The separation of radionuclide migration by solution and particle transport in LLRW repository buffer material

International Nuclear Information System (INIS)

Torok, J.; Buckley, L.P.; Woods, B.L.

1989-01-01

Laboratory-scale lysimeter experiments were performed with simulated waste forms placed in candidate buffer materials which have been chosen for a low-level radioactive waste repository. Radionuclide releases into the effluent water and radionuclide capture by the buffer material were determined. The results could not be explained by traditional solution transport mechanisms, and transport by particles released from the waste form and/or transport by buffer particles were suspected as the dominant mechanism for radionuclide release from the lysimeters. To elucidate the relative contribution of particle and solution transport, the waste forms were replaced by a wafer of neutron-activated buffer soaked with selected soluble isotopes. Particle transport was determined by the movement of gamma-emitting neutron-activation products through the lysimeter. Solution transport was quantified by comparing the migration of soluble radionuclides relative to the transport of neutron activation products. The new approach for monitoring radionuclide migration in soil is presented. It facilitates the determination of most of the fundamental coefficients required to model the transport process

Calorimetric and diffractometric evidence for the sequential crystallization of buffer components and the consequential pH swing in frozen solutions.

Science.gov (United States)

Sundaramurthi, Prakash; Shalaev, Evgenyi; Suryanarayanan, Raj

2010-04-15

Sequential crystallization of succinate buffer components in the frozen solution has been studied by differential scanning calorimetry and X-ray diffractometry (both laboratory and synchrotron sources). The consequential pH shifts were monitored using a low-temperature electrode. When a solution buffered to pH pK(a)(2), the freeze-concentrate pH first decreased and then increased due to the sequential crystallization of the basic (disodium succinate) followed by the acidic (monosodium succinate and succinic acid) buffer components. XRD provided direct evidence of the crystallization events in the frozen buffer solutions, including the formation of disodium succinate hexahydrate [Na(2)(CH(2)COO)(2).6H(2)O]. When the frozen solution was warmed in a differential scanning calorimeter, multiple endotherms attributable to the melting of buffer components and ice were observed. When the frozen solutions were dried under reduced pressure, ice sublimation was followed by dehydration of the crystalline hexahydrate to a poorly crystalline anhydrate. However, crystalline succinic acid and monosodium succinate were retained in the final lyophiles. The pH and the buffer salt concentration of the prelyo solution influenced the crystalline salt content in the final lyophile. The direction and magnitude of the pH shift in the frozen solution depended on both the initial pH and the buffer concentration. In light of the pH-sensitive nature of a significant fraction of pharmaceuticals (especially proteins), extreme care is needed in both the buffer selection and its concentration.

Buffer capacity of biologics--from buffer salts to buffering by antibodies.

Science.gov (United States)

Karow, Anne R; Bahrenburg, Sven; Garidel, Patrick

2013-01-01

Controlling pH is essential for a variety of biopharmaceutical process steps. The chemical stability of biologics such as monoclonal antibodies is pH-dependent and slightly acidic conditions are favorable for stability in a number of cases. Since control of pH is widely provided by added buffer salts, the current study summarizes the buffer characteristics of acetate, citrate, histidine, succinate, and phosphate buffers. Experimentally derived values largely coincide with values calculated from a model that had been proposed in 1922 by van Slyke. As high concentrated protein formulations become more and more prevalent for biologics, the self-buffering potential of proteins becomes of relevance. The current study provides information on buffer characteristics for pH ranges down to 4.0 and up to 8.0 and shows that a monoclonal antibody at 50 mg/mL exhibits similar buffer capacity as 6 mM citrate or 14 mM histidine (pH 5.0-6.0). Buffer capacity of antibody solutions scales linearly with protein concentration up to more than 200 mg/mL. At a protein concentration of 220 mg/mL, the buffer capacity resembles the buffer capacity of 30 mM citrate or 50 mM histidine (pH 5.0-6.0). The buffer capacity of monoclonal antibodies is practically identical at the process relevant temperatures 5, 25, and 40°C. Changes in ionic strength of ΔI=0.15, in contrast, can alter the buffer capacity up to 35%. In conclusion, due to efficient self-buffering by antibodies in the pH range of favored chemical stability, conventional buffer excipients could be dispensable for pH stabilization of high concentrated protein solutions. Copyright © 2013 American Institute of Chemical Engineers.

Buffer standards for the physiological pH of N-[2-hydroxy-1,1-bis(hydroxymethyl)ethyl]glycine (TRICINE) from T = (278.15 to 328.15) K

International Nuclear Information System (INIS)

Roy, Rabindra N.; Roy, Lakshmi N.; Henson, Isaac B.; Stegner, Jessica M.; Dinga, John J.; Summers, Clark E.; Suhrheinrich, Gregory L.; Veliz, Jaime A.; Dieterman, Lauren A.

2012-01-01

Highlights: ► This work reports pH values of TRICINE buffer. ► Liquid junction potential correct is applied. ► These values will be used by clinical and biomedical scientists. ► The pH values lie within 6.8 to 7.5. - Abstract: The pH values of two buffer solutions without NaCl and seven buffer solutions with added NaCl, having ionic strengths (I = 0.16 mol · kg −1 ) similar to those of physiological fluids, have been evaluated at 12 temperatures from T = (278.15 to 328.15) K by way of the extended form of the Debye–Hückel equation of the Bates–Guggenheim convention. The residual liquid junction potentials (δE j ) between the buffer solutions of TRICINE and saturated KCl solution of the calomel electrode at T = (298.15 and 310.15) K have been estimated by measurement with a flowing junction cell. For the buffer solutions with the molality of TRICINE(m 1 ) = 0.06 mol · kg −1 , NaTRICINE(m 2 ) = 0.02 mol · kg −1 , and NaCl(m 3 ) = 0.14 mol · kg −1 , the pH values at T = 310.15 K obtained from the extended Debye–Hückel equation and the inclusion of the liquid junction correction are 7.342 and 7.342, respectively. These are in excellent agreement. The zwitterionic buffer TRICINE is recommended as a secondary pH standard in the region for clinical application.

BIOKID: Randomized controlled trial comparing bicarbonate and lactate buffer in biocompatible peritoneal dialysis solutions in children [ISRCTN81137991

Directory of Open Access Journals (Sweden)

Misselwitz Joachim

2004-10-01

Full Text Available Abstract Background Peritoneal dialysis (PD is the preferred dialysis modality in children. Its major drawback is the limited technique survival due to infections and progressive ultrafiltration failure. Conventional PD solutions exert marked acute and chronic toxicity to local tissues. Prolonged exposure is associated with severe histopathological alterations including vasculopathy, neoangiogenesis, submesothelial fibrosis and a gradual loss of the mesothelial cell layer. Recently, more biocompatible PD solutions containing reduced amounts of toxic glucose degradation products (GDPs and buffered at neutral pH have been introduced into clinical practice. These solutions contain lactate, bicarbonate or a combination of both as buffer substance. Increasing evidence from clinical trials in adults and children suggests that the new PD fluids may allow for better long-term preservation of peritoneal morphology and function. However, the relative importance of the buffer in neutral-pH, low-GDP fluids is still unclear. In vitro, lactate is cytotoxic and vasoactive at the concentrations used in PD fluids. The BIOKID trial is designed to clarify the clinical significance of the buffer choice in biocompatible PD fluids. Methods/design The objective of the study is to test the hypothesis that bicarbonate based PD solutions may allow for a better preservation of peritoneal transport characteristics in children than solutions containing lactate buffer. Secondary objectives are to assess any impact of the buffer system on acid-base status, peritoneal tissue integrity and the incidence and severity of peritonitis. After a run-in period of 2 months during which a targeted cohort of 60 patients is treated with a conventional, lactate buffered, acidic, GDP containing PD fluid, patients will be stratified according to residual renal function and type of phosphate binding medication and randomized to receive either the lactate-containing Balance solution or the

BIOKID: randomized controlled trial comparing bicarbonate and lactate buffer in biocompatible peritoneal dialysis solutions in children [ISRCTN81137991].

Science.gov (United States)

Nau, Barbara; Schmitt, Claus P; Almeida, Margarida; Arbeiter, Klaus; Ardissino, Gianluigi; Bonzel, Klaus E; Edefonti, Alberto; Fischbach, Michel; Haluany, Karin; Misselwitz, Joachim; Kemper, Markus J; Rönnholm, Kai; Wygoda, Simone; Schaefer, Franz

2004-10-14

Peritoneal dialysis (PD) is the preferred dialysis modality in children. Its major drawback is the limited technique survival due to infections and progressive ultrafiltration failure. Conventional PD solutions exert marked acute and chronic toxicity to local tissues. Prolonged exposure is associated with severe histopathological alterations including vasculopathy, neoangiogenesis, submesothelial fibrosis and a gradual loss of the mesothelial cell layer. Recently, more biocompatible PD solutions containing reduced amounts of toxic glucose degradation products (GDPs) and buffered at neutral pH have been introduced into clinical practice. These solutions contain lactate, bicarbonate or a combination of both as buffer substance. Increasing evidence from clinical trials in adults and children suggests that the new PD fluids may allow for better long-term preservation of peritoneal morphology and function. However, the relative importance of the buffer in neutral-pH, low-GDP fluids is still unclear. In vitro, lactate is cytotoxic and vasoactive at the concentrations used in PD fluids. The BIOKID trial is designed to clarify the clinical significance of the buffer choice in biocompatible PD fluids. The objective of the study is to test the hypothesis that bicarbonate based PD solutions may allow for a better preservation of peritoneal transport characteristics in children than solutions containing lactate buffer. Secondary objectives are to assess any impact of the buffer system on acid-base status, peritoneal tissue integrity and the incidence and severity of peritonitis. After a run-in period of 2 months during which a targeted cohort of 60 patients is treated with a conventional, lactate buffered, acidic, GDP containing PD fluid, patients will be stratified according to residual renal function and type of phosphate binding medication and randomized to receive either the lactate-containing Balance solution or the bicarbonate-buffered Bicavera solution for a period of

Unusual buffer action of free-standing nanoscopically confined water.

Science.gov (United States)

Liao, Kylin; Xu, Xiaozhou; Du, Xuezhong

2010-01-15

The acid-base properties of nanoscopic water confined in the black soap films (BSFs), which were prepared from aqueous solutions of sodium dodecylsulphate (SDS) with the dye neutral red (NR) as a pH probe, were investigated using a combination of UV-vis and FTIR spectroscopy. For the SDS micellar solutions at pH 1.0-9.5 adjusted with HCl/NaOH solutions and at pH 9.4 with ammonium buffered solution, the aqueous core thicknesses in the corresponding BSFs ranged from 2.7 to 6.2 nm, and the nanoscopically confined water exhibits unusual buffer action resistant not only to acidic/alkaline solutions but also to standard buffer solution. In the heavily water-depleted confined zones, it is most likely that charge pairs in proton-transfer reactions could not be formed effectively and proton transfer was prohibited in the absence of sufficient solvating ability. Theoretical analyzes indicated that the buffer action of the nanoscopic water originated from the confinement effect of two charged surfaces of the BSFs. These results might inspire deeper understanding and further studies of biobuffering, enzyme superactivity, acid-catalyzed reactions, and Nafion fuel cell membranes.

Scientific Approach and Inquiry Learning Model in the Topic of Buffer Solution: A Content Analysis

Science.gov (United States)

Kusumaningrum, I. A.; Ashadi, A.; Indriyanti, N. Y.

2017-09-01

Many concepts in buffer solution cause student’s misconception. Understanding science concepts should apply the scientific approach. One of learning models which is suitable with this approach is inquiry. Content analysis was used to determine textbook compatibility with scientific approach and inquiry learning model in the concept of buffer solution. By using scientific indicator tools (SIT) and Inquiry indicator tools (IIT), we analyzed three chemistry textbooks grade 11 of senior high school labeled as P, Q, and R. We described how textbook compatibility with scientific approach and inquiry learning model in the concept of buffer solution. The results show that textbook P and Q were very poor and book R was sufficient because the textbook still in procedural level. Chemistry textbooks used at school are needed to be improved in term of scientific approach and inquiry learning model. The result of these analyses might be of interest in order to write future potential textbooks.

Microchannel electrokinetics of charged analytes in buffered solutions near floating electrodes

DEFF Research Database (Denmark)

Andersen, Mathias Bækbo; Wolfcale, Trevor; Gregersen, Misha Marie

to accurately predict such behavior in these flow regimes. Experimentally, using conventional fluorescence microscopy, we investigated the concentration gradient (as well as the associated electroosmosis, induced-charge electro-osmosis, and electrophoresis) of the charged analyte near the floating electrode......We present both experimental and numerical studies of nonlinear electrokinetic flow of buffered solutions seeded with dilute analytes in a straight microchannel (0.6 μm high, 250 μm wide, and 9000 μm long) with a 0.15 μm high 60 μm wide electrode situated at the bottom center of the channel...... as a function of analyte (1 to 10 μM fluorescein and bodipy) and buffer (1 to 10 mM borate and posphate) concentrations and an externally applied voltage drop (50 to 100 V) along the channel. We have implemented a nonlinear continuum kinetics model of the system involving the electric potential, the buffer flow...

Bias in the absorption coefficient determination of a fluorescent dye, standard reference material 1932 fluorescein solution

International Nuclear Information System (INIS)

DeRose, Paul C.; Kramer, Gary W.

2005-01-01

The absorption coefficient of standard reference material[registered] (SRM[registered]) 1932, fluorescein in a borate buffer solution (pH=9.5) has been determined at λ=488.0, 490.0, 490.5 and 491.0 nm using the US national reference UV/visible spectrophotometer. The purity of the fluorescein was determined to be 97.6% as part of the certification of SRM 1932. The solution measured was prepared gravimetrically by diluting SRM 1932 with additional borate buffer. The value of the absorption coefficient was corrected for bias due to fluorescence that reaches the detector and for dye purity. Bias due to fluorescence was found to be on the order of -1% for both monochromatic and polychromatic (e.g., diode-array based) spectrophotometers

THE KINETICS OF SAPONIFICATION OF IODOACETIC ACID BY SODIUM HYDROXIDE AND BY CERTAIN ALKALINE BUFFER SOLUTIONS.

Science.gov (United States)

Brdicka, R

1936-07-20

1. The rate of the saponification of iodoacetic acid in sodium hydroxide and alkaline buffer solutions yielding glycollic acid was measured by means of Heyrovský's polarographic method. 2. From the bimolecular velocity constants, increasing with the ionic strength of the solution, the Brönsted factor, F, which characterizes the primary salt effect, was calculated. 3. In the borate buffer solutions the monomolecular constants of the saponification were determined which, at values above the pH of neutralization of boric acid, show a proportionality to the concentration of hydroxyl anions. Below the pH of neutralization of boric acid, they are proportional to the concentration of borate anions.

Sulfate influx on band 3 protein of equine erythrocyte membrane (Equus caballus) using different experimental temperatures and buffer solutions.

Science.gov (United States)

Casella, S; Piccione, D; Ielati, S; Bocchino, E G; Piccione, G

2013-06-01

The aim of this study was to assess the anion transport in equine erythrocytes through the measurement of the sulfate uptake operating from band 3 using different experimental temperatures and buffer solutions. Blood samples of six clinically healthy horses were collected via jugular vein puncture, and an emochrome-citometric examination was performed. The blood was divided into four aliquots and by centrifugation and aspiration the plasma and buffy coat were carefully discarded. The red blood cells were washed with an isosmotic medium and centrifuged. The obtained cell suspensions were incubated with two different experimental buffer solutions (buffer A: 115 mM Na2SO4, 10 mM NaCl, 20 mM ethylenediaminetetraacetic acid, 30 mM glucose; and buffer B: 115 mM Na2SO4, 10 mM NaCl, 20 mM ethylenediaminetetraacetic acid, 30 mM MgCl2) in a water bath for 1 h at 25 °C and 37 °C. Normal erythrocytes, suspended at 3% hematocrit, were used to measure the SO4= influx by absorption spectrophotometry at 425 nm wavelength. Unpaired Student's t-test showed a statistically significant decrease (P buffer solutions. Comparing the buffer A with buffer B unpaired Student's t-test showed statistically lower values (P < 0.0001) for A solution versus B solution both at 25 °C and at 37 °C. The greater inhibition of SO4 (=) influx measured in equine erythrocytes indicates the increased formation of the sulfydryl bonds in band 3 and the modulation of the sulfydryl groups, culminating in the conformational changes in band 3. Copyright © 2012 John Wiley & Sons, Ltd.

Simple solution-processed CuOX as anode buffer layer for efficient organic solar cells

International Nuclear Information System (INIS)

Shen, Wenfei; Yang, Chunpeng; Bao, Xichang; Sun, Liang; Wang, Ning; Tang, Jianguo; Chen, Weichao; Yang, Renqiang

2015-01-01

Graphical abstract: - Highlights: • Simple solution-processed CuO X hole transport layer for efficient organic solar cell. • Good photovoltaic performances as hole transport layer in OSCs with P3HT and PBDTTT-C as donor materials. • The device with CuO X as hole transport layer shows great improved stability compared with that of device with PEDOT:PSS as hole transport layer. - Abstract: A simple, solution-processed ultrathin CuO X anode buffer layer was fabricated for high performance organic solar cells (OSCs). XPS measurement demonstrated that the CuO X was the composite of CuO and Cu 2 O. The CuO X modified ITO glass exhibit a better surface contact with the active layer. The photovoltaic performance of the devices with CuO X layer was optimized by varying the thickness of CuO X films through changing solution concentration. With P3HT:PC 61 BM as the active layer, we demonstrated an enhanced PCE of 4.14% with CuO X anode buffer layer, compared with that of PEDOT:PSS layer. The CuO X layer also exhibits efficient photovoltaic performance in devices with PBDTTT-C:PC 71 BM as the active layer. The long-term stability of CuO X device is better than that of PEDOT:PSS device. The results indicate that the easy solution-processed CuO X film can act as an efficient anode buffer layer for high-efficiency OSCs

Stability of biodegradable waterborne polyurethane films in buffered saline solutions.

Science.gov (United States)

Lin, Ying Yi; Hung, Kun-Che; Hsu, Shan-Hui

2015-09-21

The stability of polyurethane (PU) is of critical importance for applications such as in coating industry or as biomaterials. To eliminate the environmental concerns on the synthesis of PU which involves the use of organic solvents, the aqueous-based or waterborne PU (WBPU) has been developed. WBPU, however, may be unstable in an electrolyte-rich environment. In this study, the authors reported the stability of biodegradable WBPU in the buffered saline solutions evaluated by atomic force microscopy (AFM). Various biodegradable WBPU films were prepared by spin coating on coverslip glass, with a thickness of ∼300 nm. The surface AFM images of poly(ε-caprolactone) (PCL) diol-based WBPU revealed nanoglobular structure. The same feature was observed when 20% molar of the PCL diol soft segment was replaced by polyethylene butylenes adipate diol. After hydration in buffered saline solutions for 24 h, the surface domains generally increased in sizes and became irregular in shape. On the other hand, when the soft segment was replaced by 20% poly(l-lactide) diol, a meshlike surface structure was demonstrated by AFM. When the latter WBPU was hydrated, the surface domains appeared to be disconnected. Results from the attenuated total reflectance infrared spectroscopy and x-ray photoelectron spectroscopy indicated that the surface chemistry of WBPU films was altered after hydration. These changes were probably associated with the neutralization of carboxylate by ions in the saline solutions, resulting in the rearrangements of soft and hard segments and causing instability of the WBPU.

Buffered lidocaine and bupivacaine mixture - the ideal local anesthetic solution?

Science.gov (United States)

Best, Corliss A; Best, Alyssa A; Best, Timothy J; Hamilton, Danielle A

2015-01-01

The use of injectable local anesthetic solutions to facilitate pain-free surgery is an integral component of many procedures performed by the plastic surgeon. In many instances, a solution that has both rapid onset and prolonged duration of analgesia is optimal. A combination of lidocaine and bupivacaine, plain or with epinephrine, is readily available in most Canadian health care settings where such procedures are performed, and fulfills these criteria. However, commercially available solutions of both medications are acidic and cause a burning sensation on injection. Buffering to neutral pH with sodium bicarbonate is a practical method to mitigate the burning sensation, and has the added benefit of increasing the fraction of nonionized lipid soluble drug available. The authors report on the proportions of the three drugs to yield a neutral pH, and the results of an initial survey regarding the use of the combined solution with epinephrine in hand surgery.

Chemical degradation of 3H-labeled substance P in tris buffer solution

International Nuclear Information System (INIS)

Higa, T.; Desiderio, D.M.

1988-01-01

Substance P (SP) is an important neuropeptide that has been implicated in several physiological processes, and it is necessary to devise an analytical procedure to measure endogenous SP with a combination of high sensitivity and maximum molecular specificity. However, the unique chemical nature of SP (polarity, chemical stability, ease of oxidation, peptide bond lability) plays a significant role in its analysis, such as in receptor assays, immunoassays, chromatography, and mass spectrometry. In this study, we evaluated in polypropylene and glass assay tubes the effects on the recovery and stability of tritiated SP ([3H]SP) of several pertinent experimental parameters such as buffer, pH, multiple freeze-thaw cycles, and incubation temperature and time. Bovine serum albumin (BSA) effectively reduced the absorption of [3H]SP to polypropylene and glass tube surfaces. Following multiple (6X) freeze-thaw cycles of solutions in BSA-precoated tubes, the recovery of radioactive [3H]SP remained high (greater than 75%) after the last cycle, whereas recovery was minimal in uncoated or siliconized glass tubes. A high level of radioactivity recovery was maintained for 14 days of storage of [3H]SP in triethylamine formate (TEAF) solution in BSA-precoated tubes at 4 and -20 degrees C, but decreased at 37 degrees C to less than 80% in only 3 h. Following storage in Tris-HCl (pH 7.4) buffer, a combination of HPLC and mass spectrometric analyses revealed that a significant amount of peptide bond cleavage occurred to produce the two peptides ArgProLys (RPK) and ArgProLysProGlnGln (RPKPQQ), with only a small amount of remaining intact SP. That decomposition was not observed in triethylamine formate TEAF (pH 3.14) buffer solutions

Natural dissolved organic matter mobilizes Cd but does not affect the Cd uptake by the green algae Pseudokirchneriella subcapitata (Korschikov) in resin buffered solutions

Energy Technology Data Exchange (ETDEWEB)

Verheyen, Liesbeth, E-mail: verheyenliesbeth@gmail.com; Versieren, Liske, E-mail: liske.versieren@ees.kuleuven.be; Smolders, Erik, E-mail: erik.smolders@ees.kuleuven.be

2014-09-15

Highlights: • Different DOM samples were added to solutions with a resin buffered Cd{sup 2+} activity. • This increased total dissolved Cd by factors 3–16 due to complexation reactions. • Cd uptake in algae was unaffected or increased maximally 1.6 fold upon addition. • Free Cd{sup 2+} is the main bioavailable form of Cd for algae in well buffered solutions. - Abstract: Natural dissolved organic matter (DOM) can have contrasting effects on metal bioaccumulation in algae because of complexation reactions that reduce free metal ion concentrations and because of DOM adsorption to algal surfaces which promote metal adsorption. This study was set up to reveal the role of different natural DOM samples on cadmium (Cd) uptake by the green algae Pseudokirchneriella subcapitata (Korschikov). Six different DOM samples were collected from natural freshwater systems and isolated by reverse osmosis. In addition, one {sup 13}C enriched DOM sample was isolated from soil to trace DOM adsorption to algae. Algae were exposed to standardized solutions with or without these DOM samples, each exposed at equal DOM concentrations and at equal non-toxic Cd{sup 2+} activity (∼4 nM) that was buffered with a resin. The DOM increased total dissolved Cd by factors 3–16 due to complexation reactions at equal Cd{sup 2+} activity. In contrast, the Cd uptake was unaffected by DOM or increased maximally 1.6 fold ({sup 13}C enriched DOM). The {sup 13}C analysis revealed that maximally 6% of algal C was derived from DOM and that this can explain the small increase in biomass Cd. It is concluded that free Cd{sup 2+} and not DOM-complexed Cd is the main bioavailable form of Cd when solution Cd{sup 2+} is well buffered.

Electrochemical impedance study of copper in phosphate buffered solution

International Nuclear Information System (INIS)

Salimon, J.; Mohamad, M.; Yamin, B.M.; Kalaji, M.

2003-01-01

The processes occurring on the copper electrode surface in phosphate buffered solution were investigated using the Electrochemical Impedance Spectroscopy. The electrochemical behaviors of copper through their charge transfer resistance and double-layer capacitance at the onset of the hydrogen evolution region and the anodic passivation layer formation and diffusion of copper species at anodic potential regions are discussed. The specific adsorption of anions (hydroxide and/or H/sub 2/PO/sub 4/) occurred at potential less negative than -0.9V. Adsorbed hydrogen appeared at hydrogen evolution region at potential range of -1.5 to -1.0 V. The deposition of insoluble copper species occurred at anodic potential regions. (author)

Thermodynamic stability of radioactivity standard solutions

International Nuclear Information System (INIS)

Iroulard, M.G.

2007-04-01

The basic requirement when preparing radioactivity standard solutions is to guarantee the concentration of a radionuclide or a radioelement, expressed in the form of activity concentration (Ac = A/m (Bq/g), with A: activity and m: mass of solution). Knowledge of the law of radioactive decay and the half-life of a radionuclide or radioelement makes it possible to determine the activity concentration at any time, and this must be confirmed subsequently by measurement. Furthermore, when radioactivity standard solutions are prepared, it is necessary to establish optimal conditions of thermodynamic stability of the standard solutions. Radioactivity standard solutions are prepared by metrology laboratories from original solutions obtained from a range of suppliers. These radioactivity standard solutions must enable preparation of liquid and/or solid radioactivity standard sources of which measurement by different methods can determine, at a given instant, the activity concentration of the radionuclide or radioelement present in the solution. There are a number of constraints associated with the preparation of such sources. Here only those that relate to the physical and chemical properties of the standard solution are considered, and therefore need to be taken into account when preparing a radioactivity standard solution. These issues are considered in this document in accordance with the following plan: - A first part devoted to the chemical properties of the solutions: - the solubilization media: ultra-pure water and acid media, - the carriers: concentration, oxidation state of the radioactive element and the carrier element. - A second part describing the methodology of the preparation, packaging and storage of standard solutions: - glass ampoules: the structure of glasses, the mechanisms of their dissolution, the sorption phenomenon at the solid-solution interface, - quartz ampoules, - cleaning and packaging: cleaning solutions, internal surface coatings and

Thermodynamic stability of radioactivity standard solutions

Energy Technology Data Exchange (ETDEWEB)

Iroulard, M.G

2007-04-15

The basic requirement when preparing radioactivity standard solutions is to guarantee the concentration of a radionuclide or a radioelement, expressed in the form of activity concentration (Ac = A/m (Bq/g), with A: activity and m: mass of solution). Knowledge of the law of radioactive decay and the half-life of a radionuclide or radioelement makes it possible to determine the activity concentration at any time, and this must be confirmed subsequently by measurement. Furthermore, when radioactivity standard solutions are prepared, it is necessary to establish optimal conditions of thermodynamic stability of the standard solutions. Radioactivity standard solutions are prepared by metrology laboratories from original solutions obtained from a range of suppliers. These radioactivity standard solutions must enable preparation of liquid and/or solid radioactivity standard sources of which measurement by different methods can determine, at a given instant, the activity concentration of the radionuclide or radioelement present in the solution. There are a number of constraints associated with the preparation of such sources. Here only those that relate to the physical and chemical properties of the standard solution are considered, and therefore need to be taken into account when preparing a radioactivity standard solution. These issues are considered in this document in accordance with the following plan: - A first part devoted to the chemical properties of the solutions: - the solubilization media: ultra-pure water and acid media, - the carriers: concentration, oxidation state of the radioactive element and the carrier element. - A second part describing the methodology of the preparation, packaging and storage of standard solutions: - glass ampoules: the structure of glasses, the mechanisms of their dissolution, the sorption phenomenon at the solid-solution interface, - quartz ampoules, - cleaning and packaging: cleaning solutions, internal surface coatings and

Electrochemical investigation of mineral electrodes in phosphate-buffered alkaline solution

Directory of Open Access Journals (Sweden)

D Erdenechimeg

2014-12-01

Full Text Available Cyclic voltammetric methods have been applied to study the electrochemical behavior of the sulfide minerals in phosphate-buffered alkaline solution. The redox process of electrodes of sulfide ores was investigated using silicone-impregnated graphite electrode. The cathodic and anodic reaction products in alkaline solution were determined within the potential range of -2V to +2V (vs. Ag/AgCl. The several successive measurement cycles’ voltammograms leads to the appearance of a new anodic peak at E = 450mV, which is absent in the first cycle and curves, as well as other features that appear in cycling, can probably be explained by secondary electrochemical transformations of the products formed by the oxidation of the original pyrite at the interface between the electrode material.DOI: http://doi.dx.org/10.5564/mjc.v15i0.318 Mongolian Journal of Chemistry 15 (41, 2014, p33-35

Simple solution-processed CuO{sub X} as anode buffer layer for efficient organic solar cells

Energy Technology Data Exchange (ETDEWEB)

Shen, Wenfei [CAS Key Laboratory of Bio-based Materials, Qingdao Institute of Bioenergy and Bioprocess Technology, Chinese Academy of Sciences, 189 Songling Road, Qingdao 266101 (China); Institute of Hybrid Materials, The Growing Base for State Key Laboratory, Qingdao University, 308 Ningxia Road, Qingdao 266071 (China); Yang, Chunpeng [CAS Key Laboratory of Bio-based Materials, Qingdao Institute of Bioenergy and Bioprocess Technology, Chinese Academy of Sciences, 189 Songling Road, Qingdao 266101 (China); Bao, Xichang, E-mail: baoxc@qibebt.ac.cn [CAS Key Laboratory of Bio-based Materials, Qingdao Institute of Bioenergy and Bioprocess Technology, Chinese Academy of Sciences, 189 Songling Road, Qingdao 266101 (China); Sun, Liang; Wang, Ning [CAS Key Laboratory of Bio-based Materials, Qingdao Institute of Bioenergy and Bioprocess Technology, Chinese Academy of Sciences, 189 Songling Road, Qingdao 266101 (China); Tang, Jianguo [Institute of Hybrid Materials, The Growing Base for State Key Laboratory, Qingdao University, 308 Ningxia Road, Qingdao 266071 (China); Chen, Weichao [CAS Key Laboratory of Bio-based Materials, Qingdao Institute of Bioenergy and Bioprocess Technology, Chinese Academy of Sciences, 189 Songling Road, Qingdao 266101 (China); Yang, Renqiang, E-mail: yangrq@qibebt.ac.cn [CAS Key Laboratory of Bio-based Materials, Qingdao Institute of Bioenergy and Bioprocess Technology, Chinese Academy of Sciences, 189 Songling Road, Qingdao 266101 (China)

2015-10-15

Graphical abstract: - Highlights: • Simple solution-processed CuO{sub X} hole transport layer for efficient organic solar cell. • Good photovoltaic performances as hole transport layer in OSCs with P3HT and PBDTTT-C as donor materials. • The device with CuO{sub X} as hole transport layer shows great improved stability compared with that of device with PEDOT:PSS as hole transport layer. - Abstract: A simple, solution-processed ultrathin CuO{sub X} anode buffer layer was fabricated for high performance organic solar cells (OSCs). XPS measurement demonstrated that the CuO{sub X} was the composite of CuO and Cu{sub 2}O. The CuO{sub X} modified ITO glass exhibit a better surface contact with the active layer. The photovoltaic performance of the devices with CuO{sub X} layer was optimized by varying the thickness of CuO{sub X} films through changing solution concentration. With P3HT:PC{sub 61}BM as the active layer, we demonstrated an enhanced PCE of 4.14% with CuO{sub X} anode buffer layer, compared with that of PEDOT:PSS layer. The CuO{sub X} layer also exhibits efficient photovoltaic performance in devices with PBDTTT-C:PC{sub 71}BM as the active layer. The long-term stability of CuO{sub X} device is better than that of PEDOT:PSS device. The results indicate that the easy solution-processed CuO{sub X} film can act as an efficient anode buffer layer for high-efficiency OSCs.

Limitations when use chloramphenicol-bcyclodextrins complexes in ophtalmic solutions buffered with boric acid/borax system

Directory of Open Access Journals (Sweden)

Todoran Nicoleta

2014-12-01

Full Text Available Chloramphenicol eye drops are commonly prescribed in concentrations of 0.5-1% in the treatment of infectious conjunctivitis. In terms of ophthalmic solution preparation, the major disadvantage of chloramphenicol consists in its low solubility in water. The solubility is increased by substances that form chloramphenicol-complexes, for example: boric acid/borax or cyclodextrins. Objective: Experimental studies aimed to evaluate the potential advantages of enhancing the solubility and stability of chloramphenicol (API by molecular encapsulation in b-cyclodextrin (CD, in formulation of ophthalmic solutions buffered with boric acid/borax system. Methods and Results: We prepared four APIb- CD complexes, using two methods (kneading and co-precipitation and two molar ratio of API/b-cyclodextrin (1:1 and 1:2. The formation of complexes was proved by differential scanning calorimetry (DSC and the in vitro dissolution tests. Using these compounds, we prepared eight ophthalmic solutions, formulated in two variants of chloramphenicol concentrations (0.4% and 0.5%. Each solution was analyzed, by the official methods, at preparation and periodically during three months of storing in different temperature conditions (4°C, 20°C and 30°C. Conclusions: Inclusion of chloramphenicol in b-cyclodextrin only partially solves the difficulties due to the low solubility of chloramphenicol. The protection of chloramphenicol molecules is not completely ensured when the ophthalmic solutions are buffered with the boric acid/borax system.

Buffer Sizing in Wireless Networks: Challenges, Solutions, and Opportunities

KAUST Repository

Showail, Ahmad

2016-04-01

Buffer sizing is an important network configuration parameter that impacts the Quality of Service (QoS) characteristics of data traffic. With falling memory costs and the fallacy that \\'more is better\\', network devices are being overprovisioned with large bu ers. This may increase queueing delays experienced by a packet and subsequently impact stability of core protocols such as TCP. The problem has been studied extensively for wired networks. However, there is little work addressing the unique challenges of wireless environment such as time-varying channel capacity, variable packet inter-service time, and packet aggregation, among others. In this paper we discuss these challenges, classify the current state-of-the-art solutions, discuss their limitations, and provide directions for future research in the area.

On the Electrochemical Behavior of PVD Ti-Coated AISI 304 Stainless Steel in Borate Buffer Solution

Science.gov (United States)

Fattah-alhosseini, Arash; Elmkhah, Hassan; Attarzadeh, Farid Reza

2017-04-01

This work aims at studying the electrochemical behavior of annealed pure titanium (Ti) and nano-structured (NS) Ti coating in borate buffer solutions. Cathodic arc evaporation was successfully applied to deposit NS Ti coating. Samples were characterized by means of scanning electron microscope and x-ray diffraction. Potentiodynamic polarization tests, electrochemical impedance spectroscopy, and Mott-Schottky analysis were employed to discuss the electrochemical behavior of samples thoroughly. Electrochemical measurements showed that the deposited NS Ti coating offers a superior passivity in borate buffer solutions of pH 9.0 and 9.5. Mott-Schottky analysis revealed that all passive films are of n-type semiconducting nature in these alkaline solutions and the deposition process did not alter the semiconducting type of passive films formed on samples. Additionally, this analysis showed that the NS Ti coating possessed lower levels of donor densities. Finally, all electrochemical tests showed that passive behavior of the NS Ti samples was superior, mainly due to the formation of thicker and less defective passive films.

Physical Compatibility of Magnesium Sulfate and Sodium Bicarbonate in a Pharmacy-compounded Bicarbonate-buffered Hemofiltration Solution

Science.gov (United States)

Moriyama, Brad; Henning, Stacey A.; Jin, Haksong; Kolf, Mike; Rehak, Nadja N.; Danner, Robert L.; Walsh, Thomas J.; Grimes, George J.

2011-01-01

PURPOSE To assess the physical compatibility of magnesium sulfate and sodium bicarbonate in a pharmacy-compounded bicarbonate-buffered hemofiltration solution used at the National Institutes of Health Clinical Center (http://www.cc.nih.gov). METHODS Two hemofiltration fluid formulations with a bicarbonate of 50 mEq/L and a magnesium of 1.5 mEq/L or 15 mEq/L were prepared in triplicate with an automated compounding device. The hemofiltration solution with a bicarbonate of 50 mEq/L and a magnesium of 1.5 mEq/L contains the maximum concentration of additives that we use in clinical practice. The hemofiltration solution of 15 mEq/L of magnesium and 50 mEq/L of bicarbonate was used to study the physicochemical properties of this interaction. The solutions were stored without light protection at 22 to 25 °C for 48 hours. Physical compatibility was assessed by visual inspection and microscopy. The pH of the solutions was assayed at 3 to 4 hours and 52 to 53 hours after compounding. In addition, electrolyte and glucose concentrations in the solutions were assayed at two time points after preparation: 3 to 4 hours and 50 to 51 hours. RESULTS No particulate matter was observed by visual and microscopic inspection in the compounded hemofiltration solutions at 48 hours. Electrolyte and glucose concentrations and pH were similar at both time points after solution preparation. CONCLUSION Magnesium sulfate (1.5 mEq/L) and sodium bicarbonate (50 mEq/L) were physically compatible in a pharmacy-compounded bicarbonate-buffered hemofiltration solution at room temperature without light protection at 48 hours. PMID:20237384

Interaction of HEPES buffer with glass-ceramic scaffold: Can HEPES replace TRIS in SBF?

Science.gov (United States)

Rohanová, Dana; Horkavcová, Diana; Paidere, Laine; Boccaccini, Aldo Roberto; Bozděchová, Pavlína; Bezdička, Petr

2018-01-01

An international standard (ISO: 23317:2014) exists for the in vitro testing of inorganic biomaterials in simulated body fluid (SBF). This standard uses TRIS buffer to maintain neutral pH in SBF, but in our previous paper, we showed that the interaction of a tested glass-ceramic material with TRIS can produce false-positive results. In this study, we evaluated whether the HEPES buffer, which also belongs to the group of Good´s buffers, would be more suitable for SBF. We compared its suitability in two media: SBF with HEPES and demineralized water with HEPES. The tested scaffold (45S5 bioactive glass-based) was exposed to the media under a static-dynamic arrangement (solutions were replaced on a daily basis) for 15 days. Leachate samples were collected daily for the analysis of Ca 2+ ions and Si (AAS), (PO 4 ) 3- ions (UV-VIS), and to measure pH. The glass-ceramic scaffold was analyzed by SEM/EDS, XRD, and WD-XRF before and after 0.3, 1, 3, 7, 11, and 15 days of exposure. Our results confirmed the rapid selective dissolution of the glass-ceramic crystalline phase (Combeite) containing Ca 2+ ions due to the presence of HEPES, hydroxyapatite supersaturation being reached within 24 h in both solutions. These new results suggest that, like TRIS, HEPES buffer is not suitable for the in vitro testing of highly reactive inorganic biomaterials (glass, glass-ceramics). The ISO standard for such tests requires revision, but HEPES is not a viable alternative to TRIS buffer. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 106B: 143-152, 2018. © 2016 Wiley Periodicals, Inc.

Sm-doped CeO2 single buffer layer for YBCO coated conductors by polymer assisted chemical solution deposition (PACSD) method

International Nuclear Information System (INIS)

Li, G.; Pu, M.H.; Sun, R.P.; Wang, W.T.; Wu, W.; Zhang, X.; Yang, Y.; Cheng, C.H.; Zhao, Y.

2008-01-01

An over 150 nm thick Sm 0.2 Ce 0.8 O 1.9-x (SCO) single buffer layer has been deposited on bi-axially textured NiW (2 0 0) alloy substrate. Highly in-plane and out-of-plane oriented, dense, smooth and crack free SCO single layer has been obtained via a polymer-assisted chemical solution deposition (PACSD) approach. YBCO thin film has been deposited equally via a PACSD route on the SCO-buffered NiW, the as grown YBCO yielding a sharp transition at T c0 = 87 K as well as J c (0 T, 77 K) ∼ 1 MA/cm 2 . These results indicates that RE (lanthanides other than Ce) doping may be an effective approach to improve the critical thickness of solution derived CeO 2 film, which renders it a promising candidate as single buffer layer for YBCO coated conductors

Substituted benzotriazoles as inhibitors of copper corrosion in borate buffer solutions

Science.gov (United States)

Agafonkina, M. O.; Andreeva, N. P.; Kuznetsov, Yu. I.; Timashev, S. F.

2017-08-01

The adsorption of substituted 1,2,3-benzotriazoles (R-BTAs) onto copper is measured via ellipsometry in a pure borate buffer (pH 7.4) and satisfactorily described by Temkin's isotherm. The adsorption free energy (-Δ G a 0 ) values of these azoles are determined. The (-Δ G a 0 ) values are found to rise as their hydrophobicity, characterized by the logarithm of the partition coefficient of a substituted BTA in a model octanol-water system (log P), grows. The minimum concentration sufficient for the spontaneous passivation of copper ( C min) and a shift in the potential of local copper depassivation with chlorides ( E pt) after an azole is added to the solution (i.e., Δ E = E pt in - E pt backgr characterizing the ability of its adsorption to stabilize passivation) are determined in the same solution containing a corrosion additive (0.01M NaCl) for each azole under study. Both criteria of the passivating properties of azoles (log C min and Δ E) are shown to correlate linearly with log P, testifying to the role played by surface activity of this family of organic inhibitors in protecting copper in an aqueous solution.

Effect of Buffers on Aqueous Solute-Exclusion Zones around Ion-Exchange Resins

Science.gov (United States)

Zheng, Jian-ming; Wexler, Adam

2009-01-01

Interaction between charged surfaces in aqueous solution is a fundamental feature of colloid science. Theoretically, surface potential falls to half its value at a distance equal to a Debye length, which is typically on the order of tens to hundreds of nanometers. This potential prevents colloids from aggregating. On the other hand, long-range surface effects have been frequently reported. Here we report additional long-range effects. We find that charged latex particles in buffer solutions are uniformly excluded from several-hundred-micron-thick shells surrounding ion-exchange beads. Exclusion is observed whether the beads are charged similarly or oppositely to the particles. Hence, electrostatic interactions between bead and microsphere do not cause particle exclusion. Rather, exclusion may be the consequence of water molecules re-orienting to produce a more ordered structure, which then excludes the particles. PMID:19185312

Stable Inverted Low-Bandgap Polymer Solar Cells with Aqueous Solution Processed Low-Temperature ZnO Buffer Layers

Directory of Open Access Journals (Sweden)

Chunfu Zhang

2016-01-01

Full Text Available Efficient inverted low-bandgap polymer solar cells with an aqueous solution processed low-temperature ZnO buffer layer have been investigated. The low-bandgap material PTB-7 is employed so that more solar light can be efficiently harvested, and the aqueous solution processed ZnO electron transport buffer layer is prepared at 150°C so that it can be compatible with the roll-to-roll process. Power conversion efficiency (PCE of the inverted device reaches 7.12%, which is near the control conventional device. More importantly, the inverted device shows a better stability, keeping more than 90% of its original PCE after being stored for 625 hours, while PCE of the conventional device is only 75% of what it was. In addition, it is found that the ZnO thin film annealed in N2 can obviously increase PCE of the inverted device further to 7.26%.

[Prediction of common buffer catalysis in hydrolysis of fenchlorazole-ethyl].

Science.gov (United States)

Lin, Jing; Chen, Jing-wen; Zhang, Si-yu; Cai, Xi-yun; Qiao, Xian-liang

2008-09-01

The purpose of this study was to elucidate the effects of temperatures, pH levels and buffer catalysis on the hydrolysis of FCE. The hydrolysis of FCE follows first-order kinetics at different pH levels and temperatures. FCE hydrolysis rates are greatly increased at elevated pH levels and temperatures. The maximum contribution of buffer catalysis to the hydrolysis of FCE was assessed based on application of the Bronsted equations for general acid-base catalysis. The results suggest that the buffer solutions play an obvious catalysis role in hydrolysis of FCE and the hydrolysis rates of FCE are quickened by the buffer solutions. Besides, the buffer catalysis capacity of different buffer solutions is diverse, and the buffer catalysis capacity at different pH levels with the same buffer solutions is different, too. The phosphate buffer at pH = 7 shows the maximal buffer catalysis capacity. The hydrolysis rate constants of FCE as a function of temperature and pH, which were remedied by the buffer catalysis factor, were mathematically combined to predict the hydrolytic dissipation of FCE. The equation suggests that the hydrolysis half-lives of FCE ranged from 7 d to 790 d. Hydrolysis metabolites of FCE were identified by liquid chromatography-mass spectrometry. In basic conditions (pH 8-10), fenchlorazole was formed via breakdown of the ester bond of the safener.

The buffering-out effect and phase separation in aqueous solutions of EPPS buffer with 1-propanol, 2-propanol, or 2-methyl-2-propanol at T = 298.15 K

International Nuclear Information System (INIS)

Taha, Mohamed; Teng, Han-Lan; Lee, Ming-Jer

2012-01-01

Highlights: ► Buffering-out is a new liquid–liquid phase separation containing biological buffer. ► EPPS buffer-induced phase separation of aqueous solutions of aliphatic alcohols. ► Phase diagrams of EPPS + water + 1-propanol/2-propanol/2-methyl-2-propanol are studied. ► EPPS breaks the 1-propanol + water and 2-methyl-2-propanol + water azeotropes. ► The (liquid + liquid) equilibria can be well correlated by the NRTL model. - Abstract: Buffering-out is a new liquid–liquid phase separation phenomenon observed in mixtures containing a buffer as a mass separating agent. The (liquid + liquid) equilibrium (LLE) and (solid + liquid + liquid) equilibrium (SLLE) data were measured for the ternary systems {3-[4-(2-hydroxyethyl)piperazin-1-yl]propanesulfonic acid (EPPS) buffer + 1-propanol, 2-propanol, or 2-methyl-2-propanol + water} at T = 298.15 K under atmospheric pressure. The phase boundary data were fitted to an empirical equation relating to the concentrations of organic solvent and buffer. The effective excluded volume (EEV) values of EPPS were obtained from the phase boundary data. The phase-separation abilities of the investigated aliphatic alcohols were discussed. The reliability of the experimental tie-lines was satisfactorily confirmed by the Othmer–Tobias correlation. The experimental tie-lines data for the ternary systems have been correlated using the NRTL activity coefficient model. The separation of these aliphatic alcohols from their azeotropic aqueous mixtures is of particular interest to industrial process. The addition of the EPPS as an auxiliary agent breaks the (1-propanol + water) and (2-methyl-2-propanol + water) azeotropes. The possibility of using the new phase separation systems in the extraction process is demonstrated by using different dyestuffs.

Contribution of solution pH and buffer capacity to suppress intergranular stress corrosion cracking of sensitized type 304 stainless steel at 95 C

International Nuclear Information System (INIS)

Zhang, S.; Shibata, T.; Haruna, T.

1999-01-01

Controlling pH of high-temperature water to ∼pH 7 at 300 C by adding lithium hydroxide (LiOH) into the coolant system of a pressurized water reactor (PWR) successfully has been mitigating the corrosion of PWR component materials. The effects of solution pH and buffer capacity on intergranular stress corrosion cracking (IGSCC) of sensitized type 304 stainless steel ([SS] UNS S30400) was examined at 95 C by slow strain rate technique (SSRT) with an in-situ cracking observation system. It was found that an increase in solution pH or buffer capacity increased crack initiation time and decreased mean crack initiation frequency, but exerted almost no effect on crack propagation. This inhibition effect on IGSCC initiation was explained as resulting from a retarding effect of solution pH and buffer capacity on the decrease in pH at crack nuclei caused by the hydrolysis of metal ions dissolved when the passive film was ruptured by strain in SSRT

Liquid growth hormone: preservatives and buffers

DEFF Research Database (Denmark)

Kappelgaard, Anne-Marie; Anders, Bojesen; Skydsgaard, Karen

2004-01-01

injection are dependent on the preservative used in the formulation and the concentration of GH. Injection pain may also be related to the buffer substance and injection volume. A liquid formulation of GH, Norditropi SimpleXx, has been developed that dispenses with the need for reconstitution before...... solution. More pain was also reported following large volume injections and following injections with solutions containing high protein concentrations. In summary, optimization of the preservative and buffer content of a liquid GH formulation may reduce injection pain and lead to improved patient...... administration. The formulation uses phenol (3 mg/ml) as a preservative (to protect product from microbial degradation or contamination) and histidine as a buffer. Alternative preservatives used in other GH formulations include m-cresol (9 mg/ml) and benzyl alcohol (3-9 mg/ml). Buffering agents include citrate...

An improvement to the ligand optimisation method (LOM) for measuring the apparent dissociation constant and ligand purity in Ca2+ and Mg2+ buffer solutions.

Science.gov (United States)

McGuigan, John A S; Kay, James W; Elder, Hugh Y

2014-01-01

In Ca(2+)/Mg(2+) buffers the calculated ionised concentrations ([X(2+)]) can vary by up to a factor of seven. Since there are no defined standards it is impossible to check calculated [X(2+)], making measurement essential. The ligand optimisation method (LOM) is an accurate method to measure [X(2+)] in Ca(2+)/Mg(2+) buffers; independent estimation of ligand purity extends the method to pK(/) buffers, to calculate electrode and buffer characteristics as a function of Σ. Ca(2+)-electrodes have a Σ buffers. These results demonstrated that it is pK(/) that is normally distributed. Until defined standards are available, [X(2+)] in Ca(2+)/Mg(2+) buffers have to be measured. The most appropriate method is to use Ca(2+)/Mg(2) electrodes combined with the Excel programs SALE or AEC. Copyright © 2014 Elsevier Ltd. All rights reserved.

Sm-doped CeO{sub 2} single buffer layer for YBCO coated conductors by polymer assisted chemical solution deposition (PACSD) method

Energy Technology Data Exchange (ETDEWEB)

Li, G.; Pu, M.H.; Sun, R.P.; Wang, W.T.; Wu, W.; Zhang, X.; Yang, Y. [Key Laboratory of Magnetic Levitation Technologies and Maglev Trains (Ministry of Education of China), Superconductivity R and D Center (SRDC), Mail Stop 165, Southwest Jiaotong University, Chengdu 610031 (China); Cheng, C.H. [Key Laboratory of Magnetic Levitation Technologies and Maglev Trains (Ministry of Education of China), Superconductivity R and D Center (SRDC), Mail Stop 165, Southwest Jiaotong University, Chengdu 610031 (China); School of Materials Science and Engineering, University of New South Wales, Sydney, 2052 NSW (Australia); Zhao, Y. [Key Laboratory of Magnetic Levitation Technologies and Maglev Trains (Ministry of Education of China), Superconductivity R and D Center (SRDC), Mail Stop 165, Southwest Jiaotong University, Chengdu 610031 (China); School of Materials Science and Engineering, University of New South Wales, Sydney, 2052 NSW (Australia)], E-mail: yzhao@home.swjtu.edu.cn

2008-10-20

An over 150 nm thick Sm{sub 0.2}Ce{sub 0.8}O{sub 1.9-x} (SCO) single buffer layer has been deposited on bi-axially textured NiW (2 0 0) alloy substrate. Highly in-plane and out-of-plane oriented, dense, smooth and crack free SCO single layer has been obtained via a polymer-assisted chemical solution deposition (PACSD) approach. YBCO thin film has been deposited equally via a PACSD route on the SCO-buffered NiW, the as grown YBCO yielding a sharp transition at T{sub c0} = 87 K as well as J{sub c}(0 T, 77 K) {approx} 1 MA/cm{sup 2}. These results indicates that RE (lanthanides other than Ce) doping may be an effective approach to improve the critical thickness of solution derived CeO{sub 2} film, which renders it a promising candidate as single buffer layer for YBCO coated conductors.

Acid-base profile and predictors of metabolic acidosis in patients undergoing peritoneal dialysis with lactate- and bicarbonate-buffered peritoneal dialysis solutions.

Science.gov (United States)

Fourtounas, Costas; Savidaki, Eirini; Roumelioti, Marilena; Dousdampanis, Periklis; Hardalias, Andreas; Kalliakmani, Pantelitsa; Papachristou, Evangelos; Drakopoulos, Anastasios; Goumenos, Dimitrios S; Vlachojannis, Jannis G

2006-01-01

Metabolic acidosis correction is one of the goals of renal replacement therapy. Correction of acidosis in peritoneal dialysis (PD) may be affected by PD modalities such as automated PD (APD) or by new solutions containing a combination of bicarbonate and lactate as a buffer [bicarbonate continuous ambulatory PD (CAPD)]. The aim of the present study was to examine the acid-base status of our PD population and to compare the effects of APD, lactate CAPD, and bicarbonate CAPD on serum bicarbonate levels. We studied 35 stable patients undergoing APD (n = 15), lactate-buffered (35 mEq/L) CAPD (n = 14), and bicarbonate/lactate-buffered CAPD (n = 6) for 48.5 +/- 38.1 months. Most of our patients had serum bicarbonate levels in the normal range. In 3 patients (8%), HCO3 was below 22 mEq/L, and in 8 patients (22%; APD = 2, lactate CAPD = 2, bicarbonate CAPD = 4), HCO3 was above 28 mEq/L. We found no statistically significant correlations between HCO3 serum levels and PD prescription, peritoneal membrane characteristics, or intake of calcium carbonate and sevelamer hydrochloride. Patients on bicarbonate CAPD had higher HCO3 serum levels, but this difference disappeared when corrections for duration of dialysis, residual urine volume, and PD adequacy indices were applied. In the studied PD population, adequate correction of metabolic acidosis was achieved, as reflected in serum bicarbonate levels. We observed no difference in serum bicarbonate levels between APD and lactate CAPD patients. The new bicarbonate-buffered PD solutions are more biocompatible and can result in higher serum bicarbonate levels. However, a significant number of PD patients on bicarbonate-buffered solutions may become alkalotic. The clinical significance of these results needs further examination in prospective studies.

Buffer fluid

Energy Technology Data Exchange (ETDEWEB)

Mirzadzhanzade, A Kh; Dedusanko, G Ya; Dinaburg, L S; Markov, Yu M; Rasizade, Ya N; Rozov, V N; Sherstnev, N M

1979-08-30

A drilling fluid is suggested for separating the drilling and plugging fluids which contains as the base increased solution of polyacrylamide and additive. In order to increase the viscoelastic properties of the liquid with simultaneous decrease in the periods of its fabrication, the solution contains as an additive dry bentonite clay. In cases of the use of a buffer fluid under conditions of negative temperatures, it is necessary to add to it table salt or ethylene glycol.

Solution thermodynamics of pyrazinamide, isoniazid, and p-aminobenzoic acid in buffers and octanol

International Nuclear Information System (INIS)

Blokhina, Svetlana V.; Ol’khovich, Marina V.; Sharapova, Angelica V.; Volkova, Tatyana V.; Perlovich, German L.

2015-01-01

Highlights: • Solubility of pyrazinamide, isoniazid, p-aminobenzoic acid were measured. • The activity coefficients of the compounds at infinite dilution were determined. • Thermodynamic functions of dissolution and solvation were calculated. - Abstract: The solubility values of pyrazinamide, isoniazid, and p-aminobenzoic acid in buffers (pH 2.0 and 7.4) and octanol were measured in the temperature range of 293.15 to 313.15 K. The dissolution Gibbs energy, enthalpy, and entropy were calculated. The dissolving process was endothermic and enthalpy-determined. The activity coefficients of the compounds at infinite dilution were determined based on the solubility data and thermophysical parameters. A positive deviation from the ideality was observed in all the solutions. A common tendency of the solubility increase with a decrease in the activity coefficients at T = 298.15 K was revealed for the investigated solute-solvent systems. The excess thermodynamic solubility functions were calculated from the temperature dependences of the activity coefficients. The solvation processes were found to have a considerable influence on the solubility of the substances in solutions studied.

Study on CexLa1-xO2 Buffer Layer used in Coated Conductors by Chemical Solution Method

DEFF Research Database (Denmark)

Zhao, Yue; Suo, Hongli; Grivel, Jean-Claude

2009-01-01

Developing multi-functional single buffer layer is one of the most important challenges for simplification of coated conductors configuration. Ladoped CeO2 films were prepared by chemical solution method. And surface morphology and texture quality of the La-doped CeO2 films were investigated...... method. It suggects that Ce0.9La0.1O2 film prepared by chemical solution route have a promising prospect for the simplification of coated conductors configuration....

Programmable pH buffers

Science.gov (United States)

Gough, Dara Van; Huber, Dale L.; Bunker, Bruce C.; Roberts, Mark E.

2017-01-24

A programmable pH buffer comprises a copolymer that changes pK.sub.a at a lower critical solution temperature (LCST) in water. The copolymer comprises a thermally programmable polymer that undergoes a hydrophobic-to-hydrophilic phase change at the LCST and an electrolytic polymer that exhibits acid-base properties that are responsive to the phase change. The programmable pH buffer can be used to sequester CO.sub.2 into water.

Experimental acidification of two biogeochemically-distinct neotropical streams: Buffering mechanisms and macroinvertebrate drift

International Nuclear Information System (INIS)

Ardón, Marcelo; Duff, John H.; Ramírez, Alonso; Small, Gaston E.; Jackman, Alan P.; Triska, Frank J.; Pringle, Catherine M.

2013-01-01

Research into the buffering mechanisms and ecological consequences of acidification in tropical streams is lacking. We have documented seasonal and episodic acidification events in streams draining La Selva Biological Station, Costa Rica. Across this forested landscape, the severity in seasonal and episodic acidification events varies due to interbasin groundwater flow (IGF). Streams that receive IGF have higher concentrations of solutes and more stable pH (∼ 6) than streams that do not receive IGF (pH ∼ 5). To examine the buffering capacity and vulnerability of macroinvertebrates to short-term acidification events, we added hydrochloric acid to acidify a low-solute, poorly buffered (without IGF) and a high-solute, well buffered stream (with IGF). We hypothesized that: 1) protonation of bicarbonate (HCO 3 − ) would neutralize most of the acid added in the high-solute stream, while base cation release from the sediments would be the most important buffering mechanism in the low-solute stream; 2) pH declines would mobilize inorganic aluminum (Ali) from sediments in both streams; and 3) pH declines would increase macroinvertebrate drift in both streams. We found that the high-solute stream neutralized 745 μeq/L (96% of the acid added), while the solute poor stream only neutralized 27.4 μeq/L (40%). Protonation of HCO 3 − was an important buffering mechanism in both streams. Base cation, Fe 2+ , and Ali release from sediments and protonation of organic acids also provided buffering in the low-solute stream. We measured low concentrations of Ali release in both streams (2-9 μeq/L) in response to acidification, but the low-solute stream released double the amount Ali per 100 μeq of acid added than the high solute stream. Macroinvertebrate drift increased in both streams in response to acidification and was dominated by Ephemeroptera and Chironomidae. Our results elucidate the different buffering mechanisms in tropical streams and suggest that low-solute

The corrosion behaviour of rare-earth containing magnesium alloys in borate buffer solution

Energy Technology Data Exchange (ETDEWEB)

Pinto, R. [ICEMS, Instituto Superior Tecnico, Technical University of Lisbon (Portugal); Ferreira, M.G.S. [ICEMS, Instituto Superior Tecnico, Technical University of Lisbon (Portugal); CICECO, Universidade de Aveiro (Portugal); Carmezim, M.J. [ICEMS, Instituto Superior Tecnico, Technical University of Lisbon (Portugal); Instituto Politecnico de Setubal, ESTSetubal, DEM (Portugal); Montemor, M.F., E-mail: mfmontemor@ist.utl.p [ICEMS, Instituto Superior Tecnico, Technical University of Lisbon (Portugal)

2011-01-01

In this work, the corrosion behaviour of magnesium alloys ZK31, EZ33 and WE54 was studied in sodium borate buffer solution at pH 9.2. The electrochemical processes were studied by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS). The composition and morphology of the alloys and corrosion products formed were studied by scanning electron microscopy (SEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The experimental findings highlighted the differences in the corrosion mechanisms of the different alloys tested. The results showed that the presence of rare-earth elements (RE) only increases the corrosion resistance when present in solid solution, as is the case of the WE54 alloy. At pH 9.2, an amorphous yttrium oxide/hydroxide thick film was formed, which possesses greater stability when compared to magnesium oxide/hydroxide. The role of RE in the corrosion mechanism was discussed.

Flow and transport through a damaged buffer - exploration of the impact of a cemented and an eroded buffer

Energy Technology Data Exchange (ETDEWEB)

Neretnieks, Ivars [Dept. of Chemical Engineering and Technology, Royal Institute of Technology, Stockholm (Sweden)

2006-12-15

The compacted bentonite buffer that surrounds the canister with spent fuel is designed not to allow water to flow through it in any appreciable quantities. Should the buffer be severely damaged water could flow to the canister and bring with it corrosive agent such as sulphide. This could speed up the rate of copper corrosion. Should the canister have a damage or be corroded so that the spent fuel inside the canister comes in contact with the water radionuclides could dissolve in the water and be carried away. Two modes of canister damage and their consequences for solute transport are explored in this report. In one case the buffer can potentially be eroded by the water seeping in the fractures in the surrounding rock and attain a high hydraulic conductivity allowing water to flow through it, at least locally. In another case it is conjectured that the buffer is cemented and becomes brittle. Then a crack could conceivably form in the cemented buffer allowing water to flow through it directly to the canister surface. Both cases are hypothetical although in the erosion case the erosion rate could possibly be quantified. The cases studied are to be seen as exploratory calculations for 'what if' cases. Some worst case assumptions have been used to explore bounding scenarios. Thus for the erosion case it is assumed that the hydraulic conductivity is so high that the buffer exerts negligible resistance to water flow. This implies that all the water that can flow through the fractures intersecting the deposition hole can reach the canister. Similarly for the cemented buffer case it is assumed that the crack in the buffer directly connects the rock fracture to the canister surface. For these circumstances it is found that the flowrate that can enter the deposition hole will be approximately two times as large as the water flow that would pass a projected area equal to that of the deposition hole. Thus if the flux in the rock some distance from the deposition

Flow and transport through a damaged buffer - exploration of the impact of a cemented and an eroded buffer

International Nuclear Information System (INIS)

Neretnieks, Ivars

2006-12-01

The compacted bentonite buffer that surrounds the canister with spent fuel is designed not to allow water to flow through it in any appreciable quantities. Should the buffer be severely damaged water could flow to the canister and bring with it corrosive agent such as sulphide. This could speed up the rate of copper corrosion. Should the canister have a damage or be corroded so that the spent fuel inside the canister comes in contact with the water radionuclides could dissolve in the water and be carried away. Two modes of canister damage and their consequences for solute transport are explored in this report. In one case the buffer can potentially be eroded by the water seeping in the fractures in the surrounding rock and attain a high hydraulic conductivity allowing water to flow through it, at least locally. In another case it is conjectured that the buffer is cemented and becomes brittle. Then a crack could conceivably form in the cemented buffer allowing water to flow through it directly to the canister surface. Both cases are hypothetical although in the erosion case the erosion rate could possibly be quantified. The cases studied are to be seen as exploratory calculations for 'what if' cases. Some worst case assumptions have been used to explore bounding scenarios. Thus for the erosion case it is assumed that the hydraulic conductivity is so high that the buffer exerts negligible resistance to water flow. This implies that all the water that can flow through the fractures intersecting the deposition hole can reach the canister. Similarly for the cemented buffer case it is assumed that the crack in the buffer directly connects the rock fracture to the canister surface. For these circumstances it is found that the flowrate that can enter the deposition hole will be approximately two times as large as the water flow that would pass a projected area equal to that of the deposition hole. Thus if the flux in the rock some distance from the deposition hole is 1

Aluminum elution and precipitation in glass vials: effect of pH and buffer species.

Science.gov (United States)

Ogawa, Toru; Miyajima, Makoto; Wakiyama, Naoki; Terada, Katsuhide

2015-02-01

Inorganic extractables from glass vials may cause particle formation in the drug solution. In this study, the ability of eluting Al ion from borosilicate glass vials, and tendencies of precipitation containing Al were investigated using various pHs of phosphate, citrate, acetate and histidine buffer. Through heating, all of the buffers showed that Si and Al were eluted from glass vials in ratios almost the same as the composition of borosilicate glass, and the amounts of Al and Si from various buffer solutions at pH 7 were in the following order: citrate > phosphate > acetate > histidine. In addition, during storage after heating, the Al concentration at certain pHs of phosphate and acetate buffer solution decreased, suggesting the formation of particles containing Al. In citrate buffer, Al did not decrease in spite of the high elution amount. Considering that the solubility profile of aluminum oxide and the Al eluting profile of borosilicate glass were different, it is speculated that Al ion may be forced to leach into the buffer solution according to Si elution on the surface of glass vials. When Al ions were added to the buffer solutions, phosphate, acetate and histidine buffer showed a decrease of Al concentration during storage at a neutral range of pHs, indicating the formation of particles containing Al. In conclusion, it is suggested that phosphate buffer solution has higher possibility of forming particles containing Al than other buffer solutions.

Experimental acidification of two biogeochemically-distinct neotropical streams: Buffering mechanisms and macroinvertebrate drift

Energy Technology Data Exchange (ETDEWEB)

Ardón, Marcelo, E-mail: ardonsayaom@ecu.edu [Department of Biology and North Carolina Center for Biodiversity, East Carolina University, Greenville, NC 27858 (United States); Duff, John H. [U.S. Geological Survey, Menlo Park, CA 94025 (United States); Ramírez, Alonso [Department of Environmental Sciences, University of Puerto Rico, San Juan, PR 00931 (Puerto Rico); Small, Gaston E. [Department of Ecology, Evolution, and Behavior, University of Minnesota, St. Paul, MN 55108 (United States); Jackman, Alan P. [University of California, Davis, CA 95616 (United States); Triska, Frank J. [U.S. Geological Survey, Menlo Park, CA 94025 (United States); Pringle, Catherine M. [Odum School of Ecology, University of Georgia, Athens, GA 30602 (United States)

2013-01-15

Research into the buffering mechanisms and ecological consequences of acidification in tropical streams is lacking. We have documented seasonal and episodic acidification events in streams draining La Selva Biological Station, Costa Rica. Across this forested landscape, the severity in seasonal and episodic acidification events varies due to interbasin groundwater flow (IGF). Streams that receive IGF have higher concentrations of solutes and more stable pH (∼ 6) than streams that do not receive IGF (pH ∼ 5). To examine the buffering capacity and vulnerability of macroinvertebrates to short-term acidification events, we added hydrochloric acid to acidify a low-solute, poorly buffered (without IGF) and a high-solute, well buffered stream (with IGF). We hypothesized that: 1) protonation of bicarbonate (HCO{sub 3}{sup −}) would neutralize most of the acid added in the high-solute stream, while base cation release from the sediments would be the most important buffering mechanism in the low-solute stream; 2) pH declines would mobilize inorganic aluminum (Ali) from sediments in both streams; and 3) pH declines would increase macroinvertebrate drift in both streams. We found that the high-solute stream neutralized 745 μeq/L (96% of the acid added), while the solute poor stream only neutralized 27.4 μeq/L (40%). Protonation of HCO{sub 3}{sup −} was an important buffering mechanism in both streams. Base cation, Fe{sup 2+}, and Ali release from sediments and protonation of organic acids also provided buffering in the low-solute stream. We measured low concentrations of Ali release in both streams (2-9 μeq/L) in response to acidification, but the low-solute stream released double the amount Ali per 100 μeq of acid added than the high solute stream. Macroinvertebrate drift increased in both streams in response to acidification and was dominated by Ephemeroptera and Chironomidae. Our results elucidate the different buffering mechanisms in tropical streams and

Corrosion and Passivation of Nickel Rotating Disk Electrode in Borate Buffer Solution

Energy Technology Data Exchange (ETDEWEB)

Kim, Younkyoo [Hankuk Univ. of Foreign Studies, Yongin (Korea, Republic of)

2013-10-15

The electrochemical corrosion and passivation of Ni rotating disk electrod in borate buffer solution was studied with potentiodynamic and electrochemical impedance spectroscopy. The mechanisms of both the active dissolution and passivation of nickel and the hydrogen evolution in reduction reaction were hypothetically established while utilizing the Tafel slope, impedance data, the rotation speed of Ni-RDE and the pH dependence of corrosion potential and current. Based on the EIS data, an equivalent circuit was suggested. In addition, carefully measured were the electrochemical parameters for specific anodic dissolution regions. It can be concluded from the data collected that the Ni(OH){sub 2} oxide film, which is primarily formed by passivation, is converted to NiO by dehydration under the influence of an electrical field.

Thermochemical parameters of minerals from oxygen-buffered hydrothermal equilibrium data: Method, application to annite and almandine

Science.gov (United States)

Zen, E.-A.

1973-01-01

Reversed univariant hydrothermal phase-equilibrium reactions, in which a redox reaction occurs and is controlled by oxygen buffers, can be used to extract thermochemical data on minerals. The dominant gaseous species present, even for relatively oxidizing buffers such as the QFM buffer, are H2O and H2; the main problem is to calculate the chemical potentials of these components in a binary mixture. The mixing of these two species in the gas phase was assumed by Eugster and Wones (1962) to be ideal; this assumption allows calculation of the chemical potentials of the two components in a binary gas mixture, using data in the literature. A simple-mixture model of nonideal mixing, such as that proposed by Shaw (1967), can also be combined with the equations of state for oxygen buffers to permit derivation of the chemical potentials of the two components. The two mixing models yield closely comparable results for the more oxidizing buffers such as the QFM buffer. For reducing buffers such as IQF, the nonideal-mixing correction can be significant and the Shaw model is better. The procedure of calculation of mineralogical thermochemical data, in reactions where hydrogen and H2O simultaneously appear, is applied to the experimental data on annite, given by Wones et al. (1971), and on almandine, given by Hsu (1968). For annite the results are: Standard entropy of formation from the elements, Sf0 (298, 1)=-283.35??2.2 gb/gf, S0 (298, 1) =+92.5 gb/gf. Gf0 (298, 1)=-1148.2??6 kcal, and Hf0 (298, 1)=-1232.7??7 kcal. For almandine, the calculation takes into account the mutual solution of FeAl2O4 (Hc) in magnetite and of Fe3O4 (Mt) in hercynite and the temperature dependence of this solid solution, as given by Turnock and Eugster (1962); the calculations assume a regular-solution model for this binary spinel system. The standard entropy of formation of almandine, Sf,A0 (298, 1) is -272.33??3 gb/gf. The third law entropy, S0 (298, 1) is +68.3??3 gb/gf, a value much less than the

The Influence of Phosphate Buffer on the Formation of N-Nitrosodimethylamine from Dimethylamine Nitrosation

Directory of Open Access Journals (Sweden)

Long Xu

2013-01-01

Full Text Available Buffer solutions were widely used for almost all the investigations concerning N-nitrosodimethylamine (NDMA, a member of powerful mutagenic and carcinogenic compounds which are ubiquitous in the environment. However, whether or how the buffer matrixes influence NDMA formation is still unknown. The effect of buffer solutions on NDMA formation from the nitrosation of dimethylamine (DMA by nitrite (NaNO2 was investigated at pH 6.4 in four kinds of buffer solutions, that is, Na2HPO4/C6H8O7, Na3(C6H5O7/C6H8O7, NaH2PO4/NaOH, and NaH2PO4/Na2HPO4. Our observations demonstrate an unexpected inhibitory effect of the buffer solutions on NDMA formation and the phosphate buffer plays a more significant role in inhibiting NDMA formation compared to the citrate buffer. Moreover, the amount of the phosphate in the buffer was also found to greatly impact the formation of NDMA. A further investigation indicates that it is the interaction between NaH2PO4 and reactant NaNO2 rather than DMA that leads to the inhibitory effect of phosphate buffer during the DMA nitrosation reaction. This study expands the understanding of the influence of buffer solution on nitrosamines formation through the nitrosation pathway and further gives a hint for water plants to reduce the formation of nitrosamines.

Buffer erosion in dilute groundwater

International Nuclear Information System (INIS)

Schatz, T.; Kanerva, N.; Martikainen, J.; Sane, P.; Olin, M.; Seppaelae, A.; Koskinen, K.

2013-08-01

One scenario of interest for repository safety assessment involves the loss of bentonite buffer material in contact with dilute groundwater flowing through a transmissive fracture interface. In order to examine the extrusion/erosion behavior of bentonite buffer material under such circumstances, a series of experiments were performed in a flow-through, 1 mm aperture, artificial fracture system. These experiments covered a range of solution chemistry (salt concentration and composition), material composition (sodium montmorillonite and admixtures with calcium montmorillonite), and flow velocity conditions. No erosion was observed for sodium montmorillonite against solution compositions from 0.5 g/L to 10 g/L NaCl. No erosion was observed for 50/50 calcium/sodium montmorillonite against 0.5 g/L NaCl. Erosion was observed for both sodium montmorillonite and 50/50 calcium/sodium montmorillonite against solution compositions ≤ 0.25 g/L NaCl. The calculated erosion rates for the tests with the highest levels of measured erosion, i.e., the tests run under the most dilute conditions (ionic strength (IS) < ∼1 mM), were well-correlated to flow velocity, whereas the calculated erosion rates for the tests with lower levels of measured erosion, i.e., the tests run under somewhat less dilute conditions (∼1 mM < IS < ∼4 mM), were not similarly correlated indicating that material and solution composition can significantly affect erosion rates. In every experiment, both erosive and non-erosive, emplaced buffer material extruded into the fracture and was observed to be impermeable to water flowing in the fracture effectively forming an extended diffusive barrier around the intersecting fracture/buffer interface. Additionally, a model which was developed previously to predict the rate of erosion of bentonite buffer material in low ionic strength water in rock fracture environments was applied to three different cases: sodium montmorillonite expansion in a vertical tube, a

Avaliação da capacidade tamponante - um experimento participativo Buffer capacity evaluating - a collaborative experiment

Directory of Open Access Journals (Sweden)

César Ricardo Silva

2000-06-01

Full Text Available The aim of this work is to show an experiment from which students can learn some of the main characteristics of buffer solutions. A mixture of some acid-base indicators, named as Yamada's indicator, can be used to estimate pH values in an acid-base titration of a buffer, with good approximation. In the experiment it is also possible to verify the relationship between the buffer capacity and the concentrations and the molar ratio of the components of a NH3 / NH4+ buffer solution. The shortage of experiments associated with the relative small importance given to many aspects of buffer solutions, is now explored with simplicity. In the proposed experiments, students prepare buffer solutions by themselves, calculate the pH, understand how acid-base indicators act and learn how buffer solutions work through graph constructed by sharing experimental data.

Effects of EDTA on the electronic properties of passive film formed on Fe-20Cr in pH 8.5 buffer solution

International Nuclear Information System (INIS)

Cho, Eun Ae; Kwon, Hyuk Sang; Beranrd, Frederic

2003-01-01

The electronic properties of the passive film formed on Fe-20Cr ferritic stainless steel in pH 8.5 buffer solution containing 0.05 M EDTA (ethylene diammine tetraacetic acid) were examined by the photocurrent measurements and Mott-Schottky analysis for the film. XPS depth profile for the film demonstrated that Cr content in the outermost layer of the passive film was higher in the solution with EDTA than that in the solution without EDTA, due to selective dissolution of Fe by EDTA. In the solution with EDTA, the passive film showed characteristics of an amorphous or highly disordered n-type semiconductor. The band gap energies of the passive film are estimated to be ∼ 3.0 eV, irrespective of film formation potential from 0 to 700 mV SCE and of presence of EDTA. However, the donor density of the passive film formed in the solution with EDTA is much higher than that formed in the solution without EDTA, due to an increase in oxygen vacancy resulted from the dissolution of Fe-oxide in the outermost layer of the passive film. These results support the proposed model that the passive film formed on Fe-20Cr in pH 8.5 buffer solution mainly consists of Cr-substituted γ-Fe 2 O 3

Photo-electrochemical analysis of passive film formed on X80 pipeline steel in bicarbonate/carbonate buffer solution

Energy Technology Data Exchange (ETDEWEB)

Li, D.G. [School of Materials Science and Engineering, Xi' an Jiaotong University, Xi' an 710049 (China); Tubular Goods Research Center of CNPC, Xi' an 710065 (China)], E-mail: dangguoli78@yahoo.com.cn; Feng, Y.R.; Bai, Z.Q. [Tubular Goods Research Center of CNPC, Xi' an 710065 (China); Zhu, J.W.; Zheng, M.S. [School of Materials Science and Engineering, Xi' an Jiaotong University, Xi' an 710049 (China)

2008-02-28

Photo-electrochemical measurement was used to explore the formation potential, formation time, chloride ions concentration, applied potential and pH value of the solution on the electronic property of passive film formed on X80 pipeline steel in 1 M NaHCO{sub 3}/0.5 M Na{sub 2}CO{sub 3} buffer solution. The results showed that the photocurrent is positive, indicating an n-type semiconductor character of the passive film, the photocurrent increased with increasing the formation potential, prolonging the formation time, decreasing chloride ions concentration, rising applied potential and decreasing the pH value of the solution. Capacitance measurement exhibited a positive slope of Mott-Schottky plot, and the slopes of Mott-Schottky plots increased with the increasing formation potential, showing a decrement of the donor density of the passive film.

Throughput maximization for buffer-aided hybrid half-/full-duplex relaying with self-interference

KAUST Repository

Khafagy, Mohammad Galal

2015-06-01

In this work, we consider a two-hop cooperative setting where a source communicates with a destination through an intermediate relay node with a buffer. Unlike the existing body of work on buffer-aided half-duplex relaying, we consider a hybrid half-/full-duplex relaying scenario with loopback interference in the full-duplex mode. Depending on the channel outage and buffer states that are assumed available at the transmitters, the source and relay may either transmit simultaneously or revert to orthogonal transmission. Specifically, a joint source/relay scheduling and relaying mode selection mechanism is proposed to maximize the end-to-end throughput. The throughput maximization problem is converted to a linear program where the exact global optimal solution is efficiently obtained via standard convex/linear numerical optimization tools. Finally, the theoretical findings are corroborated with event-based simulations to provide the necessary performance validation.

Use of 8.4% Sodium Bicarbonate in Buffering Commonly Administered Vancomycin Hydrochloride Solutions for Use with Midline or Peripheral Line Catheters.

Science.gov (United States)

Puertos, Enrique; Spencer, Melissa

2015-01-01

The primary objective of this study was to evaluate the use of 8.4% sodium bicarbonate in the buffering of commonly administered vancomycin hydrochloride solutions for use with midline or peripheral line catheters. Nine admixtures of vancomycin hydrochloride were aseptically prepared for this study. Vancomycin hydrochloride solutions were prepared in triplicates in the following strengths, 1 gram, 2 grams, and 3 grams, which were added to 250-mL bags of sodium chloride 0.9% injection (with overfill). To each prepared solution of vancomycin hydrochloride, 0.5 mL of 8.4% sodium bicarbonate was added. The pH was measured to obtain a baseline level. At day 9, the pH of each sample was measured and compared to those at baseline. The osmolality of each sample was also measured. There was no statistical difference in the pH at baseline and at day 9 (α = 0.05, P = 0.347). A solution of vancomycin hydrochloride that is compounded in 250 mL of sodium chloride 0.9% injection (including overfill) and buffered with 0.5 mL of 8.4% sodium bicarbonate maintained a pH in the range of 5 to 9 and an osmolality in the range of 150 mOsm/kg to 500 mOsm/kg.

Influence of pH and oxygen content of buffer solutions on the corrosion behaviour of metallic materials

International Nuclear Information System (INIS)

Wiedemann, K.H.

1977-05-01

The application of solutions to the decontamination of materials in nuclear installations is based on the condition that their corrosion behaviour is clearly understood. Since electrochemical corrosion is due to cathodic and anodic partial reactions which are influenced in different ways by the pH of the solution and the oxygen content it is suggested that the results of electrochemical experiments with buffer solutions be used as a model for predicting the corrosion behaviour of materials in other solutions. In the tests described here potentio-kinetic current-potential-curves have been traced and galvanic corrosion tests have been made. The results obtained in ascorbic acid, potassium hydrogen phthalate, ammonium citrate and acetate, sodium and potassium tartrate, ammonium hydrogen phosphate, sodium carbonate, hexamethylene tetramin, ethylene diamine enable - on the basis of summarized current-potential-curves - the metals studied to be classified in four groups characterized by clear differences concerning the influence of pH on the corrosion behaviour. (Auth.)

Enhanced magnetic properties of chemical solution deposited BiFeO3 thin film with ZnO buffer layer

International Nuclear Information System (INIS)

Rajalakshmi, R.; Kambhala, Nagaiah; Angappane, S.

2012-01-01

Highlights: ► Enhanced magnetization of BiFeO 3 is important for strong magnetoelectric coupling. ► BiFeO 3 film with ZnO buffer layer was successfully synthesized by chemical method. ► Magnetization of BiFeO 3 has increased by more than 10 times with ZnO buffer layer. ► A mechanism for enhancement in ferromagnetism of BiFeO 3 film is proposed. - Abstract: Magnetic properties of BiFeO 3 films deposited on Si substrates with and without ZnO buffer layer have been studied in this work. We adopted the chemical solution deposition method for the deposition of BiFeO 3 as well as ZnO films. The x-ray diffraction measurements on the deposited films confirm the formation of crystalline phase of BiFeO 3 and ZnO films, while our electron microscopy measurements help to understand the morphology of few micrometers thick films. It is found that the deposited ZnO film exhibit a hexagonal particulate surface morphology, whereas BiFeO 3 film fully covers the ZnO surface. Our magnetic measurements reveal that the magnetization of BiFeO 3 has increased by more than ten times in BiFeO 3 /ZnO/Si film compared to BiFeO 3 /Si film, indicating the major role played by ZnO buffer layer in enhancing the magnetic properties of BiFeO 3 , a technologically important multiferroic material.

Variation of power generation at different buffer types and conductivities in single chamber microbial fuel cells

KAUST Repository

Nam, Joo-Youn

2010-01-15

Microbial fuel cells (MFCs) are operated with solutions containing various chemical species required for the growth of electrochemically active microorganisms including nutrients and vitamins, substrates, and chemical buffers. Many different buffers are used in laboratory media, but the effects of these buffers and their inherent electrolyte conductivities have not been examined relative to current generation in MFCs. We investigated the effect of several common buffers (phosphate, MES, HEPES, and PIPES) on power production in single chambered MFCs compared to a non-buffered control. At the same concentrations the buffers produced different solution conductivities which resulted in different ohmic resistances and power densities. Increasing the solution conductivities to the same values using NaCl produced comparable power densities for all buffers. Very large increases in conductivity resulted in a rapid voltage drop at high current densities. Our results suggest that solution conductivity at a specific pH for each buffer is more important in MFC studies than the buffer itself given relatively constant pH conditions. Based on our analysis of internal resistance and a set neutral pH, phosphate and PIPES are the most useful buffers of those examined here because pH was maintained close to the pKa of the buffer, maximizing the ability of the buffer to contribute to increase current generation at high power densities. © 2009 Elsevier B.V. All rights reserved.

Variation of power generation at different buffer types and conductivities in single chamber microbial fuel cells.

Science.gov (United States)

Nam, Joo-Youn; Kim, Hyun-Woo; Lim, Kyeong-Ho; Shin, Hang-Sik; Logan, Bruce E

2010-01-15

Microbial fuel cells (MFCs) are operated with solutions containing various chemical species required for the growth of electrochemically active microorganisms including nutrients and vitamins, substrates, and chemical buffers. Many different buffers are used in laboratory media, but the effects of these buffers and their inherent electrolyte conductivities have not been examined relative to current generation in MFCs. We investigated the effect of several common buffers (phosphate, MES, HEPES, and PIPES) on power production in single chambered MFCs compared to a non-buffered control. At the same concentrations the buffers produced different solution conductivities which resulted in different ohmic resistances and power densities. Increasing the solution conductivities to the same values using NaCl produced comparable power densities for all buffers. Very large increases in conductivity resulted in a rapid voltage drop at high current densities. Our results suggest that solution conductivity at a specific pH for each buffer is more important in MFC studies than the buffer itself given relatively constant pH conditions. Based on our analysis of internal resistance and a set neutral pH, phosphate and PIPES are the most useful buffers of those examined here because pH was maintained close to the pK(a) of the buffer, maximizing the ability of the buffer to contribute to increase current generation at high power densities. Copyright 2009 Elsevier B.V. All rights reserved.

Effects of air polishing and an amino acid buffered hypochlorite solution to dentin surfaces and periodontal ligament cell survival, attachment, and spreading.

Science.gov (United States)

Schmidlin, Patrick R; Fujioka-Kobayashi, Masako; Mueller, Heinz-Dieter; Sculean, Anton; Lussi, Adrian; Miron, Richard J

2017-06-01

The aim of this study is to examine morphological changes of dentin surfaces following air polishing or amino acid buffered hypochlorite solution application and to assess their influence on periodontal ligament (PDL) cell survival, attachment, and spreading to dentin discs in vitro. Bovine dentin discs were treated with either (i) Classic, (ii) Plus, or (iii) Perio powder (EMS). Furthermore, Perisolv® a hypochlorite solution buffered with various amino acids was investigated. Untreated dentin discs served as controls. Morphological changes to dentin discs were assessed using scanning electron microscopy (SEM). Human PDL cells were seeded onto the respectively treated discs, and samples were then investigated for PDL cell survival, attachment, and spreading using a live/dead assay, adhesion assay, and SEM imaging, respectively. Both control and Perisolv®-rinsed dentin discs demonstrated smooth surfaces at low and high magnifications. The Classic powders demonstrated the thickest coating followed by the Powder Plus. The Perio powder demonstrated marked alterations of dentin discs by revealing the potential to open dentinal tubules even before rinsing. Seeding of PDL cells demonstrated an almost 100 % survival rate on all samples demonstrating very high biocompatibility for all materials. Significantly higher PDL cell numbers were observed on samples treated with the Perio powder and the Perisolv® solution (approximately 40 % more cells; p air polishing or application with Perisolv®. Future in vitro and animal testing is necessary to further characterize the beneficial effects of either system in a clinical setting. The use of air polishing or application with Perisolv amino acid buffered hypochlorite solution was effective in treating root surfaces and allowed for near 100 % PDL cell survival, attachment, and spreading onto all root surfaces.

pH variations during diafiltration due to buffer nonidealities.

Science.gov (United States)

Baek, Youngbin; Yang, Deyu; Singh, Nripen; Arunkumar, Abhiram; Ghose, Sanchayita; Li, Zheng Jian; Zydney, Andrew L

2017-11-01

Diafiltration is used for final formulation of essentially all biotherapeutics. Several studies have demonstrated that buffer/excipient concentrations in the final diafiltered product can be different than that in the diafiltration buffer due to interactions between buffer species and the protein product. However, recent work in our lab has shown variations in solution pH that are largely independent of the protein concentration during the first few diavolumes. Our hypothesis is that these pH variations are due to nonidealities in the acid-base equilibrium coefficient. A model was developed for the diafiltration process accounting for the ionic strength dependence of the pK a . Experimental results obtained using phosphate and histidine buffers were in excellent agreement with model predictions. A decrease in ionic strength leads to an increase in the pK a for the phosphate buffer, causing a shift in the solution pH, even under conditions where the initial feed and the diafiltration buffer are at the same pH. This effect could be eliminated by matching the ionic strength of the feed and diafiltration buffer. The experimental data and model provide new insights into the factors controlling the pH profile during diafiltration processes. © 2017 American Institute of Chemical Engineers Biotechnol. Prog., 33:1555-1560, 2017. © 2017 American Institute of Chemical Engineers.

Thermophysical properties of carboxylic and amino acid buffers at subzero temperatures: relevance to frozen state stabilization.

Science.gov (United States)

Sundaramurthi, Prakash; Suryanarayanan, Raj

2011-06-02

Macromolecules and other thermolabile biologicals are often buffered and stored in frozen or dried (freeze-dried) state. Crystallization of buffer components in frozen aqueous solutions and the consequent pH shifts were studied in carboxylic (succinic, malic, citric, tartaric acid) and amino acid (glycine, histidine) buffers. Aqueous buffer solutions were cooled from room temperature (RT) to -25 °C and the pH of the solution was measured as a function of temperature. The thermal behavior of frozen solutions was investigated by differential scanning calorimetry (DSC), and the crystallized phases were identified by X-ray diffractometry (XRD). Based on the solubility of the neutral species of each buffer system over a range of temperatures, it was possible to estimate its degree of supersaturation at the subambient temperature of interest. This enabled us to predict its crystallization propensity in frozen systems. The experimental and the predicted rank orderings were in excellent agreement. The malate buffer system was robust with no evidence of buffer component crystallization and hence negligible pH shift. In the citrate and tartrate systems, at initial pH pI. In the histidine buffer system, depending on the initial pH, either histidine or histidine HCl crystallized.

Buffers and vegetative filter strips

Science.gov (United States)

Matthew J. Helmers; Thomas M. Isenhart; Michael G. Dosskey; Seth M. Dabney

2008-01-01

This chapter describes the use of buffers and vegetative filter strips relative to water quality. In particular, we primarily discuss the herbaceous components of the following NRCS Conservation Practice Standards.

Growth of thick La2Zr2O7 buffer layers for coated conductors by polymer-assisted chemical solution deposition

International Nuclear Information System (INIS)

Zhang, Xin; Zhao, Yong; Xia, Yudong; Guo, Chunsheng; Cheng, C.H.; Zhang, Yong; Zhang, Han

2015-01-01

Highlights: • We develops a low-cost and high-efficient technology of fabricating LZO buffer layers. • Sufficient thickness LZO buffer layers have been obtained on NiW (2 0 0) alloy substrate. • Highly biaxially textured YBCO thin film has been deposited on LZO/NiW. - Abstract: La 2 Zr 2 O 7 (LZO) epitaxial films have been deposited on LaAlO 3 (LAO) (1 0 0) single-crystal surface and bi-axially textured NiW (2 0 0) alloy substrate by polymer-assisted chemical solution deposition, and afterwards studied with XRD, SEM and AFM approaches. Highly in-plane and out-of-plane oriented, dense, smooth, crack free and with a sufficient thickness (>240 nm) LZO buffer layers have been obtained on LAO (1 0 0) single-crystal surface; The films deposited on NiW (2 0 0) alloy substrate are also found with high degree in-plane and out-of-plane texturing, good density with pin-hole-free, micro-crack-free nature and a thickness of 300 nm. Highly epitaxial 500 nm thick YBa 2 Cu 3 O 7−x (YBCO) thin film exhibits the self-field critical current density (Jc) reached 1.3 MA/cm 2 at 77 K .These results demonstrate the LZO epi-films obtained with current techniques have potential to be a buffer layer for REBCO coated conductors

Glucose buffer is suitable for blood group conversion with α-N acetylgalactosaminidase and α-galactosidase.

Science.gov (United States)

Gao, Hong-Wei; Li, Su-Bo; Bao, Guo-Qiang; Zhang, Xue; Li, Hui; Wang, Ying-Li; Tan, Ying-Xia; Ji, Shou-Ping; Gong, Feng

2014-01-01

It is well known that the buffer plays a key role in the enzymatic reaction involved in blood group conversion. In previous study, we showed that a glycine buffer is suitable for A to O or B to O blood group conversion. In this study, we investigated the use of 5% glucose and other buffers for A to O or B to O blood group conversion by α-N-acetylgalactosaminidase or α-galactosidase. We compared the binding ability of α-N-acetylgalactosaminidase/α-galactosidase with red blood cells (RBC) in different reaction buffers, such as normal saline, phosphate-buffered saline (PBS), a disodium hydrogen phosphate-based buffer (PCS), and 5% commercial glucose solution. The doses of enzymes necessary for the A/B to O conversion in different reaction buffers were determined and compared. The enzymes' ability to bind to RBC was evaluated by western blotting, and routine blood typing and fluorescence activated cell sorting was used to evaluate B/A to O conversion efficiency. The A to O conversion efficiency in glucose buffer was similar to that in glycine buffer with the same dose (>0.06 mg/mL pRBC). B to O conversion efficiency in glucose buffer was also similar to that in glycine buffer with the same dose (>0.005 mg/mL pRBC). Most enzymes could bind with RBC in glycine or glucose buffer, but few enzymes could bind with RBC in PBS, PCS, or normal saline. These results indicate that 5% glucose solution provides a suitable condition for enzymolysis, especially for enzymes combining with RBC. Meanwhile, the conversion efficiency of A/B to O was similar in glucose buffer and glycine buffer. Moreover, 5% glucose solution has been used for years in venous transfusion, it is safe for humans and its cost is lower. Our results do, therefore, suggest that 5% glucose solution could become a novel suitable buffer for A/B to O blood group conversion.

Heat conductivity of buffer materials

International Nuclear Information System (INIS)

Boergesson, L.; Fredrikson, Anders; Johannesson, L.E.

1994-11-01

The report deals with the thermal conductivity of bentonite based buffer materials. An improved technique for measuring the thermal conductivity of buffer materials is described. Measurements of FLAC calculations applying this technique have led to a proposal of how standardized tests should be conducted and evaluated. The thermal conductivity of bentonite with different void ratio and degree of water saturation has been determined in the following different ways: * Theoretically according to three different investigations by other researchers. * Laboratory measurements with the proposed method. * Results from back-calculated field tests. Comparison and evaluation showed that these results agreed very well, when the buffer material was almost water saturated. However, the influence of the degree of saturation was not very well predicted with the theoretical methods. Furthermore, the field tests showed that the average thermal conductivity in situ of buffer material (compacted to blocks) with low degree of water saturation was lower than expected from laboratory tests. 12 refs, 29 figs, 11 tabs

Establishment of carcinoembryonic antigen working standard for immunoassay

International Nuclear Information System (INIS)

Xu Ligen; Sun Youxiang; Jiao Yan

2001-01-01

The author is to prepare the working standard of carcinoembryonic antigen (CEA) for immunoassay and determine its potency. CEA solution of 320 μg/L was prepared from purified CEA solution of 4.6 mg/L and 1% human albumin solution buffered with 50 mmol/L sodium phosphate, pH7.4. This solution was distributed in an aliquot of 0.5 mL (160 ng per ampoule) and lyophilized. The potency of CEA working standard, in terms of present standard of CEA RIA and IRMA kits made by Chinese manufacturers and in terms of 1st IRP CEA HUMAN 73/601 supplied by WHO, has been determined. Mean immunological potency of the working standard is 163 ng per ampoule with confident limit of 159-168 ng per ampoule at 95% probability level. Test of parallelism of dose-response curve for the working standard to that for 1st IRP CEA HUMAN 73/601 has been passed. CEA working standard is suitable to the kits standard for CEA radioimmunoassay and immunoradiometric assay

Towards Optimal Buffer Size in Wi-Fi Networks

KAUST Repository

Showail, Ahmad J.

2016-01-19

Buffer sizing is an important network configuration parameter that impacts the quality of data traffic. Falling memory cost and the fallacy that ‘more is better’ lead to over provisioning network devices with large buffers. Over-buffering or the so called ‘bufferbloat’ phenomenon creates excessive end-to-end delay in today’s networks. On the other hand, under-buffering results in frequent packet loss and subsequent under-utilization of network resources. The buffer sizing problem has been studied extensively for wired networks. However, there is little work addressing the unique challenges of wireless environment. In this dissertation, we discuss buffer sizing challenges in wireless networks, classify the state-of-the-art solutions, and propose two novel buffer sizing schemes. The first scheme targets buffer sizing in wireless multi-hop networks where the radio spectral resource is shared among a set of con- tending nodes. Hence, it sizes the buffer collectively and distributes it over a set of interfering devices. The second buffer sizing scheme is designed to cope up with recent Wi-Fi enhancements. It adapts the buffer size based on measured link characteristics and network load. Also, it enforces limits on the buffer size to maximize frame aggregation benefits. Both mechanisms are evaluated using simulation as well as testbed implementation over half-duplex and full-duplex wireless networks. Experimental evaluation shows that our proposal reduces latency by an order of magnitude.

Development of standardized radioactive 46Sc solution

International Nuclear Information System (INIS)

Du Hongshan; Jia Zhang; Yu Yiguang; Sun Naiyao

1988-01-01

A method of preparation of standardized radioactive 46 Sc solution is developed. The separation of 46 Sc, the composition of 46 Sc solution and its stability, and radioactivity measurement of 46 Sc are systematically studied. The results obtained in the study and in the applications in many laboratories have shown that our method is effective and reliable

Effectiveness of the cross-compliance standard 5.2 'buffer strips' on protecting freshwater against diffuse nitrogen pollution

Directory of Open Access Journals (Sweden)

Bruna Gumiero

2016-02-01

Full Text Available Sette Fasce Tampone, realizzate secondo le indicazioni tecniche contenute nello standard di condizionalità 5.2, in diversi ambiti e contesti climatici, sono state monitorate per un periodo biennale, al fine di quantificare la loro efficienza nella rimozione di azoto inorganico disciolto. Tale azoto è costituito per lo più da molecole di azoto nitrico che vengono veicolate principalmente tramite deflussi sub-superficiali da zone soggette a diverse pratiche colturali verso i corpi idrici superficiali adiacenti. Ad eccezione di due casi: i siti di Lodi e Metaponto, in tutti i sistemi monitorati è stata confermata la presenza di deflussi trasversali ai sistemi tampone, permanenti o temporanei, in grado di veicolare inquinanti e con portate variabili fra 919 e 8.590 m3/anno per 100 m lineari di FT. Le differenze di portata sono imputabili principalmente alla diversa superficie dei bacini agricoli afferenti ai sistemi tampone, che nei casi analizzati occupano superfici variabili fra il 3,6 ed il 33,3% del bacino agricolo. Sulla base dei bilanci di massa è emerso che dai campi coltivati giungono ai sistemi tampone percentuali variabili fra l’1,6 ed il 29,4% dell’azoto inorganico applicato. Ad eccezione dei sistemi in cui i maggiori deflussi non hanno alcuna interazione con la rizosfera (deflussi profondi oppure non attraversano la Fascia Tampone, in tutti gli altri siti si registra un effetto di riduzione dell’azoto fra entrata ed uscita, con percentuali variabili fra il 33 ed il 62 %. Percentuali di abbattimento non elevate sono giustificate dallo scarso grado di maturazione dei siti monitorati, in molti casi recentemente convertiti a Fascia Tampone. Ancora una volta si conferma l’estrema eterogeneità delle risposte di questi sistemi ed il ruolo prioritario delle forzanti idrologiche nel determinarne l’efficacia.Seven buffer strips (BS adjacent to fresh water bodies, realized according to the technical data contained in the standard 5

Effectiveness of the cross-compliance Standard 5.2 'buffer strips' on protecting freshwater against diffuse nitrogen pollution

Directory of Open Access Journals (Sweden)

Bruna Gumiero

2016-02-01

Full Text Available Sette Fasce Tampone, realizzate secondo le indicazioni tecniche contenute nello Standard di condizionalità 5.2, in diversi ambiti e contesti climatici, sono state monitorate per un periodo biennale, al fine di quantificare la loro efficienza nella rimozione di azoto inorganico disciolto. Tale azoto è costituito per lo più da molecole di azoto nitrico che vengono veicolate principalmente tramite deflussi sub-superficiali da zone soggette a diverse pratiche colturali verso i corpi idrici superficiali adiacenti. Ad eccezione di due casi: i siti di Lodi e Metaponto, in tutti i sistemi monitorati è stata confermata la presenza di deflussi trasversali ai sistemi tampone, permanenti o temporanei, in grado di veicolare inquinanti e con portate variabili fra 919 e 8.590 m3/anno per 100 m lineari di FT. Le differenze di portata sono imputabili principalmente alla diversa superficie dei bacini agricoli afferenti ai sistemi tampone, che nei casi analizzati occupano superfici variabili fra il 3,6 ed il 33,3% del bacino agricolo. Sulla base dei bilanci di massa è emerso che dai campi coltivati giungono ai sistemi tampone percentuali variabili fra l’1,6 ed il 29,4% dell’azoto inorganico applicato. Ad eccezione dei sistemi in cui i maggiori deflussi non hanno alcuna interazione con la rizosfera (deflussi profondi oppure non attraversano la Fascia Tampone, in tutti gli altri siti si registra un effetto di riduzione dell’azoto fra entrata ed uscita, con percentuali variabili fra il 33 ed il 62 %. Percentuali di abbattimento non elevate sono giustificate dallo scarso grado di maturazione dei siti monitorati, in molti casi recentemente convertiti a Fascia Tampone. Ancora una volta si conferma l’estrema eterogeneità delle risposte di questi sistemi ed il ruolo prioritario delle forzanti idrologiche nel determinarne l’efficacia. Seven buffer strips (BS adjacent to fresh water bodies, realized according to the technical data contained in the Standard 5

Buffer management in wireless full-duplex systems

KAUST Repository

Bouacida, Nader

2015-10-19

Wireless full-duplex radios can simultaneously transmit and receive using the same frequency. In theory, this can double the throughput. In fact, there is only little work addressing aspects other than throughput gains in full-duplex systems. Over-buffering in today\\'s networks or the so-called “bufferbloat” phenomenon creates excessive end-to-end delays resulting in network performance degradation. Our analysis shows that full-duplex systems may suffer from high latency caused by bloated buffers. In this paper, we address the problem of buffer management in full-duplex networks by using Wireless Queue Management (WQM), which is an active queue management technique for wireless networks. Our solution is based on Relay Full-Duplex MAC (RFD-MAC), an asynchronous media access control protocol designed for relay full-duplexing. We compare the performance of WQM in full-duplex environment to Drop Tail mechanism over various scenarios. Our solution reduces the end-to-end delay by two orders of magnitude while achieving similar throughput in most of the cases.

Comparative study of buffered 50% glycolic acid (pH 3.0) + 0.5% salicylic acid solution vs Jessner's solution in patients with acne vulgaris.

Science.gov (United States)

In Jae, Jeong; Dong Ju, Hyun; Dong Hyun, Kim; Yoon, Moon Soo; Lee, Hee Jung

2017-11-21

Superficial chemical peels are frequently used in acne vulgaris treatment. Although glycolic acid (GA) has been widely used in clinical practice, its pH ranges from 0.08-2.75 and thus should be neutralized after application to avoid burns. To evaluate treatment efficacy and safety of chemical peeling using buffered 50% GA (pH 3.0) + 0.5% salicylic acid (SA) solution that does not need to be neutralized in the treatment of acne vulgaris compared to the conventional peeling using Jessner's solution. We performed a prospective, randomized, evaluator-blind, split-face clinical trial. Twenty patients were randomized by assigning one side of each patient's face to receive a 50% GA (pH 3.0) + 0.5% SA peel (GA side) and the other side to receive the Jessner's solution (Jessner's solution side). All patients underwent 2 sessions of treatment spaced 2 weeks apart. Lesion count, acne severity, subjective efficacy assessment, and side effects were evaluated. The total lesion count was significantly reduced for the GA and Jessner's solution sides (P  .05). The GA side had fewer side effects than the Jessner's solution side. The results of this study suggest that chemical peeling using the 50% GA (pH 3.0) + 0.5% SA solution can be as effective and convenient as the conventional peeling using Jessner's solution in the treatment of acne vulgaris and may show fewer adverse events than the conventional peeling. © 2017 Wiley Periodicals, Inc.

Similarity of salt influences on the pH of buffers, polyelectrolytes, and proteins.

Science.gov (United States)

Voinescu, Alina E; Bauduin, Pierre; Pinna, M Cristina; Touraud, Didier; Ninham, Barry W; Kunz, Werner

2006-05-04

Changes in pH induced by the addition of electrolytes to buffers, polyelectrolytes (a polycarboxy polymethylene and a polyethyleneimine), and proteins (casein, whey, and lysozyme) solutions are explored systematically. The two buffer systems are triethanolamine/triethanolammonium chloride and citric acid/sodium citrate. These are chosen because of the similarity of their acid-base equilibria with those of amino acids predominant in most proteins, that is, amino acids that include carboxylate or ammonium groups in their structures. The pH of triethanolamine and of citrate buffers respectively increases and decreases when salt is added. At low electrolyte concentrations (buffer solutions. It is even possible to qualitatively predict these changes in protein solutions simply from the primary protein structure. At least in the systems considered here, the specific ion effects on pH seem to correlate with the bulk activity coefficients of the added electrolytes, at least at moderate salt concentrations.

Standardization of {sup 32}P radioactive solution

Energy Technology Data Exchange (ETDEWEB)

Marques, Caio Pinheiros; Koskinas, Marina Fallone; Almeida, Jamille da Silveira; Yamazaki, Ione M.; Dias, Mauro da Silva, E-mail: cpmarques@usp.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2016-07-01

The standardization of {sup 32}P radioactive solution using three different methods is presented. The disintegration rate was determined by the CIEMAT/NIST and TDCR methods in liquid scintillator systems and self-absorption extrapolation method using 4π(PC)-β system. The results obtained for the activity of the {sup 32}P solution were compared and they agree within the experimental uncertainties. (author)

Buffer moisture protection system

International Nuclear Information System (INIS)

Ritola, J.; Peura, J.

2013-11-01

With the present knowledge, bentonite blocks have to be protected from the air relative humidity and from any moisture leakages in the environment that might cause swelling of the bentonite blocks during the 'open' installation phase before backfilling. The purpose of this work was to design the structural reference solution both for the bottom of the deposition hole and for the buffer moisture protection and dewatering system with their integrated equipment needed in the deposition hole. This report describes the Posiva's reference solution for the buffer moisture protection system and the bottom plate on basis of the demands and functional requirements set by long-term safety. The reference solution with structural details has been developed in research work made 2010-2011. The structural solution of the moisture protection system has not yet been tested in practice. On the bottom of the deposition hole a copper plate which protects the lowest bentonite block from the gathered water is installed straight to machined and even rock surface. The moisture protection sheet made of EPDM rubber is attached to the copper plate with an inflatable seal. The upper part of the moisture protection sheet is fixed to the collar structures of the lid which protects the deposition hole in the disposal tunnel. The main function of the moisture protection sheet is to protect bentonite blocks from the leaking water and from the influence of the air humidity at their installation stage. The leaking water is controlled by the dewatering and alarm system which has been integrated into the moisture protection liner. (orig.)

Moisture Buffer Value of Building Materials

DEFF Research Database (Denmark)

Rode, Carsten; Peuhkuri, Ruut; Time, Berit

2007-01-01

When building materials are in contact with indoor air they have some effect to moderate the variations of indoor humidity in occupied buildings. But so far there has been a lack of a standardized quantity to characterize the moisture buffering capability of materials. It has been the objective o...... is a test protocol which expresses how materials should be tested for determination of their Moisture Buffer Value. Finally, the paper presents some of the results of a Round Robin Test on various typical building materials that has been carried out in the project....... of a recent Nordic project to define such a quantity, and to declare it in the form of a NORDTEST method. The Moisture Buffer Value is the figure that has been developed in the project as a way to appraise the moisture buffer effect of materials, and the value is described in the paper. Also explained...

Labile synthetic cadmium complexes are not bioavailable to Pseudokirchneriella subcapitata in resin buffered solutions

Energy Technology Data Exchange (ETDEWEB)

Verheyen, L., E-mail: Liesbeth.Verheyen@ees.kuleuven.be [Division of Soil and Water Management, K.U. Leuven, Kasteelpark Arenberg 20, Box 2459, 3001 Heverlee (Belgium); Merckx, R. [Division of Soil and Water Management, K.U.Leuven, Kasteelpark Arenberg 20, Box 2459, 3001 Heverlee (Belgium); Smolders, E., E-mail: Erik.Smolders@ees.kuleuven.be [Division of Soil and Water Management, K.U. Leuven, Kasteelpark Arenberg 20, Box 2459, 3001 Heverlee (Belgium)

2012-11-15

The Free Ion Activity Model (FIAM) predicts that cadmium (Cd) uptake by organisms is identical for solutions with the same free Cd{sup 2+} concentration and inorganic composition. Clear exceptions to the FIAM have been shown for Cd uptake by plant roots, periphyton and human cells where labile Cd complexes increase bioavailability and which has been attributed to their role in enhancing Cd diffusion towards the uptake cells. Here, we assessed the role of labile Cd complexes on Cd uptake by algae, for which diffusion limitations should be less pronounced due to their smaller size. Long-term (3 days) Cd uptake by the green algae Pseudokirchneriella subcapitata was measured in resin buffered solutions with or without synthetic ligands and at three Cd{sup 2+} ion activities (pCd 8.2-5.7). The free Cd{sup 2+} activity was maintained during the test using a metal-selective resin located in the algal bottles. Total dissolved Cd increased up to 35-fold by adding the synthetic ligands at constant Cd{sup 2+} activity. In contrast, Cd uptake by algae increased maximally 2.8 fold with increasing concentration of the synthetic ligands and the availability of the complexes were maximally 5.2% relative to Cd{sup 2+} for NTA and CDTA complexes. It is concluded that labile Cd complexes do not greatly enhance Cd bioavailability to the unicellular algae and calculations suggest that Cd transport from solution to these small cells is not rate limiting.

Labile synthetic cadmium complexes are not bioavailable to Pseudokirchneriella subcapitata in resin buffered solutions

International Nuclear Information System (INIS)

Verheyen, L.; Merckx, R.; Smolders, E.

2012-01-01

The Free Ion Activity Model (FIAM) predicts that cadmium (Cd) uptake by organisms is identical for solutions with the same free Cd 2+ concentration and inorganic composition. Clear exceptions to the FIAM have been shown for Cd uptake by plant roots, periphyton and human cells where labile Cd complexes increase bioavailability and which has been attributed to their role in enhancing Cd diffusion towards the uptake cells. Here, we assessed the role of labile Cd complexes on Cd uptake by algae, for which diffusion limitations should be less pronounced due to their smaller size. Long-term (3 days) Cd uptake by the green algae Pseudokirchneriella subcapitata was measured in resin buffered solutions with or without synthetic ligands and at three Cd 2+ ion activities (pCd 8.2–5.7). The free Cd 2+ activity was maintained during the test using a metal-selective resin located in the algal bottles. Total dissolved Cd increased up to 35-fold by adding the synthetic ligands at constant Cd 2+ activity. In contrast, Cd uptake by algae increased maximally 2.8 fold with increasing concentration of the synthetic ligands and the availability of the complexes were maximally 5.2% relative to Cd 2+ for NTA and CDTA complexes. It is concluded that labile Cd complexes do not greatly enhance Cd bioavailability to the unicellular algae and calculations suggest that Cd transport from solution to these small cells is not rate limiting.

Enhancement of Self Efficacy of Vocational School Students in Buffer Solution Topics through Guided Inquiry Learning

Science.gov (United States)

M, Ardiany; W, Wahyu; A, Supriatna

2017-09-01

The more students who feel less confident in learning, so doing things that are less responsible, such as brawl, drunkenness and others. So researchers need to do research related to student self efficacy in learning, in order to reduce unwanted things. This study aims to determine the effect of guided inquiry learning on improving self-efficacy of learners in the buffer solution topics. The method used is the mixed method which is the two group pretest postest design. The subjects of the study are 60 students of class XI AK in one of the SMKN in Bandung, consisting of 30 experimental class students and 30 control class students. The instruments used in this study mix method consist of self-efficacy questionnaire of pretest and posttest learners, interview guides, and observation sheet. Data analysis using t test with significant α = 0,05. Based on the result of inquiry of guided inquiry study, there is a significant improvement in self efficacy aspect of students in the topic of buffer solution. Data of pretest and posttest interview, observation, questionnaire showed significant result, that is improvement of experimental class with conventionally guided inquiry learning. The mean of self-efficacy of student learning there is significant difference of experiment class than control class equal to 0,047. There is a significant relationship between guided inquiry learning with self efficacy and guided inquiry learning. Each correlation value is 0.737. The learning process with guided inquiry is fun and challenging so that students can expose their ideas and opinions without being forced. From the results of questionnaires students showed an attitude of interest, sincerity and a good response of learning. While the results of questionnaires teachers showed that guided inquiry learning can make students learn actively, increased self-efficacy.

Complexation of buffer constituents with neutral complexation agents: part I. Impact on common buffer properties.

Science.gov (United States)

Riesová, Martina; Svobodová, Jana; Tošner, Zdeněk; Beneš, Martin; Tesařová, Eva; Gaš, Bohuslav

2013-09-17

The complexation of buffer constituents with the complexation agent present in the solution can very significantly influence the buffer properties, such as pH, ionic strength, or conductivity. These parameters are often crucial for selection of the separation conditions in capillary electrophoresis or high-pressure liquid chromatography (HPLC) and can significantly affect results of separation, particularly for capillary electrophoresis as shown in Part II of this paper series (Beneš, M.; Riesová, M.; Svobodová, J.; Tesařová, E.; Dubský, P.; Gaš, B. Anal. Chem. 2013, DOI: 10.1021/ac401381d). In this paper, the impact of complexation of buffer constituents with a neutral complexation agent is demonstrated theoretically as well as experimentally for the model buffer system composed of benzoic acid/LiOH or common buffers (e.g., CHES/LiOH, TAPS/LiOH, Tricine/LiOH, MOPS/LiOH, MES/LiOH, and acetic acid/LiOH). Cyclodextrins as common chiral selectors were used as model complexation agents. We were not only able to demonstrate substantial changes of pH but also to predict the general complexation characteristics of selected compounds. Because of the zwitterion character of the common buffer constituents, their charged forms complex stronger with cyclodextrins than the neutral ones do. This was fully proven by NMR measurements. Additionally complexation constants of both forms of selected compounds were determined by NMR and affinity capillary electrophoresis with a very good agreement of obtained values. These data were advantageously used for the theoretical descriptions of variations in pH, depending on the composition and concentration of the buffer. Theoretical predictions were shown to be a useful tool for deriving some general rules and laws for complexing systems.

Providers and Patients Caught Between Standardization and Individualization: Individualized Standardization as a Solution

Science.gov (United States)

Ansmann, Lena; Pfaff, Holger

2018-01-01

In their 2017 article, Mannion and Exworthy provide a thoughtful and theory-based analysis of two parallel trends in modern healthcare systems and their competing and conflicting logics: standardization and customization. This commentary further discusses the challenge of treatment decision-making in times of evidence-based medicine (EBM), shared decision-making and personalized medicine. From the perspective of systems theory, we propose the concept of individualized standardization as a solution to the problem. According to this concept, standardization is conceptualized as a guiding framework leaving room for individualization in the patient physician interaction. The theoretical background is the concept of context management according to systems theory. Moreover, the comment suggests multidisciplinary teams as a possible solution for the integration of standardization and individualization, using the example of multidisciplinary tumor conferences and highlighting its limitations. The comment also supports the authors’ statement of the patient as co-producer and introduces the idea that the competing logics of standardization and individualization are a matter of perspective on macro, meso and micro levels. PMID:29626403

Liquid chromatography-tandem mass spectrometry for analysis of intestinal permeability of loperamide in physiological buffer.

Directory of Open Access Journals (Sweden)

Miriam S Rubelt

Full Text Available Analysis of in vitro samples with high salt concentrations represents a major challenge for fast and specific quantification with liquid chromatography-tandem mass spectrometry (LC-MS/MS. To investigate the intestinal permeability of opioids in vitro employing the Ussing chamber technique, we developed and validated a fast, sensitive and selective method based on LC-MS/MS for the determination of loperamide in HEPES-buffered Ringer's solution. Chromatographic separation was achieved with an Atlantis dC18 column, 2.1 mm×20 mm, 3 µm particle size and a gradient consisting of methanol/0.1% formic acid and ammonium acetate. The flow rate was 0.7 ml/min, and the total run time was 3 min. For quantification, two mass transitions for loperamide and a deuterated internal standard (methadone-d(3 were used. The lower limit of loperamide quantification was 0.2 ng/ml. This new LC-MS/MS method can be used for the detection of loperamide in any experimental setup using HEPES-buffered Ringer's solution as a matrix compound.

Analysis of diffusive mass transport in a cracked buffer

International Nuclear Information System (INIS)

Garisto, N.C.; Garisto, F.

1989-11-01

In the disposal vault design for the Canadian Nuclear Fuel Waste Management Program, cylindrical containers of used nuclear fuel would be placed in vertical boreholes in rock and surrounded with a bentonite-based buffer material. The buffer is expected to absorb and/or retard radionuclides leaching from the fuel after the containers fail. There is some evidence, however, that the buffer may be susceptible to cracking. In this report we investigate numerically the consequences of cracking on uranium diffusion through the buffer. The derivation of the mass-transport equations and the numerical solution method are presented for the solubility-limited diffusion of uranium in a cracked buffer system for both swept-away and semi-impermeable boundary conditions at the rock-buffer interface. The results indicate that for swept-away boundary conditions the total uranium flux through the cracked buffer system is, as expected, greater than through the uncracked buffer. The effect of the cracks is strongly dependent on the ratio D/D eff , where D and D eff are the pore-water and the effective buffer diffusion coefficient, respectively. However, although a decrease in D eff enhances the effect of cracks on the total cumulative flux (relative to the uncracked buffer), it also decreases the total cumulative flux through the cracked buffer system (relative to a cracked buffer with a larger D eff value). Finally, for semi-impermeable boundary conditions, the effect of cracks on the total radionuclide flux is relatively small

Religion as problem, religion as solution: religious buffers of the links between religious/spiritual struggles and well-being/mental health.

Science.gov (United States)

Abu-Raiya, Hisham; Pargament, Kenneth I; Krause, Neal

2016-05-01

Previous studies have established robust links between religious/spiritual struggles (r/s struggles) and poorer well-being and psychological distress. A critical issue involves identifying the religious factors that buffer this relationship. This is the first study to empirically address this question. Specifically, it examines four religious factors (i.e., religious commitment, life sanctification, religious support, religious hope) as potential buffers of the links between r/s struggle and one indicator of subjective well-being (i.e., happiness) and one indicator of psychological distress (i.e., depressive symptoms). We utilized a cross-sectional design and a nationally representative sample of American adults (N = 2140) dealing with a wide range of major life stressors. We found that the interactions between r/s struggle and all potential moderators were significant in predicting happiness and/or depression. The linkage between r/s struggle and lower levels of happiness was moderated by higher levels of each of the four proposed religious buffers. Religious commitment and life sanctification moderated the ties between r/s struggles and depressive symptoms. The findings underscore the multifaceted character of religion: Paradoxically, religion may be a source of solutions to problems that may be an inherent part of religious life.

Prevention of passive film breakdown on iron in a borate buffer solution containing chloride ion by coverage with a self-assembled monolayer of hexadecanoate ion

International Nuclear Information System (INIS)

Aramaki, Kunitsugu; Shimura, Tadashi

2003-01-01

Breakdown of a passive film on iron in a borate buffer solution (pH 8.49) containing 0.1 M of Cl - was suppressed by coverage of the passive film surface with a self-assembled monolayer (SAM) of hexadecanoate ion C 15 H 31 CO 2 - (C 16 A - ). The pitting potential of an iron electrode previously passivated in the borate buffer at 0.50 V/SCE increased by treatment in an aqueous solution of sodium hexadecanoate for many hours, indicating protection of the passive film from breakdown caused by an attack on defects of the film with Cl - . No breakdown occurred over the potential range of the passive region by coverage with the SAM of C 16 A - in some cases. Structures of the passive film and the monolayer were characterized by X-ray photoelectron and Fourier transform infrared reflection spectroscopies and contact angle measurement with a drop of water

Buffer management in wireless full-duplex systems

KAUST Repository

Bouacida, Nader; Showail, Ahmad; Shihada, Basem

2015-01-01

, we address the problem of buffer management in full-duplex networks by using Wireless Queue Management (WQM), which is an active queue management technique for wireless networks. Our solution is based on Relay Full-Duplex MAC (RFD

Solution-processed In2S3 buffer layer for chalcopyrite thin film solar cells

Science.gov (United States)

Wang, Lan; Lin, Xianzhong; Ennaoui, Ahmed; Wolf, Christian; Lux-Steiner, Martha Ch.; Klenk, Reiner

2016-02-01

We report a route to deposit In2S3 thin films from air-stable, low-cost molecular precursor inks for Cd-free buffer layers in chalcopyrite-based thin film solar cells. Different precursor compositions and processing conditions were studied to define a reproducible and robust process. By adjusting the ink properties, this method can be applied in different printing and coating techniques. Here we report on two techniques, namely spin-coating and inkjet printing. Active area efficiencies of 12.8% and 12.2% have been achieved for In2S3-buffered solar cells respectively, matching the performance of CdS-buffered cells prepared with the same batch of absorbers.

Solution standards for quality control of nuclear-material analytical measurements

International Nuclear Information System (INIS)

Clark, J.P.

1981-01-01

Analytical chemistry measurement control depends upon reliable solution standards. At the Savannah River Plant Control Laboratory over a thousand analytical measurements are made daily for process control, product specification, accountability, and nuclear safety. Large quantities of solution standards are required for a measurement quality control program covering the many different analytical chemistry methods. Savannah River Plant produced uranium, plutonium, neptunium, and americium metals or oxides are dissolved to prepare stock solutions for working or Quality Control Standards (QCS). Because extensive analytical effort is required to characterize or confirm these solutions, they are prepared in large quantities. These stock solutions are diluted and blended with different chemicals and/or each other to synthesize QCS that match the matrices of different process streams. The target uncertainty of a standard's reference value is 10% of the limit of error of the methods used for routine measurements. Standard Reference Materials from NBS are used according to special procedures to calibrate the methods used in measuring the uranium and plutonium standards so traceability can be established. Special precautions are required to minimize the effects of temperature, radiolysis, and evaporation. Standard reference values are periodically corrected to eliminate systematic errors caused by evaporation or decay products. Measurement control is achieved by requiring analysts to analyze a blind QCS each shift a measurement system is used on plant samples. Computer evaluation determines whether or not a measurement is within the +- 3 sigma control limits. Monthly evaluations of the QCS measurements are made to determine current bias correction factors for accountability measurements and detect significant changes in the bias and precision statistics. The evaluations are also used to plan activities for improving the reliability of the analytical chemistry measurements

Solution-processed In2S3 buffer layer for chalcopyrite thin film solar cells

Directory of Open Access Journals (Sweden)

Wang Lan

2016-01-01

Full Text Available We report a route to deposit In2S3 thin films from air-stable, low-cost molecular precursor inks for Cd-free buffer layers in chalcopyrite-based thin film solar cells. Different precursor compositions and processing conditions were studied to define a reproducible and robust process. By adjusting the ink properties, this method can be applied in different printing and coating techniques. Here we report on two techniques, namely spin-coating and inkjet printing. Active area efficiencies of 12.8% and 12.2% have been achieved for In2S3-buffered solar cells respectively, matching the performance of CdS-buffered cells prepared with the same batch of absorbers.

Lessons learned in streamlining the preparation of SNM standard solutions

International Nuclear Information System (INIS)

Clark, J.P.; Johnson, S.R.

1986-01-01

Improved safeguard measurements have produced a demand for greater quantities of reliable SNM solution standards. At the Savannah River Plant (SRP), the demand for these standards has been met by several innovations to improve the productivity and reliability of standards preparations. With the use of computer controlled balance, large batches of SNM stock solutions are prepared on a gravimetric basis. Accurately dispensed quantities of the stock solution are weighed and stored in bottles. When needed, they are quantitatively transferred to tared containers, matrix adjusted to target concentrations, weighed, and measured for density at 25 0 C. Concentrations of SNM are calculated both gravimetrically and volumetrically. Calculated values are confirmed analytically before the standards are used in measurement control program (MCP) activities. The lessons learned include: MCP goals include error identification and management. Strategy modifications are required to improve error management. Administrative controls can minimize certain types of errors. Automation can eliminate redundancy and streamline preparations. Prudence and simplicity enhance automation success. The effort expended to increase productivity has increased the reliability of standards and provided better documentation for quality assurance

Carbon dioxide dissociation and buffering in chicken blood during development.

Science.gov (United States)

Tazawa, H; Piiper, J

1984-07-01

Carbon dioxide dissociation curves of oxygenated and deoxygenated bloods, the Haldane effect, the buffer value and other blood and true plasma buffering indices, O2 capacity and hematocrit were determined in bloods withdrawn from chicks before, during and after hatching and 8-month-old hens. Blood CO2 dissociation curves shifted upwards in the developing embryo till pipping, and moved downwards after pipping and hatching. In accordance with the position of the CO2 dissociation curves, the true plasma bicarbonate and red cell CO2 standardized to PCO2 = 40 torr changed. The Haldane factor at standard PCO2 increased from 0.12-0.13 on days 10-14 of incubation to 0.34 in young hens. The buffering power changed in parallel with O2 capacity and hematocrit, increasing steadily during incubation, dropping at hatching and then increasing again to the adult value. The observed changes in the CO2 dissociation curves and buffering variables during the development enable the chick to minimize the changes in the acid-base status and are favorable for coping with the increasing demand for CO2 transport and buffering of the developing bird.

The preparation of primary standard solutions for each of the noble metals

International Nuclear Information System (INIS)

Mallett, R.C.; Wall, G.J.; Jones, E.A.; Royal, S.J.

1977-01-01

A revised method for the preparation of primary standard solutions for each of the noble metals is described. It is now recommended that standard noble-metal solutions should be made from the pure metals and not from salts as previously described. Metals should have a certified purity of 99,95 per cent or better, and the purity should be confirmed by analysis, the techniques of emission spectography or spark-source mass spectrography being used. After the metals have been dissolved, the solutions are made up to volume and the metal content of the standard solutions is checked. For most instrumental techniques for which the standards are intended, the check analysis should be within 0,3 per cent of the certified value

Regenerative, Highly-Sensitive, Non-Enzymatic Dopamine Sensor and Impact of Different Buffer Systems in Dopamine Sensing

Directory of Open Access Journals (Sweden)

Saumya Joshi

2018-01-01

Full Text Available Carbon nanotube field-effect transistors are used extensively in ultra-sensitive biomolecule sensing applications. Along with high sensitivity, the possibility of regeneration is highly desired in bio-sensors. An important constituent of such bio-sensing systems is the buffer used to maintain pH and provide an ionic conducting medium, among its other properties. In this work, we demonstrate highly-sensitive regenerative dopamine sensors and the impact of varying buffer composition and type on the electrolyte gated field effect sensors. The role of the buffer system is an often ignored condition in the electrical characterization of sensors. Non-enzymatic dopamine sensors are fabricated and regenerated in hydrochloric acid (HCl solution. The sensors are finally measured against four different buffer solutions. The impact of the nature and chemical structure of buffer molecules on the dopamine sensors is shown, and the appropriate buffer systems are demonstrated.

Preparation of uranium standard solutions for x-ray fluorescence analysis

International Nuclear Information System (INIS)

Wong, C.M.; Cate, J.L.; Pickles, W.L.

1978-03-01

A method has been developed for gravimetrically preparing uranium nitrate standards with an estimated mean error of 0.1% (1 sigma) and a maximum error of 0.2% (1 sigma) for the total uranium weight. Two source materials, depleted uranium dioxide powder and NBS Standard Reference Material 960 uranium metal, were used to prepare stock solutions. The NBS metal proved to be superior because of the small but inherent uncertainty in the stoichiometry of the uranium oxide. These solutions were used to prepare standards in a freeze-dried configuration suitable for x-ray fluorescence analysis. Both gravimetric and freeze-drying techniques are presented. Volumetric preparation was found to be unsatisfactory for 0.1% precision for the sample size of interest. One of the primary considerations in preparing uranium standards for x-ray fluorescence analysis is the development of a technique for dispensing a 50-μl aliquot of a standard solution with a precision of 0.1% and an accuracy of 0.1%. The method developed corrects for variation in aliquoting and for evaporation loss during weighing. Two sets, each containing 50 standards have been produced. One set has been retained by LLL and one set retained by the Savannah River project

High-performance liquid chromatographic analysis of methadone hydrochloride oral solution.

Science.gov (United States)

Beasley, T H; Ziegler, H W

1977-12-01

A direct and rapid high-performance liquid chromatographic assay for methadone hydrochloride in a flavored oral solution dosage form is described. A syrup sample, one part diluted with three parts of water, is introduced onto a column packed with octadecylsilane bonded on 10 micrometer porous silica gel (reversed phase). A formic acid-ammonium formate-buffered mobile phase is linear programmed with acetonitrile. The absorbance is monitored continuously at 280 or 254 nm, using a flow-through, UV, double-beam photometer. An aqueous methadone hydrochloride solution is used for external standardization. The relative standard deviation was not more than 1.0%. Drug recovery from a syrup base was better than 99.8%.

Towards Optimal Buffer Size in Wi-Fi Networks

KAUST Repository

Showail, Ahmad

2016-01-01

extensively for wired networks. However, there is little work addressing the unique challenges of wireless environment. In this dissertation, we discuss buffer sizing challenges in wireless networks, classify the state-of-the-art solutions, and propose two

Traveling waves in the discrete fast buffered bistable system.

Science.gov (United States)

Tsai, Je-Chiang; Sneyd, James

2007-11-01

We study the existence and uniqueness of traveling wave solutions of the discrete buffered bistable equation. Buffered excitable systems are used to model, among other things, the propagation of waves of increased calcium concentration, and discrete models are often used to describe the propagation of such waves across multiple cells. We derive necessary conditions for the existence of waves, and, under some restrictive technical assumptions, we derive sufficient conditions. When the wave exists it is unique and stable.

Addressing a Common Misconception: Ammonium Acetate as Neutral pH "Buffer" for Native Electrospray Mass Spectrometry

Science.gov (United States)

Konermann, Lars

2017-09-01

Native ESI-MS involves the transfer of intact proteins and biomolecular complexes from solution into the gas phase. One potential pitfall is the occurrence of pH-induced changes that can affect the analyte while it is still surrounded by solvent. Most native ESI-MS studies employ neutral aqueous ammonium acetate solutions. It is a widely perpetuated misconception that ammonium acetate buffers the analyte solution at neutral pH. By definition, a buffer consists of a weak acid and its conjugate weak base. The buffering range covers the weak acid pKa ± 1 pH unit. NH4 + and CH3-COO- are not a conjugate acid/base pair, which means that they do not constitute a buffer at pH 7. Dissolution of ammonium acetate salt in water results in pH 7, but this pH is highly labile. Ammonium acetate does provide buffering around pH 4.75 (the pKa of acetic acid) and around pH 9.25 (the pKa of ammonium). This implies that neutral ammonium acetate solutions electrosprayed in positive ion mode will likely undergo acidification down to pH 4.75 ± 1 in the ESI plume. Ammonium acetate nonetheless remains a useful additive for native ESI-MS. It is a volatile electrolyte that can mimic the solvation properties experienced by proteins under physiological conditions. Also, a drop from pH 7 to around pH 4.75 is less dramatic than the acidification that would take place in pure water. It is hoped that the habit of referring to pH 7 solutions as ammonium acetate "buffer" will disappear from the literature. Ammonium acetate "solution" should be used instead. [Figure not available: see fulltext.

Anodic characteristics and stress corrosion cracking behavior of nickel rich alloys in bicarbonate and buffer solutions

International Nuclear Information System (INIS)

Zadorozne, Natalia S.; Giordano, Mabel C.; Ares, Alicia E.; Carranza, Ricardo M.; Rebak, Raul B.

2016-01-01

Highlights: • We investigate which element in alloy C-22 may be responsible for the cracking susceptibility of the high nickel alloy. • Six nickel based alloys with different amount of Cr and Mo were selected for the electrochemical tests and response to SSRT. • Polarization tests showed that an anodic peak appear in the passive region in Cr containing alloys. • Cracking of Ni alloys in carbonate solutions seem to be a consequence of the instability of the passivating chromium oxide. • Alloys containing both Cr and Mo have the highest susceptibility. - Abstract: The aim of this work is to investigate which alloying element in C-22 is responsible for the cracking susceptibility of the alloy in bicarbonate and two buffer solutions (tungstate and borate). Six nickel based alloys, with different amount of chromium (Cr) and molybdenum (Mo) were tested using electrochemical methods and slow strain rate tests (SSRT) at 90 °C. All Cr containing alloys had transgranular cracking at high anodic potential; however, C-22 containing high Cr and high Mo was the most susceptible alloy to cracking. Bicarbonate was the most aggressive of three tested environments of similar pH.

Buffer salt effects in off-line coupling of capillary electrophoresis and mass spectrometry.

Science.gov (United States)

Marák, Jozef; Stanová, Andrea

2014-05-01

In this work, the impact of buffer salts/matrix effects on the signal in direct injection MS with an electrospray interface (DI-ESI-MS) following pITP fractionation of the sample was studied. A range of buffers frequently used in CE analyses (pH 3-10) was prepared containing 10, 50, and 90% v/v of ACN, respectively. The sets of calibration solutions of cetirizine (an antihistaminic drug with an amphiprotic character) within a 0.05-2.0 mg/L concentration range were prepared in different buffers. The greatest enhancements in the MS signal (in terms of change in the slope of the calibration line) were obtained for the beta-alanine buffer (pH 3.5) in positive ionization and for the borate buffer (pH 9.2) in negative ionization, respectively. The procedure was successfully applied to the analysis of buserelin (a peptidic drug). The slope of the calibration line for solutions containing the beta-alanine buffer with 50% of ACN was 4 times higher than for water or urine, respectively. This study clearly demonstrates that the buffer salt/matrix effects in an offline combination of pITP and DI-ESI-MS can also play a positive role, as they can enhance the signal in MS. A similar influence of the above effects can also be presumed in the CE techniques combined on-line with ESI-MS.

Effect of a New Local Anesthetic Buffering Device on Pain Reduction During Nerve Block lnjections

Science.gov (United States)

2014-07-10

the anticipation of pain associated with dental care is a significant deterrent in seeking treatment. With the advent of modern local anesthesia ...eliminate pain from dental injection to include: application of topical anesthesia , tissue pressure/vibration, cold application, and buffering of the local ...anesthetic solution. In dentistry , the effect of buffering local anesthetic solutions was first studied by Gros and Laewen in 1910 and then by

Development of a novel running buffer for the simultaneous determination of nitrate and nitrite in human serum by capillary zone electrophoresis.

Science.gov (United States)

Miyado, Takashi; Nagai, Hidenori; Takeda, Sahori; Saito, Keiitsu; Fukushi, Keiichi; Yoshida, Yasukazu; Wakida, Shin-ichi; Niki, Etsuo

2003-10-03

In order to improve NO2- peak height and obtain a convenient buffer system for the assay of nitrogen monooxide metabolites, we developed a novel running buffer for the simultaneous determination of nitrite and nitrate in human serum by capillary electrophoresis. The addition of cetyltrimethylammonium chloride to the running buffer resulted in high-speed separation using reverse electroosmotic flow. Highly sensitive determination was also achieved using stacking with 10-fold diluted sample solutions. The samples were injected hydrodynamically for 100 s into a 50 cm x 75 microm I.D. capillary. The separation voltage was 10 kV (negative polarity). UV detection was performed at 214 nm. We obtained complete separation of nitrite and nitrate in deproteinized human serum within 6 min with optimum analytical conditions. Linear calibration curves for nitrite and nitrate for both peak height and peak area were obtained with standard addition method. The limits of detection obtained at a signal-to-noise ratio of 3 for nitrite and nitrate were 4.1 and 2.0 microM, while the values of relative standard deviation of peak height were 2.4 and 2.6%, respectively.

Growth of thick La{sub 2}Zr{sub 2}O{sub 7} buffer layers for coated conductors by polymer-assisted chemical solution deposition

Energy Technology Data Exchange (ETDEWEB)

Zhang, Xin, E-mail: xzhang@my.swjtu.edu.cn [Key Laboratory of Magnetic Levitation Technologies and Maglev Trains, Ministry of Education of China, Superconductivity and New Energy Center (SNEC), Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); School of Electrical Engineering, Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); Zhao, Yong, E-mail: yzhao@swjtu.edu.cn [Key Laboratory of Magnetic Levitation Technologies and Maglev Trains, Ministry of Education of China, Superconductivity and New Energy Center (SNEC), Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); School of Materials Science and Engineering, University of New South Wales, Sydney, 2052 NSW (Australia); Xia, Yudong [State Key Lab of Electronic Thin Films and Integrated Devices, University of Electronic Science and Technology of China, Chengdu 610054 (China); Guo, Chunsheng [Key Laboratory of Magnetic Levitation Technologies and Maglev Trains, Ministry of Education of China, Superconductivity and New Energy Center (SNEC), Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); Cheng, C.H. [School of Materials Science and Engineering, University of New South Wales, Sydney, 2052 NSW (Australia); Zhang, Yong [Key Laboratory of Magnetic Levitation Technologies and Maglev Trains, Ministry of Education of China, Superconductivity and New Energy Center (SNEC), Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); Zhang, Han [Department of Physics, Peking University, Beijing 100871 (China)

2015-06-15

Highlights: • We develops a low-cost and high-efficient technology of fabricating LZO buffer layers. • Sufficient thickness LZO buffer layers have been obtained on NiW (2 0 0) alloy substrate. • Highly biaxially textured YBCO thin film has been deposited on LZO/NiW. - Abstract: La{sub 2}Zr{sub 2}O{sub 7} (LZO) epitaxial films have been deposited on LaAlO{sub 3} (LAO) (1 0 0) single-crystal surface and bi-axially textured NiW (2 0 0) alloy substrate by polymer-assisted chemical solution deposition, and afterwards studied with XRD, SEM and AFM approaches. Highly in-plane and out-of-plane oriented, dense, smooth, crack free and with a sufficient thickness (>240 nm) LZO buffer layers have been obtained on LAO (1 0 0) single-crystal surface; The films deposited on NiW (2 0 0) alloy substrate are also found with high degree in-plane and out-of-plane texturing, good density with pin-hole-free, micro-crack-free nature and a thickness of 300 nm. Highly epitaxial 500 nm thick YBa{sub 2}Cu{sub 3}O{sub 7−x} (YBCO) thin film exhibits the self-field critical current density (Jc) reached 1.3 MA/cm{sup 2} at 77 K .These results demonstrate the LZO epi-films obtained with current techniques have potential to be a buffer layer for REBCO coated conductors.

Interoperable and standard e-Health solution over Bluetooth.

Science.gov (United States)

Martinez, I; Del Valle, P; Munoz, P; Trigo, J D; Escayola, J; Martínez-Espronceda, M; Muñoz, A; Serrano, L; Garcia, J

2010-01-01

The new paradigm of e-Health demands open sensors and middleware components that permit transparent integration and end-to-end interoperability of new personal health devices. The use of standards seems to be the internationally adopted way to solve these problems. This paper presents the implementation of an end-to-end standards-based e-Health solution. This includes ISO/IEEE11073 standard for the interoperability of the medical devices in the patient environment and EN13606 standard for the interoperable exchange of the Electronic Healthcare Record. The design strictly fulfills all the technical features of the most recent versions of both standards. The implemented prototype has been tested in a laboratory environment to demonstrate its feasibility for its further transfer to the healthcare system.

The effect of isochoric freezing on mammalian cells in an extracellular phosphate buffered solution.

Science.gov (United States)

Preciado, J; Rubinsky, B

2018-04-20

Isochoric (constant volume) freezing has been recently suggested as a new method for cell and organ preservation. As a first step in studying the effect of isochoric freezing on mammalian cells, Madin-Darby canine kidney epithelial cells (MDCK), were frozen in an isochoric system, in a simple extracellular phosphate buffered solution to -10 °C (96.5 MPa), - 15 °C (162 MPa) and -20 °C (205 MPa) for 60 and 120 min. Cell membrane integrity and cell metabolism were studied with a Live/Dead cell vitality assay and flow cytometry. We found that cell survival decreases with an increase in pressure (lower temperatures) and time of exposure. For example, 60% of cells survived 60 min at - 10 °C and only 18% survived 120 min at this temperature. Negligible survival was measured at - 20 °C. This study may serve as the baseline towards further research on techniques to optimize the effects of isochoric freezing on living biological matter. Copyright © 2018. Published by Elsevier Inc.

Variation of power generation at different buffer types and conductivities in single chamber microbial fuel cells

KAUST Repository

Nam, Joo-Youn; Kim, Hyun-Woo; Lim, Kyeong-Ho; Shin, Hang-Sik; Logan, Bruce E.

2010-01-01

Microbial fuel cells (MFCs) are operated with solutions containing various chemical species required for the growth of electrochemically active microorganisms including nutrients and vitamins, substrates, and chemical buffers. Many different buffers

Scientific Applications Performance Evaluation on Burst Buffer

KAUST Repository

Markomanolis, George S.

2017-10-19

Parallel I/O is an integral component of modern high performance computing, especially in storing and processing very large datasets, such as the case of seismic imaging, CFD, combustion and weather modeling. The storage hierarchy includes nowadays additional layers, the latest being the usage of SSD-based storage as a Burst Buffer for I/O acceleration. We present an in-depth analysis on how to use Burst Buffer for specific cases and how the internal MPI I/O aggregators operate according to the options that the user provides during his job submission. We analyze the performance of a range of I/O intensive scientific applications, at various scales on a large installation of Lustre parallel file system compared to an SSD-based Burst Buffer. Our results show a performance improvement over Lustre when using Burst Buffer. Moreover, we show results from a data hierarchy library which indicate that the standard I/O approaches are not enough to get the expected performance from this technology. The performance gain on the total execution time of the studied applications is between 1.16 and 3 times compared to Lustre. One of the test cases achieved an impressive I/O throughput of 900 GB/s on Burst Buffer.

Moisture buffer capacity of different insulation materials

DEFF Research Database (Denmark)

Peuhkuri, Ruut Hannele; Rode, Carsten; Hansen, Kurt Kielsgaard

2004-01-01

. In the isothermal tests the material samples were exposed to the same change in the relative humidity of the ambient air on both sides, while the samples were exposed to variations in relative humidity only on the cold side in the non-isothermal tests. The results of these rather different measurement principles...... lead to more durable constructions. In this paper, a large range of very different thermal insulation materials have been tested in specially constructed laboratory facilities to determine their moisture buffer capacity. Both isothermal and nonisothermal experimental set-ups have been used...... are discussed, and different ways are presented how to determine the moisture buffer capacity of the materials using partly standard material parameters and partly parameters determined from the actual measurements. The results so far show that the determination of moisture buffer capacity is very sensitive...

Saline catholytes as alternatives to phosphate buffers in microbial fuel cells

KAUST Repository

Ahn, Yongtae; Logan, Bruce E.

2013-01-01

Highly saline solutions were examined as alternatives to chemical buffers in microbial fuel cells (MFCs). The performance of two-chamber MFCs with different concentrations of saline solutions in the cathode chamber was compared to those with a buffered catholyte (50mM PBS). The use of a NaCl catholyte improved the CE to 43-60% (28% with no membrane) due to a reduction in oxygen transfer into the anolyte. The saline catholyte also reduced the membrane and solution resistance to 23Ω (41Ω without a membrane). The maximum power density of 491mW/m2 (240mM NaCl) was only 17% less than the MFC with 50mM PBS. The decrease in power output with highest salinity was due to reduced proton transfer due to the ion exchange membrane, and pH changes in the two solutions. These results show that MFC performance can be improved by using a saline catholyte without pH control. © 2013 Elsevier Ltd.

Saline catholytes as alternatives to phosphate buffers in microbial fuel cells

KAUST Repository

Ahn, Yongtae

2013-03-01

Highly saline solutions were examined as alternatives to chemical buffers in microbial fuel cells (MFCs). The performance of two-chamber MFCs with different concentrations of saline solutions in the cathode chamber was compared to those with a buffered catholyte (50mM PBS). The use of a NaCl catholyte improved the CE to 43-60% (28% with no membrane) due to a reduction in oxygen transfer into the anolyte. The saline catholyte also reduced the membrane and solution resistance to 23Ω (41Ω without a membrane). The maximum power density of 491mW/m2 (240mM NaCl) was only 17% less than the MFC with 50mM PBS. The decrease in power output with highest salinity was due to reduced proton transfer due to the ion exchange membrane, and pH changes in the two solutions. These results show that MFC performance can be improved by using a saline catholyte without pH control. © 2013 Elsevier Ltd.

Current characteristics of λ -DNA molecules/polystyrene nanoparticles in TBE buffer solution through micro/nanofluidic capillaries under DC electric field

International Nuclear Information System (INIS)

Duan, Yifei; Zhao, Wei; Xue, Jing; Sun, Dan; Wang, Kaige; Wang, Guiren; Bai, Jintao; Li, Junjie; Gu, Changzhi

2017-01-01

In practical applications of biochips and bio-sensors, electrokinetic mechanisms are commonly employed to manipulate single bio-molecules and analyze their characteristics. To accurately and flexibly control the movement of single-molecule within micro/nanofluidic channels which are the basic components of Lab-chips, the current signals in micro/nanocapillaries filled with solutions of DNA molecules or polystyrene (PS) nanoparticles are systematically studied. Experimental results indicate that the current response along the micro/nanocapillaries can be significantly influenced by the diameter of the capillaries and the pH value of the solutions. Specifically, when there is only a pure (TBE) solution, the electric conductance does not monotonically decrease with decreasing the diameter of the capillaries, but slightly increases with decreasing the capillary diameter. When λ -DNA molecules or PS nanoparticles are added into the TBE buffer, the size effect on the electric conductance of the solutions are quite different. Although in the former, the electric conductance behaves differently from that in the pure TBE solution and decreases with the decreasing diameter, in the latter, the change is similar to that in the pure TBE solution. Besides, an abnormal ‘falling’ of the electric conductance is observed in a capillary with diameter of 200 nm. The investigation will significantly enhance the understanding on the electric properties of the solutions of biomolecules and particles in micro/nanofluidics. This is especially helpful for designing functional Lab-chip devices. (paper)

Current characteristics of λ-DNA molecules/polystyrene nanoparticles in TBE buffer solution through micro/nanofluidic capillaries under DC electric field

Science.gov (United States)

Duan, Yifei; Zhao, Wei; Xue, Jing; Sun, Dan; Wang, Kaige; Wang, Guiren; Li, Junjie; Bai, Jintao; Gu, Changzhi

2017-03-01

In practical applications of biochips and bio-sensors, electrokinetic mechanisms are commonly employed to manipulate single bio-molecules and analyze their characteristics. To accurately and flexibly control the movement of single-molecule within micro/nanofluidic channels which are the basic components of Lab-chips, the current signals in micro/nanocapillaries filled with solutions of DNA molecules or polystyrene (PS) nanoparticles are systematically studied. Experimental results indicate that the current response along the micro/nanocapillaries can be significantly influenced by the diameter of the capillaries and the pH value of the solutions. Specifically, when there is only a pure (TBE) solution, the electric conductance does not monotonically decrease with decreasing the diameter of the capillaries, but slightly increases with decreasing the capillary diameter. When λ-DNA molecules or PS nanoparticles are added into the TBE buffer, the size effect on the electric conductance of the solutions are quite different. Although in the former, the electric conductance behaves differently from that in the pure TBE solution and decreases with the decreasing diameter, in the latter, the change is similar to that in the pure TBE solution. Besides, an abnormal ‘falling’ of the electric conductance is observed in a capillary with diameter of 200 nm. The investigation will significantly enhance the understanding on the electric properties of the solutions of biomolecules and particles in micro/nanofluidics. This is especially helpful for designing functional Lab-chip devices.

Effects of hypertonic buffer composition on lymph node uptake and bioavailability of rituximab, after subcutaneous administration.

Science.gov (United States)

Fathallah, Anas M; Turner, Michael R; Mager, Donald E; Balu-Iyer, Sathy V

2015-03-01

The subcutaneous administration of biologics is highly desirable; however, incomplete bioavailability after s.c. administration remains a major challenge. In this work we investigated the effects of excipient dependent hyperosmolarity on lymphatic uptake and plasma exposure of rituximab as a model protein. Using Swiss Webster (SW) mice as the animal model, we compared the effects of NaCl, mannitol and O-phospho-L-serine (OPLS) on the plasma concentration of rituximab over 5 days after s.c. administration. An increase was observed in plasma concentrations in animals administered rituximab in hypertonic buffer solutions, compared with isotonic buffer. Bioavailability, as estimated by our pharmacokinetic model, increased from 29% in isotonic buffer to 54% in hypertonic buffer containing NaCl, to almost complete bioavailability in hypertonic buffers containing high dose OPLS or mannitol. This improvement in plasma exposure is due to the improved lymphatic trafficking as evident from the increase in the fraction of dose trafficked through the lymph nodes in the presence of hypertonic buffers. The fraction of the dose trafficked through the lymphatics, as estimated by the model, increased from 0.05% in isotonic buffer to 13% in hypertonic buffer containing NaCl to about 30% for hypertonic buffers containing high dose OPLS and mannitol. The data suggest that hypertonic solutions may be a viable option for improving s.c. bioavailability. Copyright © 2014 John Wiley & Sons, Ltd.

Electrochemical Behavior of Pure Copper in Phosphate Buffer Solutions: A Comparison Between Micro- and Nano-Grained Copper

Science.gov (United States)

Imantalab, O.; Fattah-alhosseini, A.; Keshavarz, M. K.; Mazaheri, Y.

2016-02-01

In this work, electrochemical behavior of annealed (micro-) and nano-grained pure copper (fabricated by accumulative roll bonding process) in phosphate buffer solutions of various pH values ranging from 10.69 to 12.59 has been studied. Before any electrochemical measurements, evaluation of microstructure was obtained by optical microscope and transmission electron microscopy. To investigate the electrochemical behavior of the samples, the potentiodynamic polarization, Mott-Schottky analysis, and electrochemical impedance spectroscopy (EIS) were carried out. Potentiodynamic polarization plots and EIS measurements revealed that as a result of grain refinement, the passive behavior of the nano-grained sample was improved compared to that of annealed pure copper. Also, Mott-Schottky analysis indicated that the passive films behaved as p-type semiconductors and grain refinement did not change the semiconductor type of passive films.

pH buffers for sea water media based on the total hydrogen ion concentration scale

Science.gov (United States)

Dickson, Andrew G.

1993-01-01

Published e.m.f. values measured using the cell ? where p° = 101.325 kPa, and BH + and B are the conjugate acid-base pairs of 2-aminopyridine, 2-amino-2-hydroxymethyl-1,3-propanediol (tris), tetrahydro-1,4-isoxazine (morpholine), and 2-amino-2-methyl-1, 3-propanediol (bis), have been re-evaluated to assign pH values based on the "total" hydrogen ion concentration scale to equimolal ( m =0.04 mol kg -1) buffer solutions based on these compounds. These pH values are consistent with the best available equilibrium constants for acid-base processes in sea water and such pH buffers can be used as pH calibration standards to measure accurate values for oceanic pH on the "total" hydrogen ion pH scale. In addition, the published e.m.f. results for these various amine bases have been used to calculate their respective acidity constants on this pH scale.

Deuterium markers in CdS and Zn(O,S) buffer layers deposited by solution growth for Cu(In,Ga)Se{sub 2} thin-film solar cells

Energy Technology Data Exchange (ETDEWEB)

Witte, Wolfram; Eicke, Axel; Hariskos, Dimitrios [Zentrum fuer Sonnenenergie und Wasserstoff-Forschung Baden-Wuerttemberg (ZSW), Stuttgart (Germany); Souza, Roger A. de; Martin, Manfred [Institute of Physical Chemistry, RWTH Aachen University (Germany)

2017-12-15

This contribution describes an easy and cheap approach to introduce deuterium (D) as an isotopic marker into the commonly used buffer layer materials CdS and Zn(O,S) for Cu(In,Ga)Se{sub 2} (CIGS) thin-film solar cells. D was successfully incorporated during the growth of Zn(O,S) and CdS buffer layers by chemical bath deposition (CBD) with D{sub 2}O. CIGS solar cells prepared with D-containing buffers grown by CBD exhibit power conversion efficiencies above 16%, that is, the D content has no detrimental effect on the performance or other solar cell parameters of the devices. With depth profiles obtained by time-of-flight secondary ion mass spectrometry (ToF-SIMS) we clearly detect the intentionally incorporated D within the solution-grown Zn(O,S) buffer. Assuming that D is present as OD, we compare the amount of OD within the Zn(O,S) layer with the amount of OH on the surface of the subsequent sputtered (Zn,Mg)O layer. Possible applications and future experiments of the method inserting isotopic markers such as D in functional layers of chalcopyrite-type thin-film solar cells and beyond are discussed. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Redox Buffer Strength

Science.gov (United States)

de Levie, Robert

1999-04-01

The proper functioning of enzymes in bodily fluids requires that the pH be maintained within rather narrow limits. The first line of defense against large pH fluctuations in such fluids is the passive control provided by the presence of pH buffers. The ability of pH buffers to stabilize the pH is indicated by the buffer value b introduced in 1922 by van Slyke. It is equally important for many enzymes that the redox potential is kept within a narrow range. In that case, stability of the potential is most readily achieved with a redox buffer. In this communication we define the redox buffer strength by analogy with acid-base buffer strength.

Thermal stability of tagatose in solution.

Science.gov (United States)

Luecke, Katherine J; Bell, Leonard N

2010-05-01

Tagatose, a monosaccharide similar to fructose, has been shown to behave as a prebiotic. To deliver this prebiotic benefit, tagatose must not degrade during the processing of foods and beverages. The objective of this study was to evaluate the thermal stability of tagatose in solutions. Tagatose solutions were prepared in 0.02 and 0.1 M phosphate and citrate buffers at pHs 3 and 7, which were then held at 60, 70, and 80 degrees C. Pseudo-1st-order rate constants for tagatose degradation were determined. In citrate and phosphate buffers at pH 3, minimal tagatose was lost and slight browning was observed. At pH 7, tagatose degradation rates were enhanced. Degradation was faster in phosphate buffer than citrate buffer. Higher buffer concentrations also increased the degradation rate constants. Enhanced browning accompanied tagatose degradation in all buffer solutions at pH 7. Using the activation energies for tagatose degradation, less than 0.5% and 0.02% tagatose would be lost under basic vat and HTST pasteurization conditions, respectively. Although tagatose does breakdown at elevated temperatures, the amount of tagatose lost during typical thermal processing conditions would be virtually negligible. Practical Application: Tagatose degradation occurs minimally during pasteurization, which may allow for its incorporation into beverages as a prebiotic.

Database on gas migration tests through bentonite buffer material

International Nuclear Information System (INIS)

Tanai, Kenji

2009-02-01

Carbon steel is a candidate material for an overpack for geological disposal of high-level radioactive waste in Japan. The corrosion of the carbon steel overpack in aqueous solution under anoxic conditions will cause the generation of hydrogen gas, which may affect hydrological and mechanical properties of the bentonite buffer. To evaluate such an effect of gas generation, it is necessary to develop a model of gas migration through bentonite buffer material taking account of data obtained from experiments. The gas migration experiments under both unsaturated and saturated conditions have been carried out to clarify the fundamental characteristics of bentonite for gas migration. This report compiles the experimental data obtained from gas migration tests for buffer material which has been conducted by JAEA until December, 2007. A CD-ROM is attached as an appendix. (author)

TRIS buffer in simulated body fluid distorts the assessment of glass-ceramic scaffold bioactivity.

Science.gov (United States)

Rohanová, Dana; Boccaccini, Aldo Roberto; Yunos, Darmawati Mohamad; Horkavcová, Diana; Březovská, Iva; Helebrant, Aleš

2011-06-01

The paper deals with the characterisation of the bioactive phenomena of glass-ceramic scaffold derived from Bioglass® (containing 77 wt.% of crystalline phases Na(2)O·2CaO·3SiO(2) and CaO·SiO(2) and 23 wt.% of residual glass phase) using simulated body fluid (SBF) buffered with tris-(hydroxymethyl) aminomethane (TRIS). A significant effect of the TRIS buffer on glass-ceramic scaffold dissolution in SBF was detected. To better understand the influence of the buffer, the glass-ceramic scaffold was exposed to a series of in vitro tests using different media as follows: (i) a fresh liquid flow of SBF containing tris (hydroxymethyl) aminomethane; (ii) SBF solution without TRIS buffer; (iii) TRIS buffer alone; and (iv) demineralised water. The in vitro tests were provided under static and dynamic arrangements. SBF buffered with TRIS dissolved both the crystalline and residual glass phases of the scaffold and a crystalline form of hydroxyapatite (HAp) developed on the scaffold surface. In contrast, when TRIS buffer was not present in the solutions only the residual glassy phase dissolved and an amorphous calcium phosphate (Ca-P) phase formed on the scaffold surface. It was confirmed that the TRIS buffer primarily dissolved the crystalline phase of the glass-ceramic, doubled the dissolving rate of the scaffold and moreover supported the formation of crystalline HAp. This significant effect of the buffer TRIS on bioactive glass-ceramic scaffold degradation in SBF has not been demonstrated previously and should be considered when analysing the results of SBF immersion bioactivity tests of such systems. Copyright © 2011 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Protein buffering in model systems and in whole human saliva.

Directory of Open Access Journals (Sweden)

Andreas Lamanda

Full Text Available The aim of this study was to quantify the buffer attributes (value, power, range and optimum of two model systems for whole human resting saliva, the purified proteins from whole human resting saliva and single proteins. Two model systems, the first containing amyloglucosidase and lysozyme, and the second containing amyloglucosidase and alpha-amylase, were shown to provide, in combination with hydrogencarbonate and di-hydrogenphosphate, almost identical buffer attributes as whole human resting saliva. It was further demonstrated that changes in the protein concentration as small as 0.1% may change the buffer value of a buffer solution up to 15 times. Additionally, it was shown that there was a protein concentration change in the same range (0.16% between saliva samples collected at the time periods of 13:00 and others collected at 9:00 am and 17:00. The mode of the protein expression changed between these samples corresponded to the change in basic buffer power and the change of the buffer value at pH 6.7. Finally, SDS Page and Ruthenium II tris (bathophenantroline disulfonate staining unveiled a constant protein expression in all samples except for one 50 kDa protein band. As the change in the expression pattern of that 50 kDa protein band corresponded to the change in basic buffer power and the buffer value at pH 6.7, it was reasonable to conclude that this 50 kDa protein band may contain the protein(s belonging to the protein buffer system of human saliva.

Redox buffered hydrofluoric acid etchant for the reduction of galvanic attack during release etching of MEMS devices having noble material films

Science.gov (United States)

Hankins, Matthew G [Albuquerque, NM

2009-10-06

Etchant solutions comprising a redox buffer can be used during the release etch step to reduce damage to the structural layers of a MEMS device that has noble material films. A preferred redox buffer comprises a soluble thiophosphoric acid, ester, or salt that maintains the electrochemical potential of the etchant solution at a level that prevents oxidation of the structural material. Therefore, the redox buffer preferentially oxidizes in place of the structural material. The sacrificial redox buffer thereby protects the exposed structural layers while permitting the dissolution of sacrificial oxide layers during the release etch.

Effect of pH, buffer concentration and buffer composition on the absorption of theophylline from the small intestine of the rat

NARCIS (Netherlands)

Blaey, C.J. de; Schurgers, N.

1984-01-01

The absorption of theophylline from the small intestine of the rat was investigated using buffer solutions of different pH (3.0–9.2), composition and concentration. The technique used, encloses luminal perfusion of an intestinal loop with collection of the blood draining the perfused loop, which

Isolation and Characterization of Chinese Standard Fulvic Acid Sub-fractions Separated from Forest Soil by Stepwise Elution with Pyrophosphate Buffer

Science.gov (United States)

Bai, Yingchen; Wu, Fengchang; Xing, Baoshan; Meng, Wei; Shi, Guolan; Ma, Yan; Giesy, John P.

2015-01-01

XAD-8 adsorption technique coupled with stepwise elution using pyrophosphate buffers with initial pH values of 3, 5, 7, 9, and 13 was developed to isolate Chinese standard fulvic acid (FA) and then separated the FA into five sub-fractions: FApH3, FApH5, FApH7, FApH9 and FApH13, respectively. Mass percentages of FApH3-FApH13 decreased from 42% to 2.5%, and the recovery ratios ranged from 99.0% to 99.5%. Earlier eluting sub-fractions contained greater proportions of carboxylic groups with greater polarity and molecular mass, and later eluting sub-fractions had greater phenolic and aliphatic content. Protein-like components, as well as amorphous and crystalline poly(methylene)-containing components were enriched using neutral and basic buffers. Three main mechanisms likely affect stepwise elution of humic components from XAD-8 resin with pyrophosphate buffers including: 1) the carboxylic-rich sub-fractions are deprotonated at lower pH values and eluted earlier, while phenolic-rich sub-fractions are deprotonated at greater pH values and eluted later. 2) protein or protein-like components can be desorbed and eluted by use of stepwise elution as progressively greater pH values exceed their isoelectric points. 3) size exclusion affects elution of FA sub-fractions. Successful isolation of FA sub-fractions will benefit exploration of the origin, structure, evolution and the investigation of interactions with environmental contaminants. PMID:25735451

Heuristics for the Buffer Allocation Problem with Collision Probability Using Computer Simulation

Directory of Open Access Journals (Sweden)

Eishi Chiba

2015-01-01

Full Text Available The standard manufacturing system for Flat Panel Displays (FPDs consists of a number of pieces of equipment in series. Each piece of equipment usually has a number of buffers to prevent collision between glass substrates. However, in reality, very few of these buffers seem to be used. This means that redundant buffers exist. In order to reduce cost and space necessary for manufacturing, the number of buffers should be minimized with consideration of possible collisions. In this paper, we focus on an in-line system in which each piece of equipment can have any number of buffers. In this in-line system, we present a computer simulation method for the computation of the probability of a collision occurring. Based on this method, we try to find a buffer allocation that achieves the smallest total number of buffers under an arbitrarily specified collision probability. We also implement our proposed method and present some computational results.

Project Robust Scheduling Based on the Scattered Buffer Technology

Directory of Open Access Journals (Sweden)

Nansheng Pang

2018-04-01

Full Text Available The research object in this paper is the sub network formed by the predecessor’s affect on the solution activity. This paper is to study three types of influencing factors from the predecessors that lead to the delay of starting time of the solution activity on the longest path, and to analyze the influence degree on the delay of the solution activity’s starting time from different types of factors. On this basis, through the comprehensive analysis of various factors that influence the solution activity, this paper proposes a metric that is used to evaluate the solution robustness of the project scheduling, and this metric is taken as the optimization goal. This paper also adopts the iterative process to design a scattered buffer heuristics algorithm based on the robust scheduling of the time buffer. At the same time, the resource flow network is introduced in this algorithm, using the tabu search algorithm to solve baseline scheduling. For the generation of resource flow network in the baseline scheduling, this algorithm designs a resource allocation algorithm with the maximum use of the precedence relations. Finally, the algorithm proposed in this paper and some other algorithms in previous literature are taken into the simulation experiment; under the comparative analysis, the experimental results show that the algorithm proposed in this paper is reasonable and feasible.

Chemical solution deposited BaPbO3 buffer layers for lead zirconate titanate ferroelectric films

International Nuclear Information System (INIS)

Tseng, T.-K.; Wu, J.-M.

2005-01-01

Conductive perovskite BaPbO 3 (BPO) films have been prepared successfully by chemical solution deposition method through spin-coating on Pt/Ti/SiO 2 /Si substrates. The choice of baking temperature is a key factor on the development of conducting BPO perovskite phase. When the baking temperature is higher than 350 deg. C, the BPO films contain a high content of BaCO 3 phase after annealing at temperatures higher than 500 deg. C. If the baking temperature is chosen lower than 300 deg. C, such as 200 deg. C, the annealed BPO films consist mostly of perovskite with only traces of BaCO 3 . Choosing 200 deg. C as the baking temperature, the BPO films developed single perovskite phase at temperatures as low as 550 deg. C. The perovskite BPO phase is stable in the range of 550-650 deg. C and the measured sheet resistance of the BPO films is about 2-3 Ω/square. The perovskite BPO film as a buffer layer provides improvement in electric properties of lead zirconate titanate films

Salt-specific effects in lysozyme solutions

Directory of Open Access Journals (Sweden)

T. Janc

2016-03-01

Full Text Available The effects of additions of low-molecular-mass salts on the properties of aqueous lysozyme solutions are examined by using the cloud-point temperature, T_{cloud}, measurements. Mixtures of protein, buffer, and simple salt in water are studied at pH=6.8 (phosphate buffer and pH=4.6 (acetate buffer. We show that an addition of buffer in the amount above I_{buffer} = 0.6 mol dm^{-3} does not affect the T_{cloud} values. However, by replacing a certain amount of the buffer electrolyte by another salt, keeping the total ionic strength constant, we can significantly change the cloud-point temperature. All the salts de-stabilize the solution and the magnitude of the effect depends on the nature of the salt. Experimental results are analyzed within the framework of the one-component model, which treats the protein-protein interaction as highly directional and of short-range. We use this approach to predict the second virial coefficients, and liquid-liquid phase diagrams under conditions, where T_{cloud} is determined experimentally.

Using fractional order method to generalize strengthening generating operator buffer operator and weakening buffer operator

OpenAIRE

Wu, L.; Liu, S.; Yang, Yingjie

2016-01-01

Traditional integer order buffer operator is extended to fractional order buffer operator, the corresponding relationship between the weakening buffer operator and the strengthening buffer operator is revealed. Fractional order buffer operator not only can generalize the weakening buffer operator and the strengthening buffer operator, but also realize tiny adjustment of buffer effect. The effectiveness of GM(1,1) with the fractional order buffer operator is validated by six cases.

Investigations into the stabilization of drugs by sugar glasses : III. The influence of various high-pH buffers

NARCIS (Netherlands)

Eriksson, Jonas H C; Hinrichs, Wouter L J; de Jong, Gerhardus J; Somsen, Govert W; Frijlink, Henderik W

PURPOSE: To study the effect of the high-pH buffers ammediol, borax, CHES, TRIS, and Tricine on the glass transition temperature of the freeze concentrated fraction (Tg') of trehalose/buffer and inulin/buffer solutions at pH 6.0 and pH 9.8. Also, the glass transition temperature (Tg) of sugar

Effect of buffer and antioxidant on stability of a mercaptopurine suspension.

Science.gov (United States)

Aliabadi, Hamidreza Montazeri; Romanick, Marcel; Desai, Sunil; Lavasanifar, Afsaneh

2008-03-01

The stability of standard and modified mercaptopurine suspensions when stored at room temperature and under refrigerated conditions to test the feasibility of increasing shelf life was studied. A 50-mg/mL mercaptopurine suspension was compounded by adding simple syrup, cherry syrup, and sterile water for irrigation to triturated mercaptopurine tablets for the initial reference formulation. Three additional formulations were prepared by adding an antioxidant (ascorbic acid 10 mg), a buffer (sodium phosphate monobasic monohydrate 500 mg), and a combination of antioxidant and buffer to the reference formulation. Each compounded batch was divided into two parts and stored in amber bottles at room temperature (19-23 degrees C) or under refrigerated conditions (4-8 degrees C). Analysis through high-performance liquid chromatography determined mercaptopurine levels after three and seven days and weekly thereafter for at least two weeks after shelf life was reached under specified storage conditions. Solutions with at least 93% of the original mercaptopurine concentration and with no observable sign of aggregation or cake formation were considered stable. The reference suspension of mercaptopurine showed an acceptable physical and chemical stability of up to 5 weeks when stored at room temperature. The addition of ascorbic acid extended the shelf life of the compounded suspension to 11 weeks. However, the addition of sodium phosphate monobasic did not improve the stability of mercaptopurine in the suspension. The results showed a higher stability for all formulations after storage at room temperature compared with those stored in a refrigerator. A standard oral suspension of mercaptopurine contained an acceptable drug concentration for up to 5 weeks when stored at room temperature. The addition of ascorbic acid at a concentration of 0.1% w/v to the standard formulation increased the suspension's shelf life at room temperature to 11 weeks.

Influence of temperature, chloride ions and chromium element on the electronic property of passive film formed on carbon steel in bicarbonate/carbonate buffer solution

Energy Technology Data Exchange (ETDEWEB)

Li, D.G. [School of Materials Science and Engineering, Xi' an Jiaotong University, Xi' an 710049 (China); Tubular Goods Research Center of CNPC, Xi' an 710065 (China)], E-mail: dangguoli78@yahoo.com.cn; Feng, Y.R.; Bai, Z.Q. [Tubular Goods Research Center of CNPC, Xi' an 710065 (China); Zhu, J.W.; Zheng, M.S. [School of Materials Science and Engineering, Xi' an Jiaotong University, Xi' an 710049 (China)

2007-11-01

The influences of temperature, chloride ions and chromium element on the electronic property of passive film formed on carbon steel in NaHCO{sub 3}/Na{sub 2}CO{sub 3} buffer solution are investigated by capacitance measurement and electrochemical impedance spectroscopy (EIS). The results show that the passive film appears n-type semiconductive character; with increasing the solution temperature, the addition of chromium into carbon steel and increasing the concentration of chloride ions, the slopes of Mott-Schottky plots decrease, which indicates the increment of the defect density in the passive film. EIS results show that the transfer impedance R{sub 1} and the diffusion impedance W decrease with increasing the solution temperature, with the addition of chromium into carbon steel and with increasing the chloride ions concentration. It can be concluded that the corrosion protection effect of passive film on the substrate decreases with increasing the solution temperature, adding chromium into carbon steel and increasing chloride ions concentration.

Cube textured CeO2, BaZrO3 and LaAlO3 buffer layers on Ni based Substrates

International Nuclear Information System (INIS)

Deinhofer, C; Gritzner, G

2006-01-01

CeO 2 , BaZrO 3 as well as LaAlO 3 buffer layers were deposited on {100} Ni + 5 weight-% W substrates by a wet chemical technique. The solutions were prepared by dissolving the metal nitrates or acetates and zirconiumacetylacetonate, respectively, in mixtures of acetic acid, methanol and water. The solutions were applied by dip- or spincoating, dried at 135 deg. C and annealed at temperatures between 900 and 1 400 deg. C depending on the buffer layer for 15 min. under Ar-5% H 2 gas flow. Pole-figure measurements proved the exact texture of each buffer layer. Electron microscopy showed dense and smooth buffer layers

Gossip-based solutions for discrete rendezvous in populations of communicating agents.

Science.gov (United States)

Hollander, Christopher D; Wu, Annie S

2014-01-01

The objective of the rendezvous problem is to construct a method that enables a population of agents to agree on a spatial (and possibly temporal) meeting location. We introduce the buffered gossip algorithm as a general solution to the rendezvous problem in a discrete domain with direct communication between decentralized agents. We compare the performance of the buffered gossip algorithm against the well known uniform gossip algorithm. We believe that a buffered solution is preferable to an unbuffered solution, such as the uniform gossip algorithm, because the use of a buffer allows an agent to use multiple information sources when determining its desired rendezvous point, and that access to multiple information sources may improve agent decision making by reinforcing or contradicting an initial choice. To show that the buffered gossip algorithm is an actual solution for the rendezvous problem, we construct a theoretical proof of convergence and derive the conditions under which the buffered gossip algorithm is guaranteed to produce a consensus on rendezvous location. We use these results to verify that the uniform gossip algorithm also solves the rendezvous problem. We then use a multi-agent simulation to conduct a series of simulation experiments to compare the performance between the buffered and uniform gossip algorithms. Our results suggest that the buffered gossip algorithm can solve the rendezvous problem faster than the uniform gossip algorithm; however, the relative performance between these two solutions depends on the specific constraints of the problem and the parameters of the buffered gossip algorithm.

Gossip-based solutions for discrete rendezvous in populations of communicating agents.

Directory of Open Access Journals (Sweden)

Christopher D Hollander

Full Text Available The objective of the rendezvous problem is to construct a method that enables a population of agents to agree on a spatial (and possibly temporal meeting location. We introduce the buffered gossip algorithm as a general solution to the rendezvous problem in a discrete domain with direct communication between decentralized agents. We compare the performance of the buffered gossip algorithm against the well known uniform gossip algorithm. We believe that a buffered solution is preferable to an unbuffered solution, such as the uniform gossip algorithm, because the use of a buffer allows an agent to use multiple information sources when determining its desired rendezvous point, and that access to multiple information sources may improve agent decision making by reinforcing or contradicting an initial choice. To show that the buffered gossip algorithm is an actual solution for the rendezvous problem, we construct a theoretical proof of convergence and derive the conditions under which the buffered gossip algorithm is guaranteed to produce a consensus on rendezvous location. We use these results to verify that the uniform gossip algorithm also solves the rendezvous problem. We then use a multi-agent simulation to conduct a series of simulation experiments to compare the performance between the buffered and uniform gossip algorithms. Our results suggest that the buffered gossip algorithm can solve the rendezvous problem faster than the uniform gossip algorithm; however, the relative performance between these two solutions depends on the specific constraints of the problem and the parameters of the buffered gossip algorithm.

Study of buffer substrate and Arenga wood fiber size on hydroponic Kailan (Brassica alboglabra)

Science.gov (United States)

Harjoko, D.; Anggraheny, M. D.; Arniputri, R. B.

2018-03-01

Kailan is a kind of vegetable that has high economic value, however its prospect is not well developed. One of obstacles in Kailan cultivation is the limitation of fertile soil, that can be solved by using hydroponic substrate. Considering its amount and potential, the fiber waste of Arenga wood was selected as substrate candidate. For that, this research aims to study the growth and yield of Kailan with different soaking treatment using buffer solution and size of Arenga wood fiber in the hydroponic substrate. Research was conducted at Green House Laboratory, Faculty of Agriculture Sebelas Maret University Surakarta from February to May 2017. The treatments were soaking buffer solution with EC 1.2 mScm-1; 1.4 mScm-1; and 1.6 mScm-1 and the size of Arenga fiber <1 cm, 1-2 cm and 2-3 cm. In this experiment, sand media was used as control. Result show that, soaking in 1.6 mScm-1 EC buffer solution with Arenga fiber size lower than 3 cm gives higher root volume compared to other treatments combination.

Evaluation of sonication treatment and buffer composition on rumen bacteria protein extraction and carboxymethylcellulase activity.

Science.gov (United States)

Prauchner, Carlos A; Kozloski, Gilberto V; Farenzena, Roberta

2013-05-01

The methodological procedures for studying the fibrolytic activity of rumen bacteria are not clearly established. In this study the efficiency of sonication treatment and buffer composition (i.e. buffer varying in tonicity or pH) on the level of protein extraction from the residue of forage samples incubated in the rumen of a grazing steer and the effect of buffer composition or CaCl₂ concentration on the carboxymethylcellulase (CMCase) activity of the released protein were evaluated. The amount of protein released from the residue of incubation was higher (P buffer pH (P buffer. Both linear and quadratic effects (P buffer pH on CMCase activity were significant, with CMCase activity being maximal at pH 5.4-6.1. CMCase activity was higher (P buffer solution that includes a calcium source. When pH is not a treatment factor, the buffer pH should be between 5.5 and 6. © 2012 Society of Chemical Industry.

Buffered Electrochemical Polishing of Niobium

Energy Technology Data Exchange (ETDEWEB)

Ciovati, Gianluigi [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Tian, Hui [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); College of William and Mary, Williamsburg, VA (United States); Corcoran, Sean [Virginia Polytechnic Inst. and State Univ. (Virginia Tech), Blacksburg, VA (United States)

2011-03-01

The standard preparation of superconducting radio-frequency (SRF) cavities made of pure niobium include the removal of a 'damaged' surface layer, by buffered chemical polishing (BCP) or electropolishing (EP), after the cavities are formed. The performance of the cavities is characterized by a sharp degradation of the quality factor when the surface magnetic field exceeds about 90 mT, a phenomenon referred to as 'Q-drop.' In cavities made of polycrystalline fine grain (ASTM 5) niobium, the Q-drop can be significantly reduced by a low-temperature (? 120 °C) 'in-situ' baking of the cavity if the chemical treatment was EP rather than BCP. As part of the effort to understand this phenomenon, we investigated the effect of introducing a polarization potential during buffered chemical polishing, creating a process which is between the standard BCP and EP. While preliminary results on the application of this process to Nb cavities have been previously reported, in this contribution we focus on the characterization of this novel electrochemical process by measuring polarization curves, etching rates, surface finish, electrochemical impedance and the effects of temperature and electrolyte composition. In particular, it is shown that the anodic potential of Nb during BCP reduces the etching rate and improves the surface finish.

Development of a four-zone carousel process packed with metal ion-imprinted polymer for continuous separation of copper ions from manganese ions, cobalt ions, and the constituent metal ions of the buffer solution used as eluent.

Science.gov (United States)

Jo, Se-Hee; Park, Chanhun; Yi, Sung Chul; Kim, Dukjoon; Mun, Sungyong

2011-08-19

A three-zone carousel process, in which Cu(II)-imprinted polymer (Cu-MIP) and a buffer solution were employed as adsorbent and eluent respectively, has been developed previously for continuous separation of Cu²⁺ (product) from Mn²⁺ and Co²⁺ (impurities). Although this process was reported to be successful in the aforementioned separation task, the way of using a buffer solution as eluent made it inevitable that the product stream included the buffer-related metal ions (i.e., the constituent metal ions of the buffer solution) as well as copper ions. For a more perfect recovery of copper ions, it would be necessary to improve the previous carousel process such that it can remove the buffer-related metal ions from copper ions while maintaining the previous function of separating copper ions from the other 2 impure heavy-metal ions. This improvement was made in this study by proposing a four-zone carousel process based on the following strategy: (1) the addition of one more zone for performing the two-step re-equilibration tasks and (2) the use of water as the eluent of the washing step in the separation zone. The operating conditions of such a proposed process were determined on the basis of the data from a series of single-column experiments. Under the determined operating conditions, 3 runs of carousel experiments were carried out. The results of these experiments revealed that the feed-loading time was a key parameter affecting the performance of the proposed process. Consequently, the continuous separation of copper ions from both the impure heavy-metal ions and the buffer-related metal ions could be achieved with a purity of 91.9% and a yield of 92.8% by using the proposed carousel process based on a properly chosen feed-loading time. Copyright © 2011 Elsevier B.V. All rights reserved.

A buffer material optimal design in the radioactive wastes geological disposal using the satisficing trade-off method and the self-organizing map

International Nuclear Information System (INIS)

Okamoto, Takashi; Hanaoka, Yuya; Aiyoshi, Eitaro; Kobayashi, Yoko

2012-01-01

In this paper, we consider a multi-objective optimization method in order to obtain a preferred solution for the buffer material optimal design problem in the high-level radioactive wastes geological disposal. The buffer material optimal design problem is formulated as a constrained multi-objective optimization problem. Its Pareto optimal solutions are distributed evenly on whole bounds of the feasible region. Hence, we develop a search method to find a preferred solution easily for a decision maker from the Pareto optimal solutions which are distributed evenly and vastly. In the preferred solution search method, the visualization technique of a Pareto optimal solution set using the self-organizing map is introduced into the satisficing trade-off method which is the interactive method to obtain a Pareto optimal solution that satisfies a decision maker. We confirm the effectiveness of the preferred solution search method in the buffer material optimal design problem. (author)

Electrochemical Behavior Assessment of As-Cast Mg-Y-RE-Zr Alloy in Phosphate Buffer Solutions (X Na3PO4 + Y Na2HPO4) Using Electrochemical Impedance Spectroscopy and Mott-Schottky Techniques

Science.gov (United States)

Fattah-alhosseini, Arash; Asgari, Hamed

2018-05-01

In the present study, electrochemical behavior of as-cast Mg-Y-RE-Zr alloy (RE: rare-earth alloying elements) was investigated using electrochemical tests in phosphate buffer solutions (X Na3PO4 + Y Na2HPO4). X-ray diffraction techniques and Scanning electron microscopy equipped with energy dispersive x-ray spectroscopy were used to investigate the microstructure and phases of the experimental alloy. Different electrochemical tests such as potentiodynamic polarization (PDP), electrochemical impedance spectroscopy (EIS) and Mott-Schottky (M-S) analysis were carried out in order to study the electrochemical behavior of the experimental alloy in phosphate buffer solutions. The PDP curves and EIS measurements indicated that the passive behavior of the as-cast Mg-Y-RE-Zr alloy in phosphate buffer solutions was weakened by an increase in the pH, which is related to formation of an imperfect and less protective passive layer on the alloy surface. The presence of the insoluble zirconium particles along with high number of intermetallic phases of RE elements mainly Mg24Y5 in the magnesium matrix can deteriorate the corrosion performance of the alloy by disrupting the protective passive layer that is formed at pH values over 11. These insoluble zirconium particles embedded in the matrix can detrimentally influence the passivation. The M-S analysis revealed that the formed passive layers on Mg-Y-RE-Zr alloy behaved as an n-type semiconductor. An increase in donor concentration accompanying solutions of higher alkalinity is thought to result in the formation of a less resistive passive layer.

Massive bosons interacting with gravity: No standard solutions in Robertson-Walker space-time

International Nuclear Information System (INIS)

Zecca, A.

2009-01-01

The problem of the interaction of boson and gravitational field is formulated in the Robertson-Walker space-time. It consist the simultaneous solution of the boson and of the Einstein field equation whose source is the energy momentum tensor of the boson field. By direct verification it is shown that the problem does not admit solutions in the class of massive standard solutions, previously determined, of the boson field equation. Also there cannot be solutions, in case of massive interacting boson, that are superpositions of standard solutions. The case of massless boson field is left open. The result is essentially due to the very special form of the Einstein tensor in Robertson-Walker metric.

Thermo-hydro-mechanical tests of buffer material

International Nuclear Information System (INIS)

Pintado, X.; Hassan, Md. M.; Martikainen, J.

2013-10-01

MX-80 bentonite is the reference clay material for the buffer component planned to be used in the deep geological repository for the disposal of spent nuclear fuel in Finland. The buffer presents complex thermo-hydro-mechanical behavior which is modeled with different constitutive models for heat flow, water flow and stress-strain evolution in the buffer. Thermo, hydro and mechanical models need parameters to evaluate the THM-behavior. These modeling parameters were determined by performing series of laboratory experiments as follows: Water retention curve tests were performed on compacted bentonite samples, encompassing a range of initial dry density values from 1397 to 1718 kg/m 3 as the initial water content was around of 5-8 %. The water retention curve was determined by imposing different suctions to the samples and the suctions were then checked using capacitive hygrometer and chilled mirror psychrometer. Oedometer tests were performed on compacted bentonite samples, encompassing a range of initial dry density values from 1590 to 1750 kg/m 3 as the initial water content was around of 6 %. Samples were saturated with tap water, 35 or 70 g/L salt solutions. Infiltration tests were performed on compacted unsaturated bentonite samples, encompassing a range of initial dry density values from 1400 to 1720 kg/m 3 as the initial water content was approximately between 4-7 %. Samples were saturated with tap water, 0.87, 35 or 70 g/L salt solutions. Tortuosity tests were performed on bentonite samples, encompassing a range of dry density values from 1460 to 1750 kg/m 3 and the degree of saturation varied between 33-93 %. Thermal conductivity tests were performed on compacted bentonite samples, encompassing a range of dry density values from 1545 to 1715 kg/m 3 and the degree of saturation varied between 31-88 %. The measurement was performed using a thermal needle probe. The general trend of all analyzed parameters was as expected when dry density, water content, and

Thermo-hydro-mechanical tests of buffer material

Energy Technology Data Exchange (ETDEWEB)

Pintado, X.; Hassan, Md. M.; Martikainen, J. [B and Tech Oy, Helsinki (Finland)

2013-10-15

MX-80 bentonite is the reference clay material for the buffer component planned to be used in the deep geological repository for the disposal of spent nuclear fuel in Finland. The buffer presents complex thermo-hydro-mechanical behavior which is modeled with different constitutive models for heat flow, water flow and stress-strain evolution in the buffer. Thermo, hydro and mechanical models need parameters to evaluate the THM-behavior. These modeling parameters were determined by performing series of laboratory experiments as follows: Water retention curve tests were performed on compacted bentonite samples, encompassing a range of initial dry density values from 1397 to 1718 kg/m{sup 3} as the initial water content was around of 5-8 %. The water retention curve was determined by imposing different suctions to the samples and the suctions were then checked using capacitive hygrometer and chilled mirror psychrometer. Oedometer tests were performed on compacted bentonite samples, encompassing a range of initial dry density values from 1590 to 1750 kg/m{sup 3} as the initial water content was around of 6 %. Samples were saturated with tap water, 35 or 70 g/L salt solutions. Infiltration tests were performed on compacted unsaturated bentonite samples, encompassing a range of initial dry density values from 1400 to 1720 kg/m{sup 3} as the initial water content was approximately between 4-7 %. Samples were saturated with tap water, 0.87, 35 or 70 g/L salt solutions. Tortuosity tests were performed on bentonite samples, encompassing a range of dry density values from 1460 to 1750 kg/m{sup 3} and the degree of saturation varied between 33-93 %. Thermal conductivity tests were performed on compacted bentonite samples, encompassing a range of dry density values from 1545 to 1715 kg/m{sup 3} and the degree of saturation varied between 31-88 %. The measurement was performed using a thermal needle probe. The general trend of all analyzed parameters was as expected when dry

Internal acid buffering in San Joaquin Valley fog drops and its influence on aerosol processing

Science.gov (United States)

Collett, Jeffrey L.; Hoag, Katherine J.; Rao, Xin; Pandis, Spyros N.

Although several chemical pathways exist for S(IV) oxidation in fogs and clouds, many are self-limiting: as sulfuric acid is produced and the drop pH declines, the rates of these pathways also decline. Some of the acid that is produced can be buffered by uptake of gaseous ammonia. Additional internal buffering can result from protonation of weak and strong bases present in solution. Acid titrations of high pH fog samples (median pH=6.49) collected in California's San Joaquin Valley reveal the presence of considerable internal acid buffering. In samples collected at a rural location, the observed internal buffering could be nearly accounted for based on concentrations of ammonia and bicarbonate present in solution. In samples collected in the cities of Fresno and Bakersfield, however, significant additional, unexplained buffering was present over a pH range extending from approximately four to seven. The additional buffering was found to be associated with dissolved compounds in the fogwater. It could not be accounted for by measured concentrations of low molecular weight ( C1- C3) carboxylic acids, S(IV), phosphate, or nitrophenols. The amount of unexplained buffering in individual fog samples was found to correlate strongly with the sum of sample acetate and formate concentrations, suggesting that unmeasured organic species may be important contributors. Simulation of a Bakersfield fog episode with and without the additional, unexplained buffering revealed a significant impact on the fog chemistry. When the additional buffering was included, the simulated fog pH remained 0.3-0.7 pH units higher and the amount of sulfate present after the fog evaporated was increased by 50%. Including the additional buffering in the model simulation did not affect fogwater nitrate concentrations and was found to slightly decrease ammonium concentrations. The magnitude of the buffering effect on aqueous sulfate production is sensitive to the amount of ozone present to oxidize S

Protein-bound solute removal during extended multipass versus standard hemodialysis

DEFF Research Database (Denmark)

Eloot, Sunny; Van Biesen, Wim; Axelsen, Mette

2015-01-01

and middle molecules compared to standard hemodialysis (SHD). Since protein-bound solutes (PBS) exert important pathophysiological effects, we investigated whether MPHD results in improved removal of PBS as well. METHODS: A cross-over study (Clinical Trial NCT01267760) was performed in nine stable HD......), hippuric acid (HA), indole acetic acid (IAA), indoxyl sulfate (IS), and p-cresylsulfate (PCS). Dialyser extraction ratio, reduction ratio, and solute removal were calculated for these solutes. RESULTS: Already at 60 min after dialysis start, the extraction ratio in the hemodialyser was a factor 1.4-4 lower...

Defining the buffering process by a triprotic acid without relying on Stewart-electroneutrality considerations.

Science.gov (United States)

Nguyen, Minhtri K; Kao, Liyo; Kurtz, Ira

2011-08-17

Upon the addition of protons to an aqueous solution, a component of the H+ load will be bound i.e. buffered. In an aqueous solution containing a triprotic acid, H+ can be bound to three different states of the acid as well as to OH- ions that are derived from the auto-ionization of H2O. In quantifying the buffering process of a triprotic acid, one must define the partitioning of H+ among the three states of the acid and also the OH- ions in solution in order to predict the equilibrium pH value. However, previous quantitative approaches that model triprotic acid titration behaviour and used to predict the equilibrium pH rely on the mathematical convenience of electroneutrality/charge balance considerations. This fact has caused confusion in the literature, and has led to the assumption that charge balance/electroneutrality is a causal factor in modulating proton buffering (Stewart formulation). However, as we have previously shown, although charge balance can be used mathematically as a convenient tool in deriving various formulae, electroneutrality per se is not a fundamental physicochemical parameter that is mechanistically involved in the underlying buffering and proton transfer reactions. The lack of distinction between a mathematical tool, and a fundamental physicochemical parameter is in part a reason for the current debate regarding the Stewart formulation of acid-base analysis. We therefore posed the following question: Is it possible to generate an equation that defines and predicts the buffering of a triprotic acid that is based only on H+ partitioning without incorporating electroneutrality in the derivation? Towards this goal, we derived our new equation utilizing: 1) partitioning of H+ buffering; 2) conservation of mass; and 3) acid-base equilibria. In validating this model, we compared the predicted equilibrium pH with the measured pH of an aqueous solution consisting of Na2HPO4 to which HCl was added. The measured pH values were in excellent agreement

Defining the buffering process by a triprotic acid without relying on stewart-electroneutrality considerations

Directory of Open Access Journals (Sweden)

Kao Liyo

2011-08-01

Full Text Available Abstract Upon the addition of protons to an aqueous solution, a component of the H+ load will be bound i.e. buffered. In an aqueous solution containing a triprotic acid, H+ can be bound to three different states of the acid as well as to OH- ions that are derived from the auto-ionization of H2O. In quantifying the buffering process of a triprotic acid, one must define the partitioning of H+ among the three states of the acid and also the OH- ions in solution in order to predict the equilibrium pH value. However, previous quantitative approaches that model triprotic acid titration behaviour and used to predict the equilibrium pH rely on the mathematical convenience of electroneutrality/charge balance considerations. This fact has caused confusion in the literature, and has led to the assumption that charge balance/electroneutrality is a causal factor in modulating proton buffering (Stewart formulation. However, as we have previously shown, although charge balance can be used mathematically as a convenient tool in deriving various formulae, electroneutrality per se is not a fundamental physicochemical parameter that is mechanistically involved in the underlying buffering and proton transfer reactions. The lack of distinction between a mathematical tool, and a fundamental physicochemical parameter is in part a reason for the current debate regarding the Stewart formulation of acid-base analysis. We therefore posed the following question: Is it possible to generate an equation that defines and predicts the buffering of a triprotic acid that is based only on H+ partitioning without incorporating electroneutrality in the derivation? Towards this goal, we derived our new equation utilizing: 1 partitioning of H+ buffering; 2 conservation of mass; and 3 acid-base equilibria. In validating this model, we compared the predicted equilibrium pH with the measured pH of an aqueous solution consisting of Na2HPO4 to which HCl was added. The measured pH values

Defining the buffering process by a triprotic acid without relying on stewart-electroneutrality considerations

Science.gov (United States)

2011-01-01

Upon the addition of protons to an aqueous solution, a component of the H+ load will be bound i.e. buffered. In an aqueous solution containing a triprotic acid, H+ can be bound to three different states of the acid as well as to OH- ions that are derived from the auto-ionization of H2O. In quantifying the buffering process of a triprotic acid, one must define the partitioning of H+ among the three states of the acid and also the OH- ions in solution in order to predict the equilibrium pH value. However, previous quantitative approaches that model triprotic acid titration behaviour and used to predict the equilibrium pH rely on the mathematical convenience of electroneutrality/charge balance considerations. This fact has caused confusion in the literature, and has led to the assumption that charge balance/electroneutrality is a causal factor in modulating proton buffering (Stewart formulation). However, as we have previously shown, although charge balance can be used mathematically as a convenient tool in deriving various formulae, electroneutrality per se is not a fundamental physicochemical parameter that is mechanistically involved in the underlying buffering and proton transfer reactions. The lack of distinction between a mathematical tool, and a fundamental physicochemical parameter is in part a reason for the current debate regarding the Stewart formulation of acid-base analysis. We therefore posed the following question: Is it possible to generate an equation that defines and predicts the buffering of a triprotic acid that is based only on H+ partitioning without incorporating electroneutrality in the derivation? Towards this goal, we derived our new equation utilizing: 1) partitioning of H+ buffering; 2) conservation of mass; and 3) acid-base equilibria. In validating this model, we compared the predicted equilibrium pH with the measured pH of an aqueous solution consisting of Na2HPO4 to which HCl was added. The measured pH values were in excellent agreement

A THEORETICAL DISCUSSION OF THE ECONOMIC EFFECTS OF BUFFER STOCKS AND BUFFER FUNDS

OpenAIRE

Simmons, Phil

1988-01-01

It has been established that the absence of risk markets justifies market intervention in principle. The form of intervention that has been discussed most widely in the literature is the buffer stock. This paper points out that other forms of intervention, specifically buffer funds, are likely to perform better. The analysis shows that buffer funds are likely to outperform buffer stocks because they address market failure more directly. A sub-theme developed in this paper is that since buffer...

Role of the buffer solution in the chemical deposition of CdS films for CIGS solar cell applications

Energy Technology Data Exchange (ETDEWEB)

Lee, Sooho; Kim, Donguk; Baek, Dohyun; Hong, Byoungyou; Yi, Junsin; Lee, Jaehyeong [Sungkyunkwan University, Suwon (Korea, Republic of); Park, Yongseob [Chosun College of Science and and Technology, Gwangju (Korea, Republic of); Choi, Wonseok [Hanbat National University, Daejeon (Korea, Republic of)

2014-05-15

In this work, the effects of NH{sub 4}Ac on the structural and the electro-optical properties of CdS films were investigated. CdS thin films were deposited on soda-lime glass and indium-tin-oxide (ITO) coated glass from a chemical bath containing 0.025 M cadmium acetate, 0 M ∼ 0.2 M ammonium acetate, 0.5 M thiourea, and ammonia. Cadmium acetate was the cadmium source, ammonium acetate served as a buffer, ammonia was the complexing agent, and thiourea was the source of sulfur. A commonly- available chemical bath deposition system was successfully modified to obtain precise control over the pH of the solution at 75 .deg. C during the deposition. Chemically deposited CdS films were studied by using field-emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), optical transmittance, and electrical resistivity measurements.

Extraction-spectrophotometric study of ruthenium (4) and osmium (4,8) reaction with 2-mercaptobenzimidazole, 2-mercaptobenzoxazole and 2-mercaptobenzothiazole in acetate buffer solutions

Energy Technology Data Exchange (ETDEWEB)

Lomakina, L N; Ignat' eva, T I; Busev, A I [Moskovskij Gosudarstvennyj Univ. (USSR)

1978-03-01

The complex formation of Ru(4) and Os(4, 8) with 2-mercaptobenzimidazole (MBI), 2-mercaptobenzoxazole (MBO) and 2-mercaptobenzothiazole (MBT) has been studied spectrophotometrically in acetate buffer solutions. As it has been shown earlier, Os and Ru react with the reagents in the oxidation state of three . Compound polinuclear structures of Ru and Os with MBI and MBO are suggested. A spectrophotometric procedure has been developed of determining Ru and Os (>=10/sup -4/%) with MBO in natural and industrial materials after selective absorption of the tetraoxides during distillation.

Effects of Reusing Gel Electrophoresis and Electrotransfer Buffers on Western Blotting.

Science.gov (United States)

Heda, Ghanshyam D; Omotola, Oluwabukola B; Heda, Rajiv P; Avery, Jamie

2016-09-01

SDS-PAGE and Western blotting are 2 of the most commonly used biochemical methods for protein analysis. Proteins are electrophoretically separated based on their MWs by SDS-PAGE and then electrotransferred to a solid membrane surface for subsequent protein-specific analysis by immunoblotting, a procedure commonly known as Western blotting. Both of these procedures use a salt-based buffer, with the latter procedure consisting of methanol as an additive known for its toxicity. Previous reports present a contradictory view in favor or against reusing electrotransfer buffer, also known as Towbin's transfer buffer (TTB), with an aim to reduce the toxic waste. In this report, we present a detailed analysis of not only reusing TTB but also gel electrophoresis buffer (EB) on proteins of low to high MW range. Our results suggest that EB can be reused for at least 5 times without compromising the electrophoretic separation of mixture of proteins in an MW standard, BSA, and crude cell lysates. Additionally, reuse of EB did not affect the quality of subsequent Western blots. Successive reuse of TTB, on the other hand, diminished the signal of proteins of different MWs in a protein standard and a high MW membrane protein cystic fibrosis transmembrane-conductance regulator (CFTR) in Western blotting.

COMBINATIONS OF BUFFER-STOCKS AND BUFFER-FUNDS FOR WOOL PRICE STABILISATION IN AUSTRALIA

OpenAIRE

Moir, Brian; Piggott, Roley R.

1991-01-01

In this paper a preliminary analysis is presented of a combined buffer-fund and buffer-stock as an alternative to a pure buffer-fund or a pure buffer stock for stabilising wool prices. The alternatives analysed are designed so that each provides the same prices to producers as did the Reserve Price Scheme over the period of analysis. Least-cost combinations of policy instruments are derived. The results show that there is considerable potential for cost savings to be made by combining buffer-...

pH Sensing Properties of Flexible, Bias-Free Graphene Microelectrodes in Complex Fluids: From Phosphate Buffer Solution to Human Serum.

Science.gov (United States)

Ping, Jinglei; Blum, Jacquelyn E; Vishnubhotla, Ramya; Vrudhula, Amey; Naylor, Carl H; Gao, Zhaoli; Saven, Jeffery G; Johnson, Alan T Charlie

2017-08-01

Advances in techniques for monitoring pH in complex fluids can have a significant impact on analytical and biomedical applications. This study develops flexible graphene microelectrodes (GEs) for rapid (pH of complex biofluids by measuring real-time Faradaic charge transfer between the GE and a solution at zero electrical bias. For an idealized sample of phosphate buffer solution (PBS), the Faradaic current is varied monotonically and systematically with the pH, with a resolution of ≈0.2 pH unit. The current-pH dependence is well described by a hybrid analytical-computational model, where the electric double layer derives from an intrinsic, pH-independent (positive) charge associated with the graphene-water interface and ionizable (negative) charged groups. For ferritin solution, the relative Faradaic current, defined as the difference between the measured current response and a baseline response due to PBS, shows a strong signal associated with ferritin disassembly and the release of ferric ions at pH ≈2.0. For samples of human serum, the Faradaic current shows a reproducible rapid (pH. By combining the Faradaic current and real-time current variation, the methodology is potentially suitable for use to detect tumor-induced changes in extracellular pH. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Potential role of phosphate buffering capacity of soils in fertilizer management strategies fitted to environmental goals

NARCIS (Netherlands)

Ehlert, P.A.I.; Morel, C.; Fotyma, M.; Destain, J.P.

2003-01-01

Sorption behavior and buffering of phosphorus (P) are important, both from an agricultural and an environmental point of view. The objectives of this study were to investigate: (1) the kinetics of the transfer of P from soil to soil solution and assessing P buffering capacity of soils (PBC), as a

Organellar Calcium Buffers

Science.gov (United States)

Prins, Daniel; Michalak, Marek

2011-01-01

Ca2+ is an important intracellular messenger affecting many diverse processes. In eukaryotic cells, Ca2+ storage is achieved within specific intracellular organelles, especially the endoplasmic/sarcoplasmic reticulum, in which Ca2+ is buffered by specific proteins known as Ca2+ buffers. Ca2+ buffers are a diverse group of proteins, varying in their affinities and capacities for Ca2+, but they typically also carry out other functions within the cell. The wide range of organelles containing Ca2+ and the evidence supporting cross-talk between these organelles suggest the existence of a dynamic network of organellar Ca2+ signaling, mediated by a variety of organellar Ca2+ buffers. PMID:21421925

Glassy carbon electrode modified by conductive polyaniline coating for determination of trace lead and cadmium ions in acetate buffer solution

International Nuclear Information System (INIS)

Wang Zhaomeng; Liu Erjia; Zhao Xing

2011-01-01

Polyaniline (PANI) coatings were electrodeposited on the surfaces of glassy carbon electrodes (GCEs) to form new electrodes, i.e. PANI/GCEs. It was found that with increased deposition time, the PANI coatings became more compact while the charge transfer resistance of the coatings became higher. The PANI/GCEs were used to detect Cd 2+ and Pb 2+ ions contained in 0.1 M acetate buffer solutions using square wave anodic stripping voltammetry (SWASV). It was found that the PANI/GCE had a highest anodic stripping peak current in a solution of pH 5.3. The study of the cleaning performance of the PANI/GCEs indicated that there were less remaining metals on the surfaces of the PANI/GCEs compared to the bare GCEs after cleaning at a potential of 0.4 V, which was probably due to that the PANI coatings could effectively prevent the deposition of the metals into the surface defects of the GCEs. The PANI coatings could also reduce the passivation effect of the GCEs, thus improving the repeatability of the electrodes.

Concept cartoons for diagnosing student’s misconceptions in the topic of buffers

Science.gov (United States)

Kusumaningrum, I. A.; Ashadi; Indriyanti, N. Y.

2018-05-01

Student’s misconceptions have been concerned over twenty years in the chemistry education research. It influences students to learn new knowledge and gain a correct concept. The buffer solution is found as a difficult topic due to student’s misconception. However, the research related this subject are still rare. Concept cartoon has been used as one of the effective tools to diagnose misconceptions. This study aims to identify the effectiveness of concept cartoon to diagnose them. The concept cartoon consists of three concept questions. 98 students of grade 11 as respondents of this research and followed by interview for selected students. The data obtain of the study are analyzed by using a scoring key. The detected misconceptions are about what buffers do, what buffers are, and how buffers are able to do what they do. Concept cartoon is potential as a basic tool for remedial teaching.

Reference value standards and primary standards for pH measurements in D2O and aqueous-organic solvent mixtures: new accessions and assessments

International Nuclear Information System (INIS)

Mussini, P.R.; Mussini, T.; Rondinini, S.

1997-01-01

Recommended Reference Value Standards based on the potassium hydro-genphthalate buffer at various temperatures are reported for pH measurements in various binary solvent mixtures of water with eight organic solvents: methanol, ethanol, 2-propanol, 1,2-ethanediol, 2-methoxyethanol (''methylcellosolve''), acetonitrile, 1,4-dioxane, and dimethyl sulfoxide, together with Reference Value Standard based on the potassium deuterium phthalate buffer for pD measurements in D 2 O. In addition are reported Primary Standards for pH based on numerous buffers in various binary solvent mixtures of water with methanol, ethanol, and dimethyl sulfoxide, together with Primary Standards for pD in D 2 O based on the citrate, phosphate and carbonate buffers. (author)

Fatigue of graphite/epoxy buffer strip panels with center cracks

Science.gov (United States)

Bigelow, C. A.

1985-01-01

The effects of fatigue loading on the behavior of graphite/epoxy panels with either S-Glass or Kevlar-49 buffer strips is studied. Buffer strip panels are fatigued and tested in tension to measure their residual strength with crack-like damage. Panels are made with 45/0/-45/90 sub 2s layup with either S-Glass or Kevlar-49 buffer strip material. The buffer strips are parallel to the loading direction and made by replacing narrow strips of the 0-degree graphite plies with strips of either 0-degree S-Glass/epoxy or Kevlar-49/epoxy on a one-for-one basis. The panels are subjected to a fatigue loading spectrum MINITWIST, the shortened version of the standardized load program for the wing lower surface of a transport aircraft. Two levels of maximum strain are used in the spectrum with three durations of the fatigue spectrum. One group of panels is preloaded prior to the application of the fatigue cycling. The preload consists of statistically loading the spectrum in tension until the crack-tip damage zone reaches the ajacent buffer strips. After fatigue loading, all specimens are statistically loaded in tension to failure to determine their residual strengths.

Optimization of a model of red blood cells for the study of anti-oxidant drugs, in terms of concentration of oxidant and phosphate buffer.

Science.gov (United States)

Bureau, A; Lahet, J-J; Lenfant, F; Bouyer, F; Petitjean, M; Chaillot, B; Freysz, M

2005-08-01

The aggression of erythrocytes by an oxidative stress induces hemolysis. This paper aims to valid a model of erythrocytes in terms of composition of the phosphate buffer solution and of concentration of a well-known oxidant, AAPH. Three compositions of phosphate buffer solution are mixed with three concentrations of oxidant. The influence of these two parameters on hemolysis is independently studied by a variance analysis and a Kruskal-Wallis test when ANOVA is not available. The hemolysis rate increases with time at fixed oxidant concentration, but is not influenced by the composition of the buffer solution. The highest hemolysis rate, 90%, was only measured within 2 h with the highest oxidant concentration. If we retain this concentration of oxidant, the lower concentration of the buffer can by eliminated by a significant less hemolysis and the highest concentration of the buffer can by chosen in regard of the better precision for a similar hemolysis compared to the mean buffer. We hope to study the effect of anti-oxidant agent with such a model of erythrocytes.

Mixed RIA standard

International Nuclear Information System (INIS)

Talan, P.; Mucha, J.; Krizan, J.

1986-01-01

For the radioimmunoassay of digoxin, 3,5,3'-triiodothyronine, 17β-estradiol, progesterone, testosterone and α 1 -fetoprotein a mixed standard was prepared of these substances in a gamma globulin solution at a concentration of 0.8 to 1.4 wt.% in an aqueous buffer at pH within the range of 6 - 9. The standard contains digoxin at a concentration of 10 -4 to 10 nmol/l, 17β-estradiol at 10 -4 to 2 nmol/l, progesteron at 10 -4 to 100 nmol/l, testosterone at 1o -4 to 21 nmol/l, and α 1 -fetoprotein at 10 -4 to 10 nmol/l with at least two of these substances having concentrations higher than 10 -3 nmol/l. Examples are given of the preparation of the mixed standard with different concentrations of the components. The use of the standard has the following advantages: it is labor saving, reduces the risk of failure in the manufacture of RIA kits, eliminates mistakes in the selection of kits for the determination of different substances and allows a more economical use of material. (E.S.)

Kinetics of an acid-base catalyzed reaction (aspartame degradation) as affected by polyol-induced changes in buffer pH and pK values.

Science.gov (United States)

Chuy, S; Bell, L N

2009-01-01

The kinetics of an acid-base catalyzed reaction, aspartame degradation, were examined as affected by the changes in pH and pK(a) values caused by adding polyols (sucrose, glycerol) to phosphate buffer. Sucrose-containing phosphate buffer solutions had a lower pH than that of phosphate buffer alone, which contributed, in part, to reduced aspartame reactivity. A kinetic model was introduced for aspartame degradation that encompassed pH and buffer salt concentrations, both of which change with a shift in the apparent pK(a) value. Aspartame degradation rate constants in sucrose-containing solutions were successfully predicted using this model when corrections (that is, lower pH, lower apparent pK(a) value, buffer dilution from the polyol) were applied. The change in buffer properties (pH, pK(a)) from adding sucrose to phosphate buffer does impact food chemical stability. These effects can be successfully incorporated into predictive kinetic models. Therefore, pH and pK(a) changes from adding polyols to buffer should be considered during food product development.

Epitaxial grown InP quantum dots on a GaAs buffer realized on GaP/Si(001) templates

Energy Technology Data Exchange (ETDEWEB)

Hartwig, Walter; Wiesner, Michael; Koroknay, Elisabeth; Paul, Matthias; Jetter, Michael; Michler, Peter [Institut fuer Halbleiteroptik und Funktionelle Grenzflaechen und Research Center SCoPE, Universitaet Stuttgart, Allmandring 3, 70569 Stuttgart (Germany)

2013-07-01

The increasing necessity of higher computational capacity and security in the information technology requires originally technical solutions, which today's standard microelectronics, as their technical limits are close, can't provide anymore. One way out offers the integration of III-V semiconductor photonics with low-dimensional structures in current CMOS technology, enabling on-chip quantum optical applications, like quantum cryptography or quantum computing. Challenges in the heteroepitaxy of III-V semiconductors and silicon are the mismatches in material properties of the both systems. Defects, like dislocations and anti-phase domains (APDs), inhibit the monolithic integration of III-V semiconductor on Si. We present the growth of a thin GaAs buffer on CMOS-compatible oriented Si(001) by metal-organic vapor-phase epitaxy. To circumvent the forming APDs in the GaAs buffer a GaP on Si template (provided by NAsP{sub III/V} GmbH) was used. The dislocation density was then reduced by integrating several layers of InAs quantum dots in the GaAs buffer to bend the threading misfit dislocations. On top of this structure we grew InP quantum dots embedded in a Al{sub x}Ga{sub 1-x}InP composition and investigated the photoluminescence properties.

Operation voltage behavior of organic light emitting diodes with polymeric buffer layers doped by weak electron acceptor

Energy Technology Data Exchange (ETDEWEB)

Jeon, Hyeon Soo; Cho, Sang Hee [Department of Information Display and Advanced Display Research Center, Kyung Hee University, Seoul 130-701 (Korea, Republic of); Seo, Jaewon; Park, Yongsup [Department of Physics, Kyung Hee University, Seoul 130-701 (Korea, Republic of); Suh, Min Chul, E-mail: mcsuh@khu.ac.kr [Department of Information Display and Advanced Display Research Center, Kyung Hee University, Seoul 130-701 (Korea, Republic of)

2013-11-01

We present polymeric buffer materials based on poly[2,7-(9,9-dioctyl-fluorene)-co-(1,4-phenylene -((4-sec-butylphenyl)imino)-1,4-phenylene)] (TFB) for highly efficient solution processed organic light emitting diodes (OLEDs). Doped TFB with 9,10-dicyanoanthracene, a weak electron acceptor results in significant improvement of current flow and driving voltage. Maximum current- and power-efficiency value of 12.6 cd/A and 18.1 lm/W are demonstrated from phosphorescent red OLEDs with this doped polymeric anode buffer system. - Highlights: • Polymeric buffer materials for organic light emitting diodes (OLEDs). • Method to control hole conductivity of polymeric buffer layer in OLED device. • Enhanced current density of buffer layers upon 9,10-dicyanoanthracene (DCA) doping. • Comparison of OLED devices having polymeric buffer layer with or without DCA. • Effect on operating voltage by doping DCA in the buffer layer.

Vehicular ad hoc networks standards, solutions, and research

CERN Document Server

Molinaro, Antonella; Scopigno, Riccardo

2015-01-01

This book presents vehicular ad-hoc networks (VANETs) from the their onset, gradually going into technical details, providing a clear understanding of both theoretical foundations and more practical investigation. The editors gathered top-ranking authors to provide comprehensiveness and timely content; the invited authors were carefully selected from a list of who’s who in the respective field of interest: there are as many from Academia as from Standardization and Industry sectors from around the world. The covered topics are organized around five Parts starting from an historical overview of vehicular communications and standardization/harmonization activities (Part I), then progressing to the theoretical foundations of VANETs and a description of the day-one standard-compliant solutions (Part II), hence going into details of vehicular networking and security (Part III) and to the tools to study VANETs, from mobility and channel models, to network simulators and field trial methodologies (Part IV), and fi...

Hydrothermal behaviors and long-term stability of bentonitic buffer material

International Nuclear Information System (INIS)

Lee, Jae Owan; Cho, Won Jin

2007-01-01

In hydrothermal reaction tests, smectite-to-illite conversion was identified using a domestic bentonite which is favorably considered as a buffer material, and its dependency on various hydrothermal conditions was investigated. The analysis results of the XRD and Si concentration indicated that the smectite-to- illite conversion was a major process of bentonite alteration under the hydrothermal conditions. The temperature, potassium concentration in solution, and pH were observed to significantly affect the smectite-to illite conversion. A model of conversion reaction rate was suggested evaluate the long-term stability of smectite composing a major constituent of bentonitic buffer. It was expected from the evaluation results that the smectite would keep its integrity for very long disposal time under a normal condition, while as it might be converted to illite by 50 percent after over 5 x 10 4 year of disposal time under a conservative condition and consequently lose its swelling capacity as a buffer material of a repository

Two-Buffer Simulation Games

Directory of Open Access Journals (Sweden)

Milka Hutagalung

2016-07-01

Full Text Available We consider simulation games played between Spoiler and Duplicator on two Büchi automata in which the choices made by Spoiler can be buffered by Duplicator in two different buffers before she executes them on her structure. Previous work on such games using a single buffer has shown that they are useful to approximate language inclusion problems. We study the decidability and complexity and show that games with two buffers can be used to approximate corresponding problems on finite transducers, i.e. the inclusion problem for rational relations over infinite words.

Temperature Buffer Test. Measurements of water content and density of the excavated buffer material

Energy Technology Data Exchange (ETDEWEB)

Johannesson, Lars-Erik [Clay Technology AB, Lund (Sweden)

2010-12-15

TBT (Temperature Buffer Test) is a joint project between SKB/ANDRA and supported by ENRESA (modeling) and DBE (instrumentation), which aims at understanding and modeling the thermo-hydromechanical behavior of buffers made of swelling clay submitted to high temperatures (over 100 deg C) during the water saturation process. The test was carried out at the - 420 m level in Aespoe HRL in a 8 meters deep and 1.76 m diameter deposition hole, with two heaters (3 m long, 0.6 m diameter), surrounded by a MX-80 bentonite buffer and a confining plug on top anchored with 9 rods. It was installed during spring 2003. The bentonite around upper heater was removed during the period October - December 2009 and the buffer around the lower heater was removed during January - Mars 2010. During dismantling of the buffer, samples were taken on which analyses were made. This report describes the work with the deteroemoeination of the water content and the density of the taken samples. Most of the samples were taken from the buffer by core drilling from the upper surface of each installed bentonite block. The cores had a diameter of about 50 mm and a maximum length equal to the original height of the bentonite blocks (about 500 mm). The water content of the buffer was determined by drying a sample at a temperature of 105 deg C for 24 h and the bulk density was determined by weighing a sample both in the air and immerged in paraffin oil with known density. The water content, dry density, degree of saturation and void ratio of the buffer were then plotted. The plots show that all parts of the buffer had taken up water and the degree of saturation of the buffer varied between 90 - 100%. Large variation in the dry density of the buffer was also observed.

Application Of The Work Breakdown Structure In Determining Cost Buffers In Construction Schedules

Directory of Open Access Journals (Sweden)

Połoński M.

2015-03-01

Full Text Available The paper presents methods of determining the location of cost buffers and corresponding contingency costs in the CPM schedule based on its work breakdown structure. Application of correctly located cost buffers with appropriately established reserve costs is justified by the common overrunning of scheduled costs in construction projects. Interpolated cost buffers (CB as separate tasks have been combined with relevant summary tasks by the start–to–start (SS relationship, whereas the time of their execution has been dynamically connected with the time of accomplishment of particular summary tasks using the “paste connection” option. Besides cost buffers linked with the group of tasks assigned to summary tasks, a definition of the cost buffer for the entire project (PCB has been proposed, i.e. as one initial task of the entire project. Contingency costs corresponding to these buffers, depending on the data that the planner has at his disposal, can be determined using different methods, but always depend on the costs of all tasks protected by each buffer. The paper presents an exemplary schedule for a facility and the method of determining locations and cost for buffers CB and PCB, as well as their influence on the course of the curve illustrating the budgeted cost of work scheduled (BCWS. The proposed solution has been adjusted and presented with consideration of the possibilities created by the scheduling software MS Project, though its general assumptions may be implemented with application of other similar specialist tools.

Influence of cementation on the deformation properties of bentonite/quartz buffer substance

International Nuclear Information System (INIS)

Pusch, R.

1977-06-01

Cementation, e.g.precipitation of crystalline or solid amorphous inorganic substance between individual grains, greatly affects the mechanical properties of fine-grained soils. As concerns the buffer mass with the composition suggested (10 weight percent bentonite and 90% quartz particles) the intergranular contact pressure between the quartz particles will not be able to cause 'pressure solution'. Also, the other possible cementation effects will be negligible with the exception of the process which leads to precipitation of SiO 2 dissolved from quartz particles and enriched in the interstitial pore space. This process and its consequences will be treated in this report. The nature of silica solution and precipitation is not known in detail. The chemical environment, temperature, pH and ion strength are known to be controlling factors which combine to make possible alternating solution and precipitation of silica. However, as shown by the case survey and the presented theoretical treatment the amount of precipitated SiO 2 will not be able to produce a brittle behaviour of the buffer mass even after thousands of years

Buffer design 2012

International Nuclear Information System (INIS)

Juvankoski, M.

2013-08-01

Posiva's spent nuclear fuel disposal is based on the KBS-3V concept and on the characteristics of the Olkiluoto site. In this concept single canisters containing spent nuclear fuel surrounded by a bentonite buffer are emplaced in individual vertical boreholes drilled in the floor of deposition tunnels in bedrock at about 420 m depth below ground level. Disk type bentonite blocks are installed at the bottom of the hole and on the top of the disposal canister. Ring type bentonite blocks surround the canisters. This report describes the detailed design of the buffer for a KBS-3V repository. The report presents the design basis, the reference design, and summarises the performance analyses carried out for the design. This report addresses aspects concerning the manufacture, quality control, mechanical strength, chemical resistance, thermal dimensioning, handling of buffer components and material ageing phenomena including the effect of radiation. Interaction of buffer and other engineered barriers are included in the study. The long-term evolution of the repository and its effective drivers are considered if they have an impact on the buffer performance but operational safety aspects are also included because they may affect long-term safety. (orig.)

Continuous processing of recombinant proteins: integration of refolding and purification using simulated moving bed size-exclusion chromatography with buffer recycling.

Science.gov (United States)

Wellhoefer, Martin; Sprinzl, Wolfgang; Hahn, Rainer; Jungbauer, Alois

2014-04-11

Continuous processing of recombinant proteins was accomplished by combining continuous matrix-assisted refolding and purification by tandem simulated moving bed (SMB) size-exclusion chromatography (SEC). Recombinant proteins, N(pro) fusion proteins from inclusion bodies were dissolved with NaOH and refolded in the SMB system with a closed-loop set-up with refolding buffer as the desorbent buffer and buffer recycling of the refolding buffer of the raffinate by tangential flow filtration. For further purification of the refolded proteins, a second SMB operation also based on SEC was added. The whole system could be operated isocratically with refolding buffer as the desorbent buffer, and buffer recycling could also be applied in the purification step. Thus, a significant reduction in buffer consumption was achieved. The system was evaluated with two proteins, the N(pro) fusion pep6His and N(pro) fusion MCP-1. Refolding solution, which contained residual N(pro) fusion peptide, the cleaved autoprotease N(pro), and the cleaved target peptide was used as feed solution. Full separation of the cleaved target peptide from residual proteins was achieved at a purity and recovery in the raffinate and extract, respectively, of approximately 100%. In addition, more than 99% of the refolding buffer of the raffinate was recycled. A comparison of throughput, productivity, and buffer consumption of the integrated continuous process with two batch processes demonstrated that up to 60-fold higher throughput, up to 180-fold higher productivity, and at least 28-fold lower buffer consumption can be obtained by the integrated continuous process, which compensates for the higher complexity. Copyright © 2014 Elsevier B.V. All rights reserved.

OPTIMISATION OF BUFFER SIZE FOR ENHANCING QOS OF VIDEO TRAFFIC USING CROSS LAYERED HYBRID TRANSPORT LAYER PROTOCOL APPROACH

OpenAIRE

S. Matilda; B. Palaniappan

2011-01-01

Video streaming is gaining importance, with the wide popularity of multimedia rich applications in the Internet. Video streams are delay sensitive and require seamless flow for continuous visualization. Properly designed buffers offer a solution to queuing delay. The diagonally opposite QoS metrics associated with video traffic poses an optimization problem, in the design of buffers. This paper is a continuation of our previous work [1] and deals with the design of buffers. It aims at finding...

Survey of Swedish buffer material candidates and methods for characterization

International Nuclear Information System (INIS)

Erlstroem, M.; Pusch, R.

1987-12-01

The study has given a good overview of potential clay buffer candidates in the part of Sweden that offers the best possibilities to find large accessible quantities of smectitic materials. The most promising Scanian materials are those in the Kaageroed and Vallaakra (Margreteberg) areas since they represent the most smectitic ones, which may serve as raw material for the production of canister embedment. The moraine clays in the Lund-Landskrona region seem to be useful for backfilling purposes. A refined version of Reynolds technique is suggested as an SKB standard for prospecting and characterization of buffer materials. (orig./DG)

Aqueous solution dispersement of carbon nanotubes

Science.gov (United States)

Kim, Jae-Woo (Inventor); Park, Cheol (Inventor); Choi, Sang H. (Inventor); Lillehei, Peter T. (Inventor); Harrison, Joycelyn S. (Inventor)

2011-01-01

Carbon nanotubes (CNTs) are dispersed in an aqueous buffer solution consisting of at least 50 weight percent water and a remainder weight percent that includes a buffer material. The buffer material has a molecular structure defined by a first end, a second end, and a middle disposed between the first and second ends. The first end is a cyclic ring with nitrogen and oxygen heteroatomes, the middle is a hydrophobic alkyl chain, and the second end is a charged group.

Control of short-channel effects in InAlN/GaN high-electron mobility transistors using graded AlGaN buffer

Science.gov (United States)

Han, Tiecheng; Zhao, Hongdong; Peng, Xiaocan; Li, Yuhai

2018-04-01

A graded AlGaN buffer is designed to realize the p-type buffer by inducing polarization-doping holes. Based on the two-dimensional device simulator, the effect of the graded AlGaN buffer on the direct-current (DC) and radio-frequency (RF) performance of short-gate InAlN/GaN high-electron mobility transistors (HEMTs) are investigated, theoretically. Compared to standard HEMT, an enhancement of electron confinement and a good control of short-channel effect (SCEs) are demonstrated in the graded AlGaN buffer HEMT. Accordingly, the pinched-off behavior and the ability of gate modulation are significantly improved. And, no serious SCEs are observed in the graded AlGaN buffer HEMT with an aspect ratio (LG/tch) of about 6.7, much lower than that of the standard HEMT (LG/tch = 13). In addition, for a 70-nm gate length, a peak current gain cutoff frequency (fT) of 171 GHz and power gain cutoff frequency (fmax) of 191 GHz are obtained in the grade buffer HEMT, which are higher than those of the standard one with the same gate length.

Double-layered buffer to enhance the thermal performance in a high-level radioactive waste disposal system

International Nuclear Information System (INIS)

Choi, Heui-Joo; Choi, Jongwon

2008-01-01

A thermal performance is one of the most important factors in the design of a geological disposal system for high-level radioactive wastes. According to the conceptual design of the Korean Reference disposal System, the maximum temperature of its buffer with a domestic Ca-bentonite is close to the thermal criterion, 100 deg. C. In order to improve the thermal conductivity of its buffer, several kinds of additives are compared. Among the additives, graphite shows the best result in that the thermal conductivity of the bentonite block is more than 2.0 W/m deg. C. We introduced the concept of a double-layered buffer instead of a traditional bentonite block in order to use the applied additive more effectively. The thermal analysis, based upon the three-dimensional finite element method, shows that a double-layered buffer could reduce the maximum temperature on a canister's surface by 7 deg. C under identical conditions when compared with a single-layered buffer. An analytical solution was derived to efficiently analyze the effects of a double-layered buffer. The illustrative cases show that the temperature differences due to a double-layered buffer depend on the thickness of the buffer

Chemical-bath ZnO buffer layer for CuInS{sub 2} thin-film solar cells

Energy Technology Data Exchange (ETDEWEB)

Ennaoui, A.; Weber, M.; Scheer, R.; Lewerenz, H.J. [Hahn-Meitner-Institut, Abt. Grenzflaechen, Bereich Physikalische Chemie, Glienicker Strasse 100, D-14109 Berlin (Germany)

1998-07-13

ZnO buffer layers were grown by a chemical-bath deposition (CBD) in order to improve the interface quality in p-CuInS{sub 2} based solar cells, to improve the light transmission in the blue wavelength region, but also as an alternative to eliminate the toxic cadmium. The process consists of immersion of different substrates (glass, CIS) in a dilute solution of tetraamminezinc II, [Zn(NH{sub 2}){sub 4}]{sup 2+}, complex at 60-95C. During the growth process, a homogeneous growth mechanism which proceeds by the sedimentation of a mixture of ZnO and Zn(OH){sub 2} clusters formed in solution, competes with the heterogeneous growth mechanism. The mechanism consists of specific adsorption of a complex Zn(II) followed by a chemical reaction. The last process of growth results in thin, hard, adherent and specularly reflecting films. The characterization of the deposited CBD-ZnO layers was performed by X-ray diffraction (XRD), optical transmittance, scanning electron microscopy, transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). The as-deposited films on glass show hexagonal zincite structure with two preferred orientations (1 0 0) and (1 0 1). High optical transmittance up to 80% in the near-infrared and part of the visible region was observed. The low growth rate of the films on CIS suggests an atomic layer-by-layer growth process.The device parameters and performance are compared to heterojunction with a standard CdS buffer layer

Evaluation of amine inhibitors for suitability as crevice buffering agents

International Nuclear Information System (INIS)

Jayaweera, P.; Hettiarachchi, S.

1994-03-01

This report describes the results of a research effort to evaluate the suitability of some selected amines and amino acids as a crevice-buffering agents in pressurized water reactor (PWR) steam generators. The amines may be useful for buffering acid crevices, and the amino acids, because they contain both acidic and basic groups, may be useful for acidic and caustic crevices. Five commercially available amines and two amino acids were studied during this research. The study involved (1) the hydrolysis of these commercially available amines and amino acids, including measurement of their kinetics of decomposition, in simulated steam generator bulk water at 290 C, and (2) determination of their thermal stability in a simulated crevice environment. The study showed that, although the high-molecular-weight amines undergo hydrothermal decomposition, they have a better buffering capacity than their low-molecular-weight counterparts at 290 C. The amines provide effective crevice buffering by increasing the pH of the crevice solution by as much as 2.84 and to 4.24 units in the experimental setup used in this program. It was concluded that polyamines provide excellent buffering of the simulated crevice environment at 290 C and morpholine remains the best low-molecular-weight amine investigated. However, detailed volatility studies of the amines were not considered in this work. Such data would be needed before in-plant testing to ensure that the amines can concentrate in steam generator crevices to the levels assumed in this study

Investigation of some critical parameters of buffer conditions for the development of quantum dots-based optical sensors

International Nuclear Information System (INIS)

Yuan Jipei; Guo Weiwei; Wang Erkang

2008-01-01

The unique surface-sensitive properties make quantum dots (QDs) great potential in the development of sensors for various analytes. However, quantum dots are not only sensitive to a certain analyte, but also to the surrounding conditions. The controlled response to analyte may be the first step in the designing of functional quantum dots sensors. In this study, taking the quenching effect of benzoquinone (BQ) on CdTe QDs as model, several critical parameters of buffer solution conditions with potential effect on the sensors were investigated. The pH value and the concentration of sodium citrate in the buffer solution critically influenced the quenching effects of BQ. Dozens folds elevation of the quenching extents were observed with the increase of concentrations of H + and sodium citrate, and the quenching mechanisms were also fundamentally different with the changes of the surrounding buffer solutions. The quenching models were proposed and analyzed at different buffer conditions. Taking pH values for example, QDs quenching obeyed the sphere of effective quenching model with the sphere radii of 8.29 nm at pH 8.0, the linear Stern-Volmer equation with Stern-Volmer constant of 2.0 x 10 3 mol -1 L at pH 7.0, and the two binding site static quenching model at basic conditions. The elucidation of parameters for assay performance was important in the development of QDs-based optical sensors

Efficient Polymer Solar Cells with Alcohol-Soluble Zirconium(IV Isopropoxide Cathode Buffer Layer

Directory of Open Access Journals (Sweden)

Zhen Luo

2018-02-01

Full Text Available Interfacial materials are essential to the performance and stability of polymer solar cells (PSCs. Herein, solution-processed zirconium(IV isopropoxide (Zr[OCH(CH32]4, ZrIPO has been employed as an efficient cathode buffer layer between the Al cathode and photoactive layer. The ZrIPO buffer layer is prepared simply via spin-coating its isopropanol solution on the photoactive layer at room temperature without any post-treatment. When using ZrIPO/Al instead of the traditionally used Ca/Al cathode in PSCs, the short-circuit current density (Jsc is significantly improved and the series resistance of the device is decreased. The power conversion efficiency (PCE of the P3HT:PCBM-based device with ZrIPO buffer layer reaches 4.47% under the illumination of AM1.5G, 100 mW/cm2. A better performance with PCE of 8.07% is achieved when a low bandgap polymer PBDTBDD is selected as donor material. The results indicate that ZrIPO is a promising electron collection material as a substitute of the traditional low-work-function cathode for high performance PSCs.

Study on chemical buffering property of GMZ sodium bentonite under atmospheric condition

International Nuclear Information System (INIS)

Wen Zhijian

2012-01-01

At present, the deep geological disposal is regarded as the most reasonable and effective way to safely disposal the high-level radioactive wastes in the world. The conceptual model of HLW geological disposal in China is based on a multi-barrier system that combines an isolating geological environment with an engineered barrier system. The buffer is one of the engineered barrier materials and GMZ Na-bentonite is selected as the basic material. One of the most important functions related to buffer is the chemical buffering, which means buffering the changes in pore water chemistry. This paper presents the experiments of GMZ-1 Na-bentonite reacted with distilled water under atmospheric condition. The batch tests and results discussion are reported. Na and Mg in batch test solution are co-provided by interlayer cations of montmorillonite and solids dissolution, K and Ca are provided by dissolution of solids. The result is a pre-requisite for predicting near-field nuclide migration and assesses the long-term stability of the engineered barrier materials. (author)

21 CFR 520.1696a - Buffered penicillin powder, penicillin powder with buffered aqueous diluent.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Buffered penicillin powder, penicillin powder with... FORM NEW ANIMAL DRUGS § 520.1696a Buffered penicillin powder, penicillin powder with buffered aqueous diluent. (a) Specifications. When reconstituted, each milliliter contains penicillin G procaine equivalent...

A pyruvate-buffered dialysis fluid induces less peritoneal angiogenesis and fibrosis than a conventional solution

NARCIS (Netherlands)

van Westrhenen, Roos; Zweers, Machteld M.; Kunne, Cindy; de Waart, Dirk R.; van der Wal, Allard C.; Krediet, Raymond T.

2008-01-01

BACKGROUND: Conventional lactate-buffered peritoneal dialysis (PD) fluids containing glucose and glucose degradation products are believed to contribute to the development of fibrosis and angiogenesis in the dialyzed peritoneum. To reduce potential negative effects of lactate, pyruvate was

Investigating multiple solutions in the constrained minimal supersymmetric standard model

Energy Technology Data Exchange (ETDEWEB)

Allanach, B.C. [DAMTP, CMS, University of Cambridge,Wilberforce Road, Cambridge, CB3 0HA (United Kingdom); George, Damien P. [DAMTP, CMS, University of Cambridge,Wilberforce Road, Cambridge, CB3 0HA (United Kingdom); Cavendish Laboratory, University of Cambridge,JJ Thomson Avenue, Cambridge, CB3 0HE (United Kingdom); Nachman, Benjamin [SLAC, Stanford University,2575 Sand Hill Rd, Menlo Park, CA 94025 (United States)

2014-02-07

Recent work has shown that the Constrained Minimal Supersymmetric Standard Model (CMSSM) can possess several distinct solutions for certain values of its parameters. The extra solutions were not previously found by public supersymmetric spectrum generators because fixed point iteration (the algorithm used by the generators) is unstable in the neighbourhood of these solutions. The existence of the additional solutions calls into question the robustness of exclusion limits derived from collider experiments and cosmological observations upon the CMSSM, because limits were only placed on one of the solutions. Here, we map the CMSSM by exploring its multi-dimensional parameter space using the shooting method, which is not subject to the stability issues which can plague fixed point iteration. We are able to find multiple solutions where in all previous literature only one was found. The multiple solutions are of two distinct classes. One class, close to the border of bad electroweak symmetry breaking, is disfavoured by LEP2 searches for neutralinos and charginos. The other class has sparticles that are heavy enough to evade the LEP2 bounds. Chargino masses may differ by up to around 10% between the different solutions, whereas other sparticle masses differ at the sub-percent level. The prediction for the dark matter relic density can vary by a hundred percent or more between the different solutions, so analyses employing the dark matter constraint are incomplete without their inclusion.

Strontium Titanate Buffer Layers on Cu/33%Ni Substrates using a Novel Solution Chemistry

DEFF Research Database (Denmark)

Pallewatta, Pallewatta G A P; Yue, Zhao; Hui, Tian

2013-01-01

SrTiO3 is a widely studied perovskite material due to its advantages as a buffer template which can be simply applied between a metal substrate tape and a superconducting layer in 2G high temperature superconducting (HTS) tapes. In this study, heteroepitaxial SrTiO3 thin films were deposited on t...

Improving Water Quality With Conservation Buffers

Science.gov (United States)

Lowrance, R.; Dabney, S.; Schultz, R.

2003-12-01

Conservation buffer technologies are new approaches that need wider application. In-field buffer practices work best when used in combination with other buffer types and other conservation practices. Vegetative barriers may be used in combination with edge-of-field buffers to protect and improve their function and longevity by dispersing runoff and encouraging sediment deposition upslope of the buffer. It's important to understand how buffers can be managed to help reduce nutrient transport potential for high loading of nutrients from manure land application sites, A restored riparian wetland buffer retained or removed at least 59 percent of the nitrogen and 66 percent of the phosphorus that entered from an adjacent manure land application site. The Bear Creek National Restoration Demonstration Watershed project in Iowa has been the site of riparian forest buffers and filter strips creation; constructed wetlands to capture tile flow; stream-bank bioengineering; in-stream structures; and controlling livestock grazing. We need field studies that test various widths of buffers of different plant community compositions for their efficacy in trapping surface runoff, reducing nonpoint source pollutants in subsurface waters, and enhancing the aquatic ecosystem. Research is needed to evaluate the impact of different riparian grazing strategies on channel morphology, water quality, and the fate of livestock-associated pathogens and antibiotics. Integrating riparian buffers and other conservation buffers into these models is a key objective in future model development.

Volumetric properties of MES, MOPS, MOPSO, and MOBS in water and in aqueous electrolyte solutions

International Nuclear Information System (INIS)

Taha, Mohamed; Lee, Ming-Jer

2010-01-01

4-Morpholineethanesulfonic acid (MES), 4-morpholinepropanesulfonic acid (MOPS), 3-morpholino-2-hydroxypropanesulfonic acid (MOPSO), and 4-(N-morpholino)butanesulfonic acid (MOBS), are useful for pH control as standard buffers in the physiological region of 5.5-6.7 for MES, 6.5-7.9 for MOPS, 6.2-7.6 for MOPSO, and 6.9-8.3 for MOBS, respectively. On the basis of density measurements at 298.15 K, the apparent molar volumes, V φ , of the above-mentioned buffers in water and in (0.05, 0.16, and 0.25) mol kg -1 aqueous solutions of NaCl, KCl, KBr, and CH 3 COOK have been calculated. The partial molar volumes at infinite dilution, V φ o , obtained from V φ , have been used to calculate the volume of transfer, Δ tr V φ o , from water to aqueous electrolyte solutions. It was found that both V φ o and Δ tr V φ o vary linearly with increasing the number of carbon atoms in the alkyl group side chain of the zwitterionic buffers. These linear correlations have been utilized to estimate the contributions of the zwitterionic end group (morpholinium ion, -SO 3 - ) and -CH 2 - group to V φ o and Δ tr V φ o . The values of V φ o and Δ tr V φ o for some functional group contributions of the zwittierionic buffers with salts have also been reported.

Mechanisms of buffer therapy resistance.

Science.gov (United States)

Bailey, Kate M; Wojtkowiak, Jonathan W; Cornnell, Heather H; Ribeiro, Maria C; Balagurunathan, Yoganand; Hashim, Arig Ibrahim; Gillies, Robert J

2014-04-01

Many studies have shown that the acidity of solid tumors contributes to local invasion and metastasis. Oral pH buffers can specifically neutralize the acidic pH of tumors and reduce the incidence of local invasion and metastatic formation in multiple murine models. However, this effect is not universal as we have previously observed that metastasis is not inhibited by buffers in some tumor models, regardless of buffer used. B16-F10 (murine melanoma), LL/2 (murine lung) and HCT116 (human colon) tumors are resistant to treatment with lysine buffer therapy, whereas metastasis is potently inhibited by lysine buffers in MDA-MB-231 (human breast) and PC3M (human prostate) tumors. In the current work, we confirmed that sensitive cells utilized a pH-dependent mechanism for successful metastasis supported by a highly glycolytic phenotype that acidifies the local tumor microenvironment resulting in morphological changes. In contrast, buffer-resistant cell lines exhibited a pH-independent metastatic mechanism involving constitutive secretion of matrix degrading proteases without elevated glycolysis. These results have identified two distinct mechanisms of experimental metastasis, one of which is pH-dependent (buffer therapy sensitive cells) and one which is pH-independent (buffer therapy resistant cells). Further characterization of these models has potential for therapeutic benefit. Copyright © 2014 Neoplasia Press, Inc. Published by Elsevier Inc. All rights reserved.

Analysis of influence of buffer layers on microwave propagation through high-temperature superconducting thin films

International Nuclear Information System (INIS)

Ceremuga, J.; Barton, M.; Miranda, F.

1994-01-01

Methods of analysis of microwave propagation through superconducting thin films with buffer layers on dielectric substrates have been discussed. Expressions describing the transmission coefficient S 21 through the structure and the complex conductivity sigma of a superconductor in an analytical form have been derived. The derived equations are valid for microwave propagation in waveguides as well as in free space with relevant definition of impedances. Using the obtained solutions, the influences of buffer layers' parameters (thickness, relative permittivity and loss tangent) on the transmission coefficient has been investigated using MATLAB. Simulations have been performed for 10 GHz transmission through YBa 2 Cu 3 O 7 films on sapphire with SrTiO 3 and CeO 2 buffer layers and on silicon with CaF 2 and YSZ buffer layers. To illustrate the simulations, measurements of the transmission through YBCO film on sapphire with SrTiO 3 buffer layer have been performed. It has been shown that even lossy buffer layers have very little impact (smaller than 1% in magnitude and 0.3% in phase) on the transmission coefficient through superconducting thin films, providing their thickness is below 10 mu m. (author)

Dakin Solution Alters Macrophage Viability and Function

Science.gov (United States)

2014-07-18

fungi, viruses, and parasites [1]. Dakin’s solution (DS) is buffered sodium hypochlorite, which has a long history of use as a topical antiseptic in...eagle medium (DMEM) supplemented with 10% fetal bovine serum, 10 U/mL penicillin, 10 mg/mL streptomycin, and maintained at 37C in 5% CO2. DS (buffered

Corrosion in low dielectric constant Si-O based thin films: Buffer concentration effects

International Nuclear Information System (INIS)

Zeng, F. W.; Lane, M. W.; Gates, S. M.

2014-01-01

Organosilicate glass (OSG) is often used as an interlayer dielectric (ILD) in high performance integrated circuits. OSG is a brittle material and prone to stress-corrosion cracking reminiscent of that observed in bulk glasses. Of particular concern are chemical-mechanical planarization techniques and wet cleans involving solvents commonly encountered in microelectronics fabrication where the organosilicate film is exposed to aqueous environments. Previous work has focused on the effect of pH, surfactant, and peroxide concentration on the subcritical crack growth of these films. However, little or no attention has focused on the effect of the conjugate acid/base concentration in a buffer. Accordingly, this work examines the “strength” of the buffer solution in both acidic and basic environments. The concentration of the buffer components is varied keeping the ratio of acid/base and therefore pH constant. In addition, the pH was varied by altering the acid/base ratio to ascertain any additional effect of pH. Corrosion tests were conducted with double-cantilever beam fracture mechanics specimens and fracture paths were verified with ATR-FTIR. Shifts in the threshold fracture energy, the lowest energy required for bond rupture in the given environment, G TH , were found to shift to lower values as the concentration of the base in the buffer increased. This effect was found to be much larger than the effect of the hydroxide ion concentration in unbuffered solutions. The results are rationalized in terms of the salient chemical bond breaking process occurring at the crack tip and modeled in terms of the chemical potential of the reactive species

Buffer Zone Fact Sheets

Science.gov (United States)

New requirements for buffer zones and sign posting contribute to soil fumigant mitigation and protection for workers and bystanders. The buffer provides distance between the pesticide application site and bystanders, reducing exposure risk.

Pressure solution of minerals in quartz-type buffer materials

International Nuclear Information System (INIS)

Erlstroem, M.

1986-12-01

Two samples, pure quartz sand and a sand-bentonite (10%) mixture, were tested under conditions of high pressure (200 bar) and temperature (115 0 C). The experiment was carried out over a period of 70 days. A series of thin slides were prepared on a resin embedded sample at the end of the test period. A microscopical study was performed as to obtain data concerning the effects of pressure and temperature. It showed that no pressure solution had taken place in the pure quartz sand. However, the individual grains had been severely fractured, thus causing significant internal sedimentation. The mixed sample showed that the clay component coated the quartz grains and significantly decreased the effect of stress in the grains by having a cushioning effect. Relative grain movement was facilitated by the clay, by which the grains rotated and slipped into stable positions with large contact areas and low contact stresses. This probably minimized pressure solution. However, a few contact regions indicated the presence of precipitated silica. The investigation shows no definite evidence of pressure solution after an experiment duration of 70 days. Since the effect of solution may be time dependent at the applied temperature, it is recommended that further experiments be conducted at higher effective and porewater pressures but still at 115 0 C. (orig.)

Potassium biphthalate buffer for pH control to optimize glycosyl hydrolase production in shake flasks using filamentous fungi

Directory of Open Access Journals (Sweden)

Patrícia dos Santos Costa

Full Text Available Abstract The optimization of culture medium with statistical methods is widely used in filamentous fungi glycosyl hydrolase production. The implementation of such methodology in bioreactors is very expensive as it requires several pH-controlled systems operating in parallel in order to test a large number of culture media components. The objective of this study was to evaluate potassium biphthalate buffer for pH control, which allows the optimization studies to be performed in shake flasks.The results have shown that buffering the culture medium with 0.1 M potassium biphthalate allowed pH control, resulting in a decrease of the standard deviation of triplicates for pH and activities of glycosyl hydrolase measurements. The use of this buffer allowed shake flask culture media optimization of enzyme production by Trichoderma harzianum, increasing the cellulase activity by more than 2 times compared to standard unbuffered culture medium. The same buffer can be used for culture media optimization of other fungi, such as Penicillium echinulatum.

Vermiculite's strong buffer capacity renders it unsuitable for studies of acidity on soybean (Glycine max L.) nodulation and growth.

Science.gov (United States)

Indrasumunar, Arief; Gresshoff, Peter M

2013-11-14

Vermiculite is the most common soil-free growing substrate used for plants in horticultural and scientific studies due to its high water holding capacity. However, some studies are not suitable to be conducted in it. The described experiments aimed to test the suitability of vermiculite to study the effect of acidity on nodulation and growth of soybean (Glycine max L.). Two different nutrient solutions (Broughton & Dilworth, and modified Herridge nutrient solutions) with or without MES buffer addition were used to irrigate soybean grown on vermiculite growth substrates. The pH of nutrient solutions was adjusted to either pH 4.0 or 7.0 prior its use. The nodulation and vegetative growth of soybean plants were assessed at 3 and 4 weeks after inoculation. The unsuitability of presumably inert vermiculite as a physical plant growth substrate for studying the effects of acidity on soybean nodulation and plant growth was illustrated. Nodulation and growth of soybean grown in vermiculite were not affected by irrigation with pH-adjusted nutrient solution either at pH 4.0 or 7.0. This was reasonably caused by the ability of vermiculite to neutralise (buffer) the pH of the supplied nutrient solution (pH 2.0-7.0). Due to its buffering capacity, vermiculite cannot be used as growth support to study the effect of acidity on nodulation and plant growth.

High-quality fiber fabrication in buffered hydrofluoric acid solution with ultrasonic agitation.

Science.gov (United States)

Zhong, Nianbing; Liao, Qiang; Zhu, Xun; Wang, Yongzhong; Chen, Rong

2013-03-01

An etching method for preparing high-quality fiber-optic sensors using a buffered etchant with ultrasonic agitation is proposed. The effects of etching conditions on the etch rate and surface morphology of the etched fibers are investigated. The effect of surface roughness is discussed on the fibers' optical properties. Linear etching behavior and a smooth fiber surface can be repeatedly obtained by adjusting the ultrasonic power and etchant pH. The fibers' spectral quality is improved as the ratio of the pit depth to size decreases, and the fibers with smooth surfaces are more sensitive to a bacterial suspension than those with rough surfaces.

Stability of buffer-free freeze-dried formulations: A feasibility study of a monoclonal antibody at high protein concentrations.

Science.gov (United States)

Garidel, Patrick; Pevestorf, Benjamin; Bahrenburg, Sven

2015-11-01

We studied the stability of freeze-dried therapeutic protein formulations over a range of initial concentrations (from 40 to 160 mg/mL) and employed a variety of formulation strategies (including buffer-free freeze dried formulations, or BF-FDF). Highly concentrated, buffer-free liquid formulations of therapeutic monoclonal antibodies (mAbs) have been shown to be a viable alternative to conventionally buffered preparations. We considered whether it is feasible to use the buffer-free strategy in freeze-dried formulations, as an answer to some of the known drawbacks of conventional buffers. We therefore conducted an accelerated stability study (24 weeks at 40 °C) to assess the feasibility of stabilizing freeze-dried formulations without "classical" buffer components. Factors monitored included pH stability, protein integrity, and protein aggregation. Because the protein solutions are inherently self-buffering, and the system's buffer capacity scales with protein concentration, we included highly concentrated buffer-free freeze-dried formulations in the study. The tested formulations ranged from "fully formulated" (containing both conventional buffer and disaccharide stabilizers) to "buffer-free" (including formulations with only disaccharide lyoprotectant stabilizers) to "excipient-free" (with neither added buffers nor stabilizers). We evaluated the impacts of varying concentrations, buffering schemes, pHs, and lyoprotectant additives. At the end of 24 weeks, no change in pH was observed in any of the buffer-free formulations. Unbuffered formulations were found to have shorter reconstitution times and lower opalescence than buffered formulations. Protein stability was assessed by visual inspection, sub-visible particle analysis, protein monomer content, charge variants analysis, and hydrophobic interaction chromatography. All of these measures found the stability of buffer-free formulations that included a disaccharide stabilizer comparable to buffer

Gamma radiation effects on vitamin C standard solutions

International Nuclear Information System (INIS)

Amaro, Jose Daniel V.; Mansur Netto, Elias

1995-01-01

This word shows the physical - chemical effects of gamma radiation on standard solutions of vitamin C. Samples with concentration of 50 mg/ml were exposed to different doses of gamma radiations: 1,0 2,5 and 5,0 kGy, using a cobalt-60 source, with storing periods of 0,15 and 30 days. The results showed a vitamin C concentration loss, with a minimum of 17% for the dose of 1,0 kGy immediately after irradiation and a maximum of 81% for the dose of 5 kGy and 30 days after irradiation. (author). 3 refs., 2 tabs

Comparison of Buffer Effect of Different Acids During Sandstone Acidizing

International Nuclear Information System (INIS)

Shafiq, Mian Umer; Mahmud, Hisham Khaled Ben; Hamid, Mohamed Ali

2015-01-01

The most important concern of sandstone matrix acidizing is to increase the formation permeability by removing the silica particles. To accomplish this, the mud acid (HF: HCl) has been utilized successfully for many years to stimulate the sandstone formations, but still it has many complexities. This paper presents the results of laboratory investigations of different acid combinations (HF: HCl, HF: H 3 PO 4 and HF: HCOOH). Hydrofluoric acid and fluoboric acid are used to dissolve clays and feldspar. Phosphoric and formic acids are added as a buffer to maintain the pH of the solution; also it allows the maximum penetration of acid into the core sample. Different tests have been performed on the core samples before and after the acidizing to do the comparative study on the buffer effect of these acids. The analysis consists of permeability, porosity, color change and pH value tests. There is more increase in permeability and porosity while less change in pH when phosphoric and formic acids were used compared to mud acid. From these results it has been found that the buffer effect of phosphoric acid and formic acid is better than hydrochloric acid. (paper)

Signature-based store checking buffer

Science.gov (United States)

Sridharan, Vilas; Gurumurthi, Sudhanva

2015-06-02

A system and method for optimizing redundant output verification, are provided. A hardware-based store fingerprint buffer receives multiple instances of output from multiple instances of computation. The store fingerprint buffer generates a signature from the content included in the multiple instances of output. When a barrier is reached, the store fingerprint buffer uses the signature to verify the content is error-free.

Matrix-Matched Iron-Oxide Laser Ablation ICP-MS U–Pb Geochronology Using Mixed Solution Standards

Directory of Open Access Journals (Sweden)

Liam Courtney-Davies

2016-08-01

Full Text Available U–Pb dating of the common iron-oxide hematite (α-Fe2O3, using laser-ablation inductively-coupled-plasma mass-spectrometry (LA-ICP-MS, provides unparalleled insight into the timing and processes of mineral deposit formation. Until now, the full potential of this method has been negatively impacted by the lack of suitable matrix-matched standards. To achieve matrix-matching, we report an approach in which a U–Pb solution and ablated material from 99.99% synthetic hematite are simultaneously mixed in a nebulizer chamber and introduced to the ICP-MS. The standard solution contains fixed U- and Pb-isotope ratios, calibrated independently, and aspiration of the isotopically homogeneous solution negates the need for a matrix-matched, isotopically homogenous natural iron-oxide standard. An additional advantage of using the solution is that the individual U–Pb concentrations and isotope ratios can be adjusted to approximate that in the unknown, making the method efficient for dating hematite containing low (~10 ppm to high (>1 wt % U concentrations. The above-mentioned advantage to this solution method results in reliable datasets, with arguably-better accuracy in measuring U–Pb ratios than using GJ-1 Zircon as the primary standard, which cannot be employed for such low U concentrations. Statistical overlaps between 207Pb/206Pb weighted average ages (using GJ-1 Zircon and U–Pb upper intercept ages (using the U–Pb mixed solution method of two samples from iron-oxide copper-gold (IOCG deposits in South Australia demonstrate that, although fractionation associated with a non-matrix matched standard does occur when using GJ-1 Zircon as the primary standard, it does not impact the 207Pb/206Pb or upper intercept age. Thus, GJ-1 Zircon can be considered reliable for dating hematite using LA-ICP-MS. Downhole fractionation of 206Pb/238U is observed to occur in spot analyses of hematite. The use of rasters in future studies will hopefully minimize

Standard physics solution to the solar neutrino problem?

Energy Technology Data Exchange (ETDEWEB)

Dar, A [Technion-Israel Inst. of Tech., Haifa (Israel). Dept. of Physics

1996-11-01

The {sup 8}B solar neutrino flux predicted by the standard solar model (SSM) is consistent within the theoretical and experimental uncertainties with that at Kamiokande. The Gallium and Chlorine solar neutrino experiments, however, seem to imply that the {sup 7}Be solar neutrino flux is strongly suppressed compared with that predicted by the SSM. If the {sup 7}Be solar neutrino flux is suppressed, still it can be due to astrophysical effects not included in the simplistic SSM. Such effects include short term fluctuations or periodic variation of the temperature in the solar core, rotational mixing of {sup 3}He in the solar core, and dense plasma effects which may strongly enhance p-capture by {sup 7}Be relative to e-capture. The new generation of solar observations which already look non stop deep into the sun, like Superkamiokande through neutrinos, and SOHO and GONG through acoustic waves, may point at the correct solution. Only Superkamiokande and/or future solar neutrino experiments, such as SNO, BOREXINO and HELLAZ, will be able to find out whether the solar neutrino problem is caused by neutrino properties beyond the minimal standard electroweak model or whether it is just a problem of the too simplistic standard solar model. (author) 1 fig., 3 tabs., refs.

Scintillation detector with anticoincidence shield for determination of the radioactive concentration of standard solutions

International Nuclear Information System (INIS)

Broda, R.; Radoszewski, T.

1982-01-01

The construction and parameters of the prototype liquid scintillation detector for disintegration rate determination of standard solutions is described. The detector is equipped with a liquid scintillation anticoincidence shield with a volume of 40 l. The instrument is placed in the building of the Radioisotope Production and Distribution Centre in the Institute of Nuclear Research at Swierk. The results of instrument background reduction are described. The counting efficiency of several beta-emitters 3 H, 63 Ni, 14 C and 90 Sr + 90 Y is given, as well as the examples of a disintegration rate determination of low radioactivity concentration of standard solutions. (author)

Acid-base characteristics of bromophenol blue-citrate buffer systems in the amorphous state.

Science.gov (United States)

Li, Jinjiang; Chatterjee, Koustuv; Medek, Ales; Shalaev, Evgenyi; Zografi, George

2004-03-01

In this study, we have examined the acid-base characteristics of various citrate buffer systems alone and in the presence of the pH indicator dye, bromophenol blue, in aqueous solution, and after lyophilization to produce amorphous material. Fourier transform Raman and solid-state nuclear magnetic resonance spectroscopy have been used to monitor the ratio of ionized to un-ionized citric acid under various conditions, as a function of initial pH in the range of 2.65-4.28. Ultraviolet-visible spectrophotometry was used to probe the extent of proton transfer of bromophenol blue in the citrate buffer systems in solution and the amorphous state. Spectroscopic studies indicated greater ionization of citric acid and bromophenol blue in solution and the solid state with increasing initial solution pH, as expected. Fourier transform Raman measurements indicated the same ratio of ionized to un-ionized citrate species in solution, frozen solution, and the amorphous state. It is shown that the ratio of species at any particular initial pH is primarily determined by the amount of sodium ion present so as to maintain electroneutrality and not necessarily to the fact that pH and pK(a) remain unchanged during freezing and freeze drying. Indeed, for bromophenol blue, the relative ultraviolet-visible intensities for ionized and un-ionized species in the amorphous sample were different from those in solution indicating that the extent of protonation of bromophenol blue was significantly lower in the solid samples. It is concluded that under certain conditions there can be significant differences in the apparent hydrogen activity of molecules in amorphous systems. Copyright 2004 Wiley-Liss, Inc. and the American Pharmacists Association

Solution processed transition metal oxide anode buffer layers for efficiency and stability enhancement of polymer solar cells

Science.gov (United States)

Ameen, M. Yoosuf; Shamjid, P.; Abhijith, T.; Reddy, V. S.

2018-01-01

Polymer solar cells were fabricated with solution-processed transition metal oxides, MoO3 and V2O5 as anode buffer layers (ABLs). The optimized device with V2O5 ABL exhibited considerably higher power conversion efficiency (PCE) compared to the devices based on MoO3 and poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) ABLs. The space charge limited current measurements and impedance spectroscopy results of hole-only devices revealed that V2O5 provided a very low charge transfer resistance and high hole mobility, facilitating efficient hole transfer from the active layer to the ITO anode. More importantly, incorporation of V2O5 as ABL resulted in substantial improvement in device stability compared to MoO3 and PEDOT:PSS based devices. Unencapsulated PEDOT:PSS-based devices stored at a relative humidity of 45% have shown complete failure within 96 h. Whereas, MoO3 and V2O5 based devices stored in similar conditions retained 22% and 80% of their initial PCEs after 96 h. Significantly higher stability of the V2O5-based device is ascribed to the reduction in degradation of the anode/active layer interface, as evident from the electrical measurements.

Standard specification for leak detector solutions intended for use on brasses and other copper alloys

CERN Document Server

American Society for Testing and Materials. Philadelphia

2005-01-01

1.1 This specification covers the requirements for leak detector solutions suitable for use in checking the leakage of valves, pipes, fittings, joints, and so forth of a pressurized gas system fabricated from brasses and other copper alloys. 1.2 This specification deals with the stress corrosion cracking aspect of leak detector solutions. The effectiveness, chemical, physical and mechanical properties of leak detector solutions are not within the scope of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

Solution-processed In2S3 buffer layer for chalcopyrite thin film solar cells

OpenAIRE

Wang Lan; Lin Xianzhong; Ennaoui Ahmed; Wolf Christian; Lux-Steiner Martha Ch.; Klenk Reiner

2016-01-01

We report a route to deposit In2S3 thin films from air-stable, low-cost molecular precursor inks for Cd-free buffer layers in chalcopyrite-based thin film solar cells. Different precursor compositions and processing conditions were studied to define a reproducible and robust process. By adjusting the ink properties, this method can be applied in different printing and coating techniques. Here we report on two techniques, namely spin-coating ...

Developing suitable buffers to capture transport cycling behavior

DEFF Research Database (Denmark)

Madsen, Thomas; Schipperijn, Jasper; Christiansen, Lars Breum

2014-01-01

units (e.g., home-buffer-based neighborhoods) are not necessarily representative for environmental exposure. An increased understanding of appropriate neighborhoods is needed. GPS cycling tracks from 78 participants for 7 days form the basis for the development and testing of different neighborhood...... buffers for transport cycling. The percentage of GPS points per square meter was used as indicator of the effectiveness of a series of different buffer types, including home-based network buffers, shortest route to city center buffers, and city center-directed ellipse-shaped buffers. The results show...... center-directed ellipse-shaped buffers yielded better results than traditional home-based network buffer types. The ellipse-shaped buffer types could therefore be considered an alternative to more traditional buffers or administrative units in future studies of transport cycling behavior....

RESEARCH NEEDS IN RIPARIAN BUFFER RESTORATION

Science.gov (United States)

Riparian buffer restorations are used as management tools to produce favorable water quality impacts; moreover, the basis for riparian buffers as an instrument of water quality restoration rests on a relatively firm foundation. However, the extent to which buffers can restore rip...

Buffer sizing for multi-hop networks

KAUST Repository

Shihada, Basem

2014-01-28

A cumulative buffer may be defined for an interference domain in a wireless mesh network and distributed among nodes in the network to maintain or improve capacity utilization of network resources in the interference domain without increasing packet queuing delay times. When an interference domain having communications links sharing resources in a network is identified, a cumulative buffer size is calculated. The cumulative buffer may be distributed among buffers in each node of the interference domain according to a simple division or according to a cost function taking into account a distance of the communications link from the source and destination. The network may be monitored and the cumulative buffer size recalculated and redistributed when the network conditions change.

Aspartate buffer and divalent metal ions affect oxytocin in aqueous solution and protect it from degradation

DEFF Research Database (Denmark)

Avanti, Christina; Oktaviani, Nur Alia; Hinrichs, Wouther L.J.

2013-01-01

Oxytocin is a peptide drug used to induce labor and prevent bleeding after childbirth. Due to its instability, transport and storage of oxytocin formulations under tropical conditions is problematic. In a previous study, we have found that the stability of oxytocin in aspartate buffered formulati...

Aspartate buffer and divalent metal ions affect oxytocin in aqueous solution and protect it from degradation

NARCIS (Netherlands)

Avanti, Christina; Oktaviani, Nur Alia; Hinrichs, Wouter L J; Frijlink, Henderik W; Mulder, Frans A A

2013-01-01

Oxytocin is a peptide drug used to induce labor and prevent bleeding after childbirth. Due to its instability, transport and storage of oxytocin formulations under tropical conditions is problematic. In a previous study, we have found that the stability of oxytocin in aspartate buffered formulation

Buffer-regulated biocorrosion of pure magnesium.

Science.gov (United States)

Kirkland, Nicholas T; Waterman, Jay; Birbilis, Nick; Dias, George; Woodfield, Tim B F; Hartshorn, Richard M; Staiger, Mark P

2012-02-01

Magnesium (Mg) alloys are being actively investigated as potential load-bearing orthopaedic implant materials due to their biodegradability in vivo. With Mg biomaterials at an early stage in their development, the screening of alloy compositions for their biodegradation rate, and hence biocompatibility, is reliant on cost-effective in vitro methods. The use of a buffer to control pH during in vitro biodegradation is recognised as critically important as this seeks to mimic pH control as it occurs naturally in vivo. The two different types of in vitro buffer system available are based on either (i) zwitterionic organic compounds or (ii) carbonate buffers within a partial-CO(2) atmosphere. This study investigated the influence of the buffering system itself on the in vitro corrosion of Mg. It was found that the less realistic zwitterion-based buffer did not form the same corrosion layers as the carbonate buffer, and was potentially affecting the behaviour of the hydrated oxide layer that forms on Mg in all aqueous environments. Consequently it was recommended that Mg in vitro experiments use the more biorealistic carbonate buffering system when possible.

Dual-Analyte Fluorescent Sensor Based on [5]Helicene Derivative with Super Large Stokes Shift for the Selective Determinations of Cu2+ or Zn2+ in Buffer Solutions and Its Application in a Living Cell.

Science.gov (United States)

Sakunkaewkasem, Siwakorn; Petdum, Anuwut; Panchan, Waraporn; Sirirak, Jitnapa; Charoenpanich, Adisri; Sooksimuang, Thanasat; Wanichacheva, Nantanit

2018-05-10

A new fluorescent sensor, M201-DPA, based on [5]helicene derivative was utilized as dual-analyte sensor for determination of Cu 2+ or Zn 2+ in different media and different emission wavelengths. The sensor could provide selective and bifunctional determination of Cu 2+ in HEPES buffer containing Triton-X100 and Zn 2+ in Tris buffer/methanol without interference from each other and other ions. In HEPES buffer, M201-DPA demonstrated the selective ON-OFF fluorescence quenching at 524 nm toward Cu 2+ . On the other hand, in Tris buffer/methanol, M201-DPA showed the selective OFF-ON fluorescence enhancement upon the addition of Zn 2+ , which was specified by the hypsochromic shift at 448 nm. Additionally, M201-DPA showed extremely large Stokes shifts up to ∼150 nm. By controlling the concentration of Zn 2+ and Cu 2+ in a living cell, the imaging of a HepG2 cellular system was performed, in which the fluorescence of M201-DPA in the blue channel was decreased upon addition of Cu 2+ and was enhanced in UV channel upon addition of Zn 2+ . The detection limits of M201-DPA for Cu 2+ and Zn 2+ in buffer solutions were 5.6 and 3.8 ppb, respectively. Importantly, the Cu 2+ and Zn 2+ detection limits of the developed sensors were significantly lower than permitted Cu 2+ and Zn 2+ concentrations in drinking water as established by the U.S. EPA and WHO.

Comparison of zwitterionic N-alkylaminomethanesulfonic acids to related compounds in the Good buffer series

Directory of Open Access Journals (Sweden)

Robert D. Long

2010-04-01

Full Text Available Several N-alkyl and N,N-dialkylaminomethanesulfonic acids were synthesized (as zwitterions and/or sodium salts to be tested for utility as biological buffers at lower pH levels than existing Good buffer compounds (aminoalkanesulfonates with a minimum of two carbons between amine and sulfonic acid groups as originally described by Norman Good, and in common use as biological buffers. Our hypothesis was that a shorter carbon chain (one carbon between the amino and sulfonic acid groups should lower the ammonium ion pKa values. The alkylaminomethanesulfonate compounds were synthesized in aqueous solution by reaction of primary or secondary amines with formaldehyde/sodium hydrogensulfite addition compound. The pKa values of the ammonium ions of this series of compounds (compared to existing Good buffers was found to correlate well with the length of the carbon chain between the amino and sulfonate moeties, with a significant decrease in amine basicity in the aminomethanesulfonate compounds (pKa decrease of 2 units or more compared to existing Good buffers. An exception was found for the 2-hydroxypiperazine series which shows only a small pKa decrease, probably due to the site of protonation in this compound (as confirmed by X-ray crystal structure. X-ray crystallographic structures of two members of the series are reported. Several of these compounds have pKa values that would indicate potential utility for buffering at pH levels below the normal physiological range (pKa values in the range of 3 to 6 without aqueous solubility problems – a range that is problematic for currently available Good buffers. Unfortunately, the alkylaminomethanesulfonates were found to degrade (with loss of their buffering ability at pH levels below the pKa value and were unstable at elevated temperature (as when autoclaving – thus limiting their utility.

A magnetic trap for living cells suspended in a paramagnetic buffer

Science.gov (United States)

Winkleman, Adam; Gudiksen, Katherine L.; Ryan, Declan; Whitesides, George M.; Greenfield, Derek; Prentiss, Mara

2004-09-01

This manuscript describes the fabrication and use of a three-dimensional magnetic trap for diamagnetic objects in an aqueous solution of paramagnetic ions; this trap uses permanent magnets. It demonstrates trapping of polystyrene spheres, and of various types of living cells: mouse fibroblast (NIH-3T3), yeast (Saccharomyces cerevisiae), and algae (Chlamydomonas reinhardtii). For a 40mM solution of gadolinium (III) diethylenetriaminepentaacetic acid (Gd .DTPA) in aqueous buffer, the smallest cell (particle) that could be trapped had a radius of ˜2.5μm. The trapped particle and location of the magnetic trap can be translated in three dimensions by independent manipulation of the permanent magnets. This letter a1so characterizes the biocompatibility of the trapping solution.

The stability of DLC film on nitrided CoCrMo alloy in phosphate buffer solution

International Nuclear Information System (INIS)

Zhang, T.F.; Liu, B.; Wu, B.J.; Liu, J.; Sun, H.; Leng, Y.X.; Huang, N.

2014-01-01

CoCrMo alloy is often used as the material for metal artificial joint, but metal debris and metal ions are the main concern on tissue inflammation or tissue proliferation for metal prosthesis. In this paper, nitrogen ion implantation and diamond like carbon (DLC) film composite treatment was used to reduce the wear and ion release of biomedical CoCrMo substrate. The mechanical properties and stability of N-implanted/DLC composite layer in phosphate buffer solution (PBS) was evaluated to explore the full potential of N-implanted/DLC composite layer as an artificial joint surface modification material. The results showed that the DLC film on N implanted CoCrMo (N-implanted/DLC composite layer) had the higher surface hardness and wear resistance than the DLC film on virgin CoCrMo alloy, which was resulted from the strengthen effect of the N implanted layer on CoCrMo alloy. After 30 days immersion in PBS, the structure of DLC film on virgin CoCrMo or on N implanted CoCrMo had no visible change. But the adhesion and corrosion resistance of DLC on N implanted CoCrMo (N-implanted/DLC composite layer) was weakened due to the dissolution of the N implanted layer after 30 days immersion in PBS. The adhesion reduction of N-implanted/DLC composite layer was adverse for in vivo application in long term. So researcher should be cautious to use N implanted layer as an inter-layer for increasing CoCrMo alloy load carrying capacity in vivo environment.

Protein brownian rotation at the glass transition temperature of a freeze-concentrated buffer probed by superparamagnetic nanoparticles.

Science.gov (United States)

Eloi, J-C; Okuda, M; Jones, S E Ward; Schwarzacher, W

2013-06-18

For applications from food science to the freeze-thawing of proteins it is important to understand the often complex freezing behavior of solutions of biomolecules. Here we use a magnetic method to monitor the Brownian rotation of a quasi-spherical cage-shaped protein, apoferritin, approaching the glass transition Tg in a freeze-concentrated buffer (Tris-HCl). The protein incorporates a synthetic magnetic nanoparticle (Co-doped Fe3O4 (magnetite)). We use the magnetic signal from the nanoparticles to monitor the protein orientation. As T decreases toward Tg of the buffer solution the protein's rotational relaxation time increases exponentially, taking values in the range from a few seconds up to thousands of seconds, i.e., orders of magnitude greater than usually accessed, e.g., by NMR. The longest relaxation times measured correspond to estimated viscosities >2 MPa s. As well as being a means to study low-temperature, high-viscosity environments, our method provides evidence that, for the cooling protocol used, the following applies: 1), the concentration of the freeze-concentrated buffer at Tg is independent of its initial concentration; 2), little protein adsorption takes place at the interface between ice and buffer; and 3), the protein is free to rotate even at temperatures as low as 207 K. Copyright © 2013 Biophysical Society. Published by Elsevier Inc. All rights reserved.

Basics of base in hemodialysis solution: Dialysate buffer production, delivery and decontamination

Directory of Open Access Journals (Sweden)

N Desai

2015-01-01

Full Text Available Hemodialysis requires the use of high volumes of freshly prepared, clean dialysate to foster the removal of low molecular weight metabolites (i.e., urea and to correct the electrolyte and acid-base imbalance of chronic renal failure. Dialysate is produced by mixing clean, AAMI grade water with both an acid and base concentrate. This purpose of this report is to describe production, mixing and delivery of the buffer component of dialysate, and to also to address the cost, safety and feasibility of producing online bicarbonate. As endotoxin contaminated dialysate has been associated with the release of key mediators in acute and chronic inflammatory diseases associated with long-term hemodialysis therapy, aspects of disinfecting a bicarbonate delivery loop are also addressed.

Nature of Y1Ba2Cu3O7 nucleation centers on ceria buffers

International Nuclear Information System (INIS)

Solovyov, Vyacheslav F; Li Qiang; Qing Jie; Zhou Juan; Develos-Bagarinao, Katherine

2010-01-01

The purpose of this study is to enhance properties of the second-generation wires by increasing the density of Y 1 Ba 2 Cu 3 O 7 (YBCO) nucleation centers on the surface of the ceria buffer. To identify the nature of the nucleation centers, we compare nucleation kinetics and performance of YBCO layers deposited by the metal-organic process on a standard RABiTS tape to YBCO on ceria buffers with well-controlled structure and surface morphology. The structure of the YBCO layer at the early stage of nucleation and growth is determined by high-flux synchrotron x-ray diffraction. It is shown that the best buffers exhibit high YBCO nucleation rates and produce YBCO nuclei with the least cation disorder. The high YBCO nucleation rate is associated with a high density of threading dislocation outcrops. A strategy for buffer optimization is identified.

Buffer protection in the installation phase

International Nuclear Information System (INIS)

Wimelius, Hans; Pusch, Roland

2008-12-01

The research and development of the design and construction of the SKB's repository for final disposal of spent reactor fuel is conducted along several paths ('lines'). Issues concerning the bedrock are dealt with in the 'rock line' and those related to buffer and backfill in deposition holes and tunnels are considered in the 'buffer line' and 'backfill line', respectively. These lines also deal with sub-activities that are coupled to several other lines. One of them includes development of techniques for protecting buffer blocks from moisture and water in the installation phase. Techniques and methods for placement and removal of the 'buffer protection sheet' are dealt with in the 'buffer line'. The removal is, however, considered as being part of the backfilling sequence. Since the performance of the sheet is of fundamental importance to the placement and function of the buffer it deserves particular attention. Thus, the removal of the rubber sheet that serves to protect the buffer blocks in the installation phase may be difficult and can cause significant problems that may require retrieval of already placed canister, buffer and backfill. These matters are in focus in the present report. Arrangements for protecting already placed buffer blocks from moist air and water have been tested in earlier large-scale experiments, i.e. the Prototype Repository project at Aespoe but the experience from them has called for more effective protection of the clay blocks as described in the present report. Focus is on the construction of foundation components at the bottom of the deposition holes required for establishing a tight seal between rock and buffer blocks, and on the protection sheet and arrangements for limiting water pressure on it. Special attention is paid to the drainage of the space between rock and protection sheet that is necessary for avoiding failure of the sheet and to systems for achieving this and for providing alarm signals if the allowed pressure is

Corrosion Effects on the Fatigue Crack Propagation of Giga-Grade Steel and its Heat Affected Zone in pH Buffer Solutions for Automotive Application

Science.gov (United States)

Lee, H. S.

2018-03-01

Corrosion fatigue crack propagation test was conducted of giga-grade steel and its heat affected zone in pH buffer solutions, and the results were compared with model predictions. Pure corrosion effect on fatigue crack propagation, particularly, in corrosive environment was evaluated by means of the modified Forman equation. As shown in results, the average corrosion rate determined from the ratio of pure corrosion induced crack length to entire crack length under a cycle load were 0.11 and 0.37 for base metal and heat affected zone, respectively, with load ratio of 0.5, frequency of 0.5 and pH 10.0 environment. These results demonstrate new interpretation methodology for corrosion fatigue crack propagation enabling the pure corrosion effects on the behavior to be determined.

Photo-degradation behaviour of roseoflavin in some aqueous solutions

International Nuclear Information System (INIS)

Tyagi, A.; Penzkofer, A.; Mathes, T.; Hegemann, P.

2010-01-01

An absorption and emission spectroscopic characterization of roseoflavin (8-dimethylamino-8-demethyl-riboflavin, RoF) in aqueous solutions was carried out. The studies were concentrated on roseoflavin in pH 8 phosphate buffer. Absorption cross-section spectra, fluorescence excitation spectra, fluorescence quantum distributions, fluorescence quantum yields and fluorescence lifetimes were determined. The fluorescence of RoF is quenched by photo-induced intra-molecular charge-transfer at room temperature. The photo-degradation of RoF in un-buffered water, in Tris-HCl buffer, and in phosphate buffer was studied. Phosphate buffer and to a smaller extent Tris buffer catalyse the RoF photo-degradation. Photo-excitation of the primary photoproduct, 8-methylamino-riboflavin (8-MNH-RF), enhanced the RoF degradation by triplet 8-MNH-RF - singlet RoF excitation transfer with subsequent triplet-state RoF degradation.

Photo-degradation behaviour of roseoflavin in some aqueous solutions

Science.gov (United States)

Tyagi, A.; Penzkofer, A.; Mathes, T.; Hegemann, P.

2010-03-01

An absorption and emission spectroscopic characterization of roseoflavin (8-dimethylamino-8-demethyl-riboflavin, RoF) in aqueous solutions was carried out. The studies were concentrated on roseoflavin in pH 8 phosphate buffer. Absorption cross-section spectra, fluorescence excitation spectra, fluorescence quantum distributions, fluorescence quantum yields and fluorescence lifetimes were determined. The fluorescence of RoF is quenched by photo-induced intra-molecular charge-transfer at room temperature. The photo-degradation of RoF in un-buffered water, in Tris-HCl buffer, and in phosphate buffer was studied. Phosphate buffer and to a smaller extent Tris buffer catalyse the RoF photo-degradation. Photo-excitation of the primary photoproduct, 8-methylamino-riboflavin (8-MNH-RF), enhanced the RoF degradation by triplet 8-MNH-RF - singlet RoF excitation transfer with subsequent triplet-state RoF degradation.

Photo-degradation behaviour of roseoflavin in some aqueous solutions

Energy Technology Data Exchange (ETDEWEB)

Tyagi, A. [Institut II - Experimentelle und Angewandte Physik, Universitaet Regensburg, Universitaetsstrasse 31, D-93053 Regensburg (Germany); Penzkofer, A., E-mail: alfons.penzkofer@physik.uni-regensburg.de [Institut II - Experimentelle und Angewandte Physik, Universitaet Regensburg, Universitaetsstrasse 31, D-93053 Regensburg (Germany); Mathes, T.; Hegemann, P. [Institut fuer Biologie/Experimentelle Biophysik, Humboldt Universitaet zu Berlin, Invalidenstrasse 42, D-10115 Berlin (Germany)

2010-03-24

An absorption and emission spectroscopic characterization of roseoflavin (8-dimethylamino-8-demethyl-riboflavin, RoF) in aqueous solutions was carried out. The studies were concentrated on roseoflavin in pH 8 phosphate buffer. Absorption cross-section spectra, fluorescence excitation spectra, fluorescence quantum distributions, fluorescence quantum yields and fluorescence lifetimes were determined. The fluorescence of RoF is quenched by photo-induced intra-molecular charge-transfer at room temperature. The photo-degradation of RoF in un-buffered water, in Tris-HCl buffer, and in phosphate buffer was studied. Phosphate buffer and to a smaller extent Tris buffer catalyse the RoF photo-degradation. Photo-excitation of the primary photoproduct, 8-methylamino-riboflavin (8-MNH-RF), enhanced the RoF degradation by triplet 8-MNH-RF - singlet RoF excitation transfer with subsequent triplet-state RoF degradation.

Biochar contribution to soil pH buffer capacity

Science.gov (United States)

Tonutare, Tonu; Krebstein, Kadri; Utso, Maarius; Rodima, Ako; Kolli, Raimo; Shanskiy, Merrit

2014-05-01

Biochar as ecologically clean and stable form of carbon has complex of physical and chemical properties which make it a potentially powerful soil amendment (Mutezo, 2013). Therefore during the last decade the biochar application as soil amendment has been a matter for a great number of investigations. For the ecological viewpoint the trend of decreasing of soil organic matter in European agricultural land is a major problem. Society is faced with the task to find possibilities to stabilize or increase soil organic matter content in soil and quality. The availability of different functional groups (e.g. carboxylic, phenolic, acidic, alcoholic, amine, amide) allows soil organic matter to buffer over a wide range of soil pH values (Krull et al. 2004). Therefore the loss of soil organic matter also reduces cation exchange capacity resulting in lower nutrient retention (Kimetu et al. 2008). Biochar can retain elements in soil directly through the negative charge that develops on its surfaces, and this negative charge can buffer acidity in the soil. There are lack of investigations about the effect of biochar to soil pH buffering properties, The aim of our investigation was to investigate the changes in soil pH buffer capacity in a result of addition of carbonizated material to temperate region soils. In the experiment different kind of softwood biochars, activated carbon and different soil types with various organic matter and pH were used. The study soils were Albeluvisols, Leptosols, Cambisols, Regosols and Histosols . In the experiment the series of the soil: biochar mixtures with the biochar content 0 to 100% were used. The times of equiliberation between solid and liquid phase were from 1 to 168 hours. The suspension of soil: biochar mixtures was titrated with HCl solution. The titration curves were established and pH buffer capacities were calculated for the pH interval from 3.0 to 10.0. The results demonstrate the dependence of pH buffer capacity from soil type

The SVT Hit Buffer

International Nuclear Information System (INIS)

Belforte, S.; Dell'Orso, M.; Donati, S.

1996-01-01

The Hit Buffer is part of the Silicon Vertex Tracker, a trigger processor dedicated to the reconstruction of particle trajectories in the Silicon Vertex Detector and the Central Tracking Chamber of the Collider Detector at Fermilab. The Hit Buffer is a high speed data-traffic node, where thousands of words are received in arbitrary order and simultaneously organized in an internal structured data base, to be later promptly retrieved and delivered in response to specific requests. The Hit Buffer is capable of processing data at a rate of 25 MHz, thanks to the use of special fast devices like Cache-Tag RAMs and high performance Erasable Programmable Logic Devices from the XILINX XC7300 family

Study on the reduction and hysteresis effect of soil nitrogen pollution by Alfalfa in channel buffer bank

Science.gov (United States)

Chi, Yixia; Xue, Lianqing; Zhang, Zhanyu; Li, Dongying

2018-01-01

Based on the simulation experiments of solute transport in channel buffer bank and pot experiments, this study analyzed the transport of nitrogen pollution from farmland drains along the South-North Water Transfer east route project; and compared the nitrogen transport rule and purification effect of alfalfa in channel buffer bank soil under situations of bare land and alfalfa mulching. The results showed that: (1) soil nitrogen content decreased gradually with the width increase of channel buffer bank by the soil adsorption and decomposition; (2) the migration rates of nitrogen were 0.06 g·kg-1 by the alfalfa mulching; (3) the removed rates of nitrogen from the soil were 0.088 g·kg-1 by cutting alfalfa; (4) the residual nitrogen of soil with alfalfa was 10% of the bare land. Alfalfa in channel buffer bank had obvious reduction and hysteresis effect to soil nitrogen pollution.

Transmission investment problems in Europe: Going beyond standard solutions

International Nuclear Information System (INIS)

Buijs, Patrik; Bekaert, David; Cole, Stijn; Van Hertem, Dirk; Belmans, Ronnie

2011-01-01

The European transmission grid is facing an investment challenge. There is a strong call for more transmission capacity. At the same time, the investment climate is fierce and troubled by public opposition, a complex regulatory framework, etc. Many transmission capacity expansion projects are delayed or canceled. In this paper different technology options suitable for increasing transmission capacity are discussed. The aim is to provide policy-makers with information on technologies without going too much into technical details. The focus is on opportunities and limitations to implement various technological alternatives in practice, including technical solutions that go beyond constructing new connection lines. The criteria used in this technology assessment are based on the obstacles reported in the European Priority Interconnection Plan. This ensures a realistic approach based on problems encountered in real projects. Although AC overhead lines (OHL) will remain the standard solution for grid expansion, it is argued that different technology options can overcome many obstacles that OHL face. Additionally, it is illustrated that the higher investment costs for some solutions can be offset with an increased benefit, e.g. by accomplishing investments with smaller delays due to fewer obstacles encountered. - Research highlights: → Assessment of real problems encountered in transmission investments. → Comparison of transmission technologies. → Techno-economic evaluation of transmission technologies.

Electrocatalytic hydrogen evolution under densely buffered neutral pH conditions

KAUST Repository

Shinagawa, Tatsuya

2015-08-18

Under buffered neutral pH conditions, solute concentrations drastically influence the hydrogen evolution reaction (HER). The iR-free HER performance as a function of solute concentration was found to exhibit a volcano-shaped trend in sodium phosphate solution at pH 5, with the maximum occurring at 2 M. A detailed microkinetic model that includes calculated activity coefficients, solution resistance, and mass-transport parameters accurately describes the measured values, clarifying that the overall HER performance is predominantly governed by mass-transport of slow phosphate ions (weak acid). In the HER at the optimum concentration of approximately 2 M sodium phosphate at pH 5, our theoretical model predicts that the concentration overpotential accounts for more than half of the required overpotential. The substantial concentration overpotential would originate from the electrolyte property, suggesting that the proper electrolyte engineering will result in an improved apparent HER performances. The significance of concentration overpotential shown in the study is critical in the advancement of electrocatalysis, biocatalysis, and photocatalysis.

Electrocatalytic hydrogen evolution under densely buffered neutral pH conditions

KAUST Repository

Shinagawa, Tatsuya; Takanabe, Kazuhiro

2015-01-01

Under buffered neutral pH conditions, solute concentrations drastically influence the hydrogen evolution reaction (HER). The iR-free HER performance as a function of solute concentration was found to exhibit a volcano-shaped trend in sodium phosphate solution at pH 5, with the maximum occurring at 2 M. A detailed microkinetic model that includes calculated activity coefficients, solution resistance, and mass-transport parameters accurately describes the measured values, clarifying that the overall HER performance is predominantly governed by mass-transport of slow phosphate ions (weak acid). In the HER at the optimum concentration of approximately 2 M sodium phosphate at pH 5, our theoretical model predicts that the concentration overpotential accounts for more than half of the required overpotential. The substantial concentration overpotential would originate from the electrolyte property, suggesting that the proper electrolyte engineering will result in an improved apparent HER performances. The significance of concentration overpotential shown in the study is critical in the advancement of electrocatalysis, biocatalysis, and photocatalysis.

Low noise buffer amplifiers and buffered phase comparators for precise time and frequency measurement and distribution

Science.gov (United States)

Eichinger, R. A.; Dachel, P.; Miller, W. H.; Ingold, J. S.

1982-01-01

Extremely low noise, high performance, wideband buffer amplifiers and buffered phase comparators were developed. These buffer amplifiers are designed to distribute reference frequencies from 30 KHz to 45 MHz from a hydrogen maser without degrading the hydrogen maser's performance. The buffered phase comparators are designed to intercompare the phase of state of the art hydrogen masers without adding any significant measurement system noise. These devices have a 27 femtosecond phase stability floor and are stable to better than one picosecond for long periods of time. Their temperature coefficient is less than one picosecond per degree C, and they have shown virtually no voltage coefficients.

Synthesis, electrochemical, spectrophotometric and potentiometric studies of two azo-compounds derived from 4-amino-2-methylquinoline in ethanolic-aqueous buffered solutions

Energy Technology Data Exchange (ETDEWEB)

El-Attar, Mona A.; Ghoneim, Mohamed M. [Analytical Chemistry Research Unit, Chemistry Department, Tanta University (Egypt); Ismail, Iqbal M., E-mail: maema.2011@yahoo.com [Chemistry Department, Faculty of Science, King Abdul Aziz University, Jeddah (Saudi Arabia)

2012-08-15

Two azo-compounds, 2-methyl-4-(5-amino-2-hydroxy-phenylazo)-quinoline (2) and 2-methyl-4-(2-hydroxy-5-nitrophenylazo)-quinoline, derived from 4-amino-2-methylquinoline were synthesized. Their chemical structures were characterized and confirmed by means of elemental chemical analysis, infrared (IR) spectroscopy, {sup 1}H nuclear magnetic resonance (NMR) and mass spectrometry (MS). The electrochemical behavior of the starting compound (4-amino-2-methylquinoline) and of the two synthesized azo-derivatives was studied at the mercury electrode in the B-R universal buffer at various pH values (2-11.5) containing 40% (v/v) ethanol using dc-polarography, cyclic voltammetry and controlled-potential coulometry. Their electrode reaction pathways were elucidated and discussed. The dissociation constants (pKa) of the examined compounds, stability constants and stoichiometry of their complexes in solution with some transition metal ions (Co(II), Ni(II), Cu(II), La(III) and UO{sup 2+}{sub 2}) were determined. (author)

Preparation and certification of solutions of perdeuterated polycyclic aromatic compounds intended for use as surrogate internal standards

International Nuclear Information System (INIS)

Quilliam, M.A.; Hardstaff, W.R.; Anacleto, J.F.; LeBlanc, M.D.; Stergiopoulos, V.; Dick, K.L.; Bowser, M.T.; Curtis, J.M.; Embree, D.J.; Sim, P.G.; Boyd, R.K.

1994-01-01

Two standard solutions of deuterated polycyclic aromatic compounds (PACs) have been prepared for use as surrogate internal standards. Solution DPAC-1 contains 21 deuterated PACs, and is intended for use with mass spectrometric (MS) detection. Most of the difficulties in certifying concentrations in DPAC-1 arose from the fact that none of the individual compounds was 100% deuterated, so that effects of mass spectrometric fragmentation are convoluted with those of isotopic distributions. The best methods are discussed for using such internal standards so as to minimize these problems, together with those arising from kinetic isotope effects. Solution DPAC-2 contains 6 deuterated PACs, and is primarily intended for use with reversed-phase high-performance liquid chromatography (HPLC) with fluorescence detection (FLD, dural programmed wavelength mode), in which the signals for analyte and internal standard are separated chromatographically rather than via the detector. Full details of the preparation of these solutions are described. In addition, examples of their use in the analysis of a certified coal-tar extract (NIST SRM 1597) are described briefly. In one example a novel HPLC-MS technique was employed, and in the other the HPLC-FLD technique was used. (orig.)

Preparation of SmBiO{sub 3} buffer layer on YSZ substrate by an improved chemical solution deposition route

Energy Technology Data Exchange (ETDEWEB)

Zhu, Xiaolei [Key Laboratory of Advanced Technologies of Materials (Ministry of Education of China), Superconductivity and New Energy R& D Center, Mail Stop 165#, Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); Pu, Minghua, E-mail: mhpu@home.swjtu.edu.cn [Key Laboratory of Advanced Technologies of Materials (Ministry of Education of China), Superconductivity and New Energy R& D Center, Mail Stop 165#, Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); Zhao, Yong [Key Laboratory of Advanced Technologies of Materials (Ministry of Education of China), Superconductivity and New Energy R& D Center, Mail Stop 165#, Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); School of Materials Science and Engineering, University of New South Wale, Sydney, NSW 2052 (Australia)

2016-12-15

Highlights: • The proper conditions for SBO growth are 794 °C for 60 min in flowing Ar gas, the temperature of epitaxial growth is relatively low. • The total time by SSD technique for organic solvent removing, salts decomposition and layer growth is not up to 2 h, which are much less than that needed for traditional CSD of over 10 h. • SBO layer on YSZ prepared by SSD technique are suitable for the growth of YBCO, The results may be the usable reference for continuous preparation of SBO buffer layer on IBAD-YSZ/Ni-based alloy tapes. - Abstract: A quick route for chemical solution deposition (CSD) has been developed to prepare SmBiO{sub 3} (SBO) layers on yttria stabilized zirconia (YSZ) substrates rapidly by using of solid state decomposition (SSD) technique. The proper conditions for volatilization of lactic acid, which as solvent in precursor coated layer, and SBO growth are 115°C for 30 min and 794°C for 60 min in flowing Ar gas. The coated layers are amorphous structure of mixture oxides and quasi-crystal structure of SBO before and after growth, respectively. The total time by this quick CSD route for organic solvent volatilization, salts decomposed and layer growth is not up to 2 h, which are much less than that needed for traditional CSD of over 10 h. SBO layer is directly epitaxial growth on YSZ substrate without any lattice rotation. SBO layer prepared by this quick route as well as that by traditional route are suitable for the growth of YBCO. The superconducting transition temperature and critical current density of the coated YBCO layer on SBO/YSZ obtained by this quick route are up to 90 K and 1.66 MA/cm{sup 2}. These results may be the usable reference for continuous preparation of SBO buffer layer on IBAD-YSZ/Ni-based alloy tapes.

Buffered Communication Analysis in Distributed Multiparty Sessions

Science.gov (United States)

Deniélou, Pierre-Malo; Yoshida, Nobuko

Many communication-centred systems today rely on asynchronous messaging among distributed peers to make efficient use of parallel execution and resource access. With such asynchrony, the communication buffers can happen to grow inconsiderately over time. This paper proposes a static verification methodology based on multiparty session types which can efficiently compute the upper bounds on buffer sizes. Our analysis relies on a uniform causality audit of the entire collaboration pattern - an examination that is not always possible from each end-point type. We extend this method to design algorithms that allocate communication channels in order to optimise the memory requirements of session executions. From these analyses, we propose two refinements methods which respect buffer bounds: a global protocol refinement that automatically inserts confirmation messages to guarantee stipulated buffer sizes and a local protocol refinement to optimise asynchronous messaging without buffer overflow. Finally our work is applied to overcome a buffer overflow problem of the multi-buffering algorithm.

Fast scalar data buffering interface in Linux 2.6 kernel

International Nuclear Information System (INIS)

Homs, A.

2012-01-01

Key instrumentation devices like counter/timers, analog-to-digital converters and encoders provide scalar data input. Many of them allow fast acquisitions, but do not provide hardware triggering or buffering mechanisms. A Linux 2.4 kernel driver called Hook was developed at the ESRF as a generic software-triggered buffering interface. This work presents the portage of the ESRF Hook interface to the Linux 2.6 kernel. The interface distinguishes 2 independent functional groups: trigger event generators and data channels. Devices in the first group create software events, like hardware interrupts generated by timers or external signals. On each event, one or more device channels on the second group are read and stored in kernel buffers. The event generators and data channels to be read are fully configurable before each sequence. Designed for fast acquisitions, the Hook implementation is well adapted to multi-CPU systems, where the interrupt latency is notably reduced. On heavily loaded dual-core PCs running standard (non real time) Linux, data can be taken at 1 KHz without losing events. Additional features include full integration into the /sys virtual file-system and hot-plug devices support. (author)

Peak distortion in the column liquid chromatographic determination of omeprazole dissolved in borax buffer.

Science.gov (United States)

Arvidsson, T; Collijn, E; Tivert, A M; Rosén, L

1991-11-22

Injection of a sample containing omeprazole dissolved in borax buffer (pH 9.2) into a reversed-phase liquid chromatographic system consisting of a mixture of acetonitrile and phosphate buffer (pH 7.6) as the mobile phase and a C18 surface-modified silica as the solid phase resulted under special conditions in split peaks of omeprazole. The degree of peak split and the retention time of omeprazole varied with the concentration of borax in the sample solution and the ionic strength of the mobile phase buffer as well as with the column used. Borax is eluted from the column in a broad zone starting from the void volume of the column. The retention is probably due to the presence of polyborate ions. The size of the zone varies with the concentration of borax in the sample injected. In the borax zone the pH is increased compared with the pH of the mobile phase, and when omeprazole (a weak acid) is co-eluting in the borax zone its retention is affected. In the front part and in the back part of the borax zone, pH gradients are formed, and these gradients can induce the peak splitting. When the dissolving medium is changed to a phosphate buffer or an ammonium buffer at pH 9 no peak distortion of omeprazole is observed.

Buffer protection in the installation phase

Energy Technology Data Exchange (ETDEWEB)

Wimelius, Hans (Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden)); Pusch, Roland (Geodevelopment International AB, Lund (Sweden))

2008-12-15

The research and development of the design and construction of the SKB's repository for final disposal of spent reactor fuel is conducted along several paths ('lines'). Issues concerning the bedrock are dealt with in the 'rock line' and those related to buffer and backfill in deposition holes and tunnels are considered in the 'buffer line' and 'backfill line', respectively. These lines also deal with sub-activities that are coupled to several other lines. One of them includes development of techniques for protecting buffer blocks from moisture and water in the installation phase. Techniques and methods for placement and removal of the 'buffer protection sheet' are dealt with in the 'buffer line'. The removal is, however, considered as being part of the backfilling sequence. Since the performance of the sheet is of fundamental importance to the placement and function of the buffer it deserves particular attention. Thus, the removal of the rubber sheet that serves to protect the buffer blocks in the installation phase may be difficult and can cause significant problems that may require retrieval of already placed canister, buffer and backfill. These matters are in focus in the present report. Arrangements for protecting already placed buffer blocks from moist air and water have been tested in earlier large-scale experiments, i.e. the Prototype Repository project at Aespoe but the experience from them has called for more effective protection of the clay blocks as described in the present report. Focus is on the construction of foundation components at the bottom of the deposition holes required for establishing a tight seal between rock and buffer blocks, and on the protection sheet and arrangements for limiting water pressure on it. Special attention is paid to the drainage of the space between rock and protection sheet that is necessary for avoiding failure of the sheet and to systems for achieving

An determination of man-made γ-emitting radionuclides in coal fly ash and standard solution

International Nuclear Information System (INIS)

Xu Cuihua; Zhou Qiang

2004-01-01

We participated an international comparison on the determination of man-made γ-emitting radionuclides in coal fly ash and in standard solution organized by the Analytical Quality Control Service of the IAEA in 2002. The sample was dispensed in 100.0 ± 0.1 g aliquots in plastic container and was spiked with known amounts of certified standard γ-emitting radionuclides 54 Mn, 57 Co, 60 Co, 65 Zn, 88 Y, 134 Cs, 137 Cs and 241 Am. The determination of the anthropogenic )γ-emitting radionuclides in the test samples was carried out with an ORTEC gamma-ray spectrometry system coupled with a HPGe detector with resolution of 1.75 keV and relative efficiency of 55% for 137 Cs, located in a 10 cm thick lead container. The energy and efficiency calibration were with home-made volume calibration sources containing some of the radionuclides to be analyzed. The analysis procedure is described elsewhere. Table 1 lists the results of the determination and the comparisons with IAEA reference data and evaluation. Overall our results are agreeable in ±8.6% with the IAEA reference data, except for 60 Co. The differences for 60 Co was -10.8%. It may be caused by the 60 Co calibration source made with residual of quiet old standard solution. The difference for 241 Am is due to self-absorption in the fly ash sample. This bias was small for the solution sample. For standard solution sample, the results are agreeable within ±3.7% for all radionuclides except for 60 Co, being 12%. (authors)

Comparison of Ring-Buffer-Based Packet Capture Solutions

Energy Technology Data Exchange (ETDEWEB)

Barker, Steven Andrew [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

2015-10-01

Traditional packet-capture solutions using commodity hardware incur a large amount of overhead as packets are copied multiple times by the operating system. This overhead slows sensor systems to a point where they are unable to keep up with high bandwidth traffic, resulting in dropped packets. Incomplete packet capture files hinder network monitoring and incident response efforts. While costly commercial hardware exists to capture high bandwidth traffic, several software-based approaches exist to improve packet capture performance using commodity hardware.

SODR Memory Control Buffer Control ASIC

Science.gov (United States)

Hodson, Robert F.

1994-01-01

The Spacecraft Optical Disk Recorder (SODR) is a state of the art mass storage system for future NASA missions requiring high transmission rates and a large capacity storage system. This report covers the design and development of an SODR memory buffer control applications specific integrated circuit (ASIC). The memory buffer control ASIC has two primary functions: (1) buffering data to prevent loss of data during disk access times, (2) converting data formats from a high performance parallel interface format to a small computer systems interface format. Ten 144 p in, 50 MHz CMOS ASIC's were designed, fabricated and tested to implement the memory buffer control function.

OPTIMISATION OF BUFFER SIZE FOR ENHANCING QOS OF VIDEO TRAFFIC USING CROSS LAYERED HYBRID TRANSPORT LAYER PROTOCOL APPROACH

Directory of Open Access Journals (Sweden)

S. Matilda

2011-03-01

Full Text Available Video streaming is gaining importance, with the wide popularity of multimedia rich applications in the Internet. Video streams are delay sensitive and require seamless flow for continuous visualization. Properly designed buffers offer a solution to queuing delay. The diagonally opposite QoS metrics associated with video traffic poses an optimization problem, in the design of buffers. This paper is a continuation of our previous work [1] and deals with the design of buffers. It aims at finding the optimum buffer size for enhancing QoS offered to video traffic. Network-centric QoS provisioning approach, along with hybrid transport layer protocol approach is adopted, to arrive at an optimum size which is independent of RTT. In this combinational approach, buffers of routers and end devices are designed to satisfy the various QoS parameters at the transport layer. OPNET Modeler is used to simulate environments for testing the design. Based on the results of simulation it is evident that the hybrid transport layer protocol approach is best suited for transmitting video traffic as it supports the economical design.

Standard partial molar heat capacities and enthalpies of formation of aqueous aluminate under hydrothermal conditions from integral heat of solution measurements

International Nuclear Information System (INIS)

Coulier, Yohann; Tremaine, Peter R.

2014-01-01

Highlights: • Heats of solution of NaAlO 2 (s) were measured at five temperatures up to 250 °C. • Standard molar enthalpies of solution were determined from the measured heats of solution. • Standard molar enthalpies of solution were correlated with the density model. • The density model allows us to determine the standard molar heat capacities of reaction. - Abstract: Heats of solution of sodium aluminum oxide, NaAlO 2 (s), were measured in aqueous sodium hydroxide solutions using a Tian–Calvet heat-flow calorimeter (Setaram, Model C80) with high pressure “batch cells” made of hastelloy C-276, at five temperatures from (373.15 to 523.15) K, steam saturation pressure, and concentrations from (0.02 to 0.09) mol · kg −1 . Standard molar enthalpies of solution, Δ soln H ∘ , and relative standard molar enthalpies, [H ∘ (T) − H ∘ (298.15 K)], of NaAl(OH) 4 (aq) were determined from the measured heats of solution. The results were fitted with the “density” model. The temperature dependence of Δ soln H ∘ from the model yielded the standard molar heat capacities of reaction, Δ soln C p ∘ , from which standard partial molar heat capacities for aqueous aluminate, C p ∘ [A1(OH) 4 − ,aq], were calculated. Standard partial molar enthalpies of formation, Δ f H ∘ , and entropies, S ∘ , of A1(OH) 4 − (aq) were also determined. The values for C p ∘ [A1(OH) 4 − ,aq] agree with literature data determined up to T = 413 K from enthalpy of solution and heat capacity measurements to within the combined experimental uncertainties. They are consistent with differential heat capacity measurements up to T = 573 K from Schrödle et al. (2010) [29] using the same calorimeter, but this method has the advantage that measurements could be made at much lower concentrations in the presence of an excess concentration of ligand. To our knowledge, these are the first standard partial molar heat capacities measured under hydrothermal conditions by the

Dynamic mechanical properties of buffer material

International Nuclear Information System (INIS)

Takaji, Kazuhiko; Taniguchi, Wataru

1999-11-01

The buffer material is expected to maintain its low water permeability, self-sealing properties, radionuclides adsorption and retardation properties, thermal conductivity, chemical buffering properties, overpack supporting properties, stress buffering properties, etc. over a long period of time. Natural clay is mentioned as a material that can relatively satisfy above. Among the kinds of natural clay, bentonite when compacted is superior because (i) it has exceptionally low water permeability and properties to control the movement of water in buffer, (ii) it fills void spaces in the buffer and fractures in the host rock as it swells upon water uptake, (iii) it has the ability to exchange cations and to adsorb cationic radioelements. In order to confirm these functions for the purpose of safety assessment, it is necessary to evaluate buffer properties through laboratory tests and engineering-scale tests, and to make assessments based on the ranges in the data obtained. This report describes the procedures, test conditions, results and examinations on the buffer material of dynamic triaxial tests, measurement of elastic wave velocity and liquefaction tests that aim at getting hold of dynamic mechanical properties. We can get hold of dependency on the shearing strain of the shearing modulus and hysteresis damping constant, the application for the mechanical model etc. by dynamic triaxial tests, the acceptability of maximum shearing modulus obtained from dynamic triaxial tests etc. by measurement of elastic wave velocity and dynamic strength caused by cyclic stress etc. by liquefaction tests. (author)

HFB : A FASTBUS multi event double port buffer memory

International Nuclear Information System (INIS)

Cerrito, L.; Lebbolo, H.

1986-01-01

The authors describe here the FB double port buffer memory developed at the LPNHE of the University Paris VI. Its purposes are to make available same features useful in the High Energy environment, to reduce, for a given amount of memory, the dead time data collection in a large size (in term of read-out channels) High Energy experiment and to get a buffer of memory as cheap and reliable as possible. The FB protocol, on the crate and cable side, is exploited using the coupler on 4 PAL's developed by G.Fremont and E.Sanchis. The DATA-Space is divided in 4 independent smaller blocks in a way such that a block can be accessed from a port while a different block is accessed from the other port. The two ports are: A, the FB crate port and B, the FB cable port. The buffer works as a rotary FIFO, looping over the 4 blocks of memory, but allowing for any random access. A mechanism is implemented on the board in order to be able to link different modules placed everywhere. If there are m modules, the looping will be around m 4 memory blocks. A multi event function is implemented on the board. HFB is quiped of two NTA for the DATA-Space on the port ''A'', and a flag to choose between them, to allow for a FB spying of DATA during the DAS dead time. HFB is a buffer of memory which can be used at each stage of a DAS: Frontend, Intermediate (MEB) or final, being completely FB standard. The HFB was designed for the LEP data acquisition system

The role of preservation solution on acid-base regulation during machine perfusion of kidneys.

Science.gov (United States)

Baicu, Simona C; Taylor, Michael J; Brockbank, Kelvin G M

2006-01-01

To meet the current clinical organ demand, efficient preservation methods and solutions are needed to increase the number of viable kidneys for transplantation. In the present study, the influence of perfusion solution buffering strength on renal pH dynamics and regulation mechanisms during kidney ex vivo preservation was determined. Porcine kidneys were hypothermically machine perfused for 72 h with either Unisol-UHK or Belzer-Machine Perfusion solution, Belzer-MP solution. Renal perfusate samples were periodically collected and biochemically analyzed. The UHK solution, a Hepes-based solution (35 mM), provided a more efficient control of renal pH that, in turn, resulted in minor changes in the perfusate pH relative to baseline, in response to tissue CO2 and HCO3- production. In the perfusate of Belzer-MP kidney group a wider range of pH values were recorded and a pronounced pH reduction was seen in response to significant rises in pCO2 and HCO3- concentrations. The Belzer-MP solution, containing phosphate (25 mM) as its main buffer, and only 10 mM Hepes, had a greater buffering requirement to attenuate larger pH changes.

Analysis of two production inventory systems with buffer, retrials and different production rates

Science.gov (United States)

Jose, K. P.; Nair, Salini S.

2017-09-01

This paper considers the comparison of two ( {s,S} ) production inventory systems with retrials of unsatisfied customers. The time for producing and adding each item to the inventory is exponentially distributed with rate β. However, a production rate α β higher than β is used at the beginning of the production. The higher production rate will reduce customers' loss when inventory level approaches zero. The demand from customers is according to a Poisson process. Service times are exponentially distributed. Upon arrival, the customers enter into a buffer of finite capacity. An arriving customer, who finds the buffer full, moves to an orbit. They can retry from there and inter-retrial times are exponentially distributed. The two models differ in the capacity of the buffer. The aim is to find the minimum value of total cost by varying different parameters and compare the efficiency of the models. The optimum value of α corresponding to minimum total cost is an important evaluation. Matrix analytic method is used to find an algorithmic solution to the problem. We also provide several numerical or graphical illustrations.

The buffer/container experiment: results, synthesis, issues

International Nuclear Information System (INIS)

Graham, J.; Chandler, N.A.; Dixon, D.A.; Roach, P.J.; To, T.; Wan, A.W.L.

1997-12-01

A large in-ground experiment has examined how heat affects the performance of the dense sand bentonite 'buffer' that has been proposed for use in the Canadian Nuclear Fuel Waste Management Program. The experiment was performed by Atomic Energy of Canada Limited at its Underground Research Laboratory, Lac du Bonnet, Manitoba between 1991 and 1994. The experiment placed a full-size heater representing a container of nuclear fuel waste in a 1.24-m diameter borehole filled with buffer below the floor of a room excavated at 240-m depth in granitic rock of the Canadian Shield. The buffer and surrounding rock were extensively instrumented for temperatures, total pressures, water pressures, suctions, and rock displacements. Power was provided to the heater for almost 900 days. The experiment showed that good rock conditions can be pre-selected, a borehole can be drilled, and buffer can be placed at controlled densities and water contents. The instrumentation generally worked well, and an extensive data base was successfully organized. Drying was observed in buffer close to the heater. This caused some desiccation cracking. However the cracks only extended approximately one third of the distance to the buffer-rock interface and did not form an advective pathway. Following sampling at the time of decommissioning, cracked samples of buffer were transported to the laboratory and given access to water. The hydraulic conductivities and swelling pressures of these resaturated samples were very similar to those of uncracked buffer. A good balance was achieved between the mass of water flowing into the experiment from the surrounding rock and the increased mass of water in the buffer. A good understanding was developed of the relationships between suctions, water contents, and total pressures in buffer near the buffer-rock interface. Comparisons between measurements and predictions of measured parameters show that a good understanding has been developed of the processes operating

The buffer/container experiment: results, synthesis, issues

Energy Technology Data Exchange (ETDEWEB)

Graham, J. [Univ. of Manitoba, Dept. of Civil Engineering, Winnipeg, MB (Canada); Chandler, N.A.; Dixon, D.A.; Roach, P.J.; To, T.; Wan, A.W.L

1997-12-01

A large in-ground experiment has examined how heat affects the performance of the dense sand bentonite 'buffer' that has been proposed for use in the Canadian Nuclear Fuel Waste Management Program. The experiment was performed by Atomic Energy of Canada Limited at its Underground Research Laboratory, Lac du Bonnet, Manitoba between 1991 and 1994. The experiment placed a full-size heater representing a container of nuclear fuel waste in a 1.24-m diameter borehole filled with buffer below the floor of a room excavated at 240-m depth in granitic rock of the Canadian Shield. The buffer and surrounding rock were extensively instrumented for temperatures, total pressures, water pressures, suctions, and rock displacements. Power was provided to the heater for almost 900 days. The experiment showed that good rock conditions can be pre-selected, a borehole can be drilled, and buffer can be placed at controlled densities and water contents. The instrumentation generally worked well, and an extensive data base was successfully organized. Drying was observed in buffer close to the heater. This caused some desiccation cracking. However the cracks only extended approximately one third of the distance to the buffer-rock interface and did not form an advective pathway. Following sampling at the time of decommissioning, cracked samples of buffer were transported to the laboratory and given access to water. The hydraulic conductivities and swelling pressures of these resaturated samples were very similar to those of uncracked buffer. A good balance was achieved between the mass of water flowing into the experiment from the surrounding rock and the increased mass of water in the buffer. A good understanding was developed of the relationships between suctions, water contents, and total pressures in buffer near the buffer-rock interface. Comparisons between measurements and predictions of measured parameters show that a good understanding has been developed of the processes

International comparison of observation-specific spatial buffers

DEFF Research Database (Denmark)

Frank, Lawrence D; Fox, Eric H; Ulmer, Jared M

2017-01-01

the relative differences in resulting explanatory power on self-reported physical activity outcomes. BEMs were developed in five countries using 'sausage,' 'detailed-trimmed,' and 'detailed,' network buffers at a distance of 1 km around participant household addresses (n = 5883). RESULTS: BEM values were...... significantly different (p trimmed buffer comparisons and 89% of sausage versus detailed network buffer comparisons. Results showed that BEM coefficients in physical activity models did not differ significantly across buffering methods, and in most cases BEM...

Multi-Buffer Simulations for Trace Language Inclusion

Directory of Open Access Journals (Sweden)

Milka Hutagalung

2016-09-01

Full Text Available We consider simulation games played between Spoiler and Duplicator on two Büchi automata in which the choices made by Spoiler can be buffered by Duplicator in several buffers before she executes them on her structure. We show that the simulation games are useful to approximate the inclusion of trace closures of languages accepted by finite-state automata, which is known to be undecidable. We study the decidability and complexity and show that the game with bounded buffers can be decided in polynomial time, whereas the game with one unbounded and one bounded buffer is highly undecidable. We also show some sufficient conditions on the automata for Duplicator to win the game (with unbounded buffers.

Impact of solute concentration on the electrocatalytic conversion of dissolved gases in buffered solutions

KAUST Repository

Shinagawa, Tatsuya; Takanabe, Kazuhiro

2015-01-01

. These alterations of the electrolyte properties associated with the solute concentration are universally applicable to other aqueous gas-related electrochemical reactions because the currents are purely determined by mass transfer of the dissolved gases. © 2015

THE BUFFER CAPACITY OF AIRWAY EPITHELIAL SECRETIONS

Directory of Open Access Journals (Sweden)

Dusik eKim

2014-06-01

Full Text Available The pH of airway epithelial secretions influences bacterial killing and mucus properties and is reduced by acidic pollutants, gastric reflux, and respiratory diseases such as cystic fibrosis (CF. The effect of acute acid loads depends on buffer capacity, however the buffering of airway secretions has not been well characterized. In this work we develop a method for titrating micro-scale (30 µl volumes and use it to study fluid secreted by the human airway epithelial cell line Calu-3, a widely used model for submucosal gland serous cells. Microtitration curves revealed that HCO3- is the major buffer. Peak buffer capacity (β increased from 17 to 28 mM/pH during forskolin stimulation, and was reduced by >50% in fluid secreted by cystic fibrosis transmembrane conductance regulator (CFTR-deficient Calu-3 monolayers, confirming an important role of CFTR in HCO3- secretion. Back-titration with NaOH revealed non-volatile buffer capacity due to proteins synthesized and released by the epithelial cells. Lysozyme and mucin concentrations were too low to buffer Calu-3 fluid significantly, however model titrations of porcine gastric mucins at concentrations near the sol-gel transition suggest that mucins may contribute to the buffer capacity of ASL in vivo. We conclude that CFTR-dependent HCO3- secretion and epithelially-derived proteins are the predominant buffers in Calu-3 secretions.

CZE separation of strawberry anthocyanins with acidic buffer and comparison with HPLC.

Science.gov (United States)

Comandini, Patrizia; Blanda, Giampaolo; Cardinali, Andrea; Cerretani, Lorenzo; Bendini, Alessandra; Caboni, Maria Fiorenza

2008-10-01

Anthocyanins, the major colourants of strawberries, are polar pigments that are positively charged at low pH. Herein, we have assessed a new analytical method for the separation of anthocyanins using CZE. Acidic buffer solutions (pH pigments in the cation flavylium form and achieve high molar absorptivity at 510 nm. These spectral properties enabled us to identify strawberry anthocyanins in a preliminary stage by detection in the visible range, although the method was optimised at 280 nm to obtain the best S/N. The effects of buffer composition highlighted the necessity of adding an organic modifier to the running buffer to obtain a suitable separation. The electrophoretic method permitted the separation of the three main anthocyanins of strawberry extracts, namely pelargonidin 3-glucoside (Pg-glu), pelargonidin 3-rutinoside and cyanidin 3-glucoside. The electrophoretic results, expressed as retention time and separation efficiency of the major anthocyanin (Pg-glu), were compared to those achieved in HPLC, the analytical technique traditionally used for the investigation of anthocyanins in vegetable matrix. The content of Pg-glu in strawberries (cv. Camarosa), calculated with HPCE and HPLC methods, resulted respectively in 11.41 mg/L and 11.37 mg/L.

Problems with multiple use of transfer buffer in protein electrophoretic transfer.

Science.gov (United States)

Dorri, Yaser; Kurien, Biji T; Scofield, R Hal

2010-04-01

Two-dimensional gel electrophoresis (2DE) and SDS-PAGE are the two most useful methods in protein separation. Proteins separated by 2DE or SDS-PAGE are usually transferred to membranes using a variety of methods, such as electrophoretic transfer, heat-mediated transfer, or nonelectrophoretic transfer, for specific protein detection and/or analysis. In a recent study, Pettegrew et al. claim to reuse transfer buffer containing methanol for at least five times for transferring proteins from SDS-PAGE to polyvinylidene difluoride. They add 150-200 ml fresh transfer solution each time for extended use as a result of loss of transfer buffer. Finally, they test efficiency of each protein transfer by chemiluminescence detection. Here, we comment on this report, as we believe this method is not accurate and useful for protein analysis, and it can cause background binding as well as inaccurate protein analysis.

Accurate determination of arsenic in arsenobetaine standard solutions of BCR-626 and NMIJ CRM 7901-a by neutron activation analysis coupled with internal standard method.

Science.gov (United States)

Miura, Tsutomu; Chiba, Koichi; Kuroiwa, Takayoshi; Narukawa, Tomohiro; Hioki, Akiharu; Matsue, Hideaki

2010-09-15

Neutron activation analysis (NAA) coupled with an internal standard method was applied for the determination of As in the certified reference material (CRM) of arsenobetaine (AB) standard solutions to verify their certified values. Gold was used as an internal standard to compensate for the difference of the neutron exposure in an irradiation capsule and to improve the sample-to-sample repeatability. Application of the internal standard method significantly improved linearity of the calibration curve up to 1 microg of As, too. The analytical reliability of the proposed method was evaluated by k(0)-standardization NAA. The analytical results of As in AB standard solutions of BCR-626 and NMIJ CRM 7901-a were (499+/-55)mgkg(-1) (k=2) and (10.16+/-0.15)mgkg(-1) (k=2), respectively. These values were found to be 15-20% higher than the certified values. The between-bottle variation of BCR-626 was much larger than the expanded uncertainty of the certified value, although that of NMIJ CRM 7901-a was almost negligible. Copyright (c) 2010 Elsevier B.V. All rights reserved.

Comparison of ophthalmic sponges and extraction buffers for quantifying cytokine profiles in tears using Luminex technology.

Science.gov (United States)

Inic-Kanada, Aleksandra; Nussbaumer, Andrea; Montanaro, Jacqueline; Belij, Sandra; Schlacher, Simone; Stein, Elisabeth; Bintner, Nora; Merio, Margarethe; Zlabinger, Gerhard J; Barisani-Asenbauer, Talin

2012-01-01

Evaluating cytokine profiles in tears could shed light on the pathogenesis of various ocular surface diseases. When collecting tears with the methods currently available, it is often not possible to avoid the tear reflex, which may give a different cytokine profile compared to basal tears. More importantly, tear collection with glass capillaries, the most widely used method for taking samples and the best method for avoiding tear reflex, is impractical for remote area field studies because it is tedious and time-consuming for health workers, who cannot collect tears from a large number of patients with this method in one day. Furthermore, this method is uncomfortable for anxious patients and children. Thus, tears are frequently collected using ophthalmic sponges. These sponges have the advantage that they are well tolerated by the patient, especially children, and enable standardization of the tear collection volume. The aim of this study was to compare various ophthalmic sponges and extraction buffers to optimize the tear collection method for field studies for subsequent quantification of cytokines in tears using the Luminex technology. Three ophthalmic sponges, Merocel, Pro-ophta, and Weck-Cel, were tested. Sponges were presoaked with 25 cytokines/chemokines of known concentrations and eluted with seven different extraction buffers (EX1-EX7). To assess possible interference in the assay from the sponges, two standard curves were prepared in parallel: 1) cytokines of known concentrations with the extraction buffers and 2) cytokines of known concentrations loaded onto the sponges with the extraction buffers. Subsequently, a clinical assessment of the chosen sponge-buffer combination was performed with tears collected from four healthy subjects using 1) aspiration and 2) sponges. To quantify cytokine/chemokine recovery and the concentration in the tears, a 25-plex Cytokine Panel and the Luminex xMap were used. This platform enables simultaneous measurement of

Comparison of ophthalmic sponges and extraction buffers for quantifying cytokine profiles in tears using Luminex technology

Science.gov (United States)

Inic-Kanada, Aleksandra; Nussbaumer, Andrea; Montanaro, Jacqueline; Belij, Sandra; Schlacher, Simone; Stein, Elisabeth; Bintner, Nora; Merio, Margarethe; Zlabinger, Gerhard J.

2012-01-01

Purpose Evaluating cytokine profiles in tears could shed light on the pathogenesis of various ocular surface diseases. When collecting tears with the methods currently available, it is often not possible to avoid the tear reflex, which may give a different cytokine profile compared to basal tears. More importantly, tear collection with glass capillaries, the most widely used method for taking samples and the best method for avoiding tear reflex, is impractical for remote area field studies because it is tedious and time-consuming for health workers, who cannot collect tears from a large number of patients with this method in one day. Furthermore, this method is uncomfortable for anxious patients and children. Thus, tears are frequently collected using ophthalmic sponges. These sponges have the advantage that they are well tolerated by the patient, especially children, and enable standardization of the tear collection volume. The aim of this study was to compare various ophthalmic sponges and extraction buffers to optimize the tear collection method for field studies for subsequent quantification of cytokines in tears using the Luminex technology. Methods Three ophthalmic sponges, Merocel, Pro-ophta, and Weck-Cel, were tested. Sponges were presoaked with 25 cytokines/chemokines of known concentrations and eluted with seven different extraction buffers (EX1–EX7). To assess possible interference in the assay from the sponges, two standard curves were prepared in parallel: 1) cytokines of known concentrations with the extraction buffers and 2) cytokines of known concentrations loaded onto the sponges with the extraction buffers. Subsequently, a clinical assessment of the chosen sponge-buffer combination was performed with tears collected from four healthy subjects using 1) aspiration and 2) sponges. To quantify cytokine/chemokine recovery and the concentration in the tears, a 25-plex Cytokine Panel and the Luminex xMap were used. This platform enables simultaneous

Magnetorheological elastomer and its application on impact buffer

International Nuclear Information System (INIS)

Fu, J; Yu, M; Zhu, L X; Dong, X M

2013-01-01

In this study, a new magnetorheological elastomer (MRE) based buffer is proposed and its vibration isolation performance is investigated. The MRE buffer with a compact structure is first designed in order to accomplish the maximization of the variable stiffness range. The working characteristics of the MRE buffer are then measured and the model of MRE is established. On the basis of the experimental data, the control model of the MRE buffer is also formulated. A two-degree-of-freedom dynamic model with an MRE buffer is then developed. An intelligent control strategy, human simulated intelligent control (HSIC), is proposed to reduce the impact during the drop crash. Finally, the proposed MRE buffer and controller are validated numerically and experimentally. The results show that the proposed MRE buffer and the control strategy can reduce the impact acceleration effectively.

Comparison of 2 Luminex-based Multiplexed Protein Assays for Quantifying Microglia Activation and Inflammatory Proteins

Science.gov (United States)

2016-04-01

responses. The kit also contains buffer solution , beads conjugated to antibodies, wash buffers, a positive control sample, and a standard agent...the standard solution provided with 2 of the kits (Rat Liver Injury Panel and Rat Cytokine–Chemokine) to generate the standard curve that allows for...are possibly the result of human error. Through a miscommunication , the initial sample concentration was below the recommended protein concentration

Variety and variability of bentonites as buffer materials in radioactive waste disposal

International Nuclear Information System (INIS)

Sato, Tsutomu

1994-01-01

Bentonite which is considered to be most promising as the buffer material in the formation disposal of high level radioactive waste is the clay having Montmorillonite of smectite group as the main component mineral. The clay of smectite group shows different properties, and its range of variability is wide. In this report, the clay minerals of smectite group and their variety are explained from the viewpoint of crystal chemistry, and the difference in expansion property, water recovery property and long period stability, which are expected for the buffer material in formation disposal, in various smectite clays is described. The trend of the investigation of the buffer materials and the importance of making their standard are referred to. In the formation disposal of high level radioactive waste, multiple barrier concept is investigated. The expectation for the development of intelligent materials is large. Bentonite established the position as one of the intelligent materials. The factors controlling the properties of clay are the compositions of clay minerals, nonclay minerals, organic substances, exchangeable cations and soluble salts and texture. (K.I.)

Providers and Patients Caught Between Standardization and Individualization: Individualized Standardization as a Solution Comment on "(Re) Making the Procrustean Bed? Standardization and Customization as Competing Logics in Healthcare".

Science.gov (United States)

Ansmann, Lena; Pfaff, Holger

2017-08-12

In their 2017 article, Mannion and Exworthy provide a thoughtful and theory-based analysis of two parallel trends in modern healthcare systems and their competing and conflicting logics: standardization and customization. This commentary further discusses the challenge of treatment decision-making in times of evidence-based medicine (EBM), shared decision-making and personalized medicine. From the perspective of systems theory, we propose the concept of individualized standardization as a solution to the problem. According to this concept, standardization is conceptualized as a guiding framework leaving room for individualization in the patient physician interaction. The theoretical background is the concept of context management according to systems theory. Moreover, the comment suggests multidisciplinary teams as a possible solution for the integration of standardization and individualization, using the example of multidisciplinary tumor conferences and highlighting its limitations. The comment also supports the authors' statement of the patient as co-producer and introduces the idea that the competing logics of standardization and individualization are a matter of perspective on macro, meso and micro levels. © 2018 The Author(s); Published by Kerman University of Medical Sciences. This is an open-access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

The thermodynamic-buffer enzymes.

Science.gov (United States)

Stucki, J W

1980-08-01

Oxidative phosphorylation operates at optimal efficiency if and only if the condition of conductance matching L33/L11 = square root 1-q2 is fulfilled. In this relation L11 is the phenomenological conductance of phosphorylation, L33 the phenomenological conductance of the load, i.e. the irreversible ATP-utilizing processes in the cell, and q the degree of coupling of oxidative phosphorylation driven by respiration. Since during short time intervals L11 and q are constant whereas L33 fluctuates in the cell, oxidative phosphorylation would only rarely operate at optimal efficiency due to violation of conductance matching. This paper demonstrates that the reversible ATP-utilizing reaction catalyzed by adenylate kinase can effectively compensate deviations from conductance matching in the presence of a fluctuating L33 and hence allows oxidative phosphorylation to operate at optimal efficiency in the cell. Since the adenylate kinase reaction was found to buffer a thermodynamic potential, i.e. the phosphate potential, this finding was generalized to the concept of thermodynamic buffering. The thermodynamic buffering ability of the adenylate kinase reaction was demonstrated by experiments with incubated rat-liver mitochondria. Considerations of changes introduced in the entropy production by the adenylate kinase reaction allowed to establish the theoretical framework for thermodynamic buffering. The ability of thermodynamic buffering to compensate deviations from conductance matching in the presence of fluctuating loads was demonstrated by computer simulations. The possibility of other reversible ATP-utilizing reactions, like the ones catalyzed by creatine kinase and arginine kinase, to contribute to thermodynamic buffering is discussed. Finally, the comparison of the theoretically calculated steady-stae cytosolic adenine nucleotide concentrations with experimental data from perfused livers demonstrated that in livers from fed rats conductance matching is fulfilled on a

Corrosion and solubility in a TSP-buffered chemical environment following a loss of coolant accident: Part 2 – Zinc

International Nuclear Information System (INIS)

Pease, David; LaBrier, Daniel; Ali, Amir; Blandford, Edward D.; Howe, Kerry J.

2016-01-01

Highlights: • Zinc release is limited to less than 1 mg/L in TSP-buffered solution under a variety of conditions (pH, temperature, zinc source). • Zinc release in high-temperature non-TSP-buffered environment is approximately 25 mg/L. • Long-term zinc release is controlled by passivation (without TSP) and zinc solubility (with TSP). • Precipitation and solubility of zinc phosphate limit the release of zinc. - Abstract: Bench experiments were conducted to investigate the effect of the presence of trisodium phosphate (TSP) on the corrosion and release of zinc from metallic zinc-bearing surfaces under conditions representative of the containment pool following a postulated loss of coolant accident (LOCA) at a nuclear power generating facility. The experiments showed that in non-buffered (acidic) environments, measurable quantities of zinc are released from zinc-bearing surfaces. Precipitation and solubility of phosphate-based corrosion products, such as zinc phosphate, limit the release of zinc from zinc-bearing surfaces. These experiments have found that under a variety of conditions, including variations of temperature, pH, and across different zinc-bearing surfaces, the release of zinc into solution is limited to <1 mg/L when phosphate is present. When phosphate is not present, zinc release is instead bounded by a markedly higher saturation limit which is a strong function of the solution temperature.

Doped LZO buffer layers for laminated conductors

Science.gov (United States)

Paranthaman, Mariappan Parans [Knoxville, TN; Schoop, Urs [Westborough, MA; Goyal, Amit [Knoxville, TN; Thieme, Cornelis Leo Hans [Westborough, MA; Verebelyi, Darren T [Oxford, MA; Rupich, Martin W [Framingham, MA

2010-03-23

A laminated conductor includes a metallic substrate having a surface, a biaxially textured buffer layer supported by the surface of the substrate, the biaxially textured buffer layer comprising LZO and a dopant for mitigating metal diffusion through the LZO, and a biaxially textured conductor layer supported by the biaxially textured buffer layer.

Buffer regulation of calcium puff sequences

International Nuclear Information System (INIS)

Fraiman, Daniel; Dawson, Silvina Ponce

2014-01-01

Puffs are localized Ca 2+ signals that arise in oocytes in response to inositol 1,4,5-trisphosphate (IP 3 ). They are the result of the liberation of Ca 2+ from the endoplasmic reticulum through the coordinated opening of IP 3 receptor/channels clustered at a functional release site. The presence of buffers that trap Ca 2+ provides a mechanism that enriches the spatio–temporal dynamics of cytosolic calcium. The expression of different types of buffers along the cell's life provides a tool with which Ca 2+ signals and their responses can be modulated. In this paper we extend the stochastic model of a cluster of IP 3 R-Ca 2+ channels introduced previously to elucidate the effect of buffers on sequences of puffs at the same release site. We obtain analytically the probability laws of the interpuff time and of the number of channels that participate of the puffs. Furthermore, we show that under typical experimental conditions the effect of buffers can be accounted for in terms of a simple inhibiting function. Hence, by exploring different inhibiting functions we are able to study the effect of a variety of buffers on the puff size and interpuff time distributions. We find the somewhat counter-intuitive result that the addition of a fast Ca 2+ buffer can increase the average number of channels that participate of a puff. (paper)

Buffer regulation of calcium puff sequences.

Science.gov (United States)

Fraiman, Daniel; Dawson, Silvina Ponce

2014-02-01

Puffs are localized Ca(2 +) signals that arise in oocytes in response to inositol 1,4,5-trisphosphate (IP3). They are the result of the liberation of Ca(2 +) from the endoplasmic reticulum through the coordinated opening of IP3 receptor/channels clustered at a functional release site. The presence of buffers that trap Ca(2 +) provides a mechanism that enriches the spatio-temporal dynamics of cytosolic calcium. The expression of different types of buffers along the cell's life provides a tool with which Ca(2 +) signals and their responses can be modulated. In this paper we extend the stochastic model of a cluster of IP3R-Ca(2 +) channels introduced previously to elucidate the effect of buffers on sequences of puffs at the same release site. We obtain analytically the probability laws of the interpuff time and of the number of channels that participate of the puffs. Furthermore, we show that under typical experimental conditions the effect of buffers can be accounted for in terms of a simple inhibiting function. Hence, by exploring different inhibiting functions we are able to study the effect of a variety of buffers on the puff size and interpuff time distributions. We find the somewhat counter-intuitive result that the addition of a fast Ca(2 +) buffer can increase the average number of channels that participate of a puff.

Complexation in two-component chlortetracycline-melanin solutions

Science.gov (United States)

Lapina, V. A.; Pershukevich, P. P.; Dontsov, A. E.; Bel'Kov, M. V.

2008-01-01

The spectra and kinetics of fluorescence of two-component solutions of the chlortetracycline (CHTC)-DOPA-melanin (melanin or ME) system in water have been investigated. The data obtained have been compared to similar data for solutions of CHTC-melanosome from bull eye (MB), which contains natural melanin, in K-phosphate buffer at pH 7.4. The overall results indicate the occurrence of complexation between molecules of CHTC and ME as they are being excited. The studies of complexation in the solution of CHTC-MB in the buffer are complicated by the formation of a CHTC-buffer complex. The effect of optical radiation in the range 330-750 nm on the CHTC-ME complex shows selectivity: the greatest change in the spectrum occurs when the wavelength of the exciting radiation coincides with the long-wavelength band maximum of the fluorescence excitation spectrum of the CHTC-ME complex in aqueous solution. In this range, CHTC and especially ME show high photochemical stability. The nature of the radiation effect on the studied compounds in the hard UV range (λ < 330 nm) differs greatly from that in the range 330-750 nm. It is apparently accompanied by significant photochemical transmutations of all system components. By comparing the characteristics of the CHTC-ME systems with those of the related drug doxycycline (DC-ME), the conclusion has been made that the chlorine atom plays a vital role in formation of the short-wavelength band in the fluorescence spectrum of the CHTC-ME complex.

Extended wavelength InGaAs on GaAs using InAlAs buffer for back-side-illuminated short-wave infrared detectors

International Nuclear Information System (INIS)

Zimmermann, Lars; John, Joachim; Degroote, Stefan; Borghs, Gustaaf; Hoof, Chris van; Nemeth, Stefan

2003-01-01

We conducted an experimental study of back-side-illuminated InGaAs photodiodes grown on GaAs and sensitive in the short-wave infrared up to 2.4 μm. Standard metamorphic InGaAs or IR-transparent InAlAs buffers were grown by molecular-beam epitaxy. We studied dark current and photocurrent as a function of buffer thickness, buffer material, and temperature. A saturation of the dark current with buffer thickness was not observed. The maximum resistance area product was ∼10 Ω cm2 at 295 K. The dark current above 200 K was dominated by generation-recombination current. A pronounced dependence of the photocurrent on the buffer thickness was observed. The peak external quantum efficiency was 46% (at 1.6 μm) without antireflective coating

Extrusion and erosion of bentonite buffer material in a flow-through, horizontal, artificial fracture system

International Nuclear Information System (INIS)

Schatz, Timothy; Kanerva, Noora; Martikainen, Jari

2012-01-01

Document available in extended abstract form only. One scenario of interest for the long-term safety assessment of a spent nuclear fuel repository involves the loss of bentonite buffer material through contact with dilute groundwater at a transmissive fracture interface [SKB 2011, Posiva 2012]. In order to simulate the potential extrusion/erosion behaviour of bentonite buffer material in such an environment, a series of small-scale, flow-through, artificial fracture experiments were performed in which swelling clay material could extrude/erode into a well defined, system (see Figure 1). The fracture dimensions were 24 cm (length) x 24 cm (width) x 1 mm (aperture) and the compacted sample dimensions were 2 cm (height) x 2 cm (diameter). Extrusion/erosion effects were analysed against solution chemistry (salt concentration and composition), material composition (sodium montmorillonite and admixtures with calcium montmorillonite), and flow velocity. No erosion was observed for sodium montmorillonite against solution compositions from 10 to 0.5 g/L NaCl. Comparatively, most reports in the literature indicate that a concentration of 0.5 g/L NaCl (8.6 mM) is below, in some cases well below, the (experimentally observed) critical coagulation concentration (CCC) for the colloidal sodium montmorillonite/sodium chloride system [Garcia-Garcia et al. 2007]. It was also the case that no erosion was observed for 50/50 calcium/sodium montmorillonite against 0.5 g/L NaCl. Overall, the results of the flow-through, artificial fracture tests, indicate stability to erosion down to a dilute concentration range between 8 to 4 mM NaCl for both sodium and 50/50 calcium/sodium montmorillonite. These limits compare favorably to the erosion stability limits observed by Birgersson et al. [2009] in the case of the latter material but less so for the former. A number of tests were conducted for which measurable erosion was observed. The calculated mass loss rates for these tests, expressed in

Static mechanical properties of buffer material

International Nuclear Information System (INIS)

Takaji, Kazuhiko; Suzuki, Hideaki

1999-11-01

The buffer material is expected to maintain its low water permeability, self-sealing properties, radionuclides adsorption and retardation properties, thermal conductivity, chemical buffering properties, overpack supporting properties, stress buffering properties, etc. over a long period of time. Natural clay is mentioned as a material that can relatively satisfy above. Among the kinds of natural clay, bentonite when compacted is superior because (i) it has exceptionally low water permeability and properties to control the movement of water in buffer, (ii) it fills void spaces in the buffer and fractures in the host rock as it swells upon water uptake, (iii) it has the ability to exchange cations and to adsorb cationic radioelements. In order to confirm these functions for the purpose of safety assessment, it is necessary to evaluate buffer properties through laboratory tests and engineering-scale tests, and to make assessments based on the ranges in the data obtained. This report describes the procedures, test conditions, results and examinations on the buffer material of unconfined compression tests, one-dimensional consolidation tests, consolidated-undrained triaxial compression tests and consolidated-undrained triaxial creep tests that aim at getting hold of static mechanical properties. We can get hold of the relationship between the dry density and tensile stress etc. by Brazilian tests, between the dry density and unconfined compressive strength etc. by unconfined compression tests, between the consolidation stress and void ratio etc. by one-dimensional consolidation tests, the stress pass of each effective confining pressure etc. by consolidated-undrained triaxial compression tests and the axial strain rate with time of each axial stress etc. by consolidated-undrained triaxial creep tests. (author)

Optimization of protein buffer cocktails using Thermofluor.

Science.gov (United States)

Reinhard, Linda; Mayerhofer, Hubert; Geerlof, Arie; Mueller-Dieckmann, Jochen; Weiss, Manfred S

2013-02-01

The stability and homogeneity of a protein sample is strongly influenced by the composition of the buffer that the protein is in. A quick and easy approach to identify a buffer composition which increases the stability and possibly the conformational homogeneity of a protein sample is the fluorescence-based thermal-shift assay (Thermofluor). Here, a novel 96-condition screen for Thermofluor experiments is presented which consists of buffer and additive parts. The buffer screen comprises 23 different buffers and the additive screen includes small-molecule additives such as salts and nucleotide analogues. The utilization of small-molecule components which increase the thermal stability of a protein sample frequently results in a protein preparation of higher quality and quantity and ultimately also increases the chances of the protein crystallizing.

BUFFER CAPACITY IN HETEROGENEOUS MULTICOMPONENT SYSTEMS. REVIEW

Directory of Open Access Journals (Sweden)

Oxana Spinu

2015-12-01

Full Text Available The quantitative basis of the theory of buffer properties for two-phase acid-base buffer systems and for multicomponent heterogeneous systems has been derived. The analytical equations with respect to all components for diverse multicomponent systems were deduced. It has been established, that the buffer capacities of components are mutually proportional.

{sup 137}Cs sorption into bentonite from Cidadap-Tasikmalaya as buffer material for disposal demonstration plant facility at Serpong

Energy Technology Data Exchange (ETDEWEB)

Setiawan, B., E-mail: bravo@batan.go.id; Sriwahyuni, H., E-mail: bravo@batan.go.id; Ekaningrum, NE., E-mail: bravo@batan.go.id; Sumantry, T., E-mail: bravo@batan.go.id [Radwaste Technology Center-National Nuclear Energy Agency, PUSPIPTEK, Serpong-Tangerang 15310 (Indonesia)

2014-03-24

According to co-location principle, near surface disposal type the disposal demonstration plant facility will be build at Serpong nuclear area. The facility also for anticipation of future needs to provide national facility for the servicing of radwaste management of non-nuclear power plant activity in Serpong Nuclear Area. It is needs to study the material of buffer and backfill for the safety of demonstration plant facility. A local bentonite rock from Cidadap-Tasikmalaya was used as the buffer materials. Objective of experiment is to find out the specific data of sorption characteristic of Cidadap bentonite as buffer material in a radwaste disposal system. Experiments were performed in batch method, where bentonite samples were contacted with CsCl solution labeled with Cs-137 in 100 ml/g liquid:solid ratio. Initial Cs concentration was 10{sup −8} M and to study the effects of ionic strength and Cs concentration in solution, 0.1 and 1.0 M NaCl also CsCl concentration ranging 10{sup −8} - 10{sup −4} M were added in solution. As the indicator of Cs saturated in bentonite samples, Kd value was applied. Affected parameters in the experiment were contact time, effects of ionic strength and concentration of CsCl. Results showed that sorption of Cs by bentonite reached constantly after 16 days contacted, and Kd value was 10.600 ml/g. Effect of CsCl concentration on Kd value may decreased in increased in CsCl concentration. Effect of ionic strength increased according to increased in concentration of background and would effect to Kd value due to competition of Na ions and Cs in solution interacts with bentonite. By obtaining the bentonite character data as buffer material, the results could be used as the basis for making of design and the basic of performance assessment the near surface disposal facility in terms of isolation capacity of radwaste later.

Buffer lining manufacturing method for radioactive waste container

International Nuclear Information System (INIS)

Kawakami, Susumu; Sugino, Hiroyuki

1998-01-01

A recessed portion is formed on an upper surface of a filler layer made of a buffer powder filled into a container main body, the upper portion of the vessel main body is closed by a shrinkable liquid tight film. It is placed in a pressurizing container and pressed to mold a buffer lining base material integrated with the vessel main body. A flat upper surface and a containing space are formed by shaving to form a buffer lining. A disposing vessel containing radioactive wastes is inserted into the containing space, and the containing space is closed by a buffer block. The upper surface is sealed by a lid. With such a constitution, since a buffer lining integrated with the vessel main body can be formed easily inside the vessel main body, the disposing vessel can be contained in the containing vessel in a state surrounded by the buffer easily and stably without laying or piling over a large quantity of buffer blocks. (T.M.)

Comparing the acidities of aqueous, frozen, and freeze-dried phosphate buffers: Is there a "pH memory" effect?

Science.gov (United States)

Vetráková, Ľubica; Vykoukal, Vít; Heger, Dominik

2017-09-15

The concept of "pH memory" has been established in the literature for the correlation between the pH of a pre-lyophilization solution and the ionization state of freeze-dried powder (lyophile). In this paper, the concept of "pH memory" is explored for the system of an aqueous solution, a frozen solution, and a lyophile. Sodium and potassium phosphate buffers in the pH range of 5-9 were frozen and lyophilized with sulfonephthalein indicators as acidity probes, and their Hammett acidity functions were compared to the initial pH of the aqueous solution. The results show that the acidities of the lyophiles are somewhat changed compared to the initial pHs, but the acidities in the frozen state differ more substantially. The Hammett acidity functions of the frozen buffers were found to be markedly dissimilar from the initial pH, especially in the sodium phosphate frozen at 233K, where an increase in the initial pH led to a decrease in the Hammett acidity function of the frozen state at a certain pH range. The large acidification observed after freezing the sodium phosphate buffer was not detected in the lyophiles after the sample had been dried; the phenomenon is explained considering the formed crystals analyzed by X-ray powder diffraction. The results suggest that monitoring the final acidity of a lyophile is not sufficient to predict all the acidity changes throughout the whole lyophilization process. The importance of well-controlled freezing and lyophilization conditions follows from the results of the research. Copyright © 2017 Elsevier B.V. All rights reserved.

Standard Gibbs free energies for transfer of actinyl ions at the aqueous/organic solution interface

International Nuclear Information System (INIS)

Kitatsuji, Yoshihiro; Okugaki, Tomohiko; Kasuno, Megumi; Kubota, Hiroki; Maeda, Kohji; Kimura, Takaumi; Yoshida, Zenko; Kihara, Sorin

2011-01-01

Research highlights: → Standard Gibbs free energies for ion-transfer of tri- to hexavalent actinide ions. → Determination is based on distribution method combined with ion-transfer voltammetry. → Organic solvents examined are nitrobenzene, DCE, benzonitrile, acetophenone and NPOE. → Gibbs free energies of U(VI), Np(VI) and Pu(VI) are similar to each other. → Gibbs free energies of Np(V) is very large, comparing with ordinary monovalent cations. - Abstract: Standard Gibbs free energies for transfer (ΔG tr 0 ) of actinyl ions (AnO 2 z+ ; z = 2 or 1; An: U, Np, or Pu) between an aqueous solution and an organic solution were determined based on distribution method combined with voltammetry for ion transfer at the interface of two immiscible electrolyte solutions. The organic solutions examined were nitrobenzene, 1,2-dichloroethane, benzonitrile, acetophenone, and 2-nitrophenyl octyl ether. Irrespective of the type of organic solutions, ΔG tr 0 of UO 2 2+ ,NpO 2 2+ , and PuO 2 2+ were nearly equal to each other and slightly larger than that of Mg 2+ . The ΔG tr 0 of NpO 2 + was extraordinary large compared with those of ordinary monovalent cations. The dependence of ΔG tr 0 of AnO 2 z+ on the type of organic solutions was similar to that of H + or Mg 2+ . The ΔG tr 0 of An 3+ and An 4+ were also discussed briefly.

Buffer Sizing in 802.11 Wireless Mesh Networks

KAUST Repository

Jamshaid, Kamran; Shihada, Basem; Xia, Li; Levis, Philip

2011-01-01

We analyze the problem of buffer sizing for TCP flows in 802.11-based Wireless Mesh Networks. Our objective is to maintain high network utilization while providing low queueing delays. The problem is complicated by the time-varying capacity of the wireless channel as well as the random access mechanism of 802.11 MAC protocol. While arbitrarily large buffers can maintain high network utilization, this results in large queueing delays. Such delays may affect TCP stability characteristics, and also increase queueing delays for other flows (including real-time flows) sharing the buffer. In this paper we propose sizing link buffers collectively for a set of nodes within mutual interference range called the 'collision domain'. We aim to provide a buffer just large enough to saturate the available capacity of the bottleneck collision domain that limits the carrying capacity of the network. This neighborhood buffer is distributed over multiple nodes that constitute the network bottleneck; a transmission by any of these nodes fully utilizes the available spectral resource for the duration of the transmission. We show that sizing routing buffers collectively for this bottleneck allows us to have small buffers (as low as 2 - 3 packets) at individual nodes without any significant loss in network utilization. We propose heuristics to determine these buffer sizes in WMNs. Our results show that we can reduce the end-to-end delays by 6× to 10× at the cost of losing roughly 5% of the network capacity achievable with large buffers.

Buffer Sizing in 802.11 Wireless Mesh Networks

KAUST Repository

Jamshaid, Kamran

2011-10-01

We analyze the problem of buffer sizing for TCP flows in 802.11-based Wireless Mesh Networks. Our objective is to maintain high network utilization while providing low queueing delays. The problem is complicated by the time-varying capacity of the wireless channel as well as the random access mechanism of 802.11 MAC protocol. While arbitrarily large buffers can maintain high network utilization, this results in large queueing delays. Such delays may affect TCP stability characteristics, and also increase queueing delays for other flows (including real-time flows) sharing the buffer. In this paper we propose sizing link buffers collectively for a set of nodes within mutual interference range called the \\'collision domain\\'. We aim to provide a buffer just large enough to saturate the available capacity of the bottleneck collision domain that limits the carrying capacity of the network. This neighborhood buffer is distributed over multiple nodes that constitute the network bottleneck; a transmission by any of these nodes fully utilizes the available spectral resource for the duration of the transmission. We show that sizing routing buffers collectively for this bottleneck allows us to have small buffers (as low as 2 - 3 packets) at individual nodes without any significant loss in network utilization. We propose heuristics to determine these buffer sizes in WMNs. Our results show that we can reduce the end-to-end delays by 6× to 10× at the cost of losing roughly 5% of the network capacity achievable with large buffers.

Double-Blind Crossover Study to Compare Pain Experience During Inferior Alveolar Nerve Block Administration Using Buffered Two Percent Lidocaine in Children.

Science.gov (United States)

Chopra, Radhika; Jindal, Garima; Sachdev, Vinod; Sandhu, Meera

2016-01-01

Buffering of anesthetic solutions has been suggested to reduce pain on injection and onset of anesthesia. The purpose of this study was to assess the reduction in pain on injection during inferior alveolar nerve block administration in children. A double blind crossover study was designed where 30 six- to 12-year-old patients received two sessions of inferior alveolar nerve block scheduled one week apart. Two percent lidocaine with 1:200,000 epinephrine was given during one appointment, and a buffered solution was given during the other. Pain on injection was assessed using the sound, eye, and motor (SEM) scale, and the time to onset was assessed after gingival probing. The Heft-Parker visual analogue scale (HP-VAS) was self recorded by the patient after administration of local anesthesia. When tested using Mann-Whitney analysis, no significant differences were found between the SEM scores (P=0.71) and HP-VAS scores (P=0.93) for the two solutions used. Student's t test was used to assess the difference in the onset of anesthesia, which was also found to be statistically insignificant (P=0.824). Buffered lidocaine did not reduce the pain on injection or time to onset of anesthesia for inferior alveolar nerve block in children.

Comment on the Long-Term Chemical and Mineralogical Stability of the Buffer

International Nuclear Information System (INIS)

Arthur, Randy; Apted, Mick; Stenhouse, Mike

2005-03-01

This report examines concepts and data that SKB may use to assess the long-term chemical and mineralogical evolution of bentonite barriers in a KBS-3 repository for spent nuclear fuel. Three interrelated topics are considered: mineral chemistry of the smectite clays; thermodynamic stability of the smectite clays; and bentonite-water interactions during the early thermal period of repository evolution. Smectites are complex solid solutions having variable compositions resulting from ionic substitutions on exchange, octahedral and tetrahedral sites in the crystalline lattice. Although little is known about the mechanisms and rates of reactions involving the latter two sites, abundant observational evidence from natural systems suggests that such reactions could occur to an appreciable extent in the buffer over the million year time frame being considered for an intact canister. We are not aware of any efforts in SKB's current modeling strategy to account for such reactions, and therefore question whether the strategy is appropriate for modeling the long-term chemical evolution of the buffer and associated potential effects on the desirable physical and rheological properties of this barrier material. The variable chemistry of smectites affects their thermodynamic stability. Models of smectite-water equilibria use either a fixed stoichiometric composition to approximate representative smectite varieties, or account for compositional variations using solid solution models and ideal mixing relations among thermodynamic components. In either case the thermodynamic properties of a specific smectite composition or of individual solid-solution components must usually be estimated. Recent reports suggest that SKB will not account explicitly for the thermodynamic properties of smectite in its models of bentonite-water interactions. Rather, the models will assume that this clay mineral has a fixed, though unspecified, composition representing an ion-exchanger phase. This phase

Combined low-volume polyethylene glycol solution plus stimulant laxatives versus standard-volume polyethylene glycol solution: A prospective, randomized study of colon cleansing before colonoscopy

Science.gov (United States)

Hookey, Lawrence C; Depew, William T; Vanner, Stephen J

2006-01-01

INTRODUCTION The effectiveness of polyethylene glycol solutions (PEG) for colon cleansing is often limited by the inability of patients to drink adequate portions of the 4 L solution. The aim of the present study was to determine whether a reduced volume of PEG combined with stimulant laxatives would be better tolerated and as or more effective than the standard dose. METHODS Patients undergoing outpatient colonoscopy were randomly assigned to receive either low-volume PEG plus sennosides (120 mg oral sennosides syrup followed by 2 L PEG) or the standard volume preparation (4 L PEG). The subjects rated the tolerability of the preparations and their symptoms. Colonoscopists were blind to the colonic cleansing preparation and graded the cleansing efficacy using a validated tool (the Ottawa scale). RESULTS The low-volume PEG plus sennosides preparation was significantly better tolerated than the standard large volume PEG (Psennosides preparation was better tolerated, it was not as effective as standard large-volume PEG. However, in view of the significant difference in tolerance, further research investigating possible improvements in the reduced-volume regimen seems warranted. PMID:16482236

A Stable Metal-Organic Framework Featuring a Local Buffer Environment for Carbon Dioxide Fixation.

Science.gov (United States)

He, Hongming; Sun, Qi; Gao, Wenyang; Perman, Jason A; Sun, Fuxing; Zhu, Guangshan; Aguila, Briana; Forrest, Katherine; Space, Brian; Ma, Shengqian

2018-04-16

A majority of metal-organic frameworks (MOFs) fail to preserve their physical and chemical properties after exposure to acidic, neutral, or alkaline aqueous solutions, therefore limiting their practical applications in many areas. The strategy demonstrated herein is the design and synthesis of an organic ligand that behaves as a buffer to drastically boost the aqueous stability of a porous MOF (JUC-1000), which maintains its structural integrity at low and high pH values. The local buffer environment resulting from the weak acid-base pairs of the custom-designed organic ligand also greatly facilitates the performance of JUC-1000 in the chemical fixation of carbon dioxide under ambient conditions, outperforming a series of benchmark catalysts. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Efficacy of a Buffered 4% Lidocaine Formulation for Incision and Drainage: A Prospective, Randomized, Double-blind Study.

Science.gov (United States)

Harreld, Taryn Kratz; Fowler, Sara; Drum, Melissa; Reader, Al; Nusstein, John; Beck, Mike

2015-10-01

Incision and drainage of symptomatic emergency patients with facial swelling is painful even after local anesthetics are administered. The purpose of this prospective, randomized, double-blind study was to compare the pain of infiltration and the pain of an incision and drainage procedure of a buffered versus a nonbuffered 4% lidocaine formulation in symptomatic emergency patients presenting with a diagnosis of pulpal necrosis, associated periapical area, and an acute clinical swelling. Eighty-eight emergency patients were randomly divided into 2 groups to receive 2 intraoral infiltration injections (mesial and distal to the swelling) of either 4% lidocaine with 1:100,000 epinephrine buffered with 0.18 mL 8.4% sodium bicarbonate using the Onpharma (Los Gatos, CA) buffering system or 4% lidocaine with 1:100,000 epinephrine. Subjects rated the pain of needle insertion, needle placement, and solution deposition for each injection using a 170-mm visual analog scale. An incision and drainage procedure was performed, and subjects rated the pain of incision, drainage, and dissection on a 170-mm visual analog scale. No significant differences between the buffered and nonbuffered 4% lidocaine formulations were found for needle insertion, placement, and solution deposition of the infiltration injections or for the treatment phases of incision, drainage, and dissection. Buffering a 4% lidocaine formulation did not significantly decrease the pain of infiltrations or significantly decrease the pain of the incision and drainage procedure when compared with a nonbuffered 4% lidocaine formulation in symptomatic patients with a diagnosis of pulpal necrosis and associated acute swelling. Copyright © 2015 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

BENTO buffer development program in Finland - Key issues

International Nuclear Information System (INIS)

Autio, J.; Korkiala-Tanttu, L.; Vaehaenen, M.; Koskinen, K.; Korkeakoski, P.; Haapala, K.

2010-01-01

Document available in extended abstract form only. Posiva launched a programme, BENTO, to develop technology of using bentonite in spent nuclear fuel repositories. The main purpose of the BENTO programme is to produce buffer designs and verify that they fulfil the requirements, especially safety requirements. To achieve this objective, resources and the level of expertise and know-how has to be increased. There are several uncertainties related to the functioning of the buffer components at present. An issue is defined as being significant if there is sufficient uncertainty that the buffer system might not fulfil the requirements because of the issue. These significant issues need to be resolved in order to develop a proper design and to verify the fulfilment of the requirements. The list of significant issues may change with time. Therefore it is crucial to develop adequate expertise, know-how and laboratory facilities to manage the changes. Moreover, there is confidence that by solving the open issues a defendable construction license application can be submitted in 2012. The basic nature of the programme is a combination of material and process research with the design and manufacturing of buffer components to produce feasible buffer design with proven long-term functional properties. The development work carried out under BENTO-programme has been initially divided into four different projects. During the course of work the number of projects and their content can be adjusted. The four BENTO projects are: 1. Manufacturing (MANU); 2. Design (DESI); 3. Modelling (MODE); 4. Material and Process Research (MARE). BENTO programme aims at producing feasible buffer designs which fulfil the requirements specified in Posiva's requirement management system. The designs are produced in DESI-project by following the design development scheme which starts from specification of design basis and ends in documented detailed designs and therefore DESIgn is specified as one

Chemical buffering in natural and engineered barrier systems: Thermodynamic constraints and performance assessment consequences

International Nuclear Information System (INIS)

Arthur, R.C.; Wei Zhou

2000-12-01

Thermodynamic and kinetic constraints on the chemical buffering properties of natural and engineered-barrier systems are derived in this study from theoretical descriptions, incorporated in the reaction-path model, of reversible and irreversible mass transfer in multicomponent, multiphase systems. The buffering properties of such systems are conditional properties because they refer to a specific aqueous species in a system that is open with respect to a specific reactant. The solution to a mathematical statement of this concept requires evaluation of the dependence of the activity of the buffered species on incremental changes in the overall reaction-progress variable. This dependence can be represented by a truncated Taylor's series expansion, where the values of associated derivatives are calculated using finite-difference techniques and mass-balance, charge-balance and mass-action constraints. Kinetic constraints on buffering behavior can also be described if the relation between reactant flux and reaction rate is well defined. This relation is explicit for the important case of advective groundwater flow and water-rock interaction. We apply the theoretical basis of the chemical buffering concept to processes that could affect the performance of a deep geologic repository for nuclear waste. Specifically, we focus on the likelihood that an inverse relation must exist between the buffer intensity and the migration velocity of reaction fronts in systems involving advective or diffusive mass transport. A quantitative understanding of this relation would provide the basis for evaluating the potential role of chemical buffering in achieving the isolation and retardation functions, of the EBS and geosphere in a KBS-3 repository. Our preliminary evaluation of this role considers the effects of chemical buffering on the propagation velocity of a pH front in both the near- and far field. We use a geochemical modeling technique compatible with the reaction-path model to

Standard test method for isotopic analysis of hydrolyzed uranium hexafluoride and uranyl nitrate solutions by thermal ionization mass spectrometry

CERN Document Server

American Society for Testing and Materials. Philadelphia

2005-01-01

1.1 This method applies to the determination of isotopic composition in hydrolyzed nuclear grade uranium hexafluoride. It covers isotopic abundance of 235U between 0.1 and 5.0 % mass fraction, abundance of 234U between 0.0055 and 0.05 % mass fraction, and abundance of 236U between 0.0003 and 0.5 % mass fraction. This test method may be applicable to other isotopic abundance providing that corresponding standards are available. 1.2 This test method can apply to uranyl nitrate solutions. This can be achieved either by transforming the uranyl nitrate solution to a uranyl fluoride solution prior to the deposition on the filaments or directly by depositing the uranyl nitrate solution on the filaments. In the latter case, a calibration with uranyl nitrate standards must be performed. 1.3 This test method can also apply to other nuclear grade matrices (for example, uranium oxides) by providing a chemical transformation to uranyl fluoride or uranyl nitrate solution. 1.4 This standard does not purport to address al...

Effect of buffer on the immune response to trivalent oral poliovirus vaccine in Bangladesh: a community based randomized controlled trial.

Science.gov (United States)

Chandir, Subhash; Ahamed, Kabir U; Baqui, Abdullah H; Sutter, Roland W; Okayasu, Hiromasa; Pallansch, Mark A; Oberste, Mark S; Moulton, Lawrence H; Halsey, Neal A

2014-11-01

Polio eradication efforts have been hampered by low responses to trivalent oral poliovirus vaccine (tOPV) in some developing countries. Since stomach acidity may neutralize vaccine viruses, we assessed whether administration of a buffer solution could improve the immunogenicity of tOPV. Healthy infants 4-6 weeks old in Sylhet, Bangladesh, were randomized to receive tOPV with or without a sodium bicarbonate and sodium citrate buffer at age 6, 10, and 14 weeks. Levels of serum neutralizing antibodies for poliovirus types 1, 2, and 3 were measured before and after vaccination, at 6 and 18 weeks of age, respectively. Serologic response rates following 3 doses of tOPV for buffer recipients and control infants were 95% and 88% (P=.065), respectively, for type 1 poliovirus; 95% and 97% (P=.543), respectively, for type 2 poliovirus; and 90% and 89% (P=.79), respectively, for type 3 poliovirus. Administration of a buffer solution prior to vaccination was not associated with statistically significant increases in the immune response to tOPV; however, a marginal 7% increase (P=.065) in serologic response to poliovirus type 1 was observed. NCT01579825. © The Author 2014. Published by Oxford University Press on behalf of the Infectious Diseases Society of America. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Activity of NaOH buffered by silicate solids in molten sodium acetate-water at 3170C

International Nuclear Information System (INIS)

Weres, O.; Tsao, L.

1988-01-01

Silica and sodium acetate are present in the steam generator tube sheet crevices of many nuclear power plants. Trace solutes in the condensate are tremendously concentrated in the crevices by boiling. Sparingly soluble sodium silicates and other solids precipitate from the crevice liquid leaving an extremely concentrated molten mixture of water, sodium acetate and other salts. The precipitates buffer the activity of sodium hydroxide in the superheated liquid that remains. The activity of NaOH corresponding to the buffers quartz/sodium disilicate and sodium disilicate/sodium metasilicate at 317 0 C has been determined experimentally. The sodium hydroxide content of a sodium acetate-water melt buffered by these reactions was determined by chemical analysis, and the corresponding activity of NaOH at temperature was calculated using the recently published Pitzer-Simonson Model of molten salt-water mixtures. The molten mixture of sodium acetate and water plays the role solvent in these experiments and calculations. The free energies of formation of solid sodium silicates at 317 0 C were also determined. The activity of NaOH corresponding to other silicate and phosphate buffers was calculated using published thermodynamic data and estimated from phase diagrams

Chemical buffering in natural and engineered barrier systems: Thermodynamic constraints and performance assessment consequences

Energy Technology Data Exchange (ETDEWEB)

Arthur, R.C.; Wei Zhou [Monitor Scientific, LLC, Denver, CO (United States)

2000-12-01

Thermodynamic and kinetic constraints on the chemical buffering properties of natural and engineered-barrier systems are derived in this study from theoretical descriptions, incorporated in the reaction-path model, of reversible and irreversible mass transfer in multicomponent, multiphase systems. The buffering properties of such systems are conditional properties because they refer to a specific aqueous species in a system that is open with respect to a specific reactant. The solution to a mathematical statement of this concept requires evaluation of the dependence of the activity of the buffered species on incremental changes in the overall reaction-progress variable. This dependence can be represented by a truncated Taylor's series expansion, where the values of associated derivatives are calculated using finite-difference techniques and mass-balance, charge-balance and mass-action constraints. Kinetic constraints on buffering behavior can also be described if the relation between reactant flux and reaction rate is well defined. This relation is explicit for the important case of advective groundwater flow and water-rock interaction. We apply the theoretical basis of the chemical buffering concept to processes that could affect the performance of a deep geologic repository for nuclear waste. Specifically, we focus on the likelihood that an inverse relation must exist between the buffer intensity and the migration velocity of reaction fronts in systems involving advective or diffusive mass transport. A quantitative understanding of this relation would provide the basis for evaluating the potential role of chemical buffering in achieving the isolation and retardation functions, of the EBS and geosphere in a KBS-3 repository. Our preliminary evaluation of this role considers the effects of chemical buffering on the propagation velocity of a pH front in both the near- and far field. We use a geochemical modeling technique compatible with the reaction-path model

The Buffer and Backfill Handbook. Part 3: Models for calculation of processes and behaviour

Energy Technology Data Exchange (ETDEWEB)

Pusch, Roland [Geodevelopment AB, Lund (Sweden)

2003-01-15

nature. They are coupled to other processes and affected by various restrictions such as limited access to water and transient interaction with dissolved species. This makes the issue of coupled models very important but almost all the models and codes that are being used in predicting the behaviour of buffers and backfills in a repository are simplified and incomplete with respect to the hydrothermal processes. This is because of the lack of understanding of the involved physico-chemical mechanisms, for which consideration of the behaviour of the clay on the microstructural level is required. Chapter 3 deals with microstructural issues focusing on particle interaction and void distribution in buffers and backfills with special respect to swelling pressure and permeation of fluids and gas. Chapter 4 deals with heat transport in fully and partly water saturated buffer clays. It includes mathematical formulation of empirically deduced material models of heat conductivity and gives examples of how this quantity can be evaluated from laboratory experiments. Chapter 5 deals with flow of water in liquid and vapour form in fully and partly water saturated buffers and backfills. The presented material models are intended for practical use and imply that potential theory in the form of Navier/Stoke's laws for analytical solution or numerical methods are valid. Chapter 6 gives the basis of currently used material models for anion and cation diffusion through smectitic soil. Complexation may cause considerable deviation from theoretically derived migration rates and only diffusive transport of species that do not undergo chemical reactions is treated here. Focus is on outlining the formulation of theoretical models for evaluation of diffusion coefficients from controlled experiments. As for water transport, the solution of practical 2 and 3D problems is made by use of potential theory, applying analytical or numerical techniques, which are not treated here. Chapter 7 deals

Characterization of the Redox reaction of V(V) in Ammonia Buffers with Square-Wave Voltammetry

OpenAIRE

Mirceski, Valentin; Gulaboski, Rubin; Petrovska-Jovanovic, Simka; Stojanova, Kornelija

2001-01-01

The redox reaction of V(V) in ammonia buffers solution with pH = 8.60 was studied by means of square-wave and cyclic voltammetry. The redox reaction studied exhibits properties of a surface redox process in which both the reactant and the product of the redox reaction are immobilized on the electrode surface.

Fibril growth kinetics link buffer conditions and topology of 3D collagen I networks.

Science.gov (United States)

Kalbitzer, Liv; Pompe, Tilo

2018-02-01

Three-dimensional fibrillar networks reconstituted from collagen I are widely used as biomimetic scaffolds for in vitro and in vivo cell studies. Various physicochemical parameters of buffer conditions for in vitro fibril formation are well known, including pH-value, ion concentrations and temperature. However, there is a lack of a detailed understanding of reconstituting well-defined 3D network topologies, which is required to mimic specific properties of the native extracellular matrix. We screened a wide range of relevant physicochemical buffer conditions and characterized the topology of the reconstituted 3D networks in terms of mean pore size and fibril diameter. A congruent analysis of fibril formation kinetics by turbidimetry revealed the adjustment of the lateral growth phase of fibrils by buffer conditions to be key in the determination of pore size and fibril diameter of the networks. Although the kinetics of nucleation and linear growth phase were affected by buffer conditions as well, network topology was independent of those two growth phases. Overall, the results of our study provide necessary insights into how to engineer 3D collagen matrices with an independent control over topology parameters, in order to mimic in vivo tissues in in vitro experiments and tissue engineering applications. The study reports a comprehensive analysis of physicochemical conditions of buffer solutions to reconstitute defined 3D collagen I matrices. By a combined analysis of network topology, i.e., pore size and fibril diameter, and the kinetics of fibril formation we can reveal the dependence of 3D network topology on buffer conditions, such as pH-value, phosphate concentration and sodium chloride content. With those results we are now able to provide engineering strategies to independently tune the topology parameters of widely used 3D collagen scaffolds based on the buffer conditions. By that, we enable the straightforward mimicking of extracellular matrices of in vivo

Biodesulfurization of vanadium-bearing titanomagnetite concentrates and pH control of bioleaching solution

Science.gov (United States)

Liu, Xiao-rong; Jiang, Sheng-cai; Liu, Yan-jun; Li, Hui; Wang, Hua-jun

2013-10-01

Vanadium-bearing titanomagnetite concentrates were desulfurized with Acidithiobacillus ferrooxidans ( A. ferrooxidans). The sulfur content of the concentrates was reduced from 0.69wt% to 0.14wt% after bioleaching for 15 d with a 10% pulp density at 30°C. Maintaining a stable pH value during biodesulfurization was critical because of high acid consumption, resulting from a combination of nonoxidative and oxidative dissolution of pyrrhotite in acid solution. It is discovered that the citric acid-disodium hydrogen phosphate buffer of pH 2.0 can control the solution pH value smoothly in the optimal range of 2.0-3.0 for A. ferrooxidans growth. Using the buffer in the volume fraction range of 5.0%-15.0% stimulates A. ferrooxidans growth and improves the biodesulfurization efficiency. Compared with the buffer-free control case, the maximum increase of biodesulfurization rate is 29.7% using a 10.0vol% buffer. Bioleaching provides an alternative process for desulfurization of vanadium-bearing titanomagnetite ores.

Effectiveness of the GAEC cross compliance standards Rational management of set aside, Grass strips to control soil erosion and Vegetation buffers along watercourses on surface animal diversity and biological quality of soil

Directory of Open Access Journals (Sweden)

Marta Biaggini

2011-08-01

Full Text Available Landscape simplification and loss of natural and semi-natural habitats are the major causes of biodiversity decrease in agricultural landscapes. In order to mitigate the effects of intensive agricultural management the Ministry of Agricultural, Food and Forestry Policies in Italy has included the agronomic measures Rational management of set aside, Grass strips to control soil erosion and Vegetation buffers along watercourses in the decree on cross compliance. In this paper we review the results of a field research performed in Central Italy. The aim of the study was to evaluate the efficacy of the above mentioned GAEC standards for animal diversity enhancement. Using different animal groups as indicators, superficial Arthropod fauna and Herpetofauna, we found striking differences in the biodiversity levels of areas characterized by the application or by the lack of GAEC standards, with the latter being characterized by a significatively impoverished fauna. In particular, the set aside area and the buffer of riparian vegetation resulted of primary importance to allow higher biodiversity levels. Also the analysis of the biological quality of the soil, as assessed through the QBS-ar index based on edaphic micro-Arthropod fauna, indicated a higher quality of semi-natural habitats with respect to arable lands.

Smart maintenance of riverbanks using a standard data layer and Augmented Reality

Science.gov (United States)

Pierdicca, Roberto; Frontoni, Emanuele; Zingaretti, Primo; Mancini, Adriano; Malinverni, Eva Savina; Tassetti, Anna Nora; Marcheggiani, Ernesto; Galli, Andrea

2016-10-01

Linear buffer strips (BS) along watercourses are commonly adopted to reduce run-off, accumulation of bank-top sediments and the leaking of pesticides into fresh-waters, which strongly increase water pollution. However, the monitoring of their conditions is a difficult task because they are scattered over wide rural areas. This work demonstrates the benefits of using a standard data layer and Augmented Reality (AR) in watershed control and outlines the guideline of a novel approach for the health-check of linear BS. We designed a mobile environmental monitoring system for smart maintenance of riverbanks by embedding the AR technology within a Geographical Information System (GIS). From the technological point of view, the system's architecture consists of a cloud-based service for data sharing, using a standard data layer, and of a mobile device provided with a GPS based AR engine for augmented data visualization. The proposed solution aims to ease the overall inspection process by reducing the time required to run a survey. Indeed, ordinary operational survey conditions are usually performed basing the fieldwork on just classical digitized maps. Our application proposes to enrich inspections by superimposing information on the device screen with the same point of view of the camera, providing an intuitive visualization of buffer strip location. This way, the inspection officer can quickly and dynamically access relevant information overlaying geographic features, comments and other contents in real time. The solution has been tested in fieldwork to prove at what extent this cutting-edge technology contributes to an effective monitoring over large territorial settings. The aim is to encourage officers, land managers and practitioners toward more effective monitoring and management practices.

A parallel buffer tree

DEFF Research Database (Denmark)

Sitchinava, Nodar; Zeh, Norbert

2012-01-01

We present the parallel buffer tree, a parallel external memory (PEM) data structure for batched search problems. This data structure is a non-trivial extension of Arge's sequential buffer tree to a private-cache multiprocessor environment and reduces the number of I/O operations by the number of...... in the optimal OhOf(psortN + K/PB) parallel I/O complexity, where K is the size of the output reported in the process and psortN is the parallel I/O complexity of sorting N elements using P processors....

Biomass carbon, nitrogen and phosphorus stocks in hybrid poplar buffers, herbaceous buffers and natural woodlots in the riparian zone on agricultural land.

Science.gov (United States)

Fortier, Julien; Truax, Benoit; Gagnon, Daniel; Lambert, France

2015-05-01

In many temperate agricultural areas, riparian forests have been converted to cultivated land, and only narrow strips of herbaceous vegetation now buffer many farm streams. The afforestation of these riparian zones has the potential to increase carbon (C) storage in agricultural landscapes by creating a new biomass sink for atmospheric CO2. Occurring at the same time, the storage of nitrogen (N) and phosphorus (P) in plant biomass, is an important water quality function that may greatly vary with types of riparian vegetation. The objectives of this study were (1) to compare C, N and P storage in aboveground, belowground and detrital biomass for three types of riparian vegetation cover (9-year-old hybrid poplar buffers, herbaceous buffers and natural woodlots) across four agricultural sites and (2) to determine potential vegetation cover effects on soil nutrient supply rate in the riparian zone. Site level comparisons suggest that 9-year-old poplar buffers have stored 9-31 times more biomass C, 4-10 times more biomass N, and 3-7 times more biomass P than adjacent non managed herbaceous buffers, with the largest differences observed on the more fertile sites. The conversion of these herbaceous buffers to poplar buffers could respectively increase C, N and P storage in biomass by 3.2-11.9 t/ha/yr, 32-124 kg/ha/yr and 3.2-15.6 kg/ha/yr, over 9 years. Soil NO3 and P supply rates during the summer were respectively 57% and 66% lower in poplar buffers than in adjacent herbaceous buffers, potentially reflecting differences in nutrient storage and cycling between the two buffer types. Biomass C ranged 49-160 t/ha in woodlots, 33-110 t/ha in poplar buffers and 3-4 t/ha in herbaceous buffers. Similar biomass C stocks were found in the most productive poplar buffer and three of the four woodlots studied. Given their large and varied biomass C stocks, conservation of older riparian woodlots is equally important for C balance management in farmland. In addition, the

Dissolution and solubility behavior of fenofibrate in sodium lauryl sulfate solutions.

Science.gov (United States)

Granero, Gladys E; Ramachandran, Chandrasekharan; Amidon, Gordon L

2005-10-01

The solubility of fenofibrate in pH 6.8 McIlvaine buffers containing varying concentrations of sodium lauryl sulfate was determined. The dissolution behavior of fenofibrate was also examined in the same solutions with rotating disk experiments. It was observed that the enhancement in intrinsic dissolution rate was approximately 500-fold and the enhancement in solubility was approximately 2000-fold in a pH 6.8 buffer containing 2% (w/v) sodium lauryl sulfate compared to that in buffer alone. The micellar solubilization equilibrium coefficient (k*) was estimated from the solubility data and found to be 30884+/-213 L/mol. The diffusivity for the free solute, 7.15x10(-6) cm2/s, was calculated using Schroeder's additive molal volume estimates and Hayduk-Laurie correlation. The diffusivity of the drug-loaded micelle, estimated from the experimental solubility and dissolution data and the calculated value for free solute diffusivity, was 0.86x10(-6) cm2/s. Thus, the much lower enhancement in dissolution of fenofibrate compared to its enhancement in solubility in surfactant solutions appears to be consistent with the contribution to the total transport due to enhanced micellar solubilization as well as a large decrease (approximately 8-fold) in the diffusivity of the drug-loaded micelle.

Analysis of Radio communication solutions in small and isolated communities under the IEEE 802.22 standard

OpenAIRE

Arroyo Arzubi, Alejandro; Castro Lechtaler, Antonio; Foti, Antonio Roberto; Fusario, Rubén J.; García Guibout, Jorge; Sens, Lorena

2013-01-01

In recent years the use of wireless communications has increased significantly. Rural communities without cable network communication have found a solution in wireless technologies. Based on previous fieldwork, this paper analyzes software development of integration based technologies for communication equipment. It focuses on the feasibility of the IEEE 802.22 standard as a solution to the wireless problem.

Convergence and periodic solutions for the input impedance of a standard ladder network

International Nuclear Information System (INIS)

Ucak, C; Acar, C

2007-01-01

The input impedance of an infinite ladder network is computed by using the recursive relation and by assuming that the input impedance does not change when a new block is added to the network. However, this assumption is not true in general and standard textbooks do not always treat these networks correctly. This paper develops a general solution to obtain the input impedance of a standard ladder network of impedances and admittances for any number of blocks. Then, this result is used to provide the convergence condition for the infinite ladder network. The conditions which lead to periodic input impedance are exploited. It is shown that there are infinite numbers of periodic points and no paradoxical behaviour exists in the standard ladder network

The Role of Green Infrastructure Solutions in Urban Flood Risk Management

OpenAIRE

Soz, Salman Anees; Kryspin-Watson, Jolanta; Stanton-Geddes, Zuzana

2016-01-01

This Knowledge Note explores the role of green infrastructure solutions in urban flood risk management. Green infrastructure solutions represent an approach that focuses on using natural processes for managing wet weather impacts while delivering environmental, social, and economic benefits. Green infrastructure solutions, such as wetlands, bioshields, buffer zones, green roofing, street s...

Thermophysical tests of buffer materials

Energy Technology Data Exchange (ETDEWEB)

Suzuki, H. [ITC, Tokyo (Japan); Taniguchi, Wataru

1999-03-01

Thermodynamic properties of buffer materials were measured for putting in order thermodynamic constants to be used in the near-field thermal analysis. The thermal diffusivity and thermal conductivity were measured as functions of the water content and temperature to deduce the specific heat. The thermal conductivity and specific heat varied significantly as the water content changed. Obtained values of the specific heat agreed well the expected values calculated based on the constituents of the buffer material. Temperature dependence of the thermodynamic constants was found small below 90degC. From the findings, the thermal conductivity and specific heat of the buffer material were formulated as functions of the water content. Thermodynamic study of powdery bentonite was carried out as well with a purpose of use for filling apertures in the artificial barrier. (H. Baba)

Surface Water Protection by Productive Buffers

DEFF Research Database (Denmark)

Christen, Benjamin

Vegetated riparian buffer zones are a widely recommended best management practice in agriculture for protecting surface and coastal waters from diffuse nutrient pollution. On the background of the EU funded research project NitroEurope (NEU; www.NitroEurope.eu), this study concentrates...... on the mitigation of nitrogen pollution in surface and groundwater, using riparian buffer zones for biomass production. The objectives are to map suitable areas for buffer implementation across the six NEU study landscapes, model tentative N-loss mitigation, calculate biomass production potential and economic...... designed for local conditions could be a way of protecting water quality attractive to many stakeholders....

Transmitter release modulation in nerve terminals of rat neocortical pyramidal cells by intracellular calcium buffers

Science.gov (United States)

Ohana, Ora; Sakmann, Bert

1998-01-01

Dual whole-cell voltage recordings were made from synaptically connected layer 5 (L5) pyramidal neurones in slices of the young (P14-P16) rat neocortex. The Ca2+ buffers BAPTA or EGTA were loaded into the presynaptic neurone via the pipette recording from the presynaptic neurone to examine their effect on the mean and the coefficient of variation (c.v.) of single fibre EPSP amplitudes, referred to as unitary EPSPs. The fast Ca2+ buffer BAPTA reduced unitary EPSP amplitudes in a concentration dependent way. With 0.1 mm BAPTA in the pipette, the mean EPSP amplitude was reduced by 14 ± 2.8% (mean ±s.e.m., n = 7) compared with control pipette solution, whereas with 1.5 mm BAPTA, the mean EPSP amplitude was reduced by 72 ± 1.5% (n = 5). The concentration of BAPTA that reduced mean EPSP amplitudes to one-half of control was close to 0.7 mm. Saturation of BAPTA during evoked release was tested by comparing the effect of loading the presynaptic neurone with 0.1 mm BAPTA at 2 and 1 mm[Ca2+]o. Reducing [Ca2+]o from 2 to 1 mm, thereby reducing Ca2+ influx into the terminals, decreased the mean EPSP amplitude by 60 ± 2.2% with control pipette solution and by 62 ± 1.9% after loading with 0.1 mm BAPTA (n = 7). The slow Ca2+ buffer EGTA at 1 mm reduced mean EPSP amplitudes by 15 ± 2.5% (n = 5). With 10 mm EGTA mean EPSP amplitudes were reduced by 56 ± 2.3% (n = 4). With both Ca2+ buffers, the reduction in mean EPSP amplitudes was associated with an increase in the c.v. of peak EPSP amplitudes, consistent with a reduction of the transmitter release probability as the major mechanism underlying the reduction of the EPSP amplitude. The results suggest that in nerve terminals of thick tufted L5 pyramidal cells the endogenous mobile Ca2+ buffer is equivalent to less than 0.1 mm BAPTA and that at many release sites of pyramidal cell terminals the Ca2+ channel domains overlap, a situation comparable with that at large calyx-type terminals in the brainstem. PMID:9782165

Moisture buffer value: A comprehensive analysis of essential parameters

DEFF Research Database (Denmark)

Peuhkuri, Ruut Hannele; Rode, Carsten; Hansen, Kurt Kielsgaard

2006-01-01

There is an increasing focus on the possibilities of utilizing the absorptive ability of porous materials to create passive control of relative humidity (RH) variations in the indoor air.This has led to the need for determination of a newparameter that can be used for characterization of materials.......The dynamic nature of the buffering phenomena makes it difficult to use the standard hygrothermal material properties directly for this purpose. In this paper some experimental results on aerated cellular concrete are used for pointing out the methodological and experimental use of dynamic tests...

A study on manufacturing and construction method of buffer

International Nuclear Information System (INIS)

Chijimatsu, Masakazu; Sugita, Yutaka; Amemiya, Kiyoshi

1999-09-01

As an engineered barrier system in the geological disposal of high-level waste, multibarrier system is considered. Multibarrier system consists of the vitrified waste, the overpack and the buffer. Bentonite is one of the potential material as the buffer because of its low water permeability, self-sealing properties, radionuclides adsorption and retardation properties, thermal conductivity, chemical buffering properties, overpack supporting properties, stress buffering properties, etc. In order to evaluate the functions of buffer, a lot of experiments has been conducted. The evaluations of these functions are based on the assumption that the buffer is emplaced or constructed in the disposal tunnel (or disposal pit) properly. Therefore, it is necessary to study on the manufacturing / construction method of buffer. As the manufacturing / construction technology of the buffer, the block installation method and in-situ compaction method, etc, are being investigated. The block installation method is to emplace the buffer blocks manufactured in advance at the ground facility, and construction processes of the block installation method at the underground will be simplified compared with the in-situ compaction method. On the other hand, the in-situ compaction method is to introduce the buffer material with specified water content into the disposal tunnel and to make the buffer with high density at the site using a compaction machine. In regard to the in-situ compaction method, it is necessary to investigate the optimum finished thickness of one layer because it is impossible to construct the buffer at one time. This report describes the results of compaction property test and the summary of the past investigation results in connection with the manufacturing / construction method. Then this report shows the construction method that will be feasible in the actual disposal site. (J.P.N.)

Social Buffering of Stress in Development: A Career Perspective

Science.gov (United States)

Gunnar, Megan R.

2016-01-01

This review provides a broad overview of my research group's work on social buffering in human development in the context of the field. Much of the focus is on social buffering of the hypothalamic-pituitary-adrenocortical (HPA) system, one of the two major arms of the mammalian stress system. This focus reflects the centrality of the HPA system in research on social buffering in the fields of developmental psychobiology and developmental science. However, buffering of the cardiovascular and autonomic nervous system is also discussed. The central developmental question in this area derives from attachment theory which argues that the infant's experience of stress and arousal regulation in the context of her early attachment relationships is not an immature form of social buffering experienced in adulthood, but rather the foundation out of which individual differences in the capacity to gain stress relief from social partners emerge. The emergence of social buffering in infancy, changes in social buffering throughout childhood and adolescence, the influence of early experience on later individual differences in social buffering, and critical gaps in our knowledge are described. PMID:28544861

Bus Implementation Using New Low Power PFSCL Tristate Buffers

Directory of Open Access Journals (Sweden)

Neeta Pandey

2016-01-01

Full Text Available This paper proposes new positive feedback source coupled logic (PFSCL tristate buffers suited to bus applications. The proposed buffers use switch to attain high impedance state and modify the load or the current source section. An interesting consequence of this is overall reduction in the power consumption. The proposed tristate buffers consume half the power compared to the available switch based counterpart. The issues with available PFSCL tristate buffers based bus implementation are identified and benefits of employing the proposed tristate buffer topologies are put forward. SPICE simulation results using TSMC 180 nm CMOS technology parameters are included to support the theoretical formulations. The performance of proposed tristate buffer topologies is examined on the basis of propagation delay, output enable time, and power consumption. It is found that one of the proposed tristate buffer topology outperforms the others in terms of all the performance parameters. An examination of behavior of available and the proposed PFSCL tristate buffer topologies under parameter variations and mismatch shows a maximum variation of 14%.

Buffers for biomass production in temperate European agriculture

DEFF Research Database (Denmark)

Christen, Benjamin; Dalgaard, Tommy

2013-01-01

, environmental pressures from intensive agriculture and policy developments. Use of conservation buffers by farmers outside of designated schemes is limited to date, but the increasing demand for bioenergy and the combination of agricultural production with conservation calls for a much wider implementation....... This paper reviews the biophysical knowledge on buffer functioning and associated ecosystem services. It describes how a three-zone buffer design, with arable fields buffered in combination by grassland, short rotation forestry (SRF) or coppice (SRC) and undisturbed vegetation along water courses, can...... be incorporated into farming landscapes as productive conservation elements and reflects on the potential for successful implementation. Land use plays a much greater role in determining catchment hydrology than soil type: shelterbelts or buffer strips have markedly higher infiltration capacity than arable...

Double-Blind Comparison of Phlebitis Produced by Cephalothin Infusions with Buffered and Unbuffered Diluents

Science.gov (United States)

Carrizosa, Jaime; Levison, Matthew E.; Kaye, Donald

1974-01-01

In a double-blind study with each patient as his own control, a buffered and an unbuffered cephalothin solution was administered to 13 patients in opposite arms for a period of 48 h each. Neither the incidence of phlebitis nor the degree of phlebitis was different with the two diluents, and there was no difference in the time of onset of phlebitis. PMID:4840431

Electrochemical preparation of MoO{sub 3} buffer layer deposited onto the anode in organic solar cells

Energy Technology Data Exchange (ETDEWEB)

Gacitua, M.; Soto, G.; Valle, M.A. del [Pontificia Universidad Catolica de Chile, Facultad de Quimica, Laboratorio de Electroquimica de Polimeros (LEP), Santiago (Chile); Boutaleb, Y.; Rehamnia, R. [Laboratoire d' Electrochimie, Universite Badji Mokhtar, Annaba (Algeria); Cattin, L.; Louarn, G. [Universite de Nantes, Nantes Atlantique Universites, Institut des Materiaux Jean Rouxel (IMN)-CNRS, Faculte des Sciences et Techniques, Nantes (France); Abe, S.Y. [Laboratoire de Physique de la Matiere Condensee et de Technologie (LPMCT), Universite de Cocody (Ivory Coast); Lare, Y. [Laboratoire d' Energie Solaire, Universite de Lome, Lome (Togo); Morsli, M; Bernede, J.C. [Universite de Nantes, Nantes Atlantique Universites, LAMP, EA 3825, Faculte des Sciences et des Techniques, Nantes (France); Drici, A. [LEREC Departement de physique, Universite Badji Mokhtar, Annaba (Algeria)

2010-08-15

In this work the authors have studied the advantages of using electrochemically deposited molybdenum oxide as a buffer layer in an organic bilayer heterojunction solar cell arrangement. Furthermore, it has been probed that electrochemistry provides an alternative low cost, reproducible and less laborious method to prepare thin layered deposits. The precursor solution is composed by a concentrated molybdic acid solution in a sulphuric media in order to ensure the obtainment of low reduced molybdenum species. Therefore, by means of potentiostatic techniques, ITO/molybdenum oxide transparent anodes were tested for the photovoltaic device showing improved surface properties. XDR and AFM techniques were used to characterize the morphology of the deposits. The films with optimum thickness (5 nm) are amorphous. XPS analysis indicates that the best results in solar cell performance are in hand with a heterogeneous composition of the molybdenum oxide film presenting Mo{sup V} and Mo{sup VI} as predominant species. The MoO{sub 3} films deposited by cyclic voltammetry are not as homogeneous as those deposited by potentiostatic technique and only Mo{sup VI} species are present. These differences may justify the different behaviour of the solar cells using these different buffer layers. Only buffer layers deposited by potentiostatic technique allow improving the cells performances in the same way than those achieved by evaporation. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

A two-stage stochastic rule-based model to determine pre-assembly buffer content

Science.gov (United States)

Gunay, Elif Elcin; Kula, Ufuk

2018-01-01

This study considers instant decision-making needs of the automobile manufactures for resequencing vehicles before final assembly (FA). We propose a rule-based two-stage stochastic model to determine the number of spare vehicles that should be kept in the pre-assembly buffer to restore the altered sequence due to paint defects and upstream department constraints. First stage of the model decides the spare vehicle quantities, where the second stage model recovers the scrambled sequence respect to pre-defined rules. The problem is solved by sample average approximation (SAA) algorithm. We conduct a numerical study to compare the solutions of heuristic model with optimal ones and provide following insights: (i) as the mismatch between paint entrance and scheduled sequence decreases, the rule-based heuristic model recovers the scrambled sequence as good as the optimal resequencing model, (ii) the rule-based model is more sensitive to the mismatch between the paint entrance and scheduled sequences for recovering the scrambled sequence, (iii) as the defect rate increases, the difference in recovery effectiveness between rule-based heuristic and optimal solutions increases, (iv) as buffer capacity increases, the recovery effectiveness of the optimization model outperforms heuristic model, (v) as expected the rule-based model holds more inventory than the optimization model.

A Buffer Management Issue in Designing SSDs for LFSs

Science.gov (United States)

Kim, Jaegeuk; Seol, Jinho; Maeng, Seungryoul

This letter introduces a buffer management issue in designing SSDs for log-structured file systems (LFSs). We implemented a novel trace-driven SSD simulator in SystemC language, and simulated several SSD architectures with the NILFS2 trace. From the results, we give two major considerations related to the buffer management as follows. (1) The write buffer is used as a buffer not a cache, since all write requests are sequential in NILFS2. (2) For better performance, the main architectural factor is the bus bandwidth, but 332MHz is enough. Instead, the read buffer makes a key role in performance improvement while caching data. To enhance SSDs, accordingly, it is an effective way to make efficient read buffer management policies, and one of the examples is tracking the valid data zone in NILFS2, which can increase the data hit ratio in read buffers significantly.

Agarose electrophoresis of DNA in discontinuous buffers, using a horizontal slab apparatus and a buffer system with improved properties.

Science.gov (United States)

Zsolnai, A; Orbán, L; Chrambach, A

1993-03-01

Using a horizontal slab apparatus with a buffer in the reservoirs at the level of the gel ("sea-level electrophoresis"), the retrograde discontinuous buffer system reported by Wiltfang et al. for sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) of proteins was applied to DNA electrophoresis. This application yielded the advantages of an increased displacement rate of the moving boundary front and a decrease in the concentration of the counterion base in the resolving phase, which yielded reduced relative mobility values at equivalent gel concentrations and practicable low buffer concentrations. The change of relative mobilities (Rf) with a variation of field strength is decreased compared to that of the migration rate in the continuous Tris-boric-acid-EDTA (TBE) buffer and thus the robustness of the system is improved, as well as the efficiency of separation. The system of Wiltfang et al. has in common with previously described discontinuous DNA system, that it is able to stack DNA from dilute samples and is insensitive to sample components with lower net mobilities than DNA, such as acetate. However, the variance of Rf at constant current density in the discontinuous buffer system is not improved over that of the migration rate at constant field strength in the continuous TBE buffer.

Managing Multiuser Database Buffers Using Data Mining Techniques

NARCIS (Netherlands)

Feng, L.; Lu, H.J.

2004-01-01

In this paper, we propose a data-mining-based approach to public buffer management for a multiuser database system, where database buffers are organized into two areas – public and private. While the private buffer areas contain pages to be updated by particular users, the public

solution growth and characterization of copper oxide thin films ...

African Journals Online (AJOL)

Thin films of copper oxide (CuO) were grown on glass slides by using the solution growth technique. Copper cloride (CuCl ) and potassium telluride (K T O ) were used. Buffer 2 2e 3 solution was used as complexing agent. The solid state properties and optical properties were obtained from characterization done using PYE ...

Buffer Zone Requirements for Soil Fumigant Applications

Science.gov (United States)

Updated pesticide product labels require fumigant users to establish a buffer zone around treated fields to reduce risks to bystanders. Useful information includes tarp testing guidance and a buffer zone calculator.

Shock buffer for nuclear control assembly

International Nuclear Information System (INIS)

Bevilacqua, F.

1977-01-01

A shock buffer is provided for the gradual deceleration of a rapidly descending control element assembly in a nuclear reactor. The interactive buffer components are associated respectively with the movable control element assembly and part of the upper guide structure independent of and spaced from the fuel assemblies of the reactor

ZnS/Zn(O,OH)S-based buffer layer deposition for solar cells

Science.gov (United States)

Bhattacharya, Raghu N [Littleton, CO

2009-11-03

The invention provides CBD ZnS/Zn(O,OH)S and spray deposited ZnS/Zn(O,OH)S buffer layers prepared from a solution of zinc salt, thiourea and ammonium hydroxide dissolved in a non-aqueous/aqueous solvent mixture or in 100% non-aqueous solvent. Non-aqueous solvents useful in the invention include methanol, isopropanol and triethyl-amine. One-step deposition procedures are described for CIS, CIGS and other solar cell devices.

Deflating link buffers in a wireless mesh network

KAUST Repository

Jamshaid, Kamran; Shihada, Basem; Showail, Ahmad; Levis, Philip

2014-01-01

We analyze the problem of buffer sizing for backlogged TCP flows in 802.11-based wireless mesh networks. Our objective is to maintain high network utilization while providing low queueing delays. Unlike wired networks where a single link buffer feeds a bottleneck link, the radio spectral resource in a mesh network is shared among a set of contending mesh routers. We account for this by formulating the buffer size problem as sizing a collective buffer distributed over a set of interfering nodes. In this paper we propose mechanisms for sizing and distributing this collective buffer among the mesh nodes constituting the network bottleneck. Our mechanism factors in the network topology and wireless link rates, improving on pre-set buffer allocations that cannot optimally work across the range of configurations achievable with 802.11 radios. We evaluate our mechanisms using simulations as well as experiments on a testbed. Our results show that we can reduce the RTT of a flow by 6× or more, at the cost of less than 10% drop in end-to-end flow throughput.

Deflating link buffers in a wireless mesh network

KAUST Repository

Jamshaid, Kamran

2014-05-01

We analyze the problem of buffer sizing for backlogged TCP flows in 802.11-based wireless mesh networks. Our objective is to maintain high network utilization while providing low queueing delays. Unlike wired networks where a single link buffer feeds a bottleneck link, the radio spectral resource in a mesh network is shared among a set of contending mesh routers. We account for this by formulating the buffer size problem as sizing a collective buffer distributed over a set of interfering nodes. In this paper we propose mechanisms for sizing and distributing this collective buffer among the mesh nodes constituting the network bottleneck. Our mechanism factors in the network topology and wireless link rates, improving on pre-set buffer allocations that cannot optimally work across the range of configurations achievable with 802.11 radios. We evaluate our mechanisms using simulations as well as experiments on a testbed. Our results show that we can reduce the RTT of a flow by 6× or more, at the cost of less than 10% drop in end-to-end flow throughput.

Design, production and initial state of the buffer

Energy Technology Data Exchange (ETDEWEB)

Boerjesson, Lennart; Gunnarsson, David; Johannesson, Lars-Erik; Jonsson, Esther

2010-12-15

The report is included in a set of Production reports, presenting how the KBS-3 repository is designed, produced and inspected. The set of reports is included in the safety report for the KBS-3 repository and repository facility. The report provides input on the initial state of the buffer for the assessment of the long-term safety, SR-Site. The initial state refers to the properties of the engineered barriers once they have been finally placed in the KBS-3 repository and will not be further handled within the repository facility. In addition, the report provides input to the operational safety report, SR-Operation, on how the buffer shall be handled and installed. The report presents the design premises and reference design of the buffer and verifies the conformity of the reference design to the design premises. It also describes the production of the buffer, from excavation and delivery of buffer material to installation in the deposition hole. Finally, the initial state of the buffer and its conformity to the reference design and design premises is presented

Experimental determination of the hydrothermal solubility of ReS2 and the Re–ReO2 buffer assemblage and transport of rhenium under supercritical conditions

Directory of Open Access Journals (Sweden)

Wood Scott A

2002-01-01

Full Text Available To understand the aqueous species important for transport of rhenium under supercritical conditions, we conducted a series of solubility experiments on the Re–ReO2 buffer assemblage and ReS2. In these experiments, pH was buffered by the K–feldspar–muscovite–quartz assemblage; in sulfur-free systems was buffered by the Re–ReO2 assemblage; and and in sulfur-containing systems were buffered by the magnetite–pyrite–pyrrhotite assemblage. Our experimental studies indicate that the species ReCl40 is dominant at 400°C in slightly acidic to near-neutral, and chloride-rich (total chloride concentrations ranging from 0.5 to 1.0 M environments, and ReCl3+ may predominate at 500°C in a solution with total chloride concentrations ranging from 0.5 to 1.5 M. The results also demonstrate that the solubility of ReS2 is about two orders of magnitude less than that of ReO2. This finding not only suggests that ReS2 (or a ReS2 component in molybdenite is the solubility-controlling phase in sulfur-containing, reducing environments but also implies that a mixing process involving an oxidized, rhenium-containing solution and a solution with reduced sulfur is one of the most effective mechanisms for deposition of rhenium. In analogy with Re, TcS2 may be the stable Tc-bearing phase in deep geological repositories of radioactive wastes.

Urban Runoff: Model Ordinances for Aquatic Buffers

Science.gov (United States)

Aquatic Buffers serve as natural boundaries between local waterways and existing development. The model and example ordinaces below provide suggested language or technical guidance designed to create the most effective stream buffer zones possible.

Heed the head: buffer benefits along headwater streams

Science.gov (United States)

Rhonda Mazza; Deanna (Dede) Olson

2015-01-01

Since the Northwest Forest Plan implemented riparian buffers along non-fish bearing streams in 1994, there have been questions about how wide those buffers need to be to protect aquatic and riparian resources from upland forest management activities. The Density Management and Riparian Buffer Study of western Oregon, also initiated in 1994, examines the effects of...

Investigation into the temporal stability of aqueous standard solutions of psilocin and psilocybin using high performance liquid chromatography.

Science.gov (United States)

Anastos, N; Barnett, N W; Pfeffer, F M; Lewis, S W

2006-01-01

This paper reports an investigation into the temporal stability of aqueous solutions of psilocin and psilocybin reference drug standards over a period of fourteen days. This study was performed using high performance liquid chromatography utilising a (95:5% v/v) methanol: 10 mM ammonium formate, pH 3.5 mobile phase and absorption detection at 269 nm. It was found that the exclusion of light significantly prolonged the useful life of standards, with aqueous solutions of both psilocin and psilocybin being stable over a period of seven days.

SPARC: Demonstrate burst-buffer-based checkpoint/restart on ATS-1.

Energy Technology Data Exchange (ETDEWEB)

Oldfield, Ron A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Ulmer, Craig D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Widener, Patrick [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Ward, H. Lee [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2018-01-01

Recent high-performance computing (HPC) platforms such as the Trinity Advanced Technology System (ATS-1) feature burst buffer resources that can have a dramatic impact on an application’s I/O performance. While these non-volatile memory (NVM) resources provide a new tier in the storage hierarchy, developers must find the right way to incorporate the technology into their applications in order to reap the benefits. Similar to other laboratories, Sandia is actively investigating ways in which these resources can be incorporated into our existing libraries and workflows without burdening our application developers with excessive, platform-specific details. This FY18Q1 milestone summaries our progress in adapting the Sandia Parallel Aerodynamics and Reentry Code (SPARC) in Sandia’s ATDM program to leverage Trinity’s burst buffers for checkpoint/restart operations. We investigated four different approaches with varying tradeoffs in this work: (1) simply updating job script to use stage-in/stage out burst buffer directives, (2) modifying SPARC to use LANL’s hierarchical I/O (HIO) library to store/retrieve checkpoints, (3) updating Sandia’s IOSS library to incorporate the burst buffer in all meshing I/O operations, and (4) modifying SPARC to use our Kelpie distributed memory library to store/retrieve checkpoints. Team members were successful in generating initial implementation for all four approaches, but were unable to obtain performance numbers in time for this report (reasons: initial problem sizes were not large enough to stress I/O, and SPARC refactor will require changes to our code). When we presented our work to the SPARC team, they expressed the most interest in the second and third approaches. The HIO work was favored because it is lightweight, unobtrusive, and should be portable to ATS-2. The IOSS work is seen as a long-term solution, and is favored because all I/O work (including checkpoints) can be deferred to a single library.

Establishing the traceability of a uranyl nitrate solution to a standard reference material

International Nuclear Information System (INIS)

Jackson, C.H.; Clark, J.P.

1978-01-01

A uranyl nitrate solution for use as a Working Calibration and Test Material (WCTM) was characterized, using a statistically designed procedure to document traceability to National Bureau of Standards Reference Material (SPM-960). A Reference Calibration and Test Material (PCTM) was prepared from SRM-960 uranium metal to approximate the acid and uranium concentration of the WCTM. This solution was used in the characterization procedure. Details of preparing, handling, and packaging these solutions are covered. Two outside laboratories, each having measurement expertise using a different analytical method, were selected to measure both solutions according to the procedure for characterizing the WCTM. Two different methods were also used for the in-house characterization work. All analytical results were tested for statistical agreement before the WCTM concentration and limit of error values were calculated. A concentration value was determined with a relative limit of error (RLE) of approximately 0.03% which was better than the target RLE of 0.08%. The use of this working material eliminates the expense of using SRMs to fulfill traceability requirements for uranium measurements on this type material. Several years' supply of uranyl nitrate solution with NBS traceability was produced. The cost of this material was less than 10% of an equal quantity of SRM-960 uranium metal

Z-buffer image assembly processing in high parallel visualization processing

International Nuclear Information System (INIS)

Kaneko, Isamu; Muramatsu, Kazuhiro

2000-03-01

On the platform of the parallel computer with many processors, the domain decomposition method is used as a popular means of parallel processing. In these days when the simulation scale becomes much larger and takes a lot of time, the simultaneous visualization processing with the actual computation is much more needed, and especially in case of a real-time visualization, the domain decomposition technique is indispensable. In case of parallel rendering processing, the rendered results must be gathered to one processor to compose the integrated picture in the last stage. This integration is usually conducted by the method using Z-buffer values. This process, however, induces the crucial problems of much lower speed processing and local memory shortage in case of parallel processing exceeding more than several tens of processors. In this report, the two new solutions are proposed. The one is the adoption of a special operator (Reduce operator) in the parallelization process, and the other is a buffer compression by deleting the background informations. This report includes the performance results of these new techniques to investigate their effect with use of the parallel computer Paragon. (author)

On Buffer-Aided Multiple-Access Relay Channel

DEFF Research Database (Denmark)

Liu, Rongkuan; Popovski, Petar; Wang, Gang

2016-01-01

This letter treats uplink scenario where M user equipments (UEs) send to a base station (BS), possibly via a common relay station (RS) that is equipped with a buffer. This is a multiple-access relay channel aided by a buffer. We devise a protocol in which the transmission mode is selected...... entirely at the BS, while simultaneously a number of UEs sends new messages to the BS. The results show that the adaptive selection of direct and buffer-aided relay transmissions leads to significant average throughput gains....

DNA amplification fingerprinting using 10 x polymerase chain reaction buffer with ammonium sulfate for human identification

International Nuclear Information System (INIS)

Baransel, Asyun; Dugler, Hikmat E.; Tokdemir, Mehmet

2004-01-01

The polymerase chain reaction (PCR) - based DNA amplification fingerprinting (DAF) or randomly amplified polymorphic DNA (RAPD) is based on a strategy using a single arbitrary oligonucleotide primer to generate anonymous amplification of genomic DNA. On this basic strategy, in this study, we aimed to test individual differences and usefulness of 2 basic primers (5-CGCGCCGG-3 and 5-TGCCGAGCTG-3) and examined whether there is a positive effect on results of 10 x PCR buffer with ammonium sulfate. A new approach in DNA fingerprinting, 10 x PCR buffer with ammonium sulfate, is presented in the study. Primers with single 8 and 10 nucleotides in length and 2 different PCR buffers with or without ammonium sulfate were used to identify 135 volunteers with no blood relationship. This study was carried out at the Pharmacology Laboratory, University of Gaziantep, School of Medicine, Turkey between 1999 and 2000. An average of 10 major bands representing 500-1500 base pair (bp) in length was determined as amplified DNA products on standard agarose gels for these volunteers. The use of ammonium sulfate in 10 x PCR buffers has increased to 92% success ratio of individual difference obtained from the 8 nucleotides primer. With this study, more reliable results can be obtained by using ammonium sulfate in 10 x PCR buffers. (author)

Phosphorus retention in riparian buffers: review of their efficiency.

Science.gov (United States)

Hoffmann, Carl Christian; Kjaergaard, Charlotte; Uusi-Kämppä, Jaana; Hansen, Hans Christian Bruun; Kronvang, Brian

2009-01-01

Ground water and surface water interactions are of fundamental importance for the biogeochemical processes governing phosphorus (P) dynamics in riparian buffers. The four most important conceptual hydrological pathways for P losses from and P retention in riparian buffers are reviewed in this paper: (i) The diffuse flow path with ground water flow through the riparian aquifer, (ii) the overland flow path across the riparian buffer with water coming from adjacent agricultural fields, (iii) irrigation of the riparian buffer with tile drainage water from agricultural fields where disconnected tile drains irrigate the riparian buffer, and (iv) inundation of the riparian buffer (floodplain) with river water during short or longer periods. We have examined how the different flow paths in the riparian buffer influence P retention mechanisms theoretically and from empirical evidence. The different hydrological flow paths determine where and how water-borne P compounds meet and interact with iron and aluminum oxides or other minerals in the geochemical cycling of P in the complex and dynamic environment that constitutes a riparian buffer. The main physical process in the riparian buffer-sedimentation-is active along several flow paths and may account for P retention rates of up to 128 kg P ha(-1) yr(-1), while plant uptake may temporarily immobilize up to 15 kg P ha(-1) yr(-1). Retention of dissolved P in riparian buffers is not as pronounced as retention of particulate P and is often below 0.5 kg P ha(-1) yr(-1). Several studies show significant release of dissolved P (i.e., up to 8 kg P ha(-1) yr(-1)).

Preformulation study of methazolamide for topical ophthalmic delivery: physicochemical properties and degradation kinetics in aqueous solutions.

Science.gov (United States)

Jiang, Sunmin; Wang, Fengzhen; Zhu, Shuning; Zhang, Xiumei; Guo, Zhigang; Li, Rui; Xu, Qunwei

2013-05-20

Methazolamide (MTZ) is an anti-glaucoma drug. The present paper aims to characterize the physicochemical properties and degradation kinetics of MTZ to provide a basis for topical ophthalmic delivery. With the increase in pH (pH 5.5-8.0) of aqueous solution, the solubility of the compound increased while the partition coefficient (Ko/w) which was estimated in the system n-octanol/aqueous solution decreased. The degradation of MTZ in aqueous solution followed pseudo-first-order kinetic. The degradation rate kpH is the rate in the absence of buffer catalysis. Plotting the natural logarithm of kpH versus the corresponding pH value gave a V-shaped pH-rate profile with a maximum stability at pH 5.0. The degradation rate constants as a function of the temperature obeyed the Arrhenius equation (R(2)=0.9995 at pH 7.0 and R(2)=0.9955 at pH 9.0, respectively). A decrease in ionic strength and buffer concentration displayed a stabilizing effect on MTZ. Buffer species also influenced the MTZ hydrolysis. Phosphate buffer system was more catalytic than tris and borate buffer systems. In brief, it is important to consider the physicochemical properties and the stability of MTZ during formulation. Copyright © 2013 Elsevier B.V. All rights reserved.

The Interplay between Feedback and Buffering in Cellular Homeostasis.

Science.gov (United States)

Hancock, Edward J; Ang, Jordan; Papachristodoulou, Antonis; Stan, Guy-Bart

2017-11-22

Buffering, the use of reservoirs of molecules to maintain concentrations of key molecular species, and negative feedback are the primary known mechanisms for robust homeostatic regulation. To our knowledge, however, the fundamental principles behind their combined effect have not been elucidated. Here, we study the interplay between buffering and negative feedback in the context of cellular homeostasis. We show that negative feedback counteracts slow-changing disturbances, whereas buffering counteracts fast-changing disturbances. Furthermore, feedback and buffering have limitations that create trade-offs for regulation: instability in the case of feedback and molecular noise in the case of buffering. However, because buffering stabilizes feedback and feedback attenuates noise from slower-acting buffering, their combined effect on homeostasis can be synergistic. These effects can be explained within a traditional control theory framework and are consistent with experimental observations of both ATP homeostasis and pH regulation in vivo. These principles are critical for studying robustness and homeostasis in biology and biotechnology. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

Inactivation of Biological Agents Using Neutral Oxone-Chloride Solutions

National Research Council Canada - National Science Library

Delcomyn, Carrie A; Bushway, Karen E; Henley, Michael V

2006-01-01

... to contaminated equipment or terrain. A neutral, bicarbonate-buffered aqueous solution of Oxone and sodium chloride that rapidly generates hypochlorite and hypochlorous acid in situ was evaluated as a new alternative to bleach...

Methods for improved growth of group III nitride buffer layers

Science.gov (United States)

Melnik, Yurity; Chen, Lu; Kojiri, Hidehiro

2014-07-15

Methods are disclosed for growing high crystal quality group III-nitride epitaxial layers with advanced multiple buffer layer techniques. In an embodiment, a method includes forming group III-nitride buffer layers that contain aluminum on suitable substrate in a processing chamber of a hydride vapor phase epitaxy processing system. A hydrogen halide or halogen gas is flowing into the growth zone during deposition of buffer layers to suppress homogeneous particle formation. Some combinations of low temperature buffers that contain aluminum (e.g., AlN, AlGaN) and high temperature buffers that contain aluminum (e.g., AlN, AlGaN) may be used to improve crystal quality and morphology of subsequently grown group III-nitride epitaxial layers. The buffer may be deposited on the substrate, or on the surface of another buffer. The additional buffer layers may be added as interlayers in group III-nitride layers (e.g., GaN, AlGaN, AlN).

Main-Memory Operation Buffering for Efficient R-Tree Update

DEFF Research Database (Denmark)

Jensen, Christian Søndergaard; Saltenis, Simonas; Biveinis, Laurynas

2007-01-01

the buffering of update operations in main memory as well as the grouping of operations to reduce disk I/O. In particular, operations are performed in bulk so that multiple operations are able to share I/O. The paper presents an analytical cost model that is shown to be accurate by empirical studies...... the main memory that is indeed available, or do not support some of the standard index operations. Assuming a setting where the index updates need not be written to disk immediately, we propose an R-tree-based indexing technique that does not exhibit any of these drawbacks. This technique exploits...

Addition of urea and thiourea to electrophoresis sample buffer improves efficiency of protein extraction from TCA/acetone-treated smooth muscle tissues for phos-tag SDS-PAGE.

Science.gov (United States)

Takeya, Kosuke; Kaneko, Toshiyuki; Miyazu, Motoi; Takai, Akira

2018-01-01

Phosphorylation analysis by using phos-tag technique has been reported to be suitable for highly sensitive quantification of smooth muscle myosin regulatory light chain (LC 20 ) phosphorylation. However, there is another factor that will affect the sensitivity of phosphorylation analysis, that is, protein extraction. Here, we optimized the conditions for total protein extraction out of trichloroacetic acid (TCA)-fixed tissues. Standard SDS sample buffer extracted less LC 20 , actin and myosin phosphatase targeting subunit 1 (MYPT1) from TCA/acetone treated ciliary muscle strips. On the other hand, sample buffer containing urea and thiourea in addition to lithium dodecyl sulfate (LDS) or SDS extracted those proteins more efficiently, and thus increased the detection sensitivity up to 4-5 fold. Phos-tag SDS-PAGE separated dephosphorylated and phosphorylated LC 20 s extracted in LDS/urea/thiourea sample buffer to the same extent as those in standard SDS buffer. We have concluded that LDS (or SDS) /urea/thiourea sample buffer is suitable for highly sensitive phosphorylation analysis in smooth muscle, especially when it is treated with TCA/acetone. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Mechanisms of social buffering of fear in zebrafish.

Science.gov (United States)

Faustino, Ana I; Tacão-Monteiro, André; Oliveira, Rui F

2017-03-31

Some humans thrive whereas others resign when exposed to threatening situations throughout life. Social support has been identified as an important modulator of these discrepancies in human behaviour, and other social animals also exhibit phenomena in which individuals recover better from aversive events when conspecifics are present - aka social buffering. Here we studied social buffering in zebrafish, by exposing focal fish to an aversive stimulus (alarm substance - AS) either in the absence or presence of conspecific cues. When exposed to AS in the presence of both olfactory (shoal water) and visual (sight of shoal) conspecific cues, focal fish exhibited a lower fear response than when tested alone, demonstrating social buffering in zebrafish. When separately testing each cue's effectiveness, we verified that the visual cue was more effective than the olfactory in reducing freezing in a persistent threat scenario. Finally, we verified that social buffering was independent of shoal size and coincided with a distinct pattern of co-activation of brain regions known to be involved in mammalian social buffering. Thus, this study suggests a shared evolutionary origin for social buffering in vertebrates, bringing new evidence on the behavioural, sensory and neural mechanisms underlying this phenomenon.

Evaluation on elution feature of bentonite buffer materials

Energy Technology Data Exchange (ETDEWEB)

Ishikawa, Hirohisa; Kanno, Takeshi; Matsumoto, Kazuhiro

1997-09-01

In order to evaluate long term physical stability of artificial barrier in land disposal of high level radioactive wastes, it is necessary to know quantitatively elution behavior of buffering materials from disposal road (or cavity) to circumferential rock crack. When elution of the buffer material occurs on large scale, amount of bentonite in the disposal road (or cavity) reduces and reduction of various functions expected to the buffer materials is presumed. According to specification examples of road transverse arrangement and disposal vertical arrangement systems, evaluation on elution amount of the buffer materials at disposal environment was conducted. Opening width of rock crack in the disposal environment was supposed to be 0.5 mm. As a result, obtained mass elution ratios of the buffer materials due to extrusion phenomenon were 0.04 to 0.2% after 10,000 year and 2 to 12% after 1,000,000 years. (G.K.)

Primary standardization of a {sup 177}Lu solution; Padronizacao primaria de uma solucao de {sup 177}Lu

Energy Technology Data Exchange (ETDEWEB)

Iwahara, Akira; Silva, Carlos Jose da; Tauhata, Luiz; Oliveira, Estela Maria de, E-mail: iwahara@ird.gov.b, E-mail: carlos@ird.gov.b, E-mail: tauhata@ird.gov.b, E-mail: estela@ird.gov.b [Instituto de Radioprotecao e Dosimetria (IRD/CNEN-RJ), Rio de Janeiro, RJ (Brazil); Rezende, Eduarda Alexandre, E-mail: eduarda@ird.gov.b [Centro Federal de Educacao Tecnologica de Quimica (CEFET), Nilopolis, RJ (Brazil)

2009-07-01

For the purpose to make available reliable standards of {sup 177}Lu to the users and producers, a radionuclide solution was standardized using the primary methods of coincidence 4{pi}{beta}(PC)-{gamma}(NaI(Tl)) and of 4{pi}{beta}(LS)-{gamma}(NaI(Tl)). The results presented a convergence in the range of evaluated uncertainties. The standard uncertainties were of the 0.50 and 0.74% for the anticoincidence and coincidence respectively

Influence of material and solution composition on the extrusion/erosion behaviour of compacted bentonite

International Nuclear Information System (INIS)

Schatz, Timothy; Martikainen, Jari; Koskinen, Kari

2010-01-01

Document available in extended abstract form only. In principle, in a KBS-3 type repository, the volume of a deposition hole is fixed and the bentonite buffer mass accordingly balanced to lead to the development of a suitable swelling pressure upon saturation. However, fractures intersecting the deposition holes give rise to the possibility that volume constrained conditions do not universally exist. Such fractures may provide pathways for the continued, localised, free swelling of bentonite buffer material. Loss of mass from the deposition hole by extrusion into intersecting fractures may compromise the long-term safety and performance of the buffer component of the engineered barrier system. Furthermore, the continued hydration and expansion of extruded bentonite in these fracture environments could lead to the separation of colloid-sized (or larger) particles by diffusion or shear which may have to be accounted for in possible radionuclide migration scenarios. Geochemical conditions, with respect to both solution and material composition, are considered to play important roles regarding the fracture extrusion/erosion of bentonite buffer material. For example, calcium-montmorillonite exhibits limited free swelling relative to sodium-montmorillonite and the colloidal and rheological properties of montmorillonite dispersions are sensitive to the presence of electrolytes. Insofar as both the buffer material composition (due to ion exchange) and groundwater composition (dilution resulting from infiltration of glacial melt water) are expected to evolve with time, so too might the potential for fracture extrusion/erosion of buffer material vary over time. The hydraulic characteristics of the intersecting fracture are expected to influence the extrusion/erosion process as well. To evaluate the effect of material and solution composition on the potential for extrusion of buffer mass into intersecting fractures, a series of batch experiments were performed. In these

Visualization of Buffer Capacity with 3-D "Topo" Surfaces: Buffer Ridges, Equivalence Point Canyons and Dilution Ramps

Science.gov (United States)

Smith, Garon C.; Hossain, Md Mainul

2016-01-01

BufCap TOPOS is free software that generates 3-D topographical surfaces ("topos") for acid-base equilibrium studies. It portrays pH and buffer capacity behavior during titration and dilution procedures. Topo surfaces are created by plotting computed pH and buffer capacity values above a composition grid with volume of NaOH as the x axis…

Passivity of 316L stainless steel in borate buffer solution studied by Mott-Schottky analysis, atomic absorption spectrometry and X-ray photoelectron spectroscopy

International Nuclear Information System (INIS)

Feng Zhicao; Cheng Xuequn; Dong Chaofang; Xu Lin; Li Xiaogang

2010-01-01

Research highlights: → The polarization curve of 316L SS possesses five turning potentials in passive region. → Films formed at turning potentials perform different electrochemical and semiconductor properties. → Dissolutions and regenerations of passive film at turning potentials are obtained by AAS and XPS. → Turning potentials appearing in passive region are ascribed to the changes of the compositions of the passive films. - Abstract: The passivity of 316L stainless steel in borate buffer solution has been investigated by Mott-Schottky, atomic absorption spectrometry (AAS) and X-ray photoelectron spectroscopy (XPS). The results indicate that the polarization curve in the passive region possesses several turning potentials (0 V SCE , 0.2 V SCE , 0.4 V SCE , 0.6 V SCE and 0.85 V SCE ). The passive films formed at turning potentials perform different electrochemical and semiconductor properties. Further, the compositions of the passive films formed at turning potentials are investigated. The results reasonably explain why these potentials appear in the passive region and why specimens perform different properties at turning potentials.

Novel nuclei isolation buffer for flow cytometric genome size estimation of Zingiberaceae: a comparison with common isolation buffers.

Science.gov (United States)

Sadhu, Abhishek; Bhadra, Sreetama; Bandyopadhyay, Maumita

2016-11-01

Cytological parameters such as chromosome numbers and genome sizes of plants are used routinely for studying evolutionary aspects of polyploid plants. Members of Zingiberaceae show a wide range of inter- and intrageneric variation in their reproductive habits and ploidy levels. Conventional cytological study in this group of plants is severely hampered by the presence of diverse secondary metabolites, which also affect their genome size estimation using flow cytometry. None of the several nuclei isolation buffers used in flow cytometry could be used very successfully for members of Zingiberaceae to isolate good quality nuclei from both shoot and root tissues. The competency of eight nuclei isolation buffers was compared with a newly formulated buffer, MB01, in six different genera of Zingiberaceae based on the fluorescence intensity of propidium iodide-stained nuclei using flow cytometric parameters, namely coefficient of variation of the G 0 /G 1 peak, debris factor and nuclei yield factor. Isolated nuclei were studied using fluorescence microscopy and bio-scanning electron microscopy to analyse stain-nuclei interaction and nuclei topology, respectively. Genome contents of 21 species belonging to these six genera were determined using MB01. Flow cytometric parameters showed significant differences among the analysed buffers. MB01 exhibited the best combination of analysed parameters; photomicrographs obtained from fluorescence and electron microscopy supported the superiority of MB01 buffer over other buffers. Among the 21 species studied, nuclear DNA contents of 14 species are reported for the first time. Results of the present study substantiate the enhanced efficacy of MB01, compared to other buffers tested, in the generation of acceptable cytograms from all species of Zingiberaceae studied. Our study facilitates new ways of sample preparation for further flow cytometric analysis of genome size of other members belonging to this highly complex polyploid family

The stochastic nuclide transport model for buffer/backfill materials

International Nuclear Information System (INIS)

Ma Liping; Han Yongguo

2014-01-01

Currently, study on nuclide migration law in geological disposal repository of high level waste is assumed buffer/backfill layer to be continuous medium, utilized the continuity equation, equation of state, the equations of motion, etc, formed a set of theory and method to estimate nuclide concentration distribution in buffer/backfill layer, and provided an important basis for nuclide migration rules of repository. However, it is necessary to study the buffer/backfill layer microstructure and subtly describe the pore structure and fracture system of the buffer/backfill layer, and reflect the changes in connectivity and in different directions of the buffer/backfill layer. Through using random field theory, the nuclide transport for the buffer/backfill layer in geological disposal repository of nuclear waste is described in the paper. This paper mainly includes that, t represents the time, ξ t ⊂ Z d = d represents the integer lattice, Z represents collectivity integers, d = l, 2, 3, for instance, d = 2, Z d = {(m, n) : m, n ∈ Z} the state point of ξ t is typically considered to be occupied by the nuclide concentration values of the buffer/backfill layer, ξ t also represents random set in the diagram of two dimensional integer lattice, namely, t ∈ [0, T], {ξ t ,0 ≤ t ≤ ⊂ T} Consequently, according to the stochastic process obtained above, the changes of the nuclide concentration values of the buffer/backfill layer or the buffer/backfill laboratory materials in the repository with the time can be known. (authors)

Buffer Zone, Nicosia

OpenAIRE

Sorensen, Marie Louise

2010-01-01

Images of the United Nations Buffer Zone or Green Line which has partitioned Cyprus since 1974 The research leading to these results has received funding from the European Community's Seventh Framework Programme [FP7/2007-2013] under grant agreement n° 217411.

Grass buffers for playas in agricultural landscapes: An annotated bibliography

Science.gov (United States)

Melcher, Cynthia P.; Skagen, Susan K.

2005-01-01

This bibliography and associated literature synthesis (Melcher and Skagen, 2005) was developed for the Playa Lakes Joint Venture (PLJV). The PLJV sought compilation and annotation of the literature on grass buffers for protecting playas from runoff containing sediments, nutrients, pesticides, and other contaminants. In addition, PLJV sought information regarding the extent to which buffers may attenuate the precipitation runoff needed to fill playas, and avian use of buffers. We emphasize grass buffers, but we also provide information on other buffer types.

Thermo-Hydraulic Modelling of Buffer and Backfill

International Nuclear Information System (INIS)

Pintado, X.; Rautioaho, E.

2013-09-01

The temporal evolution of saturation, liquid pressure and temperature in the components of the engineered barrier system was studied using numerical methods. A set of laboratory tests was conducted to calibrate the parameters employed in the models. The modelling consisted of thermal, hydraulic and thermo-hydraulic analysis in which the significant thermo-hydraulic processes, parameters and features were identified. CODE B RIGHT was used for the finite element modelling and supplementary calculations were conducted with analytical methods. The main objective in this report is to improve understanding of the thermo-hydraulic processes and material properties that affect buffer behaviour in the Olkiluoto repository and to determine the parametric requirements of models for the accurate prediction of this behaviour. The analyses consisted of evaluating the influence of initial canister temperature and gaps in the buffer, and the role played by fractures and the rock mass located between fractures in supplying water for buffer and backfill saturation. In the thermo-hydraulic analysis, the primary processes examined were the effects of buffer drying near the canister on temperature evolution and the manner in which heat flow affects the buffer saturation process. Uncertainties in parameters and variations in the boundary conditions, modelling geometry and thermo-hydraulic phenomena were assessed with a sensitivity analysis. The material parameters, constitutive models, and assumptions made were carefully selected for all the modelling cases. The reference parameters selected for the simulations were compared and evaluated against laboratory measurements. The modelling results highlight the importance of understanding groundwater flow through the rock mass and from fractures in the rock in order to achieve reliable predictions regarding buffer saturation, since saturation times could range from a few years to tens of thousands of years depending on the hydrogeological

The buffer/container experiment design and construction report

Energy Technology Data Exchange (ETDEWEB)

Chandler, N.A.; Wan, A.W.L.; Roach, P.J

1998-03-01

The Buffer/Container Experiment was a full-scale in situ experiment, installed at a depth of 240 m in granitic rock at AECL's Underground Research Laboratory (URL). The experiment was designed to examine the performance of a compacted sand-bentonite buffer material under the influences of elevated temperature and in situ moisture conditions. Buffer material was compacted in situ into a 5-m-deep, 1.24-m-diameter borehole drilled into the floor of an excavation. A 2.3-m long heater, representative of a nuclear fuel waste container, was placed within the buffer, and instrumentation was installed to monitor changes in buffer moisture conditions, temperature and stress. The experiment was sealed at the top of the borehole and restrained against vertical displacement. Instrumentation in the rock monitored pore pressures, temperatures and rock displacement. The heater was operated at a constant power of 1200 W, which provided a heater skin temperature of approximately 85 degrees C. Experiment construction and installation required two years, followed by two and a half years of heater operation and two years of monitoring the rock conditions during cooling. The construction phase of the experiment included the design, construction and testing of a segmental heater and controller, geological and hydrogeological characterization of the rock, excavation of the experiment room, drilling of the emplacement borehole using high pressure water, mixing and in situ compaction of buffer material, installation of instrumentation in the rock, buffer and on the heater, and the construction of concrete curb and steel vertical restraint system at the top of emplacement borehole. Upon completion of the experiment, decommissioning sampling equipment was designed and constructed and sampling methods were developed which allowed approximately 2000 samples of buffer material to be taken over a 12-day period. Quality assurance procedures were developed for all aspects of experiment

The buffer/container experiment design and construction report

International Nuclear Information System (INIS)

Chandler, N.A.; Wan, A.W.L.; Roach, P.J.

1998-03-01

The Buffer/Container Experiment was a full-scale in situ experiment, installed at a depth of 240 m in granitic rock at AECL's Underground Research Laboratory (URL). The experiment was designed to examine the performance of a compacted sand-bentonite buffer material under the influences of elevated temperature and in situ moisture conditions. Buffer material was compacted in situ into a 5-m-deep, 1.24-m-diameter borehole drilled into the floor of an excavation. A 2.3-m long heater, representative of a nuclear fuel waste container, was placed within the buffer, and instrumentation was installed to monitor changes in buffer moisture conditions, temperature and stress. The experiment was sealed at the top of the borehole and restrained against vertical displacement. Instrumentation in the rock monitored pore pressures, temperatures and rock displacement. The heater was operated at a constant power of 1200 W, which provided a heater skin temperature of approximately 85 degrees C. Experiment construction and installation required two years, followed by two and a half years of heater operation and two years of monitoring the rock conditions during cooling. The construction phase of the experiment included the design, construction and testing of a segmental heater and controller, geological and hydrogeological characterization of the rock, excavation of the experiment room, drilling of the emplacement borehole using high pressure water, mixing and in situ compaction of buffer material, installation of instrumentation in the rock, buffer and on the heater, and the construction of concrete curb and steel vertical restraint system at the top of emplacement borehole. Upon completion of the experiment, decommissioning sampling equipment was designed and constructed and sampling methods were developed which allowed approximately 2000 samples of buffer material to be taken over a 12-day period. Quality assurance procedures were developed for all aspects of experiment construction

Further improvements in competitive guarantees for QoS buffering

NARCIS (Netherlands)

Bansal, N.; Fleischer, L.K.; Kimbrel, T.; Mahdian, M.; Schieber, B.; Sviridenko, M.; Diaz, J.; Karhumäki, J.; Lepistö, A.; Sannella, D.

2004-01-01

We study the behavior of algorithms for buffering packets weighted by different levels of Quality of Service (QoS) guarantees in a single queue. Buffer space is limited, and packet loss occurs when the buffer overflows. We describe a modification of the previously proposed ``preemptive greedy{''}

Buffers Plus

Science.gov (United States)

Ramette, Richard W.

1998-11-01

In 1989 JCE Software published The Acid-Base Package: A Collection of Useful Programs for Proton Transfer Systems (Ramette, R. W. J. Chem. Educ. Software 1989, 2B No. 2). This DOS program has been fully upgraded by the same author to the world of Windows 95. Buffers Plus takes advantage of a modern user interface and offers many new options not possible in the original version.

Stacking and discontinuous buffers in capillary zone electrophoresis.

Science.gov (United States)

Shihabi, Z K

2000-08-01

Discontinuous buffers for capillary zone electrophoresis (CZE) can be used under less rigid conditions compared to those for isotachophoresis for stacking. They can be prepared simply by modifying the sample itself, either by addition of small inorganic ions, low conductivity diluents, or both, and also by adjusting its pH, meanwhile injecting a large volume on the capillary. Zwitterionic and organic-based buffers such as triethanolamine and tris(hydroxymethyl)aminomethane (Tris) are well suited for stacking due to their low conductivity, provided the buffer is discontinuous as demonstrated here. A simple mechanism based on discontinuous buffers is described to explain many of the observed stacking types in CZE, pointing out the many similarities to transient isotachophoresis.

Improved indexes for targeting placement of buffers of Hortonian runoff

Science.gov (United States)

M.G. Dosskey; Z. Qiu; M.J. Helmers; D.E. Eisenhauer

2011-01-01

Targeting specific locations within agricultural watersheds for installing vegetative buffers has been advocated as a way to enhance the impact of buffers and buffer programs on stream water quality. Existing models for targeting buffers of Hortonian, or infiltration-excess, runoff are not well developed. The objective was to improve on an existing soil survey–based...

A Reversible Photoacid Functioning in PBS Buffer under Visible Light.

Science.gov (United States)

Abeyrathna, Nawodi; Liao, Yi

2015-09-09

A metastable-state photoacid that can reversibly release a proton in PBS buffer (pH = 7.4) under visible light is reported. The design is based on the dual acid-base property and tautomerization of indazole. The quantum yield was as high as 0.73, and moderate light intensity (10(2) μmol·m(2)·s(-1)) is sufficient for the photoreaction. Reversible pH change of 1.7 units was demonstrated using a 0.1 mM aqueous solution. This type of photoacid is promising for control of proton-transfer processes in physiological conditions and may find applications in biomedical areas.

Design challenges and gaps in standards in developing an interoperable zero footprint DI thin client for use in image-enabled electronic health record solutions

Science.gov (United States)

Agrawal, Arun; Koff, David; Bak, Peter; Bender, Duane; Castelli, Jane

2015-03-01

The deployment of regional and national Electronic Health Record solutions has been a focus of many countries throughout the past decade. A major challenge for these deployments has been support for ubiquitous image viewing. More specifically, these deployments require an imaging solution that can work over the Internet, leverage any point of service device: desktop, tablet, phone; and access imaging data from any source seamlessly. Whereas standards exist to enable ubiquitous image viewing, few if any solutions exist that leverage these standards and meet the challenge. Rather, most of the currently available web based DI viewing solutions are either proprietary solutions or require special plugins. We developed a true zero foot print browser based DI viewing solution based on the Web Access DICOM Objects (WADO) and Cross-enterprise Document Sharing for Imaging (XDS-I.b) standards to a) demonstrate that a truly ubiquitous image viewer can be deployed; b) identify the gaps in the current standards and the design challenges for developing such a solution. The objective was to develop a viewer, which works on all modern browsers on both desktop and mobile devices. The implementation allows basic viewing functionalities of scroll, zoom, pan and window leveling (limited). The major gaps identified in the current DICOM WADO standards are a lack of ability to allow any kind of 3D reconstruction or MPR views. Other design challenges explored include considerations related to optimization of the solution for response time and low memory foot print.

Effects of buffer thickness on ATW blanket performances

International Nuclear Information System (INIS)

Yang, Won Sik

2001-01-01

This paper presents the preliminary results of target and buffer design studies for a lead-bismuth eutectic (LBE) cooled accelerator transmutation of waste (ATW) system, aimed at maximizing the source importance while simultaneously reducing the irradiation damage to fuel. Using an 840 MWt LBE cooled ATW design, the effects of buffer thickness on the blanket performances have been studied. Varying the buffer thickness for a given blanket configuration, system performances have been estimated by a series of calculations using MCNPX and REBUS-3 codes. The effects of source importance change are studied by investigating the low-energy (< 20 MeV) neutron source distribution and the equilibrium cycle blanket performance parameters such as fuel inventory, discharge burnup, burnup reactivity loss, and peak fast fluence. As the irradiation damage to fuel, the displacements per atom (dpa), hydrogen production, and helium production rates are evaluated at the buffer and blanket interface where the peak fast fluence occurs. The results show that the damage rates and the source importance increase monotonically as the buffer thickness decreases. Based on a compromise between the competing objectives of increasing the source importance and reducing the damage rates, a buffer thickness of around 20 cm appears to be reasonable

Formulation and stability of an extemporaneous 0.02% chlorhexidine digluconate ophthalmic solution.

Science.gov (United States)

Lin, Shu-Chiao; Huang, Chih-Fen; Shen, Li-Jiuan; Wang, Hsueh-Ju; Lin, Chia-Yu; Wu, Fe-Lin Lin

2015-12-01

Acanthamoeba keratitis is difficult to treat because Acanthamoeba cysts are resistant to the majority of antimicrobial agents. Despite the efficacy of 0.02% chlorhexidine in treating Acanthamoeba keratitis, a lack of data in the literature regarding the formulation's stability limits its clinical use. The objective of this study was to develop an optimal extemporaneous 0.02% chlorhexidine digluconate ophthalmic formulation for patients in need. With available active pharmaceutical ingredients, 0.02% chlorhexidine digluconate sample solutions were prepared by diluting with BSS Plus Solution or acetate buffer. Influences of the buffer, type of container, and temperature under daily-open condition were assessed based on the changes of pH values and chlorhexidine concentrations of the test samples weekly. To determine the beyond-use date, the optimal samples were stored at 2-8°C or room temperature, and analyzed at time 0 and at Week 1, Week 2, Week 3, Week 4, Week 5, Week 8, Week 12, and Week 24. Despite chlorhexidine exhibiting better stability in acetate buffer than in BSS solution, its shelf-life was stability at 2-25°C for 6 months after being sealed and for 1 month after opening. This finding will enable us to prepare 0.02% chlorhexidine digluconate ophthalmic solutions based on a doctor's prescription. Copyright © 2014. Published by Elsevier B.V.

ACETIC ACID AND A BUFFER

DEFF Research Database (Denmark)

2009-01-01

The present invention relates to a composition comprising : a) 0.01-20% wt/wt acetic acid and b) a physiologically tolerable buffer capable of maintaining acetic acid at a pH in the range of 2-7; and use of such a composition as an antimicrobial agent.......The present invention relates to a composition comprising : a) 0.01-20% wt/wt acetic acid and b) a physiologically tolerable buffer capable of maintaining acetic acid at a pH in the range of 2-7; and use of such a composition as an antimicrobial agent....

Temperature buffer test. Installation of buffer, heaters and instruments in the deposition hole

Energy Technology Data Exchange (ETDEWEB)

Johannesson, Lars-Erik; Sanden, Torbjoern; Aakesson, Mattias [Clay Technology AB, Lund (Sweden); Barcena, Ignacio; Garcia-Sineriz, Jose Luis [Aitemin, Madrid (Spain)

2010-12-15

During 2003 the Temperature Buffer Test was installed in Aespoe Hard Rock Laboratory. Temperature, water pressure, relative humidity, total pressure and displacements etc. are measured in numerous points in the test. Most of the cables from the transducers are led in the deposition hole through slots in the rock surface of the deposition hole in watertight tubes to the data collection system in a container placed in the tunnel close to the deposition hole. This report describes the work with the installations of the buffer, heaters, and instruments and yields a description of the final location of all instruments. The report also contains a description of the materials that were installed and the densities yielded after placement.

Temperature buffer test. Installation of buffer, heaters and instruments in the deposition hole

International Nuclear Information System (INIS)

Johannesson, Lars-Erik; Sanden, Torbjoern; Aakesson, Mattias; Barcena, Ignacio; Garcia-Sineriz, Jose Luis

2010-12-01

During 2003 the Temperature Buffer Test was installed in Aespoe Hard Rock Laboratory. Temperature, water pressure, relative humidity, total pressure and displacements etc. are measured in numerous points in the test. Most of the cables from the transducers are led in the deposition hole through slots in the rock surface of the deposition hole in watertight tubes to the data collection system in a container placed in the tunnel close to the deposition hole. This report describes the work with the installations of the buffer, heaters, and instruments and yields a description of the final location of all instruments. The report also contains a description of the materials that were installed and the densities yielded after placement

Retention of ionisable compounds on high-performance liquid chromatography XVII. Estimation of the pH variation of aqueous buffers with the change of the methanol fraction of the mobile phase.

Science.gov (United States)

Subirats, Xavier; Bosch, Elisabeth; Rosés, Martí

2007-01-05

The use of methanol-aqueous buffer mobile phases in HPLC is a common election when performing chromatographic separations of ionisable analytes. The addition of methanol to the aqueous buffer to prepare such a mobile phase changes the buffer capacity and the pH of the solution. In the present work, the variation of these buffer properties is studied for acetic acid-acetate, phosphoric acid-dihydrogenphosphate-hydrogenphosphate, citric acid-dihydrogencitrate-hydrogencitrate-citrate, and ammonium-ammonia buffers. It is well established that the pH change of the buffers depends on the initial concentration and aqueous pH of the buffer, on the percentage of methanol added, and on the particular buffer used. The proposed equations allow the pH estimation of methanol-water buffered mobile phases up to 80% in volume of organic modifier from initial aqueous buffer pH and buffer concentration (before adding methanol) between 0.001 and 0.01 mol L(-1). From both the estimated pH values of the mobile phase and the estimated pKa of the ionisable analytes, it is possible to predict the degree of ionisation of the analytes and therefore, the interpretation of acid-base analytes behaviour in a particular methanol-water buffered mobile phase.

Surface runoff water quality in a managed three zone riparian buffer.

Science.gov (United States)

Lowrance, Richard; Sheridan, Joseph M

2005-01-01

Managed riparian forest buffers are an important conservation practice but there are little data on the water quality effects of buffer management. We measured surface runoff volumes and nutrient concentrations and loads in a riparian buffer system consisting of (moving down slope from the field) a grass strip, a managed forest, and an unmanaged forest. The managed forest consisted of sections of clear-cut, thinned, and mature forest. The mature forest had significantly lower flow-weighted concentrations of nitrate, ammonium, total Kjeldahl N (TKN), sediment TKN, total N (nitrate + TKN), dissolved molybdate reactive P (DMRP), total P, and chloride. The average buffer represented the conditions along a stream reach with a buffer system in different stages of growth. Compared with the field output, flow-weighted concentrations of nitrate, ammonium, DMRP, and total P decreased significantly within the buffer and flow-weighted concentrations of TKN, total N, and chloride increased significantly within the buffer. All loads decreased significantly from the field to the middle of the buffer, but most loads increased from the middle of the buffer to the sampling point nearest the stream because surface runoff volume increased near the stream. The largest percentage reduction of the incoming nutrient load (at least 65% for all nutrient forms) took place in the grass buffer zone because of the large decrease (68%) in flow. The average buffer reduced loadings for all nutrient species, from 27% for TKN to 63% for sediment P. The managed forest and grass buffer combined was an effective buffer system.

Buffer construction technique using granular bentonite

International Nuclear Information System (INIS)

Masuda, Ryoichi; Asano, Hidekazu; Toguri, Satohito; Mori, Takuo; Shimura, Tomoyuki; Matsuda, Takeshi; Uyama, Masao; Noda, Masaru

2007-01-01

Buffer construction using bentonite pellets as filling material is a promising technology for enhancing the ease of repository operation. In this study, a test of such technology was conducted in a full-scale simulated disposal drift, using a filling system which utilizes a screw conveyor system. The simulated drift, which contained two dummy overpacks, was configured as a half-cross-section model with a height of 2.22 m and a length of 6.0 m. The average dry density of the buffer obtained in the test was 1.29 Mg/m 3 , with an angle of repose of 35 to 40 degrees. These test results indicate that buffer construction using a screw conveyor system for pellet emplacement in a waste disposal drift is a promising technology for repositories for high level radioactive wastes. (author)

Dynamic Buffer Capacity in Acid-Base Systems.

Science.gov (United States)

Michałowska-Kaczmarczyk, Anna M; Michałowski, Tadeusz

The generalized concept of 'dynamic' buffer capacity β V is related to electrolytic systems of different complexity where acid-base equilibria are involved. The resulting formulas are presented in a uniform and consistent form. The detailed calculations are related to two Britton-Robinson buffers, taken as examples.

Dynamic Buffer Capacity in Acid?Base Systems

OpenAIRE

Micha?owska-Kaczmarczyk, Anna M.; Micha?owski, Tadeusz

2015-01-01

The generalized concept of ?dynamic? buffer capacity ? V is related to electrolytic systems of different complexity where acid?base equilibria are involved. The resulting formulas are presented in a uniform and consistent form. The detailed calculations are related to two Britton?Robinson buffers, taken as examples.

Buffered Simulation Games for Büchi Automata

Directory of Open Access Journals (Sweden)

Milka Hutagalung

2014-05-01

Full Text Available Simulation relations are an important tool in automata theory because they provide efficiently computable approximations to language inclusion. In recent years, extensions of ordinary simulations have been studied, for instance multi-pebble and multi-letter simulations which yield better approximations and are still polynomial-time computable. In this paper we study the limitations of approximating language inclusion in this way: we introduce a natural extension of multi-letter simulations called buffered simulations. They are based on a simulation game in which the two players share a FIFO buffer of unbounded size. We consider two variants of these buffered games called continuous and look-ahead simulation which differ in how elements can be removed from the FIFO buffer. We show that look-ahead simulation, the simpler one, is already PSPACE-hard, i.e. computationally as hard as language inclusion itself. Continuous simulation is even EXPTIME-hard. We also provide matching upper bounds for solving these games with infinite state spaces.

Moisture Buffer Effect and its Impact on Indoor Environment

DEFF Research Database (Denmark)

Zhang, Mingjie; Qin, Menghao; Chen, Zhi

2017-01-01

The moisture buffer effect of building materials may have great influence on indoor hygrothermal environment. In order to characterize the moisture buffering ability of materials, the basic concept of moisture buffer value (MBV) is adopted. Firstly, a theoretical correction factor is introduced...... in this paper. The moisture uptake/release by hygroscopic materials can be calculated with the factor and the basic MBV. Furthermore, the validation of the correction factor is carried out. The impact of moisture buffering on indoor environment is assessed by using numerical simulations. The results show...

Effects of node buffer and capacity on network traffic

International Nuclear Information System (INIS)

Ling Xiang; Ding Jian-Xun; Hu Mao-Bin

2012-01-01

In this paper, we study the optimization of network traffic by considering the effects of node buffer ability and capacity. Two node buffer settings are considered. The node capacity is considered to be proportional to its buffer ability. The node effects on network traffic systems are studied with the shortest path protocol and an extension of the optimal routing [Phys. Rev. E 74 046106 (2006)]. In the diagrams of flux—density relationships, it is shown that a nodes buffer ability and capacity have profound effects on the network traffic

Back contact buffer layer for thin-film solar cells

Science.gov (United States)

Compaan, Alvin D.; Plotnikov, Victor V.

2014-09-09

A photovoltaic cell structure is disclosed that includes a buffer/passivation layer at a CdTe/Back contact interface. The buffer/passivation layer is formed from the same material that forms the n-type semiconductor active layer. In one embodiment, the buffer layer and the n-type semiconductor active layer are formed from cadmium sulfide (CdS). A method of forming a photovoltaic cell includes the step of forming the semiconductor active layers and the buffer/passivation layer within the same deposition chamber and using the same material source.

Solubilization of proteins: the importance of lysis buffer choice.

Science.gov (United States)

Peach, Mandy; Marsh, Noelle; Miskiewicz, Ewa I; MacPhee, Daniel J

2015-01-01

The efficient extraction of proteins of interest from cells and tissues is not always straightforward. Here we demonstrate the differences in extraction of the focal adhesion protein Kindlin-2 from choriocarcinoma cells using NP-40 and RIPA lysis buffer. Furthermore, we demonstrate the use of a more denaturing urea/thiourea lysis buffer for solubilization, by comparing its effectiveness for solubilization of small heat-shock proteins from smooth muscle with the often utilized RIPA lysis buffer. Overall, the results demonstrate the importance of establishing the optimal lysis buffer for specific protein solubilization within the experimental workflow.

Effect of Buffer Bow Structure in Ship-Ship Collision

DEFF Research Database (Denmark)

Yamada, Yasuhira; Endo, Hisayoshi; Pedersen, Preben Terndrup

2008-01-01

tankers, the introduction of buffer bulbous bows has been proposed. Relatively soft buffer bows absorb part of the kinetic energy of the striking ship before penetrating the inner hull of the struck vessel. The purpose of the present paper is to verify the effectiveness of a prototype buffer bulbous bow......) and the forward velocity of the struck ship on the collapse mode of the bow of the striking vessel are investigated. Collapse modes, contact forces and energy absorption capabilities of the buffer bows are compared with those of conventional bows....

A novel contra propagating ultrasonic flowmeter using glad buffer rods for high temperature measurement. Application to the oil and gas industries

Energy Technology Data Exchange (ETDEWEB)

Franca, Demartonne R. [Brasilia Univ., DF (Brazil). Dept. de Engenharia Eletrica; Cheng-Kuei Jen; Yuu Ono [National Research Council (NRC), Quebec (Canada). Industrial Materials Institute

2005-07-01

Ultrasonic techniques are attractive for process monitoring and control because they are non-intrusive, robust and inexpensive. Two common concerns limiting the high temperature performance of conventional ultrasonic systems for flow measurement are related to transducers and couplants. A suitable approach to overcoming this drawback is to insert a thermal isolating buffer rod with good ultrasonic performance (e.g., high signal-to-noise ratio). This requirement is important because, a priori, the noises generated in the buffer rod may bury the desired signals, so that no meaningful information is extracted. Besides protecting the ultrasonic transducers from overheating in applications such as high temperature flow measurements, buffer rods are also a solution for the couplant between the probe and tested sample, since their probing end can be directly wetted by fluids. Here, we propose clad buffer rods driven by shear transducers as the main building block of contra propagating ultrasonic flowmeters for high temperature application. It is demonstrated that the superior signal-to-noise ratio exhibit by clad buffer rods compared to the reported non-clad counterparts improve precision in transit-time measurement, leading to more accurate flow speed determination. In addition, it is shown that clad buffer rods generate specific ultrasonic signals for temperature calibration of flowmeters, allowing temperature variation while still measuring accurately the flow speed. These results are of interest for the oil and gas industries. (author)

The quantitation of buffering action II. Applications of the formal & general approach

Science.gov (United States)

Schmitt, Bernhard M

2005-01-01

Background The paradigm of "buffering" originated in acid-base physiology, but was subsequently extended to other fields and is now used for a wide and diverse set of phenomena. In the preceding article, we have presented a formal and general approach to the quantitation of buffering action. Here, we use that buffering concept for a systematic treatment of selected classical and other buffering phenomena. Results H+ buffering by weak acids and "self-buffering" in pure water represent "conservative buffered systems" whose analysis reveals buffering properties that contrast in important aspects from classical textbook descriptions. The buffering of organ perfusion in the face of variable perfusion pressure (also termed "autoregulation") can be treated in terms of "non-conservative buffered systems", the general form of the concept. For the analysis of cytoplasmic Ca++ concentration transients (also termed "muffling"), we develop a related unit that is able to faithfully reflect the time-dependent quantitative aspect of buffering during the pre-steady state period. Steady-state buffering is shown to represent the limiting case of time-dependent muffling, namely for infinitely long time intervals and infinitely small perturbations. Finally, our buffering concept provides a stringent definition of "buffering" on the level of systems and control theory, resulting in four absolute ratio scales for control performance that are suited to measure disturbance rejection and setpoint tracking, and both their static and dynamic aspects. Conclusion Our concept of buffering provides a powerful mathematical tool for the quantitation of buffering action in all its appearances. PMID:15771784

Retention of ionisable compounds on high-performance liquid chromatography. XV. Estimation of the pH variation of aqueous buffers with the change of the acetonitrile fraction of the mobile phase.

Science.gov (United States)

Subirats, Xavier; Bosch, Elisabeth; Rosés, Martí

2004-12-03

The most commonly used mobile phases in reversed-phase high-performance liquid chromatography (RP-HPLC) are hydro-organic mixtures of an aqueous buffer and an organic modifier. The addition of this organic solvent to buffered aqueous solutions involves a variation of the buffer properties (pH and buffer capacity). In this paper, the pH variation is studied for acetic acid-acetate, phosphoric acid-dihydrogenphosphate-hydrogenphosphate, citric acid-dihydrogencitrate-citrate, and ammonium-ammonia buffers. The proposed equations allow pH estimation of acetonitrile-water buffered mobile phases up to 60% (v/v) of organic modifier and initial aqueous buffer concentrations between 0.001 and 0.1 mol L(-1), from the initial aqueous pH. The estimated pH variation of the mobile phase and the pKa variation of the analytes allow us to predict the degree of ionisation of the analytes and from this and analyte hydrophobicities, to interpret the relative retention and separation of analyte mixtures.

Emotional labour and work engagement among nurses: examining perceived compassion, leadership and work ethic as stress buffers.

Science.gov (United States)

Mauno, Saija; Ruokolainen, Mervi; Kinnunen, Ulla; De Bloom, Jessica

2016-05-01

The study examined whether three resources, that is, compassion, transformational leadership and work ethic feasibility, buffer against the negative effects of emotional labour on work engagement. Emotional labour is a common job stressor among nurses, but little is known about whether certain personal and work resources buffer against it in relation to work engagement. Revealing buffers of emotional labour would help organizations to design tailored interventions. Cross-sectional online survey conducted in 2014. Participants were 3466 Finnish nurses. Hypotheses were tested via hierarchical moderated regression analyses. Higher emotional labour related to lower engagement. Two interaction effects were found. First, work ethic feasibility buffered against emotional labour: the nurses who perceived work ethic feasibility as high in a situation of high emotional labour, scored higher on engagement compared with those nurses who in this stress situation perceived work ethic feasibility to be low. Second, high compassion was detrimental to engagement in the presence of high emotional labour. Transformational leadership did not act as a buffer but showed a positive relationship with engagement. Work ethic feasibility (being able to work according to high ethical standards) is an important resource in nursing as it protects an employee against the negative effects of emotional labour and as it also directly promotes engagement. However, compassion may not always be beneficial in nursing, especially if co-occurring with high job stress. Transformational leadership has potential to improve engagement in nursing although it may not operate as a stress buffer. © 2016 John Wiley & Sons Ltd.

Molding method of buffer material for underground disposal of radiation-contaminated material, and molded buffer material

International Nuclear Information System (INIS)

Akasaka, Hidenari; Shimura, Satoshi; Kawakami, Susumu; Ninomiya, Nobuo; Yamagata, Junji; Asano, Eiichi

1995-01-01

Upon molding of a buffer material to be used upon burying a vessel containing radiation-contaminated materials in a sealed state, a powdery buffer material to be molded such as bentonite is disposed at the periphery of a mandrel having a cylindrical portion somewhat larger than contaminate container to be subjected to underground disposal. In addition, it is subjected to integration-molding such as cold isotropic press with a plastic film being disposed therearound, to form a molding product at high density. The molding product is released and taken out with the plastic film being disposed thereon. Releasability from an elastic mold is improved by the presence of the plastic film. In addition, if it is stored or transported while having the plastic film being disposed thereon, swelling of the buffer material due to water absorption or moisture absorption can be suppressed. (T.M.)

A liquid-crystal-on-silicon color sequential display using frame buffer pixel circuits

Science.gov (United States)

Lee, Sangrok

Next generation liquid-crystal-on-silicon (LCOS) high definition (HD) televisions and image projection displays will need to be low-cost and high quality to compete with existing systems based on digital micromirror devices (DMDs), plasma displays, and direct view liquid crystal displays. In this thesis, a novel frame buffer pixel architecture that buffers data for the next image frame while displaying the current frame, offers such a competitive solution is presented. The primary goal of the thesis is to demonstrate the LCOS microdisplay architecture for high quality image projection displays and at potentially low cost. The thesis covers four main research areas: new frame buffer pixel circuits to improve the LCOS performance, backplane architecture design and testing, liquid crystal modes for the LCOS microdisplay, and system integration and demonstration. The design requirements for the LCOS backplane with a 64 x 32 pixel array are addressed and measured electrical characteristics matches to computer simulation results. Various liquid crystal (LC) modes applicable for LCOS microdisplays and their physical properties are discussed. One- and two-dimensional director simulations are performed for the selected LC modes. Test liquid crystal cells with the selected LC modes are made and their electro-optic effects are characterized. The 64 x 32 LCOS microdisplays fabricated with the best LC mode are optically tested with interface circuitry. The characteristics of the LCOS microdisplays are summarized with the successful demonstration.

Radiation damage to human erythrocytes. Relative contribution of hydroxyl and chloride radicals in N2O-saturated buffers

International Nuclear Information System (INIS)

Krokosz, Anita; Komorowska, Magdalena A.; Szweda-Lewandowska, Zofia

2008-01-01

The erythrocyte suspensions in Na-phosphate buffered isotonic NaCl solution (PBS) or Na-phosphate isotonic buffer (PB) (hematocrit 1%) were irradiated with the dose of 400 Gy under N 2 O. Erythrocytes were incubated in the medium in which the cells were irradiated or in fresh PBS. The level of damage to cells was estimated on the basis of the course of post-radiation hemolysis and hemoglobin (Hb) oxidation. The medium in which the cells were irradiated and incubated influenced the course of the post-radiation hemolysis and Hb oxidation as well as some other parameters. We discussed the contribution of hydroxyl and chloride radicals in the initiation of erythrocyte damage and oxygen modification of these processes

Buffering capacity: its relevance in soil and water pollution

Energy Technology Data Exchange (ETDEWEB)

Stigliani, W.M. [University of Northern Iowa, Cedar Falls (United States)

1996-02-01

Buffering capacities in soils are essential for neutralizing or immobilizing inputs of acids and heavy metals. There are four major buffering regimes, each of which operates in a defined pH range. When the rate of pollutant inputs exceeds the rate of natural replenishment of the buffer in a specific regime, the supply of buffer will be exhausted over time, and the soil may switch to a regime at lower pH. As the pH of the soil declines, so does its capacity to immobilize heavy metals. If the soil initially has a moderately high buffering capacity, the time scale before exhaustion is on the order of decades to a century. Over this time there may be no observable environmental effects. When the effects do become obvious, it may be too late to reverse the damage. The importance of buffering capacity as a valued environmental resource must be recognized, and its preservation must be a major component of long-term soil protection policies. (Author). 17 refs., 6 figs., 1 tab.

Emplacement of small and large buffer blocks

International Nuclear Information System (INIS)

Saari, H.; Nikula, M.; Suikki, M.

2010-05-01

The report describes emplacement of a buffer structure encircling a spent fuel canister to be deposited in a vertical hole. The report deals with installability of various size blocks and with an emplacement gear, as well as evaluates the achieved quality of emplacement and the time needed for installing the buffer. Two block assembly of unequal size were chosen for examination. A first option involved small blocks, the use of which resulted in a buffer structure consisting of small sector blocks 200 mm in height. A second option involved large blocks, resulting in a buffer structure which consists of eight blocks. In these tests, the material chosen for both block options was concrete instead of bentonite. The emplacement test was a three-phase process. A first phase included stacking a two meter high buffer structure with small blocks for ensuring the operation of test equipment and blocks. A second phase included installing buffer structures with both block options to a height matching that of a canister-encircling cylindrical component. A third phase included testing also the installability of blocks to be placed above the canister by using small blocks. In emplacement tests, special attention was paid to the installability of blocks as well as to the time required for emplacement. Lifters for both blocks worked well. Due to the mass to be lifted, the lifter for large blocks had a more heavy-duty frame structure (and other lifting gear). The employed lifters were suspended in the tests on a single steel wire rope. Stacking was managed with both block sizes at adequate precision and stacked-up towers were steady. The stacking of large blocks was considerably faster. Therefore it is probably that the overall handling of the large blocks will be more convenient at a final disposal site. From the standpoint of reliability in lifting, the small blocks were safer to install above the canister. In large blocks, there are strict shape-related requirements which are

Development and application of a green-chemistry solution deposition technique for buffer layer coating on cube-textured metal substrates in view of further deposition of rare-earth based superconductors

DEFF Research Database (Denmark)

Pallewatta, Pallewatta G A P

which consist of YBCO superconducting coatings on cube-textured Ni based alloy tapes.  Before the epitaxial deposition this superconducting layer, a buffer layer is applied on the metal substrate as a diffusion barrier which is also required to transfer the strong texture of the underlying substrate......, allowing the epitaxial growth of the superconducting layer. State-of-the-art coated conductor hetero structures are mainly based on CeO2 based buffer stacks that consist of a sequence of several different buffer layers. Buffer layers deposited by continuous chemical deposition techniques, which...... is expected to be very advantageous in reel-to-reel applications. The thickness of these SrTiO3 monolayers was large enough to stop the nickel and copper diffusion from the Cu/Ni substrate. Hence, the developed high quality buffer layers are expected to be acting as efficient diffusion barriers and also...

Effects of buffer ionization in protein transition volumes.

Science.gov (United States)

Lee, Soyoung; Heerklotz, Heiko; Chalikian, Tigran V

2010-05-01

Protein denaturation events are generally associated with a change in the state of ionization of abnormally titrating groups and, therefore, are coupled with changes in buffer ionization/neutralization equilibria. Consequently, buffer ionization should influence the measured change in volume accompanying protein denaturation. Changes in volume accompanying protein denaturation reflect the differential packing and hydration of polypeptide chains in their native and denatured conformations while also describing the pressure stability of proteins. A characteristic feature of conformational transitions of globular proteins is a near zero change in volume that is comparable in magnitude with the volume of ionization of biologically relevant buffers. Thus, the impact of buffer ionization on the volume of protein denaturation could be very significant with the potential to affect not only its magnitude but also its sign. To investigate this point quantitatively, we performed pressure perturbation calorimetric (PPC) studies of lysozyme and ribonuclease A at pH 3.0 in four buffers differing in their ionization volumes. Our results identify buffer ionization as an important determinant of protein transition volume that needs to be carefully taken into account. We emphasize that the importance of our results is not limited to PPC measurements but is more general and applies to all volumetric investigations, in particular, extending to the derivation of the pressure-temperature phase diagram of protein stability.

Performance Enhancement of Small Molecular Solar Cells by Bilayer Cathode Buffer.

Science.gov (United States)

Sun, Qinjun; Zhao, Huanbin; Zhou, Miao; Gao, Liyan; Hao, Yuying

2016-04-01

An effective composite bilayer cathode buffer structure is proposed for use in small molecular solar cells. CsF was doped in Alq3 to form the first cathode buffer, leading to small serial resistances. BCP was used as the second cathode buffer to block the holes to the electrode. The optimized bilayer cathode buffer significantly increased the short circuit and fill factor of devices. By integrating this bilayer cathode buffer, the CuPc/C60 small molecular heterojunction cell exhibited a power conversion efficiency of up to 0.8%, which was an improvement of 56% compared to a device with only the Alq3 cathode buffer. Meanwhile, the bilayer cathode buffer still has a good protective effect on the performance of the device.

Current status of mechanical erosion studies of bentonite buffer

International Nuclear Information System (INIS)

Sane, P.; Olin, M.; Koskinen, K.

2013-08-01

The performance of the bentonite buffer in KBS-3-type nuclear waste repository concept relies to a great extent on the buffer surrounding the canister having sufficient dry density. Loss of buffer material caused by erosion remains as the most significant process reducing the density of the buffer. The mechanical erosion, or pre-saturation erosion, is the process where flowing groundwater transports buffer material away from the deposition hole towards the deposition tunnel. This process reduces the overall buffer density and potentially creates localized regions of low density. In the worst case the process is assumed to last as long as the free volume between the pellets in the pellets filled regions is filled with groundwater. With fixed environmental and material parameters a set of experiments was performed, testing the erosive properties of different buffer and backfill materials (MX-80 and Friedland Clay) in different groundwater conditions. The method used was a pinhole erosion test using two sizescales; 100 mm and 400 mm of cell length. The purpose of the pinhole tests was to test the scenario where piping channel is formed in the buffer and water flows through a single channel. The erosion data was produced with two methods, firstly the time-related erosion rates measured in-situ during the measurement and secondly the overall mass loss in the sample cell measured after dismantling of the test. It was observed that erosion in piping channels decreases rapidly (∼24 h) and irreversibly to a level that is an order of magnitude lower than the peak values. (orig.)

Effects of buffer thickness on ATW blanket performance

International Nuclear Information System (INIS)

Yang, W. S.; Mercatali, L.; Taiwo, T. A.; Hill, R. N.

2001-01-01

This paper presents preliminary results of target and buffer design studies for liquid metal cooled accelerator transmutation of waste (ATW) systems, aimed at maximizing the source importance while simultaneously reducing the irradiation damage to fuel. Using 840 MWt liquid metal cooled ATW designs, the effects of buffer thickness on the blanket performance have been studied. Varying the buffer thickness for a given blanket configuration, system performance parameters have been estimated by a series of calculations using the MCNPX and REBUS-3 codes. The effects of source importance variation are studied by investigating the low-energy ( and lt; 20 MeV) neutron source distribution and the equilibrium cycle blanket performance parameters such as fuel inventory, discharge burnup, burnup reactivity loss, and peak fast fluence. For investigating irradiation damage to fuel, the displacements per atom (dpa), hydrogen production, and helium production rates are evaluated at the buffer and blanket interface where the peak fast fluence occurs. Results for the liquid-metal-cooled designs show that the damage rates and the source importance increase monotonically as the buffer thickness decreases. Based on a compromise between the competing objectives of increasing the source importance and reducing the damage rates, a buffer thickness of around 20 cm appears to be reasonable. Investigation of the impact of the proton beam energy on the target and buffer design shows that for a given blanket power level, a lower beam energy (0.6 GeV versus 1 GeV) results in a higher irradiation damage to the beam window. This trend occurs because of the increase in the beam intensity required to maintain the power level

Effects of Buffer Thickness on ATW Blanket Performance

International Nuclear Information System (INIS)

Yang, W.S.; Mercatali, L.; Taiwo, T.A.; Hill, R.N.

2002-01-01

This paper presents preliminary results of target and buffer design studies for liquid metal cooled accelerator transmutation of waste (ATW) systems, aimed at maximizing the source importance while simultaneously reducing the irradiation damage to fuel. Using 840 MWt liquid metal cooled ATW designs, the effects of buffer thickness on the blanket performance have been studied. Varying the buffer thickness for a given blanket configuration, system performance parameters have been estimated by a series of calculations using the MCNPX and REBUS-3 codes. The effects of source importance variation are studied by investigating the low-energy (< 20 MeV) neutron source distribution and the equilibrium cycle blanket performance parameters such as fuel inventory, discharge burnup, burnup reactivity loss, and peak fast fluence. For investigating irradiation damage to fuel, the displacements per atom (dpa), hydrogen production, and helium production rates are evaluated at the buffer and blanket interface where the peak fast fluence occurs. Results for the liquid-metal-cooled designs show that the damage rates and the source importance increase monotonically as the buffer thickness decreases. Based on a compromise between the competing objectives of increasing the source importance and reducing the damage rates, a buffer thickness of around 20 cm appears to be reasonable. Investigation of the impact of the proton beam energy on the target and buffer design shows that for a given blanket power level, a lower beam energy (0.6 GeV versus 1 GeV) results in a higher irradiation damage to the beam window. This trend occurs because of the increase in the beam intensity required to maintain the power level. (authors)

Rapid synthesis of CdSe nanocrystals in aqueous solution at room ...

Indian Academy of Sciences (India)

Administrator

Water-soluble thioglycolic acid-capped CdSe nanocrystals (NCs) were prepared in aqueous solu- tion at room temperature. We investigated the ... NCs dispersed in buffer solution (pH = 4⋅0). FTIR spectra were recorded on a ... the theory of acid-base equilibrium, the initial pH value of original solution determines the ...

Determination of uranium in aqueous solutions by HPLC post column UV/VIS detection

International Nuclear Information System (INIS)

Abbasi, W.A.; Street, M.

1995-01-01

Analysis of uranium in different nitric acid concentration solutions is interest in nuclear industry where it is present in various process and waste streams. A method for the determination of uranium(VI) in nitric acid solution in described using ion chromatography and post-column derivatization with 4-(2-pyridylazo) resorcinol (PAR). The method does not require any sample treatment for acid removal or neutralization and can be used for routine laboratory analysis. The effluent used was ammonium sulphate / sulphuric acid and PAR was present in ammonium hydroxide/acetic acid buffer. The column effluents is reacted with PAR in a reaction coil and U(VI)-PAR complex is detector at 528 nm. The lowest uranium concentration detected was 100 ppb (0.1 mg/sup -1/) and linearity of up to 8 mgl -1 concentration was verified. The standard deviation in reproducibility at uranium concentration of 0.1 mgl/sup -1/ was 0.82%. (author)

Activity of the Human Rhinovirus 3C Protease Studied in Various Buffers, Additives and Detergents Solutions for Recombinant Protein Production

DEFF Research Database (Denmark)

Ullah, Raheem; Shah, Majid Ali; Tufail, Soban

2016-01-01

stringent sequence specificity and enhanced activity. Like other proteases, activity of the human rhinovirus 3C protease can be affected in part by the buffer components and additives that are generally employed for purification and stabilization of proteins, hence, necessitate their removal by tedious...

Accelerating Science with the NERSC Burst Buffer Early User Program

Energy Technology Data Exchange (ETDEWEB)

Bhimji, Wahid [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Bard, Debbie [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Romanus, Melissa [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Rutgers Univ., New Brunswick, NJ (United States); Paul, David [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Ovsyannikov, Andrey [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Friesen, Brian [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Bryson, Matt [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Correa, Joaquin [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Lockwood, Glenn K. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Tsulaia, Vakho [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Byna, Suren [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Farrell, Steve [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Gursoy, Doga [Argonne National Lab. (ANL), Argonne, IL (United States). Advanced Photon Source (APS); Daley, Chris [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Beckner, Vince [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Van Straalen, Brian [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Trebotich, David [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Tull, Craig [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Weber, Gunther H. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Wright, Nicholas J. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Antypas, Katie [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Prabhat, none [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2016-01-01

NVRAM-based Burst Buffers are an important part of the emerging HPC storage landscape. The National Energy Research Scientific Computing Center (NERSC) at Lawrence Berkeley National Laboratory recently installed one of the first Burst Buffer systems as part of its new Cori supercomputer, collaborating with Cray on the development of the DataWarp software. NERSC has a diverse user base comprised of over 6500 users in 700 different projects spanning a wide variety of scientific computing applications. The use-cases of the Burst Buffer at NERSC are therefore also considerable and diverse. We describe here performance measurements and lessons learned from the Burst Buffer Early User Program at NERSC, which selected a number of research projects to gain early access to the Burst Buffer and exercise its capability to enable new scientific advancements. To the best of our knowledge this is the first time a Burst Buffer has been stressed at scale by diverse, real user workloads and therefore these lessons will be of considerable benefit to shaping the developing use of Burst Buffers at HPC centers.

Experiments on thermal conductivity in buffer materials for geologic repository

International Nuclear Information System (INIS)

Kanno, T.; Yano, T.; Wakamatsu, H.; Matsushima, E.

1989-01-01

Engineered barriers for geologic disposal for HLW are planned to consist of canister, overpack and buffer elements. One of important physical characteristics of buffer materials is determining temperature profiles within the near field in a repository. Buffer materials require high thermal conductivity to disperse radiogenic heat away to the host rock. As the buffer materials, compacted blocks of the mixture of sodium bentonite and sand have been the most promising candidate in some countries, e.g. Sweden, Switzerland and Japan. The authors have been carrying out a series of thermal dispersion experiments to evaluate thermal conductivity of bentonite/quartz sand blocks. In this study, the following two factors considered to affect thermal properties of the near field were examined: effective thermal conductivities of buffer materials, and heat transfer characteristics of the gap between overpack and buffer materials

[Meeting point Stewart. Buffer bases, base excess and strong ions].

Science.gov (United States)

Lang, W

2007-04-01

Development of a two-buffer model which simulates the acid-base properties of blood and allows comparison of the different acidbase concepts according to Stewart and to Siggaard-Andersen. The two-buffer model consisted of different aqueous solutions of bicarbonate/CO(2) (pCO(2), sCO(2), pK(1)), HEPES buffer (A(tot), pK(a)) and electrolytes. These were used to calculate the pH from the independent variables according to Stewart - strong ion difference (SID), pCO(2) and total concentration of the weak acids (A(tot)) - from which all other dependent variables (cHCO(3)(-), cA(-), BB, BE) were obtained and compared with the measured values. The normal pH (7.408) was calculated from the normal values for SID (48 mmol/l), pCO(2) (40 mmHg) and A(tot) (45.2 mmol/l) and agreed perfectly with the measured value (7.409+/-0.001). This was also valid for all calculated and measured pH values when the SID was varied: non-respiratory alkalosis ( upward arrow) or acidosis ( downward arrow), pCO(2):respiratory acidosis ( upward arrow) or alkalosis ( downward arrow) and A(tot):hyperproteinemic acidosis ( upward arrow) or hypoproteinemic alkalosis ( downward arrow) were varied and the sum of the buffer bases (BB) was always equal to the SID. All changes and hence BE were also equal, providing that A(tot) was normal. This was not the case, however, if A(tot) was outside the normal range, when BE was then the difference from the normal BB at the respective reference point. Whereas the deviation of the measured pCO(2) was acceptable (1.74+/-0.86 mmHg), this was not the case for the SID (-6.18+/-3.58 mmol/l) calculated from the measured ion concentrations (Na, K, Ca, Cl). Despite controversial discussions, both concepts are much closer than might be expected. Whereas in the Stewart approach the focus of analysis is on plasma, with the Siggaard-Andersen approach it is on blood. Hence, a combined analysis of the blood gases (pH, pCO(2), pO(2), sO(2), cHb, BE) and of the strong ion gap (SIG

Persistent vs. Permanent Income Shocks in the Buffer-Stock Model

DEFF Research Database (Denmark)

Druedahl, Jeppe; Jørgensen, Thomas Høgholm

2017-01-01

relative risk aversion (CRRA) coefficient. If used for calibration, misspecified preferences could, for example, lead to a serious misjudgment in the value of social insurance mechanisms. Economic behavior, such as the marginal propensity to consume (MPC), of households simulated from the estimated......We investigate the effects of assuming a fully permanent income shock in a standard buffer-stock consumption model, when the true income process is only highly persistent. This assumption is computationally very advantageous, and thus often used, but might be problematic due to the implied...... (misspecified) model is, on the other hand, rather close to that from the correctly specified model....

Methyl Bromide Commodity Fumigation Buffer Zone Lookup Tables

Science.gov (United States)

Product labels for methyl bromide used in commodity and structural fumigation include requirements for buffer zones around treated areas. The information on this page will allow you to find the appropriate buffer zone for your planned application.