WorldWideScience

Sample records for stalks hemp hurds

  1. Water Absorption Behavior of Hemp Hurds Composites

    Science.gov (United States)

    Stevulova, Nadezda; Cigasova, Julia; Purcz, Pavol; Schwarzova, Ivana; Kacik, Frantisek; Geffert, Anton

    2015-01-01

    In this paper, water sorption behavior of 28 days hardened composites based on hemp hurds and inorganic binder was studied. Two kinds of absorption tests on dried cube specimens in deionized water bath at laboratory temperature were performed. Short-term (after one hour water immersion) and long-term (up to 180 days) water absorption tests were carried out to study their durability. Short-term water sorption behavior of original hemp hurds composites depends on mean particle length of hemp and on binder nature. The comparative study of long-term water sorption behavior of composites reinforced with original and chemically modified hemp hurds in three reagents confirmed that surface treatment of filler influences sorption process. Based on evaluation of sorption curves using a model for composites based on natural fibers, diffusion of water molecules in composite reinforced with original and chemically modified hemp hurds is anomalous in terms of the Fickian behavior. The most significant decrease in hydrophility of hemp hurds was found in case of hemp hurds modified by NaOH and it relates to change in the chemical composition of hemp hurds, especially to a decrease in average degree of cellulose polymerization as well as hemicellulose content.

  2. Thermal Stress Effect on Density Changes of Hemp Hurds Composites

    Science.gov (United States)

    Schwarzova, Ivana; Cigasova, Julia; Stevulova, Nadezda

    2016-12-01

    The aim of this article is to study the behavior of prepared biocomposites based on hemp hurds as a filling agent in composite system. In addition to the filler and water, an alternative binder, called MgO-cement was used. For this objective were prepared three types of samples; samples based on untreated hemp hurds as a referential material and samples based on chemically (with NaOH solution) and physically (by ultrasonic procedure) treated hemp hurds. The thermal stress effect on bulk density changes of hemp hurds composites was monitored. Gradual increase in temperature led to composites density reduction of 30-40 %. This process is connected with mass loss of the adsorbed moisture and physically bound water and also with degradation of organic compounds present in hemp hurds aggregates such as pectin, hemicelluloses and cellulose. Therefore the changes in the chemical composition of treated hemp hurds in comparison to original sample and its thermal decomposition were also studied.

  3. Thermal Stress Effect on Density Changes of Hemp Hurds Composites

    Directory of Open Access Journals (Sweden)

    Schwarzova Ivana

    2016-12-01

    Full Text Available The aim of this article is to study the behavior of prepared biocomposites based on hemp hurds as a filling agent in composite system. In addition to the filler and water, an alternative binder, called MgO-cement was used. For this objective were prepared three types of samples; samples based on untreated hemp hurds as a referential material and samples based on chemically (with NaOH solution and physically (by ultrasonic procedure treated hemp hurds. The thermal stress effect on bulk density changes of hemp hurds composites was monitored. Gradual increase in temperature led to composites density reduction of 30-40 %. This process is connected with mass loss of the adsorbed moisture and physically bound water and also with degradation of organic compounds present in hemp hurds aggregates such as pectin, hemicelluloses and cellulose. Therefore the changes in the chemical composition of treated hemp hurds in comparison to original sample and its thermal decomposition were also studied.

  4. Sustainable Bio-Aggregate-Based Composites Containing Hemp Hurds and Alternative Binder

    Directory of Open Access Journals (Sweden)

    Nadezda Stevulova

    2018-02-01

    Full Text Available This experimental study was focused on the application of a surface-modified hemp- hurds aggregate into composites using an alternative binder of MgO-cement. This paper presents the results of the comparative study of the parameters (chemical and physico-chemical modification, and hardening time affecting the physical (density, thermal conductivity coefficient and water-absorption behavior and mechanical properties (compressive strength of the bio-aggregate-based composite. A test of the parameters of the bio-composite samples showed some differences, which were determined by the chemical and surface properties of the modified filler, and which affected the mechanisms of hardening. The bulk density values of the hemp hurd composites hardened for 28 days place this material in the lightweight category of composites. The values of water absorption and the thermal conductivity coefficient of bio-composites decreased, and the strength parameter increased with an increase in the hardening time. The lower values of compressive strength, water absorption, and thermal conductivity coefficient (except for the ethylenediaminetetraacetic-acid-treated filler were observed in composites based on fillers chemically treated with NaOH and Ca(OH2 compared to referential composites (based on original hemp hurds. This is related to changes in the chemical composition of hemp hurds after chemical modification. The composites with ultrasound-treated hemp hurds had the greatest strengths at each hardening time. This is related to pulping the bundles of fibers and forming a larger surface area for bonding in the matrix.

  5. Application of Hemp Hurds in the Preparation of Biocomposites

    Science.gov (United States)

    Cigasova, J.; Stevulova, N.; Schwarzova, I.; Sicakova, A.; Junak, J.

    2015-11-01

    Hemp is a controversial bio-product with promising performance as a sustainable building material. The fact that hemp is an organic, natural product makes it highly relevant in the present reality of global pollution and struggle for coping with planetary warming. The construction sector is among the leading industries when it comes to energy consumption, release of CO2; it is responsible for great amounts of waste and pollution. The research and implementation of sustainable building materials is a crucial necessity in the modern times. Hemp (Cannabis sativa) is an agricultural crop that can be used as a building material in combination with conventional or alternative binders. Hemp composites have many advantages as a building material, but it is not load-bearing and must be used in combination with a loadbearing wooden frame. Despite this disadvantage, hemp composite materials offer several of appropriate properties, namely: low density, good thermal insulation, antiseptic and breathability. This paper studies the possibility of preparing the lightweight composites based on hemp hurds (treated and/or untreated) as a filler and alternative MgO-cement as a binder. Properties of hemp composites are characterized by mechanical and physical methods.

  6. Preliminary Research Concerning Optimal Percentage of Hemp Hurds for Lining Panels and Filler Materials in Buildings

    Directory of Open Access Journals (Sweden)

    Maria - Adriana GHERGHISAN

    2013-03-01

    Full Text Available Composite materials for liningst and wall fillermade of hemp hurds and mineral binders represent again in recovery of mineral binders and use ofrepresent lignocellulosic fiber resulted afterprocessing.This paper aims to establish the optimumpercentual range of hemp hurds that can beembedded in ceramic mass, which is able to supportin various stages, the physical and dimensionalintegrity, manipulation, transport and during sandingresistance, the remaining viable recipes being theones that successfully pass this preliminary test. It isexpected for these samples to have comparablethermal and acoustic properties with similar industrialproducts, currently manufactured, which givesthepractical applicability of these composites.

  7. Relationship to reducing sugar production and scanning electron microscope structure to pretreated hemp hurd biomass (Cannabis sativa)

    International Nuclear Information System (INIS)

    Abraham, Reinu E.; Barrow, Colin J.; Puri, Munish

    2013-01-01

    Lignocellulosic biomass is a highly rigid and recalcitrant structure which requires pretreatment to loosen chemical bonds to make accessible monomeric sugars for biofuel production. In this study, locally available biomass, that is hemp (Cannabis sativa), a low cost feedstock for ethanol production, has been used for the production of fermentable sugars. Hemp hurd biomass (HHB) was exposed to five different pretreatments which included dilute acid (H 2 SO 4 ), alkaline (NaOH), alkaline peroxide, hot water and one stage dilute acid (H 2 SO 4 ). Different pretreatments resulted in loosening and degradation of HHB structure thus facilitating enzymatic saccharification at optimized parameters (pH–4.8 and 50 °C). The changes in the reactive groups (hydroxyl or acetyl) of the HHB were confirmed by attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy. Scanning electron microscopy (SEM) was employed to characterize the surface morphology of untreated and treated HHB. Finally, enzymatic saccharification demonstrated maximum yield of total sugars (743 mg g −1 ) that are suitable for biofuel production. -- Highlights: • Hemp hurd biomass (HHB) was used for producing fermentable sugars. • Alkaline pretreatment resulted in loosening and degradation of hemp structure. • Pretreated HHB was characterized using FTIR studies. • SEM studies evaluated the opening of fiber bundles in pretreatment, thereby increasing cellulose access to enzymes. • Enzymatic saccharification of pretreated HHB demonstrated maximum yield of reducing sugars

  8. Relationship to reducing sugar production and scanning electron microscope structure to pretreated hemp hurd biomass (Cannabis sativa)

    Energy Technology Data Exchange (ETDEWEB)

    Abraham, Reinu E.; Barrow, Colin J.; Puri, Munish

    2013-11-15

    Lignocellulosic biomass is a highly rigid and recalcitrant structure which requires pretreatment to loosen chemical bonds to make accessible monomeric sugars for biofuel production. In this study, locally available biomass, that is hemp (Cannabis sativa), a low cost feedstock for ethanol production, has been used for the production of fermentable sugars. Hemp hurd biomass (HHB) was exposed to five different pretreatments which included dilute acid (H{sub 2}SO{sub 4}), alkaline (NaOH), alkaline peroxide, hot water and one stage dilute acid (H{sub 2}SO{sub 4}). Different pretreatments resulted in loosening and degradation of HHB structure thus facilitating enzymatic saccharification at optimized parameters (pH–4.8 and 50 °C). The changes in the reactive groups (hydroxyl or acetyl) of the HHB were confirmed by attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy. Scanning electron microscopy (SEM) was employed to characterize the surface morphology of untreated and treated HHB. Finally, enzymatic saccharification demonstrated maximum yield of total sugars (743 mg g{sup −1}) that are suitable for biofuel production. -- Highlights: • Hemp hurd biomass (HHB) was used for producing fermentable sugars. • Alkaline pretreatment resulted in loosening and degradation of hemp structure. • Pretreated HHB was characterized using FTIR studies. • SEM studies evaluated the opening of fiber bundles in pretreatment, thereby increasing cellulose access to enzymes. • Enzymatic saccharification of pretreated HHB demonstrated maximum yield of reducing sugars.

  9. Sustainable hemp-based composites for the building industry application

    Science.gov (United States)

    Schwarzova, Ivana; Stevulova, Nadezda; Junak, Jozef; Hospodarova, Viola

    2017-07-01

    Sustainability goals are essential driving principles for the development of innovative materials in the building industry. Natural plant (e.g. hemp) fibers represent an attractive alternative as reinforcing material due to its good properties and sustainability prerequisites. In this study, hemp-based composite materials, designed for building application as non-load bearing material, providing both thermal insulation and physico-mechanical properties, are presented. Composite materials were produced by bonding hemp hurds with a novel inorganic binder (MgO-based cement) and then were characterized in terms of physical properties (bulk density, water absorption), thermal properties (thermal conductivity) and mechanical properties (compressive and tensile strength). The composites exhibited promising physical, thermal and mechanical characteristics, generally comparable to commercially available products. In addition, the hemp-based composites have the advantage of a significantly low environmental impact (thanks to the nature of both the dispersed and the binding phase) and no negative effects on human health. All things considered, the composite materials seem like very promising materials for the building industry application.

  10. Enrichment of Cellulosic Waste Hemp (Cannabis sativa Hurd into Non-Toxic Microfibres

    Directory of Open Access Journals (Sweden)

    Reinu E. Abraham

    2016-07-01

    Full Text Available In this study a largely available lignocellulose feedstock hemp (Cannabis sativa, obtained as an industrial waste, was used for cellulose extraction. The extraction of cellulose microfibres from hemp biomass was conducted by alkaline treatment and an acidification process. The extracted cellulose microfibres were characterised using Fourier-transformed infrared spectroscopy (FTIR, Scanning electron microscopy (SEM, thermogravimetric analysis (TGA and X-ray diffraction (XRD. The viability of the study was determined by growing human fibroblasts on the preparation which resulted in being non-toxic; indicating its potential in preparing biological scaffolds. Upon enzymatic hydrolysis of the cellulose microfibre using cellulase from Trichoderma reesei, a maximum of 909 mg/g of reducing sugars were obtained, which endorses its suitability for biofuel production.

  11. Byssinosis and COPD rates among factory workers manufacturing hemp and jute

    Directory of Open Access Journals (Sweden)

    Mukremin Er

    2016-02-01

    Full Text Available Objectives: Prior studies have been performed on cotton textile plants throughout the world. This study was planned to identify the rate of byssinosis and chronic obstructive pulmonary disease (COPD in hemp and jute workers and those who worked with both of them. Material and Methods: The study was realized in a factory which consecutively processed hemp and jute. The study enrollment included 266 people, 164 of whom were active workers and 102 were retired. A questionnaire, plain chest X-rays, physical examination and pulmonary function tests were performed. Dust levels were measured in various sections of the factory during 8 h work shifts. Endotoxin levels of various quality hemp fibers and dusts were measured. Results: The rate of byssinosis (28.2% was higher among the workers that who exposed to both jute and hemp dust. The frequency of chronic bronchitis in retired workers who previously smoked was higher (20% as compared to currently smoking workers (17%. High dust levels were measured in some parts of the factory (mean (M = 2.69 mg/m3. Working in dense dust areas, active smoking, being older than 40 years of age, being an ex-smoker, and working in the factory for a period exceeding 15 years were significantly associated with bronchitis and emphysema development. High endotoxin levels were determined for fine hemp dust (605 EU/mg, coarse hemp dust (336 EU/mg and poor quality hemp fibers (114 EU/mg, whereas in fresh hemp stalks the level of endotoxin was determined to be lower (0.27 EU/mg. Conclusions: Because of high exposures to jute and hemp dusts that are associated with high byssinosis rates, personal protection and environmental hygiene is crucial to prevention of byssinosis.

  12. Green insulation: hemp fibers

    Energy Technology Data Exchange (ETDEWEB)

    Anon,

    2011-09-15

    Indian hemp (Cannabis indica) is known for its psychotropic values and it is banned in most countries. However, industrial hemp (Cannabis sativa) is known for its tough fibers. Several manufactures in Europe including, small niche players, have been marketing hemp insulation products for several years. Hemp is a low environmental impact material. Neither herbicide nor pesticide is used during the growth of hemp. The fibers are extracted in a waste-free and chemical-free mechanical process. Hemp can consume CO2 during its growth. In addition, hemp fiber can be disposed of harmlessly by composting or incineration at the end of its life. Hemp fibers are processed and treated only minimally to resist rot and fungal activity. There is little health risk when producing and installing the insulation, thanks to the absence of toxic additive. Its thermal resistance is comparable to mineral wool. But the development and marketing of hemp fibers may be restricted in North America.

  13. Hygienic quality of stem fractions of mechanically processed fibre hemp and linseed

    Directory of Open Access Journals (Sweden)

    H-R. KYMÄLÄINEN

    2008-12-01

    Full Text Available Bast fibre is the most important fraction of bast fibre plants for technical products, i.e. thermal insulations and packaging materials. The hygienic quality of the various fractions of bast fibre plants is of interest in thermal insulations, because it may affect the quality of indoor air. Packaging materials may be associated e.g. with foodstuffs, which highlights the importance of hygienic quality. The aim of this study was to screen the hygienic quality, determined as microbial content, of mechanically fractionated fibre hemp and linseed plants harvested in the autumn before frost, after early frost and in spring. In addition, the possible correlation between microbes and ash was investigated. Two plant species, fibre hemp and linseed were studied. The plants were cultivated in Siuntio in southern Finland during the years 2002 and 2003, harvested in autumn or in spring and mechanically fractionated. The microbial contents of the fractions were examined by measuring the total number of microbes using Hygicult® growing slides. The microbial content of fractions of fibre hemp and linseed varied between 103 and 109 cfu/gdw. The fibre of hemp harvested after early frost or in spring had the lowest amount of moulds, but during winter and spring the amounts of bacteria and yeasts increased in hemp. Mechanically separated fibre and shive contained less microbes than the stalk. Ash contents of all examined samples of stems and stem fractions varied between 1% and 14%. The fibre after fractionating had a lower ash content (2.3–3.3% than that of stems (4.4–6.9% harvested in the autumn. The ash content of stem and shive decreased to 1.6% during winter, the ash content of fibre being even somewhat lower (0.9%. No correlation was observed between the contents of microbes and ash.;

  14. Hemp biofuel for automotive transport. Ukrainian perspective

    Directory of Open Access Journals (Sweden)

    Kolodnytska R.V.

    2016-08-01

    Full Text Available Ukraine takes a fourth place in the world in the technical hemp production and can use waste of hemp for biofuel (including biodiesel production. This paper presents an analysis of cetane numbers and low-temperature properties of hemp biodiesels as well as spray and evaporation of these fuels. Two types of hemp biodiesel fuels are analyzed: Hemp Methyl esters, produced from hemp oil in Ukraine (HM1 and European Union (HM2. It was found that hemp biodiesel has smaller cetane number than traditional rapeseed or soy biodiesel. At the same time hemp biodiesel shows better low-temperature properties compared with traditional biodiesels. So, it was recommended to use the mixture of rapeseed or soy biodiesel with hemp biodiesel to optimise both the low-temperature properties and cetane number of fuel. According to modelling the spray parameters of hemp biodiesel are very close to those of soy biodiesel. Evaporation of hemp biodiesel is very close to soy biodiesel according to previous research. Therefore, mixture of soy/rapeseed and hemp biodiesels can be recommended for experimental investigation as a future fuel for Ukrainian market.

  15. Hemp for textiles

    NARCIS (Netherlands)

    Westerhuis, W.

    2016-01-01

    Abstract

    Key words: Cannabis sativa L., day length sensitivity, fibre hemp, genotype, harvest time, plant density, plant weight, primary fibres, secondary fibres, sowing date, textiles.

    Westerhuis, W. (2016) Hemp for textiles: plant

  16. Revitalization of Industrial Hemp Cannabis sativa L. Var. sativa in Slovenia: a Study of Green Hemp Fibres

    Directory of Open Access Journals (Sweden)

    Rijavec Tatjana

    2017-03-01

    Full Text Available The importance of industrial hemp as a source of highly valuable textile fi bres is briefly presented through its use for textiles and composites and its increasing cultivated areas in the 21st century. On the territory of present Slovenia, about 160 ha of agricultural area was cultivated with hemp before WWII, then it quickly began to decline and at the end of the 1970s, it was no longer cultivated. Revitalization of industrial hemp in Slovenia with fi eld experiments started already in the years 2000/2001 for producing seeds, whereas hemp fi bres were used only as an insulation for buildings. The textile technological properties of hemp fi bres from diff erent varieties grown in Slovenia have not been examined till now. They are important for using hemp fibres in highly valuable textile products. The properties of green hemp fi bres extracted mechanically from non-retted hemp stems of Cannabis sativa L. var. sativa (varieties: Novosadska, Juso-11, Bialobrzeskie, Unico- B and Beniko were determined. All the analysed varieties except Beniko had stem height over 200 cm. The highest yield of green fibres was 33.1% (Novosadska. The analysed green fibres’ content was 1.24–3.26% of ash, 7.77–8.50% of moisture regain, 10.69–13.92% of water-soluble substances and 8.45–10.83% of pectin. Through a biodegradation process of retting green hemp fibres in tap water at temperature 35°C, 9.01– 18.89% of dry mass was removed after ten days. Average linear density of green hemp fi bres was very high, around 200 tex. Tenacity of fi bres’ bundles was in the range of 167–272 MPa, but tenacity of elementary fibres was 548–672 MPa. From the curves of specific stress-strain, it is seen that green hemp fibres from all five varieties had similar superstructure. All analysed green hemp fibres had high linear density and low mechanical properties. For textile application, they should be further processed into finer fibres in order to increase their

  17. Correlação entre os teores de líber e fibras em caules de crotalária e malva Correlation between bast and fiber content in sunn hemp and malva stalks

    Directory of Open Access Journals (Sweden)

    Anísio Azzini

    1986-01-01

    Full Text Available No presente estudo, estimou-se a correlação entre os teores de líber (casca e fibras em caules de crotalária (Crotalaria juncea L. e malva (Urena lobata L., com o objetivo de estabelecer um procedimento simples e rápido de análise de fibra. Os resultados obtidos mostraram que os teores de líber e fibra estão relacionados entre si, com alto nível de significância (p > 0,99 para as correlações entre essas duas características tecnológicas. Os coeficientes de correlação observados, de 0,84 e 0,79, respectivamente, para crotalária e malva, permitem a avaliação indireta do teor de fibra liberiana através do teor de líber, estabelecendo um procedimento simples e rápido de análise de fibra, a ser utilizado especificamente em programas de melhoramento genético.In this paper it was estimated the correlation between the bast and fiber contents in suns hemp (Crotalaria juncea L. and malva (Urena lobata L. stalks. The results showed that fiber contents are related with a high level of signification (p > 0.99 for the correlation between these two technological characteristics. The correlation coefficients observed were of 0.84 and 0.79, respectively to sunn hemp and malva. These high levels of correlation showed that the fiber content may be evaluated indirectly through the bast content, establishing a simple and rapid procedure for fiber determination of both species.

  18. Organosolv pulping and test paper characterization of fiber hemp

    NARCIS (Netherlands)

    Zomers, F.H.A.; Gosselink, R.J.A.; Dam, van J.E.G.; Tjeerdsma, B.F.

    1995-01-01

    The autocatalyzed ethanol pulping of hemp to produce chemical-grade pulp was examined. Batch delignification conditions were developed for hemp core, hemp bast, and hemp whole stem. Although successful pulping of both hemp core and bast fibre is possible, further research is necessary.

  19. Effect of pectin and hemicellulose removal from hemp fibres on the mechanical properties of unidirectional hemp/epoxy composites

    DEFF Research Database (Denmark)

    Liu, Ming; Meyer, Anne S.; Fernando, Dinesh

    2016-01-01

    The objective of this study was to investigate the effect of pectin and hemicellulose removal from hemp fibres on the mechanical properties of hemp fibre/epoxy composites. Pectin removal by EDTA and endo-polygalacturonase (EPG) removed epidermal and parenchyma cells from hemp fibres and improved...

  20. Oxidation of lignin in hemp fibres by laccase: effects on mechanical properties of hemp fibres and unidirectional fibre/epoxy composites

    DEFF Research Database (Denmark)

    Liu, Ming; Baum, Andreas; Odermatt, Jürgen

    2017-01-01

    Laccase activity catalyzes oxidation and polymerization of phenols. The effect of laccase treatment on the mechanical properties of hemp fibres and hemp fibre/epoxy composites was examined. Laccase treatment on top of 0.5% EDTA + 0.2% endo-polygalacturonase (EPG) treatments increased the mechanical...... properties of hemp fibres and fibre/epoxy composites. Comparing all fibre treatments, composites with 0.5% EDTA + 0.2% EPG + 0.5% laccase treated fibres had highest stiffness of 42 GPa and highest ultimate tensile strength (UTS) of 326 MPa at a fibre volume content of 50%. The thermal resistance of hemp...... hemp fibres and their composites were due to laccase catalyzed polymerization of lignin moieties in hemp fibres....

  1. HEMP emergency planning and operating procedures for electric power systems

    Energy Technology Data Exchange (ETDEWEB)

    Reddoch, T.W.; Markel, L.C. (Electrotek Concepts, Inc., Knoxville, TN (United States))

    1991-01-01

    Investigations of the impact of high-altitude electromagnetic pulse (HEMP) on electric power systems and electrical equipment have revealed that HEMP creates both misoperation and failures. These events result from both the early time E[sub 1] (steep-front pulse) component and the late time E[sub 3] (geomagnetic perturbations) component of HEMP. In this report a HEMP event is viewed in terms of its marginal impact over classical power system disturbances by considering the unique properties and consequences of HEMP. This report focuses on system-wide electrical component failures and their potential consequences from HEMP. In particular, the effectiveness of planning and operating procedures for electric systems is evaluated while under the influence of HEMP. This assessment relies on published data and characterizes utilities using the North American Electric Reliability Council's regions and guidelines to model electric power system planning and operations. Key issues addressed by the report include how electric power systems are affected by HEMP and what actions electric utilities can initiate to reduce the consequences of HEMP. The report also reviews the salient features of earlier HEMP studies and projects, examines technology trends in the electric power industry which are affected by HEMP, characterizes the vulnerability of power systems to HEMP, and explores the capability of electric systems to recover from a HEMP event.

  2. THE INFLUENCE OF ECOLOGICAL MATERIALS EMBEDDED INTO COMPOSITES UPON THE THERMAL INSULATING CAPACITY

    Directory of Open Access Journals (Sweden)

    Luminiţa-Maria BRENCI

    2014-12-01

    Full Text Available The paper presents the results of a research performed in order to design and manufacture composites that embed in their structure ecological raw materials, such as wood chips and hemp hurds. The thermal conductivity was determined for a temperature difference (ΔT of 200 C between the cold plate and warm plate and the measurements were done in eight points. The results showed that the best insulating composite material was obtained for the structure containing equal shares of wood chips and chopped hemp

  3. The influence of partial replacement of hemp shives by expanded perlite on physical properties of hemp-lime composite

    Science.gov (United States)

    Brzyski, Przemysław; Widomski, Marcin

    2017-07-01

    The use of waste plants in building materials production is consistent with the principles of sustainable development, including waste management, CO2 balance, biodegradability of the material e.g. after building demolition. The porous structure of plant materials determines their usability as the insulation materials. An example of plant applicable in the construction industry is the industrial hemp. The shives are produced from the wooden core of the hemp stem as lightweight insulating filler in the composite based on lime binder. The discussed hemp-lime composite, due to the presence of lightweight, porous organic aggregates exhibits satisfactory thermal insulation properties and is used as filling and insulation of walls (as well as roofs and floors) in buildings of the wooden frame construction. The irregular shape of shives and their low density causes nonhomogenous compaction of composite and the formation of voids between the randomly arranged shives. In this paper the series of hemp-lime composites were tested. Apart from hemp shives, an additional aggregate - expanded perlite was used as a fine, lightweight, thermal insulating filler. Application of the additional aggregate was aimed to fill the voids between hemp shives and to investigate its influence on the physical properties of composite: apparent density, total porosity, water absorption and thermal conductivity.

  4. Tensile properties of interwoven hemp/PET (Polyethylene Terephthalate) epoxy hybrid composites

    Science.gov (United States)

    Ahmad, M. A. A.; Majid, M. S. A.; Ridzuan, M. J. M.; Firdaus, A. Z. A.; Amin, N. A. M.

    2017-10-01

    This paper describes the experimental investigation of the tensile properties of interwoven Hemp/PET hybrid composites. The effect of hybridization of hemp (warp) with PET fibres (weft) on tensile properties was of interest. Hemp and PET fibres were selected as the reinforcing material while epoxy resin was chosen as the matrix. The interwoven Hemp/PET fabric was used to produce hybrid composite using a vacuum infusion process. The tensile test was conducted using Universal Testing Machine in accordance to the ASTM D638. The tensile properties of the interwoven Hemp/PET hybrid composite were then compared with the neat woven hemp/epoxy composite. The results show that the strength of hemp/PET with the warp direction was increased by 8% compared to the neat woven hemp composite. This enhancement of tensile strength was due to the improved interlocking structure of interwoven Hemp/PET hybrid fabric.

  5. Comparison of the cable coupling effects under two kinds of HEMP environment

    CERN Document Server

    Sun Bei Yun; Xie Yan Zhao

    2002-01-01

    There are various kinds of HEMP environment definitions. The coupling effects of electronic system are more different under different HEMP environment. The responds of cable of different length are investigated under 1976 HEMP and 1996 HEMP environment. The results indicate that the cable coupling effects under 1976 HEMP environment are more serious than those under 1996 HEMP environment

  6. Pretreatment of hemp fibers for utilization in strong biocomposite materials

    DEFF Research Database (Denmark)

    Liu, Ming

    Hemp is the common name for Cannabis sativa cultivated for industrial use. Compared to synthetic fibers (e.g. glass fiber), hemp fibers have many advantages such as low cost, low density (1.5 g/cm3) and high specific strength and stiffness. As a result of increasing environmental awareness......, interest in hemp fiber reinforced composites is increasing because of a high potential of manufacturing hemp fiber reinforced polymer composites with acceptable mechanical properties at low cost. In order to expedite the application of natural fibers in polymer composites, hemp fibers need to be treated...... before being incorporated in matrix polymers to optimize the properties of fibers and fiber reinforced composites. The overall objective of this study was therefore to focus on understanding the correlation between chemical composition and morphology of hemp fibers and mechanical properties of hemp...

  7. Stalking and Violence.

    Science.gov (United States)

    Ostermeyer, Britta; Friedman, Susan Hatters; Sorrentino, Renee; Booth, Brad D

    2016-12-01

    The three widely known stalker classifications assist in categorizing stalkers, which allows for better management of violence risk. Although 80% of stalking is done by men, women also engage in stalking, and their violence risk should not be underestimated. Juvenile stalkers do exist and juvenile stalking is also associated with violence. Clinicians can become a victim of stalking and may become victims of stalking by proxy, a special type of stalking behavior where the stalker involves other people or agencies to communicate with or track their victim. A careful stalking violence risk assessment is essential in the intervention and risk management process. Copyright © 2016 Elsevier Inc. All rights reserved.

  8. Hemp as an Agricultural Commodity

    Science.gov (United States)

    2014-02-14

    passed laws restricting legal production to medicinal and industrial purposes only.42 The 1937 Marihuana Tax Act defined hemp as a narcotic drug...refers to industrial hemp, “marijuana” (or “ marihuana ” as it is spelled in the older statutes) refers to the psychotropic drug (whether used for... medicinal or recreational purposes), and “cannabis” refers to the plant species that has industrial, medicinal , and recreational varieties.1 Comparison of

  9. Thermo-Insulation Properties Of Hemp-Based Products

    Directory of Open Access Journals (Sweden)

    Lekavicius V.

    2015-02-01

    Full Text Available As known, many multi-purpose plants can be used in different industries. This research is focused on the possibilities to utilize hemp as feedstock for thermal insulation products. The most advantageous features of hemp insulation are associated with health and environmental safety. The thermal conductivity of commercially available hemp insulation products is comparable with that of other fibrous insulation materials; however, it is possible to develop new products that could be more efficient in terms of cost and due to other important features.

  10. Agronomy and photosynthesis physiology of hemp (Cannabis sativa L.)

    NARCIS (Netherlands)

    Tang, Kailei

    2018-01-01

    Hemp (Cannabis sativa L.) is a sustainable high-yielding crop that delivers valuable fibres, seeds and psychoactive substances. However, there is a lack of field experimental data on the cultivation of hemp because its production was largely abandoned in the last century. Hemp is now

  11. New developments in fiber hemp (Cannabis sativa L.) breeding

    NARCIS (Netherlands)

    Salentijn, E.M.J.; Zhang, Qingying; Amaducci, Stefano; Yang, Ming; Trindade, L.M.

    2015-01-01

    Fiber hemp (Cannabis sativa L.) is a sustainable and high yielding industrial crop that can help to meet the high global demand for fibers. Hemp can be grown for fiber, seeds, and/or for dual purpose in a wide range of geographic zones and climates. Currently the main hemp producing regions in

  12. Microscopic Study on Hemp Bast Fibre Formation

    NARCIS (Netherlands)

    Hernandez, A.; Westerhuis, W.; Dam, van J.E.G.

    2007-01-01

    Commonly, fibre hemp (Cannabis sativa) is not considered for the production of soft and easy-care textiles. However, initial tests in the textile industry have shown that certain processes allow improvement in the everyday-wear characteristics of hemp textiles. In the framework of the EU R&D

  13. Hemp (Cannabis sativa L.) as an Environmentally Friendly Energyplant

    Science.gov (United States)

    Poisa, Liena; Adamovics, Aleksandrs

    2010-01-01

    Hemp is suitable as a renewable energy resource. The aim of this study was to clarify local hemp's (Cannabis sativa L.) possibilities for energy use. Arsenic (As), cadmium (Cd), lead (Pb) and titanium (Ti) presence in hemp was determined using an inductively coupled plasma optical emission spectrometer Optima 2100 DV. If there were increased N fertilizer rates, there were increased hemp `Pūriņi' seeds and shive yield increases, but the oil content was reduced. Arsenic content was higher in the shives than in the stems with fibre. The ash content depends on non-organic substances which the plants absorb during the vegetation season. The lignin content depends on several factors: plant parts, and the N fertilizer rate. The unexplored factors have a great effect on the ash and lignin content. Hemp is suitable for cultivation and for bio-energy production in the agro-climatic conditions in Latvia.

  14. La producción geosimbólica de Las Hurdes. Teoría, historia y práctica de un territorio imaginario

    OpenAIRE

    Matías Marcos, Juan David

    2017-01-01

    Esta Historia de La producción geosimbólica de Las Hurdes recurre a las herramientas de la geografía literaria y cultural y a las de la mitocrítica, la tematología y a imagología para trazar una geografía moral inspirada en el pensamiento cristiano y dividida en tres grandes continentes, correspondientes a las imágenes de la comarca como Paraíso, Purgatorio o Infierno. Para categorizar un capital simbólico que abarca desde el Barroco hasta la actualidad, la geografía moral de Las Hurdes se fr...

  15. Still special? Harvesting procedures for industrial hemp

    Directory of Open Access Journals (Sweden)

    Hans-Jörg Gusovius

    2016-01-01

    Full Text Available A multitude of different harvesting procedures is available after the re-approval of hemp growing in Germany about 20 years ago. Established, but as well recent machine developments enable the supply of raw materials for further processing or as food and feed materials. The necessary specialization level results in high but, compared to other established crops, not exceeding procedural costs. In this study, harvesting procedures and technologies are analyzed that are currently used under Northern European cultivation conditions. However, technological enhancements are still needed in order to improve the competitiveness of fibre hemp in the crop rotation as well as of hemp-based semi-finished and finished products.

  16. Key parameters analysis of hybrid HEMP simulator

    International Nuclear Information System (INIS)

    Mao Congguang; Zhou Hui

    2009-01-01

    According to the new standards on the high-altitude electromagnetic pulse (HEMP) developed by International Electrotechnical Commission (IEC), the target parameter requirements of the key structure of the hybrid HEMP simulator are decomposed. Firstly, the influences of the different excitation sources and biconical structures to the key parameters of the radiated electric field wave shape are investigated and analyzed. Then based on the influence curves the target parameter requirements of the pulse generator are proposed. Finally the appropriate parameters of the biconical structure and the excitation sources are chosen, and the computational result of the electric field in free space is presented. The results are of great value for the design of the hybrid HEMP simulator. (authors)

  17. HEMP emergency planning and operating procedures for electric power systems. Power Systems Technology Program

    Energy Technology Data Exchange (ETDEWEB)

    Reddoch, T.W.; Markel, L.C. [Electrotek Concepts, Inc., Knoxville, TN (United States)

    1991-12-31

    Investigations of the impact of high-altitude electromagnetic pulse (HEMP) on electric power systems and electrical equipment have revealed that HEMP creates both misoperation and failures. These events result from both the early time E{sub 1} (steep-front pulse) component and the late time E{sub 3} (geomagnetic perturbations) component of HEMP. In this report a HEMP event is viewed in terms of its marginal impact over classical power system disturbances by considering the unique properties and consequences of HEMP. This report focuses on system-wide electrical component failures and their potential consequences from HEMP. In particular, the effectiveness of planning and operating procedures for electric systems is evaluated while under the influence of HEMP. This assessment relies on published data and characterizes utilities using the North American Electric Reliability Council`s regions and guidelines to model electric power system planning and operations. Key issues addressed by the report include how electric power systems are affected by HEMP and what actions electric utilities can initiate to reduce the consequences of HEMP. The report also reviews the salient features of earlier HEMP studies and projects, examines technology trends in the electric power industry which are affected by HEMP, characterizes the vulnerability of power systems to HEMP, and explores the capability of electric systems to recover from a HEMP event.

  18. Fermented Dough Characteristics of Wheat-barley-hemp Composites. Comparison of Two Dosages of Barley and Hemp Wholemeal/Flour

    Directory of Open Access Journals (Sweden)

    Marie Hrušková

    2016-01-01

    Full Text Available Wheat flour substitution by barley one led to shortening of fermentation and leavening times (about 14–57% and 35–83%, respectively as well as to lessening of dough volumes (about 25–75%, based on lowered protein quality (Zeleny value. Addition of barley flour affected specific bread volume; diminishing for wheat-barley blends 70:30 and 50:50 reached 30% and 43%, respectively. Volume of bread prepared from wheat-barley blend 70:30 enhanced by dehulled hemp wholemeal was the highest within the tested tri-composites set, achieving 130% of wheat-barley control; other hemp products caused the parameter decrease (from 8 to 33%. Within a group of bakery products containing 50% of barley flour, hulled hemp wholemeal partially supressed negative effect of barley flour – specific bread volumes increased about ca 15%. Commercial fine hemp flour samples demonstrated a reversal influence – its addition resulted into lower buns size than wheat-barley control (about 3–34%. Between wheat flour and both groups of flour tri-composites, PCA confirmed differences in dough and bread technological quality. Specific bread volume could be predicted according to maturograph dough elasticity, dough or bread OTG volumes.

  19. Influence of accompanying substances of hemp fibres on their electric resistance

    Directory of Open Access Journals (Sweden)

    Pejić Biljana

    2006-01-01

    Full Text Available Hemp fibres belong to the group of natural, cellulose bast fibres. These fibres have exceptional properties such as: antimicrobial effect, absence of allergy effect, extraordinary sorption properties, good electro-physical properties (small static electricity in regard to other cellulose fibres as well as high values of breaking strength (the natural fibre with the highest strength. However, hemp fibres have some defects: heterogeneous chemical composition, large quantity of accompanying substances (lignin pectins, waxes and unsatisfactory fineness and eveness. It is possible to a great extent to eliminate or reduce, the defects of hemp fibres by of appropriate modification treatments. In order to determine the appropriate modification treatment of hemp fibres, the dependences between the chemical composition, fineness and electric resistance of hemp fibres were presented in this paper. In the experimental part of the paper, by the application of a procedure for the determination of the chemical composition, the accompanying supstances of hemp fibres were gradually removed. After each phase some fibrous substrates were separated. After that the fineness and electric resistance were determined. This experiment was conducted in order to define the influence of each component of hemp fibres on the fineness and electric resistance. In this paper, hemp fibres were modified by an aqueous solution of sodium hydroxide, under different conditions of modification. The influence of modification conditions on the fineness and electric resistance were studied.

  20. Crop physiology of fibre hemp (Cannabis sativa L.)

    NARCIS (Netherlands)

    Werf, van der H.

    1994-01-01

    Fibre hemp ( Cannabis sativa L.) may be an alternative to wood as a raw material for the production of paper pulp. The effects of enviromnental factors and cultural measures on the functioning, yield and quality of fibre hemp crops in the

  1. Chemical and physical modification of hemp fibres by steam explosion technology

    International Nuclear Information System (INIS)

    Sutka, Anna; Kukle, Silvija; Gravitis, Janis; Berzins, Agris

    2013-01-01

    In current research attempt has been made to analyse hemp fibres treated with steam explosion (SE) technology. Disintegration of hemp fibres separated from non-retted, dew-retted and dried stems of hemp ('Purini')[1] by alkali treatment and steam explosion (SE) were investigated. An average intensive SE in combination with the hydro-thermal and alkali after-treatment allows decreasing the diameter of hemp fibres and reduce the concentration of non-celluloses components, among them hemicelluloses, lignin, pectin, waxes and water [1;2

  2. Evaluation of Model Wheat/Hemp Composites

    Directory of Open Access Journals (Sweden)

    Ivan Švec

    2014-02-01

    Full Text Available Model cereal blends were prepared from commercial wheat fine flour and 5 samples of hemp flour (HF, including fine (2 of conventional form, 1 of organic form and wholemeal type (2 of conventional form. Wheat flour was substituted in 4 levels (5, 10, 15, 20%. HF addition has increased protein content independently on tested hemp flour form or type. Partial model cereal blends could be distinguished according to protein quality (Zeleny test values, especially between fine and wholemeal HF type. Both flour types affected also amylolytic activity, for which a relationship between hemp addition and determined level of Falling Number was confirmed for all five model cereal blends. Solvent retention capacity profiles (SRC of partial models were influenced by both HF form and type, as well as by its addition level. Between both mentioned groups of quality features, significant correlation were proved - relationships among protein content/quality and lactic acid SRC were verifiable on p <0.01 (-0.58, 0.91, respectively. By performed ANOVA, a possibility to distinguish the HF form used in model cereal blend according to the lactic acid SRC and the water SRC was demonstrated. Comparing partial cereal models containing fine and wholemeal hemp type, HF addition level demonstrated its impact on the sodium carbonate SRC and the water acid SRC. Normal 0 21 false false false CS JA X-NONE

  3. The Genetic Structure of Marijuana and Hemp.

    Science.gov (United States)

    Sawler, Jason; Stout, Jake M; Gardner, Kyle M; Hudson, Darryl; Vidmar, John; Butler, Laura; Page, Jonathan E; Myles, Sean

    2015-01-01

    Despite its cultivation as a source of food, fibre and medicine, and its global status as the most used illicit drug, the genus Cannabis has an inconclusive taxonomic organization and evolutionary history. Drug types of Cannabis (marijuana), which contain high amounts of the psychoactive cannabinoid Δ9-tetrahydrocannabinol (THC), are used for medical purposes and as a recreational drug. Hemp types are grown for the production of seed and fibre, and contain low amounts of THC. Two species or gene pools (C. sativa and C. indica) are widely used in describing the pedigree or appearance of cultivated Cannabis plants. Using 14,031 single-nucleotide polymorphisms (SNPs) genotyped in 81 marijuana and 43 hemp samples, we show that marijuana and hemp are significantly differentiated at a genome-wide level, demonstrating that the distinction between these populations is not limited to genes underlying THC production. We find a moderate correlation between the genetic structure of marijuana strains and their reported C. sativa and C. indica ancestry and show that marijuana strain names often do not reflect a meaningful genetic identity. We also provide evidence that hemp is genetically more similar to C. indica type marijuana than to C. sativa strains.

  4. Properties and nutritional value of wheat bread enriched by hemp products

    Directory of Open Access Journals (Sweden)

    Ivan Švec

    2015-08-01

    Full Text Available Hemp (Cannabis sativa is annual plant that is native to China and remained as important material for food, industrial  and medical purposes. As source of cannabinoids belongs to controversial, but due to its excellent nutritional profile, non-gluten protein, fat and fibre it has potential in bakery products. Addition of 5% - 20% of hemp press cake fine flour and fine wholemeal significantly increased dietary fibre content, but their influence on volume of laboratory baked bread was different. Reflecting actual dosage, both types of hemp press cake flour diminished bun sizes about 6% - 33%; volumes of bread containing hulled wholemeal were comparable to standard (mean 310 mL/100 g vs. 333 ml/100 g, respectively. Only dehulled wholemeal hemp form increased the bread specific volume (6% - 30%, especially as 10% fortification (434 mL/100 g. Six Canadian hemp products were added as 10% and 20% on wheat flour base, comprising fine hemp flour and coarse hemp powder, dehulled whole seeds, hulled hemp seeds with sea salt as well as 50% and 43% hemp protein concentrates (KP1-KP6, respectively. The higher level of KP1, KP2, KP5 and KP6, the lower bread specific volumes were determined (decrease about 9% - 48%. Soft increase in buns size caused by 10% and 20% KP3 (323 and 319 ml/100 g vs. 296 mL/100 g was insignificant. The effect of KP4 was reversely verifiable, magnifying the parameter about 25% and 17%, respectively. In terms of protein content in bread, a level 11.75% in wheat bread has risen to approx. 14.5% and 18.0% when 10% and 20% of KP3 and KP5, respectively, was included into bread recipe. All six Canadian hemp products increased dietary fibre content in bread, mainly owing to KP4 and both protein concentrates (up to 4 and 3 times, respectively. Incorporation of hemp flour up to the level of 10% positively affected bread sensorial properties.

  5. CHARACTERIZATION AND PERFORMANCE OF ELEMENTARY HEMP FIBRES: FACTORS INFLUENCING TENSILE STRENGTH

    Directory of Open Access Journals (Sweden)

    Mizi Fan

    2010-09-01

    Full Text Available This paper presents the outcomes from an extensive investigation on the structure and geometry of single hemp fibres, as well as configurations and related tensile strength (TS of hemp fibres, with the aid of field emission scanning and optical microscopy. The results showed that 1 the TS increased with the decrease of the diameter of individual test pieces, due possibly to the stacks of multiple single fibres within the test pieces; 2 shear failure between single fibres in a test pieces played a significant role in the test results; 3 the TS was closely related to the number of both the inherent joints along the fibre length and single fibres contained in the test pieces; 4 the splits along the length and width of hemp fibres may complicate the test results, and 5 the optimized treatment prior to decortications may double the TS of hemp fibres compared to a normal retting processing. Reliable TS of single hemp fibres have been derived by a power regression, and the predicted TS were verified with an excellent agreement with experimentally tested results. The tensile strain-stress plot was found to be linear for all hemp test pieces, showing that the behaviour of single hemp fibres obeys Hooke’s law.

  6. QUALITY OF HEMP SEED OIL DEPENDING ON ITS OBTAINING

    Directory of Open Access Journals (Sweden)

    Ladislav Staruch

    2010-07-01

    Full Text Available Hemp (Cannabis sativa L. is probably one of the oldest field crops used in nutrition, but also for the production of fibres for clothes, ropes or canvas. Cannabis sativa is one of the most spread species of cannabis which belongs to family Cannabinaceae. The seeds are important part of cannabis sativa, which contains high part of lipids and proteins. It provides also valuable essential fatty acids, carbohydrates, fiber, vitamins and minerals. Due to low content of THC is possible to produce valuable oil from seeds, which is used in cosmetic and food industry. The aim of this work was to evaluate composition of hemp seeds from one harvest, observe and compare quality of parameters both cold pressed hemp seed oil and hemp seed oil by CO2 extraction. Both oils are comparable in composition of fatty acids which follow from results of analyses. Also contents of sterols and moisture are similar in both oils. The saponification value is similar in both oils, conformable to as a iodine value. Also were found dissimilarities in colours, phospholipides, unsaponifiable matter, acid value and peroxide value. The cold pressed hemp seed oil contained lower values of unsaponifiable matter, colours and higher concentration of phospholipides and lower acid value. It is caused by influence of CO2. The oxidation stability of cold pressed hemp seed oil was four times higher than oil by CO2 extraction. doi:10.5219/32 

  7. Industrial Hemp in North America: Production, Politics and Potential

    Directory of Open Access Journals (Sweden)

    Jerome H. Cherney

    2016-11-01

    Full Text Available Most of the Western World banned the cultivation of Cannabis sativa in the early 20th century because biotypes high in ∆9-tetrahydrocannabinol (THC, the principal intoxicant cannabinoid are the source of marijuana. Nevertheless, since 1990, dozens of countries have authorized the licensed growth and processing of “industrial hemp” (cultivars with quite low levels of THC. Canada has concentrated on hemp oilseed production, and very recently, Europe changed its emphasis from fiber to oilseed. The USA, historically a major hemp producer, appears on the verge of reintroducing industrial hemp production. This presentation provides updates on various agricultural, scientific, social, and political considerations that impact the commercial hemp industry in the United States and Canada. The most promising scenario for the hemp industry in North America is a continuing focus on oilseed production, as well as cannabidiol (CBD, the principal non-intoxicant cannabinoid considered by many to have substantial medical potential, and currently in great demand as a pharmaceutical. Future success of the industrial hemp industry in North America is heavily dependent on the breeding of more productive oilseed cultivars, the continued development of consumer goods, reasonable but not overly restrictive regulations, and discouragement of overproduction associated with unrealistic enthusiasm. Changing attitudes have generated an unprecedented demand for the cannabis plant and its products, resulting in urgent needs for new legislative, regulatory, and business frameworks, as well as scientific, technological, and agricultural research.

  8. The toll of stalking: the relationship between features of stalking and psychopathology of victims.

    NARCIS (Netherlands)

    Blaauw, E.; Winkel, F.W.; Arensman, E.; Sheridan, L.; Freeve, A.

    2002-01-01

    Information on the psychological consequences of stalking on victims is scarce. The present study aimed to investigate whether stalking victims have a heightened prevalence of psychopathology and the extent to which symptom levels are associated with stalking features. Stalking victims (N = 241)

  9. Hemp: A more sustainable annual energy crop for climate and energy policy

    International Nuclear Information System (INIS)

    Finnan, John; Styles, David

    2013-01-01

    The objective of this study was to compare the fuel-chain greenhouse gas balance and farm economics of hemp grown for bioenergy with two perennial bioenergy crops, Miscanthus and willow, and two more traditional annual bioenergy crops, sugar beet and oil seed rape (OSR). The GHG burden of hemp cultivation is intermediate between perennial and traditional annual energy crops, but net fuel chain GHG abatement potential of 11 t/CO 2 eq./ha/year in the mid yield estimate is comparable to perennial crops, and 140% and 540% greater than for OSR and sugar beet fuel chains, respectively. Gross margins from hemp were considerably lower than for OSR and sugar beet, but exceeded those from Miscanthus when organic fertilizers were used and in the absence of establishment grants for the latter crop. Extrapolated up to the EU scale, replacing 25% of OSR and sugar beet production with hemp production could increase net GHG abatement by up to 21 Mt CO 2 eq./year. Hemp is a considerably more efficient bioenergy feedstock than the dominant annual energy crops. Integrated into food crop rotations, hemp need not compete with food supplies, and could provide an appealing option to develop more sustainable non-transport bioenergy supply chains. - Highlights: ► The GHG burden of hemp is intermediate between perennial and annual energy crops. ► Replacing 25% of OSR/beet with hemp could increase GHG abatement by 21 Mt/CO 2 eq./year. ► Hemp is a more efficient bioenergy feedstock than the dominant annual energy crops

  10. Effects of diets containing hemp seeds or hemp cake on fatty acid ...

    African Journals Online (AJOL)

    Esnart Mukumbo

    2018-02-23

    Feb 23, 2018 ... Council Directive, 2003) for fibre and oil production. ... fractions of hemp seed, soybean and sunflower seed have been determined at 19.7%, 7.8% and 0.5% .... (FAMES) were quantified by gas chromatography using a Varian ...

  11. Development of hemp fibre - PP nonwoven composites - Conference Paper

    CSIR Research Space (South Africa)

    Hargitai, H

    2005-09-01

    Full Text Available Non-woven mats from hemp and polypropylene fibres in various proportions were produced and hot pressed to make composite material. The effect of hemp fibre content and anisotropy in non-woven mats resulting from the carding technology were examined...

  12. The Genetic Structure of Marijuana and Hemp.

    Directory of Open Access Journals (Sweden)

    Jason Sawler

    Full Text Available Despite its cultivation as a source of food, fibre and medicine, and its global status as the most used illicit drug, the genus Cannabis has an inconclusive taxonomic organization and evolutionary history. Drug types of Cannabis (marijuana, which contain high amounts of the psychoactive cannabinoid Δ9-tetrahydrocannabinol (THC, are used for medical purposes and as a recreational drug. Hemp types are grown for the production of seed and fibre, and contain low amounts of THC. Two species or gene pools (C. sativa and C. indica are widely used in describing the pedigree or appearance of cultivated Cannabis plants. Using 14,031 single-nucleotide polymorphisms (SNPs genotyped in 81 marijuana and 43 hemp samples, we show that marijuana and hemp are significantly differentiated at a genome-wide level, demonstrating that the distinction between these populations is not limited to genes underlying THC production. We find a moderate correlation between the genetic structure of marijuana strains and their reported C. sativa and C. indica ancestry and show that marijuana strain names often do not reflect a meaningful genetic identity. We also provide evidence that hemp is genetically more similar to C. indica type marijuana than to C. sativa strains.

  13. The Genetic Structure of Marijuana and Hemp

    Science.gov (United States)

    Sawler, Jason; Stout, Jake M.; Gardner, Kyle M.; Hudson, Darryl; Vidmar, John; Butler, Laura; Page, Jonathan E.; Myles, Sean

    2015-01-01

    Despite its cultivation as a source of food, fibre and medicine, and its global status as the most used illicit drug, the genus Cannabis has an inconclusive taxonomic organization and evolutionary history. Drug types of Cannabis (marijuana), which contain high amounts of the psychoactive cannabinoid Δ 9-tetrahydrocannabinol (THC), are used for medical purposes and as a recreational drug. Hemp types are grown for the production of seed and fibre, and contain low amounts of THC. Two species or gene pools (C. sativa and C. indica) are widely used in describing the pedigree or appearance of cultivated Cannabis plants. Using 14,031 single-nucleotide polymorphisms (SNPs) genotyped in 81 marijuana and 43 hemp samples, we show that marijuana and hemp are significantly differentiated at a genome-wide level, demonstrating that the distinction between these populations is not limited to genes underlying THC production. We find a moderate correlation between the genetic structure of marijuana strains and their reported C. sativa and C. indica ancestry and show that marijuana strain names often do not reflect a meaningful genetic identity. We also provide evidence that hemp is genetically more similar to C. indica type marijuana than to C. sativa strains. PMID:26308334

  14. Industrial hemp as a potential bioenergy crop in comparison with kenaf, switchgrass and biomass sorghum.

    Science.gov (United States)

    Das, Lalitendu; Liu, Enshi; Saeed, Areej; Williams, David W; Hu, Hongqiang; Li, Chenlin; Ray, Allison E; Shi, Jian

    2017-11-01

    This study takes combined field trial, lab experiment, and economic analysis approaches to evaluate the potential of industrial hemp in comparison with kenaf, switchgrass and biomass sorghum. Agronomy data suggest that the per hectare yield (5437kg) of industrial hemp stem alone was at a similar level with switchgrass and sorghum; while the hemp plants require reduced inputs. Field trial also showed that ∼1230kg/ha hemp grain can be harvested in addition to stems. Results show a predicted ethanol yield of ∼82gallons/dry ton hemp stems, which is comparable to the other three tested feedstocks. A comparative cost analysis indicates that industrial hemp could generate higher per hectare gross profit than the other crops if both hemp grains and biofuels from hemp stem were counted. These combined evaluation results demonstrate that industrial hemp has great potential to become a promising regional commodity crop for producing both biofuels and value-added products. Copyright © 2017 Elsevier Ltd. All rights reserved.

  15. Technological and nutritional aspect of different hemp types addition: Comparison of flour and wholemeal effect

    Directory of Open Access Journals (Sweden)

    Marie Hrušková

    2015-01-01

    Full Text Available Addition of non-traditional raw-materials and flours into wheat flour follows contemporary trend of manufacturing nutritionally healthier fermented bakery products. Aim of the study follows this tendency, evaluating nutritional improvement of composite flour and baking potential of prepared wheat-hemp flour composites. Hemp products addition significantly increased both protein and dietary fibre contents. Between five types of hemp flour, differences were observed according to incorporated amount (wheat flour substitution from 5% to 20%. In composites containing 20% of hemp flour and dehulled hemp wholemeal, protein content increased to 14.9% and to 15.7%, respectively (compared to 12.5% proteins in control wheat flour. Dietary fibre content change was governed unequivocally by addition level for both hemp flour and hemp wholemeal. Hemp wholemeal affected the solvent retention capacity (SRC profile of the wheat flour used in a broader extent than hemp flour done, interacting moreover with addition level applied. Significant diminishing was measured for the sucrose and the lactic acid SRC, which describe physicochemical stage of starch and proteins in prepared composites. Addition of 5% and 20% of dehulled hemp wholemeal decreased the formed SRC from 112.0% to 102.3% and to 64.1%, and the latter SRC from 182.6% to 108.0 and to 78.3%, respectively. Smaller bread volume and worse shape were evaluated as the amount of hemp flour gradually increased; wholemeal form had more or less a positive effect. Correspondingly to that, crumb firmness measured by penetration test was found approximately half for hemp flour composite bread than for the hemp wholemeal ones.

  16. Intercropping of taro and sunn hemp with cutting periods during the cycle

    Directory of Open Access Journals (Sweden)

    João Nacir Colombo

    Full Text Available ABSTRACT Intercropping using legumes is one of the ways to protect the main crop, and in long term improve the physical and chemical properties of the soil. The aim of this work was to evaluate the intercropping of Colocasia esculenta (L. Schott (taro and the tropical legume Crotalaria juncea L. (sunn hemp, cutting sunn hemp at ten periods during the cycle. The experiment was carried out under field conditions between 09/23/2010 and 06/04/2011. It consisted of 11 treatments related to the 10 cutting times of sunn hemp (55, 70, 85,100, 115, 130, 145, 160, 190, and 220 days after sowing - DAS plus a control of taro with no sunn hemp. During the cycle, taro was evaluated for plant height and incidence of leaf burn. At the time of cutting the sunn hemp, the plant height, fresh and dry matter masses, and nutrient content of the biomass were calculated. During taro harvest, we evaluated the productivity of the mother rhizomes and classified the cormels. Taro plants shaded by sunn hemp showed a lower incidence of leaf burn. The sunn hemp cut from 145 DAS onwards affected the yield of comercial rhizomes and total and agroeconomic indexes. Sunn hemp cut up to 130 DAS provided better performance of taro, without compromising productivity and economic indicators, with the highest amounts of N and K observed in the biomass cut at 115 DAS.

  17. Investigation of mechanical properties of kenaf, hemp and E-glass fiber reinforced composites

    Science.gov (United States)

    Dinesh, Veena; Shivanand, H. K.; Vidyasagar, H. N.; Chari, V. Srinivasa

    2018-04-01

    Recently the use of fiber reinforced polymer composite in the automobile, aerospace overwhelming designing sectors has increased tremendously due to the ecological issues and health hazard possessed by the synthetic fiber during disposal and manufacturing. The paper presents tensile strength, flexural strength and hardness of kenaf-E glass-kenaf, hemp-E glass-hemp and kenaf-E glass-hemp fiber reinforced polyester composites. The composite plates are shaped according to the standard geometry and uni-axially loaded in order to investigate the tensile responses of each combination. In addition to the physical and mechanical properties, processing methods and application of kenaf and hemp fiber composites is also discussed.

  18. Evaluation of Hemp Root Bast as a New Material for Papermaking

    Directory of Open Access Journals (Sweden)

    Cheng Miao

    2013-11-01

    Full Text Available Industrial hemp is a non-wood fiber material that can be used for papermaking due to a high yield of hemp raw material and high-quality physical properties of its pulp. Hemp is already used as a raw material for papermaking and other industrial productions. The chemical composition of hemp root bast (HRB was analyzed. HRBs were pulped using a soda-anthraquinone (Soda-AQ process and bleached with oxygen (O, chlorine dioxide (D, and alkali (E using the bleaching sequence OD0ED1. The results showed that HRB can be a suitable raw material for papermaking; the HRB pulp had a high viscosity (893 mL g-1 and brightness (85.52% ISO-brightness.

  19. Crumb evaluation of bread with hemp products addition by means of image analysis

    Directory of Open Access Journals (Sweden)

    Ivan Švec

    2013-01-01

    Full Text Available Hemp flour composition (20–30% proteins, 7–13% fat and more than 40% saccharides is a precondition for its usage into non-traditional cereal products. Corresponding to the fact, that hemp proteins are represented mostly by edestin, a low-molecular globulin, technological behaviour of composites containing 5–20% of hemp flour is basically different. The effect was clearly reflected in specific bread volume decrease, comparing standard wheat bread vs. wheat-hemp one. Sensorial profile of such fortified product depends on hemp sample origin, the better one was observed for dehulled wholemeal hemp flour addition. Image analysis of black-white bread cut prints revealed increasing pore densities (up to about 74% at reversely diminishing mean cell areas (up to about 31% for bread altered by hulled wholemeal hemp flour. Comparing to wheat standard W2, crumb appearance of bread enhanced by 5% and 20% of dehulled hemp wholemeal was described by conversely lower cell density (11 and 9 vs. 13 pores per cm2 with verifiably larger cells (3.13 a 4.25 mm2 against 2.35 mm2. Specific bread volume and crumb penetration were significantly correlated to both cell density (r −0.69 and −0.65, respectively; P = 99.9 % and to cell mean area (0.79 and 0.69, respectively; P = 99.9 %.

  20. Microstructure and mechanical performance of modified mortar using hemp fibres and carbon nanotubes

    KAUST Repository

    Hamzaoui, Rabah

    2014-04-01

    Mechanical performance of modified mortar using hemp fibres is studied following various processing conditions. Hemp fibres combined with carbon nanotubes (CNT) are introduced in mortar and their effect is studied as function of curing time. The cement phase is replaced by different percentages of dry or wet hemp fibres ranging from 1.1. wt% up to 3.1. wt% whereas carbon nanotubes are dispersed in the aqueous solution. Our experimental results show that compressive and flexural strengths of wet fibres modified mortar are higher than those for dry hemp-mortar material. The achieved optimal percentage of wet hemp fibres is 2.1. wt% allowing a flexural strength higher than that of reference mortar. The addition of an optimal CNT concentration (0.01. wt%) combined with wet hemp has a reinforcing effect which turns to be related to an improvement of compressive and flexural strengths by 10% and 24%, respectively, in comparison with reference condition. © 2013 Elsevier Ltd.

  1. Mechanical-physical experimental tests on lime mortars and bricks reinforced with hemp

    Science.gov (United States)

    Formisano, Antonio; Dessı, Enzo; Landolfo, Raffaele

    2017-11-01

    Hemp is an agricultural product used for various applications. In the Civil Engineering field, only a limited use of this natural material, called the "green pig" since exploitation of all its constituent parts is allowed, has been done. For this reason, in the paper an experimental activity on lime mortars and bricks reinforced with hemp components has been performed. Compression and bending tests have been carried out on specimens manufactured with hemp shives and fibres, respectively. The achieved results have shown that hemp products change the failure modes from brittle to ductile, leaving basically unaltered the strength capacity of reinforced specimens with respect to unreinforced ones.

  2. New Green Polymeric Composites Based on Hemp and Natural Rubber Processed by Electron Beam Irradiation

    Directory of Open Access Journals (Sweden)

    Maria-Daniela Stelescu

    2014-01-01

    Full Text Available A new polymeric composite based on natural rubber reinforced with hemp has been processed by electron beam irradiation and characterized by several methods. The mechanical characteristics: gel fraction, crosslink density, water uptake, swelling parameters, and FTIR of natural rubber/hemp fiber composites have been investigated as a function of the hemp content and absorbed dose. Physical and mechanical properties present a significant improvement as a result of adding hemp fibres in blends. Our experiments showed that the hemp fibers have a reinforcing effect on natural rubber similar to mineral fillers (chalk, carbon black, silica. The crosslinking rates of samples, measured using the Flory-Rehner equation, increase as a result of the amount of hemp in blends and the electron beam irradiation dose increasing. The swelling parameters of samples significantly depend on the amount of hemp in blends, because the latter have hydrophilic characteristics.

  3. The Fear Factor: Exploring Predictors of Fear among Stalking Victims throughout the Stalking Encounter

    Science.gov (United States)

    Reyns, Bradford W.; Englebrecht, Christine M.

    2013-01-01

    The crime of stalking has received much research attention, yet there are still important questions to be explored surrounding this behavior. One such question relates to definitions of stalking, including the requirement that victims must express fear to qualify as victims of stalking. The current study addresses this issue by exploring the…

  4. Writing women into medical history in the 1930s: Kate Campbell Hurd-Mead and "medical women" of the past and present.

    Science.gov (United States)

    Appel, Toby A

    2014-01-01

    Kate Campbell Hurd-Mead (1867–1941), a leader among second-generation women physicians in America, became a pioneer historian of women in medicine in the 1930s. The coalescence of events in her personal life, the declining status of women in medicine, and the growing significance of the new and relatively open field of history of medicine all contributed to this transformation in her career. While she endeavored to become part of the community of male physicians who wrote medical history, her primary identity remained that of a “medical woman.” For Hurd-Mead, the history of women in the past not only filled a vital gap in scholarship but served practical ends that she had earlier pursued by other means—those of inspiring and advancing the careers of women physicians of the present day, promoting organizations of women physicians, and advocating for equality of opportunity in the medical profession.

  5. Simulation of hemp fibre bundle and cores using discrete element method

    Energy Technology Data Exchange (ETDEWEB)

    Al-Amin Sadek, M.; Chen, Y. [Manitoba Univ., Winnipeg, MB (Canada). Dept. of Biosystems Engineering; Lague, C. [Ottawa Univ., Ottawa, ON (Canada). Faculty of Engineering; Landry, H. [Prairie Agricultural Machinery Inst., Humboldt, SK (Canada); Peng, Q. [Manitoba Univ., Winnipeg, MB (Canada). Dept. of Mechanical and Manufacturing Engineering; Zhong, W. [Manitoba Univ., Winnipeg, MB (Canada). Dept. of Textile Sciences

    2010-07-01

    The mechanical behaviour of hemp fibre and core must be well understood in order to obtain high-grade hemp fibre that is currently in high demand for various industrial applications. Modelling by discrete element method can simulate the mechanical behaviour of such materials. A commercial discrete element software called Particle Flow Code was used in this study. In particular, the 3-dimension (PFC3D) was used to simulate hemp fibre and core. Since the basic PFC3D particles are spherical, the individual virtual hemp fibres were defined as strings of balls held together by PFC3D parallel bonds. The study showed that the virtual fibre is flexible and can bend and break by forces. This reflects the characteristics of hemp fibre. Using the clump logic of PFC3D, the virtual hemp core was defined as a rigid and unbreakable body, which reflect the characteristics of the core. The virtual fibre and core were defined with several microproperties, some of which were previously calibrated. The PFC3D bond properties were calibrated in this study. They included normal and shear stiffness; pb{sub k}n and pb{sub k}s; normal and shear strength; and bond disk radius, R of the virtual fibre. The calibration started with developing a PFC3D model to simulate fibre tensile test. The microproperties of virtual fibre and core were calibrated by running the PFC3D model. Literature data from fibre tensile tests was compared with simulation results.

  6. Analysis and Toxicological Evaluation of Cannabinoids in Hemp Food Products - a review

    OpenAIRE

    Lachenmeier, Dirk W.; Walch, Stephan G.

    2005-01-01

    After having abolished the prohibition of the cultivation of the species Cannabis sativa L. (so-called fibre hemp) with minor content of the psychoactive Δ9-tetrahydrocannabinol (THC), a wide variety of hemp food products is currently offered on the market. In this review, an introduction to the botany of the hemp plant and the current law situation in Germany and the European Union is presented. A survey of the analytic techniques used to verify compliance with the guidance values is given a...

  7. Stalking: Notion, characteristics and social responses

    Directory of Open Access Journals (Sweden)

    Nikolić-Ristanović Vesna

    2007-01-01

    Full Text Available In the last two decades stalking phenomenon is recognized and actualized in the world in professional, scientific circles, in media and the everyday talk. Recently, stalking is identified as specific and complex problem studied separately from domestic violence, workplace abuse, sexual harassment, threats, following, homicide, voyeurism and the other phenomenon to which stalking may or not be related. This paper is aimed to determine the notion of stalking and its relationship with similar phenomena, to review the research about the prevalence and nature of stalking, as well as to review the measures for its prevention, supporting victims and prosecution of offenders. Finally, the paper intend to contribute toward initiation of research and legal reforms regarding stalking victimisation in Serbia.

  8. Mechanical and thermal properties of polymer composite based on natural fibers: Moroccan hemp fibers/polypropylene

    International Nuclear Information System (INIS)

    Elkhaoulani, A.; Arrakhiz, F.Z.; Benmoussa, K.; Bouhfid, R.; Qaiss, A.

    2013-01-01

    Highlights: ► Moroccan hemp fibers are used as reinforcement in thermoplastic matrix. ► Moroccan hemp fiber was alkali treated to remove waxes and noncellulosic component. ► Fiber–matrix adhesion was assured by the use of a SEBS-g-MA as a compatibilizer. - Abstract: Moroccan hemp is a cellulosic fiber obtained from the north of Morocco. Their use as reinforcement in thermoplastic matrix composite requires a knowledge of their morphology and structure. In this paper the Moroccan hemp fiber was alkali treated to remove waxes and noncellulosic surface components. Fiber/matrix adhesion was assured by the use of a styrene-(ethylene-butene)-styrene three-block copolymer grafted with maleic anhydride (SEBS-g-MA) as a compatibilizer. Scanning electron microscopy (SEM), Fourier transforms infrared spectroscopy (FT-IR), Thermogravimetric analysis (TGA), tensile and torsional tests were carried out for hemp fibers polypropylene composite and the compatibilized composite at different fiber content. Thus, the binary composite PP/hemp fibers (Alk) and ternary system with maleic anhydride indicate clearly an improved adhesion of the fiber to the matrix as results of the good interaction at the interface. A gain of 50% on the Young’s modulus of PP/hemp 25 wt.% without coupling agent and 74% on the PP/hemp 20 wt.% composite with the coupling agent were found. Tensile strength curve shows a remarkable stabilization when the coupling agent was used

  9. Steam pretreatment of dry and ensiled industrial hemp for ethanol production

    Energy Technology Data Exchange (ETDEWEB)

    Sipos, Balint; Reczey, Kati [Budapest University of Technology and Economics, Department of Applied Biotechnology and Food Science, Szt. Gellert ter 4., H-1111 Budapest (Hungary); Kreuger, Emma; Bjoernsson, Lovisa [Lund University, Department of Biotechnology, P.O. Box 124, SE-221 00 Lund (Sweden); Svensson, Sven-Erik [Swedish University of Agricultural Sciences, Department of Agriculture - Farming Systems, Technology and Product Quality, P.O. Box 104, SE-230 53 Alnarp (Sweden); Zacchi, Guido [Lund University, Department of Chemical Engineering, P.O. Box 124, SE-221 00 Lund (Sweden)

    2010-12-15

    Biomass can be converted into liquid and gaseous biofuels with good efficiency. In this study, the conversion of industrial hemp (Cannabis sativa L.), a biomass source that can be cultivated with a high biomass yield per hectare, was used. Steam pretreatment of dry and ensiled hemp was investigated prior to ethanol production. The pretreatment efficiency was evaluated in terms of sugar recovery and polysaccharide conversion in the enzymatic hydrolysis step. For both materials, impregnation with 2% SO{sub 2} followed by steam pretreatment at 210 C for 5 min were found to be the optimal conditions leading to the highest overall yield of glucose. Simultaneous saccharification and fermentation experiments carried out with optimised pretreatment conditions resulted in ethanol yields of 163 g kg{sup -1} ensiled hemp (dry matter) (71% of the theoretical maximum) and 171 g kg{sup -1} dry hemp (74%), which corresponds to 206-216 l Mg{sup -1} ethanol based on initial dry material. (author)

  10. Phytomeliorative properties of Cannabis sativa L. plants depending on varietal features of the culture

    Directory of Open Access Journals (Sweden)

    В. М. Кабанець

    2017-12-01

    Full Text Available Purpose. To investigate the varietal characteristics of the hemp plants for improving the quality indices of the soil they grow in, determine the amount of inorganic elements in the soil, level of their accumulation in plant stalkі and seeds. Methods. Field and spectrometric methods were basic. The results were processed using conventional methods in agriculture, crop growing and statistics. Variants of the experiment were as follows: varieties ‘Hliana’, ‘Hlesiia’: 1 soils; 2 stalks; 3 seeds. Schemes of experiments included: a technical maturity of plants, row spacing 45 cm; b tech­nical maturity of plants, row spacing 15 cm; c biological maturity of plants, row spacing 45 cm; d biological maturity of plants, row spacing 15 cm. Results. The amount of the accumulation of alkaline earth metals and their compounds by seeds and stalks of hemp plants depending on their content in vegetation soils was determined. It was found that stalks of the ‘Hlesiia’ plant accumulated strontium (Sr and its compounds far less than that of ‘Hliana’, whereas in the seeds of the ‘Hlesiia’ variety the content of this chemical element was higher comparing with the previous variety by 70 and 78%, respectively. The difference in the accumulation of barium (Ba compounds in seeds of hemp plants was not significant, while the tissues of the plant stalks of the ‘Hlia­na’ variety accumulated its compounds significantly more as compared to the ‘Hlesiia’ variety. The degree of influence of the variety, feeding area and the maturity stage on the processes of magnesium compounds (Mg accumulation by plants was not revealed. Plants of the ‘Hlesiia’ variety accumulated far less calcium (Ca and its compounds in the stalk tissues as compared to the plants of the ‘Hliana’ variety: in variants of the technical maturity stage of plants with row spacing 45 cm (a and d – plants of narrow-row sowing (15 cm in the biological maturity stage 30,94 and 15

  11. Un Petroglifo con Inscripción en la Comarca de Las Hurdes (Cáceres

    Directory of Open Access Journals (Sweden)

    María Carmen SEVILLANO SAN JOSÉ

    2009-10-01

    Full Text Available El día 20 de octubre del año 1974, un equipo del Seminario de Arqueología de Salamanca, compuesto por: Carmen y Jesús Jordá Pardo, Ramón Grande, M.a Cleofé Rivero, Julián Bécares (a los que agradezco su colaboración por la ayuda prestada al realizar los calcos y fotografías y la firmante de este artículo, realizó un viaje por la comarca de las Hurdes a fin de comprobar la existencia de una posible cueva con pinturas rupestres.

  12. Un Petroglifo con Inscripción en la Comarca de Las Hurdes (Cáceres)

    OpenAIRE

    Sevillano San José, María Carmen

    2009-01-01

    El día 20 de octubre del año 1974, un equipo del Seminario de Arqueología de Salamanca, compuesto por: Carmen y Jesús Jordá Pardo, Ramón Grande, M.a Cleofé Rivero, Julián Bécares (a los que agradezco su colaboración por la ayuda prestada al realizar los calcos y fotografías) y la firmante de este artículo, realizó un viaje por la comarca de las Hurdes a fin de comprobar la existencia de una posible cueva con pinturas rupestres.

  13. Characterization and biological depectinization of hemp fibers originating from different stem sections

    DEFF Research Database (Denmark)

    Liu, Ming; Fernando, Dinesh; Meyer, Anne S.

    2015-01-01

    The wide variation of mechanical properties of natural fibers limits their applications in matrix compos-ites. The aim of this study is to evaluate the properties of hemp fibers from different stem sections (top,middle and bottom) and to assess fungal retting pretreatment of hemp from different...... stem sections withthe white rot fungi Phlebia radiata Cel 26 and Ceriporiopsis subvermispora. For the untreated hemp fibers,no apparent difference in tensile behavior for fiber bundles from different stem sections was observed,and more than 90% tested samples demonstrated plastic flow behavior. Fiber...... strength and stiffness werehighest for the fibers from the top and middle stem sections. These properties were related to the compositional make up and morphological properties of hemp fibers, notably the secondary fiber cell contents.In fungal retting, there was a strong dependence of depectinization...

  14. Thermal and mechanical properties of NaOH treated hemp fabric and calcined nanoclay-reinforced cement nanocomposites

    International Nuclear Information System (INIS)

    Hakamy, A.; Shaikh, F.U.A.; Low, I.M.

    2015-01-01

    Highlights: • Fabrication of nanoclay and hemp fabric-reinforced cement composites. • The optimum nanoclay and hemp fabric content is 1.0 and 6.9 wt.% respectively. • Surface-treated hemp fabric-reinforced cement composites demonstrated better mechanical properties. • Surface modification of hemp fabric was effective in improving the hemp fabric-cement matrix adhesion. - Abstract: Cement nanocomposites reinforced with hemp fabrics and calcined nanoclay (CNC) have been fabricated and investigated. CNC is prepared by heating nanoclay (Cloisite 30B) at 900 °C for 2 h. The influences of CNC dispersion on the mechanical properties and thermal properties of these composites have been characterized in terms of porosity, density, water absorption, flexural strength, fracture toughness, impact strength and thermal stability. The microstructure is investigated using Quantitative X-ray Diffraction Analysis (QXDA) and High Resolution Transmission Electron Microscopy (HRTEM). The effects of alkali (NaOH) treatment of hemp fabric on the mechanical properties of hemp fabric-reinforced cement composites with different fabric contents of 4.5, 5.7, 6.9 and 8.1 wt% are also investigated. Results show that the optimum hemp fabric content is 6.9 wt% (i.e. 6 fabric layers). Results also indicated that physical, mechanical and thermal properties were enhanced due to the addition of CNC into the cement matrix and the optimum content of CNC was 1 wt%. The treated hemp fabric-reinforced nanocomposites containing 1 wt% CNC exhibited the highest flexural strength, fracture toughness, impact strength and thermal stability by virtue of good fibre–matrix interface. This environmentally friendly nanocomposite can be used for various construction applications such as ceilings and roofs

  15. Multicellular stalk-like structures in Saccharomyces cerevisiae

    International Nuclear Information System (INIS)

    Engelberg, D.; Mimran, A.; Martinetto, H.; Otto, J.; Simchen, G.; Karin, M.; Fink, G.R.

    1998-01-01

    Stalk formation is a novel pattern of multicellular organization. Yeast cells which survive UV irradiation form colonies that grow vertically to form very long (0.5 to 3.0 cm) and thin (0.5 to 4 mm in diameter) multicellular structures. We describe the conditions required to obtain these stalk-like structures reproducibly in large numbers. Yeast mutants, mutated for control of cell polarity, developmental processes, UV response, and signal transduction cascades were tested and found capable of forming stalk-like structures. We suggest a model that explains the mechanism of stalk formation by mechanical environmental forces. We show that other microorganisms (Candida albicans, Schizosaccharomyces pombe, and Escherichia coli) also form stalks, suggesting that the ability to produce stalks may be a general property of microorganisms. Diploid yeast stalks sporulate at an elevated frequency, raising the possibility that the physiological role of stalks might be disseminating spores

  16. Properties of hemp fibre polymer composites - An optimisation of fibre properties using novel defibration methods and fibre characterisation

    DEFF Research Database (Denmark)

    Thygesen, Anders

    2006-01-01

    Characterization of hemp fibres was carried out with fibres obtained with low handling damage and defibration damage to get an indication of how strong cellulose based fibres that can be produced from hemp. Comparison was made with hemp yarn producedunder traditional conditions where damage...... obtained by steam explosion of hemp fibres prior defibrated with pectin degrading enzymes. The S2 layer in the fibre wall of the hemp fibres consisted of1-4 cellulose rich and lignin poor concentric layers constructed of ca. 100 nm thick lamellae. The microfibril angle showed values in the range 0......-10° for the main part of the S2-layer and 70-90° for the S1-layer. The microfibrils that are mainly parallelwith the fibre axis explain the high fibre stiffness, which in defibrated hemp fibres reached 94 GPa. The defibrated hemp fibres had higher fibre stiffness (88-94 GPa) than hemp yarn (60 GPa), which...

  17. Silica Treatments: A Fire Retardant Strategy for Hemp Fabric/Epoxy Composites

    Directory of Open Access Journals (Sweden)

    Francesco Branda

    2016-08-01

    Full Text Available In this paper, for the first time, inexpensive waterglass solutions are exploited as a new, simple and ecofriendly chemical approach for promoting the formation of a silica-based coating on hemp fabrics, able to act as a thermal shield and to protect the latter from heat sources. Fourier Transform Infrared (FTIR and solid-state Nuclear Magnetic Resonance (NMR analysis confirm the formation of –C–O–Si– covalent bonds between the coating and the cellulosic substrate. The proposed waterglass treatment, which is resistant to washing, seems to be very effective for improving the fire behavior of hemp fabric/epoxy composites, also in combination with ammonium polyphosphate. In particular, the exploitation of hemp surface treatment and Ammonium Polyphosphate (APP addition to epoxy favors a remarkable decrease of the Heat Release Rate (HRR, Total Heat Release (THR, Total Smoke Release (TSR and Specific Extinction Area (SEA (respectively by 83%, 35%, 45% and 44% as compared to untreated hemp/epoxy composites, favoring the formation of a very stable char, as also assessed by Thermogravimetric Analysis (TGA. Because of the low interfacial adhesion between the fabrics and the epoxy matrix, the obtained composites show low strength and stiffness; however, the energy absorbed by the material is higher when using treated hemp. The presence of APP in the epoxy matrix does not affect the mechanical behavior of the composites.

  18. A Method for Producing Microcrystalline Cellulose from Hemp Fibers

    Directory of Open Access Journals (Sweden)

    Valerii A. Barbash

    2018-03-01

    Conclusions. The proposed technology for the MCC production from hemp fibers reduces the cost of finished products by eliminating the bleaching stage of pulp as well as due to the use of domestic renewable plant raw materials, in particular hemp fibers compared with imported cotton or softwood pulp. The obtained MCC meets the requirements of technical conditions and can be used in the chemical industry as a sorbent or filler in the production of plastics and a water stabilizer for paints and emulsions.

  19. Viking and early Middle Ages northern Scandinavian textiles proven to be made with hemp.

    Science.gov (United States)

    Skoglund, G; Nockert, M; Holst, B

    2013-10-18

    Nowadays most plant textiles used for clothing and household are made of cotton and viscose. Before the 19th century however, plant textiles were mainly made from locally available raw materials, in Scandinavia these were: nettle, hemp and flax. It is generally believed that in Viking and early Middle Ages Scandinavia hemp was used only for coarse textiles (i.e. rope and sailcloth). Here we present an investigation of 10 Scandinavian plant fibre textiles from the Viking and Early Middle Ages, believed to be locally produced. Up till now they were all believed to be made of flax. We show that 4 textiles, including two pieces of the famous Överhogdal Viking wall-hanging are in fact made with hemp (in three cases hemp and flax are mixed). This indicates that hemp was important, not only for coarse but also for fine textile production in Viking and Early Middle Ages in Scandinavia.

  20. Viking and Early Middle Ages Northern Scandinavian Textiles Proven to be made with Hemp

    Science.gov (United States)

    Skoglund, G.; Nockert, M.; Holst, B.

    2013-10-01

    Nowadays most plant textiles used for clothing and household are made of cotton and viscose. Before the 19th century however, plant textiles were mainly made from locally available raw materials, in Scandinavia these were: nettle, hemp and flax. It is generally believed that in Viking and early Middle Ages Scandinavia hemp was used only for coarse textiles (i.e. rope and sailcloth). Here we present an investigation of 10 Scandinavian plant fibre textiles from the Viking and Early Middle Ages, believed to be locally produced. Up till now they were all believed to be made of flax. We show that 4 textiles, including two pieces of the famous Överhogdal Viking wall-hanging are in fact made with hemp (in three cases hemp and flax are mixed). This indicates that hemp was important, not only for coarse but also for fine textile production in Viking and Early Middle Ages in Scandinavia.

  1. Microstructure and mechanical performance of modified mortar using hemp fibres and carbon nanotubes

    KAUST Repository

    Hamzaoui, Rabah; Guessasma, Sofiane; Mecheri, Boubakeur; Eshtiaghi, Amir M.; Bennabi, Abdelkrim

    2014-01-01

    Mechanical performance of modified mortar using hemp fibres is studied following various processing conditions. Hemp fibres combined with carbon nanotubes (CNT) are introduced in mortar and their effect is studied as function of curing time

  2. Mechanical performance of hemp fiber polypropylene composites at different operating temperatures

    Science.gov (United States)

    Mehdi Tajvidi; Nazanin Motie; Ghonche Rassam; Robert H. Falk; Colin Felton

    2010-01-01

    In order to quantify the effect of temperature on the mechanical properties of hemp fiber polypropylene composites, formulations containing 25% and 40% (by weight) hemp fiber were produced and tested at three representative temperatures of 256, 296, and 336 K. Flexural, tensile, and impact tests, as well as dynamic mechanical analysis, were performed and the reduction...

  3. Adolescent stalking and risk of violence✩

    Science.gov (United States)

    Smith-Darden, Joanne P.; Reidy, Dennis E.; Kernsmith, Poco D.

    2018-01-01

    Stalking perpetration and the associated risk for violence among adolescents has generally been neglected. In the present study, 1236 youth completed surveys assessing empirically established stalking indicators, threats and aggression toward stalking victims, dating violence, and violent delinquency. Latent Profile Analysis identified 3 latent classes of boys: non-perpetrators (NP), hyper-intimate pursuit (HIP), and comprehensive stalking perpetrators (CSP) and, and 2 classes for girls: NP and HIP. Boys in the CSP class were the most violent youth on nearly all indices with boys in the HIP class demonstrating an intermediate level of violence compared to NP boys. Girls in the HIP class were more violent than NP girls on all indices. These findings suggest stalking in adolescence merits attention by violence prevention experts. In particular, juvenile stalking may signify youth at risk for multiple forms of violence perpetrated against multiple types of victims, not just the object of their infatuation. PMID:27641644

  4. Stalking: Criminological and criminal law aspects

    Directory of Open Access Journals (Sweden)

    Dimovski Darko

    2016-01-01

    Full Text Available Starting from the historical aspects of stalking crime, the author first provides an overview of different definitions of this socially negative behavior in the legal documents of countries where such conduct was first criminalized. The author presents statistical data on the scope of stalking in the United States and Australia. The second part of the paper discusses different types of stalkers, whose distinctive features are analyzed in more detail. In particular, the author focuses on the causal link between the stalking crime and violence, as well as the victims' responses to their own victimization. In the next part of this article, the author provides a detailed analysis of a wide range of consequences of stalking crime. In some cases, the victim of stalking may become the perpetrator of a criminal act of murder, whereas the stalker becomes a victim of this serious form of homicide. Although these cases are not numerous, they call for further analysis and proposing new legal solutions related to the privileged forms of murder, which are aimed at improving the position of the victim of stalking who is the perpetrator of such homicide. Finally, the author argues in favour of incriminating a new type of felony - the crime of stalking (in line with the model envisaged in the criminal legislation of the Republic of Croatia, as well as a privileged homicide which may be designated as a murder of a stalker committed by a victim of stalking.

  5. Alkaline hemp woody core pulping : impregnation characteristics, kinetic modelling and papermaking qualities

    NARCIS (Netherlands)

    Groot, de B.

    1998-01-01

    The aim of this thesis is to elucidate alkaline processing of hemp woody core, supporting the development and optimization of an efficient and non-polluting pulping process. This study has been a constituent of an integral programme to study fibre hemp.

    It is known that

  6. New ACE-Inhibitory Peptides from Hemp Seed (Cannabis sativa L.) Proteins.

    Science.gov (United States)

    Orio, Lara P; Boschin, Giovanna; Recca, Teresa; Morelli, Carlo F; Ragona, Laura; Francescato, Pierangelo; Arnoldi, Anna; Speranza, Giovanna

    2017-12-06

    A hemp seed protein isolate, prepared from defatted hemp seed meals by alkaline solubilization/acid precipitation, was subjected to extensive chemical hydrolysis under acid conditions (6 M HCl). The resulting hydrolysate was fractionated by semipreparative RP-HPLC, and the purified fractions were tested as inhibitors of angiotensin converting enzyme (ACE). Mono- and bidimensional NMR experiments and LC-MS analyses led to the identification of four potentially bioactive peptides, i.e. GVLY, IEE, LGV, and RVR. They were prepared by solid-phase synthesis, and tested for ACE-inhibitory activity. The IC 50 values were GVLY 16 ± 1.5 μM, LGV 145 ± 13 μM, and RVR 526 ± 33 μM, confirming that hemp seed may be a valuable source of hypotensive peptides.

  7. Experimental Investigation on Mechanical Properties of Hemp/E-Glass Fabric Reinforced Polyester Hybrid Composites

    Directory of Open Access Journals (Sweden)

    M R SANJAY

    2016-09-01

    Full Text Available This research work has been focusing on Hemp fibers has an alternative reinforcement for fiber reinforced polymer composites due to its eco-friendly and biodegradable characteristics. This work has been carried out to evaluate the mechanical properties of hemp/E-glass fabrics reinforced polyester hybrid composites. Vacuum bagging method was used for the preparation of six different kinds of hemp/glass fabrics reinforced polyester composite laminates as per layering sequences. The tensile, flexural, impact and water absorption tests of these hybrid composites were carried out experimentally according to ASTM standards. It reveals that an addition of E-glass fabrics with hemp fabrics can increase the mechanical properties of composites and decrease the water absorption of the hybrid composites.

  8. Thermochemical pretreatments for enhancing succinic acid production from industrial hemp (Cannabis sativa L.)

    DEFF Research Database (Denmark)

    Gunnarsson, Ingólfur Bragi; Kuglarz, Mariusz; Karakashev, Dimitar Borisov

    2015-01-01

    The aim of this study was to develop an efficient thermochemical method for treatment of industrial hemp biomass, in order to increase its bioconversion to succinic acid. Industrial hemp was subjected to various thermochemical pretreatments using 0-3% H2SO4, NaOH or H2O2 at 121-180°C prior...... to enzymatic hydrolysis. The influence of the different pretreatments on hydrolysis and succinic acid production by Actinobacillus succinogenes 130Z was investigated in batch mode, using anaerobic bottles and bioreactors. Enzymatic hydrolysis and fermentation of hemp material pretreated with 3% H2O2 resulted...... in the highest overall sugar yield (73.5%), maximum succinic acid titer (21.9gL-1), as well as the highest succinic acid yield (83%). Results obtained clearly demonstrated the impact of different pretreatments on the bioconversion efficiency of industrial hemp into succinic acid....

  9. Hemp farming development and socioeconomic position of Bačka: Example of Odžaci

    Directory of Open Access Journals (Sweden)

    Stojanović Vladimir

    2016-01-01

    Full Text Available Hemp is a very important agricultural crop for Bačka region. For centuries, hemp had been grown in this area and it had a crucial importance not only for the agriculture, but for the industry and trade of this region as well. From uncultivated, poorly inhabited and underdeveloped area in 18th century, Bačka made its way to a promising region in which agriculture and industry represent the backbone of the economic development. Significant number of colonial settlements from 18th century and colonization period during rule of Austro-Hungarian empress Maria Theresa recognized growing hemp as their main opportunities to prosper. Later on, in these settlements, the small manufactories for hemp processing were built which eventually had grown into larger factories for hemp fabric production. The town of Odžaci was one of these settlements. From a small colonial settlement, it became one of the important industrial centres in Bačka region.

  10. Kenaf-and hemp-reinforced natural fibre composites

    International Nuclear Information System (INIS)

    Sharifah Hanisah Aziz

    2003-01-01

    The main aim of this research is to combine hemp and kenaf fibres with thermosetting resin matrices to produce sustainable composites and to investigate their mechanical properties. The matirces used in this work are based on either unsaturated polyester resins or cashew nut shell liquid (CNSL). The latter can be polymerised to form a phenolic-based natural resin. Four types of differently formulated polyester resins provided by Scott Bader Ltd, a UK-based resin company, were used to assess the effect of resin formulation on the properties of natural fibre composites. CSNL resins were used because CNSL is a sustainable resource and these resins are compatible with natural fibres. Kenaf, which is extensively grown in the Far East including Malaysia, has been identified as a bast (stem) fibre with significant market potential. Hemp is a United Kingdom-grown bast fibre with strong potential as a natural fibre reinforcement. In order to improve matrix to fibre adhesion, the fibres were treated with 6 % NaOH solution before being made into composites. The composites were fabricated using unidirectional and randomly oriented fibres to assess the effect of fibre alignment on the properties of the composites. The effect of moulding pressure on the fibre volume fraction and mechanical properties was also investigated. Kenaf and hemp fibre composites were successfully hot-pressed with polyester and CNSL resin matrices. Kenaf-CNSL (treated long fibre) composites possess the highest flexural modulus (MOE) at 16.7 GPa and flexural strength (MOR) at 165.4 MPa indicating good matrix to fibre adhesion. Generally, the treated fibre composites gave higher MOE and MOR values compared to the untreated composites. However, the work of fracture values were generally higher for the untreated fibre composites. among the four types of polyester used, the molecular structure of polyester B, modified to make it more polar in nature, resulted in the best performance with treated long kenaf

  11. DETERMINATION OF CRYSTALLINITY INDEX OF CARBOHYDRATE COMPONENTS IN HEMP (CANNABIS SATIVA L. WOODY CORE BY MEANS OF FT-IR SPECTROSCOPY

    Directory of Open Access Journals (Sweden)

    Esat Gümüşkaya

    2005-04-01

    Full Text Available In this study; it was investigated chemical compositions of hemp woody core and changes in crystallinity index of its carbohydrate components by using FT-IR spectroscopy was investigated. It was determined that carbohyrate components ratio in hemp woody core were similar to that in hard wood, but lignin content in hemp woody core was higher than in hard wood. Crystallinity index of carbohydrate components in hemp woody core increased by removing amorphous components. It was designated that monoclinic structure in hemp woody core and its carbohydrate components was dominant, but triclinic ratio increased by treated chemical isolation of carbohydrate from hemp woody core.

  12. Thermochemical pretreatments for enhancing succinic acid production from industrial hemp (Cannabis sativa L.).

    Science.gov (United States)

    Gunnarsson, Ingólfur B; Kuglarz, Mariusz; Karakashev, Dimitar; Angelidaki, Irini

    2015-04-01

    The aim of this study was to develop an efficient thermochemical method for treatment of industrial hemp biomass, in order to increase its bioconversion to succinic acid. Industrial hemp was subjected to various thermochemical pretreatments using 0-3% H2SO4, NaOH or H2O2 at 121-180°C prior to enzymatic hydrolysis. The influence of the different pretreatments on hydrolysis and succinic acid production by Actinobacillus succinogenes 130Z was investigated in batch mode, using anaerobic bottles and bioreactors. Enzymatic hydrolysis and fermentation of hemp material pretreated with 3% H2O2 resulted in the highest overall sugar yield (73.5%), maximum succinic acid titer (21.9 g L(-1)), as well as the highest succinic acid yield (83%). Results obtained clearly demonstrated the impact of different pretreatments on the bioconversion efficiency of industrial hemp into succinic acid. Copyright © 2015. Published by Elsevier Ltd.

  13. Stalking: a neurobiological perspective.

    Science.gov (United States)

    Marazziti, Donatella; Falaschi, Valentina; Lombardi, Amedeo; Mungai, Francesco; Dell'Osso, Liliana

    2015-01-01

    Nowadays stalking is becoming a real social emergency, as it may often fuel severe aggressive behaviours. No exhaustive aetiological hypothesis is still available regarding this complex phenomenon. However, the detailed descriptions of some of its peculiar features allow to draw with cautions some general suggestions. Probably stalking may arise from the derangement of those neural networks subserving the so-called social brain and the pair bonding formation, in particular the processes of attachment/separation, attraction/romantic love/reward. In addition, it seems to be modulated by excessive functioning of the dopamine system coupled with decreased serotonin tone. It is believed that the investigation and deepening of its possible neurobiological substrates may be helpful in the prevention of the severe consequences of stalking.

  14. Hemp raw materials: The effect of cultivar, growth conditions and pretreatment on the chemical composition of the fibres

    DEFF Research Database (Denmark)

    Thomsen, A.B.; Rasmussen, S.K.; Bohn, V.

    2005-01-01

    Hemp raw materials were analyzed chemically to determine their content of cellulose, hemicellulose, lignin and ashes. Correction for ashes was only necessary in the first step of the chemical analysis: the Neutral Detergent Fibre step. The hemp fiberscontained 73-77% w/w cellulose, 7-9% w....../w hemicellulose and 4-6% w/w lignin, while the hemp shives contained 48% w/w cellulose, 21-25% w/w hemicellulose and 17-19% w/w lignin. Among the four investigated cultivars, Felina contained least lignin, whileFutura and Fasamo contained least cellulose. Hemp yarn had the same color as retted hemp fibers...... but was more cellulose rich. Steam explosion, wet oxidation and hydrothermal treatment were used for defibration of retted hemp fibers. These pretreatmentsremoved lignin and hemicellulose resulting in loss of dry matter of 15-73% w/w and in loss of cellulose of 0-69% w/w. Steam explosion treatment generally...

  15. Stalking: A Multidimensional Framework for Assessment and Safety Planning.

    Science.gov (United States)

    Logan, T K; Walker, Robert

    2015-09-03

    Despite the high prevalence of stalking and the risk of harm it poses to victims, arrest rates, prosecutions, and convictions for stalking continue to be low in the United States. The overall goal of this article is to introduce a multidimensional framework of stalking that adds to the current literature by (1) providing a conceptual framework consistent with legal elements of many stalking statutes to facilitate assessment, communication, documentation, and safety planning for stalking several victims; (2) introducing a more systematic way of assessing course of conduct and the context of fear in stalking situations in order to increase the understanding of cumulative fear for stalking victims; (3) emphasizing the aspects of stalking harm that go beyond violence and that show how harm from stalking accumulates over time including life sabotage; and (4) discussing 12 risk factors derived from the overall multidimensional framework that can be used to describe the big picture of stalking and to facilitate safety planning for victims. Implications for future research are discussed. © The Author(s) 2015.

  16. Hemp fibres: Enzymatic effect of microbial processing on fibre bundle structure

    DEFF Research Database (Denmark)

    Thygesen, Anders; Liu, Ming; Meyer, Anne S.

    2013-01-01

    The effects of microbial pretreatment on hemp fibres were evaluated after microbial retting using the white rot fungi Ceriporiopsis subvermispora and Phlebia radiata Cel 26 and water retting. Based on chemical composition, P. radiata Cel 26 showed the highest selectivity for pectin and lignin...... degradation and lowest cellulose loss (14%) resulting in the highest cellulose content (78.4%) for the treated hemp fibres. The pectin and lignin removal after treatment with P. radiata Cel 26 were of the order 82% and 50%, respectively. Aligned epoxy-matrix composites were made from hemp fibres defibrated...... with the microbial retting to evaluate the effects on their ultrastructure. SEM microscopy of the composites showed low porosity on the fibre surfaces after defibration with P. radiata Cel 26 and C. subvermispora indicating good epoxy polymer impregnation. In contrast, fibres treated by water retting and the raw...

  17. Characterization of Lignanamides from Hemp (Cannabis sativa L.) Seed and Their Antioxidant and Acetylcholinesterase Inhibitory Activities.

    Science.gov (United States)

    Yan, Xiaoli; Tang, Jiajing; dos Santos Passos, Carolina; Nurisso, Alessandra; Simões-Pires, Claudia Avello; Ji, Mei; Lou, Hongxiang; Fan, Peihong

    2015-12-16

    Hemp seed is known for its content of fatty acids, proteins, and fiber, which contribute to its nutritional value. Here we studied the secondary metabolites of hemp seed aiming at identifying bioactive compounds that could contribute to its health benefits. This investigation led to the isolation of 4 new lignanamides, cannabisin M (2), cannabisin N (5), cannabisin O (8), and 3,3'-demethyl-heliotropamide (10), together with 10 known lignanamides, among which 4 was identified for the first time from hemp seed. Structures were established on the basis of NMR, HR-MS, UV, and IR as well as by comparison with the literature data. Lignanamides 2, 7, and 9-14 showed good antioxidant activity, among which 7, 10, and 13 also inhibited acetylcholinesterase in vitro. The newly identified compounds in this study add to the diversity of hemp seed composition, and the bioassays implied that hemp seed, with lignanamides as nutrients, may be a good source of bioactive and protective compounds.

  18. Planting Date and Seeding Rate Effects on Sunn Hemp Biomass and Nitrogen Production for a Winter Cover Crop

    Directory of Open Access Journals (Sweden)

    Kipling S. Balkcom

    2011-01-01

    Full Text Available Sunn hemp (Crotalaria juncea L. is a tropical legume that produces plant biomass and nitrogen (N quickly. Our objectives were to assess the growth of a new sunn hemp cultivar breed to produce seed in a temperate climate and determine the residual N effect on a rye (Secale cereale L. cover crop in east-central Alabama from 2007 to 2009. Plant populations, plant height, stem diameter, biomass production, and N content were determined for two sunn hemp planting dates, following corn (Zea mays L. and wheat (Triticum aestivum L. harvest, across different seeding rates (17, 34, 50, and 67 kg/ha. Rye biomass was measured the following spring. Sunn hemp biomass production was inconsistent across planting dates, but did relate to growing degree accumulation. Nitrogen concentrations were inversely related to biomass production, and subsequent N contents corresponded to biomass levels. Neither planting date nor seeding rate affected rye biomass production, but rye biomass averaged over both planting dates following wheat/sunn hemp averaged 43% and 33% greater than rye following fallow. Rye biomass following corn/sunn hemp was equivalent to fallow plots. Early planting dates are recommended for sunn hemp with seeding rates between 17 and 34 kg/ha to maximize biomass and N production.

  19. Anti-inflammatory effect of methanol extracts of hemp leaf in IL-1β ...

    African Journals Online (AJOL)

    Purpose: To examine the effectiveness of some hemp (Canabis sativa) leaf extracts as an antiinflammatory agent on synovitis in vitro. Methods: Synovial fibroblast cell line SW982 was induced with 5 ng/mL of interleukin 1-beta (IL-1β) to trigger cellular inflammation. The cells were then treated with prepared extracts of hemp ...

  20. [Anaerobic co-digestion of corn stalk and vermicompost].

    Science.gov (United States)

    Chen, Guang-yin; Zheng, Zheng; Zou, Xing-xing; Fang, Cai-xia; Luo, Yan

    2010-02-01

    The characteristics of corn stalk digested alone at different total solid (TS) loading rates and co-digestion of various proportions of corn stalk and vermicompost were investigated by batch model at 35 degrees C +/- 1 degrees C. The organic loading rates (OLRs) studied were in the range of 1.2%-6.0% TS and increasing proportions of vermicompost from 20% to 80% TS. A maximum methane yield of corn stalk digested alone was 217.60 mL/g obtained at the TS loading rate of 4.8%. However, when the TS loading rate was 6.0%, the anaerobic system was acidified and the lowest pH value was 5.10 obtained on day 4 and the biogas productivity decreased. Furthermore, co-digestion of vermicompost and corn stalk in varying proportions were investigated at constant of 6.0% TS. Co-digestion with vermicompost improved the biodegradability of corn stalk and the methane yield was improved by 4.42%-58.61%, and led to higher pH values, higher volatile fatty acids (VFAs) concentration and lower alkalinity content compared with corn stalk digested alone. The maximum biogas yield and methane yield of 410.30 mL/g and 259. 35 mL/g were obtained for 40% vermicompost and 60% corn stalk respectively. Compared with corn stalk digested alone, co-digested with vermicompost didn' t affect methane content and the fermentation type, but promoted the destruction of crystalline of cellulose and the highest destruction rate was 29.36% for 40% vermicompost and 60% corn stalk. Therefore, adding vermicompost was beneficial for the decomposition and increasing the biotransformation rate of corn stalk.

  1. Hemp-Lime Performance in Danish Climatic Context. Thermal Conductivity as a Function of Moisture Content

    DEFF Research Database (Denmark)

    Antonov, Yovko Ivanov; Jensen, Rasmus Lund; Pomianowski, Michal Zbigniew

    2016-01-01

    concrete is a bio-based building material composed of the woody core of industrial hemp and lime based binder. It is a non-load-bearing material, which can be used as floor and around structural frames for walls and roof. The material is characterized by relatively low environmental impact, moderate...... thermal properties and, high air and moisture permeability. The properties vary with binder composition, mixing and casting techniques, as well as intended application. This research presents preliminary heat and moisture building simulations of single family house made out of hemp-lime composite....... To evaluate the performance of hemp-lime, it is compared to models with common external walls, upon defined parameters. The article also determines the variation of thermal conductivity for hemp-lime commercial plaster and wall mix, as a function of moisture content. The most promising binder composition...

  2. Bioethanol production from dried sweet sorghum stalk

    Energy Technology Data Exchange (ETDEWEB)

    Almodares, A.; Etemadifar, Z.; Ghoreishi, F.; Yosefi, F. [Biology Dept. Univ. of Isfahan, Isfahan (Iran, Islamic Republic of)], e-mail: aalmodares@yahoo.com

    2012-11-01

    Bioethanol as a renewable transportation fuel has a great potential for energy and clean environment. Among crops sweet sorghum is one of the best feedstock for ethanol production under hot and dry climatic conditions. Because it has higher tolerance to salt and drought comparing to sugarcane and corn that are currently used for bio-fuel production in the world. Generally mills are used to extract the juice from sweet sorghum stalks. Three roller mills extract around nearly 50 percent of the juice and more mills is needed to extract higher percentage of the juice. More over under cold weather the stalks become dry and juice is not extracted from the stalk, therefore reduce harvesting period. In this study stalks were harvested, leaves were stripped from the stalks and the stalks were chopped to nearly 4 mm length and sun dried. The dry stalks were grounded to 60 mesh powder by a mill. Fermentation medium consists of 15-35% (w/w) sweet sorghum powder, micronutrients and active yeast inoculum from 0.5-1% (w/w) by submerge fermentation method. The fermentation time and temperature were 48-72 hours and 30 deg, respectively. The results showed the highest amount of ethanol (14.5 % w/w sorghum) was produced with 10% sweet sorghum powder and 1% of yeast inoculum, three day fermentation at 30 deg.

  3. Characterization of chemically and enzymatically treated hemp fibres using atomic force microscopy and spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    George, Michael; Mussone, Paolo G. [Biorefining Conversions and Fermentations Laboratory, Department of Agricultural, Food and Nutritional Science, University of Alberta, Edmonton, AB, Canada T6E 2P5 (Canada); Abboud, Zeinab [Biorefining Conversions and Fermentations Laboratory, Department of Agricultural, Food and Nutritional Science, University of Alberta, Edmonton, AB, Canada T6E 2P5 (Canada); Department of Physics, University of Guelph, Guelph, ON, Canada N1G 2W1 (Canada); Bressler, David C., E-mail: david.bressler@ualberta.ca [Biorefining Conversions and Fermentations Laboratory, Department of Agricultural, Food and Nutritional Science, University of Alberta, Edmonton, AB, Canada T6E 2P5 (Canada)

    2014-09-30

    The mechanical and moisture resistance properties of natural fibre reinforced composites are dependent on the adhesion between the matrix of choice and the fibre. The main goal of this study was to investigate the effect of NaOH swelling of hemp fibres prior to enzymatic treatment and a novel chemical sulfonic acid method on the physical properties of hemp fibres. The colloidal properties of treated hemp fibres were studied exclusively using an atomic force microscope. AFM imaging in tapping mode revealed that each treatment rendered the surface topography of the hemp fibres clean and exposed the individual fibre bundles. Hemp fibres treated with laccase had no effect on the surface adhesion forces measured. Interestingly, mercerization prior to xylanase + cellulase and laccase treatments resulted in greater enzyme access evident in the increased adhesion force measurements. Hemp fibres treated with sulfonic acid showed an increase in surface de-fibrillation and smoothness. A decrease in adhesion forces for 4-aminotoulene-3-sulfonic acid (AT3S) treated fibres suggested a reduction in surface polarity. This work demonstrated that AFM can be used as a tool to estimate the surface forces and roughness for modified fibres and that enzymatic coupled with chemical methods can be used to improve the surface properties of natural fibres for composite applications. Further, this work is one of the first that offers some insight into the effect of mercerization prior to enzymes and the effect on the surface topography. AFM will be used to selectively screen treated fibres for composite applications based on the adhesion forces associated with the colloidal interface between the AFM tip and the fibre surfaces.

  4. Fatty acid composition of hemp seed oils from different locations in Turkey

    Energy Technology Data Exchange (ETDEWEB)

    Kiralan, M.; Gul, V.; Metin Kara, S.

    2010-07-01

    Recent interest in hemp seed as a source of food has largely focused on its oil content and fatty acid profile. The oil content and fatty acid composition (15 fatty acids) of twenty one different hemp seed samples of domestic origin from north-western Turkey were monitored. The samples were obtained from seed wholesalers and local spice shops and are of unknown genetic origin. The oil content of the hemp seeds ranged between 29.6 to 36.5%. Out of the 15 detected fatty acids, the omega-6 linoleic acid (18:2n-6) was predominant and fluctuated from 55.4 to 56.9%, while the omega-3 a-linolenic (18:3n-3) acid ranged from 16.5 to 20.4% and the omega-9 oleic acid (18:1n-9) ranged from 11.4 to 15.9%. Of the minor fatty acids, the highest concentrations were found for {gamma}-linolenic acid (18:3n-6), range 0.6-1.1%, followed by stearidonic acid (18:4n-3), range 0.3-0.5%. These results show that hemp seed grown in north-western Turkey provides a well balanced and rich source of dietary omega-6 and -3 essential fatty acids and appears to be a potentially valuable source of food. (Author) 31 refs.

  5. [Nurses' experiences of stalking: a narrative review].

    Science.gov (United States)

    Comparcini, Dania; Simonetti, Valentina; Lupo, Roberto; Cicolini, Giancarlo

    2015-01-01

    This narrative review aimed to synthetize the results of the main studies analysing nurses' experience of stalking in different clinical settings. We searched the electronic databases MEDLINE (through PubMed), CINAHL (through EBSCOhost) and the search engine "Google Scholar". Searches were limited to articles published in English and Italian, and published between 1999 and 2013. Stalking refers to a behavioural pattern characterized by persistent unwanted communications and contacts imposed to another person, which, consequently suffer from distress, fear, and anxiety. Several studies explored the risk of stalking in healthcare system, especially in doctors and psychiatrists. Some authors analysed nurses' experience of stalking with particular attention to mental health professionals as a group category with an increased risk of stalking by patients. Results of some studies carried out in different clinical settings (medical and surgical areas, and other healthcare settings) also revealed, even if in a minority, the presence of this phenomenon, showing the presence of staking's behaviours by patients and healthcare colleagues too. However, more researches with large sample size are needed to better understand the phenomenon of stalking in nurses working in different clinical areas.

  6. Effects of Environmental Surface Modification Methods on Physical Properties of Hemp Fibers

    Directory of Open Access Journals (Sweden)

    Nigar MERDAN

    2017-11-01

    Full Text Available In this study, hemp fibers have been pre-treated with laccase enzyme in different concentrations (1%, 2% and 3% w/v for different durations using conventional, ultrasonic energy and microwave energy methods. Weight loss (%, tensile strength, elongation (%, whiteness (%, and surface topography (SEM properties of pre-treated hemp fibers were investigated. After processing with laccase enzyme, the energy consumptions of these three methods were compared. Best results have been obtained in 20 minutes with the conventional method, 5 minutes with the ultrasonic energy method, and 1 minute with the microwave energy method. With laccase enzyme, microwave treated hemp fibers were improved after 3 minutes treatment. SEM results have also proved the improved physical properties and color changes due to the rough surface structure. DOI: http://dx.doi.org/10.5755/j01.ms.23.4.17469

  7. Stalking Victimization in LGBTQ Adults: A Brief Report.

    Science.gov (United States)

    Langenderfer-Magruder, Lisa; Walls, N Eugene; Whitfield, Darren L; Kattari, Shanna K; Ramos, Daniel

    2017-03-01

    Stalking is often considered to be a form of interpersonal violence; yet, despite an increase in lesbian, gay, bisexual, transgender, and queer (LGBTQ)-specific research on other forms of interpersonal violence, such as intimate partner violence and sexual assault, there is a relative lack of literature on stalking victimization of LGBTQ individuals, particularly as it relates to gender identity. This is problematic given the results of numerous studies indicating LGBTQ individuals, and transgender individuals in particular, experience victimization in various forms and contexts at alarming rates. In the current study, we examined secondary data to determine the prevalence of lifetime stalking victimization and subsequent police reporting in a large community-based sample of LGBTQ individuals living in Colorado ( N = 1,116). In addition, using chi-square analyses, we examined independence of stalking experiences and police reporting by both gender identity ( transgender, cisgender male, cisgender female) and sexual orientation ( gay, lesbian, bisexual, heterosexual, queer, other). Approximately 15% of the total sample reported ever experiencing stalking; yet, only about one quarter of those who were stalked reported it to police. Although no statistically significant differences emerged by gender identity or sexual orientation, transgender, bisexual, and queer participants had the highest prevalence of lifetime stalking victimization. Moreover, these groups reported the lowest prevalence of reporting their victimization to the police. We provide suggestions to improve the development of research on this topic including a need for an inclusive definition of stalking and studies using larger, representative samples to better discern potential significant differences in stalking experiences of LGBTQ persons.

  8. Application of bokashi and sunn hemp (Crotalaria juncea L. to improve inorganic fertilizer efficiency on maize (Zea mays L.

    Directory of Open Access Journals (Sweden)

    A.I. Yuliana

    2015-10-01

    Full Text Available A field experiment was conducted lo learn about the effect of Bokashi and Sunn hemp (Crotalaria juncea L. on maize production and inorganic fertilizer use efficiency on maize. The experiment was conducted in Jatikerto, Malang; at the altitude of 303 m above sea level, in Alfisol soil type, the average daily temperature ranges 21-33oC, from June to October 2013. The experiment was conducted as factorial, designed in a randomized block design (RBD. The first factor was dose of inorganic fertilizer (100% ; 75% and 50% of recommendation dose. The second factor was the organic fertilizer (Without organic fertilizer20 t Bokashi/ ha, 20 t Sunn hemp/ha, 10 t Bokashi/ha + 10 t Sunn hemp/ha. The results showed that application of 20 t Bokashi/ha, 20 t Sunn hemp/ha, and combination of 10 t Bokashi/ha + 10 t Sunn hemp/ha, along with the application of inorganic fertilizer by dose of 100% increased the yields of maize for about 41.8%; 47.6% and 54.7% (10.73 t/ha; 11.17 t/ha, and 11.71 t/ha, respectively. The yield and nutrient use efficiency in the treatment dose of 100% inorganic fertilizer did not have any significant difference from the application of 20 t Bokashi /ha, 20 t Sunn hemp/ha, and 10 t Bokashi/ha + 10 t Sunn hemp/ha along with doses of inorganic fertilization 75% and 50%. Therefore, the organic fertilizer of 20 t Bokashi/ ha, 20 t Sunn hemp/ha, and combination of 10 t Bokashi/ha + 10 t Sunn hemp/ha could reduce the need of inorganic fertilizer for about 50%.

  9. The consequences of coping with stalking

    DEFF Research Database (Denmark)

    Johansen, Katrine Bindesbøl Holm; Tjørnhøj-Thomsen, Tine

    2016-01-01

    OBJECTIVES: The purpose of this article is to explore: (1) how victims of stalking experience the phenomenon in their daily life, (2) how the nature of stalking informs the victim's internal coping strategies, and (3) how the victims' internal coping strategies negatively affect their daily life...... and well-being. METHODS: Qualitative semi-structured interviews were conducted with 25 victims of stalking. Thematic content analysis was employed, and themes were primarily identified inductively and broad into dialogue with concepts, such as Foucault's panopticism. RESULTS: The results of the study...

  10. Targeted pre-treatment of hemp bast fibres for optimal performance in biocomposite materials: A review

    DEFF Research Database (Denmark)

    Liu, Ming; Thygesen, Anders; Summerscales, John

    2017-01-01

    . In order to achieve strong NFCs, well separated and cellulose-rich fibres are required. Hemp is taking a center stage in this regard as a source of suitable natural plant cellulose fibres because natural hemp bast fibres are long and inherently possess high strength. Classical field and water retting...... methods have been used for centuries for removal of non-cellulosic components from fibrous plant stems including from hemp, but carries a risk of reducing the mechanical properties of the fibres via damaging the cellulose. For NFCs new targeted fibre pre-treatment methods are needed to selectively...... and effectively remove non-cellulosic components from the plant fibres to produce cellulose rich fibres without introducing any damage to the fibres. A key feature for successful use of natural fibres such as hemp fibres in composite materials is optimal interfacial contact between the fibres and the hydrophobic...

  11. Engineering Properties of Treated Natural Hemp Fiber-Reinforced Concrete

    Directory of Open Access Journals (Sweden)

    Xiangming Zhou

    2017-06-01

    Full Text Available In recent years, the construction industry has seen a significant rise in the use of natural fibers, for producing building materials. Research has shown that treated hemp fiber-reinforced concrete (THFRC can provide a low-cost building material for residential and low-rise buildings, while achieving sustainable construction and meeting future environmental targets. This study involved enhancing the mechanical properties of hemp fiber-reinforced concrete through the Ca(OH2 solution pretreatment of fibers. Both untreated (UHFRC and treated (THFRC hemp fiber-reinforced concrete were tested containing 15-mm length fiber, at a volume fraction of 1%. From the mechanical strength tests, it was observed that the 28-day tensile and compressive strength of THFRC was 16.9 and 10% higher, respectively, than UHFRC. Based on the critical stress intensity factor (KICs and critical strain energy release rate (GICs, the fracture toughness of THFRC at 28 days was also found to be 7–13% higher than UHFRC. Additionally, based on the determined brittleness number (Q and modulus of elasticity, the THFRC was found to be 11% less brittle and 10.8% more ductile. Furthermore, qualitative analysis supported many of the mechanical strength findings through favorable surface roughness observed on treated fibers and resistance to fiber pull-out.

  12. Health Care Professionals as Victims of Stalking: Characteristics of the Stalking Campaign, Consequences, and Motivation in Italy.

    Science.gov (United States)

    Acquadro Maran, Daniela; Varetto, Antonella; Zedda, Massimo; Franscini, Monica

    2015-07-05

    Stalking is a phenomenon characterized by a set of repetitive behaviors, intrusive surveillance, control, communication, and search of contact with a victim who is afraid and/or worried and/or annoyed by such unwanted attention. Literature analysis shows that Health Care Professionals (HCPs) are at greater risk of being stalked than the general population. As described by Mullen, Pathé, Purcell, and Stuart, stalkers may have different motives: relational rejection, an infatuation, an inability to express their own emotions and recognize those of others, or a desire for revenge. The aim of this study was to explore stalkers' motivation as perceived by their victims, characteristics of stalking campaigns, and consequences. A copy of the Italian modified version of The Network for Surviving Stalking (NSS) Questionnaire on Stalking, the Beck Depression Inventory (BDI) and the State Trait Inventory (STAI) Y1-Y2 scales were distributed in six Italian state hospitals. Participants included 1,842 HCPs, 256 (13.9%) of which had been victims. The majority of victims reported that stalkers were Rejected (96, 37.5%), Intimacy seekers (41, 16%), Incompetent suitors (60, 23.4%), and/or Resentful (43, 16.8%; χ 2 = 163.3, p = .001). Stalking campaigns were characterized by several behaviors, principally contact (by telephone calls, text message) and following. The stalking campaign caused in victims both physical and emotional consequences, the most frequent being weight changes, sleep disorders, weakness, apprehension, anger, and fear. The most used coping strategies were moving away and moving toward, the less used was moving inward. Intervention programs and preventive measures (both individual and organizational) for HCP victims and those who could be considered at risk are also discussed. © The Author(s) 2015.

  13. Some thoughts on the neurobiology of stalking.

    Science.gov (United States)

    Meloy, J Reid; Fisher, Helen

    2005-11-01

    The authors examine the crime of stalking, including the cognitive traits, emotional reactions, attachment pathology, violence patterns and sex differences of samples of stalking offenders. They focus on two common types of stalkers: 1) those who sustain pursuit of a former sexual intimate who has rejected them; and 2) those who pursue a stranger or acquaintance who has failed to return the stalker's romantic overtures. The authors discuss data from neuroimaging (fMRI) studies of romantic love which suggest that these forms of stalking may be associated with heightened activity of subcortical dopaminergic pathways of the "Reward System" of the brain, perhaps in combination with low activity of central serotonin. The authors propose that this set of neural correlates may contribute to the stalker's focused attention, increased energy, following behaviors, obsessive thinking about and impulsivity directed toward the victim. To further explore the neural systems associated with stalking behavior, they also discuss several biopsychological phenomena associated with romantic rejection, including the "protest response," "frustration attraction," "abandonment rage" and "mate guarding." They illustrate the parallels between stalking and addiction. They conclude that stalking may be associated with a specific set of biological components and they offer suggestions for further research into this pathological emotional/motivational state.

  14. Stalking Behavior and the Cycle of Domestic Violence.

    Science.gov (United States)

    Coleman, Frances L.

    1997-01-01

    Refines the behavioral definition of stalking, investigates the role stalking plays in domestic violence, and develops demographic profiles of stalkers and their victims. Results based on information taken from 141 college women show that subjects who reported significantly more abuse during relationships were more likely to be stalked by former…

  15. The potential of hemp (Cannabis sativa L.) for sustainable fibre production: a crop physiological appraisal.

    NARCIS (Netherlands)

    Werf, van der H.M.G.; Mathijssen, E.W.J.M.; Haverkort, A.J.

    1996-01-01

    Hemp (Cannabis sativa L.) fibre can be used as a raw material for paper and textile production. A comprehensive research programme in the Netherlands has concluded that fibre hemp is a potentially profitable crop, having the right profile to fit into sustainable farming systems. This paper presents

  16. Effect of sunn hemp (Crotalaria juncea L.) cutting date and planting density on weed suppression in Georgia, USA.

    Science.gov (United States)

    Morris, J Bradley; Chase, Carlene; Treadwell, Danielle; Koenig, Rosie; Cho, Alyssa; Morales-Payan, Jose Pable; Murphy, Tim; Antonious, George F

    2015-01-01

    A field study was conducted in 2008 and 2009 at the USDA, ARS, Plant Genetic Resources Conservation Unit in Griffin, GA, to investigate weed suppression by sunn hemp (Crotalaria juncea L). The objectives were to (1) evaluate the effects of apical meristem removal (AMR) at three dates [5, 6, and 7 wks after planting (WAP) on May 14, 2008 and May 21, 2009] and (2) assess the impact of seeding rates (11, 28, and 45 kg ha(-1)) on weed biomass reduction. Weed species were identified at 4, 8, and 12 wks after sunn hemp planting. Sunn hemp cutting date had no significant effect on weed suppression in 2008 but significant differences for grass weeds at 4, 8, and 12 WAP and for yellow nutsedge at 8 and 12 WAP did occur when compared to the control in 2009. In comparison to the sunn hemp-free control plot in 2009, all three seeding rates had reduced grass weed dry weights at 4, 8, and 12 WAP. The total mass of yellow nutsedge when grown with sunn hemp was reduced compared to the total mass of yellow nutsedge grown in the weedy check for all seeding rates at 8 and 12 WAP. Lower grass weed biomass was observed by 12 WAP for cutting dates and seeding rates during 2008 and 2009. Sunn hemp cutting date and seeding rate reduced branch numbers in both years. The reduction in sunn hemp seeding rates revealed a decrease in weed populations.

  17. The Small Protein HemP Is a Transcriptional Activator for the Hemin Uptake Operon in Burkholderia multivorans ATCC 17616.

    Science.gov (United States)

    Sato, Takuya; Nonoyama, Shouta; Kimura, Akane; Nagata, Yuji; Ohtsubo, Yoshiyuki; Tsuda, Masataka

    2017-08-15

    Iron and heme play very important roles in various metabolic functions in bacteria, and their intracellular homeostasis is maintained because high concentrations of free forms of these molecules greatly facilitate the Fenton reaction-mediated production of large amounts of reactive oxygen species that severely damage various biomolecules. The ferric uptake regulator (Fur) from Burkholderia multivorans ATCC 17616 is an iron-responsive global transcriptional regulator, and its fur deletant exhibits pleiotropic phenotypes. In this study, we found that the phenotypes of the fur deletant were suppressed by an additional mutation in hemP The transcription of hemP was negatively regulated by Fur under iron-replete conditions and was constitutive in the fur deletant. Growth of a hemP deletant was severely impaired in a medium containing hemin as the sole iron source, demonstrating the important role of HemP in hemin utilization. HemP was required as a transcriptional activator that specifically binds the promoter-containing region upstream of a Fur-repressive hmuRSTUV operon, which encodes the proteins for hemin uptake. A hmuR deletant was still able to grow using hemin as the sole iron source, albeit at a rate clearly lower than that of the wild-type strain. These results strongly suggested (i) the involvement of HmuR in hemin uptake and (ii) the presence in ATCC 17616 of at least part of other unknown hemin uptake systems whose expression depends on the HemP function. Our in vitro analysis also indicated high-affinity binding of HemP to hemin, and such a property might modulate transcriptional activation of the hmu operon. IMPORTANCE Although the hmuRSTUV genes for the utilization of hemin as a sole iron source have been identified in a few Burkholderia strains, the regulatory expression of these genes has remained unknown. Our analysis in this study using B. multivorans ATCC 17616 showed that its HemP protein is required for expression of the hmuRSTUV operon, and the

  18. Integrated production of cellulosic bioethanol and succinic acid from industrial hemp in a biorefinery concept

    DEFF Research Database (Denmark)

    Kuglarz, Mariusz; Alvarado-Morales, Merlin; Karakashev, Dimitar Borisov

    2016-01-01

    The aim of this study was to develop integrated biofuel (cellulosic bioethanol) and biochemical (succinic acid) production from industrial hemp (Cannabis sativa L.) in a biorefinery concept. Two types of pretreatments were studied (dilute-acid and alkaline oxidative method). High cellulose recovery...... productivity. With respect to succinic acid production, the highest productivity was obtained after liquid fraction fermentation originated from steam treatment with 1.5% of acid. The mass balance calculations clearly showed that 149 kg of EtOH and 115 kg of succinic acid can be obtained per 1 ton of dry hemp....... Results obtained in this study clearly document the potential of industrial hemp for a biorefinery....

  19. The effects of growth conditions and of processing into yarn on dislocations in hemp fibres

    DEFF Research Database (Denmark)

    Thygesen, Lisbeth Garbrecht

    2011-01-01

    at harvest in hemp fibres from plants grown in a green house under three different regimes (wind free, windy and dry) with the percentage found in commercial hemp yarn. As expected a higher percentage of the cell wall consisted of dislocations in the processed fibres, but the increase was only significant...

  20. Investigation of mechanical properties of hemp/glass fiber reinforced nano clay hybrid composites

    Science.gov (United States)

    Unki, Hanamantappa Ningappa; Shivanand, H. K.; Vidyasagar, H. N.

    2018-04-01

    Over the last twenty to thirty years composite materials have been used in engineering field. Composite materials possess high strength, high strength to weight ratio due to these facts composite materials are becoming popular among researchers and scientists. The major proportion of engineering materials consists of composite materials. Composite materials are used in vast applications ranging from day-to-day household articles to highly sophisticated applications. In this paper an attempt is made to prepare three different composite materials using e-glass and Hemp. In this present investigation hybrid composite of Hemp, Glass fiber and Nano clay will be prepared by Hand-layup technique. The glass fiber used in this present investigation is E-glass fiber bi-directional: 90˚ orientation. The composite samples will be made in the form of a Laminates. The wt% of nanoclay added in the preparation of sample is 20 gm constant. The fabricated composite Laminate will be cut into corresponding profiles as per ASTM standards for Mechanical Testing. The effect of addition of Nano clay and variation of Hemp/glass fibers will be studied. In the present work, a new Hybrid composite is developed in which Hemp, E glass fibers is reinforced with epoxy resin and with Nano clay.

  1. Microwave-Assisted Extraction of Cannabinoids in Hemp Nut Using Response Surface Methodology: Optimization and Comparative Study

    Directory of Open Access Journals (Sweden)

    Chih-Wei Chang

    2017-11-01

    Full Text Available Hemp nut is commonly incorporated into several food preparations; however, most countries set regulations for hemp products according to their cannabinoid content. In this study, we have developed an efficient microwave-assisted extraction (MAE method for cannabinoids (i.e., Δ9-tetrahydrocannabinol, cannabidiol, and cannabinol in hemp nut. Optimization of the MAE procedure was conducted through single factor experiments and response surface methodology (RSM. A comparative study was also conducted to determine the differences in the extraction yields and morphology of hemp nut between MAE and reference extraction methods, namely heat reflux extraction (HRE, Soxhlet extraction (SE, supercritical fluid extraction (SFE, and ultrasound-assisted extraction (UAE. Among the independent variables in RSM, the temperature was the most significant parameter. The optimal conditions of MAE were as follows: extraction solvent of methanol, microwave power of 375 W, temperature of 109 °C, and extraction time of 30 min. Compared with reference extraction methods, MAE achieved the highest extraction yields of total cannabinoids in hemp nut (6.09 μg/g for MAE; 4.15 μg/g for HRE; 5.81 μg/g for SE; 3.61 μg/g for SFE; 3.73 μg/g for UAE with the least solvent consumption and shortest time. Morphological observations showed that substantial cell rupturing occurred in the microstructure of hemp nut after MAE, indicating enhanced dissolution of the target compounds during the extraction process. The MAE method is thus a rapid, economic, and environmentally friendly extraction method that is both effective and practical for industrial applications.

  2. Quantification of dislocations in hemp fibers using acid hydrolysis and fiber segment length distributions

    DEFF Research Database (Denmark)

    Thygesen, Lisbeth Garbrecht

    2008-01-01

    Natural fibers such as flax or hemp may be used in composite materials. However, their use for this purpose is hampered by the large natural variation in tensile strength and other quality parameters. The first step in managing these variations is to develop methods for fast and reliable determin......Natural fibers such as flax or hemp may be used in composite materials. However, their use for this purpose is hampered by the large natural variation in tensile strength and other quality parameters. The first step in managing these variations is to develop methods for fast and reliable...... determination of relevant parameters. One quality parameter of the fibers is the amount of structural distortions known as dislocations or kink bands. Here, a method developed for the quantification of dislocations in pulp fibers was adapted and tested successfully for hemp yarn segments. The method is based...... was correct, and furthermore results showed that fibers broke more often in large dislocations than in small ones. However, it was also found that the hemp fiber segments did not break in all dislocations, and strict standardization of the procedure for acid hydrolysis is therefore necessary if results from...

  3. Characterization of Sunn hemp begomovirus and its geographical ...

    African Journals Online (AJOL)

    Thus, it is concluded that the recombinant CP genes related to begomoviruses are evolved from the Indian isolates, causing broad host specificity and molecular diversity among the related begomoviruses across the geographical limits of Southeast Asia. Keywords: Begomovirus, sunn hemp, coat protein, recombination, ...

  4. Sequenced anaerobic - aerobic treatment of hemp pulping wastewaters

    NARCIS (Netherlands)

    Kortekaas, S.

    1998-01-01

    Biological treatment is an indispensable instrument for water management of non-wood pulp mills, either as internal measure to enable progressive closure of water cycles, or as end of pipe treatment. In this thesis, the sequenced anaerobic-aerobic treatment of hemp ( Cannabis

  5. [Stalking: From "romantic pursuit" to sexual predation].

    Science.gov (United States)

    Cailleau, Virginie; Harika-Germaneau, Ghina; Delbreil, Alexia; Jaafari, Nematollah

    2018-06-01

    Deriving from the English verb "to stalk", stalking denotes an unwelcome, repetitive, and intrusive harassing and/or threatening behavior directed toward a specific individual, and can result in physical and/or sexual offending - even leading to homicide. French harassment legislation has evolved over the years, and the last law closest to the international anti-stalking laws had been promulgated in 2014. According to a review, up to 16% of women and 7% of men are stalked in their life, and 80% of the stalkers are known to their victims. Stalkers are a heterogeneous population, either seeking an intimate relationship with someone the stalker knows or with a celebrity, or being revenge-motivated, or tracking their victims with the aim of offending them. Stalkers threat their victims in about half of the cases, and physically offend them in a third of the cases, violence being more often directed against ex-intimates. Sexual offending would be the consequence of harassment behavior for some stalkers, and would be the initial aim of the stalking for others. Copyright © 2018 Elsevier Masson SAS. All rights reserved.

  6. Ethanol production from industrial hemp: effect of combined dilute acid/steam pretreatment and economic aspects

    DEFF Research Database (Denmark)

    Gunnarsson, Ingólfur Bragi; Svensson, Sven-Erik; Prade, Thomas

    2014-01-01

    In the present study, combined steam (140-180 °C) and dilute-acid pre-hydrolysis (0.0-2.0%) were applied to industrial hemp (Cannabis sativa L.), as pretreatment for lignocellulosic bioethanol production. The influence of the pretreatment conditions and cultivation type on the hydrolysis and etha......In the present study, combined steam (140-180 °C) and dilute-acid pre-hydrolysis (0.0-2.0%) were applied to industrial hemp (Cannabis sativa L.), as pretreatment for lignocellulosic bioethanol production. The influence of the pretreatment conditions and cultivation type on the hydrolysis...... pretreated at the optimal conditions showed positive economic results. The type of hemp cultivation (organic or conventional) did not influence significantly the effectiveness of the pretreatment and subsequent enzymatic hydrolysis and ethanol fermentation....

  7. Influence of yarn folding on UV protection properties of hemp knitted fabrics

    Directory of Open Access Journals (Sweden)

    Kocić Ana A.

    2016-01-01

    Full Text Available In the last years the media have highlighted the damage of the ozone layer and the resulting increase of ultraviolet radiation (UVR reaching the earth’s surface. Prolonged and repeated, both occupational and recreational, sun exposure of the population causes some detrimental effects. Clothing is considered to be one of the most important tools for UV protection. It is generally accepted that synthetic fibres provide a high UV protection capability of textiles, while cellulose fibres (cotton, linen, hemp, viscose have a low UV absorption capacity. However, natural pigments, pectin and waxes in natural cellulose fibers, and lignin in hemp fibers, act as UV absorbers having a favorable effect on UPF of grey-state fabrics. Bearing in mind the trend of reintroduction of hemp fibers as a source of eco-friendly textiles, there is a serious lack of study about the potential of hemp materials in terms of UV protection. Folded yarn is a complex yarn composed of two or more component yarns arranged parallel and twisted together to make a “new quality” yarn. Folding of yarns is an operation undertaken in order to modify single-yarn properties to an appreciable degree. There are very few investigations concerning the relationship between the yarn properties and UV protection effectiveness of the fabric made there from. In addition, there is no any result in the scientific literature about the influence of yarn folding on UV protection properties of textile materials. Having this in mind, for our research the idea was to evaluate the effect of yarn folding in this regard. The plain knitted fabrics composed of single or two-folded hemp yarn were compared in terms of UV protection properties. The Ultraviolet Protection Factor (UPF, as the quantitative measurement of the material effectiveness to protect the human skin against UVR, was determined for the textile materials by in vitro test method according to the European standard EN 13758. The knitted

  8. Chopped hemp: Logistics, compaction and financial viability; Logistik, komprimering och ekonomi angaaende hackad hampa

    Energy Technology Data Exchange (ETDEWEB)

    Soederstroem, Yvonne

    2010-05-15

    In this project compaction and logistics experiments were conducted using chopped hemp. The aim was to reduce the hemp to 250 kg/m3, as well as to identify the best possible logistical system for compaction and subsequent transportation to the end-user in terms of cost and environmental impact. The project primarily focused on landowners and power companies. Other stakeholders are industries, universities and other ongoing projects in related fields. These studies have shown that it is possible to compact chopped hemp from a density of 60 kg dm/m3 (0.30 MWh/m3) when harvesting directly into the container, to a density of 202 kg dm/m3 (1.01 MWh/m3) using the baler. The original compaction target was a volumetric weight of 250 kg/m3. It was determined that straw and hemp react similarly to compaction. This project has demonstrated that the transport rig system has the best potential for large-scale use as compared with the alternate systems used. According to our calculations, the transport rig was the most cost-effective system measured in kronor per energy content. In addition, this system is also flexible. From an environmental standpoint, however, the energy balance showed that the container system was slightly superior

  9. Studying secondary growth and bast fiber development: the hemp hypocotyl peeks behind the wall

    Directory of Open Access Journals (Sweden)

    Marc Behr

    2016-11-01

    Full Text Available Cannabis sativa L. is an annual herbaceous crop grown for the production of long extraxylary fibers, the bast fibers, rich in cellulose and used both in the textile and biocomposite sectors. Despite being herbaceous, hemp undergoes secondary growth and this is well exemplified by the hypocotyl. The hypocotyl was already shown to be a suitable model to study secondary growth in other herbaceous species, namely Arabidopsis thaliana and it shows an important practical advantage, i.e. elongation and radial thickening are temporally separated. This study focuses on the mechanisms marking the transition from primary to secondary growth in the hemp hypocotyl by analysing the suite of events accompanying vascular tissue and bast fiber development. Transcriptomics, imaging and quantification of phytohormones were carried out on four representative developmental stages (i.e. 6-9-15-20 days after sowing to provide a comprehensive overview of the events associated with primary and secondary growth in hemp. This multidisciplinary approach provides cell wall-related snapshots of the growing hemp hypocotyl and identifies marker genes associated with the young (expansins, β-galactosidases and transcription factors involved in light-related processes and the older hypocotyl (secondary cell wall biosynthetic genes and transcription factors.

  10. Evaluation of Properties of Unidirectional Hemp/Polypropylene Composites: Influence of Fiber Content and Fiber/Matrix Interface Variables

    DEFF Research Database (Denmark)

    Plackett, David; Løgstrup Andersen, Tom; Lilholt, Hans

    2002-01-01

    Flament-wound textile hemp yarn was used in combination with unmodified or maleated polypropylene (PP) films to produce plates of unidirectional composites.......Flament-wound textile hemp yarn was used in combination with unmodified or maleated polypropylene (PP) films to produce plates of unidirectional composites....

  11. The prevalence of stalking in the Netherlands

    NARCIS (Netherlands)

    van der Aa, S.; Kunst, M.J.J.

    2009-01-01

    Over eight years after the enactment of the Dutch anti-stalking provisions there are still no figures detailing the prevalence of stalking in The Netherlands. This article aims to estimate the lifetime and annual prevalence of this form of victimization within the Dutch population. Questionnaires

  12. First Trials Of Hemp Cultivation For Fiber Applications In The East Of France Irrigation And Fertilization Analysis

    Directory of Open Access Journals (Sweden)

    Lotfi Harrabi

    2017-10-01

    Full Text Available This paper presents results from the first hemp experiments in Aspach-le-bas France carried out during summer 2014. Field trials were performed testing the variety Futura 75 at a seed rate of 50 kgha. Two rain densities have been used to analyse the effect of irrigation on its growth. Seven different configurations have been also studied in this work in order to figure out the best one for the hemp cultivation in this region. The composition of hemp biomass in terms of cellulose hemicellulose and lignine has also been analysed for each configuration.

  13. Mediators and Moderators of the Association Between Stalking Victimization and Psychological Distress.

    Science.gov (United States)

    Fais, Connor R; Lutz-Zois, Catherine J; Goodnight, Jackson A

    2017-03-01

    The current study aims to understand mediators and moderators of the relationship between stalking victimization and depression. Based on the reformulated learned helplessness theory, which emphasizes the role of internal, global, and stable attributions for negative events in the development of depression, we predicted that the association between stalking victimization and depression would be mediated by attributions for the stalking and characterological self-blame. We predicted that the association between stalking victimization and helplessness attributions or characterological self-blame, in turn, would be moderated by gender, sex-role identity, and length of stalking. Specifically, we hypothesized that female victims, victims possessing a feminine sex-role identity, and victims experiencing longer stalking episodes would be more likely to experience depression in comparison with male victims, victims possessing a masculine sex-role identity, and victims experiencing shorter stalking episodes. The results indicated that global attributions for the cause of stalking significantly mediated the relationship between stalking victimization and depression. The results for stable attributions, internal attributions, and characterological self-blame were nonsignificant. Furthermore, gender, sex-role identity, and length of stalking did not moderate the association between stalking and attributional style or characterological self-blame. The implications of these findings and directions for future research are discussed.

  14. Effect of harvest time and field retting duration on the chemical composition, morphology and mechanical properties of hemp fibers

    DEFF Research Database (Denmark)

    Liu, Ming; Fernando, Dinesh; Daniel, Geoffrey

    2015-01-01

    tThe large variability in the mechanical properties of hemp fibers is an issue in relation to their use inhigh-grade composites. The objective of the present study was to determine the optimal growth stage forharvesting hemp fibers for use in composites and to evaluate the effect of field retting......% at seed maturity.A highly significant reduction in cellulose deposition in fiber cell walls was reflected by reduced fiberwall thickness with plant maturity and was related to the development and ripening of hemp seeds.A statistically significant increase in lignin deposition and a slight decrease...... in pectins in hemp fibercell walls were also noted with stem maturity. Microscopy observations and histochemical analyzescorroborated the results from the chemical analyzes and revealed variations in morphological aspectsand spatial micro-distributions of carbohydrates and lignin within the cell structure...

  15. Nature & prevalence of stalking among New Zealand mental health clinicians.

    Science.gov (United States)

    Hughes, Frances A; Thom, Katey; Dixon, Robyn

    2007-04-01

    Stalking involves recurrent and persistent unwanted communication or contact that generates fear for safety in the victims. This pilot study evaluated the nature and prevalence of stalking among New Zealand nurses and physicians working in mental health services. An anonymous questionnaire asking respondents to describe their experiences with 12 stalking behaviors was distributed to 895 clinicians. Results indicated that regardless of discipline, women were more likely than men to have experienced one or more stalking behaviors, including receiving unwanted telephone calls, letters, and approaches; receiving personal threats: and being followed, spied on, or subject to surveillance. Women also reported higher levels of fearfulness as a consequence of stalking behaviors. Nearly half of the stalkers were clients; the remaining were former partners, colleagues, or acquaintances. In client-related cases, the majority of respondents told their colleagues and supervisors first, and the majority found them to be the most helpful resource. The results of this pilot study indicate a need for further research focused on the stalking of mental health clinicians in New Zealand and for development of workplace policies for adequate response to the stalking of mental health clinicians.

  16. The prevalence and nature of stalking in the Australian community.

    Science.gov (United States)

    Purcell, Rosemary; Pathé, Michele; Mullen, Paul E

    2002-02-01

    This study examines the extent and nature of stalking victimisation in a random community sample. A postal survey was distributed to 3700 adult men and women selected from the electoral roll in the State of Victoria. Outcome measures included the lifetime and annual cumulative incidence of stalking, the duration and methods of harassment, rates of associated violence and responses to victimisation. Almost one in four respondents (23.4%;432) had been stalked, the unwanted behaviour they were subjected to being both repeated and fear-provoking. One in 10 (197) had experienced a protracted course of stalking involving multiple intrusions spanning a period of at least one month. Women were twice as likely as men to report having been stalked at some time in their lives, though the rates of victimisation in the 12 months prior to the study did not differ significantly according to gender. Younger people were significantly more likely than older respondents to report having been stalked. Victims were pursued by strangers in 42% of cases. The most common methods of harassment involved unwanted telephone calls, intrusive approaches and following. Associated threats (29%) and physical assaults (18%) frequently arose out of the stalking. Significant social and economic disruption was created by the stalking for 63% of victims. Most sought assistance to manage their predicament (69%). The experience of being stalked is common and appears to be increasing. Ten percent of people have been subjected at some time to an episode of protracted harassment. Assaults by stalkers are disturbingly frequent. Most victims report significant disruption to their daily functioning irrespective of exposure to associated violence.

  17. Molecular cytogenetic analysis of monoecious hemp (Cannabis sativa L.) cultivars reveals its karyotype variations and sex chromosomes constitution.

    Science.gov (United States)

    Razumova, Olga V; Alexandrov, Oleg S; Divashuk, Mikhail G; Sukhorada, Tatiana I; Karlov, Gennady I

    2016-05-01

    Hemp (Cannabis sativa L., 2n = 20) is a dioecious plant. Sex expression is controlled by an X-to-autosome balance system consisting of the heteromorphic sex chromosomes XY for males and XX for females. Genetically monoecious hemp offers several agronomic advantages compared to the dioecious cultivars that are widely used in hemp cultivation. The male or female origin of monoecious maternal plants is unknown. Additionally, the sex chromosome composition of monoecious hemp forms remains unknown. In this study, we examine the sex chromosome makeup in monoecious hemp using a cytogenetic approach. Eight monoecious and two dioecious cultivars were used. The DNA of 210 monoecious plants was used for PCR analysis with the male-associated markers MADC2 and SCAR323. All monoecious plants showed female amplification patterns. Fluorescence in situ hybridization (FISH) with the subtelomeric CS-1 probe to chromosomes plates and karyotyping revealed a lack of Y chromosome and presence of XX sex chromosomes in monoecious cultivars with the chromosome number 2n = 20. There was a high level of intra- and intercultivar karyotype variation detected. The results of this study can be used for further analysis of the genetic basis of sex expression in plants.

  18. Utilization of enzyme supplemented Telfairia occidentalis stalk ...

    African Journals Online (AJOL)

    An eight (8) week feeding trial was carried out to assess the use of enzyme natuzyme supplemented Telfairia occidentalis stalk extract as growth inducer in the practical diet for Oreochromis niloticus fingerlings. Five isonitrogenous (35% crude protein) diets at 0 ml of stalk extract and enzyme (TRT 1), 15 ml (TRT 2) and 30 ...

  19. [Mental health impact of stalking in men and women].

    Science.gov (United States)

    Kuehner, Christine; Gass, Peter; Dressing, Harald

    2006-08-01

    Using data from the Mannheim stalking study, the present report analyses gender differences with regard to various mental health indicators and potential mediator effects of stalking victimization. Furthermore, we were interested in whether the impact of stalking on mental health was comparable for men and women. The study included a postal survey of 675 community residents on the experience of intruding harassment and on mental health indicators. In the Patient Health Questionnaire (PHQ-D, Lowe et al. 2001), women scored higher on most of the subscales (depression, anxiety, somatic complaints, stress, psychosocial impairment) than men. Furthermore, more women fulfilled criteria for at least one threshold or subthreshold mental disorder syndrome according to DSM-IV, and more women were under psychotropic medication. However, the identified associations were completely mediated by the higher prevalence of stalking victims in women. In contrast, the associations of stalking victimization with poor mental health, psychosocial functioning, and use of medication were largely comparable across gender.

  20. Compositional changes in industrial hemp biomass (Cannabis sativa L.) induced by electron beam irradiation Pretreatment

    International Nuclear Information System (INIS)

    Sung, Yong Joo; Shin, Soo-Jeong

    2011-01-01

    The effects of electron beam irradiation on chemical decomposition of industrial hemp biomass were evaluated at doses of 150, 300, and 450 kGy. The quantity of decomposed components was indirectly estimated by measuring changes in alkaline extraction. The more severe degradation of structural components induced by higher irradiation doses resulted in larger amounts of alkaline extract. Carbohydrate compositional analysis using 1 H-NMR spectroscopy was applied to quantitatively investigate changes in the polysaccharides of the industrial hemp. The xylose peak intensity in the NMR spectra decreased with increasing electron irradiation dose, indicating that xylan was more sensitive to electron beam irradiation than cellulose. -- Highlights: → The more severe degradation of structural components induced by higher irradiation. → Carbohydrate analysis was applied to quantitatively investigate changes in the industrial hemp. → Xylan was more sensitive to electron beam irradiation than cellulose.

  1. Compositional changes in industrial hemp biomass (Cannabis sativa L.) induced by electron beam irradiation Pretreatment

    Energy Technology Data Exchange (ETDEWEB)

    Sung, Yong Joo [Department of Biobased Materials, College of Agriculture and Life Science, Chungnam National University, Daejeon 305-764 (Korea, Republic of); Shin, Soo-Jeong [Department of Wood and Paper Science, College of Agriculture and Life Science, Chungbuk National University, Cheongju 361-763 (Korea, Republic of)

    2011-07-15

    The effects of electron beam irradiation on chemical decomposition of industrial hemp biomass were evaluated at doses of 150, 300, and 450 kGy. The quantity of decomposed components was indirectly estimated by measuring changes in alkaline extraction. The more severe degradation of structural components induced by higher irradiation doses resulted in larger amounts of alkaline extract. Carbohydrate compositional analysis using {sup 1}H-NMR spectroscopy was applied to quantitatively investigate changes in the polysaccharides of the industrial hemp. The xylose peak intensity in the NMR spectra decreased with increasing electron irradiation dose, indicating that xylan was more sensitive to electron beam irradiation than cellulose. -- Highlights: {yields} The more severe degradation of structural components induced by higher irradiation. {yields} Carbohydrate analysis was applied to quantitatively investigate changes in the industrial hemp. {yields} Xylan was more sensitive to electron beam irradiation than cellulose.

  2. Influence of agroclimatic conditions on content of main cannabinoids in industrial hemp (Cannabis sativa L.

    Directory of Open Access Journals (Sweden)

    Sikora Vladimir

    2011-01-01

    Full Text Available In a six-year field experiment eight industrial hemp varieties were examined for ∆9-tetrahydrocannabinol (THC and cannabidiol (CBD contents. The study analyzed the influence of growing degree days (GDD, soil temperature at 5 cm, air humidity, and growing season precipitation on the levels of the main cannabinoids in this crop. Agroclimatic conditions do not influence THC and CBD contents in industrial hemp in the same way. THC synthesis and accumulation are under the significant positive influence of GDD and air humidity and under the negative influence of precipitation, while soil temperature at 5 cm has no significant effect on it. Soil temperature at 5 cm has a significant positive effect on the CBD content, as do GDD. Precipitation has a negative influence on the CBD content of industrial hemp, while air humidity has no influence on it.

  3. Experimental Study on the Hygrothermal Behavior of a Coated Sprayed Hemp Concrete Wall

    Directory of Open Access Journals (Sweden)

    Anthony Magueresse

    2013-01-01

    Full Text Available Hemp concrete is a sustainable lightweight concrete that became popular in the field of building construction because of its thermal and environmental properties. However; available experimental data on its hygrothermal behavior are rather scarce in the literature. This paper describes the design of a large-scale experiment developed to investigate the hygrothermal behavior of hemp concrete cast around a timber frame through a spraying process; and then coated with lime-based plaster. The equipment is composed of two climatic chambers surrounding the tested wall. The experiment consists of maintaining the indoor climate at constant values and applying incremental steps of temperature; relative humidity or vapor pressure in the outdoor chamber. Temperature and relative humidity of the room air and on various depths inside the wall are continuously registered during the experiments and evaporation phenomena are observed. The influence of the plaster on the hygrothermal behavior of hemp concrete is investigated. Moreover; a comparison of experimental temperatures with numerical results obtained from a purely conductive thermal model is proposed. Comparing the model with the measured data gave satisfactory agreement.

  4. Stalk-length-dependence of the contractility of Vorticella convallaria

    Science.gov (United States)

    Gul Chung, Eun; Ryu, Sangjin

    2017-12-01

    Vorticella convallaria is a sessile protozoan of which the spasmoneme contracts on a millisecond timescale. Because this contraction is induced and powered by the binding of calcium ions (Ca2+), the spasmoneme showcases Ca2+-powered cellular motility. Because the isometric tension of V. convallaria increases linearly with its stalk length, it is hypothesized that the contractility of V. convallaria during unhindered contraction depends on the stalk length. In this study, the contractile force and energetics of V. convallaria cells of different stalk lengths were evaluated using a fluid dynamic drag model which accounts for the unsteadiness and finite Reynolds number of the water flow caused by contracting V. convallaria and the wall effect of the no-slip substrate. It was found that the contraction displacement, peak contraction speed, peak contractile force, total mechanical work, and peak power depended on the stalk length. The observed stalk-length-dependencies were simulated using a damped spring model, and the model estimated that the average spring constant of the contracting stalk was 1.34 nN µm-1. These observed length-dependencies of Vorticella’s key contractility parameters reflect the biophysical mechanism of the spasmonemal contraction, and thus they should be considered in developing a theoretical model of the Vorticella spasmoneme.

  5. Performance of four European hemp cultivars cultivated under different agronomic experimental conditions in the Eastern Cape Province, South Africa

    CSIR Research Space (South Africa)

    Blouw, LS

    2005-10-01

    Full Text Available of Fibre Hemp, Publication Agricultural Engineering, 31, University of Helsinki, 2001. 8. H.S. Sankari, Comparison of Bast Fibre Yield and Mechanical Fibre Properties of Hemp (Cannabis sativa L) cultivars, Industrial Crops and Products, 11, 73-84, 2000...

  6. Yield survey and nutritional evaluation of garlic stalk for ruminant feed.

    Science.gov (United States)

    Lee, Y H; Kim, Y I; Oh, Y K; Ahmadi, F; Kwak, W S

    2017-01-01

    Very limited information exists on the ruminal degradation kinetics of nutrients in garlic stalk. The present study aimed to survey the annual yield of garlic stalk in Korea and determine its feed-nutritive value for ruminants. In Experiment 1, garlic stalk was incubated in situ in the rumen of two Hanwoo steers (360 ± 15 kg body weight) and removed after 12, 24, or 48 h to determine the ruminal degradation kinetics of DM and NDF. Rice straw was also included for comparison. In Experiment 2, In Experiment 2, six male Corriedale sheep were randomized to two dietary treatments to determine the apparent digestibility of nutrients in garlic stalk. Diets included a control ration without garlic stalk (60% concentrate mix +40% ryegrass) or a treatment ration (70% control diet +30% garlic stalk). The Korean national yield of garlic stalk (sun-dried basis) in 2016 was estimated to be 31,910 tons, with the southern coastal regions producing the highest quantity. Compared with rice straw, garlic stalk had lower NDF, higher ADF, and greater effective degradabilities of DM and NDF, resulting in a greater TDN value (56.3%), which was higher than that obtained for rice straw (43.7%). These results provide basic information on the ruminal DM and NDF degradation kinetics of garlic stalk, which would be helpful for the efficient utilization of this by-product in ruminant diets.

  7. Yield survey and nutritional evaluation of garlic stalk for ruminant feed

    Directory of Open Access Journals (Sweden)

    Y. H. Lee

    2017-10-01

    Full Text Available Abstract Background Very limited information exists on the ruminal degradation kinetics of nutrients in garlic stalk. The present study aimed to survey the annual yield of garlic stalk in Korea and determine its feed-nutritive value for ruminants. Methods In Experiment 1, garlic stalk was incubated in situ in the rumen of two Hanwoo steers (360 ± 15 kg body weight and removed after 12, 24, or 48 h to determine the ruminal degradation kinetics of DM and NDF. Rice straw was also included for comparison. In Experiment 2, In Experiment 2, six male Corriedale sheep were randomized to two dietary treatments to determine the apparent digestibility of nutrients in garlic stalk. Diets included a control ration without garlic stalk (60% concentrate mix +40% ryegrass or a treatment ration (70% control diet +30% garlic stalk. Results The Korean national yield of garlic stalk (sun-dried basis in 2016 was estimated to be 31,910 tons, with the southern coastal regions producing the highest quantity. Compared with rice straw, garlic stalk had lower NDF, higher ADF, and greater effective degradabilities of DM and NDF, resulting in a greater TDN value (56.3%, which was higher than that obtained for rice straw (43.7%. Conclusion These results provide basic information on the ruminal DM and NDF degradation kinetics of garlic stalk, which would be helpful for the efficient utilization of this by-product in ruminant diets.

  8. Clinical and radiological features of pituitary stalk lesions in children and adolescents

    Directory of Open Access Journals (Sweden)

    Sung Chul Yoon

    2014-12-01

    Full Text Available PurposeThe diagnosis of pituitary stalk lesion has been based on clinical feature, radiologic assessment for its critical location and role. This study aimed to investigate clinical symptoms, endocrine disturbance, magnetic resonance imaging (MRI findings of pituitary stalk lesions in children and adolescents and to evaluate differences between neoplastic lesions with the others.MethodsWe performed a retrospective review of patients under 18 years old with pituitary stalk lesions diagnosed at the Seoul National University Children's Hospital between 2000 and 2013, by a text search for head MRI reports by using 'pituitary stalk', 'infundibulum', and 'infundibular stalk', as keywords.ResultsFor the 76 patients, sixteen patients (21.1% had congenital lesions, and 52 (68.4% had neoplasms. No inflammatory lesions were found. Diabetes insipidus (DI was the most common endocrine defect, diagnosed in 38 patients (50%. There was male predominance especially in neoplastic group. Thickened pituitary stalk was, but enhancement of lesion was not, associated with neoplasm. DI was more prevalent in neoplastic stalk lesions. Anterior pituitary dysfunction such as growth hormone and adrenocorticotropic hormone deficiencies were less prevalent in neoplastic lesions of pituitary stalk.ConclusionIn conclusion, the etiology of pituitary stalk lesions in children and adolescents is diverse and different from that in adults. Neoplastic pituitary stalk lesions can be differentiated from nonneoplastic lesions by systemic evaluation of clinical, hormonal, radiological findings.

  9. Stalking: terrorism at our doors--how social workers can help victims fight back.

    Science.gov (United States)

    Spitz, Mary-Ann Leitz

    2003-10-01

    Stalking is a dangerous and devastating crime that irrevocably changes the lives of victims but is frequently misunderstood and minimized. Victims report that their lives are never the same after they have been stalked. Stalking is prevalent and gender-neutral and occurs across all socioeconomic lines and in all clinical settings. The prevalence of stalking provides many opportunities for social workers to intervene, but first they must recognize and understand the problem. This article explains common misconceptions about stalking, contains a brief discussion of the types of stalking, the elements necessary to criminally charge someone with stalking, strategies for the victims, and suggestions for future research.

  10. Composite Materials Based on Hemp and Flax for Low-Energy Buildings

    Science.gov (United States)

    Brzyski, Przemysław; Barnat-Hunek, Danuta; Suchorab, Zbigniew; Łagód, Grzegorz

    2017-01-01

    The article presents the results obtained in the course of a study on prospective application of flax/hemp wastes as a filling material of lime-based composites in the construction of low-energy buildings. The utilized filler comprised the hydrated lime with clay and Portland cement used as additives. The analysis involved evaluation of such properties as porosity, density, thermal conductivity, absorptivity, permeability, as well as compressive and flexural strength. Depending on the quantity of the filler, the properties of the composite changed. This, in turn, enabled to evaluate whether the utilized composite met the thermal requirements established for low-energy buildings. Afterwards, the obtained data were cross-referenced with the results gathered in the case of a room built of autoclaved aerated concrete. In order to prevent reaching the critical surface humidity, the internal surface temperature had to be calculated. Moreover, the chances of interstitial condensation occurring in the wall made of the analyzed lime–flax–hemp composite were determined as well. The study showed that the composite exhibits low strength, low density, low thermal conductivity, and high absorptivity. The external walls made of the lime–flax–hemp composite receive a limited exposure to condensation, but not significant enough to constitute any threat. The requirements established for low-energy buildings can be met by using the analyzed composite. PMID:28772871

  11. Pro-technological and functional characterization of lactic acid bacteria to be used as starters for hemp (Cannabis sativa L.) sourdough fermentation and wheat bread fortification.

    Science.gov (United States)

    Nionelli, Luana; Montemurro, Marco; Pontonio, Erica; Verni, Michela; Gobbetti, Marco; Rizzello, Carlo Giuseppe

    2018-08-20

    Lactic acid bacteria were isolated from hemp (Cannabis sativa L.) flour, spontaneously fermented dough, and type I sourdough. Isolates were identified and further selected based on pro-technological, nutritional and functional properties. Lactobacillus plantarum/s5, Pediococcus acidilactici/s5, and Leuconostoc mesenteroides/s1 were used as mixed starter to produce hemp sourdough. Significant decreases of the concentration of phytic acid, condensed tannins, and total saponins were observed during fermentation. The in vitro protein digestibility increased up to 90%. Experimental wheat breads were made adding 5% to 15% (w/w) hemp sourdough to the formula, characterized, and compared to baker's yeast wheat bread manufactured without hemp sourdough. The use of hemp sourdough improved the textural features of wheat bread, without adversely affect the sensory profile. Proportionally to the fortification with hemp sourdough, protein digestibility of the breads increased, while the predicted glycemic index significantly decreased (87 vs 100%). This work demonstrated that the fermentation with selected starters improved nutritional functionality of hemp flour, allowing its large-scale use in different food applications, meeting the consumers and producers request for novel fermented baked goods with a well-balanced nutritional profile. Copyright © 2018 Elsevier B.V. All rights reserved.

  12. Planting date and seeding rate effects on sunn hemp biomass and nitrogen production for a winter cover crop

    Science.gov (United States)

    Sunn hemp (Crotalaria juncea L.) is a tropical legume that produces plant biomass and nitrogen (N) quickly. Our objectives were to assess the growth of a new sunn hemp cultivar breed to produce seed in a temperate climate and determine the residual N effect on a subsequent rye (Secale cereale L.) wi...

  13. Stalking: The term, features and proposals de lege ferenda

    Directory of Open Access Journals (Sweden)

    Ranđelović Višnja M.

    2016-01-01

    Full Text Available In the paper author analyzes main features of stalking, which is recognized as a serious problem in many countries and provided as a criminal offense. There are presented comparative legela solutions of this criminal offense in the countries that have incriminated it firs, as well as in neighboring countries. In recent years in Republic of Serbia it has been indicated to prevalence of the stalking, especially among the former partners, and considering that there is a need for such behavior to be incriminated. Also, Serbia's ratification of the Council of Europe Convention on Preventing and Combating Violence against Women and Domestic Violence assumed an obligation to prescribe stalking as criminal offense. This paper proposes the possible way of prescribing stalking with analysis of certain elements of the legal description.

  14. Mechanical Properties and Weathering Behavior of Polypropylene-Hemp Shives Composites

    Directory of Open Access Journals (Sweden)

    Marcel Ionel Popa

    2013-01-01

    Full Text Available This paper presents the obtaining and the characterization of composites with polypropylene matrix and hemp shives as filler in different ratios and containing poly(propylene-co maleic anhydride (MAH-PP 3% wt as compatibility agent. The weathering behavior of the composite enclosing 60% hemp shives, performed after the exposure to UV radiations at different exposure times, was evaluated. The changes in the chemical and morphological structures were investigated by FT-IR and RAMAN spectroscopies and AFM microscopy. The mechanical characteristics of the composites were determined before and after an artificial aging process, and they are within the limits of the values reported for polyolefin-based composites and materials with natural fillers. During the accelerated weathering process, the correlation between the chemical degradation of the main components of the composite and the modification of the mechanical properties after the process of aging has been observed.

  15. Do men and women differ in their perceptions of stalking: an exploratory study among college students.

    Science.gov (United States)

    Lambert, Eric G; Smith, Brad; Geistman, James; Cluse-Tolar, Terry; Jiang, Shanhe

    2013-01-01

    Stalking is a crime that can terrify its victims and ultimately take a severe emotional toll. Although a growing body of research has examined stalking experiences and reactions of victims, there has been far less research on whether men and women differ in their perceptions of stalking. Toward this end, a survey of college students at a large public 4-year Midwestern university was undertaken. We examined differences is how men and women view stalking and whether gender differences were moderated by prior stalking experience. Specifically, we examined whether there were gender differences in perceptions of the pervasiveness of stalking, the harm stalking does, who tends to be stalked, if stalking mainly involves former relational partners, possible motivations for stalking, the line between courtship and stalking, and notions of victim blaming. We found significant differences in stalking views between men and women on all the measures, except for perceptions of the line between courtship and stalking. Women tended to perceive stalking as more pervasive and harmful. Men were more likely to perceive stalking as involving strangers and to blame the victim for the stalking. Female and male respondents also differed in their perceptions of motivations for stalking. Prior victim stalking experience did not moderate the gender differences. Although being a prior stalking victim had a significant association with 4 of the 7 stalking perception variables, its effect sizes were smaller than that of gender.

  16. A New Type of Synthesis of 1,2,3-Thiadiazole and 1,2,3-Diazaphosphole Derivatives Via-Hurd-Mori Cyclization

    Directory of Open Access Journals (Sweden)

    Mona A. Hosny

    2012-01-01

    Full Text Available We present a short and efficient synthesis of the title compounds starting with cheap and readily available camphor and derivatives of acetophenone. The optimized sequence allows the large-scale preparation of this new type of synthesis in a few steps. New 1,2,3-thiadiazole and 1,2,3-diazaphosphole derivatives 11-20, were prepared from the ketones 1-5 via the corresponding semicarbazones 6-10. The Hurd-Mori and Lalezari methods were used, respectively, for the preparation of these 1,2,3-thiadiazole and 1,2,3-diazaphospholene derivatives. These derivatives exhibit anticancer effect due to their high potential biological activity.

  17. Integrated production of cellulosic bioethanol and succinic acid from industrial hemp in a biorefinery concept.

    Science.gov (United States)

    Kuglarz, Mariusz; Alvarado-Morales, Merlin; Karakashev, Dimitar; Angelidaki, Irini

    2016-01-01

    The aim of this study was to develop integrated biofuel (cellulosic bioethanol) and biochemical (succinic acid) production from industrial hemp (Cannabis sativa L.) in a biorefinery concept. Two types of pretreatments were studied (dilute-acid and alkaline oxidative method). High cellulose recovery (>95%) as well as significant hemicelluloses solubilization (49-59%) after acid-based method and lignin solubilization (35-41%) after alkaline H2O2 method were registered. Alkaline pretreatment showed to be superior over the acid-based method with respect to the rate of enzymatic hydrolysis and ethanol productivity. With respect to succinic acid production, the highest productivity was obtained after liquid fraction fermentation originated from steam treatment with 1.5% of acid. The mass balance calculations clearly showed that 149kg of EtOH and 115kg of succinic acid can be obtained per 1ton of dry hemp. Results obtained in this study clearly document the potential of industrial hemp for a biorefinery. Copyright © 2015 Elsevier Ltd. All rights reserved.

  18. 78 FR 1125 - National Stalking Awareness Month, 2013

    Science.gov (United States)

    2013-01-07

    ... some point in their lives, 1 in 6 women and 1 in 19 men will be stalked, and many of these crimes will.... It can include implied or explicit threats; harassment; or nonconsensual communication through phone..., stalking tends to escalate over time, and it is sometimes followed by sexual assault or homicide. My...

  19. Structural characterization of lignin from grape stalks (Vitis vinifera L.).

    Science.gov (United States)

    Prozil, Sónia O; Evtuguin, Dmitry V; Silva, Artur M S; Lopes, Luísa P C

    2014-06-18

    The chemical structure of lignin from grape stalks, an abundant waste of winemaking, has been studied. The dioxane lignin was isolated from extractive- and protein-free grape stalks (Vitis vinifera L.) by modified acidolytic procedure and submitted to a structural analysis by wet chemistry (nitrobenzene and permanganate oxidation (PO)) and spectroscopic techniques. The results obtained suggest that grape stalk lignin is an HGS type with molar proportions of p-hydroxyphenyl (H), guaiacyl (G) and syringyl (S) units of 3:71:26. Structural analysis by (1)H and (13)C NMR spectroscopy and PO indicates the predominance of β-O-4' structures (39% mol) in grape stalk lignin together with moderate amounts of β-5', β-β, β-1', 5-5', and 4-O-5' structures. NMR studies also revealed that grape lignin should be structurally associated with tannins. The condensation degree of grape stalks lignin is higher than that of conventional wood lignins and lignins from other agricultural residues.

  20. DYNAMICS OF LEAF PEROXIDASE ACTIVITY DURING ONTOGENY OF HEMP PLANTS, IN RELATION TO SEXUAL PHENOTYPE

    Directory of Open Access Journals (Sweden)

    Elena Truta

    2005-08-01

    Full Text Available During vegetation of female and male hemp plants (Cannabis sativa L., five quantitative determinations of peroxidase activities were made (40 days, 55 days, 70 days, 85 days, 105 days. Peroxidase activity presented some differences in hemp plants, between females and males, during their vegetation cycle. In female plants, before anthesis were registered peaks of peroxidase activities. The blossoming of male plants was coincident with the increase of catalitic action of peroxidase. Generally, the male plants displayed greater levels of peroxidasic activity.

  1. Hemp (Cannabis sativa L.).

    Science.gov (United States)

    Feeney, Mistianne; Punja, Zamir K

    2015-01-01

    Hemp (Cannabis sativa L.) suspension culture cells were transformed with Agrobacterium tumefaciens strain EHA101 carrying the binary plasmid pNOV3635. The plasmid contains a phosphomannose isomerase (PMI) selectable marker gene. Cells transformed with PMI are capable of metabolizing the selective agent mannose, whereas cells not expressing the gene are incapable of using the carbon source and will stop growing. Callus masses proliferating on selection medium were screened for PMI expression using a chlorophenol red assay. Genomic DNA was extracted from putatively transformed callus lines, and the presence of the PMI gene was confirmed using PCR and Southern hybridization. Using this method, an average transformation frequency of 31.23% ± 0.14 was obtained for all transformation experiments, with a range of 15.1-55.3%.

  2. Pituitary stalk compression by the dorsum sellae: possible cause for late childhood onset growth disorders.

    Science.gov (United States)

    Taoka, Toshiaki; Iwasaki, Satoru; Okamoto, Shingo; Sakamoto, Masahiko; Nakagawa, Hiroyuki; Otake, Shoichiro; Fujioka, Masayuki; Hirohashi, Shinji; Kichikawa, Kimihiko

    2006-06-01

    The purpose of this study was to evaluate the relationship between pituitary stalk compression by the dorsum sellae and clinical or laboratory findings in short stature children. We retrospectively reviewed magnetic resonance images of the pituitary gland and pituitary stalk for 34 short stature children with growth hormone (GH) deficiency and 24 age-matched control cases. We evaluated the degree of pituitary stalk compression caused by the dorsum sellae. Body height, GH level, pituitary height and onset age of the short stature were statistically compared between cases of pituitary stalk compression with associated stalk deformity and cases without compression. Compression of the pituitary stalk with associated stalk deformity was seen in nine cases within the short stature group. There were no cases observed in the control group. There were no significant differences found for body height, GH level and pituitary height between the cases of pituitary stalk compression with associated stalk deformity and cases without compression. However, a significant difference was seen in the onset age between cases with and without stalk compression. Pituitary stalk compression with stalk deformity caused by the dorsum sellae was significantly correlated with late childhood onset of short stature.

  3. Identification of metastases in the pituitary stalk

    Energy Technology Data Exchange (ETDEWEB)

    Schubiger, O

    1982-09-01

    Two cases of metastasis in the pituitary stalk are presented. In both cases, presenting with diabetes insipidus, the demonstration of a small (under 1 cm) metastasis in the pituitary stalk was possible using a current generation scanner. Patients with known primary tumors presenting with a diabetes insipidus should be examined by CT before therapy with antidiuretic hormone is initiated. In cases of visible metastasis, a specific therapy together with the hormone-substitution should be discussed.

  4. Behavioral and Mental Health Correlates of Youth Stalking Victimization

    Science.gov (United States)

    Reidy, Dennis E.; Smith-Darden, Joanne P.; Kernsmith, Poco D.

    2018-01-01

    Introduction Although recognized as a public health problem, little attention has been paid to the problem of stalking among youth. Latent profile analysis was used to identify latent groups of adolescent stalking victims and their behavioral and mental health correlates. Methods A cross-sectional sample of 1,236 youths were randomly selected from 13 schools stratified by community risk level (i.e., low, moderate, and high risk) and gender. Students completed surveys assessing behavioral indicators of stalking victimization, as well as substance use, sexual behavior, dating violence, and psychiatric symptoms. Data were collected in 2013 and data analyses were performed in 2015. Results Analysis indicated the presence of a non-victim class, a minimal exposure class, and a victim class for boys and girls alike. Approximately 14% of girls and 13% of boys were in the stalking victim class. Adolescents in the victim class reported more symptoms of post-traumatic stress, mood disorder, and hopelessness, as well as more instances of alcohol use, binge drinking, and physical dating violence victimization. Girls in the victim class also reported engaging in sexting behaviors and oral sex with significantly more partners than their non-victim peers. Conclusions These findings provide valuable knowledge of the prevalence and pertinent health correlates of stalking victimization in adolescence. The data suggest a substantial proportion of adolescents are victims of stalking and are likewise at risk for a number of deleterious health outcomes. As such, this population merits further attention by prevention researchers and practitioners. PMID:27743623

  5. Yield Potential of Hemp (Cannabis sativa L.) Cultivars in Denmark

    DEFF Research Database (Denmark)

    Deleuran, Lise Christina; Flengmark, Poul Kristiansen

    2005-01-01

    In order to determine the yield potential of fibre hemp in Denmark, defined as seed yield, biomass, stem and fibre production, five cultivars were evaluated in field trials at two sites during 1998-2000. The total dry matter yield, stem yield, fibre yield, fibre percent, plant height, and seed...

  6. Effect of Banana Stalk Organic Fertilizer on the Growth of Chinese Cabbage

    Institute of Scientific and Technical Information of China (English)

    Zheli; DING; Lina; HAN; Zhiqiang; JIN; Bizun; WANG; Huicai; ZENG; Wei; ZHENG; Yingdui; HE; Xiaoping; ZANG

    2016-01-01

    In order to solve the problem of waste disposal after banana harvest,we use banana stalk to produce banana stalk organic fertilizer,through a plot experiment. We compare the influence of normal organic fertilizer( Wanlubao) and banana stalk organic fertilizer as base fertilizers on Chinese cabbage growth,and evaluate the economic benefits of banana stalk organic fertilizer. The results show that organic fertilizer has little effect on water content and nutrient content of Chinese cabbage,but has significant effect on plant height and leaf width. Using organic fertilizer can increase the production of Chinese cabbage by 22. 50%- 43. 10%. With 6750 kg / ha normal organic fertilizer,Chinese cabbage gets the highest yield,which reaches 30135 kg / ha,followed by the treatment of 6750 kg / ha stalk organic fertilizer. At farmers’ conventional fertilization level( 4500 kg / ha),stalk organic fertilizer can increase the yield by more than 3. 50% in comparison with the normal organic fertilizer,and the economic benefit increases by 1800 yuan / ha. As a kind of banana waste cycling product,banana stalk organic fertilizer is of low cost and good effect,and can be used instead of normal organic fertilizer.

  7. Antifungal properties of Musa paradisiaca (Plantain) peel and stalk ...

    African Journals Online (AJOL)

    Effect of plantain (Musa paradisiaca (L) AAB genomic group) peel and stalk extracts were investigated using percentage inhibition test. Complete inhibition of growth (100%) was observed for Aspergillusniger, Aspergillus oryzae and Rhizopus stolonifer at 1.0 mg/ml concentration of stalk extract. Peel extract inhibited A.

  8. Stalking als Straftatbestand : Neue Tendenzen in den EU-Mitgliedstaaten

    NARCIS (Netherlands)

    van der Aa, Suzanne; Bachman, Roland; Ortiz-Müller, Wolf

    2017-01-01

    Article 34 of the Council of Europe Convention on Preventing and Combating Violence against Women and Domestic Violence obliges signatory states to criminalize stalking. This article provides an inventory of criminal anti-stalking legislation in the 28 EU Member States in order to see whether they

  9. Stalking of psychiatrists: psychopathological characteristics and gender differences in an Italian sample.

    Science.gov (United States)

    Mastronardi, Vincenzo M; Pomilla, Antonella; Ricci, Serafino; D'Argenio, Alberto

    2013-05-01

    Research has indicated that medical doctors and paramedics are at higher risk of being stalked than the general population. In particular, mental health care professionals alone represent one third of the victims of harassment. Because of the lack of studies in this specific sector, especially in Italy, in this study, we examined the stalking of psychiatrists by their patients, considering gender differences and the incidence of stalking in private practice and public mental health clinics in Rome. We found that the rate of stalking in private mental health settings is higher than that in public settings and that the perpetrators of stalking are mainly women who mostly target mental health professionals working in private practice. Implications of the findings are noted and discussed.

  10. Effect of introducing hemp oil into feed on the nutritional quality of pig meat

    Directory of Open Access Journals (Sweden)

    Mourot Jacques

    2015-11-01

    Full Text Available Research is being carried out to diversify the sources of n-3 fatty acid-rich lipids for animal feed. In this study, 3 batches of 12 pigs with between 50 and 105 kg of live weight, received isolipidic diets containing either palm oil (PO, or rapeseed oil (CO, or hemp oil (HO (providing respectively 0.6; 1.9 and 3.4 g of C18:3 n-3 (ALA /kg of feed. The quantity of ALA deposited in the meat is higher (p< 0.001 in the HO pigs. Hemp oil may be an interesting source of ALA to improve the nutritional quality of pork.

  11. Effect of Vermicompost Extract and Vermicompost-Derived Humic Acids on Seed Germination and Seedling Growth of Hemp

    Directory of Open Access Journals (Sweden)

    Ievinsh Gederts

    2017-08-01

    Full Text Available Hemp (Cannabis sativa L. cultivars grown for industrial use have recently emerged as a sustainable alternative source of industrial fibre and bioenergy, and is a highly valuable food and animal feed resource. The aim of the present study was to evaluate the effect of vermicompost extract, vermicompost mineral nutrient composition, and vermicompost-derived humic and fulvic acids on seed germination and growth of hemp seedlings. In general, separate application of all vermicompost components stimulated seed germination and hypocotyl and radicle growth, as well as increased chlorophyll concentration in cotyledons. Effective concentration range and the degree of stimulation varied significantly between the treatments. For practical purposes, application of vermicompost and vermicompost-derived extracts for stimulation of hemp growth could be useful at concentrations 5%, 0.05 mg·mL−1 and 1%, for vermicompost extract, humic acids and fulvic acids, respectively.

  12. Remote sensing techniques for monitoring the Rio Grande Valley cotton stalk destruction program

    Energy Technology Data Exchange (ETDEWEB)

    Richardson, A.J.; Gerbermann, A.H.; Summy, K.R.; Anderson, G.L. (Department of Agriculture, Weslaco, TX (United States))

    1993-09-01

    Post harvest cotton (Gossypium hirsutum L.) stalk destruction is a cultural practice used in the Rio Grande Valley to suppress over wintering populations of boll weevils (Anthonomus grandis Boheman) without using chemicals. Consistent application of this practice could substantially reduce insecticide usage, thereby minimizing environmental hazards and increasing cotton production profits. Satellite imagery registered within a geographic information system was used to monitor the cotton stalk destruction program in the Rio Grande Valley. We found that cotton stalk screening procedures based on standard multispectral classification techniques could not reliably distinguish cotton from sorghum. Greenness screening for cotton plant stalks after the stalk destruction deadline was possible only where ground observations locating cotton fields were available. These findings indicate that a successful cotton stalk destruction monitoring program will require satellite images and earth referenced data bases showing cotton field locations.

  13. Evaluation of elastic modulus and hardness of crop stalks cell walls by nano-indentation

    Science.gov (United States)

    Yan Wu; Siqun Wang; Dingguo Zhou; Cheng Xing; Yang Zhang; Zhiyong Cai

    2010-01-01

    Agricultural biomaterials such as crop stalks are natural sources of cellulosic fiber and have great potential as reinforced materials in bio-composites. In order to evaluate their potential as materials for reinforcement, the nano-mechanical properties of crop-stalk cell walls, i.e. those of cotton (Gossypium herbaceu) stalk, soybean (Glycine max) stalk, cassava (...

  14. Hemp yarn reinforced composites – III. Moisture content and dimensional changes

    DEFF Research Database (Denmark)

    Madsen, Bo; Hoffmeyer, Preben; Lilholt, Hans

    2012-01-01

    Based on a comprehensive set of experimental data it is demonstrated that the moisture properties of aligned hemp fibre yarn/thermoplastic matrix composites are showing low moisture sorption capacity and low dimensional changes. Using a reference humidity of 65% RH, and a common span of ambient...

  15. Evaluation of cotton stalk hydrolysate for xylitol production.

    Science.gov (United States)

    Sapcı, Burcu; Akpinar, Ozlem; Bolukbasi, Ufuk; Yilmaz, Levent

    2016-07-03

    Cotton stalk is a widely distributed and abundant lignocellulosic waste found in Turkey. Because of its rich xylose content, it can be a promising source for the production of xylitol. Xylitol can be produced by chemical or biotechnological methods. Because the biotechnological method is a simple process with great substrate specificity and low energy requirements, it is more of an economic alternative for the xylitol production. This study aimed to use cotton stalk for the production of xylitol with Candida tropicalis Kuen 1022. For this purpose, the combined effects of different oxygen concentration, inoculum level and substrate concentration were investigated to obtain high xylitol yield and volumetric xylitol production rate. Candida tropicalis Kuen 1022 afforded different concentrations of xylitol depending on xylose concentration, inoculum level, and oxygen concentration. The optimum xylose, yeast concentration, and airflow rate for cotton stalk hydrolysate were found as 10.41 g L(-1), 0.99 g L(-1), and 1.02 vvm, respectively, and under these conditions, xylitol yield and volumetric xylitol production rate were obtained as 36% and 0.06 g L(-1) hr(-1), respectively. The results of this study show that cotton stalk can serve as a potential renewable source for the production of xylitol.

  16. Utilization of bio-waste cotton ( Gossypium hirsutum L.) stalks and ...

    African Journals Online (AJOL)

    ... three-layer particleboard containing different cotton (Gossypium hirsutum L.) stalks and underutilized paulownia (paulownia fortunie) wood particle ratios (30, 50 and 70%) using urea formaldehyde resin. Addition of cotton stalk and paulownia wood in particleboard improved mechanical properties of resulting composites ...

  17. [Effects of hot-NaOH pretreatment on Jerusalem artichoke stalk composition and subsequent enzymatic hydrolysis].

    Science.gov (United States)

    Wang, Qing; Qiu, Jingwen; Li, Yang; Shen, Fei

    2015-10-01

    In order to explore the possibility of Jerusalem artichoke stalk for bioenergy conversion, we analyzed the main composition of whole stalk, pitch, and core of the stalk. Meanwhile, these parts were pretreated with different NaOH concentrations at 121 degrees C. Afterwards, enzymatic hydrolysis was performed to evaluate the pretreatment efficiency. Jerusalem artichoke stalk was characterized by relatively high lignin content (32.0%) compared with traditional crop stalks. The total carbohydrate content was close to that of crop stalks, but with higher cellulose content (40.5%) and lower hemicellulose (19.6%) than those of traditional crop stalks. After pretreatment, the lignin content in the whole stalk, pitch, and core decreased by 13.1%-13.4%, 8.3%-13.5%, and 19.9%-27.2%, respectively, compared with the unpretreated substrates. The hemicellulose content in the whole stalk, pitch, and core decreased 87.8%-96.9%, 87.6%-95.0%, and 74.0%-90.2%, respectively. Correspondingly, the cellulose content in the pretreated whole stalk, pitch, and core increased by 56.5%-60.2%, 52.2%-55.4%, and 62.7%-73.2%, respectively. Moreover, increase of NaOH concentration for pretreatment could improve the enzymatic hydrolysis of the whole stalk and pitch by 2.3-2.6 folds and 10.3-18.5 folds, respectively. The hydrolysis of pretreated stalk core decreased significantly as 2.0 mol/L NaOH was employed, although the increased NaOH concentration can also improve its hydrolysis performance. Based on these results, hot-NaOH can be regarded as an option for Jerusalem artichoke stalk pretreatment. Increasing NaOH concentration was beneficial to hemicellulose and lignin removal, and consequently improved sugar conversion. However, the potential decrease of sugar conversion of the pretreated core by higher NaOH concentration suggested further optimization on the pretreatment conditions should be performed.

  18. Stalking by patients: doctors' experiences in a Canadian urban area (Part II)--physician responses.

    Science.gov (United States)

    Abrams, Karen M; Robinson, Gail Erlick

    2013-07-01

    Stalking involves recurrent unwanted communication, harassment, and intrusive behaviors. The aim of this study was to examine physicians' experiences of being stalked by their patients, with particular attention to the emotional impact on the physicians and their actions taken. A questionnaire designed to study the nature and the impact of stalking experiences among physicians was sent to 3159 randomly chosen physicians in the Greater Toronto Area. Approximately 15% (14.9%) of the 1190 physicians who responded reported having been stalked. The physicians reported feeling angry, frustrated, anxious, frightened, lacking control, and helpless. The physicians coped in a number of ways including terminating the physician-patient relationship, but many just ignored the problem. Most had no previous knowledge about stalking. Physicians experience a range of emotions as a result of being a victim of stalking. In view of the prevalence and the impact, physicians may benefit from education to help prepare them for the possibility of being stalked.

  19. The effect of particle shape and size distribution on the acoustical properties of mixtures of hemp particles.

    Science.gov (United States)

    Glé, Philippe; Gourdon, Emmanuel; Arnaud, Laurent; Horoshenkov, Kirill-V; Khan, Amir

    2013-12-01

    Hemp concrete is an attractive alternative to traditional materials used in building construction. It has a very low environmental impact, and it is characterized by high thermal insulation. Hemp aggregate particles are parallelepiped in shape and can be organized in a plurality of ways to create a considerable proportion of open pores with a complex connectivity pattern, the acoustical properties of which have never been examined systematically. Therefore this paper is focused on the fundamental understanding of the relations between the particle shape and size distribution, pore size distribution, and the acoustical properties of the resultant porous material mixture. The sound absorption and the transmission loss of various hemp aggregates is characterized using laboratory experiments and three theoretical models. These models are used to relate the particle size distribution to the pore size distribution. It is shown that the shape of particles and particle size control the pore size distribution and tortuosity in shiv. These properties in turn relate directly to the observed acoustical behavior.

  20. Nutritive quality of romanian hemp varieties (Cannabis sativa L. with special focus on oil and metal contents of seeds

    Directory of Open Access Journals (Sweden)

    Mihoc Marcela

    2012-10-01

    Full Text Available Abstract Background The study aims to determine the nutritional value of hemp seed expressed by the oil content and by the concentration of metals (Ca, Mg, K, Fe, Mn, Zn and Cd, for five varieties of monoecious and dioecious hemp seeds approved in Romania, comparative with the concentration of these metals in the soil. Results The content of oil in hempseed registers a slight decrease in the production records of 2011, losses due to drought and low levels of precipitation during the growth period. The greatest loss is found in Diana monoecious variety (26.54-20.82% followed by Zenit varieties (27.37-22.97%, Armanca (29.27-25.32%, Silvana (28.89-25.04% and Denise (26.96-25.30%. Siccative hemp oil has a yellowish green color and an iodine index of 140–156 g I2/100 g oil. Hemp seed are rich in mineral based Ca (144–955 mg/100 g seed, Mg (237–694 mg/100 g seed, K (463–2821 mg/100 g seed, Fe (1133-2400 mg.kg-1, Mn (63–110 mg.kg-1 and Zn (42-94 mg.kg-1. For the soil the following macroelements concentrations were determined: Ca (2100–2520 mg.kg-1, Mg (320–376 mg.kg-1 and K (232–257 mg.kg-1. Mn (156–197 mg.kg-1 and Zn (54–67 mg.kg-1 remain within normal limits for Romania. The soils in the experience area contain large amounts of Fe (19000–20430 mg.kg-1. The presence of K in large quantities determines the accumulation of large quantities of Fe in the soil. Conclusion Hempseed belonging to the five Romanian varieties are rich source of nutrients (Ca, Mg, K and unsaturated oil easily digestible by the body, but the presence of Cd concentrations above the upper limit puts a question mark over the use of seeds in various food products. Hemp extracts easily certain metals from the soil. Significant amounts of Fe (1133–2400 mg.kg-1, Mn (63–110 mg.kg-1, Zn (42–94 mg.kg-1 and Cd (1.3-4.0 mg.kg-1 are found in hemp seeds. Hemp (Cannabis sativa L. is included among plants suitable for phytoremediation of soil contaminated with cadmium

  1. Radiation-induced grafting of sweet sorghum stalk for copper(II) removal from aqueous solution

    International Nuclear Information System (INIS)

    Dong, Jing; Hu, Jun; Wang, Jianlong

    2013-01-01

    Highlights: • Radiation-induced grafting was used to modify the stalk. • Cellulose, hemicellulose and lignin participated in grafting reaction. • Both the structure and composition of stalk had influence on grafting. • The sorption capacity of the grafted stalk increased about five times. -- Abstract: The influence of main components (cellulose, hemicellulose and lignin) of the sweet sorghum stalk on radiation-induced grafting reaction and adsorption of copper from aqueous solution was investigated. Sweet sorghum stalk was grafted with acrylic acid induced by γ-irradiation. The results showed that the grafted stalk contained 1.6 mmol/g carboxyl groups, and its maximal adsorption capacity was 13.32 mg/g. The cellulose, hemicellulose and lignin of the raw materials were confirmed to involve in grafting reaction through comparing the grafting yield and the structure of the grafted materials. Both the structure and the composition of the sweet sorghum stalk had influence on the grafting reaction and adsorption capacity. The adsorption capacity of the grafted sweet sorghum stalk increased about five times, and the adsorption isotherm of the grafted materials conformed to the Langmuir model. The main mechanism for copper adsorption involved in ion exchange

  2. Report of a Working Group on Fibre Crops (Flax and Hemp)

    NARCIS (Netherlands)

    Bas, N.; Pavelek, M.; Maggioni, L.; Lipman, E.

    2007-01-01

    Members of the newly established ECPGR Working Group on Fibre Crops (Flax and Hemp), in the framework of Sugar, Starch and Fibre Crops Network, met for the first time at Wageningen, the Netherlands on 14–16 June 2006. Fifteen participants from the Czech Republic, Germany, Hungary, Italy, Latvia,

  3. Selective Predation of a Stalking Predator on Ungulate Prey.

    Directory of Open Access Journals (Sweden)

    Marco Heurich

    Full Text Available Prey selection is a key factor shaping animal populations and evolutionary dynamics. An optimal forager should target prey that offers the highest benefits in terms of energy content at the lowest costs. Predators are therefore expected to select for prey of optimal size. Stalking predators do not pursue their prey long, which may lead to a more random choice of prey individuals. Due to difficulties in assessing the composition of available prey populations, data on prey selection of stalking carnivores are still scarce. We show how the stalking predator Eurasian lynx (Lynx lynx selects prey individuals based on species identity, age, sex and individual behaviour. To address the difficulties in assessing prey population structure, we confirm inferred selection patterns by using two independent data sets: (1 data of 387 documented kills of radio-collared lynx were compared to the prey population structure retrieved from systematic camera trapping using Manly's standardized selection ratio alpha and (2 data on 120 radio-collared roe deer were analysed using a Cox proportional hazards model. Among the larger red deer prey, lynx selected against adult males-the largest and potentially most dangerous prey individuals. In roe deer lynx preyed selectively on males and did not select for a specific age class. Activity during high risk periods reduced the risk of falling victim to a lynx attack. Our results suggest that the stalking predator lynx actively selects for size, while prey behaviour induces selection by encounter and stalking success rates.

  4. Improving enzymatic hydrolysis of industrial hemp (Cannabis sativa L.) by electron beam irradiation

    International Nuclear Information System (INIS)

    Shin, Soo-Jeong; Sung, Yong Joo

    2008-01-01

    The electron beam irradiation was applied as a pretreatment of the enzymatic hydrolysis of hemp biomass with doses of 150, 300 and 450 kGy. The higher irradiation dose resulted in the more extraction with hot-water extraction or 1% sodium hydroxide solution extraction. The higher solubility of the treated sample was originated from the chains scission during irradiation, which was indirectly demonstrated by the increase of carbonyl groups as shown in diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) spectra. The changes in the micro-structure of hemp resulted in the better response to enzymatic hydrolysis with commercial cellulases (Celluclast 1.5L and Novozym 342). The improvement in enzymatic hydrolysis by the irradiation was more evident in the hydrolysis of the xylan than in that of the cellulose

  5. Improving enzymatic hydrolysis of industrial hemp ( Cannabis sativa L.) by electron beam irradiation

    Science.gov (United States)

    Shin, Soo-Jeong; Sung, Yong Joo

    2008-09-01

    The electron beam irradiation was applied as a pretreatment of the enzymatic hydrolysis of hemp biomass with doses of 150, 300 and 450 kGy. The higher irradiation dose resulted in the more extraction with hot-water extraction or 1% sodium hydroxide solution extraction. The higher solubility of the treated sample was originated from the chains scission during irradiation, which was indirectly demonstrated by the increase of carbonyl groups as shown in diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) spectra. The changes in the micro-structure of hemp resulted in the better response to enzymatic hydrolysis with commercial cellulases (Celluclast 1.5L and Novozym 342). The improvement in enzymatic hydrolysis by the irradiation was more evident in the hydrolysis of the xylan than in that of the cellulose.

  6. Improving enzymatic hydrolysis of industrial hemp (Cannabis sativa L.) by electron beam irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Shin, Soo-Jeong [Chungbuk National University, Cheongju, Chungbuk 361-763 (Korea, Republic of); Sung, Yong Joo [KT and G Central Research Institute, 302 Shinseong-Dong, Yuseong-Gu, Daejeon 305-805 (Korea, Republic of)], E-mail: yosung17@yahoo.co.kr

    2008-09-15

    The electron beam irradiation was applied as a pretreatment of the enzymatic hydrolysis of hemp biomass with doses of 150, 300 and 450 kGy. The higher irradiation dose resulted in the more extraction with hot-water extraction or 1% sodium hydroxide solution extraction. The higher solubility of the treated sample was originated from the chains scission during irradiation, which was indirectly demonstrated by the increase of carbonyl groups as shown in diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) spectra. The changes in the micro-structure of hemp resulted in the better response to enzymatic hydrolysis with commercial cellulases (Celluclast 1.5L and Novozym 342). The improvement in enzymatic hydrolysis by the irradiation was more evident in the hydrolysis of the xylan than in that of the cellulose.

  7. Stalking Victimization among College Women and Subsequent Help-Seeking Behaviors

    Science.gov (United States)

    Buhi, Eric R.; Clayton, Heather; Surrency, Heather Hepler

    2009-01-01

    Objective: The authors examined the incidence of stalking victimization and subsequent help-seeking behaviors among college women. Participants and Methods: A stratified random sample of college women (N = 391) completed an anonymous Internet-based questionnaire in spring 2006. Results: One-fifth of women reported stalking victimization while…

  8. Briquetting of Charcoal from Sesame Stalk

    Directory of Open Access Journals (Sweden)

    Alula Gebresas

    2015-01-01

    Full Text Available Due to the easy availability of wood in Ethiopia, wood charcoal has been the main source fuel for cooking. This study has been started on sesame stalk biomass briquetting which can potentially solve the health problems and shortage of energy, which consequently can solve deforestation. The result of the data collection shows that, using 30% conversion efficiency of carbonizer, it was found that more than 150,000 tonnes of charcoal can be produced from the available sesame stalk in Humera, a place in north Ethiopia. The clay binders that are mixed with carbonized sesame stalk were found to have 69 liquid limits; thus, the optimum amount of clay that should be added as a binder is 15%, which results in better burning and heat holding capacity and better heating time. The developed briquetting machine has a capacity of producing 60 Kg/hr but the carbonization kiln can only carbonize 3.1 Kg in 2 : 40 hours; hence, it is a bottle neck for the briquette production. The hydrocarbon laboratory analysis showed that the calorific value of the charcoal produced with 15% clay content is 4647.75 Cal/gm and decreases as clay ratio increases and is found to be sufficient energy content for cooking.

  9. Hypothalamic-pituitary vascularization in pituitary stalk transection syndrome: is the pituitary stalk really transected? The role of gadolinium-DTPA with spin-echo T1 imaging and turbo-FLASH technique

    International Nuclear Information System (INIS)

    Genovese, E.; Maghnie, M.; Beluffi, G.; Villa, A.; Sammarchi, L.; Severi, F.; Campani, R.

    1997-01-01

    We examined 14 patients, aged 10-25 years, with idiopathic hypopituitarism. All presented an ectopic posterior pituitary at the median eminence with a hypoplastic anterior pituitary on magnetic resonance imaging (MRI). Eight patients had isolated growth hormone deficit (IGHD) and six had multiple hormone deficits (MPHD). Unenhanced MRI showed the pituitary stalk, which was extremely thin, in only three patients, while T1-weighted images obtained after intravenous injection of gadopentetate dimeglumine (Gd-DTPA) showed a thin pituitary stalk in seven patients (six with IGHD and one with MPHD), demonstrating a preserved vascular component of the stalk. MRI with Gd-DTPA was more sensitive than unenhanced MRI in detecting the pituitary stalk in patients with hypopituitarism with an ectopic posterior pituitary: the stalk was demonstrated in 50 % of the cases (seven patients), versus 21.4 % (three patients) by unenhanced MRI. The dynamic study of the hypothalamo-hypophyseal axis performed with turbo-FLASH sequences after bolus injection of Gd-DTPA showed the residual anterior pituitary to have arterial enhancement times, which suggests that an arterial system compensates for the absent or diminished blood supply from the portal system, independent of stalk detection. (orig.). With 5 figs., 1 tab

  10. Hypothalamic-pituitary vascularization in pituitary stalk transection syndrome: is the pituitary stalk really transected? The role of gadolinium-DTPA with spin-echo T1 imaging and turbo-FLASH technique

    Energy Technology Data Exchange (ETDEWEB)

    Genovese, E. [Dept. of Radiology, IRCCS Policlinico S. Matteo, Pavia (Italy); Maghnie, M. [Dept. of Pediatrics, Univ. of Pavia (Italy); Beluffi, G. [Dept. of Radiodiagnosis, Section of Pediatric Radiology, IRCCS Policlinico S. Matteo, Pavia (Italy); Villa, A. [Dept. of Radiology, IRCCS Policlinico S. Matteo, Pavia (Italy); Sammarchi, L. [Dept. of Radiology, IRCCS Policlinico S. Matteo, Pavia (Italy); Severi, F. [Dept. of Pediatrics, Univ. of Pavia (Italy); Campani, R. [Dept. of Radiology, IRCCS Policlinico S. Matteo, Pavia (Italy)

    1997-01-01

    We examined 14 patients, aged 10-25 years, with idiopathic hypopituitarism. All presented an ectopic posterior pituitary at the median eminence with a hypoplastic anterior pituitary on magnetic resonance imaging (MRI). Eight patients had isolated growth hormone deficit (IGHD) and six had multiple hormone deficits (MPHD). Unenhanced MRI showed the pituitary stalk, which was extremely thin, in only three patients, while T1-weighted images obtained after intravenous injection of gadopentetate dimeglumine (Gd-DTPA) showed a thin pituitary stalk in seven patients (six with IGHD and one with MPHD), demonstrating a preserved vascular component of the stalk. MRI with Gd-DTPA was more sensitive than unenhanced MRI in detecting the pituitary stalk in patients with hypopituitarism with an ectopic posterior pituitary: the stalk was demonstrated in 50 % of the cases (seven patients), versus 21.4 % (three patients) by unenhanced MRI. The dynamic study of the hypothalamo-hypophyseal axis performed with turbo-FLASH sequences after bolus injection of Gd-DTPA showed the residual anterior pituitary to have arterial enhancement times, which suggests that an arterial system compensates for the absent or diminished blood supply from the portal system, independent of stalk detection. (orig.). With 5 figs., 1 tab.

  11. The Intersection of Stalking and the Severity of Intimate Partner Abuse.

    Science.gov (United States)

    Brady, Patrick Q; Hayes, Brittany E

    2018-04-01

    Using data from the Chicago Women's Health Risk Study (N = 464), this study examined the intersection of stalking and the severity of intimate partner abuse while controlling for previously identified risk factors of intimate partner homicide. Findings indicate that (a) victims of life-threatening abuse by an intimate partner were significantly more likely to experience stalking than victims of nonlethal abuse; (b) after controlling for key risk factors, stalking increased the risk of life-threatening abuse; and (c) threats to kill the victim if she left was the only significant stalking-related behavior that increased the risk for life-threatening abuse. In addition, an offender's prior record and a higher number of previous abusive incidents increased the risk of life-threatening abuse. Implications for prevention and future directions for research are discussed.

  12. Pituitary stalk craniopharyngioma

    Science.gov (United States)

    Figueiredo, Eberval Gadelha; Welling, Leonardo Christiaan; de Faria, Jose Weber Vieira; Teixeira, Manoel Jacobsen

    2011-01-01

    Craniopharyngiomas are benign but aggressive neoplasms arising along the craniopharyngeal duct. It is frequently located in the suprasellar region. Primarily pituitary stalk craniopharyngioma is unusual and uncommonly early diagnosed, before it enlarges and extends to supra or parasselar region. This unusual location and the small size pose therapeutic dilemmas, since it has the ability to grow larger. Currently, no consensus exists regarding the optimal management. The authors have recommended complete resection. PMID:22715220

  13. Modelling of volumetric composition and mechanical properties of unidirectional hemp/epoxy composites - Effect of enzymatic fibre treatment

    DEFF Research Database (Denmark)

    Liu, Ming; Thygesen, Anders; Meyer, Anne S.

    2016-01-01

    The objective of the present study is to assess the effect of enzymatic fibre treatments on the fibre performance in unidirectional hemp/epoxy composites by modelling the volumetric composition and mechanical properties of the composites. It is shown that the applied models can well predict...... the changes in volumetric composition and mechanical properties of the composites when differently treated hemp fibres are used. The decrease in the fibre correlated porosity factor with the enzymatic fibre treatments shows that the removal of pectin by pectinolytic enzymes results in a better fibre...

  14. Discovery of dense aggregations of stalked crinoids in Izu-Ogasawara trench, Japan.

    Science.gov (United States)

    Oji, Tatsuo; Ogawa, Yujiro; Hunter, Aaron W; Kitazawa, Kota

    2009-06-01

    Stalked crinoids are recognized as living fossils that typically inhabit modern deep-water environments exceeding 100 m. Previous records of stalked crinoids from hadal depths (exceeding 6000 m) are extremely rare, and no in-situ information has been available. We show here that stalked crinoids live densely on rocky substrates at depths over 9000 m in the Izu-Ogasawara Trench off the eastern coast of Japan, evidenced by underwater photos and videos taken by a remotely operated vehicle. This is the deepest in-situ observation of stalked crinoids and demonstrates that crinoid meadows can exist at hadal depths close to the deepest ocean floor, in a fashion quite similar to populations observed in shallower depths.

  15. Enzymatic saccharification of high pressure assist-alkali pretreated cotton stalk and structural characterization.

    Science.gov (United States)

    Du, Shuang-kui; Su, Xia; Yang, Weihua; Wang, Yanqin; Kuang, Meng; Ma, Lei; Fang, Dan; Zhou, Dayun

    2016-04-20

    Cotton stalk is a potential biomass for bioethanol production, while the conversion of direct saccharification or biotransformation of cotton stalk is extremely low due to the recalcitrant nature of lignocellulose. To enhance the enzymatic conversion of cotton stalks, the enzymatic saccharification parameters of high pressure assist-alkali pretreatment (HPAP) cotton stalk were optimized in the present study. Results indicated that a maximum reducing sugar yield of 54.7g/100g dry biomass cellulose was achieved at a substrate concentration of 2%, 100rpm agitation, 0.6g/g enzyme loading, 40°C hydrolysis temperature, 50h saccharification time, and pH 5.0. Scanning electron microscopy, X-ray diffraction, and Fourier transform infrared spectroscopy were used to identify structural changes in native, pretreated biomass and hydrolyzed residues. Structural analysis revealed large part of amorphous cellulose and partial crystalline cellulose in the HPAP cotton stalk were hydrolyzed during enzymatic treatment. HPAP cotton stalk can be used as a potential feed stock for bioethanol production. Copyright © 2015 Elsevier Ltd. All rights reserved.

  16. Two unusual causes of pituitary stalk thickening in children without clinical features of diabetes insipidus

    International Nuclear Information System (INIS)

    Andronikou, Savvas; Furlan, Gisella; Fieggen, Anthony G.; Wilmshurst, Jo

    2003-01-01

    Pituitary stalk thickening has a wide differential diagnosis, but almost all infundibular diseases present with diabetes insipidus (DI). We present a child with metastatic involvement of the pituitary stalk from a primary pontine tumour and a child with tuberculous infiltration of the pituitary stalk and associated meningeal inflammation. Neither child presented with DI. Even though both metastatic disease and tuberculous infiltration of the stalk have been reported in adults, these are the first reports with accompanying cross-sectional images of pituitary stalk involvement by these diseases in children. (orig.)

  17. Two unusual causes of pituitary stalk thickening in children without clinical features of diabetes insipidus

    Energy Technology Data Exchange (ETDEWEB)

    Andronikou, Savvas; Furlan, Gisella; Fieggen, Anthony G.; Wilmshurst, Jo [Department of Paediatric Neuroradiology, University of Cape Town, Klipfontein Road, 7700, Rondebosch, Cape Town (South Africa); Cross War Memorial Children' s Hospital, University of Cape Town, Klipfontein Road, 7700, Rondebosch, Cape Town (South Africa); School of Child and Adolescent Health, University of Cape Town, Klipfontein Road, 7700, Rondebosch, Cape Town (South Africa)

    2003-07-01

    Pituitary stalk thickening has a wide differential diagnosis, but almost all infundibular diseases present with diabetes insipidus (DI). We present a child with metastatic involvement of the pituitary stalk from a primary pontine tumour and a child with tuberculous infiltration of the pituitary stalk and associated meningeal inflammation. Neither child presented with DI. Even though both metastatic disease and tuberculous infiltration of the stalk have been reported in adults, these are the first reports with accompanying cross-sectional images of pituitary stalk involvement by these diseases in children. (orig.)

  18. Hormonal regulation of the growth of leaves and inflorescence stalk in Muscari armeniacum Leichtl.

    Directory of Open Access Journals (Sweden)

    Marian Saniewski

    2016-04-01

    Full Text Available It is known that chilling of Muscari bulbs is necessary for the growth of the inflorescence stalk and flowering, but not for the growth of leaves. Gibberellic acid (GA accelerated stem growth and flowering in chilled Muscari bulbs. In the present experiment it was shown that in unchilled derooted Muscari bulbs the growth of leaves, but not the growth of the inflorescence stalk, was observed when bulbs were stored in water, GA at a concentration of 50 and 100 mg/L, benzyladenine (BA at a concentration of 25 and 50 mg/L, or a mixture of GA+BA (50+25 mg/L, but abscisic acid (ABA at a concentration of 10 mg/L greatly inhibited the growth of leaves. In chilled derooted Muscari bulbs the growth of leaves and inflorescence stalk was observed when bulbs were stored in water or GA, but BA and GA+BA treatments totally inhibited the growth of the inflorescence stalk without an effect on the growth of leaves. These results clearly showed that the growth of leaves and inflorescence stalk in Muscari bulbs are controlled by plant growth regulators in different ways. ABA totally inhibited the growth of leaves and inflorescence stalk in chilled derooted Muscari bulbs. It was shown that after the excision of the inflorescence bud in cultivated chilled Muscari bulbs, the inflorescence stalk died, but application of indole-3-acetic acid (IAA 0.5% in the place of the removed inflorescence bud induced the growth of the inflorescence stalk. IAA applied under the inflorescence bud inhibited the development of flowers (flower-bud blasting and induced the growth of the inflorescence stalk below the treatment site. These results are discussed with reference to hormonal regulation of stem (stalk growth in tulip, narcissus, hyacinth, and Hippeastrum.

  19. Effect of metal ions on the enzymatic hydrolysis of hemp seed oil by lipase Candida sp. 99-125.

    Science.gov (United States)

    Lu, Jike; Wang, Pei; Ke, Zhaodi; Liu, Xin; Kang, Qiaozhen; Hao, Limin

    2018-07-15

    In order to study the effect of metal ions on the enzymatic hydrolysis of hemp seed oil by Candida sp. 99-125, the spectroscopy, stability and hydrolytic activity of the biocatalyst were investigated in presence of Ca 2+ , Mg 2+ , Fe 2+ , Fe 3+ , Cu 2+ , Sn 2+ , Pb 2+ , Zn 2+ and Ba 2+ metal ions, respectively. The UV spectroscopy showed that all the metal ions enhanced the absorbance but the decrease of fluorescence intensity was observed. All the metal ions could improve the lipase thermal stability except Cu 2+ and Ba 2+ . Hydrolysis of hemp seed oil proved that Ca 2+ , Fe 3+ , Pb 2+ and Ba 2+ could significantly improve the hydrolytic rate, and metal ions could influence lipase selectivity. The study revealed that metal ions could improve lipase stability, hydrolysis activity in the hydrolytic process of hemp seed oil by Candida sp. 99-125. Copyright © 2018 Elsevier B.V. All rights reserved.

  20. Body Stalk Anomaly in a 9-Week Pregnancy

    Directory of Open Access Journals (Sweden)

    Fabio E. Quijano

    2014-01-01

    Full Text Available Body stalk anomaly is a rare and severe malformation syndrome in which the exact pathophysiology and trigger factors are still unknown. This is a case of a 30-year-old patient who underwent ultrasound at 9 weeks of gestation. It revealed an abnormal location of the inferior body of the embryo in the coelomic space. The findings suggested a short umbilical cord syndrome. In order to confirm the diagnosis, the patient was scheduled for a second ultrasonography at 11 weeks of gestation. The obtained images, confirmed the location of the inferior body in the coelomic space with no visible bladder, absence of the right leg, severe abdominal wall defect, consistent with an omphalocele, and a short 5 mm umbilical cord. These last ultrasonographic findings were consistent with body stalk anomaly. Because of severe malformation incompatible with life, the patient was offered termination of pregnancy. Pathologic examination confirmed the suspected pathology of body stalk anomaly.

  1. The Power Supply And Control Unit For The HEMP Thruster

    Science.gov (United States)

    Brag, Rafael; Lenz, Werner; Huther, Andreas; Herty, Frank

    2011-10-01

    In the recent years, Astrium GmbH started to develop electronics to control and supply Electric Propulsion systems or corresponding components. One of the developments is a Power Supply and Control Unit (PSCU) for the Thales Electron Devices development "High Efficiency Multistage Plasma Thruster" (HEMP- T). The PSCU is developed, manufactured and tested on the Astrium southern Germany site in Friedrichshafen. The first application is the SGEO Satellite (HISPASAT- 1), where the In-Orbit Demonstration (IOD) of the HEMP Thruster system will prove the success of the product. Astrium conducted several coupling tests during the PSCU development especially concentrated on *Thruster electrical I/F parameters *Neutralizer electrical I/F parameters *Flow Control I/F parameters Results of these tests were used to refine the specification and adapt the PSCU drivers and control algorithms. Furthermore, the tests results gave Thales and Astrium the possibility for a deep understanding of the interaction between the physics and the electronics. The paper presents an overview of the PSCU topology, key features, technical and development logic details as well as a view into the control capabilities of the PSCU.

  2. Experimental co-digestion of corn stalk and vermicompost to improve biogas production

    International Nuclear Information System (INIS)

    Chen Guangyin; Zheng Zheng; Yang Shiguan; Fang Caixia; Zou Xingxing; Luo Yan

    2010-01-01

    Anaerobic co-digestion of corn stalk and vermicompost (VC) as well as mono-digestion of corn stalk were investigated. Batch mono-digestion experiments were performed at 35 ± 1 o C and initial total solid loading (TSL) ranged from 1.2% to 6.0%. Batch co-digestion experiments were performed at 35 ± 1 o C and initial TSL of 6% with VC proportions ranged from 20% to 80% of total solid (TS). For mono-digestion of corn stalk, a maximum methane yield of 217.60 ± 13.87 mL/g TS added was obtained at initial TSL of 4.8%, and acidification was found at initial TSL of 6.0% with the lowest pH value of 5.10 on day 4. Co-digestion improved the methane yields by 4.42-58.61% via enhancing volatile fatty acids (VFAs) concentration and pH value compared with mono-digestion of corn stalk. The maximum biogas yield of 410.30 ± 11.01 mL/g TS added and methane yield of 259.35 ± 13.85 mL/g TS added were obtained for 40% VC addition. Structure analysis by X-ray diffractometry (XRD) showed that the lowest crystallinity of 35.04 of digested corn stalk was obtained from co-digestion with 40% VC, which decreased 29.4% compared to 49.6 obtained from un-treated corn stalk. It is concluded that co-digestion with VC is beneficial for improving biodigestibility and methane yield from corn stalk.

  3. Victims of stalking in India: A study of girl college students in Tirunelveli City

    Directory of Open Access Journals (Sweden)

    Jaishankar Karuppannan

    2007-01-01

    Full Text Available The word 'stalking' was not commonly known in India, until Priyadharshini Mattoo's case (1996 hit the headlines. Eve teasing, a colloquial word for gender harassment is popularly known and Tamil Nadu Prohibition of Eve-Teasing Act, 1998 on that was developed after the brutal killing of a girl named Sarika Shah in Chennai. Though, stalking is there in the past, it was not acknowledged with this terminology and it was always merged with Eve teasing. On the other hand, stalking is much graver than Eve teasing and it is an obsessive behaviour. After the Matoo's case, the Indian Criminal Justice System awoke and the National Commission for Women is ready with a draft Bill (Sexual Assault Prevention Bill to make the Indian Penal Code more effective against the menace of stalkers. Research studies related to stalking in India are sparse and there is a need to study this phenomenon in depth. This paper presents some results from a study of stalking victims among Girl College students at Tirunelveli City, Tamil Nadu, India. In-depth questionnaire data are drawn on to investigate the course and nature of prolonged stalking in 150 self-defined victims. Findings indicate a pattern of repeated intrusions, the stalking harassment methods, lack of reporting behaviour, and effects of stalking on the victims.

  4. Predicting the long-term durability of hemp-lime renders in inland and coastal areas using Mediterranean, Tropical and Semi-arid climatic simulations.

    Science.gov (United States)

    Arizzi, Anna; Viles, Heather; Martín-Sanchez, Inés; Cultrone, Giuseppe

    2016-01-15

    Hemp-based composites are eco-friendly building materials as they improve energy efficiency in buildings and entail low waste production and pollutant emissions during their manufacturing process. Nevertheless, the organic nature of hemp enhances the bio-receptivity of the material, with likely negative consequences for its long-term performance in the building. The main purpose of this study was to study the response at macro- and micro-scale of hemp-lime renders subjected to weathering simulations in an environmental cabinet (one year was condensed in twelve days), so as to predict their long-term durability in coastal and inland areas with Mediterranean, Tropical and Semi-arid climates, also in relation with the lime type used. The simulated climatic conditions caused almost unnoticeable mass, volume and colour changes in hemp-lime renders. No efflorescence or physical breakdown was detected in samples subjected to NaCl, because the salt mainly precipitates on the surface of samples and is washed away by the rain. Although there was no visible microbial colonisation, alkaliphilic fungi (mainly Penicillium and Aspergillus) and bacteria (mainly Bacillus and Micrococcus) were isolated in all samples. Microbial growth and diversification were higher under Tropical climate, due to heavier rainfall. The influence of the bacterial activity on the hardening of samples has also been discussed here and related with the formation and stabilisation of vaterite in hemp-lime mixes. This study has demonstrated that hemp-lime renders show good durability towards a wide range of environmental conditions and factors. However, it might be useful to take some specific preventive and maintenance measures to reduce the bio-receptivity of this material, thus ensuring a longer durability on site. Copyright © 2015 Elsevier B.V. All rights reserved.

  5. Evaluation of mechanical properties of hybrid fiber (hemp, jute, kevlar) reinforced composites

    Science.gov (United States)

    Suresha, K. V.; Shivanand, H. K.; Amith, A.; Vidyasagar, H. N.

    2018-04-01

    In today's world composites play wide role in all the engineering fields. The reinforcement of composites decides the properties of the material. Natural fiber composites compared to synthetic fiber possesses poor mechanical properties. The solution for this problem is to use combination of natural fiber and synthetic fiber. Hybridization helps to improve the overall mechanical properties of the material. In this study, hybrid reinforced composites of Hemp fabric/Kevlar fabric/Epoxy and Jute fabric/ Kevlar fabric/Epoxy composites are fabricated using Simple hand layup technique followed by Vacuum bagging process. Appropriate test methods as per standards and guidelines are followed to analyze mechanical behavior of the composites. The mechanical characteristics like tensile, compression and flexural properties of the hybrid reinforced composites are tested as per the ASTM standards by series of tensile test; compression test and three point bending tests were conducted on the hybrid composites. A quantitative relationship between the Hemp fabric/Kevlar fabric/Epoxy and Jute/ Kevlar fabric/Epoxy has been established with constant thickness.

  6. Treatment of some Textile Industrial Effluents using Dry Corn Stalk ...

    African Journals Online (AJOL)

    Corn stalk ground to various mesh sizes was used to treat textile effluents obtained from three different industries. These effluents were first pretreated with alum and then charcoal; passing the water through a column, (20cm long and 5cm diameter) containing the ground corn stalk of size diameters of 300mm, 355mm ...

  7. Anaerobic digestion of industrial hemp-effect of harvest time on methane energy yield per hectare

    Energy Technology Data Exchange (ETDEWEB)

    Kreuger, E; Escobar, F; Bjoernsson, L [Department of Biotechnology, Lund University, P.O. Box 124, SE-221 00 Lund (Sweden); Prade, T; Svensson, S -E; Englund, J -E [Department of Agriculture-Farming Systems, Technology and Product Quality, Swedish University of Agricultural Sciences, P.O. Box 104, SE-230 53 Alnarp (Sweden)

    2011-02-15

    There is a worldwide emphasis to increase the share of renewable transportation fuels. When using agricultural land for production of renewable transportation fuels, the energy output per hectare for different crops and transportation fuels is a crucial factor. In this study, the gross methane energy yield per hectare from anaerobic digestion of industrial hemp (Cannabis sativa L.), was determined at four different harvest times between July and October in Southern Sweden, a cold climate region. The biomass yield was determined for three years and the methane yield was determined for two years through the biochemical methane potential test. The highest biomass yield, 16 tonnes dry matter per hectare on an average, and the highest methane energy yield per hectare was achieved when the hemp was harvested in September or October, with an average gross methane energy yield of 136 {+-} 24 GJ per hectare. There was no significant difference in the specific methane yield between the harvest times; the average being 234 {+-} 35 m{sup 3} per tonne volatile solids. Biogas from hemp turned out to be a high yielding alternative to the currently dominating renewable transportation fuels produced from crops grown in Sweden: ethanol from wheat and biodiesel from rapeseed. (author)

  8. The Reliability and Predictive Validity of the Stalking Risk Profile.

    Science.gov (United States)

    McEwan, Troy E; Shea, Daniel E; Daffern, Michael; MacKenzie, Rachel D; Ogloff, James R P; Mullen, Paul E

    2018-03-01

    This study assessed the reliability and validity of the Stalking Risk Profile (SRP), a structured measure for assessing stalking risks. The SRP was administered at the point of assessment or retrospectively from file review for 241 adult stalkers (91% male) referred to a community-based forensic mental health service. Interrater reliability was high for stalker type, and moderate-to-substantial for risk judgments and domain scores. Evidence for predictive validity and discrimination between stalking recidivists and nonrecidivists for risk judgments depended on follow-up duration. Discrimination was moderate (area under the curve = 0.66-0.68) and positive and negative predictive values good over the full follow-up period ( Mdn = 170.43 weeks). At 6 months, discrimination was better than chance only for judgments related to stalking of new victims (area under the curve = 0.75); however, high-risk stalkers still reoffended against their original victim(s) 2 to 4 times as often as low-risk stalkers. Implications for the clinical utility and refinement of the SRP are discussed.

  9. Analysis of cannabinoids in commercial hemp seed oil and decarboxylation kinetics studies of cannabidiolic acid (CBDA).

    Science.gov (United States)

    Citti, Cinzia; Pacchetti, Barbara; Vandelli, Maria Angela; Forni, Flavio; Cannazza, Giuseppe

    2018-02-05

    Hemp seed oil from Cannabis sativa L. is a very rich natural source of important nutrients, not only polyunsaturated fatty acids and proteins, but also terpenes and cannabinoids, which contribute to the overall beneficial effects of the oil. Hence, it is important to have an analytical method for the determination of these components in commercial samples. At the same time, it is also important to assess the safety of the product in terms of amount of any psychoactive cannabinoid present therein. This work presents the development and validation of a highly sensitive, selective and rapid HPLC-UV method for the qualitative and quantitative determination of the main cannabinoids, namely cannabidiolic acid (CBDA), tetrahydrocannabinolic acid (THCA), cannabidiol (CBD), tetrahydrocannabinol (THC), cannabinol (CBN), cannabigerol (CBG) and cannabidivarin (CBDV), present in 13 commercial hemp seed oils. Moreover, since decomposition of cannabinoid acids generally occurs with light, air and heat, decarboxylation studies of the most abundant acid (CBDA) were carried out in both open and closed reactor and the kinetics parameters were evaluated at different temperatures in order to evaluate the stability of hemp seed oil in different storage conditions. Copyright © 2017 Elsevier B.V. All rights reserved.

  10. Nitrogen accumulation and release by sunn hemp, calopo, mucana and devil bean in semi-arid Ghana

    International Nuclear Information System (INIS)

    Fosu, Mathias

    2003-01-01

    Four leguminous cover crops, Calopogonium mucunoides (calopo), Mucuna prupriens (mucuna), Crotalaria juncea (sunn hemp) and Crotalaria retusa (devil bean) were evaluated on the field in Northern Ghana for N 2 fixation capacity and N release. The proportion on N derived from the atmosphere (% Ndfa) by the cover crops ranged from 64.7 to 81% with mucuna giving the highest % Ndfa and calopo the least. The total N 2 fixed ranged from 59 to 109.5 kg ha 4 with devil bean giving the largest and the least from calopo. The dry matter yield of cover crops was positively correlated with the amount of N 2 , fixed but not with the percent of N derived from the atmosphere (%Ndfa). Sunn hemp, which had the best residue quality (least per cent cellulose, lignin, C N ratio and Lignin N ratio), released 50% of its N within the first two weeks while the other cover crops with relatively poor residue quality released 25% of their N within the same period. By the end of the rainy season sunn hemp had released 90% of the residue N while the other cover crops had released 80%. (author)

  11. Effect of water absorption on mechanical properties of hemp fibre/polyolefin’s composites

    CSIR Research Space (South Africa)

    Guduri, BBR

    2007-12-01

    Full Text Available malamaleated polypropylene and polyethylene were used. The tensile, flexural and impact properties of hemp fibre/polyolefin’s (PP & HDPE) composite specimens were found to increased with compatibilizer. The dry and water immersion specimens of the PP composites...

  12. The effect of Cerasus avium stalk extract on albumin glycation reaction

    Directory of Open Access Journals (Sweden)

    Mohadeseh Abdoli

    2014-10-01

    Full Text Available Background: Non-enzymatic glycosylation of proteins is the major cause of diabetic complications. The inhibition of glycation process can reduce complications of diabetes. In the Iranian traditional medicine, the decoction (boiled extraction of Cerasus avium stalk is used as a hypoglycemic agent. The aim of this study was to investigate the in vitro inhibitory effects of decoction and ethanolic and aqueous extracts of Cerasus avium stalk on albumin glycation reaction. Methods: In this experimental study, first, the ethanolic, aqueous and decoction extracts of Cerasus avium stalk were prepared. Then, different concentrations of these extracts were prepared and added to albumin and glucose solutions. Finally, compared to control group that was not treated with any extracts, the albumin glycation rate in the groups treated with various concentrations of extracts was evaluated using TBA (thio-barbituric acid method. Results: The results showed that compared to control group, decoction of Cerasus avium stalk in the concentrations of 20, 10 and 2 mg/dl could reduce albumin glycation to 85.10±1.55, 72.35±1.75 and 51.25±1.22 %, respectively (P>0.001. Moreover, in the concentration of 20 mg/dl, the inhibitory effect of decoction of Cerasus avium stalk on the albumin glycation reaction was higher than those of aqueous (P=0.021 and ethanolic (P=0.009 extracts. Conclusion: The findings showed that the extracs of Cerasus avium stalk, in particular in the decoction form, could significantly reduce the rate of albumin glycation; therefore, it can be used for decreasing diabetes mellitus complications.

  13. The Fiber Content in Fibrous Hemp Depending on Selected Agrotechnical Factors

    Directory of Open Access Journals (Sweden)

    Kryszak N.

    2016-06-01

    Full Text Available Relationship between genotypes represented by two fibrous hemp varieties and some agrotechnical factors was investigated in the study. The aim of it was finding how selected factors (three sowing dates, two sowing densities and five harvest dates influence on total fiber content using osmotic degumming of fibrous plants method for fiber content determination.

  14. Shift of the pituitary stalk in intrasellar pituitary adenomas

    International Nuclear Information System (INIS)

    Ito, Jusuke; Tokiguchi, Susumu; Nakamori, Akitoshi; Watanabe, Akira; Yokoyama, Motoharu.

    1982-01-01

    Fifty-one patients from a group of 344 patients undergoing the evaluation of intrasellar or parasellar tumors were diagnosed on CT as having an intrasellar pituitary adenoma. Axial transverse sections were performed at -10 0 to Reid's basal line, using 1.5-mm-thick slices and sagittal and coronal reformation. Of these 51 patients, 17 showed a shift of the pituitary stalk. The area where a tumor was thought to be located within the sella turcica on preoperative CT became defective on CT after transsphenoidal surgery in all cases. Histological verification was obtained in all cases. Also, the shift of the pituitary stalk was normalized or markedly improved after surgery in all cases. In functioning tumors, all cases except two showed an endocrinologically normal state or a marked improvement after transsphenoidal surgery. On the basis of the above-mentioned facts, it was concluded that the shift of the pituitary stalk in intrasellar pituitary adenomas indicated the evidence of a mass and its location in the sella turcica. However, a shift of the pituitary stalk was also observed under other conditions, such as empty sella and tuberculum sellae meningioma, and so it is not a pathognomonic finding in intrasellar pituitary adenomas. (author)

  15. Stalk-dependent and Stalk-independent Signaling by the Adhesion G Protein-coupled Receptors GPR56 (ADGRG1) and BAI1 (ADGRB1).

    Science.gov (United States)

    Kishore, Ayush; Purcell, Ryan H; Nassiri-Toosi, Zahra; Hall, Randy A

    2016-02-12

    The adhesion G protein-coupled receptors (aGPCRs) are a large yet poorly understood family of seven-transmembrane proteins. A defining characteristic of the aGPCR family is the conserved GAIN domain, which has autoproteolytic activity and can cleave the receptors near the first transmembrane domain. Several aGPCRs, including ADGRB1 (BAI1 or B1) and ADGRG1 (GPR56 or G1), have been found to exhibit significantly increased constitutive activity when truncated to mimic GAIN domain cleavage (ΔNT). Recent reports have suggested that the new N-terminal stalk, which is revealed by GAIN domain cleavage, can directly activate aGPCRs as a tethered agonist. We tested this hypothesis in studies on two distinct aGPCRs, B1 and G1, by engineering mutant receptors lacking the entire NT including the stalk (B1- and G1-SL, with "SL" indicating "stalkless"). These receptors were evaluated in a battery of signaling assays and compared with full-length wild-type and cleavage-mimicking (ΔNT) forms of the two receptors. We found that B1-SL, in multiple assays, exhibited robust signaling activity, suggesting that the membrane-proximal stalk region is not necessary for its activation. For G1, however, the results were mixed, with the SL mutant exhibiting robust activity in several signaling assays (including TGFα shedding, activation of NFAT luciferase, and β-arrestin recruitment) but reduced activity relative to ΔNT in a distinct assay (activation of SRF luciferase). These data support a model in which the activation of certain pathways downstream of aGPCRs is stalk-dependent, whereas signaling to other pathways is stalk-independent. © 2016 by The American Society for Biochemistry and Molecular Biology, Inc.

  16. Contribution to the discussion on the criminalization of stalking

    Directory of Open Access Journals (Sweden)

    Miladinović-Stefanović Dušica

    2016-01-01

    Full Text Available The serious and complex nature of stalking, as a social phenomenon, is reflected in diverse forms of this illicit act, the severity of consequences caused by its commission, and the likelihood of being turned into violence. Whereas it may be observed from different perspectives, in this paper stalking is examined from the aspect of substantive criminal law. In the first part of this article, the author provides an overview of legal provisions on the crime of stalking as envisaged in selected European legislations. In the second part of the paper, the author re-examines the capacity of the existing Serbian criminal legislation to respond to this problem, especially through the envisaged criminal offence of endangering safety of another. In conclusion, the author discusses the inadequacy of the existing legislation and the need for further legislative intervention in this area.

  17. Psychological Impact of Stalking on Male and Female Health Care Professional Victims of Stalking and Domestic Violence

    Directory of Open Access Journals (Sweden)

    Daniela Acquadro Maran

    2018-03-01

    Full Text Available The aim of this work was to investigate stalking experiences in a sample of Health Care Professionals, or HCPs, who experienced domestic violence in their previous relationships with an intimate romantic or non-romantic who had become their stalkers. A comparison between males and females was made to highlight the differences among the genders. The findings showed that, for the most part, the victims experienced stalking by a stalker that was not of the same gender. Moreover, the nature of the relationship was romantic, for the most part, for both female and male subjects, suggesting that the principal motivation of stalking is the disruption of an intimate relationship. Regarding domestic violence, females described the phenomenon from a different perspective, indicating verbal, physical, and sexual abuse, while males indicated only verbal abuse. Females tended to amplify, more than the males, depression, and state and trait anxiety. Even if all symptoms were expressed in both females and males, the males exhibited a lack of confidence in their bodies, and the emotional literacy made the expression of distress more difficult. At the same time, the expression of anxiety presented in the women permitted them to become progressively less victimized over time; depression and anxiety allow the recognition of these symptoms as signs of distress and to intervene to reduce them.

  18. Psychological Impact of Stalking on Male and Female Health Care Professional Victims of Stalking and Domestic Violence.

    Science.gov (United States)

    Acquadro Maran, Daniela; Varetto, Antonella

    2018-01-01

    The aim of this work was to investigate stalking experiences in a sample of Health Care Professionals, or HCPs, who experienced domestic violence in their previous relationships with an intimate romantic or non-romantic who had become their stalkers. A comparison between males and females was made to highlight the differences among the genders. The findings showed that, for the most part, the victims experienced stalking by a stalker that was not of the same gender. Moreover, the nature of the relationship was romantic, for the most part, for both female and male subjects, suggesting that the principal motivation of stalking is the disruption of an intimate relationship. Regarding domestic violence, females described the phenomenon from a different perspective, indicating verbal, physical, and sexual abuse, while males indicated only verbal abuse. Females tended to amplify, more than the males, depression, and state and trait anxiety. Even if all symptoms were expressed in both females and males, the males exhibited a lack of confidence in their bodies, and the emotional literacy made the expression of distress more difficult. At the same time, the expression of anxiety presented in the women permitted them to become progressively less victimized over time; depression and anxiety allow the recognition of these symptoms as signs of distress and to intervene to reduce them.

  19. Cultural Models Shaping Stalking From a Content Analysis of Italian Newspapers

    Directory of Open Access Journals (Sweden)

    Andrea Caputo

    2013-08-01

    Full Text Available The increasing spread of stalking in recent years has captured the community’s and media’s interest and highlighted complex legal, clinical and cultural issues. This phenomenon, far from being an individual problem, can be considered as a product of a growing culture that seems to reveal the crisis of current rules of social coexistence. This work aims at detecting the cultural repertoires that organise the stalking discourse, from an analysis of Italian newspaper articles, within a socio-constructivist paradigm. Emotional text analysis was conducted on a corpus of headlines and subheadings derived from 496 articles. These articles were published in major national newspapers and helped to identify four cultural repertoires (clusters that characterise the social representation of stalking: gender violence and women’s social independence (Cluster 1, psychological violence and control as illusion of intimacy (Cluster 2, anomic violence and intolerant individualism (Cluster 3, domestic violence and women’s marital obligation (Cluster 4. These repertoires are conceived along three latent dimensions which respectively refer to the cultural functions of stalking (Factor 1, representations of the victim (Factor 2, and gender inequalities (Factor 3. The paper offers a key to a social contextualisation of stalking in Italy, in order to re-think work practices within institutional agencies that deal with this phenomenon.

  20. Effects of thermal and enzymatic treatments and harvesting time on the microbial quality and chemical composition of fibre hemp (Cannabis sativa L.)

    Energy Technology Data Exchange (ETDEWEB)

    Nykter, Minna; Kymaelaeinen, Hanna-Riitta; Sjoeberg, Anna-Maija [Department of Agrotechnology, University of Helsinki, P.O. Box 28, FI-00014 University of Helsinki (Finland); Thomsen, Anne Belinda; Thygesen, Anders [Biosystems Department, Risoe National Laboratory, P.O. Box 49, DK-4000 Roskilde (Denmark); Lilholt, Hans [Materials Research Department, Risoe National Laboratory, P.O. Box 49, DK-4000 Roskilde (Denmark); Koponen, Hilkka [Department of Applied Biology, Section of Plant Pathology, University of Helsinki, P.O. Box 27, FI-00014 University of Helsinki (Finland)

    2008-05-15

    The aim of the present study was to examine the effects of pectinase enzyme treatment followed by thermal treatments (steam explosion and dry heating) on the microbial quality and chemical composition of hemp fibres. Before these treatments, the fibres were separated manually from the stems harvested after stand retting in the field before frost, after early frost or in the following spring. The enzymatic treatment of hemp promoted growth of moulds on the fibres (500-fold increase in colony-forming units (cfu)), whereas steam explosion reduced the amount of moulds to a relatively constant level of 10{sup 2} cfu/g dw. The amount of bacteria was not markedly affected by enzymatic treatment but was reduced tenfold after steam explosion. Steam explosion is thereby a potentially good process for the production of hemp fibres with low fungal contamination, which can be of importance in insulation materials. Dry heating had no effect on mould and bacterial counts at temperatures below 120 C and durations less than 60 min. The chemical composition was affected by the enzymatic treatment due to extraction and degradation of water-soluble components, pectin and ash. Thus the cellulose content increased by 6% w/w to 67-70% w/w. Steam explosion of the untreated hemp fibres increased the cellulose content to 74% w/w, whereas steam explosion of enzymatically treated hemp increased the cellulose content to 78% w/w. (author)

  1. Lo stalking, un reato senza genere

    Directory of Open Access Journals (Sweden)

    Annamaria Iaccarino

    2015-09-01

    Full Text Available An individual who watches, follows, tracks and controls the victim with the aim of intervening, in a more or less violent way, in their private life is called a stalker or a “prowler always on the lookout”, because they commit repeated actions or attempted contacts or real communications, not desired by the victim, which may cause discomfort, anxiety, nuisance, concern and fear to the victim. Stalking is a term that may apply to any gender. To Lombroso’s “monster woman” and Hart’s “old maids’ madness” it is necessary to add the phenomenon of stalking committed by women whose modus operandi, without doubt, is more sly and subtle than the one of men. It refers to the retrospective act analysed by classic theories.

  2. Colonization of habitat islands in the deep sea: recruitment to glass sponge stalks

    Science.gov (United States)

    Beaulieu, Stace E.

    2001-04-01

    Biogenic structures in the deep sea often act as hard substratum 'islands' for the attachment of encrusting fauna. At an abyssal station in the NE Pacific, stalks of hexactinellid sponges in the genus Hyalonema are habitat islands for species-rich epifaunal communities. An experimental study was conducted to (1) determine the colonization rates of artificial Hyalonema stalks, (2) compare the species composition and diversity of recruits to newly available substrata to that of the natural communities, and (3) examine the vertical distribution of recruits. Four sets of six artificial sponge stalks, constructed of Hyalonema spicules, were deployed at 4100 m depth for 3- to 5-month periods. There was no difference in net colonization or immigration rate among the four deployments. Colonization rates were similar to those reported for other deep-sea, hard substratum recruitment experiments. The taxa that recruited to the artificial stalks were a subset of the taxa found in natural communities. However, several taxa important in structuring natural communities did not recruit to the artificial stalks. The two taxa with the highest invasion rates, a calcareous foraminiferan ( Cibicides lobatulus) and a serpulid polychaete ( Bathyvermilia sp.), also were the two taxa with greatest relative abundance in natural communities. Vertical distributions of Cibicides and an agglutinated foraminiferan ( Telammina sp.) were skewed towards the top of the artificial stalks, potentially because of active habitat selection. These results have several implications for natural Hyalonema stalk communities. Most importantly, species composition and abundance of individuals in the stalk communities appear to be maintained by frequent recruitment of a few common taxa and infrequent recruitment of many rare taxa. An argument is presented for temporal-mosaic maintenance of diversity in these deep-sea, hard substratum communities.

  3. Development of Highly Repellent Silica Particles for Protection of Hemp Shiv Used as Insulation Materials

    Directory of Open Access Journals (Sweden)

    Marion A. Bourebrab

    2017-12-01

    Full Text Available New bio-materials have recently gained interest for use in insulation panels in walls, but wider adoption by the building industry is hindered by their intrinsic properties. The fact that such materials are mainly composed of cellulose makes them combustible, and their hydrophilic surface presents a high water uptake, which would lead to faster biodegradation. A hydrophobic treatment with silica particles was successfully synthesised via Stöber process, characterised, and deposited on hemp shiv. The surface of hemp shiv coated several times with 45 and 120 nm particles were uniformly covered, as well as extensively water repellent. Those samples could withstand in humidity chamber without loss of their hydrophobic property and no sign of mould growth after 72 h of exposure.

  4. Development of Highly Repellent Silica Particles for Protection of Hemp Shiv Used as Insulation Materials.

    Science.gov (United States)

    Bourebrab, Marion A; Durand, Géraldine G; Taylor, Alan

    2017-12-21

    New bio-materials have recently gained interest for use in insulation panels in walls, but wider adoption by the building industry is hindered by their intrinsic properties. The fact that such materials are mainly composed of cellulose makes them combustible, and their hydrophilic surface presents a high water uptake, which would lead to faster biodegradation. A hydrophobic treatment with silica particles was successfully synthesised via Stöber process, characterised, and deposited on hemp shiv. The surface of hemp shiv coated several times with 45 and 120 nm particles were uniformly covered, as well as extensively water repellent. Those samples could withstand in humidity chamber without loss of their hydrophobic property and no sign of mould growth after 72 h of exposure.

  5. Accelerated aging as vigor test for sunn hemp seeds

    OpenAIRE

    Silva, Clíssia Barboza da; Barbosa, Rafael Marani; Vieira, Roberval Daiton

    2016-01-01

    ABSTRACT: This study aimed to determine the most appropriate method to assess the sunn hemp ( Crotalaria juncea L.) seed vigor in the accelerated aging test. Five seed lots from harvest 2007/2008 were evaluated for germination, vigor and seedling emergence in the field. Accelerated aging test was performed at 41°C during 48, 72 and 96 hours, with and without sodium chloride saturated solution. Then, the promising procedure was also performed for 2008/2009 and 2009/2010 harvests. In the tradit...

  6. Accelerated aging as vigor test for sunn hemp seeds

    OpenAIRE

    Silva,Clíssia Barboza da; Barbosa,Rafael Marani; Vieira,Roberval Daiton

    2017-01-01

    ABSTRACT: This study aimed to determine the most appropriate method to assess the sunn hemp ( Crotalaria juncea L.) seed vigor in the accelerated aging test. Five seed lots from harvest 2007/2008 were evaluated for germination, vigor and seedling emergence in the field. Accelerated aging test was performed at 41°C during 48, 72 and 96 hours, with and without sodium chloride saturated solution. Then, the promising procedure was also performed for 2008/2009 and 2009/2010 harvests. In the tradit...

  7. Mass transfer effect of the stalk contraction-relaxation cycle of Vorticella convallaria

    Science.gov (United States)

    Zhou, Jiazhong; Admiraal, David; Ryu, Sangjin

    2014-11-01

    Vorticella convallaria is a genus of protozoa living in freshwater. Its stalk contracts and coil pulling the cell body towards the substrate at a remarkable speed, and then relaxes to its extended state much more slowly than the contraction. However, the reason for Vorticella's stalk contraction is still unknown. It is presumed that water flow induced by the stalk contraction-relaxation cycle may augment mass transfer near the substrate. We investigated this hypothesis using an experimental model with particle tracking velocimetry and a computational fluid dynamics model. In both approaches, Vorticella was modeled as a solid sphere translating perpendicular to a solid surface in water. After having been validated by the experimental model and verified by grid convergence index test, the computational model simulated water flow during the cycle based on the measured time course of stalk length changes of Vorticella. Based on the simulated flow field, we calculated trajectories of particles near the model Vorticella, and then evaluated the mass transfer effect of Vorticella's stalk contraction based on the particles' motion. We acknowlege support from Laymann Seed Grant of the University of Nebraska-Lincoln.

  8. Sunn Hemp Biomass and Nitrogen Production for Different Planting Dates and Seeding Rates

    Science.gov (United States)

    Elevated nitrogen (N) fertilizer costs have renewed interest in alternative N sources, such as legumes. Sunn hemp (Crotalaria juncea L.) is a tropical legume capable of producing considerable biomass in a short period of time. A randomized complete block design with a split-plot restriction and fou...

  9. Lithotrophic iron-oxidizing bacteria produce organic stalks to control mineral growth: implications for biosignature formation

    Energy Technology Data Exchange (ETDEWEB)

    Chan, Clara S; Fakra, Sirine C; Emerson, David; Fleming, Emily J; Edwards, Katrina J

    2011-07-01

    Neutrophilic Fe-oxidizing bacteria (FeOB) are often identified by their distinctive morphologies, such as the extracellular twisted ribbon-like stalks formed by Gallionella ferruginea or Mariprofundus ferrooxydans. Similar filaments preserved in silica are often identified as FeOB fossils in rocks. Although it is assumed that twisted iron stalks are indicative of FeOB, the stalk's metabolic role has not been established. To this end, we studied the marine FeOB M. ferrooxydans by light, X-ray and electron microscopy. Using time-lapse light microscopy, we observed cells excreting stalks during growth (averaging 2.2 {micro}m h(-1)). Scanning transmission X-ray microscopy and near-edge X-ray absorption fine structure (NEXAFS) spectroscopy show that stalks are Fe(III)-rich, whereas cells are low in Fe. Transmission electron microscopy reveals that stalks are composed of several fibrils, which contain few-nanometer-sized iron oxyhydroxide crystals. Lepidocrocite crystals that nucleated on the fibril surface are much larger ({approx}100 nm), suggesting that mineral growth within fibrils is retarded, relative to sites surrounding fibrils. C and N 1s NEXAFS spectroscopy and fluorescence probing show that stalks primarily contain carboxyl-rich polysaccharides. On the basis of these results, we suggest a physiological model for Fe oxidation in which cells excrete oxidized Fe bound to organic polymers. These organic molecules retard mineral growth, preventing cell encrustation. This model describes an essential role for stalk formation in FeOB growth. We suggest that stalk-like morphologies observed in modern and ancient samples may be correlated confidently with the Fe-oxidizing metabolism as a robust biosignature.

  10. Effect of Mowing Cotton Stalks and Preventing Plant Re-Growth on Post-Harvest Reproduction of Meloidogyne incognita

    Science.gov (United States)

    Davis, Richard F.; Kemerait, Robert C.

    2010-01-01

    The southern root-knot nematode (Meloidogyne incognita) is a major parasite of cotton in the U.S., and management tactics for this nematode attempt to minimize population levels. We compared three post-harvest practices for their ability to reduce nematode population levels in the field, thereby reducing initial nematode population for the next year's crop. The three practices tested were: 1) chemical defoliation before harvest plus cutting cotton stalks after harvest, 2) chemical defoliation plus applying a herbicide to kill plants prior to cutting the stalks, and 3) chemical defoliation without cutting stalks. Experiments were conducted in both the greenhouse and in the field. The greenhouse experiments demonstrated that M. incognita reproduction (measured as egg counts and root gall rating indices) was significantly greater when stalks were not cut. Cutting stalks plus applying herbicide to kill cotton roots did not significantly reduce nematode reproduction compared to cutting stalks alone. In field experiments, cutting stalks reduced egg populations and root galling compared to defoliation without stalk cutting. In a greenhouse bioassay which used soil from the field plots, plants grown in soil from the defoliation only treatment had greater root gall ratings and egg counts than in the stalk cutting plus herbicide treatment. Therefore, we conclude that cutting cotton stalks immediately after harvest effectively reduces M. incognita reproduction, and may lead to a lower initial population density of this nematode in the following year. PMID:22736845

  11. Comparative environmental performance of lignocellulosic ethanol from different feedstocks

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez-Garcia, Sara; Moreira, M. Teresa; Feijoo, Gumersindo [Department of Chemical Engineering, School of Engineering, University of Santiago de Compostela, 15782 Santiago de Compostela (Spain)

    2010-09-15

    A renewable biofuel economy is projected as a pathway to decrease dependence on fossil fuels as well as to reduce greenhouse gases (GHG) emissions. Ethanol produced on large-scale from lignocellulosic raw materials is considered the most potential next generation automotive fuel. In this paper, a Life Cycle Assessment model was developed to evaluate the environmental implications of the production of ethanol from five lignocellulosic materials: alfalfa stems, poplar, Ethiopian mustard, flax shives and hemp hurds and its use in passenger cars. Two ethanol-based fuel applications, E10 (a mixture of 10% ethanol and 90% gasoline by volume) and E85 (85% ethanol and 15% gasoline by volume) were assessed and the results were compared to those of conventional gasoline (CG) in an equivalent car. The environmental performance was assessed in terms of fossil fuels requirements, global warming, photochemical oxidant formation, acidification and eutrophication by means of the Life Cycle Assessment (LCA) methodology in order to identify the best environmental friendly lignocellulosic source. The results show that, compared to CG, life cycle greenhouse gases emissions are lower for etanol blends, specifically up to 145% lower for E85-fueled car derived from Ethiopian mustard. This crop is also the best option in terms of eutrophying emissions regardless the ratio of ethanol in the blend. In the remaining impact categories, other feedstocks are considered beneficial, that is, poplar in the case of photochemical oxidants formation and flax shives for acidification. Concerning fossil fuels requirements, decreases up to 10% and 63% for E10 and E85 derived from hemp hurds and Ethiopian mustard, respectively, were obtained. According to the results, the study clearly demonstrates the importance of using low intensive energy and high biomass yield crops. LCA procedure helps to identify the key areas in the ethanol production life cycle where the researchers and technicians need to work

  12. Radiation induced pseudoisochromosomes in sunn hemp (Crotalaria juncea L.)

    International Nuclear Information System (INIS)

    Gupta, P.K.; Gupta, Rani

    1978-01-01

    In a population of sunn hemp (C. juncea), irradiated with gamma rays (30 Kr), a single plant was found to exhibit the presence of two ring univalents in 75.5% pollen mother cells. This was interpreted as a result of an interchange between the opposite arms of two homologous chromosomes giving rise to pseudoisochromosomes. In few other cells, four univalents and a single quadrivalent were also observed, thus indicating that two other interchanges involved very small segments, one of them between homologous chromosomes and the other between non-homologous chromosomes. (auth.)

  13. Radiation induced pseudoisochromosomes in sunn hemp (Crotalaria juncea L. )

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, P K; Gupta, R [Meerut Univ. (India). Inst. of Advanced Studies

    1978-01-01

    In a population of sunn hemp (C. juncea), irradiated with gamma rays (30 Kr), a single plant was found to exhibit the presence of two ring univalents in 75.5% pollen mother cells. This was interpreted as a result of an interchange between the opposite arms of two homologous chromosomes giving rise to pseudoisochromosomes. In few other cells, four univalents and a single quadrivalent were also observed, thus indicating that two other interchanges involved very small segments, one of them between homologous chromosomes and the other between non-homologous chromosomes.

  14. Effects of thermal and enzymatic treatments and harvesting time on the microbial quality and chemical composition of fibre hemp (Cannabis sativa L.)

    DEFF Research Database (Denmark)

    Nykter, M.; Kymalainen, H.R.; Thomsen, Anne Belinda

    2008-01-01

    The aim of the present study was to examine the effects of pectinase enzyme treatment followed by thermal treatments (steam explosion and dry heating) on the microbial quality and chemical composition of hemp fibres. Before these treatments, the fibres were separated manually from the stems...... materials. Dry heating had no effect on mould and bacterial counts at temperatures below 120 degrees C and durations less than 60 min. The chemical composition was affected by the enzymatic treatment due to extraction and degradation of water-soluble components, pectin and ash. Thus the cellulose content...... increased by 6% w/w to 67-70% w/w. Steam explosion of the untreated hemp fibres increased the cellulose content to 74% w/w, whereas steam explosion of enzymatically treated hemp increased the cellulose content to 78% w/w. (c) 2007 Elsevier Ltd. All rights reserved....

  15. Development of a new extraction technique and HPLC method for the analysis of non-psychoactive cannabinoids in fibre-type Cannabis sativa L. (hemp).

    Science.gov (United States)

    Brighenti, Virginia; Pellati, Federica; Steinbach, Marleen; Maran, Davide; Benvenuti, Stefania

    2017-09-05

    The present work was aimed at the development and validation of a new, efficient and reliable technique for the analysis of the main non-psychoactive cannabinoids in fibre-type Cannabis sativa L. (hemp) inflorescences belonging to different varieties. This study was designed to identify samples with a high content of bioactive compounds, with a view to underscoring the importance of quality control in derived products as well. Different extraction methods, including dynamic maceration (DM), ultrasound-assisted extraction (UAE), microwave-assisted extraction (MAE) and supercritical-fluid extraction (SFE) were applied and compared in order to obtain a high yield of the target analytes from hemp. Dynamic maceration for 45min with ethanol (EtOH) at room temperature proved to be the most suitable technique for the extraction of cannabinoids in hemp samples. The analysis of the target analytes in hemp extracts was carried out by developing a new reversed-phase high-performance liquid chromatography (HPLC) method coupled with diode array (UV/DAD) and electrospray ionization-mass spectrometry (ESI-MS) detection, by using an ion trap mass analyser. An Ascentis Express C 18 column (150mm×3.0mm I.D., 2.7μm) was selected for the HPLC analysis, with a mobile phase composed of 0.1% formic acid in both water and acetonitrile, under gradient elution. The application of the fused-core technology allowed us to obtain a significant improvement of the HPLC performance compared with that of conventional particulate stationary phases, with a shorter analysis time and a remarkable reduction of solvent usage. The analytical method optimized in this study was fully validated to show compliance with international requirements. Furthermore, it was applied to the characterization of nine hemp samples and six hemp-based pharmaceutical products. As such, it was demonstrated to be a very useful tool for the analysis of cannabinoids in both the plant material and its derivatives for

  16. Influence of Hybridizing Flax and Hemp-Agave Fibers with Glass Fiber as Reinforcement in a Polyurethane Composite

    Directory of Open Access Journals (Sweden)

    Pankaj Pandey

    2016-05-01

    Full Text Available In this study, six combinations of flax, hemp, and glass fiber were investigated for a hybrid reinforcement system in a polyurethane (PU composite. The natural fibers were combined with glass fibers in a PU composite in order to achieve a better mechanical reinforcement in the composite material. The effect of fiber hybridization in PU composites was evaluated through physical and mechanical properties such as water absorption (WA, specific gravity (SG, coefficient of linear thermal expansion (CLTE, flexural and compression properties, and hardness. The mechanical properties of hybridized samples showed mixed trends compared to the unhybridized samples, but hybridization with glass fiber reduced water absorption by 37% and 43% for flax and hemp-agave PU composites respectively.

  17. Behavioral and Mental Health Correlates of Youth Stalking Victimization: A Latent Class Approach.

    Science.gov (United States)

    Reidy, Dennis E; Smith-Darden, Joanne P; Kernsmith, Poco D

    2016-12-01

    Although recognized as a public health problem, little attention has been paid to the problem of stalking among youth. Latent profile analysis was used to identify latent groups of adolescent stalking victims and their behavioral and mental health correlates. A cross-sectional sample of 1,236 youths were randomly selected from 13 schools stratified by community risk level (i.e., low, moderate, and high risk) and gender. Students completed surveys assessing behavioral indicators of stalking victimization, as well as substance use, sexual behavior, dating violence, and psychiatric symptoms. Data were collected in 2013 and data analyses were performed in 2015. Analysis indicated the presence of a non-victim class, a minimal exposure class, and a victim class for boys and girls alike. Approximately 14% of girls and 13% of boys were in the stalking victim class. Adolescents in the victim class reported more symptoms of post-traumatic stress, mood disorder, and hopelessness, as well as more instances of alcohol use, binge drinking, and physical dating violence victimization. Girls in the victim class also reported engaging in sexting behaviors and oral sex with significantly more partners than their non-victim peers. These findings provide valuable knowledge of the prevalence and pertinent health correlates of stalking victimization in adolescence. The data suggest a substantial proportion of adolescents are victims of stalking and are likewise at risk for a number of deleterious health outcomes. As such, this population merits further attention by prevention researchers and practitioners. Published by Elsevier Inc.

  18. Effect of unconventional oilseeds (safflower, poppy, hemp, camelina) on in vitro ruminal methane production and fermentation.

    Science.gov (United States)

    Wang, Shaopu; Kreuzer, Michael; Braun, Ueli; Schwarm, Angela

    2017-08-01

    Dietary supplementation with oilseeds can reduce methane emission in ruminants, but only a few common seeds have been tested so far. This study tested safflower (Carthamus tinctorius), poppy (Papaver somniferum), hemp (Cannabis sativa), and camelina (Camelina sativa) seeds in vitro using coconut (Cocos nucifera) oil and linseed (Linum usitatissimum) as positive controls. All the tested oilseeds suppressed methane yield (mL g -1 dry matter, up to 21%) compared to the non-supplemented control when provided at 70 g oil kg -1 dry matter, and they were as effective as coconut oil. Safflower and hemp were more effective than linseed (21% and 18% vs. 10%), whereas the effects of poppy and camelina were similar to linseed. When methane was related to digestible organic matter, only hemp and safflower seeds and coconut oil were effective compared to the non-supplemented control (up to 11%). The level of methanogenesis and the ratios of either the n-6:n-3 fatty acids or C 18 :2 :C 18 :3 in the seed lipids were not related. Unconventional oilseeds widen the spectrum of oilseeds that can be used in dietary methane mitigation. In vivo confirmation of their methane mitigating effect is still needed, and their effects on animal performance still must be determined. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

  19. study on the chopping and mixing of cotton stalks with soil | Sa glam ...

    African Journals Online (AJOL)

    -type, splined-type and vertical-blade rotating dredge). Field experiments were conducted with each type to determine the proportion of non-uprooted cotton stalks; mean “post-chopping height” of the stalks, measured from soil surface; and the ...

  20. Dislocations in single hemp fibres-investigations into the relationship of structural distortions and tensile properties at the cell wall level

    DEFF Research Database (Denmark)

    Thygesen, Lisbeth Garbrecht; Eder, M.; Burgert, I.

    2007-01-01

    The relationship between dislocations and mechanical properties of single hemp fibres (Cannabis sativa L. var. Felina) was studied using a microtensile testing setup in a 2-fold approach. In a first investigation the percentage of dislocations was quantified using polarized light microscopy (PLM......) prior to microtensile testing of the fibres. In a second approach PLM was used to monitor the dislocations while straining single fibres. The first part of the study comprised 53 hemp fibres with up to 20% of their cell wall consisting of dislocations. For this data set the percentage of dislocations...

  1. ENVIRONMENTAL CONTROL OF STALK LENGTH IN THE BLOOM-FORMING, FRESHWATER BENTHIC DIATOM DIDYMOSPHENIA GEMINATA (BACILLARIOPHYCEAE)(1).

    Science.gov (United States)

    Kilroy, Cathy; Bothwell, Max

    2011-10-01

    Blooms of the freshwater stalked diatom Didymosphenia geminata (Lyngb.) M. Schmidt in A. Schmidt typically occur in oligotrophic, unshaded streams and rivers. Observations that proliferations comprise primarily stalk material composed of extracellular polymeric substances (EPS) led us to ask whether or not the production of excessive EPS is favored under nutrient-limited, high-light conditions. We conducted experiments in outdoor flumes colonized by D. geminata using water from the oligotrophic, D. geminata-affected Waitaki River, South Island, New Zealand, to determine the relationship between D. geminata stalk length, cell division rates, and light intensity under ambient and nutrient-enriched conditions. Stalk lengths were measured in situ, and cell division rates were estimated as the frequency of dividing cells (FDC). FDC responded positively to increasing light intensity and to nutrient additions (N+P and P). Under ambient conditions, stalk length increased as light level increased except at low ambient light levels and temperature. Nutrient enrichment resulted in decreased stalk length and negative correlations with FDC, with this effect most evident under high light. Our results are consistent with the hypothesis that extensive stalk production in D. geminata occurs when cell division rates are nutrient limited and light levels are high. Thus, photosynthetically driven EPS production in the form of stalks, under nutrient-limited conditions, may explain the development of very high biomass in this species in oligotrophic rivers. The responses of FDC and stalk length under nutrient-replete conditions are also consistent with occurrences of D. geminata as a nondominant component of mixed periphyton communities in high-nutrient streams. © 2011 Phycological Society of America.

  2. Continuous ethanol production using yeast immobilized on sugar-cane stalks

    Energy Technology Data Exchange (ETDEWEB)

    Vasconcelos, J.N. de [Alagoas Univ., Maceio, AL (Brazil). Dept. de Engenharia Quimica]. E-mail: jnunes@ctec.ufal.br; Lopes, C.E. [Pernambuco Univ., Recife, PE (Brazil). Dept. de Antibioticos; Franca, F.P. de [Universidade Federal, Rio de Janeiro, RJ (Brazil). Escola de Quimica. Dept. de Engenharia Bioquimica

    2004-09-01

    Sugar-cane stalks, 2.0 cm long, were used as a support for yeast immobilization envisaging ethanol production. The assays were conducted in 38.5 L fermenters containing a bed of stalks with 50% porosity. The operational stability of the immobilized yeast, the efficiency and stability of the process, as well as the best dilution rate were evaluated. Molasses from demerara sugar production was used in the medium formulation. It was diluted to obtain 111.75 {+-} 1.51 g/L without any further treatment. Sulfuric acid was used to adjust the pH value to around 4.2. Every two days Kamoran HJ (10 ppm) or with a mixture containing penicillin (10 ppm) and tetracycline (10 ppm), was added to the medium. Ethanol yield and efficiency were 29.64 g/L.h and 86.40%, respectively, and the total reducing sugars conversion was 74.61% at a dilution rate of 0.83 h{sup -1}. The yeast-stalk system was shown to be stable for over a 60 day period at extremely variable dilution rates ranging from 0.05 h{sup -1} to 3.00 h{sup -1}. The concentration of immobilized cell reached around 109 cells/gram of dry sugar-cane stalk when the fermenter was operating at the highest dilution rate (3.00 h{sup -1}). (author)

  3. Laccase enzyme detoxifies hydrolysates and improves biogas production from hemp straw and miscanthus.

    Science.gov (United States)

    Schroyen, Michel; Van Hulle, Stijn W H; Holemans, Sander; Vervaeren, Han; Raes, Katleen

    2017-11-01

    The impact of various phenolic compounds, vanillic acid, ferulic acid, p-coumaric acid and 4-hydroxybenzoic acid on anaerobic digestion of lignocellulosic biomass (hemp straw and miscanthus) was studied. Such phenolic compounds have been known to inhibit biogas production during anaerobic digestion. The different phenolic compounds were added in various concentrations: 0, 100, 500, 1000 and 2000mg/L. A difference in inhibition of biomethane production between the phenolic compounds was noted. Hydrolysis rate, during anaerobic digestion of miscanthus was inhibited up to 50% by vanillic acid, while vanillic acid had no influence on the initial rate of biogas production during the anaerobic digestion of hemp straw. Miscanthus has a higher lignin concentration (12-30g/100gDM) making it less accessible for degradation, and in combination with phenolic compounds released after harsh pretreatments, it can cause severe inhibition levels during the anaerobic digestion, lowering biogas production. To counter the inhibition, lignin degrading enzymes can be used to remove or degrade the inhibitory phenolic compounds. The interaction of laccase and versatile peroxidase individually with the different phenolic compounds was studied to have insight in the polymerization of inhibitory compounds or breakdown of lignocellulose. Hemp straw and miscanthus were incubated with 0, 100 and 500mg/L of the different phenolic compounds for 0, 6 and 24h and pretreated with the lignin degrading enzymes. A laccase pretreatment successfully detoxified the substrate, while versatile peroxidase however was inhibited by 100mg/L of each of the individual phenolic compounds. Finally a combination of enzymatic detoxification and subsequent biogas production showed that a decrease in phenolic compounds by laccase treatment can considerably lower the inhibition levels of the biogas production. Copyright © 2017 Elsevier Ltd. All rights reserved.

  4. The effect of plant population and nitrogen fertilizer on

    Directory of Open Access Journals (Sweden)

    mohamad reza asgaripor

    2009-06-01

    Full Text Available Interest has increased towards hemp (Cannabis sativa L. fibre production due to renewed demand for natural fibre in the world. A Study was conducted in 2005 at Shirvan in Northern Khorasan province, Iran, to determine the effects of three plant populations (30, 90 and 150 plant per m2 and three rates of nitrogen application (50, 150 and 250 kg N per ha on final stand, stalk height, basal stalk diameter, total stalk yield as well as fibre content from stalk and fibre yield in male and female plants. A split plot experimental with three replications was used. The result indicated that due to enhanced competition for light at higher population on density and N2 level plant mortality was higher than other treatment Morphological characteristics were highly correlated with plant sexual, plant population and nitrogen fertilizer. Highest stem, leaf and inflorescence yield were obtained at 250 plant m-2 when 150 kg N ha-1 was used. Lowest plant density did not show self-thinning but reduced above ground dry matter. Shoot dry matter increased with increasing plant density and nitrogen supply. Apparently, fibre content was greater at medium density and lowest nitrogen fertilizer, however, fibre yield was greatest at highest plant population and nitrogen fertilizer. In terms of fibre yield, approximate 31.7% of the fibre was located in the bottom parts, 22.4% in the middle and only 9.9% in the top part of the stem. The results suggest that hemp can yield large quantities of useful fibre at Shirvan when planted in proper plant densities and suitable nitrogen fertilizer.

  5. The special neuraminidase stalk-motif responsible for increased virulence and pathogenesis of H5N1 influenza A virus.

    Directory of Open Access Journals (Sweden)

    Hongbo Zhou

    Full Text Available The variation of highly pathogenic avian influenza H5N1 virus results in gradually increased virulence in poultry, and human cases continue to accumulate. The neuraminidase (NA stalk region of influenza virus varies considerably and may associate with its virulence. The NA stalk region of all N1 subtype influenza A viruses can be divided into six different stalk-motifs, H5N1/2004-like (NA-wt, WSN-like, H5N1/97-like, PR/8-like, H7N1/99-like and H5N1/96-like. The NA-wt is a special NA stalk-motif which was first observed in H5N1 influenza virus in 2000, with a 20-amino acid deletion in the 49(th to 68(th positions of the stalk region. Here we show that there is a gradual increase of the special NA stalk-motif in H5N1 isolates from 2000 to 2007, and notably, the special stalk-motif is observed in all 173 H5N1 human isolates from 2004 to 2007. The recombinant H5N1 virus with the special stalk-motif possesses the highest virulence and pathogenicity in chicken and mice, while the recombinant viruses with the other stalk-motifs display attenuated phenotype. This indicates that the special stalk-motif has contributed to the high virulence and pathogenicity of H5N1 isolates since 2000. The gradually increasing emergence of the special NA stalk-motif in H5N1 isolates, especially in human isolates, deserves attention by all.

  6. Victims of stalking in India: A study of girl college students in Tirunelveli City

    OpenAIRE

    Jaishankar Karuppannan; Kosalai Puthisigamani

    2007-01-01

    The word 'stalking' was not commonly known in India, until Priyadharshini Mattoo's case (1996) hit the headlines. Eve teasing, a colloquial word for gender harassment is popularly known and Tamil Nadu Prohibition of Eve-Teasing Act, 1998 on that was developed after the brutal killing of a girl named Sarika Shah in Chennai. Though, stalking is there in the past, it was not acknowledged with this terminology and it was always merged with Eve teasing. On the other hand, stalking is much graver t...

  7. Growth models for morphological traits of sunn hemp

    Directory of Open Access Journals (Sweden)

    Cláudia Marques de Bem

    2017-10-01

    Full Text Available The objective of the present study was to fit Gompertz and Logistic nonlinear to descriptions of morphological traits of sunn hemp. Two uniformity trials were conducted and the crops received identical treatment in all experimental area. Sunn hemp seeds were sown in rows 0.5 m apart with a plant density of 20 plants per row meter in a usable area of 52 m × 50 m. The following morphological traits were evaluated: plant height (PH, number of leaves (NL, stem diameter (SD, and root length (RL. These traits were assessed daily during two sowing periods—seeds were sown on October 22, 2014 (first period and December 3, 2014 (second period. Four plants were randomly collected daily, beginning 7 days after first period and 13 days after for second period, totaling 94 and 76 evaluation days, respectively. For Gompertz models the equation was used y=a*e^((?-e?^((b-c*xiand Logistic models the equation was used yi= a/(1+e^((-b-c*xi. The inflection points of the Gompertz and Logistic models were calculated and the goodness of fit was quantified using the adjusted coefficient of determination, Akaike information criterion, standard deviation of residuals, mean absolute deviation, mean absolute percentage error, and mean prediction error. Differences were observed between the Gompertz and Logistic models and between the experimental periods in the parameter estimate for all morphological traits measured. Satisfactory growth curve fittings were achieved for plant height, number of leaves, and stem diameter in both models using the evaluation criteria: coefficient of determination (R², Akaike information criterion (AIC, standard deviation of residuals (SDR, mean absolute deviation (MAD, mean absolute percentage error (MAPE, and mean prediction error (MPE.

  8. Influence of the precursor chemical composition on heavy metal adsorption properties of hemp (Cannabis Sativa fibers based biocarbon

    Directory of Open Access Journals (Sweden)

    Vukčević Marija M.

    2017-01-01

    Full Text Available Waste hemp (Cannabis sativa fibers were used as sustainable and renewable raw materials for production of low-cost biocarbon sorbent for heavy metals removal. Carbon precursors of different chemical composition were obtained by oxidative and alkaline treatments of hemp fibers. Influence of lignocellulosic precursor chemical composition on hemp fibers-based biocarbon (HFB characteristics was examined by BET surface area measurement, scanning electron microscopy and mass titration. It was found that lignin content and polymorphic transformation of cellulose increase the SBET of microporous HFBs, while hemicelluloses induce more homogeneous distribution of adsorption active sites. Heavy metal ions adsorption onto HFBs is primarily influenced by the amount of surface oxygen groups, while specific surface area plays a secondary role. Equilibrium data obtained for lead ions adsorption were analyzed by different nonlinear adsorption isotherms, and the best fitting model was chosen using standard deviation and Akaike information criterion (AICC. The maximum adsorption capacities of HFBs ranged from 103.1 to 116.3 mg Pb/g. Thermodynamic parameters showed that Pb2+ adsorption onto HFBs is a spontaneous and complex endothermic process, suggesting the coexistence of physisorption and chemisorption mechanisms. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. 172007 and Grant no. 172029

  9. Short-term Lost Productivity per Victim: Intimate Partner Violence, Sexual Violence, or Stalking.

    Science.gov (United States)

    Peterson, Cora; Liu, Yang; Kresnow, Marcie-Jo; Florence, Curtis; Merrick, Melissa T; DeGue, Sarah; Lokey, Colby N

    2018-05-15

    The purpose of this study is to estimate victims' lifetime short-term lost productivity because of intimate partner violence, sexual violence, or stalking. U.S. nationally representative data from the 2012 National Intimate Partner and Sexual Violence Survey were used to estimate a regression-adjusted average per victim (female and male) and total population number of cumulative short-term lost work and school days (or lost productivity) because of victimizations over victims' lifetimes. Victims' lost productivity was valued using a U.S. daily production estimate. Analysis was conducted in 2017. Non-institutionalized adults with some lifetime exposure to intimate partner violence, sexual violence, or stalking (n=6,718 respondents; survey-weighted n=130,795,789) reported nearly 741 million lost productive days because of victimizations by an average of 2.5 perpetrators per victim. The adjusted per victim average was 4.9 (95% CI=3.9, 5.9) days, controlling for victim, perpetrator, and violence type factors. The estimated societal cost of this short-term lost productivity was $730 per victim, or $110 billion across the lifetimes of all victims (2016 USD). Factors associated with victims having a higher number of lost days included a higher number of perpetrators and being female, as well as sexual violence, physical violence, or stalking victimization by an intimate partner perpetrator, stalking victimization by an acquaintance perpetrator, and sexual violence or stalking victimization by a family member perpetrator. Short-term lost productivity represents a minimum economic valuation of the immediate negative effects of intimate partner violence, sexual violence, and stalking. Victims' lost productivity affects family members, colleagues, and employers. Published by Elsevier Inc.

  10. Effect of Different Levels of Organic and Chemical Fertilizers on Yield, Harvest Index and Extract Percentage of Hemp (Cannabis sativa L.

    Directory of Open Access Journals (Sweden)

    S Laleh

    2018-02-01

    Full Text Available Introduction Hemp is a dioecious and annual plant. The most important use to this plant is in the food, drug, and natural fibers. Proper fertilizer management for a medicinal plant species is important for increasing its yield and maintaining the quality of active principles. Sustainable farming is on the basis of natural fertilizer application with the aim of decreasing chemical fertilizers. Various studies show that application of animal manure with chemical fertilizers (as N, P and … have positive effects on soil structure, microbial population, soil fertility, growth and yield of plant with the aim of protecting the environment. Therefore, the present study was under taken to evaluate the effect of organic amendments enriched with chemical fertilizers of nitrogen and phosphorus on yield and extract of hemp. Materials and Methods To study the effect of different levels of animal manure and chemical fertilizers, a split factorial experiment, based on complete randomized blocks design with three replications was conducted at the research Farm of Faculty of agriculture, University of Birjand, during the growing season 2014-2015. Experimental factors were animal manure (0, 10, 20 and 30 t. ha-1well rotted farmyard manure as the main plot, and factorial application of three levels of N (0, 50 and 100 kg N ha-1 as Urea with two levels of P (0 and 80 kg P2O5 ha-1 as triple and P was superphosphate as sub-plot. Animal manure, P and half of the N fertilizer were applied before planting and the other half of N were applied by top dressing. Hemp were planted 5 may on rows 60 cm apart, with 30 cm distance between each hemp on row, at the depth of 3-4 cm. Measured traits included leaf, stem and seed weights, stem height and diameter, 1000 seed weight, and leaves extract percentage per square meter in sub-plot for female plants of hemp. Also percentage of female plants calculated per sub-plot. Finally, all variables were analyzed by SAS software (V. 9

  11. Durability of Starch Based Biodegradable Plastics Reinforced with Manila Hemp Fibers

    OpenAIRE

    Shinji Ochi

    2011-01-01

    The biodegradability of Manila hemp fiber reinforced biodegradable plastics was studied for 240 days in a natural soil and 30 days in a compost soil. After biodegradability tests, weights were measured and both tensile strength tests and microscopic observation were performed to evaluate the biodegradation behavior of the composites. The results indicate that the tensile strength of the composites displays a sharp decrease for up to five days, followed by a gradual decrease. The weight loss a...

  12. Vulture worries stalk activists on Uttarayan

    African Journals Online (AJOL)

    2007-03-01

    Mar 1, 2007 ... Vulture worries stalk activists on Uttarayan. Anon. Ahmedabad – When kites take to the skies on Uttarayan, animal activists will be biting their nails in apprehension. Their main concern is the White-rumped. Vulture, a highly endangered species, of which only 137 birds are left in the city, according to figures ...

  13. Bio-oil production from cotton stalk

    International Nuclear Information System (INIS)

    Zheng Jilu; Yi Weiming; Wang Nana

    2008-01-01

    Cotton stalk was fast pyrolyzed at temperatures between 480 deg. C and 530 deg. C in a fluidized bed, and the main product of bio-oil is obtained. The experimental result shows that the highest bio-oil yield of 55 wt% was obtained at 510 deg. C for cotton stalk. The chemical composition of the bio-oil acquired was analyzed by GC-MS, and its heat value, stability, miscibility and corrosion characteristics were determined. These results showed that the bio-oil obtained can be directly used as a fuel oil for combustion in a boiler or a furnace without any upgrading. Alternatively, the fuel can be refined to be used by vehicles. Furthermore, the energy performance of the pyrolysis process was analyzed. In the pyrolysis system used in our experiment, some improvements to former pyrolysis systems are done. Two screw feeders were used to prevent jamming the feeding system, and the condenser is equipped with some nozzles and a heat exchanger to cool quickly the cleaned hot gas into bio-oil

  14. The influence of the type of lime on the hygric behaviour and bio-receptivity of hemp lime composites used for rendering applications in sustainable new construction and repair works.

    Science.gov (United States)

    Arizzi, Anna; Brümmer, Monika; Martín-Sanchez, Inés; Cultrone, Giuseppe; Viles, Heather

    2015-01-01

    The benefits of using sustainable building materials are linked not only to the adoption of manufacturing processes that entail reduced pollution, CO2 emissions and energy consumption, but also to the onset of improved performance in the building. In particular, hemp-lime composite shows low shrinkage and high thermal and acoustic insulating properties. However, this material also shows a great ability to absorb water, an aspect that can turn out to be negative for the long-term durability of the building. For this reason, the hygric properties of hemp-based composites need to be studied to ensure the correct use of this material in construction and repair works. The water absorption, drying and transpirability of hemp composites made with aerial (in the form of dry powder and putty) and hydraulic limes were investigated here and related to the microbial growth induced by the water movements within the material. Results show that hemp-natural hydraulic lime mixes exhibit the highest transpirability and drying rate, the lowest water absorption by immersion and capillary uptake and the least intense microbial attack and chromatic change. A microscopical study of the hemp shives also related their great ability to absorb water to the near-irreversible swelling of their structure under dry-wet conditions.

  15. Thermal Stress Analysis for Ceramics Stalk in the Low Pressure Die Casting Machine

    Science.gov (United States)

    Noda, Nao-Aki; Hendra, Nao-Aki; Takase, Yasushi; Li, Wenbin

    Low pressure die casting (LPDC) is defined as a net shape casting technology in which the molten metal is injected at high speeds and pressure into a metallic die. The LPDC process is playing an increasingly important role in the foundry industry as a low-cost and high-efficiency precision forming technique. The LPDC process is that the permanent die and filling systems are placed over the furnace containing the molten alloy. The filling of the cavity is obtained by forcing the molten metal by means of a pressurized gas in order to rise into a ceramic tube, which connects the die to the furnace. The ceramics tube called stalk has high temperature resistance and high corrosion resistance. However, attention should be paid to the thermal stress when the stalk is dipped into the molten aluminum. It is important to develop the design of the stalk to reduce the risk of fracture because of low fracture toughness of ceramics. In this paper, therefore, the finite element method is applied to calculate the thermal stresses when the stalk is dipped into the crucible by varying the dipping speeds and dipping directions. It is found that the thermal stress can be reduced by dipping slowly if the stalk is dipped into the crucible vertically, while the thermal stress can be reduced by dipping fast if it is dipped horizontally.

  16. Stalking. Part II: Victims' problems with the legal system and therapeutic considerations.

    Science.gov (United States)

    Abrams, K M; Robinson, G E

    1998-06-01

    This paper is the second of 2 parts reviewing the topic of stalking. It focuses on victims difficulties with the legal system and the psychotherapeutic tasks for victims and therapists. Computerized literature searches were used to identify relevant papers from psychiatric and legal journals. Publications by victims' and women's organizations provided additional information. Victims suffer emotional consequences from being stalked. Additional stress is caused by the legal system's lack of understanding of the causes and consequences of stalking and inadequate and unenforced laws. The treatment of victims requires a comprehensive approach, including education, supportive psychotherapy, and discussion of practical measures. Therapists may overidentify with the patient's powerlessness or hesitate to take on a case out of fear of the stalker. Female therapists may protect themselves against the realization of their own vulnerability by blaming the victim, while male therapists may feel defensive or overprotective. Stalking is a crime with major mental health consequences which is often poorly understood by society. Therapists need to be aware of the victim's emotional reactions, the types of legal and practical supports available, and the possible biases of society. Further education and research should be encouraged.

  17. Growth of wheat and lettuce and enzyme activities of soils under garlic stalk decomposition for different durations.

    Science.gov (United States)

    Han, Xu; Cheng, Zhihui; Meng, Huanwen

    2017-07-01

    Garlic (Allium sativum L.) stalk is a byproduct of garlic production that is normally thought of as waste but is now considered a useful biological resource. It is necessary to utilize this resource efficiently and reasonably to reduce environmental pollution and achieve sustainable agricultural development. The effect of garlic stalk decomposed for different durations was investigated in this study using wheat (Triticum aestivum L.) and lettuce (Lactuca sativa var. crispa L.) as test plants. Garlic stalk in early stages of decomposition inhibited the shoot and root lengths of wheat and lettuce, but it promoted the shoot and root lengths in later stages; longer durations of garlic stalk decomposition significantly increased the shoot and root fresh weights of wheat and lettuce, whereas shorter decomposing durations significantly decreased the shoot and root fresh weights; and garlic stalk at different decomposition durations increased the activities of urease, sucrase and alkaline phosphatase in soil where wheat or lettuce was planted. Garlic stalk decomposed for 30 or 40 days could promote the growth of wheat and lettuce plants as well as soil enzyme activities. These results may provide a scientific basis for the study and application of garlic stalk. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

  18. Effects of chemical-physical pre-treatment processes on hemp fibres for reinforcement of composites and textiles

    DEFF Research Database (Denmark)

    Thomsen, Anne Belinda; Thygesen, Anders; Bohn, Vibeke

    2006-01-01

    Retted hemp fibres were treated using chemical-physical pre-treatments and the material was characterised chemically in order to evaluate the effect of the pre-treatments, respectively, wet oxidation (WO), hydrothermal treatment (HT) and steam explosion (STEX). Process variables were addition...

  19. STALKED BARNACLES CONCHODERMA AURITUM ON AN ...

    African Journals Online (AJOL)

    lower jaw, the palate and the penis of the sperm whale - Carke 1966). The occurrence of. C. auritum on the body skin of an elephant seal is therefore ... It can be inferred from Sorensen's remark that "barnacles up to an inch in length have been seen ... " that a stalked barnacle was involved, and Laws indeed refers to those.

  20. Microstructure and nanomechanical properties of single stalks from diatom Didymosphenia geminata and their change due to adsorption of selected metal ions.

    Science.gov (United States)

    Zgłobicka, Izabela; Chlanda, Adrian; Woźniak, Michał; Łojkowski, Maciej; Szoszkiewicz, Robert; Mazurkiewicz-Pawlicka, Marta; Święszkowski, Wojciech; Wyroba, Elżbieta; Kurzydłowski, Krzysztof J

    2017-08-01

    We present topographical and nanomechanical characterization of single Didymosphenia geminata stalk. We compared the samples before and after adsorption of metal ions from freshwater samples. Transmission electron microscopy studies of single stalk cross-sections have shown three distinct layers and an additional thin extra coat on the external layer (called "EL"). Using scanning electron microscopy and atomic force microscopy (AFM), we found that topography of single stalks after ionic adsorption differed significantly from topography of pristine stalks. AFM nanoindentation studies in ambient conditions yielded elastic moduli of 214 ± 170 MPa for pristine stalks and 294 ± 108 MPa for stalks after ionic adsorption. Statistical tests showed that those results were significantly different. We conducted only preliminary comparisons between ionic adsorption of several stalks in air and in water. While the stalks with ions were on average stiffer than the pristine stalks in air, they became more compliant than the pristine stalks in water. We also heated the stalks and detected EL softening at 50°C ± 15°C. AFM nanoindentation in air on the softened samples yielded elastic moduli of 26 ± 9 MPa for pristine samples and 43 ± 22 MPa for stalks with absorbed metal ions. Substantial decrease of the EL elastic moduli after heating was expected. Significantly different elastic moduli for the samples after ionic adsorption in both cases (i.e., for heated and nonheated samples), as well as behavior of the stalks immersed in water, point to permanent structural EL changes due to ions. © 2017 Phycological Society of America.

  1. Oil-rich seeds from prehistoric contextsin southern Scandinavia – reflections on archaeobotanical records of fl ax, hemp, gold of pleasure, and corn spurrey

    DEFF Research Database (Denmark)

    Karg, Sabine

    2012-01-01

    . Although archaeobotanical records of oil plants are in most cases found in small numbers, they are often abundant at excavations in southern Scandinavia. This paper presents a diachronic review of plant records of fl ax (Linum usitatissimum L.) and hemp (Cannabis sativa L.), both known for the dual use...... as to whether corn spurrey had been a cultivar or if the seeds had been collected from wild populations. KEYWORDS: Archaeobotany, oil-rich seeds, fl ax, hemp, gold of pleasure, corn spurrey, southern Scandinavia...

  2. Hemp ( Cannabis sativa L.) seed oil: analytical and phytochemical characterization of the unsaponifiable fraction.

    Science.gov (United States)

    Montserrat-de la Paz, S; Marín-Aguilar, F; García-Giménez, M D; Fernández-Arche, M A

    2014-02-05

    Non-drug varieties of Cannabis sativa L., collectively namely as "hemp", have been an interesting source of food, fiber, and medicine for thousands of years. The ever-increasing demand for vegetables oils has made it essential to characterize additional vegetable oil through innovative uses of its components. The lipid profile showed that linoleic (55%), α-linolenic (16%), and oleic (11%) were the most abundant fatty acids. A yield (1.84-1.92%) of unsaponifiable matter was obtained, and the most interesting compounds were β-sitosterol (1905.00 ± 59.27 mg/kg of oil), campesterol (505.69 ± 32.04 mg/kg of oil), phytol (167.59 ± 1.81 mg/kg of oil), cycloartenol (90.55 ± 3.44 mg/kg of oil), and γ-tocopherol (73.38 ± 2.86 mg/100 g of oil). This study is an interesting contribution for C. sativa L. consideration as a source of bioactive compounds contributing to novel research applications for hemp seed oil in the pharmaceutical, cosmetic food, and other non-food industries.

  3. Silica Treatments: A Fire Retardant Strategy for Hemp Fabric/Epoxy Composites

    OpenAIRE

    Branda, Francesco; Malucelli, Giulio; Durante, Massimo; Piccolo, Alessandro; Mazzei, Pierluigi; Costantini, Aniello; Silvestri, Brigida; Pennetta, Miriam; Bifulco, Aurelio

    2016-01-01

    In this paper, for the first time, inexpensive waterglass solutions are exploited as a new, simple and ecofriendly chemical approach for promoting the formation of a silica-based coating on hemp fabrics, able to act as a thermal shield and to protect the latter from heat sources. Fourier Transform Infrared (FTIR) and solid-state Nuclear Magnetic Resonance (NMR) analysis confirm the formation of –C–O–Si– covalent bonds between the coating and the cellulosic substrate. The proposed waterglass t...

  4. Combined HPLC analysis of organic acids and furans formed during organosolv pulping of fiber hemp

    NARCIS (Netherlands)

    Gosselink, R.J.A.; Dam, van J.E.G.; Zomers, F.H.A.

    1995-01-01

    During organosolv pulping of fiber hemp (Cannabis sativa L) with a mixture of ethanol/water, delignification is catalyzed by released acetic acid and formic acid in the effluent. The major sources of acetic acid are the acetyl groups, as determined by means of the acetyl balance, whereas formic acid

  5. Controlled retting of hemp fibres: Effect of hydrothermal pre-treatmen tand enzymatic retting on the mechanical properties of unidirectiona lhemp/epoxy composites

    DEFF Research Database (Denmark)

    Liu, Ming; Silva, Diogo Alexandre Santos; Fernando, Dinesh

    2016-01-01

    The objective of this work was to investigate the use of hydrothermal pre-treatment and enzymatic retting to remove non-cellulosic compounds and thus improve the mechanical properties of hemp fibre/epoxy composites. Hydrothermal pre-treatment at 100 kPa and 121 °C combined with enzymatic retting...... produced fibres with the highest ultimate tensile strength (UTS) of 780 MPa. Compared to untreated fibres, this combined treatment exhibited a positive effect on the mechanical properties of hemp fibre/epoxy composites, resulting in high quality composites with low porosity factor (αpf) of 0.08.Traditional...

  6. Time Course of Resolution of Hyperprolactinemia After Transsphenoidal Surgery Among Patients Presenting with Pituitary Stalk Compression.

    Science.gov (United States)

    Zaidi, Hasan A; Cote, David J; Castlen, Joseph P; Burke, William T; Liu, Yong-Hui; Smith, Timothy R; Laws, Edward R

    2017-01-01

    Primary lactotroph disinhibition, or stalk effect, occurs when mechanical compression of the pituitary stalk disrupts the tonic inhibition by dopamine released by the hypothalamus. The resolution of pituitary stalk effect-related hyperprolactinemia postoperatively has not been studied in a large cohort of patients. We performed a retrospective review to investigate the time course of recovery of lactotroph disinhibition after transsphenoidal surgery. Medical records were retrospectively reviewed for all patients undergoing transsphenoidal surgery with the senior author from April 2008 to November 2014. Of 556 pituitary adenomas, 289 (52.0%) were eliminated: 77 (13.9%) had an immunohistochemically confirmed prolactinoma, 119 (21.4%) patients had previous surgery, 93 (16.7%) had incomplete medical records, leaving 267 patients (48.0%) for final analysis. Of these patients, 72 (27.0%) had increased serum prolactin levels (≥23.3 ng/mL), suggestive of pituitary stalk effect (maximum prolactin level = 148.0 ng/mL). Patients with stalk effect were more likely than those with normal serum prolactin levels to present with menstrual dysfunction (29.7% vs. 19.4%; P Transsphenoidal surgery can provide durable normalization of serum prolactin levels and related symptoms caused by pituitary stalk compression-related lactotroph disinhibition. Copyright © 2016 Elsevier Inc. All rights reserved.

  7. Body stalk anomaly in Denmark during 20 years (1970-1989)

    DEFF Research Database (Denmark)

    Bugge, Merete

    2012-01-01

    Body stalk anomaly is a severe defect of the abdominal wall with uncovered thoracic and/or abdominal organs. The umbilical cord is absent or very short. Here I present epidemiological and clinical data on 16 infants with body stalk anomaly. The 16 infants represent 3.4% of the 469 infants...... ascertained in an almost complete nationwide data set of live- and stillborn infants born with abdominal wall defects during the two decades 1970-1989 in Denmark. The prevalence was 0.12 per 10,000 live- and stillborn. Nine of the infants were stillbirths, seven were live births, and they all died shortly...

  8. Enhancement of Cotton Stalks Composting with Certain Microbial Inoculations

    Directory of Open Access Journals (Sweden)

    Osama Abdel-Twab Seoudi

    2013-01-01

    Full Text Available Effect of inoculation with Phanerochaete chrysosporium and Azotobacter chrococcum microbes on cotton stalks composting was studied in an attempt to achieve rapid maturity and desirable characteristics of produced compost. Composting process was maintained for 16 weeks under aerobic conditions with proper moisture content and turning piles. The C/N ratio of the mixtures was adjusted to about 30:1 before composting using chicken manure. Temperature evolution and its profile were monitored throughout the composting period. Mineralization rates of organic matter and changes in nitrogen content during composting stages were evaluated. Total plate count of mesophilic and thermophilic bacteria, cellulose decomposers and Azotobacter were determined during composting periods. The treatment of cotton stalks inoculated with both P. chrysosporium and Azotobacter gave the most desirable characteristics of the final product with respect to the narrow C/N ratio, high nitrogen content and high numbers of Azotobacter. The phytotoxicity test of compost extracts was evaluated. The use of P. chrysosporium in composting accelerated markedly decomposition process, so that 16 weeks composting enough to produce a stable and mature compost suitable for use as fertilizer while the fertilizer obtained by composting cotton stalks mixed with chicken manure and inoculated with microorganisms is highest quality Compost.

  9. 75 FR 81085 - National Stalking Awareness Month, 2011

    Science.gov (United States)

    2010-12-27

    ... victimization than men. Stalking can be a difficult crime to recognize. The majority of survivors do not report... affects too many Americans to remain a hidden crime, and a strong stand is required in order to both...

  10. Evaluation of cotton stalks destroyers

    OpenAIRE

    Bianchini, Aloisio; Borges, Pedro H. de M.

    2013-01-01

    The destruction of the cotton crop residues (cotton stalks) is a mandatory procedure in Brazil for prophylactic issues, but is a subject unexplored by the research and there are few studies that deal with this issue. However, this is not encouraged in recent decades, studies aimed at developing and evaluating equipment for this purpose. The present study had the objective to evaluate six methods for mechanical destruction of cotton crop residues. Each method was defined based on the principle...

  11. Crystallographic characterization and molecular symmetry of edestin, a legumin from hemp.

    Science.gov (United States)

    Patel, S; Cudney, R; McPherson, A

    1994-01-07

    Edestin, a legumin class reserve protein from hemp seeds having six identical subunits was crystallized from ammonium phosphate at pH 5 and subsequently characterized by X-ray diffraction. The crystals are of space group R32 with a = 127 A and gamma = 116 degrees having an equivalent triply centered hexagonal cell of a = b = 215 A, c = 80 A. There is one hexameric protein in the rhombohedral unit cell, hence the subunits of the Edestin molecule must be arranged with 32 point group symmetry.

  12. Enkele kanttekeningen bij de strafbaarstelling van stalking

    NARCIS (Netherlands)

    van Klink, B.M.J.; Royakkers, L.M.M.

    1998-01-01

    In dit artikel gaan wij nader in op het fenomeen stalking in het algemeen en het wetsvoorstel dienaangaande in het bijzonder. §2 biedt een conceptuele analyse van het begrip ¿belaging', dat door ons wordt opgevat als een vorm van geestelijke mishandeling. Beseft dient te worden dat het hierbij niet

  13. Formulation, Characterization and Properties of Hemp Seed Oil and Its Emulsions

    Directory of Open Access Journals (Sweden)

    Veronika Mikulcová

    2017-04-01

    Full Text Available The formulation, characterization, and anticipated antibacterial properties of hemp seed oil and its emulsions were investigated. The oil obtained from the seeds of Cannabis sativa L. in refined and unrefined form was characterized using iodine, saponification, acid values, and gas chromatography, and was employed for the preparation of stable oil-in-water emulsions. The emulsions were prepared using pairs of non-ionic surfactants (Tween, Span. The effects of the emulsification method (spontaneous emulsification vs. high-intensity stirring, hydrophilic lipophilic balance (HLB, type and concentration of surfactant, and oil type on the size and distribution of the emulsion particles were investigated. It was found that the ability to form stable emulsions with small, initial particle sizes is primarily dependent on the given method of preparation and the HLB value. The most efficient method of emulsification that afforded the best emulsions with the smallest particles (151 ± 1 nm comprised the high-energy method, and emulsions stable over the long-term were observed at HBL 9 with 10 wt % concentration of surfactants. Under high-intensity emulsification, refined and unrefined oils performed similarly. The oils as well as their emulsions were tested against the growth of selected bacteria using the disk diffusion and broth microdilution methods. The antibacterial effect of hemp seed oil was documented against Micrococcus luteus and Staphylococcus aureus subsp. aureus. The formulated emulsions did not exhibit the antibacterial activity that had been anticipated.

  14. Taxonomy of the African large carpenter bees of the genus Xylocopa Latreille, 1802, subgenus Xenoxylocopa Hurd & Moure, 1963 (Hymenoptera, Apidae

    Directory of Open Access Journals (Sweden)

    Jonathan R. Mawdsley

    2017-02-01

    Full Text Available The taxonomy of the genus Xylocopa Latreille, 1802, subgenus Xenoxylocopa Hurd & Moure, 1963, is reviewed. There is a single valid species in this subgenus, Xylocopa (Xenoxylocopa inconstans Smith, 1874, which is widely distributed throughout sub-Saharan Africa, from Senegal to Ethiopia and south to northern Republic of South Africa. Synonyms of X. inconstans include X. abyssinica Radoszkowski, 1899, proposed for a male specimen from Ethiopia, as well as three names proposed for females with yellow (rather than white dorsal pubescence: Mesotrichia chiyakensis Cockerell, 1908 (new synonym, X. inconstans var. flavescens Vachal, 1899, and X. inconstans var. flavocincta Friese, 1909. Quantitative analyses of body measurements and examination of male reproductive structures support the new synonymy of Mesotrichia chiyakensis with X. inconstans. Males and females of X. (X. inconstans are illustrated, along with male reproductive structures, and diagnostic characters and keys are provided to separate the males and females of X. (X. inconstans from those of species in other closely-allied African subgenera of the genus Xylocopa.

  15. A procedure for identifying textile bast fibres using microscopy: Flax, nettle/ramie, hemp and jute

    International Nuclear Information System (INIS)

    Bergfjord, Christian; Holst, Bodil

    2010-01-01

    Identifying and distinguishing between natural textile fibres is an important task in both archaeology and criminology. Wool, silk and cotton fibres can readily be distinguished from the textile bast fibres flax, nettle/ramie, hemp and jute. Distinguishing between the bast fibres is, however, not easily done and methods based on surface characteristics, chemical composition and cross section size and shape are not conclusive. A conclusive method based on X-ray microdiffraction exists, but as the method requires the use of a synchrotron it is not readily available. In this paper we present a simple procedure for identifying the above mentioned textile bast fibres. The procedure is based on measuring the fibrillar orientation with polarised light microscopy and detecting the presence of calcium oxalate crystals (CaC 2 O 4 ) in association with the fibres. To demonstrate the procedure, a series of fibre samples of flax, nettle, ramie, hemp and jute were investigated. The results are presented here. An advantage of the procedure is that only a small amount of fibre material is needed.

  16. A procedure for identifying textile bast fibres using microscopy: Flax, nettle/ramie, hemp and jute

    Energy Technology Data Exchange (ETDEWEB)

    Bergfjord, Christian, E-mail: christian.bergfjord@uib.no [Institute for Physics and Technology, University of Bergen, Allegt. 55, 5007 Bergen (Norway); Holst, Bodil, E-mail: bodil.holst@uib.no [Institute for Physics and Technology, University of Bergen, Allegt. 55, 5007 Bergen (Norway)

    2010-08-15

    Identifying and distinguishing between natural textile fibres is an important task in both archaeology and criminology. Wool, silk and cotton fibres can readily be distinguished from the textile bast fibres flax, nettle/ramie, hemp and jute. Distinguishing between the bast fibres is, however, not easily done and methods based on surface characteristics, chemical composition and cross section size and shape are not conclusive. A conclusive method based on X-ray microdiffraction exists, but as the method requires the use of a synchrotron it is not readily available. In this paper we present a simple procedure for identifying the above mentioned textile bast fibres. The procedure is based on measuring the fibrillar orientation with polarised light microscopy and detecting the presence of calcium oxalate crystals (CaC{sub 2}O{sub 4}) in association with the fibres. To demonstrate the procedure, a series of fibre samples of flax, nettle, ramie, hemp and jute were investigated. The results are presented here. An advantage of the procedure is that only a small amount of fibre material is needed.

  17. MCPA (4-Chloro-2-ethylphenoxyacetate) resistance in hemp-nettle (Galeopsis tetrahit L.).

    Science.gov (United States)

    Weinberg, Tsafrir; Stephenson, Gerald R; McLean, Michael D; Hall, J Christopher

    2006-11-29

    The physiological basis for MCPA resistance in a hemp-nettle (Galeopsis tetrahit L.) biotype, obtained from a MCPA-resistant field population, was investigated. Dose-response studies revealed that the resistance factor for MCPA, based on GR50 comparisons of total dry weight of resistant (R) and susceptible (S) plants, was 3.3. Resistance factors for fluroxypyr, dicamba, 2,4-D, glyphosate, and chlorsulfuron were 8.2, 1.7, 1.6, 0.7, and 0.6, respectively. MCPA resistance was not due to differences in absorption, because both R and S biotypes absorbed 54% of applied [14C]MCPA 72 h after treatment. However, R plants exported less (45 vs 58% S) recovered 14C out of treated leaves to the apical meristem (6 vs 13% S) and root (32 vs 38% S). In both biotypes, approximately 20% of the 14C recovered in planta was detected as MCPA metabolites. However, less of the 14C recovered in the roots of R plants was MCPA. Therefore, two different mechanisms protect R hemp-nettle from MCPA phytotoxicity: a lower rate of MCPA translocation and a higher rate of MCPA metabolism in the roots. In support of these results, genetic studies indicated that the inheritance of MCPA resistance is governed by at least two nuclear genes with additive effects.

  18. Soma of the Rigveda and an attempt to identify it.

    Science.gov (United States)

    Mahdihassan, S; Mehdi, F S

    1989-01-01

    Ephedra juice is used as the drink of longevity given even to the new born. This is an Aryan custom mentioned in Rigveda and followed even by the Romans. To trace the history of this custom would lead to identifying Soma = Ephedra. The original species of Ephedra or Soma proper would be Ephedra sinica, the Chinese plant. It is the one species with yellow stalks. This has been illustrated so that it confirms Rigveda speaking of Soma as "golden yellow." The name Soma is also a loan word from Chinese meaning "fire-yellow fibers of hemp." The plant Soma is described as "thousand boughs" and photographic evidence has been offered in support. Each stalk is rod-like resembling an arrow as Rigveda speaks of it. An illustration has been offered to show the plant with stalks which are straight and rod-like, comparable with an arrow.

  19. Joint approach based on clinical and imaging features to distinguish non-neoplastic from neoplastic pituitary stalk lesions.

    Directory of Open Access Journals (Sweden)

    Ji Ye Lee

    Full Text Available Distinguishing non-neoplastic pituitary stalk lesions (non-NPSLs from neoplastic pituitary stalk lesions (NPSLs is a major concern in guiding treatment for a thickened pituitary stalk. Our study aimed to aid provide preoperative diagnostic assistance by combining clinical and magnetic resonance imaging (MRI findings to distinguish non-NPSLs from NPSLs.We recruited 158 patients with thickened pituitary stalk lesions visible on MRI. Laboratory findings included hypopituitarism, diabetes insipidus (DI, and hyperprolactinemia. MR images were assessed for anterior-posterior thickness (mm, diffuse pituitary stalk thickening, cystic changes, a high T1 signal, and glandular or extrasellar involvement. A diagnostic model was developed using a recursive partitioning logistic regression analysis. The model was validated in an independent dataset comprising 63 patients, and its diagnostic performance was compared with that of the original radiological reports.A univariate analysis found significant associations of DI (P = 0.006, absence of extrasellar involvement (P = 0.002, and lower stalk thickness (P = 0.031 with non-NPSLs. A diagnostic model was created using the following parameters (in order of priority: 1 lack of extrasellar involvement, 2 stalk thickness < 5.3 mm, and 3 presence of DI. The diagnostic performance (area under the curve; AUC of this model in the independent set was 0.813, representing a significant improvement over the original radiological reports (AUC: 0.713, P = 0.029.The joint diagnostic approach based on clinical and imaging-based factors robustly distinguished non-NPSLs from NPSLs. This approach could guide treatment strategies and prevent unnecessary surgery in patients with non-NPSL.

  20. Effects of hemp (Cannabis sativa L.) seed oil press-cake and decaffeinated green tea leaves (Camellia sinensis) on functional characteristics of gluten-free crackers.

    Science.gov (United States)

    Radočaj, Olga; Dimić, Etelka; Tsao, Rong

    2014-03-01

    A mixture, simplex centroid, 2 components experimental design was used to evaluate the addition of hemp seed oil press-cake and decaffeinated green tea leaves, as functional ingredients to assess nutritional characteristics and antioxidant properties of gluten-free crackers. All samples with added hemp flour had much better nutritional qualities than the brown rice flour crackers in terms of higher protein, crude fibers, minerals, and essential fatty acids content. Likewise, all samples with added decaffeinated green tea leaves had much better antioxidant properties than crackers with no added green tea leaves. All crackers with added hemp flour had a significantly increased fiber content (39% to 249%) and decreased carbohydrate content (8.4% to 42.3%), compared to the brown rice flour crackers. All samples had antioxidant properties, even without the addition of green tea leaves. Optimization of the responses was conducted based on the maximized values for protein, fibers, omega-3 fatty acids content, as well as for the antioxidant activity and overall score. The suggested values for the addition of the hemp oil press-cake was 20% (total flour weight) with 4 g of decaffeinated green tea leaves that would provide protein content of 14.1 g/100 g; fibers content of 8.4 g/100 g; omega-3 fatty acids content of 3.2 g/100 g; antioxidant activity measured via 2,2-diphenyl-1-picrylhydrazyl value of 30.3 μmol TE/g d.w.; and an overall score of 8.9. This formulation has demonstrated potential application in the baking industry and marketing of these gluten-free crackers as a value-added functional product. Hemp seed oil press-cake as a by-product of cold-pressed oil processing and brown rice flour were used to design a functional gluten-free snack-type product-savory crackers. All crackers were high in minerals, fibers, and omega-3 fatty acids with a desirable omega-6/omega-3 fatty acids ratio. Green tea leaves were added to improve antioxidant activity, which greatly

  1. A comparison of soda and soda-AQ pulps from cotton stalks | Akgül ...

    African Journals Online (AJOL)

    In this study, cotton stalks (Gossypium hirsutum L.) were cooked using soda and soda-anthraquinone (AQ) process. Nine soda cooks were conducted by changing cooking conditions including active alkali charge and pulping time. Soda-AQ cooks were obtained by adding 0.075, 0.10, 0.15, 0.2% AQ (based on o.d stalks) to ...

  2. Short-Term Efficacy of CBD-Enriched Hemp Oil in Girls with Dysautonomic Syndrome after Human Papillomavirus Vaccination.

    Science.gov (United States)

    Palmieri, Beniamino; Laurino, Carmen; Vadalà, Maria

    2017-02-01

    Cannabidiol (CBD)-based treatments for several diseases, including Tourette's syndrome, multiple sclerosis, epilepsy, movement disorders and glaucoma, are proving to be beneficial and the scientific clinical background of the drug is continuously evolving. To investigate the short-term effect of CBD-enriched hemp oil for relieving symptoms and improving the life quality (QOL) in young girls with adverse drug effects (ADRs) following human papillomavirus (HPV) vaccine. In this anecdotal, retrospective, "compassionate-use", observational, open-label study, 12 females (age 12-24 years) with severe somatoform and dysautonomic syndrome following HPV vaccination were given sublingual CBD-rich hemp oil drops, 25 mg/kg per day supplemented by 2-5 mg/ml CBD once a week until a maximum dose of 150 mg/ml CBD per day was reached over a 3 month period. Patients' quality of life was evaluated using the medical outcome short-form health survey questionnaire (SF-36). Two patients dropped out due to iatrogenic adverse events and another two patients stopped the treatment early due to lack of any improvement. SF-36 showed significant benefits in the physical component score (P oil also significantly reduced body pain according to the SF-36 assessment. No significant differences from the start of treatment to several months post-treatment were detected in role limitations due to emotional reactions (P = 0.02). This study demonstrated the safety and tolerability of CBD-rich hemp oil and the primary efficacy endpoint. Randomized controlled trials are warranted to characterize the safety profile and efficacy of this compound.

  3. Synthesis of vertical MnO_2 wire arrays on hemp-derived carbon for efficient and robust green catalysts

    International Nuclear Information System (INIS)

    Yang, MinHo; Kim, Dong Seok; Sim, Jae-Wook; Jeong, Jae-Min; Kim, Do Hyun; Choi, Jae Hyung; Kim, Jinsoo; Kim, Seung-Soo; Choi, Bong Gill

    2017-01-01

    Highlights: • The three-dimensional nanocomposites based on vertical MnO_2 array on hemp-derived carbon (HDC) were prepared by hydrothermal method. • The 3D v-MnO_2/HDC nanocomposites showed well-defined porous nature with a high specific surface area of 382.3 m"2 g"−"1. • PET glycolysis was performed using the 3D v-MnO_2/HDC nanocomposites as a catalyst, leading to efficient catalytic performance. - Abstract: Three-dimensional (3D) carbon materials derived from waste biomass have been attracted increasing attention in catalysis and materials science because of their great potential of catalyst supports with respect to multi-functionality, unique structures, high surface area, and low cost. Here, we present a facile and efficient way for preparing 3D heterogeneous catalysts based on vertical MnO_2 wires deposited on hemp-derived 3D porous carbon. The 3D porous carbon materials are fabricated by carbonization and activation processes using hemp (Cannabis Sttiva L.). These 3D porous carbon materials are employed as catalyst supports for direct deposition of vertical MnO_2 wires using a one-step hydrothermal method. The XRD and XPS results reveal the crystalline structure of α-MnO_2 wires. The resultant composites are further employed as a catalyst for glycolysis of poly(ethylene terephthalate) (PET) with high conversion yield of 98%, which is expected to be expressly profitable for plastics recycling industry.

  4. Comparative pulping of sunflower stalks

    Directory of Open Access Journals (Sweden)

    Valerii Barbash

    2016-03-01

    Full Text Available The procedure of holocellulose content determination in non-wood plant raw materials was developed. The strength properties of pulp obtained from sunflower stalks by neutral-sulphite, soda, alkaline sulphite-anthraquinone-ethanol and peracetic methods of delignification were studied. Methodology of comparison of plant materials delignification methods using new lignin-carbohydrate diagram was proposed. It was shown, that the alkaline sulphite-anthraquinone-ethanol method of pulping is characterized by the highest delignification degree and is the most efficient among the studied methods

  5. Cyber stalking victimisation of women: Evaluating the effectiveness of current laws in India from restorative justice and therapeutic jurisprudential perspectives

    Directory of Open Access Journals (Sweden)

    Halder Debarati

    2015-01-01

    Full Text Available Victimisation of women through cyber stalking is one of the most serious crimes against women. Many countries including India have developed laws regulating cyber stalking. This article argues that since both, restorative justice (RJ and therapeutic jurisprudence (TJ are victim oriented, the issue of cyber stalking of women may be dealt with by RJ process and the laws in this regard must be analysed by the legal actors with a background in RJ and TJ philosophy. India had earlier taken up therapeutic punishment policy to enforce rights of the accused. But the modern principles of TJ have still not been considered in the RJ background in cyber stalking cases. This article therefore examines whether RJ and TJ principles can replace retributive principles for cyber stalking victimisation. It also examines the Indian cyber stalking law from RJ and TJ perspectives to assess its effectiveness for victims.

  6. Pituitary gland and its stalk observed by high resolution CT

    International Nuclear Information System (INIS)

    Nakagawa, Yoshinobu; Fukami, Tsuneharu; Matsumoto, Keizo.

    1982-01-01

    It seemed to be important to recognize the CT findings of normal pituitary gland and the stalk for the acurate morphological diagnosis of pituitary microadenoma. In a consecutive series of normal 103 cases, the CT scans obtained by high resolution CT (CE-CT, Metrizamide CT) were analized and compared with 6 cases of microadenoma. The pituitary stalk demonstrated by the reconstructed coronal CT was examined and the inclination of the stalk was measured. The mean value of the inclination of pituitary stalk was 1.4 +- 1.7 0 in normal group and 9.3 +- 2.4 0 in microadenoma group. The form of the pituitary gland demonstrated by a reconstructed mid-saggital CT were classified into the following 3 types. Type I : The gland filling the whole pituitary fossa. Type II : The gland filled with small CSF space localized in the upper-anterior part in the pituitary fossa. Type III : The enlarged CSF space of more than half of the depth of pituitary fossa and the gland localized in the retro-lower part. As for the shape of pituitary gland, type I was revealed in 26 cases (7 cases in male and 19 cases in female), Type II was revealed in 31 cases (12 cases in male and 19 cases in female), Type III was revealed in 46 cases (25 cases in male and 21 cases in female). Type I was shown in female, especially in 10 years old young female. In 19 cases of 30 years to 40 years female, Type II was shown in 9 cases. In 44 male cases, Type I and Type II were shown in all ages. In the aged, Type III was shown in more than the other types. On the other hand, Type I was noted in 5 out of 6 cases of microadenoma group. (author)

  7. Performance and Qualification of the Power Supply and Control Unit for the HEMP Thruster

    Science.gov (United States)

    Brag, R.; Herty, F.

    2014-08-01

    In 2013, Astrium GmbH delivered several flight model electronics for Electric Propulsion (EP) systems or corresponding components. One of the elements is a Power Supply and Control Unit (PSCU) for the Thales development "High Efficiency Multistage Plasma Thruster" (HEMP-T) (see Figure 1). This paper presents the PSCU specification and results of the qualification and acceptance phase of the EQM and the PFM.

  8. Investigation of the Mechanical Properties of Hybrid Carbon-Hemp Laminated Composites Used as Thermal Insulation for Different Industrial Applications

    Directory of Open Access Journals (Sweden)

    M. L. Scutaru

    2014-04-01

    Full Text Available Carbon-hemp composite laminate provides good thermal properties. For this reason this type of material is presently being used for various applications like insulator for airplanes, spaceships, nuclear reactors, and so forth. Unfortunately their mechanical properties are less studied. These characteristics are very important since they should be guaranteed also for important mechanical stress in addition to the thermal one. The present paper presents a study regarding the impact testing of some hybrid composite laminate panels based on polyester resin reinforced with both carbon and hemp fabric. The effects of different impact speeds on the mechanical behavior of these panels have been analyzed. The paper lays stress on the characterization of this hybrid composite laminate regarding the impact behavior of these panels by dropping a weight with low velocity.

  9. 77 FR 211 - National Stalking Awareness Month, 2012

    Science.gov (United States)

    2012-01-03

    ..., tragically, stalking can be a precursor to more violent offenses, including sexual assault and homicide. The... Federal agencies, we are promoting new tools to decrease the incidence of domestic violence, sexual... and harmful behavior. This month, let us come together to prevent abuse, violence, and harassment in...

  10. Neuraminidase stalk length and additional glycosylation of the hemagglutinin influence the virulence of influenza H5N1 viruses for mice.

    Science.gov (United States)

    Matsuoka, Yumiko; Swayne, David E; Thomas, Colleen; Rameix-Welti, Marie-Anne; Naffakh, Nadia; Warnes, Christine; Altholtz, Melanie; Donis, Ruben; Subbarao, Kanta

    2009-05-01

    Following circulation of avian influenza H5 and H7 viruses in poultry, the hemagglutinin (HA) can acquire additional glycosylation sites, and the neuraminidase (NA) stalk becomes shorter. We investigated whether these features play a role in the pathogenesis of infection in mammalian hosts. From 1996 to 2007, H5N1 viruses with a short NA stalk have become widespread in several avian species. Compared to viruses with a long-stalk NA, viruses with a short-stalk NA showed a decreased capacity to elute from red blood cells and an increased virulence in mice, but not in chickens. The presence of additional HA glycosylation sites had less of an effect on virulence than did NA stalk length. The short-stalk NA of H5N1 viruses circulating in Asia may contribute to virulence in humans.

  11. Neuraminidase Stalk Length and Additional Glycosylation of the Hemagglutinin Influence the Virulence of Influenza H5N1 Viruses for Mice▿

    Science.gov (United States)

    Matsuoka, Yumiko; Swayne, David E.; Thomas, Colleen; Rameix-Welti, Marie-Anne; Naffakh, Nadia; Warnes, Christine; Altholtz, Melanie; Donis, Ruben; Subbarao, Kanta

    2009-01-01

    Following circulation of avian influenza H5 and H7 viruses in poultry, the hemagglutinin (HA) can acquire additional glycosylation sites, and the neuraminidase (NA) stalk becomes shorter. We investigated whether these features play a role in the pathogenesis of infection in mammalian hosts. From 1996 to 2007, H5N1 viruses with a short NA stalk have become widespread in several avian species. Compared to viruses with a long-stalk NA, viruses with a short-stalk NA showed a decreased capacity to elute from red blood cells and an increased virulence in mice, but not in chickens. The presence of additional HA glycosylation sites had less of an effect on virulence than did NA stalk length. The short-stalk NA of H5N1 viruses circulating in Asia may contribute to virulence in humans. PMID:19225004

  12. Comparison of traditional field retting and Phlebia radiata Cel 26 retting of hemp fibres for fibre-reinforced composites

    DEFF Research Database (Denmark)

    Liu, Ming; Ale, Marcel Tutor; Kołaczkowski, Bartłomiej

    2017-01-01

    Classical field retting and controlled fungal retting of hemp using Phlebia radiata Cel 26 (a mutant with low cellulose degrading ability) were compared with pure pectinase treatment with regard to mechanical properties of the produced fibre/epoxy composites. For field retting a classification...

  13. High-resolution heavily T2-weighted magnetic resonance imaging for evaluation of the pituitary stalk in children with ectopic neurohypophysis

    Energy Technology Data Exchange (ETDEWEB)

    Sanharawi, Imane El; Tzarouchi, Loukia [Hopital Robert Debre, APHP, Service de Radiologie Pediatrique, Paris (France); Cardoen, Liesbeth [Hopital Robert Debre, APHP, Service de Radiologie Pediatrique, Paris (France); Universite Paris Diderot, Paris (France); Martinerie, Laetitia; Leger, Juliane; Carel, Jean-Claude [Universite Paris Diderot, Paris (France); Inserm U1141, DHU PROTECT, Paris (France); Hopital Robert Debre, APHP, Service d' Endocrinologie Pediatrique, Paris (France); Elmaleh-Berges, Monique [Hopital Robert Debre, APHP, Service de Radiologie Pediatrique, Paris (France); Inserm U1141, DHU PROTECT, Paris (France); Alison, Marianne [Hopital Robert Debre, APHP, Service de Radiologie Pediatrique, Paris (France); Universite Paris Diderot, Paris (France); Inserm U1141, DHU PROTECT, Paris (France)

    2017-05-15

    In anterior pituitary deficiency, patients with non visible pituitary stalk have more often multiple deficiencies and persistent deficiency than patients with visible pituitary stalk. To compare the diagnostic value of a high-resolution heavily T2-weighted sequence to 1.5-mm-thick unenhanced and contrast-enhanced sagittal T1-weighted sequences to assess the presence of the pituitary stalk in children with ectopic posterior pituitary gland. We retrospectively evaluated the MRI data of 14 children diagnosed with ectopic posterior pituitary gland between 2010 and 2014. We evaluated the presence of a pituitary stalk using a sagittal high-resolution heavily T2-weighted sequence and a 1.5-mm sagittal T1-weighted turbo spin-echo sequence before and after contrast medium administration. A pituitary stalk was present on at least one of the sequences in 10 of the 14 children (71%). T2-weighted sequence depicted the pituitary stalk in all 10 children, whereas the 1.5-mm-thick T1-weighted sequence depicted 2/10 (20%) before contrast injection and 8/10 (80%) after contrast injection (P=0.007). Compared with 1.5-mm-thick contrast-enhanced T1-weighted sequences, high-resolution heavily T2-weighted sequence demonstrates better sensitivity in detecting the pituitary stalk in children with ectopic posterior pituitary gland, suggesting that contrast injection is unnecessary to assess the presence of a pituitary stalk in this setting. (orig.)

  14. High-resolution heavily T2-weighted magnetic resonance imaging for evaluation of the pituitary stalk in children with ectopic neurohypophysis.

    Science.gov (United States)

    El Sanharawi, Imane; Tzarouchi, Loukia; Cardoen, Liesbeth; Martinerie, Laetitia; Leger, Juliane; Carel, Jean-Claude; Elmaleh-Berges, Monique; Alison, Marianne

    2017-05-01

    In anterior pituitary deficiency, patients with non visible pituitary stalk have more often multiple deficiencies and persistent deficiency than patients with visible pituitary stalk. To compare the diagnostic value of a high-resolution heavily T2-weighted sequence to 1.5-mm-thick unenhanced and contrast-enhanced sagittal T1-weighted sequences to assess the presence of the pituitary stalk in children with ectopic posterior pituitary gland. We retrospectively evaluated the MRI data of 14 children diagnosed with ectopic posterior pituitary gland between 2010 and 2014. We evaluated the presence of a pituitary stalk using a sagittal high-resolution heavily T2-weighted sequence and a 1.5-mm sagittal T1-weighted turbo spin-echo sequence before and after contrast medium administration. A pituitary stalk was present on at least one of the sequences in 10 of the 14 children (71%). T2-weighted sequence depicted the pituitary stalk in all 10 children, whereas the 1.5-mm-thick T1-weighted sequence depicted 2/10 (20%) before contrast injection and 8/10 (80%) after contrast injection (P=0.007). Compared with 1.5-mm-thick contrast-enhanced T1-weighted sequences, high-resolution heavily T2-weighted sequence demonstrates better sensitivity in detecting the pituitary stalk in children with ectopic posterior pituitary gland, suggesting that contrast injection is unnecessary to assess the presence of a pituitary stalk in this setting.

  15. Effects of chemical treatments on hemp fibre structure

    Energy Technology Data Exchange (ETDEWEB)

    Kabir, M.M., E-mail: kabirm@usq.edu.au [Centre of Excellence in Engineered Fibre Composite (CEEFC), Faculty of Engineering and Surveying, University of Southern Queensland, Toowoomba, Queensland 4350 (Australia); Wang, H. [Centre of Excellence in Engineered Fibre Composite (CEEFC), Faculty of Engineering and Surveying, University of Southern Queensland, Toowoomba, Queensland 4350 (Australia); Lau, K.T. [Centre of Excellence in Engineered Fibre Composite (CEEFC), Faculty of Engineering and Surveying, University of Southern Queensland, Toowoomba, Queensland 4350 (Australia); Department of Mechanical Engineering, The Hong Kong Polytechnic University, Kowloon, Hong Kong Special Administrative Region (Hong Kong); Cardona, F. [Centre of Excellence in Engineered Fibre Composite (CEEFC), Faculty of Engineering and Surveying, University of Southern Queensland, Toowoomba, Queensland 4350 (Australia)

    2013-07-01

    In this study, hemp fibres were treated with alkali, acetyl and silane chemicals. Fibre constituents such as cellulose, hemicellulose and lignin constituents were separated from treated fibres. The chemical and thermal influences of these constituents on the treated fibres were examined by using scanning electron microscope (SEM), fourier transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). Experimental results revealed that, hemicellulose was degraded faster than that of cellulose and lignin. Cellulose exhibited better thermal stability and lignin was degraded in a wide range of temperatures. The hydrophilic nature of the fibres was predominantly caused by the presence of hemicellulose and then lignin constituents. Hemicellulose and lignin were mostly removed by the alkalisation with higher concentrations of NaOH, followed by acetylation. Silane treatment could not remove the hemicellulose and lignin, rather this treatment facilitated coupling with the fibre constituents.

  16. Effects of chemical treatments on hemp fibre structure

    International Nuclear Information System (INIS)

    Kabir, M.M.; Wang, H.; Lau, K.T.; Cardona, F.

    2013-01-01

    In this study, hemp fibres were treated with alkali, acetyl and silane chemicals. Fibre constituents such as cellulose, hemicellulose and lignin constituents were separated from treated fibres. The chemical and thermal influences of these constituents on the treated fibres were examined by using scanning electron microscope (SEM), fourier transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). Experimental results revealed that, hemicellulose was degraded faster than that of cellulose and lignin. Cellulose exhibited better thermal stability and lignin was degraded in a wide range of temperatures. The hydrophilic nature of the fibres was predominantly caused by the presence of hemicellulose and then lignin constituents. Hemicellulose and lignin were mostly removed by the alkalisation with higher concentrations of NaOH, followed by acetylation. Silane treatment could not remove the hemicellulose and lignin, rather this treatment facilitated coupling with the fibre constituents.

  17. Thermal Decomposition Properties of Materials from Different Parts of Corn Stalk

    Directory of Open Access Journals (Sweden)

    Siwei Huang

    2015-02-01

    Full Text Available To help better utilize corn stalk (CS, pyrolysis behavior of materials from different parts of the CS including corn stalk without pith, corn root, and corn leaf were analyzed using thermogravimetric analysis (TGA at heating rates of 5, 10, 20, and 25 °C/min. The apparent activation energies determined by the Friedman method for corn stalk without pith, corn root, and corn leaf were in the range of 26.4 to 103.6 kJ/mol, 37.6 to 69.5 kJ/mol, and 35.0 to 103.9 kJ/mol, respectively, depending on the conversion. The main thermal decomposition occurred within a temperature range of 200 to 350 °C (±10 °C. Most of the volatile materials decomposed at less than a 0.8 conversion rate. At greater than a 0.8 conversion rate, the remaining material was mainly char, and the decomposition of char proceeded at higher conversion rates. Different pyrolysis characteristics in the CS indicated that different treatments should be chosen according to different parts for achieving the optimum conversion rate in practical applications.

  18. The crop-residue of fiber hemp cv. Futura 75: from a waste product to a source of botanical insecticides.

    Science.gov (United States)

    Benelli, Giovanni; Pavela, Roman; Lupidi, Giulio; Nabissi, Massimo; Petrelli, Riccardo; Ngahang Kamte, Stephane L; Cappellacci, Loredana; Fiorini, Dennis; Sut, Stefania; Dall'Acqua, Stefano; Maggi, Filippo

    2018-04-01

    In the attempt to exploit the potential of the monoecious fiber hemp cv. Futura 75 in new fields besides textile, cosmetics and food industry, its crop-residue given by leaves and inflorescences was subjected to hydrodistillation to obtain the essential oils. These are niche products representing an ideal candidate for the development of natural insecticides for the control and management of mosquito vectors, houseflies and moth pests. After GC-MS analysis highlighting a safe and legal chemical profile (THC in the range 0.004-0.012% dw), the leaf and inflorescence essential oils were investigated for the insecticidal potential against three insect targets: the larvae of Culex quinquefasciatus and Spodoptera littoralis and the adults of Musca domestica. The essential oil from inflorescences, showing (E)-caryophyllene (21.4%), myrcene (11.3%), cannabidiol (CBD, 11.1%), α-pinene (7.8%), terpinolene (7.6%), and α-humulene (7.1%) as the main components, was more effective than leaf oil against these insects, with LD 50 values of 65.8 μg/larva on S. littoralis, 122.1 μg/adult on M. domestica, and LC 50 of 124.5 μl/l on C. quinquefasciatus larvae. The hemp essential oil moderately inhibited the acetylcholinesterase (AChE), which is a target enzyme in pesticide science. Overall, these results shed light on the future application of fiber hemp crop-residue for the development of effective, eco-friendly and sustainable insecticides.

  19. Synthesis of vertical MnO{sub 2} wire arrays on hemp-derived carbon for efficient and robust green catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Yang, MinHo [Department of Materials Science and Engineering and Beckman Institute for Advanced Science and Technology, University of Illinois at Urbana–Champaign, Urbana, IL 61801 (United States); Kim, Dong Seok; Sim, Jae-Wook [Department of Chemical Engineering, Kangwon National University, 346 Joongang-ro, Samcheok, Gangwon-do 25913 (Korea, Republic of); Jeong, Jae-Min; Kim, Do Hyun [Department of Chemical & Biomolecular Engineering, KAIST, 291 Daehak-ro, Yuseong-gu, Daejeon 34141 (Korea, Republic of); Choi, Jae Hyung [Department of Chemical Engineering, Kangwon National University, 346 Joongang-ro, Samcheok, Gangwon-do 25913 (Korea, Republic of); Department of Chemical Engineering, Pukyong National University, 365 Sinseon-ro, Nam-gu, Busan 48513 (Korea, Republic of); Kim, Jinsoo [Department of Chemical Engineering, Kyung Hee University, 1732, Daogyong-daero, Giheung-gu, Yongin, Gyeonggi-do 17104 (Korea, Republic of); Kim, Seung-Soo, E-mail: sskim2008@kangwon.ac.kr [Department of Chemical Engineering, Kangwon National University, 346 Joongang-ro, Samcheok, Gangwon-do 25913 (Korea, Republic of); Choi, Bong Gill, E-mail: bgchoi@kangwon.ac.kr [Department of Chemical Engineering, Kangwon National University, 346 Joongang-ro, Samcheok, Gangwon-do 25913 (Korea, Republic of)

    2017-06-15

    Highlights: • The three-dimensional nanocomposites based on vertical MnO{sub 2} array on hemp-derived carbon (HDC) were prepared by hydrothermal method. • The 3D v-MnO{sub 2}/HDC nanocomposites showed well-defined porous nature with a high specific surface area of 382.3 m{sup 2} g{sup −1}. • PET glycolysis was performed using the 3D v-MnO{sub 2}/HDC nanocomposites as a catalyst, leading to efficient catalytic performance. - Abstract: Three-dimensional (3D) carbon materials derived from waste biomass have been attracted increasing attention in catalysis and materials science because of their great potential of catalyst supports with respect to multi-functionality, unique structures, high surface area, and low cost. Here, we present a facile and efficient way for preparing 3D heterogeneous catalysts based on vertical MnO{sub 2} wires deposited on hemp-derived 3D porous carbon. The 3D porous carbon materials are fabricated by carbonization and activation processes using hemp (Cannabis Sttiva L.). These 3D porous carbon materials are employed as catalyst supports for direct deposition of vertical MnO{sub 2} wires using a one-step hydrothermal method. The XRD and XPS results reveal the crystalline structure of α-MnO{sub 2} wires. The resultant composites are further employed as a catalyst for glycolysis of poly(ethylene terephthalate) (PET) with high conversion yield of 98%, which is expected to be expressly profitable for plastics recycling industry.

  20. Measurement of the heat of smoldering combustion in straws and stalks by means of simultaneous thermal analysis

    Energy Technology Data Exchange (ETDEWEB)

    He, Fang; Yi, Weiming; Zha, Jianwen [School of Light Industry and Agricultural Engineering, Shandong University of Technology, Zibo, Shandong 255049 (China)

    2009-01-15

    In order to investigate reaction heat of agro-stalks smoldering, wheat straw, corn stalk, cotton stalk, millet straw, sorghum stalk and sweet potato rattan powder were smoldered and pyrolyzed in a simultaneous thermal analyzer (STA). The samples were placed in a platinum crucible (5 mm x 5 mm) with a lid (with a 1 mm hole) on a high-accuracy differential scanning calorimetry-heat capacity (DSC-cp) holder in the furnace of an STA and heated from 303 to 1073 K at a heating rate of 10 K min{sup -1}. Sweeping gas with a flow rate of 25 ml min{sup -1} was air and nitrogen during smoldering and pyrolysis, respectively. Results showed that the heat emission characteristic of the smoldering process differed remarkably from the pyrolysis process. Based on the analysis of the DSC curves, oxidative polymer degradation heat and char oxidation heat were obtained from experimental data. It showed that the oxidative polymer degradation heat of the agro-stalks is more than 6.92 MJ kg{sup -1} consumed matter, higher than that of cellulose paper. And char oxidation heat is around 23 MJ kg{sup -1} consumed matter, similar to that of cellulose paper, but higher than that of cigarette. Total net heat emission of smoldering in STA was also obtained. These data can be used as reference data in analyzing smoldering of agro-stalks under similar conditions. (author)

  1. [Effects of cotton stalk biochar on microbial community structure and function of continuous cropping cotton rhizosphere soil in Xinjiang, China].

    Science.gov (United States)

    Gu, Mei-ying; Tang, Guang-mu; Liu, Hong-liang; Li, Zhi-qiang; Liu, Xiao-wei; Xu, Wan-li

    2016-01-01

    In this study, field trials were conducted to examine the effects of cotton stalk biochar on microbial population, function and structural diversity of microorganisms in rhizosphere soil of continuous cotton cropping field in Xinjiang by plate count, Biolog and DGGE methods. The experiment was a factorial design with four treatments: 1) normal fertilization with cotton stalk removed (NPK); 2) normal fertilization with cotton stalk powdered and returned to field (NPKS); 3) normal fertilization plus cotton stalk biochar at 22.50 t · hm⁻² (NPKB₁); and 4) normal fertilization plus cotton stalk biochar at 45.00 t · hm⁻² (NPKB₂). The results showed that cotton stalk biochar application obviously increased the numbers of bacteria and actinomycetes in the rhizospheric soil. Compared with NPK treatment, the number of fungi was significantly increased in the NPKB₁treatment, but not in the NPKB₂ treatment. However, the number of fungi was generally lower in the biochar amended (NPKB₁, NPKB₂) than in the cotton stalk applied plots (NPKS). Application of cotton stalk biochar increased values of AWCD, and significantly improved microbial richness index, suggesting that the microbial ability of utilizing carbohydrates, amino acids and carboxylic acids, especially phenolic acids was enhanced. The number of DGGE bands of NPKB₂ treatment was the greatest, with some species of Gemmatimonadetes, Acidobacteria, Proteobacteria and Actinobacteria being enriched. UPGMC Cluster analysis pointed out that bacterial communities in the rhizospheric soil of NPKB₂ treatment were different from those in the NPK, NPKS and NPKB₁treatments, which belonged to the same cluster. These results indicated that application of cotton stalk biochar could significantly increase microbial diversity and change soil bacterial community structure in the cotton rhizosphere soil, thus improving the health of soil ecosystem.

  2. Effect of Preserving the Pituitary Stalk During Resection of Craniopharyngioma in Children on the Diabetes Insipidus and Relapse Rates and Long-Term Outcomes.

    Science.gov (United States)

    Cheng, Jing; Fan, Yanqin; Cen, Bo

    2017-09-01

    The objective of this study was to investigate the effect of preserving an infiltrated pituitary stalk during the resection of craniopharyngioma of pituitary stalk origin on postoperative outcomes and thus provide a theoretical basis for microsurgical treatment and prognosis. We screened the clinical data of all 103 pediatric patients with craniopharyngioma undergoing surgical treatment at our department between January 2006 and January 2013 and conducted a retrospective analysis of 82 patients with craniopharyngioma originating in the pituitary stalk. The patients were followed up from 12 months to 8 years. We analyzed the effect of preserving the pituitary stalk on the early and persistent diabetes insipidus rates, postoperative relapse rate, and mortality. In the total resection group (n = 67), the early and persistent diabetes insipidus rates were significantly lower in the 46 patients (68.7%) with a pituitary stalk than in those whose pituitary stalk was removed (P  0.05). In the subtotal resection group (n = 15), a significant difference was observed in the early and persistent diabetes insipidus rates (P  0.05). For children with craniopharyngioma of pituitary stalk origin, preserving the pituitary stalk has a significant effect on the early and persistent diabetes insipidus rates. When intraoperative exploration showed excessive adhesion between the tumor and pituitary stalk, we opted to preserve the pituitary stalk, which significantly reduced the early and persistent postoperative diabetes insipidus rates, without significantly increasing the relapse or mortality rate.

  3. Characterization of a thermoforming composite material made from hemp fibers and polypropylene

    Directory of Open Access Journals (Sweden)

    Ciupan Emilia

    2017-01-01

    Full Text Available The paper refers to a composite material developed for manufacturing thermoformed products with applications in furniture making, automotive industry etc., a method and machinery for manufacturing the material in unwoven form. From this material, Research and Development Department of TAPARO SA has designed and built a series of furniture components. The composite material made of a thermoplastic fibrous component and hemp fibre component, the way of obtaining and the properties of the thermoformed material presented in the paper are necessary in the process of designing and optimizing the parts.

  4. Mechanical and dielectric characterization of hemp fibre reinforced polypropylene (HFRPP by dry impregnation process

    Directory of Open Access Journals (Sweden)

    2010-03-01

    Full Text Available Natural fibres such as jute, coir, sisal, bamboo and pineapple are known to have high specific strength and can be effectively used in composites in various applications. The use of hemp fibres to reinforce the polymer aroused great interest and expectations amongst scientists and materials engineers. In this paper, composites with isotactic polypropylene (iPP matrix and hemp fibres were studied. These materials were manufactured via the patented FIBROLINE process based on the principle of the dry impregnation of a fibre assembly with a thermoplastic powder (iPP, using an alternating electric field. The aim of this paper is to show the influence of fibre/matrix interfaces on dielectric properties coupled with mechanical behaviours. Fibres or more probably the fibre/matrix interfaces allow the diffusion of electric charges and delocalise the polarisation energy. In this way, damages are limited during mechanical loading and the mechanical properties of the composites increase. The structure of composite samples was investigated by X-ray and FTIR analysis. The mechanical properties were analysed by quasistatic and dynamic tests. The dielectric investigations were carried out using the SEMME (Scanning Electron Microscope Mirror Effect method coupled with the measurement of the induced current (ICM.

  5. Preparation of nitrogen-doped cotton stalk microporous activated carbon fiber electrodes with different surface area from hexamethylenetetramine-modified cotton stalk for electrochemical degradation of methylene blue

    Directory of Open Access Journals (Sweden)

    Kunquan Li

    Full Text Available Cotton-stalk activated carbon fibers (CSCFs with controllable micropore area and nitrogen content were prepared as an efficient electrode from hexamethylenetetramine-modified cotton stalk by steam/ammonia activation. The influence of microporous area, nitrogen content, voltage and initial concentration on the electrical degradation efficiency of methylene blue (MB was evaluated by using CSCFs as anode. Results showed that the CSCF electrodes exhibited excellent MB electrochemical degradation ability including decolorization and COD removal. Increasing micropore surface area and nitrogen content of CSCF anode leaded to a corresponding increase in MB removal. The prepared CSCF-800-15-N, which has highest N content but lowest microporous area, attained the best degradation effect with 97% MB decolorization ratio for 5 mg/L MB at 12 V in 4 h, implying the doped nitrogen played a prominent role in improving the electrochemical degradation ability. The electrical degradation reaction was well described by first-order kinetics model. Overall, the aforesaid findings suggested that the nitrogen-doped CSCFs were potential electrode materials, and their electrical degradation abilities could be effectively enhanced by controlling the nitrogen content and micropore surface area. Keywords: Cotton stalk, Nitrogen content, Electrode, Surface area, Methylene blue

  6. EFFECTS INDUCED BY DIETHYL SULPHATE ON SOME CYTOGENETICAL PARAMETERS AND LENGTH GROWTH OF HEMP PLANTLETS

    Directory of Open Access Journals (Sweden)

    Elena Truta

    2007-08-01

    Full Text Available The hemp seeds were treated with diethyl sulphate, in four concentrations (0.1%, 0.25%, 0.5%, and 1% and in two variants of alkylant exposure (3 and 6 hours. The length growth of plantlets, mitotic index and frequency of chromosomal aberrations were the analyzed parameters. Significant modifications were obtained at the level of parameters in variants treated with DES, comparatively with control.

  7. Testing of DNA isolation for the identification of hemp

    Directory of Open Access Journals (Sweden)

    Tomáš Vyhnánek

    2015-12-01

    Full Text Available Hemp is diploid organism (2n = 2x = 20, genome size 534 Mb with nine pairs of autosomes plus XX (♀ or XY (♂ chromosomes. Cannabis sativa L. is an important economic plant for the production of food, fibre, oils, and intoxicants. Genotypes (varieties or chemovar of hemp with low Δ9-tetrahydrocannabinol content are used for industrial applications. Varieties with high Δ9-tetrahydrocannabinol or high cannabidiol content are used for medicinal applications. Biochemical and molecular methods can be used for identification and classification. An important step for molecular biology methods is to obtain the matrix of the native and sufficiently pure DNA. We tested two different experimental variant of samples (20 mg and 100 mg of seeds, oilcake and dried flowers for analysis of the Italian variety Carmagnola for analysis (harvested in 2014, Hempoint Ltd., Czech Republic. The DNeasy® Plant Mini Kit (Qiagen, GE was used to isolate the DNA. The DNA concentration and purity was assessed by agarose electrophoresis and via a spectrophotometer. Samples of lower weight yielded lower values of DNA concentration (average 16.30 - 38.90 ng.µL-1, but with better purity than samples of higher weight (ratio A260nm/A280nm for low-weight samples was near 1.80. To test the applicability of DNA analysis, we used two SSR markers (CAN1347 and CAN2913. PCR products were separated on 1% agarose and on 8% polyacrylamide electrophoresis. DNA samples obtained from samples of higher weight exhibited less PCR amplification than samples of lower weight. We found no effect of sample weight on the formation of non-specific amplification products during the PCR reaction. Based on our results we can be recommended for practical isolation procedure using DNeasy® Plant Mini Kit with lower of sample weight (20 mg. In future work the procedure for DNA isolating from wheat-cannabis products, e. g. breads, rolls or pasta, will be optimized.

  8. Gene duplication, tissue-specific gene expression and sexual conflict in stalk-eyed flies (Diopsidae).

    Science.gov (United States)

    Baker, Richard H; Narechania, Apurva; Johns, Philip M; Wilkinson, Gerald S

    2012-08-19

    Gene duplication provides an essential source of novel genetic material to facilitate rapid morphological evolution. Traits involved in reproduction and sexual dimorphism represent some of the fastest evolving traits in nature, and gene duplication is intricately involved in the origin and evolution of these traits. Here, we review genomic research on stalk-eyed flies (Diopsidae) that has been used to examine the extent of gene duplication and its role in the genetic architecture of sexual dimorphism. Stalk-eyed flies are remarkable because of the elongation of the head into long stalks, with the eyes and antenna laterally displaced at the ends of these stalks. Many species are strongly sexually dimorphic for eyespan, and these flies have become a model system for studying sexual selection. Using both expressed sequence tag and next-generation sequencing, we have established an extensive database of gene expression in the developing eye-antennal imaginal disc, the adult head and testes. Duplicated genes exhibit narrower expression patterns than non-duplicated genes, and the testes, in particular, provide an abundant source of gene duplication. Within somatic tissue, duplicated genes are more likely to be differentially expressed between the sexes, suggesting gene duplication may provide a mechanism for resolving sexual conflict.

  9. Stability of the 'L12 stalk' in ribosomes from mesophilic and (hyper)thermophilic Archaea and Bacteria.

    Science.gov (United States)

    Shcherbakov, D; Dontsova, M; Tribus, M; Garber, M; Piendl, W

    2006-01-01

    The ribosomal stalk complex, consisting of one molecule of L10 and four or six molecules of L12, is attached to 23S rRNA via protein L10. This complex forms the so-called 'L12 stalk' on the 50S ribosomal subunit. Ribosomal protein L11 binds to the same region of 23S rRNA and is located at the base of the 'L12 stalk'. The 'L12 stalk' plays a key role in the interaction of the ribosome with translation factors. In this study stalk complexes from mesophilic and (hyper)thermophilic species of the archaeal genus Methanococcus and from the Archaeon Sulfolobus solfataricus, as well as from the Bacteria Escherichia coli, Geobacillus stearothermophilus and Thermus thermophilus, were overproduced in E.coli and purified under non-denaturing conditions. Using filter-binding assays the affinities of the archaeal and bacterial complexes to their specific 23S rRNA target site were analyzed at different pH, ionic strength and temperature. Affinities of both archaeal and bacterial complexes for 23S rRNA vary by more than two orders of magnitude, correlating very well with the growth temperatures of the organisms. A cooperative effect of binding to 23S rRNA of protein L11 and the L10/L12(4) complex from mesophilic and thermophilic Archaea was shown to be temperature-dependent.

  10. Synthesis of vertical MnO2 wire arrays on hemp-derived carbon for efficient and robust green catalysts

    Science.gov (United States)

    Yang, MinHo; Kim, Dong Seok; Sim, Jae-Wook; Jeong, Jae-Min; Kim, Do Hyun; Choi, Jae Hyung; Kim, Jinsoo; Kim, Seung-Soo; Choi, Bong Gill

    2017-06-01

    Three-dimensional (3D) carbon materials derived from waste biomass have been attracted increasing attention in catalysis and materials science because of their great potential of catalyst supports with respect to multi-functionality, unique structures, high surface area, and low cost. Here, we present a facile and efficient way for preparing 3D heterogeneous catalysts based on vertical MnO2 wires deposited on hemp-derived 3D porous carbon. The 3D porous carbon materials are fabricated by carbonization and activation processes using hemp (Cannabis Sttiva L.). These 3D porous carbon materials are employed as catalyst supports for direct deposition of vertical MnO2 wires using a one-step hydrothermal method. The XRD and XPS results reveal the crystalline structure of α-MnO2 wires. The resultant composites are further employed as a catalyst for glycolysis of poly(ethylene terephthalate) (PET) with high conversion yield of 98%, which is expected to be expressly profitable for plastics recycling industry.

  11. Entre les violences conjugales et le harcèlement moral : le stalking .

    Directory of Open Access Journals (Sweden)

    Nicolas Desurmont

    2007-09-01

    Full Text Available Ce livre de la criminologue Murielle Anteo est le premier publié en langue française sur le stalking si l’on excepte les travaux encore inédits de Virginie Léon (2004. Comme le rappelle l’auteure, le terme est emprunté à l’anglais to stalk (hanter, rôder, et désigne un comportement menaçant, initié par un individu dont l’objectif conscient ou inconscient est l’objectivation de sa victime à des fins de domination. L’agression prend différentes formes : ...

  12. Thermogravimetric kinetics of corn stalk pretreated by oleaginous fungi Cunninghamella echinulata.

    Science.gov (United States)

    Wu, Jianguo; Gao, Shi; Wan, Jilin; Zeng, Yelin; Ma, Fuying; Zhang, Xiaoyu

    2011-04-01

    The thermogravimetric and composition of corn stalk pretreated by oleaginous fungi Cunninghamella echinulata had been studied in this paper. Results indicated that pretreatment by oleaginous fungi C. echinulata could decrease the activation energy and make the pyrolysis more efficient and energy-saving. By bio-pretreatment, the contents of elements agreed with the weight loss, sugar content, and oil contents, especially the sulfur content was greatly decreased, greatly eliminating the inventory of gas contamination such as the emission of SOx and making the pyrolysis more environmentally friendly. Therefore, corn stalk with sugar pretreated by oleaginous fungi C. echinulata should be a good pyrolysis material to obtain high quality bio-oil. Copyright © 2011 Elsevier Ltd. All rights reserved.

  13. Carbohydrate Status of Tulip Bulbs during Cold-Induced Flower Stalk Elongation and Flowering.

    Science.gov (United States)

    Lambrechts, H.; Rook, F.; Kolloffel, C.

    1994-01-01

    The effect of a cold treatment on the carbohydrate status of the scales and flower stalk of Tulipa gesneriana L. cv Apeldoorn bulbs during growth after planting was studied and compared with bulbs not given cold treatment. Bulbs were stored dry for 12 weeks at 5[deg]C (precooled) or 17[deg]C (noncooled). Only the 5[deg]C treatment led to rapid flower stalk elongation and flowering following planting at higher temperatures. Precooling enhanced mobilization of starch, fructans, and sucrose in the scales. The cold-stimulated starch breakdown was initially accompanied by increased [alpha]-amylase activity per scale. In noncooled bulbs, [alpha]-amylase activity slightly decreased or remained more or less constant. Cold-induced flower stalk elongation was partially accompanied by a decrease in the sucrose content and an increase in the glucose content and invertase activity per g dry weight. The starch content in internodes initially decreased and subsequently increased; [alpha]-amylase activity per g dry weight of the lowermost internode showed a peak pattern during starch breakdown and increased thereafter. The internodes of noncooled bulbs, on the contrary, accumulated sucrose. Their glucose content and invertase activity per g dry weight remained low. Starch breakdown was not found and [alpha]-amylase activity per g dry weight of the lowermost internode remained at a low level. Precooling of tulip bulbs thus favors reserve mobilization in the scales and flower stalk and glucose accumulation in the elongating internodes. PMID:12232100

  14. Innovative Prototype for Separate Harvesting of Cynara Cardunculus Achenes and Stalks

    Energy Technology Data Exchange (ETDEWEB)

    Pari, L.; Fedrizzi, M.; Pansini, L. (Consiglio per la Ricerca e la Sperimentazione in Agricoltura, Unita di Ricerca per l' Ingegneria Agraria, Monterotondo, RM (Italy))

    2008-10-15

    The CRA-ING took part to the Cynara cardunculus harvesting tests organized in Spain in 2007, where UPM has experimental cultivations in the Instituto Madrileno de Investigacion y Desarrollo Rural, Agrario y Alimentario (IMIDRA) de la Consejeria de Economia y Innovacion Tecnologica de la Comunidad de Madrid in El Encin, near Alcala De Henarez. The harvesting tests were carried out in week 33 (August 13th-17th); the cultivation was found part in good condition of maturity, part still not ready for harvesting. The test was carried out on the dried part of the crops. The tests aimed at evaluating a new mechanical equipment (head) working connected to a selfpropelled combine for separated harvesting of the different fractions obtainable by the cultivation assigned to different transformation: oil extraction from seeds and energy production from epigeous biomass combustion. During the tests carried out in 2006 in Portugal and Spain, it was observed how a combine harvester with a maize head was able to separate the seed with good accuracy. Likewise the difficulty of collecting the lignocellulosic fraction after its passage was highlighted. A combine with a wheat head could cut the stalk in an appropriate height range, but could not separate the head from the stalk. A sunflower head cut the capitula, but not the stalk. The project concept, supplied to a Firm that already builds heads for maize, wheat, sunflowers, soybean and so on, included the upper devices of a maize head and a classic wheat head (without the paddle wheel) in the lower part, to obtain capitula detachment and effective threshing and, at the same time, the stalk cut. Some modifications were specified to allow the cut of the stalk next to the ground and its successive tier in the space between the front wheels, where the discharge system of the threshing device would then provide to drop the remains of the capitula threshing. The basic concept of the machine, to separate and thresh the capitula and to drop

  15. Microwave-assisted ionic liquid-mediated rapid catalytic conversion of non-edible lignocellulosic Sunn hemp fibres to biofuels.

    Science.gov (United States)

    Paul, Souvik Kumar; Chakraborty, Saikat

    2018-04-01

    Sunn hemp fibre - a cellulose-rich crystalline non-food energy crop, containing 75.6% cellulose, 10.05% hemicellulose, 10.32% lignin, with high crystallinity (80.17%) and degree of polymerization (650) - is identified as a new non-food substrate for lignocellulosic biofuel production. Microwave irradiation is employed to rapidly rupture the cellulose's glycosidic bonds and enhance glucose yield to 78.7% at 160 °C in only 46 min. The reactants - long-chain cellulose, ionic liquid, transition metal catalyst, and water - form a polar supramolecular complex that rotates under the microwave's alternating polarity and rapidly dissipates the electromagnetic energy through molecular collisions, thus accelerating glycosidic bond breakage. In 46 min, 1 kg of Sunn hemp fibres containing 756 g of cellulose produces 595 g of glucose at 160 °C, and 203 g of hydroxymethyl furfural (furanic biofuel precursor) at 180 °C. Yeast mediated glucose fermentation produces 75.6% bioethanol yield at 30 °C, and the ionic liquid is recycled for cost-effectiveness. Copyright © 2018 Elsevier Ltd. All rights reserved.

  16. Raman spectroscopy for the characterization of different fractions of hemp essential oil extracted at 130 °C using steam distillation method

    Science.gov (United States)

    Hanif, Muhammad Asif; Nawaz, Haq; Naz, Saima; Mukhtar, Rubina; Rashid, Nosheen; Bhatti, Ijaz Ahmad; Saleem, Muhammad

    2017-07-01

    In this study, Raman spectroscopy along with Principal Component Analysis (PCA) is used for the characterization of pure essential oil (pure EO) isolated from the leaves of the Hemp (Cannabis sativa L.,) as well as its different fractions obtained by fractional distillation process. Raman spectra of pure Hemp essential oil and its different fractions show characteristic key bands of main volatile terpenes and terpenoids, which significantly differentiate them from each other. These bands provide information about the chemical composition of sample under investigation and hence can be used as Raman spectral markers for the qualitative monitoring of the pure EO and different fractions containing different active compounds. PCA differentiates the Raman spectral data into different clusters and loadings of the PCA further confirm the biological origin of the different fractions of the essential oil.

  17. Pyrolysis Characteristics of Corn Stalk with Solid Heat Carrier

    Directory of Open Access Journals (Sweden)

    Min Guo

    2015-05-01

    Full Text Available Pyrolysis of corn stalk with a solid heat carrier was studied under temperatures ranging from 430 to 620 °C. The solid heat carrier used was high-temperature ash from a CFB boiler. The yields of three products and their characteristics were investigated. Moreover, the distributions of sulfur and nitrogen in the products were determined. The results indicate that with increasing temperature, the char yield decreased, gas yield increased, and calorific value of the gas increased from 10.13 to 16.65 MJ/m3. The yield of bio-oil reached a maximum, 14.24 wt.%, at 510 °C. Light-oil in the bio-oil accounted for more than 69.12 wt.%. The elemental composition of the char and char ash were analyzed. The distribution of sulfur and nitrogen in the char decreased to 60.44 and 46.52 wt.%, respectively, depending on the raw materials used. These results provide basic data for the possible industrial application of corn stalk.

  18. The complete mitochondrial genome of the Antarctic stalked jellyfish, Haliclystus antarcticus Pfeffer, 1889 (Staurozoa: Stauromedusae

    Directory of Open Access Journals (Sweden)

    Hsing-Hui Li

    2016-06-01

    Full Text Available In present study, the complete mitogenome sequence of the Antarctic stalked jellyfish, Haliclystus antarcticus Pfeffer (Staurozoa: Stauromedusae has been sequenced by next-generation sequencing method. The assembled mitogenome comprises of 15,766 bp including 13 protein coding genes, 7 transfer RNAs, and 2 ribosomal RNA genes. The overall base of Antarctic stalked jellyfish constitutes of 26.5% for A, 19.6% for C, 19.8% for G, 34.1% for T and show 90% identity to Sessile Jelly, Haliclystus sanjuanensis, in the northeastern Pacific Ocean. The complete mitogenome of the Antarctic stalked jellyfish, contributes fundamental and significant DNA molecular data for further phylogeography and evolutionary analysis for seahorse phylogeny. The complete sequence was deposited in DBBJ/EMBL/GenBank under accession number KU947038.

  19. Prediction of postoperative diabetes insipidus using morphological hyperintensity patterns in the pituitary stalk on magnetic resonance imaging after transsphenoidal surgery for sellar tumors.

    Science.gov (United States)

    Hayashi, Yasuhiko; Kita, Daisuke; Watanabe, Takuya; Fukui, Issei; Sasagawa, Yasuo; Oishi, Masahiro; Tachibana, Osamu; Ueda, Fumiaki; Nakada, Mitsutoshi

    2016-12-01

    Diabetes insipidus (DI) remains a complication of transsphenoidal surgery (TSS) for sellar and parasellar tumors. Antidiuretic hormone (ADH) appears as hyper intensity (HI) in the pituitary stalk and the posterior lobe of the pituitary gland on T1-weighted magnetic resonance (MR) imaging. Its disappearance from the posterior lobe occurs with DI, indicating a lack of ADH. The appearance of HI in the pituitary stalk indicates disturbances in ADH transport. This retrospective study included 172 patients undergoing TSS for sellar tumors at our institute from 2006 to 2014. Sequential T1-weighted MR images without enhancement were evaluated for HI in the pituitary stalk and the posterior lobe to assess the localization of ADH before and at intervals after TSS. DI was assessed pre- and postoperatively. HI in the pituitary stalk showed the following morphology: (1) ovoid in the distal end of the pituitary stalk (group A), (2) linear in the distal part of the pituitary stalk (group B), (3) linear in the whole pituitary stalk (group C). Preoperative DI occurred in 6 patients (3.5 %) with no HI observed in the posterior lobe. Postoperative DI was transient in 82 patients (47.7 %), and permanent in 11 (6.4 %). One week after surgery, HI was absent in the posterior lobe in 74 patients (43.0 %), and present in the pituitary stalk in 99 patients (57.6 %); both were significantly correlated with postoperative DI (p < 0.001). The absence of HI in the posterior lobe (A, 48.9 %; B, 68.3 %; C, 92.3 %), persistence of DI (A, 3.7 days; B, 45.9 days; C, 20.5 months), and duration until HI recovery in the posterior lobe (A, 3.6 months; B, 6.8 months; C, 22.9 months) were greatest in group C, followed by group B, and then group A. Fourteen group A patients did not have postoperative DI despite having HI in the pituitary stalk and the posterior lobe. Four group C patients developed permanent DI with persistence HI in the pituitary stalk. HI in the pituitary stalk and its

  20. A Novel Hemp Seed Meal Protein Hydrolysate Reduces Oxidative Stress Factors in Spontaneously Hypertensive Rats

    Directory of Open Access Journals (Sweden)

    Abraham T. Girgih

    2014-12-01

    Full Text Available This report shows the antioxidant effects of a hemp seed meal protein hydrolysate (HMH in spontaneously hypertensive rats (SHR. Defatted hemp seed meal was hydrolyzed consecutively with pepsin and pancreatin to yield HMH, which was incorporated into rat feed as a source of antioxidant peptides. Young (8-week old SHRs were divided into three groups (8 rats/group and fed diets that contained 0.0%, 0.5% or 1.0% (w/w HMH for eight weeks; half of the rats were sacrificed for blood collection. After a 4-week washout period, the remaining 20-week old SHRs were fed for an additional four weeks and sacrificed for blood collection. Plasma total antioxidant capacity (TAC and superoxide dismutase (SOD, catalase (CAT and total peroxides (TPx levels were determined. Results showed that plasma TAC, CAT and SOD levels decreased in the older 20-week old SHRs when compared to the young SHRs. The presence of HMH in the diets led to significant (p < 0.05 increases in plasma SOD and CAT levels in both young and adult SHR groups; these increases were accompanied by decreases in TPx levels. The results suggest that HMH contained antioxidant peptides that reduced the rate of lipid peroxidation in SHRs with enhanced antioxidant enzyme levels and total antioxidant capacity.

  1. Mechanical characterisation of hybrid composite laminates based on basalt fibres in combination with flax, hemp and glass fibres manufactured by vacuum infusion

    International Nuclear Information System (INIS)

    Petrucci, R.; Santulli, C.; Puglia, D.; Sarasini, F.; Torre, L.; Kenny, J.M.

    2013-01-01

    Highlights: ► For the first time, hybrid laminates with three different fibres were produced. ► Concerns are confirmed on the brittleness of hybrid laminates with basalt fibre core. ► An optimal configuration (FHB) for flexural properties was singled out. ► Differences between tensile and flexural properties of hybrids were identified. ► In general, the specific mechanical properties of the hybrids are quite high. - Abstract: This work concerns the production by vacuum infusion and the comparison of the properties of different hybrid composite laminates, based on basalt fibre composites as the inner core, and using also glass, flax and hemp fibre laminates to produce symmetrical configurations, all of them with a 21–23% fibre volume, in an epoxy resin. The laminates have been subjected to tensile, three-point flexural and interlaminar shear strength tests and their fracture surfaces have been characterised by scanning electron microscopy. The mechanical performance of all the hybrid laminates appears superior to pure hemp and flax fibre reinforced laminates and inferior to basalt fibre laminates. Among the hybrids, the best properties are offered by those obtained by adding glass and flax to basalt fibre reinforced laminates. Scanning electron microscopy (SEM) observation of hybrid laminates showed the diffuse presence of fibre pull-out in hemp and flax fibre reinforced layers and a general trend of brittle failure

  2. Deactivation of tannins in raisin stalk by polyethylene glycol-600 ...

    African Journals Online (AJOL)

    6000) and urea on dry and organic matter digestibility (IVDMD and IVOMD, respectively) and gas production in vitro. Raisin stalk contained 8.6% crude protein, 85% dry matter, 7% ash, 13.95% total extractable phenol (TEPH) and 2.13% total ...

  3. Determination of cannabinoids in hemp nut products in Taiwan by HPLC-MS/MS coupled with chemometric analysis: quality evaluation and a pilot human study.

    Science.gov (United States)

    Chang, Chih-Wei; Tung, Chun-Wei; Tsai, Chin-Chuan; Wu, Yu-Tse; Hsu, Mei-Chich

    2017-06-01

    Hemp nuts are mature cannabis seeds obtained after shelling and that are commonly used in traditional Chinese medicine for treating functional constipation. In this work, we screened hemp nut products, classified them, and verified the legality of consuming them. A total of 18 products were purchased from Taiwan, China, and Canada. Validated high-performance liquid chromatography with tandem mass spectrometry methods were developed for analyzing the cannabinoid (i.e., Δ 9 -tetrahydrocannabinol (THC), cannabidiol (CBD), and cannabinol) content of the products and the concentration of urinary 11-nor-9-carboxy-THC. Chemometric techniques, namely hierarchical clustering analysis (HCA) and principal component analysis (PCA), were applied for rapidly classifying 11 concentrated powder products in Taiwan. A pilot human study comprising single and multiple administrations of a product with 1.5 µg/g of THC was conducted to examine the urinary 11-nor-9-carboxy-THC concentration. Through optimization of 3 2 full factorial design, using 60% isopropanol as the extraction solvent exhibited the highest yield of cannabinoids and was applied as the optimal condition in further analysis. The results of HCA and PCA on quality evaluation were in good agreement; however, the tested products possessed distinct CBD-to-THC ratios which ranged widely from 0.1:1 to 46.8:1. Particularly, the products with CBD-to-THC ratios higher than 1:1 were the majority in Taiwan. Our data suggested that all the tested hemp nut products met the Taiwan restriction criterion of 10 µg/g of THC. We propose a usual consumption amount of hemp nut products in Taiwan would unlikely to violate the cut-off point of 15 ng/mL of urinary 11-nor-9-carboxy-THC. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

  4. Identification of sources of resistance to anthracnose stalk rot in maize

    Directory of Open Access Journals (Sweden)

    Alessandro Nicoli

    Full Text Available ABSTRACT: Adoption of resistant cultivars is the primary measure used to control anthracnose stalk rot. The goal of this study was to identify maize-resistant genotypes to anthracnose stalk rot, which are similar to the hybrid 2B710. Experiments were performed at Embrapa Maize and Sorghum experimental fields in Brazil. The first experimental trial evaluated 234 maize lines as well as two commercials hybrids, BRS1010 (susceptible and 2B710 (resistant. Artificial inoculations were performed with a strain at the blister (R2 phase, and evaluation of disease severity was performed after 30 days. The second experimental trial evaluated 48 maize lines and hybrids, inoculated with two Colletotrichum graminicola strains. In the first trial, eight resistance groups were formed, and the last lines were more resistant, as was the hybrid 2B710, with values between 11.50% and 23.0% of severity. In the second trial, there was an interaction between the two factors, lines and isolates, and the lines often showed the same reaction features as those obtained in the first trial. However, the disease severity was higher for most lines, even when using other isolates. These lines with effective levels of resistance could be used in future studies of inheritance, in programs to develop hybrids, and to identify molecular markers associated with resistance to anthracnose stalk rot in maize.

  5. Corn stalk as matrix in decomposting toilet for treating urine and feces

    Science.gov (United States)

    Sintawardani, N.; Nilawati, D.; Astuti, J. T.

    2017-03-01

    Bio-Toilet technology (BT) which is appropriate for the habits of Indonesian people has been studied and developed. BT is a dry toilet technology commonly uses ligno-cellulosic waste materials as matrix to facilitate the growth of natural microbes. In aerobic condition, microbes degrade feces and urine. Mineral as the leftover of feces and urine, such as nitrogen (N), phosphorus (P), and potassium (K) remain in the rest of matrix waste. After certain period. matrix can be harvested and used as soil conditioner. BT uses much less water, mobile, and very useful to be applied in areas where water availability is limited. BT type with different capacities, user amounts and mixing systems has been developed using sawdust for matrix. Since corn stalk is categorized as useless and priceless waste, its application in BT is challenging. Performance of BT with corn stalk as matrix to degrade feces and urine of carnivore imitating the human waste was observed. BT M-15 manual mixing type with paddle was filled with chopped corn stalk as much as 45% of total volume. This BT was designed for 15 person as users per day if 80% reactor volume was filled with ligno-cellulosic matrix. It is assumed that 150 g of feces are discharged once per person/day and 1000 mL of urine 6-8 times per day. Start up process was made in the beginning to initialize the needed microbes in the reactor (matrix). The discharge of feces and urine were increased slowly and gradually the users were increased from 1 to 4 users per day. Performance of BT was indicated by the change in the pile that showed by moisture content, temperature and pH. C/N ratio in matrix decreased significantly from 43 to 17. This result showed that the corn stalk could be used as matrix in BT.

  6. Stalking on Campus: Ensuring Security with Rights and Liberties

    Science.gov (United States)

    Campbell, Julie; Longo, Peter J.

    2010-01-01

    College campuses are often perceived as idyllic communities. While there is much truth in such perceptions, not surprisingly there are many complicated issues on college campuses. Stalking is one such problem that seems to persist and thrive in the cloistered college setting. Campus safety efforts must temper security practices with civil rights…

  7. Pituitary stalk interruption syndrome presenting as short stature: a case report.

    Science.gov (United States)

    Ram, Nanik; Ali, Syed Ahsan; Hussain, Syed Zubair

    2014-12-19

    Pituitary stalk interruption syndrome is a rare congenital abnormality of the pituitary that is responsible for anterior pituitary deficiency. It is characterized by a classic triad of interrupted pituitary stalk, absent or ectopic posterior pituitary, and anterior pituitary hypoplasia or aplasia. Clinical presentation varies according to age. In adults it presents as short stature and anterior pituitary deficiency. Without early diagnosis and treatment, mortality and morbidity in these patients is high. Early diagnosis and treatment of this rare disease can prevent permanent short statue of the patient. We report the first case of pituitary stalk interruption syndrome from Pakistan. A 17-year-old Pakistani young man presented with short stature and underdeveloped secondary sexual characters. His siblings and parents were healthy, with normal height. An examination showed his blood pressure was 90/60 mmHg, and his height, weight, and body mass index were 142 cm, 34.5 kg, and 17.10 kg/m2, respectively. He had no hair growth on his face, axilla, or pubis. His testes were between 1 and 2 mL in size, with a 4 cm-at-stretch micropenis. His lab investigations showed that his thyroid stimulating hormone (TSH) was 8.58 uIU/mL (0.4 to 4.2), his free thyroid hormone level FT4 was 0.46 ng/dL (0.89 to 1.76), his prolactin was 21.1 ng/mL (3.0 to 14.7), and his baseline cortisol was 0.30 ug/dL (4.3 to 22.4). His cortisol level after 60 minutes of cosyntropin injection was 3.5 ug/dL (4.3 to 22.4), his insulin like growth factor IGF-1 was 31.56 ng/mL (247.3 to 481.7), his testosterone level was under 2.5 ng/dL (2 to 800), his follicle stimulating hormone FSH was 0.41 uIU/mL (0.0 to 10.0), and his leutinizing hormone LH was under 0.1 uIU/mL (1.2 to 7.8). His bone age was 10 years according to the Greulich and Pyle method, as shown by X-rays. The results from his pituitary magnetic resonance imaging scan were consistent with pituitary stalk interruption syndrome. We describe a young

  8. Mesoporous activated carbon from corn stalk core for lithium ion batteries

    Science.gov (United States)

    Li, Yi; Li, Chun; Qi, Hui; Yu, Kaifeng; Liang, Ce

    2018-04-01

    A novel mesoporous activated carbon (AC) derived from corn stalk core is prepared via a facile and effective method which including the decomposition and carbonization of corn stalk core under an inert gas atmosphere and further activation process with KOH solution. The mesoporous activated carbon (AC) is characterized by X-ray diffraction (XRD), Raman spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Brunauer-Emmett-Teller (BET) measurements. These biomass waste derived from activated carbon is proved to be promising anode materials for high specific capacity lithium ion batteries. The activated carbon anode possesses excellent reversible capacity of 504 mAh g-1 after 100 cycles at 0.2C. Compared with the unactivated carbon (UAC), the electrochemical performance of activated carbon is significantly improved due to its mesoporous structure.

  9. Interconnected carbon nanosheets derived from hemp for ultrafast supercapacitors with high energy.

    Science.gov (United States)

    Wang, Huanlei; Xu, Zhanwei; Kohandehghan, Alireza; Li, Zhi; Cui, Kai; Tan, Xuehai; Stephenson, Tyler James; King'ondu, Cecil K; Holt, Chris M B; Olsen, Brian C; Tak, Jin Kwon; Harfield, Don; Anyia, Anthony O; Mitlin, David

    2013-06-25

    We created unique interconnected partially graphitic carbon nanosheets (10-30 nm in thickness) with high specific surface area (up to 2287 m(2) g(-1)), significant volume fraction of mesoporosity (up to 58%), and good electrical conductivity (211-226 S m(-1)) from hemp bast fiber. The nanosheets are ideally suited for low (down to 0 °C) through high (100 °C) temperature ionic-liquid-based supercapacitor applications: At 0 °C and a current density of 10 A g(-1), the electrode maintains a remarkable capacitance of 106 F g(-1). At 20, 60, and 100 °C and an extreme current density of 100 A g(-1), there is excellent capacitance retention (72-92%) with the specific capacitances being 113, 144, and 142 F g(-1), respectively. These characteristics favorably place the materials on a Ragone chart providing among the best power-energy characteristics (on an active mass normalized basis) ever reported for an electrochemical capacitor: At a very high power density of 20 kW kg(-1) and 20, 60, and 100 °C, the energy densities are 19, 34, and 40 Wh kg(-1), respectively. Moreover the assembled supercapacitor device yields a maximum energy density of 12 Wh kg(-1), which is higher than that of commercially available supercapacitors. By taking advantage of the complex multilayered structure of a hemp bast fiber precursor, such exquisite carbons were able to be achieved by simple hydrothermal carbonization combined with activation. This novel precursor-synthesis route presents a great potential for facile large-scale production of high-performance carbons for a variety of diverse applications including energy storage.

  10. Effects of steam pretreatment and co-production with ethanol on the energy efficiency and process economics of combined biogas, heat and electricity production from industrial hemp

    Science.gov (United States)

    2013-01-01

    Background The study presented here has used the commercial flow sheeting program Aspen Plus™ to evaluate techno-economic aspects of large-scale hemp-based processes for producing transportation fuels. The co-production of biogas, district heat and power from chopped and steam-pretreated hemp, and the co-production of ethanol, biogas, heat and power from steam-pretreated hemp were analysed. The analyses include assessments of heat demand, energy efficiency and process economics in terms of annual cash flows and minimum biogas and ethanol selling prices (MBSP and MESP). Results Producing biogas, heat and power from chopped hemp has the highest overall energy efficiency, 84% of the theoretical maximum (based on lower heating values), providing that the maximum capacity of district heat is delivered. The combined production of ethanol, biogas, heat and power has the highest energy efficiency (49%) if district heat is not produced. Neither the inclusion of steam pretreatment nor co-production with ethanol has a large impact on the MBSP. Ethanol is more expensive to produce than biogas is, but this is compensated for by its higher market price. None of the scenarios examined are economically viable, since the MBSP (EUR 103–128 per MWh) is higher than the market price of biogas (EUR 67 per MWh). The largest contribution to the cost is the cost of feedstock. Decreasing the retention time in the biogas process for low solids streams by partly replacing continuous stirred tank reactors by high-rate bioreactors decreases the MBSP. Also, recycling part of the liquid from the effluent from anaerobic digestion decreases the MBSP. The production and prices of methane and ethanol influence the process economics more than the production and prices of electricity and district heat. Conclusions To reduce the production cost of ethanol and biogas from biomass, the use of feedstocks that are cheaper than hemp, give higher output of ethanol and biogas, or combined production with

  11. Magnetic resonance imaging of thickened pituitary stalk proceeding to langerhans cell histiocytosis in a child

    International Nuclear Information System (INIS)

    Halefoglu, A.M.

    2006-01-01

    Magnetic resonance imaging has shown isolated pituitary stalk thickening in certain cases of idiopathic or secondary central diabetes insipidus (Dl) due to infiltrative processes. We present a 4-year-old boy who was initially diagnosed as having central Dl. The MRI showed isolated pituitary stalk thickening with prominent homogeneous contrast enhancement. The remaining findings on MRI were within normal limits. The patient's personal and family history and laboratory and clinical findings were unremarkable; therefore, he was initially diagnosed as having idiopathic Dl. Since central Dl and isolated pituitary stalk thickening may be considered to be the first manifestations of Langerhans cell histiocytosis, we decided to follow up the patient. After 5 months, following the initial diagnosis, on skeletal X-ray survey, the patient did indeed develop multiple lytic skull lesions which, on biopsy, were histologically typical bone lesions of Langerhans cell histiocytosis. Copyright (2006) Blackwell Science Pty Ltd

  12. Ethanol and supercritical fluid extracts of hemp seed (Cannabis sativa L. increase gene expression of antioxidant enzymes in HepG2 cells

    Directory of Open Access Journals (Sweden)

    Sunghyun Hong

    2015-06-01

    Conclusions: In conclusion, the findings of our study demonstrated that the hemp seed effectively inhibited H2O2 mediated oxidative stress and may be useful as a therapeutic agent in preventing oxidative stress mediated diseases.

  13. Evidence of the most stretchable egg sac silk stalk, of the European spider of the year Meta menardi.

    Science.gov (United States)

    Lepore, Emiliano; Marchioro, Andrea; Isaia, Marco; Buehler, Markus J; Pugno, Nicola M

    2012-01-01

    Spider silks display generally strong mechanical properties, even if differences between species and within the same species can be observed. While many different types of silks have been tested, the mechanical properties of stalks of silk taken from the egg sac of the cave spider Meta menardi have not yet been analyzed. Meta menardi has recently been chosen as the "European spider of the year 2012", from the European Society of Arachnology. Here we report a study where silk stalks were collected directly from several caves in the north-west of Italy. Field emission scanning electron microscope (FESEM) images showed that stalks are made up of a large number of threads, each of them with diameter of 6.03 ± 0.58 µm. The stalks were strained at the constant rate of 2 mm/min, using a tensile testing machine. The observed maximum stress, strain and toughness modulus, defined as the area under the stress-strain curve, are 0.64 GPa, 751% and 130.7 MJ/m(3), respectively. To the best of our knowledge, such an observed huge elongation has never been reported for egg sac silk stalks and suggests a huge unrolling microscopic mechanism of the macroscopic stalk that, as a continuation of the protective egg sac, is expected to be composed by fibres very densely and randomly packed. The Weibull statistics was used to analyze the results from mechanical testing, and an average value of Weibull modulus (m) is deduced to be in the range of 1.5-1.8 with a Weibull scale parameter (σ(0)) in the range of 0.33-0.41 GPa, showing a high coefficient of correlation (R(2) = 0.97).

  14. Effect of alkali treatment on the physical and surface properties of Indian hemp fibers

    Science.gov (United States)

    Sangappa, Rao, B. Lakshmeesha; Asha, S.; Somashekar, R.

    2013-02-01

    The Plant fibers are rich in cellulose and they are a cheap, easily renewable source of fibers with the potential for polymer reinforcement. The presence of surface impurities and the large amount of hydroxyl groups make plant fibers less attractive for reinforcement of polymeric materials. Hemp (Cannabis Sativa L.) fibers were subjected to alkalization using 1N sodium hydroxide (NaOH). The structural properties and surface morphology of untreated and chemically modified fibers have been studied using X-ray diffraction (WAXS) and Scanning electron microscopy (SEM) respectively.

  15. Experimental characterization of thermal and hygric properties of hemp concrete with consideration of the material age evolution

    Science.gov (United States)

    Bennai, F.; Issaadi, N.; Abahri, K.; Belarbi, R.; Tahakourt, A.

    2018-04-01

    The incorporation of plant crops in construction materials offers very good hygrothermal performance to the building, ensuring substantial environmental and ecological benefits. This paper focuses on studying the evolution of hygrothermal properties of hemp concrete over age (7, 30 and 60 days). The analysis is done with respect to two main hygric and thermal properties, respectively: sorption isotherms, water vapor permeability, thermal conductivity and heat capacity. In fact, most of these parameters are very susceptible to change function of the age of the material. This influence of the aging is mainly due to the evolution of the microstructure with the binder hydration over time and the creation of new hydrates which can reduces the porosity of the material and consequently modify its properties. All the tested hemp concrete samples presented high moisture storage capacity and high-water vapor permeability whatever the age of such hygroscopic material. These hygric parameters increase significantly for high relative humidity requiring more consideration of such variability during the modeling of coupled heat and mass transfer within the material. By the same, the thermal conductivity and heat capacity tests highlighted the impact of the temperature and hygric state of the studied material.

  16. Study of Nutrient Content Variation in Bulb And Stalk of Onions ...

    African Journals Online (AJOL)

    acer

    Keywords: Onion bulbs and stalks, proximate, nutrient elements, vitamins A and C; oxalate. ... application of fertilizers, manure, compost and ..... iron products, the use of natural source of Fe such .... in Fish and Sediment from Kubanni River,.

  17. Thermal Stress and Heat Transfer Coefficient for Ceramics Stalk Having Protuberance Dipping into Molten Metal

    Science.gov (United States)

    Noda, Nao-Aki; Hendra; Li, Wenbin; Takase, Yasushi; Ogura, Hiroki; Higashi, Yusuke

    Low pressure die casting is defined as a net shape casting technology in which the molten metal is injected at high speeds and pressure into a metallic die. The low pressure die casting process plays an increasingly important role in the foundry industry as a low-cost and high-efficiency precision forming technique. In the low pressure die casting process is that the permanent die and filling systems are placed over the furnace containing the molten alloy. The filling of the cavity is obtained by forcing the molten metal, by means of a pressurized gas, to rise into a ceramic tube having protuberance, which connects the die to the furnace. The ceramics tube, called stalk, has high temperature resistance and high corrosion resistance. However, attention should be paid to the thermal stress when the stalk having protuberance is dipped into the molten aluminum. It is important to reduce the risk of fracture that may happen due to the thermal stresses. In this paper, thermo-fluid analysis is performed to calculate surface heat transfer coefficient. The finite element method is applied to calculate the thermal stresses when the stalk having protuberance is dipped into the crucible with varying dipping speeds. It is found that the stalk with or without protuberance should be dipped into the crucible slowly to reduce the thermal stress.

  18. Status of maize stalk rot complex in western belts of Nepal and its integrated management

    Directory of Open Access Journals (Sweden)

    Subash Subedi

    2016-12-01

    Full Text Available Maize stalk rot complex is becoming a serious threat for maize growing areas of Nepal. A field monitoring for maize stalk rot complex was done during crop season (August, 2016 covering 10 farmers field each of Surkhet, Banke, Dang, Chitwan and Nawalparasi districts. Maize crop showed highly susceptible reaction to the disease at western belts of Dang and susceptible reaction was marked in Chitwan and Nawalparasi districts while the disease effect was mild at Banke and Surkhet district. Most of the plant diseases managed successfully through the application of bio-control agents, host resistance, chemicals and other different cultural control methods. The result of field experiment conducted at Dang showed that all the treatments had significant (P≤0.05 effect on percent disease index (PDI and crop yield over farmers practice to control maize stalk rot. The higher percent disease control (52.36% and yield increase (40.29% were recorded from the plot sprayed with streptocyclin @ 2 g L-1 and insecticide (cypermethrin + chloropyrifos @ 2.5 ml L-1 of water during knee height and subsequent spray after 15 days interval as compared to farmers practice. Out of 30 genotypes, Rampur composit, Arun 2, Rampur 34, RamS03F08, TLBRS07F16 and Rampur 24 were found resistant against stalk rot complex with higher yield at Rampur Chitwan.

  19. Biochemical response and host-pathogen relation of stalk rot fungi ...

    African Journals Online (AJOL)

    Stalk rot is a destructive disease in maize caused by Fusarium and Macrophomina species. A study was carried out to understand the mode of infection, host biochemical response and comparison of inoculation techniques in Fusarium verticillioides and Macrophomina phaseolina in maize. In seed inoculation experiment, ...

  20. Effect of Fungal Deterioration on Physical and Mechanical Properties of Hemp and Flax Natural Fiber Composites

    Directory of Open Access Journals (Sweden)

    Bryn Crawford

    2017-10-01

    Full Text Available The development and application of bio-sourced composites have been gaining wide attention, yet their deterioration due to the growth of ubiquitous microorganisms during storage/manufacturing/in-service phases is still not fully understood for optimum material selection and design purposes. In this study, samples of non-woven flax fibers, hemp fibers, and mats made of co-mingled randomly-oriented flax or hemp fiber (50% and polypropylene fiber (50% were subjected to 28 days of exposure to (i no water-no fungi, (ii water only and (iii water along with the Chaetomium globosum fungus. Biocomposite samples were measured for weight loss over time, to observe the rate of fungal growth and the respiration of cellulose components in the fibers. Tensile testing was conducted to measure mechanical properties of the composite samples under different configurations. Scanning electron microscopy was employed to visualize fungal hyphal growth on the natural fibers, as well as to observe the fracture planes and failure modes of the biocomposite samples. Results showed that fungal growth significantly affects the dry mass as well as the tensile elastic modulus of the tested natural fiber mats and composites, and the effect depends on both the type and the length scale of fibers, as well as the exposure condition and time.

  1. Heathlands, fire and grazing. A palaeoenvironmental view of Las Hurdes (Cáceres, Spain history during the last 1200 years

    Directory of Open Access Journals (Sweden)

    Daniel Abel-Schaad

    2014-08-01

    Full Text Available Aim of study. The diachronic study of vegetation change through palynological analysis of sedimentary deposits is an essential tool both to design sound strategies on landscape  management and to understand its anthropogenic dynamics.Area of study. La Meseguera mire (Ladrillar, Cáceres, Spain is located in the Hurdes region in the western part of Iberian Central System and started to develop at the beginning of the Islamic period (ca. 770 cal AD, in an area widely dominated by heathland.  Material and methods. Pollen, non-pollen palynomorphs and charcoal accumulation rate (CHAR combined with historical data are useful indicators to assess the increasing role of human influence on vegetation.Main results. The use of fire and livestock husbandry represents the main drivers of landscape change in the course of the history. The establishment of forest afforestation plans, from the middle of 20th century, changed substantially the regional features. The sporadic presence of beech pollen is detected until 16th century, which implies the most western location in the Iberian Central Mountain System.Research highlights. The integration of pollen analysis and historical data is an essential tool when studying the changes in Holocene vegetation. These changes have been mainly driven by anthropogenic disturbances, more specifically by fire and livestock husbandry.Key Words: Anthropogenic dynamics; Central Mountain System; microcharcoals; non-pollen palynomorphs.  

  2. Stalk yield of sugarcane cultivars under different water regimes by subsurface drip irrigation

    Directory of Open Access Journals (Sweden)

    Aderson S. de Andrade Junior

    Full Text Available ABSTRACT This study aimed to evaluate the stalk yield of ten sugarcane cultivars (RB962962, RB931011, RB931530, RB98710, RB92579, RB867515, RB863129, SP791011, RB72545 and VAT90212 subjected to water deficit, full irrigation and water surplus by subsurface drip irrigation, during three cropping seasons (2011-2014. The experiment was conducted at the Experimental Field of Embrapa Meio-Norte, Teresina, Piauí State, Brazil, in dystrophic Red Yellow Argisol. The cultivars RB962962 (162.3 Mg ha-1 and RB867515 (158.5 Mg ha-1 have better stalk yield compared with other cultivars in all water regimes and cropping seasons.

  3. Phenolic Compounds Analysis of Root, Stalk, and Leaves of Nettle

    Directory of Open Access Journals (Sweden)

    Semih Otles

    2012-01-01

    Full Text Available Types of nettles (Urtica dioica were collected from different regions to analyze phenolic compounds in this research. Nettles are specially grown in the coastal part. According to this kind of properties, nettle samples were collected from coastal part of (Mediterranean, Aegean, Black sea, and Marmara Turkey. Phenolic profile, total phenol compounds, and antioxidant activities of nettle samples were analyzed. Nettles were separated to the part of root, stalk, and leaves. Then, these parts of nettle were analyzed to understand the difference of phenolic compounds and amount of them. Nettle (root, stalk and leaves samples were analyzed by using High-Performance Liquid Chromatography with Diode-Array Detection (HPLC-DAD to qualitative and quantitative determination of the phenolic compounds. Total phenolic components were measured by using Folin-Ciocalteu method. The antioxidant activity was measured by using DPPH (2,2-diphenyl-1-picrylhydrazyl which is generally used for herbal samples and based on single electron transfer (SET.

  4. Phenolic compounds analysis of root, stalk, and leaves of nettle.

    Science.gov (United States)

    Otles, Semih; Yalcin, Buket

    2012-01-01

    Types of nettles (Urtica dioica) were collected from different regions to analyze phenolic compounds in this research. Nettles are specially grown in the coastal part. According to this kind of properties, nettle samples were collected from coastal part of (Mediterranean, Aegean, Black sea, and Marmara) Turkey. Phenolic profile, total phenol compounds, and antioxidant activities of nettle samples were analyzed. Nettles were separated to the part of root, stalk, and leaves. Then, these parts of nettle were analyzed to understand the difference of phenolic compounds and amount of them. Nettle (root, stalk and leaves) samples were analyzed by using High-Performance Liquid Chromatography with Diode-Array Detection (HPLC-DAD) to qualitative and quantitative determination of the phenolic compounds. Total phenolic components were measured by using Folin-Ciocalteu method. The antioxidant activity was measured by using DPPH (2,2-diphenyl-1-picrylhydrazyl) which is generally used for herbal samples and based on single electron transfer (SET).

  5. Case of pituitary stalk transection syndrome ascertained after breech delivery.

    Science.gov (United States)

    Fukuta, Kaori; Hidaka, Takao; Ono, Yosuke; Kochi, Keiko; Yasoshima, Kuniaki; Arai, Takashi

    2016-02-01

    Pituitary stalk transection syndrome (PSTS) is a rare complication that can accompany breech delivery. Early diagnosis of this syndrome is difficult, and it may cause a serious delay in the diagnosis. We present a case of PSTS ascertained after breech delivery. A 20-year-old woman presented with primary amenorrhea. The patient was born by breech delivery and had a history of treatment for pituitary dwarfism. Her laboratory findings showed pituitary hypothyroidism, and hormone replacement therapy was initiated. At 28 years old, she became pregnant and had a normal delivery at 38 weeks' gestation. One year after delivery, her thyroid hormone level changed. Laboratory test showed adrenocortical insufficiency, and magnetic resonance imaging of the pituitary gland showed transection of the pituitary stalk and development of an ectopic posterior lobe. These findings were compatible with PSTS. When a patient who has been born by breech delivery presents with symptoms of pituitary deficiency, PSTS should be considered in the differential diagnosis. © 2015 Japan Society of Obstetrics and Gynecology.

  6. Phenolic Compounds Analysis of Root, Stalk, and Leaves of Nettle

    Science.gov (United States)

    Otles, Semih; Yalcin, Buket

    2012-01-01

    Types of nettles (Urtica dioica) were collected from different regions to analyze phenolic compounds in this research. Nettles are specially grown in the coastal part. According to this kind of properties, nettle samples were collected from coastal part of (Mediterranean, Aegean, Black sea, and Marmara) Turkey. Phenolic profile, total phenol compounds, and antioxidant activities of nettle samples were analyzed. Nettles were separated to the part of root, stalk, and leaves. Then, these parts of nettle were analyzed to understand the difference of phenolic compounds and amount of them. Nettle (root, stalk and leaves) samples were analyzed by using High-Performance Liquid Chromatography with Diode-Array Detection (HPLC-DAD) to qualitative and quantitative determination of the phenolic compounds. Total phenolic components were measured by using Folin-Ciocalteu method. The antioxidant activity was measured by using DPPH (2,2-diphenyl-1-picrylhydrazyl) which is generally used for herbal samples and based on single electron transfer (SET). PMID:22593694

  7. Anatomic Dissection of Arachnoid Membranes Encircling the Pituitary Stalk on Fresh, Non-Formalin-Fixed Specimens: Anatomoradiologic Correlations and Clinical Applications in Craniopharyngioma Surgery.

    Science.gov (United States)

    Ciappetta, Pasqualino; Pescatori, Lorenzo

    2017-12-01

    The anatomy of the arachnoid membranes and cisternal spaces around the pituitary stalk has not been yet exhaustively described and understood. In this study, we performed a detailed anatomic study on fresh, non-formalin-fixed cadavers of the arachnoid membranes encircling the pituitary stalk and correlate our anatomic findings with magnetic resonance imaging (MRI). Ten fresh, non-formalin-fixed, non-silicon-injected adult cadaveric heads were analyzed in this study. The membrane and cisterns that were studied for our study were as follows: 1) the diaphragma sellae and its dural components; 2) the basal arachnoid membrane; 3) the Liliequist membrane with its diencephalic and mesencephalic portion; 4) the medial carotid membrane; 5) the chiasmatic cistern; and 6) the pituitary stalk. MRI examinations of the sellar region were performed in 15 healthy volunteers (9 men, mean age 40 years; and 6 women mean age, 37 years) to visualize the arachnoid membrane encircling the pituitary stalk. MRI examinations were performed with a 3-T unit. A 3-dimensional constructive interference in steady state pulse magnetic resonance sequence was used. All the membranes examined were visualized clearly in all the dissections performed. Their 3-dimensional organization around the pituitary stalk was clarified and confirmed by MRI. Our study gives a detailed description of the pituitary stalk arachnoid sheets on fresh, non-formalin-fixed cadavers. This technique allowed us to clearly identify a funnel-shaped arachnoid collar encircling the pituitary stalk and delimiting a distinct cisternal space belonging to the stalk itself. Copyright © 2017 Elsevier Inc. All rights reserved.

  8. Steam explosion distinctively enhances biomass enzymatic saccharification of cotton stalks by largely reducing cellulose polymerization degree in G. barbadense and G. hirsutum.

    Science.gov (United States)

    Huang, Yu; Wei, Xiaoyang; Zhou, Shiguang; Liu, Mingyong; Tu, Yuanyuan; Li, Ao; Chen, Peng; Wang, Yanting; Zhang, Xuewen; Tai, Hongzhong; Peng, Liangcai; Xia, Tao

    2015-04-01

    In this study, steam explosion pretreatment was performed in cotton stalks, leading to 5-6 folds enhancements on biomass enzymatic saccharification distinctive in Gossypium barbadense and Gossypium hirsutum species. Sequential 1% H2SO4 pretreatment could further increase biomass digestibility of the steam-exploded stalks, and also cause the highest sugar-ethanol conversion rates probably by releasing less inhibitor to yeast fermentation. By comparison, extremely high concentration alkali (16% NaOH) pretreatment with raw stalks resulted in the highest hexoses yields, but it had the lowest sugar-ethanol conversion rates. Characterization of wall polymer features indicated that biomass saccharification was enhanced with steam explosion by largely reducing cellulose DP and extracting hemicelluloses. It also showed that cellulose crystallinity and arabinose substitution degree of xylans were the major factors on biomass digestibility in cotton stalks. Hence, this study has provided the insights into cell wall modification and biomass process technology in cotton stalks and beyond. Copyright © 2015 Elsevier Ltd. All rights reserved.

  9. Evidence of the most stretchable egg sac silk stalk, of the European spider of the year Meta menardi.

    Directory of Open Access Journals (Sweden)

    Emiliano Lepore

    Full Text Available Spider silks display generally strong mechanical properties, even if differences between species and within the same species can be observed. While many different types of silks have been tested, the mechanical properties of stalks of silk taken from the egg sac of the cave spider Meta menardi have not yet been analyzed. Meta menardi has recently been chosen as the "European spider of the year 2012", from the European Society of Arachnology. Here we report a study where silk stalks were collected directly from several caves in the north-west of Italy. Field emission scanning electron microscope (FESEM images showed that stalks are made up of a large number of threads, each of them with diameter of 6.03 ± 0.58 µm. The stalks were strained at the constant rate of 2 mm/min, using a tensile testing machine. The observed maximum stress, strain and toughness modulus, defined as the area under the stress-strain curve, are 0.64 GPa, 751% and 130.7 MJ/m(3, respectively. To the best of our knowledge, such an observed huge elongation has never been reported for egg sac silk stalks and suggests a huge unrolling microscopic mechanism of the macroscopic stalk that, as a continuation of the protective egg sac, is expected to be composed by fibres very densely and randomly packed. The Weibull statistics was used to analyze the results from mechanical testing, and an average value of Weibull modulus (m is deduced to be in the range of 1.5-1.8 with a Weibull scale parameter (σ(0 in the range of 0.33-0.41 GPa, showing a high coefficient of correlation (R(2 = 0.97.

  10. A comparison of soda and soda-AQ pulps from cotton stalks

    African Journals Online (AJOL)

    STORAGESEVER

    2009-11-16

    Nov 16, 2009 ... Duzce University, Faculty of Forestry, Konuralp Campus, 81620 Düzce, Turkey. ... two in Latin America and three in Africa and Middle East. (Casey, 1990). ... After that the cotton stalks were dried in the laboratory atmosphere, ...

  11. Ecological and physiological aspects of aestivation-diapause in the larvae of two Pyralid stalk borers of maize in Kenya

    NARCIS (Netherlands)

    Scheltes, P.

    1978-01-01

    Stalk borers are highly destructive to a large number of important graminaceous crops all over the world. Some examples of economically important stalk borers and a general description of their life-cycle are mentioned in chapter 1. In the same chapter difficulties in controlling the insects are

  12. Durability of Starch Based Biodegradable Plastics Reinforced with Manila Hemp Fibers

    Directory of Open Access Journals (Sweden)

    Shinji Ochi

    2011-02-01

    Full Text Available The biodegradability of Manila hemp fiber reinforced biodegradable plastics was studied for 240 days in a natural soil and 30 days in a compost soil. After biodegradability tests, weights were measured and both tensile strength tests and microscopic observation were performed to evaluate the biodegradation behavior of the composites. The results indicate that the tensile strength of the composites displays a sharp decrease for up to five days, followed by a gradual decrease. The weight loss and the reduction in tensile strength of biodegradable composite materials in the compost soil are both significantly greater than those buried in natural soil. The biodegradability of these composites is enhanced along the lower portion because this area is more easily attacked by microorganisms.

  13. Durability of Starch Based Biodegradable Plastics Reinforced with Manila Hemp Fibers.

    Science.gov (United States)

    Ochi, Shinji

    2011-02-25

    The biodegradability of Manila hemp fiber reinforced biodegradable plastics was studied for 240 days in a natural soil and 30 days in a compost soil. After biodegradability tests, weights were measured and both tensile strength tests and microscopic observation were performed to evaluate the biodegradation behavior of the composites. The results indicate that the tensile strength of the composites displays a sharp decrease for up to five days, followed by a gradual decrease. The weight loss and the reduction in tensile strength of biodegradable composite materials in the compost soil are both significantly greater than those buried in natural soil. The biodegradability of these composites is enhanced along the lower portion because this area is more easily attacked by microorganisms.

  14. Comparative Study of Root, Stalk and Leaf Essential Oils of ...

    African Journals Online (AJOL)

    MBI

    2017-03-03

    Mar 3, 2017 ... ABSTRACT. The root, stalk and leaf essential oils of Cymbopogon citratus grown in Kaduna, North Central Nigeria were extracted separately by hydrodistillation and characterized by GC-MS. The chemical composition analysis by. GC-MS of the oils allowed the identification of 34, 26 and 16 compounds ...

  15. Colchicine affects cell motility, pattern formation and stalk cell differentiation in Dictyostelium by altering calcium signaling.

    Science.gov (United States)

    Poloz, Yekaterina; O'Day, Danton H

    2012-04-01

    Previous work, verified here, showed that colchicine affects Dictyostelium pattern formation, disrupts morphogenesis, inhibits spore differentiation and induces terminal stalk cell differentiation. Here we show that colchicine specifically induces ecmB expression and enhances accumulation of ecmB-expressing cells at the posterior end of multicellular structures. Colchicine did not induce a nuclear translocation of DimB, a DIF-1 responsive transcription factor in vitro. It also induced terminal stalk cell differentiation in a mutant strain that does not produce DIF-1 (dmtA-) and after the treatment of cells with DIF-1 synthesis inhibitor cerulenin (100 μM). This suggests that colchicine induces the differentiation of ecmB-expressing cells independent of DIF-1 production and likely through a signaling pathway that is distinct from the one that is utilized by DIF-1. Depending on concentration, colchicine enhanced random cell motility, but not chemotaxis, by 3-5 fold (10-50 mM colchicine, respectively) through a Ca(2+)-mediated signaling pathway involving phospholipase C, calmodulin and heterotrimeric G proteins. Colchicine's effects were not due to microtubule depolymerization as other microtubule-depolymerizing agents did not have these effects. Finally normal morphogenesis and stalk and spore cell differentiation of cells treated with 10 mM colchicine were rescued through chelation of Ca2+ by BAPTA-AM and EDTA and calmodulin antagonism by W-7 but not PLC inhibition by U-73122. Morphogenesis or spore cell differentiation of cells treated with 50 mM colchicine could not be rescued by the above treatments but terminal stalk cell differentiation was inhibited by BAPTA-AM, EDTA and W-7, but not U-73122. Thus colchicine disrupts morphogenesis and induces stalk cell differentiation through a Ca(2+)-mediated signaling pathway involving specific changes in gene expression and cell motility. Copyright © 2011 International Society of Differentiation. Published by Elsevier B

  16. Modeling of kinetics of Cr(VI) sorption onto grape stalk waste in a stirred batch reactor

    International Nuclear Information System (INIS)

    Escudero, Carlos; Fiol, Nuria; Poch, Jordi; Villaescusa, Isabel

    2009-01-01

    Recently, Cr(VI) removal by grape stalks has been postulated to follow two mechanisms, adsorption and reduction to trivalent chromium. Nevertheless, the rate at which both processes take place and the possible simultaneity of both processes has not been investigated. In this work, kinetics of Cr(VI) sorption onto grape stalk waste has been studied. Experiments were carried out at different temperatures but at a constant pH (3 ± 0.1) in a stirred batch reactor. Results showed that three steps take place in the process of Cr(VI) sorption onto grape stalk waste: Cr(VI) sorption, Cr(VI) reduction to Cr(III) and the adsorption of the formed Cr(III). Taking into account the evidences above mentioned, a model has been developed to predict Cr(VI) sorption on grape stalks on the basis of (i) irreversible reduction of Cr(VI) to Cr(III) reaction, whose reaction rate is assumed to be proportional to the Cr(VI) concentration in solution and (ii) adsorption and desorption of Cr(VI) and formed Cr(III) assuming that all the processes follow Langmuir type kinetics. The proposed model fits successfully the kinetic data obtained at different temperatures and describes the kinetics profile of total, hexavalent and trivalent chromium. The proposed model would be helpful for researchers in the field of Cr(VI) biosorption to design and predict the performance of sorption processes.

  17. Organics and mineral fertilizers and biological control on the incidence of stalk rot and corn yield

    Directory of Open Access Journals (Sweden)

    Elena Blume

    2014-06-01

    Full Text Available The expansion of area under maize (Zea mays L. and the use of no tillage have favored the incidence of stalk rot on this crop. The study aimed to evaluate the organic fertilizers and the treatment of corn seeds with Trichoderma spp. on the production of dry matter (DM of shoot, incidence of stalk rot and corn yield. The experiment consisted in a factorial with split-plot in strips, on the randomized block design with four replicates, and the fertilization treatments (pig slurry; swine deep bedding; cattle slurry; mineral fertilizer; control treatment were applied to the plots and the seeds treatment (with and without Trichoderma spp. in the subplots. At the flowering stage, three corn plants per subplot were collected for the assessment of DM production. At physiological maturity stage, the incidence of stalk rot was assessed, and the ears of corn harvested for productivity assessment. The organic and mineral fertilizers increased the production of DM and productivity of corn. Trichoderma spp. increased the production of DM of corn, but had no reflection on productivity. The incidence of stalk rot in corn was higher in treatments with organic and mineral fertilization. Organic fertilizers increase dry matter production of shoot and corn yield, and Trichoderma spp. provides an increase in dry matter production of shoot.

  18. Effects of genetically modified cotton stalks on antibiotic resistance genes, intI1, and intI2 during pig manure composting.

    Science.gov (United States)

    Duan, Manli; Gu, Jie; Wang, Xiaojuan; Li, Yang; Zhang, Sheqi; Yin, Yanan; Zhang, Ranran

    2018-01-01

    Genetically modified (GM) cotton production generates a large yield of stalks and their disposal is difficult. In order to study the feasibility of using GM cotton stalks for composting and the changes that occur in antibiotic resistance genes (ARGs) during composting, we supplemented pig manure with GM or non-GM cotton stalks during composting and we compared their effects on the absolute abundances (AA) of intI1, intI2, and ARGs under the two treatments. The compost was mature after processing based on the germination index and C/N ratio. After composting, the AAs of ARGs, intI1, and intI2 were reduced by 41.7% and 45.0% in the non-GM and GM treatments, respectively. The ARG profiles were affected significantly by temperature and ammonia nitrogen. In addition, excluding tetC, GM cotton stalks had no significant effects on ARGs, intI1, and intI2 compared with the non-GM treatment (p composting with livestock manure, and the AAs of ARGs can be reduced. Furthermore, the results of this study provide a theoretical basis for the harmless utilization of GM cotton stalks. Copyright © 2017 Elsevier Inc. All rights reserved.

  19. Is nectar reabsorption restricted by the stalk cells of floral and extrafloral nectary trichomes?

    Science.gov (United States)

    Cardoso-Gustavson, P; Davis, A R

    2015-01-01

    Reabsorption is a phase of nectar dynamics that occurs concurrently with secretion; it has been described in floral nectaries that exude nectar through stomata or unicellular trichomes, but has not yet been recorded in extrafloral glands. Apparently, nectar reabsorption does not occur in multicellular secretory trichomes (MST) due to the presence of lipophilic impregnations - which resemble Casparian strips - in the anticlinal walls of the stalk cells. It has been assumed that these impregnations restrict solute movement within MST to occur unidirectionally and exclusively by the symplast, thereby preventing nectar reflux toward the underlying nectary tissues. We hypothesised that reabsorption is absent in nectaries possessing MST. The fluorochrome lucifer yellow (LYCH) was applied to standing nectar of two floral and extrafloral glands of distantly related species, and then emission spectra from nectary sections were systematically analysed using confocal microscopy. Passive uptake of LYCH via the stalk cells to the nectary tissues occurred in all MST examined. Moreover, we present evidence of nectar reabsorption in extrafloral nectaries, demonstrating that LYCH passed the stalk cells of MST, although it did not reach the deepest nectary tissues. Identical (control) experiments performed with neutral red (NR) demonstrated no uptake of this stain by actively secreting MST, whereas diffusion of NR did occur in plasmolysed MST of floral nectaries at the post-secretory phase, indicating that nectar reabsorption by MST is governed by stalk cell physiology. Interestingly, non-secretory trichomes failed to reabsorb nectar. The role of various nectary components is discussed in relation to the control of nectar reabsorption by secretory trichomes. © 2014 German Botanical Society and The Royal Botanical Society of the Netherlands.

  20. Size reduction of high- and low-moisture corn stalks by linear knife grid system

    Energy Technology Data Exchange (ETDEWEB)

    Igathinathane, C. [Agricultural and Biological Engineering Department, 130 Creelman Street, Mississippi State University, Mississippi State, Mississippi 39762 (United States); Womac, A.R. [Department of Biosystems Engineering and Soil Science, 2506 E. J. Chapman Drive, The University of Tennessee, Knoxville, Tennessee 37996 (United States); Sokhansanj, S. [Oak Ridge National Laboratory, Environmental Sciences Division, Oak Ridge, P. O. Box 2008, Tennessee 37831 (United States); Narayan, S. [First American Scientific Company, 100 Park Royal South West Vancouver, British Columbia, V7T 1A2 (Canada)

    2009-04-15

    High- and low-moisture corn stalks were tested using a linear knife grid size reduction device developed for first-stage size reduction. The device was used in conjunction with a universal test machine that quantified shearing stress and energy characteristics for forcing a bed of corn stalks through a grid of sharp knives. No published engineering performance data for corn stover with similar devices are available to optimize performance; however, commercial knife grid systems exist for forage size reduction. From the force-displacement data, mean and maximum ultimate shear stresses, cumulative and peak mass-based cutting energies for corn stalks, and mean new surface area-based cutting energies were determined from 4-5 refill runs at two moisture contents (78.8% and 11.3% wet basis), three knife grid spacings (25.4, 50.8, and 101.6 mm), and three bed depths (50.8, 101.6, and 152.4 mm). In general, the results indicated that peak failure load, ultimate shear stress, and cutting energy values varied directly with bed depth and inversely with knife grid spacing. Mean separation analysis established that high- and low-moisture conditions and bed depths {>=} 101.6 mm did not differ significantly (P < 0.05) for ultimate stress and cutting energy values, but knife grid spacing were significantly different. Linear knife grid cutting energy requirements for both moisture conditions of corn stalks were much smaller than reported cutting energy requirements. Ultimate shear stress and cutting energy results of this research should aid the engineering design of commercial scale linear knife gird size reduction equipment for various biomass feedstocks. (author)

  1. Enhanced ethanol production from stalk juice of sweet sorghum by ...

    African Journals Online (AJOL)

    Sweet sorghum (sugar sorghum, Sorghum bicolor) is one kind of non-grain energy crops. As a novel green regenerated high-energy crop with high utility value, high yield of biomass, the sweet sorghum is widely used and developed in China. Stalk juice of sweet sorghum was used as the main substrate for ethanol ...

  2. Stalking the ultimate particle

    CERN Multimedia

    2003-01-01

    If you missed the ARTE programme entitled "L'Ultime Particule" broadcast in February, you have another chance to catch it in CERN's Main Auditorium on 13 March. "L'Ultime Particule" is a documentary by the French director Michel Andrieu that seeks to explain particle physics through a contemplative quest for the research physicists of matter of today and yesteryear. Invariably kitted out in a red parka and a soft hat, the programme's investigator scours the planet and the archives in search of the research physicists who are stalking the ultimate particle, the Higgs boson, in their quest to understand the structure of matter. Naturally enough, CERN is an important stage of his journey where Michel Andrieu and his team spent several days last year. Both from the physics and metaphysical points of view, "L'Ultime Particule" is worth seeing. The film's director, Michel Andrieu, will introduce his documentary and answer questions from the audience after the documentary has been shown. L'Ultime Particule by Mic...

  3. Synergistic effect on co-pyrolysis of capsicum stalks and coal | Niu ...

    African Journals Online (AJOL)

    With the depletion of fossil fuel and the concern about environmental issues, the utilization of biomass resources has attracted increasing worldwide interest. The pyrolysis behavior of capsicum stalks and Baoji coal mixtures was investigated by TG-DSC. Results show that the thermal degradation temperature range of ...

  4. Exploring of Agro Waste (Pineapple Leaf, Corn Stalk, and Napier Grass) by Chemical Composition and Morphological Study

    OpenAIRE

    Angzzas Sari Mohd Kassim; Halizah Awang; Ashuvila Mohd Aripin

    2013-01-01

    Malaysia is a country that is a rich source of agricultural waste material. Three different crops were studied here, including pineapple (Ananas comosus) leaf, corn (Zea mays) stalk, and Napier grass (Pennisetum purpureum). These crops are characterized as agricultural waste materials in Malaysia and have a high potential to be used as alternative fibers for the paper making industry. The objective of this work was to analyze the chemical composition of pineapple leaf, corn stalk, and Napier ...

  5. A brief account of the fractions of soma.

    Science.gov (United States)

    Mahdihassan, S

    1990-04-01

    Soma was originally Sauma as the Sanskrit form of the Avesta name Haoma. It is a loan word from the Chinese term, Hao-Ma, fire coloured hempior fibrous items like hemp and also coloured yellow with a tinge of brown. The Aryans as hunters took its juice as anti-fatigue drink. It was extolled as panacea and even as drink of longevity. The plant and its stalks were crushed between stones to produce juice. There arose different fractions and these have been given in a regular chart here.

  6. Recovery from diabetes insipidus and preservation of thyroid function after craniopharyngioma removal and pituitary stalk sectioning.

    Science.gov (United States)

    Ogawa, Yoshikazu; Niizuma, Kuniyasu; Tominaga, Teiji

    2017-11-01

    Craniopharyngioma is a slow-growing tumor, but long-term tumor control with maintenance of quality of life is sometimes very difficult to achieve, and hypothalamic disturbance should be strictly avoided in the treatment. However, management of the pituitary gland and/or pituitary stalk varies among surgeons and institutions. This retrospective review identified 44 patients, 24 males and 20 females with craniopharyngiomas who were initially treated by surgery through the extended transsphenoidal approach with pituitary stalk sectioning at a single institute. If the tumor bed involved the posterior lobe of the pituitary gland, pituitary stalk, anterior and/or mid portion of the third ventricle floor, these structures were removed en-bloc together with the tumor. The closest attention was paid to preserve fine arteries running along the surface of optic chiasm and the lateral walls of the third ventricle. Surgical outcome and changes in postoperative endocrinological status were investigated. Gross total removal was achieved in 40 of 44 patients (91%), and all patients could discharge without autonomic and/or thermal disturbances. Tumor remnants were identified with tight adhesion to the perforating arteries in 2 cases, tight adhesion to mammillary bodies in 1, and optic chiasm in 1. Administration of anti-diuretic hormone could be discontinued in 23 of 44 patients (52.3%) with improved diabetes insipidus (DI), although no patient could discontinue glucocorticoid administration. Preservation of thyroid function was achieved in another 23 of 44 patients (52.3%), and recovery from DI was correlated with preservation of thyroid function (p=0.016). Pituitary dysfunction is partially reversible even with pituitary stalk sectioning. Regrowth of tumor in the anterior and/or mid portion of the third ventricle floor including pituitary stalk can possibly be prevented by aggressive tumor removal, and co-achievement of long-term tumor control with maintenance of quality of life

  7. Candidate gene association mapping of Sclerotinia stalk rot resistance in sunflower (Helianthus annuus L.) uncovers the importance of COI1 homologs.

    Science.gov (United States)

    Talukder, Zahirul I; Hulke, Brent S; Qi, Lili; Scheffler, Brian E; Pegadaraju, Venkatramana; McPhee, Kevin; Gulya, Thomas J

    2014-01-01

    Functional markers for Sclerotinia basal stalk rot resistance in sunflower were obtained using gene-level information from the model species Arabidopsis thaliana. Sclerotinia stalk rot, caused by Sclerotinia sclerotiorum, is one of the most destructive diseases of sunflower (Helianthus annuus L.) worldwide. Markers for genes controlling resistance to S. sclerotiorum will enable efficient marker-assisted selection (MAS). We sequenced eight candidate genes homologous to Arabidopsis thaliana defense genes known to be associated with Sclerotinia disease resistance in a sunflower association mapping population evaluated for Sclerotinia stalk rot resistance. The total candidate gene sequence regions covered a concatenated length of 3,791 bp per individual. A total of 187 polymorphic sites were detected for all candidate gene sequences, 149 of which were single nucleotide polymorphisms (SNPs) and 38 were insertions/deletions. Eight SNPs in the coding regions led to changes in amino acid codons. Linkage disequilibrium decay throughout the candidate gene regions declined on average to an r (2) = 0.2 for genetic intervals of 120 bp, but extended up to 350 bp with r (2) = 0.1. A general linear model with modification to account for population structure was found the best fitting model for this population and was used for association mapping. Both HaCOI1-1 and HaCOI1-2 were found to be strongly associated with Sclerotinia stalk rot resistance and explained 7.4 % of phenotypic variation in this population. These SNP markers associated with Sclerotinia stalk rot resistance can potentially be applied to the selection of favorable genotypes, which will significantly improve the efficiency of MAS during the development of stalk rot resistant cultivars.

  8. Modification of Sorghum Starch-Cellulose Bioplastic with Sorghum Stalks Filler

    Directory of Open Access Journals (Sweden)

    Yuli Darni

    2017-05-01

    Full Text Available This study evaluated the feasibility of bioplastics production by various ratio of sorghum starch and cellulose from red seaweed Eucheuma spinossum, and the use of glycerol as plasticizer and sorghum stalks as filler. Solid-liquid matrix transition should be far over the operating temperature of gelatinization and extracted at 95oC in order to avoid the loss of conductivity. The analyzed variables were starch and cellulose seaweed Eucheuma spinossum and the addition of variation of filler. Sorghum stalk could be expected to affect the mechanical and physical properties of bioplastics. A thin sheet of plastic (plastic film was obtained as a result that have been tested mechanically to obtain the best condition for the formulation of starch-cellulose 8.5:1.5 (g/g. From the result of morphological studies, the fillers in the mixture composites were more randomly in each product and the addition of filler can increase mechanical properties of bioplastics. Chemical modification had a major effect on the mechanical properties. The phenomena of degradation and thermoplasticization were visible at chemical changes that can be observed in FTIR spectrum test results.

  9. Effect of Piper betel leaf stalk extract on protein metabolism in reproductive tissues of male albino rats

    OpenAIRE

    V Vengaiah; A Govardhan Naik; C Changamma

    2015-01-01

    Objective: To know the impact of Piper betel leaf stalk (P. betel) extract on Protein and energy metabolism and its role in male albino rats. Methods: Healthy adult (3-4 months old) male Wistar strain albino rats were administered with betel leaf stalk extract, at the dose of 50 mg/kg/day through oral gavages for 15 days. Twenty four hours after the last dose, the animals were autopsied. In order to assess antifertility effect in testis, epididymis, seminal vesicle and prostate gland, esti...

  10. Effect of Different Parts (Leaf, Stem and Stalk) and Seasons (Summer and Winter) on the Chemical Compositions and Antioxidant Activity of Moringa oleifera

    Science.gov (United States)

    Shih, Ming-Chih; Chang, Cheng-Ming; Kang, Sue-Ming; Tsai, Min-Lang

    2011-01-01

    Moringa oleifera, Lam. (Moringaceae) is grown world-wide in the tropics and sub-tropics of Asia and Africa and contains abundant various nutrients. This study describes the effect of different parts (leaf, stem and stalk) and seasons (summer and winter) on the chemical compositions and antioxidant activity of M. oleifera grown in Taiwan. The results showed that the winter samples of Moringa had higher ash (except the stalk part), calcium and phenolic compounds (except the leaf part) and stronger antioxidative activity than summer samples. The methanolic extract of Moringa showed strong scavenging effect of DPPH radicals and reducing power. The trend of antioxidative activity as a function of the part of Moringa was: leaf > stem > stalk for samples from both seasons investigated. The Moringa extract showed strong hydrogen peroxide scavenging activity and high Superoxide Dismutase (SOD) activity except the stalk part. PMID:22016645

  11. Adsorption of hexavalent chromium on modified corn stalk using different cross-linking agents

    Science.gov (United States)

    Chen, Suhong; Zhu, Yi; Han, Zhijun; Feng, Gao; Jia, Yuling; Fu, Kaifang; Yue, Qinyan

    2017-12-01

    In this study, four different types of adsorbents modified from corn stalk were synthesized after the reaction with epichlorohydrin, N,N-dimethylformamide, triethylamine and different cross-linking agents. The surface functional groups and thermal stability of modified corn stalk (MCSs) were characterized using FTIR and TG analysis, respectively. The feasibility of using MCSs to remove Cr(VI) were evaluated. Adsorption isotherms were determined and modeled with Langmuir, Freundlich and Temkin equations. The experimental results showed that MCS modified using diethylenetriamine (DETA) had the best modification effect, and the adsorption capacity of Cr(VI) reached as high as 227.27 mg/g at 323 K. Thermodynamic study showed that the Cr(VI) adsorption onto MCSs was endothermic processes. As a result, MCS by using DETA as cross-linking agent has good potential for the removal of Cr(VI) from aqueous solutions.

  12. Association of Expanded Disability Status Scale and Cytokines after Intervention with Co-supplemented Hemp Seed, Evening Primrose Oils and Hot-natured Diet in Multiple Sclerosis Patients

    Directory of Open Access Journals (Sweden)

    Behzad Baradaran

    2013-02-01

    Full Text Available Introduction: Multiple sclerosis (MS is an inflammatory demyelinating disease of the central nervous system (CNS. Because of limited efficacy and adverse side effects, identifying novel therapeutic and protective agents is important. The aim of this study is to examine the correlations between expanded disability status scale (EDSS and cytokines after intervention with co-supplemented hemp seed and evening primrose oils and hot-natured diet in patients with relapsing-remitting multiple sclerosis (RRMS. Methods: We studied a group of 23 patients with clinically definite RRMS, with EDSS<6 who received co-supplemented hemp seed and evening primrose oils with advising hot-natured diet. Clinically EDSS and immunological factors (plasma cytokines of IL-4, IFN-γ and IL-17 were assessed at baseline and after 6 months. Results: Mean follow-up was 180±2.9 days (N=23, 7 Male and 16 Females aged 25.0±7.5 years with disease duration 6.26±3.9 years. After 6 months, significant improvements in extended disability status score were found in the patients in agreement with decrease cytokines of IFN-γ and IL-17 and increase cytokines of IL-4. Clinical and immunological parameters showed improvement in the patients after the intervention. Conclusion: Our study shows that co-supplemented hemp seed and evening primrose oils with hot-natured diet can have beneficial effects in improving clinical symptoms in relapsing remitting MS patients and significant correlation was found between EDSS and immunological findings.

  13. CHARACTERISTICS OF CORN STALK HEMICELLULOSE PYROLYSIS IN A TUBULAR REACTOR

    OpenAIRE

    Gao-Jin Lv; Shu-Bin Wu; Rui Lou

    2010-01-01

    Pyrolysis characteristics of corn stalk hemicellulose were investigated in a tubular reactor at different temperatures, with focus mainly on the releasing profiles and forming behaviors of pyrolysis products (gas, char, and tar). The products obtained were further identified using various approaches (including GC, SEM, and GC-MS) to understand the influence of temperature on product properties and compositions. It was found that the devolatilization of hemicellulose mainly occurred at low tem...

  14. Co-composting of two-phase olive-mill pomace and poultry manure with tomato harvest stalks.

    Science.gov (United States)

    Sülük, Kemal; Tosun, İsmail; Ekinci, Kamil

    2017-04-01

    In this study, two-phase olive-mill pomace with poultry manure and chopped tomato harvest stalks were composted at different initial carbon/nitrogen (C/N) ratios with fixed free air space of 35%. Composting experiment was carried out in the 15 aerobic reactors made of stainless steel and was monitored for 28 days. During the composting process, temperature, moisture content, organic matter (OM), pH, electrical conductivity, oxygen and carbon dioxide concentrations, total carbon, total nitrogen, ammonium nitrogen ([Formula: see text]), nitrate nitrogen ([Formula: see text]), and total phosphorus were monitored. Compost mass and volume changes were determined at the beginning, during remixings, and at the end of composting. While the stabilization period took less time for the mixtures containing a high amount of poultry manure, the mixtures having the high portion of two-phase olive-mill pomace took a longer time due to the structure of olive stone and its lignin content. Dry matter loss (range: 18.1-34.0%.) in the mixtures increased with an increase in the share of poultry manure and tomato stalks in the initial mixture. OM loss (range: 21.7-46.1%) for tomato stalks (measured separately) during composting increased due to an increase in the ratio of poultry manure in the initial mixtures.

  15. Extraction and HPLC analysis of phenolic compounds in leaves, stalks, and textile fibers of Urtica dioica L.

    Science.gov (United States)

    Pinelli, Patrizia; Ieri, Francesca; Vignolini, Pamela; Bacci, Laura; Baronti, Silvia; Romani, Annalisa

    2008-10-08

    In the present study the phenolic composition of leaves, stalks, and textile fiber extracts from Urtica dioica L. is described. Taking into account the increasing demand for textile products made from natural fibers and the necessity to create sustainable "local" processing chains, an Italian project was funded to evaluate the cultivation of nettle fibers in the region of Tuscany. The leaves of two nettle samples, cultivated and wild (C and W), contain large amounts of chlorogenic and 2- O-caffeoylmalic acid, which represent 71.5 and 76.5% of total phenolics, respectively. Flavonoids are the main class in the stalks: 54.4% of total phenolics in C and 31.2% in W samples. Anthocyanins are second in quantitative importance and are present only in nettle stalks: 28.6% of total phenolics in C and 24.4% in W extracts. Characterization of phenolic compounds in nettle extracts is an important result with regard to the biological properties (antioxidant and antiradical) of these metabolites for their possible applications in various industrial activities, such as food/feed, cosmetics, phytomedicine, and textiles.

  16. [Detection method for the ability of hemp (Cannabis sativa L.) seed germination by the use of 2,3,5-triphenyl-2H-tetrazolium chloride (TTC)].

    Science.gov (United States)

    Ogata, Jun; Kikura-Hanajiri, Ruri; Yoshimatsu, Kayo; Kiuchi, Fumiyuki; Goda, Yukihiro

    2008-11-01

    Cannabis plants show a high Delta9-tetrahydrocannabinol content and are used as a psychoactive drug. Therefore the cultivation of hemp and its possession are prohibited by law in Japan. Meanwhile, Cannabis seeds have been used as a component of shichimi-togarashi (a Japanese spice), bird feed, or a crude drug (mashinin). To exclude the possibility of germination, it is officially noticed that hemp seeds must be killed. However, the number of violators has increased in recent years. To judge the ability of seed germination, a germination test is performed. However, the test requires several days and thus has not been used for on-site inspection. In this study, we developed a rapid detection method to determine the ability of Cannabis seeds to germinate using 2,3,5-triphenyl-2H-tetrazolium chloride (TTC). The principle of the assay is as follows. The endogenous respiratory enzymes in hemp seeds convert added colorless TTC into red 1,3,5-triphenylformazan. Consequently, a living embryo is stained red, while red does not appear in the dead seeds. The reaction was active over a pH range of 8.0-9.0, and the optimum activity was found from 40 to 50 degrees C. Under the optimum conditions, we were able to determine the ability of seeds to germinate based on the presence of color within 20 min. Since this method is rapid and simple, it is applicable to on-site inspections. In addition, it could be used as an alternative technique to the germination test, because erroneous decisions is cannot occur under the assay principle.

  17. A study on the chopping and mixing of cotton stalks with soil

    African Journals Online (AJOL)

    USER

    2010-07-26

    Jul 26, 2010 ... INTRODUCTION ... porating plant residues into soil reduces the risk of soil ... stalks into soil increases the productivity of the field. ... producers were asked about the total area of their agricultural fields .... are made of forged steel in one piece. ... maintenance works such as thinning, weeding and irrigation.

  18. Body Stalk Syndrome: A Curiosity

    Directory of Open Access Journals (Sweden)

    Anita Javalgi

    2014-07-01

    Full Text Available Limb body wall complex (LBWC /Body stalk syndrome anomaly refers to a rare complicated polymalformative fetal malformation syndrome of uncertain etiology firstly described by Van Allen et al in 1987. There are very few cases reported in literature and thus we report a rare case of LBWC. Twenty seven years female presented to labour room with 32 weeks of gestation with no prenatal care and delivered a low birth weight still born fetus weighing 1100gms. On fetal autopsy large abdominal wall defect was noted with difficulty in identifying abdomino-pelvic organs and ambiguous genitalia. Placenta weighed 250gms with attached short umbilical cord measuring 7cms, arising from periphery. A cyst noted attached to placental membrane measuring 9x5cms which on dissection retrieved partially maldeveloped organs. Post mortem radiological findings included Absence of right femur with short tibia and right fibula, Complex vestibral malformation, Craniosynostosis and Overcrowding of ribs.

  19. Fracture line index of fibular stalk and the ankle joint bone in the classification of the ankle joint trauma

    International Nuclear Information System (INIS)

    Wu Jun; Zhang Qiang

    2003-01-01

    Objective: To evaluate the fracture line index of fibular stalk and the ankle joint bone in the classification of the ankle joint trauma. Methods: Measure fracture line index of fibular stalk and the ankle joint in 217 adult cases of fracture and dislocation of ankle joint. And the cases were classified by the results of the measurement. Results: Measurement was unavailable in 9 cases of tearing fracture. In 31 cases, the lesions could not be particularly classified. And in the rest 176 cases the trauma were precisely classified. The over all successful rate was 81.6%. Conclusion: Fracture line index of fibular stalk and the ankle joint bone are valuable in classification of the trauma of the angle joint. While the specificity of this method is low in differentiating the adducting and abducting fracture of the medial angle, in which a combined investigation is recommended

  20. Effects of fistular onion stalk extract on the level of NO and ...

    African Journals Online (AJOL)

    user

    2011-03-28

    Mar 28, 2011 ... In this study, we investigated the effects of fistular onion stalk extracts on nitric oxide ... and flavonoids in onion (Knekt et al., 1996). ... cells lie between blood flow and smooth muscle cells. ... strated by a reduction in the blood vessel dilation factors .... raw onion inhibits platelet-mediated thrombosis in dogs.

  1. Phenolic Compounds Analysis of Root, Stalk, and Leaves of Nettle

    OpenAIRE

    Otles, Semih; Yalcin, Buket

    2012-01-01

    Types of nettles (Urtica dioica) were collected from different regions to analyze phenolic compounds in this research. Nettles are specially grown in the coastal part. According to this kind of properties, nettle samples were collected from coastal part of (Mediterranean, Aegean, Black sea, and Marmara) Turkey. Phenolic profile, total phenol compounds, and antioxidant activities of nettle samples were analyzed. Nettles were separated to the part of root, stalk, and leaves. Then, these parts ...

  2. Development of methods and systems for preparing hydrolyzates for acetone-butanol fermentation

    Energy Technology Data Exchange (ETDEWEB)

    Nakhmanovich, B M

    1967-01-01

    Optimal conditions for hydrolysis of vegetable waste material, e.g., maize stalks, sunflower parings, and hemp wastes, with concentrated or dilute H/sub 2/SO/sub 4/ were established. Hydrolyzates were neutralized with Ca(OH)/sub 2/ to pH 5.5 to 6.0 and the supernatant was sterilized at 110 to 115/sup 0/ for 15 to 20 minutes and used for fermentation in mixtures with molasses or mash. The maximum amount of fermentation inhibitors which can be present in hydrolyzate is: 0.1% furfural, 0.03% HCO/sub 2/H and 0.001% As.

  3. Rapid stalk elongation in tulip (Tulipa gesneriana L. cv. Apeldoorn) and the combined action of cold-induced invertase and the water-channel protein gammaTIP.

    Science.gov (United States)

    Balk, P A; de Boer, A D

    1999-09-01

    Many bulbous plants need a low-temperature treatment for flowering. Cold, for example, affects the elongation of the stalk, thereby influencing the quality of the cut flower. How the elongation of the stalk is promoted by cold and which physiological and biochemical mechanisms are involved have remained obscure. As invertase has been shown to be involved in the cold-induced elongation of the flower stalks of tulips (Lambrechts et al., 1994, Plant Physiol 104: 515-520), we further characterized this enzyme by cloning the cDNA and analysing its expression in various tissues of the tulip (Tulipa gesneriana L. cv. Apeldoorn) stalk. In addition, the role of sucrose synthase was investigated. Since turgor pressure is an important force driving cell elongation, the role of a water-channel protein (gammaTIP) was studied in relation to these two enzymes. The mRNA level of the invertase found was substantially up-regulated as a result of cold treatment. Analysis of the amino acid sequence of this invertase revealed the presence of a vacuolar targeting signal. Two different forms of sucrose synthase were found, the expression of one of them appeared to be restricted to the vascular tissue while the other form was present in the surrounding tissue. Both sucrose synthases were present in the stalk during the entire period of bulb storage and after planting, but their activities declined during stalk elongation. The expression of the gammaTIP gene was restricted mainly to the vascular tissue and its expression profile was identical to that of invertase. Simultaneous expression of invertase and gammaTIP possibly leads to an increase in osmotic potential and vacuolar water uptake, thus providing a driving force for stretching the stalk cells.

  4. Maize Cob Rot in Kenya and Its Association with Stalk Borer Damage

    International Nuclear Information System (INIS)

    Ajanga, S.I.

    2002-01-01

    Cob rots are a major cause of crop loss in areas such as western Kenya that experience prolonged rainfall during the period of crop maturation. Cob rot fungi cause spoilage of the grain and some of them produce mycotoxins which can pose a health risk to humans and animals consuming foods prepared from contaminate grain. survey conducted in western Kenya in 1998 showed that cob rot incidence exceeded 20%. In the following year when rainfall was greater around the harvest period, cob rot fungi affected 68% of cobs. in 1998 stalk borer larvae (mainly Busseola fusca) damaged 20% of the cobs and there was a strong correlation (R= 0.87) between cob rot incidence and borer damage. In 1999 almost half of the cobs sampled showed evidence of borer damage. The result indicate that the high cob rot incidence in this pert of Kenya is due to stalk bore damage, which predisposes the cobs to fungal infection, and that management of the borer would greatly decrease cob rot incidence

  5. Improved enzymatic saccharification of steam exploded cotton stalk using alkaline extraction and fermentation of cellulosic sugars into ethanol.

    Science.gov (United States)

    Keshav, Praveen K; Naseeruddin, Shaik; Rao, L Venkateswar

    2016-08-01

    Cotton stalk, a widely available and cheap agricultural residue lacking economic alternatives, was subjected to steam explosion in the range 170-200°C for 5min. Steam explosion at 200°C and 5min led to significant hemicellulose solubilization (71.90±0.10%). Alkaline extraction of steam exploded cotton stalk (SECOH) using 3% NaOH at room temperature for 6h led to 85.07±1.43% lignin removal with complete hemicellulose solubilization. Besides, this combined pretreatment allowed a high recovery of the cellulosic fraction from the biomass. Enzymatic saccharification was studied between steam exploded cotton stalk (SECS) and SECOH using different cellulase loadings. SECOH gave a maximum of 785.30±8.28mg/g reducing sugars with saccharification efficiency of 82.13±0.72%. Subsequently, fermentation of SECOH hydrolysate containing sugars (68.20±1.16g/L) with Saccharomyces cerevisiae produced 23.17±0.84g/L ethanol with 0.44g/g yield. Copyright © 2016 Elsevier Ltd. All rights reserved.

  6. Brittle stalk 2 encodes a putative glycosylphosphatidylinositol-anchored protein that affects mechanical strength of maize tissues by altering the composition and structure of secondary cell walls.

    Science.gov (United States)

    Ching, Ada; Dhugga, Kanwarpal S; Appenzeller, Laura; Meeley, Robert; Bourett, Timothy M; Howard, Richard J; Rafalski, Antoni

    2006-10-01

    A spontaneous maize mutant, brittle stalk-2 (bk2-ref), exhibits dramatically reduced tissue mechanical strength. Reduction in mechanical strength in the stalk tissue was highly correlated with a reduction in the amount of cellulose and an uneven deposition of secondary cell wall material in the subepidermal and perivascular sclerenchyma fibers. Cell wall accounted for two-thirds of the observed reduction in dry matter content per unit length of the mutant stalk in comparison to the wildtype stalk. Although the cell wall composition was significantly altered in the mutant in comparison to the wildtype stalks, no compensation by lignin and cell wall matrix for reduced cellulose amount was observed. We demonstrate that Bk2 encodes a Cobra-like protein that is homologous to the rice Bc1 protein. In the bk2-ref gene, a 1 kb transposon-like element is inserted in the beginning of the second exon, disrupting the open reading frame. The Bk2 gene was expressed in the stalk, husk, root, and leaf tissues, but not in the embryo, endosperm, pollen, silk, or other tissues with comparatively few or no secondary cell wall containing cells. The highest expression was in the isolated vascular bundles. In agreement with its role in secondary wall formation, the expression pattern of the Bk2 gene was very similar to that of the ZmCesA10, ZmCesA11, and ZmCesA12 genes, which are known to be involved in secondary wall formation. We have isolated an independent Mutator-tagged allele of bk2, referred to as bk2-Mu7, the phenotype of which is similar to that of the spontaneous mutant. Our results demonstrate that mutations in the Bk2 gene affect stalk strength in maize by interfering with the deposition of cellulose in the secondary cell wall in fiber cells.

  7. Biocompatible nanoemulsions based on hemp oil and less surfactants for oral delivery of baicalein with enhanced bioavailability

    Directory of Open Access Journals (Sweden)

    Yin J

    2017-04-01

    Full Text Available Juntao Yin,1,* Cuiyu Xiang,1,* Peiqing Wang,1 Yuyun Yin,2 Yantao Hou3 1Department of Pharmaceutics, Huaihe Hospital Affiliated to Henan University, Kaifeng, 2Department of Physiochemical Analysis, Henan Provincial Institute for Food and Drug Control, Zhengzhou, 3Department of Pharmaceutical Engineering, Henan Vocational College of Applied Technology, Kaifeng, People’s Republic of China *These authors contributed equally to this work Abstract: Baicalein (BCL possesses high pharmacological activities but low solubility and stability in the intestinal tract. This study aimed to probe the potential of nanoemulsions (NEs consisting of hemp oil and less surfactants in ameliorating the oral bioavailability of BCL. BCL-loaded NEs (BCL-NEs were prepared by high-pressure homogenization technique to reduce the amount of surfactants. BCL-NEs were characterized by particle size, entrapment efficiency (EE, in vitro drug release, and morphology. Bioavailability was studied in Sprague-Dawley rats following oral administration of BCL suspensions, BCL conventional emulsions, and BCL-NEs. The obtained NEs were ~90 nm in particle size with an EE of 99.31%. BCL-NEs significantly enhanced the oral bioavailability of BCL, up to 524.7% and 242.1% relative to the suspensions and conventional emulsions, respectively. BCL-NEs exhibited excellent intestinal permeability and transcellular transport ability. The cytotoxicity of BCL-NEs was documented to be low and acceptable for oral purpose. Our findings suggest that such novel NEs and preparative process provide a promising alternative to current formulation technologies and suitable for oral delivery of drugs with bioavailability issues. Keywords: baicalein, nanoemulsions, biocompatibility, high-pressure homogenization, hemp oil, bioavailability

  8. Effect of gamma irradiation on the structure of corn stalks and their subsequent bioconversion into protein-rich mycelial biomass of pleurotus sajor-caju

    Energy Technology Data Exchange (ETDEWEB)

    Awafo, V [Quebec Univ., Montreal, PQ (Canada)

    1994-12-31

    Lignocellulosic biomass like corn stalk is an abundant and renewable resource from which food, feed and chemicals may be derived. Enzymatic hydrolysis of native lignocellulosic material is prohibitively slow due to their compositional heterogeneity and structural complexity. In this work, ground corn stalks (20 mesh) were subjected to gamma irradiation (10-170 Mrads) as pretreatments to make them more susceptible for bioconversion into protein-rich mycelial biomass of Pleurotus sajor-caju NRRL 18757. The irradiation was carried out in air in a {sup 60}Co Underwater Calibrator (UC-15, Nordion International) at a dose rate of 2.5 Mrads/h as measured by Fricke dosimetry. No apparent structural differences were observed under the light microscope. However, the protein synthesis and the proportion of mycelial biomass increased with the increase in both the dose of irradiation and time of fermentation during the bioconversion of 1% corn stalk into mycelial biomass of Pleurotus sajor-caju. Gamma irradiation at the dose of 50 Mrads or lower did not produce any appreciable increase in the amount of protein synthesised. At 170 Mrads, the final product contained 28% protein representing a 2-fold increase from non-irradiated corn stalk and an efficiency of 36% conversion of total utilizable polysaccharides of corn stalks into mycelial biomass. The lag phase during mycelial biomass production was much more prolonged at very high doses indicating possible production of some toxic substances during irradiation. (author). 2 tabs., 6 figs.

  9. Identification of fasciclin-like arabinogalactan proteins in textile hemp (Cannabis sativa L.): in silico analyses and gene expression patterns in different tissues.

    Science.gov (United States)

    Guerriero, Gea; Mangeot-Peter, Lauralie; Legay, Sylvain; Behr, Marc; Lutts, Stanley; Siddiqui, Khawar Sohail; Hausman, Jean-Francois

    2017-09-20

    The fasciclin-like arabinogalactan proteins (FLAs) belong to the arabinogalactan protein (AGP) superfamily and are known to play different physiological roles in plants. This class of proteins was shown to participate in plant growth, development, defense against abiotic stresses and, notably, cell wall biosynthesis. Although some studies are available on the characterization of FLA genes from different species, both woody and herbaceous, no detailed information is available on the FLA family of textile hemp (Cannabis sativa L.), an economically important fibre crop. By searching the Cannabis genome and EST databases, 23 CsaFLAs have been here identified which are divided into four phylogenetic groups. A real-time qPCR analysis performed on stem tissues (isolated bast fibres and shivs sampled at three heights), hypocotyls (6-9-12-15-17-20 days-old), whole seedlings, roots, leaves and female/male flowers of the monoecious fibre variety Santhica 27, indicates that the identified FLA genes are differentially expressed. Interestingly, some hemp FLAs are expressed during early phases of fibre growth (elongation), while others are more expressed in the middle and base of the stem and thus potentially involved in secondary cell wall formation (fibre thickening). The bioinformatic analysis of the promoter regions shows that the FLAs upregulated in the younger regions of the stem share a conserved motif related to flowering control and regulation of photoperiod perception. The promoters of the FLA genes expressed at higher levels in the older stem regions, instead, share a motif putatively recognized by MYB3, a transcriptional repressor belonging to the MYB family subgroup S4. These results point to the existence of a transcriptional network fine-tuning the expression of FLA genes in the older and younger regions of the stem, as well as in the bast fibres/shivs of textile hemp. In summary, our study paves the way for future analyses on the biological functions of FLAs in

  10. A rare cause of hyperprolactinemia: persistent trigeminal artery with stalk-section effect

    International Nuclear Information System (INIS)

    Ekinci, G.; Baltacioglu, F.; Cimsit, C.; Akpinar, I.; Erzen, C.; Kilic, T.; Pamir, N.

    2001-01-01

    The primitive trigeminal, otic, hypoglossal, and proatlantal intersegmental arteries are fetal anastomoses between the carotid and vertebrobasilar systems. Persistent trigeminal artery (PTA) is the most frequent embryonic communication between the vertebrobasilar and carotid systems in adults. We report a case of PTA compressing the left side of the pituitary gland and stalk, in a patient with elevated blood prolactin level. (orig.)

  11. Essai de caractérisation des phénomènes de stalking dans un contexte juridique et politique : radiogoniométrie et filature On characterization of stalking phenomena in a juridical and political context: radiogoniometry and tracking

    Directory of Open Access Journals (Sweden)

    Desurmont N.

    2010-12-01

    Full Text Available De nos jours il est devenu impossible d’étudier les filatures comme on les pratiquait avant la naissance de la triangulation et de la radiogoniométrie, les observations satellitaires, les communications radios, etc. En effet l’usage de la radiogoniométrie et de d’autres techniques par les services des renseignements généraux et les forces de l’ordre biaisent aujourd’hui fortement l’analyse des filatures de ces organes en ayant recours qu’à l’analyse topologique et la géocriminologie. Le présent texte est une version abrégée d’une étude plus complète sur la représentation de l’espace criminel et sur la topographie policière par l’analyse des techniques de filature et de traçabilité. Il cherche à élargir le champ de l’activité de la police scientifique de telle manière à mieux diagnostiquer une série d’infractions impliquant des techniques de poursuites. Bien que beaucoup d’infractions nécessitent, pour être commises, la pratique de techniques de poursuite, c’est essentiellement en se basant sur des infractions telle la recherche et la poursuite, le stalking et le harcèlement moral en réseau (ou harcèlement organisationnel que nous avons pu énoncer les principes de la victimisation organisationnelle.Nowadays it has become impossible to study the technics of stalking as they were practiced before the birth of mobile phone localisation, satellite observations, communications radios, etc.. Indeed the use of mobile phone localization and other techniques by intelligence services and law enforcement officials today strongly distort the analysis of stalking of these organs by using only the topological analysis and geocriminology. This text is a reduced version of a more comprehensive study of the following technics of spatial representation and as well the analysis of police surveillance techniques and traceability. It seeks to broaden the scope of activity of forensic science in such a way as

  12. Needle knife-assisted endoscopic polypectomy for a large inflammatory fibroid colon polyp by making its stalk into an omega shape using an endoloop.

    Science.gov (United States)

    Kim, Byung Chang; Cheon, Jae Hee; Lee, Sang Kil; Kim, Tae Il; Kim, Hoguen; Kim, Won Ho

    2008-08-30

    Colonic inflammatory fibroid polyp (IFP) is an uncommon benign polypoid lesion, which is composed of fibroblasts, numerous small vessels and edematous connective tissue with marked eosinophilic inflammatory cell infiltration. This condition is frequently detected in the stomach and small intestine, but uncommon in the colon. Although IFP is a benign lesion, surgical resections are performed in most colonic cases because the polyps are usually too large to resect endoscopically. Only three patients underwent endoscopic polypectomy in our literature reviews. Here, we present a case of IFP in the descending colon successful endoscopically resected using a novel technique of trapping its stalk with an endoloop, forming the stalk into an omega shape, and then dissecting the stalk with a needle knife.

  13. Delayed diagnosis of pituitary stalk interruption syndrome with severe recurrent hyponatremia caused by adrenal insufficiency

    Directory of Open Access Journals (Sweden)

    Kyung Mi Jang

    2017-09-01

    Full Text Available Pituitary stalk interruption syndrome (PSIS involves the occurrence of a thin or absent pituitary stalk, hypoplasia of the adenohypophysis, and ectopic neurohypophysis. Diagnosis is confirmed using magnetic resonance imaging. Patients with PSIS have a variable degree of pituitary hormone deficiency and a wide spectrum of clinical manifestations. The clinical course of the disease in our patient is similar to that of a syndrome of inappropriate antidiuretic hormone secretion. This is thought to be caused by failure in the suppression of vasopressin secretion due to hypocortisolism. To the best of our knowledge, there is no case report of a patient with PSIS presenting with hyponatremia as the first symptom in Korean children. Herein, we report a patient with PSIS presenting severe recurrent hyponatremia as the first symptom, during adolescence and explain the pathophysiology of hyponatremia with secondary adrenal insufficiency.

  14. Pituitary stalk interruption syndrome in Chinese people: clinical characteristic analysis of 55 cases.

    Directory of Open Access Journals (Sweden)

    Qinghua Guo

    Full Text Available OBJECTIVE: Pituitary stalk interruption syndrome (PSIS is characterized by the absence of pituitary stalk, pituitary hypoplasia, and ectopic posterior pituitary. Due to the rarity of PSIS, clinical data are limited, especially in Chinese people. Herein, we analyzed the clinical characteristics of patients diagnosed with PSIS from our center over 10 years. PATIENTS AND METHODS: We retrospectively analyzed the clinical manifestations and laboratory and MRI findings in 55 patients with PSIS. RESULTS: Of the 55 patients with PSIS, 48 (87.3% were male. The average age was 19.7±6.7 years and there was no familial case. A history of breech delivery was documented in 40 of 45 patients (88.9% and 19 of 55 patients (34.5% had a history of dystocia. Short stature was found in 47 of 55 patients (85.5% and bone age delayed 7.26±5.37 years. Secondary sex characteristics were poor or undeveloped in most patients. The prevalence of deficiencies in growth hormone, gonadotropins, corticotropin, and thyrotropin were 100%, 95.8%, 81.8%, 76.3%, respectively. Hyperprolactinemia was found in 36.4% of patients. Three or more pituitary hormone deficiencies were found in 92.7% of the patients. All patients had normal posterior pituitary function and absent pituitary stalk on imaging. The average height of anterior pituitary was 28 mm, documented anterior pituitary hypoplasia. Midline abnormalities were presented in 9.1% of patients. CONCLUSIONS: The clinical features of our Chinese PSIS patients seem to be different from other reported patients in regarding to the higher degree of hypopituitarism and lower prevalence of midline defects. In addition, our patients were older at the time of case detection and the bone age was markedly delayed. We also had no cases of familial PSIS.

  15. Influence of steaming explosion time on the physic-chemical properties of cellulose from Lespedeza stalks (Lespedeza crytobotrya).

    Science.gov (United States)

    Wang, Kun; Jiang, Jian-Xin; Xu, Feng; Sun, Run-Cang

    2009-11-01

    The synergistic effect of steam explosion pretreatment and sodium hydroxide post-treatment of Lespedeza stalks (Lespedeza crytobotrya) has been investigated in this study. In this case, Lespedeza stalks were firstly exploded at a fixed steam pressure (22.5 kg/m(2)) for 2-10 min. Then the steam-exploded Lespedeza stalks was extracted with 1 M NaOH at 50 degrees C for 3 h with a shrub to water ratio of 1:20 (g/ml), which yielded 57.3%, 53.1%, 55.4%, 52.8%, 53.2%, and 56.4% (% dry weight) cellulose rich fractions, comparing to 68.0% from non-steam-exploded material. The content of glucose in cellulose rich residues increased with increment of the steaming time and reached to 94.10% at the most severity. The similar increasing trend occurred during the dissolution of hemicelluloses. It is evident that at shorter steam explosion time, autohydrolysis mainly occurred on the hemicelluloses and the amorphous area of cellulose. The crystalline region of cellulose was depolymerized under a prolonged incubation time. The characteristics of the cellulose rich fractions in terms of FT-IR and CP/MAS (13)C NMR spectroscopy and thermal analysis were discussed, and the surface structure was also investigated by SEM.

  16. The C-terminal helix of ribosomal P stalk recognizes a hydrophobic groove of elongation factor 2 in a novel fashion.

    Science.gov (United States)

    Tanzawa, Takehito; Kato, Koji; Girodat, Dylan; Ose, Toyoyuki; Kumakura, Yuki; Wieden, Hans-Joachim; Uchiumi, Toshio; Tanaka, Isao; Yao, Min

    2018-04-06

    Archaea and eukaryotes have ribosomal P stalks composed of anchor protein P0 and aP1 homodimers (archaea) or P1•P2 heterodimers (eukaryotes). These P stalks recruit translational GTPases to the GTPase-associated center in ribosomes to provide energy during translation. The C-terminus of the P stalk is known to selectively recognize GTPases. Here we investigated the interaction between the P stalk and elongation factor 2 by determining the structures of Pyrococcus horikoshii EF-2 (PhoEF-2) in the Apo-form, GDP-form, GMPPCP-form (GTP-form), and GMPPCP-form bound with 11 C-terminal residues of P1 (P1C11). Helical structured P1C11 binds to a hydrophobic groove between domain G and subdomain G' of PhoEF-2, where is completely different from that of aEF-1α in terms of both position and sequence, implying that such interaction characteristic may be requested by how GTPases perform their functions on the ribosome. Combining PhoEF-2 P1-binding assays with a structural comparison of current PhoEF-2 structures and molecular dynamics model of a P1C11-bound GDP form, the conformational changes of the P1C11-binding groove in each form suggest that in response to the translation process, the groove has three states: closed, open, and release for recruiting and releasing GTPases.

  17. STUDY REGARDING THE INFLUENCE OF THE BIOSCOURING TREATMENT IN ULTRASOUND ON 60 % COTTON + 40 % HEMP MATERIALS PART II. STUDY REGARDING THE INFLUENCE OF BIOSCOURI NG TREATMENT FOLLOWED BY A WHITENING TREATMENT USING VARIOUS METHODS

    Directory of Open Access Journals (Sweden)

    DOCHIA Mihaela

    2014-05-01

    Full Text Available This study shows a comparative characterization of whitening treatment using various processes for 60 % cotton +40 % hemp materials scoured by Bioscouring treatment in ultrasound described in our previous work. The results of the extraction of noncellulosic impurities using the Bioscouring treatment was ex pressed as weight loss, hydrophilicity. Some of these bio-scoured samples were whitened using various procedures: Classical procedure with hydrogen peroxide (30%, with catalyst and with laccase enzyme. By whitening procedure, the double bonds from chromophore groups of natural pigments from cotton and hemp are destroyed by oxidation reactions, the Π electrons being those responsible for the yellow color of the fabrics. In order to characterize the quality of the enzymatic pretreatment compared to the classical one, the values of the degree of white were studied after different type of bleaching (hydrogen peroxide, catalyst and laccase for the samples treated with the same concentration of enzyme SERA ZYME C-PE (ROGLYR ECO 183 - Pectate Lyase. For comparing the degradation occurred during the enzymatic preatreatment of cellulosic fabrics, before and after bleaching with enzymes, catalyst and classical method, measurements of the tensile strength and elongation at break for the treated 60 % cotton +40 % hemp material, were performed.

  18. Ribosomal Stalk Protein Silencing Partially Corrects the ΔF508-CFTR Functional Expression Defect.

    Directory of Open Access Journals (Sweden)

    Guido Veit

    2016-05-01

    Full Text Available The most common cystic fibrosis (CF causing mutation, deletion of phenylalanine 508 (ΔF508 or Phe508del, results in functional expression defect of the CF transmembrane conductance regulator (CFTR at the apical plasma membrane (PM of secretory epithelia, which is attributed to the degradation of the misfolded channel at the endoplasmic reticulum (ER. Deletion of phenylalanine 670 (ΔF670 in the yeast oligomycin resistance 1 gene (YOR1, an ABC transporter of Saccharomyces cerevisiae phenocopies the ΔF508-CFTR folding and trafficking defects. Genome-wide phenotypic (phenomic analysis of the Yor1-ΔF670 biogenesis identified several modifier genes of mRNA processing and translation, which conferred oligomycin resistance to yeast. Silencing of orthologues of these candidate genes enhanced the ΔF508-CFTR functional expression at the apical PM in human CF bronchial epithelia. Although knockdown of RPL12, a component of the ribosomal stalk, attenuated the translational elongation rate, it increased the folding efficiency as well as the conformational stability of the ΔF508-CFTR, manifesting in 3-fold augmented PM density and function of the mutant. Combination of RPL12 knockdown with the corrector drug, VX-809 (lumacaftor restored the mutant function to ~50% of the wild-type channel in primary CFTRΔF508/ΔF508 human bronchial epithelia. These results and the observation that silencing of other ribosomal stalk proteins partially rescue the loss-of-function phenotype of ΔF508-CFTR suggest that the ribosomal stalk modulates the folding efficiency of the mutant and is a potential therapeutic target for correction of the ΔF508-CFTR folding defect.

  19. Digenic Inheritance of PROKR2 and WDR11 Mutations in Pituitary Stalk Interruption Syndrome.

    Science.gov (United States)

    McCormack, Shana E; Li, Dong; Kim, Yeon Joo; Lee, Ji Young; Kim, Soo-Hyun; Rapaport, Robert; Levine, Michael A

    2017-07-01

    Pituitary stalk interruption syndrome (PSIS, ORPHA95496) is a congenital defect of the pituitary gland characterized by the triad of a very thin/interrupted pituitary stalk, an ectopic (or absent) posterior pituitary gland, and hypoplasia or aplasia of the anterior pituitary gland. Complex genetic patterns of inheritance of this disorder are increasingly recognized. The objective of this study was to identify a genetic cause of PSIS in an affected child. Whole exome sequencing (WES) was performed by using standard techniques, with prioritized genetic variants confirmed via Sanger sequencing. To investigate the effects of one candidate variant on mutant WDR11 function, Western blotting and coimmunofluorescence were used to assess binding capacity, and leptomycin B exposure along with immunofluorescence was used to assess nuclear localization. We describe a child who presented in infancy with combined pituitary hormone deficiencies and whose brain imaging demonstrated a small anterior pituitary, ectopic posterior pituitary, and a thin, interrupted stalk. WES demonstrated heterozygous missense mutations in two genes required for pituitary development, a known loss-of-function mutation in PROKR2 (c.253C>T;p.R85C) inherited from an unaffected mother, and a WDR11 (c.1306A>G;p.I436V) mutation inherited from an unaffected father. Mutant WDR11 loses its capacity to bind to its functional partner, EMX1, and to localize to the nucleus. WES in a child with PSIS and his unaffected family implicates a digenic mechanism of inheritance. In cases of hypopituitarism in which there is incomplete segregation of a monogenic genotype with the phenotype, the possibility that a second genetic locus is involved should be considered. Copyright © 2017 Endocrine Society

  20. Pituitary stalk transection syndrome: Comparison of clinico-radiological features in adults and children with review of literature

    International Nuclear Information System (INIS)

    Kulkarni, Chinmay; Moorthy, Srikanth; Pullara, Sreekumar K; Rajeshkannan, R; Unnikrishnan, Ambika G

    2012-01-01

    Hypo-pituitarism results from impaired production of one or more of anterior pituitary trophic hormones. A rare cause of hypo-pituitarism is pituitary stalk transection syndrome. The MRI features of this condition in children and its association with hormonal deficiencies have been reported earlier. Reports on adults with this disorder are scarce, with only one small case series published in the recent literature. We studied the hormonal deficiency pattern and MRI findings of 12 patients with pituitary stalk transection syndrome who presented to our department between 2004 and 2011. Six patients were children and six were adults (≥18 years). This article compares the adult clinico-radiological phenotype of pituitary transection syndrome with the pediatric group of patients with same condition

  1. Post-harvest treatments in smooth-stalked meadow grass (Poa pratensis L.) - effect on carbohydrates and tiller development

    DEFF Research Database (Denmark)

    Boelt, Birte

    2007-01-01

    Temperate grass species require a period of short days/low temperature to respond to flower induction stimuli. The same environmental conditions stimulate the increase in carbohydrate concentration in aboveground biomass and the accumulation of reserve carbohydrates in the basal plant parts....... The present investigation was initiated to investigate the effect of post-harvest treatments on dry matter production in autumn, carbohydrate content, the number of reproductive tillers and seed yield in a turf-type cultivar ‘Conni' of smooth-stalked meadow grass. The results show that post-harvest treatments...... harvest and all residues removed. The results from plant samples in autumn indicate that decreasing aboveground biomass production leads to a higher carbohydrate concentration which may stimulate the reproductive development in smooth-stalked meadow grass....

  2. H2O2 can Increase Lignin Disintegration and Decrease Cellulose Decomposition in the Process of Solid-State Fermentation (SSF) by Aspergillus oryzae Using Corn Stalk as Raw Materials

    OpenAIRE

    Zhicai Zhang; Jun Jia; Ming Li; Qiaoxia Pang

    2014-01-01

    H2O2 is both bactericidal and the main oxidant responsible for lignin degradation reaction catalyzed by manganese peroxidase (MnP) and lignin peroxidase (LiP). Thus, H2O2 treatment of corn stalk and the implementation of solid-substrate fermentation (SSF) is possible to increase the removal rate of lignin from stalk in the process of SSF and after SSF, while avoiding the need to sterilize the raw materials. To demonstrate this approach, SSF was initially carried out using corn stalk pretreate...

  3. Dynamic mechanical analysis and crystalline analysis of hemp fiber reinforced cellulose filled epoxy composite

    Energy Technology Data Exchange (ETDEWEB)

    Palanivel, Anand; Duruvasalu, Rajesh; Iyyanar, Saranraj; Velumayil, Ramesh, E-mail: p.anand@ymail.com [Mechanical Engineering, Vel Tech Dr RR. & Dr. SR University, Avadi, Chennai, Tamilnadu (India); Veerabathiran, Anbumalar [Mechanical Engineering, Velammal College of Engineering & Technology, Madurai, TN (India)

    2017-07-01

    The Dynamic mechanical behavior of chemically treated and untreated hemp fiber reinforced composites was investigated. The morphology of the composites was studied to understand the interaction between the filler and polymer. A series of dynamic mechanical tests were performed by varying the fiber loading and test frequencies over a range of testing temperatures. It was found that the storage modulus (E') recorded above the glass transition temperature (Tg) decrease with increasing temperature. The loss modulus (E”) and damping peaks (Tan δ) values were found to be reduced with increasing matrix loading and temperature. Morphological changes and crystallinity of Composites were investigated using scanning electron microscope (SEM) and XRD techniques. The composites with Alkali and Benzoyl treated fibers has attributed enhanced DMA Results. In case of XRD studies, the composites with treated fibers with higher filler content show enhanced crystallinity. (author)

  4. Dynamic mechanical analysis and crystalline analysis of hemp fiber reinforced cellulose filled epoxy composite

    Directory of Open Access Journals (Sweden)

    Anand Palanivel

    Full Text Available Abstract The Dynamic mechanical behavior of chemically treated and untreated hemp fiber reinforced composites was investigated. The morphology of the composites was studied to understand the interaction between the filler and polymer. A series of dynamic mechanical tests were performed by varying the fiber loading and test frequencies over a range of testing temperatures. It was found that the storage modulus (E’ recorded above the glass transition temperature (Tg decrease with increasing temperature. The loss modulus (E” and damping peaks (Tan δ values were found to be reduced with increasing matrix loading and temperature. Morphological changes and crystallinity of Composites were investigated using scanning electron microscope (SEM and XRD techniques. The composites with Alkali and Benzoyl treated fibers has attributed enhanced DMA Results. In case of XRD studies, the composites with treated fibers with higher filler content show enhanced crystallinity.

  5. H2O2 can Increase Lignin Disintegration and Decrease Cellulose Decomposition in the Process of Solid-State Fermentation (SSF by Aspergillus oryzae Using Corn Stalk as Raw Materials

    Directory of Open Access Journals (Sweden)

    Zhicai Zhang

    2014-04-01

    Full Text Available H2O2 is both bactericidal and the main oxidant responsible for lignin degradation reaction catalyzed by manganese peroxidase (MnP and lignin peroxidase (LiP. Thus, H2O2 treatment of corn stalk and the implementation of solid-substrate fermentation (SSF is possible to increase the removal rate of lignin from stalk in the process of SSF and after SSF, while avoiding the need to sterilize the raw materials. To demonstrate this approach, SSF was initially carried out using corn stalk pretreated with different concentrations of H2O2 as a substrate. A. oryzae was found to grow well in the 3% H2O2-pretreated corn stalk. H2O2-pretreated corn stalk showed increased MnP and LiP synthesis and disintegration of lignin, but inhibited cellulase synthesis and cellulose degradation. Production of the SSF (200 g on the 10th day was hydrolyzed in the presence of additional 600 mL different concentration of H2O2 aqueous solution. The total removal of lignin (73.15% of hydrolysis for 10 h at 3% H2O2 solution was highest and far higher than that at the 12th day, as achieved by conventional SSF. Applying this strategy in practice may shorten the time of lignin degradation, increase the removal of lignin, and decrease the loss of cellulose. Thus, this study has provided a foundation for further study saccharification of corn stalk.

  6. Wet Oxidation Pretreatment of Tobacco Stalks and Orange Waste for Bioethanol Production. Preliminary results

    DEFF Research Database (Denmark)

    Martin, Carlos; Fernandez, Teresa; Garcia, Ariel

    2009-01-01

    Wet oxidation (WO) was used as a pretreatment method prior to enzymatic hydrolysis of tobacco stalks and orange waste. The pretreatment, performed at 195 degrees C and an oxygen pressure of 1.2 MPa, for 15 min, in the presence of Na2CO3, increased the cellulose content of the materials and gave c...

  7. Selected Abiotic and Biotic Environmental Stress Factors Affecting Two Economically Important Sugarcane Stalk Boring Pests in the United States

    Directory of Open Access Journals (Sweden)

    Allan T. Showler

    2016-02-01

    Full Text Available Sugarcane, Saccharum spp., in the United States is attacked by a number of different arthropod pests. The most serious among those pests are two stalk boring moths in the Family Crambidae: the sugarcane borer, Diatraea saccharalis (F., and the Mexican rice borer, Eoreuma loftini (Dyar. The two species are affected by abiotic and biotic environmental stress factors. Water deficit and excessive soil nitrogen alter physical and physiochemical aspects of the sugarcane plant that make the crop increasingly vulnerable to E. loftini. Weed growth can be competitive with sugarcane but it also supports enhanced abundances and diversity of natural enemies that can suppress infestations of D. saccharalis. In an instance where the stalk borer is considered a stress factor, proximity of vulnerable crops to sugarcane can influence levels of E. loftini infestation of sugarcane. The adverse effects of each stress factor, in terms of stalk borer attack, can be reduced by adopting appropriate cultural practices, such as adequate irrigation, judicious use of nitrogen fertilizer, using noncompetitive weed growth, and not planting vulnerable crops near sugarcane fields. Understanding the relationships between stress factors and crop pests can provide valuable insights for plant breeders and tools for incorporation into integrated pest management strategies.

  8. Central diabetes insipidus as a very late relapse limited to the pituitary stalk in Langerhans cell histiocytosis.

    Science.gov (United States)

    Nakagawa, Shunsuke; Shinkoda, Yuichi; Hazeki, Daisuke; Imamura, Mari; Okamoto, Yasuhiro; Kawakami, Kiyoshi; Kawano, Yoshifumi

    2016-07-01

    Central diabetes insipidus (CDI) and relapse are frequently seen in multifocal Langerhans cell histiocytosis (LCH). We present two females with multifocal LCH who developed CDI 9 and 5 years after the initial diagnosis, respectively, as a relapse limited to the pituitary stalk. Combination chemotherapy with cytarabine reduced the mass in the pituitary stalk. Although CDI did not improve, there has been no anterior pituitary hormone deficiency (APHD), neurodegenerative disease in the central nervous system (ND-CNS) or additional relapse for 2 years after therapy. It was difficult to predict the development of CDI in these cases. CDI might develop very late in patients with multifocal LCH, and therefore strict follow-up is necessary, especially with regard to symptoms of CDI such as polydipsia and polyuria. For new-onset CDI with LCH, chemotherapy with cytarabine might be useful for preventing APHD and ND-CNS.

  9. Optimization of pulsed electric field pre-treatments to enhance health-promoting glucosinolates in broccoli flowers and stalk.

    Science.gov (United States)

    Aguiló-Aguayo, Ingrid; Suarez, Manuel; Plaza, Lucia; Hossain, Mohammad B; Brunton, Nigel; Lyng, James G; Rai, Dilip K

    2015-07-01

    The effect of pulsed electric field (PEF) treatment variables (electric field strength and treatment time) on the glucosinolate content of broccoli flowers and stalks was evaluated. Samples were subjected to electric field strengths from 1 to 4 kV cm(-1) and treatment times from 50 to 1000 µs at 5 Hz. Data fitted significantly (P broccoli flowers (ranging from 187.1 to 212.5%) and stalks (ranging from 110.6 to 203.0%) respectively. The predicted values from the developed quadratic polynomial equation were in close agreement with the actual experimental values, with low average mean deviations (E%) ranging from 0.59 to 8.80%. The use of PEF processing at moderate conditions could be a suitable method to stimulate production of broccoli with high health-promoting glucosinolate content. © 2014 Society of Chemical Industry.

  10. LOFT reactor vessel 290/sup 0/ downcomer stalk instrument penetration flange stress analysis

    Energy Technology Data Exchange (ETDEWEB)

    Finicle, D.P.

    1978-06-06

    The LOFT Reactor Vessel 290/sup 0/ Downcomer Stalk Instrument Penetration Flange Stress Analysis has been completed using normal operational and blowdown loading. A linear elastic analysis was completed using simplified hand analysis techniques. The analysis was in accordance with the 1977 ASME Boiler and Pressure Vessel Code, Section III, for a Class 1 component. Loading included internal pressure, bolt preload, and thermal gradients due to normal operating and blowdown.

  11. Transection of the pituitary stalk: evaluation of two cases by computerized tomography and magnetic resonance

    International Nuclear Information System (INIS)

    Amaral, L.L.F. do; Mendonca, R.A.; Natal, M.R.C.

    1992-01-01

    The authors present two cases of pituitary dwarfism where the study by high resolution computed tomography and by magnetic resonance imaging show transection of the pituitary stalk as the cause of the endocrine disturb. The importance of these methods on the investigation of disturbs of the hypothalamus-hypophyseal axis is stressed. (author)

  12. Changes in Soil C/N Ratio and Response of Growth of Hemp (Cannabis sativa L. to Different Levels of Animal Manure and Chemical Fertilizers

    Directory of Open Access Journals (Sweden)

    S Laleh

    2018-05-01

    Full Text Available Introduction Hemp is used in the food, drug, and natural fibers. Assessment of various systems of plant nutrition is one of the ways to improve field management and production of medicinal plants. Nitrogen is considered a necessary element in plant nutrition. Nitrogen uptake as ammonium compounds form, serves as starting material for amino acid biosynthesis and additional N-containing compound such as pyrimidine, purine bases, chlorophyll, proteins, nucleic acid, vitamins and other organic compounds, therefore, the higher plants require larger amount of nitrogen. Phosphorus is the second most important nutrient in plants. Studies show that application of animal manure provides different nutrients for plants. Application of animal manure in soil at the optimal level for plant growth provides a opportunities for soil fertility, conservation, sustainability, and protection against degradation but they need time to release their nutrient. Various studies showed that the combined usage the animal manure and chemical fertilizers (like N and P has positive effects on soil, growth and yield of plant with the aim of protecting the environment. Organic and inorganic fertilizers are effective on soil C/N ratio. Soil C/N ratio is important factor for plant and soil. It is important to study the different stages of plant growth responses to organic and chemical fertilizers for plants production. Therefore, the present study was undertaken to evaluate the effect of organic amendments enriched with chemical fertilizers of nitrogen and phosphorus and studying changes of soil C/N ratio in vegetative and reproductive stages of hemp. Materials and Methods To study the effect of different levels of animal manure and chemical fertilizers, a split factorial experiment, based on complete randomized blocks design with three replications was conducted at the Research Farm of Faculty of agriculture, University of Birjand, during the growing season 2013-2014. Experimental

  13. Frakcja lipidowa i białkowa nasion konopi siewnych (C. sativa L. oraz jej korzystny wpływ na zdrowie człowieka = Lipid and protein fraction of hemp seed (C. sativa L. and its beneficial influence on human health

    Directory of Open Access Journals (Sweden)

    Grzegorz Dąbrowski

    2016-09-01

      Abstrakt Wprowadzenie i cel pracy: Konopie siewne wykorzystywane są od tysięcy lat do produkcji włókien oraz oleju z nasion. W ostatnim czasie nasiona tej rośliny wykorzystuje się także do produkcji izolatów i hydrolizatów białek. Celem niniejszej pracy jest opisanie składu frakcji tłuszczowej i białkowej nasion konopi siewnych oraz potencjału zdrowotnego oleju oraz izolatów i hydrolizatów białkowych pochodzących z tego surowca. Skrócony opis stanu wiedzy: Nasiona konopi są bogatym źródłem oleju oraz białka. Skład oleju jest korzystny z żywieniowego punktu widzenia z uwagi na duży udział niezbędnych nienasyconych kwasów tłuszczowych (NNKT oraz korzystne proporcje kwasów n-6/n-3. Olej konopny zawiera także duże ilości związków bioaktywnych, takich jak fitosterole, karotenoidy, polifenole i tokoferole. Białko konopi cechuje się dobrym składem aminokwasów oraz jest źródłem bioaktywnych peptydów o działaniu antyoksydacyjnym. Podsumowanie: Ze względu na zawartość oleju o korzystnym składzie kwasów tłuszczowych i wartościowego białka, nasiona konopi powinny być coraz częściej wprowadzane do codziennej diety. Słowa kluczowe: konopie siewne, NNKT, bioaktywne peptydy, tokoferole, fitosterole, polifenole, karotenoidy   Abstract Introduction and purpose: Hemp are used for thousands of years to obtain the fiber and seed oil. Recently, the hemp seeds are also used for the production of protein hydrolysates and isolates. The aim of this study is to describe the composition of the fat and protein fractions. In addition health benefits of the consumption of the oil  and protein hydrolysates and isolates will be described. Brief description of the state of the knoweledge: Hemp seeds are a rich source of oil and protein. The oil composition is beneficial from a nutritional point of view due to the high content of essential fatty acids (EFAs in the optimal ratio of n-6 / n-3. Hemp oil also contains large amounts of a

  14. Resultados experimentais com a cultura da Crotalaria juncea L. L., como planta produtora de celulose para papel Results from field trials with Crotalaria juncea L. as fiber plant for paper pulp

    Directory of Open Access Journals (Sweden)

    Júlio César Medina

    1961-01-01

    Full Text Available São apresentados e discutidos os resultados de vários experimentos de campo realizados na Estação Experimental de Tatuí, do Instituto Agronômico, com a Crotalaria juncea L. como planta produtora de celulose para papel. Êsses resultados permitem fazer recomendações úteis sôbre o melhoramento técnico da cultura e da produção, no concernente às questões de variedades, espaçamento, densidade de semeação, época de semeação e época de colheita dos caules.This paper reports the results obtained in sunn hemp (Crotalaria juncea L. field trials carried out at the Tatui Experiment Station, São Paulo State. The trials were designed to study the effect of varieties, spacing x rate of seeding, time of sowing and time of harvesting on sunn hemp fiber production as a raw material for paper pulp. From the results achieved in these trials, the following recommendations can be made for growing sunn hemp as a fiber plant for paper pulp in the State of São Paulo. VARIETY: to use the common variety that is normally sowed for green manuring. TIME OF SOWING: to sow the seeds during october. RATE OF SEED SOWING AND SPACING: to sow the seeds at the rate of 100 lbs/ acre in rows spaced 8 inches apart. TIME OF HARVESTING: to harvest the stalks for mechanical fiber extraction when the seed pods are in the mature stage.

  15. Dominance of 'Gallionella capsiferriformans' and heavy metal association with Gallionella-like stalks in metal-rich pH 6 mine water discharge

    Science.gov (United States)

    Fabisch, Maria; Freyer, Gina; Johnson, Carol A.; Buchel, Georg; Akob, Denise M.; Neu, Thomas R.; Kusel, Kirsten

    2016-01-01

    Heavy metal-contaminated, pH 6 mine water discharge created new streams and iron-rich terraces at a creek bank in a former uranium-mining area near Ronneburg, Germany. The transition from microoxic groundwater with ~5 mm Fe(II) to oxic surface water may provide a suitable habitat for microaerobic iron-oxidizing bacteria (FeOB). In this study, we investigated the potential contribution of these FeOB to iron oxidation and metal retention in this high-metal environment. We (i) identified and quantified FeOB in water and sediment at the outflow, terraces, and creek, (ii) studied the composition of biogenic iron oxides (Gallionella-like twisted stalks) with scanning and transmission electron microscopy (SEM, TEM) as well as confocal laser scanning microscopy (CLSM), and (iii) examined the metal distribution in sediments. Using quantitative PCR, a very high abundance of FeOB was demonstrated at all sites over a 6-month study period. Gallionella spp. clearly dominated the communities, accounting for up to 88% ofBacteria, with a minor contribution of other FeOB such as Sideroxydans spp. and ‘Ferrovum myxofaciens’. Classical 16S rRNA gene cloning showed that 96% of the Gallionella-related sequences had ≥97% identity to the putatively metal-tolerant ‘Gallionella capsiferriformans ES-2’, in addition to known stalk formers such as Gallionella ferruginea and Gallionellaceae strain R-1. Twisted stalks from glass slides incubated in water and sediment were composed of the Fe(III) oxyhydroxide ferrihydrite, as well as polysaccharides. SEM and scanning TEM-energy-dispersive X-ray spectroscopy revealed that stalk material contained Cu and Sn, demonstrating the association of heavy metals with biogenic iron oxides and the potential for metal retention by these stalks. Sequential extraction of sediments suggested that Cu (52–61% of total sediment Cu) and other heavy metals were primarily bound to the iron oxide fractions. These results show the importance of

  16. Molecular Investigation of the Stem Snap Point in Textile Hemp

    Directory of Open Access Journals (Sweden)

    Marc Behr

    2017-12-01

    Full Text Available Fibre crops are important natural resources, as they sustainably provide bast fibres, an economically-valuable raw material used in the textile and biocomposite sectors. Among fibre crops, textile hemp (Cannabis sativa L. is appreciated for its long and strong gelatinous bast fibres. The stem of fibre crops is a useful system for cell wall-oriented studies, because it shows a strong tissue polarity with a lignified inner core and a cellulosic hypolignified cortex, as well as a basipetal lignification gradient. Along the stem axis of fibre crops, a specific region, denoted snap point, marks the transition from elongation (above it to fibre thickening (below it. After empirically determining the snap point by tilting the plant, we divided the stem segment containing it into three non-overlapping consecutive regions measuring 1 cm each, and carried out targeted RT-qPCR on cell wall-related genes separately, in outer and inner tissues. Different gene clusters can be observed, two of which are the major gene groups, i.e., one group with members expressed at higher levels in the inner tissues, and one group whose genes are more expressed in the cortex. The present results provide a molecular validation that the snap point is characterised by a gradient of events associated with the shift from fibre elongation to thickening.

  17. A stalk of grain and light

    Directory of Open Access Journals (Sweden)

    Erín Moure

    2010-11-01

    Full Text Available "Stalk of Grain and Light" is an excerpt from O Resplandor (Toronto: Anansi, forthcoming 2010, a book of poetry that explodes notions of authorship and translation. In it, the heteronymic character Elisa Sampedrín translates from Nichita Stãnescu, though she knows no Romanian, and the orthonymic character Erín Moure translates Paul Celan, using not Celan but English transcreations from the language of Celan by Oana Avasilichioaei which she appropriates and reorganizes to create the true translation of a poem by Paul Celan, which exists only in her mind. In this world where corporations copyright human cells, where academics and libraries appropriate works of writers, and where writing itself - moreso than visual art - is limited by expanded notions of plagiarism and ownership, of continuity of copyright for decades that prevents works from influencing art's future, Moure refutes the idea that writing is inspired out of nowhere. Here it is rooted to human interaction, to love and loss, to the art of others, and is dedicated to creating a world where the free irruption of thought is possible, and lineages are acknowledged.

  18. Economic, environmental and social assessment of briquette fuel from agricultural residues in China – A study on flat die briquetting using corn stalk

    International Nuclear Information System (INIS)

    Hu, Jianjun; Lei, Tingzhou; Wang, Zhiwei; Yan, Xiaoyu; Shi, Xinguang; Li, Zaifeng; He, Xiaofeng; Zhang, Quanguo

    2014-01-01

    Biomass can be relatively easily stored and transported compared with other types of renewable energy sources. Crop straw can be converted into densified solid biofuel via briquette fuel technology to expand its possible applications and enhance its utilisation efficiency. However, the potential economic, environmental and social impacts of crop straw briquette fuel need to be assessed before its large-scale use. This paper provides a comprehensive evaluation of these impacts for a fully-operating 2 × 10 4 t/a corn stalk briquette fuel plant in China. The results show that with a life time of 15 years, a purchase price of 150 RMB/t for corn stalk and the current sales price of 400 RMB/t for briquette fuel, the plant has a net present value of 9.6 million RMB or 1.5 million USD, an internal rate of return of 36% and a short investment payback period of 4.4 years. The life cycle greenhouse gas emissions are found to be 323 t CO 2 ,e/year or 1 kg CO 2 ,e/GJ, much lower than that of coal. Additionally, the process reduces pollution by decreasing the amount of corn stalk that is discarded or burnt directly in the field. In terms of social impacts, the use of corn stalk briquetting fuel plant is expected to play an important role in increasing local residents' income, improving rural ecological environments, alleviating energy shortages, guaranteeing energy security, and promoting socialism new rural reconstruction. - Highlights: • A fully-operating 2 × 10 4 t/a corn stalk briquette fuel plant in China is analysed. • The plant has net present value of $1.5 million and payback period of 4.4 years. • Life cycle GHG emissions are 323 t CO 2 ,e/year or 1 kg CO 2 ,e/GJ, much lower than coal. • The plant will also have significant social benefits

  19. The subcellular distribution of the human ribosomal "stalk" components: P1, P2 and P0 proteins

    DEFF Research Database (Denmark)

    Tchórzewski, Marek; Krokowski, Dawid; Rzeski, Wojciech

    2003-01-01

    The ribosomal "stalk" structure is a distinct lateral protuberance located on the large ribosomal subunit in prokaryotic, as well as in eukaryotic cells. In eukaryotes, this ribosomal structure is composed of the acidic ribosomal P proteins, forming two hetero-dimers (P1/P2) attached...

  20. Shea meal and cotton stalk as potential fuels for co-combustion with coal.

    Science.gov (United States)

    Munir, S; Nimmo, W; Gibbs, B M

    2010-10-01

    The efficient management of waste biomass is an important environmental problem in agricultural countries. Often land-fill is the main disposal route with ramifications including CH(4) release having 21 times greater global warming potential per molecule than CO(2). Biomasses are considered to be CO(2)-neutral fuels when combusted. Moreover, they are renewable and covered by the renewable obligation scheme and eligible for certificates in the UK. The overall objective of the investigation is to assess the performance of selected biomass and coal co-firing under two different modes of operation, air-staging and fuel-staging with the benefit of reduced-NO(x) and SO(2) emissions in power plant. The biomasses chosen for the study, shea meal (SM) and cotton stalk (CS) have very different cellulose/lignin compositions and different reported thermal behaviour. A series of experiments have been carried out in a 20 kW, down fired combustor using coal, shea meal-coal and cotton stalk-coal blends under un-staged, air-staged and fuel-staged co-combustion configurations. For air-staging, an optimum value of primary zone stoichiometry SR(1)=0.9 was found. Keeping it fixed, the shea meal and cotton stalk content in the coal-biomass blends was set to 5%, 10% and 15% on thermal basis. NO reductions of 51% and 60% were achieved using SM and CS, respectively, with an optimum thermal biomass blending ratio (BBR) of 10%. The results obtained were compared with un-staged and air-staged results for coal without the addition of biomass. Similarly for fuel-staging, keeping the length of the reburn and burnout zone fixed, SM and CS were evaluated as reductive fuel using different reburn fuel fractions (R(ff)) of 5%, 10%, 15% and 20%. NO reductions of 83% and 84% were obtained with an optimum R(ff) of 15% with an optimum reburn zone stoichiometry of SR(2)=0.8 for both SM and CS, respectively. SO(2) reduction and char burnout efficiency were also evaluated. It was found that addition of

  1. Antifertility effect of betal leaf stalk (Tambul patrabrint): a preliminary experimental study.

    Science.gov (United States)

    Tewari, P V; Chaturvedi, C; Dixit, S N

    1970-01-01

    This study was undertaken to determine possible antifertility properties of the stalk of the betel plant, Piper betle, which is extensively cultivated in warm moist parts of India for its leaves. The thin stalks were dried, powdered, and extracted with alcohol; the residue was used in the study and named betel leaf stalk extract (BLSE). It was macerated with gum acacia, suspended in distilled water, and diluted to 25 mg/ml. The drug was fed by oral intubation. Initially 20 rats were used in 2 groups, one receiving BLSE 50 mg/kg body weight for 10 days and the other vehicle only. Both were caged with males for 15 days. Only 2 of 10 rats receiving BLSE gave birth to litters while 9 of 10 controls delivered. Number of pups was also reduced. In another experiment using 60 female rats to 30 while BLSE at 50 mg/100 gm body weight was fed for 3 days during diestrus to 30 while 30 controls received vehicle only. Successful mating was confirmed by sperm in vaginal smears. 8 of 30 treated rats delivered 3.5 pups each while 29 of 30 controls delivered 7 pups per rat. In a third experiment 10 female rats were given BLSE 50mg/100 gm body weight, 10 vehicle only, and 10 neoclinesterol 150 mcg/100 gm body weight for 4 consecutive days. On Day 5 the animals were sacrificed and weights of uterus and ovaries recorded. Antiestrogenic properties were studied in oophorectomized rats given stilbestrol 150 mcg/100 gm body weight by injection, then fed 150 mcg/100 gm body weight of neoclinesterol or BLSE, 50 mg/100 gm, but the neoclinesterol. Vaginal smears were examined for cornification on Days 2, 3, and 4. Progestational activity was studied in 12 immature female rabbits injected with stilbestrol then treated with BLSE or leutocycline. Tests for estrogenic and antiestrogenic activity of BLSE were negative. A mild progestational activity was found in immature estrogen-primed rabbits but some follicle depressant type action was noted as several graffian follicles were seen in their

  2. Determining the minimum conditions for soda-anthraquinone pulping of kenaf bast, core, and whole stalk fibers

    Science.gov (United States)

    James S. Han; Thomas A. Rymsza

    1999-01-01

    Chemical pulping of kenaf fiber is comparatively new. In this study, bast, core, and whole stalk kenaf fibers were pulped using a soda-AQ pulping process and various pulping conditions. Handsheets were evaluated for density, Canadian standard freeness, brightness, opacity, smoothness, and tensile, burst, and tear indexes and strength. The results indicate that...

  3. Registration of an oilseed sunflower germplasm line HA-BSR1 highly tolerant to Sclerotinia basal stalk rot

    Science.gov (United States)

    Basal stalk rot (BSR) caused by Sclerotinia sclerotiorum (Lib.) de Bary is a devastating disease that causes a significant damage to worldwide sunflower (Helianthus annuus L.) production by reducing seed yield and quality. The objective of this research was to develop highly BSR tolerant sunflower g...

  4. Catalytic conversion of xylose and corn stalk into furfural over carbon solid acid catalyst in γ-valerolactone.

    Science.gov (United States)

    Zhang, Tingwei; Li, Wenzhi; Xu, Zhiping; Liu, Qiyu; Ma, Qiaozhi; Jameel, Hasan; Chang, Hou-min; Ma, Longlong

    2016-06-01

    A novel carbon solid acid catalyst was synthesized by the sulfonation of carbonaceous material which was prepared by carbonization of sucrose using 4-BDS as a sulfonating agent. TEM, N2 adsorption-desorption, elemental analysis, XPS and FT-IR were used to characterize the catalyst. Then, the catalyst was applied for the conversion of xylose and corn stalk into furfural in GVL. The influence of the reaction time, temperature and dosage of catalyst on xylose dehydration were also investigated. The Brønsted acid catalyst exhibited high activity in the dehydration of xylose, with a high furfural yield of 78.5% at 170°C in 30min. What's more, a 60.6% furfural yield from corn stalk was achieved in 100min at 200°C. The recyclability of the sulfonated carbon catalyst was perfect, and it could be reused for 5times without the loss of furfural yields. Copyright © 2016 Elsevier Ltd. All rights reserved.

  5. Stalking and compensation for existential damage. Some remarks starting from the sentences of the Court of Cassation (Supreme Court of November 11, 2008 - Le stalking et l’indemnisation du dommage existentiel. Quelques considérations suite aux jugements de la Cour de Cassation en Chambres Unies du 11 novembre 2008 - Stalking e risarcimento del danno esistenziale. Alcune considerazioni alla luce delle sentenze della Corte di Cassazione a Sezioni Unite dell’11 novembre 2008

    Directory of Open Access Journals (Sweden)

    Florio M.

    2009-05-01

    Full Text Available A few days ago, a regulation against stalking was introduced into the Italian system, inserting the art. 612 bis into the Italian penal code. The author considers the new set of rules, aiming to defend the stalking victim, and the prospects of compensation for damage to the person. Above all, puts more emphasis on the analysis of compensation for existential damage, which is now accepted to be repayable as a result of the important sentences of the Court of Cassation in 2008, when definite criteria were established. From now on, such criteria for a systematic analysis of compensation for existential damage will be a reference point for the Italian Courts.

  6. Effect of thermal and high pressure processing on stability of betalain extracted from red beet stalks.

    Science.gov (United States)

    Dos Santos, Cláudia Destro; Ismail, Marliya; Cassini, Aline Schilling; Marczak, Ligia Damasceno Ferreira; Tessaro, Isabel Cristina; Farid, Mohammed

    2018-02-01

    Red beet stalks are a potential source of betalain, but their pigments are not widely used because of their instability. In the present work, the applicability of high pressure processing (HPP) and high temperature short time (HTST) thermal treatment was investigated to improve betalain stability in extracts with low and high concentrations. The HPP was applied at 6000 bar for 10, 20 and 30 min and HTST treatment was applied at 75.7 °C for 80 s, 81.1 °C for 100 s and 85.7 °C for 120 s, HPP treatment did not show any improvement in the betalain stability. In turn, the degradation rate of the control and the HTST thermal treatment at 85.7 °C for 120 s of the sample with high initial betalain concentration were 1.2 and 0.4 mg of betanin/100 ml of extract per day respectively. Among the treatments studied, HTST was considered the most suitable to maintain betalain stability from red beet stalks.

  7. Rhamnolipid Biosurfactant against Fusarium verticillioides to Control Stalk and Ear Rot Disease of Maize

    Directory of Open Access Journals (Sweden)

    Siddhartha Narayan Borah

    2016-09-01

    Full Text Available Antifungal activity of rhamnolipids (RLs has been widely studied against many plant pathogenic fungi, but not against Fusarium verticillioides, a major pathogen of maize (Zea mays L.. F. verticillioides causes stalk and ear rot of maize or asymptomatically colonizes the plant and ears resulting in moderate to heavy crop loss throughout the world. F. verticillioides produces fumonisin mycotoxins, reported carcinogens, which makes the contaminated ears unsuitable for consumption. In this study, the RL produced using glucose as sole carbon source was characterized by FTIR and LCMS analyses and its antifungal activity against F. verticillioides was evaluated in vitro on maize stalks and seeds. Further, the effect of RL on the mycelia of F. verticillioides was investigated by scanning electron microscopy which revealed visible damage to the mycelial structure as compared to control samples. In planta, treatment of maize seeds with a RL concentration of 50 mg l-1 resulted in improved biomass and fruiting compared to those of healthy control plants and complete suppression of characteristic disease symptoms and colonization of maize by F. verticillioides. The study highlights the potential of RLs to be used for an effective biocontrol strategy against colonization of maize plant by F. verticillioides.

  8. Production of charcoal briquettes from cotton stalk in malawi: methodology for feasibility studies using experiences in Sudan

    NARCIS (Netherlands)

    Onaji, P.B.; Siemons, R.V.

    1993-01-01

    The feasibility of charcoal production from cotton stalks in Malawi was studied based on experience from Sudan. The country relies considerably on biomass fuels. Of the total energy consumption in Malawi of 2.376 MTOE in 1989, 92% was met by biomass (fuelwood: 83.6% and charcoal: 8.3% Petroleum

  9. A stalk of grain and light

    Directory of Open Access Journals (Sweden)

    Erín Moure

    2009-01-01

    Full Text Available http://dx.doi.org/10.5007/2175-8026.2009n56p33 "Stalk of Grain and Light" is an excerpt from O Resplandor (Toronto: Anansi, forthcoming 2010, a book of poetry that explodes notions of authorship and translation. In it, the heteronymic character Elisa Sampedrín translates from Nichita Stãnescu, though she knows no Romanian, and the orthonymic character Erín Moure translates Paul Celan, using not Celan but English transcreations from the language of Celan by Oana Avasilichioaei which she appropriates and reorganizes to create the true translation of a poem by Paul Celan, which exists only in her mind. In this world where corporations copyright human cells, where academics and libraries appropriate works of writers, and where writing itself - moreso than visual art - is limited by expanded notions of plagiarism and ownership, of continuity of copyright for decades that prevents works from influencing art's future, Moure refutes the idea that writing is inspired out of nowhere. Here it is rooted to human interaction, to love and loss, to the art of others, and is dedicated to creating a world where the free irruption of thought is possible, and lineages are acknowledged.

  10. Microbial pretreatment of cotton stalks by Phanerochaete chrysosporium for bioethanol production

    Science.gov (United States)

    Shi, Jian

    Lignocellulosic biomass has been recognized as a widespread, potentially low cost renewable source of mixed sugars for fermentation to fuel ethanol. Pretreatment, as the first step towards conversion of lignocellulose to ethanol, remains one of the main barriers to technical and commercial success of the processing technology. Existing pretreatment methods have largely been developed on the basis of physiochemical technologies which are considered relatively expensive and usually involve adverse environmental impacts. In this study, an environmentally benign alternative, microbial pretreatment using Phanerochaete chrysosporium, was explored to degrade lignin in cotton stalks and facilitate their conversion into ethanol. Two submerged liquid pretreatment techniques (SmC), shallow stationary and agitated cultivation, at three inorganic salt concentrations (no salts, modified salts without Mn2+, modified salts with Mn2+) were compared by evaluating their pretreatment efficiencies. Shallow stationary cultivation with no salt was superior to other pretreatment conditions and gave 20.7% lignin degradation along with 76.3% solids recovery and 29.0% carbohydrate availability over a 14 day period. The influence of substrate moisture content (65%, 75% and 80% M.C. wet-basis), inorganic salt concentration (no salts, modified salts without Mn2+ , modified salts with Mn2+) and culture time (0-14 days) on pretreatment effectiveness in solid state (SSC) systems was also examined. It was shown that solid state cultivation at 75% M.C. without salts was the most preferable pretreatment resulting in 27.6% lignin degradation, 71.1% solids recovery and 41.6% carbohydrate availability over a period of 14 days. A study on hydrolysis and fermentation of cotton stalks treated microbially using the most promising SmC (shallow stationary, no salts) and SSC (75% moisture content, no salts) methods resulted in no increase in cellulose conversion with direct enzyme application (10.98% and 3

  11. Investigation of hydrolysis products in the acetone-butanol fermentation of vegetable agricultural waste materials

    Energy Technology Data Exchange (ETDEWEB)

    Nakhmanovich, B M

    1960-01-01

    Determinations of the fundamental chemical composition of corn stalk, sunflower husk, and hemp scutch by chromatography were reported, e.g. pentoses (1.98, 1.98, 2.01%), hexoses (1.59, 1.72, 2.01% respectively.) and various amino acids (arginine, asparagine, histidine, glutamine, glycine, lysine, proline, serine, tyrosine, threonine, cysteine, cystine, alanine, and aspartic and glutamic acids). The sterilized products from the hydrolysis (pentoses, hexoses) in a combined mixture with a meal mash were normally fermented at 37/sup 0/ in the presence of acetone-butanol bacteria for 40 to 48 hours, yielding 10.46 to 12.50% of acetone, 15.09 to 18.0% of butanol, 3.79 to 6.08% of ethanol (a total yielding being 30 to 42% of solvents).

  12. Cell wall microstructure, pore size distribution and absolute density of hemp shiv

    Science.gov (United States)

    Jiang, Y.; Lawrence, M.; Ansell, M. P.; Hussain, A.

    2018-04-01

    This paper, for the first time, fully characterizes the intrinsic physical parameters of hemp shiv including cell wall microstructure, pore size distribution and absolute density. Scanning electron microscopy revealed microstructural features similar to hardwoods. Confocal microscopy revealed three major layers in the cell wall: middle lamella, primary cell wall and secondary cell wall. Computed tomography improved the visualization of pore shape and pore connectivity in three dimensions. Mercury intrusion porosimetry (MIP) showed that the average accessible porosity was 76.67 ± 2.03% and pore size classes could be distinguished into micropores (3-10 nm) and macropores (0.1-1 µm and 20-80 µm). The absolute density was evaluated by helium pycnometry, MIP and Archimedes' methods. The results show that these methods can lead to misinterpretation of absolute density. The MIP method showed a realistic absolute density (1.45 g cm-3) consistent with the density of the known constituents, including lignin, cellulose and hemi-cellulose. However, helium pycnometry and Archimedes' methods gave falsely low values owing to 10% of the volume being inaccessible pores, which require sample pretreatment in order to be filled by liquid or gas. This indicates that the determination of the cell wall density is strongly dependent on sample geometry and preparation.

  13. Flexible Bionanocomposites from Epoxidized Hemp Seed Oil Thermosetting Resin Reinforced with Halloysite Nanotubes.

    Science.gov (United States)

    Shuttleworth, Peter S; Díez-Pascual, Ana M; Marco, Carlos; Ellis, Gary

    2017-03-23

    Hemp seed (Cannabis sativa L.) oil comprises a variety of beneficial unsaturated triglycerides with well-documented nutritional and health benefits. However, it can become rancid over a relatively short time period, leading to increased industrial costs and waste of a valuable product. The development of sustainable polymers is presented as a strategy, where both the presence of unsaturation and peroxide content could be effectively used to alleviate both the waste and financial burden. After the reaction with peroxyacetic acid, the incorporation of halloysite nanotubes (HNTs), and the subsequent thermal curing, without the need for organic solvents or interfacial modifiers, flexible transparent materials with a low glass-transition temperature were developed. The improvement in the thermal stability and both the static and dynamic mechanical properties of the bionanocomposites were significantly enhanced with the well-dispersed HNT filler. At an optimum concentration of 0.5 wt % HNTs, a simultaneous increase in stiffness, strength, ductility, and toughness was observed in comparison to the unfilled cured resin. These sustainable food-waste-derived bionanocomposites may provide an interesting alternative to petroleum-based materials, particularly for low-load-bearing applications, such as packaging.

  14. Biological Control of Fusarium Stalk Rot of Maize Using Bacillus spp

    Directory of Open Access Journals (Sweden)

    Joon-Hee Han

    2015-12-01

    Full Text Available Maize (Zea mays L. is an economically important crop in worldwide. While the consumption of the maize is steadily increasing, the yield is decreasing due to continuous mono-cultivation and infection of soil-borne fungal pathogens such as Fusarium species. Recently, stalk rot disease in maize, caused by F. subglutinans and F. temperatum has been reported in Korea. In this study, we isolated bacterial isolates in rhizosphere soil of maize and subsequently tested for antagonistic activities against F. subglutinans and F. temperatum. A total of 1,357 bacterial strains were isolated from rhizosphere. Among them three bacterial isolates (GC02, GC07, GC08 were selected, based on antagonistic effects against Fusarium species. The isolates GC02 and GC07 were most efficient in inhibiting the mycelium growth of the pathogens. The three isolates GC02, GC07 and GC08 were identified as Bacillus methylotrophicus, B. amyloliquefaciens and B. thuringiensis using 16S rRNA sequence analysis, respectively. GC02 and GC07 bacterial suspensions were able to suppress over 80% conidial germination of the pathogens. GC02, GC07 and GC08 were capable of producing large quantities of protease enzymes, whereas the isolates GC07 and GC08 produced cellulase enzymes. The isolates GC02 and GC07 were more efficient in phosphate solubilization and siderophore production than GC08. Analysis of disease suppression revealed that GC07 was most effective in suppressing the disease development of stalk rot. It was also found that B. methylotrophicus GC02 and B. amyloliquefaciens GC07 have an ability to inhibit the growth of other plant pathogenic fungi. This study indicated B. methylotrophicus GC02 and B. amyloliquefaciens GC07 has potential for being used for the development of a biological control agent.

  15. [Phenolic foam prepared by lignin from a steam-explosion derived biorefinery of corn stalk].

    Science.gov (United States)

    Wang, Guanhua; Chen, Hongzhang

    2014-06-01

    To increase the integral economic effectiveness, biorefineries of lignocellulosic materials should not only utilize carbohydrates hydrolyzed from cellulose and hemicellulose but also use lignin. We used steam-exploded corn stalk as raw materials and optimized the temperature and alkali concentration in the lignin extraction process to obtain lignin liquor with higher yield and purity. Then the concentrated lignin liquor was used directly to substitute phenol for phenolic foam preparation and the performances of phenolic foam were characterized by microscopic structure analysis, FTIR, compression strength and thermal conductivity detection. The results indicated that, when steam-exploded corn stalk was extracted at 120 degrees C for 2 h by 1% NaOH with a solid to liquid ratio of 1:10, the extraction yield of lignin was 79.67%. The phenolic foam prepared from the concentrated lignin liquor showed higher apparent density and compression strength with the increasing substitution rate of lignin liquor. However, there were not significant differences of thermal conductivity and flame retardant properties by the addition of lignin, which meant that the phenolic foam substituted by lignin liquor was approved for commercial application. This study, which uses alkali-extracted lignin liquor directly for phenolic foam preparation, provides a relatively simple way for utilization of lignin and finally increases the overall commercial operability ofa lignocellulosic biorefinery derived by steam explosion.

  16. Ethanol production from concentrated food waste hydrolysates with yeast cells immobilized on corn stalk

    Energy Technology Data Exchange (ETDEWEB)

    Yan, Shoubao [Huainan Normal Univ., Anhui (China). School of Life Science; Chen, Xiangsong; Wu, Jingyong; Wang, Pingchao [Chinese Academy of Sciences, Hefei (China). Key Lab. of Ion Beam Bio-engineering of Inst. of Plasma Physics

    2012-05-15

    The aim of the present study was to examine ethanol production from concentrated food waste hydrolysates using whole cells of S. cerevisiae immobilized on corn stalks. In order to improve cell immobilization efficiency, biological modification of the carrier was carried out by cellulase hydrolysis. The results show that proper modification of the carrier with cellulase hydrolysis was suitable for cell immobilization. The mechanism proposed, cellulase hydrolysis, not only increased the immobilized cell concentration, but also disrupted the sleek surface to become rough and porous, which enhanced ethanol production. In batch fermentation with an initial reducing sugar concentration of 202.64 {+-} 1.86 g/l, an optimal ethanol concentration of 87.91 {+-} 1.98 g/l was obtained using a modified corn stalk-immobilized cell system. The ethanol concentration produced by the immobilized cells was 6.9% higher than that produced by the free cells. Ethanol production in the 14th cycle repeated batch fermentation demonstrated the enhanced stability of the immobilized yeast cells. Under continuous fermentation in an immobilized cell reactor, the maximum ethanol concentration of 84.85 g/l, and the highest ethanol yield of 0.43 g/g (of reducing sugar) were achieved at hydraulic retention time (HRT) of 3.10 h, whereas the maximum volumetric ethanol productivity of 43.54 g/l/h was observed at a HRT of 1.55 h. (orig.)

  17. Stalk and sucrose yield in response to nitrogen fertilization of sugarcane under reduced tillage

    Directory of Open Access Journals (Sweden)

    Caio Fortes

    2013-01-01

    Full Text Available The objective of this work was to evaluate the agroindustrial production of sugarcane (millable stalks and sucrose yield after successive nitrogen fertilizations of plant cane and ratoons in a reduced tillage system. The experiment was carried out at Jaboticabal, SP, Brazil, on a Rhodic Eutrustox soil, during four consecutive crop cycles (March 2005 to July 2009. Plant cane treatments consisted of N-urea levels (control, 40, 80, and 120 kg ha-1 N + 120 kg ha-1 P2O5 and K2O in furrow application. In the first and second ratoons, the plant cane plots were subdivided in N-ammonium nitrate treatments (control, 50, 100, and 150 kg ha-1 N + 150 kg ha-1 K2O as top dressing over rows. In the third ratoon, N fertilization was leveled to 100 kg ha-1 in all plots, including controls, to detect residual effects of previous fertilizations on the last crop's cycle. Sugarcane ratoon was mechanically harvested. A weighing truck was used to evaluate stalk yield (TCH, and samples were collected in the field for analysis of sugar content (TSH. Increasing N doses and meteorological conditions promote significant responses in TCH and TSH in cane plant and ratoons, in the average and accumulated yield of the consecutive crop cycles.

  18. The amino terminal end determines the stability and assembling capacity of eukaryotic ribosomal stalk proteins P1 and P2.

    Science.gov (United States)

    Camargo, Hendricka; Nusspaumer, Gretel; Abia, David; Briceño, Verónica; Remacha, Miguel; Ballesta, Juan P G

    2011-05-01

    The eukaryotic ribosomal proteins P1 and P2 bind to protein P0 through their N-terminal domain to form the essential ribosomal stalk. A mutational analysis points to amino acids at positions 2 and 3 as determinants for the drastic difference of Saccharomyces cerevisiae P1 and P2 half-life, and suggest different degradation mechanisms for each protein type. Moreover, the capacity to form P1/P2 heterodimers is drastically affected by mutations in the P2β four initial amino acids, while these mutations have no effect on P1β. Binding of P2β and, to a lesser extent, P1β to the ribosome is also seriously affected showing the high relevance of the amino acids in the first turn of the NTD α-helix 1 for the stalk assembly. The negative effect of some mutations on ribosome binding can be reversed by the presence of the second P1/P2 couple in the ribosome, indicating a stabilizing structural influence between the two heterodimers. Unexpectedly, some mutations totally abolish heterodimer formation but allow significant ribosome binding and, therefore, a previous P1 and P2 association seems not to be an absolute requirement for stalk assembly. Homology modeling of the protein complexes suggests that the mutated residues can affect the overall protein conformation. © The Author(s) 2011. Published by Oxford University Press.

  19. Influence of Fiber Bundle Morphology on the Mechanical and Bonding Properties of Cotton Stalk and Mulberry Branch Reconstituted Square Lumber

    Directory of Open Access Journals (Sweden)

    Jing Zhang

    2016-08-01

    Full Text Available The mechanical properties of natural fiber composites can be strengthened in the longitudinal direction if the fiber is formed in a parallel manner. Reconstituted cotton stalk lumber and mulberry branch lumber were fabricated using hot-press technology, and the effects of fiber morphology on their mechanical and bonding properties were investigated. The fiber bundle size had a great influence on the mechanical and bonding properties of the final products. The maximum specific modulus of rupture (MOR and specific modulus of elasticity (MOE of the reconstituted lumber were obtained for medium-size fiber bundles, and the maximum MOR and MOE of reconstituted cotton stalk lumber was 130.3 MPa·g-1·cm-3 and 12.9 GPa·g-1·cm-3, respectively. The maximum MOR and MOE of the mulberry branch lumber was 147.2 MPa·g-1·cm-3 and 14.7 GPa·g-1·cm-3, respectively. Mechanical interlocking structures in the lumber were observed via fluorescence microscopy, showing that phenol-formaldehyde adhesive had penetrated into several cell layers of the fiber bundle under heating and pressure. The adhesive penetration capacity was stronger when the fiber bundles were smaller in size and density. The reconstituted lumber fabricated from both materials exhibited excellent mechanical performance in the parallel direction. Therefore, reconstituted cotton stalk and mulberry branch lumber are attractive potential materials for the construction industry.

  20. Saccharification of sunflower stalks using lignocellulases from a fungal consortium comprising Pholiota adiposa and Armillaria gemina.

    Science.gov (United States)

    Ramachandran, Priyadharshini; Kim, Tae-Su; Dhiman, Saurabh Sudha; Li, Jinglin; Park, Ji-Hyun; Choi, Joon-Ho; Kim, Jae Young; Kim, Dongwook; Lee, Jung-Kul

    2015-09-01

    Lignocellulases from Armillaria gemina and Pholiota adiposa are efficient in hydrolyzing aspen and poplar biomass, respectively. In the present study, lignocellulosic enzymes obtained from a fungal consortium comprising P. adiposa and A. gemina were used for the saccharification of sunflower stalks. Sunflower stalks were thermochemically pretreated using 2 % NaOH at 50 °C for 24 h. The saccharification process parameters including substrate concentration, enzyme loading, pH, and temperature were optimized using response surface methodology to improve the saccharification yield. The highest enzymatic hydrolysis (84.3 %) was obtained using the following conditions: enzyme loading 10 FPU/g-substrate, substrate 5.5 %, temperature 50 °C, and pH 4.5. The hydrolysis yield obtained using the enzymes from the fungal consortium was equivalent to that obtained using a mixture of commercial enzymes Celluclast and Novozyme β-glucosidase. Addition of up to 500 ppm of heavy metal ions (As, Cu, Fe, Mn, Ni, Pb, and Zn) during saccharification did not significantly affect the saccharification yield. Thus, the biomass grown for phytoremediation of heavy metals can be used for the production of reducing sugars followed by ethanol fermentation.

  1. Clinical presentation and outcome of children with central diabetes insipidus associated with a self-limited or transient pituitary stalk thickening, diagnosed as infundibuloneurohypophysitis.

    Science.gov (United States)

    Schaefers, J; Cools, M; De Waele, K; Gies, I; Beauloye, V; Lysy, P; Francois, I; Beckers, D; De Schepper, J

    2017-08-01

    Despite lymphocytic or autoimmune infundibuloneurohypophysitis (INH) is an increasingly recognized aetiology in children with central diabetes insipidus (CDI); clinical data on epidemiology (clinical evolution, predisposing factors, complications), diagnosis and management of this entity are limited and mostly based on published case reports. The aim of this study was to gain a broader insight in the natural history of this disease by analysing the clinical presentation, radiological pituitary stalk changes, associated autoimmunity and hormonal deficiencies in children with CDI and a self-limiting or transient stalk thickening (ST), diagnosed as autoimmune infundibuloneurohypophysitis, during the last 15 years in four Belgian university hospitals. The medical files of nine CDI patients with a ST at initial presentation and no signs of Langerhans cell histiocytosis or germinoma at presentation and/or during follow-up of more than 1.5 years were reviewed. Age at presentation ranged from 3 to 14 years. Two patients had a positive family history of autoimmunity. Three children presented with associated growth failure, two with nausea and one with long-standing headache. Median maximal diameter of the stalk was 4.6 mm (2.7-10 mm). Four patients had extra-pituitary brain anomalies, such as cysts. One patient had central hypothyroidism, and another had a partial growth hormone deficiency at diagnosis. Within a mean follow-up of 5.4 (1.5-15) years, stalk thickening remained unchanged in two patients, regressed in one and normalized in six children. CDI remained in all, while additional pituitary hormone deficiencies developed in only one patient. In this series of children INH with CDI as initial presentation, CDI was permanent and infrequently associated with anterior pituitary hormone deficiencies, despite a frequent association with nonstalk cerebral lesions. © 2017 The Authors. Clinical Endocrinology Published by John Wiley & Sons Ltd.

  2. Fabrication of the novel hydrogel based on waste corn stalk for removal of methylene blue dye from aqueous solution

    Science.gov (United States)

    Ma, Dongzhuo; Zhu, Baodong; Cao, Bo; Wang, Jian; Zhang, Jianwei

    2017-11-01

    The novel hydrogel based on waste corn stalk was synthetized by aqueous solution polymerization technique with functional monomers in the presence of organic montmorillonite (OMMT) under ultrasonic. In this study, batch adsorption experiments were carried out to research the effect of initial dye concentration, the dosage of hydrogel, stirring speed, contact time and temperature on the adsorption of methylene blue (MB) dye. The adsorption process was best described by the pseudo-second-order kinetic model, which confirmed that it should be a chemical process. Furthermore, we ascertained the rate controlling step by establishing the intraparticle diffusion model and the liquid film diffusion model. The adsorption and synthesis mechanisms were vividly depicted in our work as well. Structural and morphological characterizations by virtue of FTIR, FESEM, and Biomicroscope supported the relationship between the adsorption performance and material's microstructure. This research is a valuable contribution for the environmental protection, which not only converts waste corn stalks into functional materials, but improves the removal of organic dye from sewage water.

  3. Cytotoxic Triterpenoids from the Stalks of Microtropis triflora.

    Science.gov (United States)

    Zhang, Xiao-Wei; Wang, Kui-Wu; Zhou, Man-Qing

    2017-07-01

    Bioassay-guided phytochemical investigation of the stalks of Microtropis triflora Merr. & F.L. Freeman led to the isolation of ten triterpenes 1 - 10, including one novel compound 3,24-epoxy-2α,24-dihydroxyfriedelan-29-oic acid (1). Their chemical structures were identified on the basis of spectroscopic analysis, including HR-ESI mass spectrometry, 1D- and 2D-NMR ( 1 H, 13 C, 1 H, 1 H-COSY, HSQC, HMBC, and NOESY), and by comparison with the data reported. The cytotoxicities of compounds 1 - 10 against a panel of cultured human tumor cell lines (Bcap37, SMMC7721, HeLa, CNE) were evaluated. The new compound 1 showed moderate anti-tumor activities with IC 50 values of 39.22, 29.24, 23.28, and 68.81 μm/ml, respectively. These results might be helpful for explaining the use of M. triflora in traditional medicine. Triterpenes are characteristic of Microtropis genus and could be useful as potential chemotaxonomic markers. © 2017 Wiley-VHCA AG, Zurich, Switzerland.

  4. A novel wild-type Saccharomyces cerevisiae strain TSH1 in scaling-up of solid-state fermentation of ethanol from sweet sorghum stalks.

    Science.gov (United States)

    Du, Ran; Yan, Jianbin; Feng, Quanzhou; Li, Peipei; Zhang, Lei; Chang, Sandra; Li, Shizhong

    2014-01-01

    The rising demand for bioethanol, the most common alternative to petroleum-derived fuel used worldwide, has encouraged a feedstock shift to non-food crops to reduce the competition for resources between food and energy production. Sweet sorghum has become one of the most promising non-food energy crops because of its high output and strong adaptive ability. However, the means by which sweet sorghum stalks can be cost-effectively utilized for ethanol fermentation in large-scale industrial production and commercialization remains unclear. In this study, we identified a novel Saccharomyces cerevisiae strain, TSH1, from the soil in which sweet sorghum stalks were stored. This strain exhibited excellent ethanol fermentative capacity and ability to withstand stressful solid-state fermentation conditions. Furthermore, we gradually scaled up from a 500-mL flask to a 127-m3 rotary-drum fermenter and eventually constructed a 550-m3 rotary-drum fermentation system to establish an efficient industrial fermentation platform based on TSH1. The batch fermentations were completed in less than 20 hours, with up to 96 tons of crushed sweet sorghum stalks in the 550-m3 fermenter reaching 88% of relative theoretical ethanol yield (RTEY). These results collectively demonstrate that ethanol solid-state fermentation technology can be a highly efficient and low-cost solution for utilizing sweet sorghum, providing a feasible and economical means of developing non-food bioethanol.

  5. Changes of the surface structure of corn stalk in the cooking process with active oxygen and MgO-based solid alkali as a pretreatment of its biomass conversion.

    Science.gov (United States)

    Pang, Chunsheng; Xie, Tujun; Lin, Lu; Zhuang, Junping; Liu, Ying; Shi, Jianbin; Yang, Qiulin

    2012-01-01

    This study presents a novel, efficient and environmentally friendly process for the cooking of corn stalk that uses active oxygen (O2 and H2O2) and a recoverable solid alkali (MgO). The structural changes on the surface of corn stalk before and after cooking were characterized by attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM) techniques. The results showed that lignin and extractives were effectively removed, especially those on the surface of corn stalk. Additionally, the changes included becoming fibrillar, the exposure of cellulose and hemi-cellulose and the pitting corrosion on the surface, etc. The results also showed that the removal reaction is from outside to inside, but the main reaction is possibly on the surface. Furthermore, the results of active oxygen cooking with a solid alkali are compared with those of alkaline cooking in the paper. Copyright © 2011 Elsevier Ltd. All rights reserved.

  6. Investigation on the Effect of Kenaf Core and Stalk Fiber on the Medium Density Fiber Board Properties Made of Poplar Fibers

    Directory of Open Access Journals (Sweden)

    Fahimeh SH.Alizadeh

    2012-01-01

    Full Text Available In order to optimize the use of material non-forest resources, in this study the possibility of using the kenaf stalk fibers mixed with poplar fibers in producing medium density fiber board was considered. Variable factors such as density at two levels (0.55, 0.75 g/cm3 and the percentage incorporation of fiber (%50 poplar fibers, - %50 kenaf core fiber, %50 poplar fiber, -% 50 kenaf stalk fiber and %100 poplar fibers were considered. Steaming time and temperature (175°C, 10min, press time and temperature (5 min, 175°C, Pressing pressure (30 kg/cm3, fiber cake moisture (%12 and urea-formaldehyde resin with Concentration of %50 of the study factors were fixed. Results show that adding kenaf core fibers to the poplar fibers increases modulus of elasticity and water absorption but thickness swelling reduces. Increased density in board made with kenaf core has caused increase in bending strength, modulus of elasticity and internal bond strength and their water absorption and thickness swelling after 2 and 24 hours were competitive with poplar (MDF. On the other hand Populus fiber– kenaf stalk board mechanical and physical properties were competitive with (MDF board made of %100 poplar fibers. Finally we can say that according to the statistical analysis, the best treatment in this study was using kenaf core fibers, in making poplar (MDF with 0.75 g/cm3 density.

  7. Exploring of Agro Waste (Pineapple Leaf, Corn Stalk, and Napier Grass by Chemical Composition and Morphological Study

    Directory of Open Access Journals (Sweden)

    Angzzas Sari Mohd Kassim

    2013-12-01

    Full Text Available Malaysia is a country that is a rich source of agricultural waste material. Three different crops were studied here, including pineapple (Ananas comosus leaf, corn (Zea mays stalk, and Napier grass (Pennisetum purpureum. These crops are characterized as agricultural waste materials in Malaysia and have a high potential to be used as alternative fibers for the paper making industry. The objective of this work was to analyze the chemical composition of pineapple leaf, corn stalk, and Napier grass and to investigate the fiber morphology of these crops. The chemical components analyzed include the following: cellulose (Kurshner-Hoffner method, holocellulose (chlorination method, hemicellulose (chlorination method, ash content (TAPPI method T211-om-93, lignin content (TAPPI method T222-om-98, and soluble sodium hydroxide (TAPPI method T203-om-98. All handsheets morphologies were observed using scanning electron microscopy (SEM. Results indicated each crop has the potential for use as a fiber in paper making. SEM images indicated a condensed composition of the fiber structure. The observed chemical composition and morphology of these three crops indicate their suitability for use as fiber sources for the paper industry.

  8. Two-dimensional hierarchical porous carbon composites derived from corn stalks for electrode materials with high performance

    International Nuclear Information System (INIS)

    Xu, Haitao; Zhang, Huijuan; Ouyang, Ya; Liu, Li; Wang, Yu

    2016-01-01

    Highlights: • Novel 2D porous carbon sheets from cornstalks are obtained for the first time. • The hierarchical porous carbon nansheets are gained by chemical activation. • The porous structure facilitates ion transfer and Li-ion absorption. • The strategy are applied to both cathode and anode electrode materials. • The porous nanocomposites exhibit excellent electrochemical performance. - Abstract: Herein, we propose a novel and green strategy to convert crop stalks waste into hierarchical porous carbon composites for electrode materials of lithium-ion batteries. In the method, the sustainable crop stalks, an abundant agricultural byproduct, is recycled and treated by a simple and clean chemical activation process. Afterwards, the obtained porous template is adopted for large-scale production of high-performance anode and cathode materials for lithium-ion batteries. Due to the large surface area, hierarchical porous structures and subsize of the functional particles, the electrode materials manifest excellent electrochemical performance. In particular, the prepared TiO 2 /C composite presents a reversible specific capacity of 203 mAh g −1 after 200 cycles. Our results demonstrate that the sheetlike composites show remarkable cycling stability, high specific capacity and excellent rate ability, and thus hold promise for commercializing the high-performance electrode materials as the advanced lithium-ion batteries.

  9. Degradation of corn stalk by the composite microbial system of MC1

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The composite microbial system of MC1 was used to degrade corn stalk in order to determine properties of the degraded products as well as bacterial composition of MC1. Results indicated that the pH of the fermentation broth was typical of lignocellulose degradatioin by MC1, decreasing in the early phase and increasing in later stages of the degradation. The microbial biomass peaked on the day 3 after degradation. The MC1 effeciently degraded the corn stalk by nearly 70% during which its cellulose content decreased by 71.2%, hemicellulose by 76.5% and lignin by 24.6%. The content of water-soluble carbohydrates (WSC) in the fermentation broth increased progressively during the first three days, and decreased thereafter, suggesting an accumulation of WSC in the early phase of the degradation process. Total levels of various volatile products peaked in the third day after degradation , and 7 types of volatile products were detected in the fermentation broth. These were ethanol, acetic acid, 1,2-ethanediol, propanoic acid, butanoic acid, 3-methyl-butanoic acid and glycerine. Six major compounds were quantitatively analysed and the contents of each compound were ethanol (0.584 g/L), acetic acid (0.735 g/L), 1,2-ethanediol (0.772 g/L), propanoic acid (0.026 g/L), butanoic acid (0.018 g/L) and glycerine (4.203 g/L). Characterization of bacterial cells collected from the culture solution, based on 16S rDNA PCR-DGGE analysis of DNAs, showed that the composition of bacterial community in MC1 coincided basically with observations from previous studies. This indicated that the structure of MC1 is very stable during degradation of different lignocellulose materials.

  10. Pyrolysis of corn stalk biomass briquettes in a scaled-up microwave technology.

    Science.gov (United States)

    Salema, Arshad Adam; Afzal, Muhammad T; Bennamoun, Lyes

    2017-06-01

    Pyrolysis of corn stalk biomass briquettes was carried out in a developed microwave (MW) reactor supplied with 2.45GHz frequency using 3kW power generator. MW power and biomass loading were the key parameters investigated in this study. Highest bio-oil, biochar, and gas yield of 19.6%, 41.1%, and 54.0% was achieved at different process condition. In terms of quality, biochar exhibited good heating value (32MJ/kg) than bio-oil (2.47MJ/kg). Bio-oil was also characterised chemically using FTIR and GC-MS method. This work may open new dimension towards development of large-scale MW pyrolysis technology. Copyright © 2017 Elsevier Ltd. All rights reserved.

  11. Origin of samples of Cannabis sativa through insect fragments associated with compacted hemp drug in South America

    Directory of Open Access Journals (Sweden)

    Marcos Patrício Macedo

    2013-06-01

    Full Text Available Origin of samples of Cannabis sativa through insect fragments associated with compacted hemp drug in South America. Insects associated with a seizure of Cannabis sativa L. may indicate the origin of the illicit drug. Nevertheless, no work regarding this subject has been previously published for South America. In the present investigation, seven kilograms of vegetal material (C. sativa were inspected for insect fragments. Three species were identified and used to test the origin of the seizure of cannabis plant material: Euschistus heros (Fabricius, 1794, Thyanta perditor (Fabricius, 1794 (Heteroptera, Pentatomidae, and Cephalotes pusillus (Klug, 1824 (Hymenoptera, Formicidae. These insect species restricted the geographic origin of the drug to the Neotropical region, and their distribution patterns showed an overlap of the State of Mato Grosso (Brazil, Argentina, and Paraguay. Based on this information, two of the three major C. sativa growing areas in South America were excluded: (1 the Colombian territory and (2 northeastern Brazil.

  12. A novel wild-type Saccharomyces cerevisiae strain TSH1 in scaling-up of solid-state fermentation of ethanol from sweet sorghum stalks.

    Directory of Open Access Journals (Sweden)

    Ran Du

    Full Text Available The rising demand for bioethanol, the most common alternative to petroleum-derived fuel used worldwide, has encouraged a feedstock shift to non-food crops to reduce the competition for resources between food and energy production. Sweet sorghum has become one of the most promising non-food energy crops because of its high output and strong adaptive ability. However, the means by which sweet sorghum stalks can be cost-effectively utilized for ethanol fermentation in large-scale industrial production and commercialization remains unclear. In this study, we identified a novel Saccharomyces cerevisiae strain, TSH1, from the soil in which sweet sorghum stalks were stored. This strain exhibited excellent ethanol fermentative capacity and ability to withstand stressful solid-state fermentation conditions. Furthermore, we gradually scaled up from a 500-mL flask to a 127-m3 rotary-drum fermenter and eventually constructed a 550-m3 rotary-drum fermentation system to establish an efficient industrial fermentation platform based on TSH1. The batch fermentations were completed in less than 20 hours, with up to 96 tons of crushed sweet sorghum stalks in the 550-m3 fermenter reaching 88% of relative theoretical ethanol yield (RTEY. These results collectively demonstrate that ethanol solid-state fermentation technology can be a highly efficient and low-cost solution for utilizing sweet sorghum, providing a feasible and economical means of developing non-food bioethanol.

  13. Harassment, stalking, threats and attacks targeting New Zealand politicians: A mental health issue.

    Science.gov (United States)

    Every-Palmer, Susanna; Barry-Walsh, Justin; Pathé, Michele

    2015-07-01

    Due to the nature of their work, politicians are at greater risk of stalking, harassment and attack than the general population. The small, but significantly elevated risk of violence to politicians is predominantly due not to organised terrorism or politically motivated extremists but to fixated individuals with untreated serious mental disorders, usually psychosis. Our objective was to ascertain the frequency, nature and effects of unwanted harassment of politicians in New Zealand and the possible role of mental illness in this harassment. New Zealand Members of Parliament were surveyed, with an 84% response rate (n = 102). Quantitative and qualitative data were collected on Parliamentarians' experiences of harassment and stalking. Eighty-seven percent of politicians reported unwanted harassment ranging from disturbing communications to physical violence, with most experiencing harassment in multiple modalities and on multiple occasions. Cyberstalking and other forms of online harassment were common, and politicians felt they (and their families) had become more exposed as a result of the Internet. Half of MPs had been personally approached by their harassers, 48% had been directly threatened and 15% had been attacked. Some of these incidents were serious, involving weapons such as guns, Molotov cocktails and blunt instruments. One in three politicians had been targeted at their homes. Respondents believed the majority of those responsible for the harassment exhibited signs of mental illness. The harassment of politicians in New Zealand is common and concerning. Many of those responsible were thought to be mentally ill by their victims. This harassment has significant psychosocial costs for both the victim and the perpetrator and represents an opportunity for mental health intervention. © The Royal Australian and New Zealand College of Psychiatrists 2015.

  14. 24 CFR 5.2005 - Protection of victims of domestic violence, dating violence, and stalking in public and Section 8...

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Protection of victims of domestic violence, dating violence, and stalking in public and Section 8 housing. 5.2005 Section 5.2005 Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development GENERAL HUD PROGRAM REQUIREMENTS; WAIVERS Protection for...

  15. Intimate Partner Violence Perpetration by Court-Ordered Men: Distinctions and Intersections among Physical Violence, Sexual Violence, Psychological Abuse, and Stalking

    Science.gov (United States)

    Basile, Kathleen C.; Hall, Jeffrey E.

    2011-01-01

    This study assessed the construct validity of two different measurement models of male partners' perpetration of physical violence, sexual violence, psychological abuse, and stalking against intimate partners. Data were obtained from a sample of 340 men arrested for physical assault of a female spouse or partner and court ordered into batterer…

  16. Crystal Structure of the 23S rRNA Fragment Specific to r-Protein L1 and Designed Model of the Ribosomal L1 Stalk from Haloarcula marismortui

    Directory of Open Access Journals (Sweden)

    Azat Gabdulkhakov

    2017-02-01

    Full Text Available The crystal structure of the 92-nucleotide L1-specific fragment of 23S rRNA from Haloarcula marismortui (Hma has been determined at 3.3 Å resolution. Similar to the corresponding bacterial rRNA fragments, this structure contains joined helix 76-77 topped by an approximately globular structure formed by the residual part of the L1 stalk rRNA. The position of HmaL1 relative to the rRNA was found by its docking to the rRNA fragment using the L1-rRNA complex from Thermus thermophilus as a guide model. In spite of the anomalous negative charge of the halophilic archaeal protein, the conformation of the HmaL1-rRNA interface appeared to be very close to that observed in all known L1-rRNA complexes. The designed structure of the L1 stalk was incorporated into the H. marismortui 50S ribosomal subunit. Comparison of relative positions of L1 stalks in 50S subunits from H. marismortui and T. thermophilus made it possible to reveal the site of inflection of rRNA during the ribosome function.

  17. Extraction and Hydrophobic Modification of Cotton Stalk Bark Fiber

    Directory of Open Access Journals (Sweden)

    Ya-Yu Li

    2016-01-01

    Full Text Available Cotton stalk bark fiber (CSBF was extracted at high temperature and under high pressure, under the condition of the alkali content of 11 wt%. Experimental results proved that the extraction yield of CSBF was 27.3 wt%, and the residual alkali concentration was 2.1 wt%. Then five kinds of modifiers including methyl methacrylate (MMA, MMA plus initiator, epoxy propane, copper ethanolamine, and silane coupling agent were chosen to modify the surface of CSBF. It was found by measuring water retention value (WRV that these five kinds of modifiers were all effective and the silane coupling agent was best modifier among all. The optimal modifying conditions of silane coupling agent were obtained: modifier concentration was 5%, the mixing temperature was 20°C, the mixing time was 1 h, and vacuum drying time was 1 h. Under the optimal condition, the WRV of the modified CSBF was 89%. It is expected that these modified CSBF may be a filler with strengthening effect in wood plastic composites (WPC fields.

  18. The expression, purification, crystallization and preliminary X-ray analysis of a subcomplex of the peripheral stalk of ATP synthase from bovine mitochondria

    International Nuclear Information System (INIS)

    Silvester, Jocelyn A.; Kane Dickson, Veronica; Runswick, Michael J.; Leslie, Andrew G. W.; Walker, John E.

    2006-01-01

    A recombinant subcomplex of the peripheral stalk or stator domain of the ATP synthase from bovine mitochondria has been crystallized and a native data set has been collected to 2.8 Å resolution. A subcomplex of the peripheral stalk or stator domain of the ATP synthase from bovine mitochondria has been expressed to high levels in a soluble form in Escherichia coli. The subcomplex consists of residues 79–184 of subunit b, residues 1–124 of subunit d and the entire F 6 subunit (76 residues). It has been purified and crystallized by vapour diffusion. The morphology and diffraction properties of the crystals of the subcomplex were improved by the presence of thioxane or 4-methylpyridine in the crystallization liquor. With a synchrotron-radiation source, these crystals diffracted to 2.8 Å resolution. They belong to the monoclinic space group P2 1

  19. Fast pyrolysis product distribution of biopretreated corn stalk by methanogen.

    Science.gov (United States)

    Wang, Tipeng; Ye, Xiaoning; Yin, Jun; Jin, Zaixing; Lu, Qiang; Zheng, Zongming; Dong, Changqing

    2014-10-01

    After pretreated by methanogen for 5, 15 and 25 days, corn stalk (CS) were pyrolyzed at 250, 300, 350, 400, 450 and 500 °C by Py-GC/MS and product distribution in bio-oil was analyzed. Results indicated that methanogen pretreatment changed considerably the product distribution: the contents of sugar and phenols increased; the contents of linear carbonyls and furans decreased; the contents of linear ketones and linear acids changed slightly. Methanogen pretreatment improved significantly the pyrolysis selectivity of CS to phenols especially 4-VP. At 250 °C, the phenols content increased from 42.25% for untreated CS to 79.32% for biopretreated CS for 5 days; the 4-VP content increased from 28.6% to 60.9%. Increasing temperature was contributed to convert more lignin into 4-VP, but decreased its content in bio-oil due to more other chemicals formed. The effects of biopretreatment time on the chemicals contents were insignificant. Copyright © 2014 Elsevier Ltd. All rights reserved.

  20. Adhesive proteins of stalked and acorn barnacles display homology with low sequence similarities.

    Directory of Open Access Journals (Sweden)

    Jaimie-Leigh Jonker

    Full Text Available Barnacle adhesion underwater is an important phenomenon to understand for the prevention of biofouling and potential biotechnological innovations, yet so far, identifying what makes barnacle glue proteins 'sticky' has proved elusive. Examination of a broad range of species within the barnacles may be instructive to identify conserved adhesive domains. We add to extensive information from the acorn barnacles (order Sessilia by providing the first protein analysis of a stalked barnacle adhesive, Lepas anatifera (order Lepadiformes. It was possible to separate the L. anatifera adhesive into at least 10 protein bands using SDS-PAGE. Intense bands were present at approximately 30, 70, 90 and 110 kilodaltons (kDa. Mass spectrometry for protein identification was followed by de novo sequencing which detected 52 peptides of 7-16 amino acids in length. None of the peptides matched published or unpublished transcriptome sequences, but some amino acid sequence similarity was apparent between L. anatifera and closely-related Dosima fascicularis. Antibodies against two acorn barnacle proteins (ab-cp-52k and ab-cp-68k showed cross-reactivity in the adhesive glands of L. anatifera. We also analysed the similarity of adhesive proteins across several barnacle taxa, including Pollicipes pollicipes (a stalked barnacle in the order Scalpelliformes. Sequence alignment of published expressed sequence tags clearly indicated that P. pollicipes possesses homologues for the 19 kDa and 100 kDa proteins in acorn barnacles. Homology aside, sequence similarity in amino acid and gene sequences tended to decline as taxonomic distance increased, with minimum similarities of 18-26%, depending on the gene. The results indicate that some adhesive proteins (e.g. 100 kDa are more conserved within barnacles than others (20 kDa.

  1. Application of sunflower stalk-carbon nitride nanosheets as a green sorbent in the solid-phase extraction of polycyclic aromatic hydrocarbons followed by high-performance liquid chromatography.

    Science.gov (United States)

    Marzi Khosrowshahi, Elnaz; Razmi, Habib

    2018-02-08

    A green biocomposite of sunflower stalks and graphitic carbon nitride nanosheets has been applied as a solid-phase extraction adsorbent for sample preparation of five polycyclic aromatic hydrocarbons in different solutions using high-performance liquid chromatography with ultraviolet detection. Before the modification, sunflower stalks exhibited relatively low adsorption to the polycyclic aromatic hydrocarbons extraction. The modified sunflower stalks showed increased adsorption to the analytes extraction due to the increase in surface and existence of a π-π interaction between the analytes and graphitic carbon nitride nanosheets on the surface. Under the optimal conditions, the limits of detection and quantification for five polycyclic aromatic hydrocarbons compounds could reach 0.4-32 and 1.2-95 ng/L, respectively. The method accuracy was evaluated using recovery measurements in spiked real samples and good recoveries from 71 to 115% with relative standard deviations of polycyclic aromatic hydrocarbons determination in various samples-well water, tap water, soil, vegetable, and barbequed meat (kebab)-with analytes contents ranging from 0.065 to 13.3 μg/L. The prepared green composite as a new sorbent has some advantages including ease of preparation, low cost, and good reusability. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  2. Could a deletion in neuraminidase stalk strengthen human tropism of the novel avian influenza virus H7N9 in China, 2013?

    Science.gov (United States)

    Chen, Liang; Zhu, Feng; Xiong, Chenglong; Zhang, Zhijie; Jiang, Lufang; Chen, Yue; Zhao, Genming; Jiang, Qingwu

    2015-01-20

    Objective. A novel avian influenza A virus (AIV) H7N9 subtype which emerged in China in 2013 caused worldwide concern. Deletion of amino-acids 69 to 73 in the neuraminidase stalk was its most notable characteristic. This study is aimed to discuss the tropism and virulence effects of this deletion. Neuraminidase gene sequences of N9 subtype were collected from NCBI and GISAID. MEGA6.0, Stata12.0, and UCSF Chimera were employed for sequence aligning, significance testing, and protein tertiary structure homology modeling. A total of 736 sequences were obtained; there were 81 human isolates of the novel AIV H7N9, of which 79 had the deletion. Among all the 654 avian origin sequences, only 43 had the deletion (p deletion obviously changed the spatial direction of neuraminidase. The deletion in neuraminidase stalk could have strengthened human tropism of the novel AIV H7N9, as well as its virulence.

  3. Chemical constituents from roots and leaf stalks of acai (Euterpe precatoria Mart., Arecaceae)

    International Nuclear Information System (INIS)

    Galotta, Ana Lucia Queiroz de Assis; Boaventura, Maria Amelia Diamantino

    2005-01-01

    Phytochemical investigation of the hexane, ethyl acetate and methanolic extracts of roots and leaf stalks of Euterpe precatoria Mart. (acai), afforded stigmast-4-en-6β-ol-3-one (3); p-hydroxy benzoic acid (4); 3β-O-D-glucopyranosyl-sitosterol (5); β-sitosterol palmitate (6); mixtures of β-sitosterol and stigmasterol (1 and 2), α-, β-amyrin and lupeol (7, 8 and 9), friedelin-3-one and 28-hydroxy-friedelin-3-one (10 and 11) and α-, β-D-glucose (12, 13). Except for 1, 2 and 4, the other isolated constituents are described in the genus for the first time. Compounds 3 and 5 gave good results in the brine shrimp bioassay, which detects compounds with potential uses as antitumor agents, pesticides, etc.. (author)

  4. A new stalked filter-feeder from the middle Cambrian Burgess Shale, British Columbia, Canada.

    Directory of Open Access Journals (Sweden)

    Lorna J O'Brien

    Full Text Available Burgess Shale-type deposits provide invaluable insights into the early evolution of body plans and the ecological structure of Cambrian communities, but a number of species, continue to defy phylogenetic interpretations. Here we extend this list to include a new soft-bodied animal, Siphusauctum gregarium n. gen. and n. sp., from the Tulip Beds (Campsite Cliff Shale Member, Burgess Shale Formation of Mount Stephen (Yoho National Park, British Columbia. With 1,133 specimens collected, S. gregarium is clearly the most abundant animal from this locality.This stalked animal (reaching at least 20 cm in length, has a large ovoid calyx connected to a narrow bilayered stem and a small flattened or bulb-like holdfast. The calyx is enclosed by a flexible sheath with six small openings at the base, and a central terminal anus near the top encircled by indistinct openings. A prominent organ, represented by six radially symmetrical segments with comb-like elements, surrounds an internal body cavity with a large stomach, conical median gut and straight intestine. Siphusauctum gregarium was probably an active filter-feeder, with water passing through the calyx openings, capturing food particles with its comb-like elements. It often occurs in large assemblages on single bedding planes suggesting a gregarious lifestyle, with the animal living in high tier clusters. These were probably buried en masse more or less in-situ by rapid mud flow events.Siphusauctum gregarium resembles Dinomischus, another Cambrian enigmatic stalked animal. Principal points of comparison include a long stem with a calyx containing a visceral mass and bract-like elements, and a similar lifestyle albeit occupying different tiering levels. The presence in both animals of a digestive tract with a potential stomach and anus suggest a grade of organization within bilaterians, but relationships with extant phyla are not straightforward. Thus, the broader affinities of S. gregarium remain

  5. Analysis of microbial taxonomical groups present in maize stalks suppressive to colonization by toxigenic Fusarium spp.: A strategy for the identification of potential antagonists

    NARCIS (Netherlands)

    Köhl, J.; Lombaers-van der Plas, C.H.; Moretti, A.; Bandyopadhyay, R.; Somma, S.; Kastelein, P.

    2015-01-01

    Pink ear rot of maize caused by Fusarium verticillioides, Fusariumproliferatum and Fusariumgraminearumcan lead to severe yield losses and contamination of grain with a range of mycotoxins. Maize stalks colonized by Fusarium spp. are the main primary inoculum source for Fusarium incited epidemics in

  6. CX3CL1, a chemokine finely tuned to adhesion: critical roles of the stalk glycosylation and the membrane domain

    Directory of Open Access Journals (Sweden)

    Mariano A. Ostuni

    2014-11-01

    Full Text Available The multi-domain CX3CL1 transmembrane chemokine triggers leukocyte adherence without rolling and migration by presenting its chemokine domain (CD to its receptor CX3CR1. Through the combination of functional adhesion assays with structural analysis using FRAP, we investigated the functional role of the other domains of CX3CL1, i.e., its mucin stalk, transmembrane domain, and cytosolic domain. Our results indicate that the CX3CL1 molecular structure is finely adapted to capture CX3CR1 in circulating cells and that each domain has a specific purpose: the mucin stalk is stiffened by its high glycosylation to present the CD away from the membrane, the transmembrane domain generates the permanent aggregation of an adequate amount of monomers to guarantee adhesion and prevent rolling, and the cytosolic domain ensures adhesive robustness by interacting with the cytoskeleton. We propose a model in which quasi-immobile CX3CL1 bundles are organized to quickly generate adhesive patches with sufficiently high strength to capture CX3CR1+ leukocytes but with sufficiently low strength to allow their patrolling behavior.

  7. Selective isolation and characterization of agriculturally beneficial endopytic bacteria from wild hemp using canola

    International Nuclear Information System (INIS)

    Afzal, I.; Iqrar, I.

    2015-01-01

    Endophytic bacteria can provide a useful alternative to synthetic fertilizers to improve plant growth. Wild plants are little investigated as a source of growth promoting endophytic bacteria for commercial application to crops. In present study, endophytic bacteria were isolated from Cannabis sativa L. (hemp) using two different methods to examine their ability to promote canola growth. Besides direct isolation from the roots, endophytic bacteria were also selectively isolated from the rhizosphere of C. sativa using canola. Under gnotobiotic conditions, six bacteria from the selective isolation significantly improved canola root growth, as compared to the two bacteria isolated from direct method. Overall, three isolates performed distinctly well, namely, Pantoea vagans MOSEL-t13, Pseudomonas geniculata MOSEL-tnc1, and Serratia marcescens MOSEL-w2. These bacteria tolerated high salt concentrations and promoted canola growth under salt stress. Further, the isolated bacteria possessed plant growth promoting traits like IAA production, phosphate solubilization, and siderophore production. Most isolates produced plant cell-wall degrading enzymes, cellulase and pectinase. Some isolates were also effective in hindering the growth of two phytopathogenic fungi in dual culture assay, and displayed chitinase and protease activity. Paenibacillus sp. MOSEL-w13 displayed the greatest antifungal activity among all the isolates. Present findings conclude that wild plants can be a good source for isolating beneficial microbes, and validates the employed selective isolation for improved isolation of plant-beneficial endophytic bacteria. (author)

  8. OXIDATION AND SULFOMETHYLATION OF ALKALI-EXTRACTED LIGNIN FROM CORN STALK

    Directory of Open Access Journals (Sweden)

    Huiran Wu,

    2012-05-01

    Full Text Available A lignosulfonate was prepared from alkali-extracted corn stalk lignin (AEL by oxidation under mild conditions and sulfomethylation. The oxidized AEL exhibited lower molecular weight, narrower molecular weight distribution, and higher phenolic hydroxyl content than AEL, demonstrating that oxidized AEL was more reactive than those before oxidation. The content of sulfonic groups was significantly increased with the increase in sodium sulphite to AEL ratio, while the content slightly decreased when the ratio was above 1:1. During the sulfomethylation, the content of sulfonic groups increased with time and then achieved a constant level with the increase in time. The content of sulfonic groups reached 1.29 mmol/g, the maximum value, at 5 h and a sodium sulphite to AEL ratio of 1:1. The solubility of AEL was obviously improved by sulfomethylation with the increase in the content of sulfonic groups. The surface activity of AEL was improved after sulfomethylation. The sulfomethylation products exhibited good dispersibility and showed potential for use as a dye dispersant.

  9. Light absorption of organic aerosol from pyrolysis of corn stalk

    Science.gov (United States)

    Li, Xinghua; Chen, Yanju; Bond, Tami C.

    2016-11-01

    Organic aerosol (OA) can absorb solar radiation in the low-visible and ultra-violet wavelengths thereby modifying radiative forcing. Agricultural waste burning emits a large quantity of organic carbon in many developing countries. In this work, we improved the extraction and analysis method developed by Chen and Bond, and extended the spectral range of OC absorption. We examined light absorbing properties of primary OA from pyrolysis of corn stalk, which is a major type of agricultural wastes. Light absorption of bulk liquid extracts of OA was measured using a UV-vis recording spectrophotometer. OA can be extracted by methanol at 95%, close to full extent, and shows polar character. Light absorption of organic aerosol has strong spectral dependence (Absorption Ångström exponent = 7.7) and is not negligible at ultra-violet and low-visible regions. Higher pyrolysis temperature produced OA with higher absorption. Imaginary refractive index of organic aerosol (kOA) is 0.041 at 400 nm wavelength and 0.005 at 550 nm wavelength, respectively.

  10. Removal of cadmium(II) from aqueous solution by corn stalk graft copolymers.

    Science.gov (United States)

    Zheng, Liuchun; Dang, Zhi; Zhu, Chaofei; Yi, Xiaoyun; Zhang, Hui; Liu, Congqiang

    2010-08-01

    Corn stalk was modified using graft copolymerization to produce absorbent (AGCS), which was characterized by elemental analysis, fourier transform infrared, X-ray diffraction, solid-state CP/MAS (13)C NMR spectra, thermogravimetric analysis and differential scanning calorimeter. AGCS, having cyano group (-CN) after grafted successfully, exhibits more high adsorption potential for Cd(II) than unmodified forms. The efficiency of AGCS for removal of cadmium ions was evaluated. Factors affecting Cd(II) adsorption such as pH value and adsorbent dosage were investigated. More than 90% removal was achieved at pH 3.0-7.0 and the adsorption increased from 16.0% to 99.2% with increase of adsorbent dose. In addition, two isotherm models, namely, Langmuir and Freunlich were also analyzed to determine the best fit equation for adsorption of Cd(II) on AGCS. (c) 2010 Elsevier Ltd. All rights reserved.

  11. Bed agglomeration risk related to combustion of cultivated fuels (wheat straw, red canary grass, industrial hemp) in commercial bed materials; Baeddagglomereringsrisk vid foerbraenning av odlade braenslen (hampa, roerflen, halm) i kommersiella baeddmaterial

    Energy Technology Data Exchange (ETDEWEB)

    Erhardsson, Thomas; Oehman, Marcus; Geyter, Sigrid de; Oehrstroem, Anna

    2006-12-15

    The market of forest products is expanding and thus resulting in more expensive biomass fuels. Therefore research within the combustion industry for alternative fuels is needed, for example cultivated fuels. Combustion and gasification research on these cultivated fuels are limited. The objectives of this work was to increase the general knowledge of silicon rich cultivated fuels by study the agglomeration characteristics for wheat straw, reed canary grass and industrial hemp in combination with commercial bed materials. Controlled fluidized bed agglomeration tests was conducted in a 5 kW, bench-scale, bubbling fluidized bed reactor. The tendencies of agglomeration were determined with the three cultivated fuels in combination with various minerals present in natural sand (quarts, plagioclase and potassium feldspar) and an alternative bed material (olivine). During the experiments bed samples and formed agglomerates were collected for further analyses with a scanning electron microscope (SEM) and with X-ray microanalysis (EDS). Wheat straw had the highest agglomeration tendency of the studied fuels followed by reed canary grass and industrial hemp. No significant layer formation was found around the different bed particles. Instead, the ash forming matter were found as individual ash sticky (partial melted) particles in the bed. The bed material mineralogical composition had no influence of the agglomeration process because of the non layer formation propensities of the used silicon rich fuels.

  12. Study on loading coefficient in steam explosion process of corn stalk.

    Science.gov (United States)

    Sui, Wenjie; Chen, Hongzhang

    2015-03-01

    The object of this work was to evaluate the effect of loading coefficient on steam explosion process and efficacy of corn stalk. Loading coefficient's relation with loading pattern and material property was first revealed, then its effect on transfer process and pretreatment efficacy of steam explosion was assessed by established models and enzymatic hydrolysis tests, respectively, in order to propose its optimization strategy for improving the process economy. Results showed that loading coefficient was mainly determined by loading pattern, moisture content and chip size. Both compact loading pattern and low moisture content improved the energy efficiency of steam explosion pretreatment and overall sugar yield of pretreated materials, indicating that they are desirable to improve the process economy. Pretreatment of small chip size showed opposite effects in pretreatment energy efficiency and enzymatic hydrolysis performance, thus its optimization should be balanced in investigated aspects according to further techno-economical evaluation. Copyright © 2014 Elsevier Ltd. All rights reserved.

  13. Effects of biopretreatment on pyrolysis behaviors of corn stalk by methanogen.

    Science.gov (United States)

    Wang, Tipeng; Ye, Xiaoning; Yin, Jun; Lu, Qiang; Zheng, Zongming; Dong, Changqing

    2014-07-01

    The study investigated the effects of methanogen pretreatment on pyrolysis behaviors of corn stalk (CS) by using Py-GC/MS analysis and thermogravimetric analysis. Results indicated that biopretreatment changed considerably the pyrolysis behaviors of CS from four weight loss stages to two weight loss stages. Increasing biopretreatment time from 5 days to 25 days enhanced the kinds and contents of chemicals in volatile products. In pyrolysis products, the contents of sugars, linear ketones and furans decreased from 1.43%, 12.60% and 7.38% to 1.25%, 10.22% and 3.25%, respectively, and the contents of phenols increased from 15.08% to 27.84%. The most content change from 6.83% to 13.63% indicated that methanogen pretreatment improved the pyrolysis selectivity of CS to product the 4-VP, but it was disadvantageous to 5-hydroxymethyl furfural, levoglucose and furfural. The changes of chemical compositions and structure of CS after biopretreatment were the main reason of the differences. Copyright © 2014 Elsevier Ltd. All rights reserved.

  14. Sequence Identification, Recombinant Production, and Analysis of the Self-Assembly of Egg Stalk Silk Proteins from Lacewing Chrysoperla carnea.

    Science.gov (United States)

    Neuenfeldt, Martin; Scheibel, Thomas

    2017-06-13

    Egg stalk silks of the common green lacewing Chrysoperla carnea likely comprise at least three different silk proteins. Based on the natural spinning process, it was hypothesized that these proteins self-assemble without shear stress, as adult lacewings do not use a spinneret. To examine this, the first sequence identification and determination of the gene expression profile of several silk proteins and various transcript variants thereof was conducted, and then the three major proteins were recombinantly produced in Escherichia coli encoded by their native complementary DNA (cDNA) sequences. Circular dichroism measurements indicated that the silk proteins in aqueous solutions had a mainly intrinsically disordered structure. The largest silk protein, which we named ChryC1, exhibited a lower critical solution temperature (LCST) behavior and self-assembled into fibers or film morphologies, depending on the conditions used. The second silk protein, ChryC2, self-assembled into nanofibrils and subsequently formed hydrogels. Circular dichroism and Fourier transform infrared spectroscopy confirmed conformational changes of both proteins into beta sheet rich structures upon assembly. ChryC3 did not self-assemble into any morphology under the tested conditions. Thereby, through this work, it could be shown that recombinant lacewing silk proteins can be produced and further used for studying the fiber formation of lacewing egg stalks.

  15. A Field Experiment on Enhancement of Crop Yield by Rice Straw and Corn Stalk-Derived Biochar in Northern China

    Directory of Open Access Journals (Sweden)

    Yang Yang

    2015-10-01

    Full Text Available Biochar, a green way to deal with burning and burying biomass, has attracted more attention in recent years. To fill the gap of the effects of different biochar on crop yield in Northern China, the first field experiment was conducted in farmland located in Hebei Province. Biochars derived from two kinds of feedstocks (rice straw and corn stalk were added into an Inceptisols area with different dosages (1 ton/ha, 2 ton/ha or 4 ton/ha in April 2014. The crop yields were collected for corn, peanut, and sweet potato during one crop season from spring to autumn 2014, and the wheat from winter 2014 to summer 2015, respectively. The results showed biochar amendment could enhance yields, and biochar from rice straw showed a more positive effect on the yield of corn, peanut, and winter wheat than corn stalk biochar. The dosage of biochar of 2 ton/ha or 1 ton/ha could enhance the yield by 5%–15% and biochar of 4 ton/ha could increase the yield by about 20%. The properties of N/P/K, CEC, and pH of soils amended with biochar were not changed, while biochar effects could be related to improvement of soil water content.

  16. 15N-labeled nitrogen from green manure and ammonium sulfate utilization by the sugarcane ratoon

    International Nuclear Information System (INIS)

    Ambrosano, Edmilson Jose; Rossi, Fabricio; Trivelin, Paulo Cesar Ocheuze; Cantarella, Heitor; Ambrosano, Glaucia Maria Bovi; Schammass, Eliana Aparecida; Muraoka, Takashi

    2011-01-01

    Legumes as green manure are alternative sources of nitrogen (N) for crops and can supplement or even replace mineral nitrogen fertilization due to their potential for biological nitrogen fixation (BNF). The utilization of nitrogen by sugarcane (Saccharum spp.) fertilized with sunn hemp (Crotalaria juncea L.) and ammonium sulfate (AS) was evaluated using the 15 N tracer technique. N was added at the rate of 196 and 70 kg ha -1 as 15 N-labeled sunn hemp green manure (SH) and as ammonium sulfate (AS), respectively. Treatments were: (I) Control; (II) AS 15 N; (III) SH 15 N + AS; (IV) SH 15 N; and (V) AS 15 N + SH. Sugarcane was cultivated for five years and was harvested three times. 15 N recovery was evaluated in the two first harvests. In the sum of the three harvests, the highest stalk yields were obtained with a combination of green manure and inorganic N fertilizer; however, in the second cutting the yields were higher where SH was used than in plots with AS. The recovery of N by the first two consecutive harvests accounted for 19 to 21% of the N applied as leguminous green manure and 46 to 49% of the N applied as AS. The amounts of inorganic N, derived from both N sources, present in the 0-0.4 m layer of soil in the first season after N application and were below 1 kg ha -1 . (author)

  17. {sup 15}N-labeled nitrogen from green manure and ammonium sulfate utilization by the sugarcane ratoon

    Energy Technology Data Exchange (ETDEWEB)

    Ambrosano, Edmilson Jose; Rossi, Fabricio, E-mail: ambrosano@apta.sp.gov.b [Agencia Paulista de Tecnologia dos Agronegocios (APTA), Piracicapa, SP (Brazil). Polo Rigional Centro Sul; Trivelin, Paulo Cesar Ocheuze [Centro de Energia Nuclear na Agricultura (CENA/USP), Piracicaba, SP (Brazil). Lab. de Isotopos Estaveis; Cantarella, Heitor [Agencia Paulista de Tecnologia dos Agronegocios (APTA/IAC), Campinas, SP (Brazil). Instituto Agronomico de Campinas. Centro de Solos e Recursos Agroambientais; Ambrosano, Glaucia Maria Bovi [Universidade de Campinas (UNICAMP/FOP), Piracicaba, SP (Brazil). Fac. de Odontologia de Piracicaba. Dept. de Odontologia Social, Bioestatistica; Schammass, Eliana Aparecida [Agencia Paulista de Tecnologia dos Agronegocios (APTA/IZ), Nova Odessa, SP (Brazil). Instituto de Zootecnia; Muraoka, Takashi [Centro de Energia Nuclear na Agricultura (CENA/USP), Piracicaba, SP (Brazil). Lab. de Fertilidade do solo

    2011-05-15

    Legumes as green manure are alternative sources of nitrogen (N) for crops and can supplement or even replace mineral nitrogen fertilization due to their potential for biological nitrogen fixation (BNF). The utilization of nitrogen by sugarcane (Saccharum spp.) fertilized with sunn hemp (Crotalaria juncea L.) and ammonium sulfate (AS) was evaluated using the {sup 15}N tracer technique. N was added at the rate of 196 and 70 kg ha{sup -1} as {sup 15}N-labeled sunn hemp green manure (SH) and as ammonium sulfate (AS), respectively. Treatments were: (I) Control; (II) AS{sup 15}N; (III) SH{sup 15}N + AS; (IV) SH{sup 15}N; and (V) AS{sup 15}N + SH. Sugarcane was cultivated for five years and was harvested three times. {sup 15}N recovery was evaluated in the two first harvests. In the sum of the three harvests, the highest stalk yields were obtained with a combination of green manure and inorganic N fertilizer; however, in the second cutting the yields were higher where SH was used than in plots with AS. The recovery of N by the first two consecutive harvests accounted for 19 to 21% of the N applied as leguminous green manure and 46 to 49% of the N applied as AS. The amounts of inorganic N, derived from both N sources, present in the 0-0.4 m layer of soil in the first season after N application and were below 1 kg ha{sup -1}. (author)

  18. Genotyping-by-sequencing uncovers the introgression alien segments associated with Sclerotinia basal stalk rot resistance from wild species—I. Helianthus argophyllus and H. petiolaris

    Science.gov (United States)

    Basal stalk rot (BSR), caused by Sclerotinia Sclerotiorum, is a devastating disease in sunflower worldwide. The progress of breeding for Sclerotinia BSR resistance has been hampered due to the lack of effective sources of resistance for cultivated sunflower. Our objective was to transfer BSR resista...

  19. Concentration of cadmium, zinc and manganese in root, stalk and leaf of spinach and tomato in Hamedan

    Directory of Open Access Journals (Sweden)

    A. Ghobadi

    2016-11-01

    Full Text Available Heavy metals are considers as significant environment pollutants. Their entrance into food chain is a serious health hazard to humans. This study was conducted to determine the concentrations of Cadmium, Zinc and Manganese in root, stalk and leaf portions of spinach and tomato. For this reason, during 2014 in Hamedan city, 3 farms with 5 repetitions from each farm were sampled. Samples were subjected to acid-digestion and the concentrations of the elements were assayed by inductively coupled plasma (ICP. According to the results, the average concentrations of heavy metals in root, stalk and leaf of spinach was estimated at: cadmium, 0.14, 0.24, 0.34 mg/kg, zinc, 15.53, 24.82, 35 mg/kg and manganese, 26.59, 24.42, 45.38 mg/kg, respectively. The data for the tomato samples were: cadmium, 16.20, 24.42, 33.81 mg/kg, Zinc, 21.48, 39.74, 52.92 mg/kg and manganese, 26.60, 42.41, 61.90 mg/kg, respectively. The mean concentration of cadmium and manganese in spinach and tomato showed a significant difference with the WHO/FAO standard limit. However, in the case of zinc the difference was insignificant. It was concluded that in this experiment the spinach and tomato samples were polluted with higher concentration of cadmium and manganese than the approved limit of WHO/FAO and therefore was found risky for the consumers.

  20. Altered growth, differentiation, and responsiveness to epidermal growth factor of human embryonic mesenchymal cells of palate by persistent rubella virus infection

    International Nuclear Information System (INIS)

    Yoneda, T.; Urade, M.; Sakuda, M.; Miyazaki, T.

    1986-01-01

    We previously demonstrated that human embryonic mesenchymal cells derived from the palate (HEMP cells) retain alkaline phosphatase (ALP) content and capacity for collagen synthesis after long-term culture, and their growth is markedly stimulated by epidermal growth factor (EGF). There was a dramatic decrease in ALP content and capacity to synthesize collagen in HEMP cells (HEMP-RV cells) persistently infected with rubella virus (RV). EGF increased ALP activity and decreased collagen synthesis in HEMP cells, whereas EGF showed no effect on these activities in HEMP-RV cells. Growth of HEMP-RV cells was slightly reduced compared with that of HEMP cells. EGF stimulated growth of HEMP cells and to a lesser extent of HEMP-RV cells. Binding of 125 I-EGF to cell-surface receptors in HEMP-RV cells was, to our surprise, twice as much as that in HEMP cells. However, internalization of bound 125 I-EGF in HEMP-RV cells was profoundly diminished. Thus, persistent RV infection causes not only changes in HEMP cell growth and differentiation but a decrease in or loss of HEMP cell responsiveness to EGF. The effects of persistent RV infection on palatal cell differentiation as well as growth may be responsible for the pathogenesis of congenital rubella. Furthermore, since HEMP cells appear to be closely related to osteoblasts, these results suggest a mechanism for RV-induced osseous abnormalities manifested in congenital rubella patients

  1. Characteristic and kinetics of corn stalk pyrolysis in a high pressure reactor and steam gasification of its char

    OpenAIRE

    Zhang, Guojie; Sun, Yinghui; Shi, Yuliang; Jia, Yong; Xu, Ying; Zhao, Peiyu; Zhang, Yongfa

    2016-01-01

    Pyrolysis characteristics of the corn stalk were investigated at different temperatures and pressures, with focus mainly on the releasing profiles and forming behaviors of gas. The results show that a higher pressure was conducive to the yield of H2 and CH4, and was not conducive to the generation of CO. Combustible gas components increase with the increase temperature. H2 concentration was affected significantly by temperature, was mainly released at higher temperatures (>500 °C). At 700 °C,...

  2. Removal of insecticide carbofuran from aqueous solutions by banana stalks activated carbon

    International Nuclear Information System (INIS)

    Salman, J.M.; Hameed, B.H.

    2010-01-01

    In this work, activated carbon was prepared from banana stalks (BSAC) waste to remove the insecticide carbofuran from aqueous solutions. The effects of contact time, initial carbofuran concentration, solution pH and temperature (30, 40 and 50 deg. C) were investigated. Adsorption isotherm, kinetics and thermodynamics of carbofuran on BSAC were studied. Equilibrium data were fitted to the Langmuir, Freundlich and Temkin isotherm models and the data best represented by the Langmuir isotherm. Thermodynamic parameters such as standard enthalpy (ΔH o ), standard entropy (ΔS o ) and standard free energy (ΔG o ) were evaluated. Regeneration efficiency of spent BSAC was studied using ethanol as a solvent. The efficiency was found to be in the range of 96.97-97.35%. The results indicated that the BSAC has good regeneration and reusability characteristics and can be used as alternative to present commercial activated carbon.

  3. Biocompatible nanoemulsions based on hemp oil and less surfactants for oral delivery of baicalein with enhanced bioavailability.

    Science.gov (United States)

    Yin, Juntao; Xiang, Cuiyu; Wang, Peiqing; Yin, Yuyun; Hou, Yantao

    2017-01-01

    Baicalein (BCL) possesses high pharmacological activities but low solubility and stability in the intestinal tract. This study aimed to probe the potential of nanoemulsions (NEs) consisting of hemp oil and less surfactants in ameliorating the oral bioavailability of BCL. BCL-loaded NEs (BCL-NEs) were prepared by high-pressure homogenization technique to reduce the amount of surfactants. BCL-NEs were characterized by particle size, entrapment efficiency (EE), in vitro drug release, and morphology. Bioavailability was studied in Sprague-Dawley rats following oral administration of BCL suspensions, BCL conventional emulsions, and BCL-NEs. The obtained NEs were ~90 nm in particle size with an EE of 99.31%. BCL-NEs significantly enhanced the oral bioavailability of BCL, up to 524.7% and 242.1% relative to the suspensions and conventional emulsions, respectively. BCL-NEs exhibited excellent intestinal permeability and transcellular transport ability. The cytotoxicity of BCL-NEs was documented to be low and acceptable for oral purpose. Our findings suggest that such novel NEs and preparative process provide a promising alternative to current formulation technologies and suitable for oral delivery of drugs with bioavailability issues.

  4. Permeability transition in human mitochondria persists in the absence of peripheral stalk subunits of ATP synthase.

    Science.gov (United States)

    He, Jiuya; Carroll, Joe; Ding, Shujing; Fearnley, Ian M; Walker, John E

    2017-08-22

    The opening of a nonspecific channel, known as the permeability transition pore (PTP), in the inner membranes of mitochondria can be triggered by calcium ions, leading to swelling of the organelle, disruption of the inner membrane and ATP synthesis, and cell death. Pore opening can be inhibited by cyclosporin A mediated via cyclophilin D. It has been proposed that the pore is associated with the dimeric ATP synthase and the oligomycin sensitivity conferral protein (OSCP), a component of the enzyme's peripheral stalk, provides the site at which cyclophilin D interacts. Subunit b contributes a central α-helical structure to the peripheral stalk, extending from near the top of the enzyme's catalytic domain and crossing the membrane domain of the enzyme via two α-helices. We investigated the possible involvement of the subunit b and the OSCP in the PTP by generating clonal cells, HAP1-Δb and HAP1-ΔOSCP, lacking the membrane domain of subunit b or the OSCP, respectively, in which the corresponding genes, ATP5F1 and ATP5O , had been disrupted. Both cell lines preserve the characteristic properties of the PTP; therefore, the membrane domain of subunit b does not contribute to the PTP, and the OSCP does not provide the site of interaction with cyclophilin D. The membrane subunits ATP6, ATP8, and subunit c have been eliminated previously from possible participation in the PTP; thus, the only subunits of ATP synthase that could participate in pore formation are e, f, g, diabetes-associated protein in insulin-sensitive tissues (DAPIT), and the 6.8-kDa proteolipid.

  5. The effect of plant density and nitrogen fertilizer on light interception and dry matter yield in hemp (Cannabis sativa L.

    Directory of Open Access Journals (Sweden)

    mohamad reza asghari poor

    2009-06-01

    Full Text Available The effect of plant density and nitrogen fertilizer on canopy light interception and on flowering was investigated in hemp (Cannabis sativa L. cv. ‘Kompolti’ Crop grown at initial densities of 50, 150 and 250 plants/m2 at the Mashhad and 30, 90 and 150 plants/m2 at the Shirvan. Nitrogen fertilizer was applied before and 45 days after sowing at a rates of 50 and 200 kg/ha at the Mashhad, and 50, 150 and 250 kg/ha at the Shirvan. Rate of canopy development increased with increasing plant density and nitrogen fertilizer in both sites. At the Mashhad, interception of 90% of light was attained at 380 to 665 degree days (base 2°C from emergence for the crop grown at different densities. At Shirvan, rate of canopy development was slower. Interception of 90% of light was attained at 586 degree days from emergence for the crop grown at 30 plants/m2 and at 712 degree days for the crop grown at 150 plants/m2, probably as a result of cold weather. Nitrogen fertilizer in a similar way as plant density increased light interception. Maximum light interception did not depend on plant density and nitrogen fertilizer and was about 95%. In both sites, the flowering date was later with increasing plant density. Dates of 75% flowering for the initial densities of 50, 150 and 250 plants/m2 in Mashhad and 30, 90 and 150 plants/m2 in Shirvan were, respectively 26 August, 1, 6, 6, 11 and 12 September. Independent of plant density, canopy light interception started to decline at about 150 degree days after flowering, reaching 58 to 75% at about 700 degree days post-flowering. Morphological characteristics at both sites were highly correlated with plant sexual, plant population and nitrogen fertilizer. Highest stem, leaf and inflorescence yield were obtained in Mashhad at 250 plant/m-2 and in Shirvan at 150 plant m-2 when 200 kg N ha-1 in Mashhad and 250 kg N/ha in Shirvan was used. Above ground dry matter increased at both sites with increasing plant density and

  6. Sex-biased gene expression during head development in a sexually dimorphic stalk-eyed fly.

    Directory of Open Access Journals (Sweden)

    Gerald S Wilkinson

    Full Text Available Stalk-eyed flies (family Diopsidae are a model system for studying sexual selection due to the elongated and sexually dimorphic eye-stalks found in many species. These flies are of additional interest because their X chromosome is derived largely from an autosomal arm in other flies. To identify candidate genes required for development of dimorphic eyestalks and investigate how sex-biased expression arose on the novel X, we compared gene expression between males and females using oligonucleotide microarrays and RNA from developing eyestalk tissue or adult heads in the dimorphic diopsid, Teleopsis dalmanni. Microarray analysis revealed sex-biased expression for 26% of 3,748 genes expressed in eye-antennal imaginal discs and concordant sex-biased expression for 86 genes in adult heads. Overall, 415 female-biased and 482 male-biased genes were associated with dimorphic eyestalk development but not differential expression in the adult head. Functional analysis revealed that male-biased genes are disproportionately associated with growth and mitochondrial function while female-biased genes are associated with cell differentiation and patterning or are novel transcripts. With regard to chromosomal effects, dosage compensation occurs by elevated expression of X-linked genes in males. Genes with female-biased expression were more common on the X and less common on autosomes than expected, while male-biased genes exhibited no chromosomal pattern. Rates of protein evolution were lower for female-biased genes but higher for genes that moved on or off the novel X chromosome. These findings cannot be due to meiotic sex chromosome inactivation or by constraints associated with dosage compensation. Instead, they could be consistent with sexual conflict in which female-biased genes on the novel X act primarily to reduce eyespan in females while other genes increase eyespan in both sexes. Additional information on sex-biased gene expression in other tissues and

  7. Lipophilic extractives from several nonwoody lignocellulosic crops (flax, hemp, sisal, abaca) and their fate during alkaline pulping and TCF/ECF bleaching.

    Science.gov (United States)

    Marques, Gisela; del Río, José C; Gutiérrez, Ana

    2010-01-01

    The fate of lipophilic extractives from several nonwoody species (flax, hemp, sisal and abaca) used for the manufacturing of cellulose pulps, was studied during soda/anthraquinone (AQ) pulping and totally chorine free (TCF) and elemental chlorine free (ECF) bleaching. With this purpose, the lipophilic extracts from the raw materials and their unbleached and bleached industrial pulps, were analyzed by gas chromatography-mass spectrometry. Aldehydes, hydroxyfatty acids and esterified compounds such as ester waxes, sterol esters and alkylferulates strongly decreased after soda/AQ pulping while alkanes, alcohols, free sterols and sterol glycosides survived the cooking process. Among the lipophilic extractives that remained in the unbleached pulps, some amounts of free sterols were still present in the TCF pulps whereas they were practically absent in the ECF pulps. Sterol glycosides were also removed after both TCF and ECF bleaching. By contrast, saturated fatty acids, fatty alcohols and alkanes were still present in both bleached pulps.

  8. Stalking: una ricerca sull’”ammonimento del Questore” nella provincia di Bologna in riferimento alla Legge 38/2009 / Le stalking : analyse du « rappel à la loi » par le préfet de Police du département de Bologne (Loi n°38 du 2009 / Stalking: analysis of restraining order issued by the Chief of Police in the province of Bologna (law n° 38/2009

    Directory of Open Access Journals (Sweden)

    Salsi Giancarlo

    2012-04-01

    Full Text Available The restraining order issued by the Chief of Police is a legal instrument that is used to protect the victim of stalking with the aim of dissuading the stalker from doing more persecutory acts. Neither executive decrees nor circulars are issued yet to define an equal national application procedure. For this reason, the author presents the procedure used by the Police headquarters of Bologna and the data concerning acts of stalking committed in Bologna and its province three years after the approval of the law n° 38/2009. La protection de la victime de harcèlement moral trouve dans le « rappel à la loi » de l’Autorité de Sécurité Publique un instrument juridique qui peut être utilisé afin de dissuader l’auteur de perpétrer d’autres actions criminelles. Compte tenu du de l’absence de décrets d’exécution et/ou de circulaires visant à une application uniforme de cet instrument au niveau national, nous présentons la procédure adoptée par le préfet de Police de Bologne, ainsi que les données relatives à ce phénomène concernent la ville et le département de Bologne, trois ans après la promulgation de la loi.

  9. Male sexual ornament size is positively associated with reproductive morphology and enhanced fertility in the stalk-eyed fly Teleopsis dalmanni

    Directory of Open Access Journals (Sweden)

    Chapman Tracey

    2008-08-01

    Full Text Available Abstract Background Exaggerated male ornaments and displays often evolve in species where males only provide females with ejaculates during reproduction. Although "good genes" arguments are typically invoked to explain this phenomenon, a simpler alternative is possible if variation in male reproductive quality (e.g. sperm number, ejaculate content, mating rate is an important determinant of female reproductive success. The "phenotype-linked fertility hypothesis" states that female preference for male ornaments or displays has been selected to ensure higher levels of fertility and has driven the evolution of exaggerated male traits. Females of the stalk-eyed fly Teleopsis dalmanni must mate frequently to maintain high levels of fertility and prefer to mate with males exhibiting large eyespan, a condition-dependent sexual ornament. If eyespan indicates male reproductive quality, females could directly increase their reproductive success by mating with males with large eyespan. Here we investigate whether male eyespan indicates accessory gland and testis length, and then ask whether mating with large eyespan males affects female fertility. Results Male eyespan was a better predictor of two key male reproductive traits – accessory gland and testis length – than was body size alone. This positive relationship held true over three levels of increasing environmental stress during the maturation of the adult accessory glands and testes. Furthermore, females housed with a large eyespan male exhibited higher levels of fertility than those with small eyespan males. Conclusion Male eyespan in stalk-eyed flies is subject to strong directional mate preference and is a reliable indicator of male reproductive quality – both because males with larger eyespan have bigger accessory glands and testes, and also as they confer higher fertility on females. Fertility enhancement may have arisen because males with larger eyespan mated more often and/or because

  10. Endoscopic endonasal approach for craniopharyngioma: the importance of the relationship between pituitary stalk and tumor.

    Science.gov (United States)

    Dho, Yun-Sik; Kim, Yong Hwy; Se, Young-Bem; Han, Doo Hee; Kim, Jung Hee; Park, Chul-Kee; Wang, Kyu-Chang; Kim, Dong Gyu

    2017-09-29

    OBJECTIVE The endoscopic endonasal approach (EEA) is commonly used for the treatment of craniopharyngioma; therefore, it is essential to analyze outcomes in order to understand the benefits and drawbacks. The goal of this paper was to evaluate the clinical features and outcomes associated with this treatment approach. METHODS From July 2010 to March 2016, 82 adult craniopharyngioma patients underwent an EEA at the authors' institution. Of these cases, intraoperative records and immediate postoperative MR images were available for 68 patients. The patients underwent systemized endocrinological evaluation. Eighteen of 68 patients who underwent EEA for recurrence or regrowth of residual lesions after previous surgical management were excluded in the analysis of the anatomical tumor classification. The authors retrospectively analyzed preoperative clinical features and previous anatomical classifications, focusing on the relationship of the pituitary stalk and tumor, to determine predictive factors for the clinical outcome, such as the extent of resection, visual function, endocrinological function, recurrence rate, and complications. RESULTS The mean tumor size was 2.5 cm (3.1 cm for primary tumors and 1.9 cm for recurrent lesions). Gross-total resection (GTR) was achieved in 62 (91.1%) patients (48 [96.0%] patients with primary tumors and 14 [77.8%] patients with recurrent tumors). The rate of GTR was higher in the primary group than in the group with recurrence (p = 0.038). The overall pre- and postoperative visual impairment scale (VIS) scores were 40.8 and 22.1, respectively (50.9 and 14.3 in the primary group and 30.7 and 29.9 in patients with recurrence, respectively). The improvement rate in VIS score was higher in the primary group than in the recurrent group (p = 0.001). Endocrinological function was improved in 4 patients (5.9%) and deteriorated in 32 of 68 patients (47.1%). Tumor invasion into the center of the pituitary stalk affected the postoperative

  11. In vitro and in situ degradation of alkali treated sorghum wet distillers grains alone or in combination with corn stalks to increase their nutritive value

    Science.gov (United States)

    This experiment was conducted to evaluate the effect of alkali treatment on in vitro and in situ digestibility of fiber sources. An in vitro and in situ experiment were conducted to determine the effects of treating sorghum WDG with solubles (SWDG) and corn stalks (CS) with calcium hydroxide on in ...

  12. Chromium sorption and Cr(VI) reduction to Cr(III) by grape stalks and yohimbe bark.

    Science.gov (United States)

    Fiol, Núria; Escudero, Carlos; Villaescusa, Isabel

    2008-07-01

    In this work, two low cost sorbents, grape stalks and yohimbe bark wastes were used to remove Cr(VI) and Cr(III) from aqueous solutions. Batch experiments were designed to obtain Cr(VI) and Cr(III) sorption data. The mechanism of Cr(III) and Cr(VI) removal and Cr(VI) reduction to Cr(III) by the two vegetable wastes, has been investigated. Fourier transform infrared rays (FTIR) and X-ray photoelectron spectroscopy (XPS) analysis on solid phase were performed to determine the main functional groups that might be involved in metal uptake and to confirm the presence of Cr(III) on the sorbent, respectively. Results put into evidence that both sorbents are able to reduce Cr(VI) to its trivalent form.

  13. A transposon-directed epigenetic change in ZmCCT underlies quantitative resistance to Gibberella stalk rot in maize.

    Science.gov (United States)

    Wang, Chao; Yang, Qin; Wang, Weixiang; Li, Yipu; Guo, Yanling; Zhang, Dongfeng; Ma, Xuena; Song, Wei; Zhao, Jiuran; Xu, Mingliang

    2017-09-01

    A major resistance quantitative trait locus, qRfg1, significantly enhances maize resistance to Gibberella stalk rot, a devastating disease caused by Fusarium graminearum. However, the underlying molecular mechanism remains unknown. We adopted a map-based cloning approach to identify the resistance gene at qRfg1 and examined the dynamic epigenetic changes during qRfg1-mediated maize resistance to the disease. A CCT domain-containing gene, ZmCCT, is the causal gene at the qRfg1 locus and a polymorphic CACTA-like transposable element (TE1) c. 2.4 kb upstream of ZmCCT is the genetic determinant of allelic variation. The non-TE1 ZmCCT allele is in a poised state, with predictive bivalent chromatin enriched for both repressive (H3K27me3/H3K9me3) and active (H3K4me3) histone marks. Upon pathogen challenge, this non-TE1 ZmCCT allele was promptly induced by a rapid yet transient reduction in H3K27me3/H3K9me3 and a progressive decrease in H3K4me3, leading to disease resistance. However, TE1 insertion in ZmCCT caused selective depletion of H3K4me3 and enrichment of methylated GC to suppress the pathogen-induced ZmCCT expression, resulting in disease susceptibility. Moreover, ZmCCT-mediated resistance to Gibberella stalk rot is not affected by photoperiod sensitivity. This chromatin-based regulatory mechanism enables ZmCCT to be more precise and timely in defense against F. graminearum infection. © 2017 The Authors. New Phytologist © 2017 New Phytologist Trust.

  14. Pyrolysis of rice husk and corn stalk in auger reactor:Part 1. Characterization of char and gas at various temperatures

    OpenAIRE

    Yu, Yang; Yang, Yang; Cheng, Zhicai; Blanco, Paula H.; Liu, Ronghou; Bridgwater, A.V.; Cai, Junmeng

    2016-01-01

    In this study, rice husk and corn stalk have been pyrolyzed in an auger pyrolysis reactor at pyrolysis temperatures of 350, 400, 450, 500, 550, and 600 °C in order to investigate the effect of the pyrolysis temperature on the pyrolysis performance of the reactor and physicochemical properties of pyrolysis products (this paper focuses on char and gas). The results have shown that the pyrolysis temperature significantly affects the mass yields and properties of the pyrolysis products. The mass ...

  15. Effect of compatibilizing agents on the interface and mechanical behaviour of polypropylene/hemp bast fiber biocomposites

    Science.gov (United States)

    Boruvka, M.; Lenfeld, P.; Brdlik, P.; Behalek, L.

    2015-07-01

    During the last years automotive industry has given a lot of attention to the biobased polymers that are sustainable and eco-friendly. Nevertheless fully green composites are currently too expensive for most applications. A viable solution and logical starting point at this material revolution lies in reinforced synthetic thermoplastics based on plant derived biodegradable fibers. Plant fibers (PF's) have potential to reduce weight of composite vehicle parts up to 40% compared with the main automotive composites filler, glass fibers (GF's). Production of GF's composites is much more energy intensive and polluting compared with growing, harvesting and preparing of PF's. The main disadvantage of PF's lies in combination of non-polar hydrophobic polymer matrix and polar hydrophilic fibers. This combination creates poor interface with low adhesion of both components. That implies poor wettability of fibres by polymer matrix and low mechanical properties of biocomposites. Therefore specific compatibilizing agents (Struktol SA1012, Fusabond P353, Smart + Luperox) were used in order to enhance compatibility between reinforcement and matrix. In this paper sets of biocomposite compounds were prepared by twin screw extrusion considering different type and weight percentage (wt. %) of compatibilizing agents, hemp bast fibres (HBF's) within ratio 20 (wt. %) and polypropylene (PP) THERMOFIL PP E020M matrix. Resulting compounds were than injection molded and tested samples were characterized by means of scanning electron microscopy (SEM) and mechanical testing.

  16. Effect of urea and urea-gamma treatments on cellulose degradation of Thai rice straw and corn stalk

    International Nuclear Information System (INIS)

    Banchorndhevakul, Siriwattana

    2002-01-01

    Cellulose degradation of 20% urea treated and 20% urea-10 kGy gamma treated Thai rice straw and corn stalk showed that combination effect of urea and gamma radiation gave a higher % decrease in neutral detergent fiber (NDF), acid detergent fiber (ADF), acid detergent lignin (ADL), cellulose, hemicellulose, and lignin and cutin in comparison with urea effect only for both room temperature storage and room temperature +258 K storage. The results also indicated that cellulose degradation proceeded with time, even at 258 K. A drastic drop to less than half of the original contents in NDF, ADF, and ADL could not be obtained in this study

  17. Effect of urea and urea-gamma treatments on cellulose degradation of Thai rice straw and corn stalk

    Science.gov (United States)

    Banchorndhevakul, Siriwattana

    2002-08-01

    Cellulose degradation of 20% urea treated and 20% urea-10 kGy gamma treated Thai rice straw and corn stalk showed that combination effect of urea and gamma radiation gave a higher % decrease in neutral detergent fiber (NDF), acid detergent fiber (ADF), acid detergent lignin (ADL), cellulose, hemicellulose, and lignin and cutin in comparison with urea effect only for both room temperature storage and room temperature +258 K storage. The results also indicated that cellulose degradation proceeded with time, even at 258 K. A drastic drop to less than half of the original contents in NDF, ADF, and ADL could not be obtained in this study.

  18. Effect of dilute alkaline pretreatment on the conversion of different parts of corn stalk to fermentable sugars and its application in acetone-butanol-ethanol fermentation.

    Science.gov (United States)

    Cai, Di; Li, Ping; Luo, Zhangfeng; Qin, Peiyong; Chen, Changjing; Wang, Yong; Wang, Zheng; Tan, Tianwei

    2016-07-01

    To investigate the effect of dilute alkaline pretreatment on different parts of biomass, corn stalk was separated into flower, leaf, cob, husk and stem, which were treated by NaOH in range of temperature and chemical loading. The NaOH-pretreated solid was then enzymatic hydrolysis and used as the substrate for batch acetone-butanol-ethanol (ABE) fermentation. The results demonstrated the five parts of corn stalk could be used as potential feedstock separately, with vivid performances in solvents production. Under the optimized conditions towards high product titer, 7.5g/L, 7.6g/L, 9.4g/L, 7g/L and 7.6g/L of butanol was obtained in the fermentation broth of flower, leaf, cob, husk and stem hydrolysate, respectively. Under the optimized conditions towards high product yield, 143.7g/kg, 126.3g/kg, 169.1g/kg, 107.7g/kg and 116.4g/kg of ABE solvent were generated, respectively. Copyright © 2016 Elsevier Ltd. All rights reserved.

  19. Isolation and Characteristics of Cellulose and Nanocellulose from Lotus Leaf Stalk Agro-wastes

    Directory of Open Access Journals (Sweden)

    Yandan Chen

    2014-12-01

    Full Text Available Valorization of lotus leaf stalks (LLS produced as an abundantly available agro-waste was achieved through the extraction of value-added nanocellulose. Nanofibrillated cellulose (NFC was successfully prepared from LLS by using chemical pretreatment combined with high-intensity ultrasonication. The morphological characteristics of the chemically purified LLS cellulose microfibrils were characterized by optical microscopy and MorFi fiber analysis. Fourier transform infrared (FTIR spectroscopy indicated the extensive removal of non-cellulosic components after chemical pretreatment. The transmission electron microscopy (TEM results revealed agglomeration of the developed individual NFC, with a width of 20 ± 5 nm and length on a micron scale, into a network-like feature. X-ray diffraction results showed that the resulting NFC had a cellulose I crystal structure with a high crystallinity (70%. The NFC started to degrade at around 217 °C, and the peak rate of degradation occurred at 344 °C. Nanofibrils obtained from LLS have great potential as reinforcement agents in nanocomposites.

  20. Flute type micropores activated carbon from cotton stalk for high performance supercapacitors

    Science.gov (United States)

    Tian, Xun; Ma, Hongru; Li, Zhe; Yan, Shaocun; Ma, Lei; Yu, Feng; Wang, Gang; Guo, Xuhong; Ma, Yanqing; Wong, Chingping

    2017-08-01

    Flute type micropores activated carbon (FTMAC) has been successfully obtained from cotton stalk via KOH-chemical activation method. The synthesized carbon material exhibits an ordered pore structure with high specific surface area of 1964.46 m2 g-1 and pore volume of 1.03 m3 g-1. The assembled FTMAC-based electrode delivers a high specific capacitance of 254 F g-1 at a current density of 0.2 A g-1 in 1 M H2SO4 aqueous electrolyte. It still can maintain 221 F g-1at a current density of 10 A g-1, demonstrating a good rate capacity (87% retention), as well as long cyclic stability of 96% capacitance retention after 10000 charging and discharging cycles at current density of 1 A g-1. Moreover, the symmetric supercapacitor can deliver a high energy density of 18.14 W h kg-1 and a power density of 450.37 W kg-1 which is operated in the voltage range of 0-1.8 V.