Effect of wind generation system types on Micro-Grid (MG) fault performance during both standalone and grid connected modes

International Nuclear Information System (INIS)

Kamel, Rashad M.

2014-01-01

Highlights: • This paper evaluated the effects of different wind system types on fault performance of Micro-Grid. • Both standalone and grid connected modes are considered. • The MG earthing system configuration is taken in consideration. - Abstract: Recently, there are three wind generation (WG) system types. The first type is called Fixed Speed Wind Generation (FSWG) system, which employs squirrel cage induction generators. Double Fed Induction Generator (DFIG) is utilized in the second type. The third type is called Full Converter Wind Generation (FCWG) system, which is interfaced with Micro-Grid (MG) through a back to back converter. During fault occurrence, each WG has its performance and characteristics which are determined by the generator physical characteristics and the MG earthing system configuration. For some WG types, the fault current depends also on the control algorithm of the power converter. The main target of this paper is to investigate and estimate how the fault performance of MG during both standalone and grid-connected modes is influenced by the type of WG. It is found during standalone mode that the type of the employed WG has a dominant impact on the MG performance under fault disturbance. On the contrary, the type of the employed WG has a negligible effect on the MG fault performance during grid-connected mode. This is because the main grid contributes most of the fault current. Effects of earthing system type on MG performance are highlighted

Stand-alone flat-plate photovoltaic power systems: System sizing and life-cycle costing methodology for Federal agencies

Science.gov (United States)

Borden, C. S.; Volkmer, K.; Cochrane, E. H.; Lawson, A. C.

1984-01-01

A simple methodology to estimate photovoltaic system size and life-cycle costs in stand-alone applications is presented. It is designed to assist engineers at Government agencies in determining the feasibility of using small stand-alone photovoltaic systems to supply ac or dc power to the load. Photovoltaic system design considerations are presented as well as the equations for sizing the flat-plate array and the battery storage to meet the required load. Cost effectiveness of a candidate photovoltaic system is based on comparison with the life-cycle cost of alternative systems. Examples of alternative systems addressed are batteries, diesel generators, the utility grid, and other renewable energy systems.

A Standalone Vision Impairments Simulator for Java Swing Applications

Science.gov (United States)

Oikonomou, Theofanis; Votis, Konstantinos; Korn, Peter; Tzovaras, Dimitrios; Likothanasis, Spriridon

A lot of work has been done lately in an attempt to assess accessibility. For the case of web rich-client applications several tools exist that simulate how a vision impaired or colour-blind person would perceive this content. In this work we propose a simulation tool for non-web JavaTM Swing applications. Developers and designers face a real challenge when creating software that has to cope with a lot of interaction situations, as well as specific directives for ensuring an accessible interaction. The proposed standalone tool will assist them to explore user-centered design and important accessibility issues for their JavaTM Swing implementations.

The challenge of pelvic discontinuity: cup-cage reconstruction does better than conventional cages in mid-term.

Science.gov (United States)

Abolghasemian, M; Tangsaraporn, S; Drexler, M; Barbuto, R; Backstein, D; Safir, O; Kuzyk, P; Gross, A

2014-02-01

The use of ilioischial cage reconstruction for pelvic discontinuity has been replaced by the Trabecular Metal (Zimmer, Warsaw, Indiana) cup-cage technique in our institution, due to the unsatisfactory outcome of using a cage alone in this situation. We report the outcome of 26 pelvic discontinuities in 24 patients (20 women and four men, mean age 65 years (44 to 84)) treated by the cup-cage technique at a mean follow-up of 82 months (12 to 113) and compared them with a series of 19 pelvic discontinuities in 19 patients (18 women and one man, mean age 70 years (42 to 86)) treated with a cage at a mean follow-up of 69 months (1 to 170). The clinical and radiological outcomes as well as the survivorship of the groups were compared. In all, four of the cup-cage group (15%) and 13 (68%) of the cage group failed due to septic or aseptic loosening. The seven-year survivorship was 87.2% (95% confidence interval (CI) 71 to 103) for the cup-cage group and 49.9% (95% CI 15 to 84) for the cage-alone group (p = 0.009). There were four major complications in the cup-cage group and nine in the cage group. Radiological union of the discontinuity was found in all successful cases in the cup-cage group and three of the successful cage cases. Three hips in the cup-cage group developed early radiological migration of the components, which stabilised with a successful outcome. Cup-cage reconstruction is a reliable technique for treating pelvic discontinuity in mid-term follow-up and is preferred to ilioischial cage reconstruction. If the continuity of the bone graft at the discontinuity site is not disrupted, early migration of the components does not necessarily result in failure.

Rescue Implantation of Expandable Cages for Severe Osteolysis and Cage Dislocation in the Lumbosacral Junction.

Science.gov (United States)

Schatlo, Bawarjan; Rohde, Veit; Solomiichuk, Volodymyr; von Eckardstein, Kajetan; Behm, Timo

2017-11-01

Osteolysis and implant loosening are commonly encountered problems after spinal instrumentation. In a patient who had previously undergone a posterior lumbar interbody fusion procedure, fusion did not occur, and a secondary cage dislocation led to an impingement of the L5 nerve root with severe radiculopathy. Revision surgery was performed. Intraoperatively, osteolysis was found to be so severe that conventional cages did not fill the void to allow for sufficient anterior column support. We used expandable transforaminal lumbar interbody fusion cages and implanted them bilaterally to replace the dislodged posterior lumbar interbody fusion cages. Clinical follow-up was uneventful. Imaging performed at 1 year showed satisfactory cage position and fusion. We propose the use of cages with the ability of ventral distraction in similar rescue interventions with cage dislocation and bone resorption. This may prevent a second surgery via a ventral approach. Copyright © 2017 Elsevier Inc. All rights reserved.

Porous organic cages

Science.gov (United States)

Tozawa, Tomokazu; Jones, James T. A.; Swamy, Shashikala I.; Jiang, Shan; Adams, Dave J.; Shakespeare, Stephen; Clowes, Rob; Bradshaw, Darren; Hasell, Tom; Chong, Samantha Y.; Tang, Chiu; Thompson, Stephen; Parker, Julia; Trewin, Abbie; Bacsa, John; Slawin, Alexandra M. Z.; Steiner, Alexander; Cooper, Andrew I.

2009-12-01

Porous materials are important in a wide range of applications including molecular separations and catalysis. We demonstrate that covalently bonded organic cages can assemble into crystalline microporous materials. The porosity is prefabricated and intrinsic to the molecular cage structure, as opposed to being formed by non-covalent self-assembly of non-porous sub-units. The three-dimensional connectivity between the cage windows is controlled by varying the chemical functionality such that either non-porous or permanently porous assemblies can be produced. Surface areas and gas uptakes for the latter exceed comparable molecular solids. One of the cages can be converted by recrystallization to produce either porous or non-porous polymorphs with apparent Brunauer-Emmett-Teller surface areas of 550 and 23m2g-1, respectively. These results suggest design principles for responsive porous organic solids and for the modular construction of extended materials from prefabricated molecular pores.

Cage-based performance capture

CERN Document Server

Savoye, Yann

2014-01-01

Nowadays, highly-detailed animations of live-actor performances are increasingly easier to acquire and 3D Video has reached considerable attentions in visual media production. In this book, we address the problem of extracting or acquiring and then reusing non-rigid parametrization for video-based animations. At first sight, a crucial challenge is to reproduce plausible boneless deformations while preserving global and local captured properties of dynamic surfaces with a limited number of controllable, flexible and reusable parameters. To solve this challenge, we directly rely on a skin-detached dimension reduction thanks to the well-known cage-based paradigm. First, we achieve Scalable Inverse Cage-based Modeling by transposing the inverse kinematics paradigm on surfaces. Thus, we introduce a cage inversion process with user-specified screen-space constraints. Secondly, we convert non-rigid animated surfaces into a sequence of optimal cage parameters via Cage-based Animation Conversion. Building upon this re...

Caging in high energy reactions

International Nuclear Information System (INIS)

Ache, H.J.

1977-01-01

The concept of caging high energy reactions is considered. It is noted that there is no easy and unambiguous way, short of a complete and very tedious product and mechanistic analysis, which is feasible only for very few systems, to determine the contribution made by caging. It is emphasized that some products resulting from the hot reaction with a certain substrate may be formed via caging while others are not. In research on the mechanism of caging the results of Roots work on the reactions of hot 18 F with the CF 3 CH 3 system seem to provide evidence for caging, with 18 F being the caged moiety, thus proceeding via a radical--radical recombination mechanism. Their work with H 2 S additive also seems to indicate that scavenging via hydrogen abstraction from H 2 S to form does not interfere with the radical--radical recombination consistent with Bunkers molecular approach to explain the cage effects. In other research a series of observations resulting from stereochemical and combined stereochemical density variation techniques seem to favor a caged-complex. It is clear that a more conclusive answer can only be reached by more systematic studies, utilizing the whole range of nuclear reactions such as (n,2n), (n,γ) and E.C. processes in mechanistically well defined systems to elucidate the effect of variations in the recoil energies, by carrying out studies in different solvents or host substances to assess the effect of the physical parameters, such as molecule size and intermolecular interactions on the escape probability or caging efficiencies

Do Lordotic Cages Provide Better Segmental Lordosis Versus Nonlordotic Cages in Lateral Lumbar Interbody Fusion (LLIF)?

Science.gov (United States)

Sembrano, Jonathan N; Horazdovsky, Ryan D; Sharma, Amit K; Yson, Sharon C; Santos, Edward R G; Polly, David W

2017-05-01

A retrospective comparative radiographic review. To evaluate the radiographic changes brought about by lordotic and nonlordotic cages on segmental and regional lumbar sagittal alignment and disk height in lateral lumbar interbody fusion (LLIF). The effects of cage design on operative level segmental lordosis in posterior interbody fusion procedures have been reported. However, there are no studies comparing the effect of sagittal implant geometry in LLIF. This is a comparative radiographic analysis of consecutive LLIF procedures performed with use of lordotic and nonlordotic interbody cages. Forty patients (61 levels) underwent LLIF. Average age was 57 years (range, 30-83 y). Ten-degree lordotic PEEK cages were used at 31 lumbar interbody levels, and nonlordotic cages were used at 30 levels. The following parameters were measured on preoperative and postoperative radiographs: segmental lordosis; anterior and posterior disk heights at operative level; segmental lordosis at supra-level and subjacent level; and overall lumbar (L1-S1) lordosis. Measurement changes for each cage group were compared using paired t test analysis. The use of lordotic cages in LLIF resulted in a significant increase in lordosis at operative levels (2.8 degrees; P=0.01), whereas nonlordotic cages did not (0.6 degrees; P=0.71) when compared with preoperative segmental lordosis. Anterior and posterior disk heights were significantly increased in both groups (Plordosis (lordotic P=0.86 vs. nonlordotic P=0.25). Lordotic cages provided significant increase in operative level segmental lordosis compared with nonlordotic cages although overall lumbar lordosis remained unchanged. Anterior and posterior disk heights were significantly increased by both cages, providing basis for indirect spinal decompression.

Outcomes of interbody fusion cages used in 1 and 2-levels anterior cervical discectomy and fusion: titanium cages versus polyetheretherketone (PEEK) cages.

Science.gov (United States)

Niu, Chi-Chien; Liao, Jen-Chung; Chen, Wen-Jer; Chen, Lih-Huei

2010-07-01

A prospective study was performed in case with cervical spondylosis who underwent anterior cervical discectomy and fusion (ACDF) with titanium or polyetheretherketone (PEEK) cages. To find out which fusion cage yielded better clinical and radiographic results. Although use of autogenous iliac-bone grafts in ACDF for cervical disc diseases remain standard surgical procedure, donor site morbidity and graft collapse or breakage are concerns. Cage technology was developed to prevent these complications. However, there is no comparison regarding the efficacy between titanium and PEEK cage. January 2005 to January 2006, 53 patients who had 1 and 2-levels ACDF with titanium or PEEK cages were evaluated. We measured the rate and amount of interspace collapse, segmental sagittal angulations, and the radiographic fusion success rate. Odom criteria were used to assess the clinical results. The fusion rate was higher in the PEEK group (100% vs. 86.5%, P=0.0335). There was no significant difference between both groups in loss of cervical lordosis (3.2 + or - 2.4 vs. 2.8 + or - 3.4, P=0.166). The mean anterior interspace collapse (1.6 + or - 1.0 mm) in the titanium group was significantly higher than the collapse of the PEEK group (0.5 + or - 0.6 mm) (PPEEK group (PPEEK group achieved an 80% rate of successful clinical outcomes, compared with 75% in the titanium group (P=0.6642). The PEEK cage is superior to the titanium cage in maintaining cervical interspace height and radiographic fusion after 1 and 2-levels anterior cervical decompression procedures.

39 CFR 122.2 - Stand-alone special services.

Science.gov (United States)

2010-07-01

... 39 Postal Service 1 2010-07-01 2010-07-01 false Stand-alone special services. 122.2 Section 122.2 Postal Service UNITED STATES POSTAL SERVICE POST OFFICE SERVICES [DOMESTIC MAIL] SERVICE STANDARDS FOR MARKET-DOMINANT SPECIAL SERVICES PRODUCTS § 122.2 Stand-alone special services. (a) The service standard...

The Evolution of the Cup-Cage Technique for Major Acetabular Defects: Full and Half Cup-Cage Reconstruction.

Science.gov (United States)

Sculco, Peter K; Ledford, Cameron K; Hanssen, Arlen D; Abdel, Matthew P; Lewallen, David G

2017-07-05

Complex acetabular reconstruction for major bone loss can require advanced methods such as the use of a cup-cage construct. The purpose of this study was to review outcomes after the initial development of the cup-cage technique and the subsequent evolution to the use of a half cup-cage construct. We performed a retrospective, single-center review of 57 patients treated with cup-cage reconstruction for major acetabular bone loss. All patients had major acetabular defects graded as Paprosky Type 2B through 3B, with 34 (60%) having an associated pelvic discontinuity. Thirty patients received a full cup-cage construct and 27, a half cup-cage construct. The mean follow-up was 5 years. Both the full and half cup-cage cohorts demonstrated significantly improved Harris hip score (HHS) values, from 36 to 72 at a minimum of 2 years of follow-up (p cup-cage constructs and 6 (22%) of the half cup-cage constructs. One patient with a full cup-cage construct underwent re-revision of the acetabular component for progressive migration and aseptic loosening. Short-term survivorship free from re-revision for any cause or reoperation was 89% (83% and 96% for full and half cup-cage cohorts, respectively). Both full and half cup-cage constructs demonstrated successful clinical outcomes and survivorship in the treatment of major acetabular defects and pelvic discontinuity. Each method is utilized on the basis of individual intraoperative findings, including the extent and pattern of bone loss, the quality and location of host bone remaining after preparation, and the presence of pelvic discontinuity. Longer-term follow-up is required to understand the durability of these constructs in treating major acetabular defects and pelvic discontinuity. Therapeutic Level III. See Instructions for Authors for a complete description of levels of evidence.

Structure Optimization of Stand-Alone Renewable Power Systems Based on Multi Object Function

Directory of Open Access Journals (Sweden)

Jae-Hoon Cho

2016-08-01

Full Text Available This paper presents a methodology for the size optimization of a stand-alone hybrid PV/wind/diesel/battery system while considering the following factors: total annual cost (TAC, loss of power supply probability (LPSP, and the fuel cost of the diesel generator required by the user. A new optimization algorithm and an object function (including a penalty method are also proposed; these assist with designing the best structure for a hybrid system satisfying the constraints. In hybrid energy system sources such as photovoltaic (PV, wind, diesel, and energy storage devices are connected as an electrical load supply. Because the power produced by PV and wind turbine sources is dependent on the variation of the resources (sun and wind and the load demand fluctuates, such a hybrid system must be able to satisfy the load requirements at any time and store the excess energy for use in deficit conditions. Therefore, reliability and cost are the two main criteria when designing a stand-alone hybrid system. Moreover, the operation of a diesel generator is important to achieve greater reliability. In this paper, TAC, LPSP, and the fuel cost of the diesel generator are considered as the objective variables and a hybrid teaching–learning-based optimization algorithm is proposed and used to choose the best structure of a stand-alone hybrid PV/wind/diesel/battery system. Simulation results from MATLAB support the effectiveness of the proposed method and confirm that it is more efficient than conventional methods.

Development of furnished cages for laying hens.

Science.gov (United States)

Appleby, M C; Walker, A W; Nicol, C J; Lindberg, A C; Freire, R; Hughes, B O; Elson, H A

2002-09-01

1. A 3-year trial was carried out of cages for laying hens, occupying a full laying house. The main cage designs used were 5000 cm2 in area, 50 cm high at the rear and furnished with nests and perches. F cages had a front rollaway nest at the side, lined with artificial turf. FD cages also had a dust bath containing sand over the nest. H cages had two nest hollows at the side, one in front of the other. They were compared with conventional cages 2500 cm2 in area and 38 cm high at the rear. 2. Cages were stocked with from 4 to 8 ISA Brown hens per cage, resulting in varied allowances of area, feeder and perch per bird. No birds were beak trimmed. In F and FD cages two further treatments were applied: nests and dust baths were sometimes fitted with gates to exclude birds from dust baths in the morning and from both at night; elevated food troughs, with a lip 33 cm above the cage floor, were compared with standard troughs. 3. Management of the house was generally highly successful, with temperature control achieved by ventilation. Egg production was above breeders' standards and not significantly affected by cage design. More eggs per bird were collected when there were fewer birds per cage but food consumption also then tended to be higher. 4. The number of downgraded eggs was variable, with some tendency for more in furnished cages. Eggs laid in dust baths were often downgraded. Those laid at the back of the cage were frequently dirty because of accumulation of droppings. H nests were unsuccessful, with less than 50% of eggs laid in the nest hollows. However, up to 93% of eggs were laid in front rollaways, and few of these were downgraded. 5. Feather and foot damage were generally less in furnished than in conventional cages, greater where there were more birds per cage. With an elevated food trough there was less feather damage but more overgrowth of claws. In year 2, mortality was greater in cages with more birds. 6. Pre-laying behaviour was mostly settled in

[Experiences with cage combinations for guinea pigs].

Science.gov (United States)

von Zychlinski, J

1989-01-01

Special cage units described in 1982 for guinea pigs have been used either as cages for small groups of breeding animals or for caging of growing animals. By using these cages the following advantages have been noted; the cage size can be adapted to number, age and body weight of the animals; aggression and panic are avoided by corners, walls and tunnels; economic use of breeding males by mating with more females.

Stand-alone photovoltaic applications. Lessons learned

International Nuclear Information System (INIS)

Loois, G.; Van Hemert, B.

1999-02-01

The IEA Photovoltaic Power Systems Programme (PVPS) is one of the collaborative R and D agreements established within the IEA. The objective of Task III is to promote and facilitate the exchange of information and experiences in the field of PV Systems in Stand-alone and Island Applications (SAPV). The book focuses on the practical experiences gained, and does not aim to provide a complete manual on SAPV. When Task III started its activities in 1993, a collection of 50 'State of the art' projects was published in the book 'Examples of Stand-Alone Photovoltaic Systems'. This publication marked the base line for the work of the task. Now, in 1998, the showcases from each country demonstrate the lessons learned in five years of cooperation. The book consists of two parts. The first part contains eight chapters dealing with a specific aspect of stand-alone PV. The second part introduces 14 national showcase projects in a systematic presentation. Each chapter and showcase can be read independently from the rest of the book. Chapter 2, contributed by The Netherlands, analyses the market for stand-alone PV systems. It gives an overview of the 'traditional' application of stand-alone PV, which is the electrification of remote buildings and which has been addressed in depth in other publications. The focus is on the market niches of service applications that are also interesting for more densely populated areas, e.g. in industrialised countries. The United Kingdom illustrates the economic aspects in Chapter 3. Cost comparisons are made, but more important is the illustration of the non-financial considerations that make PV the preferred choice as a power source for many applications. Switzerland explores in Chapter 4 (financing aspects) different financing mechanisms, and financial policies used to overcome the initial cost barrier. Most of these approaches have been applied in developing countries rather than in the western world. Using various examples from all over the

Foldit Standalone: a video game-derived protein structure manipulation interface using Rosetta.

Science.gov (United States)

Kleffner, Robert; Flatten, Jeff; Leaver-Fay, Andrew; Baker, David; Siegel, Justin B; Khatib, Firas; Cooper, Seth

2017-09-01

Foldit Standalone is an interactive graphical interface to the Rosetta molecular modeling package. In contrast to most command-line or batch interactions with Rosetta, Foldit Standalone is designed to allow easy, real-time, direct manipulation of protein structures, while also giving access to the extensive power of Rosetta computations. Derived from the user interface of the scientific discovery game Foldit (itself based on Rosetta), Foldit Standalone has added more advanced features and removed the competitive game elements. Foldit Standalone was built from the ground up with a custom rendering and event engine, configurable visualizations and interactions driven by Rosetta. Foldit Standalone contains, among other features: electron density and contact map visualizations, multiple sequence alignment tools for template-based modeling, rigid body transformation controls, RosettaScripts support and an embedded Lua interpreter. Foldit Standalone is available for download at https://fold.it/standalone , under the Rosetta license, which is free for academic and non-profit users. It is implemented in cross-platform C ++ and binary executables are available for Windows, macOS and Linux. scooper@ccs.neu.edu. © The Author(s) 2017. Published by Oxford University Press.

TiN thin film deposition by cathodic cage discharge: effect of cage configuration and active species

International Nuclear Information System (INIS)

De Freitas Daudt, N; Cavalcante Braz, D; Alves Junior, C; Pereira Barbosa, J C; Barbalho Pereira, M

2012-01-01

Plasma cathodic cage technique was developed recently in order to eliminate phenomena such as edge effects and overheating, which occur during conventional nitriding processes. In this work, the effect of plasma active species and cage configurations during thin film deposition of TiN were studied. This compound was chosen because its properties are very sensitive to slight variations in chemical composition and film thickness, becoming a good monitoring tool in fabrication process control. In order to verify the effect of cage geometry on the discharge and characteristics of the grown film, a cage made of titanium was used with different numbers and distribution of holes. Furthermore, different amounts of hydrogen were added to the Ar + N2 plasma atmosphere. Flow rates of Ar and N2 gas were fixed at 4 and 3 sccm, respectively and flow rates of H 2 gas was 0, 1 and 2 sccm. Plasma species, electrical discharge and physical characteristics of the grown film were analyzed by Optical Emission Spectroscopy (OES), Atomic Force Microscopy (AFM), X-Ray Diffraction. It was observed by OES that the luminous intensity associated to Hα species is not proportional to flow rate of H 2 gas. Electrical efficiency of the system, crystal structure and topography of the TiN film are strongly influenced by this behavior. For constant flow rate of H 2 gas, it was found that with more holes at the top of the cage, deposition rate, crystallinity and roughness are higher, if compared to cages with a small number of holes at the top of cage. On the other hand, the opposite behavior was observed when more holes were located at the sidewall of cage.

Comparison Between Acrylic Cage and Polyetheretherketone (PEEK) Cage in Single-level Anterior Cervical Discectomy and Fusion: A Randomized Clinical Trial.

Science.gov (United States)

Farrokhi, Majid R; Nikoo, Zahra; Gholami, Mehrnaz; Hosseini, Khadijeh

2017-02-01

Prospective, single-blind randomized-controlled clinical study. To compare polyetheretherketone (PEEK) cage with a novel Acrylic cage to find out which fusion cage yielded better clinical outcomes following single-level anterior cervical discectomy and fusion (ACDF). ACDF is considered a standard neurosurgical treatment for degenerative diseases of cervical intervertebral disks. There are many options, including bone grafts, bone cement, and spacers made of titanium, carbon fiber, and synthetic materials, used to restore physiological disk height and enhance spinal fusion, but the ideal device, which would provide immediate structural support and subsequent osteointegration and stability, has not been identified yet. To overcome this, we designed a new, inexpensive Acrylic cage. A total of 64 patients were eligible to participate and were randomly allocated to undergo ACDF either with Acrylic interbody fusion cage filled with bone substitute (n=32) or PEEK cage (n=32). Nurick's grading was used for quantifying the neurological deficit. Clinical and radiologic outcome was assessed preoperatively, immediately after surgery, and subsequently at 2, 6, and 12 months of follow-up using Odom's criteria and dynamic radiographs (flexion-extension) and computed tomography scans, respectively. There was a statistically significant improvement in the clinical outcomes of the Acrylic cage group compared with the PEEK cage group (mean difference: -0.438; 95% confidence interval, -0.807 to -0.068; P=0.016). There was a statistically significant difference in disk space height increase between the 2 groups at the 6- and 12-month follow-up. The Acrylic cage achieved higher fusion rate (good fusion) than the PEEK cage (96.9% vs. 93.8%). Intervertebral angle demonstrated a significant difference among the 2 treated groups throughout the follow-up period. This study suggests that the use of Acrylic cage is associated with good clinical and radiologic outcomes and it can be therefore a

A novel test cage with an air ventilation system as an alternative to conventional cages for the efficacy testing of mosquito repellents.

Science.gov (United States)

Obermayr, U; Rose, A; Geier, M

2010-11-01

We have developed a novel test cage and improved method for the evaluation of mosquito repellents. The method is compatible with the United States Environmental Protection Agency, 2000 draft OPPTS 810.3700 Product Performance Test Guidelines for Testing of Insect Repellents. The Biogents cages (BG-cages) require fewer test mosquitoes than conventional cages and are more comfortable for the human volunteers. The novel cage allows a section of treated forearm from a volunteer to be exposed to mosquito probing through a window. This design minimizes residual contamination of cage surfaces with repellent. In addition, an air ventilation system supplies conditioned air to the cages after each single test, to flush out and prevent any accumulation of test substances. During biting activity tests, the untreated skin surface does not receive bites because of a screen placed 150 mm above the skin. Compared with the OPPTS 810.3700 method, the BG-cage is smaller (27 liters, compared with 56 liters) and contains 30 rather than hundreds of blood-hungry female mosquitoes. We compared the performance of a proprietary repellent formulation containing 20% KBR3023 with four volunteers on Aedes aegypti (L.) (Diptera: Culicidae) in BG- and conventional cages. Repellent protection time was shorter in tests conducted with conventional cages. The average 95% protection time was 4.5 +/- 0.4 h in conventional cages and 7.5 +/- 0.6 h in the novel BG-cages. The protection times measured in BG-cages were more similar to the protection times determined with these repellents in field tests.

Nanocaged platforms: modification, drug delivery and nanotoxicity. Opening synthetic cages to release the tiger.

Science.gov (United States)

Karimi, Mahdi; Zangabad, Parham Sahandi; Mehdizadeh, Fatemeh; Malekzad, Hedieh; Ghasemi, Alireza; Bahrami, Sajad; Zare, Hossein; Moghoofei, Mohsen; Hekmatmanesh, Amin; Hamblin, Michael R

2017-01-26

Nanocages (NCs) have emerged as a new class of drug-carriers, with a wide range of possibilities in multi-modality medical treatments and theranostics. Nanocages can overcome such limitations as high toxicity caused by anti-cancer chemotherapy or by the nanocarrier itself, due to their unique characteristics. These properties consist of: (1) a high loading-capacity (spacious interior); (2) a porous structure (analogous to openings between the bars of the cage); (3) enabling smart release (a key to unlock the cage); and (4) a low likelihood of unfavorable immune responses (the outside of the cage is safe). In this review, we cover different classes of NC structures such as virus-like particles (VLPs), protein NCs, DNA NCs, supramolecular nanosystems, hybrid metal-organic NCs, gold NCs, carbon-based NCs and silica NCs. Moreover, NC-assisted drug delivery including modification methods, drug immobilization, active targeting, and stimulus-responsive release mechanisms are discussed, highlighting the advantages, disadvantages and challenges. Finally, translation of NCs into clinical applications, and an up-to-date assessment of the nanotoxicology considerations of NCs are presented.

R and D into stand-alone PV systems for export

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-09-01

The current status of photovoltaic (PV) technology is reviewed for systems to provide electricity where mains supplies are unavailable, known as stand-alone PV systems. Typical applications and experiences with installed stand-alone systems are described. Economic issues and barriers to the wide use of PV systems are also examined. (UK)

Faraday Cage Protects Against Lightning

Science.gov (United States)

Jafferis, W.; Hasbrouck, R. T.; Johnson, J. P.

1992-01-01

Faraday cage protects electronic and electronically actuated equipment from lightning. Follows standard lightning-protection principles. Whether lightning strikes cage or cables running to equipment, current canceled or minimized in equipment and discharged into ground. Applicable to protection of scientific instruments, computers, radio transmitters and receivers, and power-switching equipment.

Automated home cage observations as a tool to measure the effects of wheel running on cage floor locomotion.

Science.gov (United States)

de Visser, Leonie; van den Bos, Ruud; Spruijt, Berry M

2005-05-28

This paper introduces automated observations in a modular home cage system as a tool to measure the effects of wheel running on the time distribution and daily organization of cage floor locomotor activity in female C57BL/6 mice. Mice (n = 16) were placed in the home cage system for 6 consecutive days. Fifty percent of the subjects had free access to a running wheel that was integrated in the home cage. Overall activity levels in terms of duration of movement were increased by wheel running, while time spent inside a sheltering box was decreased. Wheel running affected the hourly pattern of movement during the animals' active period of the day. Mice without a running wheel, in contrast to mice with a running wheel, showed a clear differentiation between novelty-induced and baseline levels of locomotion as reflected by a decrease after the first day of introduction to the home cage. The results are discussed in the light of the use of running wheels as a tool to measure general activity and as an object for environmental enrichment. Furthermore, the possibilities of using automated home cage observations for e.g. behavioural phenotyping are discussed.

Synchronisation of two separate zones in a standalone microgrid

Directory of Open Access Journals (Sweden)

Ying-Yi Hong

2017-06-01

Full Text Available Standalone microgrids that comprise distributed generation sources (DGSs or energy storage systems (ESSs exist on off-shore islands or remote areas. When a fault occurs in a standalone microgrid, the microgrid is separated into several zones with pre-specified DGS or ESS supplying power to local loads. After the fault is cleared, the three-phase voltages and frequencies may differ among these zones. To restore the original microgrid topology, these zones must be reconnected to each other by synchronisation. A synchronisation controller of the DGS/ESS that accounts for slightly different three-phase voltages and frequencies in two separate zones is presented. The Clark transform and Mamdani fuzzy rules are used to implement the controller, providing fast and seamless synchronisation. Simulation results using a standalone microgrid show the practical applicability of the proposed method.

A review on sizing methodologies of photovoltaic array and storage battery in a standalone photovoltaic system

International Nuclear Information System (INIS)

Khatib, Tamer; Ibrahim, Ibrahim A.; Mohamed, Azah

2016-01-01

Highlights: • We review the current methods for sizing standalone PV systems. • We review the current criteria adapted in sizing standalone PV systems. • We review current method for sizing battery in standalone PV systems. - Abstract: The reliance of future energy demand on standalone PV system is based on its payback period and particular electrical grid parity prices. This highlights the importance for optimum and applicable methods for sizing these systems. Moreover, the designers are being more sensitive toward simple and reliable sizing models for standalone PV system. This paper proposes a review on important knowledge that needs to be taken into account while designing and implementing standalone PV systems. Such a knowledge includes configurations of standalone photovoltaic system, evaluation criteria for unit sizing, sizing methodologies. Moreover, this review provides highlights on challenges and limitations of standalone PV system size optimization techniques.

Building a better Faraday cage

Science.gov (United States)

MartinAlfven; Wright, David; skocpol; Rounce, Graham; Richfield, Jon; W, Nick; wheelsonfire

2015-11-01

In reply to the physicsworld.com news article “Are Faraday cages less effective than previously thought?” (15 September, http://ow.ly/SfklO), about a study that indicated, based on mathematical modelling, that conducting wire-mesh cages may not be as good at excluding electromagnetic radiation as is commonly assumed.

Non-Gaussian nature of glassy dynamics by cage to cage motion

International Nuclear Information System (INIS)

Vorselaars, Bart; Lyulin, Alexey V.; Michels, M. A. J.; Karatasos, K.

2007-01-01

A model based on a single Brownian particle moving in a periodic effective field is used to understand the non-Gaussian dynamics in glassy systems of cage escape and subsequent recaging, often thought to be caused by a heterogeneous glass structure. The results are compared to molecular-dynamics simulations of systems with varying complexity: quasi-two-dimensional colloidlike particles, atactic polystyrene, and a dendritic glass. The model nicely describes generic features of all three topologically different systems, in particular around the maximum of the non-Gaussian parameter. This maximum is a measure for the average distance between cages

Effects of symmetrical voltage sags on squirrel-cage induction motors

Energy Technology Data Exchange (ETDEWEB)

Pedra, Joaquin; Sainz, Luis; Corcoles, Felipe [Department of Electrical Engineering, ETSEIB-UPC, Av. Diagonal, 647, 08028 Barcelona (Spain)

2007-10-15

This paper analyzes the symmetrical voltage sag consequences on the induction motor behavior when single- and double-cage models are considered, namely current and torque peaks, and speed loss. These effects depend on several variables like sag type, duration and depth. Voltage sag effects are studied by using single- and double-cage models for three motors of different rated power. The double-cage model always predicts torque and current peaks higher than those of the single-cage model. The single-cage model predicts that voltage sags can produce motor instability, whereas the double-cage model is always stable. Therefore, the double-cage model must be used for the simulation of the squirrel-cage induction motor, because the single-cage model can give erroneous results in some situations. (author)

A library of protein cage architectures as nanomaterials.

Science.gov (United States)

Flenniken, M L; Uchida, M; Liepold, L O; Kang, S; Young, M J; Douglas, T

2009-01-01

Virus capsids and other structurally related cage-like proteins such as ferritins, dps, and heat shock proteins have three distinct surfaces (inside, outside, interface) that can be exploited to generate nanomaterials with multiple functionality by design. Protein cages are biological in origin and each cage exhibits extremely homogeneous size distribution. This homogeneity can be used to attain a high degree of homogeneity of the templated material and its associated property. A series of protein cages exhibiting diversity in size, functionality, and chemical and thermal stabilities can be utilized for materials synthesis under a variety of conditions. Since synthetic approaches to materials science often use harsh temperature and pH, it is an advantage to utilize protein cages from extreme environments. In this chapter, we review recent studies on discovering novel protein cages from harsh natural environments such as the acidic thermal hot springs at Yellowstone National Park (YNP) and on utilizing protein cages as nano-scale platforms for developing nanomaterials with wide range of applications from electronics to biomedicine.

Photoactivatable Caged Prodrugs of VEGFR-2 Kinase Inhibitors

OpenAIRE

Boris Pinchuk; Rebecca Horbert; Alexander Döbber; Lydia Kuhl; Christian Peifer

2016-01-01

In this study, we report on the design, synthesis, photokinetic properties and in vitro evaluation of photoactivatable caged prodrugs for the receptor tyrosine kinase VEGFR-2. Highly potent VEGFR-2 inhibitors 1 and 3 were caged by introduction of a photoremovable protecting group (PPG) to yield the caged prodrugs 4 and 5. As expected, enzymatic and cellular proliferation assays showed dramatically diminished efficacy of caged prodrugs in vitro. Upon ultraviolet (UV) irradiation of the prodrug...

Design of a reliable and low-cost stand-alone micro hydropower station

Energy Technology Data Exchange (ETDEWEB)

Kusakana, K.; Munda, J.L. [Tshwane Univ. of Technology, Pretoria (South Africa)

2008-07-01

A stand-alone micro-hydropower station was presented. The plant was comprised of a squirrel cage induction machine coupled to a Kaplan water turbine. Power converters were used to control the variable frequency and voltage outputs of the generator caused by variations in water flow. The hydropower plant was installed a farm in the Kwazulu-Natal region of South Africa, and was designed to provide electricity in relation to the low power demand of users in the region as well as according to the site's hydrology and topology. Load forecasts for the 8 houses using the system were conducted. A generator with a higher output than the average power needed to feed the load was selected in order to ensure load supply during peak demand. The system was designed to shore energy generated during off-peak periods in batteries. An AC-DC-AC converter was used as an interface between the generator and the load in order to ensure voltage and frequency stabilization. Simulations of plant components were conducted to demonstrate output power supply during water flow variations. Results of the modelling study indicated that power converters are needed to stabilize generator outputs. The hydropower design is a cost-effective means of supplying power to low-income households. 10 refs., 2 tabs., 7 figs.

Homogenized boundary conditions and resonance effects in Faraday cages

OpenAIRE

Hewett, DP; Hewitt, IJ

2016-01-01

We present a mathematical study of two-dimensional electrostatic and electromagnetic shielding by a cage of conducting wires (the so-called `Faraday cage e ect'). Taking the limit as the number of wires in the cage tends to in nity we use the asymptotic method of multiple scales to derive continuum models for the shielding, involving homogenized boundary conditions on an e ective cage boundary. We show how the resulting models depend on key cage parameters such as the...

Computed tomography measurement of rib cage morphometry in emphysema.

Directory of Open Access Journals (Sweden)

Nicola Sverzellati

Full Text Available BACKGROUND: Factors determining the shape of the human rib cage are not completely understood. We aimed to quantify the contribution of anthropometric and COPD-related changes to rib cage variability in adult cigarette smokers. METHODS: Rib cage diameters and areas (calculated from the inner surface of the rib cage in 816 smokers with or without COPD, were evaluated at three anatomical levels using computed tomography (CT. CTs were analyzed with software, which allows quantification of total emphysema (emphysema%. The relationship between rib cage measurements and anthropometric factors, lung function indices, and %emphysema were tested using linear regression models. RESULTS: A model that included gender, age, BMI, emphysema%, forced expiratory volume in one second (FEV1%, and forced vital capacity (FVC% fit best with the rib cage measurements (R(2 = 64% for the rib cage area variation at the lower anatomical level. Gender had the biggest impact on rib cage diameter and area (105.3 cm(2; 95% CI: 111.7 to 98.8 for male lower area. Emphysema% was responsible for an increase in size of upper and middle CT areas (up to 5.4 cm(2; 95% CI: 3.0 to 7.8 for an emphysema increase of 5%. Lower rib cage areas decreased as FVC% decreased (5.1 cm(2; 95% CI: 2.5 to 7.6 for 10 percentage points of FVC variation. CONCLUSIONS: This study demonstrates that simple CT measurements can predict rib cage morphometric variability and also highlight relationships between rib cage morphometry and emphysema.

Cage effect in recoil studies

International Nuclear Information System (INIS)

Berei, K.

1983-09-01

The role of cage effect is one of the most discussed questions of hot atom chemistry in condensed organic systems. So far no direct evidence is available for assessing the exact contribution of thermal recombinations occurring in the liquid cage to the stabilization processes of recoil atoms. However, some conclusions can be drawn from experimental observations concerning the influence on product yield of hot atom recoil spectra, the effects of density, phase and long range order of the medium as well as from comparisons with systems providing cage walls of different chemical reactivities towards the recoil atom. Recent developments in this field are reviewed based primarily on the investigations of recoil halogen reactions in aliphatic and aromatic hydrocarbons and their haloderivatives. (author)

Validation of the standalone implementation of the dynamic wake meandering model for power production

DEFF Research Database (Denmark)

Keck, Rolf-Erik Henrik Jussi

2015-01-01

This paper presents validation for using the standalone implementation of the dynamic wake meandering (DWM) model to conduct numerical simulations of power production of rows of wind turbines. The standalone DWM model is an alternative formulation of the conventional DWM model that does not require...... information exchange with an aeroelastic code. As a consequence, the standalone DWM model has significantly shorter computational times and lower demands on the user environment. The drawback of the standalone DWM model is that it does not have the capability to predict turbine loads. Instead, it should...

Design and modeling of Faraday cages for substrate noise isolation

Science.gov (United States)

Wu, Joyce H.; del Alamo, Jesús A.

2013-07-01

A Faraday cage structure using through-substrate vias is an effective strategy to suppress substrate crosstalk, particularly at high frequencies. Faraday cages can reduce substrate noise by 32 dB at 10 GHz, and 26 dB at 50 GHz. We have developed lumped-element, equivalent circuit models of the Faraday cages and test structures to better understand the performance of the Faraday cages. These models compare well to measured results and show that the vias of the Faraday cage act as an RLC shunt to ground that draws substrate current. Designing a Faraday cage to achieve optimum isolation requires low via impedance and mitigation of via sidewall capacitance. The Faraday cage inductance is correlated to the number of vias and via spacing of the cage and can be optimized for the frequency of operation.

COATING ALTERNATIVES GUIDE (CAGE) USER'S GUIDE

Science.gov (United States)

The guide provides instructions for using the Coating Alternatives GuidE (CAGE) software program, version 1.0. It assumes that the user is familiar with the fundamentals of operating an IBM-compatible personal computer (PC) under the Microsoft disk operating system (MS-DOS). CAGE...

Comparison of changes in tidal volume associated with expiratory rib cage compression and expiratory abdominal compression in patients on prolonged mechanical ventilation.

Science.gov (United States)

Morino, Akira; Shida, Masahiro; Tanaka, Masashi; Sato, Kimihiro; Seko, Toshiaki; Ito, Shunsuke; Ogawa, Shunichi; Takahashi, Naoaki

2015-07-01

[Purpose] This study was designed to compare and clarify the relationship between expiratory rib cage compression and expiratory abdominal compression in patients on prolonged mechanical ventilation, with a focus on tidal volume. [Subjects and Methods] The subjects were 18 patients on prolonged mechanical ventilation, who had undergone tracheostomy. Each patient received expiratory rib cage compression and expiratory abdominal compression; the order of implementation was randomized. Subjects were positioned in a 30° lateral recumbent position, and a 2-kgf compression was applied. For expiratory rib cage compression, the rib cage was compressed unilaterally; for expiratory abdominal compression, the area directly above the navel was compressed. Tidal volume values were the actual measured values divided by body weight. [Results] Tidal volume values were as follows: at rest, 7.2 ± 1.7 mL/kg; during expiratory rib cage compression, 8.3 ± 2.1 mL/kg; during expiratory abdominal compression, 9.1 ± 2.2 mL/kg. There was a significant difference between the tidal volume during expiratory abdominal compression and that at rest. The tidal volume in expiratory rib cage compression was strongly correlated with that in expiratory abdominal compression. [Conclusion] These results indicate that expiratory abdominal compression may be an effective alternative to the manual breathing assist procedure.

The effect of pesticide residue on caged mosquito bioassays.

Science.gov (United States)

Barber, J A S; Greer, Mike; Coughlin, Jamie

2006-09-01

Wind tunnel experiments showed that secondary pickup of insecticide residue by mosquitoes in cage bioassays had a significant effect on mortality. Cage bioassays using adult Ochlerotatus taeniorhynchus (Wiedemann) investigated the effect of exposure time to a contaminated surface. Cages were dosed in a wind tunnel using the LC50 for naled (0.124 mg a.i./ml) and an LC25 (0.0772 mg a.i./ml) for naled. Half of the bioassay mosquitoes were moved directly into clean cages with the other half remaining in the sprayed, hence contaminated, cage. Treatment mortality was assessed at 8, 15, 30, 60, 120, 240, and 1,440 min postapplication. Cage contamination had a significant effect on mosquito mortality for both the LC25 and LC50 between 15 and 30 min postapplication.

Reconfigurable antennas radiations using plasma Faraday cage

OpenAIRE

Barro , Oumar Alassane; Himdi , Mohamed; Lafond , Olivier

2015-01-01

International audience; This letter presents a new reconfigurable plasma antenna associated with a Faraday cage. The Faraday cage is realized using a fluorescent lamp. A patch antenna with a broadside radiation pattern or a monopole antenna with an end-fire radiation pattern , operating at 2.45 GHz, is placed inside Faraday cage. The performance of the reconfigurable system is observed in terms of input reflection coefficient, gain and radiation pattern via simulation and measurement. It is s...

Cage culture of sea bass in Malaysia

OpenAIRE

1994-01-01

The article discusses the cage culture practice of sea bass (Lates calcarifer) in Malaysia. Problems on feed and seed supply and overcrowding are also discussed. Despite these problems, seabass cage culture still continuously booms.

Photoactivatable Caged Prodrugs of VEGFR-2 Kinase Inhibitors

Directory of Open Access Journals (Sweden)

Boris Pinchuk

2016-04-01

Full Text Available In this study, we report on the design, synthesis, photokinetic properties and in vitro evaluation of photoactivatable caged prodrugs for the receptor tyrosine kinase VEGFR-2. Highly potent VEGFR-2 inhibitors 1 and 3 were caged by introduction of a photoremovable protecting group (PPG to yield the caged prodrugs 4 and 5. As expected, enzymatic and cellular proliferation assays showed dramatically diminished efficacy of caged prodrugs in vitro. Upon ultraviolet (UV irradiation of the prodrugs original inhibitory activity was completely restored and even distinctly reinforced, as was the case for the prodrug 4. The presented results are a further evidence for caging technique being an interesting approach in the protein kinase field. It could enable spatial and temporal control for the inhibition of VEGFR-2. The described photoactivatable prodrugs might be highly useful as biological probes for studying the VEGFR-2 signal transduction.

High-throughput Transcriptome analysis, CAGE and beyond

KAUST Repository

Kodzius, Rimantas

2008-11-25

1. Current research - PhD work on discovery of new allergens - Postdoctoral work on Transcriptional Start Sites a) Tag based technologies allow higher throughput b) CAGE technology to define promoters c) CAGE data analysis to understand Transcription - Wo

High-throughput Transcriptome analysis, CAGE and beyond

KAUST Repository

Kodzius, Rimantas

2008-01-01

1. Current research - PhD work on discovery of new allergens - Postdoctoral work on Transcriptional Start Sites a) Tag based technologies allow higher throughput b) CAGE technology to define promoters c) CAGE data analysis to understand Transcription - Wo

Diversification of Protein Cage Structure Using Circularly Permuted Subunits.

Science.gov (United States)

Azuma, Yusuke; Herger, Michael; Hilvert, Donald

2018-01-17

Self-assembling protein cages are useful as nanoscale molecular containers for diverse applications in biotechnology and medicine. To expand the utility of such systems, there is considerable interest in customizing the structures of natural cage-forming proteins and designing new ones. Here we report that a circularly permuted variant of lumazine synthase, a cage-forming enzyme from Aquifex aeolicus (AaLS) affords versatile building blocks for the construction of nanocompartments that can be easily produced, tailored, and diversified. The topologically altered protein, cpAaLS, self-assembles into spherical and tubular cage structures with morphologies that can be controlled by the length of the linker connecting the native termini. Moreover, cpAaLS proteins integrate into wild-type and other engineered AaLS assemblies by coproduction in Escherichia coli to form patchwork cages. This coassembly strategy enables encapsulation of guest proteins in the lumen, modification of the exterior through genetic fusion, and tuning of the size and electrostatics of the compartments. This addition to the family of AaLS cages broadens the scope of this system for further applications and highlights the utility of circular permutation as a potentially general strategy for tailoring the properties of cage-forming proteins.

Homogenized boundary conditions and resonance effects in Faraday cages

Science.gov (United States)

Hewitt, I. J.

2016-01-01

We present a mathematical study of two-dimensional electrostatic and electromagnetic shielding by a cage of conducting wires (the so-called ‘Faraday cage effect’). Taking the limit as the number of wires in the cage tends to infinity, we use the asymptotic method of multiple scales to derive continuum models for the shielding, involving homogenized boundary conditions on an effective cage boundary. We show how the resulting models depend on key cage parameters such as the size and shape of the wires, and, in the electromagnetic case, on the frequency and polarization of the incident field. In the electromagnetic case, there are resonance effects, whereby at frequencies close to the natural frequencies of the equivalent solid shell, the presence of the cage actually amplifies the incident field, rather than shielding it. By appropriately modifying the continuum model, we calculate the modified resonant frequencies, and their associated peak amplitudes. We discuss applications to radiation containment in microwave ovens and acoustic scattering by perforated shells. PMID:27279775

Homogenized boundary conditions and resonance effects in Faraday cages

Science.gov (United States)

Hewett, D. P.; Hewitt, I. J.

2016-05-01

We present a mathematical study of two-dimensional electrostatic and electromagnetic shielding by a cage of conducting wires (the so-called `Faraday cage effect'). Taking the limit as the number of wires in the cage tends to infinity, we use the asymptotic method of multiple scales to derive continuum models for the shielding, involving homogenized boundary conditions on an effective cage boundary. We show how the resulting models depend on key cage parameters such as the size and shape of the wires, and, in the electromagnetic case, on the frequency and polarization of the incident field. In the electromagnetic case, there are resonance effects, whereby at frequencies close to the natural frequencies of the equivalent solid shell, the presence of the cage actually amplifies the incident field, rather than shielding it. By appropriately modifying the continuum model, we calculate the modified resonant frequencies, and their associated peak amplitudes. We discuss applications to radiation containment in microwave ovens and acoustic scattering by perforated shells.

Effects of cage density on behavior in young adult mice.

Science.gov (United States)

Davidson, Lauren P; Chedester, Alan L; Cole, Marlene N

2007-08-01

Optimal housing conditions for mice can be achieved by minimizing environmental variables, such as those that may contribute to anxiety-like behavior. This study evaluated the effects of cage size on juvenile mice through assessment of differences in weaning weight, locomotor skills, and anxiety-like behavior. Eighteen pairs of male and pregnant female Swiss-Webster (Cr:SW) mice were housed in 3 different caging scenarios, providing 429, 505, or 729 cm2 of space. Litters were standardized to 10 pups per litter in each cage. Mice reared in each caging scenario were assessed with the open-field, light-dark exploration, and elevated plus-maze tests. No differences in weaning weight were noted. Mice reared in the 505- and 729-cm2 cages explored a significantly larger area of the open-field arena than did those in the 429-cm2 cages. Those reared in the 505-cm2 cages spent more time in the center of the open field than did those in the 729-cm2 cages, suggesting that anxiety-like behavior may be increased in the animals housed in the larger cages. This study did not establish a consistent link between decreased floor space and increased anxiety-like behavior; neither does there appear to be a consistent effect of available floor area on the development of locomotor skills on mouse pups.

A New Approach for Optimal Sizing of Standalone Photovoltaic Systems

OpenAIRE

Khatib, Tamer; Mohamed, Azah; Sopian, K.; Mahmoud, M.

2012-01-01

This paper presents a new method for determining the optimal sizing of standalone photovoltaic (PV) system in terms of optimal sizing of PV array and battery storage. A standalone PV system energy flow is first analysed, and the MATLAB fitting tool is used to fit the resultant sizing curves in order to derive general formulas for optimal sizing of PV array and battery. In deriving the formulas for optimal sizing of PV array and battery, the data considered are based on five sites in Malaysia...

Zero-profile anchored cage reduces risk of postoperative dysphagia compared with cage with plate fixation after anterior cervical discectomy and fusion.

Science.gov (United States)

Xiao, ShanWen; Liang, ZhuDe; Wei, Wu; Ning, JinPei

2017-04-01

To compare the rate of postoperative dysphagia between zero-profile anchored cage fixation (ZPC group) and cage with plate fixation (CP group) after anterior cervical discectomy and fusion (ACDF). A meta-analysis of cohort studies between zero-profile anchored cage and conventional cage with plate fixation after ACDF for the treatment of cervical diseases from 2008 to May 2016. An extensive search of studies was performed in PubMed, Medline, Embase, Cochrane library and Google Scholar. Dysphagia rate was extracted. Data analysis was conducted with RevMan 5.2. Sixteen trials involving 1066 patients were included in this meta-analysis. The results suggested that the ZPC group were associated with lower incidences of dysphagia than the CP group at postoperative immediately, 2 weeks, 2, 3, 6 and 12 months. In subgroup analysis, although significant differences were only found in the mild dysphagia at 3 and 6 months postoperatively and in the moderate dysphagia at 2 weeks after surgery; the ZPC group had a lower rate of postoperative dysphagia than the CCP group in short, medium and long term follow-up periods. Zero-profile anchored cage had a lower risk of postoperative dysphagia than cage with plate.

Synthesis and Characterization of Polyfunctional Polyhedral Silsesquioxane Cages

Science.gov (United States)

Sulaiman, Santy

Recent studies on octameric polyhedral silsesquioxanes, (RSiO1.5 )8, indicate that the silsesquioxane cage is not just a passive component but appears to be involved in electron delocalization with conjugated organic tethers in the excited state. This dissertation presents the synthesis and characterization of (RSiO1.5)8 molecules with unique photophysical properties that provide support for the existence of conjugation that involves the (RSiO1.5)8 cage. The dissertation first discusses the elaboration of octavinylsilsesquioxane via cross-metathesis to form styrenyl-functionalized octasilsesquioxane molecules. Subsequent Heck coupling reactions of p-bromostyrenyl derivative provides vinylstilbene-functionalized octasilsesquioxane. The amino derivative, NH2VinylStilbeneOS, show highly red-shifted emission spectrum (100 nm from the simple organic analog p-vinylstilbene) and high two-photon absorption (TPA) cross-section value (100 GM/moiety), indicating charge-transfer processes involving the silsesquioxane cage as the electron acceptor. The unique photophysical properties of polyfunctional luminescent cubic silsesquioxanes synthesized from ortho-8-, (2,5)-16-, and 24-brominated octaphenylsilsesquioxane (OPS) via Heck coupling show how the steric interactions of the organic tethers at the silsesquioxane cage corner affect conjugation with the silsesquioxane cage. Furthermore, the high TPA cross-section (10 GM/moiety) and photoluminescence quantum yield (20%) of OPS functionalized with 24 acetoxystyrenyl groups suggest that the existence excited states in these molecules with similar energies and decay rates: normal radiative pi- pi* transition and charge transfer involving the silsesquioxane cage. The fluoride ion-catalyzed rearrangement reactions of cage and polymeric silsesquioxanes provide a convenient route to a mixture of deca- and dodecameric silsesquioxane molecules in high yields, giving us the opportunity to investigate the effect of silsesquioxane cage

Models for a stand-alone PV system

DEFF Research Database (Denmark)

Hansen, A.D.; Sørensen, Poul Ejnar; Hansen, L.H.

2001-01-01

are based on the model descriptions found in the literature. The battery model is developed at UMASS and is known as the Kinetic Battery Model(KiBaM). The other component models in the PV system are based on simple electrical knowledge. The implementation is done using Matlab/Simulink, a simulation program......This report presents a number of models for modelling and simulation of a stand-alone photovoltaic (PV) system with a battery bank verified against a system installed at Risø National Laboratory. The work has been supported by the Danish Ministry ofEnergy, as a part of the activities in the Solar...... Energy Centre Denmark. The study is carried out at Risø National Laboratory with the main purpose to establish a library of simple mathematical models for each individual element of a stand-alone PVsystem, namely solar cells, battery, controller, inverter and load. The models for PV module and battery...

Cloning simulation in the cage environment.

OpenAIRE

Douthart, R J; Thomas, J J; Rosier, S D; Schmaltz, J E; West, J W

1986-01-01

The CAGE/GEM(TM) software toolkit for genetic engineering is briefly described. The system functionally uses color graphics and is menu driven. It integrates genetics and features information ("Overlays") with information based on sequence analysis ("Representations"). The system is structured around CAD (Computer Aided Design) principles. The CAGE (Computer Aided Genetic Engineering) aspects of the software are emphasized and illustrated by a simulated cloning of the hepatitis B core antigen...

Stand-Alone Lateral Interbody Fusion for the Treatment of Low-Grade Degenerative Spondylolisthesis

Directory of Open Access Journals (Sweden)

Luis Marchi

2012-01-01

Full Text Available The purpose of this paper was to investigate the stand-alone lateral interbody fusion as a minimally invasive option for the treatment of low-grade degenerative spondylolisthesis with a minimum 24-month followup. Prospective nonrandomized observational single-center study. 52 consecutive patients (67.6±10 y/o; 73.1% female; 27.4±3.4 BMI with single-level grade I/II single-level degenerative spondylolisthesis without significant spine instability were included. Fusion procedures were performed as retroperitoneal lateral transpsoas interbody fusions without screw supplementation. The procedures were performed in average 73.2 minutes and with less than 50cc blood loss. VAS and Oswestry scores showed lasting improvements in clinical outcomes (60% and 54.5% change, resp.. The vertebral slippage was reduced in 90.4% of cases from mean values of 15.1% preoperatively to 7.4% at 6-week followup (P<0.001 and was maintained through 24 months (7.1%, P<0.001. Segmental lordosis (P<0.001 and disc height (P<0.001 were improved in postop evaluations. Cage subsidence occurred in 9/52 cases (17% and 7/52 cases (13% spine levels needed revision surgery. At the 24-month evaluation, solid fusion was observed in 86.5% of the levels treated. The minimally invasive lateral approach has been shown to be a safe and reproducible technique to treat low-grade degenerative spondylolisthesis.

Stand-alone XLIF

DEFF Research Database (Denmark)

Hansen, E. J.; Simony, A.; Hummel, Stefan

2015-01-01

and clinical/radiological results in 22 patients treated with XLIF procedure for DS or degenerative disc disease (DDD). Material and methods: 22 consecutive patients with DS underwent surgery with the XLIF stand-alone procedure, with follow-up of 24 months. Clinical outcome scores were collected. Complications......Introduction: Adult thoracolumbar degeneration is an increasing challenge in the aging population. With age the progressive degeneration of the discs leads to an asymmetric collapse and a thoracolumbar coronal plane deformity, a degenerative scoliosis (DS). Aim: To evaluate the complication rate......-year follow-up, with a 31.8% revision rate. Due to the high revision rate we recommend supplementary posterior instrumentation, to achieve a higher fusion rate. When considering XLIF-stand-alone procedure for DS or DDD without supplemental posterior instrumentation, only single-level disease should...

Caged Protein Prenyltransferase Substrates: Tools for Understanding Protein Prenylation

Energy Technology Data Exchange (ETDEWEB)

DeGraw, Amanda J.; Hast, Michael A.; Xu, Juhua; Mullen, Daniel; Beese, Lorena S.; Barany, George; Distefano, Mark D. (Duke); (UMM)

2010-11-15

Originally designed to block the prenylation of oncogenic Ras, inhibitors of protein farnesyltransferase currently in preclinical and clinical trials are showing efficacy in cancers with normal Ras. Blocking protein prenylation has also shown promise in the treatment of malaria, Chagas disease and progeria syndrome. A better understanding of the mechanism, targets and in vivo consequences of protein prenylation are needed to elucidate the mode of action of current PFTase (Protein Farnesyltransferase) inhibitors and to create more potent and selective compounds. Caged enzyme substrates are useful tools for understanding enzyme mechanism and biological function. Reported here is the synthesis and characterization of caged substrates of PFTase. The caged isoprenoid diphosphates are poor substrates prior to photolysis. The caged CAAX peptide is a true catalytically caged substrate of PFTase in that it is to not a substrate, yet is able to bind to the enzyme as established by inhibition studies and X-ray crystallography. Irradiation of the caged molecules with 350 nm light readily releases their cognate substrate and their photolysis products are benign. These properties highlight the utility of those analogs towards a variety of in vitro and in vivo applications.

Jules Verne's Metaphor of the Iron Cage

NARCIS (Netherlands)

Ossewaarde, Marinus R.R.

2010-01-01

Max Weber's concept of the iron cage has become a byword in the scholarly world since the publication in 1930 of Talcott Parsons’ translation of The Protestant Ethic and the Spirit of Capitalism. What is less well-known is that Jules Verne had earlier used the iron cage metaphor in Twenty Thousand

Clinical outcome of stand-alone ALIF compared to posterior instrumentation for degenerative disc disease

DEFF Research Database (Denmark)

Udby, Peter M.; Bech-Azeddine, Rachid

2015-01-01

The objective of the article was to: a) present results from a case cohort pilot study comparing stand-alone ALIF and TLIF and, b) review the literature on studies comparing the clinical outcome of stand-alone ALIF with posterior instrumentation including TLIF or PLIF, in patients with disabling...... low back pain resulting from degenerative disc disease. ALIF surgery has previously been linked with certain high risk complications and unfavorable long term fusion results. Newer studies suggest that stand-alone ALIF can possibly be advantageous compared to other types of posterior instrumented...

CAGE BREEDING OF WARM WATER FRESHWATER FISH SPECIES

Directory of Open Access Journals (Sweden)

Roman Safner

2008-10-01

Full Text Available In the 1970s, Croatia became actively involved in the contemporary trend of breeding fish in floating cages. In addition to various species of marine fishes, breeding was attempted with trout, carp, catfish, cisco and salmon. Of the above freshwater fish species, specific standards were established only for the cage breeding of rainbow trout. Cage breeding of the remaining species remained at the level of occasional attempts, with more of an experimental than a commercial character. The regular attempts to master this technique for cage breeding of warm water freshwater fish species were aimed at achieving the known benefits of such breeding, such as simplicity of implementing technological measures, easier establishment of the breeding system, simpler manipulation, the possibility of denser colonies per unit volume with a high level of production, easier adaptations to market conditions and fewer initial structural investments. Despite the many advantages, the main reasons for the lack of greater implementation of the cage breeding technology for warm water species of freshwater fish include problems in obtaining the appropriate category and quantity of healthy fry, the specificity and applicability of physical and chemical properties of the recipients and human error. In evaluating the advantages and disadvantages, the final decision on the justification of cage breeding for individual warm water freshwater species must be based on both biological and economic factors. Based on the knowledge of cage breeding acquired to date, the rule for virtually all intensive breeding systems is that it is only recommended for those species with high market demand and a high market price. The technology that demands nutrition with highly concentrated feed and other production expenditures is costly, and is therefore not profitable with less expensive fish species. Furthermore, production must be market oriented, i.e. the appropriate market research measures

Mitochondria mediate septin cage assembly to promote autophagy of Shigella.

Science.gov (United States)

Sirianni, Andrea; Krokowski, Sina; Lobato-Márquez, Damián; Buranyi, Stephen; Pfanzelter, Julia; Galea, Dieter; Willis, Alexandra; Culley, Siân; Henriques, Ricardo; Larrouy-Maumus, Gerald; Hollinshead, Michael; Sancho-Shimizu, Vanessa; Way, Michael; Mostowy, Serge

2016-07-01

Septins, cytoskeletal proteins with well-characterised roles in cytokinesis, form cage-like structures around cytosolic Shigella flexneri and promote their targeting to autophagosomes. However, the processes underlying septin cage assembly, and whether they influence S. flexneri proliferation, remain to be established. Using single-cell analysis, we show that the septin cages inhibit S. flexneri proliferation. To study mechanisms of septin cage assembly, we used proteomics and found mitochondrial proteins associate with septins in S. flexneri-infected cells. Strikingly, mitochondria associated with S. flexneri promote septin assembly into cages that entrap bacteria for autophagy. We demonstrate that the cytosolic GTPase dynamin-related protein 1 (Drp1) interacts with septins to enhance mitochondrial fission. To avoid autophagy, actin-polymerising Shigella fragment mitochondria to escape from septin caging. Our results demonstrate a role for mitochondria in anti-Shigella autophagy and uncover a fundamental link between septin assembly and mitochondria. © 2016 The Authors. Published under the terms of the CC BY 4.0 license.

Procedures for Determining the Performance of Stand-Alone Photovoltaic Systems; TOPICAL

International Nuclear Information System (INIS)

DeBlasio, R.; Durand, S.; Hansen, R.; Hutchinson, P.; Kroposki, B.; McNutt, P.; Rosenthal, A.; Thomas, M.

1999-01-01

This document provides the procedures for determining the performance of stand-alone PV systems. The procedures in this document provide a common approach for evaluating whether a given PV system is suitable to perform the function for which it was designed and manufactured to accomplish, and whether it will provide adequate power to run the load. These procedures cover small stand-alone PV systems. They cover complete outdoor system testing. Test results are valid only for the system that is tested

Effects of Furnished Cage Type on Behavior and Welfare of Laying Hens

Science.gov (United States)

Li, Xiang; Chen, Donghua; Li, Jianhong; Bao, Jun

2016-01-01

This study was conducted to compare the effects of layout of furniture (a perch, nest, and sandbox) in cages on behavior and welfare of hens. Two hundred and sixteen Hyline Brown laying hens were divided into five groups (treatments) with four replicates per group: small furnished cages (SFC), medium furnished cages type I (MFC-I), medium furnished cages type II (MFC-II), and medium furnished cages type III (MFC-III) and conventional cages (CC). The experiment started at 18 week of age and finished at 52 week of age. Hens’ behaviors were filmed during the following periods: 8:00 to 10:00; 13:00 to 14:00; 16:00 to 17:00 on three separate days and two hens from each cage were measured for welfare parameters at 50 wk of age. The results showed that feeding and laying of all hens showed no effect by cage type (p>0.05), and the hens in the furnished cages had significantly lower standing and higher walking than CC hens (phens between the furnished cages (p>0.05). The hens in MFC-I, −II, and −III showed a significant higher socializing behavior than SFC and CC (phens in SFC and the highest perching found for the hens in MFC-III. Overall, the hens in CC showed poorer welfare conditions than the furnished cages, in which the feather condition score, gait score and tonic immobility duration of the hens in CC was significantly higher than SFC, MFC-I, MFC-II, and MFC-III (phens. Overall, MFC-III cage design was better than SFC, MFC-I, and MFC-II cage designs. PMID:26954171

Extreme ultraviolet patterning of tin-oxo cages

Science.gov (United States)

Haitjema, Jarich; Zhang, Yu; Vockenhuber, Michaela; Kazazis, Dimitrios; Ekinci, Yasin; Brouwer, Albert M.

2017-07-01

We report on the extreme ultraviolet (EUV) patterning performance of tin-oxo cages. These cage molecules were already known to function as a negative tone photoresist for EUV radiation, but in this work, we significantly optimized their performance. Our results show that sensitivity and resolution are only meaningful photoresist parameters if the process conditions are optimized. We focus on contrast curves of the materials using large area EUV exposures and patterning of the cages using EUV interference lithography. It is shown that baking steps, such as postexposure baking, can significantly affect both the sensitivity and contrast in the open-frame experiments as well as the patterning experiments. A layer thickness increase reduced the necessary dose to induce a solubility change but decreased the patterning quality. The patterning experiments were affected by minor changes in processing conditions such as an increased rinsing time. In addition, we show that the anions of the cage can influence the sensitivity and quality of the patterning, probably through their effect on physical properties of the materials.

Stand-alone photovoltaic systems in the Netherlands. Evaluation of the market introduction

International Nuclear Information System (INIS)

Cloin, J.; Van Dijk, A.L.; Westra, C.A.

1999-08-01

The policy followed for stand-alone PV systems in the Netherlands is evaluated for the period 1997-1998. The world-wide powerful growth of the PV industry is not being followed by the increase in volume of implemented stand-alone PV systems in the Netherlands. This leads to the question whether the Dutch policy to stimulate stand-alone PV systems is effective. Recommendations on the use of communication as a strategic instrument are given, including the drawing up of a marketing plan. Other recommendations include increased transparency in the application for subsidies and a pro-active role of the Netherlands Agency for Energy and the Environment (Novem) in the contact with relevant market parties. The increased focus on product development aimed at the environmental benefits and general reliability of PV systems is recommended. 38 refs

Contamination trapped in a cage

International Nuclear Information System (INIS)

Sender, E.

2003-01-01

Some abandoned industrial sites are so strongly contaminated that they threaten to contaminate underground waters. Pollutants are driven through the soil by raining waters. The principle of the ''hydro-Faraday'' cage is to prevent raining waters from flowing through the contaminated part of the soil. The cage is in fact a structure of buried drain tubes that envelop the contaminated zone. Physics make waters flow through the tubes rather than the soil, so the contaminated zone receives no more water and as a consequence pollutants are stopped in their way towards the phreatic bed. (A.C.)

Extended cage adjustable speed electric motors and drive packages

Science.gov (United States)

Hsu, John S.

1999-01-01

The rotor cage of a motor is extended, a second stator is coupled to this extended rotor cage, and the windings have the same number of poles. The motor torque and speed can be controlled by either injecting energy into or extracting energy out from the rotor cage. The motor produces less harmonics than existing doubly-fed motors. Consequently, a new type of low cost, high efficiency drive is produced.

Modelling of synchronisation and energy performance of FBE- and LBE-based standalone LTE-U networks

Directory of Open Access Journals (Sweden)

Jiamin Li

2017-06-01

Full Text Available Without the aid of licensed channel, deploying long-term evolution (LTE networks over unlicensed spectrum (named standalone LTE-U networks faces the difficulty of establishing and maintaining synchronisation between user equipments and base stations. In this work, considering the two modes of listen-before-talk-based channel access scheme, frame-based equipment (FBE and load-based equipment (LBE, the authors propose analytical frameworks to study the successful probability of synchronisation and the energy consumption of synchronisation in a standalone LTE-U network. Specifically, for the LBE mode, the authors also propose a Lattice-Poisson algorithm-based approach to derive the distribution of the channel non-occupancy period of a standalone LTE-U network. Furthermore, the authors explore the impact of diverse protocol parameters of both FBE and LBE modes on the two studied performance metrics. Simulation results demonstrate the accuracy of the analysis, and shed some light on the selection of FBE and LBE for standalone LTE-U networks, in terms of synchronisation, energy consumption, and throughput of standalone LTE-U and Wi-Fi networks.

Effects of Furnished Cage Type on Behavior and Welfare of Laying Hens

Directory of Open Access Journals (Sweden)

Xiang Li

2016-06-01

Full Text Available This study was conducted to compare the effects of layout of furniture (a perch, nest, and sandbox in cages on behavior and welfare of hens. Two hundred and sixteen Hyline Brown laying hens were divided into five groups (treatments with four replicates per group: small furnished cages (SFC, medium furnished cages type I (MFC-I, medium furnished cages type II (MFC-II, and medium furnished cages type III (MFC-III and conventional cages (CC. The experiment started at 18 week of age and finished at 52 week of age. Hens’ behaviors were filmed during the following periods: 8:00 to 10:00; 13:00 to 14:00; 16:00 to 17:00 on three separate days and two hens from each cage were measured for welfare parameters at 50 wk of age. The results showed that feeding and laying of all hens showed no effect by cage type (p>0.05, and the hens in the furnished cages had significantly lower standing and higher walking than CC hens (p0.05. The hens in MFC-I, −II, and −III showed a significant higher socializing behavior than SFC and CC (p<0.05. The lowest perching was for the hens in SFC and the highest perching found for the hens in MFC-III. Overall, the hens in CC showed poorer welfare conditions than the furnished cages, in which the feather condition score, gait score and tonic immobility duration of the hens in CC was significantly higher than SFC, MFC-I, MFC-II, and MFC-III (p<0.05. In conclusion, the furnished cage design affected both behavior and welfare states of hens. Overall, MFC-III cage design was better than SFC, MFC-I, and MFC-II cage designs.

Effects of Furnished Cage Type on Behavior and Welfare of Laying Hens.

Science.gov (United States)

Li, Xiang; Chen, Donghua; Li, Jianhong; Bao, Jun

2016-06-01

This study was conducted to compare the effects of layout of furniture (a perch, nest, and sandbox) in cages on behavior and welfare of hens. Two hundred and sixteen Hyline Brown laying hens were divided into five groups (treatments) with four replicates per group: small furnished cages (SFC), medium furnished cages type I (MFC-I), medium furnished cages type II (MFC-II), and medium furnished cages type III (MFC-III) and conventional cages (CC). The experiment started at 18 week of age and finished at 52 week of age. Hens' behaviors were filmed during the following periods: 8:00 to 10:00; 13:00 to 14:00; 16:00 to 17:00 on three separate days and two hens from each cage were measured for welfare parameters at 50 wk of age. The results showed that feeding and laying of all hens showed no effect by cage type (p>0.05), and the hens in the furnished cages had significantly lower standing and higher walking than CC hens (p0.05). The hens in MFC-I, -II, and -III showed a significant higher socializing behavior than SFC and CC (p<0.05). The lowest perching was for the hens in SFC and the highest perching found for the hens in MFC-III. Overall, the hens in CC showed poorer welfare conditions than the furnished cages, in which the feather condition score, gait score and tonic immobility duration of the hens in CC was significantly higher than SFC, MFC-I, MFC-II, and MFC-III (p<0.05). In conclusion, the furnished cage design affected both behavior and welfare states of hens. Overall, MFC-III cage design was better than SFC, MFC-I, and MFC-II cage designs.

Cage occupancies of natural gas hydrates encaging methane and ethane

Energy Technology Data Exchange (ETDEWEB)

Kida, M.; Hachikubo, A.; Sakagami, H.; Minami, H.; Krylov, A.; Yamashita, S.; Takahashi, N.; Shoji, H. [Kitami Inst. of Technology, Kitami (Japan); Kida, M. [National Inst. of Advanced Industrial Science and Technology, Toyohira-ku, Sapporo (Japan); Khlystov, O. [Limnological Inst., Irkutsk (Russian Federation). Siberian Branch of the Russian Academy of Sciences; Poort, J. [Ghent Univ., Ghent (Belgium). Renard Centre of Marine Geology; Narita, H. [National Inst. of Advanced Industrial Science and Technology, Toyohira-ku, Sapporo (Japan)

2008-07-01

Natural gas hydrates are crystalline compounds that contain large amounts of natural gas in its structure and are expected to provide natural gas resources in the future. The gas species are trapped in different types of polyhedral cages which consist of hydrogen bonded water molecules. Three main types of crystallographic structures exist, notably structure 1, structure 2 and structure H (sH). The crystallographic structure of natural gas hydrates depends on the encaged gas components. The cage occupancy is the ratio of the number of cages occupied by guest molecules to the number of total cages. It is also important to estimate the amount of natural gas, since it depends on the condition of the hydrate formation such as gas composition. The cages of natural gas hydrates mainly contain methane. However, other heavier hydrocarbons such as ethane (C{sub 2}H{sub 6}), propane (C{sub 3}H{sub 8}), and isobutane (i-C{sub 4}H{sub 1}0) may be encaged together with CH{sub 4}. Little is known about cage occupancies of natural gas hydrates including CH{sub 4} and heavier hydrocarbons. This paper discussed a study that developed cage occupancy estimations of natural gas hydrates encaging heavier hydrocarbons. 13C nuclear magnetic resonance (NMR) measurements were conducted. The assignments of resonance lines were based on 13C chemical shifts obtained by artificial sample measurements. The paper presented the experimental data and discussed the results of the study. The large cages were almost fully occupied with CH{sub 4} and C{sub 2}H{sub 6} molecules, whereas the small cage occupancies of CH{sub 4} were below 0.8. The distribution of CH{sub 4} and C{sub 2}H{sub 6} in each cage were similar to that of synthetic CH{sub 4} + C{sub 2}H{sub 6} hydrate. It was concluded that these results should be useful for optimal estimation of the amount of natural gas in gas hydrates. 18 refs., 1 tab., 3 figs.

Chaotic Dynamics of Cage Behavior in a High-Speed Cylindrical Roller Bearing

Directory of Open Access Journals (Sweden)

Long Chen

2016-01-01

Full Text Available This paper presents a mathematical model to investigate the nonlinear dynamic behavior of cage in high-speed cylindrical bearing. Variations of cage behavior due to varying cage eccentricity and cage guidance gap are observed. Hydrodynamic behavior in cage contacts is taken into consideration for a more realistic calculation of acting forces owing to high working speed. Analysis of real-time cage dynamic behavior on radial plane is carried out using chaos theory based on the theoretical and mathematical model established in the paper. The analytical results of this paper provide a solid foundation for designing and manufacturing of high-speed cylindrical roller bearing.

Models for a stand-alone PV system[Photovoltaic

Energy Technology Data Exchange (ETDEWEB)

Hansen, A.D.; Soerensen, P.; Hansen, L.H.; Bindner, H.

2000-12-01

This report presents a number of models for modelling and simulation of a stand-alone photovoltaic (PV) system with a battery bank verified against a system installed at Risoe National Laboratory. The work has been supported by the Danish Ministry of Energy, as a part of the activities in the Solar Energy Centre Denmark. The study is carried out at Risoe National Laboratory with the main purpose to establish a library of simple mathematical models for each individual element of a stand-alone PV system, namely solar cells, battery, controller, inverter and load. The models for PV module and battery are based on the model descriptions found in the literature. The battery model is developed at UMASS and is known as the Kinetic Battery Model (KiBaM). The other component models in the PV system are based on simple electrical knowledge. The implementation is done using Matlab/Simulink, a simulation program that provides a graphical interface for building models as modular block diagrams. The non-linear behaviour of the battery, observed in the measurements, is investigated and compared to the KiBaM model's performance. A set of linear Black box models are estimated based on the battery measurements. The performance of the best linear Black box model is compared to the KiBaM model. A validation of each of the implemented mathematical model is performed by an interactive analysis and comparison between simulation results and measurements, acquired from the stand-alone PV system at Risoe. (au)

The polymethyl methacrylate cervical cage for treatment of cervical disk disease Part III. Biomechanical properties.

Science.gov (United States)

Chen, Jyi-Feng; Lee, Shih-Tseng

2006-10-01

In a previous article, we used the PMMA cervical cage in the treatment of single-level cervical disk disease and the preliminary clinical results were satisfactory. However, the mechanical properties of the PMMA cage were not clear. Therefore, we designed a comparative in vitro biomechanical study to determine the mechanical properties of the PMMA cage. The PMMA cervical cage and the Solis PEEK cervical cage were compressed in a materials testing machine to determine the mechanical properties. The compressive yield strength of the PMMA cage (7030 +/- 637 N) was less than that of the Solis polymer cervical cage (8100 +/- 572 N). The ultimate compressive strength of the PMMA cage (8160 +/- 724 N) was less than that of the Solis cage (9100 +/- 634 N). The stiffness of the PMMA cervical cage (8106 +/- 817 N/mm) was greater than that of the Solis cage (6486 +/- 530 N/mm). The elastic modulus of the PMMA cage (623 +/- 57 MPa) was greater than that of the Solis cage (510 +/- 42 MPa). The elongation of PMMA cage (43.5 +/- 5.7%) was larger than that of the Solis cage (36.1 +/- 4.3%). Although the compressive yield strength and ultimate compressive strength of the PMMA cervical cage were less than those of the Solis polymer cage, the mechanical properties are better than those of the cervical vertebral body. The PMMA cage is strong and safe for use as a spacer for cervical interbody fusion. Compared with other cage materials, the PMMA cage has many advantages and no obvious failings at present. However, the PMMA cervical cage warrants further long-term clinical study.

Stand-alone induction generators for small water power schemes

Energy Technology Data Exchange (ETDEWEB)

Harvey, Adam [Intermediate Technology Development Group, Rugby (United Kingdom); Smith, Nigel [Smith Associates, Nottingham (United Kingdom)

1996-04-01

Conventional technology for isolated power generation is the synchronous generator. Using stand-alone induction generators has proved to have tremendous advantages in remote regions of developing countries, where electricity has significant social benefits. (author)

Enzyme Treatment-Free and Ligation-Independent Cloning Using Caged Primers in Polymerase Chain Reactions

Directory of Open Access Journals (Sweden)

Akinori Kuzuya

2011-12-01

Full Text Available A new simple scheme for constructing recombinant vectors that does not require any restriction enzyme, ligase, or any other special enzyme treatment has been developed. By using caged primers in PCR, unnatural sticky-ends of any sequence, which are sufficiently long for ligation-independent cloning (LIC, are directly prepared on the product after a brief UVA irradiation. Target genes and vectors amplified by this light-assisted cohesive-ending (LACE PCR join together in the desired arrangement in a simple mixture of them, tightly enough to be repaired and ligated in competent cells.

Design and analysis of roll cage

Science.gov (United States)

Angadi, Gurusangappa; Chetan, S.

2018-04-01

Wildlife fire fighting vehicles are used to extinguish fires in forests, in this process vehicles face falling objects like rocks, tree branches and other objects. Also due to uneven conditions of the terrain like cliff edges, uneven surfaces etc. makes the vehicle to roll over and these can cause injuries to both the driver and the operator. Roll over of a vehicle is a common incident which makes fatal injuries to the operator and also stands next to the crash accidents. In order to reduce the injury level and continuous roll over of the vehicle it is necessary to equip suitable roll cage according to standards of vehicle. In this present work roll cage for pump operator in wildfire fighting vehicle is designed and analysis is carried out in computer simulated environment when seating position of operator seated outside of the cabin. According to NFPA 1906 standards wildlife fire apparatus, Design and Test procedures that are carried out in Hyperworks maintaining SAE J1194.1983 standards. G load case, roof crush analysis and pendulum impact analysis tests are carried out on roll cage to ensure the saftey of design. These load cases are considerd to satisfy the situation faced in forest terrain. In these test procedures roll cage is analysed for stresses and deformation in various load cases. After recording results these are compared with standards mentioned in SAE J1194.1983.

Effect of 2 Bedding Materials on Ammonia Levels in Individually Ventilated Cages.

Science.gov (United States)

Koontz, Jason M; Kumsher, David M; Kelly, Richard; Stallings, Jonathan D

2016-01-01

This study sought to identify an optimal rodent bedding and cage-change interval to establish standard procedures for the IVC in our rodent vivarium. Disposable cages were prefilled with either corncob or α-cellulose bedding and were used to house 2 adult Sprague-Dawley rats (experimental condition) or contained no animals (control). Rats were observed and intracage ammonia levels measured daily for 21 d. Intracage ammonia accumulation became significant by day 8 in experimental cages containing α-cellulose bedding, whereas experimental cages containing corncob bedding did not reach detectable levels of ammonia until day 14. In all 3 experimental cages containing α-cellulose, ammonia exceeded 100 ppm (our maximum acceptable limit) by day 11. Two experimental corncob cages required changing at days 16 and 17, whereas the remaining cage containing corncob bedding lasted the entire 21 d without reaching the 100-ppm ammonia threshold. These data suggests that corncob bedding provides nearly twice the service life of α-cellulose bedding in the IVC system.

A high-precision instrument for analyzing nonlinear dynamic behavior of bearing cage

Energy Technology Data Exchange (ETDEWEB)

Yang, Z., E-mail: zhaohui@nwpu.edu.cn; Yu, T. [School of Aeronautics, Northwestern Polytechnical University, Xi’an 710072 (China); Chen, H. [Xi’an Aerospace Propulsion Institute, Xi’an 710100 (China); Li, B. [State Key Laboratory for Manufacturing and Systems Engineering, Xi’an Jiaotong University, Xi’an 710054 (China)

2016-08-15

The high-precision ball bearing is fundamental to the performance of complex mechanical systems. As the speed increases, the cage behavior becomes a key factor in influencing the bearing performance, especially life and reliability. This paper develops a high-precision instrument for analyzing nonlinear dynamic behavior of the bearing cage. The trajectory of the rotational center and non-repetitive run-out (NRRO) of the cage are used to evaluate the instability of cage motion. This instrument applied an aerostatic spindle to support and spin test the bearing to decrease the influence of system error. Then, a high-speed camera is used to capture images when the bearing works at high speeds. A 3D trajectory tracking software TEMA Motion is used to track the spot which marked the cage surface. Finally, by developing the MATLAB program, a Lissajous’ figure was used to evaluate the nonlinear dynamic behavior of the cage with different speeds. The trajectory of rotational center and NRRO of the cage with various speeds are analyzed. The results can be used to predict the initial failure and optimize cage structural parameters. In addition, the repeatability precision of instrument is also validated. In the future, the motorized spindle will be applied to increase testing speed and image processing algorithms will be developed to analyze the trajectory of the cage.

A high-precision instrument for analyzing nonlinear dynamic behavior of bearing cage

International Nuclear Information System (INIS)

Yang, Z.; Yu, T.; Chen, H.; Li, B.

2016-01-01

The high-precision ball bearing is fundamental to the performance of complex mechanical systems. As the speed increases, the cage behavior becomes a key factor in influencing the bearing performance, especially life and reliability. This paper develops a high-precision instrument for analyzing nonlinear dynamic behavior of the bearing cage. The trajectory of the rotational center and non-repetitive run-out (NRRO) of the cage are used to evaluate the instability of cage motion. This instrument applied an aerostatic spindle to support and spin test the bearing to decrease the influence of system error. Then, a high-speed camera is used to capture images when the bearing works at high speeds. A 3D trajectory tracking software TEMA Motion is used to track the spot which marked the cage surface. Finally, by developing the MATLAB program, a Lissajous’ figure was used to evaluate the nonlinear dynamic behavior of the cage with different speeds. The trajectory of rotational center and NRRO of the cage with various speeds are analyzed. The results can be used to predict the initial failure and optimize cage structural parameters. In addition, the repeatability precision of instrument is also validated. In the future, the motorized spindle will be applied to increase testing speed and image processing algorithms will be developed to analyze the trajectory of the cage.

A review on recent size optimization methodologies for standalone solar and wind hybrid renewable energy system

International Nuclear Information System (INIS)

Al-falahi, Monaaf D.A.; Jayasinghe, S.D.G.; Enshaei, H.

2017-01-01

Highlights: • Possible combinations and configurations for standalone PV-WT HES were discussed. • Most recently used assessment parameters for standalone PV-WT HES were explained. • Optimization algorithms and software tools were comprehensively reviewed. • The recent trend of using hybrid algorithms over single algorithms was discussed. • Optimization algorithms for sizing standalone PV-WT HES were critically compared. - Abstract: Electricity demand in remote and island areas are generally supplied by diesel or other fossil fuel based generation systems. Nevertheless, due to the increasing cost and harmful emissions of fossil fuels there is a growing trend to use standalone hybrid renewable energy systems (HRESs). Due to the complementary characteristics, matured technologies and availability in most areas, hybrid systems with solar and wind energy have become the popular choice in such applications. However, the intermittency and high net present cost are the challenges associated with solar and wind energy systems. In this context, optimal sizing is a key factor to attain a reliable supply at a low cost through these standalone systems. Therefore, there has been a growing interest to develop algorithms for size optimization in standalone HRESs. The optimal sizing methodologies reported so far can be broadly categorized as classical algorithms, modern techniques and software tools. Modern techniques, based on single artificial intelligence (AI) algorithms, are becoming more popular than classical algorithms owing to their capabilities in solving complex optimization problems. Moreover, in recent years, there has been a clear trend to use hybrid algorithms over single algorithms mainly due to their ability to provide more promising optimization results. This paper aims to present a comprehensive review on recent developments in size optimization methodologies, as well as a critical comparison of single algorithms, hybrid algorithms, and software tools

Photoionization of atoms encapsulated by cages using the power-exponential potential

International Nuclear Information System (INIS)

Lin, C Y; Ho, Y K

2012-01-01

The systems of confined atoms in cages have received considerable attention for decades due to interesting phenomena arising from the effect of cage environment on the atom. For early theoretical work based on empirical model potentials, the Dirac δ-potential, i.e. the so-called bubble potential, and the attractive short-range spherical shell potential are conventionally used for the description of interaction between the valence electron of confined atom and the cage. In this work, the power-exponential potential with a flexible confining shape is proposed to model the cages. The methods of complex scaling in the finite-element discrete variable representation are implemented to investigate the hydrogen, hydrogen-like ions and alkali metals encapsulated by the cages. The energy spectrum varying with the confining well depth exhibits avoided crossings. The influence of cage on atomic photoionization leading to the oscillation behaviour or the so-called confinement resonances in cross sections is demonstrated in a variety of confined atomic systems. In comparisons with existing predictions using the Dirac δ-potential and the attractive short-range spherical shell potentials, our results show the significant influence of cage thickness and smooth shell boundary on the photoionization. The drastic changes of cross sections due to the character of cage are presented and discussed for the encaged lithium and sodium atoms. The present model is useful for clarifying the boundary effect of confining shell on the endohedral atoms. (paper)

Towards ubiquitous access of computer-assisted surgery systems.

Science.gov (United States)

Liu, Hui; Lufei, Hanping; Shi, Weishong; Chaudhary, Vipin

2006-01-01

Traditional stand-alone computer-assisted surgery (CAS) systems impede the ubiquitous and simultaneous access by multiple users. With advances in computing and networking technologies, ubiquitous access to CAS systems becomes possible and promising. Based on our preliminary work, CASMIL, a stand-alone CAS server developed at Wayne State University, we propose a novel mobile CAS system, UbiCAS, which allows surgeons to retrieve, review and interpret multimodal medical images, and to perform some critical neurosurgical procedures on heterogeneous devices from anywhere at anytime. Furthermore, various optimization techniques, including caching, prefetching, pseudo-streaming-model, and compression, are used to guarantee the QoS of the UbiCAS system. UbiCAS enables doctors at remote locations to actively participate remote surgeries, share patient information in real time before, during, and after the surgery.

Digestibility and behavior of dogs housed in kennels or metabolic cages

Directory of Open Access Journals (Sweden)

Tabyta Tamara Sabchuk

2012-01-01

Full Text Available The objective of the present study was to compare the apparent digestibility coefficients of a commercial dog food, fecal consistency and behavior of dogs housed in kennels and metabolic cages. Six adult Beagle dogs were distributed in cross-over experimental design, with six replicates per treatment. Dogs were housed in two environments: metabolic cages and in masonry kennels with solarium. Dogs were fed for a five-day adaptation period, and the five following days were used for total feces collection. Dogs behavior was recorded during a 48-h period, with 10-min intervals. Apparent digestibility coefficients were not different between treatments. However, dogs housed in metabolic cages produced lower weight and more consistent feces as compared with dogs housed in kennels. Dogs spent most of the time sleeping in both housing systems; however, dogs housed in the metabolic cages slept more than those in kennels. Stress-related behaviors (barking, whimpering, stereotypies, etc were observed for no longer than 15 minutes per day, and were not different between dogs in kennels or in cages. There is no difference in food digestibility evaluated in dogs housed in metabolic cages or kennels; however, dogs kept in metabolic cages eliminate drier feces and spend more time inactive than those kept in kennels.

Connecting embedded and stand-alone peer mentoring models to enhance student engagement

Directory of Open Access Journals (Sweden)

Rhys Cooper

2018-03-01

Full Text Available This paper outlines the Trident Student Mentoring Program that runs in the College of Engineering at Victoria University, Melbourne, Australia. The program offers both embedded and stand-alone models of peer mentoring services to the same cohort of first-year students. It shows that by forming strong links between these two types of peer mentoring models, the inherent challenges of both, such as low attendance rates in stand-alone models and short periods of peer to peer time in embedded models, are mitigated.

Sensorless direct voltage control of the stand-alone brushless doubly-fed generator

DEFF Research Database (Denmark)

Liu, Yi; Xu, Wei; Xiong, Fei

2017-01-01

The conventional stand-alone brushless doubly-fed generator (BDFG) control strategies need the feedback from the rotor position or speed sensors, which can reduce system reliability and increase the cost and axial volume of the machine. In this paper, a sensorless direct voltage control (DVC) str......) strategy is presented for the stand-alone BDFG. The satisfactory dynamic performance is verified by experimental results under four kinds of typical operation conditions. Besides, the proposed control strategy is robust due to no generator parameters being required....

Anisotropy and memory during cage breaking events close to a wall

International Nuclear Information System (INIS)

Kohl, Matthias; Härtel, Andreas; Schmiedeberg, Michael

2016-01-01

The slow dynamics in a glassy hard-sphere system is dominated by cage breaking events, i.e. rearrangements where a particle escapes from the cage formed by its neighboring particles. We study such events for an overdamped colloidal system by the means of Brownian dynamics simulations. While it is difficult to relate cage breaking events to structural mean field results in bulk, we show that the microscopic dynamics of particles close to a wall can be related to the anisotropic two-particle density. In particular, we study cage-breaking trajectories, mean forces on a tracked particle, and the impact of the history of trajectories. Based on our simulation results, we further construct two different one-particle random-walk models—one without and one with memory incorporated—and find the local anisotropy and the history-dependence of particles as crucial ingredients to describe the escape from a cage. Finally, our detailed study of a rearrangement event close to a wall not only reveals the memory effect of cages, but leads to a deeper insight into the fundamental mechanisms of glassy dynamics. (paper)

Mouse housing system using pressurized cages intraventilated by direct-current microfans.

Science.gov (United States)

Martinewski, Alexandre; Correia, Caio S C; de Souza, Nívea L; Merusse, José L B

2012-03-01

We performed the initial assessment of an alternative pressurized intraventilated (PIV) caging system for laboratory mice that uses direct-current microfans to achieve cage pressurization and ventilation. Twenty-nine pairs of female SPF BALB/c mice were used, with 19 experimental pairs kept in PIV cages and 10 control pairs kept in regular filter-top (FT) cages. Both groups were housed in a standard housing room with a conventional atmospheric control system. For both systems, intracage temperatures were in equilibrium with ambient room temperature. PIV cages showed a significant difference in pressure between days 1 and 8. Air speed (and consequently airflow rate) and the number of air changes hourly in the PIV cages showed decreasing trends. In both systems, ammonia concentrations increased with time, with significant differences between groups starting on day 1. Overall, the data revealed that intracage pressurization and ventilation by using microfans is a simple, reliable system, with low cost, maintenance requirements, and incidence of failures. Further experiments are needed to determine the potential influence of this system on the reproductive performance and pulmonary integrity in mice.

Stand-alone solutions, computer networks and extern communications

International Nuclear Information System (INIS)

Tarschisch, H.

1988-01-01

The advantages of local networks over stand-alone solutions are presented. Of the local networks (LAN), two are presently at the center of attention: the bus and the ring. ETHERNET and the IBM-Token-Ring are described as typical examples. Access to public networks, especially TELEPAC and ISDN, is discussed. 12 figs

Standalone General Purpose Data Logger Design and Implementation

African Journals Online (AJOL)

This paper describes the design of a general purpose data logger that is compatible with a variety of transducers, potentially permitting the measurement and recording of a wide range of phenomena. The recorded data can be retrieved to a PC via an RS-232 serial port. The standalone general purpose data logger ...

The effects of climbing cages on behaviour of female mink during the lactation period

DEFF Research Database (Denmark)

Lidfors, L.; Axelsson, H.; Loberg, J.

2012-01-01

=46) or standard cages (2.550 cm², n=44). Behavioural observations were made four weeks before birth until kits were nine weeks old with one-zero sampling during two hours before feeding. During week 1-4 after females had given birth they were mostly recorded in the nest box and there were......The aim was to investigate if there were differences in behaviour of female mink when kept in a climbing cage compared with a standard cage during the lactation period. The study was carried out on 90 mink of the colour type "black cross". Females were housed in either climbing cages (4.350 cm², n...... no differences between cage types. Week 5-8 after giving birth females in climbing cages were less in the nest box, less active out in the cage and had fewer abnormal behaviours, but were on the platforms and more inactive out in the cage. In the bottom cage females were more often walking, grooming and inactive...

Effect of space allowance and cage size on laying hens housed in furnished cages, Part I: Performance and well-being

Science.gov (United States)

Widowski, T. M; Caston, L. J; Hunniford, M. E; Cooley, L; Torrey, S

2017-01-01

Abstract There are few published data on the effects of housing laying hens at different densities in large furnished cages (FC; a.k.a. enriched colony cages). The objective of this study was to determine the effects of housing laying hens at 2 space allowances (SA) in 2 sizes of FC on measures of production and well-being. At 18 wk of age, 1,218 LSL-Lite hens were housed in cages furnished with a curtained nesting area, perches, and scratch mat, and stocked at either 520 cm2 (Low) or 748 cm2 (High) total floor space. This resulted in 4 group sizes: 40 vs. 28 birds in smaller FC (SFC) and 80 vs. 55 in larger FC (LFC). Data were collected from 20 to 72 wks of age. There was no effect of cage size (P = 0.21) or SA (P = 0.37) on hen day egg production, egg weight (PSize = 0.90; PSA = 0.73), or eggshell deformation (PSize = 0.14; PSA = 0.053), but feed disappearance was higher in SFC than LFC (P = 0.005). Mortality to 72 wk was not affected by cage size (P = 0.78) or SA (P = 0.55). BW (P = 0.006) and BW CV (P = 0.008) increased with age but were not affected by treatment. Feather cleanliness was poorer in FC with low SA vs. high (P hens housed at the lower space allowance may be compromised according to some welfare assessment criteria. PMID:29050408

A New Approach for Optimal Sizing of Standalone Photovoltaic Systems

Directory of Open Access Journals (Sweden)

Tamer Khatib

2012-01-01

Full Text Available This paper presents a new method for determining the optimal sizing of standalone photovoltaic (PV system in terms of optimal sizing of PV array and battery storage. A standalone PV system energy flow is first analysed, and the MATLAB fitting tool is used to fit the resultant sizing curves in order to derive general formulas for optimal sizing of PV array and battery. In deriving the formulas for optimal sizing of PV array and battery, the data considered are based on five sites in Malaysia, which are Kuala Lumpur, Johor Bharu, Ipoh, Kuching, and Alor Setar. Based on the results of the designed example for a PV system installed in Kuala Lumpur, the proposed method gives satisfactory optimal sizing results.

PROBLEMS OF BIOFOULING ON FISH–CAGE NETS IN AQUACULTURE

Directory of Open Access Journals (Sweden)

Merica Slišković

2002-09-01

Full Text Available Biofouling on fish–cage netting is a serious technical and economical problem to aquaculture worldwide. Compensation for the effects of biofouling must be included in cage system design and planning, as fouling can dramatically increase both weight and drag. Settlements of sessile plants and animals, with accumulation of the detritus diminish the size of mesh and can rapidly occlude mesh. Negative effect of smaller mesh size is changing in water flow trough the cages. Biofouling problems necessitating purchase of a second sets of nets or more, and frequent cleaning and changing of biofouling. Changing and cleaning frequency depend on many factors such as: location of cages (near the coast or off shore, productivity of that location, time of the year, time period in which the cages are placed on that location (cause of loading of phosphorus and nitrogen from the unconsumed food in the sediment. Net changing and cleaning procedures are labor and capital intensive. Process of the cleaning of the nets is inadequate, especially when there isnžt adequate equipment available as it is case in smaller aquaculture industry. Chemical control of biofouling e. g. use of antifoulants is questioningly cause of their possible negative effects on breeding species and environment.

FANTOM5 CAGE profiles of human and mouse samples

KAUST Repository

Noguchi, Shuhei

2017-08-29

In the FANTOM5 project, transcription initiation events across the human and mouse genomes were mapped at a single base-pair resolution and their frequencies were monitored by CAGE (Cap Analysis of Gene Expression) coupled with single-molecule sequencing. Approximately three thousands of samples, consisting of a variety of primary cells, tissues, cell lines, and time series samples during cell activation and development, were subjected to a uniform pipeline of CAGE data production. The analysis pipeline started by measuring RNA extracts to assess their quality, and continued to CAGE library production by using a robotic or a manual workflow, single molecule sequencing, and computational processing to generate frequencies of transcription initiation. Resulting data represents the consequence of transcriptional regulation in each analyzed state of mammalian cells. Non-overlapping peaks over the CAGE profiles, approximately 200,000 and 150,000 peaks for the human and mouse genomes, were identified and annotated to provide precise location of known promoters as well as novel ones, and to quantify their activities.

FANTOM5 CAGE profiles of human and mouse samples

KAUST Repository

Noguchi, Shuhei; Arakawa, Takahiro; Fukuda, Shiro; Furuno, Masaaki; Hasegawa, Akira; Hori, Fumi; Ishikawa-Kato, Sachi; Kaida, Kaoru; Kaiho, Ai; Kanamori-Katayama, Mutsumi; Kawashima, Tsugumi; Sakai, Mizuho; Simon, Christophe; Suzuki, Naoko; Tagami, Michihira; Watanabe, Shoko; Yoshida, Shigehiro; Arner, Peter; Axton, Richard A.; Babina, Magda; Baillie, J. Kenneth; Mummery, Christine L.; Barnett, Timothy C.; Beckhouse, Anthony G.; Blumenthal, Antje; Bodega, Beatrice; Bonetti, Alessandro; Briggs, James; Brombacher, Frank; Carlisle, Ailsa J.; Clevers, Hans C.; Davis, Carrie A.; Nakachi, Yutaka; Detmar, Michael; Dohi, Taeko; Edge, Albert S.B.; Edinger, Matthias; Ehrlund, Anna; Ekwall, Karl; Endoh, Mitsuhiro; Enomoto, Hideki; Eslami, Afsaneh; Fagiolini, Michela; Nakahara, Fumio; Fairbairn, Lynsey; Farach-Carson, Mary C.; Faulkner, Geoffrey J.; Ferrai, Carmelo; Fisher, Malcolm E.; Forrester, Lesley M.; Fujita, Rie; Furusawa, Jun-ichi; Geijtenbeek, Teunis B.; Gingeras, Thomas; Nakamura, Toshiyuki; Goldowitz, Daniel; Guhl, Sven; Guler, Reto; Gustincich, Stefano; Ha, Thomas J.; Hamaguchi, Masahide; Hara, Mitsuko; Hasegawa, Yuki; Herlyn, Meenhard; Heutink, Peter; Nakamura, Yukio; Hitchens, Kelly J.; Hume, David A.; Ikawa, Tomokatsu; Orlando, Valerio; Kai, Chieko; Kawamoto, Hiroshi; Kawamura, Yuki I.; Kempfle, Judith S.; Kenna, Tony J.; Kere, Juha; Nozaki, Tadasuke; Khachigian, Levon M.; Kitamura, Toshio; Klein, Sarah; Klinken, S. Peter; Knox, Alan J.; Kojima, Soichi; Koseki, Haruhiko; Koyasu, Shigeo; Lee, Weonju; Lennartsson, Andreas; Ogishima, Soichi; Mackay-sim, Alan; Mejhert, Niklas; Mizuno, Yosuke; Morikawa, Hiromasa; Morimoto, Mitsuru; Moro, Kazuyo; Morris, Kelly J.; Motohashi, Hozumi; Ohkura, Naganari; Ohno, Hiroshi; Ohshima, Mitsuhiro; Kojima, Miki; Okada-Hatakeyama, Mariko; Okazaki, Yasushi; Orlando, Valerio; Ovchinnikov, Dmitry A.; Passier, Robert; Patrikakis, Margaret; Pombo, Ana; Pradhan-Bhatt, Swati; Qin, Xian-Yang; Rehli, Michael; Kubosaki, Atsutaka; Rizzu, Patrizia; Roy, Sugata; Sajantila, Antti; Sakaguchi, Shimon; Sato, Hiroki; Satoh, Hironori; Savvi, Suzana; Saxena, Alka; Schmidl, Christian; Schneider, Claudio; Manabe, Ri-ichiroh; Schulze-Tanzil, Gundula G.; Schwegmann, Anita; Sheng, Guojun; Shin, Jay W.; Sugiyama, Daisuke; Sugiyama, Takaaki; Summers, Kim M.; Takahashi, Naoko; Takai, Jun; Tanaka, Hiroshi; Murata, Mitsuyoshi; Tatsukawa, Hideki; Tomoiu, Andru; Toyoda, Hiroo; van de Wetering, Marc; van den Berg, Linda M.; Verardo, Roberto; Vijayan, Dipti; Wells, Christine A.; Winteringham, Louise N.; Wolvetang, Ernst; Nagao-Sato, Sayaka; Yamaguchi, Yoko; Yamamoto, Masayuki; Yanagi-Mizuochi, Chiyo; Yoneda, Misako; Yonekura, Yohei; Zhang, Peter G.; Zucchelli, Silvia; Abugessaisa, Imad; Arner, Erik; Harshbarger, Jayson; Nakazato, Kenichi; Kondo, Atsushi; Lassmann, Timo; Lizio, Marina; Sahin, Serkan; Sengstag, Thierry; Severin, Jessica; Shimoji, Hisashi; Suzuki, Masanori; Suzuki, Harukazu; Kawai, Jun; Ninomiya, Noriko; Kondo, Naoto; Itoh, Masayoshi; Daub, Carsten O.; Kasukawa, Takeya; Kawaji, Hideya; Carninci, Piero; Forrest, Alistair R.R.; Hayashizaki, Yoshihide; Nishiyori-Sueki, Hiromi; Noma, Shohei; Saijyo, Eri; Saka, Akiko

2017-01-01

In the FANTOM5 project, transcription initiation events across the human and mouse genomes were mapped at a single base-pair resolution and their frequencies were monitored by CAGE (Cap Analysis of Gene Expression) coupled with single-molecule sequencing. Approximately three thousands of samples, consisting of a variety of primary cells, tissues, cell lines, and time series samples during cell activation and development, were subjected to a uniform pipeline of CAGE data production. The analysis pipeline started by measuring RNA extracts to assess their quality, and continued to CAGE library production by using a robotic or a manual workflow, single molecule sequencing, and computational processing to generate frequencies of transcription initiation. Resulting data represents the consequence of transcriptional regulation in each analyzed state of mammalian cells. Non-overlapping peaks over the CAGE profiles, approximately 200,000 and 150,000 peaks for the human and mouse genomes, were identified and annotated to provide precise location of known promoters as well as novel ones, and to quantify their activities.

Field cage studies and progressive evaluation of genetically-engineered mosquitoes.

Directory of Open Access Journals (Sweden)

Luca Facchinelli

Full Text Available A genetically-engineered strain of the dengue mosquito vector Aedes aegypti, designated OX3604C, was evaluated in large outdoor cage trials for its potential to improve dengue prevention efforts by inducing population suppression. OX3604C is engineered with a repressible genetic construct that causes a female-specific flightless phenotype. Wild-type females that mate with homozygous OX3604C males will not produce reproductive female offspring. Weekly introductions of OX3604C males eliminated all three targeted Ae. aegypti populations after 10-20 weeks in a previous laboratory cage experiment. As part of the phased, progressive evaluation of this technology, we carried out an assessment in large outdoor field enclosures in dengue endemic southern Mexico.OX3604C males were introduced weekly into field cages containing stable target populations, initially at 10:1 ratios. Statistically significant target population decreases were detected in 4 of 5 treatment cages after 17 weeks, but none of the treatment populations were eliminated. Mating competitiveness experiments, carried out to explore the discrepancy between lab and field cage results revealed a maximum mating disadvantage of up 59.1% for OX3604C males, which accounted for a significant part of the 97% fitness cost predicted by a mathematical model to be necessary to produce the field cage results.Our results indicate that OX3604C may not be effective in large-scale releases. A strain with the same transgene that is not encumbered by a large mating disadvantage, however, could have improved prospects for dengue prevention. Insights from large outdoor cage experiments may provide an important part of the progressive, stepwise evaluation of genetically-engineered mosquitoes.

Pop hole passages and welfare in furnished cages for laying hens.

Science.gov (United States)

Wall, H; Tauson, R; Elwinger, K

2004-02-01

1. This study included two designs of furnished cages for 16 hens; H-cages divided into two apartments by a partition with pop holes in the middle of the cage, and fully open O-cages, without a partition. The hypothesis was that in this rather large group of birds the pop hole partition would benefit the birds by allowing them to avoid or escape from potential cannibals, feather-peckers or aggressive hens. All cages had two nests, two perches and one litter box. 2. A total of 10 cages (5 H and 5 O) were stocked with Lohmann Selected Leghorn (LSL) and 8 cages (4 H and 4 O) with Hy-Line W36. No birds were beak-trimmed. 3. Heterophil/lymphocyte (H/L) ratios, duration of tonic immobility (TI) and exterior appearance (scoring of plumage condition and wounds at comb or around cloaca) were used as indicators of well-being. Total mortality and deaths due to cannibalism were also recorded. 4. Visits to nests and passages through partition pop holes were studied in samples of 35 and 21 birds, respectively, using a technique based on passive integrated transponder (PIT) tags. 5. Cage design (H- vs O-cage) had no effect on the welfare traits chosen. 6. Hy-Line birds showed higher H/L ratios, longer duration of TI and better plumage condition than LSL birds. These differences are discussed in terms of stress thresholds and copying strategies. 7. On days when a hen made visits to nests, the visiting frequency was 1.4 and the total time in the nest was 41 min on average. Hens made use of the pop hole passages between 1 and 8 times per hen and day. 8. Overall low levels of aggression, lack of injuries or deaths due to cannibalism, and plumage condition indicating moderate feather pecking, together imply a low need to escape. The pop holes were used frequently and birds distributed well between compartments showing that the system worked well. However, at this group size there was no evidence in the measured traits that H-cages provided a better housing environment.

A Squirrel Cage Type Electric Motor Rotor Assembly.

Science.gov (United States)

1996-09-05

cage motor, but also provides efficiencies approaching those of permanent magnet motors . With the above and other objects in view, as will...and active motor life relative to known permanent magnet motors . Referring to FIG. 4, there is illustrated an alternative embodiment in which...part the.known advantages of a squirrel cage motor, and further provides improved efficiencies approaching those of permanent magnet motors . It is to

48 CFR 252.204-7001 - Commercial and Government Entity (CAGE) code reporting.

Science.gov (United States)

2010-10-01

... Entity (CAGE) code reporting. 252.204-7001 Section 252.204-7001 Federal Acquisition Regulations System... Entity (CAGE) Code Reporting (AUG 1999) (a) The offeror is requested to enter its CAGE code on its offer... AND CONTRACT CLAUSES Text of Provisions And Clauses 252.204-7001 Commercial and Government Entity...

Encapsulation of cobalt nanoparticles in cross-linked-polymer cages

Energy Technology Data Exchange (ETDEWEB)

Hatamie, Shadie [Department of Electronic-Science, Fergusson College, Pune 411 004 (India); Dhole, S.D. [Department of Physics, University of Pune, Pune 411 007 (India); Ding, J. [Department of Materials Science and Engineering, National University of Singapore, 7, Engineering Drive 1, Singapore 117574 (Singapore); Kale, S.N. [Department of Electronic-Science, Fergusson College, Pune 411 004 (India)], E-mail: sangeetakale2004@gmail.com

2009-07-15

Nanoparticles embedded in polymeric cages give rise to interesting applications ranging from nanocatalysis to drug-delivery systems. In this context, we report on synthesis of cobalt (Co) nanoparticles trapped in polyvinyl alcohol (PVA) matrix to yield self-supporting magnetic films in PVA slime. A 20 nm, Co formed in FCC geometry encapsulated with a weak citrate coat when caged in PVA matrix exhibited persistence of magnetism and good radio-frequency response. Cross-linking of PVA chains to form cage-like structures to arrest Co nanoparticles therein, is believed to be the reason for oxide-free nature of Co, promising applications in biomedicine as well as in radio-frequency shielding.

The stand-alone test and decreasing serial cost sharing

DEFF Research Database (Denmark)

Hougaard, Jens Leth; Thorlund-Petersen, Lars

2000-01-01

The rule of decreasing serial cost sharing defined in de Frutos [1] over the class of concave cost functions may violate the important stand-alone test. Sufficient conditions for the test to be satisfied are given, in terms of individual rationality as well as coalitional stability...

Stand-alone version of the 11kW Gaia wind turbine

Energy Technology Data Exchange (ETDEWEB)

Bindner, H.; Rosas, P.A.C.; Teodorescu, R.; Blaabjerg, F.

2004-09-15

This report describes the development of a stand-alone version of the 11kW Gaia wind turbine. Various possible configurations are investigated and a configuration using a back-to-back converter is chosen. A model is developed for controller design of the fast controllers of the unit. Controllers are designed and a prototype is built for testing. The report documents the performance of the prototype through measurements done on the full scale prototype installed in a test facility where it has been tested both as a standalone unit and in parallel with a diesel genset. For system wide power quality assessment and controller design a dynamic performance assessment model has been developed. (au)

Comparison of Expandable and Fixed Interbody Cages in a Human Cadaver Corpectomy Model: Fatigue Characteristics.

Science.gov (United States)

Pekmezci, Murat; Tang, Jessica A; Cheng, Liu; Modak, Ashin; McClellan, Robert T; Buckley, Jenni M; Ames, Christopher P

2016-11-01

In vitro cadaver biomechanics study. The goal of this study is to compare the in situ fatigue life of expandable versus fixed interbody cage designs. Expandable cages are becoming more popular, in large part, due to their versatility; however, subsidence and catastrophic failure remain a concern. This in vitro analysis investigates the fatigue life of expandable and fixed interbody cages in a single level human cadaver corpectomy model by evaluating modes of subsidence of expandable and fixed cages as well as change in stiffness of the constructs with cyclic loading. Nineteen specimens from 10 human thoracolumbar spines (T10-L2, L3-L5) were biomechanically evaluated after a single level corpectomy that was reconstructed with an expandable or fixed cage and anterior dual rod instrumentation. All specimens underwent 98 K cycles to simulate 3 months of postoperative weight bearing. In addition, a third group with hyperlordotic cages was used to simulate catastrophic failure that is observed in clinical practice. Three fixed and 2 expandable cages withstood the cyclic loading despite perfect sagittal and coronal plane fitting of the endcaps. The majority of the constructs settled in after initial subsidence. The catastrophic failures that were observed in clinical practice could not be reproduced with hyperlordotic cages. However, all cages in this group subsided, and 60% resulted in endplate fractures during deployment of the cage. Despite greater surface contact area, expandable cages have a trend for higher subsidence rates when compared with fixed cages. When there is edge loading as in the hyperlordotic cage scenario, there is a higher risk of subsidence and intraoperative fracture during deployment of expandable cages.

Harmonics reduction in standalone DFIG-DC system by shunt active ...

Indian Academy of Sciences (India)

Himanshu Misra

2018-05-22

May 22, 2018 ... Doubly fed induction generator; standalone; DC voltage regulation; shunt active filter; harmonics ... Operation and design issue of DFIG in DC-net interface is ...... control systems for the operation of DFIGs in wind energy.

Mosquito density, biting rate and cage size effects on repellent tests.

Science.gov (United States)

Barnard, D R; Posey, K H; Smith, D; Schreck, C E

1998-01-01

Mosquito biting rates and the mean duration of protection (in hours) from bites (MDPB) of Aedes aegypti and Anopheles quadrimaculatus, using the repellent 'deet' (N,N-diethyl-3-methylbenzamide) on a 50 cm2 area of healthy human skin, were observed in small (27 l), medium (approximately 65 l) and large (125 l) cages containing low, medium or high densities of mosquitoes: respectively, 640, 128 or 49 cm3 of cage volume per female. At the initial treatment rate of approximately 0.4 microliter/cm2 (1 ml of 25% deet in ethanol on 650 cm2 of skin), the MDPB for deet against Ae. aegypti ranged from 4.5 to 6.5 h and was significantly less (5.0 +/- 0.8 h) in large cages compared with medium (6.2 +/- 0.9 h) and small (6.2 +/- 0.8 h) cages, regardless of the density. Against An. quadrimaculatus the MDPB for deet 0.4 microliter/cm2 was 1.5-8.0 h, less in small (3.7 +/- 2.3 h) and large (2.2 +/- 1.1 h) cages at medium (3.7 +/- 2.3 h) and high (2.5 +/- 1.7 h) mosquito densities, and was longest in medium cages (6.2 +/- 2.6 h) at low mosquito densities (5.8 +/- 2.8 h). With equinoxial photoperiodicity (light on 06.00-18.00 hours) the biting rate was influenced by the time of observation (08.00, 12.00, 16.00 hours) for Ae. aegypti but not for An. quadrimaculatus. For both species, the biting rate was inversely proportional to mosquito density and the MDPB. The shortest MDPBs were obtained in large cages with high densities of mosquitoes and longest protection times occurred in medium sized cages with low mosquito densities.

Mice Do Not Habituate to Metabolism Cage Housing

DEFF Research Database (Denmark)

Kalliokoski, Otto; Jacobsen, Kirsten Rosenmaj; Darusman, Huda Shalahudin

2013-01-01

The metabolism cage is a barren, non-enriched, environment, combining a number of recognized environmental stressors. We investigated the ability of male BALB/c mice to acclimatize to this form of housing. For three weeks markers of acute and oxidative stress, as well as clinical signs of abnorma...... metabolism warrant caution when interpreting data obtained from metabolism cage housed mice, as their condition cannot be considered representative of a normal physiology....

More vertical etch profile using a Faraday cage in plasma etching

Science.gov (United States)

Cho, Byeong-Ok; Hwang, Sung-Wook; Ryu, Jung-Hyun; Moon, Sang Heup

1999-05-01

Scanning electron microscope images of sidewalls obtained by plasma etching of an SiO2 film with and without a Faraday cage have been compared. When the substrate film is etched in the Faraday cage, faceting is effectively suppressed and the etch profile becomes more vertical regardless of the process conditions. This is because the electric potential in the cage is nearly uniform and therefore distortion of the electric field at the convex corner of a microfeature is prevented. The most vertical etch profile is obtained when the cage is used in fluorocarbon plasmas, where faceting is further suppressed due to the decrease in the chemical sputtering yield and the increase in the radical/ion flux on the substrate.

Particulate waste outflow from fish-farming cages. How much is uneaten feed?

Science.gov (United States)

Ballester-Moltó, M; Sanchez-Jerez, P; Cerezo-Valverde, J; Aguado-Giménez, F

2017-06-15

Particulate wastes drive benthic organic enrichment from cage fish farming. Differentiation between faeces and uneaten feed estimates at cage level are of great value to both economize the feeding process and reduce waste. This study estimates the particulate waste outflowing cages at different depths and orientations, and the wasted feed component by combining in situ measurements and modelling. Particulate matter flux (PMF) was greater vertically through the cage bottoms (60.89%), but lateral outflow was also substantial (39.11%). PMF occurs all around the cages, and the influence of the mainstream current was low. Wasted feed was greatly variable, reaching high values (about 50% of supplied feed. The self-application of feed wastage monitoring and estimates by fish farmers is recommended to improve sustainability. Copyright © 2017 Elsevier Ltd. All rights reserved.

Be a Cage-Buster

Science.gov (United States)

Hess, Frederick M.

2013-01-01

"A cage-buster can't settle for ambiguity, banalities, or imprecision," writes well-known educator and author Rick Hess. "These things provide dark corners where all manners of ineptitude and excuse-making can hide." Hess suggests that leaders need to clearly define the problems they're trying to solve and open…

Polyetheretherketone (PEEK) cages in cervical applications: a systematic review.

Science.gov (United States)

Kersten, Roel Frederik Mark Raymond; van Gaalen, Steven M; de Gast, Arthur; Öner, F Cumhur

2015-06-01

Polyetheretherketone (PEEK) cages have been widely used during the past decade in patients with degenerative disorders of the cervical spine. Their radiolucency and low elastic modulus make them attractive attributes for spinal fusion compared with titanium and bone graft. Still, limitations are seen such as pseudoarthrosis, subsidence, and migration of the cages. Limited evidence on the clinical outcome of PEEK cages is found in the literature other than noncomparative cohort studies with only a few randomized controlled trials. To assess the clinical and radiographic outcome of PEEK cages in the treatment of degenerative disc disorders and/or spondylolisthesis in the cervical spine. Systematic review of all randomized controlled trials and prospective and retrospective nonrandomized comparative studies with a minimum follow-up of 6 months and all noncomparative cohort studies with a long-term follow-up of more than 5 years. The primary outcome variable was clinical performance. Secondary outcome variables consisted of radiographic scores. The MEDLINE, EMBASE, and Cochrane Library databases were searched according to the Preferred Reporting Items of Systematic reviews and Meta-Analyses statement and Meta-analysis Of Observational Studies in Epidemiology guidelines. No conflict of interest reported. No funding received. A total of 223 studies were identified, of which 10 studies were included. These comprised two randomized controlled trials, five prospective comparative trials, and three retrospective comparative trials. Minimal evidence for better clinical and radiographic outcome is found for PEEK cages compared with bone grafts in the cervical spine. No differences were found between PEEK, titanium, and carbon fiber cages. Future studies are needed to improve methodology to minimize bias. Publication of lumbar interbody fusion studies needs to be promoted because differences in clinical and/or radiographic scores are more likely to be demonstrated in this part

A stochastic frontier analysis of technical efficiency of fish cage culture in Peninsular Malaysia.

Science.gov (United States)

Islam, Gazi Md Nurul; Tai, Shzee Yew; Kusairi, Mohd Noh

2016-01-01

Cage culture plays an important role in achieving higher output and generating more export earnings in Malaysia. However, the cost of fingerlings, feed and labour have increased substantially for cage culture in the coastal areas in Peninsular Malaysia. This paper uses farm level data gathered from Manjung, Perak and Kota Tinggi, Johor to investigate the technical efficiency of brackish water fish cage culture using the stochastic frontier approach. The technical efficiency was estimated and specifically the factors affecting technical inefficiencies of fish cage culture system in Malaysia was investigated. On average, 37 percent of the sampled fish cage farms are technically efficient. The results suggest very high degrees of technical inefficiency exist among the cage culturists. This implies that great potential exists to increase fish production through improved efficiency in cage culture management in Peninsular Malaysia. The results indicate that farmers obtained grouper fingerlings from other neighboring countries due to scarcity of fingerlings from wild sources. The cost of feeding for grouper (Epinephelus fuscoguttatus) requires relatively higher costs compared to seabass (Lates calcarifer) production in cage farms in the study areas. Initiatives to undertake extension programmes at the farm level are needed to help cage culturists in utilizing their resources more efficiently in order to substantially enhance their fish production.

Teaching in the Institutional Cage: Metaphor and Collateral Oppression

Science.gov (United States)

Noël Smith, Becky L.

2014-01-01

This analysis is a philosophical exploration of Marilyn Frye's metaphor of the cage and Patricia Hill Collins' theory of intersecting oppressions. It argues that social structures and forms of oppressive knowledge make up the individual wires on each person's cage and that these work to confine individuals, particularly those in the…

Specific Internalisation of Gold Nanoparticles into Engineered Porous Protein Cages via Affinity Binding.

Science.gov (United States)

Paramelle, David; Peng, Tao; Free, Paul; Fernig, David G; Lim, Sierin; Tomczak, Nikodem

2016-01-01

Porous protein cages are supramolecular protein self-assemblies presenting pores that allow the access of surrounding molecules and ions into their core in order to store and transport them in biological environments. Protein cages' pores are attractive channels for the internalisation of inorganic nanoparticles and an alternative for the preparation of hybrid bioinspired nanoparticles. However, strategies based on nanoparticle transport through the pores are largely unexplored, due to the difficulty of tailoring nanoparticles that have diameters commensurate with the pores size and simultaneously displaying specific affinity to the cages' core and low non-specific binding to the cages' outer surface. We evaluated the specific internalisation of single small gold nanoparticles, 3.9 nm in diameter, into porous protein cages via affinity binding. The E2 protein cage derived from the Geobacillus stearothermophilus presents 12 pores, 6 nm in diameter, and an empty core of 13 nm in diameter. We engineered the E2 protein by site-directed mutagenesis with oligohistidine sequences exposing them into the cage's core. Dynamic light scattering and electron microscopy analysis show that the structures of E2 protein cages mutated with bis- or penta-histidine sequences are well conserved. The surface of the gold nanoparticles was passivated with a self-assembled monolayer made of a mixture of short peptidols and thiolated alkane ethylene glycol ligands. Such monolayers are found to provide thin coatings preventing non-specific binding to proteins. Further functionalisation of the peptide coated gold nanoparticles with Ni2+ nitrilotriacetic moieties enabled the specific binding to oligohistidine tagged cages. The internalisation via affinity binding was evaluated by electron microscopy analysis. From the various mutations tested, only the penta-histidine mutated E2 protein cage showed repeatable and stable internalisation. The present work overcomes the limitations of currently

Bisphenol A is released from used polycarbonate animal cages into water at room temperature

Science.gov (United States)

Howdeshell, Kembra L.; Peterman, Paul H.; Judy, Barbara M.; Taylor, Julia A.; Orazio, Carl E.; Ruhlen, Rachel L.; vom Saal, Frederick S.; Welshons, Wade V.

2003-01-01

Bisphenol A (BPA) is a monomer with estrogenic activity that is used in the production of food packaging, dental sealants, polycarbonate plastic, and many other products. The monomer has previously been reported to hydrolyze and leach from these products under high heat and alkaline conditions, and the amount of leaching increases as a function of use. We examined whether new and used polycarbonate animal cages passively release bioactive levels of BPA into water at room temperature and neutral pH. Purified water was incubated at room temperature in new polycarbonate and polysulfone cages and used (discolored) polycarbonate cages, as well as control (glass and used polypropylene) containers. The resulting water samples were characterized with gas chromatography/mass spectrometry (GC/MS) and tested for estrogenic activity using an MCF-7 human breast cancer cell proliferation assay. Significant estrogenic activity, identifiable as BPA by GC/MS (up to 310 micro g/L), was released from used polycarbonate animal cages. Detectable levels of BPA were released from new polycarbonate cages (up to 0.3 micro g/L) as well as new polysulfone cages (1.5 micro g/L), whereas no BPA was detected in water incubated in glass and used polypropylene cages. Finally, BPA exposure as a result of being housed in used polycarbonate cages produced a 16% increase in uterine weight in prepubertal female mice relative to females housed in used polypropylene cages, although the difference was not statistically significant. Our findings suggest that laboratory animals maintained in polycarbonate and polysulfone cages are exposed to BPA via leaching, with exposure reaching the highest levels in old cages.

Effects of separation of resources on behaviour, physical condition and production of laying hens in furnished cages.

Science.gov (United States)

Shimmura, T; Azuma, T; Eguchi, Y; Uetake, K; Tanaka, T

2009-01-01

1. Based on our previous studies, we designed a medium-sized furnished cage with a dust bath and nest box on both sides of the cage (MFS) and evaluated its usefulness. 2. We used 180 White Leghorn layers. At the age of 17 weeks, the birds were distributed at random into one of the 4 cage designs: conventional cages (CC; 6 cages and 5 hens per cage), small (SF; 6 cages and 5 hens per cage) and medium furnished cages (MFL; 6 cages and 10 hens per cage) with a 'localised' dust bath and nest box on one side of the cage, and MFS (6 cages and 10 hens per cage). The total allocation of resources per bird was similar for all furnished cage designs. Behaviour, physical condition and production were measured in each cage. 3. Moving was more frequent in MFS and MFL than in CC and SF. The proportion of hens performing aggressive pecking and severe feather pecking was higher in MFL than CC and SF. These aggressive interactions occurred frequently in the dust bath area in MFL; however, these tendencies were not found in MFS. Egg production and egg mass were lower in MFL than in SF, while the production in MFS was similar to those in CC and SF. MFS hens laid eggs on the cage floor more often than in MFL. 4. In conclusion, these results demonstrate the possible usefulness of MFS. However, some inconsistent results and ways of improving MFS design were also identified.

Modelling of fluid-solid interaction using two stand-alone codes

CSIR Research Space (South Africa)

Grobler, Jan H

2010-01-01

Full Text Available A method is proposed for the modelling of fluid-solid interaction in applications where fluid forces dominate. Data are transferred between two stand-alone codes: a dedicated computational fluid dynamics (CFD) code capable of free surface modelling...

Comparative architecture of octahedral protein cages. I. Indexed enclosing forms

Science.gov (United States)

Janner, A.

2008-07-01

The architecture of four protein cages (bacterio ferritin, human mitochondrial ferritin, sulfur oxygenase reductase and small heat-shock protein) are compared top-to-bottom, starting from polyhedra with vertices at cubic lattice points enclosing the cage down to indexed polyhedral forms of single monomers.

Dynamic modeling of an asynchronous squirrel-cage machine; Modelisation dynamique d'une machine asynchrone a cage

Energy Technology Data Exchange (ETDEWEB)

Guerette, D.

2009-07-01

This document presented a detailed mathematical explanation and validation of the steps leading to the development of an asynchronous squirrel-cage machine. The MatLab/Simulink software was used to model a wind turbine at variable high speeds. The asynchronous squirrel-cage machine is an electromechanical system coupled to a magnetic circuit. The resulting electromagnetic circuit can be represented as a set of resistances, leakage inductances and mutual inductances. Different models were used for a comparison study, including the Munteanu, Boldea, Wind Turbine Blockset, and SimPowerSystem. MatLab/Simulink modeling results were in good agreement with the results from other comparable models. Simulation results were in good agreement with analytical calculations. 6 refs, 2 tabs, 9 figs.

PyMICE: APython library for analysis of IntelliCage data.

Science.gov (United States)

Dzik, Jakub M; Puścian, Alicja; Mijakowska, Zofia; Radwanska, Kasia; Łęski, Szymon

2018-04-01

IntelliCage is an automated system for recording the behavior of a group of mice housed together. It produces rich, detailed behavioral data calling for new methods and software for their analysis. Here we present PyMICE, a free and open-source library for analysis of IntelliCage data in the Python programming language. We describe the design and demonstrate the use of the library through a series of examples. PyMICE provides easy and intuitive access to IntelliCage data, and thus facilitates the possibility of using numerous other Python scientific libraries to form a complete data analysis workflow.

Analysis and controller design for stand-alone VSIs in synchronous reference frame

DEFF Research Database (Denmark)

Ramezani, Malek; Li, Shuhui; Golestan, Saeed

2017-01-01

-by-step graphical analysis and design approach for a three-phase stand-alone VSI system in the dq reference frame, which provides a clear systematic decoupling process to design the inner- and outer-loop current and voltage controllers, respectively. The closed-loop d- and q-axis output impedances of the stand......-alone VSI system by considering the coupling effects between axes are also formulated, modelled, and evaluated. The study investigates how the decoupling and compensating terms added in the current and voltage controllers affect the dynamic performance and output dq impedances of the VSI system. Simulation...... and hardware results verify the effectiveness of the graphic design and analysis strategy....

Environmental/Climatic Effect on Stand-Alone Solar Energy Supply ...

African Journals Online (AJOL)

This paper investigates the climatic eects and environmental variations on the performance of a stand-alone photovoltaic system. The eects of partial shading with dierent climate conditions and load resistance variations were examined. A survey of some of the work done in this eld of environmental eect on solar panel was ...

Caged Molecular Glues as Photoactivatable Tags for Nuclear Translocation of Guests in Living Cells.

Science.gov (United States)

Arisaka, Akio; Mogaki, Rina; Okuro, Kou; Aida, Takuzo

2018-02-21

We developed dendritic caged molecular glues ( Caged Glue-R) as tags for nucleus-targeted drug delivery, whose multiple guanidinium ion (Gu + ) pendants are protected by an anionic photocleavable unit (butyrate-substituted nitroveratryloxycarbonyl; BA NVOC). Negatively charged Caged Glue-R hardly binds to anionic biomolecules because of their electrostatic repulsion. However, upon exposure of Caged Glue-R to UV light or near-infrared (NIR) light, the BA NVOC groups of Caged Glue-R are rapidly detached to yield an uncaged molecular glue ( Uncaged Glue-R) that carries multiple Gu + pendants. Because Gu + forms a salt bridge with PO 4 - , Uncaged Glue-R tightly adheres to anionic biomolecules such as DNA and phospholipids in cell membranes by a multivalent salt-bridge formation. When tagged with Caged Glue-R, guests can be taken up into living cells via endocytosis and hide in endosomes. However, when the Caged Glue-R tag is photochemically uncaged to form Uncaged Glue-R, the guests escape from the endosome and migrate into the cytoplasm followed by the cell nucleus. We demonstrated that quantum dots (QDs) tagged with Caged Glue-R can be delivered efficiently to cell nuclei eventually by irradiation with light.

A laboratory cage for foster nursing newborn mice

Directory of Open Access Journals (Sweden)

S. Marques-de-Araújo

1999-03-01

Full Text Available We describe a cage to be used for foster nursing in order to guarantee that original mother's colostrum is not ingested by the newborn mice. A common (30.5 cm x 19.5 cm x 12.0 cm mouse cage was fitted with a wire net tray with a mesh (1 cm x 1 cm, which divides the cage into an upper and a lower compartment. Mice born to females placed in the upper compartment pass through the mesh and fall into the lower compartment, where another lactating female with one or two of its own pups are. Of a total of 28 newborn mice of C3H/He and Swiss strains, 23 were successfully fostered. Important observations are presented to show that this is a valuable alternative for foster studies without great suffering on the part of the female.

Evaluation of cage micro-environment of mice housed on various types of bedding materials.

Science.gov (United States)

Smith, Ellen; Stockwell, Jason D; Schweitzer, Isabelle; Langley, Stephen H; Smith, Abigail L

2004-07-01

A variety of environmental factors can affect the outcomes of studies using laboratory rodents. One such factor is bedding. Several new bedding materials and processing methods have been introduced to the market in recent years, but there are few reports of their performance. In the studies reported here, we have assessed the cage micro-environment (in-cage ammonia levels, temperature, and humidity) of mice housed on various kinds of bedding and their combinations. We also compared results for bedding supplied as Nestpaks versus loose bedding. We studied C57BL/6J mice (commonly used) and NOD/LtJ mice (heavy soilers) that were maintained, except in one study, in static duplex cages. In general, we observed little effect of bedding type on in-cage temperature or humidity; however, there was considerable variation in ammonia concentrations. The lowest ammonia concentrations occurred in cages housing mice on hardwood bedding or a mixture of corncob and alpha cellulose. In one experiment comparing the micro-environments of NOD/LtJ male mice housed on woodpulp fiber bedding in static versus ventilated caging, we showed a statistically significant decrease in ammonia concentrations in ventilated cages. Therefore, our data show that bedding type affects the micro-environment in static cages and that effects may differ for ventilated cages, which are being used in vivaria with increasing frequency. Copyright 2004 American Association for Laboratory Animal Science

Effect of acclimation to caging on nephrotoxic response of rats to uranium.

Science.gov (United States)

Damon, E G; Eidson, A F; Hobbs, C H; Hahn, F F

1986-02-01

Animal studies of the toxicity and metabolism of radionuclides and chemicals often require housing of rats in metabolism cages for excreta collection. Response of rats to toxic substances may be affected by environmental factors such as the type of cage used. Dose-response studies were conducted to assess the effects of two types of cages on the nephrotoxic response of rats to uranium from implanted refined uranium ore (yellowcake). The LD50/21 days was 6 mg of uranium ore per kilogram body weight (6 mg U/kg). The 95% confidence limit (C.L.) was 3-8 mg U/kg for rats housed in metabolism cages beginning on the day of implantation (naive rats). However, for rats housed in metabolism cages for 21 days before implantation (acclimated rats) the LD50/21 days was 360 mg U/kg (95% C.L. = 220-650 mg U/kg), which was the same value obtained for rats housed continuously in polycarbonate cages. This significant difference (P less than 0.01) in response of naive rats compared to response of acclimated rats appeared related to a significantly lower water consumption by the naive rats.

Optical cage generated by azimuthal- and radial-variant vector beams.

Science.gov (United States)

Man, Zhongsheng; Bai, Zhidong; Li, Jinjian; Zhang, Shuoshuo; Li, Xiaoyu; Zhang, Yuquan; Ge, Xiaolu; Fu, Shenggui

2018-05-01

We propose a method to generate an optical cage using azimuthal- and radial-variant vector beams in a high numerical aperture optical system. A new kind of vector beam that has azimuthal- and radial-variant polarization states is proposed and demonstrated theoretically. Then, an integrated analytical model to calculate the electromagnetic field and Poynting vector distributions of the input azimuthal- and radial-variant vector beams is derived and built based on the vector diffraction theory of Richards and Wolf. From calculations, a full polarization-controlled optical cage is obtained by simply tailoring the radial index of the polarization, the uniformity U of which is up to 0.7748, and the cleanness C is zero. Additionally, a perfect optical cage can be achieved with U=1, and C=0 by introducing an amplitude modulation; its magnetic field and energy flow are also demonstrated in detail. Such optical cages may be helpful in applications such as optical trapping and high-resolution imaging.

Stand-alone wind system with Vanadium Redox Battery energy storage

DEFF Research Database (Denmark)

Teodorescu, Remus; Barote, L.; Weissbach, R.

2008-01-01

Energy storage devices are required for power balance and power quality in stand alone wind energy systems. A Vanadium Redox Flow Battery (VRB) system has many features which make its integration with a stand-alone wind energy system attractive. This paper proposes the integration of a VRB system...... with a typical stand-alone wind energy system during wind speed variation as well as transient performance under variable load. The investigated system consists of a variable speed wind turbine with permanent magnet synchronous generator (PMSG), diode rectifier bridge, buck-boost converter, bidirectional charge...... controller, transformer, inverter, ac loads and VRB (to store a surplus of wind energy and to supply power during a wind power shortage). The main purpose is to supply domestic appliances through a single phase 230V, 50Hz inverter. Simulations are accomplished in order to validate the stability of the supply....

Depopulation of Caged Layer Hens with a Compressed Air Foam System

Science.gov (United States)

Gurung, Shailesh; Hoffman, John; Stringfellow, Kendre; Abi-Ghanem, Daad; Zhao, Dan; Caldwell, David; Lee, Jason; Styles, Darrel; Berghman, Luc; Byrd, James; Farnell, Yuhua; Archer, Gregory

2018-01-01

Simple Summary Reportable diseases, such as avian influenza, spread rapidly among poultry, resulting in the death of a large number of birds. Once such a disease has been diagnosed at a farm, infected and susceptible birds are rapidly killed to prevent the spread of the disease. The methods to eliminate infected caged laying hens are limited. An experiment was conducted to study the effectiveness of foam made from compressed air, water, and soap to kill laying hens in cages. The study found that stress levels of the hens killed using compressed air foam in cages to be similar to the hens killed by carbon dioxide or the negative control. Hens exposed to carbon dioxide died earlier as compared to the foam methods. The authors conclude that application of compressed air foam in cages is an alternative to methods such as gas inhalation and ventilation shutdown to rapidly and humanely kill laying hens during epidemics. Abstract During the 2014–2015 US highly pathogenic avian influenza (HPAI) outbreak, 50.4 million commercial layers and turkeys were affected, resulting in economic losses of $3.3 billion. Rapid depopulation of infected poultry is vital to contain and eradicate reportable diseases like HPAI. The hypothesis of the experiment was that a compressed air foam (CAF) system may be used as an alternative to carbon dioxide (CO2) inhalation for depopulating caged layer hens. The objective of this study was to evaluate corticosterone (CORT) and time to cessation of movement (COM) of hens subjected to CAF, CO2 inhalation, and negative control (NEG) treatments. In Experiment 1, two independent trials were conducted using young and spent hens. Experiment 1 consisted of five treatments: NEG, CO2 added to a chamber, a CO2 pre-charged chamber, CAF in cages, and CAF in a chamber. In Experiment 2, only spent hens were randomly assigned to three treatments: CAF in cages, CO2 added to a chamber, and aspirated foam. Serum CORT levels of young hens were not significantly

(reprocessed)CAGE peaks - FANTOM5 | LSDB Archive [Life Science Database Archive metadata

Lifescience Database Archive (English)

Full Text Available switchLanguage; BLAST Search Image Search Home About Archive Update History Data List Contact us FANTOM...g38/mm10). Data file File name: (reprocessed)CAGE_peaks (Homo sapiens) File URL: ftp://ftp.biosciencedbc.jp/archive/fantom...)CAGE_peaks (Mus musculus) File URL: ftp://ftp.biosciencedbc.jp/archive/fantom5/d...his Database Site Policy | Contact Us (reprocessed)CAGE peaks - FANTOM5 | LSDB Archive ...

Analysis and interpretation of the model of a Faraday cage for electromagnetic compatibility testing

Directory of Open Access Journals (Sweden)

Nenad V. Munić

2014-02-01

Full Text Available In order to improve the work of the Laboratory for Electromagnetic Compatibility Testing in the Technical Test Center (TTC, we investigated the influence of the Faraday cage on measurement results. The primary goal of this study is the simulation of the fields in the cage, especially around resonant frequencies, in order to be able to predict results of measurements of devices under test in the anechoic chamber or in any other environment. We developed simulation (computer models of the cage step by step, by using the Wipl-D program and by comparing the numerical results with measurements as well as by resolving difficulties due to the complex structure and imperfections of the cage. The subject of this paper is to present these simulation models and the corresponding results of the computations and measurements. Construction of the cage The cage is made of steel plates with the dimensions 1.25 m x 2.5 m. The base of the cage is a square; the footprint interior dimensions are 3.76 m x 3.76 m, and the height is 2.5 m. The cage ceiling is lowered by plasticized aluminum strips. The strips are loosely attached to the carriers which are screwed to the ceiling. The cage has four ventilation openings (two on the ceiling and two on one wall, made of honeycomb waveguide holes. In one corner of the cage, there is a single door with springs made of beryllium bronze. For frequencies of a few tens of MHz, the skin effect is fully developed in the cage walls. By measuring the input impedance of the wire line parallel to a wall of the cage, we calculated the surface losses of the cage plates. In addition, we used a magnetic probe to detect shield discontinuities. We generated a strong current at a frequency of 106 kHz outside the cage and measured the magnetic field inside the cage at the places of cage shield discontinuities. In this paper, we showed the influence of these places on the measurement results, especially on the qualitative and quantitative

Mooring Design Selection of Aquaculture Cage for Indonesian Ocean

Science.gov (United States)

Mulyadi, Y.; Syahroni, N.; Sambodho, K.; Zikra, M.; Wahyudi; Adia, H. B. P.

2018-03-01

Fish production is important for the economy in fishing community and for ensuring food security. Climate change will lead a threat to fish productivity. Therefore, a solution offered is to cultivate certain fish, especially those with high economic value by using offshore aquaculture technology. A Sea Station cage is one of the offshore aquaculture cage model that has been used in some locations. As a floating structure, the Sea Station cage need a mooring system to maintain its position. This paper presents the selection analysis of the mooring system designs of the Sea Station cage model that it is suitable with Indonesia Ocean. There are 3 mooring configurations that are linear array, rectangular array, and 4 points mooring type. The nylon mooring rope type has been selected to be used on the 3 mooring configurations and the rope has a diameter of 104 mm with a breaking force of 2.3 MN. Based on results from comparing the 3 mooring configurations, the best mooring configuration is linear array with the tension on the rope of 217 KN and has the safety factor of 0.2 based on DNVGL OS-E301

Caged molecular beacons: controlling nucleic acid hybridization with light.

Science.gov (United States)

Wang, Chunming; Zhu, Zhi; Song, Yanling; Lin, Hui; Yang, Chaoyong James; Tan, Weihong

2011-05-28

We have constructed a novel class of light-activatable caged molecular beacons (cMBs) that are caged by locking two stems with a photo-labile biomolecular interaction or covalent bond. With the cMBs, the nucleic acid hybridization process can be easily controlled with light, which offers the possibility for a high spatiotemporal resolution study of intracellular mRNAs. © The Royal Society of Chemistry 2011

Availability model of stand-alone photovoltaic system

Science.gov (United States)

Mazurek, G.

2017-08-01

In this paper we present a simple, empirical model of stand-alone photovoltaic power system availability. The model is a final result of five-year long studies and ground measurements of solar irradiation carried out in Central Europe. The obtained results facilitate sizing of PV modules that have to be installed with taking into account system's availability level in each month of a year. The model can be extended to different geographical locations, with help of local meteorological data or solar irradiation datasets derived from satellite measurements.

Does Lordotic Angle of Cage Determine Lumbar Lordosis in Lumbar Interbody Fusion?

Science.gov (United States)

Hong, Taek-Ho; Cho, Kyu-Jung; Kim, Young-Tae; Park, Jae-Woo; Seo, Beom-Ho; Kim, Nak-Chul

2017-07-01

Retrospective, radiological analysis. To determine that 15° lordotic angle cages create higher lumbar lordosis in open transforaminal lumbar interbody fusion (TLIF) than 4° and 8° cages. Restoration of lumbar lordosis is important to obtain good outcome after lumbar fusion surgery. Various shapes and angles of cages in interbody fusion have been used; however, it is not proved that lordotic angle of cages determine lumbar lordosis. Sixty-seven patients were evaluated after TLIF using 15° cages and screw instrumentation. For comparison, TLIF using 4° lordotic angle cages in 65 patients and 8° cages in 49 patients were analyzed. Lumbar lordosis angles, segmental lordosis angles, disc height, and bony union rate were measured on the radiographs. The lumbar lordosis was 31.1° preoperatively, improved to 42.9° postoperatively, and decreased to 36.4° at the last follow-up in the 15° group. It was 35.8° before surgery, corrected to 41.5° after surgery, and changed to 33.6° at the last follow-up in the 4° group. In the 8° group, it was 32.7° preoperatively, improved to 39.1° postoperatively, and decreased to 34.5° at the last follow-up. These changes showed statistical significances (P lordosis at L4-5 was 6.6° before surgery, 13.1° after surgery, and 9.8° at the last follow-up in the 15° group. It was 6.9°, 9.5°, and 6.2° in the 4° group and 6.7°, 9.8°, and 8.1° in the 8° group, respectively (P lordosis after TLIF. Cages with sufficient lordotic angle showed better restoration of lumbar lordosis and prevention of loss of correction. 4.

Hybrid Configuration of Darrieus and Savonius Rotors for Stand-alone Power Systems

Science.gov (United States)

Wakui, Tetsuya; Tanzawa, Yoshiaki; Hashizume, Takumi; Nagao, Toshio

The suitable hybrid configuration of Darrieus lift-type and Savonius drag-type rotors for stand-alone wind turbine-generator systems is discussed using our dynamic simulation model. Two types of hybrid configurations are taken up: Type-A installs the Savonius rotor inside the Darrieus rotor and Type-B installs the Savonius rotor outside the Darrieus rotor. The computed results of the output characteristics and the dynamic behaviors of the system operated at the maximum power coefficient points show that Type-A, which has fine operating behavior to wind speed changes and can be compactly designed because of a shorter rotational shaft, is an effective way for self-controlled stand-alone small-scale systems.

Environmental impact of sea bass cage farming in the north Adriatic Sea

Directory of Open Access Journals (Sweden)

Domenico Lanari

2010-01-01

Full Text Available The main objective of the research was to reduce the organic and nutrient load under the net pen fish farms. An exper- iment was conducted to study the effects of artificial barriers fixed under a set of sea cages in order to reduce the envi- ronmental impact. The artificial barriers were made of four submerged galvanized steel pipes coated with plastic and placed on the sea floor (10 m depth in the Trieste gulf. The experimental design was as follows: control (C, cages with barriers (B, cages without barriers (WB. Measurements were taken on the surface as well as at 4 and 8m of depth. The trial lasted from the end of June 2000 to December 2001. Water quality parameters were not significantly influenced by the fish cages. Surface samples were characterised by lower levels of salinity and higher levels of oxygen and nitrate compared to those taken at 4 and 8 m. The artificial barriers favoured the establishment of a rich epiphytic fauna that took advantage of the presence of organic matter derived from fish cages. The two species Nucula nucleusand Neanthes caudataand the total bacterial counts were identified as potential indicators of pollution under the fish cage farms.

Polymers containing borane or carborane cage compounds and related applications

Science.gov (United States)

Bowen, III, Daniel E.; Eastwood, Eric A [Raymore, MO

2012-06-05

Polymers comprising residues of borane and/or carborane cage compound monomers having at least one polyalkoxy silyl substituent. Such polymers can further comprise one or more reactive matrices and/or co-monomers covalently bound with the cage compound monomer residues. Methods of making and applications for using such polymers are also disclosed.

Biology's built-in Faraday cages

Science.gov (United States)

Klee, Maurice M.

2014-05-01

Biological fluids are water-based, ionic conductors. As such, they have both high relative dielectric constants and substantial conductivities, meaning they are lossy dielectrics. These fluids contain charged molecules (free charges), whose movements play roles in essentially all cellular processes from metabolism to communication with other cells. Using the problem of a point source in air above a biological fluid of semi-infinite extent, the bound charges in the fluid are shown to perform the function of a fast-acting Faraday cage, which protects the interior of the fluid from external electric fields. Free charges replace bound charges in accordance with the fluid's relaxation time, thereby providing a smooth transition between the initial protection provided by the bound charges and the steady state protection provided by the free charges. The electric fields within the biological fluid are thus small for all times just as they would be inside a classical Faraday cage.

Musica come divenire. Il paesaggio sonoro secondo John cage

Directory of Open Access Journals (Sweden)

Francesca Aste

2008-12-01

Full Text Available John Cage ha dedicato tutta la sua vita all’indagine delle possibilità di relazione dell’uomo con i suoni che lo circondano, allargando il campo dell’arte musicale a quello dell’etica e dell’ecologia. Cage non si è occupato di soundscape come un genere compositivo specifico, come forse oggi potremmo identificarlo, tuttavia l’ambiente occupa un ruolo centrale in relazione al suo modo di comporre.

Endohedral complexes of Polyhedral Oligomeric Silsesquioxane (POSS) cages with transition metal dihydrides

Energy Technology Data Exchange (ETDEWEB)

Wang, Xiqiao; Corn, John; Hagelberg, Frank, E-mail: hagelber@etsu.edu

2013-11-29

Highlights: • Comparative studies of POSS cages with endohedral metal dihydrides. • Exothermic inclusion was found for the T{sub 10} cage with MH{sub 2}, M = Ti, Ru, Os, Pt. • Within this group of metal atoms, the only exothermic MH{sub 4}@T{sub m} unit is that with M = Os. • Enhanced hydrogen atom density, as compared to free MH{sub 4}, was found in the cage. • No exothermic solutions were identified for MH{sub 6}@T{sub 10}. - Abstract: Polyhedral Oligomeric Silsesquioxane (POSS) cages are investigated in terms of their potential to enclose small metal hydrides, with the objective of defining conditions that maximize the number of encapsulated hydrogen atoms. Systems of the form MH{sub 2n}@T{sub m}, where n = 1–3, m = 8, 10, and M comprises metal atom species of the groups IV, VI, VIII, X, and XII, are studied by methods of ab initio and density functional theory (DFT). The resulting composites are categorized with respect to their structural and energetic features. For MH{sub 2}@T{sub 8}, it is found in all cases considered that including MH{sub 2} into the POSS cage is an endothermic process. For MH{sub 2}@T{sub 10} and M = Ti, Ru, Os, Pt, inclusion of the MH{sub 2} guest into the cage turns out to be exothermic, and also leaves the cage intact. For MH{sub 4}@T{sub m}, this behavior is only observed for one system, OsH{sub 4}@T{sub 10}.

Determining basic parameters of shafts with cage hoisting systems in mines with steep seams

Energy Technology Data Exchange (ETDEWEB)

Durov, E.M.

1982-05-01

This paper analyzes problems associated with increasing depth of mine shafts in operating coal mines. Schemes of shaft excavation in mines with steep coal seams are analyzed. Removal of mine rock and the ground surface by existing mine shafts is most economical in most cases. Yuzhgiproshakht has investigated a number of hoisting schemes during mine shaft excavation in order to select the optimum shaft diameter which permits shaft reconstruction and deepening to be optimized. The following conditions are analyzed: coal output of a coal mine ranges from 0.9 megatons (Mt) to 1.8 Mt/year, mining depth ranges from 600 m to 1600 m (with intermediary depth of 800, 1000, 1200 and 1400 m also considered). Separate hoisting of coal and rock waste is used. Shaft sinking rate ranges from 10 to 50 m/month. The following hoisting schemes are analyzed: two independent systems which consist of a cage with counterweight, three systems of a cage with counterweight, double cage system and a cage with counterweight. Hoisting schemes are shown in 9 diagrams. Investigations show that a 7 to 8 m diameter of mine shafts is most economic. In mine shafts 7 m in diameter equipped with two cages with counterweights one of the cages is removed to form a free space for the hoisting bucket. In the 8 m shaft equipped with a double cage system and a cage with counterweight the cage with counterweight is removed to form a free place for the hoisting bucket used during shaft excavation.

Research on vibration properties of auxiliary bearing cage used in HTR-10 GT project

International Nuclear Information System (INIS)

Qin Qingquan; Yang Guojun; Shi Zhengang; Yu Suyuan

2009-01-01

Auxiliary Bearings (ABs) is one of the most important parts in Active Magnetic Bearing (AMB) system, which was used in HTR-10 GT project. This paper uses finite element method to analyze the centrifugal stress and free vibration properties of the cage according to its work condition. And different geometric parameters of the cage that has effects on its vibration performance are discussed. The results show that the highest centrifugal stress is in the middle of the cage side sill. The low odder vibration modes of the cage can be induced when the auxiliary bearings are working. Proper geometric parameters and ball pocket number can enhance the performance of the cage. (authors)

Social communication in mice--are there optimal cage conditions?

Directory of Open Access Journals (Sweden)

Allain-Thibeault Ferhat

Full Text Available Social communication is heavily affected in patients with neuropsychiatric disorders. Accordingly, mouse models designed to study the mechanisms leading to these disorders are tested for this phenotypic trait. Test conditions vary between different models, and the effect of these test conditions on the quantity and quality of social interactions and ultrasonic communication is unknown. The present study examines to which extent the habituation time to the test cage as well as the shape/size of the cage influence social communication in freely interacting mice. We tested 8 pairs of male mice in free dyadic social interactions, with two habituation times (20 min and 30 min and three cage formats (rectangle, round, square. We tested the effect of these conditions on the different types of social contacts, approach-escape sequences, follow behavior, and the time each animal spent in the vision field of the other one, as well as on the emission of ultrasonic vocalizations and their contexts of emission. We provide for the first time an integrated analysis of the social interaction behavior and ultrasonic vocalizations. Surprisingly, we did not highlight any significant effect of habituation time and cage shape/size on the behavioral events examined. There was only a slight increase of social interactions with the longer habituation time in the round cage. Remarkably, we also showed that vocalizations were emitted during specific behavioral sequences especially during close contact or approach behaviors. The present study provides a protocol reliably eliciting social contacts and ultrasonic vocalizations in adult male mice. This protocol is therefore well adapted for standardized investigation of social interactions in mouse models of neuropsychiatric disorders.

The effect of space allowance and cage size on laying hens housed in furnished cages, Part II: Behavior at the feeder

Science.gov (United States)

Widowski, T. M; Caston, L. J; Casey-Trott, T. M; Hunniford, M. E

2017-01-01

Abstract Standards for feeder (a.k.a. feed trough) space allowance (SA) are based primarily on studies in conventional cages where laying hens tend to eat simultaneously, limiting feeder space. Large furnished cages (FC) offer more total space and opportunities to perform a greater variety of behaviors, which may affect feeding behavior and feeder space requirements. Our objective was to determine the effects of floor/feeder SA on behavior at the feeder. LSL-Lite hens were housed in FC equipped with a nest, perches, and a scratch mat. Hens with SA of either 520 cm2 (Low; 8.9 cm feeder space/hen) or 748 cm2 (High; 12.8 cm feeder space/hen) per bird resulted in groups of 40 vs. 28 birds in small FC (SFC) and 80 vs. 55 in large FC (LFC). Chain feeders ran at 0500, 0800, 1100, 1400, and 1700 with lights on at 0500 and off at 1900 hours. Digital recordings of FC were scanned at chain feeder onset and every 15 min for one h after (5 scans × 5 feeding times × 2 d) to count the number of birds with their head in the feeder. All occurrences of aggressive pecks and displacements during 2 continuous 30-minute observations at 0800 h and 1700 h also were counted. Mixed model repeated analyses tested the effects of SA, cage size, and time on the percent of hens feeding, and the frequency of aggressive pecks and displacements. Surprisingly, the percent of birds feeding simultaneously was similar regardless of cage size (LFC: 23.0 ± 0.9%; SFC: 24.0 ± 1.0%; P = 0.44) or SA (Low: 23.8 ± 0.9%; High: 23.3 ± 1.0%; P = 0.62). More birds were observed feeding at 1700 h (35.3 ± 0.1%) than any at other time (P < 0.001). Feeder use differed by cage area (nest, middle, or scratch) over the d (P < 0.001). The frequency of aggressive pecks was low overall and not affected by SA or cage size. Frequency of displacements was also low but greater at Low SA (P = 0.001). There was little evidence of feeder competition at the Low SA in this study. PMID:29050409

Depopulation of Caged Layer Hens with a Compressed Air Foam System.

Science.gov (United States)

Gurung, Shailesh; Hoffman, John; Stringfellow, Kendre; Abi-Ghanem, Daad; Zhao, Dan; Caldwell, David; Lee, Jason; Styles, Darrel; Berghman, Luc; Byrd, James; Farnell, Yuhua; Archer, Gregory; Farnell, Morgan

2018-01-11

During the 2014-2015 US highly pathogenic avian influenza (HPAI) outbreak, 50.4 million commercial layers and turkeys were affected, resulting in economic losses of $3.3 billion. Rapid depopulation of infected poultry is vital to contain and eradicate reportable diseases like HPAI. The hypothesis of the experiment was that a compressed air foam (CAF) system may be used as an alternative to carbon dioxide (CO₂) inhalation for depopulating caged layer hens. The objective of this study was to evaluate corticosterone (CORT) and time to cessation of movement (COM) of hens subjected to CAF, CO₂ inhalation, and negative control (NEG) treatments. In Experiment 1, two independent trials were conducted using young and spent hens. Experiment 1 consisted of five treatments: NEG, CO₂ added to a chamber, a CO₂ pre-charged chamber, CAF in cages, and CAF in a chamber. In Experiment 2, only spent hens were randomly assigned to three treatments: CAF in cages, CO₂ added to a chamber, and aspirated foam. Serum CORT levels of young hens were not significantly different among the CAF in cages, CAF in a chamber, NEG control, and CO₂ inhalation treatments. However, spent hens subjected to the CAF in a chamber had significantly higher CORT levels than birds in the rest of the treatments. Times to COM of spent hens subjected to CAF in cages and aspirated foam were significantly greater than of birds exposed to the CO₂ in a chamber treatment. These data suggest that applying CAF in cages is a viable alternative for layer hen depopulation during a reportable disease outbreak.

Preliminary experience of titanium mesh cages for pathological fracture of middle and lower cervical vertebrae.

Science.gov (United States)

Chuang, Hao-Che; Wei, Sung-Tai; Lee, Han-Chung; Chen, Chun-Chung; Lee, Wen-Yuen; Cho, Der-Yang

2008-11-01

The advantages and disadvantages of titanium mesh cages (TMCs) assisted by anterior cervical plates (ACPs) for interbody fusion following cervical corpectomy were investigated. Between January 2002 and September 2006, 17 patients with cervical radiculomyelopathy caused by metastasis-induced pathologic fractures were selected for anterior corpectomy. TMCs were inserted into the post-corpectomy defect and stabilized by placement of ACPs filled with Triosite. Post-operative plain X-ray films indicated maintenance of spinal stability. No ceramic, donor site or surgery-related complications were observed. True trabeculation was observed in axial and reconstructive CT scans in all surviving patients one year after surgery. Neurological recovery, pain control, and good quality of life were achieved. Short hospital stays, minimal blood loss, short operation times and brief periods of bed confinement were also observed. We conclude that a TMC assisted by an ACP is safe and effective for interbody fusion following cervical corpectomy for pathological fractures resulting from cervical vertebral metastases.

Numerical study on the hydrodynamic characteristics of biofouled full-scale net cage

Science.gov (United States)

Bi, Chun-wei; Zhao, Yun-peng; Dong, Guo-hai

2015-06-01

The effect of biofouling on the hydrodynamic characteristics of the net cage is of particular interest as biofouled nettings can significantly reduce flow of well-oxygenated water reaching the stocked fish. For computational efficiency, the porous-media fluid model is proposed to simulate flow through the biofouled plane net and full-scale net cage. The porous coefficients of the porous-media fluid model can be determined from the quadratic-function relationship between the hydrodynamic forces on a plane net and the flow velocity using the least squares method. In this study, drag forces on and flow fields around five plane nets with different levels of biofouling are calculated by use of the proposed model. The numerical results are compared with the experimental data of Swift et al. (2006) and the effectiveness of the numerical model is presented. On that basis, flow through full-scale net cages with the same level of biofouling as the tested plane nets are modeled. The flow fields inside and around biofouled net cages are analyzed and the drag force acting on a net cage is estimated by a control volume analysis method. According to the numerical results, empirical formulas of reduction in flow velocity and load on a net cage are derived as function of drag coefficient of the corresponding biofouled netting.

Transcription regulatory networks analysis using CAGE

KAUST Repository

Tegné r, Jesper N.; Bjö rkegren, Johan L M; Ravasi, Timothy; Bajic, Vladimir

2009-01-01

and the fine interplay between regulatory proteins and the promoter structure governing the combinatorial regulation of gene expression. In this chapter we review how the CAGE data can be integrated with other measurements such as expression, physical

Plastic cages to protect Douglas-fir seedlings from animal damage in western Oregon.

Science.gov (United States)

Glen C. Crouch

1980-01-01

Effects of plastic mesh cages designed to protect Douglas-fir seedlings from animals were evaluated in western Oregon. In two tests over 5-year periods, caging increased survival by 0 and 13 percent and increased height growth by 0.8 and 1.2 feet compared with uncaged trees. Benefits from caging might have been greater if damage had been more prevalent during the tests...

Depopulation of Caged Layer Hens with a Compressed Air Foam System

Directory of Open Access Journals (Sweden)

Shailesh Gurung

2018-01-01

Full Text Available During the 2014–2015 US highly pathogenic avian influenza (HPAI outbreak, 50.4 million commercial layers and turkeys were affected, resulting in economic losses of $3.3 billion. Rapid depopulation of infected poultry is vital to contain and eradicate reportable diseases like HPAI. The hypothesis of the experiment was that a compressed air foam (CAF system may be used as an alternative to carbon dioxide (CO2 inhalation for depopulating caged layer hens. The objective of this study was to evaluate corticosterone (CORT and time to cessation of movement (COM of hens subjected to CAF, CO2 inhalation, and negative control (NEG treatments. In Experiment 1, two independent trials were conducted using young and spent hens. Experiment 1 consisted of five treatments: NEG, CO2 added to a chamber, a CO2 pre-charged chamber, CAF in cages, and CAF in a chamber. In Experiment 2, only spent hens were randomly assigned to three treatments: CAF in cages, CO2 added to a chamber, and aspirated foam. Serum CORT levels of young hens were not significantly different among the CAF in cages, CAF in a chamber, NEG control, and CO2 inhalation treatments. However, spent hens subjected to the CAF in a chamber had significantly higher CORT levels than birds in the rest of the treatments. Times to COM of spent hens subjected to CAF in cages and aspirated foam were significantly greater than of birds exposed to the CO2 in a chamber treatment. These data suggest that applying CAF in cages is a viable alternative for layer hen depopulation during a reportable disease outbreak.

(reprocessed)CAGE_peaks_annotation - FANTOM5 | LSDB Archive [Life Science Database Archive metadata

Lifescience Database Archive (English)

Full Text Available switchLanguage; BLAST Search Image Search Home About Archive Update History Data List Contact us FANTOM...: ftp://ftp.biosciencedbc.jp/archive/fantom5/datafiles/reprocessed/hg38_latest/extra/CAGE_peaks_annotation/ ...e URL: ftp://ftp.biosciencedbc.jp/archive/fantom5/datafiles/reprocessed/mm10_latest/extra/CAGE_peaks_annotat...te History of This Database Site Policy | Contact Us (reprocessed)CAGE_peaks_annotation - FANTOM5 | LSDB Archive ...

(reprocessed)CAGE_peaks_expression - FANTOM5 | LSDB Archive [Life Science Database Archive metadata

Lifescience Database Archive (English)

Full Text Available switchLanguage; BLAST Search Image Search Home About Archive Update History Data List Contact us FANTOM...sciencedbc.jp/archive/fantom5/datafiles/reprocessed/hg38_latest/extra/CAGE_peaks_expression/ File size: 3.3 ...tp.biosciencedbc.jp/archive/fantom5/datafiles/reprocessed/mm10_latest/extra/CAGE_peaks_expression/ File size...f This Database Site Policy | Contact Us (reprocessed)CAGE_peaks_expression - FANTOM5 | LSDB Archive ...

Sex effect in mutual olfactory relationships of individually caged rabbits

Directory of Open Access Journals (Sweden)

Alessandro Finzi

2015-12-01

Full Text Available To assess the sex influence on sniffing behavior of rabbits, sets of three rabbits each were located for seven days in contiguous cages divided by a metal wall with holes that prevented the neighboring rabbits to see each other. A buck was located in the central cage, with a doe at each side. Rabbit behavior was video recorded to observe animals sniffing with the muzzle near the wall. The bucks displayed an olfactory preference towards one of the two does, which decreased in few days. The significance was p  0.05. The interest of bucks towards the does was also characterized by a frenetic scratching of the separation wall, contemporary with intense sniffing, displayed only for the first 35 min of the first day. The sniffing behavior of does at the central cage housing the male was not so marked as in bucks, and it progressively changed across the trial (p < 0.01. In conclusion, rabbits establish a transitory sex-oriented olfactory relationship with the conspecifics housed in contiguous cages, which looks no longer necessary once the rabbits have recognized each other.

Geomechanics of fracture caging in wellbores

NARCIS (Netherlands)

Weijermars, R.; Zhang, X.; Schultz-Ela, D.

2013-01-01

This study highlights the occurrence of so-called ‘fracture cages’ around underbalanced wellbores, where fractures cannot propagate outwards due to unfavourable principal stress orientations. The existence of such cages is demonstrated here by independent analytical and numerical methods. We explain

Application of titanium and polyetheretherketone cages in the treatment of pyogenic spondylodiscitis.

Science.gov (United States)

Schomacher, Markus; Finger, Tobias; Koeppen, Daniel; Süss, Olaf; Vajkoczy, Peter; Kroppenstedt, Stefan; Cabraja, Mario

2014-12-01

Surgical treatment of a pyogenic spondylodiscitis (PSD) involves a fixation and debridement of the affected segment combined with a specific antibiotic therapy. To achieve a proper stability and to avoid pseudarthrosis and kyphotic malposition many surgeons favour the interposition of an anterior graft. Besides autologous bone grafts titanium (TTN) cages have gained acceptance in the treatment of PSD. Polyetheretherketone (PEEK) cages have a more favourable modulus of elasticity than TTN. We compared both cage types. Primary endpoints were the rate of reinfection and radiological results. From 2004 to 2013 51 patients underwent surgery for PSD with fixation and TTN or PEEK cage-implantation. While lumbar patients underwent a partial discectomy by the posterior approach, discs of the cervical and thoracic patients had been totally removed from anterior. Clinical and radiological parameters were assessed in 37 eligible patients after a mean of 20.4 months. 21 patients received a PEEK- and 16 patients a TTN-cage. A reinfection after surgery and 3 months of antibiotic therapy was not observed. Solid arthrodesis was found in 90.5% of the PEEK-group and 100% of the TTN-group. A segmental correction could be achieved in both groups. Nonetheless, a cage subsidence was observed in 70.3% of all cases. Comparison of radiological results revealed no differences between both groups. A debridement and fixation with anterior column support in combination with an antibiotic therapy appear to be the key points for successful treatment of PSD. The application of TTN- or PEEK-cages does not appear to influence the radiological outcome or risk of reinfection, neither does the extent of disc removal in this clinical subset. Copyright © 2014 Elsevier B.V. All rights reserved.

Reinventing the wheel: comparison of two wheel cage styles for assessing mouse voluntary running activity.

Science.gov (United States)

Seward, T; Harfmann, B D; Esser, K A; Schroder, E A

2018-04-01

Voluntary wheel cage assessment of mouse activity is commonly employed in exercise and behavioral research. Currently, no standardization for wheel cages exists resulting in an inability to compare results among data from different laboratories. The purpose of this study was to determine whether the distance run or average speed data differ depending on the use of two commonly used commercially available wheel cage systems. Two different wheel cages with structurally similar but functionally different wheels (electromechanical switch vs. magnetic switch) were compared side-by-side to measure wheel running data differences. Other variables, including enrichment and cage location, were also tested to assess potential impacts on the running wheel data. We found that cages with the electromechanical switch had greater inherent wheel resistance and consistently led to greater running distance per day and higher average running speed. Mice rapidly, within 1-2 days, adapted their running behavior to the type of experimental switch used, suggesting these running differences are more behavioral than due to intrinsic musculoskeletal, cardiovascular, or metabolic limits. The presence of enrichment or location of the cage had no detectable impact on voluntary wheel running. These results demonstrate that mice run differing amounts depending on the type of cage and switch mechanism used and thus investigators need to report wheel cage type/wheel resistance and use caution when interpreting distance/speed run across studies. NEW & NOTEWORTHY The results of this study highlight that mice will run different distances per day and average speed based on the inherent resistance present in the switch mechanism used to record data. Rapid changes in running behavior for the same mouse in the different cages demonstrate that a strong behavioral factor contributes to classic exercise outcomes in mice. Caution needs to be taken when interpreting mouse voluntary wheel running activity to

Non-fusion rates in anterior cervical discectomy and implantation of empty polyetheretherketone cages.

Science.gov (United States)

Pechlivanis, Ioannis; Thuring, Theresa; Brenke, Christopher; Seiz, Marcel; Thome, Claudius; Barth, Martin; Harders, Albrecht; Schmieder, Kirsten

2011-01-01

A prospective analysis. Our aim was to assess the radiographically detectable bony fusion in patients with anterior cervical discectomy (ACD) and polyetheretherketone (PEEK)-cage implantation without additional filling. Furthermore, clinical data of patients with and without fusion were compared. PEEK-cage implantation is performed in cervical spinal surgery because of its benefits. However, fusion rates without filling of the cage have not been reported. Patients selected for ACD with PEEK-cage implantation prospectively underwent plain radiography in anterior-posterior and lateral projections during the postoperative hospital stay and at follow-up. Furthermore, clinical status was evaluated using the Odom scale, the Short Form-36, the Visual Analog Scale (VAS) for arm and neck pain, and the cervical Oswestry score. Fusion status, migration, and subsidence of the PEEK cage were evaluated on the basis of the lateral radiographs. Fusion was confirmed by presence of continuous trabecular bone bridges in the disc space. To exclude an influence of the cage on the evaluation of fusion rates, fusion was evaluated in analogous fashion retrospectively in a control group. A total of 52 patients underwent ACD and interbody fusion. One-level surgery was performed in 44 patients and 2-level surgery in 8 patients. A total of 60 ACD and interbody fusions with a PEEK cage were analyzed. A majority of operations were at the C5/6 level (40 patients, 77%). Cage height was 4 mm in 32 cases, 5 mm in 23 cases, and 6 mm in 5 cases. Bony fusion was present at 43 treated levels (71.7%), whereas at 17 levels (28.3%) no fusion was found. Statistical analysis revealed no significant difference between the fusion and non-fusion groups regarding time to follow-up, implanted cage height. Short Form-36, cervical Oswestry score, VAS arm and neck, or Odom criteria. In the control group, ACD was performed in 29 patients (42 levels; 18 one-level and 12 two-level operations). Bony fusion was present

Demonstration of Load-Follow Simulation with VERA-CS and Standalone BISON

Energy Technology Data Exchange (ETDEWEB)

Stimpson, Shane G. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-01-24

In this report, load-follow simulations using VERA-CS with one-way coupling to standalone BISON has been demonstrated including both a single rod with a full cycle of load-follow operations and a quarter-core model with a single month of load-follow.

Parametric sensitivity study for solar-assisted heat-pump systems

Science.gov (United States)

White, N. M.; Morehouse, J. H.

1981-07-01

The engineering and economic parameters affecting life-cycle costs for solar-assisted heat pump systems are investigted. The change in energy usage resulting from each engineering parameter varied was developed from computer simulations, and is compared with results from a stand-alone heat pump system. Three geographical locations are considered: Washington, DC, Fort Worth, TX, and Madison, WI. Results indicate that most engineering changes to the systems studied do not provide significant energy savings. The most promising parameters to ary are the solar collector parameters tau (-) and U/sub L/ the heat pump capacity at design point, and the minimum utilizable evaporator temperature. Costs associated with each change are estimated, and life-cycle costs computed for both engineering parameters and economic variations in interest rate, discount rate, tax credits, fuel unit costs and fuel inflation rates. Results indicate that none of the feasibile engineering changes for the system configuration studied will make these systems economically competitive with the stand-alone heat pump without a considerable tax credit.

A Mobile Phone Faraday Cage

Science.gov (United States)

French, M. M. J.

2011-01-01

A Faraday cage is an interesting physical phenomenon where an electromagnetic wave can be excluded from a volume of space by enclosure with an electrically conducting material. The practical application of this in the classroom is to block the signal to a mobile phone by enclosing it in a metal can. The background of the physics behind this is…

Environmental impacts of producing bioethanol and biobased lactic acid from standalone and integrated biorefineries using a consequential and an attributional life cycle assessment approach

DEFF Research Database (Denmark)

Parajuli, Ranjan; Knudsen, Marie Trydeman; Birkved, Morten

2017-01-01

: a standalone system producing bioethanol from winter wheat-straw (system A), a standalone system producing biobased lactic acid from alfalfa (system B), and an integrated biorefinery system (system C) combining the two standalone systems and producing both bioethanol and lactic acid. The synergy...

An Improved Method for Sizing Standalone Photovoltaic Systems Using Generalized Regression Neural Network

Directory of Open Access Journals (Sweden)

Tamer Khatib

2014-01-01

Full Text Available In this research an improved approach for sizing standalone PV system (SAPV is presented. This work is an improved work developed previously by the authors. The previous work is based on the analytical method which faced some concerns regarding the difficulty of finding the model’s coefficients. Therefore, the proposed approach in this research is based on a combination of an analytical method and a machine learning approach for a generalized artificial neural network (GRNN. The GRNN assists to predict the optimal size of a PV system using the geographical coordinates of the targeted site instead of using mathematical formulas. Employing the GRNN facilitates the use of a previously developed method by the authors and avoids some of its drawbacks. The approach has been tested using data from five Malaysian sites. According to the results, the proposed method can be efficiently used for SAPV sizing whereas the proposed GRNN based model predicts the sizing curves of the PV system accurately with a prediction error of 0.6%. Moreover, hourly meteorological and load demand data are used in this research in order to consider the uncertainty of the solar energy and the load demand.

Effect of lipopolysaccharide on sickness behaviour in hens kept in cage and free range environments.

Science.gov (United States)

Gregory, N G; Payne, S R; Devine, C D; Cook, C J

2009-08-01

The aim of this study was to assess whether environmental enrichment and environmental conditions can influence the expression of sickness behaviour. The behaviour in response to injection of lipopolysaccharide or saline was examined in a total of 96 62-weeks old hatchmate hens kept in a free range or cage environment. There were eight experimental treatments, each with 12 birds. Half the birds were sourced from a commercial cage layer unit (C/-) and half from a commercial free range unit (FR/-). After intraperitoneal injection with either lipopolysaccharide or saline (as a control), the hens were placed in either a cage (-/C) or free range (-/FR) environment. Lipopolysaccharide caused greater suppression of activity in free range (FR/FR) than in caged hens, including less walking (53% reduction), roosting (-86%) and preening (-60%) (pfree range, nor in free range birds introduced to cages, suggesting that both the presence of and the familiarity with an environment affected sickness behaviour patterns. Increased sleeping was the most consistent response (+147%; pfree range layer hens can express a greater range of sickness behaviours than caged hens, and this may make it more difficult to recognise disease expression in the caged environment.

Biomechanical evaluation of immediate stability with rectangular versus cylindrical interbody cages in stabilization of the lumbar spine

Directory of Open Access Journals (Sweden)

Webb John K

2002-10-01

Full Text Available Abstract Background Recent cadaver studies show stability against axial rotation with a cylindrical cage is marginally superior to a rectangular cage. The purpose of this biomechanical study in cadaver spine was to evaluate the stability of a new rectangular titanium cage design, which has teeth similar to the threads of cylindrical cages to engage the endplates. Methods Ten motion segments (five L2-3, five L4-5 were tested. From each cadaver spine, one motion segment was fixed with a pair of cylindrical cages (BAK, Sulzer Medica and the other with paired rectangular cages (Rotafix, Corin Spinal. Each specimen was tested in an unconstrained state, after cage introduction and after additional posterior translaminar screw fixation. The range of motion (ROM in flexion-extension, lateral bending, and rotation was tested in a materials testing machine, with +/- 5 Nm cyclical load over 10 sec per cycle; data from the third cycle was captured for analysis. Results ROM in all directions was significantly reduced (p Conclusions There was no significant difference in immediate stability in any direction between the threaded cylindrical cage and the new design of the rectangular cage with endplate teeth.

Do position and size matter? An analysis of cage and placement variables for optimum lordosis in PLIF reconstruction.

Science.gov (United States)

Landham, Priyan R; Don, Angus S; Robertson, Peter A

2017-11-01

To examine monosegmental lordosis after posterior lumbar interbody fusion (PLIF) surgery and relate lordosis to cage size, shape, and placement. Eighty-three consecutive patients underwent single-level PLIF with paired identical lordotic cages involving a wide decompression and bilateral facetectomies. Cage parameters relating to size (height, lordosis, and length) and placement (expressed as a ratio relative to the length of the inferior vertebral endplate) were recorded. Centre point ratio (CPR) was the distance to the centre of both cages and indicated mean position of both cages. Posterior gap ratio (PGR) was the distance to the most posterior cage and indicated position and cage length indirectly. Relationships between lordosis and cage parameters were explored. Mean lordosis increased by 5.98° (SD 6.86°). The cages used varied in length from 20 to 27 mm, in lordosis from 10° to 18°, and in anterior cage height from 10 to 17 mm. The mean cage placement as determined by CPR was 0.54 and by PGR was 0.16. The significant correlations were: both CPR and PGR with lordosis gain at surgery (r = 0.597 and 0.537, respectively, p lordosis with the final lordosis (r = 0.234, p lordosis (r = -0.297, p lordosis during PLIF surgery. Anterior placement with sufficient "clear space" behind the cages is recommended. In addition, cages should be of moderate height and length, so that they act as an effective pivot for lordosis.

CAGE peaks - FANTOM5 | LSDB Archive [Life Science Database Archive metadata

Lifescience Database Archive (English)

Full Text Available switchLanguage; BLAST Search Image Search Home About Archive Update History Data List Contact us FANTOM...E Data file File name: CAGE_peaks File URL: ftp://ftp.biosciencedbc.jp/archive/fantom... This Database Database Description Download License Update History of This Database Site Policy | Contact Us CAGE peaks - FANTOM5 | LSDB Archive ...

Reducing organic contamination of shallow areas in brackish lagoons during rearing fish in cages in polyculture

Directory of Open Access Journals (Sweden)

P. Shekk

2017-07-01

Full Text Available Purpose. The development of the technology of the controlled rearing of marine fish remains one of the priority strategic trends of development of national mariculture. A study of the possibility of using polyculture for cage culture has a particular interest. Joint cultivation of several species of fish in the same cage, as practice of fish farming has demonstrated, does not have a tangible positive effect. At the same time, the use of cages of special design can provide significant additional fish products through the use of additional aquaculture objects. The ecological state of water areas, where the cages are located, is of great importance. High fish stocking density and the use of artificial feeds can serve as a source of powerful biogenic and organic pollution, which is especially important for shallow water areas with weak water exchange. The purpose of the study is to develop the methods for joint fish production in cage mariculture capable to provide high fish production and to weaken organic pollution of shallow water areas where cage farms are located. Methodology. The studies were conducted in 1999 and 2004. Cages of special design (internal 10 m3 and external 18.75 m3 installed in the brackish Shabolat Lagoon were used for rearing, steelhead trout, haarder, grass goby and round goby in polyculture. The standard aquaculture research methods were used. For express-analysis of environment hydrochemical parameters in cage location area the following devices were used: "ECOTEST-2000 T" (О2, NO2, NO3, NH4, CO2, phosphates, pH; termooksimetr "АJА-101М" (Т; О2; "pH meter-150 M; Refractometer "ATAGO-100" (salinity and water density. Findings. The results of marine fish cultivation in cages in polyculture in the shallow Shabolat lagoon are presented. It has been shown that joint cultivation of salmon, mullet and gobies in specially designed cages in shallow marine lagoons allows using artificial and natural feeds more fully and

Study for elevator cage position during the braking period

Science.gov (United States)

Ungureanu, M.; Crăciun, I.; Bănică, M.; Dăscălescu, A.

2016-08-01

An important problem in order to study an elevator cage position for its braking period is to establish a correlation between the studies in the fields of mechanics and electric. The classical approaches to establish the elevator kinematic parameters are position, velocity and acceleration, but the last studies performed in order to determine the positioning performed by introducing supplementary another parameter - the jerk- which is derived with respect to time of acceleration. Thus we get a precise method for cage motion control for third-order trajectory planning.

Study on Soft Phase Locked Method to Solving the Synchronization Problem of Active Power Filter in Stand-alone Power Grid

DEFF Research Database (Denmark)

Zhuo, Fang; Wu, Longhui; Chen, Zhe

2009-01-01

on zero-cross detection can't work effectively in small rating stand-alone power grid. Then a soft phase locked loop with additional filter is proposed. It can lock the phase angle on to the positive sequence of fundamental voltage accurately and rapidly. It ensures the performance of APF applied...... in the small rating stand-alone power grid. Moreover, the soft phase locked loop is easy to be implemented in a Digital Signal Processor (DSP). Simulation and experimental results validate that the soft phase locked loop has satisfactory performance.......Traditional LC filters can't work stably in small rating stand-alone power grid. So active power filter (APF) is becoming an important tool to solve the power quality problem in small rating stand-alone power grid. In most current detection algorithm of APF, it needs a synchronizing signal. Firstly...

Evaluation of cage designs and feeding regimes for honey bee (Hymenoptera: Apidae) laboratory experiments.

Science.gov (United States)

Huang, Shao Kang; Csaki, Tamas; Doublet, Vincent; Dussaubat, Claudia; Evans, Jay D; Gajda, Anna M; Gregorc, Alex; Hamilton, Michele C; Kamler, Martin; Lecocq, Antoine; Muz, Mustafa N; Neumann, Peter; Ozkirim, Asli; Schiesser, Aygün; Sohr, Alex R; Tanner, Gina; Tozkar, Cansu Ozge; Williams, Geoffrey R; Wu, Lyman; Zheng, Huoqing; Chen, Yan Ping

2014-02-01

The aim of this study was to improve cage systems for maintaining adult honey bee (Apis mellifera L.) workers under in vitro laboratory conditions. To achieve this goal, we experimentally evaluated the impact of different cages, developed by scientists of the international research network COLOSS (Prevention of honey bee COlony LOSSes), on the physiology and survival of honey bees. We identified three cages that promoted good survival of honey bees. The bees from cages that exhibited greater survival had relatively lower titers of deformed wing virus, suggesting that deformed wing virus is a significant marker reflecting stress level and health status of the host. We also determined that a leak- and drip-proof feeder was an integral part of a cage system and a feeder modified from a 20-ml plastic syringe displayed the best result in providing steady food supply to bees. Finally, we also demonstrated that the addition of protein to the bees' diet could significantly increase the level ofvitellogenin gene expression and improve bees' survival. This international collaborative study represents a critical step toward improvement of cage designs and feeding regimes for honey bee laboratory experiments.

Mobile Phone Faraday Cage

OpenAIRE

French, M M J

2011-01-01

A Faraday cage is an interesting physics phenomena where an electromagnetic wave can be excluded from a volume of space by enclosure with an electrically conducting material. The practical application of this in the classroom is to block the signal to a mobile phone by enclosing it in a metal can! The background of the physics behind this is described in some detail followed by a explanation of some demonstrations and experiments which I have used.

The effect of space allowance and cage size on laying hens housed in furnished cages, Part II: Behavior at the feeder.

Science.gov (United States)

Widowski, T M; Caston, L J; Casey-Trott, T M; Hunniford, M E

2017-09-01

Standards for feeder (a.k.a. feed trough) space allowance (SA) are based primarily on studies in conventional cages where laying hens tend to eat simultaneously, limiting feeder space. Large furnished cages (FC) offer more total space and opportunities to perform a greater variety of behaviors, which may affect feeding behavior and feeder space requirements. Our objective was to determine the effects of floor/feeder SA on behavior at the feeder. LSL-Lite hens were housed in FC equipped with a nest, perches, and a scratch mat. Hens with SA of either 520 cm2 (Low; 8.9 cm feeder space/hen) or 748 cm2 (High; 12.8 cm feeder space/hen) per bird resulted in groups of 40 vs. 28 birds in small FC (SFC) and 80 vs. 55 in large FC (LFC). Chain feeders ran at 0500, 0800, 1100, 1400, and 1700 with lights on at 0500 and off at 1900 hours. Digital recordings of FC were scanned at chain feeder onset and every 15 min for one h after (5 scans × 5 feeding times × 2 d) to count the number of birds with their head in the feeder. All occurrences of aggressive pecks and displacements during 2 continuous 30-minute observations at 0800 h and 1700 h also were counted. Mixed model repeated analyses tested the effects of SA, cage size, and time on the percent of hens feeding, and the frequency of aggressive pecks and displacements. Surprisingly, the percent of birds feeding simultaneously was similar regardless of cage size (LFC: 23.0 ± 0.9%; SFC: 24.0 ± 1.0%; P = 0.44) or SA (Low: 23.8 ± 0.9%; High: 23.3 ± 1.0%; P = 0.62). More birds were observed feeding at 1700 h (35.3 ± 0.1%) than any at other time (P Feeder use differed by cage area (nest, middle, or scratch) over the d (P feeder competition at the Low SA in this study. © The Author 2017. Published by Oxford University Press on behalf of Poultry Science Association.

Solid-State Gas Adsorption Studies with Discrete Palladium(II) [Pd2 (L)4 ]4+ Cages.

Science.gov (United States)

Preston, Dan; White, Keith F; Lewis, James E M; Vasdev, Roan A S; Abrahams, Brendan F; Crowley, James D

2017-08-04

The need for effective CO 2 capture systems remains high, and due to their tunability, metallosupramolecular architectures are an attractive option for gas sorption. While the use of extended metal organic frameworks for gas adsorption has been extensively explored, the exploitation of discrete metallocage architectures to bind gases remains in its infancy. Herein the solid state gas adsorption properties of a series of [Pd 2 (L) 4 ] 4+ lantern shaped coordination cages (L = variants of 2,6-bis(pyridin-3-ylethynyl)pyridine), which had solvent accessible internal cavities suitable for gas binding, have been investigated. The cages showed little interaction with dinitrogen gas but were able to take up CO 2 . The best performing cage reversibly sorbed 1.4 mol CO 2 per mol cage at 298 K, and 2.3 mol CO 2 per mol cage at 258 K (1 bar). The enthalpy of binding was calculated to be 25-35 kJ mol -1 , across the number of equivalents bound, while DFT calculations on the CO 2 binding in the cage gave ΔE for the cage-CO 2 interaction of 23-28 kJ mol -1 , across the same range. DFT modelling suggested that the binding mode is a hydrogen bond between the carbonyl oxygen of CO 2 and the internally directed hydrogen atoms of the cage. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Chiral Organic Cages with a Triple-Stranded Helical Structure Derived from Helicene.

Science.gov (United States)

Malik, Abaid Ullah; Gan, Fuwei; Shen, Chengshuo; Yu, Na; Wang, Ruibin; Crassous, Jeanne; Shu, Mouhai; Qiu, Huibin

2018-02-28

We report the use of helicene with an intrinsic helical molecular structure to prepare covalent organic cages via imine condensation. The organic cages revealed a [3+2]-type architecture containing a triple-stranded helical structure with three helicene units arranged in a propeller-like fashion with the framework integrally twisted. Such structural chirality was retained upon dissolution in organic solvents, as indicated by a strong diastereotopy effect in proton NMR and unique Cotton effects in circular dichroism spectra. Further study on chiral adsorption showed that the chiral organic cages possess considerable enantioselectivity toward a series of aromatic racemates.

Modeling and Control of the Distributed Power Converters in a Standalone DC Microgrid

Directory of Open Access Journals (Sweden)

Xiaodong Lu

2016-03-01

Full Text Available A standalone DC microgrid integrated with distributed renewable energy sources, energy storage devices and loads is analyzed. To mitigate the interaction among distributed power modules, this paper describes a modeling and control design procedure for the distributed converters. The system configuration and steady-state analysis of the standalone DC microgrid under study are discussed first. The dynamic models of the distributed converters are then developed from two aspects corresponding to their two operating modes, device-regulating mode and bus-regulating mode. Average current mode control and linear compensators are designed accordingly for each operating mode. The stability of the designed system is analyzed at last. The operation and control design of the system are verified by simulation results.

A Three-Port Topology Comparison for a Low Power Stand-Alone Photovoltaic System

DEFF Research Database (Denmark)

Mira Albert, Maria del Carmen; Knott, Arnold; Andersen, Michael A. E.

2014-01-01

Three-port converter (TPC) topologies for renewable energy systems aim to provide higher efficiency and power density than conventional cascaded structures. This work proposes an analytical comparison of different TPC topologies for a photovoltaic LED lamp stand-alone system. A comparison using c...... component stress factor (CSF) is performed, which gives a quantitative measure of the performance of the converter. The candidate topologies are compared to each other according to a defined LED lighting strategy and a solar irradiation profile.......Three-port converter (TPC) topologies for renewable energy systems aim to provide higher efficiency and power density than conventional cascaded structures. This work proposes an analytical comparison of different TPC topologies for a photovoltaic LED lamp stand-alone system. A comparison using...

Preinjector for Linac 1, Faraday cage

CERN Multimedia

1974-01-01

The 50 MeV Linac 1 started up in 1958 as injector to the 26 GeV PS, with a 520 kV Cockcroft-Walton generator as its preinjector, housed in a vast Faraday cage, visible here. When the Cockcroft-Walton broke down in 1973, it was replaced by a much smaller SAMES generator, of the kind used for electrostatic separators. From 1980 on, Linac 2 took over as injector for the 800 MeV Booster, and Linac 1 continued as injector for LEAR. In 1984, the electrostatic preinjector (i.e. the Faraday cage with its contents, SAMES generator and all) was replaced by a 520 keV RFQ. At the lower left corner we see the HV connectors to the SAMES generator, at the right edge part of the opened electronics-platform. Jean-Luc Vallet sees to it that all parts are properly grounded. See also 7403073X, 7403074X, 7403081X, 7403083X.

The fabrication of plastic cages for suspension in mass air flow racks.

Science.gov (United States)

Nielsen, F H; Bailey, B

1979-08-01

A cage for suspension in mass air flow racks was constructed of plastic and used to house rats. Little or no difficulty was encountered with the mass air flow rack-suspended cage system during the 4 years it was used for the study of trace elements.

Anterior lumbar fusion with titanium threaded and mesh interbody cages.

Science.gov (United States)

Rauzzino, M J; Shaffrey, C I; Nockels, R P; Wiggins, G C; Rock, J; Wagner, J

1999-12-15

The authors report their experience with 42 patients in whom anterior lumbar fusion was performed using titanium cages as a versatile adjunct to treat a wide variety of spinal deformity and pathological conditions. These conditions included congenital, degenerative, iatrogenic, infectious, traumatic, and malignant disorders of the thoracolumbar spine. Fusion rates and complications are compared with data previously reported in the literature. Between July 1996 and July 1999 the senior authors (C.I.S., R.P.N., and M.J.R.) treated 42 patients by means of a transabdominal extraperitoneal (13 cases) or an anterolateral extraperitoneal approach (29 cases), 51 vertebral levels were fused using titanium cages packed with autologous bone. All vertebrectomies (27 cases) were reconstructed using a Miami Moss titanium mesh cage and Kaneda instrumentation. Interbody fusion (15 cases) was performed with either the BAK titanium threaded interbody cage (in 13 patients) or a Miami Moss titanium mesh cage (in two patients). The average follow-up period was 14.3 months. Seventeen patients had sustained a thoracolumbar burst fracture, 12 patients presented with degenerative spinal disorders, six with metastatic tumor, four with spinal deformity (one congenital and three iatrogenic), and three patients presented with spinal infections. In five patients anterior lumbar interbody fusion (ALIF) was supplemented with posterior segmental fixation at the time of the initial procedure. Of the 51 vertebral levels treated, solid arthrodesis was achieved in 49, a 96% fusion rate. One case of pseudarthrosis occurred in the group treated with BAK cages; the diagnosis was made based on the patient's continued mechanical back pain after undergoing L4-5 ALIF. The patient was treated with supplemental posterior fixation, and successful fusion occurred uneventfully with resolution of her back pain. In the group in which vertebrectomy was performed there was one case of fusion failure in a patient with

Dye-sensitization of CdS nano-cage - A density functional theory approach

Energy Technology Data Exchange (ETDEWEB)

Jain, Kalpna; Singh, Kh. S. [Department of Physics, D. J. College, Baraut, U.P.-250611 (India); Kishor, Shyam [Department of Chemistry, J. V. College, Baraut, U.P.-250611 (India); Josefsson, Ida; Odelius, Michael [Fysikum, Albanova University Center, Stockholm University, S-106 91 Stockholm (Sweden); Ramaniah, Lavanya M. [High Pressure and Synchrotron Radiation Physics Division, Bhabha Atomic Research Centre, Trombay, Mumbai-400085 (India)

2016-05-23

Quantum dots a few nanometer in size exhibit unique properties in comparison to bulk due to quantum confinement. Their properties can be tuned according to their sizes. Dye sensitized quantum dot (DSQD) solar cells are based on the same principle with surface dangling bonds as a challenge. Researches have shown the existence and stability of nano-cages which are assembled such as to minimize the surface dangling bonds and hence maximize stability. Here, we report a first principles DFT study of optical and electronic properties of CdS-cage (Cd{sub 34}S{sub 34}) sensitized with nkx-2388 dye in three different geometric configurations of dye attachment. A significant distortion is found to occur in the geometric structure of the cage when it interacts strongly with the dye. The relative positioning of dye and cage energy levels is found to be different in different configurations. The absorption spectrum has been analyzed with the help of natural transition orbitals (NTO).

A maximum power point tracking scheme for a 1kw stand-alone ...

African Journals Online (AJOL)

A maximum power point tracking scheme for a 1kw stand-alone solar energy based power supply. ... Nigerian Journal of Technology ... A method for efficiently maximizing the output power of a solar panel supplying a load or battery bus under ...

Protein cages and synthetic polymers: a fruitful symbiosis for drug delivery applications, bionanotechnology and materials science.

Science.gov (United States)

Rother, Martin; Nussbaumer, Martin G; Renggli, Kasper; Bruns, Nico

2016-11-07

Protein cages are hollow protein nanoparticles, such as viral capsids, virus-like particles, ferritin, heat-shock proteins and chaperonins. They have well-defined capsule-like structures with a monodisperse size. Their protein subunits can be modified by genetic engineering at predetermined positions, allowing for example site-selective introduction of attachment points for functional groups, catalysts or targeting ligands on their outer surface, in their interior and between subunits. Therefore, protein cages have been extensively explored as functional entities in bionanotechnology, as drug-delivery or gene-delivery vehicles, as nanoreactors or as templates for the synthesis of organic and inorganic nanomaterials. The scope of functionalities and applications of protein cages can be significantly broadened if they are combined with synthetic polymers on their surface or within their interior. For example, PEGylation reduces the immunogenicity of protein cage-based delivery systems and active targeting ligands can be attached via polymer chains to favour their accumulation in diseased tissue. Polymers within protein cages offer the possibility of increasing the loading density of drug molecules, nucleic acids, magnetic resonance imaging contrast agents or catalysts. Moreover, the interaction of protein cages and polymers can be used to modulate the size and shape of some viral capsids to generate structures that do not occur with native viruses. Another possibility is to use the interior of polymer cages as a confined reaction space for polymerization reactions such as atom transfer radical polymerization or rhodium-catalysed polymerization of phenylacetylene. The protein nanoreactors facilitate a higher degree of control over polymer synthesis. This review will summarize the hybrid structures that have been synthesized by polymerizing from protein cage-bound initiators, by conjugating polymers to protein cages, by embedding protein cages into bulk polymeric

Exterior egg quality as affected by enrichment resources layout in furnished laying-hen cages.

Science.gov (United States)

Li, Xiang; Chen, Donghua; Meng, Fanyu; Su, Yingying; Wang, Lisha; Zhang, Runxiang; Li, Jianhong; Bao, Jun

2017-10-01

This study aimed to investigate the effects of enrichment resources (a perch, dustbath, and nest) layout in furnished laying-hen cages (FC) on exterior quality of eggs. One hundred and sixty-eight (168) Hy-Line Brown laying hens at 16 weeks of age were randomly distributed to four treatments: small furnished cages (SFC), medium furnished cages type I (MFC-I), medium furnished cages type II (MFC-II), and medium furnished cages type III (MFC-III). Each treatment had 4 replicates or cages with 6 hens for SFC (24 birds for each SFC) and 12 hen/cage for MFC-I, -II, and -III (48 birds for each MFC-I, -II and -III). Following a 2-week acclimation, data collection started at 18 weeks of age and continued till 52 weeks of age. Dirtiness of egg surface or cracked shell as indicators of the exterior egg quality were recorded each week. The results showed that the proportion of cracked or dirty eggs was significantly affected by the FC type (p<0.01) in that the highest proportion of cracked or dirty eggs was found in MFC-I and the lowest proportion of dirty eggs in SFC. The results of this showed that furnished cage types affected both dirty eggs and cracked eggs (p<0.01). The results also indicated that not nest but dustbath lead to more dirty eggs. Only MFC-I had higher dirty eggs at nest than other FC (p< 0.01). The results of dirty eggs in MFC-I and MFC-II compared with SFC and MFC-III seemed suggest that a low position of dustbath led to more dirty eggs. SFC design affected exterior egg quality and the low position of dustbath in FC resulted in higher proportion of dirty eggs.

Effects of Medical Device Regulations on the Development of Stand-Alone Medical Software: A Pilot Study.

Science.gov (United States)

Blagec, Kathrin; Jungwirth, David; Haluza, Daniela; Samwald, Matthias

2018-01-01

Medical device regulations which aim to ensure safety standards do not only apply to hardware devices but also to standalone medical software, e.g. mobile apps. To explore the effects of these regulations on the development and distribution of medical standalone software. We invited a convenience sample of 130 domain experts to participate in an online survey about the impact of current regulations on the development and distribution of medical standalone software. 21 respondents completed the questionnaire. Participants reported slight positive effects on usability, reliability, and data security of their products, whereas the ability to modify already deployed software and customization by end users were negatively impacted. The additional time and costs needed to go through the regulatory process were perceived as the greatest obstacles in developing and distributing medical software. Further research is needed to compare positive effects on software quality with negative impacts on market access and innovation. Strategies for avoiding over-regulation while still ensuring safety standards need to be devised.

Effects of Metabolic Cage Housing on Rat Behavior and Performance in the Social Interaction Test.

Science.gov (United States)

Whittaker, Alexandra L; Lymn, Kerry A; Howarth, Gordon S

2016-01-01

Although the metabolic cage is commonly used for housing nonhuman animals in the laboratory, it has been recognized as constituting a unique stressor. Such an environment would be expected to affect behavioral change in animals housed therein. However, few studies have specifically addressed the nature or magnitude of this change. The current study sought to characterize the behavioral time budget of rats in metabolic cage housing in comparison to that of individually housed animals in standard open-top cages. Rats in metabolic cages spent less time moving, manipulating enrichment, and carrying out rearing behaviors, and there was a corresponding shift toward inactivity. In an applied Social Interaction Test, behavioral scoring implied that metabolic cage housing had an anxiogenic effect. In conclusion, metabolic cage housing produces measurable effects on spontaneous and evoked behavior in rats in the laboratory. These behavioral changes may lead to a negative emotional state in these animals, which could have negative welfare consequences. Further research is needed to quantify the existence and magnitude of such an effect on rat well being.

La cage qui cache : La Cage Dorée de Ruben Alves

Directory of Open Access Journals (Sweden)

Cristina Marinho

2015-01-01

Full Text Available The French Comedy La Cage Dorée (produced by the luso descendant Ruben Alves, 2013 success seems to be mainly due to its clichés of Portuguese epics in Paris, and its miseries may not have been underlined enough. Thus, under this apparently naif portrait an intriguing painting of Portuguese immigrants’ French dis-integration may really be hiding, which is the aim of this essay, on one hand, to bring out and, on the other one, to clarify, by questioning comparative critical common denominators of the two countries.

La cage qui cache : La Cage Dorée de Ruben Alves

Directory of Open Access Journals (Sweden)

Cristina Marinho

2015-12-01

Full Text Available The French Comedy La Cage Dorée (produced by the luso descendant Ruben Alves, 2013 success seems to be mainly due to its clichés of Portuguese epics in Paris, and its miseries may not have been underlined enough. Thus, under this apparently naif portrait an intriguing painting of Portuguese immigrants’ French dis-integration may really be hiding, which is the aim of this essay, on one hand, to bring out and, on the other one, to clarify, by questioning comparative critical common denominators of the two countries.

Finite element analysis of lordosis restoration with anterior longitudinal ligament release and lateral hyperlordotic cage placement.

Science.gov (United States)

Uribe, Juan S; Harris, Jeffrey E; Beckman, J M; Turner, Alexander W L; Mundis, Gregory M; Akbarnia, Behrooz A

2015-04-01

Restoring sagittal alignment is an important factor in the treatment of spinal deformities. Recent investigations have determined that releasing the anterior longitudinal ligament (ALL) and placing hyperlordotic cages can increase lordosis, while minimizing need for 3 column osteotomies. The influences of parameters such as cage height and angle have not been determined. Finite element analysis was employed to assess the extent of lordosis achievable after placement of different sized lordotic cages. A 3-dimensional model of a L3-4 segment was used. Disc distraction was simulated by inserting interbody cages mid-body in the disc space. Analyses were performed in the following conditions: (1) intact, (2) ALL release, (3) ALL release + facetectomy, and (4) ALL release + posterior column osteotomy. Changes in segmental lordosis, disc height, foraminal height, and foraminal area were measured. After ALL resection and insertion of hyperlordotic cages, lordosis was increased in all cases. The lordosis achieved by the shorter cages was less due to posterior disc height maintained by the facet joints. A facetectomy increased segmental lordosis, but led to contact between the spinous processes. For some configurations, a posterior column osteotomy was required if the end goal was to match cage angle to intradiscal angle. Increased segmental lumbar lordosis is achievable with hyperlordotic cages after ALL resection. Increased cage height tended to increase the amount of lordosis achieved, although in some cases additional posterior bone resection was required to maximize lordosis. Further studies are needed to evaluate the impact on regional lumbar lordosis.

An optimized Faraday cage design for electron beam current measurements

International Nuclear Information System (INIS)

Turner, J.N.; Hausner, G.G.; Parsons, D.F.

1975-01-01

A Faraday cage detector is described for measuring electron beam intensity for use with energies up to 1.2 Mev, with the present data taken at 100 keV. The design features a readily changeable limiting aperture and detector cup geometry, and a secondary electron suppression grid. The detection efficiency of the cage is shown to be limited only by primary backscatter through the detector solid angle of escape, which is optimized with respect to primary backscattered electrons and secondary electron escape. The geometry and stopping material of the detection cup are varied, and the results show that for maximum detection efficiency with carbon as the stopping mateiral, the solid angle of escape must be equal to or less than 0.05πsr. The experimental results are consistent within the +-2% accuracy of the detection electronics, and are not limited by the Faraday cage detection efficiency. (author)

Effect of cage tier and age on performance, egg quality and stress ...

African Journals Online (AJOL)

This study was conducted to investigate the effects of cage tier and age on performance characteristics of layer hybrids, egg quality and some stress parameters. Ninety laying hens (hybrid ATAK-S) of similar bodyweights were used in the experiment. They were housed in three-tier conventional battery cages (bottom, ...

Optimal sizing method for stand-alone photovoltaic power systems

Energy Technology Data Exchange (ETDEWEB)

Groumpos, P P; Papageorgiou, G

1987-01-01

The total life-cycle cost of stand-alone photovoltaic (SAPV) power systems is mathematically formulated. A new optimal sizing algorithm for the solar array and battery capacity is developed. The optimum value of a balancing parameter, M, for the optimal sizing of SAPV system components is derived. The proposed optimal sizing algorithm is used in an illustrative example, where a more economical life-cycle cost has bene obtained. The question of cost versus reliability is briefly discussed.

Atomic nitrogen encapsulated in fullerenes: realization of a chemical Faraday cage

International Nuclear Information System (INIS)

Lips, K.

2000-01-01

Fullerenes, C 60 and C 70 , are ideal containers for atomic nitrogen. We will show by electron paramagnetic resonance (EPR) experiments that nitrogen in C 60 keeps its atomic ground state configuration and resides in the center of the cage. This is the first time that atomic nitrogen is stabilized at ambient conditions. The inert shell of the fullerene protects the highly reactive nitrogen from undergoing chemical reactions with the surroundings. The fullerene cage is the chemical analogue of the Faraday cage in case of electrical fields, i.e. it shields off the chemical reactivity. As for the free nitrogen atom, the spins of the three p-electrons of nitrogen in C 60 are parallel (S = 3/2) and the atom has spherical symmetry. Due to the center position of nitrogen in C 60 , extremely sharp EPR lines are observed. This reflects the absence of a strong host-guest interaction and shows that the individuality of nitrogen in the fullerenes is preserved. Further evidence for the almost interaction-free suspension of nitrogen in the fullerene cages is provided by g-factor measurements. These investigations show that magnetic shielding of the host molecules can account for the observed differences between N rate at C 60 and N rate at C 70 . The fullerene cage can be chemically modified without destroying the endohedral complex. The chemical modifications change the symmetry of the molecule which is observed through an additional fine structure in the EPR spectrum. Influences of the modifications on the stability of N rate at C 60 will be discussed. (orig.)

Food consumption and food exchange of caged honey bees using a radioactive labelled sugar solution.

Directory of Open Access Journals (Sweden)

Robert Brodschneider

Full Text Available We measured the distribution of sugar solution within groups of caged honey bees (Apis mellifera under standard in vitro laboratory conditions using 14C polyethylene glycol as a radioactive marker to analyze ingestion by individual bees after group feeding. We studied the impact of different experimental setups by varying the number of bees, age of bees, origin of bees, duration of experiment, the amount of available diet, and the influence of the neurotoxic pesticide imidacloprid in the diet on the feeding and food sharing behavior (trophallaxis. Sugar solution was non-uniformly distributed in bees in 36 out of 135 cages. As a measure of the extent to which the sugar diet was equally distributed between caged bees, we calculated the (inner 80% intake ratio by dividing the intake of the 90th percentile bee by the intake of the 10th percentile bee. This intake ratio ranged from 1.3 to 94.8 in 133 individual cages, further supporting a non-uniform distribution of food among caged bees. We can expect a cage with 10 or 30 bees containing one bee that ingests, on average, the 8.8-fold of the bee in the same cage ingesting the smallest quantity of food. Inner 80% intake ratios were lower in experiments with a permanent or chronic offering of labelled sugar solution compared to temporary or acute feedings. After pooling the data of replicates to achieve a higher statistical power we compared different experimental setups. We found that uniform food distribution is best approached with 10 newly emerged bees per cage, which originate from a brood comb from a single colony. We also investigated the trophallaxis between caged honey bees which originally consumed the diet and newly added bees. Color marked bees were starved and added to the cages in a ratio of 10:5 or 20:20 after the initial set of bees consumed all the labelled sugar solution. The distribution of the labelled sugar solution by trophallaxis within 48 hours to added bees was 25% (10:5 or 45

Food consumption and food exchange of caged honey bees using a radioactive labelled sugar solution.

Science.gov (United States)

Brodschneider, Robert; Libor, Anika; Kupelwieser, Vera; Crailsheim, Karl

2017-01-01

We measured the distribution of sugar solution within groups of caged honey bees (Apis mellifera) under standard in vitro laboratory conditions using 14C polyethylene glycol as a radioactive marker to analyze ingestion by individual bees after group feeding. We studied the impact of different experimental setups by varying the number of bees, age of bees, origin of bees, duration of experiment, the amount of available diet, and the influence of the neurotoxic pesticide imidacloprid in the diet on the feeding and food sharing behavior (trophallaxis). Sugar solution was non-uniformly distributed in bees in 36 out of 135 cages. As a measure of the extent to which the sugar diet was equally distributed between caged bees, we calculated the (inner 80%) intake ratio by dividing the intake of the 90th percentile bee by the intake of the 10th percentile bee. This intake ratio ranged from 1.3 to 94.8 in 133 individual cages, further supporting a non-uniform distribution of food among caged bees. We can expect a cage with 10 or 30 bees containing one bee that ingests, on average, the 8.8-fold of the bee in the same cage ingesting the smallest quantity of food. Inner 80% intake ratios were lower in experiments with a permanent or chronic offering of labelled sugar solution compared to temporary or acute feedings. After pooling the data of replicates to achieve a higher statistical power we compared different experimental setups. We found that uniform food distribution is best approached with 10 newly emerged bees per cage, which originate from a brood comb from a single colony. We also investigated the trophallaxis between caged honey bees which originally consumed the diet and newly added bees. Color marked bees were starved and added to the cages in a ratio of 10:5 or 20:20 after the initial set of bees consumed all the labelled sugar solution. The distribution of the labelled sugar solution by trophallaxis within 48 hours to added bees was 25% (10:5) or 45% (20:20) of the

Stand-Alone Microgrid Inverter Controller Design for Nonlinear, Unbalanced Load with Output Transformer

Directory of Open Access Journals (Sweden)

Jae-Uk Lim

2018-04-01

Full Text Available This paper proposes a technique that compensates for unbalance and nonlinearity in microgrid inverters with power transformers operating in stand-alone mode. When a microgrid inverter is operating in stand-alone mode, providing high-quality power is very important. When an unbalanced, nonlinear load is connected, zero sequence current and negative sequence current occur, which leads to an unbalanced output voltage. This paper examines why the zero sequence component occurs differently depending on the structure of a three-phase transformer connected to the inverter output terminal, and it proposes a method for controlling the zero sequence component. It also uses a resonant controller to remove the harmonics that correspond to the negative sequence component and the nonlinear component. The proposed elements were verified by a Powersim (PSIM simulation.

CAGE_peaks_annotation - FANTOM5 | LSDB Archive [Life Science Database Archive metadata

Lifescience Database Archive (English)

Full Text Available switchLanguage; BLAST Search Image Search Home About Archive Update History Data List Contact us FANTOM...file File name: CAGE_peaks_annotation File URL: ftp://ftp.biosciencedbc.jp/archive/fantom...on Download License Update History of This Database Site Policy | Contact Us CAGE_peaks_annotation - FANTOM5 | LSDB Archive ...

Genome-wide detection and analysis of hippocampus core promoters using DeepCAGE

DEFF Research Database (Denmark)

Valen, Eivind; Pascarella, Giovanni; Chalk, Alistair

2009-01-01

in a given tissue. Here, we present a new method for high-throughput sequencing of 5' cDNA tags-DeepCAGE: merging the Cap Analysis of Gene Expression method with ultra-high-throughput sequence technology. We apply DeepCAGE to characterize 1.4 million sequenced TSS from mouse hippocampus and reveal a wealth...

Equivalence Between Squirrel Cage and Sheet Rotor Induction Motor

Science.gov (United States)

Dwivedi, Ankita; Singh, S. K.; Srivastava, R. K.

2016-06-01

Due to topological changes in dual stator induction motor and high cost of its fabrication, it is convenient to replace the squirrel cage rotor with a composite sheet rotor. For an experimental machine, the inner and outer stator stampings are normally available whereas the procurement of rotor stampings is quite cumbersome and is not always cost effective. In this paper, the equivalence between sheet/solid rotor induction motor and squirrel cage induction motor has been investigated using layer theory of electrical machines, so as to enable one to utilize sheet/solid rotor in dual port experimental machines.

Leadership in Dental Hygiene Degree Completion Programs: A Pilot Study Comparing Stand-Alone Leadership Courses and Leadership-Infused Curricula.

Science.gov (United States)

Smith, Michelle L; Gurenlian, JoAnn R; Freudenthal, Jacqueline J; Farnsworth, Tracy J

2016-05-01

The aim of this study was to define the extent to which leadership and leadership skills are taught in dental hygiene degree completion programs by comparing stand-alone leadership courses/hybrid programs with programs that infuse leadership skills throughout the curricula. The study involved a mixed-methods approach using qualitative and quantitative data. Semi-structured interviews were conducted with program directors and faculty members who teach a stand-alone leadership course, a hybrid program, or leadership-infused courses in these programs. A quantitative comparison of course syllabi determined differences in the extent of leadership content and experiences between stand-alone leadership courses and leadership-infused curricula. Of the 53 U.S. dental hygiene programs that offer degree completion programs, 49 met the inclusion criteria, and 19 programs provided course syllabi. Of the program directors and faculty members who teach a stand-alone leadership course or leadership-infused curriculum, 16 participated in the interview portion of the study. The results suggested that competencies related to leadership were not clearly defined or measurable in current teaching. Reported barriers to incorporating a stand-alone leadership course included overcrowded curricula, limited qualified faculty, and lack of resources. The findings of this study provide a synopsis of leadership content and gaps in leadership education for degree completion programs. Suggested changes included defining a need for leadership competencies and providing additional resources to educators such as courses provided by the American Dental Education Association and the American Dental Hygienists' Association.

Isolating long-wavelength fluctuation from structural relaxation in two-dimensional glass: cage-relative displacement

Science.gov (United States)

Shiba, Hayato; Keim, Peter; Kawasaki, Takeshi

2018-03-01

It has recently been revealed that long-wavelength fluctuation exists in two-dimensional (2D) glassy systems, having the same origin as that given by the Mermin-Wagner theorem for 2D crystalline solids. In this paper, we discuss how to characterise quantitatively the long-wavelength fluctuation in a molecular dynamics simulation of a lightly supercooled liquid. We employ the cage-relative mean-square displacement (MSD), defined on relative displacement to its cage, to quantitatively separate the long-wavelength fluctuation from the original MSD. For increasing system size the amplitude of acoustic long wavelength fluctuations not only increases but shifts to later times causing a crossover with structural relaxation of caging particles. We further analyse the dynamic correlation length using the cage-relative quantities. It grows as the structural relaxation becomes slower with decreasing temperature, uncovering an overestimation by the four-point correlation function due to the long-wavelength fluctuation. These findings motivate the usage of cage-relative MSD as a starting point for analysis of 2D glassy dynamics.

Application of Homochiral Alkylated Organic Cages as Chiral Stationary Phases for Molecular Separations by Capillary Gas Chromatography.

Science.gov (United States)

Xie, Shengming; Zhang, Junhui; Fu, Nan; Wang, Bangjin; Hu, Cong; Yuan, Liming

2016-11-08

Molecular organic cage compounds have attracted considerable attention due to their potential applications in gas storage, catalysis, chemical sensing, molecular separations, etc. In this study, a homochiral pentyl cage compound was synthesized from a condensation reaction of ( S , S )-1,2-pentyl-1,2-diaminoethane and 1,3,5-triformylbenzene. The imine-linked pentyl cage diluted with a polysiloxane (OV-1701) was explored as a novel stationary phase for high-resolution gas chromatographic separation of organic compounds. Some positional isomers were baseline separated on the pentyl cage-coated capillary column. In particular, various types of enantiomers including chiral alcohols, esters, ethers and epoxides can be resolved without derivatization on the pentyl cage-coated capillary column. The reproducibility of the pentyl cage-coated capillary column for separation was investigated using nitrochlorobenzene and styrene oxide as analytes. The results indicate that the column has good stability and separation reproducibility after being repeatedly used. This work demonstrates that molecular organic cage compounds could become a novel class of chiral separation media in the near future.

Application of Homochiral Alkylated Organic Cages as Chiral Stationary Phases for Molecular Separations by Capillary Gas Chromatography

Directory of Open Access Journals (Sweden)

Shengming Xie

2016-11-01

Full Text Available Molecular organic cage compounds have attracted considerable attention due to their potential applications in gas storage, catalysis, chemical sensing, molecular separations, etc. In this study, a homochiral pentyl cage compound was synthesized from a condensation reaction of (S,S-1,2-pentyl-1,2-diaminoethane and 1,3,5-triformylbenzene. The imine-linked pentyl cage diluted with a polysiloxane (OV-1701 was explored as a novel stationary phase for high-resolution gas chromatographic separation of organic compounds. Some positional isomers were baseline separated on the pentyl cage-coated capillary column. In particular, various types of enantiomers including chiral alcohols, esters, ethers and epoxides can be resolved without derivatization on the pentyl cage-coated capillary column. The reproducibility of the pentyl cage-coated capillary column for separation was investigated using nitrochlorobenzene and styrene oxide as analytes. The results indicate that the column has good stability and separation reproducibility after being repeatedly used. This work demonstrates that molecular organic cage compounds could become a novel class of chiral separation media in the near future.

Transparent Flexible Active Faraday Cage Enables In Vivo Capacitance Measurement in Assembled Microsensor.

Science.gov (United States)

Ahmadi, Mahdi; Rajamani, Rajesh; Sezen, Serdar

2017-10-01

Capacitive micro-sensors such as accelerometers, gyroscopes and pressure sensors are increasingly used in the modern electronic world. However, the in vivo use of capacitive sensing for measurement of pressure or other variables inside a human body suffers from significant errors due to stray capacitance. This paper proposes a solution consisting of a transparent thin flexible Faraday cage that surrounds the sensor. By supplying the active sensing voltage simultaneously to the deformable electrode of the capacitive sensor and to the Faraday cage, the stray capacitance during in vivo measurements can be largely eliminated. Due to the transparency of the Faraday cage, the top and bottom portions of a capacitive sensor can be accurately aligned and assembled together. Experimental results presented in the paper show that stray capacitance is reduced by a factor of 10 by the Faraday cage, when the sensor is subjected to a full immersion in water.

Integral type small PWR with stand-alone safety

International Nuclear Information System (INIS)

Makihara, Yoshiaki

2001-01-01

A feasibility study is achieved on an integral type small PWR with stand-alone safety. It is designed to have the following features. (1) The coolant does not leak out at any accidental condition. (2) The fuel failure does never occur while it is supposed on the large scale PWR at the design base accident. (3) At any accidental condition the safety is secured without any support from the outside (stand-alone safety secure). (4) It has self-regulating characteristics and easy controllability. The above features can be satisfied by integrate the steam generator and CRDM in the reactor vessel while the pipe line break has to be considered on the conventional PWR. Several counter measures are planned to satisfy the above features. The economy feature is also attained by several simplifications such as (1) elimination of main coolant piping and pressurizer by the integration of primary cooling system and self-pressurizing, (2) elimination of RCP by application of natural circulating system, (3) elimination of ECCS and accumulator by application of static safety system, (4) large scale volume reduction of the container vessel by application of integrated primary cooling system, (5) elimination of boric acid treatment by deletion of chemical shim. The long operation period such as 10 years can be attained by the application of Gd fuel in one batch refueling. The construction period can be shortened by the standardizing the design and the introduction of modular component system. Furthermore the applicability of the reduced modulation core is also considered. (K. Tsuchihashi)

Stand-Alone Personalized Normative Feedback for College Student Drinkers: A Meta-Analytic Review, 2004 to 2014.

Directory of Open Access Journals (Sweden)

Keri B Dotson

Full Text Available Norms clarification has been identified as an effective component of college student drinking interventions, prompting research on norms clarification as a single-component intervention known as Personalized Normative Feedback (PNF. Previous reviews have examined PNF in combination with other components but not as a stand-alone intervention.To investigate the degree to which computer-delivered stand-alone personalized normative feedback interventions reduce alcohol consumption and alcohol-related harms among college students and to compare gender-neutral and gender-specific PNF.Electronic databases were searched systematically through November 2014. Reference lists were reviewed manually and forward and backward searches were conducted.Outcome studies that compared computer-delivered, stand-alone PNF intervention with an assessment only, attention-matched, or active treatment control and reported alcohol use and harms among college students.Between-group effect sizes were calculated as the standardized mean difference in change scores between treatment and control groups divided by pooled standard deviation. Within-group effect sizes were calculated as the raw mean difference between baseline and follow-up divided by pooled within-groups standard deviation.Eight studies (13 interventions with a total of 2,050 participants were included. Compared to control participants, students who received gender-neutral (dbetween = 0.291, 95% CI [0.159, 0.423] and gender-specific PNF (dbetween = 0.284, 95% CI [0.117, 0.451] reported greater reductions in drinking from baseline to follow-up. Students who received gender-neutral PNF reported 3.027 (95% CI [2.171, 3.882] fewer drinks per week at first follow-up and gender-specific PNF reported 3.089 (95% CI [0.992, 5.186] fewer drinks. Intervention effects were small for harms (dbetween = 0.157, 95% CI [0.037, 0.278].Computer-delivered PNF is an effective stand-alone approach for reducing college student

Stand-Alone Personalized Normative Feedback for College Student Drinkers: A Meta-Analytic Review, 2004 to 2014.

Science.gov (United States)

Dotson, Keri B; Dunn, Michael E; Bowers, Clint A

2015-01-01

Norms clarification has been identified as an effective component of college student drinking interventions, prompting research on norms clarification as a single-component intervention known as Personalized Normative Feedback (PNF). Previous reviews have examined PNF in combination with other components but not as a stand-alone intervention. To investigate the degree to which computer-delivered stand-alone personalized normative feedback interventions reduce alcohol consumption and alcohol-related harms among college students and to compare gender-neutral and gender-specific PNF. Electronic databases were searched systematically through November 2014. Reference lists were reviewed manually and forward and backward searches were conducted. Outcome studies that compared computer-delivered, stand-alone PNF intervention with an assessment only, attention-matched, or active treatment control and reported alcohol use and harms among college students. Between-group effect sizes were calculated as the standardized mean difference in change scores between treatment and control groups divided by pooled standard deviation. Within-group effect sizes were calculated as the raw mean difference between baseline and follow-up divided by pooled within-groups standard deviation. Eight studies (13 interventions) with a total of 2,050 participants were included. Compared to control participants, students who received gender-neutral (dbetween = 0.291, 95% CI [0.159, 0.423]) and gender-specific PNF (dbetween = 0.284, 95% CI [0.117, 0.451]) reported greater reductions in drinking from baseline to follow-up. Students who received gender-neutral PNF reported 3.027 (95% CI [2.171, 3.882]) fewer drinks per week at first follow-up and gender-specific PNF reported 3.089 (95% CI [0.992, 5.186]) fewer drinks. Intervention effects were small for harms (dbetween = 0.157, 95% CI [0.037, 0.278]). Computer-delivered PNF is an effective stand-alone approach for reducing college student drinking and

In silico design of supramolecules from their precursors: odd-even effects in cage-forming reactions.

Science.gov (United States)

Jelfs, Kim E; Eden, Edward G B; Culshaw, Jamie L; Shakespeare, Stephen; Pyzer-Knapp, Edward O; Thompson, Hugh P G; Bacsa, John; Day, Graeme M; Adams, Dave J; Cooper, Andrew I

2013-06-26

We synthesize a series of imine cage molecules where increasing the chain length of the alkanediamine precursor results in an odd-even alternation between [2 + 3] and [4 + 6] cage macrocycles. A computational procedure is developed to predict the thermodynamically preferred product and the lowest energy conformer, hence rationalizing the observed alternation and the 3D cage structures, based on knowledge of the precursors alone.

Late Results of Anterior Cervical Discectomy and Fusion with Interbody Cages

OpenAIRE

Da?l?, Murat; Er, Uygur; ?im?ek, Serkan; Bavbek, Murad

2013-01-01

Study Design Retrospective analysis. Purpose To evaluate the effectiveness of anterior cervical discectomy with fusion for degenerative cervical disc disease. Overview of Literature Anterior spinal surgery originated in the mid-1950s and graft for fusion was also employed. Currently anterior cervical microdiscectomy and fusion with an intervertebral cage is a widely accepted procedure for treatment of cervical disc hernia. Artificial grafts and cages for fusion are preferred because of their ...

Cage and linear structured polysiloxane/epoxy hybrids for coatings: Surface property and film permeability.

Science.gov (United States)

Ma, Yanli; He, Ling; Jia, Mengjun; Zhao, Lingru; Zuo, Yanyan; Hu, Pingan

2017-08-15

Three polysiloxane/epoxy hybrids obtained by evolving cage- or linear-structured polysiloxane into poly glycidyl methacrylate (PGMA) matrix are compared used as coatings. One is the cage-structured hybrid of P(GMA/MA-POSS) copolymer obtained by GMA and methacrylisobutyl polyhedral oligomeric silsesquioxane (MA-POSS) via free radical polymerization, the other two are PGMA/NH 2 -POSS and PGMA/NH 2 -PDMS hybrids by cage-structured aminopropyllsobutyl POSS (NH 2 -POSS) or linear-structured diamino terminated poly(dimethylsiloxane) (NH 2 -PDMS) to cure PGMA. The effect of MA-POSS, NH 2 -POSS and NH 2 -PDMS on polysiloxane/epoxy hybrid films is characterized according to their surface morphology, transparency, permeability, adhesive strength and thermo-mechanical properties. Due to caged POSS tending to agglomerate onto the film surface, P(GMA/MA-POSS) and PGMA/NH 2 -POSS films exhibit much more heterogeneous surfaces than PGMA/NH 2 -PDMS film, but the well-compatibility between epoxy matrix and MA-POSS has provided P(GMA/MA-POSS) film with much higher transmittance (98%) than PGMA/NH 2 -POSS film (24%), PGMA/NH 2 -PDMS film (27%) and traditional epoxy resin film (5%). The introduction of polysiloxane into epoxy matrix is confirmed to create hybrids with strong adhesive strength (526-1113N) and high thermos-stability (T g =262-282°C), especially the cage-structured P(GMA/MA-POSS) hybrid (1113N and 282°C), but the flexible PDMS improves PGMA/NH 2 -PDMS hybrid with much higher storage modulus (519MPa) than PGMA/NH 2 -POSS (271MPa), which suggests that PDMS is advantage in improving the film stiffness than POSS cages. However, cage-structured P(GMA/MA-POSS) and PGMA/NH 2 -POSS indicate higher permeability than PGMA/NH 2 -PDMS and traditional epoxy resin. Comparatively, the cage-structured P(GMA/MA-POSS) hybrid is the best coating in transparency, permeability, adhesive strength and thermostability, but linear-structured PGMA/NH 2 -PDMS hybrid behaviors the best coating in

Method of fitting a cage structure

International Nuclear Information System (INIS)

Takeuchi, Mamoru; Iwasaki, Tsutomu; Ishida, Akira; Yokota, Hirakazu.

1971-01-01

Herein disclosed is a method of fitting together cage structures, each made of a different material. The cage structure may be an ultrahigh speed rotary drum for a centrifuge. An inner cylinder of, for example, Al alloy, to be inserted in an outer cylinder made of a material such as carbon fiber reinforced plastic is filament-wound with a resin-impregnated carbon fiber under application of an axial tensile force to the inner cylinder so as to contract the radius thereof, and then after-cured to cool down to room temperature. The tensile force is then released to permit the radially contracted inner cylinder to elastically recover its original form and to thereby eliminate a gap formed between both cylinders due to aftercure, providing that the width of the gap is equal to that of the radial contraction, determined by Poisson's ratio, of the Al alloy material. Thus, the inner cylinder can be firmly fitted within the outer cylinder in accordance with the elastic deformation of the material. (Ohno, Y.)

Validation of an automatic system (DoubleCage) for detecting the location of animals during preference tests.

Science.gov (United States)

Tsai, P P; Nagelschmidt, N; Kirchner, J; Stelzer, H D; Hackbarth, H

2012-01-01

Preference tests have often been performed for collecting information about animals' acceptance of environmental refinement objects. In numerous published studies animals were individually tested during preference experiments, as it is difficult to observe group-housed animals with an automatic system. Thus, videotaping is still the most favoured method for observing preferences of socially-housed animals. To reduce the observation workload and to be able to carry out preference testing of socially-housed animals, an automatic recording system (DoubleCage) was developed for determining the location of group-housed animals in a preference test set-up. This system is able to distinguish the transition of individual animals between two cages and to record up to 16 animals at the same time (four animals per cage). The present study evaluated the reliability of the DoubleCage system. The data recorded by the DoubleCage program and the data obtained by human observation were compared. The measurements of the DoubleCage system and manual observation of the videotapes are comparable and significantly correlated (P animals and a considerable reduction of animal observation time.

New control strategy of stand-alone brushless doubly-fed induction generator for supplying unbalanced loads in ship shaft power generation system

DEFF Research Database (Denmark)

Liu, Yi; Xu, Wei; Xiong, Fei

2017-01-01

The ship shaft power generation system based on a stand-alone brushless doubly-fed induction generator (BDFIG) have demonstrated excellent saving-energy performance. This paper presents a new control scheme of the stand-alone BDFIG for supplying unbalanced loads in the ship shaft power generation...

Energy saving work of frequency controlled induction cage machine

Energy Technology Data Exchange (ETDEWEB)

Gnacinski, P. [Gdynia Maritime University, Department of Ship Electrical Power Engineering, Morska Str. 8, 81-225 Gdynia (Poland)]. E-mail: piotrg@am.gdynia.pl

2007-03-15

Energy saving work, understood as lowering the supply voltage when load torque is much less than rated, is one way of reducing power losses in an induction cage machine working with a variable load. Reduction in power losses also affects the thermal properties of an induction machine because the energy saving work allows the temperature rise of the windings to decrease. Thanks to a lower temperature of the windings, the same load torque can be carried by a machine of less rated power. The ability of energy saving work to reduce the temperature of windings depends on the thermal properties of an induction machine, which are different in the case of a machine with foreign ventilation and its own ventilation. This paper deals with the thermal effect of energy saving work on a frequency controlled induction cage machine. A comparison of the properties of a machine with its own and outside ventilation is presented. The results of the investigations are shown for a 3 kW induction cage machine with the two previously mentioned ways of ventilation: one provided with a fan placed on a shaft and the other provided with a fan driven by an auxiliary motor.

Energy saving work of frequency controlled induction cage machine

International Nuclear Information System (INIS)

Gnacinski, P.

2007-01-01

Energy saving work, understood as lowering the supply voltage when load torque is much less than rated, is one way of reducing power losses in an induction cage machine working with a variable load. Reduction in power losses also affects the thermal properties of an induction machine because the energy saving work allows the temperature rise of the windings to decrease. Thanks to a lower temperature of the windings, the same load torque can be carried by a machine of less rated power. The ability of energy saving work to reduce the temperature of windings depends on the thermal properties of an induction machine, which are different in the case of a machine with foreign ventilation and its own ventilation. This paper deals with the thermal effect of energy saving work on a frequency controlled induction cage machine. A comparison of the properties of a machine with its own and outside ventilation is presented. The results of the investigations are shown for a 3 kW induction cage machine with the two previously mentioned ways of ventilation: one provided with a fan placed on a shaft and the other provided with a fan driven by an auxiliary motor

New caged neurotransmitter analogs selective for glutamate receptor sub-types based on methoxynitroindoline and nitrophenylethoxycarbonyl caging groups

Czech Academy of Sciences Publication Activity Database

Palma-Cerda, F.; Auger, C.; Crawford, D.J.; Hodgson, A.C.C.; Reynolds, S.J.; Cowell, J.K.; Swift, K.A.D.; Cais, Ondřej; Vyklický ml., Ladislav; Corrie, J.E.T.; Ogden, D.

2012-01-01

Roč. 63, č. 4 (2012), s. 624-634 ISSN 0028-3908 R&D Projects: GA ČR(CZ) GA309/07/0271 Grant - others:EC(XE) LSHM-CT-2007-037765 Institutional research plan: CEZ:AV0Z50110509 Keywords : photolysis * glutamate receptors * caged neurotransmitters Subject RIV: ED - Physiology Impact factor: 4.114, year: 2012

Disparities in Ammonia, Temperature, Humidity, and Airborne Particulate Matter between the Micro-and Macroenvironments of Mice in Individually Ventilated Caging

Science.gov (United States)

Rosenbaum, Matthew D; VandeWoude, Susan; Volckens, John; Johnson, Thomas E

2010-01-01

Animal room environmental parameters typically are monitored with the assumption that the environment within the cage closely mirrors the room environment. This study evaluated that premise by examining macro- (room) and microenvironmental (cage) parameters in individually ventilated cages housing mice with variable amounts of bedding over a period of 17 d without cage changes. Intracage ammonia levels remained within recommended human guidelines but were higher than room levels, confirming that microisolation caging is efficient at preventing ammonia generated from animal waste from escaping into the room. Humidity and temperature within cages were consistently higher than room levels. Particles in the room predominantly consisted of fine particles (diameter less than 2.5 µm), presumably from the ambient atmosphere; some of these particles were found in the cage microenvironment. In addition, mouse activity within cages produced larger particles, and these particles contributed to substantially higher aerosol mass concentrations within the cage. These findings demonstrate that, although cage and room environmental parameters differ, knowledge of room environmental conditions can be used to predict certain conditions within the cage. This association is relevant in that typical animal care standard operating procedures rely on room measurements, not intracage measurements, which arguably are more important for assessing animal welfare. Further, location and ambient climate can influence particle concentrations in the room, and consequently within the animal cage, suggesting local weather patterns and air quality may account for variability among studies conducted at sites that are geographically divergent. PMID:20353692

Freeing Maya Angelou's Caged Bird

OpenAIRE

Graham, Joyce L.

1991-01-01

This study involves a comprehensive examination of one book, Maya Angelou's autobiographical I Know Why Why the Caged Bird Sings, since it was first published in 1970. Recognized as an important literary work, the novel is used in many middle and secondary school classrooms throughout the united States. Additionally, the work often is challenged in public schools on the grounds of its sexual and/or racial content. The purpose of this study included establishing th...

The Stand-alone Heliostat

International Nuclear Information System (INIS)

Garcia Navajas, G. I.; Egea Gea, A.

2000-01-01

The first Autonomous Heliostat has been developed by CIEMAT at PSA facilities in Almeria. This heliostat is an innovative approach to reducing the civil engineering work costs in heliostat fields of central tower plants. Channels, cables and other electric elements have been eliminated in the new heliostat. Thus, one 70-nr, classical T glass/metal heliostat has been adapted to include all the new stand-alone concept components. A PV system is able to drive two sun-tracking DC motors between 5 and 24Vdc, 0 and 15A. The heliostat communicates with the control room 400-m away by using a radio-modem working at 9600 baud. An anemometer, a wind switcher, light and ambient temperature sensors have been installed on the heliostat for self-protection decision-making. A PV panel integrated into the heliostat reflecting surface, eliminates cabling and other elements required for a conventional power supply. Communication lines between master control and local control have been replaced by radio-modem. Testing has validated the technical feasibility of the prototype and quantified the real consumption and efficiencies of new elements. The extra costs produced.by the autonomous concepts are compared with the cost of civil work in conventional heliostat field. (Author) 8 refs

A New Vector Control of Brushless Doubly-Fed Inductor Generator With Transient Current Compensation for Stand-Alone Power Generation Applications

DEFF Research Database (Denmark)

Liu, Yi; Xu, Wei; Yu, Kailiang

2018-01-01

The stand-alone brushless doubly-fed induction generator (BDFIG) with the conventional control strategies suffers heavily from poor dynamic performance especially under heavy load disturbance. This paper presents a new vector control strategy of BDFIG for stand-alone power generation applications...... control strategies, and the results verify the satisfactory dynamic performance of the proposed strategy....

Forced Hot Air to Dry Feces and Kill Bacteria on Transport Cage Flooring

Science.gov (United States)

Due to fecal shedding from positive birds, broiler transport cages can be contaminated with human bacterial pathogens leading to cross contamination of previously negative broilers during live haul. Earlier work has shown that drying soiled or washed cages for 24 to 48 hours can lower or even elimi...

The effect of cage size on reproductive performance and behavior of C57BL/6 mice.

Science.gov (United States)

Whitaker, Julia; Moy, Sheryl S; Saville, Benjamin R; Godfrey, Virginia; Nielsen, Judith; Bellinger, Dwight; Bradfield, John

2007-11-01

Scientific research has yet to conclusively determine the optimal cage size for mice. The authors examined the effect of cage size on mouse breeding performance and on offspring behavior, which can serve as indications of overall well-being. They housed breeding trios of C57BL/6Tac mice in standard or large individually ventilated cages and measured four reproductive parameters: litter size; litter survival to weaning age; average pup weight at 7, 14 and 21 days; and the number of days between litter births. They investigated the behavior of a subset of male and female pups from parents housed in cages of each size in the elevated plus maze test, the open field assay and the acoustic startle test. Cage size had no significant effect on any of the reproductive parameters measured and few or inconsistent effects on behavior in weaned pups.

Acclimatization of mice to different cage types and social groupings with respect to fecal secretion of IgA and corticosterone metabolites

DEFF Research Database (Denmark)

Bundgaard, Cathrine Juel; Kalliokoski, Otto; Abelson, Klas Sp

2012-01-01

genders were housed either in groups of eight in different cage types in open conventional cages, in Individual Ventilated Cages (IVC), in open conventional cages inside a plastic isolator, or in different group sizes (8, 4, 8, 10 or 12 mice in each group) in open conventional cages. Feces were collected...

Stand-alone version of the 11kW Gaia wind turbine

DEFF Research Database (Denmark)

Bindner, H.; Rosas, P.A.C.; Teodorescu, R.

2004-01-01

This report describes the development of a stand-alone version of the 11kW Gaia wind turbine. Various possible configurations are investigated and a configuration using a back-to-back converter is chosen. A model is developed for controller design of thefast controllers of the unit. Controllers...... assessment and controller design a dynamic performance assessment model has been developed....

Suspected Lonely Mouse Syndrome as a Cage Effect in a Drug Safety Study.

Science.gov (United States)

Ye, Xiaobu; Itzoe, MariaLisa; Sarabia-Estrada, Rachel; DeTolla, Louis; Tyler, Betty M; Guarnieri, Michael

2018-01-01

Studies have demonstrated that buprenorphine, a front line drug for veterinary analgesia, may alleviate symptoms of chronic pain. A cage side observation protocol was used to record behavioral signs in a mouse clinical trial of extended release buprenorphine. A retrospective review of the observations for signs of pain and stress revealed that mice given a fivefold overdose of buprenorphine (16.25 mg/kg) showed lethargy and facial signs associated with stress. However, similar signs were observed in the drug-free control mice as early as Day 3 of single-cage housing. This appears to be the first report of cage effects in a clinical trial for a veterinary drug.

Can forced hot air quickly dry feces on transport cage flooring and eliminate campylobacter before cage re-use?

Science.gov (United States)

Allowing feces left on transport coops to dry is an effective way to reduce numbers of viable Campylobacter left by positive flocks. The problem with this approach is that poultry processors do not have the time, space or resources to maintain several times the minimum number of transport cages that...

Evaluating a Pre-Session Homework Exercise in a Standalone Information Literacy Class

Science.gov (United States)

Goetz, Joseph E.; Barber, Catherine R.

2015-01-01

In this study, researchers evaluate a homework exercise assigned before a standalone information literacy session. Students in a Master of Education program completed a worksheet using the ERIC database thesaurus. The researchers conducted pre- and posttests within a single library session to assess student learning, using a control group for…

Lowest-energy cage structures of medium-sized (ZnO){sub n} clusters with n = 15 − 24

Energy Technology Data Exchange (ETDEWEB)

Tang, Lingli; Sai, Linwei [School of Mathematical Sciences, Dalian University of Technology, Dalian 116024, China and College of Advanced Science and Technology, Dalian University of Technology, Dalian 116024 (China); Zhao, Jijun, E-mail: zhaojj@dlut.edu.cn [College of Advanced Science and Technology, Dalian University of Technology, Dalian 116024, China and Key Laboratory of Materials Modification by Laser, Ion and Electron Beams (Dalian University of Technology), Ministry of Education, Dalian 116024 (China); Qiu, Ruifeng [School of Mathematical Sciences, Dalian University of Technology, Dalian 116024 (China)

2015-01-22

Fullerene-like cage structures of medium-sized (ZnO){sub n} clusters with n = 15 − 24 were generated by spiral algorithm and optimized using density functional theory calculations. Most of these lowest-energy cage structures contain only four-membered and six-membered rings, whereas eight-membered rings were found in the lowest-energy cages of (ZnO){sub n} (n = 19, 20, 23, 24). Our best cage configurations either reproduce or prevail the previously reported ones. The size-dependent electronic properties were also discussed.

A Novel Method for Fast Configuration of Energy Storage Capacity in Stand-Alone and Grid-Connected Wind Energy Systems

Directory of Open Access Journals (Sweden)

Haixiang Zang

2016-12-01

Full Text Available In this paper, a novel method is proposed and applied to quickly calculate the capacity of energy storage for stand-alone and grid-connected wind energy systems, according to the discrete Fourier transform theory. Based on practical wind resource data and power data, which are derived from the American Wind Energy Technology Center and HOMER software separately, the energy storage capacity of a stand-alone wind energy system is investigated and calculated. Moreover, by applying the practical wind power data from a wind farm in Fujian Province, the energy storage capacity for a grid-connected wind system is discussed in this paper. This method can also be applied to determine the storage capacity of a stand-alone solar energy system with practical photovoltaic power data.

Impact of Battery’s Model Accuracy on Size Optimization Process of a Standalone Photovoltaic System

Directory of Open Access Journals (Sweden)

Ibrahim Anwar Ibrahim

2016-09-01

Full Text Available This paper presents a comparative study between two proposed size optimization methods based on two battery’s models. Simple and complex battery models are utilized to optimally size a standalone photovoltaic system. Hourly meteorological data are used in this research for a specific site. Results show that by using the complex model of the battery, the cost of the system is reduced by 31%. In addition, by using the complex battery model, the sizes of the PV array and the battery are reduced by 5.6% and 30%, respectively, as compared to the case which is based on the simple battery model. This shows the importance of utilizing accurate battery models in sizing standalone photovoltaic systems.

Net-bottom Cage Inserts for Water Bird Casualties

Directory of Open Access Journals (Sweden)

Jackie Belle

2017-10-01

Full Text Available My Bright Idea is a net-bottomed cage insert, which is used to support pelagic avian casualties. The idea was designed and modified by the International Bird Rescue in California (Bird Rescue.

Does rearing laying hens in aviaries adversely affect long-term welfare following transfer to furnished cages?

Directory of Open Access Journals (Sweden)

Fernanda M Tahamtani

Full Text Available This study tests the hypothesis that hens that are reared in aviaries but produce in furnished cages experience poorer welfare in production than hens reared in caged systems. This hypothesis is based on the suggestion that the spatial restriction associated with the transfer from aviaries to cages results in frustration or stress for the aviary reared birds. To assess the difference in welfare between aviary and cage reared hens in production, non-beak trimmed white leghorn birds from both rearing backgrounds were filmed at a commercial farm that used furnished cage housing. The videos were taken at 19 and 21 weeks of age, following the birds' transition to the production environment at 16 weeks. Videos were analysed in terms of the performance of aversion-related behaviour in undisturbed birds, comfort behaviour in undisturbed birds, and alert behaviour directed to a novel object in the home cage. A decrease in the performance of the former behaviour and increase in the performance of the latter two behaviours indicates improved welfare. The results showed that aviary reared birds performed more alert behaviour near to the object than did cage reared birds at 19 but not at 21 weeks of age (P = 0.03. Blood glucose concentrations did not differ between the treatments (P>0.10. There was a significant difference in mortality between treatments (P = 0.000, with more death in aviary reared birds (5.52% compared to cage birds (2.48%. The higher mortality of aviary-reared birds indicates a negative effect of aviary rearing on bird welfare, whereas the higher duration of alert behavior suggests a positive effect of aviary rearing.

Production performance, use of nest box, and external appearance of two strains of laying hens kept in conventional and enriched cages.

Science.gov (United States)

Onbaşılar, E E; Ünal, N; Erdem, E; Kocakaya, A; Yaranoğlu, B

2015-04-01

The aim of this study was to investigate the differences in production performance, use of nest box, and external appearance of 2 strains of laying hens kept in conventional and enriched cages. Lohmann Brown Classic (LB, n=532) and Lohmann LSL Classic (LW, n=532) hens were housed from 16 to 73 wk in either conventional cages or enriched cages. Enriched cages had a nesting area, scratch pad, perch, and nail shortener. Body weight (BW), hen-day egg production, egg weight, feed intake, feed conversion ratio (FCR), cracked and dirty eggs, use of nest box for lay, and external appearance were determined. Laying period influenced the hen-day egg production, egg weight, feed intake, and feed conversion ratio. Cage type affected the hen-day egg production and feed conversion ratio, while strain affected the egg weight, feed intake, and feed conversion ratio. Laying period×cage type and laying period×strain interactions affected egg production, egg weight, and feed conversion ratio. Both strains preferred to lay in the nest box. Percentages of cracked and dirty eggs of LW hens in enriched cages were higher than that in conventional cages. Most of the dirty eggs laid by both strains were found outside of the nest box. The LW hens laid more dirty eggs than the LB hens. Cage type and cage type×strain interaction were important for total feather score. Final claw length was affected by cage type, strain, and cage type×strain interaction. This study suggests that cage type, strain, and also cage type×strain and period×strain interactions should be considered when alternative housing systems are used. © 2015 Poultry Science Association Inc.

Incomplete Faraday cage effect of helicopters used in platform live-line maintenance

Energy Technology Data Exchange (ETDEWEB)

Cameron, G.W.; Bodger, P.S.; Woudberg, J.J. [University of Canterbury, Christchurch (New Zealand). Dept. of Electrical and Electronic Engineering

1998-03-01

The use of helicopters for maintenance on live overhead transmission lines has become a realistic option. The helicopter blades, body and working platform can be seen as creating an incomplete Faraday cage which may be an enhancement to live-line worker safety. This paper simulates the condition using a Faraday cage which can be dismantled in a controlled laboratory environment, to ascertain the effectiveness of apparatus. (author)

Architecture of clathrin fullerene cages reflects a geometric constraint--the head-to-tail exclusion rule--and a preference for asymmetry.

Science.gov (United States)

Schein, Stan

2009-03-27

Fullerene cages have n trivalent vertices, 12 pentagonal faces, and (n-20)/2 hexagonal faces. The smallest cage in which all of the pentagons are surrounded by hexagons and thus isolated from each other has 60 vertices and is shaped like a soccer ball. The protein clathrin self-assembles into fullerene cages of a variety of sizes and shapes, including smaller ones with adjacent pentagons as well as larger ones, but the variety is limited. To explain the range of clathrin architecture and how these fullerene cages self-assemble, we proposed a hypothesis, the "head-to-tail exclusion rule" (the "Rule"). Of the 5769 small clathrin cage isomers with n< or =60 vertices and adjacent pentagons, the Rule permits just 15, three identified in 1976 and 12 others. A "weak version" of the Rule permits another 99. Based on cryo-electron tomography, Cheng et al. reported six raw clathrin fullerene cages. One was among the three identified in 1976. Here, (1) we identify the remaining five. (2) Four are new and are among the 12 others permitted by the Rule. (3) One, also new, is among the 99 weak version cages. (4) Of particular note, none of the remaining 5565 excluded cages has been identified. These findings provide powerful experimental confirmation of the Rule and the principle on which it is based. (5) Surprisingly, the newly identified clathrin cages are among the least symmetric of those permitted. (6) By devising a method for counting assembly paths, (7) we show that asymmetric cages can be assembled by larger numbers of paths, thus providing a kinetic explanation for the prevalence of asymmetric cages. (8) Finally, we show that operation during cage growth of the Rule greatly increases the likelihood of producing a closed fullerene cage, specifically one of those permitted, but efficient assembly still appears to require internal remodeling.

Mercury and stable isotope signatures in caged marine fish and fish feeds

Energy Technology Data Exchange (ETDEWEB)

Onsanit, Sarayut; Chen, Min; Ke, Caihuan [State Key Laboratory for Marine Environmental Science, College of Oceanography and Environmental Science, Xiamen University, Xiamen 361005 (China); Wang, Wen-Xiong [State Key Laboratory for Marine Environmental Science, College of Oceanography and Environmental Science, Xiamen University, Xiamen 361005 (China)

2012-02-15

Highlights: Black-Right-Pointing-Pointer Mercury concentrations in caged fish were closely related to Hg concentrations in fish feeds. Black-Right-Pointing-Pointer The trophic transfer factor of methylmercury was dependent on fish feeds, and was the highest for fish fed on pellet feeds. Black-Right-Pointing-Pointer Fish farming may be a good way of reducing the human exposure to Hg because Hg levels can be carefully controlled. - Abstract: Total mercury (THg) and methylmercury (MeHg) concentrations were determined in four species of marine caged carnivorous fish, one species of herbivorous fish and three types of fish feeds (dried pellet feed, forage fish and fish viscera), collected from five cage sites in the rural areas along Fujian coastline, China. For the carnivorous fish, the concentrations of THg and MeHg ranged from 0.03 to 0.31 {mu}g/g and from 0.02 to 0.30 {mu}g/g on wet weight basis, respectively. The concentrations were lower for the herbivorous fish with both within the range of 0.01-0.03 {mu}g/g. Out of the three tested fish feeds, tuna viscera contained the highest level of mercury (0.20 {mu}g/g THg and 0.13 {mu}g/g MeHg), with pellet feed containing the lowest level (0.05 {mu}g/g THg and 0.01 {mu}g/g MeHg). The calculated trophic transfer factor of MeHg was the highest (12-64) for fish fed on pellet feeds, and was the lowest for fish fed on tuna viscera. A significant relationship was found between Hg concentrations in caged fish and in fish feeds, thus Hg was primarily accumulated from the diet. Furthermore, the stable isotope {delta}{sup 15}N was positively correlated with the Hg concentration in two caged sites, indicating that {delta}{sup 15}N may be a suitable tool for tracking mercury in caged fish. We conclude that fish farming may be a good way of reducing the human exposure to Hg because mercury levels can be carefully controlled in such farming systems.

Mercury and stable isotope signatures in caged marine fish and fish feeds

International Nuclear Information System (INIS)

Onsanit, Sarayut; Chen, Min; Ke, Caihuan; Wang, Wen-Xiong

2012-01-01

Highlights: ► Mercury concentrations in caged fish were closely related to Hg concentrations in fish feeds. ► The trophic transfer factor of methylmercury was dependent on fish feeds, and was the highest for fish fed on pellet feeds. ► Fish farming may be a good way of reducing the human exposure to Hg because Hg levels can be carefully controlled. - Abstract: Total mercury (THg) and methylmercury (MeHg) concentrations were determined in four species of marine caged carnivorous fish, one species of herbivorous fish and three types of fish feeds (dried pellet feed, forage fish and fish viscera), collected from five cage sites in the rural areas along Fujian coastline, China. For the carnivorous fish, the concentrations of THg and MeHg ranged from 0.03 to 0.31 μg/g and from 0.02 to 0.30 μg/g on wet weight basis, respectively. The concentrations were lower for the herbivorous fish with both within the range of 0.01–0.03 μg/g. Out of the three tested fish feeds, tuna viscera contained the highest level of mercury (0.20 μg/g THg and 0.13 μg/g MeHg), with pellet feed containing the lowest level (0.05 μg/g THg and 0.01 μg/g MeHg). The calculated trophic transfer factor of MeHg was the highest (12–64) for fish fed on pellet feeds, and was the lowest for fish fed on tuna viscera. A significant relationship was found between Hg concentrations in caged fish and in fish feeds, thus Hg was primarily accumulated from the diet. Furthermore, the stable isotope δ 15 N was positively correlated with the Hg concentration in two caged sites, indicating that δ 15 N may be a suitable tool for tracking mercury in caged fish. We conclude that fish farming may be a good way of reducing the human exposure to Hg because mercury levels can be carefully controlled in such farming systems.

Optimum autonomous stand-alone photovoltaic system design on the basis of energy pay-back analysis

International Nuclear Information System (INIS)

Kaldellis, J.K.; Zafirakis, D.; Kondili, E.

2009-01-01

Stand-alone photovoltaic (PV) systems comprise one of the most promising electrification solutions for covering the demand of remote consumers. However, such systems are strongly questioned due to extreme life-cycle (LC) energy requirements. For similar installations to be considered as environmentally sustainable, their LC energy content must be compensated by the respective useful energy production, i.e. their energy pay-back period (EPBP) should be found less than their service period. In this context, an optimum sizing methodology is currently developed, based on the criterion of minimum embodied energy. Various energy autonomous stand-alone PV-lead-acid battery systems are examined and two different cases are investigated; a high solar potential area and a medium solar potential area. By considering that the PV-battery (PV-Bat) system's useful energy production is equal to the remote consumer's electricity consumption, optimum cadmium telluride (CdTe) based systems yield the minimum EPBP (15 years). If achieving to exploit the net PV energy production however, the EPBP is found less than 20 years for all PV types. Finally, the most interesting finding concerns the fact that in all cases examined the contribution of the battery component exceeds 27% of the system LC energy requirements, reflecting the difference between grid-connected and stand-alone configurations.

Magnetic field measurements near stand-alone transformer stations.

Science.gov (United States)

Kandel, Shaiela; Hareuveny, Ronen; Yitzhak, Nir-Mordechay; Ruppin, Raphael

2013-12-01

Extremely low-frequency (ELF) magnetic field (MF) measurements around and above three stand-alone 22/0.4-kV transformer stations have been performed. The low-voltage (LV) cables between the transformer and the LV switchgear were found to be the major source of strong ELF MFs of limited spatial extent. The strong fields measured above the transformer stations support the assessment method, to be used in future epidemiological studies, of classifying apartments located right above the transformer stations as highly exposed to MFs. The results of the MF measurements above the ground around the transformer stations provide a basis for the assessment of the option of implementing precautionary procedures.

Enhanced current and voltage regulators for stand-alone applications

DEFF Research Database (Denmark)

Federico, de Bosio; Pastorelli, Michele; Antonio DeSouza Ribeiro, Luiz

2016-01-01

State feedback decoupling permits to achieve a better dynamic response for Voltage Source in stand-alone applications. The design of current and voltage regulators is performed in the discrete-time domain since it provides better accuracy and allows direct pole placement. As the attainable...... bandwidth of the current loop is mainly limited by computational and PWM delays, a lead compensator structure is proposed to overcome this limitation. The design of the voltage regulator is based on the Nyquist criterion, verifying to guarantee a high sensitivity peak. Discrete-time domain implementation...

John Cage y su influencia en la obra del video artista Nam June Paik

Directory of Open Access Journals (Sweden)

Sarriugarte Gómez, Íñigo

2009-12-01

Full Text Available In 1958, the Korean artist Nam June Paik (*1932; †2006 meets in Germany John Cage (*1912; †1992, avant-garde musician, who was deeply interested in the Zen Buddhism. The meeting with Cage was vital, because the North American composer will convince him to orient his career towards the artistic avant-garde, giving up his facet like classic pianist. The philosophy of Cage is refl ected in compositions like “4’ 33’’, from 1952, where the spectator doesn’t listen the sound of the piano, because this isn’t played, but he listens a silence that is interrupted by the environmental sound. There are several versions of this piece, marking the silences by means of processes at random with the “I Ching”. In this sense, the silence used by John Cage is related to the vacuity of the Zen Buddhism. Also, Paik makes use of silence in numerous works, like “1963 TV Clock”, where 24 colour television sets are manipulated, feeling at the same time the silence, interrupted again by the own momentary circumstances of the spectator. This same infl uence of the Zen Buddhism in the music of Cage is observed when argues that the music composed of melodies has the same value than the sound understood by us like noises. This aspect, among others, infl uenced to Paik, whose video images are defi ned like attributes of traditional works that don’t impress to the audience, but they suggest variable conditions. Some of his works related to Cage’s philosophy have been “Hommage à John Cage” from 1959; “Study for pianoforte” from 1960; and “Global Grove” from 1973, where Paik uses as a collage the images of his avant-garde collaborators John Cage, Allen Ginsberg and Merce Cunningham.

En 1958, el artista coreano Nam June Paik (*1932; †2006 conoce en Alemania a John Cage (*1912; †1992, músico vanguardista, quien estaba profundamente interesado en el budismo zen. Su encuentro con Cage fue vital, ya que el compositor

Maintenance of Segmental Lordosis and Disk Height in Stand-alone and Instrumented Extreme Lateral Interbody Fusion (XLIF).

Science.gov (United States)

Malham, Gregory M; Ellis, Ngaire J; Parker, Rhiannon M; Blecher, Carl M; White, Rohan; Goss, Ben; Seex, Kevin A

2017-03-01

A prospective single-surgeon nonrandomized clinical study. To evaluate the radiographic and clinical outcomes, by fixation type, in extreme lateral interbody fusion (XLIF) patients and provide an algorithm for determining patients suitable for stand-alone XLIF. XLIF may be supplemented with pedicle screw fixation, however, since stabilizing structures remain intact, it is suggested that stand-alone XLIF can be used for certain indications. This eliminates the associated morbidity, though subsidence rates may be elevated, potentially minimizing the clinical benefits. A fixation algorithm was developed after evaluation of patient outcomes from the surgeon's first 30 cases. This algorithm was used prospectively for 40 subsequent patients to determine the requirement for supplemental fixation. Preoperative, postoperative, and 12-month follow-up computed tomography scans were measured for segmental and global lumbar lordosis and posterior disk height. Clinical outcome measures included back and leg pain (visual analogue scale), Oswestry Disability Index (ODI), and SF-36 physical and mental component scores (PCS and MCS). Preoperatively to 12-month follow-up there were increases in segmental lordosis (7.9-9.4 degrees, P=0.0497), lumbar lordosis (48.8-55.2 degrees, P=0.0328), and disk height (3.7-5.5 mm, P=0.0018); there were also improvements in back (58.6%) and leg pain (60.0%), ODI (44.4%), PCS (56.7%), and MCS (16.1%) for stand-alone XLIF. For instrumented XLIF, segmental lordosis (7.6-10.5 degrees, P=0.0120) and disk height (3.5-5.6 mm, Plordosis decreased (51.1-45.8 degrees, P=0.2560). Back (49.8%) and leg pain (30.8%), ODI (32.3%), PCS (37.4%), and MCS (2.0%) were all improved. Subsidence occurred in 3 (7.5%) stand-alone patients. The XLIF treatment fixation algorithm provided a clinical pathway to select suitable patients for stand-alone XLIF. These patients achieved positive clinical outcomes, satisfactory fusion rates, with sustained correction of lordosis and

Evaluation of caged freshwater mussels as an alternative method for environmental effects monitoring (EEM) studies

International Nuclear Information System (INIS)

Martel, Pierre; Kovacs, Tibor; Voss, Ron; Megraw, Stan

2003-01-01

Results from caged mussel experiments agreed with benthic invertebrate surveys, but not with trends observed for fish. - On three occasions between 1998 and 2000, freshwater mussels were collected by divers in Lake Memphremagog during the spring and transplanted to various locations in the St-Francois River (Quebec, Canada). Mussel growth was monitored by comparing total weight and length at the beginning and end of the exposure period. In 1998, mussels were caged for 60 days at 10 stations, including locations receiving treated effluents from three pulp and paper mills. Overall, there was an apparent trend of increased mussel growth from upstream to downstream along the river. However, mussels caged downstream from the effluent discharge of a bleached kraft pulp and paper mill grew more slowly than those caged immediately upstream in the river. In 1999 and 2000, we further investigated the situation in the vicinity of this bleached kraft mill. The measurements again indicated that growth of mussels in the effluent plume from this mill was reduced in comparison to sites upstream. Overall, in terms of growth, the caged mussels responded both positively and negatively to different environmental conditions. Compared with other monitoring approaches used at these sites during the same period, the caged mussel experiment results were consistent with the trends observed with the benthic invertebrate survey but not with the trends observed for fish

Comparison growth of Kappaphycus alvarezii (Rhodophyta, Solieriaceae cultivation in floating cage and longline in Indonesia

Directory of Open Access Journals (Sweden)

Ma’ruf Kasim

2017-05-01

Full Text Available Currently, cultivation using cages for Kappaphycus alvarezii was limited reported before. This study aims to reveal growth of K. alvarezii cultivated in floating cages and longline. The study was conducted in one of cultivation areas in Southeast Sulawesi, Indonesia. Total gross weight, propagule growth rate and specific growth rate were performing in this study. During our field experiment, total gross weight of K. alvarezii after 40 days, from 5 kg was growth to 22.5 ± 1.40 kg and 38.8 ± 1.6 kg on longline and floating cages, respectively. Propagule growth rate after 40 days, from 50 g was 107.8 ± 7.0 g and 152.5 ± 7.9 g during April, and 132.0 ± 8.0 g and 218.8 ± 8.6 g during August, on longline and floating cage, respectively. Specific growth rate of K. alvarezii was high during August, 2.43% day−1 and 3.69% day−1 cultivated in longline and floating cage, respectively. Propagule morphology was white and damage in 40% cultivated by longline and no damage by using floating cage particular in August and September while high dense of herbivorous fish surrounding the experimental sites.

Agricultural wetlands as potential hotspots for mercury bioaccumulation: Experimental evidence using caged fish

Science.gov (United States)

Ackerman, Joshua T.; Eagles-Smith, Collin A.

2010-01-01

Wetlands provide numerous ecosystem services, but also can be sources of methylmercury (MeHg) production and export. Rice agricultural wetlands in particular may be important sites for MeHg bioaccumulation due to their worldwide ubiquity, periodic flooding schedules, and high use by wildlife. We assessed MeHg bioaccumulation within agricultural and perennial wetlands common to California's Central Valley during summer, when the majority of wetland habitats are shallowly flooded rice fields. We introduced caged western mosquitofish (Gambusia affinis) within white rice (Oryza sativa), wild rice (Zizania palustris), and permanent wetlands at water inlets, centers, and outlets. Total mercury (THg) concentrations and body burdens in caged mosquitofish increased rapidly, exceeding baseline values at introduction by 135% to 1197% and 29% to 1566% among sites, respectively, after only 60 days. Mercury bioaccumulation in caged mosquitofish was greater in rice fields than in permanent wetlands, with THg concentrations at wetland outlets increasing by 12.1, 5.8, and 2.9 times over initial concentrations in white rice, wild rice, and permanent wetlands, respectively. In fact, mosquitofish caged at white rice outlets accumulated 721 ng Hg/fish in just 60 days. Mercury in wild mosquito fish and Mississippi silversides (Menidia audens) concurrently sampled at wetland outlets also were greater in white rice and wild rice than permanent wetlands. Within wetlands, THg concentrations and body burdens of both caged and wild fish increased from water inlets to outlets in white rice fields, and tended to not vary among sites in permanent wetlands. Fish THg concentrations in agricultural wetlands were high, exceeding 0.2 ??g/g ww in 82% of caged fish and 59% of wild fish. Our results indicate that shallowly flooded rice fields are potential hotspots for MeHg bioaccumulation and, due to their global prevalence, suggest that agricultural wetlands may be important contributors to Me

Intracage ammonia levels in static and individually ventilated cages housing C57BL/6 mice on 4 bedding substrates.

Science.gov (United States)

Ferrecchia, Christie E; Jensen, Kelly; Van Andel, Roger

2014-03-01

The relationship among ammonia levels, cage-changing frequency, and bedding types is an important and potentially controversial topic in the laboratory animal science community. Some bedding options may not provide sufficient urine absorption and bacterial regulation to minimize ammonia production during the interval between cage changes. High intracage ammonia levels can cause subclinical degeneration and inflammation of nasal passages, rhinitis and olfactory epithelial necrosis in exposed mice. Here we sought to compare the effects of 4 commonly used bedding substrates (1/4-in. irradiated corncob, reclaimed wood pulp, aspen wood chips, and recycled newspaper) on ammonia generation when housing female C57BL/6 mice in static and individually ventilated caging. Intracage ammonia levels were measured daily for 1 wk (static cage experiment) or 2 wk (IVC experiment). The results of this study suggest that the corncob, aspen wood chip, and recycled newspaper beddings that we tested are suitable for once-weekly cage changing for static cages and for changing every 2 wk for IVC. However, ammonia levels were not controlled appropriately in cages containing reclaimed wood pulp bedding, and pathologic changes occurred within 1 wk in the nares of mice housed on this bedding in static cages.

Spiro annulation of cage polycycles via Grignard reaction and ring-closing metathesis as key steps

Directory of Open Access Journals (Sweden)

Sambasivarao Kotha

2015-08-01

Full Text Available A simple synthetic strategy to C2-symmetric bis-spiro-pyrano cage compound 7 involving ring-closing metathesis is reported. The hexacyclic dione 10 was prepared from simple and readily available starting materials such as 1,4-naphthoquinone and cyclopentadiene. The synthesis of an unprecedented octacyclic cage compound through intramolecular Diels–Alder (DA reaction as a key step is described. The structures of three new cage compounds 7, 12 and 18 were confirmed by single crystal X-ray diffraction studies.

Comparison among perfect-C®, zero-P®, and plates with a cage in single-level cervical degenerative disc disease.

Science.gov (United States)

Noh, Sung Hyun; Zhang, Ho Yeol

2018-01-25

We intended to analyze the efficacy of a new integrated cage and plate device called Perfect-C for anterior cervical discectomy and fusion (ACDF) to cure single-level cervical degenerative disc disease. We enrolled 148 patients who were subjected to single-level ACDF with one of the following three surgical devices: a Perfect-C implant (41 patients), a Zero-P implant (36 patients), or a titanium plate with a polyetheretherketone (PEEK) cage (71 patients). We conducted a retrospective study to compare the clinical and radiological results among the three groups. The length of the operation, intraoperative blood loss, and duration of hospitalization were significantly lower in the Perfect-C group than in the Zero-P and plate-with-cage groups (P Zero-P groups but was noted in 21 cases (30%) in the plate-with-cage group. The cephalad and caudal plate-to-disc distance (PDD) and the cephalad and caudal PDD/anterior body height (ABH) were significantly greater in the Perfect-C and Zero-P groups than in the plate-with-cage group (P Zero-P group, and in 15 cases (21%) in the plate-with-cage group. Fusion occurred in 37 cases (90%) in the Perfect-C group, in 31 cases (86%) in the Zero-P group, and in 68 cases (95%) in the plate-with-cage group. The Perfect-C, Zero-P, and plate-with-cage devices are effective for treating single-level cervical degenerative disc disease. However, the Perfect-C implant has many advantages over both the Zero-P implant and conventional plate-cage treatments. The Perfect-C implant was associated with shorter operation times and hospitalization durations, less blood loss, and lower subsidence rates compared with the Zero-P implant or the titanium plate with a PEEK cage.

Suspected Lonely Mouse Syndrome as a Cage Effect in a Drug Safety Study

Directory of Open Access Journals (Sweden)

Xiaobu Ye

2018-01-01

Full Text Available Studies have demonstrated that buprenorphine, a front line drug for veterinary analgesia, may alleviate symptoms of chronic pain. A cage side observation protocol was used to record behavioral signs in a mouse clinical trial of extended release buprenorphine. A retrospective review of the observations for signs of pain and stress revealed that mice given a fivefold overdose of buprenorphine (16.25 mg/kg showed lethargy and facial signs associated with stress. However, similar signs were observed in the drug-free control mice as early as Day 3 of single-cage housing. This appears to be the first report of cage effects in a clinical trial for a veterinary drug.

Synthesis and evaluation of novel caged DNA alkylating agents bearing 3,4-epoxypiperidine structure.

Science.gov (United States)

Kawada, Yuji; Kodama, Tetsuya; Miyashita, Kazuyuki; Imanishi, Takeshi; Obika, Satoshi

2012-07-14

Previously, we reported that the 3,4-epoxypiperidine structure, whose design was based on the active site of DNA alkylating antitumor antibiotics, azinomycins A and B, possesses prominent DNA cleavage activity. In this report, novel caged DNA alkylating agents, which were designed to be activated by UV irradiation, were synthesized by the introduction of four photo-labile protecting groups to a 3,4-epoxypiperidine derivative. The DNA cleavage activity and cytotoxicity of the caged DNA alkylating agents were examined under UV irradiation. Four caged DNA alkylating agents showed various degrees of bioactivity depending on the photosensitivity of the protecting groups.

Influence of the ionic liquid [C4mpy][Tf2N] on the structure of the miniprotein Trp-cage.

Science.gov (United States)

Baker, Joseph L; Furbish, Jeffrey; Lindberg, Gerrick E

2015-11-01

We examine the effect of the ionic liquid [C4mpy][Tf2N] on the structure of the miniprotein Trp-cage and contrast these results with the behavior of Trp-cage in water. We find the ionic liquid has a dramatic effect on Trp-cage, though many similarities with aqueous Trp-cage are observed. We assess Trp-cage folding by monitoring root mean square deviation from the crystallographic structure, radius of gyration, proline cis/trans isomerization state, protein secondary structure, amino acid contact formation and distance, and native and non-native contact formation. Starting from an unfolded configuration, Trp-cage folds in water at 298 K in less than 500 ns of simulation, but has very little mobility in the ionic liquid at the same temperature, which can be ascribed to the higher ionic liquid viscosity. At 365 K, the mobility of the ionic liquid is increased and initial stages of Trp-cage folding are observed, however Trp-cage does not reach the native folded state in 2 μs of simulation in the ionic liquid. Therefore, in addition to conventional molecular dynamics, we also employ scaled molecular dynamics to expedite sampling, and we demonstrate that Trp-cage in the ionic liquid does closely approach the aqueous folded state. Interestingly, while the reduced mobility of the ionic liquid is found to restrict Trp-cage motion, the ionic liquid does facilitate proline cis/trans isomerization events that are not seen in our aqueous simulations. Copyright © 2015 Elsevier Inc. All rights reserved.

Dimensional study of the caging order parameter at the glass transition.

Science.gov (United States)

Charbonneau, Patrick; Ikeda, Atsushi; Parisi, Giorgio; Zamponi, Francesco

2012-08-28

The glass problem is notoriously hard and controversial. Even at the mean-field level, little is agreed upon regarding why a fluid becomes sluggish while exhibiting but unremarkable structural changes. It is clear, however, that the process involves self-caging, which provides an order parameter for the transition. It is also broadly assumed that this cage should have a gaussian shape in the mean-field limit. Here we show that this ansatz does not hold. By performing simulations as a function of spatial dimension d, we find the cage to keep a nontrivial form. Quantitative mean-field descriptions of the glass transition, such as mode-coupling theory, density functional theory, and replica theory, all miss this crucial element. Although the mean-field random first-order transition scenario of the glass transition is qualitatively supported here and non-mean-field corrections are found to remain small on decreasing d, reconsideration of its implementation is needed for it to result in a coherent description of experimental observations.

Investigation of different cage designs and mechano-regulation algorithms in the lumbar interbody fusion process - a finite element analysis.

Science.gov (United States)

Postigo, Sergio; Schmidt, Hendrik; Rohlmann, Antonius; Putzier, Michael; Simón, Antonio; Duda, Georg; Checa, Sara

2014-04-11

Lumbar interbody fusion cages are commonly used to treat painful spinal degeneration and instability by achieving bony fusion. Many different cage designs exist, however the effect of cage morphology and material properties on the fusion process remains largely unknown. This finite element model study aims to investigate the influence of different cage designs on bone fusion using two mechano-regulation algorithms of tissue formation. It could be observed that different cages play a distinct key role in the mechanical conditions within the fusion region and therefore regulate the time course of the fusion process. Copyright © 2014 Elsevier Ltd. All rights reserved.

Control strategy of wind turbine based on permanent magnet synchronous generator and energy storage for stand-alone systems

DEFF Research Database (Denmark)

Deng, Fujin; Liu, Dong; Chen, Zhe

2017-01-01

This paper investigates a variable speed wind turbine based on permanent magnet synchronous generator and a full-scale power converter in a stand-alone system. An energy storage system(ESS) including battery and fuel cell-electrolyzer combination is connected to the DC link of the full-scale power...... converter through the power electronics interface. Wind is the primary power source of the system, the battery and FC-electrolyzer combination is used as a backup and a long-term storage system to provide or absorb power in the stand-alone system, respectively. In this paper, a control strategy is proposed...... for the operation of this variable speed wind turbine in a stand-alone system, where the generator-side converter and the ESS operate together to meet the demand of the loads. This control strategy is competent for supporting the variation of the loads or wind speed and limiting the DC-link voltage of the full...

Standard methods for maintaining adult Apis mellifera in cages under in vitro laboratory conditions

NARCIS (Netherlands)

Williams, G.R.; Alaux, C.; Costa, C.; Csaki, C.; Steen, van der J.J.M.

2013-01-01

Adult honey bees are maintained in vitro in laboratory cages for a variety of purposes. For example, researchers may wish to perform experiments on honey bees caged individually or in groups to study aspects of parasitology, toxicology, or physiology under highly controlled conditions, or they may

Final Report for DUSEL R&D: BetaCage: A Screener of Ultra-Low-Level Radioactive Surface Contamination

Energy Technology Data Exchange (ETDEWEB)

Golwala, Sunil R. [California Institute of Technology

2013-12-20

The eventual full-size, radiopure BetaCage will be a low-background, atmospheric-pressure neon drift chamber with unprecedented sensitivity to emitters of low-energy electrons and alpha particles. We expect that the prototype BetaCage already developed will be an excellent screener of alpha particles. Both the prototype and final BetaCage will provide new infrastructure for rare-event science.

The Crystal Structure of a Maxi/Mini-Ferritin Chimera Reveals Guiding Principles for the Assembly of Protein Cages

Energy Technology Data Exchange (ETDEWEB)

Cornell, Thomas A. [Department; Division; Srivastava, Yogesh [Genome; Jauch, Ralf [Genome Institute of Singapore, Singapore; Genome; Fan, Rongli [Division; Orner, Brendan P. [Department; Division

2017-07-19

Cage proteins assemble into nanoscale structures with large central cavities. They play roles, including those as virus capsids and chaperones, and have been applied to drug delivery and nanomaterials. Furthermore, protein cages have been used as model systems to understand and design protein quaternary structure. Ferritins are ubiquitous protein cages that manage iron homeostasis and oxidative damage. Two ferritin subfamilies have strongly similar tertiary structure yet distinct quaternary structure: maxi-ferritins normally assemble into 24-meric, octahedral cages with C-terminal E-helices centered around 4-fold symmetry axes, and mini-ferritins are 12-meric, tetrahedral cages with 3-fold axes defined by C-termini lacking E-domains. To understand the role E-domains play in ferritin quaternary structure, we previously designed a chimera of a maxi-ferritin E-domain fused to the C-terminus of a mini-ferritin. The chimera is a 12-mer cage midway in size between those of the maxi- and mini-ferritin. The research described herein sets out to understand (a) whether the increase in size over a typical mini-ferritin is due to a frozen state where the E-domain is flipped out of the cage and (b) whether the symmetrical preference of the E-domain in the maxi-ferritin (4-fold axis) overrules the C-terminal preference in the mini-ferritin (3-fold axis). With a 1.99 Å resolution crystal structure, we determined that the chimera assembles into a tetrahedral cage that can be nearly superimposed with the parent mini-ferritin, and that the E-domains are flipped external to the cage at the 3-fold symmetry axes.

Assessment of geothermal assisted coal-fired power generation using an Australian case study

Energy Technology Data Exchange (ETDEWEB)

Zhou, Cheng [Priority Research Centre for Energy, Discipline of Chemical Engineering, School of Engineering, Faculty of Engineering and Built Environment, The University of Newcastle, Callaghan, NSW 2308 (Australia); Doroodchi, Elham [Priority Research Centre for Advanced Particle Processing and Transport, Discipline of Chemical Engineering, School of Engineering, Faculty of Engineering and Built Environment, The University of Newcastle, Callaghan, NSW 2308 (Australia); Moghtaderi, Behdad [Priority Research Centre for Energy, Discipline of Chemical Engineering, School of Engineering, Faculty of Engineering and Built Environment, The University of Newcastle, Callaghan, NSW 2308 (Australia)

2014-06-01

Highlights: • Systematic techno-economic analyses of GAPG system completed for Australian conditions. • Greater utilisation efficiency of both geothermal and fossil fuel resources was achieved. • Reference maps developed to predict conditions when hybrid plant outperforms two stand-alone plants. • Carbon tax and RECs rates of 40 $/tonne and 60 cents/kW h are adequate. • HDR resources should be located no further than 20 km from the plant. - Abstract: A systematic techno-economic analysis of geothermal assisted power generation (GAPG) was performed for a 500 MW unit of a typical coal-fired power plant located at the upper Hunter region of New South Wales, Australia. Specifically, the GAPG viability and performance was examined by investigating the impacts of reservoir temperature, resource distance, hybridisation scheme, and economic conditions including carbon tax and Renewable Energy Certificates (REC). The process simulation package, Aspen HYSYS, was employed for all simulation purposes. Thermodynamically, GAPG system was found to increase the power output of the plant by up to 19% under the booster mode whilst in fuel saving mode the coal consumption reduced by up to 0.3 million tonne/year decreasing the Green House Gas (GHG) emission by up to 15% (0.6 million tonne/year). Economic analyses showed that for a typical HDR resource with a reservoir temperature about 150 °C located within a 5 km radius from the power plant, the GAPG system becomes economically competitive to the stand-alone fossil fuel based plant when minimum carbon tax and RECs rates of 40 $/tonne and 60 cents/kW h are introduced. The figure of merit analyses comparing GAPG system with both stand-alone fossil fuel and stand-alone geothermal plants showed that an economically feasible GAPG system requires the use of HDR resources located no further than 20 km from the plants. Reference maps were also developed to predict suitable conditions for which the hybrid plant outperforms the

Assessment of geothermal assisted coal-fired power generation using an Australian case study

International Nuclear Information System (INIS)

Zhou, Cheng; Doroodchi, Elham; Moghtaderi, Behdad

2014-01-01

Highlights: • Systematic techno-economic analyses of GAPG system completed for Australian conditions. • Greater utilisation efficiency of both geothermal and fossil fuel resources was achieved. • Reference maps developed to predict conditions when hybrid plant outperforms two stand-alone plants. • Carbon tax and RECs rates of 40 $/tonne and 60 cents/kW h are adequate. • HDR resources should be located no further than 20 km from the plant. - Abstract: A systematic techno-economic analysis of geothermal assisted power generation (GAPG) was performed for a 500 MW unit of a typical coal-fired power plant located at the upper Hunter region of New South Wales, Australia. Specifically, the GAPG viability and performance was examined by investigating the impacts of reservoir temperature, resource distance, hybridisation scheme, and economic conditions including carbon tax and Renewable Energy Certificates (REC). The process simulation package, Aspen HYSYS, was employed for all simulation purposes. Thermodynamically, GAPG system was found to increase the power output of the plant by up to 19% under the booster mode whilst in fuel saving mode the coal consumption reduced by up to 0.3 million tonne/year decreasing the Green House Gas (GHG) emission by up to 15% (0.6 million tonne/year). Economic analyses showed that for a typical HDR resource with a reservoir temperature about 150 °C located within a 5 km radius from the power plant, the GAPG system becomes economically competitive to the stand-alone fossil fuel based plant when minimum carbon tax and RECs rates of 40 $/tonne and 60 cents/kW h are introduced. The figure of merit analyses comparing GAPG system with both stand-alone fossil fuel and stand-alone geothermal plants showed that an economically feasible GAPG system requires the use of HDR resources located no further than 20 km from the plants. Reference maps were also developed to predict suitable conditions for which the hybrid plant outperforms the

Use of Super-Capacitor to Enhance Charging Performance of Stand-Alone Solar PV System

KAUST Repository

Huang, B. J.; Hsu, P. C.; Ho, P. Y

2011-01-01

Introduction: The battery charging performance in a stand-alone solar PV system affects the PV system efficiency and the load operating time. The New Energy Center of National Taiwan University has been devoted to the development of a PWM charging

Cage for shield-type support. Schildausbaugestell

Energy Technology Data Exchange (ETDEWEB)

Harryers, W; Blumenthal, G; Irresberger, H

1981-08-13

A cage for shield-type support containing a fracture shield supported by a hydraulic stamp and a projecting roof bar was constructed in such a way that no cellular shirt is needed to timber the caved room. The roof bar which is linked at a joint axis at the face-side end of the fracture shield is formed at the face side as a multiply foldable bar. (HGOE).

The BetaCage: Ultrasensitive Screener for Radioactive Backgrounds

Science.gov (United States)

Thompson, Michael; BetaCage Collaboration

2017-09-01

Rare event searches, such as dark matter detection and neutrinoless double beta decay, require screening of materials for backgrounds such as beta emission and alpha decaying isotopes. The BetaCage is a proposed ultra-sensitive time-projection chamber to screen for alpha-emitting and low energy beta-emitting (10-200 keV) contaminants. The expected sensitivity is 0.1 beta particles (perkeV -m2 - day) and 0.1 alpha particles (perm2 - day) , where the former will be limited by Compton scattering of external photons in the screening samples and the latter is expected to be signal-limited. The prototype BetaCage under commissioning at South Dakota School of Mines & Technology is filled with P10 gas (10% methane, 90% argon) in place of neon and is 40×40×20 cm in size. Details on design, construction and characterization will be presented.

Modelling of current loads on aquaculture net cages

Science.gov (United States)

Kristiansen, Trygve; Faltinsen, Odd M.

2012-10-01

In this paper we propose and discuss a screen type of force model for the viscous hydrodynamic load on nets. The screen model assumes that the net is divided into a number of flat net panels, or screens. It may thus be applied to any kind of net geometry. In this paper we focus on circular net cages for fish farms. The net structure itself is modelled by an existing truss model. The net shape is solved for in a time-stepping procedure that involves solving a linear system of equations for the unknown tensions at each time step. We present comparisons to experiments with circular net cages in steady current, and discuss the sensitivity of the numerical results to a set of chosen parameters. Satisfactory agreement between experimental and numerical prediction of drag and lift as function of the solidity ratio of the net and the current velocity is documented.

Bulletproof Love : Luke Cage (2016 and Religion

Directory of Open Access Journals (Sweden)

Derry, Ken

2017-05-01

Full Text Available There are many ways to think about religion and popular culture. One method is to ask where and when we see what might be commonly understood as “religious tradition(s” explicitly on display. Another is to think about superhero narratives themselves as “religious”, using this term as a conceptual tool for categorizing and thereby better understanding particular dimensions of human experience. This article takes a variety of approaches to understanding religion in relation to the recent television series LUKE CAGE (Netflix, US 2016. These approaches take their hermeneutical cues from a range of disciplines, including studies of the Bible; Hip Hop; gender; Black Theology; African American religion; and philosophy. The results of this analysis highlight the polysemic nature of popular culture in general, and of superhero stories in particular. Like religious traditions themselves, the show is complex and contradictory: it is both progressive and reactionary; emphasizes community and valorizes an individual; critiques and endorses Christianity; subverts and promotes violence. Depending on the questions asked, LUKE CAGE (2016 provides a range of very different answers.

1/f Noise Inside a Faraday Cage

Science.gov (United States)

Handel, Peter H.; George, Thomas F.

2009-04-01

We show that quantum 1/f noise does not have a lower frequency limit given by the lowest free electromagnetic field mode in a Faraday cage, even in an ideal cage. Indeed, quantum 1/f noise comes from the infrared-divergent coupling of the field with the charges, in their joint nonlinear system, where the charges cause the field that reacts back on the charges, and so on. This low-frequency limitation is thus not applicable for the nonlinear system of matter and field in interaction. Indeed, this nonlinear system is governed by Newton's laws, Maxwell's equations, in general also by the diffusion equations for particles and heat, or reaction kinetics given by quantum matrix elements. Nevertheless, all the other quantities can be eliminated in principle, resulting in highly nonlinear integro-differential equations for the electromagnetic field only, which no longer yield a fundamental frequency. Alternatively, we may describe this through the presence of an infinite system of subharmonics. We show how this was proven early in the classical and quantum domains, adding new insight.

1/f Noise Inside a Faraday Cage

International Nuclear Information System (INIS)

Handel, Peter H.; George, Thomas F.

2009-01-01

We show that quantum 1/f noise does not have a lower frequency limit given by the lowest free electromagnetic field mode in a Faraday cage, even in an ideal cage. Indeed, quantum 1/f noise comes from the infrared-divergent coupling of the field with the charges, in their joint nonlinear system, where the charges cause the field that reacts back on the charges, and so on. This low-frequency limitation is thus not applicable for the nonlinear system of matter and field in interaction. Indeed, this nonlinear system is governed by Newton's laws, Maxwell's equations, in general also by the diffusion equations for particles and heat, or reaction kinetics given by quantum matrix elements. Nevertheless, all the other quantities can be eliminated in principle, resulting in highly nonlinear integro-differential equations for the electromagnetic field only, which no longer yield a fundamental frequency. Alternatively, we may describe this through the presence of an infinite system of subharmonics. We show how this was proven early in the classical and quantum domains, adding new insight.

Evaluation of Two Compressed Air Foam Systems for Culling Caged Layer Hens

Science.gov (United States)

Weiher, Jaclyn A.; Alphin, Robert L.; Hougentogler, Daniel P.

2018-01-01

Simple Summary Control of avian influenza and similar diseases in commercial poultry operations is challenging; the six major steps are surveillance, biosecurity, quarantine, depopulation, disposal, and cleaning and disinfection. Depopulation is used to cull animals that are terminally ill and to reduce the number of animals that can spread an untreatable disease. Water-based foam depopulation was used effectively during the 2014–2015 highly pathogenic avian influenza outbreak in the United States. Water-based foam, however, cannot be used effectively in caged poultry operations. Compressed air foam systems were initially developed for structural fire-fighting and, with modifications, can provide the conditions required to effectively penetrate a poultry cage and provide sufficient residence time for depopulation. In this experiment, compressed air foam was used to depopulate caged layer hens. Compressed air foam resulted in faster unconsciousness than carbon dioxide gassing. The experiment demonstrated that compressed air foam systems have promise for depopulating birds raised in cages. Abstract Outbreaks of avian influenza (AI) and other highly contagious poultry diseases continue to be a concern for those involved in the poultry industry. In the situation of an outbreak, emergency depopulation of the birds involved is necessary. In this project, two compressed air foam systems (CAFS) were evaluated for mass emergency depopulation of layer hens in a manure belt equipped cage system. In both experiments, a randomized block design was used with multiple commercial layer hens treated with one of three randomly selected depopulation methods: CAFS, CAFS with CO2 gas, and CO2 gas. In Experiment 1, a Rowe manufactured CAFS was used, a selection of birds were instrumented, and the time to unconsciousness, brain death, altered terminal cardiac activity and motion cessation were recorded. CAFS with and without CO2 was faster to unconsciousness, however, the other

A cage position monitor based on magnetically striped rope

Energy Technology Data Exchange (ETDEWEB)

Thomas, V M

1978-01-01

Following the winding disaster at Markham Colliery in July 1973 recommendations to monitor the position of the cage directly at all times throughout the winding cycle, and to provide a system of communication with persons in the conveyance were made. The system adopted by MRDE was the 'magnetically striped rope'. An experimental system was installed at Maltby Colliery, South Yorkshire, and has been working successfully for well over a year. Magnetic marking of a hoist or guide rope can be carried out using permanent magnets but a much more convenient method has been devised using a pulsed electromagnet sliding on the rope. Detection is achieved by two static magnetic sensors spaced to give quadrature output. By processing the signals and using an up/down counter it is possible to sense the direction of movement and the distance travelled by the cage from a given datum. The information can be further processed to indicate velocity, overspeed and overwind, and when referenced to drum revolutions may be used to monitor rope slip in friction winders or slack rope in drum winders. When the guide rope is magnetically marked and sensed, the information must be transmitted from the cage to the surface. Such a data communication link, developed by MRDE, also provides a base for a general shaft communication system.

Fuzzy logic control of stand-alone photovoltaic system with battery storage

Science.gov (United States)

Lalouni, S.; Rekioua, D.; Rekioua, T.; Matagne, E.

Photovoltaic energy has nowadays an increased importance in electrical power applications, since it is considered as an essentially inexhaustible and broadly available energy resource. However, the output power provided via the photovoltaic conversion process depends on solar irradiation and temperature. Therefore, to maximize the efficiency of the photovoltaic energy system, it is necessary to track the maximum power point of the PV array. The present paper proposes a maximum power point tracker (MPPT) method, based on fuzzy logic controller (FLC), applied to a stand-alone photovoltaic system. It uses a sampling measure of the PV array power and voltage then determines an optimal increment required to have the optimal operating voltage which permits maximum power tracking. This method carries high accuracy around the optimum point when compared to the conventional one. The stand-alone photovoltaic system used in this paper includes two bi-directional DC/DC converters and a lead-acid battery bank to overcome the scare periods. One converter works as an MPP tracker, while the other regulates the batteries state of charge and compensates the power deficit to provide a continuous delivery of energy to the load. The Obtained simulation results show the effectiveness of the proposed fuzzy logic controller.

Effect of nest design, passages, and hybrid on use of nest and production performance of layers in furnished cages.

Science.gov (United States)

Wall, H; Tauson, R; Elwinger, K

2002-03-01

Production performance, including egg quality, and proportion of eggs laid in nests were studied in furnished experimental cages incorporating nests, litter baths, and perches. The study comprised a total of 972 hens of two genotypes: Lohmann Selected Leghorn (LSL) and Hy-Line White. The birds were studied from 20 to 80 wk of age, and conventional four-hen cages were included as a reference. In furnished cages for six hens, the effects of 30 or 50% vs. 100% nest bottom lining (Astro turf) were studied with LSL hens. Nest bottom lining had no significant effect on egg production or proportions of cracked or dirty eggs, but the use of nests was significantly higher in cages incorporating nests with 100% lining, compared with 50 or 30%. The two hybrids were compared when housed in large, group-furnished cages for 14 or 16 hens of two designs; with a rear partition with two pop holes or fully open, i.e., no rear partition. LSL birds produced significantly better and had a significantly lower proportion of cracked eggs. There was no difference between H- and O-cages, either in production or in egg quality. LSL birds laid a significantly lower proportion of eggs in the nests, especially in O-cages, implying a significant hybrid x cage interaction. When housed in conventional cages, the hybrids did not differ in proportion of cracked eggs but differed in production traits. It was concluded that with the present nest design, the proportion of nest bottom lining cannot be reduced without affecting birds' use of nests, but the proportion did not affect exterior egg quality. The effect of genotype should be considered in the further development of furnished cages.

Methanol production via pressurized entrained flow biomass gasification – Techno-economic comparison of integrated vs. stand-alone production

International Nuclear Information System (INIS)

Andersson, Jim; Lundgren, Joakim; Marklund, Magnus

2014-01-01

The main objective with this work was to investigate techno-economically the opportunity for integrated gasification-based biomass-to-methanol production in an existing chemical pulp and paper mill. Three different system configurations using the pressurized entrained flow biomass gasification (PEBG) technology were studied, one stand-alone plant, one where the bark boiler in the mill was replaced by a PEBG unit and one with a co-integration of a black liquor gasifier operated in parallel with a PEBG unit. The cases were analysed in terms of overall energy efficiency (calculated as electricity-equivalents) and process economics. The economics was assessed under the current as well as possible future energy market conditions. An economic policy support was found to be necessary to make the methanol production competitive under all market scenarios. In a future energy market, integrating a PEBG unit to replace the bark boiler was the most beneficial case from an economic point of view. In this case the methanol production cost was reduced in the range of 11–18 Euro per MWh compared to the stand-alone case. The overall plant efficiency increased approximately 7%-units compared to the original operation of the mill and the non-integrated stand-alone case. In the case with co-integration of the two parallel gasifiers, an equal increase of the system efficiency was achieved, but the economic benefit was not as apparent. Under similar conditions as the current market and when methanol was sold to replace fossil gasoline, co-integration of the two parallel gasifiers was the best alternative based on received IRR. - Highlights: • Techno-economic results regarding integration of methanol synthesis processes in a pulp and paper mill are presented. • The overall energy efficiency increases in integrated methanol production systems compared to stand-alone production units. • The economics of the integrated system improves compared to stand-alone alternatives. • Tax

Assessment of renewable energy resources potential for large scale and standalone applications in Ethiopia

NARCIS (Netherlands)

Tucho, Gudina Terefe; Weesie, Peter D.M.; Nonhebel, Sanderine

2014-01-01

This study aims to determine the contribution of renewable energy to large scale and standalone application in Ethiopia. The assessment starts by determining the present energy system and the available potentials. Subsequently, the contribution of the available potentials for large scale and

The effects of individually ventilated cages on the respiratory systems of male and female Wistar rats from birth until adulthood

Directory of Open Access Journals (Sweden)

Guilherme D’Aprile Marchesi

Full Text Available OBJECTIVE: To evaluate the respiratory systems of male and female rats maintained in individually ventilated cages (IVCs from birth until adulthood. METHODS: Female Wistar rats were housed in individually ventilated cages or conventional cages (CCs and mated with male Wistar rats. After birth and weaning, the male offspring were separated from the females and kept in cages of the same type until 12 weeks of age. RESULTS: The level of food consumption was lower in male offspring (IVC=171.7±9; CC=193.1±20 than in female offspring (IVC=100.6±7; CC=123.4±0.4, whereas the water intake was higher in female offspring (IVC=149.8±11; CC=99.2±0 than in male offspring (IVC=302.5±25; CC=249.7±22 at 11 weeks of age when housed in IVCs. The cage temperature was higher in individually ventilated cages than in conventional cages for both male (IVCs=25.9±0.5; CCs=22.95±0.3 and female (IVCs=26.2±0.3; CCs=23.1±0.3 offspring. The respiratory resistance (IVC=68.8±2.8; CC=50.6±3.0 and elastance (IVC=42.0±3.9; CC=32.4±2.0 at 300 µm/kg were higher in the female offspring housed in ventilated cages. The ciliary beat values were lower in both the male (IVCs=13.4±0.2; CC=15±0.4 and female (IVC=13.5±0.4; CC=15.9±0.6 offspring housed in individually ventilated cages than in those housed in conventional cages. The total cell (IVC=117.5±9.7; CC=285.0±22.8, neutrophil (IVC=13.1±4.8; CC=75.6±4.1 and macrophage (IVC=95.2±11.8; CC=170.0±18.8 counts in the bronchoalveolar lavage fluid were lower in the female offspring housed in individually ventilated cages than in those housed in conventional cages. CONCLUSIONS: The environmental conditions that exist in individually ventilated cages should be considered when interpreting the results of studies involving laboratory animals. In this study, we observed gender dimorphism in both the water consumption and respiratory mechanics of rats kept in ventilated cages.

The effects of individually ventilated cages on the respiratory systems of male and female Wistar rats from birth until adulthood

Science.gov (United States)

Marchesi, Guilherme D’Aprile; de Fatima Soto, Sônia; de Castro, Isac; Rodrigues, Thiago Guimarães; Moriya, Henrique Takachi; de Almeida, Francine Maria; Pazetti, Rogerio; Heimann, Joel Claudio; Furukawa, Luzia Naôko Shinohara

2017-01-01

OBJECTIVE: To evaluate the respiratory systems of male and female rats maintained in individually ventilated cages (IVCs) from birth until adulthood. METHODS: Female Wistar rats were housed in individually ventilated cages or conventional cages (CCs) and mated with male Wistar rats. After birth and weaning, the male offspring were separated from the females and kept in cages of the same type until 12 weeks of age. RESULTS: The level of food consumption was lower in male offspring (IVC=171.7±9; CC=193.1±20) than in female offspring (IVC=100.6±7; CC=123.4±0.4), whereas the water intake was higher in female offspring (IVC=149.8±11; CC=99.2±0) than in male offspring (IVC=302.5±25; CC=249.7±22) at 11 weeks of age when housed in IVCs. The cage temperature was higher in individually ventilated cages than in conventional cages for both male (IVCs=25.9±0.5; CCs=22.95±0.3) and female (IVCs=26.2±0.3; CCs=23.1±0.3) offspring. The respiratory resistance (IVC=68.8±2.8; CC=50.6±3.0) and elastance (IVC=42.0±3.9; CC=32.4±2.0) at 300 µm/kg were higher in the female offspring housed in ventilated cages. The ciliary beat values were lower in both the male (IVCs=13.4±0.2; CC=15±0.4) and female (IVC=13.5±0.4; CC=15.9±0.6) offspring housed in individually ventilated cages than in those housed in conventional cages. The total cell (IVC=117.5±9.7; CC=285.0±22.8), neutrophil (IVC=13.1±4.8; CC=75.6±4.1) and macrophage (IVC=95.2±11.8; CC=170.0±18.8) counts in the bronchoalveolar lavage fluid were lower in the female offspring housed in individually ventilated cages than in those housed in conventional cages. CONCLUSIONS: The environmental conditions that exist in individually ventilated cages should be considered when interpreting the results of studies involving laboratory animals. In this study, we observed gender dimorphism in both the water consumption and respiratory mechanics of rats kept in ventilated cages. PMID:28355363

Sagittal Plane Correction Using the Lateral Transpsoas Approach: A Biomechanical Study on the Effect of Cage Angle and Surgical Technique on Segmental Lordosis.

Science.gov (United States)

Melikian, Rojeh; Yoon, Sangwook Tim; Kim, Jin Young; Park, Kun Young; Yoon, Caroline; Hutton, William

2016-09-01

Cadaveric biomechanical study. To determine the degree of segmental correction that can be achieved through lateral transpsoas approach by varying cage angle and adding anterior longitudinal ligament (ALL) release and posterior element resection. Lordotic cage insertion through the lateral transpsoas approach is being used increasingly for restoration of sagittal alignment. However, the degree of correction achieved by varying cage angle and ALL release and posterior element resection is not well defined. Thirteen lumbar motion segments between L1 and L5 were dissected into single motion segments. Segmental angles and disk heights were measured under both 50 N and 500 N compressive loads under the following conditions: intact specimen, discectomy (collapsed disk simulation), insertion of parallel cage, 10° cage, 30° cage with ALL release, 30° cage with ALL release and spinous process (SP) resection, 30° cage with ALL release, SP resection, facetectomy, and compression with pedicle screws. Segmental lordosis was not increased by either parallel or 10° cages as compared with intact disks, and contributed small amounts of lordosis when compared with the collapsed disk condition. Placement of 30° cages with ALL release increased segmental lordosis by 10.5°. Adding SP resection increased lordosis to 12.4°. Facetectomy and compression with pedicle screws further increased lordosis to approximately 26°. No interventions resulted in a decrease in either anterior or posterior disk height. Insertion of a parallel or 10° cage has little effect on lordosis. A 30° cage insertion with ALL release resulted in a modest increase in lordosis (10.5°). The addition of SP resection and facetectomy was needed to obtain a larger amount of correction (26°). None of the cages, including the 30° lordotic cage, caused a decrease in posterior disk height suggesting hyperlordotic cages do not cause foraminal stenosis. N/A.

Design Concepts of Polycarbonate-Based Intervertebral Lumbar Cages: Finite Element Analysis and Compression Testing

Directory of Open Access Journals (Sweden)

J. Obedt Figueroa-Cavazos

2016-01-01

Full Text Available This work explores the viability of 3D printed intervertebral lumbar cages based on biocompatible polycarbonate (PC-ISO® material. Several design concepts are proposed for the generation of patient-specific intervertebral lumbar cages. The 3D printed material achieved compressive yield strength of 55 MPa under a specific combination of manufacturing parameters. The literature recommends a reference load of 4,000 N for design of intervertebral lumbar cages. Under compression testing conditions, the proposed design concepts withstand between 7,500 and 10,000 N of load before showing yielding. Although some stress concentration regions were found during analysis, the overall viability of the proposed design concepts was validated.

ASERA: A Spectrum Eye Recognition Assistant

Science.gov (United States)

Yuan, Hailong; Zhang, Haotong; Zhang, Yanxia; Lei, Yajuan; Dong, Yiqiao; Zhao, Yongheng

2018-04-01

ASERA, ASpectrum Eye Recognition Assistant, aids in quasar spectral recognition and redshift measurement and can also be used to recognize various types of spectra of stars, galaxies and AGNs (Active Galactic Nucleus). This interactive software allows users to visualize observed spectra, superimpose template spectra from the Sloan Digital Sky Survey (SDSS), and interactively access related spectral line information. ASERA is an efficient and user-friendly semi-automated toolkit for the accurate classification of spectra observed by LAMOST (the Large Sky Area Multi-object Fiber Spectroscopic Telescope) and is available as a standalone Java application and as a Java applet. The software offers several functions, including wavelength and flux scale settings, zoom in and out, redshift estimation, and spectral line identification.

[Detection of alcoholism in the medical office: applicability of the CAGE questionnaire by the practicing physician. Group of Medical Practitioners PMU].

Science.gov (United States)

Perdrix, A; Decrey, H; Pécoud, A; Burnand, B; Yersin, B

1995-09-23

The general practitioner (GP) plays a very important role in early detection of alcoholism. Clinical evaluation is often the only method used, although it has been suggested that any systematic patient history should include the CAGE test. We compare the effectiveness of these two approaches and attempt to determine the applicability of the CAGE test in a general practitioner's usual practice. 12 GPs took part in this study during 6 months. They looked for possible alcohol abuse in each new patient by a standard patient history and clinical examination. Patients were randomized into 2 groups, one of which was given the CAGE test and the other not. For each patient in the CAGE group the applicability of the test was quantified by the GP. 416 patients were included; 214 were randomized into the "CAGE group" and 202 into the control group. On a clinical basis, 15 patients in the control group and 16 in the "CAGE group" (14 men, 2 women) were suspected of alcohol abuse. The CAGE test was positive in 15 patients (7%); among these, 6 were not suspect on a clinical basis. In patients aged 18-34, the detection rate of alcohol-related problems more than doubled when the CAGE test was used. The age of the patients influenced performance of the CAGE test and clinical evaluation. Only 2% of women had a positive CAGE test. Administration of the CAGE test was considered easy in 112 patients and average to difficult in 50, while the test was inapplicable with 52 patients. The latter proportion was higher than that observed in institutions (hospitals, outpatient departments) of the same region. Applicability was influenced neither by the sex nor the age of the patients, but varied greatly according to the physician (from 38% to 100%). The CAGE test increases the number of patients detected with alcohol problems by 37% and seems to be especially useful when administered to young people. The number of women with alcohol problems is probably underestimated by both clinical evaluation

CAGE IIIA Distributed Simulation Design Methodology

Science.gov (United States)

2014-05-01

2 VHF Very High Frequency VLC Video LAN Codec – an Open-source cross-platform multimedia player and framework VM Virtual Machine VOIP Voice Over...Implementing Defence Experimentation (GUIDEx). The key challenges for this methodology are with understanding how to: • design it o define the...operation and to be available in the other nation’s simulations. The challenge for the CAGE campaign of experiments is to continue to build upon this

Coordination Control Strategy for AC/DC Hybrid Microgrids in Stand-Alone Mode

Directory of Open Access Journals (Sweden)

Dwi Riana Aryani

2016-06-01

Full Text Available Interest in DC microgrids is rapidly increasing along with the improvement of DC power technology because of its advantages. To support the integration process of DC microgrids with the existing AC utility grids, the form of hybrid AC/DC microgrids is considered for higher power conversion efficiency, lower component cost and better power quality. In the system, AC and DC portions are connected through interlink bidirectional AC/DC converters (IC with a proper control system and power management. In the stand-alone operation mode of AC/DC hybrid microgrids, the control of power injection through the IC is crucial in order to maintain the system security. This paper mainly deals with a coordination control strategy of IC and a battery energy storage system (BESS converter under stand-alone operation. A coordinated control strategy for the IC, which considers the state of charge (SOC level of BESS and the load shedding scheme as the last resort, is proposed to obtain better power sharing between AC and DC subgrids. The scheme will be tested with a hybrid AC/DC microgrid, using the tool of the PSCAD/EMTDC software.

Design and synthesis of novel bis-annulated caged polycycles via ring-closing metathesis: pushpakenediol

Directory of Open Access Journals (Sweden)

Sambasivarao Kotha

2014-11-01

Full Text Available Intricate caged molecular frameworks are assembled by an atom economical process via a Diels–Alder (DA reaction, a Claisen rearrangement, a ring-closing metathesis (RCM and an alkenyl Grignard addition. The introduction of olefinic moieties in the pentacycloundecane (PCUD framework at appropriate positions followed by RCM led to the formation of novel heptacyclic cage systems.

Using Finite Element Method to Estimate the Material Properties of a Bearing Cage

Science.gov (United States)

2018-02-01

result, a novel approach was developed to empirically test the phenolic cage and to determine the respective elastic and failure material properties...was available. As a result, a novel approach was developed to empirically test the phenolic cage and to determine the respective elastic and...was defeatured to decrease computing time, and the tooling was made rigid. The elements employed were 8-node brick elements with reduced integrations

Porous concrete block as an environmental enrichment device increases activity of laying hens in cages.

Science.gov (United States)

Holcman, A; Gorjanc, G; Stuhec, I

2008-09-01

The purpose of this study was to consider the influence of simple and cheap environmental enrichment such as porous concrete on the behavior of laying hens in conventional cages. Forty brown laying hens were housed in individual wire mesh cages: 20 in experimental cages with porous concrete block provided for pecking and 20 in a control group without concrete block provided. Porous concrete block (5 cm length x 5 cm width x 5 cm height) was mounted on the side wall at the height of the hen's head. Behavior was studied from 42 to 48 wk of age. A group of 8 hens was filmed for 24 h, and the camera was moved each day so that all 40 hens were recorded over 5 d each wk. Videotaping was performed in wk 1, 3, 5, and 7 of the experiment. States (long-term behavior) were observed with 5-min interval recording (feeding, preening, resting, and remaining inactive), whereas events (short-term activities) were observed with instantaneous recording (drinking, pecking concrete, pecking neighbors, pecking cage, and attempting to escape). Data were analyzed with generalized linear mixed model with binomial distribution for states, and Poisson distribution for events. Monte Carlo Markov Chain methods were used to estimate model parameters. Because posterior distributions of quantities of interest were skewed, medians and standard errors are reported. Hens in experimental cages were more active in long-term behavior than controls (64.9 +/- 1.9 and 59.3 +/- 1.9% of the light period, respectively). Correspondingly, hens in the control group showed more long-term inactivity. In addition to pecking the porous concrete block, hens in experimental cages also showed other short-term activities with greater frequency (4.10 +/- 0.31 and 3.51 +/- 0.25 events per h, respectively). Our hypothesis that hens in enriched cages would have a greater level of activity was confirmed. Provision of a piece of porous concrete block as a pecking substrate enriched the environment of the birds at negligible

Co-Pt nanoparticles encapsulated in carbon cages prepared by sonoelectrodeposition

Energy Technology Data Exchange (ETDEWEB)

Luong, Nguyen Hoang; Hai, Nguyen Hoang; Phu, Nguyen Dang [Center for Materials Science, Faculty of Physics, Hanoi University of Science, Vietnam National University, Hanoi, 334 Nguyen Trai, Hanoi (Viet Nam); MacLaren, D A, E-mail: luongnh@vnu.edu.vn [School of Physics and Astronomy, University of Glasgow, Glasgow, G12 8QQ (United Kingdom)

2011-07-15

Co-Pt nanoparticles encapsulated in carbon cages have been prepared by sonoelectrodeposition followed by annealing in a CO atmosphere. Sonoelectrodeposition is a useful technique to make metallic nanoparticles, using ultrasound during electrodeposition to remove nanoparticles as they grow on the cathode surface. We used an electrolyte containing chloroplatinic acid and cobalt chloride and found that the atomic ratio of Co:Pt in the as-formed materials varied from 0.2 to 0.8 as the deposition current density was changed from 15 to 35 mA cm{sup -2}. However, the as-deposited materials were inhomogeneous, comprising a mixture of Pt-rich and Co-rich nanoparticles. X-ray diffraction indicated that subsequent heat treatment (700 deg. C for 1 h) under CO gas created an ordered CoPt alloy phase that exhibited hard magnetic properties. Transmission electron microscopy showed many of the resulting nanoparticles to be encapsulated in carbon cages, which we ascribe to Co-catalyzed decomposition of CO during annealing. The thickness of the carbon cages was about ten layers, which may have helped reduce sintering during annealing. The size of the resultant nanoparticles was about 100 nm diameter, larger than the typical 5-10 nm diameter of as-deposited nanoparticles.

International market assessment of stand-alone photovoltaic power systems for cottage industry applications

Science.gov (United States)

Philippi, T. M.

1981-01-01

The final result of an international assessment of the market for stand-alone photovoltaic systems in cottage industry applications is reported. Nonindustrialized countries without centrally planned economies were considered. Cottage industries were defined as small rural manufacturers, employing less than 50 people, producing consumer and simple products. The data to support this analysis were obtained from secondary and expert sources in the U.S. and in-country field investigations of the Philippines and Mexico. The near-term market for photovoltaics for rural cottage industry applications appears to be limited to demonstration projects and pilot programs, based on an in-depth study of the nature of cottage industry, its role in the rural economy, the electric energy requirements of cottage industry, and a financial analysis of stand-alone photovoltaic systems as compared to their most viable competitor, diesel driven generators. Photovoltaics are shown to be a better long-term option only for very low power requirements. Some of these uses would include clay mixers, grinders, centrifuges, lathes, power saws and lighting of a workshop.

International market assessment of stand-alone photovoltaic power systems for cottage industry applications

Science.gov (United States)

Philippi, T. M.

1981-11-01

The final result of an international assessment of the market for stand-alone photovoltaic systems in cottage industry applications is reported. Nonindustrialized countries without centrally planned economies were considered. Cottage industries were defined as small rural manufacturers, employing less than 50 people, producing consumer and simple products. The data to support this analysis were obtained from secondary and expert sources in the U.S. and in-country field investigations of the Philippines and Mexico. The near-term market for photovoltaics for rural cottage industry applications appears to be limited to demonstration projects and pilot programs, based on an in-depth study of the nature of cottage industry, its role in the rural economy, the electric energy requirements of cottage industry, and a financial analysis of stand-alone photovoltaic systems as compared to their most viable competitor, diesel driven generators. Photovoltaics are shown to be a better long-term option only for very low power requirements. Some of these uses would include clay mixers, grinders, centrifuges, lathes, power saws and lighting of a workshop.

Implementing a bar-code assisted medication administration system: effects on the dispensing process and user perceptions.

Science.gov (United States)

Samaranayake, N R; Cheung, S T D; Cheng, K; Lai, K; Chui, W C M; Cheung, B M Y

2014-06-01

We assessed the effects of a bar-code assisted medication administration system used without the support of computerised prescribing (stand-alone BCMA), on the dispensing process and its users. The stand-alone BCMA system was implemented in one ward of a teaching hospital. The number of dispensing steps, dispensing time and potential dispensing errors (PDEs) were directly observed one month before and eight months after the intervention. Attitudes of pharmacy and nursing staff were assessed using a questionnaire (Likert scale) and interviews. Among 1291 and 471 drug items observed before and after the introduction of the technology respectively, the number of dispensing steps increased from five to eight and time (standard deviation) to dispense one drug item by one staff personnel increased from 0.8 (0.09) to 1.5 (0.12) min. Among 2828 and 471 drug items observed before and after the intervention respectively, the number of PDEs increased significantly (Psystem offered less benefit to the dispensing process (9/16). Nursing staff perceived the system as useful in improving the accuracy of drug administration (7/10). Implementing a stand-alone BCMA system may slow down and complicate the dispensing process. Nursing staff believe the stand-alone BCMA system could improve the drug administration process but pharmacy staff believes the technology would be more helpful if supported by computerised prescribing. However, periodical assessments are needed to identify weaknesses in the process after implementation, and all users should be educated on the benefits of using this technology. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Future UK markets for stand-alone renewable energy systems

International Nuclear Information System (INIS)

Paish, O.

1999-01-01

A study to identify and quantify the market for stand-alone renewable energy supplies of power (photovoltaics, wind and micro-hydro electricity systems) was described. The study focused on small systems, generally less than a few kW installed capacity. It was suggested that in the UK, the emphasis on grid-connected renewable energy technologies (RETs) has blurred the fact that it is 'off-grid' renewable systems that can offer more immediate real commercial markets for the renewables business. With the likelihood of a significant increase in demand for renewables world wide over the next ten years, the UK needs to make a special effort to become involved

Effects of perch on feed consumption and behaviour of caged laying hens

OpenAIRE

E. VALKONEN; R. RINNE; J. VALAJA

2008-01-01

This experiment studied the effects of perches in furnished cages on behaviour and feed consumption of laying hens. The study used 352 Lohmann Selected Leghorn (LSL) hens. The hens were housed at 16 weeks of age in furnished cages in groups of 8 birds. The experiment lasted for 205 days. The treatments were: perches present from 16 weeks of age (P16), perches present from 19 weeks of age (P19), and no perches present (NP). Feed consumption and egg production were measured over the pre-laying ...

Assessment of Stand-Alone Displays for Time Management in a Creativity-Driven Learning Environment

DEFF Research Database (Denmark)

Frimodt-Møller, Søren

2017-01-01

This paper considers the pros and cons of stand-alone displays, analog (e.g. billboards, blackboards, whiteboards, large pieces of paper etc.) as well as digital (e.g. large shared screens, digital whiteboards or similar), as tools for time management processes in a creativity-driven learning...

Trp-cage: Folding free energy landscape in explicit water

Science.gov (United States)

Zhou, Ruhong

2003-11-01

Trp-cage is a 20-residue miniprotein, which is believed to be the fastest folder known so far. In this study, the folding free energy landscape of Trp-cage has been explored in explicit solvent by using an OPLSAA force field with periodic boundary condition. A highly parallel replica exchange molecular dynamics method is used for the conformation space sampling, with the help of a recently developed efficient molecular dynamics algorithm P3ME/RESPA (particle-particle particle-mesh Ewald/reference system propagator algorithm). A two-step folding mechanism is proposed that involves an intermediate state where two correctly formed partial hydrophobic cores are separated by an essential salt-bridge between residues Asp-9 and Arg-16 near the center of the peptide. This metastable intermediate state provides an explanation for the superfast folding process. The free energy landscape is found to be rugged at low temperatures, and then becomes smooth and funnel-like above 340 K. The lowest free energy structure at 300 K is only 1.50 Å C-RMSD (C-rms deviation) from the NMR structures. The simulated nuclear Overhauser effect pair distances are in excellent agreement with the raw NMR data. The temperature dependence of the Trp-cage population, however, is found to be significantly different from experiment, with a much higher melting transition temperature above 400 K (experimental 315 K), indicating that the current force fields, parameterized at room temperature, need to be improved to correctly predict the temperature dependence.

Video Monitoring and Analysis System for Vivarium Cage Racks | NCI Technology Transfer Center | TTC

Science.gov (United States)

This invention pertains to a system for continuous observation of rodents in home-cage environments with the specific aim to facilitate the quantification of activity levels and behavioral patterns for mice housed in a commercial ventilated cage rack.  The National Cancer Institute’s Radiation Biology Branch seeks partners interested in collaborative research to co-develop a video monitoring system for laboratory animals.

Faraday cage-type electrochemiluminescence immunosensor for ultrasensitive detection of Vibrio vulnificus based on multi-functionalized graphene oxide.

Science.gov (United States)

Guo, Zhiyong; Sha, Yuhong; Hu, Yufang; Yu, Zhongqing; Tao, Yingying; Wu, Yanjie; Zeng, Min; Wang, Sui; Li, Xing; Zhou, Jun; Su, Xiurong

2016-10-01

A novel Faraday cage-type electrochemiluminescence (ECL) immunosensor devoted to the detection of Vibrio vulnificus (VV) was fabricated. The sensing strategy was presented by a unique Faraday cage-type immunocomplex based on immunomagnetic beads (IMBs) and multi-functionalized graphene oxide (GO) labeled with (2,2'-bipyridine)(5-aminophenanthroline)ruthenium (Ru-NH2). The multi-functionalized GO could sit on the electrode surface directly due to the large surface area, abundant functional groups, and good electronic transport property. It ensures that more Ru-NH2 is entirely caged and become "effective," thus improving sensitivity significantly, which resembles extending the outer Helmholtz plane (OHP) of the electrode. Under optimal conditions, the developed immunosensor achieves a limit of detection as low as 1 CFU/mL. Additionally, the proposed immunosensor with high sensitivity and selectivity can be used for the detection of real samples. The novel Faraday cage-type method has shown potential application for the diagnosis of VV and opens up a new avenue in ECL immunoassay. Graphical abstract Faraday cage-type immunoassay mode for ultrasensitive detection by extending OHP.

Assessment of the effects of cage fish-farming on damselfish-associated food chains using stable-isotope analyses

International Nuclear Information System (INIS)

Jan, Rong-Quen; Kao, Shuh-Ji; Dai, Chang-Feng; Ho, Cheng-Tze

2014-01-01

Highlights: • Damselfishes living at sites near a cage farm bore lower δ 13 C and higher δ 15 N. • Similar trends occurred in zooplankton and detritus, major foods for damselfishes. • δ 15 N enrichment in fish may have arisen from the uptake of excess feed and prey. • Farm wastes were documented entering the ecosystem through the pelagic food chain. • No clear evidence of the effects of cage farming on stable isotopes in macroalgae. - Abstract: To assess the effect of cage fish-farming on the coral reef ecosystem off Xiaoliuchiu Island, southern Taiwan, geographical differences in the food chain of each of two damselfishes, Pomacentrus vaiuli and Chromis margaritifer, were examined using a stable-isotope approach. For each damselfish, individuals were found to consume similar foods at all sites. However, specimens collected at sites near the cage farm (as the experimental sites) exhibited lower δ 13 C and higher δ 15 N signatures compared to those from reference sites. Similar trends also occurred in the zooplankton and detritus, two major food sources for both damselfishes. This finding indicates that particulate organic matter released by the farm may have entered the coral reef ecosystem through the pelagic food chain. Artificial reef emplacement is recommended to provide extra habitats under cage farms to support additional pelagic-feeding fish populations, thereby reducing environmental impacts of cage farming on coral reefs

Robust Power Management Control for Stand-Alone Hybrid Power Generation System

International Nuclear Information System (INIS)

Kamal, Elkhatib; Adouane, Lounis; Aitouche, Abdel; Mohammed, Walaa

2017-01-01

This paper presents a new robust fuzzy control of energy management strategy for the stand-alone hybrid power systems. It consists of two levels named centralized fuzzy supervisory control which generates the power references for each decentralized robust fuzzy control. Hybrid power systems comprises: a photovoltaic panel and wind turbine as renewable sources, a micro turbine generator and a battery storage system. The proposed control strategy is able to satisfy the load requirements based on a fuzzy supervisor controller and manage power flows between the different energy sources and the storage unit by respecting the state of charge and the variation of wind speed and irradiance. Centralized controller is designed based on If-Then fuzzy rules to manage and optimize the hybrid power system production by generating the reference power for photovoltaic panel and wind turbine. Decentralized controller is based on the Takagi-Sugeno fuzzy model and permits us to stabilize each photovoltaic panel and wind turbine in presence of disturbances and parametric uncertainties and to optimize the tracking reference which is given by the centralized controller level. The sufficient conditions stability are formulated in the format of linear matrix inequalities using the Lyapunov stability theory. The effectiveness of the proposed Strategy is finally demonstrated through a SAHPS (stand-alone hybrid power systems) to illustrate the effectiveness of the overall proposed method. (paper)

Linguistic and Structural Analyses of Stand-Alone Literature Reviews: Seventy-Five Years of Change

Science.gov (United States)

Wright, Heidi Rachel

2016-01-01

The purpose of this dissertation is to offer a multifaceted overview of stand-alone literature reviews. These texts, literature reviews published unattached to research articles, have existed for centuries but remained largely unstudied by linguists. Thus, the goal of this project is to present these reviews' situational, grammatical, and…

PRODUCTIVITY OF LAYERS AND EGG QUALITY IN FREE RANGE AND CAGE SYSTEM OF HOUSING

Directory of Open Access Journals (Sweden)

Đ. Senčić

2006-12-01

Full Text Available The research was conducted with two groups of Lohmann Brown hybrid layers. Production of eggs lasted for 52 weeks. A control group of layers was kept in the conventional housing system, that is, in cages, while experimental group was kept in the free range system. Layers from the free range system, compared to those kept in cages, laid fewer eggs, (266:295, they consumed more feed on daily basis (129 g : 115 g, more feed per kilogram of egg weight (2.83 kg : 2.35 kg, they had higher mortality rate (6.80 % : 5.50 % and lower end of lay body weight (1.95 kg : 2.10 kg. Eggs from free range layers, compared to those from the cages system, had significantly (P0.05 were determined between the free range and the cages system of housing hens. Considering somewhat lower productivity and higher mortality rate of hens, higher feed consumption per kilogram of egg mass, but also better quality of eggs, profitability of egg production in the free range system will depend, to the maximum extent, on market evaluation of the production.

Behavior and Welfare of Domestic Cats Housed in Cages Larger than U.S. Norm.

Science.gov (United States)

Stella, Judith L; Croney, Candace C; Buffington, C Tony

2017-01-01

The effect of providing additional floor space on cat behavior and welfare is not well documented. This study involved replication of an investigation of cats' responses to enhanced cage and room environments using cages of 0.56 m 2 with the same methodology but an increased space allowance of 1.1 m 2 . Singly housed adult cats (n = 59) were randomly assigned to a treatment group that was a combination of a managed or unmanaged room and an enriched or unenriched cage environment. Cats were observed for 2 days for maintenance, affiliative, and avoidant behaviors using scan sampling and 5-min, continuous focal sampling. At the end of Day 2, cats' reactions to the approach of an unfamiliar person were assessed. Cats housed in enriched/managed environments exhibited more maintenance and affiliative behaviors and fewer avoidant behaviors than cats in unmanaged/unenriched environments, suggesting that macro and micro environments may be equally relevant to the cat. Increased space did not enhance the cats' welfare outcomes, suggesting that the provision of additional cage space may not be as important to the cat as a managed housing environment.

Sadhana | Indian Academy of Sciences

Indian Academy of Sciences (India)

There have been renewed interests in slip-ring induction machines due to their increasing use in both grid connected and stand-alone wind power generation schemes. Despite the squirrel cage induction generators' advantages of being brushless, low-cost, needing less maintenance and having inherent overload ...

Conformational effects on Carbon-13 NMR spectra of half-cage alcohols

Energy Technology Data Exchange (ETDEWEB)

Seidl, Peter Rudolf [Universidade Federal (UFRJ), Rio de Janeiro, RJ (Brazil). Escola de Quimica; Carneiro, J. Walkimar de M. [Universidade Federal Fluminense (UFF), Niteroi, RJ (Brazil). Dept. de Quimica Geral e Inorganica; Tostes, Glauco R. [Universidade Federal do Norte Fluminense (UENSP). Campos dos Goytacazes, RJ (Brazil). Centro de Ciencias e Tecnologia; Pinto, Paulo S.S. [Instituto Militar de Engenharia (IME), Rio de Janeiro, RJ (Brazil). Dept. de Engenharia Quimica; Costa, Valentim E.U.; Alifantes, Joao [Rio Grande do Sul Univ. (UFRGS), Porto Alegre (Brazil). Inst. de Quimica; Bernassau, Jean-Marie; Sizun, Philippe [SANOFI Recherche, Montpellier (France)

1999-05-01

Rotation around the carbon=oxygen bond of the hydroxyl group of half-cage alcohols affects bond lengths and angles as well as charge distribution on carbon and hydrogen atoms. As derivatives of half-cage compounds have played an important role in the investigation of several phenomena of interest in the interpretation of NMR parameters, we calculated carbon -13 chemical shift for the three conformers of half-cage alcohols that were investigated at the 6-31 G{sup *} level. GIAO chemical shifts for 1 A, 1 B and 1 C (C{sub 6}-C{sub 5}-O-H dihedral angles of respectively, -73.6 deg C, 64.8 deg C and 178.0 deg C) were calculated by HF/6-31 g (d)// B3 LYP/6-31 g (d) and by B3LYP/6-31 g (d)//B3LYP/6-31 g (d). Since the later gave better agreement with the published chemical shifts and correctly predicts the order of shifts for 2-exo-norbornol, the bicyclic analog of 1, we took these calculations as a basis for analysis of conformational effects.

Quantum fluctuations of a fullerene cage modulate its internal magnetic environment.

Science.gov (United States)

Kawatsu, Tsutomu; Tachikawa, Masanori

2018-01-17

To investigate the effect of quantum fluctuations on the magnetic environment inside a C 60 fullerene cage, we have calculated the nuclear magnetic shielding constant of protons in H 2 @C 60 and HD@C 60 systems by on-the-fly ab initio path integral simulation, including both thermal and nuclear quantum effects. The most dominant upfield from an isolated hydrogen molecule occurs due to the diamagnetic current of the C 60 cage, which is partly cancelled by the paramagnetic current, where the paramagnetic contribution is enlarged by the zero-point vibrational fluctuation of the C 60 carbon backbone structure via a widely distributed HOMO-LUMO gap. This quantum modulation mechanism of the nuclear magnetic shielding constant is newly proposed. Because this quantum effect is independent of the difference between H 2 and HD, the H 2 /HD isotope shift occurs in spite of the C 60 cage. The nuclear magnetic constants computed for H 2 @C 60 and HD@C 60 are 32.047 and 32.081 ppm, respectively, which are in reasonable agreement with the corresponding values of 32.19 and 32.23 ppm estimated from the experimental values of the chemical shifts.

Minimum cost solution of wind–photovoltaic based stand-alone power systems for remote consumers

International Nuclear Information System (INIS)

Kaldellis, J.K.; Zafirakis, D.; Kavadias, K.

2012-01-01

Renewable energy sources (RES) based stand-alone systems employing either wind or solar power and energy storage comprise a reliable energy alternative, on top of conventional diesel-electric generator sets, commonly used by remote consumers. However, such systems usually imply the need for oversizing and considerable energy storage requirements leading to relatively high costs. On the other hand, hybrid configurations that may exploit both wind and solar potential of a given area may considerably reduce energy storage capacity and improve the economic performance of the system. In this context, an integrated techno-economic methodology for the evaluation of hybrid wind–photovoltaic stand-alone power systems is currently developed, aiming at the designation of optimum configurations for a typical remote consumer, using economic performance criteria. For the problem investigation, the developed evaluation model is applied to four representative areas of the Greek territory with different wind potential characteristics in order to obtain optimum configurations on the basis of minimum initial investment, 10-year and 20-year total cost. According to the results obtained, the proposed solution is favorably compared with all other stand-alone energy alternatives, reflecting the ability of hybrid systems to adjust even in areas where the local RES potential is not necessarily of high quality. - Highlights: ► Wind- and PV-stand alone systems often imply use of extreme battery capacity. ► Hybrid wind–PV systems may reduce energy storage requirements and associated costs. ► An optimization methodology is developed, based on economic performance criteria. ► Methodology is applied to four Greek regions of different wind potential. ► Results obtained reflect the hybrid solution's advantages over other alternatives.

Microbial control of caged population of Zonocerus variegatus using ...

African Journals Online (AJOL)

Microbial control of caged populations of Zonocerus variegatus was carried out using indigenous fungal entomopathogens isolated from the grasshopper's cadaver. Bioassay response indicated a dose-dependent mortality coupled with drastic reduction in food consumption among spores infected grasshoppers. Lethal time ...

MOSFET Loss Evaluation for a Low-Power Stand-Alone Photovoltaic-LED System

DEFF Research Database (Denmark)

Mira Albert, Maria del Carmen; Knott, Arnold; Andersen, Michael A. E.

2015-01-01

This paper presents a performance evaluation and comparison of state-of-the-art low voltage Si MOSFETs for a stand-alone photovoltaic-LED Light to Light (LtL) system. The complete system is formed by two cascaded converters that will be optimized for a determined solar irradiation and LED...... illumination profiles. The comparison is performed based on dynamic characterization and evaluation of the devices energy loss at different current levels....

Use, fate and ecological risks of antibiotics applied in tilapia cage farming in Thailand

Energy Technology Data Exchange (ETDEWEB)

Rico, Andreu [Department of Aquatic Ecology and Water Quality Management, Wageningen University, Wageningen University and Research Centre, P.O. Box 47, 6700 AA Wageningen (Netherlands); Oliveira, Rhaul [Department of Biology and CESAM, University of Aveiro, Campus Universitario de Santiago, 3810-193 Aveiro (Portugal); McDonough, Sakchai [Aquaculture and Aquatic Resources Management, Asian Institute of Technology, P.O. Box 4, Klong Luang, Pathumthani 12120 (Thailand); Matser, Arrienne [Alterra, Wageningen University and Research Centre, P.O. Box 47, 6700 AA Wageningen (Netherlands); Khatikarn, Jidapa [Department of Aquatic Ecology and Water Quality Management, Wageningen University, Wageningen University and Research Centre, P.O. Box 47, 6700 AA Wageningen (Netherlands); Department of Fishery Biology, Faculty of Fisheries, Kasetsart University, Chatuchak 10900, Bangkok (Thailand); Satapornvanit, Kriengkrai [Department of Fishery Biology, Faculty of Fisheries, Kasetsart University, Chatuchak 10900, Bangkok (Thailand); Nogueira, António J.A.; Soares, Amadeu M.V.M.; Domingues, Inês [Department of Biology and CESAM, University of Aveiro, Campus Universitario de Santiago, 3810-193 Aveiro (Portugal); Van den Brink, Paul J. [Department of Aquatic Ecology and Water Quality Management, Wageningen University, Wageningen University and Research Centre, P.O. Box 47, 6700 AA Wageningen (Netherlands); Alterra, Wageningen University and Research Centre, P.O. Box 47, 6700 AA Wageningen (Netherlands)

2014-08-01

The use, environmental fate and ecological risks of antibiotics applied in tilapia cage farming were investigated in the Tha Chin and Mun rivers in Thailand. Information on antibiotic use was collected through interviewing 29 farmers, and the concentrations of the most commonly used antibiotics, oxytetracycline (OTC) and enrofloxacin (ENR), were monitored in river water and sediment samples. Moreover, we assessed the toxicity of OTC and ENR on tropical freshwater invertebrates and performed a risk assessment for aquatic ecosystems. All interviewed tilapia farmers reported to routinely use antibiotics. Peak water concentrations for OTC and ENR were 49 and 1.6 μg/L, respectively. Antibiotics were most frequently detected in sediments with concentrations up to 6908 μg/kg d.w. for OTC, and 2339 μg/kg d.w. for ENR. The results of this study indicate insignificant short-term risks for primary producers and invertebrates, but suggest that the studied aquaculture farms constitute an important source of antibiotic pollution. - Highlights: • First study assessing the risks of antibiotics applied in freshwater tilapia cages. • Ten antibiotics were reported to be used by tilapia cage farmers in two Thai rivers. • Peak oxytetracycline and enrofloxacin concentrations were in the order of μg/L. • Antibiotic concentrations in river sediments next to cages were up to several mg/kg. • Antibiotics are not posing a short-term risk for pelagic aquatic organisms. - Antibiotics applied in tilapia cage farming in Thailand are released into surrounding aquatic ecosystems and constitute an important source of environmental pollution.

Use, fate and ecological risks of antibiotics applied in tilapia cage farming in Thailand

International Nuclear Information System (INIS)

Rico, Andreu; Oliveira, Rhaul; McDonough, Sakchai; Matser, Arrienne; Khatikarn, Jidapa; Satapornvanit, Kriengkrai; Nogueira, António J.A.; Soares, Amadeu M.V.M.; Domingues, Inês; Van den Brink, Paul J.

2014-01-01

The use, environmental fate and ecological risks of antibiotics applied in tilapia cage farming were investigated in the Tha Chin and Mun rivers in Thailand. Information on antibiotic use was collected through interviewing 29 farmers, and the concentrations of the most commonly used antibiotics, oxytetracycline (OTC) and enrofloxacin (ENR), were monitored in river water and sediment samples. Moreover, we assessed the toxicity of OTC and ENR on tropical freshwater invertebrates and performed a risk assessment for aquatic ecosystems. All interviewed tilapia farmers reported to routinely use antibiotics. Peak water concentrations for OTC and ENR were 49 and 1.6 μg/L, respectively. Antibiotics were most frequently detected in sediments with concentrations up to 6908 μg/kg d.w. for OTC, and 2339 μg/kg d.w. for ENR. The results of this study indicate insignificant short-term risks for primary producers and invertebrates, but suggest that the studied aquaculture farms constitute an important source of antibiotic pollution. - Highlights: • First study assessing the risks of antibiotics applied in freshwater tilapia cages. • Ten antibiotics were reported to be used by tilapia cage farmers in two Thai rivers. • Peak oxytetracycline and enrofloxacin concentrations were in the order of μg/L. • Antibiotic concentrations in river sediments next to cages were up to several mg/kg. • Antibiotics are not posing a short-term risk for pelagic aquatic organisms. - Antibiotics applied in tilapia cage farming in Thailand are released into surrounding aquatic ecosystems and constitute an important source of environmental pollution

Quantum translator-rotator: inelastic neutron scattering of dihydrogen molecules trapped inside anisotropic fullerene cages.

Science.gov (United States)

Horsewill, A J; Panesar, K S; Rols, S; Johnson, M R; Murata, Y; Komatsu, K; Mamone, S; Danquigny, A; Cuda, F; Maltsev, S; Grossel, M C; Carravetta, M; Levitt, M H

2009-01-09

We report an inelastic neutron scattering investigation of the quantum dynamics of hydrogen molecules trapped inside anisotropic fullerene cages. Transitions among the manifold of quantized rotational and translational states are directly observed. The spectra recorded as a function of energy and momentum transfer are interpreted in terms of the rotational potential and the cage dimensions. The thermodynamics of orthohydrogen and parahydrogen are investigated through temperature dependence measurements.

Characteristics Of Smoked Catfish (Hemibagrus Nemurus) Prepared Frompond Culture, Cage And Wild Fish

OpenAIRE

Maskilin, Jippo; Hasan, Bustari; Leksono, Tjipto

2017-01-01

This study was aimed to evaluate the sensory quality, proximate composition, amino acids and fatty acids profiles of smoked catfish prepared from pond, cage culture and wild fish. Catfish samples 300-350 grams in weight wastaken respectualy from wild (Kampar river), pond and cage culture in Sungai Paku, Kampar. The fish was smoked using hot smoking method, and the smoked fish was evaluated for smoking yield, sensory quality, proximate composition, amino acid and fatty acid profile.The smoking...

Methodology for the design of a stand-alone photovoltaic power supply

OpenAIRE

López Seguel, Julio; Seleme Junior, Seleme Isaac; Donoso-Garcia, Pedro F; Ferreira Morais, Lenin Martins; Cabaleiro Cortizo, Porfirio; Severo Mendes, Marcos A

2013-01-01

This paper presents a complete methodology for the design of an autonomous photovoltaic system to maximize the use of solar energy. It is a method that prioritizes the best cost-effective choice at every step of the project. In order to ensure the proper use and extended battery life time, a control strategy for charging the batteries is proposed. Experimental results are provided for a stand-alone photovoltaic system with low electrical power, intended primarily for the illumination and basi...

Tissue engineering rib with the incorporation of biodegradable polymer cage and BMSCs/decalcified bone: an experimental study in a canine model.

Science.gov (United States)

Tang, Hua; Wu, Bin; Qin, Xiong; Zhang, Lu; Kretlow, Jim; Xu, Zhifei

2013-05-20

The reconstruction of large bone defects, including rib defects, remains a challenge for surgeons. In this study, we used biodegradable polydioxanone (PDO) cages to tissue engineer ribs for the reconstruction of 4cm-long costal defects. PDO sutures were used to weave 6cm long and 1cm diameter cages. Demineralized bone matrix (DBM) which is a xenograft was molded into cuboids and seeded with second passage bone marrow mesenchymal stem cells (BMSCs) that had been osteogenically induced. Two DBM cuboids seeded with BMSCs were put into the PDO cage and used to reconstruct the costal defects. Radiographic examination including 3D reconstruction, histologic examination and mechanical test was performed after 24 postoperative weeks. All the experimental subjects survived. In all groups, the PDO cage had completely degraded after 24 weeks and been replaced by fibrous tissue. Better shape and radian were achieved in PDO cages filled with DBM and BMSCs than in the other two groups (cages alone, or cages filled with acellular DBM cuboids). When the repaired ribs were subjected to an outer force, the ribs in the PDO cage/DBMs/BMSCs group kept their original shape while ribs in the other two groups deformed. In the PDO cage/DBMs/BMSCs groups, we also observed bony union at all the construct interfaces while there was no bony union observed in the other two groups. This result was also confirmed by radiographic and histologic examination. This study demonstrates that biodegradable PDO cage in combination with two short BMSCs/DBM cuboids can repair large rib defects. The satisfactory repair rate suggests that this might be a feasible approach for large bone repair.

Mediterranean fruit fly: interference of oviposition by radiation-sterilized females in field cages

Energy Technology Data Exchange (ETDEWEB)

McInnis, D. O. [Tropical Fruit and Vegetable Research Lab. USDA-ARS, Honolulu, HI (United States); Wong, T. T.Y.

1990-07-01

In experiments between April and September 1984, the behaviour of nonirradiated and radiation-sterilized laboratory-adapted adults of the tephritid Ceratitis capitata was observed on apples hung on guava trees in outdoor cages in Hawaii. The numbers of nonirradiated females observed resting on fruit were reduced several times by the presence of irradiated females, either alone or with irradiated males, but not by irradiated males alone. Similarly, the number of nonirradiated females observed ovipositing and the duration of oviposition was reduced by the presence of irradiated females. In control cages (all nonirradiated flies), the duration of oviposition by females averaged 255.9±15.0 s on fruit, while most of nonirradiated and irradiated females in the mixed (treatment) cage averaged 157±19.8 s and 77.5±7.5 s on fruit, resp. Irradiated females behaved skittishly on fruit and frequently engaged in physical encounters with other flies.

prfectBLAST: a platform-independent portable front end for the command terminal BLAST+ stand-alone suite.

Science.gov (United States)

Santiago-Sotelo, Perfecto; Ramirez-Prado, Jorge Humberto

2012-11-01

prfectBLAST is a multiplatform graphical user interface (GUI) for the stand-alone BLAST+ suite of applications. It allows researchers to do nucleotide or amino acid sequence similarity searches against public (or user-customized) databases that are locally stored. It does not require any dependencies or installation and can be used from a portable flash drive. prfectBLAST is implemented in Java version 6 (SUN) and runs on all platforms that support Java and for which National Center for Biotechnology Information has made available stand-alone BLAST executables, including MS Windows, Mac OS X, and Linux. It is free and open source software, made available under the GNU General Public License version 3 (GPLv3) and can be downloaded at www.cicy.mx/sitios/jramirez or http://code.google.com/p/prfectblast/.

C-60 as a Faraday cage

OpenAIRE

Delaney, Paul; Greer, J.C.

2004-01-01

Endohedral fullerenes have been proposed for a number of technological uses, for example, as a nanoscale switch, memory bit and as qubits for quantum computation. For these technology applications, it is important to know the ease with which the endohedral atom can be manipulated using an applied electric field. We find that the Buckminsterfullerene (C-60) acts effectively as a small Faraday cage, with only 25% of the field penetrating the interior of the molecule. Thus influencing the atom i...

RESULTS OF THE USE OF PEEK CAGES IN THE TREATMENT OF BASILAR INVAGINATION BY GOEL TECHNIQUE

Directory of Open Access Journals (Sweden)

Luís Eduardo Carelli Teixeira da Silva

2016-03-01

Full Text Available ABSTRACT Objective: Analysis of the use of polyetheretherketone (PEEK cages for atlantoaxial facet realignment and distraction for treatment of basilar invagination by Goel technique. Method: Retrospective descriptive statistical analysis of the neurological status, pain, presence of subsidence and bone fusion with the use of PEEK cages in 8 atlantoaxial joints of 4 patients with basilar invagination. All patients were treated with atlantoaxial facet distraction and realignment and subsequent arthrodesis C1-C2 by the technique of Goel modified by the use of PEEK cage. Results: All patients showed improvement in Nurick neurological assessment scale and Visual Analogue Scale (VAS of pain. There were no cases of subsidence, migration, or damage to the vertebral artery during the insertion of the cage. All joints evolved with bone fusion, assessed by dynamic radiographs, and computed tomography. Two patients developed neuropathic pain in dermatome of C2 and one patient had unilateral vertebral artery injury during C2 instrumentation treated with insertion of pedicle screw to control the bleeding. Conclusion: The results of the treatment of basilar invagination by the Goel technique with the use of PEEK cages shown to be effective and safe although further studies are needed to confirm this use.

Analyzing grid extension and stand-alone photovoltaic systems for the cost-effective electrification of Kenya

NARCIS (Netherlands)

Zeyringer, Marianne; Pachauri, Shonali; Schmid, Erwin; Schmidt, Johannes; Worrell, Ernst|info:eu-repo/dai/nl/106856715; Morawetz, Ulrich B.

2015-01-01

The declaration of 2014-2024 as the Decade of Sustainable Energy for All has catalyzed actions towards achieving universal electricity access. The high costs of building electric infrastructure are a major impediment to improved access, making stand-alone photovoltaic (PV) systems an attractive

Dual Cage High Power Induction Motor with Direct Start-up. Design and FEM Analysis

Directory of Open Access Journals (Sweden)

LIVADARU, L.

2013-05-01

Full Text Available This paper presents an investigation on the design of high-power induction motor with special constraints. Direct online start-up and pull-up torque of rather high value represent two of the imposed requirements. Three different structures are analyzed, which involve deep bars, magnetic wedges and double cage respectively. The proposed solution advances a new rotor structure with two different rotor cages. The first cage acts mainly during start-up and is made of iron with both electric and magnetic properties. The second one is made of copper and represents the main rotor winding. It has a particular cross-section of the bars in order to carry into effect the required constraints both during start-up and steady-state. The proposed models are finally evaluated by means of finite element method analysis.

Modeling, design and analysis of a stand-alone hybrid power generation system using solar/urine

International Nuclear Information System (INIS)

Wu, Wei; Zhou, Ya-Yan; Lin, Mu-Hsuan; Hwang, Jenn-Jiang

2013-01-01

Highlights: • The stand-alone hybrid power system is presented. • The urine-to-hydrogen processor is proposed. • Scenario analysis of the hybrid power dispatching and the urine/solar demands is investigated. • The design, modeling and optimization of the hybrid power system is addressed by Aspen Plus and Matlab. - Abstract: The urine turned to hydrogen as an energy conversion process is integrated into a stand-alone hybrid (PV/FC/battery) power generation system. The optimization and simulation of a new urine-to-hydrogen processor is evaluated in Aspen Plus environment. In our approach, the PV generator aims to reduce urine consumption and the lithium-ion battery can compensate the power gap due to the fuel processing delay. Based on prescribed patterns of solar irradiation and the daily load demand of a 30-persons classroom, scenario analyses of the hybrid power dispatching and operational feasibility is addressed

Environmental impact analysis of aquaculture in net cages in a ...

African Journals Online (AJOL)

Environmental impact analysis of aquaculture in net cages in a Brazilian water reservoir, based in zooplankton communities. Maria Cristina Crispim, Karla Patrícia Ponte Araújo, Hênio do Nascimento Melo Júnior ...

Design and development of self-powered sensors on wireless sensor network for standalone plant critical data management during SBO and beyond design basis events

International Nuclear Information System (INIS)

Aparna, J.; Dulera, I.V.; Rama Rao, A.; Vijayan, P.K.

2015-01-01

Advanced reactors are designed with an aim of maximum safety, optimized fuel utilization and effective system design. Safety aspects in reactor designs are being viewed for all possible vulnerabilities, and as a result, robust self-regulating passive safety features have been favored in Gen IV and advanced reactor designs. In addition to passive systems, the accidents scenarios at Fukushima indicate the dire need of reliable and stand-alone self-powered sensors, for monitoring plant critical parameters for effective damage control actions. There is a strong need for plant critical data management and situation awareness during the unavailability of all conventional power sources in a nuclear power plant, during extended station blackout (SBO) conditions. These self-powered sensors would assist the operators in managing events like SBO and help in containing any Beyond Design Basis Events (BDBE) conditions, well away from the public domain

Anterior debridement and fusion followed by posterior pedicle screw fixation in pyogenic spondylodiscitis: autologous iliac bone strut versus cage.

Science.gov (United States)

Pee, Yong Hun; Park, Jong Dae; Choi, Young-Geun; Lee, Sang-Ho

2008-05-01

An anterior approach for debridement and fusion with autologous bone graft has been recommended as the gold standard for surgical treatment of pyogenic spondylodiscitis. The use of anterior foreign body implants at the site of active infection is still a challenging procedure for spine surgeons. Several authors have recently introduced anterior grafting with titanium mesh cages instead of autologous bone strut in the treatment of spondylodiscitis. The authors present their experience of anterior fusion with 3 types of cages followed by posterior pedicle screw fixation. They also compare their results with the use of autologous iliac bone strut. The authors retrospectively reviewed the cases of 60 patients with pyogenic spondylodiscitis treated by anterior debridement between January 2003 and April 2005. Fusion using either cages or iliac bone struts was performed during the same course of anesthesia followed by posterior fixation. Twenty-three patients underwent fusion with autologous iliac bone strut, and 37 patients underwent fusion with 1 of the 3 types of cages. The infections resolved in all patients, as noted by normalization of their erythrocyte sedimentation rates and C-reactive protein levels. Patients in both groups were evaluated in terms of their preoperative and postoperative clinical and imaging findings. Single-stage anterior debridement and cage fusion followed by posterior pedicle screw fixation can be effective in the treatment of pyogenic spondylodiscitis. There was no difference in clinical and imaging outcomes between the strut group and cage group except for the subsidence rate. The subsidence rate was higher in the strut group than in the cage group. The duration until subsidence was also shorter in the strut group than in the cage group.

Loss-of-load probabilities for stand-alone photovoltaic systems

International Nuclear Information System (INIS)

Klein, S.A.; Beckman, W.A.

1989-01-01

A general method is presented for estimating the loss-of-load probability of stand-alone photovoltaic systems. The method was developed by correlating simulation results. The simulations were driven with synthetic radiation sequences having the same statistical significance as available historical data. The methods assumes a constant nighttime load and accounts for the distribution and persistence in daily solar radiation data. It is shown that the 10 year average performance of systems having loss-of-load probabilities less than about 0.01 can vary greatly from one ten year period to the next and thereby cannot be considered realistic performance estimates of a system during its lifetime. (author). 26 refs, 15 figs, 4 tabs

COMBINATION THERAPIES OR STANDALONE INTERVENTIONS? INNOVATION OPTIONS FOR PHARMACEUTICAL FIRMS FIGHTING CANCER

OpenAIRE

GUNJAN BHARDWAJ; ANSHIT AGRAWAL; RUPESH TYAGI

2015-01-01

Innovation is key to the pharma model, from an initial discovery to the final development of a marketable drug. Here, we explore the innovation options in the fiercely contested therapeutic area of Oncology. We studied clinical development of drugs targeting PD-1 and PD-L1 pathway. In this interesting contest, companies seem to be focusing on standalone interventions (exploratory innovation) and combination therapy (exploitative innovation) in clinical development. Merck Sharp and Dohme, havi...

Optimum Availability of Standalone Photovoltaic Power Systems for Remote Housing Electrification

Directory of Open Access Journals (Sweden)

Tamer Khatib

2014-01-01

Full Text Available The availability of PV systems is discussed to determine the optimum availability at which standalone PV systems must be designed. Optimization methods and PV systems software, such as HOMER and PV.MY, were used for this purpose. Six PV systems with six availability levels were analyzed, in terms of wasted energy, cost of energy, battery usage, and power shortages, using real meteorological data. Results show that PV systems with 99% availability are recommended, because of their high reliability and favorably wasted energy.

FANTOM5 CAGE profiles of human and mouse samples

NARCIS (Netherlands)

Noguchi, Shuhei; Arakawa, Takahiro; Fukuda, Shiro; Furuno, Masaaki; Hasegawa, Akira; Hori, Fumi; Ishikawa-Kato, Sachi; Kaida, Kaoru; Kaiho, Ai; Kanamori-Katayama, Mutsumi; Kawashima, Tsugumi; Kojima, Miki; Kubosaki, Atsutaka; Manabe, Ri-ichiroh; Murata, Mitsuyoshi; Nagao-Sato, Sayaka; Nakazato, Kenichi; Ninomiya, Noriko; Nishiyori-Sueki, Hiromi; Noma, Shohei; Saijyo, Eri; Saka, Akiko; Sakai, Mizuho; Simon, Christophe; Suzuki, Naoko; Tagami, Michihira; Watanabe, Shoko; Yoshida, Shigehiro; Arner, Peter; Axton, Richard A.; Babina, Magda; Baillie, J. Kenneth; Barnett, Timothy C.; Beckhouse, Anthony G.; Blumenthal, Antje; Bodega, Beatrice; Bonetti, Alessandro; Briggs, James; Brombacher, Frank; Carlisle, Ailsa J.; Clevers, Hans C.; Davis, Carrie A.; Detmar, Michael; Dohi, Taeko; Edge, Albert S. B.; Edinger, Matthias; Ehrlund, Anna; Ekwall, Karl; Endoh, Mitsuhiro; Enomoto, Hideki; Eslami, Afsaneh; Fagiolini, Michela; Fairbairn, Lynsey; Farach-Carson, Mary C.; Faulkner, Geoffrey J.; Ferrai, Carmelo; Fisher, Malcolm E.; Forrester, Lesley M.; Fujita, Rie; Furusawa, Jun-ichi; Geijtenbeek, Teunis B.; Gingeras, Thomas; Goldowitz, Daniel; Guhl, Sven; Guler, Reto; Gustincich, Stefano; Ha, Thomas J.; Hamaguchi, Masahide; Hara, Mitsuko; Hasegawa, Yuki; Herlyn, Meenhard; Heutink, Peter; Hitchens, Kelly J.; Hume, David A.; Ikawa, Tomokatsu; Ishizu, Yuri; Kai, Chieko; Kawamoto, Hiroshi; Kawamura, Yuki I.; Kempfle, Judith S.; Kenna, Tony J.; Kere, Juha; Khachigian, Levon M.; Kitamura, Toshio; Klein, Sarah; Klinken, S. Peter; Knox, Alan J.; Kojima, Soichi; Koseki, Haruhiko; Koyasu, Shigeo; Lee, Weonju; Lennartsson, Andreas; Mackay-sim, Alan; Mejhert, Niklas; Mizuno, Yosuke; Morikawa, Hiromasa; Morimoto, Mitsuru; Moro, Kazuyo; Morris, Kelly J.; Motohashi, Hozumi; Mummery, Christine L.; Nakachi, Yutaka; Nakahara, Fumio; Nakamura, Toshiyuki; Nakamura, Yukio; Nozaki, Tadasuke; Ogishima, Soichi; Ohkura, Naganari; Ohno, Hiroshi; Ohshima, Mitsuhiro; Okada-Hatakeyama, Mariko; Okazaki, Yasushi; Orlando, Valerio; Ovchinnikov, Dmitry A.; Passier, Robert; Patrikakis, Margaret; Pombo, Ana; Pradhan-Bhatt, Swati; Qin, Xian-Yang; Rehli, Michael; Rizzu, Patrizia; Roy, Sugata; Sajantila, Antti; Sakaguchi, Shimon; Sato, Hiroki; Satoh, Hironori; Savvi, Suzana; Saxena, Alka; Schmidl, Christian; Schneider, Claudio; Schulze-Tanzil, Gundula G.; Schwegmann, Anita; Sheng, Guojun; Shin, Jay W.; Sugiyama, Daisuke; Sugiyama, Takaaki; Summers, Kim M.; Takahashi, Naoko; Takai, Jun; Tanaka, Hiroshi; Tatsukawa, Hideki; Tomoiu, Andru; Toyoda, Hiroo; van de Wetering, Marc; van den Berg, Linda M.; Verardo, Roberto; Vijayan, Dipti; Wells, Christine A.; Winteringham, Louise N.; Wolvetang, Ernst; Yamaguchi, Yoko; Yamamoto, Masayuki; Yanagi-Mizuochi, Chiyo; Yoneda, Misako; Yonekura, Yohei; Zhang, Peter G.; Zucchelli, Silvia; Abugessaisa, Imad; Arner, Erik; Harshbarger, Jayson; Kondo, Atsushi; Lassmann, Timo; Lizio, Marina; Sahin, Serkan; Sengstag, Thierry; Severin, Jessica; Shimoji, Hisashi; Suzuki, Masanori; Suzuki, Harukazu; Kawai, Jun; Kondo, Naoto; Itoh, Masayoshi; Daub, Carsten O.; Kasukawa, Takeya; Kawaji, Hideya; Carninci, Piero; Forrest, Alistair R. R.; Hayashizaki, Yoshihide

2017-01-01

In the FANTOM5 project, transcription initiation events across the human and mouse genomes were mapped at a single base-pair resolution and their frequencies were monitored by CAGE (Cap Analysis of Gene Expression) coupled with single-molecule sequencing. Approximately three thousands of samples,

Pathogen Prevalence From Traditional Cage and Free Range Production

Science.gov (United States)

Overview: A study was conducted to determine if differences in pathogen prevalence occurred between a sister flock of conventional cage and free range laying hens. Both environmental and egg microbiology was monitored throughout 20 – 79 weeks of age. Salmonella, Campylobacter, and Listeria preval...

Diels-Alder reactions of inert aromatic compounds within a self-assembled coordination cage.

Science.gov (United States)

Horiuchi, Shinnosuke; Murase, Takashi; Fujita, Makoto

2011-07-04

A self-assembled coordination cage serves as a nanometer-sized molecular flask to promote the Diels-Alder reactions of aromatic hydrocarbons with N-cyclohexylmaleimide. The coordination cage accelerated the Diels-Alder reaction of anthracene at the electronically unfavorable, terminal benzene ring to give a compact, cavity-restrained syn-adduct. Activation-parameter measurements for the reactions revealed considerable reduction in the entropy cost, and preorganization of the substrates is a dominant factor in the enhanced reactivity. Owing to this entropy-cost reduction, otherwise-unreactive aromatic compounds, such as naphthalenes or triphenylene, also underwent Diels-Alder reactions in a regio- and stereocontrolled fashion. In the naphthalene Diels-Alder reaction, X-ray crystallographic analysis of the guest-inclusion complex clarified the reinforced orientation and proximity of the substrate pairs before the reaction. A perylene Diels-Alder adduct was stabilized inside the cage and protected from aerial oxidation. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Analysis of Heavy Metal Content (Pb) on Waters and Fish at The Floating Cages BPPP Ambon

Science.gov (United States)

Wattimena, Rachel L.; Selanno, Debby A. J.; Tuhumury, Semuel F.; Tuahatu, Juliana W.

2018-02-01

Coastal waters play important roles due to highly in natural resources and developing of environmental services. However, there are highly intensity of natural resources utilization, environment and settlement. Consequently, environment and natural resources would be degraded such as in the Ambon Bay. One of the potency at the Ambon Bay is mariculture area namely the floating cages (KJA) which belongs to Fisheries education and training (BPPP) Ambon. The research aimed to analyze physical-chemical of waters (temperature, pH, salinity and current speed), to analyze heavy metal concentration (Pb) on water and fish from floating cages (KJA) and to analyze waters pollution status at KJA BPPP Ambon. The average salinity of each floating cage ranged from 30.09 - 30.34°C, pH ranged from 8.03 - 8.44, salinity ranged from 31.36 - 33.34 PSU, and current speed at spring tide ranged from 0.5 - 55.8 Cm/sec while neap tide ranged from 0.1 - 9.8 Cm/sec. Heavy metal concentration (Pb) on waters was below the standard for waters quality and the average concentration was 0.002 mg/l. Whilst, the heavy metal concentration (Pb) on fishes was below standard for floating cages (floating cages 2-6) which was 0.05 and 0.17mg/l. Otherwise, floating cage 1 had been above maximum standard for fish food and its processing following SNI 7387:2009 (0.3mg/l) which was 0.31 mg/l. The status of waters pollution at KJA BPPP Ambon belonged to C class and could be categorized as moderate based on standard for waters quality issued by State Ministerial Decree for the Environment No. 51 Year 2004.

Design of a Stand-Alone Photovoltaic Model for Home Lightings and Clean Environment

Energy Technology Data Exchange (ETDEWEB)

Ani, Vincent Anayochukwu, E-mail: vincent_ani@yahoo.com [Department of Electronic Engineering, University of Nigeria, Nsukka (Nigeria)

2016-01-11

This paper gives a well-documented health risk of fuel-based lighting (kerosene lamps and fuel-powered generators) and proposed a design of a stand-alone solar PV system for sustainable home lightings in rural Nigerian area. The design was done in three different patterns of electricity consumptions with energy efficient lightings (EELs) using two different battery types (Rolls Surrette 6CS25PS and Hoppecke 10 OpzS 1000) on; (i) judicious power consumption, (ii) normal power consumption, and (iii) excess power consumption; and compared them with the incandescent light bulb consumption. The stand-alone photovoltaic energy systems were designed to match the rural Nigerian sunlight and weather conditions to meet the required lightings of the household. The objective function and constraints for the design models were formulated and optimization procedures were used to demonstrate the best solution (reliability at the lowest lifecycle cost). Initial capital costs as well as annualized costs over 5, 10, 15, 20, and 25 years were quantified and documented. The design identified the most cost-effective and reliable solar and battery array among the patterns of electricity consumption with EEL options (judicious power consumption, normal power consumption, and excess power consumption).

Design of a Stand-Alone Photovoltaic Model for Home Lightings and Clean Environment

International Nuclear Information System (INIS)

Ani, Vincent Anayochukwu

2016-01-01

This paper gives a well-documented health risk of fuel-based lighting (kerosene lamps and fuel-powered generators) and proposed a design of a stand-alone solar PV system for sustainable home lightings in rural Nigerian area. The design was done in three different patterns of electricity consumptions with energy efficient lightings (EELs) using two different battery types (Rolls Surrette 6CS25PS and Hoppecke 10 OpzS 1000) on; (i) judicious power consumption, (ii) normal power consumption, and (iii) excess power consumption; and compared them with the incandescent light bulb consumption. The stand-alone photovoltaic energy systems were designed to match the rural Nigerian sunlight and weather conditions to meet the required lightings of the household. The objective function and constraints for the design models were formulated and optimization procedures were used to demonstrate the best solution (reliability at the lowest lifecycle cost). Initial capital costs as well as annualized costs over 5, 10, 15, 20, and 25 years were quantified and documented. The design identified the most cost-effective and reliable solar and battery array among the patterns of electricity consumption with EEL options (judicious power consumption, normal power consumption, and excess power consumption).

Trace elements in two marine fish cultured in fish cages in Fujian province, China

International Nuclear Information System (INIS)

Onsanit, Sarayut; Ke Caihuan; Wang Xinhong; Wang Kejian; Wang Wenxiong

2010-01-01

Two cultured marine fish, the Japanese seabass (Lateolabrax japonicus) and red seabream (Pagrus major) were collected from eight fish cage sites along the coast of Fujian province in China. The concentrations of Ag, As, Cd, Co, Cu, Fe, Mn, Se, and Zn in their muscle, stomach and liver tissue were quantified. The risk of these trace elements to humans through fish consumption was then assessed. The highest concentrations of As, Cd, Se and Zn in fish feed from fish cages were found in Dongshan Station. Moreover, the As levels in the muscles of both species at all sites were generally higher than China's national standard (>1.0 μg/g). Trace element concentrations in two marine fish followed the order of livers > stomachs > muscles. Although the As levels in two marine caged fish exceeded the permissible standards, the estimated daily intake of As did not exceed the reference dose guideline established by US EPA. For other trace elements examined in this study, their concentrations did not exceed the permissible concentrations of the international standards. - As levels in two marine caged fish from China exceeded the permissible standards, whereas the levels of others trace elements did not exceed the permissible concentrations.

Effect of thermal processing on retinol levels of free-range and caged hen eggs.

Science.gov (United States)

Ramalho, Héryka M M; Santos, Videanny V A; Medeiros, Vanessa P Q; Silva, Keith H D; Dimenstein, Roberto

2006-01-01

Purpose Eggs are a food item of high nutritional value, a source of vitamin A and readily accessible to the general population. Methods This paper analysed the effect of cooking on the retinol levels of free-range and caged hen eggs, using high performance liquid chromatography (HPLC). The retinol levels of hen and quail eggs were also compared. Results The raw egg yolk retinol concentrations of free-range and caged hen eggs were 476.53+/-39.44 and 474.93+/-41.10 microg/100 g and cooked egg yolk concentrations were 393.53+/-24.74 and 379.01+/-30.78 microg/100 g, respectively; quail egg concentration was 636.56+/-32.71 microg retinol/100 g. No significant difference was found between the retinol of free-range and caged hen egg yolks; however, cooking diminished retinol levels, causing a loss of 17 and 20% in the free-range and caged hen egg yolks, respectively. Quail egg retinol concentration was significantly higher than that of the hens. Conclusion The retinol found in 100 g of hen and quail egg yolks could supply around 42 and 70.7% of the vitamin A requirements of an adult man, and is accordingly considered an excellent source of this vitamin.

Enhancement of a stand-alone photovoltaic system's performance: Reduction of soft and hard shading

Energy Technology Data Exchange (ETDEWEB)

Lamont, Lisa A.; El Chaar, Lana [Petroleum Institute, Electrical Engineering Department, P.O. Box 2533, Abu Dhabi (United Arab Emirates)

2011-04-15

A stand-alone photovoltaic (PV) system is the most promising solution to supply electric power to meet energy demand in isolated locations. This technology can offer an interesting alternative to other currently existing sources of energy. Due to space constraint in the remote offshore oil and gas industry, a stand-alone system is used for cathodic protection, telemetry and valve control. However in such an environment, dust accumulation and bird droppings have been critical issues to the operation of off-grid solar devices. These factors do not only reduce the available power of the modules but also makes the cost of solar devices ineffective since cleaning, especially on well-head towers, is very expensive due to the location. Hence this paper presents two technical solutions that have shown promising results in reducing the impact of these factors. (author)

Optimization of the photovoltaic-hydrogen supply system of a stand-alone remote-telecom application

Energy Technology Data Exchange (ETDEWEB)

Gomez, Guillermo; Martinez, Graciano; Galvez, Jose L.; Cuevas, Raquel; Maellas, Jesus [National Institute for Aerospace Technology (INTA), Renewable Energy Department, Ctra. Ajalvir km 4, E-28850 Torrejon de Ardoz, Madrid (Spain); Gila, Raul; Bueno, Emilio [Polytechnical School - Alcala de Henares University, Electronics Department, Campus Universitario, Ctra. De Madrid-Barcelona Km 33.600, Alcala de Henares, Madrid (Spain)

2009-07-15

Hydrogen is considered as the optimal carrier for the surplus energy storage from renewable resources. Although hydrogen and its application in fuel cell is considered as a high-cost energy system, some cost-efficient solutions have been found for their use in stand-alone applications, which usually depend on the variability of renewable sources that have to be oversized in order to reduce their dependence on external energy sources. This paper shows the results from the simulation of several alternatives of introducing hydrogen technologies to increase the independence of a remote-telecom application fed by photovoltaic panels. Hydrogen is obtained by electrolysis and it is used in a fuel cell when the renewable energy source is not enough to maintain the stand-alone application. TRNSYS simulation environment has been used for evaluating the proposed alternatives. The results show that the best configuration option is that considering the use of hydrogen as a way to storage the surplus of radiation and the management system can vary the number of photovoltaic panels assigned to feed the hydrogen generation, the batteries or the telecom application. (author)

A sizing method for stand-alone PV installations with variable demand

Energy Technology Data Exchange (ETDEWEB)

Posadillo, R. [Grupo de Investigacion en Energias y Recursos Renovables, Dpto. de Fisica Aplicada, E.P.S., Universidad de Cordoba, Avda. Menendez Pidal s/n, 14004 Cordoba (Spain); Lopez Luque, R. [Grupo de Investigacion de Fisica Para las Energias y Recursos Renovables, Dpto. de Fisica Aplicada, Edificio C2 Campus de Rabanales, 14071 Cordoba (Spain)

2008-05-15

The practical applicability of the considerations made in a previous paper to characterize energy balances in stand-alone photovoltaic systems (SAPV) is presented. Given that energy balances were characterized based on monthly estimations, the method is appropriate for sizing installations with variable monthly demands and variable monthly panel tilt (for seasonal estimations). The method presented is original in that it is the only method proposed for this type of demand. The method is based on the rational utilization of daily solar radiation distribution functions. When exact mathematical expressions are not available, approximate empirical expressions can be used. The more precise the statistical characterization of the solar radiation on the receiver module, the more precise the sizing method given that the characterization will solely depend on the distribution function of the daily global irradiation on the tilted surface H{sub g{beta}}{sub i}. This method, like previous ones, uses the concept of loss of load probability (LLP) as a parameter to characterize system design and includes information on the standard deviation of this parameter ({sigma}{sub LLP}) as well as two new parameters: annual number of system failures (f) and the standard deviation of annual number of system failures ({sigma}{sub f}). This paper therefore provides an analytical method for evaluating and sizing stand-alone PV systems with variable monthly demand and panel inclination. The sizing method has also been applied in a practical manner. (author)

EFFECTS OF STRAIN, CAGE DENSITY AND POSITION ON IMMUNE RESPONSE TO VACCINES AND BLOOD PARAMETERS IN LAYER PULLETS

Directory of Open Access Journals (Sweden)

Z. BOZKURT

2009-05-01

Full Text Available Two thousand 1-day-old layer chicks were used in the study from Lohman Brown, Isa Brown, Lohman White and Bowans White breeds. The chicks were placed in the at 3 cage densities (211.8, 274.5 and 370.6 cm2 per bird and on 3 positions (as top, middle and bottom tiers. All birds were kept under standard management policy and a commercial vaccination program was practiced. Total specific antibody titres to Infectious Brochitis Virus (IBV, Infectious Bursal Desease Virus (IBDV, Newcastle Disease Virus (NDV and Egg Drop Syndrome Virus (EDSV vaccines at the ages of 5, 10 and 20 weeks were serologically determined by ELISA. Cellmediated immune response was also evaluated. In commercial white egg laying strains specific antibody titres to IBV, IBDV, NDV and EDSV vaccines were greater than in Brown egg layer strains. Keeping in cage created more stress in Brown egg laying chicks than those in white egg laying chicks. As cage density increased, the ratio of heterophils to lymphocytes (H/L ratio slightly increased. Cage position had no influence on the titres of antibodies to IBV and IBDV vaccines but the position of cage in pullets where chicks were stocked, from top to bottom, NDV and EDSV antibody titre decreased and percentage of heterophils, H/L ratio and basophil rates were low. These findings suggest that cage-related stress could be decreased, resistance to diseases and finally well-being of hens may be improved if hens are kept under proper position and density within cage systems with respect to their physiological and behavioral characteristics that controlled by genes.

Motion of Br2 molecules in clathrate cages. A computational study of the dynamic effects on its spectroscopic behavior.

Science.gov (United States)

Bernal-Uruchurtu, M I; Janda, Kenneth C; Hernández-Lamoneda, R

2015-01-22

This work looks into the spectroscopic behavior of bromine molecules trapped in clathrate cages combining different methodologies. We developed a semiempirical quantum mechanical model to incorporate through molecular dynamics trajectories, the effect movement of bromine molecules in clathrate cages has on its absorption spectra. A simple electrostatic model simulating the cage environment around bromine predicts a blue shift in the spectra, in good agreement with the experimental evidence.

Dynamic performance improvement of standalone battery integrated PMSG wind energy system using proportional resonant controller

Directory of Open Access Journals (Sweden)

Dileep Kumar Varma Sagiraju

2017-08-01

Full Text Available The load voltage and frequency should be controlled under steady state and transient conditions in off grid applications. Power quality and power management is very important task for rural communities under erratic wind and load conditions. This paper presents a coordinated Proportional resonant (PR and battery energy controller for enhancement of power quality and power management in direct drive standalone wind energy system. The dynamic performance of standalone direct drive Permanent Magnet Synchronous Generator (PMSG is investigated with the proposed control scheme under various operating conditions such as fluctuating wind with step increase and decrease in wind velocity, balanced and unbalanced load conditions. The proposed PR control strategy with battery energy controller also ensures effective power balance between wind and battery source in order to fulfill the load demand. The superiority of the proposed control strategy is confirmed by comparing with the traditional vector control strategy under fluctuating wind and load conditions through MATLAB/SIMULINK platform.

Self-Assembly in the Ferritin Nano-Cage Protein Superfamily

Directory of Open Access Journals (Sweden)

Yu Zhang

2011-08-01

Full Text Available Protein self-assembly, through specific, high affinity, and geometrically constraining protein-protein interactions, can control and lead to complex cellular nano-structures. Establishing an understanding of the underlying principles that govern protein self-assembly is not only essential to appreciate the fundamental biological functions of these structures, but could also provide a basis for their enhancement for nano-material applications. The ferritins are a superfamily of well studied proteins that self-assemble into hollow cage-like structures which are ubiquitously found in both prokaryotes and eukaryotes. Structural studies have revealed that many members of the ferritin family can self-assemble into nano-cages of two types. Maxi-ferritins form hollow spheres with octahedral symmetry composed of twenty-four monomers. Mini-ferritins, on the other hand, are tetrahedrally symmetric, hollow assemblies composed of twelve monomers. This review will focus on the structure of members of the ferritin superfamily, the mechanism of ferritin self-assembly and the structure-function relations of these proteins.

Multipole induced splitting of metal-cage vibrations in crystalline endohedral D2d-M2@C84 dimetallofullerenes.

Science.gov (United States)

Krause, M; Popov, V N; Inakuma, M; Tagmatarchis, N; Shinohara, H; Georgi, P; Dunsch, L; Kuzmany, H

2004-01-22

Metal-carbon cage vibrations of crystalline endohedral D2d-M2@C84 (M=Sc,Y,Dy) dimetallofullerenes were analyzed by temperature dependent Raman scattering and a dynamical force field model. Three groups of metal-carbon cage modes were found at energies of 35-200 cm(-1) and assigned to metal-cage stretching and deformation vibrations. They exhibit a textbook example for the splitting of molecular vibrations in a crystal field. Induced dipole-dipole and quadrupole-quadrupole interactions account quantitatively for the observed mode splitting. Based on the metal-cage vibrational structure it is demonstrated that D2d-Y2@C84 dimetallofullerene retains a monoclinic crystal structure up to 550 K and undergoes a transition from a disordered to an ordered orientational state at a temperature of approximately 150 K.

Knotting and unknotting proteins in the chaperonin cage: Effects of the excluded volume.

Directory of Open Access Journals (Sweden)

Szymon Niewieczerzal

Full Text Available Molecular dynamics simulations are used to explore the effects of chaperonin-like cages on knotted proteins with very low sequence similarity, different depths of a knot but with a similar fold, and the same type of topology. The investigated proteins are VirC2, DndE and MJ0366 with two depths of a knot. A comprehensive picture how encapsulation influences folding rates is provided based on the analysis of different cage sizes and temperature conditions. Neither of these two effects with regard to knotted proteins has been studied by means of molecular dynamics simulations with coarse-grained structure-based models before. We show that encapsulation in a chaperonin is sufficient to self-tie and untie small knotted proteins (VirC2, DndE, for which the equilibrium process is not accessible in the bulk solvent. Furthermore, we find that encapsulation reduces backtracking that arises from the destabilisation of nucleation sites, smoothing the free energy landscape. However, this effect can also be coupled with temperature rise. Encapsulation facilitates knotting at the early stage of folding and can enhance an alternative folding route. Comparison to unknotted proteins with the same fold shows directly how encapsulation influences the free energy landscape. In addition, we find that as the size of the cage decreases, folding times increase almost exponentially in a certain range of cage sizes, in accordance with confinement theory and experimental data for unknotted proteins.

Design and Operation Studies of A Stand-Alone PV Generation System

DEFF Research Database (Denmark)

Hu, Yanting; Chen, Zhe; Zhang, Donglai

2013-01-01

This paper discusses the modeling, design and operation of a PV powered stand-alone system, which includes a PV array, a battery bank, power electronic converters and the associated control system. The design considerations are analyzed and a design platform is presented. Furthermore the operation...... modes of the system are described. A power electronic system with the associated control scheme has been proposed and simulation models have been developed. Simulation studies have been conducted on an example system; the results have demonstrated the effectiveness of the presented methods....

Discrete-Time Domain Modelling of Voltage Source Inverters in Standalone Applications

DEFF Research Database (Denmark)

Federico, de Bosio; de Sousa Ribeiro, Luiz Antonio; Freijedo Fernandez, Francisco Daniel

2017-01-01

modelling of the LC plant with consideration of delay and sample-and-hold effects on the state feedback cross-coupling decoupling is derived. From this plant formulation, current controllers with wide bandwidth and good relative stability properties are developed. Two controllers based on lead compensation......The decoupling of the capacitor voltage and inductor current has been shown to improve significantly the dynamic performance of voltage source inverters in standalone applications. However, the computation and PWM delays still limit the achievable bandwidth. In this paper a discrete-time domain...

A fully integrated standalone portable cavity ringdown breath acetone analyzer

Science.gov (United States)

Sun, Meixiu; Jiang, Chenyu; Gong, Zhiyong; Zhao, Xiaomeng; Chen, Zhuying; Wang, Zhennan; Kang, Meiling; Li, Yingxin; Wang, Chuji

2015-09-01

Breath analysis is a promising new technique for nonintrusive disease diagnosis and metabolic status monitoring. One challenging issue in using a breath biomarker for potential particular disease screening is to find a quantitative relationship between the concentration of the breath biomarker and clinical diagnostic parameters of the specific disease. In order to address this issue, we need a new instrument that is capable of conducting real-time, online breath analysis with high data throughput, so that a large scale of clinical test (more subjects) can be achieved in a short period of time. In this work, we report a fully integrated, standalone, portable analyzer based on the cavity ringdown spectroscopy technique for near-real time, online breath acetone measurements. The performance of the portable analyzer in measurements of breath acetone was interrogated and validated by using the certificated gas chromatography-mass spectrometry. The results show that this new analyzer is useful for reliable online (online introduction of a breath sample without pre-treatment) breath acetone analysis with high sensitivity (57 ppb) and high data throughput (one data per second). Subsequently, the validated breath analyzer was employed for acetone measurements in 119 human subjects under various situations. The instrument design, packaging, specifications, and future improvements were also described. From an optical ringdown cavity operated by the lab-set electronics reported previously to this fully integrated standalone new instrument, we have enabled a new scientific tool suited for large scales of breath acetone analysis and created an instrument platform that can even be adopted for study of other breath biomarkers by using different lasers and ringdown mirrors covering corresponding spectral fingerprints.

A fully integrated standalone portable cavity ringdown breath acetone analyzer.

Science.gov (United States)

Sun, Meixiu; Jiang, Chenyu; Gong, Zhiyong; Zhao, Xiaomeng; Chen, Zhuying; Wang, Zhennan; Kang, Meiling; Li, Yingxin; Wang, Chuji

2015-09-01

Breath analysis is a promising new technique for nonintrusive disease diagnosis and metabolic status monitoring. One challenging issue in using a breath biomarker for potential particular disease screening is to find a quantitative relationship between the concentration of the breath biomarker and clinical diagnostic parameters of the specific disease. In order to address this issue, we need a new instrument that is capable of conducting real-time, online breath analysis with high data throughput, so that a large scale of clinical test (more subjects) can be achieved in a short period of time. In this work, we report a fully integrated, standalone, portable analyzer based on the cavity ringdown spectroscopy technique for near-real time, online breath acetone measurements. The performance of the portable analyzer in measurements of breath acetone was interrogated and validated by using the certificated gas chromatography-mass spectrometry. The results show that this new analyzer is useful for reliable online (online introduction of a breath sample without pre-treatment) breath acetone analysis with high sensitivity (57 ppb) and high data throughput (one data per second). Subsequently, the validated breath analyzer was employed for acetone measurements in 119 human subjects under various situations. The instrument design, packaging, specifications, and future improvements were also described. From an optical ringdown cavity operated by the lab-set electronics reported previously to this fully integrated standalone new instrument, we have enabled a new scientific tool suited for large scales of breath acetone analysis and created an instrument platform that can even be adopted for study of other breath biomarkers by using different lasers and ringdown mirrors covering corresponding spectral fingerprints.

Spray washing, absorbent cornstarch powder, and dry time to reduce bacterial numbers on soiled transport cage flooring

Science.gov (United States)

Broiler transport cages are often used repeatedly without washing and fecal matter deposited on the floor surface can transfer Campylobacter from one flock to another. Allowing feces to dry is an effective but slow and logistically impractical means to kill Campylobacter in soiled transport cages. ...

Experience with titanium cages in anterior cervical discectomy and fusion

International Nuclear Information System (INIS)

Junaid, M.; Afsheen, A.; Bukhari, S.S.; Rashid, M.U.; Kalsoom, A.

2016-01-01

Background: Anterior cervical discectomy is a common procedure for treating patients for cervical disc prolapse. This study was conducted to study the surgical outcome and demographic characteristics of patients who were treated for anterior cervical disc prolapse. Methods: Study was conducted in the combined military hospital (CMH) Peshawar. Study interval was 3 years from 1st September, 2011 to 31st August, 2014. Total number of patients were 84. Males were 54 (64.28 percentage) and females were 30 (35.71 percentage). All the patients had undergone the procedure of anterior cervical discectomy and fusion with titanium cages (ACDF). All the patients had plain MRI cervical spine done for diagnosis of anterior cervical disc prolapse. Results: Total 84 patients were operated. In the patients who complained of brachialgia, 100 percentage improvement was seen after the operation. Three (3.5 percentage) of the patients, who presented with axial neck pain, continued to complain of pain and 2 (2.5 percentage) of the patients complained of pain at the donor site after the operation. One of the patient had dural tear which resulted in subcutaneous cerebrospinal fluid (CSF) accumulation and was treated conservatively with repeated aspiration. Fusion rate was 100 percentage with titanium cages used for fusion after anterior cervical discectomy. No complications were noted after the surgery at 1 year of interval. Conclusion: Results with titanium cages are expectedly good. Symptoms resolved and fusion rate was 100 percentage at 1 year follow up. (author)

Biomechanical evaluation of an integrated fixation cage during fatigue loading: a human cadaver study.

Science.gov (United States)

Palepu, Vivek; Peck, Jonathan H; Simon, David D; Helgeson, Melvin D; Nagaraja, Srinidhi

2017-04-01

OBJECTIVE Lumbar cages with integrated fixation screws offer a low-profile alternative to a standard cage with anterior supplemental fixation. However, the mechanical stability of integrated fixation cages (IFCs) compared with a cage with anterior plate fixation under fatigue loading has not been investigated. The purpose of this study was to compare the biomechanical stability of a screw-based IFC with a standard cage coupled with that of an anterior plate under fatigue loading. METHODS Eighteen functional spinal units were implanted with either a 4-screw IFC or an anterior plate and cage (AP+C) without integrated fixation. Flexibility testing was conducted in flexion-extension (FE), lateral bending (LB), and axial rotation (AR) on intact spines, immediately after device implantation, and post-fatigue up to 20,000 cycles of FE loading. Stability parameters such as range of motion (ROM) and lax zone (LZ) for each loading mode were compared between the 2 constructs at multiple stages of testing. In addition, construct loosening was quantified by subtracting post-instrumentation ROM from post-fatigue ROM. RESULTS IFC and AP+C configurations exhibited similar stability (ROM and LZ) at every stage of testing in FE (p ≥ 0.33) and LB (p ≥ 0.23) motions. In AR, however, IFCs had decreased ROM compared with AP+C constructs at pre-fatigue (p = 0.07) and at all post-fatigue time points (p ≤ 0.05). LZ followed a trend similar to that of ROM in AR. ROM increased toward intact motion during fatigue cycling for AP+C and IFC implants. IFC specimens remained significantly (p < 0.01) more rigid than specimens in the intact condition during fatigue for each loading mode, whereas AP+C construct motion did not differ significantly (p ≥ 0.37) in FE and LB and was significantly greater (p < 0.01) in AR motion compared with intact specimens after fatigue. Weak to moderate correlations (R 2 ≤ 56%) were observed between T-scores and construct loosening, with lower T

Analysis of Heavy Metal Content (Pb on Waters and Fish at The Floating Cages BPPP Ambon

Directory of Open Access Journals (Sweden)

Wattimena Rachel L.

2018-01-01

Full Text Available Coastal waters play important roles due to highly in natural resources and developing of environmental services. However, there are highly intensity of natural resources utilization, environment and settlement. Consequently, environment and natural resources would be degraded such as in the Ambon Bay. One of the potency at the Ambon Bay is mariculture area namely the floating cages (KJA which belongs to Fisheries education and training (BPPP Ambon. The research aimed to analyze physical-chemical of waters (temperature, pH, salinity and current speed, to analyze heavy metal concentration (Pb on water and fish from floating cages (KJA and to analyze waters pollution status at KJA BPPP Ambon. The average salinity of each floating cage ranged from 30.09 - 30.34°C, pH ranged from 8.03 − 8.44, salinity ranged from 31.36 − 33.34 PSU, and current speed at spring tide ranged from 0.5 – 55.8 Cm/sec while neap tide ranged from 0.1 – 9.8 Cm/sec. Heavy metal concentration (Pb on waters was below the standard for waters quality and the average concentration was 0.002 mg/l. Whilst, the heavy metal concentration (Pb on fishes was below standard for floating cages (floating cages 2-6 which was 0.05 and 0.17mg/l. Otherwise, floating cage 1 had been above maximum standard for fish food and its processing following SNI 7387:2009 (0.3mg/l which was 0.31 mg/l. The status of waters pollution at KJA BPPP Ambon belonged to C class and could be categorized as moderate based on standard for waters quality issued by State Ministerial Decree for the Environment No. 51 Year 2004.

Standalone visualization tool for three-dimensional DRAGON geometrical models

International Nuclear Information System (INIS)

Lukomski, A.; McIntee, B.; Moule, D.; Nichita, E.

2008-01-01

DRAGON is a neutron transport and depletion code able to solve one-, two- and three-dimensional problems. To date DRAGON provides two visualization modules, able to represent respectively two- and three-dimensional geometries. The two-dimensional visualization module generates a postscript file, while the three dimensional visualization module generates a MATLAB M-file with instructions for drawing the tracks in the DRAGON TRACKING data structure, which implicitly provide a representation of the geometry. The current work introduces a new, standalone, tool based on the open-source Visualization Toolkit (VTK) software package which allows the visualization of three-dimensional geometrical models by reading the DRAGON GEOMETRY data structure and generating an axonometric image which can be manipulated interactively by the user. (author)

First attempt to assess the viability of bluefin tuna spawning events in offshore cages located in an a priori favourable larval habitat

Directory of Open Access Journals (Sweden)

Patricia Reglero

2013-10-01

Full Text Available Most of the Atlantic bluefin tuna caught by the purse-seine fleet in the Mediterranean Sea are transferred alive into transport cages and towed to coastal facilities where they are fattened. This major fishery is targeting aggregations of reproductive bluefin tuna that continue spawning within the transport cages. Our study is the first attempt to assess the viability of the spawning events within transport cages placed offshore in a priori favourable locations for larval survival. The study was conducted in June 2010 in the Balearic Sea, a main spawning area for bluefin tuna in the Mediterranean. The location of two transport cages, one with wild and one with captive tuna, coincide with the situation of the chlorophyll front using satellite imagery as a proxy for the salinity front between resident surface waters and those of recent Atlantic origin. The results showed that bluefin tuna eggs were spawned almost every day within the two cages but few or no larvae were found. The expected larval densities estimated after applying mortality curves to the daily egg densities observed in the cages were higher than the sampled larval densities. The trajectories of the eggs after hatching estimated from a particle tracking model based on observed geostrophic currents and a drifter deployed adjacent to the cage suggest that larvae were likely to be caught close to the cages within the sampling dates. Spawning events in captive tuna in transport cages may hatch into larvae though they may experience higher mortality rates than expected in natural populations. The causes of the larval mortality are further discussed in the text. Such studies should be repeated in other spawning areas in the Mediterranean if spawning in cages located offshore in areas favourable a priori for larval survival is likely to be considered a management measurement to minimize the impact of purse-seine fishing on tuna.

ENVIRONMENTAL IMPACT OF FISH FARMING IN FLOATING CAGES IN ISLA ARENA, CAMPECHE

Directory of Open Access Journals (Sweden)

Yadira Silva-Cruz

2011-11-01

Full Text Available Mariculture is the cultivation of marine species of commercial importance. This activity has intensified in recent decades due to the need for food production. The present study evaluated the impact of Rachycentron canadum (Cobia and Sciaenops ocellatus (Red Drum farming in floating cages along the coasts of Campeche, Mexico. The impact of this mariculture system was evaluated through the physicochemical analysis of the sediment from underneath the cages and the analysis of the quality of the water from the farming area. Results showed high concentrations of nitrogen (> 0.5 % and organic matter (> 80 %, both in the farming area and in the control sites. The concentration of fine sediment showed no spatial or temporal changes. There were no detectable concentrations of nitrites, nitrates, ammonium and phosphates in the water, in a range of 0.1 to 100 mg L-1. The impact caused by this farming system appeared to be non significant, at least in the area of study, due to the constant movement of the water caused by ocean currents which, very likely, carried the waste from the cages to other places.

Neural Network based Control of SG based Standalone Generating System with Energy Storage for Power Quality Enhancement

Science.gov (United States)

Nayar, Priya; Singh, Bhim; Mishra, Sukumar

2017-08-01

An artificial intelligence based control algorithm is used in solving power quality problems of a diesel engine driven synchronous generator with automatic voltage regulator and governor based standalone system. A voltage source converter integrated with a battery energy storage system is employed to mitigate the power quality problems. An adaptive neural network based signed regressor control algorithm is used for the estimation of the fundamental component of load currents for control of a standalone system with load leveling as an integral feature. The developed model of the system performs accurately under varying load conditions and provides good dynamic response to the step changes in loads. The real time performance is achieved using MATLAB along with simulink/simpower system toolboxes and results adhere to an IEEE-519 standard for power quality enhancement.

Excess electron is trapped in a large single molecular cage C60F60.

Science.gov (United States)

Wang, Yin-Feng; Li, Zhi-Ru; Wu, Di; Sun, Chia-Chung; Gu, Feng-Long

2010-01-15

A new kind of solvated electron systems, sphere-shaped e(-)@C60F60 (I(h)) and capsule-shaped e(-)@C60F60 (D6h), in contrast to the endohedral complex M@C60, is represented at the B3LYP/6-31G(d) + dBF (diffusive basis functions) density functional theory. It is proven, by examining the singly occupied molecular orbital (SOMO) and the spin density map of e(-)@C60F60, that the excess electron is indeed encapsulated inside the C60F60 cage. The shape of the electron cloud in SOMO matches with the shape of C60F60 cage. These cage-like single molecular solvated electrons have considerably large vertical electron detachment energies VDE of 4.95 (I(h)) and 4.67 eV (D6h) at B3LYP/6-31+G(3df) + dBF level compared to the VDE of 3.2 eV for an electron in bulk water (Coe et al., Int Rev Phys Chem 2001, 20, 33) and that of 3.66 eV for e(-)@C20F20 (Irikura, J Phys Chem A 2008, 112, 983), which shows their higher stability. The VDE of the sphere-shaped e(-)@C60F60 (I(h)) is greater than that of the capsule-shaped e(-)@C60F60 (D6h), indicating that the excess electron prefers to reside in the cage with the higher symmetry to form the more stable solvated electron. It is also noticed that the cage size [7.994 (I(h)), 5.714 and 9.978 A (D6h) in diameter] is much larger than that (2.826 A) of (H2O)20- dodecahedral cluster (Khan, Chem Phys Lett 2005, 401, 85). Copyright 2009 Wiley Periodicals, Inc.

variations in dimensions and shape of thoracic cage with aging

African Journals Online (AJOL)

the rib cage dimensions, the shape and cross- ..... Figure 6: CT axial section of thorax, showing the internal thoracic dimensions and shape at different age .... Dean J, Koehler R, Schleien C, Michael J, Chantarojanasiri T, Rogers M, Traystman ...

A lightweight field cage for a large TPC prototype for the ILC

Energy Technology Data Exchange (ETDEWEB)

Behnke, Ties; Dehmelt, Klaus; Diener, Ralf; Hallermann, Lea; Matsuda, Takeshi; Prahl, Volker; Schade, Peter

2010-06-15

We have developed and constructed the field cage of a prototype Time Projection Chamber for research and development studies for a detector at the International Linear Collider. This prototype has an inner diameter of 72 cm and a length of 61 cm. The design of the field cage wall was optimized for a low material budget of 1.21% of a radiation length and a drift field homogeneity of {delta}E/E

A lightweight field cage for a large TPC prototype for the ILC

International Nuclear Information System (INIS)

Behnke, Ties; Dehmelt, Klaus; Diener, Ralf; Hallermann, Lea; Matsuda, Takeshi; Prahl, Volker; Schade, Peter

2010-06-01

We have developed and constructed the field cage of a prototype Time Projection Chamber for research and development studies for a detector at the International Linear Collider. This prototype has an inner diameter of 72 cm and a length of 61 cm. The design of the field cage wall was optimized for a low material budget of 1.21% of a radiation length and a drift field homogeneity of ΔE/E -4 . Since November 2008 the prototype has been part of a comprehensive test beam setup at DESY and used as a test chamber for the development of Micro Pattern Gas Detector based readout devices. (orig.)

Isolation and characterization of pathogenic Vibrio alginolyticus from sea cage cultured cobia (Rachycentron canadum (Linnaeus 1766)) in India.

Science.gov (United States)

Rameshkumar, P; Nazar, A K A; Pradeep, M A; Kalidas, C; Jayakumar, R; Tamilmani, G; Sakthivel, M; Samal, A K; Sirajudeen, S; Venkatesan, V; Nazeera, B M

2017-11-01

Mass mortalities of cobia, Rachycentron canadum, sub-adults occurred during August 2013 in cage culture in the Gulf of Mannar, Mandapam Tamil Nadu, India. The epizootic of disease was started with typical classical clinical signs followed by acute mortality. Grossly, severe haemorrhage and congestion were observed in the gastric mucosa. The abdomen was distended with peritoneal fluid. The heart revealed haemopericardium and fibrinous pericardium. Histologically, the gastric mucosa showed severe erosion and necrosis. Haemorrhagic pericarditis and an increased size of the melano macrophage centre (MMC) in the tail kidney were other histopathological changes. Vibrio sp. was isolated from the gastric lesions and heart blood swab of moribund fishes and it was found to be virulent to the cobia fingerlings. After the challenge, the same bacterium could be re-isolated from moribund fingerlings. The 16S ribosomal RNA of the isolate was amplified and blast analysis of the sequence confirmed that the pathogen was Vibrio alginolyticus. The confirmation was also correlated with its cultural, biochemical and pathomorphological changes. This is the second report and the first incidence of epizootics with severe pathological lesions in cultured cobia in India. The study throws light on the pathology of vibriosis. By practising cage farm management measures, occurrences of infection may be prevented. The epizootics of vibriosis caused serious economic losses to farmers. Natural blooms of the pathogen can be prevented by sea cage management measures such as, changing the inner net of the cages, changing the location of the cages to relatively clean water (about 50 m apart) from the affected site and providing shade over the cages while the water temperature rises. Supplementation of the feed with immunostimulants and mineral mixture may be practised to improve the immune response against infection. Early diagnosis and sea cage management measures may prevent occurrences of the

Symmetric caging formation for convex polygonal object transportation by multiple mobile robots based on fuzzy sliding mode control.

Science.gov (United States)

Dai, Yanyan; Kim, YoonGu; Wee, SungGil; Lee, DongHa; Lee, SukGyu

2016-01-01

In this paper, the problem of object caging and transporting is considered for multiple mobile robots. With the consideration of minimizing the number of robots and decreasing the rotation of the object, the proper points are calculated and assigned to the multiple mobile robots to allow them to form a symmetric caging formation. The caging formation guarantees that all of the Euclidean distances between any two adjacent robots are smaller than the minimal width of the polygonal object so that the object cannot escape. In order to avoid collision among robots, the parameter of the robots radius is utilized to design the caging formation, and the A⁎ algorithm is used so that mobile robots can move to the proper points. In order to avoid obstacles, the robots and the object are regarded as a rigid body to apply artificial potential field method. The fuzzy sliding mode control method is applied for tracking control of the nonholonomic mobile robots. Finally, the simulation and experimental results show that multiple mobile robots are able to cage and transport the polygonal object to the goal position, avoiding obstacles. Copyright © 2015 ISA. Published by Elsevier Ltd. All rights reserved.

Egg production and welfare of laying hens kept in different housing systems (conventional, enriched cage, and free range).

Science.gov (United States)

Yilmaz Dikmen, B; İpek, A; Şahan, Ü; Petek, M; Sözcü, A

2016-07-01

The aim of this study was to compare egg production performance and welfare traits of laying hens kept in conventional cage (CC), enriched cage (EC), and free range (FR). Lohmann Brown laying hens (n = 480 with 160 per housing type) were studied across a production cycle from placement at 17 wk until depopulation at 66 wk. The hens were randomly allocated into cages or pens of housing system groups; within each system there were four replicates with 40 hens in each pen or cage. The hen day egg production (P = 0.037), feed intake (FI) (P 0.05). The hens in the FR system had additional space for optimum comfort and better feather and bone traits, but the dirty egg ratio, feed consumption, and foot lesions were higher than in CC and EC systems. © 2016 Poultry Science Association Inc.

Assessing mouse behaviour throughout the light/dark cycle using automated in-cage analysis tools.

Science.gov (United States)

Bains, Rasneer S; Wells, Sara; Sillito, Rowland R; Armstrong, J Douglas; Cater, Heather L; Banks, Gareth; Nolan, Patrick M

2018-04-15

An important factor in reducing variability in mouse test outcomes has been to develop assays that can be used for continuous automated home cage assessment. Our experience has shown that this has been most evidenced in long-term assessment of wheel-running activity in mice. Historically, wheel-running in mice and other rodents have been used as a robust assay to determine, with precision, the inherent period of circadian rhythms in mice. Furthermore, this assay has been instrumental in dissecting the molecular genetic basis of mammalian circadian rhythms. In teasing out the elements of this test that have determined its robustness - automated assessment of an unforced behaviour in the home cage over long time intervals - we and others have been investigating whether similar test apparatus could be used to accurately discriminate differences in distinct behavioural parameters in mice. Firstly, using these systems, we explored behaviours in a number of mouse inbred strains to determine whether we could extract biologically meaningful differences. Secondly, we tested a number of relevant mutant lines to determine how discriminative these parameters were. Our findings show that, when compared to conventional out-of-cage phenotyping, a far deeper understanding of mouse mutant phenotype can be established by monitoring behaviour in the home cage over one or more light:dark cycles. Copyright © 2017 The Author(s). Published by Elsevier B.V. All rights reserved.

Theoretical study on the cage-like nanostructures formed by amino acids and their potential applications as drug carriers

Science.gov (United States)

Weng, Pei Pei; Fan, Jian Fen; Lin, Hui Fang; Zhao, Xin; Si, Xia Lan

2017-12-01

The cage-like octamer, decamer and dodecamer constructed from aspartic acid monomers have been studied to explore their potential applications as drug carriers using the density functional theory. The calculation results indicate that these stable cage-like oligomers are mainly connected by the -C=O…HOOC- and -HN…HOOC- H-bonds and still keep stability and good drum-shaped topologies after the incorporation of 5-fluorouracil, paraldehyde and C24, respectively. The self-assembled cage-like oligomers may be applied to the preparation of new biological materials and the design of drug delivery systems.

Simulation of potential standalone liquid desiccant cooling cycles

International Nuclear Information System (INIS)

Das, Rajat Subhra; Jain, Sanjeev

2015-01-01

LDCS (Liquid desiccant cooling systems), capable of achieving dehumidification and cooling with low-grade heat input, can be effectively used for treating fresh air in hot and humid regions. These can also be operated using non-concentrating solar collectors. The present study is concerned with the evaluation of various potential liquid desiccant cycles for tropical climatic conditions. Six potential standalone liquid desiccant cycles are identified and analyzed to select the best configuration for achieving thermal comfort. A computer simulation model is developed in EES (Equation Solver) software platform to evaluate the performance of all the cycles at various operating conditions. Aqueous solution of LiCl (lithium chloride) is used as desiccant. Mass and energy balance equations of all the components along with their effectiveness and LiCl property correlation equations are solved simultaneously for given ambient conditions. As the desiccant circuit is a closed loop, no assumptions are made about its concentration and temperature in the algorithm. Supply air conditions, cooling capacity, COP (capacity and coefficient of performance) and CR (circulation rate) per unit cooling capacity and hot water temperature requirement are used as a measure for analyzing the performance of the different cycles. The effect of hot water temperature on the performance of the cycles is evaluated at ARI conditions. The performances of the cycles are also evaluated for cities selected from each of the climatic zone of India that represent typical tropical climates. Although all the cycles are feasible at ARI and hot and dry conditions, only two cycles can achieve the selected indoor conditions in the peak humid conditions. The results would be useful for selecting suitable liquid desiccant cycle for a given climate. - Highlights: • Six potential standalone liquid desiccant cycles identified and analyzed to select best configuration. • A computer simulation model is developed in

Automated Operant Conditioning in the Mouse Home Cage.

Science.gov (United States)

Francis, Nikolas A; Kanold, Patrick O

2017-01-01

Recent advances in neuroimaging and genetics have made mice an advantageous animal model for studying the neurophysiology of sensation, cognition, and locomotion. A key benefit of mice is that they provide a large population of test subjects for behavioral screening. Reflex-based assays of hearing in mice, such as the widely used acoustic startle response, are less accurate than operant conditioning in measuring auditory processing. To date, however, there are few cost-effective options for scalable operant conditioning systems. Here, we describe a new system for automated operant conditioning, the Psibox. It is assembled from low cost parts, designed to fit within typical commercial wire-top cages, and allows large numbers of mice to train independently in their home cages on positive reinforcement tasks. We found that groups of mice trained together learned to accurately detect sounds within 2 weeks of training. In addition, individual mice isolated from groups also showed good task performance. The Psibox facilitates high-throughput testing of sensory, motor, and cognitive skills in mice, and provides a readily available animal population for studies ranging from experience-dependent neural plasticity to rodent models of mental disorders.

Mating competitiveness of male Anopheles arabiensis mosquitoes irradiated with a partially or fully sterilizing dose in small and large laboratory cages.

Science.gov (United States)

Helinski, M E H; Knols, B G J

2008-07-01

Male mating competitiveness is a crucial parameter in many genetic control programs including the sterile insect technique (SIT). We evaluated competitiveness of male Anopheles arabiensis Patton as a function of three experimental variables: (1) small or large cages for mating, (2) the effects of either a partially sterilizing (70 Gy) or fully sterilizing (120 Gy) dose, and (3) pupal or adult irradiation. Irradiated males competed for females with an equal number of unirradiated males. Competitiveness was determined by measuring hatch rates of individually laid egg batches. In small cages, pupal irradiation with the high dose resulted in the lowest competitiveness, whereas adult irradiation with the low dose gave the highest, with the latter males being equal in competitiveness to unirradiated males. In the large cage, reduced competitiveness of males irradiated in the pupal stage was more pronounced compared with the small cage; the males irradiated as adults at both doses performed similarly to unirradiated males. Unexpectedly, males irradiated with the high dose performed better in a large cage than in a small one. A high proportion of intermediate hatch rates was observed for eggs collected in the large cage experiments with males irradiated at the pupal stage. It is concluded that irradiation of adult An. arabiensis with the partially sterilizing dose results in the highest competitiveness for both cage designs. Cage size affected competitiveness for some treatments; therefore, competitiveness determined in laboratory experiments must be confirmed by releases into simulated field conditions. The protocols described are readily transferable to evaluate male competitiveness for other genetic control techniques.

Theory of nanotube faraday cage

Science.gov (United States)

Roxana Margine, Elena; Nisoli, Cristiano; Kolmogorov, Aleksey; Crespi, Vincent H.

2003-03-01

Charge transfer between dopants and double-wall carbon nanotubes is examined theoretically. We model the system as a triple cylindrical capacitor with the dopants forming a shell around the outer wall of the nanotube. The total energy of the system contains three terms: the band structure energies of the inner and outer tube, calculated in a tight-binding model with rigid bands, and the electrostatic energy of the tri-layer distribution. Even for metallic inner and outer tube walls, wherein the diameter dependence of the bandgap does not favor the outer wall, nearly all of the dopant charge resides on the outer layer, a nanometer-scale Faraday cage. The calculated charge distribution is in agreement with recent experimental measurements.

Artificial marine habitats favour a single fish species on a long-term scale: the dominance of Boops boops around off-shore fish cages

Directory of Open Access Journals (Sweden)

Rodrigo Riera

2014-12-01

Full Text Available Off-shore fish cages are new artificial habitats that can affect pelagic fish assemblages and constitute an important food source for wild fish assemblages. This aggregation has noticeable ecological consequences in cage areas in impoverished ecosystems such as those in the Canary archipelago (NE Atlantic Ocean. However, this new habitat could be dominated by a single species, reducing its positive ecological effects. Wild fish assemblages associated with an off-shore fish lease on the northeastern coast of Tenerife (Canary Islands were sampled for six years. Fish assemblage structure beneath fish cages and at controls ( > 500 m from cages differed significantly between locations, with 13 times greater abundance at cage locations. These differences were mainly explained by the dominance of bogue (Boops boops around fish cages. This trend was consistent in the long-term throughout the study period (2004-2009, affecting local fisheries. The presence of fish cages significantly altered wild fish assemblages in the study area, enhancing mainly biomass and abundance of one species, bogue, and causing shifts in species composition.

Slotted cage resonator for high-field magnetic resonance imaging of rodents

Energy Technology Data Exchange (ETDEWEB)

Marrufo, O; Vasquez, F; Solis, S E; Rodriguez, A O, E-mail: arog@xanum.uam.mx [Departamento de Ingenieria Electrica, Universidad Autonoma Metropolitana Iztapalapa, Mexico, DF 09340 (Mexico)

2011-04-20

A variation of the high-frequency cavity resonator coil was experimentally developed according to the theoretical frame proposed by Mansfield in 1990. Circular slots were used instead of cavities to form the coil endplates and it was called the slotted cage resonator coil. The theoretical principles were validated via a coil equivalent circuit and also experimentally with a coil prototype. The radio frequency magnetic field, B1, produced by several coil configurations was numerically simulated using the finite-element approach to investigate their performances. A transceiver coil, 8 cm long and 7.6 cm in diameter, and composed of 4 circular slots with a 15 mm diameter on both endplates, was built to operate at 300 MHz and quadrature driven. Experimental results obtained with the slotted cage resonator coil were presented and showed very good agreement with the theoretical expectations for the resonant frequency as a function of the coil dimensions and slots. A standard birdcage coil was also built for performance comparison purposes. Phantom images were then acquired to compute the signal-to-noise ratio of both coils showing an important improvement of the slotted cage coil over the birdcage coil. The whole-body images of the mouse were also obtained showing high-quality images. Volume resonator coils can be reliably built following the physical principles of the cavity resonator design for high-field magnetic resonance imaging applications of rodents.

The Iron Cage and the Gaze: Interpreting Medical Control in the English Health System

Directory of Open Access Journals (Sweden)

Mark Exworthy

2015-05-01

Full Text Available This paper seeks to determine the value of theoretical ideal-types of medical control. Whilst ideal types (such as the iron cage and gaze need revision in their application to medical settings, they remain useful in describing and explaining patterns of control and autonomy in the medical profession. The apparent transition from the cage to the gaze has often been over-stated since both types are found in many contemporary health reforms. Indeed, forms of neo-bureaucracy have emerged alongside surveillance of the gaze. These types are contextualised and elaborated in terms of two empirical examples: the management of medical performance and financial incentives for senior hospital doctors in England. Findings point towards the reformulation of medical control, an on-going re-stratification of the medical profession, and the internalisation of managerial discourses. The cumulative effect involves the medical profession’s ability to re-cast and enhance its position (vis-à-vis managerial interests.Keywords: medical profession, medical control, iron cage, gaze

Energy-bounded caging: Formal definition and 2-D energy lower bound algorithm based on weighted alpha shapes

NARCIS (Netherlands)

Mahler, Jeffrey; Pokorny, Florian T.; McCarthy, Zoe; van der Stappen, A.F.; Goldberg, Ken

Caging grasps are valuable as they can be robust to bounded variations in object shape and pose, do not depend on friction, and enable transport of an object without full immobilization. Complete caging of an object is useful but may not be necessary in cases where forces such as gravity are

Nicolas Cage otsib kadunud tütart naistesaarelt / Triin Tael

Index Scriptorium Estoniae

Tael, Triin

2006-01-01

Õudusfilm "Ohvripidu" : režissöör Neil LaBute : peaosas Nicholas Cage : Ameerika Ühendriigid - Saksamaa 2006. Film on uusversioon briti 1973.a. filmist, mille režissöör oli Robin Hardy ja ühes peaosadest Christopher Lee

Passive cooling of standalone flat PV module with cotton wick structures

International Nuclear Information System (INIS)

Chandrasekar, M.; Suresh, S.; Senthilkumar, T.; Ganesh karthikeyan, M.

2013-01-01

Highlights: • A simple passive cooling system is developed for standalone flat PV modules. • 30% Reduction in module temperature is observed with developed cooling system. • 15.61% Increase in output power of PV module is found with developed cooling system. • Module efficiency is increased by 1.4% with cooling arrangement. • Lower thermal degradation due to narrow range of temperature characteristics. - Abstract: In common, PV module converts only 4–17% of the incoming solar radiation into electricity. Thus more than 50% of the incident solar energy is converted as heat and the temperature of PV module is increased. The increase in module temperature in turn decreases the electrical yield and efficiency of the module with a permanent structural damage of the module due to prolonged period of thermal stress (also known as thermal degradation of the module). An effective way of improving efficiency and reducing the rate of thermal degradation of a PV module is to reduce the operating temperature of PV module. This can be achieved by cooling the PV module during operation. Hence in the present work, a simple passive cooling system with cotton wick structures is developed for standalone flat PV modules. The thermal and electrical performance of flat PV module with cooling system consisting of cotton wick structures in combination with water, Al 2 O 3 /water nanofluid and CuO/water nanofluid are investigated experimentally. The experimental results are also compared with the thermal and electrical performance of flat PV module without cooling system

Prevalência de CAGE positivo entre estudantes de segundo grau de Porto Alegre, Rio Grande do Sul, Brasil, 1994 Prevalence of CAGE-positive secondary school students in Porto Alegre, Rio Grande do Sul, Brazil, 1994

Directory of Open Access Journals (Sweden)

Clarissa C. Trois

1997-09-01

Full Text Available Este estudo objetiva descrever a prevalência de positividade do teste CAGE entre estudantes de terceiro ano do segundo grau de Porto Alegre, RS, em 1994. A amostra foi composta por 1.171 estudantes, 598 (51% procedentes de escolas públicas e 573 (49% de escolas particulares. Encontrou-se referência de consumo prévio de bebidas alcoólicas de 93%, com maior prevalência entre os estudantes do sexo masculino (pThis study aims to describe the prevalence of CAGE-positive third-year high school students in Porto Alegre, Rio Grande do Sul, in 1994. The sample consisted of 1,171 students: 598 (51% from public and 573 (49% from private schools. We found reference to previous alcoholic beverage consumption in 93% of the interviewees. The highest prevalence was among male students (p<0.02 and students from private schools (p<0.03. Half of the students reported weekly consumption, usually when going to parties (60% and bars (17%. CAGE positiveness prevalence was 8.3% overall and 11% among males (p<0.02. When variables like gender, age, and socioeconomic status were controlled, there was no statistically significant difference between the kind of school and CAGE status.

Optimal expansion planning of stand-alone systems with stochastic simulations

Energy Technology Data Exchange (ETDEWEB)

Hoese, Alejandro [Instituto de Energia Electrica (IEE), Universidad Nacional de San Juan, (Argentina)

1997-12-31

Stand-alone systems in the range of 1 kW - 10 MW are taking relevance in the new (global) liberal concept of energy market. State and private investors are becoming increasingly attention on the use of renewable for these systems, but it must be shown that these non-conventional solutions are competitive with the established conventional ones. The high investment costs and the technical and economic uncertainties coupled with the use of time-dependent energy sources are the mainly inhibiting factors for the decision agents to choose these systems instead of conventional ones. In the paper a new model for optimal expansion planning of hybrid stand-alone generating systems under consideration of uncertainties is presented. This model is at present in {sup d}evelopment state{sup .} Results already obtained in the first steps of this research are promising and some of them are here presented. [Espanol] Los sistemas autocontenidos en el rango de 1 Kw a 10 MW estan tomando importancia en el nuevo (global) concepto liberal del mercado de la energia. Inversionistas privados y del Estado estan poniendo mayor atencion en el uso de energias renovables para estos sistemas, pero debe mostrarse que estas soluciones no-convencionales son competitivas con las convencionales establecidas. Los altos costos de inversion y las incertidumbres tecnicas y economicas aunadamente con el uso de fuentes de energia dependientes del tiempo son los principales factores inhibidores de los factores de decision para escoger estos sistemas en lugar de los convencionales. En este articulo se presenta un nuevo modelo de planeacion de expansion optima de sistemas hibridos autocontenidos de generacion electrica bajo la consideracion de incertidumbres. Este modelo esta actualmente en {sup e}stado de desarrollo{sup .} Los resultados ya obtenidos en las primeras etapas de esta investigacion son prometedores y se presentan algunos de ellos.

Optimal expansion planning of stand-alone systems with stochastic simulations

Energy Technology Data Exchange (ETDEWEB)

Hoese, Alejandro [Instituto de Energia Electrica (IEE), Universidad Nacional de San Juan, (Argentina)

1998-12-31

Stand-alone systems in the range of 1 kW - 10 MW are taking relevance in the new (global) liberal concept of energy market. State and private investors are becoming increasingly attention on the use of renewable for these systems, but it must be shown that these non-conventional solutions are competitive with the established conventional ones. The high investment costs and the technical and economic uncertainties coupled with the use of time-dependent energy sources are the mainly inhibiting factors for the decision agents to choose these systems instead of conventional ones. In the paper a new model for optimal expansion planning of hybrid stand-alone generating systems under consideration of uncertainties is presented. This model is at present in {sup d}evelopment state{sup .} Results already obtained in the first steps of this research are promising and some of them are here presented. [Espanol] Los sistemas autocontenidos en el rango de 1 Kw a 10 MW estan tomando importancia en el nuevo (global) concepto liberal del mercado de la energia. Inversionistas privados y del Estado estan poniendo mayor atencion en el uso de energias renovables para estos sistemas, pero debe mostrarse que estas soluciones no-convencionales son competitivas con las convencionales establecidas. Los altos costos de inversion y las incertidumbres tecnicas y economicas aunadamente con el uso de fuentes de energia dependientes del tiempo son los principales factores inhibidores de los factores de decision para escoger estos sistemas en lugar de los convencionales. En este articulo se presenta un nuevo modelo de planeacion de expansion optima de sistemas hibridos autocontenidos de generacion electrica bajo la consideracion de incertidumbres. Este modelo esta actualmente en {sup e}stado de desarrollo{sup .} Los resultados ya obtenidos en las primeras etapas de esta investigacion son prometedores y se presentan algunos de ellos.

Universal CAGE-WANT Questionnaire: “Think & Fill in the Suspect, Self-Assess and Screen! You May Need Help For, What You Have Filled In!”

Directory of Open Access Journals (Sweden)

Deepak Gupta

2014-12-01

Full Text Available In 1970, John A. Ewing [1] developed CAGE questionnaire for identifying hidden alcoholism. It has been almost a half-century since 1970s [2] and CAGE questionnaire has expanded its promise and utility in identifying other addictions like for drug use as CAGE-AID in 1990s [3] and for personal electronic devices as University of Rochester Modified CAGE Questions in 2010s [4]. It seems the time is ripe to document a Universal CAGE Questionnaire (Table 1: Universal CAGE-WANT Questionnaire wherein any and every subject of fascination and/or any and every human urge to WANT can be incorporated for self-assessment and/or screening to identify addiction for the suspected and tested WANT.

Evaluating a Pre-session Exercise in a Standalone Information Literacy Class

Directory of Open Access Journals (Sweden)

Joseph E. Goetz

2015-12-01

Full Text Available In this study, researchers evaluate a homework exercise assigned before a standalone information literacy session. Students in a Master of Education program completed a worksheet using the ERIC database thesaurus. The researchers conducted pre- and posttests within a single library session to assess student learning, using a control group for comparison. The treatment group did not demonstrate better thesaurus skills than students who had regular library instruction alone, but results pointed the way to targeted improvements of pre-session learning materials. This approach could inform other information literacy homework applications such as flipping the classroom.

Design of Stand-Alone Hybrid Power Generation System at Brumbun Beach Tulungagung East Java

Science.gov (United States)

Rahmat, A. N.; Hidayat, M. N.; Ronilaya, F.; Setiawan, A.

2018-04-01

Indonesian government insists to optimize the use of renewable energy resources in electricity generation. One of the efforts is launching Independent Energy Village plan. This program aims to fulfill the need of electricity for isolated or remote villages in Indonesia. In order to support the penetration of renewable energy resources in electricity generation, a hybrid power generation system is developed. The simulation in this research is based on the availability of renewable energy resources in Brumbun beach, Tulungagung, East Java. Initially, the electricity was supplied through stand-alone electricity generations which are installed at each house. Hence, the use of electricity between 5 p.m. – 9 p.m. requires high operational costs. Based on the problem above, this research is conducted to design a stand-alone hybrid electricity generation system, which may consist of diesel, wind, and photovoltaic. The design is done by using HOMER software to optimize the use of electricity from renewable resources and to reduce the operation of diesel generation. The combination of renewable energy resources in electricity generation resulted in NPC of 44.680, COE of 0,268, and CO2 emissions of 0,038 % much lower than the use of diesel generator only.

Feasibility and Optimal Design of a Stand-Alone Photovoltaic Energy System for the Orphanage

Directory of Open Access Journals (Sweden)

Vincent Anayochukwu Ani

2014-01-01

Full Text Available Access to electricity can have a positive psychological impact through a lessening of the sense of exclusion, and vulnerability often felt by the orphanages. This paper presented the simulation and optimization study of a stand-alone photovoltaic power system that produced the desired power needs of an orphanage. Solar resources for the design of the system were obtained from the National Aeronautics and Space Administration (NASA Surface Meteorology and Solar Energy website at a location of 6°51′N latitude and 7°35′E longitude, with annual average solar radiation of 4.92 kWh/m2/d. This study is based on modeling, simulation, and optimization of energy system in the orphanage. The patterns of load consumption within the orphanage were studied and suitably modeled for optimization. Hybrid Optimization Model for Electric Renewables (HOMER software was used to analyze and design the proposed stand-alone photovoltaic power system model. The model was designed to provide an optimal system configuration based on an hour-by-hour data for energy availability and demands. A detailed design, description, and expected performance of the system were presented in this paper.

A Cage-Based Training System for Non-Human Primates

Directory of Open Access Journals (Sweden)

Michaela D Curry

2017-07-01

Full Text Available Non-human primates (NHPs are widely-used experimental models in neurophysiological studies. Training on cognitive tasks prior to collecting neurophysiological data is an inseparable part of much of the research conducted using NHPs. Any improvement in the training method that reduces stress to the animal, increases the speed of training or improves performance on the task is of great potential value. We have designed, built and successfully utilized a fully portable cage-mountable system to train rhesus monkeys (Macaca mulatta. The flexibility and portability of both the animal interface and the control unit of this system would allow it to be used for a large variety of behavioral paradigms. Aside from experimental use, our system could potentially be used as a source of animal enrichment. We present the behavioral data collected using this method to train a visual working memory and a change detection task. Utilizing the in-cage training system allows the animal greater control over when and how long it chooses to work, rather than imposing a training schedule based on the availability of the experimenter. Using this method the animal learned to perform both behavioral tasks in a short amount of time. In some cases the animal would use the training system without the need for any water restriction. In addition to allowing voluntary, self-paced engagement with the task, this method has the advantage of being less disruptive to the monkey's social interactions, and presumably eliminating some of the stress occasioned by relocating for chair training. Although this system has the potential to ease and expedite the behavioral training of NHPs on a variety of tasks, here we provide only a demonstration of our cage-based training system using one NHP.

Laparoscopic hand-assisted versus robotic-assisted laparoscopic sleeve gastrectomy: experience of 103 consecutive cases.

Science.gov (United States)

Kannan, Umashankkar; Ecker, Brett L; Choudhury, Rashikh; Dempsey, Daniel T; Williams, Noel N; Dumon, Kristoffel R

2016-01-01

Laparoscopic sleeve gastrectomy has become a stand-alone procedure in the treatment of morbid obesity. There are very few reports on the use of robotic approach in sleeve gastrectomy. The purpose of this retrospective study is to report our early experience of robotic-assisted laparoscopic sleeve gastrectomy (RALSG) using a proctored training model with comparison to an institutional cohort of patients who underwent laparoscopic hand-assisted sleeve gastrectomy (LASG). University hospital. The study included 108 patients who underwent sleeve gastrectomy either via the laparoscopic-assisted or robot-assisted approach during the study period. Of these 108 patients, 62 underwent LASG and 46 underwent RALSG. The console surgeon in the RALSG is a clinical year 4 (CY4) surgery resident. All CY4 surgery residents received targeted simulation training before their rotation. The console surgeon is proctored by the primary surgeon with assistance as needed by the second surgeon. The patients in the robotic and laparoscopic cohorts did not have a statistical difference in their demographic characteristics, preoperative co-morbidities, or complications. The mean operating time did not differ significantly between the 2 cohorts (121 min versus 110 min, P = .07). Patient follow-up in the LSG and RALSG were 91% and 90% at 3 months, 62% and 64% at 6 months, and 60% and 55% at 1 year, respectively. The mean percentage estimated weight loss (EWL%) at 3 months, 6 months, and 1 year was greater in the robotic group but not statistically significant (27 versus 22 at 3 mo [P = .05] and 39 versus 34 at 6 mo [P = .025], 57 versus 48 at 1 yr [P = .09]). There was no mortality in either group. Early results of our experience with RALSG indicate low perioperative complication rates and comparable weight loss with LASG. The concept of a stepwise education model needs further validation with larger studies. Copyright © 2016 American Society for Bariatric Surgery. Published by Elsevier Inc

In situ experiments to assess effects of constraints linked to caging on ecotoxicity biomarkers of the three-spined stickleback (Gasterosteus aculeatus L.).

Science.gov (United States)

Le Guernic, Antoine; Sanchez, Wilfried; Palluel, Olivier; Bado-Nilles, Anne; Turies, Cyril; Chadili, Edith; Cavalié, Isabelle; Adam-Guillermin, Christelle; Porcher, Jean-Marc; Geffard, Alain; Betoulle, Stéphane; Gagnaire, Béatrice

2016-04-01

The aim of this study was to evaluate the effects of caging constraints on multiple fish biomarkers used during ecotoxicological studies (biometric data, immune and antioxidant systems, and energetic status). Two of these constraints were linked to caging: starvation and fish density in cages, and one in relation to the post-caging handling: a short transport. Three in situ experiments were conducted with three-spined sticklebacks (Gasterosteus aculeatus). The first experiment compared the effects of three densities (low, medium, and high). The second experiment compared effects of starvation in fish fed every two days with fish that were not fed. Finally comparisons between sticklebacks which have suffered a short car transport after caging and sticklebacks killed without preliminary transport were made. The lack of food had no effect on fish energetic reserves but negatively affected their condition index and their immune system. Transport and high density induced oxidative stress, defined as an overproduction of reactive oxygen species and a stimulation of the antioxidant system. These two constraints also harmed the leucocyte viability. In order not to have any impact on ecotoxicity biomarkers during in situ experiments, it is preferable to decrease fish density in cages, prevent transport before dissections, and feed fish when the caging lasts more than two weeks.

Gender differences in exerted forces and physiological load during pushing and pulling of wheeled cages by postal workers

NARCIS (Netherlands)

Van Der Beek, Allard J.; Kluver, B.D.R.; Frings-Dresen, M. H. W.; Hoozemans, M. J M

The aim was to determine gender differences regarding exerted forces and physiological load during push/pull tasks simulating the daily working practice of postal workers. Eight female and four male workers handled four-wheeled cages under eight conditions corresponding to the cage weight (130, 250,

Assessment of the Usability of the Workbench Faraday Cage Method

DEFF Research Database (Denmark)

Sørensen, Morten; Franek, Ondrej; Christensen, Søren K.

2011-01-01

The workbench Faraday Cage method (WBFC) is a time efficient module pre-compliance test regarding radiated emission. This work investigates the method’s usability and credibility and concludes that for this particular case the WBFC perform a tolerable compliance test for frequencies below 360 MHz...

Size optimization of stand-alone photovoltaic (PV) room air conditioners

International Nuclear Information System (INIS)

Chen, Chien-Wei; Zahedi, A.

2006-01-01

Sizing of a stand-alone PV system determines the main cost of the system. PV electricity cost is determined by the amount of solar energy received, hence the actual climate and weather conditions such as solar irradiance and ambient temperature affect the size required and cost of the system. Air conditioning demand also depends on the weather conditions. Therefore, sizing a PV powered air conditioner must consider the characteristics of local climate and temperature. In this paper, sizing procedures and special considerations for air conditioning under Melbourne's climatic conditions is presented. The reliability of various PV-battery size combinations is simulated by MATLAB. As a result, excellent system performance can be predicated.(Author)

Comparing alternative methods for holding virgin honey bee queens for one week in mailing cages before mating.

Directory of Open Access Journals (Sweden)

Gianluigi Bigio

Full Text Available In beekeeping, queen honey bees are often temporarily kept alive in cages. We determined the survival of newly-emerged virgin honey bee queens every day for seven days in an experiment that simultaneously investigated three factors: queen cage type (wooden three-hole or plastic, attendant workers (present or absent and food type (sugar candy, honey, or both. Ten queens were tested in each of the 12 combinations. Queens were reared using standard beekeeping methods (Doolittle/grafting and emerged from their cells into vials held in an incubator at 34C. All 12 combinations gave high survival (90 or 100% for three days but only one method (wooden cage, with attendants, honey gave 100% survival to day seven. Factors affecting queen survival were analysed. Across all combinations, attendant bees significantly increased survival (18% vs. 53%, p<0.001. In addition, there was an interaction between food type and cage type (p<0.001 with the honey and plastic cage combination giving reduced survival. An additional group of queens was reared and held for seven days using the best method, and then directly introduced using smoke into queenless nucleus colonies that had been dequeened five days previously. Acceptance was high (80%, 8/10 showing that this combination is also suitable for preparing queens for introduction into colonies. Having a simple method for keeping newly-emerged virgin queens alive in cages for one week and acceptable for introduction into queenless colonies will be useful in honey bee breeding. In particular, it facilitates the screening of many queens for genetic or phenotypic characteristics when only a small proportion meets the desired criteria. These can then be introduced into queenless hives for natural mating or insemination, both of which take place when queens are one week old.

Distance Factors and Croatian Export Obstacles in the EU15: CAGE Approach

Directory of Open Access Journals (Sweden)

Helena Miloloža

2015-07-01

Full Text Available For long-term sustainability of any enterprise, it is required to observe each market separately and systematically modify business approach to prevailing conditions in each. However, adaptation to each market can be a complex affair that requires certain financial costs but ignoring distinguishing criteria leads to reduction in revenues and undermines long-term profitability. Time saving and cost-effectiveness can be achieved by application of The CAGE Distance Framework – a model that analysis all diversities between two or more countries. Croatia did not yet utilize the benefits that European Union membership provides nor did significantly improved its international business. It is obvious that Croatia faces difficulties in the strategic approach to prospective foreign markets. Therefore, emphasis of this article is on analysis and identification of the distinguishing factors between Croatia and the EU15 in order to facilitate and enhance cooperation among them in the future. Throughout the analysis of Croatian export from the beginning of the economic crisis, this article gives an overview of international collaboration among Croatia and the EU15 and comparative analysis by using The CAGE Distance Framework. This analysis has confirmed significant fluctuations, unexploited potential and problems of the Croatian economy in all dimensions of The CAGE model.

HeliscopeCAGE sequencing, Delve mapping and CAGE TSS aggregation - FANTOM5 | LSDB Archive [Life Science Database Archive metadata

Lifescience Database Archive (English)

Full Text Available switchLanguage; BLAST Search Image Search Home About Archive Update History Data List Contact us FANTOM...at) Data file File name: fantom5_new_experimental_details.zip File URL: ftp://ftp.biosciencedbc.jp/archive/fantom5/LATEST/fantom...osciencedbc.jp/archive/fantom5/datafiles/LATEST/basic/ File size: 2.5 TB Simple s...earch URL http://togodb.biosciencedbc.jp/togodb/view/fantom5_new_experimental_details#en Data acquisition me...thod - Data analysis method HeliScopeCAGE ( http://fantom.gsc.riken.jp/protocols/heliscope.html ) Delve (Ali

Use of protein cages as a template for confined synthesis of inorganic and organic nanoparticles.

Science.gov (United States)

Uchida, Masaki; Qazi, Shefah; Edwards, Ethan; Douglas, Trevor

2015-01-01

Protein cages are hollow spherical proteins assembled from a defined number of subunits. Because they are extremely homogeneous in size and structure, their interior cavities can serve as ideal templates to encapsulate and synthesize well-defined nanoparticles. Here, we describe the exemplary synthesis of a hard and a soft material in two representative protein cages, i.e., magnetite nanoparticles in ferritin and a poly(2-aminoethyl)methacrylate inside a viral capsid derived from the bacteriophage P22.

Thermal Degradation Mechanism of a Thermostable Polyester Stabilized with an Open-Cage Oligomeric Silsesquioxane

Directory of Open Access Journals (Sweden)

Yolanda Bautista

2017-12-01

Full Text Available A polyester composite was prepared through the polymerization of an unsaturated ester resin with styrene and an open-cage oligomeric silsesquioxane with methacrylate groups. The effect of the open-cage oligomeric silsesquioxane on the thermal stability of the thermostable polyester was studied using both thermogravimetric analysis and differential thermal analysis. The results showed that the methacryl oligomeric silsesquioxane improved the thermal stability of the polyester. The decomposition mechanism of the polyester/oligomer silsesquioxane composite was proposed by Fourier transform infrared spectroscopy (FTIR analysis of the volatiles.

PRODUCTIVITY OF LAYERS AND EGG QUALITY IN FREE RANGE AND CAGE SYSTEM OF HOUSING

OpenAIRE

Đ. Senčić; Danijela Butko

2006-01-01

The research was conducted with two groups of Lohmann Brown hybrid layers. Production of eggs lasted for 52 weeks. A control group of layers was kept in the conventional housing system, that is, in cages, while experimental group was kept in the free range system. Layers from the free range system, compared to those kept in cages, laid fewer eggs, (266:295), they consumed more feed on daily basis (129 g : 115 g), more feed per kilogram of egg weight (2.83 kg : 2.35 kg), they had higher mor...

Hen genetic strain and extended cold storage influence on physical egg quality from cage-free aviary housing system.

Science.gov (United States)

Jones, D R; Karcher, D M; Regmi, P; Robison, C O; Gast, R K

2018-04-02

In the United States, there is an increase in need for cage-free eggs in retail and food manufacturing sectors. Understanding the impact of cage-free systems and the corresponding management on egg quality is pertinent as the U.S. industry adapts existing housing and builds new cage-free housing structures. A study was conducted comparing 2 brown shell and 2 white shell hen strains housed in a cage-free aviary system. Each set of eggs were placed in cold storage and assessed at 0, 2, 4, 8, and 12 wk. Eggs were collected at 21, 31, 42, and 60 wk of hen age. A full profile of physical quality measurements was conducted on up to 18 intact eggs for each hen strain/egg storage/hen age combination. Egg weight increased approximately 10 g for brown shell and 14 g for white shell eggs as hens aged. Many of the properties monitored were significantly impacted by all 3 main effects (hen strain, egg storage, and hen age) resulting in 3-way interactions. A brown and a white shell strain had stronger shells (44 N; P study also determined volume of shell, total length, maximum width, and percent length at maximum width to more accurately indicate egg shape than shape index. One brown shell strain produced eggs with the most consistent shape characteristics over the hen ages monitored. White shell eggs from the cage-free aviary housing produced the highest whole-egg total solids between 31 to 60 wk of hen age, whereas brown shell eggs resulted in the most consistent level of whole-egg total solids (22-23.5%). The brown and white shell strains in the current study produce cage-free aviary eggs with distinctive physical quality attributes. The outcomes from this study can be utilized by the U.S. egg industry in planning management strategies and market placement of cage-free eggs.

Anterior cervical discectomy with or without fusion with ray titanium cage: a prospective randomized clinical study

DEFF Research Database (Denmark)

Hauerberg, J.; Kosteljanetz, M.; Bøge-Rasmussen, Torben

2008-01-01

STUDY DESIGN: A prospective randomized clinical study. OBJECTIVE: To compare 2 surgical methods in the treatment of cervical radiculopathy caused by hard or soft disc herniation; namely, simple discectomy versus discectomy with an additional interbody fusion with a Ray titanium cage. SUMMARY...... by fusion with a Ray titanium cage (40 patients) or to discectomy alone (46 patients). Clinical and radiologic follow-up was performed 3, 12, and 24 months after surgery. RESULTS: There was no statistically significant difference between the 2 groups concerning self-reported satisfaction or severity of pain...... adjacent disc degeneration or spondylosis were the same in both groups. CONCLUSION: This study showed no statistically significant difference between simple discectomy and discectomy followed by interbody fusion with a titanium cage in the surgical treatment of cervical radiculopathy caused by disc...

Business plan Tilapia cage farming in Tete Zambezi Valley, Mozambique

NARCIS (Netherlands)

Meer, van der Magnus; Brouwer, Herman

2015-01-01

Tete province offers great opportunities for cage farming of tilapia in Lake Cahora Bassa. The climate and water quality are favourable for fish production, and the fast economic developments in the region will facilitate fish sales. In Tete tilapia (pende) is highly valued food. Major markets for

Avaliação do tratamento da discopatia degenerativa cervical pela artrodese via anterior utilizando placas associadas a cages ou cages em peek isoladamente Evaluación del tratamiento de la enfermedad degenerativa del disco cervical por la artrodesis anterior utilizando placas asociadas con jaulas o jaulas en peec, aisladamente Evaluation of cervical degenerative disc disease treatment by anterior arthrodesis using plates associated with cages or cages in peek alone

Directory of Open Access Journals (Sweden)

André Rafael Hübner

2011-01-01

Full Text Available OBJETIVOS: Avaliar comparativamente o tratamento da discopatia degenerativa cervical por discectomia e artrodese cervical via anterior utilizando placas associadas a cages ou cages em PEEK isoladamente. MÉTODOS: Foi realizado um estudo retrospectivo comparativo entre dois grupos de pacientes operados pela técnica de discectomia e artrodese cervical via anterior. Foram selecionados aleatoriamente 70 pacientes, 35 operados com o método de fixação com placas associadas a cages - denominado Grupo I - e 35 com o cage em PEEK isoladamente - Grupo II. Realizou-se anamnese, exame físico, escores de dor (escala visual e analógica da dor e função (critérios de Odom's, SF-36, Indice de incapacidade do pescoço o pré e pós-operatório e exames de imagem. RESULTADOS: Houve predominância de pacientes do sexo feminino em ambos os grupos, com média de idade de 55 anos no Grupo I e 47 no Grupo II. Ambos os grupos apresentaram distribuição semelhante quanto ao número de níveis operados, assim como nas complicações encontradas e escores de dor, cervicalgia e SF36 no pré e pós-operatório. Houve 97.1% de fusão com 94.3% de bons resultados no Grupo I e 100% de fusão, com 97 % de bons resultados no Grupo II. CONCLUSÕES: O estudo comparativo da utilização de placas com cages e cages em PEEK isoladamente apresentou resultados semelhantes e satisfatórios para os grupos estudados, não se constatando superioridade ou inferioridade de um método com relação ao outro.OBJETIVOS: Evaluar comparativamente el tratamiento de la enfermedad degenerativa del disco cervical por discectomía y artrodesis cervical vía anterior, utilizando placas asociadas con el uso de jaulas o estas en PEEK [Poliéster-Éter-Éter-Cetona], aisladamente. MÉTODOS: fue realizado un estudio retrospectivo comparativo de dos grupos de pacientes tratados con la técnica de discectomía y artrodesis cervical vía anterior. Se seleccionaron al azar 70 pacientes, 35 operados

Detection of early behavioral markers of Huntington's disease in R6/2 mice employing an automated social home cage

DEFF Research Database (Denmark)

Rudenko, Olga; Tkach, Vadim; Berezin, Vladimir

2009-01-01

developed behavior screening system, the IntelliCage, allows automated testing of mouse behavior in the home cage employing individual recognition of animals living in social groups. The present study validates the ability of the IntelliCage system to detect behavioral and cognitive dysfunction in R6/2 mice......Huntington's disease (HD) is an autosomal-dominant neurodegenerative disorder, for which no known cure or effective treatment exists. To facilitate the search for new potential treatments of HD, an automated system for analyzing the behavior of transgenic HD mice is urgently needed. A recently...

Switching Vertical to Horizontal Graphene Growth Using Faraday Cage-Assisted PECVD Approach for High-Performance Transparent Heating Device.

Science.gov (United States)

Qi, Yue; Deng, Bing; Guo, Xiao; Chen, Shulin; Gao, Jing; Li, Tianran; Dou, Zhipeng; Ci, Haina; Sun, Jingyu; Chen, Zhaolong; Wang, Ruoyu; Cui, Lingzhi; Chen, Xudong; Chen, Ke; Wang, Huihui; Wang, Sheng; Gao, Peng; Rummeli, Mark H; Peng, Hailin; Zhang, Yanfeng; Liu, Zhongfan

2018-02-01

Plasma-enhanced chemical vapor deposition (PECVD) is an applicable route to achieve low-temperature growth of graphene, typically shaped like vertical nanowalls. However, for transparent electronic applications, the rich exposed edges and high specific surface area of vertical graphene (VG) nanowalls can enhance the carrier scattering and light absorption, resulting in high sheet resistance and low transmittance. Thus, the synthesis of laid-down graphene (LG) is imperative. Here, a Faraday cage is designed to switch graphene growth in PECVD from the vertical to the horizontal direction by weakening ion bombardment and shielding electric field. Consequently, laid-down graphene is synthesized on low-softening-point soda-lime glass (6 cm × 10 cm) at ≈580 °C. This is hardly realized through the conventional PECVD or the thermal chemical vapor deposition methods with the necessity of high growth temperature (1000 °C-1600 °C). Laid-down graphene glass has higher transparency, lower sheet resistance, and much improved macroscopic uniformity when compare to its vertical graphene counterpart and it performs better in transparent heating devices. This will inspire the next-generation applications in low-cost transparent electronics. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Automated recording of home cage activity and temperature of individual rats housed in social groups: The Rodent Big Brother project.

Science.gov (United States)

Redfern, William S; Tse, Karen; Grant, Claire; Keerie, Amy; Simpson, David J; Pedersen, John C; Rimmer, Victoria; Leslie, Lauren; Klein, Stephanie K; Karp, Natasha A; Sillito, Rowland; Chartsias, Agis; Lukins, Tim; Heward, James; Vickers, Catherine; Chapman, Kathryn; Armstrong, J Douglas

2017-01-01

Measuring the activity and temperature of rats is commonly required in biomedical research. Conventional approaches necessitate single housing, which affects their behavior and wellbeing. We have used a subcutaneous radiofrequency identification (RFID) transponder to measure ambulatory activity and temperature of individual rats when group-housed in conventional, rack-mounted home cages. The transponder location and temperature is detected by a matrix of antennae in a baseplate under the cage. An infrared high-definition camera acquires side-view video of the cage and also enables automated detection of vertical activity. Validation studies showed that baseplate-derived ambulatory activity correlated well with manual tracking and with side-view whole-cage video pixel movement. This technology enables individual behavioral and temperature data to be acquired continuously from group-housed rats in their familiar, home cage environment. We demonstrate its ability to reliably detect naturally occurring behavioral effects, extending beyond the capabilities of routine observational tests and conventional monitoring equipment. It has numerous potential applications including safety pharmacology, toxicology, circadian biology, disease models and drug discovery.

State Feedback Decoupling with In-Loop Lead Compensator in Stand-Alone VSIs

DEFF Research Database (Denmark)

Federico, de Bosio; Pastorelli, Michele; de Sousa Ribeiro, Luiz Antonio

2016-01-01

The performance of current and voltage regulators during transients and steady-state is of primary concern for power converters intended for stand-alone applications. Dynamics performance and command tracking capability are enhanced by actively decoupling the controlled states variables. To further...... widen the current loop bandwidth while still preserving a well-damped system a lead compensator structure on the forward loop is proposed. A 3 kHz bandwidth with 0.707 damping factor is achieved for the inner current controller. Accordingly, also the voltage regulator bandwidth can be widen, thus...

Design and standalone characterisation of a capacitively coupled HV-CMOS sensor chip for the CLIC vertex detector

Science.gov (United States)

Kremastiotis, I.; Ballabriga, R.; Campbell, M.; Dannheim, D.; Fiergolski, A.; Hynds, D.; Kulis, S.; Peric, I.

2017-09-01

The concept of capacitive coupling between sensors and readout chips is under study for the vertex detector at the proposed high-energy CLIC electron positron collider. The CLICpix Capacitively Coupled Pixel Detector (C3PD) is an active High-Voltage CMOS sensor, designed to be capacitively coupled to the CLICpix2 readout chip. The chip is implemented in a commercial 180 nm HV-CMOS process and contains a matrix of 128×128 square pixels with 25μm pitch. First prototypes have been produced with a standard resistivity of ~20 Ωcm for the substrate and tested in standalone mode. The results show a rise time of ~20 ns, charge gain of 190 mV/ke- and ~40 e- RMS noise for a power consumption of 4.8μW/pixel. The main design aspects, as well as standalone measurement results, are presented.

Stand-Alone Ethics, Social Responsibility, and Sustainability Course Requirements: A Snapshot from Australia and New Zealand

Science.gov (United States)

Rundle-Thiele, Sharyn R.; Wymer, Walter

2010-01-01

This article analyzes the extent to which Australian and New Zealand marketing educators use dedicated or stand-alone courses to equip students with alternative views of business. A census of marketing programs in degree-granting universities was conducted. Program brochures were obtained via the Internet and were content analyzed. This study…

SoC-Based Output Voltage Control for BESS with a Lithium-Ion Battery in a Stand-Alone DC Microgrid

Directory of Open Access Journals (Sweden)

Seung-Yeong Yu

2016-11-01

Full Text Available This paper proposes a new DC output voltage control for a battery energy storage system (BESS with a lithium-ion battery based on the state of charge (SoC. The proposed control scheme was verified through computer simulations for a typical stand-alone DC microgrid, which consists of a BESS, photovoltaic (PV panel, engine generator (EG, and DC load. A scaled hardware prototype for a stand-alone DC microgrid was set up in the lab, in which the proposed control scheme was loaded in a DSP controller. The experimental results were compared with the simulation results for performance verification. The proposed control scheme provides relatively lower variation of the DC grid voltage than the conventional droop control.

Ferritin cage for encapsulation and delivery of bioactive nutrients: From structure, property to applications.

Science.gov (United States)

Zang, Jiachen; Chen, Hai; Zhao, Guanghua; Wang, Fudi; Ren, Fazheng

2017-11-22

Ferritin is a class of naturally occurring iron storage proteins, which is distributed widely in animal, plant, and bacteria. It usually consists of 24 subunits that form a hollow protein shell with high symmetry. One holoferritin molecule can store up to 4500 iron atom within its inner cavity, and it becomes apoferritin upon removal of iron from the cavity. Recently, scientists have subverted these nature functions and used reversibly self-assembled property of apoferritin cage controlled by pH for the encapsulation and delivery of bioactive nutrients or anticancer drug. In all these cases, the ferritin cages shield their cargo from the influence of external conditions and provide a controlled microenvironment. More importantly, upon encapsulation, ferritin shell greatly improved the water solubility, thermal stability, photostability, and cellular uptake activity of these small bioactive compounds. This review aims to highlight recent advances in applications of ferritin cage as a novel vehicle in the field of food science and nutrition. Future outlooks are highlighted with the aim to suggest a research line to follow for further studies.

Modeling, Design and Simulation of Stand-Alone Photovoltaic Power Systems with Battery Storage

Directory of Open Access Journals (Sweden)

Abd Essalam BADOUD

2013-06-01

Full Text Available Stand alone renewable energy based on photovoltaic systems accompanied with battery storage system are beginning to play an important role over the world to supply power to remote areas. The objective of the study reported in this paper is to elaborate and design a bond graphs model for sizing stand-alone domestic solar photovoltaic electricity systems and simulating the performance of the systems in a tropical climate. The systems modelled consist of an array of PV modules, a lead-acid battery, and a number of direct current appliances. This paper proposes the combination of lead acid battery system with a typical stand alone photovoltaic energy system under variable loads. The main activities of this work purpose to establish library graphical models for each individual component of standalone photovoltaic system. Control strategy has been considered to achieve permanent power supply to the load via photovoltaic/battery based on the power available from the sun. The complete model was simulated under two testing including sunny and cloudy conditions. Simulation of the system using Symbols software was performed and the results of simulation show the superior stable control system and high efficiency. These results have been contrasted with real measured data from a measurement campaign plant carried on electrical engineering laboratory of Grenoble using various interconnection schemes are presented.

Improvements in nuclear fuel assembly cages

Energy Technology Data Exchange (ETDEWEB)

Eaton, C.W.; Seeley, T.A.; Ince, G.; Speakman, W.T.

1986-03-12

The fuel pin/guide tube supporting grids of an assembly cage for a multi pin fuel element or a reflector element for a stringer are mounted in the moderator sleeve by way of mounting assemblies engaged in grooves machined into the interior surface of the sleeve, each mounting assembly including a split ring which is assembled into its groove by being radially contracted, pushed along the sleeve into registry with the groove and allowed to radially expand. The split ring may carry burnable neutron absorber. The region of the sleeve between two adjacent grids may be of smaller internal diameter than the remainder of the sleeve.

C60 as a Faraday cage

Science.gov (United States)

Delaney, P.; Greer, J. C.

2004-01-01

Endohedral fullerenes have been proposed for a number of technological uses, for example, as a nanoscale switch, memory bit and as qubits for quantum computation. For these technology applications, it is important to know the ease with which the endohedral atom can be manipulated using an applied electric field. We find that the Buckminsterfullerene (C60) acts effectively as a small Faraday cage, with only 25% of the field penetrating the interior of the molecule. Thus influencing the atom is difficult, but as a qubit the endohedral atom should be well shielded from environmental electrical noise. We also predict how the field penetration should increase with the fullerene radius.

Shape optimization of 3D curved slots and its application to the squirrel-cage elastic support design

Science.gov (United States)

Wang, Dan; Zhang, Weihong; Wang, Zhenpei; Zhu, Jihong

2010-10-01

The squirrel-cage elastic support is one of the most important components of an aero-engine rotor system. A proper structural design will favor the static and dynamic performances of the system. In view of the deficiency of the current shape optimization techniques, a new mapping approach is proposed to define shape design variables based on the parametric equations of 3D curves and surfaces. It is then applied for the slot shape optimization of a squirrel-cage elastic support. To this end, an automatic design procedure that integrates the Genetic Algorithm (GA) is developed to solve the problem. Two typical examples with different shape constraints are considered. Numerical results provide reasonable optimum designs for the improvement of stiffness and strength of the squirrel-cage elastic support.

Life on the edge: squirrel-cage fringe fields and their effects in the MBE-4 combiner experiment

International Nuclear Information System (INIS)

Fawley, W.M.

1996-02-01

The MBE-4 combiner experiment employs an electrostatic combined-function focusing/bending element, the so-called ''squirrel-cage'' just before the actual merging region. There has been concern that non-linear fields, primarily in the fringe regions at the beginning and end of the cage, may be strong enough to lead to significant emittance degradation. This note present the results of numerical calculations which determined the anharmonic, non-linear components of the 3D fields in the cage and the resultant, orbit-integrated effects upon the MBE-4 beamlets. We find that while the anharmonic effects are small compared to the dipole deflection, the resultant transverse emittance growth is significant when compared to the expected value of the initial emittance of the individual beamlets

Restoration of lumbopelvic sagittal alignment and its maintenance following transforaminal lumbar interbody fusion (TLIF): comparison between straight type versus curvilinear type cage.

Science.gov (United States)

Kim, Jong-Tae; Shin, Myung-Hoon; Lee, Ho-Jin; Choi, Du-Yong

2015-11-01

To evaluate a radiological and clinical difference between the curvilinear type cages compared to the straight type cages for the restoration of lumbopelvic sagittal alignment and its maintenance after transforaminal lumbar interbody fusion (TLIF) procedure. 68 patients who underwent single-level TLIF using either the straight type or curvilinear type cage were retrospectively reviewed. Assessment of the lumbopelvic parameters and the height of disc space was performed before surgery as well as 2 days, 6 and 12 months after surgery. Clinical outcome was assessed using VAS and ODI. The curvilinear type cages were positioned more anteriorly than the straight type. Restoration of the segmental lordosis (SL) in the curvilinear group was significantly greater than the straight group and at 12 months of follow-up, the straight group showed greater decrease in the disc height than the curvilinear group. The straight group failed to show improvement of lumbar lordosis (LL), while the curvilinear group showed significant restoration of LL and could maintain it to the 6 months of follow-up. In both groups, pelvic tilt was significantly decreased and it lasted to 6 months in the straight group; whereas in the curvilinear group, it was maintained to the last follow-up of 12 months. There were no significant differences between the two groups in mean VAS and ODI score over the follow-up period. This study demonstrates that the curvilinear type cage is superior to the straight type cage in improving the SL and maintaining both the restored lumbopelvic parameters and elevated disc height. These results could be attributable to the anterior position of the curvilinear cage which permits easy restoration of segmental lordosis and less sinking of cages.

EFFICACY OF CAGE PLACEMENT WITHOUT PLATE IN PATIENTS WITH CERVICAL MYELOPATHY WITH SINGLE-LEVEL AFFECTION

Directory of Open Access Journals (Sweden)

CARLOS ALBERTO ZUÑIGA-MAZÓN

Full Text Available ABSTRACT Objective: To determine the efficacy of PEEK (Poly-ether-ether-ketone cage without plate for the treatment of single-level cervical spondylosis. Methods: Ten patients with cervical myelopathy data, with a single-level root condition, seen at the outpatient clinic of the Neurosurgery Service, operated in 2016, mean age 53 years, 6 (60% female, 4 (40% obese, 3 (30% smokers. The Cloward technique was used by anterior approach, discectomy, and PEEK cage placement. Results: At six months of surgery, 100% of the patients had increased intervertebral space, with a 100% reduction in osteophytes; only one patient had dysphagia, no patient had lesion of the adjacent segment and 10% had persistent root pathology. Cervical lordosis was observed in 90% of the patients and arthrodesis in 100% of the cases. Conclusions: Anterior approach arthrodesis using PEEK cage without cervical plate is effective as a treatment of cervical myelopathy in a single level.

Development of a microprocessor controller for stand-alone photovoltaic power systems

Science.gov (United States)

Millner, A. R.; Kaufman, D. L.

1984-01-01

A controller for stand-alone photovoltaic systems has been developed using a low power CMOS microprocessor. It performs battery state of charge estimation, array control, load management, instrumentation, automatic testing, and communications functions. Array control options are sequential subarray switching and maximum power control. A calculator keypad and LCD display provides manual control, fault diagnosis and digital multimeter functions. An RS-232 port provides data logging or remote control capability. A prototype 5 kW unit has been built and tested successfully. The controller is expected to be useful in village photovoltaic power systems, large solar water pumping installations, and other battery management applications.

Clinical experience using polyetheretherketone (PEEK) intervertebral structural cage for anterior cervical corpectomy and fusion.

Science.gov (United States)

Kasliwal, Manish K; O'Toole, John E

2014-02-01

Anterior cervical corpectomy and fusion (ACCF) is commonly performed for various pathologies involving the cervical spine. Although polyetheretherketone (PEEK) cages have been widely used following anterior cervical discectomy and fusion (ACDF), clinical literature demonstrating its efficacy following ACCF is sparse. A retrospective review of patients enrolled in a prospective database who underwent single/multi-level ACCF was performed. Fifty-nine patients were identified who underwent corpectomy reconstruction with PEEK cages for symptomatic degenerative, neoplastic, infectious, or traumatic pathologies of the cervical spine. Thirty-five patients having at least 6 months follow-up (FU) were included in the final analysis. The mean age of patients was 51 years (range, 18-81 years) with FU ranging from 6 to 33 months (mean, 6.6 months). None of the patients had dysphagia at last FU. There was no implant failure with fusion occurring in all patients. While 57% of patients (20/35) remained stable with no progression of myelopathy, 43% (15/35) improved one (11 patients) or two (four patients) Nurick grades after surgery. The use of PEEK cages packed with autograft or allograft is safe and effective following anterior cervical corpectomy, demonstrating high fusion rates and good clinical results. This synthetic material obviates the morbidity associated with autograft harvest and possible infectious risks of allograft. The wide array of cage dimensions facilitates ease of use in patients of all sizes and appears safe for use in the typical pathologic conditions encountered in the cervical spine. Copyright © 2013 Elsevier Ltd. All rights reserved.

A Non-Parametric Item Response Theory Evaluation of the CAGE Instrument Among Older Adults.

Science.gov (United States)

Abdin, Edimansyah; Sagayadevan, Vathsala; Vaingankar, Janhavi Ajit; Picco, Louisa; Chong, Siow Ann; Subramaniam, Mythily

2018-02-23

The validity of the CAGE using item response theory (IRT) has not yet been examined in older adult population. This study aims to investigate the psychometric properties of the CAGE using both non-parametric and parametric IRT models, assess whether there is any differential item functioning (DIF) by age, gender and ethnicity and examine the measurement precision at the cut-off scores. We used data from the Well-being of the Singapore Elderly study to conduct Mokken scaling analysis (MSA), dichotomous Rasch and 2-parameter logistic IRT models. The measurement precision at the cut-off scores were evaluated using classification accuracy (CA) and classification consistency (CC). The MSA showed the overall scalability H index was 0.459, indicating a medium performing instrument. All items were found to be homogenous, measuring the same construct and able to discriminate well between respondents with high levels of the construct and the ones with lower levels. The item discrimination ranged from 1.07 to 6.73 while the item difficulty ranged from 0.33 to 2.80. Significant DIF was found for 2-item across ethnic group. More than 90% (CC and CA ranged from 92.5% to 94.3%) of the respondents were consistently and accurately classified by the CAGE cut-off scores of 2 and 3. The current study provides new evidence on the validity of the CAGE from the IRT perspective. This study provides valuable information of each item in the assessment of the overall severity of alcohol problem and the precision of the cut-off scores in older adult population.

Photolysis of caged phosphatidic acid induces flagellar excision in Chlamydomonas.

NARCIS (Netherlands)

Goedhart, J.; Gadella, Th.W.J.

2004-01-01

Phosphatidic (PtdOH) acid formation is recognized as an important step in numerous signaling pathways in both plants and mammals. To study the role of this lipid in signaling pathways, it is of major interest to be able to increase the amount of this lipid directly. Therefore, "caged" PtdOH was

Effects of prenatal ethanol exposure and early experience on home-cage and open-field activity in mice.

Science.gov (United States)

Mothes, H K; Opitz, B; Werner, R; Clausing, P

1996-01-01

-C57BL/6 mice were intubated from gestational day 14-18 twice daily with 1.58 g/kg ethanol, 4.2 g/kg sucrose, or remained untreated. Offspring of ethanol treated or lab chow control groups were raised either by group-housed dams and weaned on postnatal day (PND) 28 or by individually housed dams and weaned on PND 21. Offspring of the sucrose control group were raised by individually housed dams and weaned on PND 21. Groups did not differ in pup weight or litter size. Offspring were assessed for home-cage activity (PND 36-38) and open-field behavior (PND 40-42). Mice prenatally exposed to ethanol showed increased activity in their home cages, whereas open-field behavior was generally not different from that of control groups. Conversely, different preweaning rearing conditions had affected open-field behavior, but not home-cage activity. In conclusion, home-cage behavior was a sensitive paradigm for detecting hyperactivity subsequent to a relatively low dose of prenatal ethanol in mice, and communal nesting/late weaning vs. individual nesting/ standard weaning may be a useful preweaning environmental manipulation to study possible modifications of prenatal neurobehavioral effects.

A Case Study of Control and Improved Simplified Swarm Optimization for Economic Dispatch of a Stand-Alone Modular Microgrid

Directory of Open Access Journals (Sweden)

Xianyong Zhang

2018-03-01

Full Text Available Due to the complex configuration and control framework, the conventional microgrid is not cost-effective for engineering applications with small or medium capacity. A stand-alone modular microgrid with separated AC bus and decentralized control strategy is proposed in this paper. Each module is a self-powered system, which consists of wind and solar power, a storage battery, load and three-port converter. The modules are interconnected by three-port converters to form the microgrid. Characteristics, operation principle, control of the modular microgrid and the three-port converter are analyzed in detail. Distributed storage batteries enable power exchanges among modules to enhance economic returns. Economic dispatch of the stand-alone modular microgrid is a mixed-integer programming problem. A day-ahead operation optimization model including fuel cost, battery operation cost, and power transmission cost is established. Because there are so many constraints, it is difficult to produce a feasible solution and even more difficult to have an improved solution. An improved simplified swarm optimization (iSSO method is therefore proposed. The iSSO scheme designs the new update mechanism and survival of the fittest policy. The experimental results from the demonstration project on DongAo Island reflect the effectiveness of the stand-alone modular microgrid and the economic dispatch strategy based on the iSSO method.

Curating viscoelastic properties of icosahedral viruses, virus-based nanomaterials, and protein cages.

Science.gov (United States)

Kant, Ravi; Rayaprolu, Vamseedhar; McDonald, Kaitlyn; Bothner, Brian

2018-06-01

The beauty, symmetry, and functionality of icosahedral virus capsids has attracted the attention of biologists, physicists, and mathematicians ever since they were first observed. Viruses and protein cages assemble into functional architectures in a range of sizes, shapes, and symmetries. To fulfill their biological roles, these structures must self-assemble, resist stress, and are often dynamic. The increasing use of icosahedral capsids and cages in materials science has driven the need to quantify them in terms of structural properties such as rigidity, stiffness, and viscoelasticity. In this study, we employed Quartz Crystal Microbalance with Dissipation technology (QCM-D) to characterize and compare the mechanical rigidity of different protein cages and viruses. We attempted to unveil the relationships between rigidity, radius, shell thickness, and triangulation number. We show that the rigidity and triangulation numbers are inversely related to each other and the comparison of rigidity and radius also follows the same trend. Our results suggest that subunit orientation, protein-protein interactions, and protein-nucleic acid interactions are important for the resistance to deformation of these complexes, however, the relationships are complex and need to be explored further. The QCM-D based viscoelastic measurements presented here help us elucidate these relationships and show the future prospect of this technique in the field of physical virology and nano-biotechnology.

Modified Chaos Particle Swarm Optimization-Based Optimized Operation Model for Stand-Alone CCHP Microgrid

Directory of Open Access Journals (Sweden)

Fei Wang

2017-07-01

Full Text Available The optimized dispatch of different distributed generations (DGs in stand-alone microgrid (MG is of great significance to the operation’s reliability and economy, especially for energy crisis and environmental pollution. Based on controllable load (CL and combined cooling-heating-power (CCHP model of micro-gas turbine (MT, a multi-objective optimization model with relevant constraints to optimize the generation cost, load cut compensation and environmental benefit is proposed in this paper. The MG studied in this paper consists of photovoltaic (PV, wind turbine (WT, fuel cell (FC, diesel engine (DE, MT and energy storage (ES. Four typical scenarios were designed according to different day types (work day or weekend and weather conditions (sunny or rainy in view of the uncertainty of renewable energy in variable situations and load fluctuation. A modified dispatch strategy for CCHP is presented to further improve the operation economy without reducing the consumers’ comfort feeling. Chaotic optimization and elite retention strategy are introduced into basic particle swarm optimization (PSO to propose modified chaos particle swarm optimization (MCPSO whose search capability and convergence speed are improved greatly. Simulation results validate the correctness of the proposed model and the effectiveness of MCPSO algorithm in the optimized operation application of stand-alone MG.

Design of a Stand-Alone Photovoltaic (PV Models for Home Lightings and Clean Environment

Directory of Open Access Journals (Sweden)

Vincent Anayochukwu Ani

2016-01-01

Full Text Available This paper gives a well-documented health risks of fuel-based lighting (kerosene lamps and fuel-powered generators and proposed a design of a stand-alone solar PV system for sustainable home lightings in rural Nigerian area. The design was done in three different patterns of electricity consumptions with energy efficient lightings (EELs using two different battery types (Rolls Surrette 6CS25PS and hoppecke 10 OpzS 1000 on; i judicious power consumption, ii normal power consumption, iii excess power consumption; and compared them with the incandescent light bulb consumption. The stand-alone photovoltaic energy systems were designed to match the rural Nigerian sunlight and weather conditions to meet the required lightings of the household. The objective function and constraints for the design models were formulated and optimization procedure were used to demonstrate the best solution (reliability at the lowest lifecycle cost. Initial capital costs as well as annualized costs over 5, 10, 15, 20, and 25 years were quantified and documented. The design identified the most cost-effective and reliable solar and battery array among the patterns of electricity consumption with energy efficient lighting options (judicious power consumption, normal power consumption, and excess power consumption.

Numerical simulation of blast wave propagation in vicinity of standalone prism on flat plate

Science.gov (United States)

Valger, Svetlana; Fedorova, Natalya; Fedorov, Alexander

2018-03-01

In the paper, numerical simulation of shock wave propagation in the vicinity of a standalone prism and a prism with a cavity in front of it was carried out. The modeling was based on the solution of 3D Euler equations and Fluent software was used as a main computational tool. The algorithm for local dynamic mesh adaptation to high gradients of pressure was applied. The initial stage of the explosion of condensed explosive was described with the help of "Compressed balloon method". The research allowed describing the characteristic stages of the blast in a semi-closed space, the structure of secondary shock waves and their interaction with obstacles. The numerical approach in Fluent based on combining inviscid gas dynamics methods and "Compressed balloon method" was compared with the method which had been used by the authors earlier with the help of AUTODYN and which is based on the use of the hydrodynamic model of a material to describe state of detonation products. For the problem of shock wave propagation in the vicinity of standalone prism the comparison of the simulation results obtained using both the methods with the experimental data was performed on the dependence of static pressure and effective momentum on time for the characteristic points located on prism walls.

Standalone computer-aided detection compared to radiologists' performance for the detection of mammographic masses

International Nuclear Information System (INIS)

Hupse, Rianne; Samulski, Maurice; Imhof-Tas, Mechli W.; Karssemeijer, Nico; Lobbes, Marc; Boetes, Carla; Heeten, Ard den; Beijerinck, David; Pijnappel, Ruud

2013-01-01

We developed a computer-aided detection (CAD) system aimed at decision support for detection of malignant masses and architectural distortions in mammograms. The effect of this system on radiologists' performance depends strongly on its standalone performance. The purpose of this study was to compare the standalone performance of this CAD system to that of radiologists. In a retrospective study, nine certified screening radiologists and three residents read 200 digital screening mammograms without the use of CAD. Performances of the individual readers and of CAD were computed as the true-positive fraction (TPF) at a false-positive fraction of 0.05 and 0.2. Differences were analysed using an independent one-sample t-test. At a false-positive fraction of 0.05, the performance of CAD (TPF = 0.487) was similar to that of the certified screening radiologists (TPF = 0.518, P = 0.17). At a false-positive fraction of 0.2, CAD performance (TPF = 0.620) was significantly lower than the radiologist performance (TPF = 0.736, P <0.001). Compared to the residents, CAD performance was similar for all false-positive fractions. The sensitivity of CAD at a high specificity was comparable to that of human readers. These results show potential for CAD to be used as an independent reader in breast cancer screening. (orig.)

The encapsulation of trimetallic nitride clusters in fullerene cages

International Nuclear Information System (INIS)

Dorn, H.C.; Stevenson, S.; Craft, J.; Cromer, F.; Duchamp, J.; Rice, G.; Glass, T.; Harich, K.; Fowler, P.W.; Heine, T.; Hajdu, E.; Bible, R.; Olmstead, M.M.; Maitra, K.; Fisher, A.J.; Balch, A.L.

2000-01-01

The Kratschmer-Huffman electric-arc generator typically produces endohedral metallofullerenes in low yields with a wide array of different products, but the introduction of nitrogen leads to a new family of encapsulates. A family of endohedral metallofullerenes A n B 3-n N at C 2n (n=0-3, x=34, 39, and 40) where A and B are Group III and rare-earth metals is formed by a trimetallic nitride template (TNT) process in relatively high yields. The archetypal representative of this new class is the stable endohedral metallofullerene, Sc 3 N at C 80 containing a triscandium nitride cluster encapsulated in an icosahedron (I h ), C 80 cage. The Sc 3 N at C 80 is formed in yields even exceeding empty-cage C 84 . Other prominent scandium TNT members are Sc 3 N at C 68 and Sc 3 N at C 78 . The former Sc 3 N at C 68 molecule represents an exception to the well known isolated pentagon rule (IPR). These new molecules were purified by chromatography with corresponding characterization by various spectroscopic approaches. In this paper we focus on the characterization and properties of this fascinating new class of materials

(reprocessed)HeliscopeCAGE sequencing, Delve mapping and CAGE TSS aggregation - FANTOM5 | LSDB Archive [Life Science Database Archive metadata

Lifescience Database Archive (English)

Full Text Available switchLanguage; BLAST Search Image Search Home About Archive Update History Data List Contact us FANTOM...ntified by CAGE tag analysis (BED format) *.rdna.fa.gz: rDNA sequences (FASTA format) Data file File name: fantom...5_rp_exp_details.zip File URL: ftp://ftp.biosciencedbc.jp/archive/fantom5/20161221/fantom5_rp_exp_detai...tp://ftp.biosciencedbc.jp/archive/fantom5/datafiles/reprocessed/hg38_latest/basic/ File size: 1.4 TB File na...me: (reprocessed)basic (Mus musculus) File URL: ftp://ftp.biosciencedbc.jp/archive/fantom5/datafiles/reproce

Hierarchical energy management system for stand-alone hybrid system based on generation costs and cascade control

International Nuclear Information System (INIS)

Torreglosa, J.P.; García, P.; Fernández, L.M.; Jurado, F.

2014-01-01

Highlights: • We present an energy management system for a stand-alone WT/PV/hydrogen/battery hybrid system. • Hierarchical control composed by master and slave control strategies. • Control assures reliable electricity support for stand-alone applications subject to technical and economic criteria. - Abstract: This paper presents an energy management system (EMS) for stand-alone hybrid systems composed by photovoltaic (PV) solar panels and a wind turbine (WT) as primary energy sources and two energy storage systems, which are a hydrogen system and a battery. The hydrogen system is composed of fuel cell (FC), electrolyzer and hydrogen storage tank. The EMS is a hierarchical control composed by a master control strategy and a slave control strategy. On the one hand, the master control generates the reference powers to meet several premises (such as to satisfy the load power demand, and to maintain the hydrogen tank level and the state of charge (SOC) of the battery between their target margins), taking also into account economic aspects to discriminate between using the battery or hydrogen system. On the other hand, the slave control modifies the reference powers generated by the master control according to the energy sources dynamic limitations, and maintains the DC bus voltage at its reference value. The models, implemented in MATLAB-Simulink environment, have been developed from commercially available components. To check the viability of the proposed EMS, two kinds of simulations were carried out: (1) A long-term simulation of 25 years (expected lifetime of the system) with a sample time of one hour to validate the master control of the EMS; and (2) A short-term simulation with sudden net power variations to validate the slave control of the EMS

Assessment of the Usability of the Workbench Faraday Cage Method

OpenAIRE

Sørensen, Morten; Franek, Ondrej; Christensen, Søren K.; Pedersen, Gert Frølund; Ebert, Hans

2011-01-01

The workbench Faraday Cage method (WBFC) is a time efficient module pre-compliance test regarding radiated emission. This work investigates the method’s usability and credibility and concludes that for this particular case the WBFC perform a tolerable compliance test for frequencies below 360 MHz while it is essentially useless for higher frequencies.

Proposed Framework for the Evaluation of Standalone Corpora Processing Systems: An Application to Arabic Corpora

Directory of Open Access Journals (Sweden)

Abdulmohsen Al-Thubaity

2014-01-01

Full Text Available Despite the accessibility of numerous online corpora, students and researchers engaged in the fields of Natural Language Processing (NLP, corpus linguistics, and language learning and teaching may encounter situations in which they need to develop their own corpora. Several commercial and free standalone corpora processing systems are available to process such corpora. In this study, we first propose a framework for the evaluation of standalone corpora processing systems and then use it to evaluate seven freely available systems. The proposed framework considers the usability, functionality, and performance of the evaluated systems while taking into consideration their suitability for Arabic corpora. While the results show that most of the evaluated systems exhibited comparable usability scores, the scores for functionality and performance were substantially different with respect to support for the Arabic language and N-grams profile generation. The results of our evaluation will help potential users of the evaluated systems to choose the system that best meets their needs. More importantly, the results will help the developers of the evaluated systems to enhance their systems and developers of new corpora processing systems by providing them with a reference framework.

Proposed framework for the evaluation of standalone corpora processing systems: an application to Arabic corpora.

Science.gov (United States)

Al-Thubaity, Abdulmohsen; Al-Khalifa, Hend; Alqifari, Reem; Almazrua, Manal

2014-01-01

Despite the accessibility of numerous online corpora, students and researchers engaged in the fields of Natural Language Processing (NLP), corpus linguistics, and language learning and teaching may encounter situations in which they need to develop their own corpora. Several commercial and free standalone corpora processing systems are available to process such corpora. In this study, we first propose a framework for the evaluation of standalone corpora processing systems and then use it to evaluate seven freely available systems. The proposed framework considers the usability, functionality, and performance of the evaluated systems while taking into consideration their suitability for Arabic corpora. While the results show that most of the evaluated systems exhibited comparable usability scores, the scores for functionality and performance were substantially different with respect to support for the Arabic language and N-grams profile generation. The results of our evaluation will help potential users of the evaluated systems to choose the system that best meets their needs. More importantly, the results will help the developers of the evaluated systems to enhance their systems and developers of new corpora processing systems by providing them with a reference framework.

Weighted density approximation for bonding in molecules: ring and cage polymers

CERN Document Server

Sweatman, M B

2003-01-01

The focus of this work is the bonded contribution to the intrinsic Helmholtz free energy of molecules. A weighted density approximation (WDA) for this contribution is presented within the interaction site model (ISM) for ring and cage polymers. The resulting density functional theory (ISM/WDA) for these systems is no more complex than theories for a pure simple fluid, and much less complex than density functional approaches that treat the bonding functional exactly. The ISM/WDA bonding functional is much more accurate than either the ISM/HNC or ISM/PY bonding functionals, which are related to the reference interaction-site model (RISM)/HNC and RISM/PY integral equations respectively, for ideal ring polymers. This means that the ISM/WDA functional should generally be more accurate for most 'real' ring or cage polymer systems when any reasonable approximation for the 'excess' contribution to the intrinsic Helmholtz free energy is employed.

Weighted density approximation for bonding in molecules: ring and cage polymers

International Nuclear Information System (INIS)

Sweatman, M B

2003-01-01

The focus of this work is the bonded contribution to the intrinsic Helmholtz free energy of molecules. A weighted density approximation (WDA) for this contribution is presented within the interaction site model (ISM) for ring and cage polymers. The resulting density functional theory (ISM/WDA) for these systems is no more complex than theories for a pure simple fluid, and much less complex than density functional approaches that treat the bonding functional exactly. The ISM/WDA bonding functional is much more accurate than either the ISM/HNC or ISM/PY bonding functionals, which are related to the reference interaction-site model (RISM)/HNC and RISM/PY integral equations respectively, for ideal ring polymers. This means that the ISM/WDA functional should generally be more accurate for most 'real' ring or cage polymer systems when any reasonable approximation for the 'excess' contribution to the intrinsic Helmholtz free energy is employed

Binding of chemical warfare agent simulants as guests in a coordination cage: contributions to binding and a fluorescence-based response.

Science.gov (United States)

Taylor, Christopher G P; Piper, Jerico R; Ward, Michael D

2016-05-07

Cubic coordination cages act as competent hosts for several alkyl phosphonates used as chemical warfare agent simulants; a range of cage/guest structures have been determined, contributions to guest binding analysed, and a fluorescent response to guest binding demonstrated.

Control System for Producing Electricity with Dual Stator Winding Cage-Rotor Induction Generator

Directory of Open Access Journals (Sweden)

Lucian Nicolae Tutelea

2014-09-01

Full Text Available This paper will present the key design equations and control design model of the Dual Stator Winding Cage-Rotor Induction Generator (DSWIG to achieve wide-speed-range operation with reduced capacity of the static power controller for low power wind or hydro applications. The proposed induction generator consists of a standard squirrel-cage rotor and a stator with two separate windings wound for a similar number of poles. Moreover, the system control strategy using the stator flux orientation is consequently proposed. The aim of the paper is to emphasize that the low speed induction generators with power electronic converters represent a realistic and useful solution for direct drive power applications.

Improved double integral sliding mode MPPT controller based parameter estimation for a stand-alone photovoltaic system

International Nuclear Information System (INIS)

Chatrenour, Nasrin; Razmi, Hadi; Doagou-Mojarrad, Hasan

2017-01-01

Highlights: • IDISMC based MPPT algorithm is introduced. • Hurwitz stability theorem is used for switching surface coefficients computation. • GA approach is presented for parameter estimation of the stand-alone PV system. - Abstract: In this paper, an Improved Double Integral Sliding Mode MPPT Controller (IDISMC) for a stand-alone photovoltaic (PV) system is proposed. Performance of a sliding mode controller (SMC) is greatly influenced by the choice of the sliding surface. Switching surface coefficients were selected by the use of Hurwitz stability theorem. The IDISMC not only is robust against parametric and non-parametric uncertainties, but also has a very small steady-state error, thanks to the use of double integral of tracking voltage error in the definition of its sliding surface. For realistic simulation, Genetic Algorithm (GA) method was used to estimate parameters of solar panels model. The validity of the proposed double integral SMC in maximum power point tracking was approved by comparing the simulation results obtained for a sample PV system with the results of other methods.

Response of phytoplankton to an experimental fish culture in net cages in a subtropical reservoir.

Science.gov (United States)

Bartozek, E C R; Bueno, N C; Feiden, A; Rodrigues, L C

2016-01-01

This study aimed to evaluate nutrients concentration and spatial-temporal changes in phytoplankton biovolume during an experimental fish culture in net cages in a lateral arm of Salto Caxias reservoir, Brazil. Two sampling stations were placed in the affected lateral arm and other two in a cageless lateral arm. Neither abiotic variables nor phytoplankton biovolume presented significant differences between the treatments. Only temporal changes were confirmed by the analysis performed. Both lateral arms were classified as oligotrophic, reflecting low influence of the net cages. Phytoplankton growth seems to be limited by nitrogen. Biovolume values were, in general, low and five major functional groups were recognized (E, F, G, K and P). In summer higher biovolume values were observed and representatives of Chlorophyceae and Cyanobacteria belonging to the functional groups F and K, respectively, were the most important. In winter phytoplankton was mainly composed by Bacillariophyceae taxa from P group. G group was also restricted to winter and E group occurred in winter and summer. The variations recorded in phytoplankton structure appear to have been mainly influenced by seasonal changes in temperature, precipitation and nutrients availability. The effects of net cages on the abiotic variables and phytoplankton biovolume appear to have been small, probably due to the small number of net cages employed and the system dilution capacity. However, a permanent monitoring of phytoplankton is recommended, since this environment has a carrying capacity, from which the trophic state may increase.

Lordosis restoration after anterior longitudinal ligament release and placement of lateral hyperlordotic interbody cages during the minimally invasive lateral transpsoas approach: a radiographic study in cadavers.

Science.gov (United States)

Uribe, Juan S; Smith, Donald A; Dakwar, Elias; Baaj, Ali A; Mundis, Gregory M; Turner, Alexander W L; Cornwall, G Bryan; Akbarnia, Behrooz A

2012-11-01

In the surgical treatment of spinal deformities, the importance of restoring lumbar lordosis is well recognized. Smith-Petersen osteotomies (SPOs) yield approximately 10° of lordosis per level, whereas pedicle subtraction osteotomies result in as much as 30° increased lumbar lordosis. Recently, selective release of the anterior longitudinal ligament (ALL) and placement of lordotic interbody grafts using the minimally invasive lateral retroperitoneal transpsoas approach (XLIF) has been performed as an attempt to increase lumbar lordosis while avoiding the morbidity of osteotomy. The objective of the present study was to measure the effect of the selective release of the ALL and varying degrees of lordotic implants placed using the XLIF approach on segmental lumbar lordosis in cadaveric specimens between L-1 and L-5. Nine adult fresh-frozen cadaveric specimens were placed in the lateral decubitus position. Lateral radiographs were obtained at baseline and after 4 interventions at each level as follows: 1) placement of a standard 10° lordotic cage, 2) ALL release and placement of a 10° lordotic cage, 3) ALL release and placement of a 20° lordotic cage, and 4) ALL release and placement of a 30° lordotic cage. All four cages were implanted sequentially at each interbody level between L-1 and L-5. Before and after each intervention, segmental lumbar lordosis was measured in all specimens at each interbody level between L-1 and L-5 using the Cobb method on lateral radiography. The mean baseline segmental lordotic angles at L1-2, L2-3, L3-4, and L4-5 were -3.8°, 3.8°, 7.8°, and 22.6°, respectively. The mean lumbar lordosis was 29.4°. Compared with baseline, the mean postimplantation increase in segmental lordosis in all levels combined was 0.9° in Intervention 1 (10° cage without ALL release); 4.1° in Intervention 2 (ALL release with 10° cage); 9.5° in Intervention 3 (ALL release with 20° cage); and 11.6° in Intervention 4 (ALL release with 30° cage

Infections of nervous necrosis virus in wild and cage-reared marine fish from South China Sea with unexpected wide host ranges.

Science.gov (United States)

Liu, X D; Huang, J N; Weng, S P; Hu, X Q; Chen, W J; Qin, Z D; Dong, X X; Liu, X L; Zhou, Y; Asim, M; Wang, W M; He, J G; Lin, L

2015-06-01

The concerns about the impact of the nervous necrosis virus (NNV) infections in wild fish have been raised. This paper presents the results of quarterly surveys of NNV in wild and cage-reared marine fish from South China Sea. Samples of 892 wild fish belonging to 69 species and 381 cage-reared fish belonging to 11 species were collected and were detected by seminested PCR and nested PCR. In the case of seminested PCR, the positive signal was detected in 3.0% and 3.1% samples of wild and cage-reared fish, respectively. However, by nested RT-PCR, the positive signal was observed in 42.3% and 63.0% samples of wild and cage-reared fish, respectively. If the fish species were considered, the positive signal was detected in 21.7% and 72.7% species of wild and cage-reared fish by seminested PCR assay, respectively. However, by nested RT-PCR, the positive signal was observed in 65.2% and 100% species of wild and cage-reared fish, respectively. The nucleotide sequences of the nested PCR products were determined. Phylogenetic tree showed that all the obtained viral isolates belonged to the red-spotted grouper nervous necrosis virus (RGNNV) genotype. Thirty-five species of the marine fish were the new hosts of NNV. © 2014 John Wiley & Sons Ltd.

Cross-Cultural Adaptation and Psychometric Properties of the AUDIT and CAGE Questionnaires in Tanzanian Swahili for a Traumatic Brain Injury Population.

Science.gov (United States)

Vissoci, Joao Ricardo Nickenig; Hertz, Julian; El-Gabri, Deena; Andrade Do Nascimento, José Roberto; Pestillo De Oliveira, Leonardo; Mmbaga, Blandina Theophil; Mvungi, Mark; Staton, Catherine A

2018-01-01

To develop Swahili versions of the Alcohol Use Disorders Identification Test (AUDIT) and CAGE questionnaires and evaluate their psychometric properties in a traumatic brain injury (TBI) population in Tanzania. Swahili versions of the AUDIT and CAGE were developed through translation and back-translation by a panel of native speakers of both English and Swahili. The translated instruments were administered to a sample of Tanzanian adults from a TBI registry. The validity and reliability were analyzed using standard statistical methods. The translated versions of both the AUDIT and CAGE questionnaires were found to have excellent language clarity and domain coherence. Reliability was acceptable (>0.85) for all tested versions. Confirmatory factor analysis of one, two and three factor solution for the AUDIT and one factor solution for the CAGE showed adequate results. AUDIT and CAGE scores were strongly correlated to each other (R > 0.80), and AUDIT scores were significantly lower in non-drinkers compared to drinkers. This article presents the first Swahili and Tanzanian adaptations of the AUDIT and CAGE instruments as well as the first validation of these questionnaires with TBI patients. Both instruments were found to have acceptable psychometric properties, resulting in two new useful tools for medical and social research in this setting. © The Author 2017. Medical Council on Alcohol and Oxford University Press. All rights reserved.

Rotor cage fault diagnosis in three-phase induction motors based on a current and virtual flux approach

International Nuclear Information System (INIS)

Pires, Dulce F.; Pires, V. Fernao; Martins, J.F.; Pires, A.J.

2009-01-01

This paper focuses on the detection of a rotor cage fault in a three-phase PWM feed induction motor. In inverter-fed machines there are some difficulties for the detection of a rotor cage fault. These difficulties are due to the fault signature that will be contained in the currents or voltages applied to the machine. In this way, a new approach based on the current and a virtual flux is proposed. The use of the virtual flux allows the improving of the signal to noise ratio. This approach also allows the identification of a rotor cage fault independently of the type of control used in the ac drive. The theoretical principle of this method is discussed. Simulation and experimental results are presented in order to show the effectiveness of the proposed approach

Caged Garcinia Xanthones, a Novel Chemical Scaffold with Potent Antimalarial Activity.

Science.gov (United States)

Ke, Hangjun; Morrisey, Joanne M; Qu, Shiwei; Chantarasriwong, Oraphin; Mather, Michael W; Theodorakis, Emmanuel A; Vaidya, Akhil B

2017-01-01

Caged Garcinia xanthones (CGXs) constitute a family of natural products that are produced by tropical/subtropical trees of the genus Garcinia CGXs have a unique chemical architecture, defined by the presence of a caged scaffold at the C ring of a xanthone moiety, and exhibit a broad range of biological activities. Here we show that synthetic CGXs exhibit antimalarial activity against Plasmodium falciparum, the causative parasite of human malaria, at the intraerythrocytic stages. Their activity can be substantially improved by attaching a triphenylphosphonium group at the A ring of the caged xanthone. Specifically, CR135 and CR142 were found to be highly effective antimalarial inhibitors, with 50% effective concentrations as low as ∼10 nM. CGXs affect malaria parasites at multiple intraerythrocytic stages, with mature stages (trophozoites and schizonts) being more vulnerable than immature rings. Within hours of CGX treatment, malaria parasites display distinct morphological changes, significant reduction of parasitemia (the percentage of infected red blood cells), and aberrant mitochondrial fragmentation. CGXs do not, however, target the mitochondrial electron transport chain, the target of the drug atovaquone and several preclinical candidates. CGXs are cytotoxic to human HEK293 cells at the low micromolar level, which results in a therapeutic window of around 150-fold for the lead compounds. In summary, we show that CGXs are potent antimalarial compounds with structures distinct from those of previously reported antimalarial inhibitors. Our results highlight the potential to further develop Garcinia natural product derivatives as novel antimalarial agents. Copyright © 2016 American Society for Microbiology.

Spray washing, absorbent corn starch powder and dry time to reduce bacterial numbers on soiled boiler transport cage flooring

Science.gov (United States)

Most broilers in the U.S. are transported live to slaughter facilities in cages with fiberglass floors. Cages are often used repeatedly without washing and fecal matter deposited on the floor surface can transfer Campylobacter from one flock to another. Drying feces out between uses is an effectiv...

Environmental enrichment reduces signs of boredom in caged mink.

Directory of Open Access Journals (Sweden)

Rebecca K Meagher

Full Text Available Animals housed in impoverished cages are often labelled 'bored'. They have also been called 'apathetic' or 'depressed', particularly when profoundly inactive. However, these terms are rarely operationally defined and validated. As a negative state caused by under-stimulation, boredom should increase interest in stimuli of all kinds. Apathy (lack of interest, by contrast, should manifest as decreased interest in all stimuli, while anhedonia (loss of pleasure, a depressive symptom should specifically decrease interest in normally rewarding stimuli. We tested the hypotheses that mink, a model carnivore, experience more boredom, depression-like apathy, or anhedonia in non-enriched (NE cages than in complex, enriched (E cages. We exposed 29 subjects (13 E, 16 NE to ten stimuli categorized a priori as aversive (e.g. air puffs, rewarding (e.g. evoking chasing or ambiguous/neutral (e.g. candles. Interest in stimuli was assessed via latencies to contact, contact durations, and durations oriented to stimuli. NE mink contacted all stimuli faster (P = 0.003 than E mink, and spent longer oriented to/in contact with them, albeit only significantly so for ambiguous ones (treatment*type P<0.013. With stimulus category removed from statistical models, interest in all stimuli was consistently higher among NE mink (P<0.0001 for all measures. NE mink also consumed more food rewards (P = 0.037. Finally, we investigated whether lying down while awake and stereotypic behaviour (both increased by NE housing predicted these responses. Lying awake positively co-varied with certain measures of increased exploration. In contrast, stereotypic 'scrabbling' or locomotion (e.g. pacing did not. Overall, NE mink showed no evidence of apathy or depression, but instead a heightened investigation of diverse stimuli consistent with boredom. This state was potentially indicated by spending much time lying still but awake (although this result requires replication. Boredom can

Chemistry of nuclear recoil 18F atoms. VIII. Mechanisms and yields of caging reactions in liquid phase 1,1-difluoroethane and 1,1,1-trifluoroethane

International Nuclear Information System (INIS)

Manning, R.G.; Root, J.W.

1976-01-01

New procedures are reported for the specification of caging yields in nuclear recoil chemistry experiments. All five hot 18 F substitution channels in CH 3 CF 3 and CH 3 CHF 2 exhibit caging at large density. The respective total caged yields at 195 degreeK are 4.0% +- 0.6% and 5.6% +- 0.6%, and the total yields of stabilized substitution products are 8.9% +- 0.4% and 8.6% +- 0.6%. The simplest plausible caging mechanism involves primary Franck--Rabinowitsch radical recombination of 18 F atoms with aliphatic radicals. Density-variation results cannot be used for the qualitative detection of caging reactions unless excitation-stabilization complications have been shown to be unimportant

A Simple Sizing Algorithm for Stand-Alone PV/Wind/Battery Hybrid Microgrids

Directory of Open Access Journals (Sweden)

Jing Li

2012-12-01

Full Text Available In this paper, we develop a simple algorithm to determine the required number of generating units of wind-turbine generator and photovoltaic array, and the associated storage capacity for stand-alone hybrid microgrid. The algorithm is based on the observation that the state of charge of battery should be periodically invariant. The optimal sizing of hybrid microgrid is given in the sense that the life cycle cost of system is minimized while the given load power demand can be satisfied without load rejection. We also report a case study to show the efficacy of the developed algorithm.

Urea and Guanidinium Induced Denaturation of a Trp-Cage Miniprotein

Czech Academy of Sciences Publication Activity Database

Heyda, Jan; Kožíšek, Milan; Bednárová, Lucie; Thompson, G.; Konvalinka, Jan; Vondrášek, Jiří; Jungwirth, Pavel

2011-01-01

Roč. 115, č. 28 (2011), s. 8910-8924 ISSN 1520-6106 R&D Projects: GA MŠk LC512; GA ČR GA203/08/0114 Institutional research plan: CEZ:AV0Z40550506 Keywords : trp-cage denaturation * urea * guanidinium * molecular dynamics Subject RIV: CC - Organic Chemistry Impact factor: 3.696, year: 2011

Sulfiphilic nickel phosphosulfide enabled Li_2S impregnation in 3D graphene cages for Li-S batteries

International Nuclear Information System (INIS)

Zhou, Guangmin; Sun, Jie; Jin, Yang; Chen, Wei; Zu, Chenxi

2017-01-01

A 3D graphene cage with a thin layer of electrodeposited nickel phosphosulfide for Li_2S impregnation, using ternary nickel phosphosulphide as a highly conductive coating layer for stabilized polysulfide chemistry, is accomplished by the combination of theoretical and experimental studies. As a result, the 3D interconnected graphene cage structure leads to high capacity, good rate capability and excellent cycling stability in a Li_2S cathode.

INTERACTIVE EFFECT OF CAGE DENSITY AND DIETARY BLACK CUMIN LEVEL ON PRODUCTIVE EFFICIENCY IN BROILER CHICKENS

Directory of Open Access Journals (Sweden)

L. D. Mahfudz

2015-09-01

Full Text Available The present research was aimed to evaluate an interactive effect of cage density and level ofdietary black cumin (BC on productive efficiency of broiler chickens. A total of 270 broiler chickens(initial body weight of 163.12 ± 8.10g were allocated into a completely randomized design with a 3 x 3factorial pattern. The first factor was the cage density (bird/m2 namely, D1 = 8; D2 = 10, and D3 = 12.The second factor was BC level (%, namely, B1 = 1; B2 = 2, and B3 = 3. Feed consumption, bodyweight gain (BWG, feed conversion ratio (FCR, protein digestibility, and income over feed cost(IOFC were the parameters measured. Data were subjected to ANOVA and continued to Duncan test.No interaction between cage density and black cumin on all parameters was observed. Feedconsumption and FCR were increased, but BWG was lowered significantly (P<0.05 due to the cagedensities of 10 and 12 birds/m2 on weeks 2 and 3. Protein digestibility was significantly increased byfeeding 2 and 3% BC. IOFC decreased significantly (P<0.05 when cage densities were 10 and 12birds/m2. In conclusion, the improvement of productive efficiency of broiler chicken reared at the cagedensity of 12 birds /m2 can be sufficiently achieved by feeding 1% black cumin.

Exogenous control over intracellular acidification: Enhancement via proton caged compounds coupled to gold nanoparticles and an alternative pathway with DMSO

Directory of Open Access Journals (Sweden)

Marilena Carbone

2016-03-01

Full Text Available Proton caged compounds exhibit a characteristic behavior when directly dosed into cells or being coupled to gold nanoparticles prior to the dosing. When irradiated in the near ultraviolet region, they release protons that interact with intracellular HCO3− to yield H2CO3. The dissociation of carbonic acid, then, releases CO2 that can be distinctively singled out in infrared spectra.In the process of searching a pathway to augment the intracellular uptake of proton caged compounds, we probed the association of 1-(2-nitrophenyl-ethylhexadecyl sulfonate (HDNS with DMSO, an agent to enhance the membrane permeability. We found out a different UV-induced protonation mechanism that opens up to new conduits of employing of proton caged compounds. Here, we report the infrared data we collected in this set of experiments. Keywords: Proton caged compounds, DMSO, Intracellular proton release

A control strategy for PV stand-alone applications

International Nuclear Information System (INIS)

Slouma, S; Baccar, H

2015-01-01

This paper proposes a stand-alone photovoltaic (PV) system study in domestic applications. Because of the decrease in power of photovoltaic module as a consequence of changes in solar radiation and temperature which affect the photovoltaic module performance, the design and control of DC-DC buck converter was proposed for providing power to the load from a photovoltaic source.In fact, the control of this converter is carried out with integrated MPPT (Maximum Power Point Tracking) algorithm which ensures a maximum energy generated by the PV arrays. Moreover, the output stage is composed by a battery energy storage system, dc-ac inverter, LCL filter which enables higher efficiency, low distortion ac waveforms and low leakage currents. The control strategy adopted is cascade control composed by two regulation loops.Simulations performed with PSIM software were able to validate the control system.The realization and testing of the photovoltaic system were achieved in the Photovoltaic laboratory of the Centre for Research and Energy Technologies at the Technopark Borj Cedria. Experimental results verify the effeciency of the proposed system

A control strategy for PV stand-alone applications

Science.gov (United States)

Slouma, S.; Baccar, H.

2015-04-01

This paper proposes a stand-alone photovoltaic (PV) system study in domestic applications. Because of the decrease in power of photovoltaic module as a consequence of changes in solar radiation and temperature which affect the photovoltaic module performance, the design and control of DC-DC buck converter was proposed for providing power to the load from a photovoltaic source.In fact, the control of this converter is carried out with integrated MPPT (Maximum Power Point Tracking) algorithm which ensures a maximum energy generated by the PV arrays. Moreover, the output stage is composed by a battery energy storage system, dc-ac inverter, LCL filter which enables higher efficiency, low distortion ac waveforms and low leakage currents. The control strategy adopted is cascade control composed by two regulation loops.Simulations performed with PSIM software were able to validate the control system.The realization and testing of the photovoltaic system were achieved in the Photovoltaic laboratory of the Centre for Research and Energy Technologies at the Technopark Borj Cedria. Experimental results verify the effeciency of the proposed system.

Coding considerations for standalone molecular dynamics simulations of atomistic structures

Science.gov (United States)

Ocaya, R. O.; Terblans, J. J.

2017-10-01

The laws of Newtonian mechanics allow ab-initio molecular dynamics to model and simulate particle trajectories in material science by defining a differentiable potential function. This paper discusses some considerations for the coding of ab-initio programs for simulation on a standalone computer and illustrates the approach by C language codes in the context of embedded metallic atoms in the face-centred cubic structure. The algorithms use velocity-time integration to determine particle parameter evolution for up to several thousands of particles in a thermodynamical ensemble. Such functions are reusable and can be placed in a redistributable header library file. While there are both commercial and free packages available, their heuristic nature prevents dissection. In addition, developing own codes has the obvious advantage of teaching techniques applicable to new problems.

Chlorine-induced assembly of a cationic coordination cage with a μ5-carbonato-bridged Mn(II)24 core.

Science.gov (United States)

Xiong, Ke-Cai; Jiang, Fei-Long; Gai, Yan-Li; Yuan, Da-Qiang; Han, Dong; Ma, Jie; Zhang, Shu-Quan; Hong, Mao-Chun

2012-04-27

Chlorine caged in! The chlorine-induced assembly of six shuttlecock-like tetranuclear Mn(II) building blocks generated in situ based on p-tert-butylthiacalix[4]arene and facial anions gave rise to a novel truncated distorted octahedral cationic coordination cage with a μ(5)-carbonato-bridged Mn(II)(24) core. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Investigation of prototypal MOFs consisting of polyhedral cages with accessible Lewis-acid sites for quinoline synthesis.

Science.gov (United States)

Gao, Wen-Yang; Leng, Kunyue; Cash, Lindsay; Chrzanowski, Matthew; Stackhouse, Chavis A; Sun, Yinyong; Ma, Shengqian

2015-03-21

A series of prototypal metal-organic frameworks (MOFs) consisting of polyhedral cages with accessible Lewis-acid sites, have been systematically investigated for Friedländer annulation reaction, a straightforward approach to synthesizing quinoline and its derivatives. Amongst them MMCF-2 demonstrates significantly enhanced catalytic activity compared with the benchmark MOFs, HKUST-1 and MOF-505, as a result of a high-density of accessible Cu(II) Lewis acid sites and large window size in the cuboctahedral cage-based nanoreactor of MMCF-2.

Sampling the equilibrium kinetic network of Trp-cage in explicit solvent

NARCIS (Netherlands)

Du, W.; Bolhuis, P.G.

2014-01-01

We employed the single replica multiple state transition interface sampling (MSTIS) approach to sample the kinetic (un) folding network of Trp-cage mini-protein in explicit water. Cluster analysis yielded 14 important metastable states in the network. The MSTIS simulation thus resulted in a full 14

Effects of Changing to Individually Ventilated Caging on Guinea Pigs (Cavia porcellus).

Science.gov (United States)

Giral, Marta; Armengol, Clara; Sánchez-Gómez, Sonia; Gavaldà, Amadeu

2015-05-01

The goal of this study was to evaluate the effect of changing to IVC housing on guinea pigs by recording several physiologic parameters in guinea pigs housed sequentially in open-top cages (OTC) and IVC. To register heart rate and locomotor activity, 10 male Dunkin-Hartley guinea pigs implanted with telemetric transmitters were moved from OTC to new, freshly prepared OTC or IVC and subsequently monitored by telemetry during the 4 d after the first cage change. Body weight and food consumption were measured twice during the study. Comparison of data from OTC- and IVC-housed guinea pigs showed no relevant differences in heart rate (mean ± 1 SD; 213 ± 10 bpm and 207 ± 9 bpm, respectively) at any time point. In contrast, locomotor activity varied: whereas activity during the first 4 h after the change of cage type was greater in IVC-housed animals, that during the following 24 h was greater in OTC but was similar between groups thereafter. Animals housed in OTC consumed more food than did those in IVC and, under both conditions, consumption was statistically related to body weight changes. Together, these results show that a change to IVC housing induced only transient increases in locomotor activity in guinea pigs without a marked increase in heart rate but with a decrease in food consumption. Because decreased food consumption was the only stress-associated sign during the 4-d observation, longer studies are needed to ascertain the importance of this finding.

Automated home cage assessment shows behavioral changes in a transgenic mouse model of spinocerebellar ataxia type 17.

Science.gov (United States)

Portal, Esteban; Riess, Olaf; Nguyen, Huu Phuc

2013-08-01

Spinocerebellar Ataxia type 17 (SCA17) is an autosomal dominantly inherited, neurodegenerative disease characterized by ataxia, involuntary movements, and dementia. A novel SCA17 mouse model having a 71 polyglutamine repeat expansion in the TATA-binding protein (TBP) has shown age related motor deficit using a classic motor test, yet concomitant weight increase might be a confounding factor for this measurement. In this study we used an automated home cage system to test several motor readouts for this same model to confirm pathological behavior results and evaluate benefits of automated home cage in behavior phenotyping. Our results confirm motor deficits in the Tbp/Q71 mice and present previously unrecognized behavioral characteristics obtained from the automated home cage, indicating its use for high-throughput screening and testing, e.g. of therapeutic compounds. Copyright © 2013 Elsevier B.V. All rights reserved.

Distribution of Helicobacter pylori cagA, cagE and vacA in different ethnic groups in Kuala Lumpur, Malaysia.

Science.gov (United States)

Tan, Huck Joo; Rizal, Abdul Manaf; Rosmadi, Mohamed-Yusoff; Goh, Khean-Lee

2005-04-01

There is a geographic variation in Helicobacter pylori (HP) genotypes and virulence factors. Cytotoxin associated genes A (cagA) and E (cagE), and certain vacuolating cytotoxin (vacA) genotypes are associated with peptic ulcer disease (PUD). There is also a different prevalence of PUD among different ethnic groups in Malaysia. The present study compared the distribution of vacA alleles and cagA and cagE status in three ethnic groups residing in Kuala Lumpur, Malaysia, and their association with clinical outcome. All patients with cultured positive HP were recruited prospectively. DNA was extracted and polymerase chain reaction was carried out to determine the cagA and cagE status and vacA alleles. The results of 127 patients (72 men and 55 women) were included. The mean age was 55.53 +/- 12.52 years. The ethnic distribution was 59 Chinese, 38 Indian and 30 Malay patients. The predominant genotype was s1a among the Malay (76.6%) and Indian patients (71.0%), and s1c among the Chinese patients (66.1%). The vacA middle region sequence m1 was detected in 66.7% of Malay, 54.2% of Chinese and 76.3% of Indian patients. Of the Malay, Chinese and Indian patients, 76.6%, 86.4% and 86.8%, respectively, were cagA positive, and 70.0%, 39.0% and 81.6%, respectively, were cagE positve. HP cagA, cagE and vacA were not associated with PUD. There is a distinctive difference in the HP strains among the three ethnic groups in Malaysia. There was no association between cagA, cagE or vacA genotypes and clinical outcome in the patients. None of these markers are helpful in predicting the clinical presentation of a HP infection.

Net cages in fish farming: a scientometric analysis Tanques rede em piscicultura: uma análise cienciométrica

Directory of Open Access Journals (Sweden)

Juliana Déo Dias

2012-03-01

Full Text Available AIM: This study presents a scientometric analysis of studies on net cages in order to determine whether these studies are considering environmental issues or only seeking an increase in food production; METHODS: The survey of articles was accomplished using the Thomson Reuters Database (ISI Web of Knowledge, with "cage culture" and "net cage" as keywords. We selected 238 articles that were published between 1990 and 2009; RESULTS: There was a temporal increase in the number of articles published. These articles focused mainly on fish production and environmental impacts; CONCLUSION: The studies of net cages in fish farming mainly investigated fish production, although environmental issues relating to this recent human activity were also important. Policy makers should consider both sides of the coin (i.e., both the benefits and environmental impacts of fish production in regulation of this activity.OBJETIVO: O presente estudo teve como objetivo apresentar uma análise cienciométrica sobre os estudos de tanques rede, a fim de responder se estes estudos estão considerando as questões ambientais ou, apenas, buscam um aumento na produção de alimentos; MÉTODOS: O levantamento dos artigos foi realizado na base Thomson Reuters (ISI Web of Knowledge, sendo utilizadas "cage culture" e "net cage" como palavras-chave. Foram selecionados 238 artigos durante o período de 1990 a 2009; RESULTADOS: Houve um incremento temporal no número de artigos publicados. Esses artigos enfocaram, principalmente, na produção pesqueira e impactos ambientais; CONCLUSÃO: Os estudos de tanques rede abordaram, principalmente, produção pesqueira, entretanto, as questões ambientais também foram importantes nesta recente atividade humana. Os decisores políticos devem considerar ambos os lados da moeda, ou seja, benefícios e impactos ambientais da produção pesqueira, antes de regular esta atividade.

Highly selective and sensitive methanol gas sensor based on molecular imprinted silver-doped LaFeO3 core-shell and cage structures

Science.gov (United States)

Rong, Qian; Zhang, Yumin; Lv, Tianping; Shen, Kaiyuan; Zi, Baoye; Zhu, Zhongqi; Zhang, Jin; Liu, Qingju

2018-04-01

Silver-doped LaFeO3 molecularly imprinted polymers (SLMIPs) were synthesized by a sol-gel method combined with molecularly imprinted technology as precursors. The precursors were then used to prepare SLMIPs cage (SLM-cage) and SLMIPs core-shell (SLM-core-shell) structures by using a carbon sphere as the template and hydrothermal synthesis, respectively. The structures, morphologies, and surface areas of these materials were determined, as well as their gas-sensing properties and related mechanisms. The SLM-cage and SLM-core-shell samples exhibited good responses to methanol gas, with excellent selectivity. The response and optimum working temperature were 16.98 °C and 215 °C, 33.7 °C and 195 °C, respectively, with corresponding response and recovery times of 45 and 50 s (SLM-cage) and 42 and 57 s (SLM-core-shell) for 5 ppm methanol gas. Notably, the SLM-cage and SLM-core-shell samples exhibited lower responses (≤5 and ≤7, respectively) to other gases, including ethanol, ammonia, benzene, acetone, and toluene. Thus, these materials show potential as practical methanol detectors.

Red mason bees cannot compete with honey bees for floral resources in a cage experiment.

Science.gov (United States)

Hudewenz, Anika; Klein, Alexandra-Maria

2015-11-01

Intensive beekeeping to mitigate crop pollination deficits and habitat loss may cause interspecific competition between bees. Studies show negative correlations between flower visitation of honey bees (Apis mellifera) and wild bees, but effects on the reproduction of wild bees were not proven. Likely reasons are that honey bees can hardly be excluded from controls and wild bee nests are generally difficult to detect in field experiments. The goal of this study was to investigate whether red mason bees (Osmia bicornis) compete with honey bees in cages in order to compare the reproduction of red mason bees under different honey bee densities. Three treatments were applied, each replicated in four cages of 18 m³ with 38 red mason bees in all treatments and 0, 100, and 300 honey bees per treatment with 10-20% being foragers. Within the cages, the flower visitation and interspecific displacements from flowers were observed. Niche breadths and resource overlaps of both bee species were calculated, and the reproduction of red mason bees was measured. Red mason bees visited fewer flowers when honey bees were present. Niche breadth of red mason bees decreased with increasing honey bee density while resource overlaps remained constant. The reproduction of red mason bees decreased in cages with honey bees. In conclusion, our experimental results show that in small and isolated flower patches, wild bees can temporarily suffer from competition with honey bees. Further research should aim to test for competition on small and isolated flower patches in real landscapes.

The Stand-alone Heliostat; El Heliostato Autonomo

Energy Technology Data Exchange (ETDEWEB)

Garcia Navajas, G.; Egea Gea, A. [Ciemat. Madrid (Spain)

2000-07-01

The first Autonomous Heliostat has been developed by CIEMAT at PSA facilities in Almeria. This heliostat is an innovative approach to reducing the civil engineering work costs in heliostat fields of central tower plants. Channels, cables and other electric elements have been eliminated in the new heliostat. Thus, one 70-m''2, classical T glass/metal heliostat has been adapted to include all the new stand-alone concept components. A PV system is able to drive two sun-tracking DC motors between 5 and 24 Vdc, 0 and 15A. The heliostat communicates with the control room 400-m away by using a radio-modern working at 9600 baud. An anemometer, a wind switcher, light and ambient temperature sensors have been installed on the heliostat for self-protection decision-making. A PV panel integrated into the heliostat reflecting surface, eliminates cabling and other elements required for a conventional power supply. Communication lines between master control and local control have been replaced by radio-modern. Testing has validated the technical feasibility of the prototype and quantified the real consumption and efficiencies of new elements. The extra costs produced by the autonomous concepts are compared with the cost of civil work in conventional heliostat field. (Author) 8 refs.

The Stand-alone Heliostat; El Heliostato Autonomo

Energy Technology Data Exchange (ETDEWEB)

Garcia Navajas, G; Egea Gea, A [Ciemat. Madrid (Spain)

2000-07-01

The first Autonomous Heliostat has been developed by CIEMAT at PSA facilities in Almeria. This heliostat is an innovative approach to reducing the civil engineering work costs in heliostat fields of central tower plants. Channels, cables and other electric elements have been eliminated in the new heliostat. Thus, one 70-m''2, classical T glass/metal heliostat has been adapted to include all the new stand-alone concept components. A PV system is able to drive two sun-tracking DC motors between 5 and 24 Vdc, 0 and 15A. The heliostat communicates with the control room 400-m away by using a radio-modern working at 9600 baud. An anemometer, a wind switcher, light and ambient temperature sensors have been installed on the heliostat for self-protection decision-making. A PV panel integrated into the heliostat reflecting surface, eliminates cabling and other elements required for a conventional power supply. Communication lines between master control and local control have been replaced by radio-modern. Testing has validated the technical feasibility of the prototype and quantified the real consumption and efficiencies of new elements. The extra costs produced by the autonomous concepts are compared with the cost of civil work in conventional heliostat field. (Author) 8 refs.

A Modular Cage System Design for Continuous Medium to Large Scale In Vivo Rearing of Predatory Mites (Acari: Phytoseiidae

Directory of Open Access Journals (Sweden)

Juan Alfredo Morales-Ramos

2014-01-01

Full Text Available A new stackable modular system was developed for continuous in vivo production of phytoseiid mites. The system consists of cage units that are filled with lima beans,  Phaseolus lunatus, or red beans, P. vulgaris, leaves infested with high levels of the two-spotted spider mites, Tetranychus urticae. The cage units connect with each other through a connection cup, which also serves for monitoring and collection. Predatory mites migrate upwards to new cage units as prey is depleted. The system was evaluated for production of Phytoseiulus persimilis. During a 6-month experimental period, 20,894.9±10,482.5 (mean ± standard deviation predators were produced per week. The production consisted of 4.1±4.6% nymphs and 95.9±4.6% adults. A mean of 554.5±59.8 predatory mites were collected per harvested cage and the mean interval length between harvests was 6.57±6.76 days. The potential for commercial and experimental applications is discussed.

Fish cage culture catches on in Nepal | CRDI - Centre de recherches ...

International Development Research Centre (IDRC) Digital Library (Canada)

... for their children, unlike many rural communities in Nepal. And the role of women in decision-making has been strengthened. Women take part alongside the men in all activities, from cleaning and repairing the fish cages to participating in meetings of farmers'' associations, attending workshops, and marketing the catch.

Hydrogen Gas Production in a Stand-Alone Wind Farm

Directory of Open Access Journals (Sweden)

M. Naziry Kordkandy

2017-04-01

Full Text Available This paper is analyzing the operation of a stand-alone wind farm with variable speed turbines, permanent magnet synchronous generators (PMSG and a system for converting wind energy during wind speed variations. On this paper, the design and modeling of a wind system which uses PMSG’s to provide the required power of a hydrogen gas electrolyzer system, is discussed. This wind farm consists of three wind turbines, boost DC-DC converters, diode full bridge rectifiers, permanent magnet synchronous generators, MPPT control and a hydrogen gas electrolyzer system. The MPPT controller based on fuzzy logic is designed to adjust the duty ratio of the boost DC-DC converters to absorb maximum power. The proposed fuzzy logic controller assimilates, with (PSF MPPT algorithm which generally used to absorb maximum power from paralleled wind turbines and stores it in form of hydrogen gas. The system is modeled and its behavior is studied using the MATLAB software.

A Meta-Analytic Review of Stand-Alone Interventions to Improve Body Image.

Directory of Open Access Journals (Sweden)

Jessica M Alleva

Full Text Available Numerous stand-alone interventions to improve body image have been developed. The present review used meta-analysis to estimate the effectiveness of such interventions, and to identify the specific change techniques that lead to improvement in body image.The inclusion criteria were that (a the intervention was stand-alone (i.e., solely focused on improving body image, (b a control group was used, (c participants were randomly assigned to conditions, and (d at least one pretest and one posttest measure of body image was taken. Effect sizes were meta-analysed and moderator analyses were conducted. A taxonomy of 48 change techniques used in interventions targeted at body image was developed; all interventions were coded using this taxonomy.The literature search identified 62 tests of interventions (N = 3,846. Interventions produced a small-to-medium improvement in body image (d+ = 0.38, a small-to-medium reduction in beauty ideal internalisation (d+ = -0.37, and a large reduction in social comparison tendencies (d+ = -0.72. However, the effect size for body image was inflated by bias both within and across studies, and was reliable but of small magnitude once corrections for bias were applied. Effect sizes for the other outcomes were no longer reliable once corrections for bias were applied. Several features of the sample, intervention, and methodology moderated intervention effects. Twelve change techniques were associated with improvements in body image, and three techniques were contra-indicated.The findings show that interventions engender only small improvements in body image, and underline the need for large-scale, high-quality trials in this area. The review identifies effective techniques that could be deployed in future interventions.

Topotactic transformations of sodalite cages: synthesis and NMR study of mixed salt-free and salt-bearing sodalites.

Science.gov (United States)

Trill, Henning; Eckert, Hellmut; Srdanov, Vojislav I

2002-07-17

A series of mixed sodalite samples, Na(8)[Al(6)Si(6)O(24)]Br(x).(H(3)O(2))(2-x), with the unit cell stoichiometries varying in the 0 < x <2 region, was made by hydrothermal synthesis and subsequently transformed into Na(6+x)[Al(6)Si(6)O(24)]Br(x).(4H(2)O)(2-x) and Na(6+x)[Al(6)Si(6)O(24)]Br(x).circle(2-x) sodalites. Here, circle refers to an empty sodalite cage. The three series, referred hereafter to as the Br/basic, Br/hydro, and Br/dry series, were characterized by powder diffraction X-ray and by (23)Na, (27)Al, and (81)Br magic angle spinning (MAS) NMR and high-resolution triple quantum (TQ) MAS NMR spectroscopy. We determined that incorporation of Br(-) anions is 130 times more preferred than incorporation of H(3)O(2)(-) anions during the formation of sodalite cages, which permitted precise control of the halide content in the solid. Monotonic trends in chemical shifts were observed as a function of cage occupancy, reflecting continuous changes in structural parameters. A linear correlation between (81)Br chemical shift and lattice constant with a slope of -86 ppm/A was observed for all three series. Likewise, (23)Na chemical shifts for Na(+) cations in salt-bearing sodalite cages correlate linearly with the lattice constant. Both results indicate a universal dependence of the (23)Na and (81)Br chemical shifts on the Na-Br distance. The (27)Al chemical shifts of Br/basic and Br/hydro sodalites obey an established relation between delta(cs) and the average T-O-T bond angle of 0.72 ppm/degrees. Br/dry sodalites show two aluminum resonances, characterized by significantly different chemical shifts and quadrupolar interaction parameters. In that series, local symmetry distortions are evident from strong quadrupolar perturbations in the NMR spectra. P(Q) values for (27)Al vary between 0.8 MHz in Br/basic sodalites and 4.4 MHz in the Br/dry series caused by deviations from the tetrahedral symmetry of the salt-free sodalite cages. For (23)Na, P(Q) values of 0.8, 0

The effect of different cage tiers and age on egg performance, egg ...

African Journals Online (AJOL)

admOUjg

2014-10-04

Oct 4, 2014 ... ... and health benefits (Appleby, 1998; Rodenburg et al., 2005; Vits et al., 2005). .... All hens stayed healthy over the experimental period. No birds were ..... Effects of housing system (outdoor vs cages) and age of laying hens ...

An improved synchronous reference frame phase-locked loop for stand-alone variable speed constant frequency power generation systems

DEFF Research Database (Denmark)

Liu, Yi; Xu, Wei; Ke, Longzhang

2017-01-01

The phase-locked loop (PLL) based on conventional synchronous reference frame, i.e. dqPLL, is usually employed in grid-connected variable speed constant frequency (VSCF) power generation systems (PGSs). However, the voltage amplitude drop of stand-alone PGSs is often greater than that of the grid...

Individualized choice in prenatal diagnosis : the impact of karyotyping and standalone rapid aneuploidy detection on quality of life

NARCIS (Netherlands)

Boormans, E. M. A.; Birnie, E.; Oepkes, D.; Boekkooi, P. F.; Bonsel, G. J.; van Lith, J. M. M.

2010-01-01

Objective To assess the reasons and perceptions of women who are offered a choice between karyotyping and standalone rapid aneuploidy detection (RAD) and to compare the impact of both tests on anxiety and health-related quality of life Methods In this prospective comparative study, women undergoing

Management of marine cage aquaculture. Environmental carrying capacity method based on dry feed conversion rate.

Science.gov (United States)

Cai, Huiwen; Sun, Yinglan

2007-11-01

Marine cage aquaculture produces a large amount of waste that is released directly into the environment. To effectively manage the mariculture environment, it is important to determine the carrying capacity of an aquaculture area. In many Asian countries trash fish is dominantly used in marine cage aquaculture, which contains more water than pellet feed. The traditional nutrient loading analysis is for pellet feed not for trash fish feed. So, a more critical analysis is necessary in trash fish feed culturing areas. Corresponding to FCR (feed conversion rate), dry feed conversion rate (DFCR) was used to analyze the nutrient loadings from marine cage aquaculture where trash fish is used. Based on the hydrodynamic model and the mass transport model in Xiangshan Harbor, the relationship between the water quality and the waste discharged from cage aquaculture has been determined. The environmental carrying capacity of the aquaculture sea area was calculated by applying the models noted above. Nitrogen and phosphorus are the water quality parameters considered in this study. The simulated results show that the maximum nitrogen and phosphorus concentrations were 0.216 mg/L and 0.039 mg/L, respectively. In most of the sea area, the nutrient concentrations were higher than the water quality standard. The calculated environmental carrying capacity of nitrogen and phosphorus in Xiangshan Harbor were 1,107.37 t/yr and 134.35 t/yr, respectively. The waste generated from cage culturing in 2000 has already exceeded the environmental carrying capacity. Unconsumed feed has been identified as the most important origin of all pollutants in cage culturing systems. It suggests the importance of increasing the feed utilization and improving the feed composition on the basis of nutrient requirement. For the sustainable development of the aquaculture industry, it is an effective management measure to keep the stocking density and pollution loadings below the environmental carrying

Environmental impacts of producing bioethanol and biobased lactic acid from standalone and integrated biorefineries using a consequential and an attributional life cycle assessment approach.

Science.gov (United States)

Parajuli, Ranjan; Knudsen, Marie Trydeman; Birkved, Morten; Djomo, Sylvestre Njakou; Corona, Andrea; Dalgaard, Tommy

2017-11-15

This study evaluates the environmental impacts of biorefinery products using consequential (CLCA) and attributional (ALCA) life cycle assessment (LCA) approaches. Within ALCA, economic allocation method was used to distribute impacts among the main products and the coproducts, whereas within the CLCA system expansion was adopted to avoid allocation. The study seeks to answer the questions (i) what is the environmental impacts of process integration?, and (ii) do CLCA and ALCA lead to different conclusions when applied to biorefinery?. Three biorefinery systems were evaluated and compared: a standalone system producing bioethanol from winter wheat-straw (system A), a standalone system producing biobased lactic acid from alfalfa (system B), and an integrated biorefinery system (system C) combining the two standalone systems and producing both bioethanol and lactic acid. The synergy of the integration was the exchange of useful energy necessary for biomass processing in the two standalone systems. The systems were compared against a common reference flow: "1MJ EtOH +1kg LA ", which was set on the basis of products delivered by the system C. Function of the reference flow was to provide service of both fuel (bioethanol) at 99.9% concentration (wt. basis) and biochemical (biobased lactic acid) in food industries at 90% purity; both products delivered at biorefinery gate. The environmental impacts of interest were global warming potential (GWP 100 ), eutrophication potential (EP), non-renewable energy (NRE) use and the agricultural land occupation (ALO). Regardless of the LCA approach adopted, system C performed better in most of the impact categories than both standalone systems. The process wise contribution to the obtained environmental impacts also showed similar impact pattern in both approaches. The study also highlighted that the recirculation of intermediate materials, e.g. C 5 sugar to boost bioethanol yield and that the use of residual streams in the energy

Field-Cage Methodology for Evaluating Climatic Suitability for Introduced Wood-Borer Parasitoids: Preliminary Results from the Emerald Ash Borer System

Science.gov (United States)

Ulyshen, Michael D.; Duan, Jian J.; Bauer, Leah S.; Gould, Juli; Taylor, Phil; Bean, Dick; Holko, Carol; Driesche, Roy Van

2011-01-01

Field-cage methods were developed to evaluate the abilities of Tetrastichus planipennisi Yang (Hymenoptera: Eulophidae) and Spathius agrili Yang (Hymenoptera: Braconidae), biocontrol agents of Agrilus planipennis Fairmaire (Coleoptera: Buprestidae), to parasitize, develop and overwinter following three late-season releases at both a northern (Michigan) and a southern (Maryland) location within the current North American range of A. planipennis. In August, September and October of 2009, five young green ash trees were selected at each location. Tetrastichus planipennisi and S. agrili were each randomly assigned to one of two cages attached to each tree, surrounding separate sections of trunk in which late-instar A. planipennis had been inserted. The following April, the caged trunk sections were dissected to determine the fate of each A. planipennis larva and the developmental stages of all recovered parasitoid progeny. At both locations, T. planipennisi and S. agrili were able to parasitize hosts and successfully overwinter (i.e., reach adulthood the following spring). For T. planipennisi, successful parasitism (i.e., parasitoid progeny reached adulthood) occurred for all caged releases in Maryland, but only for the August and September releases in Michigan. At both locations, percent parasitism by T. planipennisi was higher in August and September than in October. For S. agrili, successful parasitism occurred for all caged releases in Maryland, but only for the August release in Michigan. In Maryland, percent parasitism by S. agrili in August and September was higher than in October. The caging method described here should be useful in determining the climatic suitability of other regions before proceeding with large-scale releases of either species and may have utility in other wood-borer parasitoid systems as well. PMID:22233133

Novel approach to the behavioural characterization of inbred mice: automated home cage observations.

Science.gov (United States)