Ljubljana (Slovenia)

    2013-10-15

    The evolution of the passive films on AISI 204Cu and AISI 304 stainless steels in simulated pore solution for steel reinforcements in concrete, and with and without the addition of chloride, was studied using cyclic voltammetry and potentiodynamic measurements. The passive layers were studied at open-circuit potential by means of X-ray photoelectron spectroscopy. The passive films on both materials predominantly contained Cr-oxides, whereas the Fe-species were markedly depleted. Mn-enrichment was also observed. The addition of chloride ions did not have a significant influence on the composition of the passive layers. The surface morphology of the products formed on the surface of both investigated materials at open-circuit potential and at high over-potentials in the presence of chloride was studied using scanning electron microscopy. (orig.)

  14. Fatigue assessment by energy approach during tensile tests on AISI 304 steel

    Directory of Open Access Journals (Sweden)

    A. Risitano

    2017-01-01

    Full Text Available Estimation of the fatigue limit for steel ductile materials using non-destructive methods is a topic of great interest to researchers today. In recent years, the method adopted has implemented infrared sensors to detect the surface temperature and correlate it with the fatigue limit. In previous paper, a new energy approach was proposed to investigate the fatigue limit during tensile test. The numerical procedure proposed by Chrysochoos is adopted to clean infrared images and applied to analyse the surface heat sources during tensile test. AISI 304 specimens with rectangular cross-sections are tested. Moreover fatigue tests at increasing loads were carried out on steel by a stepwise succession, applied to the same specimen, for applying the thermographic method. The predictions of the fatigue limit, obtained by the analysis of the energy evolution during the static tests, were compared with the predictions obtained applying the thermographic method during fatigue tests.

  15. Carburizing plasma in a low temperature austenitic stainless steel AISI 304

    International Nuclear Information System (INIS)

    Mota, W.T.; Ramos, F.D.; Rocha, R.C.; Barcelos, M.V.; Barcelos, M.A.

    2014-01-01

    The industrial use of thermochemical treatment assisted by the cold plasma has been widely employed in recent years, mainly oriented to the excellent results obtained in the surface modification of engineering materials, when compared to more traditional methods. In this work, we studied the plasma carburizing low temperature steel AISI 304 mechanical parts used in construction. The thermochemical treatment was performed at a fixed gas atmosphere 7% CH 4 (g) and 93 % H 2 (g), 350 ° C and times of 1, 3 and 5 hours. Samples being tested for Vickers hardness, abrasive microwear, microstructure evaluation by optical microscopy and SEM and X-ray diffraction. The results show significant improvement in surface hardness, wear resistance and good formation of expanded austenite layer and no identifiers peaks of carbides. The results achieved are due to diffusion/adsorption of carbon present in the gaseous atmosphere to the evaluated samples. (author)

  16. Active flux tungsten inert gas welding of austenitic stainless steel AISI 304

    Directory of Open Access Journals (Sweden)

    D. Klobčar

    2016-10-01

    Full Text Available The paper presents the effects of flux assisted tungsten inert gas (A-TIG welding of 4 (10 mm thick austenitic stainless steel EN X5CrNi1810 (AISI 304 in the butt joint. The sample dimensions were 300 ´ 50 mm, and commercially available active flux QuickTIG was used for testing. In the planned study the influence of welding position and weld groove shape was analysed based on the penetration depth. A comparison of microstructure formation, grain size and ferrit number between TIG welding and A-TIG welding was done. The A-TIG welds were subjected to bending test. A comparative study of TIG and A-TIG welding shows that A-TIG welding increases the weld penetration depth.

  17. Applications of the essay at slow deformation velocity in pipes of stainless steel AISI-304

    International Nuclear Information System (INIS)

    Zamora R, L.; Mora R, T. De la

    2004-01-01

    Nowadays is carried out research related with the degradation mechanisms of structures, systems and/or components in the nuclear power plants, since many of the involved processes are those responsible for the dependability of these, of the integrity of the components and of the aspects of safety. The purpose of this work, was to determine the grade of susceptibility to the corrosion of a pipe of Austenitic stainless steel AISI 304, in a solution of Na CI (3.5%) to the temperatures of 60 and 90 C, in two different thermal treatments - 1. - Sensitive 650 C by 4 hours and cooled in water. 2. Solubilized to 1050 C by 1 hour and cooled in water

  18. Physical characterization of austenitic stainless steels AISI 304 and AISI 348 L*

    International Nuclear Information System (INIS)

    Teodoro, Celso Antonio; Silva, Jose Eduardo Rosa da

    2009-01-01

    The study of radiation damages in metals and metallic alloys used as structural materials in nuclear reactors has a strategic meaning to the nuclear technology because it treats of performance of these materials in conditions that simulate the conditions of work in power reactors. Then it becomes necessary to know the essential physical properties of these materials, properties that are sensitive to the microstructural changes that occurred during the irradiation. The purpose of this work is to characterize, initially, some pre-irradiation properties of the stainless steels AISI 304 and AISI 348 L * , such as mechanical (stress-strain and microhardness) and electrical (resistivity). The AISI 348 L * has been studied for use as fuel cladding material. Both materials will be tested after irradiation in the IEA-R1 core and their properties will be compared with those in the pre-irradiated condition. The morphology of the fractured zones after tensile tests was observed using SEM (scanning electron microscopy). (author)

  19. Surface effects induced by cathodic hydrogenation in type AISI 304 stainless steel

    International Nuclear Information System (INIS)

    Silva, T.C.V.

    1984-08-01

    Cathodic hydrogen charging of type AISI 304 stainless steel modified its austenitic structure, giving rise to the formation of two new martensitic phases and the appearance of cracks, in most cases delayed. As electrolyte a 1 N H 2 S O 4 solution containing As 2 O 3 was employed. The cathodic hydrogenation was carries out at room temperature. The transformed phases were identified with black and white and coloured metallographic techniques, as well as by X-ray diffraction. The effect of cathodic hydrogenation in samples uniaxially tensile tested with constant nominal strain rate was investigated. It was concluded that the number of cracks per unit surface area changes with hydrogenation conditions and that hydrogen should be present for the embrittlement to occur. (author)

  20. Local behavior of an AISI 304 stainless steel submitted to in situ biaxial loading in SEM

    Energy Technology Data Exchange (ETDEWEB)

    Caër, C., E-mail: celia.caer@gmail.com; Pesci, R.

    2017-04-06

    The microstructural response of a coarse grained AISI 304 stainless steel submitted to biaxial tensile loading was investigated using SEM and X-ray diffraction. The specimen geometry was designed to allow for biaxial stress state and incipient crack in the center of the active part under biaxial tensile loading. This complex loading was performed step by step by a micromachine fitting into a SEM chamber. At each loading step FSD pictures and EBSD measurements were carried out to study the microstructural evolution of the alloy, namely grain rotations and misorientations, stress-induced martensite formation and crack propagation. According to their initial orientation, grains are found to behave differently under loading. Approximately 60% of grains are shown to reorient to the [110] Z orientation under biaxial tensile loading, whereas the 40% left undergo high plastic deformation. EBSD and XRD measurements respectively performed under loading and on the post mortem specimen highlighted the formation of about 4% of martensite.

  1. Corrosion behaviour of AISI 304 stainless steel subjected to massive laser shock peening impacts with different pulse energies

    International Nuclear Information System (INIS)

    Lu, J.Z.; Qi, H.; Luo, K.Y.; Luo, M.; Cheng, X.N.

    2014-01-01

    Highlights: •Laser shock peening caused an obvious increase of corrosion resistance of 304 steel. •Corrosion resistance of stainless steel increased with increasing pulse energy. •Mechanism of laser shock peening on corrosion behaviour was also entirely determined. -- Abstract: Effects of massive laser shock peening (LSP) impacts with different pulse energies on ultimate tensile strength (UTS), stress corrosion cracking (SCC) susceptibility, fracture appearance and electrochemical corrosion resistance of AISI 304 stainless steel were investigated by slow strain rate test, potentiodynamic polarisation test and scanning electron microscope observation. The influence mechanism of massive LSP impacts with different pulse energies on corrosion behaviour was also determined. Results showed that massive LSP impacts effectively caused a significant improvement on UTS, SCC resistance, and electrochemical corrosion resistance of AISI 304 stainless steel. Increased pulse energy can also gradually improve its corrosion resistance

  2. OPTIMIZATION OF SURFACE ROUGHNESS OF AISI 304 AUSTENITIC STAINLESS STEEL IN DRY TURNING OPERATION USING TAGUCHI DESIGN METHOD

    Directory of Open Access Journals (Sweden)

    D. PHILIP SELVARAJ

    2010-09-01

    Full Text Available The present work is concentrated with the dry turning of AISI 304 Austenitic Stainless Steel (ASS. This paper presents the influence of cutting parameters like cutting speed, feed rate and depth of cut on the surface roughness of austenitic stainless steel during dry turning. A plan of experiments based on Taguchi’s technique has been used to acquire the data. An orthogonal array, the signal to noise (S/N ratio and the analysis of variance (ANOVA are employed to investigate the cutting characteristics of AISI 304 austenitic stainless steel bars using TiC and TiCN coated tungsten carbide cutting tool. Finally the confirmation tests that have been carried out to compare the predicted values with the experimental values confirm its effectiveness in the analysis of surface roughness.

  3. Influence of delta ferrite on corrosion susceptibility of AISI 304 austenitic stainless steel

    Directory of Open Access Journals (Sweden)

    Lawrence O. Osoba

    2016-12-01

    Full Text Available In the current study, the influence of delta (δ ferrite on the corrosion susceptibility of AISI 304 austenitic stainless steel was evaluated in 1Molar concentration of sulphuric acid (H2SO4 and 1Molar concentration of sodium chloride (NaCl. The study was performed at ambient temperature using electrochemical technique—Tafel plots to evaluate the corrosive tendencies of the austenitic stainless steel sample. The as-received (stainless steel specimen and 60% cold-worked (stainless steel specimens were isothermally annealed at 1,100°C for 2 h and 1 h, respectively, and quenched in water. The results obtained show that the heat-treated specimen and the 60% cold-worked plus heat-treated specimen exhibited higher corrosion susceptibility than the as-received specimen, which invariably contained the highest fraction of δ ferrite particles. The finding shows that the presence of δ ferrite, in which chromium (Cr, the main corrosion inhibitor segregates, does not degrade and or reduces the resistance to aqueous corrosion of the austenitic stainless steel material.

  4. Effects of cold working on the pitting corrosion behavior s of AISI 304 stainless steels

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Kee Min; Kim, Jong Soo; Kim, Young Jun; Kwon, Houk Sang [KAIST, Daejon (Korea, Republic of)

    2015-12-15

    These microstructural changes by cold working can lead improvement of mechanical properties, however from a corrosion resistant point of view, the effects of cold working on the corrosion resistance of stainless steel have been argued. Several studies has been focused on the influence of cold working on the localized corrosion resistance of stainless steels. However, the opinions about the role of cold working on the localized corrosion resistance are highly in consistence. Some studies report that the pitting potential of austenitic stainless steels decreased with cold working level, on the other hands, other studies claimed that the pitting resistance was increased by cold working. Therefore it is necessary to verify how cold working affects pitting corrosion behavior of austenitic stainless steels. In the present work, the influence of cold working on the localized corrosion of AISI 304stainless steel in the neutral chloride solution was studied based on point defect model (PDM). The fraction of deformation-induced martensite was linearly increased with cold rolling level. Through cold rolling, the pitting potential was decreased, the metastable pitting event density was significantly increased and the repassivation potential was decreased. The overall localized corrosion resistance was decreased with cold working, however cold working level increased from 30 % to 50 %, localized corrosion resistance was recovered. The accumulated cation vacancy generates a void at metal/film interface, therefore film breakdown accelerates for cold worked alloys.

  5. Effects of cold working on the pitting corrosion behavior s of AISI 304 stainless steels

    International Nuclear Information System (INIS)

    Jung, Kee Min; Kim, Jong Soo; Kim, Young Jun; Kwon, Houk Sang

    2015-01-01

    These microstructural changes by cold working can lead improvement of mechanical properties, however from a corrosion resistant point of view, the effects of cold working on the corrosion resistance of stainless steel have been argued. Several studies has been focused on the influence of cold working on the localized corrosion resistance of stainless steels. However, the opinions about the role of cold working on the localized corrosion resistance are highly in consistence. Some studies report that the pitting potential of austenitic stainless steels decreased with cold working level, on the other hands, other studies claimed that the pitting resistance was increased by cold working. Therefore it is necessary to verify how cold working affects pitting corrosion behavior of austenitic stainless steels. In the present work, the influence of cold working on the localized corrosion of AISI 304stainless steel in the neutral chloride solution was studied based on point defect model (PDM). The fraction of deformation-induced martensite was linearly increased with cold rolling level. Through cold rolling, the pitting potential was decreased, the metastable pitting event density was significantly increased and the repassivation potential was decreased. The overall localized corrosion resistance was decreased with cold working, however cold working level increased from 30 % to 50 %, localized corrosion resistance was recovered. The accumulated cation vacancy generates a void at metal/film interface, therefore film breakdown accelerates for cold worked alloys

  6. Modifications on the behaviour of AISI 304 stainless steel submitted to creep caused by intermediate treatment of annealing

    International Nuclear Information System (INIS)

    Barreto, L.F.P.; Monteiro, S.N.

    1982-01-01

    Type AISI 304 austenitic stainless steel samples which have been previously creep deformed at 750 0 C, were annealed at 1100 0 C. The effects of this heat treatment in the mechanical behavior of this material when retested in creep were investigated. The results were analysed by taking into account the structural modifications observed and the controlling mechanisms which operate during the deformation and fracture occurring in the creep process. (Author) [pt

  7. Experimental Determination of Temperature During Rotary Friction Welding of AA1050 Aluminum with AISI 304 Stainless Steel

    OpenAIRE

    Alves, Eder Paduan; Piorino Neto, Francisco; An, Chen Ying; Silva, Euclides Castorino da

    2012-01-01

    Abstract: The purpose of this study was the temperature monitoring at bonding interface during the rotary friction welding process of dissimilar materiais: AA1050 aluminum with AISI 304 stainless steel. As it is directly related to the mechanical strenght of the junction, its experimental determination in real time is of fundamental importance for understanding and characterizing the main process steps, and the definition and optimization of parameters. The temperature gradients were obtained...

  8. Facile fabrication of superhydrophobic surfaces from austenitic stainless steel (AISI 304) by chemical etching

    Science.gov (United States)

    Kim, Jae-Hun; Mirzaei, Ali; Kim, Hyoun Woo; Kim, Sang Sub

    2018-05-01

    Stainless steels are among the most common engineering materials and are used extensively in humid areas. Therefore, it is important that these materials must be robust to humidity and corrosion. This paper reports the fabrication of superhydrophobic surfaces from austenitic stainless steel (type AISI 304) using a facile two-step chemical etching method. In the first step, the stainless steel plates were etched in a HF solution, followed by a fluorination process, where they showed a water contact angle (WCA) of 166° and a sliding angle of 5° under the optimal conditions. To further enhance the superhydrophobicity, in the second step, they were dipped in a 0.1 wt.% NaCl solution at 100 °C, where the WCA was increased to 168° and the sliding angle was decreased to ∼2°. The long-term durability of the fabricated superhydrophobic samples for 1 month storage in air and water was investigated. The potential applicability of the fabricated samples was demonstrated by the excellent superhydrophobicity after 1 month. In addition, the self-cleaning properties of the fabricated superhydrophobic surface were also demonstrated. This paper outlines a facile, low-cost and scalable chemical etching method that can be adopted easily for large-scale purposes.

  9. Plasma nitriding process by direct current glow discharge at low temperature increasing the thermal diffusivity of AISI 304 stainless steel

    Energy Technology Data Exchange (ETDEWEB)

    Prandel, L. V.; Somer, A.; Assmann, A.; Camelotti, F.; Costa, G.; Bonardi, C.; Jurelo, A. R.; Rodrigues, J. B.; Cruz, G. K. [Universidade Estadual de Ponta Grossa, Grupo de Espectroscopia Optica e Fotoacustica de Materiais, Departamento de Fisica, Av. Carlos Cavalcanti, 4748, CEP 84030-900, Ponta Grossa, PR (Brazil)

    2013-02-14

    This work reports for the first time on the use of the open photoacoustic cell technique operating at very low frequencies and at room temperature to experimentally determine the thermal diffusivity parameter of commercial AISI304 stainless steel and AISI304 stainless steel nitrided samples. Complementary measurements of X-ray diffraction and scanning electron microscopy were also performed. The results show that in standard AISI 304 stainless steel samples the thermal diffusivity is (4.0 {+-} 0.3) Multiplication-Sign 10{sup -6} m{sup 2}/s. After the nitriding process, the thermal diffusivity increases to the value (7.1 {+-} 0.5) Multiplication-Sign 10{sup -6} m{sup 2}/s. The results are being associated to the diffusion process of nitrogen into the surface of the sample. Carrying out subsequent thermal treatment at 500 Degree-Sign C, the thermal diffusivity increases up to (12.0 {+-} 2) Multiplication-Sign 10{sup -6} m{sup 2}/s. Now the observed growing in the thermal diffusivity must be related to the change in the phases contained in the nitrided layer.

  10. Effects of Nitrogen on the DOS and the Passive Film Breakdown Potential of AISI 304 Stainless Steel

    International Nuclear Information System (INIS)

    Choe, Han Cheol; Kim, Kwan Hyu; Kim, Myung Soo; Lee, Ho Jong

    1992-01-01

    Effects of nitrogen on the degree of sensitization (DOS) and the passive film breakdown potential (Eb) of AISI 304 stainless steel were studied by potentiostat. AISI 304 stainless steel samples containing 0.02 ∼ 0.10wt% nitrogen were sensitized by heat treatment at 650 .deg. C. The DOS was measured using the double-loop reactivation method of the electrochemical potentiodynamic reactivation (EPR) test with the potential scan rate of 150 mV/min in the electrolyte of 0.5 M H 2 SO 4 + 0.01 M KSCN solution at 25 .deg. C. The passive film breakdown potential (Eb) and repassivation potential (Er) were detected by using the cyclic potentiodynamic polarization test (CPPT) in 0.5M HCI solution at 25 .deg. C. In addition, corrosion morphologies were observed by SEM and optical microscope. It was found that nitrogen additions up to 0.1wt% decreased DOS and increased Eb and Er of AISI 304 stainless steel, whereas the increasing sensitization time increased the DOS and decreased Eb and Er. The corrosion morphologies showed severe pits and intergranular attacks in the samples of low nitrogen content and high DOS

  11. A three-dimensional thermal finite element analysis of AISI 304 stainless steel and copper dissimilar weldment

    Science.gov (United States)

    Singh, Gurdeep; Saxena, Ravindra K.; Pandey, Sunil

    2018-04-01

    The aim of this study to developed a 3-D thermal finite element model for dissimilar material welding of AISI-304 stainless steel and copper. Welding of similar material is widely studied using experimental and numerical methods but the problem becomes trivial for the welding of dissimilar materials especially in ferrous and nonferrous materials. Finite element analysis of dissimilar material welding is a cost-effective method for the understanding and analysis of the process. The finite element analysis has been performed to predict the heat affected zone and temperature distribution in AISI-304 stainless steel and copper dissimilar weldment using MSC Marc 2017®. Due to the difference in physical properties of these materials the behavior of heat affected zone and temperature distribution are perceived to be different. To verify the accuracy of the thermal finite element model, the welding process was simulated with butt-welded joints having same dimensions and parameters from Attarha and Far [1]. It is found from the study that the heat affected zone is larger in copper weld pads than in AISI 304 stainless steel due to large difference in thermal conductivity of these two weld pads.

  12. Q-switch Nd:YAG laser welding of AISI 304 stainless steel foils

    Energy Technology Data Exchange (ETDEWEB)

    P' ng, Danny [Laboratory for Lasers, MEMS and Nanotechnology, Department of Mechanical Engineering, Iowa State University, Ames, IA 50011-2161 (United States); Molian, Pal [Laboratory for Lasers, MEMS and Nanotechnology, Department of Mechanical Engineering, Iowa State University, Ames, IA 50011-2161 (United States)], E-mail: molian@iastate.edu

    2008-07-15

    Conventional fusion welding of stainless steel foils (<100 {mu}m thickness) used in computer disk, precision machinery and medical device applications suffer from excessive distortion, formation of discontinuities (pore, void and hot crack), uncontrolled melting (melt-drop through) and poor aesthetics. In this work, a 15 ns pulsed, 400 mJ Nd:YAG laser beam was utilized to overcome these barriers in seam welding of 60 {mu}m thin foil of AISI 304 stainless steel. Transmission electron microscopy was used to characterize the microstructures while hardness and tensile-shear tests were used to evaluate the strengths. Surface roughness was measured using a DekTak profilometer while porosity content was estimated using the light microscope. Results were compared against the data obtained from resistance seam welding. Laser welding, compared to resistance seam welding, required nearly three times less heat input and produced welds having 50% narrower seam, 15% less porosity, 25% stronger and improved surface aesthetics. In addition, there was no evidence of {delta}-ferrite in laser welds, supporting the absence of hot cracking unlike resistance welding.

  13. Corrosion Behavior of Ti/TiN Film Coated on AISI 304 Stainless Steel

    Energy Technology Data Exchange (ETDEWEB)

    Choe, Han Cheol [Kwangyang College, Gwangyang (Korea, Republic of); Park, Ji Yoon; Kim, Kwan Hyu [Chonnam National University, Gwangju (Korea, Republic of)

    2000-06-15

    Effects of the Ti content and the presence of Ti underlayer on the corrosion behaviors of TiN coated AISI 304 stainless steel have been studied. The stainless steel containing 0.1{approx}1.0 wt% Ti were melted with a vacuum furnace and heat treated at 1050 .deg. C for 1hr for solutionization. The specimens were coated with Ti and TiN with thickness of 1 {mu}m and 2 {mu}m respectively by electron-beam physical vapour deposition (EB-PVD) method. The microstructures and phase analysis were conducted by using SEM and WDS. The coated films showed fine columnar structure. The corrosion potential obtained from the anodic polarization curves measured in H{sub 2}SO{sub 4} solution increased in proportion to the Ti content of substrate and was much higher in the specimen coated with Ti underlayer compared to the specimen without Ti underlayer. The potential-time and the current-time curves which were obtained in 0.1M H{sub 2}SO{sub 4} + 0.1M HCI solution showed that both the increase in Ti content and the presence of Ti underlayer increased the potential and decreased the current density resulting in a dense passive film and a suppress of pit formation respectively.

  14. Microstructure and mechanical properties of friction welded AISI 1040/AISI 304L steels before and after electrochemical corrosion

    Energy Technology Data Exchange (ETDEWEB)

    Sarsilmaz, Furkan [Firat Univ., Elazig (Turkey). Dept. of Mechatronics Engineering; Kirik, Ihsan [Batman Univ. (Turkey); Ozdemir, Niyazi [Firat Univ., Elazig (Turkey)

    2018-03-01

    The aim of the present study is to investigate the effect of welding parameters both on the electrochemical corrosion behavior and tensile strength of pre- and post-electrochemical corrosion of friction welded dissimilar steels. The microstructural changes of AISI 1040/AISI 304L friction welded couples and also parent materials were analyzed by using scanning electron microscopy. The electrochemical behaviors of AISI1040/AISI304L joints were comparatively investigated by potentiodynamic polarization curve test and by electrochemical impedance spectra. Moreover, tensile strength experiments were carried out determining the behavior of friction welded joints of pre- and post-electrochemical corrosion and results indicated that the maximum tensile test value of the dissimilar welded pre-electrochemical corrosion was higher than those of post-electrochemical corrosion and was also very close to AISI 1040 parent material value.

  15. Some aspects of thermomechanical fatigue of AISI 304L stainless steel: Part I. creep- fatigue damage

    Science.gov (United States)

    Zauter, R.; Christ, H. J.; Mughrabi, H.

    1994-02-01

    Thermomechanical fatigue (TMF) tests on the austenitic stainless steel AISI 304L have been conducted under “true≓ plastic-strain control in vacuum. This report considers the damage oc-curring during TMF loading. It is shown how the temperature interval and the phasing (in-phase, out-of-phase) determine the mechanical response and the lifetime of the specimens. If creep-fatigue interaction takes place during in-phase cycling, the damage occurs inside the ma-terial, leading to intergranular cracks which reduce the lifetime considerably. Out-of-phase cy-cling inhibits creep-induced damage, and no lifetime reduction occurs, even if the material is exposed periodically to temperatures in the creep regime. A formula is proposed which allows prediction of the failure mode, depending on whether creep-fatigue damage occurs or not. At a given strain rate, the formula is able to estimate the temperature of transition between pure fatigue and creep-fatigue damage.

  16. Parametric optimization during machining of AISI 304 Austenitic Stainless Steel using CVD coated DURATOMIC cutting insert

    Directory of Open Access Journals (Sweden)

    M. Kaladhar

    2012-08-01

    Full Text Available In this work, Taguchi method is applied to determine the optimum process parameters for turning of AISI 304 austenitic stainless steel on CNC lathe. A Chemical vapour deposition (CVD coated cemented carbide cutting insert is used which is produced by DuratomicTM technology of 0.4 and 0.8 mm nose radii. The tests are conducted at four levels of Cutting speed, feed and depth of cut. The influence of these parameters are investigated on the surface roughness and material removal rate (MRR. The Analysis Of Variance (ANOVA is also used to analyze the influence of cutting parameters during machining. The results revealed that cutting speed significantly (46.05% affected the machined surface roughness values followed by nose radius (23.7%. The influence of the depth of cut (61.31% in affecting material removal rate (MRR is significantly large. The cutting speed (20.40% is the next significant factor. Optimal range and optimal level of parameters are also predicted for responses.

  17. Reactive sintering and microstructure development of tungsten carbide-AISI 304 stainless steel cemented carbides

    Energy Technology Data Exchange (ETDEWEB)

    Fernandes, C.M. [Department of Materials and Ceramics Engineering, CICECO, University of Aveiro, 3810-193 Aveiro (Portugal); CEMUC-Mechanical Engineering Department, University of Coimbra, Rua Luís Reis Santos, Pinhal de Marrocos, 3030-788 Coimbra (Portugal); Oliveira, F.J. [Department of Materials and Ceramics Engineering, CICECO, University of Aveiro, 3810-193 Aveiro (Portugal); Senos, A.M.R., E-mail: anamor@ua.pt [Department of Materials and Ceramics Engineering, CICECO, University of Aveiro, 3810-193 Aveiro (Portugal)

    2017-06-01

    Sintering of WC-stainless steel (SS) composites within a typical binder range from 6 up to 15 wt% SS was investigated through constant heating rate dilatometry, in vacuum conditions, complemented by differential thermal analysis and by the study of the high temperature wetting behavior of SS on WC. The densification starts ∼900 °C with a typical densification curve for all compositions, where three distinct regions are discernible: the first one with a slow densification rate, followed by a second region where a sharp increase in the densification rate up to a maximum value dependent on the binder amount is observed and, finally, a third one with a slowdown of the densification rate until the end of the thermal cycle. The attained final density at 1450 °C is dependent on the binder amount, increasing proportionally to its initial content. The final microstructure presents a normal grain size distribution and appreciable amounts of eta-phase, besides the major WC phase and residual iron rich phase. The reactive densification behavior and the role of the liquid phase are interpreted accordingly with structural and kinetic data. - Highlights: • Sintering of WC-AISI304 composites starts ∼900 °C and involves three stages. • Densification is largely dominated by a reactive liquid phase sintering process. • Eta-phase constitutes a transient liquid phase during sintering. • Sintering cycles are dependent on the initial binder content.

  18. Microstructure analysis of AISI 304 stainless steel produced by twin-roll thin strip casting process

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The microstructure of AISI 304 austenite stainless steel fabricated by the thin strip casting process were investigated using optical microscope, scanning electron microscope (SEM), transmission electron microscope (TEM), and X-ray diffraction (XRD).The microstructures of the casting strips show a duplex structure consisting of delta ferrite and austenite. The volume fraction of the delta ferrite is about 9.74vol% at the center and 6.77vol% at the surface of the casting thin strip, in vermicular and band shapes. On account of rapid cooling and solidification in the continuous casting process, many kinds of inclusions and precipitates have been found. Most of the inclusions and precipitates are spherical complex compounds consisting of oxides, such as, SiO2, MnO, Al2O3,Cr2O3,and FeO or their multiplicity oxides of MnO·Al2O3,2FeO·SiO2, and 2MnO·SiO2. Many defects including dislocations and stacking faults have also formed during the rapid cooling and solidification process, which is helpful to improve the mechanical properties of the casting strips.

  19. Low temperature tensile deformation and acoustic emission signal characteristics of AISI 304LN stainless steel

    Energy Technology Data Exchange (ETDEWEB)

    Barat, K.; Bar, H.N. [Material Science and Technology Division, CSIR-National Metallurgical Laboratory, Jamshedpur 831007 (India); Mandal, D. [Material Processing and Technology Division, CSIR-National Metallurgical Laboratory, Jamshedpur 831007 (India); Roy, H., E-mail: himadri9504@gmail.com [NDT and Metallurgy Group, CSIR-Central Mechanical Engineering Research Institute, Durgapur 713209 (India); Sivaprasad, S.; Tarafder, S. [Material Science and Technology Division, CSIR-National Metallurgical Laboratory, Jamshedpur 831007 (India)

    2014-03-01

    This investigation examines low temperature tensile deformation behavior of AISI 304LN stainless steel along with synergistic analysis of acoustic emission signals. The tensile tests are done at a range of temperatures starting from 283 K till 223 K. The fracture surfaces of the broken specimens are investigated using scanning electron microscope. The amount of deformation induced martensite is measured using a feritscope. The obtained results reveal that with decrease in test temperature, both strength and ductility increase. The increase in strength and ductility with decreasing temperature is explained in terms of void morphologies and formation of deformation induced martensite. The rapid increment in strength and ductility at 223 K is associated with the burst of martensitic transformation at that temperature; which has been clarified from acoustic emission signals. An additional initiative has been taken to model the evolution of martensite formation from the observed cumulative emission counts using a non linear logarithmic functional form. The fitted curves from the recorded acoustic emission cumulative count data are found to be better correlated compared to earlier obtained results. However, at 223 K normal non-linear logarithmic fit is not found suitable due to presence of burst type signals at intervals, therefore; piecewise logarithmic function to model acoustic emission bursts is proposed.

  20. The Investigation of Strain-Induced Martensite Reverse Transformation in AISI 304 Austenitic Stainless Steel

    Science.gov (United States)

    Cios, G.; Tokarski, T.; Żywczak, A.; Dziurka, R.; Stępień, M.; Gondek, Ł.; Marciszko, M.; Pawłowski, B.; Wieczerzak, K.; Bała, P.

    2017-10-01

    This paper presents a comprehensive study on the strain-induced martensitic transformation and reversion transformation of the strain-induced martensite in AISI 304 stainless steel using a number of complementary techniques such as dilatometry, calorimetry, magnetometry, and in-situ X-ray diffraction, coupled with high-resolution microstructural transmission Kikuchi diffraction analysis. Tensile deformation was applied at temperatures between room temperature and 213 K (-60 °C) in order to obtain a different volume fraction of strain-induced martensite (up to 70 pct). The volume fraction of the strain-induced martensite, measured by the magnetometric method, was correlated with the total elongation, hardness, and linear thermal expansion coefficient. The thermal expansion coefficient, as well as the hardness of the strain-induced martensitic phase was evaluated. The in-situ thermal treatment experiments showed unusual changes in the kinetics of the reverse transformation (α' → γ). The X-ray diffraction analysis revealed that the reverse transformation may be stress assisted—strains inherited from the martensitic transformation may increase its kinetics at the lower annealing temperature range. More importantly, the transmission Kikuchi diffraction measurements showed that the reverse transformation of the strain-induced martensite proceeds through a displacive, diffusionless mechanism, maintaining the Kurdjumov-Sachs crystallographic relationship between the martensite and the reverted austenite. This finding is in contradiction to the results reported by other researchers for a similar alloy composition.

  1. Biaxial fatigue tests and crack paths for AISI 304L stainless steel

    Directory of Open Access Journals (Sweden)

    V. Chaves

    2014-10-01

    Full Text Available AISI 304L stainless steel specimens have been tested in fatigue. The tests were axial, torsional and in-phase biaxial, all of them under load control and R=-1. The S-N curves were built following the ASTM E739 standard and the method of maximum likelihood proposed by Bettinelli. The fatigue limits of the biaxial tests were represented in axes σ-τ. The elliptical quadrant, appropriate for ductile materials, and the elliptical arc, appropriate for fragile materials, were included in the graph. The experimental values were better fitted with an elliptical quadrant, despite the ratio between the pure torsion and tension fatigue limits, τFL/σFL, is 0.91, close to 1, which is a typical value for fragile materials. The crack direction along the surface has been analyzed by using a microscope, with especial attention to the crack initiation zones. The crack direction during the Stage I has been compared with theoretical models.

  2. Propagation of crevices in stainless steel AISI304L in conditions of hydrogen chemistry (HWC)

    International Nuclear Information System (INIS)

    Diaz S, A.; Fuentes C, P.; Merino C, F.; Castano M, V.

    2006-01-01

    Crevice growth velocities in samples of AISI 304L stainless steel thermally welded and sensitized were obtained by the Rising displacement method or of growing displacement. It was used a recirculation circuit in where the operation conditions of a BWR type reactor were simulated (temperature of 288 C and a pressure of 8 MPa) with the chemistry modified by the addition of hydrogen with and without the addition of impurities of a powerful oxidizer like the Cu ++ ion. CT pre cracked specimens were used and each rehearsal stayed to one constant displacement velocity of 1 x 10 -9 m/s (3.6 μm/hr), making a continuous pursuit of the advance of the crack by the electric potential drop technique. To the end of the rehearsal it was carried out the fractographic analysis of the propagation surfaces. The values of the growth velocities obtained by this methodology went similar to the opposing ones under normal conditions of operation; while the fractographic analysis show the cracks propagation in trans and intergranular ways, evidencing the complexity of the regulator mechanisms of the one IGSCC even under controlled ambient conditions or with mitigation methodologies like the alternative hydrogen chemistry. (Author)

  3. Crack propagation in stainless steel AISI 304L in Hydrogen Chemistry conditions (HWC)

    International Nuclear Information System (INIS)

    Diaz S, A.; Fuentes C, P.; Merino C, F.; Castano M, V.

    2006-01-01

    Velocities of crack growth in samples type CT pre cracking of stainless steel AISI 304l solder and sensitized thermally its were obtained by the Rising Displacement method or of growing displacement. It was used a recirculation circuit that simulates the operation conditions of a BWR type reactor (temperature of 280 C and a pressure of 8 MPa) with the chemistry modified by the addition of hydrogen with and without the addition of impurities of a powerful oxidizer like the Cu + ion. In each essay stayed a displacement velocity was constant of 1x10 -9 m/s, making a continuous pursuit of the advance of the crack by the electric potential drop technique. Contrary to the idea of mitigation of the crack propagation velocity by effect of the addition of the hydrogen in the system, the values of the growth velocities obtained by this methodology went similar to the opposing ones under normal operation conditions. To the finish of the rehearsal one carries out the fractographic analysis of the propagation surfaces, which showed cracks growth in trans and intergranular way, evidencing the complexity of the regulator mechanisms of the IGSCC like in mitigation conditions as the alternative Hydrogen Chemistry. (Author)

  4. Welding of AA1050 aluminum with AISI 304 stainless steel by rotary friction welding process

    Directory of Open Access Journals (Sweden)

    Chen Ying An

    2010-09-01

    Full Text Available The purpose of this work was to assess the development of solid state joints of dissimilar material AA1050 aluminum and AISI 304 stainless steel, which can be used in pipes of tanks of liquid propellants and other components of the Satellite Launch Vehicle. The joints were obtained by rotary friction welding process (RFW, which combines the heat generated from friction between two surfaces and plastic deformation. Tests were conducted with different welding process parameters. The results were analyzed by means of tensile tests, Vickers microhardness, metallographic tests and SEM-EDX. The strength of the joints varied with increasing friction time and the use of different pressure values. Joints were obtained with superior mechanical properties of the AA1050 aluminum, with fracture occurring in the aluminum away from the bonding interface. The analysis by EDX at the interface of the junction showed that interdiffusion occurs between the main chemical components of the materials involved. The RFW proves to be a great method for obtaining joints between dissimilar materials, which is not possible by fusion welding processes.

  5. Action of an aerobic hydrogenotroph bacteria isolated from ultrapure water systems on AISI 304 stainless steel

    Energy Technology Data Exchange (ETDEWEB)

    Gales, Gregoire [DTN/SMTM/LMTE, CEA Cadarache, F-13108 Saint-Paul-lez-Durance (France)]|[DSV/DEVM/LEMIR, UMR 6191 CNRS-CEA-Universite Aix-Marseille II, CEA Cadarache, F- 13108 Saint-Paul-lez-Durance (France); Roy, Marc; Feron, Damien [DEN/DPC/SCCME/LECA, Bat 458, CEA Saclay F- 91191 Gif sur Yvette (France); Libert, Marie-Francoise; Sellier, Regine [DTN/SMTM/LMTE, CEA Cadarache, F-13108 Saint-Paul-lez-Durance (France); Cournac, Laurent [DSV/DEVM/LEP, UMR 6191 CNRS-CEA-Universite Aix-Marseille II, CEA Cadarache, F- 13108 Saint-Paul-lez-Durance (France); Heulin, Thierry [DSV/DEVM/LEMIR, UMR 6191 CNRS-CEA-Universite Aix-Marseille II, CEA Cadarache, F- 13108 Saint-Paul-lez-Durance (France)

    2004-07-01

    Several microbial studies have been recently performed in nuclear power stations. These studies concerned essentially the formation of bio-films on submerged metal coupons. Heterotrophic micro-organisms have been found in bulk water of nuclear fuel storage basins but the in situ nutrient sources for bacterial development in such highly oligo-trophic water was unknown. In nuclear environments, radiations lead to the production of molecular hydrogen, hydrogen peroxide and some radicals (OH, O{sub 2}{sup -}) by radiolysis of water or embedding matrices. Bacterial oxidation of molecular H{sub 2} commonly occurs in nature, as molecular hydrogen represents a high-energy reductant. We investigated the microbiology of a ultra-pure water basin containing irradiating waste. The initial aim of this study was to determine if autotrophic bacterial growth was possible in this basin. A major bacteria was isolated (Ralstonia sp. GGLH002) which was able to grow autotrophically with hydrogen as the electron donor and oxygen as the electron acceptor, and heterotrophically with organic nutrients. Its hydrogenase activity has been characterized. We focused then our study on the effects of this strain on 304L AISI stainless steel depending on the nutrient source used for bacterial development, e.g hydrogen or organics. In conclusion, the mechanism of passivation enhanced by Ralstonia sp. GGLH002 on AISI 304L SS still remains unknown. Several techniques could give substantial information, including XPS and polarization curves. It seems for the moment that the major bacteria inhabiting an oxic environment containing hydrogen due to radiolysis is not aggressive to stainless steel in conditions near from its environment. Further investigations are needed to test this hypothesis, including a study of the molecular diversity of the bacteria using culture-independent techniques, as cultivatable bacterial populations represent in general only a fraction of the total bacteria. (authors)

  6. Action of an aerobic hydrogenotroph bacteria isolated from ultrapure water systems on AISI 304 stainless steel

    International Nuclear Information System (INIS)

    Gales, Gregoire; Roy, Marc; Feron, Damien; Libert, Marie-Francoise; Sellier, Regine; Cournac, Laurent; Heulin, Thierry

    2004-01-01

    Several microbial studies have been recently performed in nuclear power stations. These studies concerned essentially the formation of bio-films on submerged metal coupons. Heterotrophic micro-organisms have been found in bulk water of nuclear fuel storage basins but the in situ nutrient sources for bacterial development in such highly oligo-trophic water was unknown. In nuclear environments, radiations lead to the production of molecular hydrogen, hydrogen peroxide and some radicals (OH, O 2 - ) by radiolysis of water or embedding matrices. Bacterial oxidation of molecular H 2 commonly occurs in nature, as molecular hydrogen represents a high-energy reductant. We investigated the microbiology of a ultra-pure water basin containing irradiating waste. The initial aim of this study was to determine if autotrophic bacterial growth was possible in this basin. A major bacteria was isolated (Ralstonia sp. GGLH002) which was able to grow autotrophically with hydrogen as the electron donor and oxygen as the electron acceptor, and heterotrophically with organic nutrients. Its hydrogenase activity has been characterized. We focused then our study on the effects of this strain on 304L AISI stainless steel depending on the nutrient source used for bacterial development, e.g hydrogen or organics. In conclusion, the mechanism of passivation enhanced by Ralstonia sp. GGLH002 on AISI 304L SS still remains unknown. Several techniques could give substantial information, including XPS and polarization curves. It seems for the moment that the major bacteria inhabiting an oxic environment containing hydrogen due to radiolysis is not aggressive to stainless steel in conditions near from its environment. Further investigations are needed to test this hypothesis, including a study of the molecular diversity of the bacteria using culture-independent techniques, as cultivatable bacterial populations represent in general only a fraction of the total bacteria. (authors)

  7. Investigation of residual stress in laser welding between carbon steel AISI 1010 and stainless AISI 304

    International Nuclear Information System (INIS)

    Mirim, Denilson de Camargo

    2011-01-01

    The dissimilar materials union has the residual stress formation as one of the most critical problems, which occurs mainly because these materials have both different thermal expansion coefficients and thermal conductivities. In this study, it was investigated the laser welding technique between steels, AISI 1010 and AISI 304. The materials were joined by butt autogenous welding with a continuous Nd:YAG laser. The main objective was to identify the welding parameters influence by the residual stresses analysis in the heat affected zone (HAZ). It was executed a factorial design with three-factor at two levels with a replica, which were varied power, welding speed and focal position of the laser beam. Residual stress measurements by the diffraction of X-rays were performed on the sample surface, to study their variation as a function of the parameters investigated. The blind hole method was also used to evaluate the residual stress along the samples depth, up to depth of 1mm. Besides residual stress measurement, weld seams were evaluated by optical and scanned electron microscopy, which were aimed to determine the weld geometry and changes in the microstructure. It was also made Vickers hardness measurements to evaluate the extent of HAZ. To evaluate the mechanical properties of the union were performed tensile and fatigue test. The MINITAB 15 software was used to analyze the residual stresses obtained by the blind hole method at different depths of the HAZ. It was also used statistical regression based on both the influences different and the combination of this input factors, in the residual stress of union. The results indicate that the models can satisfactorily predict the responses and provide users a guide to better define the welding parameters. (author)

  8. High temperature oxidation behavior of austenitic stainless steel AISI 304 in steam of nanofluids contain nanoparticle ZrO2

    International Nuclear Information System (INIS)

    Prajitno, Djoko Hadi; Syarif, Dani Gustaman

    2014-01-01

    The objective of this study is to evaluate high temperature oxidation behavior of austenitic stainless steel SS 304 in steam of nanofluids contain nanoparticle ZrO 2 . The oxidation was performed at high temperatures ranging from 600 to 800°C. The oxidation time was 60 minutes. After oxidation the surface of the samples was analyzed by different methods including, optical microscope, scanning electron microscope (SEM) and X-ray diffraction (XRD). X-ray diffraction examination show that the oxide scale formed during oxidation of stainless steel AISI 304 alloys is dominated by iron oxide, Fe 2 O 3 . Minor element such as Cr 2 O 3 is also appeared in the diffraction pattern. Characterization by optical microscope showed that cross section microstructure of stainless steel changed after oxidized with the oxide scale on the surface stainless steels. SEM and x-ray diffraction examination show that the oxide of ZrO 2 appeared on the surface of stainless steel. Kinetic rate of oxidation of austenite stainless steel AISI 304 showed that increasing oxidation temperature and time will increase oxidation rate

  9. High temperature oxidation behavior of austenitic stainless steel AISI 304 in steam of nanofluids contain nanoparticle ZrO2

    Energy Technology Data Exchange (ETDEWEB)

    Prajitno, Djoko Hadi, E-mail: djokohp@batan.go.id; Syarif, Dani Gustaman, E-mail: djokohp@batan.go.id [Research Center for Nuclear Materials and Radiometry, Jl. Tamansari 71, Bandung 40132 (Indonesia)

    2014-03-24

    The objective of this study is to evaluate high temperature oxidation behavior of austenitic stainless steel SS 304 in steam of nanofluids contain nanoparticle ZrO{sub 2}. The oxidation was performed at high temperatures ranging from 600 to 800°C. The oxidation time was 60 minutes. After oxidation the surface of the samples was analyzed by different methods including, optical microscope, scanning electron microscope (SEM) and X-ray diffraction (XRD). X-ray diffraction examination show that the oxide scale formed during oxidation of stainless steel AISI 304 alloys is dominated by iron oxide, Fe{sub 2}O{sub 3}. Minor element such as Cr{sub 2}O{sub 3} is also appeared in the diffraction pattern. Characterization by optical microscope showed that cross section microstructure of stainless steel changed after oxidized with the oxide scale on the surface stainless steels. SEM and x-ray diffraction examination show that the oxide of ZrO{sub 2} appeared on the surface of stainless steel. Kinetic rate of oxidation of austenite stainless steel AISI 304 showed that increasing oxidation temperature and time will increase oxidation rate.

  10. Sliding properties of coevaporated and nitrogen-implanted Pt50Ti50 films on AISI 304 stainless steel

    International Nuclear Information System (INIS)

    Zheng, L.R.; Hung, L.S.; Mayer, J.W.

    1988-01-01

    Thin Pt 50 Ti 50 films were deposited on a AISI 304 stainless steel substrate by co-evaporation. Dry sliding tests and wear track measurements revealed some improvement in sliding properties compared with the bare substrate. Implantation of the coated substrate with xenon ions did not produce any further improvement in friction and wear but a dramatic improvement resulted from nitrogen ion implantation. This was accompanied by a change in microstructure arising from an amorphous to crystalline phase transformation in the alloy film. (U.K.)

  11. Electrochemical Study of Welded AISI 304 and 904L Stainless Steel in Seawater in View of Corrosion

    Directory of Open Access Journals (Sweden)

    Richárd Székely

    2010-10-01

    Full Text Available This is a comparative study of the corrosion behaviour of welds in AISI 304 and AISI 904L stainless steels carried out in seawater model solution in the temperature range 5-35°C and the standard of corrosion testing of welds was followed. The corrosion rate and corrosion attack characteristics were determined for welds of the examined steels with several type of treatment. The aim of this work was to compare the steels based on their resistance against the corrosion in terms of pitting potential (Epit and repassivation potential (Erepass. Seawater is an electrochemically aggressive medium, which can initiate localised corrosion in welded stainless steels. Different electrochemical and testing methods were used, including cyclic voltammetry, chronopotentiometry, electrochemical impedance spectroscopy (EIS, pH measuring and penetration tests.

  12. Effect of temperature on the level of corrosion caused by heavy petroleum on AISI 304 and AISI 444 stainless steel

    Directory of Open Access Journals (Sweden)

    João Paulo Sampaio Eufrásio Machado

    2006-06-01

    Full Text Available This work presents a study on the influence of national heavy petroleum in the corrosion of the AISI 444 and AISI 304 stainless steels in simulated refining operation conditions. The petroleum was first characterized through physicochemical analysis (density, fluidity point, viscosity, sulfur concentration. In an attempt to understand the corrosion effect of temperature and of the type of heating the referred types of steel thermal treatments were carried out at three levels of temperature (200, 300 and 400 °C. The procedure was done in conditions close to those in the distillation column. Heat was gradually increased from room temperature, and directly heated to working temperature. Each treatment took 4 hours to be completed. Scanning electronic microscopy (SEM and the analysis of X rays dispersive energy (EDX were used after the trials to characterize the samples. The results show that treatment temperature, as well as the type of heating, has distinct influences on each type of steel.

  13. Estimation of Fatigue Life of Laser Welded AISI304 Stainless Steel T-Joint Based on Experiments and Recommendations in Design Codes

    DEFF Research Database (Denmark)

    Lambertsen, Søren Heide; Damkilde, Lars; Kristensen, Anders Schmidt

    2013-01-01

    In this paper the fatigue behavior of laser welded T-joints of stainless steel AISI304 is investigated experimentally. In the fatigue experiments 36 specimens with a sheet thickness of 1 mm are exposed to one-dimensional cyclic loading. Three different types of specimens are adopted. Three groups...

  14. Small angle neutron scattering study of the damage induced by creep deformation in AISI 304 stainless steel

    International Nuclear Information System (INIS)

    Boeuf, A.; Coppola, R.; Matera, R.; Rustichelli, F.; Zambonardi, F.; Puliti, P.; Melone, S.

    1982-01-01

    In the austenitic stainless steels, a class of materials largely used in the nuclear power plants, creep induces essentially two new microstructural effects: the nucleation and growth of grain boundary cavities and the precipitation of carbides. Carbides precipitate as a consequence of pure thermal treatment, whereas for the occurrence of voids the presence of stress is necessary. It should be noted however, that the kinetics of precipitation and even the precipitate crystal structure are changed by the introduction of dislocations due to straining during creep. The aim of the present study is a quantitative characterization of the creep damage occurring in a stainless steel of the type X 6 CrNi 8 11 (AISI 304). The experimental techniques used are optical and electron microscopy, microprobe analysis and small angle neutron scattering. This latter technique is described in more detail

  15. The effect of plasma arc process parameters on the properties of dissimilar AISI 1040/AISI 304 steel plate welds

    Energy Technology Data Exchange (ETDEWEB)

    Kilic, Musa; Kirik, Ihsan; Orhan, Nuri [Firat Univ., Elazig (Turkey); Celik, Ferkan [Science Industry and Technology Ministry of Turkey (Turkey)

    2012-11-01

    In this study, 10 mm thick AISI 1040 and AISI 304 steel plates were welded in the butt position without pretreatment by plasma transferred arc (PTA) welding technique. Therefore, mechanical behaviour, microstructure, penetration depth and length were investigated. After welding, microstructural changes in the interface regions of the welded specimens were examined by scanning electron microscopy (SEM) and energy dispersive spectrometry (EDS). Micro-hardness as well as V-notch Charpy tests were performed to determine the mechanical properties of the welds. The influence of the welding parameters on the dimension and shape of the joints has been found out. From the results, it was derived that with the parameters used, a partly keyhole weld bead formed with a penetration depth of 10 mm and a width of 11 mm in butt position. (orig.)

  16. Application of Deep Cryogenic Treatment to Uncoated Tungsten Carbide Inserts in the Turning of AISI 304 Stainless Steel

    Science.gov (United States)

    Özbek, Nursel Altan; Çİçek, Adem; Gülesİn, Mahmut; Özbek, Onur

    2016-12-01

    This study investigated the effects of deep cryogenic treatment (DCT) on the wear performance of uncoated tungsten carbide inserts. AISI 304 austenitic stainless steel, widely used in industry, was selected as the workpiece material. Cutting experiments showed that the amount of wear significantly increased with increasing cutting speed. In addition, it was found that DCT contributed to the wear resistance of the turning inserts. The treated turning inserts were less worn by 48 and 38 pct in terms of crater wear and notch wear, respectively, whereas they exhibited up to 18 pct superior wear performance in terms of flank wear. This was attributed to the precipitation of new and finer η-carbides and their homogeneous distribution in the microstructure of the tungsten carbide material after deep cryogenic treatment. Analyses via image processing, hardness measurements, and SEM observations confirmed these findings.

  17. Experimental Determination of Temperature During Rotary Friction Welding of AA1050 Aluminum with AISI 304 Stainless Steel

    Directory of Open Access Journals (Sweden)

    Eder Paduan Alves

    2012-03-01

    Full Text Available The purpose of this study was the temperature monitoring at bonding interface during the rotary friction welding process of dissimilar materials: AA1050 aluminum with AISI 304 stainless steel. As it is directly related to the mechanical strenght of the junction, its experimental determination in real time is of fundamental importance for understanding and characterizing the main process steps, and the definition and optimization of parameters. The temperature gradients were obtained using a system called Thermocouple Data-Logger, which allowed monitoring and recording data in real-time operation. In the graph temperature versus time obtained, the heating rates, cooling were analyzed, and the maximum temperature was determined that occurred during welding, and characterized every phases of the process. The efficiency of this system demonstrated by experimental tests and the knowledge of the temperature at the bonding interface open new lines of research to understand the process of friction welding.

  18. Investigation on AISI 304 austenitic stainless steel to AISI 4140 low alloy steel dissimilar joints by gas tungsten arc, electron beam and friction welding

    International Nuclear Information System (INIS)

    Arivazhagan, N.; Singh, Surendra; Prakash, Satya; Reddy, G.M.

    2011-01-01

    Research highlights: → Beneficial effects of FRW, GTAW and EBW joints of dissimilar AISI 304 and AISI 4140 materials. → Comparative study of FRW, GTAW and EBW joints on mechanical properties. → SEM/EDAX, XRD analysis on dissimilar AISI 304 and AISI 4140 materials. -- Abstract: This paper presents the investigations carried out to study the microstructure and mechanical properties of AISI 304 stainless steel and AISI 4140 low alloy steel joints by Gas Tungsten Arc Welding (GTAW), Electron Beam Welding (EBW) and Friction Welding (FRW). For each of the weldments, detailed analysis was conducted on the phase composition, microstructure characteristics and mechanical properties. The results of the analysis shows that the joint made by EBW has the highest tensile strength (681 MPa) than the joint made by GTAW (635 Mpa) and FRW (494 Mpa). From the fractographs, it could be observed that the ductility of the EBW and GTA weldment were higher with an elongation of 32% and 25% respectively when compared with friction weldment (19%). Moreover, the impact strength of weldment made by GTAW is higher compared to EBW and FRW.

  19. Influence of ferritic phase on the localized corrosion in the AISI 304 type austenitic stainless steel

    International Nuclear Information System (INIS)

    Lombardi, C.C.M.; Ramanathan, L.V.

    1994-01-01

    The influence of adding up to 4.7 wt% Si to AISI 304 on the pitting corrosion resistance and intergranular corrosion resistance has been studied. The alloys were prepared by melting in a vacuum induction furnace and annealed at 1200 0 C for 1 hour followed by quenching. Prolonged immersion tests in Fe C L 3 and anodic polarization measurements in 3.5% NaCl revealed that with increasing Si the tendency of the alloy to pit decreased and the pitting potential increased. The susceptibility to intergranular corrosion as determined through Huey tests also decreased with Si content. The overall influence of Si in the alloy on the corrosion behaviour is considered to be due to incorporation of Si in the surface film and consequent improvement in adhesion as well as reduction in detects within the film. (author). 7 refs, 4 figs, 6 tabs

  20. Cladding of aluminum on AISI 304L stainless steel by cold roll bonding: Mechanism, microstructure, and mechanical properties

    Energy Technology Data Exchange (ETDEWEB)

    Akramifard, H.R., E-mail: akrami.1367@ut.ac.ir [School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, P.O. Box 11155-4563, Tehran (Iran, Islamic Republic of); Mirzadeh, H., E-mail: hmirzadeh@ut.ac.ir [School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, P.O. Box 11155-4563, Tehran (Iran, Islamic Republic of); Advanced Metalforming and Thermomechanical Processing Laboratory, School of Metallurgy and Materials Engineering, University of Tehran, Tehran (Iran, Islamic Republic of); Parsa, M.H., E-mail: mhparsa@ut.ac.ir [School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, P.O. Box 11155-4563, Tehran (Iran, Islamic Republic of); Center of Excellence for High Performance Materials, School of Metallurgy and Materials Engineering, University of Tehran, Tehran (Iran, Islamic Republic of); Advanced Metalforming and Thermomechanical Processing Laboratory, School of Metallurgy and Materials Engineering, University of Tehran, Tehran (Iran, Islamic Republic of)

    2014-09-08

    The AA1050 aluminum alloy and AISI 304L stainless steel sheets were stacked together to fabricate Al/304L/Al clad sheet composites by the cold roll bonding process, which was performed at temperatures of ∼100 and 23 °C to produce austenitic and austenitic–martensitic microstructures in the AISI 304L counterpart, respectively. The peel test results showed that the threshold reduction required to make a suitable bond at room temperature is below 10%, which is significantly lower than the required reduction for cold roll bonding of Al sheets. The tearing of the Al sheet during the peel test signified that the bond strength of the roll bonded sheets by only 38% reduction has reached the strength of Al, which is a key advantage of the developed sheets. The extrusion of Al through the surface cracks and settling inside the 304L surface valleys due to strong affinity between Al and Fe was found to be the bonding mechanism. Subsequently, the interface and tensile behaviors of three-layered clad sheets after soaking at 200–600 °C for 1 h were investigated to characterize the effect of annealing treatment on the formation and thickening of intermetallic compound layer and the resultant mechanical properties. Field emission scanning electron microscopy, X-ray diffraction, and optical microscopy techniques revealed that an intermediate layer composed mainly of Al{sub 13}Fe{sub 4}, FeC and Al{sub 8}SiC{sub 7} forms during annealing at 500–600 °C. A significant drop in tensile stress–strain curves after the maximum point (UTS) was correlated to the interface debonding. It was found that the formation of intermediate layer by post heat treatment deteriorates the bond quality and encourages the debonding process. Moreover, the existence of strain-induced martensite in clad sheets was found to play a key role in the enhancement of tensile strength.

  1. Strain hardening behavior and microstructural evolution during plastic deformation of dual phase, non-grain oriented electrical and AISI 304 steels

    Energy Technology Data Exchange (ETDEWEB)

    Soares, Guilherme Corrêa; Gonzalez, Berenice Mendonça; Arruda Santos, Leandro de, E-mail: leandro.arruda@demet.ufmg.br

    2017-01-27

    Strain hardening behavior and microstructural evolution of non-grain oriented electrical, dual phase, and AISI 304 steels, subjected to uniaxial tensile tests, were investigated in this study. Tensile tests were performed at room temperature and the strain hardening behavior of the steels was characterized by three different parameters: modified Crussard–Jaoul stages, strain hardening rate and instantaneous strain hardening exponent. Optical microscopic analysis, X-ray diffraction measurements, phase quantification by Rietveld refinement and hardness tests were also carried out in order to correlate the microstructural and mechanical responses to plastic deformation. Distinct strain hardening stages were observed in the steels in terms of the instantaneous strain hardening exponent and the strain hardening rate. The dual phase and non-grain oriented steels exhibited a two-stage strain hardening behavior while the AISI 304 steel displayed multiple stages, resulting in a more complex strain hardening behavior. The dual phase steels showed a high work hardening capacity in stage 1, which was gradually reduced in stage 2. On the other hand, the AISI 304 steel showed high strain hardening capacity, which continued to increase up to the tensile strength. This is a consequence of its additional strain hardening mechanism, based on a strain-induced martensitic transformation, as shown by the X-ray diffraction and optical microscopic analyses.

  2. Effects of strain and strain-induced α′-martensite on passive films in AISI 304 austenitic stainless steel

    International Nuclear Information System (INIS)

    Lv, Jinlong; Luo, Hongyun

    2014-01-01

    In this paper, the effects of strain and heat treatment on strain-induced α′-martensite of AISI 304 stainless steel tubes were measured by X-ray diffraction. Moreover, the effects of strain and content of α′-martensite on passivated property on the surface of the material in borate buffer solution were evaluated by electrochemical technique. The results showed that the volume fraction of α′-martensite increased gradually with the increase of tensile strain for as-received and solid solution samples. However, α′-martensite in as-received sample was more than that in the solid solution sample. The electrochemical impedance spectroscopy results showed that the solid solution treatment improved corrosion resistance of the steel, especially for samples with small strain. Moreover, acceptor densities were always higher than donor densities for as-received and solid solution samples. With the increase of strain, the increase tendency of acceptor density was more significant than that of donor density. We also found that the total density of the acceptor and donor almost increased linearly with the increase of α′-martensite. The present results indicated that the increased acceptor density might lead to the decreased corrosion resistance of the steel. - Highlights: • The solid solution treatment improved corrosion resistance of the stainless steel. • The deteriorated passivated property after strain could be attributed to the increased acceptor density. • The α′-martensite reduced corrosion resistance of the stainless steel

  3. Nanosecond laser surface modification of AISI 304L stainless steel: Influence the beam overlap on pitting corrosion resistance

    International Nuclear Information System (INIS)

    Pacquentin, Wilfried; Caron, Nadège; Oltra, Roland

    2014-01-01

    Surface modifications of AISI 304L stainless steel by laser surface melting (LSM) were investigated using a nanosecond pulsed laser-fibre doped by ytterbium at different overlaps. The objective was to study the change in the corrosion properties induced by the treatment of the outer-surface of the stainless steel without modification of the bulk material. Different analytical techniques such as scanning electron microscopy (SEM), X-ray diffraction (XRD), and glow discharge optical emission spectrometry (GDOES) were used to characterize the laser-melted surface. The corrosion resistance was evaluated in a chloride solution at room temperature by electrochemical tests. The results showed that the crystallographic structure, the chemical composition, the properties of the induced oxide layer and consequently the pitting corrosion resistance strongly depend on the overlap rate. The most efficient laser parameters led to an increase of the pitting potential by more than 300 mV, corresponding to a quite important improvement of the corrosion resistance. This latter was correlated to chromium enrichment (47 wt.%) at the surface of the stainless steel and the induced absence of martensite and ferrite phases. However, these structural and chemical modifications were not sufficient to explain the change in corrosion behaviour: defects and adhesion of the surface oxide layer must have been taken into consideration.

  4. Microstructure and tribology of ion-mixed Fe/Ti/C multilayers on AISI 304 stainless steel

    International Nuclear Information System (INIS)

    Nastasi, M.; Hirvonen, J.P.; Zocco, T.G.; Jervis, T.R.

    1991-01-01

    A multilayered Fe/Ti/C structure consisting of eleven alternating sublayers, four Fe, four Ti and three C, was ion mixed on an AISI 304 stainless steel substrate with 400 keV Xe 2+ . Complete mixing was observed after an irradiation of 1x10 17 Xe/cm 2 at 550degC. Electron diffraction revealed the formation of the compounds TiC and Fe 3 C and a small amount of an amorphous phase. Some samples were given a second irradiation with 5x10 15 Xe/cm 2 at 0degC. The phases present following the second irradiation were TiC, α-Fe and an amorphous phase. Tribological and nanoindentation measurements revealed that both types of samples possessed similar hardness and friction properties. The ion mixed samples possessed an increased hardness and a decreased friction coefficient relative to untreated polished stainless-steel substrate. However, the wear life of the hot ion mixed sample was consistently longer than the wear life of the sample processed at both 550 and 0degC. These results are explained by differences in adhesive wear which result from differences in the chemical reactivity of the phases formed during ion beam processing. (orig.)

  5. Influence of pre-deformation, sensitization and oxidation in high temperature water on corrosion resistance of AISI 304 stainless steel

    Energy Technology Data Exchange (ETDEWEB)

    Lv, Jinlong, E-mail: ljltsinghua@126.com [Beijing Key Laboratory of Fine Ceramics, Institute of Nuclear and New Energy Technology, Tsinghua University, Zhongguancun Street, Haidian District, Beijing 100084 (China); State Key Lab of New Ceramic and Fine Processing, Tsinghua University, Beijing 100084 (China); Liang, Tongxiang [Beijing Key Laboratory of Fine Ceramics, Institute of Nuclear and New Energy Technology, Tsinghua University, Zhongguancun Street, Haidian District, Beijing 100084 (China); State Key Lab of New Ceramic and Fine Processing, Tsinghua University, Beijing 100084 (China); Luo, Hongyun [Key Laboratory of Aerospace Materials and Performance (Ministry of Education), School of Materials Science and Engineering, Beijing University of Aeronautics and Astronautics, Xueyuan Road 37, Beijing 100191 (China)

    2016-12-01

    Highlights: • The pre-strain accelerated desensitization and sensitization for austenitic stainless steels. • Low temperature sensitization (carbide precipitation) induced α′-martensite. • The sensitization level could affect directly corrosion resistance of the oxide film. - Abstract: The effects of pre-deformation on sensitization of AISI 304 stainless steel were investigated by the double loop electrochemical potentiokinetic reactivation test. The effects of pre-deformation and sensitization on high temperature oxidized film formed in high temperature water were analyzed by a XRD and SEM. The electrochemical impedance spectroscopy at room temperature was used to study corrosion resistance of oxidized film. The point defect density of oxidized film was calculated by Mott–Schottky plots. The results showed that the value of the degree of sensitization first decreased and then slight increased with the increasing of engineering strain. Moreover, low temperature promoted to form sensitization induced “secondary” α′-martensite. The sample with 20% engineering strain had higher impedance value than other samples. The result was supported by further Mott–Schottky experiments. Considering increased α′-martensite with the increasing of strain, the results of the impedance were more consistent with values of the degree of sensitization.

  6. Martensite phase reversion-induced nano/ ultrafine grained AISI 304L stainless steel with magnificent mechanical properties

    Directory of Open Access Journals (Sweden)

    Mohammad Shirdel

    2015-06-01

    Full Text Available Austenitic stainless steels are extensively used in various applications requiring good corrosion resistance and formability. In the current study, the formation of nano/ ultrafine grained austenitic microstructure in a microalloyed AISI 304L stainless steel was investigated by the advanced thermomechanical process of reversion of strain-induced martensite. For this purpose, samples were subjected to heavy cold rolling to produce a nearly complete martensitic structure. Subsequently, a wide range of annealing temperatures (600 to 800°C and times (1 to 240 min were employed to assess the reversion behavior and to find the best annealing condition for the production of the nano/ultrafine grained austenitic microstructure. Microstructural characterizations have been performed using X-ray diffraction (XRD, scanning electron microscopy (SEM, and magnetic measurement, whereas the mechanical properties were assessed by tensile and hardness tests. After thermomechanical treatment, a very fine austenitic structure was obtained, which was composed of nano sized grains of ~ 85 nm in an ultrafine grained matrix with an average grain size of 480 nm. This microstructure exhibited superior mechanical properties: high tensile strength of about 1280 MPa with a desirable elongation of about 41%, which can pave the way for the application of these sheets in the automotive industry.

  7. The role of martensitic transformation on bimodal grain structure in ultrafine grained AISI 304L stainless steel

    International Nuclear Information System (INIS)

    Sabooni, S.; Karimzadeh, F.; Enayati, M.H.; Ngan, A.H.W.

    2015-01-01

    In the present study, metastable AISI 304L austenitic stainless steel samples were subjected to different cold rolling reductions from 70% to 93%, followed by annealing at 700 °C for 300 min to form ultrafine grained (UFG) austenite with different grain structures. Transmission electron microscopy (TEM) and nanoindentation were used to characterize the martensitic transformation, in order to relate it to the bimodal distribution of the austenite grain size after subsequent annealing. The results showed that the martensite morphology changed from lath type in the 60% rolled sample to a mixture of lath and dislocation-cell types in the higher rolling reductions. Calculation of the Gibbs free energy change during the reversion treatment showed that the reversion mechanism is shear controlled at the annealing temperature and so the morphology of the reverted austenite is completely dependent on the morphology of the deformation induced martensite. It was found that the austenite had a bimodal grain size distribution in the 80% rolled and annealed state and this is related to the existence of different types of martensite. Increasing the rolling reduction to 93% followed by annealing caused changing of the grain structure to a monomodal like structure, which was mostly covered with small grains of around 300 nm. The existence of bimodal austenite grain size in the 80% rolled and annealed 304L stainless steel led to the improvement of ductility while maintaining a high tensile strength in comparison with the 93% rolled and annealed sample

  8. The electrochemical behaviour of stainless steel AISI 304 in alkaline solutions with different pH in the presence of chlorides

    International Nuclear Information System (INIS)

    Freire, L.; Carmezim, M.J.; Ferreira, M.G.S.; Montemor, M.F.

    2011-01-01

    Highlights: → The passivation and passivation breakdown of AISI 304 in alkaline solutions with different pH was studied. → The electrochemical behaviour and the corrosion resistance in chloride environments were evaluated using d.c. potentiodynamic polarization and electrochemical impedance spectroscopy. → The results were modelled using a hierarchically distributed circuit and revealed a more susceptible surface at pH 9. → The passive film characterization was carried out by SEM and EDS analysis, revealing the existence of MnS inclusions and the increase of Cr/Fe ratio in the attacked areas, preferably the vicinity of those inclusions. - Abstract: Nowadays, stainless steel reinforcements appear as an effective solution to increase the durability of reinforced concrete structures exposed to very aggressive environments. AISI 304 is widely used for this purpose. Although the improved durability of reinforcing AISI 304, when compared to carbon steel, there is a high probability of pitting susceptibility in the presence of chlorides. Thus, the present work aims at studying the passivation and passivation breakdown of AISI 304 in alkaline solutions of different pH (pH from 13 to 9), simulating the interstitial concrete electrolyte. These solutions were contaminated with different concentrations of chloride ions (3% and 10%, as NaCl). The electrochemical behaviour was evaluated by d.c. potentiodynamic polarization and by electrochemical impedance spectroscopy (EIS). The morphological features and the changes observed in the surface composition were evaluated by Scanning Electron Microscopy (SEM) together with EDS chemical analysis. The results evidence that pH plays an important role in the evolution of the film resistance and charge transfer processes. Moreover, the effect is highly dependent upon the chloride content and immersion time.

  9. Statistical study by digitalized image analysis of pitting corrosion of an AISI 304 type stainless steel in chloride environment

    International Nuclear Information System (INIS)

    Lacome, Isabelle

    1994-01-01

    This research thesis addresses the pitting corrosion of an AISI 304-type stainless steel in chloride environment, a phenomenon which is generally considered as comprising two main steps: pit initiation with local degradation of the passive film, and pit growth. By using a technique of analysis of digitalized images, the process is observed in situ and both steps are monitored. A statistical study of the initiation of all the noticed pits is performed. After a bibliographical survey on the pitting corrosion process, its mechanisms and the influence of different parameters, the author presents the studied material and the experimental methods, reports the investigation of the pitting corrosion process in potentiostatic mode over a wide range of potentials in order to study all the types of pits, discusses the influence of potential on pit initiation and growth, reports the study of the influence of hydrodynamic conditions and of ageing in solution on the different parameters, reports the analysis of passive films by photoelectron spectroscopy, and the study of the influence of an inhibitor (molybdate ions) on both steps of pitting corrosion [fr

  10. Electrochemical study of AISI 304 stainless steel during the exposure at the disinfectant solutions with fungal suspensions

    Energy Technology Data Exchange (ETDEWEB)

    Stoica, M.; Bruma, M. [Department of Biochemistry and Technologies, Faculty of Food Science and Engineering, ' ' Dunarea de Jos' ' University of Galati, 111 Domneasca Street, 800201 Galati (Romania); Carac, G. [Department of Chemistry, Faculty of Sciences, ' ' Dunarea de Jos' ' University of Galati, 47 Domneasca Street, 800008 Galati (Romania)

    2010-12-15

    The effect of fungal suspensions on the disinfectant solution (Actisept with sodium dichloroisocyanurate as active substance, which releases 140 ppm active chlorine) and the corrosion behavior of type AISI 304 stainless steel (SS) were evaluated through linear polarization. The work presents a study of biocide Actisept solution as reference solution and the mixed solutions: reference biocide Actisept solution with three fungal suspensions (10 vol%), Aspergillus niger, Candida mycoderma, and Saccharomyces cerevisiae. The fungal suspension has an important influence on the synergistic effect of the SS corrosion in the following order: Saccharomyces cerevisiae > Candida mycoderma > Aspergillus niger. The E{sub corr} values from the mixed solutions decreased with immersion time of the samples. In the case of Aspergillus niger, the corrosion rate was lower than that of any other type of fungal suspension tested, because the arrangement in solutions, the size and composition of Aspergillus niger spores were more favorable to protect the spores of the chemical and the electrical stressing. The results showed that there is a synergistic effect between the active substances from the disinfectant, fungal suspensions and applied potential, thus this effect can be taken into consideration for the hygienic and safety food industry. (Copyright copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  11. Effect of electropulsing on surface mechanical properties and microstructure of AISI 304 stainless steel during ultrasonic surface rolling process

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Haibo [Advanced Materials Institute, Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055 (China); Key Laboratory of Advanced Materials, Tsinghua University, Beijing 100084 (China); Song, Guolin [Advanced Materials Institute, Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055 (China); Tang, Guoyi, E-mail: tanggy@mail.tsinghua.edu.cn [Advanced Materials Institute, Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055 (China); Key Laboratory of Advanced Materials, Tsinghua University, Beijing 100084 (China)

    2016-04-26

    The present work integrates 3D digital optical microscopy (OM), nano-indentation, X-ray diffraction (XRD), scanning electron microscopy (SEM) with electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM) to systematically investigate the effect of electropulsing on the surface mechanical properties and microstructure of AISI 304 stainless steel during the ultrasonic surface rolling process (USRP). Compared with the original USRP, the introduction of electropulsing with optimal parameters can effectively facilitate surface crack healing and improve surface hardness and wear resistance dramatically, and the residual compressive stress is further enhanced. Meanwhile, more martensite phase and fewer deformation twins can be found in the strengthened layer. Rapid improvement of the surface mechanical properties should be attributed to the ultra-refined grains, accelerated martensitic phase transformation and suppressed deformation twining induced by the coupling effect of USRP and electropulsing. The high strain rate given by USRP, increased stacking fault energy and accelerated dislocation mobility caused by electropulsing are likely the primary intrinsic reasons for the observed phenomena.

  12. Microchemical and microstructural evolution of AISI 304 stainless steel irradiated in EBR-II at PWR-relevant dpa rates

    Energy Technology Data Exchange (ETDEWEB)

    Dong, Y. [Department of Materials Science and Engineering, University of Michigan, Ann Arbor, MI 48109 (United States); Sencer, B.H. [Idaho National Laboratory, Idaho Falls, ID 83402 (United States); Garner, F.A. [Radiation Effects Consulting, Richland, WA 99354 (United States); Marquis, E.A., E-mail: emarq@umich.edu [Department of Materials Science and Engineering, University of Michigan, Ann Arbor, MI 48109 (United States)

    2015-12-15

    AISI 304 stainless steel was irradiated at 416 °C and 450 °C at a 4.4 × 10{sup −9} and 3.05 × 10{sup −7} dpa/s to ∼0.4 and ∼28 dpa, respectively, in the reflector of the EBR-II fast reactor. Both unirradiated and irradiated conditions were examined using standard and scanning transmission electron microscopy, energy dispersive spectroscopy, and atom probe tomography on very small specimens produced by focused ion beam milling. These results are compared with previous electron microscopy examination of 3 mm disks from essentially the same material. By comparing a very low dose specimen with a much higher dose specimen, both derived from a single reactor assembly, it has been demonstrated that the coupled microstructural and microchemical evolution of dislocation loops and other sinks begins very early, with elemental segregation producing at these sinks what appears to be measurable precursors to fully formed precipitates found at higher doses. The nature of these sinks and their possible precursors are examined in detail.

  13. Microchemical and microstructural evolution of AISI 304 stainless steel irradiated in EBR-II at PWR-relevant dpa rates

    Science.gov (United States)

    Dong, Y.; Sencer, B. H.; Garner, F. A.; Marquis, E. A.

    2015-12-01

    AISI 304 stainless steel was irradiated at 416 °C and 450 °C at a 4.4 × 10-9 and 3.05 × 10-7 dpa/s to ∼0.4 and ∼28 dpa, respectively, in the reflector of the EBR-II fast reactor. Both unirradiated and irradiated conditions were examined using standard and scanning transmission electron microscopy, energy dispersive spectroscopy, and atom probe tomography on very small specimens produced by focused ion beam milling. These results are compared with previous electron microscopy examination of 3 mm disks from essentially the same material. By comparing a very low dose specimen with a much higher dose specimen, both derived from a single reactor assembly, it has been demonstrated that the coupled microstructural and microchemical evolution of dislocation loops and other sinks begins very early, with elemental segregation producing at these sinks what appears to be measurable precursors to fully formed precipitates found at higher doses. The nature of these sinks and their possible precursors are examined in detail.

  14. Characterization of welding of AISI 304l stainless steel similar to the core encircling of a BWR reactor

    International Nuclear Information System (INIS)

    Gachuz M, M.E.; Palacios P, F.; Robles P, E.F.

    2003-01-01

    Plates of austenitic stainless steel AISI 304l of 0.0381 m thickness were welded by means of the SMAW process according to that recommended in the Section 9 of the ASME Code, so that it was reproduced the welding process used to assemble the encircling of the core of a BWR/5 reactor similar to that of the Laguna Verde Nucleo electric plant, there being generated the necessary documentation for the qualification of the one welding procedure and of the welder. They were characterized so much the one base metal, as the welding cord by means of metallographic techniques, scanning electron microscopy, X-ray diffraction, mechanical essays and fracture mechanics. From the obtained results it highlights the presence of an area affected by the heat of up to 1.5 mm of wide and a value of fracture tenacity (J IC ) to ambient temperature for the base metal of 528 KJ/m 2 , which is diminished by the presence of the welding and by the increment in the temperature of the one essay. Also it was carried out an fractographic analysis of the fracture zone generated by the tenacity essays, what evidence a ductile fracture. The experimental values of resistance and tenacity are important for the study of the structural integrity of the encircling one of the core. (Author)

  15. Corrosion of stainless steel grades in molten NaOH/KOH eutectic at 250 C: AISI304 austenitic and 2205 duplex

    Energy Technology Data Exchange (ETDEWEB)

    Bozzini, B.; Bogani, F.; Scarselli, G. [Dipartimento di Ingegneria dell' Innovazione, Universita del Salento, Via per Monteroni, 73100 Lecce (Italy); Barella, S.; Boniardi, M. [Dipartimento di Meccanica, Politecnico di Milano, via La Masa 34, 20156 Milano (Italy); Giovannelli, G.; Natali, S. [Dipartimento DICMA, Universita di Roma ' ' La Sapienza' ' , via Eudossiana 18, 00184 Roma (Italy)

    2012-11-15

    The present paper focuses on the corrosion of an austenitic (AISI304) and a duplex (2205) stainless steel grade in molten KOH/NaOH 50 w/o eutectic at 250 C. Experimental activities have been performed consisting in electrochemical measurements (linear sweep voltammetry and electrochemical impedance spectrometry) complemented by metallographic (in-plane and cross-sectional SEM micrography), structural (X-ray diffractometry) and compositional (EDX line-profiles) characterisation of the materials attacked under electrochemically controlled conditions. Electrochemical measurements have shown that AISI304 exhibits a passivating behaviour, characterised by two passivation peaks and a transpassive threshold, while duplex, does not yield a clear indication of passivation. AISI304 was found to fail by intergranular corrosion and to be covered in both passive and transpassive conditions, by an incoherent scale, containing electrolyte species. Duplex samples, instead tends to fail by homogeneous attack and exhibit a range of scale structures, depending on the applied potential. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  16. Analysis of surface integrity in machining of AISI 304 stainless steel under various cooling and cutting conditions

    Science.gov (United States)

    Klocke, F.; Döbbeler, B.; Lung, S.; Seelbach, T.; Jawahir, I. S.

    2018-05-01

    Recent studies have shown that machining under specific cooling and cutting conditions can be used to induce a nanocrystalline surface layer in the workspiece. This layer has beneficial properties, such as improved fatigue strength, wear resistance and tribological behavior. In machining, a promising approach for achieving grain refinement in the surface layer is the application of cryogenic cooling. The aim is to use the last step of the machining operation to induce the desired surface quality to save time-consuming and expensive post machining surface treatments. The material used in this study was AISI 304 stainless steel. This austenitic steel suffers from low yield strength that limits its technological applications. In this paper, liquid nitrogen (LN2) as cryogenic coolant, as well as minimum quantity lubrication (MQL), was applied and investigated. As a reference, conventional flood cooling was examined. Besides the cooling conditions, the feed rate was varied in four steps. A large rounded cutting edge radius and finishing cutting parameters were chosen to increase the mechanical load on the machined surface. The surface integrity was evaluated at both, the microstructural and the topographical levels. After turning experiments, a detailed analysis of the microstructure was carried out including the imaging of the surface layer and hardness measurements at varying depths within the machined layer. Along with microstructural investigations, different topological aspects, e.g., the surface roughness, were analyzed. It was shown that the resulting microstructure strongly depends on the cooling condition. This study also shows that it was possible to increase the micro hardness in the top surface layer significantly.

  17. Comparison of high temperature wear behaviour of plasma sprayed WC–Co coated and hard chromium plated AISI 304 austenitic stainless steel

    International Nuclear Information System (INIS)

    Balamurugan, G.M.; Duraiselvam, Muthukannan; Anandakrishnan, V.

    2012-01-01

    Highlights: ► WC–12wt.%Co powders were deposited to a thickness of 300 μm on to steel substrates. ► The micro hardness of the above coatings was lower than that of chromium plating. ► Wear resistance of chromium coating was increased up to five times of AISI 304 austenitic stainless steel. ► Wear resistance of chromium coat higher than plasma coat at different temperatures. -- Abstract: The wear behaviour of plasma sprayed coating and hard chrome plating on AISI 304 austenitic stainless steel substrate is experimentally investigated in unlubricated conditions. Experiments were conducted at different temperatures (room temp, 100 °C, 200 °C and 300 °C) with 50 N load and 1 m/s sliding velocity. Wear tests were carried out by dry sliding contact of EN-24 medium carbon steel pin as counterpart on a pin-on-disc wear testing machine. In both coatings, specimens were characterised by hardness, microstructure, coating density and sliding wear resistance. Wear studies showed that the hard chromium coating exhibited improved tribological performance than that of the plasma sprayed WC–Co coating. X-ray diffraction analysis (XRD) of the coatings showed that the better wear resistance at high temperature has been attributed to the formation of a protective oxide layer at the surface during sliding. The wear mechanisms were investigated through scanning electron microscopy (SEM) and XRD. It was observed that the chromium coating provided higher hardness, good adhesion with the substrate and nearly five times the wear resistance than that obtained by uncoated AISI 304 austenitic stainless steel.

  18. Effect of Built-Up Edge Formation during Stable State of Wear in AISI 304 Stainless Steel on Machining Performance and Surface Integrity of the Machined Part.

    Science.gov (United States)

    Ahmed, Yassmin Seid; Fox-Rabinovich, German; Paiva, Jose Mario; Wagg, Terry; Veldhuis, Stephen Clarence

    2017-10-25

    During machining of stainless steels at low cutting -speeds, workpiece material tends to adhere to the cutting tool at the tool-chip interface, forming built-up edge (BUE). BUE has a great importance in machining processes; it can significantly modify the phenomenon in the cutting zone, directly affecting the workpiece surface integrity, cutting tool forces, and chip formation. The American Iron and Steel Institute (AISI) 304 stainless steel has a high tendency to form an unstable BUE, leading to deterioration of the surface quality. Therefore, it is necessary to understand the nature of the surface integrity induced during machining operations. Although many reports have been published on the effect of tool wear during machining of AISI 304 stainless steel on surface integrity, studies on the influence of the BUE phenomenon in the stable state of wear have not been investigated so far. The main goal of the present work is to investigate the close link between the BUE formation, surface integrity and cutting forces in the stable sate of wear for uncoated cutting tool during the cutting tests of AISI 304 stainless steel. The cutting parameters were chosen to induce BUE formation during machining. X-ray diffraction (XRD) method was used for measuring superficial residual stresses of the machined surface through the stable state of wear in the cutting and feed directions. In addition, surface roughness of the machined surface was investigated using the Alicona microscope and Scanning Electron Microscopy (SEM) was used to reveal the surface distortions created during the cutting process, combined with chip undersurface analyses. The investigated BUE formation during the stable state of wear showed that the BUE can cause a significant improvement in the surface integrity and cutting forces. Moreover, it can be used to compensate for tool wear through changing the tool geometry, leading to the protection of the cutting tool from wear.

  19. Propagation of crevices in stainless steel AISI304L in conditions of hydrogen chemistry (HWC); Propagacion de grietas en acero inoxidable AISI304L en condiciones de quimica de hidrogeno (HWC)

    Energy Technology Data Exchange (ETDEWEB)

    Diaz S, A.; Fuentes C, P.; Merino C, F. [ININ, 52750 Ocoyoacac, Estado de Mexico (Mexico); Castano M, V. [IFA-UNAM, Juriquilla, Queretaro (Mexico)]. e-mail: ads@nuclear.inin.mx

    2006-07-01

    Crevice growth velocities in samples of AISI 304L stainless steel thermally welded and sensitized were obtained by the Rising displacement method or of growing displacement. It was used a recirculation circuit in where the operation conditions of a BWR type reactor were simulated (temperature of 288 C and a pressure of 8 MPa) with the chemistry modified by the addition of hydrogen with and without the addition of impurities of a powerful oxidizer like the Cu{sup ++} ion. CT pre cracked specimens were used and each rehearsal stayed to one constant displacement velocity of 1 x 10{sup -9} m/s (3.6 {mu}m/hr), making a continuous pursuit of the advance of the crack by the electric potential drop technique. To the end of the rehearsal it was carried out the fractographic analysis of the propagation surfaces. The values of the growth velocities obtained by this methodology went similar to the opposing ones under normal conditions of operation; while the fractographic analysis show the cracks propagation in trans and intergranular ways, evidencing the complexity of the regulator mechanisms of the one IGSCC even under controlled ambient conditions or with mitigation methodologies like the alternative hydrogen chemistry. (Author)

  20. Characterization of welding of AISI 304l stainless steel similar to the core encircling of a BWR reactor; Caracterizacion de soldaduras de acero inoxidable AISI 304L similares a las de la envolvente del nucleo de un reactor BWR

    Energy Technology Data Exchange (ETDEWEB)

    Gachuz M, M.E.; Palacios P, F.; Robles P, E.F. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

    2003-07-01

    Plates of austenitic stainless steel AISI 304l of 0.0381 m thickness were welded by means of the SMAW process according to that recommended in the Section 9 of the ASME Code, so that it was reproduced the welding process used to assemble the encircling of the core of a BWR/5 reactor similar to that of the Laguna Verde Nucleo electric plant, there being generated the necessary documentation for the qualification of the one welding procedure and of the welder. They were characterized so much the one base metal, as the welding cord by means of metallographic techniques, scanning electron microscopy, X-ray diffraction, mechanical essays and fracture mechanics. From the obtained results it highlights the presence of an area affected by the heat of up to 1.5 mm of wide and a value of fracture tenacity (J{sub IC}) to ambient temperature for the base metal of 528 KJ/m{sup 2}, which is diminished by the presence of the welding and by the increment in the temperature of the one essay. Also it was carried out an fractographic analysis of the fracture zone generated by the tenacity essays, what evidence a ductile fracture. The experimental values of resistance and tenacity are important for the study of the structural integrity of the encircling one of the core. (Author)

  1. Crack propagation in stainless steel AISI 304L in Hydrogen Chemistry conditions (HWC); Propagacion de Grietas en Acero Inoxidable AISI 304L en Condiciones de Quimica de Hidrogeno (HWC)

    Energy Technology Data Exchange (ETDEWEB)

    Diaz S, A.; Fuentes C, P.; Merino C, F. [ININ, Carretera Mexico -Toluca s/n, La Marquesa, Ocoyoacac, Mexico (Mexico); Castano M, V. [Instituto de Fisica Aplicada, UNAM, Km 15.5 Carretera Queretaro-San Luis Potosi, Juriquilla, Queretaro (Mexico)]. e-mail: ads@nuclear.inin.mx

    2006-07-01

    Velocities of crack growth in samples type CT pre cracking of stainless steel AISI 304l solder and sensitized thermally its were obtained by the Rising Displacement method or of growing displacement. It was used a recirculation circuit that simulates the operation conditions of a BWR type reactor (temperature of 280 C and a pressure of 8 MPa) with the chemistry modified by the addition of hydrogen with and without the addition of impurities of a powerful oxidizer like the Cu{sup +} ion. In each essay stayed a displacement velocity was constant of 1x10{sup -9} m/s, making a continuous pursuit of the advance of the crack by the electric potential drop technique. Contrary to the idea of mitigation of the crack propagation velocity by effect of the addition of the hydrogen in the system, the values of the growth velocities obtained by this methodology went similar to the opposing ones under normal operation conditions. To the finish of the rehearsal one carries out the fractographic analysis of the propagation surfaces, which showed cracks growth in trans and intergranular way, evidencing the complexity of the regulator mechanisms of the IGSCC like in mitigation conditions as the alternative Hydrogen Chemistry. (Author)

  2. Effect of heat input on the microstructure and mechanical properties of gas tungsten arc welded AISI 304 stainless steel joints

    International Nuclear Information System (INIS)

    Kumar, Subodh; Shahi, A.S.

    2011-01-01

    Highlights: → Welding procedure is established for welding 6 mm thick AISI 304 using GTAW process. → Mechanical properties of the weld joints are influenced strongly by the heat input. → Highest tensile strength of 657.32 MPa is achieved by joints using low heat input. → Welding parameters affect heat input and hence microstructure of weld joints. → Extent of grain coarsening in the HAZ increases with increase in the heat input. -- Abstract: Influence of heat input on the microstructure and mechanical properties of gas tungsten arc welded 304 stainless steel (SS) joints was studied. Three heat input combinations designated as low heat (2.563 kJ/mm), medium heat (2.784 kJ/mm) and high heat (3.017 kJ/mm) were selected from the operating window of the gas tungsten arc welding process (GTAW) and weld joints made using these combinations were subjected to microstructural evaluations and tensile testing so as to analyze the effect of thermal arc energy on the microstructure and mechanical properties of these joints. The results of this investigation indicate that the joints made using low heat input exhibited higher ultimate tensile strength (UTS) than those welded with medium and high heat input. Significant grain coarsening was observed in the heat affected zone (HAZ) of all the joints and it was found that the extent of grain coarsening in the heat affected zone increased with increase in the heat input. For the joints investigated in this study it was also found that average dendrite length and inter-dendritic spacing in the weld zone increases with increase in the heat input which is the main reason for the observable changes in the tensile properties of the weld joints welded with different arc energy inputs.

  3. The effect of inhibitor sodium nitrate on pitting corrosion of dissimilar material weldment joint of stainless steel AISI 304 and mild steel SS 400

    Energy Technology Data Exchange (ETDEWEB)

    Hilca, B. R., E-mail: bangkithilca@yahoo.com; Triyono, E-mail: triyonomesin@uns.ac.id [Mechanical Engineering Department, Sebelas Maret University, Surakarta 57126 (Indonesia)

    2016-03-29

    This study experimentally evaluated the effect of Sodium Nitrate inhibitor (NaNO{sub 3}) of 0.1%, 0.3%, and 0.5% on NaCl 3.5% toward pitting corrosion of dissimilar metal welding joint between stainless steel AISI 304 and mild steel SS 400. Electrochemical corrosion was tested using potentiodynamic polarization. Further the Scanning Electron Microscope (SEM) conducted to analyze the specimen. Chemical composition analysis used Energy Dispersive X-ray Spectrometry (EDS). The highest efficiency of sodium nitrate for ER 308 attained 63.8% and 64.89%for ER 309L. The specimen surface which observed through SEM showed decrease of pitting corrosion respectively with the addition of sodium nitrate content as inhibitor.

  4. Influence of carbide precipitation upon hydrogen fragilization of an AISI 304 steel

    International Nuclear Information System (INIS)

    Hazarabedian, A.E.; Ovejero Garcia, J.

    1991-01-01

    The present work deals with austenitic stainless steels for a family of steels that is renowned for its high resistance to hydrogen fragilization. Nevertheless, these steels may suffer hydrogen fragilization under severe working conditions. This fact is strongly dependent on many factors -composition, grain size, other phases present, corrosion sensitivity, etc.-. While there are studies that show how intergranular corrosion is influenced by corrosion sensitivity -mainly due to carbide precipitation in grain boundaries-, there are no reports about the effect of the carbide precipitation itself on hydrogen fragilization for these steels. (Author) [es

  5. Velocities and mechanisms of AISI 304 steel corrosion in heated acid solutions

    International Nuclear Information System (INIS)

    Silva, B.M.; Guedes, C.D.

    1984-01-01

    The corrosion resistance of stainless steel on H 2 SO 4 at temperature higher than 60 0 C is studied. The weight loss technique and the analysis of the different components in solution are used. A proposition is made about the reason for the loss of resistance to corrosion of the stainless steel at this high temperature. (C.L.B.) [pt

  6. TEM examination of the effect of post-irradiation annealing on 7.7 dpa AISI 304 stainless steel

    International Nuclear Information System (INIS)

    Karlsen, W.; Ivanchenko, M.; Pakarinen, J.; Karlsen, T.

    2015-01-01

    Stainless steels exposed to neutron irradiation during service in light water reactors (LWR) can become susceptible to intergranular cracking, referred to as irradiation assisted stress corrosion cracking (IASCC). Analytical transmission electron microscopy (ATEM) was used to examine the effect of post-irradiation annealing (PIA) on radiation-induced segregation (RIS) at the grain boundaries of 7.7 dpa AISI 304 stainless steel. The grain boundary profiles and the irradiation damage were analysed in the as-irradiated state and after PIA of 6 hours at 500 C. degrees and after 25 hours at 500 C. degrees and 550 C. degrees by using transmission electron microscopy (TEM). As a main conclusion from the TEM examinations, the effects of PIA were found to be relatively small after only 6 hours, while after 25 hours of PIA at both 500 and 550 C. degrees, RIS was almost recovered and only marginal deviation in chemical composition could be found near the GB. The as-irradiated state showed extreme RIS values of Si 4.9 wt%, Cr 14.7 wt%, Ni 23.4 wt%, and P 1.4 wt%., while upon PIA for 6 hours the extreme values for RIS were Si 3.9 wt%, Cr 16.0 wt%, Ni 21 wt%, and P 0.9 wt%. After 6 hours annealing at 500 C. dislocation loops start to grow, while dislocation density remains of the same order of magnitude. After annealing for 25 hours at 500 C. degrees the average size of dislocation loops remains nearly the same, while dislocation density was reduced almost by one fold. In the areas where dislocation density was found to be the lowest some features, which can most likely be attributed to stacking fault tetrahedral (SFT) were found. Annealing at even higher temperature (550 C.) affected the average size of the dislocation loops, making them almost twice as large as well as resulting in a very broad distribution of dislocation sizes. Density of dislocations is also reduced by one fold in comparison to the as irradiated condition and leads to formation of SFTs, which could be

  7. Corrosion fatigue of AISI 304 stainless steel in aqueous chloride solution

    International Nuclear Information System (INIS)

    Ferrao, P.R.; Sousa e Silva, A.S. de; Castro, M.A.C. de

    1982-01-01

    The fatique behaviour of an 304 austenitic stainless steel in a 0,5 M NaCl environment was studied. The material was tested, under different electrode potential conditions and the results were compaired with those obtained for tests in air. It has been shown by means of metallographic and fractografic observations, that the mechanism of crack initiation depends on the applied potential. (Author) [pt

  8. Effect of metallurgical variables on the austenite stability in fatigued AISI 304 type steels

    Czech Academy of Sciences Publication Activity Database

    Man, Jiří; Smaga, M.; Kuběna, Ivo; Eifler, D.; Polák, Jaroslav

    2017-01-01

    Roč. 185, NOV (2017), s. 139-159 ISSN 0013-7944. [XVIII International Colloquium Mechanical Fatigue of Metals. Gijón, 05.11.2016-07.11.2016] R&D Projects: GA ČR GA13-32665S Institutional support: RVO:68081723 Keywords : Austenitic stainless steel * Deformation induced martensite * Color metallography * Chemical banding * Low cycle fatigue Subject RIV: JL - Materials Fatigue, Friction Mechanics OBOR OECD: Audio engineering , reliability analysis Impact factor: 2.151, year: 2016

  9. Evaluation of structural behaviour and corrosion resistant of austenitic AISI 304 and duplex AISI 2304 stainless steel reinforcements embedded in ordinary Portland cement mortars

    International Nuclear Information System (INIS)

    Medina, E.; Cobo, A.; Bastidas, D. M.

    2012-01-01

    The mechanical and structural behaviour of two stainless steels reinforcements, with grades austenitic EN 1.4301 (AISI 304) and duplex EN 1.4362 (AISI 2304) have been studied, and compared with the conventional carbon steel B500SD rebar. The study was conducted at three levels: at rebar level, at section level and at structural element level. The different mechanical properties of stainless steel directly influence the behaviour at section level and structural element level. The study of the corrosion behaviour of the two stainless steels has been performed by electrochemical measurements, monitoring the corrosion potential and the lineal polarization resistance (LPR), of reinforcements embedded in ordinary Portland cement (OPC) mortar specimens contaminated with different amount of chloride over one year time exposure. Both stainless steels specimens embedded in OPC mortar remain in the passive state for all the chloride concentration range studied after one year exposure. (Author) 26 refs.

  10. Effects of Loading Frequency on Fatigue Behavior, Residual Stress, and Microstructure of Deep-Rolled Stainless Steel AISI 304 at Elevated Temperatures

    Science.gov (United States)

    Nikitin, I.; Juijerm, P.

    2018-02-01

    The effects of loading frequency on the fatigue behavior of non-deep-rolled (NDR) and deep-rolled (DR) austenitic stainless steel AISI 304 were systematically clarified at elevated temperatures, especially at temperatures exhibiting the dynamic strain aging (DSA) phenomena. Tension-compression fatigue tests were performed isothermally at temperatures of 573 K and 773 K (300 °C and 500 °C) with different loading frequencies of 5, 0.5, 0.05, and 0.005 Hz. For the DR condition, the residual stresses and work-hardening states will be presented. It was found that DSA would be detected at appropriate temperatures and deformation rates. The cyclic deformation curves and the fatigue lives of the investigated austenitic stainless steel AISI 304 are considerably affected by the DSA, especially on the DR condition having high dislocation densities at the surface and in near-surface regions. In the temperature range of the DSA, residual stresses and work-hardening states of the DR condition seem to be stabilized. The microstructural alterations were investigated by transmission electron microscopy (TEM). At an appropriate temperature with low loading frequency, the plastic deformation mechanism shifted from a wavy slip manner to a planar slip manner in the DSA regimes, whereas the dislocation movements were obstructed.

  11. Processing of fine grained AISI 304L austenitic stainless steel by cold rolling and high-temperature short-term annealing

    Science.gov (United States)

    Naghizadeh, Meysam; Mirzadeh, Hamed

    2018-05-01

    An advanced thermomechanical process based on the formation and reversion of deformation-induced martensite was used to refine the grain size and enhance the hardness of an AISI 304L austenitic stainless steel. Both low and high reversion annealing temperatures and also the repetition of the whole thermomechanical cycle were considered. While a microstructure with average austenite grain size of a few micrometers was achieved based on cold rolling and high-temperature short-term annealing, an extreme grain refinement up to submicrometer regime was obtained by cold rolling followed by low-temperature long-term annealing. However, the required annealing time was found to be much longer, which negates its appropriateness for industrial production. While a magnificent grain refinement was achieved by one pass of the high-temperature thermomechanical process, the reduction in grain size was negligible by the repetition of the whole cycle. It was found that the hardness of the thermomechanically processed material is much higher than that of the as-received material. The results of the present work were shown to be compatible with the general trend of grain size dependence of hardness for AISI 304L stainless steel based on the Hall-Petch relationship. The results were also discussed based on the X-ray evaluation of dislocation density by modified Williamson-Hall plots.

  12. Electropolishing of AISI-304 stainless steel using an oxidizing solution originally used for electrochemical coloration

    International Nuclear Information System (INIS)

    Andrade, Leonardo S.; Xavier, Sandro C.; Rocha-Filho, Romeu C.; Bocchi, Nerilso; Biaggio, Sonia R.

    2005-01-01

    Chemical polishing or electropolishing, instead of mechanical polishing, are recommended for the attainment of metallic surface polishes without the introduction of contaminants or tensions in the surface layers of the metal. The fundamental difference between the chemical and electrochemical polishing processes is that in the latter anodic currents/potentials are used to help in the dissolution and passivation of the metal. In this paper, the use of an oxidizing electrolytic solution (2.5 mol L -1 CrO 3 + 5.0 mol L -1 H 2 SO 4 ) originally employed in electrochemical coloration processes is reported for the electropolishing of AISI-314 stainless steel. Parameters involved in this electropolishing process, such as temperature, current density and time, were optimized so as to attain the best possible results evaluated by the obtained surface brightness measured by reflectance spectra. Surface analyses by scanning electron microscopy allowed a clear correlation between obtained brightness and surface smoothing. The best conditions obtained for the electropolishing process are: temperature of 45 deg. C, electrolysis time of 10 min and current density of around 25 A dm -2 . It should be pointed out that an electropolishing process signature (periodic oscillations of the cell potential) was established; this may be an important tool for optimizing and monitoring electropolishing processes

  13. pH effect on pit potential and protection potential of stainless steels AISI-304, 310 and 316 in NaCl solution

    International Nuclear Information System (INIS)

    Cabral, U.Q.; Sathler, L.; Mariano Neto, F.

    1973-06-01

    For three austenitic stainless steels, AISI 304, 310 and 316, the pH influence on the rupture, protection and corrosion potentials was studied in a 0,5N NACl solution. The pit potentials determined by the chronogalvonometric method, are pH independent within the acid range. They showed a rough linear variation within the basic range having a maximum corresponding to the pH value of 8.8. The electrochemical hysteresis method, employed for determining the protection potential, presented a total pH independence for the AISI 316. The other steels showed a small dependence within the basic range but with a tendency for the protection potential to become slightly more active with increasing pH, within the acid range. It was also noted for the three steels studied that the corrosion potental became more active with increasing pH, within the basic range [pt

  14. Effect of strain-path on stress corrosion cracking of AISI 304L stainless steel in PWR primary environment at 360 deg. C

    International Nuclear Information System (INIS)

    Couvant, T.; Vaillant, F.; Boursier, JM.; Delafosse, D.

    2004-01-01

    Austenitic stainless steels (ASS) are widespread in primary and auxiliary circuits of PWR. Moreover, some components suffer stress corrosion cracking (SCC) under neutron irradiation. This degradation could be the result of the increase of hardness or the modification of chemical composition at the grain boundary by irradiation. In order to avoid complex and costly corrosion facilities, the effects of irradiation on the material are commonly simulated by applying a cold work on non-irradiated material prior to stress corrosion cracking tests. Slow strain rate tests were conducted on an austenitic stainless steel (SS) AISI 304L in PWR environment (360 deg. C). Particular attention was directed towards pre-straining effects on crack growth rate (CGR) and crack growth path (CGP). Results have demonstrated that the susceptibility of 304L to SCC in high-temperature hydrogenated water was enhanced by pre-straining. It seemed that IGSCC was enhanced by complex strain paths. (authors)

  15. Effect of microstructure and chemical composition on localized corrosion resistance of a AISI 304L stainless steel after nanopulsed-laser surface melting

    International Nuclear Information System (INIS)

    Pacquentin, W.; Caron, N.; Oltra, R.

    2015-01-01

    Highlights: • Laser surface melting treatments require neither additional feedstock nor contact. • By affecting 1 μm, the pitting potential of laser treated 304L increases by 500 mV. • Surface modification of laser treated sample observed by TEM. • The physico-chemical properties of the surface are correlated to overlap rate. • AISI 304L pitting corrosion resistance strongly depends of overlap rate. - Abstract: Changes induced in the surface properties of AISI 304L stainless steel when it is treated with a nanopulsed ytterbium-doped fiber laser were investigated to determine the microscale distribution of its physico-chemical properties. A Gaussian energy distribution was created with a radius of 71 μm (1/e 2 ) at the focal point. Local investigations were carried out using transmission electron microscopy to consider the effect of overlapping individual laser impacts. The results obtained reveal that laser surface melting leads to changes in the crystallographic structure of the steel through the formation of a δ-ferritic phase. It also results in the creation of an oxide layer that increases the corrosion resistance of the steel, with the chemical composition, structure and thickness of this layer being dependent on the overlap percentage and the position along the beam radius. Measurement of the localized corrosion resistance in a 30 g L −1 NaCl solution using polarization curves found that optimal laser treatment conditions can led to an increase in the breakdown potential of more than 500 mV, which corresponds to a significant improvement in corrosion resistance.

  16. Response to annealing and reirradiation of AISI 304L stainless steel following initial high-dose neutron irradiation in EBR-II

    International Nuclear Information System (INIS)

    Porter, D.L.; McVay, G.L.; Walters, L.C.

    1980-01-01

    The object of this study was to measure the stability of irradiation-induced microstructure upon annealing and, by selectively annealing out some of these features and reirradiating the material, it was expected that information could be gained concerning the role of microstructural changes in the void swelling process. Transmission electron microscopic examinations of isochronally annealed (200 to 1050 0 C) AISI 304L stainless steel, which had been irradiated at approximately 415 0 C to a fast (E > 0.1 MeV) neutron fluence of approximately 5.1 x 10 26 n/m 2 , verified that the two-stage hardness recovery with temperatures was related to a low temperature annealing of dislocation structures and a higher temperature annealing of voids and solute redistribution

  17. Mechanical and tribological properties of AISI 304 stainless steel nitrided by glow discharge compared to ion implantation and plasma immersion ion implantation

    International Nuclear Information System (INIS)

    Foerster, C.E.; Serbena, F.C.; Silva, S.L.R. da; Lepienski, C.M.; Siqueira, C.J. de M.; Ueda, M.

    2007-01-01

    Results about mechanical and tribological behavior of AISI 304 stainless steel nitrided by three different ion beam processes - glow discharge (GD), ion implantation (II) and plasma immersion ion implantation (PI3) are reported. Expanded austenite γ N and nitrides phases (Fe 2+x N, γ'-Fe 4 N and Cr-N) were identified as a function of nitriding conditions. Hardness (H) and elastic modulus (E) profiles were obtained by instrumented penetration. The hardness reached values as high as 21 GPa by PI3. Tribological behavior was studied by reciprocating sliding tests with a WC (Co) ball at room temperature (RT) in dry condition. Different wear regimes were identified in the friction coefficient profiles. The profile form and the running-in distance are strongly dependent on the nitriding process. Adhesive and abrasive wear components can be inferred from these friction profiles. Hardness and tribological performance, after the nitriding processes, are discussed in terms of surface microstructure

  18. Strain-induced phase transformation at the surface of an AISI-304 stainless steel irradiated to 4.4 dpa and deformed to 0.8% strain

    Energy Technology Data Exchange (ETDEWEB)

    Gussev, M.N., E-mail: gussevmn@ornl.gov; Field, K.G.; Busby, J.T.

    2014-03-15

    Surface relief due to localized deformation in a 4.4-dpa neutron-irradiated AISI 304 stainless steel was investigated using scanning electron microscopy coupled with electron backscattering diffraction and scanning transmission electron microscopy. It was found a body-centered-cubic (BCC) phase (deformation-induced martensite) had formed at the surface of the deformed specimen along the steps generated from dislocation channels. Martensitic hill-like formations with widths of ∼1 μm and depths of several microns were observed at channels with heights greater than ∼150 nm above the original surface. Martensite at dislocation channels was observed in grains along the [0 0 1]–[1 1 1] orientation but not in those along the [1 0 1] orientation.

  19. Strain-induced phase transformation at the surface of an AISI-304 stainless steel irradiated to 4.4 dpa and deformed to 0.8% strain

    International Nuclear Information System (INIS)

    Gussev, M.N.; Field, K.G.; Busby, J.T.

    2014-01-01

    Surface relief due to localized deformation in a 4.4-dpa neutron-irradiated AISI 304 stainless steel was investigated using scanning electron microscopy coupled with electron backscattering diffraction and scanning transmission electron microscopy. It was found a body-centered-cubic (BCC) phase (deformation-induced martensite) had formed at the surface of the deformed specimen along the steps generated from dislocation channels. Martensitic hill-like formations with widths of ∼1 μm and depths of several microns were observed at channels with heights greater than ∼150 nm above the original surface. Martensite at dislocation channels was observed in grains along the [0 0 1]–[1 1 1] orientation but not in those along the [1 0 1] orientation

  20. The influence of silicon as a possible reactive element in the protection against high temperature oxidation of AISI 304 stainless steel

    International Nuclear Information System (INIS)

    Otero, E.; Perez, F.J.; Hierro, M.P.; Gomez, C.; Pedraza, F.; Segovia, J. L. de; Roman, E.

    1998-01-01

    The influence of silicon incorporated into the alloy by means of ion implantation of 1 x 10''15 ions/cm''2 at 150 keV on the protective scale development based upon Cr 1 ,3 Fe 0 ,7O 3 and manganese-enriched spinels, Mn 1 ,5Cr 1 .5O 4 after oxidation of an austenitic AISI 304 stainless steel at 1.173 K and atmospheric pressure of air for 144 h has been studied. The presence of small quantities of silicon at the outermost layers of the alloy promotes transport of chromium during the early stages of oxidation. Further, ion implantation seems to play a beneficial role against decarburization of the alloy. (Author) 8 refs

  1. Correlation between residual stress and plastic strain amplitude during low cycle fatigue of mechanically surface treated austenitic stainless steel AISI 304 and ferritic-pearlitic steel SAE 1045

    Energy Technology Data Exchange (ETDEWEB)

    Nikitin, I. [Institute of Materials Engineering, University of Kassel, 34125 Kassel, Hessen (Germany)], E-mail: Ivan.Nikitin@infineon.com; Besel, M. [Institute of Materials Engineering, University of Kassel, 34125 Kassel, Hessen (Germany)

    2008-09-15

    Mechanical surface treatments such as deep rolling are known to affect the near-surface microstructure and induce, e.g. residual stresses and/or increase the surface hardness. It is well known that, e.g. compressive residual stress states usually increase the lifetime under fatigue loading. The stress relaxation behaviour and the stability of the residual stress during fatigue loading depend on the mechanical surface treatment method. In this paper three different surface treatments are used and their effects on the low cycle fatigue behaviour of austenitic stainless steel (AISI 304) and ferritic-pearlitic steel (SAE 1045) are investigated. X-ray diffraction is applied for the non-destructive evaluation of the stress state and the microstructure. It is found that consecutive deep rolling and annealing as well as high temperature deep rolling produce more stable near-surface stress states than conventional deep rolling at room temperature. The plastic strain amplitudes during fatigue loading are measured and it is shown that they correlate well with the induced residual stress and its relaxation, respectively. Furthermore, Coffin-Manson plots are presented which clearly show the correlation between the plastic strain amplitude and the fatigue lifetime.

  2. Investigation of the Weld Properties of Dissimilar S32205 Duplex Stainless Steel with AISI 304 Steel Joints Produced by Arc Stud Welding

    Directory of Open Access Journals (Sweden)

    Aziz Barış Başyiğit

    2017-03-01

    Full Text Available UNS S32205 duplex stainless steel plates with a thickness of 3 mm are arc stud welded by M8 × 40 mm AISI 304 austenitic stainless steel studs with constant stud lifts in order to investigate the effects of welding arc voltages on mechanical and microstructural behaviors of the joints. As the welding arc voltage increases starting from 140 V, the tensile strength of the weldment also increases but the higher arc values results in more spatters around the weld seam up to 180 V. Conversely, the lower arc voltages causes poor tensile strength values to weldments. Tensile tests proved that all of the samples are split from each other in the welding zone but deformation occurs in duplex plates during the tensile testing of weldments so that the elongation values are not practically notable. The satisfactory tensile strength and bending values are determined by applying 180 volts of welding arc voltage according to ISO 14555 standard. Peak values of micro hardness occurred in weld metal most probably as a consequence of increasing heat input decreasing the delta ferrite ratios. As the arc voltage increases, the width of the heat affected zone increases. Coarsening of delta-ferrite and austenite grains was observed in the weld metal peak temperature zone but it especially becomes visible closer to the duplex side in all samples. The large voids and unwelded zones up to approximately 1 mm by length are observed by macro-structure inspections. Besides visual tests and micro-structural surveys; bending and microhardness tests with radiographic inspection were applied to samples for maintaining the correct welding parameters in obtaining well-qualified weldments of these two distinct groups of stainless steel materials.

  3. Aluminum coating by fluidized bed chemical vapor deposition on austenitic stainless steels AISI 304 and AISI 316

    Directory of Open Access Journals (Sweden)

    Jose Luddey Marulanda-Arevalo

    2015-01-01

    Full Text Available Los revestimientos de aluminio f ueron depositados sobre aceros inoxidables AISI 304 y AISI 316 en el rango de temperatura de 5 60 a 600 °C por deposición química de vapor en lecho fluidizado(CVD – FBR. Se utilizó un lecho que consistía en 10 % de aluminio en polvo y 90 % de lecho inerte (alúmina, el cual fue fluidizado con Ar y como ga ses activadores se utilizó una mezcla de ácido clorhídrico con hidrógeno (HCl/H 2 . En el recubrimiento si n tratamiento térmico están las siguiente s especies: Al 13 Fe 4 , Fe 2 Al 5 , FeAl 2 y Al 5 FeNi, las cuales están presentes para ambos aceros. Además, el tratamiento térmico provoca la difusa de alu minio hacia el sustrato y la difusa de hierro del sustrato haci a la superficie del recubrimiento, haciendo la trans formación de los compuestos ant eriores a FeAl, Fe 2 Al 5 , FeAl 2 , Al 0.99 Fe 0.99 Ni 0.02 , AlNi y el Fe 2 AlCr. Se realizó la simulación termodinámica con el s oftware Thermo Calc para obt ener información de la posible composición y la cantidad de mat erial depositado, para condiciones seleccionadas. Las muestras recubi ertas y sin recubrir, se expus ieron a 750 ºC en una atmósfera d onde el vapor agua se transporta a las muestras usando un flujo de N 2 de 40 ml/min, más 100 % vapor de agua (H 2 O. Los dos sustratos sin revestir se comportaron de manera diferente, ya que el acero AISI 304 soportó bien el a taque y ganó poco peso (0.49 mg/cm 2 , en comparación con el acero AISI 316 que perdió mucho peso (25.4 mg/cm 2 . Los aceros recubiertos ganaron poco de peso durante las mil horas de exposición (0.26 mg/cm 2 y soportaron muy bien el ataque corrosivo en c omparación con sustratos sin r ecubrimiento.

  4. Microstructure and corrosion resistance of nitrogen-rich surface layers on AISI 304 stainless steel by rapid nitriding in a hollow cathode discharge

    Science.gov (United States)

    Li, Yang; He, Yongyong; Zhang, Shangzhou; Wang, Wei; Zhu, Yijie

    2018-01-01

    Nitriding treatments have been successfully applied to austenitic stainless steels to improve their hardness and tribological properties. However, at temperatures above 450 °C, conventional plasma nitriding processes decrease the corrosion resistance due to the formation of CrN phases within the modified layer. In this work, AISI 304 austenitic stainless steels were efficiently treated by rapid plasma nitriding at a high temperature of 530 °C in a hollow cathode discharge. The enhanced ionization obtained in the hollow cathode configuration provided a high current density and, consequently, a high temperature could be attained in a short time. The nitrided layers were characterized by X-ray diffraction, scanning electron microscopy, atomic force microscopy, transmission electron microscopy and X-ray photoelectron spectroscopy. The results indicated that the dual-layer structure of the nitrided layer consists of a high-N face-centered cubic structure with a free CrN precipitate outer (top) layer and a nitrogen-expanded austenite S-phase bottom layer. The rapid nitriding-assisted hollow cathode discharge technique permits the use of high temperatures, as high as 530 °C, without promoting degradation in the corrosion resistance of stainless steel.

  5. Evaluation of structural behaviour and corrosion resistant of austenitic AISI 304 and duplex AISI 2304 stainless steel reinforcements embedded in ordinary Portland cement mortars; Evaluacion del comportamiento estructural y de resistencia a la corrosion de armaduras de acero inoxidable austenitico AISI 304 y duplex AISI 2304 embebidas en morteros de cemento Portland

    Energy Technology Data Exchange (ETDEWEB)

    Medina, E.; Cobo, A.; Bastidas, D. M.

    2012-07-01

    The mechanical and structural behaviour of two stainless steels reinforcements, with grades austenitic EN 1.4301 (AISI 304) and duplex EN 1.4362 (AISI 2304) have been studied, and compared with the conventional carbon steel B500SD rebar. The study was conducted at three levels: at rebar level, at section level and at structural element level. The different mechanical properties of stainless steel directly influence the behaviour at section level and structural element level. The study of the corrosion behaviour of the two stainless steels has been performed by electrochemical measurements, monitoring the corrosion potential and the lineal polarization resistance (LPR), of reinforcements embedded in ordinary Portland cement (OPC) mortar specimens contaminated with different amount of chloride over one year time exposure. Both stainless steels specimens embedded in OPC mortar remain in the passive state for all the chloride concentration range studied after one year exposure. (Author) 26 refs.

  6. Behavior to the fracture of an AISI 304 stainless steel sensitized in BWR reactor conditions (288 degrees Centigrade and 80 Kg/cm2)

    International Nuclear Information System (INIS)

    Hernandez C, R.; Diaz S, A.; Garcia R, R.; Aguilar T, A.; Gachuz M, M.; Arganis J, C.; Merino C, J.

    1999-01-01

    It is a knew fact that ductility of a lot of structural alloys can be deteriorated by the environment effect which are exposed, and that their consequent embrittlement can put in doubt the safety of their functioning; such is the case of austenitic stainless steels used in internal components of the BWR type reactors which not only is subjected to the effect combined of the aggressive environment which surround it (pressure, temperature, corrosion potential, conductivity medium, local state of efforts, etc.), but also to the action of present neutron radiation, manifesting microstructural changes which are reflected in the augmentation of its susceptibility to the intergranular cracking, phenomena generally known as IASCC ''Irradiation Assisted Stress Corrosion Cracking''. Once appeared the cracking in the material, the useful life of a component is limited by the rapidity to growth of these cracking, making necessary evaluations which can to predict its behavior, therefore the present work shows the preliminary results for determining the behavior to the fracture of an AISI 304 stainless steel sensitized, in a dynamic recirculation circuit which allows to simulate the operation conditions of a BWR reactor (288 Centigrade and 80 kg/cm 2 ). (Author)

  7. Plasma Nitriding of AISI 304 Stainless Steel in Cathodic and Floating Electric Potential: Influence on Morphology, Chemical Characteristics and Tribological Behavior

    Science.gov (United States)

    Li, Yang; He, Yongyong; Wang, Wei; Mao, Junyuan; Zhang, Lei; Zhu, Yijie; Ye, Qianwen

    2018-03-01

    In direct current plasma nitriding (DCPN), the treated components are subjected to a high cathodic potential, which brings several inherent shortcomings, e.g., damage by arcing and the edging effect. In active screen plasma nitriding (ASPN) processes, the cathodic potential is applied to a metal screen that surrounds the workload, and the component to be treated is placed in a floating potential. Such an electrical configuration allows plasma to be formed on the metal screen surface rather than on the component surface; thus, the shortcomings of the DCPN are eliminated. In this work, the nitrided experiments were performed using a plasma nitriding unit. Two groups of samples were placed on the table in the cathodic and the floating potential, corresponding to the DCPN and ASPN, respectively. The floating samples and table were surrounded by a steel screen. The DCPN and ASPN of the AISI 304 stainless steels are investigated as a function of the electric potential. The samples were characterized using scanning electron microscopy with energy-dispersive x-ray spectroscopy, x-ray diffraction, atomic force microscopy and transmission electron microscope. Dry sliding ball-on-disk wear tests were conducted on the untreated substrate, DCPN and ASPN samples. The results reveal that all nitrided samples successfully produced similar nitrogen-supersaturated S phase layers on their surfaces. This finding also shows the strong impact of the electric potential of the nitriding process on the morphology, chemical characteristics, hardness and tribological behavior of the DCPN and ASPN samples.

  8. The effect of residual thermal stresses on the fatigue crack growth of laser-surface-annealed AISI 304 stainless steel Part I: computer simulation

    International Nuclear Information System (INIS)

    Shiue, R.K.; Chang, C.T.; Young, M.C.; Tsay, L.W.

    2004-01-01

    The effect of residual thermal stresses on the fatigue crack growth of the laser-surface-annealed AISI 304 stainless steel, especially the effect of stress redistribution ahead of the crack tip was extensively evaluated in the study. Based on the finite element simulation, the longitudinal residual tensile stress field has a width of roughly 20 mm on the laser-irradiated surface and was symmetric with respect to the centerline of the laser-annealed zone (LAZ). Meanwhile, residual compressive stresses distributed over a wide region away from the LAZ. After introducing a notch perpendicular to the LAZ, the distribution of longitudinal residual stresses became unsymmetrical about the centerline of LAZ. High residual compressive stresses exist within a narrow range ahead of notch tip. The improved crack growth resistance of the laser-annealed specimen might be attributed to those induced compressive stresses. As the notch tip passed through the centerline of the LAZ, the residual stress ahead of the notch tip was completely reverted into residual tensile stresses. The existence of unanimous residual tensile stresses ahead of the notch tip was maintained, even if the notch tip extended deeply into the LAZ. Additionally, the presence of the residual tensile stress ahead of the notch tip did not accelerate the fatigue crack growth rate in the compact tension specimen

  9. Estimation and optimization of flank wear and tool lifespan in finish turning of AISI 304 stainless steel using desirability function approach

    Directory of Open Access Journals (Sweden)

    Lakhdar Bouzid

    2018-10-01

    Full Text Available The wear of cutting tools remains a major obstacle. The effects of wear are not only antagonistic at the lifespan and productivity, but also harmful with the surface quality. The present work deals with some machinability studies on flank wear, surface roughness, and lifespan in finish turning of AISI 304 stainless steel using multilayer Ti(C,N/Al2O3/TiN coated carbide inserts. The machining experiments are conducted based on the response surface methodology (RSM. Combined effects of three cutting parameters, namely cutting speed, feed rate and cutting time on the two performance outputs (i.e. VB and Ra, and combined effects of two cutting parameters, namely cutting speed and feed rate on lifespan (T, are explored employing the analysis of variance (ANOVA. The relationship between the variables and the technological parameters is determined using a quadratic regression model and optimal cutting conditions for each performance level are established through desirability function approach (DFA optimization. The results show that the flank wear is influenced principally by the cutting time and in the second level by the cutting speed. In addition, it is indicated that the cutting time is the dominant factor affecting workpiece surface roughness followed by feed rate, while lifespan is influenced by cutting speed. The optimum level of input parameters for composite desirability was found Vc1-f1-t1 for VB, Ra and Vc1-f1 for T, with a maximum percentage of error 6.38%.

  10. Analysis of correlations of multiple-performance characteristics for optimization of CO2 laser nitrogen cutting of AISI 304 stainless steel

    Directory of Open Access Journals (Sweden)

    Miloš Madić

    2014-07-01

    Full Text Available The identification of laser cutting conditions for satisfying different requirements such as improving cut quality characteristics and material removal rate is of great importance. In this paper, an attempt has been made to develop mathematical models in order to relate laser cutting parameters such as the laser power, cutting speed, assist gas pressure and focus position, and cut quality characteristics such as the surface roughness, kerf width and width of heat affected zone (HAZ. A laser cutting experiment was planned as per Taguchi’s L27 orthogonal array with three levels for each of laser cutting parameters considered. 3 mm thick AISI 304 stainless steel was used as workpiece material. Mathematical models were developed using a single hidden layer artificial neural network (ANN trained with the Levenberg– Marquardt algorithm. On the basis of the developed ANN models the effects of the laser cutting parameters on the cut quality characteristics were presented. It was observed that laser cutting parameters variously affect cut quality characteristics. Also, for the range of operating conditions considered in the experiment, laser cut quality operating diagrams were shown. From these operating diagrams one can see the values of cut quality characteristics that can be achieved and subsequently select laser cutting parameter values. Furthermore, the analysis includes correlations between cut quality characteristics and material removal rate. To this aim, six trade-off operating diagrams for improving multiple responses at the same time were given.

  11. Investigation of the influential parameters of machining of AISI 304 ...

    Indian Academy of Sciences (India)

    application of cutting fluid results in longer tool life and better surface finish. ... parameters for turning of AISI 304 stainless steel by considering the process ... In the design of experiments (DOE) the full factorial method was used in .... Esme U 2009 Application of Taguchi method for the optimization of resistance spot welding.

  12. Laser welding of NiTi shape memory alloy: Comparison of the similar and dissimilar joints to AISI 304 stainless steel

    Science.gov (United States)

    Mirshekari, G. R.; Saatchi, A.; Kermanpur, A.; Sadrnezhaad, S. K.

    2013-12-01

    The unique properties of NiTi alloy, such as its shape memory effect, super-elasticity and biocompatibility, make it ideal material for various applications such as aerospace, micro-electronics and medical device. In order to meet the requirement of increasing applications, great attention has been given to joining of this material to itself and to other materials during past few years. Laser welding has been known as a suitable joining technique for NiTi shape memory alloy. Hence, in this work, a comparative study on laser welding of NiTi wire to itself and to AISI 304 austenitic stainless steel wire has been made. Microstructures, mechanical properties and fracture morphologies of the laser joints were investigated using optical microscopy, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray diffraction analysis (XRD), Vickers microhardness (HV0.2) and tensile testing techniques. The results showed that the NiTi-NiTi laser joint reached about 63% of the ultimate tensile strength of the as-received NiTi wire (i.e. 835 MPa) with rupture strain of about 16%. This joint also enabled the possibility to benefit from the pseudo-elastic properties of the NiTi component. However, tensile strength and ductility decreased significantly after dissimilar laser welding of NiTi to stainless steel due to the formation of brittle intermetallic compounds in the weld zone during laser welding. Therefore, a suitable modification process is required for improvement of the joint properties of the dissimilar welded wires.

  13. Characterization of gold and nickel coating on AISI 304 stainless steel for use in the fabrication of current collector plates for fuel cells; Caracterizacion de recubrimientos de oro y niquel realizados sobre acero inoxidable AISI 304 para su empleo en la fabricacion de placas colectoras de corriente para celdas de combustible

    Energy Technology Data Exchange (ETDEWEB)

    Flores Hernandez, J. Roberto [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)] e-mail: jrflores@iie.org.mx; Aguilar Gama, M. Tulio [UNAM. Facultad de Quimica, Mexico D.F. (Mexico); Cano Castillo, Ulises; Albarran, Lorena [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico); Olvera, J. Carlos; Orozco, German [CIDETEQ, Pedro Escobedo, Queretaro (Mexico)

    2009-09-15

    Among the different components that compose fuel cell technology (MEA, bipolar plates, seals, etc.) current collector plates play an important role in the good performance of fuel cells, since they collect all of the current generated and distribute it to the external circuit. Therefore, the most important properties that the current collector plates should have are excellent conductivity and good resistance to the corrosive conditions present in the fuel cell. This document presents results obtained during the nickel and gold electrodeposition process on AISI 304 stainless steel and the morphology and thickness of each coating, their adhesion, hardness and conductivity values. Finally, results obtained during some of the electrochemical tests performed on the coatings are shown. [Spanish] De los diferentes componentes que integran la tecnologia de celdas de combustible (MEA's, placas bipolares, sellos, etc.), las placas colectoras de corriente tienen un importante rol en el buen desempeno de la celdas de combustibles, ya que en estas placas se colecta toda la corriente generada y se distribuye al circuito externo. Debido a esto, las propiedades mas importantes que deben tener las placas colectaras de corriente son: excelente conductividad y buena resistencia a las condiciones corrosivas presentes en la celda de combustible. En este documento se presentan los resultados obtenidos en el proceso de electrodeposicion de niquel y oro sobre acero inoxidable AISI 304, asi como la morfologia y el espesor de cada recubrimiento, sus valores de adherencia, dureza y conductividad. Finalmente se muestran tambien los resultados obtenidos de algunas pruebas electroquimicas a los que fueron sometidos los recubrimientos.

  14. The influence of plasma nitriding on the fatigue behavior of austenitic stainless steel types AISI 316 and AISI 304

    International Nuclear Information System (INIS)

    Varavallo, Rogerio; Manfrinato, Marcos Dorigao; Rossino, Luciana Sgarbi; Spinelli, Dirceu; Riofano, Rosamel Melita Munoz

    2010-01-01

    The plasma nitriding process has been used as an efficient method to optimize the surface properties of steel and alloy in order to increase their wear, fatigue and corrosion resistance. This paper reports on a study of the composition and influence of the nitrided layer on the high-cycle fatigue properties of the AISI 316 and 304 type austenitic stainless steels. Test specimens of AISI 316 and 304 steel were nitrided at 400 deg C for 6 hours under a pressure of 4.5 mbar, using a gas mixture of 80% volume of H 2 and 20% volume of N 2 . The rotary fatigue limit of both nitrided and non-nitrided steels was determined, and the effect of the treatment on the fatigue limit of the two steels was evaluated. The mechanical properties of the materials were evaluated based on tensile tests, and the nitrided layer was characterized by microhardness tests, scanning electron microscopy and X-ray diffraction. The resulting nitride layer showed high hardness and mechanical strength, increasing the fatigue limit of the nitrided material in comparison with the non-nitrided one. The fatigue limit of the 316 steel increased from 400 MPa to 510 MPa in response to nitriding, while that of the 304 steel increased from 380 MPa to 560 MPa. One of the contributing factors of this increase was the introduction of residual compressive stresses during the surface hardening process, which reduce the onset of crack formation underneath the nitride layer. (author)

  15. Gas tungsten arc welding and friction stir welding of ultrafine grained AISI 304L stainless steel: Microstructural and mechanical behavior characterization

    Energy Technology Data Exchange (ETDEWEB)

    Sabooni, S., E-mail: s.sabooni@ma.iut.ac.ir [Department of Materials Engineering, Isfahan University of Technology, 84156-83111 Isfahan (Iran, Islamic Republic of); Karimzadeh, F.; Enayati, M.H. [Department of Materials Engineering, Isfahan University of Technology, 84156-83111 Isfahan (Iran, Islamic Republic of); Ngan, A.H.W. [Department of Mechanical Engineering, The University of Hong Kong, Pokfulam Road, Hong Kong (China); Jabbari, H. [Department of Materials Engineering, Isfahan University of Technology, 84156-83111 Isfahan (Iran, Islamic Republic of)

    2015-11-15

    In the present study, an ultrafine grained (UFG) AISI 304L stainless steel with the average grain size of 650 nm was successfully welded by both gas tungsten arc welding (GTAW) and friction stir welding (FSW). GTAW was applied without any filler metal. FSW was also performed at a constant rotational speed of 630 rpm and different welding speeds from 20 to 80 mm/min. Microstructural characterization was carried out by High Resolution Scanning Electron Microscopy (HRSEM) with Electron Backscattered Diffraction (EBSD) and Transmission Electron Microscopy (TEM). Nanoindentation, microhardness measurements and tensile tests were also performed to study the mechanical properties of the base metal and weldments. The results showed that the solidification mode in the GTAW welded sample is FA (ferrite–austenite) type with the microstructure consisting of an austenite matrix embedded with lath type and skeletal type ferrite. The nugget zone microstructure in the FSW welded samples consisted of equiaxed dynamically recrystallized austenite grains with some amount of elongated delta ferrite. Sigma phase precipitates were formed in the region ahead the rotating tool during the heating cycle of FSW, which were finally fragmented into nanometric particles and distributed in the weld nugget. Also there is a high possibility that the existing delta ferrite in the microstructure rapidly transforms into sigma phase particles during the short thermal cycle of FSW. These suggest that high strain and deformation during FSW can promote sigma phase formation. The final austenite grain size in the nugget zone was found to decrease with increasing Zener–Hollomon parameter, which was obtained quantitatively by measuring the peak temperature, calculating the strain rate during FSW and exact examination of hot deformation activation energy by considering the actual grain size before the occurrence of dynamic recrystallization. Mechanical properties observations showed that the welding

  16. Improvement of pitting corrosion resistance of AISI 304L stainless steel by nano-pulsed laser surface melting

    International Nuclear Information System (INIS)

    Pacquentin, W.; Blanc, C.; Caron, N.; Thro, P.Y.; Cheniere, A.; Tabarant, M.; Moutiers, G.; Miserque, F.; Plouzennec, H.; Oltra, R.

    2013-01-01

    The stainless steel 304L is widely used, however, in particular conditions, it may be sensitive to pitting corrosion. Nano-pulsed laser surface melting is a surface treatment which allows improving the corrosion resistance of this steel. This treatment consists in focusing a laser beam on the surface of the material, involving its quite immediately melting through a few microns depth, then an ultra-fast solidification occurs with cooling rate about 1011 K/s. The laser parameters control the modifications of the physico-chemical properties. In particular, we studied the influence of the impacts overlap of an ytterbium laser-fiber on the corrosion resistance of a 304L stainless steel in conditions of an aerated and agitated solution of NaCl (concentration of 30 g/L). We obtained an increase of the pitting potential of 220 mV, highlighting an improvement of the corrosion resistance. The study of the chemical and structural modifications is not enough to explain the improvement of the corrosion resistance. Other phenomena must be taken into account, as the quality of the oxide layer, in terms of physico-chemical and mechanical properties. (authors)

  17. Aspects of dislocation substructures associated with the deformation stages of stainless steel AISI 304 at high temperatures

    International Nuclear Information System (INIS)

    Oliveira, J.L.L.; Reis Filho, J.A.B.S.; Almeida, L.H. de; Monteiro, S.N.

    1978-07-01

    The development of dislocation substrutures in type 304 austenitic stainless steel at high temperatures has been associated with the deformation stages through log dσ/d epsilon x log epsilon plots, which show the transition point independently. The mechanisms responsible for the Dynamic Strain Aging particulary the Portevin-LeChatelier effect were related to the appearence of the stages. The results indicate that the deformation stages can be divided into two distinct regions. Each one of these region show particular characteristics with respect to the stress level, transition point, developed substructure and type of crystalline defects interaction with dislocations. (Author) [pt

  18. Understanding the effect of uniaxial tensile strain on the early stages of sensitization in AISI 304 austenitic stainless steel

    Energy Technology Data Exchange (ETDEWEB)

    Chowdhury, P.S., E-mail: psc0126@gmail.com [Techno India Agartala, Maheshkhola, Agartala, West Tripura PIN – 799004 (India); Guchhait, S.K.; Mitra, P.K. [Department of Metallurgical and Material Engineering, Jadavpur University, Kolkata 700032 (India); Mukherjee, P.; Gayathri, N. [Variable Energy Cyclotron Centre (VECC), 1/AF Bidhan Nagar, Kolkata 700064 (India); Mitra, M.K. [Department of Metallurgical and Material Engineering, Jadavpur University, Kolkata 700032 (India)

    2015-04-01

    In the present study, an attempt has been made to understand the effect of different competing mechanisms controlling the overall degree of sensitization (DOS) of deformed austenitic stainless steel at the early stage of sensitization. The Double Loop Electrochemical Potentiokinetic Reactivation (DL-EPR) studies were performed to characterize the Degree of Sensitization (DOS) as a function of both pre-defined strain and sensitization temperature. X-ray Diffraction (XRD) and Scanning Electron Microscopy (SEM) were used to explain the phenomena qualitatively. A non monotonous behaviour in the variation of DOS has been observed with deformation and sensitization temperature. The presence of Deformation Induced Martensites (DIM) and their transformation into tempered martensites (α + M{sub 23}C{sub 6}) at higher temperatures was found to play major roles in controlling the overall sensitization and desensitization processes. - Highlights: • Interplay of various dynamic processes (four) in the early sensitization. • Deformation induced martensite (α′) playing major role at low temperature. • α (Tempered martensite) induced processes plays a vital role at higher temperatures. • Results in non monotonous variation in degree of sensitisation (DOS)

  19. Weldability of AISI 304 to copper by friction welding

    Energy Technology Data Exchange (ETDEWEB)

    Kirik, Ihsan [Batman Univ. (Turkey); Balalan, Zulkuf [Firat Univ., Elazig (Turkey)

    2013-06-01

    Friction welding is a solid-state welding method, which can join different materials smoothly and is excessively used in manufacturing industry. Friction welding method is commonly used in welding applications of especially cylindrical components, pipes and materials with different properties, for which other welding methods remain incapable. AISI 304 stainless steel and a copper alloy of 99.6 % purity were used in this study. This couple was welded in the friction welding machine. After the welding process, samples were analyzed macroscopically and microscopically, and their microhardness was measured. Tensile test was used to determine the bond strength of materials that were joined using the friction welding method. At the end of the study, it was observed that AISI 304 stainless steel and copper could be welded smoothly using the friction welding method and the bond strength is close to the tensile strength of copper. (orig.)

  20. Behavior to the fracture of an AISI 304 stainless steel sensitized in BWR reactor conditions (288 degrees Centigrade and 80 Kg/cm{sup 2}); Comportamiento a la fractura de un acero inoxidable AISI 304 sensibilizado en condiciones de reactor BWR (288 grados Centigrados y 80 Kg/cm{sup 2})

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez C, R.; Diaz S, A.; Garcia R, R.; Aguilar T, A.; Gachuz M, M.; Arganis J, C.; Merino C, J. [Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

    1999-07-01

    It is a knew fact that ductility of a lot of structural alloys can be deteriorated by the environment effect which are exposed, and that their consequent embrittlement can put in doubt the safety of their functioning; such is the case of austenitic stainless steels used in internal components of the BWR type reactors which not only is subjected to the effect combined of the aggressive environment which surround it (pressure, temperature, corrosion potential, conductivity medium, local state of efforts, etc.), but also to the action of present neutron radiation, manifesting microstructural changes which are reflected in the augmentation of its susceptibility to the intergranular cracking, phenomena generally known as IASCC ''Irradiation Assisted Stress Corrosion Cracking''. Once appeared the cracking in the material, the useful life of a component is limited by the rapidity to growth of these cracking, making necessary evaluations which can to predict its behavior, therefore the present work shows the preliminary results for determining the behavior to the fracture of an AISI 304 stainless steel sensitized, in a dynamic recirculation circuit which allows to simulate the operation conditions of a BWR reactor (288 Centigrade and 80 kg/cm{sup 2}). (Author)

  1. Analysis of AISI 304 Tensile Strength as an Anchor Chain of Mooring System

    Science.gov (United States)

    Hamidah, I.; Wati, R.; Hamdani, R. A.

    2018-05-01

    The background of this research is the use of mild steel (i.e., St37) as anchor chain that works on the corrosive environment of seawater which is possible to decrease its tensile strength. The longer soaked in seawater, the more significant the lowering of its tensile strength. Anchor chain needs to be designed by considering its tensile strength and corrosion resistance, so it’s able to support mooring system well. The primary purpose of this research is obtaining the decreasing of stainless steel 304 (AISI 304) tensile strength which is corroded by seawater as anchor chain of the mooring system. It is also essential to obtain the lifetime of AISI304 and St37 as anchor chain with the same load, the corrosion rate of AISI 304, and St 37 in seawater. The method which was employed in this research is an experiment with four pieces of stainless steel AISI 304, and of St 37 corrosion testing samples, six pieces of stainless steel 304, and six pieces of St 37 for tensile testing samples. The result of this research shows that seawater caused stainless steel AISI 304 as anchor chain has decreased of tensile strength about 1.68 % during four weeks. Also, it indicates that AISI 304 as anchor chain has a lifetime about 130 times longer than St 37. Further, we found that the corrosion rate of stainless steel 304 in seawater is 0.2042 mpy in outstanding category, while the St 37 samples reached up to 27.0247 mpy ranked as fair category. This result recommends that AISI 304 more excellence than St 37 as anchor chain of the mooring system.

  2. Friction and bending forces evaluation of AISI 304 DDQ steel sheet forming by bending tests under deep-drawing multiaxial stresses; Evaluacion de la fuerza de doblado y de friccion en el conformado de chapa de acero inoxidable AISI 304 DDQ mediante ensayos de doblado en condiciones multiaxiales de embuticion

    Energy Technology Data Exchange (ETDEWEB)

    Coello, J.; Miguel, V.; Ferrer, C.; Calatayud, A.; Martinez, A.

    2012-11-01

    Die radius is a critical area from the viewpoint of friction in forming processes. Moreover the sheet, that has been previously deformed in flange area, suffers bending and unbending stresses. Then, die-sheet contact in die radius must be especially considered in order to guarantee the suitable lubrication conditions. In the present work, a test method is carried out for evaluating an AISI 304 DDQ steel under similar conditions to those existing in the die radius area and that, usually, are not really reproduced in traditional bending under tensions tests. Deformation under pure shear condition, the bending and the radius angle have been established as variables of the tests. Results allow to obtain the apparent pressure sheet-bending tool, that increases with bending angle and decreases with tool radius. This last variable is the most significant while the bending angle has lesser influence. Although experimental results present some concordances with values obtained by analytical methods, some corrections must be considered in them in order to improve the theoretical values. (Author) 18 refs.

  3. Multiaxial fatigue criteria for AISI 304 and 2-1/4 Cr-1 Mo steel at 5380C with applications to strain-range partitioning and linear summation of creep and fatigue damage

    International Nuclear Information System (INIS)

    Blass, J.J.

    1982-01-01

    An improved multiaxial fatigue failure criterion was developed based on the results of combined axial-torsional strain cycling tests of AISI 304 and 2-1/4 Cr-1 Mo steel conducted at 538 0 C (1000 0 F). The formulation of this criterion involves the shear and normal components of inelastic strain range on the planes of maximum inelastic shear strain range. Optimum values of certain parameters contained in the formulation were obtained for each material by the method of least squares. The ability of this criterion to correlate the test results was compared with that of the usual (Mises) equivalent inelastic strain range criterion. An improved definition of equivalent inelastic strain range resulting from these considerations was used to generalize the theory of Strain Range Partitioning to multiaxial stress-strain conditions and was also applied to the linear summation of creep and fatigue damage

  4. Studies on the influence of metallurgical variables on the stress corrosion behavior of AISI 304 stainless steel in sodium chloride solution using the fracture mechanics approach

    International Nuclear Information System (INIS)

    Khatak, H.S.; Gnanamoorthy, J.B.; Rodriguez, P.

    1996-01-01

    Stress corrosion data on a nuclear grade AISI type 304 stainless steel in a boiling solution of 5M NaCl + 0.15M Na 2 SO 4 + 3 mL/L HCl (bp 381 K) for various metallurgical conditions of the steel are presented in this article. The metallurgical conditions used are solution annealing, sensitization, 10 pct cold work, 20 pct cold work, solution annealing + sensitization, 10 pct cold work + sensitization, and 20 pct cold work + sensitization. The fracture mechanics approach has been used to obtain quantitative data on the stress corrosion crack growth rates. The stress intensity factor, K I , and J integral, J I , have been used as evaluation parameters. The crack growth rates have been measured using compact tension type samples under both increasing and decreasing stress intensity factors. A crack growth rate of 5 x 10 -11 m/s was chosen for the determination of threshold parameters. Results of the optical microscopic and fractographic examinations are presented. Acoustic signals were recorded during crack growth. Data generated from acoustic emissions, activation energy measurements, and fractographic features indicate hydrogen embrittlement as the possible mechanism of cracking

  5. Initiation and growth of thermal fatigue crack networks in an AISI 304 L type austenitic stainless steel (X2 CrNi18-09)

    International Nuclear Information System (INIS)

    Maillot, V.

    2004-01-01

    We studied the behaviour of a 304 L type austenitic stainless steel submitted to thermal fatigue. Using the SPLASH equipment of CEA/SRMA we tested parallelepipedal specimens on two sides: the specimens are continuously heated by Joule effect, while two opposites faces are cyclically. cooled by a mixed spray of distilled water and compressed air. This device allows the reproduction and the study of crack networks similar to those observed in nuclear power plants, on the inner side of circuits fatigued by mixed pressurized water flows at different temperatures. The crack initiation and the network constitution at the surface were observed under different thermal conditions (Tmax = 320 deg C, ΔT between 125 and 200 deg C). The experiment produced a stress gradient in the specimen, and due to this gradient, the in-depth growth of the cracks finally stopped. The obtained crack networks were studied quantitatively by image analysis, and different parameters were studied: at the surface during the cycling, and post mortem by step-by-step layer removal by grinding. The maximal depth obtained experimentally, 2.5 mm, is relatively coherent with the finite element modelling of the SPLASH test, in which compressive stresses appear at a depth of 2 mm. Some of the crack networks obtained by thermal fatigue were also tested in isothermal fatigue crack growth under 4-point bending, at imposed load. The mechanisms of the crack selection, and the appearance of the dominating crack are described. Compared to the propagation of a single crack, the crack networks delay the propagation, depending on the severity of the crack competition for domination. The dominating crack can be at the network periphery, in that case it is not as shielded by its neighbours as a crack located in the center of the network. It can also be a straight crack surrounded by more sinuous neighbours. Indeed, on sinuous cracks, the loading is not the same all along the crack path, leading to some morphological

  6. Sintering, microstructure and properties of WC-AISI304 powder composites

    International Nuclear Information System (INIS)

    Marques, B.J.; Fernandes, C.M.; Senos, A.M.R.

    2013-01-01

    Highlights: ► Total replacement of Co binder by stainless steel AISI 304 in WC based composites. ► Processing conditions for WC–stainless steel composites. ► Mechanical behavior and oxidation resistance of WC–stainless steel composites. -- Abstract: Tungsten carbide–stainless steel (AISI 304) based composites were successfully prepared by powder metallurgy routes using vacuum sintering at a maximum temperature of 1500 °C. The effects of the binder amount (between 6 and 15 wt.%) on the phase composition, microstructure and mechanical properties, namely hardness and fracture toughness, were investigated. Appreciable amount of (M,W) 6 C up to 12 wt.% was detected, especially for the higher SS contents. However, a good compromise between toughness and hardness was observed. Besides that, improved oxidation resistance was noticed in WC–SS based composites compared with WC–Co composites. The results are discussed having in mind the correlation between chemical composition, phase composition, microstructure and mechanical behavior

  7. Metallographic observations of AISI 304 - copper dissimular joints

    International Nuclear Information System (INIS)

    Medeiros, R.C. de; Carvalho Perdigao, S. de

    1982-01-01

    The current work informs on the SMAW dissimilar joints embrittled by molten Copper. Bead on plate of that metal were deposited on four different base metals to evaluate the phenomena. Conventional and non conventional welding methods were employed to obtain dissimilar joints of AISI 304-Cu. The latter were observed metallographically. These results are to be complemented by mechanical testing actually being performed. (Author) [pt

  8. Initiation and growth of thermal fatigue crack networks in an AISI 304 L type austenitic stainless steel (X2 CrNi18-09); Amorcage et propagation de reseaux de fissures de fatigue thermique dans un acier inoxydable austenitique de type X2 CrNi18-09 (AISI 304 L)

    Energy Technology Data Exchange (ETDEWEB)

    Maillot, V

    2004-07-01

    We studied the behaviour of a 304 L type austenitic stainless steel submitted to thermal fatigue. Using the SPLASH equipment of CEA/SRMA we tested parallelepipedal specimens on two sides: the specimens are continuously heated by Joule effect, while two opposites faces are cyclically. cooled by a mixed spray of distilled water and compressed air. This device allows the reproduction and the study of crack networks similar to those observed in nuclear power plants, on the inner side of circuits fatigued by mixed pressurized water flows at different temperatures. The crack initiation and the network constitution at the surface were observed under different thermal conditions (Tmax = 320 deg C, {delta}T between 125 and 200 deg C). The experiment produced a stress gradient in the specimen, and due to this gradient, the in-depth growth of the cracks finally stopped. The obtained crack networks were studied quantitatively by image analysis, and different parameters were studied: at the surface during the cycling, and post mortem by step-by-step layer removal by grinding. The maximal depth obtained experimentally, 2.5 mm, is relatively coherent with the finite element modelling of the SPLASH test, in which compressive stresses appear at a depth of 2 mm. Some of the crack networks obtained by thermal fatigue were also tested in isothermal fatigue crack growth under 4-point bending, at imposed load. The mechanisms of the crack selection, and the appearance of the dominating crack are described. Compared to the propagation of a single crack, the crack networks delay the propagation, depending on the severity of the crack competition for domination. The dominating crack can be at the network periphery, in that case it is not as shielded by its neighbours as a crack located in the center of the network. It can also be a straight crack surrounded by more sinuous neighbours. Indeed, on sinuous cracks, the loading is not the same all along the crack path, leading to some

  9. The influence of Reynolds number on the galvanic corrosion of the copper/AISI 304 pair in aqueous LiBr solutions

    International Nuclear Information System (INIS)

    Montanes, M.T.; Sanchez-Tovar, R.; Garcia-Anton, J.; Perez-Herranz, V.

    2009-01-01

    The influence of Reynolds number on the galvanic corrosion of the copper/AISI 304 stainless steel pair in a concentrated lithium bromide solution was investigated according to the mixed potential theory. A hydraulic circuit was designed to study dynamic corrosion processes in situ. A potential relation between corrosion current density (i corr ) and Reynolds number (Re) was found for copper, showing a mixed control of a chemical step and mass transport through the corrosion products film with the predominance of the former. No dependence of i corr on Re could be established for AISI 304, showing a chemical step control. Moreover, under stagnant conditions, partial passivation may occur in AISI 304; however, under flowing conditions passivation is not possible. Copper is the anodic element of the pair under all flowing conditions analysed. The galvanic phenomenon is more important as Re increases, but the results show compatibility of both materials at all Re values analysed. Similarly, a potential relation between galvanic current density (i G ) and Re was found, showing a mixed control of a chemical step and mass transport with the predominance of the latter. Copper corrosion resistance decreases more rapidly as Re increases due to the AISI 304 galvanic effect: there is a synergy between the galvanic effect and the hydrodynamic conditions. Under stagnant conditions, the galvanic behaviour of the materials is close to the compatibility limit and an inversion of the anodic element of the galvanic pair takes place.

  10. Mechanical behavior of AISI 304SS determined by miniature test methods after neutron irradiation to 28 dpa

    Energy Technology Data Exchange (ETDEWEB)

    Rabenberg, Ellen M.; Jaques, Brian J. [Department of Materials Science and Engineering, Boise State University, 1910 University Dr., Boise, ID 83725 (United States); Center for Advanced Energy Studies, 995 University Blvd., Idaho Falls, ID 83401 (United States); Sencer, Bulent H. [Center for Advanced Energy Studies, 995 University Blvd., Idaho Falls, ID 83401 (United States); Idaho National Laboratory, Idaho Falls, ID 83415 (United States); Garner, Frank A. [Radiation Effects Consulting, 2003 Howell Ave., Richland, WA 99354 (United States); Freyer, Paula D. [Westinghouse Electric Company LLC, Pittsburgh, PA 15235 (United States); Okita, Taira [Research Into Artifacts Dept., Center for Engineering, University of Tokyo, Tokyo (Japan); Butt, Darryl P., E-mail: DarrylButt@BoiseState.edu [Department of Materials Science and Engineering, Boise State University, 1910 University Dr., Boise, ID 83725 (United States); Center for Advanced Energy Studies, 995 University Blvd., Idaho Falls, ID 83401 (United States)

    2014-05-01

    The mechanical properties of AISI 304 stainless steel irradiated for over a decade in the Experimental Breeder Reactor (EBR-II) were measured using miniature mechanical testing methods. The shear punch method was used to evaluate the shear strengths of the neutron-irradiated steel and a correlation factor was empirically determined to predict its tensile strength. The strength of the stainless steel slightly decreased with increasing irradiation temperature, and significantly increased with increasing dose until it saturated above approximately 5 dpa. An effective tensile strain hardening exponent was also obtained from the data which shows a relative decrease in ductility of steel with increased irradiation damage. Ferromagnetic measurements were used to observe and deduce the effects of the stress-induced austenite to martensite transformation as a result of shear punch testing.

  11. Inductive plasma source for the ion treatment of AISI-304 SS

    International Nuclear Information System (INIS)

    Piedad-Beneitez, A de la; Lopez-Callejas, R; Granda-Gutierrez, E E; Rodriguez-Mendez, B G; Perez-Martinez, J A; Flores-Fuentes, A A; Valencia-Alvarado, R; Barocio, S R; Mercado-Cabrera, A; Pena-Eguiluz, R; Munoz-Castro, A E

    2008-01-01

    The design and construction of a simple inductive plasma source is described as constituted by an evacuated Pyrex glass cylinder reactor with 190 mm inner diameter and 500 mm length. This discharge vessel is coaxially surrounded by a cylindrically wound antenna, 240 mm in diameter, made of 3.2 mm wide copper wire. The antenna is supplied by a 13.56 MHz RF generator whose resulting electric field is able to create the plasma. When nitrogen is admitted to the vessel, the plasma generation takes place within the 0.1-50 Pa work pressure and 300-600 W RF power. The plasma density has been established by double Langmuir probes between 3.2 x 10 15 and 2.4 x 10 18 m -3 . This inductive plasma set up is meant to modify the surface of AISI-304 stainless steel by means of ion deposition, thanks to the sample bias provided by an external - 400 V dc supply, in order to improve the steel hardness without compromising its corrosion resistance. Once accelerated by the negative bias, the plasma ions impinge on the sample nitriding it by diffusion. The treated samples were characterized by x-ray diffraction (XRD) indicating the formation of the expanded gamma phase, by scanning electron microscopy (SEM) providing the atomic percentages of nitrogen, and by microhardness (HV) measurement.

  12. Determination of the time to failure curve as a function of stress for a highly irradiated AISI 304 stainless steel after constant load tests in simulated PWR water environment

    International Nuclear Information System (INIS)

    Pokor, C.; Massoud, J.P.; Wintergerst, M.; Toivonen, A.; Ehrnsten, U.; Karlsen, W.

    2011-01-01

    The structures of Reactor Pressure Vessel Internals are subjected to an intense neutron flux. Under these operating conditions, the microstructure and the mechanical properties of the austenitic stainless steel components change. In addition, these components are subjected to stress of either manufacturing origin or generated under operation. Cases of baffle bolts cracking have occurred in CP0 Nuclear Power Plant units. The mechanism of degradation of these bolts is Irradiation-Assisted Stress Corrosion Cracking. In order to obtain a better understanding of this mechanism and its principal parameters of influence, a set of stress corrosion tests (mainly constant load tests) were launched within the framework of the EDF project 'PWR Internals' using materials from a Chooz A baffle corner (SA 304). These tests aim to quantify the influence on IASCC of the applied stress, temperature and environment (primary water, higher lithium concentration, inert environment) for an irradiation dose close to 30 dpa. A curve showing time to failure as a function of the stress was determined. The shape of this curve is consistent with the few data that are available in the literature. A stress threshold of about 50 % of the yield strength value at the test temperature has been determined, below which cracking in that environment seems impossible. After irradiation this material is sensitive to intergranular fracture in a primary environment, but also in an inert environment (argon) at 340 C. The tests also showed a negative effect of increased lithium concentration on the time to failure and on the stress threshold. (authors)

  13. Surface severe plastic deformation of AISI 304 via conventional shot peening, severe shot peening and repeening

    Energy Technology Data Exchange (ETDEWEB)

    Unal, Okan, E-mail: unalokan78@gmail.com [Mechanical Engineering Department, Bartın University, Bartın 74100 (Turkey); Varol, Remzi [Mechanical Engineering Department, Suleyman Demirel University, Isparta 32200 (Turkey)

    2015-10-01

    Highlights: • CSP and SSP treatments transform austenite to metastable martensite structure. • Nanograin layer thickness after CSP and SSP is 8 μm and 22 μm, respectively. • Shot peening leads to carbon segregation from coarse to nano grain layer. • Repeening is an effective way to reduce surface roughness. - Abstract: Air blast conventional shot peening (CSP), severe shot peening (SSP) and repeening (RP) as a severe plastic deformation applications on AISI 304 austenitic stainless steel is addressed. Shot peened specimens are investigated based on optical, FESEM and digital microscope. The investigations present the austenite transformation to metastable martensite via mechanical twinning due to plastic deformation with high strain rates. It is found that SSP induces thicker nanograin layer with compared to CSP. In XRD studies, the austenite peaks broaden by means of severe shot peening and FWHM increase reveals the grain size reduction below 25 nm regimes on the surface. In EDAX line analysis of CSP specimen, carbon content increase has been detected from deformed layer through the nanocrystalline layer then the content reduces. The carbon segregation takes place due to the energy level distinction between dislocations and Fe−C bonds. 3d contour digital microscope studies and roughness investigations reveal that SSP has deleterious side effect on the surface roughness and surface flatness. However, RP is an effective way to reduce the surface roughness to reasonable values.

  14. Some Temperature Effects on AISI-304 Nitriding in an Inductively Coupled RF Plasma

    International Nuclear Information System (INIS)

    Valencia-Alvarado, R.; Barocio, S. R.; Mercado-Cabrera, A.; Pena-Eguiluz, R.; Munoz-Castro, A. E.; Piedad-Beneitez, A. de la; Rosa-Vazquez, J. de la; Lopez-Callejas, R.; Godoy-Cabrera, O. G.

    2006-01-01

    Some recent results obtained from nitriding AISI 304 stainless steel samples, 1.2 cm in diameter and 0.5 cm thick are reported here in the case of an 85% hydrogen and 15% nitrogen mixture work gas. The process was carried out from 300 to 400 W for (13.56 MHz) inductively coupled plasma within a 60 cm long pyrex glass tube 3.5 cm in diameter where the samples were biased up to -300 V with respect to earth. The resulting hardness appears to be a function of the substrate temperature which varied from 200 deg. C at a 0 V bias to 550 deg. C at -300 V. The plasma density at 400 W reached 3x1010 cm-3 with a 4 eV electron temperature. Prior to nitriding, all the samples were polished with 0.05 μm diamond paste, leading to a 30 nm average roughness (Ra). After nitriding at -300 V, the Ra rose until ∼400 nm while hardness values of 1500 HV under 300 g loads were measured. X ray diffraction indicates that the extended phase amplitude (γN), Fe and Cr nitride depends on the substrate temperature

  15. Joining of Dissimilar alloy Sheets (Al 6063&AISI 304 during Resistance Spot Welding Process: A Feasibility Study for Automotive industry

    Directory of Open Access Journals (Sweden)

    Reddy Sreenivasulu

    2014-12-01

    Full Text Available Present design trends in automotive manufacture have shifted emphasis to alternative lightweight materials in order to achieve higher fuel efficiency and to bring down vehicle emission. Although some other joining techniques are more and more being used, spot welding still remains the primary joining method in automobile manufacturing so far. Spot welds for automotive applications should have a sufficiently large diameter, so that nugget pullout mode is the dominant failure mode. Interfacial mode is unacceptable due to its low load carrying and energy absorption capability. Strength tests with different static loading were performed in, to reveal the failure mechanisms for the lap-shear geometry and the cross-tension geometry. Based on the literature survey performed, venture into this work was amply motivated by the fact that a little research work has been conducted to joining of dissimilar materials like non ferrous to ferrous. Most of the research works concentrated on joining of different materials like steel to steel or aluminium alloy to aluminium alloy by resistance spot welding. In this work, an experimental study on the resistance spot weldability of aluminium alloy (Al 6063 and austenitic stainless steel (AISI304 sheets, which are lap joined by using a pedestal type resistance spot welding machine. Welding was conducted using a 45-deg truncated cone copper electrode with 10-mm face diameter. The weld nugget diameter, force estimation under lap shear test and T – peel test were investigated using digital type tensometer attached with capacitive displacement transducer (Mikrotech, Bangalore, Model: METM2000ER1. The results shows that joining of Al 6063 and AISI 304 thin sheets by RSW method are feasible for automotive structural joints where the loads are below 1000N act on them, it is observed that by increasing the spots per unit length, then the joint with standing strength to oppose failure is also increased linearly incase of

  16. Influence of Size on the Microstructure and Mechanical Properties of an AISI 304L Stainless Steel—A Comparison between Bulk and Fibers

    Directory of Open Access Journals (Sweden)

    Francisco J. Baldenebro-Lopez

    2015-01-01

    Full Text Available In this work, the mechanical properties and microstructural features of an AISI 304L stainless steel in two presentations, bulk and fibers, were systematically studied in order to establish the relationship among microstructure, mechanical properties, manufacturing process and effect on sample size. The microstructure was analyzed by XRD, SEM and TEM techniques. The strength, Young’s modulus and elongation of the samples were determined by tensile tests, while the hardness was measured by Vickers microhardness and nanoindentation tests. The materials have been observed to possess different mechanical and microstructural properties, which are compared and discussed.

  17. Mechanical behaviour of AISI 304/307 weldments creep tested at 7000C

    International Nuclear Information System (INIS)

    Pope, A.M.; Monteiro, S.N.; Silveira, T.L.

    Preliminary observations on the mechanical behavior of AISI 304/347 weldments creep tested at 700 0 C are presented. The results are compared with those of similar welded joints isothermally treated at the same temperature for different times. The peculiar aspects in the mechanical behavior are discussed based on precipitation reactions which occur in the joint materials [pt

  18. The LCF behaviour of SS AISI 304 in the temperature range between 450 deg. C and 850 deg. C in connection with life time predictions

    International Nuclear Information System (INIS)

    Bocek, M.; Petersen, C.; Schmitt, R.

    The lifetime in high amplitude strain cycling with tensional hold periods is analysed presuming that creep failure damage is life determining. The life fraction rule (LFR) is used to calculate the lifetime consumpted during the dwell period in strain controlled tests as well as during tensional hold time stress cycles. It follows from the present investigation that stress relaxation occurring during the strain hold periods has a dominant influence upon the lifetime. The damage in stress relaxation is calculated by means of the LFR and the results are compared to experiments conducted on Zircaloy-4 (T=600 deg. C) and the austenitic stainless steel Type AISI 304 (T=650 deg. C). From the very good agreement between both it is concluded that under the loading conditions considered, creep failure damage is the main life determining damage contribution. To investigate the contributions of creep and fatigue to failure damage stress controlled experiments were conducted on AISI 304 at 550 deg. C and 850 deg. C. Whereas at the lower temperature (T 0.6 Tsub(s)) the lifetime increased with decreasing R. Therefrom it is concluded that in the case considered for T>0.6 Tsub(s) fatigue damage is not lifetime determining. (author)

  19. Experimental investigation on mechanical and microstructural properties of AISI 304 to Cu joints by CO2 laser

    Directory of Open Access Journals (Sweden)

    Bikash Ranjan Moharana

    2016-06-01

    Full Text Available Aim of the present work is to investigate mechanical and metallurgical characteristics of continuous wave CO2 laser welded dissimilar couple of AISI 304 stainless steel and commercially pure copper sheets in autogenous mode. Metallurgical analysis of the fusion zone has been done to understand the mixing and solidification behavior. Macroscopic examination has been carried out to observe the macro-segregation pattern of Cu, Fe and Cr rich phases in different zones, and the thickness of HAZ was found to be around 10 µm. The micro-channels formed from the steel side to weld pool describe that the copper solidifies first and provides the nucleation surface for the residual melt to grow. These tubular micro-channels formed may be due to carbide precipitation. The EDS analysis conforms the well mixing of SS and Cu inside the weld pool. The mechanical properties in terms of tensile stress found up to 201 MPa and the fracture are obtained outside the weld zone. Microhardness measurements over the fusion zone have been done to understand the keyhole growth and quenching, solidification sequence and stress distribution over the full area.

  20. Impact of structure and morphology of nanostructured ceria coating on AISI 304 oxidation kinetics

    International Nuclear Information System (INIS)

    Aadhavan, R.; Suresh Babu, K.

    2017-01-01

    Highlights: • Ceria coating reduced the oxidation kinetics of AISI304 by 3–4 orders. • Lower deposition rate (0.1 Å/s) resulted in dense and uniform coating. • Substrate temperature of 100 °C provided coating with smaller crystallite size. • Surface morphology of the coating has strong influence in oxidation protection. - Abstract: Nanostructured ceria-based coatings are shown to be protective against high-temperature oxidation of AISI 304 due to the dynamics of oxidation state and associated defects. However, the processing parameters of deposition have a strong influence in determining the structural and morphological aspects of ceria. The present work focuses on the effect of variation in substrate temperature (50–300 °C) and deposition rate (0.1–50 Å/s) of ceria in electron beam physical vapour evaporation method and correlates the changes in structure and morphology to high-temperature oxidation protection. Unlike deposition rate, substrate temperature exhibited a profound influence on crystallite size (7–18 nm) and oxygen vacancy concentration. Upon isothermal oxidation at 1243 K for 24 h, bare AISI 304 exhibited a linear mass gain with a rate constant of 3.0 ± 0.03 × 10"−"3 kg"2 m"−"4 s"−"1 while ceria coating lowered the kinetics by 3–4 orders. Though the thickness of the coating was kept constant at 2 μm, higher deposition rate offered one order lower protection due to the porous nature of the coating. Variation in the substrate temperature modulated the porosity as well as oxygen vacancy concentration and displayed the best protection for coatings deposited at moderate substrate temperature. The present work demonstrates the significance of selecting appropriate processing parameters to obtain the required morphology for efficient high-temperature oxidation protection.

  1. Impact of structure and morphology of nanostructured ceria coating on AISI 304 oxidation kinetics

    Energy Technology Data Exchange (ETDEWEB)

    Aadhavan, R.; Suresh Babu, K., E-mail: sureshbabu.nst@pondiuni.edu.in

    2017-07-31

    Highlights: • Ceria coating reduced the oxidation kinetics of AISI304 by 3–4 orders. • Lower deposition rate (0.1 Å/s) resulted in dense and uniform coating. • Substrate temperature of 100 °C provided coating with smaller crystallite size. • Surface morphology of the coating has strong influence in oxidation protection. - Abstract: Nanostructured ceria-based coatings are shown to be protective against high-temperature oxidation of AISI 304 due to the dynamics of oxidation state and associated defects. However, the processing parameters of deposition have a strong influence in determining the structural and morphological aspects of ceria. The present work focuses on the effect of variation in substrate temperature (50–300 °C) and deposition rate (0.1–50 Å/s) of ceria in electron beam physical vapour evaporation method and correlates the changes in structure and morphology to high-temperature oxidation protection. Unlike deposition rate, substrate temperature exhibited a profound influence on crystallite size (7–18 nm) and oxygen vacancy concentration. Upon isothermal oxidation at 1243 K for 24 h, bare AISI 304 exhibited a linear mass gain with a rate constant of 3.0 ± 0.03 × 10{sup −3} kg{sup 2} m{sup −4} s{sup −1} while ceria coating lowered the kinetics by 3–4 orders. Though the thickness of the coating was kept constant at 2 μm, higher deposition rate offered one order lower protection due to the porous nature of the coating. Variation in the substrate temperature modulated the porosity as well as oxygen vacancy concentration and displayed the best protection for coatings deposited at moderate substrate temperature. The present work demonstrates the significance of selecting appropriate processing parameters to obtain the required morphology for efficient high-temperature oxidation protection.

  2. Comparative study of the microbiological corrosion among an AISI 304L and an API X65

    International Nuclear Information System (INIS)

    Diaz S, A.; Arganis J, C.; Luna C, P.; Carapia M, L.; Gonzalez F, E.

    2004-01-01

    Metallic samples of AISI 304L sensitized and API X65, were subjected to the action of an inoculated media with reductive sulphate microorganisms (SBR), carrying out electrochemical evaluations by means of the techniques of Polarization Resistance (RP), Tafel extrapolation (ET) and Electrochemical Noise (RE). The generated information was complemented with the analysis and diagnostic of the present damage in the surfaces exposed in both metals. The used electrochemical techniques allow to determine the corrosion velocities associated to each system, establishing that the uniform corrosion is not affected by the effect of the microorganisms; however, electrochemical noise, evidenced the formation of stings associated to the presence of bacteria. (Author)

  3. Swelling of AISI 304L in response to simultaneous variations in stress and displacement rate

    International Nuclear Information System (INIS)

    Porter, D.L.; Garner, F.A.

    1984-01-01

    The duration of the transient regime of neutron-induced swelling in annealed AISI 304L at 400 0 C is sensitive to both stress and displacement rate variations. The simultaneous application of both variables exerts a synergistic effect on the transient regime. The duration of this regime cannot be reduced below a required intrinsic exposure of approx. 10 dpa, however, which has been found to be characteristic of all Fe-Ni-Cr austenitic alloys. This is four times larger than that currently assumed in the stress-affected swelling equation for 20% cold-worked AISI 316

  4. Evaluation of the mechanical properties of SA 333 Gr.6, AISI 304 and Zr-2.5% Nb through Automated Ball Indentation (ABI) technique

    International Nuclear Information System (INIS)

    Balakrishnan, K.S.; Rath, B.N.; Shriwastaw, R.S.; Ramadasan, E.; Kulkarni, R.V.; Sahoo, K.C.

    2009-08-01

    Automated Ball Indentation (ABI) technique has been employed in evaluating the tensile property data on three materials, namely SA333 Gr.6 carbon steel (used as PHT piping), AISI 304 (used as calandria vessel) and Zr-2.5% Nb (used as coolant tube) in Pressurised Heavy Water Reactors (PHWRs) with a view to exploring the applicability of ABI technique in providing reliable mechanical property data. The exercise was carried out in cooperation with a second laboratory where conventional tension tests alone were conducted such that the output of the study could be independently monitored and evaluated in an unbiased manner. The results generated in the authors' laboratory were found to be fully in agreement with what were obtained through conventional tension tests. Thus the study has been successful in establishing the reliability of the data obtained through miniature route especially in the case of coolant tube which has immense applications. (author)

  5. Impact of structure and morphology of nanostructured ceria coating on AISI 304 oxidation kinetics

    Science.gov (United States)

    Aadhavan, R.; Suresh Babu, K.

    2017-07-01

    Nanostructured ceria-based coatings are shown to be protective against high-temperature oxidation of AISI 304 due to the dynamics of oxidation state and associated defects. However, the processing parameters of deposition have a strong influence in determining the structural and morphological aspects of ceria. The present work focuses on the effect of variation in substrate temperature (50-300 °C) and deposition rate (0.1-50 Å/s) of ceria in electron beam physical vapour evaporation method and correlates the changes in structure and morphology to high-temperature oxidation protection. Unlike deposition rate, substrate temperature exhibited a profound influence on crystallite size (7-18 nm) and oxygen vacancy concentration. Upon isothermal oxidation at 1243 K for 24 h, bare AISI 304 exhibited a linear mass gain with a rate constant of 3.0 ± 0.03 × 10-3 kg2 m-4 s-1 while ceria coating lowered the kinetics by 3-4 orders. Though the thickness of the coating was kept constant at 2 μm, higher deposition rate offered one order lower protection due to the porous nature of the coating. Variation in the substrate temperature modulated the porosity as well as oxygen vacancy concentration and displayed the best protection for coatings deposited at moderate substrate temperature. The present work demonstrates the significance of selecting appropriate processing parameters to obtain the required morphology for efficient high-temperature oxidation protection.

  6. Controlled dissolution of colossal quantities of nitrogen in stainless steel

    DEFF Research Database (Denmark)

    Christiansen, Thomas; Somers, Marcel A. J.

    2006-01-01

    The solubility of nitrogen in austenitic stainless steel was investigated thermogravimetrically by equilibrating thin foils of AISI 304 and AISI 316 in ammonia/hydrogen gas mixtures. Controlled dissolution of colossal amounts of nitrogen under metastable equilibrium conditions was realized...

  7. Oxidation behaviour at 1123 K of AISI 304-Ni/Al-Al2O3/TiO2 multilayer system deposited by flame spray

    Directory of Open Access Journals (Sweden)

    Cervera, I.

    2011-04-01

    Full Text Available The oxidation behaviour of alumina/titania (97/3, 87/13 and 60/40 ceramic coatings using a Ni-Al coupling layer was studied in a thermobalance. Both layers were deposited on an AISI 304 stainless steel base metal by the flame spray technique. The coated steel was heated from room temperature to 1,123 K at 40 K min –1, oxidized in air for 50 h, and then cooled to room temperature at 40 K min–1. The mass gain was mainly attributed to the oxidation of Ni-Al coupling layer. Kinetic laws, DW·S –1 (mg.mm–2 vs. time (hours were close to a parabolic plot for each sample. Surface composition of ceramic top layer and the cross section of multilayer system were analysed using a wide range of experimental techniques including Scanning Electron Microscopy (SEM, equipped with a link energy dispersive X-Ray spectroscopy (EDX and X-Ray diffraction (XRD before and after the oxidation process. Coatings 97/3 and 87/13 presented a stable structure after flame spray deposition and they did not evolve with the oxidation process, while most of the 60/40 coating changed to a metastable structure after deposition and to a more stable structure after oxidation with high micro-cracks content. SEM and EDX microanalysis of the cross-sections showed that significant oxidation and a weak intergranular precipitation had been produced in the coupling layer and on the stainless steel base metal, respectively.El comportamiento a oxidación de recubrimientos cerámicos alúmina/titania (97/3, 87/13, 60/40 usando una capa de anclaje Ni-Al se ha estudiado mediante una termobalanza. Ambas capas se han depositado sobre un acero inoxidable AISI 304 utilizando la técnica de proyección llama (FS. El acero recubierto se ha calentado desde la temperatura ambiente hasta 1.123 K a 40 K min–1, se ha oxidado al aire durante 50 h, y luego se ha enfriado hasta la temperatura ambiente a 40 K min–1. La ganancia en masa se atribuye a la oxidación de la capa de enganche Ni-Al. La cin

  8. Corrosion behavior of plasma sprayed hydroxyapatite and hydroxyapatite-silicon oxide coatings on AISI 304 for biomedical application

    International Nuclear Information System (INIS)

    Singh, Gurpreet; Singh, Hazoor; Sidhu, Buta Singh

    2013-01-01

    The objective of this study is to evaluate corrosion resistance of plasma sprayed hydroxyapatite (HA) and HA-silicon oxide (SiO 2 ) coated AISI 304 substrates. In HA-SiO 2 coatings, 10 wt% SiO 2 and 20 wt% SiO 2 was mixed with HA. The feedstock and coatings were characterized by X-ray diffraction and scanning electron microscopy/energy dispersive X-ray spectroscopy. The corrosion resistance was determined for the uncoated and coated samples. The corrosion resistance of the AISI 304 was found more after the deposition of the HA-SiO 2 coatings rather than HA coating and uncoated. All the coatings were crack free after 24 h dipping in Ringer's solution for electrochemical corrosion testing.

  9. Revisiting Formability and Failure of AISI304 Sheets in SPIF: Experimental Approach and Numerical Validation

    Directory of Open Access Journals (Sweden)

    Gabriel Centeno

    2017-11-01

    Full Text Available Single Point Incremental Forming (SPIF is a flexible and economic manufacturing process with a strong potential for manufacturing small and medium batches of highly customized parts. Formability and failure in SPIF have been intensively discussed in recent years, especially because this process allows stable plastic deformation well above the conventional forming limits, as this enhanced formability is only achievable within a certain range of process parameters depending on the material type. This paper analyzes formability and failure of AISI304-H111 sheets deformed by SPIF compared to conventional testing conditions (including Nakazima and stretch-bending tests. With this purpose, experimental tests in SPIF and stretch-bending were carried out and a numerical model of SPIF is performed. The results allow the authors to establish the following contributions regarding SPIF: (i the setting of the limits of the formability enhancement when small tool diameters are used, (ii the evolution of the crack when failure is attained and (iii the determination of the conditions upon which necking is suppressed, leading directly to ductile fracture in SPIF.

  10. Formation of abrasion-resistant coatings of the AlSiFe{sub x}Mny intermetallic compound type on the AISI 304L alloy

    Energy Technology Data Exchange (ETDEWEB)

    Martinez-Peralez, L. G.; Flores-Valdes, A.; Salinas-Rodriguez, A.; Ochoa-Palacios, R. M.; Toscano-giles, J. A.; Torres-Torres, J.

    2016-05-01

    The α-Al{sub 9}FeMnSi and α-Al{sub 9}FeMn{sub 2}Si intermetallics formed by reactive sintering of Al, Si, Mn, Fe, Cr and Ni powders have been used in AISI 304L steels to enhance microhardness. Processing variables of the reactive sintering treatment were temperature (600, 650, 700, 750 and 800 degree centigrade), pressure (5, 10 y 20 MPa) and holding time (3600, 5400 y 7200 seconds). Experimental results show that temperature is the most important variable affecting the substrate/coating formation, while pressure does not appear to have a significant effect. The results show the optimum conditions of the reactive sintering that favor the substrate/coating formation are 800 degree centigrade, 20 MPa and 7200 seconds. Under these conditions, the reaction zone between the substrate and coating is more compacted and well-adhered, with a microhardness of 1300 Vickers. The results of SEM and X-Ray diffraction confirmed the formation of β-Al{sub 9}FeMnSi and β-Al{sub 9}FeMn{sub 2}Si intermetallics in the substrate/coating interface as well as the presence of Cr and Ni, indicating diffusion of these two elements from the substrate to the interface. (Author)

  11. Comparative study of the microbiological corrosion among an AISI 304L and an API X65; Estudio comparativo de la corrosion microbiologica entre un AISI 304L y un API X65

    Energy Technology Data Exchange (ETDEWEB)

    Diaz S, A.; Arganis J, C.; Luna C, P.; Carapia M, L. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico); Gonzalez F, E. [ITT, Toluca, Estado de Mexico (Mexico)

    2004-07-01

    Metallic samples of AISI 304L sensitized and API X65, were subjected to the action of an inoculated media with reductive sulphate microorganisms (SBR), carrying out electrochemical evaluations by means of the techniques of Polarization Resistance (RP), Tafel extrapolation (ET) and Electrochemical Noise (RE). The generated information was complemented with the analysis and diagnostic of the present damage in the surfaces exposed in both metals. The used electrochemical techniques allow to determine the corrosion velocities associated to each system, establishing that the uniform corrosion is not affected by the effect of the microorganisms; however, electrochemical noise, evidenced the formation of stings associated to the presence of bacteria. (Author)

  12. SCC tests of AISI 304 and 316L type stainless steels in SCW conditions

    International Nuclear Information System (INIS)

    Novotny, R.; Prchal, D.; Debarberis, L.; Haehner, P.; Degmova, J.

    2008-01-01

    Full text of publication follows. Super Critical Water Reactors (SCWR) have been pre-selected as a one of the candidate concepts for the new generation of nuclear reactors in frame of Generation IV. Beside the design concept choice of construction materials is the most important question. Despite extensive research due to using various materials either in the conventional supercritical coal power plants or SCWO systems there is still missing knowledge about the properties of the materials in operational conditions of SCWR. That includes influence of irradiation and environment composition on chemistry of water especially process of radiolysis, mechanical properties of the materials and oxide films properties. The process of choice and testing of possible construction and fuel cladding materials are still under R and D (e.g. EU HPLWR project). Two types of tests were undertaken in SCW environment conditions (t = 600 deg C, p = 250 bar): U-bend specimens for constant displacement SCC tests and tensile specimens for SSRT tests. SSRT tests were carried out in SCW environment with different concentration of dissolved O 2 : 1, 10, 100, 20 ppb (±5 ppb) and with different displacement rates: 0.1, 1, 10 μm/min. In SCC test with LI-bend specimens different time expositions were carried out in two concentrations of dissolved O 2 : 0 and 200 ppb. Water chemistry was continually monitored by means of pH, conductivity and dissolved O 2 sensors. After the test the specimens were analysed by optical microscopy, SEM and XRD. (authors)

  13. Formation of abrasion-resistant coatings of the AlSiFexMny intermetallic compound type on the AISI 304L alloy

    Directory of Open Access Journals (Sweden)

    Martínez-Perales, Laura G.

    2016-03-01

    Full Text Available The α-Al9FeMnSi and β-Al9FeMn2Si intermetallics formed by reactive sintering of Al, Si, Mn, Fe, Cr and Ni powders have been used in AISI 304L steels to enhance microhardness. Processing variables of the reactive sintering treatment were temperature (600, 650, 700, 750 and 800 °C, pressure (5, 10 y 20 MPa and holding time (3600, 5400 y 7200 seconds. Experimental results show that temperature is the most important variable affecting the substrate/coating formation, while pressure does not appear to have a significant effect. The results show the optimum conditions of the reactive sintering that favor the substrate/coating formation are 800 °C, 20 MPa and 7200 seconds. Under these conditions, the reaction zone between the substrate and coating is more compacted and well-adhered, with a microhardness of 1300 Vickers. The results of SEM and X-Ray diffraction confirmed the formation of α-Al9FeMnSi and β-Al9FeMn2Si intermetallics in the substrate/coating interface as well as the presence of Cr and Ni, indicating diffusion of these two elements from the substrate to the interface.Los intermetálicos α-Al9FeMnSi y β-Al9FeMn2Si formados por sinterización reactiva de polvos Al, Si, Mn, Fe, Cr, Ni se han utilizado en aceros AISI 304L para mejorar la microdureza. Las variables de procesamiento de sinterización reactiva fueron temperatura (600, 650, 700, 750, y 800 °C, presión (5, 10 y 20 MPa y el tiempo de retención (3600, 5400 7200 segundos. Los resultados experimentales muestran que la temperatura es la variable más importante que afecta a la formación del sustrato/recubrimiento, mientras que la presión no parece tener un efecto significativo una influencia significativa. Los resultados muestran las condiciones óptimas de la sinterización reactiva que favorecen la formación del sustrato/recubrimiento a 800 °C, 20 MPa y 7200 segundos. En estas condiciones, la zona de reacción entre el sustrato y el recubrimiento es más compacta y bien

  14. Intergranular stress corrosion in soldered joints of stainless steel 304

    International Nuclear Information System (INIS)

    Zamora R, L.

    1994-01-01

    The intergranular stress cracking of welded joints of austenitic stainless steel, AISI 304, is a serious problem in BWR type reactors. It is associated with the simultaneous presence of three factors; stress, a critical media and sensibilization (DOS). EPR technique was used in order to verify the sensibilization degree in the base metal, and the zone affected by heat and welding material. The characterization of material was done. The objective of this work is the study of microstructure and the evaluation of EPR technique used for the determination of DOS in a welded plate of austenitic stainless steel AISI 304. (Author)

  15. Evaluación de la fuerza de doblado y de fricción en el conformado de chapa de acero inoxidable AISI 304 DDQ mediante ensayos de doblado en condiciones multiaxiales de embutición

    Directory of Open Access Journals (Sweden)

    Coello, J.

    2012-08-01

    Full Text Available Die radius is a critical area from the viewpoint of friction in forming processes. Moreover the sheet, that has been previously deformed in flange area, suffers bending and unbending stresses. Then, die-sheet contact in die radius must be especially considered in order to guarantee the suitable lubrication conditions. In the present work, a test method is carried out for evaluating an AISI 304 DDQ steel under similar conditions to those existing in the die radius area and that, usually, are not really reproduced in traditional bending under tensions tests. Deformation under pure shear condition, the bending and the radius angle have been established as variables of the tests. Results allow to obtain the apparent pressure sheet-bending tool, that increases with bending angle and decreases with tool radius. This last variable is the most significant while the bending angle has lesser influence. Although experimental results present some concordances with values obtained by analytical methods, some corrections must be considered in them in order to improve the theoretical values.

    El radio de entrada a la matriz se considera una de las zonas críticas en los procesos de conformado de chapa mediante embutición profunda. El análisis de la fuerza de fricción y de doblado existentes resulta importante para predecir el comportamiento de la chapa en dicha zona, así como para garantizar una lubricación adecuada a las condiciones de procesado. En el presente trabajo, se aplica un método de ensayo que evalúa las acciones en el proceso de doblado del acero AISI 304 DDQ bajo condiciones similares a las que sufre el material en los procesos de embutición y que no son reproducidas por los clásicos ensayos de doblado bajo tensión. Se establecen como variables la deformación experimentada previamente por el material en condiciones típicas de cortante puro, “pure shear”, el ángulo de doblado y el radio de doblado. Los resultados obtenidos

  16. MICROSTRUCTURE AND FATIGUE PROPERTIES OF DISSIMILAR SPOT WELDED JOINTS OF AISI 304 AND AISI 1008

    Directory of Open Access Journals (Sweden)

    Nachimani Charde

    2013-06-01

    Full Text Available Carbon steel and stainless steel composites are being more frequently used for applications requiring a corrosion resistant and attractive exterior surface and a high strength structural substrate. Spot welding is a potentially useful and efficient jointing process for the production of components consisting of these two materials. The spot welding characteristics of weld joints between these two materials are discussed in this paper. The experiment was conducted on dissimilar weld joints using carbon steel and 304L (2B austenitic stainless steel by varying the welding currents and electrode pressing forces. Throughout the welding process; the electrical signals from the strain sensor, current transducer and terminal voltage clippers are measured in order to understand each and every millisecond of the welding process. In doing so, the dynamic resistances, heat distributions and forging forces are computed for various currents and force levels within the good welds’ regions. The other process controlling parameters, particularly the electrode tip and weld time, remained constant throughout the experiment. The weld growth was noted for the welding current increment, but in the electrode force increment it causes an adverse reaction to weld growth. Moreover, the effect of heat imbalance was clearly noted during the welding process due to the different electrical and chemical properties. The welded specimens finally underwent tensile, hardness and metallurgical testing to characterise the weld growth.

  17. Mechanical and Microstructural Properties of Friction Welded AISI 304 Stainless Steel to AISI 1060 Steel AISI 1060

    Directory of Open Access Journals (Sweden)

    Ates H.

    2014-10-01

    Full Text Available Rotary Friction welding is one of the most popular methods of joining similar and dissimilar materials. It is widely used with metals and thermoplastics in a wide variety of aviation, transport and aerospace industrial component designs. This study investigates the influence of friction and upsetting pressures on the hardness, tensile properties and microstructure of the welds. The experimental results showed that as the friction and upsetting pressures increased, the hardness and tensile strength values increased, as well. The tensile fracture of welded joint occurred in the AISI 1060 side. The friction processed joints were evaluated for their integrity and quality aspects by optical and scanning electron microscopy. For the perfect interfacial bonding, sufficient upsetting and friction pressures are necessary to reach the optimal temperature and severe plastic deformation to bring these materials within the attraction range.

  18. Study of the polarization for Incoloy 800 and for the stainless stell AISI 304 in mixtures of Iron, Nickel and Chromium Chlorides

    International Nuclear Information System (INIS)

    Travalloni, A.M.; Sathler, L.; Mattos, O.R.

    1985-01-01

    Polarization curves for the Incoloy 800 and for the stainless stell AISI 304 were obtained with static and rotational electrodes. The electrolytes employed showed growing concentrations of mixtures as Iron, Nickel and Chromium Chlorides their proportion being the same as the content of these elements in the respective alloys. The alloys under investigation exhibited a continuous transition behaviour from the passive to the active-passive and to the active conditions. Also, the pH was found the main parameter controlling the anodic behaviour of the alloy. (Author) [pt

  19. High temperature oxidation behavior of AISI 304L stainless steel—Effect of surface working operations

    International Nuclear Information System (INIS)

    Ghosh, Swati; Kumar, M. Kiran; Kain, Vivekanand

    2013-01-01

    Highlights: ► Surface working resulted in thinner oxide on the surface. ► Oxides on machined/ground surfaces richer in Cr, higher in specific resistivity. ► Additional ionic transport process at the metal-oxide for ground sample established. ► Presence of fragmented grains and martensite influenced oxide nature/morphology. - Abstract: The oxidation behavior of grade 304L stainless steel (SS) subjected to different surface finishing (machining and grinding) operations was followed in situ by contact electric resistance (CER) and electrochemical impedance spectroscopy (EIS) measurements using controlled distance electrochemistry (CDE) technique in high purity water (conductivity −1 ) at 300 °C and 10 MPa in an autoclave connected to a recirculation loop system. The results highlight the distinct differences in the oxidation behavior of surface worked material as compared to solution annealed material in terms of specific resistivity and low frequency Warburg impedance. The resultant oxide layer was characterized for (a) elemental analyses by glow discharge optical emission spectroscopy (GDOES) and (b) morphology by scanning electron microscopy (SEM). Oxide layers with higher specific resistivity and chromium content were formed in case of machined and ground conditions. Presence of an additional ionic transport process has also been identified for the ground condition at the metal/oxide interface. These differences in electrochemical properties and distinct morphological features of the oxide layer as a result of surface working were attributed to the prevalence of heavily fragmented grain structure and presence of martensite.

  20. Cooper coatings on stainless steel by laser cladding

    International Nuclear Information System (INIS)

    Reis, M.; Estanislau, S.; Cabral, A.; Pecas, P.; Gouveia, H.

    1998-01-01

    Copper laser cladding was performed on AISI 304L stainless steel. Some process parameters like process speed and focal point were analysed and it was established its influence on the quality of the coating. Simple track coating were achieved with good aspect, good adherence and good surface finishing. Therefore a reference basis for further developments related to industrial application, was created. (Author) 14 refs

  1. Intergranular stress corrosion in soldered joints of stainless steel 304.; Corrosion intergranular bajo esfuerzo en uniones soldadas de acero inoxidable 304

    Energy Technology Data Exchange (ETDEWEB)

    Zamora R, L [Instituto Nacional de Investigaciones Nucleares, Mexico City (Mexico)

    1994-12-31

    The intergranular stress cracking of welded joints of austenitic stainless steel, AISI 304, is a serious problem in BWR type reactors. It is associated with the simultaneous presence of three factors; stress, a critical media and sensibilization (DOS). EPR technique was used in order to verify the sensibilization degree in the base metal, and the zone affected by heat and welding material. The characterization of material was done. The objective of this work is the study of microstructure and the evaluation of EPR technique used for the determination of DOS in a welded plate of austenitic stainless steel AISI 304. (Author).

  2. Laser surface alloying of AISI 304 stainless steel with WC+Co+NiCr for improving wear resistance

    CSIR Research Space (South Africa)

    Chakraborty, A

    2017-01-01

    Full Text Available the surface using a 5kW continuous wave (CW) Nd:YAG laser at a beam diameter of 4mm, with the output power ranging from 1-3kW and scan speed from 0.005 m/s to 0.1 m/s by simultaneous feeding of precursor powder at a flow rate of 20mg/s using Ar shroud at a gas...

  3. On the Electrochemical Behavior of PVD Ti-Coated AISI 304 Stainless Steel in Borate Buffer Solution

    Science.gov (United States)

    Fattah-alhosseini, Arash; Elmkhah, Hassan; Attarzadeh, Farid Reza

    2017-04-01

    This work aims at studying the electrochemical behavior of annealed pure titanium (Ti) and nano-structured (NS) Ti coating in borate buffer solutions. Cathodic arc evaporation was successfully applied to deposit NS Ti coating. Samples were characterized by means of scanning electron microscope and x-ray diffraction. Potentiodynamic polarization tests, electrochemical impedance spectroscopy, and Mott-Schottky analysis were employed to discuss the electrochemical behavior of samples thoroughly. Electrochemical measurements showed that the deposited NS Ti coating offers a superior passivity in borate buffer solutions of pH 9.0 and 9.5. Mott-Schottky analysis revealed that all passive films are of n-type semiconducting nature in these alkaline solutions and the deposition process did not alter the semiconducting type of passive films formed on samples. Additionally, this analysis showed that the NS Ti coating possessed lower levels of donor densities. Finally, all electrochemical tests showed that passive behavior of the NS Ti samples was superior, mainly due to the formation of thicker and less defective passive films.

  4. Corrosion Of Stainless Steel With A Laser Bar Code In A Saline Solution

    OpenAIRE

    Domingues S.R.; Proenca M.B.; Ierardi M.C.F.; Freire C.M.A.

    1996-01-01

    The corrosion of stainless steel AISI 304 L plates marked by laser beam fusion is studied. The electrochemical experiments are carried out in 3.5% NaCl water solution. Electrochemical curves are obtained by potentiodynamic method. Sample surfaces are also examined by scanning electron microscopy. The changes of corrosion resistance after laser treatment are insignificant.

  5. Evaluación del comportamiento estructural y de resistencia a la corrosión de armaduras de acero inoxidable austenítico AISI 304 y dúplex AISI 2304 embebidas en morteros de cemento Pórtland

    Directory of Open Access Journals (Sweden)

    Medina, E.

    2012-12-01

    Full Text Available The mechanical and structural behaviour of two stainless steels reinforcements, with grades austenitic EN 1.4301 (AISI 304 and duplex EN 1.4362 (AISI 2304 have been studied, and compared with the conventional carbon steel B500SD rebar. The study was conducted at three levels: at rebar level, at section level and at structural element level. The different mechanical properties of stainless steel directly influence the behaviour at section level and structural element level. The study of the corrosion behaviour of the two stainless steels has been performed by electrochemical measurements, monitoring the corrosion potential and the lineal polarization resistance (LPR, of reinforcements embedded in ordinary Portland cement (OPC mortar specimens contaminated with different amount of chloride over one year time exposure. Both stainless steels specimens embedded in OPC mortar remain in the passive state for all the chloride concentration range studied after one year exposure.

    Se ha evaluado el comportamiento mecánico y estructural de dos aceros inoxidables corrugados, el austenítico EN 1.4301 (AISI 304 y el dúplex EN 1.4362 (AISI 2304, y se han comparado con el tradicional acero al carbono B500SD. El estudio se ha realizado en tres niveles: a nivel de barra, de sección y de pieza. Las diferentes características mecánicas de los aceros inoxidables condicionan el comportamiento a nivel de sección y de pieza estructural. El estudio del comportamiento frente a la corrosión de los dos aceros inoxidables se ha realizado mediante mediciones electroquímicas monitorizando el potencial de corrosión y la resistencia de polarización de armaduras embebidas en probetas de mortero contaminado con diferentes concentraciones de cloruros durante un tiempo de exposición de un año. Ambos aceros inoxidables permanecen en estado pasivo en las probetas para todos los contenidos de cloruros.

  6. Strengthening of stainless steel weldment by high temperature precipitation

    Directory of Open Access Journals (Sweden)

    Sergio Neves Monteiro

    2017-10-01

    Full Text Available The mechanical behavior and the strengthening mechanism of stainless steel welded joints at 600 °C have been investigated. The welds were composed of AISI 304 stainless steel, as base metal, and niobium containing AISI 347 stainless steel, as weld metal. The investigation was conducted by means of creep tests. The welded specimens were subjected to both high temperature (600 °C and long periods (up to 2000 h under constant load, and both mechanical properties and microstructural changes in the material were monitored. It was found that the exposure of the material at 600 °C under load contributes to a strengthening effect on the weld. The phenomenon might be correlated with an accelerated process of second phase precipitation hardening. Keywords: Stainless steel, Weld, AISI 304, Precipitation hardening

  7. Biofilm formation by Listeria monocytogenes on stainless steel surface and biotransfer potential

    OpenAIRE

    Oliveira,Maíra Maciel Mattos de; Brugnera,Danilo Florisvaldo; Alves,Eduardo; Piccoli,Roberta Hilsdorf

    2010-01-01

    An experimental model was proposed to study biofilm formation by Listeria monocytogenes ATCC 19117 on AISI 304 (#4) stainless steel surface and biotransfer potential during this process. In this model, biofilm formation was conducted on the surface of stainless steel coupons, set on a stainless steel base with 4 divisions, each one supporting 21 coupons. Trypic Soy Broth was used as bacterial growth substrate, with incubation at 37 ?C and stirring of 50 rpm. The number of adhered cells was de...

  8. Joining uranium to steel

    International Nuclear Information System (INIS)

    Perkins, M.A.

    1976-05-01

    A method has been devised which will allow the joining of uranium to steel by fusion welding through the use of an intermediate material. Uranium-0.5 titanium was joined to AISI 304L stainless steel by using a vanadium insert. Also, a method is now available for selecting possible filler metals when two entirely dissimilar metals need to be joined. This method allows a quantitative ranking to be made of the possible filler metals and thus the most likely candidate can be selected

  9. Failure of Stainless Steel Welds Due to Microstructural Damage Prevented by In Situ Metallography

    Directory of Open Access Journals (Sweden)

    Juan Manuel Salgado Lopez

    Full Text Available Abstract In stainless steels, microstructural damage is caused by precipitation of chromium carbides or sigma phase. These microconstituents are detrimental in stainless steel welds because they lead to weld decay. Nevertheless, they are prone to appear in the heat affected zone (HAZ microstructure of stainless steel welds. This is particularly important for repairs of industrial components made of austenitic stainless steel. Non-destructive metallography can be applied in welding repairs of AISI 304 stainless steel components where it is difficult to ensure that no detrimental phase is present in the HAZ microstructure. The need of microstructural inspection in repairs of AISI 304 is caused because it is not possible to manufacture coupons for destructive metallography, with which the microstructure can be analyzed. In this work, it is proposed to apply in situ metallography as non-destructive testing in order to identify microstructural damage in the microstructure of AISI 304 stainless steel welds. The results of this study showed that the external surface micrographs of the weldment are representative of HAZ microstructure of the stainless steel component; because they show the presence of precipitated metallic carbides in the grain boundaries or sigma phase in the microstructure of the HAZ.

  10. Development of austenitic stainless steel tubes for nuclear reactor cladding

    International Nuclear Information System (INIS)

    Padilha, A.F.; Ferreira, P.I.; Andrade, P.I.; Andrade, A.H.P. de; Meyerhof, S.; Mauricio, J.

    1984-01-01

    In the development of thin wall tubes for nuclear reactor fuel cladding applications, a great number of activities, related to the fabrication process as the qualification are involved. A test program was envisaged to verify the quality of seam welded stainless steel tubes (AISI 304), obtained as a result of an effort by the IPEN-CNEN/SP and the brazilian industry. The relevant aspects involved in the preparation of the tubes and some preliminary test results are presented. (Author) [pt

  11. Experimental characterization of nanoparticles emissions during Laser Shock Processing of AA6061, AISI304 and Ti6Al4V

    Directory of Open Access Journals (Sweden)

    João F. Gomes

    2017-11-01

    Full Text Available This paper describes an experimental study on the emission of nanometric size particles during laser shock processing of metallic materials: stainless steel, aluminum and titanium alloys which are the most common ones processed by this technique. The emission of nanometric size particles was confirmed to consist of aggregates composed of smaller spherical particles in the range of 10-20 nm, covered by a small concentric “layer” probably of metal oxides. The analysis of the nanoparticles showed the presence of the main elements present in the tested alloys as well as high oxygen content, which is another indication of the presence of oxides of Fe, Al and Ti. The amount of emitted nanoparticles, showed considerable increases over the baseline measured for the working environment, and these increases correspond to the more intense pulses of the laser beam. The material density was seen to highly affect the quantity of emitted nanoparticles. During LSP of aluminium alloy (the lighter material a large quantity of nanoparticles was measured, while in LSP of stainless steel few nanoparticles were observed, and this is the denser material, among the three tested. Titanium alloy results in intermediate values. The study of these emissions is innovative and relevant for industrial environments where the manufacturing process is in use.

  12. Time dependence of the natural passivation process on AISI 304 in an alkaline medium: Atomic force microscopy and scanning Kelvin probe force microscopy as additional tools to electrochemical impedance spectroscopy

    Science.gov (United States)

    Benaioun, N. E.; Maafa, I.; Florentin, A.; Denys, E.; Hakiki, N. E.; Moulayat, N.; Bubendorff, J. L.

    2018-04-01

    Thin surface films formed on AISI 304 samples in an alkaline solution of pH = 13 are studied by atomic force microscopy (AFM), scanning Kelvin probe force microscopy (SKPFM) and electrochemical impedance spectroscopy (EIS) as a function of immersion time. The results reveal that changes on EIS diagrams correspond to topographical modifications on the sample surface as shown by AFM. Both techniques are therefore complementary. The oxide layer is chemically homogenous as shown by SKPFM imaging and our ultra-thin passive layer is an efficient barrier against corrosion.

  13. The effect of sulphite on crevice corrosion and pitting on various steels in 0.5 M sodium chloride

    International Nuclear Information System (INIS)

    Hemmingsen, T.; Nielsen, L.V.; Maahn, E.

    1992-01-01

    A carbon steel, st 37, and two stainless steels, AISI 304 SS and AISI 316 SS were exposed to 0.5 M NaCl with 10 mM sulphite under anaerobic conditions. The sulphite ions may, under these conditions, be reduced to sulphide ions, and cause pitting or crevice corrosion. Electrochemical and bottle-test experiments were done to determine the effect of the sulphite addition. These effects were highly dependant on the pH

  14. Special stainless steels for sea water service

    International Nuclear Information System (INIS)

    Tomaselli, A.C.

    1983-01-01

    Very exacting demands are made on the corrosion resistance and mechanical properties of materials which in their service come into contact with seawater, and in many cases simultaneously with corrosive process solutions. The demand for higher alloy stainless steels for seawater application is rising in pace with the increasing requirements for safety and operation economy. The corrosion conditions in seawater and the resistance of stainless steels in this medium will be dealt with in the following. Sanicro 28 will then be compared with stainless steels, types AISI 304, 316 and 317, as well as with Alloy 20, Alloy 825 and SANDVIK 2RK65. (Author) [pt

  15. An X-ray diffraction study of microstructural deformation induced by cyclic loading of selected steels

    International Nuclear Information System (INIS)

    Fourspring, P.M.; Pangborn, R.N.

    1996-06-01

    X-ray double crystal diffractometry (XRDCD) was used to assess cyclic microstructural deformation in a face centered cubic (fcc) steel (AISI304) and a body centered cubic (bcc) steel (SA508 class 2). The first objective of the investigation was to determine if XRDCD could be used to effectively monitor cyclic microstructural deformation in polycrystalline Fe alloys. A second objective was to study the microstructural deformation induced by cyclic loading of polycrystalline Fe alloys. The approach used in the investigation was to induce fatigue damage in a material and to characterize the resulting microstructural deformation at discrete fractions of the fatigue life of the material. Also, characterization of microstructural deformation was carried out to identify differences in the accumulation of damage from the surface to the bulk, focusing on the following three regions: near surface (0--10 microm), subsurface (10--300 microm), and bulk. Characterization of the subsurface region was performed only on the AISI304 material because of the limited availability of the SA508 material. The results from the XRDCD data indicate a measurable change induced by fatigue from the initial state to subsequent states of both the AISI304 and the SA508 materials. Therefore, the XRDCD technique was shown to be sensitive to the microstructural deformation caused by fatigue in steels; thus, the technique can be used to monitor fatigue damage in steels. In addition, for the AISI304 material, the level of cyclic microstructural deformation in the bulk material was found to be greater than the level in the near surface material. In contrast, previous investigations have shown that the deformation is greater in the near surface than the bulk for Al alloys and bcc Fe alloys

  16. Influence of Plastic Deformation on Low Temperature Surface Hardening of Austenitic Stainless Steel by Gaseous Nitriding

    DEFF Research Database (Denmark)

    Bottoli, Federico; Winther, Grethe; Christiansen, Thomas Lundin

    2015-01-01

    This article addresses an investigation of the influence of plastic deformation on low temperature surface hardening by gaseous nitriding of two commercial austenitic stainless steels: AISI 304 and EN 1.4369. The materials were plastically deformed to different equivalent strains by uniaxial...... demonstrate that a case of expanded austenite develops and that, in particular, strain-induced martensite has a large influence on the nitrided zone....

  17. Analysis of the austenitic stainless steel's r-value behavior at elevated temperatures

    OpenAIRE

    Dušan Arsić; Milan Djordjević; Srbislav Aleksandrović; Vukić Lazić; Ruzica R. Nikolic; Branislav Hadzima

    2015-01-01

    An analysis of the anisotropy properties of austenitic steel AISI 304 (X5CrNi18-10) at elevated temperatures is presented in this paper. Considerations of the anisotropy problems are presented in the theoretical part of the paper, as well as the procedure for determination of the normal anisotropy coefficient. The experimental part of the paper describes the plan, methodology and equipment for testing of material's normal anisotropy and mechanical characteristics. The objective of conducting ...

  18. Corrosion behavior of stainless steel in bio diesel production; Comportamento quanto a corrosao de acos inoxidaveis na producao do biodiesel

    Energy Technology Data Exchange (ETDEWEB)

    Miranda, E.F. de [ArcelorMittal Sao Paulo Servicos, SP (Brazil); Moreira, M.C.; Lebrao, S.M.G. [Centro Universitario do Instituto Maua de Tecnologia, Sao Paulo, SP (Brazil)], e-mail: susana.lebrao@maua.br

    2010-07-01

    Biodiesel has become more attractive due to the benefits to the environment, mainly because it is a renewable resource. However, the main barrier to biodiesel is it cost. One factor which is charged to marketing is the use of stainless steel throughout the production line, the most used is AISI 304. To evaluate more economical stainless steels, weight loss and stress corrosion tests were performed on samples of AISI 304 and 439 in methanol PS X30% sodium methylate solution, crude soybean oil, glycerol and biodiesel for about two hundred and fifty days. The mass loss was negligible, and there was complete absence of pitting and stress corrosion cracking in all media studied, showing that both alloys are suitable for the manufacture of such equipment. (author)

  19. Diamond deposition on siliconized stainless steel

    International Nuclear Information System (INIS)

    Alvarez, F.; Reinoso, M.; Huck, H.; Rosenbusch, M.

    2010-01-01

    Silicon diffusion layers in AISI 304 and AISI 316 type stainless steels were investigated as an alternative to surface barrier coatings for diamond film growth. Uniform 2 μm thick silicon rich interlayers were obtained by coating the surface of the steels with silicon and performing diffusion treatments at 800 deg. C. Adherent diamond films with low sp 2 carbon content were deposited on the diffused silicon layers by a modified hot filament assisted chemical vapor deposition (HFCVD) method. Characterization of as-siliconized layers and diamond coatings was performed by energy dispersive X-ray analysis, scanning electron microscopy, X-ray diffraction and Raman spectroscopy.

  20. Microstructure and Deformation Response of TRIP-Steel Syntactic Foams to Quasi-Static and Dynamic Compressive Loads

    Science.gov (United States)

    Ehinger, David; Weise, Jörg; Baumeister, Joachim; Funk, Alexander; Krüger, Lutz; Martin, Ulrich

    2018-01-01

    The implementation of hollow S60HS glass microspheres and Fillite 106 cenospheres in a martensitically transformable AISI 304L stainless steel matrix was realized by means of metal injection molding of feedstock with varying fractions of the filler material. The so-called TRIP-steel syntactic foams were studied with respect to their behavior under quasi-static compression and dynamic impact loading. The interplay between matrix material behavior and foam structure was discussed in relation to the findings of micro-structural investigations, electron back scatter diffraction EBSD phase analyses and magnetic measurements. During processing, the cenospheres remained relatively stable retaining their shape while the glass microspheres underwent disintegration associated with the formation of pre-cracked irregular inclusions. Consequently, the AISI 304L/Fillite 106 syntactic foams exhibited a higher compression stress level and energy absorption capability as compared to the S60HS-containing variants. The α′ -martensite kinetic of the steel matrix was significantly influenced by material composition, strain rate and arising deformation temperature. The highest ferromagnetic α′-martensite phase fraction was detected for the AISI 304L/S60HS batches and the lowest for the TRIP-steel bulk material. Quasi-adiabatic sample heating, a gradual decrease in strain rate and an enhanced degree of damage controlled the mechanical deformation response of the studied syntactic foams under dynamic impact loading. PMID:29695107

  1. The influence of cold work on the oxidation behaviour of stainless steel

    International Nuclear Information System (INIS)

    Langevoort, J.C.

    1985-01-01

    In this thesis the study of the interaction of oxygen gas with stainless steel surfaces is described. Thermogravimetry, microscopy and ellipsometry have been used to follow the oxidation in situ, while EDX, AES and XPS have been used to determine the oxide compositions. The aim of this thesis is to reveal the influence on the oxidation behaviour of stainless steel of i) cold work (rolling, drawing, milling, polishing and Ar ion bombardment) ii) the initially formed oxide and iii) the experimental conditions. Two types of stainless steels have been used (AISI 304 (a 18/8 Cr/Ni steel) and Incoloy 800 H (a 20/30 Cr/Ni steel)). (Auth.)

  2. Influence of Plastic Deformation on Low Temperature Surface Hardening of Austenitic and Precipitation Hardening Stainless Steels by Gaseous Nitriding

    DEFF Research Database (Denmark)

    Bottoli, Federico; Winther, Grethe; Christiansen, Thomas Lundin

    2015-01-01

    This article addresses an investigation of the influence of plastic deformation on low temperature surface hardening by gaseous nitriding of three commercial austenitic stainless steels: AISI 304, EN 1.4369 and Sandvik Nanoflex® with various degrees of austenite stability. The materials were...... case included X-ray diffraction analysis, reflected light microscopy and microhardness. The results demonstrate that a case of expanded austenite develops and that, in particular, strain-induced martensite has a large influence on the nitrided zone....

  3. High temperature corrosion studies on friction welded low alloy steel and stainless steel in air and molten salt environment at 650 oC

    International Nuclear Information System (INIS)

    Arivazhagan, N.; Narayanan, S.; Singh, Surendra; Prakash, Satya; Reddy, G.M.

    2012-01-01

    Highlights: → Thermogravimetric analysis on friction welded AISI 304 with AISI 4140 exposed in air and molten salt environment. → Comparative study on friction welded AISI 4140 with AISI 304 exposed in air, Na 2 SO 4 -60%V 2 O 5 and NaCl-50%Na 2 SO 4 at 650 o C. → SEM/EDAX, XRD analysis on corroded dissimilar AISI 304 and AISI 4140 materials. -- Abstract: The investigation on high-temperature corrosion resistance of the weldments is necessary for prolonged service lifetime of the components used in corrosive environments. This paper reports on the performance of friction welded low alloy steel AISI 4140 and stainless steel AISI 304 in air as well as molten salt environment of Na 2 SO 4 -60%V 2 O 5 and NaCl-50%Na 2 SO 4 at 650 o C. This paper reports several studies carried out for characterizing the weldments corrosion behavior. Initially thermogravimetric technique was used to establish the kinetics of corrosion. For analyzing the corrosion products, X-ray diffraction, scanning electron microscopy/energy-dispersive analysis and electron probe micro analysis techniques were used. From the results of the experiments, it is observed that the weldments suffered accelerated corrosion in NaCl-Na 2 SO 4 environment and showed spalling/sputtering of the oxide scale. Furthermore, corrosion resistance of weld interface was found to be lower than that of parent metals in molten salt environment. Weight gain kinetics in air oxidation studies reveals a steady-state parabolic rate law while the kinetics with salt deposits displays multi-stage growth rates. Moreover NaCl is the main corrosive species in high temperature corrosion, involving mixtures of NaCl and Na 2 SO 4 which is responsible for formation of internal attack.

  4. DEFORMACIÓN ELÁSTICA RESIDUAL EN LÁMINAS DE ACERO AISI 304 RECUBIERTAS CON UNA PELÍCULA DE NITRURO DE TITANIO DEPOSITADA POR PVD-MAGNETRON SPUTTERING

    Directory of Open Access Journals (Sweden)

    H. A. COLORADO

    2009-01-01

    Full Text Available Se realizó una caracterización mediante difracción de rayos x (DRX en láminas de acero inoxidable AISI 304 recubierto con una capa de nitruro de titanio de 3 um de espesor, obtenida mediante deposición física de vapor (PVD-MAGNETRON SPUTTERING a una temperatura de 200 °C. se tomaron imágenes de microscopía electrónica de barrido (MEB, microscopía óptica (MO y microscopía de fuerza atómica (MFA para caracterizar el sustrato, la capa y la zona cercana a la intercara. adicionalmente se determinó la deformación elástica residual asociada con el ensanchamiento de los picos de DRX.

  5. Strengthening of stainless steel weldment by high temperature precipitation

    OpenAIRE

    Sergio Neves Monteiro; Lucio Fabio Cassiano Nascimento; Édio Pereira Lima, Jr.; Fernanda Santos da Luz; Eduardo Sousa Lima; Fábio de Oliveira Braga

    2017-01-01

    The mechanical behavior and the strengthening mechanism of stainless steel welded joints at 600 °C have been investigated. The welds were composed of AISI 304 stainless steel, as base metal, and niobium containing AISI 347 stainless steel, as weld metal. The investigation was conducted by means of creep tests. The welded specimens were subjected to both high temperature (600 °C) and long periods (up to 2000 h) under constant load, and both mechanical properties and microstructural changes in ...

  6. Spectral analysis of the process emission during laser welding of AISI 304 stainless steel with disk and Nd:YAG laser

    NARCIS (Netherlands)

    Konuk, A.R.; Aarts, R.G.K.M.; Huis in 't Veld, A.J.

    2009-01-01

    Optical emissions from the laser welding process can be obtained relatively easy in real-time. Such emissions come from the melt pool, keyhole, or plume during welding. Therefore it is very beneficial to establish a clear relation between characteristics of these emissions and the resulting weld

  7. Tailoring plasticity of austenitic stainless steels for nuclear applications: Review of mechanisms controlling plasticity of austenitic steels below 400 °C

    Science.gov (United States)

    Meric de Bellefon, G.; van Duysen, J. C.

    2016-07-01

    AISI 304 and 316 austenitic stainless steels were invented in the early 1900s and are still trusted by materials and mechanical engineers in numerous sectors because of their good combination of strength, ductility, and corrosion resistance, and thanks to decades of experience and data. This article is part of an effort focusing on tailoring the plasticity of both types of steels to nuclear applications. It provides a synthetic and comprehensive review of the plasticity mechanisms in austenitic steels during tensile tests below 400 °C. In particular, formation of twins, extended stacking faults, and martensite, as well as irradiation effects and grain rotation are discussed in details.

  8. Analysis of the elements sputtered during the lanthanum implantation in stainless steels

    International Nuclear Information System (INIS)

    Ager, F.J.; Respaldiza, M.A.; Silva, M.F. da; Redondo, L.M.; Soares, J.C.

    1998-01-01

    The evidence of the modification of the surface structure of the AISI-304 stainless steel during the implantation of lanthanum makes the analysis of the sputtered elements very interesting. Those sputtered elements are deposited on a carbon sheet placed in front of the steel being implanted, and studied by means of RBS and PIXE, together with the implanted specimens. Besides, the protective effect of the implanted ions during the high temperature oxidation is also studied by those techniques together with XRD and thermogravimetric methods. (orig.)

  9. Effect of plastic deformation on the magnetic properties of selected austenitic stainless steels

    Directory of Open Access Journals (Sweden)

    Tatiana Oršulová

    2017-04-01

    Full Text Available Austenitic stainless steels are materials, that are widely used in various fields of industry, architecture and biomedicine. Their specific composition of alloying elements has got influence on their deformation behavior. The main goal of this study was evaluation of magnetic properties of selected steels, caused by plastic deformation. The samples were heat treated in different intervals of temperature before measuring. Then the magnetic properties were measured on device designed for measuring of magnetism. From tested specimens, only AISI 304 confirmed effect of plastic deformation on the magnetic properties. Magnetic properties changed with increasing temperature.

  10. Corrosion resistance testing of high-boron-content stainless steels

    International Nuclear Information System (INIS)

    Petrman, I.; Safek, V.

    1994-01-01

    Boron steels, i.e. stainless steels with boron contents of 0.2 to 2.25 wt.%, are employed in nuclear engineering for the manufacture of baskets or wells in which radioactive fissile materials are stored, mostly spent nuclear fuel elements. The resistance of such steels to intergranular corrosion and uniform corrosion was examined in the Strauss solution and in boric acid; the dependence of the corrosion rate of the steels on their chemical composition was investigated, and their resistance was compared with that of AISI 304 type steel. Corrosion resistance tests in actual conditions of ''wet'' compact storage (demineralized water or a weak boric acid solution) gave evidence that boron steels undergo nearly no uniform corrosion and, as electrochemical measurements indicated, match standard corrosion-resistant steels. Corrosion resistance was confirmed to decrease slightly with increasing boron content and to increase somewhat with increasing molybdenum content. (Z.S.). 3 tabs., 4 figs., 7 refs

  11. Estudio de microestructura y composición de la oxidación en vapor a 700 y 750oC de los aceros austeníticos AISI 304, 316 y 317

    Directory of Open Access Journals (Sweden)

    José Luddey Marulanda

    2013-01-01

    Full Text Available Se ha investigado la oxidación de los aceros inoxidables austeníticos AISI SAE: 304, 316 y 317; a temperaturas de 700 y 750oC, en una atmósfera próxima al 100% de vapor de agua, y de 10 a 1000h de exposición. La finalidad es comprobar la calidad de los aceros austeníticos y estudiar la morfología, composición y estructura de la fases de las capas formadas en la cascarilla del óxido de las muestras por Microscopía Electrónica de Barrido (SEM, Análisis de Rayos X por Dispersión de Energía (EDAX y Difracción de Rayos X (XRD, respectivamente. Así como también, se ha realizado a diferentes tiempos un estudio sistemático de termogravimetría de las muestras oxidadas, donde se ha observado que el acero AISI 304 presentó la menor ganancia de masa y el acero AISI 316 fue el de mayor de masa respecto a los tres aceros del trabajo. Adicionalmente fue realizado un estudio teórico de simulación termodinámica de oxidación en vapor de los tres aceros, en las mismas condiciones experimentales y mediante el programa Thermo-calc. En estos aceros oxidados se han comprobado la presencia de estructuras de fases de óxidos como: Fe2O3, espinelas protectoras Fe3O4 y Cr2NiO4, y óxidos mixtos de tipo (CrxFey2O3, (Fe,Cr,Mn3O4 y Ni6MnO8. Finalmente, se discute un posible mecanismo de la formación de las capas de óxidos de las muestras ensayadas.

  12. Etude par diffraction des rayons X in situ des mécanismes d'oxydation de l'acier AISI 304 entre 800°C et 1000°C. Influence des dépôts sol-gel de lanthane et de cérium. Apport de la spectroscopie infrarouge à l'identification des oxydes mixtes

    OpenAIRE

    Karimi , Noureddine

    2007-01-01

    This work presents a study on the AISI 304 oxidation mechanism within the temperature range of 800 to 1000°C, in air. We have closely examined the effect of Lanthanum and Cerium sol-gel coating on the oxidation process. IR spectroscopy enables us to better identify the mixed oxides FeCr2O4 and Mn1,5Cr1,5O4 and the corundum type oxides Fe2O3 and Cr2O3. The combination of various analytical techniques such as: in situ XRD, IR spectroscopy, MEB, EDS and MET, lead us to propose a new oxidation me...

  13. Low-temperature creep of austenitic stainless steels

    Science.gov (United States)

    Reed, R. P.; Walsh, R. P.

    2017-09-01

    Plastic deformation under constant load (creep) in austenitic stainless steels has been measured at temperatures ranging from 4 K to room temperature. Low-temperature creep data taken from past and unreported austenitic stainless steel studies are analyzed and reviewed. Creep at cryogenic temperatures of common austenitic steels, such as AISI 304, 310 316, and nitrogen-strengthened steels, such as 304HN and 3116LN, are included. Analyses suggests that logarithmic creep (creep strain dependent on the log of test time) best describe austenitic stainless steel behavior in the secondary creep stage and that the slope of creep strain versus log time is dependent on the applied stress/yield strength ratio. The role of cold work, strain-induced martensitic transformations, and stacking fault energy on low-temperature creep behavior is discussed. The engineering significance of creep on cryogenic structures is discussed in terms of the total creep strain under constant load over their operational lifetime at allowable stress levels.

  14. T.I.G. Welding of stainless steel. Numerical modelling for temperatures calculation in the Haz

    International Nuclear Information System (INIS)

    Martinez-Conesa, E. J.; Estrems-Amestoy, M.; Miguel-Eguia, V.; Garrido-Hernandez, A.; Guillen-Martinez, J. A.

    2010-01-01

    In this work, a numerical method for calculating the temperature field into the heat affected zone for butt welded joints is presented. The method has been developed for sheet welding and takes into account a bidimensional heat flow. It has built a computer program by MS-Excel books and Visual Basic for Applications (VBA). The model has been applied to the TIG process of AISI 304 stainless steel 2mm thickness sheet. The welding process has been considered without input materials. The numerical method may be used to help the designers to predict the temperature distribution in welded joints. (Author) 12 refs.

  15. Influence of plastic deformation on low temperature surface hardening of stainless steel by gaseous nitriding

    DEFF Research Database (Denmark)

    Bottoli, Federico; Winther, Grethe; Christiansen, Thomas Lundin

    2015-01-01

    This article addresses an investigation of the influence of plastic deformation on low temperature surface hardening by gaseous nitriding of three commercial austenitic stainless steels: AISI 304, EN 1.4369 and Sandvik Nanoflex® with various degrees of austenite stability. The materials were...... analysis, reflected light microscopy and microhardness indentation. The results demonstrate that a case of expanded austenite develops and that, in particular, the presence of strain-induced martensite in the initial (deformed) microstructure has a large influence on the nitrided zone....

  16. Laser-Beam Welding Impact on the Deformation Properties of Stainless Steels When Used for Automotive Applications

    Directory of Open Access Journals (Sweden)

    Evin Emil

    2016-09-01

    Full Text Available Materials other than standard and advanced high strength steels are remarkable for the thin-walled structures of the car-body in recent years in order to safety enhancement, weight and emission reduction, corrosion resistance improvement. Thus, there are presented in the paper the deformation properties of laser welded austenitic AISI 304 and ferritic AISI 430 stainless steels compared to these one measured for the high strength low alloyed steel H220PD. The properties were researched by tensile test and 3-point bending test with fixed ends on specimens made of basic material and laser welded one. The specimens were welded by solid state fiber laser YLS-5000 in longitudinal direction (the load direction. The deformation properties such as strength, stiffness and deformation work were evaluated and compared. The strength and stiffness were calculated from tensile test results and the deformation work was calculated from both, tensile test and 3-point bending test results. There has been found only minor effect of laser welding to the deformation properties for high strength low alloyed steel H220PD and austenitic stainless steel AISI 304. Otherwise, the laser welding strongly influenced the deformation work of the ferritic stainless steel AISI 430 as well as the elongation at tensile test.

  17. Tribological and microstructural characteristics of ion-nitrided steels

    Science.gov (United States)

    Spalvins, T.

    1983-01-01

    Three steels AISI 4140, AISI 4340 and AISI 304 stainless steel were ion nitrided in a plasma consisting of a 75:25 mixture of H2:N2, sometimes with a trace of CH4. Their surface topography was characterized by SEM and two distinct compound phases were identified: the gamma and the epsilon. The core-case hardness profiles were also established. The low Cr alloy steels have an extended diffusion zone in contrast to the 3034 stainless steels which have a sharp interface. The depth of ion-nitriding is increased as the Cr content is decreased. Friction tests reveal that the gamma surface phase has a lower coefficient of friction than the epsilon phase. The lowest coefficient of friction is achieved when both the rider and the specimen surface are ion nitrided. Previously announced in STAR as N83-24635

  18. Comparative study in the induced corrosion by sulfate reducing microorganisms, in a stainless steel 304L sensitized and a carbon steel API X65

    International Nuclear Information System (INIS)

    Diaz S, A.; Gonzalez F, E.; Arganis J, C.; Luna C, P.; Carapia M, L.

    2004-01-01

    In spite of the operational experience related with the presence of the phenomenon of microbiological corrosion (MIC) in industrial components, it was not but until the decade of the 80 s when the nuclear industry recognized its influence in some systems of Nuclear Generating Power plants. At the moment, diverse studies that have tried to explain the generation mechanism of this phenomenon exist; however, they are even important queries that to solve, especially those related with the particularities of the affected metallic substrates. Presently work, the electrochemical behavior of samples of stainless steel AISI 304L sensitized is evaluated and the carbon steel APIX65, before the action of sulfate reducing microorganisms low the same experimental conditions; found that for the APIX65 the presence of this type of bacteria promoted the formation of a stable biofilm that allowed the maintenance of the microorganisms that damaged the material in isolated places where stings were generated; while in the AISI 304L, it was not detected damage associated to the inoculated media. The techniques of Resistance to the Polarization and Tafel Extrapolation, allowed the calculation of the speed of uniform corrosion, parameter that doesn't seem to be influenced by the presence of the microorganisms; while that noise electrochemical it distinguished in real time, the effect of the sulfate reducing in the steel APIX65. (Author)

  19. Influence of Plastic Deformation on Low-Temperature Surface Hardening of Austenitic Stainless Steel by Gaseous Nitriding

    DEFF Research Database (Denmark)

    Bottoli, Federico; Winther, Grethe; Christiansen, Thomas Lundin

    2015-01-01

    This article addresses an investigation of the influence of plastic deformation on low-temperature surface hardening by gaseous nitriding of two commercial stainless steels: EN 1.4369 and AISI 304. The materials were plastically deformed to several levels of equivalent strain by conventional......, reflected-light microscopy, and microhardness testing. The results demonstrate that a case of expanded austenite develops and that the presence of plastic deformation has a significant influence on the morphology of the nitrided case. The presence of strain-induced martensite favors the formation of Cr...

  20. EBSD study of purity effects during hot working in austenitic stainless steels

    International Nuclear Information System (INIS)

    El Wahabi, M.; Gavard, L.; Cabrera, J.M.; Prado, J.M.; Montheillet, F.

    2005-01-01

    The technique of electron back scattering diffraction (EBSD) is considered as a powerful instrument for the study of the microstructural changes during hot forming processes and gives the possibility to present the information in different ways (OIM, misorientation diagram and pole figures). The present work is focused on the observation by EBSD of the microstructure evolution during deformation at high temperature of three austenitic stainless steels: AISI-304H, AISI-304L and a high purity steel HP. The difference between the three steels is the content carbon and the presence of residual elements. To this aim compression tests were carried out at a constant strain rate of 0.001 s -1 and different temperatures. The study showed an increase of twin boundary fractions and a diminution of substructure (low angle densities boundaries) at increasing temperatures. On the other hand, increasing carbon content promotes lower twin boundary fractions and larger amounts of low angle boundaries. This effect can be explained by the reduction of grain boundary mobility caused by increasing carbon contents, which in turn reduces the migration rate and consequently the probability of twin boundary generation. Moreover, the increment of low angle boundaries with carbon content accelerates the twin character loss. It was also found that the dynamically recrystallized grain size decreased at increasing carbon content due to a typical drag effect. No important features on textures were found during DDRX

  1. Tailoring plasticity of austenitic stainless steels for nuclear applications: Review of mechanisms controlling plasticity of austenitic steels below 400 °C

    Energy Technology Data Exchange (ETDEWEB)

    Meric de Bellefon, G., E-mail: mericdebelle@wisc.edu [University of Wisconsin-Madison (United States); Duysen, J.C. van [EDF R& D (France); University of Tennessee-Knoxville (United States); Unité Matériaux et Transformation (UMET) CNRS, Université de Lille (France)

    2016-07-15

    AISI 304 and 316 austenitic stainless steels were invented in the early 1900s and are still trusted by materials and mechanical engineers in numerous sectors because of their good combination of strength, ductility, and corrosion resistance, and thanks to decades of experience and data. This article is part of an effort focusing on tailoring the plasticity of both types of steels to nuclear applications. It provides a synthetic and comprehensive review of the plasticity mechanisms in austenitic steels during tensile tests below 400 °C. In particular, formation of twins, extended stacking faults, and martensite, as well as irradiation effects and grain rotation are discussed in details. - Highlights: • This article is part of an effort to tailor the plasticity of 304L and 316L steels for nuclear applications. • It reviews mechanisms controlling plasticity of austenitic steels during tensile tests. • Formation of twins, extended stacking faults, and martensite, grain rotation, and irradiation effects are discussed.

  2. Some mechanical properties of borided AISI H13 and 304 steels

    International Nuclear Information System (INIS)

    Taktak, Sukru

    2007-01-01

    In the present study, mechanical properties of borides formed on AISI H13 hot work tool and AISI 304 stainless steels have been investigated. Both steels have high chromium content and have a widespread use in the engineering application. Boriding treatment was carried out in slurry salt bath consisting of borax, boric acid, and ferrosilicon at temperature range of 800-950 deg. C for 3, 5, and 7 h. X-ray diffraction analysis of boride layers on the surface of steels revealed various peaks of FeB, Fe 2 B, CrB, and Ni 3 B. Metallographic studies showed that the boride layer has a flat and smooth morphology in the 304 steel while H13 steel was a ragged morphology. The characterization of the boride layer is also carried out by means of the micro-hardness, surface roughness, adhesion, and fracture toughness studies

  3. Adherence and electrochemical behavior of calcium titanate coatings onto 304 stainless steel substrate

    Energy Technology Data Exchange (ETDEWEB)

    Esguerra A, J.; Aguilar, Y. [Universidad del Valle, Escuela de Ingenieria de Materiales, TPMR, Calle 13 No. 100-00, A. A. 25360 Cali (Colombia); Aperador, W. [Escuela Colombiana de Ingenieria Julio Garavito, Escuela de Ingenieria Mecanica, AK 45 No. 205-59 (Autopista Norte), A. A. 14520 Bogota (Colombia); Alba de Sanchez, N. [Universidad Autonoma de Occidente, Grupo de Investigacion en Ciencia e Ingenieria de Materiales, Calle 25 No. 115-85, A. A. 2790 Cali (Colombia); Bolanos P, G.; Rincon, C., E-mail: johanna.esguerra@univalle.edu.co [Universidad del Cauca, Departamento de Fisica, Laboratorio de Fisica de Bajas Temperaturas, Calle 5 No. 4-70, A. A. 996 Popayan (Colombia)

    2014-07-01

    Calcium titanate has been proposed as a coating for biomedical applications but it has not been reported characterization of adhesion failure mechanisms or electrochemical properties in time. In this work have been studied these properties of a calcium titanate coating growth onto AISI 304 steel deposited by r.f. magnetron sputtering. It was found that the coating has a critical adhesive load of 6.53 ± 0.14 N. With respect to its electrochemical properties potentiodynamic polarization curves show that the calcium titanate coating provides protection to AISI 304 steel. However. EIS indicates that even though metal dissolution occur through the pores in the coating, this leads to the precipitation of salts that block pores; this precipitates layer acts like and additional barrier to the metal dissolution in the system. The coatings deposition was carried out via magnetron sputtering during 4 hours at 500 grades C. The crystal structure of the films was determined by using glancing incident X-ray diffraction. The chemical composition of deposited films was performed by impedance dispersive X-ray spectroscopy (EDX) in the scanning electron microscopy (Jeol JSM-649 OLV Sem), and the grain size and the roughness was obtained using an atomic force microscopy from Asylum Research MFP-3D using a cantilever silicon tip in non-contact mode and calculated by scanning probe image processor. (Author)

  4. Characterization of the dissimilar welding - austenitic stainless steel with filler metal of the nickel alloy

    International Nuclear Information System (INIS)

    Soares, Bruno Amorim; Schvartzman, Monica Maria de Abreu Mendonca; Campos, Wagner Reis da Costa

    2007-01-01

    In elevated temperature environments, austenitic stainless steel and nickel alloy has a superior corrosion resistance due to its high Cr content. Consequently, this alloys is widely used in nuclear reactors components and others plants of energy generation that burn fossil fuel or gas, chemical and petrochemical industries. The object of the present work was to research the welding of AISI 304 austenitic stainless steel using the nickel alloy filler metals, Inconel 625. Gas tungsten arc welding, mechanical and metallographic tests, and compositional analysis of the joint were used. A fundamental investigation was undertaken to characterize fusion boundary microstructure and to better understand the nature and character of boundaries that are associated with cracking in dissimilar welds. The results indicate that the microstructure of the fusion zone has a dendritic structure, inclusions, and precipitated phases containing Ti and Nb are present in the inter-dendritic region. In some parts near to the fusion line it can be seen a band in the weld, probably a eutectic phase with lower melting point than the AISI 304, were the cracking may be beginning by stress corrosion. (author)

  5. Adherence and electrochemical behavior of calcium titanate coatings onto 304 stainless steel substrate

    International Nuclear Information System (INIS)

    Esguerra A, J.; Aguilar, Y.; Aperador, W.; Alba de Sanchez, N.; Bolanos P, G.; Rincon, C.

    2014-01-01

    Calcium titanate has been proposed as a coating for biomedical applications but it has not been reported characterization of adhesion failure mechanisms or electrochemical properties in time. In this work have been studied these properties of a calcium titanate coating growth onto AISI 304 steel deposited by r.f. magnetron sputtering. It was found that the coating has a critical adhesive load of 6.53 ± 0.14 N. With respect to its electrochemical properties potentiodynamic polarization curves show that the calcium titanate coating provides protection to AISI 304 steel. However. EIS indicates that even though metal dissolution occur through the pores in the coating, this leads to the precipitation of salts that block pores; this precipitates layer acts like and additional barrier to the metal dissolution in the system. The coatings deposition was carried out via magnetron sputtering during 4 hours at 500 grades C. The crystal structure of the films was determined by using glancing incident X-ray diffraction. The chemical composition of deposited films was performed by impedance dispersive X-ray spectroscopy (EDX) in the scanning electron microscopy (Jeol JSM-649 OLV Sem), and the grain size and the roughness was obtained using an atomic force microscopy from Asylum Research MFP-3D using a cantilever silicon tip in non-contact mode and calculated by scanning probe image processor. (Author)

  6. Corrosion behavior of powder metallurgical stainless steels in urban and marine environments

    Directory of Open Access Journals (Sweden)

    Bautista, A.

    2006-06-01

    Full Text Available This work studies the development of corrosive attack on sintered components manufactured from AISI 316L and AISI 304L powders. The stainless steels were sintered in vacuum and in nitrogen-base atmosphere at 1,120 and 1,250 ºC, and their corrosion resistance was then analyzed by electrochemical techniques and by atmospheric corrosion testing (two years at urban and marine test sites. Images are shown of the morphology of the attack on the surface of the stainless steels and the development of this attack in the interior of the material.

    Este trabajo estudia el desarrollo del proceso corrosivo en componentes sinterizados fabricados a partir de polvos de AISI 316L y AISI 304L. Los aceros inoxidables fueron sinterizados en vacío y en atmósfera base nitrógeno a 1.120 y 1.250 ºC y, su resistencia a corrosión se ha analizado mediante técnicas electroquímicas y mediante ensayos de corrosión atmosférica (dos años en ambientes urbano y marino. Se muestran imágenes de la morfología del ataque en la superficie de los aceros inoxidables y del desarrollo de este ataque en el interior del material.

  7. Microestrutura de uma Solda Dissimilar entre o Aço Inoxidável Ferrítico AISI 410S e o Aço Inoxidável Austenítico AISI 304L Soldado pelo Processo FSW

    Directory of Open Access Journals (Sweden)

    Tathiane Caminha Andrade

    2015-12-01

    Full Text Available Resumo O presente trabalho visa investigar a microestrutura formada na soldagem dissimilar entre chapas de aços inoxidáveis ferríticos AISI 410S e aços inoxidáveis austeníticos AISI 304L pelo processo friction stir welding. A soldagem foi realizada com o ajuste dos seguintes parâmetros: rotação 450 rpm; velocidade de soldagem de 1,0 mm/s; e força axial 40 kN. O aço AISI 410S foi posicionado no lado de avanço enquanto que o aço AISI 304L foi posicionado no lado de retrocesso. A análise consistiu de preparação metalográfica e caracterização microestrutural por microscopia ótica e microscopia eletrônica de varredura. Para o aço AISI 410S foi observada a formação de martensita associada com ferrita na zona de mistura (ZM, zona termomecanicamente afetada (ZTMA e na zona afetada pelo calor (ZAC. As características do processo de soldagem FSW resultaram num refino de grão para o aço inoxidável ferrítico, posicionado no lado de avanço, tanto na ZM quanto nas ZTMA e ZAC. O mesmo comportamento não foi observado para o lado austenítico.

  8. Hydrogenation of stainless steels implanted with nitrogen

    International Nuclear Information System (INIS)

    Silva Ramos, L.E. da.

    1989-01-01

    In the present work the effects of both ion implantation and hydrogenation on the fatigue behaviour of an AISI-304 type unstable stainless steel was studied. The material was tested under the following microstructural conditions: annealed; annealed plus hydrogenated; annealed plus ion-implanted; annealed, ion-implanted and hydrogeneted. The hydrogen induced phase transformations were also studied during the outgassing of the samples. The ion implanted was observed to retard the kinetics of the hydrogen induced phase transformations. It was also observed that the nitrogen ion implantation followed by both natural (for about 4 months) and artificial (100 0 C for 6 hours) aging treatments was beneficial to the fatigue life of both non hydrogenated and severely hydrogenated samples. (author) [pt

  9. Effects of sulphur ion implantation on the electrochemical behaviour of two stainless steels in sulphuric medium

    International Nuclear Information System (INIS)

    Nader-Roux, J.; Becdelievre, A.M. de; Gaillard, F.; Roux, R.; Becdelievre, J. de

    1986-01-01

    The electrochemical behaviour in sulphuric acid of two austenitic stainless steels (AISI 304 L and AISI 321) modified by sulphur ion implantation has been studied. Surface analysis of oxygen and sulphur by LEEIXS and XRFS were performed before and after polarization on unimplanted and on implanted samples. I/E curves with implanted steels reveal an important corrosion peak (α peak) recovering widely the active peak of unimplanted samples. For high implanted doses, another peak (β peak) appears in the passive range. High doses implanted steels polarized in the range of the α peak exhibit a sulphur enriched black surface layer. SEM examination of this layer shows it is constituted by flakes rolling up themselves. The formation of a superficial non-protective sulphide layer and the internal stresses of this layer explain the corrosion enhancement of sulphur implanted materials. After dissolution of this layer the behaviour of unimplanted steels is found again. (author)

  10. Stainless steels in boiling water reactors. Corrosion problems and possible solutions

    International Nuclear Information System (INIS)

    Combrade, P.; Desestret, A.; Leroy, F.; Coriou, H.

    1977-01-01

    In boiling water reactors, the heat-carrying water may have an up to 0.1 or even 0.2 ppm oxygen content, which can make it highly agressive at operating temperature for stainless steels subject to high physical stresses. Several metallurgical solutions can be considered, and in particular the use of stainless steels having a mixed austenitic-ferritic structure or of standard austenitic steels (18.10 or 18.10 Mo, such as AISI 304 and 316) with carefully controlled carbon and alloy element contents. The behavior of these steels during prolonged tests in water at 288 0 C with a 30 and even 100 ppm oxygen content turned out to be quite satisfactory [fr

  11. Phase transformation by fatigue in austenitic stainless steel

    International Nuclear Information System (INIS)

    Jo, Y.S.; Kwun, S.I.

    1988-01-01

    The effect of strain induced martensite on the fatigue behavior of AISI 304 austenitic stainless steel was investigated. During low cycle fatigue, the austenitic stainless steel showed a continuous cyclic hardening until fracture. The extent of cyclic hardening increased with decreasing austenite stability. The austenite stability was controlled by different aging time and temperature, which resulted in different carbide morphologies. The fatigue crack propagation rate near ΔK th varied also with the austenite stability inside the plastic zone at the crack up. Especially, the near-threshold fatigue crack propagation rate of the grain boundary carbide precipitated condition was the lowest. This was considered to be due to the roughness induced closure caused by intergranular facet. A new model for the intergranular facet formation and the fatigue crack propagation of grain boundary carbide precipitated condition was proposed. (Author)

  12. Tribological effects of oxygen ion implantation into stainless steel

    International Nuclear Information System (INIS)

    Evans, P.J.; Vilaithong, T.; Yu, L.D.; Monteiro, O.R.; Yu, K.M.; Brown, I.G.

    2000-01-01

    The formation of sub-surface oxide layers by hybrid metal-gas co-implantation into steel and other metals can improve their tribological properties. In this report, we compare the wear and friction performance of previously studied Al + O hybrid implants with that produced by single species oxygen ion (O + ) implantation under similar conditions. The substrates were AISI 304L stainless steel discs polished to a final mirror finish using 1 μm diamond paste, and the ion implantation was done using a conventional swept-beam technique at ion energies of 70 or 140 keV and doses of up to 1x10 17 cm -2 . The wear and friction behaviour of the implanted and unimplanted material was measured with a pin-on-disc tribometer. Here we describe the experimental procedure and results, and discuss the improvement relative to that achieved with surface layers modified by metal-gas co-implantation

  13. PITTING CORROSION OF STAINLESS STEEL AT THE VARIOUS SURFACE TREATMENT

    Directory of Open Access Journals (Sweden)

    Viera Zatkalíková

    2011-09-01

    Full Text Available The stainless steel surface treatment is very important with regard to its pitting corrosion susceptibility. An effect of various types surfacing on pitting corrosion resistance of AISI 304stainless steel is investigated in this work. The samples of the tested material are turned, blasted, peened, grinded and a half of them are pickled to achieve higher purity of surfaces and better quality of passive film. Eight types of different finished surfaces are tested by electrochemical and immersion tests to determine corrosion behaviour in conditions where pitting is evoked by controlled potential and second by solution with high redox potential. By this way the effect of mechanical and chemical surface treatment on the resistance to pitting corrosion, character, size and shape of pits are compared in the conditions of different mechanisms of corrosion process.

  14. T.I.G. Welding of stainless steel. Numerical modelling for temperatures calculation in the Haz; Soldadura T.I.G. de acero inoxidable. Modelo numerico para el calculo de temperaturas en la ZAT

    Energy Technology Data Exchange (ETDEWEB)

    Martinez-Conesa, E. J.; Estrems-Amestoy, M.; Miguel-Eguia, V.; Garrido-Hernandez, A.; Guillen-Martinez, J. A.

    2010-07-01

    In this work, a numerical method for calculating the temperature field into the heat affected zone for butt welded joints is presented. The method has been developed for sheet welding and takes into account a bidimensional heat flow. It has built a computer program by MS-Excel books and Visual Basic for Applications (VBA). The model has been applied to the TIG process of AISI 304 stainless steel 2mm thickness sheet. The welding process has been considered without input materials. The numerical method may be used to help the designers to predict the temperature distribution in welded joints. (Author) 12 refs.

  15. Effect of Brass Interlayer Sheet on Microstructure and Joint Performance of Ultrasonic Spot-Welded Copper-Steel Joints

    Science.gov (United States)

    Satpathy, Mantra Prasad; Kumar, Abhishek; Sahoo, Susanta Kumar

    2017-07-01

    Solid-state ultrasonic spot welding (USW) inevitably offers a potential solution for joining dissimilar metal combination like copper (Cu) and steel (SS). In this study, the USW has been performed on Cu (UNS C10100) and SS (AISI 304) with brass interlayer by varying various welding parameters, aiming to identify the interfacial reaction, changes in microstructure and weld strength. The highest tensile shear and T-peel failure loads of 1277 and 174 N are achieved at the optimum conditions like 68 µm of vibration amplitude, 0.42 MPa of weld pressure and 1 s of weld time. The fractured surface analysis of brass interlayer and AISI 304 stainless steel samples reveals the features like swirls, voids and intermetallic compounds (IMCs). These IMCs are composed of CuZn and FeZn composite-like structures with 1.0 μm thickness. This confirms that the weld quality is specifically sensitive to the levels of input parameter combinations as well as the type of material present on the sonotrode side.

  16. Design of welding parameters for laser welding of thin-walled stainless steel tubes using numerical simulation

    Science.gov (United States)

    Nagy, M.; Behúlová, M.

    2017-11-01

    Nowadays, the laser technology is used in a wide spectrum of applications, especially in engineering, electronics, medicine, automotive, aeronautic or military industries. In the field of mechanical engineering, the laser technology reaches the biggest increase in the automotive industry, mainly due to the introduction of automation utilizing 5-axial movements. Modelling and numerical simulation of laser welding processes has been exploited with many advantages for the investigation of physical principles and complex phenomena connected with this joining technology. The paper is focused on the application of numerical simulation to the design of welding parameters for the circumferential laser welding of thin-walled exhaust pipes from theAISI 304 steel for automotive industry. Using the developed and experimentally verified simulation model for laser welding of tubes, the influence of welding parameters including the laser velocity from 30 mm.s-1 to 60 mm.s-1 and the laser power from 500 W to 1200 W on the temperature fields and dimensions of fusion zone was investigated using the program code ANSYS. Based on obtained results, the welding schedule for the laser beam welding of thin-walled tubes from the AISI 304 steel was suggested.

  17. Comparative study in the induced corrosion by sulfate reducing microorganisms, in a stainless steel 304L sensitized and a carbon steel API X65; Estudio comparativo de la corrosion inducida por microorganismos sulfatorreductores, en un acero inoxidable 304L sensibilizado y un acero al carbono API X65

    Energy Technology Data Exchange (ETDEWEB)

    Diaz S, A.; Gonzalez F, E.; Arganis J, C.; Luna C, P.; Carapia M, L. [ININ, Carretera Mexico-Toluca Km. 36.5, 52045 Estado de Mexico (Mexico)]. e-mail: ads@nuclear.inin.mx

    2004-07-01

    In spite of the operational experience related with the presence of the phenomenon of microbiological corrosion (MIC) in industrial components, it was not but until the decade of the 80 s when the nuclear industry recognized its influence in some systems of Nuclear Generating Power plants. At the moment, diverse studies that have tried to explain the generation mechanism of this phenomenon exist; however, they are even important queries that to solve, especially those related with the particularities of the affected metallic substrates. Presently work, the electrochemical behavior of samples of stainless steel AISI 304L sensitized is evaluated and the carbon steel APIX65, before the action of sulfate reducing microorganisms low the same experimental conditions; found that for the APIX65 the presence of this type of bacteria promoted the formation of a stable biofilm that allowed the maintenance of the microorganisms that damaged the material in isolated places where stings were generated; while in the AISI 304L, it was not detected damage associated to the inoculated media. The techniques of Resistance to the Polarization and Tafel Extrapolation, allowed the calculation of the speed of uniform corrosion, parameter that doesn't seem to be influenced by the presence of the microorganisms; while that noise electrochemical it distinguished in real time, the effect of the sulfate reducing in the steel APIX65. (Author)

  18. The specific heat loss combined with the thermoelastic effect for an experimental analysis of the mean stress influence on axial fatigue of stainless steel plain specimens

    Directory of Open Access Journals (Sweden)

    G. Meneghetti

    2014-10-01

    Full Text Available The energy dissipated to the surroundings as heat in a unit volume of material per cycle, Q, was recently proposed by the authors as fatigue damage index and it was successfully applied to correlate fatigue data obtained by carrying out fully reversed stress- and strain-controlled fatigue tests on AISI 304L stainless steel plain and notched specimens. The use of the Q parameter to analyse the experimental results led to the definition of a scatter band having constant slope from the low- to the high-cycle fatigue regime. In this paper the energy approach is extended to analyse the influence of mean stress on the axial fatigue behaviour of unnotched cold drawn AISI 304L stainless steel bars. In view of this, stress controlled fatigue tests on plain specimens at different load ratios R (R=-1; R=0.1; R=0.5 were carried out. A new energy parameter is defined to account for the mean stress effect, which combines the specific heat loss Q and the relative temperature variation due to the thermoelastic effect corresponding to the achievement of the maximum stress level of the stress cycle. The new two-parameter approach was able to rationalise the mean stress effect observed experimentally. It is worth noting that the results found in the present contribution are meant to be specific for the material and testing condition investigated here.

  19. Study of dislocation mobility in 304 stainless steel

    International Nuclear Information System (INIS)

    Lima, L.F.C.P.; Miranda, P.E.V.; Monteiro, S.N.

    1991-01-01

    Internal friction, IF, measurements were carried out in a type AISI 304 austenitic stainless steel, SS, at approximately 1 Hz of frequency in the temperature interval from 120 to 573K. The IF and the frequency spectra were obtained in samples which had gone through specific heat treatment. The results showed IF spectra with a well defined peak at 260K. The intensity of this peak depends on the amount of plastic deformation previously introduced in the sample. Another bread peak was detected between 300 and 400K. Both peaks could only be detected after plastic deformation whether torsion or uniaxial tension. In torsionally deformed samples at 77K the IF spectrum snows a high damping due to a possible phase transformation which occurs around room temperature, RT. The broad peak at higher temperature is sensitive to recovery induced by linear annealings. (author)

  20. Temperature dependent measurement of internal damping of austenitic stainless steels

    Directory of Open Access Journals (Sweden)

    Oravcová Monika

    2018-01-01

    Full Text Available This article is aimed on the analysis of the internal damping changes of austenitic stainless steels AISI 304, AISI 316L and AISI 316Ti depending from temperature. In experimental measurements only resonance method was used which is based on continuous excitation of oscillations of the specimens and the whole apparatus vibrates at the frequency near to the resonance. Microplastic processes and dissipation of energy within the metals are evaluated and investigated by internal damping measurements. Damping capacity of materials is closely tied to the presence of defects including second phase particles and voids. By measuring the energy dissipation in the material, we can determine the elastic characteristics, Youngs modulus, the level of stress relaxation and many other.

  1. EPR method for the detection of sensitization in stainless steels

    International Nuclear Information System (INIS)

    Clarke, W.L.; Cowan, R.L.

    1980-01-01

    The overall objective of the program was to improve the reliability of reactor system piping by increasing knowledge of failure causing mechanisms and by enhancing the capability for design evaluation and analysis. Toward the attainment of that objective, a technique has been developed to measure the degree of sensitization quantitatively in thermally treated AISI-304, -304L, -316 and 316L stainless steels. The Electrochemical Potentiokinetic Reactivation (EPR) test was developed because of an industrial need for a rapid, nondestructive, quantitative field test which could be used for assessing sensitization in reactor components. The EPR method consists of developing potentiokinetic curves on a polarized sample obtained by controlled potential sweep from the passive to the active region (reactivation) in a specific electrolyte; details of the test technique have been reported

  2. Ion-nitriding of austenitic stainless steels

    International Nuclear Information System (INIS)

    Pacheco, O.; Hertz, D.; Lebrun, J.P.; Michel, H.

    1995-01-01

    Although ion-nitriding is an extensively industrialized process enabling steel surfaces to be hardened by nitrogen diffusion, with a resulting increase in wear, seizure and fatigue resistance, its direct application to stainless steels, while enhancing their mechanical properties, also causes a marked degradation in their oxidation resistance. However, by adaption of the nitriding process, it is possible to maintain the improved wear resistant properties while retaining the oxidation resistance of the stainless steel. The controlled diffusion permits the growth of a nitrogen supersaturated austenite layer on parts made of stainless steel (AISI 304L and 316L) without chromium nitride precipitation. The diffusion layer remains stable during post heat treatments up to 650 F for 5,000 hrs and maintains a hardness of 900 HV. A very low and stable friction coefficient is achieved which provides good wear resistance against stainless steels under diverse conditions. Electrochemical and chemical tests in various media confirm the preservation of the stainless steel characteristics. An example of the application of this process is the treatment of Reactor Control Rod Cluster Assemblies (RCCAs) for Pressurized Water Nuclear Reactors

  3. Low-Temperature Nitriding of Deformed Austenitic Stainless Steels with Various Nitrogen Contents Obtained by Prior High-Temperature Solution Nitriding

    DEFF Research Database (Denmark)

    Bottoli, Federico; Winther, Grethe; Christiansen, Thomas Lundin

    2016-01-01

    In the past decades, high nitrogen steels (HNS) have been regarded as substitutes for conventional austenitic stainless steels because of their superior mechanical and corrosion properties. However, the main limitation to their wider application is their expensive production process....... As an alternative, high-temperature solution nitriding has been applied to produce HNS from three commercially available stainless steel grades (AISI 304L, AISI 316, and EN 1.4369). The nitrogen content in each steel alloy is varied and its influence on the mechanical properties and the stability of the austenite...... investigated. Both hardness and yield stress increase and the alloys remain ductile. In addition, strain-induced transformation of austenite to martensite is suppressed, which is beneficial for subsequent low-temperature nitriding of the surface of deformed alloys. The combination of high- and low...

  4. Investigation of attenuation coefficients of some stainless steel and aluminum alloys

    Science.gov (United States)

    Caner, Zafer; Tufan, Mustafa ćaǧatay

    2018-02-01

    In this study, attenuation coefficients of two different stainless steel alloys (AISI 304 and AISI 310), which have a wide range of applications from home appliances to the automotive sector, and two different aluminum alloys (6013 and 5083), which have a high mechanical strength and a light weight structure and are used in many fields from aviation to military vehicles, has been determined. For this purpose, we used gamma spectrometer system with NaI(Tl) detector. In our measurements, we used Eu-152, Ra-226 and Co-60 as gamma ray sources. To narrow the beam of gamma rays, we designed the new steel based collimator. We also investigated the effect of using collimator. Obtained results were compared with the NIST XCOM values.

  5. Open Circuit Potential Study of Stainless Steel in Environment Containing Marine Sulphate-Reducing Bacteria

    International Nuclear Information System (INIS)

    Fathul Karim Sahrani; Madzlan Abd. Aziz; Zaharah Ibrahim; Adibah Yahya

    2008-01-01

    The corrosion potential of AISI 304 stainless steel coupons influenced by sulphate-reducing bacteria (SRB) has been studied. Pure colony of SRB was isolated from the Malaysia Marine and Heavy Engineering, Pasir Gudang, Johor. Open circuit potential measurements were carried out in variable types of culturing solutions with SRB1, SRB2, combination of SRB1 and SRB2 and without SRBs inoculated. Results showed that the corrosion potential, E oc increased in the presence of SRBs (in pure and mixed culture) compared to that of control. EDS analysis showed the strong peak of sulphur in coupon containing SRB cultures compared to the control. ESEM data showed that the high density cell of SRBs were associated with corroding sections of surface steel comparing with non-corroding sections for coupons immersed in VMNI medium containing SRBs. (author)

  6. Modulation of dry tribological property of stainless steel by femtosecond laser surface texturing

    Science.gov (United States)

    Wang, Zhuo; Zhao, Quanzhong; Wang, Chengwei; Zhang, Yang

    2015-06-01

    We reported on the modification of tribological properties of stainless steel by femtosecond laser surface microstructuring. Regular arranged micro-grooved textures with different spacing were produced on the AISI 304L steel surfaces by an 800-nm femtosecond laser. The tribological properties of smooth surface and textured surface were investigated by carrying out reciprocating ball-on-flat tests against Al2O3 ceramic balls under dry friction. Results show that the spacing of micro-grooves had a significant impact on friction coefficient of textured surfaces. Furthermore, the wear behaviors of smooth and textured surface were also investigated. Femtosecond laser surface texturing had a marked potential for modulating friction and wear properties if the micro-grooves were distributed in an appropriate manner.

  7. Microstructural evolution and strain hardening behavior of the cold-drawn austenitic stainless steels

    International Nuclear Information System (INIS)

    Choi, Jeom Yong; Jin, Won

    1998-01-01

    The strain induced α ' -martensite formation and the strain hardening behavior of metastable austenitic stainless steel during cold drawing have been investigated. The strain induced α ' -martensite nucleates mainly at the intersection of the mechanical twins rather than ε-martensite. It could be explained by the increase of stacking fault energy which arises from the heat generated during high speed drawing and, for AISI 304/Cu, the additional effect of Cu additions. The strain hardening behavior of austenitic stainless steel is strongly related to the microstructural evolution accompanied by strain induced α ' -martensite. The work hardening rates of cold-drawn 304 increased with increasing interstitial element(C,N) contents which affect the strength of the strain induced α ' -martensite

  8. Electrochemical behaviour of a stainless steel coating after thermal fatigue and thermal shocks

    International Nuclear Information System (INIS)

    Boudebane, A.; Darsouni, A.; Chadli, H.; Boudebane, S.

    2012-01-01

    This work aims to study of the influence of thermal fatigue and thermal shock on the corrosion behaviour of coated steel AISI 304L. The coating was welded by TIG welding on specimens in ferritic-pearlitic steel grade AISI 4140. The study concerns three different states of deposit: sensitized, sensitized and strain hardened in surface and no sensitized. We realized electrochemical corrosion in an aqueous solution of NaCl 34 g/l. The corrosion of the specimens were evaluated by comparing the potentiodynamic curves for different states of the coating. Firstly, electrochemical characterization of deposits has shown a localized intergranular corrosion. Furthermore, the increase in the number of cycles of thermal fatigue accelerates the dissolution of deposit. Thermal shocks tend to improve resistance to corrosion. Against, the mechanical treatment of surfaces by burnishing decreases the dissolution rate of deposit cycles in thermal fatigue. (authors)

  9. Anti-biofouling superhydrophobic surface fabricated by picosecond laser texturing of stainless steel

    Science.gov (United States)

    Sun, Ke; Yang, Huan; Xue, Wei; He, An; Zhu, Dehua; Liu, Wenwen; Adeyemi, Kenneth; Cao, Yu

    2018-04-01

    Anti-biofouling technology is based on specifically designed materials and coatings. This is an enduring goal in the maritime industries, such as shipping, offshore oil exploration, and aquaculture. Recently, research of the relationship between wettability and antifouling effectiveness has attracted considerable attention, due to the anti-biofouling properties of the lotus leaf and shark skin. In this study, super-hydrophobic surfaces (SHSs) with controllable periodic structures were fabricated on AISI304 stainless steel by a picosecond laser, and their anti-biofouling performance were investigated by seawater immersion for five weeks in summertime. The results showed that the specimens with SHS demonstrate significant anti-biofouling effect as compared with the bare stainless steel plate. We observed that nearly 50% decrease of the average microbe attachment area ratio (Avg. MAAR) could be obtained. The micro-groove SHS with more abundant hierarchical micro-nano structures showed better anti-biofouling performance than the micro-pit SHS.

  10. Effect of HNO3-cerium(IV) decontamination on stainless steel canister materials

    International Nuclear Information System (INIS)

    Westerman, R.E.; Mackey, D.B.

    1991-01-01

    Stainless steel canisters will be filled with vitrified radioactive waste at the West Valley Demonstration Project (WVDP), West Valley, NY. After they are filled, the sealed canisters will be decontaminated by immersion in a HNO 3 -Ce(IV) solution, which will remove the oxide film and a small amount of metal from the surface of the canisters. Studies were undertaken in support of waste form qualification activities to determine the effect of this decontamination treatment on the legibility of the weld-bead canister identification label, and to determine whether this decontamination treatment could induce stress-corrosion cracking (SCC) in the AISI 304L stainless steel (SS) canister material. Neither the label legibility nor the canister integrity with regard to SCC were found to be prejudiced by the simulated decontamination treatment

  11. Martingalas discretas. Aplicaciones

    Directory of Open Access Journals (Sweden)

    Miguel A. Marmolejo

    2009-12-01

    Full Text Available Debido a su amplio rango de aplicaciones, la teoría de las martingalas es parte fundamental de la probabilidad. En este artículo se presentan las nociones básicas de las martingalas discretas y se recopilan algunas de sus aplicaciones en probabilidad y análisis, dando idea de los diferentes contextos donde se usan.

  12. AISI 304 ÖSTENİTİK PASLANMAZ ÇELİKLERİN TİTANYUM KARBÜR KAPLAMALI KESİCİ TAKIM İLE TORNALAMA İŞLEMİNDE KESME KUVVETLERİNİN İNCELENMESİ

    Directory of Open Access Journals (Sweden)

    Özgür TEKASLAN

    2007-02-01

    Full Text Available Bu araştırmada, AISI 304 östenitik paslanmaz çeliklerin titaniyum karbür kaplı kesici takımlarla tornalama işleminde oluşan kesme kuvvetleri deneysel olarak incelenmiş ve elde edilen sonuçlar teorik sonuçlarla karşılaştırılmıştır. Deneysel çalışmada, farklı kesme hızları, ilerleme değerleri ve kesme derinlikleri dikkate alınmıştır. Kesme kuvvetleri üç boyutlu kistler dinanometre ile ölçülmüştür. Teorik çalışmada ise; Kienzle formülasyonuna göre kesme kuvvetleri belirlenmiştir. Çalışma sonucunda teorik olarak hesaplanan kesme kuvvetlerinin çeşitli etkenler nedeni ile tam sonucu vermediği, deneysel sonuçlara göre; ortalama % 25'lik fark olduğu tespit edilmiştir. Bu nedenle kesme kuvvetlerinin belirlenmesinde deneysel yöntemin daha kesin sonuçlar verdiği değerlendirilmektedir.

  13. Stress corrosion cracking of austenitic stainless steel in glycerol solution and chloride solution at elevated temperature

    International Nuclear Information System (INIS)

    Haftirman; Maruhum Tua Lubis

    2009-01-01

    Stress Corrosion Cracking (SCC) is an environmentally assisted failure caused by exposure to a corrodant while under a sustained tensile stress. SCC is most often rapid, unpredictable and catastrophic. Failure can occur in as little as a few hours or take years to happen. Most alloys are susceptible to SCC in one or more environments requiring careful consideration of alloy type in component design. In aqueous chloride environments austenitic stainless steels and many nickel based alloys are known to perform poorly. One of products Oleo chemical is glycerol solution. Glycerol solution contains chloride with concentration 50 ppm - 150 ppm. Austenitic stainless steel is usually used in distillation construction tank and pipe line of glycerol. Material AISI 304 will be failure in this glycerol solution with this concentration in 5 years. In production process, concentration of chloride in glycerol becomes more than 150 ppm at temperature 150 degree Celsius. The reason is that the experiment I conducted in high chloride with concentration such as 6000 ppm, 9000 ppm, and 12000 ppm. The stress corrosion cracking of the austenitic stainless steels of types AISI 304, 316 and 316L in glycerol solution at elevated temperature 150 degree Celsius is investigated as a function variation of chloride concentration, namely 50, 6000, 9000 and 12000 ppm using a constant load method with two kinds of initial tensile stress as 50 % and 70 % yield strength. The experiment uses a spring loaded fixture type and is based on ASTM G49 for experiment method, and E292 for geometry of specimen. Pitting corrosion occurs on the surface specimen until the stress level reaches the ultimate strength. Pitting corrosion attack and depletion occur on the surface as initiation of SCC failure as the stress reaches the ultimate strength. Failure has occurred in catastrophic brittle fracture type of transgranular. AISI 304 was more susceptible for all conditions. In chloride solution with concentration of

  14. Ductility in a new low nickel stainless steel for reinforced concrete

    Directory of Open Access Journals (Sweden)

    Cobo, A.

    2011-12-01

    Full Text Available This paper discusses the stress-strain curves for a new low nickel stainless steel, a conventional AISI 304 stainless steel and a carbon steel commonly used in reinforced concrete structures. Ductility was studied in terms of ultimate tensile strength (fmax, elastic limit (fy and total elongation at maximum force [ultimate strain; uniform elongation] (εmax. The three materials were assessed with internationally accepted criteria, such as plastic rotational capacity, necking region and the toughness index (total energy absorbed at uniform elongation. The findings were compared to the properties of three types of conventional reinforcing steel: 500SD, 500N and 500H (EC-2.

    En este trabajo se presentan los diagramas tensióndeformación de un nuevo acero inoxidable con bajo contenido en níquel, un inoxidable convencional AISI 304 y un acero al carbono de uso común en estructuras de hormigón armado. Dicha ductilidad se ha estudiado determinando la tensión máxima (fmax, la tensión en el límite elástico (fy y la deformación bajo carga máxima (εmax. Los tres materiales se han evaluado utilizando criterios aceptados internacionalmente, como son el índice p (capacidad de rotación plástica, el índice A* (área plástica de endurecimiento y el índice de tenacidad Id (energía total absorbida en el punto de alargamiento bajo carga máxima, los resultados obtenidos se han comparado con los aceros convencionales de armaduras 500SD, 500N y 500H (EC-2.

  15. Fatigue behaviour of friction welded medium carbon steel and austenitic stainless steel dissimilar joints

    International Nuclear Information System (INIS)

    Paventhan, R.; Lakshminarayanan, P.R.; Balasubramanian, V.

    2011-01-01

    Research highlights: → Fusion welding of dissimilar metals is a problem due to difference in properties. → Solid state welding process such as friction welding is a solution for the above problem. → Fatigue life of friction welded carbon steel and stainless steel joints are evaluated. → Effect of notch on the fatigue life of friction welded dissimilar joints is reported. → Formation of intermetallic is responsible for reduction in fatigue life of dissimilar joints. -- Abstract: This paper reports the fatigue behaviour of friction welded medium carbon steel-austenitic stainless steel (MCS-ASS) dissimilar joints. Commercial grade medium carbon steel rods of 12 mm diameter and AISI 304 grade austenitic stainless steel rods of 12 mm diameter were used to fabricate the joints. A constant speed, continuous drive friction welding machine was used to fabricate the joints. Fatigue life of the joints was evaluated conducting the experiments using rotary bending fatigue testing machine (R = -1). Applied stress vs. number of cycles to failure (S-N) curve was plotted for unnotched and notched specimens. Basquin constants, fatigue strength, fatigue notch factor and notch sensitivity factor were evaluated for the dissimilar joints. Fatigue strength of the joints is correlated with microstructure, microhardness and tensile properties of the joints.

  16. Corrosion of stainless steels in lead-bismuth eutectic up to 600 °C

    Science.gov (United States)

    Soler, L.; Martín, F. J.; Hernández, F.; Gómez-Briceño, D.

    2004-11-01

    An experimental program has been carried out to understand the differences in the corrosion behaviour between different stainless steels: the austenitic steels 304L and 316L, the martensitic steels F82Hmod, T91 and EM10, and the low alloy steel P22. The influence of oxygen level in Pb-Bi, temperature and exposure time is studied. At 600 °C, the martensitic steels and the P22 steel exhibit thick oxide scales that grow with time, following a linear law for the wet environment and a parabolic law for the dry one. The austenitic stainless steels show a better corrosion behaviour, especially AISI 304L. Under reducing conditions, the steels exhibit dissolution, more severe for the austenitic stainless steels. At 450 °C, all the materials show an acceptable behaviour provided a sufficient oxygen level in the Pb-Bi. At reducing conditions, the martensitic steels and the P22 steel have a good corrosion resistance, while the austenitic steels exhibit already dissolution at the longer exposures.

  17. Corrosion of stainless steels in lead-bismuth eutectic up to 600 deg. C

    International Nuclear Information System (INIS)

    Soler, L.; Martin, F.J.; Hernandez, F.; Gomez-Briceno, D.

    2004-01-01

    An experimental program has been carried out to understand the differences in the corrosion behaviour between different stainless steels: the austenitic steels 304L and 316L, the martensitic steels F82Hmod, T91 and EM10, and the low alloy steel P22. The influence of oxygen level in Pb-Bi, temperature and exposure time is studied. At 600 deg. C, the martensitic steels and the P22 steel exhibit thick oxide scales that grow with time, following a linear law for the wet environment and a parabolic law for the dry one. The austenitic stainless steels show a better corrosion behaviour, especially AISI 304L. Under reducing conditions, the steels exhibit dissolution, more severe for the austenitic stainless steels. At 450 deg. C, all the materials show an acceptable behaviour provided a sufficient oxygen level in the Pb-Bi. At reducing conditions, the martensitic steels and the P22 steel have a good corrosion resistance, while the austenitic steels exhibit already dissolution at the longer exposures

  18. Flat friction tests applied to austenic stainless steels with several surface finish. Analysis of adhesion conditions in friction

    International Nuclear Information System (INIS)

    Coello, J.; Miguel, V.; Ferrer, C.; Calatatyd, A.; Martinez, A.

    2008-01-01

    The main purpose of this work is to evaluate the tribological behaviour of austenic stainless steels AISI 304 with bright surface finishing (B). The assays have been carried out in flat faced dies system with mineral oil of 200 cts viscosity, S 2 Mo grease and in dry conditions. The relationship between friction coefficient and pressure and velocity has been established for the mineral oil as lubricant. In these conditions, a strong adhesive tendency has been found in boundary lubrication regime. The results obtained here, show us that S 2 Mo grease leads to lowest values for the friction coefficient. A minor adhesive behaviour tendency for AISI 316 steel, harder than 304 grades, has been found. A relevant plowing phenomena has been observed for the more critical friction conditions tried out. A surface hardener is produced as a consequence of that. (Author) 19 refs

  19. Effect of solution treatment conditions on the sensitization of austenitic stainless steel

    Directory of Open Access Journals (Sweden)

    XIAOFEI YU

    2009-11-01

    Full Text Available In this study, the impact of the conditions of solution treatment on the degree of sensitization (DOS of austenitic stainless steel (AISI 304 was investigated in detail. The results derived from the electrochemical potentiodynamic reactivation (EPR test indicated that the DOS decreased as the solution treatment temperature and time increased. The reason for this was studied via the SEM morphologies and EDS results, which indicated that the grain size influenced the DOS. Furthermore, cellular automaton (CA was utilized to simulate grain growth, the precipitation of Cr-rich carbides and the three dimensional distribution of the chromium concentration, which vividly illuminated the effect of the grain size on the DOS and was in accordance with the experiment results.

  20. Analysis of the austenitic stainless steel's r-value behavior at elevated temperatures

    Directory of Open Access Journals (Sweden)

    Dušan Arsić

    2015-05-01

    Full Text Available An analysis of the anisotropy properties of austenitic steel AISI 304 (X5CrNi18-10 at elevated temperatures is presented in this paper. Considerations of the anisotropy problems are presented in the theoretical part of the paper, as well as the procedure for determination of the normal anisotropy coefficient. The experimental part of the paper describes the plan, methodology and equipment for testing of material's normal anisotropy and mechanical characteristics. The objective of conducting the experiments was to investigate influence of temperature on normal anisotropy, as well as on the mechanical properties of the considered material. The normal anisotropy was monitored by the coefficient – the so-called "r-value". Besides that, the tensile strength, yield stress and elongation at break were monitored, also. The tests were done on the 0.7 mm thick sheet metal within the temperature range 20 to 700°C.

  1. Effect of welding process, type of electrode and electrode core diameter on the tensile property of 304L austenitic stainless steel

    Directory of Open Access Journals (Sweden)

    Akinlabi OYETUNJI

    2014-11-01

    Full Text Available The effect of welding process, type of electrode and electrode core diameter on the tensile property of AISI 304L Austenitic Stainless Steel (ASS was studied. The tensile strength property of ASS welded samples was evaluated. Prepared samples of the ASS were welded under these three various variables. Tensile test was then carried out on the welded samples. It was found that the reduction in ultimate tensile strength (UTS of the butt joint samples increases with increase in core diameter of the electrode. Also, the best electrode for welding 304L ASS is 308L stainless steel-core electrode of 3.2 mm core diameter. It is recommended that the findings of this work can be applied in the chemical, food and oil industries where 304L ASS are predominantly used.

  2. Precipitate evolution in low-nickel austenitic stainless steels during neutron irradiation at very low dose rates

    International Nuclear Information System (INIS)

    Isobe, Y.; Sagisaka, M.; Garner, F.; Okita, T.

    2007-01-01

    Full text of publication follows: Not all components of a fusion reactor will be subjected to high atomic displacement rates. Some components outside the plasma containment may experience relatively low displacement rates but data generated under long-term irradiation at low dpa rates is hard to obtain. In another study the neutron-induced microstructural evolution in response to long term irradiation at very low dose rates was studied for a Russian low-nickel austenitic stainless steel that is analogous to AISI 304. The irradiated samples were obtained from an out-of-core anti-crush support column for the BN-600 fast reactor with doses ranging from 1.5 to 22 dpa generated at 3x10 -9 to 4x10 -8 dpa/s. The irradiation temperatures were in a very narrow range of 370-375 deg. C. Microstructural observation showed that in addition to voids and dislocations, an unexpectedly high density of small carbide precipitates was formed that are not usually observed at higher dpa rates in this temperature range. These results required us to ask if such unexpected precipitation was anomalous or was a general feature of low-flux, long-term irradiation. It is shown in this paper that a similar behavior was observed in a western stainless steel, namely AISI 304 stainless steel, irradiated at similar temperatures and dpa rates in the EBR-II fast reactor, indicating that irradiation at low dpa rates for many years leads to a different precipitate microstructure and therefore different associated changes in matrix composition than are generated at higher dpa rates. One consequence of this precipitation is a reduced lattice parameter of the alloy matrix, leading to densification that increases in strength with increasing temperature and dose. A. non-destructive method to evaluate these precipitates is under development and is also discussed in this paper. (authors)

  3. Application of laser-produced-plasmas to determination of carbon content in steel; Aplicacion de los plasmas generados por laser a la determinacion de carbono en aceros

    Energy Technology Data Exchange (ETDEWEB)

    Ortiz, M; Aragon, C; Aguilera, J A; Campos, J

    1994-07-01

    This paper describes an analytical method to determine carbon content in solid and molten steel. It is based on the study of the emission spectrum from a Nd-YAG laser produced plasma. The light emitted from the plasma is focused to the entrance slit of a spectrometer and detected by an OMA III system. For every laser pulse an spectral range of 100 A are recorded. With the use of time-resolved spectroscopy a precision of 1.6 % and a detection limit of 65 ppm of carbon content in steel have been obtained. These values are similar to those of other accurate conventional techniques but using optics fiber and laser excitation it is possible to made sample calibrations in hostile environments. Also, as the analysis are made in real time changes in sample composition can be measured without stopping production processes. (Author) 26 refs.

  4. Steel skin - SMC laminate structures for lightweight automotive manufacturing

    Science.gov (United States)

    Quagliato, Luca; Jang, Changsoon; Murugesan, Mohanraj; Kim, Naksoo

    2017-09-01

    In the present research work an innovative material, made of steel skin and sheet molding compound core, is presented and is aimed to be utilized for the production of automotive body frames. For a precise description of the laminate structure, the material properties of all the components, including the adhesive utilized as an interlayer, have been carried out, along with the simple tension test of the composite material. The result have shown that the proposed laminate structure has a specific yield strength 114% higher than 6061 T6 aluminum, 34% higher than 7075 T6 aluminum, 186% higher than AISI 304 stainless steel (30HRC) and 42% than SK5 high-strength steel (52HRC), showing its reliability and convenience for the realization of automotive components. After calibrating the material properties of the laminate structure, and utilizing as reference the simple tension results of the laminate structure, the derived material properties have been utilized for the simulation of the mechanical behavior of an automotive B-pillar. The results have been compared with those of a standard B-pillar made of steel, showing that the MS-SMC laminate structure manifests load and impact carry capacity comparable with those of high strength steel, while granting, at least, an 11% weight reduction.

  5. On the influence of cold work on the oxidation behavior of some austenitic stainless steels: High temperature oxidation

    NARCIS (Netherlands)

    Langevoort, J.C.; Fransen, T.; Gellings, P.J.

    1984-01-01

    AISI 304, 314, 321, and Incoloy 800H have been subjected to several pretreatments: polishing, milling, grinding, and cold drawing. In the temperature range 800–1400 K, cold work improves the oxidation resistance of AISI 304 and 321 slightly, but has a relatively small negative effect on the

  6. Characterization of interference thin films grown on stainless steel surface by alternate pulse current in a sulphochromic solution

    Directory of Open Access Journals (Sweden)

    Rosa Maria Rabelo Junqueira

    2008-12-01

    Full Text Available The aim of this work was to characterize thin interference films grown on the surface of AISI 304 stainless steel for decorative purposes. Films were grown in a sulphochromic solution at room temperature by an alternating pulse current method. The morphology and chemical state of the elements in the films were investigated by field emission scanning electron microscopy (FESEM, atomic force microscopy (AFM, glow discharge optical emission spectrometry (GDOES, and infrared Fourier transform spectroscopy (FTIR. Depth-sensing indentation (DSI experiments and wear abrasion tests were employed to assess the mechanical resistance of the films. The coloration process resulted in porous thin films which increased the surface roughness of the substrate. The interference films mainly consisted of hydrated chromium oxide containing iron. Increasing film thickness produced different colors and affected the mechanical properties of the coating-substrate system. Thicker films, such as those producing gold and green colors, were softer but more abrasion resistant.

  7. Application of the EPR technique in welded couplings in 08X18H10T (AISI 321) stainless steel

    International Nuclear Information System (INIS)

    Fuentes, D.A.; Menendez, C.M.; Dominguez, H.; Sendoya, F.

    1993-01-01

    Stainless steel samples, one AISI 304 and the other 08X18H10T of Soviet origin (equivalent to AISI 320) were welded for the TIG method, submitted to a thermal treatment in order to its sensitization against the intergranular corrosion, then the samples were submitted to the EPR technique in order to establish the sensitization degree which is an indicative of susceptibility to intergranular corrosion. The result were corroborated by two different methodologies, the ASTM A262 standard and the soviet standard GOST 6032-89. The state of the tested surface was analyzed using optical microscopy in order to quantify the number of pricking since its presence disturbs the normalized charge, Pa. (Author)

  8. Production and characterization of stainless steel based Fe-Cr-Ni-Mn-Si(-Co) shape memory alloys

    International Nuclear Information System (INIS)

    Otubo, J.

    1995-01-01

    It is well known that the Fe based alloys can exhibit shape memory effect due to the γ to ε martensitic transformation. The effect may not be as striking as observed in the NiTi alloy but it might become attractive from the practical point of view. In this work, two compositions of Fe-Cr-Ni-Mn-Si(-Co) stainless steel based shape memory alloy, prepared by the VIM technique, will be presented. The results are good with shape recovery of 95% for a pre-strain of 4% after some training cycles. In terms of workability the alloys produced are worse than the usual AISI304. However, adjusting the thermo-mechanical processing, it is perfectly possible to produce wire as thin as 1,20mm in dia. or down. (orig.)

  9. The residual stress distribution in welded pipe inner surface of stainless steel from the nuclear power plant in Ringhals

    International Nuclear Information System (INIS)

    Larsson, L.E.

    1984-06-01

    The axial residual stress distribution on the inner surface of welded pipes of stainless steel SS 2333 (AISI 304) have been measured using the X-ray diffraction technique. Four halves of two pipes with the outer diameter of 114 mm and wall thickness of 10 mm were investigated. The result on the pipe inner surface shows compressive stresses in the weld metal and tensile stresses within a region between 8-23 mm with a maximum of 180MPa at a distance of 17 mm from the weld centerline. The maximum axial and circumferential residual stresses on the pipe outer surface are of the magnitude of 100 MPa. By cutting the pipes into two halves these stresses are relaxed by about 35 MPa. (author)

  10. Desarrollo de aplicaciones web

    OpenAIRE

    Luján Mora, Sergio

    2010-01-01

    Agradecimientos 1. Introducción a las aplicaciones web 2. Instalación del servidor 3. Diseño de páginas web 4. Formato estructurado de texto: XML 5. Contenido dinámico 6. Acceso a bases de datos: JDBC 7. Servicios web 8. Utilización y mantenimiento 9. Monitorización y análisis Bibliografía GNU Free Documentation License

  11. Application of the gamma rays backscattering for determining the quantity of steel; Aplicacion de la tecnica de retrodispersion de los rayos gamma para determinar la cuantia del acero

    Energy Technology Data Exchange (ETDEWEB)

    Huapaya P, B F

    1996-11-01

    This work tries to purpose a methodology based on the nuclear technology available in the country, for measuring the position and diameter of the reinforcing rods placed in reinforced concrete structures. The technique of gamma backscattering that utilizes the changes of density was used for determining the presence of steel (average density of concrete 2,5 g/cm{sup 3} and steel 7,8 g/cm{sup 3}). The concrete test tubes of different resistances were prepared with diverse concentrations into the aggregates as crushed rock and coarse sand, and also with three steel rods of 0,5 inch separated by 4 inches among themselves. The source Cs-137 of 20 mCi in activity was a monoenergetic radioisotope of the element Cs from 662 KeV. The source was placed in a lead shield with a hole which generates a collimator beam of 2 mm. The detector was one type of scintillation (INa-Tl) 2 x 2 inch; it was sealed with lead and had a hole of 10 mm which worked as collimator. The shield was placed in an angle of 15 degrees over concrete surface in order to pick up the backscattering gamma rays by the concrete. The test tube was displaced over a little car affixed to a endless screw which permitted to reproduce displacements of 0,25 inch. The data recording was realized through a multichannel of 1024 channels where was accounted the number of counts viewed under the backscattering spectrum by the concrete. It is possible to determine the position and diameter of the steel rod into concrete, changing the parameters of detector collimator source, distance source-detector and type of concrete. Furthermore, it was shown that this same equipment can measure the density of the concrete. The applications of this equipment are used in the inspection works where it is necessary to make a non-destructive control of quality about the structure of building. (author). 7 refs., 46 tabs., 24 figs.

  12. RESEARCH OF THE ENTRANCE ANGLE EFFECT ON THE REFLECTANCE SPECTRA OF THE STAINLESS STEEL SURFACE OXIDIZED BY PULSED LASER RADIATION

    Directory of Open Access Journals (Sweden)

    V. P. Veiko

    2016-05-01

    Full Text Available Subject of Research.Oxide films on the metal surfaces can be obtained both by surface-uniform infrared heating and local laser treatment e.g. by sequence of nanosecond laser pulses. Due to interference in created films the coloration of treated area is observed. The present work shows the results of spectrophotometric measurements for various light entrance angles in the range of 10-60°. Method. AISI 304 stainless steel plates were oxidized by two methods: in muffle furnace FM - 10 (Т= 500-600° С, t = 5-7 min. and at line-by-line scanning by sequence of nanosecond laser pulses (λ = 1.06 μm, τ =100 ns, r = 25 μm,q=2.91∙107 W/cm2, Nx = 30, Ny = 1. Surface research in optical resolution was realized by Carl Zeiss Axio Imager A1M. Reflectance spectra were obtained with spectrophotometer Lambda Perkin 1050 with integrating sphere at different fixed light incidence angles. Topographic features were detected by scanning probe microscopy investigation with NanoEducator equipment. Main Results. The quantitative surface geometry characteristics of AISI 304 stainless steel patterns treated by different methods are obtained. It was found that the increase of light entrance angle has no influence on the form of reflection coefficient dependence from a wavelength, but a blue-shift occurs especially for the case of laser treatment. This difference can be caused by surface topology formed by laser heating and variety of oxide film thickness. This effect results in more significant change in observed sample color for laser treatment then for infrared heating. Practical Relevance. The results obtained in the present work can be used to implement a new element of product protection against forgery with the product marking.

  13. Neurofeedback, aplicaciones y eficacia

    OpenAIRE

    Fajardo, Alexandra; Guzmán, Ana Lucía

    2016-01-01

    El objetivo del estudio que se informa fue describir la técnica de neurofeedback, sus aplicaciones y usos, como así también determinar su eficacia a lo largo de los estudios revisados. De esta forma se encuentra la compilación de 53 artículos científicos acerca de la técnica, que describen cómo los autores han demostrado su funcionalidad, cuando se trata de proyectar de manera tangible el rendimiento de algún tipo de población para la posterior formulación de un tratamiento o intervención par...

  14. Wavelets y sus aplicaciones

    OpenAIRE

    Castro, Liliana Raquel; Castro, Silvia Mabel

    1995-01-01

    Se presenta una introducción a la teorfa de wavelets. Ademas, se da una revisión histórica de cómo fueron introducidas las wavelets para la representación de funciones. Se efectúa una comparación entre la transformada wavelet y la transformada de Fourier. Por último, se presentan también algunas de los múltiples aplicaciones de esta nueva herramienta de análisis armónico.

  15. On the measurement of the stacking-fault energies of face centered cubic metal and austenitic stainless steels by X-ray diffraction

    International Nuclear Information System (INIS)

    Borges, J.F.A.

    1985-01-01

    An X-rays diffraction method was applied to measure the Stacking-Fault Energies (SFE) of the AISI 304, AISI 316, AISI 347 and DIN-WERKSTOFF 1.4970 Austenitic Stainless Steels. The SFE determination plays an important role in the research of the mechanical behaviour of the Metal and Alloys, their deformation mechanisms, stability of microstructure amd electronic configuration. The method is based on the relationship between the SFE and the ratio of the Mean Square Strain to the Stacking-Fault probability. The Mean Square Strain was evaluated by Fourier Analysis of X-rays Diffraction profiles, corrected to reduce instrumental effects, followed by the application of the Warren-Averbach method to the Fourier Coefficients. The Stacking-Fault probabilities were derived from the changes of peak separations between cold-worked and annealed specimens. (author) [pt

  16. Measurement of carbon activity in sodium by Fe-Mn 20% alloy, and by strainless austenitic steel 304L and 316L

    International Nuclear Information System (INIS)

    Oberlin, C.; Saint Paul, P.; Baque, P.; Champeix, L.

    1980-01-01

    Precise knowledge of carbon activity in sodium used as coolant in fast breeder reactors, is essential for continuous survey of carburization-decarburization processes. Carbon activity can be periodically surveyed by measuring the carbon concentration or by hot trap like metal alloy strip placed in sodium loop. In fact, in equilibrium, activity of carbon in sodium is equal to the activity in metal alloy. Thus if the relation between concentration of carbon and it activity in the alloy is known, it is possible to estimate the activity of carbon in sodium. Materials to be used should have high solubility in carbon at the needed temperature. They should quickly attain equilibrium with sodium and they should not contain impurities that can affect the results. Materials chosen according to these criteria were Fe-Mn 20%, stainless austenitic steel AISI 304L and 316L

  17. Stress corrosion cracking of austenitic stainless steels in PWR primary water: an update of metallurgical investigations performed on French withdrawn components

    International Nuclear Information System (INIS)

    Boursier, J.M.; Gallet, S.; Rouillon, Y.; Bordes, P.

    2002-01-01

    Austenitic stainless steels (AISI 304, 304L, 316 and 316L) are largely used in Nuclear Power Plants because of their good resistance to corrosion and their satisfactory mechanical properties. Nevertheless, on various French PWR Nuclear Power Plants, several cases of corrosion have been encountered in auxiliary circuit portions where deleterious species and oxygen can be present. This paper focuses on the metallurgical investigations performed on pulled out components such as Canopy welds or 'dead legs' (auxiliary circuit portions connected to the main primary loops) in terms of cracking locations and degradation parameters. In addition, some comparisons between Nuclear Power Plant feedback and fundamental research and development studies are discussed, particularly in the scope of temperature, microstructure, stresses (applied and residual) and medium responsible for the degradation. (authors)

  18. Biofilm formation by Listeria monocytogenes on stainless steel surface and biotransfer potential

    Directory of Open Access Journals (Sweden)

    Maíra Maciel Mattos de Oliveira

    2010-03-01

    Full Text Available An experimental model was proposed to study biofilm formation by Listeria monocytogenes ATCC 19117 on AISI 304 (#4 stainless steel surface and biotransfer potential during this process. In this model, biofilm formation was conducted on the surface of stainless steel coupons, set on a stainless steel base with 4 divisions, each one supporting 21 coupons. Trypic Soy Broth was used as bacterial growth substrate, with incubation at 37 ºC and stirring of 50 rpm. The number of adhered cells was determined after 3, 48, 96, 144, 192 and 240 hours of biofilm formation and biotransfer potential from 96 hours. Stainless steel coupons were submitted to Scanning Electron Microscopy (SEM after 3, 144 and 240 hours. Based on the number of adhered cells and SEM, it was observed that L. monocytogenes adhered rapidly to the stainless steel surface, with mature biofilm being formed after 240 hours. The biotransfer potential of bacterium to substrate occurred at all the stages analyzed. The rapid capacity of adhesion to surface, combined with biotransfer potential throughout the biofilm formation stages, make L. monocytogenes a potential risk to the food industry. Both the experimental model developed and the methodology used were efficient in the study of biofilm formation by L. monocytogenes on stainless steel surface and biotransfer potential.

  19. Biofilm formation by Listeria monocytogenes on stainless steel surface and biotransfer potential.

    Science.gov (United States)

    de Oliveira, Maíra Maciel Mattos; Brugnera, Danilo Florisvaldo; Alves, Eduardo; Piccoli, Roberta Hilsdorf

    2010-01-01

    An experimental model was proposed to study biofilm formation by Listeria monocytogenes ATCC 19117 on AISI 304 (#4) stainless steel surface and biotransfer potential during this process. In this model, biofilm formation was conducted on the surface of stainless steel coupons, set on a stainless steel base with 4 divisions, each one supporting 21 coupons. Trypic Soy Broth was used as bacterial growth substrate, with incubation at 37 °C and stirring of 50 rpm. The number of adhered cells was determined after 3, 48, 96, 144, 192 and 240 hours of biofilm formation and biotransfer potential from 96 hours. Stainless steel coupons were submitted to Scanning Electron Microscopy (SEM) after 3, 144 and 240 hours. Based on the number of adhered cells and SEM, it was observed that L. monocytogenes adhered rapidly to the stainless steel surface, with mature biofilm being formed after 240 hours. The biotransfer potential of bacterium to substrate occurred at all the stages analyzed. The rapid capacity of adhesion to surface, combined with biotransfer potential throughout the biofilm formation stages, make L. monocytogenes a potential risk to the food industry. Both the experimental model developed and the methodology used were efficient in the study of biofilm formation by L. monocytogenes on stainless steel surface and biotransfer potential.

  20. Enhanced mechanical behaviors of gradient nano-grained austenite stainless steel by means of ultrasonic impact treatment

    Directory of Open Access Journals (Sweden)

    Xinjun Yang

    Full Text Available The gradient nano-grained (GNG structure was formed on the top layer of AISI 304 in the presence of coarse grains (CG by means of ultrasonic impact treatment (UIT. The impact velocity was 5 m/s and the coverage changed from 3000% to 9000% in order to obtain the microstructure GNG/CG materials. The tensile test and small punch test (SPT were further carried out in order to investigate the mechanical behaviors of the GNG/CG 304 at the different stress states. The results indicated that the yield strength of GNG/CG 304 obtained by tensile test and SPT increased at the small expense of ductility. The stress triaxiality T played an important role in the deformation behavior of GNG/CG 304. An increased T-value in the region of biaxial stretching of small punch specimen (T = 2/3 led to an improved ductility compared with that noted in the case of uniaxial tensile specimen. The strain rate sensitivity m of GNG/CG 304 was 0.0468 that was estimated to be 25-fold greater than the coarse material. The yield strength of GNG/CG 304 at 400 °C was 1.6-fold greater than the coarse material at ambient temperature due to the thermal stability of the GNG layer. Thus, the GNG structure could improve the comprehensive mechanical performances of AISI 304 with a balance of strength and ductility. Keywords: GNG structure, Mechanical behaviors, Small punch test, Ultrasonic impact treatment, Austenite stainless steel

  1. High cycle fatigue of austenitic stainless steels

    International Nuclear Information System (INIS)

    Gauthier, J.P.; Lehmann, D.; Picker

    1990-01-01

    This study concerns the evaluation of material data to be used in LMFBR design codes. High cycle fatigue properties of three austenitic stainless steels are evaluated: type AISI 316 (UKAEA tests), type AISI 316L (CEA tests) and type AISI 304 (Interatom tests). The data on these steels comprised some 550 data points from 14 casts. This data set covered a wide range of testing parameters: temperature from 20-625 0 C, frequency from 1-20 000 Hz, constant amplitude and random fatigue loading, with and without mean stress, etc. However, the testing conditions chosen by the three partners differed considerably because they had been fixed independently and not harmonized prior to the tests. This created considerable difficulties for the evaluations. Experimental procedures and statistical treatments used for the three subsets of data are described and discussed. Results are presented in tables and graphs. Although it is often difficult to single out the influence of each parameter due to the different testing conditions, several interesting conclusions can be drawn: The HCF properties of the three steels are consistent with the 0.2% proof stress, the fatigue limit being larger than the latter at temperatures above 550 0 C. The type 304 steel has lower tensile properties than the two other steels and hence also lower HCF properties. Parameters which clearly have a significant effect of HCF behaviour are mean stress or R-ratio (less in the non-endurance region than in the endurance region), temperature, cast or product. Other parameters have probably a weak or no effect but it is difficult to conclude due to insufficient data: environment, specimen orientation, frequency, specimen geometry

  2. Comparative study between two austenitic steels with the EPR (Electrochemical Potentiokinetic Reactivation) technique

    International Nuclear Information System (INIS)

    Guillen M, A.N.

    1997-01-01

    In the mid 19704s, the intergranular corrosion with stress corrosion cracking (IGSCC) have been identified as a greater problem in Boiling Water Reactors BWR in several places of the world. The Electrochemical Potentiokinetic Reactivation - Single Loop (EPR-SL) test and the Double Loop (EPR-DL) test, were developed as methods for measuring the Degree of Sensitization (DOS), show sensitised materials at subject to Intergranular Corrosion. In Mexico, the Laguna Verde4s reactor is BWR type and many of its principal components was built with AISI 304 stainless steels, while that in VVER reactors as well as Juragua4s reactor in Cuba is used 321 Stainless stell in its Russian equivalent designation 08Ch18N10T. In this work, were studied 304 and 08Ch18N10T stainless steels by means of EPR-SL, EPR-DL and ASTM A-262 techniques, they have been found a good correlation for 304 steel but not in 08Ch18N10T steel and was proposed one modification in the criterion by the evaluation on the sensitisation in this steels. Finally, both materials were welded with procedures used in the nuclear industry, by Slow Strain Rate Test (SSRT) to determine the Stress Corrosion Cracking SCC susceptibility, and subsequently the susceptibility to localized corrosion was studied by means of Cyclic Polarization test and the uniform corrosion rate in a solution with chlorides by the Tafel plot, Potentiodynamic Anodic Polarization Resistance. (Author)

  3. Determination of delta ferrite volumetric fraction in austenitic stainless steel

    International Nuclear Information System (INIS)

    Almeida Macedo, W.A. de.

    1983-01-01

    Measurements of delta ferrite volumetric fraction in AISI 304 austenitic stainless steels were done by X-ray diffraction, quantitative metallography (point count) and by means of one specific commercial apparatus whose operational principle is magnetic-inductive: The Ferrite Content Meter 1053 / Institut Dr. Foerster. The results obtained were comparated with point count, the reference method. It was also investigated in these measurements the influence of the martensite induced by mechanical deformation. Determinations by X-ray diffraction, by the ratio between integrated intensities of the ferrite (211) and austenite (311) lines, are in excelent agreement with those taken by point count. One correction curve for the lectures of the commercial equipment in focus was obtained, for the range between zero and 20% of delta ferrite in 18/8 stainless steels. It is demonstrated that, depending on the employed measurement method and surface finishing of the material to be analysed, the presence of martensite produced by mechanical deformation of the austenitic matrix is one problem to be considered. (Author) [pt

  4. Determination of delta ferrite volumetric fraction in austenitic stainless steels

    International Nuclear Information System (INIS)

    Almeida Macedo, W.A. de.

    1983-01-01

    Measurements of delta ferrite volumetric fraction in AISI 304 austenitic stainless steels were done by X-ray difraction, quantitative metallography (point count) and by means of one specific commercial apparatus whose operational principle is magnetic-inductive: The Ferrite Content Meter 1053 / Institut Dr. Forster. The results obtained were comparated with point count, the reference method. It was also investigated in these measurements the influence of the martensite induced by mechanical deformation. Determinations by X-ray diffraction, by the ratio between integrated intensities of the ferrite (211) and austenite (311) lines, are in excelent agreement with those taken by point count. One correction curve for the lectures of the commercial equipment in focus was obtained, for the range between zero and 20% of delta ferrite in 18/8 stainless steels. It is demonstrated that, depending on the employed measurement method and surface finishing of the material to be analysed, the presence of martensite produced by mechanical deformation of the austenitic matrix is one problem to be considered. (Author) [pt

  5. TiN coating on steel by pulsed capillary discharge

    International Nuclear Information System (INIS)

    Avaria, G; Favre, M; Bhuyan, H; Wyndham, E; Kelly, H; Grondona, D; Marquez, A

    2006-01-01

    The characteristic geometry of a pulsed capillary discharge (PCD)[1] establishes natural conditions for the formation of plasma jets, which expand in the chamber's neutral gas. A locally stored capacitor, coaxial with the capillary, is pulse charged to a maximum of -10kV, giving a current pulse of ∼10ns, ∼2kA. The discharge is operated in nitrogen, in a continuous pulsing mode, at a frequency of 50 Hz and pressures of 0.3 to 1 Torr. The coating produced by these plasma jets on substrates of AISI 304 stainless steel have been studied. The chamber's anode is made of titanium, which interacts with the nitrogen plasma producing TiN coatings on the substrates. The results are presented for the plasma characterization at different discharge pressures and times, as well as SEM, EDS and AFM analysis of deposits made. This characterization was carried out using Langmuir double probes, which provide data on the electronic temperature and density in the plasma jet. At the same time spectrographic studies of the plasma were carried out, and the presence of ionized atoms of titanium and nitrogen were observed. An inverse relation between the pressure of nitrogen present in the chamber and the thickness of the coating over steel was found, as well as a direct relationship between the temperature and plasma densities with the thickness of the deposit (CW)

  6. Influence of corrosion on the morphology and structure of ZrO{sub x}N{sub y}−ZrN coatings deposited on stainless steel

    Energy Technology Data Exchange (ETDEWEB)

    Cubillos, G.I., E-mail: gcubillos@unal.edu.co [Departamento de Química, Grupo de Materiales y Procesos Químicos, Universidad Nacional de Colombia, Bogotá (Colombia); Romero, E., E-mail: erromerom@unal.edu.co [Departamento de Química, Grupo de Materiales y Procesos Químicos, Universidad Nacional de Colombia, Bogotá (Colombia); Alfonso, J.E. [Grupo de Ciencia de Materiales y Superficies, Departamento de Física, Universidad Nacional de Colombia, AA 14490 Bogotá (Colombia)

    2016-06-15

    Morphological and structural changes of zirconium nitride and oxynitride thin films (ZrO{sub x}N{sub y}/ZrN) deposited via DC magnetron sputtering on stainless steel substrates (AISI 316L, 304LS, and 2205) in a reactive N{sub 2} and N{sub 2}/O{sub 2} atmosphere mixed with argon were studied. The crystallographic structures of the films were established through X-ray diffraction (XRD). The morphology was evaluated via scanning electron microscopy (SEM) and atomic force microscopy (AFM), and the corrosion resistance was evaluated using electrochemical techniques based on linear polarization (PL). The XRD analysis showed that the films were composed of cubic ZrO{sub x}N{sub y} and monoclinic ZrO{sub 2}. The electrochemical test showed that there was corrosion because of pitting phenomena and delamination in the coating deposited on AISI 2205 and AISI 304LS substrates. For AISI 316L, the damage generated by the corrosive solution was less. On the various substrates, an increase in the films' roughness was observed after the corrosion test. - Highlights: • We study the crystallographic change of ZrOxNy thin films after corrosion. • It was evaluated the morphological change of the coating after corrosion in NaCl solution. • The ZrOxNy films grew in the cubic phase and preferentially oriented along the (222) plane. • For AISI 316L, the damage generated by the corrosive solution was less, compared with AISI 304LS and AISI 2205.

  7. Comparison of material property specifications of austenitic steels in fast breeder reactor technology

    International Nuclear Information System (INIS)

    Vanderborck, Y.; Van Mulders, E.

    1985-01-01

    Austenitic stainless steels are very widely used in components for European Fast Breeder Reactors. The Activity Group Nr.3 ''Materials'', within Working Group ''Codes and Standards'' of the Fast Reactor Co-Ordination Committee of the European Communities, has decided to initiate a study to compare the material property specifications of the austenitic stainless steel used in the European Fast Breeder Technology. Hence, this study would allow one to view rapidly the designation of a particular steel grade in different European countries and to compare given property values for a same grade. There were dissimilarities, differences or voids appear, it could lead to an attempt to complete and/or to uniformize the nationally given values, so that on a practical level interchangeability, availability and use ease design and construction work. A selection of the materials and of their properties has been made by the Working Group. Materials examined are Stainless Steel AISI 304, 304 L, 304 LN, 316, 316 L, 316 LN, 316''Ti stab.'', 316''Nb stab''., 321, 347

  8. Influence of Citric Acid on the Metal Release of Stainless Steels

    Energy Technology Data Exchange (ETDEWEB)

    Mazinanian, N.; Wallinder, I. Odnevall; Hedberg, Y. S. [KTH Royal Institute of Technology, School of Chemical Science and Engineering, Department of Chemistry, Division of Surface and Corrosion Science, Stockholm (Sweden)

    2015-08-15

    Knowledge of how metal releases from the stainless steels used in food processing applications and cooking utensils is essential within the framework of human health risk assessment. A new European standard test protocol for testing metal release in food contact materials made from metals and alloys has recently been published by the Council of Europe. The major difference from earlier test protocols is the use of citric acid as the worst-case food simulant. The objectives of this study were to assess the effect of citric acid at acidic, neutral, and alkaline solution pH on the extent of metal release for stainless steel grades AISI 304 and 316, commonly used as food contact materials. Both grades released lower amounts of metals than the specific release limits when they were tested according to test guidelines. The released amounts of metals were assessed by means of graphite furnace atomic absorption spectroscopy, and changes in the outermost surface composition were determined using X-ray photoelectron spectroscopy. The results demonstrate that both the pH and the complexation capacity of the solutions affected the extent of metal release from stainless steel and are discussed from a mechanistic perspective. The outermost surface oxide was significantly enriched in chromium upon exposure to citric acid, indicating rapid passivation by the acid. This study elucidates the effect of several possible mechanisms, including complex ion- and ligand-induced metal release, that govern the process of metal release from stainless steel under passive conditions in solutions that contain citric acid.

  9. In situ ellipsometric investigation of stainless steel corrosion behavior in buffered solutions with amino acids

    International Nuclear Information System (INIS)

    Vinnichenko, M.V.; Pham, M.T.; Chevolleau, T.; Poperenko, L.V.; Maitz, M.F.

    2003-01-01

    The corrosion of metals is associated both with a release of ions and changes in optical surface properties. In this study, these two effects were correlated by a potentiodynamic corrosion test and in situ probing of the surface by ellipsometry. The studies were carried out with stainless steel (SS) AISI 304 and 316 in phosphate buffered saline (PBS) and in Dulbecco's modified minimal essential medium (DMEM) at pH 7.4. In both media, 304 steel is more susceptible to corrosion than 316 grade. The 316 steel shows a higher corrosion potential and higher corrosion current density in PBS than in DMEM, for 304 steel this behavior is vice versa. Ellipsometry demonstrated a higher sensitivity than potentiodynamics to surface modification in the cathodic area. In DMEM the removal of a surface layer at negative potential and a further repassivation with increasing potential was characteristic. In PBS a surface layer started to grow immediately. X-ray photoelectron spectra of this layer formed in PBS are consistent with iron phosphate. Its formation is inhibited in DMEM; the presence of amino acids is discussed as the reason

  10. Steel

    International Nuclear Information System (INIS)

    Zorev, N.N.; Astafiev, A.A.; Loboda, A.S.; Savukov, V.P.; Runov, A.E.; Belov, V.A.; Sobolev, J.V.; Sobolev, V.V.; Pavlov, N.M.; Paton, B.E.

    1977-01-01

    Steels also containing Al, N and arsenic, are suitable for the construction of large components for high-power nuclear reactors due to their good mechanical properties such as good through-hardening, sufficiently low brittleness conversion temperature and slight displacement of the latter with neutron irradiation. Defined steels and their properties are described. (IHOE) [de

  11. Intergranular Corrosion Behavior of Low-Nickel and 304 Austenitic Stainless Steels

    Science.gov (United States)

    Bansod, Ankur V.; Patil, Awanikumar P.; Moon, Abhijeet P.; Khobragade, Nilay N.

    2016-09-01

    Intergranular corrosion (IGC) susceptibility for Cr-Mn austenitic stainless steel and 304 austenitic stainless steel (ASS) was estimated using electrochemical techniques. Optical and SEM microscopy studies were carried out to investigate the nature of IGC at 700 °C with increasing time (15, 30, 60, 180, 360, 720, 1440 min) according to ASTM standard 262 A. Quantitative analysis was performed to estimate the degree of sensitization (DOS) using double loop electrochemical potentiokinetic reactivation (DLEPR) and EIS technique. DLEPR results indicated that with the increase in thermal aging duration, DOS becomes more severe for both types of stainless steel. The DOS for Cr-Mn ASS was found to be higher (65.12% for 1440 min) than that of the AISI 304 ASS (23% for 1440 min). The higher degree of sensitization resulted in lowering of electrical charge capacitance resistance. Chronoamperometry studies were carried out at a passive potential of 0.4 V versus SCE and was observed to have a higher anodic dissolution of the passive film of Cr-Mn ASS. EDS studies show the formation of chromium carbide precipitates in the vicinity of the grain boundary. The higher Mn content was also observed for Cr-Mn ASS at the grain boundary.

  12. Seguridad de las aplicaciones web

    OpenAIRE

    Luján Mora, Sergio

    2016-01-01

    Conferencia "Seguridad de las aplicaciones web" impartida en las III Jornadas Informáticas - UTE 2016 en la Facultad de Ciencias de la Ingeniería e Industrias de la Universidad Tecnológica Equinoccial (Quito, Ecuador) el 5 de julio de 2016.

  13. Production and qualification for fusion applications, a steel of low activity ferritic-martensitic ASTURFER; Produccion y cualificacion, para aplicaciones de fusion, de un acero de baja actividad ferritico-martensitico, ASTURFER

    Energy Technology Data Exchange (ETDEWEB)

    Moran, A.; Belzunce, J.; Artimez, J. M.

    2011-07-01

    This article details the work carried out in the design and development pilot plant scale of a steel ferritic-martensitic of reduced activity, Asturfer, with a chemical composition and metallurgical properties similar to steel Eurofer. We describe the different stages of steel production and the results of the characterizations made in the context of an extensive test program.

  14. Low cycle fatigue studies on a type 304 stainless steel

    International Nuclear Information System (INIS)

    Bhanu Sankara Rao, K.; Valsan, M.; Sandhya, R.; Ray, S.K.; Rodriguez, P.

    The effects of temperature and strain rate on the low cycle fatigue behaviour were investigated for an AISI 304 stainless steel under total axial strain control mode at 823 and 923 K. The fatigue life was strongly dependent on cyclic deformation rate for this material at these temperatures, decreasing markedly with decreasing strain rate. The cyclic stress-strain response recorded in the form of hysterisis loops exhibited serrations at low strain rates at 823 and 923 K. Cyclic stress-strain response at 823 K has shown an increase in saturation stress and decrease in plastic strain range whereas there is an increase in plastic strain range without marked variation in saturation stress level at 923 K with decreasing strain rate. It has been observed that there are three simultaneous effects namely environment, creep and cyclic strain ageing which contribute to the observed degradation in fatigue life at low strain rates. At 823 K, where the creep damage as well as environmental damage is relatively small, the fatigue life is considered mainly to be affected by dynamic strain ageing effect which depends on strain rate. At 923 K, on the other hand, the strain rate dependence of fatigue life is considered to be determined by the combination of creep and environmental effects. Deformation and fracture studies have also confirmed that the wedge type crack propagation is accelerated by oxidation effect. (author)

  15. Comparative study between two austenitic steels with the EPR (Electrochemical Potentiokinetic Reactivation) technique.; Estudio comparativo entre dos aceros austeniticos mediante la tecnica EPR (Reactivacion Electroquimica Potenciocinetica)

    Energy Technology Data Exchange (ETDEWEB)

    Guillen M, A N

    1997-09-01

    In the mid 19704s, the intergranular corrosion with stress corrosion cracking (IGSCC) have been identified as a greater problem in Boiling Water Reactors BWR in several places of the world. The Electrochemical Potentiokinetic Reactivation - Single Loop (EPR-SL) test and the Double Loop (EPR-DL) test, were developed as methods for measuring the Degree of Sensitization (DOS), show sensitised materials at subject to Intergranular Corrosion. In Mexico, the Laguna Verde4s reactor is BWR type and many of its principal components was built with AISI 304 stainless steels, while that in VVER reactors as well as Juragua4s reactor in Cuba is used 321 Stainless stell in its Russian equivalent designation 08Ch18N10T. In this work, were studied 304 and 08Ch18N10T stainless steels by means of EPR-SL, EPR-DL and ASTM A-262 techniques, they have been found a good correlation for 304 steel but not in 08Ch18N10T steel and was proposed one modification in the criterion by the evaluation on the sensitisation in this steels. Finally, both materials were welded with procedures used in the nuclear industry, by Slow Strain Rate Test (SSRT) to determine the Stress Corrosion Cracking SCC susceptibility, and subsequently the susceptibility to localized corrosion was studied by means of Cyclic Polarization test and the uniform corrosion rate in a solution with chlorides by the Tafel plot, Potentiodynamic Anodic Polarization Resistance. (Author).

  16. The influence of interstitial impurities on temperature ranges of deuterium retention in austenitic stainless steel 18Cr10NiTi

    International Nuclear Information System (INIS)

    Neklyudov, I.M.; Morozov, O.M.; Kulish, V.G.; Zhurba, V.I.; Galytsky, A.G.; Piatenko, E.V.

    2009-01-01

    The influence of nitrogen, oxygen and helium on the temperature range of deuterium retention in 18Cr10NiTi stainless steel (of AISI304L type) has been investigated. It is demonstrated that the introduction of oxygen, nitrogen or helium into 18Cr10NiTi steel extends the upper limit in the high-temperature range of deuterium retention. It has been found that for 18Cr10NiTi stainless steel, pre-irradiated with helium ions, the increase in the temperature range of deuterium retention occurs in steps: on attainment of helium concentration of ∼0.5 at.% He the temperature range increases by ∼100 K, and on attainment of helium concentration of ∼2.5 at.% He the temperature range increases by ∼350 K. The introduction of oxygen into 18Cr10NiTi stainless steel results in the increase of the temperature range of deuterium retention in the direction of rise in temperature. In the deuterium thermodesorption spectrum, this manifests itself by the occurrence of an additional low-amplitude peak with the maximum temperature T m ∼ 560 K. The introduction of nitric impurity into 18Cr10NiTi stainless steel results in the extension of the temperature range of deuterium retention towards higher temperatures.

  17. Interactive Influence on Void Swelling in 300 Series Stainless Steels of Coupled Gradients in Temperature and DPA Rate

    International Nuclear Information System (INIS)

    Garner, F.

    2007-01-01

    Full text of publication follows: Recently, experimental evidence has accumulated that demonstrates that the dependence of swelling in austenitic steels on dpa rate has been strongly underestimated. In development of swelling correlations for both fusion and fission reactor applications the dpa rate is frequently but inadvertently incorporated into the temperature dependence. This inability to separate the separate dependencies of dpa rate and temperature is closely associated with the coupling of gradients in neutron flux-spectra and irradiation temperature along the axial length of components, especially for relatively small cores. In order to demonstrate the separate action of dpa rate and temperature, previously unpublished swelling data are presented from hexagonal ducts, fuel pins and pressurized tubes irradiated in EBR-II, all possessing both axial and radial gradients in dpa rate. Annealed AISI 304 components were chosen to avoid complications of precipitation found in other alloys such as AISI 316 or PCA. Since this steel never develops multiple-peak swelling behavior and experiences very little precipitation at high dpa rates, it use in this effort is ideal for separation of environmental variables. It is demonstrated that the transient regime of void selling is increased by increasing dpa rate and by decreasing temperature. It is also shown that the combined effect of dpa rate and temperature distribution along the length of any given structural component produces a well defined, scatter-free 'swelling loop' vs. dpa that uniquely allows estimation and separation of the separate dependencies of swelling on temperature and dpa rate. One consequence of the derived flux dependence is that components subject to a dpa rate gradient in general suffer much less distortion than predicted by equations that do not explicitly incorporate a dependence on dpa rate. It is also shown that over a wide range of irradiation conditions the terminal steady-state swelling

  18. Analysis of the strain induced martensitic transformation in austenitic steel subjected to dynamic perforation

    Directory of Open Access Journals (Sweden)

    Zaera R.

    2012-08-01

    Full Text Available An experimental and numerical analysis on the martensitic transformation in AISI 304 steel sheets subjected to perforation by conical and hemispherical projectiles is reported. Two target thicknesses are considered, 0.5 and 1.0 mm, and impact velocities range from 35 to 200 m/s. The perforation mechanisms are identified and the effect of the projectile nose-shape on the ability of the target for energy absorption is evaluated. Martensite has been detected in all the impacted samples and the role played by the projectile nose-shape on the transformation is highlighted. A 3D model implemented in ABAQUS/Explicit allowed to simulate the perforation tests. The material is defined through a constitutive description developed by the authors to describe the strain induced martensitic transformation taking place in metastable austenitic steels at high strain rates. The numerical results are compared with the experimental evidence and satisfactory matching is obtained. The numerical model succeeds in describing the perforation mechanisms associated to each projectile-target configuration analysed.

  19. Study of the Corrosion Resistance of Austenitic Stainless Steels during Conversion of Waste to Biofuel

    Science.gov (United States)

    Cabrini, Marina; Lorenzi, Sergio; Pastore, Tommaso; Pellegrini, Simone; Burattini, Mauro; Miglio, Roberta

    2017-01-01

    The paper deals with the corrosion behavior of stainless steels as candidate materials for biofuel production plants by liquefaction process of the sorted organic fraction of municipal solid waste. Corrosion tests were carried out on AISI 316L and AISI 304L stainless steels at 250 °C in a batch reactor during conversion of raw material to bio-oil (biofuel precursor), by exposing specimens either to water/oil phase or humid gas phase. General corrosion rate was measured by weight loss tests. The susceptibility to stress corrosion cracking was evaluated by means of U-bend specimens and slow stress rate tests at 10−6 or 10−5 s−1 strain rate. After tests, scanning electron microscope analysis was carried out to detect cracks and localized attacks. The results are discussed in relation with exposure conditions. They show very low corrosion rates strictly dependent upon time and temperature. No stress corrosion cracking was observed on U-bend specimens, under constant loading. Small cracks confined in the necking cone of specimens prove that stress corrosion cracking only occurred during slow strain rate tests at stresses exceeding the yield strength. PMID:28772682

  20. The influence of implanted yttrium on the cyclic oxidation behaviour of 304 stainless steel

    Energy Technology Data Exchange (ETDEWEB)

    Riffard, F. [Laboratoire Vellave sur l' Elaboration et l' Etude des Materiaux (LVEEM), CNRS-EA 3864, Universite Blaise Pascal Clermont-Fd II, 8 rue J.B. Fabre, B. P. 219, 43006 Le Puy-en-Velay (France)]. E-mail: riffard@iut.u-clermont1.fr; Buscail, H. [Laboratoire Vellave sur l' Elaboration et l' Etude des Materiaux (LVEEM), CNRS-EA 3864, Universite Blaise Pascal Clermont-Fd II, 8 rue J.B. Fabre, B. P. 219, 43006 Le Puy-en-Velay (France); Caudron, E. [Laboratoire Vellave sur l' Elaboration et l' Etude des Materiaux (LVEEM), CNRS-EA 3864, Universite Blaise Pascal Clermont-Fd II, 8 rue J.B. Fabre, B. P. 219, 43006 Le Puy-en-Velay (France); Cueff, R. [Laboratoire Vellave sur l' Elaboration et l' Etude des Materiaux (LVEEM), CNRS-EA 3864, Universite Blaise Pascal Clermont-Fd II, 8 rue J.B. Fabre, B. P. 219, 43006 Le Puy-en-Velay (France); Issartel, C. [Laboratoire Vellave sur l' Elaboration et l' Etude des Materiaux (LVEEM), CNRS-EA 3864, Universite Blaise Pascal Clermont-Fd II, 8 rue J.B. Fabre, B. P. 219, 43006 Le Puy-en-Velay (France); Perrier, S. [Laboratoire Vellave sur l' Elaboration et l' Etude des Materiaux (LVEEM), CNRS-EA 3864, Universite Blaise Pascal Clermont-Fd II, 8 rue J.B. Fabre, B. P. 219, 43006 Le Puy-en-Velay (France)

    2006-03-15

    High-temperature alloys are frequently used in power plants, gasification systems, petrochemical industry, combustion processes and in aerospace applications. Depending on the application, materials are subjected to corrosive atmospheres and thermal cycling. In the present work, thermal cycling was carried out in order to study the influence of implanted yttrium on the oxide scale adherence on 304 steel specimens oxidised in air at 1273 K. In situ X-ray diffraction indicates that the oxides formed at 1273 K are different on blank specimens compared to implanted specimens. Glancing angle XRD allows to analyse the oxide scale composition after cooling to room temperature. Experimental results show that yttrium implantation at a nominal dose of 10{sup 17} ions cm{sup -2} does not improve significantly the cyclic oxidation behaviour of the austenitic AISI 304 steel. However, it appears that yttrium implantation remarkably enhance the oxidation resistance during isothermal oxidation. It reduces the transient oxidation stage and the parabolic oxidation rate constant by one order of magnitude.

  1. Angle-dependent lubricated tribological properties of stainless steel by femtosecond laser surface texturing

    Science.gov (United States)

    Wang, Zhuo; Li, Yang-Bo; Bai, Feng; Wang, Cheng-Wei; Zhao, Quan-Zhong

    2016-07-01

    Lubricated tribological properties of stainless steel were investigated by femtosecond laser surface texturing. Regular-arranged micro-grooved textures with different spacing and micro-groove inclination angles (between micro-groove path and sliding direction) were produced on AISI 304L steel surfaces by an 800 nm femtosecond laser. The spacing of micro-groove was varied from 25 to 300 μm, and the inclination angles of micro-groove were measured as 90° and 45°. The tribological properties of the smooth and textured surfaces with micro-grooves were investigated by reciprocating ball-on-flat tests against Al2O3 ceramic balls under starved oil lubricated conditions. Results showed that the spacing of micro-grooves significantly affected the tribological property. With the increase of micro-groove spacing, the average friction coefficients and wear rates of textured surfaces initially decreased then increased. The tribological performance also depended on the inclination angles of micro-grooves. Among the investigated patterns, the micro-grooves perpendicular to the sliding direction exhibited the lowest average friction coefficient and wear rate to a certain extent. Femtosecond laser-induced surface texturing may remarkably improve friction and wear properties if the micro-grooves were properly distributed.

  2. Femtosecond laser fabrication of highly hydrophobic stainless steel surface with hierarchical structures fabricated by combining ordered microstructures and LIPSS

    International Nuclear Information System (INIS)

    Martínez-Calderon, M.; Rodríguez, A.; Dias-Ponte, A.; Morant-Miñana, M.C.; Gómez-Aranzadi, M.; Olaizola, S.M.

    2016-01-01

    Highlights: • Femtosecond laser treatment to achieve highly hydrophobic behavior on stainless steel. • Combination of micro-machined patterns with LIPSS into hierarchical structures. • Contact angles as high as 156° with only the femtosecond laser irradiation. - Abstract: In this work we have developed hierarchical structures that consist of micro-patterned surfaces covered by nanostructures with a femtosecond laser. The first part of this work is a study to determine the microscale modifications produced on a stainless steel alloy (AISI304) surface at high pulse energy, different velocities, and number of overscans in order to obtain microstructures with a selected depth of around 10 μm and line widths of 20 μm. The second part of the work is focused on finding the optimal irradiation parameters to obtain the nanostructure pattern. Nanostructures have been defined by means of Laser Induced Periodical Surface Structures (LIPSS) around 250 nm high and a period of 580 nm, which constitute the nanostructure pattern. Finally, dual scale gratings of 50 mm"2 were fabricated with different geometries and their effect on the measured contact angle. Combining the micro-pattern with the LIPSS nano-pattern, highly hydrophobic surfaces have been developed with measured static contact angles higher than 150° on a stainless steel alloy.

  3. Femtosecond laser fabrication of highly hydrophobic stainless steel surface with hierarchical structures fabricated by combining ordered microstructures and LIPSS

    Energy Technology Data Exchange (ETDEWEB)

    Martínez-Calderon, M., E-mail: mmcalderon@ceit.es [CEIT-IK4 & Tecnun (University of Navarra), Paseo Manuel Lardizábal 15, 20018 San Sebastián (Spain); CIC microGUNE, Goiru Kalea 9 Polo Innovación Garaia, 20500 Arrasate-Mondragón (Spain); Rodríguez, A.; Dias-Ponte, A.; Morant-Miñana, M.C.; Gómez-Aranzadi, M.; Olaizola, S.M. [CEIT-IK4 & Tecnun (University of Navarra), Paseo Manuel Lardizábal 15, 20018 San Sebastián (Spain); CIC microGUNE, Goiru Kalea 9 Polo Innovación Garaia, 20500 Arrasate-Mondragón (Spain)

    2016-06-30

    Highlights: • Femtosecond laser treatment to achieve highly hydrophobic behavior on stainless steel. • Combination of micro-machined patterns with LIPSS into hierarchical structures. • Contact angles as high as 156° with only the femtosecond laser irradiation. - Abstract: In this work we have developed hierarchical structures that consist of micro-patterned surfaces covered by nanostructures with a femtosecond laser. The first part of this work is a study to determine the microscale modifications produced on a stainless steel alloy (AISI304) surface at high pulse energy, different velocities, and number of overscans in order to obtain microstructures with a selected depth of around 10 μm and line widths of 20 μm. The second part of the work is focused on finding the optimal irradiation parameters to obtain the nanostructure pattern. Nanostructures have been defined by means of Laser Induced Periodical Surface Structures (LIPSS) around 250 nm high and a period of 580 nm, which constitute the nanostructure pattern. Finally, dual scale gratings of 50 mm{sup 2} were fabricated with different geometries and their effect on the measured contact angle. Combining the micro-pattern with the LIPSS nano-pattern, highly hydrophobic surfaces have been developed with measured static contact angles higher than 150° on a stainless steel alloy.

  4. Photocatalytic activity of ferric oxide/titanium dioxide nanocomposite films on stainless steel fabricated by anodization and ion implantation

    Science.gov (United States)

    Zhan, Wei-ting; Ni, Hong-wei; Chen, Rong-sheng; Yue, Gao; Tai, Jun-kai; Wang, Zi-yang

    2013-08-01

    A simple surface treatment was used to develop photocatalytic activity for stainless steel. AISI 304 stainless steel specimens after anodization were implanted by Ti ions at an extracting voltage of 50 kV with an implantation dose of 3 × 1015 atoms·cm-2 and then annealed in air at 450°C for 2 h. The morphology was observed by scanning electron microscopy. The microstructure was characterized by X-ray diffraction and X-ray photoelectron spectroscopy. The photocatalytic degradation of methylene blue solution was carried out under ultraviolet light. The corrosion resistance of the stainless steel was evaluated in NaCl solution (3.5 wt%) by electrochemical polarization curves. It is found that the Ti ions depth profile resembles a Gaussian distribution in the implanted layer. The nanostructured Fe2O3/TiO2 composite film exhibits a remarkable enhancement in photocatalytic activity referenced to the mechanically polished specimen and anodized specimen. Meanwhile, the annealed Ti-implanted specimen remains good corrosion resistance.

  5. Formability of stainless steel tailored blanks

    DEFF Research Database (Denmark)

    Bagger, Claus; Gong, Hui; Olsen, Flemming Ove

    2004-01-01

    In a number of systematic tests, the formability of tailored blanks consisting of even and different combinations of AISI304 and AISI316 in thickness of 0.8 mm and 1.5 mm have been investigated. In order to analyse the formability of tailored blanks with different sheet thickness, a method based ...

  6. Tema 1: HTTP y aplicaciones web

    OpenAIRE

    Colomina Pardo, Otto; Arques Corrales, Pilar; Montoyo Bojo, Javier

    2011-01-01

    En este tema se introduce el funcionamiento básico del protocolo HTTP, que es el que se usa en las comunicaciones cliente-servidor en aplicaciones web. Además se hace una introducción a las herramientas y plataformas de desarrollo de aplicaciones web.

  7. Sistemas ubiquos: desarrollo y aplicaciones

    OpenAIRE

    Ramón, Hugo Dionisio; Charne, Javier; Di Cicco, Carlos; Riva, Diego Germán de la; Smail, Ana; Osella Massa, Germán Leandro

    2013-01-01

    Se presenta un proyecto de investigación aplicada al cómputo ubiquo (ubicomp), abarcando aspectos que van desde los fundamentos del desarrollo (técnicas de Ingeniería de requerimientos, metodologías de gestión, desarrollo de proyectos, técnicas de planificación, métricas, normas de calidad, redes de sensores y algoritmos inteligentes y procesamiento de señales) hasta la concepción de aplicaciones específicas orientadas a los procesos productivos de la región y el país, procesos de egobierno y...

  8. Anti-adherence potential of Enterococcus durans cells and its cell-free supernatant on plastic and stainless steel against foodborne pathogens.

    Science.gov (United States)

    Amel, Ait Meddour; Farida, Bendali; Djamila, Sadoun

    2015-07-01

    It is demonstrated that numerous bacteria are able to attach to surfaces of equipment used for food handling or processing. In this study, a strain of Enterococcus durans, originally isolated from a milking machine surface, was firstly studied for its biofilm formation potential on plastic and stainless steel supports. The strain was found to be a biofilm producer either at 25, 30 or 37 °C on polystyrene microtitre plates, with a best adherence level observed at 25 °C. En. durans showed a strong adhesion to stainless steel AISI-304. Antibacterial and anti-adherence activities of En. durans were tested against four foodborne pathogens (Escherichia coli ATCC 25922, Staphylococcus aureus ATCC 25923, Pseudomonas aeruginosa ATCC 27853 and Listeria innocua CLIP 74915) which were shown as biofilm producers on both plastic and stainless steel. En. durans cells and cell-free culture supernatant showed a significant (P < 0.05) inhibition potential of the pathogens either on solid media or in broth co-cultures. Characterization of the antibacterial substances indicated their proteinaceous nature which assigned them most probably to bacteriocins group.

  9. Size-separated particle fractions of stainless steel welding fume particles - A multi-analytical characterization focusing on surface oxide speciation and release of hexavalent chromium.

    Science.gov (United States)

    Mei, N; Belleville, L; Cha, Y; Olofsson, U; Odnevall Wallinder, I; Persson, K-A; Hedberg, Y S

    2018-01-15

    Welding fume of stainless steels is potentially health hazardous. The aim of this study was to investigate the manganese (Mn) and chromium (Cr) speciation of welding fume particles and their extent of metal release relevant for an inhalation scenario, as a function of particle size, welding method (manual metal arc welding, metal arc welding using an active shielding gas), different electrodes (solid wires and flux-cored wires) and shielding gases, and base alloy (austenitic AISI 304L and duplex stainless steel LDX2101). Metal release investigations were performed in phosphate buffered saline (PBS), pH 7.3, 37°, 24h. The particles were characterized by means of microscopic, spectroscopic, and electroanalytical methods. Cr was predominantly released from particles of the welding fume when exposed in PBS [3-96% of the total amount of Cr, of which up to 70% as Cr(VI)], followed by Mn, nickel, and iron. Duplex stainless steel welded with a flux-cored wire generated a welding fume that released most Cr(VI). Nano-sized particles released a significantly higher amount of nickel compared with micron-sized particle fractions. The welding fume did not contain any solitary known chromate compounds, but multi-elemental highly oxidized oxide(s) (iron, Cr, and Mn, possibly bismuth and silicon). Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

  10. Application of phosphating techniques to aluminium and carbon steel surfaces using nitro guanidine as oxidizing agent.; Aplicacion de tecnicas de fosfatacion sobre acero al carbon y aluminio, utilizando como agente oxidante la nitroguanidina.

    Energy Technology Data Exchange (ETDEWEB)

    Briseno M, S A

    1995-10-01

    Phosphate coatings are inorganic crystalline deposits laid down uniformly on properly prepared surfaces by a chemical reaction with the treated base metal. The reaction consists in dissolving some surface metal by acid attack and then causing surface neutralization of the phosphate solution with consequent precipitation of the phosphate coating. Phosphate coatings do not provide appreciable corrosion protection in themselves. They are useful mainly as a base for paints, ensuring good adherence of paint to steel and decreasing the tendency for corrosion to under cut the paint film at scratches or other defects. We deposited phosphate on standard carbon steel, employing techniques of cold phosphate (at 40 Centigrade degrees and with a treatment time of 30 minutes) and hot phosphate (at 88 Centigrade degrees and with a treatment time of 15 minutes), where the latter gave the best results. Both methods used phosphate solutions of Zn/Mn and the catalyst Nitro guanidine. Aluminium surfaces of phosphate were used solutions of Cr and as catalyst Sodium bi fluoride. The phosphating on this surface we deposited at temperature of 50 degrees C with a treatment time of 10 minutes. We obtained a new phosphate coating on steel surfaces, these coatings were realized with a phosphate solution manufactured with the precipitates gathered during the hot phosphating on carbon steel. These coatings show excellent physical characteristics of corrosion resistance. The physical testings of the coatings phosphate obtained on carbon steel and aluminium surfaces. These testing were: roughness, thickness, microhardness and adhesion. The best results were showed in carbon steel phosphate with precipitated solutions. Activation analysis with thermic neutrons was used to determine the phosphate coatings composition. Finally, corrosion testings were realized by means of two methods; electrochemical and by weight loss methods (gravimetric). (Abstract Truncated)

  11. Electrochemical behaviour of silica basic hybrid coatings deposited on stainless steel by dipping and EPD

    International Nuclear Information System (INIS)

    Castro, Y.; Duran, A.; Damborenea, J.J.; Conde, A.

    2008-01-01

    The aim of this work is the characterisation of the corrosion behaviour of stainless steel (AISI 304) substrates coated by dipping and electrophoretic deposition (EPD) from a sol-gel basic sol. Particulate silica sols (labelled NaSi) were prepared by basic catalysis from ethyltriethoxysilane (TEOS), methyltriethoxysilane (MTES) and sodium hydroxide. Coatings between 2 and 10 μm were prepared by using concentrated and diluted sols by dipping and EPD process and the corrosion behaviour of the coated substrates were studied through potentiodynamic and impedance spectroscopy measurements (EIS). Potentiodynamic studies of coatings produced by dipping reveal a strong dependence of the protective properties with the concentration of the sol. This behaviour was confirmed by EIS showing that only the coatings obtained from concentrated sol present enough protective properties. On the contrary, EPD coatings prepared from diluted NaSi sol showed an excellent corrosion resistance, maintaining a pure capacitive behaviour for long periods of immersion. EPD deposition is thus proposed as a good alternative method for obtaining thicker and denser coatings with good protective properties from dilute and stable sols

  12. Prevention of weld-decay in austenitic stainless steel by using surface mechanical attrition treatment

    Science.gov (United States)

    Laleh, Majid; Kargar, Farzad; Rouhaghdam, Alireza Sabour

    2012-11-01

    Surface mechanical attrition treatment (SMAT) was applied to the samples of a type AISI 304 stainless steel in order to induce grain refinement as well as formation of twins. Transmission electron microscopy and X-ray diffraction analysis results showed that the average grain size at the surface of the SMATed sample was about 10 nm. The untreated and SMATed samples were then welded using a one-pass gas tungsten arc procedure. The heat-affected zone (HAZ) of the samples was examined by optical microscopy and corrosion tests. Results of the double loop electrochemical potentiokinetic reactivation tests showed that the degree of sensitization in the HAZ for the SMATed sample was very low as compared to that of the untreated one. The pre-SMATed sample was resistant to intergranular corrosion. This is mainly due to the formation of high density of twins which are not prone to carbide precipitation because of their regular and coherent atomic structure and extreme low grain boundary energy as compared with those of other grain boundaries.

  13. Acoustic emission characteristics of stress corrosion cracks in a type 304 stainless steel tube

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, Woong Gi; Bae, Seung Gi; Lee, Bo Young [School of Aerospace and Mechanical Engineering, Korea Aerospace University, Goyang (Korea, Republic of); Kim, Jae Seong [Center for Robot Technology and Manufacturing, Institute for Advanced Engineering, Yongin (Korea, Republic of); Kang, Sung Sik [Dept. of Nuclear Safety Research, Daejeon (Korea, Republic of); Kwag, Nog Won [Ultrasonic Division, RM910, Byucksan Digital Valley II, Seoul (Korea, Republic of)

    2015-06-15

    Acoustic emission (AE) is one of the promising methods for detecting the formation of stress corrosion cracks (SCCs) in laboratory tests. This method has the advantage of online inspection. Some studies have been conducted to investigate the characteristics of AE parameters during SCC propagation. However, it is difficult to classify the distinct features of SCC behavior. Because the previous studies were performed on slow strain rate test or compact tension specimens, it is difficult to make certain correlations between AE signals and actual SCC behavior in real tube-type specimens. In this study, the specimen was a AISI 304 stainless steel tube widely applied in the nuclear industry, and an accelerated test was conducted at high temperature and pressure with a corrosive environmental condition. The study result indicated that intense AE signals were mainly detected in the elastic deformation region, and a good correlation was observed between AE activity and crack growth. By contrast, the behavior of accumulated counts was divided into four regions. According to the waveform analysis, a specific waveform pattern was observed during SCC development. It is suggested that AE can be used to detect and monitor SCC initiation and propagation in actual tubes.

  14. A constitutive equation for hot deformation range of 304 stainless steel considering grain sizes

    International Nuclear Information System (INIS)

    Parsa, M.H.; Ohadi, D.

    2013-01-01

    Highlights: • A hot deformation constitutive equation based on invariant theory is proposed. • Deformation variables are evaluated based on objectivity, entropy principle, etc. • Using hot compression tests, coefficients of equation have been found. • The ability of equation to show the variation of stress with strain is examined. - Abstract: A general constitutive equation based on the framework of invariant theory by consideration of hot deformation key variables and also the properties of the material such as initial grain size is presented in the current work. Soundness of the considered parameters to be used in the developed formula was initially verified based on the important axioms such as objectivity, entropy principle, and thermodynamics stability. To access the prediction ability of the method, the formula was simplified for the simple hot compression test. To evaluate the simplified formula, single-hit hot compression tests were carried out at the temperature range of 900–1100 °C under true strain rate of 0.01–1 s −1 on a AISI 304 stainless steel. The capability of proposed formula for reproducing the variation of flow stress with strain and the strain hardening rate with stress for the resultant flow stress data was examined. The good agreement between model predictions and actual results signified the applicability of this method as a general constitutive equation in hot deformation studies

  15. Chemical sanitizers to control biofilms formed by two Pseudomonas species on stainless steel surface

    Directory of Open Access Journals (Sweden)

    Danila Soares Caixeta

    2012-03-01

    Full Text Available The biofilm formation of Pseudomonas aeruginosa and Pseudomonas fluorescens on AISI 304 stainless steel in the presence of reconstituted skim milk under different temperatures was conducted, and the potential of three chemical sanitizers in removing the mono-species biofilms formed was compared. Pseudomonas aeruginosa cultivated in skim milk at 28 °C presented better growth rate (10.4 log CFU.mL-1 when compared with 3.7 and 4.2 log CFU.mL-1 for P. aeruginosa and P. fluorescens cultivated at 7 °C, respectively. Pseudomonas aeruginosa formed biofilm when cultivated at 28 °C. However, only the adhesion of P. aeruginosa and P. fluorescens was observed when incubated at 7 °C. The sodium dichloroisocyanurate was the most efficient sanitizer in the reduction of the adhered P. aeruginosa cells at 7 and 28 °C and those on the biofilm, respectively. The hydrogen peroxide was more effective in the reduction of adhered cells of P. fluorescens at 7 °C.

  16. Twinning and martensitic transformations in nickel-enriched 304 austenitic steel during tensile and indentation deformations

    Energy Technology Data Exchange (ETDEWEB)

    Gussev, M.N., E-mail: gussevmn@ornl.gov; Busby, J.T.; Byun, T.S.; Parish, C.M.

    2013-12-20

    Twinning and martensitic transformation have been investigated in nickel-enriched AISI 304 stainless steel subjected to tensile and indentation deformation. Using electron backscatter diffraction (EBSD), the morphology of α- and ε-martensite and the effect of grain orientation to load axis on phase and structure transformations were analyzed in detail. It was found that the twinning occurred less frequently under indentation than under tension; also, twinning was not observed in [001] and [101] grains. In tensile tests, the martensite particles preferably formed at the deformation twins, intersections between twins, or at the twin-grain boundary intersections. Conversely, martensite formation in the indentation tests was not closely associated with twinning; instead, the majority of martensite was concentrated in the dense colonies near grain boundaries. Martensitic transformation seemed to be obstructed in the [001] grains in both tensile and indentation test cases. Under a tensile stress of 800 MPa, both α- and ε-martensites were found in the microstructure, but at 1100 MPa only α-martensite presented in the specimen. Under indentation, α- and ε-martensite were observed in the material regardless of the stress level.

  17. DLC coating on stainless steel by pulsed methane discharge in repetitive plasma focus

    International Nuclear Information System (INIS)

    Hassan, M.; Qayyum, A.; Ahmad, S.; Mahmood, S.; Shafiq, M.; Zakaullah, M.; Lee, P.; Rawat, R.S.

    2014-01-01

    Amorphous hydrogenated carbon (a-C:H)/diamond-like carbon (DLC) coatings have been achieved on AISI 304 stainless steel (SS) substrates by employing energetic ions emitted from a repetitive plasma focus operated in CH 4 discharge. The Raman spectroscopy of the coatings exhibits the evolution of a-C:H/DLC coatings with clearly observed D and G peaks centered about 1320–1360 and 1560–1620 cm −1 respectively. The diamond character of the coatings is influenced by the ion flux and repetition rate of the focus device. The repetitive discharge mode of plasma focus has led to the formation of a-C:H/DLC coatings in short duration of time. The coatings transform from a-C to a-C:H depending upon substrate angular position. X-ray diffraction (XRD) analysis confirms the formation of DLC coating owing to stress-induced restructuring in SS. The estimated crystallite size is found to be ∼40–50 nm. Field emission scanning electron micrographs exhibit a layered granular surface morphology of the coatings. The Vickers surface hardness of the DLC coated SS samples has been significantly improved.

  18. DLC coating on stainless steel by pulsed methane discharge in repetitive plasma focus

    Energy Technology Data Exchange (ETDEWEB)

    Hassan, M., E-mail: hassanjh@gmail.com [Department of Physics, Quaid-i-Azam University, 45320 Islamabad (Pakistan); Natural Sciences and Science Education, National Institute of Education, Nanyang Technological University, BLK7, 1 Nanyang Walk, Singapore 637616 (Singapore); Qayyum, A.; Ahmad, S. [National Tokamak Fusion Program, 3329 Islamabad (Pakistan); Mahmood, S. [Natural Sciences and Science Education, National Institute of Education, Nanyang Technological University, BLK7, 1 Nanyang Walk, Singapore 637616 (Singapore); Department of Physics, University of Karachi, 75270 Karachi (Pakistan); Shafiq, M.; Zakaullah, M. [Department of Physics, Quaid-i-Azam University, 45320 Islamabad (Pakistan); Lee, P.; Rawat, R.S. [Natural Sciences and Science Education, National Institute of Education, Nanyang Technological University, BLK7, 1 Nanyang Walk, Singapore 637616 (Singapore)

    2014-06-01

    Amorphous hydrogenated carbon (a-C:H)/diamond-like carbon (DLC) coatings have been achieved on AISI 304 stainless steel (SS) substrates by employing energetic ions emitted from a repetitive plasma focus operated in CH{sub 4} discharge. The Raman spectroscopy of the coatings exhibits the evolution of a-C:H/DLC coatings with clearly observed D and G peaks centered about 1320–1360 and 1560–1620 cm{sup −1} respectively. The diamond character of the coatings is influenced by the ion flux and repetition rate of the focus device. The repetitive discharge mode of plasma focus has led to the formation of a-C:H/DLC coatings in short duration of time. The coatings transform from a-C to a-C:H depending upon substrate angular position. X-ray diffraction (XRD) analysis confirms the formation of DLC coating owing to stress-induced restructuring in SS. The estimated crystallite size is found to be ∼40–50 nm. Field emission scanning electron micrographs exhibit a layered granular surface morphology of the coatings. The Vickers surface hardness of the DLC coated SS samples has been significantly improved.

  19. Analysis of the heat affected zone in CO2 laser cutting of stainless steel

    Directory of Open Access Journals (Sweden)

    Madić Miloš J.

    2012-01-01

    Full Text Available This paper presents an investigation into the effect of the laser cutting parameters on the heat affected zone in CO2 laser cutting of AISI 304 stainless steel. The mathematical model for the heat affected zone was expressed as a function of the laser cutting parameters such as the laser power, cutting speed, assist gas pressure and focus position using the artificial neural network. To obtain experimental database for the artificial neural network training, laser cutting experiment was planned as per Taguchi’s L27 orthogonal array with three levels for each of the cutting parameter. Using the 27 experimental data sets, the artificial neural network was trained with gradient descent with momentum algorithm and the average absolute percentage error was 2.33%. The testing accuracy was then verified with 6 extra experimental data sets and the average predicting error was 6.46%. Statistically assessed as adequate, the artificial neural network model was then used to investigate the effect of the laser cutting parameters on the heat affected zone. To analyze the main and interaction effect of the laser cutting parameters on the heat affected zone, 2-D and 3-D plots were generated. The analysis revealed that the cutting speed had maximum influence on the heat affected zone followed by the laser power, focus position and assist gas pressure. Finally, using the Monte Carlo method the optimal laser cutting parameter values that minimize the heat affected zone were identified.

  20. Modelling and simulations in hot deformation of steels

    International Nuclear Information System (INIS)

    Cabrera, J.M.

    2002-01-01

    Traditionally, hot forming has been employed to provide shape to metals. Nowadays, however, hot working not only produces the desired geometry, but also the mechanical characteristics required. An understanding of the thermomechanical behaviour of metals, and particularly steels, is essential in the simulation and control of the hot forming operations. Moreover, a right prediction of the final properties needs from accurate descriptions of the microstructural features occurring during the shaping step. For this purpose, the determination of constitutive equations describing the stress σ - strain ε relationships at a given strain rate ε, temperature T and initial microstructure, is a useful task. In this sense, computer simulations of hot working processes proportionate a benchmark to engineers and researchers and allow decreasing the cost of developing products and processes. With regard to the prediction of the final microstructure, the simulation of the hot plastic deformation usually gives unsatisfactory results. This is due to the inadequate constitutive equations employed by the conventional and commercial software available to describe the hot flow behaviour. There are scarce models which couple the typical hot working variables (temperature, strain and strain rate) with microstructural characteristics such as grain size. In this review work is presented how the latter limitation can be overcome by using physical-based constitutive equations, some of which have been partially developed by the present authors, where account of the interaction between microstructure and processing variables is taken. Moreover, a practical derivation of the latter expressions on an AISI-304 steel is presented. To conclude, some examples of industrial applications of the latter approach are also presented. Copyright (2002) AD-TECH - International Foundation for the Advancement of Technology Ltd

  1. Welding of stainless steel clad fuel rods for nuclear reactors

    International Nuclear Information System (INIS)

    Neves, Mauricio David Martins das

    1986-01-01

    This work describes the obtainment of austenitic stainless steel clad fuel rods for nuclear reactors. Two aspects have been emphasized: (a) obtainment and qualification of AISI 304 and 304 L stainless steel tubes; b) the circumferential welding of pipe ends to end plugs of the same alloy followed by qualification of the welds. Tubes with special and characteristic dimensions were obtained by set mandrel drawing. Both, seamed and seamless tubes of 304 and 304 L were obtained.The dimensional accuracy, surface roughness, mechanical properties and microstructural characteristics of the tubes were found to be adequate. The differences in the properties of the tubes with and without seams were found to be insignificant. The TIG process of welding was used. The influence of various welding parameters were studied: shielding gas (argon and helium), welding current, tube rotation speed, arc length, electrode position and gas flow. An inert gas welding chamber was developed and constructed with the aim of reducing surface oxidation and the heat affected zone. The welds were evaluated with the aid of destructive tests (burst-test, microhardness profile determination and metallographic analysis) and non destructive tests (visual inspection, dimensional examination, radiography and helium leak detection). As a function of the results obtained, two different welding cycles have been suggested; one for argon and another for helium. The changes in the microstructure caused by welding have been studied in greater detail. The utilization of work hardened tubes, permitted the identification by optical microscopy and microhardness measurements, of the different zones: weld zone; heat affected zone (region of grain growth, region of total and partial recrystallization) and finally, the zone not affected by heat. Some correlations between the welding parameters and metallurgical phenomena such as: solidification, recovery, recrystallization, grain growth and precipitation that occurred

  2. Application of digital image processing to determine the causes of failures in SAE 1018 carbon steel; Aplicacion del procesamiento digital de imagenes para la determinacion de las causas que provocan fallas en el acero al carbono SAE 1018

    Energy Technology Data Exchange (ETDEWEB)

    Bolanos-Rodriguez, E [Escuela Superior de Tizayuca, Universidad Autonoma del Estado de Hidalgo, Tizayuca, Hidalgo (Mexico)]. E-mail: bola7112@yahoo.com.mx; Gonzalez-Islas, J.C. [Universidad Tecnologica de Tulancingo, Tulancingo, Hidalgo (Mexico)]. E-mail: juanc.gonzalez@utec-tgo.edu.mx; Felipe-Riveron, E.M. [Centro de Investigacion en Computacion, Instituto Politecnico Nacional, Mexico, D.F. (Mexico)]. E-mail: edgardo@cic.ipn.mx

    2013-03-15

    The research is focused on determining the causes of failures in the SAE 1018 carbon steel that is used in pipes carrying drinking water. Digital processing of images captured by photomicrographs by scanning electron microscopy coupled with the technique of X-ray microanalysis. The results demonstrate that the low quality of the raw materials and the manufacturing process of steel are the reasons for the occurrence of cracks observed in the material. [Spanish] La investigacion se centra en determinar las causas que provocan fallas en el acero al carbono SAE 1018 que es utilizado en tuberias que transportan agua potable. Se emplea el procesamiento digital de imagenes de las microfotografias captadas por medio de microscopia electronica de barrido, unido a la tecnica de microanalisis de rayos X. Los resultados obtenidos demuestran que la baja calidad de las materias primas y el proceso de manufactura del acero son las razones de la ocurrencia de fisuras observadas en el material.

  3. Localized deformation as a key precursor to initiation of intergranular stress corrosion cracking of austenitic stainless steels employed in nuclear power plants

    International Nuclear Information System (INIS)

    Karlsen, Wade; Diego, Gonzalo; Devrient, Bastian

    2010-01-01

    Cold-work has been associated with the occurrence of intergranular cracking of stainless steels employed in light water reactors. This study examined the deformation behavior of AISI 304, AISI 347 and a higher stacking fault energy model alloy subjected to bulk cold-work and (for 347) surface deformation. Deformation microstructures of the materials were examined and correlated with their particular mechanical response under different conditions of temperature, strain rate and degree of prior cold-work. Select slow-strain rate tensile tests in autoclaves enabled the role of local strain heterogeneity in crack initiation in pressurized water reactor environments to be considered. The high stacking fault energy material exhibited uniform strain hardening, even at sub-zero temperatures, while the commercial stainless steels showed significant heterogeneity in their strain response. Surface treatments introduced local cold-work, which had a clear effect on the surface roughness and hardness, and on near-surface residual stress profiles. Autoclave tests led to transgranular surface cracking for a circumferentially ground surface, and intergranular crack initiation for a polished surface.

  4. Dimensional characteristics of welds performed on AISI 1045 steel by means of the application of high power diode laser; Caracteristicas dimensionales de soldadura formadas sobre el acero AISI 1045 mediante la aplicacion del laser diodo de alta potencia

    Energy Technology Data Exchange (ETDEWEB)

    Sanchez-Castillo, A.; Pou, J.; Lusquinos, F.; Quintero, F.; Soto, R.; Boutinguiza, M.; Saavedra, M.; Perez-Amor, M.

    2004-07-01

    The named High Power diode Laser (HPDL), emits a beam of optical energy generated by diode stimulation and offers the capability of supplying levels of power up to 6 kW. The objective of this research work was to study the main welding variables and their effects on dimensional characteristics of the beads performed by means of application of this novel laser. The results obtained, show that HPDL, is an energy source able to perform welds on AISI 1045 steel plates under conduction mode, without any kind of mechanized preparation, preheating or post-weld treatment and, without filler metal application. (Author) 16 refs.

  5. Dynamic impact response of high-density square honeycombs made of TRIP steel and TRIP matrix composite material

    Directory of Open Access Journals (Sweden)

    Weigelt C.

    2012-08-01

    Full Text Available Two designs of square-celled metallic honeycomb structures fabricated by a modified extrusion technology based on a powder feedstock were investigated. The strength and ductility of these cellular materials are achieved by an austenitic CrNi (AISI 304 steel matrix particle reinforced by an MgO partially-stabilized zirconia building up their cell wall microstructure. Similar to the mechanical behaviour of the bulk materials, the strengthening mechanism and the martensitic phase transformations in the cell walls are affected by the deformation temperature and the nominal strain rate. The microstructure evolution during quasi-static and dynamic impact compression up to high strain rates of 103 1/s influences the buckling and failure behaviour of the honeycomb structures. In contrast to bending-dominated quasi-isotropic networks like open-celled metal foams, axial compressive loading to the honeycomb’s channels causes membrane stretching as well as crushing of the vertical cell node elements and cell walls. The presented honeycomb materials differ geometrically in their cell wall thickness-to-cell size-ratio. Therefore, the failure behaviour is predominantly controlled by global buckling and torsional-flexural buckling, respectively, accompanied by plastic matrix flow and strengthening of the cell wall microstructure.

  6. Construction of cryogenic testing system and tensile deformation behavior of AISI 300 series stainless steels at cryogenic temperatures

    International Nuclear Information System (INIS)

    Lee, H.M.; Nahm, S.H.; Huh, Y.H.; Lee, J.J.; Bahng, G.W.

    1990-01-01

    For practical application of cryogenic engineering, development and characterization of structural materials for use at low temperatures are essential. For these purposes, a system for mechanical testing at liquid helium temperatures was developed and it was shown that the precision and accuracy of the system met the requirements of standards for materials testing machines. Using this system, tensile deformation behavior of AISI 304,316 and 310S austenitic stainless steels at cryogenic temperatures was investigated. Tests were conducted on round, tensile specimens having a 6.25mm diameter at 4,77, and 295 K and loading rate was 0.5mm/min. Serrations were observed in all alloys at 4 K. The stress-displacement curves at 77 and 4 K showed different tendency from those at 298 K. As the testing temperature decreased, ultimate strengths of 304 and 316 were largely increased compared to the increase of yield strengths, but the increase of ultimate strength of 310S was almost the same to that of yield strength. Type 310S had the highest yield strength and the lowest tensile strength at all temperatutes. These tensile characteristics were considered to be strongly affected by austenite stability.(Author)

  7. Corrosion and passivation behavior of various stainless steels in libr solution used in absorption-type refrigeration system

    International Nuclear Information System (INIS)

    Shahid, M.

    2007-01-01

    Various structural materials have been suggested for the refrigeration units to combat high corrosiveness of the absorbent. The corrosion behavior of three grades of austenitic stainless steels, have been investigated in lithium bromide (LiBr) solutions, using electrochemical techniques. Potentiodynamic E- log-i curves, potential-time scans and polarization resistance diagrams obtained by using three-electrode system connected to a computerized Gamry at the rate framework, have been used to analyze their corrosion and passivation behavior in various concentrations of LiBr i.e. commercial LiBr (850 g/J solution containing chromate inhibitor), 400 g/l LiBr and 700 g/J LiBr solutions, at room temperature. Relatively higher corrosion current was observed in SS304 exposed to inhibitor-free electrolyte compared to inhibited commercial solution. Inhibitor proved to be more efficient in case of AISI 304 as it showed significantly higher corrosion rate in un-inhibited solutions. (author)

  8. Atom probe, AFM and STM study on vacuum fired stainless steel

    International Nuclear Information System (INIS)

    Stupnik, A.; Frank, P.; Leisch, M.

    2008-01-01

    Full text: Stainless steel is one of the most commonly used structural materials for vacuum equipment. An efficient method to reduce the outgassing rate from stainless steel is a high temperature bakeout in vacuum (vacuum firing). This procedure reduces significantly the amount of dissolved hydrogen in the bulk. For the outgassing process the recombination rate of hydrogen atoms to the molecules plays the determining role and recombination is strongly related to the surface structure and composition. To get more detailed information about the surface morphology and composition AFM, STM and atom probe studies were carried out. Experiments on AISI 304L stainless steel samples show that the surface reconstructs completely during vacuum firing and large atomically flat terraces bounded by bunched steps and facets are formed. The large flat terraces can be assigned to (111) planes. The bunched steps and facets are corresponding in orientation almost to (110) planes and (100) planes. Surface inspection after vacuum firing by Auger electron spectroscopy (AES) gives reason for a composition change indicated by a reduction of the chromium signal in relation to the iron and nickel signal. Since the information depth of AES covers several atomic layers not only the top atomic layer of the sample surface is probed. For this reason 3D atom probe was used as well suited tool to investigate the segregation behavior of this alloy with the goal to examine the change in local chemical composition due to the high temperature treatment. As a result of vacuum firing the atom probe experiments show a significant enrichment of nickel at the top surface layer. In the second atomic layer chromium enrichment is detected. After vacuum firing the average composition below the second atomic layer shows certain chromium depletion up to 2 nm in depth. The observed changes in surface chemistry influence recombination and desorption probability from the surface and may contribute to the present

  9. Usabilidad en aplicaciones móviles

    OpenAIRE

    Juan Gabriel Enriquez; Sandra Isabel Casas

    2014-01-01

    La usabilidad es considerada uno de los factores más importantes dentro de la calidad de un producto de software. Debido a esto es de interés poder contar con metodologías para medir la usabilidad de las aplicaciones. Los métodos de análisis de usabilidad que actualmente se utilizan, métodos clásicos, fueron desarrollados para aplicaciones de escritorio. Con la aparición, el uso masivo y el crecimiento de los dispositivos móviles, especialmente los Smartphones, la medición de usabilidad en ap...

  10. Aplicaciones farmacéuticas del quitosano

    OpenAIRE

    Montalvo Aique, Pedro Luis; Montalvo Aique, Pedro Luis; Montalvo Aique, Pedro Luis

    2009-01-01

    Entre los temas que se trataran en este informe es sobre el quitosano como una breve reseña histórica donde hablaré sobre las fuentes y métodos de obtención de la quitina, caracterización del quitosano, aplicaciones generales del quitosano, derivados del quitosano de mayor importancia, modificación química del quitosano, quitosanos en diversas formas y las aplicaciones farmacéuticas del quitosano como la liberación de fármacos. La actividad industrial de procesado de los productos de la pe...

  11. Immunological parameters of dental alloy corrosion; A study of gingival inflammation after placement of stainless steel crown

    Directory of Open Access Journals (Sweden)

    Ratna Indriyanti

    2008-11-01

    Full Text Available The dental alloy is widely used in many fields of dentistry as a restoration material, orthodontic, prosthodontic, oral surgery and endodontic treatments. Naturally, most of the metallic materials without exception to stainless steel alloy will experience a process of corrosion in a form of electrochemical reaction to achieve thermodynamic equilibrium. The corrosion process in the oral cavity is due to the reaction of metal with saliva as an oral cavity electrolyte fluid. SSC has preformed restoration material conform with dental anatomy, manufactured from stainless steel alloy which is formable and adaptable to the teeth. Stainless Steel Crown generally made of austenitic stainless steel 18/8 of AISI 304 group contain chrome 18% and Nickel 8%, can be used as a restoration for teeth with excessive caries, crown fracture, email hypoplasia, or restoration after endodontic treatment. The toxic effect of Ni+2 released due to corrosion process may cause an inflammation of the gingiva and periodontal tissue. Laboratorically this condition indicated by the expression of pro-inflammation cytokines as immunological parameters such as IL-6, IL-8, TNF and IL-1β whose main role is to initiate and enhance any inflammation responses. The presence of pro-inflammation cytokines can be detected as soon as 1 hour after placement of SSC by examination of gingival crevicular fluid (GCF by ELISA technique. The magnitude of the toxic effect depends on corrosion rate and ions release which is influenced by metal chemical composition, environment temperature and pH, metal wear due to abrasion and friction, soldering if any, and elongation of the metal. Conclusion: The release of Ni+2 during corrosion process after placement of SSC cause gingival inflammation which is indicated by the change of the immunological parameters.

  12. A conservative damage accumulation method for the prediction of crack nucleation under variable amplitude loading for austenitic stainless steels

    International Nuclear Information System (INIS)

    Taheri, Said; Vincent, Ludovic; Leroux, Jean C.

    2014-01-01

    The application of Miner's rule using a loading issued from a mock-up of a RHR (removal heat system) of PWR plant, made of 304 steel gives a very important non-conservative fatigue lifetime in strain control when strain fatigue curve is used. A large number of test in strain and stress control are performed in different laboratories. Two modeling of literature Smith-Watson-Topper (SWT) and Fatemi-Socie (FS) have been used to simulate these tests. Much better responses than Miner's rule are obtained. However these models need an elastic-plastic constitutive law which is difficult to propose in the presence of high cycle secondary hardening observed in austenitic stainless steels. So a conservative model for fatigue damage accumulation under variable amplitude loading is proposed for austenitic stainless steels (AISI 304, 316) in strain control, which does not need a constitutive law. Linear damage accumulation is used, while, sequence effect is taken into account using the elastic-plastic memory effect through cyclic strain stress curves with pre-hardening. This modeling is based on the fact that for stainless steels, pre-hardening is detrimental for fatigue life in strain control while it is beneficial in stress control. In the case of materials that do not demonstrate load sequence memory the modeling is identical to Miner rule. In the presence of low mean stress, the modeling is approved based on a large number of tests. Moreover the modeling permits to explain the larger detrimental effect of a tension mean stress in strain control tests than in stress control tests. To extend the modeling to higher values of mean stress it is proposed to divide mean stress effect into maximal and 'real' mean stress effects. Extending this work to the case of significant mean stress is ongoing. (authors)

  13. Influence of growth conditions on adhesion of yeast Candida spp. and Pichia spp. to stainless steel surfaces.

    Science.gov (United States)

    Tomičić, Ružica; Raspor, Peter

    2017-08-01

    An understanding of adhesion behavior of Candida and Pichia yeast under different environmental conditions is key to the development of effective preventive measures against biofilm-associated infection. Hence in this study we investigated the impact of growth medium and temperature on Candida and Pichia adherence using stainless steel (AISI 304) discs with different degrees of surface roughness (Ra = 25.20-961.9 nm), material typical for the food processing industry as well as medical devices. The adhesion of the yeast strains to stainless steel surfaces grown in Malt Extract broth (MEB) or YPD broth at three temperatures (7 °C, 37 °C, 43 °C for Candida strains and 7 °C, 27 °C, 32 °C for Pichia strains) was assessed by crystal violet staining. The results showed that the nutrient content of medium significantly influenced the quantity of adhered cells by the tested yeasts. Adhesion of C. albicans and C. glabrata on stainless steel surfaces were significantly higher in MEB, whereas for C. parapsilosis and C. krusei it was YPD broth. In the case with P. pijperi and P. membranifaciens, YPD broth was more effective in promoting adhesion than MEB. On the other hand, our data indicated that temperature is a very important factor which considerably affects the adhesion of these yeast. There was also significant difference in cell adhesion on all types of stainless steel surfaces for all tested yeast. Copyright © 2017 Elsevier Ltd. All rights reserved.

  14. INTERWELD - European project to determine irradiation induced material changes in the heat affected zones of austenitic stainless steel welds that influence the stress corrosion behaviour in high-temperature water

    International Nuclear Information System (INIS)

    Roth, A.; Schaaf, Bob van der; Castano, M.L.; Ohms, C.; Gavillet, D.; Dyck, S. van

    2003-01-01

    PWR and BWR RPV internals have experienced stress corrosion cracking in service. The objective of the INTERWELD project is to determine the radiation induced material changes that promote stress corrosion cracking in the heat affected zone of austenitic stainless steel welds. To achieve this goal, welds in austenitic stainless steel types AISI 304/347 have been fabricated, respectively. Stress-relief annealing was applied optionally. The pre-characterisation of both the as-welded and stress relieved material conditions comprises the examination of the weld residual stresses by the ring-core-technique and neutron diffraction, the degree of sensitisation by EPR, and the stress corrosion behaviour by SSRT testing in high-temperature water. The weldments will be irratiated to 2 neutron fluence levels and a postirradiation examination will determine micromechanical, microchemical and microstructural changes in the materials. In detail, the evolution of the residual stress levels and the stress corrosion behaviour after irradiation will be determined. Neutron diffraction will be utilized for the first time with respect to neutron irradiated material. In this paper, the current state of the project will be described and discussed. (orig.)

  15. A mathematical approach based on finite differences method for analyzing the temperature field in arc welding of stainless steel thin sheets; Desarrollo de un modelo matematico de diferencias finitas para el analisis del campo de temperaturas en la soldadura por arco de chapas finas de acero inoxidable

    Energy Technology Data Exchange (ETDEWEB)

    Martinez-Conesa, E.J.; Estrems, M.; Miguel, V.

    2010-07-01

    This work develops a finite difference method to evaluate the temperature field in the heat affected zone in butt welding applied to AISI 304 stainless steel thin sheet by GTAW process. A computer program has been developed and implemented by Visual Basic for Applications (VBA) in MS-Excel spreadsheet. The results that are obtained using the numerical application foresee the thermal behaviour of arc welding processes. An experimental methodology has been developed to validate the mathematical model that allows to measure the temperature in several points close to the weld bead. The methodology is applied to a stainless steel sheet with a thickness lower than 3 mm, although may be used for other steels and welding processes as MIG/MAG and SMAW. The data which has been obtained from the experimental procedure have been used to validate the results that have been calculated by the finite differences numerical method. The mathematical model adjustment has been carried out taking into account the experimental results. The differences found between the experimental and theoretical approaches are due to the convection and radiation heat losses, which have not been considered in the simulation model.With this simple model, the designer will be able to calculate the thermal cycles that take place in the process as well as to predict the temperature field in the proximity of the weld bead. (Author). 18 refs.

  16. Usabilidad en aplicaciones móviles

    Directory of Open Access Journals (Sweden)

    Juan Gabriel Enriquez

    2014-06-01

    Full Text Available La usabilidad es considerada uno de los factores más importantes dentro de la calidad de un producto de software. Debido a esto es de interés poder contar con metodologías para medir la usabilidad de las aplicaciones. Los métodos de análisis de usabilidad que actualmente se utilizan, métodos clásicos, fueron desarrollados para aplicaciones de escritorio. Con la aparición, el uso masivo y el crecimiento de los dispositivos móviles, especialmente los Smartphones, la medición de usabilidad en aplicaciones móviles se tornó un tema de investigación. Los métodos y métricas actualmente utilizados para medir usabilidad pueden no ser directamente aplicables a este tipo de productos. Los estudios de usabilidad se han efectuado sobre diferentes contextos, recientemente se empezó a considerar la usabilidad en un contexto móvil. Este trabajo examina los métodos y las métricas utilizados para medir usabilidad y pretende analizar que desafíos existen al momento de realizar pruebas de usabilidad en aplicaciones móviles, donde el contexto que cambia continuamente pasa a tener un rol preponderante.

  17. Modeling of the integrity of machining surfaces: application to the case of 15-5 PH stainless steel finish turning

    International Nuclear Information System (INIS)

    Mondelin, A.

    2012-01-01

    During machining, extreme conditions of pressure, temperature and strain appear in the cutting zone. In this thermo-mechanical context, the link between the cutting conditions (cutting speed, lubrication, feed rate, wear, tool coating...) and the machining surface integrity represents a major scientific target. This PhD study is a part of a global project called MIFSU (Modeling of the Integrity and Fatigue resistance of Machining Surfaces) and it focuses on the finish turning of the 15-5PH (a martensitic stainless steel used for parts of helicopter rotor). Firstly, material behavior has been studied in order to provide data for machining simulations. Stress-free dilatometry tests were conducted to obtain the austenitization kinetics of 15-5PH steel for high heating rates (up to 11,000 degrees C/s). Then, parameters of Leblond metallurgical model have been calibrated. In addition, dynamic compression tests (de/dt ranging from 0.01 to 80/s and e ≥ 1) have been performed to calibrate a strain-rate dependent elasto-plasticity model (for high strains). These tests also helped to highlight the dynamic recrystallization phenomena and their influence on the flow stress of the material. Thus, recrystallization model has also been implemented.In parallel, a numerical model for the prediction of machined surface integrity has been constructed. This model is based on a methodology called 'hybrid' (developed during the PhD thesis of Frederic Valiorgue for the AISI 304L steel). The method consists in replacing tool and chip modeling by equivalent loadings (obtained experimentally). A calibration step of these loadings has been carried out using orthogonal cutting and friction tests (with sensitivity studies of machining forces, friction and heat partition coefficients to cutting parameters variations).Finally, numerical simulations predictions of microstructural changes (austenitization and dynamic recrystallization) and residual stresses have been successfully compared with

  18. PROPIEDADES MECÁNICAS DE PELÍCULAS HÍBRIDAS (ORGÁNICO-INORGÁNICO SOBRE ACERO INOXIDABLE 304 Mechanical Properties of Hybrid Films (Organic-Inorganic on Stainless Steel 304

    Directory of Open Access Journals (Sweden)

    Jorge H. Bautista-Ruiz

    2011-12-01

    Full Text Available This article shows the creation of ceramic films of the SiO2-TiO2 Organic Polymer hybrid system from Tetraethyl-Orthosilicate (Si (OC2H54 and Titanium Tetrabutoxide (Ti(OBu4 synthesized through the sol-gel method in several volumetric concentrations of precursors. This hybrid system was deposited on AISI 304 stainless steel substrates through the dip-coating technique. Feasibility for obtaining hybrid and homogeneous coatings on this type of substrate and evaluating the surface properties was studies. For such a purpose, the coating microhardness and adhesion were studies. Additionally, the film surface was characterized through the SEM (Scanning Electron Microscopy. The study concluded that characteristics of films change in function of the volumetric amount of precursors used for creating films.Este trabajo muestra la conformación de películas cerámicas del sistema híbrido SiO2-TiO2-Polímero Orgánico, a partir de tetraetil-ortosilicato (Si (OC2H54, y tetra-butoxido de titanio (Ti(OBu4 y sintetizado por el método sol-gel en diferentes concentraciones volumétricas de los precursores. Este sistema híbrido se depositó sobre sustratos de acero inoxidable AISI 304 mediante la técnica de inmersión (dip-coating. Se estudió la viabilidad de obtener recubrimientos híbridos homogéneos sobre este tipo de sustrato y evaluar las propiedades superficiales. Para tal efecto, se estudió microdureza y adhesión del recubrimiento. Adicionalmente, se caracterizó la superficie de las películas por microscopía electrónica de barrido (MEB. Del estudio se concluye que las características de las películas cambian en función de la cantidad volumétrica de los precursores utilizados en la conformación de las mismas.

  19. QRLabel y Blackbird: 2 aplicaciones accesibles para Android

    OpenAIRE

    Mercade Aguila, Gisela

    2012-01-01

    El objetivo de este proyecto es el de realizar dos aplicaciones para dispositivos móviles con sistema operativo Android. Estas aplicaciones están ideadas para ser usadas por una persona invidente o con deficiencias visuales. El transcurso del desarrollo de cada aplicacion sirve para conocer y experimentar con diferentes herramientas que dispone este sistema operativo, y de este modo estudiar sus ventajas y limitaciones. Se presentan dispositivos y prototipos de dispositivos diseñados exclusiv...

  20. Study on laser welding of austenitic stainless steel by varying incident angle of pulsed laser beam

    Science.gov (United States)

    Kumar, Nikhil; Mukherjee, Manidipto; Bandyopadhyay, Asish

    2017-09-01

    In the present work, AISI 304 stainless steel sheets are laser welded in butt joint configuration using a robotic control 600 W pulsed Nd:YAG laser system. The objective of the work is of twofold. Firstly, the study aims to find out the effect of incident angle on the weld pool geometry, microstructure and tensile property of the welded joints. Secondly, a set of experiments are conducted, according to response surface design, to investigate the effects of process parameters, namely, incident angle of laser beam, laser power and welding speed, on ultimate tensile strength by developing a second order polynomial equation. Study with three different incident angle of laser beam 89.7 deg, 85.5 deg and 83 deg has been presented in this work. It is observed that the weld pool geometry has been significantly altered with the deviation in incident angle. The weld pool shape at the top surface has been altered from semispherical or nearly spherical shape to tear drop shape with decrease in incident angle. Simultaneously, planer, fine columnar dendritic and coarse columnar dendritic structures have been observed at 89.7 deg, 85.5 deg and 83 deg incident angle respectively. Weld metals with 85.5 deg incident angle has higher fraction of carbide and δ-ferrite precipitation in the austenitic matrix compared to other weld conditions. Hence, weld metal of 85.5 deg incident angle achieved higher micro-hardness of ∼280 HV and tensile strength of 579.26 MPa followed by 89.7 deg and 83 deg incident angle welds. Furthermore, the predicted maximum value of ultimate tensile strength of 580.50 MPa has been achieved for 85.95 deg incident angle using the developed equation where other two optimum parameter settings have been obtained as laser power of 455.52 W and welding speed of 4.95 mm/s. This observation has been satisfactorily validated by three confirmatory tests.

  1. Fouling of roughened stainless steel surfaces during convective heat transfer to aqueous solutions

    International Nuclear Information System (INIS)

    Herz, A.; Malayeri, M.R.; Mueller-Steinhagen, H.

    2008-01-01

    The deterioration of heat transfer performance due to fouling is the prime cause for higher energy consumption and inefficiency in many industrial heat exchangers such as those in power plants, refineries, food and dairy industries. Fouling is also a very complex process in which many geometrical, physical and operating parameters are involved with poorly understood interaction. Among them, the surface roughness is an important surface characteristic that would greatly influence crystallisation fouling mechanisms and hence deposition morphology and stickability to the surface. In this work, the effect of the surface roughness of AISI 304 BA stainless steel surfaces on fouling of an aqueous solution with inverse solubility behaviour has been investigated under convective heat transfer. Several experiments have been performed on roughened surfaces ranging from 0.18 to 1.55 μm for different bulk concentrations and heat fluxes. The EDTA titration method was used to measure the concentration of the calcium sulphate salt in order to maintain it at constant value during each fouling run. Experimental results show that the heat transfer coefficient of very rough surfaces (1.55 μm) decreases more rapidly than that of 0.54 μm. Several facts contribute to this behaviour notably (1) increased of primary heterogeneous nucleation rate on the surfaces; (2) reduction of local shear stress in the valleys and (3) reduced removal rate of the crystals from the surfaces where the roughness elements protrude out of the viscous sub-layer. The results also show linear and proportional variation of the fouling rate and heat flux within the range of operating conditions. In addition, the deposition process in terms of fouling rate could only be affected at lower surface contact angles. Such results would particularly be of interest for new surface treatment technologies which aim at altering the surface texture

  2. Dual-species biofilm of Listeria monocytogenes and Escherichia coli on stainless steel surface.

    Science.gov (United States)

    de Grandi, Aline Zago; Pinto, Uelinton Manoel; Destro, Maria Teresa

    2018-04-12

    Listeria monocytogenes is a Gram-positive bacterium commonly associated with foodborne diseases. Due its ability to survive under adverse environmental conditions and to form biofilm, this bacterium is a major concern for the food industry, since it can compromise sanitation procedures and increase the risk of post-processing contamination. Little is known about the interaction between L. monocytogenes and Gram-negative bacteria on biofilm formation. Thus, in order to evaluate this interaction, Escherichia coli and L. monocytogenes were tested for their ability to form biofilms together or in monoculture. We also aimed to evaluate the ability of L. monocytogenes 1/2a and its isogenic mutant strain (ΔprfA ΔsigB) to form biofilm in the presence of E. coli. We assessed the importance of the virulence regulators, PrfA and σ B , in this process since they are involved in many aspects of L. monocytogenes pathogenicity. Biofilm formation was assessed using stainless steel AISI 304 #4 slides immersed into brain heart infusion broth, reconstituted powder milk and E. coli preconditioned medium at 25 °C. Our results indicated that a higher amount of biofilm was formed by the wild type strain of L. monocytogenes than by its isogenic mutant, indicating that prfA and sigB are important for biofilm development, especially maturation under our experimental conditions. The presence of E. coli or its metabolites in preconditioned medium did not influence biofilm formation by L. monocytogenes. Our results confirm the possibility of concomitant biofilm formation by L. monocytogenes and E. coli, two bacteria of major significance in the food industry.

  3. Chemical sanitizers to control biofilms formed by two Pseudomonas species on stainless steel surface Sanificantes químicos no controle de biofilmes formados por duas espécies de Pseudomonas em superfície de aço inoxidável

    Directory of Open Access Journals (Sweden)

    Danila Soares Caixeta

    2012-03-01

    Full Text Available The biofilm formation of Pseudomonas aeruginosa and Pseudomonas fluorescens on AISI 304 stainless steel in the presence of reconstituted skim milk under different temperatures was conducted, and the potential of three chemical sanitizers in removing the mono-species biofilms formed was compared. Pseudomonas aeruginosa cultivated in skim milk at 28 °C presented better growth rate (10.4 log CFU.mL-1 when compared with 3.7 and 4.2 log CFU.mL-1 for P. aeruginosa and P. fluorescens cultivated at 7 °C, respectively. Pseudomonas aeruginosa formed biofilm when cultivated at 28 °C. However, only the adhesion of P. aeruginosa and P. fluorescens was observed when incubated at 7 °C. The sodium dichloroisocyanurate was the most efficient sanitizer in the reduction of the adhered P. aeruginosa cells at 7 and 28 °C and those on the biofilm, respectively. The hydrogen peroxide was more effective in the reduction of adhered cells of P. fluorescens at 7 °C.A capacidade de adesão e formação de biofilme por Pseudomonas aeruginosa e Pseudomonas fluorescens em aço inoxidável AISI 304, na presença de leite desnatado resconstituído sobre diferentes temperaturas foi conduzido e o potencial de três sanificantes químicos na remoção de biofilmes monoespécies foi comparado. Pseudomonas aeruginosa cultivada em leite desnatado a 28 °C apresentou melhor crescimento (10,4 log UFC.mL-1 quando comparado com 3,7 and 4,2 log UFC.mL-1 para P. aeruginosa e P. fluorescens cultivadas a 7 °C, respectivamente. Pseudomonas aeruginosa formou biofilme quando cultivada a 28 °C. Contudo foi observado somente adesão de P. aeruginosa e P. fluorescens quando incubada a 7 °C. O dicloroisocianurato de sódio foi o sanificante mais eficiente na redução de células aderidas e em biofilme de P. aeruginosa a 7 e 28 °C, respectivamente. O peróxido de hidrogênio foi o mais eficiente na redução de células aderidas de P. fluorescens a 7 °C.

  4. Numerical simulation of laser bending of AISI 304 plate with a ...

    African Journals Online (AJOL)

    Keywords: laser bending; process modeling; bending angle; response surface models. ... (Shi et al., 2007) presented numerical simulation of bending for with different shapes of laser ..... Matlab 2011a application code is used to develop and.

  5. Ionic implantation by plasma in titanium and stainless steels used in prosthesis and medical instruments

    International Nuclear Information System (INIS)

    Munoz C, A. E.

    2008-01-01

    A study of a process known as plasma immersion ion implantation (PIII) of nitrogen at low voltages (< 4 kV) into three kind of samples: 1) austenitic stainless AISI 316-L steel plates, 2) ferritic stainless AISI 434 steel-based dentistry drills and 3) commercially pure titanium (CPTi) disks. On the case of CPTi the study was conducted in nitrogen- oxygen calibrated mixtures: 90% N-10% O, 80% N-20% O, 70% N-30% O and in 99.5% pure oxygen and 99.9% pure nitrogen. The PIII process was carried out by using a direct current plasma source controlled both in voltage and current, a negative voltage pulse modulator, a stainless AISI 304 steel vacuum chamber and a rod of the same material, horizontally located in the upper region of the chamber, which plays the role of anode in the plasma discharge. The purpose of the nitriding is forming a relatively thick layer on the surface of the steel specimens in order to enhance their both microhardness and general corrosion performances, desirable in medical applications. This layer contains interstitial nitrogen atoms (∼24% at.) which gives place to a deformed lattice (expanded phase) of the steel. Vickers microhardness and potentiodynamic tests (the latter in agreement to the norm ASTM G-61-89) confirm an increase of microhardness up to three times and a decrease of general corrosion rate in one order of magnitude. The nitriding of de dentistry drills is aimed at inhibiting the pitting corrosion produced by the asepsis process which results in pit nucleations, their propagation and consequent fractures when being under cyclic stress (fatigue). Scanning electron microscope micrographs reveal the risks involved in surpassing the critical treatment simple temperature of 450 C as the PIII process itself induces pitting. On its part, cyclic (ASTM G-61) potentiodynamic tests indicate an excellent pitting corrosion resistance of the samples treated under 450 C. In turn, the treatment of CPTi was meant to develop oxidized and

  6. Seguridad y privacidad en aplicaciones Android

    OpenAIRE

    Piñeiro Ramos, Ismael

    2017-01-01

    Este trabajo explora las vulnerabilidades existentes en los dispositivos móviles tomando como plataforma el sistema operativo Android. Se pretende estudiar en profundidad las posibilidades de inoculación de código de mal comportamiento y el control del hardware de forma remota. La necesidad de estar permanentemente conectado a través del correo electrónico, las herramientas y aplicaciones para redes sociales, la integración de la grabadora de sonido, vídeo y cámara fotográfica en el propio di...

  7. Sistema de realidad aumentada para aplicaciones Android

    OpenAIRE

    Fernández Sánchez, Natalia Mercedes

    2012-01-01

    El objetivo principal de este proyecto es la creación de un sistema de realidad aumentada para el sistema operativo Android con idea de que sea utilizado para la creación de un videojuego, pero que a su vez sea lo suficientemente versátil como para poder utilizarse en otro tipo de aplicaciones. De este objetivo principal podemos obtener los objetivos secundarios: - Conocer las características que ofrecen los teléfonos móviles y como éstas pueden ser aprovechadas para la crea...

  8. A comparison of tensile, fracture and fatigue mechanical behaviour of structural reinforcing bars made with different steels

    Directory of Open Access Journals (Sweden)

    Rodríguez, C.

    2013-09-01

    Full Text Available The use of austenitic stainless steels as rebar is an option increasingly used in reinforced concrete structures exposed to aggressive environments and especially those that have to work in marine environments. The same is true for duplex stainless steel rebars, although nowadays they have a lower use, mainly due to the fact that their inclusion in the reinforced concrete standards was delayed 10 years compared to austenitic stainless steel ones, and consequently their in-service behavior is not as well known. A study of the mechanical properties, including fracture toughness, fatigue behaviour and corrosion resistance in saline alkaline environments of austenitic (AISI 304LN and 316LN and duplex (D2205 stainless steel reinforcing bars was performed in this work. Bars made on a high ductility carbon steel (B500SD that are normally used to reinforce concrete were also characterized and used as a comparison. Stainless steel reinforcing bars show mechanical properties at least similar but usually higher than one of the best carbon steel re-bars (B500SD, along with a significantly higher ductility and, of course, much better corrosion behaviour in saline alkaline environments.El uso de aceros inoxidables austeníticos como armaduras de refuerzo es una opción cada vez más utilizada en estructuras de hormigón armado expuestas a ambientes agresivos y especialmente en las que han de trabajar en ambientes marinos. Lo mismo cabe decir de las armaduras de acero inoxidable dúplex, si bien su uso es menor, debido sobre todo a que su inclusión en la normativa aplicable al armado de hormigón se retrasó 10 años con respecto a los inoxidables austeníticos y, consecuentemente, su comportamiento en servicio es menos conocido. En este trabajo se analiza el comportamiento mecánico, incluyendo fractura y fatiga, así como la resistencia a la corrosión en medios que simulan un hormigón contaminado de cloruros, de armaduras fabricadas tanto con

  9. Application of Box–Behnken design for fabrication of titanium alloy and 304 stainless steel joints with silver interlayer by diffusion bonding

    International Nuclear Information System (INIS)

    Balasubramanian, M.

    2015-01-01

    Highlights: • Diffusion bonding of Ti–6Al–4V to SS304 with silver interlayer was successful. • Hardness and shear strength increased with the increase in the bonding temperature. • Shear strength of 149 MPa and 18% strain to failure were achieved. • Joint efficiency of 80% was obtained for the Ti–6Al–4V and SS304L joints. - Abstract: Direct bonding between titanium (Ti)/titanium alloy(Ti alloy) and stainless steel (SS) promotes the formation of various Fe–Ti and Fe–Cr–Ti intermetallics in the diffusion zone, because the solid solubility of Fe, Cr, Ni and Ti in each other is limited and these intermetallics weaken the mechanical properties of the joint. The present study focuses on the titanium alloy Ti–6Al–4V diffusion bonded to AISI 304 stainless steel with silver foil as an interlayer. The process parameters were chosen appropriately and hence, the bonding is achieved without any defect. Box–Behnken design is used to decide the optimum number of experiments required to do the investigation. Microhardness measurements and the lap shear test were carried out to determine the hardness and strength of the joints respectively. The results show that atomic diffusion and migration between Ti and Fe or C are effectively prevented by adding pure Ag as the interlayer metal. The results from mechanical testing showed that shear strength values have a direct relationship with bonding time. The maximum lap shear strength of 149 MPa and 18% strain to failure was observed for joints obtained with bonding time of 60 min. However, effective bonding was not possible at 850 °C due to incomplete coalescence of mating surfaces

  10. Laser shock peening without coating induced residual stress distribution, wettability characteristics and enhanced pitting corrosion resistance of austenitic stainless steel

    Science.gov (United States)

    Prabhakaran, S.; Kulkarni, Aniket; Vasanth, G.; Kalainathan, S.; Shukla, Pratik; Vasudevan, Vijay K.

    2018-01-01

    Low energy laser shock peening without coating (LSPwC) was conducted on AISI 304 austenitic stainless steel specimens with varying pulse densities or overlapping. Highest magnitude of compressive residual stress (CRS) was achieved for an optimized pulse density of 2500 pulses/cm2 (75% overlapping). The 2-D and 3-D topographical analysis were indicative of the fact that controlled roughening of the surface was achieved after the LSPwC process. After the LSPwC process, the hydrophilic unpeened surface was converted into the hydrophobic surface, thus decreasing the wettability characteristics of the surface. The X-ray diffraction (XRD) results reveal that there is a beginning of the martensite transformation and the rise in the intensity value of the peaks after LSPwC indicates the presence of compressive residual stresses induced in the specimen. The optical microscope and high-resolution transmission electron microscope results provided evidence of grain refinement and deformation induced refinement features such as multidirectional mechanical twinning, dislocations lines, micro shear cells and stacking faults in the near and sub-surface areas. The average hardness value of the LSPwC specimens was found to be increased by 28% more than the untreated specimen. The potentiodynamic polarization revealed that there was a considerable amount of increase in the pitting corrosion resistance after the LSPwC process, thus, supporting to extend the fatigue life of the specimen. The electrochemical impedance spectroscopic (EIS) analysis depicts that the LSPwC process supports the formation of the strong passivation layer in 3.5% NaCl solution.

  11. La estructura del fullereno C60 y sus aplicaciones

    OpenAIRE

    Vasilievna Kharissova, Oxana; Ortiz Méndez, Ubaldo

    2002-01-01

    Se revisan los datos reportados de una nueva clase de materiales basados en los fullerenos. Se explica la estructura del fullereno C60 y sus compuestos con metales alcalinos, sus propiedades y aplicaciones. Se señala que estos compuestos tienen propiedades de superconducción comparable con la de los tradicionales cupratos. Se indica que esta modificación del carbono puede formar nanotubos que tienen varias aplicaciones prácticas debido a sus propiedades.

  12. Aplicaciones industriales de la tecnología nuclear

    OpenAIRE

    Vargas, Celso

    2013-01-01

    Las aplicaciones industriales de la tecnología nuclear son muydiversas a nivel mundial. En Costa Rica se ha comenzado a introducir este tipo de tecnología para evaluar y mejorar diferentes procesos industriales. Estas aplicaciones se clasifican en dos o en tres categorías, según el criterio utilizado. Están los sistemasde control nucleónico, el perfilaje gamma y los radiotrazadores.

  13. Receptor GNSS multiantena para aplicaciones aeroespaciales

    OpenAIRE

    Cogo, Jorge; López La Valle, Ramón G.; Puga, Gerardo L.; Smidt, Javier A.; Díaz, Juan G.; García, Javier Gonzalo; Roncagliolo, Pedro Agustín; Muravchik, Carlos Horacio

    2013-01-01

    La determinación de la posición y velocidad del vehículo es una de las tareas críticas en las aplicaciones aeroespaciales como es el caso de aviones, satélites o cohetes. En los últimos años esta tarea se ha visto favorecida por el despliegue de los Sistemas de Navegación Global por Satélite (GNSS). Estos sistemas, utilizando como base una constelación de satélites que envían señales a la superficie terrestre, permiten que un usuario que cuente con un receptor adecuado pueda obtener esta info...

  14. Influence of damage rate on physical and mechanical properties and swelling of 18Cr-9Ni austenitic steel in the range of 3.10-9 to 4.10-8 dpa/sec

    International Nuclear Information System (INIS)

    Shcherbakov, E.N.; Kozlov, A.V.; Yagovitin, R.I.; Evseev, M.V.; Kinev, E.A.; Isobe, Y.; Sagisaka, M.; Okita, T.; Sekimura, N.; Garner, F.

    2007-01-01

    Full text of publication follows: Whereas most data on radiation-induced changes in mechanical properties or dimensional stability needed for fusion - relevant dpa levels and dpa rates are generated at relatively high neutron flux in fast reactors, many fusion and fission components will operate at much lower dpa rates. Much less data are available from long-lived structural components operating at very low flux levels. In addition most published data were generated from relatively thin specimens (∼1-2 mm or less), while some actual fusion structural components can be on the order of 1-2 cm thick. In this study we have examined a 9 cm diameter pipe constructed from Fe-18Cr-9Ni steel analogous to AISI 304 that stayed outside the core of BN-600 for 22 years. The walls of the pipe were 2 cm thick and experienced temperatures in the range 370-375 deg. C. The walls were sectioned into 5 slices at a number of positions to yield doses in the range 1.5 to 22 dpa at 3 x 10 -9 to 4 x 10 -8 dpa/s. Changes in elastic moduli were studied using an ultrasonic technique and changes in electrical resistivity and mechanical properties of the 18Cr9Ni austenitic steel was examined. Swelling was measured both by immersion density and electron microscopy, reaching a maximum of ∼3 %. Swelling appears to be accelerated somewhat at these lower dpa rates as observed in other recent studies. Tensile properties were also measured. Radiation-induced changes of electrical resistivity, Young's and shear moduli were observed but did not agree fully with predictions based on voids alone. Strong contributions from second phase precipitates were found to be contributing to changes in both physical and mechanical properties. (authors)

  15. SCC of cold-worked austenitic stainless steels exposed to PWR primary water conditions: susceptibility to initiation

    International Nuclear Information System (INIS)

    Herms, E.; Raquet, O.; Sejourne, L.; Vaillant, F.

    2009-01-01

    Heavily cold-worked austenitic stainless steels (AISI 304L and 316L types) could be significantly susceptible to Stress Corrosion Cracking (SCC) when exposed to PWR nominal primary water conditions even in absence of any pollutants. Susceptibility to SCC was shown to be related with some conditions such as initial hardness, procedure of cold-work or dynamic straining. A dedicated program devoted to better understand the initiation stage on CW austenitic stainless steels in PWR water is presented. Initiation is studied thanks to SCC test conditions leading to an intergranular cracking propagation mode on a CW austenitic stainless steel which is the mode generally reported after field experience. SCC tests are carried out in typical primary water conditions (composition 1000 ppm B and 2 ppm Li) and for temperature in the range 290 - 340 C. Material selected is 316L cold-worked essentially by rolling (reduction in thickness of 40%). Initiation tests are carried out under various stress levels with the aim to investigate the evolution of the initiation period versus the value of applied stress. SCC tests are performed on cylindrical notched specimens in order to increase the applied stress and allow accelerated testing without modify the exposure conditions to strictly nominal hydrogenated PWR water. Respective influences of cyclic/dynamic conditions on SCC initiation are presented and discussed. Dedicated interrupted tests help to investigate the behaviour of the crack initiation process. These SCC tests have shown that crack initiation could be obtained after a very short time under dynamic loading conditions on heavily pre-strained austenitic stainless steels. Actual results show that the most limiting stage of the cracking process on CW 316L seems to be the transition from slow transgranular propagation of surface initiated cracks to intergranular fast propagation through the thickness of the sample. The duration of this stage during crack initiation tests is

  16. INTEGRACIÓN DE APLICACIONES EN LAS EMPRESAS

    Directory of Open Access Journals (Sweden)

    Odalys Jordán Enríquez

    2006-04-01

    Full Text Available

     

    La integración de aplicaciones es el proceso de lograr que aplicaciones independientes trabajen juntas para producir un conjunto unificado de funcionalidades. Los desarrolladores de aplicaciones siempre tienen que lograr comunicar disímiles arquitecturas de información y hacer interoperar diferentes tecnologías, incluyendo sistemas operativos, lenguajes de programación, plataformas de aplicaciones y sistemas gestores de bases de datos. Las soluciones de integración pueden tener muchas variantes y estar presentes a varios niveles. En este trabajo se abordan los desafíos de la integración, criterios a considerar al realizar la integración y cuatro tipos de integración de aplicaciones. En estos tipos de soluciones presentadas, los patrones de la solución son el enfoque, no las implementaciones.

  17. Material Characterization of Fatigue Specimens made from Meta-stable Austenitic Stainless Steel

    Energy Technology Data Exchange (ETDEWEB)

    Niffenegger, M.; Grosse, M.; Kalkhof, D.; Leber, H. [Paul Scherrer Institut Villigen (Switzerland); Vincent, A.; Pasco, L.; Morin, M. [Insa de Lyon (France)

    2003-07-01

    The main objective of the EU-project CRETE (Contract No.: FIS5-1999-00280) was to assess the capability and the reliability of innovative NDT-inspection techniques for the detection of material degradation, induced by thermal fatigue and neutron irradiation, of metastable austenitic and ferritic low-alloy steel. Several project partners tested aged or irradiated samples, using various techniques (acoustic, magnetic and thermoelectric). However, these indirect methods require a careful interpretation of the measured signal in terms of micro-structural evolutions due to ageing of the material. Therefore the material had to be characterized in its undamaged, as well as in its damaged state. The present report summarises only the material characterization of the fatigue specimens. It is issued simultaneously as an PSI Bericht and the CRETE work package 3 (WP3) report. Each partner according to their own specifications purchased three materials under investigation, namely AISI 347, AISI 321 and AISI 304L. After sending the material to PSI, all fatigue specimens were manufactured by the same Swiss company. Each partner was responsible for his fatigue tests which are documented in the report WP1, written by FANP. In order to characterize the material in its unfatigued as well as in its fatigued state and to consider microstructural changes related to fatigue damage the methods listed below were employed either by PSI or by INSA de Lyon: (1) Inductive Coupled Plasma Emission Photometry (ICP-OES) was applied to determine the chemical composition, (2) Scanning electron microscopy (SEM) for observing cracks, slip bands between grain and twin boundaries, - Ferromaster for measuring the magnetic permeability, (3) Physical Properties Measuring System (PPMS) for measuring magnetization characteristics, (4) Neutron- and advanced X-ray diffraction methods for the quantitative determination of martensite, - Transmission electron microscopy (TEM) for the observation of crystalline

  18. Dissolution and oxidation behaviour of various austenitic steels and Ni rich alloys in lead-bismuth eutectic at 520 °C

    Energy Technology Data Exchange (ETDEWEB)

    Roy, Marion, E-mail: marion.roy@cea.fr [CEA, DEN, DPC, SCCME, Laboratoire d’Etude de la Corrosion Non Aqueuse, F-91191 Gif-sur-Yvette (France); Martinelli, Laure, E-mail: laure.martinelli@cea.fr [CEA, DEN, DPC, SCCME, Laboratoire d’Etude de la Corrosion Non Aqueuse, F-91191 Gif-sur-Yvette (France); Ginestar, Kevin, E-mail: kevin.ginestar@cea.fr [CEA, DEN, DPC, SCCME, Laboratoire d’Etude de la Corrosion Non Aqueuse, F-91191 Gif-sur-Yvette (France); Favergeon, Jérôme, E-mail: jerome.favergeon@utc.fr [Laboratoire Roberval, UMR 7337, Université de Technologie de Compiègne, Centre de Recherche de Royallieu, CS 60319, 60203 Compiègne Cedex (France); Moulin, Gérard [Laboratoire Roberval, UMR 7337, Université de Technologie de Compiègne, Centre de Recherche de Royallieu, CS 60319, 60203 Compiègne Cedex (France)

    2016-01-15

    Ten austenitic steels and Ni rich alloys were tested in static lead-bismuth eutectic (LBE) at 520 °C in order to obtain a selection of austenitic steels having promising corrosion behaviour in LBE. A test of 1850 h was carried out with a dissolved oxygen concentration between 10{sup −9} and 5 10{sup −4} g kg{sup −1}. The combination of thermodynamic of the studied system and literature results leads to the determination of an expression of the dissolved oxygen content in LBE as a function of temperature: RT(K)ln[O](wt%) = −57584/T(K) −55.876T(K) + 254546 (R is the gas constant in J mol{sup −1} K{sup −1}). This relation can be considered as a threshold of oxygen content above which only oxidation is observed on the AISI 316L and AISI 304L austenitic alloys in static LBE between 400 °C and 600 °C. The oxygen content during the test leads to both dissolution and oxidation of the samples during the first 190 h and leads to pure oxidation for the rest of the test. Results of mixed oxidation and dissolution test showed that only four types of corrosion behaviour were observed: usual austenitic steels and Ni rich alloys behaviour including the reference alloy 17Cr-12Ni-2.5Mo (AISI 316LN), the 20Cr-31Ni alloy one, the Si containing alloy one and the Al containing alloy one. According to the proposed criteria of oxidation and dissolution kinetics, silicon rich alloys and aluminum rich alloy presented a promising corrosion behaviour. - Highlights: • 10 austenitic steels and Ni rich alloys were tested in LBE at 520 °C with dissolved oxygen content between 10{sup -9} and 5 10{sup -4} wt%. • It is shown that only thermodynamics cannot explain the Ni rich alloys corrosion behaviour in LBE. • The role of oxygen on corrosion behaviour in LBE was highlighted. • An equilibrium line was defined above which only oxidation has occurred on 316L: RTln[O](wt%) = -57584/T(K)-55.876T(K)+254546. • 18Cr-15Ni-3.7Si, 21Cr-11Ni-1.6Si and 14Cr-25Ni-3.5Al

  19. Aplicaciones multimedia para rehabilitación cognitiva

    OpenAIRE

    Ortega Bastida, Javier

    2016-01-01

    Diseño de aplicaciones multimedia que posibilitan la rehabilitación de los pacientes a través de aplicaciones de realidad virtual e interfaces 3D: manipulación virtual de entidades, texto predictivo y dibujo guiado sobre entrono integrado para sistema multisensor para rehabilitación e interacción de personas con discapacidad, tanto motora, como cognitiva. El sistema permite la realización de terapias utilizando distintos modos de interacción hombre-máquina, posibilitando múltiples modos de in...

  20. Uso y aplicaciones de drones en minería

    OpenAIRE

    Sánchez García, Manuel

    2017-01-01

    Los drones son una tecnología actual y en pleno desarrollo con múltiples aplicaciones pero ¿conocemos todas las posibilidades que nos ofrecen dentro de la minería? Este proyecto pretende dar respuesta a esta pregunta y poner de manifiesto todas las aplicaciones potenciales. Los drones, también conocidos como VANT (Vehículo Aéreo No Tripulado) o UAV (Unmaned Aerial Vehicle), son aeronaves que vuelan sin tripulación, reutilizables, capaz de mantener de manera autónoma un vuelo controlado y ...

  1. Aplicaciones sobre plataformas de redes neuronales en tiempo real

    OpenAIRE

    Tosini, Marcelo Alejandro; Acosta, Nelson

    2003-01-01

    El presente trabajo pretende el diseño de una metodología para la construcción de aplicaciones basadas en redes neuronales sobre una plataforma Muren. Las aplicaciones se restringen a sistemas de control y reconocimiento de patrones por imágenes. Se describe la arquitectura del sistema de desarrollo Muren, basado en 2 procesadores ZISC de 78 neuronas cada uno, una FPGA Spartan II, bancos de memoria y lógica adicional de comunicación.

  2. Antibacterial silver nanocluster/silica composite coatings on stainless steel

    Energy Technology Data Exchange (ETDEWEB)

    Ferraris, M.; Perero, S. [Politecnico di Torino, Department of Applied Science and Technology, Torino, C.so Duca degli Abruzzi 24, I-10129 (Italy); Ferraris, S., E-mail: sara.ferraris@polito.it [Politecnico di Torino, Department of Applied Science and Technology, Torino, C.so Duca degli Abruzzi 24, I-10129 (Italy); Miola, M.; Vernè, E. [Politecnico di Torino, Department of Applied Science and Technology, Torino, C.so Duca degli Abruzzi 24, I-10129 (Italy); Skoglund, S. [KTH Royal Institute of Technology, Div. Surface and Corrosion Science, Dr. Kristinas v. 51, SE-100 44 (Sweden); Blomberg, E. [KTH Royal Institute of Technology, Div. Surface and Corrosion Science, Dr. Kristinas v. 51, SE-100 44 (Sweden); SP Technical Research Institute of Sweden, Chemistry, Materials and Surfaces, P.O. Box 5607, SE-114 86 Stockholm (Sweden); Odnevall Wallinder, I. [KTH Royal Institute of Technology, Div. Surface and Corrosion Science, Dr. Kristinas v. 51, SE-100 44 (Sweden)

    2017-02-28

    Highlights: • A silver nanocluster-silica composite coating sputter-deposited onto stainless steel. • Good adhesion and resistance upon cleaning with NaOH, H{sub 2}SO{sub 4} and detergents. • Low release of silver ions and no release as silver nanoparticles. • Good antibacterial activity against S. aureus even after heating to 450 °C. • Good antibacterial activity shown during cheese production. - Abstract: A coating made of silver nanocluster/silica composites has been deposited, via a radio frequency (RF) co-sputtering technique, for the first time onto stainless steel (AISI 304L) with the aim to improve its antibacterial properties. Different thermal treatments after coating deposition have been applied in order to optimize the coating adhesion, cohesion and its antibacterial properties. Its applicability has been investigated at realistic conditions in a cheese production plant. The physico-chemical characteristics of the coatings have been analyzed by means of different bulk and surface analytical techniques. Field emission scanning electron microscopy (FESEM), X-ray Photoelectron Spectroscopy (XPS), contact angle measurements and atomic force microscopy (AFM) were employed to assess coating morphology, composition, surface roughness, wetting properties, size and local distribution of the nanoparticles within the coating. Tape tests were used to determine the adhesion/cohesion properties of the coating. The amount and time-dependence of released silver in solutions of acetic acid, artificial water, artificial tap water and artificial milk were determined by means of Atomic Absorption Spectroscopy (AAS). The antibacterial effect of the coating was evaluated at different experimental conditions using a standard bacterial strain of Staphylococcus aureus in compliance with National Committee for Clinical Laboratory Standards (NCCLS) and AATCC 147 standards. The Ahearn test was performed to measure the adhesion of bacteria to the coated stainless steel

  3. Antibacterial silver nanocluster/silica composite coatings on stainless steel

    International Nuclear Information System (INIS)

    Ferraris, M.; Perero, S.; Ferraris, S.; Miola, M.; Vernè, E.; Skoglund, S.; Blomberg, E.; Odnevall Wallinder, I.

    2017-01-01

    Highlights: • A silver nanocluster-silica composite coating sputter-deposited onto stainless steel. • Good adhesion and resistance upon cleaning with NaOH, H_2SO_4 and detergents. • Low release of silver ions and no release as silver nanoparticles. • Good antibacterial activity against S. aureus even after heating to 450 °C. • Good antibacterial activity shown during cheese production. - Abstract: A coating made of silver nanocluster/silica composites has been deposited, via a radio frequency (RF) co-sputtering technique, for the first time onto stainless steel (AISI 304L) with the aim to improve its antibacterial properties. Different thermal treatments after coating deposition have been applied in order to optimize the coating adhesion, cohesion and its antibacterial properties. Its applicability has been investigated at realistic conditions in a cheese production plant. The physico-chemical characteristics of the coatings have been analyzed by means of different bulk and surface analytical techniques. Field emission scanning electron microscopy (FESEM), X-ray Photoelectron Spectroscopy (XPS), contact angle measurements and atomic force microscopy (AFM) were employed to assess coating morphology, composition, surface roughness, wetting properties, size and local distribution of the nanoparticles within the coating. Tape tests were used to determine the adhesion/cohesion properties of the coating. The amount and time-dependence of released silver in solutions of acetic acid, artificial water, artificial tap water and artificial milk were determined by means of Atomic Absorption Spectroscopy (AAS). The antibacterial effect of the coating was evaluated at different experimental conditions using a standard bacterial strain of Staphylococcus aureus in compliance with National Committee for Clinical Laboratory Standards (NCCLS) and AATCC 147 standards. The Ahearn test was performed to measure the adhesion of bacteria to the coated stainless steel surface

  4. Application of a TiAIN coating for the increase wear resistance of a passage floodgate manufactured in steel T9; Aplicacion de un recubrimiento de TiAIN para el incremento de la resistencia al desgaste de una compuerta de paso fabricada en acero T9

    Energy Technology Data Exchange (ETDEWEB)

    Montes de Oca, J.; Gonzalez, H. J. [Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada, IPN, Unidad Altamira, Km. 14.5 Carretera Tampico-Puerto industrial Altamira, 89600 Altamira, Tamaulipas (Mexico); Solis, E. [Hy-Teck Fluid Power, Blvd. A. Lopez Mateos No. 310, Col. Nuevo Aeropuerto, 89337 Tampico, Tamaulipas (Mexico); Moreno, J. [Departamento de Ingenieria Metalurgica, Escuela Superior de Ingenieria Quimica e Industrias Extractivas, IPN, UPALM Unidad Zacatenco, 07730 Mexico D. F. (Mexico); Munoz S, J. [Centro de Investigacion y de Estudios Avanzados, Unidad Queretaro, Libramiento Norponiente No. 2000, Fracc. Real de Juriquilla, 76230 Santiago de Queretaro, Queretaro (Mexico)], e-mail: jmontedeocav@ipn.mx

    2009-07-01

    The present work reports a study to increase wear resistance of a ball passage floodgate (steel type T9) trough the application of a thick film (coating). This study have included a material and process selection, synthesis of the coating on steel plates as substrates and spherical device, assembling of the coated floodgate on the ball valves, and finally an evaluation of the valves in the process of a thermoelectric power station. Taking into account the different requirements, a TiAIN coating prepared by cathodic arc evaporation was finally retained. The crystal structure, morphology and chemical composition of the coating were evaluated by x-ray diffraction (XRD) and scanning electron microscopy equipped with an energy dispersive spectrometer (SEM-EDS). Finally, mechanical properties such as hardness and Young modulus were determined by nano indentation. (Author)

  5. Ionic implantation by plasma in titanium and stainless steels used in prosthesis and medical instruments; Implantacion ionica por plasma en titanio y aceros inoxidables usados en protesis e instrumental medico

    Energy Technology Data Exchange (ETDEWEB)

    Munoz C, A. E. [ININ, 52750 La Marquesa, Estado de Mexico (Mexico)

    2008-07-01

    A study of a process known as plasma immersion ion implantation (PIII) of nitrogen at low voltages (< 4 kV) into three kind of samples: 1) austenitic stainless AISI 316-L steel plates, 2) ferritic stainless AISI 434 steel-based dentistry drills and 3) commercially pure titanium (CPTi) disks. On the case of CPTi the study was conducted in nitrogen- oxygen calibrated mixtures: 90% N-10% O, 80% N-20% O, 70% N-30% O and in 99.5% pure oxygen and 99.9% pure nitrogen. The PIII process was carried out by using a direct current plasma source controlled both in voltage and current, a negative voltage pulse modulator, a stainless AISI 304 steel vacuum chamber and a rod of the same material, horizontally located in the upper region of the chamber, which plays the role of anode in the plasma discharge. The purpose of the nitriding is forming a relatively thick layer on the surface of the steel specimens in order to enhance their both microhardness and general corrosion performances, desirable in medical applications. This layer contains interstitial nitrogen atoms ({approx}24% at.) which gives place to a deformed lattice (expanded phase) of the steel. Vickers microhardness and potentiodynamic tests (the latter in agreement to the norm ASTM G-61-89) confirm an increase of microhardness up to three times and a decrease of general corrosion rate in one order of magnitude. The nitriding of de dentistry drills is aimed at inhibiting the pitting corrosion produced by the asepsis process which results in pit nucleations, their propagation and consequent fractures when being under cyclic stress (fatigue). Scanning electron microscope micrographs reveal the risks involved in surpassing the critical treatment simple temperature of 450 C as the PIII process itself induces pitting. On its part, cyclic (ASTM G-61) potentiodynamic tests indicate an excellent pitting corrosion resistance of the samples treated under 450 C. In turn, the treatment of CPTi was meant to develop oxidized and

  6. Corrosion Aggressivenes of Soil Related to the Activity of

    African Journals Online (AJOL)

    naoc

    resulting from attack on the metal by sulphate-reducing bacteria in the soils. KEY WORDS: ... analysis of corrosion products formed on the surfaces of X60 steel coupons buried in ..... publication on the control of biofilm growth in drinking water distribution ... passive film formed on austentic stainless steel AISI. 304, Corrosion ...

  7. Corrosion Properties of Sintered and Wrought Stainless Seel

    DEFF Research Database (Denmark)

    Mathiesen, Troels; Maahn, Ernst Emanuel

    1997-01-01

    The corrosion properties of a range of stainless steels produced by powder metallurgy (PM) are compared with wrought AISI304 and AISI316 Steel. Characterisation of the passivation properties in 0.5M H2SO4 and pittingresistance in 0.3% chloride solution by polarisation show properties...

  8. Aceros aluminotérmicos. Nuevas aplicaciones

    Directory of Open Access Journals (Sweden)

    Duart Blay, J. M.

    2004-02-01

    Full Text Available The metallothermy is a process based on physical ' chemistry possibility of metallic oxides reduction (Fe, Cr, Mn, Cu for oxygen strong affinity metals, like Al, Mg and Ti. The reaction is highly exothermic giving place to a metallic phase and slag separation by refining and reduction process simultaneously. The technological developed patent initially by Thermit - and improved for other Companies - works well by more than 50 years; today it is employed almost exclusively for obtaining steels and coppers for complex welded joints unions. Particular application or interest presents in the Railways technology for building continuous tracks, practically implanted in all the word and in welding copper cable rope - steel rail employed for traffic signals control. This work displays the fundamental thermodynamic principles of the aluminothermics of iron and their application to the complex weld of crossrail, dilation joints and bypass in Railways, that combine Hadfield steels, stainless steels and pearlitic steels of different mechanical properties. The unions should be compact, with strength and hardness in the levels that are cited in the work, according to requirements demanded by high speed (350 km/ h. lines, now in construction in Spain, but they result of general use to whatever class of less demanding lines and to mining railroads.

    La metalotermia es un proceso físicoquímico basado en la posibilidad de reducción de óxidos metálicos (hierro, cromo, manganeso, cobre por metales altamente afines por el oxígeno, como son aluminio, magnesio y titanio. La reacción es altamente exotérmica dando lugar a un caldo metálico separado de su escoria, por un proceso de reducción y afino combinados. La patente tecnológica, desarrollada inicialmente por Thermit y perfeccionada por otras Compañías, lleva en vigor más de 50 años; se aplica hoy, casi exclusivamente, a la obtención de aceros y cobres para uniones soldadas complejas

  9. Development of a Novel Approach for Fatigue Life Prediction of Structural Materials

    Science.gov (United States)

    2008-12-01

    Mughrabi, H., 1989, "Plasticity-Induced Martensitic Transformation of AISI 304L Stainless Steel ," Mat Sci Eng A114, pp. LI 1-LI 6. [26] Krupp, U...four structural materials: aluminum 7075T651 alloy, stainless steel AL6-XN, stainless steel 304L, and Aerospace Steel 4340. It was confirmed that...four structural materials: aluminum 7075T651 alloy, stainless steel AL6-XN, stainless steel 304L, and Aerospace Steel 4340. Fatigue and cyclic

  10. Influência da velocidade de circulação do leite na adesão de Pseudomonas aeruginosa sobre aço inoxidável The speed of milk circulation influences the adhesion of Pseudomonas aeruginosa on stainless steel

    Directory of Open Access Journals (Sweden)

    Hamilton Mendes de Figueiredo

    2009-09-01

    Full Text Available A influência da velocidade de circulação do leite na adesão bacteriana de Pseudomonas aeruginosa foi avaliada em teste de uso simulado por meio de um modelo de circuito de processamento de leite. O circuito é composto por uma tubulação de aço inoxidável AISI 304, com 1,9 cm de diâmetro e 5,8 m de comprimento, além de um tanque de 25 L, utilizado como reservatório do produto e das soluções sanitizantes. O reservatório foi acoplado a uma bomba centrífuga de ½ HP, para impulsionar o alimento ou soluções de higienização pelo sistema equipado com cupons de prova em aço inoxidável nas formas cilíndrica, cotovelo 90º e T. As velocidades de circulação foram de 0,5, 1,0 e 1,5 m.s-1, correspondentes a fluxo turbulento com número de Reynolds de 14.000, 28.000 e 42.000, respectivamente. Quando se utilizou velocidade de 0,5 m.s-1, permaneceram aderidas à superfície 10,7% das células. Já nas velocidades e 1,0 e 1,5 m.s-1 as porcentagens de adesão foram de 5,36 e 4,9%, respectivamente, o que demonstra uma menor remoção de células aderidas à medida que o fluxo diminui, permitindo assim que mais células permaneçam aderidas na linha de produção, o que pode favorecer a formação de biofilmes.The influence of the flow milk circulation in the bacterial adhesion of Pseudomonas aeruginosa was evaluated by simulation tests through a circuit model of milk processing. The circuit is composed of a tubulation of stainless steel AISI 304, with 1.9 cm of diameter, 5.8 m of length and a tank of 25 L used as the reservoir of the product and sanitizer solutions. The reservoir was coupled to a centrifugal bomb of ½ HP to impel the food or sanitizer solutions for the system equipped with 90º and T cylindrical stainless steel specimens. The speed of circulation values were 0.5, 1.0 and 1.5 m.s-1, corresponding to turbulent flow with number of Reynolds 14.000, 28.000 and 42.000, respectively. When flow of 0.5 m.s-1 was used 10.7% the

  11. Estudio de las aplicaciones de gestión de la red WAN de un operador de telecomunicaciones

    OpenAIRE

    González Medina, Mariano

    2012-01-01

    Este proyecto se basa en analizar y estudiar exhaustivamente las aplicaciones de gestión de la red WAN de un operador de telecomunicaciones (OdT). Dichas aplicaciones se dividen en dos fases importantes: provisión y mantenimiento. Aquest projecte es basa en analitzar i estudiar exhaustivament les aplicacions de gestió de la xarxa WAN d'un operador de telecomunicacions (OdT). Aquestes aplicacions es divideixen en dues fases importants: provisió i manteniment.

  12. Microstructures of friction surfaced coatings. A TEM study; Gefuege durch Reibauftragschweissen aufgetragener Beschichtungen. Eine TEM-Untersuchung

    Energy Technology Data Exchange (ETDEWEB)

    Akram, Javed; Kalvala, Prasad Rao; Misra, Mano [Utah Univ., Salt Lake City, UT (United States). Dept. of Metallurgical Engineering; Dilip, J. John Samuel [Louisville Univ., KY (United States). Dept. of Industrial Engineering; Pal, Deepankar; Stucker, Brent [Louisville Univ., KY (United States). Dept. of Industrial Engineering; 3D Sim, Park City, UT (United States)

    2016-05-15

    The microstructures of dissimilar metal welds between 9Cr-1Mo (Modified) (P91) and austenitic stainless steel (AISI 304) with Ni-based alloy interlayers (Inconel 625, Inconel 600 and Inconel 800H) are reported. These interlayers were deposited by the friction surfacing method one over the other on P91 alloy, which was finally friction welded to AISI 304. In this paper, the results of microstructural evolution in the friction surfaced coated interlayers (Inconel 625, 600, 800H) are reported. For comparative purposes, the microstructures of consumable rods (Inconel 625, 600, 800H) and dissimilar metal base metals (P91 and AISI 304) were also reported. Friction surfaced coatings exhibited dynamic recrystallization. In friction surfaced coatings, the carbide particles were found to be finer and distributed uniformly throughout the matrix, compared to their rod counterparts.

  13. Microstructures of friction surfaced coatings. A TEM study

    International Nuclear Information System (INIS)

    Akram, Javed; Kalvala, Prasad Rao; Misra, Mano

    2016-01-01

    The microstructures of dissimilar metal welds between 9Cr-1Mo (Modified) (P91) and austenitic stainless steel (AISI 304) with Ni-based alloy interlayers (Inconel 625, Inconel 600 and Inconel 800H) are reported. These interlayers were deposited by the friction surfacing method one over the other on P91 alloy, which was finally friction welded to AISI 304. In this paper, the results of microstructural evolution in the friction surfaced coated interlayers (Inconel 625, 600, 800H) are reported. For comparative purposes, the microstructures of consumable rods (Inconel 625, 600, 800H) and dissimilar metal base metals (P91 and AISI 304) were also reported. Friction surfaced coatings exhibited dynamic recrystallization. In friction surfaced coatings, the carbide particles were found to be finer and distributed uniformly throughout the matrix, compared to their rod counterparts.

  14. Caracterización termomecánica de aceros inoxidables austeníticos AISI-304

    OpenAIRE

    El Wahabi, Mohammed

    2003-01-01

    El control de la microestructura necesita la optimización de las condiciones del conformado en caliente. La recristalización dinámica es el fenómeno protagonista durante un proceso termomecánico, por lo que tiene un interés industrial, permitiendo mejorar las propiedades mecánicas de los aceros inoxidables mediante el afinamiento de grano, y al mismo tiempo aumentar la resistencia a la fragilización y a la corrosión. El objetivo principal de este trabajo es estudiar el comportamiento termomec...

  15. Decomposition kinetics of expanded austenite with high nitrogen contents

    DEFF Research Database (Denmark)

    Christiansen, Thomas; Somers, Marcel A. J.

    2006-01-01

    This paper addresses the decomposition kinetics of synthesized homogeneous expanded austenite formed by gaseous nitriding of stainless steel AISI 304L and AISI 316L with nitrogen contents up to 38 at.% nitrogen. Isochronal annealing experiments were carried out in both inert (N2) and reducing (H2......) atmospheres. Differential thermal analysis (DTA) and thermogravimetry were applied for identification of the decomposition reactions and X-ray diffraction analysis was applied for phase analysis. CrN precipitated upon annealing; the activation energies are 187 kJ/mol and 128 kJ/mol for AISI 316L and AISI 304L...

  16. Mindfulness: Conceptos generales, psicoterapia y aplicaciones clínicas.

    OpenAIRE

    Vásquez-Dextre, Edgar R.

    2016-01-01

    El objetivo de este artículo es presentar una revisión sobre el concepto de Mindfulness, su uso en la psicoterapia y sus aplicaciones clínicas. Mindfulness es una técnica de meditación que consiste en observar la realidad en el momento presente, sin intenciones de juzgar y conplena apertura y aceptación. Existen terapias que usan Mindfulness dentro de su estructura y sus programas, tales como como la Terapia Dialéctico-Conductual y la Reducción del Estrés basada en Mindfulness. Mindfulness ha...

  17. Implantes personalizados de polimetilmetacrilato (PMMA) para aplicaciones en craneoplastia

    OpenAIRE

    Arango Ospina, Marcela

    2014-01-01

    Los implantes a la medida para aplicaciones en craneoplastias tienen el objetivo de restaurar la protección del cerebro que el cráneo proporcionaba y mejorar el aspecto de la superficie después de sufrir un traumatismo o para corregir una malformación. Los principales inconvenientes del procedimiento de craneoplastia incluyen la individualización de la geometría y las propiedades mecánicas del implante para que sea funcional. El objetivo de nuestra investigación fue proponer un...

  18. Gestión de organizaciones: enfoques y aplicaciones

    OpenAIRE

    Zárate, Rodrigo; Argüelles Pabón, Denise Caroline; Aparicio García, Santiago; Largacha Martínez, Carlos; Pérez Uribe, Rafael; de la Hoz, Gerardo A.

    2013-01-01

    Una buena gestión puede transformar una organización. El libro Gestion de organizaciones enfoques y aplicaciones, realiza un análisis de todos los aspectos relevantes que llevan a una organización a generar nuevas y mejores prácticas para el impulso de su productividad y competitividad. se estudian diferentes modelos de gestión con el fin de potencializar el aprendizaje organizacional, es decir la gestión del conocimiento, del talento y la gestión por competencias....

  19. Aplicaciones de redes neuronales en economía.

    Directory of Open Access Journals (Sweden)

    Pacheco Bonrostro, J.

    1997-01-01

    Full Text Available La metodología de las Redes Neuronales Artificiales, está siendo usada con profusión, dentro del campo de la Economía, hasta tal punto que existe una publicación bimensual, que trata específicamente estas aplicaciones a los mercados financieros: Neurove$t Journal. En este trabajo, se presentan las principales líneas de investigación existentes, a continuación la que nosotros estamos siguiendo, con algunos resultados iniciales, para finalizar con las líneas a seguir y una selección bibliográfica.

  20. Aircraft Steels

    Science.gov (United States)

    2009-02-19

    component usage. PH 13-8Mo is a precipitation-hardenable martensitic stainless steel combining excellent corrosion resistance with strength. Custom 465 is...a martensitic , age-hardenable stainless steel capable of about 1,724 MPa (250 ksi) UTS when peak-aged (H900 condition). Especially, this steel can...NOTES 14. ABSTRACT Five high strength steels (4340, 300M, AerMet 100, Ferrium S53, and Hy-Tuf) and four stainless steels (High Nitrogen, 13

  1. Corrosion behavior of low energy, high temperature nitrogen ion ...

    Indian Academy of Sciences (India)

    Corrosion behavior of low energy, high temperature nitrogen ion-implanted AISI 304 stainless steel. M GHORANNEVISS1, A SHOKOUHY1,∗, M M LARIJANI1,2,. S H HAJI HOSSEINI 1, M YARI1, A ANVARI4, M GHOLIPUR SHAHRAKI1,3,. A H SARI1 and M R HANTEHZADEH1. 1Plasma Physics Research Center, Science ...

  2. Regional Meeting on Chemistry - Book of abstracts

    International Nuclear Information System (INIS)

    1980-01-01

    Preparation and characterization of rare earth complexes; corrosion of AISI-304 steel, in ethanol; photolysis of ruthenium complexes; preparation of chromium-51 by irradiation of vanadium; separation of rare earths by using Zn 2+ and Amberlite IR-120 are described. (A.R.H.) [pt

  3. EXPERIMENTAL PREDICTION AND OPTIMIZATION OF MATERIAL ...

    African Journals Online (AJOL)

    It investigates the influence of machining process parameters such as cutting speed, feed rate and depth of cut on the material removal rate (output parameter) during hard turning of AISI 304L austenitic stainless steel (0.03 wt. % C (max)). A total of 27 experiments were conducted using a MORISEIKI SL-253B CNC machine ...

  4. Effect of Adenine Concentration on the Corrosion Inhibition of Aisi ...

    African Journals Online (AJOL)

    This gave a surface coverage of 0.8956 and corrosion penetration rate of 0.022132mm/yr. Hence, the best adenine concentration for the corrosion inhibition of alloys 304L in 1.0M sulphuric acid solution to obtain optimum inhibition efficiency is 0.011M. Keywords: Corrosion, AISI 304L Steel, Inhibition efficiency, Degree of ...

  5. Effects of vegetable-based cutting fluids on the wear in drilling

    Indian Academy of Sciences (India)

    2016-08-26

    Aug 26, 2016 ... In this study, performances of three VBCFs developed from crude sunflower oil, refined sunflower oil, refined canola oil and commercial semi-synthetic cutting fluid are compared in terms of tool wear, thrust force and surface roughness during drilling of AISI 304 austenitic stainless steel with HSSE tool.

  6. Properties of alumina films prepared by metal-organic chemical vapour deposition at atmospheric pressure in hte presence of small amounts of water

    NARCIS (Netherlands)

    Haanappel, V.A.C.; Haanappel, V.A.C.; van Corbach, H.D.; Rem, J.B.; Fransen, T.; Gellings, P.J.

    1995-01-01

    Thin alumina films were deposited on stainless steel, type AISI 304. The deposition process was carried out in nitrogen with low partial pressures of water (0–2.6 × 10−2 kPa (0−0.20 mmHg)) by metal-organic chemical vapour deposition (MOCVD) with aluminium-tri-sec-butoxide (ATSB) as the precursor.

  7. Evaluación de los Frameworks en el Desarrollo de Aplicaciones Web con Python

    OpenAIRE

    Jimmy Rolando Molina Ríos; Nancy Magaly Loja Mora; Mariuxi Paola Zea Ordóñez; Erika Lizbeth Loaiza Sojos

    2016-01-01

    Debido a la creciente interacción de los usuarios con sistemas web, surge la necesidad de combinar las funcionalidades de aplicaciones clásicas de escritorio, con la accesibilidad y bajo costo de la publicación de aplicaciones web; dando origen a la elección del mejor marco de trabajo que se adopte a las necesidades de los desarrolladores. Esta investigación presenta un análisis comparativo de los frameworks que trabajan con el lenguaje Python para el desarrollo de aplicaciones web. Para ello...

  8. Seguridad de aplicaciones híbridas para dispositivos móviles

    OpenAIRE

    Pérez-Pérez, Iván

    2014-01-01

    El presente Trabajo Fin de Máster consiste en un estudio comparativo de las distintas soluciones para el desarrollo de aplicaciones híbridas para móviles (esto es, aplicaciones diseñadas con tecnologías web, pero empaquetadas en contenedores nativos) desde el punto de vista de la seguridad. Se realizará un análisis sobre el estado actual de las aplicaciones híbridas y las tecnologías que se emplean en la creación de las mismas. Se desarrollará una prueba de concepto usando u...

  9. Steel making

    CERN Document Server

    Chakrabarti, A K

    2014-01-01

    "Steel Making" is designed to give students a strong grounding in the theory and state-of-the-art practice of production of steels. This book is primarily focused to meet the needs of undergraduate metallurgical students and candidates for associate membership examinations of professional bodies (AMIIM, AMIE). Besides, for all engineering professionals working in steel plants who need to understand the basic principles of steel making, the text provides a sound introduction to the subject.Beginning with a brief introduction to the historical perspective and current status of steel making together with the reasons for obsolescence of Bessemer converter and open hearth processes, the book moves on to: elaborate the physiochemical principles involved in steel making; explain the operational principles and practices of the modern processes of primary steel making (LD converter, Q-BOP process, and electric furnace process); provide a summary of the developments in secondary refining of steels; discuss principles a...

  10. Comportamiento de la Resistencia al desgaste erosivo de recubrimientos de alúmina

    Directory of Open Access Journals (Sweden)

    Alfonso Santos Jaimes

    2018-01-01

    Full Text Available This article presents the results of the research related to the experimental behavior of alumina coatings obtained from micrometric size particles and deposited through a thermal spraying by flame process on an AISI 304 stainless steel substrate when it is subjected to erosive wear caused by cavitation through a vibratory apparatus. The methodology used to reach the proposed objective consisted of five phases in the first a morphological and chemical characterization of the materials used, was carried out; the second was the adaptation of UIP1000hd ultrasound equipment to the requirements demanded by the ASTM G32-16 standard (standard test method for erosion by cavitation using vibrating apparatus; afterwards, test pieces of AISI 304 stainless steel were tested to verify the performance of the equipment used, the validation of the wear phenomenon present in the specimens was carried out through scanning electron microscopy tests in order to observe the evolution of the footprint left over the specimen; as a fourth phase, the deposition of the alumina coatings was carried out through a conventional oxyacetylene combustion equipment and an Eutalloy 85 BX gun; finally micro-hardness and erosive wear resistance tests were carried out on AISI 304 stainless steel specimens without and with alumina coatings. The results obtained allowed to validate the operation of the adapted equipment for the performance of the tests since the percentage of average error between the experimental and theoretical data was of 4,5% for AISI 304 stainless steel; regarding the behavior of alumina coatings a 26,23% reduction of material loss was obtained with respect to the AISI 304 stainless steel which represents a significant improvement and encourages its use when mechanical elements are subjected to erosive wear caused by cavitation.

  11. Reduction of Friction of Metals Using Laser-Induced Periodic Surface Nanostructures

    OpenAIRE

    Zhuo Wang; Quanzhong Zhao; Chengwei Wang

    2015-01-01

    We report on the effect of femtosecond-laser-induced periodic surface structures (LIPSS) on the tribological properties of stainless steel. Uniform periodic nanostructures were produced on AISI 304L (American Iron and Steel Institute steel grade) steel surfaces using an 800-nm femtosecond laser. The spatial periods of LIPSS measured by field emission scanning electron microscopy ranged from 530 to 570 nm. The tribological properties of smooth and textured surfaces with periodic nanostructures...

  12. MITIGATION OF AGRICULTURAL ENERGY REQUIREMENT IN BANGLADESH USING MICROALGAE PRODUCTION

    OpenAIRE

    Mohammad Farzid Hasan; Syeda Zohra Halim; Choudhury Mohammad Shahariar; Noor Quddus

    2013-01-01

    A high quality joint between tool steel and stainless steel alloys is hard to achieve with the conventional welding process. In this study, a new process of joining semi-solid AISI D2 tool steel and AISI 304 stainless steel using a partial remelting method is proposed. Metallographic analysis and Vickers hardness tests were performed. The results obtained from investigating the basic geometries demonstrated a good joining quality that differs from the conventional process of welding or mechan...

  13. Stress Corrosion Cracking of Aluminum Alloys

    Science.gov (United States)

    2012-09-10

    Hossain and B. J, O’Toole: Stress Corrosion Cracking of Martensitic Stainless Steel for Transmutation Application, Presented at 2003 International...SCC of marternsitic stainless steel by Roy,[12] and learn the annealing effect on SCC of carbon steel by Haruna.[13] The application of slow...observations. In his study on SCC of AISI 304 stainless steel , Roychowdhury[3] detected no apparent SCC in solutions containing 1 ppm thiosulfate and

  14. Aplicaciones del Just-In-Time en la Argentina

    OpenAIRE

    Enrique Yacuzzi; Carolina Fajntich; María Pía Romeo

    2013-01-01

    Este trabajo presenta el concepto de JIT (Just-In-Time, o justo a tiempo) y ofrece aplicaciones en la Argentina. En la Parte I, pone el JIT en el contexto de la gestión japonesa (management japonés): destaca las características de esta gestión, y resume su evolución a lo largo de las últimas décadas. Hace hincapié en la gestión de la producción y analiza los desafíos, críticas y las teorías de la convergencia con los sistemas occidentales que se han examinado a lo largo de los últimos 20 años...

  15. Uso de las TIC en el Trastorno de Espectro Autista: aplicaciones

    Directory of Open Access Journals (Sweden)

    Susana García Guillén

    2016-11-01

    Full Text Available A través de este trabajo de investigación se ha realizado una revisión bibliográfica detallada sobre el uso de las aplicaciones y el autismo. En primer lugar se ha realizado un recorrido histórico a través del concepto autismo y las aplicaciones disponibles. Los objetivos generales han sido conocer la evolución del término autismo, conocer la bibliografía relacionada con el autismo y el uso de aplicaciones, así como las aplicaciones disponibles para niños autistas. A través de las dos bases de datos, dialnet y google aplicaciones, se presenta la revisión sistemática realizada. Como resultado, se han seleccionado cuatro artículos a través de la base de datos dialnet y treinta y cinco aplicaciones. Las Tecnologías de la Información y Comunicación (TIC ofrecen a los usuarios diferentes beneficios como la estimulación de los sentidos y el desarrollo de habilidades que le ayuden a la integración, mejorando sus habilidades sociales para lograr una mejor relación con sus iguales.

  16. Creación de un Framework de desarrollo de aplicaciones para la web con lenguaje PHP

    OpenAIRE

    Henríquez Chavarría, José Antonio

    2013-01-01

    El desarrollo de Frameworks, para desarrollo de aplicaciones en ambiente web, ha tenido un notable aumento, en los últimos años, debido a la necesidad de crear aplicaciones web y la urgencia de muchos por conseguir desarrollos con un ciclo de vida rápido, de forma que actualmente muchos desarrolladores de software requieren herramientas como un Framewok para lograr programar sus aplicaciones y dar seguimiento para siguientes versiones. El presente proyecto se plantea como una alternativa s...

  17. Reconfigurando aplicaciones multi-cloud con líneas de producto software dinámicas

    OpenAIRE

    Cubo, Javier; Gámez,Nadia; Pimentel, Ernesto; Fuentes, Lidia

    2016-01-01

    La reconfiguración dinámica de aplicaciones multi-cloud es un reto complejo aún no suficientemente explorado. En estos entornos las aplicaciones o sus módulos pueden estar desplegados en diferentes proveedores. Por lo tanto, reconfigurar en tiempo de ejecución estas aplicaciones puede requerir la modificación de la distribución en múltiples y heterogéneos proveedores. Obtener la nueva distribución para que sigan funcionando correctamente las aplicaciones no es una tarea senc...

  18. Applications of the renewable energies; Aplicaciones de las energias renovables

    Energy Technology Data Exchange (ETDEWEB)

    Gomez Rocha, Luis Martin [Comision Nacional para el Ahorro de Energia, Mexico, D.F. (Mexico)

    2001-07-01

    The solar energy manifests itself in different forms and its application has been fundamental for the humankind development. These forms are known as renewable energies, since they are energy forms that are renewed or remade with time or that are so abundant on Earth, that they will last for hundreds or thousands of years, either we use them or not. The main advantage of the utilization of the renewable energies in comparison with hydrocarbons is the one of having smaller impact on the environment, which brings about the conservation of nonrenewable resources, and to postpone its exhaustion. They allow the distributed generation, diminishing the power losses in the transmission and distribution systems, which increases the overall efficiency. In addition they can be the drive for regional development and generation of employment, because when having applications in remote zones and being a field still not completely developed in Mexico, the possibility exists of enabling professionals and technicians. From the point of view of the power sector, the renewable energies extend the supply and availability of energy, making more flexible and independent the operation and reliability of the national power system. [Spanish] La energia solar se manifiesta de diversas formas y su aplicacion ha sido fundamental para el desarrollo de la humanidad. A estas formas se les conoce como energias renovables, ya que son formas de energia que se van renovando o rehaciendo con el tiempo o que son tan abundantes en la tierra, que perduraran por cientos o miles de anos, las usemos o no. La principal ventaja del aprovechamiento de las energias renovables en comparacion con los hidrocarburos es la de tener menor impacto al medio ambiente, lo que trae consigo la conservacion de recursos no renovables, y posponer su termino. Permiten la generacion distribuida, disminuyendo las perdidas energeticas en los sistemas de transmision y distribucion, lo que incrementa la eficiencia general. Ademas

  19. Codificación de red y sus aplicaciones

    Directory of Open Access Journals (Sweden)

    Francisco de Asís López Fuentes

    2014-01-01

    Full Text Available Este documento presenta una revisión general de una nueva técnica en el campo de la teoría de la información, llamada “codificación de red”. La codificación de red se presenta como una técnica prometedora y de activa investigación en la teoría de redes. Diversos beneficios relacionados al flujo de información, tales como un óptimo aprovechamiento del ancho de banda y la reducción de retardos en redes de extremo a extremo han sido reportados en la literatura. Nuestro trabajo en este documento se enfoca principalmente a los siguientes aspectos de codificación de red: planteamiento del modelo, áreas de aplicación y beneficios obtenidos al usar esta técnica. Los aspectos discutidos en este trabajo cubren tanto a las redes fijas como móviles. El objetivo de este artículo es mostrar al lector la relevancia y potencial de esta técnica y las aplicaciones que se están desarrollando a su alrededor.

  20. Aplicaciones del GRC en España y Argelia

    Directory of Open Access Journals (Sweden)

    Rodríguez Santiago, Jesús

    1986-09-01

    Full Text Available Not Available.Este artículo resume la experiencia obtenida en la utilización del mortero de cemento reforzado con fibra de vidrio (GRC en el campo de la construcción. Se describen en primer lugar las características del material y el proceso de fabricación en factoría de paneles de GRC. Se exponen a continuación algunas realizaciones llevadas a cabo con este material destacando, por su volumen y rapidez de ejecución, el conjunto de fachadas para edificios de viviendas, hospitales y centros escolares construidos en Argelia. También se comentan otras aplicaciones del GRC para la rehabilitación y decoración interior de edificios y para la construcción de elementos singulares. Finalmente, en el apartado de las conclusiones se menciona la necesidad de seguir investigando en el comportamiento a largo plazo de este material para poder aumentar su utilización en la construcción.

  1. Propiedades y aplicaciones de los cementos alcalinos Properties and uses of alkali cements

    Directory of Open Access Journals (Sweden)

    Ana Fernández-Jiménez

    2009-12-01

    Full Text Available En este trabajo se presentan algunas de las propiedades tecnológicas de los materiales cementantes elaborados por activación alcalina de aluminosilicatos. Más específicamente sobre las propiedades de morteros y hormigones elaborados con cenizas volantes activadas alcalinamente (sin cemento Portland. Así en función del tipo de activador alcalino empleado y tras un curado térmico previo, el material resultante presentará una interesante lista de propiedades y características que incluyen: elevadas resistencias mecánicas iniciales (a flexión y a compresión, baja retracción al secado, y una muy buena adherencia matriz-acero, así como una excelente resistencia al ataque ácido y un excelente comportamiento frente al fuego. Es por ello que estos nuevos cementos debido a sus magnificas características tecnológicas y durables, así como a la facilidad de adecuarlos a las instalaciones existentes en la industria de los prefabricados, pueden ser fácilmente utilizados en diversas aplicaciones como por ejemplo: elaboración de durmientes para el ferrocarril, bloques para edificación o pavimentación, etc.In this paper are presented some of the technologic properties of cementitious material elaborated by alkali activation of aluminosilicates are presented. More specifically it is about the properties of alkali activated fly ash concrete and mortar (without Portland cement. So depending on the type of alkali activator that is used and after a previous thermal curing, the resulting material will show an interesting list of properties and features that includes: high initial mechanical strengths (under flexure and compression, low drying shrinkage, and a very good matrix-steel bonding, as well as an excellent strength to acid attack and an excellent behaviour when is exposed to fire. That is the reason why these new cements, due to their magnificent and durable technologic features as well as its easy adaptability to the existing

  2. Aplicaciones científicas numéricas: El (ciclo de vida del) Software heredado

    OpenAIRE

    Méndez, Mariano; Tinetti, Fernando Gustavo

    2012-01-01

    El objetivo de esta línea de investigación es el estudio de las aplicaciones científicas de cómputo numérico desde el punto de vista de la Ingeniería de Software y del Procesamiento Paralelo. Además, se orienta a desarrollar técnicas y herramientas destinadas a reestructurar dichas aplicaciones permitiendo que éstas evolucionen a través del tiempo mejorando sus prestaciones y su estructura.

  3. Mashup d'aplicacions basat en un buscador intel·ligent

    OpenAIRE

    Sancho Piqueras, Javier

    2010-01-01

    Mashup de funcionalitats, basat en un cercador intel·ligent, en aquest cas pensat per a cursos, carreres màsters, etc. La finalitat és adjuntar diverses aplicacions amb l'únic propòsit que en aquest cas és un buscador però que també ens permet utilitzar eines per a la connectivitat mitjançant web Services, o xarxes socials. Mashup de funcionalidades, basado en un buscador inteligente, en este caso pensado para cursos, carreras másters, etc. La finalidad es juntar diversas aplicaciones con ...

  4. Application of frequency converters in industry; Aplicacion de convertidores de frecuencia en la industria

    Energy Technology Data Exchange (ETDEWEB)

    Adame Gonzalez, A.; Aguilar Galvan, A. [Ingenieria Energetica Integral, S.A. de C.V. (Mexico)

    1997-12-31

    Some of the applications of the frequency converters will be analyzed, as well as the parameters to be considered for the feasibility of its application evaluation. It is also described how an energy evaluation is accomplished and finally a series of actions are enlisted conducting to the energy savings. [Espanol] Se presentaran algunas de las aplicaciones de los convertidores de frecuencia. Ademas se indicaran los parametros a registrar para evaluar la factibilidad de aplicacion de los mismos, se describe como ejecutar la evaluacion energetica y finalmente se listan una serie de acciones que conducen a lograr ahorros de energia.

  5. Sistema para la monitorización y estudio de aplicaciones maliciosas para Android

    OpenAIRE

    Gutiérrez Hernández, Sergio

    2014-01-01

    Los teléfonos móviles inteligentes (smartphones) se han posicionado como aparatos altamente populares con grandes capacidades de cómputo, comunicación y sensorización. Estos dispositivos se caracterizan por su habilidad para incorporar aplicaciones desarrolladas por terceras partes, capaces de acceder a los servicios proporcionados por el smartphone. En este contexto, hemos podido observar durante los últimos años un crecimiento exponencial en el número de muestras de aplicaciones haciendo un...

  6. Application of frequency converters in industry; Aplicacion de convertidores de frecuencia en la industria

    Energy Technology Data Exchange (ETDEWEB)

    Adame Gonzalez, A; Aguilar Galvan, A [Ingenieria Energetica Integral, S.A. de C.V. (Mexico)

    1998-12-31

    Some of the applications of the frequency converters will be analyzed, as well as the parameters to be considered for the feasibility of its application evaluation. It is also described how an energy evaluation is accomplished and finally a series of actions are enlisted conducting to the energy savings. [Espanol] Se presentaran algunas de las aplicaciones de los convertidores de frecuencia. Ademas se indicaran los parametros a registrar para evaluar la factibilidad de aplicacion de los mismos, se describe como ejecutar la evaluacion energetica y finalmente se listan una serie de acciones que conducen a lograr ahorros de energia.

  7. Identificación de prestaciones en nuevas aplicaciones de vidrio estructural

    OpenAIRE

    Abascal Capilla, Alba

    2016-01-01

    El presente Trabajo Fin de Grado consiste en la identificación de las prestaciones que se deben cumplir de cara al diseño de los elementos de vidrio estructural para aplicaciones actuales, novedosas e innovadoras. Para la identificación de las prestaciones se comienza por una evaluación del estado actual del vidrio; posteriormente se hace una selección de obras innovadoras en aplicaciones existentes con vidrio estructural (fachadas, cubiertas, barandillas, suelos, escaleras, pilares y viga...

  8. Stainless-Steel-Gadolinium Alloys; Alliages Acier Inoxydable-Gadolinium; Splavy iz nerzhaveyushchej stali i gadoliniya; Aleaciones de Acero Inoxidable-Gadolinio

    Energy Technology Data Exchange (ETDEWEB)

    Copeland, M.; Kato, H. [Albany Metallurgy Research Center, Bureau Of Mines, United States Department of the Interior, Albany, OR (United States)

    1964-06-15

    mineures ont une grande influence sur les structures resultant de traitements equilibrants et sur les possibilites de transformation des aciers. Lorsque le gadolinium est melange a de l 'acier au chrome et au nickel, deux phases mineures, Fe{sub 9}Gd et Ni{sub 7}Gd, fondent a 1080 Degree-Sign C, ce qui impose une limite superieure aux temperatures de traitement a chaud et de transformation. Les auteurs ont pu facilement transformer des alliages comprenant jusqu'a 5 Degree-Sign Io en poids de gadolinium et determiner leurs caracteristiques mecaniques et leur resistance a la corrosion. Ils n'ont observe aucun changement dans les caracteristiques mecaniques de l'acier ou sa resistance a la corrosion par l'eau chaude, lorsqu'ils lui ont ajoute'jusqu'a 3% en poids de gadolinium. En raison des limites imposees aux temperatures de transformation des aciers au chrome et au nickel par le point de fusion des phases mineures, les auteurs ont etudie les effets du gadolinium sur des aciers au chrome. Ils ont releve une seule phase mineure qui fond a 1320 Degree-Sign C en etudiant l 'isoplethe du gadolinium a 10% en poids dans l 'alliage chrome-fer-gadolinium. Cette propriete permettrait d'equilibrer et de transformer ces aciers au gadolinium aux temperatures auxquelles on opere normalement. (author) [Spanish] En vista de la excelente resistencia a la corrosion de los aceros inoxidables y del interes que presenta el gadolinio como veneno nuclear, se han estudiado aleaciones de esos dos metales. El gadolinio fue aleado con aceros inoxidables de tipo AISI-304 y al cromo, y se estudiaron las relaciones de fase, la facilidad de trabajo y las propiedades de estas aleaciones. Se observo que en las aleaciones que contienen bajos porcentajes de gadolinio, los puntos de fusion de las fases menores ejercen un efecto muy marcado sobre las estructuras resultantes de los tratamientos de equilibracion y sobre la facilidad de trabajo de los afceros. Cuando se alea el gadolinio con acerce al cromo

  9. Tool steels

    DEFF Research Database (Denmark)

    Højerslev, C.

    2001-01-01

    On designing a tool steel, its composition and heat treatment parameters are chosen to provide a hardened and tempered martensitic matrix in which carbides are evenly distributed. In this condition the matrix has an optimum combination of hardness andtoughness, the primary carbides provide...... resistance against abrasive wear and secondary carbides (if any) increase the resistance against plastic deformation. Tool steels are alloyed with carbide forming elements (Typically: vanadium, tungsten, molybdenumand chromium) furthermore some steel types contains cobalt. Addition of alloying elements...... serves primarily two purpose (i) to improve the hardenabillity and (ii) to provide harder and thermally more stable carbides than cementite. Assuming proper heattreatment, the properties of a tool steel depends on the which alloying elements are added and their respective concentrations....

  10. Células tronco mesenquimales: definiciones, cultivo y aplicaciones potenciales

    Directory of Open Access Journals (Sweden)

    Willy Ceron

    Full Text Available En los últimos años, las células troncales mesenquimales (Mesenchymal Stem Cells, MSC han adquirido mucha importancia debido a su gran plasticidad y su capacidad de liberar factores paracrinos con capacidad de interactuar con diversos tipos celulares, tejidos y órganos. El uso de MSC en medicina regenerativa es importante debido a que, al no expresar las moléculas del complejo mayor de histocompatibilidad (MHC clase II ni moléculas co-estimuladoras y tener baja expresión del MHC clase I, haría que no sean rechazadas por individuos de la misma especie, es posible utilizarlas no sólo de manera autóloga, sino también, eventualmente, alogénica. Sin embargo, es importante demostrar científicamente muchas de sus propiedades, entre ellas las inmunomoduladoras. Al tener varias fuentes de obtención, se debe estandarizar la que sea la mejor para garantizar la pureza y calidad de las MSC. Finalmente, es importante que cuando se trabaje con estas células se demuestre completamente las características del cultivo celular, la inmunotipificación y su capacidad de diferenciación. Se están ensayando muchas aplicaciones clínicas de las MSC. Dentro de ellas, su capacidad para mejorar la recuperación y potencial curación de úlceras crónicas como las diabéticas, ha atraído la atención por su potencial impacto terapéutico.

  11. evaluación de conceptos y aplicaciones

    Directory of Open Access Journals (Sweden)

    Naomar Almeida-Filho

    2006-01-01

    Full Text Available Varios elementos epistemológicos y metodológicos han sido propuestos como tendencia alternativa a la ciencia contemporánea, agrupados bajo el rótulo de "nuevo paradigma" y con diferentes grados de interarticulación. Estos elementos sugieren que una nuova scienza se encuentra en desarrollo, demandando categorías epistemológicas propias (como la categoría de la complejidad, nuevos modelos teóricos (como la "teoría del caos" y nuevas formas lógicas de análisis (como los modelos matemáticos no lineales, la geometría fractal, la lógica borrosa y la teoría de redes. También en el campo de la Salud Colectiva, varios autores han defendido la necesidad de nuevos paradigmas. Esas propuestas vienen siendo ampliadas y difundidas con el objetivo de fomentar una producción científica concreta, capaz de alimentar efectivamente un posible paradigma nuevo. En este texto se pretende presentar brevemente los principales enfoques que representan algún tipo de cambio paradigmático de un modo general en el seno de la ciencia. También se discuten algunos de los diversos elementos constitutivos del paradigma de la complejidad, desde sus posibles aplicaciones a la problemática de la salud en poblaciones, buscando examinar estas cuestiones en el ámbito de nuestro interés específico e indicando algunas tentativas en el sentido de producir evidencias empíricas para el análisis de la situación de salud, sus efectos y sus determinantes a partir de estos abordajes.

  12. Aplicaciones Web para el desarrollo sostenible a través de ONG

    OpenAIRE

    García Miguel, Daniel

    2008-01-01

    La meta de este proyecto es facilitar el acceso de las ONG a la tecnología Web, y concretamente las aplicaciones Web, para que aquellas que no tengan acceso a servicios profesionales, puedan ser autosufidentes en el desarrollo de sus propias soluciones.

  13. Haré un dibujo aprovechando esta nada. Aplicaciones de dibujo en freeware y opensource

    OpenAIRE

    Horcajada González, Ricardo

    2012-01-01

    Breve presentación de la tipología más común de los diferentes programas de sofware libre dedicados al dibujo que pueden encontrarse como freeware en internet. Aplicaciones y distribución de las imágenes.

  14. Extracción y aplicaciones alimentarias de membranas de cáscaras de huevo

    OpenAIRE

    García Campos, Tania

    2015-01-01

    Caracterización físico-química de la membrana de la cáscara de huevo, seguida del estudio y desarollo de posibles aplicaciones de la membrana en diversos campos, entre los que destaca la formación de geles y la retención de cobre y proteínas.

  15. Aplicaciones del colgajo frontonasal para la cobertura de defectos nasales

    Directory of Open Access Journals (Sweden)

    M. Pérez

    2015-12-01

    Full Text Available Presentamos una revisión retrospectiva de los pacientes a los cuales se realizó un colgajo frontonasal para la cobertura de defectos nasales intervenidos en la Unidad de Tumores Cutáneos de nuestro Servicio en el periodo comprendido entre enero de 2010 y mayo de 2014. El objetivo es analizar nuestras aplicaciones y resultados además de describir un algoritmo que permita indicar los distintos diseños en función de la localización y el tamaño del defecto a reparar. Empleamos el colgajo frontonasal en 78 pacientes (49 mujeres y 29 varones con un rango de edad de 47 a 92 años (media de 73 años. Creamos un total de 81 defectos, puesto que en 3 casos se resecaron simultáneamente 2 tumoraciones, todos de etiología tumoral (64 carcinomas basocelulares, 16 carcinomas espinocelulares y 1 caso de léntigo maligno melanoma, localizados en el área nasal, con un tamaño mínimo de 12 x 17 mm y máximo de 30 x 35 mm (media de 22 x 25 mm. El periodo de seguimiento fue de entre 2 meses y 4 años (media de 2,5 años. Respecto a las complicaciones observadas, todas ellas menores, hubo 6 casos de necrosis marginal, 8 de dehiscencia parcial de la herida y 1 de cicatrización hipertrófica, tratándose en su mayor parte de varones fumadores. Todos los colgajos sobrevivieron con resultado estético satisfactorio. El colgajo frontonasal permite la cobertura en un sólo tiempo quirúrgico de defectos nasales independientemente de su localización, de hasta 30 x 35 mm en nuestra serie. Se trata de un colgajo seguro y versátil en sus múltiples modificaciones, con unos resultados estéticos satisfactorios. Estas ventajas son de especial importancia en pacientes de edad avanzada como alternativa a técnicas más complejas. Se trata por lo tanto, a nuestro juicio, de una opción a tener en cuenta para la reconstrucción en un único tiempo quirúrgico de defectos nasales.

  16. Evaluación de hidrogeles para aplicaciones agroforestales

    Directory of Open Access Journals (Sweden)

    Andrés Barón Cortés

    2007-09-01

    Full Text Available Con hidrogeles sintetizados por medio de la técnica de polimerización en suspensión inversa (PSI, compuestos por acrilamida y acrilato de potasio entrecruzados con N, N’ metilen-bis-acrilamida y que presentan diferentes comportamientos desde el punto de vista de capacidad y velocidad de hinchamiento, módulo elástico y propie-dades de liberación, se estudia la modificación de las propiedades hidráulicas de un suelo tipo franco arcilloso realizando curvas de retención de humedad, empleando ollas de presión de plato cerámico, y se desarrollan montajes para evaluar la modificación en la retención de los mismos, ante condiciones de dosificación prolongada e instantánea de agua de irrigación. Adicionalmente, se realizan cultivos de acacia y rábano en fase vivero en suelos acondicionados con diferentes hidrogeles, en el primer cultivo se evalúa el retraso en la marchitez de la especie y en el segundo la diferencia en crecimiento; simultáneamente para los cultivos, se hace el seguimiento del contenido de humedad in situ del suelo con respecto al tiempo. Se logra un método para la medición del módulo elástico y las propiedades de liberación y se establece un modelo para predecir el comportamiento de los hidrogeles en el suelo con el conocimiento de sus propiedades básicas en el estado libre. Finalmente, los resultados muestran la bondad del uso de hidrogeles en estas aplicaciones: hay mayor facilidad de liberación y retención de agua aprovechable por el suelo, retraso notable del marchitamiento en condiciones hostiles, y es mayor el crecimiento de las especies, entre otros beneficios, además se establecen pautas para definir las características del hidrogel más adecuado dependiendo de la aplicación deseada y se realiza una proyección hacia la disminución del consumo de agua para el mantenimiento de un cultivo.

  17. Steel alloys

    International Nuclear Information System (INIS)

    Bloom, E.E.; Stiegler, J.O.; Rowcliffe, A.F.; Leitnaker, J.M.

    1977-01-01

    The invention deals with a fuel element for fast breeder reactors. It consits essentially of a uranium oxide, nitride, or carbide or a mixture of these fuels with a plutonium or thorium oxide, nitride, or carbide. The fuel elements are coated with an austenitic stainless steel alloy. Inside the fuel elements, vacancies or small cavities are produced by neutron effects which causes the steel coating to swell. According to the invention, swelling is prevented by a modification of type 304, 316, 321, or 12 K 72HV commercial steels. They consist mainly of Fe, Cr, and Ni in a ratio determined by a temary diagram. They may also contain 1.8 to 2.3% by weight of Mo and a fraction of Si (0.7 to 2% by weight) and Ti(0.10 to 0.5% by weight) to prevent cavity formation. They are structurally modified by cold working. (IHOE) [de

  18. Ingeniería de software en el desarrollo de aplicaciones para dispositivos móviles

    OpenAIRE

    Thomas, Pablo Javier; Galdámez, Nicolás; Delía, Lisandro Nahuel; Cristina, Federico; Dapoto, Sebastián H.; Tinetti, Fernando Gustavo; Pesado, Patricia Mabel; De Giusti, Armando Eduardo

    2013-01-01

    Se presenta una línea de investigación y desarrollo que tiene por objeto estudiar temas relacionados con aplicaciones para dispositivos móviles, fundamentalmente aspectos de Ingeniería de Software orientados al desarrollo e implementación de aplicaciones móviles, sobre diversos entornos operativos y el estudio y desarrollo de aspectos de conectividad entre dispositivos móviles.

  19. Hegelian Steel

    DEFF Research Database (Denmark)

    Kjær, Poul F.

    2015-01-01

    Even in our globalized world the notion of national economies remain incredibly strong, just as a considerable part of the literature on transnational governance and globalization continue to rely on a zero-sum perspective concerning the relationship between the national and the transnational. De...... of the European steel industry....

  20. Diseño de una arquitectura para redes de sensores con soporte para aplicaciones de detección de eventos

    OpenAIRE

    LINO RAMIREZ, CARLOS

    2012-01-01

    Las aplicaciones para redes de sensores inalámbricas, o Wireless Sensor Networks (WSNs), han mostrado un crecimiento significativo en los últimos años. Actualmente constituyen una alternativa tecnológica interesante para el desarrollo de aplicaciones que requieren monitorizar constantemente el estado de cualquier variable relacionada con escenarios de diversos ámbitos. Si las aplicaciones detectan cambios en los valores de dichas variables, pueden activar la ejecución de acciones preventivas ...

  1. Comportamiento del acero de baja aleación SA-508 y del acero al carbono A-410b en las condiciones de operación y parada del circuito primario de los reactores de agua ligera tipo PWR

    Directory of Open Access Journals (Sweden)

    García-Redondo, María del Sol

    2000-04-01

    Full Text Available The corrosion rate of low alloy steel SA-508 and carbon steel A-410b in simulated operation and shutdown conditions of pressurized water reactor has been determined. Moreover potentiodynamic polarization curves and galvanic effect through coupling of AISI-304 have been carried out under shutdown simulated condition.

    En este trabajo se ha determinado la cinética de corrosión del acero de baja aleación SA-508 y del acero al carbono A-410b en condiciones que simulan la operación y la parada de los reactores de agua ligera a presión. También se han realizado curvas de polarización potenciodinámica y se ha estudiado el acoplamiento galvánico con AISI-304 en condiciones de parada de los reactores de agua ligera a presión.

  2. Oxide layer stability in lead-bismuth at high temperature

    Science.gov (United States)

    Martín, F. J.; Soler, L.; Hernández, F.; Gómez-Briceño, D.

    2004-11-01

    Materials protection by 'in situ' oxidation has been studied in stagnant lead-bismuth, with different oxygen levels (H 2/H 2O ratios of 0.3 and 0.03), at temperatures from 535 °C to 600 °C and times from 100 to 3000 h. The materials tested were the martensitic steels F82Hmod, EM10 and T91 and the austenitic stainless steels, AISI 316L and AISI 304L. The results obtained point to the existence of an apparent threshold temperature above which corrosion occurs and the formation of a protective and stable oxide layer is not possible. This threshold temperature depends on material composition, oxygen concentration in the liquid lead-bismuth and time. The threshold temperature is higher for the austenitic steels, especially for the AISI 304L, and it increases with the oxygen concentration in the lead-bismuth. The oxide layer formed disappear with time and, after 3000 h all the materials, except AISI 304L, suffer corrosion, more severe for the martensitic steels and at the highest temperature tested.

  3. PATRONES DE MULTICULTURALIDAD PARA EL DISEÑO DE APLICACIONES WEB

    Directory of Open Access Journals (Sweden)

    Víctor Alfonso Zapata

    2014-01-01

    Full Text Available La diversidad cultural en la Web surge como resultado del crecimiento de internet en los últimos años, logrando que los servicios y aplicaciones Web sean cada vez más utilizados por usuarios de diversas culturas, que en muchos casos terminan siendo diferentes a los usuarios iniciales en los que se basó su diseño y construcción. Este trabajo analiza las diferencias que se presentan en la comunicación multicultural a través de la Web, tomando como punto de partida las dimensiones culturales propuestas por Victor, Hofstede, Trompenaars y Hall. Se identificaron los elementos de diseño Web que están relacionados con las dimensiones culturales y su comportamiento en sitios Web representativos de Argentina, Colombia y España para finalmente construir un conjunto de Patrones de Multiculturalidad para el Diseño de Aplicaciones Web.

  4. Resinas acetálicas: diversas aplicaciones en odontoestomatología

    OpenAIRE

    Puigpelat Martí, Ana M.; Casanellas Bassols, Josep M. (Josep Maria)

    1994-01-01

    La resina acetálica o Polioxime­tileno (POM) es un nuevo material estético de reciente aplicación en el campo de la Odontoestomatolo­gía. En este artículo presentamos al­gunas de las aplicaciones donde la estética desempeña una función importante. Una de las aplicaciones de las re­sinas acetálicas es el campo de la Prótesis Parcial Removible, cuan­do queremos sustituir los retene­dores vestibulares convencionales (metálicos) por retenedores más es­téticos. Otra posible aplicación puede ser la...

  5. A quantitative evaluation of the L.B.W. efficiency on AISI 304 bead on plates welded under different focusing and tilted laser beam conditions

    Science.gov (United States)

    Daurelio, Giuseppe; Ludovico, Antonio D.; Lugara, M. P.; De Filippis, L. A. C.; Spera, A. M.; Rocco, S.

    2005-03-01

    The aim of this search is to evaluate the WE (Welding Efficiency) of each beads versus the different positions of the laser beam optical focus (positive or negative or zero values) respect to the work-piece surface and also versus different laser beam incidence angles (80° and 70°) by using two laser power levels (2 and 2.5 KW) and two welding speeds (3 and 6 m/min). The WE values have been reported on two DA.LU. method plots and the relate evaluations regarding the same ones as well as the recorded best parameters have been evidenced.

  6. Comparación entre los diagramas TTS obtenidos mediante los ensayos normalizados Huey y Strauss modificado para el acero inoxidable AISI 304

    Directory of Open Access Journals (Sweden)

    Otero, E.

    1996-04-01

    Full Text Available This work presents a comparison of Temperature-Time-Sensitization TTS diagrams obtained by Huey and modified Strauss standard, for detecting susceptibility to intergranular attack. The difference between these tests is the use of a strong or a slightly smooth oxidizing electrolyte. The diagrams obtained are different and if a sample tested by modified Strauss is sensitized, then it will be sensitized in the Huey test, but the contrary is not always true. This difference is because a sensitized sample has to have a continuous band lacking in chromium along the grain boundary in order to be sensitized in the modified Strauss test. This condition is not necessary in the Huey test.

    Se comparan los diagramas Temperatura-Tiempo-Sensibilización TTS, obtenidos mediante los ensayos normalizados de corrosión intergranular Huey y Strauss modificado, que, respectivamente, utilizan electrólitos fuerte y suavemente oxidantes, mostrándose que los diagramas obtenidos son diferentes. Si una muestra evaluada mediante el ensayo Strauss modificado se encuentra sensibilizada, entonces lo estará también en el ensayo Huey, pero no necesariamente ocurrirá lo contrario; esta diferencia se asocia a la necesidad de la existencia de una zona continua empobrecida en cromo a lo largo del límite de grano para que el material se sensibilice con respecto al ensayo Strauss modificado, condición innecesaria para el caso del ensayo Huey.

  7. “MEDICION DE PARAMETROS GENERADORES DE ESFUERZOS RESIDUALES DURANTE EL PROCESO DE SOLDADURA DE ACERO INOXIDABLE AUSTENITICO AISI 304L”.

    OpenAIRE

    García López, Christian Jesus

    2012-01-01

    En la actualidad los procesos de soldadura por arco eléctrico se han convertido en la técnica por excelencia para la unión del acero y sus aleaciones. Se puede mencionar que la importancia de la soldadura, es tal, que sin ella no serían posibles muchos de los productos y servicios que cotidianamente son consumidos o requeridos por las sociedades contemporáneas actuales. Cada vez con mayor longitud y diámetro se instalan líneas de tubería para la distribución y conducción de tod...

  8. Study of oxide film formed in a pre cracked CT specimen of AISI 304L during a rising displacement test in 288 C water

    International Nuclear Information System (INIS)

    Diaz S, A.; Castano M, V.

    2007-01-01

    A study of oxide film formed inside pre cracked CT specimens during a rising displacement test in high temperature water (288 C) was performed in this study, The environmental conditions used during the experiments were similar to these found in Boiling Water Reactors (BWR): Normal Water Condition (NWC - 200 ppb O 2 ) and Hydrogen Water Chemistry (HWC - 125 ppb H2). The oxide films formed were analyzed by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). In both cases the oxide film consisted of two layers identified as magnetite. In the case of HWC the results agree with previous reports that mention magnetite as a stable phase in reducing conditions. However the stable phase in oxidant conditions is hematite and this work shows the presence of magnetite crystals in the narrow crack of CT specimens in spite of the oxidant environmental condition. This situation confirms that inside the pre-cracked CT specimens the environmental conditions were different from the oxidant bulk, and probably a poor oxygen access and stagnant conditions within the narrow crack promoted a localized reducing environment that permitted the magnetite formation. Is evident that the crack growth studies should consider the conditions inside crack because they are significantly different. (Author)

  9. Arquitecturas multiprocesador en HPC: software, métricas y aplicaciones

    OpenAIRE

    De Giusti, Armando Eduardo; Tinetti, Fernando Gustavo; Naiouf, Marcelo; Chichizola, Franco; De Giusti, Laura Cristina; Villagarcía Wanza, Horacio A.; Montezanti, Diego Miguel; Encinas, Diego; Pousa, Adrián; Rodriguez, Ismael Pablo; Eguren, Sebastián; Iglesias, Luciano; Paniego, Juan Manuel; Pi Puig, Martín; Dell'Oso, Matías

    2016-01-01

    Caracterizar las arquitecturas multiprocesador distribuidas enfocadas especialmente a cluster y cloud computing, con énfasis en las que utilizan procesadores de múltiples núcleos (multicores, GPUs y Xeon Phi), con el objetivo de modelizarlas, estudiar su escalabilidad, analizar y predecir performance de aplicaciones paralelas, estudiar el consumo energético y su impacto en la perfomance así como desarrollar esquemas para detección y tolerancia a fallas en las mismas. Profundizar el estudio...

  10. Aplicaciones de caucho reciclado: Una revisión de la literatura

    Directory of Open Access Journals (Sweden)

    Gabriel Jaime Peláez Arroyave

    2017-01-01

    Full Text Available La generación de residuos de caucho se ha convertido en una preocupación global por su impacto negativo en el medio ambiente y en la salud humana. La legislación ambiental sobre la disposición de este tipo de residuos ha venido aumentando las exigencias a los fabricantes, comercializadores y usuarios, con lo cual se ha acelerado la búsqueda de alternativas para el reaprovechamiento de los residuos de caucho. Este artículo presenta una revisión bibliográfica acerca de las principales tendencias en la utilización del caucho reciclado, incluyendo aplicaciones actualmente comercializadas y otras derivadas tanto de estudios terminados como de líneas de investigación en desarrollo. Las aplicaciones con mayor potencial de volumen consumido son del sector infraestructura y construcciones civiles, especialmente asfaltos, concretos y materiales aislantes para construcción liviana. Algunas aplicaciones con potencial en el futuro cercano son los filtros para la limpieza de aguas contaminadas y como componente en materiales compuestos con matriz termoplástica o en poliuretano. Se evidencia la pertinencia de continuar investigando sobre esta temática, que posee unos retos científicos de alta relevancia, los cuales ameritan la mayor atención por el problema ambiental significativo asociado al manejo de los residuos de caucho.

  11. Comparison between the Norton - and Mukherjee constitutive equations in the determination of stress - strain analysis of a material under creep

    International Nuclear Information System (INIS)

    Bevilacqua, L.; Feijoo, R.A.; Freire, J.L.; Miranda, P.E.V. de; Monteiro, E.; Silveira, T.L. da; Taroco, E.

    1981-06-01

    The Norton and Mukherjee constitutive equations are used to approximate the experimental results of creep in AISI 304 steel. Both equations are applied to the stress-strain analysis of a rotating disk with a concentric circular hole. From the design point of view it is shown that the stresses obtained with both equations are equivalents, which is not true for the velocities. (Author) [pt

  12. Proceedings of the International Congress (12th), Corrosion Control for Low-Cost Reliability, Held in Houston, Texas on September 19 -24, 1993. Volume 3B. Corrosion: Specific Issues

    Science.gov (United States)

    1993-09-24

    de Quimica Pura y Aplicada, Monterrey N.L., 1990. No. 47. 3.- 8. Valdez, G. Guerra, J. Sampedro, N. Rosas. CORROSION, Vol. 2, No. 3, 1991, pp. 11-15...AISI 304L AND 316L STAINLESS STEELS PREPARED BY POWDER METALLURGY. E. Otero Departamento de Ciencia de Materiales Facultad de Ciencias Quimicas ...Madrid, Spain. V. Utrilla Departamento de Ciencia de Materiales Facultad de Ciencias Quimicas Universidad Complutense 28040-Madrid, Spain. E. Sfienz

  13. Characteristics of ion spectrum in a low energy nitrogen operated plasma focus: application to the metallic substrates thermal treatment

    International Nuclear Information System (INIS)

    Kelly, H.; Lepone, A.; Marquez, A.

    1998-01-01

    Full text: This work presents the nitrogen ion spectrum characteristics in a Plasma Focus device, determined using a Thomson spectrometer and a Faraday cup, operated in the secondary electron collective mode. It is also discussed the thermal treatment and the re coating induce by ions incident on a metallic surface (AISI 304 steel) placed in front of the coaxial gun, when the device is operated with a Ti implant at the end of the central electrode

  14. Evaluación de los Frameworks en el Desarrollo de Aplicaciones Web con Python

    Directory of Open Access Journals (Sweden)

    Jimmy Rolando Molina Ríos

    2016-09-01

    Full Text Available Debido a la creciente interacción de los usuarios con sistemas web, surge la necesidad de combinar las funcionalidades de aplicaciones clásicas de escritorio, con la accesibilidad y bajo costo de la publicación de aplicaciones web; dando origen a la elección del mejor marco de trabajo que se adopte a las necesidades de los desarrolladores. Esta investigación presenta un análisis comparativo de los frameworks que trabajan con el lenguaje Python para el desarrollo de aplicaciones web. Para ello el análisis se formuló mediante un modelo de evaluación que se basa en las características de calidad propuestas en la norma ISO/IEC 9126. Estas a su vez permiten establecer sub-características, atributos y métricas para evaluar la calidad de las aplicaciones web. Permitiendo obtener como resultado una matriz para la Evaluación de Frameworks: Django, Pyramid, Turbogear y Web2PY. Los resultados obtenidos mostraron las fortalezas y debilidades de cada framework y fue la base para determinar que Django es el mejor framework para la implementación de desarrollo de sistemas web. Este framework cumplió con todos los indicadores del modelo de evaluación, los resultados redactados al final del documento determinan que tomando en cuenta las métricas de calidad se puede elegir qué marco de trabajo es el que mejor se adapta para el desarrollo de aplicaciones web en la Ciudad de Machala. Antes de realizar una evaluación se considera indispensable conocer y comprender el funcionamiento de los elementos que se vaya a cotejar, para ello es recomendable emplear tablas para la comparación de las características, teniendo como referencia sitios web confiables que aporten documentación sobre los frameworks y el empleo de estándares de calidad para su determinación.

  15. miCole, Social Media for Schools: Estudio de tecnologías para el desarrollo de aplicaciones móviles híbridas.

    OpenAIRE

    Bárcena Díez, Jaime

    2017-01-01

    El objetivo de este proyecto consiste en dar al lector una visión global sobre los diferentes tipos de aplicaciones para dispositivos móviles según su forma de desarrollo. Grado en Ingeniería Informática de Servicios y Aplicaciones

  16. Surface coating of ceria nanostructures for high-temperature oxidation protection

    Science.gov (United States)

    Aadhavan, R.; Bhanuchandar, S.; Babu, K. Suresh

    2018-04-01

    Stainless steels are used in high-temperature structural applications but suffer from degradation at an elevated temperature of operation due to thermal stress which leads to spallation. Ceria coating over chromium containing alloys induces protective chromia layer formation at alloy/ceria interface thereby preventing oxidative degradation. In the present work, three metals of differing elemental composition, namely, AISI 304, AISI 410, and Inconel 600 were tested for high-temperature stability in the presence and absence of ceria coating. Nanoceria was used as the target to deposit the coating through electron beam physical vapor deposition method. After isothermal oxidation at 1243 K for 24 h, Ceria coated AISI 304 and Inconel 600 exhibited a reduced rate of oxidation by 4 and 1 orders, respectively, in comparison with the base alloy. The formation of spinel structure was found to be lowered in the presence of ceria due to the reduced migration of cations from the alloy.

  17. Corrosion resistant steel

    International Nuclear Information System (INIS)

    Zubchenko, A.S.; Borisov, V.P.; Latyshev, V.B.

    1980-01-01

    Corrosion resistant steel for production of sheets and tubes containing C, Mn, Cr, Si, Fe is suggested. It is alloyed with vanadium and cerium for improving tensile properties and ductility. The steel can be melted by a conventional method in electric-arc or induction furnaces. The mentioned steel is intended to be used as a substitute for nickel-bearing austenitic steels

  18. Plasma nitriding of steels

    CERN Document Server

    Aghajani, Hossein

    2017-01-01

    This book focuses on the effect of plasma nitriding on the properties of steels. Parameters of different grades of steels are considered, such as structural and constructional steels, stainless steels and tools steels. The reader will find within the text an introduction to nitriding treatment, the basis of plasma and its roll in nitriding. The authors also address the advantages and disadvantages of plasma nitriding in comparison with other nitriding methods. .

  19. Lenguaje específico de dominio para aplicaciones de modelación glaciológica

    OpenAIRE

    Gel, Matías; Urciuolo, Adriana Beatriz; Iturraspe, Rodolfo Javier

    2014-01-01

    Las aplicaciones de software de modelado de la naturaleza se caracterizan por la complejidad propia de la información y procesos ambientales. Se requiere un nivel de abstracción adecuado y flexibilidad para la modelación de los procesos naturales. Algunas limitaciones del software del dominio provienen del uso de herramientas y lenguajes que carecen de facilidades para representar los conceptos particulares de estas aplicaciones. El Modelado específico del dominio (DSM) propone elevar el nive...

  20. Autoría de aplicaciones móviles para el análisis de datos

    OpenAIRE

    Person Montero, Tatiana

    2018-01-01

    La incorporación de aplicaciones móviles en diversos entornos genera una gran cantidad de información resultante de la interacción de los usuarios con estas aplicaciones. El análisis de esta información puede ser de gran utilidad para el profesional, ya que le puede facilitar la toma de decisiones o la valoración del proceso que esté aplicando, permitiendo mejorar los resultados o detectar determinados patrones. La información recogida se puede definir siguiendo una serie de características: ...

  1. PREPARACIÓN ELECTROQUÍMICA DE CAPAS NANOESTRUCTURADAS DE ZnO PARA APLICACIONES FOTOVOLTAICA

    OpenAIRE

    Moya Forero, Mónica Mercedes

    2012-01-01

    En esta tesis se centra en el estudio de capas delgadas basadas en óxido de zinc (ZnO) para aplicaciones fotovoltaicas, en concreto células solares sensibilizadas con colorante (DSSC). Se optimizaron los parámetros de crecimiento de estas nanoestructuras hibridas depositadas mediante la técnica de electrodeposición catódica para posteriormente desarrollar un dispositivo eficiente para la conversión de la luz. OBJETIVOS Los objetivos principales de la tesis son: - Establecer las co...

  2. ANÁLISIS COMPARATIVO DE FRAMEWORKS PARA EL DESARROLLO DE APLICACIONES WEB EN JAVA

    OpenAIRE

    Sánchez Acosta, Carlos; Universidad Señor de Sipán; Tuesta Monteza, Victor; Universidad Señor de Sipán; Mejía Cabrera, Iván

    2015-01-01

    En éste documento se presenta un análisis comparativo de frameworks en Java para el desarrollo de aplicaciones web, aplicando una matriz de un modelo de evaluación. Para analizar los frameworks y seleccionarlos se realizó en base a criterios de madurez y documentación, obteniendo como resultado los Frameworks Spring, Struts, JSF, Angular JS para su evaluación.  Asimismo para el análisis teórico de frameworks se formuló un método QSOS, concebido para definir características comparativas del so...

  3. Arquitectura de software basada en microservicios para desarrollo de aplicaciones web de la Asamblea Nacional

    OpenAIRE

    López Hinojosa, José Daniel

    2017-01-01

    Proponer una arquitectura de software basada en microservicios para el desarrollo de aplicaciones web en la Coordinación General de Tecnologías de la Información y Comunicación de la Asamblea Nacional del Ecuador. Actualmente, el proceso de desarrollo de software que realiza la Coordinación General de Tecnologías de la Información y Comunicación (CGTIC) de la Asamblea Nacional del Ecuador (ANE) constituye el empleo de una arquitectura de software tradicional o monolítica que ha sido ...

  4. Aplicaciones Nutraceúticas y cosmeceúticas de las algas

    OpenAIRE

    López-Figueroa, Félix

    2017-01-01

    El uso de la biomasa algal en diversas aplicaciones biotecnológicas ha experimentado un gran desarrollo en los últimos años. El crecimiento de las publicaciones científicas con contenidos como “extractos de algas”, “compuestos bioactivos de algas”, “biorremediación” o ”cosmética con algas” ha sido exponencial. Dentro de la Biotecnología azul se ha generado un mercado muy dinámico en el que la acuicultura, cosméticos, nutracéuticos e ingredientes funcionales tienen un gran peso. Los campos ...

  5. APLICACION DE TECNICAS DE INGENIERIA METABOLICA AL MEJORAMIENTO DE LA PRODUCCION DE TREHALOSA POR CORYNEBACTERIUM GLUTAMICUM.

    OpenAIRE

    PADILLA IGLESIAS, LEANDRO MAURICIO

    2004-01-01

    La Trehalosa es un disacárido con tremendas aplicaciones en la industria biotecnológica y alimenticia. Este compuesto se encuentra en muchos organismos, a causa de su capacidad de proteger las células contra el calor y la deshidratación. Un ejemplo, es la bacteria Gram-positiva Corynebacterium glutamicum, la cual sintetiza trehalosa a través de dos rutas principales, TreYZ y OtsBA, usando ADP-glucosa (especulativamente) y UDP-glucosa, respectivamente, como dadores de unidades de ...

  6. Sistemas operativos móviles: funcionalidades, efectividad y aplicaciones útiles en Colombia

    OpenAIRE

    2011-01-01

    Sistemas operativos móviles más utilizados actualmente con sus funcionalidades, características y descripciones generales, efectividad y análisis realizado a 2 aplicaciones de uso masivo en Colombia. La situación planteada según las investigaciones iniciales, dan a conocer que a pesar de la gran acogida que han tenido el ingreso de los sistemas operativos móviles en Colombia (que ha sido de gran impacto en el mercado mundial) los usuarios no pueden explotar al máximo sus capacidades, debido p...

  7. Aplicaciones Móviles: Mejorar la imagen corporativa de los aeropuertos y diferenciarlos ante la competencia

    OpenAIRE

    Florido-Benítez, Lázaro

    2017-01-01

    La imagen que proyectan los aeropuertos a través de sus apps afectan directa e indirectamente en la satisfacción del pasajero. Hoy día los aeropuertos compiten entre si para captar un mayor números de aerolíneas y pasajeros, con el objetivo de incrementar sus ingresos comerciales. Las aplicaciones aeroportuarias como herramienta de marketing están ofreciendo un abanico de oportunidades al binomio pasajero y aeropuerto. Si los aeropuertos quieren mejorar la experiencia del pasajero y diferenci...

  8. Biotecnologia Ambiental. Aplicacions biotecnològiques a la millora del medi ambient

    OpenAIRE

    Blanch i Gisbert, Anicet

    2010-01-01

    La biotecnología ambiental comprende el conjunto de actividades tecnológicas que facilitan la comprensión y la gestión de los sistemas biológicos en el medio ambiente, con el fin de proveer productos y servicios. Actualmente, la gestión del medio ambiente y de sus recursos naturales no se comprende si no se realiza de manera sostenible. Los avances científicos y tecnológicos le están permitiendo a la biotecnología ambiental, el desarrollo de nuevas herramientas y aplicaciones con los que resp...

  9. Aplicaciones de la tecnologia de control termico y de madurez del concreto en Colombia

    OpenAIRE

    Quimbay Herrera, Rodrigo

    2009-01-01

    La Tecnología del control térmico y de madurez del concreto (TCTM) tiene un potencial muy amplio en la industria del cemento y del concreto en Colombia, tanto por sus múltiples aplicaciones en los procesos de control de calidad en obra (instrumentación de elementos, control de probetas), como en el control de calidad de recepción en planta para la materia prima (control en tiempo real del cemento). Igualmente, en el control de producción de las diferentes mezclas (e...

  10. Aplicaciones de la inteligencia artificial en la Medicina: perspectivas y problemas

    OpenAIRE

    Expósito Gallardo, María del Carmen; Ávila Ávila, Rafael

    2008-01-01

    Los avances experimentados en el campo de la informática médica en Cuba comprenden la investigación, la docencia, la asistencia secundaria y primaria; así como la gerencia de las instituciones de salud. En este campo, las aplicaciones pertenecientes a la denominada área de la inteligencia artificial despiertan un gran interés, debido a sus posibilidades para involucrarse en situaciones donde se requiere un gran acervo de conocimientos médicos, el veloz procesamiento de los datos y la toma efe...

  11. Fortalecimiento en la seguridad de web services para aplicaciones críticas

    OpenAIRE

    Casanovas, Eduardo; Boiero, Fernando; Tapia, Carlos

    2015-01-01

    Reconociendo a las propiedades de la Seguridad de la Información (confidencialidad, integridad y disponibilidad) como elementos esenciales de cualquier transferencia de datos, haciendo foco en el conjunto de protocolos y estándares utilizados para intercambiar datos entre aplicaciones web, es decir, Web Services, para el presente trabajo definimos el objetivo general de asegurar dichas comunicaciones, teniendo en consideración que la información intercambiada es igual o más crítica y confiden...

  12. Diseño de planos indoor para aplicaciones móviles

    OpenAIRE

    Romagnoli, Nicolás

    2013-01-01

    Investigando el contexto de las aplicaciones de navegación indoor, encontramos que uno de los problemas en este dominio, es la generación de planos navegables. Este trabajo busca desarrollar una herramienta que permita la creación de planos de interiores, como así también la definición de marcadores posicionados espacialmente que permitan posteriormente brindar servicios de navegación para recorrerlo, a través de la definición de “caminos” entre el usuario y el destino seleccionado. El objeti...

  13. Sistema de autenticidad para aplicaciones de análisis de eventos para seguridad.

    OpenAIRE

    ESCAMILLA PARDO, TONI

    2017-01-01

    [ES] En este proyecto se afronta la creación de un sistema distribuido capaz de garantizar, en aplicaciones empleadas para el análisis de eventos de seguridad, la autenticidad de los datos transmitidos entre el host cliente y servidor con el fin de asegurar la integridad de los mismos en la transmisión entre ambas partes, así como evitar la posible alteración en el destino. Para ello, se utilizará la tecnología blockchain a modo de base de datos en la que se almacenen los hashe...

  14. Aplicaciones de los autómatas celulares a la generación de bits

    OpenAIRE

    Hernández Encinas, Luis; Martín del Rey, Angel; Rodríguez Sánchez, Gerardo

    2002-01-01

    Se presentan en este artículo la principales propiedades de los autómatas celulares lineales, y en particular de los llamados de Wolfram. Se definen, además, algunas nociones de criptografía con el fin de señalar las principales aplicaciones de los autómatas celulares a la misma, como la generación de números pseudoaleatorios para los cifrados en flujo o la generación de claves.

  15. Metodología de modelado de aplicaciones web móviles basada en componentes

    OpenAIRE

    Vera, Pablo Martín; Pons, Claudia; González González, Carina Soledad; Giulianelli, Daniel Alberto; Rodríguez, Rocío Andrea

    2013-01-01

    Esta línea de investigación busca crear una metodología de modelado utilizando una extensión conservativa de UML (Lenguaje Unificado de Modelado) que permita diseñar aplicaciones web móviles centrándose en el modelado de la interfaz de usuario mediante la utilización de componente configurables. El objetivo final es la generación automática del código fuente completo de la aplicación. Para lograr tal fin se extienden los diagramas de clases y componentes de UML. El diagrama de clases es exten...

  16. Aplicaciones del Caos y la Complejidad en la Cadena de Suministros del Sector Agroindustrial

    OpenAIRE

    Lara Atencia, Manuel Santiago

    2016-01-01

    La presente investigación consiste en determinar las aplicaciones existentes de las teorías del caos y las teorías de la complejidad en la cadena de suministro del sector agroindustrial colombiano. Además, tiene como propósito describir el sector de la agroindustria y la cadena de suministro, identificar los modelos de caos y complejidad y posteriormente determinar cuáles de éstos son aplicables al sector. Se define el caos como una sub-disciplina de las matemáticas que estudia sistemas compl...

  17. Potenciales singulares en sistemas cuánticos tridimensionales y aplicaciones físicas.

    OpenAIRE

    Santamaría Sanz, Lucía

    2017-01-01

    El presente trabajo pretende abordar el análisis de un problema de mecánica cuántica con interés por sus potenciales aplicaciones en física de materiales (en especial aislantes topológicos) y en física de agujeros negros. Fundamentalmente se trata de resolver la ecuación de Schrödinger (caso no relativista) en tres dimensiones espaciales (3D) para un potencial singular con simetría radial del tipo V (r) = A δ(r − r0) Interesan tanto sus estados ligados (interpretados como...

  18. Los costos de la calidad: conceptos y aplicaciones en la industria farmacéutica

    OpenAIRE

    Enrique Yacuzzi; Fernando Martín

    2003-01-01

    Este documento de trabajo es una introducción práctica al estudio de los costos de la calidad (CC). En las primeras secciones se describen algunos métodos y aplicaciones sencillas. Utilizando ejemplos de la implantación de un sistema de CC en el área de acondicionamiento de un laboratorio farmacéutico multinacional que opera en la Argentina, se presentan definiciones y cálculos de costos, con ejemplos de los informes y planillas más comunes. Se estudia la clasificación de los costos y se brin...

  19. Análisis de la calidad y seguridad de la información de aplicaciones móviles en prevención terciaria

    Directory of Open Access Journals (Sweden)

    Martínez-Moreno J

    2015-12-01

    Full Text Available Objetivo: Analizar la calidad y seguridad de la información de las aplicaciones móviles en la App Store de Apple® destinadas a prevención terciaria. Material y métodos: Estudio observacional transversal de las aplicaciones móviles más populares en la categoría de medicina disponibles en Apple Store® a día de 21 de diciembre de 2014. Las aplicaciones fueron evaluadas con los criterios establecidos en el programa AppSaludable. Se seleccionaron aquellos criterios relacionados con la evaluación de la calidad y seguridad de la información. Resultados: De las 160 aplicaciones recogidas, sólo 12 aplicaciones estaban incluidas en la prevención terciaria. Todas las aplicaciones recuperadas estaban relacionadas con la adherencia, diabetes, hipertensión y alergia. Las aplicaciones desarrolladas por equipos multidisciplinares fueron las que presentaron mayor rigor en su información, Conclusiones: La presencia de un profesional sanitario como colaborador de la aplicación parece mejorar la calidad de la información.

  20. Desarrollo de aplicaciones móviles bajo la plataforma de Iphone

    Directory of Open Access Journals (Sweden)

    Jaime Esteban Roa Castañeda

    2011-07-01

    Full Text Available El iPhone es un dispositivo móvil que lleva cerca de cinco años en el mercado de celulares, y sus funciones van más allá del uso como tal de un teléfono celular, gracias al App Store, que ofrece miles de aplicaciones creadas por desarrolladores alrededor del mundo. La arquitectura y el sistema operativo del iPhone permiten que las aplicaciones creadas por desarrolladores usen tecnologías especializadas para diferentes tipos de usuarios, permitiendo incluir características como gráficos de alta definición o usar accesorios de hardware, haciendo uso de los frameworks soportados por la arquitectura del dispositivo; todo esto es posible crearlo gracias a las herramientas de desarrollo provistas por Apple. El almacenamiento y la persistencia de datos se ven plasmados en el desarrollo de una aplicación caso de estudio que hace uso de Core Data para el manejo de la información.

  1. Desarrollo de aplicaciones móviles bajo la plataforma de Iphone

    Directory of Open Access Journals (Sweden)

    Karen Melissa Rojas Lizarazo

    2012-05-01

    Full Text Available El iPhone es un dispositivo móvil que lleva cerca de cinco años en el mercado de celulares, y sus funciones van más allá del uso como tal de un teléfono celular, gracias al App Store, que ofrece miles de aplicaciones creadas por desarrolladores alrededor del mundo. La arquitectura y el sistema operativo del iPhone permiten que las aplicaciones creadas por desarrolladores usen tecnologías especializadas para diferentes tipos de usuarios, permitiendo incluir características como gráficos de alta definición o usar accesorios de hardware, haciendo uso de los frameworks soportados por la arquitectura del dispositivo; todo esto es posible crearlo gracias a las herramientas de desarrollo provistas por Apple. El almacenamiento y la persistencia de datos se ven plasmados en el desarrollo de una aplicación caso de estudio que hace uso de Core Data para el manejo de la información.

  2. Propiedades y aplicaciones de los materiales aislantes a base de vidrio espumado

    Directory of Open Access Journals (Sweden)

    Sánchez Castro, Carlos

    1958-02-01

    Full Text Available Not availableEn un artículo precedente, aparecido en el núm. 82 de U. A. M. C., se definieron y estudiaron brevemente los materiales aislantes a base de vidrio espumado -Foamglas-, dedicándose una atención más amplia a los procedimientos y ensayos de laboratorio, realizados para obtener la máxima espumación del producto. Entonces sólo se mencionaron algunas de sus características y propiedades más importantes; también se indicaron, sin entrar en detalles, algunas de sus aplicaciones. Seguidamente, y como complemento de lo anteriormente dicho, se van a enumerar: las características de este material, pesos específicos, coeficientes de aislamiento, resistencias, etc.; los productos que con él se fabrican, bloques, planchas, coquillas, etc.; y las distintas aplicaciones que tiene en la construcción y en otras industrias, a las cuales beneficia con su colaboración, resolviendo problemas de aislamiento, aligeramiento de peso, etc. En distintas fotografías se presentan algunos ejemplos de aislamiento, de edificios, fijación de piezas y enlucido o revestimiento de los paramentos realizados con este producto.

  3. Potenciales aplicaciones de Moringa oleifera. Una revisión crítica

    Directory of Open Access Journals (Sweden)

    C Martín

    Full Text Available Moringa oleifera es un árbol originario de la India al que se le atribuyen múltiples beneficios para el bienestar humano. Es de crecimiento rápido, de relativamente poca exigencia hacia el suelo y se cultiva en toda la franja intertropical. Uno de los principales usos de sus hojas y de la torta de prensado de su semilla es en la formulación de raciones para la alimentación animal. Sin embargo, prácticamente todas las partes del árbol tienen diversas aplicaciones, sobre lo cual existen testimonios que se remontan a la Antigüedad. En este trabajo se hace una revisión de la literatura disponible sobre la utilización de esta planta. Se presentan distintos campos de aplicación de M. oleifera a la luz del creciente interés científico que ha generado en los últimos lustros. El objetivo es presentar las evidencias aportadas por la literatura científica que confirman y explican las propiedades y aplicaciones de la moringa, las cuales se distancian de versiones sin confirmar aportadas por la literatura popular y la publicidad.

  4. Application techniques of coatings by thermal projection; Tecnicas de aplicacion de recubrimientos por proyeccion termica

    Energy Technology Data Exchange (ETDEWEB)

    Porcayo Calderon, Jesus [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

    1995-12-31

    The coatings applied by thermal projection have an important number of applications in different industries (chemical, oil, electric, nuclear, etc.). The main purpose of the protection by means of coatings is to alter the surface characteristics of a component so as to resist corrosive environments, abrasion and erosion, among others. The coatings can be applied by different methods, but due to the fact that its characteristics appreciably differ from the base metal, it is important the knowledge of its properties when a coating is selected for a specific use. In this article the characteristics of the applied coatings by thermal projection, the factors that affect its performance and the principal application techniques, are described. [Espanol] Los recubrimientos aplicados por proyeccion termica tienen un numero importante de aplicaciones en diferentes industrias (quimica, petrolera, electrica, nuclear, etc.). El proposito principal de la proteccion por medio de recubrimientos es alterar las caracteristicas de la superficie de un componente de manera que resista ambientes corrosivos, abrasion y erosion, entre otros. Los recubrimientos pueden aplicarse por diferentes metodos, pero debido a que sus propiedades difieren apreciablemente de las del metal base, es importante el conocimiento de sus propiedades cuando se selecciona un recubrimiento para un uso especifico. En este articulo se describen las caracteristicas de los recubrimientos aplicados por proyeccion termica, los factores que afectan su desempeno y las principales tecnicas de aplicacion.

  5. Application techniques of coatings by thermal projection; Tecnicas de aplicacion de recubrimientos por proyeccion termica

    Energy Technology Data Exchange (ETDEWEB)

    Porcayo Calderon, Jesus [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

    1996-12-31

    The coatings applied by thermal projection have an important number of applications in different industries (chemical, oil, electric, nuclear, etc.). The main purpose of the protection by means of coatings is to alter the surface characteristics of a component so as to resist corrosive environments, abrasion and erosion, among others. The coatings can be applied by different methods, but due to the fact that its characteristics appreciably differ from the base metal, it is important the knowledge of its properties when a coating is selected for a specific use. In this article the characteristics of the applied coatings by thermal projection, the factors that affect its performance and the principal application techniques, are described. [Espanol] Los recubrimientos aplicados por proyeccion termica tienen un numero importante de aplicaciones en diferentes industrias (quimica, petrolera, electrica, nuclear, etc.). El proposito principal de la proteccion por medio de recubrimientos es alterar las caracteristicas de la superficie de un componente de manera que resista ambientes corrosivos, abrasion y erosion, entre otros. Los recubrimientos pueden aplicarse por diferentes metodos, pero debido a que sus propiedades difieren apreciablemente de las del metal base, es importante el conocimiento de sus propiedades cuando se selecciona un recubrimiento para un uso especifico. En este articulo se describen las caracteristicas de los recubrimientos aplicados por proyeccion termica, los factores que afectan su desempeno y las principales tecnicas de aplicacion.

  6. Estudio de capacidades y aplicaciones de nuevos estándares web en soluciones empresariales

    OpenAIRE

    Morales Tua, Joan Manuel

    2011-01-01

    Castellano: Este proyecto muestra un estudio de la nueva generación de estándares web conocidos como HTML5, con la finalidad de evaluar las posibilidades tecnológicas que estos ofrecen en el desarrollo de aplicaciones web corporativas, además se presenta el desarrollo de una aplicación prototipo.

  7. Aplicaciones web para móvil: Estudio y desarrollo de una plataforma web orientada a la telemedicina

    OpenAIRE

    Gutiérrez Díez, Pablo

    2013-01-01

    En el presente Trabajo Fin de Máster, se realiza un estudio y desarrollo de una plataforma web para dispositivos móviles orientada a la telemedicina, concretamente en el campo de la salud mental. Las aplicaciones mHealth (Mobile Health) se encuentran en auge y continuarán siendo un factor importante en la asistencia sanitaria, dado que ...

  8. Análisis del comportamiento contextual del usuario y su relación con el consumo de aplicaciones móviles

    OpenAIRE

    Luis Antonio Rojas-Potosí; Leandro Krug Wives; Alejandro Fernández; Juan Carlos Corrales

    2014-01-01

    El mercado de aplicaciones móviles crece aceleradamente, captando la atención sobre el análisis del consumo de las mismas para mejorar su recomendación y la satisfacción del usuario, soportado en la búsqueda de información que permita explicar la ocurrencia de eventos del ciclo de vida de las aplicaciones. En este sentido algunos estudios muestran una fuerte relación entre dichos eventos e información sobre la situación contextual actual del usuario y su registro de consumo de aplicaciones. S...

  9. Investigación en Progreso: Ingeniería de Software en el Desarrollo de Aplicaciones Sensibles al Contexto

    Directory of Open Access Journals (Sweden)

    Marisa D. Panizzi

    2015-10-01

    Full Text Available Las aplicaciones han ido evolucionando independientemente de cuál sea su dominio de aplicación, actualmente nos encontramos con aplicaciones que pueden brindar servicios de acuerdo a la ubicación, tiempo y perfil del usuario. Este tipo de aplicaciones que brindan estos servicios se las conoce como Aplicaciones Sensibles al Contexto (CA – Context Aware, en este tipo de aplicaciones predominan los dispositivos móviles y el perfil del usuario. La evolución varía en función de la forma de uso de la computadora, es decir que se brinden servicios a pedido del usuario o que se brinden servicios de manera automática. Para acompañar la evolución de este tipo de aplicaciones, la Ingeniería de Software ha focalizado sus esfuerzos en aspectos relacionados a separar la aplicación de todo lo concerniente a la captación, interpretación, control y supervisión de la información contextual. Es decir que desde el punto de vista del diseño, se separe la conducta sensible al contexto de la conducta propia de la aplicación con el propósito de que ambos tipos de aplicaciones pueden evolucionar en forma independiente además de reducir el tiempo de desarrollo en este tipo de sistemas. Este proyecto presenta una sub línea, la cual orientará sus aportes, en la consolidación de un framework de gestión contextual de dos o tres variables de contexto como por ejemplo: la ubicación, considerando la construcción de la documentación relevante que lo respalde como así también su fase de experimentación con una aplicación que permitirá a los usuarios de la comunidad universitaria UM hacer uso de los servicios ofrecidos por la misma. La segunda sub línea, se vincula al Área de la Ingeniería de Requisitos, pretendiendo obtener un modelo para la especificación de requisitos de software para sistemas sensibles al contexto.

  10. Características generales, propiedades, yacimientos y aplicaciones de pirofilita. II. Yacimientos, aplicaciones y utilización como materia prima cerámica

    Directory of Open Access Journals (Sweden)

    Sánchez Soto, P. J.

    1998-10-01

    Full Text Available In this work, the main world deposits of pyrophyllite are indicated according to the literature, showing the available production data. It is emphasized the research focusing on mining and characterization of raw materials containing pyrophyllite, which shows a marked applied interest. It is described and reviewed the most relevant applications of pyrophyllite and pyrophyllite raw materials, in especial refractories and ceramics, fillers, building materials, catalysts and as a high-pressure medium for synthesis of materials. Finally, it is also described and reviewed its use as raw material for the preparation of advanced materials, such as sialon, emphasizing the possibilities of application of pyrophyllite raw materials in our country as a result of distinct investigations of relevant interest performed by several Research Institutes and University Departments. It is deduced that pyrophyllite and pyrophyllite raw materials are increasing in relative importance in many applied fields, as compared with other layer silicates, such as talc and kaolinite.

    En este trabajo se indican los principales yacimientos mundiales de pirofilita según la bibliografía, los datos de producción disponibles, además de revisar las investigaciones más destacadas sobre prospección y caracterización de materias primas que contienen pirofilita y que presentan un marcado interés aplicado. Se realiza una amplia revisión de las principales aplicaciones a las que se destinan dichas materias primas, en especial para la preparación de materiales cerámicos y refractarios, su uso como carga, en la construcción, obtención de catalizadores y síntesis de materiales a alta presión debido a sus propiedades. Por último, se describen y revisan sus aplicaciones en la preparación de nuevos materiales y materiales avanzados, como son los sialones, destacando su potencial de utilización en nuestro país como resultado de diversas investigaciones de inter

  11. Methods of forging steel

    OpenAIRE

    Pečoler, Primož

    2014-01-01

    The following work presents processes of steel forming, challenges when forging steel, forming machines suitable for forging and which choice of machine is most suitable for forging. We can separate steel forming to free forging and drop forging. Free forging can be divided to hand forging and machine forging. The correct choice of furnaces is also very important. We must reach correct temperature in the furnace for raw steel to melt with less scalings. In diploma I mentioned some machine...

  12. Prospects of structural steels

    International Nuclear Information System (INIS)

    Bannykh, O.A.

    2012-01-01

    The current state of world steel production is considered as well as the development strategy of metallurgy industry in the Russian Federation through to 2020. The main factors determining the conservation of steel as perspective material for industry are given: energy expenses on production, the well-proven recirculation technology, the capability of changing steel properties in wide range, temperature range of operation. The conclusion is made that in the immediate future steel will not lose its importance [ru

  13. Influence of rare earth oxides in the oxidation of chromia forming alloys

    International Nuclear Information System (INIS)

    Ramanathan, L.V.

    1989-01-01

    The influence of superficial application of rare earth oxides such as CeO sub(2), La sub(2)O sub(3), Nd sub(2)O sub(3), Sm sub(2)O sub(3), and Gd sub(2)O sub (3) to AISI 304 and 310 stainless steels, on their isothermal oxidation behavior at 900 sup(0) and 1000 sup(0)C, and cyclic oxidation behavior between 20 sup(0) and 1000 sup(0)C has been studied. The application of rare earth oxides (REO) has been found to increase the oxidation resistance at AISI 304. No significant improvements in oxidation resistance of AISI 310 were noted. The oxidation resistance of AISI 304 was highest in the presence of CeO sub(2) on its surface. The other REO in decreasing order of influence on oxidation resistance are La sub(2)O sub(3), Nd sub(2)O sub(3), Sm sub(2)O sub(3) and Gd sub(2)O sub(3). SEM investigations of the oxide scale morphology revealed that the improved resistance is probably due to the formation of a thin layer of fine grained compact Cr sub(2)O sub(3) and the higher adhesion of the scale to its increased plasticity. (author)

  14. Trends in steel technology

    International Nuclear Information System (INIS)

    Anon.

    1980-01-01

    Dual phase steels, composite products, and microalloyed steels are making inroads in the automotive industry applications for bumpers, automotive parts, bodies, mechanical parts, suspension and steering equipment and truck bumpers. New steels are also used to support solar mirrors and cells, in corrosive environments in the oil and gas industry, fusion reactors, and pressure vessels in nuclear power plants

  15. Desenvolupament d'aplicacions web en Django sobre servidor apache, gestionades amb mòdul WSGI i relacionades amb base de dades Postgresql

    OpenAIRE

    Bosch Gascón, Carlos

    2013-01-01

    Desenvolupament d'aplicacions web en Django per al Segon Concurs de fotografia matemàtica FotoMath 2011. Allotjades en servidor Apachez, gestionades amb mòdul wsgi i relacionades amb una base de dades postgresql.

  16. APRENDIZAJE BASADO EN EJEMPLOS: DESARROLLO DE APLICACIONES EMPRESARIALES CON TECNOLOGÍAS .NET

    Directory of Open Access Journals (Sweden)

    Marcos Gestal

    2015-06-01

    Full Text Available RESUMEN: El framework J2EE ha sido el gran dominador, durante mucho tiempo, en el desarrollo de aplicaciones empresariales. Esto hecho originó la aparición de un rico ecosistema de herramientas, manuales, tutoriales, etc., que explican las diferentes alternativas o peculiaridades a la hora de su implementación. La irrupción de .NET Framework, en el ámbito empresarial, ha producido una fuerte demanda de implementación de aplicaciones bajo dicha arquitectura. Sin embargo, la cantidad o calidad de la documentación disponible dista considerablemente con respecto a la existente, su principal alternativa (J2EE. Esta laguna de documentación, es especialmente visible y preocupante cuando se establece como objetivo dar a conocer los conceptos del framework, desde un punto de vista docente, a los futuros egresados del Grado en Ingeniería en Informática. Este trabajo describe el enfoque docente seguido, para alcanzar el citado objetivo de familiarizar a los alumnos con este framework alternativo y las prácticas habituales de modelo dentro de éste. Para ello, se basa principalmente de un conjunto de sencillos tutoriales con los que mostrar los fundamentos de la tecnología y dos aplicaciones completas (miniportal y minibank en las que se muestra cómo aplicar patrones de diseño, a la hora de abordar una aplicación empresarial. ABSTRACT: For a long time, J2EE has been the dominating framework for the development of business applications. This fact resulted in a rich ecosystem of tools, manuals, tutorials, etc. that explain different implementation alternatives or peculiarities. The incursion of .NET Framework in the business environment has generated a strong demand of application implementation under this architecture. However, the quantity and quality of documents available significantly differs from its main alternative (J2EE. This documentation gap is especially visible and worrying when the objective is to teach the concepts of Framework

  17. Banco de ensayos para materiales piezoeléctricos en aplicaciones viales

    Directory of Open Access Journals (Sweden)

    de Frutos, J.

    2011-04-01

    Full Text Available The test bench system described in this paper performs experiments on piezoelectric materials used in road traffic applications, covering a range between 14 and 170 km/h, which is considered enough for testing under standard traffic conditions. A software has been developed to control the three phase induction motor driver and to acquire all the measurement data of the piezoelectric materials. The mass over each system’s axis can be selected, with a limit of 60 kg over each wheel. The test bench is used to simulate the real behaviour of buried piezoelectric cables in road traffic applications for both light and heavy vehicles. This new test bed system is a powerful research tool and can be applied to determine the optimal installation and configuration of the piezoelectric cable sensors and opens a new field of research: the study of energy harvesting techniques based on piezoelectric materials.

    En este trabajo se define y propone un banco de ensayos que permite testar materiales piezoeléctricos para aplicaciones viales en sus diferentes configuraciones en un rango de velocidad entre los 14 y los 170 km/h, lo que cubre sobradamente las condiciones de tráfico real. Tanto el control del variador de velocidad del motor trifásico que realiza el accionamiento del banco, como la recogida de resultados de medida en las pruebas de excitación y de fatiga de los compuestos piezoeléctricos, se realiza de forma automatizada mediante código informatico. El peso que soporta cada eje del banco es configurable, permitiendo reproducir las señales obtenidas en aplicaciones donde los materiales piezoeléctricos actúan de sensores enterrados en la calzada para vehículos tanto pesados como ligeros. Gracias a esta nueva herramienta se facilita la investigación con materiales de este tipo en aplicaciones viales optimizando tanto el tipo como la disposición e instalación de los mismos, además de abrir el camino a la novedosa investigación sobre

  18. Un modelo de coordinación cliente-servidor, de apoyo a la construcción de aplicaciones colaborativas portables

    OpenAIRE

    Ochoa, Sergio; Fuller, David A.

    2001-01-01

    En la actualidad existe una gran variedad de plataformas de apoyo al desarrollo de aplicaciones colaborativas, que trabajan bajo una arquitectura cliente-servidor [Chabert 98, Guerrero 98, Licea 98, Trevor 97]. Estas poseen un alto grado de incompatibilidad entre ellas, lo cual produce una fuerte dependencia de la aplicación cliente, hacia el servidor usado. Debido a esto, las capacidades de las aplicaciones están sometidas a la funcionalidad permitida por el servidor. Esto entorpece el avanc...

  19. Weldability of Stainless Steels

    International Nuclear Information System (INIS)

    Saida, Kazuyoshi

    2010-01-01

    It gives an outline of metallographic properties of welding zone of stainless steels, generation and mechanisms of welding crack and decreasing of corrosion resistance of welding zone. It consists of seven chapters such as introduction, some kinds of stainless steels and properties, metallographic properties of welding zone, weld crack, toughness of welding zone, corrosion resistance and summary. The solidification modes of stainless steels, each solidification mode on the cross section of Fe-Cr-Ni alloy phase diagram, each solidification mode of weld stainless steels metal by electron beam welding, segregation state of alloy elements at each solidification mode, Schaeffler diagram, Delong diagram, effects of (P + S) mass content in % and Cr/Ni equivalent on solidification cracking of weld stainless steels metal, solidification crack susceptibility of weld high purity stainless steels metal, effects of trace impurity elements on solidification crack susceptibility of weld high purity stainless steels metal, ductile fracture susceptibility of weld austenitic stainless steels metal, effects of H2 and ferrite content on generation of crack of weld 25Cr-5N duplex stainless steels, effects of O and N content on toughness of weld SUS 447J1 metals, effect of ferrite content on aging toughness of weld austenitic stainless steel metal, corrosion morphology of welding zone of stainless steels, generation mechanism of knife line attack phenomenon, and corrosion potential of some kinds of metals in seawater at room temperature are illustrated. (S.Y.)

  20. The steel scrap age.

    Science.gov (United States)

    Pauliuk, Stefan; Milford, Rachel L; Müller, Daniel B; Allwood, Julian M

    2013-04-02

    Steel production accounts for 25% of industrial carbon emissions. Long-term forecasts of steel demand and scrap supply are needed to develop strategies for how the steel industry could respond to industrialization and urbanization in the developing world while simultaneously reducing its environmental impact, and in particular, its carbon footprint. We developed a dynamic stock model to estimate future final demand for steel and the available scrap for 10 world regions. Based on evidence from developed countries, we assumed that per capita in-use stocks will saturate eventually. We determined the response of the entire steel cycle to stock saturation, in particular the future split between primary and secondary steel production. During the 21st century, steel demand may peak in the developed world, China, the Middle East, Latin America, and India. As China completes its industrialization, global primary steel production may peak between 2020 and 2030 and decline thereafter. We developed a capacity model to show how extensive trade of finished steel could prolong the lifetime of the Chinese steelmaking assets. Secondary steel production will more than double by 2050, and it may surpass primary production between 2050 and 2060: the late 21st century can become the steel scrap age.

  1. Kinetic of martensitic transformations induced by hydrogen in the austenite

    International Nuclear Information System (INIS)

    Oliveira, Sergio P. de; Saavedra, A.; Miranda, P.E.V. de

    1986-01-01

    The X-ray diffractometry technique was used, with an automatic data acquisition system to determine the kinetics of hydrogen induced martensitic phase transformations in an AISI 304 austenitic stainless steel type, used in nuclear power plants. Hydrogenation was performed cathodically in a 1N sulfuric acid solution, containing 100 mg/l of arsenic trioxide, at 50 0 C, during 2 hours and with a current density of 200 A/m 2 . It was found that the microstructure of the steel plays a role on the generation of hydrogen induced martensitic phases and surface micro cracks. Both kinetics were slower on a pre-cold rolled steel. (Author) [pt

  2. Exploración de viabilidad sobre ideas de aplicaciones en el mercado colombiano

    OpenAIRE

    Tarazona Ocampo, Andrés Felipe; Soto Florez, María Paz; Camacho Cala, Paula Vanessa

    2016-01-01

    La economía mundial cambia a un ritmo vertiginoso y exponencial gracias a la rápida transformación de la tecnología. Diferentes dinámicas como el crecimiento en cobertura del internet; la creciente facilidad de obtención de una tarjeta de crédito; la popularización del uso de smartphones; y el crecimiento en uso del comercio electrónico; han dado cabida a la aparición de nuevos tipos de negocio, como el de servicios electrónicos y aplicaciones, que hace algunas décadas atrás eran inviables. ...

  3. Modelo de Sistema Basado en Conocimiento en el Dominio de la Seguridad de Aplicaciones

    Directory of Open Access Journals (Sweden)

    María Victoria Bajarlía

    2013-12-01

    Full Text Available El objetivo es proponer un modelo de un sistema basado en conocimiento (SBC aplicado al análisis de seguridad de aplicaciones de gestión. El modelo se fundamenta en un sistema basado en conocimiento (SBC que cuenta con un componente cognitivo que le permite incorporar conocimiento. En virtud de que las amenazas y los ataques informáticos representan un problema constante y creciente se puede suponer que el SBC, a través del aprendizaje dinámico que lo mantendrá actualizado, podrá asistir a los especialistas en Seguridad de la Información, en el área de competencia, a la elaboración de Especificación de Requerimientos.

  4. Ecarga y la estrategia de marketing digital para aplicaciones móviles

    OpenAIRE

    Hervella Baturone, Beatriz

    2013-01-01

    RESUMEN: Ecarga y la estrategia de marketing digital para aplicaciones móviles es un proyecto que trata de recoger cuáles son las principales aspectos que se deben tener en cuenta a la hora de promocionar una aplicación móvil. El trabajo consta de una primera parte, de contenido más teórico, que trata el contexto actual del mercado móvil y una segunda parte, de contenido más práctico, que consta de la descripción y documentación real de la estrategia de promoción seguida por la aplicación móv...

  5. CRITERIOS PARA LA EVALUACIÓN DE SUPERFICIES MULTITÁCTILES Y SUS APLICACIONES

    Directory of Open Access Journals (Sweden)

    YENNY A. MÉNDEZ

    2012-06-01

    Full Text Available Las superficies multitáctiles son tecnologías que empiezan a tener un elevado uso. Se toman como referentes aspectos utilizados para la evaluación de usabilidad de sistemas interactivos, así como las característicasque los investigadores y desarrolladores sugieren que deberían tener las superficies multitáctiles y las aplicaciones desarrolladas. Se presenta una propuesta inicial de criterios que deberían tenerse en cuenta para incluir  aspectos de ergonomía, usabilidad y colaboración en el momento de realizar evaluaciones para estas tecnologías. Se ilustra cómo se pueden aplicar los criterios propuestos a través de un caso de estudio que cuenta con resultados promisorios.

  6. Interactive applications for energy saving; Aplicaciones interactivas para ahorro de energia

    Energy Technology Data Exchange (ETDEWEB)

    Adame Gonzalez, Alejandro; Ramirez Anaya, Cesar; Gutierrez, Hector; Dominguez Ojeda, Xerxes; Aguilar Galvan, Alfredo [Ingenieria Energetica Integral S. A. de C. V., Mexico, D. F. (Mexico)

    1998-12-31

    A series of ideas are presented that can help in the development of interactive applications for energy saving. Emphasis is made on the Fideicomiso de Apoyo al Programa de Ahorro de Energia (FIDE)`s Interactive Course on Demand Management and Power Factor Compensation, in order to demonstrate how far one can go with the multimedia development. [Espanol] Se presenta un conjunto de ideas que pueden auxiliar en la elaboracion de aplicaciones interactivas para ahorro de energia. Se hace principal enfasis sobre el curso interactivo Administracion de la Demanda y Compensacion del Factor de Potencia del Fideicomiso de Apoyo al Programa de Ahorro de Energia (FIDE) con la finalidad de mostrar hasta donde puede llegarse con un desarrollo multimedia.

  7. Interactive applications for energy saving; Aplicaciones interactivas para ahorro de energia

    Energy Technology Data Exchange (ETDEWEB)

    Adame Gonzalez, Alejandro; Ramirez Anaya, Cesar; Gutierrez, Hector; Dominguez Ojeda, Xerxes; Aguilar Galvan, Alfredo [Ingenieria Energetica Integral S. A. de C. V., Mexico, D. F. (Mexico)

    1999-12-31

    A series of ideas are presented that can help in the development of interactive applications for energy saving. Emphasis is made on the Fideicomiso de Apoyo al Programa de Ahorro de Energia (FIDE)`s Interactive Course on Demand Management and Power Factor Compensation, in order to demonstrate how far one can go with the multimedia development. [Espanol] Se presenta un conjunto de ideas que pueden auxiliar en la elaboracion de aplicaciones interactivas para ahorro de energia. Se hace principal enfasis sobre el curso interactivo Administracion de la Demanda y Compensacion del Factor de Potencia del Fideicomiso de Apoyo al Programa de Ahorro de Energia (FIDE) con la finalidad de mostrar hasta donde puede llegarse con un desarrollo multimedia.

  8. Formação de biofilme em aço inoxidável por Aeromonas hydrophila e Staphylococcus aureus usando leite e diferentes condições de cultivo Biofilm formation by Aeromonas hydrophila and Staphylococcus aureus on stainless steel using milk and different conditions of cultivation

    Directory of Open Access Journals (Sweden)

    Cleube Andrade Boari

    2009-12-01

    Full Text Available O objetivo desta pesquisa consistiu em avaliar a formação de biofilme em aço inoxidável por Aeromonas hydrophila e Staphylococcus aureus usando leite e diferentes condições de cultivo. As variáveis em estudo consistem no cultivo monoespécie e combinado, dos referidos microrganismos e nas temperaturas de 4, 7 e 18 °C. Recipientes contendo 1000 mL de leite, densidade populacional de 10(5 UFC.mL-1 de cada microrganismo e 10 cupons de aço inoxidável (10 × 20 mm foram lacrados e armazenados, sob agitação de 60 rpm, por um período de 10 dias. As análises ocorreram a cada 48 horas. Células sésseis de A.hydrophila e S. aureus foram enumeradas através do plaqueamento seletivo em ágar m-Aeromonas selective e Baird-Parker, respectivamente. Estudos sobre o tempo de geração, enumeração de células planctônicas e observação dos cupons através da microscopia eletrônica de varredura foram conduzidos. S. aureus, em monocultivo, formou biofilme a 18 °C e a 7 °C. Para 4 °C, foi observado um processo de adesão. A presença de A. hydrophila reduziu o desempenho de S. aureus. Nesta condição de cultivo multiespécie houve formação de biofilme a 18 °C. A. hydrophila, tanto em monocultivo quanto em presença de S. aureus, formou biofilme em todas as condições pesquisadas.The aim of this research was to verify the capability of biofilm formation on stainless steel by Aeromonas hydrophila and Staphylococcus aureus using milk and different conditions of cultivation. The variables consisted in mono and multi-species cultivation of these microorganisms and in the temperatures of 4, 7 and 18 °C. Containers containing 1000 mL of milk, population density of 10(5 CFU.mL-1 of each microorganism, and ten suspended chips of stainless steel AISI 304 (10 × 20 mm were used to seal up and storage, under 60 rpm of agitation for 10 days. The analyses were conducted every 48 hours. Sessile cells of A. hydrophila and S. aureus and were enumerated

  9. Application of frequency converters in industry; Aplicacion de convertidores de frecuencia en la industria

    Energy Technology Data Exchange (ETDEWEB)

    Delmar Saavedra, Alejandro [Eficiencia Energetica, S.A. de C.V., Mexico, D. F. (Mexico)

    1999-07-01

    Next an analysis methodology for the application of a frequency converter in equipment that handles flows, as they can be pumps, fans, blowers and extractors is presented. Measurements of some practical cases that we have had in the industry are shown. Some of the types of applications in which the control of speed with the frequency converter is used, are the following ones: pumps, fans, mills, crushing machines, extruders, Banbury mixers, spinning machines, conveyors, mixers, electrical vehicles, lime furnaces, injection machines, blowers and extractors. The purpose of a frequency converter is of controlling the speed and/or torque of an electrical motor. The reasons for which a frequency converter is used can be classified, in two large fields: the necessary and those that provide energy saving. [Spanish] A continuacion se presenta una metodologia de analisis para la aplicacion de un convertidor de frecuencia en equipos que manejan flujos, como pueden ser bombas, ventiladores, sopladores y extractores. Se muestran mediciones de algunos casos practicos que hemos tenido en la industria. Algunos de los tipos de aplicaciones en donde se usa el control de velocidad con el convertidor de frecuencia, son los siguientes: bombas, ventiladores, molinos, trituradoras, extrusoras, mezcladoras banbury, maquinas de hilado, transportadoras, mezcladoras, vehiculos electricos, horno de cal, maquinas de inyeccion, sopladores y extractores. El proposito de un convertidor de frecuencia es el de controlar la velocidad y/o par en un motor electrico. Se pueden, clasificar las razones por las que se usa un convertidor de frecuencia, en dos grandes campos: las necesarias y las que proporcionan ahorros de energia.

  10. Desarrollo de un modelo matemático de diferencias finitas para el análisis del campo de temperaturas en la soldadura por arco de chapas finas de acero inoxidable

    Directory of Open Access Journals (Sweden)

    Miguel, V.

    2010-12-01

    Full Text Available This work develops a finite difference method to evaluate the temperature field in the heat affected zone in butt welding applied to AISI 304 stainless steel thin sheet by GTAWprocess. A computer program has been developed and implemented by Visual Basic for Applications (VBA in MS-Excel spreadsheet. The results that are obtained using the numerical application foresee the thermal behaviour of arc welding processes. An experimental methodology has been developed to validate the mathematical model that allows to measure the temperature in several points close to the weld bead. The methodology is applied to a stainless steel sheet with a thickness lower than 3 mm, although may be used for other steels and welding processes as MIG/MAG and SMAW. The data which has been obtained from the experimental procedure have been used to validate the results that have been calculated by the finite differences numerical method. The mathematical model adjustment has been carried out taking into account the experimental results. The differences found between the experimental and theoretical approaches are due to the convection and radiation heat losses, which have not been considered in the simulation model.With this simple model, the designer will be able to calculate the thermal cycles that take place in the process as well as to predict the temperature field in the proximity of the weld bead.

    En este trabajo se desarrolla un método de diferencias finitas para calcular el campo de temperaturas en la zona afectada por el calor en la soldadura de dos chapas de acero inoxidable AISI 304, soldadas mediante el procedimiento GTAW. Se ha desarrollado un programa informático implementado en libros de cálculo MS-Excel con Visual Basic para Aplicaciones (VBA. Los experimentos modelizados a través de la aplicación numérica predicen el comportamiento térmico de un procedimiento de soldadura. Para la validación del modelo matemático se ha desarrollado un

  11. EL COMPROMISO EN LA TEORÍA DE LA VALORACIÓN: CONCEPTOS Y APLICACIONES PEDAGÓGICAS

    Directory of Open Access Journals (Sweden)

    Jesús David Guerra Lyons

    2017-01-01

    Full Text Available El presente artículo revisa el concepto de compromiso desde la Teoría de la Valoración propuesta por Martin y White y de algunas de sus aplicaciones pedagógicas. Desde la perspectiva bajtiniana de dialogismo, Martin y White definen el compromiso como el conjunto de recursos mediante los cuales los usuarios del lenguaje entran en diálogo con las múltiples voces que inevitablemente permean sus textos, aceptándolas, rebatiéndolas, retomándolas o distanciándose de ellas. El compromiso se divide en dos tipos: monoglosia y heteroglosia. Este último se desagrega en varias subcategorías, que son definidas e ilustradas con ejemplos tomados del corpus del español de Davies. Consideramos algunas aplicaciones pedagógicas del concepto de compromiso mediante la revisión de estudios desarrollados principalmente en el contexto latinoamericano.

  12. Las aplicaciones interactivas multimedia en España: ¿hacia dónde evoluciona el mercado?

    Directory of Open Access Journals (Sweden)

    Lic. Nati Ramajo Hernández

    1998-01-01

    Full Text Available El despegue del sector multimedia en nuestro país (entendiendo como tal las aplicaciones interactivas multimedia ha sido espectacular en los últimos tiempos. El número de títulos publicados en CD-ROM, al igual que el número de productores, ha aumentado considerablemente. Pero, ¿cómo es esa nueva industria?, ¿qué productos ofrece?, ¿hacia dónde evoluciona el mercado? El presente trabajo pretende hacer un repaso a la breve historia de las aplicaciones interactivas multimedia en España hasta llegar al momento actual, analizando por el camino la tipología de los productos y concluyendo con los nuevos formatos que están cambiando el mercado.

  13. Análisis de eficiencia en arquitecturas multiprocesador para aplicaciones de transmisión y procesamiento de datos

    OpenAIRE

    Osio, Jorge R.; Salvatore, Juan Eduardo; Kunysz, Eduardo; Guarepi, V. L.; Morales, Daniel Martín

    2016-01-01

    Los principales lineamientos de investigación de este proyecto se orientan a las Arquitecturas que posibilitan el procesamiento paralelo, principalmente en sistemas multi-core. Por otro lado, la optimización de estos sistemas se orienta a determinadas aplicaciones de telemedicina y de sistemas ópticos basados en MIOC , (Multifunction Integrated Optical Chip), que requieren procesamiento y transmisión de datos de forma remota. Paralelamente a estos lineamientos el proyecto contempla el e...

  14. Formación de usuarios de la información mediante aplicaciones Web 2.0

    Directory of Open Access Journals (Sweden)

    Eder Ávila Barrientos

    2015-04-01

    Full Text Available Objetivo: Analizar las aplicaciones web 2.0 para estimar su utilización en los programas de formación de usuarios de la información. Método: Análisis documental y la hermenéutica del discurso aplicados a los documentos impresos y digitales que abordan la temática del objeto de estudio. Resultados: se responden una serie de cuestionamientos relacionados con la integración de las aplicaciones Web 2.0 en el diseño de programas de formación de usuarios de la información. En lo que respecta a la selección de aplicaciones web 2.0, se empleo la técnica de análisis de atributos basada en las variables de uso didáctico. Concluisones: Las tecnologías de la web 2.0 y su integración en los programas de formación de usuarios de la información, representan un nicho de oportunidad para los bibliotecólogos. Una oportunidad para alcanzar el futuro y romper viejos paradigmas de la formación de usurios.

  15. DESCRIPCIÓN DE UN FRAMEWORK METODOLOGICO PARA EL DESARROLLO DE APLICACIONES RELACIONADAS CON EL PATRIMONIO CULTURAL

    Directory of Open Access Journals (Sweden)

    Edwin Mauricio Hincapié-Montoya

    2014-01-01

    Full Text Available Preservar los espacios y difundirlos es una función social que debe mantener unidos a los pueblos y que no puede dejarse a un lado por el clamor y la voz del desarrollo. Para ello la tecnología juega un papel de facilitador mediático a través de la cual se puede llegar a diferentes espacios y lugares históricamente importantes pero físicamente inaccesibles por su desaparición. En los últimos años se han desarrollado aplicaciones que buscan reactivar el patrimonio cultural y hacen uso de tecnologías como realidad virtual, realidad aumentada o juegos serios. Sin embargo, la mayoría son casos de estudio en un tema particular y el área carece de un framework metodológico, que guie y facilite el desarrollo de este tipo de aplicaciones. En este articulo proponemos un framework metodológico conceptual, el cual busca guiar el desarrollo de aplicaciones relacionadas con la reactivación del patrimonio cultural al tiempo que maximiza el aprendizaje de los usuarios en este tema.

  16. Steel: Price and Policy Issues

    National Research Council Canada - National Science Library

    Cooney, Stephen

    2006-01-01

    Steel prices remain at historically elevated levels. The rapid growth of steel production and demand in China is widely considered as a major cause of the increases in both steel prices and the prices of steelmaking inputs...

  17. Microencapsulación con alginato en alimentos. Técnicas y aplicaciones

    Directory of Open Access Journals (Sweden)

    Bryshila Lupo Pasin

    2012-01-01

    Full Text Available El objetivo de este trabajo fue realizar una revisión de las técnicas de microencapsulación con alginato para aplicaciones en alimentos. El alginato ha sido uno de los polímeros más empleado en la microencapsulación, este forma una matriz altamente versátil, biocompatible y no tóxica para la protección de componentes activos, células o microorganismos sensibles al calor, pH, oxígeno y luz, entre otros factores, a los que son expuestos los alimentos durante el procesamiento y almacenaje. El proceso de microencapsulación con alginato se lleva a cabo a través de dos mecanismos de gelificación iónica: la gelificación externa y la gelificación interna, dependiendo de si el calcio se suministra desde fuera de las cápsulas o en el interior de las mismas. Para la preparación de microcápsulas de alginato de calcio con aplicaciones alimentarias, se tienen las técnicas por extrusión, en emulsión y secado por atomización. Aunque el secado por atomización ha sido para la industria un proceso práctico y económico, su aplicación con alginato se ha visto limitada por la viscosidad y velocidad de gelificación. Por el contrario, la técnica por extrusión ha sido la técnica tradicional empleada en las últimas décadas, debido a la uniformidad de las microcápsulas en su forma y tamaño. En este sentido, la técnica en emulsión es la aplicada más recientemente, la cual ha demostrado ser sencilla y de producción a gran escala. En la actualidad se desarrollan nuevas tecnologías a fin de disminuir el tamaño de las microcápsulas para así ampliar sus usos en la industria. Entre las últimas tendencias de microencapsulación, se estudian sistemas mixtos de matrices poliméricas con la finalidad de obtener propiedades físico-químicas combinadas, permitiendo hacer el proceso de encapsulación más eficiente tanto para la protección como para la liberación controlada del principio activo.

  18. Microencapsulación con alginato en alimentos. Técnicas y aplicaciones

    Directory of Open Access Journals (Sweden)

    Bryshila Lupo Pasin

    2012-06-01

    Full Text Available El objetivo de este trabajo fue realizar una revisión de las técnicas de microencapsulación con alginato para aplicaciones en alimentos. El alginato ha sido uno de los polímeros más empleado en la microencapsulación, este forma una matriz altamente versátil, biocompatible y no tóxica para la protección de componentes activos, células o microorganismos sensibles al calor, pH, oxígeno y luz, entre otros factores, a los que son expuestos los alimentos durante el procesamiento y almacenaje. El proceso de microencapsulación con alginato se lleva a cabo a través de dos mecanismos de gelificación iónica: la gelificación externa y la gelificación interna, dependiendo de si el calcio se suministra desde fuera de las cápsulas o en el interior de las mismas. Para la preparación de microcápsulas de alginato de calcio con aplicaciones alimentarias, se tienen las técnicas por extrusión, en emulsión y secado por atomización. Aunque el secado por atomización ha sido para la industria un proceso práctico y económico, su aplicación con alginato se ha visto limitada por la viscosidad y velocidad de gelificación. Por el contrario, la técnica por extrusión ha sido la técnica tradicional empleada en las últimas décadas, debido a la uniformidad de las microcápsulas en su forma y tamaño. En este sentido, la técnica en emulsión es la aplicada más recientemente, la cual ha demostrado ser sencilla y de producción a gran escala. En la actualidad se desarrollan nuevas tecnologías a fin de disminuir el tamaño de las microcápsulas para así ampliar sus usos en la industria. Entre las últimas tendencias de microencapsulación, se estudian sistemas mixtos de matrices poliméricas con la finalidad de obtener propiedades físico-químicas combinadas, permitiendo hacer el proceso de encapsulación más eficiente tanto para la protección como para la liberación controlada del principio activo.

  19. El potencial de las aplicaciones educativas en el proceso de evaluación formativa

    Directory of Open Access Journals (Sweden)

    Mayara Lustosa de Oliveira

    2017-07-01

    Full Text Available El debate sobre los objetivos reales de la evaluación no es nuevo. Sin embargo, todavía predominan aspectos como la excesiva valoración de la memoria, lo que refleja una visión tradicional y limitada. Es necesario superar el uso exclusivo de la evaluación tradicional con el fin de adoptar una evaluación formativa, modalidad que busca identificar las fallas y necesidades de los estudiantes durante el proceso educativo con el fin de recibir retroalimentación para tomar las medidas necesarias que permitan mejorar la enseñanza y el aprendizaje. Siguiendo esta necesidad, y buscando ayudar a los profesores en la aplicación de una evaluación formativa, algunos recursos tecnológicos han sido desarrollados. El presente trabajo tiene como objetivo describir el potencial de tres aplicaciones (Armet, The Cell y 3DClass en el proceso de evaluación formativa usando las bases de datos asociadas a cada aplicación. Los resultados muestran que estas aplicaciones proporcionan métricas de evaluación más transparentes, coherentes y que permiten al profesor sistematizar criterios e indicadores, lo que reduce la subjetividad del proceso de evaluación formativa y el tiempo necesario para la preparación, tabulación y análisis de datos. Gracias a que con esta tecnología es posible verificar en tiempo real el número de errores totales y por pregunta preguntas con el mayor número de errores recurrentes, preguntas con el mayor y menor índice de aciertos y el tiempo que los alumnos emplean para desarrollar la actividad, es posible determinar el progreso de los alumnos a lo largo del tiempo e identificar puntualmente dónde ocurren los errores; esto permite una investigación minuciosa sobre sus posibles causas. Esta información facilita la retroalimentación para los alumnos, ya sea como intervenciones puntuales o direccionadas por parte del profesor.

  20. The reactor vessel steels

    International Nuclear Information System (INIS)

    Bilous, W.; Hajewska, E.; Szteke, W.; Przyborska, M.; Wasiak, J.; Wieczorkowski, M.

    2005-01-01

    In the paper the fundamental steels using in the construction of pressure vessel water reactor are discussed. The properties of these steels as well as the influence of neutron irradiation on its degradation in the time of exploitation are also done. (authors)