Satellite Power System (SPS) societal assessment

Energy Technology Data Exchange (ETDEWEB)

1980-12-01

Construction and operation of a 60-unit (300 GW) domestic SPS over the period 2000 to 2030 would stress many segments of US society. A significant commitment of resources (land, energy, materials) would be required, and a substantial proportion of them would have to be committed prior to the production of any SPS electricity. Estimated resource demands, however, seem to be within US capabilities. Modifications will be required of institutions called upon to deal with SPS. These include financial, managerial and regulatory entities and, most particularly, the utility industry. Again, the required changes, while certainly profound, seem to be well within the realm of possibility. Enhanced cooperation in international affairs will be necessary to accommodate development and operation of the SPS. To remove its potential as a military threat and to reduce its vulnerability, either the SPS itself must become an international enterprise, or it must be subject to unrestricted international inspection. How either of these objectives could, in fact, be achieved, or which is preferable, remains unclear. Forty-four concerns about the SPS were identified via a public outreach experiment involving 9000 individuals from three special interest organizations. The concerns focused on environmental impacts (particularly the effects of microwave radiation) and the centralizing tendency of the SPS on society. The interim results of the public outreach experiment influenced the scope and direction of the CDEP; the final results will be instrumental in defining further societal assessment efforts.

Satellite power system (SPS) public outreach experiment

Energy Technology Data Exchange (ETDEWEB)

McNeal, S.R.

1980-12-01

To improve the results of the Satellite Power System (SPS) Concept Development and Evaluation Program, an outreach experiment was conducted. Three public interest groups participated: the L-5 Society (L-5), Citizen's Energy Project (CEP), and the Forum for the Advancement of Students in Science and Technology (FASST). Each group disseminated summary information about SPS to approximately 3000 constituents with a request for feedback on the SPS concept. The objectives of the outreach were to (1) determine the areas of major concern relative to the SPS concept, and (2) gain experience with an outreach process for use in future public involvement. Due to the combined efforts of all three groups, 9200 individuals/organizations received information about the SPS concept. Over 1500 receipients of this information provided feedback. The response to the outreach effort was positive for all three groups, suggesting that the effort extended by the SPS Project Division to encourage an information exchange with the public was well received. The general response to the SPS differed with each group. The L-5 position is very much in favor of SPS; CEP is very much opposed and FASST is relatively neutral. The responses are analyzed, and from the responses some questions and answers about the satellite power system are presented in the appendix. (WHK)

SPS Abundance - Salmon Population Summary Database

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The data contained in the SPS database are primarily summary data, compiled at the population level and available through the SPS website...

Integration of SPS with utility system networks

Science.gov (United States)

Kaupang, B. M.

1980-01-01

The integration of Satellite Power System (SPS) power in electric utility power systems is discussed. Specifically, the nature of the power output variations from the spacecraft to the rectenna, the operational characteristics of the rectenna power, and the impacts on the electric utility system from utilizing SPS power to serve part of the system load are treated. It is concluded that if RF beam control is an acceptable method for power control, and that the site distribution of SPS rectennas do not cause a very high local penetration (40 to 50%), SPS may be integrated into electric utility system with a few negative impacts. Increased regulating duty on the conventional generation, and a potential impact on system reliability for SPS penetration in excess of about 25% appear to be two areas of concern.

Simulation of E-Cloud Driven Instability And Its Attenuation Using a Feedback System in the CERN SPS

International Nuclear Information System (INIS)

Vay, Jean-Luc

2012-01-01

Electron clouds have been shown to trigger fast growing instabilities on proton beams circulating in the SPS, and a feedback system to control the instabilities is under active development. We present the latest improvements to the Warp-Posinst simulation framework and feedback model, and its application to the self-consistent simulations of two consecutive bunches interacting with an electron cloud in the SPS.

Satellite Power System (SPS) Program Summary

Energy Technology Data Exchange (ETDEWEB)

1978-12-01

The joint DOE/NASA SPS program has as its objective to achieve by the end of 1980 an initial understanding of the technical feasibility, economic practicability, and the social and environmental acceptability of the SPS concepts so that recommendations concerning program continuation can be made. The four major study areas include (1) systems definition; (2) environmental assessment; (3) societal assessment; and (4) comparative assessment of alternative energy systems. All the projects on the SPS program are listed and summarized for FY 1978. (WHK)

Satellite Power System (SPS) financial/management scenarios

Science.gov (United States)

Vajk, J. P.

1978-01-01

The possible benefits of a Satellite Power System (SPS) program, both domestically and internationally, justify detailed and imaginative investigation of the issues involved in financing and managing such a large-scale program. In this study, ten possible methods of financing a SPS program are identified ranging from pure government agency to private corporations. The following were analyzed and evaluated: (1) capital requirements for SPS; (2) ownership and control; (3) management principles; (4) organizational forms for SPS; (5) criteria for evaluation; (6) detailed description and preliminary evaluation of alternatives; (7) phased approaches; and (8) comparative evaluation. Key issues and observations and recommendations for further study are also presented.

SIMULATION OF E-CLOUD DRIVEN INSTABILITY AND ITS ATTENUATION USING A FEEDBACK SYSTEM IN THE CERN SPS

International Nuclear Information System (INIS)

Vay, J.-L.; Byrd, J.M.; Furman, M.A.; Secondo, R.; Venturini, M.; Fox, J.D.; Rivetta, C.H.; Hofle, W.

2010-01-01

Electron clouds have been shown to trigger fast growing instabilities on proton beams circulating in the SPS (1), and a feedback system to control the instabilities is under active development (2). We present the latest improvements to the Warp-Posinst simulation framework and feedback model, and its application to the self-consistent simulations of two consecutive bunches interacting with an electron cloud in the SPS.

SPS Beam Steering for LHC Extraction

Energy Technology Data Exchange (ETDEWEB)

Gianfelice-Wendt, Eliana [Fermilab; Bartosik, Hannes [CERN; Cornelis, Karel [CERN; Norderhaug Drøsdal, Lene [CERN; Goddard, Brennan [CERN; Kain, Verena [CERN; Meddahi, Malika [CERN; Papaphilippou, Yannis [CERN; Wenninger, Jorg [CERN

2014-07-01

The CERN Super Proton Synchrotron accelerates beams for the Large Hadron Collider to 450 GeV. In addition it produces beams for fixed target facilities which adds complexity to the SPS operation. During the run 2012-2013 drifts of the extracted beam trajectories have been observed and lengthy optimizations in the transfer lines were performed to reduce particle losses in the LHC. The observed trajectory drifts are consistent with the measured SPS orbit drifts at extraction. While extensive studies are going on to understand, and possibly suppress, the source of such SPS orbit drifts the feasibility of an automatic beam steering towards a “golden” orbit at the extraction septa, by means of the interlocked correctors, is also being investigated. The challenges and constraints related to the implementation of such a correction in the SPS are described. Simulation results are presented and a possible operational steering strategy is proposed.

The experimental programme of the SPS

CERN Document Server

Kluyver, J C

1977-01-01

Early success with the CERN 28 GeV proton synchrotron (PS) prompted three questions about the future. Which areas of high energy particle physics would offer the best chance of progress, and with which accelerators? Which detectors would be needed? What experiments would be most likely to succeed? About 1963 it was suggested that the PS be extended with intersecting storage rings (ISR), and a 300 GeV SPS be built. By 1971 the ISR was ready for experiments, and the SPS proposal approved. At the present time the SPS programme comprises 28 experiments in the West Hall. (0 refs).

SPS batch spacing optimisation

CERN Document Server

Velotti, F M; Carlier, E; Goddard, B; Kain, V; Kotzian, G

2017-01-01

Until 2015, the LHC filling schemes used the batch spac-ing as specified in the LHC design report. The maximumnumber of bunches injectable in the LHC directly dependson the batch spacing at injection in the SPS and hence onthe MKP rise time.As part of the LHC Injectors Upgrade project for LHCheavy ions, a reduction of the batch spacing is needed. In thisdirection, studies to approach the MKP design rise time of150ns(2-98%) have been carried out. These measurementsgave clear indications that such optimisation, and beyond,could be done also for higher injection momentum beams,where the additional slower MKP (MKP-L) is needed.After the successful results from 2015 SPS batch spacingoptimisation for the Pb-Pb run [1], the same concept wasthought to be used also for proton beams. In fact, thanksto the SPS transverse feed back, it was already observedthat lower batch spacing than the design one (225ns) couldbe achieved. For the 2016 p-Pb run, a batch spacing of200nsfor the proton beam with100nsbunch spacing wasreque...

The potency of the SPS Agreement’s ‘excessivity test’

NARCIS (Netherlands)

Schebesta, H.; Sinopoli, D.A.

2018-01-01

The article investigates the current and potential relevance of Article 5.6 SPS in deciding SPS disputes, and its impact on trade liberalization and WTO Members’ power to take sanitary and phytosanitary measures.
Article 5.6 of the SPS Agreement states that SPS measures may not be more trade

Longitudinal Space Charge in the SPS

CERN Document Server

Lasheen, Alexandre

2016-01-01

Longitudinal instabilities due to the SPS beam coupling impedance are a major issue for future projects and it is essential to have an accurate SPS impedance model to study them. The longitudinal space charge effect can be modelled by a pure reactive impedance and should also be included in simulations as it may have an impact at low energy. In this Note, the effect of the longitudinal space charge in the SPS is evaluated by taking into account the variation of the transverse beam size and vacuum chamber geometry along the ring. Scaling laws are used to investigate what are the most important parameters for the evaluation of the longitudinal space charge impedance.

Kaon pseudorapidity distribution in pA and AA collisions at AGS and SPS energies

International Nuclear Information System (INIS)

Liu, Fuhu; Zhang, Donghai; Duan, Maiying; Allah, Nabil N. Abd

2003-01-01

We study systematically the kaon pseudorapidity distribution in proton-nucleus and nucleus-nucleus collisions at AGS and SPS energies within the cylinder model. The calculated results are compared and shown to be in agreement with the available experimental data. (author)

Beam measurements of the SPS longitudinal impedance

CERN Document Server

Lasheen, A

2017-01-01

Longitudinal instabilities are one of the main limitationsin the CERN SPS to reach the beam parameters requiredfor the High Luminosity LHC project. In preparation tothe SPS upgrade, possible remedies are studied by perform-ing macroparticle simulations using the machine impedancemodel obtained from electromagnetic simulations and mea-surements. To benchmark the impedance model, the resultsof simulations are compared with various beam measure-ments. In this study, the reactive part of the impedance wasprobed by measuring the quadrupole frequency shift withintensity, obtained from bunch length oscillations at mis-matched injection into the SPS. This method was appliedover many last years to follow up the evolution of the SPSimpedance, injecting bunches with the same bunch length.A novel approach, giving significantly more information,consists in varying the injected bunch length. The compari-son of these measurements with macroparticle simulationsallowed to test the existing model and identify some missingSPS i...

Coupling Impedance of the CERN SPS beam position monitors

CERN Document Server

Salvant, B; Boccard, C; Caspers, Friedhelm; Grudiev, A; Jones, R; Métral, E; Rumolo, G; Zannini, C; Spataro, B; Alesini, D; Migliorati, M; Roncarolo, F; Calaga, R

2010-01-01

A detailed knowledge of the beam coupling impedance of the CERN Super Proton Synchrotron (SPS) is required in order to operate this machine with a higher intensity for the foreseen Large Hadron Collider (LHC) luminosity upgrade. A large number of Beam Position Monitors (BPMs) is currently installed in the SPS, and this is why their contribution to the SPS impedance has to be assessed. This paper focuses on electromagnetic (EM) simulations and bench measurements of the longitudinal and transverse impedance generated by the horizontal and vertical BPMs installed in the SPS machine.

The 938 MHz resonant damping loops for the 200 MHz SPS travelling wave cavities

CERN Document Server

Caspers, F

2012-01-01

Measurements of the beam stability in the SPS in 1982 - 1983 have shown a transversal instability for high intensity beams [1]. The fact that this related technical note is published nearly 30 years later, is related to the revival of interest in the frame of SPS impedance evaluation for LS1. Until now there was just a barely known paper folder available which could be consulted on request. The instability mentioned above was identified from beam measurements as raised by a deflecting mode at approximately 940 MHz in the 200 MHz travelling wave cavities of the SPS. Estimates showed that an attenuation of this particular mode by 20 dB would be desirable. In order to achieve this attenuation some vacuum ports on top of the cavities were available. For the damping devices three requirements had to be met: - sufficient damping at about 940 MHz - no serious change of cavity input VSWR at 200 MHz - no water cooling requirement for this higher order mode coupler.

Longitudinal stability of the LHC beam in the SPS

CERN Document Server

Shaposhnikova, Elena

2001-01-01

Longitudinal beam stability is analysed for the LHC Beam in the SPS. The most critical area is shown to be the top energy. Analysis explains some results of measurements with the beam done d uring the MDs last year. The possibility of using this cycle for CNGS is considered as well. There, without special requirements on bunch parameters at extraction, the impedance limitations move to the lowest energy. An option with low transition energy is presented also.

SPS extraction systems

CERN Multimedia

CERN PhotoLab

1973-01-01

One of the 3-m long electrostatics septa. The septum itself consists of 0.15 mm thick molybdenum wires with a 1.5 mm pitch. Each of the two SPS extraction systems will contain four of these electrostatic septa.

New control architecture for the SPS accelerator at CERN

International Nuclear Information System (INIS)

Kissler, K.H.; Rausch, R.

1992-01-01

The Control System for the 450 Gev proton accelerator SPS at CERN was conceived and implemented some 18 years ago. The 16 Bit minicomputers with their proprietary operating system and interconnection with a dedicated network do not permit the use of modern workstations, international communication standards and industrial software packages. The upgrading of the system has therefore become necessary. After a short review of the history and the current state of the SPS control system, the paper describes how CERN's new control architecture, which will be common to all accelerators, will be realized at the SPS. The migration path ensuring a smooth transition to the final system is outlined. Once the SPS upgrade is complete and following some enhancements to the LEP control system, the operator in the SPS/LEP control center will be working in a single uniform control environment. (author)

Stiff person syndrome (SPS: Literature review and case report

Directory of Open Access Journals (Sweden)

Erna Pretorius

2013-11-01

Full Text Available Stiff person syndrome (SPS is a rare, debilitating condition which presents with progressive and inconsistent neurological features. The main symptoms are stiffness and intermittent, painful muscle spasms, triggered and exacerbated by stressful and emotional stimuli. The fluctuating clinical nature of SPS, and otherwise normal neurological examination, often lead to a misdiagnosis of conversion disorder. Psychiatric symptoms frequently accompany this disorder and patients are often first seen by psychiatrists. SPS is autoimmune-based: antibodies are directed against glutamate decarboxylase, resulting in dysregulation of gamma-aminobutyric acid (GABA in the brain which is considered the cause of the neuropsychiatric symptomatology. SPS should be considered in the differential diagnosis of conversion disorder. Effective management requires early detection, a collaborative approach with GABA-ergic medication and intravenous immunoglobulins, and management of concomitant psychiatric disorders. We describe a patient with SPS. Only one other case has been reported in South Africa.

Mission critical database for SPS accelerator measurements

CERN Document Server

Billen, R; Laugier, I; Reguero, I; Segura, N

1995-01-01

In order to maintain efficient control over the hadron and lepton beams in CERN¹s SPS accelerator, measurements are of vital importance. Beam parameters such as intensities, positions and losses need to be rapidly available in the SPS control room to allow the operators to monitor, judge and act on beam physics conditions. For the 1994 SPS startup, a completely new and redesigned measurement system based on client and server C-programs running on UNIX-workstations was introduced. The kernel of this new measurement system is an on-line ORACLE database.The NIAM method was used for the database design as well as a technique to tag synchronized data with timeslots instead of timestamps. A great attention was paid to proper storage allocation for tables and indices since this has a major impact on the efficiency of the database, due to its time-critical nature. Many new features of Oracle7 were exploited to reduce the surrounding software.During the 1994 SPS physics run, this new measurement system was commission...

A Facility to Search for Hidden Particles (SHiP) at the CERN SPS

CERN Document Server

Anelli, M.; Arduini, G.; Back, J.J.; Bagulya, A.; Baldini, W.; Baranov, A.; Barker, G.J.; Barsuk, S.; Battistin, M.; Bauche, J.; Bay, A.; Bayliss, V.; Bellagamba, L.; Bencivenni, G.; Bertani, M.; Bezshyyko, O.; Bick, D.; Bingefors, N.; Blondel, A.; Bogomilov, M.; Boyarsky, A.; Bonacorsi, D.; Bondarenko, D.; Bonivento, W.; Borburgh, J.; Bradshaw, T.; Brenner, R.; Breton, D.; Brook, N.; Bruschi, M.; Buonaura, A.; Buontempo, S.; Cadeddu, S.; Calcaterra, A.; Calviani, M.; Campanelli, M.; Capoccia, C.; Cecchetti, A.; Chatterjee, A.; Chauveau, J.; Chepurnov, A.; Chernyavskiy, M.; Ciambrone, P.; Cicalo, C.; Conti, G.; Cornelis, K.; Courthold, M.; Dallavalle, M.G.; D'Ambrosio, N.; De Lellis, G.; De Serio, M.; Dedenko, L.; Di Crescenzo, A.; Di Marco, N.; Dib, C.; Dietrich, J.; Dijkstra, H.; Domenici, D.; Donskov, S.; Druzhkin, D.; Ebert, J.; Egede, U.; Egorov, A.; Egorychev, V.; Alaoui, M. A. El; Enik, T.; Etenko, A.; Fabbri, F.; Fabbri, L.; Fedorova, G.; Felici, G.; Ferro-Luzzi, M.; Fini, R.A.; Franke, M.; Fraser, M.; Galati, G.; Giacobbe, B.; Goddard, B.; Golinka-Bezshyyko, L.; Golubkov, D.; Golutvin, A.; Gorbunov, D.; Graverini, E.; Grenard, J-L; Guler, A.M.; Hagner, C.; Hakobyan, H.; Helo, J.C.; van Herwijnen, E.; Horvath, D.; Iacovacci, M.; Iaselli, G.; Jacobsson, R.; Kadenko, I.; Kamiscioglu, M.; Kamiscioglu, C.; Khaustov, G.; Khotjansev, A.; Kilminster, B.; Kim, V.; Kitagawa, N.; Kodama, K.; Kolesnikov, A.; Kolev, D.; Komatsu, M.; Konovalova, N.; Koretskiy, S.; Korolko, I.; Korzenev, A.; Kovalenko, S.; Kudenko, Y.; Kuznetsova, E.; Lacker, H.; Lai, A.; Lanfranchi, G.; Lauria, A.; Lebbolo, H.; Levy, J. -M.; Lista, L.; Loverre, P.; Lukiashin, A.; Lyubovitskij, V.E.; Malinin, A.; Manfredi, M.; Perillo-Marcone, A.; Marrone, A.; Matev, R.; Messomo, E.N.; Mermod, P.; Mikado, S.; Mikhaylov, Yu.; Miller, J.; Milstead, D.; Mineev, O.; Mingazheva, R.; Mitselmakher, G.; Miyanishi, M.; Monacelli, P.; Montanari, A.; Montesi, M.C.; Morello, G.; Morishima, K.; Movtchan, S.; Murzin, V.; Naganawa, N.; Naka, T.; Nakamura, M.; Nakano, T.; Nurakhov, N.; Obinyakov, B.; Ocalan, K.; Ogawa, S.; Oreshkin, V.; Orlov, A.; Osborne, J.; Pacholek, P.; Panman, J.; Paoloni, A.; Paparella, L.; Pastore, A.; Patel, M.; Petridis, K.; Petrushin, M.; Poli-Lener, M.; Polukhina, N.; Polyakov, V.; Prokudin, M.; Puddu, G.; Pupilli, F.; Rademakers, F.; Rakai, A.; Rawlings, T.; Redi, F.; Ricciardi, S.; Rinaldesi, R.; Roganova, T.; Rogozhnikov, A.; Rokujo, H.; Romaniouk, A.; Rosa, G.; Rostovtseva, I.; Rovelli, T.; Ruchayskiy, O.; Ruf, T.; Saitta, G.; Samoylenko, V.; Samsonov, V.; Ull, A. Sanz; Saputi, A.; Sato, O.; Schmidt-Parzefall, W.; Serra, N.; Sgobba, S.; Shaposhnikov, M.; Shatalov, P.; Shaykhiev, A.; Shchutska, L.; Shevchenko, V.; Shibuya, H.; Shitov, Y.; Silverstein, S.; Simone, S.; Skorokhvatov, M.; Smirnov, S.; Solodko, E.; Sosnovtsev, V.; Spighi, R.; Spinetti, M.; Starkov, N.; Storaci, B.; Strabel, C.; Strolin, P.; Takahashi, S.; Teterin, P.; Tioukov, V.; Tommasini, D.; Treille, D.; Tsenov, R.; Tshchedrina, T.; Ustyuzhanin, A.; Vannucci, F.; Venturi, V.; Villa, M.; Vincke, Heinz; Vincke, Helmut; Vladymyrov, M.; Xella, S.; Yalvac, M.; Yershov, N.; Yilmaz, D.; Yilmazer, A.U.; Vankova-Kirilova, G.; Zaitsev, Y.; Zoccoli, A.; CERN. Geneva. SPS and PS Experiments Committee; SPSC

2015-01-01

A new general purpose fixed target facility is proposed at the CERN SPS accelerator which is aimed at exploring the domain of hidden particles and make measurements with tau neutrinos. Hidden particles are predicted by a large number of models beyond the Standard Model. The high intensity of the SPS 400~GeV beam allows probing a wide variety of models containing light long-lived exotic particles with masses below ${\\cal O}$(10)~GeV/c$^2$, including very weakly interacting low-energy SUSY states. The experimental programme of the proposed facility is capable of being extended in the future, e.g. to include direct searches for Dark Matter and Lepton Flavour Violation. The facility will be serviced by a new dedicated beam line branched off the splitter section on the North Area. It is followed by a new target station and a magnetic shield to suppress beam induced background. The proposed orientation of the beam line and the underground complex allows reserving more than 100~m of space beyond the experiment...

Searching for Quark Matter at the CERN SPS

CERN Document Server

Lourenço, C

2002-01-01

This article gives a brief overview of some recent advances in our understanding of the physics of dense strongly interacting matter, from measurements done at the CERN SPS. The presently available results are very interesting, and are likely to reflect the production of a new state of matter in central Pb-Pb collisions, at the highest SPS energies. However, important questions require further work. Particular emphasis is given to developments made since the Quark Matter 1999 conference, and to issues that justify the continuation of the SPS heavy ion physics program beyond year 2000.

Development of a short form Social Interaction Anxiety (SIAS) and Social Phobia Scale (SPS) using nonparametric item response theory: the SIAS-6 and the SPS-6.

Science.gov (United States)

Peters, Lorna; Sunderland, Matthew; Andrews, Gavin; Rapee, Ronald M; Mattick, Richard P

2012-03-01

Shortened forms of the Social Interaction Anxiety Scale (SIAS) and the Social Phobia Scale (SPS) were developed using nonparametric item response theory methods. Using data from socially phobic participants enrolled in 5 treatment trials (N = 456), 2 six-item scales (the SIAS-6 and the SPS-6) were developed. The validity of the scores on the SIAS-6 and the SPS-6 was then tested using traditional methods for their convergent validity in an independent clinical sample and a student sample, as well as for their sensitivity to change and diagnostic sensitivity in the clinical sample. The scores on the SIAS-6 and the SPS-6 correlated as well as the scores on the original SIAS and SPS, with scores on measures of related constructs, discriminated well between those with and without a diagnosis of social phobia, providing cutoffs for diagnosis and were as sensitive to measuring change associated with treatment as were the SIAS and SPS. Together, the SIAS-6 and the SPS-6 appear to be an efficient method of measuring symptoms of social phobia and provide a brief screening tool.

The CERN 400 GeV proton synchrotron (CERN SPS)

International Nuclear Information System (INIS)

Adams, J.B.

1977-01-01

The main characteristics of the CERN 400 GeV proton synchrotron (SPS) has described. Beam intensity averages about 5x10 12 protons per pulse. The CERN 28 GeV proton synchrotron serves as an injector for the SPS. There are 108 magnet periods in the machine with a phase shift per period of π/2. The magnet system consists of 800 dipoles with 1.8 T magnetic field and 216 quadrupoles with a field gradient of 20.7 T (per meter). The frequency chosen for the RF system of the SPS is 200 MHz. Two beam extraction systems are installed in the SPS, one to feed protons to the West Experimental Area, and the other to feed protons to the North Experimental Area. The planned development of the machine in the next few years has described. The cost per GeV of the SPS works out 3 to 4 times less than that of the CPS

Possibility of high efficient beam extraction from the CERN SPS with a bent crystal. Simulation results

Energy Technology Data Exchange (ETDEWEB)

Scandale, W. [CERN, European Organization for Nuclear Research, CH-1211 Geneva 23 (Switzerland); Laboratoire de l' AccelerateurLineaire (LAL), Universite Paris SudOrsay, Orsay (France); INFN Sezione di Roma, Piazzale Aldo Moro 2, 00185 Rome (Italy); Kovalenko, A.D.; Taratin, A.M. [Joint Institute for Nuclear Research, 141980 Dubna, Moscow Region (Russian Federation)

2017-03-11

The extraction of the SPS beam of 270 GeV/c protons assisted by a bent crystal was studied by simulation. Two methods for delivering the SPS beam onto a crystal were considered: transverse diffusion and orbit bump of the beam. It was shown that the main condition for high efficient beam extraction with a bent crystal, which is a small divergence of the incident beam, can be fulfilled. Extraction efficiency up to 99% can be reached for both methods of the beam delivering. The irradiation of the electrostatic septum wires during the beam extraction can be considerably reduced.

SPS commemorative stamp

CERN Multimedia

1977-01-01

The turn on of the SPS was commemorated in France by the issue of a CERN stamp. The date of issue, 22 Octber 1976, coincided with the first tests of the beam line taking particles to experiments in the West Hall. (CERN Courier 1976 p. 382)

Integration of SPS with utility system networks

Energy Technology Data Exchange (ETDEWEB)

Kaupang, B.M.

1980-06-01

This paper will discuss the integration of SPS power in electric utility power systems. Specifically treated will be the nature of the power output variations from the spacecraft to the rectenna, the operational characteristics of the rectenna power and the impacts on the electric utility system from utilizing SPS power to serve part of the system load.

A 25th Anniversary Rejuvenation for the SPS

CERN Multimedia

2001-01-01

The SPS has just turned 25, and to mark the occasion it has been treated to a facelift like none before. After serving as injector for LEP, the SPS is being prepared to pre-accelerate proton beams for the LHC.

Upgrades to the SPS-to-LHC Transfer Line Beam Stoppers for the LHC High-Luminosity Era

CERN Document Server

Kain, Verena; Fraser, Matthew; Goddard, Brennan; Meddahi, Malika; Perillo Marcone, Antonio; Steele, Genevieve; Velotti, Francesco

2016-01-01

Each of the 3 km long transfer lines between the SPS and the LHC is equipped with two beam stoppers (TEDs), one at the beginning of the line and one close to the LHC injection point, which need to absorb the full transferred beam. The beam stoppers are used for setting up the SPS extractions and transfer lines with beam without having to inject into the LHC. Energy deposition and thermo-mechanical simulations have, however, shown that the TEDs will not be robust enough to safely absorb the high intensity beams foreseen for the high-luminosity LHC era. This paper will summarize the simulation results and limitations for upgrading the beam stoppers. An outline of the hardware upgrade strategy for the TEDs together with modifications to the SPS extraction interlock system to enforce intensity limitations for beam on the beam stoppers will be given.

The promoter activities of sucrose phosphate synthase genes in rice, OsSPS1 and OsSPS11, are controlled by light and circadian clock, but not by sucrose

Directory of Open Access Journals (Sweden)

Madoka eYonekura

2013-03-01

Full Text Available Although sucrose plays a role in sugar sensing and its signaling pathway, little is known about the regulatory mechanisms of the expressions of plant sucrose-related genes. Our previous study on the expression of the sucrose phosphate synthase gene family in rice (OsSPSs suggested the involvement of sucrose sensing and/or circadian rhythm in the transcriptional regulation of OsSPS. To examine whether the promoters of OsSPSs can be controlled by sugars and circadian clock, we produced transgenic rice plants harboring a promoter–luciferase construct for OsSPS1 or OsSPS11 and analyzed the changes in the promoter activities by monitoring bioluminescence from intact transgenic plants in real time. Transgenic plants fed sucrose, glucose, or mannitol under continuous light conditions showed no changes in bioluminescence intensity; meanwhile, the addition of sucrose increased the concentration of sucrose in the plants, and the mRNA levels of OsSPS remained constant. These results suggest that these OsSPS promoters may not be regulated by sucrose levels in the tissues. Next, we investigated the changes in the promoter activities under 12-h light/12-h dark cycles and continuous light conditions. Under the light–dark cycle, both OsSPS1 and OsSPS11 promoter activities were low in the dark and increased rapidly after the beginning of the light period. When the transgenic rice plants were moved to the continuous light condition, both POsSPS1::LUC and POsSPS11::LUC reporter plants exhibited circadian bioluminescence rhythms; bioluminescence peaked during the subjective day with a 27-h period: in the early morning as for OsSPS1 promoter and midday for OsSPS11 promoter. These results indicate that these OsSPS promoters are controlled by both light illumination and circadian clock and that the regulatory mechanism of promoter activity differs between the 2 OsSPS genes.

New Working Conditions for the SPS from 2000

CERN Document Server

Nonis, M

2000-01-01

After the long shutdown (December 2000 to May 2001), the SPS complex will work with the main water-cooling loop in closed circuit. This will affect the working conditions because of the higher temperature of the supplied water (24 ° C, i.e. 15 K higher) and therefore of the air in the tunnel. The cooling installations will consequently be upgraded or replaced to meet the new needs, and several new chilled-water stations will be installed to supply the present users. The author will thoroughly explain the main aspects of all these modifications and report the results of the preliminary tests carried out in September 1996. Finally, an overview of the global costs (operational and linked to the project) will be given, taking into account the different consumption of water, electricity and the effects on the magnet components.

Emittance growth in coast in the SPS

CERN Document Server

Alekou, A; Bartosik, H; Calaga, R

2017-01-01

The CERN SPS will be used as a test-bed for the LHCprototype crab-cavities, which will be installed and testedin the SPS in 2018. As the time available for experimen-tal beam dynamics studies with the crab cavities installedin the machine will be limited, a very good preparation isrequired in advance. One of the main concerns is the in-duced emittance growth, driven by phase jitter in the crabcavities. In this respect, several machine development (MD)studies were performed during the past years to quantifyand characterize the emittance evolution of proton beamsin coast in the SPS. In these proceedings, the experimentalobservations from past years are summarized and the MDstudies from 2016 are presented. Finally, a proposal for anexperimental program for 2017 is discussed.

Characterization of the SPS 800MHz travelling wave cavities.

CERN Document Server

Bazyl, Dmitry

2015-01-01

It is well known that HOMs in RF cavities are a potentially dangerous source of beam impedance. Therefore, HOMs (both longitudinal and transverse) can drive the beam unstable . The 800MHz cavities of the SPS were studied in the past. However, very little documentation was left behind. Currently, the performance of the SPS is limited by a longitudinal beam instability. In order to study this instability, an accurate impedance model of the whole SPS is needed.

Potential interest in Europe in SPS development

Energy Technology Data Exchange (ETDEWEB)

Reinhartz, K K

1980-06-01

The Solar Satellite Power System is a concept whereby large solar-energy converters are placed in outer space and the electrical energy produced is transmitted back to earth as microwave radiation. A number of studies, performed mainly in the United States, are aimed at assessing the technical, economic, social and health aspects of this concept. This paper does not address the feasibility of the SPS as such, but discusses the potential contribution that an SPS could make to the European energy scenario, the economic impact of the SPS as an indigenous European energy source, and the potential importance of the SPS as a technology driver. A European network of forty solar power satellites could supply electrical energy equal to Europe's present electrical energy production and significantly reduce Europe's dependence on energy imports. Additionally the development of a power satellite technology, if started by the United States, is expected to lead to such an advancement in technology in key areas, e.g., space industrialisation, photovoltaic energy conversion and wireless transmission of energy, that Europe would rapidly lose technical competence in many important fields if it were not to participate.

Electrostatic septum for "Continuous Transfer" from PS to SPS

CERN Multimedia

CERN PhotoLab

1982-01-01

For "Continuous Transfer" to the SPS, the PS beam, after acceleration, is peeled off in 5 turns. To minimize losses, the magnetic septa are preceded by an electrostatic septum in straight section 31. We see the inner part of it, on a lab-bench. The first part consists of W-wires, the second part is a Mo-foil. The circulating beam passes through the opening, the ejected beam at the outside (above the wires, in this picture). This assembly is the anode-part, the cathode is not shown.

Visiting the SPS installation

CERN Multimedia

1975-01-01

...., Guenther Loehr, Hans Horisberger walk along the SPS tunnel: here, on the right, an absorber block of 22 tons for beam dumping in the external beam lines. The chariot serves for the installation of the block.

Beam Losses and Lifetime of the LHC Beam in the SPS

CERN Document Server

Bohl, T; Shaposhnikova, Elena; Tückmantel, Joachim

2006-01-01

Studies of the LHC beam loss in the SPS started in 2003 [1], [2] and continued in 2004. The flat bottom losses strongly depend on the batch intensity and the RF voltage. For beam with the 75 ns spacing at the same bunch intensity they are smaller than for the 25 ns spaced bunches. Large voltage on the flat bottom together with some optimum voltage at injection helps to reduce losses. Analysis of data from 2003 has shown that observations are compatible with a diffusion like process on the flat bottom. Therefore significant time during 2004 was devoted to studies of possible RF noise sources. However the main improvement in beam lifetime on the flat bottom was observed after a change in the working point in the transverse plane (MD on 1.09.2004). In this Note we present measurements of beam loss and lifetime done during several dedicated SPS MDs for different conditions in the ring. Analysis of beam coasts will be presented separately.

Life after discovery: a look at the SPS of 2012

CERN Multimedia

Katarina Anthony

2012-01-01

Though no longer the newest kid on the block, the SPS remains as essential to CERN’s research programme as it was when it discovered the W and Z bosons back in 1983. The CERN Bulletin takes a look at how the SPS has kept up with younger CERN accelerators...   Teams changing an SPS magnet during a technical stop. Image courtesy of Franck Bais. It’s the 1970s and the Super Proton Synchrotron (SPS) is at the top of the charts. It’s accelerating protons at 400 GeV - an unprecedented energy for CERN - and its discoveries will make it the first (and, so far, the only) CERN accelerator to generate a Nobel Prize. Fast-forward to 2012 and the SPS is running at 450 GeV – well beyond its original design parameters – and is an essential part of the LHC accelerator complex. Not bad for a machine heading into its 40s. While much of the SPS dates back to the original set-up, it has been in constant evolution over the years. Except for a long shutdo...

Analysis of the SPS Long Term Orbit Drifts

Energy Technology Data Exchange (ETDEWEB)

Velotti, Francesco [CERN; Bracco, Chiara [CERN; Cornelis, Karel [CERN; Drøsdal, Lene [CERN; Fraser, Matthew [CERN; Gianfelice-Wendt, Eliana [Fermilab; Goddard, Brennan [CERN; Kain, Verena [CERN; Meddahi, Malika [CERN

2016-06-01

The Super Proton Synchrotron (SPS) is the last accelerator in the Large Hadron Collider (LHC) injector chain, and has to deliver the two high-intensity 450 GeV proton beams to the LHC. The transport from SPS to LHC is done through the two Transfer Lines (TL), TI2 and TI8, for Beam 1 (B1) and Beam 2 (B2) respectively. During the first LHC operation period Run 1, a long term drift of the SPS orbit was observed, causing changes in the LHC injection due to the resulting changes in the TL trajectories. This translated into longer LHC turnaround because of the necessity to periodically correct the TL trajectories in order to preserve the beam quality at injection into the LHC. Different sources for the SPS orbit drifts have been investigated: each of them can account only partially for the total orbit drift observed. In this paper, the possible sources of such drift are described, together with the simulated and measured effect they cause. Possible solutions and countermeasures are also discussed.

SPS injection kicker magnet

CERN Document Server

1975-01-01

One of the first-generation SPS injection kicker magnets. Lifting the tank-lid reveals the inner structure. For a more detailed description see 7502072X. See also 7502074X and Annual Report 1975, p.162. To the left: Roland Tröhler; to the right: Giacomo Busetta.

Transverse Phenomena in Pion Production in Hadronic Collisions at SPS energy

CERN Document Server

Chvála, Ondrej

A comparative study of pion production in hadronic collisio ns at SPS energies focusing on transverse phenomena is presented. Charged pion densities in p+p, p+C, p+Pb and Pb+Pb interactions, obtained at the CERN SPS with the NA49 detecto r setup, are discussed in the forward hemisphere covering ranges in Feynman x F between 0 and 0.4 and in transverse momentum from 0 to 2.1 GeV/c. A detailed description of the da ta analysis, the corrections and centrality determination is given for p+Pb interaction s using a sample of 2 M events. These data are compared to p+p collisions in order to extract those physics quantities which indicate deviations from the elementary reaction specific t o the presence of the nucleus. The evolution of these quantities as a function of centrality is discussed. Their comparison to p+C and Pb+Pb collisions reveals a smooth dependence on the n umber of collisions per participant. In particular, the enhancement of pion yields at high transverse momentum is studied. It is shown to be gove...

Status of UA9, the Crystal Collimation Experiment in the SPS

CERN Document Server

Scandale, W

2011-01-01

UA9 was operated at the CERN-SPS for more than two years to investigate the feasibility of halo collimation with bent crystals. Silicon crystals 2 mm long with bending angles of about 170 μrad were used as primary collimators. The crystal collimation process was steadily achieved through channeling, with high efficiency. The crystal orientation was easily set and optimized with an installed goniometer that has an angular accuracy of about ± 10 μrad. In channeling orientation, the loss rate of the halo particles interacting with the crystal is reduced by half an order of magnitude, whilst the residual off momentum halo escaping from the crystal-collimator area is reduced by a factor two to five. The crystal channeling efficiency of about 75% is reasonably consistent with simulations and with single pass data collected in the extracted proton beam of the SPS North Experimental Area. The accumulated observations, shown in this paper, support our expectation that the coherent deflection of the beam halo by a b...

CrossRef Experimental verification of the HERD prototype at CERN SPS

CERN Document Server

Dong, Yongwei; Wang, Junjing; Xu, Ming; Albergo, Sebastiano; Ambroglini, Filippo; Ambrosi, Giovanni; Azzarello, Philipp; Bai, Yonglin; Bao, Tianwei; Baldini, Luca; Battiston, Roberto; Bernardini, Paolo; Chen, Zhen; D'Alessandro, Raffaello; Duranti, Matteo; D'Urso, Domenico; Fusco, Piergiorgio; Gao, Jiarui; Gao, Xiaohui; Gargano, Fabio; Giglietto, Nicola; Hu, Bingliang; Li, Ran; Li, Yong; Liu, Xin; Loparco, Francesco; Lu, Junguang; Marsella, Giovanni; Mazziotta, Mario N; De Mitri, Ivan; Mori, Nicola; Orsi, Silvio; Oscar, Adriani; Pearce, Mark; Pohl, Martin; Ryde, Felix; Shi, Dalian; Spillantini, Piero; Su, Meng; Sun, Xin; Surdo, Antonio; Walter, Roland; Wang, Bo; Wang, Le; Wang, Ruijie; Wang, Zhigang; Wu, Bobing; Wu, Xin; Yan, Peng; Zhang, Li; Zhang, Shuangnan

2016-01-01

The High Energy cosmic-Radiation Detection (HERD) facility is one of several space astronomy payloads of the cosmic light house program onboard China's Space Station, which is planned for operation starting around 2020 for about 10 years. Beam test with a HERD prototype, to verify the HERD specifications and the reading out method of wavelength shifting fiber and image intensified CCD, was taken at CERN SPS in November, 2015. The prototype is composed of an array of 5*5*10 LYSO crystals, which is 1/40th of the scale of HERD calorimeter. Experimental results on the performances of the calorimeter are discussed. © (2016) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE). Downloading of the abstract is permitted for personal use only.

Impedance Characterisation of the SPS Wire Scanner

CERN Document Server

AUTHOR|(CDS)2091911; Prof. Sillanpää, Mika

As a beam diagnostic tool, the SPS wire scanner interacts with the proton bunches traversing the vacuum pipes of the Super Proton Synchrotron particle accelerator. Following the interaction, the bunches decelerate or experience momentum kicks off-axis and couple energy to the cavity walls, resonances and to the diagnostic tool, the scanning wire. The beam coupling impedance and, in particular, the beam induced heating of the wire motivate the characterisation and redesign of the SPS wire scanner. In this thesis, we characterise RF-wise the low frequency modes of the SPS wire scanner. These have the highest contribution to the impedance. We measure the cavity modes in terms of resonance frequency and quality factor by traditional measurement techniques and data analysis. We carry out a 4-port measurement to evaluate the beam coupling to the scanning wire, that yields the spectral heating power. If combined with the simulations, one is able to extract the beam coupling impedance and deduce the spectral dissipa...

Modifications to the SPS LSS6 Septa for LHC and the SPS Septa Diluters

CERN Document Server

Borburgh, Y; Goddard, B; Kadi, Y

2006-01-01

The Large Hadron Collider required the modification of the existing extraction channel in the long straight section (LSS) 6 of the CERN Super Proton Synchrotron (SPS), including the suppression of the electrostatic wire septa. The newly set up fast extraction will be used to transfer protons at 450 GeV/c as well as ions via the 2.9 km long transfer line TI 2 to Ring 1 of the LHC. The girder of the existing SPS DC septa was modified to accommodate a new septum protection element. Changes were also applied to the septum diluter in the fast extraction channel in LSS4, leading to the other LHC ring and the CNGS facility. The requirements and the layout of the new LSS6 extraction channel will be described including a discussion of the design and performance of the installed septum diluters.

SPS slow extraction septa

CERN Multimedia

CERN PhotoLab

1979-01-01

SPS long straight section (LSS) with a series of 5 septum tanks for slow extraction (view in the direction of the proton beam). There are 2 of these: in LSS2, towards the N-Area; in LSS6 towards the W-Area. See also Annual Report 1975, p.175.

Stacks of SPS Dipole Magnets

CERN Multimedia

1974-01-01

Stacks of SPS Dipole Magnets ready for installation in the tunnel. The SPS uses a separated function lattice with dipoles for bending and quadrupoles for focusing. The 6.2 m long normal conducting dipoles are of H-type with coils that are bent-up at the ends. There are two types, B1 (total of 360) and B2 (384). Both are for a maximum field of 1.8 Tesla and have the same outer dimensions (450x800 mm2 vxh) but with different gaps (B1: 39x129 mm2, B2: 52x92 mm2) tailored to the beam size. The yoke, made of 1.5 mm thick laminations, consists of an upper and a lower half joined together in the median plane once the coils have been inserted.

Biodegradation test of SPS-LS blends as polymer electrolyte membrane fuel cells

International Nuclear Information System (INIS)

Putri, Zufira; Arcana, I Made

2014-01-01

Sulfonated polystyrene (SPS) can be applied as a proton exchange membrane fuel cell due to its fairly good chemical stability. In order to be applied as polymer electrolyte membrane fuel cells (PEMFCs), membrane polymer should have a good ionic conductivity, high proton conductivity, and high mechanical strength. Lignosulfonate (LS) is a complex biopolymer which has crosslinks and sulfonate groups. SPS-LS blends with addition of SiO 2 are used to increase the proton conductivity and to improve the mechanical properties and thermal stability. However, the biodegradation test of SPS-LS blends is required to determine whether the application of these membranes to be applied as an environmentally friendly membrane. In this study, had been done the synthesis of SPS, biodegradability test of SPS-LS blends with variations of LS and SiO 2 compositions. The biodegradation test was carried out in solid medium of Luria Bertani (LB) with an activated sludge used as a source of microorganism at incubation temperature of 37°C. Based on the results obtained indicated that SPS-LS-SiO 2 blends are more decomposed by microorganism than SPS-LS blends. This result is supported by analysis of weight reduction percentage, functional groups with Fourier Transform Infrared (FTIR) Spectroscopy, and morphological surface with Scanning Electron Microscopy (SEM)

A users view of the SPS and LEP control systems

International Nuclear Information System (INIS)

Bailey, R.

1992-01-01

Every accelerator has a control system; at present the SPS has two, both of which are needed to run the machine. Consequently a user of the SPS/LEP complex has to be concurrently familiar with three control systems. While this situation brings problems it allows, even forces, comparison between the different systems, which in turn enriches the user viewpoint. This paper assesses the SPS and LEP control systems from the point of view of the user, who may be an equipment specialist, operator, accelerator physicist or combinations thereof. (author)

Upgrade of the CERN SPS Extraction Protection Elements TPS

CERN Document Server

Borburgh, Jan; Barnes, Michael; Baud, Cedric; Fraser, Matthew; Kain, Verena; Maciariello, Fausto; Steele, Genevieve; Velotti, Francesco

2017-01-01

In 2006 the protection devices upstream of the septa in both extraction channels of the CERN SPS to the LHC were installed. Since then, new beam parameters have been proposed for the SPS beam towards the LHC in the framework of the LIU project. The mechanical parameters and assumptions on which these protection devices presently have been based, need validation before the new upgraded versions can be designed and constructed. The paper describes the design assumptions for the present protection device and the testing program for the TPSG4 at HiRadMat to validate them. Finally the requirements and the options to upgrade both extraction protection elements in the SPS are described.

The SPS was the second cross-border accelerator

CERN Multimedia

2004-01-01

In the Golden Jubilee article in the issue 25/2004 (14 June) we should have written that the SPS was the first big cross-border accelerator. In fact, the SPS was not the first cross-border accelerator: that title goes to the PS Booster which became operational in 1972. The PS Booster passes beams to the PS and to the ISOLDE facility. We are sorry for the mistake and thank our vigilant readers.

Physics at the AD/PS/SPS (1/4)

CERN Multimedia

CERN. Geneva

2012-01-01

Lecture 1: The CERN injector complex and beams for non-LHC physics. The various machines and beam lines in the CERN injector complex are presented, from the linacs to the SPS. Special emphasis is given to the beam lines at the PS and SPS machines: AD, North and East Areas, nTOF and CNGS and HiRadMad as well as the ion beams. A short outlook is given to possible future upgrades and projects.

Tune Resonance Phenomena in the SPS and related Machine Protection

CERN Document Server

Baer, Tobias; Elsen, E

2010-01-01

The Super Proton Synchrotron (SPS) at CERN, with a peak energy of 450 GeV, is at the top of the LHC preaccelerator complex. SPS is at present the accelerator with the largest stored beam energy worldwide of up to 2.5 MJ. In 2008, a fast equipment failure led to an uncontrolled loss of a high intensity beam at an integer tune resonance, which resulted in major damage of a main dipole. Experimental studies and simulations provide clear understanding of the beam dynamics at different SPS tune resonances, that can lead to a complete beam loss in as little as 3 turns. Dedicated experiments of fast failures of the main power converters reveal that the current interlock systems are much too slow for an adequate machine protection. A new position interlock system, which is currently in the commissioning phase, will counteract the vulnerability of the SPS.

The extant shore platform stromatolite (SPS facies association: a glimpse into the Archean?

Directory of Open Access Journals (Sweden)

A. Smith

2018-04-01

Full Text Available Shore platform stromatolites (SPS were first noted at Cape Morgan on the south-east African seaboard. Since then they have been found growing discontinuously in rocky peritidal zones along the entire southern African seaboard. They have also been found on the southwest Australian coast, at Giant's Causeway in Northern Ireland, and more recently at Harris on the Scottish Hebridean Atlantic coast. In this paper SPS occurrence and SPS potential as analogues for Precambrian fossil stromatolites, as well as potential stromatolite occurrences in shore platform regions on Mars, are assessed. Sub-horizontal surfaces promote stromatolite development, while tufa develops on cliffs and steep rocky surfaces. Tufa and stromatolites are end members of a spectrum dictated by coastal topography. Extant SPS occur on well indurated shore platforms in high wave energy settings, often around or near headlands. They can be associated with boulder beaches, boulder ridges, storm swash terraces, coastal dunes, and peat bogs. In contrast to other extant stromatolites, SPS are produced primarily by mineral precipitation, although minor trapping and binding stromatolites do occur. From a geological perspective, SPS develop in mildly transgressive siliciclastic settings in various climatic and tidal regimes. We suggest that SPS could be preserved in the geological record as micritic lenses on palaeo-shore platform surfaces. SPS share many features with Precambrian stromatolites and are a valid modern analogue despite the widely different atmospheric and oceanic conditions of the Archean. We suggest that terraces associated with former oceanic or lacustrine flooding surfaces on Mars are potential targets in the search for palaeo-SPS on Mars.

Biodegradation test of SPS-LS blends as polymer electrolyte membrane fuel cells

Energy Technology Data Exchange (ETDEWEB)

Putri, Zufira, E-mail: zufira.putri@gmail.com, E-mail: arcana@chem.itb.ac.id; Arcana, I Made, E-mail: zufira.putri@gmail.com, E-mail: arcana@chem.itb.ac.id [Inorganic and Physical Chemistry Research Groups, Faculty of Mathematics and Natural Sciences, Institut Teknologi Bandung, Bandung (Indonesia)

2014-03-24

Sulfonated polystyrene (SPS) can be applied as a proton exchange membrane fuel cell due to its fairly good chemical stability. In order to be applied as polymer electrolyte membrane fuel cells (PEMFCs), membrane polymer should have a good ionic conductivity, high proton conductivity, and high mechanical strength. Lignosulfonate (LS) is a complex biopolymer which has crosslinks and sulfonate groups. SPS-LS blends with addition of SiO{sub 2} are used to increase the proton conductivity and to improve the mechanical properties and thermal stability. However, the biodegradation test of SPS-LS blends is required to determine whether the application of these membranes to be applied as an environmentally friendly membrane. In this study, had been done the synthesis of SPS, biodegradability test of SPS-LS blends with variations of LS and SiO{sub 2} compositions. The biodegradation test was carried out in solid medium of Luria Bertani (LB) with an activated sludge used as a source of microorganism at incubation temperature of 37°C. Based on the results obtained indicated that SPS-LS-SiO{sub 2} blends are more decomposed by microorganism than SPS-LS blends. This result is supported by analysis of weight reduction percentage, functional groups with Fourier Transform Infrared (FTIR) Spectroscopy, and morphological surface with Scanning Electron Microscopy (SEM)

SPS in training for LHC

CERN Document Server

2003-01-01

On 8 and 9 September the new beam extraction system of the SPS and the downstream transfer line were successfully commissioned and tested. Using this extraction, a beam will be sent towards LHC in 2004 and to the CNGS facility in 2006.

The SPS acceleration system: travelling wave drift-tube structure for the CERN SPS

International Nuclear Information System (INIS)

Dome, G.

1976-01-01

The SPS accelerating structure is essentially a high energy proton linac, except for a small frequency swing during the acceleration cycle. It is operated almost CW with a travelling wave giving an energy gain around 0.1 MeV/m. The guide-lines for the design of such a structure are explained, and practical solutions are described. (author)

The environmental impact of SPS - A social view

International Nuclear Information System (INIS)

Canough, G.E.; Lehman, L.P.

1991-01-01

Prospective solar power satellite (SPS) systems entail extensive evaluation of real and perceived environmental impact, in virtue of their extremely high publicity profile. Attention is presently given to current understanding of SPS microwave power beaming system operations' effects on terrestrial communications and biological systems, as well as the associated consequences of a lengthy, heavy-payload launch program on space debris scenarios and stratospheric pollution by the launch vehicles' propellant combustion products. Education of the public in these issues is stressed. 7 refs

Search for the QCD critical point at SPS energies

CERN Document Server

Anticic, T.; Barna, D.; Bartke, J.; Betev, L.; Bialkowska, H.; Blume, C.; Boimska, B.; Botje, M.; Bracinik, J.; Buncic, P.; Cerny, V.; Christakoglou, P.; Chung, P.; Chvala, O.; Cramer, J.G.; Csato, P.; Dinkelaker, P.; Eckardt, V.; Fodor, Z.; Foka, P.; Friese, V.; Gal, J.; Gazdzicki, M.; Genchev, V.; Gladysz, E.; Grebieszkow, K.; Hegyi, S.; Hohne, C.; Kadija, K.; Karev, A.; Kikola, D.; Kolesnikov, V.I.; Kornas, E.; Korus, R.; Kowalski, M.; Kreps, M.; Laszlo, A.; Lacey, R.; van Leeuwen, M.; Levai, P.; Litov, L.; Lungwitz, B.; Makariev, M.; Malakhov, A.I.; Mateev, M.; Melkumov, G.L.; Mischke, A.; Mitrovski, M.; Mrowczynski, St.; Palla, G.; Panagiotou, A.D.; Petridis, A.; Peryt, W.; Pikna, M.; Pluta, J.; Prindle, D.; Puhlhofer, F.; Renfordt, R.; Roland, C.; Roland, G.; Rybczynski, M.; Rybicki, A.; Sandoval, A.; Schmitz, N.; Schuster, T.; Seyboth, P.; Sikler, F.; Sitar, B.; Skrzypczak, E.; Slodkowski, M.; Stefanek, G.; Stock, R.; Strabel, C.; Strobele, H.; Susa, T.; Szentpetery, I.; Sziklai, J.; Szuba, M.; Szymanski, P.; Trubnikov, V.; Utvic, M.; Varga, D.; Vassiliou, M.; Veres, G.I.; Vesztergombi, G.; Vranic, D.; Wlodarczyk, Z.; Wojtaszek-Szwarc, A.; Yoo, I.K.; Abgrall, N.; Aduszkiewicz, A.; Andrieu, B.; Anticic, T.; Antoniou, N.; Argyriades, J.; Asryan, A.G.; Blondel, A.; Blumer, J.; Boldizsar, L.; Bravar, A.; Brzychczyk, J.; Bubak, A.; Bunyatov, S.A.; Choi, K.-U.; Chung, P.; Cleymans, J.; Derkach, D.A.; Diakonos, F.; Dominik, W.; Dumarchez, J.; Engel, R.; Ereditato, A.; Feofilov, G.A.; Ferrero, A.; Gazdzicki, M.; Golubeva, M.; Grzeszczuk, A.; Guber, F.; Hasegawa, T.; Haungs, A.; Igolkin, S.; Ivanov, A.S.; Ivashkin, A.; Katrynska, N.; Kielczewska, D.; Kisiel, J.; Kobayashi, T.; Kolev, D.; Kolevatov, R.S.; Kondratiev, V.P.; Kowalski, S.; Kurepin, A.; Lacey, R.; Lyubushkin, V.V.; Majka, Z.; Marchionni, A.; Marcinek, A.; Maris, I.; Matveev, V.; Meregaglia, A.; Messina, M.; Mijakowski, P.; Montaruli, T.; Murphy, S.; Nakadaira, T.; Naumenko, P.A.; Nikolic, V.; Nishikawa, K.; Palczewski, T.; Planeta, R.; Popov, B.A.; Posiadala, M.; Przewlocki, P.; Rauch, W.; Ravonel, M.; Rohrich, D.; Rondio, E.; Rossi, B.; Roth, M.; Rubbia, A.; Sadovsky, A.; Sakashita, K.; Sekiguchi, T.; Seyboth, P.; Shibata, M.; Sissakian, A.N.; Sorin, A.S.; Staszel, P.; Stepaniak, J.; Strabel, C.; Stroebele, H.; Tada, M.; Taranenko, A.; Tsenov, R.; Ulrich, R.; Unger, M.; Vechernin, V.V.; Zipper, W.

2009-01-01

Lattice QCD calculations locate the QCD critical point at energies accessible at the CERN Super Proton Synchrotron (SPS). We present average transverse momentum and multiplicity fluctuations, as well as baryon and anti-baryon transverse mass spectra which are expected to be sensitive to effects of the critical point. The future CP search strategy of the NA61/SHINE experiment at the SPS is also discussed.

The SPS as accelerator of Pb$^{82+}$ ions

CERN Document Server

Faugier, A; Bailey, R; Blanchard, R R; Bohl, T; Brouzet, E; Burkhardt, H; Collier, Paul; Cornelis, Karel; de Rijk, G; Ferioli, F; Hilaire, A; Lamont, M; Linnecar, Trevor Paul R; Jonker, M; Niquille, C; Roy, G; Schmickler, Hermann

1996-01-01

In 1994 the CERN SPS was used for the first time to accelerate fully stripped ions of the Pb208 isotope from the equivalent proton momentum of 13 GeV/c to 400 GeV/c. In the CERN PS, which was used as injector, the lead was accelerated as Pb53+ ions and then fully stripped in the transfer line from PS to SPS. The radio frequency swing which is needed in order to keep the synchronism during acceleration is too big to have the SPS cavities deliver enough voltage for all frequencies. For that reason a new technique of fixed frequency acceleration was used. With this technique up to 70% of the injected beam could be captured and accelerated up to the extraction energy, the equivalent of 2.2 1010 charges. The beam was extracted over a 5 sec. long spill and was then delivered to different experiments at the same time.

Extraction systems of the SPS

CERN Multimedia

CERN PhotoLab

1973-01-01

A pair of prototype septum magnets for the extraction systems of the SPS. Each of the two extraction systems will contain eighteen of these septum magnets (eight with a 4 mm septum and ten with a 16 mm septum) mounted in pairs in nine vacuum tanks.

Prototype of cavity for lepton acceleration in the SPS

CERN Multimedia

CERN PhotoLab

1982-01-01

The SPS was to be the injector for LEP and had to accelerate the electrons and positrons delivered by the PS. This is a prototype of a 200 MHz, single-cell, standing-wave, cavity for lepton acceleration in the SPS. On top of the cavity, at the back, is the tetrode amplifier, the tuning mechanism is leaning towards the viewer. See also 8103523 and Annual Report 1981, p.114.

Prinsip Transparansi dalam Perjanjian TBT dan SPS

Directory of Open Access Journals (Sweden)

Dina Widyaputri Kariodimedjo

2012-02-01

Full Text Available Transparency principle in the TBT and SPS Agreement is implemented by notification. Its application is prepared by related agencies through the making of regulations, establishment of enquiry points, building capacity and infrastructure. It guarantees certainty, predictability and credibility of Indonesia in international trade, and its application should not undermine national trade policy. Prinsip transparansi dalam Perjanjian TBT dan SPS diterapkan melalui notifikasi. Penerapan prinsip ini dilakukan oleh instansi-instansi terkait melalui pembuatan peraturan, upaya terkait kelembagaan, SDM dan infrastruktur. Prinsip yang bertujuan menciptakan kepastian, konsistensi bagi perdagangan dan kredibilitas Indonesia dalam perdagangan internasional, harus dilakukan tanpa mengorbankan kepentingan untuk mengamankan kebijakan impor nasional.

SPS, preassembly of short straight sections

CERN Multimedia

1975-01-01

Short straight sections were preassembled with their vacuum chambers, ready for installation in the SPS. Here we see two, containing sextupoles for chromaticity adjustment. See also 7501017, 7501018, and Annual Report 1976, p.174.

SPS, short straight section with sextupole

CERN Multimedia

CERN PhotoLab

1975-01-01

Short straight sections were preassembled with their vacuum chambers, ready for installation in the SPS. This one contains a sextupole for chromaticity adjustment. See also 7501017, 7501009X, and Annual Report 1974, p.174.

The CERN SPS proton–antiproton collider

CERN Document Server

Schmidt, Rudiger

2016-01-01

One of CERN's most ambitious and successful projects was the search for the intermediate bosons, W and Z [1]. The accelerator part of the project relied on a number of innovations in accelerator physics and technology. The invention of the method of stochastic cooling and the extension by many orders of magnitude beyond the initial proof of principle demonstration allowed the construction of the Antiproton Accumulator. Major modifications to the 26 GeV PS complex and the conversion of the 300 GeV SPS, which had just started up as an accelerator, to a collider were required. The SPS collider had to master the beam–beam effect far beyond limits reached before and had to function in a tight symbiosis with the UA1 and UA2 experiments.

Simulation of e-cloud driven instability and its attenuation using a simulated feedback system in the CERN SPS

International Nuclear Information System (INIS)

Vay, J.-L.; Furman, M.A.

2010-01-01

Electron clouds have been shown to trigger fast growing instabilities on proton beams circulating in the SPS, and a feedback system to control the single-bunch instabilities is under active development. We present the latest improvements to the WARP-POSINST simulation framework and feedback model, and its application to the self-consistent simulations of two consecutive bunches interacting with an electron cloud in the SPS. Simulations using an idealized feedback system exhibit adequate mitigation of the instability providing that the cutoff of the feedback bandwidth is at or above 450 MHz. Artifacts from numerical noise of the injected distribution of electrons in the modeling of portions of bunch trains are discussed, and benchmarking of WARP against POSINST and HEADTAIL are presented.

Slow extraction at the SPS: extraction efficiency and loss reduction studies

CERN Document Server

Fraser, M A; Cavoto, G; Galluccio, F; Gilardoni, S; Goddard, B; Iacoangeli, F; Kain, V; Mirarchi, D; Montesano, S; Murtas, F; Petrucci, S; Redaelli, S; Roncarolo, F; Rossi, R; Scandale, W; Stoel, L S; Velott, F M

2017-01-01

Elevated activation levels in LSS2 were first reported dur-ing an intervention on the SPS extraction septum (ZS) inSeptember 2015. The increase was attributed to higher in-tensity Fixed Target (FT) operation and poorer extractionefficiency, and reported to the IEFC [1]. Since this eventthe awareness of the impact of slow extraction losses on theoperation and maintenance of the SPS has been heightened.This is particularly pertinent in light of tightening limits ondose to personnel and recent requests for increased intensi-ties, as well as ambitious future experimental proposals inthe North Area (NA), such as the SPS Beam Dump Facility(BDF) [2]. To follow up these issues the SPS Losses andActivation Working Group (SLAWG) was formed.The MD programme for 2016 was originally foreseen totest the faster spill on a 1.2 second flat-top for the BDF andbenchmarksimulationsoftheextractionprocess, butthiswasnot possible due to the restrictions imposed by the TIDVG.Nevertheless, during operational set-up and re-alignmentof...

Conditions and requirements for a potential application of solar power satellites /SPS/ for Europe

Energy Technology Data Exchange (ETDEWEB)

Westphal, W. (Berlin, Technische Universitaet, Berlin, West Germany); Ruth, J. (ESA, European Space Research and Technology Centre, Noordwijk, Netherlands)

1980-12-01

The potential problems of a future introduction of Solar Power Satellites (SPS) as baseload power plants for Western European countries are considered, emphasizing the differences of SPS utilization in Europe compared with that in the USA as a result of geographical, orbital organizational, and industrial conditions. If estimated SPS safety zone areas are required, then the SPS system incorporating the 2.45 GHz microwave power transmission appears crucial for utilization in Western Europe in order to eliminate the large rectenna area requirements of an SPS 5 GW power system. A frequency variation of up to 5 or 10 GHz, and the application of either laser power transmission or solid state devices which could alleviate rectenna siting problems and restrictions on the use of the geosynchronous orbit are discussed.

Coupling and Vertical Dispersion Correction in the SPS

CERN Document Server

Aiba, M; Franchi, A; Tomas, R; Vanbavinckhove, G

2010-01-01

Consolidation of the coupling correction scheme in the LHC is challenged by a missing skew quadrupole family in Sector 3-4 at the start-up in 2009-2010. Simultaneous coupling and vertical dispersion correction using vertical orbit bumps at the sextupoles, was studied by analyzing turn-byturn data. This scheme was tested in the CERN SPS where the optical structure of arc cells is quite similar to the LHC. In the SPS, horizontal and vertical beam positions are measured separately with single plane BPMs, thus a technique to construct ”pseudo double plane BPM” is also discussed.

Studies on the QCD Phase Diagram at SPS and FAIR

International Nuclear Information System (INIS)

Blume, Christoph

2013-01-01

A review of results of the energy scan program at the CERN-SPS by the NA49 experiment is given. Presented are observables related to the search for a critical point in the QCD phase diagram and for the onset of deconfinement. Furthermore, the ongoing experimental program of NA61 at the CRRN-SPS and the plans of the CBM experiment at FAIR are discussed.

Event-by-event fluctuations at SPS

CERN Document Server

Appelshauser, Harald; Adamova, D.; Agakichiev, G.; Belaga, V.; Braun-Munzinger, P.; Castillo, A.; Cherlin, A.; Damjanovic, S.; Dietel, T.; Dietrich, L.; Drees, A.; Esumi, S.I.; Filimonov, K.; Fomenko, K.; Fraenkel, Z.; Garabatos, C.; Glassel, P.; Hering, G.; Holeczek, J.; Kushpil, V.; Lenkeit, B.; Ludolphs, W.; Maas, A.; Marn, A.; Milosevic, J.; Milov, A.; Miskowiec, D.; Panebrattsev, Yu.; Petchenova, O.; Petracek, V.; Pfeiffer, A.; Rak, J.; Ravinovich, I.; Rehak, P.; Schmitz, W.; Schukraft, J.; Sedykh, S.; Shimansky, S.; Slvova, J.; Stachel, J.; Sumbera, M.; Tilsner, H.; Tserruya, Itzhak; Wessels, J.P.; Wienold, T.; Windelband, B.; Wurm, J.P.; Xie, W.; Yurevich, S.; Yurevich, V.; Appelshauser, Harald; Sako, Hiro

2005-01-01

Results on event-by-event fluctuations of the mean transverse momentum and net charge in Pb-Au collisions, measured by the CERES Collaboration at CERN-SPS, are presented. We discuss the centrality and beam energy dependence and compare our data to cascade calculations.

Installation in the SPS tunnel

CERN Multimedia

1974-01-01

The SPS tunnel is 6910 m in circumference and has a cross section of 4 m inner diameter. It is situated at an elevation of 400 m above sea level at a depth below the surface varying between 23 and 65 m. Its walls are lined with a concrete shell of about 30 cm thickness. See also 7410043X

Transverse mode coupling instability for leptons in the CERN SPS

Energy Technology Data Exchange (ETDEWEB)

Linnecar, T; Shaposhnikova, E N [European Organization for Nuclear Research, Geneva (Switzerland)

1996-08-01

The intensity of leptons accelerated in the SPS machine is limited by a vertical transverse instability. The results of measurements of the thresholds for this transverse instability are compared with theoretical predictions for different broad band impedance models of the SPS. The threshold intensities found for the transverse instability and the position of the losses in the cycle enable the parameters of the broadband resonant impedance to be specified. (author)

The capabilities of monochromatic EC neutrino beams with the SPS upgrade

International Nuclear Information System (INIS)

Espinoza, C; Bernabeu, J

2008-01-01

The goal for future neutrino facilities is the determination of the U(e3) mixing and CP violation in neutrino oscillations. This will require precision experiments with a very intense neutrino source and energy control. With this objective in mind, the creation of monochromatic neutrino beams from the electron capture decay of boosted ions by the SPS of CERN has been proposed. We discuss the capabilities of such a facility as a function of the energy of the boost and the baseline for the detector. We conclude that the SPS upgrade to 1000 GeV is crucial to reach a better sensitivity to CP violation iff it is accompanied by a longer baseline. We compare the physics potential for two different configurations: I) γ = 90 and γ = 195 (maximum achievable at present SPS) to Frejus; II) γ = 195 and γ = 440 (maximum achievable at upgraded SPS) to Canfranc. The main conclusion is that, whereas the gain in the determination of U(e3) is rather modest, setup II provides much better sensitivity to CP violation

The capabilities of monochromatic EC neutrino beams with the SPS upgrade

Science.gov (United States)

Espinoza, C.; Bernabéu, J.

2008-05-01

The goal for future neutrino facilities is the determination of the U(e3) mixing and CP violation in neutrino oscillations. This will require precision experiments with a very intense neutrino source and energy control. With this objective in mind, the creation of monochromatic neutrino beams from the electron capture decay of boosted ions by the SPS of CERN has been proposed. We discuss the capabilities of such a facility as a function of the energy of the boost and the baseline for the detector. We conclude that the SPS upgrade to 1000 GeV is crucial to reach a better sensitivity to CP violation iff it is accompanied by a longer baseline. We compare the physics potential for two different configurations: I) γ = 90 and γ = 195 (maximum achievable at present SPS) to Frejus; II) γ = 195 and γ = 440 (maximum achievable at upgraded SPS) to Canfranc. The main conclusion is that, whereas the gain in the determination of U(e3) is rather modest, setup II provides much better sensitivity to CP violation.

European sail tower SPS [Solar Power Satellite] concept

Energy Technology Data Exchange (ETDEWEB)

Seboldt, W.; Leipold, M.; Hanowski, N. [Institute of Space Sensor Technology and Planetary Exploration, Cologne (Germany). German Aerospace Center; Klimke, M. [HOPE Worldwide Deutschland, Berlin (Germany)

2001-06-01

Based on a DLR-study in 1998/99 on behalf of ESA/ESTEC called ''System Concepts, Architectures and Technologies for Space Exploration and Utilization (SE and U)'' a new design for an Earth-orbiting Solar Power Satellite (SPS) has been developed. The design is called ''European Sail Tower SPS'' and consists mainly of deplorable sail-like structures derived from the ongoing DLR/ESA solar sail technology development activity. Such an SPS satellite features an extremely light-weight and large tower-like orbital system and could supply Europe with significant amounts of electrical power generated by photovoltaic cells and subsequently transmitted to earth via microwaves. In order to build up the sail tower, 60 units - each consisting of a pair of square-shaped sails - are moved from LEO to GEO with electric propulsion and successively assembled in GEO robotically on a central strut. Each single sail has dimensions of 150 m x 150 m and is automatically deployed, using four diagonal lightweight carbon fiber (CFRP) booms which are initially rolled up on a central hub. The electric thrusters for the transport to GEO could also be used for orbit and attitude control of the assembled tower which has a total length of about 15 km and would be mainly gravity gradient stabilized. Employing thin film solar cell technology, each sail is used as a solar array and produces an electric power in orbit of about 3.7 MW{sub e}. A microwave antenna with a diameter of 1 km transmits the power to a 10 km rectenna on the ground. The total mass of this 450 MW SPS is about 2100 tons. First estimates indicate that the costs for one kWh delivered in this way could compete with present day energy costs, if launch costs would decrease by two orders of magnitude. Furthermore, mass production and large numbers of installed SPS systems must be assumed in order to lower significantly the production costs and to reduce the influence of the expensive technology

Academic Training Lecture Regular Programme: Physics at the AD/PS/SPS

CERN Multimedia

2012-01-01

Physics at the AD/PS/SPS (1/4), by Lau Gatignon (CERN).   Monday, June 18, 2012 from 11:00 to 12:00 (Europe/Zurich) at CERN ( 222-R-001 - Filtration Plant )   Lecture 1: The CERN injector complex and beams for non-LHC physics. The various machines and beam lines in the CERN injector complex are presented, from the linacs to the SPS. Special emphasis is given to the beam lines at the PS and SPS machines: AD, North and East Areas, nTOF and CNGS and HiRadMad as well as the ion beams. A short outlook is given to possible future upgrades and projects.   More information here.  

Tune resonance phenomena in the SPS and machine protection via fast position interlocking

CERN Document Server

Baer, T; Bogey, T; Wenninger, J

2010-01-01

The Super Proton Synchrotron (SPS) at CERN with a peak energy of 450GeV is at the top of the LHC preaccelerator-complex. Apart from LHC, SPS is with Tevatron the accelerator with the largest stored beam energy, up to 2.5MJ. The SPS has a known vulnerability to fast equipment failures that led to an uncontrolled loss of a high intensity beam in 2008, which resulted in major damage of a main dipole. The beam loss was caused by a fast tune decrease towards an integer resonance. Simulations and distinct experimental studies provide clear understanding of the beam dynamics at different SPS tune resonances. Diverging closed orbit oscillations, dispersion explosion and abrupt increased beta-beating are the driving effects leading to a complete beam loss in as little as 3 turns (70us). Dedicated experiments of fast failures of the main power converters reveal that the current interlock systems are much too slow for an adequate machine protection. To counteract the vulnerability of the SPS, current research focuses on...

SPS transverse beam scraping and LHC injection losses

CERN Document Server

Drosdal, L; Bartmann, W; Bracco, C; Cornelis, K; Goddard, B; Meddahi, M; Veyrunes, E

2012-01-01

Machine protection sets strict requirements for the quality of the injected beam, in particular in the transverse plane. Losses at aperture restrictions and protection elements have to be kept at a minimum. Particles in the beam tails are lost at the tight transfer line collimators and can trigger the LHC beam abort system. These particles have to be removed by scrapers in the vertical and horizontal plane in the SPS. Scraping has become vital for high intensity LHC operation. This paper shows the dependence of injection quality on the SPS scraping and discusses an improved scraper setting up strategy for better reproducibility with the current scraper system.

Preliminary assessment of the environmental impacts of the Satellite Power System (SPS)

International Nuclear Information System (INIS)

Halverson, S.L.; Rote, D.M.; Rush, C.M.; Davis, K.; White, M.; Cahill, D.F.

1978-01-01

The impact of the Satellite Power System (SPS) Microwave Power Transmission System (MPTS) as well as impacts related to other elements of the total SPS on the environment are being determined. The goal of these programs is to advance the state of knowledge by the year 1980 to the point where an assessment can be made of the probability and severity of the impacts of the SPS. Assessments will be made of the effects on the health and safety of the public, and occupationally involved personnel, and the ecology; the upper and lower atmosphere including climatological impacts; and on communications systems including electromagnetic compatibility, the effects of microwave heating of the ionosphere and magnetosphere, and the effects of F-layer depletion by launch vehicle and transport vehicle effluents. If the assessment indicates that the impacts are acceptable or that feasible mitigating strategies can be implemented and if other related assessments (the impact on society and a competitive comparison of the SPS with other energy alternatives) are favorable, a decision may be made to implement the development of the SPS related technologies. This paper identifies postulated effects and summarizes the research efforts to determine whether or not these effects will occur

SPS Ion Induced Desorption Experiment

CERN Multimedia

Maximilien Brice

2003-01-01

This experiment will give a study about the induced desorption from heavy ion (Indium ion run from week 45 in SPS T4-H8 area) impacting LHC type graphite collimator. 4 different samples are located in the 4 chambers 90° one to each other: pure graphite, graphite with copper coating, graphite with NEG coating, 316LN stainless steal (reference).

The New Control and Interlock System for the SPS Main Power Converters

CERN Document Server

Denis, B; Mugnier, C; Varas, J

1999-01-01

The Control and Interlock System (CIS) of the SPS main power converters was designed in the mid-70s and became increasingly difficult to maintain. A new system based on Programmable Logic Controllers has been developed by an external contractor in close collaboration with CERN. The system is now operational and fully integrated in the SPS/LEP control infrastructure. The CIS is the first major contracted industrial solution used to control accelerator equipment directly involved in the production of particle beams at CERN. This paper gives an overview of the SPS main power converter installation and describes both the contractual and technical solution adopted for the CIS. It first explains how the system was specified and how the contractual relationship was defined to respect CERN’s purchasing rules and the operational requirements of the SPS accelerator. The architectural design of the new system is presented with special emphasis on how the conflict between safety and availability has been addressed.

Direct Numerical Modeling of E-Cloud Driven Instability of a Bunch Train in the CERN SPS

International Nuclear Information System (INIS)

Vay, J.-L.; Furman, M.A.; Venturini, M.

2011-01-01

The simulation package WARP-POSINST was recently upgraded for handling multiple bunches and modeling concurrently the electron cloud buildup and its effect on the beam, allowing for direct self-consistent simulation of bunch trains generating, and interacting with, electron clouds. We have used the WARP-POSINST package on massively parallel supercomputers to study the buildup and interaction of electron clouds with a proton bunch train in the CERN SPS accelerator. Results suggest that a positive feedback mechanism exists between the electron buildup and the e-cloud driven transverse instability, leading to a net increase in predicted electron density. Electron clouds have been shown to trigger fast growing instabilities on proton beams circulating in the SPS and other accelerators. So far, simulations of electron cloud buildup and their effects on beam dynamics have been performed separately. This is a consequence of the large computational cost of the combined calculation due to large space and time scale disparities between the two processes. We have presented the latest improvements of the simulation package WARP-POSINST for the simulation of self-consistent ecloud effects, including mesh refinement, and generation of electrons from gas ionization and impact at the pipe walls. We also presented simulations of two consecutive bunches interacting with electrons clouds in the SPS, which included generation of secondary electrons. The distribution of electrons in front of the first beam was initialized from a dump taken from a preceding buildup calculation using the POSINST code. In this paper, we present an extension of this work where one full batch of 72 bunches is simulated in the SPS, including the entire buildup calculation and the self-consistent interaction between the bunches and the electrons.

The new control system of the SPS injection kicker

CERN Document Server

Antoine, A; Marchand, A; Verhagen, H

2002-01-01

The SPS accelerator will be used as injector for the LHC and has to be adapted to the LHC requirements. The tight specification on beam blow-up and bunch spacing in the SPS has required an upgrade program of the SPS injection kicker in order to obtain a reduction of the magnetic field ripple to less than ± 0.5% and of the magnet current rise time to less than 145 ns. In this context, the slow control part has been entirely rebuilt on the basis of off-the-shelf industrial components. A hierarchical architecture based on a SIEMENS S7-400 master programmable logic controller interconnected through PROFIBUS-DP to S7-300 deported and decentralised I/Os has been implemented. Integration of in-house specific G-64 hardware systems inside this industrial environment has been done through a PROFIBUS-DP to G-64 intelligent interface based on an OEM fieldbus mezzanine board on one side and an FPGA implementing the required functionality on the other. Simultaneously, the fast timing system has been completely reshuffled ...

Assessors for communication skills: SPs or healthcare professionals?

Science.gov (United States)

Liew, Siaw-Cheok; Dutta, Susmita; Sidhu, Jagmohni Kaur; De-Alwis, Ranjit; Chen, Nicole; Sow, Chew-Fei; Barua, Ankur

2014-07-01

The complexity of modern medicine creates more challenges for teaching and assessment of communication skills in undergraduate medical programme. This research was conducted to study the level of communication skills among undergraduate medical students and to determine the difference between simulated patients and clinical instructors' assessment of communication skills. This comparative study was conducted for three months at the Clinical Skills and Simulation Centre of the International Medical University in Malaysia. The modified Calgary-Cambridge checklist was used to assess the communication skills of 50 first year and 50 second year medical students (five-minutes pre-recorded interview videos on the scenario of sore throat). These videos were reviewed and scored by simulated patients (SPs), communication skills instructors (CSIs) and non-communication skills instructors (non-CSIs). Better performance was observed among the undergraduate medical students, who had formal training in communication skills with a significant difference in overall scores detected among the first and second year medical students (p = 0.0008). A non-significant difference existed between the scores of SPs and CSIs for Year 1 (p = 0.151). The SPs could be trained and involved in assessment of communication skills. Formal training in communication skills is necessary in the undergraduate medical programme.

MODELLING SLOW EXTRACTION INDUCED RADIOACTIVITY IN SPS LSS2

CERN Document Server

Araujo Martinez, Aurora Cecilia; CERN. Geneva. TE Department

2017-01-01

The Accelerator and Beam Transfer (ABT) group is investigating the impact of recent proposals to extract higher proton intensities to Fixed Target experiments at the SPS. The 400 GeV high-energy proton beam is typically extracted over a few seconds using a resonant slow-extraction technique that induces small but unavoidable beam losses on the extraction equipment in SPS LSS2. In this report, the induced radioactivity for 2016-2017 is used to predict future activation levels and cool-down times, using a past intervention as a reference to predict dose to the personnel carrying-out maintenance of the accelerator.

Arabidopsis thaliana sucrose phosphate synthase (sps) genes are expressed differentially in organs and tissues, and their transcription is regulated by osmotic stress.

Science.gov (United States)

Solís-Guzmán, María Gloria; Argüello-Astorga, Gerardo; López-Bucio, José; Ruiz-Herrera, León Francisco; López-Meza, Joel Edmundo; Sánchez-Calderón, Lenin; Carreón-Abud, Yazmín; Martínez-Trujillo, Miguel

2017-11-01

Sucrose is synthesized from UDP-Glc and Fru-6-phosphate via the activity of sucrose-phosphate synthase (SPS) enzymes, which produce Suc-6-phosphate. Suc-6-phosphate is rapidly dephosphorylated by phosphatases to produce Suc and inorganic phosphate. Arabidopsis has four sps genes encoding SPS enzymes. Of these enzymes, AtSPS1F and AtSPS2F have been grouped with other dicotyledonous SPS enzymes, while AtSPS3F and AtSPS4F are included in groups with both dicotyledonous and monocotyledonous SPS enzymes. In this work, we generated Arabidopsis thaliana transformants containing the promoter region of each sps gene fused to gfp::uidA reporter genes. A detailed characterization of expression conferred by the sps promoters in organs and tissues was performed. We observed expression of AtSPS1F, AtSPS2F and AtSPS3F in the columella roots of the plants that support sucrose synthesis. Hence, these findings support the idea that sucrose synthesis occurs in the columella cells, and suggests that sucrose has a role in this tissue. In addition, the expression of AtSPS4F was identified in embryos and suggests its participation in this developmental stage. Quantitative transcriptional analysis of A. thaliana plants grown in media with different osmotic potential showed that AtSPS2F and AtSPS4F respond to osmotic stress. Copyright © 2017 Elsevier B.V. All rights reserved.

A Beam Quality Monitor for LHC Beams in the SPS

CERN Document Server

Papotti, G

2008-01-01

The SPS Beam Quality Monitor (BQM) system monitors the longitudinal parameters of the beam before extraction to the LHC to prevent losses and degradation of the LHC luminosity by the injection of low quality beams. It is implemented in two priority levels. At the highest level the SPS-LHC synchronization and global beam structure are verified. If the specifications are not met, the beam should be dumped in the SPS before extraction. On the second level, individual bunch position, length and stability are checked for beam quality assessment. Tolerances are adapted to the mode of operation and extraction to the LHC can also be inhibited. Beam parameters are accessed by acquiring bunch profiles with a longitudinal pick up and fast digital oscilloscope. The beam is monitored for instabilities during the acceleration cycle and thoroughly checked a few ms before extraction for a final decision on extraction interlock. Dedicated hardware and software components implementing fast algorithms are required. In this pape...

Satellite Power Systems (SPS) concept definition study, exhibit C. Volume 2, part 2: System engineering, cost and programmatics

Science.gov (United States)

Hanley, G. M.

1979-01-01

Volume 2, Part 2, of a seven volume Satellite Power Systems (SPS) report is presented. Part 2 covers cost and programmatics and is divided into four sections. The first section gives illustrations of the SPS reference satellite and rectenna concept, and an overall scenario for SPS space transportation involvement. The second section presents SPS program plans for the implementation of PHASE C/D activities. These plans describe SPS program schedules and networks, critical items of systems evolution/technology development, and the natural resources analysis. The fourth section presents summary comments on the methods and rationale followed in arriving at the results documented. Suggestions are also provided in those areas where further analysis or evaluation will enhance SPS cost and programmatic definitions.

Self-Consistant Numerical Modeling of E-Cloud Driven Instability of a Bunch Train in the CERN SPS

International Nuclear Information System (INIS)

Vay, J.-L.; Furman, M.A.; Secondo, R.; Venturini, M.; Fox, J.D.; Rivetta, C.H.

2010-01-01

The simulation package WARP-POSINST was recently upgraded for handling multiple bunches and modeling concurrently the electron cloud buildup and its effect on the beam, allowing for direct self-consistent simulation of bunch trains generating, and interacting with, electron clouds. We have used the WARP-POSINST package on massively parallel supercomputers to study the growth rate and frequency patterns in space-time of the electron cloud driven transverse instability for a proton bunch train in the CERN SPS accelerator. Results suggest that a positive feedback mechanism exists between the electron buildup and the e-cloud driven transverse instability, leading to a net increase in predicted electron density. Comparisons to selected experimental data are also given. Electron clouds have been shown to trigger fast growing instabilities on proton beams circulating in the SPS and other accelerators. So far, simulations of electron cloud buildup and their effects on beam dynamics have been performed separately. This is a consequence of the large computational cost of the combined calculation due to large space and time scale disparities between the two processes. We have presented the latest improvements of the simulation package WARP-POSINST for the simulation of self-consistent ecloud effects, including mesh refinement, and generation of electrons from gas ionization and impact at the pipe walls. We also presented simulations of two consecutive bunches interacting with electrons clouds in the SPS, which included generation of secondary electrons. The distribution of electrons in front of the first beam was initialized from a dump taken from a preceding buildup calculation using the POSINST code. In this paper, we present an extension of this work where one full batch of 72 bunches is simulated in the SPS, including the entire buildup calculation and the self-consistent interaction between the bunches and the electrons. Comparisons to experimental data are also given.

Successful test of SPS-to-LHC beamline

CERN Multimedia

Maximilien Brice

2004-01-01

On 23 October there was great excitement in the Prevessin control room when, on the first attempt, a beam passed over 2.5 km down the new SPS-to-LHC transfer line, TI8, to within a few metres of the LHC tunnel.

SPS: scrubbing or coating ?

CERN Document Server

Jimenez, J M

2012-01-01

The operation of the SPS with high intensity bunched beams is limited by the electron cloud building-up in both the arcs and long straight sections. Two consolidation options have been considered: mitigation of the electron cloud using coatings or relying, as before, on the scrubbing runs. A status report on both options will be given with a particular emphasis on measurements plans for 2012 and pending issues. The testing needs, corresponding beam parameters and MD time in 2012 will be addressed. The criteria for the decision making and the corresponding schedule will be discussed.

SPS Internship: Working With Physics To Go

Science.gov (United States)

Hancock, Logan

2008-10-01

The Physics To Go website (www.physicstogo.com) is one of many collections of ComPADRE, an online library of electronic resources devoted to physics and astronomy education, funded by the National Science Foundation. Physics To Go, produced by the American Physical Society (APS), is a collection focused on informal physics learning, targeted towards self-motivated learners and the general public. My contributions to the site this summer consisted of obtaining useful materials to add to the collection and working to update the homepage's ``mini-magazine'' every two weeks. I was selected for this position at APS by the Society of Physics Students (SPS) summer internship program, hosted by the American Institute of Physics (AIP) in College Park, MD. This internship is presented to a number of physics undergraduates each year and offers opportunities in research and science policy/outreach positions at SPS, APS, AAPT, NASA, and NIST.

Search for Heavy Neutral Leptons at the SPS

CERN Document Server

Jacobsson, R

2013-01-01

A minimal extension of the Standard Model with three right-handed singlet Majorana leptons with masses below the Fermi scale (vMSM) allows incorporating a mechanism to generate the baryon asymmetry of the Universe, account for the pattern of small neutrino masses and oscillations, and potentially provide a Dark Matter candidate. This avoids introducing new energy scales between the Fermi scale and the Planck scale, the lack of which has also been shown to be compatible with the mass of the recently discovered Higgs boson. Considerations based on cosmological constraints and based on the data on neutrino oscillations favour a range of masses and couplings for these new heavy neutral leptons (HNL) which is largely accessible to experimental verification or falsification. This paper outlines a proposal for a new fixed-target experiment at the CERN SPS to search for the HNLs, together with an introduction to the theoretical motivation, a description of the experimental setup with the associated beam line and det...

Satellite Power Systems (SPS) concept definition study, exhibit C. Volume 2, part 2: System engineering, cost and programmatics, appendixes

Science.gov (United States)

Hanley, G. M.

1979-01-01

Appendixes for Volume 2 (Part 2) of a seven volume Satellite (SPS) report are presented. The document contains two appendixes. The first is a SPS work breakdown structure dictionary. The second gives SPS cost estimating relationships and contains the cost analyses and a description of cost elements that comprise the SPS program.

Considerations on a new fast extraction kicker concept for SPS

CERN Document Server

Barnes, M

2010-01-01

An alternative extraction kicker concept is investigated for the SPS, based on open C-type kickers and a fast-bumper system. The beam is moved into the kicker gap some tens of ms before extraction. The concept is illustrated in detail with the LSS4 extraction from the SPS – very similar parameters and considerations apply to LSS6. A similar concept could also be conceived for injection but is more difficult due to the larger beam size. The technical issues are presented and the potential impact on the machine impedance outlined.

Physics at the SPS

Science.gov (United States)

Gatignon, L.

2018-05-01

The CERN Super Proton Synchrotron (SPS) has delivered a variety of beams to a vigorous fixed target physics program since 1978. In this paper, we restrict ourselves to the description of a few illustrative examples in the ongoing physics program at the SPS. We will outline the physics aims of the COmmon Muon Proton Apparatus for Structure and Spectroscopy (COMPASS), north area 64 (NA64), north area 62 (NA62), north area 61 (NA61), and advanced proton driven plasma wakefield acceleration experiment (AWAKE). COMPASS studies the structure of the proton and more specifically of its spin. NA64 searches for the dark photon A', which is the messenger for interactions between normal and dark matter. The NA62 experiment aims at a 10% precision measurement of the very rare decay K+ → π+νν. As this decay mode can be calculated very precisely in the Standard Model, it offers a very good opportunity to look for new physics beyond the Standard Model. The NA61/SHINE experiment studies the phase transition to Quark Gluon Plasma, a state in which the quarks and gluons that form the proton and the neutron are de-confined. Finally, AWAKE investigates proton-driven wake field acceleration: a promising technique to accelerate electrons with very high accelerating gradients. The Physics Beyond Colliders study at CERN is paving the way for a significant and diversified continuation of this already rich and compelling physics program that is complementary to the one at the big colliders like the Large Hadron Collider.

Dilution kicker for the SPS beam dump

CERN Multimedia

1974-01-01

In order to reduce thermal stress on the SPS dump material, the fast-ejected beam was swept horizontally across the dump. This was done with the "dilution kicker" MKDH, still in use at the time of writing. The person on the left is Manfred Mayer. See also 7404072X.

SPS: scrubbing or coating?

International Nuclear Information System (INIS)

Jimenez, J.M.

2012-01-01

The operation of the SPS with high intensity bunched beams is limited by the electron cloud building-up in both the arcs and long straight sections. Two consolidation options have been considered: suppression of the electron cloud build-up using coatings or relying, as before, on the scrubbing mitigation. A status report on both options will be given with a particular emphasis on measurements plans for 2012 and pending issues. The testing needs, corresponding beam parameters and MD time in 2012 will be addressed. The criteria for the decision making and the corresponding schedule will be discussed. (author)

Design of a high-precision fast wire scanner for the SPS at CERN

CERN Document Server

Veness, R; Dehning, B; Emery, J; Herranz Alvarez, J; Koujili, M; Samuelsson, S; Sirvent, J-L

2012-01-01

Studies are going on of a new wire scanner concept. All moving parts are inside the beam vacuum and it is specified for use in all the machines across the CERN accelerator complex. Key components have been developed and tested. Work is now focussing on the installation of a prototype for test in the Super Proton Synchrotron (SPS) accelerator. This article presents the specification of the device and constraints on the design for integration in the different accelerators at CERN. The design issues of the mechanical components are discussed and optimisation work shown. Finally, the prototype design, integrating the several components into the vacuum tank is presented.

Comparative studies on mechanical properties of WC-Co composites sintered by SPS and conventional techniques

Directory of Open Access Journals (Sweden)

Pristinskiy Yuri

2017-01-01

Full Text Available Spark plasma sintering (SPS is an extremely fast solidification technique for compounds that are difficult to sinter within the material group metals, ceramics, or composites thereof, SPS uses a uniaxial pressure and a very rapid heating cycle to consolidate these materials. With SPS the main benefit is the ability to control the WC grain size due to the short sintering times at high temperature. Additionally, its allows to avoid negative reactions between WC and cobalt and to minimize the formation of undesirable phases in sintered composites. The WC-6wt.% Co cermet prepared by SPS processing achieves the enhanced mechanical properties with the hardness of 18.3 GPa and the fracture toughness of 15.5 MPa·m1/2 in comparison to standard reference tungsten carbide/cobalt material.

Evolution of the SPS Power Converter Controls towards the LHC Era

CERN Document Server

Brazier, J.C.L.; Semanaz, P.

2001-01-01

By the end of the nineties, the power converter control system (Mugef) of the CERN proton accelerator (SPS) had undergone a complete modernization. This resulted in newly developed hardware for function generation, measurement and I/O in a VME environment, under the LynxOS real-time operating system. This has provided a platform on which extensions can be developed for future operation in the Large Hadron Collider (LHC) era. This paper describes some of these extensions, in particular a fast Surveillance and Interlock system for monitoring the power converter output currents. This will be mandatory for the safe operation of the SPS transfer lines TI2 & TI8 to LHC and for similar applications in the future. The strategies employed to cope with various failure modes of the power converters and the timely activation of the interlock are outlined. The new SPS controls infrastructure now under development, will give rise to new modes of operation for the Mugef systems. Integration with the proposed middleware ...

The SPS Individual Bunch Measurement System

CERN Document Server

Guerrero, A; Jones, R; Savioz, J J

2001-01-01

The Individual Bunch Measurement System (IBMS) allows the intensity of each bunch in an LHC batch to be the measured both in the PS to SPS transfer lines and in the SPS ring itself. The method is vased on measuring the peak and valley of the analogue signal supplied by a Fast Beam Current Transformer at a frequency of 40 MHz. A 12 bit acquisition system is required to obtain a 1% resolution for the intensity range of 5X10`9 to 1.7X10`11 protons per bunch, corresponding to the pilot and ultimate LHC bunch intensities. The acquisition selection and external trigger adjustment system is driven by the 200MHz RF, which is distributed using a single-mode fibre-optic link. A local oscilloscope, controlled via a GPIB interface, allows the remote adjustment of the timing signals. The low-level software consists of a real-time task and a communication server run on a VME Power PC, which is accessed using a graphical user interface. This paper describes the system as a whole and presents some recent uses and results fro...

Monitoring the extracted proton beam at the SPS

CERN Multimedia

CERN PhotoLab

1977-01-01

Fluorescent screens in front of the target positions allow a precise adjustement in front of them. A similar photo was recorded at the beam dump at the beam injection into the SPS, see Weekly Bulletin of April 1976.

Produced Water Treatment Using the Switchable Polarity Solvent Forward Osmosis (SPS FO) Desalination Process: Preliminary Engineering Design Basis

Energy Technology Data Exchange (ETDEWEB)

Wendt, Daniel; Adhikari, Birendra; Orme, Christopher; Wilson, Aaron

2016-05-01

Switchable Polarity Solvent Forward Osmosis (SPS FO) is a semi-permeable membrane-based water treatment technology. INL is currently advancing SPS FO technology such that a prototype unit can be designed and demonstrated for the purification of produced water from oil and gas production operations. The SPS FO prototype unit will used the thermal energy in the produced water as a source of process heat, thereby reducing the external process energy demands. Treatment of the produced water stream will reduce the volume of saline wastewater requiring disposal via injection, an activity that is correlated with undesirable seismic events, as well as generate a purified product water stream with potential beneficial uses. This paper summarizes experimental data that has been collected in support of the SPS FO scale-up effort, and describes how this data will be used in the sizing of SPS FO process equipment. An estimate of produced water treatment costs using the SPS FO process is also provided.

Measurements on the SPS 200 MHz Travelling Wave Cavity towards an Impedance Model

CERN Document Server

Roggen, Toon; Caspers, Fritz; Vollinger, Christine; CERN. Geneva. ATS Department

2016-01-01

This note discusses the contribution of the SPS 200 MHz TWC (Travelling Wave Cavity) to the SPS longitudinal impedance model. The measurement method and setup is briefly explained and a comparison with simulations is discussed for both the fundamental pass band (FPB) as well as the Higher Order Modes (HOMs). In addition a number of improvements to the measurement setup are discussed.

From SPS to relativistic heavy-ion collider

Indian Academy of Sciences (India)

higher temperature, longer lifetime) for the study of quark matter. The advent ... A prominent topic of interest is the identification of thermal radiation emitted from the collision ... List of measurements at the CERN SPS. Dileptons .... There is consensus that a simple superposition of pp collisions cannot explain the data and that ...

Experiment NA57 at the CERN SPS

Czech Academy of Sciences Publication Activity Database

Antinori, F.; Balada, A.; Barbera, R.; Píška, Karel; Staroba, Pavel; Závada, Petr

1999-01-01

Roč. 25, - (1999), s. 473-479 ISSN 0954-3899 Institutional research plan: CEZ:AV0Z1010920 Keywords : NA57 * production of strange, multistrange particles * baryons, antibaryons * ultrarelativistic nucleus - nucleus collisions * SPS * strangeness enhancement * number of participants Subject RIV: BF - Elementary Particles and High Energy Physics Impact factor: 1.620, year: 1999

Wire compensation: Performance, SPS MDs, pulsed system

CERN Document Server

Dorda, U

2008-01-01

A wire compensation (BBLR) scheme has been proposed in order to improve the long range beam-beam performance of the nominal LHC and its phase 1 and phase 2 upgrades[1]. In this paper we present experimental experience of the CERN SPS wires (BBLR) and report on progress with the RF BBLR.

The damper for the transverse instabilities of the SPS

CERN Document Server

Bossart, Rudolf; Gareyte, Jacques; de Raad, Bastiaan; Rossi, V

1979-01-01

For beam intensities above 10/sup 12/ protons per pulse in the SPS, collective transverse beam instabilities develop with frequencies between 15 kHz and 3 MHz because of the resistive wall effect of the vacuum chamber. An active feedback system with an electrostatic deflector has been installed in the SPS for damping the resistive wall instabilities in both the vertical and horizontal planes. Measurements have been made to determine the threshold and growth rate of these instabilities. As a novel application, the damper can be used also for the excitation of small coherent betatron oscillations. A phase-locked loop tracks the beam oscillations and provides a continuous display of the betatron wave-number Q during the cycle. (4 refs).

The SHiP experiment at CERN SPS

CERN Document Server

Di Crescenzoon, A

2016-01-01

SHiP is a new general purpose fixed target facility, whose Technical Proposal has been recently submitted to the CERN SPS Committee. In its initial phase, the 400 GeV proton beam extracted from the SPS will be dumped on a heavy target with the aim of integrating 2 × 1020 pot in 5 years. A dedicated detector located downstream of the target, based on a long vacuum tank followed by a spectrometer and particle identification detectors, will allow probing a variety of models with light long-lived exotic particles and masses below a few GeV/c2. The beam dump is also an ideal source of tau neutrinos, the less known particle in the Standard Model. Another dedicated detector, based on the Emulsion Cloud Chamber technology already used in the OPERA experiment, will allow to perform for the first time measurements of the tau neutrino deep inelastic scattering cross section. Tau neutrinos will be distinguished from tau anti-neutrinos, thus providing the first observation of the tau anti-neutrino.

Measurement and analysis of SPS kicker magnet heating and outgassing with Different Bunch Spacing

CERN Document Server

Barnes, M J; Cornelis, K; Ducimetière, L; Mahner, E; Papotti, G; Rumolo, G; Senaj, V; Shaposhnikova, E

2010-01-01

Fast kicker magnets are used to inject beam into and eject beam out of the CERN SPS accelerator ring. These kickers are generally ferrite loaded transmission line type magnets with a rectangular shaped aperture through which the beam passes. Unless special precautions are taken the impedance of the ferrite yoke can provoke significant beam induced heating, over several hours, even above the Curie temperature of the ferrite. At present the nominal bunch spacing in the SPS is 25 ns, however for an early stage of LHC operation it is preferable to have 50 ns bunch spacing. Machine Development (MD) studies have been carried out with an inter-bunch spacing of 25 ns, 50 ns or 75 ns. For some of the SPS kicker magnets the 75 ns bunch spacing resulted in considerable beam induced heating. In addition the MDs showed that 50 ns bunch spacing could result in a very rapid pressure rise in the kicker magnet and thus cause an interlock. This paper discusses the MD observations of the SPS kickers and analyses the available d...

Mechanical characterization of cemented carbide WC-6Co (%wt) manufactured by SPS (Spark Plasma Sintering; Caracterizacao mecanica de metal duro WC-6Co (%massa) sinterizado via SPS (Spark Plasma Sintering)

Energy Technology Data Exchange (ETDEWEB)

Boidi, G.; Tertuliano, A.J.; Machado, I.F., E-mail: guido.boidi@usp.br [Universidade de Sao Paulo (USP), SP (Brazil). Departamento de Engenharia Mecatronica e Sistemas Mecanicos; Rodrigues, D. [BRATS- Filtros Sinterizados e Pos Metalicos, Cajamar, SP (Brazil)

2016-07-01

This work aimed to manufacture cemented carbide (WC-6%wtCo) obtained by SPS (Spark Plasma Sintering) process and to carry out the mechanical characterization by hardness and fracture toughness. The material was consolidated at 1100 deg C for different holding times (1 min, 5 min, 10 min), in order to evaluate the densification. A reference sample was also used to be compared to SPS. Optical and scanning electron microscopy were carried out to characterize the microstructural features of the samples and mechanical properties were obtained by hardness measurements (micro and macro) and instrumented indentation. The fracture toughness was calculated with the method of Palmqvist. Best results were found in the material sintered by SPS for 10 minutes of holding time, in which 97% of relative density and about 1600 HV{sub 10} was reached. (author)

Satellite Power Systems (SPS) concept definition study (Exhibit D). Volume 5: Systems engineering/integration research and technology

Science.gov (United States)

Hanley, G. M.

1981-01-01

Guidelines and ground rules followed in the development of requirements for the SPS are presented. Development planning objectives are specified in each of these areas, and evolutionary SPS program scenarios are described for the various concepts studied during the past one year contract. Program descriptions are presented as planning packages of technical tasks, and schedule phasing. Each package identifies the ground based technology effort that will facilitate SPS definitions, designs, development, and operations.

Using Systemic Problem Solving (SPS) to Assess Student ...

African Journals Online (AJOL)

This paper focuses on the uses of systemic problem solving in chemistry at the tertiary level. Traditional problem solving (TPS) is a useful tool to help teachers examine recall of information, comprehension, and application. However, systemic problem solving (SPS) can challenge students and probe higher cognitive skills ...

Satellite Power System (SPS): an Overview of Prospective Organizational Structures in the Solar Satellite Field

Science.gov (United States)

Edler, H. G.

1978-01-01

A literature survey, interviews with acknowledged experts in the fields of organizational entities, space, solar energy, and the SPS concept, and an analysis of these inputs to identify the organizational alternatives and make judgments as to their feasibility to serve as patterns for a future SPS entity are presented. Selection and evaluation criteria were determined to include timeliness, reliability, and adequacy to contribute meaningfully to the U.S. supply; political feasibility (both national and international) and cost-effectiveness (including environmental and other external costs). Based on these criteria, four organizational alternatives are discussed which offer reasonable promise as potential options for SPS. These included three domestic alternatives and one international alternative.

SHiP: a new multipurpose beam-dump experiment at the SPS.

CERN Document Server

AUTHOR|(SzGeCERN)387671

2016-01-01

SHiP is an experiment to look for very weakly interacting particles at a new to be constructed beam-dum p facility at the CERN SPS. The SHiP Technical Proposal has been submitted to the CERN SPS Committee in April 2015. The 400 GeV/c proton beam extracted from the SPS will be dumped on a heavy target with the aim of integ rating $2\\times 10^{20}$ proton on target in five years. A detector located downstream of the target, based on a long vacuum tank followed by a spectrometer and particle identification detectors, will allow probing a variety of models with light long-lived exotic particles and masses below a few GeV/c$^2$. The main focus will be the physics of the so-called Hidden Portals, i.e. search for Dark Photons, Light scalars and pseudo-scalars, and Heavy Neutral Leptons (HNL). The sensitivity to HNL will allow for the first time to probe, in the mass range between the kaon and the charm meson mass, a coupling range for which Baryogenesis and active neutrino masses could also be explained...

Ionizing radiation risks to Satellite Power Systems (SPS) workers in space

Energy Technology Data Exchange (ETDEWEB)

1980-12-01

A reference Satellite Power System (SPS) has been designed by NASA and its contractors for the purposes of evaluating the concept and carrying out assessments of the various consequences of development, including those on the health of the space workers. The Department of Energy has responsibility for directing various assessments. Present planning calls for the SPS workers to move from Earth to a low earth orbit (LEO) at an altitude of 500 kilometers; to travel by a transfer ellipse (TE) trajectory to a geosynchronous orbit (GEO) at an altitude of 36,000 kilometers; and to remain in GEO orbit for about 90 percent of the total time aloft. The radiation risks to the health of workers who will construct and maintain solar power satellites in the space environment are studied. The charge to the committee was: (a) to evaluate the radiation environment estimated for the Reference System which could represent a hazard; (b) to assess the possible somatic and genetic radiation hazards; and (c) to estimate the risks to the health of SPS workers due to space radiation exposure, and to make recommendations based on these conclusions. Details are presented. (WHK)

Bunch rotation tests at SPS flat top for the AWAKE experiment

CERN Document Server

Argyropoulos, T; Bohl, T; Esteban Müller, J F; Petrenko, A; Shaposhnikova, E; Timko, H

2013-01-01

This note summarises the results of two MDs on bunch rotation at SPS flat top. The first MD was carried out on 11th July 2012 with the Q26 optics, while the second MD on the 30th October 2012 used the Q20 optics. To obtain a short bunch length, which is important for the plasma wake-field acceleration project AWAKE, the bunches have been rotated in longitudinal phase space on the SPS flat top. The aim of the MDs was to obtain first estimates of what bunch length, intensity, and transverse emittances - which are crucial for the project - can be achieved for high-intensity single bunches.

Multiplicity fluctuations of identified hadrons in p+p interactions at SPS energies

CERN Document Server

Maćkowiak-Pawłowska, Maja

2014-01-01

Study of energy and system size fluctuations of identified hadrons is one of the key goals of NA61/SHINE at the CERN SPS. Results may allow to discover the critical point (CP) of strongly interacting matter as well as to uncover properties of the onset of deconfinement (OD). But fluctuations exhibit numerous other sources starting from most basic ones like volume effects and conservation laws. NA49 seems to observe fluctuations related to CP in collisions of medium size nuclei at top SPS energy. However, this result will remain inconclusive until systematic data on energy and system size dependence will be available. Moreover, fluctuations in p+p as well as in Pb+Pb interactions should be better understood. In this contribution results on multiplicity fluctuations of identified hadrons in p+p interactions at the CERN SPS energies will be presented. The NA61 data will be compared with the corresponding results from central Pb+Pb collisions of NA49 in the common acceptance region of both experiments. Moreover, ...

New Spill Control for the Slow Extraction in the Multi-Cycling SPS

CERN Document Server

Kain, Verena; Effinger, Ewald

2016-01-01

The flux of particles slow extracted with the 1/3 integer resonance from the Super Proton Synchrotron at CERN was previously controlled with a servo-spill feedback system which acted on the horizontal tune such as to keep the spill rate as constant as possible during the whole extraction time. The current in two servo-quadrupoles was modulated as a function of the difference between the measured and the desired spill rate. With servo quadrupoles at a single location in the SPS ring and the SPS in multi-cycling mode, the trajectory of the slow extracted beam was seen to change from cycle to cycle depending on the current applied by the servo feedback. Hence this system was replaced by a feed-forward tune correction using the main SPS quadrupoles. In this way the spill control can now be guaranteed without changing the trajectory of the extracted beam. This paper presents the algorithm and implementation in the control system and summarizes the advantages of the new approach. The obtained spill characteristics ...

A new SPS programme

CERN Document Server

Gazdzicki, Marek; Christakoglou, P.; Diakonos, F.; Panagiotou, A.D.; Petridis, A.; Vassiliou, M.; Cafagna, F.; Catanesi, M.G.; Montaruli, T.; Radicioni, E.; Rohrich, D.; Boldizsar, L.; Fodor, Z.; Laszlo, A.; Palla, G.; Szentpetery, I.; Vesztergombi, G.; Cleymans, J.; Brzychczyk, J.; Katrynska, N.; Karabowicz, R.; Majka, Z.; Planeta, R.; Staszel, P.; Baatar, B.; Kolesnikov, V.I.; Malakhov, A.I.; Melkumov, G.L.; Sissakian, A.N.; Sorin, Alexander Savelievich; Rauch, W.; Gazdzicki, M.; Lungwitz, B.; Mitrovski, M.; Renfordt, R.; Schuster, T.; Strabel, C.; Stroebele, H.; Blondel, A.; Bravar, A.; Di Marco, M.; Blumer, J.; Engel, R.; Haungs, A.; Meurer, C.; Roth, M.; Gazdzicki, M.; Korus, R.; Mrowczynski, St.; Rybczynski, M.; Seyboth, P.; Stefanek, G.; Wlodarczyk, Z.; Wojtaszek, A.; Guber, F.; Kurepin, A.; Ivashkin, A.; Maevskaya, A.; Andrieu, B.; Dumarchez, J.; Choi, K.-U.; Kim, J.-H.; Yi, J.-G.; Yoo, I.-K.; Kolev, D.; Tsenov, R.; Asryan, A.G.; Derkach, D.A.; Feofilov, G.A.; Igolkin, S.; Ivanov, A.S.; Kolevatov, R.S.; Kondratiev, V.P.; Naumenko, P.A.; Vechernin, V.V.; Chung, P.; Lacey, R.; Taranenko, A.; Kobayashi, T.; Nakadaira, T.; Sakashita, K.; Sekiguchi, T.; Grebieszkow, K.; Kikola, D.; Peryt, W.; Pluta, J.; Slodkowski, M.; Szuba, M.; Anticic, T.; Kadija, K.; Nikolic, V.; Susa, T.

2006-01-01

A new experiemntal program to study hadron production in hadron-nucleus and nucleus-nucleus collisions at the CERN SPS has been recently proposed by the NA49-future collaboration. The physics goals of the program are: (i) search for the critical point of strongly interacting matter and a study of the properties of the onset of deconfinemnt in nucleus-nucleus collisions, (ii) measurements of correlations, fluctuations and hadron spectra at high transverse momentum in proton-nucleus collisions needed as for better understanding of nucleus-nucleus results, (iii) measurements of hadron production in hadron-nucleus interactions needed for neutrino (T2K) and cosmic-ray (Pierre Auger Observatory and KASCADE) expriments. The physics of the nucleus-nucleus program is reviewed in this presentation.

Preliminary environmental assessment for the satellite power system (SPS)

Energy Technology Data Exchange (ETDEWEB)

1978-10-01

A preliminary assessment of the impact of the Satellite Power System (SPS) on the environment is presented. Information that has appeared in documents referenced herein is integrated and assimilated. The state-of-knowledge as perceived from recently completed DOE-sponsored studies is disclosed, and prospective research and study programs that can advance the state-of-knowledge and provide an expanded data base for use in an assessment planned for 1980 are defined. Alternatives for research that may be implemented in order to achieve this advancement are also discussed in order that a plan can be selected which will be consistent with the fiscal and time constraints on the SPS Environmental Assessment Program. Health and ecological effects of microwave radiation, nonmicrowave effects on health and the environment (terrestrial operations and space operations), effects on the atmosphere, and effects on communications systems are examined in detail. (WHK)

Aerial view of the CERN-Meyrin site during building work for the SPS

CERN Multimedia

1974-01-01

Visible on the right hand site are three building areas: in front the area around pit 6 of the SPS (where the ejection to the West Area branches off), in the middle the area around the 'civil engineering pit 7', and in the back the area around the SPS pit 1 where injection takes place. The SPS tunnel, 6910 m in length with an inner diameter of 4m in its cross section, is at an elevation of 400 m above sea level corresponding to a depth below the surface which varies between 23 and 65 m. It has 6 regularly spaced access pits. The further pit 7 is situated on the injection line about 200m from the injection point. It was used to extract material excavated from the ring and to bring in the precast elements and the concrete for lining the tunnel with a shell of about 30 cm thickness.

2002 Nonlinear Optics Measurements andModelling for the SPS at 26 GeV

CERN Document Server

Arduini, Gianluigi; Faus-Golfe, A; Iida, N; Tomás, R; CERN. Geneva. AB Department

2003-01-01

During SPS MDs in the summer of 2002, nonlinear chromaticity, coupling, amplitude-dependent detuning, resonance driving terms and phase advancesalong the ring were measured with a 72-bunch LHC batch at 26 GeV. Following the procedure developed in previous years, the SPS optics model has been updated, by adjusting the magnitude of sextupole and decapole components in the SPS dipole magnets and octupole components in the quadrupoles, respectively, to values which would be consistent with the measurements. We compare the field errors deduced in 2002, measuring over a larger momentum range, with those found in 2001 and 2000. We show that the resolution can be improved by averaging over the turn-by-turn beam position data from all BPMs, distributed around the ring, instead of using the single dedicated pick up of the tune meter. Computations by two different codes, MAD and SAD, indicate the sensitivity to matching algorithm and magnet representation. Finally, the tune shifts with transverse amplitude, the driving ...

Evaluation of strip-line pick-up system for the SPS wideband transverse feedback system

CERN Document Server

Kotzian, G; Steinhagen, R J; Valuch, D; Wehrle, U

2017-01-01

The proposed SPS Wideband Transverse Feedback sys- tem requires a wide-band pick-up system to be able to de- tect intra-bunch motion within the SPS proton bunches, captured and accelerated in a 200 MHz bucket. We present the electro-magnetic design of transverse beam position pick-up options optimised for installation in the SPS and evaluate their performance reach with respect to direct time domain sampling of the intra-bunch motion. The analy- sis also discusses the achieved subsystem responses of the associated cabling with new low dispersion smooth wall coaxial cables, wide-band generation of intensity and posi- tion signals by means of 180 degree RF hybrids as well as passive techniques to electronically suppress the beam off- set signal, needed to optimise the dynamic range and posi- tion resolution of the planned digital intra-bunch feedback system.

SPS Machine Protection Incident in 2009

CERN Document Server

Wenninger, J

2009-01-01

During the 008 SPS run a single machine operation incident happened on June 27th when a high intensity CNGS beam was lost in a dipole of sextant 1 following a time system ‘freeze’. The vacuum chamber was punctured over a length of over 10 cm, and the vacuum in the affected sector rose to atmospheric pressure. The dipole was exchanged June 30th. This note describes the incident in detail and presents the measures taken to avoid a similar incident in the future.

The SPS beam parameters, the operational cycle, and proton sharing with the SHiP facility

CERN Document Server

Arduini, Gianluigi; Gatignon, Lau; Cornelis, Karel

2015-01-01

The SHiP experiment aims at acquiring a total of 4×1019 protons on target per year. Based on demonstrated SPS performance for CNGS, the expected proton sharing between the TCC2 targets and SHiP is estimated taking into account the constraints in the super-cycle composition. We review the SPS beam parameters, the operational cycles taking into account the concurrent operation of the SPS as LHC injector and for the TCC2 experiments and the limitations on the maximum possible power dissipation and the expected sharing of the protons on target of the SHiP facility with the TCC2 targets. As a typical example this aim could be achieved while maintaining a duty cycle for the other fixed target experiments of about 18%.

The GCKIII Kinase Sps1 and the 14-3-3 Isoforms, Bmh1 and Bmh2, Cooperate to Ensure Proper Sporulation in Saccharomyces cerevisiae

Science.gov (United States)

Slubowski, Christian J.; Paulissen, Scott M.; Huang, Linda S.

2014-01-01

Sporulation in the budding yeast Saccharomyces cerevisiae is a developmental program initiated in response to nutritional deprivation. Sps1, a serine/threonine kinase, is required for sporulation, but relatively little is known about the molecular mechanisms through which it regulates this process. Here we show that SPS1 encodes a bona-fide member of the GCKIII subfamily of STE20 kinases, both through phylogenetic analysis of the kinase domain and examination of its C-terminal regulatory domain. Within the regulatory domain, we find Sps1 contains an invariant ExxxPG region conserved from plant to human GCKIIIs that we call the EPG motif; we show this EPG motif is important for SPS1 function. We also find that Sps1 is phosphorylated near its N-terminus on Threonine 12, and that this phosphorylation is required for the efficient production of spores. In Sps1, Threonine 12 lies within a 14-3-3 consensus binding sequence, and we show that the S. cerevisiae 14-3-3 proteins Bmh1 and Bmh2 bind Sps1 in a Threonine 12-dependent fashion. This interaction is significant, as BMH1 and BMH2 are required during sporulation and genetically interact with SPS1 in sporulating cells. Finally, we observe that Sps1, Bmh1 and Bmh2 are present in both the nucleus and cytoplasm during sporulation. We identify a nuclear localization sequence in Sps1 at amino acids 411–415, and show that this sequence is necessary and sufficient for nuclear localization. Taken together, these data identify regions within Sps1 critical for its function and indicate that SPS1 and 14-3-3s act together to promote proper sporulation in S. cerevisiae. PMID:25409301

Successful test of SPS-to-LHC beamline

CERN Multimedia

Maximilien Brice

2004-01-01

On 23 October there was great excitement in the Prevessin control room when, on the first attempt, a beam passed over 2.5 km down the new SPS-to-LHC transfer line, TI8, to within a few metres of the LHC tunnel. Members of the AB, AT and TS departments involved in the beamline and its test, celebrate their success with the Director General, Robert Aymar, and the LHC Project Leader, Lyn Evans.

Successful test of SPS-to-LHC beamline

CERN Multimedia

2004-01-01

On 23 October there was great excitement in the Prevessin control room when, on the first attempt, a beam passed over 2.5 km down the new SPS-to-LHC transfer line, TI8, to within a few metres of the LHC tunnel. Above: members of the AB, AT and TS departments involved in the beamline and its test, celebrate their success with the Director General, Robert Aymar, and the LHC Project Leader, Lyn Evans.

Arrival of the Robbins machine in LSS1 after completing the boring of the SPS tunnel.

CERN Multimedia

CERN PhotoLab

1974-01-01

A few months after the signature of the agreement giving the go-ahead for the expansion of CERN into French territory (see Bulletin no.24/2004), work began on the Super Proton Synchrotron (SPS). Two years later, on 31 July 1974, the Robbins tunnel-boring machine excavating the SPS tunnel returned to its starting point (see photograph). It had excavated a tunnel with a circumference of 7 kilometres, at an average depth of 40 metres below the surface. The tunnel straddled the Franco-Swiss border, making the SPS the first cross-border accelerator. More than a thousand magnets were needed to equip the ring. The civil engineering and installation work was completed in record time after only four years. The SPS was equipped with a control system which was ahead of its time, consisting of 24 small control computers distributed in the tunnel and the control room and communicating by means of a high-rate data transmission system. The main control room housed only four consoles as opposed to the banks of electronic eq...

Successful beam test of the SPS-to-LHC transfer line TI2

CERN Multimedia

2007-01-01

Image of the first beam spot on the last BTV screen traversed by the beam during the TI 2 test.At 12:03:47 on 28 October a beam passed down the 2.7 km of the new SPS-to-LHC transfer line TI 2 at the first attempt, to within some 50 m of the LHC tunnel. After initial tuning, a range of measurements was carried out with a low intensity proton beam and preliminary analyses look good. After the test, no increase in radiation levels was found in either the LHC or ALICE, and the zones were rapidly opened again for access. As from next year TI 2 will regularly transport a beam from the SPS to the LHC injection point of Ring 1, near Point 2 (ALICE). The TI 8 transfer line, which will bring particles from the SPS to the injection point in Ring 2, near Point 8 (LHCb), was commissioned successfully with low intensity beam in 2004. The two LHC injection lines have a combined length of 5.6 km and comprise some seven hundred warm magnets. While a...

NA61/SHINE low energy program at SPS

CERN Document Server

Abgrall, N.; Andrieu, B.; Anticic, T.; Antoniou, N.; Argyriades, J.; Asryan, A.G.; Baatar, B.; Blondel, A.; Blumer, J.; Boldizsar, L.; Bravar, A.; Brzychczyk, J.; Bubak, A.; Bunyatov, S.A.; Choi, K.-U.; Christakoglou, P.; Chung, P.; Cleymans, J.; Derkach, D.A.; Diakonos, F.; Dominik, W.; Dumarchez, J.; Engel, R.; Ereditato, A.; Feofilov, G.A.; Fodor, Z.; Ferrero, A.; Gazdzicki, M.; Golubeva, M.; Grebieszkow, K.; Grzeszczuk, A.; Guber, F.; Hasegawa, T.; Haungs, A.; Igolkin, S.; Ivanov, A.S.; Ivashkin, A.; Kadija, K.; Katrynska, N.; Kielczewska, D.; Kikola, D.; Kisiel, J.; Kobayashi, T.; Kolesnikov, V.I.; Kolev, D.; Kolevatov, R.S.; Kondratiev, V.P.; Kowalski, S.; Kurepin, A.; Lacey, R.; Laszlo, A.; Lyubushkin, V.V.; Majka, Z.; Malakhov, A.I.; Marchionni, A.; Marcinek, A.; Maris, I.; Matveev, V.; Melkumov, G.L.; Meregaglia, A.; Messina, M.; Mijakowski, P.; Mitrovski, M.; Montaruli, T.; Mrowczynski, St.; Murphy, S.; Nakadaira, T.; Naumenko, P.A.; Nikolic, V.; Nishikawa, K.; Palczewski, T.; Palla, G.; Panagiotou, A.D.; Peryt, W.; Planeta, R.; Pluta, J.; Popov, B.A.; Posiadala, M.; Przewlocki, P.; Rauch, W.; Ravonel, M.; Renfordt, R.; Rohrich, D.; Rondio, E.; Rossi, B.; Roth, M.; Rubbia, A.; Rybczynski, M.; Sadovsky, A.; Sakashita, K.; Schuster, T.; Sekiguchi, T.; Seyboth, P.; Shibata, M.; Sissakian, A.N.; Skrzypczak, E.; Slodkowski, M.; Sorin, A.S.; Staszel, P.; Stefanek, G.; Stepaniak, J.; Strabel, C.; Stroebele, H.; Susa, T.; Szentpetery, I.; Szuba, M.; Tada, M.; Taranenko, A.; Tsenov, R.; Ulrich, R.; Unger, M.; Vassiliou, M.; Vechernin, V.V.; Vesztergombi, G.; Wlodarczyk, Z.; Wojtaszek, A.; Zipper, W.

2009-01-01

Status of the new experimental program to study hadron production in hadron-nucleus and nucleus-nucleus collisions at the CERN SPS will be presented. A physics motivation will be given for the part of the program related to the physics of strongly interacting matter. Upgrades of the NA61 experimental set-up and data taking plans will be described in detail.

Vancomycin-resistant Enterococcus faecium bacteraemia as a complication of Kayexalate (sodium polystyrene sulfonate, SPS) in sorbitol-induced ischaemic colitis.

Science.gov (United States)

Cerrud-Rodriguez, Roberto Christian; Alcaraz-Alvarez, Diego; Chiong, Brian Bobby; Ahmed, Abdurhman

2017-11-09

We present the case report of an 80-year-old woman with chronic kidney disease stage G5 admitted to the hospital with fluid overload and hyperkalaemia. Sodium polystyrene sulfonate (SPS, Kayexalate) in sorbitol suspension was given orally to treat her hyperkalaemia, which precipitated an episode of SPS in sorbitol-induced ischaemic colitis with the subsequent complication of vancomycin-resistant Enterococcus (VRE) bacteraemia. SPS (Kayexalate) in sorbitol suspension has been implicated in the development of intestinal necrosis. Sorbitol, which is added as a cathartic agent to decrease the chance of faecal impaction, may be primarily responsible through several proposed mechanisms. The gold standard of diagnosis is the presence of SPS crystals in the colon biopsy. On a MEDLINE search, no previous reports of a VRE bacteraemia as a complication of biopsy-confirmed SPS in sorbitol ischaemic colitis were found. To the best of our knowledge, ours would be the first such case ever reported. © BMJ Publishing Group Ltd (unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Heavy Ion Physics at the CERN SPS: Roots 1974-1984 and Key Results

CERN Multimedia

CERN. Geneva

2014-01-01

Two communities, Nuclear and Particle Physics, had to come together to open up a new field at the CERN SPS in the early eighties, bringing CERN to the forefront worldwide until the start of RHIC in 2000. I will discuss the period before that, including the basic new ideas on parton deconfinement, key workshops, alternative accelerator options in the LBL-GSI-CERN triangle, and the final convergence of the three labs on the SPS, sacrificing any home future in this field for the first two. In 1984, 5 major experiments were approved for initially O16 and S32 beams at the SPS, with an unprecedented reuse of existing experimental equipment. Subsequent evolution followed thanks to intense learning processes, leading to a second generation of much improved or completely new experiments together with Pb beams starting in 1994. I will summarise the key results and their (then still cautious) interpretation as of 2000. They were used as an input to a Press Conference at CERN, announcing the detection of a 'n...

SPS ionosphere/microwave beam interactions: Arecibo experimental studies

International Nuclear Information System (INIS)

Duncan, L.M.

1980-10-01

The purpose of this program is to determine the environmental impacts associated with the operation of the proposed SPS microwave power transmission system. It is expected that thermal effects will provide the dominant force driving the nonlinear ionosphere/microwave beam interactions. Collisional damping of radio waves, producing ohmic heating of the ionospheric plasma, depends inversely on the square of the radio wave frequency. Therefore, equivalent heating and equivalent thermal forces can be generated at lower radiated power densities by using lower radio wave frequencies. This principle is fundamental to a large part of the experimental program. An understanding of the physics of the specific interactions excited by the SPS microwave beam is also an important part of the assessment program. This program is designed to determine instability thresholds, the growth rates and spatial extent of the resultant ionospheric disturbances, and the frequency and power dependences of the interactions. How these interactions are affected by variations in the natural ionospheric conditions, how different instabilities occurring simultaneously may affect each other, and how distinct microwave beams might mutually interact are studied. Status of the program is described

Mechanical characterization of cemented carbide WC-6Co (%wt) manufactured by SPS (Spark Plasma Sintering

International Nuclear Information System (INIS)

Boidi, G.; Tertuliano, A.J.; Machado, I.F.

2016-01-01

This work aimed to manufacture cemented carbide (WC-6%wtCo) obtained by SPS (Spark Plasma Sintering) process and to carry out the mechanical characterization by hardness and fracture toughness. The material was consolidated at 1100 deg C for different holding times (1 min, 5 min, 10 min), in order to evaluate the densification. A reference sample was also used to be compared to SPS. Optical and scanning electron microscopy were carried out to characterize the microstructural features of the samples and mechanical properties were obtained by hardness measurements (micro and macro) and instrumented indentation. The fracture toughness was calculated with the method of Palmqvist. Best results were found in the material sintered by SPS for 10 minutes of holding time, in which 97% of relative density and about 1600 HV_1_0 was reached. (author)

Shallow gas incident in 3-ELPS-15D-SPS well; Incidente com shallow gas no poco 3-ELPS-15D-SPS

Energy Technology Data Exchange (ETDEWEB)

Ribeiro, Rubens Fausto [Agencia Nacional do Petroleo, Gas Natural e Biocombustiveis (ANP), Rio de Janeiro, RJ (Brazil)

2004-07-01

One of the concerns during the planning phase of an exploratory offshore well drilling is the possibility of occurrence of a shallow gas accumulation. In spite of being a rare event, taking into account that an event like this can have disastrous consequences, the cares to work with that type of incident cannot be despised. As example, in 2003, during the operations in the extension well 3-ELPS-15D-SPS, it happened the uncontrolled influx of water and gas to the bottom of the sea: the annular space between the 30'' and 13 3/8'' casings was not filled out with cement, allowing the flow from a shallow permeable interval to the bottom of the sea through the wellhead's cement return orifices, generating the need of an corrective action to make the abandonment of the well in accordance with the Regulation of Abandonment of Wells existent in Brazil. This work presents the mechanical conditions of the interval close to the wet wellhead of the 3-ELPS-15D-SPS, enumerating the sequence of operations accomplished to solve the problem. (author)

High density matter in AGS, SPS and RHIC collisions. Proceedings. Volume 9

International Nuclear Information System (INIS)

1998-01-01

This 1-day workshop focused on phenomenological models regarding the specific question of the maximum energy density achievable in collisions at AGS, SPS and RHIC. The idea was to have 30-minute (or less) presentations of each model--but not the model as a whole, rather then that strongly narrowed to the above physics question. The key topics addressed were: (1) to estimate the energy density in heavy-ion collisions within a model, and to discuss its physical implications; (2) to suggest experimental observables that may confirm the correctness of a model approach--with respect to the energy density estimate; (3) to compare with existing data from AGS and SPS heavy-ion collisions, and to give predictions for the future RHIC experiments. G. Ogilvie started up the workshop with a critical summary of experimental manifestations of high-density matter at the AGS, and gave a personal outlook on RHIC physics. R. Mattiello talked about his newly developed hadron cascade model for applications to AGS and SPS collisions. Next, D. Kharzeev gave a nice introduction of the Glauber approach to high-energy collisions and illustrated the predictive power of this approach in nucleus-nucleus collisions at the SPS. It followed S. Vance with a presentation of the baryon-junction model to explain the observed baryon stopping phenomenon in collisions of heavy nuclei. S. Bass continued with a broad perspective of the UrQMD model, and provided insight into the details of the microscopic dynamical features of nuclear collisions at high energy. J. Sandweiss and J. Kapusta addressed the interesting aspect of photon production in peripherical nuclear collisions due to intense electromagnetic bremstrahlung by the highly charged, fast moving ions. Finally, H. Sorge closed up the one-day workshop with a presentation of his recent work with the RQMD model. This report consists of a summary and vugraphs of the presentations

High density matter in AGS, SPS and RHIC collisions: Proceedings. Volume 9

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-12-01

This 1-day workshop focused on phenomenological models regarding the specific question of the maximum energy density achievable in collisions at AGS, SPS and RHIC. The idea was to have 30-minute (or less) presentations of each model--but not the model as a whole, rather then that strongly narrowed to the above physics question. The key topics addressed were: (1) to estimate the energy density in heavy-ion collisions within a model, and to discuss its physical implications; (2) to suggest experimental observables that may confirm the correctness of a model approach--with respect to the energy density estimate; (3) to compare with existing data from AGS and SPS heavy-ion collisions, and to give predictions for the future RHIC experiments. G. Ogilvie started up the workshop with a critical summary of experimental manifestations of high-density matter at the AGS, and gave a personal outlook on RHIC physics. R. Mattiello talked about his newly developed hadron cascade model for applications to AGS and SPS collisions. Next, D. Kharzeev gave a nice introduction of the Glauber approach to high-energy collisions and illustrated the predictive power of this approach in nucleus-nucleus collisions at the SPS. It followed S. Vance with a presentation of the baryon-junction model to explain the observed baryon stopping phenomenon in collisions of heavy nuclei. S. Bass continued with a broad perspective of the UrQMD model, and provided insight into the details of the microscopic dynamical features of nuclear collisions at high energy. J. Sandweiss and J. Kapusta addressed the interesting aspect of photon production in peripherical nuclear collisions due to intense electromagnetic bremstrahlung by the highly charged, fast moving ions. Finally, H. Sorge closed up the one-day workshop with a presentation of his recent work with the RQMD model. This report consists of a summary and vugraphs of the presentations.

Incident energy dependence of collision dynamics in A+A reactions from AGS to SPS

International Nuclear Information System (INIS)

Nara, Yasushi

2000-01-01

Based on the hadronic transport model of JAM, I calculate the time evolution of particles, density, temperature and energy density for the heavy ion collision at the incident energies of AGS(11A GeV), JHF(25A GeV) and SPS(158A GeV). Microscopic calculations show that resonance matter with extremely large baryon density is created at AGS energy, while at JHF energy, quark matter with extremely large baryon density is suggested. At SPS energy, quark matter with large baryon density might be created. (author)

Removing Known SPS Intensity Limitations for High Luminosity LHC Goals

CERN Document Server

Shaposhnikova, Elena; Bohl, Thomas; Cruikshank, Paul; Goddard, Brennan; Kaltenbacher, Thomas; Lasheen, Alexandre; Perez Espinos, Jaime; Repond, Joël; Salvant, Benoit; Vollinger, Christine

2016-01-01

In preparation of the SPS as an LHC injector its impedance was significantly reduced in 1999 - 2000. A new SPS impedance reduction campaign is planned now for the High Luminosity (HL)-LHC project, which requires bunch intensities twice as high as the nominal one. One of the known intensity limitations is a longitudinal multi-bunch instability with a threshold 3 times below this operational intensity. The instability is presently cured using the 4th harmonic RF system and controlled emittance blow-up, but reaching the HL-LHC parameters cannot be assured without improving the machine impedance. Recently the impedance sources responsible for this instability were identified and implementation of their shielding and damping is foreseen during the next long shutdown (2019 - 2020) in synergy with two other important upgrades: amorphous carbon coating of (part of) the vacuum chamber against the e-cloud effect and rearrangement of the 200 MHz RF system. In this paper the strategy of impedance reduction is presented t...

What have we learned and want to learn from heavy ion collisions at CERN SPS?

International Nuclear Information System (INIS)

Shuryak, E.V.

1999-01-01

The talk is a mini-review of current status of the field, with emphasis on SPS heavy ion program, now and beyond 2000 (as asked by the organizers). The main question is, of course, whether we can convince ourselves and community at large that the QGP is in fact produced at SPS. We came a long way toward the positive answer, and are definitely on strongly rising part of the learning curve. Still, in few key directions we lack important pieces of evidences

Beam Scraping in the SPS for LHC Injection Efficiency and Robustness Studies

CERN Document Server

Letnes, Paul/LPA; Myrheim, Jan

2008-01-01

The Large Hadron Collider (LHC) at CERN will be the world's most powerful accelerator when it is commissioned in fall 2008. Operation of the LHC will require injection of very high intensity beams. Fast transverse beam scrapers have been installed in the Super Proton Synchrotron (SPS) injector to detect and, if necessary, remove transverse beam tails. This will help to both diagnose and prevent beam quenches in the LHC. Scraping of a high intensity beam at top energy can potentially damage the scraper jaws. This has been studied with Monte Carlo simulations to find energy deposition and limits for hardware damage. Loss maps from scraping have been generated both with machine studies and tracking simulations. Time dependent Beam Loss Monitor (BLM) measurements have shown several interesting details about the beam. An analytical model of time dependent losses is compared with beam measurements and demonstrates that beam scraping can be used to estimate the beam size. Energy deposition simulations also give the ...

Na61/Shine at the CERN SPS

CERN Document Server

Laszlo, Andras; Aduszkiewicz, A; Andrieu, B; Anticic, T; Antoniou, N; Asryan, A G; Baatar, B; Blondel, A; Blumer, J; Boldizsar, L; Bravar, A; Brzychczyk, J; Bunyatov, S A; Cafagna, F; Catanesi, M G; Choi, K U; Christakoglou, P; Chung, P; Cleymans, J; Derkach, D A; Diakonos, F; Dominik, Wojciech; Dumarchez, J; Engel, R; Ereditato, A; Feofilov, G A; Fodor, Z; Gazdzicki, M; Golubeva, M; Grebieszkow, K; Guber, F; Haungs, A; Hess, M; Igolkin, S; Ivanov, A S; Ivashkin, A; Kadija, K; Karabowicz, R; Katrynska, N; Kielczewska, D; Kikola, D; Kim, J H; Kobayashi, T; Kolesnikov, V I; Kolev, D; Kolevatov, R S; Kondratiev, V P; Kurepin, A; Lacey, R; Lehmann, S; Lungwitz, B; Lyubushkin, V V; Maevskaya, A; Majka, Z; Malakhov, A I; Marchionni, A; Di Marco, M; Matveev, V; Melkumov, G L; Meregaglia, A; Messina, M; Meurer, C; Mijakowski, P; Mitrovski, M; Montaruli, T; Mrówczynski, S; Murphy, S; Nakadaira, T; Naumenko, P A; Nikolic, V; Palczewski, T; Pálla, G; Panagiotou, A D; Peryt, W; Petridis, A; Planeta, R; Pluta, J; Popov, B A; Posiadala, M; Przewlocki, P; Radicioni, E; Rauch, W; Renfordt, R; Röhrich, D; Rondio, E; Rossi, B; Roth, M; Rubbia, André; Rybczynski, M; Sadovskii, A; Sakashita, K; Schuster, T; Sekiguchi, T; Seyboth, P; Shileev, K; Sissakian, A N; Skrzypczak, E; Slodkowski, M; Sorin, A S; Staszel, P; Stefanek, G; Stepaniak, J; Strabel, C; Ströbele, H; Susa, T; Szentpétery, I; Szuba, M; Taranenko, A; Tsenov, R; Unger, M; Vassiliou, M; Vechernin, V V; Vesztergombi, G; Wlodarczyk, Z; Wojtaszek, A; Yi, J G; Yoo, I K

2007-01-01

Status of the new experimental program to study hadron production in hadron-nucleus and nucleus-nucleus collisions at the CERN SPS will be presented. In particular, a detailed physics motivation and experimental strategy will be given for the part of the program related to the physics of strongly interacting matter: search for the critical point of strongly interacting matter, study properties of the onset of deconfinement, and high p_T measurements in p+p and p+A interactions. The planned measurements for the neutrino T2K and cosmic-ray experiments will also be discussed.

A Student Assessment Tool for Standardized Patient Simulations (SAT-SPS): Psychometric analysis.

Science.gov (United States)

Castro-Yuste, Cristina; García-Cabanillas, María José; Rodríguez-Cornejo, María Jesús; Carnicer-Fuentes, Concepción; Paloma-Castro, Olga; Moreno-Corral, Luis Javier

2018-05-01

The evaluation of the level of clinical competence acquired by the student is a complex process that must meet various requirements to ensure its quality. The psychometric analysis of the data collected by the assessment tools used is a fundamental aspect to guarantee the student's competence level. To conduct a psychometric analysis of an instrument which assesses clinical competence in nursing students at simulation stations with standardized patients in OSCE-format tests. The construct of clinical competence was operationalized as a set of observable and measurable behaviors, measured by the newly-created Student Assessment Tool for Standardized Patient Simulations (SAT-SPS), which was comprised of 27 items. The categories assigned to the items were 'incorrect or not performed' (0), 'acceptable' (1), and 'correct' (2). 499 nursing students. Data were collected by two independent observers during the assessment of the students' performance at a four-station OSCE with standardized patients. Descriptive statistics were used to summarize the variables. The difficulty levels and floor and ceiling effects were determined for each item. Reliability was analyzed using internal consistency and inter-observer reliability. The validity analysis was performed considering face validity, content and construct validity (through exploratory factor analysis), and criterion validity. Internal reliability and inter-observer reliability were higher than 0.80. The construct validity analysis suggested a three-factor model accounting for 37.1% of the variance. These three factors were named 'Nursing process', 'Communication skills', and 'Safe practice'. A significant correlation was found between the scores obtained and the students' grades in general, as well as with the grades obtained in subjects with clinical content. The assessment tool has proven to be sufficiently reliable and valid for the assessment of the clinical competence of nursing students using standardized patients

SPS transfer line TT60 towards W-Area

CERN Multimedia

CERN PhotoLab

1978-01-01

Tranfer line TT60 from SPS LSS6 towards the W-Area. View in the direction of the beam. After the magnet, there is a secondary-emission profile monitor, followed by a secondary-emission split-foil (for centering the beam). A TV camera (sticking up prominently) looks at a scintillator screen. The huge tank (with a person standing behind it) houses a beam dump (allowing setting- up of extraction without sending a beam to the W-Area).

Charmonia suppression in nucleus-nucleus interactions at CERN SPS

CERN Document Server

Arnaldi, R; Alexa, C; Arnaldi, R; Atayan, M; Baglin, C; Baldit, A; Bedjidian, M; Beolè, S; Boldea, V; Bordalo, P; Borenstein, S R; Borges, G; Bussière, A; Capelli, L; Castanier, C; Castor, J I; Chaurand, B; Cheynis, B; Chiavassa, E; Cicalò, C; Claudino, T; Comets, M P; Constantinescu, S; Cortese, P; Cruz, J; De Falco, A; De Marco, N; Dellacasa, G; Devaux, A; Dita, S; Drapier, O; Espagnon, B; Fargeix, J; Force, P; Gallio, M; Gavrilov, Yu K; Gerschel, C; Giubellino, P; Golubeva, M B; Gonin, M; Grigorian, A A; Grigorian, S; Grossiord, J Y; Guber, F F; Guichard, A; Gulkanian, H R; Hakobyan, R S; Haroutunian, R; Idzik, M; Jouan, D; Karavitcheva, T L; Kluberg, L; Kurepin, A B; Le Bornec, Y; Lourenço, C; Macciotta, P; MacCormack, M; Marzari-Chiesa, A; Masera, M; Masoni, A; Monteno, M; Musso, A; Petiau, P; Piccotti, A; Pizzi, J R; Prado da Silva, W L; Prino, F; Puddu, G; Quintans, C; Ramello, L; Ramos, S; Rato-Mendes, P; Riccati, L; Romana, A; Scalas, E; Saturnini, P; Scomparin, E; Serci, S; Shahoyan, R; Sigaudo, F; Sitta, M; Sonderegger, P; Tarrago, X; Topilskaya, N S; Usai, G L; Vercellin, E; Villatte, L; Willis, N; Wu, T

2004-01-01

The NA50 experiment at CERN SPS has studied charmonium production in Pb-Pb collisions at 158 GeV/c per nucleon. According to the theoretical predictions the observation of the suppression of the J/ psi production yield is expected to be an unambiguous probe for a phase transition from ordinary nuclear matter towards a state in which quarks and gluons are deconfined. (10 refs).

Hadroproduction of charmonium Χ states at the SPS

International Nuclear Information System (INIS)

Lemoigne, Y.

1988-06-01

The observation of hadroproduced charmonium Χ states requires a good resolution to disentangle states of similar masses (45 MeV of difference for masses larger than 3500 MeV). The WA11 experiment was able to distinguish the two Χ(3510) and Χ(3555) states, measure their cross-section in π-beryllium at 185 GeV/c and give a ratio of contribution of this to J/Ψ production (17.7 % and 12.8 % respectively). A refined analysis of Χ-states events has shown different processes in the π-production of these states. At 185 GeV/c, the Χ(3555) comes mainly from gluon-gluon fusion, but the Χ(3510) is equally produced by quark-antiquark fusion and gluon-gluon fusion. One finds that different graphs can be envisaged, both in colour conservation as well as in colour evaporation, to contribute to charmonium state production given by simple counting rules. Using our data at 185 GeV/c and the usual structure function (like the DUKE-OWEN's ones), we are able to compute the J/Ψ, Χ 1 , and Χ 2 π-production at any other SPS energy. This calculation gives values in agreement with results from the Ω group (for J/Ψ) and the ''GAMS'' group (for Χ), at 40 GeV/c [fr

Proposal to Search for Heavy Neutral Leptons at the SPS

CERN Document Server

Bonivento, W.; Dijkstra, H.; Egede, U.; Ferro-Luzzi, M.; Goddard, B.; Golutvin, A.; Gorbunov, D.; Jacobsson, R.; Panman, J.; Patel, M.; Ruchayskiy, O.; Ruf, T.; Serra, N.; Shaposhnikov, M.; Treille, D.; CERN. Geneva. SPS and PS Experiments Committee; SPSC

2013-01-01

A new fixed-target experiment at the CERN SPS accelerator is proposed that will use decays of charm mesons to search for Heavy Neutral Leptons (HNLs), which are right-handed partners of the Standard Model neutrinos. The existence of such particles is strongly motivated by theory, as they can simultaneously explain the baryon asymmetry of the Universe, account for the pattern of neutrino masses and oscillations and provide a Dark Matter candidate. Cosmological constraints on the properties of HNLs now indicate that the majority of the interesting parameter space for such particles was beyond the reach of the previous searches at the PS191, BEBC, CHARM, CCFR and NuTeV experiments. For HNLs with mass below 2 GeV, the proposed experiment will improve on the sensitivity of previous searches by four orders of magnitude and will cover a major fraction of the parameter space favoured by theoretical models. The experiment requires a 400 GeV proton beam from the SPS with a total of 2x10^20 protons on target, achie...

LS1 Report: A highly choreographed ballet in the SPS

CERN Multimedia

Katarina Anthony

2014-01-01

With only one short month left until beam, the SPS teams have been kept busy with powering and operations tests. Alongside this demanding work, they have also successfully removed and replaced four key elements of the accelerator.   Since beginning their hardware-testing phase in early July, teams have been carrying out Electrical Power Converter tests and a wide range of start-up tests for the various equipment groups. Slotted amongst this busy schedule of tests were the final checks of the accelerator's magnets and beam dump. "There are three main types of magnet faults and we found we had one of each: an electrical fault (short circuit) in the magnet, a water leak (as the magnets are water cooled) and a vacuum chamber leak," says David McFarlane, the SPS technical coordinator from the Engineering Department. "On top of that, there was a problem with the main beam dump, which meant it also had to be replaced. In the end, rather than stopping the tests for each...

Measurements made in the SPS with a rest gas profile monitor by collecting electrons

International Nuclear Information System (INIS)

Fischer, C.; Koopman, J.

2000-01-01

Measurements have regularly been performed during the 1999 run, using the Rest Gas Monitor installed in the SPS. The exploited signal resulted from electrons produced by ionization of the rest gas during the circulating beam passage. A magnetic field parallel to the electric extraction field was applied to channel the electrons. Proton beam horizontal transverse distributions were recorded during entire SPS acceleration cycles, between 14 GeV/c and 450 GeV/c and for different beam structures and bunch intensities. The influence of several parameters on the measured beam profiles was investigated. Results are presented and analyzed in order to determine the performance that can be expected

Study of Hadron Production in Hadron-Nucleus and Nucleus-Nucleus Collisions at the CERN SPS

CERN Multimedia

Klochkov, V; Herve, A E; Kowalski, S; Kaptur, E A; Kowalik, K L; Dominik, W M; Matulewicz, T N; Krasnoperov, A; Feofilov, G; Vinogradov, L; Kovalenko, V; Johnson, S R; Planeta, R J; Rubbia, A; Marton, K; Messerly, B A; Puzovic, J; Bogomilov, M V; Bravar, A; Renfordt, R A E; Deveaux, M; Engel, R R; Grzeszczuk, A; Davis, N; Kuich, M; Lyubushkin, V; Kondratev, V; Kadija, K; Diakonos, F; Slodkowski, M A; Rauch, W H; Pistillo, C; Laszlo, A; Nakadaira, T; Hasegawa, T; Sadovskiy, A; Morozov, S; Petukhov, O; Mathes, H; Roehrich, D; Marcinek, A J; Marino, A D; Grebieszkow, K; Di luise, S; Wlodarczyk, Z; Rybczynski, M A; Wojtaszek-szwarc, A; Nirkko, M C; Sakashita, K; Golubeva, M; Kurepin, A; Manic, D; Kolev, D I; Kisiel, J E; Koziel, M E; Rondio, E; Larsen, D T; Czopowicz, T R; Seyboth, P; Turko, L; Guber, F; Marin, V; Busygina, O; Strikhanov, M; Taranenko, A; Cirkovic, M; Roth, M A; Pulawski, S M; Aduszkiewicz, A M; Bunyatov, S; Vechernin, V; Nagai, Y; Anticic, T; Dynowski, K M; Mackowiak-pawlowska, M K; Stefanek, G; Pavin, M; Fodor, Z P; Nishikawa, K; Tada, M; Blondel, A P P; Stroebele, H W; Posiadala, M Z; Kolesnikov, V; Andronov, E; Zimmerman, E D; Antoniou, N; Majka, Z; Dumarchez, J; Naskret, M; Ivashkin, A; Tsenov, R V; Koziel, M G; Schmidt, K J; Melkumov, G; Popov, B; Panagiotou, A; Richter-was, E M; Morgala, S J; Paolone, V; Damyanova, A; Gazdzicki, M; Unger, M T; Wilczek, A G; Stepaniak, J M; Seryakov, A; Susa, T; Staszel, P P; Brzychczyk, J; Maksiak, B; Tefelski, D B

2007-01-01

The NA61/SHINE (SHINE = SPS Heavy Ion and Neutrino Experiment) experiment is a large acceptance hadron spectrometer at the CERN SPS for the study of the hadronic final states produced in interactions of various beam particles (pions, protons, C, S and In) with a variety of fixed targets at the SPS energies. The main components of the current detector were constructed and used by the NA49 experiment. The physics program of NA61/SHINE consists of three main subjects. In the first stage of data taking (2007-2009) measurements of hadron production in hadron-nucleus interactions needed for neutrino (T2K) and cosmic-ray (Pierre Auger and KASCADE) experiments will be performed. In the second stage (2009-2011) hadron production in proton-proton and proton-nucleus interactions needed as reference data for a better understanding of nucleus-nucleus reactions will be studied. In the third stage (2009-2013) energy dependence of hadron production properties will be measured in nucleus-nucleus collisions as well as in p+p a...

The hardware implementation of the CERN SPS ultrafast feedback processor demonstrator

CERN Document Server

Dusakto, J E; Fox, J D; Olsen, J; Rivetta, C H; Höfle, W

2013-01-01

An ultrafast 4GSa/s transverse feedback processor has been developed for proof-of-concept studies of feedback control of e-cloud driven and transverse mode coupled intra-bunch instabilities in the CERN SPS. This system consists of a high-speed ADC on the front end and equally fast DAC on the back end. All control and signal processing is implemented in FPGA logic. This system is capable of taking up to 16 sample slices across a single SPS bunch and processing each slice individually within a reconfigurable signal processor. This demonstrator system is a rapidly developed prototype, consisting of both commercial and custom-design components. It can stabilize the motion of a single particle bunch using closed loop feedback. The system can also run open loop as a high-speed arbitrary waveform generator and contains diagnostic features including a special ADC snapshot capture memory. This paper describes the overall system, the feedback processor and focuses on the hardware architecture, design ...

Report from the NA61/SHINE experiment at the CERN SPS

CERN Document Server

Abgrall, N; Andrieu, B; Anticic, T; Antoniou, N; Asryan, A; Baatar, B; Blondel, A; Blumer, J; Boldizsar, L; Bravar, A; Brzychczyk, J; Bunyatov, S; Choi, K-U; Christakoglou, P; Chung, P; Cleymans, J; Derkach, D; Diakonos, F; Dominik, Wojciech; Dumarchez, J; Engel, R; Ereditato, A; Feofilov, G; Fodor, Z; Gazdzicki, M; Golubeva, M; Grebieszkow, K; Guber, F; Hasegawa, T; Haungs, A; Hess, M; Igolkin, S; Ivanov, A; Ivashkin, A; Kadija, K; Katrynska, N; Kielczewska, D; Kikola, D; Kim, J-H; Kobayashi, T; Kolesnikov, V; Kolev, D; Kolevatov, R; Kondratiev, V; Kurepin, A; Lacey, R; Laszlo, A; Lehmann, S; Lungwitz, B; Lyubushkin, V; Maevskaya, A; Majka, Z; Malakhov, A; Marchionni, A; Marcinek, A; Di Marco, M; Matveev, V; Melkumov, G; Meregaglia, A; Messina, M; Meurer, C; Mijakowski, P; Mitrovski, M; Mrówczynski, S; Murphy, S; Nakadaira, T; Naumenko, P; Nikolic, V; Nishikawa, K; Palczewski, T; Pálla, G; Panagiotou, A; Peryt, W; Petridis, A; Planeta, R; Pluta, J; Popov, B; Posiadala, M; Przewlocki, P; Rauch, W; Ravonel, M; Renfordt, R; Röhrich, D; Rondio, E; Rossi, B; Roth, M; Rubbia, André; Rybczynski, M; Sadovskii, A; Sakashita, K; Schuster, T; Sekiguchi, T; Seyboth, P; Shileev, K; Sisakian, A; Skrzypczak, E; Slodkowski, M; Sorin, A; Staszel, P; Stefanek, G; Stepaniak, J; Strabel, C; Ströbele, H; Susa, T; Szentpétery, I; Szuba, M; Taranenko, A; Tsenov, R; Unger, M; Vassiliou, M; Vechernin, V; Vesztergombi, G; Wlodarczyk, Z; Wojtaszek, A; Yi, J-G; Yoo, I-K

2008-01-01

The physics program of the NA61/SHINE (SHINE = SPS Heavy Ion and Neutrino Experiment) experiment at the CERN SPS consists of three subjects. In the first stage of data taking (2007-2008) the measurements of hadron production in hadron-nucleus interactions needed for neutrino (T2K) and cosmic-ray (Pierre Auger and KASCADE) experiments will be performed. In the second stage (2008-2010) hadron production in proton-proton and proton-nucleus interactions needed as a reference data for better understanding of nucleus-nucleus reactions will be studied. In the third stage (2010-2012) hadron production will be measured in nucleus-nucleus collisions, with the aim to identify the properties of the onset of deconfinement and find evidence for the critical point of strongly interacting matter. The experiment was approved at CERN in June 2007. The first pilot run was performed during October 2007. We report here first results from this run.

Prototyping Real-Time Control in the SPS

CERN Document Server

Andersson, J; Jensen, L; Jones, R; Lamont, M; Wenninger, J; Wijnands, Thijs; CERN. Geneva. AB Department

2003-01-01

Real-time control of beam related parameters will be required in the LHC. In order to gain experience of the issues involved in implementing distributed real-time control over large distances, a prototype local orbit feedback system is being developed in the SPS. This will use 6 pickups, each equipped with the full LHC acquisition electronics chain and linked to a real-time communication and feedback system. This reports summarises the .rst tests performed with this system in October 2002, where the data from four pickups was successfully acquired and displayed at 10 Hz in the control room.

Differential transcriptional regulation of banana sucrose phosphate synthase gene in response to ethylene, auxin, wounding, low temperature and different photoperiods during fruit ripening and functional analysis of banana SPS gene promoter.

Science.gov (United States)

Roy Choudhury, Swarup; Roy, Sujit; Das, Ranjan; Sengupta, Dibyendu N

2008-12-01

Sucrose phosphate synthase (SPS) (EC 2.3.1.14) is the key regulatory component in sucrose formation in banana (Musa acuminata subgroup Cavendish, cv Giant governor) fruit during ripening. This report illustrates differential transcriptional responses of banana SPS gene following ethylene, auxin, wounding, low temperature and different photoperiods during ripening in banana fruit. Whereas ethylene strongly stimulated SPS transcript accumulation, auxin and cold treatment only marginally increased the abundance of SPS mRNA level, while wounding negatively regulated SPS gene expression. Conversely, SPS transcript level was distinctly increased by constant exposure to white light. Protein level, enzymatic activity of SPS and sucrose synthesis were substantially increased by ethylene and increased exposure to white light conditions as compared to other treatments. To further study the transcriptional regulation of SPS in banana fruit, the promoter region of SPS gene was cloned and some cis-acting regulatory elements such as a reverse GCC-box ERE, two ARE motifs (TGTCTC), one LTRE (CCGAA), a GAGA-box (GAGA...) and a GATA-box LRE (GATAAG) were identified along with the TATA and CAAT-box. DNA-protein interaction studies using these cis-elements indicated a highly specific cis-trans interaction in the banana nuclear extract. Furthermore, we specifically studied the light responsive characteristics of GATA-box containing synthetic as well as native banana SPS promoter. Transient expression assays using banana SPS promoter have also indicated the functional importance of the SPS promoter in regulating gene expression. Together, these results provide insights into the transcriptional regulation of banana SPS gene in response to phytohormones and other environmental factors during fruit ripening.

Optics Measurements and Matching of TT2-TT10 Line for Injection of the LHC Beam in the SPS

CERN Document Server

Benedetto, E; Guerrero, A; Jacquet, D

2008-01-01

A well matched injection in the SPS is very important for preserving the emittance of the LHC beam. The paper presents the algorithms used for the analysis and the results of the optics measurements done in the transfer line TT2-TT10 and in the SPS. The dispersion is computed by varying the beam momentum and recording the offsets at the BPMs, while the Twiss parameters and emittance measurements in TT2-TT10 are performed with beam profile monitors equipped with OTR screens. These results are completed by those obtained with a matching monitor installed in the SPS as a prototype for the LHC. This device makes use of an OTR screen and a fast acquisition system, to get the turn by turn beam profiles right at injection in the ring, from which the beam mismatch is computed and compared with the results obtained in the line. Finally, on the basis of such measurements, a betatron and dispersion matching of TT2-TT10 for injection in the SPS has been performed and successfully put in operation.

Preliminary environmental assessment for the Satellite Power System (SPS). Revision 1. Volume 2. Detailed assessment

Energy Technology Data Exchange (ETDEWEB)

1980-01-01

The Department of Energy (DOE) is considering several options for generating electrical power to meet future energy needs. The satellite power system (SPS), one of these options, would collect solar energy through a system of satellites in space and transfer this energy to earth. A reference system has been described that would convert the energy to microwaves and transmit the microwave energy via directive antennas to large receiving/rectifying antennas (rectennas) located on the earth. At the rectennas, the microwave energy would be converted into electricity. The potential environmental impacts of constructing and operating the satellite power system are being assessed as a part of the Department of Energy's SPS Concept Development and Evaluation Program. This report is Revision I of the Preliminary Environmental Assessment for the Satellite Power System published in October 1978. It refines and extends the 1978 assessment and provides a basis for a 1980 revision that will guide and support DOE recommendations regarding future SPS development. This is Volume 2 of two volumes. It contains the technical detail suitable for peer review and integrates information appearing in documents referenced herein. The key environmental issues associated with the SPS concern human health and safety, ecosystems, climate, and electromagnetic systems interactions. In order to address these issues in an organized manner, five tasks are reported: (I) microwave-radiation health and ecological effects; (II) nonmicrowave health and ecological effectss; (III) atmospheric effects; (IV) effects on communication systems due to ionospheric disturbance; and (V) electromagnetic compatibility. (WHK)

Comparative results on collimation of the SPS beam of protons and Pb ions with bent crystals

CERN Document Server

Scandale, W.; Assmann, R.; Bracco, C.; Cerutti, F.; Christiansen, J.; Gilardoni, S.; Laface, E.; Losito, R.; Masi, A.; Metral, E.; Mirarchi, D.; Montesano, S.; Previtali, V.; Redaelli, S.; Valentino, G.; Schoofs, P.; Smirnov, G.; Tlustos, L.; Bagli, E.; Baricordi, S.; Dalpiaz, P.; Guidi, V.; Mazzolari, A.; Vincenzi, D.; Dabagov, S.; Murtas, F.; Carnera, A.; Della Mea, G.; De Salvador, D.; Lombardi, A.; Lytovchenko, O.; Tonezzer, M.; Cavoto, G.; Ludovici, L.; Santacesaria, R.; Valente, P.; Galluccio, F.; Afonin, A.G.; Bulgakov, M.K.; Chesnokov, Yu.A.; Maisheev, V.A.; Yazynin, I.A.; Kovalenko, A.D.; Taratin, A.M.; Uzhinskiy, V.V.; Gavrikov, Yu.A.; Ivanov, Yu.M.; Lapina, L.P.; Skorobogatov, V.V.; Ferguson, W.; Fulcher, J.; Hall, G.; Pesaresi, M.; Raymond, M.; Rose, A.; Ryan, M.; Zorba, O.; Robert-Demolaize, G.; Markiewicz, T.; Oriunno, M.; Wienands, U.

2011-01-01

New experiments on crystal assisted collimation have been carried out at the CERN SPS with stored beams of 120 Gev/c protons and Pb ions. Bent silicon crystals of 2 mm long with about 170 mu rad bend angle and a small residual torsion were used as primary collimators. In channeling conditions, the beam loss rate induced by inelastic interactions of particles with the crystal nuclei is minimal. The loss reduction was about 6 for protons and about 3 for Pb ions. Lower reduction value for Pb ions can be explained by their considerably larger ionization losses in the crystal. In one of the crystals, the measured fraction of the Pb ion beam halo deflected in channeling conditions was 74\\%, a value very close to that for protons. The intensity of the off-momentum halo leaking out from the collimation station was measured in the first high dispersion area downstream. The particle population in the shadow of the secondary collimator-absorber was considerably smaller in channeling conditions than for amorphous orienta...

Synthesis and characterization of sulfonate polystyrene-lignosulfonate-alumina (SPS-LS-Al{sub 2}O{sub 3}) polyblends as electrolyte membranes for fuel cell

Energy Technology Data Exchange (ETDEWEB)

Gonggo, Siang Tandi, E-mail: standigonggo@yahoo.com [Chemistry Research Groups, Faculty of Teacher Training and Educational Sciences, Tadulako University (Indonesia)

2015-09-30

The new type of electrolyte membrane materials has been prepared by blend sulfonated polystyrene (SPS), lignosulfonate (LS), and alumina (SPS-LS-Al{sub 2}O{sub 3}) by casting polymer solution. The resulting polymer electrolyte membranes were then characterized by functional groups analysis, mechanical properties, water uptake, ion exchange capacity, and proton conductivity. SPS-LS-Al{sub 2}O{sub 3} membranes with alumina composition various have been proven qualitatively by analysis of functional groups. Increasing the Al{sub 2}O{sub 3} ratio resulted in higher ion exchange capacity (IEC), mechanical strength and proton conductivity, but water uptake decreased. The SPS-LS-Al{sub 2}O{sub 3} blend showed higher proton conductivity than Nafion 117.

Satellite Power Systems (SPS) concept definition study, exhibit C. Volume 2, part 1: System engineering

Science.gov (United States)

Hanley, G. M.

1979-01-01

Volume 2, Part 1, of a seven volume report is presented. Part 1 encompasses Satellite Power Systems (SPS) systems engineering aspects and is divided into three sections. The first section presents descriptions of the various candidate concepts considered and conclusions and recommendations for a preferred concept. The second section presents a summary of results of the various trade studies and analysis conducted during the course of the study. The third section describes the Photovoltaic Satellite Based Satellite Power System (SPS) Point Design as it was defined through studies performed during the period January 1977 through March 1979.

SPS-ALPHA: The First Practical Solar Power Satellite via Arbitrarily Large PHased Array

Data.gov (United States)

National Aeronautics and Space Administration — SPS-ALPHA (Solar Power Satellite via Arbitrarily Large Phased Array) is a novel, bio-mimetic approach to the challenge of space solar power. If successful, this...

Electron cloud in the CERN accelerators (PS, SPS, LHC)

International Nuclear Information System (INIS)

Iadarola, G; Rumolo, G

2013-01-01

Several indicators have pointed to the presence of an Electron Cloud (EC) in some of the CERN accelerators, when operating with closely spaced bunched beams. In particular, spurious signals on the pick ups used for beam detection, pressure rise and beam instabilities were observed at the Proton Synchrotron (PS) during the last stage of preparation of the beams for the Large Hadron Collider (LHC), as well as at the Super Proton Synchrotron (SPS). Since the LHC has started operation in 2009, typical electron cloud phenomena have appeared also in this machine, when running with trains of closely packed bunches (i.e. with spacings below 150ns). Beside the above mentioned indicators, other typical signatures were seen in this machine (due to its operation mode and/or more refined detection possibilities), like heat load in the cold dipoles, bunch dependent emittance growth and degraded lifetime in store and bunch-by-bunch stable phase shift to compensate for the energy loss due to the electron cloud. An overview of the electron cloud status in the different CERN machines (PS, SPS, LHC) will be presented in this paper, with a special emphasis on the dangers for future operation with more intense beams and the necessary countermeasures to mitigate or suppress the effect. (author)

Optimization of rotational arc station parameter optimized radiation therapy

Energy Technology Data Exchange (ETDEWEB)

Dong, P.; Ungun, B. [Department of Radiation Oncology, Stanford University, Stanford, California 94305 (United States); Boyd, S. [Department of Electrical Engineering, Stanford University, Stanford, California 94305 (United States); Xing, L., E-mail: lei@stanford.edu [Department of Radiation Oncology, Stanford University, Stanford, California 94305 and Department of Electrical Engineering, Stanford University, Stanford, California 94305 (United States)

2016-09-15

Purpose: To develop a fast optimization method for station parameter optimized radiation therapy (SPORT) and show that SPORT is capable of matching VMAT in both plan quality and delivery efficiency by using three clinical cases of different disease sites. Methods: The angular space from 0° to 360° was divided into 180 station points (SPs). A candidate aperture was assigned to each of the SPs based on the calculation results using a column generation algorithm. The weights of the apertures were then obtained by optimizing the objective function using a state-of-the-art GPU based proximal operator graph solver. To avoid being trapped in a local minimum in beamlet-based aperture selection using the gradient descent algorithm, a stochastic gradient descent was employed here. Apertures with zero or low weight were thrown out. To find out whether there was room to further improve the plan by adding more apertures or SPs, the authors repeated the above procedure with consideration of the existing dose distribution from the last iteration. At the end of the second iteration, the weights of all the apertures were reoptimized, including those of the first iteration. The above procedure was repeated until the plan could not be improved any further. The optimization technique was assessed by using three clinical cases (prostate, head and neck, and brain) with the results compared to that obtained using conventional VMAT in terms of dosimetric properties, treatment time, and total MU. Results: Marked dosimetric quality improvement was demonstrated in the SPORT plans for all three studied cases. For the prostate case, the volume of the 50% prescription dose was decreased by 22% for the rectum and 6% for the bladder. For the head and neck case, SPORT improved the mean dose for the left and right parotids by 15% each. The maximum dose was lowered from 72.7 to 71.7 Gy for the mandible, and from 30.7 to 27.3 Gy for the spinal cord. The mean dose for the pharynx and larynx was

Optimization of rotational arc station parameter optimized radiation therapy

International Nuclear Information System (INIS)

Dong, P.; Ungun, B.; Boyd, S.; Xing, L.

2016-01-01

Purpose: To develop a fast optimization method for station parameter optimized radiation therapy (SPORT) and show that SPORT is capable of matching VMAT in both plan quality and delivery efficiency by using three clinical cases of different disease sites. Methods: The angular space from 0° to 360° was divided into 180 station points (SPs). A candidate aperture was assigned to each of the SPs based on the calculation results using a column generation algorithm. The weights of the apertures were then obtained by optimizing the objective function using a state-of-the-art GPU based proximal operator graph solver. To avoid being trapped in a local minimum in beamlet-based aperture selection using the gradient descent algorithm, a stochastic gradient descent was employed here. Apertures with zero or low weight were thrown out. To find out whether there was room to further improve the plan by adding more apertures or SPs, the authors repeated the above procedure with consideration of the existing dose distribution from the last iteration. At the end of the second iteration, the weights of all the apertures were reoptimized, including those of the first iteration. The above procedure was repeated until the plan could not be improved any further. The optimization technique was assessed by using three clinical cases (prostate, head and neck, and brain) with the results compared to that obtained using conventional VMAT in terms of dosimetric properties, treatment time, and total MU. Results: Marked dosimetric quality improvement was demonstrated in the SPORT plans for all three studied cases. For the prostate case, the volume of the 50% prescription dose was decreased by 22% for the rectum and 6% for the bladder. For the head and neck case, SPORT improved the mean dose for the left and right parotids by 15% each. The maximum dose was lowered from 72.7 to 71.7 Gy for the mandible, and from 30.7 to 27.3 Gy for the spinal cord. The mean dose for the pharynx and larynx was

Physics at the AD/PS/SPS (3/4)

CERN Multimedia

CERN. Geneva

2012-01-01

Lecture 3: Flavour and Neutrinos The CERN SPS provides kaon and neutrino beams which are unique in the world. The lecture will describe the flavour and neutrino research conducted with these beams. The flavour programme is centered around the study of kaons. It includes a broad spectrum of topics such as CP-Violation, the precise determination of quark-mixing parameters, lepton universality and very rare decays. The CNGS neutrino beam enables to perform long baseline neutrino oscillation experiments with unique features such as the tau lepton appearance.

SPS RF Accelerating Cavity

CERN Multimedia

1979-01-01

This picture shows one of the 2 new cavities installed in 1978-1979. The main RF-system of the SPS comprises four cavities: two of 20 m length and two of 16.5 m length. They are all installed in one long straight section (LSS 3). These cavities are of the travelling-wave type operating at a centre frequency of 200.2 MHz. They are wideband, filling time about 700 ns and untuned. The power amplifiers, using tetrodes are installed in a surface building 200 m from the cavities. Initially only two cavities were installed, a third cavity was installed in 1978 and a forth one in 1979. The number of power amplifiers was also increased: to the first 2 MW plant a second 2 MW plant was added and by end 1979 there were 8 500 kW units combined in pairs to feed each of the 4 cavities with up to about 1 MW RF power, resulting in a total accelerating voltage of about 8 MV. See also 7412016X, 7412017X, 7411048X

How dense does parton matter get in Pb + Pb collisions at the CERN SPS?

International Nuclear Information System (INIS)

Geiger, K.; Mueller, B.

1998-01-01

The qualitative features of parton production through materialization in heavy-ion collisions are examined within perturbative QCD, and the magnitude of the resulting parton density created during the early stage of the collisions is estimated. The implications for 'anomalous' J/ψ suppression observed in Pb + Pb collisions at the CERN SPS are discussed. The A-dependence of absorption of J/ψ by (partonic) comovers is steeper than assumed in most phenomenological models, because the absorption process is dominated by quasi-perturbative QCD interactions. The argument is supported by results recently obtained in the framework of the parton cascade model. Significant 'anomalous' suppression for Pb + Pb collisions at the CERN-SPS are predicted, but not for S + U collisions. (author)

NA62 experiment at CERN SPS

Directory of Open Access Journals (Sweden)

Kozhuharov Venelin

2014-01-01

Full Text Available The NA62 experiment at SPS is a continuation of the long standing CERN kaon physics program. The high statistics and the unprecedent precision allow to probe the Standard Model and test the description of the strong interactions at low energy. The final results on the the lepton universality test by measuring the ratio RK = Γ(K+ → e+ν/Γ(K+ → µ+ν and the study of the K± → π±γγ decay are presented. The major goal of the NA62 experiment is to perform a measurement of the Br(K+ → π+νν̄ with a precision of 10% in two years of data taking. The detector setup together with the analysis technique is described.

Observation of strong leakage reduction in crystal assisted collimation of the SPS beam

Energy Technology Data Exchange (ETDEWEB)

Scandale, W. [CERN, European Organization for Nuclear Research, CH-1211 Geneva 23 (Switzerland); Laboratoire de l' Accelerateur Lineaire (LAL), Universite Paris Sud Orsay, Orsay (France); INFN Sezione di Roma, Piazzale Aldo Moro 2, 00185 Rome (Italy); Arduini, G.; Butcher, M.; Cerutti, F.; Garattini, M.; Gilardoni, S.; Lechner, A.; Losito, R.; Masi, A.; Mereghetti, A.; Metral, E. [CERN, European Organization for Nuclear Research, CH-1211 Geneva 23 (Switzerland); Mirarchi, D. [CERN, European Organization for Nuclear Research, CH-1211 Geneva 23 (Switzerland); Imperial College, London (United Kingdom); Montesano, S.; Redaelli, S. [CERN, European Organization for Nuclear Research, CH-1211 Geneva 23 (Switzerland); Rossi, R. [CERN, European Organization for Nuclear Research, CH-1211 Geneva 23 (Switzerland); INFN Sezione di Roma, Piazzale Aldo Moro 2, 00185 Rome (Italy); Schoofs, P.; Smirnov, G. [CERN, European Organization for Nuclear Research, CH-1211 Geneva 23 (Switzerland); Bagli, E.; Bandiera, L.; Baricordi, S. [INFN Sezione di Ferrara, Dipartimento di Fisica, Università di Ferrara, Ferrara (Italy); and others

2015-09-02

In ideal two-stage collimation systems, the secondary collimator–absorber should have its length sufficient to exclude practically the exit of halo particles with large impact parameters. In the UA9 experiments on the crystal assisted collimation of the SPS beam a 60 cm long tungsten bar is used as a secondary collimator–absorber which is insufficient for the full absorption of the halo protons. Multi-turn simulation studies of the collimation allowed to select the position for the beam loss monitor downstream the collimation area where the contribution of particles deflected by the crystal in channeling regime but emerging from the secondary collimator–absorber is considerably reduced. This allowed observation of a strong leakage reduction of halo protons from the SPS beam collimation area, thereby approaching the case with an ideal absorber.

Optics Measurements and Matching of TT2-TT10 Line for Injection of the LHC Beam in the SPS

CERN Document Server

Benedetto, E

2008-01-01

A well matched injection in the SPS is very important for preserving the emittance of the LHC beam. The paper presents the algorithms used for the analysis and the results of the 2007 optics measurements campaign done in the transfer line TT2-TT10 and in the SPS. The dispersion is computed by varying the beam momentum and recording the offsets at the BPMs, while the Twiss parameters and emittance measurements in TT2-TT10 are performed with beam profile monitors equipped with OTR screens. Finally, on the basis of such measurements, a betatron and dispersion matching of TT2-TT10 for injection in the SPS has been performed and successfully put in operation since October 2007.

Search for the quark-gluon plasma (1989): The NA35 experiment at the CERN SPS

International Nuclear Information System (INIS)

Pugh, H.G.

1989-09-01

Results from the NA35 experiment at the CERN SPS are described in the context of possible formation and identification of a quark-gluon plasma (QGP). Evidence is presented that the initial energy density and temperature are sufficient for the QGP to be produced, and that hydrodynamic flow occurs in the expansion stage. Evidence for an unexpectedly large pion source size and for enhanced strangeness production is presented, and discussed in terms of QGP formation. Plans for experiments in 1990--91 with an expanded set up are presented, and prospects for a program with Pb beams at the SPS are discussed. 39 refs., 12 figs

Feasibility study of stochastic cooling of bunches in the SPS

International Nuclear Information System (INIS)

Boussard, D.; Chattopadhyay, S.; Dome, G.; Linnecar, T.

1984-01-01

The average luminosity of the SPS collider could be improved if the slow blow-up of transverse emittances due to beam-beam and intrabeam scattering effects were to be reduced by a transverse cooling system. We examine the parameters of such a system and propose a technological approach which seems better suited to the case of a few bunches circulating in a large machine. (orig./HSI)

Dileptons and photons from central heavy-ion collisions at CERN-SPS

CERN Document Server

Kämpfer, B; Pavlenko, O P; Gale, C

2002-01-01

A unique parameterization of secondary (thermal) dilepton and photon yields in heavy-ion experiments at CERN-SPS is proposed. Adding those thermal yields to background contributions the spectral shapes of the CERES/NA45, NA38, NA50, HELIOS/3 and WA98 data from experiments with lead and sulfur beams can be well described.

Social anxiety in the general population: introducing abbreviated versions of SIAS and SPS.

Science.gov (United States)

Kupper, Nina; Denollet, Johan

2012-01-01

Social anxiety is characterized by the experience of stress, discomfort and fear in social situations, and is associated with substantial personal and societal burden. Two questionnaires exist that assess the aspects of social anxiety, i.e. social interaction anxiety (SIAS) and social phobia (SPS). There is no agreement in literature on the dimensionality of social anxiety. Further, the length of a questionnaire may negatively affect response rates and participation at follow-up occasions. To explore the structure of social anxiety in the general population, and to examine psychosocial and sociodemographic correlates. Our second aim was to construct abbreviated versions of SIAS and SPS that can be easily used and with minimal burden. A total of 1598 adults from the general Dutch population completed a survey asking information on social anxiety, mood and demographics. Exploratory and confirmatory factor analyses as well as reliability analysis with item-total statistics were performed. Confirmatory factor analysis revealed a 3-factor structure for social phobia, and a 2-factor structure for the SIAS, with the second factor containing both reversely scored items. The abbreviated versions of SPS (11 items) and SIAS (10 items) show excellent discriminant and construct validity (Cronbach's α=.90 and .92), while specificity analysis showed that gender, marital status and educational level (SIAS(10): pSIAS, reducing the questionnaire burden for participants in epidemiological and biobehavioral research. Copyright © 2011 Elsevier B.V. All rights reserved.

Scaling of charged particle multiplicity in Pb-Pb collisions at SPS energies

CERN Document Server

Abreu, M C; Alexa, C; Arnaldi, R; Ataian, M R; Baglin, C; Baldit, A; Bedjidian, Marc; Beolè, S; Boldea, V; Bordalo, P; Borges, G; Bussière, A; Capelli, L; Castanier, C; Castor, J I; Chaurand, B; Chevrot, I; Cheynis, B; Chiavassa, E; Cicalò, C; Claudino, T; Comets, M P; Constans, N; Constantinescu, S; Cortese, P; De Falco, A; De Marco, N; Dellacasa, G; Devaux, A; Dita, S; Drapier, O; Ducroux, L; Espagnon, B; Fargeix, J; Force, P; Gallio, M; Gavrilov, Yu K; Gerschel, C; Giubellino, P; Golubeva, M B; Gonin, M; Grigorian, A A; Grigorian, S; Grossiord, J Y; Guber, F F; Guichard, A; Gulkanian, H R; Hakobyan, R S; Haroutunian, R; Idzik, M; Jouan, D; Karavitcheva, T L; Kluberg, L; Kurepin, A B; Le Bornec, Y; Lourenço, C; Macciotta, P; MacCormick, M; Marzari-Chiesa, A; Masera, M; Masoni, A; Monteno, M; Musso, A; Petiau, P; Piccotti, A; Pizzi, J R; Prado da Silva, W L; Prino, F; Puddu, G; Quintans, C; Ramello, L; Ramos, S; Rato-Mendes, P; Riccati, L; Romana, A; Santos, H; Saturnini, P; Scalas, E; Scomparin, E; Serci, S; Shahoyan, R; Sigaudo, F; Silva, S; Sitta, M; Sonderegger, P; Tarrago, X; Topilskaya, N S; Usai, G L; Vercellin, Ermanno; Villatte, L; Willis, N

2002-01-01

The charged particle multiplicity distribution $dN_{ch}/d\\eta$ has been measured by the NA50 experiment in Pb--Pb collisions at the CERN SPS. Measurements were done at incident energies of 40 and 158 GeV per nucleon over a broad impact parameter range. The multiplicity distributions are studied as a function of centrality using the number of participating nucleons ($N_{part}$), or the number of binary nucleon--nucleon collisions ($N_{coll}$). Their values at midrapidity exhibit a power law scaling behaviour given by $N_{part}^{1.00}$ and $N_{coll}^{0.75}$ at 158 GeV. Compatible results are found for the scaling behaviour at 40 GeV. The width of the $dN_{ch}/d\\eta$ distributions is larger at 158 than at 40 GeV/nucleon and decreases slightly with centrality at both energies. Our results are compared to similar studies performed by other experiments both at the CERN SPS and at RHIC.}

Environmental assessment for the Satellite Power System (SPS) Concept Development and Evaluation Program (CDEP). [Microwave and non-microwave health and ecological assessment

Energy Technology Data Exchange (ETDEWEB)

Valentino, A.R.

1980-08-01

In the satellite power system (SPS), satellites in geosynchronous earth orbit would collect solar energy in space, convert it to microwaves, and transmit the microwaves to receiving antennas (rectennas) on earth. At the rectennas, the microwave energy would be converted to electricity. This SPS environmental assessment considers the microwave and nonmicrowave effects on the terrestrial environment and human health, atmospheric effects, and effects on electromagnetic systems. No environmental problem has been identified that would preclude the continued study of SPS technology. To increase the certainty of the assessment, some research has been initiated and long-term research is being planned.

Tilted bending magnet for SPS target area TCC2

CERN Multimedia

CERN PhotoLab

1976-01-01

A slow-extracted proton beam from the SPS goes to the underground target zone TCC2. The part of the primary beam which traverses target T4 is recuperated and transported over some 800 m, for further use in the North Area High Intensity facility (NAHIF). The curved and sloped trajectory required 4 of the bending magnets to be tilted. Here we see one of them being attended by Gilbert Françon in hall 867, ready for installation in TCC2.

Optics measurements and transfer line matching for the SPS injection of the CERN Multi-Turn Extraction beam

CERN Document Server

Benedetto, E; Cettour Cave, S; Follin, F; Gilardoni, S; Giovannozzi, M; Roncarolo, F

2010-01-01

Dispersion and beam optics measurements were carried out in the transfer line between the CERN PS and SPS for the new Multi-Turn Extraction beam. Since the extraction conditions of the four islands and the core are different and strongly dependent on the non-linear effects used to split the beam in the transverse plane, a special care was taken during the measurement campaigns. Furthermore, an appropriate strategy was devised to minimize the overall optical mismatch at SPS injection. All this led to a new optical configuration that will be presented in the paper.

Temporary tattoos: a novel OSCE assessment tool.

Science.gov (United States)

Gormley, Gerry; Menary, Allison; Layard, Brooke; Hart, Nigel; McCourt, Collette

2013-08-01

There are many issues regarding the use of real patients in objective structured clinical examinations (OSCEs). In dermatology OSCE stations, standardised patients (SPs) with clinical photographs are often used. Temporary transfer tattoos can potentially simulate skin lesions when applied to an SP. This study aims to appraise the use of temporary malignant melanoma tattoos within an OSCE framework. Within an 11-station OSCE, a temporary malignant melanoma tattoo was developed and applied to SPs in a 'skin lesion' OSCE station. A questionnaire captured the opinions of the candidate, SP and examiners, and the degree of perceived realism of each station was determined. Standard post hoc OSCE analysis determined the psychometric reliability of the stations. The response rates were 95.9 per cent of candidates and 100 per cent of the examiners and SPs. The 'skin lesion' station achieved the highest realism score compared with other stations: 89.0 per cent of candidates felt that the skin lesion appeared realistic; only 28 per cent of candidates had ever seen a melanoma before in training. The psychometric performance of the melanoma station was comparable with, and in many instances better than, other OSCE stations. Transfer tattoo technology facilitates a realistic dermatology OSCE station encounter. Temporary tattoos, alongside trained SPs, provide an authentic, standardised and reliable experience, allowing the assessment of integrated dermatology clinical skills. © 2013 John Wiley & Sons Ltd.

Energy and system size dependence of Ξ- and anti Ξ+ production in relativistic heavy-ion collisions at the CERN SPS

International Nuclear Information System (INIS)

Mitrovski, M.K.

2007-01-01

The strong nuclear force is described by Quantum Chromodynamics (QCD), the parallel field theory to Quantum Electrodynamics (QED) that describes the electromagnetic force. It is propagated by gluons analogously to photons in the electromagnetic force, but unlike photons, which do not carry electric charge, gluons carry color, and they can self-interact. However, as individual quarks have never been observed in nature, it is postulated that the color charge itself is confined, and hence all baryons and mesons must be colorless objects. To study nuclear matter under extreme conditions, it is necessary to create hot and dense nuclear matter in the laboratory. In such conditions the confinement between quarks and gluons is cancelled (deconfinement). This state is characterized with a quasi-free behavior of quarks and gluons. The strange (s) and anti-strange (anti-s) quarks are not contained in the colliding nuclei, but are newly produced and show up in the strange hadrons in the final state. It was suggested that strange particle production is enhanced in the QGP with respect to that in a hadron gas. This enhancement is relative to a collision where a transition to a QGP phase does not take place, such as p+p collisions where the system size is very small. Therefore the energy- and system size dependence is studied to receive a picture about the initial state. In this thesis experimental results on the energy- and system size dependence of Xi hyperon production at the CERN SPS is shown. All measurements were performed with the NA49 detector at the CERN SPS. NA49 took central lead-lead collisions from 20 - 158 AGeV, minimus bias lead-lead collisions at 40 and 158 AGeV, and semi-central silicon-silicon collisions at 158 AGeV. The NA49 experiment features a large acceptance in the forward hemisphere allowing for measurements of Xi rapidity spectra. At the SPS accelerator at CERN Pb+Pb collisions are performed with beam energies to 158 AGeV. The analyzed data sets were

Alignment and girder position of MSE septa in the new LSS4 extraction channel of the SPS

CERN Document Server

Balhan, B; Rizzo, A; Weterings, W; CERN. Geneva. SPS and LHC Division

2002-01-01

For the extraction of the beam from the Super Proton Synchrotron (SPS) to ring 2 of the Large Hadron Collider (LHC) and the CERN Neutrino to Gran Sasso (CNGS)facility, a new fast-extraction system is being constructed in the long straight section LSS4 of the SPS. Besides extraction bumpers, enlarged aperture quadrupoles and extraction kicker magnets (MKE), six conventional DC septum magnets (MSE) are used. These magnets are mounted on a single rigid support girder, pre-aligned so as to follow the trajectory of the extracted beam and optimise the available aperture. The girder has been motorised in order to optimise the local SPS aperture during setting up, so as to avoid the risk of circulating beam impact on the septum coils. In this note, we briefly present the trajectory and apertures of the beam, we describe the calculations and methods that have been used to determine the magnet position on the girder, and finally we report on the details of the girder movement and alignment.

Excitation function of particle production from SIS/Bevalac to SPS energies; evidence for a phase transition?

CERN Document Server

Ströbele, H

2005-01-01

The second part of the title is meant as an incentive to scrutinize the data which will be presented in the following. If the threshold for creating the QGP in nuclear collisions is located in the SPS energy range, it will become evident only by carefully scanning energy and mass dependences of many observables and identifying non monotonous behaviour of several quantities consistently. This contribution, which is a sort of short update of an earlier article, is meant to review the current data on particle production in terms of total yields and ratios, as well transverse and longitudinal kinematical distributions from threshold up to SPS energies.

PROSPECTS AND FEATURES OF BIOGASOLINE STATIONS

OpenAIRE

Grigorash O. V.; Kvitko A. V.; Koshko A. R.

2015-01-01

The article deals with one of the promising areas belonging to energy-saving technologies; it is the introduction of biogasoline stations into agricultural production. The analysis of the application in the world has been shown. To determine the cost-effectiveness of biogasoline stations we have shown the data for the calculation of the potential of biomass: organic waste settlements; animal waste; waste of poultry; crop residues; waste processing industry. We have obtained graphic dependence...

International collaborative study of the endogenous reference gene, sucrose phosphate synthase (SPS), used for qualitative and quantitative analysis of genetically modified rice.

Science.gov (United States)

Jiang, Lingxi; Yang, Litao; Zhang, Haibo; Guo, Jinchao; Mazzara, Marco; Van den Eede, Guy; Zhang, Dabing

2009-05-13

One rice ( Oryza sativa ) gene, sucrose phosphate synthase (SPS), has been proven to be a suitable endogenous reference gene for genetically modified (GM) rice detection in a previous study. Herein are the reported results of an international collaborative ring trial for validation of the SPS gene as an endogenous reference gene and its optimized qualitative and quantitative polymerase chain reaction (PCR) systems. A total of 12 genetically modified organism (GMO) detection laboratories from seven countries participated in the ring trial and returned their results. The validated results confirmed the species specificity of the method through testing 10 plant genomic DNAs, low heterogeneity, and a stable single-copy number of the rice SPS gene among 7 indica varieties and 5 japonica varieties. The SPS qualitative PCR assay was validated with a limit of detection (LOD) of 0.1%, which corresponded to about 230 copies of haploid rice genomic DNA, while the limit of quantification (LOQ) for the quantitative PCR system was about 23 copies of haploid rice genomic DNA, with acceptable PCR efficiency and linearity. Furthermore, the bias between the test and true values of eight blind samples ranged from 5.22 to 26.53%. Thus, we believe that the SPS gene is suitable for use as an endogenous reference gene for the identification and quantification of GM rice and its derivates.

Installation and management of the SPS and LEP control system computers

International Nuclear Information System (INIS)

Bland, Alastair

1994-01-01

Control of the CERN SPS and LEP accelerators and service equipment on the two CERN main sites is performed via workstations, file servers, Process Control Assemblies (PCAs) and Device Stub Controllers (DSCs). This paper describes the methods and tools that have been developed to manage the file servers, PCAs and DSCs since the LEP startup in 1989. There are five operational DECstation 5000s used as file servers and boot servers for the PCAs and DSCs. The PCAs consist of 90 SCO Xenix 386 PCs, 40 LynxOS 486 PCs and more than 40 older NORD 100s. The DSCs consist of 90 OS-968030 VME crates and 10 LynxOS 68030 VME crates. In addition there are over 100 development systems. The controls group is responsible for installing the computers, starting all the user processes and ensuring that the computers and the processes run correctly. The operators in the SPS/LEP control room and the Services control room have a Motif-based X window program which gives them, in real time, the state of all the computers and allows them to solve problems or reboot them. ((orig.))

SPS measures and possible market access implications for agricultural trade in the Doha Round: An analysis of systemic issues

OpenAIRE

Murali Kallummal

2012-01-01

Even as the Doha Round seeks to address tariff liberalization issues in a comprehensive manner, the imbalance in the outcome of market access for developing country exporters will be particularly glaring in the case of fresh agricultural and processed food products. There is growing evidence that protectionism from the usage of non-tariff barriers such as SPS measures has increased tremendously in the recent past. This paper discusses an analysis of the SPS notifications made by WTO Member co...

WE-AB-209-09: Optimization of Rotational Arc Station Parameter Optimized Radiation Therapy

Energy Technology Data Exchange (ETDEWEB)

Dong, P; Xing, L [Stanford University School of Medicine, Stanford, CA (United States); Ungun, B [Stanford University School of Medicine, Stanford, CA (United States); Stanford University School of Engineering, Stanford, CA (United States); Boyd, S [Stanford University School of Engineering, Stanford, CA (United States)

2016-06-15

Purpose: To develop a fast optimization method for station parameter optimized radiation therapy (SPORT) and show that SPORT is capable of improving VMAT in both plan quality and delivery efficiency. Methods: The angular space from 0° to 360° was divided into 180 station points (SPs). A candidate aperture was assigned to each of the SPs based on the calculation results using a column generation algorithm. The weights of the apertures were then obtained by optimizing the objective function using a state-of-the-art GPU based Proximal Operator Graph Solver (POGS) within seconds. Apertures with zero or low weight were thrown out. To avoid being trapped in a local minimum, a stochastic gradient descent method was employed which also greatly increased the convergence rate of the objective function. The above procedure repeated until the plan could not be improved any further. A weighting factor associated with the total plan MU also indirectly controlled the complexities of aperture shapes. The number of apertures for VMAT and SPORT was confined to 180. The SPORT allowed the coexistence of multiple apertures in a single SP. The optimization technique was assessed by using three clinical cases (prostate, H&N and brain). Results: Marked dosimetric quality improvement was demonstrated in the SPORT plans for all three studied cases. Prostate case: the volume of the 50% prescription dose was decreased by 22% for the rectum. H&N case: SPORT improved the mean dose for the left and right parotids by 15% each. Brain case: the doses to the eyes, chiasm and inner ears were all improved. SPORT shortened the treatment time by ∼1 min for the prostate case, ∼0.5 min for brain case, and ∼0.2 min for the H&N case. Conclusion: The superior dosimetric quality and delivery efficiency presented here indicates that SPORT is an intriguing alternative treatment modality.

WE-AB-209-09: Optimization of Rotational Arc Station Parameter Optimized Radiation Therapy

International Nuclear Information System (INIS)

Dong, P; Xing, L; Ungun, B; Boyd, S

2016-01-01

Purpose: To develop a fast optimization method for station parameter optimized radiation therapy (SPORT) and show that SPORT is capable of improving VMAT in both plan quality and delivery efficiency. Methods: The angular space from 0° to 360° was divided into 180 station points (SPs). A candidate aperture was assigned to each of the SPs based on the calculation results using a column generation algorithm. The weights of the apertures were then obtained by optimizing the objective function using a state-of-the-art GPU based Proximal Operator Graph Solver (POGS) within seconds. Apertures with zero or low weight were thrown out. To avoid being trapped in a local minimum, a stochastic gradient descent method was employed which also greatly increased the convergence rate of the objective function. The above procedure repeated until the plan could not be improved any further. A weighting factor associated with the total plan MU also indirectly controlled the complexities of aperture shapes. The number of apertures for VMAT and SPORT was confined to 180. The SPORT allowed the coexistence of multiple apertures in a single SP. The optimization technique was assessed by using three clinical cases (prostate, H&N and brain). Results: Marked dosimetric quality improvement was demonstrated in the SPORT plans for all three studied cases. Prostate case: the volume of the 50% prescription dose was decreased by 22% for the rectum. H&N case: SPORT improved the mean dose for the left and right parotids by 15% each. Brain case: the doses to the eyes, chiasm and inner ears were all improved. SPORT shortened the treatment time by ∼1 min for the prostate case, ∼0.5 min for brain case, and ∼0.2 min for the H&N case. Conclusion: The superior dosimetric quality and delivery efficiency presented here indicates that SPORT is an intriguing alternative treatment modality.

The SPS Beam quality monitor, from design to operation

CERN Document Server

Papotti, G; Follin, F; Shaposhnikova, E

2011-01-01

The SPS Beam Quality Monitor is a system that monitors longitudinal beam parameters on a cycle-by-cycle basis and prevents extraction to the LHC in case the specifications are not met. This avoids losses, unnecessary stress of machine protection components and luminosity degradation, additionally helping efficiency during the filling process. The system has been operational since the 2009 LHC run, checking the beam pattern, its correct position with respect to the LHC references, individual bunch lengths and stability. In this paper the algorithms used, the hardware implementation and the operational aspects are presented.

Expression, purification and preliminary crystallographic analysis of sucrose phosphate synthase (SPS) from Halothermothrix orenii

International Nuclear Information System (INIS)

Huynh, Frederick; Tan, Tien-Chye; Swaminathan, Kunchithapadam; Patel, Bharat K. C.

2004-01-01

The first crystallographic study of a sucrose phosphate synthase from H. orenii, an organism that is both thermophilic and halophilic, is reported. The protein crystal diffracts X-rays to 3.01 Å. This is the first report of the crystallization of a sucrose phosphate synthase (SPS; EC 2.4.1.14). It also constitutes the first study of a sucrose phosphate synthase from a non-photosynthetic thermohalophilic anaerobic bacterium, Halothermothrix orenii. The purified recombinant spsA protein has been crystallized in the monoclinic space group C2, with unit-cell parameters a = 154.2, b = 47.9, c = 72.3 Å, β = 103.16°, using the hanging-drop vapour-diffusion method. The crystal diffracts X-rays to a resolution limit of 3.01 Å. Heavy-metal and halide-soaking trials are currently in progress to solve the structure

Multiplicity fluctuations of pions and protons at SPS energy – An in ...

Indian Academy of Sciences (India)

but none of them can explain all the datasets simultaneously. ... in a collision, a new parameter named as 'compound multiplicity' (nc = ng + ns ... sion plates by 32S beam with 200 A GeV incident energy at CERN SPS. ... (b) Grey particles: They are mainly fast target recoil protons with energy up to ..... occurs reverse result.

A GIF++ Gamma Irradiation Facility at the SPS H4 Beam Line

CERN Document Server

Capéans-Garrido, M; Linssen, L; Moll, M; Rembser, C

2009-01-01

The current document describes a proposal to implement a new gamma irradiation facility, combined with a high-energy particle beam in the SPS H4 beam line in hall EHN1. This new GIF++ facility is motivated by strong needs from the LHC and sLHC detector and accelerator communities for the tests of LHC components and systems.

SPS RF System Amplifier plant

CERN Multimedia

1977-01-01

The picture shows a 2 MW, 200 MHz amplifier plant with feeder lines. The main RF-system of the SPS comprises four cavities: two of 20 m length and two of 16.5 m length. They are all installed in one long straight section (LSS 3). These cavities are of the travelling-wave type operating at a centre frequency of 200.2 MHz. They are wideband, filling time about 700 ns and untuned. The power amplifiers, using tetrodes are installed in a surface building 200 m from the cavities. Initially only two cavities were installed, a third cavity was installed in 1978 and a forth one in 1979. The number of power amplifiers was also increased: to the first 2 MW plant a second 2 MW plant was added and by end 1979 there were 8 500 kW units combined in pairs to feed each of the 4 cavities with up to about 1 MW RF power, resulting in a total accelerating voltage of about 8 MV. See also 7412016X, 7412017X, 7411048X.

The role of veterinary epidemiology and veterinary services in complying with the World Trade Organization SPS agreement.

Science.gov (United States)

Zepeda, C; Salman, M; Thiermann, A; Kellar, J; Rojas, H; Willeberg, P

2005-02-01

The agreement on the application of sanitary and phytosanitary measures (SPS agreement) was one of the major products of the GATT's Uruguay round of multilateral trade negotiations, signed in Marrakesh on 15 April 1994. This agreement and others are part of the treaty that established the World Trade Organization (WTO). The WTO superseded the GATT as the umbrella organization for international trade (WTO, 1998a). The SPS agreement's main intent is to provide guidelines and provisions to member countries to facilitate trade while taking measures to protect human, animal or plant life or health. The agreement dictates that all sanitary measures must be scientifically based and not more restrictive than required to avoid the risk identified. The agreement recommends the use of international standards from the World Organization for Animal Health (OIE), Codex Alimentarius (CAC) and the International Plant Protection Convention (IPPC) as the basis for import requirements. If a country chooses to apply more restrictive measures than those in the international standards, it has to justify its position through a risk analysis, thus avoiding the use of sanitary and phytosanitary measures as unjustified barriers to trade. More than ever, veterinary services worldwide are faced with having to fulfill a crucial role in protecting their country's animal health status, provide sound surveillance information on the occurrence of diseases within their territories, and conduct scientifically valid risk analyses to establish justified import requirements. During the past two decades, most countries have experienced resource reduction in their veterinary services. The effect of these policies has been severe, in many cases leading to an inability of veterinary services to conduct their disease prevention and control duties. There is a clear inconsistency between the demands placed on veterinary services and the current level of funding and support they are receiving, particularly in

Neutral strange particle production at top SPS energy measured by the CERES experiment

International Nuclear Information System (INIS)

Radomski, S.

2006-01-01

Systematics of strange particle production in collisions of ultrarelativistic nuclei provides an insight into the properties of the strongly interacting matter. Hadrochemistry, the study of the relative yields, provides information about chemical freeze-out and the position of the system in the phase diagram. Strangeness production at Super Proton Synchrotron (SPS) energies is not fully explained by the thermal model of hadron gas. Data reported by one experiment show sharp structures as a function of energy which are interpreted as a signature for a phase transition, but due to discrepancies in the results between two different experiments, a conclusion can not be drawn. This thesis is part of an effort to build a database of the strangeness production at SPS energy. The particular subject of this work is a precise measurement of the production of K S 0 . The results are compared with two other experiments and the prediction of the thermal model. The high precision data shed light on the systematics of strangeness production and allow clarification of the experimental status. The study of transverse momentum spectra provides information about the temperature and the radial expansion of the system. Here, as in the case of particle yields, interesting structures are visible as a function of energy. A rapid increase in the number of degrees of freedom is visible in the SPS region. A large part of the strangeness is carried by the neutral strange baryon Λ. Here the experimental situation is even more complicated because the reconstruction of the Λ yield requires large extrapolation to low transverse momentum. In this work first results on Λ production will be presented. (orig.)

Neutral strange particle production at top SPS energy measured by the CERES experiment

Energy Technology Data Exchange (ETDEWEB)

Radomski, S.

2006-07-05

Systematics of strange particle production in collisions of ultrarelativistic nuclei provides an insight into the properties of the strongly interacting matter. Hadrochemistry, the study of the relative yields, provides information about chemical freeze-out and the position of the system in the phase diagram. Strangeness production at Super Proton Synchrotron (SPS) energies is not fully explained by the thermal model of hadron gas. Data reported by one experiment show sharp structures as a function of energy which are interpreted as a signature for a phase transition, but due to discrepancies in the results between two different experiments, a conclusion can not be drawn. This thesis is part of an effort to build a database of the strangeness production at SPS energy. The particular subject of this work is a precise measurement of the production of K{sub S}{sup 0}. The results are compared with two other experiments and the prediction of the thermal model. The high precision data shed light on the systematics of strangeness production and allow clarification of the experimental status. The study of transverse momentum spectra provides information about the temperature and the radial expansion of the system. Here, as in the case of particle yields, interesting structures are visible as a function of energy. A rapid increase in the number of degrees of freedom is visible in the SPS region. A large part of the strangeness is carried by the neutral strange baryon {lambda}. Here the experimental situation is even more complicated because the reconstruction of the {lambda} yield requires large extrapolation to low transverse momentum. In this work first results on {lambda} production will be presented. (orig.)

Design and installation of the MSE septum system in the new LSS4 extraction channel of the SPS

CERN Document Server

Balhan, B; Guinand, R; Luiz, F; Rizzo, A; Weterings, W; CERN. Geneva. AB Department

2003-01-01

For the extraction of the beam from the Super Proton Synchrotron (SPS) to ring 2 of the Large Hadron Collider (LHC) and the CERN Neutrino to Gran Sasso (CNGS) facility, a new fast-extraction system has been installed in the long straight section LSS4 of the SPS. Besides extraction bumpers, enlarged aperture quadrupoles and extraction kicker magnets (MKE), six conventional DC septum magnets (MSE) are used. These magnets are mounted on a single mobile retractable support girder, which is motorised in order to optimise the local SPS aperture during setting up. The MSE septa are connected by a so-called plug-in system to a rigid water-cooled bus bar, which itself is powered by water-cooled cables. In order to avoid destruction of the septum magnet coils by direct impact of the extracted beam, a dilution element (TPSG) has been placed immediately upstream of the first septum coil. The whole system is kept at the required vacuum pressure by ion pumps attached to separate modules (MP). In this note we present the de...

Onset of deconfinement and search for the critical point of strongly interacting matter at CERN SPS energies

CERN Document Server

Rybczyński, Maciej

2014-01-01

The exploration of the QCD phase diagram particularly the search for a phase transition from hadronic to partonic degrees of freedom and possibly a critical endpoint, is one of the most challenging tasks in present heavy-ion physics. As observed by the NA49 experiment, several hadronic observables in central Pb+Pb collisions at the CERN SPS show qualitative changes in their energy dependence. These features are not observed in elementary interactions and indi- cate the onset of a phase transition in the SPS energy range. The existence of a critical point is expected to result in the increase of event-by-event fluctuations of various hadronic observables provided that the freeze-out of the measured hadrons occurs close to its location in the phase di- agram and the evolution of the final hadron phase does not erase the fluctuations signals. Further information about the existence and nature of a phase transition in the SPS energy range can be gained from the studies of event-by-event fluctuations of final stat...

Interface evolution and shear strength of Al/Ti bi-metals processed by a spark plasma sintering (SPS) apparatus

Energy Technology Data Exchange (ETDEWEB)

Miriyev, Aslan, E-mail: aslan.miriyev@columbia.edu [Department of Mechanical Engineering, Columbia University in the City of New York, 500 W. 120th St., Mudd 220, New York, NY 10027 (United States); Levy, Asaf; Kalabukhov, Sergey; Frage, Nachum [Department of Materials Engineering, Ben-Gurion University of the Negev, P.O.B. 653, Beer Sheva 8410501 (Israel)

2016-09-05

Microstructural evolution of the Al/Ti bi-metal interface during heat treatment in a spark plasma sintering (SPS) apparatus was investigated under various conditions for the first time. A mechanism of interfacial layer growth was suggested based on the results of SEM, TEM and X-ray diffraction analysis. A continuous TiAl{sub 3} intermetallic layer was formed at the Al/Ti interface even after a processing time as short as about a minute. The TiAl{sub 3} layer grew mainly into the Ti part, while only a few individual grains grew into the Al part. Evolution of the interlayer was determined by Al diffusion through the (TiAl{sub 3}/TiAl{sub 3}) grain boundary. The activation energy of the process was 140 kJ/mol. The shear strength of the interface in the Al/Ti bi-metal was determined after various heat treatments. The shear strength of the bi-metal was limited by the properties of aluminum, with no effect of interlayer thickness or current mode and pulse pattern of the SPS treatment being detected. - Highlights: • Spark plasma sintering apparatus was used for heat treatment of Al/Ti bi-metals. • Microstructural evolution of Al/Ti interface during SPS treatment was investigated. • A continuous TiAl{sub 3} intermetallic layer was formed at the Al/Ti interface. • The bi-metal shear strength was limited by the properties of pure aluminum. • No effect of TiAl{sub 3} thickness or SPS current mode and pulse pattern was detected.

Angelo State SPS Marsh White Award: Physics After School Special (P.A.S.S.)

Science.gov (United States)

Desai, Vikesh; Sauncy, Toni

2012-03-01

With a recent Marsh White Award from the SPS National Office, the Angelo State SPS has teamed up with a local YMCA after school program to provide fun lab experiences for the diverse group of K-3^rd graders. Several undergraduate presenters are involved, and the funding was used to purchase tshirts for all participants. The afterschool group of approximately 30 children has visited the campus for the first lab session and plans three additional hands on lab experiences over the course of the semester. For the final visit, the Peer Pressure Team will conduct a full demonstration show and P.A.S.S. Party. The goal of this public engagement is to motivate these young students to learn more about physics with hands on activities in a fun and safe environment and to establish meaningful mentoring relationships between undergraduate physics majors and younger students.

An FPGA Based Multiprocessing CPU for Beam Synchronous Timing in CERN's SPS and LHC

CERN Document Server

Ballester, F J; Gras, J J; Lewis, J; Savioz, J J; Serrano, J

2003-01-01

The Beam Synchronous Timing system (BST) will be used around the LHC and its injector, the SPS, to broadcast timing meassages and synchronize actions with the beam in different receivers. To achieve beam synchronization, the BST Master card encodes messages using the bunch clock, with a nominal value of 40.079 MHz for the LHC. These messages are produced by a set of tasks every revolution period, which is every 89 us for the LHC and every 23 us for the SPS, therefore imposing a hard real-time constraint on the system. To achieve determinism, the BST Master uses a dedicated CPU inside its main Field Programmable Gate Array (FPGA) featuring zero-delay hardware task switching and a reduced instruction set. This paper describes the BST Master card, stressing the main FPGA design, as well as the associated software, including the LynxOS driver and the tailor-made assembler.

An evaluation of UO2-CNT composites made by SPS as an accident tolerant nuclear fuel pellet and the feasibility of SPS as an economical fabrication process for the nuclear fuel cycle

Science.gov (United States)

Cartas, Andrew R.

The innovative and advanced purpose of this study is to understand and establish proper sintering procedures for Spark Plasma Sintering process in order to fabricate high density, high thermal conductivity UO2 -CNT pellets. Mixing quality and chemical reactions have been investigated by field emission scanning electron microscopy (FESEM), wavelength dispersive spectroscopy (WDS), and X-ray diffraction (XRD). The effect of various types of CNTs on the mixing and sintering quality of UO2-CNT pellets with SPS processing have been examined. The Archimedes Immersion Method, laser flash method, and FE-SEM will be used to investigate the density, thermal conductivity, grain size, pinning effects, and CNT dispersion of fabricated UO2-CNT pellets. Pre-fabricated CNT's were added to UO 2 powder and dispersed via sonication and/or ball milling and then made into composite nuclear pellets. An investigation of the economic impact of SPS on the nuclear fuel cycle for producing pure and composite UO2 fuels was conducted.

Transverse studies with ions at SPS flat bottom

CERN Document Server

Antoniou, F; Saa Hernandez, A; Huschauer, A

2017-01-01

The LHC injectors upgrade project (LIU) aims at con-solidating and upgrading the existing accelerator chain atCERN in view of the increased beam performance requiredfor the High Luminosity LHC (HL-LHC) project. For theion chain, the losses and emittance growth in the SPS imposepresently the main performance limitation. The significantbeam degradation encountered on the long injection plateauhas been studied during the 2016 MD runs with Pb82+. Inthis report we present the systematic measurements of emit-tance, bunch length and transmission performed along theinjection plateau for different bunch intensities. We present,as well, static and dynamic tune scans for the optimizationof the working point and measurement of the loss rate atcloseby resonances.

Energy and system size dependence of {xi}{sup -} and anti {xi}{sup +} production in relativistic heavy-ion collisions at the CERN SPS

Energy Technology Data Exchange (ETDEWEB)

Mitrovski, M.K.

2007-11-21

The strong nuclear force is described by Quantum Chromodynamics (QCD), the parallel field theory to Quantum Electrodynamics (QED) that describes the electromagnetic force. It is propagated by gluons analogously to photons in the electromagnetic force, but unlike photons, which do not carry electric charge, gluons carry color, and they can self-interact. However, as individual quarks have never been observed in nature, it is postulated that the color charge itself is confined, and hence all baryons and mesons must be colorless objects. To study nuclear matter under extreme conditions, it is necessary to create hot and dense nuclear matter in the laboratory. In such conditions the confinement between quarks and gluons is cancelled (deconfinement). This state is characterized with a quasi-free behavior of quarks and gluons. The strange (s) and anti-strange (anti-s) quarks are not contained in the colliding nuclei, but are newly produced and show up in the strange hadrons in the final state. It was suggested that strange particle production is enhanced in the QGP with respect to that in a hadron gas. This enhancement is relative to a collision where a transition to a QGP phase does not take place, such as p+p collisions where the system size is very small. Therefore the energy- and system size dependence is studied to receive a picture about the initial state. In this thesis experimental results on the energy- and system size dependence of Xi hyperon production at the CERN SPS is shown. All measurements were performed with the NA49 detector at the CERN SPS. NA49 took central lead-lead collisions from 20 - 158 AGeV, minimus bias lead-lead collisions at 40 and 158 AGeV, and semi-central silicon-silicon collisions at 158 AGeV. The NA49 experiment features a large acceptance in the forward hemisphere allowing for measurements of Xi rapidity spectra. At the SPS accelerator at CERN Pb+Pb collisions are performed with beam energies to 158 AGeV. The analyzed data sets were

Was a new phase of nuclear matter observed at CERN SPS...?

International Nuclear Information System (INIS)

Odyniec, G.

2001-01-01

The enhanced production of strange particles, that was predicted as a consequence of the formation of quark-gluon plasma, was observed in CERN SPS heavy ion experiments. As data matured, the emphasis on theory and interpretation of experimental results has increased. In this presentation the hadronic yields and their ratios, as well as the role of strangeness production in the search for a new phase of matter, in both experiment and theory, are discussed. (author)

ACANTHAMOEBA SP.S-11 PHAGOCYTOTIC ACTIVITY ON MYCOBACTERIUM LEPRAE IN DIFFERENT NUTRIENT CONDITIONS.

Science.gov (United States)

Paling, Sepling; Wahyuni, Ratna; Ni'matuzahroh; Winarni, Dwi; Iswahyudi; Astari, Linda; Adriaty, Dinar; Agusni, Indropo; Izumi, Shinzo

2018-01-01

Mycobacterium leprae ( M. leprae ) is a pathogenic bacterium that causes leprosy. The presence of M. leprae in the environment is supported by microorganisms that act as the new host for M. leprae . Acanthamoeba 's potential to be a host of M. leprae in the environment. Acanthamoeba sp. is Free Living Amoeba (FLA) that classified as holozoic, saprophytic, and saprozoic. The existence of nutrients in the environment influence Acanthamoeba ability to phagocytosis or pinocytosis. This study is aimed to determine Acanthamoeba sp.S-11 phagocytic activity to Mycobacterium leprae ( M. leprae ) which cultured in non-nutrient media and riched-nutrient media. This research conducted by culturing Acanthamoeba sp.S-11 and M. leprae on different nutrient media conditions. M. leprae intracellular DNA were isolated and amplified by M. leprae specific primers through Real Time PCR (Q-PCR). The results showed that Acanthamoeba co-cultured on non-nutrient media were more active to phagocyte M. leprae than on rich-nutrient media. The use of non-nutrient media is recommended to optimize Acanthamoeba sp. phagocytic activity to M. leprae .

Effect of the Various Impedances on Longitudinal Beam Stability in the CERN SPS

CERN Document Server

Lasheen, Alexandre; Repond, Joël; Shaposhnikova, Elena

2016-01-01

The High Luminosity (HL)-LHC project at CERN aims at a luminosity increase by a factor ten and one of the necessary ingredients is doubling the bunch intensity to 2.4x10¹¹ ppb for beams with 25 ns bunch spacing. Many improvements are already foreseen in the frame of the LHC Injector Upgrade (LIU) project, but probably this intensity would still not be reachable in the SPS due to longitudinal instabilities. Recently a lot of effort went into finding the impedance sources of the instabilities. Particle simulations based on the latest SPS impedance model are now able to reproduce the measured instability thresholds and were used to determine the most critical impedance sources by removing them one by one from the model. It was found that impedance of vacuum flanges and of the already damped 630 MHz HOM of the main RF system gave for 72 bunches the comparable intensity thresholds. Possible intensity gains are defined for realistic impedance modifications and for various beam configurations (number of bunches, l...

A Novel Eddy Current Septum Magnet for SPS Extraction towards LHC and CNGS

CERN Document Server

Schröder, G H; Carlier, E; Dieperink, J H; Ducimetière, L; Goddard, B; Lázár, C; Mayer, M; Vossenberg, Eugène B; Weterings, W

2000-01-01

A new East Fast-Extraction System is under construction in the SPS, to supply particles with a maximum batch length of 7.8 us and 10.5 us to the LHC and to CNGS (CERN Neutrino to Gran Sasso), respectively. The extraction septum magnets actually used at the SPS have been designed for slow extraction over several seconds, have large cooling and electrical power demands and need frequently maintenance in a high radiation environment. A fast system of only 250 us pulse duration has therefore been developed, using a half-sine excitation pulse with a superimposed third harmonic. The short pulse duration requires very thin magnetic yoke laminations, which can not easily be stamped and stacked. Profiting from a development for the LHC beam dump kicker magnets, the yoke is therefore built-up from tape-wound cylindrical cores, employing 50 um thick Si-steel tape. Thirty two cores are stacked longitudinally to produce a yoke of 3.2 meter length. The aperture is cut radial into each cylinder. The cores are radial compres...

Candidate solar cell materials for photovoltaic conversion in a solar power satellite /SPS/

Science.gov (United States)

Glaser, P. E.; Almgren, D. W.

1978-01-01

In recognition of the obstacles to solar-generated baseload power on earth, proposals have been made to locate solar power satellites in geosynchronous earth orbit (GEO), where solar energy would be available 24 hours a day during most of the time of the year. In an SPS, the electricity produced by solar energy conversion will be fed to microwave generators forming part of a planar phase-array transmitting antenna. The antenna is designed to precisely direct a microwave beam of very low intensity to one or more receiving antennas at desired locations on earth. At the receiving antenna, the microwave energy will be safely and efficiently reconverted to electricity and then be transmitted to consumers. An SPS system will include a number of satellites in GEO. Attention is given to the photovoltaic option for solar energy conversion in GEO, solar cell requirements, the availability of materials, the implication of large production volumes, requirements for high-volume manufacture of solar cell arrays, and the effects of concentration ratio on solar cell array area.

Non-local Fast Extraction from the CERN SPS at 100 and 440 GeV

CERN Document Server

Velotti, F M; Bartmann, W; Carlier, E; Cornelis, K; Efthymiopoulos, I; Goddard, B; Jensen, L K; Kain, V; Kowalska, M; Mertens, V; Steerenberg, R

2013-01-01

The Long Straight Section 2 (LSS2) of the CERN SPS is connected with the North Area (NA), to which the beam to date has always been extracted using a resonant extraction technique. For new proposed short- and long-baseline neutrino experiments, a fast single turn extraction to this experimental area is required. As there are no kickers in LSS2, and the integration of any new kickers with the existing electrostatic septum would be problematic, a solution has been developed to fast extract the beam using non-local extraction with other SPS kickers. Two different kicker systems have been used, the injection kicker in LSS1 and the stronger extraction kicker in LSS6 to extract 100 and 440 GeV beam, respectively. For both solutions a large emittance beam was extracted after 5 or 9 full betatron periods. The concept and simulation details are presented with the analysis of the aperture and beam loss considerations and experimental results collected during a series of beam tests.

Performance Evaluation of the SPS Scraping System in View of the High Luminosity LHC

CERN Document Server

AUTHOR|(SzGeCERN)659273; Cerutti, Francesco

Injection in the LHC is a delicate moment, since the LHC collimation system cannot offer adequate protection during beam transfer. For this reason, a complex chain of injection protection devices has been put in place. Among them, the SPS scrapers are the multi-turn cleaning system installed in the SPS aimed at halo removal immediately before injection in the LHC. The upgrade in luminosity of the LHC foresees beams brighter than those currently available in machine, posing serious problems to the performance of the existing injection protection systems. In particular, the integrity of beam-intercepting devices is challenged by unprecedented beam parameters, leading to interactions potentially destructive. In this context, a new design of scrapers has been proposed, aimed at improved robustness and performance. This thesis compares the two scraping systems, i.e. the existing one and the one proposed for upgrade. Unlike any other collimation system for regular halo cleaning, both are "fast" systems, characteris...

TMCI thresholds for LHC single bunches in the CERN SPS and comparison with simulations

CERN Document Server

Bartosik, H; Papaphilippou, Y; Rumolo, G; Salvant, B; Zannini, C

2014-01-01

At the beginning of 2013 an extensive measurement campaign was carried out at the SPS in order to determine the Transverse Mode Coupling Instability thresholds of LHC-type bunches in a wide range of intensities and longitudinal emittances. The measurements were performed in two different configurations of machine optics (nominal and low gamma transition) with the goal to characterize the differences in behavior and performance. The purpose of this paper is to describe in detail the measurement procedure and results, as well as the comparison of the experimental data with HEADTAIL simulations based on the latest SPS impedance model. Beside the impedances of the resistive wall, the beam position monitors (BPMs), the RF cavities, and the flanges, an advanced model of the impedance of the kicker magnets is included, which are found to play a major role in the definition of the stability region of the LHC-type bunches in the two optics configurations studied.

Hyperon production at the CERN SPS:results from the NA57 experiment

Czech Academy of Sciences Publication Activity Database

Antinori, F.; Bacon, P. A.; Badala, A.; Staroba, Pavel; Závada, Petr

2004-01-01

Roč. 30, - (2004), S129-S138 ISSN 0954-3899 Institutional research plan: CEZ:AV0Z1010920 Keywords : ultra-relativistic heavy-ion beams * CERN SPS * hadronic matter * energy density * colour deconfined state of matter * Pb-Pb collisions at 160 A GeV/c * mid-rapidity * strangeness enhancment Subject RIV: BF - Elementary Particles and High Energy Physics Impact factor: 1.533, year: 2004

The PS Booster, PS and SPS Magnets for the next 25 years

CERN Document Server

Tommasini, D

2010-01-01

This note provides information and analysis on the present status of the magnets installed in the CERN Proton Synchrotron Booster (PSB), the Proton Synchrotron (PS) and the Super Proton Synchrotron (SPS) in view of their possible operation for the next 25 years. The note does not cover the magnets installed in the transfer lines, neither it covers the fast injection/extraction magnets (septa and kickers).

Study of infrastructure considerations for microwave energy ground receiving stations. Satellite Power System (SPS) offshore rectenna siting study in western Europe. An executive summary. Final report

Energy Technology Data Exchange (ETDEWEB)

Bresters, A.R.

1980-11-01

The feasibility of offshore rectenna sites in the North Sea based on a reference SPS concept of 5 GW was investigated. Site criteria include a 20 km wide safety zone between the site and the shore, a 300 km limit to centers of power consumption, and a water depth of 30 m. Artificial islands, polders, atolls and exposed gravity or jacket structures were considered. Only the island and polder concept permit antenna installation without modifications to the reference design. The polder concept was selected, costing half that of the artificial island (160 km sq). Construction material requirements are given for the dikes. Total construction time is 8.5 years. Costs range between 4.7 and 5.4 billion in 1980 dollars, or $0.02 per kw hr over 30 years. (ESA)

SPS/LEP beam transfer equipment control using industrial automation components

International Nuclear Information System (INIS)

Aimar, A.; Berard, G.; Bretin, J.L.; Carlier, E.; Dieperink, J.H.; Laffin, M.; Mertens, V.; Verhagen, H.

1992-01-01

Several control systems for SPS and LEP beam transfer equipment have to be commissioned in the near future. Tools for fast software development, easy maintenance and modifications, compliance with industrial standards, and independence of specific suppliers are considered to be essential. A large fraction of the systems can be realized using off-the-shelf industrial automation components like industrial I/O systems, programmable logic controllers, or diskless PCs. Specific electronics built up in G-64 can be integrated. Diskless systems running UNIX and X Windows are foreseen as process controllers and local access media. (author)

Implementation of Carbon Thin Film Coatings in the Super Proton Synchrotron (SPS) for Electron Cloud Mitigation

CERN Document Server

Costa Pinto, P; Basso, T; Edwards, P; Mensi, M; Sublet, A; Taborelli, M

2014-01-01

Low Secondary Electron Yield (SEY) carbon thin films eradicate electron multipacting in accelerator beam pipes. Two magnetic cells of the SPS were coated with such material and installed. In total more than forty vacuum vessels and magnet interconnections were treated. The feasibility of the coating process was validated. The performance of the carbon thin film will be tested with LHC nominal beams after the end of the long shutdown 1. Particular attention will be drawn to the long term behaviour. This paper presents the sputtering techniques used to coat the different components; their characterization (SEY measurements on coupons, RF multipacting tests and pump down curves); and the technology to etch the carbon film in case of a faulty coating. The strategy to coat the entire SPS will also be described.

Travelling Wave Structure of an SPS RF Cavity

CERN Multimedia

CERN PhotoLab

1974-01-01

The RF cavities for acceleration of particles in the SPS have a travelling-wave structure. They operate at a fixed frequency of 200 MHz (h = 4620). With a quality factor of Q = 100, the bandwidth covers the small frequency swing for the acceleration of protons from as low as 10 GeV to the top energy of 450 GeV. Later on, for the acceleration of ions, with a larger frequency swing, turn-to-turn phase jumps did the trick. Two cavities, each consisting of 5 tank sections, were installed in long straight section 3. Each cavity is driven by a power amplifier of 750 kW CW (1 MW pulsed). Another 2 cavities were added later on. See also 7411033 and 7802190.

Experience with the control system for the SPS

International Nuclear Information System (INIS)

Crowley-Milling, M.C.

1978-01-01

The design of the multicomputer control system for the 400 GeV Super Proton Synchrotron (SPS) at CERN was described in the report CERN 75-20, issued in 1975, before the commissioning of the accelerator. The present report, which should be read in conjunction with the earlier one, describes the modification made to the system in the light of experience, and how it has adapted to changing requirements. Reliability of the system and how it has adapted to changing requirements. Reliability of the system and of its components is discussed. Taking into account modern developments of microprocessors, etc., the changes that might be made if the system were to be redesigned are examined. Finally, the application of the design philosophy to other fields is discussed briefly. (Auth.)

Stopping, heating, thermalization and expansion at SPS energies

CERN Document Server

Gaardhoje, J J

1997-01-01

The Pb beam at 158AGeV from the CERN SPS accelerator which was taken into use in the fall of 1994 has opened a new dimension in the study of highly excited nuclear matter in heavy ion reactions. It has now become possible to form reasonably large volumes (containing more than 300 nucleons) in central collisions between heavy ions, with energy and matter densities in some parts of the volume exceeding those expected for the phase transition from hadronic matter to deconfined quark and gluon matter. In this talk we discuss some features of the expansion of the hot and compressed system that may be learned by analysing the single particle spectra of baryons and mesons with emphasis on data from the NA44 experiment.

Beam Quality Preservation in the CERN PS-SPS Complex

CERN Multimedia

Arduini, Gianluigi

2004-01-01

The LHC will require beams of unprecedented transverse and longitudinal brightness. Their production imposes tight constraints on the emittance growth in each element of the LHC injector chain, namely the PS-SPS Accelerator Complex. The problems encountered at the different stages of the acceleration in the complex span a wide range of topics, such as injection matching, RF gymnastics, space charge, transverse and longitudinal single- and coupled-bunch instabilities, and electron cloud effects. The measurement techniques developed and applied to identify and study the various sources of emittance dilution to the high precision required for the LHC beams and the solutions found to control such phenomena are illustrated.

Beam Transfer Line Design for a Plasma Wakefield Acceleration Experiment (AWAKE) at the CERN SPS

CERN Document Server

Bracco, C; Brethoux, D; Clerc, V; Goddard, B; Gschwendtner, E; Jensen, L K; Kosmicki, A; Le Godec, G; Meddahi, M; Muggli, P; Mutin, C; Osborne, O; Papastergiou, K; Pardons, A; Velotti, F M; Vincke, H

2013-01-01

The world’s first proton driven plasma wakefield acceleration experiment (AWAKE) is presently being studied at CERN. The experimentwill use a high energy proton beam extracted from the SPS as driver. Two possible locations for installing the AWAKE facility were considered: the West Area and the CNGS beam line. The previous transfer line from the SPS to the West Area was completely dismantled in 2005 and would need to be fully re-designed and re-built. For this option, geometric constraints for radiation protection reasons would limit the maximum proton beam energy to 300 GeV. The existing CNGS line could be used by applying only minor changes to the lattice for the final focusing and the interface between the proton beam and the laser, required for plasma ionisation and bunch-modulation seeding. The beam line design studies performed for the two options are presented.

CERN : Nouveaux records lors d'une période d'exploitation au PS/SPS ; Un nouveau rôle pour les ISR ; Deuxième région d'intersection pour le système pp du SPS ; Détermination de la durée de vie du charme ; Calcul en Sicile et au CERN

CERN Multimedia

1979-01-01

CERN : Nouveaux records lors d'une période d'exploitation au PS/SPS ; Un nouveau rôle pour les ISR ; Deuxième région d'intersection pour le système pp du SPS ; Détermination de la durée de vie du charme ; Calcul en Sicile et au CERN

Photon production in relativistic nuclear collisions at SPS and RHIC energies

CERN Document Server

Turbide, S; Rapp, R; 10.1142/S0217751X0402258X

2004-01-01

Chiral Lagrangians are used to compute the production rate of photons from the hadronic phase of relativistic nuclear collisions. Special attention is paid to the role of the a/sub 1/ pseudovector. Calculations that include strange meson reactions, form factors, the use of consistent vector spectral densities, the emission from a quark-gluon plasma, and primordial nucleon-nucleon collisions reproduce the photon spectra measured at the Super Proton Synchrotron (SPS). Some predictions for the Relativistic Heavy Ion Collider (RHIC) are made.

Physics at the AD/PS/SPS - PLEASE NOTE CHANGE OF ROOM!(2/4)

CERN Multimedia

CERN. Geneva

2012-01-01

Lecture 2: QCD and hadron physics: COMPASS, NA61, DIRAC The lecture will discuss the research done at the COMPASS, SHINE and DIRAC experiments at the SPS and PS. COMPASS studies nucleon structure and hadron spectroscopy, SHINE searches for the critical point and onset of deconfinement in heavy ion collisions while DIRAC studies the pi-pi scattering length in pionic atoms.

Coldbox installation for HL-LHC crab cavity test in the SPS tunnel (BA6)

CERN Document Server

Ordan, Julien Marius

2018-01-01

The Cold-box, produced by Linde Kryotechnik for the SPS crab-cavity test stand for HL-LHC, on its arrival at CERN. It wll be transported into the tunnel in horizontal position and then will have to be tilted in its operational position, on its vertical axis, before connecting it to cryogenics lines.

The CERN LEP-SPS Librarian system

International Nuclear Information System (INIS)

Corniaux, C.; Morpurgo, G.

1990-01-01

The complexity of a software working environment, such as the control system for the SPS and LEP accelerators, requires a considerable management effort. The software needed to run the machines is continuously evolving, as new releases of application and system programs are introduced rather frequency. Ideally the management effort must coordinate all the different software developers and their users (the machine operating team). A software tool, the Librarian, has been written to help them in performing this task. Its ultimate goal is to enable the accelerator operators to retain control of all the software running in the control system. All the source files needed to produce a piece of running software (a 'product') are saved together, and can be retrieved either individually or as a whole. Management of the different versions of a product is also implemented, as well as a scheme for protections and access rights depending on the type of user (Librarian manager, application manager or software developer). The data base ORACLE has been used to maintain logical links between files saved under the Librarian. (orig.)

Satellite power system (SPS). Rectenna siting: availability and distribution of nominally eligible sites

Energy Technology Data Exchange (ETDEWEB)

1980-11-01

Siting of 60 ground receiving stations (rectennas) for the SPS may pose a problem due to the large area per rectenna (15,000 hectares, 38,000 acres) and numerous siting constraints. This study analyzes areas potentially eligible for rectenna sites by mapping, at a national scale, those conditions which would preclude rectenna construction. These exclusion variables which reflect restricted lands, topography, safety, national policy and electromagnetic (microwave) effects, have been computer encoded and tabulated. Subsequent analysis of the nine electric power planning regions that make up the contiguous states indicate an apparently adequate number of nominally eligible sites in all regions in comparison to projected electrical generation. Eligibility in this context means only that areas were not excluded in this national level analysis; more detailed investigation may reveal purely local constraints or smaller scale exclusions. A second major qualification relates to small isolated eligible areas. Eliminating individual eligible clusters with less than nine times the area of one rectenna eliminates much of the Eastern US; a four-to-one adjacent eligible area test poses no such problem. An independant study of the placement of 60 nominal sites in relation to projected load centers reveals that, even with modest transmission distances, the supply of eligible areas is not a key constraint, except perhaps in the Mid-Atlantic (Electric Reliability) Council Region. Even when several less critical (potential) exclusions are considered, more than 19% of the US is eligible; every region except Mid-Atlantic has at least 50 times an many eligible sites as are required.

Pb-ions in harmonic number 4653 at SPS flat bottom

CERN Document Server

Bartosik, H; Huschauer, A

2017-01-01

Pb-ion beams suer from strong beam degradation suchas transverse emittance growth and losses on the long flatbottom of the SPS cycles used for LHC filling. A possiblecontribution to the losses could come from RF noise, espe-cially due to the frequency and amplitude modulation duringeach revolution period of the fixed frequency accelerationmode required for the acceleration of these beams. A ma-chine development session in 2016 was devoted to a directcomparison of a cycle with fixed harmonic number at flatbottom and a cycle with the usually used fixed frequencymode. The main results are reported here.

A 40 MHz Bunch by Bunch Intensity Measurement for the CERN SPS and LHC

CERN Document Server

Jakob, H; Jones, R; Jensen, L

2003-01-01

A new acquisition system has been developed to allow the measurement of the individual intensity of each bunch in a 40MHz bunch train. Such a system will be used for the measurement of LHC type beams after extraction from the CERN-PS right through to the dump lines of the CERN-LHC. The method is based on integrating the analogue signal supplied by a Fast Beam Current Transformer at a frequency of 40MHz. This has been made possible with the use of a fast integration ASIC developed by the University of Clermont-Ferrand, France, for the LHC-b pre-shower detector. The output of the integrator is digitised using a 12-bit ADC and fed into a Digital Acquisition Board (DAB) that was originally developed by TRIUMF, Canada, for use in the LHC orbit system. A full system set-up was commissioned during 2002 in the CERN-SPS, and following its success will now be extended in 2003 to cover the PS to SPS transfer lines and the new TT40 LHC extraction channel.

Experimental results concerning global observables from the CERN SPS heavy ion program

International Nuclear Information System (INIS)

Young, G.R.

1990-06-01

A brief overview is given of experimental results obtained during the initial operation of the heavy-ion program at the CERN SPS during the period 1986--1988. This paper confines itself to a presentation of results on so-called global observables, such as energy flow and multiplicity distributions, and on information extracted from them. Of particular interest among the latter are an estimate of the magnitude and spatial distribution of the energy density attained. 3 refs., 27 figs

SPS Dipole Multipactor Test and TEWave Diagnostics

CERN Document Server

Caspers, F; Edwards, P; Federmann, S; Holz, M; Taborelli, M

2013-01-01

Electron cloud accumulation in particle accelerators can be mitigated by coating the vacuum beam pipe with thin films of low secondary electron yield (SEY) material. The SEY of small coated samples are usually measured in the laboratory. To further test the properties of different coating materials, RF-induced multipacting in a coaxial waveguide configuration can be performed. The technique is applied to two main bending dipoles of the SPS, where the RF power is fed through a tungsten wire stretched along the vacuum chamber (6.4 m). A dipole with a bare stainless steel chamber shows a clear power threshold initiating an abrupt rise in reflected power and pressure. The effect is enhanced at RF frequencies corresponding to electron cyclotron resonances for given magnetic fields. Preliminary results show that the dipole with a carbon coated vacuum chamber does not exhibit any pressure rise or reflected RF power up to the maximum available input power. In the case of a large scale coating production this techniqu...

Fragmentation of Pb-Projectiles at SPS Energies

CERN Multimedia

2002-01-01

% EMU17 \\\\ \\\\ We have exposed stacks consisting of solid state nuclear track detectors (CR-39 plastic and BP-1 glass) and different target materials at the SPS to beams of Pb projectiles. Our detectors record tracks of relativistic nuclei with charge numbers of Z~$\\geq$~6 for CR-39 and Z~$\\geq$75 for BP-1. After development of the tracks by etching they are detected and measured using completely automated microscope systems. Thus experiments with high statistics are possible. \\\\ \\\\BP-1 detectors were exposed to measure total charge changing cross sections and elemental production cross sections for heavy projectile fragments. These experiments were performed for different targets CH$ _{2} $, C, Al, Cu, Ag and Pb. Comparison of the results for different targets allows to investigate contributions to charge changing reactions by electromagnetic dissociation. Multifragmentation events in which several intermediate mass fragments are emitted from the heavy Pb projectile are studied using stacks containing CR-39 d...

The new generation of PowerPC VMEbus front end computers for the CERN SPS and LEP accelerators system

CERN Document Server

Charrue, P; Ghinet, F; Ribeiro, P

1995-01-01

The CERN SPS and LEP PowerPC project is aimed at introducing a new generation of PowerPC VMEbus processor modules running the LynxOS real-time operating system. This new generation of front end computers using the state-of-the-art microprocessor technology will first replace the obsolete XENIX PC based systems (about 140 installations) successfully used since 1988 to control the LEP accelerator. The major issues addressed in the scope of this large scale project are the technical specification for the new PowerPC technology, the re-engineering aspects, the interfaces with other CERN wide projects, and the set up of a development environment. This project offers also support for other major SPS and LEP projects interested in the PowerPC microprocessor technology.

High-Pressure Spark Plasma Sintering (HP SPS): A Promising and Reliable Method for Preparing Ti-Al-Si Alloys.

Science.gov (United States)

Knaislová, Anna; Novák, Pavel; Cygan, Sławomir; Jaworska, Lucyna; Cabibbo, Marcello

2017-04-27

Ti-Al-Si alloys are prospective material for high-temperature applications. Due to low density, good mechanical properties, and oxidation resistance, these intermetallic alloys can be used in the aerospace and automobile industries. Ti-Al-Si alloys were prepared by powder metallurgy using reactive sintering, milling, and spark plasma sintering. One of the novel SPS techniques is high-pressure spark plasma sintering (HP SPS), which was tested in this work and applied to a Ti-10Al-20Si intermetallic alloy using a pressure of 6 GPa and temperatures ranging from 1318 K (1045 °C) to 1597 K (1324 °C). The low-porosity consolidated samples consist of Ti₅Si₃ silicides in an aluminide (TiAl) matrix. The hardness varied between 720 and 892 HV 5.

Electron-cloud simulation results for the SPS and recent results for the LHC

International Nuclear Information System (INIS)

Furman, M.A.; Pivi, M.T.F.

2002-01-01

We present an update of computer simulation results for some features of the electron cloud at the Large Hadron Collider (LHC) and recent simulation results for the Super Proton Synchrotron (SPS). We focus on the sensitivity of the power deposition on the LHC beam screen to the emitted electron spectrum, which we study by means of a refined secondary electron (SE) emission model recently included in our simulation code

The effectiveness of CCDSR learning model to improve skills of creating lesson plan and worksheet science process skill (SPS) for pre-service physics teacher

Science.gov (United States)

Limatahu, I.; Suyatno; Wasis; Prahani, B. K.

2018-03-01

In the previous research, CCDSR (Condition, Construction, Development, Simulation, and Reflection) learning model has been developed to improve science process skills for pre-service physics teacher. This research is aimed to analyze the effectiveness of CCDSR learning model towards the improvement skills of creating lesson plan and worksheet of Science Process Skill (SPS) for pre-service physics teacher in academic year 2016/2017. This research used one group pre-test and post-test design on 12 pre-service physics teacher at Physics Education, University of Khairun. Data collection was conducted through test and observation. Creating lesson plan and worksheet SPS skills of pre-service physics teacher measurement were conducted through Science Process Skill Evaluation Sheet (SPSES). The data analysis technique was done by Wilcoxon t-test and n-gain. The CCDSR learning model consists of 5 phases, including (1) Condition, (2) Construction, (3) Development, (4) Simulation, and (5) Reflection. The results showed that there was a significant increase in creating lesson plan and worksheet SPS skills of pre-service physics teacher at α = 5% and n-gain average of moderate category. Thus, the CCDSR learning model is effective for improving skills of creating lesson plan and worksheet SPS for pre-service physics teacher.

Validity of Scientific Based Chemistry Android Module to Empower Science Process Skills (SPS) in Solubility Equilibrium

Science.gov (United States)

Antrakusuma, B.; Masykuri, M.; Ulfa, M.

2018-04-01

Evolution of Android technology can be applied to chemistry learning, one of the complex chemistry concept was solubility equilibrium. this concept required the science process skills (SPS). This study aims to: 1) Characteristic scientific based chemistry Android module to empowering SPS, and 2) Validity of the module based on content validity and feasibility test. This research uses a Research and Development approach (RnD). Research subjects were 135 s1tudents and three teachers at three high schools in Boyolali, Central of Java. Content validity of the module was tested by seven experts using Aiken’s V technique, and the module feasibility was tested to students and teachers in each school. Characteristics of chemistry module can be accessed using the Android device. The result of validation of the module contents got V = 0.89 (Valid), and the results of the feasibility test Obtained 81.63% (by the student) and 73.98% (by the teacher) indicates this module got good criteria.

Indiana Wesleyan University SPS Physics Outreach to Rural Middle School and High School Students

Science.gov (United States)

Ostrander, Joshua; Rose, Heath; Burchell, Robert; Ramos, Roberto

2013-03-01

The Society of Physics Students chapter at Indiana Wesleyan University is unusual in that it has no physics major, only physics minors. Yet while just over a year old, IWU-SPS has been active in performing physics outreach to middle school and high school students, and the rural community of Grant County. Our year-old SPS chapter consists of majors from Chemistry, Nursing, Biology, Exercise Science, Computer Science, Psychology, Pastoral Studies, and Science Education, who share a common interest in physics and service to the community. IWU currently has a physics minor and is currently working to build a physics major program. Despite the intrinsic challenges, our multi-disciplinary group has been successful at using physics demonstration equipment and hands-on activities and their universal appeal to raise the interest in physics in Grant County. We report our experience, challenges, and successes with physics outreach. We describe in detail our two-pronged approach: raising the level of physics appreciation among the IWU student community and among pre-college students in a rural community of Indiana. Acknowledgements: We acknowledge the support of the Society of Physics Students through a Marsh White Outreach Award and a Blake Lilly Prize.

Nine years of carbon coating development for the SPS upgrade: achievements and heritage.

CERN Document Server

Taborelli, Mauro; Costa Pinto, Pedro; Cruikshank, Paul

2015-01-01

CERN has succeeded in producing carbon coatings that eradicate electron cloud in accelerators without any beam conditioning or in situ heating. Investing about 1 MCHF and dedicating 31 FTE (28 man-years, staff and associate members) in 9 years in the framework of LIU-SPS, CERN has increased: technological competences in thin-film coatings, worldwide visibility in surface characterisation, and capability in electron cloud measurement. Future projects are still benefiting from such an investment.

SPS beam to the West Hall

CERN Multimedia

CERN PhotoLab

1976-01-01

One of the two target stations feeding the West Hall (see Annual Report 1976). After the proton beam was split into three branches, the outer two were directed on to targets in the cast iron shielding box, the centre one passing through the box to another target station downstream. Five different targets could be put in each beam, controlled by the mechanism seen on top.

The new generation of PowerPC VMEbus front end computers for the CERN SPS and LEP accelerators control system

CERN Document Server

Van den Eynden, M

1995-01-01

The CERN SPS and LEP PowerPC project is aimed at introducing a new generation of PowerPC VMEbus processor modules running the LynxOS real-time operating system. This new generation of front end computers using the state-of-the-art microprocessor technology will first replace the obsolete Xenix PC based systems (about 140 installations) successfully used since 1988 to control the LEP accelerator. The major issues addressed in the scope of this large scale project are the technical specification for the new PowerPC technology, the re-engineering aspects, the interfaces with other CERN wide projects, and the set up of a development environment. This project offers also support for other major SPS and LEP projects interested in the PowerPC microprocessor technology.

Geotectonic variations of radon fields in Tashkent subway stations

International Nuclear Information System (INIS)

Yafasov, A.Ya.; Akimov, V.A.

2001-01-01

The anomalies of radon fields in the air of stations of Tashkent subway were investigated. These stations are located in areas with different tectonic characteristics. The influence of tectonic anomalies on formation and variations of radon fields in the environment was shown. (author)

Measurement of Electron Cloud Effects in SPS

CERN Document Server

Jiménez, J M

2004-01-01

The electron cloud is not a new phenomenon, indeed, it was observed already in other machines like the proton storage rings in BINP Novosibirsk or in the Intersecting Storage Ring (ISR) at CERN. Inside an accelerator beam pipe, the electrons can collectively and coherently interact with the beam potential and degrade the performance of the accelerators operating with intense positively charged bunched beams. In the LHC, electron multipacting is expected to take place in the cold and warm beam pipe due to the presence of the high intensities bunched beams, creating an electron cloud. The additional heat load induced by the electron cloud onto the LHC beam screens of the cold magnets of the LHC bending sections (the arcs represent ~21 km in length) was, and is still, considered as one of the main possible limitation of LHC performances. Since 1997 and in parallel with the SPS studies with LHC-type beams, measurements in other machines or in the laboratory have been made to provide the input parameters required ...

Factor solutions of the Social Phobia Scale (SPS) and the Social Interaction Anxiety Scale (SIAS) in a Swedish population.

Science.gov (United States)

Mörtberg, Ewa; Reuterskiöld, Lena; Tillfors, Maria; Furmark, Tomas; Öst, Lars-Göran

2017-06-01

Culturally validated rating scales for social anxiety disorder (SAD) are of significant importance when screening for the disorder, as well as for evaluating treatment efficacy. This study examined construct validity and additional psychometric properties of two commonly used scales, the Social Phobia Scale and the Social Interaction Anxiety Scale, in a clinical SAD population (n = 180) and in a normal population (n = 614) in Sweden. Confirmatory factor analyses of previously reported factor solutions were tested but did not reveal acceptable fit. Exploratory factor analyses (EFA) of the joint structure of the scales in the total population yielded a two-factor model (performance anxiety and social interaction anxiety), whereas EFA in the clinical sample revealed a three-factor solution, a social interaction anxiety factor and two performance anxiety factors. The SPS and SIAS showed good to excellent internal consistency, and discriminated well between patients with SAD and a normal population sample. Both scales showed good convergent validity with an established measure of SAD, whereas the discriminant validity of symptoms of social anxiety and depression could not be confirmed. The optimal cut-off score for SPS and SIAS were 18 and 22 points, respectively. It is concluded that the factor structure and the additional psychometric properties of SPS and SIAS support the use of the scales for assessment in a Swedish population.

Performances of solar water pumping station with solar tracker

International Nuclear Information System (INIS)

Buniatyan, V.V.; Vardanyan, A.A.

2011-01-01

For the solar water pumping stations ? solar tracking system with phototransistor is developed. On the basis of the experimental investigations the utility and efficiency of the PV water pumping station with solar tracker under different conditions of varying solar radiation in Armenia is shown

Thermal Studies on the SPS Wideband Transverse Feedback Kicker

CERN Document Server

Roggen, Toon; Hofle, Wolfgang; Montesinos, Eric; CERN. Geneva. ATS Department

2016-01-01

As part of the SPS wideband transverse feedback system in the framework of the LHC Injector Upgrade (LIU) project, a wideband kicker design is being proposed. Vertical beam instabilities due to intensity dependent effects (electron cloud instability (ECI) and transverse mode coupling instability (TMCI)) are potentially suppressed by using a feedback system driving such a kicker system. One of the options for a kicker is a one meter long slotted-coaxial kicker, providing a substantial vertical kick strength (10ˉ5 –10ˉ4 eV.s/m) over a bandwidth ranging from nearly DC to 1 GHz. The necessary kick strength requires a total power of 4 kW. This note describes thermal studies that assisted in the material choice of the feedthroughs of the slotted-coaxial kicker and guided the design choices.

THE EFFECT OF PROBLEM SOLVING LEARNING MODEL BASED JUST IN TIME TEACHING (JiTT ON SCIENCE PROCESS SKILLS (SPS ON STRUCTURE AND FUNCTION OF PLANT TISSUE CONCEPT

Directory of Open Access Journals (Sweden)

Resha Maulida

2017-11-01

Full Text Available The purpose of this study was to determine the effect of Problem Solving learning model based Just in Time Teaching (JiTT on students' science process skills (SPS on structure and function of plant tissue concept. This research was conducted at State Senior High School in South Tangerang .The research conducted using the quasi-experimental with Nonequivalent pretest-Postest Control Group Design. The samples of this study were 34 students for experimental group and 34 students for the control group. Data was obtained using a process skill test instrument (essai type that has been tested for its validity and reliability. Result of data analysis by ANACOVA, show that there were significant difference of postest between experiment and control group, by controlling the pretest score (F = 4.958; p <0.05. Thus, the problem-solving learning based on JiTT proved to improve students’ SPS. The contribution of this treatment in improving the students’ SPS was 7.2%. This shows that there was effect of problem solving model based JiTT on students’ SPS on the Structure and function of plant tissue concept.

Workshop on Satellite Power Systems (SPS) effects on optical and radio astronomy

International Nuclear Information System (INIS)

Stokes, G.M.; Ekstrom, P.A.

1980-04-01

The impacts of the SPS on astronomy were concluded to be: increased sky brightness, reducing the effective aperture of terrestrial telescopes; microwave leakage radiation causing erroneous radioastronomical signals; direct overload of radioastronomical receivers at centimeter wavelengths; and unintentional radio emissions associated with massive amounts of microwave power or with the presence of large, warm structures in orbit causing the satellites to appear as individual stationary radio sources; finally, the fixed location of the geostationary satellite orbits would result in fixed regions of the sky being unusable for observations

The Lead Ion accelerating facility and the relative experimental program at CERN SPS fixed target

International Nuclear Information System (INIS)

Riccati, L.

1995-01-01

The status of the lead beam construction and commissioning is reviewed. A very wide experimental program with heavy nuclei was approved at the CERN SPS for a dedicated study of ultrarelativistic nucleus-nucleus collisions. An arbitrary and very short summary of the advantages and motivations for the use of heavier nuclei in the quark-gluon plasma search will be presented. ((orig.))

Prospects for the study of the {tau}-System in SPS1a' at the ILC

Energy Technology Data Exchange (ETDEWEB)

Bechtle, P.; Berggren, M.; List, J. [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Stempel, O. [Univ. Hamburg, Inst. fuer Experimentalphysik (Germany); Schade, P. [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Univ. Hamburg, Inst. fuer Experimentalphysik (Germany)

2009-08-15

The prospects for the analysis of {tau} channels at the SUSY benchmark point SPS1a', especially from e{sup +}e{sup -} {yields} {tau}{sub 1}{sup +}{tau}{sub 1}{sup -} and e{sup +}e{sup -} {yields} {tau}{sub 2}{sup +}{tau}{sub 2}{sup -}, have been studied in full simulation of the ILD detector concept forseen for the International Linear Collider. All accessible SUSY channels as well as all Standard Model backgrounds were generated at a centre-of-mass energy E{sub CMS}=500 GeV, including the beam energy spectrum and beam backgrounds expected for nominal ILC beam parameters. With an integrated luminosity of 500 fb{sup -1} delivered to the experiment, the masses of the {tau}{sub 1} and {tau}{sub 2} can be measured to 107.69{sub -0.06}{sup +0.03} GeV{+-}1.1 . {delta}M{sub {chi}{sub 1}{sup 0}} and 183{sub -5}{sup +11} GeV{+-}18 . {delta}M{sub {chi}{sub 1}{sup 0}}, respectively, while the true values in SPS1a' are 107.9 GeV and 194.9 GeV, respectively. The cross sections for {tau}{sub 1} and {tau}{sub 2} pair production could be obtained with a precision of 3.1 % and 4.2 %, respectively. Combining the mass and cross section measurement in the {tau}{sub 2} channel allows to determine the LSP mass with a relative error of 1.7 %, assuming a known mixing angle. In {tau}{sub 1} {yields} {tau}{chi}{sub 1}{sup 0} decays, the {tau} polarisation is measured to be 91{+-}9 % and 87.0{+-}3.4 % in the {pi} and {rho} decay channels of the {tau}, respectively. The true value in the simulated SPS1a' sample is 89.6 %. (orig.)

An Operations Management System for the Space Station

Science.gov (United States)

Rosenthal, H. G.

1986-09-01

This paper presents an overview of the conceptual design of an integrated onboard Operations Management System (OMS). Both hardware and software concepts are presented and the integrated space station network is discussed. It is shown that using currently available software technology, an integrated software solution for Space Station management and control, implemented with OMS software, is feasible.

Most critical collimator-mask-magnet sequence in the SPS-to-LHC transfer lines: energy deposition study.

CERN Document Server

Marzo, Matteo; Lechner, Anton; Vlachoudis, Vasilis

2017-01-01

This technical note refers to a study on the relation between the impact conditions of the SPS 450GeV proton beam and the energy deposited downstream the Target Collimator Dump In- jection Long (TCDIL) collimators [1], in the SPS-to-LHC transfer lines TI2 and TI8. Such an analysis is relevant in order to simulate the worst scenario of failure, in case the beam impacts on the TCDIL collimator’s jaw, in the frame of the LHC Injectors Upgrade (LIU), in view of the High Luminosity LHC (HL-LHC) phase. Previous studies already showed the dependency of the energy deposited in the downstream masks on the collimators-masks distance [2]. In absence of a (realistic) impact parameter, we perform now a study to select the most pessimistic one, trying to understand the origin of the various components responsible for the energy deposition on the downstream mask and magnet. The set up of the Monte Carlo FLUKA [3] [4] simulations and the most relevant results will be presented in this document. A sensitivity analysis was a...

Modification of jet-like correlations in Pb-Au at the SPS

International Nuclear Information System (INIS)

Appelshaeuser, Harald; Kniege, Stefan

2009-01-01

A study of high-p t two-particle azimuthal correlations in Pb-Au at √(S NN )=17,2GeV by the CERES experiment at the CERN-SPS, is presented. A broad away-side correlation with significant dip at Δφ∼π is observed. The shape and magnitude of the correlation is similar to measurements at RHIC. In comparison to PYTHIA calculations, we observe a significant excess of soft particles at the away-side. A study of charge correlations between trigger and associated particles disfavors vacuum fragmentation of the away-side jet and suggests significant energy transfer of the hard-scattered parton to the medium.

High statistics inclusive phi-meson production at SPS energies

International Nuclear Information System (INIS)

Dijkstra, H.B.

1985-01-01

This thesis describes an experiment studying the inclusive reaction hadron + Be → phi + anything → K + + K - + anything in 100 GeV/c, 120 GeV/c and 200 GeV/c hadron interactions. A total of 8x10 6 events were recorded using both positively and negatively charged unseparated hadron beams supplied by the CERN SPS. The experiment made use of an intelligent on-line event selection system based on micro-processors (FAMPs) in conjunction with a system of large MWPCs to increase the number of phi-events recorded per unit time. In 32 days of data taking over 600,000 phi-mesons were recorded onto magnetic tape. The physics motivation for collecting a large statistics sample of inclusive phi-mesons was the investigation of the inclusive phi-meson production mechanism and phi-spectroscopy. (Auth.)

The New SPS Extraction Channel for LHC and CNGS

CERN Document Server

Goddard, B; Schröder, G; Weterings, W; Uythoven, J

2000-01-01

The Large Hadron Collider (LHC) and CERN Neutrino to Gran Sasso (CNGS) projects require the construction of a new fast-extraction system in the long straight section LSS4 of the Super Proton Synchrotron (SPS) at CERN. A conventional DC septum magnet will be used, in conjunction with the installation of horizontal and vertical extraction bumpers, main quadrupoles with enlarged apertures, extraction kicker magnets and additional hardware protection, instrumentation, controls and electronics. The extraction channel must be able to accept the bright LHC proton beam at 450 GeV/c, and also the high intensity, large emittance fixed target CNGS proton beam at the nominal 400 GeV/c extraction momentum. This paper describes the extraction channel to be installed in 2003, and shows how the requirements for both the LHC and CNGS project can be met.

Pure & crystallized 2D Boron Nitride sheets synthesized via a novel process coupling both PDCs and SPS methods

Science.gov (United States)

Yuan, Sheng; Linas, Sébastien; Journet, Catherine; Steyer, Philippe; Garnier, Vincent; Bonnefont, Guillaume; Brioude, Arnaud; Toury, Bérangère

2016-02-01

Within the context of emergent researches linked to graphene, it is well known that h-BN nanosheets (BNNSs), also referred as 2D BN, are considered as the best candidate for replacing SiO2 as dielectric support or capping layers for graphene. As a consequence, the development of a novel alternative source for highly crystallized h-BN crystals, suitable for a further exfoliation, is a prime scientific issue. This paper proposes a promising approach to synthesize pure and well-crystallized h-BN flakes, which can be easily exfoliated into BNNSs. This new accessible production process represents a relevant alternative source of supply in response to the increasing need of high quality BNNSs. The synthesis strategy to prepare pure h-BN is based on a unique combination of the Polymer Derived Ceramics (PDCs) route with the Spark Plasma Sintering (SPS) process. Through a multi-scale chemical and structural investigation, it is clearly shown that obtained flakes are large (up to 30 μm), defect-free and well crystallized, which are key-characteristics for a subsequent exfoliation into relevant BNNSs.

Spark Plasma Sintering (SPS)-Assisted Synthesis and Thermoelectric Characterization of Magnéli Phase V6O11

KAUST Repository

Joos, Markus

2018-01-11

The Magnéli phase V6O11 was synthesized in gram amounts from a powder mixture of V6O11/V7O13 and vanadium metal, using the spark plasma sintering (SPS) technique. Its structure was determined with synchrotron X-ray powder diffraction data from a phase-pure sample synthesized by conventional solid-state synthesis. A special feature of Magnéli-type oxides is a combination of crystallographic shear and intrinsic disorder that leads to relatively low lattice thermal conductivities. SPS prepared V6O11 has a relatively low thermal conductivity of κ = 2.72 ± 0.06 W (m K)-1 while being a n-type conductor with an electrical conductivity of σ = 0.039 ± 0.005 (μΩ m)-1, a Seebeck coefficient of α = -(35 ± 2) μV K-1, which leads to a power factor of PF = 4.9 ± 0.8 × 10-5W (m K2)-1 at ∼600 K. Advances in the application of Magnéli phases are mostly hindered by synthetic and processing challenges, especially when metastable and nanostructured materials such as V6O11 are involved. This study gives insight into the complications of SPS-assisted synthesis of complex oxide materials, provides new information about the thermal and electrical properties of vanadium oxides at high temperatures, and supports the concept of reducing the thermal conductivity of materials with structural building blocks such as crystallographic shear (CS) planes.

Spark Plasma Sintering (SPS)-Assisted Synthesis and Thermoelectric Characterization of Magnéli Phase V6O11

KAUST Repository

Joos, Markus; Cerretti, Giacomo; Veremchuk, Igor; Hofmann, Patrick; Frerichs, Hajo; Anjum, Dalaver H.; Reich, Tobias; Lieberwirth, Ingo; Panthö fer, Martin; Zeier, Wolfgang G.; Tremel, Wolfgang

2018-01-01

The Magnéli phase V6O11 was synthesized in gram amounts from a powder mixture of V6O11/V7O13 and vanadium metal, using the spark plasma sintering (SPS) technique. Its structure was determined with synchrotron X-ray powder diffraction data from a phase-pure sample synthesized by conventional solid-state synthesis. A special feature of Magnéli-type oxides is a combination of crystallographic shear and intrinsic disorder that leads to relatively low lattice thermal conductivities. SPS prepared V6O11 has a relatively low thermal conductivity of κ = 2.72 ± 0.06 W (m K)-1 while being a n-type conductor with an electrical conductivity of σ = 0.039 ± 0.005 (μΩ m)-1, a Seebeck coefficient of α = -(35 ± 2) μV K-1, which leads to a power factor of PF = 4.9 ± 0.8 × 10-5W (m K2)-1 at ∼600 K. Advances in the application of Magnéli phases are mostly hindered by synthetic and processing challenges, especially when metastable and nanostructured materials such as V6O11 are involved. This study gives insight into the complications of SPS-assisted synthesis of complex oxide materials, provides new information about the thermal and electrical properties of vanadium oxides at high temperatures, and supports the concept of reducing the thermal conductivity of materials with structural building blocks such as crystallographic shear (CS) planes.

Mission Analysis for LEO Microwave Power-Beaming Station in Orbital Launch of Microwave Lightcraft

Science.gov (United States)

Myrabo, L. N.; Dickenson, T.

2005-01-01

A detailed mission analysis study has been performed for a 1 km diameter, rechargeable satellite solar power station (SPS) designed to boost 20m diameter, 2400 kg Micr,oWave Lightcraft (MWLC) into low earth orbit (LEO) Positioned in a 476 km daily-repeating oi.bit, the 35 GHz microwave power station is configured like a spinning, thin-film bicycle wheel covered by 30% efficient sola cells on one side and billions of solid state microwave transmitter elements on the other, At the rim of this wheel are two superconducting magnets that can stor,e 2000 G.J of energy from the 320 MW, solar array over a period of several orbits. In preparation for launch, the entire station rotates to coarsely point at the Lightcraft, and then phases up using fine-pointing information sent from a beacon on-board the Lightcraft. Upon demand, the station transmits a 10 gigawatt microwave beam to lift the MWLC from the earth surface into LEO in a flight of several minutes duration. The mission analysis study was comprised of two parts: a) Power station assessment; and b) Analysis of MWLC dynamics during the ascent to orbit including the power-beaming relationships. The power station portion addressed eight critical issues: 1) Drag force vs. station orbital altitude; 2) Solar pressure force on the station; 3) Station orbital lifetime; 4) Feasibility of geo-magnetic re-boost; 5) Beta angle (i..e., sola1 alignment) and power station effective area relationship; 6) Power station percent time in sun vs, mission elapsed time; 7) Station beta angle vs.. charge time; 8) Stresses in station structures.. The launch dynamics portion examined four issues: 1) Ascent mission/trajecto1y profile; 2) MWLC/power-station mission geometry; 3) MWLC thrust angle vs. time; 4) Power station pitch rate during power beaming. Results indicate that approximately 0 58 N of drag force acts upon the station when rotated edge-on to project the minimum frontal area of 5000 sq m. An ion engine or perhaps an electrodynamic

Test~of~Beam~Extraction~by~Crystal~Channeling~at~the~SPS: A First Step towards a LHC Extracted Beam

CERN Multimedia

2002-01-01

% RD22 \\\\ \\\\ The availability of a beam extracted out of the LHC accelerator would open up very interesting possibilities for B-physics, in particular for the study of CP-violation. Channeling in bent crystals appears to be the most promising method to produce an extracted beam of intensity $\\sim$~10$^{8}$ p/sec. This would provide as many as 10$^{10}$ $ B \\bar{B} $ pairs per year of run, two orders of magnitude more than could be produced by an e$^+$e$^-$ B-factory with L~=~10$^{34}$ cm$^{-2}$s$^{-1}$ We propose a R\\&D program to study beam extraction at the CERN SPS, using a silicon bent crystal to be installed in the SPS beam pipe and placed next to the beam in such a way as to intercept the beam halo. Transverse excitation of the beam in presence of non-linearities will be used to create halo conditions similar to what are expected for LHC.

SRS station 16.3: high-resolution applications

CERN Document Server

Murphy, B M; Golshan, M; Moore, M; Reid, J; Kowalski, G

2001-01-01

Station 16.3 is a high-resolution X-ray diffraction beamline at Daresbury Laboratory Synchrotron Radiation Source. The data presented demonstrate the high-resolution available on the station utilising the recently commissioned four-reflection Si 1 1 1 monochromator and three-reflection Si 1 1 1 analyser. For comparison, a reciprocal space map of the two-bounce Si 1 1 1 monochromator and two-bounce analyser is also shown. Operation of the station is illustrated with examples for silicon, and for diamond. Lattice parameter variations were measured with accuracies in the part per million range and lattice tilts at the arc second level (DuMond, Phys. Rev. 52 (1937) 872).

Revealing Partons in Hadrons: From the ISR to the SPS Collider

CERN Document Server

Darriulat, Pierre

2015-01-01

Our understanding of the structure of hadrons has developed during the seventies and early eighties from a few vague ideas to a precise theory, Quantum Chromodynamics, that describes hadrons as made of elementary partons (quarks and gluons). Deep inelastic scattering of electrons and neutrinos on nucleons and electron–positron collisions have played a major role in this development. Less well known is the role played by hadron collisions in revealing the parton structure, studying the dynamic of interactions between partons and offering an exclusive laboratory for the direct study of gluon interactions. The present article recalls the decisive contributions made by the CERN Intersecting Storage Rings and, later, the proton–antiproton SPS Collider to this chapter of physics.

Recent results on (anti)nucleus and (anti)hyperon production in nucleus-nucleus collisions at CERN SPS energies

CERN Document Server

Melkumov, G L; Anticic, T; Baatar, B; Barna, D; Bartke, J; Betev, L; Bialkowska, H; Blume, C; Boimska, B; Botje, M; Bracinik, J; Bramm, R; Buncic, P; Cerny, V; Christakoglou, P; Chung, P; Chvala, O; Cramer, J G; Csató, P; Dinkelaker, P; Eckardt, V; Flierl, D; Fodor, Z; Foka, P; Friese, V; Gál, J; Gazdzicki, M; Genchev, V; Georgopoulos, G; Grebieszkow, K; Hegyi, S; Höhne, C; Kadija, K; Karev, A; Kikola, D; Gladysz-Dziadus, E; Kliemant, M; Kniege, S; Kolesnikov, V I; Kornas, E; Korus, R; Kowalski, M; Kraus, I; Kreps, M; Laszlo, A; Lacey, R; Van Leeuwen, M; Lvai, P; Litov, L; Lungwitz, B; Makariev, M; Malakhov, A I; Mateev, M; Melkumov, G L; Mischke, A; Mitrovski, M; Molnár, J; Mrówczynski, S; Nicolic, V; Pálla, G; Panagiotou, A D; Panayotov, D; Petridis, A; Peryt, W; Pikna, M; Pluta, J; Prindle, D; Pühlhofer, F; Renfordt, R; Roland, C; Roland5, G; Rybczynski, M; Rybicki, A; Sandoval, A; Schmitz, N; Schuster, T; Siklér, F; Sitár, B; Skrzypczak, E; Slodkowski, M; Stefanek, G; Stock, R; Seyboth, P; Strabel, C; Ströbele, H; Susa, T; Szentpetery, I; Sziklai, J; Szuba, M; Szymanski, P; Trubnikov, V; Varga, D; Vassiliou, M; Veres, G I; Vesztergombi, G; Vranic, D; Wlodarczyk, Z; Wojtaszek11, A; Yoo, I K; Zimnyi, J; Wetzler, A

2007-01-01

The NA49 experiment has collected comprehensive data on particle production in nucleus-nucleus collisions over the whole SPS beam energies range, the critical energy domain where the expected phase transition to a deconfined phase is expected to occur. The latest results from Pb+Pb collisions between 20$A$ GeV and 158$A$ GeV on baryon stopping and light nuclei production as well as those for strange hyperons are presented. The measured data on $p$, $\\bar{p}$, $\\Lambda$, $\\bar{\\Lambda}$, $\\Xi^-$ and $\\bar{\\Xi}^+$ production were used to evaluate the rapidity distributions of net-baryons at SPS energies and to compare with the results from the AGS and the RHIC for central Pb+Pb (Au+Au) collisions. The dependence of the yield ratios and the inverse slope parameter of the $m_t$ spectra on the collision energy and centrality, and the mass number of the produced nuclei $^3He$, $t$, $d$ and $\\bar{d}$ are discussed within coalescence and statistical approaches. Analysis of the total multiplicity exhibits remarkable a...

Safety planning for nuclear power stations

International Nuclear Information System (INIS)

Tadmor, J.

1979-01-01

The article shows that compared to the many industries and other human activities, nuclear power stations are among the safest. A short description of the measures taken to prevent accidents and of the additional safety means entering into action if an accident does occur is presented. It is shown that in nuclear plants the death frequency following malfunctioning is 1 death in 100.000 years whereas deaths following other human activities is 1 in 2 to 100 years and following natural calamities like earthquakes and floods is 1 in 10 years. As an example it is shown that for a population of 15.000.000 living in a radius of 40 km around 100 power stations the average number of deaths will be of 2 per year as compared to 4200 from road accidents with the corresponding number of injuries of 20 and 375.000 respectively. (B.G.)

Measurement of meson resonance production in π"- + C interactions at SPS energies

International Nuclear Information System (INIS)

Aduszkiewicz, A.; Dominik, W.; Kuich, M.; Matulewicz, T.; Podlaski, P.; Posiadala, M.; Walewski, M.; Ali, Y.; Brzychczyk, J.; Larsen, D.; Planeta, R.; Richter-Was, E.; Staszel, P.; Wyszynski, O.; Andronov, E.V.; Feofilov, G.A.; Igolkin, S.N.; Kovalenko, V.N.; Lazareva, T.V.; Merzlaya, A.O.; Seryakov, A.Yu.; Valiev, F.F.; Vechernin, V.V.; Anticic, T.; Kadija, K.; Susa, T.; Baatar, B.; Bunyatov, S.A.; Kireyeu, V.A.; Kolesnikov, V.I.; Krasnoperov, A.; Lyubushkin, V.V.; Malakhov, A.I.; Matveev, V.; Melkumov, G.L.; Tereshchenko, V.; Baszczyk, M.; Dorosz, P.; Kucewicz, W.; Mik, L.; Bhosale, S.; Davis, N.; Kielbowicz, M.; Marcinek, A.; Ozvenchuk, V.; Rybicki, A.; Blondel, A.; Bravar, A.; Damyanova, A.; Haesler, A.; Korzenev, A.; Ravonel, M.; Bogomilov, M.; Kolev, D.; Tsenov, R.; Brandin, A.; Selyuzhenkov, I.; Strikhanov, M.; Taranenko, A.; Busygina, O.; Golubeva, M.; Guber, F.; Ivashkin, A.; Kurepin, A.; Sadovsky, A.; Cherif, H.; Deveaux, M.; Klochkov, V.; Koziel, M.; Renfordt, R.; Snoch, A.; Stroebele, H.; Toia, A.; Cirkovic, M.; Manic, D.; Puzovic, J.; Czopowicz, T.; Grebieszkow, K.; Mackowiak-Pawlowska, M.; Maksiak, B.; Slodkowski, M.; Tefelska, A.; Tefelski, D.; Dembinski, H.; Engel, R.; Faas, S.; Garrido, X.; Herve, A.E.; Maris, I.C.; Mathes, H.J.; Roth, M.; Ruprecht, M.; Szuba, M.; Ulrich, R.; Unger, M.; Veberic, D.; Dumarchez, J.; Zambelli, L.; Ereditato, A.; Francois, C.; Pistillo, C.; Wilkinson, C.; Fodor, Z.; Garibov, A.; Gazdzicki, M.; Hylen, J.; Lundberg, B.; Marchionni, A.; Rameika, R.; Zwaska, R.; Johnson, S.R.; Marino, A.D.; Nagai, Y.; Rumberger, B.T.; Zimmerman, E.D.; Kaptur, E.; Kowalski, S.; Lysakowski, B.; Pulawski, S.; Schmidt, K.; Kowalik, K.; Rondio, E.; Stepaniak, J.; Laszlo, A.; Marton, K.; Lewicki, M.; Naskret, M.; Turko, L.; Messerly, B.; Paolone, V.; Wickremasinghe, A.; Mills, G.B.; Morozov, S.; Petukhov, O.; Mrowczynski, S.; Rybczynski, M.; Seyboth, P.; Stefanek, G.; Wlodarczyk, Z.; Wojtaszek-Szwarc, A.; Pavin, M.; Popov, B.A.; Rauch, W.; Roehrich, D.; Rustamov, A.

2017-01-01

We present measurements of ρ"0, ω and K"*"0 spectra in π"- + C production interactions at 158 GeV/c and ρ"0 spectra at 350 GeV/c using the NA61/SHINE spectrometer at the CERN SPS. Spectra are presented as a function of the Feynman's variable x F in the range 0 < x_F < 1 and 0 < x_F < 0.5 for 158 and 350 GeV/c respectively. Furthermore, we show comparisons with previous measurements and predictions of several hadronic interaction models. These measurements are essential for a better understanding of hadronic shower development and for improving the modeling of cosmic ray air showers. (orig.) 5

A study on friction welding of localized SPS5 spring steel

Energy Technology Data Exchange (ETDEWEB)

Jeong, S. U. [Gyeongsang National Univ., Jinju (Korea, Republic of)

2000-07-01

This thesis studied whether friction welding of SPS5, localized torsion bar material could be accomplished or not. And then optimum welding conditions were examined and leaded through tensile, impact, torsion and hardness test after postweld heat treatment of the actual field condition. Obtained results were as follows; linear relationship was existed between heating time and total upset, and a quadratic equation model could be made between tensile strength and heating time. Optimum welding conditions with fine structure were as follows in case total upset(U)= 8.5mm; the number of rotations(n)= 2,000 rpm, heating pressure(p{sub 1})= 80 MPa, upset pressure(P{sub 2})200 MPa, heating time(t{sub 1})= 4 sec, upset time(t{sub 2})= 3 sec.

Hydrodynamic Tunneling of 440 GeV SPS protons in Solid Material: Production of Warm Dense Matter at CERN HiRadMat Facility

Science.gov (United States)

Tahir, Naeem Ahmad; Blanco Sancho, Juan; Schmidt, Ruediger; Shutov, Alaxander; Burkart, Florian; Wollmann, Daniel; Piriz, Antonio Roberto

2013-10-01

Numerical simulations have shown that the range of 7 TeV LHC protons in solid matter will be significantly increased due to hydrodynamic tunneling. For example, in solid copper and solid carbon, these protons and the shower can penetrate up to 35 m and 25 m, respectively. However, their corresponding static range in the two materials is 1 m and 3 m, respectively. This will have important implications on machine protection design. In order to validate these simulation results, experiments have been performed at the CERN HiRadMat facility using the 440 GeV SPS proton beam irradiating solid copper cylindrical target. The phenomenon of hydrodynamic tunneling has been experimentally confirmed and good agreement has been found between the simulations and the experimental results. A very interesting outcome of this work is that the HiRadMat facility can be used to generate High Energy Density matter including Warm Dense Matter and strongly coupled plasmas in the laboratory.

Study of high energy densities over extended nuclear volumes via nucleus-nucleus collisions at the SPS

CERN Multimedia

2002-01-01

This experiment examines in detail the characteristics of ultra-relativistic nucleus-nucleus interactions using $^{16}$O beams of 200 GeV/A from the SPS. The experiment combines 4$\\pi$ calorimeter coverage with measurements of inclusive particle spectra, two-particle correlations, low and high-mass lepton pairs and photons. A multiwire active target allows maximum interaction rates with a minimum of secondary interactions. Additional data are taken with an emulsion target.

Blast-wave analysis of strange particle $m_{T}$ spectra in Pb-Pb collisions at the SPS

CERN Document Server

Bruno, Giuseppe E

2005-01-01

The transverse mass spectra of high statistics, high purity samples of K/sup 0//sub S/, Lambda , Xi and Omega particles produced in Pb-Pb collisions at SPS energy have been studied in the framework of the blast-wave model. The dependence of the freezeout parameters on particle species and event centrality is discussed. Results at 40 A GeV/c are presented here for the first time.

Reviewing nuclear power station achievement

International Nuclear Information System (INIS)

Howles, L.R.

1976-01-01

For measurement of nuclear power station achievement against original purchase the usual gross output figures are of little value since the term loosely covers many different definitions. An authentically designed output figure has been established which relates to net design output plus house load at full load. Based on these figures both cumulative and moving annual load factors are measured, the latter measuring the achievement over the last year, thus showing trends with time. Calculations have been carried out for all nuclear stations in the Western World with 150 MW(e) gross design output and above. From these are shown: moving annual load factor indicating relative station achievements for all the plants; cumulative load factors from which return of investment can be calculated; average moving annual load factors for the four types of system Magnox, PWR, HWR, and BWR; and a relative comparison of achievement by country in a few cases. (U.K.)

OBS Technologies and permanent seismic Stations at Sea

Science.gov (United States)

Makris, J.; Nikolova, S. B.

2003-04-01

An off-shore telemetric system was developed during last 2 years. It consists of a buoy unit, OBS with seismic sensor and digitizer at the sea floor and coaxial cable for transferring data from the sea. The buoy unit includes all components for recording and transmitting data to the base station. A solar panel and wind generator are the sources of energy that charge the batteries in the buoy. An Omni directional antenna and a radio modem are used for data transfer. The buoy can be connected also to mobile network or satellite. The Seismic recording unit is SEDIS IV developed in GeoPro GmbH which is a 6 channel data logger equipped with a hard disk of 30 GByte capacity and a flash memory of 0.5 Gbyte which can continuously record at different sampling rate (from 31.25 to 1000sps). The operating system for SEDIS IV is LINUX, with possible data compression, event location and extraction. The data transfer and supply of the power to seismometer and ADC unit in OBS sphere is done through coaxial cable, connecting the buoy unit and OBS. The whole system was tested for a period of one month (October 2002) within frame of Nestor program in Pilos (Greece) and worked successfully.

Atmospheric air contamination monitoring. Monitoring station ASS-500, GIG Katowice

International Nuclear Information System (INIS)

Michalik, B.

1993-01-01

The results obtained during the period of 1991-1993 in monitoring station ASS-500 working in Katowice have been presented. The concentration of 137 Cs, 226 Ra, 40 K, 7 Be and dustiness in atmospheric air have been shown. Some proposals about the modifications of monitoring station ASS-500 have been introduced. 3 figs, 5 tabs

The Run Control system of the NA62 experiment at CERN SPS

CERN Document Server

Lazzeroni, Cristina

2016-01-01

The NA62 experiment at CERN SPS started physics data taking this year with the aim to measure the ultra-rare decay K + → π +νν¯. The experiment consists of a large number of subsystems to reach the goal of 10 % accuracy and less than 10 % background. The Run Control has been designed to link their trigger and data acquisition system in a single central application easily controllable by non-expert shifters. It has been continuously evolving over time, integrating new equipments, following new requirements and feedback from shifters. The next steps of development is a more automatized system that integrates the knowledge acquired during the operation of the experiment.

Excavation of the SPS tunnel (view of a section prior to lining by a concrete shell)

CERN Multimedia

1974-01-01

The SPS ring (6911 m in circumference) is housed at a depth of 40 m (average) under the surface. The tunnel with an overall cross-sectional diameter of 4.8 m was drilled by big tunnelling machines (see 7406022X, 7406027X) into the molasse rock present in the Geneva basin. After the passage of the tunnelling machine the tunnel walls were lined with a concrete layer of about 30cm thickness.

Energy consumption analysis for the Mars deep space station

Science.gov (United States)

Hayes, N. V.

1982-01-01

Results for the energy consumption analysis at the Mars deep space station are presented. It is shown that the major energy consumers are the 64-Meter antenna building and the operations support building. Verification of the antenna's energy consumption is highly dependent on an accurate knowlege of the tracking operations. The importance of a regular maintenance schedule for the watt hour meters installed at the station is indicated.

Experience with workstations for accelerator control at the CERN SPS

International Nuclear Information System (INIS)

Ogle, A.; Ulander, J.; Wilkie, I.

1990-01-01

The CERN super proton synchrotron (SPS) control system is currently undergoing a major long-term upgrade. This paper reviews progress on the high-level application software with particular reference to the operator interface. An important feature of the control-system upgrade is the move from consoles with a number of fixed screens and limited multitasking ability to workstations with the potential to display a large number of windows and perform a number of independent tasks simultaneously. This workstation environment thus permits the operator to run tasks in one machine for which he previously had to monopolize two or even three old consoles. However, the environment also allows the operator to cover the screen with a multitude of windows, leading to complete confusion. Initial requests to present some form of 'global status' of the console proved to be naive, and several iterations were necessary before the operators were satisfied. (orig.)

Creep of Polycrystalline Magnesium Aluminate Spinel Studied by an SPS Apparatus.

Science.gov (United States)

Ratzker, Barak; Sokol, Maxim; Kalabukhov, Sergey; Frage, Nachum

2016-06-20

A spark plasma sintering (SPS) apparatus was used for the first time as an analytical testing tool for studying creep in ceramics at elevated temperatures. Compression creep experiments on a fine-grained (250 nm) polycrystalline magnesium aluminate spinel were successfully performed in the 1100-1200 °C temperature range, under an applied stress of 120-200 MPa. It was found that the stress exponent and activation energy depended on temperature and applied stress, respectively. The deformed samples were characterized by high resolution scanning electron microscope (HRSEM) and high resolution transmission electron microscope (HRTEM). The results indicate that the creep mechanism was related to grain boundary sliding, accommodated by dislocation slip and climb. The experimental results, extrapolated to higher temperatures and lower stresses, were in good agreement with data reported in the literature.

Relación entre los mecanismos de difusión atómica y las propiedades ópticas en la sinterización por Spark Plasma Sintering (SPS de la alúmina.

Directory of Open Access Journals (Sweden)

Torrecillas, R.

2009-12-01

Full Text Available The control of the sintering parameters during spark plasma sintering (SPS of polycrystalline alumina allows modifying the contribution due to the different atomic diffusion mechanisms. Thus, changing the heating rate as a function of the sintering stage allows tailoring sintering cycles that optimize the final density of the material with a minimal grain growth. It is shown in this work how by using two heating rates, 100 and 4ºC/min, allows obtaining a polycrystalline transparent alumina with a higher real in-line transmittance than that obtained with constant heating rates sintering cycles.

El control de los parámetros de sinterización de la alúmina policristalina por spark plasma sintering (SPS permite modificar la contribución de los diferentes mecanismos de difusión atómica. Así, variar la rampa de calentamiento en función de la etapa de sinterización permite diseñar ciclos de sinterización que optimizan la densidad final del material con un mínimo crecimiento de grano. En este trabajo se demuestra cómo empleando dos velocidades, 100 y 4ºC/min, es posible obtener una alúmina policristalina con una transmitancia real en línea superior a la obtenida en ciclos con rampas constantes.

Gluon saturation and baryon stopping in the SPS, RHIC, and LHC energy regions

International Nuclear Information System (INIS)

Li Shuang; Feng Shengqin

2012-01-01

A new geometrical scaling method with a gluon saturation rapidity limit is proposed to study the gluon saturation feature of the central rapidity region of relativistic nuclear collisions. The net-baryon number is essentially transported by valence quarks that probe the saturation regime in the target by multiple scattering. We take advantage of the gluon saturation model with geometric scaling of the rapidity limit to investigate net baryon distributions, nuclear stopping power and gluon saturation features in the SPS and RHIC energy regions. Predictions for net baryon rapidity distributions, mean rapidity loss and gluon saturation feature in central Pb + Pb collisions at the LHC are made in this paper. (authors)

The Social Interaction Anxiety Scale (SIAS) and the Social Phobia Scale (SPS): a comparison of two short-form versions.

Science.gov (United States)

Fergus, Thomas A; Valentiner, David P; Kim, Hyun-Soo; McGrath, Patrick B

2014-12-01

The widespread use of Mattick and Clarke's (1998) Social Interaction Anxiety Scale (SIAS) and Social Phobia Scale (SPS) led 2 independent groups of researchers to develop short forms of these measures (Fergus, Valentiner, McGrath, Gier-Lonsway, & Kim, 2012; Peters, Sunderland, Andrews, Rapee, & Mattick, 2012). This 3-part study examined the psychometric properties of Fergus et al.'s and Peters et al.'s short forms of the SIAS and SPS using an American nonclinical adolescent sample in Study 1 (N = 98), American patient sample with an anxiety disorder in Study 2 (N = 117), and both a South Korean college student sample (N = 341) and an American college student sample (N = 550) in Study 3. Scores on both sets of short forms evidenced adequate internal consistency, interitem correlations, and measurement invariance. Scores on Fergus et al.'s short forms, particularly their SIAS short form, tended to capture more unique variance in scores of criterion measures than did scores on Peters et al.'s short forms. Implications for the use of these 2 sets of short forms are discussed. (c) 2014 APA, all rights reserved.

IMPROVEMENT OF THE CERN SPS ELECTROSTATIC SEPTA ION TRAPS

CERN Multimedia

Balhan, Bruno; Barlow, Roger Andrew; Raffaele, Graziano

2016-01-01

At CERN, the SPS synchrotron is equipped with a slow extraction channel towards the fixed target beam lines in the North Area This channel includes five consecutive electrostatic septa, where the field free region and the active high field region are separated by an array of tungsten-rhenium wires. The field-free region provides for the circulating beam, while the high field region is used to deflect the extracted beam. Since the residual gas can be ionized by the orbiting beam, low energy ions could cross the wire array and enter the high field region and cause high voltage breakdown when accelerated onto the cathode. To prevent low energy ions from entering this high electric field region, a vertical field is applied to the orbiting beam using so-called ‘ion traps’ for active protection. The vertical field is created by electrodes placed inside the region containing the circulating beam. Due to electromagnetic coupling onto the ion trap electrodes observed with the high frequency LHC beam (25 ns spaced ...

Proposal for SPS beam time for the baby MIND and TASD neutrino detector prototypes

CERN Document Server

Asfandiyarov, R.; Blondel, A.; Bogomilov, M.; Bross, A.; Cadoux, F.; Cervera, A.; Izmaylov, A.; Karadzhov, Y.; Karpikov, I.; Khabibulin, M.; Khotyantsev, A.; Kopylov, A.; Kudenko, Y.; Matev, R.; Mineev, O.; Musienko, Y.; Nessi, M.; Noah, E.; Rubbia, A.; Shaykiev, A.; Soler, P.; Tsenov, R.; Vankova-Kirilova, G.; Yershov, N.

2015-01-01

The design, construction and testing of neutrino detector prototypes at CERN are ongoing activities. This document reports on the design of solid state baby MIND and TASD detector prototypes and outlines requirements for a test beam at CERN to test these, tentatively planned on the H8 beamline in the North Area, which is equipped with a large aperture magnet. It is hoped that this will allow for the current proposal to be considered in light of the recently approved projects related to neutrino activities with the SPS in the North Area in the medium term 2015-2020.

Zirconia-mullite obtained from co-precipitated zirconia-mullite composite powders by SPS

Energy Technology Data Exchange (ETDEWEB)

Li, H.Z.; Li, Z.J.; Luo, X.D. [Univ. of Science and Technology Liaoning, Anshan (China). School of High Temperature Materials and Magnesium Resource Engineering; Gui, J.Y.; Xie, Z.P. [Tsinghua Univ., Beijing (China). School of Materials Science and Engineering

2016-07-01

The co-precipitation method is used to fabricate precursor powder. This powder is densified by means of the spark plasma sintering (SPS) technique at 1500 C with a holding time of 7 min to prepare zirconia-mullite samples. Their density measures up to 97 % of the theoretical density, and the sintered mullite compacts exhibit better strength properties (289 ± 12 MPa) and H{sub v} (9.99 GPa). The mode of fracture is changed with the addition of ZrO{sub 2} and extensive fine cleavages are observed on the grain surface. These cleavages join together to form steps, which can absorb more energy. The flexural strength of the samples is almost double that of pure mullite, which is related to the formation of cleavages.

The New RF Control System for the CERN SPS Accelerator

CERN Document Server

Baudrenghien, P; Linnecar, Trevor Paul R; Marty, H; Molendijk, J C; Pilchen, Y; Wehrle, U; Weierud, F

1996-01-01

The old SPS RF control system designed in 1972 has been replaced completely, i.e. both hardware and software. The new system has to control both RF equipment conceived during the last 23 years and future (modern) equipment. Using information analysis methods, we derived a model of an RF command and designed a data base accordingly (ORACLE®). Information from this data base is used for command generation and processing and also for archiving settings. The advantage is purely generic software, i.e. the same computer code is used for switching on an RF amplifier, as for setting a frequency synthesizer. New equipment is added very simply by entering new records in the data base. Additional features include a reservation scheme whereby a user can take private control of any piece of equipment, a reporting facility notifying the user of the simultaneous control activity by other users on RF equipment, and a capability scheme assigning a level of expertise to each user restricting action on the equipment.

ORBIT FEEDBACK CONTROL FOR THE LHC Prototyping at the SPS

CERN Document Server

Steinhagen, Ralph J

2004-01-01

The Large Hadron Collider (LHC) is the next generation proton collider that is presently built at CERN. The LHC will be installed in the former LEP (Large Electron Positron Collider) tunnel. The presence of a high intensity beam in an environment of cryogenic magnets requires an excellent control of particle losses from the beam. Eventually the performance of the LHC may be limited by the ability to control the beam losses. The performance of the LHC cleaning system depends critically on the beam position stability. Ground motion, field and alignment imperfections and beam manipulations may cause orbit movements. The role of the future LHC Orbit Feedback System is the minimisation of closed orbit perturbations by periodically measuring and steering the transverse beam position back to its reference position. This diploma thesis focuses on the design and prototyping of an orbit feedback system at the SPS. The design is based on a separation of the steering problem into space and time. While the correction in s...

Measurement of Nuclear Interaction Rates in Crystal Using the CERN-SPS North Area Test Beams

CERN Document Server

Losito, R; Taratin, A

2010-01-01

A number of tests were performed in the North area of the SPS in view of investigating crystal-particles interactions for future application in hadron colliders. The rate of nuclear interactions was measured with 400 GeV proton beams directed into a silicon bent crystal. In this way the background induced by the crystal either in amorphous or in channeling orientation was revealed. The results provide fundamental information to put in perspective the use of silicon crystals to assist halo collimation in hadron colliders, whilst minimizing the induced loss.

NESSiE: An experimental search for sterile neutrinos with the CERN-SPS beam

Science.gov (United States)

Medinaceli, E.; NESSiE Collaboration

2013-08-01

NESSiE (Neutrino Experiment with SpectrometerS in Europe) is an experiment dedicated to the search for sterile neutrinos beyond the Standard Model with the CERN-SPS neutrino beam. The experiment is based on two identical LAr-TPC's followed by magnetized spectrometers, observing the electron and muon neutrino events at the "Near" (600 m) and "Far" (1300 m) positions from the proton target. The main characteristics of the spectrometers are described here. Spectrometers will exploit a classical dipole magnetic field with iron slabs, and a new concept air-core magnet will perform charge identification and muon momentum measurements in the energy range from ∼ 100 MeV to few GeV over a large transverse area (> 50m2).

Measurement of meson resonance production in π{sup -} + C interactions at SPS energies

Energy Technology Data Exchange (ETDEWEB)

Aduszkiewicz, A.; Dominik, W.; Kuich, M.; Matulewicz, T.; Podlaski, P.; Posiadala, M.; Walewski, M. [University of Warsaw, Warsaw (Poland); Ali, Y.; Brzychczyk, J.; Larsen, D.; Planeta, R.; Richter-Was, E.; Staszel, P.; Wyszynski, O. [Jagiellonian University, Krakow (Poland); Andronov, E.V.; Feofilov, G.A.; Igolkin, S.N.; Kovalenko, V.N.; Lazareva, T.V.; Merzlaya, A.O.; Seryakov, A.Yu.; Valiev, F.F.; Vechernin, V.V. [St. Petersburg State University, St. Petersburg (Russian Federation); Anticic, T.; Kadija, K.; Susa, T. [Ruder Boskovic Institute, Zagreb (Croatia); Baatar, B.; Bunyatov, S.A.; Kireyeu, V.A.; Kolesnikov, V.I.; Krasnoperov, A.; Lyubushkin, V.V.; Malakhov, A.I.; Matveev, V.; Melkumov, G.L.; Tereshchenko, V. [Joint Institute for Nuclear Research, Dubna (Russian Federation); Baszczyk, M.; Dorosz, P.; Kucewicz, W.; Mik, L. [AGH University of Science and Technology, Krakow (Poland); Bhosale, S.; Davis, N.; Kielbowicz, M.; Marcinek, A.; Ozvenchuk, V.; Rybicki, A. [H. Niewodniczanski Institute of Nuclear Physics of the Polish Academy of Sciences, Krakow (Poland); Blondel, A.; Bravar, A.; Damyanova, A.; Haesler, A.; Korzenev, A.; Ravonel, M. [University of Geneva, Geneva (Switzerland); Bogomilov, M.; Kolev, D.; Tsenov, R. [University of Sofia, Faculty of Physics, Sofia (Bulgaria); Brandin, A.; Selyuzhenkov, I.; Strikhanov, M.; Taranenko, A. [National Research Nuclear University (Moscow Engineering Physics Institute), Moscow (Russian Federation); Busygina, O.; Golubeva, M.; Guber, F.; Ivashkin, A.; Kurepin, A.; Sadovsky, A. [Institute for Nuclear Research, Moscow (Russian Federation); Cherif, H.; Deveaux, M.; Klochkov, V.; Koziel, M.; Renfordt, R.; Snoch, A.; Stroebele, H.; Toia, A. [University of Frankfurt, Frankfurt (Germany); Cirkovic, M.; Manic, D.; Puzovic, J. [University of Belgrade, Belgrade (Serbia); Czopowicz, T.; Grebieszkow, K.; Mackowiak-Pawlowska, M.; Maksiak, B.; Slodkowski, M.; Tefelska, A.; Tefelski, D. [Warsaw University of Technology, Warsaw (Poland); Dembinski, H.; Engel, R.; Faas, S.; Garrido, X.; Herve, A.E.; Maris, I.C.; Mathes, H.J.; Roth, M.; Ruprecht, M.; Szuba, M.; Ulrich, R.; Unger, M.; Veberic, D. [Karlsruhe Institute of Technology, Karlsruhe (Germany); Dumarchez, J.; Zambelli, L. [University of Paris VI and VII, LPNHE, Paris (France); Ereditato, A.; Francois, C.; Pistillo, C.; Wilkinson, C. [University of Bern, Bern (Switzerland); Fodor, Z. [Wigner Research Centre for Physics of the Hungarian Academy of Sciences, Budapest (Hungary); University of Wroclaw, Wroclaw (Poland); Garibov, A. [National Nuclear Research Center, Baku (Azerbaijan); Gazdzicki, M. [University of Frankfurt, Frankfurt (Germany); Jan Kochanowski University in Kielce, Kielce (Poland); Hylen, J.; Lundberg, B.; Marchionni, A.; Rameika, R.; Zwaska, R. [Fermilab, Batavia (United States); Johnson, S.R.; Marino, A.D.; Nagai, Y.; Rumberger, B.T.; Zimmerman, E.D. [University of Colorado, Boulder (United States); Kaptur, E.; Kowalski, S.; Lysakowski, B.; Pulawski, S.; Schmidt, K. [University of Silesia, Katowice (Poland); Kowalik, K.; Rondio, E.; Stepaniak, J. [National Centre for Nuclear Research, Warsaw (Poland); Laszlo, A.; Marton, K. [Wigner Research Centre for Physics of the Hungarian Academy of Sciences, Budapest (Hungary); Lewicki, M.; Naskret, M.; Turko, L. [University of Wroclaw, Wroclaw (Poland); Messerly, B.; Paolone, V.; Wickremasinghe, A. [University of Pittsburgh, Pittsburgh (United States); Mills, G.B. [Los Alamos National Laboratory, Los Alamos (United States); Morozov, S.; Petukhov, O. [Institute for Nuclear Research, Moscow (Russian Federation); National Research Nuclear University (Moscow Engineering Physics Institute), Moscow (Russian Federation); Mrowczynski, S.; Rybczynski, M.; Seyboth, P.; Stefanek, G.; Wlodarczyk, Z.; Wojtaszek-Szwarc, A. [Jan Kochanowski University in Kielce, Kielce (Poland); Pavin, M. [Ruder Boskovic Institute, Zagreb (Croatia); University of Paris VI and VII, LPNHE, Paris (France); Popov, B.A. [University of Paris VI and VII, LPNHE, Paris (France); Joint Institute for Nuclear Research, Dubna (Russian Federation); Rauch, W. [Fachhochschule Frankfurt, Frankfurt (Germany); Roehrich, D. [University of Bergen, Bergen (Norway); Rustamov, A. [National Nuclear Research Center, Baku (Azerbaijan); University of Frankfurt, Frankfurt (Germany); Collaboration: The NA61/SHINE Collaboration

2017-09-15

We present measurements of ρ{sup 0}, ω and K{sup *0} spectra in π{sup -} + C production interactions at 158 GeV/c and ρ{sup 0} spectra at 350 GeV/c using the NA61/SHINE spectrometer at the CERN SPS. Spectra are presented as a function of the Feynman's variable x F in the range 0 < x{sub F} < 1 and 0 < x{sub F} < 0.5 for 158 and 350 GeV/c respectively. Furthermore, we show comparisons with previous measurements and predictions of several hadronic interaction models. These measurements are essential for a better understanding of hadronic shower development and for improving the modeling of cosmic ray air showers. (orig.) 5.

Search for the QCD critical point in nuclear collisions at 158A GeV at the CERN Super Proton Synchrotron (SPS)

NARCIS (Netherlands)

Anticic, T.; Botje, M.A.J.|info:eu-repo/dai/nl/070139032; Christakoglou, P.; van Leeuwen, M.|info:eu-repo/dai/nl/250599171

2010-01-01

Pion production in nuclear collisions at the Super Proton Synchrotron (SPS) is investigated with the aim to search, in a restricted domain of the phase diagram, for power laws in the behavior of correlations that are compatible with critical QCD. We analyzed interactions of nuclei of different sizes

Spectral characteristics of seismic noise using data of Kazakhstan monitoring stations

International Nuclear Information System (INIS)

Mikhajlova, N.N.; Komarov, I.I.

2006-01-01

Spectral specifications of seismic noise research for PS23-Makanchi, Karatau, Akbulak, AS057-Borovoye and new three-component station AS059-Aktyubinsk was done. Spectral noise density models were obtained for day and night time and spectral density values variation. Noise close to low-level universal noise model is peculiar for all stations, which provides their high efficiency while seismic monitoring. Noise parameters dependence on seismic receivers installation conditions was investigated separately. Based on three stations (Makanchi, Borovoye, and Aktyubinsk), spectral density change features are shown after borehole equipment installation. (author)

A study of some economic factors relating to the development and implementation of a satellite power system

Science.gov (United States)

1978-01-01

Areas are examined relating to the design, development and implementation of a satellite power system (SPS): an analysis of the effect of energy R&D programs in general and SPS in particular on optimal fossil fuel consumption patterns, a study of alternative uses of SPS technologies, and a study of the electric power market penetration potential for SPS. It is shown that a credible program of R&D on long-range energy alternatives leads to lower optimal prices for fossil fuels, resulting in large short-term benefits accruing to the specific program elements. Several alternative uses of SPS technologies were identified; however the markets for these technologies are generally quite diffuse and difficult to assess. The notable exception is solar array technology which has, potentially, a very large non-SPS market. It is shown that the market for SPS units derives from two components of demand: the demand created by growth in the electrical energy demand which leads to an increased demand for baseload generating capacity, and a demand created by the need to replace retiring capacity.

KAJIAN ADSORPSI ION LOGAM Cr(VI OLEH ADSORBEN KOMBINASI ARANG AKTIF SEKAM PADI DAN ZEOLIT MENGGUNAKAN METODE SOLID-PHASE SPECTROPHOTOMETRY (SPS

Directory of Open Access Journals (Sweden)

Sulistyo Saputro

2016-10-01

  This study aims to study the use of activated rice husk charcoal and zeolite as combination adsorbents to adsorb Cr(VI metal ions; the effect of the combination adsorbents of activated rice husk charcoal and zeolite’s compositions to adsorb Cr(VI metal ions; and the sensitivity of solid-phase spectrophotometry (SPS as a method to determine the reduced levels of Cr(VI metal ions in the level of 15μ"> g/L. The activated rice husk charcoal used were obtained through the activation process by soaking in a solution of ZnCl2 10% while the zeolite with a solution of H2SO4 10%. The contacting process of the adsorbents with Cr(VI metal ions was done by varying the compositions of the activated rice husk charcoal and zeolite adsorbent, 1:1, 1:2, 1:3, and 2:1. The data analysis of the Cr(VI level used solid-phase spectrophotometry (SPS method. Characterization of activated rice husk charcoal and zeolite used FTIR. The results showed that: (1 a combination of activated rice husk charcoal and zeolite can be used as adsorbent to adsorb Cr(VI metal ions with the adsorption capacity was 0,28 15μ"> g/g; (2 the optimum composition of adsorbents was 1:2 with the percentage of absorption was 40,99%; (3 solid-phase spectrophotometry (SPS is a sensitive method to determine the reduced levels of Cr(VI in the level of 15μ"> g/L with the limit of detection (LOD was 0,021 15μ"> g/L.   Keywords: adsorption, Cr(VI,  activated  rice husk charcoal,  zeolite, solid-phase spectrophotometry

Design Study and Optimization of Irradiation Facilities for Detector and Accelerator Equipment Testing in the SPS North Area at CERN

CERN Document Server

AUTHOR|(CDS)2079748; Stekl, Ivan

Due to increasing performance of LHC during the last years, the strong need of new detector and electronic equipment test areas at CERN appeared from user communities. This thesis reports on two test facilities: GIF++ and H4IRRAD. GIF++, an upgrade of GIF facility, is a combined high-intensity gamma and particle beam irradiation facility for testing detectors for LHC. It combines a high-rate 137Cs source, providing photons with energy of 662 keV, together with the high-energy secondary particle beam from SPS. H4IRRAD is a new mixed-field irradiation area, designed for testing LHC electronic equipment for radiation damage effects. In particular, large volume assemblies such as full electronic racks of high current power converters can be tested. The area uses alternatively an attenuated primary 400 GeV/c proton beam from SPS, or a secondary, mainly proton, beam of 280 GeV/c directed towards a copper target. Different shielding layers are used to reproduce a radiation field similar to the LHC “tunnel” and �...

Results of a beam dump experiment at the CERN SPS neutrino facility

Directory of Open Access Journals (Sweden)

T. Hansl

1978-03-01

Full Text Available We report results from a beam dump experiment that has been performed at the CERN SPS neutrino facility using the CDHS neutrino counter detector. Limits on dimuon and trimuon production by new penetrating neutral particles are given. A new source of prompt electron and muon neutrinos has been observed giving (1.2±0.4× 10−7 νe or νμ per incident proton with neutrino angle smaller than 1.85 mrad and Eν > 20 GeV. If these prompt neutrinos are attributed to charmed meson pair production, the inclusive DD production cross section could be of the order of 30 ωb. If axions are existing their production rate relative to π0 mesons is found to be less than 0.5 × 10−8.

J/$\\psi$ production in proton-nucleus and nucleus-nucleus interactions at the CERN SPS

CERN Document Server

Abreu, M C; Alexa, C; Arnaldi, R; Ataian, M R; Baglin, C; Baldit, A; Bedjidian, Marc; Beolè, S; Boldea, V; Bordalo, P; Borges, G; Bussière, A; Capelli, L; Castanier, C; Castor, J I; Chaurand, B; Chevrot, I; Cheynis, B; Chiavassa, E; Cicalò, C; Claudino, T; Comets, M P; Constans, N; Constantinescu, S; Cortese, P; De Falco, A; De Marco, N; Dellacasa, G; Devaux, A; Dita, S; Drapier, O; Ducroux, L; Espagnon, B; Fargeix, J; Force, P; Gallio, M; Gavrilov, Yu K; Gerschel, C; Giubellino, P; Golubeva, M B; Gonin, M; Grigorian, A A; Grossiord, J Y; Guber, F F; Guichard, A; Gulkanian, H R; Hakobyan, R S; Haroutunian, R; Idzik, M; Jouan, D; Karavitcheva, T L; Kluberg, L; Kurepin, A B; Le Bornec, Y; Lourenço, C; Macciotta, P; MacCormick, M; Marzari-Chiesa, A; Masera, M; Masoni, A; Monteno, M; Musso, A; Petiau, P; Piccotti, A; Pizzi, J R; Prado da Silva, W L; Prino, F; Puddu, G; Quintans, C; Ramello, L; Ramos, S; Rato-Mendes, P; Riccati, L; Romana, A; Santos, H; Saturnini, P; Scalas, E; Scomparin, E; Serci, S; Shahoyan, R; Sigaudo, F; Silva, S; Sitta, M; Sonderegger, P; Tarrago, X; Topilskaya, N S; Usai, G L; Vercellin, Ermanno; Villatte, L; Willis, N

2002-01-01

The NA38 and NA50 experiments at the CERN SPS have measured charmonium production in different colliding systems with the aim of observing a phase transition from ordinary hadronic matter towards a state in which quarks and gluons are deconfined (quark-gluon plasma, QGP). This experimental research is based on the prediction that the J/ psi yield should be suppressed in deconfined matter. The analysis of the data collected by the NA50 experiment with Pb-Pb collisions at 158 GeV/c per nucleon shows that the J/ psi is anomalously suppressed with respect to the pattern observed in proton-nucleus and light ion reactions. (9 refs).

Heat load and deuterium plasma effects on SPS and WSP tungsten

Directory of Open Access Journals (Sweden)

Vilémová Monika

2015-06-01

Full Text Available Tungsten is a prime choice for armor material in future nuclear fusion devices. For the realization of fusion, it is necessary to address issues related to the plasma–armor interactions. In this work, several types of tungsten material were studied, i.e. tungsten prepared by spark plasma sintering (SPS and by water stabilized plasma spraying (WSP technique. An intended surface porosity was created in the samples to model hydrogen/helium bubbles. The samples were subjected to a laser heat loading and a radiation loading of deuterium plasma to simulate edge plasma conditions of a nuclear fusion device (power density of 108 W/cm2 and 107 W/cm2, respectively, in the pulse intervals up to 200 ns. Thermally induced changes in the morphology and the damage to the studied surfaces are described. Possible consequences for the fusion device operation are pointed out.

Transverse momentum spectra of hadrons in p + p collisions at CERN SPS energies from the UrQMD transport model

Science.gov (United States)

Ozvenchuk, V.; Rybicki, A.

2018-05-01

The UrQMD transport model, version 3.4, is used to study the new experimental data on transverse momentum spectra of π±, K±, p and p bar produced in inelastic p + p interactions at SPS energies, recently published by the NA61/SHINE Collaboration. The comparison of model predictions to these new measurements is presented as a function of collision energy for central and forward particle rapidity intervals. In addition, the inverse slope parameters characterizing the transverse momentum distributions are extracted from the predicted spectra and compared to the corresponding values obtained from NA61/SHINE distributions, as a function of particle rapidity and collision energy. A complex pattern of deviations between the experimental data and the UrQMD model emerges. For charged pions, the fair agreement visible at top SPS energies deteriorates with the decreasing energy. For charged K mesons, UrQMD significantly underpredicts positive kaon production at lower beam momenta. It also underpredicts the central rapidity proton yield at top collision energy and overpredicts antiproton production at all considered energies. We conclude that the new experimental data analyzed in this paper still constitute a challenge for the present version of the model.

New ISR and SPS collider multiplicity data and the Golokhvastov generalization of the KNO scaling

International Nuclear Information System (INIS)

Szwed, R.; Wrochna, G.

1985-01-01

The generalization of KNO scaling proposed by Golokhvastov (KNO-G scaling) is tested using pp multiplicity data, in particular results of the new high precision ISR measurements. Since the data obey KNO-G scaling over the full energy range √s=2.51-62.2 GeV with the scaling function psi(z), having only one free parameter, the superiority of the KNO-G over the standard approach is clearly demonstrated. The extrapolation within KNO-G scaling to the SPS Collider energy range and a comparison with the recent UA5 multiplicity results is presented. (orig.)

Differences in high $p_{t}$ meson production between CERN SPS and RHIC heavy ion collisions

CERN Document Server

Papp, G; Barnafoldi, G G; Yi Zhang; Fái, G; Papp, Gabor; Levai, Peter; Barnafoldi, Gergely G.; Zhang, Yi; Fai, George

2001-01-01

In this talk we present a perturbative QCD improved parton model calculation for light meson production in high energy heavy ion collisions. In order to describe the experimental data properly, one needs to augment the standard pQCD model by the transverse momentum distribution of partons ("intrinsic k/sub T/"). Proton-nucleus data indicate the presence of nuclear shadowing and multi-scattering effects. Further corrections are needed in nucleus-nucleus collisions to explain the observed reduction of the cross section. We introduce the idea of proton dissociation and compare our calculations with the SPS and RHIC experimental data. (18 refs).

Sintering of ZrC by hot isostatic pressing (HIP) and spark plasma sintering (SPS). Effect of impurities

International Nuclear Information System (INIS)

Allemand, Alexandre; Le Flem - Dormeval, Marion; Guillard, Francois

2005-01-01

Carbides are generally used as structural materials for high temperature applications. Particularly, ZrC because of low activation, neutronic transparency, cubic structure (isotropic behaviour) and good thermal conductivity, is one of the candidates under consideration for structural materials in the core of new high temperature nuclear reactors (Generation IV). Just a few studies about densification of monolithic ZrC exist. They mainly involve natural sintering or hot pressing at high temperature (until 2700 deg. C). Unfortunately those processes induce grain growth and do not lead to fully densified ZrC. The aim of this study is to compare the characteristics and the properties of ZrC sintered by HIP and by SPS. Fully dense ZrC can be reached either by HIP or by SPS, grain size being more or less controlled. Microstructural observations and mechanical testing of several ZrC grades shows that powder impurities play an important role in the quality of the grain boundaries and consequently in the mechanical properties. In particular, the porosity falls from 17% to 3 % just by reducing the free carbon content in starting ZrC powder. The densification process of dense monolithic ZrC was improved by combining a HIP at 1600 deg. C (titanium canning) followed by a post-HIP at 1900 deg. C (no canning required). Four-point bending tests are in progress to confirm the improvement of fracture strength. (authors)

LAYOUT AND DESIGN OF ELECTROMOBILE CHARGING STATIONS AS URBAN ELEMENTS

Directory of Open Access Journals (Sweden)

Tomáš Chovan

2015-12-01

Full Text Available The contribution is dedicated to the processing of the problems of the insufficient charging for the electric vehicles within the concrete urbanistic centre. It brings a different perspective on the mobility, which is shown in the form of electric energy as the alternative for the needs of urbanization of the cities. It analyses electromobility, new technologies in the field of electric vehicles and the charging stations as the elements of the urbanism. In terms of the solution, the contribution is focused on the Košice city and the location of the public charging stations. Košice do not have sufficient amount of the public charging stations and until the 2014 there was only one public charging station. The contribution is focused on the designing of the parking places with the charging station placed on the appropriate parking places. The resulting design is created in the CAD system, it brings the view of the layout of the charging station at the shopping centre in the open space and in the parking house.

NESSiE: An experimental search for sterile neutrinos with the CERN-SPS beam

International Nuclear Information System (INIS)

Medinaceli, E.

2013-01-01

NESSiE (Neutrino Experiment with SpectrometerS in Europe) is an experiment dedicated to the search for sterile neutrinos beyond the Standard Model with the CERN-SPS neutrino beam. The experiment is based on two identical LAr-TPC's followed by magnetized spectrometers, observing the electron and muon neutrino events at the “Near” (600 m) and “Far” (1300 m) positions from the proton target. The main characteristics of the spectrometers are described here. Spectrometers will exploit a classical dipole magnetic field with iron slabs, and a new concept air-core magnet will perform charge identification and muon momentum measurements in the energy range from ∼100MeV to few GeV over a large transverse area (>50m 2 )

NESSiE: An experimental search for sterile neutrinos with the CERN-SPS beam

Energy Technology Data Exchange (ETDEWEB)

Medinaceli, E., E-mail: medinaceli@pd.infn.it [INFN and University of Padova (Italy)

2013-08-01

NESSiE (Neutrino Experiment with SpectrometerS in Europe) is an experiment dedicated to the search for sterile neutrinos beyond the Standard Model with the CERN-SPS neutrino beam. The experiment is based on two identical LAr-TPC's followed by magnetized spectrometers, observing the electron and muon neutrino events at the “Near” (600 m) and “Far” (1300 m) positions from the proton target. The main characteristics of the spectrometers are described here. Spectrometers will exploit a classical dipole magnetic field with iron slabs, and a new concept air-core magnet will perform charge identification and muon momentum measurements in the energy range from ∼100MeV to few GeV over a large transverse area (>50m{sup 2})

The RTC - a software support system for the control of the CERN SPS

International Nuclear Information System (INIS)

Herr, W.; Lauckner, R.; Morpurga, G.

1989-01-01

The RTC (Run Time Coordinator) is a software support system designed for the SPS control system to provide a runtime environment for application software. It coordinates the execution of individual programs or processes and supervises the process control, i.e. process synchronization, inter process communication, data transfer and operator I/O. This supervision includes the control of processes distributed on a UNIX based network. A standard language independent data interface is part of the system. The system includes tools for data presentation, error logging and contention resolution. This strategy of separating system dependent features from the body of the application programs leads to high flexibility and simplifies the software development. The basic philosophy of the RTC is discussed and its implementation is described. 7 refs

Microprocessor control unit of thyristor regulator of microhydroelectric power station ballast load

International Nuclear Information System (INIS)

Nomokonova, Yu; Bogdanov, E

2014-01-01

The operational principle of microhydroelectric power station ballast load is presented. The comparative overview of the mathematical modeling methods is performed. The ranges of thyristors optimal work are shown as a result of the regulator regimes analysis. Shows the necessity of regulation the ballast load in microhydroelectric power station with help of developed algorithm of the program for microprocessor control

Plant computer system in nuclear power station

International Nuclear Information System (INIS)

Kato, Shinji; Fukuchi, Hiroshi

1991-01-01

In nuclear power stations, centrally concentrated monitoring system has been adopted, and in central control rooms, large quantity of information and operational equipments concentrate, therefore, those become the important place of communication between plants and operators. Further recently, due to the increase of the unit capacity, the strengthening of safety, the problems of man-machine interface and so on, it has become important to concentrate information, to automate machinery and equipment and to simplify them for improving the operational environment, reliability and so on. On the relation of nuclear power stations and computer system, to which attention has been paid recently as the man-machine interface, the example in Tsuruga Power Station, Japan Atomic Power Co. is shown. No.2 plant in the Tsuruga Power Station is a PWR plant with 1160 MWe output, which is a home built standardized plant, accordingly the computer system adopted here is explained. The fundamental concept of the central control board, the process computer system, the design policy, basic system configuration, reliability and maintenance, CRT display, and the computer system for No.1 BWR 357 MW plant are reported. (K.I.)

Sintering, consolidation, reaction and crystal growth by the spark plasma system (SPS)

Energy Technology Data Exchange (ETDEWEB)

Omori, M. [Tohoku Univ., Sendai (Japan). Inst. for Materials Research

2000-08-15

The graphite die set in spark plasma system (SPS) is heated by a pulse direct current. Weak plasma, discharge impact, electric field and electric current, which are based on this current, induce good effects on materials in the die. The surface films of aluminum and pure WC powders are ruptured by the spark plasma. Pure AlN powder is sintered without sintering additives in the electric field. The spark plasma leaves discharge patterns on insulators. Organic fibers are etched by the spark plasma. Thermosetting polyimide is consolidated by the spark plasma. Insoluble polymonomethylsilane is rearranged into the soluble one by the spark plasma. A single crystal of CoSb{sub 3} is grown from the compound powders in the electric field by slow heating. Coupled crystals of eutectic powder are connected with each other in the electric field. (orig.)

Higher brightness beams from the SPS for the HL-LHC era

CERN Document Server

AUTHOR|(CDS)2085448; Bracco, Chiara (CERN)

The need to push the LHC beyond its limits and increase the deliverable luminosity to the experiments by about one order of magnitude has driven the ongoing injector and HL-LHC upgrades. The higher luminosity requires to increase the beam brightness, which directly translates in the need to adapt the different machine protection systems. Among all the foreseen upgrades, the transfer line collimators (TCDI) and the LHC injection protection systems will be revised. In particular, the guaranteed protection is evaluated in this Ph D work, together with the specification for the minimum shielded aperture in case of injection failures. A detailed model is also developed which insures a more reliable and efficient procedure for the validation of the TCDI setup within the required accuracy. The physics beyond colliders will also be pushed over its current limits in the HL-LHC era. SHiP, a new proposed fixed target experiment served by the SPS is under study. The unprecedented level of requested protons on target per ...

A 2006 SPS Summer Intern’s Experiences, Reflections, and Future Ambitions

Science.gov (United States)

Deml, Ann

2006-12-01

As a SPS Summer Intern from the University of Wisconsin-River Falls, I spent nine weeks in the Washington, D.C. area working with the American Physical Society. My work dealt primarily with the development of a ComPADRE outreach website, Physics To Go, which offers the public opportunities to engage in informal physics learning. Specific tasks that I performed included locating content to feature on the homepage, obtaining photographer permissions, and cataloging quality websites into the digital library. At the conclusion of the summer, I accepted an offer to continue working on Physics To Go and have further contributed to its expansion. Participating in this internship has influenced my life in several respects, and as a result, I will be enrolling in a graduate program this coming year. Additionally, I am making plans to participate in a National Student Exchange program and am considering a career with a greater emphasis on research. The internship has served as an invaluable and irreplaceable experience.

Situation and future developments in the power station engineering of the GDR

International Nuclear Information System (INIS)

Effenberger, H.; Weidlich, H.G.

1990-01-01

Starting with the present state of power stations in the GDR and their evaluation in respect of energy and ecology, the authors have developed a concept for the future objectives and possibilities of the power stations. With regard to the modification of the power station engineering, considered as urgently required due to reasons of energy and environment, there was suggestions for modern plant conceptions, such as fluidized bed combustors, combined and gas/steam power plants, besides the retrofitting and the new building of proven conventional plants. It includes also the extension of combined heat and power systems, of nuclear energy, and the use of regenerative energy sources as parts of this concept. The power station modifications intended are shown in tables for the various power station locations. (orig.) [de

Study of problems met in muon pattern recognition for a deep inelastic scattering experiment at the S.P.S

International Nuclear Information System (INIS)

Besson, C.

1976-01-01

The problems of the muon pattern recognition are studied for a muon-proton deep inelastic scattering experiment at the S.P.S. The pattern recognition program is described together with the problems caused by some characteristics of the apparatus of the European muon collaboration. Several reconstruction technics are compared, and a way of handling big drift chamber problems is found. Some results on Monte-Carlo tracks are given [fr

Routine radiation protection precautions in the turbine areas of nuclear power stations of the boiling water reactor type

International Nuclear Information System (INIS)

Meyer, U.; Slavitschek, G.

1978-01-01

The need for limiting access to turbine areas in BWR power stations is pointed out, and the advantages of closed circuit TV, aerosol measurements and lead glass windows are discussed. Reference is made to a 1000 MW station now under construction, a floor plan is shown and the need for making inspection/maintenance access as infrequent as possible is stated. Practical tests with CCTV are shown, and it is reported that attention was paid in the design of the station to achieving good visual contrast in areas which might have to be inspected for leaks. (G.M.E.)

Measurements of quadrupole frequency shift in the SPS at 26 GeV/c

CERN Document Server

Bohl, T; Shaposhnikova, E; Tückmantel, Joachim; CERN. Geneva. AB Department

2008-01-01

Measurements of the quadrupole frequency shift with intensity at 26 GeV/c using the peak detected signal were performed in the SPS from 1999 to monitor the evolution of the low-frequency longitudinal impedance [1]. While the large changes, first, due to the impedance reduction and then due to the re-installation of the MKE kickers,are easy to see, to observe small variations of impedance (as shielding or removal of a few kickers) much higher accuracy of measurements is required. This was difficult to achieve so far, mainly due to the insufficient reproducibility of the longitudinal parameters of the injected beam for different intensities as well as for different MDs. In this Note the important role of longitudinal emittance in addition to the bunch length is also revealed.

Combination of rice husk and coconut shell activated adsorbent to adsorb Pb(II) ionic metal and it’s analysis using solid-phase spectrophotometry (sps)

Science.gov (United States)

Rohmah, D. N.; Saputro, S.; Masykuri, M.; Mahardiani, L.

2018-03-01

The purpose of this research was to know the effect and determine the mass comparation which most effective combination between rice husk and coconut shell activated adsorbent to adsorb Pb (II) ion using SPS method. This research used experimental method. Technique to collecting this datas of this research is carried out by several stages, which are: (1) carbonization of rice husk and coconut shell adsorbent using muffle furnace at a temperature of 350°C for an hour; (2) activation of the rice husk and coconut shell adsorbent using NaOH 1N and ZnCl2 15% activator; (3) contacting the adsorbent of rice husk and coconut shell activated adsorbent with liquid waste simulation of Pb(II) using variation comparison of rice husk and coconut shell, 1:0; 0:1; 1:1; 2:1; 1:2; (4) analysis of Pb(II) using Solid-Phase Spectrophotometry (SPS); (5) characterization of combination rice husk and coconut shell activated adsorbent using FTIR. The result of this research show that the combined effect of combination rice husk and coconut shell activated adsorbent can increase the ability of the adsorbent to absorb Pb(II) ion then the optimum adsorbent mass ratio required for absorbing 20 mL of Pb(II) ion with a concentration of 49.99 µg/L is a ratio of 2:1 with the absorption level of 97,06%Solid-Phase Spectrophotometry (SPS) is an effective method in the level of µg/L, be marked with the Limit of Detection (LOD) of 0.03 µg/L.

A report of two cases of Al-Awadi Raas-Rothschild syndrome (AARRS) supporting that "apparent" Phocomelia differentiates AARRS from Schinzel Phocomelia syndrome (SPS).

Science.gov (United States)

AlQattan, Mohammad M; AlAbdulkareem, Ibrahim; Ballow, Mariam; Al Balwi, Mohammed

2013-09-15

Although there is a long list of syndromes with phocomelia, there are only two syndromes in which there is concurrent pelvic dysplasia and phocomelia: Al-Awadi-Raas-Rothschild syndrome (AARRS) and Schinzel phocomelia syndrome (SPS). Currently, there is a diagnostic confusion between the two syndromes and both have the same MIM entry (MIM 276820). We believe that the two syndromes are different entities and we also believe that the limb defect in SPS is a "true" phocomelia while the limb defect in AARRS is an "apparent" phocomelia. "Apparent" phocomelia describes the most severe form of ulnar ray deficiency in which there is absent ulna with radio-humeral synostosis. "Apparent" phocomelia is diagnosed radiologically by three radiological features: the apparently single bone occupying the arm/forearm appears relatively long, the area of radio-humeral synostosis will have thicker cortex with or without slight angulation, and the lower end of the bone resembles the lower end of a radius and not a humerus. In this paper, we present two new cases of AARRS from two different Saudi Arabian tribes: one case with R292C mutation of WNT7A with bilateral "apparent" phocomelia and a second case with a novel c.814G>T mutation of the WNT7A gene (resulting in wnt7a protein truncation at position 272) with unilateral "apparent" phocomelia. We reviewed previously reported cases of AARRS and SPS to further delineate the differences between these two syndromes. We make the argument that these two syndromes are two different entities and hence require two different MIM entries. Copyright © 2013 Elsevier B.V. All rights reserved.

Enhanced production of low-mass electron-positron pairs in 40-AGeV Pb-Au collisions at the CERN SPS.

Science.gov (United States)

Adamová, D; Agakichiev, G; Appelshäuser, H; Belaga, V; Braun-Munzinger, P; Cherlin, A; Damjanović, S; Dietel, T; Dietrich, L; Drees, A; Esumi, S I; Filimonov, K; Fomenko, K; Fraenkel, Z; Garabatos, C; Glässel, P; Hering, G; Holeczek, J; Kushpil, V; Lenkeit, B; Maas, A; Marín, A; Milosević, J; Milov, A; Miśkowiec, D; Panebrattsev, Yu; Petchenova, O; Petrácek, V; Pfeiffer, A; Rak, J; Ravinovich, I; Rehak, P; Richter, M; Sako, H; Schmitz, W; Sedykh, S; Seipp, W; Sharma, A; Shimansky, S; Slívová, J; Specht, H J; Stachel, J; Sumbera, M; Tilsner, H; Tserruya, I; Wessels, J P; Wienold, T; Windelband, B; Wurm, J P; Xie, W; Yurevich, S; Yurevich, V

2003-07-25

We report on first measurements of low-mass electron-positron pairs in Pb-Au collisions at the CERN SPS beam energy of 40 AGeV. The observed pair yield integrated over the range of invariant masses 0.2e(+)e(-) annihilation with a modified rho propagator. They may be linked to chiral symmetry restoration and support the notion that the in-medium modifications of the rho are more driven by baryon density than by temperature.

Enhanced production of low-mass electron-positron pairs in 40-AGeV Pb-Au collisions at the CERN SPS

CERN Document Server

Adamova, D; Appelshäuser, H; Belaga, V; Braun-Munzinger, P; Cherlin, A; Damjanovic, S; Dietel, T; Dietrich, L; Drees, A; Esumi, S I; Filimonov, K; Fomenko, K; Fraenkel, Zeev; Garabatos, C; Glässel, P; Hering, G; Holeczek, J; Kushpil, V; Lenkeit, B C; Maas, A; Marin, A; Milosevic, J; Milov, A; Miskowiec, D; Panebratsev, Yu A; Petchenova, O Yu; Petracek, V; Pfeiffer, A; Rak, J; Ravinovich, I; Rehak, P; Richter, M; Sako, H; Schmitz, W; Sedykh, S; Seipp, W; Sharma, A; Shimansky, S S; Slivova, J; Specht, H J; Stachel, J; Sumbera, M; Tilsner, H; Tserruya, Itzhak; Wessels, J P; Wienold, T; Windelband, B; Wurm, J P; Xie, W; Yurevich, S; Yurevich, V I

2003-01-01

We report on first measurements of low-mass electron pairs in Pb-Au collisions at the lower SPS beam energy of 40 AGeV. The pair yield integrated over the range of invariant masses 0.2 e+ e- annihilation with a modified rho-propagator. They may be linked to chiral symmetry restoration and support the notion that the in-medium modifications of the rho are more driven by baryon density than by temperature.

Simulation study of electron cloud build up in the SPS MKD kickers

CERN Document Server

Rumolo, G

2009-01-01

During the 2008 run, an unusual behavior characterizing pressure and temperature increase in some of the dump kickers of the SPS was noticed. In particular, it was observed that 1) the MKDV2 kicker would exhibit maximum heating with 75 ns spaced LHC beams and 2) the pressure rise was specially critical in MKDV1 in presence of 50 ns spaced LHC beams [1]. While the anomalous heating of MKDV2 with 75 ns beams could be tentatively explained by the denser beam current spectrum that would more likely hit one of the kicker impedance peaks, the fast pressure rise in MKDV1 with 50 ns spaced beams was ascribed to a surface effect, namely beam induced multipacting leading to electron cloud formation. This report summarizes a simulation study that was done in order to check whether the electron cloud behavior in the dump kickers could explain the experimental observations.

As medidas aplicadas aos acordos SPS e TBT sobre as exportações brasileiras de fumo

Directory of Open Access Journals (Sweden)

Carlos Otávio de Freitas

2015-11-01

Full Text Available O presente estudo tem como objetivo analisar os efeitos das medidas não tarifárias, especificamente as medidas sanitárias e fitossanitárias - SPS e medidas técnicas - TBT, sobre as exportações brasileiras de fumo e se tais efeitos permaneceram nos períodos subsequentes à emissão das notificações. Para tal, foi estimado um modelo gravitacional utilizando uma amostra de 89 países importadores do fumo do Brasil entre o período de 1997 a 2011. O método utilizado na estimação das equações foi o modelo Poisson-Pseudo Maximum Likehood-PPML. Os resultados obtidos mostram que as medidas ou SPS afetaram negativamente o fluxo internacional do comércio de fumo. Além disso, verificou-se que esses efeitos perduraram nos períodos posteriores à emissão da notificação, sendo que as empresas exportadores podem demorar até dois anos para se ajustarem às exigências requeridas. Dentre os objetivos das notificações SPS, a maior parte está relacionada a medidas para proteção da saúde humana e proteção da planta, o que pode explicar a maior dificuldade de adequação, pois são exigências que demandam grandes investimentos. Já as medidas TBT não foram estatisticamente significativas, confirmando o caráter não restritivo dessas notificações sobre o comércio internacional de fumo. Apesar da maior parte das notificações ao fumo estarem associadas a medidas técnicas, os resultados indicaram que elas não configuraram como barreiras ao comércio de fumo. Isso pode sugerir que as exigências a elas referidas, que, em sua grande maioria, foi referente à rotulagem e/ou embalagem, foram atendidas pelo Brasil sem maiores dificuldades. Dessa forma, torna-se importante a inclusão de questões referentes à regulamentação dessas medidas nas discussões e processos de tomada de decisão das empresas exportadoras de fumo. Em termos de ações governamentais, seria interessante a criação ou aperfeiçoamento de políticas no sentido

A joint program for seismographic station operations in the Republic of Kazakstan

International Nuclear Information System (INIS)

Kim, W.Y.; Belyashova, N.N.; Richards, P.G.

1998-01-01

In this paper there are examples of seismic signals recorded at the stations operated jointly by the Kazakhstan National Nuclear Centre and Lamont-Doherty Earth Observatory of Columbia University. Also the way the stations can be used to interpret the natural (earthquake) and and anthropogenic (explosion) sources from which the signals originated is shown. Examples include nuclear explosions carried out by China, India and Pakistan in recent years and months

SPS microwave subsystem potential impacts and benefits. [environmental and societal effects of Solar Power System construction and operation

Science.gov (United States)

Dickinson, R. M.

1978-01-01

The paper examines the possible environmental and societal effects of the construction, installation, and operation of the space end and earth end of the microwave power transmission subsystem that delivers satellite power system (SPS) energy (at about 5 GW per beam) to the power grid on earth. The intervening propagation medium near the earth is also considered. Separate consideration is given to the spacecraft transmitting array, propagation in the ionosphere, and the ground-based rectenna. Radio frequency interference aspects are also discussed.

The new generation of PowerPC VMEbus front end computers for the CERN SPS and LEP accelerators system

OpenAIRE

Charrue, P; Bland, A; Ghinet, F; Ribeiro, P

1995-01-01

The CERN SPS and LEP PowerPC project is aimed at introducing a new generation of PowerPC VMEbus processor modules running the LynxOS real-time operating system. This new generation of front end computers using the state-of-the-art microprocessor technology will first replace the obsolete XENIX PC based systems (about 140 installations) successfully used since 1988 to control the LEP accelerator. The major issues addressed in the scope of this large scale project are the technical specificatio...

Measurement of direct CP-violation with the NA48 experiment at the CERN SPS

CERN Document Server

Blümer, H

1999-01-01

The NA48 experiment at the CERN SPS uses simultaneous, nearly collinear beams of long-lived and short-lived neutral kaons to measure the direct CP-violation parameter epsilon '/ epsilon using the double ratio method to an overall accuracy of 2.10/sup -4/, three times better than previous results. The detector has been installed and commissioned in 1995 and 1996. First physics data were recorded during 42 days in fall 1997 yielding more events than the previous experiment NA31. The talk presents the apparatus performance, data quality, the current status of the physics analysis and ongoing activities. The experiment has performed another data run from May to September 1998, which has given a substantial increase in statistics. (11 refs).

Sanitary and phytosanitary legislation in the Russian Federation: a general overview in light of the WTO SPS Agreement and EU principles of food safety / Irina Kireeva, Robert Black

Index Scriptorium Estoniae

Kireeva, Irina

2010-01-01

Maailma Kaubandusorganisatsiooni (WTO) eeskirjadest sanitaar-ja fütosanitaarmeetmete (SPS) kohta ja Euroopa Liidu vastavate õigusaktidest. Pestitsiidide ja põllumajanduskemikaalide tehnilistest normidest. Sanitaar- ja fütosanitaarmeetmete rakendamise lepingust (1995)

Service offerings and interfaces for the ACTS network of earth stations

Science.gov (United States)

Coney, T. A.; Dobyns, T. R.; Chitre, D. M.; Lindstrom, R.

1988-01-01

The NASA Advanced Communications Technology Satellite (ACTS) will use a network of about 20 earth stations to operate as a Mode 1 network. This network will support two ACTS program objectives: to verify the technical performance of ACTS Mode 1 operation in GEO and to demonstrate the types and quality of services that can be provided by an ACTS Mode 1 communications system. The terrestrial interface design is a critical element in assuring that these network earth stations will meet the objectives. In this paper, the applicable terrestrial interface design requirements, the resulting interface specifications, and the associated terrestrial input/output hardware are discussed. A functional block diagram of a network earth station is shown.

Optimizing of SPS pressed SrFe12O19 pellets from nano-powder

DEFF Research Database (Denmark)

Mortensen, Anna; Stingaciu, Marian; Christensen, Mogens

2015-01-01

direction giving a higher net magnetization. One challenge is to optimize the pressing conditions in order to maximize the remanence and thus the energy product. In present work the SrFe12O19 powder was made in an autoclave and was analysed by X-ray diffraction and Rietveld Refinement to determine particle...... size. The powder was pressed using Spark Plasma Syntering (SPS) system at different conditions in order to investigate how the pressing conditions influence the magnetic properties. It was found, that pressing at 950oC leads to a much better alignment than pellets pressed at room temperature....... Furthermore, ball milling seems to decrease the degree of alignment and thereby the magnetic remanence which leads to a lower energy product. The magnetization was characterized using Vibrating Sample Magnetometer. By applying an external magnetic field before pressing, the alignment is heightened...

Azimuthal anisotropies and initial-state fluctuations from SPS to LHC energies

CERN Document Server

Milosevic, Jovan

2016-01-01

The $v_{3}$ coefficient, obtained using the PbAu data from the CERES detector at the top SPS energy, is presented. The $v_{2}$ is measured over a $p_{T}$ range up to 100 GeV/c in PbPb collisions collected with the CMS detector. The $v_{2}\\{2\\}$ of charged and strange particles emitted in pp collisions shows a mass ordering effect. The $v_{2}\\{4\\}$ and $v_{2}\\{6\\}$ are comparable to the $v_{2}\\{2\\}$, and thus supports the collective nature of the long-range correlations in high-multiplicity pp collisions at 13~TeV. Principle Component Analysis (PCA) of two-particle harmonics ($V_{n\\Delta}$) is studied in PbPb and high-multiplicity pPb collisions at the LHC. The factorization breaking of the $V_{n\\Delta}$ can be attributed to the effect of initial-state fluctuations (ISF). Using a PCA, the $V_{n\\Delta}$ are characterized through the leading and sub-leading modes. The leading modes are essentially equivalent to the $v_{n}\\{2\\}$. The sub-leading modes represent the largest sources of factorization breaking.

Assessment of thermal loads in the CERN SPS crab cavities cryomodule1

Science.gov (United States)

Carra, F.; Apeland, J.; Calaga, R.; Capatina, O.; Capelli, T.; Verdú-Andrés, S.; Zanoni, C.

2017-07-01

As a part of the HL-LHC upgrade, a cryomodule is designed to host two crab cavities for a first test with protons in the SPS machine. The evaluation of the cryomodule heat loads is essential to dimension the cryogenic infrastructure of the system. The current design features two cryogenic circuits. The first circuit adopts superfluid helium at 2 K to maintain the cavities in the superconducting state. The second circuit, based on helium gas at a temperature between 50 K and 70 K, is connected to the thermal screen, also serving as heat intercept for all the interfaces between the cold mass and the external environment. An overview of the heat loads to both circuits, and the combined numerical and analytical estimations, is presented. The heat load of each element is detailed for the static and dynamic scenarios, with considerations on the design choices for the thermal optimization of the most critical components.

Centrifugal Compressor Unit-based Heat Energy Recovery at Compressor Stations

Directory of Open Access Journals (Sweden)

V. S. Shadrin

2016-01-01

Full Text Available About 95% of the electricity consumed by air compressor stations around the world, is transformed into thermal energy, which is making its considerable contribution to global warming. The present article dwells on the re-use (recovery of energy expended for air compression.The article presents the energy analysis of the process of compressing air from the point of view of compressor drive energy conversion into heat energy. The temperature level of excess heat energy has been estimated in terms of a potential to find the ways of recovery of generated heat. It is shown that the temperature level formed by thermal energy depends on the degree of air compression and the number of stages of the compressor.Analysis of technical characteristics of modern equipment from leading manufacturers, as well as projects of the latest air compressor stations have shown that there are two directions for the recovery of heat energy arising from the air compression: Resolving technological problems of compressor units. The use of the excess heat generation to meet the technology objectives of the enterprise. This article examines the schematic diagrams of compressor units to implement the idea of heat recovery compression to solve technological problems: Heating of the air in the suction line during operation of the compressor station in winter conditions. Using compression heat to regenerate the adsorbent in the dryer of compressed air.The article gives an equity assessment of considered solutions in the total amount of heat energy of compressor station. Presented in the present work, the analysis aims to outline the main vectors of technological solutions that reduce negative impacts of heat generation of compressor stations on the environment and creating the potential for reuse of energy, i.e. its recovery.

BATCH ANAEROBIC TREATMENT OF FRESH LEACHATE FROM TRANSFER STATION

Directory of Open Access Journals (Sweden)

SEYED MOHAMMAD DARA GHASIMI

2008-12-01

Full Text Available Leachate from transfer station requires treatment before being discharged into the environment to avoid surface and underground water contamination. Various factors such as waste composition, availability of oxygen and moisture, designing and controlling of transfer station operations have been shown to affect the composition of the leachate. The high COD, BOD, ammonia nitrogen (NH3-N and heavy metals contents of fresh leachate are the main problems faced by leachate treatment operators. The result of the present study indicated that this process reduced the COD content by 43%.The average removal efficiencies of BOD5, TS, TSS, and VSS were 80, 49, 37 and 39 %, respectively.

The new generation of PowerPC VMEbus front end computers for the CERN SPS and LEP accelerators control system

OpenAIRE

Van den Eynden, M

1995-01-01

The CERN SPS and LEP PowerPC project is aimed at introducing a new generation of PowerPC VMEbus processor modules running the LynxOS real-time operating system. This new generation of front end computers using the state-of-the-art microprocessor technology will first replace the obsolete Xenix PC based systems (about 140 installations) successfully used since 1988 to control the LEP accelerator. The major issues addressed in the scope of this large scale project are the technical specificatio...

Valves for condenser-cooling-water circulating piping in thermal power station and nuclear power station

International Nuclear Information System (INIS)

Kondo, Sumio

1977-01-01

Sea water is mostly used as condenser cooling water in thermal and nuclear power stations in Japan. The quantity of cooling water is 6 to 7 t/sec per 100,000 kW output in nuclear power stations, and 3 to 4 t/sec in thermal power stations. The pipe diameter is 900 to 2,700 mm for the power output of 75,000 to 1,100,000 kW. The valves used are mostly butterfly valves, and the reliability, economy and maintainability must be examined sufficiently because of their important role. The construction, number and arrangement of the valves around a condenser are different according to the types of a turbine and the condenser and reverse flow washing method. Three types are illustrated. The valves for sea water are subjected to the electrochemical corrosion due to sea water, the local corrosion due to stagnant water, the fouling by marine organisms, the cavitation due to valve operation, and the erosion by earth and sand. The fundamental construction, use and features of butterfly valves are described. The cases of the failure and repair of the valves after their delivery are shown, and they are the corrosion of valve bodies and valve seats, and the separation of coating and lining. The newly developed butterfly valve with overall water-tight rubber lining is introduced. (Kako, I.)

Compilation and assessment of microwave bioeffects. Final report. A selective review of the literature on biological effects of microwaves in relation to the Satellite Power System (SPS)

Energy Technology Data Exchange (ETDEWEB)

Justesen, D.R.; Ragan, H.A.; Rogers, L.E.; Guy, A.W.; Hjeresen, D.L.; Hinds, W.T.; Phillips, R.D.

1978-05-01

One of many alternate sources of electrical energy that are being considered by the Department of Energy is a microwave-mediated Satellite Power System (SPS). Once inserted into geosynchronous orbit at an altitude of more than 40,000 kilometers, a satellite would collect then convert the sun's energy to 2450-MHz microwaves, which would be beamed to the Earth's surface, where a rectifying antenna (rectenna) would convert the microwaves to electrical current suitable for industrial and domestic use. The expanse of each rectenna (about 10 by 13 kilometers), the power density of the continuous-wave microwave beam (approx. 23 mW/cm/sup 2/ at center, with fall off to 1 mW/cm/sup 2/ or less at the periphery of the rectenna), and the possibility that 20 or more satellite systems will eventually be operating, creates two sets of interrelated problems for biological/ecological assessment. These are 1) the effects of microwave fields of higher intensity on airborne biota (including human beings in aircraft) that may traffic the area above the rectenna and 2) the effects of virtually perpetual fields of much lower intensity on all forms of life at and beyond the rectennae's zone of exclusion. In this review, the scientific literature is examined, not only for biological effects that are pertinent to assessment of SPS, but for hiatuses of knowledge that will have to be filled before SPS can be vouched for operational safety.

Static stability characteristics of the boilers at Oldbury nuclear power station

International Nuclear Information System (INIS)

Paynter, R.J.; Rea, J.

1986-01-01

The cause of an intermittent load loss at Oldbury Nuclear Power Station is shown to be the high sensitivity of boiler performance to the imposed spatial distribution of boiler gas inlet temperature. This high sensitivity is demonstrated to be a function of the inherent static stability characteristics of the boilers. The installation of orifice plates with a high flow resistance into the feed pipework to the half boilers has greatly reduced the boiler sensitivity and eliminated the intermittent load loss so that, on average, higher electrical generation is obtained from the station. (author)

Toward quantification of the uncertainty in estimating frequency of critical station blackout

International Nuclear Information System (INIS)

Rodgers, Shawn; Betancourt, Coral; Kee, Ernie; Nelson, Paul; Rodi, Paul

2011-01-01

A formal statement of the critical station blackout problem is provided, and a solution given, up to evaluation of an n-dimensional 'non recovery integral' n =number of trains (parallel backup sources of electrical power). Several approaches that have been developed in the industry to estimate probability of critical station blackout are shown to be interpretable as special cases of such integrals. Computational results, for a simple model problem, suggest there is yet a very substantial over conservatism in current state-of-the-art techniques for estimating probability of critical station blackout. Research issues associated to possibly meeting this need via computational evaluation of the non recovery integral are discussed. (author)

Space Station Freedom pressurized element interior design process

Science.gov (United States)

Hopson, George D.; Aaron, John; Grant, Richard L.

1990-01-01

The process used to develop the on-orbit working and living environment of the Space Station Freedom has some very unique constraints and conditions to satisfy. The goal is to provide maximum efficiency and utilization of the available space, in on-orbit, zero G conditions that establishes a comfortable, productive, and safe working environment for the crew. The Space Station Freedom on-orbit living and working space can be divided into support for three major functions: (1) operations, maintenance, and management of the station; (2) conduct of experiments, both directly in the laboratories and remotely for experiments outside the pressurized environment; and (3) crew related functions for food preparation, housekeeping, storage, personal hygiene, health maintenance, zero G environment conditioning, and individual privacy, and rest. The process used to implement these functions, the major requirements driving the design, unique considerations and constraints that influence the design, and summaries of the analysis performed to establish the current configurations are described. Sketches and pictures showing the layout and internal arrangement of the Nodes, U.S. Laboratory and Habitation modules identify the current design relationships of the common and unique station housekeeping subsystems. The crew facilities, work stations, food preparation and eating areas (galley and wardroom), and exercise/health maintenance configurations, waste management and personal hygiene area configuration are shown. U.S. Laboratory experiment facilities and maintenance work areas planned to support the wide variety and mixtures of life science and materials processing payloads are described.

Equipment and detectors calibration behind shielding of CERN high-energy particle accelerator SPS: June 2007

International Nuclear Information System (INIS)

Spurny, Frantisek; Ploc, Ondrej

2008-02-01

High energy stray radiation fields have been realised since 1993 at CERN also in the frame of CEC-CERN collaboration on the project: 'Detection and the Dosimetry of Neutrons and Charged Particles at Aviation Altitudes in the Earth's Atmosphere'. They are formed at the H6 beam of the north experimental area of the SPS facility. Two shielding configurations have been built, with the top concrete, resp. top iron shielding. Many intercalibration experiments have been realised since the beginning. After an interruption due to technical problems, two other campaigns have been realised during 2006 year, another one during the June 2007. This report describes analyses and discusses the most of results obtained during the last, 2007 run.. (author)

Design principles for target stations and methods of remote handling at PSI

International Nuclear Information System (INIS)

Steiner, E.W.

1992-01-01

Two design concepts for target stations used at Paul Scherrer Institute (PSI) are shown. The method of the remote handling of activated elements is described and some conclusions with respect to a radioactive beam facility are given

Digital Signal Processing Applications and Implementation for Accelerators Digital Notch Filter with Programmable Delay and Betatron Phase Adjustment for the PS, SPS and LHC Transverse Dampers

CERN Document Server

Rossi, V

2002-01-01

In the framework of the LHC project and the modifications of the SPS as its injector, I present the concept of global digital signal processing applied to a particle accelerator, using Field Programmable Gate Array (FPGA) technology. The approach of global digital synthesis implements in numerical form the architecture of a system, from the start up of a project and the very beginning of the signal flow. It takes into account both the known parameters and the future evolution, whenever possible. Due to the increased performance requirements of today's projects, the CAE design methodology becomes more and more necessary to handle successfully the added complexity and speed of modern electronic circuits. Simulation is performed both for behavioural analysis, to ensure conformity to functional requirements, and for time signal analysis (speed requirements). The digital notch filter with programmable delay for the SPS Transverse Damper is now fully operational with fixed target and LHC-type beams circulating in t...

Status and plans of the ion program of NA61 at the CERN SPS

CERN Document Server

Grebieszkow, Katarzyna

2012-01-01

The NA61/SHINE at the CERN SPS is a new experiment to study hadron production in h+h, h+A and A+A interactions. The main goal of the NA61 ion program is to explore the phase diagram (T - mu_B) of strongly interacting matter. In particular, we plan to study the properties of the onset of deconfinement and to search for the signatures of the critical point. A two-dimensional scan of the phase diagram will be performed by varying the energy (13A-158A GeV) and system size (p+p, Be+Be, Ar+Ca, Xe+La) of collisions. This paper summarizes the status and plans of the NA61/SHINE ion program. In particular the detector upgrades, data taking schedule and the first results on spectra and correlations are discussed.

Technical Analysis of the Hydrogen Energy Station Concept, Phase I and Phase II

Energy Technology Data Exchange (ETDEWEB)

TIAX, LLC

2005-05-04

patterns would be most viable for an energy station, TIAX developed several criteria for selecting a representative set of technology configurations. TIAX applied these criteria to all possible technology configurations to determine an optimized set for further analysis, as shown in Table ES-1. This analysis also considered potential energy station operational scenarios and their impact upon hydrogen and power production. For example, an energy station with a 50-kWe reformer could generate enough hydrogen to serve up to 12 vehicles/day (at 5 kg/fill) or generate up to 1,200 kWh/day, as shown in Figure ES-1. Buildings that would be well suited for an energy station would utilize both the thermal and electrical output of the station. Optimizing the generation and utilization of thermal energy, hydrogen, and electricity requires a detailed look at the energy transfer within the energy station and the transfer between the station and nearby facilities. TIAX selected the Baseline configuration given in Table ES-1 for an initial analysis of the energy and mass transfer expected from an operating energy station. Phase II The purpose of this technical analysis was to analyze the development of a hydrogen-dispensing infrastructure for transportation applications through the installation of a 50-75 kW stationary fuel cell-based energy station at federal building sites. The various scenarios, costs, designs and impacts of such a station were quantified for a hypothetical cost-shared program that utilizes a natural gas reformer to provide hydrogen fuel for both the stack(s) and a limited number of fuel cell powered vehicles, with the possibility of using cogeneration to support the building heat load.

The synthesis of corncobs (zea mays) active charcoal and water hyacinth (eichornia crassipes) adsorbent to adsorb Pb(II) with it’s analysis using solid-phase spectrophotometry (sps)

Science.gov (United States)

Saputro, S.; Masykuri, M.; Mahardiani, L.; Kurniastuti, D.

2018-03-01

This research aim to examine the effect of the combination between corncobs and water hyacinth to adsorb lead (II), the most effective combination have determined by compared the ratio of corncobs adsorbent and water hyacinth to the increasing adsorption of the Pb(II), prove the effectiveness of the solid-phase spectrophotometry (sps) to determine the levels of Pb(II) as the result of the corncobs active charcoal adsorption and water hyacinth in the level of µg/L. The research method used is experimental method. The data collecting technique is carried out by several stages, which are carbonization using muffle furnace at a temperature of 350°C for 1.5 hours, activation of the corncobs charcoal and water hyacinth using HCl 1M and HCl 5M activator, contacting the adsorbent of corncobs active charcoal and water hyacinth with liquid waste simulation of Pb(II) using variation of corncobns and water hyacinth, 1:0; 0:1; 1:1; 2:1; 1:2, analysis of Pb(II) using an sps, characterization of corncobs active charcoal adsorbent and water hyacinth using FTIR. Research results show that the combined effect of activated charcoal corncobs and water hyacinth can increase the ability of the adsorbent to absorb Pb(II), the optimum adsorbent mass ratio of 1:1 with the absorption level of 90.33%, SPS is an effective method to analyze the decreasing level of Pb(II) as the adsorbtion result of the corncobs active charcoal and water hyacinth in the level of µg/L, with the limit of detection (LOD) of 0.06 µg/L.

Multifractal characteristics of multiparticle production in heavy-ion collisions at SPS energies

Science.gov (United States)

Khan, Shaista; Ahmad, Shakeel

Entropy, dimensions and other multifractal characteristics of multiplicity distributions of relativistic charged hadrons produced in ion-ion collisions at SPS energies are investigated. The analysis of the experimental data is carried out in terms of phase space bin-size dependence of multiplicity distributions following the Takagi’s approach. Yet another method is also followed to study the multifractality which, is not related to the bin-width and (or) the detector resolution, rather involves multiplicity distribution of charged particles in full phase space in terms of information entropy and its generalization, Rényi’s order-q information entropy. The findings reveal the presence of multifractal structure — a remarkable property of the fluctuations. Nearly constant values of multifractal specific heat “c” estimated by the two different methods of analysis followed indicate that the parameter “c” may be used as a universal characteristic of the particle production in high energy collisions. The results obtained from the analysis of the experimental data agree well with the predictions of Monte Carlo model AMPT.

UA9 Results from Crystal Collimation Tests in the SPS & Future Strategy

CERN Document Server

Scandale, W

2013-01-01

The UA9 Collaboration, with support by EuCARD-AccNet, is investigating how bent crystals, used as primary collimators, could assist and improve the collimation process in modern hadron colliders like the LHC. From 2009 onwards the UA9 Collaboration has successfully tested silicon crystals at the SPS, performing measurements of the associated collimation efficiency by means of various methods and detectors. This report presents the main UA9 results, obtained with protons and Pb ions at 120 GeV/c and 270 GeV/c per charge from 2009 to 2012, which indicate that crystal assisted collimation is well mastered and understood. Specifically, reduced loss rates were demonstrated close to the crystal, as well as in a downstream off-momentum region, and, indeed, all around the ring. In addition, the importance of the crystal miscut angle was elucidated and a first industrial goniometer compliant with LHC specifications has become available. At the end of the report, the near-term plan for LHC crystal collimation is descri...

NA61/SHINE facility at the CERN SPS: beams and detector system

CERN Document Server

Abgrall, N.; Aduszkiewicz, A.; Ali, Y.; Anticic, T.; Antoniou, N.; Baatar, B.; Bay, F.; Blondel, A.; Blumer, J.; Bogomilov, M.; Bogusz, M.; Bravar, A.; Brzychczyk, J.; Bunyatov, S.A.; Christakoglou, P.; Czopowicz, T.; Davis, N.; Debieux, S.; Dembinski, H.; Diakonos, F.; Di Luise, S.; Dominik, W.; Drozhzhova, T.; Dumarchez, J.; Dynowski, K.; Engel, R.; Efthymiopoulos, I.; Ereditato, A.; Fabich, A.; Feofilov, G.A.; Fodor, Z.; Fulop, A.; Gazdzicki, M.; Golubeva, M.; Grebieszkow, K.; Grzeszczuk, A.; Guber, F.; Haesler, A.; Hasegawa, T.; Hierholzer, M.; Idczak, R.; Igolkin, S.; Ivashkin, A.; Jokovic, D.; Kadija, K.; Kapoyannis, A.; Kaptur, E.; Kielczewska, D.; Kirejczyk, M.; Kisiel, J.; Kiss, T.; Kleinfelder, S.; Kobayashi, T.; Kolesnikov, V.I.; Kolev, D.; Kondratiev, V.P.; Korzenev, A.; Koversarski, P.; Kowalski, S.; Krasnoperov, A.; Kurepin, A.; Larsen, D.; Laszlo, A.; Lyubushkin, V.V.; Maćkowiak-Pawlowska, M.; Majka, Z.; Maksiak, B.; Malakhov, A.I.; Maletic, D.; Manglunki, D.; Manic, D.; Marchionni, A.; Marcinek, A.; Marin, V.; Marton, K.; Mathes, H.J; Matulewicz, T.; Matveev, V.; Melkumov, G.L.; Messina, M.; Mrówczyński, St.; Murphy, S.; Nakadaira, T.; Nirkko, M.; Nishikawa, K.; Palczewski, T.; Palla, G.; Panagiotou, A.D.; Paul, T.; Peryt, W.; Petukhov, O.; Pistillo, C.; Planeta, R.; Pluta, J.; Popov, B.A.; Posiadala, M.; Puławski, S.; Puzovic, J.; Rauch, W.; Ravonel, M.; Redij, A.; Renfordt, R.; Richter-Was, E.; Robert, A.; Röhrich, D.; Rondio, E.; Rossi, B.; Roth, M.; Rubbia, A.; Rustamov, A.; Rybczyński, M.; Sadovsky, A.; Sakashita, K.; Savic, M.; Schmidt, K.; Sekiguchi, T.; Seyboth, P.; Sgalaberna, D.; Shibata, M.; Sipos, R.; Skrzypczak, E.; Słodkowski, M.; Sosin, Z.; Staszel, P.; Stefanek, G.; Stepaniak, J.; Stroebele, H.; Susa, T.; Szuba, M.; Tada, M.; Tereshchenko, V.; Tolyhi, T.; Tsenov, R.; Turko, L.; Ulrich, R.; Unger, M.; Vassiliou, M.; Veberic, D.; Vechernin, V.V.; Vesztergombi, G.; Vinogradov, L.; Wilczek, A.; Włodarczyk, Z.; Wojtaszek-Szwarz, A.; Wyszyński, O.; Zambelli, L.; Zipper, W.

2014-01-01

NA61/SHINE (SPS Heavy Ion and Neutrino Experiment) is a multi-purpose experimental facility to study hadron production in hadron-proton, hadron-nucleus and nucleus-nucleus collisions at the CERN Super Proton Synchrotron. It recorded the first physics data with hadron beams in 2009 and with ion beams (secondary 7Be beams) in 2011. NA61/SHINE has greatly profited from the long development of the CERN proton and ion sources and the accelerator chain as well as the H2 beamline of the CERN North Area. The latter has recently been modified to also serve as a fragment separator as needed to produce the Be beams for NA61/SHINE. Numerous components of the NA61/SHINE set-up were inherited from its predecessors, in particular, the last one, the NA49 experiment. Important new detectors and upgrades of the legacy equipment were introduced by the NA61/SHINE Collaboration. This paper describes the state of the NA61/SHINE facility - the beams and the detector system - before the CERN Long Shutdown I, which started in March ...

Improved correlation of monthly mean daily and hourly diffuse radiation with the corresponding global radiation for Indian stations

International Nuclear Information System (INIS)

Garg, H.P.; Garg, S.N.

1985-12-01

Several existing correlations between radiation monthly mean ratios of global to extraterrestrial and diffuse to global were tried for four Indian stations and found inadequate. New correlations were established for these stations and it was shown that these correlations are highly climate dependent. Classical equation of Liu and Jordon was tried to find hourly diffuse and global radiation from daily sums of diffuse and global radiation respectively. It was suitably modified to suit the Indian data. Equations developed by Collares-Pereira and Rabl have shown excellent agreement with the observed values

Space Station Freedom - Configuration management approach to supporting concurrent engineering and total quality management. [for NASA Space Station Freedom Program

Science.gov (United States)

Gavert, Raymond B.

1990-01-01

Some experiences of NASA configuration management in providing concurrent engineering support to the Space Station Freedom program for the achievement of life cycle benefits and total quality are discussed. Three change decision experiences involving tracing requirements and automated information systems of the electrical power system are described. The potential benefits of concurrent engineering and total quality management include improved operational effectiveness, reduced logistics and support requirements, prevention of schedule slippages, and life cycle cost savings. It is shown how configuration management can influence the benefits attained through disciplined approaches and innovations that compel consideration of all the technical elements of engineering and quality factors that apply to the program development, transition to operations and in operations. Configuration management experiences involving the Space Station program's tiered management structure, the work package contractors, international partners, and the participating NASA centers are discussed.

Determination of Pb2+ metal ion level in liquid waste from adsorption process by combination adsorbent of rice husk and water hyacinth charcoal using solid-phase spectrophotometry (sps)

Science.gov (United States)

Saputro, S.; Masykuri, M.; Mahardiani, L.; Hidayah, AN

2018-03-01

This research are to find out the influence of adsorbent composition between rice husk and water hyacinth in decreasing of Pb2+ ion in simulation liquid waste; the optimumcomposition of combination adsorbent of rice husk and water hyacinth charcoal on Pb2+ ion adsorption; and theeffectivenessof SPS as a method to determine the decreasing level of Pb2+ ion in simulation liquid waste by combination adsorbent of rice husk and water hyacinth charcoal in µg/L level. Rice husk and water hyacinth carbonization using muffle furnace at 350°C for 1 hour. Rice husk charcoal activation in a 2 N NaOH solution and water hyacinth charcoal activated in a 5 M HCl solution. Contacting the combination adsorbent of rice husk and water hyacinth charcoal with a Pb2+ solution with variation of mass composition, 1:0 ; 0:1 ; 1:1 ; 1:2 and 2:1. Analysis of the Pb2+ ion level using SPS method. Characterization of rice husk and water hyacinth charcoal using the FTIR. The results showed that the combination adsorbent composition of rice husk and water hyacinth charcoal have an impact on decreasing Pb2+ ion level. The optimum composition of combination adsorbent of rice husk and water hyacinth charcoal on the adsorption Pb2+ ion is 1:2. SPS is an effective method to determine the decreasing Pb2+ ion in simulation liquid waste from the adsorption process by combination adsorbent of rice husk and water hyacinth in µg/L, with Limit of Detection (LOD) was 0,06 µg/L.

Cost comparison of 4x500 MW coal-fuelled and 4x850 MW CANDU nuclear generating stations

International Nuclear Information System (INIS)

Costa, M.

1981-01-01

The lifetime costs for a 4x850 MW CANDU generating station are compared to those for 4x500 MW bituminous coal-fuelled generating stations. Two types of coal-fuelled stations are considered; one burning U.S. coal which includes flue gas desulfurization and one burning Western Canadian coal. Current estimates for the capital costs, operation and maintenance costs, fuel costs, decommissioning costs and irradiated fuel management costs are shown. The results show: (1) The accumulated discounted costs of nuclear generation, although initially higher, are lower than coal-fuelled generation after two or three years. (2) Fuel costs provide the major contribution to the total lifetime costs for coal-fuelled stations whereas capital costs are the major item for the nuclear station. (3) The break even lifetime capacity factor between nuclear and U.S. coal-fuelled generation is projected to be 5%; that for nuclear and Canadian coal-fuelled generation is projected to be 9%. (4) Large variations in the costs are required before the cost advantage of nuclear generation is lost. (5) Comparison with previous results shows that the nuclear alternative has a greater cost advantage in the current assessment. (6) The total unit energy cost remains approximately constant throughout the station life for nuclear generation while that for coal-fuelled generation increases significantly due to escalating fuel costs. The 1978 and 1979 actual total unit energy cost to the consumer for several Ontario Hydro stations are detailed, and projected total unit energy costs for several Ontario Hydro stations are shown in terms of escalated dollars and in 1980 constant dollars

Rating curve estimation using Envisat virtual stations on the main Orinoco river

Directory of Open Access Journals (Sweden)

Juan León

2011-09-01

Full Text Available Rating curve estimation (height-stream relation made by hydrometric stations representing cross-sections of a river is one of hydrometrics’ fundamental tasks due to the fact that it leads to deducing a river’s average daily flow on that particular section. This information is fundamental in any attempt at hydrological modelling. However, the number of hydrological control stations monitoring large hydrological basins has been reduced worldwide. Space hydrology studies during the last five years have shown that satellite radar altimetry means that hydrological monitoring networks’ available information can be densified due to the introduction of so-called virtual stations and the joint use of such information along with in-situ measured flow records for estimating expenditure curves at these stations. This study presents the rating curves for 4 Envisat virtual stations located on the main stream of the Orinoco River. Virtual stations’ flows were estimated by using the Muskingum- Cunge 1D model. There was less than 1% error between measured and estimated flows. The methodology led to reducing average zero flow depth; in this case, it led to depths ranging from 11 to 20 meters being found along the 130 km of the Orinoco River represented by the virtual stations being considered.

System control fuzzy neural sewage pumping stations using genetic algorithms

Directory of Open Access Journals (Sweden)

Владлен Николаевич Кузнецов

2015-06-01

Full Text Available It is considered the system of management of sewage pumping station with regulators based on a neuron network with fuzzy logic. Linguistic rules for the controller based on fuzzy logic, maintaining the level of effluent in the receiving tank within the prescribed limits are developed. The use of genetic algorithms for neuron network training is shown.

Simulation and virtual reality in medical education and therapy: a protocol.

Science.gov (United States)

Roy, Michael J; Sticha, Deborah L; Kraus, Patricia L; Olsen, Dale E

2006-04-01

Continuing medical education has historically been provided primarily by didactic lectures, though adult learners prefer experiential or self-directed learning. Young physicians have extensive experience with computer-based or "video" games, priming them for medical education--and treating their patients--via new technologies. We report our use of standardized patients (SPs) to educate physicians on the diagnosis and treatment of biological and chemical warfare agent exposure. We trained professional actors to serve as SPs representing exposure to biological agents such as anthrax and smallpox. We rotated workshop participants through teaching stations to interview, examine, diagnose and treat SPs. We also trained SPs to simulate a chemical mass casualty (MASCAL) incident. Workshop participants worked together to treat MASCAL victims, followed by discussion of key teaching points. More recently, we developed computer-based simulation (CBS) modules of patients exposed to biological agents. We compare the strengths and weaknesses of CBS vs. live SPs. Finally, we detail plans for a randomized controlled trial to assess the efficacy of virtual reality (VR) exposure therapy compared to pharmacotherapy for post-traumatic stress disorder (PTSD). PTSD is associated with significant disability and healthcare costs, which may be ameliorated by the identification of more effective therapy.

Improved monolithic reinforced concrete construction for nuclear power stations

International Nuclear Information System (INIS)

Guenther, P.; Fischer, K.

1983-01-01

Experience has shown that in applying monolithic reinforced concrete in nuclear power plant construction the following auxiliary means are useful: measuring sheets in assembling, welding gauges for reaching high tolerance accuracies of prefabricated reinforced concrete members, suitable lining materials, formwork anchorage and formwork release agents, concrete workability agents, mechanized procedures for finishing and assembling. These means were successfully tested in constructing the Greifswald nuclear power station

Principal facts for about 16,000 gravity stations in the Nevada Test Site and vicinity

International Nuclear Information System (INIS)

Harris, R.N.; Ponce, D.A.; Oliver, H.W.; Healey, D.L.

1989-01-01

The Nevada Test Site (NTS) and vicinity includes portions of the Goldfield, Caliente, Death Valley, and Las Vegas. This report documents and consolidates previously published and recently compiled gravity data to establish a gravity data base of about 16,000 stations for the NTS and vicinity. While compiling data sets, redundant stations and stations having doubtful locations or gravity values were excluded. Details of compiling the gravity data sets are discussed in later sections. Where feasible, an accuracy code has been assigned to each station so that the accuracy or reliability of each station can be evaluated. This data base was used in preparing complete Bouguer and isostatic gravity maps of the NTS and vicinity. Since publication of the complete Bouguer gravity map, additional data were incorporated into the isostatic gravity map. Gravity data were compiled from five sources: 14,183 stations from the US Geological Survey (USGS), 326 stations from Exploration Data Consultants (EDCON) of Denver, Colorado, 906 stations from the Los Alamos National Laboratory (LANL), 212 stations from the University of Texas at Dallas (UTD), and 48 stations from the Defense Mapping Agency (DMA). This investigation is an effort to study several areas for potential storage of high-level radioactive waste. Gravity stations established under YMP are shown. The objective of this gravity survey was to explore for the presence of plutons. This volume contains only compiled data

Principal facts for about 16,000 gravity stations in the Nevada Test Site and vicinity

International Nuclear Information System (INIS)

Harris, R.N.; Ponce, D.A.; Oliver, H.W.; Healey, D.L.

1989-01-01

The Nevada Test Site (NTS) and vicinity includes portions of the Goldfield, Caliente, Death Valley, and Las Vegas. This report documents and consolidates previously published and recently compiled gravity data to establish a gravity data base of about 16,000 stations for the NTS and vicinity. While compiling data sets, redundant stations and stations having doubtful locations or gravity values were excluded. Details of compiling the gravity data sets are discussed in later sections. Where feasible, an accuracy code has been assigned to each station so that the accuracy or reliability of each station can be evaluated. This data base was used in preparing complete Bouguer and isostatic gravity maps of the NTS and vicinity. Since publication of the complete Bouguer gravity map, additional data were incorporated into the isostatic gravity map. Gravity data were compiled from five sources: 14,183 stations from the US Geological Survey (USGS), 326 stations from Exploration Data Consultants (EDCON) of Denver, Colorado, 906 stations from the Los Alamos National Laboratory (LANL), 212 stations from the University of Texas at Dallas (UTD), and 48 stations from the Defense Mapping Agency (DMA). This investigation is an effort to study several areas for potential storage of high-level radioactive waste. Gravity stations established under YMP are shown. The objective of this gravity survey was to explore for the presence of plutons. 33 refs., 24 figs., 9 tabs

Non-Coop Station History

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Station history documentation for stations outside the US Cooperative Observer network. Primarily National Weather Service stations assigned WBAN station IDs. Other...

Safety and exportation of nuclear power stations

International Nuclear Information System (INIS)

Coudray, M.; Perrais, J.P.

1976-01-01

Safety problems arising from exportation are especially handled through the French exportation of PWR stations. Regulations differ widely from one country to another. However, very large use of American regulations is made and frequently there is a tendency to harden such or such clause in the quotation. Industry must be ready to give satisfaction to such demands of customers. Sometimes also, it is a mere duplication of French stations which is above all looked for. In that case, it is the problem of using French regulations abroad which arises. Desirable changes in examination proceedings are analyzed together with a French regulation effort aiming to make easier the promotion of their use abroad. Finally, safety may be a factor of success for exportation attempts. It is shown how useless some outbiddings may be, but also how, on the contrary, speeding up of research and development effort towards specific safety problems in case of exportation, is to be promoted [fr

Radiation protection considerations in space station missions

International Nuclear Information System (INIS)

Peddicord, K.L.; Bolch, W.E.

1991-01-01

The National Aeronautics and Space Administration (NASA) is currently studying the degree to which the baseline design of space station Freedom (SSF) would permit its evolution to a transportation node for lunar or Mars expeditions. To accomplish NASA's more ambitious exploration goals, nuclear-powered vehicles could be used in SSF's vicinity. This enhanced radiation environment around SSF could necessitate additional crew shielding to maintain cumulative doses below recommended limits. This paper presents analysis of radiation doses received upon the return and subsequent unloading of Mars vehicles utilizing either nuclear electric propulsion (NEP) or nuclear thermal rocket (NTR) propulsion systems. No inherent shielding by the vehicle structure or space station is assumed; consequently, the only operational parameters available to control radiation doses are the source-to-target distance and the reactor shutdown time prior to the exposure period. For the operations planning, estimated doses are shown with respect to recommended dose limits and doses due solely to the natural space environment in low Earth orbit

47 CFR 80.107 - Service of private coast stations and marine-utility stations.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 5 2010-10-01 2010-10-01 false Service of private coast stations and marine...) SAFETY AND SPECIAL RADIO SERVICES STATIONS IN THE MARITIME SERVICES Operating Requirements and Procedures Operating Procedures-Land Stations § 80.107 Service of private coast stations and marine-utility stations. A...

Transverse Characteristics of Hadron Production in Elementary and Nuclear Collisions at the CERN SPS Energies

CERN Document Server

AUTHOR|(CDS)2076476; Bialkowska, H

2004-01-01

A comprehensive study of transverse phenomena at CERN-SPS energies has been performed using data collected by the NA49 experiment. Results on p, p, pi+ and pi- production in elementary hadronic interactions (p + p, pi+ +p and pi- + p) as well as in nuclear collisions (centrality-defined p + Pb, C + C, Si + Si And Pb + Pb) are presented. The dependence of transverse momentum spectra, and in particular the - xF correlations, on particle species, collision energy, size and structure of the colliding objects has been investigated. Particle composition, in terms of the nuclear modification factors RpA (pT) for different xF regions – and particle ratios, has been also studied. The whole set of experimental data puts strong constraints on theoretical models aiming at the description of hadron production in the studied reactions.

A new spark detection system for the electrostatic septa of the SPS North (experimental) Area

CERN Multimedia

Barlow, R A; Borburgh, J; Carlier, E; Chanavat, C; Pinget, B

2013-01-01

Electrostatic septa (ZS) are used in the extraction of the particle beams from the CERN SPS to the North Area experimental zone. These septa employ high electric fields, generated from a 300 kV power supply, and are particularly prone to internal sparking around the cathode structure. This sparking degrades the electric field quality, consequently affecting the extracted beam, vacuum and equipment performance. To mitigate these effects, a Spark Detection System (SDS) has been realised, which is based on an industrial SIEMENS S7-400 programmable logic controller and deported Boolean processors modules interfaced through a PROFINET fieldbus. The SDS interlock logic uses a moving average spark rate count to determine if the ZS performance is acceptable. Below a certain spark rate it is probable that the ZS septa tank vacuum can recover, thus avoiding transition into a\

Event-by-event fluctuations of the mean transverse momentum $M_{p_{T}}$ at SPS energies

CERN Document Server

Appelshäuser, Harald

2004-01-01

The study of event-by-event fluctuations has been proposed as a tool to investigate the properties of hot and dense nuclear matter created in nuclear collisions. Significant fluctuations of the mean transverse momentum beyond purely statistical ones may signal the passage of the system through the QCD phase boundary or close to the critical point. Fluctuations of M/sub PT/ provide valuable information about the dynamical evolution of A A collisions. In this contribution, recent measurements by the CERES experiment at the CERN-SPS are discussed. The analysis comprises a centrality dependent study of M/sub PT/ fluctuations near mid-rapidity in Pb-Au collisions at 40, 80, and 158 A GeV/c. The non-statistical (dynamical) contribution to M/sub PT/ fluctuations has been evaluated in terms of the fluctuation measure Sigma /sub PT/.

47 CFR 73.6016 - Digital Class A TV station protection of TV broadcast stations.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Digital Class A TV station protection of TV... Class A TV station protection of TV broadcast stations. Digital Class A TV stations must protect authorized TV broadcast stations, applications for minor changes in authorized TV broadcast stations filed on...

Fire Stations

Data.gov (United States)

Department of Homeland Security — Fire Stations in the United States Any location where fire fighters are stationed or based out of, or where equipment that such personnel use in carrying out their...

Do cities deserve more railway stations? The choice of a departure railway station in a multiple-station region

NARCIS (Netherlands)

Givoni, M.; Rietveld, P.

2014-01-01

Promoting the use of rail is an important element in sustainable transport policy. One of the most important decisions to make in planning the railway network is on the number of stations to provide. Stations are the access points to rail services and while each additional station increases rail's

47 CFR 73.6018 - Digital Class A TV station protection of DTV stations.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Digital Class A TV station protection of DTV... TV station protection of DTV stations. Digital Class A TV stations must protect the DTV service that... application for digital operation of an existing Class A TV station or to change the facilities of a digital...

Novel Base Station MIMO Antennas with Enhanced Spectral Efficiencies Using Angular Reuse

Directory of Open Access Journals (Sweden)

Miguel Mora-Andreu

2015-01-01

Full Text Available The true polarization diversity (TPD technique is combined with the spatial diversity technique in novel MIMO antenna array geometries with a large number of elements. The use of a large number of elements requires some angular reuse within the array for polarization diversity. With designs compatible with existing base station antenna array configurations, the novel geometries with combining diversity schemes are shown to be able to achieve near the maximum spectral efficiencies. True polarization diversity (TPD schemes are found to be an excellent complement to more conventional spatial diversity schemes for obtaining optimum MIMO array performance in base station antennas.

SPS Fabrication of Tungsten-Rhenium Alloys in Support of NTR Fuels Development

International Nuclear Information System (INIS)

Webb, Jonathan A.; Charit, Indrajit; Sparks, Cory; Butt, Darryl P.; Frary, Megan; Carroll, Mark

2011-01-01

Tungsten metal slugs were fabricated via Spark Plasma Sintering (SPS) of powdered metals at temperatures ranging from 1575 K to 1975 K and hold times of 5 minutes to 30 minutes, using powders with an average diameter of 7.8 ?m. Sintered tungsten specimens were found to have relative densities ranging from 83 % to 94 % of the theoretical density for tungsten. Consolidated specimens were also tested for their Vickers Hardness Number (VHN), which was fitted as a function of relative density; the fully consolidated VHN was extrapolated to be 381.45 kg/mm2. Concurrently, tungsten and rhenium powders with average respective diameters of 0.5 ?m and 13.3 ?m were pre-processed either by High-Energy-Ball-Milling (HEBM) or by homogeneous mixing to yield W-25at.%Re mixtures. The powder batches were sintered at temperatures of 1975 K and 2175 K for hold times ranging from 0 minutes to 60 minutes yielding relative densities ranging from 94% to 97%. The combination of HEBM and sintering showed a significant decrease in the inter-metallic phases compared to that of the homogenous mixing and sintering.

High power semiconductor switches in the 12 kV, 50 kA pulse generator of the SPS beam dump kicker system

CERN Document Server

Bonthond, J; Faure, P; Vossenberg, Eugène B

2001-01-01

Horizontal deflection of the beam in the dump kicker system of the CERN SPS accelerator is obtained with a series of fast pulsed magnets. The high current pulses of 50 kA per magnet are generated with capacitor discharge type generators which, combined with a resistive free-wheel diode circuit, deliver a critically damped half-sine current with a rise-time of 25 ms. Each generator consists of two 25 kA units, connected in parallel to a magnet via a low inductance transmission line.

From city’s station to station city. An integrative spatial approach to the (redevelopment of station areas

Directory of Open Access Journals (Sweden)

Ana Luísa Martins da Conceição

2014-12-01

Full Text Available Since its origin, the railway station has had a complicated relationship with the city, demanding periodical updates, particularly regarding spatial issues. With the aim of improving the liveability of station areas, current redevelopment projects are reconceptualising them as balanced transport ‘nodes’ and ‘places’ in the city. However, the proposed spatial solutions do not fully support the sought after economic, social and environmental performances. These intentions continue to be predominantly bounded with the (abstract planological level, not finding appropriate translation at the (concrete spatial design level. Further, the interdisciplinary nature of the highly complex planning and design processes of station areas, which should contribute to enhance the performance of their spaces, reinforces constraints and relegates architecture to a marginal role in this quest. It is thus necessary to understand how architecture can contribute to the improvement of the spatial performance of contemporary stations areas, supporting their current reconceptualization. To gain this understanding, the research explored the factors which influence the spatial definition and performance of European High Speed Train station areas, using “design research” and “research by design”. Via a theoretical integrative framework, synthesized from knowledge developed by architecture and other sciences, case studies of ‘through’ stations were analysed and compared. Six cases, encapsulating the most recurrent relative positions of the railway (infrastructure and the station building towards the(ir direct built environment, were chosen out of a large sample. For each category (cases with railway tracks at (a ground level, (b elevated level and (c underground level, two cases, featuring an adapted station building and a newly built one, were studied. Their physical and functional characteristics were mapped at several scales and moments (in history, as

Geodesy and metrology at CERN a source of economy for the SPS programme

International Nuclear Information System (INIS)

Gervaise, J.

1976-01-01

This report gives a broad description of the major options adopted at the start of the project in order to meet the three challenges imposed on the geodesists engaged in survey work for the CERN 400 GeV proton synchrotron (SPS). The methods and means used are dealt with in a general manner. In the conclusion a critical study is made of the results obtained. From a different aspect, a description of the Survey Group's responsibilities highlights the extent of the savings that can be made by a well-trained group carrying out high-precision measurements. The physical dimensions of the project and the complexity of the work involved in building a second-generation accelerator demand high standards of precision since these condition the proper operation of the machine. Only by making extensive preliminary studies and precise survey work above and below ground-level over a number of years, was it possible to ensure that the final geodetic and metrological measurements would be completed at high speed and low cost. (Auth.)

Two-particle correlations in p+p and Pb+Pb collisions at SPS energies

CERN Document Server

AUTHOR|(CDS)2081214

In this thesis two-particle correlations in pseudorapidity and azimuthal angle in p+p collisions at beam momenta: 20, 31, 40, 80, and 158 GeV/c are presented. Data were recorded in the NA61/SHINE experiment at the CERN Super Proton Synchrotron (SPS). The results are compared to the EPOS and the UrQMD models as well as to the results from various experiments at the Relativistic Heavy-Ion Collider (RHIC) and the Large Hadron Collider (LHC). Dedicated comparison analysis was done also on NA49 data of Pb+Pb collisions. The inclusive results in p+p show correlation structures connected with resonance decays, Bose-Einstein statistics, momentum conservation, and strings fragmentation. No structures connected with hard processes were observed even at 158 GeV/c beam momentum. The EPOS model reproduces data fine except of Bose-Einstein enhancement; the UrQMD model shows many disagreements with data. The results provide an insight into forgotten realm of soft physics where jet peaks do not cast shadows onto two-particle...

Tests of Bubble Damage Detectors in a Heavy Ion Beam from the SPS

CERN Multimedia

2002-01-01

This experiment is designed to investigate the properties of a bubble damage polymer (BDP) using ion beams from the SPS. These polymers are already used commercially for making neutron and gamma-ray dosimeters. \\\\ \\\\ An attractive feature of BDP detectors is the ability to ``design'' a material to have a particular dE/dx threshold which can be used to detect such objects as monopoles and heavy ions as well as relativistic, singly charged tracks originating f particle interactions. \\\\ \\\\ The BDP detector is a polymer which holds droplets of super-heated liquid in suspension. The droplet size is typically a few microns and the droplet density is normally between 10|5 and 10|7 droplets/cm|3. The passage of a particle with a dE/dx exceeding the threshold of the material will cause the droplets with a sufficiently s parameter to change state, giving rise to bubbles. The dE/dx threshold of the BDP varies with pressure and temperature. The growth of bubbles in the bubble trail is limited by the polymer matrix and th...

Hygienic situation in the site of nuclear power stations in Fukushima Prefecture

International Nuclear Information System (INIS)

Sakka, Masatoshi

1984-01-01

In the Fukushima No. 1 Nuclear Power Station in Fukushima Prefecture, the hygienic statistics for ten years each before and after the start of the power station were compared between the surrounding radiation monitoring area and the reference area without such monitoring, both areas containing populations. There was no difference at all between the two areas. It was thus shown that the nuclear power generation had no adverse effect on the health of the people. The following statistics in both areas concerning the health of the populations are described: external exposure dose, internal exposure sources, whole-body exposure dose, the change of the hygienic state around the power station, the number of deaths and mortality in the areas, the deaths from cancer in the areas, the health of children, the causes of deaths in Fukushima Prefecture. (Mori, K.)

Faisceau d'essai de la NASA au CERN

CERN Multimedia

1999-01-01

An international team coordinated by the Goddard Space Centre, has just finished a series of test beams at SPS, CERN. The experiments were part of the ACCESS experiment, which will eventually monitor cosmic rays from the international space station (1 paragraph).

Solar-assisted MED treatment of Eskom power station waste water

Science.gov (United States)

Roos, Thomas H.; Rogers, David E. C.; Gericke, Gerhard

2017-06-01

The comparative benefits of multi-effect distillation (MED) used in conjunction with Nano Filtration (NF), Reverse Osmosis (RO) and Eutectic Freeze Crystallization (EFC) are determined for waste water minimization for inland coal fired power stations for Zero Liquid Effluent Discharge (ZLED). A sequence of technologies is proposed to achieve maximal water recovery and brine concentration: NF - physico-chemical treatment - MED - EFC. The possibility of extending the concentration of RO reject arising from minewater treatment at the Lethabo power station with MED alone is evaluated with mineral formation modelling using the thermochemical modelling software Phreeq-C. It is shown that pretreatment is essential to extend the amount of water that can be recovered, and this can be beneficially supported by NF.

Preliminary safety evaluation for the plutonium stabilization and packaging system

International Nuclear Information System (INIS)

Shapley, J.E.

1997-01-01

This Preliminary Safety Evaluation (PSE) describes and analyzes the installation and operation of the Plutonium Stabilization and Packaging System (SPS) at the Plutonium Finishing Plant (PFP). The SPS is a combination of components required to expedite the safe and timely storage of Plutonium (Pu) oxide. The SPS program will receive site Pu packages, process the Pu for storage, package the Pu into metallic containers, and safely store the containers in a specially modified storage vault. The location of the SPS will be in the 2736- ZB building and the storage vaults will be in the 2736-Z building of the PFP, as shown in Figure 1-1. The SPS will produce storage canisters that are larger than those currently used for Pu storage at the PFP. Therefore, the existing storage areas within the PFP secure vaults will require modification. Other modifications will be performed on the 2736-ZB building complex to facilitate the installation and operation of the SPS

Estimating Pedestrian flows at train stations using the Station Transfer Model

NARCIS (Netherlands)

Van den Heuvel, J.P.A.; Dekkers, K.; De Vos, S.

2012-01-01

Train stations play a vital role in the door to door travel experience of train passengers. From the passengers’ value of time perspective, the station is the weakest link in total time value of the journey. Within the station the transfer function – moving between the various transport modes and

Broadcasting Stations of the World; Part III. Frequency Modulation Broadcasting Stations.

Science.gov (United States)

Foreign Broadcast Information Service, Washington, DC.

This third part of "Broadcasting Stations of the World", which lists all reported radio broadcasting and television stations, with the exception of those in the United States which broadcast on domestic channels, covers frequency modulation broadcasting stations. It contains two sections: one indexed alphabetically by country and city, and the…

Throughput of Cellular Systems with Conferencing Mobiles and Cooperative Base Stations

Directory of Open Access Journals (Sweden)

Somekh O

2008-01-01

Full Text Available This paper considers an enhancement to multicell processing for the uplink of a cellular system, whereby the mobile stations are allowed to exchange messages on orthogonal channels of fixed capacity (conferencing. Both conferencing among mobile stations in different cells and in the same cell (inter- and intracell conferencing, resp. are studied. For both cases, it is shown that a rate-splitting transmission strategy, where part of the message is exchanged on the conferencing channels and then transmitted cooperatively to the base stations, is capacity achieving for sufficiently large conferencing capacity. In case of intercell conferencing, this strategy performs convolutional pre-equalization of the signal encoding the common messages in the spatial domain, where the number of taps of the finite-impulse response equalizer depends on the number of conferencing rounds. Analysis in the low signal-to-noise ratio regime and numerical results validate the advantages of conferencing as a complementary technology to multicell processing.

Development and Optimisation of the SPS and LHC beam diagnostics based on Synchrotron Radiation monitors

CERN Document Server

AUTHOR|(CDS)2081364; Roncarolo, Federico

Measuring the beam transverse emittance is fundamental in every accelerator, in particular for colliders, where its precise determination is essential to maximize the luminosity and thus the performance of the colliding beams.
 Synchrotron Radiation (SR) is a versatile tool for non-destructive beam diagnostics, since its characteristics are closely related to those of the source beam. At CERN, being the only available diagnostics at high beam intensity and energy, SR monitors are exploited as the proton beam size monitor of the two higher energy machines, the Super Proton Synchrotron (SPS) and the Large Hadron Collider (LHC). The thesis work documented in this report focused on the design, development, characterization and optimization of these beam size monitors. Such studies were based on a comprehensive set of theoretical calculations, numerical simulations and experiments. A powerful simulation tool has been developed combining conventional softwares for SR simulation and optics design, thus allowing t...

Search for Invisible Decays of Sub-GeV Dark Photons in Missing-Energy Events at the CERN SPS.

Science.gov (United States)

Banerjee, D; Burtsev, V; Cooke, D; Crivelli, P; Depero, E; Dermenev, A V; Donskov, S V; Dubinin, F; Dusaev, R R; Emmenegger, S; Fabich, A; Frolov, V N; Gardikiotis, A; Gninenko, S N; Hösgen, M; Kachanov, V A; Karneyeu, A E; Ketzer, B; Kirpichnikov, D V; Kirsanov, M M; Kovalenko, S G; Kramarenko, V A; Kravchuk, L V; Krasnikov, N V; Kuleshov, S V; Lyubovitskij, V E; Lysan, V; Matveev, V A; Mikhailov, Yu V; Myalkovskiy, V V; Peshekhonov, V D; Peshekhonov, D V; Petuhov, O; Polyakov, V A; Radics, B; Rubbia, A; Samoylenko, V D; Tikhomirov, V O; Tlisov, D A; Toropin, A N; Trifonov, A Yu; Vasilishin, B; Vasquez Arenas, G; Ulloa, P; Zhukov, K; Zioutas, K

2017-01-06

We report on a direct search for sub-GeV dark photons (A^{'}), which might be produced in the reaction e^{-}Z→e^{-}ZA^{'} via kinetic mixing with photons by 100 GeV electrons incident on an active target in the NA64 experiment at the CERN SPS. The dark photons would decay invisibly into dark matter particles resulting in events with large missing energy. No evidence for such decays was found with 2.75×10^{9} electrons on target. We set new limits on the γ-A^{'} mixing strength and exclude the invisible A^{'} with a mass ≲100  MeV as an explanation of the muon g_{μ}-2 anomaly.

Search for invisible decays of sub-GeV dark photons in missing-energy events at the CERN SPS

CERN Document Server

Banerjee, D.

2017-01-05

We report on a direct search for sub-GeV dark photons (A') which might be produced in the reaction e^- Z \\to e^- Z A' via kinetic mixing with photons by 100 GeV electrons incident on an active target in the NA64 experiment at the CERN SPS. The A's would decay invisibly into dark matter particles resulting in events with large missing energy. No evidence for such decays was found with 2.75\\cdot 10^{9} electrons on target. We set new limits on the \\gamma-A' mixing strength and exclude the invisible A' with a mass < 100 MeV as an explanation of the muon g_\\mu-2 anomaly.

Electronic viewbox: An integrated image diagnostic working station

International Nuclear Information System (INIS)

Minato, K.; Komori, M.; Hirakawa, A.; Kuwahara, M.; Yonekura, Y.; Torizuka, K.; Brill, A.B.

1985-01-01

Recent development in medical imaging technology have been introducing variety of digital images in clinical medicine, and handling these multi-modality digital images in one place is needed for efficient clinical diagnosis. The authors proposed a concept of an integrated image diagnostic working station, in which a physician can look into all clinical images, can select any key image for diagnosis and can read it in detail. A prototype working station named ''Electronic Viewbox'' has been developed for this purpose. It has three distinctive features. 1. The stored images of a patient are shown at a glance. In order to achieve this function, each original image is attached to a small image, where the data are compressed to reserve the essence of the image, and many of these small images are displayed on a CRT screen. This small image is used as an index for picking up a key image in the archived clinical images. 2. The working station is compact enough to be set on a desk. Only two CRTs and a pointing device are assembled. These two CRT screens are used mutually for retrieving key images and for displaying the original images. 3. All operations can be done interactively using cursor and icons

Bonding of TRIP-Steel/Al2O3-(3Y-TZP Composites and (3Y-TZP Ceramic by a Spark Plasma Sintering (SPS Apparatus

Directory of Open Access Journals (Sweden)

Aslan Miriyev

2016-07-01

Full Text Available A combination of the high damage tolerance of TRIP-steel and the extremely low thermal conductivity of partially stabilized zirconia (PSZ can provide controlled thermal-mechanical properties to sandwich-shaped composite specimens comprising these materials. Sintering the (TRIP-steel-PSZ/PSZ sandwich in a single step is very difficult due to differences in the sintering temperature and densification kinetics of the composite and the ceramic powders. In the present study, we successfully applied a two-step approach involving separate SPS consolidation of pure (3Y-TZP and composites containing 20 vol % TRIP-steel, 40 vol % Al2O3 and 40 vol % (3Y-TZP ceramic phase, and subsequent diffusion joining of both sintered components in an SPS apparatus. The microstructure and properties of the sintered and bonded specimens were characterized. No defects at the interface between the TZP and the composite after joining in the 1050–1150 °C temperature range were observed. Only limited grain growth occurred during joining, while crystallite size, hardness, shear strength and the fraction of the monoclinic phase in the TZP ceramic virtually did not change. The slight increase of the TZP layer’s fracture toughness with the joining temperature was attributed to the effect of grain size on transformation toughening.

Guidelines for Learning Stations.

Science.gov (United States)

Fehrle, Carl C.; Schulz, Jolene

Guidelines for designing and planning learning stations for pupils at the elementary grade level include suggestions on how to develop a station that will be successful in meeting the learners' needs. Instructions for the use of tapes at a station and matching pupils with stations are given, as are guidelines on classroom arrangement and record…

Developmental state and perspectives of USSR power stations, espec. nuclear power stations

International Nuclear Information System (INIS)

1983-01-01

According to the resolutions of the 25th and 26th party congresses of the CPSU, the Soviet electric and thermal energy economy envisages as the mainstreams in development: Energy projects based on nuclear fuel, i.e. nuclear power stations (NPS), nuclear heat- and -power stations (NHPS) and nuclear heat stations (NHS); fuel-energy complexes: Ekibastuz, Kansk-Achinsk, West-Siberian complex (Tyumen); power stations utilizing non-conventional regenerative energy sources, i.e. solar, geothermal, MHD power stations. Further down, an overview is given on the developmental perspectives of nuclear-heat and nuclear-power economy and on the development of energy management based on fossil fuels. (orig./UA) [de

47 CFR 95.139 - Adding a small base station or a small control station.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 5 2010-10-01 2010-10-01 false Adding a small base station or a small control... base station or a small control station. (a) Except for a GMRS system licensed to a non-individual, one or more small base stations or a small control station may be added to a GMRS system at any point...

Single spectrometer station for neutrino-tagging

International Nuclear Information System (INIS)

Nedyalkov, I.P.

1984-01-01

A neutrino tagging station built with respect to the following scheme is proposed. A beam of muons and kaons passes through a magnetic spectrometer, where the energy of each particle is measured. There are coordinate detectors behind the spectrometer in several planes, where the direction of the trajectory of a given particle is determined. Thus, mesons enter the decay point wth the known 4-momentum. Behind the decay point the direction of μ-meson generated by the decay of parent mesons is measured. It is shown that information is sufficient for determining the kind of parent particle (pion or kaon), the energy and the direction of trajectory of the neutrino

Care management at Ikata Power Station

International Nuclear Information System (INIS)

Sakai, Koji

1982-01-01

For operating nuclear power stations safely and economically, it is necessary to control nuclear fuel itself and reactor cores. Nuclear fuel must be controlled consistently in view of quantitative balance and operational method over the whole nuclear fuel cycle of uranium ore, fabrication, burning in reactors and reprocessing, based on the plan of using fuel in electric power companies. The control of the burning in reactors is called core management, and it is important because the users of fuel execute it. For dealing with such core management works, Shikoku Electric Power Co., Inc., has developed the computer code system for grasping the state of fuel exchange and the burning condition in reactors and used it since 1972. The outline of the core management in Ikata Power Station is reported in this paper centering around computing works. The core management works are divided into those at the time of regular inspection and those in operation. In the regular inspection, fuel inspection, fuel exchange and reactor physics test are performed. In operation, the burning condition of fuel is grasped. The technical computations corresponding to these works are explained, and the examples of computations are shown. (Kako, I.)

Seismic risk control of nuclear power plants using seismic protection systems in stable continental regions: The UK case

Energy Technology Data Exchange (ETDEWEB)

Medel-Vera, Carlos, E-mail: cbmedel@uc.cl; Ji, Tianjian, E-mail: tianjian.ji@manchester.ac.uk

2016-10-15

Highlights: • Strategies to reduce seismic risk for nuclear power stations in the UK are analysed. • Efficiency of devices to reduce risk: viscous-based higher than hysteretic-based. • Scenario-based incremental dynamic analysis is introduced for use in nuclear stations. • Surfaces of seismic unacceptable performance for nuclear stations are proposed. - Abstract: This article analyses three different strategies on the use of seismic protection systems (SPS) for nuclear power plants (NPPs) in the UK. Such strategies are based on the experience reported elsewhere of seismically protected nuclear reactor buildings in other stable continental regions. Analyses are conducted using an example of application based on a 1000 MW Pressurised Water Reactor building located in a representative UK nuclear site. The efficiency of the SPS is probabilistically assessed to achieve possible risk reduction for both rock and soil sites in comparison with conventionally constructed NPPs. Further analyses are conducted to study how the reduction of risk changes when all controlling scenarios of the site are included. This is done by introducing a scenario-based incremental dynamic analysis aimed at the generation of surfaces for unacceptable performance of NPPs as a function of earthquake magnitude (M{sub w}) and distance-to-site (R{sub epi}). General guidelines are proposed to potentially use SPS in future NPPs in the UK. Such recommendations can be used by the British nuclear industry in the future development of 12 new reactors to be built in the next two decades to generate 16 GWe of new nuclear capacity.

Developments of space station; Uchu station no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Hashimoto, H. [National Space Development Agency of Japan, Tokyo (Japan)

1996-03-05

This paper introduces the Japanese experiment module (JEM) in developing a space station. The JEM consists of systems of a pressurizing section, an exposure section, a pressurizing portion of a supply section, a manipulator and an exposure portion of the supply section. The pressurizing section circulates and controls air so that crews can perform experiments under pressurized environment. The exposure section is a part in which experiments are carried out under exposure environment. The supply section runs between a station and the ground, with required devices loaded on it. The manipulator performs attaching a payload for the exposure section and replaces experimental samples. The JEM undergoes a schedule of fabricating an engineering model, testing for a certification a prototype flight model, and putting the model on a flight. The pressurizing section, exposure section and manipulator are at the stage of system tests. Surveillance of the JEM and control of the experiments are carried out at the Tsukuba Space Center. The Center is composed of a space experiment building, a zero-gravity environment testing building, an astronaut training building, a space station operating building, and a space station testing building. 7 figs., 2 tabs.

The influence of sintering temperature on microstructure and mechanical properties of Ni-Al intermetallics fabricated by SPS

Energy Technology Data Exchange (ETDEWEB)

Thömmes, A., E-mail: thoemmes.alexander@gmail.com; Shevtsova, L. I., E-mail: edeliya2010@mail.ru; Laptev, I. S., E-mail: ilya-laptev-nstu@mail.ru; Mul, D. O., E-mail: ddariol@yandex.ru [Novosibirsk State Technical University, Novosibirsk, 630073 (Russian Federation); Mali, V. I., E-mail: vmali@mail.ru; Anisimov, A. G., E-mail: anis@hydro.nsc.ru [Lavrentyev Institute of Hydrodynamics SB RAS, Novosibirsk, 630090 (Russian Federation)

2015-10-27

In the present study PN85Yu15 was used as elemental powder to produce a sintered compound with Ni3Al as main phase. The Spark Plasma Sintering (SPS) technique is used to compact the powders. The powder was sintered in a temperature range between 1000°C and 1150°C to observe the influence of the sintering temperature on the microstructure and the mechanical properties. The microstructure was observed with optical microscope (OM), the phase composition was characterized by X-ray diffraction (XRD) technique. Density and microhardness were observed and compared the values with the results of other researchers. The compressive-, density- and microhardness tests show as clear result that with increasing the sintering temperature nearly all properties become better and also the microstructure studies show that porous places become less.

A new spark detection system for the electrostatic septa of the SPS North (experimental) Area

CERN Document Server

Barlow, R A; Borburgh, J; Carlier, E; Chanavat, C; Fowler, T; Pinget, B

2014-01-01

Electrostatic septa (ZS) are used in the extraction of the particle beams from the CERN SPS to the North Area experimental zone. These septa employ high electric fields, generated from a 300 kV power supply, and are particularly prone to internal sparking around the cathode structure. This sparking degrades the electric field quality, consequently affecting the extracted beam, vacuum and equipment performance. To mitigate these effects, a Spark Detection System (SDS) has been realised, which is based on an industrial SIEMENS S7-400 programmable logic controller and deported Boolean processor modules interfaced through a PROFINET fieldbus. The SDS interlock logic uses a moving average spark rate count to determine if the ZS performance is acceptable. Below a certain spark rate it is probable that the ZS septa tank vacuum can recover, thus avoiding transition into a state where rapid degradation would occur. Above this level an interlock is raised and the high voltage is switched off. Additionally, all spark si...

Effects of helium and deuterium irradiation on SPS sintered W–Ta composites at different temperatures

Energy Technology Data Exchange (ETDEWEB)

Mateus, R., E-mail: rmateus@ipfn.ist.utl.pt [Associação Euratom/IST, Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade Técnica de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Dias, M. [ITN, Instituto Tecnológico e Nuclear, Estrada Nacional 10, 2686-953 Sacavém (Portugal); Lopes, J. [ITN, Instituto Tecnológico e Nuclear, Estrada Nacional 10, 2686-953 Sacavém (Portugal); ISEL, Instituto Superior de Engenharia de Lisboa, Rua Conselheiro Emídio Navarro, 1, 1959-007 Lisboa (Portugal); Rocha, J.; Catarino, N.; Franco, N. [ITN, Instituto Tecnológico e Nuclear, Estrada Nacional 10, 2686-953 Sacavém (Portugal); Livramento, V. [Associação Euratom/IST, Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade Técnica de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); LNEG, Laboratório Nacional de Energia e Geologia, Estrada do Paço do Lumiar, 1649-038 Lisboa (Portugal); and others

2013-11-15

Energetic He{sup +} and D{sup +} ions were implanted into different W–Ta composites in order to investigate their stability under helium and deuterium irradiation. The results were compared with morphological and chemical modifications arising from exposure of pure W and Ta. Special attention was given to tantalum hydride (Ta{sub 2}H) formation due to its implications for tritium inventory. Three W–Ta composites with 10 and 20 at.% Ta were prepared from elemental W powder and Ta fibre or powder through low-energy ball milling in argon atmosphere. Spark plasma sintering (SPS) was used as the consolidation process in the temperature range from 1473 to 1873 K. The results obtained from pure elemental samples and composites are similar. However, Ta{sub 2}H is easily formed in pure Ta by using a pre-implantation stage of He{sup +}, whereas in W–Ta composites the same reaction is clearly reduced, and it can be inhibited by controlling the sintering temperature.

SPS Injection and Beam Quality for LHC Heavy Ions With 150 ns Kicker Rise Time

CERN Document Server

Goddard, Brennan; Ducimetière, Laurent; Kotzian, Gerd; Uythoven, Jan; Velotti, Francesco

2016-01-01

As part of the LHC Injectors Upgrade project for LHC heavy ions, the SPS injection kicker system rise time needs reduction below its present 225 ns. One technically challenging option under consideration is the addition of fast Pulse Forming Lines in parallel to the existing Pulse Forming Networks for the 12 kicker magnets MKP-S, targeting a system field rise time of 100 ns. An alternative option is to optimise the system to approach the existing individual magnet field rise time (2-98%) of 150 ns. This would still significantly increase the number of colliding bunches in LHC while minimising the cost and effort of the system upgrade. The observed characteristics of the present system are described, compared to the expected system rise time, together with results of simulations and measurements with 175 and 150 ns injection batch spacing. The expected beam quality at injection into LHC is quantified, with the emittance growth and simulated tail population taking into account expected jitter and synchronisatio...

Community reaction to noise from power stations

International Nuclear Information System (INIS)

Job, R.F.S.; Hede, A.J.

1989-01-01

Community reaction is a major consideration in noise control. The relationship between noise exposure and community reaction has received considerable attention in relation to railway, traffic, aircraft and impulsive noise. The results have shown a number of features in common, including: similarly shaped noise/reaction functions; similar results across different measurement techniques and cultures, noise/reaction correlations based on individual respondent data are low (mean r = 0.42 ± 0.12: Job, 1988), although correlations of .58 and above have been reported correlations based on data grouped by noise exposure are generally high and relatively unaffected by the type of noise studied whereas correlations based on individual data tend to be lower for impulsive noise than for transportation noise attitude to the noise source and sensitivity to noise shows strong correlations with reaction. This paper reports that the present study was undertaken in order toe establish over a wider range of noise exposure whether community reaction to power station noise is similar to reaction to other types of non-impulsive noise. It is possible that reaction is different given important differences in the source of the noise which may affect attitude. Attitudes towards power stations may be more positive than attitudes to aircraft or rail noise for example, because almost all respondents use electricity regularly every day. Further, the power stations in the present study provided employment for the relatively small surrounding communities

Newport Research Station

Data.gov (United States)

Federal Laboratory Consortium — The Newport Research Station is the Center's only ocean-port research facility. This station is located at Oregon State University's Hatfield Marine Science Center,...

Benchmark of the SixTrack-Fluka Active Coupling Against the SPS Scrapers Burst Test

CERN Multimedia

Mereghetti, A; Cerutti, F

2014-01-01

The SPS scrapers are a key ingredient for the clean injection into the LHC: they cut off halo particles quite close to the beam core (e.g.~3.5 sigma) just before extraction, to minimise the risk for quenches. The improved beam parameters as envisaged by the LHC Injectors Upgrade (LIU) Project required a revision of the present system, to assess its suitability and robustness. In particular, a burst (i.e. endurance) test of the scraper blades has been carried out, with the whole bunch train being scraped at the centre (worst working conditions). In order to take into account the effect of betatron and longitudinal beam dynamics on energy deposition patterns, and nuclear and Coulomb scattering in the absorbing medium onto loss patterns, the SixTrack and Fluka codes have been coupled, profiting from the best of the refined physical models they respectively embed. The coupling envisages an active exchange of tracked particles between the two codes at each turn, and an on-line aperture check in SixTrack, in order ...

Exposure of CR39 Stacks to Oxygen and Sulphur Beams at the CERN-SPS

CERN Multimedia

2002-01-01

We plan to expose 8 stacks of CR39 sheets to oxygen and sulphur ions of 60 and 200~GeV at the CERN-SPS.\\\\ \\\\ The main purpose of the exposures is the calibration of the CR39 sheets used for a large area experimental search for magnetic monopoles at the Gran Sasso Laboratory (experiment MACRO). \\\\ \\\\ The stacks have 20~layers of CR39, each layer 13~cm~x~7~cm and 1.4~mm thick. A copper absorber is located after the first 6 layers. \\\\ \\\\ We require exposures of about 2000 tracks per cm$^2$ over the entire area of the stack with a uniform illumination. The standard beam used for the emulsion experiments is normally adequate for this purpose.\\\\ \\\\ We have performed one exposure to sulphur ions. The etched tracks have been measured automatically with the Elbeck image analyser system. We measured the incoming sulphur ions as well as the nuclear fragments produced in the copper absorber. Clean separation among the peaks due to the various fragments is obtained (there is no indication of nuclei with fractional electri...

Station Set Residual: Event Classification Using Historical Distribution of Observing Stations

Science.gov (United States)

Procopio, Mike; Lewis, Jennifer; Young, Chris

2010-05-01

Analysts working at the International Data Centre in support of treaty monitoring through the Comprehensive Nuclear-Test-Ban Treaty Organization spend a significant amount of time reviewing hypothesized seismic events produced by an automatic processing system. When reviewing these events to determine their legitimacy, analysts take a variety of approaches that rely heavily on training and past experience. One method used by analysts to gauge the validity of an event involves examining the set of stations involved in the detection of an event. In particular, leveraging past experience, an analyst can say that an event located in a certain part of the world is expected to be detected by Stations A, B, and C. Implicit in this statement is that such an event would usually not be detected by Stations X, Y, or Z. For some well understood parts of the world, the absence of one or more "expected" stations—or the presence of one or more "unexpected" stations—is correlated with a hypothesized event's legitimacy and to its survival to the event bulletin. The primary objective of this research is to formalize and quantify the difference between the observed set of stations detecting some hypothesized event, versus the expected set of stations historically associated with detecting similar nearby events close in magnitude. This Station Set Residual can be quantified in many ways, some of which are correlated with the analysts' determination of whether or not the event is valid. We propose that this Station Set Residual score can be used to screen out certain classes of "false" events produced by automatic processing with a high degree of confidence, reducing the analyst burden. Moreover, we propose that the visualization of the historically expected distribution of detecting stations can be immediately useful as an analyst aid during their review process.

Strangeness production in heavy ion collisions: What have we learned with the energy increase from SPS to RHIC

International Nuclear Information System (INIS)

Odyniec, Grazyna

2002-01-01

A review of strange particle production in heavy ion collisions at ultrarelativistic energies is presented. The particle yields and ratios from SPS and RHIC are discussed in view of the newest developments in understanding collision dynamics, and in view of their role in the search for a quark gluon plasma. A strangeness enhancement, most notably observed in CERN Pb-beam results, shows a remarkable two fold global enhancement with a much larger effect seen in the case of multistrange baryons. Hadronic models did fail to explain this pattern. At RHIC energy strangeness assumes a different role, since temperatures are higher and the central rapidity region almost baryon-free. An intriguing question: ''Did RHIC change the way we understand strangeness production in heavy ion collisions ?'' is discussed

Weather Radar Stations

Data.gov (United States)

Department of Homeland Security — These data represent Next-Generation Radar (NEXRAD) and Terminal Doppler Weather Radar (TDWR) weather radar stations within the US. The NEXRAD radar stations are...

Comparison of the CATHENA model of Gentilly-2 end shield cooling system predictions to station data

Energy Technology Data Exchange (ETDEWEB)

Zagre, G.; Sabourin, G. [Candu Energy Inc., Montreal, Quebec (Canada); Chapados, S. [Hydro-Quebec, Montreal, Quebec (Canada)

2012-07-01

As part of the Gentilly-2 Refurbishment Project, Hydro-Quebec has elected to perform the End Shield Cooling Safety Analysis. A CATHENA model of Gentilly-2 End Shield Cooling System was developed for this purpose. This model includes new elements compared to other CANDU6 End Shield Cooling models such as a detailed heat exchanger and control logic model. In order to test the model robustness and accuracy, the model predictions were compared with plant measurements.This paper summarizes this comparison between the model predictions and the station measurements. It is shown that the CATHENA model is flexible and accurate enough to predict station measurements for critical parameters, and the detailed heat exchanger model allows reproducing station transients. (author)

Analysis of Synchronization Impairments for Cooperative Base Stations Using OFDM

Directory of Open Access Journals (Sweden)

Konstantinos Manolakis

2015-01-01

Full Text Available Base station cooperation is envisioned as a key technology for future cellular networks, as it has the potential to eliminate intercell interference and to enhance spectral efficiency. To date, there is still lack of understanding of how imperfect carrier and sampling frequency synchronization between transmitters and receivers limit the potential gains and what the actual system requirements are. In this paper, OFDM signal model is established for multiuser multicellular networks, describing the joint effect of multiple carrier and sampling frequency offsets. It is shown that the impact of sampling offsets is much smaller than the impact of carrier frequency offsets. The model is extended to the downlink of base-coordinated networks and closed-form expressions are derived for the mean power of users’ self-signal, interuser, and intercarrier interference, whereas it is shown that interuser interference is the main source of degradation. The SIR is inverse to the base stations’ carrier frequency variance and to the square of time since the last precoder update, whereas it grows with the number of base stations and drops with the number of users. Through user selection, the derived SIR upper bound can be approached. Finally, system design recommendations for meeting synchronization requirements are provided.

UMTS Network Stations

Science.gov (United States)

Hernandez, C.

2010-09-01

The weakness of small island electrical grids implies a handicap for the electrical generation with renewable energy sources. With the intention of maximizing the installation of photovoltaic generators in the Canary Islands, arises the need to develop a solar forecasting system that allows knowing in advance the amount of PV generated electricity that will be going into the grid, from the installed PV power plants installed in the island. The forecasting tools need to get feedback from real weather data in "real time" from remote weather stations. Nevertheless, the transference of this data to the calculation computer servers is very complicated with the old point to point telecommunication systems that, neither allow the transfer of data from several remote weather stations simultaneously nor high frequency of sampling of weather parameters due to slowness of the connection. This one project has developed a telecommunications infrastructure that allows sensorizadas remote stations, to send data of its sensors, once every minute and simultaneously, to the calculation server running the solar forecasting numerical models. For it, the Canary Islands Institute of Technology has added a sophisticated communications network to its 30 weather stations measuring irradiation at strategic sites, areas with high penetration of photovoltaic generation or that have potential to host in the future photovoltaic power plants connected to the grid. In each one of the stations, irradiance and temperature measurement instruments have been installed, over inclined silicon cell, global radiation on horizontal surface and room temperature. Mobile telephone devices have been installed and programmed in each one of the weather stations, which allow the transfer of their data taking advantage of the UMTS service offered by the local telephone operator. Every minute the computer server running the numerical weather forecasting models receives data inputs from 120 instruments distributed

Streamflow Gaging Stations

Data.gov (United States)

Department of Homeland Security — This map layer shows selected streamflow gaging stations of the United States, Puerto Rico, and the U.S. Virgin Islands, in 2013. Gaging stations, or gages, measure...

Ocean Station Vessel

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Ocean Station Vessels (OSV) or Weather Ships captured atmospheric conditions while being stationed continuously in a single location. While While most of the...

Establishing a mobile automatic monitoring station for emergency response

International Nuclear Information System (INIS)

Fang, Hsin-Fa

2008-01-01

Full text: A radiological/nuclear emergency event may cause environmental contamination. The emergency response works always need to plan an environmental survey programme incorporating the assessment results to see what is happening. The places where are assessed to have the highest radioactive contamination/radiation dose will catch more concern and need continuous monitoring. It will cause unnecessary dangers and dose to command that personnel conduct surveying in such places when the radiological/nuclear accident become more severe. A mobile automatic monitoring station has been established for emergency response by INER (Institute of Nuclear Energy Research) to solve the problem practically. The monitoring station involves a HPIC to monitor radiation dose, an anemometer to monitor wind speed and direction, a GPS to get position data, a GPRS/3G communication module to send monitoring and positioning data to the monitoring centre where can show the monitoring result directly on a map shown on the computer. These instruments are integrated in a trailer easy to be towed to the place need to be monitored. The electric power of the station is supplied by s a solar power energy system. It can supply the station working at least 10 days without extra electric power supply designed based on the expected time length of a nuclear power plant event. The HPIC is very sensitive and stable that can discriminate a 10 nSv/hr increasing of dose rate with the monitoring time period every ten seconds. Where the radiological dispersion device events happened is not predictable, it is difficult to get suitable wind monitoring data to assess the result of radiological dispersion device events. The anemometer added on the station can provide the real time wind monitoring data to help assessment works. (author)

Seismic monitoring at Deception Island volcano (Antarctica): the 2010-2011 survey

Science.gov (United States)

Martín, R.; Carmona, E.; Almendros, J.; Serrano, I.; Villaseñor, A.; Galeano, J.

2012-04-01

As an example of the recent advances introduced in seismic monitoring of Deception Island volcano (Antarctica) during recent years, we describe the instrumental network deployed during the 2010-2011 survey by the Instituto Andaluz de Geofísica of University of Granada, Spain (IAG-UGR). The period of operation extended from December 19, 2010 to March 5, 2011. We deployed a wireless seismic network composed by four three-component seismic stations. These stations are based on 24-bit SL04 SARA dataloggers sampling at 100 sps. They use a PC with embedded linux and SEISLOG data acquisition software. We use two types of three-component seismometers: short-period Mark L4C with natural frequency of 1 Hz and medium-period Lennartz3D/5s with natural frequency of 0.2 Hz. The network was designed for an optimum spatial coverage of the northern half of Deception, where a magma chamber has been reported. Station locations include the vicinity of the Spanish base "Gabriel de Castilla" (GdC), Obsidianas Beach, a zone near the craters from the 1970 eruptions, and the Chilean Shelter located south of Pendulum Cove. Continuous data from the local seismic network are received in real-time in the base by wifi transmission. We used Ubiquiti Networks Nanostation2 antennas with 2.4 GHz, dual-polarity, 10 dBi gain, and 54 Mbps transmission rate. They have shown a great robustness and speed for real-time applications. To prioritize data acquisition when the battery level is low, we have designed a circuit that allows independent power management for the seismic station and wireless transmission system. The reception antenna located at GdC is connected to a computer running SEISCOMP. This software supports several transmission protocols and manages the visualization and recording of seismic data, including the generation of summary plots to show the seismic activity. These twelve data channels are stored in miniseed format and displayed in real time, which allows for a rapid evaluation of

Detection rate of serrated polyps and serrated polyposis syndrome in colorectal cancer screening cohorts: a European overview.

Science.gov (United States)

IJspeert, J E G; Bevan, R; Senore, C; Kaminski, M F; Kuipers, E J; Mroz, A; Bessa, X; Cassoni, P; Hassan, C; Repici, A; Balaguer, F; Rees, C J; Dekker, E

2017-07-01

The role of serrated polyps (SPs) as colorectal cancer precursor is increasingly recognised. However, the true prevalence SPs is largely unknown. We aimed to evaluate the detection rate of SPs subtypes as well as serrated polyposis syndrome (SPS) among European screening cohorts. Prospectively collected screening cohorts of ≥1000 individuals were eligible for inclusion. Colonoscopies performed before 2009 and/or in individuals aged below 50 were excluded. Rate of SPs was assessed, categorised for histology, location and size. Age-sex-standardised number needed to screen (NNS) to detect SPs were calculated. Rate of SPS was assessed in cohorts with known colonoscopy follow-up data. Clinically relevant SPs (regarded as a separate entity) were defined as SPs ≥10 mm and/or SPs >5 mm in the proximal colon. Three faecal occult blood test (FOBT) screening cohorts and two primary colonoscopy screening cohorts (range 1.426-205.949 individuals) were included. Rate of SPs ranged between 15.1% and 27.2% (median 19.5%), of sessile serrated polyps between 2.2% and 4.8% (median 3.3%) and of clinically relevant SPs between 2.1% and 7.8% (median 4.6%). Rate of SPs was similar in FOBT-based cohorts as in colonoscopy screening cohorts. No apparent association between the rate of SP and gender or age was shown. Rate of SPS ranged from 0% to 0.5%, which increased to 0.4% to 0.8% after follow-up colonoscopy. The detection rate of SPs is variable among screening cohorts, and standards for reporting, detection and histopathological assessment should be established. The median rate, as found in this study, may contribute to define uniform minimum standards for males and females between 50 and 75 years of age. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Cooperating expert systems for Space Station - Power/thermal subsystem testbeds

Science.gov (United States)

Wong, Carla M.; Weeks, David J.; Sundberg, Gale R.; Healey, Kathleen L.; Dominick, Jeffrey S.

1988-01-01

The Systems Autonomy Demonstration Project (SADP) is a NASA-sponsored series of increasingly complex demonstrations to show the benefits of integrating knowledge-based systems with conventional process control in real-time, real-world problem domains that can facilitate the operations and availability of major Space Station distributed systems. This paper describes the system design, objectives, approaches, and status of each of the testbed knowledge-based systems. Simplified schematics of the systems are shown.

Reference Climatological Stations

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Reference Climatological Stations (RCS) network represents the first effort by NOAA to create and maintain a nationwide network of stations located only in areas...

Locations of Sampling Stations for Water Quality Monitoring in Water Distribution Networks.

Science.gov (United States)

Rathi, Shweta; Gupta, Rajesh

2014-04-01

Water quality is required to be monitored in the water distribution networks (WDNs) at salient locations to assure the safe quality of water supplied to the consumers. Such monitoring stations (MSs) provide warning against any accidental contaminations. Various objectives like demand coverage, time for detection, volume of water contaminated before detection, extent of contamination, expected population affected prior to detection, detection likelihood and others, have been independently or jointly considered in determining optimal number and location of MSs in WDNs. "Demand coverage" defined as the percentage of network demand monitored by a particular monitoring station is a simple measure to locate MSs. Several methods based on formulation of coverage matrix using pre-specified coverage criteria and optimization have been suggested. Coverage criteria is defined as some minimum percentage of total flow received at the monitoring stations that passed through any upstream node included then as covered node of the monitoring station. Number of monitoring stations increases with the increase in the value of coverage criteria. Thus, the design of monitoring station becomes subjective. A simple methodology is proposed herein which priority wise iteratively selects MSs to achieve targeted demand coverage. The proposed methodology provided the same number and location of MSs for illustrative network as an optimization method did. Further, the proposed method is simple and avoids subjectivity that could arise from the consideration of coverage criteria. The application of methodology is also shown on a WDN of Dharampeth zone (Nagpur city WDN in Maharashtra, India) having 285 nodes and 367 pipes.

Fire Stations - 2007

Data.gov (United States)

Kansas Data Access and Support Center — Fire Station Locations in Kansas Any location where fire fighters are stationed at or based out of, or where equipment that such personnel use in carrying out their...

Fire Stations - 2009

Data.gov (United States)

Kansas Data Access and Support Center — Fire Stations in Kansas Any location where fire fighters are stationed or based out of, or where equipment that such personnel use in carrying out their jobs is...

Photoelectrochemical performance of DSSC with monodisperse and polydisperse ZnO SPs

Energy Technology Data Exchange (ETDEWEB)

Wahyuono, Ruri Agung, E-mail: r-agung-w@ep.its.ac.id; Risanti, Doty D., E-mail: r-agung-w@ep.its.ac.id [Department of Engineering Physics, Institut Teknologi Sepuluh Nopember (Indonesia); Shirosaki, Tomohiro; Nagaoka, Shoji [Kumamoto Industrial Research Institute (Japan); Takafuji, Makoto; Ihara, Hirotaka [Department of Applied Chemistry and Biochemistry, Kumamoto University (Japan)

2014-02-24

Zinc oxide, ZnO, is one of oxide semiconductors being used in DSSC. ZnO is promising material for having fairly higher energy band gap and much higher bulk electron mobility than that of anatase TiO{sub 2}, the most widely used semiconductor for DSSC photoelectrode. This study introduces the synthesis of ZnO by precipitation method. The synthesis involves ZnAc dihydrate and diethylene glycol (DEG) for the chemicals. Various size of ZnO spherical particles (SPs) are obtained in polydisperse and monodisperse particles. Monolayer and bilayer DSSCs are fabricated in sandwich structure and sensitized with N719 dye for 3 and 5 hours. Monolayer DSSC using monodisperse particles (422 nm) is able to generate highest conversion efficiency of 0.569% (V{sub oc} = 541.3 mV, J{sub sc} = 1.92 mA/cm{sup 2}, and fill factor of 54.78%). Bilayer DSSC, i.e. combined 422 - 185 nm ZnO layer, can optimize the photocurrent action spectra in UV regime leading to high conversion efficiency of 0.568 (V{sub oc} = 568.2 mV, J{sub sc} = 2.22 mA/cm{sup 2}, and fill factor of 47.25%). The longer sensitizing time does not always produce better conversion efficiency since it can induce the dissolution of Zn atoms and formation of Zn{sup 2+} - dye resisting the electron transport from dye to ZnO photoelectrode.

[STEM on Station Education

Science.gov (United States)

Lundebjerg, Kristen

2016-01-01

The STEM on Station team is part of Education which is part of the External Relations organization (ERO). ERO has traditional goals based around BHAG (Big Hairy Audacious Goal). The BHAG model is simplified to a saying: Everything we do stimulates actions by others to advance human space exploration. The STEM on Station education initiate is a project focused on bringing off the earth research and learning into classrooms. Educational resources such as lesson plans, activities to connect with the space station and STEM related contests are available and hosted by the STEM on Station team along with their partners such as Texas Instruments. These educational activities engage teachers and students in the current happenings aboard the international space station, inspiring the next generation of space explorers.

Space power transmission

Energy Technology Data Exchange (ETDEWEB)

Kuribayashi, Shizuma [Mitsubishi Heavy Industries, Ltd., Tokyo, (Japan)

1989-10-05

There being a conception to utilize solar energy by use of a space power station (SPS), a method to bring that universal grace to mankind is wireless energy transmission. The wireless energy transmission is regarded to be microwave transmission or laser beam transmission. The microwave transmission is to transmit 2.45GHz band microwave from the SPS to a receiving station on the ground to meet power demand on earth. The microwave, as small in attenuation in atmosphere and resistant against rain and cloud, is made candidate and, however, problematic in influence on organism, necessary large area of receiving antenna and many other points to be studied. While the laser transmission, as more convergent of beam than the microwave transmission, is advantageous with enabling the receiving area to be small and, however, disadvantageous with being not resistant against dust, rain and cloud, if used for the energy transmission between the space and earth. 2 refs., 2 figs.

Longitudinal beam parameters and quality checks of the LHC beam in the SPS: further results and comparisons

CERN Document Server

Papotti, G; Linnecar, T; Shaposhnikova, E; Tückmantel, Joachim; CERN. Geneva. AB Department

2008-01-01

Controlled longitudinal emittance blow up is used, along with other measures, to stabilize the nominal LHC beam in the SPS. Two Machine Development studies (MDs) were carried out in 2007 to evaluate the effectiveness of different noise settings for the longitudinal blow up of the beam. The noise settings are affected by both the presence of the 800 MHz RF system and intensity effects which modify the synchrotron frequency distribution inside the bunch. The results for the first MD are reported in Note [1]. This Note reports on the results of the second MD, carried out on 2007-10-17, as well as the comparison between the two in order to analyse the differences between the two occasions. Figures of merit are used that allow rapid evaluation of the quality of the beam as for example stability and bunch length uniformity across batches.

Station History Of The Seismic Station In Ahmadu Bello University ...

African Journals Online (AJOL)

Dominants in the selected events are events from Meditterranian, East Kazakhstan, India/Burma/China, South and Central America and North Ascension island regions. The limited number of events reporting at the station was due to low operational gain at the station which permitted only events whose magnitudes are ...

The Trencin water power station

International Nuclear Information System (INIS)

2005-01-01

This leaflet describes the Trencin water power station. The Trencin water power station was built seven years after the Dubnica nad Vahom water power station started its operation and was the last stage of the first and the oldest derived cascade of water power stations on the Vah River. After completing water power stations at Ladce (1936), Ilava (1946) and Dubnica nad Vahom (1949) and before constructing the Trencin water power station, the whole second derived cascade of water power stations including water power stations at Kostolna, Nove Mesto nad Vahom and Horna Streda was built as soon as possible mainly because the need to get compensation for discontinued electricity supplies as well as energetic coal from the Czech Republic. Hereby, experiences from the construction of previous grades were used, mainly as far as the dimensioning was concerned, as the fi rst installed power stations had, in comparison with the growing requirements on the electricity supplies, very low absorption capacity - only 150 m 3 .s -1 . Thus the Trencin power station (original name was the Skalka power station) was already dimensioned for the same absorption capacity as the cascade located downstream the river, that is 180 m 3 .s -1 . That was related also to growing demands on electricity supplies during the peaks in the daily electric system load diagram, and thus to the transfer from continuous operation of the water power station to semi-peak or even peak performance. According to the standards of power station classification, the Trencin water power station is a medium size, low pressure, channel power station with two units equipped by Kaplan turbines and synchronous hydro-alternators. The water power station installed capacity is 16.1 MW in total and its designed annual production of electrical energy for medium water year is 85,000 MWh, while the average annual production during the last 30 years is 86,252 MWh. Installed unit has a four-blade Kaplan turbine with the diameter

Tether applications for space station

Science.gov (United States)

Nobles, W.

1986-01-01

A wide variety of space station applications for tethers were reviewed. Many will affect the operation of the station itself while others are in the category of research or scientific platforms. One of the most expensive aspects of operating the space station will be the continuing shuttle traffic to transport logistic supplies and payloads to the space station. If a means can be found to use tethers to improve the efficiency of that transportation operation, it will increase the operating efficiency of the system and reduce the overall cost of the space station. The concept studied consists of using a tether to lower the shuttle from the space station. This results in a transfer of angular momentum and energy from the orbiter to the space station. The consequences of this transfer is studied and how beneficial use can be made of it.

Detecting earthquakes over a seismic network using single-station similarity measures

Science.gov (United States)

Bergen, Karianne J.; Beroza, Gregory C.

2018-06-01

New blind waveform-similarity-based detection methods, such as Fingerprint and Similarity Thresholding (FAST), have shown promise for detecting weak signals in long-duration, continuous waveform data. While blind detectors are capable of identifying similar or repeating waveforms without templates, they can also be susceptible to false detections due to local correlated noise. In this work, we present a set of three new methods that allow us to extend single-station similarity-based detection over a seismic network; event-pair extraction, pairwise pseudo-association, and event resolution complete a post-processing pipeline that combines single-station similarity measures (e.g. FAST sparse similarity matrix) from each station in a network into a list of candidate events. The core technique, pairwise pseudo-association, leverages the pairwise structure of event detections in its network detection model, which allows it to identify events observed at multiple stations in the network without modeling the expected moveout. Though our approach is general, we apply it to extend FAST over a sparse seismic network. We demonstrate that our network-based extension of FAST is both sensitive and maintains a low false detection rate. As a test case, we apply our approach to 2 weeks of continuous waveform data from five stations during the foreshock sequence prior to the 2014 Mw 8.2 Iquique earthquake. Our method identifies nearly five times as many events as the local seismicity catalogue (including 95 per cent of the catalogue events), and less than 1 per cent of these candidate events are false detections.

LAYOUT AND DESIGN OF ELECTROMOBILE CHARGING STATIONS AS URBAN ELEMENTS

OpenAIRE

Tomáš Chovan; Martin Straka

2015-01-01

The contribution is dedicated to the processing of the problems of the insufficient charging for the electric vehicles within the concrete urbanistic centre. It brings a different perspective on the mobility, which is shown in the form of electric energy as the alternative for the needs of urbanization of the cities. It analyses electromobility, new technologies in the field of electric vehicles and the charging stations as the elements of the urbanism. In terms of the solution, t...

Mobile environmental radiation monitoring station

International Nuclear Information System (INIS)

Assido, H.; Shemesh, Y.; Mazor, T.; Tal, N.; Barak, D.

1997-01-01

A mobile environmental radiation monitoring station has been developed and established for the Israeli Ministry of Environment. The radiation monitoring station is ready for immediate placing in any required location, or can be operated from a vehicle. The station collects data Tom the detector and transfers it via cellular communication network to a Computerized Control Center for data storage, processing, and display . The mobile station is fully controlled from the. Routinely, the mobile station responses to the data request accumulated since the last communication session. In case of fault or alarm condition in the mobile station, a local claim is activated and immediately initiates communication with the via cellular communication network. (authors)

Flight, orientation, and homing abilities of honeybees following exposure to 2.45-GHz CW microwaves.

Science.gov (United States)

Gary, N E; Westerdahl, B B

1981-01-01

Foraging-experienced honeybees retained normal flight, orientation, and memory functions after 30 minutes' exposure to 2.45-GHz CW microwaves at power densities from 3 to 50 mW/cm2. These experiments were conducted at power densities approximating and exceeding those that would be present above receiving antennas of the proposed solar power satellite (SPS) energy transmission system and for a duration exceeding that which honeybees living outside a rectenna might be expected to spend within the rectenna on individual foraging trips. There was no evidence that airborne invertebrates would be significantly affected during transient passage through microwaves associated with SPS ground-based microwave receiving stations.

Formation of trans-2-[4-(Dimethylamino)Styryl]-3-Ethyl-1,3-Benzothiazolium Perchlorate Dimers in the Presence of Sodium Polystyrene Sulfonate

Science.gov (United States)

Lavysh, A. V.; Maskevich, A. A.; Lugovskii, A. A.; Voropai, E. S.; Sulatskaya, A. I.; Kuznetsova, I. M.; Turoverov, K. K.

2017-01-01

The spectral properties of a novel thioflavin T derivative, trans-2-[4-(dimethylamino)styryl]-3-ethyl-1,3-benzothiazolium perchlorate (DMASEBT), were studied in aqueous solutions in the presence of sodium polystyrene sulfonate (SPS). It was shown that SPS either could interact with dye monomers or initiate the formation of non-fluorescent dye dimers depending on the concentration ratio of dye and polyelectrolyte. DMASEBT dimer formation in the presence of SPS produced a hypsochromic shift by 40 nm in the absorption spectrum and quenched fluorescence. A bathochromic shift of the absorption spectrum and an increase of the fluorescence intensity by an order of magnitude were observed if DMASEBT monomers interacted with SPS. Quantum-chemical analysis found that sandwich dimers (H-aggregates) were most stable. A comparison of DMASEBT spectra in the presence of SPS and amyloid fibrils showed that DMASEBT molecules were incorporated into amyloid fibrils as monomers. The spectral changes associated with this incorporation could not be explained by the formation of dye aggregates.

ICARUS-NESSiE: a sensitive search for sterile neutrinos at CERN SPS

Science.gov (United States)

Guglielmi, A.

2013-10-01

A new experimental search for sterile neutrinos beyond the Standard Model at a new CERN-SPS neutrino beam aiming at measuring the electron and muon neutrino events with a Near and Far detectors (1600 and 330 m from the proton target) is presented. The project will exploit the ICARUS T600 LAr-TPC moved from LNGS to the CERN Far position and a new additional LAr-TPC detector, 1/4 of the T600, located in the Near position. Two magnetic spectrometers will be placed downstream of the two LAr-TPC detectors to greatly complement the physics capabilities. Comparing the two detectors, in absence of oscillations, all cross sections and experimental biases cancel out. Any difference of the event distributions at the two locations should be attributed to the possible existence of oscillations, presumably due to additional neutrinos with a mixing angle sin2(2θnew) and a mass squared difference Δm2new larger than the measured for the standard neutrinos. The superior quality of the LAr imaging TPC, in particular its unique electron-π0 discrimination allows for full rejection of backgrounds and offers a lossless νe detection capability. The determination of the muon charge with the spectrometers allows for the full separation of νμ from bar nuμ and therefore controlling systematics from muon mis-identification mainly at high momenta.

CDIP Station Data Collection - All Stations

Data.gov (United States)

Scripps Institution of Oceanography, UC San Diego — The Coastal Data Information Program's station data collection consists of all publicly-released coastal environment measurements taken over the program's history, a...

A facility to Search for Hidden Particles at the CERN SPS: the SHiP physics case

CERN Document Server

Alekhin, Sergey; Asaka, Takehiko; Batell, Brian; Bezrukov, Fedor; Bondarenko, Kyrylo; Boyarsky, Alexey; Choi, Ki-Young; Corral, Cristobal; Craig, Nathaniel; Curtin, David; Davidson, Sacha; de Gouvea, Andre; Dell'Oro, Stefano; deNiverville, Patrick; Bhupal Dev, P.S.; Dreiner, Herbi; Drewes, Marco; Eijima, Shintaro; Essig, Rouven; Fradette, Anthony; Garbrecht, Bjorn; Gavela, Belen; Giudice, Gian F.; Goodsell, Mark D.; Gorbunov, Dmitry; Gori, Stefania; Grojean, Christophe; Guffanti, Alberto; Hambye, Thomas; Hansen, Steen H.; Helo, Juan Carlos; Hernandez, Pilar; Ibarra, Alejandro; Ivashko, Artem; Izaguirre, Eder; Jaeckel, Joerg; Jeong, Yu Seon; Kahlhoefer, Felix; Kahn, Yonatan; Katz, Andrey; Kim, Choong Sun; Kovalenko, Sergey; Krnjaic, Gordan; Lyubovitskij, Valery E.; Marcocci, Simone; Mccullough, Matthew; McKeen, David; Mitselmakher, Guenakh; Moch, Sven-Olaf; Mohapatra, Rabindra N.; Morrissey, David E.; Ovchynnikov, Maksym; Paschos, Emmanuel; Pilaftsis, Apostolos; Pospelov, Maxim; Reno, Mary Hall; Ringwald, Andreas; Ritz, Adam; Roszkowski, Leszek; Rubakov, Valery; Ruchayskiy, Oleg; Schienbein, Ingo; Schmeier, Daniel; Schmidt-Hoberg, Kai; Schwaller, Pedro; Senjanovic, Goran; Seto, Osamu; Shaposhnikov, Mikhail; Shchutska, Lesya; Shelton, Jessie; Shrock, Robert; Shuve, Brian; Spannowsky, Michael; Spray, Andy; Staub, Florian; Stolarski, Daniel; Strassler, Matt; Tello, Vladimir; Tramontano, Francesco; Tripathi, Anurag; Tulin, Sean; Vissani, Francesco; Winkler, Martin W.; Zurek, Kathryn M.; CERN. Geneva. SPS and PS Experiments Committee; SPSC

2016-10-24

This paper describes the physics case for a new fixed target facility at CERN SPS. The SHiP (Search for Hidden Particles) experiment is intended to hunt for new physics in the largely unexplored domain of very weakly interacting particles with masses below the Fermi scale, inaccessible to the LHC experiments, and to study tau neutrino physics. The same proton beam setup can be used later to look for decays of tau-leptons with lepton flavour number non-conservation, $\\tau\\to 3\\mu$ and to search for weakly-interacting sub-GeV dark matter candidates. We discuss the evidence for physics beyond the Standard Model and describe interactions between new particles and four different portals - scalars, vectors, fermions or axion-like particles. We discuss motivations for different models, manifesting themselves via these interactions, and how they can be probed with the SHiP experiment and present several case studies. The prospects to search for relatively light SUSY and composite particles at SHiP are also discussed....

A customer-friendly Space Station

Science.gov (United States)

Pivirotto, D. S.

1984-01-01

This paper discusses the relationship of customers to the Space Station Program currently being defined by NASA. Emphasis is on definition of the Program such that the Space Station will be conducive to use by customers, that is by people who utilize the services provided by the Space Station and its associated platforms and vehicles. Potential types of customers are identified. Scenarios are developed for ways in which different types of customers can utilize the Space Station. Both management and technical issues involved in making the Station 'customer friendly' are discussed.

The Miksova water power station

International Nuclear Information System (INIS)

2005-01-01

This leaflet describes the Miksova water power station. The Miksova water power station is part of the second derived cascade of hydro power stations on the river Vah. It was built at the end of a huge development in Slovak hydro-energy in the late 1950's and the beginning of the 1960's. It is the second water power station on this derived cascade, which is situated downstream the Hricov reservoir and water power station. At the power station, three turbine sets with vertical Kaplan turbines are installed with a total power output of 3 x 31.2 = 93.6 MW. With this power output the Miksova water power station (Miksova I) was the biggest water power station in the Slovak Republic until the construction of Pumping water power station Liptovska Mara. And it is still the biggest channel water power station on the Vah so far. It was put into operation during the period 1963 to 1965. There are three turbine sets with Kaplan turbines from CKD Blansko, with a synchronous hydro-alternator installed in the power station. Their installed capacity is 93.6 MW in total and the projected annual production of electrical energy is 207 GWh. The turbines are fi ve-bladed (on the Hricov and Povazska Bystrica water power stations they are four-bladed) and the impeller wheel has a diameter of 4800 mm. They are designed for extension of the head from 24.1 to 22.21 m and each of them has an absorption capacity of 134 m 3 .s -1 nd a nominal operating speed of 2.08 m 3 .s -1 , runaway speed 4.9 m 3 .s -1 . Each synchronous hydro-alternator has a maximum power output of 31.2 MW, a nominal voltage of 10.5 kV and power factor cos φ of 0.8. Power from the power station is led out through 110 kV switchgear. The water power station operates under automatic turbine mode of operation with remote indication and control from the Dispatch Centre at Vodne elektrarne, in Trencin. From start of operation until the end of 2003 all three turbine sets operated for a total of 450,500 running hours and the

Construction of Kashiwazaki-Kariwa Nuclear Power Station Results of manufacturing concrete

International Nuclear Information System (INIS)

Morishita, Hideki; Tsuchiya, Yoshimasa; Eguchi, Kiyoshi; Hosaka, Hiroshi

1998-01-01

The construction of Kashiwazaki-Kariwa Nuclear Power Station of Tokyo Electric Power Co., Inc. was completed in July, 1997. Seven nuclear power plants generate about 8.2 million kW, and it is the largest nuclear power station in the world. In the construction, from May, 1980 to August, 1996, the concrete of 2.42 million m 3 for architecture and 1.04 million m 3 for civil engineering, 3.46 million m 3 in total, and the mortar for artificial rock bed of 430,000 m 3 were manufactured and placed. The results of manufacturing concrete from beginning to finish are shown. The specification of concrete was different for No. 1 plant, No. 2 and 5 plants, No. 3 and 4 plants and No. 6 and 7 plants. As to the mixing of concrete, the specification and the materials used are reported. The features of the facilities for manufacturing concrete are explained. The flowchart of the quality control of materials and concrete is shown. The material testing of cement and aggregate, the test of water quality and the material testing of admixtures were carried out. As for concrete, the weight of unit volume, slump, air quantity, concrete temperature, chloride content, strength and alkali reactivity were examined. (K.I.)

Space station propulsion requirements study

Science.gov (United States)

Wilkinson, C. L.; Brennan, S. M.

1985-01-01

Propulsion system requirements to support Low Earth Orbit (LEO) manned space station development and evolution over a wide range of potential capabilities and for a variety of STS servicing and space station operating strategies are described. The term space station and the overall space station configuration refers, for the purpose of this report, to a group of potential LEO spacecraft that support the overall space station mission. The group consisted of the central space station at 28.5 deg or 90 deg inclinations, unmanned free-flying spacecraft that are both tethered and untethered, a short-range servicing vehicle, and a longer range servicing vehicle capable of GEO payload transfer. The time phasing for preferred propulsion technology approaches is also investigated, as well as the high-leverage, state-of-the-art advancements needed, and the qualitative and quantitative benefits of these advancements on STS/space station operations. The time frame of propulsion technologies applicable to this study is the early 1990's to approximately the year 2000.

Hydrogen Station Cost Estimates: Comparing Hydrogen Station Cost Calculator Results with other Recent Estimates

Energy Technology Data Exchange (ETDEWEB)

Melaina, M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Penev, M. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2013-09-01

This report compares hydrogen station cost estimates conveyed by expert stakeholders through the Hydrogen Station Cost Calculation (HSCC) to a select number of other cost estimates. These other cost estimates include projections based upon cost models and costs associated with recently funded stations.

Gas Stations, US, 2010, NAVTEQ

Data.gov (United States)

U.S. Environmental Protection Agency — The Gas_Stations dataset is derived from the Navteq 'AUTOSVC' SDC layer (FAC_TYPE=5540) and contains gas stations and petrol stations. This NAVTEQ dataset is...

Non-Coop Station History (Unindexed)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Station history documentation for stations outside the US Cooperative Observer network. Documents should be compared with those in the Non-Coop Station History...

Single-Station Sigma for the Iranian Strong Motion Stations

Science.gov (United States)

Zafarani, H.; Soghrat, M. R.

2017-11-01

In development of ground motion prediction equations (GMPEs), the residuals are assumed to have a log-normal distribution with a zero mean and a standard deviation, designated as sigma. Sigma has significant effect on evaluation of seismic hazard for designing important infrastructures such as nuclear power plants and dams. Both aleatory and epistemic uncertainties are involved in the sigma parameter. However, ground-motion observations over long time periods are not available at specific sites and the GMPEs have been derived using observed data from multiple sites for a small number of well-recorded earthquakes. Therefore, sigma is dominantly related to the statistics of the spatial variability of ground motion instead of temporal variability at a single point (ergodic assumption). The main purpose of this study is to reduce the variability of the residuals so as to handle it as epistemic uncertainty. In this regard, it is tried to partially apply the non-ergodic assumption by removing repeatable site effects from total variability of six GMPEs driven from the local, Europe-Middle East and worldwide data. For this purpose, we used 1837 acceleration time histories from 374 shallow earthquakes with moment magnitudes ranging from M w 4.0 to 7.3 recorded at 370 stations with at least two recordings per station. According to estimated single-station sigma for the Iranian strong motion stations, the ratio of event-corrected single-station standard deviation ( Φ ss) to within-event standard deviation ( Φ) is about 0.75. In other words, removing the ergodic assumption on site response resulted in 25% reduction of the within-event standard deviation that reduced the total standard deviation by about 15%.

The Septum Magnet System of the New Fast Extraction Channel of the SPS at CERN

CERN Document Server

Balhan, B; Rizzo, A; Weterings, W

2004-01-01

In the Long Straight Section LSS4 of the Super Proton Synchrotron (SPS) at CERN, a new fast extraction system has been installed in order to extract the beam to ring 2 of the Large Hadron Collider (LHC) and the CERN Neutrino to Gran Sasso facility (CNGS). The system consists of horizontal closed orbit bumper magnets, extraction kicker magnets, enlarged aperture quadrupoles and six conventional DC electromagnetic septum magnets (MSE). A protection element (TPSG) has been placed immediately upstream of the first septum coil. The septum magnets and TPSG are mounted on a single mobile retractable support girder. The MSE septa are connected by a so-called plug-in system to a rigid water-cooled bus-bar, powered by water-cooled cables. The whole system is kept at the required vacuum pressure by ion pumps attached to separate pumping modules. In this note we present the design features and parameters of the MSE septum magnets, describe the function of the related main equipment elements, briefly report on the control...

Central Station Design Options

DEFF Research Database (Denmark)

2011-01-01

. The work identifies the architecture, sizing and siting of prospective Central Stations in Denmark, which can be located at shopping centers, large car parking lots or gas stations. Central Stations are planned to be integrated in the Danish distribution grid. The Danish island of Bornholm, where a high...... overloading, more reference points might be necessary to represent various transformer loading levels. The subject of safety in Central Station is also addressed. A number of safety rules based on European standards apply to AC charging equipment up to 44 kW. The connection interlock and the automatic de......-energization are identified as fundamental requirements for safety in such a charging station. The connection interlock is a solution which ensures that no power is applied to the DC cable when the EV connector is not connected. The automatic de-energization device ensures that whenever a strain on the cable is detected, e...

Enhanced Master Station History Report

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Enhanced Master Station History Report (EMSHR) is a compiled list of basic, historical information for every station in the station history database, beginning...

Topography and diffractometry station in synchrotron radiation beam of the VEPP-4 storage ring. Topography of garnets

International Nuclear Information System (INIS)

Kub, I.; Poltsarova, M.; Panchenko, V.E.

1987-01-01

Advantages of synchrotron radiation (SR) spectrum of the VEhPP-4 storage ring for X-ray topography and diffractometry are shown. The description of ''Topography and diffractometry'' station in SR dump station of the VEhPP storage ring is presented, peculiarities of X-ray topography method used are discussed. X-ray topographic images of gadolinium-gallium and manganese-germanium garnets taken on the VEhPP SR are given in comparison with conventional images taken using X-ray tubes and SR of the VEhPP-3 storage ring

47 CFR 97.109 - Station control.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 5 2010-10-01 2010-10-01 false Station control. 97.109 Section 97.109... SERVICE Station Operation Standards § 97.109 Station control. (a) Each amateur station must have at least one control point. (b) When a station is being locally controlled, the control operator must be at the...

Concurrent communication among multi-transceiver stations over shared media. Ph.D. Thesis

Science.gov (United States)

Birk, Yitzhak

1987-01-01

In order to increase a local-area network's throughput beyond a single bus data rate without using dedicated switching nodes, multiple buses and multitransceiver stations are required. The design space of single-hop interconnections is explored among such stations. Interconnections are presented whose throughput can grow quadratically with the number of transmitters and receivers per station. These are referred to as selective broadcast interconnections (SBIs). The performance of various SBIs are studied. A spread-spectrum channel can accommodate several current successful transmission, and a single-transceiver node can thus utilize only a small fraction of the channel capacity. In order to allocate the appropriate fraction of capacity to a busy node, it is proposed to equip it with several transmitters and receivers, thereby turning it into a supernode. Several architectures and operation policies for supernodes are suggested and compared. It is shown that a supernode can significantly outperform a collection of independent conventional nodes with the same total numbers of transmitters and receivers. Packet-radio networks with half-duplex nodes, as well as networks with full-duplex nodes, are considered.

Study of the production of {phi}, {rho}, {omega} mesons in the ultra-relativistic heavy ion collisions at the SPS of CERN; Etude de la production des mesons {phi}, {rho} et {omega} dans les collisions d'ions lourds ultra-relativistes au SPS du CERN (dans l'experience NA50)

Energy Technology Data Exchange (ETDEWEB)

Villatte, L

2001-03-28

The NA50 experiment is one of the experiment using the SPS (Super Proton Synchrotron) beam at CERN (european laboratory for particle physics). One of the common aim of the SPS experiment is to look for the existence of a new state of the nuclear matter: the quark-gluon plasma. Among the proposed signatures of the quark-gluon plasma is the enhanced production of particles containing strange quarks. In the current work, the NA50/NA38 experiment data are analysed and the relative production of the {phi} and {rho} + {omega} mesons are obtained from Pb-Pb collisions at 158 and S-U at 200 GeV per nucleon. The measured ({phi}/({rho} +{omega})){mu}{mu} ratio as a function of the transverse mass does not present any unexpected behavior, however, central collisions as compared to peripheral collisions show an increase by a factor 1.7. The {phi} and {rho}+{omega} multiplicities are extracted for the Pb-Pb collisions and show that the enhancement of the ({phi}/({rho}+{omega})){mu}{mu} ratio is due to the {phi} meson production increase. The evolution of the {phi} meson multiplicity, versus the number of participant nucleus (N{sub part}), is different from that of the multi-strange baryons. The effective temperatures are deduced from the study of the {phi} and {rho} + {omega} production cross sections with respect to the transverse mass and compared to those obtained by other experiments and other particles. An additional study is done to extract the K/{pi} ratio versus N{sub part}. (authors)

Power station instrumentation

International Nuclear Information System (INIS)

Jervis, M.W.

1993-01-01

Power stations are characterized by a wide variety of mechanical and electrical plant operating with structures, liquids and gases working at high pressures and temperatures and with large mass flows. The voltages and currents are also the highest that occur in most industries. In order to achieve maximum economy, the plant is operated with relatively small margins from conditions that can cause rapid plant damage, safety implications, and very high financial penalties. In common with other process industries, power stations depend heavily on control and instrumentation. These systems have become particularly significant, in the cost-conscious privatized environment, for providing the means to implement the automation implicit in maintaining safety standards, improving generation efficiency and reducing operating manpower costs. This book is for professional instrumentation engineers who need to known about their use in power stations and power station engineers requiring information about the principles and choice of instrumentation available. There are 8 chapters; chapter 4 on instrumentation for nuclear steam supply systems is indexed separately. (Author)

SP and KLF Transcription Factors in Digestive Physiology and Diseases.

Science.gov (United States)

Kim, Chang-Kyung; He, Ping; Bialkowska, Agnieszka B; Yang, Vincent W

2017-06-01

Specificity proteins (SPs) and Krüppel-like factors (KLFs) belong to the family of transcription factors that contain conserved zinc finger domains involved in binding to target DNA sequences. Many of these proteins are expressed in different tissues and have distinct tissue-specific activities and functions. Studies have shown that SPs and KLFs regulate not only physiological processes such as growth, development, differentiation, proliferation, and embryogenesis, but pathogenesis of many diseases, including cancer and inflammatory disorders. Consistently, these proteins have been shown to regulate normal functions and pathobiology in the digestive system. We review recent findings on the tissue- and organ-specific functions of SPs and KLFs in the digestive system including the oral cavity, esophagus, stomach, small and large intestines, pancreas, and liver. We provide a list of agents under development to target these proteins. Copyright © 2017 AGA Institute. Published by Elsevier Inc. All rights reserved.

Station Capacity

DEFF Research Database (Denmark)

Landex, Alex

2011-01-01

the probability of conflicts and the minimum headway times into account. The last method analyzes how optimal platform tracks are used by examining the arrival and departure pattern of the trains. The developed methods can either be used separately to analyze specific characteristics of the capacity of a station......Stations are often limiting the capacity of railway networks. This is due to extra need of tracks when trains stand still, trains turning around, and conflicting train routes. Although stations are often the capacity bottlenecks, most capacity analysis methods focus on open line capacity. Therefore...... for platform tracks and the probability that arriving trains will not get a platform track immediately at arrival. The third method is a scalable method that analyzes the conflicts in the switch zone(s). In its simplest stage, the method just analyzes the track layout while the more advanced stages also take...

Conducting Integrated Objective Structured Clinical Examination: Experiences at KIST Medical College, Nepal

Directory of Open Access Journals (Sweden)

Rano Mal Piryani

2013-01-01

Full Text Available Background: Objective structured clinical examination (OSCE, an important tool for assessment of clinical skills, introduced more than 4 decades ago. KIST Medical College, a new medical school of Nepal, affiliated to Tribhuvan University Institute of Medicine, has made learning of physical examination skills structured and integrated with greater involvement of different clinical science departments. Students learn physical examination skills in second year MBBS as a part of early clinical exposure. Objective: To share the experiences regarding implementation of integrated OSCE. Materials and Methods: At the end of clinical posting of learning of physical examination skills, assessment was done with OSCE. Fifteen OSCE stations including each of 5 minutes were developed and arranged. Standardized patients and validated checklist were used. OSCE was conducted in novel way. Prior to the OSCE session: Suitable venue was selected, assessors were identified, standardized patients were selected, running order of the stations in circuit was developed, list of equipments/instruments required was prepared, and tasks, checklists, feedback questionnaires were printed. The day before the OSCE session: OSCE stations were inspected and clearly labeled, condition of required equipments/instruments was checked, a pack of the documents for each OSCE station were made available, and signs were displayed at proper places. On the day of the OSCE session: Reliable stop watch and loud manual bell were used, support staffs were placed to direct the candidates, examiners, and standardized patients (SPs, assessors explained SPs, students were briefed, supervisors observed the session, and feedback were taken from students, assessors, and SPs. At the end of the OSCE session: Checklists and feedback questionnaires were collected, token money was paid to SPs, and a contribution of everyone was appreciated. After the OSCE session: Score was compiled and result declared, and

Level of service for pedestrian movement towards the performance of passenger information in public transport stations in Klang Valley

Science.gov (United States)

Ramli, M. Z.; Hanipah, M. H.; Lee, L. G.; Loo, K. F.; Wong, J. K.; Zawawi, M. H.; Fuad, N. F. S.

2017-09-01

Rapid growth in car ownership in Malaysia plays a major role to traffic congestion. Hence, public transportation is crucial to cater the residents in high-density area especially in Klang Valley. Signage information in public transport station is one of an important passenger information system. Poor placement of sign information will decrease the efficiency of passenger flow and caused congestion in the station. Passenger information system is very useful for trip planning and decision making. Therefore, it is interesting to study the performance of passenger information system in focusing the movement behavior of pedestrian at non-peak period. Thus, the study on pedestrian movement during non-peak period on weekdays and weekends in mass transit stations and bus transit stations in Klang Valley was carried out by using video observation. The observation of the pedestrian movement was made in Mass Transit Station 1 in the middle of Kuala Lumpur and Mass Transit Station 2 in southern of Kuala Lumpur. The other site was focused at Bus Transit Station 1 in Putrajaya and Bus Transit Station 2 in Kajang. Findings shown that Mass Transit Station 1 having the best facility in terms of passenger information which the level of service obtained is LOS A, while the lowest level of service which is LOS E was obtained in Bus Transit Station 2.

Secure base stations

NARCIS (Netherlands)

Bosch, Peter; Brusilovsky, Alec; McLellan, Rae; Mullender, Sape J.; Polakos, Paul

2009-01-01

With the introduction of the third generation (3G) Universal Mobile Telecommunications System (UMTS) base station router (BSR) and fourth generation (4G) base stations, such as the 3rd Generation Partnership Project (3GPP) Long Term Evolution (LTE) Evolved Node B (eNB), it has become important to

Data communications method for mobile network in fourth generation communications system, involves delivering decoded data to mobile station from relay station, where mobile station receives data from both relay and base stations

DEFF Research Database (Denmark)

2008-01-01

The method involves utilizing a base station (BS) (100) to transmit data to a relay station (RS) (110) and a mobile station (MS) (120), where the data includes two messages. The BS is utilized to transmit the two messages by utilizing a linear combination method, and the data is received in the RS...

Glycyrrhizin Treatment Facilitates Extinction of Conditioned Fear Responses After a Single Prolonged Stress Exposure in Rats

Directory of Open Access Journals (Sweden)

Shuhua Lai

2018-03-01

Full Text Available Background/Aims: Impaired fear memory extinction is widely considered a key mechanism of post-traumatic stress disorder (PTSD. Recent studies have suggested that neuroinflammation after a single prolonged stress (SPS exposure may play a critical role in the impaired fear memory extinction. Studies have shown that high mobility group box chromosomal protein 1 (HMGB-1 is critically involved in neuroinflammation. However, the role of HMGB-1 underlying the development of impairment of fear memory extinction is still not known. Methods: Thus, we examined the levels of HMGB-1 in the basolateral amygdala (BLA following SPS using Western blot and evaluated the levels of microglia and astrocytes activation in the BLA after SPS using immunohistochemical staining. We then examined the effects of pre-SPS intra-BLA administration of glycyrrhizin, an HMGB1 inhibitor, or LPS-RS, a competitive TLR4 antagonist, on subsequent post-SPS fear extinction. Results: We found that SPS treatment prolonged the extinction of contextual fear memory after the SPS. The impairment of SPS-induced extinction of contextual fear memory was associated with increased HMGB1 and Toll-like receptor 4 (TLR4 levels in the BLA. Additionally, the impairment of SPS-induced extinction of contextual fear memory was associated with increased activation of microglia and astrocyte in the BLA. Intra-BLA administrations of glycyrrhizin (HMGB-1 inhibitor or LPS-RS (TLR4 antagonist can prevent the development of SPS-induced fear extinction impairment. Conclusion: Taken together, these results suggested that SPS treatment may not only produce short term effects on the HMGB1/TLR4-mediated pro-inflammation, but alter the response of microglia and astrocytes to the exposure to fear associated contextual stimuli.

Glycyrrhizin Treatment Facilitates Extinction of Conditioned Fear Responses After a Single Prolonged Stress Exposure in Rats.

Science.gov (United States)

Lai, Shuhua; Wu, Gangwei; Jiang, Zhixian

2018-01-01

Impaired fear memory extinction is widely considered a key mechanism of post-traumatic stress disorder (PTSD). Recent studies have suggested that neuroinflammation after a single prolonged stress (SPS) exposure may play a critical role in the impaired fear memory extinction. Studies have shown that high mobility group box chromosomal protein 1 (HMGB-1) is critically involved in neuroinflammation. However, the role of HMGB-1 underlying the development of impairment of fear memory extinction is still not known. Thus, we examined the levels of HMGB-1 in the basolateral amygdala (BLA) following SPS using Western blot and evaluated the levels of microglia and astrocytes activation in the BLA after SPS using immunohistochemical staining. We then examined the effects of pre-SPS intra-BLA administration of glycyrrhizin, an HMGB1 inhibitor, or LPS-RS, a competitive TLR4 antagonist, on subsequent post-SPS fear extinction. We found that SPS treatment prolonged the extinction of contextual fear memory after the SPS. The impairment of SPS-induced extinction of contextual fear memory was associated with increased HMGB1 and Toll-like receptor 4 (TLR4) levels in the BLA. Additionally, the impairment of SPS-induced extinction of contextual fear memory was associated with increased activation of microglia and astrocyte in the BLA. Intra-BLA administrations of glycyrrhizin (HMGB-1 inhibitor) or LPS-RS (TLR4 antagonist) can prevent the development of SPS-induced fear extinction impairment. Taken together, these results suggested that SPS treatment may not only produce short term effects on the HMGB1/TLR4-mediated pro-inflammation, but alter the response of microglia and astrocytes to the exposure to fear associated contextual stimuli. © 2018 The Author(s). Published by S. Karger AG, Basel.

Environmental assessment for the satellite power system concept development and evaluation program: nonmicrowave health and ecological effects

Energy Technology Data Exchange (ETDEWEB)

White, M R

1980-11-01

A Concept Development and Evaluation Program is being carried out for a proposed Satellite Power System (SPS). For purposes of this evaluation, a preliminary reference system has been developed. SPS, as described in the reference system, would collect solar energy on satellites in geosychronous orbit in space. The energy would be converted to microwaves and beamed to an earth-receiving antenna (rectenna). One task in the environmental part of the program is the assessment of the nonmicrowave effects on health and the environment. These effects would result from all phases of SPS development and operation. This report covers the current knowledge regarding these effects, and is based on the reference system. The assessment is summarized as to scope, methodology, impacts of terrestrial development, launch and recovery of spacecraft, space activities (including health effects of the space environment, ionizing radiation, electromagnetic exposure, spacecraft charging and environmental interactions, occupational hazards, etc.) and construction and operation of rectenna (ground receiving station).

Waste Transfer Stations

DEFF Research Database (Denmark)

Christensen, Thomas Højlund

2011-01-01

tion and transport is usually the most costly part of any waste management system; and when waste is transported over a considerable distance or for a long time, transferring the waste from the collection vehicles to more efficient transportation may be economically beneficial. This involves...... a transfer station where the transfer takes place. These stations may also be accessible by private people, offering flexibility to the waste system, including facilities for bulky waste, household hazardous waste and recyclables. Waste transfer may also take place on the collection route from small...... describes the main features of waste transfer stations, including some considerations about the economical aspects on when transfer is advisable....

Meyrin Petrol Station

CERN Multimedia

2006-01-01

Please note that the Meyrin petrol station will be closed for maintenance work on Tuesday 19 and Wednesday 20 December 2006. If you require petrol during this period we invite you to use the Prévessin petrol station, which will remain open. TS-IC-LO Section Tel.: 77039 - 73793

Radiation observation at Dome Fuji Station, Antarctica

Directory of Open Access Journals (Sweden)

Naohiko Hirasawa

2008-06-01

Full Text Available This paper reports radiation observations at Dome Fuji Station from February 1, 2003 to January 20, 2004, carried out by the 44th Japanese Antarctic Research Expedition team. The radiometers which measured the upward longwave radiation (LWu, the downward longwave (LWd and the downward shortwave (SWd were equipped with fans to avoid frosting on the surface of the radiometer dome by air circulation. The upward shortwave radiation (SWu measured by a radiometer without fan needs correction, which we leave as a problem for the future. In addition, as for LWd and LWu in the polar night, a typical radiational cooling case and a suppressed radiational cooling one are shown.

Base Station Performance Model

OpenAIRE

Walsh, Barbara; Farrell, Ronan

2005-01-01

At present the testing of power amplifiers within base station transmitters is limited to testing at component level as opposed to testing at the system level. While the detection of catastrophic failure is possible, that of performance degradation is not. This paper proposes a base station model with respect to transmitter output power with the aim of introducing system level monitoring of the power amplifier behaviour within the base station. Our model reflects the expe...

Space Station fluid management logistics

Science.gov (United States)

Dominick, Sam M.

1990-01-01

Viewgraphs and discussion on space station fluid management logistics are presented. Topics covered include: fluid management logistics - issues for Space Station Freedom evolution; current fluid logistics approach; evolution of Space Station Freedom fluid resupply; launch vehicle evolution; ELV logistics system approach; logistics carrier configuration; expendable fluid/propellant carrier description; fluid carrier design concept; logistics carrier orbital operations; carrier operations at space station; summary/status of orbital fluid transfer techniques; Soviet progress tanker system; and Soviet propellant resupply system observations.

Hammond Bay Biological Station

Data.gov (United States)

Federal Laboratory Consortium — Hammond Bay Biological Station (HBBS), located near Millersburg, Michigan, is a field station of the USGS Great Lakes Science Center (GLSC). HBBS was established by...

47 CFR 74.793 - Digital low power TV and TV translator station protection of broadcast stations.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Digital low power TV and TV translator station... DISTRIBUTIONAL SERVICES Low Power TV, TV Translator, and TV Booster Stations § 74.793 Digital low power TV and TV translator station protection of broadcast stations. (a) An application to construct a new digital low power...

A Bayesian analysis of trends in ozone sounding data series from 9 Nordic stations

Science.gov (United States)

Christiansen, Bo; Jepsen, Nis; Larsen, Niels; Korsholm, Ulrik S.

2016-04-01

Ozone soundings from 9 Nordic stations have been homogenized and interpolated to standard pressure levels. The different stations have very different data coverage; the longest period with data is from the end of the 1980ies to 2013. We apply a model which includes both low-frequency variability in form of a polynomial, an annual cycle with harmonics, the possibility for low-frequency variability in the annual amplitude and phasing, and either white noise or AR1 noise. The fitting of the parameters is performed with a Bayesian approach not only giving the posterior mean values but also credible intervals. We find that all stations agree on an well-defined annual cycle in the free troposphere with a relatively confined maximum in the early summer. Regarding the low-frequency variability we find that Scoresbysund, Ny Aalesund, and Sodankyla show similar structures with a maximum near 2005 followed by a decrease. However, these results are only weakly significant. A significant change in the amplitude of the annual cycle was only found for Ny Aalesund. Here the peak-to-peak amplitude changes from 0.9 to 0.8 mhPa between 1995-2000 and 2007-2012. The results are shown to be robust to the different settings of the model parameters (order of the polynomial, number of harmonics in the annual cycle, type of noise, etc). The results are also shown to be characteristic for all pressure levels in the free troposphere.

Big Game Reporting Stations

Data.gov (United States)

Vermont Center for Geographic Information — Point locations of big game reporting stations. Big game reporting stations are places where hunters can legally report harvested deer, bear, or turkey. These are...

Weigh-in-Motion Stations

Data.gov (United States)

Department of Homeland Security — The data included in the GIS Traffic Stations Version database have been assimilated from station description files provided by FHWA for Weigh-in-Motion (WIM), and...

Air and radiation monitoring stations

CERN Multimedia

AUTHOR|(SzGeCERN)582709

2015-01-01

CERN has around 100 monitoring stations on and around its sites. New radiation measuring stations, capable of detecting even lower levels of radiation, were installed in 2014. Two members of HE-SEE group (Safety Engineering and Environment group) in front of one of the new monitoring stations.

47 CFR 73.1120 - Station location.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Station location. 73.1120 Section 73.1120... Rules Applicable to All Broadcast Stations § 73.1120 Station location. Each AM, FM, TV and Class A TV... be the geographical station location. [65 FR 30003, May 10, 2000] ...

Water Level Station History

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Images contain station history information for 175 stations in the National Water Level Observation Network (NWLON). The NWLON is a network of long-term,...

Local society and nuclear power stations

International Nuclear Information System (INIS)

1984-02-01

This report was made by the expert committee on region investigation, Japan Atomic Industrial Forum Inc., in fiscal years 1981 and 1982 in order to grasp the social economic influence exerted on regions by the location of nuclear power stations and the actual state of the change due to it, and to search for the way the promotion of local community should be. The influence and the effect were measured in the regions around the Fukushima No. 1 Nuclear Power Station of Tokyo Electric Power Co., Inc., the Mihama Power Station of Kansai Electric Power Co., Inc., and the Genkai Nuclear Power Station of Kyushu Electric Power Co., Inc. The fundamental recognition in this discussion, the policy of locating nuclear power stations and the management of regions, the viewpoint and way of thinking in the investigation of the regions where nuclear power stations are located, the actual state of social economic impact due to the location of nuclear power stations, the connected mechanism accompanying the location of nuclear power stations, and the location of nuclear power stations and the acceleration of planning for regional promotion are reported. In order to economically generate electric power, the rationalization in the location of nuclear power stations is necessary, and the concrete concept of building up local community must be decided. (Kako, I.)

47 CFR 25.137 - Application requirements for earth stations operating with non-U.S. licensed space stations.

Science.gov (United States)

2010-10-01

... space stations. (a) Earth station applicants or entities filing a “letter of intent” or “Petition for... Union. (d) Earth station applicants requesting authority to operate with a non-U.S.-licensed space... 47 Telecommunication 2 2010-10-01 2010-10-01 false Application requirements for earth stations...

Effect of Suspension Plasma-Sprayed YSZ Columnar Microstructure and Bond Coat Surface Preparation on Thermal Barrier Coating Properties

Science.gov (United States)

Bernard, Benjamin; Quet, Aurélie; Bianchi, Luc; Schick, Vincent; Joulia, Aurélien; Malié, André; Rémy, Benjamin

2017-08-01

Suspension plasma spraying (SPS) is identified as promising for the enhancement of thermal barrier coating (TBC) systems used in gas turbines. Particularly, the emerging columnar microstructure enabled by the SPS process is likely to bring about an interesting TBC lifetime. At the same time, the SPS process opens the way to a decrease in thermal conductivity, one of the main issues for the next generation of gas turbines, compared to the state-of-the-art deposition technique, so-called electron beam physical vapor deposition (EB-PVD). In this paper, yttria-stabilized zirconia (YSZ) coatings presenting columnar structures, performed using both SPS and EB-PVD processes, were studied. Depending on the columnar microstructure readily adaptable in the SPS process, low thermal conductivities can be obtained. At 1100 °C, a decrease from 1.3 W m-1 K-1 for EB-PVD YSZ coatings to about 0.7 W m-1 K-1 for SPS coatings was shown. The higher content of porosity in the case of SPS coatings increases the thermal resistance through the thickness and decreases thermal conductivity. The lifetime of SPS YSZ coatings was studied by isothermal cyclic tests, showing equivalent or even higher performances compared to EB-PVD ones. Tests were performed using classical bond coats used for EB-PVD TBC coatings. Thermal cyclic fatigue performance of the best SPS coating reached 1000 cycles to failure on AM1 substrates with a β-(Ni,Pt)Al bond coat. Tests were also performed on AM1 substrates with a Pt-diffused γ-Ni/γ'-Ni3Al bond coat for which more than 2000 cycles to failure were observed for columnar SPS YSZ coatings. The high thermal compliance offered by both the columnar structure and the porosity allowed the reaching of a high lifetime, promising for a TBC application.

Human-factor operating concept for Borssele Nuclear Power Station

International Nuclear Information System (INIS)

Wieman, J.L.

1995-01-01

The safety level in the operation of a reactor is determined basically by human beings. The Borssele Nuclear Power Station has carried out measures for improving the man-machine interface through training and operating instructions for the shift personnel. The retrofitting of control technology relevant to safety engineering should avoid operating instructions which can cause potential failures. A safety study has shown that the remaining risk following all retrofitting measures remains dependent to the extent of 80% on human factors and that human factors as a whole have a positive effect on reactor safety. (orig.) [de