WorldWideScience

Sample records for standard problem procedures

  1. CSNI international standard problem procedures - CSNI Report No. 17 - Revision 4

    International Nuclear Information System (INIS)

    Micaelli, J.C.

    2004-01-01

    . Careful consideration and planning is therefore required. After a brief recall of the ISPs' objectives, this document provides guidelines to be followed during the different phases of an ISP. Two phases are considered. The first one consists in proposing and selecting an ISP, the second one consists in performing an ISP. This revised document was prepared under the Leadership of J.-C. Micaelli (IRSN). It was reviewed and endorsed in September 2003 by the Working Group on the Analysis and Management of Accidents (GAMA), GAMA performed in 2003 a survey on updating CSNI Report No. 17, 'CSNI Standard Problem Procedures', first published in 1977, last updated in 1989. The objective of this activity was to collect proposals regarding the improvement of ISP efficiency with respect to their objectives and the improvement of the quality of the procedures document. Eleven series of questions were asked in the survey, related to: - General structure of the procedures document; - ISP objectives; - Six phases: ISP proposal, ISP specification, ISP results reporting, Preparation of the preliminary data comparison and interpretation report, Post-ISP analysis, Preparation of the final comparison and interpretation report; - Updating of the procedures; - Support to be provided by the participants

  2. Radiation control standards and procedures

    Energy Technology Data Exchange (ETDEWEB)

    1956-12-14

    This manual contains the Radiation Control Standards'' and Radiation Control Procedures'' at Hanford Operations which have been established to provide the necessary control radiation exposures within Irradiation Processing Department. Provision is also made for including, in the form of Bulletins'', other radiological information of general interest to IPD personnel. The purpose of the standards is to establish firm radiological limits within which the Irradiation Processing Department will operate, and to outline our radiation control program in sufficient detail to insure uniform and consistent application throughout all IPD facilities. Radiation Control Procedures are intended to prescribe the best method of accomplishing an objective within the limitations of the Radiation Control Standards. A procedure may be changed at any time provided the suggested changes is generally agreeable to management involved, and is consistent with department policies and the Radiation Control Standards.

  3. Authentication: A Standard Problem or a Problem of Standards?

    Directory of Open Access Journals (Sweden)

    Amanda Capes-Davis

    2016-06-01

    Full Text Available Reproducibility and transparency in biomedical sciences have been called into question, and scientists have been found wanting as a result. Putting aside deliberate fraud, there is evidence that a major contributor to lack of reproducibility is insufficient quality assurance of reagents used in preclinical research. Cell lines are widely used in biomedical research to understand fundamental biological processes and disease states, yet most researchers do not perform a simple, affordable test to authenticate these key resources. Here, we provide a synopsis of the problems we face and how standards can contribute to an achievable solution.

  4. German standard problem No. 2

    International Nuclear Information System (INIS)

    Burkhardt, R.

    1980-02-01

    The German Standard Problem Nr. 2 (primary circuits) is meant to check whether the presently available computing programs dealing with ECCS problems are suitable to reflect with sufficient accuracy reload and flooding processes. Changing from conventional calculation methods to the ''best-estimate'' method requires for possibility of exact comparison, as is the case here because of experimental results from the primary circuit test plant. The test plant of KWU Erlangen with primary circuit modeups on a 1:134 scale with exact level indications allows comparative testing where emergency cooling water is loaded into the system filled with saturated steam over cold lanes, or rather over the annulus modeup. The report on hand goes into detail about calculations, anticipated results and their comparison to experimental results. (orig./RW) [de

  5. Standardized procedure for tsunami PRA by AESJ

    International Nuclear Information System (INIS)

    Kirimoto, Yukihiro; Yamaguchi, Akira; Ebisawa, Katsumi

    2013-01-01

    After Fukushima Accident (March 11, 2011), the Atomic Energy Society of Japan (AESJ) started to develop the standard of Tsunami Probabilistic Risk Assessment (PRA) for nuclear power plants in May 2011. As Japan is one of the countries with frequent earthquakes, a great deal of efforts has been made in the field of seismic research since the early stage. To our regret, the PRA procedures guide for tsunami has not yet been developed although the importance is held in mind of the PRA community. Accordingly, AESJ established a standard to specify the standardized procedure for tsunami PRA considering the results of investigation into the concept, the requirements that should have and the concrete methods regarding tsunami PRA referring the opinions of experts in the associated fields in December 2011 (AESJ-SC-RK004:2011). (author)

  6. The Problem of National Standards.

    Science.gov (United States)

    Brannon, Lil

    1995-01-01

    Argues that the development of national standards is another way in which the literacy crisis is being managed and maintained, a crisis arising from the tension between America's promise to the individual that he or she will have full access to intellectual resources and the needs of capitalism to have a differentiated, stratified workforce. (TB)

  7. Fault estimation - A standard problem approach

    DEFF Research Database (Denmark)

    Stoustrup, J.; Niemann, Hans Henrik

    2002-01-01

    This paper presents a range of optimization based approaches to fault diagnosis. A variety of fault diagnosis problems are reformulated in the so-called standard problem set-up introduced in the literature on robust control. Once the standard problem formulations are given, the fault diagnosis...... problems can be solved by standard optimization techniques. The proposed methods include (1) fault diagnosis (fault estimation, (FE)) for systems with model uncertainties; FE for systems with parametric faults, and FE for a class of nonlinear systems. Copyright...

  8. Standardized Definitions for Code Verification Test Problems

    Energy Technology Data Exchange (ETDEWEB)

    Doebling, Scott William [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-09-14

    This document contains standardized definitions for several commonly used code verification test problems. These definitions are intended to contain sufficient information to set up the test problem in a computational physics code. These definitions are intended to be used in conjunction with exact solutions to these problems generated using Exact- Pack, www.github.com/lanl/exactpack.

  9. 18 CFR 725.6 - Principles, standards and procedures.

    Science.gov (United States)

    2010-04-01

    ... 18 Conservation of Power and Water Resources 2 2010-04-01 2010-04-01 false Principles, standards... Responsibilities § 725.6 Principles, standards and procedures. The Principles, Standards and Procedures established... Orders. These Principles, Standards and Procedures are found in 18 CFR parts 710 through 717. ...

  10. 21 CFR 120.6 - Sanitation standard operating procedures.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Sanitation standard operating procedures. 120.6... Provisions § 120.6 Sanitation standard operating procedures. (a) Sanitation controls. Each processor shall have and implement a sanitation standard operating procedure (SSOP) that addresses sanitation...

  11. Standard Procedure for Grid Interaction Analysis

    International Nuclear Information System (INIS)

    Svensson, Bertil; Lindahl, Sture; Karlsson, Daniel; Joensson, Jonas; Heyman, Fredrik

    2015-01-01

    Grid events, simultaneously affecting all safety related auxiliary systems in a nuclear power plant, are critical and must be carefully addressed in the design, upgrading and operational processes. Up to now, the connecting grid has often been treated as either fully available or totally unavailable, and too little attention has been paid to specify the grid performance criteria. This paper deals with standard procedures for grid interaction analysis, to derive tools and criteria to handle grid events challenging the safety systems of the plant. Critical external power system events are investigated and characterised, with respect to severity and rate of occurrence. These critical events are then grouped with respect to impact on the safety systems, when a disturbance propagates into the plant. It is then important to make sure that 1) the impact of the disturbance will never reach any critical system, 2) the impact of the disturbance will be eliminated before it will hurt any critical system, or 3) the critical systems will be proven to be designed in such a way that they can withstand the impact of the disturbance, and the associated control and protection systems can withstand voltage and frequency transients associated with the disturbances. A number of representative disturbance profiles, reflecting connecting grid conditions, are therefore derived, to be used for equipment testing. (authors)

  12. Modified Monte Carlo procedure for particle transport problems

    International Nuclear Information System (INIS)

    Matthes, W.

    1978-01-01

    The simulation of photon transport in the atmosphere with the Monte Carlo method forms part of the EURASEP-programme. The specifications for the problems posed for a solution were such, that the direct application of the analogue Monte Carlo method was not feasible. For this reason the standard Monte Carlo procedure was modified in the sense that additional properly weighted branchings at each collision and transport process in a photon history were introduced. This modified Monte Carlo procedure leads to a clear and logical separation of the essential parts of a problem and offers a large flexibility for variance reducing techniques. More complex problems, as foreseen in the EURASEP-programme (e.g. clouds in the atmosphere, rough ocean-surface and chlorophyl-distribution in the ocean) can be handled by recoding some subroutines. This collision- and transport-splitting procedure can of course be performed differently in different space- and energy regions. It is applied here only for a homogeneous problem

  13. Dependability of technical items: Problems of standardization

    Science.gov (United States)

    Fedotova, G. A.; Voropai, N. I.; Kovalev, G. F.

    2016-12-01

    This paper is concerned with problems blown up in the development of a new version of the Interstate Standard GOST 27.002 "Industrial product dependability. Terms and definitions". This Standard covers a wide range of technical items and is used in numerous regulations, specifications, standard and technical documentation. A currently available State Standard GOST 27.002-89 was introduced in 1990. Its development involved a participation of scientists and experts from different technical areas, its draft was debated in different audiences and constantly refined, so it was a high quality document. However, after 25 years of its application it's become necessary to develop a new version of the Standard that would reflect the current understanding of industrial dependability, accounting for the changes taking place in Russia in the production, management and development of various technical systems and facilities. The development of a new version of the Standard makes it possible to generalize on a terminological level the knowledge and experience in the area of reliability of technical items, accumulated over a quarter of the century in different industries and reliability research schools, to account for domestic and foreign experience of standardization. Working on the new version of the Standard, we have faced a number of issues and problems on harmonization with the International Standard IEC 60500-192, caused first of all by different approaches to the use of terms and differences in the mentalities of experts from different countries. The paper focuses on the problems related to the chapter "Maintenance, restoration and repair", which caused difficulties for the developers to harmonize term definitions both with experts and the International Standard, which is mainly related to differences between the Russian concept and practice of maintenance and repair and foreign ones.

  14. Non-standard and improperly posed problems

    CERN Document Server

    Straughan, Brian; Ames, William F

    1997-01-01

    Written by two international experts in the field, this book is the first unified survey of the advances made in the last 15 years on key non-standard and improperly posed problems for partial differential equations.This reference for mathematicians, scientists, and engineers provides an overview of the methodology typically used to study improperly posed problems. It focuses on structural stability--the continuous dependence of solutions on the initial conditions and the modeling equations--and on problems for which data are only prescribed on part of the boundary.The book addresses continuou

  15. Standard-E hydrogen monitoring system shop acceptance test procedure

    Energy Technology Data Exchange (ETDEWEB)

    Schneider, T.C.

    1997-10-02

    The purpose of this report is to document that the Standard-E Hydrogen Monitoring Systems (SHMS-E), fabricated by Mid-Columbia Engineering (MCE) for installation on the Waste Tank Farms in the Hanford 200 Areas, are constructed as intended by the design. The ATP performance will verify proper system fabrication.

  16. Problems of procedure for studying crack resistance

    International Nuclear Information System (INIS)

    Babak, A.V.; Uskov, E.I.

    1984-01-01

    Procedures are developed for studying crack resistance in sintered hot-worked tungsten within 20-2200 deg C. Certain structural properties of the installation for studying high-temperature crack resistance of tungsten are considered. Technological peculiarities of eccentric tensile strength of tungsten specimens and methodical peculiarities of initjation and fixation of initial cracks in specimens of different tungsten alloys are studied

  17. Standard Operating Procedure for Accelerated Corrosion Testing at ARL

    Science.gov (United States)

    2017-11-01

    ARL-TN-0855 ● NOV 2017 US Army Research Laboratory Standard Operating Procedure for Accelerated Corrosion Testing at ARL by... Corrosion Testing at ARL by Thomas A Considine Weapons and Materials Research Directorate, ARL Approved for public...November 2017 2. REPORT TYPE Technical Note 3. DATES COVERED (From - To) 4. TITLE AND SUBTITLE Standard Operating Procedure for Accelerated

  18. Standard problems for structural computer codes

    International Nuclear Information System (INIS)

    Philippacopoulos, A.J.; Miller, C.A.; Costantino, C.J.

    1985-01-01

    BNL is investigating the ranges of validity of the analytical methods used to predict the behavior of nuclear safety related structures under accidental and extreme environmental loadings. During FY 85, the investigations were concentrated on special problems that can significantly influence the outcome of the soil structure interaction evaluation process. Specially, limitations and applicability of the standard interaction methods when dealing with lift-off, layering and water table effects, were investigated. This paper describes the work and the results obtained during FY 85 from the studies on lift-off, layering and water-table effects in soil-structure interaction

  19. ISP-27 OECD/NEA/CSNI International Standard Problem n.27. Bethsy experiment 9.1 B. 2. cold leg break without HPSI and with delayed ultimate procedure. Comparison report. Volume 1 + 2

    International Nuclear Information System (INIS)

    1992-11-01

    This report is the final comparison report for ISP-27, a blind problem which is based on the BETHSY test 9.1b performed in december 1989 at the Nuclear Research Center in Grenoble (France). The BETHSY integral test facility is a scaled down model of a 3 loop 900 e MW FRAMATOME PWR; the overall scaling factor applied to every volume, mass flowrate and power level is close to 1/100, while elevations are 1/1 in order to preserve the gravitational heads. The cold leg break is combined with the High Pressure Injection System (HPIS) failure. In that case, the state oriented approach requires operators to start an Ultimate Procedure, which consists in fully opening the Steam Generator (SG) atmospheric dumps as soon as they are informed of the unavailability of the HPIS. The presently studied scenario assumes a delayed application of this procedure, which is started only when the core outlet temperature rises significantly higher than the saturation temperature. The BETHSY Test 9.1b addresses, besides typical problems relevant to Small Break Loss Of Coolant Accidents (SBLOCA) such as critical 2-phase flow, loop seal clearing, heat-transfer during boil-off or accumulator injection, specific aspects related to the fast depressurization (primary to secondary and structural heat transfer), uncovered core behavior when intense condensation takes place in the SG, and primary side refilling by the Low Pressure Injection System (LPIS)

  20. Using a standards committee to design practical procedure system improvements

    International Nuclear Information System (INIS)

    Grider, D.A.; Plung, D.

    1993-01-01

    In the post-Three Mile Island (TMI) environment, numerous reports have been issued on how to improve the quality of procedures used at government and commercial nuclear facilities. The studies tend to be long on what is wrong with existing procedures and short on practical directions on how to fix those faults. Few of these studies have been conducted by practitioners with full-time procedure-managing or procedure writing experience. None of these studies go into detail on how to improve the procedure system itself. Over the last 10 yr, various nuclear facilities within the US Department of Energy (DOE) have carried out individual programs to develop procedures that meet post-TMI standards. However, ∼2 yr ago, DOE formed a Procedures Standards Committee to advise DOE in developing a set of post-TMI guidelines that could be consistently applied throughout all DOE nuclear facilities. The committee has achieved not only its original mission by producing a series of integrated guidance documents but has also evolved a systems approach to procedures management that sets new standards for procedure quality and efficiency. As members of this committee, the authors want to describe what has made the group's approach so successful. The lessons learned may be translatable to a wide range of government and commercial industry procedure programs

  1. Simple standard problem for the Preisach moving model

    International Nuclear Information System (INIS)

    Morentin, F.J.; Alejos, O.; Francisco, C. de; Munoz, J.M.; Hernandez-Gomez, P.; Torres, C.

    2004-01-01

    The present work proposes a simple magnetic system as a candidate for a Standard Problem for Preisach-based models. The system consists in a regular square array of magnetic particles totally oriented along the direction of application of an external magnetic field. The behavior of such system was numerically simulated for different values of the interaction between particles and of the standard deviation of the critical fields of the particles. The characteristic parameters of the Preisach moving model were worked out during simulations, i.e., the mean value and the standard deviation of the interaction field. For this system, results reveal that the mean interaction field depends linearly on the system magnetization, as the Preisach moving model predicts. Nevertheless, the standard deviation cannot be considered as independent of the magnetization. In fact, the standard deviation shows a maximum at demagnetization and two minima at magnetization saturation. Furthermore, not all the demagnetization states are equivalent. The plot standard deviation vs. magnetization is a multi-valuated curve when the system undergoes an AC demagnetization procedure. In this way, the standard deviation increases as the system goes from coercivity to the AC demagnetized state

  2. A Semantic Scene Description Language for Procedural Layout Solving Problems

    NARCIS (Netherlands)

    Tutenel, T.; Smelik, R.M.; Bidarra, R.; Kraker, K.J. de

    2010-01-01

    Procedural content generation is becoming more and more relevant to solve the problem of content creation for the ever growing virtual worlds of games, simulations and other applications. However, these procedures are often unintuitive or use vague parameters, making it somewhat difficult for a

  3. Standard Ship Test and Inspection Plan, Procedures and Database

    National Research Council Canada - National Science Library

    1999-01-01

    ... construction schedules and increased cost is the area of test and inspection. This project investigates existing rules and regulations for testing and inspection of commercial ships and identifies differences and similarities within the requirements. The results include comparison matrices, a standard test plan, a set of standard test procedures, and a sample test database developed for a typical commercial ship.

  4. 40 CFR 160.81 - Standard operating procedures.

    Science.gov (United States)

    2010-07-01

    .... (10) Data handling, storage and retrieval. (11) Maintenance and calibration of equipment. (12... GOOD LABORATORY PRACTICE STANDARDS Testing Facilities Operation § 160.81 Standard operating procedures... test, control, and reference substances. (4) Test system observations. (5) Laboratory or other tests...

  5. CSNI International standard problems (ISP): brief descriptions (1975-1997)

    International Nuclear Information System (INIS)

    1997-07-01

    Over the last twenty years (1975-1999) the NEA Committee on the Safety of Nuclear Installations (CSNI) has sponsored more than forty International Standard Problems (ISPs) in the fields of in-vessel thermal-hydraulic behaviour, fuel behaviour under accident conditions, fission product release and transport, core/concrete interactions, hydrogen distribution and mixing, containment thermal-hydraulic, and iodine behaviour in the containment. ISPs are comparative exercises in which predictions of different computer codes for a given physical problem are compared with each other or with the results of a carefully controlled experimental study. The main goal of ISP exercises is to increase confidence in the validity and accuracy of analytical tools or testing procedures which are needed in warranting the safety of nuclear installations, and to demonstrate the competence of involved institutions. ISP exercises are performed as 'open' or 'blind' problems. The main characteristics of 41 ISPs completed between 1975 and 1999, and 3 containment analysis standard problems (CASPs) are briefly presented

  6. The European Stroke Organisation Guidelines: a standard operating procedure

    DEFF Research Database (Denmark)

    Ntaios, George; Bornstein, Natan M; Caso, Valeria

    2015-01-01

    pace with this progress and driven by the strong determination of the European Stroke Organisation to further promote stroke management, education, and research, the European Stroke Organisation decided to delineate a detailed standard operating procedure for its guidelines. There are two important...... cornerstones in this standard operating procedure: The first is the implementation of the Grading of Recommendations Assessment, Development, and Evaluation methodology for the development of its Guideline Documents. The second one is the decision of the European Stroke Organisation to move from the classical...... and significant input from European Stroke Organisation members as well as methodologists and analysts, this document presents the official standard operating procedure for the development of the Guideline Documents of the European Stroke Organisation....

  7. A Linear Programming Reformulation of the Standard Quadratic Optimization Problem

    NARCIS (Netherlands)

    de Klerk, E.; Pasechnik, D.V.

    2005-01-01

    The problem of minimizing a quadratic form over the standard simplex is known as the standard quadratic optimization problem (SQO).It is NPhard, and contains the maximum stable set problem in graphs as a special case.In this note we show that the SQO problem may be reformulated as an (exponentially

  8. CSNI International standard problems (ISP). Brief descriptions (1975-1999)

    International Nuclear Information System (INIS)

    2000-03-01

    Over the last twenty-five years the NEA Committee on the Safety of Nuclear Installations (CSNI) has sponsored a considerable number of international activities to promote the exchange of experience between its Member countries in the use of nuclear safety codes and testing materials. A primary goal of these activities is to increase confidence in the validity and accuracy of analytical tools or testing procedures which are needed in warranting the safety of nuclear installations, and to demonstrate the competence of involved institutions. International Standard Problems (ISPs) exercises are comparative exercises in which predictions or recalculations of a given physical problem with different best-estimate computer code are compared with each other and above all with the results of a carefully specified experimental study. ISP exercises are performed as 'open' or 'blind' problems. In an open Standard Problem exercise the results of the experiment are available to the participants before performing the calculations, while in a blind Standard Problem exercise the experimental results are locked until the calculation results are made available for comparison. The CSNI-promoted ISP activity started in the early 70's and is still underway. Parallel to other national and international programs the CSNI has sponsored over more than 25 years forty-seven International Standard Problem exercises. This program has been focused mainly on the applicability of large thermal-hydraulic code systems simulating the behaviour of nuclear coolant and containment systems, fuel behaviour under accident conditions, hydrogen distribution, core-concrete interactions and fission product release and transport. One ISP exercise was organised in connection with a seismic ultimate dynamic response test. ISP exercises have proven to be very valuable to participating countries. They have been fruitful to identify code application problems and to amplify the contacts between the experimental and

  9. Standard Review Plan Maintenance Program implementing procedures document

    International Nuclear Information System (INIS)

    1996-11-01

    The implementing Procedures Document (IPD) was developed by the Inspection Program Projects Branch, Office of Nuclear Reactor Regulation, with assistance from Pacific Northwest National Laboratory, for the Standard Review Plan Maintenance Program (SRP-MP). The SRP-MP was established to maintain the Standard Review Plan (SRP) on an on-going basis. The IPD provides guidance, including an overall approach and procedures, for SRP-MP tasks. The objective of the IPD is to ensure that modifications to SRP need to reflect current NRC requirements and guidance are identified and that a consistent methodology is used to develop and revise SRP sections

  10. Standard Review Plan Update and Development Program. Implementing Procedures Document

    Energy Technology Data Exchange (ETDEWEB)

    1992-05-01

    This implementing procedures document (IPD) was prepared for use in implementing tasks under the standard review plan update and development program (SRP-UDP). The IPD provides comprehensive guidance and detailed procedures for SRP-UDP tasks. The IPD is mandatory for contractors performing work for the SRP-UDP. It is guidance for the staff. At the completion of the SRP-UDP, the IPD will be revised (to remove the UDP aspects) and will replace NRR Office Letter No. 800 as long-term maintenance procedures.

  11. Standardized methods for photography in procedural dermatology using simple equipment.

    Science.gov (United States)

    Hexsel, Doris; Hexsel, Camile L; Dal'Forno, Taciana; Schilling de Souza, Juliana; Silva, Aline F; Siega, Carolina

    2017-04-01

    Photography is an important tool in dermatology. Reproducing the settings of before photos after interventions allows more accurate evaluation of treatment outcomes. In this article, we describe standardized methods and tips to obtain photographs, both for clinical practice and research procedural dermatology, using common equipment. Standards for the studio, cameras, photographer, patients, and framing are presented in this article. © 2017 The International Society of Dermatology.

  12. Solution Tree Problem Solving Procedure for Engineering Analysis ...

    African Journals Online (AJOL)

    Illustrations are provided in the thermofluid engineering area to showcase the procedure's applications. This approach has proved to be a veritable tool for enhancing the problem-solving and computer algorithmic skills of engineering students, eliciting their curiosity, active participation and appreciation of the taught course.

  13. Procedural justice and prisoners’ mental health problems: A longitudinal study

    NARCIS (Netherlands)

    Beijersbergen, K.A.; Dirkzwager, A.J.E.; Eichelsheim, V.I.; van der Laan, P.H.; Nieuwbeerta, P.

    2013-01-01

    Background Given the high prevalence of mental health problems among prisoners, knowledge on its determinants is important. Prior cross-sectional studies suggest that procedurally just treatment within prison is a significant predictor; however, longitudinal research is lacking. Aim The aims of this

  14. Contribution from twenty two years of CSNI International Standard Problems

    International Nuclear Information System (INIS)

    1998-03-01

    This report provides a brief overview on the contribution of some CSNI International Standard Problems (ISPs) to nuclear reactor safety issues (41 ISPs performed over the last 22 years). This CSNI activity on ISPs has been one of the major activities of the Principal Working Group no.2 on Coolant System Behaviour. Its domain extended from thermal-hydraulics to several other accident domains following the main concerns of nuclear reactor safety, e.g., LOCA predictions fuel behaviour, operator procedures, containment thermal-hydraulics severe accidents, VVERs, etc. ISPs are providing unique material and benefits for some safety related issues. Clearly, all the technical findings and benefits provided by ISPs are still needed and contribute to advancement of nuclear safety. The report provides some overview on the general objectives of ISPs, content and types of ISPs, and technical domains covered by ISPs, followed by a synthesis of technical findings and benefits to the scientific community

  15. Current issues on a standard for surrogate pregnancy procedures

    OpenAIRE

    Ha, Jung-Ok

    2012-01-01

    While Korea does not have any legal statement on surrogacy, treatments are carried out in practice. As a result, every Institutional Review Board (IRB) of each fertility clinic faces an ethical predicament in reviewing each case. There is a need to arrange the institutions' own standards of surrogate pregnancy procedures before the establishment of national or professional regulation. This article examines the legal, social, and medical issues of surrogacy to help IRBs to judge their cases.

  16. Current issues on a standard for surrogate pregnancy procedures.

    Science.gov (United States)

    Ha, Jung-Ok

    2012-12-01

    While Korea does not have any legal statement on surrogacy, treatments are carried out in practice. As a result, every Institutional Review Board (IRB) of each fertility clinic faces an ethical predicament in reviewing each case. There is a need to arrange the institutions' own standards of surrogate pregnancy procedures before the establishment of national or professional regulation. This article examines the legal, social, and medical issues of surrogacy to help IRBs to judge their cases.

  17. A Schwarz alternating procedure for singular perturbation problems

    Energy Technology Data Exchange (ETDEWEB)

    Garbey, M. [Universit Claude Bernard Lyon, Villeurbanne (France); Kaper, H.G. [Argonne National Lab., IL (United States)

    1994-12-31

    The authors show that the Schwarz alternating procedure offers a good algorithm for the numerical solution of singular perturbation problems, provided the domain decomposition is properly designed to resolve the boundary and transition layers. They give sharp estimates for the optimal position of the domain boundaries and present convergence rates of the algorithm for various second-order singular perturbation problems. The splitting of the operator is domain-dependent, and the iterative solution of each subproblem is based on a modified asymptotic expansion of the operator. They show that this asymptotic-induced method leads to a family of efficient massively parallel algorithms and report on implementation results for a turning-point problem and a combustion problem.

  18. 75 FR 72942 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

    Science.gov (United States)

    2010-11-29

    ...: Harry J. Hodges, Flight Procedure Standards Branch (AFS-420), Flight Technologies and Programs Divisions..., SD, Rapid City Rgnl, ILS OR LOC RWY 32, Amdt 19 Newport News, VA, Newport News/Williamsburg Intl, ILS OR LOC RWY 7, Amdt 33 Newport News, VA, Newport News/Williamsburg Intl, ILS OR LOC RWY 25, Amdt 1...

  19. Standardization of SMP procedure and its impact on outcome

    Directory of Open Access Journals (Sweden)

    Rachita S Dhurat

    2017-01-01

    Full Text Available Background: Cosmetic deformities can result from various types of alopecia or even post hair transplantation procedures. Patients with such deformities seek aesthetically appealing longer-lasting options. Scalp concealers are commonly used by men and women to camouflage these deformities. Scalp micropigmentation (SMP is one of the concealers recently gaining popularity. Objectives: SMP is a novel technique wherein microdot tattoos are placed in a stippling pattern to mimic hair follicles that are cut close to the scalp and various variables affecting its outcome were evaluated. Methods: Forty-five subjects were recruited for the study. The various factors affecting outcome of SMP—angle of needle against the scalp, depth of needle into the scalp, time of the needle contact in scalp, speed of the rotor, resistance of scalp, color of pigment, viscosity of dye, needle number, needle thickness, and pattern of dot placement—were systematically studied in 15 patients through clinical photographs and trichoscopy. Ideal depth of pigment deposition was assessed through histopathological examination. After using these optimum variables, standardized SMP was performed in 30 patients with hair loss (3 patients with cicatricial and 27 patients with diffuse non-cicatricial alopecia. SMP was also used to create an aesthetically denser hairline. The outcome of the procedure was evaluated using standardized global photographs. Results: The ideal parameters were established to achieve standard reproducible results. There were great patient satisfaction and acceptance of the procedure. All the patients showed moderate to great improvement after the procedure with satisfactory scalp coverage. Adverse events were transient which were seen in the form of edema and redness. Conclusion: SMP offers a non-medical, tattoo-based cosmetically appealing and effective “cover-up” that hides the unsightly conditions. The cosmetic tattoo placement creates an illusion of

  20. Standard working procedures in production of traditionally fermented Sremska sausage

    Directory of Open Access Journals (Sweden)

    Vesković-Moračanin Slavica

    2011-01-01

    Full Text Available Investigations conducted within project "Techonological and protective characteristics of autochthonous strains of lactic acid bacteria isolated from traditional fermented sausages and possibilities for their implementation in the meat industry" (Project Number: 20127, financed on behalf of the Ministry for Science and Technology of the Republic of Serbia, have provided an answer on the characteristics of the quality of the used raw materials for the production of Sremska sausage - one of the most well-known Serbian traditionally fermented sausages (choice of meat, fatty tissue, additives and spices, and data have been registered in connection with the procedures of their processing, microclimatic conditions have been established (temperature, relative humidity, and air circulation during the entire process of production and fermentation, as well as the presence and types of microorganisms, primarily lactic acid bacteria (BMK, the carrier of lactic fermentation. The most important characteristics of the filling have been established, the smoking regimen, the regimens of fermentation, maturing, drying, as well as the parameters for quality and safety of the finished product. At the same time, the standard working procedure has been determined for the preparation of the meat, fatty tissue, the forming and inserting of the filling into the wrappers, as well as the characteristics of the finished products. The given standard working procedure should serve as a guideline for the meat industry in the production process of this traditional fermented sausage.

  1. Environmental Sciences Division Toxicology Laboratory standard operating procedures

    International Nuclear Information System (INIS)

    Kszos, L.A.; Stewart, A.J.; Wicker, L.F.; Logsdon, G.M.

    1989-09-01

    This document was developed to provide the personnel working in the Environmental Sciences Division's Toxicology Laboratory with documented methods for conducting toxicity tests. The document consists of two parts. The first part includes the standard operating procedures (SOPs) that are used by the laboratory in conducting toxicity tests. The second part includes reference procedures from the US Environmental Protection Agency document entitled Short-Term Methods for Estimating the Chronic Toxicity of Effluents and Receiving Waters to Freshwater Organisms, upon which the Toxicology Laboratory's SOPs are based. Five of the SOPs include procedures for preparing Ceriodaphnia survival and reproduction test. These SOPs include procedures for preparing Ceriodaphnia food (SOP-3), maintaining Ceriodaphnia cultures (SOP-4), conducting the toxicity test (SOP-13), analyzing the test data (SOP-13), and conducting a Ceriodaphnia reference test (SOP-15). Five additional SOPs relate specifically to the fathead minnow (Pimephales promelas) larval survival and growth test: methods for preparing fathead minnow larvae food (SOP-5), maintaining fathead minnow cultures (SOP-6), conducting the toxicity test (SOP-9), analyzing the test data (SOP-12), and conducting a fathead minnow reference test (DOP-14). The six remaining SOPs describe methods that are used with either or both tests: preparation of control/dilution water (SOP-1), washing of glassware (SOP-2), collection and handling of samples (SOP-7), preparation of samples (SOP-8), performance of chemical analyses (SOP-11), and data logging and care of technical notebooks (SOP-16)

  2. Standardized Procedure Content And Data Structure Based On Human Factors Requirements For Computer-Based Procedures

    International Nuclear Information System (INIS)

    Bly, Aaron; Oxstrand, Johanna; Le Blanc, Katya L

    2015-01-01

    Most activities that involve human interaction with systems in a nuclear power plant are guided by procedures. Traditionally, the use of procedures has been a paper-based process that supports safe operation of the nuclear power industry. However, the nuclear industry is constantly trying to find ways to decrease the human error rate, especially the human errors associated with procedure use. Advances in digital technology make computer-based procedures (CBPs) a valid option that provides further enhancement of safety by improving human performance related to procedure use. The transition from paper-based procedures (PBPs) to CBPs creates a need for a computer-based procedure system (CBPS). A CBPS needs to have the ability to perform logical operations in order to adjust to the inputs received from either users or real time data from plant status databases. Without the ability for logical operations the procedure is just an electronic copy of the paper-based procedure. In order to provide the CBPS with the information it needs to display the procedure steps to the user, special care is needed in the format used to deliver all data and instructions to create the steps. The procedure should be broken down into basic elements and formatted in a standard method for the CBPS. One way to build the underlying data architecture is to use an Extensible Markup Language (XML) schema, which utilizes basic elements to build each step in the smart procedure. The attributes of each step will determine the type of functionality that the system will generate for that step. The CBPS will provide the context for the step to deliver referential information, request a decision, or accept input from the user. The XML schema needs to provide all data necessary for the system to accurately perform each step without the need for the procedure writer to reprogram the CBPS. The research team at the Idaho National Laboratory has developed a prototype CBPS for field workers as well as the

  3. Standardized Procedure Content And Data Structure Based On Human Factors Requirements For Computer-Based Procedures

    Energy Technology Data Exchange (ETDEWEB)

    Bly, Aaron; Oxstrand, Johanna; Le Blanc, Katya L

    2015-02-01

    Most activities that involve human interaction with systems in a nuclear power plant are guided by procedures. Traditionally, the use of procedures has been a paper-based process that supports safe operation of the nuclear power industry. However, the nuclear industry is constantly trying to find ways to decrease the human error rate, especially the human errors associated with procedure use. Advances in digital technology make computer-based procedures (CBPs) a valid option that provides further enhancement of safety by improving human performance related to procedure use. The transition from paper-based procedures (PBPs) to CBPs creates a need for a computer-based procedure system (CBPS). A CBPS needs to have the ability to perform logical operations in order to adjust to the inputs received from either users or real time data from plant status databases. Without the ability for logical operations the procedure is just an electronic copy of the paper-based procedure. In order to provide the CBPS with the information it needs to display the procedure steps to the user, special care is needed in the format used to deliver all data and instructions to create the steps. The procedure should be broken down into basic elements and formatted in a standard method for the CBPS. One way to build the underlying data architecture is to use an Extensible Markup Language (XML) schema, which utilizes basic elements to build each step in the smart procedure. The attributes of each step will determine the type of functionality that the system will generate for that step. The CBPS will provide the context for the step to deliver referential information, request a decision, or accept input from the user. The XML schema needs to provide all data necessary for the system to accurately perform each step without the need for the procedure writer to reprogram the CBPS. The research team at the Idaho National Laboratory has developed a prototype CBPS for field workers as well as the

  4. The European Stroke Organisation Guidelines: a standard operating procedure.

    Science.gov (United States)

    Ntaios, George; Bornstein, Natan M; Caso, Valeria; Christensen, Hanne; De Keyser, Jacques; Diener, Hans-Christoph; Diez-Tejedor, Exuperio; Ferro, Jose M; Ford, Gary A; Grau, Armin; Keller, Emanuella; Leys, Didier; Russell, David; Toni, Danilo; Turc, Guillaume; Van der Worp, Bart; Wahlgren, Nils; Steiner, Thorsten

    2015-10-01

    In 2008, the recently founded European Stroke Organisation published its guidelines for the management of ischemic stroke and transient ischemic attack. This highly cited document was translated in several languages and was updated in 2009. Since then, the European Stroke Organisation has published guidelines for the management of intracranial aneurysms and subarachnoidal hemorrhage, for the establishment of stroke units and stroke centers, and recently for the management of intracerebral hemorrhage. In recent years, the methodology for the development of guidelines has evolved significantly. To keep pace with this progress and driven by the strong determination of the European Stroke Organisation to further promote stroke management, education, and research, the European Stroke Organisation decided to delineate a detailed standard operating procedure for its guidelines. There are two important cornerstones in this standard operating procedure: The first is the implementation of the Grading of Recommendations Assessment, Development, and Evaluation methodology for the development of its Guideline Documents. The second one is the decision of the European Stroke Organisation to move from the classical model of a single Guideline Document about a major topic (e.g. management of ischemic stroke) to focused modules (i.e. subdivisions of a major topic). This will enable the European Stroke Organisation to react faster when new developments in a specific stroke field occur and update its recommendations on the related module rather swiftly; with the previous approach of a single large Guideline Document, its entire revision had to be completed before an updated publication, delaying the production of up-to-date guidelines. After discussion within the European Stroke Organisation Guidelines Committee and significant input from European Stroke Organisation members as well as methodologists and analysts, this document presents the official standard operating procedure for

  5. Standards for radiation protection instrumentation: design of safety standards and testing procedures

    International Nuclear Information System (INIS)

    Meissner, Frank

    2008-01-01

    This paper describes by means of examples the role of safety standards for radiation protection and the testing and qualification procedures. The development and qualification of radiation protection instrumentation is a significant part of the work of TUV NORD SysTec, an independent expert organisation in Germany. The German Nuclear Safety Standards Commission (KTA) establishes regulations in the field of nuclear safety. The examples presented may be of importance for governments and nuclear safety authorities, for nuclear operators and for manufacturers worldwide. They demonstrate the advantage of standards in the design of radiation protection instrumentation for new power plants, in the upgrade of existing instrumentation to nuclear safety standards or in the application of safety standards to newly developed equipment. Furthermore, they show how authorities may proceed when safety standards for radiation protection instrumentation are not yet established or require actualization. (author)

  6. "Heidelberg standard examination" and "Heidelberg standard procedures" - Development of faculty-wide standards for physical examination techniques and clinical procedures in undergraduate medical education.

    Science.gov (United States)

    Nikendei, C; Ganschow, P; Groener, J B; Huwendiek, S; Köchel, A; Köhl-Hackert, N; Pjontek, R; Rodrian, J; Scheibe, F; Stadler, A-K; Steiner, T; Stiepak, J; Tabatabai, J; Utz, A; Kadmon, M

    2016-01-01

    The competent physical examination of patients and the safe and professional implementation of clinical procedures constitute essential components of medical practice in nearly all areas of medicine. The central objective of the projects "Heidelberg standard examination" and "Heidelberg standard procedures", which were initiated by students, was to establish uniform interdisciplinary standards for physical examination and clinical procedures, and to distribute them in coordination with all clinical disciplines at the Heidelberg University Hospital. The presented project report illuminates the background of the initiative and its methodological implementation. Moreover, it describes the multimedia documentation in the form of pocketbooks and a multimedia internet-based platform, as well as the integration into the curriculum. The project presentation aims to provide orientation and action guidelines to facilitate similar processes in other faculties.

  7. Piping benchmark problems for the Westinghouse AP600 Standardized Plant

    International Nuclear Information System (INIS)

    Bezler, P.; DeGrassi, G.; Braverman, J.; Wang, Y.K.

    1997-01-01

    To satisfy the need for verification of the computer programs and modeling techniques that will be used to perform the final piping analyses for the Westinghouse AP600 Standardized Plant, three benchmark problems were developed. The problems are representative piping systems subjected to representative dynamic loads with solutions developed using the methods being proposed for analysis for the AP600 standard design. It will be required that the combined license licensees demonstrate that their solutions to these problems are in agreement with the benchmark problem set

  8. The importance of production standard operating procedure in a family business company

    Science.gov (United States)

    Hongdiyanto, C.

    2017-12-01

    Plastic industry is a growing sector, therefore UD X which engage in this business has a great potential to grow as well. The problem faced by this family business company is that no standard operating procedure is used and it lead to problem in the quality and quantity produced. This research is aim to create a production standard operating procedure for UD X. Semistructure interview is used to gather information from respondent to help writer create the SOP. There are four SOP’s created, namely: classifying SOP, sorting SOP, milling SOP and packing SOP. Having SOP will improve the effectiveness of production because employees already know how to work in each stages of production process.

  9. Problem Solving in Physics: Undergraduates' Framing, Procedures, and Decision Making

    Science.gov (United States)

    Modir, Bahar

    In this dissertation I will start with the broad research question of what does problem solving in upper division physics look like? My focus in this study is on students' problem solving in physics theory courses. Some mathematical formalisms are common across all physics core courses such as using the process of separation of variables, doing Taylor series, or using the orthogonality properties of mathematical functions to set terms equal to zero. However, there are slight differences in their use of these mathematical formalisms across different courses, possibly because of how students map different physical systems to these processes. Thus, my first main research question aims to answer how students perform these recurring processes across upper division physics courses. I break this broad question into three particular research questions: What knowledge pieces do students use to make connections between physics and procedural math? How do students use their knowledge pieces coherently to provide reasoning strategies in estimation problems? How do students look ahead into the problem to read the information out of the physical scenario to align their use of math in physics? Building on the previous body of the literature, I will use the theory family of Knowledge in Pieces and provide evidence to expand this theoretical foundation. I will compare my study with previous studies and provide suggestions on how to generalize these theory expansions for future use. My experimental data mostly come from video-based classroom data. Students in groups of 2-4 students solve in-class problems in quantum mechanics and electromagnetic fields 1 courses collaboratively. In addition, I will analyze clinical interviews to demonstrate how a single case study student plays an epistemic game to estimate the total energy in a hurricane. My second research question is more focused on a particular instructional context. How do students frame problem solving in quantum mechanics? I

  10. Standard Operating Procedures for Female Genital Sexual Pain

    DEFF Research Database (Denmark)

    Fugl-Meyer, Kerstin S; Bohm-Starke, Nina; Damsted Petersen, Christina

    2012-01-01

    Introduction.  Female genital sexual pain (GSP) is a common, distressing complaint in women of all ages that is underrecognized and undertreated. Definitions and terminology for female GSP are currently being debated. While some authors have suggested that GSP is not per se a sexual dysfunction......, but rather a localized genial pain syndrome, others adhere to using clearly sexually related terms such as dyspareunia and vaginismus. Aim.  The aims of this brief review are to present definitions of the different types of female GSP. Their etiology, incidence, prevalence, and comorbidity with somatic......-Meyer KS, Bohm-Starke N, Damsted Petersen C, Fugl-Meyer A, Parish S, and Giraldi A. Standard operating procedures for female genital sexual pain. J Sex Med **;**:**-**....

  11. Quality assurance: Importance of systems and standard operating procedures.

    Science.gov (United States)

    Manghani, Kishu

    2011-01-01

    It is mandatory for sponsors of clinical trials and contract research organizations alike to establish, manage and monitor their quality control and quality assurance systems and their integral standard operating procedures and other quality documents to provide high-quality products and services to fully satisfy customer needs and expectations. Quality control and quality assurance systems together constitute the key quality systems. Quality control and quality assurance are parts of quality management. Quality control is focused on fulfilling quality requirements, whereas quality assurance is focused on providing confidence that quality requirements are fulfilled. The quality systems must be commensurate with the Company business objectives and business model. Top management commitment and its active involvement are critical in order to ensure at all times the adequacy, suitability, effectiveness and efficiency of the quality systems. Effective and efficient quality systems can promote timely registration of drugs by eliminating waste and the need for rework with overall financial and social benefits to the Company.

  12. Standard procedures for pooling health physics data for epidemiologic studies

    International Nuclear Information System (INIS)

    Strom, D.J.; Beck, W.L.; Stansbury, P.S.; Tankersley, W.G.; Watson, J.E. Jr.

    1983-01-01

    The objectives of the study are: (1) to determine the availability of dosimetry data and supporting documentation at multiple facilities; (2) to develop criteria and methods for optimally retrieving data; (3) to evaluate and document the quality and completeness of data and dosimetry programs; (4) to put dosimetry data (e.g., external, whole body counting, and bioassay data) from various facilities in a single format for epidemiologic analysis; and (5) to document all work for peer review. To achieve these objectives, a ''Dosimetry Records and Radiation Hazards Questionnaire'' was developed to send to the facilities under study. Responses to this questionnaire are used to develop data retrieval criteria and methods, and to retrieve data. Dose data are reformatted into Standard Intermediate Dosimetry Files for editing and characterization. Evaluations of dosimetry programs are performed concurrently. Results of these steps are brought together and analysis files created. Status of this work in the context of the Department of Energy 5-Rem Study is reported. The standard procedures are applicable to single- as well as multiple-facility studies

  13. A standardized procedure for using human corpus cavernosum strips to evaluate drug activity.

    Science.gov (United States)

    Mirone, V; Sorrentino, R; di Villa Bianca, R; Imbimbo, C; Palmieri, A; Fusco, F; Tajana, G; Cirino, G

    2000-01-01

    The main problem of using human corpus cavernosum (HCC) tissue to perform bioassay is linked to its limited availability further complicated by the heterogeneous source of the tissues used. Here, we show that gender reassignment is a reliable source of human tissue without major ethical problems. Indeed, the entire corpus cavernosum is obtained from the surgery procedure, which allows creating a standardized procedure to prepare HCC strip. In addition, human tissue, if kept in the fridge in the condition described, does not loose its ability to contract to phenylephrine (PE; alpha agonist), angiotensin II (AG II) and KCl up to 4 days. Furthermore, once contracted with PE, HCC relaxes to acetylcholine (endothelium-dependent mechanism); sodium nitroprusside (endothelium-independent mechanism); cromakalim (CRK), a K(ATP) channel opener; or alprostadil, a synthetic PGE2 (ALPR). In conclusion, we have standardized a procedure that allows the use of HCC strips to evaluate drug activity and/or to study pathophysiological mechanisms with an intact functional human tissue up to 4 days from the surgery procedure.

  14. CSNI International Standard Problems (ISP). Brief descriptions (1975-1994)

    International Nuclear Information System (INIS)

    1994-07-01

    Between 1975 and 1994 the NEA Committee on the Safety of Nuclear Installations (CSNI) has sponsored some forty International Standard Problems (ISPs) in the fields of in-vessel thermal-hydraulic behaviour, fuel behaviour under accident conditions, fission product release and transport, core/concrete interactions, hydrogen distribution and mixing, containment thermal-hydraulics. ISPs are comparative exercises in which predictions of different computer codes for a given physical problem are compared with each other or with the results of a carefully controlled experimental study. The main goal of ISP exercises is to increase confidence in the validity and accuracy of tools which are used in assessing the safety of nuclear installations. Moreover, they enable code users to gain experience and demonstrate their competence. ISPs are performed as 'open' or 'blind' problems. In an open Standard Problem the results of the experiment are available to the participants before performing the calculations, while in a blind Standard Problem the results are locked until the calculational results are made available for comparison. Experiments selected to support ISP exercises are exceptionally well documented; they provide the framework for several code validation matrices. This report briefly describes 36 ISPs and 3 containment analysis standard problems (CASP)

  15. Proposal of a micromagnetic standard problem for ferromagnetic resonance simulations

    Energy Technology Data Exchange (ETDEWEB)

    Baker, Alexander [Department of Physics, Clarendon Laboratory, University of Oxford, Oxford, 3PU, OX1 (United Kingdom); Beg, Marijan; Ashton, Gregory; Albert, Maximilian; Chernyshenko, Dmitri [Faculty of Engineering and the Environment, University of Southampton, SO17 1BJ, Southampton (United Kingdom); Wang, Weiwei [Department of Physics, Ningbo University, Ningbo, 315211 China (China); Zhang, Shilei [Department of Physics, Clarendon Laboratory, University of Oxford, Oxford, 3PU, OX1 (United Kingdom); Bisotti, Marc-Antonio; Franchin, Matteo [Faculty of Engineering and the Environment, University of Southampton, SO17 1BJ, Southampton (United Kingdom); Hu, Chun Lian; Stamps, Robert [SUPA School of Physics and Astronomy, University of Glasgow, G12, Glasgow, 8QQ United Kingdom (United Kingdom); Hesjedal, Thorsten, E-mail: t.hesjedal1@physics.ox.ac.uk [Department of Physics, Clarendon Laboratory, University of Oxford, Oxford, 3PU, OX1 (United Kingdom); Fangohr, Hans [Faculty of Engineering and the Environment, University of Southampton, SO17 1BJ, Southampton (United Kingdom)

    2017-01-01

    Nowadays, micromagnetic simulations are a common tool for studying a wide range of different magnetic phenomena, including the ferromagnetic resonance. A technique for evaluating reliability and validity of different micromagnetic simulation tools is the simulation of proposed standard problems. We propose a new standard problem by providing a detailed specification and analysis of a sufficiently simple problem. By analyzing the magnetization dynamics in a thin permalloy square sample, triggered by a well defined excitation, we obtain the ferromagnetic resonance spectrum and identify the resonance modes via Fourier transform. Simulations are performed using both finite difference and finite element numerical methods, with OOMMF and Nmag simulators, respectively. We report the effects of initial conditions and simulation parameters on the character of the observed resonance modes for this standard problem. We provide detailed instructions and code to assist in using the results for evaluation of new simulator tools, and to help with numerical calculation of ferromagnetic resonance spectra and modes in general. - Highlights: ●Micromagnetic standard problem for FerroMagnetic Resonance (FMR). ●Overview of FMR simulation techniques. ●Define reproducible test problem with ring down method. ●Example configuration files, scripts and post processing for OOMMF and NMag. ●Code and data available in Ref. [23].

  16. Standard operating procedures for ESPEN guidelines and consensus papers.

    Science.gov (United States)

    Bischoff, Stephan C; Singer, Pierre; Koller, Michael; Barazzoni, Rocco; Cederholm, Tommy; van Gossum, André

    2015-12-01

    The ESPEN Guideline standard operating procedures (SOP) is based on the methodology provided by the Association of Scientific Medical Societies of Germany (AWMF), the Scottish Intercollegiate Guidelines Network (SIGN), and the Centre for Evidence-based Medicine at the University of Oxford. The SOP is valid and obligatory for all future ESPEN-sponsored guideline projects aiming to generate high-quality guidelines on a regular basis. The SOP aims to facilitate the preparation of guideline projects, to streamline the consensus process, to ensure quality and transparency, and to facilitate the dissemination and publication of ESPEN guidelines. To achieve this goal, the ESPEN Guidelines Editorial board (GEB) has been established headed by two chairmen. The GEB will support and supervise the guideline processes and is responsible for the strategic planning of ESPEN guideline activities. Key elements of the SOP are the generation of well-built clinical questions according to the PICO system, a systemic literature search, a classification of the selected literature according to the SIGN evidence levels providing an evidence table, and a clear and straight-forward consensus procedure consisting of online voting's and a consensus conference. Only experts who meet the obligation to disclosure any potential conflict of interests and who are not employed by the Industry can participate in the guideline process. All recommendations will be graded according to the SIGN grading and novel outcome models besides biomedical endpoints. This approach will further extent the leadership of ESPEN in creating up-to-date and suitable for implementation guidelines and in sharing knowledge on malnutrition and clinical nutrition. Copyright © 2015 Elsevier Ltd and European Society for Clinical Nutrition and Metabolism. All rights reserved.

  17. Standard operating procedures in the disorders of orgasm and ejaculation.

    Science.gov (United States)

    McMahon, Chris G; Jannini, Emmanuele; Waldinger, Marcel; Rowland, David

    2013-01-01

    Ejaculatory/orgasmic disorders are common male sexual dysfunctions and include premature ejaculation (PE), inhibited ejaculation, anejaculation, retrograde ejaculation, and anorgasmia. To provide recommendations and guidelines of the current state-of-the-art knowledge for management of ejaculation/orgasmic disorders in men as standard operating procedures (SOPs) for the treating health care professional. The International Society of Sexual Medicine Standards Committee assembled over 30 multidisciplinary experts to establish SOPs for various male and female sexual medicine topics. The SOP for the management of disorders of orgasm and ejaculation represents the opinion of four experts from four countries developed in a process over a 2-year period. Expert opinion was based on grading of evidence-based medical literature, limited expert opinion, widespread internal committee discussion, public presentation, and debate. PE management is largely dependent upon etiology. Lifelong PE is best managed with PE pharmacotherapy (selective serotonin reuptake inhibitors and/or topical anesthetics). The management of acquired PE is etiology specific and may include erectile dysfunction (ED) pharmacotherapy in men with comorbid ED. All men seeking treatment for PE should receive basic psychosexual education. Graded behavioral therapy is indicated when psychogenic or relationship factors are present and is often best combined with PE pharmacotherapy in an integrated treatment program. Delayed ejaculation, anejaculation, and/or anorgasmia may have a biogenic and/or psychogenic etiology. Men with age-related penile hypoanesthesia should be educated, reassured, and instructed in revised sexual techniques which maximize arousal. Retrograde ejaculation is managed by education, patient reassurance, and pharmacotherapy. Additional research is required to further the understanding of the disorders of ejaculation and orgasm. © 2012 International Society for Sexual Medicine.

  18. Standard formatted data units-control authority procedures

    Science.gov (United States)

    1991-01-01

    The purpose of this document is to establish a set of minimum and optional requirements for the implementation of Control Authority (CA) organizations within and among the Agencies participating in the Consultative Committee for Space Data Systems (CCSDS). By satisfying these requirements, the resultant cooperating set of CA organizations will produce a global CA service supporting information transfer with digital data under the Standard Formatted Data Unit (SFDU) concept. This service is primarily accomplished through the registration, permanent archiving, and dissemination of metadata in the form of Metadata Objects (MDO) that assist in the interpretation of data objects received in SFDU form. This Recommendation addresses the responsibilities, services, and interface protocols for a hierarchy of CA organizations. The top level, consisting of the CCSDS Secretariat and its operational agent, is unique and primarily provides a global coordination function. The lower levels are Agency CA organizations that have primary responsibility for the registration, archiving, and dissemination of MDOs. As experience is gained and technology evolves, the CA Procedures will be extended to include enhanced services and their supporting protocols. In particular, it is anticipated that eventually CA organizations will be linked via networks on a global basis, and will provide requestors with online automated access to CA services. While this Recommendation does not preclude such operations, it also does not recommend the specific protocols to be used to ensure global compatibility of these services. These recommendations will be generated as experience is gained.

  19. Quality assurance: Importance of systems and standard operating procedures

    Directory of Open Access Journals (Sweden)

    Kishu Manghani

    2011-01-01

    Full Text Available It is mandatory for sponsors of clinical trials and contract research organizations alike to establish, manage and monitor their quality control and quality assurance systems and their integral standard operating procedures and other quality documents to provide high-quality products and services to fully satisfy customer needs and expectations. Quality control and quality assurance systems together constitute the key quality systems. Quality control and quality assurance are parts of quality management. Quality control is focused on fulfilling quality requirements, whereas quality assurance is focused on providing confidence that quality requirements are fulfilled. The quality systems must be commensurate with the Company business objectives and business model. Top management commitment and its active involvement are critical in order to ensure at all times the adequacy, suitability, effectiveness and efficiency of the quality systems. Effective and efficient quality systems can promote timely registration of drugs by eliminating waste and the need for rework with overall financial and social benefits to the Company.

  20. Manual of Standard Operating Procedures for Veterinary Drug Residue Analysis

    International Nuclear Information System (INIS)

    2016-01-01

    Laboratories are crucial to national veterinary drug residue monitoring programmes. However, one of the main challenges laboratories encounter is obtaining access to relevant methods of analysis. Thus, in addition to training, providing technical advice and transferring technology, the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture has resolved to develop clear and practical manuals to support Member State laboratories. The Coordinated Research Project (CRP) on Development of Radiometric and Allied Analytical Methods to Strengthen Residue Control Programs for Antibiotic and Anthelmintic Veterinary Drug Residues has developed a number of analytical methods as standard operating procedures (SOPs), which are now compiled here. This publication contains SOPs on chromatographic and spectrometric techniques, as well as radioimmunoassay and associated screening techniques, for various anthelmintic and antimicrobial veterinary drug residue analysis. Some analytical method validation protocols are also included. The publication is primarily aimed at food and environmental safety laboratories involved in testing veterinary drug residues, including under organized national residue monitoring programmes. It is expected to enhance laboratory capacity building and competence through the use of radiometric and complementary tools and techniques. The publication is also relevant for applied research on residues of veterinary drugs in food and environmental samples

  1. Estimating the Standard Error of the Judging in a modified-Angoff Standards Setting Procedure

    Directory of Open Access Journals (Sweden)

    Robert G. MacCann

    2004-03-01

    Full Text Available For a modified Angoff standards setting procedure, two methods of calculating the standard error of the..judging were compared. The Central Limit Theorem (CLT method is easy to calculate and uses readily..available data. It estimates the variance of mean cut scores as a function of the variance of cut scores within..a judging group, based on the independent judgements at Stage 1 of the process. Its theoretical drawback is..that it is unable to take account of the effects of collaboration among the judges at Stages 2 and 3. The..second method, an application of equipercentile (EQP equating, relies on the selection of very large stable..candidatures and the standardisation of the raw score distributions to remove effects associated with test..difficulty. The standard error estimates were then empirically obtained from the mean cut score variation..observed over a five year period. For practical purposes, the two methods gave reasonable agreement, with..the CLT method working well for the top band, the band that attracts most public attention. For some..bands in English and Mathematics, the CLT standard error was smaller than the EQP estimate, suggesting..the CLT method be used with caution as an approximate guide only.

  2. Measuring fuel moisture content in Alaska: standard methods and procedures.

    Science.gov (United States)

    Rodney A. Norum; Melanie. Miller

    1984-01-01

    Methods and procedures are given for collecting and processing living and dead plant materials for the purpose of determining their water content. Wild-land fuels in Alaska are emphasized, but the methodology is applicable elsewhere. Guides are given for determining the number of samples needed to attain a chosen precision. Detailed procedures are presented for...

  3. 21 CFR 606.100 - Standard operating procedures.

    Science.gov (United States)

    2010-04-01

    ... units. (9) Procedures for investigating adverse donor and recipient reactions. (10) Storage temperatures... accurately relating the product(s) to the donor. (5) Blood collection procedure, including in-process precautions taken to measure accurately the quantity of blood removed from the donor. (6) Methods of component...

  4. Reliability and Validity of 10 Different Standard Setting Procedures.

    Science.gov (United States)

    Halpin, Glennelle; Halpin, Gerald

    Research indicating that different cut-off points result from the use of different standard-setting techniques leaves decision makers with a disturbing dilemma: Which standard-setting method is best? This investigation of the reliability and validity of 10 different standard-setting approaches was designed to provide information that might help…

  5. Blood banking and regulation: procedures, problems, and alternatives

    National Research Council Canada - National Science Library

    Dauer, Edward A

    This volume examines regulatory and policymaking procedures in blood banking, regulatory enforcement and compliance, innovations and alternatives in regulation, congressional oversight and regulatory...

  6. Finite element analyses for Seismic Shear Wall International Standard Problem

    International Nuclear Information System (INIS)

    Park, Y.; Hofmayer, C.; Chokshi, N.

    1997-01-01

    In the seismic design of shear wall structures, e.g., nuclear reactor buildings, a linear FEM analysis is frequently used to quantify the stresses under the design loading condition. The final design decisions, however, are still based on empirical design rules established over decades from accumulated laboratory test data. This paper presents an overview of the state-of-the-art on the application of nonlinear FEM analysis to reinforced concrete (RC) shear wall structures under severe earthquake loadings based on the findings obtained during the Seismic Shear Wall International Standard Problem (SSWISP) Workshop in 1996. Also, BNL's analysis results of the International Standard Problem (ISP) shear walls under monotonic static, cyclic static and dynamic loading conditions are described

  7. Step by Step: Biology Undergraduates’ Problem-Solving Procedures during Multiple-Choice Assessment

    Science.gov (United States)

    Prevost, Luanna B.; Lemons, Paula P.

    2016-01-01

    This study uses the theoretical framework of domain-specific problem solving to explore the procedures students use to solve multiple-choice problems about biology concepts. We designed several multiple-choice problems and administered them on four exams. We trained students to produce written descriptions of how they solved the problem, and this allowed us to systematically investigate their problem-solving procedures. We identified a range of procedures and organized them as domain general, domain specific, or hybrid. We also identified domain-general and domain-specific errors made by students during problem solving. We found that students use domain-general and hybrid procedures more frequently when solving lower-order problems than higher-order problems, while they use domain-specific procedures more frequently when solving higher-order problems. Additionally, the more domain-specific procedures students used, the higher the likelihood that they would answer the problem correctly, up to five procedures. However, if students used just one domain-general procedure, they were as likely to answer the problem correctly as if they had used two to five domain-general procedures. Our findings provide a categorization scheme and framework for additional research on biology problem solving and suggest several important implications for researchers and instructors. PMID:27909021

  8. Standard interface files and procedures for reactor physics codes. Version IV

    International Nuclear Information System (INIS)

    O'Dell, R.D.

    1977-09-01

    Standards, procedures, and recommendations of the Committee on Computer Code Coordination for promoting the exchange of reactor physics codes are updated to Version IV status. Standards and procedures covering general programming, program structure, standard interface files, and file management and handling subroutines are included

  9. Manual for the GAW Precipitation Chemistry Programme: Guidelines, Data Quality Objectives and Standard Operating Procedures

    National Research Council Canada - National Science Library

    Allan, Mary A

    2004-01-01

    This is a manual for the Global Atmosphere Watch Precipitation Chemistry (GAW-PC) Programme. Where possible, it describes standard operating procedures and otherwise provides guidance on methods and procedures...

  10. 40 CFR 761.79 - Decontamination standards and procedures.

    Science.gov (United States)

    2010-07-01

    .... (b) Decontamination standards. Chopping (including wire chopping), distilling, filtering, oil/water... burned and marketed in accordance with the requirements for used oil in § 761.20(e), disposed of in... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Decontamination standards and...

  11. Standardization of the time for the execution of HANARO start-up and shutdown procedures

    International Nuclear Information System (INIS)

    Choi, H. Y.; Lim, I. C.; Hwang, S. R.; Kang, T. J.; Youn, D. B.

    2003-01-01

    For the standardization of the time to execute HANARO start-up and shutdown procedures, code names were assigned to the individual procedures and the work time were investigated. The data recorded by the operators during start-up and shutdown were statistically analyzed. The analysis results will be used for the standardization of start-up and shutdown procedures and it will be reflected in the procedure document

  12. The prevalence of mental health problems among users of NHS stop smoking services: effects of implementing a routine screening procedure

    Directory of Open Access Journals (Sweden)

    Ratschen Elena

    2011-08-01

    Full Text Available Abstract Background Tobacco dependence among people with mental health problems is an issue that deserves attention both from a clinical and from a public health perspective. Research suggests that Stop Smoking Services often fail to ask clients about underlying mental health problems and thus fail to put in place the treatment adaptations and liaison procedures often required to meet the needs of clients with a mental health condition who want to stop smoking. This study assesses the recording of mental health problems in a large NHS stop smoking service in England and examines the effect of implementing a short screening procedure on recording mental health conditions. Methods Treatment records from the Stop Smoking Service covering a period of 13 months were audited. The prevalence of reported mental health problems in the six month period before the implementation of the mental health screening procedure was compared with that of the six month period following implementation. The screening procedure was only implemented in the support services directly provided by the Stop Smoking Service. Comparisons were also made with third-party sections of the service where no such screening procedure was introduced. Results The prevalence of reported mental health problems among a total of n = 4999 clients rose from less than 1% before implementation of the screening procedure to nearly 12% in the period following implementation, with the change being statistically significant. No significant rise was observed over the same period in the sections of the service where no screening procedure was implemented. Conclusions The absence of standard procedures to record mental health problems among service users in many stop smoking services is currently likely to prevent the detection of co morbidity. Implementing a simple screening procedure appears suitable to increase the routine recording of mental health problems in a stop smoking service, which is an

  13. ASTEC participation in the international standard problem on KAEVER

    International Nuclear Information System (INIS)

    Spitz, P.; Van Dorsselaere, J.P.; Schwinges, B.; Schwarz, S.

    2001-01-01

    The objectives of the International Standard Problem no 44 was aerosol depletion behaviour under severe accident conditions in a LWR containment examined in the KAEVER test facility of Battelle (Germany). Nine organisations participated with 5 different codes in the ISP44, including a joint participation of GRS and IPSN with the integral code ASTEC (and in particular the CPA module) they have commonly developed. Five tests were selected from the KAEVER test matrix: K123, K148, K186 and K188 as open standard problems and the three-component test K187 as blind standard problem. All these tests were performed in supersaturated conditions and with slight fog formation, which are the most ambitious conditions for the coupled problem of thermal hydraulics and aerosol processes. The comparison between calculation and test showed a good agreement for all the tests with respect to the thermal-hydraulic conditions in the vessel, i.e. total pressure, atmosphere temperature, sump water and nitrogen mass, etc.... As for aerosol depletion, the ASTEC results were in a good overall agreement with the measured data. The code in particular predicted well the fast depletion of the hygroscopic and mixed aerosols and the slow depletion of insoluble silver aerosol. The important effects of bulk condensation, solubility and the Kelvin effect on the aerosol depletion were well predicted. However the code overestimation of steam condensation on hygroscopic aerosols in supersaturated conditions indicates that some slight improvements of the appropriate ASTEC models are needed in the future. In the final ISP44 workshop, the deviations of the ASTEC results with respect to the experiments were considered to be small compared to those of most other codes. (authors)

  14. Applications of Desensitization Procedures for School-Related Problems; A Review.

    Science.gov (United States)

    Prout, H. Thompson; Harvey, John R.

    1978-01-01

    A variety of desensitization and counterconditioning procedures have been utilized to deal with school-related problems. These procedures are reviewed with respect to applications for treating school phobia, test anxiety, and other academic anxieties. (Author)

  15. Standard Problems for CFD Validation for NGNP - Status Report

    International Nuclear Information System (INIS)

    Johnson, Richard W.; Schultz, Richard R.

    2010-01-01

    The U.S. Department of Energy (DOE) is conducting research and development to support the resurgence of nuclear power in the United States for both electrical power generation and production of process heat required for industrial processes such as the manufacture of hydrogen for use as a fuel in automobiles. The project is called the Next Generation Nuclear Plant (NGNP) Project, which is based on a Generation IV reactor concept called the very high temperature reactor (VHTR). The VHTR will be of the prismatic or pebble bed type; the former is considered herein. The VHTR will use helium as the coolant at temperatures ranging from 250 C to perhaps 1000 C. While computational fluid dynamics (CFD) has not previously been used for the safety analysis of nuclear reactors in the United States, it is being considered for existing and future reactors. It is fully recognized that CFD simulation codes will have to be validated for flow physics reasonably close to actual fluid dynamic conditions expected in normal operational and accident situations. The ''Standard Problem'' is an experimental data set that represents an important physical phenomenon or phenomena, whose selection is based on a phenomena identification and ranking table (PIRT) for the reactor in question. It will be necessary to build a database that contains a number of standard problems for use to validate CFD and systems analysis codes for the many physical problems that will need to be analyzed. The first two standard problems that have been developed for CFD validation consider flow in the lower plenum of the VHTR and bypass flow in the prismatic core. Both involve scaled models built from quartz and designed to be installed in the INL's matched index of refraction (MIR) test facility. The MIR facility employs mineral oil as the working fluid at a constant temperature. At this temperature, the index of refraction of the mineral oil is the same as that of the quartz. This provides an advantage to the

  16. Policy, Procedures and Standards for Enterprise Information Management

    Science.gov (United States)

    This policy establishes a standard approach for managing information produced by, funded by, or received per regulated reporting and/or federal-wide requirements and subsequently held or cataloged in information management systems by EPA.

  17. Standard physics solution to the solar neutrino problem?

    Energy Technology Data Exchange (ETDEWEB)

    Dar, A [Technion-Israel Inst. of Tech., Haifa (Israel). Dept. of Physics

    1996-11-01

    The {sup 8}B solar neutrino flux predicted by the standard solar model (SSM) is consistent within the theoretical and experimental uncertainties with that at Kamiokande. The Gallium and Chlorine solar neutrino experiments, however, seem to imply that the {sup 7}Be solar neutrino flux is strongly suppressed compared with that predicted by the SSM. If the {sup 7}Be solar neutrino flux is suppressed, still it can be due to astrophysical effects not included in the simplistic SSM. Such effects include short term fluctuations or periodic variation of the temperature in the solar core, rotational mixing of {sup 3}He in the solar core, and dense plasma effects which may strongly enhance p-capture by {sup 7}Be relative to e-capture. The new generation of solar observations which already look non stop deep into the sun, like Superkamiokande through neutrinos, and SOHO and GONG through acoustic waves, may point at the correct solution. Only Superkamiokande and/or future solar neutrino experiments, such as SNO, BOREXINO and HELLAZ, will be able to find out whether the solar neutrino problem is caused by neutrino properties beyond the minimal standard electroweak model or whether it is just a problem of the too simplistic standard solar model. (author) 1 fig., 3 tabs., refs.

  18. Standard problems to evaluate soil structure interaction computer codes

    International Nuclear Information System (INIS)

    Miller, C.A.; Costantino, C.J.; Philippacopoulos, A.J.

    1979-01-01

    The seismic response of nuclear power plant structures is often calculated using lumped parameter methods. A finite element model of the structure is coupled to the soil with a spring-dashpot system used to represent the interaction process. The parameters of the interaction model are based on analytic solutions to simple problems which are idealizations of the actual problems of interest. The objective of the work reported in this paper is to compare predicted responses using the standard lumped parameter models with experimental data. These comparisons are shown to be good for a fairly uniform soil system and for loadings which do not result in nonlinear interaction effects such as liftoff. 7 references, 7 figures

  19. An analysis of CSNI standard problem, No. 8

    International Nuclear Information System (INIS)

    Sasaki, Shinobu; Araya, Fumimasa

    1980-03-01

    The CSNI International Standard Problem (ISP8), based on the Semiscale S-06-3 Test, was analyzed in the course of verification work of the computer code ALARM-P1. In this report, described was the result of the initial trial, which had been submitted to the CSNI. Due to the limitations of ALARM-P1 capability, only the blowdown portion of the transient was calculated. Though the hydraulic behavior before ECCS injection agreed with the test data, the ALARM-P1 could not continue calculation after 26 seconds due to severe predicted instability following the ECCS injection. The prediction of surface temperature of the heater rods was also unsatisfactory. Several problems to be improved have been identified both in the analytical model and the input data. (author)

  20. 21 CFR 58.81 - Standard operating procedures.

    Science.gov (United States)

    2010-04-01

    ...) Data handling, storage, and retrieval. (11) Maintenance and calibration of equipment. (12) Transfer... LABORATORY PRACTICE FOR NONCLINICAL LABORATORY STUDIES Testing Facilities Operation § 58.81 Standard... forth nonclinical laboratory study methods that management is satisfied are adequate to insure the...

  1. 76 FR 54528 - Standard Operating Procedures (SOP) of the Aircraft Certification Service (AIR) Process for the...

    Science.gov (United States)

    2011-09-01

    ...) of the Aircraft Certification Service (AIR) Process for the Sequencing of Certification and... on the Aircraft Certification Service (AIR) standard operating procedure (SOP) describing the process... comments on the SOP : AIR-100-001; Standard Operating Procedure--Aircraft Certification Service Project...

  2. Procedures and Standards Handbook. Version 3.0. What Works Clearinghouse

    Science.gov (United States)

    What Works Clearinghouse, 2014

    2014-01-01

    This "What Works Clearinghouse Procedures and Standards Handbook (Version 3.0)" provides a detailed description of the standards and procedures of the What Works Clearinghouse (WWC). The remaining chapters of this Handbook are organized to take the reader through the basic steps that the WWC uses to develop a review protocol, identify…

  3. Operational procedure standard for occurrences involving radioactive materials

    International Nuclear Information System (INIS)

    Piekarz, Leonardo; Rezende, Talita C.; Pinheiro, Christiano J.G.

    2017-01-01

    This study has as objective to analyze more deeply the actions of response to emergencies involving radioactive materials, in the intent to establish a pattern to the actions performed by the military fire fighters of the Military Fire Brigade of Minas Gerais. To met these goals, it has been attempted to analyze the procedures utilized and recommended, nowadays, for the military fire fighters of CBMMG, and through directed studies, to suggest new actions possible to be executed in the local of the emergency in a way that will not expose the garrison to doses of ionizing radiation that may prejudice them. It is a study of bibliographic, exploratory, and also descriptive nature, realized through a qualitative approach. The techniques used for the research were the analysis of institutional documents, norms and other literature produced by renamed entities in the radiologic and biosafety areas. It was then concluded that CBMMG, through simple actions of response, can provide higher quality and safety in the operations involving radiologic accidents, standing out that the implemented actions nowadays are very beneath the capacity of the corporation, due to the lack of knowledge of the matter by the fire fighters. It was proposed, then, that new actions be implemented and instituted as operational procedures to be used on those emergencies, with the objective of provide a higher safety and professionalism in the attendance to emergencies involving radioactive materials. (author)

  4. Operational procedure standard for occurrences involving radioactive materials

    Energy Technology Data Exchange (ETDEWEB)

    Piekarz, Leonardo, E-mail: leonardopbm@yahoo.com.br [Academia de Bombeiros Militar de Minas Gerais, Belo Horizonte, MG (Brazil); Rezende, Talita C.; Pinheiro, Christiano J.G., E-mail: talitacolombi@yahoo.com, E-mail: christrieste@yahoo.it [Universidade Federal do Espirito Santo (CCA/UFES), Alegre, ES (Brazil). Programa de Pós-Graduação em Engenharia Química

    2017-07-01

    This study has as objective to analyze more deeply the actions of response to emergencies involving radioactive materials, in the intent to establish a pattern to the actions performed by the military fire fighters of the Military Fire Brigade of Minas Gerais. To met these goals, it has been attempted to analyze the procedures utilized and recommended, nowadays, for the military fire fighters of CBMMG, and through directed studies, to suggest new actions possible to be executed in the local of the emergency in a way that will not expose the garrison to doses of ionizing radiation that may prejudice them. It is a study of bibliographic, exploratory, and also descriptive nature, realized through a qualitative approach. The techniques used for the research were the analysis of institutional documents, norms and other literature produced by renamed entities in the radiologic and biosafety areas. It was then concluded that CBMMG, through simple actions of response, can provide higher quality and safety in the operations involving radiologic accidents, standing out that the implemented actions nowadays are very beneath the capacity of the corporation, due to the lack of knowledge of the matter by the fire fighters. It was proposed, then, that new actions be implemented and instituted as operational procedures to be used on those emergencies, with the objective of provide a higher safety and professionalism in the attendance to emergencies involving radioactive materials. (author)

  5. A Comparison of Standard-Setting Procedures for an OSCE in Undergraduate Medical Education.

    Science.gov (United States)

    Kaufman, David M.; Mann, Karen V.; Muijtjens, Arno M. M.; van der Vleuten, Cees P. M.

    2000-01-01

    Compared four standard-setting procedures for an objective structure clinical examination (OSCE) in medical education. Applied Angoff, borderline, relative, and holistic procedures to the data used to establish a cutoff score for a pass/fail decision. The Angoff and borderline procedures gave similar results; however, the relative and holistic…

  6. Using standardized patients versus video cases for representing clinical problems in problem-based learning.

    Science.gov (United States)

    Yoon, Bo Young; Choi, Ikseon; Choi, Seokjin; Kim, Tae-Hee; Roh, Hyerin; Rhee, Byoung Doo; Lee, Jong-Tae

    2016-06-01

    The quality of problem representation is critical for developing students' problem-solving abilities in problem-based learning (PBL). This study investigates preclinical students' experience with standardized patients (SPs) as a problem representation method compared to using video cases in PBL. A cohort of 99 second-year preclinical students from Inje University College of Medicine (IUCM) responded to a Likert scale questionnaire on their learning experiences after they had experienced both video cases and SPs in PBL. The questionnaire consisted of 14 items with eight subcategories: problem identification, hypothesis generation, motivation, collaborative learning, reflective thinking, authenticity, patient-doctor communication, and attitude toward patients. The results reveal that using SPs led to the preclinical students having significantly positive experiences in boosting patient-doctor communication skills; the perceived authenticity of their clinical situations; development of proper attitudes toward patients; and motivation, reflective thinking, and collaborative learning when compared to using video cases. The SPs also provided more challenges than the video cases during problem identification and hypotheses generation. SPs are more effective than video cases in delivering higher levels of authenticity in clinical problems for PBL. The interaction with SPs engages preclinical students in deeper thinking and discussion; growth of communication skills; development of proper attitudes toward patients; and motivation. Considering the higher cost of SPs compared with video cases, SPs could be used most advantageously during the preclinical period in the IUCM curriculum.

  7. The problem of epistemic jurisdiction in global governance: The case of sustainability standards for biofuels.

    Science.gov (United States)

    Winickoff, David E; Mondou, Matthieu

    2017-02-01

    While there is ample scholarly work on regulatory science within the state, or single-sited global institutions, there is less on its operation within complex modes of global governance that are decentered, overlapping, multi-sectorial and multi-leveled. Using a co-productionist framework, this study identifies 'epistemic jurisdiction' - the power to produce or warrant technical knowledge for a given political community, topical arena or geographical territory - as a central problem for regulatory science in complex governance. We explore these dynamics in the arena of global sustainability standards for biofuels. We select three institutional fora as sites of inquiry: the European Union's Renewable Energy Directive, the Roundtable on Sustainable Biomaterials, and the International Organization for Standardization. These cases allow us to analyze how the co-production of sustainability science responds to problems of epistemic jurisdiction in the global regulatory order. First, different problems of epistemic jurisdiction beset different standard-setting bodies, and these problems shape both the content of regulatory science and the procedures designed to make it authoritative. Second, in order to produce global regulatory science, technical bodies must manage an array of conflicting imperatives - including scientific virtue, due process and the need to recruit adoptees to perpetuate the standard. At different levels of governance, standard drafters struggle to balance loyalties to country, to company or constituency and to the larger project of internationalization. Confronted with these sometimes conflicting pressures, actors across the standards system quite self-consciously maneuver to build or retain authority for their forum through a combination of scientific adjustment and political negotiation. Third, the evidentiary demands of regulatory science in global administrative spaces are deeply affected by 1) a market for standards, in which firms and states can

  8. Step by Step: Biology Undergraduates' Problem-Solving Procedures during Multiple-Choice Assessment.

    Science.gov (United States)

    Prevost, Luanna B; Lemons, Paula P

    2016-01-01

    This study uses the theoretical framework of domain-specific problem solving to explore the procedures students use to solve multiple-choice problems about biology concepts. We designed several multiple-choice problems and administered them on four exams. We trained students to produce written descriptions of how they solved the problem, and this allowed us to systematically investigate their problem-solving procedures. We identified a range of procedures and organized them as domain general, domain specific, or hybrid. We also identified domain-general and domain-specific errors made by students during problem solving. We found that students use domain-general and hybrid procedures more frequently when solving lower-order problems than higher-order problems, while they use domain-specific procedures more frequently when solving higher-order problems. Additionally, the more domain-specific procedures students used, the higher the likelihood that they would answer the problem correctly, up to five procedures. However, if students used just one domain-general procedure, they were as likely to answer the problem correctly as if they had used two to five domain-general procedures. Our findings provide a categorization scheme and framework for additional research on biology problem solving and suggest several important implications for researchers and instructors. © 2016 L. B. Prevost and P. P. Lemons. CBE—Life Sciences Education © 2016 The American Society for Cell Biology. This article is distributed by The American Society for Cell Biology under license from the author(s). It is available to the public under an Attribution–Noncommercial–Share Alike 3.0 Unported Creative Commons License (http://creativecommons.org/licenses/by-nc-sa/3.0).

  9. Muscle sparing lateral thoracotomy: the standard incision for thoracic procedures

    Directory of Open Access Journals (Sweden)

    Mihai Dumitrescu

    2017-05-01

    Full Text Available Lateral thoracotomy is a versatile approach with many variations and is currently the most widely used incision in thoracic surgery. In the current article we are presenting the muscle-sparing lateral thoracotomy in the lateral decubitus position which we consider to be the “standard” for lateral thoracotomies. Indications, surgical technique and pitfalls are described alongside our experience with thoracic drainage. Although there is no consensus regarding the name of this incision, some authors call it “axillary thoracotomy” while others call it a “modified lateral thoracotomy”, they all agree on one aspect – the importance of muscle sparing – which makes it the go-to thoracotomy for both small and large procedures involving the lung. Lateral muscle sparing thoracotomy allows for good exposure of the pulmonary hilum, fissures, apex and diaphragm. The approach is easy and quick to perform while at the same time ensuring faster postoperative recovery by sparing the latissimus dorsi muscle, better cosmetics and lower postoperative pain score when compared to the posterolateral or classical lateral thoracotomies.

  10. The calibration procedures in the Studsvik standardized personnel dosimetry system

    International Nuclear Information System (INIS)

    Widell, C.O.

    1978-01-01

    Every large nuclear installation in Sweden reads its own personnel TLDs. In order to supervise this decentralized reading of dose meters, the TLD readers are connected by telephone lines to a central computer for dose registration. This computer is used both for registering the personnel doses and for checking the TLD readers. This checking is performed by the use of pre-irradiated calibration dose meters which are always used when a batch of personnel dose meters are read. The pre-irradiated dose meters are either irradiated using 137 Cs to various doses up to 100mSv(10000mrem) or using a 90 Sr source in a reference dose irradiator to a dose equal to 3mSv(300mrem) from a 137 Cs source. The results from the reading of the pre-irradiated dose meters are processed by the computer and a calibration factor is calculated. The calibration factor is automatically used to calculate the doses to the personnel TLD's. However, if the calibration factor deviates by more than 10% from the previously used factor, this fact is shown to the operator - who then has to decide what calibration factor is going to be used. This calibration and supervisory procedure together with the safety interlocks in the TLD readers has resulted in a very reliable and accurate dosimetry system. (author)

  11. Radiation protection problems by diagnostic procedures of pediatric nuclear medicine

    International Nuclear Information System (INIS)

    Kletter, K.

    1994-01-01

    Special dosimetry considerations are necessary in the application of radiopharmaceuticals in pediatric nuclear medicine. The influence of differences in irradiation geometry and biokinetic parameters on the radiation dose in children and adults is discussed. Assuming an equal activity concentration, both factors lead rather to a reduced radiation dose than an increased radiation burden in children compared to adults. However, the same radiation dose in children and adults may lead to a different detriment. This is explained by differences in life expectancy and radiation sensitivity for both groups. From special formulas an age dependent reduction factor can be calculated for the application of radiopharmaceuticals in pediatric nuclear medicine. Radiation exposure to hospital staff and parents from children, undergoing nuclear medicine diagnostic or therapeutic procedures, is low. (author)

  12. Re-analysis of CSNI standard problem, 8

    International Nuclear Information System (INIS)

    Sasaki, Shinobu; Araya, Fumimasa

    1981-12-01

    This report presents the results of computer runs which carried out with the use of ALARM-Pl code. The object of analyses is the Semiscale S-06-3 experiment accepted as the CSNI International Standard Problem 8. According to the preliminary results reported before, the agreement between ALARM-Pl and this experiment was very poor for the key parameters such as the break flow or fuel cladding surface temperature. Hence, much effort has been made to improve the disagreement. Through the re-examination of both the code and input-data, the agreement between the calculated and measured results for key parameters has been much better than that gained in the foregoing test run. (author)

  13. The hierarchy problem of the electroweak standard model revisited

    International Nuclear Information System (INIS)

    Jegerlehner, Fred

    2013-05-01

    A careful renormalization group analysis of the electroweak Standard Model reveals that there is no hierarchy problem in the SM. In the broken phase a light Higgs turns out to be natural as it is self-protected and self-tuned by the Higgs mechanism. It means that the scalar Higgs needs not be protected by any extra symmetry, specifically super symmetry, in order not to be much heavier than the other SM particles which are protected by gauge- or chiral-symmetry. Thus the existence of quadratic cutoff effects in the SM cannot motivate the need for a super symmetric extensions of the SM, but in contrast plays an important role in triggering the electroweak phase transition and in shaping the Higgs potential in the early universe to drive inflation as supported by observation.

  14. The hierarchy problem of the electroweak standard model revisited

    Energy Technology Data Exchange (ETDEWEB)

    Jegerlehner, Fred [Humboldt-Universitaet, Berlin (Germany). Inst. fuer Physik; Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany)

    2013-05-15

    A careful renormalization group analysis of the electroweak Standard Model reveals that there is no hierarchy problem in the SM. In the broken phase a light Higgs turns out to be natural as it is self-protected and self-tuned by the Higgs mechanism. It means that the scalar Higgs needs not be protected by any extra symmetry, specifically super symmetry, in order not to be much heavier than the other SM particles which are protected by gauge- or chiral-symmetry. Thus the existence of quadratic cutoff effects in the SM cannot motivate the need for a super symmetric extensions of the SM, but in contrast plays an important role in triggering the electroweak phase transition and in shaping the Higgs potential in the early universe to drive inflation as supported by observation.

  15. 15 CFR 10.7 - Procedure when a recommended standard is not supported by a consensus.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Procedure when a recommended standard is not supported by a consensus. 10.7 Section 10.7 Commerce and Foreign Trade Office of the Secretary... recommended standard is not supported by a consensus. If the Department determines that a recommended standard...

  16. 10 CFR 440.21 - Weatherization materials standards and energy audit procedures.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 3 2010-01-01 2010-01-01 false Weatherization materials standards and energy audit... FOR LOW-INCOME PERSONS § 440.21 Weatherization materials standards and energy audit procedures. (a...) of this section describes the performance and quality standards for renewable energy systems...

  17. Problems of Soviet procedural law enforcement in 1930s.

    Directory of Open Access Journals (Sweden)

    Alexander Kodintsev

    2017-01-01

    Full Text Available УДК 340.158The subject. Features of the organization of justice and the quality of procedural law enforcement in the USSR in the 1930s.The purpose. The determination of historical patterns of judicial enforcement in the USSR in the 1930s and the identification of the causes of the ineffectiveness of the proceedings in this period.Methodology. The author uses historical legal method, formal legal interpretation of statutes, the method of analysis of judicial statistics.Results, scope of application. After the criminal law campaigns of the early 1930s the judg-ment in the Soviet Union was in a disturbed condition. The Soviet civil process was almost absolutely eliminated. Tens thousands materials of court cases were lost throughout the Union every year. The courts were extremely busy.The courts used accusatory approach. The petitions of the accused were almost never solved. Prisoners were not handed copies of the indictments.During the terror of the old evils of the judicial system worsened, the destruction of the judicial process began. The timeframe for completing cases increased. Almost half of criminal cases in case of complaint (appeal has been revised by the higher courts. The courts again applied the simplified procedure.At the end of the 1930s the procedural regulation of the judicial work was the duty of People's Commissariat of Justice of the USSR and of the Supreme Court of the USSR. USSR Supreme Court continued to take decisions in litigation in the plenums. The Boards of Su-preme Court examines cases influencing law of practice.The quality of judgment by the Supreme Courts of the Republics of Soviet Union in the late 1930s did not change significantly in comparison with the previous period. This was due to constant staff turnover and low level of qualification of judges. The Supreme Courts of the Republics had no Plenum, so they could influence law of practice by the rulings of of the Boards. These rulings were extremely ignorant

  18. Standardization of figures and assessment procedures for DTM verticalaccuracy

    Directory of Open Access Journals (Sweden)

    Vittorio Casella

    2015-07-01

    Full Text Available Digital Terrain Models (DTMs are widely used in many sectors. They play a key role in hydrological risk prevention, risk mitigation and numeric simulations. This paper deals with two questions: (i when it is stated that a DTM has a given vertical accuracy, is this assertion univocal? (ii when DTM vertical accuracy is assessed by means of checkpoints, does their location influence results? First, the paper illustrates that two vertical accuracy definitions are conceivable: Vertical Accuracy at the Nodes (VAN, the average vertical distance between the model and the terrain, evaluated at the DTM's nodes and Vertical Accuracy at the interpolated Points (VAP, in which the vertical distance is evaluated at the generic points. These two quantities are not coincident and, when they are calculated for the same DTM, different numeric values are reached. Unfortunately, the two quantities are often interchanged, but this is misleading. Second, the paper shows a simulated example of a DTM vertical accuracy assessment, highlighting that the checkpoints’ location plays a key role: when checkpoints coincide with the DTM nodes, VAN is estimated; when checkpoints are randomly located, VAP is estimated, instead. Third, an in-depth, theoretical characterization of the two considered quantities is performed, based on symbolic computation, and suitable standardization coefficients are proposed. Finally, our discussion has a well-defined frame: it doesn't deal with all the items of the DTM vertical accuracy budget, which would require a much longer essay, but only with one, usually called fundamental vertical accuracy.

  19. Transmission investment problems in Europe: Going beyond standard solutions

    International Nuclear Information System (INIS)

    Buijs, Patrik; Bekaert, David; Cole, Stijn; Van Hertem, Dirk; Belmans, Ronnie

    2011-01-01

    The European transmission grid is facing an investment challenge. There is a strong call for more transmission capacity. At the same time, the investment climate is fierce and troubled by public opposition, a complex regulatory framework, etc. Many transmission capacity expansion projects are delayed or canceled. In this paper different technology options suitable for increasing transmission capacity are discussed. The aim is to provide policy-makers with information on technologies without going too much into technical details. The focus is on opportunities and limitations to implement various technological alternatives in practice, including technical solutions that go beyond constructing new connection lines. The criteria used in this technology assessment are based on the obstacles reported in the European Priority Interconnection Plan. This ensures a realistic approach based on problems encountered in real projects. Although AC overhead lines (OHL) will remain the standard solution for grid expansion, it is argued that different technology options can overcome many obstacles that OHL face. Additionally, it is illustrated that the higher investment costs for some solutions can be offset with an increased benefit, e.g. by accomplishing investments with smaller delays due to fewer obstacles encountered. - Research highlights: → Assessment of real problems encountered in transmission investments. → Comparison of transmission technologies. → Techno-economic evaluation of transmission technologies.

  20. ISP33 standard problem on the PACTEL facility

    Energy Technology Data Exchange (ETDEWEB)

    Purhonen, H.; Kouhia, J. [VTT Energy, Lappeenranta (Finland); Kalli, H. [Lappeenranta Univ. of Technology (Finland)

    1995-09-01

    ISP33 is the first OECD/NEA/CSNI standard problem related to VVER type of pressurized water reactors. The reference reactor of the PACTEL test facility, which was used to carry out the ISP33 experiment, is the VVER-440 reactor, two of which are located near the Finnish city of Loviisa. The objective of the ISP33 test was to study the natural circulation behaviour of VVER-440 reactors at different coolant inventories. Natural circulation was considered as a suitable phenomenon to focus on by the first VVER related ISP due to its importance in most accidents and transients. The behaviour of the natural circulation was expected to be different compared to Western type of PWRs as a result of the effect of horizontal steam generators and the hot leg loop seals. This ISP was conducted as a blind problem. The experiment was started at full coolant inventory. Single-phase natural circulation transported the energy from the core to the steam generators. The inventory was then reduced stepwise at about 900 s intervals draining 60 kg each time from the bottom of the downcomer. the core power was about 3.7% of the nominal value. The test was terminated after the cladding temperatures began to rise. ATHLET, CATHARE, RELAP5 (MODs 3, 2.5 and 2), RELAP4/MOD6, DINAMIKA and TECH-M4 codes were used in 21 pre- and 20 posttest calculations submitted for the ISP33.

  1. Evaluation of nuclear power plant operating procedures classifications and interfaces: Problems and techniques for improvement

    International Nuclear Information System (INIS)

    Barnes, V.E.; Radford, L.R.

    1987-02-01

    This report presents activities and findings of a project designed to evaluate current practices and problems related to procedure classification schemes and procedure interfaces in commercial nuclear power plants. The phrase ''procedure classification scheme'' refers to how plant operating procedures are categorized and indexed (e.g., normal, abnormal, emergency operating procedures). The term ''procedure interface'' refers to how reactor operators are instructed to transition within and between procedures. The project consisted of four key tasks, including (1) a survey of literature regarding problems associated with procedure classifications and interfaces, as well as techniques for overcoming them; (2) interviews with experts in the nuclear industry to discuss the appropriate scope of different classes of operating procedures and techniques for managing interfaces between them; (3) a reanalysis of data gathered about nuclear power plant normal operating and off-normal operating procedures in a related project, ''Program Plan for Assessing and Upgrading Operating Procedures for Nuclear Power Plants''; and (4) solicitation of the comments and expert opinions of a peer review group on the draft project report and on proposed techniques for resolving classification and interface issues. In addition to describing these activities and their results, recommendations for NRC and utility actions to address procedure classification and interface problems are offered

  2. Stiffness analysis for the micromagnetic standard problem No. 4

    International Nuclear Information System (INIS)

    Tsiantos, Vassilios D.; Suess, Dieter; Schrefl, Thomas; Fidler, Josef

    2001-01-01

    In this article solutions to micromagnetic standard problem No. 4, a 500-nmx125-nm-wide NiFe film, are presented. A three-dimensional-finite element simulation based on the solution of the Gilbert equation has been used. The simulations show that two different reversal mechanisms occur for the two different applied fields. For a field at 170 degree counterclockwise from the saturation direction there is a nonuniform rotation of magnetization towards the direction of the applied field, with the magnetization at the ends rotating faster than the magnetization in the center. For a field at 190 degree counterclockwise from the saturation direction the magnetization at the ends and in the center rotate in opposite directions leading to the formation of a 360 degree wall after 0.22 ns associated with a peak in the exchange energy. Moreover, the time for the magnetization component parallel to the long axis to cross the zero is 0.136 and 0.135 ns for field 1 and field 2, respectively. The stiffness of the problem has been investigated solving the system of ordinary differential equations with a nonstiff method (Adams) and a stiff one (backward differentiation formula, BDF). For the measure of stiffness the ratio of the total number of time steps (nst) taken by the two solvers, that is nst(Adams)/nst(BDF), has been used. This ratio is 0.784 for field 1 and 0.593 for field 2, which means that the nonstiff method (Adams) uses larger time steps than the stiff method (BDF) and consequently the systems are not stiff. The average time step for the Adams method was 0.2 ps for both fields. [copyright] 2001 American Institute of Physics

  3. Trends and the determination of effective doses for standard X-ray procedures

    International Nuclear Information System (INIS)

    Johnson, H.M.; Neduzak, C.; Gallet, J.; Sandeman, J.

    2001-01-01

    Trends in the entrance skin exposures (air kerma) for standard x-ray imaging procedures are reported for the Province of Manitoba, Canada. Average annual data per procedure using standard phantoms and standard ion chambers have been recorded since 1981. For example, chest air kerma (backscatter included) has decreased from 0.14 to 0.09 mGy. Confounding factors may negate the gains unless facility quality control programs are maintained. The data were obtained for a quality assurance and regulatory compliance program. Quoting such data for risk evaluation purposes lacks rigor hence a compartment model for organ apportioning, using organ absorbed doses and weighting factors, has been applied to determine effective dose per procedure. The effective doses for the standard procedures are presented, including the value of 0.027 mSv (1999) calculated for the effective dose in PA chest imaging. (author)

  4. Licensing procedure, nuclear codes and standards in the Federal Republic of Germany

    International Nuclear Information System (INIS)

    Schultheiss, G.F.

    1980-01-01

    The present paper deals with legal background of licensing in nuclear technology and atomic energy use, licensing procedures for nuclear power plants and with codes, standards and guidelines in the Federal Republic of Germany. (orig./RW)

  5. 40 CFR 75.38 - Standard missing data procedures for Hg CEMS.

    Science.gov (United States)

    2010-07-01

    ... Hg CEMS. 75.38 Section 75.38 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Standard missing data procedures for Hg CEMS. (a) Once 720 quality assured monitor operating hours of Hg... substitute data for Hg concentration in accordance with the procedures in ( 75.33(b)(1) through (b)(4...

  6. 9 CFR 354.210 - Minimum standards for sanitation, facilities, and operating procedures in official plants.

    Science.gov (United States)

    2010-01-01

    ... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Minimum standards for sanitation, facilities, and operating procedures in official plants. 354.210 Section 354.210 Animals and Animal Products... sanitation, facilities, and operating procedures in official plants. The provisions of §§ 354.210 to 354.247...

  7. Improving the safety and quality of nursing care through standardized operating procedures in Bosnia and Herzegovina.

    Science.gov (United States)

    Ausserhofer, Dietmar; Rakic, Severin; Novo, Ahmed; Dropic, Emira; Fisekovic, Eldin; Sredic, Ana; Van Malderen, Greet

    2016-06-01

    We explored how selected 'positive deviant' healthcare facilities in Bosnia and Herzegovina approach the continuous development, adaptation, implementation, monitoring and evaluation of nursing-related standard operating procedures. Standardized nursing care is internationally recognized as a critical element of safe, high-quality health care; yet very little research has examined one of its key instruments: nursing-related standard operating procedures. Despite variability in Bosnia and Herzegovina's healthcare and nursing care quality, we assumed that some healthcare facilities would have developed effective strategies to elevate nursing quality and safety through the use of standard operating procedures. Guided by the 'positive deviance' approach, we used a multiple-case study design to examine a criterion sample of four facilities (two primary healthcare centres and two hospitals), collecting data via focus groups and individual interviews. In each studied facility, certification/accreditation processes were crucial to the initiation of continuous development, adaptation, implementation, monitoring and evaluation of nursing-related SOPs. In one hospital and one primary healthcare centre, nurses working in advanced roles (i.e. quality coordinators) were responsible for developing and implementing nursing-related standard operating procedures. Across the four studied institutions, we identified a consistent approach to standard operating procedures-related processes. The certification/accreditation process is enabling necessary changes in institutions' organizational cultures, empowering nurses to take on advanced roles in improving the safety and quality of nursing care. Standardizing nursing procedures is key to improve the safety and quality of nursing care. Nursing and Health Policy are needed in Bosnia and Herzegovina to establish a functioning institutional framework, including regulatory bodies, educational systems for developing nurses' capacities or the

  8. A Proposed Model for Selecting Measurement Procedures for the Assessment and Treatment of Problem Behavior.

    Science.gov (United States)

    LeBlanc, Linda A; Raetz, Paige B; Sellers, Tyra P; Carr, James E

    2016-03-01

    Practicing behavior analysts frequently assess and treat problem behavior as part of their ongoing job responsibilities. Effective measurement of problem behavior is critical to success in these activities because some measures of problem behavior provide more accurate and complete information about the behavior than others. However, not every measurement procedure is appropriate for every problem behavior and therapeutic circumstance. We summarize the most commonly used measurement procedures, describe the contexts for which they are most appropriate, and propose a clinical decision-making model for selecting measurement produces given certain features of the behavior and constraints of the therapeutic environment.

  9. Student Opinions about the Seven-Step Procedure in Problem-Based Hospitality Management Education

    Science.gov (United States)

    Zwaal, Wichard; Otting, Hans

    2014-01-01

    This study investigates how hospitality management students appreciate the role and application of the seven-step procedure in problem-based learning. A survey was developed containing sections about personal characteristics, recall of the seven steps, overall report marks, and 30 statements about the seven-step procedure. The survey was…

  10. Standard testing procedures for optical fiber and unshielded twisted pair at Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Adams, R.L.

    1993-11-01

    This document will establish a working standard for testing optical fiber and unshielded twisted pair cables included in the Lab-wide telecommunications cabling system. The purpose of these standard testing procedures is to deliver to all Sandians a reliable, low-maintenance, state-of-the-art, ubiquitous telecommunications cabling infrastructure capable of satisfying all current and future telecommunication needs.

  11. Finite element analyses for seismic shear wall international standard problem

    International Nuclear Information System (INIS)

    Park, Y.J.; Hofmayer, C.H.

    1998-04-01

    Two identical reinforced concrete (RC) shear walls, which consist of web, flanges and massive top and bottom slabs, were tested up to ultimate failure under earthquake motions at the Nuclear Power Engineering Corporation's (NUPEC) Tadotsu Engineering Laboratory, Japan. NUPEC provided the dynamic test results to the OECD (Organization for Economic Cooperation and Development), Nuclear Energy Agency (NEA) for use as an International Standard Problem (ISP). The shear walls were intended to be part of a typical reactor building. One of the major objectives of the Seismic Shear Wall ISP (SSWISP) was to evaluate various seismic analysis methods for concrete structures used for design and seismic margin assessment. It also offered a unique opportunity to assess the state-of-the-art in nonlinear dynamic analysis of reinforced concrete shear wall structures under severe earthquake loadings. As a participant of the SSWISP workshops, Brookhaven National Laboratory (BNL) performed finite element analyses under the sponsorship of the U.S. Nuclear Regulatory Commission (USNRC). Three types of analysis were performed, i.e., monotonic static (push-over), cyclic static and dynamic analyses. Additional monotonic static analyses were performed by two consultants, F. Vecchio of the University of Toronto (UT) and F. Filippou of the University of California at Berkeley (UCB). The analysis results by BNL and the consultants were presented during the second workshop in Yokohama, Japan in 1996. A total of 55 analyses were presented during the workshop by 30 participants from 11 different countries. The major findings on the presented analysis methods, as well as engineering insights regarding the applicability and reliability of the FEM codes are described in detail in this report. 16 refs., 60 figs., 16 tabs

  12. EVALUASI SANITATION STANDARD OPERATING PROCEDURES KERUPUKAMPLANG DI UD SARINA KECAMATAN KALIANGET KABUPATEN SUMENEP

    Directory of Open Access Journals (Sweden)

    Ach Triharjono

    2016-11-01

    Full Text Available Industri pangan untuk menghasilkan produk yang memenuhi standar keamanan pangan. Standar tersebut dapat dipenuhi dengan menerapkan 8 aspek kunci Sanitation Standard Operating Prosedures (SSOP. Tujuan dari penelitian ini adalah untuk memperoleh hasil penerapan 8 aspek kunci Sanitation Standard Operating Procedures (SSOP dan mengevaluasi penerapan Sanitation Standard Operating Procedures (SSOP Di UD Sarina Kecamatan Kalianget Kabupaten Sumenep. Jenis penelitian ini bersifat deskriptif dengan lokasi penelitian di UD Sarina Kecamatan Kalianget Kabupaten Sumenep. Hasil penelitian diketahui bahwa penerapan 8 aspek kunci Sanitation Standard Operating Procedures (SSOP di UD Sarina sudah terlaksana tapi terdapat 3 tahapan kunci yang belum terlaksana dengan baik yaitu pencegahan kontaminasi silang, pengawasan kondisi kesehatan personil dan menghilangkan hama dari unit pengolahan. Hal yang perlu ditingkatkan terkait dengan penerapan SSOP di UD Sarina yaitu masih perlu adanya manual prosedur untuk berbagai pelaksanaan sanitasi yang dilakukan oleh UD Sarina ini

  13. Solving a combined cutting-stock and lot-sizing problem with a column generating procedure

    DEFF Research Database (Denmark)

    Nonås, Sigrid Lise; Thorstenson, Anders

    2008-01-01

    In Nonås and Thorstenson [A combined cutting stock and lot sizing problem. European Journal of Operational Research 120(2) (2000) 327-42] a combined cutting-stock and lot-sizing problem is outlined under static and deterministic conditions. In this paper we suggest a new column generating solutio...... indicate that the procedure works well also for the extended cutting-stock problem with only a setup cost for each pattern change....

  14. Price adjustment for traditional Chinese medicine procedures: Based on a standardized value parity model.

    Science.gov (United States)

    Wang, Haiyin; Jin, Chunlin; Jiang, Qingwu

    2017-11-20

    Traditional Chinese medicine (TCM) is an important part of China's medical system. Due to the prolonged low price of TCM procedures and the lack of an effective mechanism for dynamic price adjustment, the development of TCM has markedly lagged behind Western medicine. The World Health Organization (WHO) has emphasized the need to enhance the development of alternative and traditional medicine when creating national health care systems. The establishment of scientific and appropriate mechanisms to adjust the price of medical procedures in TCM is crucial to promoting the development of TCM. This study has examined incorporating value indicators and data on basic manpower expended, time spent, technical difficulty, and the degree of risk in the latest standards for the price of medical procedures in China, and this study also offers a price adjustment model with the relative price ratio as a key index. This study examined 144 TCM procedures and found that prices of TCM procedures were mainly based on the value of medical care provided; on average, medical care provided accounted for 89% of the price. Current price levels were generally low and the current price accounted for 56% of the standardized value of a procedure, on average. Current price levels accounted for a markedly lower standardized value of acupuncture, moxibustion, special treatment with TCM, and comprehensive TCM procedures. This study selected a total of 79 procedures and adjusted them by priority. The relationship between the price of TCM procedures and the suggested price was significantly optimized (p based on a standardized value parity model is a scientific and suitable method of price adjustment that can serve as a reference for other provinces and municipalities in China and other countries and regions that mainly have fee-for-service (FFS) medical care.

  15. Present problems of standardization in nuclear instrumentation in Romania

    International Nuclear Information System (INIS)

    Purghel, Lidia

    2001-01-01

    The continuos development of nuclear techniques, based on international cooperation, led to the need for producing national and international standards referring to terminology, classification, technical characteristic, testing and calibration methods for nuclear instrumentation. The international standardization activity is organised in the frame of the well-known organization like IEC, ISO, ICRU, ICRP, IOLM, CENELEC, EFOMP, WHO. High advances were obtained in the standardization of the ionising radiation dosimetry in the frame of the International Commission for Radiation Units (ICRU) which started its works 1925. Romania is member of the International Electrotechnical Commission (IEC) from 1920 when its president was the formal member of Romanian Academy, professor Remus Radulet. Romania is effectively involved in standardization activities in the field nuclear instrumentation both as user and manufacturer of nuclear instrumentation. At national level the Technical Committee 45, as a branch of the Romanian Electrotechnical Committee is hosted by Horia Hulubei National Institute for Physics and Nuclear Engineering. The technical committee has the tasks of analysing the market, the regulations and the industry requirements and proposing new standards or revision for existing one. A table is given showing the number of IEC standards considered by TC 45, adopted RS - IEC standards (prepared/published) and planned for 2000/2001. Romania hosted IEC international plenary meetings in 1962 and 1974 and an IEC workshop 1997 with participation of specialists from USA, Sweden, Germany, France, Japan and Romania. As industry is striving to use more and more standard products, that means best quality and safety for less money, more than ever one have to convince the industry about the usefulness and specificity of the nuclear standards

  16. Problems of the development of international standards of “green building” in Russia

    Science.gov (United States)

    Meshcheryakova, Tatiana

    2017-10-01

    Problems of environmental friendliness and energy efficiency in recent decades have become not only the most important issues of economic development of the main industrial economies, but also the basis for the processes of maintaining the security and relative stability of the global ecosystem. The article presents the results of the study of the status and trends of the development of environmental standards for the construction and maintenance of real estate in the world and particularly in Russia. Special market instruments for assessing the compliance with the quality of real estate projects under construction and modern principles of environmental friendliness and energy efficiency include voluntary building certification systems that are actively used in international practice. In Russia there is active use of the following international systems of certification: BREEAM, LEED, DGNB, HQE. Also in the Russian certification market, the national standard STO NOSTROY 2.35.4-2011 “Residential and public buildings” is being implemented, which summarizes the best international experience of the rating evaluation procedure. Comparative characteristics of the “green” standards and the principles of rating assessments of the ecological compatibility of buildings give an idea of applying these standards in Russia.

  17. Fault detection for nonlinear systems - A standard problem approach

    DEFF Research Database (Denmark)

    Stoustrup, Jakob; Niemann, Hans Henrik

    1998-01-01

    The paper describes a general method for designing (nonlinear) fault detection and isolation (FDI) systems for nonlinear processes. For a rich class of nonlinear systems, a nonlinear FDI system can be designed using convex optimization procedures. The proposed method is a natural extension...

  18. Improving the review of standard operating procedures: a novel electronic system for compounding pharmacies.

    Science.gov (United States)

    Brensel, Robert; Brensel, Scott; Ng, Amy

    2013-01-01

    Since the New England Compounding Center disaster in 2012, the importance of following correct procedures during every phase of customized pharmacy has been a focus of governmental interest and action as well as public scrutiny. Many pharmacies rely on the rote review of standard operating procedures to ensure that staff members understand and follow protocols that ensure the safety and potency of all compounds prepared, but that approach to continuing education can be cumbersome and needlessly time-consuming. In addition, documenting and retrieving evidence of employee competence can be difficult. In this article, we describe our use of online technology to improve our methods of educating staff about the full range of standard operating procedures that must be followed in our pharmacy. The system we devised and implemented has proven to be effective, easy to update and maintain, very inexpensive, and user friendly. Its use has reduced the time previously required for a read-over review of standard operating procedures from 30 or 40 minutes to 5 or 10 minutes in weekly staff meetings, and we can now easily document and access proof of employees' comprehension of that content. It is our hope that other small compounding pharmacies will also find this system of online standard operating procedure review helpful.

  19. Standard Guidelines of Care: Performing Procedures in Patients on or Recently Administered with Isotretinoin.

    Science.gov (United States)

    Mysore, Venkataram; Mahadevappa, Omprakash H; Barua, Shyamanta; Majid, Imran; Viswanath, Vishalakshi; Bhat, Ramesh M; Talwar, Suresh; Thurakkal, Salim; Aurangabadkar, Sanjeev J; Chatterjee, Manas; Ganjoo, Anil

    2017-01-01

    Currently, the standard protocol regarding the performance of procedures on patients receiving or having recently received isotretinoin (13- cis -retinoic acid) states that the procedures should not be performed. The recommendations in standard books and drug insert require discontinuation of isotretinoin for 6 months before performing cosmetic procedures, including waxing, dermabrasion, chemical peels, laser procedures, or incisional and excisional cold-steel surgery. These recommendations have been followed for over two decades despite little evidence for the stated increased risk of scarring. The Association of Cutaneous Surgeons (I) constituted a task force to review the evidence and to recommend consensus guidelines regarding the safety of skin procedures, including resurfacing, energy-device treatments, and dermatosurgical procedures in patients with concurrent or recent isotretinoin administration. Data were extracted from the literature through a PubMed search using the keywords "isotretinoin," "safety," "scarring," "keloids," "hypertrophic scarring," and "pigmentation." The evidence was then labeled and circulated to all members of task force for review. The task force is of the opinion that there is insufficient evidence to support the current protocol of avoiding and delaying treatments in the patient group under consideration and recommends that the current practice should be discontinued. The task force concludes that performing procedures such as laser hair removal, fractional lasers for aging and acne scarring, lasers for pigmented skin lesions, fractional radio-frequency microneedling, superficial and medium-depth peels, microdermabrasion, dermaroller, biopsies, radio-frequency ablation, and superficial excisions is safe in patients with concurrent or recent isotretinoin administration.

  20. Procedures for aggregating citizen preferences in the context of the nuclear waste management problem. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Brock, H.W.; Sauer, G.L.

    1978-10-01

    The purpose of the present paper is to provide an introduction to the theory of social choice and related disciplines, and to relate this theory to the concrete problem of nuclear waste management. In Section I of this report, an overview of the problem is provided. In Section II, two candidate preference aggregation procedures that can be used to identify a socially optimal waste management policy are identified. In Section III, a somewhat lengthy defense of the use of these two aggregation procedures is presented. Each is shown to be compatible with four intuitively appealing criteria of collective decision-making. In Section IV the application of one of the procedures to the evaluation of waste management alternatives is discussed. In Section V the problem of inferring evaluation parameters from expert and laypersons' judgments is addressed.

  1. Procedures for aggregating citizen preferences in the context of the nuclear waste management problem. Final report

    International Nuclear Information System (INIS)

    Brock, H.W.; Sauer, G.L.

    1978-10-01

    The purpose of the present paper is to provide an introduction to the theory of social choice and related disciplines, and to relate this theory to the concrete problem of nuclear waste management. In Section I of this report, an overview of the problem is provided. In Section II, two candidate preference aggregation procedures that can be used to identify a socially optimal waste management policy are identified. In Section III, a somewhat lengthy defense of the use of these two aggregation procedures is presented. Each is shown to be compatible with four intuitively appealing criteria of collective decision-making. In Section IV the application of one of the procedures to the evaluation of waste management alternatives is discussed. In Section V the problem of inferring evaluation parameters from expert and laypersons' judgments is addressed

  2. The primary exposure standard for Co-60 gamma radiation: characteristics and measurements procedures

    International Nuclear Information System (INIS)

    Laitano, R.F.; Toni, M.P.

    1983-01-01

    A description is given of a cavity ionization chamber used, as a primary exposure standard, at the Laboratorio di Metrologia delle Radiazioni Ionizzanti of the ENEA in Italy. The primary standard is designed to make absolute measurements of exposure due to the Co-60 gamma radiation. The procedures for the realizationof the exposure unit are also described. Finally results of some international comparisons are reported

  3. Standardization for oxygen isotope ratio measurement - still an unsolved problem.

    Science.gov (United States)

    Kornexl; Werner; Gehre

    1999-07-01

    Numerous organic and inorganic laboratory standards were gathered from nine European and North American laboratories and were analyzed for their delta(18)O values with a new on-line high temperature pyrolysis system that was calibrated using Vienna standard mean ocean water (VSMOW) and standard light Antartic precipitation (SLAP) internationally distributed reference water samples. Especially for organic materials, discrepancies between reported and measured values were high, ranging up to 2 per thousand. The reasons for these discrepancies are discussed and the need for an exact and reliable calibration of existing reference materials, as well as for the establishment of additional organic and inorganic reference materials is stressed. Copyright 1999 John Wiley & Sons, Ltd.

  4. [Problems and ways of solutions to harmonize standards for air pollution].

    Science.gov (United States)

    Avaliani, S L; Novikov, S M; Shashina, T A; Skvortsova, N S; Kislitsin, V A; Mishina, A L

    2012-01-01

    In the article the basic problems of harmonization of domestic regulatory framework of air pollution with the WHO recommendations and normative values adopted in the EU, U.S. and other countries are considered. The important role of health risk analysis methodology in the process of harmonization of regulation and control of air quality has been pointed out. The necessity of radical changes in the structure and content of the basic normative document GN 2.1.6.1338-03 "maximum permissible concentration (MPC) of pollutants in the air of populated areas" has been shown. The algorithm of the procedure that justifies the new list of normative values in the air harmonized with international recommendations and standards of developed countries has been proposed.

  5. Deviation from Standard Inflationary Cosmology and the Problems in Ekpyrosis

    Science.gov (United States)

    Tseng, Chien-Yao

    There are two competing models of our universe right now. One is Big Bang with inflation cosmology. The other is the cyclic model with ekpyrotic phase in each cycle. This paper is divided into two main parts according to these two models. In the first part, we quantify the potentially observable effects of a small violation of translational invariance during inflation, as characterized by the presence of a preferred point, line, or plane. We explore the imprint such a violation would leave on the cosmic microwave background anisotropy, and provide explicit formulas for the expected amplitudes ( alma*l'm') of the spherical-harmonic coefficients. We then provide a model and study the two-point correlation of a massless scalar (the inflaton) when the stress tensor contains the energy density from an infinitely long straight cosmic string in addition to a cosmological constant. Finally, we discuss if inflation can reconcile with the Liouville's theorem as far as the fine-tuning problem is concerned. In the second part, we find several problems in the cyclic/ekpyrotic cosmology. First of all, quantum to classical transition would not happen during an ekpyrotic phase even for superhorizon modes, and therefore the fluctuations cannot be interpreted as classical. This implies the prediction of scale-free power spectrum in ekpyrotic/cyclic universe model requires more inspection. Secondly, we find that the usual mechanism to solve fine-tuning problems is not compatible with eternal universe which contains infinitely many cycles in both direction of time. Therefore, all fine-tuning problems including the flatness problem still asks for an explanation in any generic cyclic models.

  6. 75 FR 60171 - Proposed Information Collection (Credit Underwriting Standards and Procedures for Processing VA...

    Science.gov (United States)

    2010-09-29

    ... DEPARTMENT OF VETERANS AFFAIRS [OMB Control No. 2900-0521] Proposed Information Collection (Credit Underwriting Standards and Procedures for Processing VA Guaranteed Loans) Activity: Comment Request AGENCY... comment on the proposed collection of certain information by the agency. Under the Paperwork Reduction Act...

  7. 78 FR 60379 - Proposed Information Collection (Credit Underwriting Standards and Procedures for Processing VA...

    Science.gov (United States)

    2013-10-01

    ... DEPARTMENT OF VETERANS AFFAIRS [OMB Control No. 2900-0521] Proposed Information Collection (Credit Underwriting Standards and Procedures for Processing VA Guaranteed Loans) Activity: Comment Request AGENCY... comment on the proposed collection of certain information by the agency. Under the Paperwork Reduction Act...

  8. 75 FR 76082 - Agency Information Collection (Credit Underwriting Standards and Procedures for Processing VA...

    Science.gov (United States)

    2010-12-07

    ... DEPARTMENT OF VETERANS AFFAIRS [OMB Control No. 2900-0521] Agency Information Collection (Credit Underwriting Standards and Procedures for Processing VA Guaranteed Loans) Activity Under OMB Review AGENCY... information abstracted below to the Office of Management and Budget (OMB) for review and comment. The PRA...

  9. Evolution of standardized procedures for adjusting lumber properties for change in moisture content

    Science.gov (United States)

    David W. Green; James W. Evans

    2001-01-01

    This paper documents the development of procedures in American Society for Testing and Materials standards for adjusting the allowable properties of lumber for changes in moisture content. The paper discusses the historical context of efforts to establish allowable properties on a consensus basis, beginning in the 19th century. Where possible, the reasons for proposed...

  10. Standard operating procedures for female orgasmic disorder: consensus of the International Society for Sexual Medicine

    NARCIS (Netherlands)

    Laan, Ellen; Rellini, Alessandra H.; Barnes, Tricia

    2013-01-01

    As the field of sexual medicine evolves, it is important to continually improve patient care by developing contemporary "standard operating procedures" (SOPs), reflecting the consensus view of experts in sexual medicine. Few, if any, consensus SOPs have been developed for the diagnosis and treatment

  11. Teachers' Use of a Self-Assessment Procedure: The Role of Criteria, Standards, Feedback and Reflection

    Science.gov (United States)

    van Diggelen, Migchiel; den Brok, Perry; Beijaard, Douwe

    2013-01-01

    This article reports on the way teachers assess their own coaching competencies regarding the development of vocational education students' reflection skills. The participating teachers used a self-assessment procedure in which they had to judge themselves with the help of criteria and standards, received feedback from a colleague based on the…

  12. Teachers' use of a self-assessment procedure : the role of criteria, standards, feedback and reflection

    NARCIS (Netherlands)

    Diggelen, van M.R.; Brok, den P.J.; Beijaard, D.

    2013-01-01

    This article reports on the way teachers assess their own coaching competencies regarding the development of vocational education students’ reflection skills. The participating teachers used a self-assessment procedure in which they had to judge themselves with the help of criteria and standards,

  13. A goal programming procedure for solving fuzzy multiobjective fractional linear programming problems

    Directory of Open Access Journals (Sweden)

    Tunjo Perić

    2014-12-01

    Full Text Available This paper presents a modification of Pal, Moitra and Maulik's goal programming procedure for fuzzy multiobjective linear fractional programming problem solving. The proposed modification of the method allows simpler solving of economic multiple objective fractional linear programming (MOFLP problems, enabling the obtained solutions to express the preferences of the decision maker defined by the objective function weights. The proposed method is tested on the production planning example.

  14. Experimental verification for standard analysis procedure of 241Am in food

    International Nuclear Information System (INIS)

    Liu Qingfen; Zhu Hongda; Liu Shutian; Pan Jingshun; Yang Dating

    2005-01-01

    Objective: The briefly experimental verification for 'determination of 241 Am in food' has been described. Methods: The overall recovery, the MDL of method and decontamination experiment has been done by standard analysis procedure. Results: The overall recovery is 76.26 ± 4.1%. The MDL is 3.4 x 10 -5 Bq/g ash, decontamination factor is higher than 10 3 for Po, 10 2 for U, Th, Pu and 60 for 237 Np. Conclusion: The results showed that the overall recovery is quite high and reliable, the MDL of method is able to meet examining 241 Am limited values in foods. the obtained decontamination factors of recommended procedure can meet analysis of 241 Am in food examination. Venifying results of the procedure are satisfied by using 243 Am spike and 241 Am standard reference material. (authors)

  15. The hierarchy problem and Physics Beyond the Standard Model

    Indian Academy of Sciences (India)

    boson. Without the Higgs, theory is not unitary. Gautam Bhattacharyya ... highest scale of the theory. Thus physics at several orders of ... Hu. ≃ −|μ2| + O(1) m2. ˜t mh ≃ 125 GeV ⇒ m˜t ∼ few TeV ⇒ large cancellation ⇒ little hierarchy problem. Large mt drives M. 2. Hu negative. EWSB dynamically triggered by RG. 2. 4. 6. 8.

  16. Procedures and Standards for Residential Ventilation System Commissioning: An Annotated Bibliography

    Energy Technology Data Exchange (ETDEWEB)

    Stratton, J. Chris [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Wray, Craig P. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2013-04-01

    Beginning with the 2008 version of Title 24, new homes in California must comply with ANSI/ASHRAE Standard 62.2-2007 requirements for residential ventilation. Where installed, the limited data available indicate that mechanical ventilation systems do not always perform optimally or even as many codes and forecasts predict. Commissioning such systems when they are installed or during subsequent building retrofits is a step towards eliminating deficiencies and optimizing the tradeoff between energy use and acceptable IAQ. Work funded by the California Energy Commission about a decade ago at Berkeley Lab documented procedures for residential commissioning, but did not focus on ventilation systems. Since then, standards and approaches for commissioning ventilation systems have been an active area of work in Europe. This report describes our efforts to collect new literature on commissioning procedures and to identify information that can be used to support the future development of residential-ventilation-specific procedures and standards. We recommend that a standardized commissioning process and a commissioning guide for practitioners be developed, along with a combined energy and IAQ benefit assessment standard and tool, and a diagnostic guide for estimating continuous pollutant emission rates of concern in residences (including a database that lists emission test data for commercially-available labeled products).

  17. Standard operating procedures improve acute neurologic care in a sub-Saharan African setting.

    Science.gov (United States)

    Jaiteh, Lamin E S; Helwig, Stefan A; Jagne, Abubacarr; Ragoschke-Schumm, Andreas; Sarr, Catherine; Walter, Silke; Lesmeister, Martin; Manitz, Matthias; Blaß, Sebastian; Weis, Sarah; Schlund, Verena; Bah, Neneh; Kauffmann, Jil; Fousse, Mathias; Kangankan, Sabina; Ramos Cabrera, Asmell; Kronfeld, Kai; Ruckes, Christian; Liu, Yang; Nyan, Ousman; Fassbender, Klaus

    2017-07-11

    Quality of neurologic emergency management in an under-resourced country may be improved by standard operating procedures (SOPs). Neurologic SOPs were implemented in a large urban (Banjul) and a small rural (Brikama) hospital in the Gambia. As quality indicators of neurologic emergency management, performance of key procedures was assessed at baseline and in the first and second implementation years. At Banjul, 100 patients of the first-year intervention group exhibited higher rates of general procedures of emergency management than 105 control patients, such as neurologic examination (99.0% vs 91.4%; p process quality of neurologic emergency management in under-resourced settings. This study provides Class IV evidence that, for patients with suspected neurologic emergencies in sub-Saharan Africa, neurologic SOPs increase the rate of performance of guideline-recommended procedures. Copyright © 2017 The Author(s). Published by Wolters Kluwer Health, Inc. on behalf of the American Academy of Neurology.

  18. Standard procedures for adults in accredited sleep medicine centres in Europe

    DEFF Research Database (Denmark)

    Fischer, Jürgen; Dogas, Zoran; Bassetti, Claudio L

    2012-01-01

    The present paper describes standardized procedures within clinical sleep medicine. As such, it is a continuation of the previously published European guidelines for the accreditation of sleep medicine centres and European guidelines for the certification of professionals in sleep medicine, aimed...... at creating standards of practice in European sleep medicine. It is also part of a broader action plan of the European Sleep Research Society, including the process of accreditation of sleep medicine centres and certification of sleep medicine experts, as well as publishing the Catalogue of Knowledge...... and Skills for sleep medicine experts (physicians, non-medical health care providers, nurses and technologists), which will be a basis for the development of relevant educational curricula. In the current paper, the standard operational procedures sleep medicine centres regarding the diagnostic...

  19. Development of Procedures to Assess Problem-Solving Competence in Computing Engineering

    Science.gov (United States)

    Pérez, Jorge; Vizcarro, Carmen; García, Javier; Bermúdez, Aurelio; Cobos, Ruth

    2017-01-01

    In the context of higher education, a competence may be understood as the combination of skills, knowledge, attitudes, values, and abilities that underpin effective and/or superior performance in a professional area. The aim of the work reported here was to design a set of procedures to assess a transferable competence, i.e., problem solving, that…

  20. Updating QR factorization procedure for solution of linear least squares problem with equality constraints.

    Science.gov (United States)

    Zeb, Salman; Yousaf, Muhammad

    2017-01-01

    In this article, we present a QR updating procedure as a solution approach for linear least squares problem with equality constraints. We reduce the constrained problem to unconstrained linear least squares and partition it into a small subproblem. The QR factorization of the subproblem is calculated and then we apply updating techniques to its upper triangular factor R to obtain its solution. We carry out the error analysis of the proposed algorithm to show that it is backward stable. We also illustrate the implementation and accuracy of the proposed algorithm by providing some numerical experiments with particular emphasis on dense problems.

  1. Solving the Standard Model Problems in Softened Gravity

    CERN Document Server

    Salvio, Alberto

    2016-11-16

    The Higgs naturalness problem is solved if the growth of Einstein's gravitational interaction is softened at an energy $ \\lesssim 10^{11}\\,$GeV (softened gravity). We work here within an explicit realization where the Einstein-Hilbert Lagrangian is extended to include terms quadratic in the curvature and a non-minimal coupling with the Higgs. We show that this solution is preserved by adding three right-handed neutrinos with masses below the electroweak scale, accounting for neutrino oscillations, dark matter and the baryon asymmetry. The smallness of the right-handed neutrino masses (compared to the Planck scale) and the QCD $\\theta$-term are also shown to be natural. We prove that a possible gravitational source of CP violation cannot spoil the model, thanks to the presence of right-handed neutrinos. Starobinsky inflation can occur in this context, even if we live in a metastable vacuum.

  2. Standard Guidelines of Care: Performing Procedures in Patients on or Recently Administered with Isotretinoin

    Science.gov (United States)

    Mysore, Venkataram; Mahadevappa, Omprakash H.; Barua, Shyamanta; Majid, Imran; Viswanath, Vishalakshi; Bhat, Ramesh M.; Talwar, Suresh; Thurakkal, Salim; Aurangabadkar, Sanjeev J.; Chatterjee, Manas; Ganjoo, Anil

    2017-01-01

    Background: Currently, the standard protocol regarding the performance of procedures on patients receiving or having recently received isotretinoin (13-cis-retinoic acid) states that the procedures should not be performed. The recommendations in standard books and drug insert require discontinuation of isotretinoin for 6 months before performing cosmetic procedures, including waxing, dermabrasion, chemical peels, laser procedures, or incisional and excisional cold-steel surgery. These recommendations have been followed for over two decades despite little evidence for the stated increased risk of scarring. Objective: The Association of Cutaneous Surgeons (I) constituted a task force to review the evidence and to recommend consensus guidelines regarding the safety of skin procedures, including resurfacing, energy-device treatments, and dermatosurgical procedures in patients with concurrent or recent isotretinoin administration. Materials and Methods: Data were extracted from the literature through a PubMed search using the keywords “isotretinoin,” “safety,” “scarring,” “keloids,” “hypertrophic scarring,” and “pigmentation.” The evidence was then labeled and circulated to all members of task force for review. Results: The task force is of the opinion that there is insufficient evidence to support the current protocol of avoiding and delaying treatments in the patient group under consideration and recommends that the current practice should be discontinued. The task force concludes that performing procedures such as laser hair removal, fractional lasers for aging and acne scarring, lasers for pigmented skin lesions, fractional radio-frequency microneedling, superficial and medium-depth peels, microdermabrasion, dermaroller, biopsies, radio-frequency ablation, and superficial excisions is safe in patients with concurrent or recent isotretinoin administration. PMID:29491653

  3. Standard guidelines of care: Performing procedures in patients on or recently administered with isotretinoin

    Directory of Open Access Journals (Sweden)

    Venkataram Mysore

    2017-01-01

    Full Text Available Background: Currently, the standard protocol regarding the performance of procedures on patients receiving or having recently received isotretinoin (13-cis-retinoic acid states that the procedures should not be performed. The recommendations in standard books and drug insert require discontinuation of isotretinoin for 6 months before performing cosmetic procedures, including waxing, dermabrasion, chemical peels, laser procedures, or incisional and excisional cold-steel surgery. These recommendations have been followed for over two decades despite little evidence for the stated increased risk of scarring. Objective: The Association of Cutaneous Surgeons (I constituted a task force to review the evidence and to recommend consensus guidelines regarding the safety of skin procedures, including resurfacing, energy-device treatments, and dermatosurgical procedures in patients with concurrent or recent isotretinoin administration. Materials and Methods: Data were extracted from the literature through a PubMed search using the keywords “isotretinoin,” “safety,” “scarring,” “keloids,” “hypertrophic scarring,” and “pigmentation.” The evidence was then labeled and circulated to all members of task force for review. Results: The task force is of the opinion that there is insufficient evidence to support the current protocol of avoiding and delaying treatments in the patient group under consideration and recommends that the current practice should be discontinued.The task force concludes that performing procedures such as laser hair removal, fractional lasers for aging and acne scarring, lasers for pigmented skin lesions, fractional radio-frequency microneedling, superficial and medium-depth peels, microdermabrasion, dermaroller, biopsies, radio-frequency ablation, and superficial excisions is safe in patients with concurrent or recent isotretinoin administration.

  4. Implementation of Treatment Integrity Procedures An Analysis of Outcome Studies of Youth Interventions Targeting Externalizing Behavioral Problems

    NARCIS (Netherlands)

    Goense, Pauline; Boendermaker, Leonieke; van Yperen, Tom; Stams, Geert-Jan; van Laar, Jose

    2014-01-01

    This systematic review evaluates the implementation of treatment integrity procedures in outcome studies of youth interventions targeting behavioral problems. The Implementation of Treatment Integrity Procedures Scale (ITIPS), developed by Perepletchikova, Treat, and Kazdin (2007), was adapted

  5. Performance of the Seven-step Procedure in Problem-based Hospitality Management Education

    Directory of Open Access Journals (Sweden)

    Wichard Zwaal

    2016-12-01

    Full Text Available The study focuses on the seven-step procedure (SSP in problem-based learning (PBL. The way students apply the seven-step procedure will help us understand how students work in a problem-based learning curriculum. So far, little is known about how students rate the performance and importance of the different steps, the amount of time they spend on each step and the perceived quality of execution of the procedure. A survey was administered to a sample of 101 students enrolled in a problem-based hospitality management program. Results show that students consider step 6 (Collect additional information outside the group to be most important. The highest performance-rating is for step two (Define the problem and the lowest for step four (Draw a systemic inventory of explanations from step three. Step seven is classified as low in performance and high in importance implicating urgent attention. The average amount of time spent on the seven steps is 133 minutes with the largest part of the time spent on self-study outside the group (42 minutes. The assessment of the execution of a set of specific guidelines (the Blue Card did not completely match with the overall performance ratings for the seven steps. The SSP could be improved by reducing the number of steps and incorporating more attention to group dynamics.

  6. The actual problems of the standardization of magnetically hard materials and permanent magnets

    International Nuclear Information System (INIS)

    Kurbatov, P.A.; Podolskiy, I.D.

    1998-01-01

    The standardization of industrial products raises their accordance with functional purpose, contributes to technological developments and the elimination of technical barriers in trade. The progress of the world trade necessitates the certification of permanent magnets and their manufacturing methods. According to ISO/IEC recommendations, the certification standards should contain the clear requirements to operation parameters of products, that can be impartially controlled. The testing procedures should be clearly formulated and assure that the results may be reproduced. This calls for creation of a system of interconnected certification standards: the standard for technical characteristics of prospective commercial magnetically hard materials, the standard specifications for permanent magnets, the standards for typical testing procedures and the standards for metrological assurance of measurements. (orig.)

  7. Standard and procedures for measuring and evaluating of the field electromagnetic signals

    International Nuclear Information System (INIS)

    Fallas Cordero, Oscar

    2007-01-01

    Rules and procedures are developed for measuring the intensity of electromagnetic field signals produced by public commercial broadcasters. International and national standards applicable to existing broadcasting area were investigated. The Manual para la Comprobacion Tecnica de las Emisiones of the International Radio Consultative Committee of the International Telecommunications Union was used for reference in the procedures. It was worked in coordination with the Control Nacional de Radio and Radio U to obtain information and to study the teams to present a measurement system for laboratory that meets with the standards suggested and which can encompass a wide range of transmission services. Finally agreed with the analysis and research work done, a series of recommendations were made for improvement, which are considered to implement them in medium and long time. (author) [es

  8. Standard audit procedure for continuous emission monitors and ambient air monitoring instruments

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2009-06-15

    The instruments were published in an operational policy manual in 2009. This policy aims to introduce standard audit criteria that can be used to determine if continuous emission monitors and ambient air monitoring devices are operating within acceptable parameters. Before delivering upscale points of the instrument to be audited, each one of the audit equipment used in the field is required to be at normal operating conditions. Before the beginning of the audit, each one of the meteorological and flow measurement equipment is required to be conditioned to current conditions. If the audit fails, the instrument will have to be audited quarterly. The establishment of specific procedures based on instrument manufacturer or certifying body operational standards is required in the case of non-continuous monitoring instruments presenting operational principles outside of the audit procedures listed in the document.

  9. Conceptual and procedural knowledge community college students use when solving a complex science problem

    Science.gov (United States)

    Steen-Eibensteiner, Janice Lee

    2006-07-01

    A strong science knowledge base and problem solving skills have always been highly valued for employment in the science industry. Skills currently needed for employment include being able to problem solve (Overtoom, 2000). Academia also recognizes the need for effectively teaching students to apply problem solving skills in clinical settings. This thesis investigates how students solve complex science problems in an academic setting in order to inform the development of problem solving skills for the workplace. Students' use of problem solving skills in the form of learned concepts and procedural knowledge was studied as students completed a problem that might come up in real life. Students were taking a community college sophomore biology course, Human Anatomy & Physiology II. The problem topic was negative feedback inhibition of the thyroid and parathyroid glands. The research questions answered were (1) How well do community college students use a complex of conceptual knowledge when solving a complex science problem? (2) What conceptual knowledge are community college students using correctly, incorrectly, or not using when solving a complex science problem? (3) What problem solving procedural knowledge are community college students using successfully, unsuccessfully, or not using when solving a complex science problem? From the whole class the high academic level participants performed at a mean of 72% correct on chapter test questions which was a low average to fair grade of C-. The middle and low academic participants both failed (F) the test questions (37% and 30% respectively); 29% (9/31) of the students show only a fair performance while 71% (22/31) fail. From the subset sample population of 2 students each from the high, middle, and low academic levels selected from the whole class 35% (8/23) of the concepts were used effectively, 22% (5/23) marginally, and 43% (10/23) poorly. Only 1 concept was used incorrectly by 3/6 of the students and identified as

  10. How to develop a Standard Operating Procedure for sorting unfixed cells

    Science.gov (United States)

    Schmid, Ingrid

    2012-01-01

    Written Standard Operating Procedures (SOPs) are an important tool to assure that recurring tasks in a laboratory are performed in a consistent manner. When the procedure covered in the SOP involves a high-risk activity such as sorting unfixed cells using a jet-in-air sorter, safety elements are critical components of the document. The details on sort sample handling, sorter set-up, validation, operation, troubleshooting, and maintenance, personal protective equipment (PPE), and operator training, outlined in the SOP are to be based on careful risk assessment of the procedure. This review provides background information on the hazards associated with sorting of unfixed cells and the process used to arrive at the appropriate combination of facility design, instrument placement, safety equipment, and practices to be followed. PMID:22381383

  11. How to develop a standard operating procedure for sorting unfixed cells.

    Science.gov (United States)

    Schmid, Ingrid

    2012-07-01

    Written standard operating procedures (SOPs) are an important tool to assure that recurring tasks in a laboratory are performed in a consistent manner. When the procedure covered in the SOP involves a high-risk activity such as sorting unfixed cells using a jet-in-air sorter, safety elements are critical components of the document. The details on sort sample handling, sorter set-up, validation, operation, troubleshooting, and maintenance, personal protective equipment (PPE), and operator training, outlined in the SOP are to be based on careful risk assessment of the procedure. This review provides background information on the hazards associated with sorting of unfixed cells and the process used to arrive at the appropriate combination of facility design, instrument placement, safety equipment, and practices to be followed. Copyright © 2012 Elsevier Inc. All rights reserved.

  12. Problems with the implementation of international standards for financial reporting and international audit standards

    OpenAIRE

    Dimitrova, Janka

    2012-01-01

    The International Financial Reporting Standards (IFRS) are designed for application in the financial reports with general purpose and the other financial reporting in all profit-oriented entities. The International Auditing Standards (IAS) are setting out the framework for carrying out the review process of financial reporting from entities referred to audit in order to verify the authenticity of the information and raising up the credibility of financial statements. Quality implementation...

  13. Poor compliance with standard precautions against infections during minor gynaecological procedures.

    Science.gov (United States)

    Maharaj, Dushyant; Lawton, Beverley; Garrett, Sue

    2012-06-01

    Splash injuries occurring during minor surgical procedures are associated with a significant infective risk to the operator. It is a common misconception that minor operations carry low risks. To determine the prevalence of the practice of Standard Precautions by medical staff in the obstetric and gynaecology (O & G) units of two hospitals in New Zealand, and to assess self-observed splash injury rates. A cross-sectional survey of all doctors working in the O & G units of two public hospitals servicing a population of 435 000. A self-administered questionnaire was provided to 43 doctors with questions related to the use of Standard Precautions, perceived likelihood of infection from a splash and splash injuries sustained during procedures. The response rate was 76.6% (n = 33/43). Of the respondents, only 30.3% (n = 10) used Standard Precautions during minor procedures. Sixty-four per cent (n = 21) routinely used goggles/visor for eye protection. Forty-five per cent (n = 15) thought they were likely to get an infection from a splash, and 55% (n = 18) of clinicians had experienced a splash injury. Of the minor procedures during which splash injuries had occurred, repair of episiotomy 45.8% (n = 11) was the commonest. This survey shows poor compliance with guidelines for Standard Precautions to protect from infection despite self-reported rates of splash injury being high at 55%. Effective interventions are needed to increase compliance and prevent infection. © 2012 The Authors ANZJOG © 2012 The Royal Australian and New Zealand College of Obstetricians and Gynaecologists.

  14. Procedure and reference standard to determine the structural resolution in coordinate metrology

    Science.gov (United States)

    Illemann, Jens; Bartscher, Markus; Jusko, Otto; Härtig, Frank; Neuschaefer-Rube, Ulrich; Wendt, Klaus

    2014-06-01

    A new procedure and reference standards for specifying the structural resolution in coordinate metrology traceable to the SI unit the metre are proposed. With the definition of the structural resolution, a significant gap will be closed to complete ‘acceptance and verification tests’ of the coordinate measuring systems (CMSs) which are specified in the ISO 10360 series dealing with tactile sensors, optical sensors, and x-ray computed tomography measurement systems (CTs). The proposed new procedure uses reference standards with circular rounded edges. The idea is to measure the radius of curvature on a calibrated round edge structure. From the deviation between the measured and the calibrated radius, an analogue Gaussian broadening of the measurement system is determined. This value is a well-defined and easy-to-apply measure to define the structural resolution for dimensional measurements. It is applicable to CMSs which are based on different sensing principles, e.g. tactile, optical and CT systems. On the other hand, it has a physical meaning similar to the classical optical point-spread function. It makes it possible to predict which smallest details the CMS is capable of measuring reliably for an arbitrary object shape. The theoretical background of the new procedure is given, an appropriate reference standard is described and comparative, quantitative measurement data of CMSs featuring different sensors are shown.

  15. Judicial problems in connection with preliminary decision and construction design approval in nuclear licensing procedures

    International Nuclear Information System (INIS)

    Schmieder, K.

    1977-01-01

    Standardization in nuclear engineering makes two demands on a legal instrument which is to make this standardization possible and which is to promote standardization in the nuclear licensing practice: On the basis of just one licence for a constructional part or a component, its applicability in any number of subsequent facility licensing procedures has to be warranted, and by virtue of its binding effect, standardization has to create a sufficiently big confidence protection with manufacturers, constructioneers and operators to offer sufficiently effective incentives for standardization. The nuclear preliminary decision pursuant to section 7 a of the Atomic Energy Act in the form of the component preliminary decision appears to be unsuitable as a legal instrument for standardization, as the preliminary decision refers exclusively to the construction of a concrete facility. For standardization in reactor engineering, the construction design approval appears to be basically the proper legal instrument on account of its legal structure as well as its economic effect. Its binding effect encouters a limitation with regard to third parties in so far that this limitation could question again the binding effect in a subsequent site-dependent nuclear licence procedure. The legal structure of the extent of the binding effect, which is decisive for the suitability of the construction design approval, lies with the legislator. The following questions have to be regulated: Ought the applicant to have a legal claim on the granting of a construction design approval, or ought it to be at the discretion of the authorities, and secondly, the extent of the binding effect in terms of time on the basis of the fixation of a time limit, or on the basis of the possibility of subsequent conditions to be imposed, or the revocation. (orig./HP) [de

  16. Chapter 8. Medical procedures. Recommendations and standard operating procedures for intensive care unit and hospital preparations for an influenza epidemic or mass disaster

    NARCIS (Netherlands)

    Zimmerman, Janice L.; Sprung, Charles L.; Christian, Michael D.; Camargo, Ruben; Ceraso, Daniel; Azoulay, Elie; Duguet, Alexandre; Guery, Benoit; Reinhart, Konrad; Adini, Bruria; Barlavie, Yaron; Benin-Goren, Odeda; Cohen, Robert; Klein, Motti; Leoniv, Yuval; Margalit, Gila; Rubinovitch, Bina; Sonnenblick, Moshe; Steinberg, Avraham; Weissman, Charles; Wolff, Donna; Kesecioglu, Jozef; de Jong, Menno; Moreno, Rui; An, Youzhong; Du, Bin; Joynt, Gavin M.; Colvin, John; Loo, Shi; Richards, Guy; Artigas, Antonio; Pugin, Jerome; Amundson, Dennis; Devereaux, Asha; Beigel, John; Danis, Marion; Farmer, Chris; Hick, John L.; Maki, Dennis; Masur, Henry; Rubinson, Lewis; Sandrock, Christian; Talmor, Daniel; Truog, Robert; Zimmerman, Janice; Brett, Steve; Montgomery, Hugh; Rhodes, Andrew; Sanderson, Frances; Taylor, Bruce

    2010-01-01

    To provide recommendations and standard operating procedures for intensive care unit and hospital preparations for an influenza pandemic or mass disaster with a specific focus on ensuring that adequate resources are available and appropriate protocols are developed to safely perform procedures in

  17. Business transactions and standards. Towards a system of concepts and a method for early problem identification in standard implementation projects

    NARCIS (Netherlands)

    Rukanova, B.D.

    2005-01-01

    To summarize, with respect to research question one we constructed a system of concepts, while in answer to research question two we proposed a method of how to apply this system of concepts in practice in order to identify potential problems in early stages of standard implementation projects.

  18. A Pareto archive floating search procedure for solving multi-objective flexible job shop scheduling problem

    Directory of Open Access Journals (Sweden)

    J. S. Sadaghiani

    2014-04-01

    Full Text Available Flexible job shop scheduling problem is a key factor of using efficiently in production systems. This paper attempts to simultaneously optimize three objectives including minimization of the make span, total workload and maximum workload of jobs. Since the multi objective flexible job shop scheduling problem is strongly NP-Hard, an integrated heuristic approach has been used to solve it. The proposed approach was based on a floating search procedure that has used some heuristic algorithms. Within floating search procedure utilize local heuristic algorithms; it makes the considered problem into two sections including assigning and sequencing sub problem. First of all search is done upon assignment space achieving an acceptable solution and then search would continue on sequencing space based on a heuristic algorithm. This paper has used a multi-objective approach for producing Pareto solution. Thus proposed approach was adapted on NSGA II algorithm and evaluated Pareto-archives. The elements and parameters of the proposed algorithms were adjusted upon preliminary experiments. Finally, computational results were used to analyze efficiency of the proposed algorithm and this results showed that the proposed algorithm capable to produce efficient solutions.

  19. 40 CFR 75.33 - Standard missing data procedures for SO2, NOX, Hg, and flow rate.

    Science.gov (United States)

    2010-07-01

    ... SO2, NOX, Hg, and flow rate. 75.33 Section 75.33 Protection of Environment ENVIRONMENTAL PROTECTION... Procedures § 75.33 Standard missing data procedures for SO2, NOX, Hg, and flow rate. (a) Following initial...—Missing Data Procedure for SO2 CEMS, CO2 CEMS, Moisture CEMS, Hg CEMS, and Diluent (CO2 or O2) Monitors...

  20. Standardization of specifications and inspection procedures for LEU plate-type research reactor fuels

    International Nuclear Information System (INIS)

    1988-06-01

    With the transition to high density uranium LEU fuel, fabrication costs of research reactor fuel elements have a tendency to increase because of two reasons. First, the amount of the powder of the uranium compound required increases by more than a factor of five. Second, fabrication requirements are in many cases nearer the fabrication limits. Therefore, it is important that measures be undertaken to eliminate or reduce unnecessary requirements in the specification or inspection procedures of research reactor fuel elements utilizing LEU. An additional stimulus for standardizing specifications and inspection procedures at this time is provided by the fact that most LEU conversions will occur within a short time span, and that nearly all of them will require preparation of new specifications and inspection procedures. In this sense, the LEU conversions offer an opportunity for improving the rationality and efficiency of the fuel fabrication and inspection processes. This report focuses on the standardization of specifications and inspection processes of high uranium density LEU fuels for research reactors. However, in many cases the results can also be extended directly to other research reactor fuels. 15 refs, 1 fig., 3 tabs

  1. [Procedure of seed quality testing and seed grading standard of Prunus humilis].

    Science.gov (United States)

    Wen, Hao; Ren, Guang-Xi; Gao, Ya; Luo, Jun; Liu, Chun-Sheng; Li, Wei-Dong

    2014-11-01

    So far there exists no corresponding quality test procedures and grading standards for the seed of Prunus humilis, which is one of the important source of base of semen pruni. Therefor we set up test procedures that are adapt to characteristics of the P. humilis seed through the study of the test of sampling, seed purity, thousand-grain weight, seed moisture, seed viability and germination percentage. 50 cases of seed specimens of P. humilis tested. The related data were analyzed by cluster analysis. Through this research, the seed quality test procedure was developed, and the seed quality grading standard was formulated. The seed quality of each grade should meet the following requirements: for first grade seeds, germination percentage ≥ 68%, thousand-grain weight 383 g, purity ≥ 93%, seed moisture ≤ 5%; for second grade seeds, germination percentage ≥ 26%, thousand-grain weight ≥ 266 g, purity ≥ 73%, seed moisture ≤9%; for third grade seeds, germination percentage ≥ 10%, purity ≥ 50%, thousand-grain weight ≥ 08 g, seed moisture ≤ 13%.

  2. Standard Operating Procedures for PET/CT: A Practical Approach for Use in Adult Oncology

    International Nuclear Information System (INIS)

    2013-01-01

    Over the past 20 years, positron emission tomography (PET) and PET/CT (computed tomography) have revolutionized the care of cancer patients in developed countries and are increasingly being adopted in emerging economies. PET has been, and still is, one of the fastest growing fields in medical imaging. There are several reasons for the rapid development of this imaging technology. As the populations of many countries continue to age, cancer constitutes a major health problem, with increasing incidence worldwide. In developed countries where heart disease is the primary cause of mortality, cancer is a close second and may eventually overtake it. Proper cancer management requires highly accurate imaging to characterize, stage, restage, assess response to therapy, prognosticate and detect recurrence. Such information is critical in a disease that often requires the correct initial treatment in order to improve the chance of successfully curing the patient. The ability to provide, in a single imaging session, detailed anatomical and metabolic/functional information, which has a powerful synergistic effect that is greater than the sum of the two individual techniques, has established PET/CT as an indispensable imaging procedure in the management of many different types of cancer. The quality and reliability of the images acquired on a PET/CT scanner depend on the quality of the imaging technique. This publication addresses this important aspect of PET/CT imaging, namely, how to perform an 18F-fluorodeoxyglucose (FDG) PET/CT scan in an adult patient with cancer. Although there are several publications and guidelines on different protocols for PET/CT imaging using FDG, the aim here is to provide a comprehensive overview that can be used both by new PET/CT centres in the process of starting up and by established imaging centres for updating older protocols. Written by experts from several continents, the book provides an up to date, evidence based and comprehensive overview

  3. Compliance determination procedures for environmental radiation protection standards for uranium recovery facilities 40 CFR part 190

    International Nuclear Information System (INIS)

    1982-03-01

    Uranium Milling operations are licensed by the Nuclear Regulatory Commission and by some States in agreement with the Commission. The radiation dose to any individual from the operation of facilities within the uranium fuel cycle is limited to levels set by the Environmental Protection Agency. These levels are contained in the EPA Environmental Radiation Protection Standards for Nuclear Power Operations, in Part 190 of Title 40 of the Code of Federal Regulations (40 CFR Part 190). This report describes the procedures used within NRC's Uranium Recovery Licensing Branch for evaluating compliance with these regulations for uranium milling operations. The report contains descriptions of these procedures, dose factors for evaluating environmental measurement data, and guidance to the NRC staff reviewer

  4. Assessment of organ doses by standard X-ray procedures in the GDR

    International Nuclear Information System (INIS)

    Tautz, M.; Brandt, G.A.

    1986-01-01

    A modern method has been described to assess the radiation burden by X-ray procedures with consideration of the standards of our Society for Medical Radiology in the GDR. The underlying methodology is a Monte Carlo computer technique, which simulates stochastically the energy deposition of X-ray photons in a mathematically described heterogeneous anthropomorphic phantom by Rosenstein (US Department of Health, Education and Welfare). To apply the procedure specific values for the following parameters must be determined for each dose estimation: projection and view, X-ray field size and location entrance exposure at skin surface, beam quality, source-to-image receptor distance. The base data are obtained in terms of tissue-air ratio. Organ doses were calculated for chest, urography, skull, cervical spine, thoracic spine, lumbar spine, pelvis and lymphography. Concluding possibilities have been discussed for reduction of radiation burden. 9 refs., 6 figs., 9 tabs. (author)

  5. Oblique projections and standard-form transformations for discrete inverse problems

    DEFF Research Database (Denmark)

    Hansen, Per Christian

    2013-01-01

    This tutorial paper considers a specific computational tool for the numerical solution of discrete inverse problems, known as the standard-form transformation, by which we can treat general Tikhonov regularization problems efficiently. In the tradition of B. N. Datta's expositions of numerical li...... linear algebra, we use the close relationship between oblique projections, pseudoinverses, and matrix computations to derive a simple geometric motivation and algebraic formulation of the standard-form transformation....

  6. Problems and solutions in application of IEEE standards at Savannah River Site, Department of Energy (DOE) nuclear facilities

    International Nuclear Information System (INIS)

    Lee, Y.S.; Bowers, T.L.; Chopra, B.J.; Thompson, T.T.; Zimmerman, E.W.

    1993-01-01

    The Department of Energy (DOE) Nuclear Material Production Facilities at the Savannah River Site (SRS) were designed, constructed, and placed into operation in the early 1950's, based on existing industry codes/standards, design criteria, analytical procedures. Since that time, DOE has developed Orders and Polices for the planning, design and construction of DOE Nuclear Reactor Facilities which invoke or reference commercial nuclear reactor codes and standards. The application of IEEE reactor design requirements such as Equipment Qualification, Seismic Qualification, Single Failure Criteria, and Separation Requirement, to non-reactor facilities has been a problem since the IEEE reactor criteria do not directly confirm to the needs of non-reactor facilities. SRS Systems Engineering is developing a methodology for the application of IEEE Standards to non-reactor facilities at SRS

  7. The primary exposure standard of ENEA for medium energy X-ray: characteristics and measurements procedures

    International Nuclear Information System (INIS)

    Laitano, R.F.; Toni, M.P.

    1983-01-01

    A description is given of a medium energy X-ray free-air chamber used, as primary exposure standard, at the Laboratorio di Metrologia delle Radiazioni Ionizzanti of the Enea in Italy. The main features of an X-ray facility for the production of radiation between 40 KeV and 400 KeV are also described. The measurements procedures are then analyzed with respect to the realization of the exposure unit in the relevant energy range. Finally the results of some international comparisons are reported

  8. Land acquisition problems in China ' adopting land acquisition act 1960 of Malaysia as an alternative procedure

    Directory of Open Access Journals (Sweden)

    Anuar Alias

    2011-06-01

    Full Text Available Land is scarce and it is the most important resource that humans rely on. Therefore, the protection of land interests is extremely important. Land acquisition deprives the owner's interest on land. A fair and adequate compensation as well as transparent procedures are crucial for land acquisition. The aims of this study are to investigate the adequacy of compensation for land acquisition in China as compared to the Malaysian framework, and to enhance the understanding of land acquisition procedures and determination of compensation in both China and Malaysia. A case study was conducted to investigate whether the compensation for land acquisition in China is adequate and equitable. Two sets of compensation have been calculated, one based on the current compensation standard executed in China; and the other, calculated based on the market value of the land. The finding reveals that the compensation based on the current compensation standard in China is inadequate. The compensation determined by compensation standard executed varied with the market value of the land. In order to better protect the dispossessed owners in China, the compensation for land acquisition should be based on the market value of the land and other related matters such as betterment, severance, injurious affection, incidental expenses and accommodation works should be given due consideration.

  9. New Serbian criminal procedure: New reasons for harmonization with European legal standards

    Directory of Open Access Journals (Sweden)

    Đurđić Vojislav

    2014-01-01

    Full Text Available The new criminal procedure, set forth in 2011, represents a compilation of the inquisitive model of preliminary proceedings, on the one hand, and adversarial trial of the Anglo-American type of criminal procedure on the other. Introduction of the public prosecutor's investigation required a subtle legislative approach to the protection of human rights in criminal proceedings, in order to establish equilibrium between efficient and just procedure. Instead of the expected, the erroneous conception based on the ideas that the public prosecutor's investigation should be strictly formal as that of a court, that evidence taken by the non-judicial authorities should have the same bearing as those taken by the courts, and that the court should have no role in conducting investigation, resulted in an overly inferior position of the accuses compared to that of the public prosecutor. Beside the fact that such conception can not pass the ECJ test, the specific legal solutions referring the investigation open the question of harmonization with the European legal standards. The provisions on initiation of this phase of the proceedings, not being legally sanctioned, put in question the right of the accused to access justice, as well as his right to an effective legal remedy, and the introduced investigation against the unknown perpetrator, the right to be present at one's own trial is being jeopardized. Neither do all procedural rules pertaining to the trial support the fair procedure principle: the indirect extortion of evidence from the defense is discordant with the rule that the burden of proof lies on the prosecutor, as one of the main pillars of the assumption of innocence; as well as the broad opportunity to use non-judicial evidence at the hearing without any major legal obstacles, have demolished the principles of directness and contradictoriness. Even some of the minimal right of the defense as well as the guarantees of personal freedom in the course

  10. The hierarchy problem and the cosmological constant problem in the Standard Model

    International Nuclear Information System (INIS)

    Jegerlehner, Fred

    2015-03-01

    We argue that the SM in the Higgs phase does not suffer form a ''hierarchy problem'' and that similarly the ''cosmological constant problem'' resolves itself if we understand the SM as a low energy effective theory emerging from a cut-off medium at the Planck scale. We discuss these issues under the condition of a stable Higgs vacuum, which allows to extend the SM up to the Planck length. The bare Higgs boson mass then changes sign below the Planck scale, such the the SM in the early universe is in the symmetric phase. The cut-off enhanced Higgs mass term as well as the quartically enhanced cosmological constant term trigger the inflation of the early universe. The coefficients of the shift between bare and renormalized Higgs mass as well as of the shift between bare and renormalized vacuum energy density exhibit close-by zeros at some point below the Planck scale. The zeros are matching points between short distance and the renormalized low energy quantities. Since inflation tunes the total energy density to take the critical value of a flat universe Ω tot =ρ tot /ρ crit =Ω Λ +Ω matter +Ω radiation =1 it is obvious that Ω Λ today is of order Ω tot given that 1>Ω matter , Ω radiation >0, which saturate the total density to about 26 % only, the dominant part being dark matter(21%).

  11. Development of quality standards of medicinal mistletoe – Helicanthes elastica (Desr. Danser employing Pharmacopoeial procedures

    Directory of Open Access Journals (Sweden)

    K.N. Sunil Kumar

    2016-11-01

    Full Text Available Helicanthes elastica (Desr. Danser (Loranthaceae, commonly known as Indian mango mistletoe, is a parasitic shrub found widely growing on mango trees in southern India. Development of monographic quality standards is need of the hour for Pharmacopoeial/extra-Pharmacopoeial and folk medicinal plants. Systematic pharmacognostical evaluation of leaves of H. elastica has been carried out employing Pharmacopoeial procedures of testing herbal drugs. Macro–microscopic features of H. elastica leaf were recorded. Ethanolic extract was tested positive for alkaloids, steroids, carbohydrates, tannins, saponins and phenols. HPTLC fingerprint profile was developed for the identification of extracts using reference standard β-sitosterol glucoside. Results of the present investigation would serve as a source of pharmacognostical information and a document to control the quality of H. elastica (Desr. Danser. Keywords: HPTLC, Mango mistletoe, Medicinal plant monograph, Quality control

  12. From Novice to Expert: Problem Solving in ICD-10-PCS Procedural Coding

    Science.gov (United States)

    Rousse, Justin Thomas

    2013-01-01

    The benefits of converting to ICD-10-CM/PCS have been well documented in recent years. One of the greatest challenges in the conversion, however, is how to train the workforce in the code sets. The International Classification of Diseases, Tenth Revision, Procedure Coding System (ICD-10-PCS) has been described as a language requiring higher-level reasoning skills because of the system's increased granularity. Training and problem-solving strategies required for correct procedural coding are unclear. The objective of this article is to propose that the acquisition of rule-based logic will need to be augmented with self-evaluative and critical thinking. Awareness of how this process works is helpful for established coders as well as for a new generation of coders who will master the complexities of the system. PMID:23861674

  13. Incorporating the Common Core's Problem Solving Standard for Mathematical Practice into an Early Elementary Inclusive Classroom

    Science.gov (United States)

    Fletcher, Nicole

    2014-01-01

    Mathematics curriculum designers and policy decision makers are beginning to recognize the importance of problem solving, even at the earliest stages of mathematics learning. The Common Core includes sense making and perseverance in solving problems in its standards for mathematical practice for students at all grade levels. Incorporating problem…

  14. Problems raised by participation of foreign citizens in national licensing procedures - aspects of public international law

    International Nuclear Information System (INIS)

    Pelzer, N.

    1983-01-01

    In western Europe persons living in border areas increasingly ask for participation in national licensing procedures for nuclear installations to be erected close to the border in neighbouring countries. National practices vary in this matter. Whilst many countries concede rights of participation to foreign citizens in the border areas, the Federal Republic of Germany, e.g., denies foreign citizens direct participation. The paper enquires into the connected problems of public international law and pertinent international treaties and international customary low are examined. (NEA) [fr

  15. A Heuristic Procedure for the Outbound Container Relocation Problem during Export Loading Operations

    Directory of Open Access Journals (Sweden)

    Roberto Guerra-Olivares

    2015-01-01

    Full Text Available During export ship loading operations, it is often necessary to perform relocation movements with containers that interfere with access to the desired container in the ship loading sequence. This paper presents a real-time heuristic procedure for the container relocation problem employing reachstacker vehicles as container handling equipment. The proposed heuristic searches for good relocation coordinates within a set of nearby bays. The heuristic has a parameter that determines how far from the original bay a container may be relocated. The tradeoff between reducing relocation movements and limiting vehicle travel distances is examined and the performance of the heuristic is compared with a common practice in the smaller container terminals in Chile and Mexico. Finally, a mathematical model for the container relocation problem is presented.

  16. The Cox-maze IV procedure in its second decade: still the gold standard?

    Science.gov (United States)

    Ruaengsri, Chawannuch; Schill, Matthew R; Khiabani, Ali J; Schuessler, Richard B; Melby, Spencer J; Damiano, Ralph J

    2018-04-01

    Atrial fibrillation (AF) is the most common cardiac arrhythmia and the treatment options include medical treatment and catheter-based or surgical interventions. AF is a major cause of stroke, and its prevalence is increasing. The surgical treatment of AF has been revolutionized over the past 2 decades through surgical innovation and improvements in endoscopic imaging, ablation technology and surgical instrumentation. The Cox-maze (CM) procedure, which was developed by James Cox and introduced clinically in 1987, is a procedure in which multiple incisions are created in both the left and the right atria to eliminate AF while allowing the sinus impulse to reach the atrioventricular node. This procedure became the gold standard for the surgical treatment of AF. Its latest iteration is termed the CM IV and was introduced in 2002. The CM IV replaced the previous cut-and-sew method (CM III) by replacing most of the incisions with a combination of bipolar radiofrequency and cryoablation. The use of ablation technologies, made the CM IV technically easier, faster and more amenable to minimally invasive approaches. The aims of this article are to review the indications and preoperative planning for the CM IV, to describe the operative technique and to review the literature including comparisons of the CM IV with the previous cut-and-sew method. Finally, this review explores future directions for the surgical treatment of patients with AF.

  17. Standardized uptake values of fluorine-18 fluorodeoxyglucose: the value of different normalization procedures

    International Nuclear Information System (INIS)

    Schomburg, A.; Bender, H.; Reichel, C.; Sommer, T.; Ruhlmann, J.; Kozak, B.; Biersack, H.J.

    1996-01-01

    While the evident advantages of absolute metabolic rate determinations cannot be equalled by static image analysis of fluorine-18 fluorodexyglucose positron emission tomographic (FDG PET) studies, various algorithms for the normalization of static FDG uptake values have been proposed. This study was performed to compare different normalization procedures in terms of dependency on individual patient characteristics. Standardized FDG uptake values (SUVs) were calculated for liver and lung tissue in 126 patients studied with whole-body FDG PET. Uptake values were normalized for total body weight, lean body mass and body surface area. Ranges, means, medians, standard deviations and variation coefficients of these SUV parameters were calculated and their interdependency with total body weight, lean body mass, body surface area, patient height and blood sugar levels was calculated by means of regression analysis. Standardized FDG uptake values normalized for body surface area were clearly superior to SUV parameters normalized for total body weight or lean body mass. Variation and correlation coefficients of body surface area-normalized uptake values were minimal when compared with SUV parameters derived from the other normalization procedures. Normalization for total body weight resulted in uptake values still dependent on body weight and blood sugar levels, while normalization for lean body mass did not eliminate the positive correlation with lean body mass and patient height. It is concluded that normalization of FDG uptake values for body surface area is less dependent on the individual patient characteristics than are FDG uptake values normalized for other parameters, and therefore appears to be preferable for FDG PET studies in oncology. (orig.)

  18. A New Improved Quantum Evolution Algorithm with Local Search Procedure for Capacitated Vehicle Routing Problem

    Directory of Open Access Journals (Sweden)

    Ligang Cui

    2013-01-01

    Full Text Available The capacitated vehicle routing problem (CVRP is the most classical vehicle routing problem (VRP; many solution techniques are proposed to find its better answer. In this paper, a new improved quantum evolution algorithm (IQEA with a mixed local search procedure is proposed for solving CVRPs. First, an IQEA with a double chain quantum chromosome, new quantum rotation schemes, and self-adaptive quantum Not gate is constructed to initialize and generate feasible solutions. Then, to further strengthen IQEA's searching ability, three local search procedures 1-1 exchange, 1-0 exchange, and 2-OPT, are adopted. Experiments on a small case have been conducted to analyze the sensitivity of main parameters and compare the performances of the IQEA with different local search strategies. Together with results from the testing of CVRP benchmarks, the superiorities of the proposed algorithm over the PSO, SR-1, and SR-2 have been demonstrated. At last, a profound analysis of the experimental results is presented and some suggestions on future researches are given.

  19. Primary calibration of TXRF in comparison with the standard droplet procedure

    International Nuclear Information System (INIS)

    Dobler, M.; Reus, U.; Knoth, J.; Schwenke, H.

    2000-01-01

    For the determination of contamination on wafer surfaces with total reflection x-ray fluorescence spectrometry (TXRF) normally external 1 ng Ni droplet standards were used for calibration. This method is based on several assumptions about the properties of the standard droplet which are strongly affected by the preparation of the samples. In this paper a study is resented which compares the external droplet method with a calibration procedure using the fundamental physical background of total reflection x-ray fluorescence spectrometry and the properties of Ni bulk material. The particular features of the two methods will be discussed and the obtained results compared to each other. It is demonstrated in this study that the calibration with Ni bulk material is a primary method which offers several advantages compared to the calibration based on droplet standards. These advantages are unique and enable a more reliable and reproducible quantification of contamination on wafer surfaces. This is caused by the fact that the method is standardless and only based on fundamental parameters and natural constants. It is also demonstrated that effects which could be caused by especial features of the measured samples (particle or film, e.g.) or by the degradation of the calibration sample could be excluded. (author)

  20. Development of a standard operating procedure for mammography equipment used in calibration of ionized chambers

    International Nuclear Information System (INIS)

    Rodrigues, Yklys Santos; Potiens, Maria da Penha Albuquerque

    2011-01-01

    Mammography is one widely used technique in the detection of breast cancer. In order to optimize the results achieving better images with lower dose rates, a quality assurance programme must be applied to the equipment. Some control tests use ionization chambers to measure air kerma and other quantities. These tests can only be reliable if the ionization chambers used on them are correctly calibrated. In the present work, it was developed a standard operating procedure (SOP) for quality control tests in a commercial mammography equipment installed in the Calibration Laboratory (LCI) at IPEN - Brazilian Institute for energy and nuclear research). Seven tests were performed in the equipment: Tube voltage and exposition time accuracy and reproducibility, linearity and reproducibility of Air kerma and Half Value Layer (HVL). Then, it was made a measurement of the air kerma in the mammography equipment, using a reference ionization chamber with traceability to a primary laboratory in Germany (Physikalisch-Technische Bundesanstalt - PTB), that was later compared with the air kerma measured in an industrial irradiator. This industrial X-ray generator was recently used in the implementation of X-radiation Standards beams, mammography level, following the Standard IEC 61267. The HVL values varied from 0.36 (25kV) to 0.41 mmA1 (35kV), and the measured air kerma rates were between 9.78 and 17.97 mGy/min. (author)

  1. A non-standard optimal control problem arising in an economics application

    Directory of Open Access Journals (Sweden)

    Alan Zinober

    2013-04-01

    Full Text Available A recent optimal control problem in the area of economics has mathematical properties that do not fall into the standard optimal control problem formulation. In our problem the state value at the final time the state, y(T = z, is free and unknown, and additionally the Lagrangian integrand in the functional is a piecewise constant function of the unknown value y(T. This is not a standard optimal control problem and cannot be solved using Pontryagin's Minimum Principle with the standard boundary conditions at the final time. In the standard problem a free final state y(T yields a necessary boundary condition p(T = 0, where p(t is the costate. Because the integrand is a function of y(T, the new necessary condition is that y(T should be equal to a certain integral that is a continuous function of y(T. We introduce a continuous approximation of the piecewise constant integrand function by using a hyperbolic tangent approach and solve an example using a C++ shooting algorithm with Newton iteration for solving the Two Point Boundary Value Problem (TPBVP. The minimising free value y(T is calculated in an outer loop iteration using the Golden Section or Brent algorithm. Comparative nonlinear programming (NP discrete-time results are also presented.

  2. Evaluation of a standardized procedure for [corrected] microscopic cell counts [corrected] in body fluids.

    Science.gov (United States)

    Emerson, Jane F; Emerson, Scott S

    2005-01-01

    A standardized urinalysis and manual microscopic cell counting system was evaluated for its potential to reduce intra- and interoperator variability in urine and cerebrospinal fluid (CSF) cell counts. Replicate aliquots of pooled specimens were submitted blindly to technologists who were instructed to use either the Kova system with the disposable Glasstic slide (Hycor Biomedical, Inc., Garden Grove, CA) or the standard operating procedure of the University of California-Irvine (UCI), which uses plain glass slides for urine sediments and hemacytometers for CSF. The Hycor system provides a mechanical means of obtaining a fixed volume of fluid in which to resuspend the sediment, and fixes the volume of specimen to be microscopically examined by using capillary filling of a chamber containing in-plane counting grids. Ninety aliquots of pooled specimens of each type of body fluid were used to assess the inter- and intraoperator reproducibility of the measurements. The variability of replicate Hycor measurements made on a single specimen by the same or different observers was compared with that predicted by a Poisson distribution. The Hycor methods generally resulted in test statistics that were slightly lower than those obtained with the laboratory standard methods, indicating a trend toward decreasing the effects of various sources of variability. For 15 paired aliquots of each body fluid, tests for systematically higher or lower measurements with the Hycor methods were performed using the Wilcoxon signed-rank test. Also examined was the average difference between the Hycor and current laboratory standard measurements, along with a 95% confidence interval (CI) for the true average difference. Without increasing labor or the requirement for attention to detail, the Hycor method provides slightly better interrater comparisons than the current method used at UCI. Copyright 2005 Wiley-Liss, Inc.

  3. Performance testing of HEPA filters: Progress towards a European standard procedure

    Energy Technology Data Exchange (ETDEWEB)

    Dyment, J.

    1997-08-01

    Proposals for a future European testing procedure for {open_quotes}High Efficiency Particulate Air Filters (HEPA and ULPA){close_quotes} are being developed by CEN (Comite Europeen de Normalisation). The new standard will be given the status of national standard in participating countries, conflicting national standards being withdrawn. The standard will comprise 5 parts covering the grouping and classification of HEPA and ULPA filters according to their efficiency, fundamental principles of testing, marking etc (in part 1). Part 2 will cover aerosol production, measurement principles, counting equipment and statistics. Parts 3-5 will cover testing flat sheet media, leak testing of filter elements and the efficiency testing of filter elements respectively. The efficiency test methods allow the use of either homogeneous monodisperse or polydisperse aerosols for the determination of particulate filtration efficiencies as a function of particle size. The particle size at which maximum penetration occurs is first determined in flat sheet media tests; tests on filter elements (constructed using the same filter medium) may be carried out using either a homogeneous monodisperse aerosol of the size at which maximum penetration occurs (MPPS) or a polydisperse aerosol whose median size is close to the MPPS. Tests with monodisperse aerosols may be conducted using condensation nucleus counting equipment; tests using polydisperse test aerosols require the use of optical sizing particle counters. When determining the efficiency of filter elements the downstream aerosol concentrations may be determined from air samples obtained using either an overall method (single point sampling after mixing) or a scan method. The scan method also allows {open_quotes}local{close_quotes} efficiency values to be determined. 1 ref., 1 fig., 1 tab.

  4. Calibration of photon and beta ray sources used in brachytherapy. Guidelines on standardized procedures at Secondary Standards Dosimetry Laboratories

    International Nuclear Information System (INIS)

    2004-03-01

    It has generally been recognized that international harmonization in radiotherapy dosimetry is essential. Consequently, the IAEA has given much effort to this, for example by publishing a number of reports in the Technical Reports Series (TRS) for external beam dosimetry, most notably TRS-277 and more recently TRS-398. Both of these reports describe in detail the steps to be taken for absorbed dose determination in water and they are often referred to as 'dosimetry protocols'. Similar to TRS-277, it is expected that TRS-398 will be adopted or used as a model by a large number of countries as their national protocol. In 1996, the IAEA established a calibration service for low dose rate (LDR) 137 Cs brachytherapy sources, which is the most widely used source for treatment of gynecological cancer. To further enhance harmonization in brachytherapy dosimetry, the IAEA published in 1999 IAEA-TECDOC-1079 entitled 'Calibration of Brachytherapy Sources. Guidelines on Standardized Procedures for the Calibration of Brachytherapy Sources at Secondary Standard Dosimetry Laboratories (SSDLs) and Hospitals'. The report was well received and was distributed in a large number of copies to the members of the IAEA/WHO network of SSDLs and to medical physicists working with brachytherapy. The present report is an update of the aforementioned TECDOC. Whereas TECDOC-1079 described methods for calibrating brachytherapy sources with photon energies at or above those of 192 Ir, the current report has a wider scope in that it deals with standardization of calibration of all the most commonly used brachytherapy sources, including both photon and beta emitting sources. The latter sources have been in use for a few decades already, but their calibration methods have been unclear. Methods are also described for calibrating sources used in the rapidly growing field of cardiovascular angioplasty. In this application, irradiation of the vessel wall is done in an attempt to prevent restenosis after

  5. Solving groundwater flow problems by conjugate-gradient methods and the strongly implicit procedure

    Science.gov (United States)

    Hill, Mary C.

    1990-01-01

    The performance of the preconditioned conjugate-gradient method with three preconditioners is compared with the strongly implicit procedure (SIP) using a scalar computer. The preconditioners considered are the incomplete Cholesky (ICCG) and the modified incomplete Cholesky (MICCG), which require the same computer storage as SIP as programmed for a problem with a symmetric matrix, and a polynomial preconditioner (POLCG), which requires less computer storage than SIP. Although POLCG is usually used on vector computers, it is included here because of its small storage requirements. In this paper, published comparisons of the solvers are evaluated, all four solvers are compared for the first time, and new test cases are presented to provide a more complete basis by which the solvers can be judged for typical groundwater flow problems. Based on nine test cases, the following conclusions are reached: (1) SIP is actually as efficient as ICCG for some of the published, linear, two-dimensional test cases that were reportedly solved much more efficiently by ICCG; (2) SIP is more efficient than other published comparisons would indicate when common convergence criteria are used; and (3) for problems that are three-dimensional, nonlinear, or both, and for which common convergence criteria are used, SIP is often more efficient than ICCG, and is sometimes more efficient than MICCG.

  6. Influence of new customs procedures and logistic security standards on companies competiveness – a Croatian company case study

    Directory of Open Access Journals (Sweden)

    Aleksandar Erceg

    2014-12-01

    Full Text Available In today’s global market, companies are constantly confronted with the competition on the local, national and international level. Companies therefore use a variety of strategies and tools to become and/or remain competitive. Potential areas for cost reduction in companies are supply chain management and logistic and customs procedures. Implementation of various logistic standards in supply chain management can provide significant cost savings for the company’s daily operations and thus reduce overall costs and improve the competitiveness. Using different customs procedures and logistic standards to reduce their costs and become more competitive in the market is necessary for Croatian companies. The method of using these tools is not a one-time process and requires constant efforts. Companies therefore have to be ready to improve daily to be and remain competitive. Using a variety of modern customs procedures can save their money and time, not only through these procedures, but also through better use of their employee’s time, their own vehicles and other equipment. The paper analyzes various customs procedures and logistic standards that can help companies save time and money and improve their competitiveness. In the example of Croatian company, which uses various available procedures and standards the benefits of their use are shown. Apart from bringing savings in operations, all these procedures and standards allow the company to be better, cheaper and more attractive to buyers.

  7. The CIPM list of recommended frequency standard values: guidelines and procedures

    Science.gov (United States)

    Riehle, Fritz; Gill, Patrick; Arias, Felicitas; Robertsson, Lennart

    2018-04-01

    A list of standard reference frequency values (LoF) of quantum transitions from the microwave to the optical regime has been recommended by the International Committee for Weights and Measures (Comité international des poids et mesures, CIPM) for use in basic research, technology, and for the metrology of time, frequency and length. The CIPM LoF contains entries that are recommended as secondary representations of the second in the International System of Units, and entries that can be used to serve as realizations of the definition of the metre. The historical perspective that led to the CIPM LoF is outlined. Procedures have been developed for updating existing, and validating new, entries into the CIPM LoF. The CIPM LoF might serve as an entry for a future redefinition of the second by an optical transition.

  8. Constructing an exposure chart: step by step (based on standard procedures)

    International Nuclear Information System (INIS)

    David, Jocelyn L; Cansino, Percedita T.; Taguibao, Angileo P.

    2000-01-01

    An exposure chart is very important in conducting radiographic inspection of materials. By using an accurate exposure chart, an inspector is able to avoid a trial and error way of determining correct time to expose a specimen, thereby producing a radiograph that has an acceptable density based on a standard. The chart gives the following information: x-ray machine model and brand, distance of the x-ray tube from the film, type and thickness of intensifying screens, film type, radiograph density, and film processing conditions. The methods of preparing an exposure chart are available in existing radiographic testing manuals. These described methods are presented in step by step procedures, covering the actual laboratory set-up, data gathering, computations, and transformation of derived data into Characteristic Curve and Exposure Chart

  9. Standard Operating Procedure (SOP) for Rapid and Efficient Production of Stevia Tissue Culture Seedlings

    International Nuclear Information System (INIS)

    Norazlina Noordin; Peng, C.S.; Rusli Ibrahim

    2015-01-01

    Stevia rebaudiana Bertoni is a non-caloric natural sweetener which is 300 times sweeter than cane sugar. Extracts from stevia leaves has vast application in food and beverages based industries, can be added to tea and coffee, cooked or baked goods, processed foods and confectionary goods. Recently, stevia attained awareness owing to its natural, non-caloric sweetness by diet/ health conscious and diabetic persons (Arpita et al., 2011). This natural sweetener has high commercial value in global market, it was estimated that global market value for stevia is be around USD11 billion by year 2015. Although stevia is being largely popularized in Malaysia and other countries but large-scale propagation procedures for the continuous supply of planting materials in commercial plantation has yet to be established, optimized and standardized. Furthermore, propagation through stevia seeds is often very difficult due to self-incompatibility which results in sterile seeds (Sakaguchi et al., 1982). Tissue culture is the only rapid process for the mass propagation of stevia and there have been few reports of in vitro growth of stevia (Miyagaya et al., 1986) and in vitro micropropagation from shoot tip and leaf (Uddin et al., 2006). Hence, study was carried out to establish a suitable protocol for in vitro propagation of S. rebaudiana Bertoni that can be further up-scaled for mass propagation of stevia seedlings. The established Standard Operating Procedure (SOP) will ensure rapid and efficient production of stevia tissue culture seedlings for continuous supply of planting materials for commercial stevia plantations in Malaysia. Preparation of growth medium, multiplication of shoots, rooting of plant lets and hardening of ex-vitro rooted plant lets is discussed in this paper. (author)

  10. Development of a standardized training course for laparoscopic procedures using Delphi methodology.

    Science.gov (United States)

    Bethlehem, Martijn S; Kramp, Kelvin H; van Det, Marc J; ten Cate Hoedemaker, Henk O; Veeger, Nicolaas J G M; Pierie, Jean Pierre E N

    2014-01-01

    Content, evaluation, and certification of laparoscopic skills and procedure training lack uniformity among different hospitals in The Netherlands. Within the process of developing a new regional laparoscopic training curriculum, a uniform and transferrable curriculum was constructed for a series of laparoscopic procedures. The aim of this study was to determine regional expert consensus regarding the key steps for laparoscopic appendectomy and cholecystectomy using Delphi methodology. Lists of suggested key steps for laparoscopic appendectomy and cholecystectomy were created using surgical textbooks, available guidelines, and local practice. A total of 22 experts, working for teaching hospitals throughout the region, were asked to rate the suggested key steps for both procedures on a Likert scale from 1-5. Consensus was reached with Crohnbach's α ≥ 0.90. Of the 22 experts, 21 completed and returned the survey (95%). Data analysis already showed consensus after the first round of Delphi on the key steps for laparoscopic appendectomy (Crohnbach's α = 0.92) and laparoscopic cholecystectomy (Crohnbach's α = 0.90). After the second round, 15 proposed key steps for laparoscopic appendectomy and 30 proposed key steps for laparoscopic cholecystectomy were rated as important (≥4 by at least 80% of the expert panel). These key steps were used for the further development of the training curriculum. By using the Delphi methodology, regional consensus was reached on the key steps for laparoscopic appendectomy and cholecystectomy. These key steps are going to be used for standardized training and evaluation purposes in a new regional laparoscopic curriculum. Copyright © 2014 Association of Program Directors in Surgery. Published by Elsevier Inc. All rights reserved.

  11. Standardization of solvent extraction procedure for determination of uranium in sea water

    International Nuclear Information System (INIS)

    Maity, Sukanta; Dusane, C.B.; Sahu, S.K.; Pandit, G.G.

    2014-01-01

    Marine ecosystem is becoming polluted by heavy metals and naturally occurring radionuclides due to rapid industrialization and human activities. Many contaminants such as heavy metals and naturally occurring radionuclides though occur at extremely low concentration in sea water, are accumulated by marine organisms and concentrations in their body tissue can be hundreds of times greater than sea water. As human being consume different marine organisms like biota, can lead potential health problem to human being. Uranium is a naturally occurring radioactive element which is important for nuclear technology. However, mineral resources for uranium are limited. Seawater is a major source of uranium. The total estimated quantity of uranium in seawater is around four and a half billion tones. Thus, the oceans have the potential to become the most eco-friendly and long sustainable resource for uranium. A number of countries in the world are in search of techniques to recover uranium from seawater economically. For this purpose and also for the environmental monitoring, the determination of uranium in seawater is very much important. Seawater contains very high concentrations of salts and its uranium content is very low. Accordingly, the separation and preconcentration of uranium is usually involved in the analytical procedures used for the determination of uranium in seawater. In the present study solvent extraction procedure was adopted for the determination of uranium in sea water collected from different locations across Thane Creek area, Mumbai, India

  12. A standard operating procedure for the surgical implantation of transmitters in juvenile salmonids

    Science.gov (United States)

    Liedtke, T.L.; Beeman, J.W.; Gee, L.P.

    2012-01-01

    Biotelemetry is a useful tool to monitor the movements of animals and is widely applied in fisheries research. Radio or acoustic technology can be used, depending on the study design and the environmental conditions in the study area. A broad definition of telemetry also includes the use of Passive Integrated Transponder (PIT) tags, either separately or with a radio or acoustic transmitter. To use telemetry, fish must be equipped with a transmitter. Although there are several attachment procedures available, surgical implantation of transmitters in the abdominal cavity is recognized as the best technique for long-term telemetry studies in general (Stasko and Pincock, 1977; Winter, 1996; Jepsen, 2003), and specifically for juvenile salmonids, Oncorhynchus spp. (Adams and others, 1998a, 1998b; Martinelli and others, 1998; Hall and others, 2009). Studies that use telemetry assume that the processes by which the animals are captured, handled, and tagged, as well as the act of carrying the transmitter, will have minimal effect on their behavior and performance. This assumption, commonly stated as a lack of transmitter effects, must be valid if telemetry studies are to describe accurately the movements and behavior of an entire population of interest, rather than the subset of that population that carries transmitters. This document describes a standard operating procedure (SOP) for surgical implantation of radio or acoustic transmitters in juvenile salmonids. The procedures were developed from a broad base of published information, laboratory experiments, and practical experience in tagging thousands of fish for numerous studies of juvenile salmon movements near Columbia River and Snake River hydroelectric dams. Staff from the Western Fisheries Research Center's Columbia River Research Laboratory (CRRL) frequently have used telemetry studies to evaluate new structures or operations at hydroelectric dams in the Columbia River Basin, and these evaluations typically

  13. Standard Error Computations for Uncertainty Quantification in Inverse Problems: Asymptotic Theory vs. Bootstrapping.

    Science.gov (United States)

    Banks, H T; Holm, Kathleen; Robbins, Danielle

    2010-11-01

    We computationally investigate two approaches for uncertainty quantification in inverse problems for nonlinear parameter dependent dynamical systems. We compare the bootstrapping and asymptotic theory approaches for problems involving data with several noise forms and levels. We consider both constant variance absolute error data and relative error which produces non-constant variance data in our parameter estimation formulations. We compare and contrast parameter estimates, standard errors, confidence intervals, and computational times for both bootstrapping and asymptotic theory methods.

  14. Acucise™ endopyelotomy in a porcine model: procedure standardization and analysis of safety and immediate efficacy

    Directory of Open Access Journals (Sweden)

    Andreoni Cássio

    2004-01-01

    Full Text Available PURPOSE: The study here presented was done to test the technical reliability and immediate efficacy of the Acucise device using a standardized technique. MATERIALS AND METHODS: 56 Acucise procedures were performed in pigs by a single surgeon who used a standardized technique: insert 5F angiographic catheter bilaterally up to the midureter, perform retrograde pyelogram, Amplatz super-stiff guidewire is advanced up to the level of the renal pelvis, angiographic catheters are removed, Acucise catheter balloon is advanced to the ureteropelvic junction (UPJ level, the super-stiff guide-wire is removed and the contrast medium in the renal pelvis is aspirated and replaced with distilled water, activate Acucise at 75 watts of pure cutting current, keep the balloon fully inflated for 10 minutes, perform retrograde ureteropyelogram to document extravasation, remove Acucise catheter and pass an ureteral stent and remove guide-wire. RESULTS: In no case did the Acucise device present malfunction. The electrocautery activation time was 2.2 seconds (ranging from 2 to 4 seconds. The extravasation of contrast medium, visible by fluoroscopy, occurred in 53 of the 56 cases (94.6%. In no case there was any evidence of intraoperative hemorrhage. CONCLUSIONS: This study revealed that performing Acucise endopyelotomy routinely in a standardized manner could largely preclude intraoperative device malfunction and eliminate complications while achieving a successful incision in the UPJ. With the guidelines that were used in this study, we believe that Acucise endopyelotomy can be completed successfully and safely in the majority of selected patients with UPJ obstruction.

  15. The Relationship between Students' Performance on Conventional Standardized Mathematics Assessments and Complex Mathematical Modeling Problems

    Science.gov (United States)

    Kartal, Ozgul; Dunya, Beyza Aksu; Diefes-Dux, Heidi A.; Zawojewski, Judith S.

    2016-01-01

    Critical to many science, technology, engineering, and mathematics (STEM) career paths is mathematical modeling--specifically, the creation and adaptation of mathematical models to solve problems in complex settings. Conventional standardized measures of mathematics achievement are not structured to directly assess this type of mathematical…

  16. Comparison report for CSNI International Standard Problem 12 (ROSA-III Run 912)

    International Nuclear Information System (INIS)

    Tasaka, Kanji; Anoda, Yoshinari; Kumamaru, Hiroshige; Nakamura, Hideo; Iriko, Masanori; Yonomoto, Taisuke; Shiba, Masayoshi

    1982-09-01

    ROSA-III Run 912 was identified as International Standard Problem 12 by the Committee on the Safety of Nuclear Installations. Run 912 simulated a 5% split break LOCA condition in a BWR at the pump suction in the recirculation line with the HPCS failure. Comparisons between the test data and the calculations by eight international participants were made and discussed. (author)

  17. Performance evaluation of different types of particle representation procedures of Particle Swarm Optimization in Job-shop Scheduling Problems

    Science.gov (United States)

    Izah Anuar, Nurul; Saptari, Adi

    2016-02-01

    This paper addresses the types of particle representation (encoding) procedures in a population-based stochastic optimization technique in solving scheduling problems known in the job-shop manufacturing environment. It intends to evaluate and compare the performance of different particle representation procedures in Particle Swarm Optimization (PSO) in the case of solving Job-shop Scheduling Problems (JSP). Particle representation procedures refer to the mapping between the particle position in PSO and the scheduling solution in JSP. It is an important step to be carried out so that each particle in PSO can represent a schedule in JSP. Three procedures such as Operation and Particle Position Sequence (OPPS), random keys representation and random-key encoding scheme are used in this study. These procedures have been tested on FT06 and FT10 benchmark problems available in the OR-Library, where the objective function is to minimize the makespan by the use of MATLAB software. Based on the experimental results, it is discovered that OPPS gives the best performance in solving both benchmark problems. The contribution of this paper is the fact that it demonstrates to the practitioners involved in complex scheduling problems that different particle representation procedures can have significant effects on the performance of PSO in solving JSP.

  18. Standard operation procedures for conducting the on-the-road driving test, and measurement of the standard deviation of lateral position (SDLP).

    Science.gov (United States)

    Verster, Joris C; Roth, Thomas

    2011-01-01

    This review discusses the methodology of the standardized on-the-road driving test and standard operation procedures to conduct the test and analyze the data. The on-the-road driving test has proven to be a sensitive and reliable method to examine driving ability after administration of central nervous system (CNS) drugs. The test is performed on a public highway in normal traffic. Subjects are instructed to drive with a steady lateral position and constant speed. Its primary parameter, the standard deviation of lateral position (SDLP), ie, an index of 'weaving', is a stable measure of driving performance with high test-retest reliability. SDLP differences from placebo are dose-dependent, and do not depend on the subject's baseline driving skills (placebo SDLP). It is important that standard operation procedures are applied to conduct the test and analyze the data in order to allow comparisons between studies from different sites.

  19. Endovascular treatment outcomes using the Stroke Triage Education, Procedure Standardization, and Technology (STEPS-T) program.

    Science.gov (United States)

    Hassan, Ameer E; Sanchez, Christina; Johnson, Angela N

    2018-02-01

    Background "Door to treatment" time affects outcomes of acute ischemic stroke (AIS) patients undergoing endovascular treatment (EVT). However, the correlation between staff education and accessible technology with stroke outcomes has not been demonstrated. Objective The objective of this paper is to demonstrate the five-year impact of the Stroke Triage Education, Procedure Standardization, and Technology (STEPS-T) program on time-to-treat and clinical outcomes. Methods The study analyzed a prospectively maintained database of AIS patients who benefited from EVT through implementation of STEPS-T. Demographics, clinical characteristics, and modified Rankin Score at three months were analyzed. Thrombolysis in Cerebral Infarction (TICI) scale was used to grade pre- and post-procedure angiographic recanalization. Using electronic hemodynamic recording, stepwise workflow times were collected for door time (T D ), entering angiography suite (T A ), groin puncture (T G ), first DSA (T DSA ), microcatheter placement (T M ), and final recanalization (T R ). Median intervention time (T A to T R ) and recanalization time (T G to T R ) were compared through Year 1 to Year 5. Results A total of 230 individuals (age 74 ± 12, between 30 to 95) were enrolled. Median intervention and recanalization times were significantly reduced, from 121 minutes to 52 minutes and from 83 minutes to 36 minutes respectively from Year 1 to Year 5, ( p < 0.001). Across the study period, annual recruitment went up from 12 to 66 patients, and modified Rankin Score between 0 and 2 increased from 36% to 59% ( p = 0.024). Conclusions STEPS-T improved time-to-treat in patients undergoing mechanical thrombectomy for AIS. During the observation period, clinical outcomes significantly improved.

  20. Effects of adding Braun jejunojejunostomy to standard Whipple procedure on reduction of afferent loop syndrome - a randomized clinical trial.

    Science.gov (United States)

    Kakaei, Farzad; Beheshtirouy, Samad; Nejatollahi, Seyed Moahammad Reza; Rashidi, Iqbal; Asvadi, Touraj; Habibzadeh, Afshin; Oliaei-Motlagh, Mohammad

    2015-12-01

    Whipple surgery (pancreaticodeudenectomy) has a high complication rate. We aimed to evaluate whether adding Braun jejunojejunostomy (side-to-side anastomosis of afferent and efferent loops distal to the gastrojejunostomy site) to a standard Whipple procedure would reduce postoperative complications. We conducted a randomized clinical trial comparing patients who underwent standard Whipple surgery (standard group) and patients who underwent standard Whipple surgery with Braun jejunojejunostomy (Braun group). Patients were followed for 1 month after the procedure and postoperative complications were recorded. Our study included 30 patients: 15 in the Braun and 15 in the standard group. In the Braun group, 4 (26.7%) patients experienced 6 complications, whereas in the standard group, 7 (46.7%) patients experienced 11 complications (p = 0.14). Complications in the Braun group were gastrointestinal bleeding and wound infection (n = 1 each) and delayed gastric emptying and pulmonary infection (n = 2 each). Complications in the standard group were death, pancreatic anastomosis leak and biliary anastomosis leak (n = 1 each); gastrointestinal bleeding (n = 2); and afferent loop syndrome and delayed gastric emptying (n = 3 each). There was no significant difference between groups in the subtypes of complications. Our results showed that adding Braun jejunojejunostomy to standard Whipple procedure was associated with lower rates of afferent loop syndrome and delayed gastric emptying. However, more studies are needed to define the role of Braun jejunojejunostomy in this regard. IRCT2014020316473N1 (www.irct.ir).

  1. Qualitative research within trials: developing a standard operating procedure for a clinical trials unit

    Science.gov (United States)

    2013-01-01

    Background Qualitative research methods are increasingly used within clinical trials to address broader research questions than can be addressed by quantitative methods alone. These methods enable health professionals, service users, and other stakeholders to contribute their views and experiences to evaluation of healthcare treatments, interventions, or policies, and influence the design of trials. Qualitative data often contribute information that is better able to reform policy or influence design. Methods Health services researchers, including trialists, clinicians, and qualitative researchers, worked collaboratively to develop a comprehensive portfolio of standard operating procedures (SOPs) for the West Wales Organisation for Rigorous Trials in Health (WWORTH), a clinical trials unit (CTU) at Swansea University, which has recently achieved registration with the UK Clinical Research Collaboration (UKCRC). Although the UKCRC requires a total of 25 SOPs from registered CTUs, WWORTH chose to add an additional qualitative-methods SOP (QM-SOP). Results The qualitative methods SOP (QM-SOP) defines good practice in designing and implementing qualitative components of trials, while allowing flexibility of approach and method. Its basic principles are that: qualitative researchers should be contributors from the start of trials with qualitative potential; the qualitative component should have clear aims; and the main study publication should report on the qualitative component. Conclusions We recommend that CTUs consider developing a QM-SOP to enhance the conduct of quantitative trials by adding qualitative data and analysis. We judge that this improves the value of quantitative trials, and contributes to the future development of multi-method trials. PMID:23433341

  2. Manual of Standard Operating Procedures for Veterinary Drug Residue Analysis (Spanish Edition)

    International Nuclear Information System (INIS)

    2017-01-01

    Laboratories are crucial to national veterinary drug residue monitoring programmes. However, one of the main challenges laboratories encounter is obtaining access to relevant methods of analysis. Thus, in addition to training, providing technical advice and transferring technology, the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture has resolved to develop clear and practical manuals to support Member State laboratories. The Coordinated Research Project (CRP) on Development of Radiometric and Allied Analytical Methods to Strengthen Residue Control Programs for Antibiotic and Anthelmintic Veterinary Drug Residues has developed a number of analytical methods as standard operating procedures (SOPs), which are now compiled here. This publication contains SOPs on chromatographic and spectrometric techniques, as well as radioimmunoassay and associated screening techniques, for various anthelmintic and antimicrobial veterinary drug residue analysis. Some analytical method validation protocols are also included. The publication is primarily aimed at food and environmental safety laboratories involved in testing veterinary drug residues, including under organized national residue monitoring programmes. It is expected to enhance laboratory capacity building and competence through the use of radiometric and complementary tools and techniques. The publication is also relevant for applied research on residues of veterinary drugs in food and environmental samples

  3. Standard measurement procedures for the characterization of fs-laser optical components

    Science.gov (United States)

    Starke, Kai; Ristau, Detlev; Welling, Herbert

    2003-05-01

    Ultra-short pulse laser systems are considered as promising tools in the fields of precise micro-machining and medicine applications. In the course of the development of reliable table top laser systems, a rapid growth of ultra-short pulse applications could be observed during the recent years. The key for improving the performance of high power laser systems is the quality of the optical components concerning spectral characteristics, optical losses and the power handling capability. In the field of ultra-short pulses, standard measurement procedures in quality management have to be validated in respect to effects induced by the extremely high peak power densities. The present work, which is embedded in the EUREKA-project CHOCLAB II, is predominantly concentrated on measuring the multiple-pulse LIDT (ISO 11254-2) in the fs-regime. A measurement facility based on a Ti:Sapphire-CPA system was developed to investigate the damage behavior of optical components. The set-up was supplied with an improved pulse energy detector discriminating the influence of pulse-to-pulse energy fluctuations on the incidence of damage. Aditionally, a laser-calorimetric measurement facility determining the absorption (ISO 11551) utilizing a fs-Ti:Sapphire laser was accomplished. The investigation for different pulse durations between 130 fs and 1 ps revealed a drastic increase of absorption in titania coatings for ultra-short pulses.

  4. Standard operating procedures for quality audits of 60Co external beam radiotherapy facilities

    International Nuclear Information System (INIS)

    Larrinaga Cortina, E.F.; Dominguez Hung, L.; Campa Menendez, R.

    2001-01-01

    The use of radiotherapy implies the necessity of rigorous quality standards in its different components, aimed to provide the best possible treatment and avoid potential patients' risks, that could even cause him death. Projects of technical cooperation developed in Cuba and supported by the International Atomic Energy Agency address the implementation of Programs of Quality Assurance (PGC) in radiotherapy services. The establishment of the National Quality Audit Program (PNAC) is a superior stage. The National Control Center for Medical Devices, as the national regulator entity for the control and supervision of medical devices in the National Health System, is responsible for the making and execution of the PNAC. The audit modality selected was the inspection visit in situ due to its intrinsic advantages, our geographical extension and the number of radiotherapy services. This paper presents the methodology for the execution of the PNAC, in form of a Normalized Procedure of Operation (PNO) that defines the objectives, scope, terms and definitions, responsibilities, composition and selection of the auditor team, security's conditions, materials and equipment, steps of the audit execution, results calculation and interpretation, records, etc. (author)

  5. Manual of Standard Operating Procedures for Veterinary Drug Residue Analysis (French Edition)

    International Nuclear Information System (INIS)

    2017-01-01

    Laboratories are crucial to national veterinary drug residue monitoring programmes. However, one of the main challenges laboratories encounter is obtaining access to relevant methods of analysis. Thus, in addition to training, providing technical advice and transferring technology, the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture has resolved to develop clear and practical manuals to support Member State laboratories. The Coordinated Research Project (CRP) on Development of Radiometric and Allied Analytical Methods to Strengthen Residue Control Programs for Antibiotic and Anthelmintic Veterinary Drug Residues has developed a number of analytical methods as standard operating procedures (SOPs), which are now compiled here. This publication contains SOPs on chromatographic and spectrometric techniques, as well as radioimmunoassay and associated screening techniques, for various anthelmintic and antimicrobial veterinary drug residue analysis. Some analytical method validation protocols are also included. The publication is primarily aimed at food and environmental safety laboratories involved in testing veterinary drug residues, including under organized national residue monitoring programmes. It is expected to enhance laboratory capacity building and competence through the use of radiometric and complementary tools and techniques. The publication is also relevant for applied research on residues of veterinary drugs in food and environmental samples

  6. Evaluasi Penerapan Standard Operating Procedure-Good Agriculture Practice (SOP-GAP pada Usahatani Padi Organik di Kabupaten Bantul

    Directory of Open Access Journals (Sweden)

    Sriyadi Sriyadi

    2016-02-01

    Full Text Available Food security has meaning not only the availability of adequate food, but also providing security for producers and consumers and ensuring environmental sustainability for sustainable production. Organic farming systems are expected to solve the problem for realizing food security and enhancement of people's welfare. The results of research indicated that, (1 The implementation level of Standard Operating Procedure-Good Agriculture Practice (SOP-GAP of Organic Rice Farming in Bantul district was quite high, (2 The implementation level of SOP-GAP of Organic Rice Farming related to the availability of capital, the selling price and the purchase price of inputs (seeds and fertilizers, (3 The level of the farmer's decision related to the implementation level of SOP-GAP of organic rice farming, and (4 development of organic rice farming required availability of sufficient capital. In this regard the government, particularly the agriculture authority and food security agency need to disburse or facilitate capital for farmers in revolving as well as low interest loans.

  7. Pragmatic evaluation of the Toyota Production System (TPS analysis procedure for problem solving with entry-level nurses

    Directory of Open Access Journals (Sweden)

    Lukasz Maciej Mazur

    2008-12-01

    Full Text Available Medication errors occurring in hospitals are a growing national concern. These medication errors and their related costs (or wastes are seen as major factors leading to increased patient safety risks and increased waste in the hospital setting.  This article presents a study in which sixteen entry-level nurses utilized a Toyota Production System (TPS analysis procedure to solve medication delivery problems at one community hospital. The objective of this research was to study and evaluate the TPS analysis procedure for problem solving with entry-level nurses. Personal journals, focus group discussions, and a survey study were used to collect data about entry-level nurses’ perceptions of using the TPS problem solving approach to study medication delivery. A regression analysis was used to identify characteristics that enhance problem solving efforts. In addition, propositions for effective problem solving by entry-level nurses to aid in the reduction of medication errors in healthcare delivery settings are offered.

  8. Error Analysis Of Students Working About Word Problem Of Linear Program With NEA Procedure

    Science.gov (United States)

    Santoso, D. A.; Farid, A.; Ulum, B.

    2017-06-01

    Evaluation and assessment is an important part of learning. In evaluation process of learning, written test is still commonly used. However, the tests usually do not following-up by further evaluation. The process only up to grading stage not to evaluate the process and errors which done by students. Whereas if the student has a pattern error and process error, actions taken can be more focused on the fault and why is that happen. NEA procedure provides a way for educators to evaluate student progress more comprehensively. In this study, students’ mistakes in working on some word problem about linear programming have been analyzed. As a result, mistakes are often made students exist in the modeling phase (transformation) and process skills (process skill) with the overall percentage distribution respectively 20% and 15%. According to the observations, these errors occur most commonly due to lack of precision of students in modeling and in hastiness calculation. Error analysis with students on this matter, it is expected educators can determine or use the right way to solve it in the next lesson.

  9. [Financing problems of capital goods. Part 2: procedure for investment appraisal].

    Science.gov (United States)

    Clausen, C C; Bauer, M; Saleh, A; Picker, O

    2008-07-01

    In part 1 of this series about problems of financing capital goods the multiple and partly diametric economic effects of financing instruments were presented using the leasing procedure as an example. The result indicated that due to the complexity of these effects the choice of a specific financing instrument requires an individual consideration. Therefore, part 2 of the series introduces the method of dynamic capital budgeting which allows the instruments discussed in part 1 to be compared with each other and helps to evaluate their economic benefits. More precisely this paper focuses on a comparative analysis of the most common alternatives, leasing, credit financing and investment financing by the state. In this context, after having identified the total costs of ownership of anesthesia devices, the final asset values of the three financing instruments can be compared with each other using the method of dynamic capital budgeting. In contrast to the prevailing opinion, the results show that from a purely fiscal perspective leasing anesthesia devices is the most expensive alternative. Given the fact that no financial support is available from the state, the option of credit financing turns out to be the most preferable alternative from a relatively limited pool of possibilities. However, it still remains to be answered whether credit financing can defend this position against further, innovative forms of debt financing (e.g., factoring, asset-backed securities, hedge funds, mezzanine capital, etc.).

  10. Improvement of Safety Features in Standard Operation Procedure of Tc-99m Generator

    International Nuclear Information System (INIS)

    Manisah Saedon; Mohd Khairul Hakimi; Shyen, A.K.S.

    2011-01-01

    This paper describes the improvements proposed to the original production procedures for Tc-99m generators. Improvements are intended to add safety and health features for workers into the existing procedures. The difference between the new safe work procedures from the original work procedures; is the concern about the safety and health of employees other than the product safety. One of the suggested safety characteristics is by using the visual aid so that the workers can easily see and read the procedures when they perform their duties, whereas the previous procedures are kept in the manual and difficult to access. The purpose of this paper is to share information about the importance of safety and health features for the workers in the procedures established in addition to provide awareness to all parties involved. (author)

  11. Problems encountered in embodying the principles of ICRP-26 and the revised IAEA safety standards into UK national legislation

    International Nuclear Information System (INIS)

    Beaver, P.F.

    1979-01-01

    This paper describes the United Kingdom procedures and format for safety legislation and goes on to show how the necessary legislation for radiological protection will fit into the general framework. The United Kingdom, as a member of the European Community and EURATOM, is bound to implement the Euratom Directive on radiological protection within the next few years. The latest draft of the Directive takes account of the recommendations of ICRP-26 and further, a recent draft of the revised IAEA Basic Safety Standards is a composite of both the Directive and ICRP-26. Thus, the effect of embodying the principles of the Directive is to embody the principles of ICRP-26 and the Basic Safety Standards. Some of the problems which have been met are described and in particular there is discussion of the problems arising from the incorporation of the three ICRP-26 facets of dose control, namely justification, optimization and limitation, into a legislative package. The UK system of evolving safety legislation now requires considerable participation by all the parties affected (or by their representatives). This paper indicates that the involvement of persons affected, coupled with a legislative package which consists of a hierarchy of (a) regulations; (b) codes of practice; and (c) guidance notes, will result in the fundamental principles of ICRP-26 being incorporated into UK legislation in a totally acceptable way. (author)

  12. Analysis of standard problem six (Semiscale test S-02-6) data

    International Nuclear Information System (INIS)

    Cartmill, C.E.

    1977-08-01

    Test S-02-6 of the Semiscale Mod-1 blowdown heat transfer test series was conducted to supply data for the U.S. Nuclear Regulatory Commission Standard Problem Six. To determine the credibility of the data and thus establish the validity of Standard Problem Six, an analysis of the results of Test S-02-6 was performed and is presented. This analysis consisted of investigations of system hydraulic and core thermal data. The credibility of the system hydraulic data was investigated through comparisons of the data with data and calculations from related sources (Test S-02-4) and, when necessary, through assessment of physical events. The credibility of the core thermal data was based on a thorough analysis of physical events. The results of these investigations substantiate the validity of Test S-02-6 data

  13. Reference Material Properties and Standard Problems to Verify the Fuel Performance Models Ver 1.0

    International Nuclear Information System (INIS)

    Yang, Yong Sik; Kim, Jae Yong; Koo, Yang Hyun

    2010-12-01

    All fuel performance models must be validated by in-pile and out-pile tests. However, the model validation requires much efforts and times to confirm its exactness. In many fields, new performance models and codes are confirmed by code-to-code benchmarking process under simplified standard problem analysis. At present, the DUOS, which is the steady state fuel performance analysis code for dual cooled annular fuel, development project is progressing and new FEM module is developed to analyze the fuel performance during transient period. In addition, the verification process is planning to examine the new models and module's rightness by comparing with commercial finite element analysis such as a ADINA, ABAQUS and ANSYS. This reports contains the result of unification of material properties and establishment of standard problem to verify the newly developed models with commercial FEM code

  14. Solving non-standard packing problems by global optimization and heuristics

    CERN Document Server

    Fasano, Giorgio

    2014-01-01

    This book results from a long-term research effort aimed at tackling complex non-standard packing issues which arise in space engineering. The main research objective is to optimize cargo loading and arrangement, in compliance with a set of stringent rules. Complicated geometrical aspects are also taken into account, in addition to balancing conditions based on attitude control specifications. Chapter 1 introduces the class of non-standard packing problems studied. Chapter 2 gives a detailed explanation of a general model for the orthogonal packing of tetris-like items in a convex domain. A number of additional conditions are looked at in depth, including the prefixed orientation of subsets of items, the presence of unusable holes, separation planes and structural elements, relative distance bounds as well as static and dynamic balancing requirements. The relative feasibility sub-problem which is a special case that does not have an optimization criterion is discussed in Chapter 3. This setting can be exploit...

  15. Two-loop renormalization in the standard model, part II. Renormalization procedures and computational techniques

    Energy Technology Data Exchange (ETDEWEB)

    Actis, S. [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany); Passarino, G. [Torino Univ. (Italy). Dipt. di Fisica Teorica; INFN, Sezione di Torino (Italy)

    2006-12-15

    In part I general aspects of the renormalization of a spontaneously broken gauge theory have been introduced. Here, in part II, two-loop renormalization is introduced and discussed within the context of the minimal Standard Model. Therefore, this paper deals with the transition between bare parameters and fields to renormalized ones. The full list of one- and two-loop counterterms is shown and it is proven that, by a suitable extension of the formalism already introduced at the one-loop level, two-point functions suffice in renormalizing the model. The problem of overlapping ultraviolet divergencies is analyzed and it is shown that all counterterms are local and of polynomial nature. The original program of 't Hooft and Veltman is at work. Finite parts are written in a way that allows for a fast and reliable numerical integration with all collinear logarithms extracted analytically. Finite renormalization, the transition between renormalized parameters and physical (pseudo-)observables, are discussed in part III where numerical results, e.g. for the complex poles of the unstable gauge bosons, are shown. An attempt is made to define the running of the electromagnetic coupling constant at the two-loop level. (orig.)

  16. In search for a gold-standard procedure to count motor neurons in the spinal cord.

    Science.gov (United States)

    Ferrucci, Michela; Lazzeri, Gloria; Flaibani, Marina; Biagioni, Francesca; Cantini, Federica; Madonna, Michele; Bucci, Domenico; Limanaqi, Fiona; Soldani, Paola; Fornai, Francesco

    2018-03-14

    Counting motor neurons within the spinal cord and brainstem represents a seminal step to comprehend the anatomy and physiology of the final common pathway sourcing from the CNS. Motor neuron loss allows to assess the severity of motor neuron disorders while providing a tool to assess disease modifying effects. Counting motor neurons at first implies gold standard identification methods. In fact, motor neurons may occur within mixed nuclei housing a considerable amount of neurons other than motor neurons. In the present review, we analyse various approaches to count motor neurons emphasizing both the benefits and bias of each protocol. A special emphasis is placed on discussing automated stereology. When automated stereology does not take into account site-specificity and does not distinguish between heterogeneous neuronal populations, it may confound data making such a procedure a sort of "guide for the perplex". Thus, if on the one hand automated stereology improves our ability to quantify neuronal populations, it may also hide false positives/negatives in neuronal counts. For instance, classic staining for antigens such as SMI-32, SMN and ChAT, which are routinely considered to be specific for motor neurons, may also occur in other neuronal types of the spinal cord. Even site specificity within Lamina IX may be misleading due to neuronal populations having a size and shape typical of motor neurons. This is the case of spinal border cells, which often surpass the border of Lamina VII and intermingle with motor neurons of Lamina IX. The present article discusses the need to join automated stereology with a dedicated knowledge of each specific neuroanatomical setting.

  17. To the problem of reliability standardization in computer-aided manufacturing at NPP units

    International Nuclear Information System (INIS)

    Yastrebenetskij, M.A.; Shvyryaev, Yu.V.; Spektor, L.I.; Nikonenko, I.V.

    1989-01-01

    The problems of reliability standardization in computer-aided manufacturing of NPP units considering the following approaches: computer-aided manufacturing of NPP units as a part of automated technological complex; computer-aided manufacturing of NPP units as multi-functional system, are analyzed. Selection of the composition of reliability indeces for computer-aided manufacturing of NPP units for each of the approaches considered is substantiated

  18. Lithium isotopic abundances in metal-poor stars: a problem for standard big bang nucleosynthesis?

    International Nuclear Information System (INIS)

    Nissen, P.E.; Asplund, M.; Lambert, D.L.; Primas, F.; Smith, V.V.

    2005-01-01

    Spectral obtained with VLT/UVES suggest the existence of the 6 Li isotope in several metal-poor stars at a level that challenges ideas about its synthesis. The 7 Li abundance is, on the other hand, a factor of three lower than predicted by standard Big Bang nucleosynthesis theory. Both problems may be explained if decaying suppersymmetric particles affect the synthesis of light elements in the Big Bang. (orig.)

  19. Austrian contributions to fuel rod failure models shown at the International Standard Problem ISP-14

    International Nuclear Information System (INIS)

    Sdouz, G.

    1984-04-01

    The computer code BALON-2A was improved to perform the International Standard Problem ISP-14. The main extensions are the implementation of input-options and the development of a model to predict the pressure in the fuel rod gap. With these improvements and some calculations for input values satisfying results have been obtained. This is remarkable because loss of coolant accident analyses are performed usually with larger computer codes. (Author) [de

  20. Comparison report on OECD-CSNI containment standard problem N.1

    International Nuclear Information System (INIS)

    Winkler, W.

    1980-05-01

    The technical purpose of this containment standard problem N.1 was to compare experimental results of history of pressure, temperature, pressure difference and water mass after a steam line rupture within a chain of six subsequent compartments (simplified integral test) with the corresponding results of best-estimate post-test calculations from computer codes for three different time intervals. 11 countries took part in the comparison, using 11 different computer codes and several versions

  1. Piping benchmark problems for the ABB/CE System 80+ Standardized Plant

    International Nuclear Information System (INIS)

    Bezler, P.; DeGrassi, G.; Braverman, J.; Wang, Y.K.

    1994-07-01

    To satisfy the need for verification of the computer programs and modeling techniques that will be used to perform the final piping analyses for the ABB/Combustion Engineering System 80+ Standardized Plant, three benchmark problems were developed. The problems are representative piping systems subjected to representative dynamic loads with solutions developed using the methods being proposed for analysis for the System 80+ standard design. It will be required that the combined license licensees demonstrate that their solution to these problems are in agreement with the benchmark problem set. The first System 80+ piping benchmark is a uniform support motion response spectrum solution for one section of the feedwater piping subjected to safe shutdown seismic loads. The second System 80+ piping benchmark is a time history solution for the feedwater piping subjected to the transient loading induced by a water hammer. The third System 80+ piping benchmark is a time history solution of the pressurizer surge line subjected to the accelerations induced by a main steam line pipe break. The System 80+ reactor is an advanced PWR type

  2. THE PROBLEM OF THE FINALITY OF WORSHIP AND THE STANDARD THOMISTIC ACCOUNT

    Directory of Open Access Journals (Sweden)

    Francisco J. Romero Carrasquillo

    2013-11-01

    Full Text Available This paper is an attempt to introduce the issue of the finality of religious worship into the analytical Thomist tradition. It aims to develop a response, based on an analysis of St. Thomas Aquinas’s texts, to the following questions: What is the end of worship? Why do we worship God? What benefit does God derive from our worship? Alternatively, perhaps, is it not ourselves, rather than God, who are the beneficiaries of our own worship? The paper aims to develop what may be called the ‘Standard Thomistic Account’ as a solution to this problem. In the first part (II, the paper examines the problem of the finality of worship within the context of Classical Theism. Part II presents the current state of the problem in the contemporary secondary literature concerning this issue. In the third part (III, the paper focuses on Cajetan’s version of the Standard Thomistic Account, and shows in which aspects it is in need of more nuance to be able to portray Aquinas’ complete solution. Finally, Part IV proposes a careful and faithful reading of the texts and lays out the foundations for a new and more nuanced solution to the problem.

  3. Preoperative Decision Making for Nephron-Sparing Procedure in the Renal Mass: Time for Using Standard Tools?

    NARCIS (Netherlands)

    Zondervan, Patricia J.; van Lienden, Krijn P.; van Delden, Otto M.; de La Rosette, Jean J. M. C. H.; Laguna, M. Pilar

    2016-01-01

    To determine if the application of using standard tools on tumor complexity and comorbidity indexes may replace the traditional choice of nephron-sparing procedure (NSP) based on clinical maximal tumor diameter (cMTD), age, and comorbidity. Anatomic complexity scores (PADUA and RENAL) and Charlson

  4. A Guide for Developing Standard Operating Job Procedures for the Screening & Grinding Process Wastewater Treatment Facility. SOJP No. 1.

    Science.gov (United States)

    Deal, Gerald A.; Montgomery, James A.

    This guide describes standard operating job procedures for the screening and grinding process of wastewater treatment facilities. The objective of this process is the removal of coarse materials from the raw waste stream for the protection of subsequent equipment and processes. The guide gives step-by-step instructions for safety inspection,…

  5. SURF: Taking Sustainable Remediation from Concept to Standard Operating Procedure (Invited)

    Science.gov (United States)

    Smith, L. M.; Wice, R. B.; Torrens, J.

    2013-12-01

    Over the last decade, many sectors of industrialized society have been rethinking behavior and re-engineering practices to reduce consumption of energy and natural resources. During this time, green and sustainable remediation (GSR) has evolved from conceptual discussions to standard operating procedure for many environmental remediation practitioners. Government agencies and private sector entities have incorporated GSR metrics into their performance criteria and contracting documents. One of the early think tanks for the development of GSR was the Sustainable Remediation Forum (SURF). SURF brings together representatives of government, industry, consultancy, and academia to parse the means and ends of incorporating societal and economic considerations into environmental cleanup projects. Faced with decades-old treatment programs with high energy outputs and no endpoints in sight, a small group of individuals published the institutional knowledge gathered in two years of ad hoc meetings into a 2009 White Paper on sustainable remediation drivers, practices, objectives, and case studies. Since then, SURF has expanded on those introductory topics, publishing its Framework for Integrating Sustainability into Remediation Projects, Guidance for Performing Footprint Analyses and Life-Cycle Assessments for the Remediation Industry, a compendium of metrics, and a call to improve the integration of land remediation and reuse. SURF's research and members have also been instrumental in the development of additional guidance through ASTM International and the Interstate Technology and Regulatory Council. SURF's current efforts focus on water reuse, the international perspective on GSR (continuing the conversations that were the basis of SURF's December 2012 meeting at the National Academy of Sciences in Washington, DC), and ways to capture and evaluate the societal benefits of site remediation. SURF also promotes and supports student chapters at universities across the US

  6. Effect of mobile unidirectional air flow unit on microbial contamination of air in standard urologic procedures.

    Science.gov (United States)

    Ferretti, Stefania; Pasquarella, Cesira; Fornia, Samanta; Saccani, Elisa; Signorelli, Carlo; Vitali, Pietro; Sansebastiano, Giuliano Ezio

    2009-12-01

    Infection is one of the most feared complications of surgery. New instrumentation is being developed to reduce deposition of bacteria. We investigated 45 major surgical procedures (21 radical nephrectomies [RN] and 24 radical retropubic prostatectomies [RRP]) in our urology department during 2007. In about one-half of the interventions, an ultraclean air flow mobile (UAF) unit was used. Bacterial sedimentation was evaluated by nitrocellulose membranes placed on the instrument tray and by settle plates positioned at four points in the operating room. In 27 operations, an additional membrane was located near the incision. Bacterial counts on the nitrocellulose membranes during RN were 230 colony-forming units (cfu)/m(2)/h with the UAF unit and 2,254 cfu/m(2)/h without the unit (p = 0.001). During RRP, the values were 288 cfu/m(2)/h and 3,126 cfu/m(2)/h respectively (p = 0.001). The membrane placed near the incision during RN showed a microbial count of 1,235 cfu/m(2)/h with the UAF unit and 5,093 cfu/m(2)/h without the unit (p = 0.002); during RRP, the values were 1,845 cfu/m(2)/h and 3,790 cfu/m(2)/h, respectively (difference not significant). Bacterial contamination detected by settle plates during RN showed a mean value of 2,273 cfu/m(2)/h when the UAF unit was used and 2,054 cfu/m(2)/h without the unit; during RRP, the values were 2,332 cfu/m(2)/h and 2,629 cfu/m(2)/h with and without the UAF unit, respectively (NS). No statistically significant differences were detected in the clinical data registered in patients operated on under standard conditions and while the UAF unit was functioning. The UAF appears able to reduce microbial contamination at the operating table, reaching a bacterial number obtained in ultraclean operating theatres.

  7. Interim radiological safety standards and evaluation procedures for subseabed high-level waste disposal

    International Nuclear Information System (INIS)

    Klett, R.D.

    1997-06-01

    The Seabed Disposal Project (SDP) was evaluating the technical feasibility of high-level nuclear waste disposal in deep ocean sediments. Working standards were needed for risk assessments, evaluation of alternative designs, sensitivity studies, and conceptual design guidelines. This report completes a three part program to develop radiological standards for the feasibility phase of the SDP. The characteristics of subseabed disposal and how they affect the selection of standards are discussed. General radiological protection standards are reviewed, along with some new methods, and a systematic approach to developing standards is presented. The selected interim radiological standards for the SDP and the reasons for their selection are given. These standards have no legal or regulatory status and will be replaced or modified by regulatory agencies if subseabed disposal is implemented. 56 refs., 29 figs., 15 tabs

  8. Risky procedures by nurses in hospitals: problems and (contemplated) refusals of orders by physicians, and views of physicians and nurses

    NARCIS (Netherlands)

    de Bie, J.; Cuperus-Bosma, J.M.; van der Jagt, M.A.; Gevers, J.K.M.; van der Wal, G.

    2005-01-01

    Occurrence of problems with, refusals of orders and contemplated refusals of orders for risky procedures by nurses in Dutch hospitals and views on the safety of performance was studied using postal questionnaires (600 physicians and 3200 nurses, response 60-71%). Of the respondents, 11-30%

  9. Evaluation of the ISO standard 11063 DNA extraction procedure for assessing soil microbial abundance and community structure.

    Directory of Open Access Journals (Sweden)

    Pierre Plassart

    Full Text Available Soil DNA extraction has become a critical step in describing microbial biodiversity. Historically, ascertaining overarching microbial ecological theories has been hindered as independent studies have used numerous custom and commercial DNA extraction procedures. For that reason, a standardized soil DNA extraction method (ISO-11063 was previously published. However, although this ISO method is suited for molecular tools such as quantitative PCR and community fingerprinting techniques, it has only been optimized for examining soil bacteria. Therefore, the aim of this study was to assess an appropriate soil DNA extraction procedure for examining bacterial, archaeal and fungal diversity in soils of contrasting land-use and physico-chemical properties. Three different procedures were tested: the ISO-11063 standard; a custom procedure (GnS-GII; and a modified ISO procedure (ISOm which includes a different mechanical lysis step (a FastPrep ®-24 lysis step instead of the recommended bead-beating. The efficacy of each method was first assessed by estimating microbial biomass through total DNA quantification. Then, the abundances and community structure of bacteria, archaea and fungi were determined using real-time PCR and terminal restriction fragment length polymorphism approaches. Results showed that DNA yield was improved with the GnS-GII and ISOm procedures, and fungal community patterns were found to be strongly dependent on the extraction method. The main methodological factor responsible for differences between extraction procedure efficiencies was found to be the soil homogenization step. For integrative studies which aim to examine bacteria, archaea and fungi simultaneously, the ISOm procedure results in higher DNA recovery and better represents microbial communities.

  10. Conceptual and Procedural Knowledge Community College Students Use when Solving Science Problems

    Science.gov (United States)

    Eibensteiner, Janice L.

    2012-01-01

    Successful science students have mastered their field of study by being able to apply their learned knowledge and problem solving skills on tests. Problem solving skills must be used to figure out the answer to many classes of questions. What this study is trying to determine is how students solve complex science problems in an academic setting in…

  11. Standard Operating Procedures for Preparing and Handling Sterile Male Tsetse flies for Release

    International Nuclear Information System (INIS)

    Argiles-Herrero, Rafa; Leak, Stephen G.A.

    2016-01-01

    The purpose of this SOP is to describe the procedures involved in preparing tsetse flies reared in a breeding facility for release in the field for the sterile insect technique (SIT) as a component of Area-Wide Insect pest Management (AW-IPM). Following the procedures which are outlined will help to ensure that the released sterile male tsetse flies are of optimal quality.

  12. Standard operating procedure for combustion of 14C - samples with OX-500 biological material oxidizer

    International Nuclear Information System (INIS)

    Nashriyah Mat.

    1995-01-01

    This procedure is for the purpose of safe operation of OX-500 biological material oxidizer. For ease of operation, the operation flow chart (including testing the system and sample combustion) and end of day maintenance flow chart were simplified. The front view, diagrams and switches are duly copied from operating manual. Steps on sample preparation are also included for biotic and a biotic samples. This operating procedure is subjected to future reviews

  13. Study of operating procedures in nuclear power plants: Practices and problems

    International Nuclear Information System (INIS)

    Morgenstern, M.H.; Barnes, V.E.; McGuire, M.V.; Radford, L.R.; Wheeler, W.A.

    1987-02-01

    This report describes the project activities, findings, and recommendations of a project entitled ''Program Plan for Assessing and Upgrading Operating Procedures for Nuclear Power Plants.'' The project was performed by the Pacific Northwest Laboratory and Battelle Human Affairs Research Centers for the Division of Human Factors Technology, Office of Nuclear Reactor Regulation, US Nuclear Regulatory Commission (NRC). The project team analyzed and evaluated samples of normal and abnormal operating procedures from 31 commercial nuclear power plant sites operating in the United States. The project team also visited nine nuclear power plants in the United States to obtain information on the development, use, and control of operating procedures. A peer review group was convened to advise the project team on the conduct of the project and to review and comment on the project report. The report contains findings on the usability of operating procedures and on practices concerning the development, use, an control of operating procedures in nuclear power plants. The report includes recommendations to the NRC on the need to upgrade the quality of operating procedures. The report also discusses an approach to a program plan to assess and upgrade operating procedures

  14. Simulation of International Standard Problem No. 44 'KAEVER' experiments on aerosol behaviour with the CONTAIN code

    International Nuclear Information System (INIS)

    Kljenak, I.

    2001-01-01

    Experiments on aerosol behavior in a vapor-saturated atmosphere, which were performed in the KAEVER experimental facility and proposed for the OECD International Standard Problem No. 44, were simulated with the CONTAIN thermal-hydraulic computer code. The purpose of the work was to assess the capability of the CONTAIN code to model aerosol condensation and deposition in a containment of a light-water-reactor nuclear power plant at severe accident conditions. Results of dry and wet aerosol concentrations are presented and analyzed.(author)

  15. PANDA experiment and International Standard Problem for passive cooling systems for afterheat removal

    International Nuclear Information System (INIS)

    Yadigaroglu, G.; Aksan, N.S.

    1999-01-01

    In the context of OECD/NEA, Paul Scherrer Institut (PSI) is working on an International Standard Problem which is to provide information on the efficiency and use of computer program systems for passive afterheat removal systems. The PANDA test facility of PSI was designed for these investigations. A six-phase PANDA experiment provides a basis for pre-calculation and recalculation of selected phases covering a limited number of system-typical operating states and phenomena. The experiment was specified and carried out in the year under report [de

  16. Hydrogen-migration modeling for the EPRI/HEDL standard problems

    International Nuclear Information System (INIS)

    Travis, J.R.

    1982-01-01

    A numerical technique has been developed for calculating the full three-dimensional time-dependent Navier-Stokes equations with multiple species transport. The method is a modified form of the Implicit Continuous-fluid Eulerian (ICE) technique to solve the governing equations for low Mach number flows where pressure waves and local variations in compression and expansion are not significant. Large density variations, due to thermal and species concentration gradients, are accounted for without the restrictions of the classical Boussinesq approximation. Calculations of the EPRI/HEDL standard problems verify the feasibility of using this finite-difference technique for analyzing hydrogen dispersion within LWR containments

  17. Applications of a mapping procedure to nuclear and nuclear structure problems

    International Nuclear Information System (INIS)

    Catara, F.; Sambataro, M.

    1993-01-01

    A mapping procedure which has applied both for the deriving boson images of fermion operators and for constructing nucleon images of quark operators within the framework of nonrelativistic quark model is illustrated

  18. PROCEDURE FOR ANALYSIS COMPLIANCE WITH QUALITY STANDARDS OFFER OF THE BUFFET RESTAURANT CASONA MELIA SANTIAGO DE CUBA

    Directory of Open Access Journals (Sweden)

    Oscar Parada-Pérez

    2016-01-01

    Full Text Available The company hotel Cuban faces the challenge of the competitiveness and the client’s satisfaction in an environment that demands of actions that they assure the quality. This article has as objective to show the application of a procedure for the evaluation of the standards of quality of the offer in the restaurant buffet La Casona of the Hotel Meliá Santiago de Cuba. The results achieved by the application of the procedure allow to perfect the process of taking of decisions and it contributes to the efficiency of the hotel and the elevation of the quality of the service. 

  19. Licensing procedures and siting problems of nuclear power stations in Japan

    International Nuclear Information System (INIS)

    Saito, Osamu.

    1981-10-01

    This paper describes the legislative and regulatory framework for nuclear power plant licensing in Japan and the different stages in the licensing procedure. The role and responsibilities of the authorities competent for the different types of nuclear facilities (power generation, ship propulsion and research) are also reviewed. The Annexes to the paper contain charts of the administrative structure for nuclear activities, the licensing procedure and nuclear facilities. (NEA) [fr

  20. 24 CFR 200.942 - Supplementary specific procedural requirements under HUD building product standards and...

    Science.gov (United States)

    2010-04-01

    ... Standards, Washington, DC 20234. The standards are also available for inspection at the National Archives... 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr... manufacturer, i.e., brought in the market place from distributors or stores, not from the factory. The...

  1. Using Video to Bridge the Gap Between Problem Behavior and a Delayed Time-out Procedure

    OpenAIRE

    Coppage, Sara; Meindl, James N.

    2017-01-01

    Treatment plans focused on problem behavior often include punishment contingencies to decrease problem behavior. Immediate punishers are typically more effective than delayed punishers, but immediate delivery of a punisher is not always possible. Strategies need to be developed to increase the suppressive effects of delayed punishers. This study demonstrated the effectiveness of a treatment package involving replaying a video recording of problem behavior immediately before delivering a 15 mi...

  2. Methodology and Psychological Knowledge Issues in the Procedural Differentiation Sphere and the Evidence Doctrine: Problems of Theory and Legislation

    Directory of Open Access Journals (Sweden)

    Sergey S. Tsyganenko

    2016-09-01

    Full Text Available The paper is devoted to actual problems of the theory and legislation of the modern criminal trial based on provisions of differentiation of a procedural form. Its basic provisions belong also to questions of evidentiary activity. Characteristics of knowledge on criminal case will claim the psychological knowledge and categories included in the mechanism of legal regulation of criminal procedure activity. Key role is allocated for the principle of freedom of an assessment of proofs. In this case the assessment of proofs is carried out on internal belief. Historically it is connected with institute of jury trial and competitiveness. Both the principle of freedom of assessment of proofs, and many other provisions of the procedural theory and the legislation need interpretation and an explanation with use of modern psychological knowledge. At the same time in modern Russian criminal procedure as well as in foreign types of criminal trial the reduced summary or special procedural jurisdictions are actively applied. It means formation of the differentiated model of criminal legal proceedings at which there is a summary process. Simplification of an order of proof on a criminal case through a wide range of exceptions is characteristic of them that constitutes a theoretical and practical problem. At their decision it is necessary to use a modern arsenal of methodology and the theory, including new achievements in the field of psychological knowledge.

  3. Fundamental challenging problems for developing new nuclear safety standard computer codes

    International Nuclear Information System (INIS)

    Wong, P.K.; Wong, A.E.; Wong, A.

    2005-01-01

    Based on the claims of the US Basic patents number 5,084,232; 5,848,377 and 6,430,516 that can be obtained from typing the Patent Numbers into the Box of the Web site http://164.195.100.11/netahtml/srchnum.htm and their associated published technical papers having been presented and published at International Conferences in the last three years and that all these had been sent into US-NRC by E-mail on March 26, 2003 at 2:46 PM., three fundamental challenging problems for developing new nuclear safety standard computer codes had been presented at the US-NRC RIC2003 Session W4. 2:15-3:15 PM. at the Washington D.C. Capital Hilton Hotel, Presidential Ballroom on April 16, 2003 in front of more than 800 nuclear professionals from many countries worldwide. The objective and scope of this paper is to invite all nuclear professionals to examine and evaluate all the current computer codes being used in their own countries by means of comparison of numerical data from these three specific openly challenging fundamental problems in order to set up a global safety standard for all nuclear power plants in the world. (authors)

  4. Prediction of the semiscale blowdown heat transfer test S-02-8 (NRC Standard Problem Five)

    International Nuclear Information System (INIS)

    Fujita, N.; Irani, A.A.; Mecham, D.C.; Sawtelle, G.R.; Moore, K.V.

    1976-10-01

    Standard Problem Five was the prediction of test S-02-8 in the Semiscale Mod-1 experimental program. The Semiscale System is an electrically heated experiment designed to produce data on system performance typical of PWR thermal-hydraulic behavior. The RELAP4 program used for these analyses is a digital computer program developed to predict the thermal-hydraulic behavior of experimental systems and water-cooled nuclear reactors subjected to postulated transients. The RELAP4 predictions of Standard Problem 5 were in good overall agreement with the measured hydraulic data. Fortunately, sufficient experience has been gained with the semiscale break configuration and the critical flow models in RELAP4 to accurately predict the break flow and, hence the overall system depressurization. Generally, the hydraulic predictions are quite good in regions where homogeneity existed. Where separation effects occurred, predictions are not as good, and the data oscillations and error bands are larger. A large discrepancy existed among the measured heater rod temperature data as well as between these data and predicted values. Several potential causes for these differences were considered, and several post test analyses were performed in order to evaluate the discrepancies

  5. Solving the flavour problem in supersymmetric Standard Models with three Higgs families

    International Nuclear Information System (INIS)

    Howl, R.; King, S.F.

    2010-01-01

    We show how a non-Abelian family symmetry Δ 27 can be used to solve the flavour problem of supersymmetric Standard Models containing three Higgs families such as the Exceptional Supersymmetric Standard Model (E 6 SSM). The three 27-dimensional families of the E 6 SSM, including the three families of Higgs fields, transform in a triplet representation of the Δ 27 family symmetry, allowing the family symmetry to commute with a possible high energy E 6 symmetry. The Δ 27 family symmetry here provides a high energy understanding of the Z 2 H symmetry of the E 6 SSM, which solves the flavour changing neutral current problem of the three families of Higgs fields. The main phenomenological predictions of the model are tri-bi-maximal mixing for leptons, two almost degenerate LSPs and two almost degenerate families of colour triplet D-fermions, providing a clear prediction for the LHC. In addition the model predicts PGBs with masses below the TeV scale, and possibly much lighter, which appears to be a quite general and robust prediction of all models based on the D-term vacuum alignment mechanism.

  6. A review on test procedure, energy efficiency standards and energy labels for room air conditioners and refrigerator-freezers

    Energy Technology Data Exchange (ETDEWEB)

    Mahlia, T.M.I.; Saidur, R. [Department of Mechanical Engineering, University of Malaya, 50603 Kuala Lumpur (Malaysia)

    2010-09-15

    Air conditioners and refrigerator-freezers are major energy users in a household environment and hence efficiency improvement of these appliances can be considered as an important step to reduce their energy consumption along with environmental pollution prevention. Energy efficiency standards and labels are commonly used tools to reduce the energy uses for household appliances for many countries around the world. The first step towards adopting energy efficiency standards is to establish a test procedure for rating and testing of an appliance. It may be mentioned that an energy test procedure is the technical foundation for energy efficiency standards, energy labels, and other related programs. This paper reviews requirements and specifications of various international test standards for testing and rating of room air conditioners and refrigerators. A review on the development of the energy efficiency standards has been provided as well. Finally, energy labels that provide some useful information for identifying energy efficient products have been reviewed for these appliances. It may be stated that the review will be useful for the developing countries who wish to develop these energy savings strategies. It is also expected to be useful to revise the existing strategies for a few selected countries who already implemented these strategies earlier. (author)

  7. Extended device profiles and testing procedures for the approval process of integrated medical devices using the IEEE 11073 communication standard.

    Science.gov (United States)

    Janß, Armin; Thorn, Johannes; Schmitz, Malte; Mildner, Alexander; Dell'Anna-Pudlik, Jasmin; Leucker, Martin; Radermacher, Klaus

    2018-02-23

    Nowadays, only closed and proprietary integrated operating room systems (IORS) from big manufacturers are available on the market. Hence, the interconnection of components from third-party vendors is only possible with increased time and costs. In the context of the German Federal Ministry of Education and Research (BMBF)-funded project OR.NET (2012-2016), the open integration of medical devices from different manufacturers was addressed. An integrated operating theater based on the open communication standard IEEE 11073 shall give clinical operators the opportunity to choose medical devices independently of the manufacturer. This approach would be advantageous especially for hospital operators and small- and medium-sized enterprises (SME) of medical devices. Actual standards and concepts regarding technical feasibility and the approval process do not cope with the requirements for a modular integration of medical devices in the operating room (OR), based on an open communication standard. Therefore, innovative approval strategies and corresponding certification and test procedures, which cover actual legal and normative standards, have to be developed in order to support the future risk management and the usability engineering process of open integrated medical devices in the OR. The use of standardized device and service profiles and a three-step testing procedure, including conformity, interoperability and integration tests are described in this paper and shall support the manufacturers to integrate their medical devices without disclosing the medical devices' risk analysis and related confidential expertise or proprietary information.

  8. Dataset and standard operating procedure for newborn screening of six lysosomal storage diseases: By tandem mass spectrometry

    Directory of Open Access Journals (Sweden)

    Susan Elliott

    2016-09-01

    Full Text Available In this data article we provide a detailed standard operating procedure for performing a tandem mass spectrometry, multiplex assay of 6 lysosomal enzymes for newborn screening of the lysosomal storage diseases Mucopolysaccharidosis-I, Pompe, Fabry, Niemann-Pick-A/B, Gaucher, and Krabbe, (Elliott, et al., 2016 [1]. We also provide the mass spectrometry peak areas for the product and internal standard ions typically observed with a dried blood spot punch from a random newborn, and we provide the daily variation of the daily mean activities for all 6 enzymes.

  9. Fostering Modeling Competencies: Benefits of Worked Examples, Problems to Be Solved, and Fading Procedures

    Science.gov (United States)

    Große, Cornelia S.

    2015-01-01

    The application of mathematics to real-world problems is moving more and more in the focus of attention of mathematics education; however, many learners experience huge difficulties in relating "pure" mathematics to everyday contents. In order to solve "modeling problems", it is first necessary to find a transition from a…

  10. Treatment of Multiply Controlled Problem Behavior with Procedural Variations of Differential Reinforcement

    Science.gov (United States)

    Neidert, Pamela L.; Iwata, Brian A.; Dozier, Claudia L.

    2005-01-01

    We describe the assessment and treatment of 2 children with autism spectrum disorder whose problem behaviors (self-injury, aggression, and disruption) were multiply controlled. Results of functional analyses indicated that the children's problem behaviors were maintained by both positive reinforcement (attention) and negative reinforcement (escape…

  11. Bayes procedures for adaptive inference in inverse problems for the white noise model

    NARCIS (Netherlands)

    Knapik, B.T.; Szabó, B.T.; van der Vaart, A.W.; van Zanten, J.H.

    2016-01-01

    We study empirical and hierarchical Bayes approaches to the problem of estimating an infinite-dimensional parameter in mildly ill-posed inverse problems. We consider a class of prior distributions indexed by a hyperparameter that quantifies regularity. We prove that both methods we consider succeed

  12. 47 CFR 22.150 - Standard pre-filing technical coordination procedure.

    Science.gov (United States)

    2010-10-01

    ... this procedure for specific channels and types of stations are contained in the subparts governing the..., emission type and polarization. (4) Transmitting antenna pattern and maximum gain. (5) Transmitting antenna..., even if no channel usage conflicts are anticipated. If any notified party fails to respond within 30...

  13. 46 CFR 164.019-7 - Non-standard components; acceptance criteria and procedures.

    Science.gov (United States)

    2010-10-01

    ... must include a description of the quality control procedures that will be in effect during production... oversight of the manufacturer's program of production quality control, including a description of the... the case of textiles. (5) The request must include a list of all materials used in the construction of...

  14. CTEPP STANDARD OPERATING PROCEDURE FOR CONDUCTING INTERNAL FIELD AUDITS AND QUALITY CONTROL (SOP-2.25)

    Science.gov (United States)

    This SOP describes the method for conducting internal field audits and quality control procedures. Internal field audits will be conducted to ensure the collection of high quality data. Internal field audits will be conducted by Field Auditors (the Field QA Officer and the Field...

  15. 46 CFR 160.055-9 - Procedure for approval-standard and nonstandard life preservers.

    Science.gov (United States)

    2010-10-01

    ... design shall follow the procedures of subpart 159.005 of this chapter, as explained in § 160.001-3 of... manufacturer by the Coast Guard for a nonstandard life preserver approved after tests. (d) Private brand labels. Private brand labels are those bearing the name and address of a distributor in lieu of the manufacturer...

  16. 12 CFR 616.6300 - Leasing policies, procedures, and underwriting standards.

    Science.gov (United States)

    2010-01-01

    ... property and associated risks; (e) Property tax and sales tax reporting; (f) Title and ownership of leased... engaged in lease underwriting must adopt a written policy (or policies). Management, at the direction of the board, must develop procedures that reflect lease practices that control risk and comply with all...

  17. Effects of Computer-Based Training on Procedural Modifications to Standard Functional Analyses

    Science.gov (United States)

    Schnell, Lauren K.; Sidener, Tina M.; DeBar, Ruth M.; Vladescu, Jason C.; Kahng, SungWoo

    2018-01-01

    Few studies have evaluated methods for training decision-making when functional analysis data are undifferentiated. The current study evaluated computer-based training to teach 20 graduate students to arrange functional analysis conditions, analyze functional analysis data, and implement procedural modifications. Participants were exposed to…

  18. 75 FR 34064 - Manufactured Home Construction and Safety Standards, Test Procedures for Roof Trusses

    Science.gov (United States)

    2010-06-16

    ... failure. Failure is rupture, fracture, or excessive yielding. (v) Final recovery phase. Remove 2.0 times... members of the public. Commenters should follow the instructions provided on that site to submit comments... nondestructive testing procedure for roof trusses that permits a lower overall factor of safety to be used in...

  19. Development and testing of standardized procedures and reference data for LWR surveillance

    International Nuclear Information System (INIS)

    McElroy, W.N.

    1979-02-01

    The resources and talents of many national and international organizations and laboratories, both governmental and industrial, are being used to establish analysis methods for predicting the embrittlement condition of light water reactor (LWR) primary systems. The exact interrelationships and responsibilities between those developing, understanding, combining, and applying state-of-the-art technology in dosimetry, metallurgy, and fracture mechanics for reactor systems analysis are being carefully reviewed and studied. This has resulted in a more comprehensive definition of the scope of new and updated ASTM standards required for the analysis and interpretation of LWR pressure vessel surveillance results. Fifteen new and updated ASTM standards have now been identified, together with a restructuring of the main interfaces between the individual standard practices, guides, and methods. The paper briefly discusses these standards and the initial results of multi-laboratory research work involved in their validation and calibration

  20. Multimode Preemptive Resource Investment Problem Subject to Due Dates for Activities: Formulation and Solution Procedure

    Directory of Open Access Journals (Sweden)

    Behrouz Afshar-Nadjafi

    2014-01-01

    Full Text Available The preemptive Multimode resource investment problem is investigated. The Objective is to minimize the total renewable/nonrenewable resource costs and earliness-tardiness costs by a given project deadline and due dates for activities. In this problem setting preemption is allowed with no setup cost or time. The project contains activities interrelated by finish-start type precedence relations with a time lag of zero, which require a set of renewable and nonrenewable resources. The problem formed in this way is an NP-hard. A mixed integer programming formulation is proposed for the problem and parameters tuned genetic algorithm (GA is proposed to solve it. To evaluate the performance of the proposed algorithm, 120 test problems are used. Comparative statistical results reveal that the proposed GA is efficient and effective in terms of the objective function and computational times.

  1. Consultative Committee for Space Data Systems recommendation for space data system standards: Telecommand. Part 2.1: Command operation procedures

    Science.gov (United States)

    1991-01-01

    This recommendation contains the detailed specification of the logic required to carry out the Command Operations Procedures of the Transfer Layer. The Recommendation for Telecommand--Part 2, Data Routing Service contains the standard data structures and data communication procedures used by the intermediate telecommand system layers (the Transfer and Segmentation Layers). In particular, it contains a brief description of the Command Operations Procedures (COP) within the Transfer Layer. This recommendation contains the detailed definition of the COP's in the form of state tables, along with definitions of the terms used. It is assumed that the reader of this document is familiar with the data structures and terminology of part 2. In case of conflict between the description of the COP's in part 2 and in this recommendation, the definition in this recommendation will take precedence. In particular, this document supersedes section 4.3.3.1 through 4.3.3.4 of part 2.

  2. Influence of new customs procedures and logistic security standards on companies competiveness – a Croatian company case study

    OpenAIRE

    Erceg, Aleksandar

    2014-01-01

    In today’s global market, companies are constantly confronted with the competition on the local, national and international level. Companies therefore use a variety of strategies and tools to become and/or remain competitive. Potential areas for cost reduction in companies are supply chain management and logistic and customs procedures. Implementation of various logistic standards in supply chain management can provide significant cost savings for the company’s daily operations an...

  3. Sexual Desire and Hypoactive Sexual Desire Disorder in Women. Introduction and Overview. Standard Operating Procedure (SOP Part 1)

    DEFF Research Database (Denmark)

    Bitzer, Johannes; Giraldi, Annamaria; Pfaus, Jim

    2013-01-01

    Introduction.  Hypoactive sexual desire disorder (HSDD) is defined in Diagnostic and Statistical Manual of Mental Disorders Fourth Edition as persistent or recurrent deficiency (or absence) of sexual fantasies/thoughts, and/or desire for or receptivity to sexual activity, which causes personal...... must be based on a biopsychosocial, multidimensional, and integrative perspective. Bitzer J, Giraldi A, and Pfaus J. Sexual desire and hypoactive sexual desire disorder in women. Introduction and overview. Standard operating procedure (SOP part 1). J Sex Med **;**:**-**....

  4. 77 FR 65823 - Control of Air Pollution From Aircraft and Aircraft Engines; Emission Standards and Test Procedures

    Science.gov (United States)

    2012-10-31

    ... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Parts 87 [EPA-HQ-OAR-2010-0687; FRL-9678-1] RIN 2060-AO70 Control of Air Pollution From Aircraft and Aircraft Engines; Emission Standards and Test Procedures Correction In rule document 2012-13828 appearing on pages 36341-36386 in the issue of Monday, June 18, 2012, make the following corrections: Sec. 87.2...

  5. Procedural law problems with the construction of installations (plants) for the final storage of radioactive materials

    International Nuclear Information System (INIS)

    Hoppe, W.; Bunse, B.

    1984-01-01

    The underground exploration of the salt-mine Gorleben has to be permitted according to sec. 126 para. 3, 51 et seq. Federal Mining Act. There is, however, no need for carrying out a nuclear law procedure for the official approval of the plan because the construction of the exploration mine does not represent the construction of a final storage facility. The operation of exploration measures does not create legally relevant prejudices for procedures of the official approval of the plan according to Atomic Energy Law. (HP) [de

  6. Using Video to Bridge the Gap Between Problem Behavior and a Delayed Time-out Procedure.

    Science.gov (United States)

    Coppage, Sara; Meindl, James N

    2017-09-01

    Treatment plans focused on problem behavior often include punishment contingencies to decrease problem behavior. Immediate punishers are typically more effective than delayed punishers, but immediate delivery of a punisher is not always possible. Strategies need to be developed to increase the suppressive effects of delayed punishers. This study demonstrated the effectiveness of a treatment package involving replaying a video recording of problem behavior immediately before delivering a 15 min delayed time-out. This treatment package may prove to be an accessible and inexpensive strategy when using delayed punishers.

  7. Problemes de l'enseignement des langues secondes standard pour les minorites culturelles (Problems of Teaching Standard Second Languages to Cultural Minorities).

    Science.gov (United States)

    Laforge, Lorne

    In most industrialized countries, especially in urban areas with a heavy concentration of cultural minorities, teaching a standard second language to schoolchildren is a misleading concept and an ambiguous enterprise. In a country that fosters official unilingualism, schoolchildren have to learn a standard second language as if it were a first…

  8. Systemic-institutional approach to solving the problems of prejudgement in the criminal court procedure

    Directory of Open Access Journals (Sweden)

    Bulat Raisovich Burganov

    2015-09-01

    Full Text Available Objective to consider the historical and legal aspects of the use of prejudgement in the criminal procedure and to allocate its characteristic features as of a systemic object to disclose the key system elements of the mechanism of legal regulation of prejudgement in the criminal procedure. Methods the basis of the research was historicallegal method and systemicinstitutional approach to the analysis of regulatory processes as well as special and private law research methods elements of structuralfunctional approach with formal logical analysis. Results the evolution is shown of formation and development of the prejudgement institution the necessity is grounded of systemicholistic analysis of prejudgement legal regulation in the criminal procedure. According to the author it is a systematic approach that will allow to create the effectively functioning prejudgement institution. The article investigates the content side of the prejudgement institution in the criminalprocedural law. Scientific novelty for the first time the article discusses the prejudgement institution as a system of interrelated elements. In this context the substantial side of this system is characterized. Practical significance the research results and conclusions can be used in research legislative and applied activity for the effective application of the principles of prejudgement opportunities in the criminal procedure. nbsp

  9. Towards a new procedure for identifying causes of health and comfort problems in office buildings

    NARCIS (Netherlands)

    Bluyssen, P.M.; Fossati, S.; Mandin, C.; Cattaneo, A.; Carrer, P.

    2012-01-01

    In the European project OFFICAIR a procedure has been prepared for the inventory and identification of associations between possible characteristics of European modern offices (building, sources and events) and health and comfort of office workers, via a questionnaire and a checklist including

  10. Problems involved in quantitative gamma camera scintigraphy. A. Procedure and definitions

    International Nuclear Information System (INIS)

    Erbsmann, F.

    1976-01-01

    In the procedure used the elementary notions on calibration sources (isotropic point source, parallel-beam point source, tubular line source, parallel-ray line source, sources of finite dimensions, homogeneous phantom) are reviewed, together with the most frequently used definitions, those of the scattering function and of the modulation transfer functions [fr

  11. 241-SY-101 DACS instrument problem screen (SCR 448) acceptance test procedure

    International Nuclear Information System (INIS)

    ERMI, A.M.

    1999-01-01

    The operability of the 241-SY-101 Data Acquisition and Control System (DACS) to provide proper control and monitoring of the mitigation mixer pump and instrumentation installed in the 241-SY-101 underground storage tank utilizing the [INSTPROB] screen will be systematically evaluated by the performance of this procedure

  12. Is mammary reconstruction with the anatomical Becker expander a simple procedure? Complications and hidden problems leading to secondary surgical procedures: a follow-up study.

    Science.gov (United States)

    Farace, Francesco; Faenza, Mario; Bulla, Antonio; Rubino, Corrado; Campus, Gian Vittorio

    2013-06-01

    Debate over the role of Becker expander implants (BEIs) in breast reconstruction is still ongoing. There are no clear indications for BEI use. The main indications for BEI use are one-stage breast reconstruction procedure and congenital breast deformities correction, due to the postoperative ability to vary BEI volume. Recent studies showed that BEIs were removed 5 years after mammary reconstruction in 68% of operated patients. This entails a further surgical procedure. BEIs should not, therefore, be regarded as one-stage prostheses. We performed a case-series study of breast reconstructions with anatomically shaped Becker-35™ implants, in order to highlight complications and to flag unseen problems, which might entail a second surgical procedure. A total of 229 patients, reconstructed from 2005 to 2010, were enrolled in this study. Data relating to implant type, volume, mean operative time and complications were recorded. All the patients underwent the same surgical procedure. The minimum follow-up period was 18 months. During a 5-year follow-up, 99 patients required secondary surgery to correct their complications or sequelae; 46 of them underwent BEI removal within 2 years of implantation, 56 within 3 years, 65 within 4 years and 74 within 5 years. Our findings show that two different sorts of complications can arise with these devices, leading to premature implant removal, one common to any breast implant and one peculiar to BEIs. The Becker implant is a permanent expander. Surgeons must, therefore, be aware that, once positioned, the Becker expander cannot be adjusted at a later date, as in two-stage expander/prosthesis reconstructions for instance. Surgeons must have a clear understanding of possible BEI complications in order to be able to discuss these with their patients. Therefore, only surgeons experienced in breast reconstruction should use BEIs. Copyright © 2013 British Association of Plastic, Reconstructive and Aesthetic Surgeons. Published by

  13. International Standard Problem 40 - Aerosol Deposition and Resuspension. Final Comparison Report

    International Nuclear Information System (INIS)

    De Los Reyes, Alfredo Castelo; Areia Capitao, Joaquim; De Santi, Giovanni

    1999-02-01

    The Committee on the Safety of Nuclear Installations of the OECD/NEA, in its meeting of November 1996, endorsed the adoption, as International Standard Problem number 40 (ISP-40), of an experiment on aerosol deposition and resuspension to be run in the STORM facility of the Joint Research Centre of the European Commission (JRC). The problem was run as two consecutive blind exercises. A preparatory workshop took place at the JRC in March 1997 [ 53 ] and approved the test specifications, the experimental data to be supplied to the ISP participants and the results to be submitted to them. It was also decided that the CPU times needed for the different calculations should not be compared in absolute terms but 'normalised' by the CPU time needed for the same computers to run a reference number-crunching code, linpackd, supplied by GRS and already used for another International Standard Problem. The test, STORM test SR11, took place in April 1997 and included two distinct phases, the first concentrating on aerosol deposition mostly by thermophoresis and eddy impaction and the second on aerosol resuspension under a stepwise increasing gas flow. The International Standard Problem was also divided into two phases, each one concerning one of the phases of the experiment. Each organisation could participate in only one or both phases of the exercise. The decision whether or not to model resuspension also during the deposition phase of the exercise was left to the participants. The experimental data for the deposition phase of the exercise - thermal-hydraulics and aerosol feed rate and physical characteristics at the inlet of the test section - were distributed in mid-June 1997 and the deadline for submission of the results for the deposition phase was the end of September 1997. The experimental data for the resuspension phase - thermal-hydraulics, initial deposited mass and size distribution of the resuspended particles - was distributed to the participants in mid

  14. Operationalizing Principle-Based Standards for Animal Welfare-Indicators for Climate Problems in Pig Houses.

    Science.gov (United States)

    Vermeer, Herman M; Hopster, Hans

    2018-03-23

    The Dutch animal welfare law includes so-called principle-based standards. This means that the objective is described in abstract terms, enabling farmers to comply with the law in their own way. Principle-based standards are, however, difficult for the inspection agency to enforce because strict limits are missing. This pilot project aimed at developing indicators (measurements) to assess the climate in pig houses, thus enabling the enforcement of principle-based standards. In total, 64 farms with weaners and 32 farms with growing-finishing pigs were visited. On each farm, a set of climate-related measurements was collected in six pens. For each of these measurements, a threshold value was set, and exceeding this threshold indicated a welfare risk. Farm inspections were carried out during winter and spring, thus excluding situations with heat stress. Assessment of the variation and correlation between measurements reduced the dataset from 39 to 12 measurements. Using a principal components analysis helped to select five major measurements as warning signals. The number of exceeded thresholds per pen and per farm was calculated for both the large (12) and small (five) sets of measurements. CO₂ and NH₃ concentrations were related to the outside temperature. On colder days, there was less ventilation, and thus CO₂ and NH₃ concentrations increased. Air quality, reflected in the CO₂ and NH₃ concentrations, was associated with respiratory problems. Eye scores were positively correlated with both pig and pen fouling, and pig and pen fouling were closely related. We selected five signal indicators: CO₂, NH₃, and tail and eye score for weaners and finishers, and added ear score for weaners and pig fouling for growing-finishing pigs. The results indicate that pig farms can be ranked based on five signal indicators related to reduced animal welfare caused by climatic conditions. This approach could be adopted to other principle-based standards for pigs as well

  15. Proposal evaluation tool of standards and procedures for breast cancer in the province of Cienfuegos

    International Nuclear Information System (INIS)

    Fraga Suarez, Omayda; Sabates Llerandi, Teresita; Arnot Silvera, Rogelio; Torres Aja, Lidia

    2009-01-01

    Breast cancer is one of the most frequent malignancies Although Cuba and be a program with rules and procedures established a high number of women will die from cause. Objectives, design an instrument to assess compliance with the rules and procedures of breast cancer in Cienfuegos Province. Methodological design, a study was conducted descriptive, during the time period from January 2007 to January 2008, whose study group consisted of 55 women diagnosed with breast cancer at the 'Hospital Universitario Dr. Gustavo Lima Aldereguia' of Cienfuegos, the research was divided into three stages: general characterization, design of an assessment tool, criterion validation by external evaluators. Methods were used theoretical, empirical and mathematical statistics. Results, the stadiums most representative were II and III, there are delays in the performance definitive surgery, radical surgical treatments prevail, delays in the initiation of chemotherapy. Findings, there difficulties in adherence and compliance and therapeutic procedures established in the province of Cienfuegos, by which an instrument was designed for evaluation. (Author)

  16. The advantages of using standardized review procedures in certifying type B radioactive material packages

    International Nuclear Information System (INIS)

    Easton, E.P.; Faille, S.

    2004-01-01

    This paper presents the advantages of adopting well-documented standardized review practices for reviewing Type B package designs. The US experience using standardized review plans and guidance has shown them to be a valuable tool in achieving more consistent and efficient package reviews, in training and qualifying technical reviewers, and in enhancing public and industry understanding of the package certification process. In addition, the standardized review practices, as living documents, have proven to be an effective method of incorporating new technical advances into the review process, and have provided a vehicle to make that knowledge widely available to fellow reviewers, the public and industry. Canada implemented a new internal review process in early 2003 to standardize the review of applications for certification of Type B Packages. Based on the similarity of these approaches, the United States and Canada have started discussions on a A North American System for the unilateral approval of Type B (U) packages. This initiative is looking into how each country is currently reviewing transportation package applications to see if agreement can be reached on accepting Type B certifications on a reciprocal basis, i.e., without additional review. Based on the experience in Canada and the United States, the authors believe that the use of standardized review processes, coupled with the knowledge and experience resident in IAEA's Transportation Advisory Material (TS-G-1.1) and series of TECDOCS, could also be used to develop a standard internationally accepted review process that could enhance the acceptance of unilateral approvals for Type B packages

  17. The advantages of using standardized review procedures in certifying type B radioactive material packages

    Energy Technology Data Exchange (ETDEWEB)

    Easton, E.P. [United States Nuclear Regulatory Commission, Washington, DC (United States); Faille, S. [Canadian Nuclear Safety Commission, Ottawa (Canada)

    2004-07-01

    This paper presents the advantages of adopting well-documented standardized review practices for reviewing Type B package designs. The US experience using standardized review plans and guidance has shown them to be a valuable tool in achieving more consistent and efficient package reviews, in training and qualifying technical reviewers, and in enhancing public and industry understanding of the package certification process. In addition, the standardized review practices, as living documents, have proven to be an effective method of incorporating new technical advances into the review process, and have provided a vehicle to make that knowledge widely available to fellow reviewers, the public and industry. Canada implemented a new internal review process in early 2003 to standardize the review of applications for certification of Type B Packages. Based on the similarity of these approaches, the United States and Canada have started discussions on a A North American System for the unilateral approval of Type B (U) packages. This initiative is looking into how each country is currently reviewing transportation package applications to see if agreement can be reached on accepting Type B certifications on a reciprocal basis, i.e., without additional review. Based on the experience in Canada and the United States, the authors believe that the use of standardized review processes, coupled with the knowledge and experience resident in IAEA's Transportation Advisory Material (TS-G-1.1) and series of TECDOCS, could also be used to develop a standard internationally accepted review process that could enhance the acceptance of unilateral approvals for Type B packages.

  18. A standardized procedure for eddy-current testing of stainless steel, thin-walled nuclear fuel element cladding tubes

    International Nuclear Information System (INIS)

    Barat, P.; Raj, B.; Bhattacharya, D.K.

    1982-01-01

    Thin-walled nuclear fuel cladding tubes made of AISI 316 stainless steel have been examined by eddy-current testing. Standardization of the procedures has required investigations on optimizing the test frequency, finding a method to locate a defect with respect to the probe reference end, and the use of standard defects and sequential metallography of natural defects detected by eddy-current testing, to understand the influence of the nature of defects on the impedance output signals. Test frequency and method of locating the defect were optimized by the use of standard defects made by machining in reference cladding tubes. Subsequent metallography of natural defects detected by eddy-current testing revealed mainly clusters of inclusions but also other types of defects. The effect of the distribution of inclusions along the length of the tube on the impedance output is discussed. (author)

  19. Standardized procedure for eddy-current testing of stainless steel, thin-walled nuclear fuel element cladding tubes

    Energy Technology Data Exchange (ETDEWEB)

    Barat, P; Raj, B; Bhattacharya, D K [Reactor Research Centre, Kalpakkam (India)

    1982-10-01

    Thin-walled nuclear fuel cladding tubes made of AISI 316 stainless steel have been examined by eddy-current testing. Standardization of the procedures has required investigations on optimizing the test frequency, finding a method to locate a defect with respect to the probe reference end, and the use of standard defects and sequential metallography of natural defects detected by eddy-current testing, to understand the influence of the nature of defects on the impedance output signals. Test frequency and method of locating the defect were optimized by the use of standard defects made by machining in reference cladding tubes. Subsequent metallography of natural defects detected by eddy-current testing revealed mainly clusters of inclusions but also other types of defects. The effect of the distribution of inclusions along the length of the tube on the impedance output is discussed.

  20. 78 FR 26103 - Proposed Standard Operating Procedure (SOP) of the Aircraft Certification Service (AIR) Project...

    Science.gov (United States)

    2013-05-03

    ... data, views, or arguments to the above listed address. Please identify ``SOP: AIR-100-001 Standard... Certification Offices (ACOs). The certification programs include: Type certificate (TC), Amended Type Certificate (ATC), Supplemental Type Certificated ATC), Amended Supplemental Type Certificate (ASTC), and...

  1. Study on Design and Implementation of JAVA Programming Procedural Assessment Standard

    Science.gov (United States)

    Tingting, Xu; Hua, Ma; Xiujuan, Wang; Jing, Wang

    2015-01-01

    The traditional JAVA course examination is just a list of questions from which we cannot know students' skills of programming. According to the eight abilities in curriculum objectives, we designed an assessment standard of JAVA programming course that is based on employment orientation and apply it to practical teaching to check the teaching…

  2. Procedure for the standardized measure of the detective quantum efficiency in digital mammography

    International Nuclear Information System (INIS)

    Rodriguez Martin, G.; Garcia Castano, P.; Bermudez Luna, R.; Fernandez Bedoya, V.; Espana Lopez, M. L.; Miquelez Alonso, S.

    2011-01-01

    The objective of this work is to develop a simple guide for determining the DQE, according to the CEI, in those having mammography flat panel detectors, and highlight the main difficulties that may be in the process of the standardized measurement.

  3. An Investigation of Seventh Grade Students’ Performances on Conceptual, Procedural and Graphical Problems Regarding Circles

    Directory of Open Access Journals (Sweden)

    Lütfi İncikabı

    2015-04-01

    Full Text Available The purpose of this study is to determine seventh grade students’ preferences among the procedural, conceptual and graphical questions in the subject of circles, to define their success levels in their preferences, and to compare students’ success levels in one question type with their performances in other question types. The methodology adopted during this research was case study. Based on criterion-based purposive sampling strategy, 98 middle school students were selected as the participants. Data were collected through an achievement test consisting of nine questions (three per question type. The results obtained from the study indicated that students mostly preferred graphical question types. Moreover, majority of students could not succeeded high levels in their preferred question types. In addition, the students performed better in graphical question types; however, the failure in procedural question types was remarkable. Keywords: Multiple representations, middle school students, mathematics education, circles

  4. The procedural learning deficit hypothesis of language learning disorders: we see some problems.

    Science.gov (United States)

    West, Gillian; Vadillo, Miguel A; Shanks, David R; Hulme, Charles

    2018-03-01

    Impaired procedural learning has been suggested as a possible cause of developmental dyslexia (DD) and specific language impairment (SLI). This study examined the relationship between measures of verbal and non-verbal implicit and explicit learning and measures of language, literacy and arithmetic attainment in a large sample of 7 to 8-year-old children. Measures of verbal explicit learning were correlated with measures of attainment. In contrast, no relationships between measures of implicit learning and attainment were found. Critically, the reliability of the implicit learning tasks was poor. Our results show that measures of procedural learning, as currently used, are typically unreliable and insensitive to individual differences. A video abstract of this article can be viewed at: https://www.youtube.com/watch?v=YnvV-BvNWSo. 2017 The Authors. Developmental Science Published by John Wiley & Sons Ltd.

  5. Documentation for assessment of modal pushover-based scaling procedure for nonlinear response history analysis of "ordinary standard" bridges

    Science.gov (United States)

    Kalkan, Erol; Kwong, Neal S.

    2010-01-01

    The earthquake engineering profession is increasingly utilizing nonlinear response history analyses (RHA) to evaluate seismic performance of existing structures and proposed designs of new structures. One of the main ingredients of nonlinear RHA is a set of ground-motion records representing the expected hazard environment for the structure. When recorded motions do not exist (as is the case for the central United States), or when high-intensity records are needed (as is the case for San Francisco and Los Angeles), ground motions from other tectonically similar regions need to be selected and scaled. The modal-pushover-based scaling (MPS) procedure recently was developed to determine scale factors for a small number of records, such that the scaled records provide accurate and efficient estimates of 'true' median structural responses. The adjective 'accurate' refers to the discrepancy between the benchmark responses and those computed from the MPS procedure. The adjective 'efficient' refers to the record-to-record variability of responses. Herein, the accuracy and efficiency of the MPS procedure are evaluated by applying it to four types of existing 'ordinary standard' bridges typical of reinforced-concrete bridge construction in California. These bridges are the single-bent overpass, multi span bridge, curved-bridge, and skew-bridge. As compared to benchmark analyses of unscaled records using a larger catalog of ground motions, it is demonstrated that the MPS procedure provided an accurate estimate of the engineering demand parameters (EDPs) accompanied by significantly reduced record-to-record variability of the responses. Thus, the MPS procedure is a useful tool for scaling ground motions as input to nonlinear RHAs of 'ordinary standard' bridges.

  6. Simulation of international standard problem no. 44 open tests using Melcor computer code

    International Nuclear Information System (INIS)

    Song, Y.M.; Cho, S.W.

    2001-01-01

    MELCOR 1.8.4 code has been employed to simulate the KAEVER test series of K123/K148/K186/K188 that were proposed as open experiments of International Standard Problem No.44 by OECD-CSNI. The main purpose of this study is to evaluate the accuracy of the MELCOR aerosol model which calculates the aerosol distribution and settlement in a containment. For this, thermal hydraulic conditions are simulated first for the whole test period and then the behavior of hygroscopic CsOH/CsI and unsoluble Ag aerosols, which are predominant activity carriers in a release into the containment, is compared between the experimental results and the code predictions. The calculation results of vessel atmospheric concentration show a good simulation for dry aerosol but show large difference for wet aerosol due to a data mismatch in vessel humidity and the hygroscopicity. (authors)

  7. Posttest analysis of international standard problem 10 using RELAP4/MOD7

    International Nuclear Information System (INIS)

    Hsu, M.; Davis, C.B.; Peterson, A.C. Jr.; Behling, S.R.

    1981-01-01

    RELAP4/MOD7, a best estimate computer code for the calculation of thermal and hydraulic phenomena in a nuclear reactor or related system, is the latest version in the RELAP4 code development series. This paper evaluates the capability of RELAP4/MOD7 to calculate refill/reflood phenomena. This evaluation uses the data of International Standard Problem 10, which is based on West Germany's KWU PKL refill/reflood experiment K9A. The PKL test facility represents a typical West German four-loop, 1300 MW pressurized water reactor (PWR) in reduced scale while maintaining prototypical volume-to-power ratio. The PKL facility was designed to specifically simulate the refill/reflood phase of a hypothetical loss-of-coolant accident

  8. MARS-KS code validation activity through the atlas domestic standard problem

    International Nuclear Information System (INIS)

    Choi, K. Y.; Kim, Y. S.; Kang, K. H.; Park, H. S.; Cho, S.

    2012-01-01

    The 2 nd Domestic Standard Problem (DSP-02) exercise using the ATLAS integral effect test data was executed to transfer the integral effect test data to domestic nuclear industries and to contribute to improving the safety analysis methodology for PWRs. A small break loss of coolant accident of a 6-inch break at the cold leg was determined as a target scenario by considering its technical importance and by incorporating interests from participants. Ten calculation results using MARS-KS code were collected, major prediction results were described qualitatively and code prediction accuracy was assessed quantitatively using the FFTBM. In addition, special code assessment activities were carried out to find out the area where the model improvement is required in the MARS-KS code. The lessons from this DSP-02 and recommendations to code developers are described in this paper. (authors)

  9. Disqualification of judge and other procedural problems in the implementation of parole

    Directory of Open Access Journals (Sweden)

    Vuković Nikola

    2016-01-01

    Full Text Available The work is thematically divided into two parts that are not strictly separated. The link between these is the institution of release on parole. The first part deals with the institution of disqualification of a judge from the panel which decides on the petition for release on parole. It was noted that this issue does not occupy the attention of science, nor practice. It is pointed why this neglect is unjustified. Specifically analyzed is the possibility of participation of judge in deciding on release on parole if he has already acted (had some role in the same case before. The consequences that can be brought by insufficient attention on this issue are as follows: 1 substantive violation of the provisions of criminal procedure, and 2 the conduct of disciplinary proceedings against a judge who should have been disqualified. The second part examines certain provisions of legal acts regulating the matter of conditional release. The enormous significance of parole is that the convict has the possibility to get out after 2/3 of served prison sentence. The scale of these opportunity is clearly visible on the long-term prison sentences. Despite the general tendency towards reducing the prison population, it appears that parole does not and can not achieve the role which it intends. The procedure for release on parole in the case law often acts as a 'sideshow' and the CPC opens the door to discussions about the quality of certain provisions of the procedure for release on parole.

  10. NASA Safety Standard: Guidelines and Assessment Procedures for Limiting Orbital Debris

    Science.gov (United States)

    1995-01-01

    Collision with orbital debris is a hazard of growing concern as historically accepted practices and procedures have allowed man-made objects to accumulate in orbit. To limit future debris generation, NASA Management Instruction (NMI) 1700.8, 'Policy to Limit Orbital Debris Generation,' was issued in April of 1993. The NMI requires each program to conduct a formal assessment of the potential to generate orbital debris. This document serves as a companion to NMI 1700.08 and provides each NASA program with specific guidelines and assessment methods to assure compliance with the NMI. Each main debris assessment issue (e.g., Post Mission Disposal) is developed in a separate chapter.

  11. Standardization of solvent extraction procedure for determination of uranium in seawater

    International Nuclear Information System (INIS)

    Sukanta Maity; Sahu, S.K.; Pandit, G.G.

    2015-01-01

    Solvent extraction procedure using ammonium pyrolidine dithiocarbamate complexing agent in methyl isobutyl ketone organic phase and acid exchange back-extraction is described for the simultaneous quantitative pre-concentration of uranium in seawater followed by its determination by differential pulse adsorptive stripping voltammetry. Solvent extraction time is optimized for extraction of uranium from seawater. Solvent extraction efficiency for uranium in seawater at different pH was carried out. The method gives a recovery of 98 ± 2 % for 400 mL sample at pH 3.0 ± 0.02, facilitating the rapid and interference free analysis of seawater samples. (author)

  12. Developing standard performance testing procedures for MC and A components at a site

    International Nuclear Information System (INIS)

    Scherer, Carolynn

    2010-01-01

    The condition of a nuclear material control and accountability system (MC and A) and its individual components, as with any system combining technical elements, documentation and the human factor, may be characterized through an aggregate of values for the various parameters that determine the system's ability to perform. The MC and A system's status may be functioning effectively, marginally or not functioning based on a summary of the values of the individual parameters. This work included a review of the following elements and subsystems or components for a material control and accountability system: (1) MC and A Elements: Information subsystem, Measurement subsystem, NM access subsystem, including a tamper-indicating device (TID) program, and Automated information-gathering subsystem; and (2) Detecting NM Loses Elements: Inventory differences, Shipper/receiver differences, Confirmatory measurements and differences with accounting data, and TID or seal violations. In order to detect the absence or loss of nuclear material there must be appropriate interactions among the elements and their respective subsystems (from the list above). Additionally this work includes a review of the status of regulatory requirements for the MC and A system components and potential criteria that support the evaluation of the performance of the listed components. The listed components had performance testing algorithms and procedures developed that took into consideration the regulatory criteria. The developed MC and A performance-testing procedures were the basis for a pilot Guide for MC and A Performance Testing at the MBAs of SSC RF IPPE.

  13. A Standardized Procedure for a Pre-evaluation of the IED Instance

    Science.gov (United States)

    Panepinto, Deborah; Ruffino, Barbara; Zanetti, Mariachiara; Genon, Giuseppe

    2016-04-01

    This study presents a procedure, called EICS (Enterprise IPPC Compatibility Study) aimed at evaluating, by means of the calculation of three indexes, the compliance of the processes performed in an industrial plant with the guidelines provided by BREFs (BAT References) Documents. In fact, according to European Directive 2010/75/EU (concerning the Integrated Pollution Prevention and Control and repealing European Directive 2008/01/EC), industrial plants must require authorizations to the competent authority stating the conformity of their activity, in order to obtain this conformity they are advised to Best Available Technologies (BAT). The aim of the BATs is to avoid or minimize the impact of an industrial activity on the environment through the prevention of the atmospheric emissions, wastewater discharge and energetic consumption, and the correct waste management thus improving the efficiency of the plant. The procedure shown in the present paper has been tested on several types of industrial plant (cement plants, secondary smelt foundries, paper-mill, and automotive industries as regards their paint lines). In this paper, the application of EICS method to a cement plant is presented: the obtained results highlight a good correlation between the index values and the real situation of the plant.

  14. Problems of standardizing and technical regulation in the electric power industry

    Science.gov (United States)

    Grabchak, E. P.

    2016-12-01

    A mandatory condition to ensure normal operation of a power system and efficiency in the sector is standardization and legal regulation of technological activities of electric power engineering entities and consumers. Compared to the times of USSR, the present-time technical guidance documents are not mandatory to follow in most cases, being of an advisory nature due to the lack of new ones. During the last five years, the industry has been showing a deterioration of the situation in terms of ensuring reliability and engineering controllability as a result of the dominant impact of short-term market stimuli and the differences in basic technological policies. In absence of clear requirements regarding the engineering aspects of such activities, production operation does not contribute to the preserving of technical integrity of the Russian power system, which leads to the loss of performance capability and controllability and causes disturbances in the power supply to consumers. The result of this problem is a high rate of accident incidence. The dynamics of accidents by the type of equipment is given, indicating a persisting trend of growth in the number of accidents, which are of a systematic nature. Several problematic aspects of engineering activities of electric power engineering entities, requiring standardization and legal regulation are pointed out: in the domestic power system, a large number of power electrotechnical and generating equipment operate along with systems of regulation, which do not comply with the principles and technical rules representing a framework where the Energy System of Russia is built and functioning

  15. A standard diagnostic and education procedure for nurses in recognizing the symptoms of aging man

    Directory of Open Access Journals (Sweden)

    Korol Agnieszka

    2017-03-01

    Full Text Available Introduction. In the aging process a weakening of the multiple organ systems and endocrine system occur, which in turn, leads to male hormones deficiency – androgens release, including testosterone. It is believed that the year-to-year, women awareness of the menopausal problems increases, however, their knowledge of the consequences of menopause is still insufficient. Unfortunately, only a small percentage of the population is aware that the same problem can also affect men. Male menopause symptoms are still largely an area of social taboo subject, which is not discussed at all or very little. As a consequence, men are not informed, enlightened, and therefore also ready for the changes that are to take place in themselves and their lives.

  16. “Heidelberg standard examination” and “Heidelberg standard procedures” – Development of faculty-wide standards for physical examination techniques and clinical procedures in undergraduate medical education

    Science.gov (United States)

    Nikendei, C.; Ganschow, P.; Groener, J. B.; Huwendiek, S.; Köchel, A.; Köhl-Hackert, N.; Pjontek, R.; Rodrian, J.; Scheibe, F.; Stadler, A.-K.; Steiner, T.; Stiepak, J.; Tabatabai, J.; Utz, A.; Kadmon, M.

    2016-01-01

    The competent physical examination of patients and the safe and professional implementation of clinical procedures constitute essential components of medical practice in nearly all areas of medicine. The central objective of the projects “Heidelberg standard examination” and “Heidelberg standard procedures”, which were initiated by students, was to establish uniform interdisciplinary standards for physical examination and clinical procedures, and to distribute them in coordination with all clinical disciplines at the Heidelberg University Hospital. The presented project report illuminates the background of the initiative and its methodological implementation. Moreover, it describes the multimedia documentation in the form of pocketbooks and a multimedia internet-based platform, as well as the integration into the curriculum. The project presentation aims to provide orientation and action guidelines to facilitate similar processes in other faculties. PMID:27579354

  17. Radioisotopic studies concerning the efficacy of standard washing procedures for the cleansing of hair before zinc analysis

    International Nuclear Information System (INIS)

    Buckley, R.A.; Dreosti, I.E.

    1984-01-01

    Various standard procedures were investigated in relation to the removal of exogenously applied 65Zn from human hair and endogenously incorporated 65Zn from rat hair. Human hair was found to adsorb zinc and a variety of other metal ions from aqueous solutions in a manner which suggested some ion-exchange capacity. Uptake of zinc varied considerably between human hair samples, but in most cases accumulation of zinc occurred rapidly and often resulted in hair zinc levels several-fold higher than found in control samples. Extraction of zinc and other metal ions was greatest after treatment with disodium EDTA and sodium lauryl sulfate than after washing with water or aqueous Triton X-100. However, no procedure effectively removed all exogenous zinc, while all treatments extracted varying proportions of the endogenous zinc component. Because of the inability of standard washing procedures to remove exogenous zinc without reducing endogenous or indicator zinc levels, use of hair zinc analyses to indicate nutritional zinc status are inadvisable if hair zinc contamination is likely to have occurred

  18. The Use of Procedural Knowledge in Simple Addition and Subtraction Problems

    Science.gov (United States)

    Fayol, Michel; Thevenot, Catherine

    2012-01-01

    In a first experiment, adults were asked to solve one-digit additions, subtractions and multiplications. When the sign appeared 150 ms before the operands, addition and subtraction were solved faster than when the sign and the operands appeared simultaneously on screen. This priming effect was not observed for multiplication problems. A second…

  19. The radiopharmaceuticals in nuclear medicine diagnostic procedures and the problem of radiation protection

    Energy Technology Data Exchange (ETDEWEB)

    Ftacnikova, S [Inst. of Preventive and Clinical Medicine, 83301 Bratislava (Slovakia)

    1996-12-31

    In this paper equivalent dose from Auger electron emitters was reevaluated. The presented approach represents a practical step toward the estimation of equivalent dose for incorporated Auger electron emitters, an aspects that has not been given adequate consideration so far. Given the widespread use of this class of radionuclides in nuclear medicine and in biomedical research, the formalism and practical calculation presented here may be of value to assessing the risk associated with this radionuclides (in diagnostic nuclear medicine procedures), as well as predicting their therapeutic efficiency. (J.K.) 2 tabs., 11 refs.

  20. The protection of juveniles under Cameroon criminal law and procedures through the lens of international standards

    Directory of Open Access Journals (Sweden)

    Thomas Ojong

    2017-10-01

    Full Text Available While the legislative framework on the adminitration of juvenile justice in Cameroon may currently be adequate and in compliance with the international conventions ratified by the State, the implementation of the national law should be the primary mechanism through which human rights are realized. Cameroon is usually said to be a State with good laws but poor implementation. With recourse to the normative and empirical methods, this article explores the provisions on the protection of juveniles in Cameroon criminal law and procedures through the lens of internationally recognized principles. It looks at the provisions as they are interpreted and applied by the Courts. The prospect being to invite the Government and all the stakeholders to embark on establishing the structures provided for and ensure effectiveness in the enforcement of juvenile justice in the country so as to overcome the current weaknesses that the system is experiencing.

  1. Control protocol: the proposed new CERN standard access procedure to accelerator equipment

    International Nuclear Information System (INIS)

    Baribaud, G.; Barnett, I.; Benincasa, G.

    1992-01-01

    Control protocol provides a normalized access procedure for equipment of the same kind from a control system. Modelisation and the subsequent identification of functionalities with their parameters, variables and attributes have now been carried out at CERN for representative families of devices. ISO specifications, such as the ASN.1 metalanguage for data structure representation and MMS definitions and services have, to some extent, been introduced in the design for generality and compatibility with external world. The final product of this design is totally independent of the control systems and permits object oriented implementations in any controls frame. The present paper describes the different phases of the project with a short overview of the various implementations under development at CERN. (author)

  2. Developing standard performance testing procedures for material control and accounting components at a site

    International Nuclear Information System (INIS)

    Scherer, Carolynn P.; Bushlya, Anatoly V.; Efimenko, Vladimir F.; Ilyanstev, Anatoly; Regoushevsky, Victor I.

    2010-01-01

    The condition of a nuclear material control and accountability system (MC and A) and its individual components, as with any system combining technical elements and documentation, may be characterized through an aggregate of values for the various parameters that determine the system's ability to perform. The MC and A system's status may be functioning effectively, marginally or not functioning based on a summary of the values of the individual parameters. This work included a review of the following subsystems, MC and A and Detecting Material Losses, and their respective elements for the material control and accountability system: (a) Elements of the MC and A Subsystem - Information subsystem (Accountancy/Inventory), Measurement subsystem, Nuclear Material Access subsystem, including tamper-indicating device (TID) program, and Automated Information-gathering subsystem; (b) Elements for Detecting Nuclear Material Loses Subsystem - Inventory Differences, Shipper/receiver Differences, Confirmatory Measurements and differences with accounting data, and TID or Seal Violations. In order to detect the absence or loss of nuclear material there must be appropriate interactions among the elements and their respective subsystems from the list above. Additionally this work includes a review of regulatory requirements for the MC and A system component characteristics and criteria that support the evaluation of the performance of the listed components. The listed components had performance testing algorithms and procedures developed that took into consideration the regulatory criteria. The developed MC and A performance-testing procedures were the basis for a Guide for MC and A Performance Testing at the material balance areas (MBAs) of State Scientific Center of the Russian Federation - Institute for Physics and Power Engineering (SSC RF-IPPE).

  3. The use of faces as stimuli in neuroimaging and psychological experiments: a procedure to standardize stimulus features.

    Science.gov (United States)

    Gronenschild, Ed H B M; Smeets, Floortje; Vuurman, Eric F P M; van Boxtel, Martin P J; Jolles, Jelle

    2009-11-01

    In psychological experiments involving facial stimuli, it is of great importance that the basic perceptual or psychological characteristics that are investigated are not confounded by factors such as brightness and contrast, head size, hair cut and color, skin color, and the presence of glasses and earrings. Standardization of facial stimulus materials reduces the effect of these confounding factors. We therefore employed a set of basic image processing techniques to deal with this issue. The processed images depict the faces in grayscale, all at the same size, brightness, and contrast, and confined to an oval mask revealing only the basic features such as the eyes, nose, and mouth. The standardization was successfully applied to four different face databases, consisting of male and female faces and including neutral as well as happy facial expressions. An important advantage of the proposed standardization is that featural as well as configurational information is retained. We also consider the procedure to be a major contribution to the development of a de facto standard for the use of facial stimuli in psychological experiments. Such methodological standardization would allow a better comparison of the results of these studies.

  4. Elaboration and implementation of standard operational procedure for quality assurance of cone beam CT image in radiotherapy

    International Nuclear Information System (INIS)

    Bonatto, Larisse N.; Estacio, Daniela R.; Lopes, Juliane S.; Sansson, Angela; Duarte, Lucas O.; Sbaraini, Patricia; Silva, Ana M. Marques da; Streck, Elaine E.

    2016-01-01

    The objective of this article is to present the implementation of the quality Control of Cone Beam Computed Tomography (CBCT) image, generated by the On-Board Imager, integrated with the linear accelerator Trilogy. Standard operating procedures (POPs) have been developed based on the literature and manuals of the simulator object Catphan 504 and the On-Board Imager. The following POPs were developed: acquisition of the CBCT image; linearity of CT number; uniformity; spatial resolution; low contrast resolution; spatial linearity; thickness of the cut. The validation of the elaborated procedures was done from an experimental acquisition of the simulator object. The results obtained in the validation of the POPs are in compliance with the parameters established by the manufacturer of the simulator object, as well as those obtained in the acceptance of the On-Board Imager device.

  5. Pupils' Visual Representations in Standard and Problematic Problem Solving in Mathematics: Their Role in the Breach of the Didactical Contract

    Science.gov (United States)

    Deliyianni, Eleni; Monoyiou, Annita; Elia, Iliada; Georgiou, Chryso; Zannettou, Eleni

    2009-01-01

    This study investigated the modes of representations generated by kindergarteners and first graders while solving standard and problematic problems in mathematics. Furthermore, it examined the influence of pupils' visual representations on the breach of the didactical contract rules in problem solving. The sample of the study consisted of 38…

  6. Colloidal Fouling of Nanofiltration Membranes: Development of a Standard Operating Procedure

    Directory of Open Access Journals (Sweden)

    Md Abdullaha Al Mamun

    2017-01-01

    Full Text Available Fouling of nanofiltration (NF membranes is the most significant obstacle to the development of a sustainable and energy-efficient NF process. Colloidal fouling and performance decline in NF processes is complex due to the combination of cake formation and salt concentration polarization effects, which are influenced by the properties of the colloids and the membrane, the operating conditions of the test, and the solution chemistry. Although numerous studies have been conducted to investigate the influence of these parameters on the performance of the NF process, the importance of membrane preconditioning (e.g., compaction and equilibrating with salt water, as well as the determination of key parameters (e.g., critical flux and trans-membrane osmotic pressure before the fouling experiment have not been reported in detail. The aim of this paper is to present a standard experimental and data analysis protocol for NF colloidal fouling experiments. The developed methodology covers preparation and characterization of water samples and colloidal particles, pre-test membrane compaction and critical flux determination, measurement of experimental data during the fouling test, and the analysis of that data to determine the relative importance of various fouling mechanisms. The standard protocol is illustrated with data from a series of flat sheet, bench-scale experiments.

  7. Assessment of modal-pushover-based scaling procedure for nonlinear response history analysis of ordinary standard bridges

    Science.gov (United States)

    Kalkan, E.; Kwong, N.

    2012-01-01

    The earthquake engineering profession is increasingly utilizing nonlinear response history analyses (RHA) to evaluate seismic performance of existing structures and proposed designs of new structures. One of the main ingredients of nonlinear RHA is a set of ground motion records representing the expected hazard environment for the structure. When recorded motions do not exist (as is the case in the central United States) or when high-intensity records are needed (as is the case in San Francisco and Los Angeles), ground motions from other tectonically similar regions need to be selected and scaled. The modal-pushover-based scaling (MPS) procedure was recently developed to determine scale factors for a small number of records such that the scaled records provide accurate and efficient estimates of “true” median structural responses. The adjective “accurate” refers to the discrepancy between the benchmark responses and those computed from the MPS procedure. The adjective “efficient” refers to the record-to-record variability of responses. In this paper, the accuracy and efficiency of the MPS procedure are evaluated by applying it to four types of existing Ordinary Standard bridges typical of reinforced concrete bridge construction in California. These bridges are the single-bent overpass, multi-span bridge, curved bridge, and skew bridge. As compared with benchmark analyses of unscaled records using a larger catalog of ground motions, it is demonstrated that the MPS procedure provided an accurate estimate of the engineering demand parameters (EDPs) accompanied by significantly reduced record-to-record variability of the EDPs. Thus, it is a useful tool for scaling ground motions as input to nonlinear RHAs of Ordinary Standard bridges.

  8. Procedures followed in the evaluation of a LWR plant in Spain and problems encountered

    International Nuclear Information System (INIS)

    Brincones, M.; Gea, A.; Perez del Moral, C.

    1979-01-01

    The main problems arising in the safety assessment of nuclear power plants based on the experience of the authors (project managers) and to recomend possible improvements both for Spain and other developing countries are described. The first part will be devoted to the organizative aspects of the assessment and the second part will deal with different possible methods of technical assessment and its associated necesities. Finally, as a result of the previous considerations some recomendations in order to improve the technical assessment practice are proposed. (author)

  9. On the physical problem of spatial dimensions: an alternative procedure to stability arguments

    International Nuclear Information System (INIS)

    Caruso, F.; Xavier, R.M.

    1986-01-01

    The three-dimensionality of space as a physical problem is discussed. Consideration on previous works is done, in which it is showed that the n-dimensional solar system can be stable only for n=3 and, from quantum mechanics, that this is the case also for hydrogen atons. Thus the epistemological consequences of the use of the stability postulate to derive spatial dimensionality is critically reviewed. The distinguished role of Maxwell's eletromagnetic theory in the determination of space dimensionality is stressed. 'Metric versus' 'topological' 'arguments are compared and shown to apply respectively to 'matter' and 'fields'. (G.D.F.) [pt

  10. Verification of thermal-hydraulic computer codes against standard problems for WWER reflooding

    International Nuclear Information System (INIS)

    Alexander D Efanov; Vladimir N Vinogradov; Victor V Sergeev; Oleg A Sudnitsyn

    2005-01-01

    Full text of publication follows: The computational assessment of reactor core components behavior under accident conditions is impossible without knowledge of the thermal-hydraulic processes occurring in this case. The adequacy of the results obtained using the computer codes to the real processes is verified by carrying out a number of standard problems. In 2000-2003, the fulfillment of three Russian standard problems on WWER core reflooding was arranged using the experiments on full-height electrically heated WWER 37-rod bundle model cooldown in regimes of bottom (SP-1), top (SP-2) and combined (SP-3) reflooding. The representatives from the eight MINATOM's organizations took part in this work, in the course of which the 'blind' and posttest calculations were performed using various versions of the RELAP5, ATHLET, CATHARE, COBRA-TF, TRAP, KORSAR computer codes. The paper presents a brief description of the test facility, test section, test scenarios and conditions as well as the basic results of computational analysis of the experiments. The analysis of the test data revealed a significantly non-one-dimensional nature of cooldown and rewetting of heater rods heated up to a high temperature in a model bundle. This was most pronounced at top and combined reflooding. The verification of the model reflooding computer codes showed that most of computer codes fairly predict the peak rod temperature and the time of bundle cooldown. The exception is provided by the results of calculations with the ATHLET and CATHARE codes. The nature and rate of rewetting front advance in the lower half of the bundle are fairly predicted practically by all computer codes. The disagreement between the calculations and experimental results for the upper half of the bundle is caused by the difficulties of computational simulation of multidimensional effects by 1-D computer codes. In this regard, a quasi-two-dimensional computer code COBRA-TF offers certain advantages. Overall, the closest

  11. Results of international standard problem No. 36 severe fuel damage experiment of a VVER fuel bundle

    Energy Technology Data Exchange (ETDEWEB)

    Firnhaber, M. [Gesellschaft fuer Anlagen-und Reaktorsicherheit, Koeln (Germany); Yegorova, L. [Nuclear Safety Institute of Russian Research Center, Moscow (Russian Federation); Brockmeier, U. [Ruhr-Univ. of Bochum (Germany)] [and others

    1995-09-01

    International Standard Problems (ISP) organized by the OECD are defined as comparative exercises in which predictions with different computer codes for a given physical problem are compared with each other and with a carefully controlled experimental study. The main goal of ISP is to increase confidence in the validity and accuracy of analytical tools used in assessing the safety of nuclear installations. In addition, it enables the code user to gain experience and to improve his competence. This paper presents the results and assessment of ISP No. 36, which deals with the early core degradation phase during an unmitigated severe LWR accident in a Russian type VVER. Representatives of 17 organizations participated in the ISP using the codes ATHLET-CD, ICARE2, KESS-III, MELCOR, SCDAP/RELAP5 and RAPTA. Some participants performed several calculations with different codes. As experimental basis the severe fuel damage experiment CORA-W2 was selected. The main phenomena investigated are thermal behavior of fuel rods, onset of temperature escalation, material behavior and hydrogen generation. In general, the calculations give the right tendency of the experimental results for the thermal behavior, the hydrogen generation and, partly, for the material behavior. However, some calculations deviate in important quantities - e.g. some material behavior data - showing remarkable discrepancies between each other and from the experiments. The temperature history of the bundle up to the beginning of significant oxidation was calculated quite well. Deviations seem to be related to the overall heat balance. Since the material behavior of the bundle is to a great extent influenced by the cladding failure criteria a more realistic cladding failure model should be developed at least for the detailed, mechanistic codes. Regarding the material behavior and flow blockage some models for the material interaction as well as for relocation and refreezing requires further improvement.

  12. Efficient Greedy Randomized Adaptive Search Procedure for the Generalized Regenerator Location Problem

    Directory of Open Access Journals (Sweden)

    J.D. Quintana

    2016-12-01

    Full Text Available Over the years, there has been an evolution in the manner in which we perform traditional tasks. Nowadays, almost every simple action that we can think about involves the connection among two or more devices. It is desirable to have a high quality connection among devices, by using electronic or optical signals. Therefore, it is really important to have a reliable connection among terminals in the network. However, the transmission of the signal deteriorates when increasing the distance among devices. There exists a special piece of equipment that we can deploy in a network, called regenerator, which is able to restore the signal transmitted through it, in order to maintain its quality. Deploying a regenerator in a network is generally expensive, so it is important to minimize the number of regenerators used. In this paper we focus on the Generalized Regenerator Location Problem (GRLP, which tries to innd the minimum number of regenerators that must be deployed in a network in order to have a reliable communication without loss of quality. We present a GRASP metaheuristic in order to innd good solutions for the GRLP. The results obtained by the proposal are compared with the best previous methods for this problem. We conduct an extensive computational experience with 60 large and challenging instances, emerging the proposed method as the best performing one. This fact is innally supported by non-parametric statistical tests.

  13. STANDARDIZATION OF PROCEDURES OF Plasmodium falciparum ANTIGEN PREPARATION FOR SEROLOGIC TESTS

    Directory of Open Access Journals (Sweden)

    Sandra L.M. AVILA

    1998-09-01

    Full Text Available The objective of the present study is to standardize the technical variables for preparation and storage of Plasmodium falciparum and of antigen components extracted with the amphoteric detergent Zwittergent. P. falciparum obtained from in vitro culture was stored at different temperatures and for different periods of time. For each variable, antigen components of the parasite were extracted in the presence or absence of protease inhibitors and submitted or not to later dialysis. Products were stored for 15, 30 and 60 days at different temperatures and immunological activity of each extract was determined by SDS-PAGE and ELISA using positive or negative standard sera for the presence of IgG directed to blood stage antigens of P. falciparum. Antigen extracts obtained from parasites stored at -20oC up to 10 days or at -70oC for 2 months presented the best results, showing well-defined bands on SDS-PAGE and Western blots and presenting absorbance values in ELISA that permitted safe differentiation between positive and negative sera.O objetivo deste estudo foi padronizar variáveis técnicas para o armazenamento de Plasmodium falciparum e de seus componentes antigênicos. Sedimentos de parasitas foram obtidos do cultivo in vitro de P.falciparum e estocados em diferentes temperaturas por diferentes períodos de tempo. De cada variável, foram extraídos os componentes antigênicos com detergente anfótero Zwittergent na presença e na ausência de inibidores de proteases e submetidos ou não a posterior diálise. Os produtos foram estocados por 15, 30 e 60 dias em diferentes temperaturas e caracterizados por SDS-PAGE. A atividade antigênica de cada extrato foi determinada por ELISA e Western blotting usando soros positivos e negativos para anticorpos IgG anti-formas eritrocitárias de P.falciparum. Os extratos antigênicos obtidos de parasitas estocados até 10 dias a _20ºC ou por 2 meses a _70ºC e tratados com inibidores de proteases, sob as

  14. OIE philosophy, policy and procedures for the development of food safety standards.

    Science.gov (United States)

    Droppers, W F G L

    2006-08-01

    Food safety was identified as a high priority area in the 2001-2005 World Organisation for Animal Health (OIE) Strategic Plan. Member Countries of the OIE considered that the organisation should be more active in issues of public health and consumer protection and that this should include more involvement in the area of diseases or pathogens transmissible through food, whether or not animals are affected by such diseases or pathogens. A permanent Working Group on Animal Production Food Safety was established in 2002 to coordinate the OIE's activities in food safety. The Working Group was requested to focus on food safety measures applicable at farm level and to monitor the ongoing cooperation between the OIE and Codex Alimentarius. More emphasis is now placed on the public health aspects of a disease when OIE standards are developed or revised. For example, the revised chapter on bovine tuberculosis in the Terrestrial Animal Health Code includes food safety recommendations for meat and meat products and for milk and milk products. The revised chapter was approved by the OIE International Committee of Member Countries at their 73rd General Session in May 2005. More chapters will follow, beginning with a chapter addressing bovine brucellosis.

  15. Procedures for Measuring Women's Influence: Data translation and manipulation and related problems

    Directory of Open Access Journals (Sweden)

    Penelope Allison

    2008-07-01

    Full Text Available Preparing data from artefact catalogues of previously published German excavation reports, in the project 'Engendering Roman Spaces', required ongoing refinement of data translation and digital manipulation using a variety of software packages. This process included the use of Optical Character Recognition (OCR software, spreadsheets, database and graphics programs, and the final presentation of the data in ArcGIS as an interpretative tool. With each step, a number of challenges were encountered relating to the quality of the data and original cataloguing processes, and the limitations of the software packages being used. Excavation reports of four Roman military sites - the forts of Vetera I, Ellingen, Oberstimm and Rottweil - are used in this article to highlight the range of problems encountered and solutions arrived to resolve them, a process requiring constant revision and refinement.

  16. SECOND ATLAS DOMESTIC STANDARD PROBLEM (DSP-02 FOR A CODE ASSESSMENT

    Directory of Open Access Journals (Sweden)

    YEON-SIK KIM

    2013-12-01

    Full Text Available KAERI (Korea Atomic Energy Research Institute has been operating an integral effect test facility, the Advanced Thermal-Hydraulic Test Loop for Accident Simulation (ATLAS, for transient and accident simulations of advanced pressurized water reactors (PWRs. Using ATLAS, a high-quality integral effect test database has been established for major design basis accidents of the APR1400 plant. A Domestic Standard Problem (DSP exercise using the ATLAS database was promoted to transfer the database to domestic nuclear industries and contribute to improving a safety analysis methodology for PWRs. This 2nd ATLAS DSP (DSP-02 exercise aims at an effective utilization of an integral effect database obtained from ATLAS, the establishment of a cooperation framework among the domestic nuclear industry, a better understanding of the thermal hydraulic phenomena, and an investigation into the possible limitation of the existing best-estimate safety analysis codes. A small break loss of coolant accident with a 6-inch break at the cold leg was determined as a target scenario by considering its technical importance and by incorporating interests from participants. This DSP exercise was performed in an open calculation environment where the integral effect test data was open to participants prior to the code calculations. This paper includes major information of the DSP-02 exercise as well as comparison results between the calculations and the experimental data.

  17. The 3rd ATLAS Domestic Standard Problem for Improvement of Safety Analysis Technology

    International Nuclear Information System (INIS)

    Choi, Ki-Yong; Kang, Kyoung-Ho; Park, Yusun; Kim, Jongrok; Bae, Byoung-Uhn; Choi, Nam-Hyun

    2014-01-01

    The third ATLAS DSP (domestic standard problem exercise) was launched at the end of 2012 in response to the strong need for continuation of the ATLAS DSP. A guillotine break of a main steam line without LOOP at a zero power condition was selected as a target scenario, and it was successfully completed in the beginning of 2014. In the 3 rd ATLAS DSP, comprehensive utilization of the integral effect test data was made by dividing analysis with three topics; 1. scale-up where extrapolation of ATLAS IET data was investigated 2. 3D analysis where how much improvement can be obtained by 3D modeling was studied 3. 1D sensitivity analysis where the key phenomena affecting the SLB simulation were identified and the best modeling guideline was achieved. Through such DSP exercises, it has been possible to effectively utilize high-quality ATLAS experimental data of to enhance thermal-hydraulic understanding and to validate the safety analysis codes. A strong human network and technical expertise sharing among the various nuclear experts are also important outcomes from this program

  18. Second ATLAS Domestic Standard Problem (DSP-02) For A Code Assessment

    International Nuclear Information System (INIS)

    Kim, Yeonsik; Choi, Kiyong; Cho, Seok; Park, Hyunsik; Kang, Kyungho; Song, Chulhwa; Baek, Wonpil

    2013-01-01

    KAERI (Korea Atomic Energy Research Institute) has been operating an integral effect test facility, the Advanced Thermal-Hydraulic Test Loop for Accident Simulation (ATLAS), for transient and accident simulations of advanced pressurized water reactors (PWRs). Using ATLAS, a high-quality integral effect test database has been established for major design basis accidents of the APR1400 plant. A Domestic Standard Problem (DSP) exercise using the ATLAS database was promoted to transfer the database to domestic nuclear industries and contribute to improving a safety analysis methodology for PWRs. This 2 nd ATLAS DSP (DSP-02) exercise aims at an effective utilization of an integral effect database obtained from ATLAS, the establishment of a cooperation framework among the domestic nuclear industry, a better understanding of the thermal hydraulic phenomena, and an investigation into the possible limitation of the existing best-estimate safety analysis codes. A small break loss of coolant accident with a 6-inch break at the cold leg was determined as a target scenario by considering its technical importance and by incorporating interests from participants. This DSP exercise was performed in an open calculation environment where the integral effect test data was open to participants prior to the code calculations. This paper includes major information of the DSP-02 exercise as well as comparison results between the calculations and the experimental data

  19. International standard problem (ISP) no. 41 follow up exercise: Containment iodine computer code exercise: parametric studies

    Energy Technology Data Exchange (ETDEWEB)

    Ball, J.; Glowa, G.; Wren, J. [Atomic Energy of Canada Limited, Chalk River, Ontario (Canada); Ewig, F. [GRS Koln (Germany); Dickenson, S. [AEAT, (United Kingdom); Billarand, Y.; Cantrel, L. [IPSN (France); Rydl, A. [NRIR (Czech Republic); Royen, J. [OECD/NEA (France)

    2001-11-01

    This report describes the results of the second phase of International Standard Problem (ISP) 41, an iodine behaviour code comparison exercise. The first phase of the study, which was based on a simple Radioiodine Test Facility (RTF) experiment, demonstrated that all of the iodine behaviour codes had the capability to reproduce iodine behaviour for a narrow range of conditions (single temperature, no organic impurities, controlled pH steps). The current phase, a parametric study, was designed to evaluate the sensitivity of iodine behaviour codes to boundary conditions such as pH, dose rate, temperature and initial I{sup -} concentration. The codes used in this exercise were IODE(IPSN), IODE(NRIR), IMPAIR(GRS), INSPECT(AEAT), IMOD(AECL) and LIRIC(AECL). The parametric study described in this report identified several areas of discrepancy between the various codes. In general, the codes agree regarding qualitative trends, but their predictions regarding the actual amount of volatile iodine varied considerably. The largest source of the discrepancies between code predictions appears to be their different approaches to modelling the formation and destruction of organic iodides. A recommendation arising from this exercise is that an additional code comparison exercise be performed on organic iodide formation, against data obtained front intermediate-scale studies (two RTF (AECL, Canada) and two CAIMAN facility, (IPSN, France) experiments have been chosen). This comparison will allow each of the code users to realistically evaluate and improve the organic iodide behaviour sub-models within their codes. (author)

  20. International standard problem (ISP) no. 41 follow up exercise: Containment iodine computer code exercise: parametric studies

    International Nuclear Information System (INIS)

    Ball, J.; Glowa, G.; Wren, J.; Ewig, F.; Dickenson, S.; Billarand, Y.; Cantrel, L.; Rydl, A.; Royen, J.

    2001-11-01

    This report describes the results of the second phase of International Standard Problem (ISP) 41, an iodine behaviour code comparison exercise. The first phase of the study, which was based on a simple Radioiodine Test Facility (RTF) experiment, demonstrated that all of the iodine behaviour codes had the capability to reproduce iodine behaviour for a narrow range of conditions (single temperature, no organic impurities, controlled pH steps). The current phase, a parametric study, was designed to evaluate the sensitivity of iodine behaviour codes to boundary conditions such as pH, dose rate, temperature and initial I - concentration. The codes used in this exercise were IODE(IPSN), IODE(NRIR), IMPAIR(GRS), INSPECT(AEAT), IMOD(AECL) and LIRIC(AECL). The parametric study described in this report identified several areas of discrepancy between the various codes. In general, the codes agree regarding qualitative trends, but their predictions regarding the actual amount of volatile iodine varied considerably. The largest source of the discrepancies between code predictions appears to be their different approaches to modelling the formation and destruction of organic iodides. A recommendation arising from this exercise is that an additional code comparison exercise be performed on organic iodide formation, against data obtained front intermediate-scale studies (two RTF (AECL, Canada) and two CAIMAN facility, (IPSN, France) experiments have been chosen). This comparison will allow each of the code users to realistically evaluate and improve the organic iodide behaviour sub-models within their codes. (author)

  1. On physics of the hydrogen plasticization and embrittlement of metallic materials, relevance to the safety and standards' problems

    International Nuclear Information System (INIS)

    Yury S Nechaev; Georgy A Filippov; T Nejat Veziroglu

    2006-01-01

    In the present contribution, some related fundamental problems of revealing micro mechanisms of hydrogen plasticization, superplasticity, embrittlement, cracking, blistering and delayed fracture of some technologically important industrial metallic materials are formulated. The ways are considered of these problems' solution and optimizing the technological processes and materials, particularly in the hydrogen and gas-petroleum industries, some aircraft, aerospace and automobile systems. The results are related to the safety and standardization problems of metallic materials, and to the problem of their compatibility with hydrogen. (authors)

  2. Compressed air tunneling and caisson work decompression procedures: development, problems, and solutions.

    Science.gov (United States)

    Kindwall, E P

    1997-01-01

    Multinational experience over many years indicates that all current air decompression schedules for caisson and compressed air tunnel workers are inadequate. All of them, including the Occupational Safety and Health Administration tables, produce dysbaric osteonecrosis. The problem is compounded because decompression sickness (DCS) tends to be underreported. Permanent damage in the form of central nervous system or brain damage may occur in compressed air tunnel workers, as seen on magnetic resonance imaging, in addition to dysbaric osteonecrosis. Oxygen decompression seems to be the only viable method for safely decompressing tunnel workers. Oxygen decompression of tunnel workers has been successfully used in Germany, France, and Brazil. In Germany, only oxygen decompression of compressed air workers is permitted. In our experience, U.S. Navy tables 5 and 6 usually prove adequate to treat DCS in caisson workers despite extremely long exposure times, allowing patients to return to work following treatment for DCS. Tables based on empirical data and not on mathematical formulas seem to be reasonably safe. U.S. Navy Exceptional Exposure Air Decompression tables are compared with caisson tables from the United States and Great Britain.

  3. [Research progress on standards of commodity classes of Chinese materia medica and discussion on several key problems].

    Science.gov (United States)

    Yang, Guang; Zeng, Yan; Guo, Lan-Ping; Huang, Lu-Qi; Jin, Yan; Zheng, Yu-Guang; Wang, Yong-Yan

    2014-05-01

    Standards of commodity classes of Chinese materia medica is an important way to solve the "Lemons Problem" of traditional Chinese medicine market. Standards of commodity classes are also helpful to rebuild market mechanisms for "high price for good quality". The previous edition of commodity classes standards of Chinese materia medica was made 30 years ago. It is no longer adapted to the market demand. This article researched progress on standards of commodity classes of Chinese materia medica. It considered that biological activity is a better choice than chemical constituents for standards of commodity classes of Chinese materia medica. It is also considered that the key point to set standards of commodity classes is finding the influencing factors between "good quality" and "bad quality". The article also discussed the range of commodity classes of Chinese materia medica, and how to coordinate standards of pharmacopoeia and commodity classes. According to different demands, diversiform standards can be used in commodity classes of Chinese materia medica, but efficacy is considered the most important index of commodity standard. Decoction pieces can be included in standards of commodity classes of Chinese materia medica. The authors also formulated the standards of commodity classes of Notoginseng Radix as an example, and hope this study can make a positive and promotion effect on traditional Chinese medicine market related research.

  4. A novel elevated plus-maze procedure to avoid the one-trial tolerance problem

    Directory of Open Access Journals (Sweden)

    Peggy eSchneider

    2011-07-01

    Full Text Available The elevated plus-maze (EPM test is one of the most commonly used behavioural assays to evaluate anxiety-related behaviour in rodents. It is a rather economic test which usually uses a short (5 min protocol and does not require conditioning of the animals. The critical measure for anxiety is the time spent in the open arms of the maze. A confounding problem of the EPM is the so called one-trial tolerance (OTT, characterised by a marked decrease of open arm exploration in spite of treatment with anxiolytic acting benzodiazepines upon re-exposure to the EPM. This consistent finding is often raised as an evidence for the inappropriateness to re-test rodents in the EPM. However, a reliable re-test paradigm would broaden the usability and effectiveness of this test.Therefore, we tested how a prolongation of the inter-trial interval to 28 days (instead of the usual 24 hours, and an additional change of the testing room would affect the open arm time and other behaviours on the EPM. In two experiments, drug naive Wistar rats were exposed to the EPM on trial 1, and treated intraperitoneally with either vehicle or midazolam (0.25 mg/kg 30 min before trial 2. Then, trial 2 (28 days after trial 1 was carried out in either the same testing room (Exp. 1 or a second unfamiliar room (Exp. 2.Twenty-eight days after trial 1 the open arm time of the rats in the vehicle treated control rats of both experimental groups was comparable to that of the first trial, independent of the testing room. Most importantly, we found that the treatment with the benzodiazepine midazolam had a significantly anxiolytic-like (i.e. increase of open arm time effect in trial 2 only when conducted in the previously unfamiliar testing room (Exp. 2. We suggest that in order to reliably re-test the EPM and to prevent confounding effects due to the OTT, an inter-trial interval of 28 days and a change in testing rooms reinstates anxiolytic-like actions of benzodiazepines

  5. Comparison report of open calculations for ATLAS Domestic Standard Problem (DSP 02)

    International Nuclear Information System (INIS)

    Choi, Ki Yong; Kim, Y. S.; Kang, K. H.; Cho, S.; Park, H. S.; Choi, N. H.; Kim, B. D.; Min, K. H.; Park, J. K.; Chun, H. G.; Yu, Xin Guo; Kim, H. T.; Song, C. H.; Sim, S. K.; Jeon, S. S.; Kim, S. Y.; Kang, D. G.; Choi, T. S.; Kim, Y. M.; Lim, S. G.; Kim, H. S.; Kang, D. H.; Lee, G. H.; Jang, M. J.

    2012-09-01

    KAERI (Korea Atomic Energy Research Institute) has been operating an integral effect test facility, the Advanced Thermal Hydraulic Test Loop for Accident Simulation (ATLAS) for transient and accident simulations of advanced pressurized water reactors (PWRs). By using the ATLAS, a high quality integral effect test database has been established for major design basis accidents of the APR1400. A Domestic Standard Problem (DSP) exercise using the ATLAS database was promoted in order to transfer the database to domestic nuclear industries and to contribute to improving safety analysis methodology for PWRs. This 2nd ATLAS DSP exercise was led by KAERI in collaboration with KINS since the successful completion of the 1st ATLAS DSP in 2009. This exercise aims at effective utilization of integral effect database obtained from the ATLAS, establishment of cooperation framework among the domestic nuclear industry, better understanding of thermal hydraulic phenomena, and investigation of the possible limitation of the existing best estimate safety analysis codes. A small break loss of coolant accident of 6 inch break at the cold leg was determined as a target scenario by considering its technical importance and by incorporating with interests from participants. Twelve domestic organizations joined this DSP 02 exercise. Finally, eleven out of the joined organizations submitted their calculation results, including universities, government, and nuclear industries. This DSP exercise was performed in an open calculation environment where the integral effect test data was open to participants prior to code calculations. This report includes all information of the 2nd ATLAS DSP (DSP 02) exercise as well as comparison results between the calculations and the experimental data

  6. Outcomes of Domestic Standard Problem-03 : Scaling Capability of Facility Data

    Energy Technology Data Exchange (ETDEWEB)

    Park, Yusun; Youn, Bumsu; Lee, Seung-won; Kim, Won-tae; Kang, Kyoung-ho; Choi, Ki-yong [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-10-15

    The Domestic Standard Problem (DSP) previous two DSPs provided good research opportunities to many nuclear organizations to understand the capability of the current system-scale safety analysis codes and to find a way for further code development area. Thus, the third DSP program was launched in the 2nd half of the year 2012. As the third DSP exercise (DSP-03), a double-ended guillotine break of the main steam line at an 8% power without loss of off-site power (LOOP) was decided a target scenario. Seventeen domestic organizations joined this DSP exercise. This DSP exercise was performed in an open calculation environment similar to the previous ones. In the present DSP-03, taking into accounts the different levels of code experiences and expertise, three sub-topics were suggested by operating agency. Among them, the investigation on scaling capability of facility data which was the topic of Group A will be discussed in this paper. Agreed participants should perform two calculations with the ATLAS model and the APR1400 model. By comparing major and detailed local parameters from both calculation models, scaling capability of the facility data was investigated. The 38.6 mm MSLB in ATLAS test facility was calculated using SPACE and MARS-KS code. To analyze the effect of scaling on the system behavior, MSLB in APR-1400 was also simulated in this study and following results were obtained. - The code predicted appropriately the overall MSLB experimental data obtained from ATLAS test facility. - The break flow calculated by code was lower than that of experimental data. - And the difference between calculated value and measured value was attributed to the measurement of mass from break flow. - The temperatures of core inlet and outlet of ATLAS test facility were predicted lower than those of experimental data.

  7. Comparison between the triglycerides standardization of routine methods used in Japan and the chromotropic acid reference measurement procedure used by the CDC Lipid Standardization Programme.

    Science.gov (United States)

    Nakamura, Masakazu; Iso, Hiroyasu; Kitamura, Akihiko; Imano, Hironori; Noda, Hiroyuki; Kiyama, Masahiko; Sato, Shinichi; Yamagishi, Kazumasa; Nishimura, Kunihiro; Nakai, Michikazu; Vesper, Hubert W; Teramoto, Tamio; Miyamoto, Yoshihiro

    2016-11-01

    Background The US Centers for Disease Control and Prevention ensured adequate performance of the routine triglycerides methods used in Japan by a chromotropic acid reference measurement procedure used by the Centers for Disease Control and Prevention lipid standardization programme as a reference point. We examined standardized data to clarify the performance of routine triglycerides methods. Methods The two routine triglycerides methods were the fluorometric method of Kessler and Lederer and the enzymatic method. The methods were standardized using 495 Centers for Disease Control and Prevention reference pools with 98 different concentrations ranging between 0.37 and 5.15 mmol/L in 141 survey runs. The triglycerides criteria for laboratories which perform triglycerides analyses are used: accuracy, as bias ≤5% from the Centers for Disease Control and Prevention reference value and precision, as measured by CV, ≤5%. Results The correlation of the bias of both methods to the Centers for Disease Control and Prevention reference method was: y (%bias) = 0.516 × (Centers for Disease Control and Prevention reference value) -1.292 ( n = 495, R 2  = 0.018). Triglycerides bias at medical decision points of 1.13, 1.69 and 2.26 mmol/L was -0.71%, -0.42% and -0.13%, respectively. For the combined precision, the equation y (CV) = -0.398 × (triglycerides value) + 1.797 ( n = 495, R 2  = 0.081) was used. Precision was 1.35%, 1.12% and 0.90%, respectively. It was shown that triglycerides measurements at Osaka were stable for 36 years. Conclusions The epidemiologic laboratory in Japan met acceptable accuracy goals for 88.7% of all samples, and met acceptable precision goals for 97.8% of all samples measured through the Centers for Disease Control and Prevention lipid standardization programme and demonstrated stable results for an extended period of time.

  8. A Guide for Developing Standard Operating Job Procedures for the Tertiary Chemical Treatment - Lime Precipitation Process Wastewater Treatment Facility. SOJP No. 6.

    Science.gov (United States)

    Petrasek, Al, Jr.

    This guide describes the standard operating job procedures for the tertiary chemical treatment - lime precipitation process of wastewater treatment plants. Step-by-step instructions are given for pre-start up, start-up, continuous operation, and shut-down procedures. In addition, some theoretical material is presented along with some relevant…

  9. Standard Operating Procedure for the Grinding and Extraction of Lead in Paint using Nitric Acid and a Rotor/Stator System Powered by a High Speed Motor

    Science.gov (United States)

    This Standard Operating Procedure (SOP) describes a new, rapid, and relatively inexpensive one step procedure which grinds the paint samples removed from the substrate and simultaneously quantitatively extracts the Pb from the paint in only one step in preparation for quantitativ...

  10. Removal of foot-and-mouth disease virus infectivity in salted natural casings by minor adaptation of standardized industrial procedures.

    Science.gov (United States)

    Wijnker, J J; Haas, B; Berends, B R

    2007-04-10

    Intestines are used for the production of natural casings as edible sausage containers. Derived from animals (pigs and sheep) experimentally infected with FMDV (initial dosage 10(7.3) PFU/ml, strain O(1Kaufbeuren)), these natural casings were treated with sodium chloride or a phosphate salts/sodium chloride mixture and the residual FMDV titres measured. After storage at about 20 degrees C, no remaining infectivity was found after either treatment, whereas casings stored at 4 degrees C still contained infectivity. Storage of salted casings at about 20 degrees C for 30 days is already part of the Standard Operating Procedures (included in HACCP) of the international casing industry and can therefore be considered as a protective measure for the international trade in natural casings.

  11. Standardization of digestion procedure for the determination of heavy metals in biological materials by atomic absorption spectrometry

    International Nuclear Information System (INIS)

    Khalid, N.; Chaudhri, S.A.

    1999-01-01

    Proper decomposition of the sample is one of the basic requirements of the atomic absorption spectroscopic analysis. In the present studies, heavy metals (Cu, Fe, Mn and Zn) were determined in biological samples by designating them in a mixture of nitric acid and perchloric acid. The quantification was made with atomic absorption spectrometry using an air-acetylene flame. The reliability of the procedure used was checked by analysing standard reference materials from NBS and IAEA, such as Rice flour (NBS-SRM-1568), Horse Kidney (IAEA H-8), Mixed Human diet(IAEA H-9), Copepod (IAEA MA-A-1) and fish flesh (IAEA MA-A-2) under identical conditions. A good agreement was observed between determined and the certified values reported by NBS and IAEA. (author)

  12. Design of standard operating procedure production proceses (case study on the home industry Bedugul Baturiti Tabanan Bali)

    Science.gov (United States)

    Kasiani; Suhantono, Djoko; Mirah Kencanawati, AAA

    2018-01-01

    Candikuning is part of the district of Baturiti, tourism village, better known by the name of Bedugul. No less interesting is the variety of chips produced by two partner groups as a souvenir after the tour, such as Chips: Spinach; beans; Tempeh. The purpose of this research were to design a Standard Operating Procedure (SOP): Production Processes on the Home Industry Bedugul Baturiti Tabanan Bali. The data technic collected use: observation; Documentation; and then interview to collect information. The data analysis technic done by using the Miles & Huberman. Result this research that the draft SOP: Production Processes Chips (Menu). The conclusion in this research SOP Production Processes use with flowchart and description on the Home Industry Bedugul Baturiti Tabanan Bali.

  13. A Practical and Robust Execution Time-Frame Procedure for the Multi-Mode Resource-Constrained Project Scheduling Problem with Minimal and Maximal Time Lags

    Directory of Open Access Journals (Sweden)

    Angela Hsiang-Ling Chen

    2016-09-01

    Full Text Available Modeling and optimizing organizational processes, such as the one represented by the Resource-Constrained Project Scheduling Problem (RCPSP, improve outcomes. Based on assumptions and simplification, this model tackles the allocation of resources so that organizations can continue to generate profits and reinvest in future growth. Nonetheless, despite all of the research dedicated to solving the RCPSP and its multi-mode variations, there is no standardized procedure that can guide project management practitioners in their scheduling tasks. This is mainly because many of the proposed approaches are either based on unrealistic/oversimplified scenarios or they propose solution procedures not easily applicable or even feasible in real-life situations. In this study, we solve a more true-to-life and complex model, Multimode RCPSP with minimal and maximal time lags (MRCPSP/max. The complexity of the model solved is presented, and the practicality of the proposed approach is justified depending on only information that is available for every project regardless of its industrial context. The results confirm that it is possible to determine a robust makespan and to calculate an execution time-frame with gaps lower than 11% between their lower and upper bounds. In addition, in many instances, the solved lower bound obtained was equal to the best-known optimum.

  14. Validation of standard operating procedures in a multicenter retrospective study to identify -omics biomarkers for chronic low back pain.

    Directory of Open Access Journals (Sweden)

    Concetta Dagostino

    Full Text Available Chronic low back pain (CLBP is one of the most common medical conditions, ranking as the greatest contributor to global disability and accounting for huge societal costs based on the Global Burden of Disease 2010 study. Large genetic and -omics studies provide a promising avenue for the screening, development and validation of biomarkers useful for personalized diagnosis and treatment (precision medicine. Multicentre studies are needed for such an effort, and a standardized and homogeneous approach is vital for recruitment of large numbers of participants among different centres (clinical and laboratories to obtain robust and reproducible results. To date, no validated standard operating procedures (SOPs for genetic/-omics studies in chronic pain have been developed. In this study, we validated an SOP model that will be used in the multicentre (5 centres retrospective "PainOmics" study, funded by the European Community in the 7th Framework Programme, which aims to develop new biomarkers for CLBP through three different -omics approaches: genomics, glycomics and activomics. The SOPs describe the specific procedures for (1 blood collection, (2 sample processing and storage, (3 shipping details and (4 cross-check testing and validation before assays that all the centres involved in the study have to follow. Multivariate analysis revealed the absolute specificity and homogeneity of the samples collected by the five centres for all genetics, glycomics and activomics analyses. The SOPs used in our multicenter study have been validated. Hence, they could represent an innovative tool for the correct management and collection of reliable samples in other large-omics-based multicenter studies.

  15. Standard operating procedures for pre-analytical handling of blood and urine for metabolomic studies and biobanks.

    Science.gov (United States)

    Bernini, Patrizia; Bertini, Ivano; Luchinat, Claudio; Nincheri, Paola; Staderini, Samuele; Turano, Paola

    2011-04-01

    (1)H NMR metabolic profiling of urine, serum and plasma has been used to monitor the impact of the pre-analytical steps on the sample quality and stability in order to propose standard operating procedures (SOPs) for deposition in biobanks. We analyzed the quality of serum and plasma samples as a function of the elapsed time (t = 0-4 h) between blood collection and processing and of the time from processing to freezing (up to 24 h). The stability of the urine metabolic profile over time (up to 24 h) at various storage temperatures was monitored as a function of the different pre-analytical treatments like pre-storage centrifugation, filtration, and addition of the bacteriostatic preservative sodium azide. Appreciable changes in the profiles, reflecting changes in the concentration of a number of metabolites, were detected and discussed in terms of chemical and enzymatic reactions for both blood and urine samples. Appropriate procedures for blood derivatives collection and urine preservation/storage that allow maintaining as much as possible the original metabolic profile of the fresh samples emerge, and are proposed as SOPs for biobanking.

  16. Standard operating procedures for pre-analytical handling of blood and urine for metabolomic studies and biobanks

    International Nuclear Information System (INIS)

    Bernini, Patrizia; Bertini, Ivano; Luchinat, Claudio; Nincheri, Paola; Staderini, Samuele; Turano, Paola

    2011-01-01

    1 H NMR metabolic profiling of urine, serum and plasma has been used to monitor the impact of the pre-analytical steps on the sample quality and stability in order to propose standard operating procedures (SOPs) for deposition in biobanks. We analyzed the quality of serum and plasma samples as a function of the elapsed time (t = 0−4 h) between blood collection and processing and of the time from processing to freezing (up to 24 h). The stability of the urine metabolic profile over time (up to 24 h) at various storage temperatures was monitored as a function of the different pre-analytical treatments like pre-storage centrifugation, filtration, and addition of the bacteriostatic preservative sodium azide. Appreciable changes in the profiles, reflecting changes in the concentration of a number of metabolites, were detected and discussed in terms of chemical and enzymatic reactions for both blood and urine samples. Appropriate procedures for blood derivatives collection and urine preservation/storage that allow maintaining as much as possible the original metabolic profile of the fresh samples emerge, and are proposed as SOPs for biobanking.

  17. Standard operating procedures for pre-analytical handling of blood and urine for metabolomic studies and biobanks

    Energy Technology Data Exchange (ETDEWEB)

    Bernini, Patrizia; Bertini, Ivano, E-mail: bertini@cerm.unifi.it; Luchinat, Claudio [University of Florence, Magnetic Resonance Center (CERM) (Italy); Nincheri, Paola; Staderini, Samuele [FiorGen Foundation (Italy); Turano, Paola [University of Florence, Magnetic Resonance Center (CERM) (Italy)

    2011-04-15

    {sup 1}H NMR metabolic profiling of urine, serum and plasma has been used to monitor the impact of the pre-analytical steps on the sample quality and stability in order to propose standard operating procedures (SOPs) for deposition in biobanks. We analyzed the quality of serum and plasma samples as a function of the elapsed time (t = 0-4 h) between blood collection and processing and of the time from processing to freezing (up to 24 h). The stability of the urine metabolic profile over time (up to 24 h) at various storage temperatures was monitored as a function of the different pre-analytical treatments like pre-storage centrifugation, filtration, and addition of the bacteriostatic preservative sodium azide. Appreciable changes in the profiles, reflecting changes in the concentration of a number of metabolites, were detected and discussed in terms of chemical and enzymatic reactions for both blood and urine samples. Appropriate procedures for blood derivatives collection and urine preservation/storage that allow maintaining as much as possible the original metabolic profile of the fresh samples emerge, and are proposed as SOPs for biobanking.

  18. Standard Operating Procedure

    National Research Council Canada - National Science Library

    1997-01-01

    ...) plastic collection bag system. Red blood cell concentrates stored at 4 C in the 800 ml primary plastic collection bag can be biochemically modified to increase the red cell 2,3 DPG and ATP levels...

  19. Comparison and Interpretation Report of the OECD International Standard Problem No. 45 - Exercise (QUENCH-06)

    International Nuclear Information System (INIS)

    Hering, W.; Homann, Ch.; Lamy, J.S.; Miassoedov, A.; Schanz, G.; Sepold, L.; Steinbrueck, M.

    2002-10-01

    The International Standard Problem (ISP) No. 45 is part of the overall ISP program of the OECD/NEA and is dedicated to the behavior of heat-up and delayed reflood of fuel elements in nuclear reactors during a hypothetical accident. ISP-45 is related to the out-of-pile bundle quench experiment QUENCH-06, performed at Forschungszentrum Karlsruhe (FZK), Germany, on December 13, 2000. Special attention was paid to hydrogen production. To assess the ability of severe accident codes to simulate processes during core heat-up and reflood at temperatures above 2000 K, the behavior of the bundle during the whole experiment should be calculated on the basis of the necessary experimental initial and boundary conditions, but without knowing further experimental details. In this so-called blind phase 21 participants from 15 nations contributed with 8 different code systems (ATHLET-CD, ICARE/CATHARE, IMPACT/SAMPSON, GENFLO, MAAP, MELCOR, SCDAPSIM, SCDAP-3D). Additionally, posttest calculations using the in-house version SCDAP/RELAP5 mod3.2.irs are used for comparison. After the end of the blind phase all measured data were made available and the participants were invited to deliver a second calculation, where this knowledge could be used (so-called open phase). In this report, results of the blind calculations are presented, analyzed, and compared to experimental data. During heat-up most results do not deviate significantly from one another, except as a consequence of some obvious user errors, so that a definition of a mainstream is justified. For the quench phase the lack of adequate hydraulic modeling becomes obvious: some participants could not match the observed cool-down rates, others had to use very fine meshes to compensate code deficiencies. To overcome this insufficiency some newly developed reflood models were used in MAAP and MELCOR. In QUENCH-06, oxide layers were thick enough to protect the cladding from melting and failure below 2200 K, so that no massive hydrogen

  20. Examination of the potential problems resulting from the settling of U5 procedure (filtered venting of the containment) on French PWR'S

    International Nuclear Information System (INIS)

    L'Homme, A.; Serviere, G.

    1988-06-01

    A filtered venting system of the containment including a sand bed (U5 procedure) is now settled on french PWR's. In this paper, one reviews the problems which are raised, concerning either the efficiency of the system or the safety of the nuclear unit. Two types of situations are examined: design situations, for which the U5 procedure is not used, and hypothetical accidental situations, for which the U5 procedure could be used

  1. International Standard Problems and Small Break Loss-of-Coolant Accident (SBLOCA

    Directory of Open Access Journals (Sweden)

    N. Aksan

    2008-01-01

    Full Text Available Best-estimate thermal-hydraulic system codes are widely used to perform safety and licensing analyses of nuclear power plants and also used in the design of advance reactors. Evaluation of the capabilities and the performance of these codes can be accomplished by comparing the code predictions with measured experimental data obtained on different test facilities. OECD/NEA Committee on the Safety of Nuclear Installations (CSNI has promoted, over the last twenty-nine years, some forty-eight international standard problems (ISPs. These ISPs were performed in different fields as in-vessel thermal-hydraulic behaviour, fuel behaviour under accident conditions, fission product release and transport, core/concrete interactions, hydrogen distribution and mixing, containment thermal-hydraulic behaviour. 80% of these ISPs were related to the working domain of principal working group no.2 on coolant system behaviour (PWG2 and were one of the major PWG2 activities for many years. A global review and synthesis on the contribution that ISPs have made to address nuclear reactor safety issues was initiated by CSNI-PWG2 and an overview on the subject of small break LOCA ISPs is given in this paper based on a report prepared by a writing group. In addition, the relevance of small break LOCA in a PWR with relation to nuclear reactor safety and the reorientation of the reactor safety program after TMI-2 accident are shortly summarized. The experiments in four integral test facilities, LOBI, SPES, BETHSY, ROSA IV/LSTF and the recorded data during a steam generator tube rupture transient in the DOEL-2 PWR (Belgium were the basis of the five small break LOCA related ISP exercises, which deal with the phenomenon typical of small break LOCAs in Western design PWRs. Some lessons learned from these small break LOCA ISPs are identified in relation to code deficiencies and capabilities, progress in the code capabilities, possibility of scaling, and various additional aspects

  2. International Standard Problems and Small Break Loss-Of-Coolant Accident (SBLOCA)

    International Nuclear Information System (INIS)

    Aksan, N.

    2008-01-01

    Best-estimate thermalhydraulic system codes are widely used to perform safety and licensing analyses of nuclear power plants and also used in the design of advance reactors. Evaluation of the capabilities and the performance of these codes can be accomplished by comparing the code predictions with measured experimental data obtained on different test facilities. In this respect, parallel to other national and international programs, OECD/Nea (OECD Nuclear Energy Agency) Committee on the Safety of Nuclear Installations (CSNI) has promoted, over the last twenty-nine years some forty-eight International Standard Problems (ISPs). These ISPs were performed in different fields as in-vessel thermalhydraulic behaviour, fuel behaviour under accident conditions, fission product release and transport, core/concrete interactions, hydrogen distribution and mixing, containment thermalhydraulic behaviour. 80% of these ISPs were related to the working domain of Principal Working Group no. 2 on Coolant System Behaviour (PWG2). The ISPs have been one of the major PWG2 activities for many years. The individual ISP comparison reports include the analysis and conclusions of the specific ISP exercises. A global review and synthesis on the contribution that ISPs have made to address nuclear reactor safety issues was initiated by CSNI-PWG2 and an overview on the subject of small break LOCA ISP's is given in this paper based on a report prepared by a CSNI-PWG2 writing group. In addition, the relevance of small break LOCA in a PWR with relation to nuclear reactor safety and the reorientation of the reactor safety program after TMI-2 accident, specifically small break LOCA, are shortly summarized. Five small break LOCA related ISP's are considered, since these were used for the assessment of the advanced best-estimate codes. The considered ISP's deal with the phenomenon typical of small break LOCAs in Western design PWRs. The experiments in four integral test facilities, LOBI, SPES, BETHSY

  3. Thematic network for a Phebus FPT1 international standard problem (THENPHEBISP)

    International Nuclear Information System (INIS)

    Clement, B.; Haste, T.; Krausmann, E.; Dickinson, S.; Gyenes, G.; Duspiva, J.; Rosa, F. de; Paci, S.; Martin-Fuertes, F.; Scholytssek, W.; Allelein, H.-J.; Guentay, S.; Arien, B.; Marguet, S.; Leskovar, M.; Sartmadjiev, A.

    2005-01-01

    The THENPHEBISP 2-year thematic network started in December 2001, and was concerned with OECD/CSNI International Standard Problem 46, itself based on the Phebus FPT1 core degradation/source term experiment. The aim was to assess the capability of computer codes to model in an integrated way the physical processes taking place during a severe accident in a pressurised water reactor, from the initial stages of core degradation, the fission product transport through the primary circuit and the behaviour of the released fission products in the containment. ISP-46, coordinated by IRSN/DRS Cadarache, attracted 33 participating organisations, from 23 countries and international bodies, who submitted 47 base case calculations and 21 best-estimate calculations, using 15 different codes. The thermal behaviour of the fuel bundle and the hydrogen production were generally well captured, and good agreement for the core final state could be obtained with a suitable choice of bulk fuel relocation temperature, however this is unlikely to be representative of all plant studies so sensitivity calculations are needed with the modelling in its current state. Total volatile fission product release was simulated, but its kinetics, and the overall modelling of semi-volatile, low-volatile and structural material release (Ag/In/Cd, Sn) needs improvement. Overall retention in the circuit is well predicted, but calculations underestimate deposits in the upper plenum and overestimate those in the steam generator, also the volatility of some elements could be better predicted. Containment thermal hydraulics and depletion rate of aerosols are well calculated, but with difficulties related to partition amongst the deposition mechanisms. Calculation of iodine chemistry in the containment turned out to be more difficult. Its quality strongly depends of the calculation of release and transport in the integral codes. The major difficulties are related to the existence of gaseous iodine in the

  4. Input data preparation and simulation of the second standard problem of IAEA using the Trac/PF1 code

    International Nuclear Information System (INIS)

    Madeira, A.A.; Pontedeiro, A.C.; Silva Galetti, M.R. da; Borges, R.C.

    1989-10-01

    The second Standard Problem sponsored by IAEA consists in the simulation of a small LOCA located in the downcomer of a PMK-NVH integral test facility, which models WWER/440 type reactor. This report presents input data preparation and comparison between TRAC-PF1 results and experimental measurements. (author) [pt

  5. Measurement standards and the general problem of reference points in chemical analysis

    International Nuclear Information System (INIS)

    Richter, W.; Dube, G.

    2002-01-01

    Besides the measurement standards available in general metrology in the form of the realisations of the units of measurement, measurement standards of chemical composition are needed for the vast field of chemical measurement (measurements of the chemical composition), because it is the main aim of such measurements to quantify non-isolated substances, often in complicated matrices, to which the 'classical' measurement standards and their lower- level derivatives are not directly applicable. At present, material artefacts as well as standard measurement devices serve as chemical measurement standards. These are measurement standards in the full metrological sense only, however, if they are firmly linked to the SI unit in which the composition represented by the standard is expressed. This requirement has the consequence that only a very restricted number of really reliable chemical measurement standards exist at present. Since it is very difficult and time consuming to increase this number substantially and, on the other hand, reliable reference points are increasingly needed for all kinds of chemical measurements, primary methods of measurement and high-level reference measurements will play an increasingly important role for the establishment of worldwide comparability and hence mutual acceptance of chemical measurement results. (author)

  6. Review of cause-based decision tree approach for the development of domestic standard human reliability analysis procedure in low power/shutdown operation probabilistic safety assessment

    International Nuclear Information System (INIS)

    Kang, D. I.; Jung, W. D.

    2003-01-01

    We review the Cause-Based Decision Tree (CBDT) approach to decide whether we incorporate it or not for the development of domestic standard Human Reliability Analysis (HRA) procedure in low power/shutdown operation Probabilistic Safety Assessment (PSA). In this paper, we introduce the cause based decision tree approach, quantify human errors using it, and identify merits and demerits of it in comparision with previously used THERP. The review results show that it is difficult to incorporate the CBDT method for the development of domestic standard HRA procedure in low power/shutdown PSA because the CBDT method need for the subjective judgment of HRA analyst like as THERP. However, it is expected that the incorporation of the CBDT method into the development of domestic standard HRA procedure only for the comparision of quantitative HRA results will relieve the burden of development of detailed HRA procedure and will help maintain consistent quantitative HRA results

  7. Comparison of Test Procedures and Energy Efficiency Criteria in Selected International Standards & Labeling Programs for Copy Machines, External Power Supplies, LED Displays, Residential Gas Cooktops and Televisions

    Energy Technology Data Exchange (ETDEWEB)

    Zheng, Nina [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Zhou, Nan [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Fridley, David [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2012-03-01

    This report presents a technical review of international minimum energy performance standards (MEPS), voluntary and mandatory energy efficiency labels and test procedures for five products being considered for new or revised MEPS in China: copy machines, external power supply, LED displays, residential gas cooktops and flat-screen televisions. For each product, an overview of the scope of existing international standards and labeling programs, energy values and energy performance metrics and description and detailed summary table of criteria and procedures in major test standards are presented.

  8. Planning Model of Physics Learning In Senior High School To Develop Problem Solving Creativity Based On National Standard Of Education

    Science.gov (United States)

    Putra, A.; Masril, M.; Yurnetti, Y.

    2018-04-01

    One of the causes of low achievement of student’s competence in physics learning in high school is the process which they have not been able to develop student’s creativity in problem solving. This is shown that the teacher’s learning plan is not accordance with the National Eduction Standard. This study aims to produce a reconstruction model of physics learning that fullfil the competency standards, content standards, and assessment standards in accordance with applicable curriculum standards. The development process follows: Needs analysis, product design, product development, implementation, and product evaluation. The research process involves 2 peers judgment, 4 experts judgment and two study groups of high school students in Padang. The data obtained, in the form of qualitative and quantitative data that collected through documentation, observation, questionnaires, and tests. The result of this research up to the product development stage that obtained the physics learning plan model that meets the validity of the content and the validity of the construction in terms of the fulfillment of Basic Competence, Content Standards, Process Standards and Assessment Standards.

  9. Microwave-assisted versus conventional decomposition procedures applied to a ceramic potsherd standard reference material by inductively coupled plasma atomic emission spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Papadopoulou, D.N.; Zachariadis, G.A.; Anthemidis, A.N.; Tsirliganis, N.C.; Stratis, J.A

    2004-03-03

    Inductively coupled plasma atomic emission spectrometry (ICP-AES) is a powerful, sensitive analytical technique with numerous applications in chemical characterization including that of ancient pottery, mainly due to its multi-element character, and the relatively short time required for the analysis. A critical step in characterization studies of ancient pottery is the selection of a suitable decomposition procedure for the ceramic matrix. The current work presents the results of a comparative study of six decomposition procedures applied on a standard ceramic potsherd reference material, SARM 69. The investigated decomposition procedures included three microwave-assisted decomposition procedures, one wet decomposition (WD) procedure by conventional heating, one combined microwave-assisted and conventional heating WD procedure, and one fusion procedure. Chemical analysis was carried out by ICP-AES. Five major (Si, Al, Fe, Ca, Mg), three minor (Mn, Ba, Ti) and two trace (Cu, Co) elements were determined and compared with their certified values. Quantitation was performed at two different spectral lines for each element and multi-element matrix-matched calibration standards were used. The recovery values for the six decomposition procedures ranged between 75 and 110% with a few notable exceptions. Data were processed statistically in order to evaluate the investigated decomposition procedures in terms of recovery, accuracy and precision, and eventually select the most appropriate one for ancient pottery analysis.

  10. Problems of introduction of international standards of conscientious state financial management in Ukrainian practice

    OpenAIRE

    Anhelina, I.

    2014-01-01

    The m aintenance of the INTOSAI GOV standardssystem, which show by itself guidance from a conscientious state financial management in the field of internal control and standards of record-keeping, is generalized. The directions of the use of risk and control model COSO are determinated for the financial management of state sector in part of authentication of sources of risk, aims and duties of organization. The measures are worked out on introduction of standards of INTOSAI GOVand models of C...

  11. Use of a pressure sensing sheath: comparison with standard means of blood pressure monitoring in catheterization procedures.

    Science.gov (United States)

    Purdy, Phillip D; South, Charles; Klucznik, Richard P; Liu, Kenneth C; Novakovic, Robin L; Puri, Ajit S; Pride, G Lee; Aagaard-Kienitz, Beverly; Ray, Abishek; Elliott, Alan C

    2017-08-01

    Monitoring of blood pressure (BP) during procedures is variable, depending on multiple factors. Common methods include sphygmomanometer (BP cuff), separate radial artery catheterization, and side port monitoring of an indwelling sheath. Each means of monitoring has disadvantages, including time consumption, added risk, and signal dampening due to multiple factors. We sought an alternative approach to monitoring during procedures in the catheterization laboratory. A new technology involving a 330 µm fiberoptic sensor embedded in the wall of a sheath structure was tested against both radial artery catheter and sphygmomanometer readings obtained simultaneous with readings recorded from the pressure sensing system (PSS). Correlations and Bland-Altman analysis were used to determine whether use of the PSS could substitute for these standard techniques. The results indicated highly significant correlations in systolic, diastolic, and mean arterial pressures (MAP) when compared against radial artery catheterization (p<0.0001), and MAP means differed by <4%. Bland-Altman analysis of the data suggested that the sheath measurements can replace a separate radial artery catheter. While less striking, significant correlations were seen when PSS readings were compared against BP cuff readings. The PSS has competitive functionality to that seen with a dedicated radial artery catheter for BP monitoring and is available immediately on sheath insertion without the added risk of radial catheterization. The sensor is structurally separated from the primary sheath lumen and readings are unaffected by device introduction through the primary lumen. Time delays and potential complications from radial artery catheterization are avoided. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

  12. Calibration of photon and beta ray sources used in brachytherapy. Guidelines on standardized procedures at Secondary Standards Dosimetry Laboratories (SSDLs) and hospitals

    International Nuclear Information System (INIS)

    2002-03-01

    It has generally been recognized that international harmonization in radiotherapy dosimetry is essential. Consequently, the IAEA has given much effort to this, for example by publishing a number of reports in the Technical Reports Series (TRS) for external beam dosimetry, most notably TRS-277 and more recently TRS-398. Both of these reports describe in detail the steps to be taken for absorbed dose determination in water and they are often referred to as 'dosimetry protocols'. Similar to TRS-277, it is expected that TRS-398 will be adopted or used as a model by a large number of countries as their national protocol. In 1996, the IAEA established a calibration service for low dose rate (LDR) 137 Cs brachytherapy sources, which is the most widely used source for treatment of gynecological cancer. To further enhance harmonization in brachytherapy dosimetry, the IAEA published in 1999 IAEA-TECDOC-1079 entitled 'Calibration of Brachytherapy Sources. Guidelines on Standardized Procedures for the Calibration of Brachytherapy Sources at Secondary Standard Dosimetry Laboratories (SSDLs) and Hospitals'. The report was well received and was distributed in a large number of copies to the members of the IAEA/WHO network of SSDLs and to medical physicists working with brachytherapy. The present report is an update of the aforementioned TECDOC. Whereas TECDOC-1079 described methods for calibrating brachytherapy sources with photon energies at or above those of 192 Ir, the current report has a wider scope in that it deals with standardization of calibration of all the most commonly used brachytherapy sources, including both photon and beta emitting sources. The latter sources have been in use for a few decades already, but their calibration methods have been unclear. Methods are also described for calibrating sources used in the rapidly growing field of cardiovascular angioplasty. In this application, irradiation of the vessel wall is done in an attempt to prevent restenosis after

  13. A comparative study on assessment procedures and metric properties of two scoring systems of the Coma Recovery Scale-Revised items: standard and modified scores.

    Science.gov (United States)

    Sattin, Davide; Lovaglio, Piergiorgio; Brenna, Greta; Covelli, Venusia; Rossi Sebastiano, Davide; Duran, Dunja; Minati, Ludovico; Giovannetti, Ambra Mara; Rosazza, Cristina; Bersano, Anna; Nigri, Anna; Ferraro, Stefania; Leonardi, Matilde

    2017-09-01

    The study compared the metric characteristics (discriminant capacity and factorial structure) of two different methods for scoring the items of the Coma Recovery Scale-Revised and it analysed scale scores collected using the standard assessment procedure and a new proposed method. Cross sectional design/methodological study. Inpatient, neurological unit. A total of 153 patients with disorders of consciousness were consecutively enrolled between 2011 and 2013. All patients were assessed with the Coma Recovery Scale-Revised using standard (rater 1) and inverted (rater 2) procedures. Coma Recovery Scale-Revised score, number of cognitive and reflex behaviours and diagnosis. Regarding patient assessment, rater 1 using standard and rater 2 using inverted procedures obtained the same best scores for each subscale of the Coma Recovery Scale-Revised for all patients, so no clinical (and statistical) difference was found between the two procedures. In 11 patients (7.7%), rater 2 noted that some Coma Recovery Scale-Revised codified behavioural responses were not found during assessment, although higher response categories were present. A total of 51 (36%) patients presented the same Coma Recovery Scale-Revised scores of 7 or 8 using a standard score, whereas no overlap was found using the modified score. Unidimensionality was confirmed for both score systems. The Coma Recovery Scale Modified Score showed a higher discriminant capacity than the standard score and a monofactorial structure was also supported. The inverted assessment procedure could be a useful evaluation method for the assessment of patients with disorder of consciousness diagnosis.

  14. Towards a Standard-based Domain-specific Platform to Solve Machine Learning-based Problems

    Directory of Open Access Journals (Sweden)

    Vicente García-Díaz

    2015-12-01

    Full Text Available Machine learning is one of the most important subfields of computer science and can be used to solve a variety of interesting artificial intelligence problems. There are different languages, framework and tools to define the data needed to solve machine learning-based problems. However, there is a great number of very diverse alternatives which makes it difficult the intercommunication, portability and re-usability of the definitions, designs or algorithms that any developer may create. In this paper, we take the first step towards a language and a development environment independent of the underlying technologies, allowing developers to design solutions to solve machine learning-based problems in a simple and fast way, automatically generating code for other technologies. That can be considered a transparent bridge among current technologies. We rely on Model-Driven Engineering approach, focusing on the creation of models to abstract the definition of artifacts from the underlying technologies.

  15. Thermohydraulic analysis of the IAEA standard problem test on the PMK-NHV facility; Termohidraulicna analiza standardnega problem MAAE na poskusni napravi PMK-NHV

    Energy Technology Data Exchange (ETDEWEB)

    Stritar, A [Institut Jozef Stefan, Ljubljana (Yugoslavia)

    1987-07-01

    International Atomic Energy Agency (IAEA) has supported a standard test problem simulating small break loss of coolant accident on the test facility PMH-NHV in Budapest. The present pretest analysis of that transient was done using the computer code RELAP4/MOD6. The results were compared to the measurements data and to data of 19 other laboratories around the world that have performed the same analysis. The correspondence of the results to the measured data is reasonable. There are bigger discrepancies, which in turn influence other variables. (author)

  16. Development of Learning Models Based on Problem Solving and Meaningful Learning Standards by Expert Validity for Animal Development Course

    Science.gov (United States)

    Lufri, L.; Fitri, R.; Yogica, R.

    2018-04-01

    The purpose of this study is to produce a learning model based on problem solving and meaningful learning standards by expert assessment or validation for the course of Animal Development. This research is a development research that produce the product in the form of learning model, which consist of sub product, namely: the syntax of learning model and student worksheets. All of these products are standardized through expert validation. The research data is the level of validity of all sub products obtained using questionnaire, filled by validators from various field of expertise (field of study, learning strategy, Bahasa). Data were analysed using descriptive statistics. The result of the research shows that the problem solving and meaningful learning model has been produced. Sub products declared appropriate by expert include the syntax of learning model and student worksheet.

  17. Final Rule for Control of Air Pollution from Aircraft and Aircraft Engines: Emission Standards and Test Procedures

    Science.gov (United States)

    EPA is amending the existing emission standards for oxides of nitrogen (NOx) for new commercial aircraft engines. These standards are equivalent to the NOx emission standards of the United Nations International Civil Aviation Organization (ICAO).

  18. Direct Final Rule for Control of Air Pollution From Aircraft and Aircraft Engines; Emission Standards and Test Procedures

    Science.gov (United States)

    This rule will adopt the current voluntary NOx and CO emissions standards of the United Nations International Civil Aviation Organization (ICAO), bringing the United States aircraft standards into alignment with the international standards.

  19. Test Standard Revision Update: JESD57, "Procedures for the Measurement of Single-Event Effects in Semiconductor Devices from Heavy-Ion Irradiation"

    Science.gov (United States)

    Lauenstein, Jean-Marie

    2015-01-01

    The JEDEC JESD57 test standard, Procedures for the Measurement of Single-Event Effects in Semiconductor Devices from Heavy-Ion Irradiation, is undergoing its first revision since 1996. In this talk, we place this test standard into context with other relevant radiation test standards to show its importance for single-event effect radiation testing for space applications. We show the range of industry, government, and end-user party involvement in the revision. Finally, we highlight some of the key changes being made and discuss the trade-space in which setting standards must be made to be both useful and broadly adopted.

  20. A Differential Quadrature Procedure with Regularization of the Dirac-delta Function for Numerical Solution of Moving Load Problem

    Directory of Open Access Journals (Sweden)

    S. A. Eftekhari

    Full Text Available AbstractThe differential quadrature method (DQM is one of the most elegant and efficient methods for the numerical solution of partial differential equations arising in engineering and applied sciences. It is simple to use and also straightforward to implement. However, the DQM is well-known to have some difficulty when applied to partial differential equations involving singular functions like the Dirac-delta function. This is caused by the fact that the Dirac-delta function cannot be directly discretized by the DQM. To overcome this difficulty, this paper presents a simple differential quadrature procedure in which the Dirac-delta function is replaced by regularized smooth functions. By regularizing the Dirac-delta function, such singular function is treated as non-singular functions and can be easily and directly discretized using the DQM. To demonstrate the applicability and reliability of the proposed method, it is applied here to solve some moving load problems of beams and rectangular plates, where the location of the moving load is described by a time-dependent Dirac-delta function. The results generated by the proposed method are compared with analytical and numerical results available in the literature. Numerical results reveal that the proposed method can be used as an efficient tool for dynamic analysis of beam- and plate-type structures traversed by moving dynamic loads.

  1. Problems of professional ethics standards use in auditors’ practice in Ukraine

    Directory of Open Access Journals (Sweden)

    Bondar V.P.

    2017-03-01

    Full Text Available Significant problems of the professional ethics principles violation by auditors cause many problems not only in reliability of disclosed audit opinion, but also cause problems of global stakeholders’ mistrust to the audit profession. This generally creates the barriers for ensuring the transparency of mechanisms of disclosure and verification of Ukrainian business data and does not help form appropriate investment climate. The article finds that auditor’s ethical principles should be regulated and organized on all the levels of the audit quality control ensuring. According to the results of this study, the author highlights these four levels (international, national, local, personal and describes the contribution of each level of documents in the organization of the quality control (in part of ethical principles has been. The research proves the system of organizational support for creating ethical principles compliance environment during carrying out audit assignment based on identifying and eliminating threats to auditors’ independence. In this regard, the author proposes the structure and content of organizational and administrative documents, which are the part of the internal audit quality control system.

  2. Development and operation of a quality assurance system for deviations from standard operating procedures in a clinical cell therapy laboratory.

    Science.gov (United States)

    McKenna, D; Kadidlo, D; Sumstad, D; McCullough, J

    2003-01-01

    Errors and accidents, or deviations from standard operating procedures, other policy, or regulations must be documented and reviewed, with corrective actions taken to assure quality performance in a cellular therapy laboratory. Though expectations and guidance for deviation management exist, a description of the framework for the development of such a program is lacking in the literature. Here we describe our deviation management program, which uses a Microsoft Access database and Microsoft Excel to analyze deviations and notable events, facilitating quality assurance (QA) functions and ongoing process improvement. Data is stored in a Microsoft Access database with an assignment to one of six deviation type categories. Deviation events are evaluated for potential impact on patient and product, and impact scores for each are determined using a 0- 4 grading scale. An immediate investigation occurs, and corrective actions are taken to prevent future similar events from taking place. Additionally, deviation data is collectively analyzed on a quarterly basis using Microsoft Excel, to identify recurring events or developing trends. Between January 1, 2001 and December 31, 2001 over 2500 products were processed at our laboratory. During this time period, 335 deviations and notable events occurred, affecting 385 products and/or patients. Deviations within the 'technical error' category were most common (37%). Thirteen percent of deviations had a patient and/or a product impact score > or = 2, a score indicating, at a minimum, potentially affected patient outcome or moderate effect upon product quality. Real-time analysis and quarterly review of deviations using our deviation management program allows for identification and correction of deviations. Monitoring of deviation trends allows for process improvement and overall successful functioning of the QA program in the cell therapy laboratory. Our deviation management program could serve as a model for other laboratories in

  3. The effect of standard heat and filtration processing procedures on antimicrobial activity and hydrogen peroxide levels in honey.

    Science.gov (United States)

    Chen, Cuilan; Campbell, Leona T; Blair, Shona E; Carter, Dee A

    2012-01-01

    There is increasing interest in the antimicrobial properties of honey. In most honey types, antimicrobial activity is due to the generation of hydrogen peroxide (H(2)O(2)), but this can vary greatly among samples. Honey is a complex product and other components may modulate activity, which can be further affected by commercial processing procedures. In this study we examined honey derived from three native Australian floral sources that had previously been associated with H(2)O(2)-dependent activity. Antibacterial activity was seen in four red stringybark samples only, and ranged from 12 to 21.1% phenol equivalence against Staphylococcus aureus. Antifungal activity ranged from MIC values of 19-38.3% (w/v) against Candida albicans, and all samples were significantly more active than an osmotically equivalent sugar solution. All honey samples were provided unprocessed and following commercial processing. Processing was usually detrimental to antimicrobial activity, but occasionally the reverse was seen and activity increased. H(2)O(2) levels varied from 0 to 1017 μM, and although samples with no H(2)O(2) had little or no antimicrobial activity, some samples had relatively high H(2)O(2) levels yet no antimicrobial activity. In samples where H(2)O(2) was detected, the correlation with antibacterial activity was greater in the processed than in the unprocessed samples, suggesting other factors present in the honey influence this activity and are sensitive to heat treatment. Antifungal activity did not correlate with the level of H(2)O(2) in honey samples, and overall it appeared that H(2)O(2) alone was not sufficient to inhibit C. albicans. We conclude that floral source and H(2)O(2) levels are not reliable predictors of the antimicrobial activity of honey, which currently can only be assessed by standardized antimicrobial testing. Heat processing should be reduced where possible, and honey destined for medicinal use should be retested post-processing to ensure that

  4. Damage measurement of structural material by electron backscatter diffraction. Quantification of measurement quality toward standardization of measurement procedure

    International Nuclear Information System (INIS)

    Kamaya, Masayuki

    2011-01-01

    process, almost identical local misorientations distributions were obtained under different measurement conditions. Finally, for standardization of the measurement procedure of the local misorientation, present knowledge and points to note about measurements were summarized. (author)

  5. PFGE standard operating procedures for Listeria monocytogenes: harmonizing the typing of food and clinical strains in Europe.

    Science.gov (United States)

    Michelon, Damien; Félix, Benjamin; Vingadassalon, Noemie; Mariet, Jean-François; Larsson, Jonas T; Møller-Nielsen, Eva; Roussel, Sophie

    2015-03-01

    Listeria monocytogenes is a foodborne pathogen responsible for a severe disease known as listeriosis. The European Centre for Disease Prevention and Control (ECDC) coordinates a network of national public health laboratories (NPHLs) in charge of typing clinical strains. In food, it is the European Union Reference Laboratory for L. monocytogenes (EURL Lm), which manages a network of National Reference Laboratories (NRLs). A pulsed-field gel electrophoresis (PFGE) standard operating procedure (EURL SOP) has been used routinely at the EURL Lm since 2007. The EURL Lm has recommended that NRLs use the EURL SOP, whereas the Statens Serum Institut (SSI), under contract for ECDC, requested that NPHLs use Halpins' SOP (HSOP) published in 2010 for the PulseNet USA network. An update of Halpins' SOP (uHSOP) was published in 2013. To facilitate the exchange of profiles among human and food European reference laboratories, it is crucial to ensure that the PFGE profiles obtained with these different SOPs are comparable. The aim here was to compare the EURL SOP with HSOP and uHSOP. The panel comprised 114 well-characterized SSI/EURL strains. All were characterized at the EURL using both the EURL SOP and uHSOP. Seventy of the 114 strains were also characterized at the SSI using HSOP. The EURL SOP and uHSOP produced indistinguishable combined (ApaI/AscI) profiles for the 114 strains tested. The EURL SOP and HSOP produced indistinguishable combined profiles for 69 of the 70 strains tested. One strain displayed for the AscI profile an additional low-intensity band at 184 kbp with HSOP. For this strain, SSI and EUR Lm had already observed the same profile from NPHLs and NRLs. However, this deviation is minor as it accounted for about 1% of all the 114 combined profiles. This study should facilitate the exchange of reproducible PFGE profiles among human and food reference laboratories.

  6. Do international labor standards contribute to the persistence of the child-labor problem?

    OpenAIRE

    Doepke, Matthias; Zilibotti, Fabrizio

    2010-01-01

    In recent years, a number of governments and consumer groups in rich countries have tried to discourage the use of child labor in poor countries through measures such as product boycotts and the imposition of international labor standards. The purported objective of such measures is to reduce the incidence of child labor in developing countries and thereby improve children�s welfare. In this paper, we examine the effects of such policies from a political-economy perspective. We show that th...

  7. International standard problem (ISP) No. 41. Containment iodine computer code exercise based on a radioiodine test facility (RTF) experiment

    International Nuclear Information System (INIS)

    2000-04-01

    International Standard Problem (ISP) exercises are comparative exercises in which predictions of different computer codes for a given physical problem are compared with each other or with the results of a carefully controlled experimental study. The main goal of ISP exercises is to increase confidence in the validity and accuracy of the tools, which were used in assessing the safety of nuclear installations. Moreover, they enable code users to gain experience and demonstrate their competence. The ISP No. 41 exercise, computer code exercise based on a Radioiodine Test Facility (RTF) experiment on iodine behaviour in containment under severe accident conditions, is one of such ISP exercises. The ISP No. 41 exercise was borne at the recommendation at the Fourth Iodine Chemistry Workshop held at PSI, Switzerland in June 1996: 'the performance of an International Standard Problem as the basis of an in-depth comparison of the models as well as contributing to the database for validation of iodine codes'. [Proceedings NEA/CSNI/R(96)6, Summary and Conclusions NEA/CSNI/R(96)7]. COG (CANDU Owners Group), comprising AECL and the Canadian nuclear utilities, offered to make the results of a Radioiodine Test Facility (RTF) test available for such an exercise. The ISP No. 41 exercise was endorsed in turn by the FPC (PWG4's Task Group on Fission Product Phenomena in the Primary Circuit and the Containment), PWG4 (CSNI Principal Working Group on the Confinement of Accidental Radioactive Releases), and the CSNI. The OECD/NEA Committee on the Safety of Nuclear Installations (CSNI) has sponsored forty-five ISP exercises over the last twenty-four years, thirteen of them in the area of severe accidents. The criteria for the selection of the RTF test as a basis for the ISP-41 exercise were; (1) complementary to other RTF tests available through the PHEBUS and ACE programmes, (2) simplicity for ease of modelling and (3) good quality data. A simple RTF experiment performed under controlled

  8. [Falling Short of Minimum Volume Standards, Exemptions and Their Consequences from 2018 Onwards. Complex Procedures on Oesophagus and Pancreas in German Hospitals from 2006 to 2014].

    Science.gov (United States)

    de Cruppé, Werner; Geraedts, Max

    2018-03-16

    The minimum volume standards for hospitals in Germany, in force since 2004, provide four exemptions for non-complying hospitals. This study investigates the extent and importance of these exemptions for complex procedures on the oesophagus and pancreas for all non-complying hospitals and for the revised minimum volume regulations in force since the beginning of 2018. Longitudinal, descriptive analyses of data on minimum volume standards and their exemptions for complex procedures on the oesophagus and pancreas, as presented by the hospital quality report cards of the reporting years from 2006 to 2014. For each year and both procedures, about 120 hospitals with some 500 cases report non-compliance with the minimum volume standards. Of these a third report no exemptions (with 180 procedures), a third state emergencies (110), and another third report exemptions due to internal hospital restructuring (210). Ensuring geographical access to care as an exemption is of no importance. After the three year exemption period for installation of a new service line, 20% of the hospitals with procedures on the oesophagus and 30% on the pancreas complied with the minimum volume standards. After the two-year period for staff realignment, the figures were 40 and 50%, respectively. Exemptions do not entirely explain all procedures performed by hospitals not complying with the minimum volume standards. The revised minimum volume regulations' restructuring of exemptions to "emergencies" and "new or renewed service lines" with a two year exemption period, are concordant with the empirical findings of this study. Georg Thieme Verlag KG Stuttgart · New York.

  9. Problems in Standardization of Orthodontic Shear Bond Strength Tests; A Brief Review

    Directory of Open Access Journals (Sweden)

    M.S. A. Akhoundi

    2005-03-01

    Full Text Available Bonding brackets to the enamel surface has gained much popularity today. New adhesive systems have been introduced and marketed and a considerable increase in research regarding bond strength has been published. A considerable amount of these studies deal with shear bond strength of adhesives designed for orthodontic purpose.Previous studies have used variety of test designs. This diversity in test design is due to the fact that there is no standard method for evaluating shear bond strength in orthodontics. Therefore comparison of data obtained from different study is almost impossible.This article tries to briefly discuss the developments occurred in the process of shear bond strength measurement of orthodontic adhesives with an emphasis on the type of test set up and load application.Although the test designs for measuring shear bond strength in orthodontics are still far from ideal, attempts must be made to standardize these tests especially in order to makecomparison of different data easier. It is recommended that test designs be set up in such a manner that better matches with the purpose of the study.

  10. Lithium in Very Metal-poor Dwarf Stars -- Problems for Standard Big Bang Nucleosynthesis?

    International Nuclear Information System (INIS)

    Lambert, David L.

    2004-01-01

    The standard model of primordial nucleosynthesis by the Big Bang as selected by the WMAP-based estimate of the baryon density (Ωbh2) predicts an abundance of 7Li that is a factor of three greater than the generally reported abundance for stars on the Spite plateau, and an abundance of 6Li that is about a thousand times less than is found for some stars on the plateau. This review discusses and examines these two discrepancies. They can likely be resolved without major surgery on the standard model of the Big Bang. In particular, stars on the Spite plateau may have depleted their surface lithium abundance over their long lifetime from the WMAP-based predicted abundances down to presently observed abundances, and synthesis of 6Li (and 7Li) via α + α fusion reactions may have occurred in the early Galaxy. Yet, there remain fascinating ways in which to remove the two discrepancies involving aspects of a new cosmology, particularly through the introduction of exotic particles

  11. The tsunami probabilistic risk assessment (PRA). Example of accident sequence analysis of tsunami PRA according to the standard for procedure of tsunami PRA for nuclear power plants

    International Nuclear Information System (INIS)

    Ohara, Norihiro; Hasegawa, Keiko; Kuroiwa, Katsuya

    2013-01-01

    After the Fukushima Daiichi nuclear power plant (NPP) accident, standard for procedure of tsunami PRA for NPP had been established by the Standardization Committee of AESJ. Industry group had been conducting analysis of Tsunami PRA for PWR based on the standard under the cooperation with electric utilities. This article introduced overview of the standard and examples of accident sequence analysis of Tsunami PRA studied by the industry group according to the standard. The standard consisted of (1) investigation of NPP's composition, characteristics and site information, (2) selection of relevant components for Tsunami PRA and initiating events and identification of accident sequence, (3) evaluation of Tsunami hazards, (4) fragility evaluation of building and components and (5) evaluation of accident sequence. Based on the evaluation, countermeasures for further improvement of safety against Tsunami could be identified by the sensitivity analysis. (T. Tanaka)

  12. Standard problem exercise to validate criticality codes for spent LWR fuel transport container calculations

    International Nuclear Information System (INIS)

    Whitesides, G.H.; Stephens, M.E.

    1984-01-01

    During the past two years, a Working Group established by the Organization for Economic Co-Operation and Development's Nuclear Energy Agency (OECD-NEA) has been developing a set of criticality benchmark problems which could be used to help establish the validity of criticality safety computer programs and their associated nuclear data for calculation of ksub(eff) for spent light water reactor (LWR) fuel transport containers. The basic goal of this effort was to identify a set of actual critical experiments which would contain the various material and geometric properties present in spent LWR transport contrainers. These data, when used by the various computational methods, are intended to demonstrate the ability of each method to accurately reproduce the experimentally measured ksub(eff) for the parameters under consideration

  13. U.S. Geological Survey Noble Gas Laboratory’s standard operating procedures for the measurement of dissolved gas in water samples

    Science.gov (United States)

    Hunt, Andrew G.

    2015-08-12

    This report addresses the standard operating procedures used by the U.S. Geological Survey’s Noble Gas Laboratory in Denver, Colorado, U.S.A., for the measurement of dissolved gases (methane, nitrogen, oxygen, and carbon dioxide) and noble gas isotopes (helium-3, helium-4, neon-20, neon-21, neon-22, argon-36, argon-38, argon-40, kryton-84, krypton-86, xenon-103, and xenon-132) dissolved in water. A synopsis of the instrumentation used, procedures followed, calibration practices, standards used, and a quality assurance and quality control program is presented. The report outlines the day-to-day operation of the Residual Gas Analyzer Model 200, Mass Analyzer Products Model 215–50, and ultralow vacuum extraction line along with the sample handling procedures, noble gas extraction and purification, instrument measurement procedures, instrumental data acquisition, and calculations for the conversion of raw data from the mass spectrometer into noble gas concentrations per unit mass of water analyzed. Techniques for the preparation of artificial dissolved gas standards are detailed and coupled to a quality assurance and quality control program to present the accuracy of the procedures used in the laboratory.

  14. Chapter 9. Educational process. Recommendations and standard operating procedures for intensive care unit and hospital preparations for an influenza epidemic or mass disaster

    NARCIS (Netherlands)

    Richards, Guy A.; Sprung, Charles L.; Christian, Michael D.; Camargo, Ruben; Ceraso, Daniel; Azoulay, Elie; Duguet, Alexandre; Guery, Benoit; Reinhart, Konrad; Adini, Bruria; Barlavie, Yaron; Benin-Goren, Odeda; Cohen, Robert; Klein, Motti; Leoniv, Yuval; Margalit, Gila; Rubinovitch, Bina; Sonnenblick, Moshe; Steinberg, Avraham; Weissman, Charles; Wolff, Donna; Kesecioglu, Jozef; de Jong, Menno; Moreno, Rui; An, Youzhong; Du, Bin; Joynt, Gavin M.; Colvin, John; Loo, Shi; Richards, Guy; Artigas, Antonio; Pugin, Jerome; Amundson, Dennis; Devereaux, Asha; Beigel, John; Danis, Marion; Farmer, Chris; Hick, John L.; Maki, Dennis; Masur, Henry; Rubinson, Lewis; Sandrock, Christian; Talmor, Daniel; Truog, Robert; Zimmerman, Janice; Brett, Steve; Montgomery, Hugh; Rhodes, Andrew; Sanderson, Frances; Taylor, Bruce

    2010-01-01

    To provide recommendations and standard operating procedures (SOPs) for intensive care unit (ICU) and hospital preparations for an influenza pandemic or mass disaster with focus on education of all stakeholders, specifically the emergency executive control groups, ICU staff and staff co-opted to

  15. Chapter 5. Essential equipment, pharmaceuticals and supplies. Recommendations and standard operating procedures for intensive care unit and hospital preparations for an influenza epidemic or mass disaster

    NARCIS (Netherlands)

    Sprung, Charles L.; Kesecioglu, Jozef; Christian, Michael D.; Camargo, Ruben; Ceraso, Daniel; Azoulay, Elie; Duguet, Alexandre; Guery, Benoit; Reinhart, Konrad; Adini, Bruria; Barlavie, Yaron; Benin-Goren, Odeda; Cohen, Robert; Klein, Motti; Leoniv, Yuval; Margalit, Gila; Rubinovitch, Bina; Sonnenblick, Moshe; Steinberg, Avraham; Weissman, Charles; Wolff, Donna; de Jong, Menno; Moreno, Rui; An, Youzhong; Du, Bin; Joynt, Gavin M.; Colvin, John; Loo, Shi; Richards, Guy; Artigas, Antonio; Pugin, Jerome; Amundson, Dennis; Devereaux, Asha; Beigel, John; Danis, Marion; Farmer, Chris; Hick, John L.; Maki, Dennis; Masur, Henry; Rubinson, Lewis; Sandrock, Christian; Talmor, Daniel; Truog, Robert; Zimmerman, Janice; Brett, Steve; Montgomery, Hugh; Rhodes, Andrew; Sanderson, Frances; Taylor, Bruce

    2010-01-01

    To provide recommendations and standard operating procedures for intensive care unit and hospital preparations for an influenza pandemic or mass disaster with a specific focus on essential equipment, pharmaceuticals and supplies. Based on a literature review and expert opinion, a Delphi process was

  16. Chapter 4. Manpower. Recommendations and standard operating procedures for intensive care unit and hospital preparations for an influenza epidemic or mass disaster

    NARCIS (Netherlands)

    Sandrock, Christian; Christian, Michael D.; Camargo, Ruben; Ceraso, Daniel; Azoulay, Elie; Duguet, Alexandre; Guery, Benoit; Reinhart, Konrad; Adini, Bruria; Barlavie, Yaron; Benin-Goren, Odeda; Cohen, Robert; Klein, Motti; Leoniv, Yuval; Margalit, Gila; Rubinovitch, Bina; Sonnenblick, Moshe; Sprung, Charles L.; Steinberg, Avraham; Weissman, Charles; Wolff, Donna; Kesecioglu, Jozef; de Jong, Menno; Moreno, Rui; An, Youzhong; Du, Bin; Joynt, Gavin M.; Colvin, John; Loo, Shi; Richards, Guy; Artigas, Antonio; Pugin, Jerome; Amundson, Dennis; Devereaux, Asha; Beigel, John; Danis, Marion; Farmer, Chris; Hick, John L.; Maki, Dennis; Masur, Henry; Rubinson, Lewis; Talmor, Daniel; Truog, Robert; Zimmerman, Janice; Brett, Steve; Montgomery, Hugh; Rhodes, Andrew; Sanderson, Frances; Taylor, Bruce

    2010-01-01

    To provide recommendations and standard operating procedures (SOPs) for intensive care unit (ICU) and hospital preparations for an influenza pandemic or mass disaster with a specific focus on manpower. Based on a literature review and expert opinion, a Delphi process was used to define the essential

  17. Chapter 1. Introduction. Recommendations and standard operating procedures for intensive care unit and hospital preparations for an influenza epidemic or mass disaster

    NARCIS (Netherlands)

    Sprung, Charles L.; Cohen, Robert; Adini, Bruria; Christian, Michael D.; Camargo, Ruben; Ceraso, Daniel; Azoulay, Elie; Duguet, Alexandre; Guery, Benoit; Reinhart, Konrad; Barlavie, Yaron; Benin-Goren, Odeda; Klein, Motti; Leoniv, Yuval; Margalit, Gila; Rubinovitch, Bina; Sonnenblick, Moshe; Steinberg, Avraham; Weissman, Charles; Wolff, Donna; Kesecioglu, Jozef; de Jong, Menno; Moreno, Rui; An, Youzhong; Du, Bin; Joynt, Gavin M.; Colvin, John; Loo, Shi; Richards, Guy; Artigas, Antonio; Pugin, Jerome; Amundson, Dennis; Devereaux, Asha; Beigel, John; Danis, Marion; Farmer, Chris; Hick, John L.; Maki, Dennis; Masur, Henry; Rubinson, Lewis; Sandrock, Christian; Talmor, Daniel; Truong, Robert; Zimmerman, Janice; Brett, Steve; Montgomery, Hugh; Rhodes, Andrew; Sanderson, Frances; Taylor, Bruce; Monrgomery, Hugh

    2010-01-01

    In December 2007, the European Society of Intensive Care Medicine established a Task Force to develop standard operating procedures (SOPs) for operating intensive care units (ICU) during an influenza epidemic or mass disaster. To provide direction for health care professionals in the preparation and

  18. Chapter 3. Coordination and collaboration with interface units. Recommendations and standard operating procedures for intensive care unit and hospital preparations for an influenza epidemic or mass disaster

    NARCIS (Netherlands)

    Joynt, Gavin M.; Loo, Shi; Taylor, Bruce L.; Margalit, Gila; Christian, Michael D.; Sandrock, Christian; Danis, Marion; Leoniv, Yuval; Sprung, Charles L.; Camargo, Ruben; Ceraso, Daniel; Azoulay, Elie; Duguet, Alexandre; Guery, Benoit; Reinhart, Konrad; Adini, Bruria; Barlavie, Yaron; Benin-Goren, Odeda; Cohen, Robert; Klein, Motti; Rubinovitch, Bina; Sonnenblick, Moshe; Steinberg, Avraham; Weissman, Charles; Wolff, Donna; Kesecioglu, Jozef; de Jong, Menno; Moreno, Rui; An, Youzhong; Du, Bin; Joyng, Gavin M.; Colvin, John; Richards, Guy; Artigas, Antonio; Pugin, Jerome; Amundson, Dennis; Devereaux, Asha; Beigel, John; Farmer, Chris; Hick, John L.; Maki, Dennis; Masur, Henry; Rubinson, Lewis; Talmor, Daniel; Truog, Robert; Zimmerman, Janice; Brett, Steve; Montgomery, Hugh; Rhodes, Andrew; Sanderson, Frances

    2010-01-01

    To provide recommendations and standard operating procedures (SOPs) for intensive care unit (ICU) and hospital preparations for an influenza pandemic or mass disaster with a specific focus on enhancing coordination and collaboration between the ICU and other key stakeholders. Based on a literature

  19. Chapter 7. Critical care triage. Recommendations and standard operating procedures for intensive care unit and hospital preparations for an influenza epidemic or mass disaster

    NARCIS (Netherlands)

    Christian, Michael D.; Joynt, Gavin M.; Hick, John L.; Colvin, John; Danis, Marion; Sprung, Charles L.; Christian, Micahel D.; Camargo, Ruben; Ceraso, Daniel; Azoulay, Elie; Duguet, Alexandre; Guery, Benoit; Reinhart, Konrad; Adini, Bruria; Barlavie, Yaron; Benin-Goren, Odeda; Cohen, Robert; Klein, Motti; Leoniv, Yuval; Margalit, Gila; Rubinovitch, Bina; Sonnenblick, Moshe; Steinberg, Avraham; Weissman, Charles; Wolff, Donna; Kesecioglu, Jozef; de Jong, Menno; Moreno, Rui; An, Youzhong; Du, Bin; Loo, Shi; Richards, Guy; Artigas, Antonio; Pugin, Jerome; Amundson, Dennis; Devereaux, Asha; Beigel, John; Farmer, Chris; Maki, Dennis; Masur, Henry; Rubinson, Lewis; Sandrock, Christian; Talmor, Daniel; Truog, Robert; Zimmerman, Janice; Brett, Steve; Montgomery, Hugh; Rhodes, Andrew; Sanderson, Frances; Taylor, Bruce

    2010-01-01

    To provide recommendations and standard operating procedures for intensive care unit (ICU) and hospital preparations for an influenza pandemic or mass disaster with a specific focus on critical care triage. Based on a literature review and expert opinion, a Delphi process was used to define the

  20. The safety of donor skin preserved with glycerol - Evaluating the Euro Skin Bank preservation procedures of human donor skin against the prEN 12442 standard

    NARCIS (Netherlands)

    Geertsma RE; Wassenaar C; LGM

    2000-01-01

    The procedures for preservation of human donor skin with glycerol, as applied by the Euro Skin Bank (ESB), were evaluated against the prEN 12442 standard: animal tissues and their derivatives used in the manufacture of medical devices. The focus chosen for this review is on risks related to the

  1. Diagnosis and dosimetry of exposure to sulfur mustard: Development of a standard operating procedure for hemoglobin adducts: Exploratory research on albumin and keratin adducts

    NARCIS (Netherlands)

    Noort, D.; Fidder, A.; Jong, L.P.A. de; Schans, G.P. van der; Benschop, H.P.

    2000-01-01

    A standard operating procedure (SOP) for determination of the sulfur mustard adduct to the N-terminal valine in hemoglobin was developed. By using this SOP, it was found that the Nterminal valine adduct in globin of hairless guinea pigs and marmosets which had been exposed to sulfur mustard (0.5

  2. Random access procedures and radio access network (RAN) overload control in standard and advanced long-term evolution (LTE and LTE-A) networks

    DEFF Research Database (Denmark)

    Kiilerich Pratas, Nuno; Thomsen, Henning; Popovski, Petar

    2015-01-01

    In this chapter, we describe and discuss the current LTE random access procedure and the Radio Access Network Load Control solution within LTE/LTE-A. We provide an overview of the several considered load control solutions and give a detailed description of the standardized Extended Access Class B...

  3. Comparison of IEEE383-2003 and IEC60505-2004 standards for harmonization of environmental qualification procedure of electric cable

    International Nuclear Information System (INIS)

    Kim, Jong Seog; Jeong, Sun Chul; Park, Kyung Heum; Jang, Kyung Nam

    2010-01-01

    Needs for harmonization of international equipment qualification(EQ) standards have been raised several years due to purchasing problem of nuclear equipment supplied from abroad country. To meet the regulatory requirement of domestic nuclear power plant, manufacturers have to qualify their equipment in accordance with each standard such as IEEE, IEC and RCC-E. Double qualification increase the equipment cost, which result in high construction cost. Even the unification of each standard have been discussed several years, we have got the long way to go yet. Comparison and harmonization of each international standard will give help to purchase the equipment qualified by not endorsed standard. Environmental qualification, seismic qualification and EMI/EMC qualification are major targets for harmonization. Since concern about cable qualification of 60 years life has been raised recently, harmonization of cable qualification standard also needs to be discussed. KEPRI launched a project for harmonization of EQ relative standards such as IEEE, IEC and RCC-E. A study for harmonization of IEEE323 and IEC60780 is known in progress by IEEE committee. In this paper, harmonization of international standards for cable qualification will be discussed. IEEE383 standard is qualification standard for electric cable broadly used in Asian pacific area while IEC60505 is mostly used in European area. Since these two standards have different requirements for environmental qualification of cable, problem can be happened in the plant site when they purchase cable qualified by not endorsed standard. IEEE383-2003 and IEC60505-2004 is the latest version of each standard. Comparison results and recommendations for harmonization of these two standards are introduced herein

  4. Problems of an expert estimation and importance standardization of the radiating control in Republic of Kazakhstan

    International Nuclear Information System (INIS)

    Baybolov, S.M.; Baygogy, G.O.; Machatova, R.S.

    1999-01-01

    Radioecological condition in Republic of Kazakhstan is one of heaviest and sharp. The information on a condition of an environment many decades was confidential in our former country. A huge industrial complex and heavy industry, insensitively polluting an environment, under state protection against security regulation have destroyed an environmental nature. The long-term nuclear tests in ranges located in territory of Kazakhstan, platform with radioactive departures, mold boards mining-ore of developments (manufactures) operating nuclear power plants, platform for military purposes, dumps and emission of the processing enterprises - everyone are a source of dispersion of radioactive products of division on external environment and infect it. Ground and earth water are ideal environments for commutative accumulation of radioactive substances (radionuclides as Sr-90, Cs-137). Pu-239 strongly going in the top layers of ground and pass in food of a circuit, causing biological action to all alive. Till now there is no card of information system. register of radiation conditions around of ranges, the examination and estimation of the control of food products under the international standards is not adjusted. (author)

  5. Approach to the problem of combined radiation and environmental effect standardization

    International Nuclear Information System (INIS)

    Burykina, L.N.; Ajzina, N.L.; Vasil'eva, L.A.; Veselovskaya, K.A.; Likhachev, Yu.P.; Ponomareva, V.L.; Satarina, S.M.; Shmeleva, E.V.

    1978-01-01

    Rats were used to study combined forms of damage caused by radioactive substances with varioUs types of distribution ( 131 I and 147 Pm) and by external radiation sources (γ, X). Damage caused by radiation and dust factors was also studied. Synergism of the combined effect of the tolerance dose of 147 Pm introduced and preceding external general γ-irradiation was determined. The combined action of 131 I and external γ- and X-ray radiation exhibited an additional effect on rat thyroid glands. The combined action of dust and radiation factors showed that the biological effect depended on the dose abs.orbed in a critical organ (lungs). The results of the investigations point to an important role of critical organs (systems) and the degree of their radiosensitivity in response of body to combined internal and external irradiations. The facts presented show that the approach to standardizing radiation factors from the position of partial summation should be changed. This may be accomplished by using a combination factor which is determined experimentally and reflects a relative biological efficiency of the combined effects as compared to separate ones

  6. Vacuum oscillation solution to the solar neutrino problem in standard and nonstandard pictures

    International Nuclear Information System (INIS)

    Berezhiani, Z.G.; Rossi, A.

    1995-01-01

    The neutrino long wavelength (just-so) oscillation is reexamined as a solution to the solar neutrino problem. We consider the just-so scenario in various cases: in the framework of the solar models with a relaxed prediction of the boron neutrino flux, as well as in the presence of the nonstandard weak range interactions between neutrino and matter constituents. We show that the fit of the experimental data in the just-so scenario is not very good for any reasonable value of the 8 B neutrino flux, but it substantially improves if the nonstandard τ-neutrino--electron interaction is included. These new interactions could also remove the conflict of the just-so picture with the shape of the SN 1987A neutrino spectrum. Special attention is devoted to the potential of the future real-time solar neutrino detectors such as Super-Kamiokande, SNO, and BOREXINO, which could provide the model-independent tests for the just-so scenario. In particular, these imply a specific deformation of the original solar neutrino energy spectra and time variation of the intermediate energy monochromatic neutrino ( 7 Be and pep) signals

  7. Risky procedures by nurses in hospitals: problems and (contemplated) refusals of orders by physicians, and views of physicians and nurses: a questionnaire survey

    NARCIS (Netherlands)

    de Bie, J.; Cuperus-Bosma, J.M.; van der Jagt, M.A.; Gevers, J.K.M.; van der Wal, G.

    2005-01-01

    Occurrence of problems with, refusals of orders and contemplated refusals of orders for risky procedures by nurses in Dutch hospitals and views on the safety of performance was studied using postal questionnaires (600 physicians and 3200 nurses, response 60-71%). Of the respondents, 11-30%

  8. Medical Procedure Problems from the Viewpoint of Elderly Referrals to Healthcare Centers of Hamadan: A Qualitative Study

    Directory of Open Access Journals (Sweden)

    Parisa Parsa

    2017-09-01

    Conclusion The results showed that there are problems of treatment in elderly. So after reviewing the problems with appropriate interventions, training can guide and help the elderly in this area. The authorities can also use findings from research in planning.

  9. Quantization Procedures

    International Nuclear Information System (INIS)

    Cabrera, J. A.; Martin, R.

    1976-01-01

    We present in this work a review of the conventional quantization procedure, the proposed by I.E. Segal and a new quantization procedure similar to this one for use in non linear problems. We apply this quantization procedures to different potentials and we obtain the appropriate equations of motion. It is shown that for the linear case the three procedures exposed are equivalent but for the non linear cases we obtain different equations of motion and different energy spectra. (Author) 16 refs

  10. Standard Model-Axion-Seesaw-Higgs portal inflation. Five problems of particle physics and cosmology solved in one stroke

    International Nuclear Information System (INIS)

    Ballesteros, Guillermo; Ringwald, Andreas; Tamarit, Carlos

    2016-10-01

    We present a minimal extension of the Standard Model (SM) providing a consistent picture of particle physics from the electroweak scale to the Planck scale and of cosmology from inflation until today. Three right-handed neutrinos N_i, a new color triplet Q and a complex SM-singlet scalar σ, whose vacuum expectation value υ_σ∝10"1"1 GeV breaks lepton number and a Peccei-Quinn symmetry simultaneously, are added to the SM. At low energies, the model reduces to the SM, augmented by seesaw generated neutrino masses and mixing, plus the axion. The latter solves the strong CP problem and accounts for the cold dark matter in the Universe. The inflaton is comprised by a mixture of σ and the SM Higgs and reheating of the Universe after inflation proceeds via the Higgs portal. Baryogenesis occurs via thermal leptogenesis. Thus, five fundamental problems of particle physics and cosmology are solved at one stroke in this unified Standard Model-Axion-Seesaw-Higgs portal inflation (SMASH) model. It can be probed decisively by upcoming cosmic microwave background and axion dark matter experiments.

  11. Standard Model–axion–seesaw–Higgs portal inflation. Five problems of particle physics and cosmology solved in one stroke

    Energy Technology Data Exchange (ETDEWEB)

    Ballesteros, Guillermo [Institut de Physique Théorique, Université Paris Saclay, CEA, CNRS, 91191 Gif-sur-Yvette (France); Redondo, Javier [Departamento de Física Teórica, Universidad de Zaragoza, Pedro Cerbuna 12, E-50009, Zaragoza (Spain); Ringwald, Andreas [DESY, Notkestr. 85, 22607 Hamburg (Germany); Tamarit, Carlos, E-mail: guillermo.ballesteros@cea.fr, E-mail: jredondo@unizar.es, E-mail: andreas.ringwald@desy.de, E-mail: carlos.tamarit@durham.ac.uk [Institute for Particle Physics Phenomenology, Durham University, South Road, DH1 3LE (United Kingdom)

    2017-08-01

    We present a minimal extension of the Standard Model (SM) providing a consistent picture of particle physics from the electroweak scale to the Planck scale and of cosmology from inflation until today. Three right-handed neutrinos N {sub i} , a new color triplet Q and a complex SM-singlet scalar σ, whose vacuum expectation value v {sub σ} ∼ 10{sup 11} GeV breaks lepton number and a Peccei-Quinn symmetry simultaneously, are added to the SM. At low energies, the model reduces to the SM, augmented by seesaw generated neutrino masses and mixing, plus the axion. The latter solves the strong CP problem and accounts for the cold dark matter in the Universe. The inflaton is comprised by a mixture of σ and the SM Higgs, and reheating of the Universe after inflation proceeds via the Higgs portal. Baryogenesis occurs via thermal leptogenesis. Thus, five fundamental problems of particle physics and cosmology are solved at one stroke in this unified Standard Model—axion—seesaw—Higgs portal inflation (SMASH) model. It can be probed decisively by upcoming cosmic microwave background and axion dark matter experiments.

  12. Assessing the reliability of the borderline regression method as a standard setting procedure for objective structured clinical examination

    Directory of Open Access Journals (Sweden)

    Sara Mortaz Hejri

    2013-01-01

    Full Text Available Background: One of the methods used for standard setting is the borderline regression method (BRM. This study aims to assess the reliability of BRM when the pass-fail standard in an objective structured clinical examination (OSCE was calculated by averaging the BRM standards obtained for each station separately. Materials and Methods: In nine stations of the OSCE with direct observation the examiners gave each student a checklist score and a global score. Using a linear regression model for each station, we calculated the checklist score cut-off on the regression equation for the global scale cut-off set at 2. The OSCE pass-fail standard was defined as the average of all station′s standard. To determine the reliability, the root mean square error (RMSE was calculated. The R2 coefficient and the inter-grade discrimination were calculated to assess the quality of OSCE. Results: The mean total test score was 60.78. The OSCE pass-fail standard and its RMSE were 47.37 and 0.55, respectively. The R2 coefficients ranged from 0.44 to 0.79. The inter-grade discrimination score varied greatly among stations. Conclusion: The RMSE of the standard was very small indicating that BRM is a reliable method of setting standard for OSCE, which has the advantage of providing data for quality assurance.

  13. Standardization of 2-phenoxyethanol as anesthetic for juvenile Brycon cephalus (Gunther, 1869: the use in field procedures

    Directory of Open Access Journals (Sweden)

    Inoue Luis Antônio Kioshi Aoki

    2004-01-01

    Full Text Available Hyper motility is a negative factor in fish handling procedures due to the risks of damages to the animals. Chemicals are widely used to anesthetize fish during biometry and many other handling procedures. 2-Phenoxyethanol is largely employed, but many studies are necessary about tropical fish responses. The present research evaluated the anesthesia induction time for juvenile matrinxã submitted to eight different levels of 2-phenoxyethanol. The range of 2-phenoxyethanol concentration was 250-600mg liter-1. Induction time of anesthesia decreased as a function of 2-phenoxyethanol concentrations. Fish were safely anesthetized approximately after one minute of exposure to 2-phenoxyethanol batches in concentrations above 400mg/liter, and the recover period was about one minute for all anesthetic concentrations. 2-Phenoxyethanol is a safe anesthetic for juvenile matrinxã even in exposures up to 600mg liter-1 being recommended for many field procedures of fish handling.

  14. On the effect of standard PFEM remeshing on volume conservation in free-surface fluid flow problems

    Science.gov (United States)

    Franci, Alessandro; Cremonesi, Massimiliano

    2017-07-01

    The aim of this work is to analyze the remeshing procedure used in the particle finite element method (PFEM) and to investigate how this operation may affect the numerical results. The PFEM remeshing algorithm combines the Delaunay triangulation and the Alpha Shape method to guarantee a good quality of the Lagrangian mesh also in large deformation processes. However, this strategy may lead to local variations of the topology that may cause an artificial change of the global volume. The issue of volume conservation is here studied in detail. An accurate description of all the situations that may induce a volume variation during the PFEM regeneration of the mesh is provided. Moreover, the crucial role of the parameter α used in the Alpha Shape method is highlighted and a range of values of α for which the differences between the numerical results are negligible, is found. Furthermore, it is shown that the variation of volume induced by the remeshing reduces by refining the mesh. This check of convergence is of paramount importance for the reliability of the PFEM. The study is carried out for 2D free-surface fluid dynamics problems, however the conclusions can be extended to 3D and to all those problems characterized by significant variations of internal and external boundaries.

  15. Comparison of Test Procedures and Energy Efficiency Criteria in Selected International Standards and Labeling Programs for Clothes Washers, Water Dispensers, Vending Machines and CFLs

    Energy Technology Data Exchange (ETDEWEB)

    Fridley, David; Zheng, Nina; Zhou, Nan

    2010-06-01

    Since the late 1970s, energy labeling programs and mandatory energy performance standards have been used in many different countries to improve the efficiency levels of major residential and commercial equipment. As more countries and regions launch programs covering a greater range of products that are traded worldwide, greater attention has been given to harmonizing the specific efficiency criteria in these programs and the test methods for measurements. For example, an international compact fluorescent light (CFL) harmonization initiative was launched in 2006 to focus on collaboration between Australia, China, Europe and North America. Given the long history of standards and labeling programs, most major energy-consuming residential appliances and commercial equipment are already covered under minimum energy performance standards (MEPS) and/or energy labels. For these products, such as clothes washers and CFLs, harmonization may still be possible when national MEPS or labeling thresholds are revised. Greater opportunity for harmonization exists in newer energy-consuming products that are not commonly regulated but are under consideration for new standards and labeling programs. This may include commercial products such as water dispensers and vending machines, which are only covered by MEPS or energy labels in a few countries or regions. As China continues to expand its appliance standards and labeling programs and revise existing standards and labels, it is important to learn from recent international experiences with efficiency criteria and test procedures for the same products. Specifically, various types of standards and labeling programs already exist in North America, Europe and throughout Asia for products in China's 2010 standards and labeling programs, namely clothes washers, water dispensers, vending machines and CFLs. This report thus examines similarities and critical differences in energy efficiency values, test procedure specifications and

  16. Effects of Video-Based and Applied Problems on the Procedural Math Skills of Average- and Low-Achieving Adolescents.

    Science.gov (United States)

    Bottge, Brian A.; Heinrichs, Mary; Chan, Shih-Yi; Mehta, Zara Dee; Watson, Elizabeth

    2003-01-01

    This study examined effects of video-based, anchored instruction and applied problems on the ability of 11 low-achieving (LA) and 26 average-achieving (AA) eighth graders to solve computation and word problems. Performance for both groups was higher during anchored instruction than during baseline, but no differences were found between instruction…

  17. Development and evaluation of Standard Operating Procedures (SOPs) for quality control tests and radiological protection activities in a Nuclear Medicine Service

    Energy Technology Data Exchange (ETDEWEB)

    Krempser, Alexandre R., E-mail: krempser@peb.ufrj.br [Universidade Federal do Rio de Janeiro (PEB/COPPE/UFRJ), RJ (Brazil). Programa de Engenharia Biomedica; Soares, Alexandre B. [Universidade Federal do Rio de Janeiro (IF/UFRJ), Rio de Janeiro, RJ (Brazil). Inst. de Fisica; Corbo, Rossana [Universidade Federal do Rio de Janeiro (FM/UFRJ), Rio de Janeiro, RJ (Brazil). Dept. de Radiologia

    2011-07-01

    The quality management in Nuclear Medicine Services is a requirement of national and international standards. The Brazilian regulatory agency in health surveillance, the Agencia Nacional de Vigilancia Sanitaria (ANVISA), in its Resolucao de Diretoria Colegiada (Collegiate Directory Resolution) no. 38, requires the elaboration of documents describing the technical and clinical routine activities. This study aimed to elaborate, implement and evaluate Standard Operating Procedures (SOPs) for quality control tests and radiological protection activities in the Nuclear Medicine Service of a university hospital. Eighteen SOPs were developed, involving tasks related to dose calibrator, gamma camera, Geiger-Muller detectors and radiological protection activities. The performance of its application was evaluated for a period of six months. It was observed a reduction in 75% of reported operational errors and 42% of the number of reported incidents with contamination by radioactive material. The SOPs were adequate and successful in its application. New procedures involving clinical activities will also be developed and evaluated. (author)

  18. Consent for routine neonatal procedures: A study of practices in Irish neonatal units. How do we compare with the gold standard BAPM guidelines?

    Science.gov (United States)

    Ryan, M A; Ryan, C A; Dempsey, E; O'Connell, R

    2017-06-09

    The Irish National Consent Policy (NCP) proposes that the legal requirement for consent extends to all forms of interventions, investigations and treatment, carried out on or behalf of the Health Service Executive (HSE). This study employs a quantitative descriptive approach to investigate the practices for obtaining consent for an identified group of routine neonatal procedures in neonatal facilities throughout Ireland. The BAPM (British Association of Perinatal Medicine) guidelines were identified as 'gold standard' for the purposes of this study. The results indicated a lack of consistency between participating units pertaining to the modes of consent utilised and notable variances from 'gold standard' guidelines. Unanimity was evident for 3 procedures only (administering BCG, 6-in-1, and donor breast milk to infant). Significant findings related to EEG with video recordings, MRI/CT and gastro intestinal imaging, screening of an infant with suspected substance abuse or retinopathy of prematurity screening (ROP), administration of Vitamin K, and the carrying out of a lumbar puncture.

  19. Enhancing Title Ix Due Process Standards in Campus Sexual Assault Adjudication: Considering the Roles of Distributive, Procedural, and Restorative Justice

    Science.gov (United States)

    Harper, Shannon; Maskaly, Jon; Kirkner, Anne; Lorenz, Katherine

    2017-01-01

    Title IX prohibits sex discrimination--including sexual assault--in higher education. The Department of Education Office for Civil Rights' 2011 "Dear Colleague Letter" outlines recommendations for campus sexual assault adjudication allowing a variety of procedures that fail to protect accused students' due process rights and victims'…

  20. Final Rule for Control of Air Pollution From Aircraft and Aircraft Engines; Emission Standards and Test Procedures

    Science.gov (United States)

    EPA adopted emission standards and related provisions for aircraft gas turbine engines with rated thrusts greater than 26.7 kilonewtons. These engines are used primarily on commercial passenger and freight aircraft.

  1. Pylorus preserving pancreaticoduodenectomy versus standard Whipple procedure: a prospective, randomized, multicenter analysis of 170 patients with pancreatic and periampullary tumors

    NARCIS (Netherlands)

    K.T. Tran; H.G. Smeenk; C.H.J. van Eijck (Casper); G. Kazemier (Geert); W.C.J. Hop (Wim); J.W. Greve (Jan Willem); O.T. Terpstra (Onno); J.A. Zijlstra (Jan); P. Klinkert; J. Jeekel (Hans)

    2004-01-01

    textabstractOBJECTIVE: A prospective randomized multicenter study was performed to assess whether the results of pylorus-preserving pancreaticoduodenectomy (PPPD) equal those of the standard Whipple (SW) operation, especially with respect to duration of surgery, blood loss,

  2. Postoperative weight gain after standard Whipple's procedure versus pylorus-preserving pancreatoduodenectomy: the influence of tumour status

    NARCIS (Netherlands)

    van Berge Henegouwen, M. I.; Moojen, T. M.; van Gulik, T. M.; Rauws, E. A.; Obertop, H.; Gouma, D. J.

    1998-01-01

    BACKGROUND: Recent reports suggest a better postoperative weight gain after pylorus-preserving pancreatoduodenectomy (PPPD) compared with standard pancreatoduodenectomy (PD). Factors that could also influence postoperative weight gain, such as tumour-positive resection margins and tumour recurrence,

  3. Patient controlled sedation using a standard protocol for dressing changes in burns: patients' preference, procedural details and a preliminary safety evaluation.

    Science.gov (United States)

    Nilsson, Andreas; Steinvall, Ingrid; Bak, Zoltan; Sjöberg, Folke

    2008-11-01

    Patient controlled sedation (PCS) enables patients to titrate doses of drugs by themselves during different procedures involving pain or discomfort. We studied it in a prospective crossover design using a fixed protocol without lockout time to examine it as an alternative method of sedation for changing dressings in burned patients. Eleven patients with >10% total burn surface area (TBSA) had their dressings changed, starting with sedation by an anaesthetist (ACS). The second dressing change was done with PCS (propofol/alfentanil) and the third time the patients had to choose ACS or PCS. During the procedures, data on cardiopulmonary variables, sedation (bispectral index), pain intensity (VAS), procedural details, doses of drugs, and patients' preferences were collected to compare the two sedation techniques. The study data indicated that wound care in burned patients is feasible with a standardized PCS protocol. The patients preferred PCS to ACS on the basis of self-control, and because they had less discomfort during the recovery period. Wound care was also considered adequate by the staff during PCS. No respiratory (respiratory rate/transcutaneous PCO(2)) or cardiovascular (heart rate/blood pressure) adverse events were recorded at any time during any of the PCS procedures. The doses of propofol and alfentanil and BIS index decrease were less during PCS than ACS. Procedural pain was higher during PCS but lower after the procedure. We suggest that PCS using a standard protocol is an interesting alternative to anaesthetist-provided sedation during dressing changes. It seems effective, saves resources, is safe, and at same time is preferred by the patients. The strength of these conclusions is, however, hampered by the small size of this investigation and therefore further studies are warranted.

  4. Solving a multi-objective manufacturing cell scheduling problem with the consideration of warehouses using a simulated annealing based procedure

    Directory of Open Access Journals (Sweden)

    Adrián A. Toncovich

    2019-01-01

    Full Text Available The competition manufacturing companies face has driven the development of novel and efficient methods that enhance the decision making process. In this work, a specific flow shop scheduling problem of practical interest in the industry is presented and formalized using a mathematical programming model. The problem considers a manufacturing system arranged as a work cell that takes into account the transport operations of raw material and final products between the manufacturing cell and warehouses. For solving this problem, we present a multiobjective metaheuristic strategy based on simulated annealing, the Pareto Archived Simulated Annealing (PASA. We tested this strategy on two kinds of benchmark problem sets proposed by the authors. The first group is composed by small-sized problems. On these tests, PASA was able to obtain optimal or near-optimal solutions in significantly short computing times. In order to complete the analysis, we compared these results to the exact Pareto front of the instances obtained with augmented ε-constraint method. Then, we also tested the algorithm in a set of larger problems to evaluate its performance in more extensive search spaces. We performed this assessment through an analysis of the hypervolume metric. Both sets of tests showed the competitiveness of the Pareto Archived Simulated Annealing to efficiently solve this problem and obtain good quality solutions while using reasonable computational resources.

  5. CIEMAT contribution to the international standard problem ISP-34: contain analysis of FAL-ISP 1 test

    International Nuclear Information System (INIS)

    Herranz, L.E.; Polo, J.

    1994-01-01

    CIEMAT, along with a great number of international laboratories, has participated in the open exercise of the first International Standard Problem addressing fission product transport issues. The FAL-ISP 1, aimed to study particle agglomeration, has been simulated with CONTAIN code. The thermalhydraulic results obtained have been satisfactory and aerosols ones have been reasonably accurate. However, some discrepancies appeared between predictions and experimental data; these are essentially related to the injection phase of the experiment, where the major influence of input approximations took place. In addition, the rationalization of discrepancies pointed potential data inconsistencies. Some parametric studies showed the results sensitivity to input assumptions concerning aerosol characterization and default values in CONTAIN; in general, they confirmed the suitability of most of the approximations taken. (Author)

  6. Ciemat Contribution to The International Standard Problem ISP-34: Contain Analysis of Fal-ISP 1 Test

    International Nuclear Information System (INIS)

    Herranz, L. E.; Polo, J.

    1994-01-01

    CIEMAT, along with a great number of international laboratories, has participated in the open exercise of the first International Standard Problem addressing fission product transport issues. The FAL-ISP 1, aimed to study particle agglomeration, has been simulated with CONTAIN code. The therma hydraulic results obtained have been satisfactory and aerosol ones have been reasonably accurate. However, some discrepancies appeared between predictions and experimental data; these are essentially related to the injection phase of the experiment, where the major influence of input approximations took place. In addition, the rationalization of discrepancies pointed potential data inconsistencies. Some parametric studies showed the results sensitivity to input assumptions concerning aerosol characterization and default values in CONTAIN; in general, they confirmed the suitability of most of the approximations taken. (Author) 11 refs

  7. ISP 22 OECD/NEA/CSNI International standard problem n. 22. Evaluation of post-test analyses

    International Nuclear Information System (INIS)

    1992-07-01

    The present report deals with the open re-evaluation of the originally double-blind CSNI International Standard Problem 22 based on the test SP-FW-02 performed in the SPES facility. The SPES apparatus is an experimental simulator of the Westinghouse PWR-PUN plant. The test SP-FW-02 (ISP22) simulates a complete loss of feedwater with delayed injection of auxiliary feedwater. The main parts of the report are: outline of the test facility and of the SP-FW-02 experiment; overview of pre-test activities; overview of input models used by post-test participants; evaluation of participant predictions; evaluation of qualitative and quantitative code accuracy of pre-test and post-test calculations

  8. The problem questions of update the legislation of Ukraine in aspect of professional representation a lawyer in civil procedure

    Directory of Open Access Journals (Sweden)

    Максим Володимирович Шпак

    2017-03-01

    According to the author’s opinion of this scientific article, the subject of the legislative initiative need proposed more detailed specifics of insignificant property dispute, its content and features of procedural representation of a lawyer for such categories of cases.

  9. Patient Recall of Informed Consent at 4 Weeks After Total Hip Replacement With Standardized Versus Procedure-Specific Consent Forms.

    Science.gov (United States)

    Pomeroy, Eoghan; Shaarani, Shahril; Kenyon, Robert; Cashman, James

    2017-08-25

    Informed consent plays a pivotal role in the operative process, and surgeons have an ethical and legal obligation to provide patients with information to allow for shared decision-making. Unfortunately, patient recall after the consent process is frequently poor. This study aims to evaluate the effect of procedure-specific consent forms on patient's recall four weeks after total hip replacement (THR). This is a prospective study using a posttest-only control group design. Sixty adult patients undergoing total hip replacement were allocated to be consented using either the generic or the surgery-specific consent form. Four weeks after surgery, a phone interview was conducted to assess patient's recall of risk of surgical complications. Patient demographic characteristics and educational attainment were similar in both groups. There was a statistically significant increase in the mean number of risks recalled in the study group at 1.43 compared with 0.67 in the control group (P = 0.0131). Consent is a complex process, and obtaining informed consent is far from straightforward. A statistically significant improvement in patient's recall with the use of procedure-specific consent forms was identified, and based on this, we would advocate their use. However, overall patient recall in both groups was poor. We believe that improving the quality of informed consent may require the sum of small gains, and the use of procedure-specific consent forms may aid in this regard.

  10. Application of the standard options of the FITNET procedure to the structural integrity assessment of welded specimens containing cracks

    International Nuclear Information System (INIS)

    Dzioba, Ihor; Neimitz, Andrzej

    2007-01-01

    In this paper, the structural integrity of welded specimens is assessed. The specimens were welded using a conventional technique, MAG, and an unconventional one, laser technology. Welded specimens were of the central crack under tension (CCT) type. The elements were loaded, the maximum load was recorded, and the second and the third options of the FITNET procedure were utilized to estimate the critical loading. Estimated and recorded loads were compared to verify the conservatism of the estimated results. For comparison, the results obtained using Option 1 of the FITNET procedure (not recommended in the case analysed) are also presented. Results of the mechanical properties, hardness, fracture toughness for the base and the weld material and residual stress distributions are reported for both MAG and laser welding techniques. The results obtained confirm that the FITNET procedures were properly deigned. The higher the level of analysis, the smaller the conservatism of predictions observed. The overconservative conclusions, following from the lower level of analysis, suggest that the structural element is endangered, do not have to exclude it from exploitation. The higher level of analysis can, in some cases, confirm that the structural element containing a crack can still be exploited

  11. Discharge communication from inpatient care: an audit of written medical discharge summary procedure against the new National Health Service Standard for clinical handover.

    Science.gov (United States)

    Reid, Daniel Brooks; Parsons, Shaun R; Gill, Stephen D; Hughes, Andrew J

    2015-04-01

    To audit written medical discharge summary procedure and practice against Standard Six (clinical handover) of the Australian National Safety and Quality Health Service Standards at a major regional Victorian health service. Department heads were invited to complete a questionnaire about departmental discharge summary practices. Twenty-seven (82%) department heads completed the questionnaire. Seven (26%) departments had a documented discharge summary procedure. Fourteen (52%) departments monitored discharge summary completion and 13 (48%) departments monitored the timeliness of completion. Seven (26%) departments informed the patient of the content of the discharge summary and six (22%) departments provided the patient with a copy. Seven (26%) departments provided training for staff members on how to complete discharge summaries. Completing discharge summaries was usually delegated to the medical intern. The introduction of the National Service Standards prompted an organisation-wide audit of discharge summary practices against the external criterion. There was substantial variation in the organisation's practices. The Standards and the current audit results highlight an opportunity for the organisation to enhance and standardise discharge summary practices and improve communication with general practice.

  12. Standard Procedure for Dose Assessment using the film holder NRPB/AERE and the film AGFA Monitoring 2/10

    International Nuclear Information System (INIS)

    Guillen, J.A.

    1998-07-01

    This paper describes the calculation method to assess dose and energy using the film holder from NRPB/AERE and the film Agfa Monitoring 2/10. Also includes all the steps since preparing the standard curve, fitting of calibration curve, dose assesment, description of filtration of the film holder and the form of the calibration curve

  13. A Randomized Controlled Trial to Compare e-Feedback Versus "Standard" Face-to-Face Verbal Feedback to Improve the Acquisition of Procedural Skill.

    Science.gov (United States)

    Al-Jundi, Wissam; Elsharif, Mohamed; Anderson, Melanie; Chan, Phillip; Beard, Jonathan; Nawaz, Shah

    Constructive feedback plays an important role in learning during surgical training. Standard feedback is usually given verbally following direct observation of the procedure by a trained assessor. However, such feedback requires the physical presence of expert faculty members who are usually busy and time-constrained by clinical commitments. We aim to evaluate electronic feedback (e-feedback) after video observation of surgical suturing in comparison with standard face-to-face verbal feedback. A prospective, blinded, randomized controlled trial comparing e-feedback with standard verbal feedback was carried out in February 2015 using a validated pro formas for assessment. The study participants were 38 undergraduate medical students from the University of Sheffield, UK. They were recorded on video performing the procedural skill, completed a self-evaluation form, and received e-feedback on the same day (group 1); observed directly by an assessor, invited to provide verbal self-reflection, and then received standard verbal feedback (group 2). In both groups, the feedback was provided after performing the procedure. The participants returned 2 days later and performed the same skill again. Poststudy questionnaire was used to assess the acceptability of each feedback among the participants. Overall, 19 students in group 1 and 18 students in group 2 completed the study. Although there was a significant improvement in the overall mean score on the second performance of the task for all participants (first performance mean 11.59, second performance mean 15.95; p ≤ 0.0001), there was no difference in the overall mean improvement score between group 1 and group 2 (4.74 and 3.94, respectively; p = 0.49). The mean overall scores for the e-feedback group at baseline recorded by 2 independent investigators showed good agreement (mean overall scores of 12.84 and 11.89; Cronbach α = 0.86). Poststudy questionnaire demonstrated that both e-feedback and standard verbal feedback

  14. Key-Feature-Probleme zum Prüfen von prozeduralem Wissen: Ein Praxisleitfaden [Key Feature Problems for the assessment of procedural knowledge: a practical guide

    Directory of Open Access Journals (Sweden)

    Kopp, Veronika

    2006-08-01

    Full Text Available [english] After assigning the different examination formats to the diverse terms of Miller's pyramide of knowledge, this paper provides a short presentation of the key feature approach by giving the definition and an example for clarification. Afterwards, a practical guide to writing key feature problems is given consisting of the following steps: define the domain, choose a clinical situation, define the key features, develop a test case scenario, write questions, select a preferred response format, define the scoring key, and validation. Finally, we present the evaluation results of this practical guide. In sum, the participants were very pleased with it. The differences between the estimations of their knowledge before and after the workshop concerning key features were significant. The key feature approach is an innovative tool for assessing clinical decision-making skills, also for electronical examinations. Substituting the write-in format for the long-menu format allows an automatic data analysis. [german] Im vorliegenden Beitrag wird - nach der Zuordnung unterschiedlicher Prüfungsformen zu den verschiedenen Wissensarten der Wissenspyramide von Miller - der Key-Feature (KF Ansatz vorgestellt. Nachdem anhand der Definition und einem Beispiel erklärt wurde, was ein KF ist, wird im Anschluss eine Anleitung für die Erstellung eines KF-Problems gegeben. Diese besteht aus folgenden Schritten: Definition des Kontextes, Wahl der klinischen Situation, Identifikation der KFs des klinischen Problems, Schreiben des klinischen Szenarios (Fallvignette, Schreiben der einzelnen KF-Fragen, Auswahl des Antwortformates, Bewertungsverfahren und Inhaltsvalidierung. Am Ende werden die Ergebnisse einer Evaluation dieser Anleitung, die im Rahmen eines KF-Workshops gewonnen wurden, präsentiert. Die Teilnehmer waren mit dieser Workshopeinheit sehr zufrieden und gaben an, sehr viel gelernt zu haben. Die subjektive Einschätzung ihres Wissensstands vor und nach

  15. Improving the performance of the partitioned QN-ILS procedure for fluid-structure interaction problems: filtering

    CSIR Research Space (South Africa)

    Haelterman, R

    2016-07-01

    Full Text Available be mathematically stated in the following form: F (g) = pS(p) = g, (1) where F : DF ⊂ Rm → Rn : g 7→ F (g) and S : DS ⊂ Rn → Rm : p 7→ S(p). Each equation describes (the discretized equations of) a physical problem that is spatially decomposed. In fluid... physical problem, it often represents the equations obtained after discretizing the continuous equations in time and space, and thus only represents the evolution over one time-step (see §3). This is an example of how we could be presented with a series...

  16. Conscious sedation for endoscopic and non-endoscopic interventional gastrointestinal procedures: meeting patients' expectations, missing the standard

    Energy Technology Data Exchange (ETDEWEB)

    Marriott, P.; Laasch, H.-U.; Wilbraham, L.; Marriott, A.; England, R.E.; Martin, D.F. E-mail: derrick.martin@smtr.nhs.uk

    2004-02-01

    AIM: To assess the level of sedation, patient satisfaction and frequency of unplanned events with conscious sedation for interventional procedures. MATERIALS AND METHODS: One hundred and seventeen patients were assessed prospectively before, during and after procedures. Blood pressure, pulse, oxygen saturation and sedation level were monitored and patients followed up after 24 h. Sedation was scored after drugs were given in accordance with an established protocol. Doses were recorded, as were patients' weight, age and ASA grade and any unplanned events and their management. RESULTS: Seventy-six of the 117 patients (65%) had no unplanned event, 20 (17.1%) became agitated, 15 (12.8%) hypotensive, three (2.6%) hypoxic and three (2.6%) had more than one response. Twelve patients required active management. Fifty-two (44.4%) had a sedation level of {<=}3 (responsive to verbal commands), but 39 (33.3%) reached level 6. Median doses were midazolam 6 mg (1-20 mg) and pethidine 50 mg (12.5-100 mg). Ninety-three percent were satisfied with their sedation. No adverse effects were observed after 24 h. CONCLUSION: Despite using a sedation protocol, unplanned events occurred in 35% (95% CI=27-44%) of patients, although not all required active management. The sedation levels reached in some exceeded guidelines. Unplanned events were commoner with increased sedation level. Patient satisfaction was high and no permanent damage was observed.

  17. Conscious sedation for endoscopic and non-endoscopic interventional gastrointestinal procedures: meeting patients' expectations, missing the standard

    International Nuclear Information System (INIS)

    Marriott, P.; Laasch, H.-U.; Wilbraham, L.; Marriott, A.; England, R.E.; Martin, D.F.

    2004-01-01

    AIM: To assess the level of sedation, patient satisfaction and frequency of unplanned events with conscious sedation for interventional procedures. MATERIALS AND METHODS: One hundred and seventeen patients were assessed prospectively before, during and after procedures. Blood pressure, pulse, oxygen saturation and sedation level were monitored and patients followed up after 24 h. Sedation was scored after drugs were given in accordance with an established protocol. Doses were recorded, as were patients' weight, age and ASA grade and any unplanned events and their management. RESULTS: Seventy-six of the 117 patients (65%) had no unplanned event, 20 (17.1%) became agitated, 15 (12.8%) hypotensive, three (2.6%) hypoxic and three (2.6%) had more than one response. Twelve patients required active management. Fifty-two (44.4%) had a sedation level of ≤3 (responsive to verbal commands), but 39 (33.3%) reached level 6. Median doses were midazolam 6 mg (1-20 mg) and pethidine 50 mg (12.5-100 mg). Ninety-three percent were satisfied with their sedation. No adverse effects were observed after 24 h. CONCLUSION: Despite using a sedation protocol, unplanned events occurred in 35% (95% CI=27-44%) of patients, although not all required active management. The sedation levels reached in some exceeded guidelines. Unplanned events were commoner with increased sedation level. Patient satisfaction was high and no permanent damage was observed

  18. Selection of optimal treatment procedures for non-standard radioactive waste arising from decommissioning of NPP after accident

    Energy Technology Data Exchange (ETDEWEB)

    Strážovec, Roman, E-mail: strazovec.roman@javys.sk [Institute of Nuclear and Physical Engineering, Slovak University of Technology in Bratislava, Ilkovičova 3, 812 19 Bratislava (Slovakia); JAVYS, a.s., Tomášikova 22, 821 02 Bratislava (Slovakia); Hrnčíř, Tomáš [DECOM, a.s., Sibírska 1, 917 01 Trnava (Slovakia); Lištjak, Martin [Institute of Nuclear and Physical Engineering, Slovak University of Technology in Bratislava, Ilkovičova 3, 812 19 Bratislava (Slovakia); VUJE, a.s., Okružná 5, 918 64 Trnava (Slovakia); Nečas, Vladimír [Institute of Nuclear and Physical Engineering, Slovak University of Technology in Bratislava, Ilkovičova 3, 812 19 Bratislava (Slovakia)

    2016-05-15

    The decommissioning of nuclear power plants is becoming a standard industrial activity where the optimization processes of partial activities are inevitable mainly for technical and economic reasons. In Slovakia, the decommissioning of A1 NPP is very specific case because A1 NPP is rare type of NPP (prototype) and furthermore its operation was affected by the accident. A large number of specific non-standard radioactive waste, such as long-time storage cases (hereinafter LSC), that is not usually present within the decommissioning projects of NPP with a regular termination of operation, represent one of the significant consequences of the accident and issues arisen from follow-up activities. The presented article describes the proposal of processing and conditioning of non-standard radioactive waste (such as LSC), together with description of methodology applied in the proposal for update of waste acceptance criteria for the processing and conditioning of radioactive waste (hereinafter RAW) within Bohunice Radioactive waste Treatment and Conditioning Centre (hereinafter RWTC). The results of performed detailed analysis are summarized into new waste acceptance criteria for technological lines keeping in mind safety principles and requirements for protection of operating personnel, the public and the environment.

  19. Model for the Value of a Business, Some Optimisation Problems in its Operating Procedures and the Valuation of its Debt

    OpenAIRE

    M.Z. Apabhai; N.I. Georgikopoulos; D. Hasnip; R.K.D. Jamie; M. Kim

    1999-01-01

    In this paper we present a model for the value of a firm based on observable variables and parameters: the annual turnover, the expenses, interest rates. This value is the solution of a parabolic partial differential equation. We show how the value of the company depends on its legal status such as its liability (i.e. whether it is a Limited Company or a sole trader/partnership). We give examples of how the operating procedures can be optimised (e.g. whether the firm should close down, reloca...

  20. PLAN-TA9-2443(U), Rev. B Remediated Nitrate Salt (RNS) Surrogate Formulation and Testing Standard Procedure

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Geoffrey Wayne [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-03-16

    This document identifies scope and some general procedural steps for performing Remediated Nitrate Salt (RNS) Surrogate Formulation and Testing. This Test Plan describes the requirements, responsibilities, and process for preparing and testing a range of chemical surrogates intended to mimic the energetic response of waste created during processing of legacy nitrate salts. The surrogates developed are expected to bound1 the thermal and mechanical sensitivity of such waste, allowing for the development of process parameters required to minimize the risk to worker and public when processing this waste. Such parameters will be based on the worst-case kinetic parameters as derived from APTAC measurements as well as the development of controls to mitigate sensitivities that may exist due to friction, impact, and spark. This Test Plan will define the scope and technical approach for activities that implement Quality Assurance requirements relevant to formulation and testing.

  1. MATLAB-implemented estimation procedure for model-based assessment of hepatic insulin degradation from standard intravenous glucose tolerance test data.

    Science.gov (United States)

    Di Nardo, Francesco; Mengoni, Michele; Morettini, Micaela

    2013-05-01

    Present study provides a novel MATLAB-based parameter estimation procedure for individual assessment of hepatic insulin degradation (HID) process from standard frequently-sampled intravenous glucose tolerance test (FSIGTT) data. Direct access to the source code, offered by MATLAB, enabled us to design an optimization procedure based on the alternating use of Gauss-Newton's and Levenberg-Marquardt's algorithms, which assures the full convergence of the process and the containment of computational time. Reliability was tested by direct comparison with the application, in eighteen non-diabetic subjects, of well-known kinetic analysis software package SAAM II, and by application on different data. Agreement between MATLAB and SAAM II was warranted by intraclass correlation coefficients ≥0.73; no significant differences between corresponding mean parameter estimates and prediction of HID rate; and consistent residual analysis. Moreover, MATLAB optimization procedure resulted in a significant 51% reduction of CV% for the worst-estimated parameter by SAAM II and in maintaining all model-parameter CV% MATLAB-based procedure was suggested as a suitable tool for the individual assessment of HID process. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

  2. A Singlet Extension of the Minimal Supersymmetric Standard Model: Towards a More Natural Solution to the Little Hierarchy Problem

    Energy Technology Data Exchange (ETDEWEB)

    de la Puente, Alejandro [Univ. of Notre Dame, IN (United States)

    2012-05-01

    In this work, I present a generalization of the Next-to-Minimal Supersymmetric Standard Model (NMSSM), with an explicit μ-term and a supersymmetric mass for the singlet superfield, as a route to alleviating the little hierarchy problem of the Minimal Supersymmetric Standard Model (MSSM). I analyze two limiting cases of the model, characterized by the size of the supersymmetric mass for the singlet superfield. The small and large limits of this mass parameter are studied, and I find that I can generate masses for the lightest neutral Higgs boson up to 140 GeV with top squarks below the TeV scale, all couplings perturbative up to the gauge unification scale, and with no need to fine tune parameters in the scalar potential. This model, which I call the S-MSSM is also embedded in a gauge-mediated supersymmetry breaking scheme. I find that even with a minimal embedding of the S-MSSM into a gauge mediated scheme, the mass for the lightest Higgs boson can easily be above 114 GeV, while keeping the top squarks below the TeV scale. Furthermore, I also study the forward-backward asymmetry in the t¯t system within the framework of the S-MSSM. For this purpose, non-renormalizable couplings between the first and third generation of quarks to scalars are introduced. The two limiting cases of the S-MSSM, characterized by the size of the supersymmetric mass for the singlet superfield is analyzed, and I find that in the region of small singlet supersymmetric mass a large asymmetry can be obtained while being consistent with constraints arising from flavor physics, quark masses and top quark decays.

  3. Problems of drawing up standards for persons simultaneously engaged in more than one activity involving radiation hazards

    International Nuclear Information System (INIS)

    Lucci, F.; Pelliccioni, M.

    1979-01-01

    The authors examine, from the points of view of the ICRP recommendations and of national and international standards, radiation protection problems posed by persons simultaneously engaged in professional activities involving radiation hazards in more than one place. The consequences of this type of situation, for the radiological protection classification of workers and for the evaluation and recording of doses received, are described in detail. In order to ensure proper monitoring of doses, agreements must be reached in advance between those in charge of the different areas of activity. Three cases seem to be of particular relevance: (a) that of workers who, while working for a single employer, perform in more than one place activities in which they are exposed to ionizing radiation (scientists working at different research centres, employees of companies specialized in the nuclear field, including the use of isotopes, accelerators, etc.); (b) that of workers who are engaged by more than one employer and are exposed to ionizing radiations as a result of their activities at different establishments (a special case is that of doctors who are radiologists or specialists in some other branch of nuclear medicine and work both as employees and independently in their own practices); and (c) that of employees of outside organizations not directly concerned with nuclear activities who are only exposed to ionizing radiation when called upon to work in establishments possessing sources of radiation. Finally, the authors suggest some ways of solving these problems - though they are rather difficult to define objectively (for example the case of medical practioners). (author)

  4. MO-F-304-01: Applying PDSA to a Practical Clinical Problem: Variation in Procedural Doses Among Interventional Radiologists

    Energy Technology Data Exchange (ETDEWEB)

    Jones, A. [UT MD Anderson Cancer Center (United States)

    2015-06-15

    With the current Maintenance of Certification (MOC) requirement for a practice quality improvement (PQI) project every 3 years, we all (well, most of us) find ourselves searching for projects that are both manageable and likely to have a positive impact on our clinical practice. In this session we will walk through the use of the Plan, Do, Study, Act (PDSA) cycle to address a common finding in practices where fluoroscopically guided interventions (FGI) are performed: variation in procedural doses among physicians. We will also examine strategies to secure physician support using carrots, not sticks. Learning Objectives: Review the PDSA cycle and its application to PQI. Discuss strategies for action in the example presented. Examine strategies for successful group PQI projects. A. Kyle Jones: Owner, FluoroSafety Joseph R. Steele: Consultant, FluoroSafety.

  5. MO-F-304-01: Applying PDSA to a Practical Clinical Problem: Variation in Procedural Doses Among Interventional Radiologists

    International Nuclear Information System (INIS)

    Jones, A.

    2015-01-01

    With the current Maintenance of Certification (MOC) requirement for a practice quality improvement (PQI) project every 3 years, we all (well, most of us) find ourselves searching for projects that are both manageable and likely to have a positive impact on our clinical practice. In this session we will walk through the use of the Plan, Do, Study, Act (PDSA) cycle to address a common finding in practices where fluoroscopically guided interventions (FGI) are performed: variation in procedural doses among physicians. We will also examine strategies to secure physician support using carrots, not sticks. Learning Objectives: Review the PDSA cycle and its application to PQI. Discuss strategies for action in the example presented. Examine strategies for successful group PQI projects. A. Kyle Jones: Owner, FluoroSafety Joseph R. Steele: Consultant, FluoroSafety

  6. THE VALUE OF REMOVING DAILY OBSTACLES VIA EVERYDAY PROBLEM SOLVING THEORY: DEVELOPING AN APPLIED NOVEL PROCEDURE TO INCREASE SELF-EFFICACY FOR EXERCISE

    Directory of Open Access Journals (Sweden)

    Daniele eArtistico

    2013-01-01

    Full Text Available The objective of the study was to develop a novel procedure to increase self-efficacy for exercise. Gains in one’s ability to resolve day-to-day obstacles for entering an exercise routine were expected to cause an increase in self-efficacy for exercise. Fifty-five sedentary participants (did not exercise regularly for at least 4 months prior to the study who expressed an intention to exercise in the near future were selected for the study. Participants were randomly assigned to one of three conditions: 1 an Experimental Group in which they received a problem-solving training session to learn new strategies for solving day-to-day obstacles that interfere with exercise, 2 a Control Group with Problem Solving Training which received a problem solving training session focused on a typical day-to-day problem unrelated to exercise, or 3 a Control Group which did not receive any problem-solving training. Assessment of obstacles to exercise and perceived self-efficacy for exercise were conducted at baseline; perceived self-efficacy for exercise was reassessed post-intervention (one week later. No differences in perceived challenges posed by obstacles to exercise or self-efficacy for exercise were observed across groups at baseline. The Experimental Group reported greater improvement in self-efficacy for exercise compared to the Control Group with Training (p < 0.01 and the Control Group (p < 0.01. Results of this study suggest that a novel procedure that focuses on removing obstacles to intended planned fitness activities is effective in increasing self-efficacy to engage in exercise among sedentary adults. Implications of these findings for use in applied settings and treatment studies are discussed.

  7. The Value of Removing Daily Obstacles via Everyday Problem-Solving Theory: Developing an Applied Novel Procedure to Increase Self-Efficacy for Exercise.

    Science.gov (United States)

    Artistico, Daniele; Pinto, Angela Marinilli; Douek, Jill; Black, Justin; Pezzuti, Lina

    2013-01-01

    The objective of the study was to develop a novel procedure to increase self-efficacy for exercise. Gains in one's ability to resolve day-to-day obstacles for entering an exercise routine were expected to cause an increase in self-efficacy for exercise. Fifty-five sedentary participants (did not exercise regularly for at least 4 months prior to the study) who expressed an intention to exercise in the near future were selected for the study. Participants were randomly assigned to one of three conditions: (1) an Experimental Group in which they received a problem-solving training session to learn new strategies for solving day-to-day obstacles that interfere with exercise, (2) a Control Group with Problem-Solving Training which received a problem-solving training session focused on a typical day-to-day problem unrelated to exercise, or (3) a Control Group which did not receive any problem-solving training. Assessment of obstacles to exercise and perceived self-efficacy for exercise were conducted at baseline; perceived self-efficacy for exercise was reassessed post-intervention (1 week later). No differences in perceived challenges posed by obstacles to exercise or self-efficacy for exercise were observed across groups at baseline. The Experimental Group reported greater improvement in self-efficacy for exercise compared to the Control Group with Training and the Control Group. Results of this study suggest that a novel procedure that focuses on removing obstacles to intended planned fitness activities is effective in increasing self-efficacy to engage in exercise among sedentary adults. Implications of these findings for use in applied settings and treatment studies are discussed.

  8. Numerical procedure for determining pressure limits on borehole instability problems; Procedimento numerico para determimacao dos limites de pressao em problemas de instabilidade de pocos de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Muller, A.L. [Pontificia Univ. Catolica do Rio de Janeiro (PUC-Rio), RJ (Brazil). Grupo de Tecnologia em Computacao Grafica (TecGraf); Vargas Junior, E.A. [Pontificia Univ. Catolica do Rio de Janeiro (PUC-Rio), RJ (Brazil). Dept. de Engenharia Civil; Vaz, L.E. [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Escola de Engenharia. Dept. de Mecanica Aplicada e Estruturas; Goncalves, C.J. [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES)

    2008-07-01

    In the boreholes projects, the minimization of the instability problems is extreme importance. In the boreholes instability analysis, two failure mechanisms are generally considered, namely, failure due to either tensile or compressive stresses. Considering these mechanisms, the correct determination of the lower and upper limits of pressures, generated by the drilling fluid in the walls of the boreholes, is an alternative for minimization of the instability problems. The mechanisms of compression or tensile failure can be described in terms of mechanical and fluid flow responses of the transient fluid mechanical coupling problem. This paper proposes a numerical procedure, using finite elements, of the coupled fluid mechanical processes, for automatically determining the lower and upper limits of pressures on the walls of borehole, to ensure, according assumptions and criteria of failure pre-established, the stability of the same. The automatic obtaining those values has the purpose of replace the approximate obtaining by trial and error processes. A hypothetical example of application is show, and from this, inferred considerations about the proposed procedure. (author)

  9. MISTRA facility for containment lumped parameter and CFD codes validation. Example of the International Standard Problem ISP47

    International Nuclear Information System (INIS)

    Tkatschenko, I.; Studer, E.; Paillere, H.

    2005-01-01

    During a severe accident in a Pressurized Water Reactor (PWR), the formation of a combustible gas mixture in the complex geometry of the reactor depends on the understanding of hydrogen production, the complex 3D thermal-hydraulics flow due to gas/steam injection, natural convection, heat transfer by condensation on walls and effect of mitigation devices. Numerical simulation of such flows may be performed either by Lumped Parameter (LP) or by Computational Fluid Dynamics (CFD) codes. Advantages and drawbacks of LP and CFD codes are well-known. LP codes are mainly developed for full size containment analysis but they need improvements, especially since they are not able to accurately predict the local gas mixing within the containment. CFD codes require a process of validation on well-instrumented experimental data before they can be used with a high degree of confidence. The MISTRA coupled effect test facility has been built at CEA to fulfil this validation objective: with numerous measurement points in the gaseous volume - temperature, gas concentration, velocity and turbulence - and with well controlled boundary conditions. As illustration of both experimental and simulation areas of this topic, a recent example in the use of MISTRA test data is presented for the case of the International Standard Problem ISP47. The proposed experimental work in the MISTRA facility provides essential data to fill the gaps in the modelling/validation of computational tools. (author)

  10. Exploration of problem-based learning combined with standardized patient in the teaching of basic science of ophthalmology

    Directory of Open Access Journals (Sweden)

    Jin Yan

    2015-08-01

    Full Text Available AIM:To investigate the effect of problem-based learning(PBLcombined with standardized patient(SPin the teaching of basic science of ophthalmology. METHODS: Sixty-four students of Optometry in grade 2012 were randomly divided into experimental group(n=32and control group(n=32. Traditional teaching method was implemented in control group while PBL combined with SP was applied in experimental group. At the end of term students were interviewed using self-administered questionnaire to obtain their evaluation for teaching effect. Measurement data were expressed as (-overx±s and analyzed by independent samples t test. Enumeration data were analyzed by χ2 test, and PRESULTS:The mean scores of theory test(83.22±3.75and experimental test(94.28±2.20in experimental group were significantly higher than theory test(70.72±3.95and experimental test(85.44±3.52in control group(all PPPCONCLUSION:Using PBL combined with SP teaching mode in basic science of ophthalmology can highly improve learning enthusiasm of students and cultivate self-learning ability of students, practice ability and ability of clinical analysis.

  11. ISP-31 OECD/NEA/CSNI International Standard Problem n.31. Cora-13 experiment on severe fuel damage. Comparison report

    International Nuclear Information System (INIS)

    Firnhaber, M.; Trambauer, K.; Hagen, S.; Hofmann, P.; Schanz, G.; Sepold, L.

    1993-07-01

    The severe fuel damage experiment CORA-13 has been offered as CSNI-International Standard Problem (ISP) No. 31. The out-of-pile experiment CORA-13 was executed in November 1990 at Kernforschungszentrum Karlsruhe. The major objectives of this experiment were to investigate the behavior of PWR fuel elements during early core degradation and fast cooldown due to refill. Measured quantities are boundary conditions, bundle temperatures, hydrogen generation and the final bundle configuration. The ISP was conducted as a blind exercise. Boundary conditions which could not be measured, but which are necessary for simplified test simulation (axial power profile, shroud insulation temperature, bundle refill flow) were estimated using ATHLET-CD. Results to the ISP were submitted by 9 participants using different versions of SCDAP/RELAP5, and codes such as FRAS-SFD, ICARE2, KESS-III, MELCOR. The thermal behavior up to significant oxidation has been predicted quite well by most of the codes. In general, the capability of the codes in calculating the main degradation phenomena has been clearly illustrated and weaknesses concerning the modelling of some degradation processes have been identified. Among the degradation phenomena involved in the test, the more severe limitations concern the UO 2 -ZrO 2 dissolution by molten Zr, the solubility limits in the resulting U-Zr-O mixture and the cladding failure by the molten mixture

  12. Standardization of a Protocol for Obtaining Platelet Rich Plasma from blood Donors; a Tool for Tissue Regeneration Procedures.

    Science.gov (United States)

    Gómez, Lina Andrea; Escobar, Magally; Peñuela, Oscar

    2015-01-01

    To develop a protocol for obtaining autologous platelet rich plasma in healthy individuals and to determine the concentration of five major growth factors before platelet activation. This protocol could be integrated into the guidelines of good clinical practice and research in regenerative medicine. Platelet rich plasma was isolated by centrifugation from 38 healthy men and 42 women ranging from 18 to 59 years old. The platelet count and quantification of growth factors were analyzed in eighty samples, stratified for age and gender of the donor. Analyses were performed using parametric the t-test or Pearson's analysis for non-parametric distribution. P platelet counts from 1.6 to 4.9 times (mean = 2.8). There was no correlation between platelet concentration and the level of the following growth factors: VEGF-D (r = 0.009, p = 0.4105), VEGF-A (r = 0.0068, p = 0.953), PDGF subunit AA (p = 0.3618; r = 0.1047), PDGF-BB (p = 0.5936; r = 0.6095). In the same way, there was no correlation between donor gender and growth factor concentrations. Only TGF-β concentration was correlated to platelet concentration (r = 0.3163, p = 0.0175). The procedure used allowed us to make preparations rich in platelets, low in leukocytes and red blood cells, and sterile. Our results showed biological variations in content of growth factors in PRP. The factors influencing these results should be further studied.

  13. Evaluation and assessment methodology, standards, and procedures manual of the United States Federal Radiological Monitoring and Assessment Center

    International Nuclear Information System (INIS)

    Kerns, K.C.; Burson, Z.G.; Smith, J.M.; Blanchard, R.L.

    2000-01-01

    In the event of a major radiological emergency, the U.S. Federal Radiological Emergency Response Plan authorises the creation of the Federal Radiological Monitoring and Assessment Center (FRMAC). The FRMAC is established to co-ordinate the Federal off-site monitoring and assessment activities, and is comprised of representatives from several Federal agencies and Department of Energy contractors who provide assistance to the state(s) and Lead Federal Agency. The Evaluation and Assessment (E and A) Division of the FRMAC is responsible for receiving, storing, and interpreting environmental surveillance data to estimate the potential health consequences to the population in the vicinity of the accident site. The E and A Division has commissioned the preparation of a methodology and procedures manual which will result in a consistent approach by Division members in carrying out their duties. The first edition of this manual is nearing completion. In this paper, a brief review of the structure of the FRMAC is presented, with emphasis on the E and A Division. The contents of the E and A manual are briefly described, as are future plans for its expansion. (author)

  14. International Cooperation to Establish Standard Operating Procedure (SOP) for Quarantine Management of Irradiated Foods in International Trade

    Energy Technology Data Exchange (ETDEWEB)

    Lee, J. W.; Byun, M. W.; Kim, J. H.; Choi, J. I.; Song, B. S.; Yoon, Y. H.; Kim, D. H.; Kim, W. G.; Kim, K. P.

    2010-02-15

    {center_dot} Development of SOPs through various research activities such as building international cooperation, and analysing current status of food irradiation in domestic and international markets, export and import, international market size, and of R and D - Analysis of examples for quarantine management in agricultural product exporting countries and use of irradiation technology for agricultural product quarantine, and changes in international quarantine management - Analysis of SOPs for food irradiation quarantine in international organization (CODEX, IPPC, WHO). U.S, EU, China, India, and Australia. - Collaborative researches of India/Korea and China/Korea entered into an agreement for market trials {center_dot} Publishment of irradiation quarantine management SOPs agreed to CODEX standards - Collaborative researches for quarantine management, avoiding Technical Barrier to Trade (TBT), and Sanitary Phytosanitary Measures were conducted, and advanced SOPs agreed with WTO/FTA system were published

  15. International Cooperation to Establish Standard Operating Procedure (SOP) for Quarantine Management of Irradiated Foods in International Trade

    International Nuclear Information System (INIS)

    Lee, J. W.; Byun, M. W.; Kim, J. H.; Choi, J. I.; Song, B. S.; Yoon, Y. H.; Kim, D. H.; Kim, W. G.; Kim, K. P.

    2010-02-01

    · Development of SOPs through various research activities such as building international cooperation, and analysing current status of food irradiation in domestic and international markets, export and import, international market size, and of R and D - Analysis of examples for quarantine management in agricultural product exporting countries and use of irradiation technology for agricultural product quarantine, and changes in international quarantine management - Analysis of SOPs for food irradiation quarantine in international organization (CODEX, IPPC, WHO). U.S, EU, China, India, and Australia. - Collaborative researches of India/Korea and China/Korea entered into an agreement for market trials · Publishment of irradiation quarantine management SOPs agreed to CODEX standards - Collaborative researches for quarantine management, avoiding Technical Barrier to Trade (TBT), and Sanitary Phytosanitary Measures were conducted, and advanced SOPs agreed with WTO/FTA system were published

  16. Balancing energy conservation and occupant needs in ventilation rate standards for Big Box stores and other commercial buildings in California. Issues related to the ASHRAE 62.1 Indoor Air Quality Procedure

    Energy Technology Data Exchange (ETDEWEB)

    Mendell, Mark J. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Apte, Mike G. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2010-10-31

    This report considers the question of whether the California Energy Commission should incorporate the ASHRAE 62.1 ventilation standard into the Title 24 ventilation rate (VR) standards, thus allowing buildings to follow the Indoor Air Quality Procedure. This, in contrast to the current prescriptive standard, allows the option of using ventilation rate as one of several strategies, which might include source reduction and air cleaning, to meet specified targets of indoor air concentrations and occupant acceptability. The research findings reviewed in this report suggest that a revised approach to a ventilation standard for commercial buildings is necessary, because the current prescriptive ASHRAE 62.1 Ventilation Rate Procedure (VRP) apparently does not provide occupants with either sufficiently acceptable or sufficiently healthprotective air quality. One possible solution would be a dramatic increase in the minimum ventilation rates (VRs) prescribed by a VRP. This solution, however, is not feasible for at least three reasons: the current need to reduce energy use rather than increase it further, the problem of polluted outdoor air in many cities, and the apparent limited ability of increasing VRs to reduce all indoor airborne contaminants of concern (per Hodgson (2003)). Any feasible solution is thus likely to include methods of pollutant reduction other than increased outdoor air ventilation; e.g., source reduction or air cleaning. The alternative 62.1 Indoor Air Quality Procedure (IAQP) offers multiple possible benefits in this direction over the VRP, but seems too limited by insufficient specifications and inadequate available data to provide adequate protection for occupants. Ventilation system designers rarely choose to use it, finding it too arbitrary and requiring use of much non-engineering judgment and information that is not readily available. This report suggests strategies to revise the current ASHRAE IAQP to reduce its current limitations. These

  17. A parallel finite element procedure for contact-impact problems using edge-based smooth triangular element and GPU

    Science.gov (United States)

    Cai, Yong; Cui, Xiangyang; Li, Guangyao; Liu, Wenyang

    2018-04-01

    The edge-smooth finite element method (ES-FEM) can improve the computational accuracy of triangular shell elements and the mesh partition efficiency of complex models. In this paper, an approach is developed to perform explicit finite element simulations of contact-impact problems with a graphical processing unit (GPU) using a special edge-smooth triangular shell element based on ES-FEM. Of critical importance for this problem is achieving finer-grained parallelism to enable efficient data loading and to minimize communication between the device and host. Four kinds of parallel strategies are then developed to efficiently solve these ES-FEM based shell element formulas, and various optimization methods are adopted to ensure aligned memory access. Special focus is dedicated to developing an approach for the parallel construction of edge systems. A parallel hierarchy-territory contact-searching algorithm (HITA) and a parallel penalty function calculation method are embedded in this parallel explicit algorithm. Finally, the program flow is well designed, and a GPU-based simulation system is developed, using Nvidia's CUDA. Several numerical examples are presented to illustrate the high quality of the results obtained with the proposed methods. In addition, the GPU-based parallel computation is shown to significantly reduce the computing time.

  18. Powered bone marrow biopsy procedures produce larger core specimens, with less pain, in less time than with standard manual devices

    Directory of Open Access Journals (Sweden)

    Larry J. Miller

    2011-07-01

    Full Text Available Bone marrow sampling remains essential in the evaluation of hematopoietic and many non-hematopoietic disorders. One common limitation to these procedures is the discomfort experienced by patients. To address whether a Powered biopsy system could reduce discomfort while providing equivalent or better results, we performed a randomized trial in adult volunteers. Twenty-six subjects underwent bilateral biopsies with each device. Core samples were obtained in 66.7% of Manual insertions; 100% of Powered insertions (P=0.002. Initial mean biopsy core lengths were 11.1±4.5 mm for the Manual device; 17.0±6.8 mm for the Powered device (P<0.005. Pathology assessment for the Manual device showed a mean length of 6.1±5.6 mm, width of 1.0±0.7 mm, and volume of 11.0±10.8 mm3. Powered device measurements were mean length of 15.3±6.1 mm, width of 2.0±0.3 mm, and volume of 49.1±21.5 mm3 (P<0.001. The mean time to core ejection was 86 seconds for Manual device; 47 seconds for the Powered device (P<0.001. The mean second look overall pain score was 33.3 for the Manual device; 20.9 for the Powered (P=0.039. We conclude that the Powered biopsy device produces superior sized specimens, with less overall pain, in less time.

  19. Mutagenic treatments towards increasing the frequency of day-neutral mutations and standardization of procedures for tissue culture, in potato

    International Nuclear Information System (INIS)

    Upadhya, M.D.; Chandra, R.; Abraham, M.J.

    1976-01-01

    Various chemical mutagens and gamma radiation have been used on single dormant eyes and true seeds with a view to finding effective mutagenic treatment for the induction of day-length neutral mutants in potato using an effective screening technique for the isolation of day-length neutral mutants. Sodium meta bisulphite (SMS) was found to be an efficient mutagen in inducing mutations for this trait in true seeds although the same concentrations, when used for treating the single tuber eyes proved lethal. Pre-soaking the seeds for 24 hrs prior to treatment with 0.0025M SMS gave highest frequency of the mutants followed by 48 hrs presoaking, indicating a sensitive stage during the cell cycle in true seeds. Other mutagen treatments gave different frequencies of mutations. The highest frequency of day-length neutral mutants was observed when seeds irradiated with 40 Kr of gamma radiation were treated with 0.05M hydrazinium dichloride solution. Screening procedures have also been standardised with the development of synethetic media for the isolation of biochemical mutants at the true seed level. Initial efforts have yielded mutants resistant to LD 100 doses of ethionine. Another aspect of the study was to develop a proper potato callus culture technique. A medium has been developed to produce and maintain callus from potato leaf strips. Efforts on the regeneration of shoot and roots from callus, have so far lead to differentiation of callus to form roots. The ultimate aim of these studies is to develop plantlets from single cell which would form the units of mutation induction and isolation. (author)

  20. Standardization of a rearing procedure of Tetranychus urticae Koch (Acari: Tetranychidae) on bean (Phaseolus vulgaris): plant age and harvest time

    International Nuclear Information System (INIS)

    Bustos, Alexander; Cantor, Fernando; Cure, Jose R; Rodriguez, Daniel

    2009-01-01

    A rearing technique was standardized to produce Tetranychus urticae Koch on Phaseolus vulgaris (ICA Cerinza variety) as a prey of the predatory mite Phytoseiulus persimilis Athias-Henriot. Two assays were conducted to assess the following variables: the most suitable plant age for mite infestation, and the best time to harvest the mites and re infest the plants. In the first experiment, four, five, six, and seven-week-old plants of P. vulgaris were infested with six T. urticae per foliole. The lower plant stratum exhibited the largest number of mites regardless of plant age. However, four-week old plants had the larger average number of individuals. In the second experiment four-week-old plants were infested with 0.5 female mite/cm 2 of leaf. The number of individuals per instar of T. urticae was recorded weekly. The highest mite production occurred between four and five weeks after infestation, indicating this to be the most suitable for mite harvesting and for plant reinfestation. (author)

  1. Philosophy, policy and procedures of the World Organisation for Animal Health for the development of standards in animal welfare.

    Science.gov (United States)

    Petrini, A; Wilson, D

    2005-08-01

    Animal welfare was identified as a priority for the World Organisation for Animal Health (OIE) in the 2001-2005 OIE Strategic Plan. Member Countries recognised that, as animal protection is a complex, multi-faceted public policy issue which includes important scientific, ethical, economic and political dimensions, the OIE needed to develop a detailed vision and strategy incorporating and balancing these dimensions. A permanent working group on animal welfare was established in order to provide guidance to the OIE in its work on the development of science-based standards and guidelines. The Working Group decided to give priority to the welfare of animals used in agriculture and aquaculture, and that, within those groups, the topics of transportation, slaughter for human consumption and killing for disease control purposes would be addressed first. Some guiding principles were approved by the International Committee of OIE Member Countries during the 72nd General Session in May 2004, and these have been followed by four specific guidelines on the priority topics listed above.

  2. Preparation procedure and certification of uranous-uranic oxide and nitric acid solution of neptunium as standard specimens of plant

    International Nuclear Information System (INIS)

    Bulyanitsa, L.S.; Lipovskij, A.A.; Ryzhinskij, M.V.; Preobrazhensskaya, L.D.; Aleksandruk, V.M.; Alekseeva, N.A.; Gromova, E.A.; Solntseva, L.F.; Shereshevskaya, I.I.

    1981-01-01

    Two techniques of certification of standard specimens of plant (SSP) are considered. The first technique-comparison with initial SS-metallic uranium NBS-960 - is used for certification of uranium. protoxide-oxide. The mass part of the sum of analyzed impurities in prepared initial SS is (8.4+-0.8)x10 -3 %. For certification according to mass uranium part the method of gravimetric potentiometric titration with semiautomatic titrator is used; the mean quadratic deviation of the method is s=0.0002-0.0003, certified value of uranium mass part in SSP (taking account of the error of initial SS) is (84.80+-0.02)%. The second technigue - a simplified circular experiment - is used for certification of SSP-nitric acid solution of neptunium as to Np mass part. Coulometry at controlled potential and coulometry at controlled current and two variants of potentiometric titration are used as certification methods of analysis. Relative mean quadratic deviations of the methods are ssub(r)=0.0014-0.0023. When calculating total error of certified value of neptunium mass part constituents of both accidental and unremoved systematic errors of the methods were included. The final certification result of SSP is (5.707+-0.018)% [ru

  3. Recanalization strategy for chronic total occlusions with tapered and stiff-tip guidewire. The results of CTO new techniQUE for STandard procedure (CONQUEST) trial.

    Science.gov (United States)

    Mitsudo, Kazuaki; Yamashita, Takehiro; Asakura, Yasushi; Muramatsu, Toshiya; Doi, Osamu; Shibata, Yoshisato; Morino, Yoshihiro

    2008-11-01

    The success rate of percutaneous coronary intervention (PCI) for chronic total coronary occlusion (CTO) lesions varies depending on the guidewire manipulation skills of the operator. The standardization of guidewire technique is very important. A new technique with a new tapered wire (Conquest, Confianza Pro) was tested to verify effectiveness for higher initial success rates and standardization of PCI for CTO. A prospective, multicenter registry was conducted at 6 investigational sites. In the CONQUEST trial, The CTO lesions were treated by using an intermediate guidewire to cross the lesion. If it did not cross, the guidewire was changed to the Conquest guidewire. If it did not cross, "seesaw-wiring" or the "parallel-wire technique" was performed. The primary endpoint was the initial procedural success rate. A total of 110 patients representing 116 CTO lesions were treated from July 2003 through March 2004. The procedural success rate was 86.2% on the first try, and 88.8% on the second try, respectively. The guidewire success rate on the second try was 90.5% during the hospital stay; no deaths, or acute myocardial infarctions were confirmed. Two patients deteriorated into tamponade, and surgical or percutaneous drainage was performed in each patient without any sequelae. A guidewire technique in PCI for CTOs that starts with the intermediate guidewire and moves to the Confianza Pro tapered guidewire, either alone or by performing a see-saw or parallel-wire technique, can achieve a high initial success rate with an acceptably low major complication rate.

  4. [Advantages and disadvantages of different methods for the implementation and the support of standard operating procedures: From PDF files to an app- and webbased SOP management system].

    Science.gov (United States)

    Bauer, M; Riech, S; Brandes, I; Waeschle, R M

    2015-11-01

    The quality assurance of care and patient safety, with increasing cost pressure and performance levels is of major importance in the high-risk and high cost area of the operating room (OR). Standard operating procedures (SOP) are an established tool for structuring and standardization of the clinical treatment pathways and show multiple benefits for quality assurance and process optimization. An internal project was initiated in the department of anesthesiology and a continuous improvement process was carried out to build up a comprehensive SOP library. In the first step the spectrum of procedures in anesthesiology was transferred to PDF-based SOPs. The further development to an app-based SOP library (Aesculapp) was due to the high resource expenditure for the administration and maintenance of the large PDF-based SOP collection and to deficits in the mobile availability. The next developmental stage, the SOP healthcare information assistant (SOPHIA) included a simplified and advanced update feature, an archive feature previously missing and notably the possibility to share the SOP library with other departments including the option to adapt each SOP to the individual situation. A survey of the personnel showed that the app-based allocation of SOPs (Aesculapp, SOPHIA) had a higher acceptance than the PDF-based developmental stage SOP form. The SOP management system SOPHIA combines the benefits of the forerunner version Aesculapp with improved options for intradepartmental maintenance and administration of the SOPs and the possibility of an export and editing function for interinstitutional exchange of SOPs.

  5. [Evaluation of selected parameters of blood coagulation and fibrinolysis system in patients undergoing total hip replacement surgery with normovolemic hemodilution procedure and standard enoxaparine prophylaxis].

    Science.gov (United States)

    Piecuch, Wiesław; Sokołowska, Bozena; Dmoszyńska, Anna; Furmanik, Franciszek

    2003-01-01

    The aim of the study was to evaluate selected blood coagulation and fibrinolysis parameters in patients undergoing total hip replacement surgery with normovolemic hemodilution and standard enoksaparine profilaxis. The study included 66 patients undergoing hip replacement surgery. The group consisted of 51 women and 15 men, within the age range of 47-78, the mean age was 64. In 32 (subgroup II) patients the surgery was performed with the use of normovolemic hemodilution, in 34 (subgroup I) the hemodilution procedure was not applied. The enoksaparine as prophylaxis started 12 hours prior to surgery and continued during hospitalisation. The examination of the coagulation system was performed: on the day of the operation in the morning, on the day of the operation in the evening and on the first day after operation. We determined the concentrations of TAT and PAP complexes, prothrombin fragments 1 + 2 (F1 + 2) and d-dimers (DD). 1) during total hip replacement surgery and particularly in the period of the first 12 hours after the procedure marked activation of coagulation and fibrinolysis occurRed; 2) the application of the hemodilution procedure does not influence significantly the degree of coagulation and fibrinolysis disorders in the perioperative period, but could reduced incidence of thromboembolic complications in the postoperative period.

  6. The CSNI International Standard Problem Programme: Overall Presentation on Objectives; Rationale and Lessons Learnt: a Joint Venture of the Thermalhydraulic International Community

    International Nuclear Information System (INIS)

    Reocreux, M.

    2008-01-01

    The CSNI International Standard Problems have been one of the key activities of the CSNI thermal hydraulics groups during the last 25 years. After recalling the way the international standard problems were initiated in the late 1970 years -they were called at that time CSNI LOCA Standard Problem- the process which has led to make from the ISPs a full CSNI activity, is described. Rules have been defined which formalized the way experimental results were provided and the way the comparison exercise were performed. The long series of ISPs from 1975 up to nowadays is described, explaining the different trends in the ISPs choices. The findings which have been obtained are reviewed on both technical and programmatic aspects.

  7. International standard problem ISP36. Cora-W2 experiment on severe fuel damage for a Russian type PWR

    International Nuclear Information System (INIS)

    1996-01-01

    An OECD/NEA-CSNI International Standard Problem (ISP) has been performed on the experimental comparison basis of the severe fuel damage experiment CORA-W2. The out-of-pile experiment CORA-W2 was executed in February 1993 at he Forschungszentrum Karlsruhe. The objective of this experiment was the investigation of the behavior of a Russian type PWR fuel element (VVER-1000) during early core degradation. The main difference between a Western type and a Russian type PWR bundle is the B 4 C absorber rod instead of AgInCd. Measured quantities ar boundary conditions, bundle temperature, hydrogen generation and the final bundle configurations after cooldown. The ISP was conducted as a blind exercise. Boundary conditions were estimated using ATHLET-CD. Six different severe accident codes were used. The comparisons between experimental and analytical results were grouped by codes and examined separately. The thermal behavior up to significant oxidation has been predicted quite well. Larger deviations have been observed for the oxidation-induced temperature escalation, both time of onset and maximum temperature as well. The bundle behavior is greatly influenced by chemical interactions involving B 4 C absorber rod material, which failed relatively early at low temperature due to eutectic interaction between B 4 C and SS cladding as well as the SS guide tube. Regarding the complex material interaction larger differences can be recognized between calculated and measured results because of inappropriate models for material relocation and solidification processes and the lack of models describing the interactions of absorber rod materials with the fuel rods. For the total amount of H 2 generated, acceptable agreement could be achieved, if the total of oxidized zirconium was calculated correctly. The oxidation of stainless steel components and B 4 C were not treated. In general the confidence in code predictions decreases with processing core damage. (N.T.)

  8. International standard problem ISP36. Cora-W2 experiment on severe fuel damage for a Russian type PWR

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-31

    An OECD/NEA-CSNI International Standard Problem (ISP) has been performed on the experimental comparison basis of the severe fuel damage experiment CORA-W2. The out-of-pile experiment CORA-W2 was executed in February 1993 at he Forschungszentrum Karlsruhe. The objective of this experiment was the investigation of the behavior of a Russian type PWR fuel element (VVER-1000) during early core degradation. The main difference between a Western type and a Russian type PWR bundle is the B{sub 4}C absorber rod instead of AgInCd. Measured quantities ar boundary conditions, bundle temperature, hydrogen generation and the final bundle configurations after cooldown. The ISP was conducted as a blind exercise. Boundary conditions were estimated using ATHLET-CD. Six different severe accident codes were used. The comparisons between experimental and analytical results were grouped by codes and examined separately. The thermal behavior up to significant oxidation has been predicted quite well. Larger deviations have been observed for the oxidation-induced temperature escalation, both time of onset and maximum temperature as well. The bundle behavior is greatly influenced by chemical interactions involving B{sub 4}C absorber rod material, which failed relatively early at low temperature due to eutectic interaction between B{sub 4}C and SS cladding as well as the SS guide tube. Regarding the complex material interaction larger differences can be recognized between calculated and measured results because of inappropriate models for material relocation and solidification processes and the lack of models describing the interactions of absorber rod materials with the fuel rods. For the total amount of H{sub 2} generated, acceptable agreement could be achieved, if the total of oxidized zirconium was calculated correctly. The oxidation of stainless steel components and B{sub 4}C were not treated. In general the confidence in code predictions decreases with processing core damage. 36 refs.

  9. When one size does not fit all : A problem of fit rather than failure for voluntary management standards

    NARCIS (Netherlands)

    Simpson, Dayna; Power, Damien; Klassen, Robert

    Voluntary management standards for social and environmental performance ideally help to define and improve firms' related capabilities. These standards, however, have largely failed to improve such performance as intended. Over-emphasis on institutional factors leading to adoption of these standards

  10. Drowning - a scientometric analysis and data acquisition of a constant global problem employing density equalizing mapping and scientometric benchmarking procedures

    Directory of Open Access Journals (Sweden)

    Groneberg David A

    2011-10-01

    Full Text Available Abstract Background Drowning is a constant global problem which claims approximately half a million victims worldwide each year, whereas the number of near-drowning victims is considerably higher. Public health strategies to reduce the burden of death are still limited. While research activities in the subject drowning grow constantly, yet there is no scientometric evaluation of the existing literature at the present time. Methods The current study uses classical bibliometric tools and visualizing techniques such as density equalizing mapping to analyse and evaluate the scientific research in the field of drowning. The interpretation of the achieved results is also implemented in the context of the data collection of the WHO. Results All studies related to drowning and listed in the ISI-Web of Science database since 1900 were identified using the search term "drowning". Implementing bibliometric methods, a constant increase in quantitative markers such as number of publications per state, publication language or collaborations as well as qualitative markers such as citations were observed for research in the field of drowning. The combination with density equalizing mapping exposed different global patterns for research productivity and the total number of drowning deaths and drowning rates respectively. Chart techniques were used to illustrate bi- and multilateral research cooperation. Conclusions The present study provides the first scientometric approach that visualizes research activity on the subject of drowning. It can be assumed that the scientific approach to this topic will achieve even greater dimensions because of its continuing actuality.

  11. Drowning - a scientometric analysis and data acquisition of a constant global problem employing density equalizing mapping and scientometric benchmarking procedures

    Science.gov (United States)

    2011-01-01

    Background Drowning is a constant global problem which claims approximately half a million victims worldwide each year, whereas the number of near-drowning victims is considerably higher. Public health strategies to reduce the burden of death are still limited. While research activities in the subject drowning grow constantly, yet there is no scientometric evaluation of the existing literature at the present time. Methods The current study uses classical bibliometric tools and visualizing techniques such as density equalizing mapping to analyse and evaluate the scientific research in the field of drowning. The interpretation of the achieved results is also implemented in the context of the data collection of the WHO. Results All studies related to drowning and listed in the ISI-Web of Science database since 1900 were identified using the search term "drowning". Implementing bibliometric methods, a constant increase in quantitative markers such as number of publications per state, publication language or collaborations as well as qualitative markers such as citations were observed for research in the field of drowning. The combination with density equalizing mapping exposed different global patterns for research productivity and the total number of drowning deaths and drowning rates respectively. Chart techniques were used to illustrate bi- and multilateral research cooperation. Conclusions The present study provides the first scientometric approach that visualizes research activity on the subject of drowning. It can be assumed that the scientific approach to this topic will achieve even greater dimensions because of its continuing actuality. PMID:21999813

  12. Mathematical problem solving in primary school

    NARCIS (Netherlands)

    Kolovou, A.

    2011-01-01

    A student is engaged in (non-routine) problem solving when there is no clear pathway to the solution. In contrast to routine problems, non-routine ones cannot be solved through the direct application of a standard procedure. Consider the following problem: In a quiz you get two points for each

  13. Application of NEA/CSNI standard problem 3 (blowdown and flow reversal in the IETA-1 rig) to the validation of the RELAP-UK Mk IV code

    International Nuclear Information System (INIS)

    Bryce, W.M.

    1977-10-01

    NEA/CSNI Standard Problem 3 consists of the modelling of an experiment on the IETI-1 rig, in which there is initially flow upwards through a feeder, heated section and riser. The inlet and outlet are then closed and a breach opened at the bottom so that the flow reverses and the rig depressurises. Calculations of this problem by many countries using several computer codes have been reported and show a wide spread of results. The purpose of the study reported here was the following. First, to show the sensitivity of the calculation of Standard Problem 3. Second, to perform an ab initio best estimate calculation using the RELAP-UK Mark IV code with the standard recommended options, and third, to use the results of the sensitivity study to show where tuning of the RELAP-UK Mark IV recommended model options was required. This study has shown that the calculation of Standard Problem 3 is sensitive to model assumptions and that the use of the loss-of-coolant accident code RELAP-UK Mk IV with the standard recommended model options predicts the experimental results very well over most of the transient. (U.K.)

  14. A synergetic combination of small and large neighborhood schemes in developing an effective procedure for solving the job shop scheduling problem.

    Science.gov (United States)

    Amirghasemi, Mehrdad; Zamani, Reza

    2014-01-01

    This paper presents an effective procedure for solving the job shop problem. Synergistically combining small and large neighborhood schemes, the procedure consists of four components, namely (i) a construction method for generating semi-active schedules by a forward-backward mechanism, (ii) a local search for manipulating a small neighborhood structure guided by a tabu list, (iii) a feedback-based mechanism for perturbing the solutions generated, and (iv) a very large-neighborhood local search guided by a forward-backward shifting bottleneck method. The combination of shifting bottleneck mechanism and tabu list is used as a means of the manipulation of neighborhood structures, and the perturbation mechanism employed diversifies the search. A feedback mechanism, called repeat-check, detects consequent repeats and ignites a perturbation when the total number of consecutive repeats for two identical makespan values reaches a given threshold. The results of extensive computational experiments on the benchmark instances indicate that the combination of these four components is synergetic, in the sense that they collectively make the procedure fast and robust.

  15. Inverse modeling for seawater intrusion in coastal aquifers: Insights about parameter sensitivities, variances, correlations and estimation procedures derived from the Henry problem

    Science.gov (United States)

    Sanz, E.; Voss, C.I.

    2006-01-01

    Inverse modeling studies employing data collected from the classic Henry seawater intrusion problem give insight into several important aspects of inverse modeling of seawater intrusion problems and effective measurement strategies for estimation of parameters for seawater intrusion. Despite the simplicity of the Henry problem, it embodies the behavior of a typical seawater intrusion situation in a single aquifer. Data collected from the numerical problem solution are employed without added noise in order to focus on the aspects of inverse modeling strategies dictated by the physics of variable-density flow and solute transport during seawater intrusion. Covariances of model parameters that can be estimated are strongly dependent on the physics. The insights gained from this type of analysis may be directly applied to field problems in the presence of data errors, using standard inverse modeling approaches to deal with uncertainty in data. Covariance analysis of the Henry problem indicates that in order to generally reduce variance of parameter estimates, the ideal places to measure pressure are as far away from the coast as possible, at any depth, and the ideal places to measure concentration are near the bottom of the aquifer between the center of the transition zone and its inland fringe. These observations are located in and near high-sensitivity regions of system parameters, which may be identified in a sensitivity analysis with respect to several parameters. However, both the form of error distribution in the observations and the observation weights impact the spatial sensitivity distributions, and different choices for error distributions or weights can result in significantly different regions of high sensitivity. Thus, in order to design effective sampling networks, the error form and weights must be carefully considered. For the Henry problem, permeability and freshwater inflow can be estimated with low estimation variance from only pressure or only

  16. Randomized trial of one-hour sodium bicarbonate vs standard periprocedural saline hydration in chronic kidney disease patients undergoing cardiovascular contrast procedures.

    Directory of Open Access Journals (Sweden)

    Judith Kooiman

    Full Text Available Guidelines advise periprocedural saline hydration for prevention of contrast induced-acute kidney injury (CI-AKI. We analysed whether 1-hour sodium bicarbonate hydration administered solely prior to intra-arterial contrast exposure is non-inferior to standard periprocedural saline hydration in chronic kidney disease (CKD patients undergoing elective cardiovascular diagnostic or interventional contrast procedures.We performed an open-label multicentre non-inferiority trial between 2011-2014. Patients were randomized to 1 hour pre-procedure sodium bicarbonate hydration (250 ml 1.4%, N = 168 or 4-12 hours saline hydration (1000 ml 0.9%, N = 165 prior to and following contrast administration (2000 ml of saline total. Primary outcome was the relative serum creatinine increase (% 48-96 hours post contrast exposure. Secondary outcomes were: incidence of CI-AKI (serum creatinine increase>25% or >44μmol/L, recovery of renal function, the need for dialysis, and hospital costs within two months follow-up.Mean relative creatinine increase was 3.1% (95%CI 0.9 to 5.2% in the bicarbonate and 1.1% (95%CI -1.2 to 3.5% in the saline arm, mean difference 1.9% (95%CI -1.2 to 5.1%, p-non-inferiority <0.001. CI-AKI occurred in 11 (6.7% patients randomized to sodium bicarbonate and 12 (7.5% to saline (p = 0.79. Renal function did not fully recover in 40.0% and 44.4% of CI-AKI patients, respectively (p = 0.84. No patient required dialysis. Mean costs for preventive hydration and clinical preparation for the contrast procedure were $1158 for sodium bicarbonate vs. $1561 for saline (p < 0.001.Short hydration with sodium bicarbonate prior to elective cardiovascular diagnostic or therapeutic contrast procedures is non-inferior to standard periprocedural saline hydration in CKD patients with respect to renal safety and results in considerable healthcare savings.Netherlands Trial Register (http://www.trialregister.nl/trialreg/index.asp, Nr NTR2699.

  17. Randomized trial of one-hour sodium bicarbonate vs standard periprocedural saline hydration in chronic kidney disease patients undergoing cardiovascular contrast procedures.

    Science.gov (United States)

    Kooiman, Judith; de Vries, Jean-Paul P M; Van der Heyden, Jan; Sijpkens, Yvo W J; van Dijkman, Paul R M; Wever, Jan J; van Overhagen, Hans; Vahl, Antonie C; Aarts, Nico; Verberk-Jonkers, Iris J A M; Brulez, Harald F H; Hamming, Jaap F; van der Molen, Aart J; Cannegieter, Suzanne C; Putter, Hein; van den Hout, Wilbert B; Kilicsoy, Inci; Rabelink, Ton J; Huisman, Menno V

    2018-01-01

    Guidelines advise periprocedural saline hydration for prevention of contrast induced-acute kidney injury (CI-AKI). We analysed whether 1-hour sodium bicarbonate hydration administered solely prior to intra-arterial contrast exposure is non-inferior to standard periprocedural saline hydration in chronic kidney disease (CKD) patients undergoing elective cardiovascular diagnostic or interventional contrast procedures. We performed an open-label multicentre non-inferiority trial between 2011-2014. Patients were randomized to 1 hour pre-procedure sodium bicarbonate hydration (250 ml 1.4%, N = 168) or 4-12 hours saline hydration (1000 ml 0.9%, N = 165) prior to and following contrast administration (2000 ml of saline total). Primary outcome was the relative serum creatinine increase (%) 48-96 hours post contrast exposure. Secondary outcomes were: incidence of CI-AKI (serum creatinine increase>25% or >44μmol/L), recovery of renal function, the need for dialysis, and hospital costs within two months follow-up. Mean relative creatinine increase was 3.1% (95%CI 0.9 to 5.2%) in the bicarbonate and 1.1% (95%CI -1.2 to 3.5%) in the saline arm, mean difference 1.9% (95%CI -1.2 to 5.1%, p-non-inferiority <0.001). CI-AKI occurred in 11 (6.7%) patients randomized to sodium bicarbonate and 12 (7.5%) to saline (p = 0.79). Renal function did not fully recover in 40.0% and 44.4% of CI-AKI patients, respectively (p = 0.84). No patient required dialysis. Mean costs for preventive hydration and clinical preparation for the contrast procedure were $1158 for sodium bicarbonate vs. $1561 for saline (p < 0.001). Short hydration with sodium bicarbonate prior to elective cardiovascular diagnostic or therapeutic contrast procedures is non-inferior to standard periprocedural saline hydration in CKD patients with respect to renal safety and results in considerable healthcare savings. Netherlands Trial Register (http://www.trialregister.nl/trialreg/index.asp), Nr NTR2699.

  18. Distribution of hydrogen within the HDR-containment under severe accident conditions. OECD standard problem. Final comparison report

    International Nuclear Information System (INIS)

    Karwat, H.

    1992-08-01

    The present report summarizes the results of the International Standard Problem Exercise ISP-29, based on the HDR Hydrogen Distribution Experiment E11.2. Post-test analyses are compared to experimentally measured parameters, well-known to the analysis. This report has been prepared by the Institute for Reactor Dynamics and Reactor Safety of the Technical University Munich under contract with the Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) which received funding for this activity from the German Ministry for Research and Technology (BMFT) under the research contract RS 792. The HDR experiment E11.2 has been performed by the Kernforschungszentrum Karlsruhe (KfK) in the frame of the project 'Projekt HDR-Sicherheitsprogramm' sponsored by the BMFT. Ten institutions from eight countries participated in the post-test analysis exercise which was focussing on the long-lasting gas distribution processes expected inside a PWR containment under severe accident conditions. The gas release experiment was coupled to a long-lasting steam release into the containment typical for an unmitigated small break loss-of-coolant accident. In lieu of pure hydrogen a gas mixture consisting of 15% hydrogen and 85% helium has been applied in order to avoid reaching flammability during the experiment. Of central importance are common overlay plots comparing calculated transients with measurements of the global pressure, the local temperature-, steam- and gas concentration distributions throughout the entire HDR containment. The comparisons indicate relatively large margins between most calculations and the experiment. Having in mind that this exercise was specified as an 'open post-test' analysis of well-known measured data the reasons for discrepancies between measurements and simulations were extensively discussed during a final workshop. It was concluded that analytical shortcomings as well as some uncertainties of experimental boundary conditions may be responsible for deviations

  19. Distribution of hydrogen within the HDR-containment under severe accident conditions. OECD standard problem. Final comparison report

    Energy Technology Data Exchange (ETDEWEB)

    Karwat, H

    1992-08-15

    The present report summarizes the results of the International Standard Problem Exercise ISP-29, based on the HDR Hydrogen Distribution Experiment E11.2. Post-test analyses are compared to experimentally measured parameters, well-known to the analysis. This report has been prepared by the Institute for Reactor Dynamics and Reactor Safety of the Technical University Munich under contract with the Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) which received funding for this activity from the German Ministry for Research and Technology (BMFT) under the research contract RS 792. The HDR experiment E11.2 has been performed by the Kernforschungszentrum Karlsruhe (KfK) in the frame of the project 'Projekt HDR-Sicherheitsprogramm' sponsored by the BMFT. Ten institutions from eight countries participated in the post-test analysis exercise which was focussing on the long-lasting gas distribution processes expected inside a PWR containment under severe accident conditions. The gas release experiment was coupled to a long-lasting steam release into the containment typical for an unmitigated small break loss-of-coolant accident. In lieu of pure hydrogen a gas mixture consisting of 15% hydrogen and 85% helium has been applied in order to avoid reaching flammability during the experiment. Of central importance are common overlay plots comparing calculated transients with measurements of the global pressure, the local temperature-, steam- and gas concentration distributions throughout the entire HDR containment. The comparisons indicate relatively large margins between most calculations and the experiment. Having in mind that this exercise was specified as an 'open post-test' analysis of well-known measured data the reasons for discrepancies between measurements and simulations were extensively discussed during a final workshop. It was concluded that analytical shortcomings as well as some uncertainties of experimental boundary conditions may be responsible for deviations

  20. Problems of Technical Standards Teaching in the Context of the Globalization and Euro-Integration in Higher Education System of Ukraine

    Science.gov (United States)

    Kornuta, Olena; Pryhorovska, Tetiana

    2015-01-01

    Globalization and Ukraine association with EU imply including Ukrainian universities into the world scientific space. The aim of this article is to analyze the problem of drawing standards teaching, based on the experience of Ivano-Frankivsk National Technical University of Oil and Gas (Ukraine) and to summarize the experience of post Soviet…

  1. Effects of training self-assessment and using assessment standards on retrospective and prospective monitoring of problem solving

    NARCIS (Netherlands)

    Baars, Martine; Vink, Sigrid; van Gog, Tamara; de Bruin, Anique; Paas, Fred

    2014-01-01

    Both retrospective and prospective monitoring are considered important for self-regulated learning of problem-solving skills. Retrospective monitoring (or self-assessment; SA) refers to students' assessments of how well they performed on a problem just completed. Prospective monitoring (or Judgments

  2. Understanding Problem-Solving Errors by Students with Learning Disabilities in Standards-Based and Traditional Curricula

    Science.gov (United States)

    Bouck, Emily C.; Bouck, Mary K.; Joshi, Gauri S.; Johnson, Linley

    2016-01-01

    Students with learning disabilities struggle with word problems in mathematics classes. Understanding the type of errors students make when working through such mathematical problems can further describe student performance and highlight student difficulties. Through the use of error codes, researchers analyzed the type of errors made by 14 sixth…

  3. Evaluation and standardization of different purification procedures for fish bile and liver metallothionein quantification by spectrophotometry and SDS-PAGE analyses.

    Science.gov (United States)

    Tenório-Daussat, Carolina Lyrio; Resende, Marcia Carolina Martinho; Ziolli, Roberta L; Hauser-Davis, Rachel Ann; Schaumloffel, Dirk; Saint'Pierre, Tatiana D

    2014-03-01

    Fish bile metallothioneins (MT) have been recently reported as biomarkers for environmental metal contamination; however, no studies regarding standardizations for their purification are available. Therefore, different procedures (varying centrifugation times and heat-treatment temperatures) and reducing agents (DTT, β-mercaptoethanol and TCEP) were applied to purify MT isolated from fish (Oreochromis niloticus) bile and liver. Liver was also analyzed, since these two organs are intrinsically connected and show the same trend regarding MT expression. Spectrophotometrical analyses were used to quantify the resulting MT samples, and SDS-PAGE gels were used to qualitatively assess the different procedure results. Each procedure was then statistically evaluated and a multivariate statistical analysis was then applied. A response surface methodology was also applied for bile samples, in order to further evaluate the responses for this matrix. Heat treatment effectively removes most undesired proteins from the samples, however results indicate that temperatures above 70 °C are not efficient since they also remove MTs from both bile and liver samples. Our results also indicate that the centrifugation times described in the literature can be decreased in order to analyze more samples in the same timeframe, of importance in environmental monitoring contexts where samples are usually numerous. In an environmental context, biliary MT was lower than liver MT, as expected, since liver accumulates MT with slower detoxification rates than bile, which is released from the gallbladder during feeding, and then diluted by water. Therefore, bile MT seems to be more adequate in environmental monitoring scopes regarding recent exposure to xenobiotics that may affect the proteomic and metalloproteomic expression of this biological matrix. Copyright © 2013 Elsevier B.V. All rights reserved.

  4. International standard problem (ISP) No. 43 Rapid boron-dilution transient tests for code verification. Comparison report

    International Nuclear Information System (INIS)

    2001-03-01

    International Standard Problem No. 43 (ISP 43) addresses the nuclear industries present capabilities of simulating fluid dynamics aspects of a subset of rapid boron dilution transients. Specifically, the exercise focuses on the sequence involving the transport of a boron-dilute slug through the actuation of a pump. The slug is formed on the primary side of the steam generator as a consequence of in interfacing system leak from the secondary un-borated coolant. Experimental data was collected using the University of Maryland 2 x 4 Thermalhydraulic Loop (UM 2 x 4 Loop) and the Boron-mixing Visualization Facility. Two blind test series were proposed during the first workshop (October 1998) and refined using participant input. The first series, test series A, deals with the injection of a front, i.e., a single interface between borated and dilute fluids. The second blind series, test series B, is the more realistic injection of a slug, i.e., a dilute fluid volume preceded and followed by the borated coolant of the primary system. Data are collected in the UM 2 x 4 Loop and refined details are obtained from the Visualization Facility, which represents a replica of the Loop.s vessel downcomer. In the Loop experimental program, the dilute volume is simulated by cold water and the borated primary coolant is simulated by hot water. The Visualization Facility uses dye to mark the diluted front or slug. The measured boundary conditions for both test series include the initial temperature of the primary system, the front/slug injection flowrate and temperature, and the pressure drop across the core. Temperature data is collected at 185 thermocouple positions in the downcomer and 38 positions in the lower plenum. The advancement of the front/slug through the system is monitored at discrete horizontal levels that contain the thermocouples. The performance of codes is measured relative to a set of figures of merit. During the first workshop, the principal figure of merit was

  5. An investigation of pre-activity cardiovascular screening procedures in health/fitness facilities--part II: rationale for low adherence with national standards.

    Science.gov (United States)

    Springer, Judy B; Eickhoff-Shemek, JoAnn M; Zuberbuehler, Ernest J

    2009-01-01

    The purpose of this study was to explore the rationale provided by program directors and general managers of health/fitness facilities for low adherence to nationally accepted standards related to pre-activity cardiovascular screening procedures (PACSPs) for members and clients of personal trainers. Qualitative interviews were conducted with the directors/managers in a Midwest region representing 76 facilities who indicated they did not conduct PACSPs for members and clients of personal trainers. Analysis of the rationale provided revealed 6 major clusters: (1) Purpose or need for screening; (2) time and staffing; (3) barrier to participation; (4) personal responsibility for health and actions; (5) legal issues; and (6) company or franchise policy that categorized the reasons for low adherence to PACSPs. These findings highlight the need to increase awareness of the relevance of PACSPs among health/fitness managers, staff members, and current exercise science students as well as engage those in risk management for informed dialogue for consistent application of the standard of care. Copyright 2009 Wiley Periodicals, Inc.

  6. Update of X ray and gamma ray decay data standards for detector calibration and other applications. V. 2: Data selection, assessment and evaluation procedures

    International Nuclear Information System (INIS)

    2007-05-01

    Various factors such as source preparation and source detector geometry may affect the quality of measurements made with intrinsic germanium and other γ ray spectrometers. However, the accuracy of such measurements invariably depends on the accuracy of the efficiency versus energy calibration curve and hence on the accuracy of the decay data for the radionuclides from which calibration standard sources are prepared. Both half-lives and X and γ ray emission probabilities need to be known to good accuracy. The recommendations and report of this work are published in two volumes: Volume 1 - Recommended Decay Data, High Energy Gamma Ray Standards and Angular Correlation Coefficients; Volume 2 - Data Selection, Assessment and Evaluation Procedures. Volume 1 is a self-contained assembly of the recommended decay data covering half-lives and the X ray and γ ray emission probabilities of the selected radionuclides, and listings of various high energy γ ray standards and a set of angular correlation coefficients; these data are presented in a concise manner for rapid and easy access. More detailed technical features of the CRP are described in Volume 2, including the evaluation procedures adopted and extensive traceable explanations of the origins of the nuclear data used to produce the recommended values listed in Volume 1. This detail was judged to be essential in order to record and demonstrate the quality of the resulting data files and allow the reader to trace the origins of the nuclear data used to determine the recommended values. All evaluations were based on the available experimental data, supplemented with the judicious use of well established theory. Three types of data (half-lives, energies and emission probabilities) were compiled and evaluated (Annex II). Consideration was also given to the adoption of a number of prompt high energy γ rays from specific nuclear reactions (Annex III), as well as to using the γ-γ coincidence technique for efficiency

  7. Procedimientos Comunes de Operacion Para Juntas Responsabilidades y Derechos del Presidente, Vice Presidente, Secretaria, y Miembros (Standard Procedures of Operation for Meetings, Rights, and Responsibilities of the President, Vice President, Secretary, and Members).

    Science.gov (United States)

    Gonzalez, Ramon

    Of use to Parent Advisory Committees, this Spanish-English handout briefly describes the standard procedures used to conduct meetings and outlines the duties of committee officers and members. The pamphlet describes the standard order of business at a meeting, including calling a meeting to order, roll call, minutes, reports, unfinished and new…

  8. Road safety audit tools, procedures, and experiences : a literature review and recommendations : research in the framework of the European research project Safety Standards for Road Design and Redesign SAFESTAR, Workpackage 8.

    NARCIS (Netherlands)

    Kooi, R.M. van der

    1999-01-01

    This report describes tools and procedures established in different countries which apply Road Safety Audits (RSA). These RSAs are utilized to identify potential safety problems and they concentrate on safety measures to overcome these problems. This technique is used to detect possible safety

  9. Multicenter study on costs associated with two surgical procedures: GreenLight XPS 180 W versus the gold standard transurethral resection of the prostate.

    Science.gov (United States)

    Benejam-Gual, J M; Sanz-Granda, A; Budía, A; Extramiana, J; Capitán, C

    2014-01-01

    To analyze the costs associated with two surgical procedures for lower urinary tract symptoms secondary to benign prostatic hyperplasia: GreenLight XPS 180¦W versus the gold standard transurethral resection of the prostate. A multicenter, retrospective cost study was carried out from the National Health Service perspective, over a 3-month time period. Costs were broken down into pre-surgical, surgical and post-surgical phases. Data were extracted from records of patients operated sequentially, with IPSS=15, Qmax=15 mL/seg and a prostate volume of 40-80mL, adding only direct healthcare costs (€, 2013) associated with the procedure and management of complications. A total of 79 patients sequentially underwent GL XPS (n: 39) or TURP (n: 40) between July and October, 2013. Clinical outcomes were similar (94.9% and 92.5%, GL XPS and TURP, respectively) without significant differences (P=.67). The average direct cost per patient was reduced by €114 in GL XPS versus TURP patients; the cost was higher in the surgical phase with GL XPS (difference: €1,209; P<.001) but was lower in the post-surgical phase (difference: €-1,351; P<.001). The GreenLight XPS 180-W laser system is associated with a reduction in costs with respect to transurethral resection of prostate in the surgical treatment of LUTS secondary to PBH. This reduction is due to a shorter inpatient length of stay that offsets the cost of the new technology. Copyright © 2013 AEU. Published by Elsevier Espana. All rights reserved.

  10. An Exploration of the Use of Eye-Gaze Tracking to Study Problem-Solving on Standardized Science Assessments

    Science.gov (United States)

    Tai, Robert H.; Loehr, John F.; Brigham, Frederick J.

    2006-01-01

    This pilot study investigated the capacity of eye-gaze tracking to identify differences in problem-solving behaviours within a group of individuals who possessed varying degrees of knowledge and expertise in three disciplines of science (biology, chemistry and physics). The six participants, all pre-service science teachers, completed an 18-item…

  11. Xeon Phi - A comparison between the newly introduced MIC architecture and a standard CPU through three types of problems.

    OpenAIRE

    Kristiansen, Joakim

    2016-01-01

    As Moore s law continues, processors keep getting more cores packed together on the chip. This thesis is an empirical study of the rather newly introduced Intel Many Integrated Core (IMIC) architecture found in the Intel Xeon Phi. With roughly 60 cores connected by a high performance on-die interconnect, the Intel Xeon Phi makes an interesting candidate for High Performance Computing. By digging into parallel algorithms solving three well known problems, our goal is to optimize, test and comp...

  12. The Japanese Society of Pathology Guidelines on the handling of pathological tissue samples for genomic research: Standard operating procedures based on empirical analyses.

    Science.gov (United States)

    Kanai, Yae; Nishihara, Hiroshi; Miyagi, Yohei; Tsuruyama, Tatsuhiro; Taguchi, Kenichi; Katoh, Hiroto; Takeuchi, Tomoyo; Gotoh, Masahiro; Kuramoto, Junko; Arai, Eri; Ojima, Hidenori; Shibuya, Ayako; Yoshida, Teruhiko; Akahane, Toshiaki; Kasajima, Rika; Morita, Kei-Ichi; Inazawa, Johji; Sasaki, Takeshi; Fukayama, Masashi; Oda, Yoshinao

    2018-02-01

    Genome research using appropriately collected pathological tissue samples is expected to yield breakthroughs in the development of biomarkers and identification of therapeutic targets for diseases such as cancers. In this connection, the Japanese Society of Pathology (JSP) has developed "The JSP Guidelines on the Handling of Pathological Tissue Samples for Genomic Research" based on an abundance of data from empirical analyses of tissue samples collected and stored under various conditions. Tissue samples should be collected from appropriate sites within surgically resected specimens, without disturbing the features on which pathological diagnosis is based, while avoiding bleeding or necrotic foci. They should be collected as soon as possible after resection: at the latest within about 3 h of storage at 4°C. Preferably, snap-frozen samples should be stored in liquid nitrogen (about -180°C) until use. When intending to use genomic DNA extracted from formalin-fixed paraffin-embedded tissue, 10% neutral buffered formalin should be used. Insufficient fixation and overfixation must both be avoided. We hope that pathologists, clinicians, clinical laboratory technicians and biobank operators will come to master the handling of pathological tissue samples based on the standard operating procedures in these Guidelines to yield results that will assist in the realization of genomic medicine. © 2018 The Authors. Pathology International published by Japanese Society of Pathology and John Wiley & Sons Australia, Ltd.

  13. Standard procedure of operation for the accomplishment of audit of quality in facilities of teletherapy with isotopic units of 60Co

    International Nuclear Information System (INIS)

    Larrinaga Cortina, Eduardo F.; Dominguez Hung, Lourdes; Campa Menendez, Raudel

    2001-01-01

    The use of the radiotherapy implies the necessity of rigorous quality standards in its different components, aiming to provide the best possible treatment and avoid potential patient's risks, that could even cause his/her death. Projects of technical cooperation have been developed in Cuba support by the International Atomic Energy Agency addresses to the implementation of Programs of Quality Assurance in radiotherapy services. The establishment of the National Quality Audit Program (PNAC) is a superior stage. The National Control Center for Medical Devices as the national regulator entity for the control and supervision of medical devices in the National Health System is the responsible for the making and execution of the PNAC. The audit modality selected was the inspection visit in situ due to its intrinsic advantages, our geographical extension and the number of radiotherapy services. This paper presents the methodology for the execution of the PNAC, in form of a Normalized Procedure of Operation that defines the objectives, scope, terms and definitions, responsibilities, composition and selection of the auditor team, security's conditions, materials and equipment, steps of the audit execution, results calculation and interpretation, records, etc. (author)

  14. [Current state of training in pharmacy education using a problem-based learning/tutorial model with simulated patients and standardized patients at National University Corporation].

    Science.gov (United States)

    Irie, Tetsumi; Nitta, Atsumi; Akaike, Akinori

    2012-01-01

    Simulated/standardized patient-based (SP) education and problem-based learning (PBL) tutorial education become a powerful tool to heighten the pharmacy students' will to learn in order to cultivate the responsibility to contribute to public health and welfare as a clinical professional and to facilitate students' competences to solve problems by themselves. What this program is trying to do is: 1) to establish the system to train, educate and supply SP who are effective in the training and education of pharmacy students in close cooperation with the medical schools and their affiliated hospitals; 2) to improve the quality of the current PBL tutorial education and thereby establish it as an advanced education program in the education of senior students. We carried out the questionnaire to National University Corporation which establishes a school of pharmacy, as to the training and education of SP. The analysis of the answers to the questionnaire revealed the present status of SP in the Pharmaceutical Objective Structured Clinical Examination (OSCE) in the Pharmaceutical Common Achievement Test, and the existence of the problems on how to standardize SP as well as how to cover such expenses. Furthermore, the activity of the first year consisted of the exchange and sharing of information regarding the existing method of training and education of SP and PBL tutorial education and the identification of the problems to be solved in order to improve the quality of the educational program.

  15. A meta-analysis of hypnosis for chronic pain problems: a comparison between hypnosis, standard care, and other psychological interventions.

    Science.gov (United States)

    Adachi, Tomonori; Fujino, Haruo; Nakae, Aya; Mashimo, Takashi; Sasaki, Jun

    2014-01-01

    Hypnosis is regarded as an effective treatment for psychological and physical ailments. However, its efficacy as a strategy for managing chronic pain has not been assessed through meta-analytical methods. The objective of the current study was to conduct a meta-analysis to assess the efficacy of hypnosis for managing chronic pain. When compared with standard care, hypnosis provided moderate treatment benefit. Hypnosis also showed a moderate superior effect as compared to other psychological interventions for a nonheadache group. The results suggest that hypnosis is efficacious for managing chronic pain. Given that large heterogeneity among the included studies was identified, the nature of hypnosis treatment is further discussed.

  16. Postoperative pain medication requirements in patients undergoing computer-assisted (“Robotic”) and standard laparoscopic procedures for newly diagnosed endometrial cancer.

    Science.gov (United States)

    Leitao, Mario M; Malhotra, Vivek; Briscoe, Gabriel; Suidan, Rudy; Dholakiya, Priyal; Santos, Kevin; Jewell, Elizabeth L; Brown, Carol L; Sonoda, Yukio; Abu-Rustum, Nadeem R; Barakat, Richard R; Gardner, Ginger J

    2013-10-01

    patients who had undergone an RBT hysterectomy compared to a standard total LSC hysterectomy for benign indications.13 A recent cost analysis suggested that patients experienced less pain and required less pain medication use after RBT procedures compared to LSC for endometrial cancer.14 Based on these reports, we sought to analyze postoperative pain and the use of pain medication in patients undergoing RBT compared to standard transperitoneal LSC procedures for newly diagnosed endometrial cancer during a concurrent time period. Of note, current RBT surgery is not truly robotic in that it is not autonomous. A more appropriate term is “computer-assisted surgery,” but to satisfy current convention, we refer to it as “robotic surgery” in this manuscript.

  17. Terms standardization between the rules of diagnosis radiation equipment safety management and atomic energy law: problems and suggestions

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Hwa Gon; Kang, Se Sik; Kim, Chang Soo; Park, Cheol Seo [Catholic University of Pusan, Busan (Korea, Republic of)

    2006-03-15

    The rules and terms are described different meaning in this results the research is accomplished for preventing practical workers from confusion. Atomic law are kept up modification and development in our situation by the ICRP's recommendation, on the other hand, the rules of diagnosis radiation equipment safety managements are modified partial, then resulted in confusion. The study was comparison between the rules of diagnosis radiation equipment safety management and atomic energy law, and the modification items obtained were as follows. With each other different the terms and units are used. With the exception of special terms for affairs usage, it is needless to say that common term uniformity is standardized. The standardization of rules and guidance have not need to confusion radiological practical workers. The following is omitted. The radiation protection against the patient and the hospital visitor. Radiation dose limit of the woman patient who is in the process of becoming pregnant. Radiation dose limit of the person who is not regarded as medical exposure. The control of the exposure of pregnant of women at work.

  18. Terms standardization between the rules of diagnosis radiation equipment safety management and atomic energy law: problems and suggestions

    International Nuclear Information System (INIS)

    Kim, Hwa Gon; Kang, Se Sik; Kim, Chang Soo; Park, Cheol Seo

    2006-01-01

    The rules and terms are described different meaning in this results the research is accomplished for preventing practical workers from confusion. Atomic law are kept up modification and development in our situation by the ICRP's recommendation, on the other hand, the rules of diagnosis radiation equipment safety managements are modified partial, then resulted in confusion. The study was comparison between the rules of diagnosis radiation equipment safety management and atomic energy law, and the modification items obtained were as follows. With each other different the terms and units are used. With the exception of special terms for affairs usage, it is needless to say that common term uniformity is standardized. The standardization of rules and guidance have not need to confusion radiological practical workers. The following is omitted. The radiation protection against the patient and the hospital visitor. Radiation dose limit of the woman patient who is in the process of becoming pregnant. Radiation dose limit of the person who is not regarded as medical exposure. The control of the exposure of pregnant of women at work

  19. Using a Standardized Patient to Improve Collaboration and Problem Solving Skills With CPAP Usage in the Home.

    Science.gov (United States)

    Williams, Margaret G; Ruhs, Joan

    2017-06-01

    A review of literature revealed a lack of research pertaining to nurses' or student nurses' knowledge of continuous positive airway pressure (CPAP) and the ability to troubleshoot CPAP malfunction. This study sought to answer the following questions: What are associate degree nursing (ADN) students' knowledge, interdisciplinary communication, and problem-solving skills regarding patients' home use of CPAP? Is there a change after participation in a simulation with a patient on CPAP in home setting? Twenty-one ADN students enrolled in small Midwest college participated. A preexperimental design of one group pretest posttest was used. Each student completed a demographic questionnaire, Mayo High Performance Teamwork Scale, Interprofessional collaborative simulation experience survey, and a CPAP knowledge base survey before and upon completion of the simulation. There were no changes in students' comfort, baseline knowledge, and basic understanding regarding CPAP. However, after the simulation, students described more detailed problem-solving skills, which included using respiratory therapists, durable medical equipment providers, and community resources. On the Mayo High Performance Teamwork Scale, all 16 items demonstrated improved scores (baseline mean = 21.65 and postsimulation mean = 25.6).

  20. Standard operating procedures for collection of soil and sediment samples for the Sediment-bound Contaminant Resiliency and Response (SCoRR) strategy pilot study

    Science.gov (United States)

    Fisher, Shawn C.; Reilly, Timothy J.; Jones, Daniel K.; Benzel, William M.; Griffin, Dale W.; Loftin, Keith A.; Iwanowicz, Luke R.; Cohl, Jonathan A.

    2015-12-17

    An understanding of the effects on human and ecological health brought by major coastal storms or flooding events is typically limited because of a lack of regionally consistent baseline and trends data in locations proximal to potential contaminant sources and mitigation activities, sensitive ecosystems, and recreational facilities where exposures are probable. In an attempt to close this gap, the U.S. Geological Survey (USGS) has implemented the Sediment-bound Contaminant Resiliency and Response (SCoRR) strategy pilot study to collect regional sediment-quality data prior to and in response to future coastal storms. The standard operating procedure (SOP) detailed in this document serves as the sample-collection protocol for the SCoRR strategy by providing step-by-step instructions for site preparation, sample collection and processing, and shipping of soil and surficial sediment (for example, bed sediment, marsh sediment, or beach material). The objectives of the SCoRR strategy pilot study are (1) to create a baseline of soil-, sand-, marsh sediment-, and bed-sediment-quality data from sites located in the coastal counties from Maine to Virginia based on their potential risk of being contaminated in the event of a major coastal storm or flooding (defined as Resiliency mode); and (2) respond to major coastal storms and flooding by reoccupying select baseline sites and sampling within days of the event (defined as Response mode). For both modes, samples are collected in a consistent manner to minimize bias and maximize quality control by ensuring that all sampling personnel across the region collect, document, and process soil and sediment samples following the procedures outlined in this SOP. Samples are analyzed using four USGS-developed screening methods—inorganic geochemistry, organic geochemistry, pathogens, and biological assays—which are also outlined in this SOP. Because the SCoRR strategy employs a multi-metric approach for sample analyses, this

  1. Analogy, an Alternative Model.
 Critics to the standard model of analogical problems solving and proposals for an alternative one

    Directory of Open Access Journals (Sweden)

    Ricardo A. Minervino

    2016-02-01

    Full Text Available The authors made an extension of Hofstadter‘s criticisms against the standard approach in analogical thinking represented by the structure-mapping theory of Gentner and the multiconstraint theory of Holyoak and Thagard. Based on this extension, they proposed a non-serial model of analogical problem solving. Against the standard approach, the model postulates that: (a people detect and evaluate differences between mapped elements before the subprocess of inference generation and consider them in order to control it, and (b properties of an element that explain why the element could fill a certain role in the base problem resolution (PERs play a crucial role in these detection and evaluation operations, and also in post-inferences subprocesses. An experiment showed that: (a people detect and evaluate the relevance of differences between mapped elements before inference generation, (b that they inhibit the generation of literal inferences when they face relevant differences, and (c that they stop the subprocess when they recognize insuperable ones. The results also showed that base PERs are reactivated at different moments of analogical transfer. The data obtained are incompatible with the standard theories of analogical thinking, which treat inference generation as a syntactic mechanism and exclude contextual semantic analysis from the study of analogy. 

  2. Standardization of clinical enzyme analysis using frozen human serum pools with values assigned by the International Federation of Clinical Chemistry and Laboratory Medicine reference measurement procedures.

    Science.gov (United States)

    Tong, Qing; Chen, Baorong; Zhang, Rui; Zuo, Chang

    Variation in clinical enzyme analysis, particularly across different measuring systems and laboratories, represents a critical but long-lasting problem in diagnosis. Calibrators with traceability and commutability are imminently needed to harmonize analysis in laboratory medicine. Fresh frozen human serum pools were assigned values for alanine aminotransferase (ALT), aspartate aminotransferase (AST), gamma-glutamyltransferase (GGT), creatine kinase (CK) and lactate dehydrogenase (LDH) by six laboratories with established International Federation of Clinical Chemistry and Laboratory Medicine reference measurement procedures. These serum pools were then used across 76 laboratories as a calibrator in the analysis of five enzymes. Bias and imprecision in the measurement of the five enzymes tested were significantly reduced by using the value-assigned serum in analytical systems with open and single-point calibration. The median (interquartile range) of the relative biases of ALT, AST, GGT, CK and LDH were 2.0% (0.6-3.4%), 0.8% (-0.8-2.3%), 1.0% (-0.5-2.0%), 0.2% (-0.3-1.0%) and 0.2% (-0.9-1.1%), respectively. Before calibration, the interlaboratory coefficients of variation (CVs) in the analysis of patient serum samples were 8.0-8.2%, 7.3-8.5%, 8.1-8.7%, 5.1-5.9% and 5.8-6.4% for ALT, AST, GGT, CK and LDH, respectively; after calibration, the CVs decreased to 2.7-3.3%, 3.0-3.6%, 1.6-2.1%, 1.8-1.9% and 3.3-3.5%, respectively. The results suggest that the use of fresh frozen serum pools significantly improved the comparability of test results in analytical systems with open and single-point calibration.

  3. Emergency procedures

    International Nuclear Information System (INIS)

    Abd Nasir Ibrahim; Azali Muhammad; Ab Razak Hamzah; Abd Aziz Mohamed; Mohammad Pauzi Ismail

    2004-01-01

    The following subjects are discussed - Emergency Procedures: emergency equipment, emergency procedures; emergency procedure involving X-Ray equipment; emergency procedure involving radioactive sources

  4. Perform qualify reliability-power tests by shooting common mistakes: practical problems and standard answers per Telcordia/Bellcore requests

    Science.gov (United States)

    Yu, Zheng

    2002-08-01

    Facing the new demands of the optical fiber communications market, almost all the performance and reliability of optical network system are dependent on the qualification of the fiber optics components. So, how to comply with the system requirements, the Telcordia / Bellcore reliability and high-power testing has become the key issue for the fiber optics components manufacturers. The qualification of Telcordia / Bellcore reliability or high-power testing is a crucial issue for the manufacturers. It is relating to who is the outstanding one in the intense competition market. These testing also need maintenances and optimizations. Now, work on the reliability and high-power testing have become the new demands in the market. The way is needed to get the 'Triple-Win' goal expected by the component-makers, the reliability-testers and the system-users. To those who are meeting practical problems for the testing, there are following seven topics that deal with how to shoot the common mistakes to perform qualify reliability and high-power testing: ¸ Qualification maintenance requirements for the reliability testing ¸ Lots control for preparing the reliability testing ¸ Sampling select per the reliability testing ¸ Interim measurements during the reliability testing ¸ Basic referencing factors relating to the high-power testing ¸ Necessity of re-qualification testing for the changing of producing ¸ Understanding the similarity for product family by the definitions

  5. Toward a standardized investigation protocol in sudden unexpected deaths in infancy in South Africa: a multicenter study of medico-legal investigation procedures and outcomes.

    Science.gov (United States)

    du Toit-Prinsloo, Lorraine; Dempers, Johan; Verster, Janette; Hattingh, Christa; Nel, Hestelle; Brandt, V D; Jordaan, Joyce; Saayman, Gert

    2013-09-01

    South Africa manifests a socio-economic dichotomy that shows features of both a developed and developing country. As a result of this, areas exist where a lack of resources and expertise prevents the implementation of a highly standardized protocol for the investigation of sudden and unexpected deaths in infants (SUDI). Although the medico-legal mortuaries attached to academic centers have the capacity to implement standardized protocols, a previous study conducted at two large medico-legal mortuaries indicated otherwise. This study also revealed that the exact number and incidence of sudden infant death syndrome (SIDS) cases was unknown. These findings prompted a multicenter study of the medico-legal investigation procedures and outcomes in five academic centers in South Africa. A retrospective case audit was conducted for a 5-year period (2005-2009) at medico-legal laboratories attached to universities in Bloemfontein, Cape Town-Tygerberg, Durban, Johannesburg, and Pretoria. The total case load as well as the total number of infants younger than 1 year of age admitted to these mortuaries was documented. The case files on all infants younger than 1 year of age who were admitted as sudden and unexpected or unexplained deaths were included in the study population. Data collected on the target population included demographic details, the nature and scope of the post-mortem examinations, as well as the final outcome (cause of death). A total case load of 80,399 cases were admitted to the mortuaries over the 5 year period with a total of 3,295 (6.5 %) infants. In the infant group, 591 (0.7 %) died from non-natural causes and 2,704 (3.3 %) cases of sudden, unexpected and/or unexplained deaths in infants were admitted and included in the detailed case analysis study. One hundred and ninety-nine babies were between 0 and 7 days of age and 210 babies between 8 and 30 days. The remaining 2,295 infants were between 1 month and 12 months of age. Death scene investigation was

  6. Application of self-adaptive procedure to the thermal problems analysis under steady-state and transient regimens; Aplicacao de procedimento auto-adaptativo na analise de problemas termicos no regime permanente e transiente

    Energy Technology Data Exchange (ETDEWEB)

    Lyra, Paulo Roberto Maciel [Pernambuco Univ., Recife, PE (Brazil). Dept. de Engenharia Civil

    1991-12-31

    This work describes a procedure for the adaptive time dependent Finite Element Method using an automatic mesh refinement (H-Version) that efficiently reduces estimated errors ( a posteriori) below pre-assigned limits. Classical model problem for steady-state heat transfer are investigated, and the results are compared with the analytical solution. Then some typical time-dependent problem are qualitatively analysed. (author) 10 refs., 7 figs.

  7. Chapter 2. Surge capacity and infrastructure considerations for mass critical care. Recommendations and standard operating procedures for intensive care unit and hospital preparations for an influenza epidemic or mass disaster

    NARCIS (Netherlands)

    Hick, John L.; Christian, Michael D.; Sprung, Charles L.; Camargo, Ruben; Ceraso, Daniel; Azoulay, Elie; Duguet, Alexandre; Guery, Benoit; Reinhart, Konrad; Adini, Bruria; Barlavie, Yaron; Benin-Goren, Odeda; Cohen, Robert; Klein, Motti; Leoniv, Yuval; Margalit, Gila; Rubinovitch, Bina; Sonnenblick, Moshe; Steinberg, Avraham; Weissman, Charles; Wolff, Donna; Kesecioglu, Jozef; de Jong, Menno; Moreno, Rui; An, Youzhong; Du, Bin; Joynt, Gavin M.; Colvin, John; Loo, Shi; Richards, Guy; Artigas, Antonio; Pugin, Jerome; Amundson, Dennis; Devereaux, Asha; Beigel, John; Danis, Marion; Farmer, Chris; Maki, Dennis; Masur, Henry; Rubinson, Lewis; Sandrock, Christian; Talmor, Daniel; Truog, Robert; Zimmerman, Janice; Brett, Steve; Montgomery, Hugh; Rhodes, Andrew; Sanderson, Frances; Taylor, Bruce; Monrgomery, Hugh

    2010-01-01

    To provide recommendations and standard operating procedures for intensive care unit (ICU) and hospital preparations for a mass disaster or influenza epidemic with a specific focus on surge capacity and infrastructure considerations. Based on a literature review and expert opinion, a Delphi process

  8. Chapter 6. Protection of patients and staff during a pandemic. Recommendations and standard operating procedures for intensive care unit and hospital preparations for an influenza epidemic or mass disaster

    NARCIS (Netherlands)

    Taylor, Bruce L.; Montgomery, Hugh E.; Rhodes, Andrew; Sprung, Charles L.; Christian, Michael D.; Camargo, Ruben; Ceraso, Daniel; Azoulay, Elie; Duguet, Alexandre; Guery, Benoit; Reinhart, Konrad; Adini, Bruria; Barlavie, Yaron; Benin-Goren, Odeda; Cohen, Robert; Klein, Motti; Leoniv, Yuval; Margalit, Gila; Rubinovitch, Bina; Sonnenblick, Moshe; Steinberg, Avraham; Weissman, Charles; Wolff, Donna; Kesecioglu, Jozef; de Jong, Menno; Moreno, Rui; An, Youzhong; Du, Bin; Joynt, Gavin M.; Colvin, John; Loo, Shi; Richards, Guy; Artigas, Antonio; Pugin, Jerome; Amundson, Dennis; Devereaux, Asha; Beigel, John; Danis, Marion; Farmer, Chris; Hick, John L.; Maki, Dennis; Masur, Henry; Rubinson, Lewis; Sandrock, Christian; Talmor, Daniel; Truog, Robert; Zimmerman, Janice; Brett, Steve; Montgomery, Hugh; Sanderson, Frances

    2010-01-01

    To provide recommendations and standard operating procedures (SOPs) for intensive care unit (ICU) and hospital preparations for an influenza pandemic or mass disaster with a specific focus on protection of patients and staff. Based on a literature review and expert opinion, a Delphi process was used

  9. NHEXAS PHASE I ARIZONA STUDY--STANDARD OPERATING PROCEDURE FOR COLLECTION, STORAGE AND SHIPMENT OF URINE SAMPLES FOR SELECTED METALS AND PESTICIDES (UA-F-20.1)

    Science.gov (United States)

    The purpose of this SOP is to guide the collection, storage, and shipment of urine samples collected for the NHEXAS Arizona project. This SOP provides a brief description of sample, collection, preservation, storage, shipping, and custody procedures. This procedure was followed ...

  10. radioactive waste disposal standards abroad

    International Nuclear Information System (INIS)

    Lu Yan; Xin Pingping; Wu Jian; Zhang Xue

    2012-01-01

    With the world focus on human health and environmental protection, the problem of radioactive waste disposal has gradually become a global issue, and the focus of attention of public. The safety of radioactive waste disposal, is not only related to human health and environmental safety, but also an important factor of affecting the sustainable development of nuclear energy. In recent years the formulation of the radioactive waste disposal standards has been generally paid attention to at home and abroad, and it has made great progress. In China, radioactive waste management standards are being improved, and there are many new standards need to be developed. The revised task of implement standards is very arduous, and there are many areas for improvement about methods and procedures of the preparation of standards. This paper studies the current situation of radioactive waste disposal standards of the International Atomic Energy Agency, USA, France, Britain, Russia, Japan, and give some corresponding recommendations of our radioactive waste disposal standards. (authors)

  11. Do English NHS Microbiology laboratories offer adequate services for the diagnosis of UTI in children? Healthcare Quality Improvement Partnership (HQIP) Audit of Standard Operational Procedures.

    Science.gov (United States)

    McNulty, Cliodna A M; Verlander, Neville Q; Moore, Philippa C L; Larcombe, James; Dudley, Jan; Banerjee, Jaydip; Jadresic, Lyda

    2015-09-01

    The National Institute of Care Excellence (NICE) 2007 guidance CG54, on urinary tract infection (UTI) in children, states that clinicians should use urgent microscopy and culture as the preferred method for diagnosing UTI in the hospital setting for severe illness in children under 3 years old and from the GP setting in children under 3 years old with intermediate risk of severe illness. NICE also recommends that all 'infants and children with atypical UTI (including non-Escherichia coli infections) should have renal imaging after a first infection'. We surveyed all microbiology laboratories in England with Clinical Pathology Accreditation to determine standard operating procedures (SOPs) for urgent microscopy, culture and reporting of children's urine and to ascertain whether the SOPs facilitate compliance with NICE guidance. We undertook a computer search in six microbiology laboratories in south-west England to determine urine submissions and urine reports in children under 3 years. Seventy-three per cent of laboratories (110/150) participated. Enterobacteriaceae that were not E. coli were reported only as coliforms (rather than non-E. coli coliforms) by 61% (67/110) of laboratories. Eighty-eight per cent of laboratories (97/110) provided urgent microscopy for hospital and 54% for general practice (GP) paediatric urines; 61% of laboratories (confidence interval 52-70%) cultured 1 μl volume of urine, which equates to one colony if the bacterial load is 106 c.f.u. l(-1). Only 22% (24/110) of laboratories reported non-E. coli coliforms and provided urgent microscopy for both hospital and GP childhood urines; only three laboratories also cultured a 5 μl volume of urine. Only one of six laboratories in our submission audit had a significant increase in urine submissions and urines reported from children less than 3 years old between the predicted pre-2007 level in the absence of guidance and the 2008 level following publication of the NICE guidance. Less than a

  12. An actor-oriented transfer perspective on high school students’ development of the use of procedures to solve problems on “rate of change”.

    NARCIS (Netherlands)

    Roorda, Gerrit; Goedhart, Martin; Vos, Pauline

    2015-01-01

    This article reports on a longitudinal observation study about students’ development in their use of procedures to calculate instantaneous rate of change. Different procedures for solving tasks on rate of change are taught in mathematics and physics classes, and together they form a repertoire. Our

  13. [The coroner's autopsies in the Great Britain: the problems related to the quality of the studies, standardization, auditing, financial support and the approaches to their solution].

    Science.gov (United States)

    Makarov, I Yu; Fetisov, V A; Filimonov, B A; Gusarov, A A

    The objective of the present study was to analyze the experience of the coroners and pathologists in the Great Britain based on the results of the coroner's autopsies and recommendations of the experts involved in the activities carried out in the framework of the National Confidential Enquiry into Patient Outcome and Death program (NCEPOD). The recommendations are designed to reform the country's medical examiner system, improve the equipment of the mortuary facilities, and optimize funding for the autopsy studies. The authors consider in the chronological order the following issues of the coroners and pathologists' activities: organization of their work and its procedural aspects, ordering coroner's autopsies, preparation for their performance, analysis of the relevant documentation (autopsy reports) and medical case histories (discharge summaries). Also discussed are the recommendations of the NCEPOD experts for the improvement of the said studies with the detailed analysis of the causes underlying the aforementioned problems and concise comments of the authors.

  14. Radiochemical procedures

    International Nuclear Information System (INIS)

    Lyon, W.S.

    1982-01-01

    The modern counting instrumentation has largely obviated the need for separation processes in the radiochemical analysis but problems in low-level radioactivity measurement, environmental-type analyses, and special situations caused in the last years a renaissance of the need for separation techniques. Most of the radiochemical procedures, based on the classic works of the Manhattan Project chemists of the 1940's, were published in the National Nuclear Energy Series (NNES). Improvements such as new solvent extraction and ion exchange separations have been added to these methods throughout the years. Recently the Los Alamos Group have reissued their collected Radiochemical Procedures containing a short summary and review of basic inorganic chemistry - 'Chemistry of the Elements on the Basis of Electronic Configuration'. (A.L.)

  15. Standards for holdup measurement

    International Nuclear Information System (INIS)

    Zucker, M.S.

    1982-01-01

    Holdup measurement, needed for material balance, depend intensively on standards and on interpretation of the calibration procedure. More than other measurements, the calibration procedure using the standard becomes part of the standard. Standards practical for field use and calibration techniques have been developed. While accuracy in holdup measurements is comparatively poor, avoidance of bias is a necessary goal

  16. Control of systems with I/O delay via reduction to a one-block problem

    NARCIS (Netherlands)

    Meinsma, Gjerrit; Mirkin, Leonid; Zhong, Qing-Chang

    2002-01-01

    In this paper, the standard (four-block) H/sup /spl infin// control problem for systems with a single delay in the feedback loop is studied. A simple procedure of the reduction of the problem to an equivalent one-block problem having particularly simple structure is proposed. The one-block problem

  17. Semiparametric Bernstein–von Mises for the error standard deviation

    NARCIS (Netherlands)

    Jonge, de R.; Zanten, van J.H.

    2013-01-01

    We study Bayes procedures for nonparametric regression problems with Gaussian errors, giving conditions under which a Bernstein–von Mises result holds for the marginal posterior distribution of the error standard deviation. We apply our general results to show that a single Bayes procedure using a

  18. Semiparametric Bernstein-von Mises for the error standard deviation

    NARCIS (Netherlands)

    de Jonge, R.; van Zanten, H.

    2013-01-01

    We study Bayes procedures for nonparametric regression problems with Gaussian errors, giving conditions under which a Bernstein-von Mises result holds for the marginal posterior distribution of the error standard deviation. We apply our general results to show that a single Bayes procedure using a

  19. NHEXAS PHASE I MARYLAND STUDY--STANDARD OPERATING PROCEDURE FOR COLLECTION, STORAGE, AND SHIPMENT OF URINE SAMPLES FOR METAL, PESTICIDE, AND CREATININE ANALYSIS (F10)

    Science.gov (United States)

    The purpose of this SOP is to describe the procedures for collection, storage, and shipment of urine samples for metal, pesticides, and creatinine analysis. Samples were collected on Days 2 and 8 of each Cycle. The Day 2 sample was analyzed for metals and creatinine. The Day 8...

  20. Simulation of the IAEA's fourth Standard Problem Exercise small-break loss-of-coolant accident using RELAP5/MOD.3.1

    International Nuclear Information System (INIS)

    Cebull, P.P.; Hassan, Y.A.

    1995-01-01

    A small-break loss-of-coolant accident experiment conducted at the PMK-2 integral test facility in Hungary is analyzed using the RELAP5/MOD3.1 thermal-hydraulic code. The experiment simulated a 7.4% break in the cold leg of a VVER-440/213-type nuclear power plant as part of the International Atomic Energy Agency's Fourth Standard Problem Exercise (SPE-4). Blind calculations of the exercise are presented, and the timing of various events throughout the transient is discussed. A posttest analysis is performed in which the sensitivity of the calculated results is investigated. The code RELAP5 predicts most of the transient events well, although a few problems are noted, particularly the failure of RELAP5 to predict dryout in the core even through the collapsed liquid level fell below the top of the heated portion. A discrepancy between the predicted primary mass inventory distribution and the experimental data is identified. Finally, the primary and secondary pressures calculated by RELAP5 fell too rapidly during the latter part of the transient, resulting in rather large errors in the predicted timing of some pressure-actuated events