European standards and regulation - CEN/CENELEC

Energy Technology Data Exchange (ETDEWEB)

Caballero, J. [AENOR, Madrid (Spain)

1997-02-27

An overview is given of the European Standards structure, as well as the general Directives and Regulations related to the Heating, Ventilation and Air Conditioning Sector. The importance of standardisation, both on quality and as a strategic tool for manufacturers, is stressed. Participation in the elaboration of standards makes it possible to reflect a manufacturer`s technology in the standards. Voluntary standardisation can be used as a differentiating element. European standards for the HVAC sector are being elaborated by the European Standardisation Committee (CEN), the European Electrotechnical Standardisation Committee (CENELEC) and by the European Telecommunication Institute (ETSI)

7 CFR 58.514 - Container fillers.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Container fillers. 58.514 Section 58.514 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards....514 Container fillers. Shall comply with the 3-A Sanitary Standards for Equipment for Packaging Frozen...

Safety analysis report for packaging: the unirradiated fuel shipping container

International Nuclear Information System (INIS)

Evans, J.H.; Shipley, W.D.; Mouring, R.W.

1979-09-01

The container was evaluated analytically to determine its compliance with the applicable regulations governing containers in which radioactive and fissile materials are transported, and the evaluation is the subject of this report. Computational and test procedures were used to determine the structural integrity and thermal behavior of the container relative to the general standards for normal conditions of transport and the standards for hypothetical accident conditions. Results of the evaluation demonstrate that the container is in compliance with the applicable regulations

77 FR 27550 - Federal Acquisition Regulation; Revision of Cost Accounting Standards Threshold

Science.gov (United States)

2012-05-10

...] RIN 9000-AM25 Federal Acquisition Regulation; Revision of Cost Accounting Standards Threshold AGENCY... Federal Acquisition Regulation (FAR) to revise the threshold for applicability of cost accounting standards in order to implement a recent rule of the Cost Accounting Standards Board and statutory...

Standardized analyses of nuclear shipping containers

International Nuclear Information System (INIS)

Parks, C.V.; Hermann, O.W.; Petrie, L.M.; Hoffman, T.J.; Tang, J.S.; Landers, N.F.; Turner, W.D.

1983-01-01

This paper describes improved capabilities for analyses of nuclear fuel shipping containers within SCALE -- a modular code system for Standardized Computer Analyses for Licensing Evaluation. Criticality analysis improvements include the new KENO V, a code which contains an enhanced geometry package and a new control module which uses KENO V and allows a criticality search on optimum pitch (maximum k-effective) to be performed. The SAS2 sequence is a new shielding analysis module which couples fuel burnup, source term generation, and radial cask shielding. The SAS5 shielding sequence allows a multidimensional Monte Carlo analysis of a shipping cask with code generated biasing of the particle histories. The thermal analysis sequence (HTAS1) provides an easy-to-use tool for evaluating a shipping cask response to the accident capability of the SCALE system to provide the cask designer or evaluator with a computational system that provides the automated procedures and easy-to-understand input that leads to standarization

45 CFR 91.18 - Age distinctions contained in HHS regulations.

Science.gov (United States)

2010-10-01

....18 Section 91.18 Public Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL ADMINISTRATION... distinctions contained in a rule or regulation issued by HHS shall be presumed to be necessary to the achievement of a statutory objective of the program or activity to which the rule or regulation applies...

7 CFR 51.1005 - Standard pack.

Science.gov (United States)

2010-01-01

... Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE REGULATIONS AND STANDARDS UNDER THE AGRICULTURAL MARKETING ACT OF 1946... not more than 10 percent, by count of the fruit in any container may vary more than four-sixteenths of...

Radioactive materials packaging standards and regulations: Making sense of it all

International Nuclear Information System (INIS)

Pope, R.B.; Rawl, R.R.

1989-01-01

Numerous regulations and standards, both national and international, apply to the packaging and transportation of radioactive material. These are legal and technical prerequisites to practically every action that a designer or user of a radioactive material transportation package will perform. The identity and applicability of these requirements and the bodies that formulate them are also not readily understood. This paper addresses the roles that various international bodies play in developing and implementing the various regulations and standards. It uses the US regulatory and standards-making bodies to illustrate how international requirements feed the domestic control of packaging and transport. It explains the scope and interactions between domestic and international regulatory and standards agencies and summarizes the status and major standards activities at the international level. The overview provided by this paper will be valuable to designers and users of radioactive material packages for better understanding and use of both standards and regulations, and for complying with regulatory requirements in the radioactive materials transportation field. 11 refs., 2 figs

Review of codes, standards, and regulations for natural gas locomotives.

Science.gov (United States)

2014-06-01

This report identified, collected, and summarized relevant international codes, standards, and regulations with potential : applicability to the use of natural gas as a locomotive fuel. Few international or country-specific codes, standards, and regu...

International Safety Regulation and Standards for Space Travel and Commerce

Science.gov (United States)

Pelton, J. N.; Jakhu, R.

The evolution of air travel has led to the adoption of the 1944 Chicago Convention that created the International Civil Aviation Organization (ICAO), headquartered in Montreal, Canada, and the propagation of aviation safety standards. Today, ICAO standardizes and harmonizes commercial air safety worldwide. Space travel and space safety are still at an early stage of development, and the adoption of international space safety standards and regulation still remains largely at the national level. This paper explores the international treaties and conventions that govern space travel, applications and exploration today and analyzes current efforts to create space safety standards and regulations at the national, regional and global level. Recent efforts to create a commercial space travel industry and to license commercial space ports are foreseen as means to hasten a space safety regulatory process.

Statistical benchmarking in utility regulation: Role, standards and methods

International Nuclear Information System (INIS)

Newton Lowry, Mark; Getachew, Lullit

2009-01-01

Statistical benchmarking is being used with increasing frequency around the world in utility rate regulation. We discuss how and where benchmarking is in use for this purpose and the pros and cons of regulatory benchmarking. We then discuss alternative performance standards and benchmarking methods in regulatory applications. We use these to propose guidelines for the appropriate use of benchmarking in the rate setting process. The standards, which we term the competitive market and frontier paradigms, have a bearing on method selection. These along with regulatory experience suggest that benchmarking can either be used for prudence review in regulation or to establish rates or rate setting mechanisms directly

Safety analysis report for packaging Lawrence Livermore Laboratories shipping containers

International Nuclear Information System (INIS)

Evans, J.H.

1975-12-01

The Lawrence Livermore Laboratories shipping containers were designed at Oak Ridge National Laboratory for use in transporting weapons and nuclear components. The design for the containers was evaluated to show compliance with applicable regulations governing packages in which radioactive and fissile materials are transported. Computational procedures were used to determine the structural integrity and thermal behavior of the containers relative to the standards for the normal conditions of transport. A full-scale container test model was destructively tested to verify compliance with the standards for the accident conditions. The results of the analytical evaluations and the tests demonstrate that the design for the Lawrence Livermore Laboratories shipping containers is in compliance with the applicable regulations

36 CFR 400.1 - Cross-references to employees' ethical conduct standards, financial disclosure regulations and...

Science.gov (United States)

2010-07-01

...' ethical conduct standards, financial disclosure regulations and other conduct rules. 400.1 Section 400.1... CONDUCT § 400.1 Cross-references to employees' ethical conduct standards, financial disclosure regulations... executive branch-wide standards of ethical conduct and financial disclosure regulations at 5 CFR parts 2634...

24 CFR 0.1 - Cross-reference to employees ethical conduct standards and financial disclosure regulations.

Science.gov (United States)

2010-04-01

... ethical conduct standards and financial disclosure regulations. 0.1 Section 0.1 Housing and Urban... Cross-reference to employees ethical conduct standards and financial disclosure regulations. Employees...-wide standards of ethical conduct at 5 CFR part 2635, the Department's regulation at 5 CFR part 7501...

76 FR 8989 - Federal Acquisition Regulation; Updated Financial Accounting Standards Board Accounting References

Science.gov (United States)

2011-02-16

... Acquisition Regulation; Updated Financial Accounting Standards Board Accounting References AGENCIES... Acquisition Regulation (FAR) to update references to authoritative accounting standards owing to the Financial... Accounting Principles (GAAP) (``Codification of GAAP''). DATES: Interested parties should submit written...

Merits and difficulties in adopting codes, standards and nuclear regulations

International Nuclear Information System (INIS)

El-Saiedi, A.F.; Morsy, S.; Mariy, A.

1978-01-01

Developing countries planning for introducing nuclear power plants as a source of energy have to develop or adopt sound regulatory practices. These are necessary to help governmental authorities to assess the safety of nuclear power plants and to perform inspections needed to confirm the established safe and sound limits. The first requirement is to form an independent regulatory body capable of setting up and enforcing proper safety regulations. The formation of this body is governed by several considerations related to local conditions in the developing countries, which may not always be favourable. It is quite impractical for countries with limited experience in the nuclear power field to develop their own codes, standards and regulations required for the nuclear regulatory body to perform its tasks. A practical way is to adopt codes, standards and regulations of a well-developed country. This has merits as well as drawbacks. The latter are related to problems of personnel, software, equipment and facilities. The difficulties involved in forming a nuclear regulatory body, and the merits and difficulties in adopting foreign codes, standards and regulations required for such body to perform its tasks, are discussed in this paper. Discussions are applicable to many developing countries and particular emphasis is given to the conditions and practices in Egypt. (author)

78 FR 55171 - Removal of Standards of Ethical Conduct Regulations

Science.gov (United States)

2013-09-10

... Ethical Conduct Regulations AGENCY: Special Inspector General for Iraq Reconstruction. ACTION: Final rule... concurrence of the Office of Government Ethics (OGE), issued a final rule for employees of the SIGIR that supplemented the executive-branch-wide Standards of Ethical Conduct (Standards) issued by OGE. With certain...

3 CFR 100.1 - Ethical conduct standards and financial disclosure regulations.

Science.gov (United States)

2010-01-01

... 3 The President 1 2010-01-01 2010-01-01 false Ethical conduct standards and financial disclosure... § 100.1 Ethical conduct standards and financial disclosure regulations. Employees of the Executive Office of the President are subject to the executive branch-wide standards of ethical conduct at 5 CFR...

The evolution of the structure and application of U.S. NRC regulations and standards

International Nuclear Information System (INIS)

Murley, T.E.; Rosztoczy, Z.R.; McPherson, G.D.

1991-01-01

NRC regulations and standards and their implementation have evolved from early adaptations of conventional engineering practices to a mature, cohesive set of regulations that govern NRC regulation of nuclear power plant safety in the United States. From a simple set of rules and design criteria and from the standards of the professional engineering societies, a hierarchy of practices, standards, guides, rules and goals has developed. Resting on a foundation of industrial practices, this hierarchy rises through levels of national standards, regulatory guides and standard review plans, policy statements and NRC regulations. The licensing process is evolving today toward one that permits both site approval and standard design certification before the plant is constructed. At the present time, NRC is reviewing five standard designs for certification for a period of 15 years. NRC focuses its regulation of operating nuclear plants on inspections conducted from five regional offices. Resident inspectors, specialist inspectors, and multi-disciplinary inspection teams examine specific plant situations. The results of all these inspections are used to develop a complete understanding of a plant's physical condition, its operation, maintenance and management. To improve safe operation of nuclear plants in the U.S., a most important program, the Systematic Assessment of Licensee Performance, measures operational performance, using a broad spectrum of functional areas. (orig.)

7 CFR 915.305 - Florida Avocado Container Regulation 5.

Science.gov (United States)

2010-01-01

... Regulation 5. (a) No handler shall handle any avocados for the fresh market from the production area to any... handler shall handle any avocados for the fresh market in 20 bushel plastic field bins to destinations inside the production area. (d) Avocados handled for the fresh market in containers other than those...

1 CFR 21.14 - Deviations from standard organization of the Code of Federal Regulations.

Science.gov (United States)

2010-01-01

... 1 General Provisions 1 2010-01-01 2010-01-01 false Deviations from standard organization of the... CODIFICATION General Numbering § 21.14 Deviations from standard organization of the Code of Federal Regulations. (a) Any deviation from standard Code of Federal Regulations designations must be approved in advance...

7 CFR 33.12 - Apples not subject to regulation.

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Apples not subject to regulation. 33.12 Section 33.12 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE COMMODITY STANDARDS AND STANDARD CONTAINER...

41 CFR 105-735.1 - Cross-references to employee ethical conduct standards, financial disclosure regulations, and...

Science.gov (United States)

2010-07-01

... employee ethical conduct standards, financial disclosure regulations, and other regulations. 105-735.1... CONDUCT § 105-735.1 Cross-references to employee ethical conduct standards, financial disclosure... executive branch-wide standards of ethical conduct at 5 CFR part 2635, GSA's regulations at 5 CFR part 6701...

Procedure manual: protocol for regulation of petroleum hydrocarbons in water under the special waste and contaminated sites regulation

International Nuclear Information System (INIS)

Evans, P.; Partridge, E.

2002-05-01

This document details the regulation governing numerical standards for petroleum hydrocarbons in water under the special waste and contaminated sites regulations of British Columbia. Groundwater containing benzene, toluene, ethylbenzene or xylenes in excess of the leachate standards is exempted from the regulatory regime of the Special Waste Regulation. The document contains a description of the conditions that apply to the management of petroleum hydrocarbons in water at contaminated sites. Some definitions are included, followed by an overview of the regulation. The third section deals with authorization and mandatory conditions, while additional requirements that might apply are enumerated in section four. This protocol directly affects the Environmental Management, and the Environmental Protection Regional Operations organizations. 1 tab

Standard practice for sampling special nuclear materials in multi-container lots

CERN Document Server

American Society for Testing and Materials. Philadelphia

1987-01-01

1.1 This practice provides an aid in designing a sampling and analysis plan for the purpose of minimizing random error in the measurement of the amount of nuclear material in a lot consisting of several containers. The problem addressed is the selection of the number of containers to be sampled, the number of samples to be taken from each sampled container, and the number of aliquot analyses to be performed on each sample. 1.2 This practice provides examples for application as well as the necessary development for understanding the statistics involved. The uniqueness of most situations does not allow presentation of step-by-step procedures for designing sampling plans. It is recommended that a statistician experienced in materials sampling be consulted when developing such plans. 1.3 The values stated in SI units are to be regarded as the standard. 1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standar...

76 FR 37703 - Regulation of Fuels and Fuel Additives: 2012 Renewable Fuel Standards; Public Hearing

Science.gov (United States)

2011-06-28

... Regulation of Fuels and Fuel Additives: 2012 Renewable Fuel Standards; Public Hearing AGENCY: Environmental... hearing to be held for the proposed rule ``Regulation of Fuels and Fuel Additives: 2012 Renewable Fuel... be proposing amendments to the renewable fuel standard program regulations to establish annual...

77 FR 202 - Federal Acquisition Regulation; Updated Financial Accounting Standards Board Accounting References

Science.gov (United States)

2012-01-03

... 9000-AM00 Federal Acquisition Regulation; Updated Financial Accounting Standards Board Accounting... accounting standards owing to the Financial Accounting Standards Board's Accounting Standards Codification of Generally Accepted Accounting Principles. DATES: Effective Date: February 2, 2012. FOR FURTHER INFORMATION...

10 CFR 625.3 - Standard sales provisions.

Science.gov (United States)

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Standard sales provisions. 625.3 Section 625.3 Energy DEPARTMENT OF ENERGY (CONTINUED) SALES REGULATION PRICE COMPETITIVE SALE OF STRATEGIC PETROLEUM RESERVE PETROLEUM § 625.3 Standard sales provisions. (a) Contents. The Standards Sales Provisions shall contain...

7 CFR 29.1225 - Key to standard grademarks.

Science.gov (United States)

2010-01-01

... Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE COMMODITY STANDARDS AND STANDARD CONTAINER.... Groups B—Leaf. H—Smoking Leaf. C—Cutters. X—Lugs. P—Primings. M—Mixed Group. N—Nondescript. S—Scrap...

Self-Monitoring of Self-Regulation during Math Homework Behaviour Using Standardized Diaries

Science.gov (United States)

Schmitz, Bernhard; Perels, Franziska

2011-01-01

This study aims at enhancing math learning and general self-regulation by supporting daily self-regulated learning during math homework. The authors use standardized diaries as a self-monitoring tool to support self-regulatory behaviour. Following the theory of self-monitoring, frequent self-monitoring of self-regulation will lead to an…

18 CFR 1300.101 - Cross references to employee ethical conduct standards and other applicable regulations.

Science.gov (United States)

2010-04-01

... employee ethical conduct standards and other applicable regulations. 1300.101 Section 1300.101 Conservation... TENNESSEE VALLEY AUTHORITY § 1300.101 Cross references to employee ethical conduct standards and other...-wide standards of ethical conduct at 5 CFR part 2635 and to the TVA regulations at 5 CFR part 7901...

Safety analysis report for packaging: the ORNL HFIR unirradiated fuel element shipping container

International Nuclear Information System (INIS)

Evans, J.H.; Boulet, J.A.M.; Eversole, R.E.

1977-11-01

The ORNL HFIR unirradiated fuel element shipping container was designed and fabricated at the Oak Ridge National Laboratory for the transport of HFIR unirradiated fuel elements. The container was evaluated analytically and experimentally to determine its compliance with the applicable regulations governing containers in which radioactive and fissile materials are transported, and the evaluation is the subject of this report. Computational and test procedures were used to determine the structural integrity and thermal behavior of the cask relative to the general standards for normal conditions of transport and the standards for the hypothetical accident conditions. The results of the evaluation demonstrate that the container is in compliance with the applicable regulations

Rail Safety/Equipment Crashworthiness : Volume 3. Proposed Engineering Standards.

Science.gov (United States)

1978-07-01

The document, the third of four volumes, contains recommended Engineering Standards prepared in the format of the standards published in the Code of Federal Regulations (Title 49, Transportation, Parts 200). The standards proposed provide improved oc...

7 CFR 29.3182 - Key to standard grademarks.

Science.gov (United States)

2010-01-01

... Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE COMMODITY STANDARDS AND STANDARD CONTAINER.... Groups X—Flyings. C—Lugs or Cutters B—Leaf. T—Tips. M—Mixed. N—Nondescript. S—Scrap. Qualities 1—Choice...

Making operations on standard-library containers strongly exception safe

DEFF Research Database (Denmark)

Katajainen, Jyrki

2007-01-01

-library containers to provide the strong guarantee of exception safety, instead of the default guarantee, without violating the stringent performance requirements specified in the C++ standard. In particular, we show that every strongly exception-safe operation on dynamic arrays and ordered dictionaries is only...... a constant factor slower than the corresponding default-guarantee operation. In terms of the amount of space, the overhead introduced is linear in the number of elements stored....

18 CFR 3c.1 - Cross-reference to employee ethical conduct standards and financial disclosure regulations.

Science.gov (United States)

2010-04-01

... employee ethical conduct standards and financial disclosure regulations. 3c.1 Section 3c.1 Conservation of... STANDARDS OF CONDUCT § 3c.1 Cross-reference to employee ethical conduct standards and financial disclosure... branch-wide financial disclosure regulations at 5 CFR part 2634, the Standards of Ethical Conduct for...

Evaluation on applicability of the rules, regulations, and industrial codes and standards for SMART development

International Nuclear Information System (INIS)

Choi, Suhn; Lee, C C.; Lee, C.K.; Kim, K.K.; Kim, J.P.; Kim, J.H.; Cho, B.H.; Kang, D J.; Bae, G.H.; Chung, M.; Chang, M.H.

1999-03-01

In this report, evaluation on applicability of the rules, regulations, and industrial codes and standards for SMART has been made. As the first step, past-to-present status of licensing structures were reviewed. Then, the rules, regulations, and standards applied to YGN 3-6 were listed and reviewed. Finally, evaluation on applicability of such rules and standards for SMART are made in each design fields. During this step technical evaluations on each items of rules, regulations and standards are made and the possible remedies or comments are suggested. The results are summarized in a tabular form and enclosed as Appendix. (Author). 8 refs., 5 tabs., 3 figs

FDA regulations regarding iodine addition to foods and labeling of foods containing added iodine12

Science.gov (United States)

Trumbo, Paula R

2016-01-01

The US Food and Drug Administration (FDA) regulates the addition of iodine to infant formulas, the iodization of salt, and the addition of salt and iodine to foods. The required amount of iodine in infant formulas is based on caloric content, and the label must provide the iodine content per 100 kcal. Cuprous iodide and potassium iodide may be added to table salt as a source of dietary iodine at a maximum amount of 0.01%; if added, the label must indicate that the salt is iodized. Table salt to which iodine has not been added must bear the statement, “This salt does not supply iodide, a necessary nutrient.” If a nutrient is to be appropriately added to a food for the purpose of correcting a dietary insufficiency, there should be sufficient scientific information available to demonstrate a nutritional deficiency and/or identify a public health problem. Furthermore, the population groups that would benefit from the proposed fortification should be identified. If iodine is added to a food, the percent Daily Value of iodine must be listed. There are no FDA regulations governing ingredient standards for dietary supplements. As a result, some dietary supplements include iodine and others do not. If a supplement contains iodine, the Supplement Facts label must list iodine as a nutrient ingredient. If iodine is not listed on the Supplement Facts label, then it has not been added. There are similarities between the FDA, which establishes US food regulations and policies, and the Codex Alimentarius (Codex), which develops international food standards and guidelines under the aegis of the FAO and the WHO. Both the FDA and Codex call for the labeling of table salt to indicate fortification with iodine, voluntary labeling of iodine on foods, and a Daily Value (called a Nutrient Reference Value by Codex) of 150 μg for iodine. PMID:27534626

Regulations, guidelines, standards, and policies pertaining to decontamination and decommissioning activities: A literature review. Informal report, Revision 1

International Nuclear Information System (INIS)

Cowgill, M.G.

1994-09-01

A literature review of the existing rules, regulations, and guidelines pertaining to the decontamination and decommissioning of nuclear facilities has been updated. Included in the survey are US Government documents, national (industrial) standards, international standards and guidelines, and the regulations issued by various national governments, such as the United Kingdom, Canada, and Germany. The Department of Energy (DOE) complex contains within it almost 1,000 nuclear facilities which will require decommissioning in the coming years. This action will entail activities in many different areas, one of which will involve the development of the basic safety principles to be applied to the process as a whole. These principles will be used to guide personnel in the development of safety assessment procedures for decontamination and decommissioning (D and D) activities and in conducting safety assessments of such activities at the facilities themselves. The present report represents an updating of the original report. It retains all the information that appeared in the original report with the new material integrated into the applicable sections. Future revisions will be made as additional information becomes available

Regulations, guidelines, standards, and policies pertaining to decontamination and decommissioning activities: A literature review

International Nuclear Information System (INIS)

Cowgill, M.G.

1993-09-01

A literature review has been conducted of the existing rules, regulations, and guidelines pertaining to the decontamination and decommissioning of nuclear facilities. Included in the survey are US Government documents, national (industrial) standards, international standards and guidelines, and the regulations issued by various national governments, such as the United Kingdom, Canada, and Germany

Benefit using reasonable regulations in USA, how to skill up on professional engineers, apply international code, standard, and regulation

International Nuclear Information System (INIS)

Turner, S.L.; Morokuzu, Muneo; Amano, Osamu

2005-01-01

The reasonable regulations in USA consist of a graduated approach and a risk informed approach (RIA). RIA rationalizes the regulations on the basis of data of operations etc. PSA (Probabilistic Safety Assessment), a general method of RIA, is explained in detail. The benefits of nuclear power plant using RIA are increase of the rate of operation, visualization of risk, application of design standard and design, cost down of nuclear fuel cycle, waste, production and operation, and safety. RIA is supported by the field data, code, standard, regulation and professional engineers. The effects of introduction of RIA are explained. In order to introduce RIA in Japan, all the parties concerned such as the regulation authorities, the electric power industries, makers, universities, have to understand it and work together. A part of scientific society is stated. (S.Y.)

7 CFR 29.2481 - Key to standard grademarks.

Science.gov (United States)

2010-01-01

... Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE COMMODITY STANDARDS AND STANDARD CONTAINER.... 3—Good. 4—Fair. 5—Low. Colors L—Light brown. F—Medium brown. D—Dark brown. M—Mixed or variegated. G...

7 CFR 29.2696 - Key to standard grademarks.

Science.gov (United States)

2010-01-01

... Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE COMMODITY STANDARDS AND STANDARD CONTAINER.... 3—Good. 4—Fair. 5—Low. Colors L—Light brown. F—Medium brown. D—Dark brown. M—Mixed or variegates. VF...

Regulations and standardization relative to the biomass combustion

International Nuclear Information System (INIS)

Autret, E.

2009-01-01

It does not exist regulations on pollutants emissions on domestic wood burning furnaces, however, these appliances are submitted to the European and french standardization concerning the safety rules, the use rules and the tests methods. Since 2007, these wood burning appliances on the market must have the European Community label. The green flame label was elaborated by the environment and energy control Agency (A.D.E.M.E.), and manufacturers of domestic appliances to promote the use of competitive wood burning appliances. concerning the collective and industrial heating, the installations of more 2 MW are framed by different categories of the installations classified for environment protection (I.C.P.E.) regulation according their fuel and power. The combustion installations of less than 2 MW are a particular case, they are framed by a sanitary department regulation and are controlled by the department directions of sanitary and social affairs. the limit values of emissions are summarized in tables. (N.C.)

Nanometrology, Standardization and Regulation of Nanomaterials in Brazil: A Proposal for an Analytical-Prospective Model

Directory of Open Access Journals (Sweden)

Ana Rusmerg Giménez Ledesma

2013-05-01

Full Text Available The main objective of this paper is to propose an analytical-prospective model as a tool to support decision-making processes concerning metrology, standardization and regulation of nanomaterials in Brazil, based on international references and ongoing initiatives in the world. In the context of nanotechnology development in Brazil, the motivation for carrying out this research was to identify potential benefits of metrology, standardization and regulation of nanomaterials production, from the perspective of future adoption of the model by the main stakeholders of development of these areas in Brazil. The main results can be summarized as follows: (i an overview of international studies on metrology, standardization and regulation of nanomaterials, and nanoparticles, in special; (ii the analytical-prospective model; and (iii the survey questionnaire and the roadmapping tool for metrology, standardization and regulation of nanomaterials in Brazil, based on international references and ongoing initiatives in the world.

7 CFR 29.3686 - Key to standard grademarks.

Science.gov (United States)

2010-01-01

... Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE COMMODITY STANDARDS AND STANDARD CONTAINER... 3—Good R—Reddish brown X—Lugs 4—Fair D—Dark brown N—Nondescript 5—Low M—Mixed S—Scrap G—Green [30 FR...

25 CFR 1000.464 - What personal conflicts of interest must the standards of conduct regulate?

Science.gov (United States)

2010-04-01

... conduct regulate? 1000.464 Section 1000.464 Indians OFFICE OF THE ASSISTANT SECRETARY, INDIAN AFFAIRS... interest must the standards of conduct regulate? The personal conflicts of interest standards must: (a... financial interest or an employment relationship; (b) Prohibit such officers, employees, or agents from...

78 FR 12005 - Regulation of Fuels and Fuel Additives: 2013 Renewable Fuel Standards; Public Hearing

Science.gov (United States)

2013-02-21

... Regulation of Fuels and Fuel Additives: 2013 Renewable Fuel Standards; Public Hearing AGENCY: Environmental... EPA is announcing a public hearing to be held for the proposed rule ``Regulation of Fuels and Fuel Additives: 2013 Renewable Fuel Standards,'' which was published separately in the Federal Register on...

Metal-Containing Polystyrene Beads as Standards for Mass Cytometry.

Science.gov (United States)

Abdelrahman, Ahmed I; Ornatsky, Olga; Bandura, Dmitry; Baranov, Vladimir; Kinach, Robert; Dai, Sheng; Thickett, Stuart C; Tanner, Scott; Winnik, Mitchell A

2010-01-01

We examine the suitability of metal-containing polystyrene beads for the calibration of a mass cytometer instrument, a single particle analyser based on an inductively coupled plasma ion source and a time of flight mass spectrometer. These metal-containing beads are also verified for their use as internal standards for this instrument. These beads were synthesized by multiple-stage dispersion polymerization with acrylic acid as a comonomer. Acrylic acid acts as a ligand to anchor the metal ions within the interior of the beads. Mass cytometry enabled the bead-by-bead measurement of the metal-content and determination of the metal-content distribution. Beads synthesized by dispersion polymerization that involved three stages were shown to have narrower bead-to-bead variation in their lanthanide content than beads synthesized by 2-stage dispersion polymerization. The beads exhibited insignificant release of their lanthanide content to aqueous solutions of different pHs over a period of six months. When mixed with KG1a or U937 cell lines, metal-containing polymer beads were shown not to affect the mass cytometry response to the metal content of element-tagged antibodies specifically attached to these cells.

Production of Cellulases by Rhizopus stolonifer from Glucose-Containing Media Based on the Regulation of Transcriptional Regulator CRE.

Science.gov (United States)

Zhang, Yingyiing; Tang, Bin; Du, Guocheng

2017-03-28

Carbon catabolite repression is a crucial regulation mechanism in microorganisms, but its characteristic in Rhizopus is still unclear. We extracted a carbon regulation gene, cre , that encoded a carbon catabolite repressor protein (CRE) from Rhizopus stolonifer TP-02, and studied the regulation of CRE by real-time qPCR. CRE responded to glucose in a certain range, where it could significantly regulate part of the cellulase genes ( eg, bg, and cbh2 ) without cbh1 . In the comparison of the response of cre and four cellulase genes to carboxymethylcellulose sodium and a simple carbon source (lactose), the effect of CRE was only related to the concentration of reducing sugars. By regulating the reducing sugars to range from 0.4% to 0.6%, a glucose-containing medium with lactose as the inducer could effectively induce cellulases without the repression of CRE. This regulation method could potentially reduce the cost of enzymes produced in industries and provide a possible solution to achieve the large-scale synthesis of cellulases.

28 CFR 45.1 - Cross-reference to ethical standards and financial disclosure regulations.

Science.gov (United States)

2010-07-01

... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Cross-reference to ethical standards and...) EMPLOYEE RESPONSIBILITIES § 45.1 Cross-reference to ethical standards and financial disclosure regulations. Employees of the Department of Justice are subject to the executive branch-wide Standards of Ethical Conduct...

29 CFR 2703.1 - Cross-reference to employee ethical conduct standards and financial disclosure regulations.

Science.gov (United States)

2010-07-01

... 29 Labor 9 2010-07-01 2010-07-01 false Cross-reference to employee ethical conduct standards and...-reference to employee ethical conduct standards and financial disclosure regulations. Members and employees... of Ethical Conduct at 5 CFR part 2635; the Commission's regulations at 5 CFR part 8401, which...

25 CFR 900.235 - What personal conflicts of interest must the standards of conduct regulate?

Science.gov (United States)

2010-04-01

... conduct regulate? 900.235 Section 900.235 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR... must the standards of conduct regulate? The standards must prohibit an officer, employee, or agent... involving an entity in which such persons have a direct financial interest or an employment relationship. It...

20 CFR 726.103 - Application for authority to self-insure; effect of regulations contained in this part.

Science.gov (United States)

2010-04-01

... § 726.103 Application for authority to self-insure; effect of regulations contained in this part. As... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Application for authority to self-insure; effect of regulations contained in this part. 726.103 Section 726.103 Employees' Benefits EMPLOYMENT...

Regulation and practice of workers' protection from chemical exposures during container handling

DEFF Research Database (Denmark)

Nørgaard Fløe Pedersen, Randi; Jepsen, Jørgen Riis; Ádám, Balázs

2014-01-01

instructions relate to container handling, the provided information is not sufficiently detailed to conduct safe practice in many aspects. In accordance with the scientific literature, the interviewees estimate that there is a high frequency (5 to 50%) of containers with hazardous chemical exposure......Background: Fumigation of freight containers to prevent spread of pests and off-gassing of freight are sources of volatile chemicals that may constitute significant health risks when released. The aim of the study was to investigate the regulation and practice of container handling in Denmark...... with focus on preventive measures to reduce risk of chemical exposure. Methods: A comprehensive systematic search of scientific literature, legislation and recommendations related to safe work with transport containers from international and Danish regulatory bodies was performed. The practice of handling...

78 FR 277 - Section 610 Review of NPDES Permit Regulation and Effluent Limitations Guidelines Standards for...

Science.gov (United States)

2013-01-03

..., Section 610 Review of NPDES Permit Regulation and Effluent Limitations Guidelines Standards for..., FRL-9764-8] Section 610 Review of NPDES Permit Regulation and Effluent Limitations Guidelines Standards for Concentrated Animal Feeding Operations (CAFOs); Extension of Comment Period AGENCY...

12 CFR 264.101 - Cross-reference to employees' ethical conduct standards and financial disclosure regulations.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 3 2010-01-01 2010-01-01 false Cross-reference to employees' ethical conduct... § 264.101 Cross-reference to employees' ethical conduct standards and financial disclosure regulations... branch-wide standards of ethical conduct at 5 CFR part 2635 and the Board's regulation at 5 CFR part 6801...

78 FR 13675 - Federal Acquisition Regulation; Submission for OMB Review; Cost Accounting Standards Administration

Science.gov (United States)

2013-02-28

...; Submission for OMB Review; Cost Accounting Standards Administration AGENCY: Department of Defense (DOD... collection requirement concerning cost accounting standards administration. A notice was published in the...- 0129, Cost Accounting Standards Administration by any of the following methods: Regulations.gov : http...

Comparison report on OECD-CSNI containment standard problem N.1

International Nuclear Information System (INIS)

Winkler, W.

1980-05-01

The technical purpose of this containment standard problem N.1 was to compare experimental results of history of pressure, temperature, pressure difference and water mass after a steam line rupture within a chain of six subsequent compartments (simplified integral test) with the corresponding results of best-estimate post-test calculations from computer codes for three different time intervals. 11 countries took part in the comparison, using 11 different computer codes and several versions

Multi-objective regulations on transportation fuels: Comparing renewable fuel mandates and emission standards

International Nuclear Information System (INIS)

Rajagopal, D.; Plevin, R.; Hochman, G.; Zilberman, D.

2015-01-01

We compare two types of fuel market regulations — a renewable fuel mandate and a fuel emission standard — that could be employed to simultaneously achieve multiple outcomes such as reduction in fuel prices, fuel imports and greenhouse gas (GHG) emissions. We compare these two types of regulations in a global context taking into account heterogeneity in carbon content of both fossil fuels and renewable fuels. We find that although neither the ethanol mandate nor the emission standard is certain to reduce emissions relative to a business-as-usual baseline, at any given level of biofuel consumption in the policy region, a mandate, relative to an emission standard, results in higher GHG emissions, smaller expenditure on fuel imports, lower price of ethanol-blended gasoline and higher domestic fuel market surplus. This result holds over a wide range of values of model parameters. We also discuss the implications of this result to a regulation such as the US Renewable Fuel Standard given recent developments within the US such as increase in shale and tight oil production and large increase in average vehicle fuel economy of the automotive fleet. - Highlights: • Biofuel mandates and fuel GHG emission standards are analyzed from a multiple criteria perspective • An emission-standard always results in lower global emissions while requiring less biofuel relative to a biofuel mandate • An emission-standard results in higher fuel price in the home region relative to a biofuel mandate • Emission standards lead to more shuffling of both fossil fuels and biofuels between home and abroad • The relative impact of the policies on fuel imports depends on the relative cost-effectiveness of domestic & imported biofuel • Recent developments oil production and fuel economy increase the net benefits of an LCFS approach relative to RFS

The United States Board on Geographic Names: Standardization or regulation?

Science.gov (United States)

Payne, R.L.

2000-01-01

The United States Board on Geographic Names was created in 1890 to standardize the use of geographic names on federal maps and documents, and was established in its present form in 1947 by public law. The Board is responsible for geographic name usage and application throughout the federal government and its members must approve a name change or new name before it can be applied to federal maps and publications. To accomplish its mission, the Board has developed principles, policies, and procedures for use in the standardization process. The Board is also responsible legally for the promulgation of standardized names, whether or not these names have ever been controversial, and today this is accomplished by the universal availability of electronic databases for domestic and foreign names. This paper examines the development of Board policies and the implementation of these policies to achieve standardization with a view to relating these policies and activities to questions of standardization or regulation. ?? 2000 by The American Name Society.

36 CFR 1011.3 - Do these regulations adopt the Federal Claims Collections Standards?

Science.gov (United States)

2010-07-01

... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Do these regulations adopt... PRESIDIO TRUST DEBT COLLECTION General Provisions § 1011.3 Do these regulations adopt the Federal Claims Collections Standards? This part adopts and incorporates all provisions of the FCCS. This part also...

29 CFR 0.735-1 - Cross-references to employee ethical conduct standards, financial disclosure regulations and...

Science.gov (United States)

2010-07-01

... 29 Labor 1 2010-07-01 2010-07-01 true Cross-references to employee ethical conduct standards, financial disclosure regulations and other ethics regulations. 0.735-1 Section 0.735-1 Labor Office of the Secretary of Labor ETHICS AND CONDUCT OF DEPARTMENT OF LABOR EMPLOYEES Standards of Conduct for Current...

Standard contract terms regulation in the proposal for a common European sales law

NARCIS (Netherlands)

Loos, M.B.M.

2012-01-01

In this paper, the regulation in standard contract terms in the proposal for a Commono European Sales Law (CESL) is compared with the regulation in the Unfair Terms Directive, the Draft Common Frame of Reference (DCFR) and the Vienna Sales Convention (CISG). The paper starts with an overview of the

Gasoline risk management: a compendium of regulations, standards, and industry practices.

Science.gov (United States)

Swick, Derek; Jaques, Andrew; Walker, J C; Estreicher, Herb

2014-11-01

This paper is part of a special series of publications regarding gasoline toxicology testing and gasoline risk management; this article covers regulations, standards, and industry practices concerning gasoline risk management. Gasoline is one of the highest volume liquid fuel products produced globally. In the U.S., gasoline production in 2013 was the highest on record (API, 2013). Regulations such as those pursuant to the Clean Air Act (CAA) (Clean Air Act, 2012: § 7401, et seq.) and many others provide the U.S. federal government with extensive authority to regulate gasoline composition, manufacture, storage, transportation and distribution practices, worker and consumer exposure, product labeling, and emissions from engines and other sources designed to operate on this fuel. The entire gasoline lifecycle-from manufacture, through distribution, to end-use-is subject to detailed, complex, and overlapping regulatory schemes intended to protect human health, welfare, and the environment. In addition to these legal requirements, industry has implemented a broad array of voluntary standards and best management practices to ensure that risks from gasoline manufacturing, distribution, and use are minimized. Copyright © 2014 The Authors. Published by Elsevier Inc. All rights reserved.

13 CFR 105.101 - Cross-reference to employee ethical conduct standards and financial disclosure regulations.

Science.gov (United States)

2010-01-01

... ethical conduct standards and financial disclosure regulations. 105.101 Section 105.101 Business Credit... RESPONSIBILITIES Standards of Conduct § 105.101 Cross-reference to employee ethical conduct standards and financial... to the Standards of Ethical Conduct for Employees of the Executive Branch at 5 CFR part 2635 and the...

Automotive emission standards. (Latest citations from Pollution Abstracts). Published Search

International Nuclear Information System (INIS)

1993-07-01

The bibliography contains citations concerning emission standards and air quality standards applied to automobile emissions. Included are federal and state regulations and policies regarding these emission standards. Techniques to meet emission standards are also addressed, involving fuel injection, catalysts, alternate engines, and automotive fuel refinery operations. Studies concerning implementation of automobile emission standards explore economic and environmental effects, testing and inspection procedures, and the automobile industry point of view. Most of the citations refer to gasoline engines, but a few pertain to diesel and other fuels. (Contains 250 citations and includes a subject term index and title list.)

Regulations for pressurized equipment in the European Single Market - construction of steam boilers, containers and pipelines

International Nuclear Information System (INIS)

Grassmuck, J.

1992-01-01

The impulses produced by the data of the standardized EC Single Market have now reached pressurized equipment in the field of EC Guidelines and European standardisation. This must be regarded as a great challenge to the interested and concerned parties. All efforts to represent the interested parties in European Committees must be made. In order to reach the goal quickly and successfully, a considerable readiness to compromise is, however, necessary. At the end of the development process, a comprehensible, standardized set of regulations will be available for pressurized equipment throughout Europe. The regulations will consist of national ones converted into European Guidelines and Standards. (orig.) [de

Survey of Regulations Applicable to the Finned Containment in Korean Nuclear Power Plant for Light Water Reactor

International Nuclear Information System (INIS)

Noh, Hyung Gyun; Kang, Hie Chan

2016-01-01

In severe accident, the molten corium would discharge into the reactor cavity and interact with water and concrete of cavity. Molten corium includes non-oxidation metals such as Zr, Fe and Cr. These metal species reacted with water emit hydrogen gas. In addition to this, a mount of steam can be emitted to the containment such as steam line break accident. As a result, steam and hydrogen gas can pressurize containment over the design pressure and threaten its integrity. For this reasons, a concept equipped with finned on the containment building was proposed for coping with prolonged accident. Finned containment can enhance heat transfer to the ambient, and the building itself is working as a heat sink. Multiple metal fins and metal rod are penetrated into containment wall, and the rods are working as an additional path of heat removal. To be accepted in the nuclear power plants, this configuration should satisfy the requirement of heat removal and follow all regulations related with containment also. For applying to Korean nuclear power plants, the finned containment should follow all regulations specialized in Korea such as Nuclear regulatory criteria for light water reactor and Guidelines of nuclear safety examination for light water reactor. A concept of containment as a passive cooling system has been proposed. Furthermore, the new containment concept can be applied on the real containment which satisfies the various regulations. Finned containment would be expected positive effects on heat removal from the containment. If the fins are properly welded to the liner, finned containment could satisfy the leak tightness and prevention of external influences. Finned containment could be favorable to protect external impact like aircraft crash because of the additional structural integrity by the fins

Survey of Regulations Applicable to the Finned Containment in Korean Nuclear Power Plant for Light Water Reactor

Energy Technology Data Exchange (ETDEWEB)

Noh, Hyung Gyun [Pohang University, Pohang (Korea, Republic of); Kang, Hie Chan [Kunsan University, Gunsan (Korea, Republic of)

2016-05-15

In severe accident, the molten corium would discharge into the reactor cavity and interact with water and concrete of cavity. Molten corium includes non-oxidation metals such as Zr, Fe and Cr. These metal species reacted with water emit hydrogen gas. In addition to this, a mount of steam can be emitted to the containment such as steam line break accident. As a result, steam and hydrogen gas can pressurize containment over the design pressure and threaten its integrity. For this reasons, a concept equipped with finned on the containment building was proposed for coping with prolonged accident. Finned containment can enhance heat transfer to the ambient, and the building itself is working as a heat sink. Multiple metal fins and metal rod are penetrated into containment wall, and the rods are working as an additional path of heat removal. To be accepted in the nuclear power plants, this configuration should satisfy the requirement of heat removal and follow all regulations related with containment also. For applying to Korean nuclear power plants, the finned containment should follow all regulations specialized in Korea such as Nuclear regulatory criteria for light water reactor and Guidelines of nuclear safety examination for light water reactor. A concept of containment as a passive cooling system has been proposed. Furthermore, the new containment concept can be applied on the real containment which satisfies the various regulations. Finned containment would be expected positive effects on heat removal from the containment. If the fins are properly welded to the liner, finned containment could satisfy the leak tightness and prevention of external influences. Finned containment could be favorable to protect external impact like aircraft crash because of the additional structural integrity by the fins.

34 CFR 73.1 - Cross-reference to employee ethical conduct standards and financial disclosure regulations.

Science.gov (United States)

2010-07-01

... 34 Education 1 2010-07-01 2010-07-01 false Cross-reference to employee ethical conduct standards... of Education STANDARDS OF CONDUCT § 73.1 Cross-reference to employee ethical conduct standards and... branch-wide Standards of Ethical Conduct at 5 CFR part 2635 and to the Department of Education regulation...

76 FR 38153 - California State Nonroad Engine Pollution Control Standards; Commercial Harbor Craft Regulations...

Science.gov (United States)

2011-06-29

... Standards; Commercial Harbor Craft Regulations; Opportunity for Public Hearing and Comment AGENCY... engines on commercial harbor craft. CARB has requested that EPA issue a new authorization under [email protected] . SUPPLEMENTARY INFORMATION: I. California's Commercial Harbor Craft Regulations In a...

46 CFR 508.101 - Cross-referrence to employee ethical conduct standards and financial disclosure regulations.

Science.gov (United States)

2010-10-01

... 46 Shipping 9 2010-10-01 2010-10-01 false Cross-referrence to employee ethical conduct standards... GENERAL AND ADMINISTRATIVE PROVISIONS EMPLOYEE ETHICAL CONDUCT STANDARDS AND FINANCIAL DISCLOSURE REGULATIONS § 508.101 Cross-referrence to employee ethical conduct standards and financial disclosure...

Analysis and design of a standardized control module for switching regulators

Science.gov (United States)

Lee, F. C.; Mahmoud, M. F.; Yu, Y.; Kolecki, J. C.

1982-07-01

Three basic switching regulators: buck, boost, and buck/boost, employing a multiloop standardized control module (SCM) were characterized by a common small signal block diagram. Employing the unified model, regulator performances such as stability, audiosusceptibility, output impedance, and step load transient are analyzed and key performance indexes are expressed in simple analytical forms. More importantly, the performance characteristics of all three regulators are shown to enjoy common properties due to the unique SCM control scheme which nullifies the positive zero and provides adaptive compensation to the moving poles of the boost and buck/boost converters. This allows a simple unified design procedure to be devised for selecting the key SCM control parameters for an arbitrarily given power stage configuration and parameter values, such that all regulator performance specifications can be met and optimized concurrently in a single design attempt.

Drug evaluation and the permissive principle: continuities and contradictions between standards and practices in antidepressant regulation.

Science.gov (United States)

Abraham, John; Davis, Courtney

2009-08-01

Pharmaceuticals are not permitted on to the market unless they are granted regulatory approval. The regulatory process is, therefore, crucial in whether or not a drug is widely prescribed. Regulatory agencies have developed standards of performance that pharmaceuticals are supposed to meet before entering the market. Regulation of technologies is often discussed by reference to the precautionary principle. In contrast, this paper develops the concept of the 'permissive principle' as a way of understanding the departure of regulators' practices from standards of drug efficacy to which regulatory agencies themselves subscribe. By taking a case study of antidepressant regulation in the UK and the USA, the mechanisms of permissive regulatory practices are examined. An STS methodology of both spatial (international) and temporal comparisons of regulatory practices with regulatory standards is employed to identify the nature and extent of the permissive regulation. It is found that the permissive principle was adopted by drug regulators in the UK and the USA, but more so by the former than the latter. Evidently, permissive regulation, which favours the commercial interests of the drug manufacturer, but is contrary to the interests of patients, may penetrate to the heart of regulatory science. On the other hand, permissive regulation of specific drugs should not be regarded as an inevitable result of marketing strategies and concomitant networks deployed by powerful pharmaceutical companies, because the extent of permissive regulation may vary according to the intra-institutional normative commitments of regulators to uphold their technical standards against the commercial interests of the manufacturer. Likely sociological factors that can account for such permissive regulatory practices are 'corporate bias', secrecy and excessive regulatory trust in the pharmaceutical industry in the UK, political expediency and ideological capture in the USA, combined in both countries

75 FR 3236 - Federal Acquisition Regulation; Submission for OMB Review; Cost Accounting Standards Administration

Science.gov (United States)

2010-01-20

... extension of a previously approved information collection requirement concerning cost accounting standards... include pertinent rules and regulations related to the Cost Accounting Standards along with necessary... impact estimates and descriptions in cost accounting practices and also to provide information on CAS...

Status of Recent Developments in the Technical Standards of Japan

International Nuclear Information System (INIS)

Ahn, Hyung-Joon; Ahn, Sang-Kyu; Koh, Jae-Dong; Kim, Chang-Bum

2006-01-01

Japan has systematically revamped its technical standards for nuclear reactor facilities by formulating various performance regulations. Being part of a trend toward deregulation, such efforts toward social regulation is aimed at effectively operating administrative procedural laws to keep pace with global trends and enhance the benefits of deregulation under the principle of self-responsibility. Based on the collection of public opinions in February and March 2005, the Nuclear and Industrial Safety Agency(NISA) presented its position that it was required to promptly perform a flexible assessment of the technical feasibility of formulated society and association standards. Current, pressing issues are summarized as an early revision of technical standards regarding nuclear facilities for power generation, use of society and association standards, and the overhaul of nuclear safety regulations subject to performance regulations. Subjecting technical standards to performance regulations means stipulating the qualitative aspects of performance and the targets that certain facilities must achieve, which are not specific standards, but general compulsory standards. This study examines the early revision of technical standards on nuclear facilities for power generation and the status of the use of society and association standards, as well as introducing the details of revisions in the concrete containment vessel standards as specific examples

29 CFR 1600.101 - Cross-reference to employee ethical conduct standards and financial disclosure regulations.

Science.gov (United States)

2010-07-01

... 29 Labor 4 2010-07-01 2010-07-01 false Cross-reference to employee ethical conduct standards and... to employee ethical conduct standards and financial disclosure regulations. Employees of the Equal Employment Opportunity Commission (EEOC) are subject to the executive branch-wide Standards of Ethical...

75 FR 37733 - Regulation of Fuels and Fuel Additives: Modifications to Renewable Fuel Standard Program

Science.gov (United States)

2010-06-30

... Regulation of Fuels and Fuel Additives: Modifications to Renewable Fuel Standard Program AGENCY... direct final rule to amend the Renewable Fuel Standard program requirements on May 10, 2010. Because EPA... Fuel Standard program requirements, published on May 10, 2010. We stated in that direct final rule that...

Restructuring of technical standards for regulation of nuclear power plants in Japan

International Nuclear Information System (INIS)

Takehiko Nakamura; Masahiro Aoki; Kiyoshi Takasaka; Yukio Hirano; Eiji Hiraoka; Mikio Kurihara; Junichi Morita; Zenichi Ogiso; Yoshihiko Nishiwaki

2005-01-01

Regulatory requirements for nuclear power plants (NPPs) have been reviewed and restructured in Japan, in order to accommodate recent technical progress in a timely manner. In this new regulatory process, the governmental technical requirements are modified to performance specifications and the consensus codes and standards established by academic and public societies are being used as prescriptive specifications to realize the performance. As a first step, a fitness-rule to evaluate structural integrity of the components having cracks was introduced into the Japanese regulatory rules in Oct. 2003. 'Rules on Fitness-for-Service for Nuclear Power Plants' by the Japan Society of Mechanical Engineers (JSME) was utilized as a prescriptive specification for in-service-inspections and for the integrity evaluation of the components with stress corrosion cracks and fatigue cracks. The process is being extended to other requirements for structural design and construction of mechanical components and concrete containments, as well as requirements for welding. Prescriptive specifications for the requirements by the JSME and other consensus codes have been technically reviewed by a regulatory body, the Nuclear and Industrial Safety Agency, and specified as regulatory standards for the licensing procedure. In the course of the review, consistency and coverage of the requirements were examined against the Safety Design Guidelines by the Nuclear Safety Commission and the safety requirements for design of nuclear power plant by the International Atomic Energy Agency, NS-R-1. Additional requirements against the stress corrosion cracking, hydrogen accumulation, high-cycle thermal fatigue, etc. are being specified in the requirements to prevent troubles experienced in NPPs in Japan and overseas. This paper describes outlines of the on-going activities restructuring the technical standards for regulation of NPPs in Japan. (authors)

Standards and guidelines should be rules between licensees and regulators

International Nuclear Information System (INIS)

Narabayashi, Tadashi

2014-01-01

The 2011 off the Pacific coast of Tohoku Pacific Earthquake and the Tsunami gave the serious damage to the Fukushima-Daiichi Nuclear Power Plants (NPPs). The accidents occurred in Unit 1, 2, 3 and 4. It is said that the height of tsunami attacked Fukushima NPP was more than 14m. After 50 minutes from the automatic shut-down, tsunami attacked the NPPs in Fukushima Daiichi NPPs. For example, the Unit 1 lost A/C power caused the loss of water injection function; it made the core meltdown and unusual increase of PCV pressure in the midnight of March 11th to 12th morning. Though the Unit one has the Isolation Condenser Core Cooling system, it was stopped by the operator to keep the cooling rate of 55degC/h. Finally, the isolation signal was transmitted from the control room to the motor driven isolation valves when the control room's battery discharged. It was the initiation of the core meltdown. The lessons from the accidents, we should improve the nuclear safety regulation through the innovation of regulatory rules and safety standards. Standards and guidelines should be rules between licensees and regulators. (author)

Law regulations concerning food supplements, dietetic food and novel food containing herbal substances

Directory of Open Access Journals (Sweden)

Baraniak Justyna

2016-12-01

Full Text Available Food supplements are concentrated sources of nutrients and/or other substances with a nutritional or physiological effect. However, they often contain herbal substances or their preparations. Food supplements belong to category of food and for that reason are regulated by food legislation. European Union regulations and directives established general directions for dietary supplements, dietetic food, which due to their special composition or manufacturing process are prepared for specific groups of people with special nutritional needs, and novel food/novel food ingredients to ensure product safety, suitability and appropriate consumer information.

15 CFR 19.3 - Do these regulations adopt the Federal Claims Collection Standards (FCCS)?

Science.gov (United States)

2010-01-01

... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Do these regulations adopt the Federal... of Commerce COMMERCE DEBT COLLECTION General Provisions § 19.3 Do these regulations adopt the Federal Claims Collection Standards (FCCS)? This Part adopts and incorporates all provisions of the FCCS. This...

31 CFR 5.3 - Do these regulations adopt the Federal Claims Collection Standards (FCCS)?

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 1 2010-07-01 2010-07-01 false Do these regulations adopt the... Secretary of the Treasury TREASURY DEBT COLLECTION General Provisions § 5.3 Do these regulations adopt the Federal Claims Collection Standards (FCCS)? This part adopts and incorporates all provisions of the FCCS...

To recognize the use of international standards for making harmonized regulation of medical devices in Asia-pacific.

Science.gov (United States)

Anand, K; Saini, Ks; Chopra, Y; Binod, Sk

2010-07-01

'Medical Devices' include everything from highly sophisticated, computerized, medical equipment, right down to simple wooden tongue depressors. Regulations embody the public expectations for how buildings and facilities are expected to perform and as such represent public policy. Regulators, who develop and enforce regulations, are empowered to act in the public's interest to set this policy and are ultimately responsible to the public in this regard. Standardization contributes to the basic infrastructure that underpins society including health and environment, while promoting sustainability and good regulatory practice. The international organizations that produce International Standards are the International Electrotechnical Commission (IEC), the International Organization for Standardization (ISO), and the International Telecommunication Union (ITU). With the increasing globalization of markets, International Standards (as opposed to regional or national standards) have become critical to the trading process, ensuring a level playing field for exports, and ensuring that imports meet the internationally recognized levels of performance and safety. The development of standards is done in response to sectors and stakeholders that express a clearly established need for them. An industry sector or other stakeholder group typically communicates its requirement for standards to one of the national members. To be accepted for development, a proposed work item must receive a majority support of the participating members, who verify the global relevance of the proposed item. The regulatory authority (RA) should provide a method for the recognition of international voluntary standards and for public notification of such recognition. The process of recognition may vary from country to country. Recognition may occur by periodic publication of lists of standards that a regulatory authority has found will meet the Essential Principles. In conclusion, International standards

Proteomic Analysis Reveals the Leaf Color Regulation Mechanism in Chimera Hosta "Gold Standard" Leaves.

Science.gov (United States)

Yu, Juanjuan; Zhang, Jinzheng; Zhao, Qi; Liu, Yuelu; Chen, Sixue; Guo, Hongliang; Shi, Lei; Dai, Shaojun

2016-03-08

Leaf color change of variegated leaves from chimera species is regulated by fine-tuned molecular mechanisms. Hosta "Gold Standard" is a typical chimera Hosta species with golden-green variegated leaves, which is an ideal material to investigate the molecular mechanisms of leaf variegation. In this study, the margin and center regions of young and mature leaves from Hosta "Gold Standard", as well as the leaves from plants after excess nitrogen fertilization were studied using physiological and comparative proteomic approaches. We identified 31 differentially expressed proteins in various regions and development stages of variegated leaves. Some of them may be related to the leaf color regulation in Hosta "Gold Standard". For example, cytosolic glutamine synthetase (GS1), heat shock protein 70 (Hsp70), and chloroplastic elongation factor G (cpEF-G) were involved in pigment-related nitrogen synthesis as well as protein synthesis and processing. By integrating the proteomics data with physiological results, we revealed the metabolic patterns of nitrogen metabolism, photosynthesis, energy supply, as well as chloroplast protein synthesis, import and processing in various leaf regions at different development stages. Additionally, chloroplast-localized proteoforms involved in nitrogen metabolism, photosynthesis and protein processing implied that post-translational modifications were crucial for leaf color regulation. These results provide new clues toward understanding the mechanisms of leaf color regulation in variegated leaves.

Characterization of plutonium-containing materials and storage canisters

International Nuclear Information System (INIS)

Mason, R.E.

1997-01-01

Throughout the weapons complex, plutonium materials are stored in various containers. Some plutonium has been stored for 20 yr or more. The physical and chemical properties of the plutonium material and the containers that hold it are often not well characterized. The U.S. Department of Energy (DOE) 3013 standard sets criteria to which stored material must conform. The 3013 standard regulates materials that hold 50% or greater plutonium, and the other 50% is not specified and is usually unknown. The Materials Identification and Surveillance project is tasked to characterize representative materials and begin to characterize the other 50% and to show that materials can be brought into 3013 criteria conformance through thermal treatments

7 CFR 160.30 - Contents of containers to be designated.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Contents of containers to be designated. 160.30 Section 160.30 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) NAVAL STORES...

ASPECTS CONCERNING INTERIM FINANCIAL REPORTING IN ROMANIA: STANDARDS AND REGULATIONS

Directory of Open Access Journals (Sweden)

Aristita Rotila

2014-12-01

Full Text Available The mechanisms employed for the communication of accounting information that is necessary for users in their economic decision-making process consist of the financial statements of an entity. All legal entities, no matter the domain of their activity, have the obligation to draw up annual financial statements for every completed financial year. For certain categories of entities, reporting obligations are also required for periods other than the annual reporting, throughout the financial year. It is the case of interim financial reporting. At the level of the international accounting framework, the aspects related to interim financial reporting are the subject of a separate standard, namely, IAS 34 Interim Financial Reporting. In Romania, the current system of accounting regulations concerning the annual financial statements comprises accounting regulations that comply with the European directives and which apply to the various categories of entities, on the one hand and, on the other, accounting regulations in line with the IFRS, which are applicable to other classes of entities from certain activity sectors. The accounting regulations that apply to each category refer to, among other things, the contents and the format of financial statements that have to be presented. Analysing the system of norms and regulations, this article identifies the requirements concerning interim financial reporting in Romania, with reference to the different types of entities.

22 CFR 705.101 - Cross-reference to employee ethical conduct standards and financial disclosure regulations.

Science.gov (United States)

2010-04-01

... 22 Foreign Relations 2 2010-04-01 2010-04-01 true Cross-reference to employee ethical conduct... INVESTMENT CORPORATION ADMINISTRATIVE PROVISIONS EMPLOYEE ETHICAL CONDUCT STANDARDS AND FINANCIAL DISCLOSURE REGULATIONS § 705.101 Cross-reference to employee ethical conduct standards and financial disclosure...

Passive containment cooling system with drywell pressure regulation for boiling water reactor

Science.gov (United States)

Hill, P.R.

1994-12-27

A boiling water reactor is described having a regulating valve for placing the wetwell in flow communication with an intake duct of the passive containment cooling system. This subsystem can be adjusted to maintain the drywell pressure at (or slightly below or above) wetwell pressure after the initial reactor blowdown transient is over. This addition to the PCCS design has the benefit of eliminating or minimizing steam leakage from the drywell to the wetwell in the longer-term post-LOCA time period and also minimizes the temperature difference between drywell and wetwell. This in turn reduces the rate of long-term pressure buildup of the containment, thereby extending the time to reach the design pressure limit. 4 figures.

Radiation doses in pediatric radiology: influence of regulations and standards

International Nuclear Information System (INIS)

Suleiman, O.H.

2004-01-01

The benefits of X-ray examinations contribute to the quality of modern medicine; however the risk of using X-rays, a carcinogen, has always been a concern. This concern is heightened for pediatric patients, who have a much greater sensitivity to the carcinogenic effects of radiation than adults. The principle of as low as reasonably achievable, or ALARA, is essential for minimizing the radiation dose patients receive, especially for pediatric patients. In order to keep radiation doses ALARA, one must know the dose patients receive. The determination of radiation dose in a standard way is therefore necessary so that these doses can be compared with practice, and for meaningful comparison against voluntary standards. In extreme situations, where public health needs may require mandatory standards, or regulations, the quantitative measurement and calculation of radiation dose becomes essential. How some radiation dose metrics and standards have evolved, including the value of different metrics such as entrance air kerma, organ dose, and effective dose will be presented. Recent pediatric X-ray studies, whether or not dedicated pediatric equipment is necessary, and recent initiatives by the Food and Drug Administration for pediatric population will be discussed. (orig.)

25 CFR 542.4 - How do these regulations affect minimum internal control standards established in a Tribal-State...

Science.gov (United States)

2010-04-01

... 25 Indians 2 2010-04-01 2010-04-01 false How do these regulations affect minimum internal control... COMMISSION, DEPARTMENT OF THE INTERIOR HUMAN SERVICES MINIMUM INTERNAL CONTROL STANDARDS § 542.4 How do these regulations affect minimum internal control standards established in a Tribal-State compact? (a) If there is a...

5 CFR 1900.100 - Cross-references to employee ethical conduct standards and financial disclosure regulations.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 3 2010-01-01 2010-01-01 false Cross-references to employee ethical... ethical conduct standards and financial disclosure regulations. Officers and employees of the Appalachian Regional Commission Federal Staff are subject to the Standards of Ethical Conduct for Employees of the...

49 CFR 1019.1 - Cross-reference to employee ethical conduct standards and financial disclosure regulations.

Science.gov (United States)

2010-10-01

... 49 Transportation 8 2010-10-01 2010-10-01 false Cross-reference to employee ethical conduct... Cross-reference to employee ethical conduct standards and financial disclosure regulations. Members and employees of the Surface Transportation Board also should refer to the executive branch Standards of Ethical...

5 CFR 1300.1 - Cross-reference to employees ethical conduct standards and financial disclosure regulations.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 3 2010-01-01 2010-01-01 false Cross-reference to employees ethical conduct standards and financial disclosure regulations. 1300.1 Section 1300.1 Administrative Personnel OFFICE OF MANAGEMENT AND BUDGET ADMINISTRATIVE PROCEDURES STANDARDS OF CONDUCT § 1300.1 Cross-reference...

16 CFR 1030.101 - Cross-references to employee ethical conduct standards and financial disclosure regulations.

Science.gov (United States)

2010-01-01

... PRODUCT SAFETY COMMISSION GENERAL EMPLOYEE STANDARDS OF CONDUCT General § 1030.101 Cross-references to employee ethical conduct standards and financial disclosure regulations. Employees of the Consumer Product... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Cross-references to employee ethical conduct...

76 FR 18066 - Regulation of Fuels and Fuel Additives: Changes to Renewable Fuel Standard Program

Science.gov (United States)

2011-04-01

... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 80 Regulation of Fuels and Fuel Additives: Changes to Renewable Fuel Standard Program CFR Correction In Title 40 of the Code of Federal Regulations, Parts 72 to...-generating foreign producers and importers of renewable fuels for which RINs have been generated by the...

5 CFR 1633.1 - Cross-reference to employee ethical conduct standards and financial disclosure regulations.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 3 2010-01-01 2010-01-01 false Cross-reference to employee ethical... ethical conduct standards and financial disclosure regulations. Employees of the Federal Retirement Thrift Investment Board (Board) are subject to the executive branch-wide Standards of Ethical conduct at 5 CFR part...

30 CFR 229.123 - Standards for audit activities.

Science.gov (United States)

2010-07-01

... 229.123 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR MINERALS REVENUE... required, including a knowledge of accounting, auditing, agency regulations, and industry operations. (ii... statement of standards. (iii) The auditor's report should contain a statement of positive assurance on those...

Simulation of International Standard Problem No. 44 'KAEVER' experiments on aerosol behaviour with the CONTAIN code

International Nuclear Information System (INIS)

Kljenak, I.

2001-01-01

Experiments on aerosol behavior in a vapor-saturated atmosphere, which were performed in the KAEVER experimental facility and proposed for the OECD International Standard Problem No. 44, were simulated with the CONTAIN thermal-hydraulic computer code. The purpose of the work was to assess the capability of the CONTAIN code to model aerosol condensation and deposition in a containment of a light-water-reactor nuclear power plant at severe accident conditions. Results of dry and wet aerosol concentrations are presented and analyzed.(author)

Institutionalizing environmental protection through self-regulation: the case of environmental standards adoption in Lithuania.

Science.gov (United States)

Bileisis, Mantas; Misiune, Ieva

2017-04-01

The impacts of human activity in the environment have a global dimension, but there are no effective global governance instruments to enforce environmental standards. At the same time, many national governments lack incentives to pursue strict environmental policies. In this context, self-regulation is seen as an alternative venue to address environmental challenges. This work aims to identify factors that influence companies to engage in environmental self-regulation? For this aim in March 2015 a survey of 482 companies was conducted. The target group were companies operating in Lithuania that hold ISO14001 certificates - one of the most prolific instruments for self-regulation. The questionnaire was designed to test assumptions developed in new institutionalist literature which claim that common practices can emerge through isomorphism.- The results showed that the main motive for environmental self-regulation is the desire to improve company image, rather than protecting the environment per se. Another important finding was that the main source of pressure to adopt self-regulation was based less on the perceived demands but the customers. Rather the driver for the adoption was a feeling of a need no to fall behind industry leaders. Thus, normative isomorphism is the main mechanism through which environmental self-regulation proliferates. We claim for a rapid proliferation of environmental self-regulation perceived industry leaders need to be identified and they need to be persuaded that environmental standards are key for the development of the industry. However, this also raises questions of sustainability. Few industries have long standing leaders, and through successful investment and technological development new actors can arise and this may risk stalling or even reversing self-regulation.

7 CFR 29.3181 - Summary of standard grades.

Science.gov (United States)

2010-01-01

... Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE COMMODITY STANDARDS AND STANDARD CONTAINER... T5GF T4F T4R T4VF T4GR T5F T5R T5VF T5GR T3FR T4D T4VR T4FR T5D T5VR T5FR T4K T4GF 8 Grades of Mixed...

12 CFR 601.100 - Cross-references to employee ethical conduct standards and financial disclosure regulations.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 6 2010-01-01 2010-01-01 false Cross-references to employee ethical conduct... employee ethical conduct standards and financial disclosure regulations. Board members, officers, and other employees of the Farm Credit Administration are subject to the Standards of Ethical Conduct for Employees of...

12 CFR 336.1 - Cross-reference to employee ethical conduct standards and financial disclosure regulations.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 4 2010-01-01 2010-01-01 false Cross-reference to employee ethical conduct... and Conduct § 336.1 Cross-reference to employee ethical conduct standards and financial disclosure... Branch-wide Standards of Ethical Conduct at 5 CFR part 2635, the Corporation regulation at 5 CFR part...

10 CFR 1010.102 - Cross-references to employee ethical conduct standards, financial disclosure regulations, and...

Science.gov (United States)

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Cross-references to employee ethical conduct standards... ENERGY (GENERAL PROVISIONS) CONDUCT OF EMPLOYEES § 1010.102 Cross-references to employee ethical conduct... Standards of Ethical Conduct for Employees of the Executive Branch at 5 CFR part 2635, the DOE regulation at...

Problems of standardizing and technical regulation in the electric power industry

Science.gov (United States)

Grabchak, E. P.

2016-12-01

A mandatory condition to ensure normal operation of a power system and efficiency in the sector is standardization and legal regulation of technological activities of electric power engineering entities and consumers. Compared to the times of USSR, the present-time technical guidance documents are not mandatory to follow in most cases, being of an advisory nature due to the lack of new ones. During the last five years, the industry has been showing a deterioration of the situation in terms of ensuring reliability and engineering controllability as a result of the dominant impact of short-term market stimuli and the differences in basic technological policies. In absence of clear requirements regarding the engineering aspects of such activities, production operation does not contribute to the preserving of technical integrity of the Russian power system, which leads to the loss of performance capability and controllability and causes disturbances in the power supply to consumers. The result of this problem is a high rate of accident incidence. The dynamics of accidents by the type of equipment is given, indicating a persisting trend of growth in the number of accidents, which are of a systematic nature. Several problematic aspects of engineering activities of electric power engineering entities, requiring standardization and legal regulation are pointed out: in the domestic power system, a large number of power electrotechnical and generating equipment operate along with systems of regulation, which do not comply with the principles and technical rules representing a framework where the Energy System of Russia is built and functioning

Analysis on effects of energy efficiency regulations & standards for industrial boilers in China

Science.gov (United States)

Liu, Ren; Chen, Lili; Zhao, Yuejin; Liu, Meng

2017-11-01

The industrial boilers in China are featured by large quantity, wide distribution, high energy consumption and heavy environmental pollution, which are key problems faced by energy conservation and environmental protection in China. Meanwhile, industrial boilers are important equipment for national economy and people’s daily life, and energy conservation gets through all segments from type selection, purchase, installation and acceptance to fuel management, operation, maintenance and service. China began to implement such national mandatory standards and regulations for industrial boiler as GB24500-2009 The Minimum Allowable Values of Energy Efficiency and Energy Efficiency Grades of Industrial Boilers and TSG G002-2010 Supervision Regulation on Energy-Saving Technology for Boilers since 2009, which obviously promote the development of energy conservation of industrial boilers, but there are also some problems with the rapid development of technologies for energy conservation of industrial boilers. In this paper, the implementation of energy efficiency standards for industrial boilers in China and the significance are analyzed based on survey data, and some suggestions are proposed for the energy efficiency standards for industrial boilers. Support by Project 2015424050 of Special Fund for quality control Research in the Public Interest

5 CFR 2636.302 - Relationship to other laws and regulations.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 3 2010-01-01 2010-01-01 false Relationship to other laws and... Employees § 2636.302 Relationship to other laws and regulations. The limitations and restrictions contained... applicable standards of conduct or by reason of any statute or regulation relating to conflicts of interest...

Secondary Containers and Service Containers for Pesticides

Science.gov (United States)

Secondary containers and service containers are used by pesticide applicators in the process of applying a pesticide. EPA does not require secondary containers or service containers to be labeled or to meet particular construction standards. Learn more.

Wireless installation standard

International Nuclear Information System (INIS)

Lim, Hwang Bin

2007-12-01

This is divided six parts which are radio regulation law on securing of radio resource, use of radio resource, protection of radio resource, radio regulation enforcement ordinance with securing, distribution and assignment of radio regulation, radio regulation enforcement regulation on utility of radio resource and technical qualification examination, a wireless installation regulation of technique standard and safety facility standard, radio regulation such as certification regulation of information communicative machines and regulation of radio station on compliance of signal security, radio equipment in radio station, standard frequency station and emergency communication.

Regulations, Codes, and Standards (RCS) Template for California Hydrogen Dispensing Stations

Energy Technology Data Exchange (ETDEWEB)

Rivkin, C.; Blake, C.; Burgess, R.; Buttner, W.; Post, M.

2012-11-01

This report explains the Regulations, Codes, and Standards (RCS) requirements for hydrogen dispensing stations in the State of California. The reports shows the basic components of a hydrogen dispensing station in a simple schematic drawing; the permits and approvals that would typically be required for the construction and operation of a hydrogen dispensing station; and a basic permit that might be employed by an Authority Having Jurisdiction (AHJ).

39 CFR 3000.735-101 - Cross-reference to employee ethical conduct standards and financial disclosure regulations.

Science.gov (United States)

2010-07-01

... 39 Postal Service 1 2010-07-01 2010-07-01 false Cross-reference to employee ethical conduct... employee ethical conduct standards and financial disclosure regulations. Employees of the Postal Regulatory Commission (Commission) are subject and should refer to the executive branch-wide Standards of Ethical...

The management of electronic documents generated from compilation and revision processes of nuclear and radiation safety regulations and standards

International Nuclear Information System (INIS)

Wang Wenhai; Fan Yun; Shang Zhaorong

2010-01-01

As the Secretary Group of Regulations and Standards Review Committee on nuclear and radiation safe needs to deal with a large number of electronic documents in course of the regulation and standard review meetings, the article gives a systematical method including electronic document file naming and management as well as procedures of file transfer, storage and usage. (authors)

Mitigating Capability Analysis during LOCA for Korean Standard Nuclear Power Plants in Containment Integrity

Energy Technology Data Exchange (ETDEWEB)

Choi, Young; Park, Soo Yong; Kim, D. H.; Song, Y. M. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2007-07-01

The objective of this paper is to establish Containment spray operational technical bases for the typical Korean Standard Nuclear Power plants (Ulchin units 3 and 4) by modeling the plant, and analyzing a loss of coolant accident (LOCA) using the MAAP code. The severe accident phenomena at nuclear power plants have large uncertainties. For the integrity of the reactor vessel and containment safety against severe accidents, it is essential to understand severe accident sequences and to assess the accident progression accurately by computer codes. Furthermore, it is important to attain the capability to analyze a advanced nuclear reactor design for a severe accident prevention and mitigation.

7 CFR 57.950 - Labeling of containers of eggs for importation.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Labeling of containers of eggs for importation. 57.950... AND STANDARDS UNDER THE AGRICULTURAL MARKETING ACT OF 1946 AND THE EGG PRODUCTS INSPECTION ACT (CONTINUED) INSPECTION OF EGGS (EGG PRODUCTS INSPECTION ACT) Regulations Governing the Inspection of Eggs...

[Preparation of the database and the Internet (WWW) homepage for regulations on chemicals in Japan].

Science.gov (United States)

Yamamoto, M; Morita, M; Kaminuma, T

1999-01-01

We prepared a database on chemical regulations in Japan. The regulations consist of "The Law concerning the Examination and Regulation of Manufacture, etc., of Chemical Substances", "Poisonous and Deleterious Substances", Control Law", "Waterworks Law", "Law for the Control of Household Products containing Harmful Substances", and Pesticide Residues in Food Sanitation Law". We also set up a World Wide Web (WWW) homepage containing an explanation of the law as well as chemical names, CAS registry numbers, and standards. The WWW pages contain lists of chemicals and the retrieval page for the database.

Legal status of minister's notices and technology standards of 'Korea institute of nuclear safety'(KINS) to regulate nuclear safety

International Nuclear Information System (INIS)

Jung, S. K.; Jung, M. M.; Kim, S. W.; Jang, K. H.; Oh, B. J.

2003-01-01

Concerning nuclear safety or technology standards, each of 'notices' issued by minister of science and technology(MOST) empowered by law of its regulation is obviously forceful as a law, if not all. But the standards made by the chief of Korea institute of nuclear safety(KINS) to meet the tasks entrusted to KINS by MOST is only conditionally forceful as a law, that is, on the condition that law or regulation empowered the chief of KINS to make nuclear safety and/or technology standards

HARMONIZATION OF NATIONAL REGULATION AND INTERNATIONAL FINANCIAL REPORTING STANDARDS – PARTICULAR CASE OF NONCURRENT ASSETS

Directory of Open Access Journals (Sweden)

Coste Andreea Ioana

2013-07-01

Full Text Available In the scientific literature, accounting harmonization is a top topic because it helps to increase the comparability of financial statements. Also in Romania in the last 10 years becames a topic that is very often debated. The harmonization is trying to reduce differences of financial reporting statements between countries or, in the other words, it is trying to bring to a common denominator of existing rules when appear conflicts of comparability between them. The purpose of this paper is to measure the harmonisation between national and international regulation for a significant element of financial position statement, such as noncurrent assets. This paper provides an empirical research of information that must be presented by entities which apply national accounting standards or international ones when financial statements are prepared, trying to measure the harmonization between the two referential. Thus, in trying to determine the harmonisation, we use the Jaccard coefficient in order to provide an overview of the degree of harmonization of accounting practice. When measuring the degree of comparability of Romanian accounting regulations with International Accounting Standards we analyzed noncurrent assets and impairment of assets using the Jaccard coefficient for accounting treatments and we calculated an average of similarities between the two regulations. Further, the results suggest that there is an average level of harmonization for the accounting treatment of noncurrent assets and for determining the impairment of the assets, the methods are the same. The study contributes to the development of accounting literature about the harmonisation between national regulation and international standards regarding the noncurrent assets and impairment of the assets, which together with the other elements define the activity of the business. In addition, the study provides an analysis of how the regulations treats noncurrent assets, during the

IEEE Std 317-1972: IEEE standard for electric penetration assemblies in containment structures for nuclear power generating stations

International Nuclear Information System (INIS)

Anon.

1992-01-01

This standard prescribes the mechanical, electrical, and test requirements for the design, construction, and installation of electric penetration assemblies in containment structures for stationary nuclear power generating stations. The electric conductor and insulation characteristics of external circuits which connect to penetration assemblies are beyond the scope of these criteria. If there should be any conflict between this standard and those documents referenced herein, this standard shall take precedence over the referenced documents

77 FR 1319 - Regulation of Fuels and Fuel Additives: 2012 Renewable Fuel Standards

Science.gov (United States)

2012-01-09

... fuels such as ethanol and biodiesel. Potentially regulated categories include: NAICS \\1\\ Examples of... they are produced as well as the cost associated with transporting these fuels to the U.S. Of the... II.E, we believe that the 1.0 billion gallon standard can indeed be met. Since biodiesel has an...

Present status of nuclear containments in Korea

International Nuclear Information System (INIS)

Park, Jihong; Hong, Jaekeun; Lee, Byunghoon; Son, Youngho

2007-01-01

Since the first nuclear power plant in Korea, Kori unit no.1, was started in commercial service in 1978, 20 units including Kori unit no.1 have been operated and maintained until now in Korea. Recently several units were started to be constructed and also, additionally more than 4 units were planned to be constructed in the near future. The importance of nuclear containments has been always one of the hottest issues for the safety and protection of nuclear power plants until now. At the beginning of nuclear power plants construction in Korea, several typed nuclear containment systems were adopted. For those reasons, various codes, standards, and inspection technologies are applied to nuclear containment systems differently. In this study, the status of inservice inspection performed for the safety and maintenance of nuclear containments in Korea was researched. Overall nuclear containment systems and inspections performed up to recently in Korea including trends, inspection items, periods, and regulations were described briefly. (author)

Electronic Commerce: a battle on regulation, standards transportation media and business integration

Directory of Open Access Journals (Sweden)

Kim Andersen

1998-11-01

Full Text Available The drive towards the electronic commerce organisation is both a troublesome and a strifted path for government, enterprises and consumers worldwide. In this article we analyse the evolution of electronic commerce in Denmark during the period 1995-1998 from four perspectives: regulation, standards, transportation media and business integration. The Danish government is stimulating the use of electronic commerce using direct and indirect policy initiatives on central, governmental regulation and establishment of greens enabling self-regulation. Also, the governments own, organisational management is in Denmark seen as a mean to exalt electronic commerce. Onwards, the fist on proprietary standards and the UN/EDIFACT is an ongoing source of delaying, stimulating or reventing electronic commerce depending on the business sector and the size of market actor addressed. In Denmark, the direct access and value added network supporters have so far been the dominating mean to transport the electronic documents in the business transaction. The Internet and XML technology is at the turn of the century challenging the way of doing business within this field. Some view this as the big blue to speed the diffusion of electronic commerce; others are worried that the incentive to investment and pull the partners in the value chain to use EDI might be lost. Finally, our study conclude that the debate on business integration issues is ambiguous and characterised by substantial uncertainty on for example the role of intermediates, direct sale, hyper-shift in business partners and the pull/push of global enterprises at the local markets.

Current and proposed revisions, changes, and modifications to American codes and standards to address packaging, handling, and transportation of radioactive materials and how they relate to comparable international regulations

International Nuclear Information System (INIS)

Borter, W.H.; Froehlich, C.H.

2004-01-01

This paper addresses current and proposed revisions, additions, and modifications to American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code (BPVC) (i.e., ''ASMEthe Code'') Section III, Division 3 and American National Standards Institute (ANSI)/ASME N14.6. It provides insight into the ongoing processes of the associated committees and highlights important revisions, changes, and modifications to this Code and Standard. The ASME Code has developed and issued Division 3 to address items associated with the transportation and storage of radioactive materials. It currently only addresses ''General Requirements'' in Subsections WA and ''Class TP (Type B) Containments'' (Transportation Packages) in Subsection WB, but is in the process of adding a new Subsection WC to address ''Class SC'' (Storage Containments). ANSI/ASME Standard N14.6 which interacts with components constructed to Division 3 by addressinges special lifting devices for radioactive material shipping containers. This Standard is in the process of a complete re-write. This Code and Standard can be classified as ''dynamic'' in that their committees meet at least four times a year to evaluate proposed modifications and additions that reflect current safety practices in the nuclear industry. These evaluations include the possible addition of new materials, fabrication processes, examination methods, and testing requirements. An overview of this ongoing process is presented in this paper along with highlights of the more important proposed revisions, changes, and modifications and how they relate to United States (US) and international regulations and guidance like International Atomic Energy Agency (IAEA) Requirement No. TS-R-1

The Food Industry and Self-Regulation: Standards to Promote Success and to Avoid Public Health Failures

Science.gov (United States)

Sharma, Lisa L.; Teret, Stephen P.

2010-01-01

Threatened by possible government regulation and critical public opinion, industries often undertake self-regulatory actions, issue statements of concern for public welfare, and assert that self-regulation is sufficient to protect the public. The food industry has made highly visible pledges to curtail children's food marketing, sell fewer unhealthy products in schools, and label foods in responsible ways. Ceding regulation to industry carries opportunities but is highly risky. In some industries (e.g., tobacco), self-regulation has been an abject failure, but in others (e.g., forestry and marine fisheries), it has been more successful. We examined food industry self-regulation in the context of other self-regulatory successes and failures and defined 8 standards that should be met if self-regulation is to be effective. PMID:20019306

75 FR 49363 - Deposit Insurance Regulations; Permanent Increase in Standard Coverage Amount; Advertisement of...

Science.gov (United States)

2010-08-13

... Insurance Regulations; Permanent Increase in Standard Coverage Amount; Advertisement of Membership... Procedure Act The FDIC believes that good cause exists for issuing the final rule without providing an... the public interest.'' \\8\\ The FDIC also finds good cause for issuing the final rule without a 30-day...

Incorporation of standard terms according to the CISG and the CESL: Will these Competing Instruments Enhance Legal Certainty in Cross-Border Sales Transactions?

NARCIS (Netherlands)

Kruisinga, S.A.

2013-01-01

This article compares the regulation of standard terms in the UN Convention on Contracts for the International Sale of Goods (CISG) and the Draft Regulation on a Common European Sales Law (CESL). Even though the CISG does not contain any express provisions concerning standard terms, this issue is

7 CFR 946.18 - Container.

Science.gov (United States)

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Container. 946.18 Section 946.18 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Order Regulating Handling Definitions § 946.18 Container. Container means a sack, box, bag, crate...

7 CFR 917.12 - Container.

Science.gov (United States)

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Container. 917.12 Section 917.12 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... CALIFORNIA Order Regulating Handling Definitions § 917.12 Container. Container means a box, bag, crate, lug...

7 CFR 922.17 - Container.

Science.gov (United States)

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Container. 922.17 Section 922.17 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... IN WASHINGTON Order Regulating Handling Definitions § 922.17 Container. Container means a box, bag...

7 CFR 959.13 - Container.

Science.gov (United States)

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Container. 959.13 Section 959.13 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Regulating Handling Definitions § 959.13 Container. Container means a box, bag, crate, hamper, basket...

7 CFR 948.14 - Container.

Science.gov (United States)

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Container. 948.14 Section 948.14 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Order Regulating Handling Definitions § 948.14 Container. Container means a sack, bag, crate, box...

7 CFR 966.13 - Container.

Science.gov (United States)

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Container. 966.13 Section 966.13 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Regulating Handling Definitions § 966.13 Container. Container means a box, bag, crate, hamper, basket...

7 CFR 906.12 - Container.

Science.gov (United States)

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Container. 906.12 Section 906.12 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... RIO GRANDE VALLEY IN TEXAS Order Regulating Handling Definitions § 906.12 Container. Container means...

7 CFR 916.14 - Container.

Science.gov (United States)

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Container. 916.14 Section 916.14 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Regulating Handling Definitions § 916.14 Container. Container means a box, bag, crate, lug, basket, carton...

7 CFR 923.17 - Container.

Science.gov (United States)

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Container. 923.17 Section 923.17 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... COUNTIES IN WASHINGTON Order Regulating Handling Definitions § 923.17 Container. Container means a box, bag...

The amended regulations for the safe transport of radioactive materials in Japan

International Nuclear Information System (INIS)

Takemura, Yoshio

1978-01-01

To cope with the inadequacies of the laws and regulations including the Law Concerning Prevention of Radiation Injuries Due to Radioisotopes, Etc., the Amended Regulations for the Safe Transport of Radioactive Materials in Japan has been issued. It is based on the Regulations of IAEA for the Safe Transport of Radioactive Materials and the Technical Standards for the Transport of Radioactive Materials decided by the AEC of Japan. In the amended regulations, emphasis is placed on the safety design of transporting goods. They are classified in Types L, A and B according to shock resistance and fire resistance, and the quantities of radioisotopes allowed to be contained in respective types are specified. The following matters are described: basic ideas concerning the types of transporting goods, test standards for the goods, transport standards for the goods, and nondestructive test apparatuses in transport. (Mori, K.)

Hard Work in Soft Regulation: A Discussion of the Social Mechanisms in OHS Management Standards and Possible Dilemmas in the Regulation of Psychosocial Work Environment

Directory of Open Access Journals (Sweden)

Pernille Hohnen

2014-09-01

Full Text Available Certified occupational health and safety (OHS management systems have become a global instrument in regulation of the work environment. However, their actual impact on OHS—in particular on softer psychosocial issues in the work environment—has been questioned. The most important standard of OHS management is OHSAS 18001, which has recently been supplemented with a British publically available guideline (PAS 1010 focusing specifically on psychosocial risk management. On the basis of the international literature on management standards, the present paper analyses OHSAS 18001 and PAS 1010 in order to understand the mechanism by which they work. The paper takes a social constructionist approach conceptualizing standards and their expected mechanisms as socially constructed—based on a particular kind of knowledge and logic—although they are presented as objective. Such a constructionist approach also emphasizes how standards transform specific work environment problems into generic procedures that can be audited. In the case of OHS standards, both the work environment in general and the psychosocial risks in particular are transformed into simple monocausal auditable relations whereby the complexity of psychosocial work environment issues seems to disappear. The new PAS 1010 guideline, which is particularly focusing on regulation of the psychosocial work environment, only partly succeeds in solving these shortcomings of OHSAS 18001.

Secondary Containment Design for the LLNL B801 Diala Oil Tank

Energy Technology Data Exchange (ETDEWEB)

Mertesdorf, E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2016-12-14

Design is to add an extension to the secondary containment of tank T1-A3 at building 801. Piping from the inner tank penetrates the secondary containment tank below the liquid level of the primary tank. To meet Oil Pollution Prevention Regulation 40 CFR 120.7 the single wall piping needs to be provided with secondary containment. Steel Tank Institute (STI) conference publication states: §112.3(d)(1)(iii) –SPCC Plan requirements- Systems shall be designed in accordance with good engineering practice, including consideration of applicable industry standards and that procedures for required inspections and testing have been established. Section 112.7(a)(2) allows for deviations from specific rule requirements, provided the Owner/operator responsible to select, document and implement alternate measure and a PE certifies the SPCC Plan in accordance with good engineering practices, including consideration of industry standards

The DT-19 container design, impact testing and analysis

International Nuclear Information System (INIS)

Aramayo, G.A.; Goins, M.L.

1995-01-01

Containers used by the Department of Energy (DOE) for the transport of radioactive material components, including components and special assemblies, are required to meet certain impact and thermal requirements that are demonstrated by performance or compliance testing, analytical procedures or a combination of both. The Code of Federal Regulations (CFR) Part 49, Section 173.7(d) stipulates that, 'Packages (containers) made by or under direction of the US DOE may be used for the transportation of radioactive materials when evaluated, approved, and certified by the DOE against packaging standards equivalent to those specified in 10 CFR Part 71. This paper describes the details of the design, analysis and testing efforts undertaken to improve the overall structural and thermal integrity of the DC-19 shipping container

49 CFR 173.189 - Batteries containing sodium or cells containing sodium.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Batteries containing sodium or cells containing sodium. 173.189 Section 173.189 Transportation Other Regulations Relating to Transportation PIPELINE AND... Than Class 1 and Class 7 § 173.189 Batteries containing sodium or cells containing sodium. (a...

76 FR 48863 - Federal Travel Regulation (FTR); Relocation Allowances-Standard Mileage Rate for Moving Purposes

Science.gov (United States)

2011-08-09

... Travel Regulation (FTR); Relocation Allowances--Standard Mileage Rate for Moving Purposes AGENCY: Office... agencies will reimburse an employee for using a privately owned vehicle for relocation on a worldwide basis...), Office of Travel, Transportation and Asset Management (MT), General Services Administration at (202) 208...

International regulations in capital standards in insurance companies and banking system of Serbia

Directory of Open Access Journals (Sweden)

Milić Dragana

2014-01-01

Full Text Available The emergence and expansion of the recent financial crisis has renewed the question of regulation and supervision of the financial system. Therefore, the question of managing financial risks is becoming increasingly popular and gaining more and more importance. Regulators have in recent years introduced capital standards based on specific sensitivity to risk. Based on defined issues, the starting point is the general hypothesis that the capital adequacy is a key base for measuring the resistance of the banking and insurance sector to market shocks. This paper will present the analytical, synthetic and general scientific methods. The comparative method is used in this paper to highlight the similarities and differences between Solvency II and Basel III and their operational efficiency.

The development of ISO freight containers as IP-2 packagings

International Nuclear Information System (INIS)

Janicki, M.C.; Vaughan, R.A.

1993-01-01

Design specifications were developed for ISO freight containers to meet the requirements of the transport regulations in the 1985 Edition of IAEA SS6, and to maximize the technical and commercial benefits offered to consignors by this type of container for the transport and handling of bulk LSA/SCO materials. A range of IP-2 ISO freight containers have been designed and built to these specifications and are in use in the UK. This paper discusses the regulatory considerations which had to be reviewed and interpreted in developing freight containers as Industrial Package Type 2 (IP-2) packagings and the development of performance standards to meet the regulatory requirements. Outline details of the packages developed are indicated together with examples of handling equipment developed to facilitate loading and unloading. (J.P.N.)

Co-operative development of nuclear safety regulations, guides and standards based on NUSS

International Nuclear Information System (INIS)

Pachner, J.; Boyd, F.C.; Yaremy, E.M.

1985-01-01

A major need of developing Member States building nuclear power plants (NPPs) of foreign origin is to acquire a capability to regulate such nuclear plants independently. Among other things, this requires the development of national nuclear safety regulations, guides and standards to govern the development and use of nuclear technology. Recognizing the importance and complexity of this task, it seems appropriate that the NPP-exporting Member States share their experience and assist the NPP-importing Member States in the development of their national regulations and guides. In 1983, the Atomic Energy Control Board and Atomic Energy of Canada Ltd. conducted a study of a possible joint programme involving Canada, an NPP-importing Member State and the IAEA for the development of the national nuclear safety regulations and guides based on NUSS documents. During the study, a work plan with manpower estimates for the development of design regulations, safety guides and a guide for regulatory evaluation of design was prepared as an investigatory exercise. The work plan suggests that a successful NUSS implementation in developing Member States will require availability of significant resources at the start of the programme. The study showed that such a joint programme could provide an effective mechanism for transfer of nuclear safety know-how to the developing Member States through NUSS implementation. (author)

Forkhead-associated (FHA) Domain Containing ABC Transporter Rv1747 Is Positively Regulated by Ser/Thr Phosphorylation in Mycobacterium tuberculosis*

Science.gov (United States)

Spivey, Vicky L.; Molle, Virginie; Whalan, Rachael H.; Rodgers, Angela; Leiba, Jade; Stach, Lasse; Walker, K. Barry; Smerdon, Stephen J.; Buxton, Roger S.

2011-01-01

One major signaling method employed by Mycobacterium tuberculosis, the causative agent of tuberculosis, is through reversible phosphorylation of proteins mediated by protein kinases and phosphatases. This study concerns one of these enzymes, the serine/threonine protein kinase PknF, that is encoded in an operon with Rv1747, an ABC transporter that is necessary for growth of M. tuberculosis in vivo and contains two forkhead-associated (FHA) domains. FHA domains are phosphopeptide recognition motifs that specifically recognize phosphothreonine-containing epitopes. Experiments to determine how PknF regulates the function of Rv1747 demonstrated that phosphorylation occurs on two specific threonine residues, Thr-150 and Thr-208. To determine the in vivo consequences of phosphorylation, infection experiments were performed in bone marrow-derived macrophages and in mice using threonine-to-alanine mutants of Rv1747 that prevent specific phosphorylation and revealed that phosphorylation positively modulates Rv1747 function in vivo. The role of the FHA domains in this regulation was further demonstrated by isothermal titration calorimetry, using peptides containing both phosphothreonine residues. FHA-1 domain mutation resulted in attenuation in macrophages highlighting the critical role of this domain in Rv1747 function. A mutant deleted for pknF did not, however, have a growth phenotype in an infection, suggesting that other kinases can fulfill its role when it is absent. This study provides the first information on the molecular mechanism(s) regulating Rv1747 through PknF-dependent phosphorylation but also indicates that phosphorylation activates Rv1747, which may have important consequences in regulating growth of M. tuberculosis. PMID:21622570

Employee Retirement Income Security Act of 1974: rules and regulations for administration and enforcement; claims procedure. Pension and Welfare Benefits Administration, Labor. Final regulation.

Science.gov (United States)

2000-11-21

This document contains a final regulation revising the minimum requirements for benefit claims procedures of employee benefit plans covered by Title I of the Employee Retirement Income Security Act of 1974 (ERISA or the Act). The regulation establishes new standards for the processing of claims under group health plans and plans providing disability benefits and further clarifies existing standards for all other employee benefit plans. The new standards are intended to ensure more timely benefit determinations, to improve access to information on which a benefit determination is made, and to assure that participants and beneficiaries will be afforded a full and fair review of denied claims. When effective, the regulation will affect participants and beneficiaries of employee benefit plans, employers who sponsor employee benefit plans, plan fiduciaries, and others who assist in the provision of plan benefits, such as third-party benefits administrators and health service providers or health maintenance organizations that provide benefits to participants and beneficiaries of employee benefit plans.

Environmental Monitoring, Water Quality - MO 2009 Water Quality Standards - Table G Lake Classifications and Use Designations (SHP)

Data.gov (United States)

NSGIC State | GIS Inventory — This data set contains Missouri Water Quality Standards (WQS) lake classifications and use designations described in the Missouri Code of State Regulations (CSR), 10...

7 CFR 205.307 - Labeling of nonretail containers used for only shipping or storage of raw or processed...

Science.gov (United States)

2010-01-01

... Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) ORGANIC FOODS PRODUCTION ACT... of destination or the container labeling specifications of a foreign contract buyer: Provided, That...

Worldwide Regulations of Standard Values of Pesticides for Human Health Risk Control: A Review

Science.gov (United States)

Jennings, Aaron

2017-01-01

The impact of pesticide residues on human health is a worldwide problem, as human exposure to pesticides can occur through ingestion, inhalation, and dermal contact. Regulatory jurisdictions have promulgated the standard values for pesticides in residential soil, air, drinking water, and agricultural commodity for years. Until now, more than 19,400 pesticide soil regulatory guidance values (RGVs) and 5400 pesticide drinking water maximum concentration levels (MCLs) have been regulated by 54 and 102 nations, respectively. Over 90 nations have provided pesticide agricultural commodity maximum residue limits (MRLs) for at least one of the 12 most commonly consumed agricultural foods. A total of 22 pesticides have been regulated with more than 100 soil RGVs, and 25 pesticides have more than 100 drinking water MCLs. This research indicates that those RGVs and MCLs for an individual pesticide could vary over seven (DDT drinking water MCLs), eight (Lindane soil RGVs), or even nine (Dieldrin soil RGVs) orders of magnitude. Human health risk uncertainty bounds and the implied total exposure mass burden model were applied to analyze the most commonly regulated and used pesticides for human health risk control. For the top 27 commonly regulated pesticides in soil, there are at least 300 RGVs (8% of the total) that are above all of the computed upper bounds for human health risk uncertainty. For the top 29 most-commonly regulated pesticides in drinking water, at least 172 drinking water MCLs (5% of the total) exceed the computed upper bounds for human health risk uncertainty; while for the 14 most widely used pesticides, there are at least 310 computed implied dose limits (28.0% of the total) that are above the acceptable daily intake values. The results show that some worldwide standard values were not derived conservatively enough to avoid human health risk by the pesticides, and that some values were not computed comprehensively by considering all major human exposure

Worldwide Regulations of Standard Values of Pesticides for Human Health Risk Control: A Review.

Science.gov (United States)

Li, Zijian; Jennings, Aaron

2017-07-22

Abstract : The impact of pesticide residues on human health is a worldwide problem, as human exposure to pesticides can occur through ingestion, inhalation, and dermal contact. Regulatory jurisdictions have promulgated the standard values for pesticides in residential soil, air, drinking water, and agricultural commodity for years. Until now, more than 19,400 pesticide soil regulatory guidance values (RGVs) and 5400 pesticide drinking water maximum concentration levels (MCLs) have been regulated by 54 and 102 nations, respectively. Over 90 nations have provided pesticide agricultural commodity maximum residue limits (MRLs) for at least one of the 12 most commonly consumed agricultural foods. A total of 22 pesticides have been regulated with more than 100 soil RGVs, and 25 pesticides have more than 100 drinking water MCLs. This research indicates that those RGVs and MCLs for an individual pesticide could vary over seven (DDT drinking water MCLs), eight (Lindane soil RGVs), or even nine (Dieldrin soil RGVs) orders of magnitude. Human health risk uncertainty bounds and the implied total exposure mass burden model were applied to analyze the most commonly regulated and used pesticides for human health risk control. For the top 27 commonly regulated pesticides in soil, there are at least 300 RGVs (8% of the total) that are above all of the computed upper bounds for human health risk uncertainty. For the top 29 most-commonly regulated pesticides in drinking water, at least 172 drinking water MCLs (5% of the total) exceed the computed upper bounds for human health risk uncertainty; while for the 14 most widely used pesticides, there are at least 310 computed implied dose limits (28.0% of the total) that are above the acceptable daily intake values. The results show that some worldwide standard values were not derived conservatively enough to avoid human health risk by the pesticides, and that some values were not computed comprehensively by considering all major human

Draft of regulations for road transport of radioactive wastes

International Nuclear Information System (INIS)

Gese, J.; Zizka, B.

1979-06-01

A draft regulation is presented for the transport of solid and solidified radioactive wastes from nuclear power plants. The draft takes into consideration dosimetric, safety and fire-fighting directives, transport organization, anticipated amounts of radioactive wastes, characteristics of containers, maintenance of vehicles, and equipment of vehicles and personnel. The draft is based on the provisional regulations governing the transport on public roads issued in 1973, valid directives, decrees, acts and standards, and complies with 1973 IAEA requirements. (J.P.)

Co-regulation in EU personal data protection : The case of technical standards and the privacy by design standardisation ‘mandate’

NARCIS (Netherlands)

Kamara, Irene

The recently adopted General Data Protection Regulation (GDPR), a technology-neutral law, endorses self-regulatory instruments, such as certification and technical standards. Even before the adoption of the General Data Protection Regulation, standardisation activity in the field of privacy

12 CFR 400.101 - Cross-reference to employee financial disclosure and ethical conduct standards regulations.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 4 2010-01-01 2010-01-01 false Cross-reference to employee financial disclosure and ethical conduct standards regulations. 400.101 Section 400.101 Banks and Banking EXPORT-IMPORT.... Employees of the Export-Import Bank of the United States (Bank) should refer to: (a) The executive branch...

Review and comparison of quality standards, guidelines and regulations for laboratories

Directory of Open Access Journals (Sweden)

Tjeerd A.M. Datema

2011-12-01

Full Text Available Background: The variety and number of laboratory quality standards, guidelines and regulations (hereafter: quality documents makes it difficult to choose the most suitable one for establishing and maintaining a laboratory quality management system. Objectives: There is a need to compare the characteristics, suitability and applicability of quality documents in view of the increasing efforts to introduce quality management in laboratories, especially in clinical diagnostic laboratories in low income and middle income countries. This may provide valuable insights for policy makers developing national laboratory policies, and for laboratory managers and quality officers in choosing the most appropriate quality document for upgrading their laboratories. Method: We reviewed the history of quality document development and then selected a subset based on their current use. We analysed these documents following a framework for comparison of quality documents that was adapted from the Clinical Laboratory Standards Institute guideline GP26 Quality management system model for clinical laboratory services. Results: Differences were identified between national and international, and non-clinical and clinical quality documents. The most salient findings were the absence of provisions on occurrence management and customer service in almost all non-clinical quality documents, a low number of safety requirements aimed at protecting laboratory personnel in international quality documents and no requirements regarding ethical behaviour in almost all quality documents. Conclusion: Each laboratory needs to investigate whether national regulatory standards are present. These are preferred as they most closely suit the needs of laboratories in the country. A laboratory should always use both a standard and a guideline: a standard sums up the requirements to a quality management system, a guideline describes how quality management can be integrated in the laboratory

Radiation safety standards and regulations

International Nuclear Information System (INIS)

Ermolina, E.P.; Ivanov, S.I.

1993-01-01

Radiation protection laws of Russia concerning medical application of ionizing radiation are considered. Main concepts of the documents and recommendations are presented. Attention was paid to the ALARA principle, safety standrds for paietients, personnel and population, radiation protection. Specific feature of the standardization of radiation factors is the establishment of two classes of norms: main dose limits and permissible levels. Maximum dose commitment is the main standard. Three groups of critical organs and three categories of the persons exposed to radiation are stated. Main requirements for radiation protection are shown

Proposals for the Radioactive Substances (Basic Safety Standards) (England and Wales) Regulations 2000 and the Radioactive Substances (Basic Safety Standards) (England and Wales) Direction 2000. Consultative document

International Nuclear Information System (INIS)

2000-01-01

This document contains proposals for changes to the Radioactive Substances Act 1993 (RSA 93) and proposals for a Direction to be given to the Environment Agency in order to implement aspects of the European Directive 96/29/Euratom concerned with the control of radioactive waste. The Directive lays down basic safety standards for the protection of the health of workers and the general public against the dangers arising from ionising radiation. With the Government pledged to making government more accessible and responsive, an important feature of this approach is effective consultation with all interested organisations. This leads to more realistic and robust proposals, which is particularly important when dealing with proposed legislation. In March this year, the Government published a consultation paper 'The Radioactive Substances Act 1993: Implementing the Revised Basic Safety Standards Directive Euratom 96/29.' This sought comments on the basic principles for change - including the setting of levels of radioactivity below which radioactive material should be considered outside the framework of regulatory control. This document forms the second stage of the consultation process with the aim of gathering views on the proposed legal instruments to implement the Directive. This document: explains the background to the proposed regulations (paragraphs 8-13); summarises the results of the consultation on principles (paragraphs 14-24); describes the proposed changes (paragraphs 25-36); includes draft Regulations (paragraphs 27-29); includes a draft Direction to the Environment Agency (paragraphs 30-36); describes the next steps (paragraphs 37-39); includes a draft Regulatory Impact Assessment (paragraphs 40-41). In general, the devolved administrations in Scotland, Wales and Northern Ireland have assumed responsibility for environmental issues and hence management of radioactive waste policies and legislation affecting their respective countries. However, this

CD3 gamma contains a phosphoserine-dependent di-leucine motif involved in down-regulation of the T cell receptor

DEFF Research Database (Denmark)

Dietrich, J; Hou, X; Wegener, A M

1994-01-01

-regulation of the TCR. Furthermore, analysis of a series of CD3 gamma truncation mutants indicated that in addition to S126 phosphorylation a motif C-terminal of S126 was required for TCR down-regulation. Point mutation analyses confirmed this observation and demonstrated that a membrane-proximal di-leucine motif (L131......, indicating that the TCR was down-regulated by endocytosis via clathrin coated pits. Based on the present results and previously published observations on intracellular receptor sorting, a general model for intracellular sorting of receptors containing di-leucine- or tyrosine-based motifs is proposed....

78 FR 27913 - Revision of Crane Regulation Standards for Mobile Offshore Drilling Units (MODUs), Offshore...

Science.gov (United States)

2013-05-13

...)(1) by updating the reference for API nameplate data to reflect its location in the latest edition of.... Civil Justice Reform I. Protection of Children J. Indian Tribal Governments K. Energy Effects L... existing regulations by adopting the most recent editions of API Spec. 2C and RP 2D standards. By updating...

Regulation of naturally occurring radioactive materials (NORM) with emphasis on NORM disposal options

International Nuclear Information System (INIS)

Gray, P.

1995-01-01

Regulation of radioactive material can occur at the Federal, State, and sometimes local level. In addition to regulations at the federal and state level, there are guidelines and standards that do not carry the weight of law, yet are often referenced. Neither the Nuclear Regulatory Commission (NRC) or Environmental Protection Agency (EPA) categorically regulates NORM at this time. However, many of the existing regulations and guidelines for licensed radioactive material can be applied by states and other regulatory agencies to NORM. The primary regulations covering radioactive materials and exposures were promulgated under the Atomic Energy Act (AEA) or 1954, as amended. NRC licenses and regulates civilian use of nuclear materials to protect public health and safety and the environment. NRC makes rules and sets standards for licensees and inspects the activities of licensees to insure that they do not violate safety rules. OSHA regulations for worker protection from exposures to radioactivity are contained in 29CFR1910.96. These standards are designed to protect workers from exposure to radiation in programs other than those regulated by OSHA. The Uranium Mill Tailings Control Act, with implementing regulations found in 40CFR192 were promulgated by the EPA for cleanup of uranium mill tailings. These standards are often used by states and other agencies in regulating cleanup of NORM. EPA is currently considering regulation of NORM on NRC and DOE facilities under 40CFR195

Drop analysis for structural integrity evaluation of KJRR fuel transport container

International Nuclear Information System (INIS)

Yang, Yun Young; Lim, Jong Min; Choi, Woo Seok; Lee, Ju Chan

2016-01-01

A fuel transport container for KiJang Research Reactor(KJRR) has been developed to transport fresh fuel assemblies and fission molly targets which are used for a research reactor built in Kijang. The KJRR fuel transport container is a type-A(F) container, which is defined in domestic and foreign regulations of a radioactive substance container. According to Nuclear Safety and Security Commission's notification, the container should meet the accident conditions defined in IAEA safety Standard Series, US NRC and etc. In this study, a structural integrity of the KJRR fuel transport container is evaluated by conducting computational analyses of 9-meter free drop and 1 meter puncture. It is confirmed that structural integrity of the KJRR fuel transport container can be maintained in the transportation accident condition. Hereafter, when the test model is produced, a safety test will be conducted and its result will be compared with the result of drop and puncture analyses.

Evaluation of alternatives for high-level and transuranic radioactive- waste disposal standards

International Nuclear Information System (INIS)

Klett, R.D.; Gruebel, M.M.

1992-12-01

The remand of the US Environmental Protection Agency's long-term performance standards for radioactive-waste disposal provides an opportunity to suggest modifications that would make the regulation more defensible and remove inconsistencies yet retain the basic structure of the original rule. Proposed modifications are in three specific areas: release and dose limits, probabilistic containment requirements, and transuranic-waste disposal criteria. Examination of the modifications includes discussion of the alternatives, demonstration of methods of development and implementation, comparison of the characteristics, attributes, and deficiencies of possible options within each area, and analysis of the implications for performance assessments. An additional consideration is the impact on the entire regulation when developing or modifying the individual components of the radiological standards

Nutrient supply to organic agriculture as governed by EU regulations and standards in six European countries

DEFF Research Database (Denmark)

Løes, Anne Kristin; Bünemann, E.K.; Cooper, J.

2017-01-01

-farm P sources include conventional animal manure, composted or anaerobically digested organic residues, rock phosphate, and some animal residues such as meat and bone meal. The recent proposed revision of EU regulations for organic production (2014) puts less emphasis on closing nutrient cycles...... as means are taken to ensure the quality and safety of these inputs. Awareness of the need to close nutrient cycles may contribute to adapting regulations and private standards to support recycling of nutrients from society to organic agriculture. A better definition of the term “natural substance...

Choline Catabolism in Burkholderia thailandensis Is Regulated by Multiple Glutamine Amidotransferase 1-Containing AraC Family Transcriptional Regulators.

Science.gov (United States)

Nock, Adam M; Wargo, Matthew J

2016-09-15

Burkholderia thailandensis is a soil-dwelling bacterium that shares many metabolic pathways with the ecologically similar, but evolutionarily distant, Pseudomonas aeruginosa Among the diverse nutrients it can utilize is choline, metabolizable to the osmoprotectant glycine betaine and subsequently catabolized as a source of carbon and nitrogen, similar to P. aeruginosa Orthologs of genes in the choline catabolic pathway in these two bacteria showed distinct differences in gene arrangement as well as an additional orthologous transcriptional regulator in B. thailandensis In this study, we showed that multiple glutamine amidotransferase 1 (GATase 1)-containing AraC family transcription regulators (GATRs) are involved in regulation of the B. thailandensis choline catabolic pathway (gbdR1, gbdR2, and souR). Using genetic analyses and sequencing the transcriptome in the presence and absence of choline, we identified the likely regulons of gbdR1 (BTH_II1869) and gbdR2 (BTH_II0968). We also identified a functional ortholog for P. aeruginosa souR, a GATR that regulates the metabolism of sarcosine to glycine. GbdR1 is absolutely required for expression of the choline catabolic locus, similar to P. aeruginosa GbdR, while GbdR2 is important to increase expression of the catabolic locus. Additionally, the B. thailandensis SouR ortholog (BTH_II0994) is required for catabolism of choline and its metabolites as carbon sources, whereas in P. aeruginosa, SouR function can by bypassed by GbdR. The strategy employed by B. thailandensis represents a distinct regulatory solution to control choline catabolism and thus provides both an evolutionary counterpoint and an experimental system to analyze the acquisition and regulation of this pathway during environmental growth and infection. Many proteobacteria that occupy similar environmental niches have horizontally acquired orthologous genes for metabolism of compounds useful in their shared environment. The arrangement and differential

[Present regulation on infant and follow-on formula].

Science.gov (United States)

Angulo Lucena, R; Gallego Domínguez, M C; Bentabol Manzanares, A; Jodral Villarejo, M

1995-01-01

The commercialization of breast milk substitutes has had great economic transcendence, sometimes without considering the sanitary and nutritional consequences for the customer. The sanitary authorities have been implied in this matter both in the International and European fields, issuing standards and regulations for the commercialization of breast milk substitutes which have been adopted by the Spanish Regulation. The aim of this paper is comment the regulations that affect foods for breast-feeding and short age children. This report analyzes and comments on the contents of international, european and national regulation on infant and follow-on formula. The regulations about Infant formula and Follow-on formula, banning the term of "humanized milk" and remarking the preference for breast feeding, which could only be substituted by sanitary professionals. This regulation deals with the appropriate chemical composition of these products, qualitative and quantitative. It includes standards for correct labeling, which should contain the appropriate information without idealizing the product Drawings and pictures showing the correct preparation are allowed. It provides for distribution and sales, as well as for correct advertising, which should be under control. This regulation also bans free samples and any other donation to particular customers or sanitary institutions. The present regulation on "Infant and Follow-on formulas" pursues the adequate nutrition of breast-feeding and short age children, being the protection of this kind of customers everyone's responsibility.

CIEMAT contribution to the international standard problem ISP-34: contain analysis of FAL-ISP 1 test

International Nuclear Information System (INIS)

Herranz, L.E.; Polo, J.

1994-01-01

CIEMAT, along with a great number of international laboratories, has participated in the open exercise of the first International Standard Problem addressing fission product transport issues. The FAL-ISP 1, aimed to study particle agglomeration, has been simulated with CONTAIN code. The thermalhydraulic results obtained have been satisfactory and aerosols ones have been reasonably accurate. However, some discrepancies appeared between predictions and experimental data; these are essentially related to the injection phase of the experiment, where the major influence of input approximations took place. In addition, the rationalization of discrepancies pointed potential data inconsistencies. Some parametric studies showed the results sensitivity to input assumptions concerning aerosol characterization and default values in CONTAIN; in general, they confirmed the suitability of most of the approximations taken. (Author)

STABILIZATION OF A MIXED WASTE SLUDGE SURROGATE CONTAINING MORE THAN 260 PPM MERCURY

International Nuclear Information System (INIS)

Smith, W. J.; Feizollahi, F.; Brimley, R.

2002-01-01

In an earlier demonstration of an innovative mercury stabilization technology for the Department of Energy, ATG's full-scale process stabilized mercury in soils that initially contained more than 260 ppm of mercury of unknown speciation. The treated waste satisfied the leaching standards for mercury that qualify wastes containing less than 260 ppm for land disposal. This paper describes the extension of that work to demonstrate a full-scale process for the stabilization of a representative sludge that contained more than 260 ppm of Hg of several mercury species. RCRA (Resource Conservation and Recovery Act) regulations now require the recovery of mercury from any waste containing more than 260 ppm of mercury, usually with thermal retorts. The results of this work with a surrogate sludge, and of the previous work with an actual soil, support a proposal now before the U.S. EPA (Environmental Protection Agency) to allow such wastes to be stabilized without retorting. The full-scale demonstration with a sulfide reagent reduced the mercury concentrations in extracts of treated sludge below the relevant leaching standard, a Universal Treatment Standard (UTS) limit of 0.025 mg mercury per liter of leachate generated by the Toxicity Characteristic Leaching Procedure (TCLP). The sulfide formulation reduced the concentration to about onehalf the UTS limit

SH2 domain-containing inositol 5-phosphatase (SHIP2) regulates de-novo lipogenesis and secretion of apoB100 containing lipoproteins in HepG2 cells.

Science.gov (United States)

Gorgani-Firuzjaee, Sattar; Khatami, Shohreh; Adeli, Khosrow; Meshkani, Reza

2015-09-04

Hepatic de-novo lipogenesis and production of triglyceride rich VLDL are regulated via the phosphoinositide 3-kinase cascade, however, the role of a negative regulator of this pathway, the SH2 domain-containing inositol 5-phosphatase (SHIP2) in this process, remains unknown. In the present study, we investigated the molecular link between SHIP2 expression and metabolic dyslipidemia using overexpression or suppression of SHIP2 gene in HepG2 cells. The results showed that overexpression of the wild type SHIP2 gene (SHIP2-WT) led to a higher total lipid content (28%) compared to control, whereas overexpression of the dominant negative SHIP2 gene (SHIP2-DN) reduced total lipid content in oleate treated cells by 40%. Overexpression of SHIP2-WT also led to a significant increase in both secretion of apoB100 containing lipoproteins and de-novo lipogenesis, as demonstrated by an enhancement in secreted apoB100 and MTP expression, increased intra and extracellular triglyceride levels and enhanced expression of lipogenic genes such as SREBP1c, FAS and ACC. On the other hand, overexpression of the SHIP2-DN gene prevented oleate-induced de-novo lipogenesis and secretion of apoB100 containing lipoproteins in HepG2 cells. Collectively, these findings suggest that SHIP2 expression level is a key determinant of hepatic lipogenesis and lipoprotein secretion, and its inhibition could be considered as a potential target for treatment of dyslipidemia. Copyright © 2015 Elsevier Inc. All rights reserved.

Towards an integrated design of voluntary approaches and standardization processes: An analysis of issues and trends in the Italian regulation on ground coupled heat pumps

International Nuclear Information System (INIS)

Rizzi, Francesco; Frey, Marco; Iraldo, Fabio

2011-01-01

Highlights: → We investigate GCHP regulation development from an entrepreneurial perspective. → Threats in booming market orient entrepreneurs toward green management. → Command and control regulation is not sufficient to guarantee market sustainability. → Voluntary regulation encourage best performers to invest in long-term strategies. → Bottom-up regulation design advances integration of process and product standards. - Abstract: Despite the lack of specific incentives, ground coupled heat pump (GCHP) installations are booming in Italy both in the private and public sectors. Such rapid growth is coupled with increasing concern for environmental and technical performances since no comprehensive regulation and reliable standards currently exist. This paper discusses potential schemes aimed at balancing mandatory and voluntary requirements by using SWOT-based techniques and examining the opinions of sectoral leaders. The analysis suggests that standardization and voluntary schemes are perceived as efficient and effective tools to encourage the greening of Italian GCHP-SMEs in the short-term while laying the foundations for sustainable policies in the longer run. A potential scheme is discussed that was simulated by reflecting the supply-side of the market, and which involves process and product standards.

Towards an integrated design of voluntary approaches and standardization processes: An analysis of issues and trends in the Italian regulation on ground coupled heat pumps

Energy Technology Data Exchange (ETDEWEB)

Rizzi, Francesco, E-mail: f.rizzi@sssup.it [Scuola Superiore Sant' Anna - Istituto di Management, P.zza Martiri della Liberta 33, 56127 Pisa (Italy); Frey, Marco, E-mail: frey@sssup.it [Scuola Superiore Sant' Anna - Istituto di Management, P.zza Martiri della Liberta 33, 56127 Pisa (Italy); Iraldo, Fabio, E-mail: f.iraldo@sssup.it [Scuola Superiore Sant' Anna - Istituto di Management, P.zza Martiri della Liberta 33, 56127 Pisa (Italy)

2011-09-15

Highlights: {yields} We investigate GCHP regulation development from an entrepreneurial perspective. {yields} Threats in booming market orient entrepreneurs toward green management. {yields} Command and control regulation is not sufficient to guarantee market sustainability. {yields} Voluntary regulation encourage best performers to invest in long-term strategies. {yields} Bottom-up regulation design advances integration of process and product standards. - Abstract: Despite the lack of specific incentives, ground coupled heat pump (GCHP) installations are booming in Italy both in the private and public sectors. Such rapid growth is coupled with increasing concern for environmental and technical performances since no comprehensive regulation and reliable standards currently exist. This paper discusses potential schemes aimed at balancing mandatory and voluntary requirements by using SWOT-based techniques and examining the opinions of sectoral leaders. The analysis suggests that standardization and voluntary schemes are perceived as efficient and effective tools to encourage the greening of Italian GCHP-SMEs in the short-term while laying the foundations for sustainable policies in the longer run. A potential scheme is discussed that was simulated by reflecting the supply-side of the market, and which involves process and product standards.

Dynamics of cocaine- and amphetamine-regulated transcript containing cell changes in the adrenal glands of two kidney, one clip rats.

Science.gov (United States)

Kasacka, Irena; Piotrowska, Zaneta; Janiuk, Izabela; Zbucki, Robert

2014-10-01

Taking into consideration the homeostatic disorders resulting from renal hypertension and the essential role of cocaine- and amphetamine-regulated transcript (CART) in maintaining homeostasis by regulating many functions of the body, the question arises as to what extent the renovascular hypertension affects the morphology and dynamics of changes of CART-containing cells in the adrenal glands. The aim of the present study was to examine the distribution, morphology, and dynamics of changes of CART-containing cells in the adrenal glands of "two kidney, one clip" (2K1C) renovascular hypertension model in rats. The studies were carried out on the adrenal glands of rats after 3, 14, 28, 42, and 91 days from the renal artery clipping procedure. To identify neuroendocrine cells, immunohistochemical reaction was performed with the use of a specific antibody against CART. It was revealed that renovascular hypertension causes changes in the endocrine cells containing CART in the adrenal glands of rats. The changes observed in the endocrine cells depend on the time when the rats with experimentally induced hypertension were examined. In the first period of hypertension, the number and immunoreactivity of CART-containing cells were decreased, while from the 28-day test, it significantly increased, as compared to the control rats. CART is relevant to the regulation of homeostasis in the cardiovascular system and seems to be involved in renovascular hypertension. The results of the present work open the possibility of new therapeutic perspectives for the treatment of arterial hypertension, since CART function is involved in their pathophysiology. © 2014 by the Society for Experimental Biology and Medicine.

Ciemat Contribution to The International Standard Problem ISP-34: Contain Analysis of Fal-ISP 1 Test

International Nuclear Information System (INIS)

Herranz, L. E.; Polo, J.

1994-01-01

CIEMAT, along with a great number of international laboratories, has participated in the open exercise of the first International Standard Problem addressing fission product transport issues. The FAL-ISP 1, aimed to study particle agglomeration, has been simulated with CONTAIN code. The therma hydraulic results obtained have been satisfactory and aerosol ones have been reasonably accurate. However, some discrepancies appeared between predictions and experimental data; these are essentially related to the injection phase of the experiment, where the major influence of input approximations took place. In addition, the rationalization of discrepancies pointed potential data inconsistencies. Some parametric studies showed the results sensitivity to input assumptions concerning aerosol characterization and default values in CONTAIN; in general, they confirmed the suitability of most of the approximations taken. (Author) 11 refs

Regulated programmed lysis of recombinant Salmonella in host tissues to release protective antigens and confer biological containment.

Science.gov (United States)

Kong, Wei; Wanda, Soo-Young; Zhang, Xin; Bollen, Wendy; Tinge, Steven A; Roland, Kenneth L; Curtiss, Roy

2008-07-08

We have devised and constructed a biological containment system designed to cause programmed bacterial cell lysis with no survivors. We have validated this system, using Salmonella enterica serovar Typhimurium vaccines for antigen delivery after colonization of host lymphoid tissues. The system is composed of two parts. The first component is Salmonella typhimurium strain chi8937, with deletions of asdA and arabinose-regulated expression of murA, two genes required for peptidoglycan synthesis and additional mutations to enhance complete lysis and antigen delivery. The second component is plasmid pYA3681, which encodes arabinose-regulated murA and asdA expression and C2-regulated synthesis of antisense asdA and murA mRNA transcribed from the P22 P(R) promoter. An arabinose-regulated c2 gene is present in the chromosome. chi8937(pYA3681) exhibits arabinose-dependent growth. Upon invasion of host tissues, an arabinose-free environment, transcription of asdA, murA, and c2 ceases, and concentrations of their gene products decrease because of cell division. The drop in C2 concentration results in activation of P(R), driving synthesis of antisense mRNA to block translation of any residual asdA and murA mRNA. A highly antigenic alpha-helical domain of Streptococcus pneumoniae Rx1 PspA was cloned into pYA3681, resulting in pYA3685 to test antigen delivery. Mice orally immunized with chi8937(pYA3685) developed antibody responses to PspA and Salmonella outer membrane proteins. No viable vaccine strain cells were detected in host tissues after 21 days. This system has potential applications with other Gram-negative bacteria in which biological containment would be desirable.

Proceedings of the Canadian Nuclear Society international conference on containment design

International Nuclear Information System (INIS)

Black, R.K.

1984-01-01

The subject of containment was discussed under the major topic headings of: USA views on containment design operation and regulation, containment structure analysis, containment envelope and energy suppression systems, European views on containment design operation and regulation, containment atmosphere control, Canadian views on containment design operation and regulation, containment analysis, and regulatory requirements, testing, and periodic inspection

Microcomputer relay regulator in the CAMAC standard

International Nuclear Information System (INIS)

Nikolaev, V.P.

1984-01-01

The digital relay regulator is developed on the base of the KM001 microcomputer and KK06 controller for automatic control ob ects with transfer functions describing a broad class of systems using actuating motors (stabilitation, follow-up systems). The CAMAC relay-unit realizes the regulation law and provides the possibility to control analogous values by 8 channels

76 FR 46805 - Notice of Utah Adoption by Reference of the Pesticide Container Containment Rule

Science.gov (United States)

2011-08-03

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9447-8] Notice of Utah Adoption by Reference of the Pesticide Container Containment Rule AGENCY: Environmental Protection Agency (EPA). ACTION: Notice. SUMMARY: This... Pesticide Container Containment (PCC) Rule regulations. In accordance with State of Utah Agricultural Code...

Neurons Containing Orexin or Melanin Concentrating Hormone Reciprocally Regulate Wake and Sleep

Directory of Open Access Journals (Sweden)

Roda Rani eKonadhode

2015-01-01

Full Text Available There is considerable amount of data on arousal neurons whereas there is a paucity of knowledge regarding neurons that make us fall asleep. Indeed, current network models of sleep-wake regulation list many arousal neuronal populations compared to only one sleep group located in the preoptic area. There are neurons outside the preoptic area that are active during sleep, but they have never been selectively manipulated. Indeed, none of the sleep-active neurons have been selectively stimulated. To close this knowledge gap we used optogenetics to selectively manipulate neurons containing melanin concentrating hormone (MCH. The MCH neurons are located in the posterior hypothalamus intermingled with the orexin arousal neurons. Our data indicated that optogenetic stimulation of MCH neurons in wildtype mice (J Neuroscience, 2013 robustly increased both non-REM and REM sleep. MCH neuron stimulation increased sleep during the animal’s normal active period, which is compelling evidence that stimulation of MCH neurons has a powerful effect in counteracting the strong arousal signal from all of the arousal neurons. The MCH neurons represent the only group of sleep-active neurons that when selectively stimulated induce sleep. From a translational perspective this is potentially useful in sleep disorders, such as insomnia, where sleep needs to be triggered against a strong arousal drive. Our studies indicate that the MCH neurons belong within an overall model of sleep-wake regulation.

SRY-box-containing gene 2 regulation of nuclear receptor tailless (Tlx) transcription in adult neural stem cells.

Science.gov (United States)

Shimozaki, Koji; Zhang, Chun-Li; Suh, Hoonkyo; Denli, Ahmet M; Evans, Ronald M; Gage, Fred H

2012-02-17

Adult neurogenesis is maintained by self-renewable neural stem cells (NSCs). Their activity is regulated by multiple signaling pathways and key transcription factors. However, it has been unclear whether these factors interplay with each other at the molecular level. Here we show that SRY-box-containing gene 2 (Sox2) and nuclear receptor tailless (TLX) form a molecular network in adult NSCs. We observed that both Sox2 and TLX proteins bind to the upstream region of Tlx gene. Sox2 positively regulates Tlx expression, whereas the binding of TLX to its own promoter suppresses its transcriptional activity in luciferase reporter assays. Such TLX-mediated suppression can be antagonized by overexpressing wild-type Sox2 but not a mutant lacking the transcriptional activation domain. Furthermore, through regions involved in DNA-binding activity, Sox2 and TLX physically interact to form a complex on DNAs that contain a consensus binding site for TLX. Finally, depletion of Sox2 revealed the potential negative feedback loop of TLX expression that is antagonized by Sox2 in adult NSCs. These data suggest that Sox2 plays an important role in Tlx transcription in cultured adult NSCs.

SRY-box-containing Gene 2 Regulation of Nuclear Receptor Tailless (Tlx) Transcription in Adult Neural Stem Cells*

Science.gov (United States)

Shimozaki, Koji; Zhang, Chun-Li; Suh, Hoonkyo; Denli, Ahmet M.; Evans, Ronald M.; Gage, Fred H.

2012-01-01

Adult neurogenesis is maintained by self-renewable neural stem cells (NSCs). Their activity is regulated by multiple signaling pathways and key transcription factors. However, it has been unclear whether these factors interplay with each other at the molecular level. Here we show that SRY-box-containing gene 2 (Sox2) and nuclear receptor tailless (TLX) form a molecular network in adult NSCs. We observed that both Sox2 and TLX proteins bind to the upstream region of Tlx gene. Sox2 positively regulates Tlx expression, whereas the binding of TLX to its own promoter suppresses its transcriptional activity in luciferase reporter assays. Such TLX-mediated suppression can be antagonized by overexpressing wild-type Sox2 but not a mutant lacking the transcriptional activation domain. Furthermore, through regions involved in DNA-binding activity, Sox2 and TLX physically interact to form a complex on DNAs that contain a consensus binding site for TLX. Finally, depletion of Sox2 revealed the potential negative feedback loop of TLX expression that is antagonized by Sox2 in adult NSCs. These data suggest that Sox2 plays an important role in Tlx transcription in cultured adult NSCs. PMID:22194602

Accounting standards

NARCIS (Netherlands)

Stellinga, B.; Mügge, D.

2014-01-01

The European and global regulation of accounting standards have witnessed remarkable changes over the past twenty years. In the early 1990s, EU accounting practices were fragmented along national lines and US accounting standards were the de facto global standards. Since 2005, all EU listed

Building a secondary containment system

Energy Technology Data Exchange (ETDEWEB)

Broder, M.F.

1994-10-01

Retail fertilizer and pesticide dealers across the United States are installing secondary containment at their facilities or are seriously considering it. Much of this work is in response to new state regulations; however, many dealers not facing new regulations are upgrading their facilities to reduce their liability, lower their insurance costs, or comply with anticipated regulations. The Tennessee Valley Authority`s (TVA) National Fertilizer and Environmental Research Center (NFERC) has assisted dealers in 22 states in retrofitting containment to their facilities. Simultaneous improvements in the operational efficiency of the facilities have been achieved at many of the sites. This paper is based on experience gained in that work and details the rationale used in planning secondary containment and facility modifications.

Standardization of the Manufacturing Process of Bee Venom Pharmacopuncture Containing Melittin as the Active Ingredient.

Science.gov (United States)

Lee, Yoonmi; Kim, Sung-Geun; Kim, In-Su; Lee, Hwa-Dong

2018-01-01

Pharmacopuncture is a unique treatment in oriental medicine that combines chemical stimulation with conventional acupuncture. However, there are no standardized methods for preparing the herbal medicines used in pharmacopuncture, and it is not clear whether the active ingredients are safe and stable. Several studies have investigated nonstandardized preparation processes, but few investigations have addressed safety and preparation methods. Pharmacopuncture may provide an alternative treatment for incurable diseases. However, it must be as valid and safe as standardized medicine. In this way, the present project may contribute to the industrialization of medicine in Korea. It may also expand health insurance coverage by promoting evidence-based medical insurance benefits. Thus, the present study attempted to standardize and improve the raw materials, preparation, and efficacy of bee venom pharmacopuncture (BVP), which is a highly effective technique in oriental medicine. To purify the crude bee venom, the extract was subjected to a stepped-gradient open column (ODS-A; 120 Å, 150 mesh). Using this method, the yield of melittin was significantly increased and the allergen proteins were effectively removed. The melittin content of the purified bee venom was determined using HPLC, and the product was then diluted to 0.1 mg/mL using injection water in preparation for BVP. In the present study, we standardized the purification process to provide safe and stable BVP by increasing the main effective components and eliminating allergens. This study will be seminal in the industrialization and regulation of BVP. We developed an effective strategy for melittin purification and allergen removal from bee venom to create safe BVP.

Branded prescription drug fee. Final regulations, temporary regulations, and removal of temporary regulations.

Science.gov (United States)

2014-07-28

This document contains final regulations that provide guidance on the annual fee imposed on covered entities engaged in the business of manufacturing or importing branded prescription drugs. This fee was enacted by section 9008 of the Patient Protection and Affordable Care Act, as amended by section 1404 of the Health Care and Education Reconciliation Act of 2010. This document also withdraws the Branded Prescription Drug Fee temporary regulations and contains new temporary regulations regarding the definition of controlled group that apply beginning on January 1, 2015. The final regulations and the new temporary regulations affect persons engaged in the business of manufacturing or importing certain branded prescription drugs. The text of the temporary regulations in this document also serves as the text of proposed regulations set forth in a notice of proposed rulemaking (REG-123286-14) on this subject in the Proposed Rules section in this issue of the Federal Register.

DER NEUE STANDARD IFRS 15 - IASB UND FASB VERABSCHIEDEN EINEN WEITGEHEND EINHEITLICHEN STANDARD ZUR UMSATZREALISIERUNG

OpenAIRE

Bodo Runzheimer

2015-01-01

The international accounting regulations regarding sales revenues have been changed. In May 2014, the International Accounting Standards Board (IASB) and the US regulator, the Financial Accounting Standards Board (FASB), published together new revenue recording regulations, which will be applied in IFRS (International Financial Reporting Standards) as well as in US-GAAP (United States Generally Accepted Accounting Principles). The core principle of the new IFRS 15 is that an entity will recog...

Regulating web content: the nexus of legislation and performance standards in the United Kingdom and Norway.

Science.gov (United States)

Giannoumis, G Anthony

2014-01-01

Despite different historical traditions, previous research demonstrates a convergence between regulatory approaches in the United Kingdom and Norway. To understand this convergence, this article examines how different policy traditions influence the legal obligations of performance standards regulating web content for use by persons with disabilities. While convergence has led to similar policy approaches, I argue that national policy traditions have an impact on how governments establish legal obligations for standards compliance. The analysis reveals that national policy traditions influenced antidiscrimination legislation and the capacity and authority of regulatory agencies, which impacted the diverging legal obligations of standards in the United Kingdom and Norway. The analysis further suggests that policy actors mediate the reciprocal influence between national policy traditions and regulatory convergence mechanisms. Copyright © 2014 John Wiley & Sons, Ltd.

Model Regulations for the Use of Radiation Sources and for the Management of the Associated Radioactive Waste. Supplement to IAEA Safety Standards Series No. GS-G-1.5

International Nuclear Information System (INIS)

2015-01-01

IAEA Safety Standards Series No. GSR Part 1, Governmental, Legal and Regulatory Framework for Safety, requires that governments establish laws and statutes to make provisions for an effective governmental, legal and regulatory framework for safety. The framework for safety includes the establishment of a regulatory body. The regulatory body has the authority and responsibility for promulgating regulations, and for preparing their implementation. This publication provides advice on an appropriate set of regulations covering all aspects of the use of radiation sources and the safe management of the associated radioactive waste. The regulations provide the framework for the regulatory requirements and conditions to be incorporated into individual authorizations for the use of radiation sources in industry, medical facilities, research and education and agriculture. The regulations also establish criteria to be used for assessing compliance. This publication allows States to appraise the adequacy of their existing regulations and regulatory guides, and can be used as a reference for those States developing regulations for the first time. The regulations set out in this publication will need to be adapted to take account of local conditions, technical resources and the scale of facilities and activities in the State. The set of regulations in this publication is based on the requirements established in the IAEA safety standards series, in particular in IAEA Safety Standards Series No. GSR Part 3 (Interim), Radiation Protection and Safety of Radiation Sources: International Basic Safety Standards, in IAEA Safety Standards Series No. GSR Part 5, Predisposal Management of Radioactive Waste, and in IAEA Safety Standards Series No. SSR-5, Disposal of Radioactive Waste. They are also derived from the Code of Conduct of the Safety and Security of Radiation Sources and the Guidance on the Import and Export of Radioactive Sources. This publication allows States to appraise the

Model Regulations for the Use of Radiation Sources and for the Management of the Associated Radioactive Waste. Supplement to IAEA Safety Standards Series No. GS-G-1.5

International Nuclear Information System (INIS)

2013-12-01

IAEA Safety Standards Series No. GSR Part 1, Governmental, Legal and Regulatory Framework for Safety, requires that governments establish laws and statutes to make provisions for an effective governmental, legal and regulatory framework for safety. The framework for safety includes the establishment of a regulatory body. The regulatory body has the authority and responsibility for promulgating regulations, and for preparing their implementation. This publication provides advice on an appropriate set of regulations covering all aspects of the use of radiation sources and the safe management of the associated radioactive waste. The regulations provide the framework for the regulatory requirements and conditions to be incorporated into individual authorizations for the use of radiation sources in industry, medical facilities, research and education and agriculture. The regulations also establish criteria to be used for assessing compliance. This publication allows States to appraise the adequacy of their existing regulations and regulatory guides, and can be used as a reference for those States developing regulations for the first time. The regulations set out in this publication will need to be adapted to take account of local conditions, technical resources and the scale of facilities and activities in the State. The set of regulations in this publication is based on the requirements established in the IAEA safety standards series, in particular in IAEA Safety Standards Series No. GSR Part 3 (Interim), Radiation Protection and Safety of Radiation Sources: International Basic Safety Standards, in IAEA Safety Standards Series No. GSR Part 5, Predisposal Management of Radioactive Waste, and in IAEA Safety Standards Series No. SSR-5, Disposal of Radioactive Waste. They are also derived from the Code of Conduct of the Safety and Security of Radiation Sources and the Guidance on the Import and Export of Radioactive Sources. This publication allows States to appraise the

Regulations and control of in-transit fumigated containers as well as of fumigated cargo ships.

Science.gov (United States)

Low, Anthony; Hüsing, Ulf-Peter; Preisser, Alexandra; Baur, Xaver

2003-01-01

According to IMO's international regulations, e.g. "Recommendations on the safe use of pesticides in ships", fumigated containers and ship cargoes must be labeled giving specifications about dates of fumigation and the fumigation gas used. Furthermore, appropriate certificates are necessary and these records have to be forwarded to the Port Health Authorities without their explicitly asking for them. According to IMO (DSC/Circ.8.24.7.2001) a recent inspection of containers unloaded in ports showed that some were under fumigation, but not declared as such and in a few cases these ventilated containers arrive with "Degas Certificates" stating that fumigant has been removed, but still have a high fumigant concentration inside when opened. There are similar reports from The Netherlands, where 21% of the fumigated containers had missing or false declarations and contained measurable amounts of toxic gas. In England 6% were mentioned to be allegedly false. Reports exist of a number of other incidents with containers under fumigation arriving in English ports with no accompanying documents on the ship or at the port of discharge as to the type of cargo. In one case several people were hospitalized after exposure to phosphine gas because the fumigant tablets were not yet totally decomposed before the ship arrived at its destination port. In Bavaria, Germany, a bad accident recently occurred through a non declared fumigated container (see press release). Our sample: a large container ship in the Port of Hamburg where 27 of the cargo's containers were found fumigated with 27 non/incomplete/false declarations. These examples show that missing/false labelling is frequent. Clearance of in-transit fumigated containers in ports is complicated and time-consuming for the captain and shipping company. The above mentioned accident and also the results of our spot check prove, as do the experiences in The Netherlands and England, that false declarations of fumigated containers seem

The design, manufacture, and testing of a new generation of ISO freight container for certification as an IP-2 package in compliance with the IAEA Regulations for the Safe Transport of Radioactive Material, 1985 edition (as amended 1990)

International Nuclear Information System (INIS)

Urch, K.C.

1997-01-01

Solid low level radioactive waste (LLW) which arises at nuclear power stations and other nuclear facilities in the UK, is routinely transported to British Nuclear Fuels' site at Drigg in Cumbria for disposal. A requirement was identified for the use of a refurbished ISO freight container of the full-height design, to transport drummed LLW to the site of a supercompaction facility prior to disposal at Drigg. This paper describes the reasoned technical justification employed for certifying the refurbished ISO freight container, Design No. 2912B, as an IP-2 package under Paragraph 523 of the IAEA Transport Regulations and the development of a new generation of ISO Freight container, Design No. 2044. It was recognised that the use of a refurbished container was only an interim measure and because of significant changes in the acceptance criteria for disposal, the increased use of high force compaction techniques and the proposed amendments to the IAEA Transport Regulations, Nuclear Electric embarked upon the development of a new generation of ISO freight containers. The new container design (Design No. 2044) incorporates a readily decontaminable stainless steel interior, a comprehensive load restraint system designed for the transport of single and multiple packages, and is lined with a polyurethane foam between the inner and outer skins. It is designed to transport 70 off, 200 litre drums of LLW (stacked in two layers) and other payloads of size not greater than 4 m long x 2 m wide and 20 tonnes in weight. The container was subjected to a range of tests to prove compliance with the ISO standard and the IAEA Transport Regulations. Following the preparation of the required documentation, in particular a Safety Case and comprehensive Operating and Maintenance Instructions, a Certificate of Regulatory Compliance was issued by the appropriate authority certifying the container as an Industrial Package Type 2 (IP-2) suitable for the transport of drummed LLW and other

Setting effective mandatory energy efficiency standards and labelling regulations: A review of best practices in the Asia Pacific region

International Nuclear Information System (INIS)

Shi, Xunpeng

2014-01-01

Highlights: • S and L regulations are needed to materialize the various benefits of energy efficiency. • S and L regulations can appear in various formats as in the Asia–Pacific region. • Effective regime has to be clear, authoritative, open, and enforceable. • Clear policy, customisation, inclusiveness, transparency and flexibility are desirable. - Abstract: This paper attempts to inform policy makers and legislators on how to set energy efficiency standards and labelling (S and L) regulations. It draws lessons from the literature on S and L regulations in the Asia–Pacific region and from practical experience in drafting the S and L regulations for Brunei Darussalam. The paper proposes necessary components for effective S and L regulations, as follows: clear liabilities, authoritative administration, open principles for technical systems, and enforceable mechanisms. It also recommends some key issues in good practice toward effective S and L regulations, such as policy making in advance, customised legislation, inclusive and transparent legislative procedure, and flexibility in the legislation

Environmental Radiation Protection Standards for Management and Disposal of Spent Nuclear Fuel and Transuranic Radioactive Wastes (40 CFR Part 191)

Science.gov (United States)

This regulation sets environmental standards for public protection from the management and disposal of spent nuclear fuel, high-level wastes and wastes that contain elements with atomic numbers higher than uranium (transuranic wastes).

48 CFR 12.214 - Cost Accounting Standards.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Cost Accounting Standards. 12.214 Section 12.214 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION... Items 12.214 Cost Accounting Standards. Cost Accounting Standards (CAS) do not apply to contracts and...

48 CFR 9903.307 - Cost Accounting Standards Preambles.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 7 2010-10-01 2010-10-01 false Cost Accounting Standards Preambles. 9903.307 Section 9903.307 Federal Acquisition Regulations System COST ACCOUNTING STANDARDS BOARD... ACCOUNTING STANDARDS CONTRACT COVERAGE CAS Rules and Regulations 9903.307 Cost Accounting Standards Preambles...

A critical evaluation of Internet marketing of products that contain ephedra.

Science.gov (United States)

Ashar, Bimal H; Miller, Redonda G; Getz, Kelly J; Pichard, Carmen P

2003-08-01

To evaluate information contained within Internet sites that advertise and market dietary supplements containing ephedra. We conducted an Internet search to identify Web sites advertising weight-loss supplements that contained ephedra. Between July 7 and July 18, 2002, 4 search engines were used by entering the term herbal weight loss. Outcome measures included disclosure of potential adverse effects of or contraindications to ephedra-containing supplements, disclosure of ephedra alkaloid dosage, and presence of misleading or incorrect information. Thirty-two products and advertisements were identified and systematically evaluated for deviance from truth-in-advertising standards. Of the 32 Web sites analyzed, 13 (41%) failed to disclose potential adverse effects or contraindications to supplement use. Seventeen (53%) did not reveal the dosage of ephedra alkaloids that was recommended. More importantly, 11 sites (34%) contained incorrect or misleading statements, some of which could directly result in serious harm to consumers. If dietary supplements containing ephedra are to continue to be marketed freely, substantial reform in advertising regulation and enforcement is warranted.

Standardization of the Manufacturing Process of Bee Venom Pharmacopuncture Containing Melittin as the Active Ingredient

Directory of Open Access Journals (Sweden)

Yoonmi Lee

2018-01-01

Full Text Available Background. Pharmacopuncture is a unique treatment in oriental medicine that combines chemical stimulation with conventional acupuncture. However, there are no standardized methods for preparing the herbal medicines used in pharmacopuncture, and it is not clear whether the active ingredients are safe and stable. Several studies have investigated nonstandardized preparation processes, but few investigations have addressed safety and preparation methods. Pharmacopuncture may provide an alternative treatment for incurable diseases. However, it must be as valid and safe as standardized medicine. In this way, the present project may contribute to the industrialization of medicine in Korea. It may also expand health insurance coverage by promoting evidence-based medical insurance benefits. Thus, the present study attempted to standardize and improve the raw materials, preparation, and efficacy of bee venom pharmacopuncture (BVP, which is a highly effective technique in oriental medicine. Method. To purify the crude bee venom, the extract was subjected to a stepped-gradient open column (ODS-A; 120 Å, 150 mesh. Using this method, the yield of melittin was significantly increased and the allergen proteins were effectively removed. The melittin content of the purified bee venom was determined using HPLC, and the product was then diluted to 0.1 mg/mL using injection water in preparation for BVP. Results. In the present study, we standardized the purification process to provide safe and stable BVP by increasing the main effective components and eliminating allergens. This study will be seminal in the industrialization and regulation of BVP. Conclusion. We developed an effective strategy for melittin purification and allergen removal from bee venom to create safe BVP.

21 CFR 610.60 - Container label.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 7 2010-04-01 2010-04-01 false Container label. 610.60 Section 610.60 Food and... GENERAL BIOLOGICAL PRODUCTS STANDARDS Labeling Standards § 610.60 Container label. (a) Full label. The following items shall appear on the label affixed to each container of a product capable of bearing a full...

Transports of radioactive materials. Legal regulations, safety and security concepts, experience

International Nuclear Information System (INIS)

Schwarz, Guenther

2012-01-01

In Germany, approximately 650,000 to 750,000 units containing radioactive materials for scientific, medical and technical applications are shipped annually by surface, air and water transports. Legally speaking, radioactive materials are dangerous goods which can cause hazards to life, health, property and the environment as a result of faulty handling or accidents in transit. For protection against these hazards, their shipment therefore is regulated in extensive national and international rules of protection and safety. The article contains a topical review of the international and national transport regulations and codes pertaining to shipments of radioactive materials, and of the protection concepts underlying these codes so as to ensure an adequate standard of safety and security in shipping radioactive materials in national and international goods traffic. (orig.)

CONTAIN code analyses of direct containment heating experiments

International Nuclear Information System (INIS)

Williams, D.C.; Griffith, R.O.; Tadios, E.L.; Washington, K.E.

1995-01-01

In some nuclear reactor core-melt accidents, a potential exists for molten core-debris to be dispersed into the containment under high pressure. Resulting energy transfer to the containment atmosphere can pressurize the containment. This process, known as direct containment heating (DCH), has been the subject of extensive experimental and analytical programs sponsored by the U.S. Nuclear Regulatory Commission (NRC). The DCH modeling has been an important focus for the development of the CONTAIN code. Results of a detailed independent peer review of the CONTAIN code were published recently. This paper summarizes work performed in support of the peer review in which the CONTAIN code was applied to analyze DCH experiments. Goals of this work were comparison of calculated and experimental results, CONTAIN DCH model assessment, and development of guidance for code users, including development of a standardized input prescription for DCH analysis

Benefits and disadvantages of self-regulation of environmental noise from military training

Science.gov (United States)

Luz, George A.

2002-05-01

In a 1981 Executive decision, the Administration's Office of Management and Budget (OMB) told the Environmental Protection Agency to end funding of the Office of Noise Abatement and Control (ONAC). This decision, coupled with a specific exemption for military equipment contained in the Noise Control Act of 1972, ensured that the military departments would be self-regulating in regard to noise. This self-regulation for noise stands in contrast to the external regulation of other pollutants, such as air and water emissions. Two possible disadvantages of self-regulation are (1) reduced funding for noise management compared with funding for externally regulated pollutants, and (2) lack of an independent and external set of standards for determining acceptable limits on community noise exposure. Three possible benefits are (1) avoiding the costs of mitigating trivial violations of external standards, (2) maintaining a long-standing policy of preventing noise problems through land use planning, and (3) enabling negotiated solutions between installations and their neighboring communities. The paper ends with an examination of a negotiated solution for a community subjected to noise from the detonation of obsolete ammunition.

Regulated programmed lysis of recombinant Salmonella in host tissues to release protective antigens and confer biological containment

OpenAIRE

Kong, Wei; Wanda, Soo-Young; Zhang, Xin; Bollen, Wendy; Tinge, Steven A.; Roland, Kenneth L.; Curtiss, Roy

2008-01-01

We have devised and constructed a biological containment system designed to cause programmed bacterial cell lysis with no survivors. We have validated this system, using Salmonella enterica serovar Typhimurium vaccines for antigen delivery after colonization of host lymphoid tissues. The system is composed of two parts. The first component is Salmonella typhimurium strain χ8937, with deletions of asdA and arabinose-regulated expression of murA, two genes required for peptidoglycan synthesis a...

7 CFR 925.13 - Container.

Science.gov (United States)

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Container. 925.13 Section 925.13 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... SOUTHEASTERN CALIFORNIA Definitions § 925.13 Container. Container means any lug, box, bag, crate, carton, or...

7 CFR 956.9 - Container.

Science.gov (United States)

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Container. 956.9 Section 956.9 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and... OF SOUTHEAST WASHINGTON AND NORTHEAST OREGON Definitions § 956.9 Container. Container means a box...

7 CFR 945.16 - Container.

Science.gov (United States)

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Container. 945.16 Section 945.16 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Container. Container means a sack, box, bag, crate, hamper, basket, carton, package, barrel, or any other...

Energy engineering. Standardization in the domain of coldness production; Genie energetique. Normalisation dans le domaine du froid

Energy Technology Data Exchange (ETDEWEB)

Legent, N. [Association Francaise de Normalisation (AFNOR), 92 - Paris-la-Defense (France)

2000-10-01

This paper deals with the recent advances in the domain of standardization and regulation of refrigeration and cold production systems used in the industry and in the commercial sector: 1 - international standardization; 2 - European standardization; 3 - international standardization in the domain of cold production (ISO/TC 86 'coldness and air conditioning', CEI 61C 'domestic refrigerating appliances', CEI 61D 'air-conditioning appliances for domestic and similar use', ISO/TC 104 'goods transportation containers'); 4 - European standardization in the domain of cold production (CEN/TC 182 'refrigerating systems - safety and environment requirements', CEN/TC 44 'household refrigerating appliances and refrigerating furniture for stores', CEN/TC 113 'heat pumps and air-conditioners', CEN/TC 141 'manometers and thermometers, measuring and recording means', CENELEC 61 'safety of domestic electrical appliances'); 5 - French standardization (international file, European file, French file, French standardization system); 6 - national standardization in other countries; 7 - regulations in the domain of cold production. (J.S.)

Environmental radiation standards

International Nuclear Information System (INIS)

Kocher, D.C.

1987-01-01

This document contains an outline of an oral presentation on environmental radiation standards presented to the American Nuclear Societies' Topical Conference on Population Exposure from the Nuclear Fuel Cycle. The paper contains several definitions, a summary of current radiation exposure limits; and numerous proposed changes to current standards. 7 figs

Nuclear safety review for qualification of class 1E motor inside containment for nuclear power stations

International Nuclear Information System (INIS)

Li Shixin; Wu Qi; Zhang Yunbo; Wu Caixia

2013-01-01

In nuclear power plants with pressurized water reactors, the review for class 1E motor inside containment qualification process and documents is an important aspect of nuclear safety equipment review, and the reviewers should make evaluations for the qualification test results in terms of the compliance with standard and regulation, and the consistency with inside containment environment. Firstly, this paper introduces the qualification test of class 1E motor inside containment for nuclear power generating stations, such as aging test and design-basis-event test. Second, there is a discussion about typical problems of review. At last, comparison of IEEE334 with RCC-E is conducted and explored. (authors)

7 CFR 924.17 - Container.

Science.gov (United States)

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Container. 924.17 Section 924.17 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Container. Container means a box, bag, crate, lug, basket, carton, package, or any other type of receptacle...

7 CFR 920.14 - Container.

Science.gov (United States)

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Container. 920.14 Section 920.14 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Definitions § 920.14 Container. Container means a box, bag, crate, lug, basket, carton, package, or any other...

48 CFR 1699.70 - Cost accounting standards.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 6 2010-10-01 2010-10-01 true Cost accounting standards... EMPLOYEES HEALTH BENEFITS ACQUISITION REGULATION CLAUSES AND FORMS COST ACCOUNTING STANDARDS Cost Accounting Standards 1699.70 Cost accounting standards. With respect to all experience-rated contracts currently...

7 CFR 958.17 - Container.

Science.gov (United States)

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Container. 958.17 Section 958.17 Agriculture... COUNTIES IN IDAHO, AND MALHEUR COUNTY, OREGON Order Regulating Handling Definitions § 958.17 Container. Container means a sack, box, bag, crate, hamper, basket, carton, package, or any other type of receptacle...

PHITS code improvements by Regulatory Standard and Research Department Secretariat of Nuclear Regulation Authority

International Nuclear Information System (INIS)

Goko, Shinji

2017-01-01

As for the safety analysis to be carried out when a nuclear power company applies for installation permission of facility or equipment, business license, design approval etc., the Regulatory Standard and Research Department Secretariat of Nuclear Regulation Authority continuously conducts safety research for the introduction of various technologies and their improvement in order to evaluate the adequacy of this safety analysis. In the field of the shielding analysis of nuclear fuel transportation materials, this group improved the code to make PHITS applicable to this field, and has been promoting the improvement as a tool used for regulations since FY2013. This paper introduced the history and progress of this safety research. PHITS 2.88, which is the latest version as of November 2016, was equipped with the automatic generation function of variance reduction parameters [T-WWG] etc., and developed as the tool equipped with many effective functions in practical application to nuclear power regulations. In addition, this group conducted the verification analysis against nuclear fuel packages, which showed a good agreement with the analysis by MCNP, which is extensively used worldwide and abundant in actual results. It also shows a relatively good agreement with the measured values, when considering differences in analysis and measurement. (A.O.)

7 CFR 51.911 - Container.

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Container. 51.911 Section 51.911 Agriculture... Standards for Grades of Table Grapes (European or Vinifera Type) 1 Definitions § 51.911 Container. Container... of grapes in packages containing 5 pounds or less, mean the master container in which the individual...

Components for containment enclosures. Part 4: Ventilation and gas-cleaning systems such as filters, traps, safety and regulation valves, control and protection devices

International Nuclear Information System (INIS)

2001-01-01

ISO 11933 consists of the following parts, under the general title Components for containment enclosures: Part 1: Glove/bag ports, bungs for glove/bag ports, enclosure rings and interchangeable units; Part 2: Gloves, welded bags, gaiters for remote-handling tongs and for manipulators; Part 3: Transfer systems such as plain doors, airlock chambers, double door transfer systems, leaktight connections for waste drums; Part 4: Ventilation and gas-cleaning systems such as filters, traps, safety and regulation valves, control and protection devices; Part 5: Penetrations for electrical and fluid circuits. This part of ISO 11933 specifies the design criteria and the characteristics of various components used for ventilation and gas-cleaning in containment enclosures. These components are either directly fixed to the containment enclosure wall, or used in the environment of a shielded or unshielded containment enclosure or line of such enclosures. They can be used alone or in conjunction with other mechanical components, including those specified in ISO 11933-1 and ISO 11933-3. This part of ISO 11933 is applicable to: filtering devices, including high-efficiency particulate air (HEPA) filters and iodine traps; safety valves and pressure regulators; systems ensuring the mechanical protection of containment enclosures; control and pressure-measurement devices

Using science soundly: The Yucca Mountain standard

International Nuclear Information System (INIS)

Fri, R.W.

1995-01-01

Using sound science to shape government regulation is one of the most hotly argued topics in the ongoing debate about regulatory reform. Even though no one advaocates using unsound science, the belief that even the best science will sweep away regulatory controversy is equally foolish. As chair of a National Research Council (NRC) committee that studied the scientific basis for regulating high-level nuclear waste disposal, the author learned that science alone could resolve few of the key regulatory questions. Developing a standard that specifies a socially acceptable limit on the human health effects of nuclear waste releases involves many decisions. As the NRC committee learned in evaluating the scientific basis for the Yucca Mountain standard, a scientifically best decision rarely exists. More often, science can only offer a useful framework and starting point for policy debates. And sometimes, science's most helpful contribution is to admit that it has nothing to say. The Yucca mountain study clearly illustrates that excessive faith in the power of science is more likely to produce messy frustration than crisp decisions. A better goal for regulatory reform is the sound use of science to clarify and contain the inevitable policy controversy

The epigenetic regulator Smchd1 contains a functional GHKL-type ATPase domain.

Science.gov (United States)

Chen, Kelan; Dobson, Renwick C J; Lucet, Isabelle S; Young, Samuel N; Pearce, F Grant; Blewitt, Marnie E; Murphy, James M

2016-06-15

Structural maintenance of chromosomes flexible hinge domain containing 1 (Smchd1) is an epigenetic regulator that plays critical roles in gene regulation during development. Mutations in SMCHD1 were recently implicated in the pathogenesis of facioscapulohumeral muscular dystrophy (FSHD), although the mechanistic basis remains of outstanding interest. We have previously shown that Smchd1 associates with chromatin via its homodimeric C-terminal hinge domain, yet little is known about the function of the putative GHKL (gyrase, Hsp90, histidine kinase, MutL)-type ATPase domain at its N-terminus. To formally assess the structure and function of Smchd1's ATPase domain, we have generated recombinant proteins encompassing the predicted ATPase domain and the adjacent region. Here, we show that the Smchd1 N-terminal region exists as a monomer and adopts a conformation resembling that of monomeric full-length heat shock protein 90 (Hsp90) protein in solution, even though the two proteins share only ∼8% overall sequence identity. Despite being monomeric, the N-terminal region of Smchd1 exhibits ATPase activity, which can be antagonized by the reaction product, ADP, or the Hsp90 inhibitor, radicicol, at a nanomolar concentration. Interestingly, introduction of an analogous mutation to that identified in SMCHD1 of an FSHD patient compromised protein stability, suggesting a possible molecular basis for loss of protein function and pathogenesis. Together, these results reveal important structure-function characteristics of Smchd1 that may underpin its mechanistic action at the chromatin level. © 2016 The Author(s). published by Portland Press Limited on behalf of the Biochemical Society.

CD44 staining of cancer stem-like cells is influenced by down-regulation of CD44 variant isoforms and up-regulation of the standard CD44 isoform in the population of cells that have undergone epithelial-to-mesenchymal transition.

Directory of Open Access Journals (Sweden)

Adrian Biddle

Full Text Available CD44 is commonly used as a cell surface marker of cancer stem-like cells in epithelial tumours, and we have previously demonstrated the existence of two different CD44(high cancer stem-like cell populations in squamous cell carcinoma, one having undergone epithelial-to-mesenchymal transition and the other maintaining an epithelial phenotype. Alternative splicing of CD44 variant exons generates a great many isoforms, and it is not known which isoforms are expressed on the surface of the two different cancer stem-like cell phenotypes. Here, we demonstrate that cancer stem-like cells with an epithelial phenotype predominantly express isoforms containing the variant exons, whereas the cancer stem-like cells that have undergone an epithelial-to-mesenchymal transition down-regulate these variant isoforms and up-regulate expression of the standard CD44 isoform that contains no variant exons. In addition, we find that enzymatic treatments used to dissociate cells from tissue culture or fresh tumour specimens cause destruction of variant CD44 isoforms at the cell surface whereas expression of the standard CD44 isoform is preserved. This results in enrichment within the CD44(high population of cancer stem-like cells that have undergone an epithelial-to-mesenchymal transition and depletion from the CD44(high population of cancer stem-like cells that maintain an epithelial phenotype, and therefore greatly effects the characteristics of any cancer stem-like cell population isolated based on expression of CD44. As well as effecting the CD44(high population, enzymatic treatment also reduces the percentage of the total epithelial cancer cell population staining CD44-positive, with potential implications for studies that aim to use CD44-positive staining as a prognostic indicator. Analyses of the properties of cancer stem-like cells are largely dependent on the ability to accurately identify and assay these populations. It is therefore critical that

Compliance determination procedures for environmental radiation protection standards for uranium recovery facilities 40 CFR part 190

International Nuclear Information System (INIS)

1982-03-01

Uranium Milling operations are licensed by the Nuclear Regulatory Commission and by some States in agreement with the Commission. The radiation dose to any individual from the operation of facilities within the uranium fuel cycle is limited to levels set by the Environmental Protection Agency. These levels are contained in the EPA Environmental Radiation Protection Standards for Nuclear Power Operations, in Part 190 of Title 40 of the Code of Federal Regulations (40 CFR Part 190). This report describes the procedures used within NRC's Uranium Recovery Licensing Branch for evaluating compliance with these regulations for uranium milling operations. The report contains descriptions of these procedures, dose factors for evaluating environmental measurement data, and guidance to the NRC staff reviewer

A performance-oriented and risk-based regulation for containment testing

International Nuclear Information System (INIS)

Dey, M.

1994-01-01

In August 1992, the NRC initiated a major initiative to develop requirements for containment testing that are less prescriptive, and more performance-oriented and risk-based. This action was a result of public comments and several studies that concluded that the economic burden of certain, present containment testing requirements are not commensurate with their safety benefits. The rulemaking will include consideration of relaxing the allowable containment leakage rate, increasing the interval for the integrated containment test, and establishing intervals for the local containment leak rate tests based on their performance. A study has been conducted to provide technical information for establishing the performance criteria for containment tests, the allowable leakage rate, commensurate with its significance to total public risk. The study used results of a recent comprehensive study conducted by the NRC, NUREG-1150, 'Severe Accident Risks: An Assessment for Five U.S. Nuclear Power Plants,' to examine the sensitivity of containment leakage to public risk. Risk was found to be insensitive to containment leakage rate up to levels of about 100 percent-volume per day for certain types of containments. PRA methods have also been developed to establish risk-based intervals for containment tests based on their past experience. Preliminary evaluations show that increasing the interval for the integrated containment leakage test from three times to once every ten years would have an insignificant impact on public risk. Preliminary analyses of operational experience data for local leak rate tests show that performance-based testing, valves and penetrations that perform well are tested less frequently, is feasible with marginal impact on safety. The above technical studies are being used to develop efficient (cost-effective) requirements for containment tests. (author). 4 refs., 2 figs

The general technical regulation and the standardization

International Nuclear Information System (INIS)

Laverie, Michel; Houze, Christian; Lebouleux, Philippe

1980-01-01

Through a certain number of procedures, the thorough appreciation of the safety of a nuclear installation relies more on a specific appreciation taking into account the references as a whole, than on a technical regulation which claims to cover all the problems. Nevertheless, a French technical regulation structure regarding the safety domain must be built up progressively. The authors consider the principles of such a structure, and together they make the inventory of the works, finished, in progress or contemplated. The description of this specifically French approach emphazises the multiple and complementary forms given to statutory implements [fr

Energy Building Regulations: The Effect of the Federal Performance Standards on Building Code Administration and the Conservation of Energy in New Buildings.

Science.gov (United States)

Kopper, William D.

1980-01-01

Explores the changes in the administration and enforcement of building regulations that will be engendered by the proposed federal energy building standards. Also evaluates the effectiveness of those standards in meeting congressional intent. Available from U.C. Davis Law Review, School of Law, Martin Luther King Jr. Hall, University of…

48 CFR 9903.101 - Cost Accounting Standards.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 7 2010-10-01 2010-10-01 false Cost Accounting Standards. 9903.101 Section 9903.101 Federal Acquisition Regulations System COST ACCOUNTING STANDARDS BOARD... ACCOUNTING STANDARDS CONTRACT COVERAGE General 9903.101 Cost Accounting Standards. Public Law 100-679 (41 U.S...

An intracellular motif of GLUT4 regulates fusion of GLUT4-containing vesicles.

Science.gov (United States)

Heyward, Catherine A; Pettitt, Trevor R; Leney, Sophie E; Welsh, Gavin I; Tavaré, Jeremy M; Wakelam, Michael J O

2008-05-20

Insulin stimulates glucose uptake by adipocytes through increasing translocation of the glucose transporter GLUT4 from an intracellular compartment to the plasma membrane. Fusion of GLUT4-containing vesicles at the cell surface is thought to involve phospholipase D activity, generating the signalling lipid phosphatidic acid, although the mechanism of action is not yet clear. Here we report the identification of a putative phosphatidic acid-binding motif in a GLUT4 intracellular loop. Mutation of this motif causes a decrease in the insulin-induced exposure of GLUT4 at the cell surface of 3T3-L1 adipocytes via an effect on vesicle fusion. The potential phosphatidic acid-binding motif identified in this study is unique to GLUT4 among the sugar transporters, therefore this motif may provide a unique mechanism for regulating insulin-induced translocation by phospholipase D signalling.

48 CFR 30.102 - Cost Accounting Standards Board publication.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Cost Accounting Standards... REGULATION GENERAL CONTRACTING REQUIREMENTS COST ACCOUNTING STANDARDS ADMINISTRATION General 30.102 Cost Accounting Standards Board publication. Copies of the CASB Standards and Regulations are printed in title 48...

Regulations No. 59 of 20 February 1978 on X-ray skin therapy equipment up to 50 kV

International Nuclear Information System (INIS)

1978-01-01

These regulations lay down the provisions to be complied with for the protection of medical staff and patients when using X-ray equipment for skin therapy. The operators of such equipment must comply with the technical guidelines contained in the regulations and provision is made for annual inspections to ensure that the devices meet the necessary safety standards. (NEA) [fr

Frontiers of environmental regulation: environmental management systems: a regulator`s perspective

Energy Technology Data Exchange (ETDEWEB)

Stone, M.J. [South Australian Dept. of Mines and Energy, Adelaide, SA (Australia)

1996-12-31

Leading edge companies throughout the world have embraced management systems to achieve optimal sustainable performance in the ever changing business environment of the 1990s. Given that the natural environment and environmental performance have become major issues affecting organizations, the need for integrating environmental management with all the other components of an organization`s overall management approach is now widely recognized. This paper is organized in five parts. The first explores recently released environmental standards, the interim environmental management systems (EMS) general guidelines standard AS/NZS ISO 14004 (Int) and identifies how this has dealt with the regulator/community/company interface. The second identifies company requirements for addressing environmental issues. The third, considers regulatory theory to identify current requirements for an effective regulatory system and how this can interface with a company`s EMS. These form the basis in the fourth section for identifying some opportunities which occur at the company/ regulator interface. The fifth and final section draws a number of conclusions about the current frontiers of environmental regulation. The coincidence of the requirements of a regulatory framework with the areas of interface between what is referred to in the draft International Standard for EMS as `Interested Parties`, the regulators and community, are identified. (author). 1 tab., 2 figs., 20 refs.

SRY-box-containing Gene 2 Regulation of Nuclear Receptor Tailless (Tlx) Transcription in Adult Neural Stem Cells

OpenAIRE

Shimozaki, Koji; Zhang, Chun-Li; Suh, Hoonkyo; Denli, Ahmet M.; Evans, Ronald M.; Gage, Fred H.

2012-01-01

Adult neurogenesis is maintained by self-renewable neural stem cells (NSCs). Their activity is regulated by multiple signaling pathways and key transcription factors. However, it has been unclear whether these factors interplay with each other at the molecular level. Here we show that SRY-box-containing gene 2 (Sox2) and nuclear receptor tailless (TLX) form a molecular network in adult NSCs. We observed that both Sox2 and TLX proteins bind to the upstream region of Tlx gene. Sox2 positively r...

Stowing the Right Containers on Container Vessels

DEFF Research Database (Denmark)

Jensen, Rune Møller

2014-01-01

’s largest container vessels using standard mathematical programming techniques and off-the-shelf solvers. The presentation will provide basic insight into the domain, with pointers to further information that enable you to join in this promising new path of operations research and business....

Benefits and Costs of Biologically Contained Genetically Modified Tomatoes and Eggplants in Italy and Spain

Directory of Open Access Journals (Sweden)

Rolf A. Groeneveld

2011-08-01

Full Text Available In this paper we assess the benefits and costs of introducing biologically contained genetically modified (GM crops, with an application to the potential introduction of GM tomatoes and eggplants in Italy and Spain. Such crops possess both the standard beneficial GM traits, and they prevent introgression of transgenes from GM crops to their conventional or wild relatives, thereby adding to the safety of their cultivation. As a result, coexistence regulations for these crops are less stringent than for crops without biological containment. The potential adoption of biologically contained GM tomatoes and eggplants is assessed in a cost-benefit framework for Italy and Spain. We conclude that biological containment has considerable potential benefits if policy makers are willing to loosen the restrictions on the introduction of these varieties.

Containment leakage rate testing requirements

International Nuclear Information System (INIS)

Arndt, E.G.

1992-01-01

This report presents the status of several documents under revision or development that provide requirements and guidance for testing nuclear power plant containment systems for leakage rates. These documents include the general revision to 10 CFR Part 50, Appendix J; the regulatory guide affiliated with the revision to Appendix J; the national standard that the regulatory guide endorses, ANSI/ANS-56.8, 'Containment System Leakage Rate Testing Requirements'; and the draft industry Licensing Topical Report, 'Standardized Program for Primary Containment Integrity Testing'. The actual or potential relationships between these documents are also explored

EU Regulation of Nanobiocides: Challenges in Implementing the Biocidal Product Regulation (BPR

Directory of Open Access Journals (Sweden)

Anna Brinch

2016-02-01

Full Text Available The Biocidal Products Regulation (BPR contains several provisions for nanomaterials (NMs and is the first regulation in the European Union to require specific testing and risk assessment for the NM form of a biocidal substance as a part of the information requirements. Ecotoxicological data are one of the pillars of the information requirements in the BPR, but there are currently no standard test guidelines for the ecotoxicity testing of NMs. The overall objective of this work was to investigate the implications of the introduction of nano-specific testing requirements in the BPR and to explore how these might be fulfilled in the case of copper oxide nanoparticles. While there is information and data available in the open literature that could be used to fulfill the BPR information requirements, most of the studies do not take the Organisation for Economic Co-operation and Development’s nanospecific test guidelines into consideration. This makes it difficult for companies as well as regulators to fulfill the BPR information requirements for nanomaterials. In order to enable a nanospecific risk assessment, best practices need to be developed regarding stock suspension preparation and characterization, exposure suspensions preparation, and for conducting ecotoxicological test.

EU Regulation of Nanobiocides: Challenges in Implementing the Biocidal Product Regulation (BPR).

Science.gov (United States)

Brinch, Anna; Hansen, Steffen Foss; Hartmann, Nanna B; Baun, Anders

2016-02-16

The Biocidal Products Regulation (BPR) contains several provisions for nanomaterials (NMs) and is the first regulation in the European Union to require specific testing and risk assessment for the NM form of a biocidal substance as a part of the information requirements. Ecotoxicological data are one of the pillars of the information requirements in the BPR, but there are currently no standard test guidelines for the ecotoxicity testing of NMs. The overall objective of this work was to investigate the implications of the introduction of nano-specific testing requirements in the BPR and to explore how these might be fulfilled in the case of copper oxide nanoparticles. While there is information and data available in the open literature that could be used to fulfill the BPR information requirements, most of the studies do not take the Organisation for Economic Co-operation and Development's nanospecific test guidelines into consideration. This makes it difficult for companies as well as regulators to fulfill the BPR information requirements for nanomaterials. In order to enable a nanospecific risk assessment, best practices need to be developed regarding stock suspension preparation and characterization, exposure suspensions preparation, and for conducting ecotoxicological test.

Standardization of the bakery goods

Directory of Open Access Journals (Sweden)

Elżbieta Goryńska-Goldmann

2010-01-01

Full Text Available The article presents selected aspects of the standardization, highly valued factor that stimulates the economic development of the country. The attention was paid to the purpose of the standardization, basic normative documents and standardizing activity. Different proposals for the classification of bread applied in practice or appearing in scientific studies were presented. It was emphasised that currently legal mess exists in Poland, in terms of use of the bread classification. The necessity of legal regulations of this issue by standard regulations was pointed out.

Code, standard and specifications

International Nuclear Information System (INIS)

Abdul Nassir Ibrahim; Azali Muhammad; Ab. Razak Hamzah; Abd. Aziz Mohamed; Mohamad Pauzi Ismail

2008-01-01

Radiography also same as the other technique, it need standard. This standard was used widely and method of used it also regular. With that, radiography testing only practical based on regulations as mentioned and documented. These regulation or guideline documented in code, standard and specifications. In Malaysia, level one and basic radiographer can do radiography work based on instruction give by level two or three radiographer. This instruction was produced based on guideline that mention in document. Level two must follow the specifications mentioned in standard when write the instruction. From this scenario, it makes clearly that this radiography work is a type of work that everything must follow the rule. For the code, the radiography follow the code of American Society for Mechanical Engineer (ASME) and the only code that have in Malaysia for this time is rule that published by Atomic Energy Licensing Board (AELB) known as Practical code for radiation Protection in Industrial radiography. With the existence of this code, all the radiography must follow the rule or standard regulated automatically.

77 FR 43196 - Minimum Internal Control Standards and Technical Standards

Science.gov (United States)

2012-07-24

... NATIONAL INDIAN GAMING COMMISSION 25 CFR Parts 543 and 547 Minimum Internal Control Standards [email protected] . SUPPLEMENTARY INFORMATION: Part 543 addresses minimum internal control standards (MICS) for Class II gaming operations. The regulations require tribes to establish controls and implement...

An intracellular motif of GLUT4 regulates fusion of GLUT4-containing vesicles

Directory of Open Access Journals (Sweden)

Welsh Gavin I

2008-05-01

Full Text Available Abstract Background Insulin stimulates glucose uptake by adipocytes through increasing translocation of the glucose transporter GLUT4 from an intracellular compartment to the plasma membrane. Fusion of GLUT4-containing vesicles at the cell surface is thought to involve phospholipase D activity, generating the signalling lipid phosphatidic acid, although the mechanism of action is not yet clear. Results Here we report the identification of a putative phosphatidic acid-binding motif in a GLUT4 intracellular loop. Mutation of this motif causes a decrease in the insulin-induced exposure of GLUT4 at the cell surface of 3T3-L1 adipocytes via an effect on vesicle fusion. Conclusion The potential phosphatidic acid-binding motif identified in this study is unique to GLUT4 among the sugar transporters, therefore this motif may provide a unique mechanism for regulating insulin-induced translocation by phospholipase D signalling.

Regulated and unregulated emissions from an internal combustion engine operating on ethanol-containing fuels

Science.gov (United States)

Poulopoulos, S. G.; Samaras, D. P.; Philippopoulos, C. J.

In the present work, the effect of ethanol addition to gasoline on regulated and unregulated emissions is studied. A 4-cylinder OPEL 1.6 L internal combustion engine equipped with a hydraulic brake dynamometer was used in all the experiments. For exhaust emissions treatment a typical three-way catalyst was used. Among the various compounds detected in exhaust emissions, the following ones were monitored at engine and catalyst outlet: methane, hexane, ethylene, acetaldehyde, acetone, benzene, 1,3-butadiene, toluene, acetic acid and ethanol. Addition of ethanol in the fuel up to 10% w/w had as a result an increase in the Reid vapour pressure of the fuel, which indicates indirectly increased evaporative emissions, while carbon monoxide tailpipe emissions were decreased. For ethanol-containing fuels, acetaldehyde emissions were appreciably increased (up to 100%), especially for fuel containing 3% w/w ethanol. In contrast, aromatics emissions were decreased by ethanol addition to gasoline. Methane and ethanol were the most resistant compounds to oxidation while ethylene was the most degradable compound over the catalyst. Ethylene, methane and acetaldehyde were the main compounds present at engine exhaust while methane, acetaldehyde and ethanol were the main compounds in tailpipe emissions for ethanol fuels after the catalyst operation.

Development of a standard reference material containing 22 chlorinated hydrocarbon gases at 1 μmol/mol in nitrogen.

Science.gov (United States)

Li, Ning; Du, Jian; Yang, Jing; Fan, Qiang; Tian, Wen

2017-11-01

A gas standard mixture containing 22 chlorinated hydrocarbons in high purity nitrogen was prepared using a two-step weighing method and a gasifying apparatus developed in-house. The concentration of each component was determined using a gas chromatograph with flame ionization detection (GC/FID). Linear regression analysis of every component was performed using the gas standard mixture with concentrations ranging from 1 to 10 μmol/mol, showing the complete gasification of volatile organic compound (VOCs) species in a selected cylinder. Repeatability was also examined to ensure the reliability of the preparation method. In addition, no significant difference was observed between domestic treated and imported treated cylinders, which were conducive to reduction of the cost of raw materials. Moreover, the results of stability testing at different pressures and long-term stability tests indicated that the gas standard at 1 μmol/mol level with relative expanded uncertainties of 5% was stable above 2 MPa for a minimum of 12 months. Finally, a quantity comparison was conducted between the gas standard and a commercial gas standard from Scott Specialty Gases (now Air Liquide America Specialty Gases). The excellent agreement of every species suggested the favorable accuracy of our gas standard. Therefore, this reference material can be applied to routine observation of VOCs and for other purposes.

41 CFR 101-29.218 - Voluntary standards.

Science.gov (United States)

2010-07-01

... Regulations System FEDERAL PROPERTY MANAGEMENT REGULATIONS SUPPLY AND PROCUREMENT 29-FEDERAL PRODUCT... standards,” but does not include professional standards of personal conduct, institutional codes of ethics...

Gap study on technical standards and quality assurance between ITER and Korean regulation

Energy Technology Data Exchange (ETDEWEB)

Kang, Myoung-suk [Kyung Hee University, Yongin-si 446-701, Gyeonggi-do (Korea, Republic of); Lee, Sangil; Lee, Hyoen Gon [National Fusion Research Institute, Daejeon-si 305-333 (Korea, Republic of); Heo, Gyunyoung, E-mail: gheo@khu.ac.kr [Kyung Hee University, Yongin-si 446-701, Gyeonggi-do (Korea, Republic of)

2016-11-01

Highlights: • This paper is to secure knowledge and expand domestic specialists for license and regulation of future fusion facilities including K-DEMO. - Abstract: Currently, Korea Domestic Agency (KODA) for the International Thermonuclear Experimental Reactor (ITER) project or the ITER Korea has been conducting follow-up surveys and development researches for the core technologies of its non-procurement items. This eventually aims to secure implicit as well as explicit knowledge and expand domestic specialists for future fusion facilities including K-DEMO. As a part of the project, the comparative analysis and gap study of technical standards and Quality Assurance (QA) system between ITER and Korean nuclear facilities are being performed. The goal of this study is to present a roadmap re-systematizing current safety-related standards for the fission-based facilities into fusion-based facilities in Republic of Korea. The research is considering two different tracks. First one is to secure the state-of-the-art of the fusion technical standards continually updated. For its investigation, we organized the Korean fusion safety advisory group that consists of experts from institutes, industries, and universities. The latest information of technical standards have been gathered and updated from each area of expert in periodic manner. The information is classified into Product Breakdown Structure (PBS) including safety classification, major safety issues, analysis computer codes, etc. This task will be re-organized this year such that the technical standards for procurement as well as non-procurement items can be accumulated in systematic and sustainable manner. Second one, called “Gap Study,” is to compare the requirements for domestic nuclear facilities and the results from the first track on the basis of experts’ opinion from the national and private sectors and to recommend the approaches to overcome technical and administrative barriers. The result is

Gap study on technical standards and quality assurance between ITER and Korean regulation

International Nuclear Information System (INIS)

Kang, Myoung-suk; Lee, Sangil; Lee, Hyoen Gon; Heo, Gyunyoung

2016-01-01

Highlights: • This paper is to secure knowledge and expand domestic specialists for license and regulation of future fusion facilities including K-DEMO. - Abstract: Currently, Korea Domestic Agency (KODA) for the International Thermonuclear Experimental Reactor (ITER) project or the ITER Korea has been conducting follow-up surveys and development researches for the core technologies of its non-procurement items. This eventually aims to secure implicit as well as explicit knowledge and expand domestic specialists for future fusion facilities including K-DEMO. As a part of the project, the comparative analysis and gap study of technical standards and Quality Assurance (QA) system between ITER and Korean nuclear facilities are being performed. The goal of this study is to present a roadmap re-systematizing current safety-related standards for the fission-based facilities into fusion-based facilities in Republic of Korea. The research is considering two different tracks. First one is to secure the state-of-the-art of the fusion technical standards continually updated. For its investigation, we organized the Korean fusion safety advisory group that consists of experts from institutes, industries, and universities. The latest information of technical standards have been gathered and updated from each area of expert in periodic manner. The information is classified into Product Breakdown Structure (PBS) including safety classification, major safety issues, analysis computer codes, etc. This task will be re-organized this year such that the technical standards for procurement as well as non-procurement items can be accumulated in systematic and sustainable manner. Second one, called “Gap Study,” is to compare the requirements for domestic nuclear facilities and the results from the first track on the basis of experts’ opinion from the national and private sectors and to recommend the approaches to overcome technical and administrative barriers. The result is

[Understanding and development strategy of health food containing Chinese materia medica].

Science.gov (United States)

Wang, Lin-Yuan; Zhang, Jian-Jun; Wang, Chun; Wang, Jing-Xia; Zhu, Ying-Li; Wang, Jia; Gao, Xue-Min

2016-11-01

Health food containing Chinese materia medica (CMM) conforms to the development demands of the age of big health and the theory of preventive treatment. In the view of health care and improvement of resisting diseases, it plays an important role in the market. It is very necessary to have further study and discussion on health food containing CMM. First of all, by comparing, analyzing and summarizing, the health food containing CMM could be defined as the health food which is qualified in security and functionality evaluation, with the traditional Chinese medicines(TCM) within TCM standards as the main raw materials, and the formulation-composition is based on the theory of TCM. It is characterized by higher safety than medicines, stronger biological activities than common food, multiple forms, abundant raw materials and integrated supervision and management. Secondly, we discussed the research and development (R&D) strategies and rules of health food containing CMM, pointing out that the core tasks of R&D include the investigation of formula, technology and the standards of quality. The fundamental principles of declaration and production include scientificity, rationality, reality and uniformity. Three key requirements (security, functionality and controllability) in the review as well as the process management of R&D and the key-points of risks control were summarized in this paper. Finally, the dynamic trends of policies and regulations related to health food containing CMM were analyzed in the view of registration, recording, raw materials and functions, and then related suggestions were proposed. Therefore, this article will be helpful in overall understanding the health food containing CMM and play a guiding role for its research and development. Copyright© by the Chinese Pharmaceutical Association.

7 CFR 201.42 - Small containers.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Small containers. 201.42 Section 201.42 Agriculture... REGULATIONS Sampling in the Administration of the Act § 201.42 Small containers. In sampling seed in small containers that it is not practical to sample as required in § 201.41, a portion of one unopened container or...

Russian Containers for Transportation of Solid Radioactive Waste

International Nuclear Information System (INIS)

Petrushenko, V. G.; Baal, E. P.; Tsvetkov, D. Y.; Korb, V. R.; Nikitin, V. S.; Mikheev, A. A.; Griffith, A.; Schwab, P.; Nazarian, A.

2002-01-01

The Russian Shipyard ''Zvyozdochka'' has designed a new container for transportation and storage of solid radioactive wastes. The PST1A-6 container is cylindrical shaped and it can hold seven standard 200-liter (55-gallon) drums. The steel wall thickness is 6 mm, which is much greater than standard U.S. containers. These containers are fully certified to the Russian GOST requirements, which are basically identical to U.S. and IAEA standards for Type A containers. They can be transported by truck, rail, barge, ship, or aircraft and they can be stacked in 6 layers in storage facilities. The first user of the PST1A-6 containers is the Northern Fleet of the Russian Navy, under a program sponsored jointly by the U.S. DoD and DOE. This paper will describe the container design and show how the first 400 containers were fabricated and certified

7 CFR 956.162 - Container markings.

Science.gov (United States)

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Container markings. 956.162 Section 956.162... WALLA VALLEY OF SOUTHEAST WASHINGTON AND NORTHEAST OREGON Rules and Regulations § 956.162 Container markings. Effective April 15, 1997, no handler shall ship any container of Walla Walla Sweet Onions except...

Safe drinking water act: Amendments, regulations and standards

International Nuclear Information System (INIS)

Calabrese, E.J.; Gilbert, C.E.; Pastides, H.

1989-01-01

This book approaches the topic of safe drinking water by communicating how the EPA has responded to the mandates of Congress. Chapter 1 summarizes what is and will be involved in achieving safe drinking water. Chapter 2 describes the historical development of drinking water regulations. Chapter 3 summarizes the directives of the Safe Drinking Water Act Amendments of 1986. Chapters 4 through 9 discuss each phase of the regulatory program in turn. Specific problems associated with volatile organic chemicals, synthetic organics, inorganic chemicals, and microbiological contaminants are assessed in Chapter 4 and 5. The unique characteristics of radionuclides and their regulation are treated in Chapter 6. The disinfection process and its resultant disinfection by-products are presented in Chapter 7. The contaminant selection process and the additional contaminants to be regulated by 1989 and 1991 and in future years are discussed in Chapters 8 and 9. EPA's Office of Drinking Water's Health Advisory Program is explained in Chapter 10. The record of public water system compliance with the primary drinking water regulations is detailed in Chapter 11. Chapter 12 offers a nongovernmental perspective on the general quality of drinking water and how this is affected by a wide range of drinking water treatment technologies. Separate abstracts are processed for 5 chapters in this book for inclusion in the appropriate data bases

Regulating household financial advice

Directory of Open Access Journals (Sweden)

Benjamin F. Cummings

2012-08-01

Full Text Available This paper reviews economic theory related to investment advice. This theory explains 1 why financial advisors need to be carefully regulated for the benefit of both the investment advice industry and for consumers, 2 why principles-based regulation (e.g., a fiduciary standard is more efficient than rules-based regulation, 3 why dual regulation of financial professionals providing investment or insurance advice is inefficient and inequitable policy, and 4 why the application of a universal and uniform fiduciary standard will be difficult to implement.

49 CFR 173.9 - Transport vehicles or freight containers containing lading which has been fumigated.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Transport vehicles or freight containers... MATERIALS REGULATIONS SHIPPERS-GENERAL REQUIREMENTS FOR SHIPMENTS AND PACKAGINGS General § 173.9 Transport... hazardous material. (b) No person may offer for transportation or transport a rail car, freight container...

Implementation in Russia and the European Union of International Safety Standards of Identity Documents with Biometric Data: Legal Regulation and Perspectives

Directory of Open Access Journals (Sweden)

Alexander Grigoryevich Volevodz

2015-01-01

Full Text Available The article contains the findings of a research into particular aspects of use of identity documents with personal biometric data. It considers the international safety standards of documents with biometric data worked out by the International Civil Aviation Organization (ICAO, pursuant to which those data should be included into machine-readable documents used by their holders for travel to various states. It contains the information on the implementation of these international standards in Russian and European Union law. The author has substantiated a conclusion to the effect that the procedure established in Russia for production and issuance, as well as for use of international, diplomatic and service passports identifying the Russian Federation citizen outside the Russian Federation territory, containing electronic information carriers with personal and biometric personal data, currently conforms to the international safety standards of documents with biometric data. The article surveys the experience of introducing domestic biometric identity documents - electronic passports in various countries of the world, and the problems arising therefrom. It substantiates the advantages and disadvantages of determining a passport of the Russian Federation citizen issued in the form of an identity card with an electronic information carrier, as the main document of the Russian Federation citizen identifying him domestically within the country's territory.

Review of the general regulation of radiological protection

International Nuclear Information System (INIS)

Cortes C, A.

2008-12-01

As a result of advances in radiation protection at the international level, the National Commission of Nuclear Safety and Safeguards has been given the task of revising the General Regulation of Radiation Safety to cover such developments, especially those contained in the safety basic standards No. 115 of the IAEA, published in 1977. In addition, the working group has considered issues that need to be regulated to avoid unnecessary dose received by the public due to exposure to ionizing radiation. Related to the public exposure believes the preliminary deal with situations of chronic exposure in homes, as well as human activities involving natural sources of ionizing radiation exposure to cause the public to levels that exceed the dose limits laid down in the Regulation. It is also envisaged that they will be subject to monitoring by the Commission, the concentration levels due to radon in homes, radon outdoor, radio and radon in drinking water, and external radiation levels due to naturally occurring radionuclides in building materials. Thus, the processes that may be subject to surveillance by the National Commission of Nuclear Safety and Safeguards include water treatment, some metallurgical processes, some of the mining industry and some industrial processes in which waste increase activity concentration of naturally occurring radionuclides. With the revision of the General Regulation of Radiation Safety, certain standards must be reviewed and further developed such as the concentration of radon levels in homes room, outdoor radon, radon and radio in drinking water, radiation levels out sourcing due to naturally occurring radionuclides in building materials, and standards governing (and identify) the radioactive material generation in the processes mentioned previously. (Author)

A compendium of major US radiation protection standards and guides

International Nuclear Information System (INIS)

Mills, W.A.; Flack, D.S.; Arsenault, F.J.; Conti, E.F.

1988-07-01

Following discussion of the general issue, the CIRRPC Executive Committee approved, with concurrence of the full Committee, an Oak Ridge Associated Universities (ORAU) staff proposal to develop a compendium of Fact Sheets on the major US radiation protection standards and guides, existing or proposed. The compendium contains relevant legal or statutory information and detailed technical requirements that state and describe the protection to be achieved. The report provides appropriate legislative citations; notes any legislative language that gave direction to the development of standards promulgated under the legislation; cites rationales for the standards promulgated; and provides a listing of related standards. Two consultants with considerable experience in radiation protection regulations were contracted to assist the ORAU staff in developing the report. This report has been reviewed twice by the CIRRPC member agencies; once to ensure the accuracy of all the legal and technical facts in the compendium, and once to comment on the entire document, including the accompanying text. This final report reflects consideration of all the agencies' comments received during the reviews. Part I of this report presents information on the selection, preparation and content of the Fact Sheets; an overview of their scopes, applications and modes of control; and the ORAU conclusions and recommendations. Part II contains the Fact Sheets and a User's Guide to finding relevant information in the Fact Sheets

Effects of national accounting standards convergence to international accounting standards on foreign direct investment

Directory of Open Access Journals (Sweden)

Asieh Farazandehnia

2015-09-01

Full Text Available One of the most important factors on attracting foreign investors to invest on Tehran Stock Exchange is to have transparent accounting rules and regulations. When there are some consistency between national accounting standards and international accounting standards, we may, at least, expect foreign investors to have better understanding on financial statements. In 2006, there were some changes on Iranian national accounting standards in an attempt to make them closer to international accounting standards. In this study, we select the information of 153 firms five years before and after this regulation and study the effect of convergence from national accounting standards to international accounting standards on foreign direct investment. Using some statistical tests, the study has determined that there was no meaningful relationship between foreign direct investment before and after change on accounting standards. In addition, there was no difference on the information quality before and after change on accounting standards. However, there was some meaningful relationship between the information quality and foreign direct investment.

75 FR 33744 - Pesticide Management and Disposal; Standards for Pesticide Containers and Containment; Proposed...

Science.gov (United States)

2010-06-15

... the likelihood of unreasonable adverse effects on human health and the environment. The container and... submitted soon. This is based on an evaluation of the resources and the time it would take for EPA to..., and the FIFRA Scientific Advisory Panel (SAP). The SAP and the Secretary of Agriculture waived review...

THE BASIS OF THE MARKET REGULATION OF PAYMENT CARDS

Directory of Open Access Journals (Sweden)

Khetagurov G. V.

2017-06-01

Full Text Available The article is devoted to basics and the regulation problems of the modern payment cards market. In particular, it addresses the key participants in a payment system, which include the Central Bank, credit organizations, settlement and clearing centers. The paper explores the basic functions of the participants. The author analyzes approaches of card payment systems to development and implementation monitoring of standards and regulations relative to the technology: hardware and software, communication channels, etc. The article contains analysis of information exchange in the framework of payment cards market and specific features of the design and development of a payment infrastructure. It discusses the economic model of the payment cards market, which is based on commission payments. The paper describes the key fees. At the final stage of the study, the author examines the role of different global regulators in the payment card market, conducts an analysis of the foundations of the Russian legislation regulating this market.

Los Alamos National Laboratory new generation standard nuclear material storage container - the SAVY4000 design

International Nuclear Information System (INIS)

Stone, Timothy Amos

2010-01-01

Incidents involving release of nuclear materials stored in containers of convenience such as food pack cans, slip lid taped cans, paint cans, etc. has resulted in defense board concerns over the lack of prescriptive performance requirements for interim storage of nuclear materials. Los Alamos National Laboratory (LANL) has shared in these incidents and in response proactively moved into developing a performance based standard involving storage of nuclear material (RD003). This RD003 requirements document has sense been updated to reflect requirements as identified with recently issued DOE M 441.1-1 'Nuclear Material Packaging Manual'. The new packaging manual was issued at the encouragement of the Defense Nuclear Facilities Safety Board with a clear directive for protecting the worker from exposure due to loss of containment of stored materials. The Manual specifies a detailed and all inclusive approach to achieve a high level of protection; from package design and performance requirements, design life determinations of limited life components, authorized contents evaluations, and surveillance/maintenance to ensure in use package integrity over time. Materials in scope involve those stored outside an approved engineered-contamination barrier that would result in a worker exposure of in excess of 5 rem Committed Effective Does Equivalent (CEDE). Key aspects of meeting the challenge as developed around the SAVY-3000 vented storage container design will be discussed. Design performance and acceptance criteria against the manual, bounding conditions as established that the user must ensure are met to authorize contents in the package (based upon the activity of heat-source plutonium (90% Pu-238) oxide, which bounds the requirements for weapons-grade plutonium oxide), interface as a safety class system within the facility under the LANL plutonium facility DSA, design life determinations for limited life components, and a sense of design specific surveillance program

Helicobacter pylori second-line rescue therapy with levofloxacin- and bismuth-containing quadruple therapy, after failure of standard triple or non-bismuth quadruple treatments.

Science.gov (United States)

Gisbert, J P; Romano, M; Gravina, A G; Solís-Muñoz, P; Bermejo, F; Molina-Infante, J; Castro-Fernández, M; Ortuño, J; Lucendo, A J; Herranz, M; Modolell, I; Del Castillo, F; Gómez, J; Barrio, J; Velayos, B; Gómez, B; Domínguez, J L; Miranda, A; Martorano, M; Algaba, A; Pabón, M; Angueira, T; Fernández-Salazar, L; Federico, A; Marín, A C; McNicholl, A G

2015-04-01

The most commonly used second-line Helicobacter pylori eradication regimens are bismuth-containing quadruple therapy and levofloxacin-containing triple therapy, both offering suboptimal results. Combining bismuth and levofloxacin may enhance the efficacy of rescue eradication regimens. To evaluate the efficacy and tolerability of a second-line quadruple regimen containing levofloxacin and bismuth in patients whose previous H. pylori eradication treatment failed. This was a prospective multicenter study including patients in whom a standard triple therapy (PPI-clarithromycin-amoxicillin) or a non-bismuth quadruple therapy (PPI-clarithromycin-amoxicillin-metronidazole, either sequential or concomitant) had failed. Esomeprazole (40 mg b.d.), amoxicillin (1 g b.d.), levofloxacin (500 mg o.d.) and bismuth (240 mg b.d.) was prescribed for 14 days. Eradication was confirmed by (13) C-urea breath test. Compliance was determined through questioning and recovery of empty medication envelopes. Incidence of adverse effects was evaluated by questionnaires. 200 patients were included consecutively (mean age 47 years, 67% women, 13% ulcer). Previous failed therapy included: standard clarithromycin triple therapy (131 patients), sequential (32) and concomitant (37). A total of 96% took all medications correctly. Per-protocol and intention-to-treat eradication rates were 91.1% (95%CI = 87-95%) and 90% (95%CI = 86-94%). Cure rates were similar regardless of previous (failed) treatment or country of origin. Adverse effects were reported in 46% of patients, most commonly nausea (17%) and diarrhoea (16%); 3% were intense but none was serious. Fourteen-day bismuth- and levofloxacin-containing quadruple therapy is an effective (≥90% cure rate), simple and safe second-line strategy in patients whose previous standard triple or non-bismuth quadruple (sequential or concomitant) therapies have failed. © 2015 John Wiley & Sons Ltd.

Proposals for Radiation (Emergency Preparedness and Public Information) Regulations (Northern Ireland). Consultative document

International Nuclear Information System (INIS)

2001-06-01

This Consultative Document (CD) contains proposals by the Health and Safety Executive for Northern Ireland (HSENI) for the Radiation (Emergency Preparedness and Public Information) Regulations (Northern Ireland) (REPPIR(NI)), to partly implement, for Northern Ireland, the articles on intervention in cases of radiological emergency contained in Council Directive 96/29/Euratom on the basic safety standards for the protection of the health of workers and the general public against the dangers arising from ionising radiation (Euratom BSS96 Directive), insofar as they apply to (a) premises, and (b) transport by rail

Private Animal Welfare Standards-Opportunities and Risks.

Science.gov (United States)

Lundmark, Frida; Berg, Charlotte; Röcklinsberg, Helena

2018-01-02

The current shift moves the governance of animal welfare away from the government towards the private market and the consumers. We have studied the intentions, content, and on-farm inspection results from different sets of animal welfare legislation and private standards with an aim to highlight the most important opportunities and risks identified in relation to the trend of increasingly relying on private standards for safeguarding or improving farm animal welfare. Our results show that different focuses, intentions, animal welfare requirements, inspection methods (i.e., methods for measuring and evaluating the compliance with a regulation), and inspection results, together with the use of vague wordings and a drive towards more flexible regulations does certainly not facilitate the interpretation and implementation of animal welfare regulations, especially not in relation to each other. Since farmers today often have to comply with several animal welfare regulations, including private standards, it is important to stress that a given regulation should never be seen as a single, stand-alone phenomenon, and the policymakers must hence consider the bigger picture, and apply the standards in relation to other existing regulations. This is especially relevant in relation to the legislation, a level that a private standard can never ignore.

7 CFR 1717.605 - Design standards, plans and specifications, construction standards, and RUS accepted materials.

Science.gov (United States)

2010-01-01

..., construction standards, and RUS accepted materials. 1717.605 Section 1717.605 Agriculture Regulations of the... standards, plans and specifications, construction standards, and RUS accepted materials. All borrowers... system design, construction standards, and the use of RUS accepted materials. Borrowers must comply with...

Study on Laws, Regulations and Standards on Energy Efficiency, Energy Conserving and Emission Reduction of Industrial Boilers in EU

Science.gov (United States)

Liu, Ren; Zhao, Yuejin; Chen, Haihong; Liang, Xiuying; Yang, Ming

2017-12-01

Industrial boilers are widely applied in such fields as factory power, building heating, and people’s lives; China is the world’s largest producer and user of industrial boilers, with very high annual energy consumption; clear requirements have been put forward by China on the energy efficiency since the “11th Five-year Plan” with the hope to save energy and reduce emission by means of energy efficiency standards and regulations on the supervision and control of various special equipment. So far, the energy efficiency of industrial boilers in China has been improved significantly but there is still a gap with the EU states. This paper analyzes the policies of energy efficiency, implementation models and methods of supervision and implementation at the EU level from laws, regulations, directives as well as standards; the paper also puts forward suggestions of energy conserving and emission reduction on the improvement of energy conserving capacity of industrial boilers in China through studying the legislations and measures of the developed countries in energy conserving of boilers.

Russian seismic standards and demands for equipment and their conformity with international standards

International Nuclear Information System (INIS)

Kaznovsky, S.; Ostretsov, I.

1993-01-01

The principle regulations of standard documents concerning seismic safety of NPPs and demands for reactor equipment conformity with international standards are presented in this report. General state of NPP safety standards is reviewed, with a special emphasis on the state of seismic design standards for NPP equipment and piping. Russian standards documents on seismic resistance of NPPs and requirements are compared to international ones

Operator licensing examiner standards

International Nuclear Information System (INIS)

1993-01-01

The Operator Licensing Examiner Standards provide policy and guidance to NRC examiners and establish the procedures and practices for examining licensees and applicants for reactor operator and senior reactor operator licenses at power reactor facilities pursuant to Part 55 of Title 10 of the Code of Federal Regulations (10 CFR 55). The Examiner Standards are intended to assist NRC examiners and facility licensees to better understand the initial and requalification examination processes and to ensure the equitable and consistent administration of examinations to all applicants. These standards are not a substitute for the operator licensing regulations and are subject to revision or other internal operator licensing policy changes

7 CFR 51.1863 - Standard weight.

Science.gov (United States)

2010-01-01

... Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE REGULATIONS AND STANDARDS UNDER THE AGRICULTURAL MARKETING ACT OF 1946... net weight of 15 pounds (6.80 kg) or more, the net weight of the contents shall not be less than the...

Radioactive waste disposal: Regulations and Application

International Nuclear Information System (INIS)

Hebert, Jean.

1977-01-01

The regulation of radioactive discharges, i.e. solid radioactive waste resulting from operation of nuclear installations and liquid and gazeous effluents released by them may be dealt with from two angles: the receiving environment and the polluting agent. French law covers both. Law on atmospheric pollution is based mainly on the Act of 2 August 1961 while the Act of 16 December 1964 governs water pollution. Both Acts have been the subject of a great number of implementing decrees, certain of which contain standards specific to radioactive pollution. Regulations on the polluting agent, namely its activity, comply with the generally established distinction between large nuclear installations and others. There again, there are many applicable texts, in particular, the Act of 19 July 1976 for classified installations, and the Decree of 11 December 1963, supplemented by the Decrees of 6 November 1974 and 31 December 1974 for large nuclear installations. This detailed analysis of national regulations is followed by a presentation of the applicable provisions in the Communities law and in international public law. (N.E.A.) [fr

Off-road compression-ignition engine emission regulations under the Canadian Environmental Protection Act 1999 : guidance document

International Nuclear Information System (INIS)

2006-03-01

This guide explained the requirements for Off-Road Compression Ignition Engine Emission Regulations established under the Canadian Environmental Protection Act. The regulations are enforced by Environment Canada, which authorizes and monitors the use of the national emissions mark. The regulations prescribe standards for off-road engines that operate as reciprocating, internal combustion engines, other than those that operate under characteristics similar to the Otto combustion cycle and that use a spark plug or other sparking device. The regulations apply to engines that are typically diesel-fuelled and found in construction, mining, farming and forestry machines such as tractors, excavators and log skidders. Four different types of persons are potentially affected by the regulations: Canadian engine manufacturers; distributors of Canadian engines or machines containing Canadian engines; importers of engines or machines for the purpose of sale; and persons not in companies importing engines or machines. Details of emission standards were presented, as well as issues concerning evidence of conformity, importing engines, and special engine cases. Compliance and enforcement details were reviewed, as well as applicable standards and provisions for emission control systems and defeat devices; exhaust emissions; crankcase and smoke emissions; and adjustable parameters. Details of import declarations were reviewed, as well as issues concerning defects and maintenance instructions. 4 tabs., 4 figs

Clarification of radiation-control regulations for diagnostic x-ray equipment

International Nuclear Information System (INIS)

1989-03-01

The Office of Compliance and Surveillance of the Center for Devices and Radiological Health (CDRH) has received many requests for interpretation of the Federal regulations that relate to diagnostic x-ray equipment. Responses to these requests were originally issued as FDA Compliance Policy Guides, industry-wide letters, and letters to individuals. The document is a compilation of those responses that remain applicable. Guides or opinions that have been withdrawn or are now obsolete because they have been incorporated into the regulations are not included. The document consists of two sections: the General section, which contains information of a general nature; and the Specific section, which contains information specific to particular sections of the Federal Performance Standard for Diagnostic X-ray Equipment (21 CFR 1020.30-32). When the term 'Revised Language' appears in an item heading, it indicates English grammar correction; the term 'Revised' indicates an updated version of the original clarification

Identification of a BET Family Bromodomain/Casein Kinase II/TAF-Containing Complex as a Regulator of Mitotic Condensin Function

Directory of Open Access Journals (Sweden)

Hyun-Soo Kim

2014-03-01

Full Text Available Condensin is a central regulator of mitotic genome structure with mutants showing poorly condensed chromosomes and profound segregation defects. Here, we identify NCT, a complex comprising the Nrc1 BET-family tandem bromodomain protein (SPAC631.02, casein kinase II (CKII, and several TAFs, as a regulator of condensin function. We show that NCT and condensin bind similar genomic regions but only briefly colocalize during the periods of chromosome condensation and decondensation. This pattern of NCT binding at the core centromere, the region of maximal condensin enrichment, tracks the abundance of acetylated histone H4, as regulated by the Hat1-Mis16 acetyltransferase complex and recognized by the first Nrc1 bromodomain. Strikingly, mutants in NCT or Hat1-Mis16 restore the formation of segregation-competent chromosomes in cells containing defective condensin. These results are consistent with a model where NCT targets CKII to chromatin in a cell-cycle-directed manner in order to modulate the activity of condensin during chromosome condensation and decondensation.

Identification of a BET family bromodomain/casein kinase II/TAF-containing complex as a regulator of mitotic condensin function.

Science.gov (United States)

Kim, Hyun-Soo; Mukhopadhyay, Rituparna; Rothbart, Scott B; Silva, Andrea C; Vanoosthuyse, Vincent; Radovani, Ernest; Kislinger, Thomas; Roguev, Assen; Ryan, Colm J; Xu, Jiewei; Jahari, Harlizawati; Hardwick, Kevin G; Greenblatt, Jack F; Krogan, Nevan J; Fillingham, Jeffrey S; Strahl, Brian D; Bouhassira, Eric E; Edelmann, Winfried; Keogh, Michael-Christopher

2014-03-13

Condensin is a central regulator of mitotic genome structure with mutants showing poorly condensed chromosomes and profound segregation defects. Here, we identify NCT, a complex comprising the Nrc1 BET-family tandem bromodomain protein (SPAC631.02), casein kinase II (CKII), and several TAFs, as a regulator of condensin function. We show that NCT and condensin bind similar genomic regions but only briefly colocalize during the periods of chromosome condensation and decondensation. This pattern of NCT binding at the core centromere, the region of maximal condensin enrichment, tracks the abundance of acetylated histone H4, as regulated by the Hat1-Mis16 acetyltransferase complex and recognized by the first Nrc1 bromodomain. Strikingly, mutants in NCT or Hat1-Mis16 restore the formation of segregation-competent chromosomes in cells containing defective condensin. These results are consistent with a model where NCT targets CKII to chromatin in a cell-cycle-directed manner in order to modulate the activity of condensin during chromosome condensation and decondensation. Copyright © 2014 The Authors. Published by Elsevier Inc. All rights reserved.

Evaluation of doses during the handling and transport of radioactive wastes containers

International Nuclear Information System (INIS)

Kubik, I.; Kusovska, Z.; Hanusik, V.; Mrskova, A.; Kapisovsky, V.

2000-01-01

Radioactive waste products from the nuclear power plants (NPPs) must be isolated from contact with people for very long period of time. Low and intermediate-level waste will be disposed of in Slovakia in specially licensed Regional disposal facility which is located near the NPP Mochovce site. Radioactive waste accumulated in the Jaslovsk. Bohunice site, during the decommissioning process of the NPP A-1 and arising from the NPP V-1 and NPP V-2 operation, will be processed and shipped in standard concrete containers to the Mochovce Regional disposal facility. The treatment centre was build at the NPP Jaslovsk? Bohunice site which is in the trial operation now. It is supposed that radioactive waste containers will be transported by train from the treatment centre Jaslovsk? Bohunice to the site of Radioactive Waste Repository at Mochovce and by truck in the area of repository. To estimate the occupational radiation exposure during the transport the calculations of dose rates from the containers are necessary. The national regulations allow low level of radiation to emanate from the casks and containers. The maximum permissible volume radioactivity of wastes inside the container is limited in such a way that irradiation level should not exceed 2 mGy/h for the contact irradiation level and 0,1 mGy/h at 2-meter distance. MicroShield code was used to analyse shielding and assessing exposure from gamma radiation of containers to people. A radioactive source was conservatively modelled by homogenous mixture of radionuclides with concrete. Standard rectangular volume source and shield geometry is used in model calculations. The activities of the personnel during the transport and storage of containers are analysed and results of the evaluation of external dose rates and effective doses are described. (author)

BioContainers: an open-source and community-driven framework for software standardization

Science.gov (United States)

da Veiga Leprevost, Felipe; Grüning, Björn A.; Alves Aflitos, Saulo; Röst, Hannes L.; Uszkoreit, Julian; Barsnes, Harald; Vaudel, Marc; Moreno, Pablo; Gatto, Laurent; Weber, Jonas; Bai, Mingze; Jimenez, Rafael C.; Sachsenberg, Timo; Pfeuffer, Julianus; Vera Alvarez, Roberto; Griss, Johannes; Nesvizhskii, Alexey I.; Perez-Riverol, Yasset

2017-01-01

Abstract Motivation BioContainers (biocontainers.pro) is an open-source and community-driven framework which provides platform independent executable environments for bioinformatics software. BioContainers allows labs of all sizes to easily install bioinformatics software, maintain multiple versions of the same software and combine tools into powerful analysis pipelines. BioContainers is based on popular open-source projects Docker and rkt frameworks, that allow software to be installed and executed under an isolated and controlled environment. Also, it provides infrastructure and basic guidelines to create, manage and distribute bioinformatics containers with a special focus on omics technologies. These containers can be integrated into more comprehensive bioinformatics pipelines and different architectures (local desktop, cloud environments or HPC clusters). Availability and Implementation The software is freely available at github.com/BioContainers/. Contact yperez@ebi.ac.uk PMID:28379341

BioContainers: an open-source and community-driven framework for software standardization.

Science.gov (United States)

da Veiga Leprevost, Felipe; Grüning, Björn A; Alves Aflitos, Saulo; Röst, Hannes L; Uszkoreit, Julian; Barsnes, Harald; Vaudel, Marc; Moreno, Pablo; Gatto, Laurent; Weber, Jonas; Bai, Mingze; Jimenez, Rafael C; Sachsenberg, Timo; Pfeuffer, Julianus; Vera Alvarez, Roberto; Griss, Johannes; Nesvizhskii, Alexey I; Perez-Riverol, Yasset

2017-08-15

BioContainers (biocontainers.pro) is an open-source and community-driven framework which provides platform independent executable environments for bioinformatics software. BioContainers allows labs of all sizes to easily install bioinformatics software, maintain multiple versions of the same software and combine tools into powerful analysis pipelines. BioContainers is based on popular open-source projects Docker and rkt frameworks, that allow software to be installed and executed under an isolated and controlled environment. Also, it provides infrastructure and basic guidelines to create, manage and distribute bioinformatics containers with a special focus on omics technologies. These containers can be integrated into more comprehensive bioinformatics pipelines and different architectures (local desktop, cloud environments or HPC clusters). The software is freely available at github.com/BioContainers/. yperez@ebi.ac.uk. © The Author(s) 2017. Published by Oxford University Press.

7 CFR 1434.8 - Containers and drums.

Science.gov (United States)

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false Containers and drums. 1434.8 Section 1434.8... REGULATIONS FOR HONEY § 1434.8 Containers and drums. (a)(1) To be eligible for assistance under this part, honey must be packed in: (i) CCC-approved, 5-gallon plastic containers; (ii) 5-gallon metal containers...

Recent changes in federal PCB regulations

International Nuclear Information System (INIS)

Ewing, H.

1995-01-01

An overview of the federal regulations dealing with PCBs, the draft PCB Transformer Decontamination Standards and Protocols, and the Practice of Ballast Splitting was given. Answers were provided to practical questions concerning the regulations, specifically, responsibility for storage, labelling requirements, waste export regulations, treatment and destruction standards, transformer decontamination, decontamination standards, and the practice of ballast splitting into PCB and non-PCB materials. Details of sampling procedures and sample handling were also described

Joint FAO/WHO food standards programme coordinating committee for Europe 16. session Vienna, Austria, 27 June - 1 July 1988

International Nuclear Information System (INIS)

1988-02-01

A brief paper is presented containing data on the use of irradiation processes in foodstuffs in European countries and summarizing the status of applications of food irradiation. Problem of consumer acceptance are highlighted, and the requirement for standardization of regulations to encourage international trade in irradiated food is discussed. 1 fig., 1 tab

Air pollution control regulation. [Japan

Energy Technology Data Exchange (ETDEWEB)

Sogabe, K

1975-05-01

The Basic Law for Environmental Pollution Control is reviewed. The fundamental ideology of pollution control, range of pollution control, environmental standards, and national policy concerning pollution control are discussed. The content of the Air Pollution Control Law is summarized. The purpose of the Air Pollution Control Law, a list of substances regulated by the law, the type of facilities regulated by the law, control standards, type of control means, and emission standards for flue gas (sulfur oxides, particulate matters, and toxic substances) are described. The environmental standard for each pollutant and the target date for achieving the environmental standard are also given. The list of cities where the 7-rank K value control regulation for SOx is enforced is given. The procedure for registration in compliance with the law is also described.

Development of prestressed concrete containment vessels

International Nuclear Information System (INIS)

Yuji, Hideo; Kuniyoshi, Mutsumu; Nagata, Kaoru

1983-01-01

This paper presents a summary of evaluations for the selection of the structural and prestressing system type to be employed for the first domestic Prestressed Concrete Containment Vessel (PCCV) in Japan. This paper also discusses characteristic features in the design of the liner plate system provided on the PCCV inner surface to assure its leak-tight integrity. Prestressed concrete containment vessels so far constructed in foreign countries are to a considerable extent of different structural types, depending on differences in dome shapes, prestressing systems and number of buttresses. These differences are caused not only by differences in design philosophy and construction practices, but also by difference in the level of technology of the times when the individual containment vessels are being constructed. In the investigation reported herein, the most suitable types of PCCV and Prestressing Systems were determined as the results of an overall comparative evaluation of data and information obtained from PCCV's so far constructed from the design, construction and cost aspects, taking into consideration the seismic criteria, available technology, construction practices, regulations and technical standards in Japan. The function of the liner plate system requires the liner to have enough deformability so that the liner deformation can be consistent with the PCCV concrete deformation. Therefore, in the design of the liner plate system a method for evaluating liner deformability was employed, instead of the stress evaluation method which is widely used in the design of ordinary structures. (author)

Operator licensing examiner standards

International Nuclear Information System (INIS)

1983-10-01

The Operator Licensing Examiner Standards provide policy and guidance to NRC examiners and establish the procedures and practices for examining and licensing of applicants for NRC operator licenses pursuant to Part 55 of Title 10 of the Code of Federal Regulations (10 CFR 55). They are intended to assist NRC examiners and facility licensees to understand the examination process better and to provide for equitable and consistent administration of examinations to all applicants by NRC examiners. These standards are not a substitute for the operator licensing regulations and are subject to revision or other internal operator examination licensing policy changes. As appropriate, these standards will be revised periodically to accommodate comments and reflect new information or experience

7 CFR 3015.61 - Financial management standards.

Science.gov (United States)

2010-01-01

... 7 Agriculture 15 2010-01-01 2010-01-01 false Financial management standards. 3015.61 Section 3015.61 Agriculture Regulations of the Department of Agriculture (Continued) OFFICE OF THE CHIEF FINANCIAL OFFICER, DEPARTMENT OF AGRICULTURE UNIFORM FEDERAL ASSISTANCE REGULATIONS Standards for Financial...

The use of innovation action research approach in the preparation of a regulation on costing standard 

Directory of Open Access Journals (Sweden)

Monika Raulinajtys-Grzybek

2016-04-01

Full Text Available The article analyzes the applicability of the innovation action research method for activities related to the preparation of a concept of a costing standard for healthcare providers which is subject to legal regula- tion. This legislation regulates the way providers, reporting data for the purpose of the regulated pricing of health services, identify and calculate costs. A 39-month long research project was carried out in ac- cordance with the innovation action research approach, which resulted in the creation of a novel concept of a costing model. The generation of new knowledge occurred as a result of a collaboration between researchers and practitioners, which is a basic assumption of action research. The consecutive steps of the research have been characterized in order to present the influence of the research method on the devel- opment and modification of the initial concept.

Survey of legal aspects, regulations, standards and guidelines applicable to radioactive waste management of the Brazilian Multipurpose Reactor - RMB

International Nuclear Information System (INIS)

Salvetti, T.C.; Marumo, J.T.

2017-01-01

In Brazil, the Brazilian Nuclear Energy Commission (CNEN) and Brazilian Institute of Environment and Renewable Natural Resources (IBAMA) are the agencies responsible for the execution, regulation and control of nuclear and environmental policies, respectively. Such regulatory activities are very comprehensive (IBAMA) or too specific (CNEN), revealing other aspects that would, also, need to be observed so that the management could be carried out efficiently (quality) and effectively (safety), including the three governmental administrative levels: Federal, State and Municipal. In addition to laws, regulations, decrees and resolutions, there are also national and international standards and guides that provide guidelines for structuring the current management and the use of best regulatory practices. The Brazilian Multipurpose Reactor Enterprise (RMB) is a CNEN project, complying with a Multi-Year Plan of the Brazilian Ministry of Planning, Development and Management (MPDG). The Enterprise is being developed under the responsibility of the Directorate of Research and Development - DPD of CNEN and will have a facility for treatment and initial temporary storage of the radioactive waste generated by the operation of the research reactor and the activities carried out in the associated laboratories. The RMB will be built in the city of IPERÓ, located in the state of São Paulo, near ARAMAR Experimental Center of the Brazilian Navy. This work aims to present the research results regarding the various aspects that regulate, legislate and standardize the practices proposed to the Radioactive Waste Management of the RMB project. (author)

Survey of legal aspects, regulations, standards and guidelines applicable to radioactive waste management of the Brazilian Multipurpose Reactor - RMB

Energy Technology Data Exchange (ETDEWEB)

Salvetti, T.C.; Marumo, J.T., E-mail: salvetti@ipen.br [Instituto de Pesquisas Energéticas e Nucleares (IPEN/CNEN-SP), São Paulo, SP (Brazil)

2017-07-01

In Brazil, the Brazilian Nuclear Energy Commission (CNEN) and Brazilian Institute of Environment and Renewable Natural Resources (IBAMA) are the agencies responsible for the execution, regulation and control of nuclear and environmental policies, respectively. Such regulatory activities are very comprehensive (IBAMA) or too specific (CNEN), revealing other aspects that would, also, need to be observed so that the management could be carried out efficiently (quality) and effectively (safety), including the three governmental administrative levels: Federal, State and Municipal. In addition to laws, regulations, decrees and resolutions, there are also national and international standards and guides that provide guidelines for structuring the current management and the use of best regulatory practices. The Brazilian Multipurpose Reactor Enterprise (RMB) is a CNEN project, complying with a Multi-Year Plan of the Brazilian Ministry of Planning, Development and Management (MPDG). The Enterprise is being developed under the responsibility of the Directorate of Research and Development - DPD of CNEN and will have a facility for treatment and initial temporary storage of the radioactive waste generated by the operation of the research reactor and the activities carried out in the associated laboratories. The RMB will be built in the city of IPERÓ, located in the state of São Paulo, near ARAMAR Experimental Center of the Brazilian Navy. This work aims to present the research results regarding the various aspects that regulate, legislate and standardize the practices proposed to the Radioactive Waste Management of the RMB project. (author)

Residual Stresses In 3013 Containers

International Nuclear Information System (INIS)

Mickalonis, J.; Dunn, K.

2009-01-01

The DOE Complex is packaging plutonium-bearing materials for storage and eventual disposition or disposal. The materials are handled according to the DOE-STD-3013 which outlines general requirements for stabilization, packaging and long-term storage. The storage vessels for the plutonium-bearing materials are termed 3013 containers. Stress corrosion cracking has been identified as a potential container degradation mode and this work determined that the residual stresses in the containers are sufficient to support such cracking. Sections of the 3013 outer, inner, and convenience containers, in both the as-fabricated condition and the closure welded condition, were evaluated per ASTM standard G-36. The standard requires exposure to a boiling magnesium chloride solution, which is an aggressive testing solution. Tests in a less aggressive 40% calcium chloride solution were also conducted. These tests were used to reveal the relative stress corrosion cracking susceptibility of the as fabricated 3013 containers. Significant cracking was observed in all containers in areas near welds and transitions in the container diameter. Stress corrosion cracks developed in both the lid and the body of gas tungsten arc welded and laser closure welded containers. The development of stress corrosion cracks in the as-fabricated and in the closure welded container samples demonstrates that the residual stresses in the 3013 containers are sufficient to support stress corrosion cracking if the environmental conditions inside the containers do not preclude the cracking process.

NEURO-SYSTEM OF AIMING AND STABILIZING WITH A REGULATOR ON THE BASIS OF STANDARD MODEL MODEL REFERENCE CONTROLLER

Directory of Open Access Journals (Sweden)

B.I. Kuznetsov

2015-08-01

Full Text Available The aim of this work is the synthesis of neural network aiming and stabilization system for the special equipment of moving objects with neuro-controller on the basis of standard model and performance comparison of the neural network system with the neural network predictive control. Build a block diagram of the neural network aiming and stabilization system, based on the subject control principle with PD-regulator in the position loop and with neuro-controller on the basis of standard model in the in the velocity loop. The neuro-controller on the basis of standard model Model Reference Controller is synthesized in the MATLAB Neural Network Toolbox and system simulation is performed. The studies show that the transient state variables of the system are oscillatory. Therefore, the neuro-controller with the prediction NN Predictive Controller should be used for aiming and stabilizing system to provide high dynamic characteristics achieved at the cost of higher complexity and computational cost.

Regulation on control systems tests

International Nuclear Information System (INIS)

Grau, J.; Navarro, J.M.

1978-01-01

Requirements under regulation applicable to the testing of control systems and controlled equipments in the case of USA nuclear projects are examined. They are reviewed, in particular, the following standards and criteria: 10 Code of Federal Regulations 50, Appendix A, General Design Criteria 20 and 21; IEEE Standards 279 and 308; IEEE Standard 338; US Regulatory Guides 1.22 and 1.118.(J.E.de C.)

Fabrication of 12% 240Pu calorimetry standards

International Nuclear Information System (INIS)

Long, S.M.; Hildner, S.; Gutierrez, D.; Mills, C.; Garcia, W.; Gurule, C.

1995-01-01

Throughout the DOE complex, laboratories are performing calorimetric assays on items containing high burnup plutonium. These materials contain higher isotopic range and higher wattages than materials previously encountered in vault holdings. Currently, measurement control standards have been limited to utilizing 6% 240 Pu standards. The lower isotopic and wattage value standards do not complement the measurement of the higher burnup material. Participants of the Calorimetry Exchange (CALEX) Program have identified the need for new calorimetric assay standards with a higher wattage and isotopic range. This paper describes the fabrication and verification measurements of the new CALEX standard containing 12% 240 Pu oxide with a wattage of about 6 to 8 watts

From Topos to Oikos: The Standardization of Glass Containers as Epistemic Boundaries in Modern Laboratory Research (1850-1900).

Science.gov (United States)

Espahangizi, Kijan

2015-09-01

Glass vessels such as flasks and test tubes play an ambiguous role in the historiography of modern laboratory research. In spite of the strong focus on the role of materiality in the last decades, the scientific glass vessel - while being symbolically omnipresent - has remained curiously neglected in regard to its materiality. The popular image or topos of the transparent, neutral, and quasi-immaterial glass container obstructs the view of the physico-chemical functionality of this constitutive inner boundary in modern laboratory environments and its material historicity. In order to understand how glass vessels were able to provide a stable epistemic containment of spatially enclosed experimental phenomena in the new laboratory ecologies emerging in the nineteenth and early twentieth century, I will focus on the history of the material standardization of laboratory glassware. I will follow the rise of a new awareness for measurement errors due to the chemical agency of experimental glass vessels, then I will sketch the emergence of a whole techno-scientific infrastructure for the improvement of glass container quality in late nineteenth-century Germany. In the last part of my argument, I will return to the laboratory by looking at the implementation of this glass reform that created a new oikos for the inner experimental milieus of modern laboratory research.

Product unconformable in the light of legal regulations and the ISO 9001:2000 standards

Directory of Open Access Journals (Sweden)

Justyna Górna

2009-01-01

Full Text Available The supervision of unconformable product is a key problem in the era of globalization. In Poland the supervision of safety product has been entrusted to the President of the Office of Competition and Consumer Protection. The agency supporting its activities is the Trade Inspection. Growing popularity of the quality systems conformable with the ISO 9000 standard caused that they have been included in the EU regulations as criteria of assessment of conformability with requirements. The certificate of the quality management system is indispensable for companies for functioning in many market areas. One should remember that quality management system will help the company to supervise unconformable products only when it really functions and is not just on paper. Only then it will function efficiently.

Comparison of Thromboemboli Prophylactic Effect of Aspirin and Low Dose Warfarin in Standard Risk Multiple Myeloma Patients that Treated with Regimens Containing Thalidomide

Directory of Open Access Journals (Sweden)

Seyed Amir Dadkhahi

2017-05-01

Full Text Available Abstract Background: Most of the current regimens in the treatment of multiple myeloma include thalidomide. Thalidomide is a modulator of the immune system and according to several studies, its main complication is thromboembolism. The aim of this study is to compare the thromboemboli prophylactic effect of aspirin and low dose warfarin in standard risk multiple myeloma patients that treated with regimens containing thalidomide. Materials and Methods: In this double- blind clinical trial study, sixty-six patients with multiple myeloma under treatment with thalidomide-containing regimens with standard risk for thromboembolism who were admitted to Khansari hospital, entered the study according to inclusion and exclusion criteria. The incidence of thromboembolism in these patients was evaluated. Results: Five patients in the warfarin group and 2 patients in the aspirin group had thromboemboli. Chi square analyses showed no significant difference between groups (p=0.635. Conclusion: The results showed that both drugs are effective in preventing thromboembolism and can be used as a prophylactic treatment.

76 FR 49365 - Cost Accounting Standards: Elimination of the Exemption From Cost Accounting Standards for...

Science.gov (United States)

2011-08-10

... Accounting Standards: Elimination of the Exemption From Cost Accounting Standards for Contracts and...: Office of Management and Budget (OMB), Office of Federal Procurement Policy (OFPP), Cost Accounting... Accounting Standards (CAS) Board, is publishing a final rule to eliminate the exemption from regulations...

Standardization of nuclear power plants in the United States: recent regulatory developments

International Nuclear Information System (INIS)

Cowan, B.Z.; Tourtellotte, J.R.

1992-01-01

On April 18, 1989, the United States (U.S.) Nuclear Regulatory Commission (NRC) amended the regulations governing the process for licensing nuclear power plants in the United States to provide for issuance of early site permits, standard design certifications and combined construction permits and operating licenses for nuclear power reactors. The new regulations are designed to achieve early resolution of licensing issues and facilitate standardization of nuclear power plants in the United States. The program for design standardization is central to efforts mounted by the U.S. government and industry to ensure that there will be a next generation of nuclear power facilities in the U.S. The most significant changes are provisions for certification of standard designs and for issuance prior to start of construction of combined licenses which incorporate a construction permit and an operating license with conditions. Such certifications and combined licenses must contain tests, inspections and analyses, and acceptance criteria, which are necessary and sufficient to provide reasonable assurance that the facility has been constructed and will operate in accordance with the combined license. A number of significant implementation issues have arisen. In addition a major court case brought by several anti-nuclear groups is pending, challenging NRC authority to issue combined licenses. It is the goal of the U.S. nuclear industry to have the first of the next generation of standardized nuclear power plants ordered, licensed, constructed and on-line by the year 2000. (author)

Effect of the proposed adoption of the International Atomic Energy Agency regulations, 1985 revision, on the U.S. radioactive waste transportation industry

International Nuclear Information System (INIS)

Benda, G.A.; Lewis, M.S.; Allen, J.H.

1989-01-01

The Nuclear Regulatory Commission (NRC) is proposing changes to 10CFR 71 transportation regulations to achieve compatibility with the 1985 IAEA regulations. The intent of these changes is to be more compatible with the international standard on shipping containers, package requirements, and performance criteria. The NRC has, however, modified part of its regulations to restrict the packaging of LSA by limiting the total activity rather than adopting the IAEA standard. This paper addresses how the proposed regulations will affect the low-level radioactive waste transportation industry. It describes the impacts on the transportation industry in three major areas-IAEA consistency, economic impact, and risk assessment. Available transport data from the Barnwell disposal site was used in the analysis of the proposed changes. The impacts addressed include possible increased radiation exposures, transportation risks and liability, transportation and processing costs, and waste disposal costs resulting in little health and safety benefit. Although the health and safety benefits of any change to the current regulations are minimal, suggested alternatives to the proposed regulations are discussed that more closely conform with the international standards while still maintaining health and safety

National Bureau of Standards health physics radioactive material shipment survey, packaging, and labelling program under ICAO/IATA and DOT regulations

International Nuclear Information System (INIS)

Sharp, D.R.; Slaback, L.A.

1984-01-01

NBS routinely ships many radionuclides in small to moderate activities, with many shipments containing mixtures of radionuclides in a variety of combinations. The ICAO/IATA shipping regulations (and the new DoT regulations on their model) specify individual shipping parameters for every radionuclide. As a result, quality control in the shipment of these radioactive packages has become difficult to maintain. The authors have developed a computer program that will guide a Health Physics technician through package surveys and give exact packaging and labelling instructions. The program is a 27 kilobyte user-friendly BASIC program that runs on an Epson-HX20 notebook computer with microcassette drive and 16 kilobyte memory expansion unit. This small computer is more manageable than the regulation books for which it will be substituted and will be used in routine radioactive shipments

7 CFR 160.32 - Marking containers.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Marking containers. 160.32 Section 160.32 Agriculture... STANDARDS FOR NAVAL STORES Analysis, Inspection, and Grading on Request § 160.32 Marking containers. The interested person shall provide any labor necessary for marking the containers, after the contents have been...

Regulating a Monopoly Offering Priority Service

OpenAIRE

Matsukawa, Isamu

2006-01-01

This paper investigates the effects of alternative forms of regulation on the market penetration and capacity, which are determined by a profit-maximizing monopolist providing priority service to consumers. For continuous priority service, a minimum reliability standard, price cap and rate of return regulation lead to larger capacity than in the absence of regulation. A minimum reliability standard reduces the market penetration while price cap and rate of return regulation increase it. T...

A conserved serine residue regulates the stability of Drosophila Salvador and human WW domain-containing adaptor 45 through proteasomal degradation

Energy Technology Data Exchange (ETDEWEB)

Wu, Di, E-mail: DiWu@mail.nankai.edu.cn; Wu, Shian

2013-04-19

Highlights: •Ser-17 is key for the stability of Drosophila Sav. •Ala mutation of Ser-17 promotes the proteasomal degradation of Sav. •Ser-17 residue is not the main target of Hpo-induced Sav stabilization. •Hpo-dependent and -independent mechanisms regulate Sav stability. •This mechanism is conserved in the homologue of Sav, human WW45. -- Abstract: The Hippo (Hpo) pathway is a conserved tumor suppressor pathway that controls organ size through the coordinated regulation of apoptosis and proliferation. Drosophila Salvador (Sav), which limits organ size, is a core component of the Hpo pathway. In this study, Ser-17 was shown to be important for the stability of Sav. Alanine mutation of Ser-17 promoted the proteasomal degradation of Sav. Destabilization and stabilization of the Sav protein mediated by alanine mutation of Ser-17 and by Hpo, respectively, were independent of each other. This implies that the stability of Sav is controlled by two mechanisms, one that is Ser-17-dependent and Hpo-independent, and another that is Ser-17-independent and Hpo-dependent. These dual mechanisms also regulated the human counterpart of Drosophila Sav, WW domain-containing adaptor 45 (WW45). The conservation of this regulation adds to its significance in normal physiology and tumorigenesis.

Human NACHT, LRR, and PYD domain-containing protein 3 (NLRP3) inflammasome activity is regulated by and potentially targetable through Bruton tyrosine kinase.

Science.gov (United States)

Liu, Xiao; Pichulik, Tica; Wolz, Olaf-Oliver; Dang, Truong-Minh; Stutz, Andrea; Dillen, Carly; Delmiro Garcia, Magno; Kraus, Helene; Dickhöfer, Sabine; Daiber, Ellen; Münzenmayer, Lisa; Wahl, Silke; Rieber, Nikolaus; Kümmerle-Deschner, Jasmin; Yazdi, Amir; Franz-Wachtel, Mirita; Macek, Boris; Radsak, Markus; Vogel, Sebastian; Schulte, Berit; Walz, Juliane Sarah; Hartl, Dominik; Latz, Eicke; Stilgenbauer, Stephan; Grimbacher, Bodo; Miller, Lloyd; Brunner, Cornelia; Wolz, Christiane; Weber, Alexander N R

2017-10-01

The Nod-like receptor NACHT, LRR, and PYD domain-containing protein 3 (NLRP3) and Bruton tyrosine kinase (BTK) are protagonists in innate and adaptive immunity, respectively. NLRP3 senses exogenous and endogenous insults, leading to inflammasome activation, which occurs spontaneously in patients with Muckle-Wells syndrome; BTK mutations cause the genetic immunodeficiency X-linked agammaglobulinemia (XLA). However, to date, few proteins that regulate NLRP3 inflammasome activity in human primary immune cells have been identified, and clinically promising pharmacologic targeting strategies remain elusive. We sought to identify novel regulators of the NLRP3 inflammasome in human cells with a view to exploring interference with inflammasome activity at the level of such regulators. After proteome-wide phosphoproteomics, the identified novel regulator BTK was studied in human and murine cells by using pharmacologic and genetic BTK ablation. Here we show that BTK is a critical regulator of NLRP3 inflammasome activation: pharmacologic (using the US Food and Drug Administration-approved inhibitor ibrutinib) and genetic (in patients with XLA and Btk knockout mice) BTK ablation in primary immune cells led to reduced IL-1β processing and secretion in response to nigericin and the Staphylococcus aureus toxin leukocidin AB (LukAB). BTK affected apoptosis-associated speck-like protein containing a CARD (ASC) speck formation and caspase-1 cleavage and interacted with NLRP3 and ASC. S aureus infection control in vivo and IL-1β release from cells of patients with Muckle-Wells syndrome were impaired by ibrutinib. Notably, IL-1β processing and release from immune cells isolated from patients with cancer receiving ibrutinib therapy were reduced. Our data suggest that XLA might result in part from genetic inflammasome deficiency and that NLRP3 inflammasome-linked inflammation could potentially be targeted pharmacologically through BTK. Copyright © 2017 American Academy of Allergy

Modelling air quality according to INSPIRE data specifications, ISO standards and national regulations

Directory of Open Access Journals (Sweden)

Pachelski Wojciech

2017-12-01

Full Text Available Protection of the environment is an activity of many institutions, organizations and communities from global to regional and local scales. Any activity in this area needs structured database records, using advanced methodology, given, among others, in INSPIRE documents, ISO standards of 19100 series, and national regulations. The goal of this paper is to analyse both the legal provisions related to the air quality and also data sources associated with the prevention of air pollution. Furthermore, the UML application schema of the spatial data related to the air protection is proposed, for the use by urban planners. Also, the overview of the methodology of geographic information is given, including the Unified Modelling Language (UML, as well as the basic concepts of conceptual models within the INSPIRE project. The study is based on the relevant literature and documents, as well as on the expert knowledge gained through urban planning practice, as well as on the analysis of the spatial planning regulations. The UML application schema for different aspects related to the air protection, as presented in this paper, is an example of how to use the methodology also in other fields of the environment protection. Spatial planners know how to improve the air quality, but in the present state of law they often suffer from the lack of planning tools for real actions. In the spatial planners work an important issue are data that allow a thorough analysis of the area.

78 FR 15883 - Standard Time Zone Boundaries

Science.gov (United States)

2013-03-13

...] RIN 2105-AE20 Standard Time Zone Boundaries AGENCY: Office of the Secretary (OST), Department of... time zone boundaries regulations to reflect changes that Congress made to the Uniform Time Act. The... regulations on standard time zone boundaries, 49 CFR Part 71, need to be updated in order to ensure their...

Simulation and analysis of the plutonium oxide/metal storage containers subject to various loading conditions

International Nuclear Information System (INIS)

Gong, C.; Miller, R.F.

1995-05-01

The structural and functional requirements of the Plutonium Oxide/Metal Storage Containers are specified in the Report ''Complex 21 Plutonium Storage Facility Material Containment Team Technical Data Report'' [Complex 21, 1993]. There are no existing storage containers designed for long term storage of plutonium and current codes, standards or regulations do not adequately cover this case. As there is no extensive experience with the long term (50+ years) storage of plutonium, the design of high integrity storage containers must address many technical considerations. This analysis discusses a few potential natural phenomena that could theoretically adversely affect the container integrity over time. The plutonium oxide/metal storage container consists of a primary containment vessel (the outer container), a bagless transfer can (the inner container), two vertical plates on top of the primary containment vessel, a circular plate (the flange) supported by the two plates, tube for gas sampling operations mounted at the center of the primary containment vessel top and a spring system being inserted in the cavity between the primary containment vessel and the cap of the bagless transfer can. The dimensions of the plutonium oxide/metal storage container assembly can be found in Figure 2-1. The primary container, the bagless transfer can, and all the attached components are made of Type 304L stainless steel

Liquidity regulation and bank behavior

OpenAIRE

Bonner, C.

2014-01-01

In response to the 2007-08 financial crisis, the Basel Committee on Banking Supervision proposed two liquidity standards to reinforce banks’ resilience to liquidity risks. The purpose of this thesis is to analyze the impact of liquidity regulation on bank behavior. The first of four main chapters analyzes the development of global liquidity standards, their objectives as well as their interaction with capital standards. The analysis suggests that regulating capital is associated with declinin...

Mouse ribosomal RNA genes contain multiple differentially regulated variants.

Directory of Open Access Journals (Sweden)

Hung Tseng

2008-03-01

Full Text Available Previous cytogenetic studies suggest that various rDNA chromosomal loci are not equally active in different cell types. Consistent with this variability, rDNA polymorphism is well documented in human and mouse. However, attempts to identify molecularly rDNA variant types, which are regulated individually (i.e., independent of other rDNA variants and tissue-specifically, have not been successful. We report here the molecular cloning and characterization of seven mouse rDNA variants (v-rDNA. The identification of these v-rDNAs was based on restriction fragment length polymorphisms (RFLPs, which are conserved among individuals and mouse strains. The total copy number of the identified variants is less than 100 and the copy number of each individual variant ranges from 4 to 15. Sequence analysis of the cloned v-rDNA identified variant-specific single nucleotide polymorphisms (SNPs in the transcribed region. These SNPs were used to develop a set of variant-specific PCR assays, which permitted analysis of the v-rDNAs' expression profiles in various tissues. These profiles show that three v-rDNAs are expressed in all tissues (constitutively active, two are expressed in some tissues (selectively active, and two are not expressed (silent. These expression profiles were observed in six individuals from three mouse strains, suggesting the pattern is not randomly determined. Thus, the mouse rDNA array likely consists of genetically distinct variants, and some are regulated tissue-specifically. Our results provide the first molecular evidence for cell-type-specific regulation of a subset of rDNA.

Transuranic contaminated waste container characterization and data base. Revision I

International Nuclear Information System (INIS)

Kniazewycz, B.G.

1980-05-01

The Nuclear Regulatory Commission (NRC) is developing regulations governing the management, handling and disposal of transuranium (TRU) radioisotope contaminated wastes as part of the NRC's overall waste management program. In the development of such regulations, numerous subtasks have been identified which require completion before meaningful regulations can be proposed, their impact evaluated and the regulations implemented. This report was prepared to assist in the development of the technical data base necessary to support rule-making actions dealing with TRU-contaminated wastes. An earlier report presented the waste sources, characteristics and inventory of both Department of Energy (DOE) generated and commercially generated TRU waste. In this report a wide variety of waste sources as well as a large TRU inventory were identified. The purpose of this report is to identify the different packaging systems used and proposed for TRU waste and to document their characteristics. This document then serves as part of the data base necessary to complete preparation and initiate implementation of TRU waste container and packaging standards and criteria suitable for inclusion in the present TRU waste management program. It is the purpose of this report to serve as a working document which will be used as appropriate in the TRU Waste Management Program. This report, and those following, will be compatible not only in format, but also in reference material and direction

Regulation of abiotic stress signalling by Arabidopsis C-terminal domain phosphatase-like 1 requires interaction with a k-homology domain-containing protein.

Directory of Open Access Journals (Sweden)

In Sil Jeong

Full Text Available Arabidopsis thaliana CARBOXYL-TERMINAL DOMAIN (CTD PHOSPHATASE-LIKE 1 (CPL1 regulates plant transcriptional responses to diverse stress signals. Unlike typical CTD phosphatases, CPL1 contains two double-stranded (ds RNA binding motifs (dsRBMs at its C-terminus. Some dsRBMs can bind to dsRNA and/or other proteins, but the function of the CPL1 dsRBMs has remained obscure. Here, we report identification of REGULATOR OF CBF GENE EXPRESSION 3 (RCF3 as a CPL1-interacting protein. RCF3 co-purified with tandem-affinity-tagged CPL1 from cultured Arabidopsis cells and contains multiple K-homology (KH domains, which were predicted to be important for binding to single-stranded DNA/RNA. Yeast two-hybrid, luciferase complementation imaging, and bimolecular fluorescence complementation analyses established that CPL1 and RCF3 strongly associate in vivo, an interaction mediated by the dsRBM1 of CPL1 and the KH3/KH4 domains of RCF3. Mapping of functional regions of CPL1 indicated that CPL1 in vivo function requires the dsRBM1, catalytic activity, and nuclear targeting of CPL1. Gene expression profiles of rcf3 and cpl1 mutants were similar during iron deficiency, but were distinct during the cold response. These results suggest that tethering CPL1 to RCF3 via dsRBM1 is part of the mechanism that confers specificity to CPL1-mediated transcriptional regulation.

Potential impacts of ICRP 60 and 61 on the transportation regulations

International Nuclear Information System (INIS)

Rawl, R.R.; Eckerman, K.F.; Wangler, M.E.; Punch, F.; Carriker, A.W.

1992-01-01

The International Commission on Radiation Protection (ICRP) has been providing recommendations for limitations on radiation exposure for decades. The ICRP recommendations address ionizing radiation and are concerned with protecting humans from its effects. These recommendations assist regulatory and advisory agencies in establishing and promulgating national regulations and practices in radiation Protection. Most countries have incorporated at least some aspect of the recommendations in their regulations since about 1956 when the first basic prowdon standard was Published in ICRP 2. Since that time ICRP has issued two major revisions to the recommendations. ICRP 26 was published in 1977 and ICRP 60 was published in 1991. These last two publications have companion works, ICRP 30 atid ICRP 61, that contain Annual Limits of Intake (ALI) for radiation workers. This report discusses the impacts of ICRP 60 and 61 on transport regulations

Development of fusion safety standards

International Nuclear Information System (INIS)

Longhurst, G.R.; Petti, D.A.; Dinneen, G.A.; Herring, J.S.; DeLooper, J.; Levine, J.D.; Gouge, M.J.

1996-01-01

Two new U.S. Department of Energy (DOE) standards have been prepared to assist in the design and regulation of magnetic fusion facilities. They are DOE-STD-6002-96, 'Safety of Magnetic Fusion Facilities - Requirements,' and DOE-STD-6003-96 'Safety of Magnetic Fusion Facilities - Guidance.' The first standard sets forth requirements, mostly based on the Code of Federal Regulations, deemed necessary for the safe design and operation of fusion facilities and a set of safety principles to use in the design. The second standard provides guidance on how to meet the requirements identified in DOE-STD-6002-96. It is written specifically for a facility such as the International Thermonuclear Experimental Reactor (ITER) in the DOE regulatory environment. As technical standards, they are applicable only to the extent that compliance with these standards is included in the contracts of the developers. 7 refs., 1 fig

CONVERGENCE OF INTERNATIONAL AUDIT STANDARDS AND AMERICAN AUDIT STANDARDS REGARDING SAMPLING

Directory of Open Access Journals (Sweden)

Chis Anca Oana

2013-07-01

Full Text Available Abstract: Sampling is widely used in market research, scientific analysis, market analysis, opinion polls and not least in the financial statement audit. We wonder what is actually sampling and how did it appear? Audit sampling involves the application of audit procedures to less than 100% of items within an account balance or class of transactions. Nowadays the technique is indispensable, the economic entities operating with sophisticated computer systems and large amounts of data. Economic globalization and complexity of capital markets has made possible not only the harmonization of international accounting standards with the national ones, but also the convergence of international accounting and auditing standards with the American regulations. International Standard on Auditing 530 and Statement on Auditing Standard 39 are the two main international and American normalized referentials referring to audit sampling. This article discusses the origin of audit sampling, mentioning a brief history of the method and different definitions from literature review. The two standards are studied using Jaccard indicators in terms of the degree of similarity and dissimilarity concerning different issues. The Jaccard coefficient measures the degree of convergence of international auditing standards (ISA 530 and U.S. auditing standards (SAS 39. International auditing standards and American auditing standards, study the sampling problem, both regulations presenting common points with regard to accepted sampling techniques, factors influencing the audit sample, treatment of identified misstatements and the circumstances in which sampling is appropriate. The study shows that both standards agree on application of statistical and non-statistical sampling in auditing, that sampling is appropriate for tests of details and controls, the factors affecting audit sampling being audit risk, audit objectives and population\\'s characteristics.

77 FR 51499 - Greenhouse Gas Emissions Standards and Fuel Efficiency Standards for Medium- and Heavy-Duty...

Science.gov (United States)

2012-08-24

... DEPARTMENT OF TRANSPORTATION National Highway Traffic Safety Administration 49 CFR Part 535 [NHTSA 2012-0126] RIN 2127-AK74 Greenhouse Gas Emissions Standards and Fuel Efficiency Standards for Medium... purpose of reducing greenhouse gas (GHG) emissions because the GHG standards fundamentally regulate fuel...

Standards of conduct for NASA employees

Science.gov (United States)

1987-01-01

'Standards of Conduct' for employees (14 CFR Part 1207) is set forth in this handbook and is hereby incorporated in the NASA Directives System. This handbook incorporates, for the convenience of NASA employees, the regulations now in effect prescribing standards of conduct for NASA employees. These regulations set forth the high ethical standards of conduct required of NASA employees in carrying out their duties and responsibilities. These regulations have been approved by the Office of Government Ethics, Office of Personnel Management. The regulations incorporated in this handbook were first published in the Federal Register on October 21, 1967 (32 FR 14648-14659); Part B concerning the acceptance of gifts, gratuities, or entertainment was extensively revised on January 19, 1976 (41 FR 2631-2633) to clarify and generally to restrict the exceptions to the general rule against the acceptance by a NASA employee from persons or firms doing or seeking business with NASA. Those regulations were updated on January 29, 1985 (50 FR 3887) to ensure conformity to the Ethics in Government Act of 1978 regarding the public financial disclosure statement. These regulations were published in the Federal Register on June 16, 1987 (52 FR 22755-764) and a correction was printed on Sept. 28, 1987 (52 FR 36234).

Standards development for the nuclear industry

International Nuclear Information System (INIS)

Domondon, D.B.

The ushering of nuclear era in the Philippines with the construction of the PNPP-I (Philippine Nuclear Power Plant) necessitates the evolvement and use of nuclear standards as a tool for safety evaluation in the licensing process. The Department of Nuclear Regulation and Safeguards under the Philippine Atomic Energy Commission has as one of its responsibilities the establishment of regulatory standards to ensure safe operation of nuclear facilities. This article points out the needs for nuclear standards and the steps in standard development which involve an enormous amount of resources in terms of manpower, expertise and money. The staff of the Department of Nuclear Regulations and Safeguards (DNRS) does not intend to engage in the original development of standards; rather, it reviews standards in use elsewhere, specifically in the U.S. and adopts to local conditions. (author)

Operator licensing examiner standards

International Nuclear Information System (INIS)

1987-05-01

The Operator Licensing Examiner Standards provide policy and guidance to NRC examiners and establish the procedures and practices for examining and licensing of applicants for NRC operator licenses pursuant to Part 55 of Title 10 of the Code of Federal Regulations (10 CFR 55). They are intended to assist NRC examiners and facility licensees to understand the examination process better and to provide for equitable and consistent administration of examinations to all applicants by NRC examiners. These standards are not a substitute for the operator licensing regulations and are subject to revision or other internal operator examination licensing policy changes

A Model of Yeast Cell-Cycle Regulation Based on a Standard Component Modeling Strategy for Protein Regulatory Networks.

Directory of Open Access Journals (Sweden)

Teeraphan Laomettachit

Full Text Available To understand the molecular mechanisms that regulate cell cycle progression in eukaryotes, a variety of mathematical modeling approaches have been employed, ranging from Boolean networks and differential equations to stochastic simulations. Each approach has its own characteristic strengths and weaknesses. In this paper, we propose a "standard component" modeling strategy that combines advantageous features of Boolean networks, differential equations and stochastic simulations in a framework that acknowledges the typical sorts of reactions found in protein regulatory networks. Applying this strategy to a comprehensive mechanism of the budding yeast cell cycle, we illustrate the potential value of standard component modeling. The deterministic version of our model reproduces the phenotypic properties of wild-type cells and of 125 mutant strains. The stochastic version of our model reproduces the cell-to-cell variability of wild-type cells and the partial viability of the CLB2-dbΔ clb5Δ mutant strain. Our simulations show that mathematical modeling with "standard components" can capture in quantitative detail many essential properties of cell cycle control in budding yeast.

Characterization of primary standards for use in the HPLC analysis of the procyanidin content of cocoa and chocolate containing products.

Science.gov (United States)

Hurst, William J; Stanley, Bruce; Glinski, Jan A; Davey, Matthew; Payne, Mark J; Stuart, David A

2009-10-15

This report describes the characterization of a series of commercially available procyanidin standards ranging from dimers DP = 2 to decamers DP = 10 for the determination of procyanidins from cocoa and chocolate. Using a combination of HPLC with fluorescence detection and MALDI-TOF mass spectrometry, the purity of each standard was determined and these data were used to determine relative response factors. These response factors were compared with other response factors obtained from published methods. Data comparing the procyanidin analysis of a commercially available US dark chocolate calculated using each of the calibration methods indicates divergent results and demonstrate that previous methods may significantly underreport the procyanidins in cocoa-containing products. These results have far reaching implications because the previous calibration methods have been used to develop data for a variety of scientific reports, including food databases and clinical studies.

Ethical standards and regulations principles of professional conduct in the field of mediation

Directory of Open Access Journals (Sweden)

Yulia I. Melnychuk

2016-01-01

Full Text Available An origin of conflicts, during life of man, is the inevitable phenomenon. A subject for a conflict results in the origin of conflict situation, which contains the negative colouring the display of which can be offence. Mediaciya appears the alternative method of permission of conflict, which is directed on zalagodzhennya and decision of conflicts by the direct socializing with an offender and suffering. A collaboration as a result of realization of which reasons of divergences and aspiration of resisting sides of search of vzaemopriynyatnikh ways of decision of situation turn out appears the base of process of mediacii. In this process the third participant is a neurohumor, the purpose of activity of which is adjusting and communicative process control. Institualizaciya of codes of conduct, which are added the certain types of moral mutual relations between people is optimum for realization of professional activity. Socialphilosophical interpretation of cultural, humanism principles of restoration process is fixed in the ethics standards of mediacii. Ethics norms are key in achievement of the real perfection, that is why there is a clear requirement in the ethics estimation of practice of neurohumor for the maintainance of moral, legal norms upgrading functioning. Professional practice of neurohumor is based on an awareness them of ethics aspects and social payment in prevention of recidivism, observance of ethics rules and standards, proper European legislation, national traditions.

Constructing regulation and regulating for energy efficient construction

Energy Technology Data Exchange (ETDEWEB)

Shove, Elizabeth [Lancaster University (United Kingdom). Centre for the Study of Environmental Change

1998-07-01

This project considers the process of formulating energy-related building regulation in the light of the revisions to Part L (Conservation of Fuel and Power) of the Building Regulations for England and Wales. Details are given of the main objectives of the research, namely, the examination of the roles of the UK government, local government and pressure groups in shaping energy efficiency standards, the impacts of environmental regulations, the limits of energy-related regulation, environmental regulation of the building sector, and the features of energy related building control. This control is compared with current practice in other European countries. The methodology of the project involving the review of governmental documents and interviews is described. (UK)

Material characteristics and construction methods for a typical research reactor concrete containment in Iran

International Nuclear Information System (INIS)

Ebrahimia, Mahsa; Suha, Kune Y.; Eghbalic, Rahman; Jahan, Farzaneh Asadi malek

2012-01-01

Generally selecting an appropriate material and also construction style for a concrete containment due to its function and special geometry play an important role in applicability and also construction cost and duration decrease in a research reactor (RR) project. The reactor containment enclosing the reactor vessel comprises physical barriers reflecting the safety design and construction codes, regulations and standards so as to prevent the community and the environment from uncontrolled release of radioactive materials. It is the third and the last barrier against radioactivity release. It protects the reactor vessel from such external events as earthquake and aircraft crash as well. Thus, it should be designed and constructed in such a manner as to withstand dead and live loads, ground and seismic loads, missiles and aircraft loads, and thermal and shrinkage loads. This study aims to present a construction method for concrete containment of a typical RR in Iran. The work also presents an acceptable characteristic for concrete and reinforcing re bar of a typical concrete containment. The current study has evaluated the various types of the RR containments. The most proper type was selected in accordance with the current knowledge and technology of Iran

Material characteristics and construction methods for a typical research reactor concrete containment in Iran

Energy Technology Data Exchange (ETDEWEB)

Ebrahimia, Mahsa; Suha, Kune Y. [Seoul National Univ., Seoul (Korea, Republic of); Eghbalic, Rahman; Jahan, Farzaneh Asadi malek [School of Architecture and Urbanism, Qazvin (Iran, Islamic Republic of)

2012-10-15

Generally selecting an appropriate material and also construction style for a concrete containment due to its function and special geometry play an important role in applicability and also construction cost and duration decrease in a research reactor (RR) project. The reactor containment enclosing the reactor vessel comprises physical barriers reflecting the safety design and construction codes, regulations and standards so as to prevent the community and the environment from uncontrolled release of radioactive materials. It is the third and the last barrier against radioactivity release. It protects the reactor vessel from such external events as earthquake and aircraft crash as well. Thus, it should be designed and constructed in such a manner as to withstand dead and live loads, ground and seismic loads, missiles and aircraft loads, and thermal and shrinkage loads. This study aims to present a construction method for concrete containment of a typical RR in Iran. The work also presents an acceptable characteristic for concrete and reinforcing re bar of a typical concrete containment. The current study has evaluated the various types of the RR containments. The most proper type was selected in accordance with the current knowledge and technology of Iran.

Development of a metallic high integrity container

International Nuclear Information System (INIS)

Haelsig, R.T.

1986-01-01

Nuclear Packaging, a Pacific Nuclear Company, developed a metallic high integrity container (HIC) for the burial of low level radioactive waste. This class of container has received the most extensive review of any burial container licensed in the United States. It is also the first container that has been licensed to meet the requirements of Nuclear Regulatory Commission Regulations 10CFR61. The design and subsequent review considered 300 years corrosion at a depth of 55 feet with no degradation of container structural integrity. The design also included a technical requirement that the container possess a positive vent that would exclude moisture. The alloy that was selected, allows for significant flexibility in container size and configuration which is essential to accommodating the various waste forms. This allowed the development of containers in various sizes and with a variety of closures, that accommodate the internal dimensions of various shipping shields and help minimize radiation exposure during packaging operations. The material used in the metallic container is high corrosion resistant which reduces the need for strict chemical controls at the waste generating facility. This acts to ease the operational requirements in the treatment of several waste streams. The design result is a family of metallic High Integrity Containers (HIC)s that meet all the performance criteria imposed by the regulations, as well as provide a disposable waste container with good transportation efficiency and minimum operational constraints

Developing standardized facility contingency plans

International Nuclear Information System (INIS)

Davidson, D.A.

1993-01-01

Texaco consists of several operating departments that are, in effect, independent companies. Each of these departments is responsible for complying with all environmental laws and regulations. This includes the preparation by each facility to respond to an oil spill at that location. For larger spills, however, management of the response will rest with corporate regional response teams. Personnel from all departments make up the regional teams. In 1990, Congress passed the Oil Pollution Act. In 1991, the US Coast Guard began developing oil spill response contingency plan regulations, which they are still working on. Meanwhile, four of the five west coast states have also passed laws requiring contingency plans. (Only Hawaii has chosen to wait and see what the federal regulations will entail). Three of the states have already adopted regulations. Given these laws and regulations, along with its corporate structure, Texaco addressed the need to standardize local facility plans as well as its response organization. This paper discusses how, by working together, the Texaco corporate international oil spill response staff and the Texaco western region on-scene commander developed: A standard contingency plan format crossing corporate boundaries and meeting federal and state requirements. A response organization applicable to any size facility or spill. A strategy to sell the standard contingency plan and response organization to the operating units

Dental Assisting Program Standards.

Science.gov (United States)

Georgia Univ., Athens. Dept. of Vocational Education.

This publication contains statewide standards for the dental assisting program in Georgia. The standards are divided into 12 categories: foundations (philosophy, purpose, goals, program objectives, availability, evaluation); admissions (admission requirements, provisional admission requirements, recruitment, evaluation and planning); program…

Food safety regulations in Australia and New Zealand Food Standards.

Science.gov (United States)

Ghosh, Dilip

2014-08-01

Citizens of Australia and New Zealand recognise that food security is a major global issue. Food security also affects Australia and New Zealand's status as premier food exporting nations and the health and wellbeing of the Australasian population. Australia is uniquely positioned to help build a resilient food value chain and support programs aimed at addressing existing and emerging food security challenges. The Australian food governance system is fragmented and less transparent, being largely in the hands of government and semi-governmental regulatory authorities. The high level of consumer trust in Australian food governance suggests that this may be habitual and taken for granted, arising from a lack of negative experiences of food safety. In New Zealand the Ministry of Primary Industries regulates food safety issues. To improve trade and food safety, New Zealand and Australia work together through Food Standards Australia New Zealand (FSANZ) and other co-operative agreements. Although the potential risks to the food supply are dynamic and constantly changing, the demand, requirement and supply for providing safe food remains firm. The Australasian food industry will need to continually develop its system that supports the food safety program with the help of scientific investigations that underpin the assurance of what is and is not safe. The incorporation of a comprehensive and validated food safety program is one of the total quality management systems that will ensure that all areas of potential problems are being addressed by industry. © 2014 Society of Chemical Industry.

Catalogue and classification of technical safety standards, rules and regulations for nuclear power reactors and nuclear fuel cycle facilities

International Nuclear Information System (INIS)

Fichtner, N.; Becker, K.; Bashir, M.

1977-01-01

The present report is an up-dated version of the report 'Catalogue and Classification of Technical Safety Rules for Light-water Reactors and Reprocessing Plants' edited under code No EUR 5362e, August 1975. Like the first version of the report, it constitutes a catalogue and classification of standards, rules and regulations on land-based nuclear power reactors and fuel cycle facilities. The reasons for the classification system used are given and discussed

7 CFR 160.73 - Availability of standards.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Availability of standards. 160.73 Section 160.73 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... STANDARDS FOR NAVAL STORES Loan and Care of United States Standards § 160.73 Availability of standards. (a...

7 CFR 160.46 - Identification of containers.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Identification of containers. 160.46 Section 160.46... STANDARDS FOR NAVAL STORES Request Inspection by Licensed Inspectors § 160.46 Identification of containers. Containers packed with naval stores which have been inspected, classified, graded, and certified by a...

40 CFR 59.103 - Container labeling requirements.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 5 2010-07-01 2010-07-01 false Container labeling requirements. 59.103... National Volatile Organic Compound Emission Standards for Automobile Refinish Coatings § 59.103 Container... automobile refinish coating or coating component container or package, the day, month, and year on which the...

40 CFR 59.405 - Container labeling requirements.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 5 2010-07-01 2010-07-01 false Container labeling requirements. 59.405... National Volatile Organic Compound Emission Standards for Architectural Coatings § 59.405 Container... section on the coating container in which the coating is sold or distributed. (1) The date the coating was...

21 CFR 1230.41 - Delivery of containers.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Delivery of containers. 1230.41 Section 1230.41 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) REGULATIONS UNDER CERTAIN OTHER ACTS ADMINISTERED BY THE FOOD AND DRUG ADMINISTRATION REGULATIONS UNDER THE...

Ocean Dumping Control Regulations

International Nuclear Information System (INIS)

1978-01-01

These Regulations were made further to the Ocean Dumping Control Act which provides for restrictions in dumping operations. The Regulations contain model applications for permits to dump or load a series of materials. (NEA)

Shielding standards: a case history

International Nuclear Information System (INIS)

Battat, M.E.

1977-01-01

A discussion of the sequence of events leading from the inception of a standard to its transmittal to the ANSI Board of Standards Review will be given. The standard referred to is entitled, ''Neutron and Gamma-Ray Flux-to-Dose-Rate Factors,'' (ANSI N666). Certain questions raised during the review process and the compatibility of this standard with the USA Code of Federal Regulations will be discussed

16 CFR 423.9 - Conflict with flammability standards.

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Conflict with flammability standards. 423.9... TEXTILE WEARING APPAREL AND CERTAIN PIECE GOODS AS AMENDED § 423.9 Conflict with flammability standards. If there is a conflict between this regulation and any regulations issued under the Flammable Fabrics...

7 CFR 201.36c - Hermetically-sealed containers.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Hermetically-sealed containers. 201.36c Section 201... ACT FEDERAL SEED ACT REGULATIONS Advertising § 201.36c Hermetically-sealed containers. The 5-month... been met: (a) The seed was packaged within 9 months after harvest; (b) The container used does not...

EM type radioactive standards. Radioaktivni etalony EM

Energy Technology Data Exchange (ETDEWEB)

1981-01-01

The standard contains technical specifications and conditions of production, testing, packing, transport and storage of EM type planar calibration standards containing radionuclides /sup 14/C, /sup 60/Co, /sup 90/Sr, /sup 137/Cs, /sup 147/Pm, /sup 204/Tl, /sup 239/Pu, /sup 241/Am and natural U. The terminology is explained, the related Czechoslovak standards and legal prescriptions given and amendments to these prescriptions presented.

TRUPACT-II container maintenance program plan

International Nuclear Information System (INIS)

1990-11-01

This document details the maintenance/repair and replacement of components, as well as the documentation required and the procedures to be followed to maintain the integrity of the TRUPACT-II container, in accordance with requirements of the TRUPACT-II Container Operations and Maintenance Manual, OM-134, the TRUPACT-II Container Safety Analysis Report (SARP), and the TRUPACT-II Container Certificate of Compliance (Number 9218). The routine shipping and receiving inspections required by the Department of Transportation (DOT), Department of Energy (DOE), Nuclear Regulatory Commission (NRC) and other regulations are not addressed in this document. This document applies to all DOE shipping and receiving sites that use the TRUPACT-II containers

Nonattainment of national ambient air quality standards: implications for energy policy

Energy Technology Data Exchange (ETDEWEB)

Garvey, D.B.; Streets, D.G.; Kotecki, R.; Senew, M.

1979-10-01

In accordance with the 1977 Clean Air Act Amendments, EPA established regulations governing new and existing sources of emissions in areas where the NAAQS are being exceeded. These requirements may constrain the implementation of a national energy policy to increase the use of coal in utilities and industries. The states designated the nonattainment areas and prepared State Implementation Plans, outlining strategies for attaining the standards by the deadline of December 31, 1982. This report contains maps of nonattainment areas for all pollutants and summaries of the attainment strategies for those pollutants most likely to affect fossil-fueled energy development - SO/sub 2/, TSP, and NO/sub x/. The review of SIPs indicates that attainment of SO/sub 2/ standards should be relatively easy. Attainment of TSP standards may be more difficult since point sources are already well controlled and further reductions in emissions will require controls on fugitive sources. NO/sub x/ nonattainment is currently limited to three small areas. The report also contains an examination of emission limitations in nonattainment areas and a national assessment of the potential constraints of nonattainment on energy development in 1985 to 1990. The assessment concludes that constraints on projected new coal-fired utilities should not be significant. Constraints on expanded industrial coal use from TSP nonattainment may be significant but the effects of SO/sub 2/ nonattainment should be limited.

Status of conversion of NE standards to national consensus standards

International Nuclear Information System (INIS)

Jennings, S.D.

1990-06-01

One major goal of the Nuclear Standards Program is to convert existing NE standards into national consensus standards (where possible). This means that an NE standard in the same subject area using the national consensus process. This report is a summary of the activities that have evolved to effect conversion of NE standards to national consensus standards, and the status of current conversion activities. In some cases, all requirements in an NE standard will not be incorporated into the published national consensus standard because these requirements may be considered too restrictive or too specific for broader application by the nuclear industry. If these requirements are considered necessary for nuclear reactor program applications, the program standard will be revised and issued as a supplement to the national consensus standard. The supplemental program standard will contain only those necessary requirements not reflected by the national consensus standard. Therefore, while complete conversion of program standards may not always be realized, the standards policy has been fully supported in attempting to make maximum use of the national consensus standard. 1 tab

48 CFR 30.101 - Cost Accounting Standards.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Cost Accounting Standards... CONTRACTING REQUIREMENTS COST ACCOUNTING STANDARDS ADMINISTRATION General 30.101 Cost Accounting Standards. (a... Accounting Standards (CAS) and to disclose in writing and follow consistently their cost accounting practices...

Underground storage tanks containing hazardous chemicals

International Nuclear Information System (INIS)

Wise, R.F.; Starr, J.W.; Maresca, J.W. Jr.; Hillger, R.W.; Tafuri, A.N.

1991-01-01

The regulations issued by the United States Environmental Protection Agency in 1988 require, with several exceptions, that underground storage tank systems containing petroleum fuels and hazardous chemicals be routinely tested for releases. This paper summarizes the release detection regulations for tank systems containing chemicals and gives a preliminary assessment of the approaches to release detection currently being used. To make this assessment, detailed discussions were conducted with providers and manufacturers of leak detection equipment and testing services, owners or operators of different types of chemical storage tank systems, and state and local regulators. While these discussions were limited to a small percentage of each type of organization, certain observations are sufficiently distinctive and important that they are reported for further investigation and evaluation. To make it clearer why certain approaches are being used, this paper also summarizes the types of chemicals being stored, the effectiveness of several leak detection testing systems, and the number and characteristics of the tank systems being used to store these products

Transports of radioactive materials. Legal regulations, safety and security concepts, experience; Befoerderung radioaktiver Stoffe. Rechtsvorschriften, Sicherheits- und Sicherungskonzept, Erfahrungen

Energy Technology Data Exchange (ETDEWEB)

Schwarz, Guenther

2012-07-15

In Germany, approximately 650,000 to 750,000 units containing radioactive materials for scientific, medical and technical applications are shipped annually by surface, air and water transports. Legally speaking, radioactive materials are dangerous goods which can cause hazards to life, health, property and the environment as a result of faulty handling or accidents in transit. For protection against these hazards, their shipment therefore is regulated in extensive national and international rules of protection and safety. The article contains a topical review of the international and national transport regulations and codes pertaining to shipments of radioactive materials, and of the protection concepts underlying these codes so as to ensure an adequate standard of safety and security in shipping radioactive materials in national and international goods traffic. (orig.)

Working out the standards for nuclear power aging management implementation (PLM Standards)

International Nuclear Information System (INIS)

Miyano, Hiroshi

2008-01-01

Background of preparation of standards, preparation of standards for development of nuclear power aging management technologies, revision of PLM (Product Lifecycle Management) standards, and problems of PLM standards are stated. The placement of social needs, scheme, the standards system, preparation of rules and standards, and practical use of them by road map are illustrated and explained. Relation between the safety regulations and examination standards, and development and preparation of standards system are outlined. The nuclear power plant aging management and the maintenance control are provided by many rules and standards. PLM standards defines the aging phenomena and extracts the measurements and reflects them on the usual maintenance flow under the long term maintenance program. New examination system constructs the usual maintenance and the maintenance based on the aging management and long term maintenance program. Outline and construction of PLM standards are explained with notes and additional books. (S.Y.)

Hazardous materials package performance regulations

International Nuclear Information System (INIS)

Russell, N.A.; Glass, R.E.; McClure, J.D.; Finley, N.C.

1992-01-01

The hazardous materials (hazmat) packaging development and certification process is currently defined by two different regulatory philosophies, one based on specification packagings and the other based on performance standards. With specification packagings, a packaging is constructed according to an agreed set of design specifications. In contrast, performance standards do not specify the packaging design; they specify performance standards that a packaging design must be able to pass before it can be certified for transport. The packaging can be designed according to individual needs as long as it meets these performance standards. Performance standards have been used nationally and internationally for about 40 years to certify radioactive materials (RAM) packagings. It is reasonable to state that for RAM transport, performance specifications have maintained transport safety. A committee of United Nation's experts recommended the performance standard philosophy as the preferred regulation method for hazmat packaging. Performance standards for hazmat packagings smaller than 118 gallons have been adopted in 49CFR178. Packagings for materials that are classified as toxic-by-inhalation must comply with the performance standards by October 1, 1993, and packagings for all other classes of hazardous materials covered must comply by October 1, 1996. For packages containing bulk (in excess of 188 gallons) quantities of materials that are extremely toxic by inhalation, there currently are no performance requirements. This paper discusses a Hazmat Packaging Performance Evaluation (HPPE) project to look at the subset of bulk packagings that are larger than 2000 gallons. The objectives of this project are the evaluate current hazmat specification packagings and develop supporting documentation for determining performance requirements for packagings in excess of 2000 gallons that transport hazardous materials that have been classified as extremely toxic by inhalation (METBI)

7 CFR 160.29 - Containers to remain intact.

Science.gov (United States)

2010-01-01

... Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) NAVAL STORES REGULATIONS AND.... The results of any analysis, classification, or grading of naval stores will be certifiable only if...

Is ionizing radiation regulated more stringently than chemical carcinogens

International Nuclear Information System (INIS)

Travis, C.C.; Pack, S.R.; Hattemer-Frey, H.A.

1989-01-01

It is widely believed that United States government agencies regulate exposure to ionizing radiation more stringently than exposure to chemical carcinogens. It is difficult to verify this perception, however, because chemical carcinogens and ionizing radiation are regulated using vastly different strategies. Chemical carcinogens are generally regulated individually. Regulators consider the risk of exposure to one chemical rather than the cumulative radiation exposure from all sources. Moreover, standards for chemical carcinogens are generally set in terms of quantities released or resultant environmental concentrations, while standards for ionizing radiation are set in terms of dose to the human body. Since chemicals and ionizing radiation cannot be compared on the basis of equal dose to the exposed individual, standards regulating chemicals and ionizing radiation cannot be compared directly. It is feasible, however, to compare the two sets of standards on the basis of equal risk to the exposed individual, assuming that standards for chemicals and ionizing radiation are equivalent if estimated risk levels are equitable. This paper compares risk levels associated with current standards for ionizing radiation and chemical carcinogens. The authors do not attempt to determine whether either type of risk is regulated too stringently or not stringently enough but endeavor only to ascertain if ionizing radiation is actually regulated more strictly than chemical carcinogens

TRUPACT-II Container Maintenance Program Plan

International Nuclear Information System (INIS)

1991-05-01

This document details the maintenance, repair, and replacement of components, as well as the documentation required and the procedures to be followed to maintain the integrity of the TRUPACT-II container in accordance with OM-134, TRUPACT-II Container Operations and Maintenance Manual; and the TRUPACT-II Container Certificate of Compliance (Number 9218). The routine shipping and receiving inspections required by the Department of Transportation (DOT), Department of Energy (DOE), Nuclear Regulatory Commission (NRC) and other regulations are not addressed in this document. This document applies to all DOE shipping and receiving sites that use the TRUPACT-II containers

GTA Welding Research and Development for Plutonium Containment

International Nuclear Information System (INIS)

Sessions, C.E.

2002-01-01

This paper discusses the development of two welding systems that are used to contain actinide metals and oxides for long term storage. The systems are termed the bagless transfer system (BTS) and the outer container welder (OCW) system. The BTS is so named because it permits the containment of actinides without a polymeric package (i.e., bag). The development of these two systems was directed by Department of Energy Standard 3013, hereafter referred to as DOE 3013. This document defines the product and container requirements. In addition, it references national codes and standards for leak rates, ANSI N14.5, and design, American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code Section VIII (BandPVC)

Comparison of some European regulations

Energy Technology Data Exchange (ETDEWEB)

Argyriadis, K [Germanisher Lloyd, Hamburg (Germany)

1996-09-01

Fatigue calculations are an essential part in certification of a wind turbine. Manufacturers have to fulfill recommendations of several different regulations throughout Europe with the result that the design has often to be altered to satisfy them. In general three national (D/GL, NL, DK), and two international (GL, IEC) regulations are in use, with the IEC standard getting more importance with wind energy deploying to more in regions with no yet clearly defined national standards (India, Spain). The Germanischer Lloyd made calculations for wind turbines they are certifying and in one case we compared the resulting damages for different regulations and classes on a 600 kW, three bladed, stall regulated wind turbine. (EG) 18 refs.

Residual Stress Testing of Outer 3013 Containers

International Nuclear Information System (INIS)

Dunn, K.

2004-01-01

A Gas Tungsten Arc Welded (GTAW) outer 3013 container and a laser welded outer 3013 container have been tested for residual stresses according to the American Society for Testing Materials (ASTM) Standard G-36-94 [1]. This ASTM standard describes a procedure for conducting stress-corrosion cracking tests in boiling magnesium chloride (MgCl2) solution. Container sections in both the as-fabricated condition as well as the closure welded condition were evaluated. Significantly large residual stresses were observed in the bottom half of the as-fabricated container, a result of the base to can fabrication weld because through wall cracks were observed perpendicular to the weld. This observation indicates that regardless of the closure weld technique, sufficient residual stresses exist in the as-fabricated container to provide the stress necessary for stress corrosion cracking of the container, at the base fabrication weld. Additionally, sufficiently high residual stresses were observed in both the lid and the body of the GTAW as well as the laser closure welded containers. The stresses are oriented perpendicular to the closure weld in both the container lid and the container body. Although the boiling MgCl2 test is not a quantitative test, a comparison of the test results from the closure welds shows that there are noticeably more through wall cracks in the laser closure welded container than in the GTAW closure welded container

48 CFR 3003.101 - Standards of conduct.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 7 2010-10-01 2010-10-01 false Standards of conduct. 3003.101 Section 3003.101 Federal Acquisition Regulations System DEPARTMENT OF HOMELAND SECURITY, HOMELAND SECURITY ACQUISITION REGULATION (HSAR) GENERAL IMPROPER BUSINESS PRACTICES AND PERSONAL CONFLICTS OF...

Measurements and assessments on shielding performance of FCTC{sub 10}'6{sup 0}Co transport container

Energy Technology Data Exchange (ETDEWEB)

Zhuang, Dajie; Li, Guo Qiang; Wang, Renze [China Institute for Radiation Protection, Shanxi (China); Zhang, Guo Qing [Shanghai Institute of Applied Physics, Shanghai (China)

2016-09-15

FCTC10 container is designed to transport {sup 60}Co radioactive sources used in irradiation industry. It belongs to Type B(U) Category III (yellow) package when being loaded with a {sup 60}Co source of 1.8×10{sup 5} Ci. The container is constituted of shielding container, basket, protective cover and bracket. Shielding ability is provided mainly by stainless steel shells, tungsten alloy and lead among steel shells. Radiation level around the container has been calculated with both Monte Carlo simulations and measurements. It is proven that the shielding performance of the container fulfills the requirements in GB11806-2004 (Regulations for the safe transport of radioactive material, China Standard Press). Exposure doses to workers and to critical groups of public were calculated based on hypothetical exposure scene according to transport practice experience. The results show that doses to workers and public are less than the constraint dose considered in design, and the radiation level would be increased less than a factor of 2 under design basis accidents.

Cement: Administrative tender specifications and standards in Spain

OpenAIRE

Soria Santamaría, Francisco

1991-01-01

The paper describes, in chronological order, the different competent Authorities in Spain and the documents issued by them regarding Cement Regulations and Standards. The origin of the early cement quality Rules is referred to, the issuing of Regulations by the Public Bodies and finally the adoption of National Standards on the one hand, as well as the first initiatives to establish International Standards, especially motivated by the export boom after the Second World War, on the other. ...

Current situation on regulations for mycotoxins. Overview of tolerances and status of standard methods of sampling and analysis.

Science.gov (United States)

Van Egmond, H P

1989-01-01

A worldwide enquiry was undertaken in 1986-1987 to obtain up-to-date information about mycotoxin legislation in as many countries of the world as possible. Together with some additional data collected in 1981, information is now available about planned, proposed, existing or absence of legislation in 66 countries. Details about tolerances, legal bases, responsible authorities, prescribed methods of sampling and analysis and disposition of commodities containing inadmissible amounts of mycotoxins, are given. The information concerns aflatoxins in foodstuffs, aflatoxin M1 in dairy products, aflatoxins in animal feedstuffs, and other mycotoxins in food- and feedstuffs. In comparison with the situation in 1981, limits and regulations for mycotoxins have been expanded in 1987 with more countries having legislation (proposed or passed) on the subject, more products, and more mycotoxins covered by this legislation. The differences between tolerances in the various countries are sometimes quite large, which makes harmonization of mycotoxin regulations highly desirable.

Safety Regulations for Ionizing Radiations. Vietnam Standard (TCVN 4397-87)

International Nuclear Information System (INIS)

1987-01-01

The regulations were prepared for purpose of providing basic requirements of ionizing radiation protection and giving guide for design criteria of radiation installations in Vietnam. The allowable maximum levels for personnel categories are established. Regulated are methods for handling sealed and unsealed sources of radiation, transfer and transport of radioactive materials. Defined requirements and operating conditions that must be met. Determined are procedures and actions of decontamination. (N.H.A)

EU Regulation of Nanobiocides: Challenges in Implementing the Biocidal Product Regulation (BPR)

DEFF Research Database (Denmark)

Brinch, Anna; Hansen, Steffen Foss; Hartmann, Nanna B.

2016-01-01

The Biocidal Products Regulation (BPR) contains several provisions for nanomaterials (NMs) and is the first regulation in the European Union to require specific testing and risk assessment for the NM form of a biocidal substance as a part of the information requirements. Ecotoxicological data...

The industry commitment to global transport safety standards

International Nuclear Information System (INIS)

Green, L.

2004-01-01

Standards and regulations have no intrinsic practical effect without taking into account those who are the object of such standards and regulations. Standards and regulations do not become operationally effective until they are implemented by the entities which are subject to them. Accordingly, there is a necessary synergy between the regulator and the regulated - the regulators whose task it is to make and enforce the rules for safe, efficient and reliable transport, and those whose job it is to transport within the rules. One has no full meaning without the other. Harmonisation issues which can impede efficient and timely implementation of regulations can occur at any stage of the process, starting with the timely publication of the IAEA Regulations, incorporation by the modal organisations, adoption by national competent authorities and finally, rendered operational by industrial transport organisations. Both, the regulator and the transporter, can be more effective in achieving their purposes when they co-operate in the interest of mutual understanding. PATRAM provides one excellent opportunity for such exchange between the regulator and the regulated - there are other important opportunities within the IAEA and international modal organisations. I suggest, however, that more could be done between the regulators and the regulated collectively to share real-life experiences with actually implementing the regulations and operating within them, and to draw appropriate lessons. In the case of the international transport safety regulatory regime, it is the nuclear transport industry, such as represented by the World Nuclear Transport Institute (WNTI), which is, of course, the object of transport safety standards and regulations. And as such, the nuclear transport industry is a principal stakeholder in the regime. Regulatory compliance is a cornerstone of the nuclear transport industry. The international nature of the fuel cycle mandates transnational movement of

The industry commitment to global transport safety standards

International Nuclear Information System (INIS)

Green, L.

2004-01-01

Standards and regulations have no intrinsic practical effect without taking into account those who are the object of such standards and regulations. Standards and regulations do not become operationally effective until they are implemented by the entities which are subject to them. Accordingly, there is a necessary synergy between the regulator and the regulated-the regulators whose task it is to make and enforce the rules for safe, efficient and reliable transport, and those whose job it is to transport within the rules. One has no full meaning without the other. Harmonisation issues which can impede efficient and timely implementation of regulations can occur at any stage of the process, starting with the timely publication of the IAEA regulations, incorporation by the modal organisations, adoption by national competent authorities and finally, rendered operational by industrial transport organisations. Both the regulator and the transporter can be more effective in achieving their purposes when they cooperate in the interest of mutual understanding. PATRAM provides one excellent opportunity for such exchange between the regulator and the regulated-there are other important opportunities within the IAEA and international modal organisations. It is suggested, however, that more could be done between the regulators and the regulated collectively to share real-life experiences with actually implementing the regulations and operating within them, and to draw appropriate lessons. In the case of the international transport safety regulatory regime, it is the nuclear transport industry, such as represented by the World Nuclear Transport Institute (WNTI), which is, of course, the object of transport safety standards and regulations. And as such, the nuclear transport industry is a principal stakeholder in the regime. Regulatory compliance is a cornerstone of the nuclear transport industry. The international nature of the fuel cycle mandates transnational movement of

The industry commitment to global transport safety standards

Energy Technology Data Exchange (ETDEWEB)

Green, L. [World Nuclear Transport Inst., London (United Kingdom)

2004-07-01

Standards and regulations have no intrinsic practical effect without taking into account those who are the object of such standards and regulations. Standards and regulations do not become operationally effective until they are implemented by the entities which are subject to them. Accordingly, there is a necessary synergy between the regulator and the regulated - the regulators whose task it is to make and enforce the rules for safe, efficient and reliable transport, and those whose job it is to transport within the rules. One has no full meaning without the other. Harmonisation issues which can impede efficient and timely implementation of regulations can occur at any stage of the process, starting with the timely publication of the IAEA Regulations, incorporation by the modal organisations, adoption by national competent authorities and finally, rendered operational by industrial transport organisations. Both, the regulator and the transporter, can be more effective in achieving their purposes when they co-operate in the interest of mutual understanding. PATRAM provides one excellent opportunity for such exchange between the regulator and the regulated - there are other important opportunities within the IAEA and international modal organisations. I suggest, however, that more could be done between the regulators and the regulated collectively to share real-life experiences with actually implementing the regulations and operating within them, and to draw appropriate lessons. In the case of the international transport safety regulatory regime, it is the nuclear transport industry, such as represented by the World Nuclear Transport Institute (WNTI), which is, of course, the object of transport safety standards and regulations. And as such, the nuclear transport industry is a principal stakeholder in the regime. Regulatory compliance is a cornerstone of the nuclear transport industry. The international nature of the fuel cycle mandates transnational movement of

Positioning of AMPA Receptor-Containing Endosomes Regulates Synapse Architecture

Directory of Open Access Journals (Sweden)

Marta Esteves da Silva

2015-11-01

Full Text Available Lateral diffusion in the membrane and endosomal trafficking both contribute to the addition and removal of AMPA receptors (AMPARs at postsynaptic sites. However, the spatial coordination between these mechanisms has remained unclear, because little is known about the dynamics of AMPAR-containing endosomes. In addition, how the positioning of AMPAR-containing endosomes affects synapse organization and functioning has never been directly explored. Here, we used live-cell imaging in hippocampal neuron cultures to show that intracellular AMPARs are transported in Rab11-positive recycling endosomes, which frequently enter dendritic spines and depend on the microtubule and actin cytoskeleton. By using chemically induced dimerization systems to recruit kinesin (KIF1C or myosin (MyosinV/VI motors to Rab11-positive recycling endosomes, we controlled their trafficking and found that induced removal of recycling endosomes from spines decreases surface AMPAR expression and PSD-95 clusters at synapses. Our data suggest a mechanistic link between endosome positioning and postsynaptic structure and composition.

An Evaluation of the Self-Regulation of Promotional Competitions in South Africa

Directory of Open Access Journals (Sweden)

Daniel Strachan

2016-06-01

Full Text Available Promotional competitions are competitions in which prizes are awarded by lot or chance in order to promote goods or services. In order to protect participants and consumers against abuse, these competitions are usually regulated by gambling or consumer protection legislation. However, the relevant legislation is often complemented by self-regulation, which is the focus of this contribution. Self-regulation entails the regulation or governing of an industry by the role players in that industry. This article commences by explaining the relevant terminology and exploring self-regulation in general, including the various forms of self-regulation and the binding force thereof. The nature of self-regulation is discussed together with the advantages and challenges associated with this form of regulation. This is followed by some examples of self-regulation on a global level in order to provide a comparative perspective on the topic. The provisions of the International Chamber of Commerce's Consolidated Code of Advertising and Marketing Communications Practice are summarised and the European Advertising Standards Alliance's role in self-regulation is considered. Attention is also given to the relevant industry codes in the United Kingdom in view of the comprehensive way in which promotional competitions are covered by self-regulation in that country. The main part of the article centres on the self-regulatory position in South Africa. A brief overview of the role and function of the Advertising Standards Authority of South Africa (ASASA is provided. The provisions of the ASASA's Code of Advertising Practice are then examined and some ASASA rulings are discussed in order to illustrate the relevant principles. Thereafter, the focus shifts to the Code of Conduct of the Wireless Application Service Providers' Association, which contains detailed provisions relating to promotional competitions. Some relevant rulings are also considered. In conclusion

Confirmation tests of PWR surveillance capsule shipping container

International Nuclear Information System (INIS)

Tomita, N.; Ue, K.; Ohashi, M.; Asada, K.; Yoneda, Y.

1980-01-01

Mitsubishi Heavy Industries, Ltd. carried out the confirmation tests to confirm the reliability of the PWR surveillance capsule shipping container and to collect cask design data using a 10-ton weight full scale model at Kobe Shipyard and Engine Works. This report presents the outline of these tests. The B Type container was a cylinder 3289 mm long, 1080 mm in diameter and designed in accordance with the new modified Japanese regulations similar to IAEA regulation. These tests consist of four 9 m drop tests, two 1 m puncture tests, a fire test and an immersion test. In conclusion, safetyness of this container has been proved and various technical data for cask design were also collected through these tests. (author)

Overview of Development and Deployment of Codes, Standards and Regulations Affecting Energy Storage System Safety in the United States

Energy Technology Data Exchange (ETDEWEB)

Conover, David R.

2014-08-22

This report acquaints stakeholders and interested parties involved in the development and/or deployment of energy storage systems (ESS) with the subject of safety-related codes, standards and regulations (CSRs). It is hoped that users of this document gain a more in depth and uniform understanding of safety-related CSR development and deployment that can foster improved communications among all ESS stakeholders and the collaboration needed to realize more timely acceptance and approval of safe ESS technology through appropriate CSR.

Experience with the 1985 UK ionizing radiation regulations: the regulators' viewpoint

International Nuclear Information System (INIS)

Bines, W.P.; Beaver, P.F.

1991-01-01

The Ionising Radiations Regulations 1985 achieved UK implementation of the Euratom Basic Safety Standards Directive; interim action has taken account of recent revisions of risk estimates and the regulations will not be revised in advance of renegotiation of the Euratom Directive. Wide ranging consultation, central to the development of health and safety legislation in the UK, leads to greater co-operation between regulators and regulated and more acceptable legislation. Examples of co-operation, also of methods of enforcement and the use made of them, are given. The authors conclude that the regulations have stood the test of experience well. (Author)

75 FR 79803 - Semiannual Agenda of Regulations

Science.gov (United States)

2010-12-20

... some kinds of flavorings, foods, and beverages. They have begun to use substitutes such as 2,3..., Secretary of Labor. Office of Labor-Management Standards--Proposed Rule Stage Regulation Sequence Title... issue of the Federal Register. Office of Labor-Management Standards--Completed Actions Regulation...

NucleDyne's passive containment system

International Nuclear Information System (INIS)

Falls, O.B. Jr.; Kleimola, F.W.

1987-01-01

A simple definition of the passive containment system is that it is a total safeguards system for light water reactors designed to prevent and contain any accidental release of radioactivity. Its passive features utilize the natural laws of physics and thermodynamics. The system encompasses three basic containments constructed as one integrated structure on the reactor building foundation. The primary containment encloses the reactor pressure vessel and coolant system and passive engineered safety systems and components. Auxiliary containment enclosures house auxiliary systems and components. Secondary containment (the reactor building), housing the primary and auxiliary containment structures, provides a second containment barrier as added defense-in-depth against leakage of radioactivity for all accidents assumed by the industry. The generic features of the passive containment system are applicable to both the boiling water reactors and the pressurized water reactors as standardized features for all power ranges. These features provide for a zero source term, the industry's ultimate safety goal. This paper relates to a four-loop pressurized water reactor

Epidermal growth factor-containing fibulin-like extracellular matrix protein 1 expression and regulation in uterine leiomyoma.

Science.gov (United States)

Marsh, Erica E; Chibber, Shani; Wu, Ju; Siegersma, Kendra; Kim, Julie; Bulun, Serdar

2016-04-01

To determine the presence, differential expression, and regulation of epidermal growth factor-containing fibulin-like extracellular matrix protein 1 (EFEMP1) in uterine leiomyomas. Laboratory in vivo and in vitro study with the use of human leiomyoma and myometrial tissue and primary cells. Academic medical center. Leiomyoma and myometrial tissue samples and cultured cells. 5-Aza-2'-deoxycytidine (5-aza-dC) treatment. Fold-change difference between EFEMP1 and fibulin-3 expression in leiomyoma tissue and cells compared with matched myometrial samples, and fold-change difference in EFEMP1 expression with 5-Aza-dC treatment. In vivo, EFEMP1 expression was 3.19-fold higher in myometrial tissue than in leiomyoma tissue. EFEMP1 expression in vitro was 5.03-fold higher in myometrial cells than in leiomyoma cells. Western blot and immunohistochemistry staining of tissue and cells confirmed similar findings in protein expression. Treatment of leiomyoma cells with 5-Aza-dC resulted in increased expression of EFEMP1 in vitro. The EFEMP1 gene and its protein product, fibulin-3, are both significantly down-regulated in leiomyoma compared with myometrium when studied both in vivo and in vitro. The increase in EFEMP1 expression in leiomyoma cells with 5-Aza-dC treatment suggest that differential methylation is responsible, in part, for the differences seen in gene expression. Copyright © 2016 American Society for Reproductive Medicine. Published by Elsevier Inc. All rights reserved.

40 CFR 403.6 - National pretreatment standards: Categorical standards.

Science.gov (United States)

2010-07-01

... falls within that particular subcategory. If an existing Industrial User adds or changes a process or... best of my knowledge and belief, true, accurate, and complete. I am aware that there are significant... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GENERAL PRE-TREAT-MENT REGULATIONS FOR EXIST-ING AND NEW...

State Standards and State Assessment Systems: A Guide to Alignment. Series on Standards and Assessments.

Science.gov (United States)

La Marca, Paul M.; Redfield, Doris; Winter, Phoebe C.

Alignment of content standards, performance standards, and assessments is crucial. This guide contains information to assist states and districts in aligning their assessment systems to their content and performance standards. It includes a review of current literature, both published and fugitive. The research is woven together with a few basic…

System certification progress in concept recognition in IAEA regulation

International Nuclear Information System (INIS)

Luna, R.E.; Pollog, T.

1995-01-01

System Certification is a regulatory concept which is intended to expand the scope of radioactive material transport regulations by allowing alternative means for proving compliance with the requisite standards of safety set out in transport regulations. In practice it may allow more stringent requirements in one aspect of the regulations to be substituted for less stringent application in other areas so long as the safety standard provided by regulation is preserved. The concept is widely perceived as the imposition of operational controls in exchange for relaxation of packaging standards, but that is only one possibility in the spectrum of potential actions under a System Certification provision in IAEA or national regulations

NASA software documentation standard software engineering program

Science.gov (United States)

1991-01-01

The NASA Software Documentation Standard (hereinafter referred to as Standard) can be applied to the documentation of all NASA software. This Standard is limited to documentation format and content requirements. It does not mandate specific management, engineering, or assurance standards or techniques. This Standard defines the format and content of documentation for software acquisition, development, and sustaining engineering. Format requirements address where information shall be recorded and content requirements address what information shall be recorded. This Standard provides a framework to allow consistency of documentation across NASA and visibility into the completeness of project documentation. This basic framework consists of four major sections (or volumes). The Management Plan contains all planning and business aspects of a software project, including engineering and assurance planning. The Product Specification contains all technical engineering information, including software requirements and design. The Assurance and Test Procedures contains all technical assurance information, including Test, Quality Assurance (QA), and Verification and Validation (V&V). The Management, Engineering, and Assurance Reports is the library and/or listing of all project reports.

Status of conversion of DOE standards to non-Government standards

Energy Technology Data Exchange (ETDEWEB)

Moseley, H.L.

1992-07-01

One major goal of the DOE Technical Standards Program is to convert existing DOE standards into non-Government standards (NGS's) where possible. This means that a DOE standard may form the basis for a standards-writing committee to produce a standard in the same subject area using the non-Government standards consensus process. This report is a summary of the activities that have evolved to effect conversion of DOE standards to NGSs, and the status of current conversion activities. In some cases, all requirements in a DOE standard will not be incorporated into the published non-Government standard because these requirements may be considered too restrictive or too specific for broader application by private industry. If requirements in a DOE standard are not incorporated in a non-Government standard and the requirements are considered necessary for DOE program applications, the DOE standard will be revised and issued as a supplement to the non-Government standard. The DOE standard will contain only those necessary requirements not reflected by the non-Government standard. Therefore, while complete conversion of DOE standards may not always be realized, the Department's technical standards policy as stated in Order 1300.2A has been fully supported in attempting to make maximum use of the non-Government standard.

Status of conversion of DOE standards to non-Government standards

Energy Technology Data Exchange (ETDEWEB)

Moseley, H.L.

1992-07-01

One major goal of the DOE Technical Standards Program is to convert existing DOE standards into non-Government standards (NGS`s) where possible. This means that a DOE standard may form the basis for a standards-writing committee to produce a standard in the same subject area using the non-Government standards consensus process. This report is a summary of the activities that have evolved to effect conversion of DOE standards to NGSs, and the status of current conversion activities. In some cases, all requirements in a DOE standard will not be incorporated into the published non-Government standard because these requirements may be considered too restrictive or too specific for broader application by private industry. If requirements in a DOE standard are not incorporated in a non-Government standard and the requirements are considered necessary for DOE program applications, the DOE standard will be revised and issued as a supplement to the non-Government standard. The DOE standard will contain only those necessary requirements not reflected by the non-Government standard. Therefore, while complete conversion of DOE standards may not always be realized, the Department`s technical standards policy as stated in Order 1300.2A has been fully supported in attempting to make maximum use of the non-Government standard.

Trends in U.S. nuclear standards development

International Nuclear Information System (INIS)

Crowley, J.H.; Kaminski, R.S.

1987-01-01

Regulation of the U.S Nuclear Power industry has been extensive during the 1970's. Key to this situation has been the evolution in the 'interpretation' of the rules, regulations and consensus standards which have been incorporated into NRC guidance documents by reference or endorsement. The resulting increase in the number and complexity of LWR construction requirements has significantly increased the labor content of an LWR construction project. The authors believe that existing nuclear related consensus standards should be reviewed with the objective of modifying the standards to improve the efficiency and productivity of engineering, craft, and non-manual personnel. (author)

49 CFR 176.76 - Transport vehicles, freight containers, and portable tanks containing hazardous materials.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Transport vehicles, freight containers, and... TRANSPORTATION HAZARDOUS MATERIALS REGULATIONS CARRIAGE BY VESSEL General Handling and Stowage § 176.76 Transport... paragraphs (b) through (f) of this section, hazardous materials authorized to be transported by vessel may be...

Toward analytic aids for standard setting in nuclear regulation

International Nuclear Information System (INIS)

Brown, R.V.; O'Connor, M.F.; Peterson, C.R.

1979-05-01

US NRC promulgates standards for nuclear reprocessing and other facilities to safeguard against the diversion of nuclear material. Two broad tasks have been directed toward establishing performance criteria for standard settings: general-purpose modeling, and analysis specific to a particular performance criterion option. This report emphasizes work on the second task. Purpose is to provide a framework for the evaluation of such options that organizes the necessary components in a way that provides for meaningful assessments with respect to required inputs

Quality assurance standards: comparison between IAEA 50-C/SG-Q and ISO 9001:1994

International Nuclear Information System (INIS)

2000-11-01

The International Atomic Energy Agency (IAEA) and the International Organization for Standardization (ISO) agreement regarding the scope and coverage of documents published by both organizations points out that the standards of safety developed by the IAEA are recommendations for use by its Member States in the framework of national regulations for the safe utilization of nuclear energy. Such standards should be considered as nuclear safety regulatory documents. The standards developed by the ISO are complementary technical documents emphasizing industrial application and contractual aspects. Regarding the quality assurance topic, the IAEA standards 50-C/SG-Q are mostly used directly or indirectly to establish the nuclear safety requirements at the utility-regulatory interface. The industrial ISO 9001 standards have progressively been used to implement the quality assurance requirements at the interface utility-supplier. The relationship between both standards is growing in significance owing to the impact upon the owners/operators of nuclear facilities and their contractors/suppliers. The relationship between the IAEA and ISO standards is considered critical, in particular regarding suppliers with a small range of nuclear supplies. These organizations are not always willing to prepare special quality assurance programmes based on nuclear safety standards. On the other hand, these organizations may be qualified on the basis of the ISO quality assurance standards. In any case, for delivering nuclear items and services the quality assurance programme must comply with the requirements established in the nuclear safety regulatory standards. This implies that the utility-supplier will have to demonstrate that the acceptable degree of quality assurance in relation to nuclear safety is accomplished. This may be achieved by imposing additional requirements on the supplier over and above those contained within the ISO. In order to provide a description of the differences

The political economy of regulation: Investigation of the relationship between design and performance standards in surface coal mining

International Nuclear Information System (INIS)

Walker, K.R.

1991-01-01

Research concerning political and economic regulatory policy was conducted on 15 randomly selected surface coal mines in Tennessee. Data on violations were collected over a 6-year period from 1979 through 1984. The primary purpose of this study was to investigate the approaches of the Carter and Reagan administrations concerning the implementation of design and performance regulations of Public Law 95-87. The study concluded that: (1) A change in political administration affects regulatory policy concerning enforcement practices. (2) Regulatory policy is altered in the direction of economic activity believed by an administration to be desirable to society and its constituents. (3) Elaborate rule making activity constrains market activity. (4) The coupling of design and performance standards should be retained. No difference was found in the number of violations for design and associated performance standards. Findings support the theory that it is the administration that affects change in regulatory policy, and not the regulatory construct for compliance with a mandate

Regulating Internalities

OpenAIRE

Sunstein, Cass Robert; Allcott, Hunt

2015-01-01

This paper offers a framework for regulating internalities. Using a simple economic model, we provide four principles for designing and evaluating behaviorally-motivated policy. We then outline rules for determining which contexts reliably reflect true preferences and discuss empirical strategies for measuring internalities. As a case study, we focus on energy efficiency policy, including Corporate Average Fuel Economy (CAFE) standards and appliance and lighting energy efficiency standards.

Developments in safety standards and regulation

International Nuclear Information System (INIS)

Harbison, S.A.

1994-01-01

This paper explains, in broad terms, how regulatory control is exercised over licensed nuclear installations in the UK and how HSE has developed its safety standards to support its regulatory approach. It first sets out the scope of HSE's regulatory responsibilities, which NII exercises on its behalf, and briefly describes the licensing process and compliance monitoring through inspection over the life of a nuclear plant. It also refers to the role of assessment in NII's decision-making processes, and the part played in this by the consideration of costs and safety benefits. It then moves on to consider the challenges that HSE/NII are likely to face from the changing nuclear industry in the second half of the 1990s. (author)

The CPT1C 5'UTR contains a repressing upstream open reading frame that is regulated by cellular energy availability and AMPK.

Directory of Open Access Journals (Sweden)

Ines Lohse

Full Text Available BACKGROUND: Translational control is utilized as a means of regulating gene expression in many species. In most cases, posttranscriptional regulatory mechanisms play an important role in stress response pathways and can lead to dysfunctional physiology if blocked by mutations. Carnitine Palmitoyltransferase 1 C (CPT1C, the brain-specific member of the CPT 1 family, has previously been shown to be involved in regulating metabolism in situations of energy surplus. PRINCIPAL FINDINGS: Sequence analysis of the CPT1C mRNA revealed that it contains an upstream open reading frame (uORF in the 5' UTR of its mRNA. Using CPT1C 5' UTR/luciferase constructs, we investigated the role of the uORF in translational regulation. The results presented here show that translation from the CPT1C main open reading frame (mORF is repressed by the presence of the uORF, that this repression is relieved in response to specific stress stimuli, namely glucose deprivation and palmitate-BSA treatment, and that AMPK inhibition can relieve this uORF-dependent repression. SIGNIFICANCE: The fact that the mORF regulation is relieved in response to a specific set of stress stimuli rather than general stress response, hints at an involvement of CPT1C in cellular energy-sensing pathways and provides further evidence for a role of CPT1C in hypothalamic regulation of energy homeostasis.

A German perspective on advances in safety standards and regulations

International Nuclear Information System (INIS)

Berg, H.P.; Herttrich, P.M.

1993-01-01

At present, different proposals for evolutionary or innovative reactors are under consideration. Therefore, it is necessary that the regulators give guidance on the required safety characteristics of future designs of nuclear power plants. On the one hand, existing regulations have to be updated according to the current state of science and technology. Best available and adequately approved technology has to be used as a yardstick for the acceptability of future basic design features. On the other hand, potential safety features of innovative or revolutionary designs must be considered as serious competitors and potential technical solutions taking the state of maturity of the concepts, the extent of practical experience and the level of effort needed for realization into due account. On this background, recent developments of the Atomic Energy Act, of safety regulations and investigations of requirements for future designs in the Federal Republic of Germany and current projects of international cooperation are presented. (author)

New requirements embodied in expert knowledge regulations for industrial radiation protection officers

International Nuclear Information System (INIS)

Vogt, H.G.

2001-01-01

Expert knowledge standards and certification requirements of health physics responsible persons or radiation safety officers in industry or in health care are laid down in Germany in administrative regulations. Now the new Radiation Protection Ordinance (StrlSchV) contains a specific section exclusively devoted to all aspects of expert knowledge in industrial radiation protection, which inter alia demonstrates the special significance of education and further training of radiation protection specialists. It is expected that the forthcoming new X-ray Ordinance (RoeV) will contain a similar amendment. The article explains the implications of the new Radiation Protection Ordinance for the education and further training of industrial radiation protection officers, but does not address specific aspects of nuclear engineering. (orig./CB) [de

A broader role for AmyR in Aspergillus niger: regulation of the utilisation of D-glucose or D-galactose containing oligo- and polysaccharides.

Science.gov (United States)

vanKuyk, Patricia A; Benen, Jaques A E; Wösten, Han A B; Visser, Jaap; de Vries, Ronald P

2012-01-01

AmyR is commonly considered a regulator of starch degradation whose activity is induced by the presence of maltose, the disaccharide building block of starch. In this study, we demonstrate that the role of AmyR extends beyond starch degradation. Enzyme activity assays, genes expression analysis and growth profiling on D-glucose- and D-galactose-containing oligo- and polysaccharides showed that AmyR regulates the expression of some of the Aspergillus niger genes encoding α- and β-glucosidases, α- and β- galactosidases, as well as genes encoding α-amlyases and glucoamylases. In addition, we provide evidence that D-glucose or a metabolic product thereof may be the inducer of the AmyR system in A. niger and not maltose, as is commonly assumed.

Setting the standard: The IAEA safety standards set the global reference

International Nuclear Information System (INIS)

Williams, L.

2003-01-01

For the IAEA, setting and promoting standards for nuclear radiation, waste, and transport safety have been priorities from the start, rooted in the Agency's 1957 Statute. Today, a corpus of international standards are in place that national regulators and industries in many countries are applying, and more are being encouraged and assisted to follow them. Considerable work is done to keep safety standards updated and authoritative. They cover five main areas: the safety of nuclear facilities; radiation protection and safety of radiation sources; safe management of radioactive waste; safe transport of radioactive material; and thematic safety areas, such as emergency preparedness or legal infrastructures. Overall, the safety standards reflect an international consensus on what constitutes a high level of safety for protecting people and the environment. All IAEA Member States can nominate experts for the Agency standards committees and provide comments on draft standards. Through this ongoing cycle of review and feedback, the standards are refined, updated, and extended where needed

Bisphenol-A induces expression of HOXC6, an estrogen-regulated homeobox-containing gene associated with breast cancer.

Science.gov (United States)

Hussain, Imran; Bhan, Arunoday; Ansari, Khairul I; Deb, Paromita; Bobzean, Samara A M; Perrotti, Linda I; Mandal, Subhrangsu S

2015-06-01

HOXC6 is a homeobox-containing gene associated with mammary gland development and is overexpressed in variety of cancers including breast and prostate cancers. Here, we have examined the expression of HOXC6 in breast cancer tissue, investigated its transcriptional regulation via estradiol (E2) and bisphenol-A (BPA, an estrogenic endocrine disruptor) in vitro and in vivo. We observed that HOXC6 is differentially over-expressed in breast cancer tissue. E2 induces HOXC6 expression in cultured breast cancer cells and in mammary glands of Sprague Dawley rats. HOXC6 expression is also induced upon exposure to BPA both in vitro and in vivo. Estrogen-receptor-alpha (ERα) and ER-coregulators such as MLL-histone methylases are bound to the HOXC6 promoter upon exposure to E2 or BPA and that resulted in increased histone H3K4-trimethylation, histone acetylation, and recruitment of RNA polymerase II at the HOXC6 promoter. HOXC6 overexpression induces expression of tumor growth factors and facilitates growth 3D-colony formation, indicating its potential roles in tumor growth. Our studies demonstrate that HOXC6, which is a critical player in mammary gland development, is upregulated in multiple cases of breast cancer, and is transcriptionally regulated by E2 and BPA, in vitro and in vivo. Published by Elsevier B.V.

Optogenetic inhibition of D1R containing nucleus accumbens neurons alters cocaine- mediated regulation of Tiam1

Directory of Open Access Journals (Sweden)

Ramesh eChandra

2013-05-01

Full Text Available Exposure to psychostimulants results in structural and synaptic plasticity in striatal medium spiny neurons (MSNs. These cellular adaptations arise from alterations in genes that are highly implicated in the rearrangement of the actin cytoskeleton, such as Tiam1. Previous studies have demonstrated a crucial role for dopamine receptor 1 (D1-containing striatal MSNs in mediating psychostimulant induced plasticity changes. These D1-MSNs in the nucleus accumbens (NAc positively regulate drug seeking, reward, and locomotor behavioral effects as well as the morphological adaptations of psychostimulant drugs. Here, we demonstrate that rats that actively self-administer cocaine display reduced levels of Tiam1 in the NAc. To further examine the cell type specific contribution to these changes in Tiam1 we used optogenetics to selectively manipulate NAc D1-MSNs or dopamine receptor 2 (D2 expressing MSNs. We find that repeated ChR2 activation of D1-MSNs but not D2-MSNs caused a down-regulation of Tiam1 levels similar to the effects of cocaine. Further, activation of D2-MSNs, which caused a late blunted cocaine-mediated locomotor behavioral response, did not alter Tiam1 levels. We then examined the contribution of D1-MSNs to the cocaine-mediated decrease of Tiam1. Using the light activated chloride pump, eNpHR3.0, we selectively inhibited D1-MSNs during cocaine exposure, which resulted in a behavioral blockade of cocaine-induced locomotor sensitization. Moreover, inhibiting these NAc D1-MSNs during cocaine exposure reversed the down-regulation of Tiam1 gene expression and protein levels. These data demonstrate that altering activity in specific neural circuits with optogenetics can impact the underlying molecular substrates of psychostimulant mediated behavior and function.

Radiation emitting devices regulations

International Nuclear Information System (INIS)

1970-01-01

The Radiation Emitting Devices Regulations are the regulations referred to in the Radiation Emitting Devices Act and relate to the operation of devices. They include standards of design and construction, standards of functioning, warning symbol specifications in addition to information relating to the seizure and detention of machines failing to comply with the regulations. The radiation emitting devices consist of the following: television receivers, extra-oral dental x-ray equipment, microwave ovens, baggage inspection x-ray devices, demonstration--type gas discharge devices, photofluorographic x-ray equipment, laser scanners, demonstration lasers, low energy electron microscopes, high intensity mercury vapour discharge lamps, sunlamps, diagnostic x-ray equipment, ultrasound therapy devices, x-ray diffraction equipment, cabinet x-ray equipment and therapeutic x-ray equipment

Two new pollution regulations introduced

International Nuclear Information System (INIS)

Anon.

2000-01-01

A newly proposed regulation in Ontario will require the mandatory tracking of 358 airborne pollutants by the electricity sector as well as by other large industrial facilities such as iron and steel manufacturers and petroleum refiners. If passed, the regulation would make Ontario the first jurisdiction in the world to require monitoring and reporting of a full suite of major greenhouse gases, including smog and acid-rain causing emissions. The proposed regulation also provides for immediate public access to any reported information. Ontario residents can comment on the proposed regulation through the Environmental Bill of Rights registry. A new, more severe hazardous waste regulation will also take effect on March 31, 2001, whereby testing for 88 contaminants will be done according to a new standard called the Toxicity Characteristic Leaching Procedure (TCLP). This new regulation also introduces a new 'derived from' rule which requires that a listed hazardous waste keep its classification until it can be demonstrated otherwise. Ontario's list of hazardous wastes has been updated to include 129 new chemicals and industrial processes. The Ontario Ministry has also adopted the Canada-wide Standards for Particulate Matter and Ozone, as well as the Canada-wide Standards for mercury emissions from base metal smelters as well as from incineration of sewage sludge and municipal, medical, hazardous waste

Nuclear Regulatory Commission and its role in environmental standards

International Nuclear Information System (INIS)

Mattson, R.J.

1976-01-01

The NRC and its predecessors in the Atomic Energy Commission represent considerable experience in environmental standards setting. The Atomic Energy Act of 1954, the 1970 Supreme Court decision on Federal pre-emption of radiation standards, the Calvert Cliffs decision of 1971, the Energy Reorganization Act of 1974, and the Appendix I ''as low as reasonably achievable'' decision of 1975, to name a few of our landmarks, are representative of the scars and the achievements of being in a role of national leadership in radiation protection. The NRC, through a variety of legislative authorities, administrative regulations, regulatory guides, and national consensus standards regulates the commercial applications of nuclear energy. The purposes of regulation are the protection of the environment, public health and safety, and national security. To understand NRC's responsibilities relative to those of other Federal and state agencies concerned with environmental protection, we will briefly review the legislative authorities which underlie our regulatory program. Then we will examine the intent or the spirit of that program as embodied in our system of regulations, guides, and standards. Finally we will speak to what's happening today and what we see in the future for environmental standards

Radiation protection of the public in respect of consumer goods containing radioactive substances

International Nuclear Information System (INIS)

1984-01-01

The use of consumer goods containing radioactive substances makes a contribution to the total exposure of man to ionizing radiation. This contribution is explicitly recognized in Section II of the Basic Safety Standards established pursuant to Article 30 of the Euratom Treaty for the health protection of the general public and workers against the dangers of ionizing radiation, first published in 1959 and most recently revised 15 July 1980. Nevertheless, the Standards are of a general nature and need to be expanded on to be of practical application in this field. National authorities must have additional information in order to attain in full the objectives stated in them. This guide has been prepared with these considerations in mind. The guide is not a set of regulations but is better described as a code of practice, drawn up by specialists and approved by the scientific experts in the field of radiological protection and public health appointed under Article 31 of the Euratom Treaty

Transient shielded liquid hydrogen containers

International Nuclear Information System (INIS)

Varghese, A.P.; Herring, R.H.

1990-01-01

The storage of hydrogen in the liquid phase has been limited in duration due to the thermal performance constraints of conventional Liquid Hydrogen containers available. Conventional Liquid Hydrogen containers lose hydrogen because of their relatively high heat leak and variations in usage pattern of hydrogen due to shutdowns. Local regulations also discourage venting of hydrogen. Long term storage of Liquid Hydrogen without product loss was usually accomplished using Liquid Nitrogen sacrificial shields. This paper reports on a new low heat leak container developed and patented that will extend the storage time of liquid hydrogen by five hundred percent. The principle of operation of the Transient Shields which makes the extraordinary performance of this container feasible is described in this paper. Also covered are the impact of this new container on present applications of hydrogen and the new opportunities afforded to Liquid hydrogen in the world hydrogen market

Tworty Box to Improve the Equipment Logistics of Container Lines

Directory of Open Access Journals (Sweden)

Ulrich Malchow

2016-07-01

Full Text Available A major share of all empty container positioning (deadheading is resulting from imbalances with regard to container sizes (20ft/40ft. In order to reduce the shipments of 'containerised air' a new type of container has been developed by the author: The Tworty Boxes can either be used as a standard 20ft or in coupled condition as a 40ft container. The outside appearance resembles any standard 20ft container. However the Tworty Box is unique in that it has an additional door at the front side that opens to the inside. This door can be fixed to the ceiling and by using of bonding elements another Tworty Box can be joined up, thereby creating the full 40ft inside space. Operated as a single 20ft box the additional door remains locked, access is only through the existing standard door. Tworty Boxes do not require any additional components and fulfil all ISO and CSC requirements.

48 CFR 9904.406 - Cost accounting standard-cost accounting period.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 7 2010-10-01 2010-10-01 false Cost accounting standard-cost accounting period. 9904.406 Section 9904.406 Federal Acquisition Regulations System COST ACCOUNTING STANDARDS BOARD, OFFICE OF FEDERAL PROCUREMENT POLICY, OFFICE OF MANAGEMENT AND BUDGET PROCUREMENT...

Regional hydrocarbon contaminated soil recycling facility standards

International Nuclear Information System (INIS)

Warren, R.

1992-01-01

In an effort to protect the environment from uncontrolled releases of petroleum products, the Canadian Petroleum Products Institute member companies have initiated environmental upgrading programs for their underground fuel storage systems in British Columbia. These programs have been restricted in recent years as a result of environmental regulations targeting contaminated soil, which is generated when underground storage tanks are upgraded to current standards. The soil requiring treatment is typically sand backfill containing a nominal value of petroleum product. These soils can be treated in an engineered basin using bioremediation technology to reduce the level of contamination. Depending on the degree of treatment, the soil can be recycled as backfill or reused as landfill cover. An overview is presented of the basin treatment process and design. Natural bioremediation is enhanced with nutrients, water and oxygen addition. 4 figs

Standardization and workers' protection legislation

International Nuclear Information System (INIS)

Kliesch, G.

1979-01-01

There are distinct laws guaranteeing the protection of workers in the social and medical field, but the protection of workers in the technical field is based on a simple, general clause relating to technical standards, i.e. to a confusing variety of regulations. The author therefore asks for DIN standards to be set up in order to achieve a consistent and uniform set of rules and regulations. He furthermore points out that it is up to the government to initiate appropriate procedures within the framework of constitutional law towards solving the essential problem, namely that of directly incorporating technical expert knowledge in legal provisions. (HSCH) [de

Special Education Compliance: Program Review Standards and Indicators.

Science.gov (United States)

Missouri State Dept. of Elementary and Secondary Education, Jefferson City. Div. of Special Education.

This manual contains special education standards and indicators for educating children with disabilities in Missouri. It is divided into four main sections. Section 1 contains special education compliance standards based upon the federal Office of Special Education Programs Continuous Improvement Monitoring Program clusters and indicators. The…

Assessing the disposal of wastes containing NORM in nonhazardous waste landfills

International Nuclear Information System (INIS)

Smith, K. P.; Blunt, D. L.; Williams, G. P.; Arnish, J. J.; Pfingston, M. R.; Herbert, J.

1999-01-01

In the past few years, many states have established specific regulations for the management of petroleum industry wastes containing naturally occurring radioactive material (NORM) above specified thresholds. These regulations have limited the number of disposal options available for NORM-containing wastes, thereby increasing the related waste management costs. In view of the increasing economic burden associated with NORM management, industry and regulators are interested in identifying cost-effective disposal alternatives that still provide adequate protection of human health and the environment. One such alternative being considered is the disposal of NORM-containing wastes in landfills permitted to accept only nonhazardous wastes. The disposal of petroleum industry wastes containing radium-226 and lead-210 above regulated levels in nonhazardous landfills was modeled to evaluate the potential radiological doses and associated health risks to workers and the general public. A variety of scenarios were considered to evaluate the effects associated with the operational phase (i.e., during landfill operations) and future use of the landfill property. Doses were calculated for the maximally exposed receptor for each scenario. This paper presents the results of that study and some conclusions and recommendations drawn from it

Standard format and content of financial assurance mechanisms required for decommissioning under 10 CFR parts 30, 40, 70, and 72

International Nuclear Information System (INIS)

1990-01-01

The Nuclear Regulatory Commission (NRC) has established technical and financial regulations for decommissioning licensed nuclear facilities (53 FR 24018, June 27, 1988). The regulations address decommissioning planning needs, timing, funding methods, and environmental review requirements for public and private facilities holding licenses under 10 CFR Parts 30, 40, 50, 70, and 72, with the exception of uranium mills. The intent of the regulations is to ensure that the decommissioning of all licensed facilities will be accomplished in a safe and timely manner and that licensees will provide adequate funds to cover all costs associated with decommissioning. The purpose of this regulatory guide, ''Standard Format and Content of Financial Assurance Mechanisms Required for Decommissioning Under 10 CFR Parts 30, 40, 70, and 72,'' is to provide guidance acceptable to the NRC staff on the information to be provided for establishing financial assurance for decommissioning and to establish a standard format for presenting the information. Use of the standard format will (1) help ensure that the financial instruments contain the information required by 10 CFR Parts 30, 40, 70, and 72, (2) aid the applicant and NRC staff in ensuring that the information is complete, and (3) help persons reading the financial instruments to locate information. 5 refs., 13 figs

Standard Populations (Millions) for Age-Adjustment - SEER Population Datasets

Science.gov (United States)

Download files containing standard population data for use in statististical software. The files contain the same data distributed with SEER*Stat software. You can also view the standard populations, either 19 age groups or single ages.

5 CFR 2635.202 - General standards.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 3 2010-01-01 2010-01-01 false General standards. 2635.202 Section 2635.202 Administrative Personnel OFFICE OF GOVERNMENT ETHICS GOVERNMENT ETHICS STANDARDS OF ETHICAL... contrary to applicable regulations, policies or guidance relating to the procurement of supplies and...

Regulations for the safe transport of radioactive materials. Notes on certain aspects of the regulations

International Nuclear Information System (INIS)

1961-01-01

The notes attempt to provide some broad general guidance to users as to the purpose of the regulations and their working out in practice. They contain also the scientific background to the classification of radioisotopes for transport purposes given in the regulations. Furthermore, an approach was made to the difficult question of design of containers in relation to the factors that have to be taken into account by competent authorities in approving Type B containers, with a view both to helping those concerned on both sides of this transport problem, and to stimulating further thought on the subject, in order to build up a corpus of practical experience in this field.

Aspects on Media Self Regulation Reflected in the Activity of Romanian Journalists

Directory of Open Access Journals (Sweden)

Daniela Aurelia Popa

2011-05-01

Full Text Available The media organizations in Romania, reticent to the idea to constraint the press freedom, manage to understand the importance of implementing a system of media responsibility. Therefore, the present study is a research in incipient stage that begins with the identification of the initiatives of media self regulation as an alternative to the efforts of enacting press in Romania. The identification of the self regulating system in Romania will be accomplished through the description of the context of development of the media responsibility system in the Romanian journalistic culture and by underlining the self regulation initiatives. For the delineation and establishment of such important self regulation initiatives, the activity of an ethical instance is necessary, for the defense and solving cases of norms contained by the new deontological code. The establishment of such an instance in Romania will represent a viable solution for the development of a more ethical professional environment that confirms the assumption of media responsibility for the adhesion to quality journalistic standards.

Standards for radiation protection instrumentation: design of safety standards and testing procedures

International Nuclear Information System (INIS)

Meissner, Frank

2008-01-01

This paper describes by means of examples the role of safety standards for radiation protection and the testing and qualification procedures. The development and qualification of radiation protection instrumentation is a significant part of the work of TUV NORD SysTec, an independent expert organisation in Germany. The German Nuclear Safety Standards Commission (KTA) establishes regulations in the field of nuclear safety. The examples presented may be of importance for governments and nuclear safety authorities, for nuclear operators and for manufacturers worldwide. They demonstrate the advantage of standards in the design of radiation protection instrumentation for new power plants, in the upgrade of existing instrumentation to nuclear safety standards or in the application of safety standards to newly developed equipment. Furthermore, they show how authorities may proceed when safety standards for radiation protection instrumentation are not yet established or require actualization. (author)

3084 ROYAL DECREE No 53/1992 of 24 January 1992 approving the Regulation on Health Protection against Ionizing Radiation

International Nuclear Information System (INIS)

1992-01-01

The purpose of this new Regulation is to unite in a single instrument the existing rules on this subject contained in Decree 2519/1982 as amended by Decree 1753/1987, now repealed, as well as to introduce certain modifications which have proved desirable in the light of the practical application of those rules. The 1987 Decree reflected the basic safety standards of the Euratom Directives. Like that Decree, the new regulation lays down the measures for protection of the public and occupationally exposed persons against the dangers of ionizing radiation. The Regulation is supplemented by Appendices providing for definitions of radiological, biological and medical terms, annual dose limits for the public and for occupationally exposed persons, etc. (NEA)

Nutrition standards for away-from-home foods in the USA.

Science.gov (United States)

Cohen, D A; Bhatia, R

2012-07-01

Away-from-home foods are regulated with respect to the prevention of food-borne diseases and potential contaminants, but not for their contribution to dietary-related chronic diseases. Away-from-home foods have more calories, salt, sugar and fat, and include fewer fruits and vegetables than recommended by national nutrition guidelines. Thus, frequent consumption of away-from-home foods contributes to obesity, hypertension, diabetes, heart disease, and cancer. In light of this, many localities are already adopting regulations or sponsoring programs to improve the quality of away-from-home foods. We review the rationale for developing nutritional performance standards for away-from-home foods in light of limited human capacity to regulate intake or physiologically compensate for a poor diet. We offer a set of model performance standards to be considered as a new area of environmental regulation. Models for voluntary implementation of consumer standards exist in the environmental domain and may be useful templates for implementation. Implementing such standards, whether voluntarily or via regulations, will require addressing a number of practical and ideological challenges. Politically, regulatory standards contradict the belief that adults should be able to navigate dietary risks in away-from-home settings unaided. © 2012 The Authors. obesity reviews © 2012 International Association for the Study of Obesity.

Westinghouse radiological containment guide

International Nuclear Information System (INIS)

Aitken, S.B.; Brown, R.L.; Cantrell, J.R.; Wilcox, D.P.

1994-03-01

This document provides uniform guidance for Westinghouse contractors on the implementation of radiological containments. This document reflects standard industry practices and is provided as a guide. The guidance presented herein is consistent with the requirements of the DOE Radiological Control Manual (DOE N 5480.6). This guidance should further serve to enable and encourage the use of containments for contamination control and to accomplish the following: Minimize personnel contamination; Prevent the spread of contamination; Minimize the required use of protective clothing and personal protective equipment; Minimize the generation of waste

Westinghouse radiological containment guide

Energy Technology Data Exchange (ETDEWEB)

Aitken, S.B. [Idaho National Engineering Lab., Idaho Falls, ID (United States); Brown, R.L. [Westinghouse Hanford Co., Richland, WA (United States); Cantrell, J.R. [Westinghouse Savannah River Co., Aiken, SC (United States); Wilcox, D.P. [West Valley Nuclear Services Co., Inc., West Valley, NY (United States)

1994-03-01

This document provides uniform guidance for Westinghouse contractors on the implementation of radiological containments. This document reflects standard industry practices and is provided as a guide. The guidance presented herein is consistent with the requirements of the DOE Radiological Control Manual (DOE N 5480.6). This guidance should further serve to enable and encourage the use of containments for contamination control and to accomplish the following: Minimize personnel contamination; Prevent the spread of contamination; Minimize the required use of protective clothing and personal protective equipment; Minimize the generation of waste.

Meeting licensing restrictions from a regulator's perspective

International Nuclear Information System (INIS)

Autry, V.R.; Ragan, F.A.

1990-01-01

The State of South Carolina was delegated the authority by the US Nuclear Regulatory Commission to regulate the receipt, possession, use and disposal of radioactive material as an Agreement State. Since 1970, the state has been the principal regulatory authority for the Barnwell Low-Level Waste Disposal Facility operated by Chem-Nuclear Systems, Inc. The radioactive material license issued authorizing the receipt and disposal of low level waste has experienced many changes necessitated by technical advancements which led to stricter controls and restrictions for shallow land disposal. Low level waste has evolved from simple contaminated items with minimal radioactivity, to complex waste streams requiring elaborate processing and containment of high quantities of radionuclides. Waste streams also require extensive analysis and qualification to meet many of the restrictions imposed at the burial facility and comply with national standards and regulations for classification. This paper presents a chronological history of many of these restrictions, the rationale for them, and the waste generators' abilities and inabilities to comply. In addition, case histories of some examples are discussed

Development of suitable plastic standards for X-ray fluorescence analysis

Energy Technology Data Exchange (ETDEWEB)

Mans, Christian [University of Applied Sciences Muenster, Department of Chemical Engineering, Advanced Analytical Chemistry, Stegerwaldstr. 39, 48565 Steinfurt (Germany)], E-mail: c.mans@fh-muenster.de; Hanning, Stephanie [University of Applied Sciences Muenster, Department of Chemical Engineering, Advanced Analytical Chemistry, Stegerwaldstr. 39, 48565 Steinfurt (Germany)], E-mail: hanning@fh-muenster.de; Simons, Christoph [University of Applied Sciences Muenster, Department of Chemical Engineering, Advanced Analytical Chemistry, Stegerwaldstr. 39, 48565 Steinfurt (Germany)], E-mail: simons@fh-muenster.de; Wegner, Anne [University of Applied Sciences Muenster, Department of Chemical Engineering, Advanced Analytical Chemistry, Stegerwaldstr. 39, 48565 Steinfurt (Germany)], E-mail: awegner@fh-muenster.de; Janssen, Anton [University of Applied Sciences Muenster, Department of Chemical Engineering, Advanced Analytical Chemistry, Stegerwaldstr. 39, 48565 Steinfurt (Germany)], E-mail: janssena@fh-muenster.de; Kreyenschmidt, Martin [University of Applied Sciences Muenster, Department of Chemical Engineering, Advanced Analytical Chemistry, Stegerwaldstr. 39, 48565 Steinfurt (Germany)], E-mail: martin.kreyenschmidt@fh-muenster.de

2007-02-15

For the adoption of the EU directive 'Restriction on use of certain Hazardous Substances' and 'Waste Electrical and Electronic Equipment' using X-ray fluorescence analysis suitable standard materials are required. Plastic standards based on acrylonitrile-butadiene-styrene terpolymer, containing the regulated elements Br, Cd, Cr, Hg and Pb were developed and produced as granulates and solid bodies. The calibration materials were not generated as a dilution from one master batch but rather the element concentrations were distributed over nine independent calibration samples. This was necessary to enable inter-elemental corrections and empirical constant mass absorption coefficients. The produced standard materials are characterized by a homogenous element distribution, which is more than sufficient for X-ray fluorescence analysis. Concentrations for all elements except for Br could be determined by Inductively Coupled Plasma Atomic Emission Spectroscopy after microwave assisted digestion. The concentration of Br was determined by use of Neutron Activation Analysis at Hahn-Meitner-Institute in Berlin, Germany. The correlation of the X-ray fluorescence analysis measurements with the values determined using Inductively Coupled Plasma Atomic Emission Spectroscopy and Neutron Activation Analysis showed a very good linearity.

T25 Qualification of old containers

International Nuclear Information System (INIS)

Hoerning, T.; Kasparek, E.M.; Voelzke, H.

2013-01-01

Radioactive waste for final disposal in the repository Konrad has to be packaged in licensed containers. The qualification of containers is performed according the respective standards and BfS requirements. The latter ones differ for different container types with respect to accident resistance based on the release behavior of the waste. Usually qualification of container types is performed before series production. The qualification of already produced containers (''old containers'') is significantly more complicated. The differences of quality assurance and materials properties of the older containers have to be evaluated. A main tool for this evaluation is the numerical re-calculation of accident scenarios for estimation of the safety margins. The validation of appropriate finite element models is available. Based on these date it might be possible to abandon additional drop tests with the existing old containers to prove the structural integrity.

Yes-associated protein and WW-containing transcription regulator 1 regulate the expression of sex-determining genes in Sertoli cells, but their inactivation does not cause sex reversal.

Science.gov (United States)

Levasseur, Adrien; Paquet, Marilène; Boerboom, Derek; Boyer, Alexandre

2017-07-01

Yes-associated protein (YAP) and WW-containing transcription regulator 1 (WWTR1) are two functionally redundant transcriptional regulators that are downstream effectors of the Hippo signaling pathway, and that act as major regulators of cell growth and differentiation. To elucidate their role in Sertoli cells, primary Sertoli cell culture from Yapflox/flox; Wwtr1flox/flox animals were infected with a Cre recombinase-expressing adenovirus. Concomitant inactivation of Yap and Wwtr1 resulted in a decrease in the mRNA levels of the male sex differentiation genes Dhh, Dmrt1, Sox9, and Wt1, whereas those of genes involved in female differentiation (Wnt4, Rspo1, and Foxl2) were induced. SOX9, FOXL2, and WNT4 proteins were regulated in the same manner as their mRNAs in response to loss of YAP and WWTR1. To further characterize the role of YAP and WWTR1 in Sertoli cells, we generated a mouse model (Yapflox/flox; Wwtr1flox/flox; Amhcre/+) in which Yap and Wwtr1 were conditionally deleted in Sertoli cells. An increase in the number of apoptotic cells was observed in the seminiferous tubules of 4 dpp mutant mice, leading to a reduction in testis weights and a decrease in the number of Sertoli cells in adult animals. Gene expression analyses of testes from 4 dpp Yapflox/flox; Wwtr1flox/flox; Amhcre/+ mice showed that Sertoli cell differentiation is initially altered, as Dhh, Dmrt1, and Sox9 mRNA levels were downregulated, whereas Wnt4 mRNA levels were increased. However, expression of these genes was not changed in older animals. Together, these results suggest a novel role of the Hippo signaling pathway in the mechanisms of sex differentiation. © The Authors 2017. Published by Oxford University Press on behalf of Society for the Study of Reproduction. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Nuclear reactor pressure vessel surveillance capsule examinations. Application of American Society for Testing and Materials Standards

International Nuclear Information System (INIS)

Perrin, J.S.

1978-01-01

A series of pressure vessel surveillance capsules is installed in each commercial nuclear power plant in the United States. A capsule typically contains neutron dose meters, thermal monitors, tensile specimens, and Charpy V-notch impact specimens. In order to determine property changes of the pressure vessel resulting from irradiation, surveillance capsules are periodically removed during the life of a reactor and examined. There are numerous standards, regulations, and codes governing US pressure vessel surveillance capsule programmes. These are put out by the US Nuclear Regulatory Commission, the Boiler and Pressure Vessel Committee of the American Society of Mechanical Engineers, and the American Society for Testing and Materials (ASTM). A majority of the pertinent ASTM standards are under the jurisdiction of ASTM Committee E-10 on Nuclear Applications and Measurements of Radiation Effects. The standards, regulations, and codes pertaining to pressure vessel surveillance play an important role in ensuring reliability of the nuclear pressure vessels. ASTM E 185-73 is the Standard Recommended Practice for Surveillance Tests for Nuclear Reactors. This standard recommends procedures for both the irradiation and subsequent testing of surveillance capsules. ASTM E 185-73 references many additional specialized ASTM standards to be followed in specific areas of a surveillance capsule examination. A key element of surveillance capsule programmes is the Charpy V-notch impact test, used to define curves of fracture behaviour over a range of temperatures. The data from these tests are used to define the adjusted reference temperature used in determining pressure-temperature operating curves for a nuclear power plant. (author)

Air kerma standardization for diagnostic radiology in a secondary standard laboratory

International Nuclear Information System (INIS)

Ramos, Manoel M.O.; Peixoto, J. Guilherme P.; Lopes, Ricardo T.

2009-01-01

The demand for calibration services and quality control in diagnostic radiology has grown in the country since the publication of the governmental regulation 453, issued by the Brazilian Ministry of Health in 1998. At that time, to produce results facing the new legislation, many laboratories used different standards and radiation qualities, some of which could be inadequate. The international standards neither supplied consistent radiation qualities and standardization for the different types of equipment available. This situation changed with the publication of the new edition of the IEC 61267 standard, published in 2005. The objective of this work was to implement the standardization of the air kerma for the unatenuated qualities (RQR) of IEC 61267 in the National Laboratory of Metrology of the Ionizing Radiations (LNMRI) of the Institute of Radiation Protection and Dosimetry (IRD). Technical procedures were developed together with uncertainty budget. Results of interlaboratory comparisons demonstrate that the quantity is standardized and internationally traceable. (author)

Nuclear standards

International Nuclear Information System (INIS)

Fichtner, N.; Becker, K.; Bashir, M.

1981-01-01

This compilation of all nuclear standards available to the authors by mid 1980 represents the third, carefully revised edition of a catalogue which was first published in 1975 as EUR 5362. In this third edition several changes have been made. The title has been condensed. The information has again been carefully up-dated, covering all changes regarding status, withdrawal of old standards, new projects, amendments, revisions, splitting of standards into several parts, combination of several standards into one, etc., as available to the authors by mid 1980. The speed with which information travels varies and requires in many cases rather tedious and cumbersome inquiries. Also, the classification scheme has been revised with the goal of better adjustment to changing situations and priorities. Whenever it turned out to be difficult to attribute a standard to a single subject category, multiple listings in all relevant categories have been made. As in previous editions, within the subcategories the standards are arranged by organization (in Categorie 2.1 by country) alphabetically and in ascending numerical order. It covers all relevant areas of power reactors, the fuel cycle, radiation protection, etc., from the basic laws and governmental regulations, regulatory guides, etc., all the way to voluntary industrial standards and codes of pratice. (orig./HP)

V-set and Ig domain-containing 4 (VSIG4)-expressing hepatic F4/80+ cells regulate oral antigen-specific responses in mouse.

Science.gov (United States)

Shin, Wonhwa; Jeon, Youkyoung; Choi, Inhak; Kim, Yeon-Jeong

2018-04-01

Oral tolerance can prevent unnecessary immune responses against dietary antigens. Members of the B7 protein family play critical roles in the positive and/or negative regulation of T cell responses to interactions between APCs and T cells. V-set and Ig domain-containing 4 (VSIG4), a B7-related co-signaling molecule, has been known to act as a co-inhibitory ligand and may be critical in establishing immune tolerance. Therefore, we investigated the regulation of VSIG4 signaling in a food allergy and experimental oral tolerance murine models. We analyzed the contributions of the two main sites involved in oral tolerance, the mesenteric lymph node (MLN) and the liver, in VSIG4-mediated oral tolerance induction. Through the comparative analysis of major APCs, dendritic cells (DCs) and macrophages, we found that Kupffer cells play a critical role in inducing regulatory T cells (Tregs) and establishing immune tolerance against oral antigens via VSIG4 signaling. Taken together, these results suggest the possibility of VSIG4 signaling-based regulation of orally administered antigens. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Nutrition Standards for Away-from-home Foods in the United States

Science.gov (United States)

Cohen, Deborah A.; Bhatia, Rajiv

2012-01-01

Away-from-home foods are regulated with respect to the prevention of food-borne diseases and potential contaminants, but not for their contribution to dietary-related chronic diseases. Away-from-home foods have more calories, salt, sugar, and fat and provide fewer fruits and vegetables than recommended by national nutrition guidelines; thus, frequent consumption of away-from-home foods contributes to obesity, hypertension, diabetes, heart disease, and cancer. In light of this, many localities are already adopting regulations or sponsoring programs to improve the quality of away-from-home foods. We review the rationale for developing nutritional performance standards for away-from-home foods in light of limited human capacity to regulate intake or physiologically compensate for a poor diet. We offer a set of model performance standards to be considered as a new area of environmental regulation. Models for voluntary implementation of consumer standards exist in the environmental domain and may be useful templates for implementation. Implementing such standards, whether voluntarily or via regulations, will require addressing a number of practical and ideological challenges. Politically, regulatory standards contradict the belief that adults should be able to navigate dietary risks in away-from-home settings unaided. PMID:22329431

Regulation of above-ground oil and waste containers. Hearing before the Subcommittee on Transportation, Tourism, and Hazardous Materials of the Committee on Energy and Commerce, House of Representatives, One Hundredth Congress, Second Session, January 26, 1988

Energy Technology Data Exchange (ETDEWEB)

1988-01-01

Representatives from the petroleum industry, US EPA, National Bureau of Standards and Congress were among those testifying at a hearing to discuss one of the worst inland environmental disasters in this Nation's history. The January 2 collapse of the Ashland Oil Co.'s storage tank in Floreffe, Pennsylvania resulted in the release of some 4 million gallons of diesel fuel. Approximately a million gallons escaped the containment structures and spilled over into the Monongahela River. This spill has contaminated the drinking water sources for millions of people downstream, from Pittsburgh to Cincinnati to Louisville, and beyond. Attention is focused on the causes of this tank's collapse, the response measures taken by Ashland Oil, the Coast Guard, the EPA, and the need for tighter federal regulations of above-ground tanks used for the storage of petroleum and hazardous substances.

Fulfilling a Promise: Standards for Technological Literacy.

Science.gov (United States)

Bybee, Rodger W.

2003-01-01

Discusses the place of standards in U.S. education, the development of the Standards for Technological Literacy, and the recent publication of "Advancing Excellence in Technological Literacy: Student Assessment, Professional Development, and Program Standards." (Contains 21 references.) (SK)

Biosafety and Biosecurity in European Containment Level 3 Laboratories: Focus on French Recent Progress and Essential Requirements

Directory of Open Access Journals (Sweden)

Boris Pastorino

2017-05-01

Full Text Available Even if European Union (EU Member States are obliged to implement EU Directives 2000/54/EC on the protection of workers from risks related to exposure to biological agents at work, national biosafety regulations and practices varied from country to country. In fact, EU legislation on biological agents and genetically modified microorganisms is often not specific enough to ensure harmonization leading to difficulties in implementation for most laboratories. In the same way, biosecurity is a relatively new concept and a few EU Member States are known to have introduced national laboratory biosecurity legislation. In France, recent regulations have reinforced biosafety/biosecurity in containment level 3 (CL-3 laboratories but they concern a specific list of pathogens with no correlation in other European Members States. The objective of this review was to summarize European biosafety/biosecurity measures concerning CL-3 facilities focusing on French specificities. Essential requirements needed to preserve efficient biosafety measures when manipulating risk group 3 biological agents are highlighted. In addition, International, European and French standards related to containment laboratory planning, operation or biosafety equipment are described to clarify optimal biosafety and biosecurity requirements.

Biosafety and Biosecurity in European Containment Level 3 Laboratories: Focus on French Recent Progress and Essential Requirements.

Science.gov (United States)

Pastorino, Boris; de Lamballerie, Xavier; Charrel, Rémi

2017-01-01

Even if European Union (EU) Member States are obliged to implement EU Directives 2000/54/EC on the protection of workers from risks related to exposure to biological agents at work , national biosafety regulations and practices varied from country to country. In fact, EU legislation on biological agents and genetically modified microorganisms is often not specific enough to ensure harmonization leading to difficulties in implementation for most laboratories. In the same way, biosecurity is a relatively new concept and a few EU Member States are known to have introduced national laboratory biosecurity legislation. In France, recent regulations have reinforced biosafety/biosecurity in containment level 3 (CL-3) laboratories but they concern a specific list of pathogens with no correlation in other European Members States. The objective of this review was to summarize European biosafety/biosecurity measures concerning CL-3 facilities focusing on French specificities. Essential requirements needed to preserve efficient biosafety measures when manipulating risk group 3 biological agents are highlighted. In addition, International, European and French standards related to containment laboratory planning, operation or biosafety equipment are described to clarify optimal biosafety and biosecurity requirements.

5 CFR 179.301 - Scope of regulations.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Scope of regulations. 179.301 Section 179.301 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS CLAIMS COLLECTION STANDARDS Administrative Offset § 179.301 Scope of regulations. These regulations apply to the...

41 CFR 101-42.1102-7 - Lead-containing paint and items bearing lead-containing paint.

Science.gov (United States)

2010-07-01

... be in conformance with Occupational Safety and Health Administration (OSHA) regulations at 29 CFR... property requested herein shall be used only as specified in 16 CFR 1303.3 and in no case shall be...) Abandonment and destruction. In no case shall lead-containing paint or consumer products bearing lead...

CONSOLIDATED FINANCIAL STATEMENTS IN UKRAINE: NORMATIVE AND LEGAL REGULATION STATE

Directory of Open Access Journals (Sweden)

S.V. Kucher

2016-09-01

Full Text Available The development of big business in Ukraine has led to the need to release a number of domestic companies and their groups and associations to the international financial market which was the prerequisite of the needs of users of financial statements to obtain reliable information about the activities of such companies. In accordance with the national legislation associations of enterprises and companies have to provide the consolidated financial statements which contain the pooled indices about the activities of these entities. The article analyzes the current state of normative and legal regulation of financial reporting consolidation process in Ukraine. In particular, the paper determines the basic legal acts of regulations of national and international governing process of preparation of consolidated financial statements; it also determines the circle of business entities required to draw up the consolidated financial statements solely in accordance with international financial reporting standards.

Containment Modelling with the ASTEC Code

International Nuclear Information System (INIS)

Sadek, Sinisa; Grgic, Davor

2014-01-01

ASTEC is an integral computer code jointly developed by Institut de Radioprotection et de Surete Nucleaire (IRSN, France) and Gesellschaft fur Anlagen-und Reaktorsicherheit (GRS, Germany) to assess the nuclear power plant behaviour during a severe accident (SA). It consists of 13 coupled modules which compute various SA phenomena in primary and secondary circuits of the nuclear power plants (NPP), and in the containment. The ASTEC code was used to model and to simulate NPP behaviour during a postulated station blackout accident in the NPP Krsko, a two-loop pressurized water reactor (PWR) plant. The primary system of the plant was modelled with 110 thermal hydraulic (TH) volumes, 113 junctions and 128 heat structures. The secondary system was modelled with 76 TH volumes, 77 junctions and 87 heat structures. The containment was modelled with 10 TH volumes by taking into account containment representation as a set of distinctive compartments, connected with 23 junctions. A total of 79 heat structures were used to simulate outer containment walls and internal steel and concrete structures. Prior to the transient calculation, a steady state analysis was performed. In order to achieve correct plant initial conditions, the operation of regulation systems was modelled. Parameters which were subjected to regulation were the pressurizer pressure, the pressurizer narrow range level and steam mass flow rates in the steam lines. The accident analysis was focused on containment behaviour, however the complete integral NPP analysis was carried out in order to provide correct boundary conditions for the containment calculation. During the accident, the containment integrity was challenged by release of reactor system coolant through degraded coolant pump seals and, later in the accident following release of the corium out of the reactor pressure vessel, by the molten corium concrete interaction and direct containment heating mechanisms. Impact of those processes on relevant

Soft Regulators, though judges